WorldWideScience

Sample records for surface impoundments utility

  1. Surface mine impoundments as wildlife and fish habitat

    Science.gov (United States)

    Mark A. Rumble

    1989-01-01

    Unreclaimed surface mine impoundments provide poor fish and wildlife habitat. Recommendations given here for reclaiming "prelaw" impoundments and creating new impoundments could provide valuable fish and wildlife habitat if incorporated into existing laws and mine plans.

  2. Closure certification report: TA-35 TSL-125 surface impoundment

    International Nuclear Information System (INIS)

    1991-01-01

    This report summarizes the actions that were taken to clean close the TA-35 TSL-125 surface impoundment Building 125 is used for developing electron guns and related laser assemblies/equipment for a Laser Technology Research Program at the Laboratory. There is no permanent outfall from the surface impoundment; however, the impoundment accidentally overtopped on December 3, 1986, spilling an unknown volume of insulating oil and water into Ten Site Canyon. Sandbags were installed around the surface impoundment on June 25, 1988, to provide additional freeboard in the impoundment and reduce the risk of overtopping during a precipitation event. On July 1, 1988, the impoundment again overtopped releasing an unknown volume of insulating oil and water. Actions taken include removal of waste from the surface impoundment and its associated structures, decontamination of the floor trough and piping inside Building 125, grouting of the piping connecting the floor drain/trough system to the impoundment, decontamination, removal, and disposal of the impoundment liner and sandbags lining the top of the impoundment, and removal and disposal of contaminated soil underlying the impoundment area. Procedures followed to verify that clean closure objectives have been met are also documented in this report. Initial verification was performed through an extensive soil sampling and analysis program

  3. Closure certification report: TA-35 TSL-125 surface impoundment

    International Nuclear Information System (INIS)

    1991-01-01

    This closure report documents closure activities for the TA-35 TSL-125 surface impoundment and associated structures at Los Alamos National Laboratory (the Laboratory). Prior to formal approval of the closure plan, the decision was made to proceed with closure activities to prevent any further releases from the site following informal discussions with New Mexico Environment Department (NMED) personnel. The closure plan is a revision of the previously submitted draft dated July 1988. Clean closure of the TSL-125 site was accomplished through: Removal and proper disposal of all wastes contained within the surface impoundment system; Decontamination and/or removal and proper disposal of the surface impoundment, its associated structures, and contaminated soil underlying the impoundment area; Sampling and analysis of soil to determine the presence and concentrations of any hazardous constituents remaining in the soil at the TSL-125 site; and Demonstration through a risk assessment that any constituents remaining in the soil at the TSL-125 site pose no threat to human health and the environment. All remaining soil concentrations of hazardous constituents were below health-based action levels. Analytical results indicated that benzidine, n-nitrosodimethylamine, and n-nitrosodi-n-propylamine were not detected at or above their limits of quantitation and beryllium was not present at or above its laboratory detection limit. However, the limits of quantitation and detection for these constituents were greater than their calculated health-based action levels. To demonstrate that these constituents were not present, historical data was researched and it was determined that the constituents were not utilized at the Building 125 site. 4 refs., 8 figs., 1 tab

  4. 40 CFR 63.134 - Process wastewater provisions-surface impoundments.

    Science.gov (United States)

    2010-07-01

    ... wastewater provisions—surface impoundments. (a) For each surface impoundment that receives, manages, or...-supported structure or rigid cover) and a closed-vent system that routes the organic hazardous air... to float on the liquid surface during normal operations, and to form a continuous barrier over the...

  5. Technical work plan for Surface Impoundments Operable Unit engineering support studies

    International Nuclear Information System (INIS)

    1995-11-01

    This document provides a comprehensive work plan which, when utilized as a data collection guide for field activities, will provide the necessary information required to complete a report on geotechnical properties of the sediments contained in the Surface Impoundments Operable Unit at Oak Ridge National Laboratory in Oak Ridge, Tennessee. Detailed guidance is provided for the following activities: collection of samples from the impoundments; compressive strength testing of the raw sediments; compressive strength testing of the structurally modified (lime and cement additives) sediments; testing for sediment physical properties and settling rates; testing for sediment dewatering characteristics; testing for radiation activity during the field work; testing for polymer additions that may enhance settling. The work plan additionally provides guidance and examples for the preparation of documents necessary to establish readiness for safe and satisfactory performance of the field activities. An outline for the format requested for a report of these data is also provided

  6. 40 CFR 63.943 - Standards-Surface impoundment vented to control device.

    Science.gov (United States)

    2010-07-01

    ... applicable, to the surface impoundment. (ii) To remove accumulated sludge or other residues from the bottom... the following requirements: (1) The cover and its closure devices shall be designed to form a...

  7. 40 CFR 63.942 - Standards-Surface impoundment floating membrane cover.

    Science.gov (United States)

    2010-07-01

    ... operations, and form a continuous barrier over the entire surface area of the liquid. (2) The cover shall be... closure device in the closed position, as applicable. (ii) To remove accumulated sludge or other residues from the bottom of surface impoundment. (2) Opening of a spring-loaded pressure-vacuum relief valve...

  8. Coal combustion waste management at landfills and surface impoundments 1994-2004.

    Energy Technology Data Exchange (ETDEWEB)

    Elcock, D.; Ranek, N. L.; Environmental Science Division

    2006-09-08

    on CCW disposal practices and State regulatory requirements at landfills and surface impoundments that were permitted, built, or laterally expanded between January 1, 1994, and December 31, 2004. The scope of the study excluded waste units that manage CCWs in active or abandoned coal mines. The EPA identified the following three areas of interest: (1) Recent and current CCW industry surface disposal management practices, (2) State regulatory requirements for CCW management, and (3) Implementation of State requirements (i.e., the extent to which States grant or deny operator requests to waive or vary regulatory requirements and the rationales for doing so). DOE and the EPA obtained data on recent and current disposal practices from a questionnaire that the Utility Solid Waste Activities Group (USWAG) distributed to its members that own or operate coal-fired power plants. USWAG, formed in 1978, is responsible for addressing solid and hazardous waste issues on behalf of the utility industry. It is an informal consortium of approximately 80 utility operating companies, the Edison Electric Institute (EEI), the National Rural Electric Cooperative Association (NRECA), the American Public Power Association (APPA), and the American Gas Association (AGA). EEI is the principal national association of investor-owned electric power and light companies. NRECA is the national association of rural electric cooperatives. APPA is the national association of publicly owned electric utilities. AGA is the national association of natural gas utilities. Together, USWAG member companies and trade associations represent more than 85% of the total electric generating capacity of the United States and service more than 95% of the nation's consumers of electricity. To verify the survey findings, the EPA also asked State regulators from nine selected States that are leading consumers of coal for electricity generation for information on disposal units that may not have been covered in the

  9. Transport and dispersion of pollutants in surface impoundments: a finite element model

    International Nuclear Information System (INIS)

    Yeh, G.T.

    1980-07-01

    A surface impoundment model in finite element (SIMFE) is presented to enable the simulation of flow circulations and pollutant transport and dispersion in natural or artificial lakes, reservoirs or ponds with any number of islands. This surface impoundment model consists of two sub-models: hydrodynamic and pollutant transport models. Both submodels are simulated by the finite element method. While the hydrodynamic model is solved by the standard Galerkin finite element scheme, the pollutant transport model can be solved by any of the twelve optional finite element schemes built in the program. Theoretical approximations and the numerical algorithm of SIMFE are described. Detail instruction of the application are given and listing of FORTRAN IV source program are provided. Two sample problems are given. One is for an idealized system with a known solution to show the accuracy and partial validation of the models. The other is applied to Prairie Island for a set of hypothetical input data, typifying a class of problems to which SIMFE may be applied

  10. Transport and dispersion of pollutants in surface impoundments: a finite element model

    Energy Technology Data Exchange (ETDEWEB)

    Yeh, G.T.

    1980-07-01

    A surface impoundment model in finite element (SIMFE) is presented to enable the simulation of flow circulations and pollutant transport and dispersion in natural or artificial lakes, reservoirs or ponds with any number of islands. This surface impoundment model consists of two sub-models: hydrodynamic and pollutant transport models. Both submodels are simulated by the finite element method. While the hydrodynamic model is solved by the standard Galerkin finite element scheme, the pollutant transport model can be solved by any of the twelve optional finite element schemes built in the program. Theoretical approximations and the numerical algorithm of SIMFE are described. Detail instruction of the application are given and listing of FORTRAN IV source program are provided. Two sample problems are given. One is for an idealized system with a known solution to show the accuracy and partial validation of the models. The other is applied to Prairie Island for a set of hypothetical input data, typifying a class of problems to which SIMFE may be applied.

  11. 40 CFR 63.7905 - What emissions limitations or work practice standards must I meet for surface impoundments?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 13 2010-07-01 2010-07-01 false What emissions limitations or work practice standards must I meet for surface impoundments? 63.7905 Section 63.7905 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE...

  12. Post-remediation action radiological report for Surface Impoundments C (3539) and D (3540) at the Oak Ridge National Laboratory, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    1998-12-01

    During August and September 1998, Bechtel Jacobs Company LLC performed a remedial action within Impoundments 3539 and 3540 (Impoundments C and D, respectively) in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act Record of Decision (ROD) for the Surface Impoundments Operable Unit. The remedial action included removal of sediments and 0.1 ft of subimpoundment soil. A post-remedial action radiological survey was conducted to provide data to support the Bethel Valley ROD. Data was obtained from (1) a walkover survey for residual gamma radiation on the base of the impoundments, (2) smear surveys for transferable contamination on remaining riprap, and (3) representative sampling of subimpoundment soils. Walkover surveys identified no locations outside the impoundments with gamma exposure levels greater than three times background levels. Smear surveys detected no removable contamination above release limits as specified in 10 CFR 835, Appendix D. Subimpoundment soil samples quantified low levels of residual contamination

  13. Post-remediation action radiological report for Surface Impoundments C (3539) and D (3540) at the Oak Ridge National Laboratory, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-01

    During August and September 1998, Bechtel Jacobs Company LLC performed a remedial action within Impoundments 3539 and 3540 (Impoundments C and D, respectively) in accordance with the Comprehensive Environmental Response, Compensation, and Liability Act Record of Decision (ROD) for the Surface Impoundments Operable Unit. The remedial action included removal of sediments and 0.1 ft of subimpoundment soil. A post-remedial action radiological survey was conducted to provide data to support the Bethel Valley ROD. Data was obtained from (1) a walkover survey for residual gamma radiation on the base of the impoundments, (2) smear surveys for transferable contamination on remaining riprap, and (3) representative sampling of subimpoundment soils. Walkover surveys identified no locations outside the impoundments with gamma exposure levels greater than three times background levels. Smear surveys detected no removable contamination above release limits as specified in 10 CFR 835, Appendix D. Subimpoundment soil samples quantified low levels of residual contamination.

  14. Probabilistic risk assessment for the Sandia National Laboratories Technical Area V Liquid Waste Disposal System surface impoundments

    International Nuclear Information System (INIS)

    Dawson, L.A.; Eidson, A.F.

    1996-01-01

    A probabilistic risk assessment was completed for a former radioactive waste disposal site. The site, two unlined surface impoundment, was designed as part of the Liquid Waste Disposal System (LWDS) to receive radioactive effluent from nuclear reactors in Technical Area-V (TA-V) at Sandia National Laboratories/New Mexico (SNL/NM). First, a statistical comparison of site sampling results to natural background, using EPA methods, and a spatial distribution analysis were performed. Risk assessment was conducted with SNL/NM's Probabilistic Risk Evaluation and Characterization Investigation System model. The risk assessment indicated that contamination from several constituents might have been high enough to require remediation. However, further analysis based on expected site closure activities and recent EPA guidance indicated that No Further Action was acceptable

  15. Results of the measurement survey of elevation and environmental media in surface impoundments 3513 (B) and 3524 (A) at Oak Ridge National Laboratory, Oak Ridge, TN

    Energy Technology Data Exchange (ETDEWEB)

    Murray, M.E.; Rose, D.A.; Brown, K.S.; Coe, R.H.C. III; Lawrence, J.D.; Winton, W.

    1998-07-01

    A measurement survey of the elevation and environmental media in impoundments 3513 (B) and 3524 (A) at the Oak Ridge National Laboratory (ORNL) was conducted during April 1998. The investigation was performed by the Measurement Applications and Development Group of the Life Sciences Division of ORNL at the request of Bechtel Jacobs Company. Measurement activities were conducted at selected locations in order to determine the depth and appearance of the sediment and describe the clay underlying the impoundments prior to remediation. The survey was a follow-up to a previous elevation survey. The survey included the following: collection of sediment/clay cores from selected locations in each impoundment; measurement and documentation of the elevation at the water surface, at the top of sediment, at the top of clay, and at the bottom of each core; visual inspection of each core by a soil scientist to confirm the presence of clay and not material such as fly ash and soda lime compacted over the last 50 years; measurement and documentation of the background beta-gamma radiation level at the time and location of collection of each core, the highest beta-gamma level along the sediment portion of each core, and the highest beta-gamma level along the clay portion of each core; measurement and documentation of the length of the clay and of the sediment portion of each core; photographic documentation of each core; and replacement of each core in the impoundment.

  16. Results of the radiological and chemical characterization of surface impoundments 3539 and 3540 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    Murray, M.E.; Rose, D.A.; Brown, K.S.; Winton, W.; Dean, R.A.; Coe, R.H. III

    1998-03-01

    A radiological and chemical characterization survey of impoundments 3539 and 3540 at the Oak Ridge National Laboratory (ORNL) was conducted during December 1997. Impoundments 3539 and 3540 are located in the Surface Impoundments Operable Unit (SIOU) of Waste Area Group 1. The investigation was performed by the Measurement Applications and Development Group of the Life Sciences Division of ORNL at the request of the Department of Energy (DOE) Office of Environmental Restoration. Sampling was conducted in order to quantify the presence of polychlorinated biphenyls (PCBs), Resource Conservation and Recovery Act (RCRA) constituents, and other contaminants of interest in support of the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) remediation for the SIOU> The survey included collection of sediment/clay samples, quality control blank water samples and equipment rinsate samples for chemical and radiological analysis. Results show the samples contain traces of various organic, inorganic, and radioactive materials. Of particular interest are PCB values which demonstrate the impoundments are not regulated under the Toxic Substances Control Act.

  17. Results of the measurement survey of elevation and environmental media in surface impoundments 3513 (B) and 3524 (A) at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    Murray, M.E.; Rose, D.A.; Brown, K.S.; Coe, R.H.C. III; Lawrence, J.D.; Winton, W.

    1998-07-01

    A measurement survey of the elevation and environmental media in impoundments 3513 (B) and 3524 (A) at the Oak Ridge National Laboratory (ORNL) was conducted during April 1998. The investigation was performed by the Measurement Applications and Development Group of the Life Sciences Division of ORNL at the request of Bechtel Jacobs Company. Measurement activities were conducted at selected locations in order to determine the depth and appearance of the sediment and describe the clay underlying the impoundments prior to remediation. The survey was a follow-up to a previous elevation survey. The survey included the following: collection of sediment/clay cores from selected locations in each impoundment; measurement and documentation of the elevation at the water surface, at the top of sediment, at the top of clay, and at the bottom of each core; visual inspection of each core by a soil scientist to confirm the presence of clay and not material such as fly ash and soda lime compacted over the last 50 years; measurement and documentation of the background beta-gamma radiation level at the time and location of collection of each core, the highest beta-gamma level along the sediment portion of each core, and the highest beta-gamma level along the clay portion of each core; measurement and documentation of the length of the clay and of the sediment portion of each core; photographic documentation of each core; and replacement of each core in the impoundment

  18. Results of the radiological and chemical characterization of surface impoundments 3539 and 3540 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    Murray, M.E.; Rose, D.A.; Brown, K.S.; Winton, W.; Dean, R.A.; Coe, R.H. III

    1998-03-01

    A radiological and chemical characterization survey of impoundments 3539 and 3540 at the Oak Ridge National Laboratory (ORNL) was conducted during December 1997. Impoundments 3539 and 3540 are located in the Surface Impoundments Operable Unit (SIOU) of Waste Area Group 1. The investigation was performed by the Measurement Applications and Development Group of the Life Sciences Division of ORNL at the request of the Department of Energy (DOE) Office of Environmental Restoration. Sampling was conducted in order to quantify the presence of polychlorinated biphenyls (PCBs), Resource Conservation and Recovery Act (RCRA) constituents, and other contaminants of interest in support of the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) remediation for the SIOU> The survey included collection of sediment/clay samples, quality control blank water samples and equipment rinsate samples for chemical and radiological analysis. Results show the samples contain traces of various organic, inorganic, and radioactive materials. Of particular interest are PCB values which demonstrate the impoundments are not regulated under the Toxic Substances Control Act

  19. UAV Remote Sensing Surveillance of a Mine Tailings Impoundment in Sub-Arctic Conditions

    Directory of Open Access Journals (Sweden)

    Anssi Rauhala

    2017-12-01

    Full Text Available Mining typically involves extensive areas where environmental monitoring is spatially sporadic. New remote sensing techniques and platforms such as Structure from Motion (SfM and unmanned aerial vehicles (UAVs may offer one solution for more comprehensive and spatially continuous measurements. We conducted UAV campaigns in three consecutive summers (2015–2017 at a sub-Arctic mining site where production was temporarily suspended. The aim was to monitor a 0.5 km2 tailings impoundment and measure potential subsidence of tailings. SfM photogrammetry was used to produce yearly topographical models of the tailings surface, which allowed the amount of surface displacement between years to be tracked. Ground checkpoints surveyed in stable areas of the impoundment were utilized in assessing the vertical accuracy of the models. Observed surface displacements were linked to a combination of erosion, tailings settlement, and possible compaction of the peat layer underlying the tailings. The accuracy obtained indicated that UAV-assisted monitoring of tailings impoundments is sufficiently accurate for supporting impoundment management operations and for tracking surface displacements in the decimeter range.

  20. River impoundment and sunfish growth

    Science.gov (United States)

    Andrew L. Rypel

    2011-01-01

    Impoundment of rivers by dams is widespread and one of the most devastating anthropogenic impacts to freshwater environments. Linking theoretical and applied research on river impoundment requires an improved capacity for predicting how varying degrees of impoundment affects a range of species. Here, growth of 14 North American sunfish species resilient to river...

  1. The Wireless Sensor Network (WSN) Based Coal Ash Impoundments Safety Monitoring System

    Science.gov (United States)

    Sun, E. J.; Nieto, A.; Zhang, X. K.

    2017-01-01

    Coal ash impoundments are inevitable production of the coal-fired power plants. All coal ash impoundments in North Carolina USA that tested for groundwater contamination are leaking toxic heavy metals and other pollutants. Coal ash impoundments are toxic sources of dangerous pollutants that pose a danger to human and environmental health if the toxins spread to adjacent surface waters and drinking water wells. Coal ash impoundments failures accidents resulted in serious water contamination along with toxic heavy metals. To improve the design and stability of coal ash impoundments, the Development of a Coal Ash Impoundment Safety Monitoring System (CAISM) was proposed based on the implementation of a wireless sensor network (WSN) with the ability to monitor the stability of coal ash impoundments, water level, and saturation levels on-demand and remotely. The monitoring system based on a robust Ad-hoc network could be adapted to different safety conditions.

  2. Dewatering tailings impoundments : interior drains

    International Nuclear Information System (INIS)

    Charlie, W.A.; Doehring, D.O.; Durnford, D.S.

    1984-01-01

    For the design of a new uranium tailings impoundment in the western United States, it was proposed that an interior drainage system be considered to economically and reliably minimize potential short- and long-term environmental impacts. The objectives were to decrease the effective hydraulic head on the clay liner, to dewater and stabilize the tailings, and to increase the amount of water recycled to the mill. In addition, desaturation of the impoundment would induce capillary pressure (negative porewater pressure), further reducing the potential movement of dissolved pollutants. This paper presents saturated and unsaturated seepage principles and reviews the concept, criteria and design of the various interior drainage systems considered

  3. Rehabilitation of uranium tailings impoundments

    International Nuclear Information System (INIS)

    Crawley, A.H.

    1983-01-01

    Under Australian environmental controls relating to the management of uranium tailings, it is no longer acceptable practice to search for a rehabilitation strategy at the end of production when the generation of tailings has ceased. The uranium projects currently in production and those being proposed are tightly regulated by the authorities. The waste management plans must consider site specific factors and must include selection of appropriate disposal sites and design for long term containment. The final encapsulation in engineered facilities must take into account the probable routes to the environment of the tailings. Rehabilitation shoud be undertaken by the mining and milling operators to standards approved by appropriate authorities. Appropriate administrative arrangements are required, by way of technical committees and financial bonds to ensure that agreed standards of rehabilitation may be achieved. Past and present experience with the rehabilitation of uranium tailings impoundments in Australia is discussed

  4. 50 CFR 28.42 - Impounding of domestic animals.

    Science.gov (United States)

    2010-10-01

    ... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Impounding of domestic animals. 28.42... VIOLATIONS OF PARTS 25, 26, AND 27 Impoundment Procedures § 28.42 Impounding of domestic animals. (a) Any animal trespassing on the lands of any national wildlife refuge may be impounded and disposed of in...

  5. Design, permitting, and construction issues associated with closure of the Panna Maria uranium tailings impoundment

    International Nuclear Information System (INIS)

    Strachan, C.L.; Raabe, K.L.

    1997-01-01

    In 1992, Panna Maria Uranium Operations (PMUO) initiated licensing and engineering activities for closure of the Panna Maria mill and 150-acre tailings impoundment located in southeast Texas. Closure of the tailings impoundment is permitted by license amendment through the Texas Natural Resources Conservation Commission (TNRCC), and based on closure criteria outlined in Texas regulations. The closure plan for the Panna Maria tailings impoundment was submitted for Texas regulatory agency review in April 1993, with details of the closure plan modified in 1994, 1995, and 1996. The closure plan included a multi-layered cover over the regraded tailings surface which was designed for long-term isolation of tailings, reduction of radon emanation to regulated levels, and reduction of infiltration to TNRCC-accepted levels. The cover and embankment slope surfaces and surrounding areas were designed to provide acceptable erosional stability as compared to runoff velocities from the Probable Maximum Precipitation event. Cover materials were selected from on-site materials and evaluated for suitability based on permeability, radon attenuation, and soil dispersivity characteristics. Off-site materials were used when necessary. The cover over the tailings has a maximum slope of 0.5 percent, and the regraded embankment slopes outside the perimeter of the impoundment have a maximum slope of 20 percent. All reclaimed slopes are covered with topsoil and revegetated. A riprap-lined channel is to be used to convey runoff from within the perimeter of the reclaimed impoundment to the north of the impoundment

  6. Methodologies for evaluating long-term stabilization designs of uranium mill tailings impoundments

    International Nuclear Information System (INIS)

    Nelson, J.D.; Abt, S.R.; Volpe, R.L.; Van Zye, D.; Hinkle, N.E.; Staub, W.P.

    1986-06-01

    Uranium mill tailings impoundments require long-term (200 to 1000 years) stabilization. This report reviews currently available methodologies for evaluating factors that can have a significant influence on tailings stabilization and develops methodologies in technical areas where none presently exist. Mill operators can use these methodologies to assist with (1) the selection of sites for mill tailings impoundments, (2) the design of stable impoundments, and (3) the development of reclamation plans for existing impoundments. These methodologies would also be useful for regulatory agency evaluations of proposals in permit or license applications. Methodologies were reviewed or developed in the following technical areas: (1) prediction of the Probable Maximum Precipitation (PMP) and an accompanying Probable Maximum Flood (PMF); (2) prediction of the stability of local and regional fluvial systems; (3) design of impoundment surfaces resistant to gully erosion; (4) evaluation of the potential for surface sheet erosion; (5) design of riprap for protecting embankments from channel flood flow and overland flow; (6) selection of riprap with appropriate durability for its intended use; and (7) evaluation of oversizing required for marginal quality riprap

  7. Artificial ocean upwelling utilizing the energy of surface waves

    Science.gov (United States)

    Soloviev, Alexander

    2016-04-01

    Artificial upwelling can bring cold water from below the thermocline to the sea surface. Vershinsky, Pshenichnyy, and Soloviev (1987) developed a prototype device, utilizing the energy of surface waves to create an upward flow of water in the tube. This is a wave-inertia pump consisting of a vertical tube, a valve, and a buoy to keep the device afloat. An outlet valve at the top of the unit synchronizes the operation of the device with surface waves and prevents back-splashing. A single device with a 100 m long and 1.2 m diameter tube is able to produce up to 1 m3s-1 flow of deep water to the surface. With a 10 oC temperature difference over 100 m depth, the negative heat supply rate to the sea surface is 42 MW, which is equivalent to a 42 Wm-2 heat flux, if distributed over 1 km2 area. Such flux is comparable to the average net air-sea flux. A system of artificial upwelling devices can cool down the sea surface, modify climate on a regional scale and possibly help mitigate hurricanes. The cold water brought from a deeper layer, however, has a larger density than the surface water and therefore has a tendency to sink back down. In this work, the efficiency of wave-inertia pumps and climatic consequences are estimated for different environmental conditions using a computational fluid dynamics model.

  8. 36 CFR 262.11 - Impounding of dogs.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Impounding of dogs. 262.11... ENFORCEMENT SUPPORT ACTIVITIES Impoundments and Removals § 262.11 Impounding of dogs. Any dog found running at large in a part of the National Forest System, which has been closed to dogs running at large, may be...

  9. Distribution and migration of pesticide residues in mosquito control impoundments St. Lucie County, Florida, USA

    Science.gov (United States)

    Parkinson, R. W.; Wang, T. C.; White, J. R.; David, J. R.; Hoffman, M. E.

    1993-09-01

    This project was designed to: (1) document the distribution and migration of organochlorine pesticide residues within marsh substrates of 18 St. Lucie County mosquito control impoundments located along the Indian River Lagoon estuary, and (2) evaluate the impact of water management techniques on residue mobility. Our results indicate that detectible concentrations of organochlorine compounds, applied between the late 1940s and early 1950s, are present in 16 of the 18 St. Lucie County mosquito control impoundments. These compounds are primarily restricted to the surficial, organic-rich wetland sediment, which, based upon geotechnical analysis, was exposed to the atmosphere at a time when the impoundments were subjected to pesticide treatment. Contaminated sediments are present below the surficial, organic-rich layer, suggesting that some vertical migration of pesticides has occurred. It is unlikely that leaching associated with the downward percolation of impounded water was responsible for this migration as pesticide residues were never detected within the in situ pore waters. An alternative explanation is that biological processes (e.g., rooting, burrowing) facilitated the downward flux of organochlorine compounds into sediment horizons not subjected to direct treatment. Eighty-eight surface water samples obtained from two impoundments subjected to contrasting water management techniques were analyzed for pesticide content. None of the surficial water samples collected in association with these impoundments contained detectible concentrations of organochlorine compounds. These samples were unfiltered and contained as much as 25 mg/1 of particulate organic matter. This suggests that the currently preferred management technique (RIM), which is designed to maintain water quality, limit mosquito production, and provide for ecological continuity, does not hydraulically mobilize pesticide residues into the Indian River Lagoon estuary.

  10. The Role of Small Impoundments on Flow Alteration Within River Networks

    Science.gov (United States)

    Brogan, C. O.; Keys, T.; Scott, D.; Burgholzer, R.; Kleiner, J.

    2017-12-01

    Numerous water quality and quantity models have been established to illustrate the ecologic and hydrologic effects of large reservoirs. Smaller, unregulated ponds are often assumed to have a negligible impact on watershed flow regimes even though they overwhelmingly outnumber larger waterbodies. Individually, these small impoundments impart merely a fraction of the flow alteration larger reservoirs do; however, a network of ponds may act cumulatively to alter the flow regime. Many models have attempted to study smaller impoundments but rely on selectively available rating curves or bathymetry surveys. This study created a generalized process to model impoundments of varying size across a 58 square mile watershed exclusively using satellite imagery and publicly available information as inputs. With information drawn from public Army Corps of Engineers databases and LiDAR surveys, it was found that impoundment surface and drainage area served as useful explanatory variables, capable of predicting both pond bathymetry and outlet structure area across the 37 waterbodies modeled within the study area. Working within a flow routing model with inputs from the Chesapeake Bay HSPF model and verified with USGS gauge data, flow simulations were conducted with increasing number of impoundments to quantify how small ponds affect the overall flow regime. As the total impounded volume increased, simulations showed a notable reduction in both low and peak flows. Medium-sized floods increased as the network of ponds and reservoirs stabilized the catchment's streamflow. The results of this study illustrate the importance of including ponded waters into river corridor models to improve downstream management of both water quantity and quality.

  11. A novel ultrasonic surface machining tool utilizing elastic traveling waves.

    Science.gov (United States)

    Ji, Ruinan; Jin, Jiamei; Wang, Liang; Zhang, Jianhui

    2017-09-01

    With the rapid development of modern industrial technology and high performance technology products, ultra-precision machining technology becomes increasingly important. However, joint clearance of kinematic pairs, lack of feeding accuracy and overlarge contact stress still limit the further improvement of ultra-precision machining technology. In this study, a novel surface machining method utilizing structural elastic waves was proposed, and a machining tool using the piezoelectric actuating principle was presented for verifying the proposed method. Two vibration modes with a phase shift of π/2 in both space and time domains are exited simultaneously in the elliptical motion of points on the structural surface. By means of adjusting driving signal parameters, such as frequency, voltage amplitude and phase shift, different machining performances could be achieved. The configuration and working vibration modes of the proposed machining tool were firstly calculated by the finite element method, and then the optimal working frequency of the machining tool prototype was determined by vibration characteristic experiments. At last, machining characteristic experiments were conducted to validate the proposed machining method. Experimental results showed that the minimum working contact force between the machining tool and workpiece was 1N, and the chipped depth of 1.93μm was achieved at the same contact force after machining for 5min. And at the conditions of the contact force of 6N, two driving voltages of 400V pp with a phase shift of π/2, and machining time of 5min, the prototype could achieve to machine the workpiece most efficiently and the roughness of the machined workpiece surface could be reached approximating 0.20μm. In conclusion, this proposed machining method could achieve a good quality machined surface with low residual stress and little damage by applying low contact force. Furthermore, it also had the advantage of no joint clearance error due to no

  12. Implementation of solar-reflective surfaces: Materials and utility programs

    Energy Technology Data Exchange (ETDEWEB)

    Bretz, S.; Akbari, H.; Rosenfeld, A.; Taha, H.

    1992-06-01

    This report focuses on implementation issues for using solar-reflective surfaces to cool urban heat islands, with specific examples for Sacramento, California. Advantages of solar-reflective surfaces for reducing energy use are: (1) they are cost-effective if albedo is increased during routine maintenance; (2) the energy savings coincide with peak demand for power; (3) there are positive effects on environmental quality; and (4) the white materials have a long service life. Important considerations when choosing materials for mitigating heat islands are identified as albedo, emissivity, durability, cost, pollution and appearance. There is a potential for increasing urban albedo in Sacramento by an additional 18%. Of residential roofs, we estimate that asphalt shingle and modified bitumen cover the largest area, and that built-up roofing and modified bitumen cover the largest area of commercial buildings. For all of these roof types, albedo may be increased at the time of re-roofing without any additional cost. When a roof is repaired, a solar-reflective roof coating may be applied to significantly increase albedo and extend the life of the root Although a coating may be cost-effective if applied to a new roof following installation or to an older roof following repair, it is not cost-effective if the coating is applied only to save energy. Solar-reflective pavement may be cost-effective if the albedo change is included in the routine resurfacing schedule. Cost-effective options for producing light-colored pavement may include: (1) asphalt concrete, if white aggregate is locally available; (2) concrete overlays; and (3) newly developed white binders and aggregate. Another option may be hot-rolled asphalt, with white chippings. Utilities could promote solar-reflective surfaces through advertisement, educational programs and cost-sharing of road resurfacing.

  13. Evaluation of Co and Cr mobility in soil profiles collected in a scrapyard of impounded vehicles

    International Nuclear Information System (INIS)

    Lange, Camila N.; Figueiredo, Ana Maria G.; Enzweiler, Jacinta

    2015-01-01

    The number of motor vehicles in urban environments has increased dramatically in the past years. As a result, so has the number of impounded and end-of-life vehicles. Car wastes can have a very high metal content, which can cause important environmental impacts to the soil where these vehicles are kept. Most Brazilian vehicle impound scrapyards are currently operating at their maximum capacity and soils may have become contaminated by past or current vehicle handling practices. Most of these areas do not present an impermeable surface. The level of soil contamination with heavy metals depends on the type of soil, climate and management practices. Metals, such as Co and Cr, that are present in many auto-parts, may be considered potentially toxic elements in these areas. The aim of this study was to evaluate Co and Cr levels and behavior in soil profiles located in a scrapyard of impounded vehicles of Ribeirao Pires-SP city. For this purpose, samples from distinct horizons of three soil profiles were collected. Element concentrations were determined by Instrumental Neutron Activation Analysis (INAA). Soil parameters such as pH, organic matter content and clay, silt and sand percentage were also determined. The obtained data were statistically analyzed in order to establish correlations between elemental concentrations and the impounded vehicles scrapyard soil. Soil acidity showed to be the most remarkable property for Cr and Co mobility through soil profile. (author)

  14. Application of carbon isotopes to detect seepage out of coalbed natural gas produced water impoundments

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Shikha, E-mail: shikha.sharma@mail.wvu.edu [Department of Geology and Geography, West Virginia University, Morgantown, WV 26506 (United States); Baggett, Joshua K. [Department of Ecosystem Science and Management, Texas A and M University, College Station, 77843 2126 (United States)

    2011-08-15

    Highlights: > Coalbed natural gas extraction results in large amount of produced water. > Risk of deterioration of ambient water quality. > Carbon isotope natural tracer for detecting seepage from produced water impoundments. - Abstract: Coalbed natural gas (CBNG) production from coal bed aquifers requires large volumes of produced water to be pumped from the subsurface. The produced water ranges from high quality that meets state and federal drinking water standards to low quality due to increased salinity and/or sodicity. The Powder River Basin of northeastern Wyoming is a major coalbed natural gas producing region, where water quality generally decreases moving from the southeastern portion of the basin towards the center. Most produced water in Wyoming is disposed into impoundments and other surface drainages, where it may infiltrate into shallow groundwater. Groundwater degradation caused by infiltration of CBNG produced water holding impoundments into arid, soluble salt-rich soils is an issue of immense importance because groundwater is a major source for stock water, irrigation, and drinking water for many small communities in these areas. This study examines the potential of using stable C isotope signatures of dissolved inorganic C ({delta}{sup 13}C{sub DIC}) to track the fate of CBNG produced water after it is discharged into the impoundments. Other geochemical proxies like the major cations and major anions were used in conjunction with field water quality measurements to understand the geochemical differences between CBNG produced waters and ambient waters in the study area. Samples were collected from the CBNG discharge outfalls, produced water holding impoundments, and monitoring wells from different parts of the Powder River Basin and analyzed for {delta}{sup 13}C{sub DIC}. The CBNG produced waters from outfalls and impoundments have positive {delta}{sup 13}C{sub DIC} values that fall within the range of +12 per mille to +22 per mille, distinct from

  15. Swarm formation control utilizing elliptical surfaces and limiting functions.

    Science.gov (United States)

    Barnes, Laura E; Fields, Mary Anne; Valavanis, Kimon P

    2009-12-01

    In this paper, we present a strategy for organizing swarms of unmanned vehicles into a formation by utilizing artificial potential fields that were generated from normal and sigmoid functions. These functions construct the surface on which swarm members travel, controlling the overall swarm geometry and the individual member spacing. Nonlinear limiting functions are defined to provide tighter swarm control by modifying and adjusting a set of control variables that force the swarm to behave according to set constraints, formation, and member spacing. The artificial potential functions and limiting functions are combined to control swarm formation, orientation, and swarm movement as a whole. Parameters are chosen based on desired formation and user-defined constraints. This approach is computationally efficient and scales well to different swarm sizes, to heterogeneous systems, and to both centralized and decentralized swarm models. Simulation results are presented for a swarm of 10 and 40 robots that follow circle, ellipse, and wedge formations. Experimental results are included to demonstrate the applicability of the approach on a swarm of four custom-built unmanned ground vehicles (UGVs).

  16. Infiltration from an impoundment for coal-bed natural gas, Powder River Basin, Wyoming: Evolution of water and sediment chemistry

    Science.gov (United States)

    Healy, R.W.; Rice, C.A.; Bartos, T.T.; McKinley, M.P.

    2008-01-01

    Development of coal-bed natural gas (CBNG) in the Powder River Basin, Wyoming, has increased substantially in recent years. Among environmental concerns associated with this development is the fate of groundwater removed with the gas. A preferred water-management option is storage in surface impoundments. As of January 2007, permits for more than 4000 impoundments had been issued within Wyoming. A study was conducted on changes in water and sediment chemistry as water from an impoundment infiltrated the subsurface. Sediment cores were collected prior to operation of the impoundment and after its closure and reclamation. Suction lysimeters were used to collect water samples from beneath the impoundment. Large amounts of chloride (12,300 kg) and nitrate (13,500 kg as N), most of which accumulated naturally in the sediments over thousands of years, were released into groundwater by infiltrating water. Nitrate was more readily flushed from the sediments than chloride. If sediments at other impoundment locations contain similar amounts of chloride and nitrate, impoundments already permitted could release over 48 x 106 kg of chloride and 52 x 106 kg of nitrate into groundwater in the basin. A solute plume with total dissolved solid (TDS) concentrations at times exceeding 100,000 mg/L was created in the subsurface. TDS concentrations in the plume were substantially greater than those in the CBNG water (about 2300 mg/L) and in the ambient shallow groundwater (about 8000 mg/L). Sulfate, sodium, and magnesium are the dominant ions in the plume. The elevated concentrations are attributed to cation-exchange-enhanced gypsum dissolution. As gypsum dissolves, calcium goes into solution and is exchanged for sodium and magnesium on clays. Removal of calcium from solution allows further gypsum dissolution.

  17. 32 CFR 634.53 - Disposition of vehicles after impoundment.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Disposition of vehicles after impoundment. 634.53 Section 634.53 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) LAW ENFORCEMENT AND CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION Impounding Privately Owned Vehicles...

  18. 32 CFR 634.51 - Procedures for impoundment.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Procedures for impoundment. 634.51 Section 634.51 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) LAW ENFORCEMENT AND CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION Impounding Privately Owned Vehicles § 634.51...

  19. Sediment quality in freshwater impoundments at Savannah National Wildlife Refuge

    Science.gov (United States)

    Winger, P.V.; Lasier, P.J.

    2004-01-01

    Freshwater impoundments at Savannah National Wildlife Refuge (NWR), South Carolina, provide an important habitat for wildlife species, but degraded sediment quality in the Savannah River downstream of the discharge from two impoundments have caused concern about potential contaminant problems within the impoundments. The quality of sediments from five impoundments (impoundments no. 1, 2, 6, 7, and 17) on the NWR was evaluated using physical and chemical characterization, contaminant concentrations (metals, organochlorine pesticides, polychlorinated biphenyls, and polycyclic aromatic hydrocarbons), and toxicity testing. Survival of Hyalella azteca (freshwater amphipod) exposed for 28 days to solid-phase sediments was not significantly different from controls, but growth was significantly decreased at several sites. Survival in 96-hour exposures to sediment pore water was significantly decreased at most sites. Factors contributing to the toxic responses were low pH (3.7 to 4.1), ammonia (20 mg/L), and increased concentrations of cations in the pore water. The excess of simultaneously extracted metals over the acid volatile sulfides in the sediments was also typical of sites displaying decreased sediment quality. Elemental concentrations in pore water were negatively correlated with pH, and the highest concentrations were observed in impoundment no. 7. The acidic nature of the sediment in this impoundment was exacerbated by recent draining, burning, and disking, which allowed oxidation of the previously anoxic wetland sediment. Sediment disturbance and mixing of vegetation into the sediments by disking may also have contributed to the formation of ammonia caused by microbial decomposition of the fragmented organic matter. Contaminants were not detected in sediments from the impoundments, but releases of acidic water with increased levels of sediment cations from the impoundments may have contributed to the degraded sediment conditions previously observed in the river

  20. Responsiveness summary for the engineering evaluation/cost analysis for the proposed management of contaminated water impounded at the Weldon Spring Chemical Plant Area

    International Nuclear Information System (INIS)

    Maxey, M.L.; MacDonell, M.M.; Peterson, J.M.

    1991-01-01

    The US Department of Energy (DOE) issued the Engineering Evaluation/Cost Analysis for the Proposed Management of Contaminated Water Impounded at the Weldon Spring Chemical Plant Area in July 1990. The engineering evaluation/cost analysis (EE/CA) examines various alternatives for the proposed action to manage contaminated surface water impounded at the chemical plant area. The primary objective is to minimize potential migration of contaminants from surface impoundments to the local environment. The EE/CA addresses water currently impounded in four waste raffinate pits and two small ponds and water that will be impounded in the future as a result of upcoming response actions. Radioactive and chemical contaminants are migrating from the currently impounded water to underlying on-site groundwater via seepage and to off-site surface water via runoff. The treatment process and facilities that will be provided for management of currently impounded water can subsequently be used to manage other contaminated water in the future. Based on the evaluation of various alternatives in the EE/CA, DOE determined that the best approach for managing surface water impounded at the chemical plant area would be to remove contaminants from the water and release the treatment water to the Missouri River via a natural drainage channel. To establish requirements for releasing this treated water, DOE applied for a modification to its existing discharge permit from the Missouri Department of Natural Resources (DNR) under the National Pollutant Discharge Elimination System (NPDES) program. The EE/CA provided a major source of technical input to the application for modifying the permit. This responsiveness summary has been prepared to address the major issues identified in oral and written comments on the proposed action. 1 tab

  1. Potential utility of the thematic mapper for surface mine monitoring

    International Nuclear Information System (INIS)

    Irons, J.R.; Lachowski, H.M.

    1981-01-01

    One of many potential applications of the thematic mapper (TM) is surface mine monitoring. To assess this potential, data acquired by an aircraft multispectral scanner over Pennsylvania surface mines were preprocessed to simulate the anticipated spectral, spatial, and radiometric characteristics of TM data. False color imagery and thematic maps were derived from the simulated data and compared to imagery and maps derived from LANDSAT multispectral scanner subsystems data. On the basis of this comparison, TM data should definitely increase the detail and accuracy of remotely acquired surface mine information and may enable the remote determination of compliance with reclamation regulations

  2. Utilization of surface-treated rubber particles from waste tires

    Energy Technology Data Exchange (ETDEWEB)

    Smith, F.G. [Argonne National Lab., IL (United States). Energy Systems Div.]|[Environmental Technologies Alternatives, Inc., Lima, OH (United States)

    1994-12-01

    During a 12-month program, the author successfully demonstrated commercial applications for surface-treated rubber particles in two major markets: footwear (shoe soles and components) and urethane-foam carpet underlay (padding). In these markets, he has clearly demonstrated the ease of using R-4080 and R-4030 surface-treated rubber particles in existing manufacturing plants and processes and have shown that the material meets or exceeds existing standards for performance, quality, and cost-effectiveness. To produce R-4080 and R-4030, vulcanized rubber, whole-tire material is finely ground to particles of nominal 80 and mesh size respectively. Surface treatment is achieved by reacting these rubber particles with chlorine gas. In this report, the author describes the actual test and evaluations of the participant companies, and identifies other potential end uses.

  3. Integrated Optical Components Utilizing Long-Range Surface Plasmon Polaritons

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra; Nikolajsen, Thomas; Leosson, Kristjan

    2005-01-01

    New optical waveguide technology for integrated optics, based on propagation of long-range surface plasmon polaritons (LR-SPPs) along metal stripes embedded in dielectric, is presented. Guiding and routing of electromagnetic radiation along nanometer-thin and micrometer-wide gold stripes embedded...

  4. The utilization of the response surface methodology for the ...

    African Journals Online (AJOL)

    SERVER

    2007-12-03

    Dec 3, 2007 ... Drojdiile ca aliment-medicament. In: Anghel I (ed). Biologia si Tehnologia Drojdiilor, vol 2, Editura Tehnica, Bucharest. Shieh CJ, Liao HF, Lee CC (2003). Optimization of lipase-catalyzed biodiesel by response surface methodology, Bioresour. Technol. 88: 103-106. Smigelschi O, Woinarovschy A (1978).

  5. The utilization of the response surface methodology for the ...

    African Journals Online (AJOL)

    A mutant strain of the yeast Saccharomyces cerevisiae growing on ethanol as single source of carbon and energy was used in optimization experiments at laboratory and micropilot scale, following the surface response methodology. The cultivation medium optimization was performed on the basis of maximization of dry cell ...

  6. Eddy current analysis by BEM utilizing loop electric and surface magnetic currents as unknowns

    International Nuclear Information System (INIS)

    Ishibashi, Kazuhisa

    2002-01-01

    The surface integral equations whose unknowns are the surface electric and magnetic currents are widely used in eddy current analysis. However, when the skin depth is thick, computational error is increased especially in obtaining electromagnetic fields near the edge of the conductor. In order to obtain the electromagnetic field accurately, we propose an approach to solve surface integral equations utilizing loop electric and surface magnetic currents as unknowns. (Author)

  7. Standardization of surface electromyography utilized to evaluate patients with dysphagia

    Directory of Open Access Journals (Sweden)

    Vaiman Michael

    2007-06-01

    Full Text Available Abstract Backgorund Patients suspected of having swallowing disorders, could highly benefit from simple diagnostic screening before being referred to specialist evaluations. We introduce surface electromyography (sEMG to carry out rapid assessment of such patients and propose suggestions for standardizing sEMGs in order to identify abnormal deglutition. Methods Specifics steps for establishing standards for applying the technique for screening purposes (e.g., evaluation of specific muscles, the requirements for diagnostic sEMG equipment, the sEMG technique itself, and defining the tests suitable for assessing deglutition (e.g., saliva, normal, and excessive swallows and uninterrupted drinking of water are presented in detail. A previously described normative database for single swallowing and drinking and standard approach to analysis was compared to data on the duration and electric activity of muscles involved in deglutition and with sEMG recordings in order to estimate stages of a swallow. Conclusion SEMG of swallowing is a simple and reliable method for screening and preliminary differentiation among dysphagia and odynophagia of various origins. This noninvasive radiation-free examination has a low level of discomfort, and is simple, timesaving and inexpensive to perform. With standardization of the technique and an established normative database, sEMG can serve as a reliable screening method for optimal patient management.

  8. French Modular Impoundment: Final Cost and Performance Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Drown, Peter [French Development Enterprises, LLC, North Billerica, MA (United States); French, Bill [French Development Enterprises, LLC, North Billerica, MA (United States)

    2017-05-17

    This report comprises the Final Cost and Performance Report for the Department of Energy Award # EE0007244, the French Modular Impoundment (aka the “French Dam”.) The French Dam is a system of applying precast modular construction to water control structures. The “French Dam” is a term used to cover the construction means/methods used to construct or rehabilitate dams, diversion structures, powerhouses, and other hydraulic structures which impound water and are covered under FDE’s existing IP (Patents # US8414223B2; US9103084B2.)

  9. A model for evaluating effects of climate, water availability, and water management on wetland impoundments--a case study on Bowdoin, Long Lake, and Sand Lake National Wildlife Refuges

    Science.gov (United States)

    Tangen, Brian A.; Gleason, Robert A.; Stamm, John F.

    2013-01-01

    Many wetland impoundments managed by the U.S. Fish and Wildlife Service (USFWS) National Wildlife Refuge System throughout the northern Great Plains rely on rivers as a primary water source. A large number of these impoundments currently are being stressed from changes in water supplies and quality, and these problems are forecast to worsen because of projected changes to climate and land use. For example, many managed wetlands in arid regions have become degraded owing to the long-term accumulation of salts and increased salinity associated with evapotranspiration. A primary goal of the USFWS is to provide aquatic habitats for a diversity of waterbirds; thus, wetland managers would benefit from a tool that facilitates evaluation of wetland habitat quality in response to current and anticipated impacts of altered hydrology and salt balances caused by factors such as climate change, water availability, and management actions. A spreadsheet model that simulates the overall water and salinity balance (WSB model) of managed wetland impoundments is presented. The WSB model depicts various habitat metrics, such as water depth, salinity, and surface areas (inundated, dry), which can be used to evaluate alternative management actions under various water-availability and climate scenarios. The WSB model uses widely available spreadsheet software, is relatively simple to use, relies on widely available inputs, and is readily adaptable to specific locations. The WSB model was validated using data from three National Wildlife Refuges with direct and indirect connections to water resources associated with rivers, and common data limitations are highlighted. The WSB model also was used to conduct simulations based on hypothetical climate and management scenarios to demonstrate the utility of the model for evaluating alternative management strategies and climate futures. The WSB model worked well across a range of National Wildlife Refuges and could be a valuable tool for USFWS

  10. Effect of weir impoundments on methane dynamics in a river

    Czech Academy of Sciences Publication Activity Database

    Bednařík, A.; Blaser, M.; Matoušů, Anna; Hekera, P.; Rulík, M.

    2017-01-01

    Roč. 584, April (2017), s. 164-174 ISSN 0048-9697 R&D Projects: GA ČR(CZ) GA13-00243S Institutional support: RVO:60077344 Keywords : methane production * methane emission * methane ebullition * river impoundment * river sediment Subject RIV: DA - Hydrology ; Limnology OBOR OECD: Marine biology, freshwater biology, limnology Impact factor: 4.900, year: 2016

  11. 32 CFR 634.23 - Specified consent to impoundment.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Specified consent to impoundment. 634.23 Section 634.23 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) LAW ENFORCEMENT AND CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION Motor Vehicle Registration § 634.23...

  12. Propagation of a cadmium spill through an impounded river system

    NARCIS (Netherlands)

    Klaver, G.T.; Joziasse, J.; Bakker, I.

    2009-01-01

    In this paper, the influence of impoundments (sluices, weirs, etc.) and stream components (tributaries, river branches, associated canals) on the metal content in water and suspended particulate matter (SPM) in the Dutch part of the River Meuse is assessed using the decrease in the cadmium content

  13. Interfacial stability of soil covers on lined surface impoundments

    International Nuclear Information System (INIS)

    Mitchell, D.H.; Gates, T.E.

    1986-04-01

    The factors affecting the interfacial stability of soil covers on geomembranes were examined to determine the maximum stable slopes for soil cover/geomembrane systems. Several instances of instability of soil covers on geomembranes have occurred at tailings ponds, leaving exposed geomembranes with the potential for physical ddamage and possibly chemical and ultraviolet degradation. From an operator's viewpoint, it is desirable to maximize the slope of lined facilities in order to maximize the volume-to-area ratio; however, the likelihood for instability also increases with increasing slope. Frictional data obtained from direct shear tests are compared with stability data obtained using a nine-square-meter (m 2 ) engineering-scale test stand to verify that direct shear test data are valid in slope design calculations. Interfacial frictional data from direct shear tests using high-density polyethylene and a poorly graded sand cover agree within several degrees with the engineering-scale tests. Additional tests with other soils and geomembranes are planned. The instability of soil covers is not always an interfacial problem; soil erosion and limited drainage capacity are additional factors that must be considered in the design of covered slopes. 7 refs., 5 figs., 2 tabs

  14. 40 CFR 264.1085 - Standards: Surface impoundments.

    Science.gov (United States)

    2010-07-01

    ... materials of construction and designing the cover and closure devices shall include: Organic vapor... closure device in the closed position, as applicable. (B) To remove accumulated sludge or other residues... construction and designing the cover and closure devices shall include: Organic vapor permeability; the effects...

  15. 40 CFR 265.1086 - Standards: Surface impoundments.

    Science.gov (United States)

    2010-07-01

    ... materials of construction and designing the cover and closure devices shall include: Organic vapor... closure device in the closed position, as applicable. (B) To remove accumulated sludge or other residues... construction and designing the cover and closure devices shall include: Organic vapor permeability; the effects...

  16. Engineering evaluation/cost analysis for the proposed management of contaminated water impounded at the Weldon Spring chemical plant area

    International Nuclear Information System (INIS)

    MacDonell, M.M.; Maxey, M.L.; Peterson, J.M.; Joya, I.E.

    1990-07-01

    This engineering evaluation/cost analysis (EE/CA) report has been prepared to support the proposed removal action for managing contaminated surface waters impounded at the chemical plant area of the Weldon Spring site, located near Weldon Spring, Missouri. The US Department of Energy is responsible for cleanup activities at the site under its Surplus Facilities Management Program (SFMP). The major goals of SFMP are to eliminate potential hazards to human health and the environment that are associated with contamination at SFMP sites and to make surplus real property available for other uses, to the extent possible. The objectives of this EE/CA report are to identify the cleanup as a removal action, document the selection of a response that will mitigate the potential release of radioactive or chemical contaminants from the impounded waters into the nearby environment, and address environmental impacts associated with the proposed action. 41 refs., 8 figs., 8 tabs

  17. Methods and energy storage devices utilizing electrolytes having surface-smoothing additives

    Science.gov (United States)

    Xu, Wu; Zhang, Jiguang; Graff, Gordon L; Chen, Xilin; Ding, Fei

    2015-11-12

    Electrodeposition and energy storage devices utilizing an electrolyte having a surface-smoothing additive can result in self-healing, instead of self-amplification, of initial protuberant tips that give rise to roughness and/or dendrite formation on the substrate and anode surface. For electrodeposition of a first metal (M1) on a substrate or anode from one or more cations of M1 in an electrolyte solution, the electrolyte solution is characterized by a surface-smoothing additive containing cations of a second metal (M2), wherein cations of M2 have an effective electrochemical reduction potential in the solution lower than that of the cations of M1.

  18. Utilization of textile surface covers for stabilizing slopes in brown coal surface mines

    Energy Technology Data Exchange (ETDEWEB)

    Rathmann, K.; Ganz, R.; Taubert, E.; Scheler, D.

    1980-01-01

    Results are presented of tests on preventing slope erosion at a spoil bank by covering inclined surfaces with textile. Three polyethylene and one polyamide cloth types with varying mesh size and material elasticity were attached to the ground after seeding of grass plants. Slope erosion and grass growth were evaluated at three-week intervals. Best results were achieved with polyethylene cloth with a 10/20 mm mesh to facilitate grass growth and with low elasticity, which showed the best adaption to the slope of the ground and prevented washout from below. Economic advantages of using surface covers are described as reducing expenditures in labor employed in slope maintenance. A 50% cost saving is estimated, which depends on the availability of low cost ground covers, preferably from waste products. The suitability of textile from magnetic tape scrap will be tested.

  19. Assessment of sediments in the riverine impoundments of national wildlife refuges in the Souris River Basin, North Dakota

    Science.gov (United States)

    Tangen, Brian A.; Laubhan, Murray K.; Gleason, Robert A.

    2014-01-01

    Accelerated sedimentation of reservoirs and riverine impoundments is a major concern throughout the United States. Sediments not only fill impoundments and reduce their effective life span, but they can reduce water quality by increasing turbidity and introducing harmful chemical constituents such as heavy metals, toxic elements, and nutrients. U.S. Fish and Wildlife Service national wildlife refuges in the north-central part of the United States have documented high amounts of sediment accretion in some wetlands that could negatively affect important aquatic habitats for migratory birds and other wetland-dependent wildlife. Therefore, information pertaining to sediment accumulation in refuge impoundments potentially is important to guide conservation planning, including future management actions of individual impoundments. Lands comprising Des Lacs, Upper Souris, and J. Clark Salyer National Wildlife Refuges, collectively known as the Souris River Basin refuges, encompass reaches of the Des Lacs and Souris Rivers of northwestern North Dakota. The riverine impoundments of the Souris River Basin refuges are vulnerable to sedimentation because of the construction of in-stream dams that interrupt and slow river flows and because of post-European settlement land-use changes that have increased the potential for soil erosion and transport to rivers. Information regarding sediments does not exist for these refuges, and U.S. Fish and Wildlife Service personnel have expressed interest in assessing refuge impoundments to support refuge management decisions. Sediment cores and surface sediment samples were collected from impoundments within Des Lacs, Upper Souris, and J. Clark Salyer National Wildlife Refuges during 2004–05. Cores were used to estimate sediment accretion rates using radioisotope (cesium-137 [137Cs], lead-210 [210Pb]) dating techniques. Sediment cores and surface samples were analyzed for a suite of elements and agrichemicals, respectively. Examination of

  20. Stochastic Modelling of the Hydraulic Anisotropy of Ash Impoundment Sediment

    Science.gov (United States)

    Slávik, Ivan

    2017-12-01

    In the case reported here the impoundments of a 400 MW coal heated power plant with an annual production of about 1.5 million tons of fuel ash are of the cross-valley type, operated by the simple and cheap „upstream method”. The aim of the research was to determine overall and local values of the permeability in horizontal as well as in vertical direction and the anisotropy of the thin-layered sedimented ash. The coal ashes are hydraulically transported through pipelines in form of a slurry and periodically floated on the beach of the impoundment. The ashes are deposited in the form of a thin-layered sediment, with random alternation of layers with a coarser or finer granularity. The ash impoundment sediment is anthropogenic sediment with horizontally laminated texture. Therefore, the sediment is anisotropic from the viewpoint of water seepage. The knowledge of the permeability and the seepage anisotropy of the sediment is a basic requirement for the design of an appropriate dewatering system. The seepage anisotropy of the ash sediment has been checked by means of stochastic modelling, based on the correlation between the effective grain diameter and the coefficient of permeability of the ash: the effective grain diameter and the thickness of individual layers have been proposed to be random events.

  1. A risk assessment of water salinization during the initial impounding period of a proposed reservoir in Tianjin, China.

    Science.gov (United States)

    Zhu, Liqin; Jiang, Cuiling; Wang, Youheng; Peng, Yanmei; Zhang, Peng

    2013-09-01

    Water salinization of coastal reservoirs seriously threatens the safety of their water supply. To elucidate the mechanism of salinization and to quantitatively analyze the risk in the initial period of the impoundment of a proposed reservoir in Tianjin Binhai New Area, laboratory and field simulation experiments were implemented and integrated with the actual operation of Beitang Reservoir, which is located in the same region and has been operational for many years. The results suggested that water salinization of the proposed reservoir was mainly governed by soil saline release, evaporation and leakage. Saline release was the prevailing factor in the earlier stage of the impoundment, then the evaporation and leakage effects gradually became notable over time. By referring to the actual case of Beitang Reservoir, it was predicted that the chloride ion (Cl(-)) concentration of the water during the initial impounding period of the proposed reservoir would exceed the standard for quality of drinking water from surface water sources (250 mg L(-1)), and that the proposed reservoir had a high risk of water salinization.

  2. Investigation, assessment and remediation of the water pathway in the surroundings of the Culmitzsch A tailings impoundment

    International Nuclear Information System (INIS)

    Schulze, G.; Paul, M.; Priester, J.; Schoepfer, C.

    1998-01-01

    Several large tailings impoundments in Saxony and Thuringia are the result of the extensive uranium mining and milling in Eastern Germany after World War II. The Culmitzsch tailings pond in Eastern Thuringia was constructed within a former uranium open pit mine and is located within the Culmitzsch trench fault. The tailings impoundment includes two ponds (Culmitzsch A and B) which are separated by an internal dam with an impervious core. The Culmitzsch A pond covers an area of 158 ha, the maximum tailings thickness is 70 m. Between this pond (elevation of up to 340 m above sea-level) and the Lerchenbach creek (265.. 280 m above sea-level) a steep gradient exists. So the valley of the Lerchenbach is the general discharge area for the seepage of the pond which is a result of dewatering by gravity and consolidation. The seepage water migrates through the southern dam of the impoundment and through permeable layers which are in contact with the tailings. About 400 groundwater wells were installed within three aquifers in order to clarify the flow direction and the degree of contamination of the groundwater as well as to investigate the geohydraulic properties of the rocks in the surroundings of the pond. Based on the results of this investigation programme a three-dimensional hydrogeological model was built up which reflects the general relationships between the pond and its geological setting as well as the water balance of the whole system. Presently a catchment system exists which gathers all surface waters with significant uranium and salt concentrations. Moreover dewatering wells on the beach zone of the pond and catchment wells in the downstream area of the impoundment have been installed. Before being released to the receiving streams seepage and freewater are treated in a two-step water treatment plant in order to decrease their uranium, radium and arsenic contents. (orig.) [de

  3. Impact of Utilizing Photos and Deimos as Waypoints for Mars Human Surface Missions

    Science.gov (United States)

    Cianciolo, Alicia D.; Brown, Kendall

    2015-01-01

    Phobos and Deimos, the moons of Mars, are interesting exploration destinations that offer extensibility of the Asteroid Redirect Mission (ARM) technologies. Solar Electric Propulsion (SEP), asteroid rendezvous and docking, and surface operations can be used to land on and explore the moons of Mars. The close Mars vicinity of Phobos and Deimos warrant examining them as waypoints, or intermediate staging orbits, for Mars surface missions. This paper outlines the analysis performed to determine the mass impact of using the moons of Mars both as an intermediate staging point for exploration as well as for in-situ recourse utilization, namely propellant, to determine if the moons are viable options to include in the broader Mars surface exploration architecture.

  4. [Analysis of statutory health insurance data concerning utilization of support surfaces for pressure ulcers].

    Science.gov (United States)

    Hoffmann, Falk; Scharnetzky, Elke; Deitermann, Bernhilde; Glaeske, Gerd

    2006-10-01

    Support surfaces are commonly used to prevent and treat pressure ulcers. Up to now little is known about their application in Germany. We conducted a cross-sectional study using claims data of the Gmuender ErsatzKasse (GEK) for the year 2004 to analyse the utilization of support surfaces for pressure ulcers in primary care. Based on age- and sex-specific treatment prevalences for individuals with at least one prescription, prevalence ratios (PR) were calculated. A total of 1999 subjects with a mean age of 63.4 years (SD: 20.7) received support surfaces for pressure ulcers. With respect to the numbers of prescriptions (n = 2421) alternating pressure mattresses (31.6%), air-filled rings (13.5%) and various seat cushions (13.0%) were used frequently, whereas foam mattresses only came to 4.7%. The treatment prevalence increases continuously with age with no sex-specific differences. Using the 50-59 year olds as a reference, men aged 90+ (PR: 43.94; 95% CI: 31.46-61.37) as well as women aged 90+ (PR: 40.61; 95% CI: 30.77-53.60) received approximately 40-times more often support surfaces for pressure ulcers. Support surfaces for pressure ulcers are commonly used in the elderly. Our study suggests that their application does not correspond to the best available evidence. Prevention and treatment of pressure ulcers as well as the selection of support surfaces should be seen as an interdisciplinary task.

  5. Characterization plan for the waste holding basin (3513 impoundment)

    International Nuclear Information System (INIS)

    Stansfield, R.G.; Francis, C.W.

    1986-09-01

    US Department of Energy (DOE) facilities are required to comply fully with all federal and state regulations. In response to this requirement, the Oak Ridge National Laboratory (ORNL) has established the remedial action program, to provide comprehensive management of areas where past research, development, and waste management activities have been conducted and have resulted in residual contamination of facilities or the environment. One of the objectives of this program is to define the extent of contamination at these sites. The intent is to document the known environmental characteristics of the sites and identify the additional actions, such as sampling, analytical measurements, and modeling, necessary to confirm contamination and the possible migration of contaminants from the sites. One of these sites is the waste holding basin (3513 impoundment). The 3513 impoundment is an unlined waste settling basin constructed in 1944 for collection of ORNL wastewater before its discharge into White Oak Creek. Operation of the facility ceased in 1976 when a new process waste treatment plant came into operation. Considerable site-specific environmental information has been developed over the years relative to the type and quantities of radionuclides and hazardous substances contained in the pond water and sediment. The concentrations and patterns of distribution for many of the radionuclides in the aquatic biota as well as for the terrestrial plants growing on the berm of the impoundment have been determined by DOE ecological studies. Recently, some data were collected that evaluate the extent of contaminant movement to the groundwater. Results from these studies are summarized in this report. Also included in this report is an outline of additional tasks needed to obtain the necessary information to model the transport and dose pathways of hazardous substances from the site

  6. Characterization plan for the waste holding basin (3513 impoundment)

    Energy Technology Data Exchange (ETDEWEB)

    Stansfield, R.G.; Francis, C.W.

    1986-09-01

    US Department of Energy (DOE) facilities are required to comply fully with all federal and state regulations. In response to this requirement, the Oak Ridge National Laboratory (ORNL) has established the remedial action program, to provide comprehensive management of areas where past research, development, and waste management activities have been conducted and have resulted in residual contamination of facilities or the environment. One of the objectives of this program is to define the extent of contamination at these sites. The intent is to document the known environmental characteristics of the sites and identify the additional actions, such as sampling, analytical measurements, and modeling, necessary to confirm contamination and the possible migration of contaminants from the sites. One of these sites is the waste holding basin (3513 impoundment). The 3513 impoundment is an unlined waste settling basin constructed in 1944 for collection of ORNL wastewater before its discharge into White Oak Creek. Operation of the facility ceased in 1976 when a new process waste treatment plant came into operation. Considerable site-specific environmental information has been developed over the years relative to the type and quantities of radionuclides and hazardous substances contained in the pond water and sediment. The concentrations and patterns of distribution for many of the radionuclides in the aquatic biota as well as for the terrestrial plants growing on the berm of the impoundment have been determined by DOE ecological studies. Recently, some data were collected that evaluate the extent of contaminant movement to the groundwater. Results from these studies are summarized in this report. Also included in this report is an outline of additional tasks needed to obtain the necessary information to model the transport and dose pathways of hazardous substances from the site.

  7. Run-of-River Impoundments Can Remain Unfilled While Transporting Gravel Bedload: Numerical Modeling Results

    Science.gov (United States)

    Pearson, A.; Pizzuto, J. E.

    2015-12-01

    Previous work at run-of-river (ROR) dams in northern Delaware has shown that bedload supplied to ROR impoundments can be transported over the dam when impoundments remain unfilled. Transport is facilitated by high levels of sand in the impoundment that lowers the critical shear stresses for particle entrainment, and an inversely sloping sediment ramp connecting the impoundment bed (where the water depth is typically equal to the dam height) with the top of the dam (Pearson and Pizzuto, in press). We demonstrate with one-dimensional bed material transport modeling that bed material can move through impoundments and that equilibrium transport (i.e., a balance between supply to and export from the impoundment, with a constant bed elevation) is possible even when the bed elevation is below the top of the dam. Based on our field work and previous HEC-RAS modeling, we assess bed material transport capacity at the base of the sediment ramp (and ignore detailed processes carrying sediment up and ramp and over the dam). The hydraulics at the base of the ramp are computed using a weir equation, providing estimates of water depth, velocity, and friction, based on the discharge and sediment grain size distribution of the impoundment. Bedload transport rates are computed using the Wilcock-Crowe equation, and changes in the impoundment's bed elevation are determined by sediment continuity. Our results indicate that impoundments pass the gravel supplied from upstream with deep pools when gravel supply rate is low, gravel grain sizes are relatively small, sand supply is high, and discharge is high. Conversely, impoundments will tend to fill their pools when gravel supply rate is high, gravel grain sizes are relatively large, sand supply is low, and discharge is low. The rate of bedload supplied to an impoundment is the primary control on how fast equilibrium transport is reached, with discharge having almost no influence on the timing of equilibrium.

  8. Groundwater monitoring at three Oak Ridge National Laboratory inactive waste impoundments: results after one year

    Energy Technology Data Exchange (ETDEWEB)

    Francis, C. W.; Stansfield, R. G.

    1986-10-01

    To determine if the migration of potential contaminants from three inactive waste impoundments at Oak Ridge National Laboratory poses a threat to groundwater quality, at least one upgradient groundwater monitoring well and threee downgradient monitoring wells were installed at each impoundment in early 1985. These three unlined impoundments, formerly used to collect and, in some instances, treat wastewater are: the 3513 impoundment; the Old Hydrofracture Facility (OHF) impoundment; and the Homogeneous Reactor Experimnt No. 2 impoundment. Groundwater samples were collected quarterly for one year. Analyses were conducted for the groundwater protection parameters promulgated by the Resource Conservation and Recovery Act. The groundwater samples were also analyzed for polychlorinated biphenyls, copper, nickel, zinc, /sup 90/Sr, /sup 137/Cs, and tritium. The contaminants found most often to affect groundwater quality at all three waste impoundments were radionuclides. For example, mean concentrations of gross beta and gross alpha activity exceeded drinking water limits at all three sites. The gross beta limit was exceeded at the 3513 and OHF impoundments by either /sup 90/Sr or tritium levels. At the 3513 impoundment, there was substantial evidence that the downgradient groundwater has been contaminated by chromium and lead and possibly by halogenated organic compounds. At the OHF impoundment, the mean level of tritium measured in the upgradient well (about 91,000 Bq/L as compared with 80,000 Bq/L in the downgradient wells) indicated that the groundwater quality has been affected by the radioactive wastes buried in the low-level radioactive waste burial ground solid waste storage area-5 upgradient of the impoundment. Testing for groundwater contamination, disclosed statistically significant contamination at all three sites.

  9. Groundwater monitoring at three Oak Ridge National Laboratory inactive waste impoundments: results after one year

    International Nuclear Information System (INIS)

    Francis, C.W.; Stansfield, R.G.

    1986-10-01

    To determine if the migration of potential contaminants from three inactive waste impoundments at Oak Ridge National Laboratory poses a threat to groundwater quality, at least one upgradient groundwater monitoring well and threee downgradient monitoring wells were installed at each impoundment in early 1985. These three unlined impoundments, formerly used to collect and, in some instances, treat wastewater are: the 3513 impoundment; the Old Hydrofracture Facility (OHF) impoundment; and the Homogeneous Reactor Experimnt No. 2 impoundment. Groundwater samples were collected quarterly for one year. Analyses were conducted for the groundwater protection parameters promulgated by the Resource Conservation and Recovery Act. The groundwater samples were also analyzed for polychlorinated biphenyls, copper, nickel, zinc, 90 Sr, 137 Cs, and tritium. The contaminants found most often to affect groundwater quality at all three waste impoundments were radionuclides. For example, mean concentrations of gross beta and gross alpha activity exceeded drinking water limits at all three sites. The gross beta limit was exceeded at the 3513 and OHF impoundments by either 90 Sr or tritium levels. At the 3513 impoundment, there was substantial evidence that the downgradient groundwater has been contaminated by chromium and lead and possibly by halogenated organic compounds. At the OHF impoundment, the mean level of tritium measured in the upgradient well (about 91,000 Bq/L as compared with 80,000 Bq/L in the downgradient wells) indicated that the groundwater quality has been affected by the radioactive wastes buried in the low-level radioactive waste burial ground solid waste storage area-5 upgradient of the impoundment. Testing for groundwater contamination, disclosed statistically significant contamination at all three sites

  10. PPE Surface Proteins Are Required for Heme Utilization by Mycobacterium tuberculosis

    Directory of Open Access Journals (Sweden)

    Avishek Mitra

    2017-01-01

    Full Text Available Iron is essential for replication of Mycobacterium tuberculosis, but iron is efficiently sequestered in the human host during infection. Heme constitutes the largest iron reservoir in the human body and is utilized by many bacterial pathogens as an iron source. While heme acquisition is well studied in other bacterial pathogens, little is known in M. tuberculosis. To identify proteins involved in heme utilization by M. tuberculosis, a transposon mutant library was screened for resistance to the toxic heme analog gallium(III-porphyrin (Ga-PIX. Inactivation of the ppe36, ppe62, and rv0265c genes resulted in resistance to Ga-PIX. Growth experiments using isogenic M. tuberculosis deletion mutants showed that PPE36 is essential for heme utilization by M. tuberculosis, while the functions of PPE62 and Rv0265c are partially redundant. None of the genes restored growth of the heterologous M. tuberculosis mutants, indicating that the proteins encoded by the genes have separate functions. PPE36, PPE62, and Rv0265c bind heme as shown by surface plasmon resonance spectroscopy and are associated with membranes. Both PPE36 and PPE62 proteins are cell surface accessible, while the Rv0265c protein is probably located in the periplasm. PPE36 and PPE62 are, to our knowledge, the first proline-proline-glutamate (PPE proteins of M. tuberculosis that bind small molecules and are involved in nutrient acquisition. The absence of a virulence defect of the ppe36 deletion mutant indicates that the different iron acquisition pathways of M. tuberculosis may substitute for each other during growth and persistence in mice. The emerging model of heme utilization by M. tuberculosis as derived from this study is substantially different from those of other bacteria.

  11. Reestablishing the Dominance of Biogeochemical Pathways for Reducing Downstream Nutrient Losses from Aged Impounded Features

    Science.gov (United States)

    Shukla, S.; Shukla, A.

    2017-12-01

    Water and phosphorus (P) dynamics and loss pathways at two stormwater impoundments (SIs) were analyzed using measured fluxes between 2008 and 2011. These SIs are a decade old. Analyses of water and P budgets along with the discernment of various P pools and characterization of the intermediary processes revealed that soil adsorption and plant uptake are secondary to volume reduction apropos of P treatment. At one site, extreme wet conditions in a year combined with soil P saturation resulted in it being a P source rather than a sink. The impoundment (SI-1) discharged 12% more P than incoming due to soil P desorption, a consequence of dilution of incoming stormwater with large water input from an extreme tropical rain event. The second impoundment (SI-2) was a consistent sink of P; 55% and 95% of the incoming total P was retained in the two years, mainly as a result of 49% and 84% volume retention, respectively. Analysis of plant available aluminum, iron, and phosphorus showed the surface soil to be P saturated and at risk of releasing P to a limit of environmental concern. These results when seen in light of more frequent extreme precipitation events under the changed climate scenario call for alternatives to revive the role of biogeochemical processes in P treatment because volume reduction may not always be the viable option, especially for wet conditions. Aboveground biomass harvesting and removal was evaluated to transform the SIs from a frequent P source to sink and maintain the long-term sink functions of the SIs. Use of harvested biomass as a source of nutrients (N and P) and carbon to agricultural soil can result in beneficial use of biomass and offset the cost of harvesting. Other avenues such as altering the hydrology of the SIs by compartmentalizing the system and increasing the storage were also explored for short-term benefits. Results provided a combination of hydraulic and biochemical options for achieving long-term water and nutrient retentions in

  12. 32 CFR 634.52 - Search incident to impoundment based on criminal activity.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Search incident to impoundment based on criminal activity. 634.52 Section 634.52 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) LAW ENFORCEMENT AND CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION Impounding...

  13. Out of Thin Air: Microbial Utilization of Atmospheric Gaseous Organics in the Surface Ocean

    KAUST Repository

    Arrieta, Jesus

    2016-01-20

    Volatile and semi-volatile gas-phase organic carbon (GOC) is a largely neglected component of the global carbon cycle, with poorly resolved pools and fluxes of natural and anthropogenic GOC in the biosphere. Substantial amounts of atmospheric GOC are exchanged with the surface ocean, and subsequent utilization of specific GOC compounds by surface ocean microbial communities has been demonstrated. Yet, the final fate of the bulk of the atmospheric GOC entering the surface ocean is unknown. Our data show experimental evidence of efficient use of atmospheric GOC by marine prokaryotes at different locations in the NE Subtropical Atlantic, the Arctic Ocean and the Mediterranean Sea. We estimate that between 2 and 27% of the prokaryotic carbon demand was supported by GOC with a major fraction of GOC inputs being consumed within the mixed layer. The role of the atmosphere as a key vector of organic carbon subsidizing marine microbial metabolism is a novel link yet to be incorporated into the microbial ecology of the surface ocean as well as into the global carbon budget.

  14. The Utility of Using a Near-Infrared (NIR) Camera to Measure Beach Surface Moisture

    Science.gov (United States)

    Nelson, S.; Schmutz, P. P.

    2017-12-01

    Surface moisture content is an important factor that must be considered when studying aeolian sediment transport in a beach environment. A few different instruments and procedures are available for measuring surface moisture content (i.e. moisture probes, LiDAR, and gravimetric moisture data from surface scrapings); however, these methods can be inaccurate, costly, and inapplicable, particularly in the field. Near-infrared (NIR) spectral band imagery is another technique used to obtain moisture data. NIR imagery has been predominately used through remote sensing and has yet to be used for ground-based measurements. Dry sand reflects infrared radiation given off by the sun and wet sand absorbs IR radiation. All things considered, this study assesses the utility of measuring surface moisture content of beach sand with a modified NIR camera. A traditional point and shoot digital camera was internally modified with the placement of a visible light-blocking filter. Images were taken of three different types of beach sand at controlled moisture content values, with sunlight as the source of infrared radiation. A technique was established through trial and error by comparing resultant histogram values using Adobe Photoshop with the various moisture conditions. The resultant IR absorption histogram values were calibrated to actual gravimetric moisture content from surface scrapings of the samples. Overall, the results illustrate that the NIR spectrum modified camera does not provide the ability to adequately measure beach surface moisture content. However, there were noted differences in IR absorption histogram values among the different sediment types. Sediment with darker quartz mineralogy provided larger variations in histogram values, but the technique is not sensitive enough to accurately represent low moisture percentages, which are of most importance when studying aeolian sediment transport.

  15. Utility of Gram stain for the microbiological analysis of burn wound surfaces.

    Science.gov (United States)

    Elsayed, Sameer; Gregson, Daniel B; Lloyd, Tracie; Crichton, Marilyn; Church, Deirdre L

    2003-11-01

    Surface swab cultures have attracted attention as a potential alternative to biopsy histology or quantitative culture methods for microbiological burn wound monitoring. To our knowledge, the utility of adding a Gram-stained slide in this context has not been evaluated previously. To determine the degree of correlation of Gram stain with culture for the microbiological analysis of burn wound surfaces. Prospective laboratory analysis. Urban health region/centralized diagnostic microbiology laboratory. Burn patients hospitalized in any Calgary Health Region burn center from November 2000 to September 2001. Gram stain plus culture of burn wound surface swab specimens obtained during routine dressing changes or based on clinical signs of infection. Degree of correlation (complete, high, partial, none), including weighted kappa statistic (kappa(w)), of Gram stain with culture based on quantitative microscopy and degree of culture growth. A total of 375 specimens from 50 burn patients were evaluated. Of these, 239 were negative by culture and Gram stain, 7 were positive by Gram stain only, 89 were positive by culture only, and 40 were positive by both methods. The degree of complete, high, partial, and no correlation of Gram stain with culture was 70.9% (266/375), 1.1% (4/375), 2.4% (9/375), and 25.6% (96/375), respectively. The degree of correlation for all 375 specimens, as expressed by the weighted kappa statistic, was found to be fair (kappa(w) = 0.32).Conclusion.-The Gram stain is not suitable for the microbiological analysis of burn wound surfaces.

  16. Self-formation and release of arbitrary-curvatured structures utilizing droplet deposition and structured surface

    International Nuclear Information System (INIS)

    Chen, Chin-Tai; Chieng, Ching-Chang; Tseng, Fan-Gang

    2008-01-01

    This paper proposes a method of micro-fabrication for the formation of complex non-planar shapes by depositing a colloid evaporative droplet onto topographically structured surfaces. The micro-droplet composed of polyurethane (PU) was self-driven by surface tension to adjust their three-dimensional (3D) shapes bound with the surface of the micro-well array. The micro-wells formed from poly-dimethysiloxane (PDMS) consisted of vertical sidewalls to constrain the fluids as boundary conditions in the Young–Laplace equation until drying. Two types of wetting regimes (fully and partially), corresponding to different droplet volume and allocation, were categorized to perform the shaping process in which evolving fluid contours were self-formed utilizing the general principle of minimal surface energy with certain features of the shape set by the wetting of the PDMS. Using the heterogeneous surfaces, slight-concave circular terraces and half-moon shapes with high curvature were fabricated with micrometer dimensions (well diameter of 900 µm). The formed structures were observed to release themselves from the hydrophobic wells by the de-wetting (de-pinned) process in the completion of evaporation. Moreover, the effects of the boundaries were further explored for half-moon shapes by giving three distinct footprints of the partially wetting droplets. In these cases, both experimental results and numerical calculations were performed and compared to illustrate the significant influence of the fluid contact angle (∼90°) and position with a curved boundary line on final formed shape, in particular for the change of curvature (κ-bar = 0.62–1.36). Compared to those traditional assays operated on two-dimensional (2D) flat surfaces, this structured-well one could greatly enhance the control of 3D topographic formation in terms of aspect ratio, thickness and curved degree. This novel operation of micro-fabrication is also appropriate for smaller and complex structures by

  17. Eutrophication levels of some South African impoundments. IV. Vaal Dam

    CSIR Research Space (South Africa)

    Steyn, DJ

    1976-04-01

    Full Text Available I?d/st. Loners I, 74, I ?34-I 42. TOERIEN, D. F., STEtN, D.J. and KOHLMEYER, 5.1. (1975a).The nitrogen yield coellieien t of the g ?ccii alga .Seleooastrsmn rapr,corn,tesm Printz. S. Afe. J. Sri., 7!, 217-218. TOERtEN, D.F.,HVMAN,KATHYL.5nd... inere;iae(l the \\G P In? between 7,1- and I 1,2 mg/r? lbr t?verv nile pet? t?t?ttt v/v) added_Nitrogen and phosphorus wert? the important algal growth?limiting ntltrients in the impoundment. Plant nntt-ients adsorbed onto clay particles could ht...

  18. A generic model of contaminant migration from uranium tailings impoundments

    International Nuclear Information System (INIS)

    Shepherd, T.A.; Brown, S.E.

    1982-01-01

    This paper presents an analytical hydrogeochemical model based upon acid consumption-neutralization front movement. The development of contaminant plumes is discussed and distinct zones within these plumes are identified and characterized. The most important process influencing the rate and extent of contaminant migration at acid-leach uranium tailings impoundments is the neutralization of seepage water by soils along ground water flow paths. The chemical characteristics of the ground water is determined in order to identify and characterize zones within migrating plumes of tailings-derived water. It is concluded that the characterization of specific zones is useful in the interpretation of existing conditions, in the evaluation of future migration, and in the determination of appropriate models for the specific situation

  19. Quantitative and Qualitative Analysis of Surface Modified Cellulose Utilizing TGA-MS

    Directory of Open Access Journals (Sweden)

    Daniel Loof

    2016-05-01

    Full Text Available With the aim to enhance interfacial adhesion of a hydrophobic polymer matrix and cellulosic fibers and fillers, chemical surface modifications with silane coupling agents are performed. Thermogravimetric analysis (TGA could be used to determine the degree of surface functionalization. However, similar thermal properties of treated and untreated cellulose hamper a precise determination of silane loading. This contribution deals with quantitative determination of silane loading combining both TGA and elemental analysis. Firstly, silane modified celluloses were studied by FT-IR, Raman, solid state NMR spectroscopy, and polarized light microscopy in order to determine functional groups and to study the impact of chemical treatment on cellulose morphology. Secondly, thermal stability and pyrolysis processes were studied by TG-MS analysis. In order to determine the exact silane loading, the mass percentages of the appropriate elements were quantified by elemental analysis and correlated with the charred residues determined by TGA yielding a linear dependency. With that correlation, it was possible to determine silane loadings for additional samples utilizing simple TGA measurements. The main advantage of that approach is that only one calibration is necessary for routine analyses of further samples and TGA-MS coupling gives additional information on thermal stability and pyrolysis routes, simultaneously.

  20. Pressurization Risk Assessment of CO2 Reservoirs Utilizing Design of Experiments and Response Surface Methods

    Science.gov (United States)

    Guyant, E.; Han, W. S.; Kim, K. Y.; Park, E.; Han, K.

    2015-12-01

    Monitoring of pressure buildup can provide explicit information on reservoir integrity and is an appealing tool, however pressure variation is dependent on a variety of factors causing high uncertainty in pressure predictions. This work evaluated pressurization of a reservoir system in the presence of leakage pathways as well as exploring the effects of compartmentalization of the reservoir utilizing design of experiments (Definitive Screening, Box Behnken, Central Composite, and Latin Hypercube designs) and response surface methods. Two models were developed, 1) an idealized injection scenario in order to evaluate the performance of multiple designs, and 2) a complex injection scenario implementing the best performing design to investigate pressurization of the reservoir system. A holistic evaluation of scenario 1, determined that the Central Composite design would be used for the complex injection scenario. The complex scenario evaluated 5 risk factors: reservoir, seal, leakage pathway and fault permeabilities, and horizontal position of the pathway. A total of 60 response surface models (RSM) were developed for the complex scenario with an average R2 of 0.95 and a NRMSE of 0.067. Sensitivity to the input factors was dynamic through space and time; at the earliest time (0.05 years) the reservoir permeability was dominant, and for later times (>0.5 years) the fault permeability became dominant for all locations. The RSM's were then used to conduct a Monte Carlo Analysis to further analyze pressurization risks, identifying the P10, P50, P90 values. This identified the in zone (lower) P90 values as 2.16, 1.77, and 1.53 MPa and above zone values of 1.35, 1.23, 1.09 MPa for monitoring locations 1, 2, and 3, respectively. In summary, the design of experiments and response surface methods allowed for an efficient sensitivity and uncertainty analysis to be conducted permitting a complete evaluation of the pressurization across the entire parameter space.

  1. Formation of biodegradable microcapsules utilizing 3D, selectively surface-modified PDMS microfluidic devices.

    Science.gov (United States)

    Liao, Chung-Yu; Su, Yu-Chuan

    2010-02-01

    We have successfully demonstrated the formation of biodegradable microcapsules utilizing PDMS double-emulsification devices. Specially designed 3D PDMS microchannels with surfaces selectively modified by a self-aligned photografting process are employed to generate monodisperse water-in-organic-solvent-in-water (W/O/W) emulsions in a controlled manner. Mainly by varying the outer and inner fluid flow-rates, the dimensions of resulting double emulsions can be adjusted as desired. Meanwhile, biodegradable materials are dissolved in the middle organic solvent (in this work ethyl acetate is used), and solidified into microcapsules once the solvent is extracted. In the prototype demonstration, microcapsules made up of poly(L-lactic acid), trilaurin, and phosphocholine were successfully fabricated. In addition, it was also demonstrated that gamma-Fe(2)O(3) nanoparticles can be simultaneously embedded into the microcapsules, which consequently become responsive to electromagnetic stimulation. As such, the presented PDMS microfluidic devices could potentially serve as versatile encapsulation apparatus, and the fabricated biodegradable microcapsules could function as controlled delivery systems, which are desired for a variety of biological and pharmaceutical applications.

  2. On the utility of land surface models for agricultural drought monitoring

    Directory of Open Access Journals (Sweden)

    W. T. Crow

    2012-09-01

    Full Text Available The lagged rank cross-correlation between model-derived root-zone soil moisture estimates and remotely sensed vegetation indices (VI is examined between January 2000 and December 2010 to quantify the skill of various soil moisture models for agricultural drought monitoring. Examined modeling strategies range from a simple antecedent precipitation index to the application of modern land surface models (LSMs based on complex water and energy balance formulations. A quasi-global evaluation of lagged VI/soil moisture cross-correlation suggests, when globally averaged across the entire annual cycle, soil moisture estimates obtained from complex LSMs provide little added skill (< 5% in relative terms in anticipating variations in vegetation condition relative to a simplified water accounting procedure based solely on observed precipitation. However, larger amounts of added skill (5–15% in relative terms can be identified when focusing exclusively on the extra-tropical growing season and/or utilizing soil moisture values acquired by averaging across a multi-model ensemble.

  3. Efficient harvesting of marine Chlorella vulgaris microalgae utilizing cationic starch nanoparticles by response surface methodology.

    Science.gov (United States)

    Bayat Tork, Mahya; Khalilzadeh, Rasoul; Kouchakzadeh, Hasan

    2017-11-01

    Harvesting involves nearly thirty percent of total production cost of microalgae that needs to be done efficiently. Utilizing inexpensive and highly available biopolymer-based flocculants can be a solution for reducing the harvest costs. Herein, flocculation process of Chlorella vulgaris microalgae using cationic starch nanoparticles (CSNPs) was evaluated and optimized through the response surface methodology (RSM). pH, microalgae and CSNPs concentrations were considered as the main independent variables. Under the optimum conditions of microalgae concentration 0.75gdry weight/L, CSNPs concentration 7.1mgdry weight/L and pH 11.8, the maximum flocculation efficiency (90%) achieved. Twenty percent increase in flocculation efficiency observed with the use of CSNPs instead of the non-particulate starch which can be due to the more electrostatic interactions between the cationic nanoparticles and the microalgae. Therefore, the synthesized CSNPs can be employed as a convenient and economical flocculants for efficient harvest of Chlorella vulgaris microalgae at large scale. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Efficiency of baited hoop nets for sampling catfish in southeastern U.S. small impoundments

    Science.gov (United States)

    Wallace, Benjamin C.; Weaver, Daniel M.; Kwak, Thomas J.

    2011-01-01

    Many U.S. natural resource agencies stock catfish (Ictaluridae) into small impoundments to provide recreational fishing opportunities. However, effective standardized methods for sampling catfish in small impoundments have not been developed for wide application, particularly in the southeastern United States. We evaluated the efficiency of three bait treatments (i.e., soybean cake, sunflower cake, and no bait) of tandem hoop nets in two North Carolina small impoundments during the fall of 2008 and spring of 2009 in a factorial experimental design. The impoundments were stocked with catchable-size channel catfish Ictalurus punctatus at contrastingly low (5.5 fi sh/ha) and high (90.0 fi sh/ha) rates prior to our sampling. Nets baited with soybean cake consistently sampled more channel catfish than any other treatment. Channel catfish catch ranged as high as 3,251 fi sh per net series during the fall in nets baited with soybean cake in the intensively stocked impoundment and was up to 8.5 and 15.3 times higher during the fall than in the spring in each impoundment. Nets baited with soybean cake sampled significantly (12 and 24 times) more channel catfish than those with no bait in the two impoundments. These trends did not occur among other catfish species. Nonictalurid fish and turtle catch was higher during spring compared to that of fall, corresponding with low channel catfish catches. Our results indicate that tandem hoop nets baited with soybean cake during the fall is a more efficient method for sampling channel catfish compared to nets baited with sunflower cake or no bait in spring or fall. Our findings validate this technique for application in southeastern U.S. small impoundments to assess catfish abundance to guide management and evaluate the success of catfish stocking programs.

  5. Relative amplitude preservation processing utilizing surface consistent amplitude correction. Part 4; Surface consistent amplitude correction wo mochiita sotai shinpuku hozon shori. 4

    Energy Technology Data Exchange (ETDEWEB)

    Saeki, T. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-10-22

    Discussions were given on seismic exploration from the ground surface using the reflection method, for surface consistent amplitude correction from among effects imposed from the ground surface and a surface layer. Amplitude distribution on the reflection wave zone is complex. Therefore, items to be considered in making an analysis are multiple, such as estimation of spherical surface divergence effect and exponential attenuation effect, not only amplitude change through the surface layer. If all of these items are taken into consideration, burden of the work becomes excessive. As a method to solve this problem, utilization of amplitude in initial movement of a diffraction wave may be conceived. Distribution of the amplitude in initial movement of the diffraction wave shows a value relatively close to distribution of the vibration transmitting and receiving points. The reason for this is thought because characteristics of the vibration transmitting and receiving points related with waveline paths in the vicinity of the ground surface have no great difference both on the diffraction waves and on the reflection waves. The lecture described in this paper introduces an attempt of improving the efficiency of the surface consistent amplitude correction by utilizing the analysis of amplitude in initial movement of the diffraction wave. 4 refs., 2 figs.

  6. Pournari Dam (W. Greece) Impoundment and Triggered Seismicity

    Science.gov (United States)

    Pavlou, K.; Kouskouna, V.; Makropoulos, K.; Drakatos, G.; Petrou, P.

    2012-04-01

    The Pournari dam is located in the seismically active area of W. Greece, close to Arta. The height of the dam is 87m, with maximum water level height at 126m and maximum volume 865X106m3. The first impoundment commenced in January 1981, and was accompanied by a considerable number of low magnitude seismic events, as well as two major ones on March 10 and April 10, 1981, with magnitudes ML=5.6 and ML=4.7 and focal depths 13km and 10km, respectively, all located in the broader area of the dam. Potential triggering of the second event was studied through the calculation of Coulomb stress changes distribution, due to the occurrence of the first ML=5.6 event. Additionally, the detailed study of temporal correlation between water level increase and seismicity showed triggering seismicity due to both the initial filling and the disordered structure, controlled by the presence of evaporites, south and west of Pournari dam area. Further processing of the recorded seismicity for the period 1982-2010, in comparison with the variations of Pournari dam water level, presented an increase of shallow seismicity in the vicinity of the reservoir up to a 10 km distance -in contrast to the initial period, characterized by a number of deeper events- which was due to the background response change from undrained to drained status.

  7. Presentations from the 1992 Coal Mining Impoundment Informational Meeting

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-31

    On May 20 and 21, 1992, the MSHA Coal Mining Impoundment Informational Meeting was held at the National Mine Health and Safety Academy in Beckley, West Virginia. Fifteen presentations were given on key issues involved in the design and construction of dams associated with coal mining. The attendees were told that to improve the consistency among the plan reviewers, engineers from the Denver and Pittsburgh Technical Support Centers meet twice annually to discuss specific technical issues. It was soon discovered that the topics being discussed needed to be shared with anyone involved with coal waste dam design, construction, or inspection. The only way to accomplish that goal was through the issuance of Procedure Instruction Letters. The Letters present a consensus of engineering philosophy that could change over time. They do not present policy or carry the force of law. Currently, thirteen position papers have been disseminated and more will follow as the need arises. The individual paper were not even entered into the database.

  8. Using Helicopter Electromagnetic Surveys to Identify Potential Hazards at Mine Waste Impoundments

    Energy Technology Data Exchange (ETDEWEB)

    Hammack, R.W.

    2008-01-01

    In July 2003, helicopter electromagnetic surveys were conducted at 14 coal waste impoundments in southern West Virginia. The purpose of the surveys was to detect conditions that could lead to impoundment failure either by structural failure of the embankment or by the flooding of adjacent or underlying mine works. Specifically, the surveys attempted to: 1) identify saturated zones within the mine waste, 2) delineate filtrate flow paths through the embankment or into adjacent strata and receiving streams, and 3) identify flooded mine workings underlying or adjacent to the waste impoundment. Data from the helicopter surveys were processed to generate conductivity/depth images. Conductivity/depth images were then spatially linked to georeferenced air photos or topographic maps for interpretation. Conductivity/depth images were found to provide a snapshot of the hydrologic conditions that exist within the impoundment. This information can be used to predict potential areas of failure within the embankment because of its ability to image the phreatic zone. Also, the electromagnetic survey can identify areas of unconsolidated slurry in the decant basin and beneath the embankment. Although shallow, flooded mineworks beneath the impoundment were identified by this survey, it cannot be assumed that electromagnetic surveys can detect all underlying mines. A preliminary evaluation of the data implies that helicopter electromagnetic surveys can provide a better understanding of the phreatic zone than the piezometer arrays that are typically used.

  9. Tidal management sffects sub-adult fish assemblages in impounded South Carolina Marshes

    Science.gov (United States)

    Carswell, Ben L.; Peterson, James T.; Jennings, Cecil A.

    2015-01-01

    In coastal South Carolina, most impounded marshes are managed for waterfowl; fewer are managed for fishes. Tidal control is central to each strategy but raises concerns that nursery function could be impaired. This research examined the assemblage composition of fishes during early-life stages. We sampled two impoundments of each management type monthly in 2008 and 2009. We used light traps to collect 61,527 sub-adult fish representing 21 species and 16 families and push nets to collect 12,670 sub-adult fish representing 13 species and 11 families. The effective number of species detected at larval stage in “fish” impoundments (summer mean = 2.52 ± 0.20, winter mean = 2.02 ± 0.66) was greater than in “waterfowl” impoundments (summer mean = 1.27 ± 0.14, winter mean = 1.06 ± 0.09); CI = 90 %. Species richness did not differ between management types, but hierarchical linear models predicted differences in assemblage composition. These findings underscore the importance of frequent water exchange for maintaining diverse assemblages of early-life-stage fishes in marsh impoundments.

  10. A Summary of NASA Architecture Studies Utilizing Fission Surface Power Technology

    Science.gov (United States)

    Mason, Lee S.; Poston, David I.

    2011-01-01

    Beginning with the Exploration Systems Architecture Study in 2005, NASA has conducted various mission architecture studies to evaluate implementation options for the U.S. Space Policy. Several of the studies examined the use of Fission Surface Power (FSP) systems for human missions to the lunar and Martian surface. This paper summarizes the FSP concepts developed under four different NASA-sponsored architecture studies: Lunar Architecture Team, Mars Architecture Team, Lunar Surface Systems/Constellation Architecture Team, and International Architecture Working Group-Power Function Team.

  11. Effect of ship locking on sediment oxygen uptake in impounded rivers

    DEFF Research Database (Denmark)

    Lorke, A.; McGinnis, D. F.; Maeck, A.

    2012-01-01

    In the majority of large river systems, flow is regulated and/or otherwise affected by operational and management activities, such as ship locking. The effect of lock operation on sediment-water oxygen fluxes was studied within a 12.9 km long impoundment at the Saar River (Germany) using eddy......-correlation flux measurements. The continuous observations cover a time period of nearly 5 days and 39 individual locking events. Ship locking is associated with the generation of surges propagating back and forth through the impoundment which causes strong variations of near-bed current velocity and turbulence...

  12. Utilization of Sanitizing Wipes on Selected Coated Nonstick Food Contact Surfaces

    National Research Council Canada - National Science Library

    Powers, Edmund

    2002-01-01

    ... of field sanitation. The cleaning and bactericidal efficacy of commercial-off-the-shelf (COTS) sanitizing wipes was tested on specially coated non-stick food contact surfaces, also under investigation by the Army...

  13. Microbial communities in a porphyry copper tailings impoundment and their impact on the geochemical dynamics of the mine waste.

    Science.gov (United States)

    Diaby, Nouhou; Dold, Bernhard; Pfeifer, Hans-Rudolf; Holliger, Christof; Johnson, D Barrie; Hallberg, Kevin B

    2007-02-01

    The distribution and diversity of acidophilic bacteria of a tailings impoundment at the La Andina copper mine, Chile, was examined. The tailings have low sulfide (1.7% pyrite equivalent) and carbonate (1.4% calcite equivalent) contents and are stratified into three distinct zones: a surface (0-70-80 cm) 'oxidation zone' characterized by low-pH (2.5-4), a 'neutralization zone' (70-80 to 300-400 cm) and an unaltered 'primary zone' below 400 cm. A combined cultivation-dependent and biomolecular approach (terminal restriction enzyme fragment length polymorphism and 16S rRNA clone library analysis) was used to characterize the indigenous prokaryotic communities in the mine tailings. Total cell counts showed that the microbial biomass was greatest in the top 125 cm of the tailings. The largest numbers of bacteria (10(9) g(-1) dry weight of tailings) were found at the oxidation front (the junction between the oxidation and neutralization zones), where sulfide minerals and oxygen were both present. The dominant iron-/sulfur-oxidizing bacteria identified at the oxidation front included bacteria of the genus Leptospirillum (detected by molecular methods), and Gram-positive iron-oxidizing acidophiles related to Sulfobacillus (identified both by molecular and cultivation methods). Acidithiobacillus ferrooxidans was also detected, albeit in relatively small numbers. Heterotrophic acidophiles related to Acidobacterium capsulatum were found by molecular methods, while another Acidobacterium-like bacterium and an Acidiphilium sp. were isolated from oxidation zone samples. A conceptual model was developed, based on microbiological and geochemical data derived from the tailings, to account for the biogeochemical evolution of the Piuquenes tailings impoundment.

  14. Utilization of InSAR differential interferometry for surface deformation detection caused by mining

    Energy Technology Data Exchange (ETDEWEB)

    Yang, F. [Liaoning Technical Univ., Fuxin (China). School of Geomatics; Shao, Y. [Liaoning Technical Univ., Fuxin (China). Dept. of Foreign Language; Guichen, M. [Gifu Univ., Yanagido, Gifu (Japan). Dept. of Civil Engineering

    2010-07-01

    In China, the surface deformation of ground has been a significant geotechnical problem as a result of cracks in the ground surface, collapsing of house, and subsidence of roads. A powerful technology for detecting surface deformation in the ground is differential interferometry using synthetic aperture radar (INSAR). The technology enables the analysis from different phase of micro-wave between two observed data by synthetic aperture radar (SAR) of surface deformation of ground such as ground subsidence, land slide, and slope failure. In January 2006, the advanced land observing satellite was launched by the Japan Aerospace Exploration Agency. This paper presented an analytical investigation to detect ground subsidence or change caused by mining, overuse of ground water, and disaster. Specifically, the paper discussed the INSAR monitoring technology of the mine slope, including INSAR data sources and processing software; the principle of synthetic aperture radar interferometry; principles of differential SAR interferometry; and INSAR technology to slope monitoring of the Haizhou open pit mine. The paper also discussed the Haizhou strip mine side slope INSAR monitoring results and tests. It was concluded that the use of synthetic aperture radar interferometer technique was the optimal technique to provide three-dimensional spatial information and minimal change from ground surface by spatial remote sensing device. 18 refs., 5 figs.

  15. Limnology and fisheries of three recently impounded reservoirs in Sri Lanka

    International Nuclear Information System (INIS)

    Silva, K.H.G.M De

    1990-01-01

    The hydroelectric reservoirs of Kotmale, Victoria, and Randenigala were impounded in 1985, 1984, and 1986, respectively, by damming the Mahaweli River. The surface area, maximum depth, and mean depth of the three reservoirs are 6.3 km 2 , 78 m, 27.6 m; 23.7 km 2 , 102 m, 30.8 m; and 23.5 km 2 , 90 m, 36.6 m respectively, at their full supply levels of 703, 438, and 232 m above mean sea level. Important physicochemical factors and phytoplankton were studied by sampling of subsurface waters every two weeks in 12 randomly chosen stations in Randenigala and Victoria, and in 10 stations in Kotmale over 24 months. Mean water temperature, pH, conductivity, and the total alkalinity during the study period were 25.6 degree C, 6.6, 50.7 μsieverts, and 0.31 millimoles/l in Kotmale, 26.9 degree C, 7.1, 77.4 μsieverts, and 0.62 millimoles/l in Victoria, and 28.3 degree C, 7.4, 90.0 μsieverts, and 0.79 millimoles/l in Randenigala. The gill-net catches of Kotmale and Victoria are ca 38 and 70 kg/hectare/y, respectively. Randenigala has a fishery potential of ca 70 kg/hectare/y. Tilapia formed ca 68%, 59%, and 69% of the catches of Kotmale, Victoria, and Randenigala, respectively. The catch at Kotmale was mainly Java tilapia and Nile tilapia, whereas at the other two reservoirs it was mainly Java tilapia. Indigenous species constituted only ca 10% of the catch. 16 refs., 2 figs., 4 tabs

  16. DEVELOPMENT AND UTILIZATION OF TEST FACILITY FOR THE STUDY OF CANDLE FILTER SURFACE REGENERATION

    Energy Technology Data Exchange (ETDEWEB)

    Bruce S. Kang; Eric K. Johnson

    2003-07-14

    Hot gas particulate filtration is a basic component in advanced power generation systems such as Integrated Gasification Combined Cycle (IGCC) and Pressurized Fluidized Bed Combustion (PFBC). These systems require effective particulate removal to protect the downstream gas turbine and also to meet environmental emission requirements. The ceramic barrier filter is one of the options for hot gas filtration. Hot gases flow through ceramic candle filters leaving ash deposited on the outer surface of the filter. A process known as surface regeneration removes the deposited ash periodically by using a high pressure pulse of gas to back flush the filter. After this cleaning process has been completed there may be some residual ash on the filter surface. This residual ash may grow and this may then lead to mechanical failure of the filter. A Room Temperature Test Facility (RTTF) and a High Temperature Test Facility (HTTF) were built to investigate the ash characteristics during surface regeneration at room and selected high temperatures. The RTTF system was used to gain experience with the selected instrumentation and develop an operating procedure to be used later at elevated temperatures. The HTTF system is capable of conducting surface regeneration tests of a single candle filter at temperatures up to 1500 F. In order to obtain sequential digital images of ash particle distribution during the surface regeneration process, a high resolution, high speed image acquisition system was integrated into the HTTF system. The regeneration pressure and the transient pressure difference between the inside of the candle filter and the chamber during regeneration were measured using a high speed PC data acquisition system. The control variables for the high temperature regeneration tests were (1) face velocity, (2) pressure of the back pulse, and (3) cyclic ash built-up time. Coal ash sample obtained from the Power System Development Facility (PSDF) at Wilsonville, AL was used at the

  17. Nanobubble assisted nanopatterning utilized for ex situ identification of surface nanobubbles

    Czech Academy of Sciences Publication Activity Database

    Tarábková, Hana; Janda, Pavel

    2013-01-01

    Roč. 25, č. 18 (2013), s. 184001 ISSN 0953-8984 R&D Projects: GA ČR(CZ) GAP208/12/2429 Institutional support: RVO:61388955 Keywords : water * latex particles * hydrophobic surfaces Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.223, year: 2013

  18. Theoretical analysis of a fiber optic surface plasmon resonance sensor utilizing a Bragg grating

    Czech Academy of Sciences Publication Activity Database

    Špačková, Barbora; Homola, Jiří

    2009-01-01

    Roč. 17, č. 25 (2009), s. 23254-23264 ISSN 1094-4087 Institutional research plan: CEZ:AV0Z20670512 Keywords : Surface plasmon resonance * Fiber optic * Bragg grating * Biosensor * Coupled mode theory Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 3.278, year: 2009

  19. Gain-Enhanced On-Chip Antenna Utilizing Artificial Magnetic Conductor Reflecting Surface at 94 GHz

    KAUST Repository

    Nafe, Mahmoud

    2015-08-04

    Nowadays, there is a growing demand for high frequency-bandwidth mm-wave (30-300 GHz) electronic wireless transceiver systems to support applications such as high data-rate wireless communication and high resolution imaging. Such mm-wave systems are becoming more feasible due to the extreme transistor downscaling in silicon-based integrated circuits, which enabled densely-integrated high-speed elec- tronics operating up to more than 100 GHz with low fabrication cost. To further enhance system integrability, it is required to implement all wireless system compo- nents on the chip. Presently, the last major barrier to true System-on-Chip (SoC) realization is the antenna implementation on the silicon chip. Although at mm-wave frequencies the antenna size becomes small enough to fit on chip, the antenna performance is greatly deteriorated due the high conductivity and high relative permittivity of the silicon substrate. The negative e↵ects of the silicon substrate could be avoided by using a metallic reflecting surface on top of silicon, which e↵ectively isolates the antenna from the silicon. However, this approach has the shortcoming of having to implement the antenna on the usually very thin silicon oxide layer of a typical CMOS fabrication process (10’s of μm). This forces the antenna to be in a very close proximity (less than one hundredth of a wavelength) to the reflecting surface. In this regime, the use of conventional metallic reflecting surface for silicon shielding has severe e↵ects on the antenna performance as it tends to reduce the antenna radiation resistance resulting in most of the energy being absorbed rather than radiated. In this work, the use of specially patterned reflecting surfaces for improving on- chip antenna performance is investigated. By using a periodic metallic surface on top of a grounded substrate, the structure can mimic the behavior of a perfect mag- netic conductor, hence called Artificial Magnetic Conductor (AMC) surface

  20. Analysis of spatial distribution and inventory of radioactivity within the uranium mill tailings impoundment

    OpenAIRE

    D. O. Bugai; G. V. Laptev; O. S. Skalskyy; T. V. Lavrova; R. Avila

    2015-01-01

    Results are presented of the characterization of radioactivity inventory of Zapadnoe uranium mill tailings impoundment situated at Pridneprovsky Chemical Plant (PChP; Dneprodzerzhinsk, Ukraine). Analyses of radioactivity data set based on analytical studies of core material from 15 characterization boreholes allowed significantly refining waste volume and radioactivity inventory estimates. Geostatistical analyses using variogram function have established that radioactivity distribution in Zap...

  1. Partitions, Compartments and Portals: Cave Development in internally impounded karst masses.

    Directory of Open Access Journals (Sweden)

    Osborne R. Armstrong L.

    2005-07-01

    Full Text Available Dykes and other vertical bodies can act as aquicludes within bodies of karst rock. These partitions separate isolated bodies of solublerock called compartments. Speleogenetically each compartment will behave as a small impounded-karst until the partition becomesbreached. Breaches through partitions, portals, allow water, air and biota including humans to pass between sections of caves thatwere originally isolated.

  2. Effects of increased summer flooding on nitrogen dynamics in impounded mangroves

    NARCIS (Netherlands)

    Verhoeven, Jos T A; Laanbroek, Hendrikus J; Rains, Mark C; Whigham, Dennis F

    2014-01-01

    Mangroves are important for coastal protection, carbon sequestration and habitat provision for plants and animals in the tropics and subtropics. Mangroves are threatened by habitat destruction and sea level rise, but management activities such as impounding for mosquito control can also have

  3. LASER INDUCED SELECTIVE ACTIVATION UTILIZING AUTO-CATALYTIC ELECTROLESS PLATING ON POLYMER SURFACE

    DEFF Research Database (Denmark)

    Zhang, Yang; Nielsen, Jakob Skov; Tang, Peter Torben

    2009-01-01

    . Characterization of the deposited copper layer was used to select and improve laser parameters. Several types of polymers with different melting points were used as substrate. Using the above mentioned laser treatment, standard grades of thermoplastic materials such as ABS, SAN, PE, PC and others have been......This paper presents a new method for selective micro metallization of polymers induced by laser. An Nd: YAG laser was employed to draw patterns on polymer surfaces using a special set-up. After subsequent activation and auto-catalytic electroless plating, copper only deposited on the laser tracks....... Induced by the laser, porous and rough structures are formed on the surface, which favours the palladium attachment during the activation step prior to the metallization. Laser focus detection, scanning electron microscopy (SEM) and other instruments were used to analyze the topography of the laser track...

  4. Master Sintering Surface: A practical approach to its construction and utilization for Spark Plasma Sintering prediction

    Directory of Open Access Journals (Sweden)

    Pouchly V.

    2012-01-01

    Full Text Available The sintering is a complex thermally activated process, thus any prediction of sintering behaviour is very welcome not only for industrial purposes. Presented paper shows the possibility of densification prediction based on concept of Master Sintering Surface (MSS for pressure assisted Spark Plasma Sintering (SPS. User friendly software for evaluation of the MSS is presented. The concept was used for densification prediction of alumina ceramics sintered by SPS.

  5. Estimates of land surface heat fluxes of the Mt. Everest region over the Tibetan Plateau utilizing ASTER data

    Science.gov (United States)

    Han, Cunbo; Ma, Yaoming; Chen, Xuelong; Su, Zhongbo

    2016-02-01

    Regional land surface albedo, land surface temperature, net radiation flux, ground heat flux, sensible heat flux, and latent heat flux were derived in the Mt. Everest area utilizing topographical enhanced surface energy balance system (TESEBS) model and nine scenes of ASTER (Advanced Spaceborne Thermal Emission and Reflection Radiometer) data under clear-sky and in-situ measurements at the QOMS station (the Qomolangma Station for Atmospheric Environmental Observation and Research, Chinese Academy of Sciences). The parameterization schemes for diffused and reflected downward shortwave radiation flux of the TESEBS model were improved by introducing the parameters sky-view factor (SVF) and terrain configuration factor (Ct). Then, a so-called C-correction method for land surface albedo was coupled into the TESEBS model to reduce the influences of topography. After topographical correction, the albedo of the dark tilted surface facing away from the Sun was compensated and albedo of the brightness surface facing the Sun was restrained. The downward shortwave radiation flux was broken down into three components including solar direct radiation flux, solar diffused radiation flux, and reflected solar radiation flux by surrounding terrain. The solar diffused radiation flux ranges from about 30 to 60 W/m2 at the satellite passing time on 6 January 2008. The reflected solar radiation flux changes from 0 to more than 100 W/m2 in the area covered by glaciers and snows. Thus, it is important to take the topographical effects into account in estimation of surface radiation balance in the mountainous area, especially in the glacier area. The retrieved land surface parameters, land surface radiation balance components, and the land surface energy balance components were evaluated by the field measurements in the QOMS station. The estimated results were very close to the in-situ observations with low mean bias errors, low root mean square errors and high correlation coefficients

  6. Utilization of surface Plasmon resonance band of silver nanoparticles for determination of critical micelle concentration of cationic surfactants

    Science.gov (United States)

    Salem, Jamil K.; El-Nahhal, Issa M.; Najri, Bassam A.; Hammad, Talaat M.

    2016-11-01

    We have utilized surface Plasmon resonance (SPR) band sensitivity to surfactant concentration to investigate the critical micelle concentration (cmc) of CTAB, HY and CPB. The process is based upon an in situ formation of silver nanoparticles (AgNPs) through the reduction of silver ions (Ag+) by diethylene triamine (DETA) at 25 °C. In the presence of cationic surfactants, Ag+ ions can be reduced to AgNPs in a few minutes, accompanied by changes in intensity and wavelength of the SPR band. The spectral shifts of SPR band and the change of color have been used to determine CMC values of cationic surfactants.

  7. Environmental waste site characterization utilizing aerial photographs, remote sensing, and surface geophysics

    International Nuclear Information System (INIS)

    Pope, P.; Van Eeckhout, E.; Rofer, C.; Baldridge, S.; Ferguson, J.; Jiracek, G.; Balick, L.; Josten, N.; Carpenter, M.

    1996-01-01

    Six different techniques were used to delineate 40 year old trench boundary at Los Alamos National Laboratory. Data from historical aerial photographs, a magnetic gradient survey, airborne multispectral and thermal infra-red imagery, seismic refraction, DC resistivity, and total field magnetometry were utilized in this process. Each data set indicated a southern and northern edge for the trench. Average locations and 95% confidence limits for each edge were determined along a survey line perpendicular to the trench. Trench edge locations were fairly consistent among all six techniques. Results from a modeling effort performed with the total magnetic field data was the least consistent. However, each method provided unique and complementary information, and the integration of all this information led to a more complete characterization of the trench boundaries and contents

  8. Utilizing GNSS Reflectometry to Assess Surface Inundation Dynamics in Tropical Wetlands

    Science.gov (United States)

    Jensen, K.; McDonald, K. C.; Podest, E.; Chew, C. C.

    2017-12-01

    Tropical wetlands play a significant role in global atmospheric methane and terrestrial water storage. Despite the growing number of remote sensing products from satellite sensors, both spatial distribution and temporal variability of wetlands remain highly uncertain. An emerging innovative approach to mapping wetlands is offered by GNSS reflectometry (GNSS-R), a bistatic radar concept that takes advantage of GNSS transmitting satellites to yield observations with global coverage and rapid revisit time. This technology offers the potential to capture dynamic inundation changes in wetlands at higher temporal fidelity and sensitivity under the canopy than presently possible. We present an integrative analysis of radiometric modeling, ground measurements, and several microwave remote sensing datasets traditionally used for wetland observations. From a theoretical standpoint, GNSS-R sensitivities for vegetation and wetlands are investigated with a bistatic radar model in order to understand the interactions of the signal with various land surface components. GNSS reflections from the TechDemoSat-1 (TDS-1), Soil Moisture Active Passive (SMAP), and Cyclone GNSS (CYGNSS) missions are tested experimentally with contemporaneous (1) field measurements collected from the Pacaya Samiria National Reserve in the Peruvian Amazon, (2) imaging radar from Sentinel-1 and PALSAR-2 observed over a variety of tropical wetland systems, and (3) pan-tropical coarse-resolution (25km) microwave datasets (Surface Water Microwave Product Series). We find that GNSS-R data provide the potential to extend capabilities of current remote sensing techniques to characterize surface inundation extent, and we explore how to maximize synergism between different satellite sensors to produce an enhanced wetland monitoring product.

  9. Utilizing Higher Resolution Land Surface Remote Sensing Data for Assessing Recent Trends over Asia Monsoon Region

    Science.gov (United States)

    Shen, Suhung; Leptoukh, Gregory

    2010-01-01

    The slide presentation discusses the integration of 1-kilometer spatial resolution land temperature data from the Moderate Resolution Imaging Spectroradiometer (MODIS), with 8-day temporal resolution, into the NASA Monsoon-Asia Integrated Regional Study (MAIRS) Data Center. The data will be available for analysis and visualization in the Giovanni data system. It discusses the NASA MAIRS Data Center, presents an introduction to the data access tools, and an introduction of Products available from the service, discusses the higher resolution Land Surface Temperature (LST) and presents preliminary results of LST Trends over China.

  10. Systems and methods for coating conduit interior surfaces utilizing a thermal spray gun with extension arm

    Science.gov (United States)

    Moore, Karen A.; Zatorski, Raymond A.

    2005-07-12

    Systems and methods for applying a coating to an interior surface of a conduit. In one embodiment, a spray gun configured to apply a coating is attached to an extension arm which may be inserted into the bore of a pipe. The spray gun may be a thermal spray gun adapted to apply a powder coating. An evacuation system may be used to provide a volume area of reduced air pressure for drawing overspray out of the pipe interior during coating. The extension arm as well as the spray gun may be cooled to maintain a consistent temperature in the system, allowing for more consistent coating.

  11. Utility of tantalum (Ta) coating to improve surface hardness in vitro bioactivity and biocompatibility of Co–Cr

    Energy Technology Data Exchange (ETDEWEB)

    Pham, Vuong-Hung [WCU Hybrid Materials Program, Department of Materials Science and Engineering, Seoul National University, Seoul, 151-742 (Korea, Republic of); Advanced Institute for Science and Technology (AIST), Hanoi University of Science and Technology (HUST), No 1, Dai Co Viet Road, Ha Noi (Viet Nam); Lee, Seung-Hee; Li, Yuanlong; Kim, Hyoun-Ee [WCU Hybrid Materials Program, Department of Materials Science and Engineering, Seoul National University, Seoul, 151-742 (Korea, Republic of); Shin, Kwan-Ha [Department of Dental Laboratory Science and Engineering, Korea University, Seoul, 136-703 (Korea, Republic of); Koh, Young-Hag, E-mail: kohyh@korea.ac.kr [Department of Dental Laboratory Science and Engineering, Korea University, Seoul, 136-703 (Korea, Republic of)

    2013-06-01

    This study reports the utility of tantalum (Ta) coating for improving the surface hardness, in vitro bioactivity and biocompatibility of Co–Cr implants. The use of direct current sputtering allowed for the deposition of a dense and uniform Ta film onto a Co–Cr substrate, which was composed of β-phase Ta grains. This hard Ta coating significantly improved the surface hardness of the Co–Cr by a factor of > 2.3. In addition, the Ta-deposited Co–Cr substrate showed a vigorous precipitation of apatite crystals on its surface after 4 weeks of immersion in simulated body fluid, suggesting its excellent in vitro bioactivity. This bioactive Ta coating led to a considerable improvement in the in vitro biocompatibility of the Co–Cr, which was assessed in terms of the attachment, proliferation and differentiation of pre-osteoblasts (MC3T3-E1). - Highlights: • Dense and uniform Ta film was deposited onto a Co–Cr substrate using DC sputtering. • The Ta coating significantly enhanced the surface hardness of the Co–Cr. • The in vitro biocompatibility of the Co–Cr was also significantly improved.

  12. Utility of tantalum (Ta) coating to improve surface hardness in vitro bioactivity and biocompatibility of Co–Cr

    International Nuclear Information System (INIS)

    Pham, Vuong-Hung; Lee, Seung-Hee; Li, Yuanlong; Kim, Hyoun-Ee; Shin, Kwan-Ha; Koh, Young-Hag

    2013-01-01

    This study reports the utility of tantalum (Ta) coating for improving the surface hardness, in vitro bioactivity and biocompatibility of Co–Cr implants. The use of direct current sputtering allowed for the deposition of a dense and uniform Ta film onto a Co–Cr substrate, which was composed of β-phase Ta grains. This hard Ta coating significantly improved the surface hardness of the Co–Cr by a factor of > 2.3. In addition, the Ta-deposited Co–Cr substrate showed a vigorous precipitation of apatite crystals on its surface after 4 weeks of immersion in simulated body fluid, suggesting its excellent in vitro bioactivity. This bioactive Ta coating led to a considerable improvement in the in vitro biocompatibility of the Co–Cr, which was assessed in terms of the attachment, proliferation and differentiation of pre-osteoblasts (MC3T3-E1). - Highlights: • Dense and uniform Ta film was deposited onto a Co–Cr substrate using DC sputtering. • The Ta coating significantly enhanced the surface hardness of the Co–Cr. • The in vitro biocompatibility of the Co–Cr was also significantly improved

  13. Integrated-Optics Components Utilizing Long-Range Surface Plasmon Polaritons

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra

    2004-01-01

    This thesis describes a new class of components for integrated optics, based on the propagation of long-range surface plasmon polaritons (LR-SPPs) along metal stripes embedded in a dielectric. These novel components can provide guiding of light as well as coupling and splitting from/into a number...... fabricated and optically characterized. At 1570 nm, coupling lengths of 1.9 and 0.8 mm are found for directional couplers with waveguides separated 4 and 0 µm, respectively. LR-SPP-based waveguides and waveguide components are modeled using the effective-refractive-index method and a good agreement...... with experimental results is obtained. The interaction of LR-SPPs with photonic crystals (PCs) is also studied. The PC structures are formed by periodic arrays of gold bumps that are arranged in a triangular lattice and placed symmetrically on both sides of a thin gold film. The LR-SPP transmission through...

  14. The Mobile Surface Contamination Monitor II environmental radiological characterization utilizing GPS/GIS technologies

    International Nuclear Information System (INIS)

    Wendling, M.A.

    1993-05-01

    Time, cost, and most importantly quality of data are the three factors to measure the success of field radiological characterizations. The application of coupling radiation detection instrumentation to a GPS receiver has dramatically increased the data quality achievable compared to traditional environmental radiological survey methods. Improvements in verifying adequate spatial coverage of an area while collecting data and at,the same time reducing field time requirements can be realized. Data acquired during the recent implementation of the Mobile Surface Contamination Monitor 11 (MSCM-11) will be presented to demonstrate the advantages of this system over traditional radiological survey methods. The comparison will include time and manpower requirements. Linking the complimentary GPS, GIS and radiation detection technologies on a mobile tractor based platform has provided a tool to provide radiological characterization data faster, cheaper, and better to assist in the Environmental Restoration Mission of the Hanford Site

  15. Utility of the surface electrocardiogram for confirming right ventricular septal pacing: validation using electroanatomical mapping.

    Science.gov (United States)

    Burri, Haran; Park, Chan-Il; Zimmermann, Marc; Gentil-Baron, Pascale; Stettler, Carine; Sunthorn, Henri; Domenichini, Giulia; Shah, Dipen

    2011-01-01

    When targeting the interventricular septum during pacemaker implantation, the lead may inadvertently be positioned on the anterior wall due to imprecise fluoroscopic landmarks. Surface electrocardiogram (ECG) criteria of the paced QRS complex (e.g. negativity in lead I) have been proposed to confirm a septal position, but these criteria have not been properly validated. Our aim was to investigate whether the paced QRS complex may be used to confirm septal lead position. Anatomical reconstruction of the right ventricle was performed using a NavX® system in 31 patients (70 ± 11 years, 26 males) to validate pacing sites. Surface 12-lead ECGs were analysed by digital callipers and compared while pacing from a para-Hissian position, from the mid-septum, and from the anterior free wall. Duration of the QRS complex was not significantly shorter when pacing from the mid-septum compared with the other sites. QRS axis was significantly less vertical during mid-septal pacing (18 ± 51°) compared with para-Hissian (38 ± 37°, P = 0.028) and anterior (53 ± 55°, P = 0.003) pacing, and QRS transition was intermediate (4.8 ± 1.3 vs. 3.8 ± 1.3, P < 0.001, and vs. 5.4 ± 0.9, P = 0.045, respectively), although no cut-offs could reliably distinguish sites. A negative QRS or the presence of a q-wave in lead I tended to be more frequent with anterior than with mid-septal pacing (9/31 vs. 3/31, P = 0.2 and 8/31 vs. 1/31, P = 1.0, respectively). No single ECG criterion could reliably distinguish pacing the mid-septum from the anterior wall. In particular, a negative QRS complex in lead I is an inaccurate criterion for validating septal pacing.

  16. Optical 3D Deformation Measurement Utilizing Non-planar Surface for the Development of an “Intelligent Tire”

    Science.gov (United States)

    Matsuzaki, Ryosuke; Hiraoka, Naoki; Todoroki, Akira; Mizutani, Yoshihiro

    Intelligent tires, also known as smart tires, are equipped with sensors to monitor the strain of the interior surface and the rolling radius of tire, and are expected to improve the reliability of tires and tire control systems such as anti-lock braking systems (ABS). However, the high stiffness of an attached sensor like a strain gauge causes sensors to debond from the tire rubber. In the present study, a novel optical method is used for the concurrent monitoring of in-plane strain and out-of-plane displacement (rolling radius) utilizing the non-planar surface of the monitoring object. The optical method enables noncontact measurement of strain distribution. The in-plane strain and out-of-plane displacement are calculated by using image processing with an image of the interior surface of a tire that is taken with a single CCD camera fixed on the wheel rim. This new monitoring system is applied to an aluminum beam and a commercially available radial tire. As a result, the monitoring system provides concurrent measurement of in-plane strain, out-of-plane displacement and tire pressure, and is shown to be an effective monitoring system for intelligent tires.

  17. The Impact of Impoundment on Mercury Bioaccumulation in Fish Downstream from a Newly Constructed Reservoir, Wujiang River, Southwest China.

    Science.gov (United States)

    Li, Sixin; Zhou, Lianfeng; Chang, Jianbo; Yang, Zhi; Hu, Juxiang; Hongjun, Wang

    2017-11-01

    Mercury concentrations in fish were investigated downstream from a newly impounded subtropical reservoir in August 2008. After 6-7 months of reservoir impoundment, mean mercury concentration in fish from downstream is significantly increased by 1.9 times. Not only carnivorous fish but also benthic fish had significantly higher total mercury concentrations than others. No significant correlation was found between total mercury concentrations and body length or weight of 13 fish species. Compared with the pre-impoundment, total mercury in fish from downstream is significantly increased by reservoir impoundment, but the increased rate is lower than those in subarctic and temperate areas. Fish samples surpassed the Chinese hygienic standard for tolerances of mercury in foods increased by 4.3%. More attention should be given to fish mercury levels from downstream sites to prevent possible adverse effects on the health of local people.

  18. Aquatic impacts of an environmental disaster in a relatively pristine watershed: the breach of the Mount Polley Mine tailings impoundment, British Columbia, Canada

    Science.gov (United States)

    Owens, Philip; Petticrew, Ellen; Albers, Sam

    2015-04-01

    On 4th August 2014, the tailings impoundment of the Mount Polley copper and gold mine in British Columbia failed. Material from the impoundment (surface area = 2.7 km2) flowed into nearby Polley Lake and Hazeltine Creek, before discharging into Quesnel Lake, a large (ca. 100 km long, >500 m deep), relatively pristine lake. Estimates suggest that approximately 25 Mm3 of tailings (water and solids), in addition to eroded soils and surficial materials from Hazeltine Creek, were delivered to Quesnel Lake, raising the lake by 7.7 cm. Much of this material was deposited at the bottom of Quesnel Lake but a large plume of fine-grained sediment (d50 of ca. 1 µm) moved both up-lake towards important salmon spawning areas and down-lake into Quesnel River, which in turn flows into the Fraser River. This movement of the sediment plume is controlled by the physical limnology of the lake, especially seiche events. Samples of lake water and sediment samples taken from the impacted area show elevated levels of metals and other elements, which may have important implications for the ecosystem in this watershed (>11,000 km2). This presentation describes the failure and presents preliminary findings of the aquatic impacts of this environmental disaster.

  19. Rock riprap design methods and their applicability to long-term protection of uranium mill tailings impoundments

    International Nuclear Information System (INIS)

    Walters, W.H.

    1982-08-01

    This report reviews the more accepted or recommended riprap design methods currently used to design rock riprap protection against soil erosion by flowing water. The basic theories used to develop the various methods are presented. The Riprap Design with Safety Factors Method is identified as the logical choice for uranium mill tailings impoundments. This method is compared to the other methods and its applicability to the protection requirements of tailings impoundments is discussed. Other design problems are identified and investigative studies recommended

  20. Geomorphological assessment of sites and impoundments for the long term containment of uranium mill tailings in the Alligator Rivers Region

    International Nuclear Information System (INIS)

    East, T.J.

    1986-01-01

    This paper presents a program of current and future research into those geomorphological processes likely to affect the long term containment of uranium mill tailings in the Alligator Rivers Region of the Northern Territory. Research is directed at three main areas: identification of geomorphic hazards at proposed impoundment sites; determination of erosion rates on impoundment slopes; and prediction of patterns of fluvial dispersal of released tailings. Each necessitates consideration of present and future geomorphic processes

  1. Lung segmentation refinement based on optimal surface finding utilizing a hybrid desktop/virtual reality user interface.

    Science.gov (United States)

    Sun, Shanhui; Sonka, Milan; Beichel, Reinhard R

    2013-01-01

    Recently, the optimal surface finding (OSF) and layered optimal graph image segmentation of multiple objects and surfaces (LOGISMOS) approaches have been reported with applications to medical image segmentation tasks. While providing high levels of performance, these approaches may locally fail in the presence of pathology or other local challenges. Due to the image data variability, finding a suitable cost function that would be applicable to all image locations may not be feasible. This paper presents a new interactive refinement approach for correcting local segmentation errors in the automated OSF-based segmentation. A hybrid desktop/virtual reality user interface was developed for efficient interaction with the segmentations utilizing state-of-the-art stereoscopic visualization technology and advanced interaction techniques. The user interface allows a natural and interactive manipulation of 3-D surfaces. The approach was evaluated on 30 test cases from 18 CT lung datasets, which showed local segmentation errors after employing an automated OSF-based lung segmentation. The performed experiments exhibited significant increase in performance in terms of mean absolute surface distance errors (2.54±0.75 mm prior to refinement vs. 1.11±0.43 mm post-refinement, p≪0.001). Speed of the interactions is one of the most important aspects leading to the acceptance or rejection of the approach by users expecting real-time interaction experience. The average algorithm computing time per refinement iteration was 150 ms, and the average total user interaction time required for reaching complete operator satisfaction was about 2 min per case. This time was mostly spent on human-controlled manipulation of the object to identify whether additional refinement was necessary and to approve the final segmentation result. The reported principle is generally applicable to segmentation problems beyond lung segmentation in CT scans as long as the underlying segmentation utilizes the

  2. Restoration of Tidal Flow to Impounded Salt Marsh Exerts Mixed Effect on Leaf Litter Decomposition

    Science.gov (United States)

    Henry, B. A.; Schade, J. D.; Foreman, K.

    2015-12-01

    Salt marsh impoundments (e.g. roads, levees) disconnect marshes from ocean tides, which impairs ecosystem services and often promotes invasive species. Numerous restoration projects now focus on removing impoundments. Leaf litter decomposition is a central process in salt marsh carbon and nutrient cycles, and this study investigated the extent to which marsh restoration alters litter decomposition rates. We considered three environmental factors that can potentially change during restoration: salinity, tidal regime, and dominant plant species. A one-month field experiment (Cape Cod, MA) measured decay of litter bags in impounded, restored, and natural marshes under ambient conditions. A two-week lab experiment measured litter decay in controlled incubations under experimental treatments for salinity (1ppt and 30 ppt), tidal regime (inundated and 12 hr wet-dry cycles), and plant species (native Spartina alterniflora and invasive Phragmites australis). S. alterniflora decomposed faster in situ than P. australis (14±1.0% mass loss versus 0.74±0.69%). Corroborating this difference in decomposition, S. alterniflora supported greater microbial respiration during lab incubation, measured as CO2 flux from leaf litter and biological oxygen demand of water containing leached organic matter (OM). However, nutrient analysis of plant tissue and leached OM show P. australis released more nitrogen than S. alterniflora. Low salinity treatments in both lab and field experiments decayed more rapidly than high salinity treatments, suggesting that salinity inhibited microbial activity. Manipulation of inundation regime did not affect decomposition. These findings suggest the reintroduction of tidal flow to an impounded salt marsh can have mixed effects; recolonization by the native cordgrass could supply labile OM to sediment and slow carbon sequestration, while an increase in salinity might inhibit decomposition and accelerate sequestration.

  3. Effects of river impoundment on ecosystem services of large tropical rivers: embodied energy and market value of artisanal fisheries.

    Science.gov (United States)

    Hoeinghaus, David J; Agostinho, Angelo A; Gomes, Luiz C; Pelicice, Fernando M; Okada, Edson K; Latini, João D; Kashiwaqui, Elaine A L; Winemiller, Kirk O

    2009-10-01

    Applying the ecosystem services concept to conservation initiatives or in managing ecosystem services requires understanding how environmental impacts affect the ecology of key species or functional groups providing the services. We examined effects of river impoundments, one of the leading threats to freshwater biodiversity, on an important ecosystem service provided by large tropical rivers (i.e., artisanal fisheries). The societal and economic importance of this ecosystem service in developing countries may provide leverage to advance conservation agendas where future impoundments are being considered. We assessed impoundment effects on the energetic costs of fisheries production (embodied energy) and commercial market value of the artisanal fishery of the Paraná River, Brazil, before and after formation of Itaipu Reservoir. High-value migratory species that dominated the fishery before the impoundment was built constituted a minor component of the contemporary fishery that is based heavily on reservoir-adapted introduced species. Cascading effects of river impoundment resulted in a mismatch between embodied energy and market value: energetic costs of fisheries production increased, whereas market value decreased. This was partially attributable to changes in species functional composition but also strongly linked to species identities that affected market value as a result of consumer preferences even when species were functionally similar. Similar trends are expected in other large tropical rivers following impoundment. In addition to identifying consequences of a common anthropogenic impact on an important ecosystem service, our assessment provides insight into the sustainability of fisheries production in tropical rivers and priorities for regional biodiversity conservation.

  4. A Test of the Serial Discontinuity Concept Using Pre- and Post-Impoundment Data: do Ecosystems Recover?

    Science.gov (United States)

    Powell, H.; Jackson, L.; Culp, J.

    2005-05-01

    Many rivers are influenced by human-made impoundments that alter natural habitat. Changes in habitat hold potential consequences for biotic community structure and ecosystem function. The serial discontinuity concept (SDC), however, predicts that riverine process and function will recover downstream from an impoundment via tributary inputs. Unfortunately, rivers rarely exist in the context assumed by the SDC. Often, watersheds include multiple impoundments and other flow-altering structures. We present preliminary data and future research goals to investigate the changes in riverine habitat and benthic community structure before and after impoundment over 400 km of the Oldman River, southern Alberta, Canada. Habitat characteristics and benthic invertebrate abundance and community structure prior to dam construction were tested against post-impoundment data. Results indicate that 15 years after impoundment, flow and sediment regimes have not recovered. There is a significant decline in discharge during high flow periods below the dam and a pattern of decreased sediment transport and increased retention below the dam. Initial results have serious implications to benthic invertebrates, many of which require cobble substrates for colonization. The preliminary results on habitat alteration below the Oldman Dam do not support the predictions of the SDC.

  5. The geo-environmental design of a coal refuse impoundment in Illinois

    International Nuclear Information System (INIS)

    Ripp, B.J.

    1997-01-01

    The coal refuse impoundment discussed was one of the first permitted under new regulatory standards within the State of Illinois. The new standards go beyond the geotechnial stability of the structure and must address the groundwater quality of the area and the impact of the impoundment on the groundwater system. The geotechnial design of the coal refuse impoundment dam and associated structures had its own particular challenges such as: 1) the construction of the structure over mined workings; 2) the close proximity of seismically active fault zones; and 3) the embankment configuration being controlled by the material balance of the mine refuse. The implementation of the groundwater protection plan included: 1) incorporating the groundwater quality standards and sampling protocols of several state agencies while the standards were being drafted; 2) sampling of the potential sources of groundwater impact; 3) establishing background levels; and 4) establishing the groundwater class. An initial groundwater transport model was developed and used as the basis for recommending a groundwater monitoring design in place of constructing a soil or synthetic liner. 15 refs., 2 figs., 3 tabs

  6. Dose assessment of remedial action for uranium tailing impoundment of a nuclear factory

    International Nuclear Information System (INIS)

    Li Xutong; Ma Ruwei; Guo Zede

    2000-01-01

    A large uranium tailing impoundment in China will be closure and remedial action have been planned. The remedial action will include shaping and covering the dam and beach in order to prevent the impoundment from damage and restrict spread of tailing sands and emission of radon. The author presents the analysis and estimation of the exposure to workers for remedial action and to public after the remedial action. To estimate the exposure to workers, the pathway of inhalation of radon, tailing sands in suspension and external γ exposure were taken into consideration. The exposure scenario is considered as probably maximum exposure to the workers who work on the tailing pile without any protection measures, the dose is 6.0 mSv/a. Two situation for the exposure to public after remedial action were considered: normal and abnormal condition. For the normal condition, inhalation of radon emitted from impoundment is only the pathway to public for the exposure, and individual dose for critical group of public is 0.053 mSv/a, collective dose for population within 80 km is 1.0 man·Sv/a. For the abnormal conditions, four scenarios were considered, i.e. dwelling on tailing pile, farming on tailing pile, living in a house built by contaminated materials and some temporal activities on the pile. The scenarios of dwellings is living in a house on the pile and drinking contaminated water. The maximum individual dose is 27 mSv/a

  7. Microwave-assisted fibrous decoration of mPE surface utilizing Aloe vera extract for tissue engineering applications.

    Science.gov (United States)

    Balaji, Arunpandian; Jaganathan, Saravana Kumar; Supriyanto, Eko; Muhamad, Ida Idayu; Khudzari, Ahmad Zahran Md

    2015-01-01

    Developing multifaceted, biocompatible, artificial implants for tissue engineering is a growing field of research. In recent times, several works have been reported about the utilization of biomolecules in combination with synthetic materials to achieve this process. Accordingly, in this study, the ability of an extract obtained from Aloe vera, a commonly used medicinal plant in influencing the biocompatibility of artificial material, is scrutinized using metallocene polyethylene (mPE). The process of coating dense fibrous Aloe vera extract on the surface of mPE was carried out using microwaves. Then, several physicochemical and blood compatibility characterization experiments were performed to disclose the effects of corresponding surface modification. The Fourier transform infrared spectrum showed characteristic vibrations of several active constituents available in Aloe vera and exhibited peak shifts at far infrared regions due to aloe-based mineral deposition. Meanwhile, the contact angle analysis demonstrated a drastic increase in wettability of coated samples, which confirmed the presence of active components on glazed mPE surface. Moreover, the bio-mimic structure of Aloe vera fibers and the influence of microwaves in enhancing the coating characteristics were also meticulously displayed through scanning electron microscopy micrographs and Hirox 3D images. The existence of nanoscale roughness was interpreted through high-resolution profiles obtained from atomic force microscopy. And the extent of variations in irregularities was delineated by measuring average roughness. Aloe vera-induced enrichment in the hemocompatible properties of mPE was established by carrying out in vitro tests such as activated partial thromboplastin time, prothrombin time, platelet adhesion, and hemolysis assay. In conclusion, the Aloe vera-glazed mPE substrate was inferred to attain desirable properties required for multifaceted biomedical implants.

  8. Pre- and post-impoundment nitrogen in the lower Missouri River

    Science.gov (United States)

    Blevins, Dale W.; Wilkison, Donald H.; Niesen, Shelley L.

    2013-01-01

    Large water-sample sets collected from 1899 through 1902, 1907, and in the early 1950s allow comparisons of pre-impoundment and post-impoundment (1969 through 2008) nitrogen concentrations in the lower Missouri River. Although urban wastes were not large enough to detectably increase annual loads of total nitrogen at the beginning of the 20th century, carcass waste, stock-yard manure, and untreated human wastes measurably increased ammonia and organic-nitrogen concentrations during low flows. Average total-nitrogen concentrations in both periods were about 2.5 mg/l, but much of the particulate-organic nitrogen, which was the dominant form of nitrogen around 1900, has been replaced by nitrate. This change in speciation was caused by the nearly 80% decrease in suspended-sediment concentrations that occurred after impoundment, modern agriculture, drainage of riparian wetlands, and sewage treatment. Nevertheless, bioavailable nitrogen has not been low enough to limit primary production in the Missouri River since the beginning of the 20th century. Nitrate concentrations have increased more rapidly from 2000 through 2008 (5 to 12% per year), thus increasing bioavailable nitrogen delivered to the Mississippi River and affecting Gulf Coast hypoxia. The increase in nitrate concentrations with distance downstream is much greater during the post-impoundment period. If strategies to decrease total-nitrogen loads focus on particulate N, substantial decreases will be difficult because particulate nitrogen is now only 23% of total nitrogen in the Missouri River. A strategy aimed at decreasing particulates also could further exacerbate land loss along the Gulf of Mexico, which has been sediment starved since Missouri River impoundment. In contrast, strategies or benchmarks aimed at decreasing nitrate loads could substantially decrease nitrogen loadings because nitrates now constitute over half of the Missouri's nitrogen input to the Mississippi. Ongoing restoration and creation

  9. Mercury content in fish from newly impounded reservoirs

    International Nuclear Information System (INIS)

    Frick, K.

    1992-12-01

    During the seventies elevated mercury content in fish was observed in newly created reservoirs although background levels were normal. The initial rise of reservoir mercury levels is probably caused by the dramatically increased amount of organic matter originating from flooded top-soil and vegetation. Mercury is introduced in the food-chain by methylating bacteria that utilize the surplus of organic matter. This microbial methylation is probably also favoured by reductions in oxygen content and pH that accompanies the decomposition of organic material. It is difficult to make reliable estimates of the duration and maximum levels of the elevated mercury levels since the end result is affected by several biological and chemical processes in combination. Variations may occur on the basis of the type and amount of flooded organic and inorganic material, water chemistry, specific combination of fish and residence time of reservoir water. All available preventive and ameliorating measures are untried in reservoir water bodies, at least in large scale experiments. Vegetation and top-soil stripping could be efficient but also very costly. Liming is a possible method in cases of ongoing or expected acidification. Addition of selenium is a potentially powerful way of lowering the mercury content in fish and this method is well suited to neutral water bodies. Large reductions in fish mercury content have been documented, but since selenium also has been shown to have strong negative effects on biota this method is not yet recommended. (57 refs.)

  10. Sediment transport to and from small impoundments in northeast Kansas, March 2009 through September 2011

    Science.gov (United States)

    Foster, Guy M.; Lee, Casey J.; Ziegler, Andrew C.

    2012-01-01

    The U.S. Geological Survey, in cooperation with the Kansas Water Office, investigated sediment transport to and from three small impoundments (average surface area of 0.1 to 0.8 square miles) in northeast Kansas during March 2009 through September 2011. Streamgages and continuous turbidity sensors were operated upstream and downstream from Atchison County, Banner Creek, and Centralia Lakes to study the effect of varied watershed characteristics and agricultural practices on sediment transport in small watersheds in northeast Kansas. Atchison County Lake is located in a predominantly agricultural basin of row crops, with wide riparian buffers along streams, a substantial amount of tile drainage, and numerous small impoundments (less than 0.05 square miles; hereafter referred to as “ponds”). Banner Creek Lake is a predominantly grassland basin with numerous small ponds located in the watershed, and wide riparian buffers along streams. Centralia Lake is a predominantly agricultural basin of row crops with few ponds, few riparian buffers along streams, and minimal tile drainage. Upstream from Atchison County, Banner Creek, and Centralia Lakes 24, 38, and 32 percent, respectively, of the total load was transported during less than 0.1 percent (approximately 0.9 days) of the time. Despite less streamflow in 2011, larger sediment loads during that year indicate that not all storm events transport the same amount of sediment; larger, extreme storms during the spring may transport much larger sediment loads in small Kansas watersheds. Annual sediment yields were 360, 400, and 970 tons per square mile per year at Atchison County, Banner, and Centralia Lake watersheds, respectively, which were less than estimated yields for this area of Kansas (between 2,000 and 5,000 tons per square mile per year). Although Centralia and Atchison County Lakes had similar percentages of agricultural land use, mean annual sediment yields upstream from Centralia Lake were about 2.7 times

  11. Leucine, starch and bicarbonate utilization by specific bacterial groups in surface shelf waters off Galicia (NW Spain).

    Science.gov (United States)

    Teira, E; Hernando-Morales, V; Guerrero-Feijóo, E; Varela, M M

    2017-06-01

    The capability of different bacterial populations to degrade abundant polymers, such as algal-derived polysaccharides, or to utilize preferentially polymers over monomers, remains largely unknown. In this study, microautoradiography was combined with fluorescence in situ hybridization (MAR-FISH) to evaluate the ability of Bacteroidetes, SAR11, Roseobacter spp., Gammaproteobacteria and SAR86 cells to use bicarbonate, leucine and starch under natural light conditions at two locations in shelf surface waters off NW Spain. The percentage of cells incorporating bicarbonate was relatively high (mean 32% ± 4%) and was positively correlated with the intensity of solar radiation. The proportion of cells using starch (mean 56% ± 4%) or leucine (mean 47% ± 4%) was significantly higher than that using bicarbonate. On average, SAR11, Roseobacter spp. and Gammaproteobacteria showed a similarly high percentage of cells using leucine (47%-65% of hybridized cells) than using starch (51%-64% of hybridized cells), while Bacteroidetes and SAR86 cells preferentially used starch (53% of hybridized cells) over leucine (34%-40% of hybridized cells). We suggest that the great percentage of bacteria using starch is related to a high ambient availability of polymers associated to algal cell lysis, which, in turn, weakens the short-term coupling between phytoplankton release and bacterial production. © 2017 Society for Applied Microbiology and John Wiley & Sons Ltd.

  12. Optimization of polyhydroxybutyrate production utilizing waste water as nutrient source by Botryococcus braunii Kütz using response surface methodology.

    Science.gov (United States)

    Kavitha, Ganapathy; Kurinjimalar, Chidambaram; Sivakumar, Krishnan; Kaarthik, Muthukumar; Aravind, Rajamani; Palani, Perumal; Rengasamy, Ramasamy

    2016-12-01

    Investigations have been made to optimize various factors including pH, temperature, and substrate for enhanced polyhydroxybutyrate (PHB) production in Botryococcus braunii which serves as a pioneer for production of bioplastic (PHB). Polyhydroxybutyrate is a natural, decomposable polymers accumulated by the microorganism under different nutritional condition. Strain selection was done by staining method using Sudan black and Nile red dye. Using response surface methodology (RSM), three level- three variables Box Behnken design (BBD), the best potential combination of pH (4-11), temperature (30-50°C) and sewage waste water as substrate fed at different concentrations at 20%-100% for maximum PHB production was investigated. Maximum yield (247±0.42mg/L) of PHB dry weight was achieved from the 60% concentration of sewage waste water as a growth medium at pH 7.5 at 40°C. It was well in close agreement with the value predicted by RSM model yield (246± 0.32mg/L). Thus the study shows the production of PHB by B. braunii along with the basic characterization of PHB by using FTIR and TEM analysis. These preliminary studies indicated that PHB can also be produced by B. braunii utilizing waste water. There is no report on the optimization of PHB production in this microalgae have been documented. Copyright © 2016 Elsevier B.V. All rights reserved.

  13. Microseismic Monitoring and 3D Finite Element Analysis of the Right Bank Slope, Dagangshan Hydropower Station, during Reservoir Impounding

    Science.gov (United States)

    Liu, Xingzong; Tang, Chun'an; Li, Lianchong; Lv, Pengfei; Liu, Hongyuan

    2017-07-01

    The right bank slope of Dagangshan hydropower station in China has complex geological conditions and is subjected to high in situ stress. Notably, microseismic activities in the right bank slope occurred during reservoir impounding. This paper describes the microseismic monitoring technology, and three-dimensional (3D) finite element analysis is used to explore the microseismic activities and damage mechanisms in the right bank slope during reservoir impounding. Based on data obtained from microseismic monitoring, a progressive microseismic damage model is proposed and implemented for 3D finite element analysis. The safety factor for the right bank slope after reservoir impoundment obtained from the 3D finite element analysis, which included the effects of progressive microseismic damage, was 1.10, indicating that the slope is stable. The microseismic monitoring system is able to capture the slope disturbance during reservoir impounding in real time and is a powerful tool for qualitatively assessing changes in slope stability over time. The proposed progressive microseismic damage model adequately simulates the changes in the slope during the impoundment process and provides a valuable tool for evaluating slope stability.

  14. Cumulative impoundment evaporation in water resource management within the mid-Atlantic: A case study in Virginia

    Science.gov (United States)

    Scott, D.; Burgholzer, R.; Kleiner, J.; Brogan, C. O.; Julson, C.; Withers, E.

    2017-12-01

    Across the eastern United States, successful management of water resources to satisfy the competing demands for human consumption, industry, agriculture, and ecosystems requires both water quality and water quantity considerations. Over the last 2 decades, low streamflows during dry summers have increased scrutiny on water supply withdrawals. Within Virginia, a statewide hydrologic model provides quantitative assessments on impacts from proposed water withdrawals to downstream river flow. Currently, evaporative losses are only accounted for from the large reservoirs. In this study, we sought to provide a baseline estimate for the cumulative evaporation from impoundments across all of the major river basins in Virginia. Virginia provides an ideal case study for the competing water demands in the mid-Atlantic region given the unique tracking of water withdrawals throughout the river corridor. In the over 73,000 Virginia impoundments, the cumulative annual impoundment evaporation was 706 MGD, or 49% of the permitted water withdrawal. The largest reservoirs (>100 acres) represented over 400 MGD, and 136 MGD for the smaller impoundments (planning will require not only understanding evaporation within large reservoirs, but also the thousands of small impoundments across the landscape.

  15. Geomorphological assessment of sites and impoundments for the long term containment of uranium mill tailings in the Alligator Rivers Region

    International Nuclear Information System (INIS)

    East, T.J.

    1985-01-01

    Current and future research into the geomorphological processes likely to affect the long term containment of uranium mill tailings in the Alligator Rivers Region is directed at three main areas: identification of geomorphic hazards at proposed impoundment sites; determination of erosion rates on impoundment slopes; and prediction of patterns of fluvial dispersal of released tailings. Each necessitates consideration of present and future geomorphic processes. Process rates during the next few thousand years might be predictable by extrapolation of contemporary and past (i.e. Holocene) climates, sea-levels and depositional environments, evidence for which is preserved in the sedimentary record. In current projects, the Late Quarternary stratigraphy of Magela Creek are examined to provide data for modelling of present and future sedimentological processes. Site stability evaluation entails recognition of present and future geomorphic hazards at impoundment sites, and includes fluvial and hillslope erosion, extreme flood events and mass movements. The life of a tailings impoundment is further determined by the intensity of erosional processes acting upon its slopes and their cover materials. A knowledge of present and future erosion rates will allow the optimisation of slope characteristics and materials in the impoundment design

  16. 40 CFR 270.17 - Specific part B information requirements for surface impoundments.

    Science.gov (United States)

    2010-07-01

    ... the leak detection system; (4) The construction quality assurance (CQA) plan if required under § 264... he will provide such a certification upon completion of construction in accordance with the plans and... under § 270.14(b)(7); (f) A description of how hazardous waste residues and contaminated materials will...

  17. 75 FR 64974 - Notice of Data Availability on Coal Combustion Residual Surface Impoundments

    Science.gov (United States)

    2010-10-21

    ... contained in the company responses has been inserted into a database. All the fields and entries in this database have been extracted and posted in the docket as PDF and Microsoft Excel spreadsheets which enable...

  18. Development of a dust deposition forecast model for a mine tailings impoundment

    Science.gov (United States)

    Stovern, Michael

    Wind erosion, transport and deposition of particulate matter can have significant impacts on the environment. It is observed that about 40% of the global land area and 30% of the earth's population lives in semiarid environments which are especially susceptible to wind erosion and airborne transport of contaminants. With the increased desertification caused by land use changes, anthropogenic activities and projected climate change impacts windblown dust will likely become more significant. An important anthropogenic source of windblown dust in this region is associated with mining operations including tailings impoundments. Tailings are especially susceptible to erosion due to their fine grain composition, lack of vegetative coverage and high height compared to the surrounding topography. This study is focused on emissions, dispersion and deposition of windblown dust from the Iron King mine tailings in Dewey-Humboldt, Arizona, a Superfund site. The tailings impoundment is heavily contaminated with lead and arsenic and is located directly adjacent to the town of Dewey-Humboldt. The study includes in situ field measurements, computational fluid dynamic modeling and the development of a windblown dust deposition forecasting model that predicts deposition patterns of dust originating from the tailings impoundment. Two instrumented eddy flux towers were setup on the tailings impoundment to monitor the aeolian and meteorological conditions. The in situ observations were used in conjunction with a computational fluid dynamic (CFD) model to simulate the transport of windblown dust from the mine tailings to the surrounding region. The CFD model simulations include gaseous plume dispersion to simulate the transport of the fine aerosols, while individual particle transport was used to track the trajectories of larger particles and to monitor their deposition locations. The CFD simulations were used to estimate deposition of tailings dust and identify topographic mechanisms

  19. Cyanobacteria and cyanotoxins are present in drinking water impoundments and groundwater wells in desert environments.

    Science.gov (United States)

    Chatziefthimiou, Aspassia D; Metcalf, James S; Glover, W Broc; Banack, Sandra A; Dargham, Soha R; Richer, Renee A

    2016-05-01

    Desert environments and drylands experience a drastic scarcity of water resources. To alleviate dependence on freshwater for drinking water needs, countries have invested in infrastructure development of desalination plants. Collectively, the countries of the Arabian Gulf produce 45% of the world's desalinated water, which is stored in dams, mega-reservoirs and secondary house water tanks to secure drinking water beyond daily needs. Improper storage practices of drinking water in impoundments concomitant with increased temperatures and light penetration may promote the growth of cyanobacteria and accumulation of cyanotoxins. To shed light on this previously unexplored research area in desert environments, we examined drinking and irrigation water of urban and rural environments to determine whether cyanobacteria and cyanotoxins are present, and what are the storage and transportation practices as well as the environmental parameters that best predict their presence. Cyanobacteria were present in 80% of the urban and 33% of the rural water impoundments. Neurotoxins BMAA, DAB and anatoxin-a(S) were not detected in any of the water samples, although they have been found to accumulate in the desert soils, which suggests a bioaccumulation potential if they are leached into the aquifer. A toxic BMAA isomer, AEG, was found in 91.7% of rural but none of the urban water samples and correlated with water-truck transportation, light exposure and chloride ions. The hepatotoxic cyanotoxin microcystin-LR was present in the majority of all sampled impoundments, surpassing the WHO provisional guideline of 1 μg/l in 30% of the urban water tanks. Finally, we discuss possible management strategies to improve storage and transportation practices in order to minimize exposure to cyanobacteria and cyanotoxins, and actions to promote sustainable use of limited water resources. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Relationships among catch, angler catisfaction, and fish assemblage characteristics of an urban small impoundment fishery

    Science.gov (United States)

    Ivasauskas, Tomas J.; Xiong, Wilson N.; Engman, Augustin C.; Fischer, Jesse R.; Kwak, Thomas J.; Rundle, Kirk R.

    2017-01-01

    Urban fisheries provide unique angling opportunities for people from traditionally underrepresented demographics. Lake Raleigh is a 38-ha impoundment located on the North Carolina State University campus in Raleigh. Like many urban fisheries, little is known about angler use and satisfaction or how angling catch rate is related to fish availability in Lake Raleigh. We characterized the recreational fishery and fish assemblage with concurrent creel and boat electrofishing surveys over the course of one year. In total, 245 anglers were interviewed on 68 survey days. On average, anglers spent 1.7 h fishing per trip and caught 0.385 fish h –1. A large proportion of anglers (43.9%) targeted multiple species, whereas 36.5% targeted largemouth bass (Micropterus salmoides), 10.0% targeted panfish (i.e., sunfishes [Lepomis spp.] and crappies [Pomoxis spp.]), and 9.6% targeted catfish (Ameiurus spp. and Ictalurus spp.). Most anglers (69.4%) were satisfied with their experience, and overall satisfaction was unrelated to catch rate. Pulsed-DC boat electrofishing was conducted on 25 dates, and 617 fish were sampled. Angler catch rate was unrelated to electrofishing catch rate, implying that anglers' catch rate was independent of fish density or availability. Our results demonstrate that even minimally managed urban fisheries can provide high angler satisfaction, with limited dedication of management resources. Relationships Among Catch, Angler Satisfaction, and Fish Assemblage Characteristics of an Urban Small Impoundment Fishery (PDF Download Available). Available from: https://www.researchgate.net/publication/316636550_Relationships_Among_Catch_Angler_Satisfaction_and_Fish_Assemblage_Characteristics_of_an_Urban_Small_Impoundment_Fishery [accessed Aug 11, 2017].

  1. Current status, research needs, and opportunities in applications of surface processing to transportation and utilities technologies. Proceedings of a December 1991 workshop

    Energy Technology Data Exchange (ETDEWEB)

    Czanderna, A.W.; Landgrebe, A.R. [eds.

    1992-09-01

    Goal of surface processing is to develop innovative methods of surface modification and characterization for optimum performance and environmental protection for cost-effective operational lifetimes of systems, materials, and components used in transportation and utilities. These proceedings document the principal discussions and conclusions reached at the workshop; they document chapters about the current status of surface characterization with focus on composition, structure, bonding, and atomic-scale topography of surfaces. Also documented are chapters on the current status of surface modification techniques: electrochemical, plasma-aided, reactive and nonreactive physical vapor deposition, sol-gel coatings, high-energy ion implantation, ion-assisted deposition, organized molecular assemblies, solar energy. Brief chapters in the appendices document basic research in surface science by NSF, Air Force, and DOE. Participants at the workshop were invited to serve on 10 working groups. Separate abstracts were prepared for the data base where appropriate.

  2. Geochemical and mineralogical characterization of a neutral, low-sulfide/high-carbonate tailings impoundment, Markušovce, eastern Slovakia.

    Science.gov (United States)

    Hiller, Edgar; Petrák, Marián; Tóth, Roman; Lalinská-Voleková, Bronislava; Jurkovič, L'ubomír; Kučerová, Gabriela; Radková, Anežka; Sottník, Peter; Vozár, Jaroslav

    2013-11-01

    mineral assemblage and their occurrence follows the order: chalcopyrite > pyrite > tetrahedrite>arsenopyrite. The mineralogical composition of the tailings corresponds well to the primary mineralization mined. The neutralization capacity of the tailings is high, as confirmed by the values of neutralization potential to acid generation potential ratio, ranging from 6.7 to 63.9, and neutral to slightly alkaline pH of the tailings (paste pH 7.16-8.12) and the waters (pH 7.00-8.52). This is explained by abundant occurrence of carbonate minerals in the tailings, which readily neutralize the acidity generated by sulfide oxidation. The total solid-phase concentrations of metal(loid)s decrease as Cu>Sb>Hg>As and reflect the proportions of sulfides present in the tailings. Sulfide oxidation generally extends to a depth of 2 m. μ-XRD and EMPA were used to study secondary products developed on the surface of sulfide minerals and within the tailings. The main secondary minerals identified are goethite and X-ray amorphous Fe oxyhydroxides and their occurrence decreases with increasing tailings depth. Secondary Fe phases are found as mineral coatings or individual grains and retain relatively high amounts of metal(loid)s (up to 57.6 wt% Cu, 1.60 wt% Hg, 23.8 wt% As, and 2.37 wt% Sb). Based on batch leaching tests and lysimeter results, the mobility of potentially toxic elements in the tailings is low. The limited mobility of metals and metalloids is due to their retention by Fe oxyhydroxides and low solubilities of metal(loid)-bearing sulfides. The observations are consistent with PHREEQC calculations, which predict the precipitation of Fe oxyhydroxides as the main solubility-controlling mineral phases for As, Cu, Hg, and Sb. Waters discharging from tailings impoundment are characterized by a neutral to slightly alkaline pH (7.52-7.96) and low concentrations of dissolved metal(loid)s (<5-7.0 μg/L Cu, <0.1-0.3 μg/L Hg, 5.0-16 μg/L As, and 5.0-43 μg/L Sb). Primary factors

  3. Utility of remote sensing-based surface energy balance models to track water stress in rain-fed switchgrass under dry and wet conditions

    Science.gov (United States)

    The ability of remote sensing-based surface energy balance (SEB) models to track water stress in rain-fed switchgrass has not been explored yet. In this paper, the theoretical framework of crop water stress index (CWSI) was utilized to estimate CWSI in rain-fed switchgrass (Panicum virgatum L.) usin...

  4. Impoundment of the Zipingpu reservoir and triggering of the 2008 Mw 7.9 Wenchuan earthquake, China.

    Science.gov (United States)

    Tao, Wei; Masterlark, Timothy; Shen, Zheng-Kang; Ronchin, Erika

    2015-10-01

    Impoundment of the Zipingpu reservoir (ZR), China, began in September 2005 and was followed 2.7 years later by the 2008 M w 7.9 Wenchuan earthquake (WE) rupturing the Longmen Shan Fault (LSF), with its epicenter ~12 km away from the ZR. Based on the poroelastic theory, we employ three-dimensional finite element models to simulate the evolution of stress and pore pressure due to reservoir impoundment, and its effect on the Coulomb failure stress on the LSF. The results indicate that the reservoir impoundment formed a pore pressure front that slowly propagated through the crust with fluid diffusion. The reservoir loading induced either moderate or no increase of the Coulomb failure stress at the hypocenter prior to the WE. The Coulomb failure stress, however, grew ~9.3-69.1 kPa in the depth range of 1-8 km on the LSF, which may have advanced tectonic loading of the fault system by ~60-450 years. Due to uncertainties of fault geometry and hypocenter location of the WE, it is inconclusive whether impoundment of the ZR directly triggered the WE. However, a small event at the hypocenter could have triggered large rupture elsewhere on fault, where the asperities were weakened by the ZR. The microseismicity around the ZR also showed an expanding pattern from the ZR since its impoundment, likely associated with diffusion of a positive pore pressure pulse. These results suggest a poroelastic triggering effect (even if indirectly) of the WE due to the impoundment of the ZR.

  5. An Object-Based Machine Learning Classification Procedure for Mapping Impoundments in Brazil's Amazon-Cerrado Agricultural Frontier

    Science.gov (United States)

    Solvik, K.; Macedo, M.; Graesser, J.; Lathuilliere, M. J.

    2017-12-01

    Large-scale agriculture and cattle ranching in Brazil has driving the creation of tens of thousands of small stream impoundments to provide water for crops and livestock. These impoundments are a source of methane emissions and have significant impacts on stream temperature, connectivity, and water use over a large region. Due to their large numbers and small size, they are difficult to map using conventional methods. Here, we present a two-stage object-based supervised classification methodology for identifying man-made impoundments in Brazil. First, in Google Earth Engine pixels are classified as water or non-water using satellite data and HydroSHEDS products as predictors. Second, using Python's scikit-learn and scikit-image modules the water objects are classified as man-made or natural based on a variety of shape and spectral properties. Both classifications are performed by a random forest classifier. Training data is acquired by visually identifying impoundments and natural water bodies using high resolution satellite imagery from Google Earth.This methodology was applied to the state of Mato Grosso using a cloud-free mosaic of Sentinel 1 (10m resolution) radar and Sentinel 2 (10-20m) multispectral data acquired during the 2016 dry season. Independent test accuracy was estimated at 95% for the first stage and 93% for the second. We identified 54,294 man-made impoundments in Mato Grosso in 2016. The methodology is generalizable to other high resolution satellite data and has been tested on Landsat 5 and 8 imagery. Applying the same approach to Landsat 8 images (30 m), we identified 35,707 impoundments in the 2015 dry season. The difference in number is likely because the coarser-scale imagery fails to detect small (< 900 m2) objects. On-going work will apply this approach to satellite time series for the entire Amazon-Cerrado frontier, allowing us to track changes in the number, size, and distribution of man-made impoundments. Automated impoundment mapping

  6. Horse impoundments under Control of Horses legislation in the Munster region of Ireland: factors affecting euthanasia.

    Science.gov (United States)

    Cullinane, M; O'Sullivan, E; Collins, D M; Byrne, A W; More, S J

    2015-01-24

    Recently, considerable international attention has been paid to the problem of unwanted horses. In Ireland, stray horses, particularly in urban areas, are a further problem. The Control of Horses Act 1996 was enacted in response to an ongoing problem of uncontrolled horses in public places. As yet, no research work has been conducted focusing on stray horses in Ireland. This paper describes horses impounded under the Act in the Munster region of Ireland during 2005-2012 and the factors influencing decisions regarding their disposal. A logistic regression model was developed to investigate factors influencing the probability that a horse was euthanised during impoundment. In total, 3625 seizure events were recorded, most towards the end of the study period. Predictors for euthanasia during 2010-2012 included seizure location, sex, age, colour, body condition score and year. This study highlights the problem of stray horses in Ireland, particularly in urban areas. There is a need for rigorous enforcement of newly enacted horse identification legislation, allowing a fully integrated traceability system. More is required to manage the long-established societal problems of stray horses in urban settings, with a uniform approach by all Local Authorities being long overdue. British Veterinary Association.

  7. Microcrustaceans (Branchipoda and Copepoda) of Wetland Impoundments on the Savannah River Site, Aiken, South Carolina

    Energy Technology Data Exchange (ETDEWEB)

    DeBiase, Adrienne E; Taylor, Barbara E

    2005-09-21

    The United States Department of Energy’s Savannah River Site (SRS) in Aiken, Allendale, and Barnwell Counties, South Carolina, contains an abundance of freshwater wetlands and impoundments. Four large impoundments, as well as several small, abandoned farm and mill ponds, and about 400 Carolina bays and other small, isolated depression wetland ponds are located within the 893 km2 area of the SRS. Crustaceans of the orders Branchiopoda and Copepoda are nearly ubiquitous in these water bodies. Although small in size, these organisms are often very abundant. They consequently play an important trophic role in freshwater food webs supporting fish, larval salamanders, larval insects, and numerous other animals, aquatic and terrestrial. This report provides an introduction to the free-living microcrustaceans of lentic water bodies on the SRS and a comprehensive list of species known to occur there. Occurrence patterns are summarized from three extensive survey studies, supplemented with other published and unpublished records. In lieu of a key, we provide a guide to taxonomic resources and notes on undescribed species. Taxa covered include the orders Cladocera, Anostraca, Laevicaudata, and Spinicaudata of the Subclass Branchiopoda and the Superorders Calanoida and Cyclopoida of Subclass Copepoda. Microcrustaceans of the Superorder Harpacticoida of the Subclass Copepoda and Subclass Ostracoda are also often present in lentic water bodies. They are excluded from this report because they have not received much study at the species level on the SRS.

  8. Use of special oedometer tests for the remediation of large uranium mill tailings impoundments at Wismut, Germany

    International Nuclear Information System (INIS)

    Barnekow, U.; Paul, M.

    2002-01-01

    The paper presents the use of recently developed special oedometer tests for designing the remediation of large uranium tailings ponds at WISMUT, Germany. Uranium ore mining and milling in eastern Germany by the former Soviet-German WISMUT company lasted from 1946 to 1990. Wastes from the hydrometallurgical uranium extraction processes were discharged into large tailings impoundments covering a total area of 5.5 km 2 and containing about 150 x 10 6 m 3 of uranium mill tailings. Tailings pond remediation is ongoing by in-place decommissioning with dewatering by technical means. Geotechnical properties and the most suitable so-called non-linear finite strain consolidation behaviour of fine uranium mill tailings are described. Decommissioning techniques comprise, among others, interim covering of under consolidated fine tailings, contouring of tailings surfaces and final covering. Contouring, in particular, has a huge potential for optimization in terms of cost reduction. For contouring total settlement portions, the spatial distribution of differential settlement portions and the time-dependent settlement rates, especially of the cohesive fine uranium mill tailings are of critical importance. A new special oedometer KD 314 S has been developed to generate all the input data needed to derive the fundamental geotechnical relationships of void ratio vs. effective stress and of permeability coefficient vs. void ratio for consolidation calculations. Since December 1999 the new special oedometer KD 314 S has been working successfully on fine uranium mill tailings from both acid and from soda alkaline milling. Results coincide with non-linear finite strain consolidation theory. The geotechnical functions derived were used as input parameters for consolidation modelling. An example of the consolidation modelling on Helmsdorf tailings pond is presented. (author)

  9. Relative amplitude preservation processing utilizing surface consistent amplitude correction. Part 3; Surface consistent amplitude correction wo mochiita sotai shinpuku hozon shori. 3

    Energy Technology Data Exchange (ETDEWEB)

    Saeki, T. [Japan National Oil Corporation, Tokyo (Japan). Technology Research Center

    1996-10-01

    For the seismic reflection method conducted on the ground surface, generator and geophone are set on the surface. The observed waveforms are affected by the ground surface and surface layer. Therefore, it is required for discussing physical properties of the deep underground to remove the influence of surface layer, preliminarily. For the surface consistent amplitude correction, properties of the generator and geophone were removed by assuming that the observed waveforms can be expressed by equations of convolution. This is a correction method to obtain records without affected by the surface conditions. In response to analysis and correction of waveforms, wavelet conversion was examined. Using the amplitude patterns after correction, the significant signal region, noise dominant region, and surface wave dominant region would be separated each other. Since the amplitude values after correction of values in the significant signal region have only small variation, a representative value can be given. This can be used for analyzing the surface consistent amplitude correction. Efficiency of the process can be enhanced by considering the change of frequency. 3 refs., 5 figs.

  10. The net GHG (CO2, CH4 and N2O) footprint of a newly impounded subtropical hydroelectric reservoir: Nam Theun 2

    Science.gov (United States)

    Deshmukh, Chandrashekhar; Guérin, Frédéric; Delon, Claire; Pighini, Sylvie; Vongkhamsao, Axay; Descloux, Stéphane; Chanudet, Vincent; Tardif, Raphael; Godon, Arnaud; Guédant, Pierre; Galy-Lacaux, Corinne; Zouiten, Cyril; Oliva, Priscia; Audry, Stéphane; Serça, Dominique

    2013-04-01

    There is a rising concern over the contribution of hydroelectric reservoirs to global anthropogenic greenhouse gases (GHGs) emissions. We present here the first comprehensive assessment of GHGs footprint associated with the creation of the Nam Theun 2 (NT2) hydroelectric reservoir in subtropical region of the Lao People's Democratic Republic. This assessment is the results of a monthly monitoring that have been conducted over 4 year (2008-to date). The carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O) sources and sinks were quantified before and after impoundment, which began in May 2008. Before impoundment, the landscape to be flooded was a sink of carbon dioxide (-73 ± 225 Gg CO2eq yr-1),roughly neutral in terms of methane (7 ± 11 Gg CO2eq yr-1), and a source of nitrous oxide (345 ± 158 Gg CO2eq yr-1). After impoundment, total CO2 and CH4 emissions increased and N2O emissions decreased. For the year 2010, CO2 (791 ± 54 Gg CO2eq yr-1) and CH4 (644 ± 124 Gg CO2eq yr-1) contributed equally to the total gross GHG emissions from NT2 (54 and 43% for CO2 and CH4, respectively) whereas N2O contributed only 3% (47 ± 29 Gg CO2eq yr-1). The GHG emissions remained constant in 2011. Our results indicate that most of the GHG (around 90%) were emitted from reservoir water surface and the drawdown area, and only 10% were emitted by degassing at the turbines and from diffusive emissions downstream of the turbines and the dam, a percentage lower than reported for other hydroelectric reservoirs. With a total emissions of 1482 ± 207 and 1298 ± 200 Gg CO2eq yr-1 for year 2010 and 2011, gross NT2 emissions are about an order of magnitude higher than pre-impoundment emissions (276 ± 393 Gg CO2eq yr-1). With a net GHG emissions of 1203 ± 601 (2010) and 1022 ± 594 (2011) Gg CO2eq yr-1, and an annual power generation of about 6 TWh, GHG emission factor equal to 0.20 (2010) and 0.17 (2011) Mg CO2eq MWh-1 for NT2 which is up to five times lower than the emission factor

  11. Interrelationships between fish tissue mercury concentrations and water quality for South Dakota natural lakes and impoundments

    Science.gov (United States)

    Chipps, Steven R.; Stetler, Larry; Stone, James J.; McCutcheon, Cindy M.

    2011-01-01

    The purpose of this study was to determine whether water quality parameters commonly associated with primary productivity may be used to predict the susceptibility of a specific water body to exceed proposed fish consumption advisory limitation of 0.3 mg kg−1. South Dakota currently has nine lakes and impoundments that exceed fish tissue mercury advisory limits of 1.0 mg kg−1 total mercury, far exceeding US Environmental Protection Agency and Food and Drug Administration 0.3 mg kg−1 consumption criteria. Previous studies suggest that increased aquatic productivity may mitigate the effects of biological production and subsequent uptake of methyl mercury through bio-dilution; however, it is uncertain whether these trends may exist within highly alkaline and highly productive aquatic conditions common to South Dakota lakes and impoundments. Water quality parameters and fish tissue mercury data for northern pike and walleye were collected and assessed using existing South Dakota Department of Environment and Natural Resources and Game Fish and Parks data. The data was initially screened using both parametric linear regression and non-parametric Mann–Whitney rank sum comparisons and further assessed using binary logistic regression and stepwise logistic regression methodology. Three separate phosphorus measurements (total, total dissolved, and Trophic State Index) and pH were determined to significantly correlate with increased mercury concentrations for the northern pike-in-impoundments model. However, phosphorus surprisingly was not a strong predictor for the remaining scenarios modeled. For the northern pike-in-natural lakes models, alkalinity was the most significant water quality parameter predicting increased mercury concentrations. Mercury concentrations for the walleye-in-natural lakes models were further influenced by pH and alkalinity. The water quality and fish tissue mercury interrelationships determined within this study suggest aquatic

  12. [Comparison of trophic status analysis of the Daning River within the Three Gorges Reservoir before and after experimental impoundment].

    Science.gov (United States)

    Zhang, Jia-Lei; Zheng, Bing-Hui; Liu, Lu-San; Wang, Li-Jing; Wu, Guang-Ying

    2012-10-01

    We evaluated 4-year data set to assess the trophic state and limiting factors of the Three Gorges Reservoir (TGR) during the experimental impounding period (September 2005 to September 2007) and the normal operating period (September 2008 to September 2010). The results indicated that there had been appeared new characteristics in spatial and temporal distribution of trophic state indices after impoundment. The trophic state indices (TSI(TP)) showed increased trend after the TGR impoundment during the study area, but TSI(TN) and TSI(SD) had no significant changes after the TGR impoundment. The values of TSI(CHL) showed increased trend after the TGR impoundment in S1, and the values of TSI(CHL) did not show obvious changes in S2, S3 and S4 after the TGR impoundment. The values of TSI(TN), TSI(TP) and TSI(SD) show similar spatial variances with the highest value in S4, followed in a descending order by S3, S2 and S1. TSI(CHL) in the S2 and S3 were higher than that in S1 and S4. According to the characteristics of water level, the operational period of the TGR classified into following four stages: stage I (pre-November-April), stage II (May-July), stage III (July-September) and stage IV (September-November). The values of TSI(TN) and TSI(TP) in the Daning River and the TGR mainstream showed similar seasonal variances with the highest value in the stage II and III, followed in a descending order by stage I and IV. The values of TSI(CHL) varied substantially among the four stages, with the highest value in stage III, followed by stage II, IV and I. The trophic state indices differences were getting smaller between the four stages after the TGR impoundment. Using Carlson's two-dimensional approach, deviations of the TSI(S) indicated that factors other than phosphorous and nitrogen limited algal growth and that nonalgal particles affected light attenuation. These findings were further supported by the significant correlation among the values of TSI and hydrological

  13. Geomorphological and botanical change on the Outer Slave River Delta, NWT, before and after impoundment of the Peace River

    Science.gov (United States)

    English, Michael C.; Hill, R. Brad; Stone, Micheal A.; Ormson, Ron

    1997-10-01

    This paper examines geomorphological and botanical changes on the outer low elevation portion of the Slave River Delta prior to and after impoundment of the Peace River at Hudson's Hope, British Columbia. The Slave River Delta deposits are approximately 8300 km2, about 5% (400 km2) is defined as the active delta which progrades into Great Slave Lake through an active system of distributaries. This active portion of the delta is the area studied.The Peace River provides approximately 65% of the annual flow of the Slave River. Alteration of the natural flow regime and suspended sediment load of the Slave River has resulted from the upstream impoundment. Calculations indicate that the annual suspended sediment load in the Slave River has decreased by 33%. Using aerial photographs of the Slave Delta taken in 1946 and 1966, prior to damming the Peace River, geomorphological change and the spatial changes in plant assemblages have been recorded using GIS software. Aerial photographs taken in 1977 and 1994 were used in similar fashion to document geomorphological and botanical change and rates of change after impoundment. The Outer Delta is most susceptible to hydrological and suspended sediment changes in the river system. As such it is shown that geomorphological development in these Outer Delta landforms has been notably reduced since impoundment and changes in plant assemblage distribution indicate a drier, less productive environment. Results of aerial photo analysis show that the rate of development of distinctive cleavage bar islands on the Outer Delta has been notably reduced since impoundment. Changes in plant assemblage areas on these islands indicates both an autogenic and allogenic change to a drier, less productive environment and actual loss, by erosion, of some of the most productive Equisetum assemblages.

  14. Analysis of spatial distribution and inventory of radioactivity within the uranium mill tailings impoundment

    Directory of Open Access Journals (Sweden)

    D. O. Bugai

    2015-10-01

    Full Text Available Results are presented of the characterization of radioactivity inventory of Zapadnoe uranium mill tailings impoundment situated at Pridneprovsky Chemical Plant (PChP; Dneprodzerzhinsk, Ukraine. Analyses of radioactivity data set based on analytical studies of core material from 15 characterization boreholes allowed significantly refining waste volume and radioactivity inventory estimates. Geostatistical analyses using variogram function have established that radioactivity distribution in Zapadnoe tailings is characterized by regular spatial correlation patterns. Ordinary kriging method was applied to assess distribution of radioactivity in 3D. Results of statistical analyses suggest significant redistribution of uranium in the dissolved form in the residues (presumably due to water infiltration process. The developed structural model for radioactivity distribution is used for further risk assessment analyses. Derived radioactivity correlation scales can be used for optimization of sample collection when characterizing the PChP Site and similar contaminated sites elsewhere.

  15. Chlorophyll Detection and Mapping of Shallow Water Impoundments Using Image Spectrometry

    International Nuclear Information System (INIS)

    Artigas, F.; Pechmann, I.; Marti, A.; Yao, N.; Pechmann, I.

    2008-01-01

    There exists a common perception that chlorophyll a concentrations in tidal coastal waters are unsuitable to be captured by remote sensing techniques because of high water turbidity. In this study, we use band index measurements to separate active chlorophyll pigments from other constituents in the water. Published single- and multiband spectral indices are used to establish a relationship between algal chlorophyll concentration and reflectance data. We find an index which is suitable to map chlorophyll gradients in the impoundments, ditches, and associated waterways of the Hackensack Meadow lands (NJ, USA). The resulting images clearly depict the spatial distribution of plant pigments and their relationship with the biological conditions of the waters in the estuary. Since these biological conditions are often determined by land usage, the methods in this paper provide a simple tool to address water quality management issues in fragmented urban estuaries.

  16. Long-term changes in fish assemblage following the impoundments of the Three Gorges Reservoir in Hejiang, a protected reach of the upper Yangtze River

    Directory of Open Access Journals (Sweden)

    Liu F.

    2013-03-01

    Full Text Available The construction of the Three Gorges Reservoir (TGR has seriously affected the fish assemblage in the impounded reaches. However, fish assemblage changes in the riverine zone remain poorly documented. In order to explore how upstream fish assemblage has responded to the successive impoundments of the TGR, fish investigations were conducted biannually in Hejiang, a protected reach of the upper Yangtze River, during the period from 1997 to 2011. Multivariate analysis revealed significant temporal differences in fish assemblage following the impoundments of the TGR. Prior to the impoundments, the fish assemblage appeared to be very diversified and very even. Immediately after the first and the second impoundment, the lotic species, such as Coreius guichenoti, Rhinogobio ventralis, Rhinogobio cylindricus and Coreius heterodon, became evidently dominant, due to their upstream migrations from the reservoir. However, two years after the third impoundment, the lotic species decreased dramatically, while lentic Hypophthalmichthys molitrix and Pelteobagrus vachelli became the new dominant species. Based on this and other studies, we can see the habitats of the riverine fish in the upper Yangtze River have been shrunk seriously because of the impoundments of the TGR. The cascade hydropower development in the lower Jinsha River will pose an accumulative effect on the aquatic environment in the mainstream of the upper Yangtze River. Free-flowing tributaries, such as the Chishui River, will play more important roles in fish conservation.

  17. Fishers' knowledge identifies environmental changes and fish abundance trends in impounded tropical rivers.

    Science.gov (United States)

    Hallwass, Gustavo; Lopes, Priscila F; Juras, Anastácio A; Silvano, Renato A M

    2013-03-01

    The long-term impacts of large hydroelectric dams on small-scale fisheries in tropical rivers are poorly known. A promising way to investigate such impacts is to compare and integrate the local ecological knowledge (LEK) of resource users with biological data for the same region. We analyzed the accuracy of fishers' LEK to investigate fisheries dynamics and environmental changes in the Lower Tocantins River (Brazilian Amazon) downstream from a large dam. We estimated fishers' LEK through interviews with 300 fishers in nine villages and collected data on 601 fish landings in five of these villages, 22 years after the dam's establishment (2006-2008). We compared these two databases with each other and with data on fish landings from before the dam's establishment (1981) gathered from the literature. The data obtained based on the fishers' LEK (interviews) and from fisheries agreed regarding the primary fish species caught, the most commonly used type of fishing gear (gill nets) and even the most often used gill net mesh sizes but disagreed regarding seasonal fish abundance. According to the interviewed fishers, the primary environmental changes that occurred after the impoundment were an overall decrease in fish abundance, an increase in the abundance of some fish species and, possibly, the local extinction of a commercial fish species (Semaprochilodus brama). These changes were corroborated by comparing fish landings sampled before and 22 years after the impoundment, which indicated changes in the composition of fish landings and a decrease in the total annual fish production. Our results reinforce the hypothesis that large dams may adversely affect small-scale fisheries downstream and establish a feasible approach for applying fishers' LEK to fisheries management, especially in regions with a low research capacity.

  18. Assessing the Utility of an Event-Step ASMD Model by Analysis of Surface Combatant Shared Self-Defense

    National Research Council Canada - National Science Library

    Patrick, Chase

    2001-01-01

    ... and growing availability of ASCMs makes a persuasive argument for the U.S. Navy to aggressively expand surface combatant defense systems, and perform periodic reviews of existing defensive tactics to ensure effective employment of new combat systems...

  19. Utilization of Hydrologic Remote Sensing Data in Land Surface Modeling and Data Assimilation: Current Status and Challenges

    Science.gov (United States)

    Kumar, Sujay V.; Peters-Lidard, Christa; Reichl, Rolf; Harrison, Kenneth; Santanello, Joseph

    2010-01-01

    Recent advances in remote sensing technologies have enabled the monitoring and measurement of the Earth's land surface at an unprecedented scale and frequency. The myriad of these land surface observations must be integrated with the state-of-the-art land surface model forecasts using data assimilation to generate spatially and temporally coherent estimates of environmental conditions. These analyses are of critical importance to real-world applications such as agricultural production, water resources management and flood, drought, weather and climate prediction. This need motivated the development of NASA Land Information System (LIS), which is an expert system encapsulating a suite of modeling, computational and data assimilation tools required to address challenging hydrological problems. LIS integrates the use of several community land surface models, use of ground and satellite based observations, data assimilation and uncertainty estimation techniques and high performance computing and data management tools to enable the assessment and prediction of hydrologic conditions at various spatial and temporal scales of interest. This presentation will focus on describing the results, challenges and lessons learned from the use of remote sensing data for improving land surface modeling, within LIS. More specifically, studies related to the improved estimation of soil moisture, snow and land surface temperature conditions through data assimilation will be discussed. The presentation will also address the characterization of uncertainty in the modeling process through Bayesian remote sensing and computational methods.

  20. [INVITED] Recent advances in surface plasmon resonance based fiber optic chemical and biosensors utilizing bulk and nanostructures

    Science.gov (United States)

    Gupta, Banshi D.; Kant, Ravi

    2018-05-01

    Surface plasmon resonance has established itself as an immensely acclaimed and influential optical sensing tool with quintessential applications in life sciences, environmental monitoring, clinical diagnostics, pharmaceutical developments and ensuring food safety. The implementation of sensing principle of surface plasmon resonance employing an optical fiber as a substrate has concomitantly resulted in the evolution of fiber optic surface plasmon resonance as an exceptionally lucrative scaffold for chemical and biosensing applications. This perspective article outlines the contemporary studies on fiber optic sensors founded on the sensing architecture of propagating as well as localized surface plasmon resonance. An in-depth review of the prevalent analytical and surface chemical tactics involved in configuring the sensing layer over an optical fiber for the detection of various chemical and biological entities is presented. The involvement of nanomaterials as a strategic approach to enhance the sensor sensitivity is furnished concurrently providing an insight into the diverse geometrical blueprints for designing fiber optic sensing probes. Representative examples from the literature are discussed to appreciate the latest advancements in this potentially valuable research avenue. The article concludes by identifying some of the key challenges and exploring the opportunities for expanding the scope and impact of surface plasmon resonance based fiber optic sensors.

  1. The utility of polyester and cotton as swabbing substrates for the removal of cellular material from surfaces.

    Science.gov (United States)

    Mulligan, Christina M; Kaufman, Stacie R; Quarino, Lawrence

    2011-03-01

    Various types of cotton and polyester fabrics were tested to ascertain the optimal physical and chemical characteristics of fabrics needed for the removal of cellular material from surfaces. DNA quantitation values obtained on dried saliva stains showed no difference between cotton and polyester across all constructions and solvent conditions. Fabrics used dry and with water yielded higher quantitation values than those used with isopropanol. Quantitation values were also higher for wovens and nonwovens than knits across all solvent conditions. Low thread count fabrics used with water yielded higher quantitation values, but no correlation between thread count and quantitation values was observed with dry fabrics. A low thread count woven fabric, however, outperformed other tested fabrics when swabbing object surfaces in a highly used room. Full DNA profiles from fingerprints on glass surfaces were obtained with low thread count woven and nonwoven fabrics but not with the knit fabric tested. © 2011 American Academy of Forensic Sciences.

  2. Vegetation composition and 226Ra uptake by native plant species at a uranium mill tailings impoundment in South China

    International Nuclear Information System (INIS)

    Hu, Nan; Ding, Dexin; Li, Guangyue; Zheng, Jifang; Li, Le; Zhao, Weichao; Wang, Yongdong

    2014-01-01

    A field investigation was conducted for the vegetation composition and 226 Ra uptake by native plant species at a uranium mill tailings impoundment in South China. 80 species belonging to 67 genera in 32 families were recorded in the sampling sites. The Poaceae and Asteraceae were the dominant families colonizing the impoundment. The number of the plant species and vegetation community composition in the sampling sites seemed most closely related to the activities of 226 Ra and the pH value of the uranium tailings. The plant species in the sampling sites with relatively low activities of 226 Ra and relatively high pH value formed a relatively stable vegetation community. The plant species in the sampling sites with medium activities of 226 Ra and medium pH value formed the transitional vegetation community. The plant species in the sampling sites with relatively high activities of 226 Ra and relatively low pH value formed a simple unstable vegetation community that was similar to that on the unused grassland. The activities of 226 Ra and transfer factors (TFs) varied greatly with the plant species. The high activities of 226 Ra and TFs were found in the leaves of Pteris multifida (150.6 Bq/g of AW; 9.131), Pteridium aquilinum (122.2 Bq/g of AW; 7.409), and Dryopteris scottii (105.7 Bq/g of AW; 6.408). They satisfied the criteria for a hyperaccumulator for 226 Ra. They may be the candidates for phytoremediation of 226 Ra in the uranium mill tailings impoundment areas and the contaminated soils around. - Highlights: • Vegetation composition of native plant species at an impoundment was analyzed. • 226 Ra uptake by native plant species at the impoundment was investigated. • Poaceae and Asteraceae were the dominated families colonizing this impoundment. • The plant species and composition were related to activities of 226 Ra and pH. • Three plant species were found to be hyperaccumulators for 226 Ra

  3. Utilization of surface active sites on gold in preparation of highly reactive interfaces for alcohols electrooxidation in alkaline media

    International Nuclear Information System (INIS)

    Cherevko, Serhiy; Kulyk, Nadiia; Chung, Chan-Hwa

    2012-01-01

    Graphical abstract: - Abstract: Pt/Au and Pd/Au surface interfaces show very high activity in electrocatalytic oxidation of alcohols in alkaline media. In this work, we present a method for preparation of such structures, which is based on galvanic displacement of the more noble gold with the less noble elements, and investigate their electrocatalytic properties. We propose that active states atoms on the surface of gold may be replaced with Pt and Pd. The generation of active sites on gold is achieved by cathodization in acidic solution. We show that depending on the cathodization time (active sites amount) gold surface electrochemistry changes from that resembling Au to the one typical for pure Pt. The Pt/Au structures prepared with a trace amount of platinum show extremely high electrocatalytic activity. The peak current of methanol oxidation on the Pt/Au electrode is more than an order of magnitude higher than that of the platinum film electrode and more than two orders of magnitude higher than that on the gold unactivated electrode. The difference in the peak current of ethanol oxidation between the Pt/Au and Pt electrodes is ca. 25 times. Moreover, similar deposition of Pt and Pd on active sites on high surface area gold prepared by hydrogen evolution assisted deposition and improved electrocatalytic properties of such structures toward alcohols oxidation is shown.

  4. Utilizing various data sources for surface transportation human factors research : workshop summary report, November 6-7, 2013

    Science.gov (United States)

    2014-07-01

    The report summarizes a 2-day workshop held on November 6-7, 2013, to discuss data sources for surface transportation human factors research. The workshop was designed to assess the increasing number of different datasets and multiple ways of collect...

  5. Utilizing the effective xanthophyll cycle for blooming of Ochromonas smithii and O. itoi (Chrysophyceae on the snow surface.

    Directory of Open Access Journals (Sweden)

    Yukiko Tanabe

    Full Text Available Snow algae inhabit unique environments such as alpine and high latitudes, and can grow and bloom with visualizing on snow or glacier during spring-summer. The chrysophytes Ochromonas smithii and Ochromonas itoi are dominant in yellow-colored snow patches in mountainous heavy snow areas from late May to early June. It is considered to be effective utilizing the xanthophyll cycle and holding sunscreen pigments as protective system for snow algae blooming in the vulnerable environment such as low temperature and nutrients, and strong light, however the study on the photoprotection of chrysophytes snow algae has not been shown. To dissolve how the chrysophytes snow algae can grow and bloom under such an extreme environment, we studied with the object of light which is one point of significance to this problem. We collected the yellow snows and measured photosynthetically active radiation at Mt. Gassan in May 2008 when the bloom occurred, then tried to establish unialgal cultures of O. smithii and O. itoi, and examined their photosynthetic properties by a PAM chlorophyll fluorometer and analyzed the pigment compositions before and after illumination with high-light intensities to investigate the working xanthophyll cycle. This experimental study using unialgal cultures revealed that both O. smithii and O. itoi utilize only the efficient violaxanthin cycle for photoprotection as a dissipation system of surplus energy under prolonged high-light stress, although they possess chlorophyll c with diadinoxanthin.

  6. Utilization of the UV laser with picosecond pulses for the formation of surface microstructures on elastomeric plastics

    Science.gov (United States)

    Antoszewski, B.; Tofil, S.; Scendo, M.; Tarelnik, W.

    2017-08-01

    Elastomeric plastics belong to a wide range of polymeric materials with special properties. They are used as construction material for seals and other components in many branches of industry and, in particular, in the biomedical industry, mechatronics, electronics and chemical equipment. The micromachining of surfaces of these materials can be used to build micro-flow, insulating, dispensing systems and chemical and biological reactors. The paper presents results of research on the effects of micro-machining of selected elastomeric plastics using a UV laser emitting picosecond pulses. The authors see the prospective application of the developed technology in the sealing technique in particular to shaping the sealing pieces co-operating with the surface of the element. The result of the study is meant to show parameters of the UV laser’s performance when producing typical components such as grooves, recesses for optimum ablation in terms of quality and productivity.

  7. Measurement of glucose utilization by Pseudomonas fluorescens that are free-living and that are attached to surfaces

    International Nuclear Information System (INIS)

    Fletcher, M.

    1986-01-01

    The assimilation and respiration of glucose by attached and free-living Pseudomonas fluorescens were compared. The attachment surfaces were polyvinylidene fluoride, polyethylene, and glass. Specific uptake of [ 1 C]glucose was determined after bacterial biomass was measured by (1) microscopic counts or (2) prelabelling of cells by providing [ 3 H]leucine as substrate, followed by dual-labelling scintillation counting. The glucose concentration was 1.4, 3.5, 5.5, 7.6, or 9.7 μM. Glucose assimilation by cells which became detached from the surfaces during incubation with glucose was also measured after the detached cells were collected by filtration. The composition of the substratum had no effect on the amount of glucose assimilated by attached cells. Glucose assimilation by attached cells exceeded that by free-living cells by a factor of between 2 and 5 or more, and respiration of glucose by surface-associated cells was greater than that by free-living bacteria. Glucose assimilation by detached cells was greater than that by attached bacteria. Measurements of biomass by microscopic counts gave more consistent results than those obtained with dual-labelling, but in general, results obtained by both methods were corroborative

  8. Assessment of slipping resistance of footwear and floor surfaces. Influence of manufacture and utilization of the products.

    Science.gov (United States)

    Leclercq, S; Tisserand, M; Saulnier, H

    1995-02-01

    The slipping resistance of footwear or floor surfaces is a characteristic which it is vital to be able to quantify. Work is being carried out at the International Standard Organization (ISO) and at the European Committee for Standardization (CEN) into the slip resistance of both work shoes and protective footwear, involving analysis of the latest developments in both the validity of measuring methods and the extent of the influence of certain experimental parameters on the slip resistance. Two industrial factors, independent of the measuring process but essential to the determination of the coefficient of friction of the models have been experimentally studied, namely the effect of the manufacture of the footwear or floor surfaces on the scattering of the specific coefficient of friction of a referenced model and the effect on the coefficient of friction of mechanical wear and tear on the soles as a result of their use respectively. Work into slipping on industrial floor surfaces is less advanced. Yet, problems raised call for the same approach than for problems linked to slipping resistance of footwear, and applications will be also at first related to standardized measurement conditions.

  9. Low-level radioactive waste disposal in the USA - Use of mill tailings impoundments as a new policy option

    International Nuclear Information System (INIS)

    Farrell, C.W.

    2006-01-01

    Disposal of low-level radioactive waste (LLW) in the United States is facing severe and immediate capacity limitations. Seemingly intractable regulatory and jurisdictional conflicts make establishment of new LLW disposal sites effectively impossible. Uranium mill tailings impoundments constructed at conventional uranium open-cast and underground mines could offer approximately 40 to 80+ million tons of disposal capacity for low activity radioactive waste. Such impoundments would provide an enhanced, high level of environmental and health and safety protection for the direct disposal of depleted uranium, special nuclear material, technologically-enhanced, naturally-occurring radioactive material (TENORM) and mixed waste. Many waste streams, such as TENORM and decommissioning rubble, will be high-volume, low activity materials and ideally suited for disposal in such structures. Materials in a given decay chain with a total activity from all radionuclides present of ∼820 Bq/g (2.22 x 10 -08 Ci/g) with no single radionuclide present in an activity greater than ∼104 Bq/g (2,800 pCi/g) should be acceptable for disposal. Materials of this type could be accepted without any site-specific dose modelling, so long as the total activity of the tailings impoundment not exceed its design capacity (generally 82 x 10 07 Bq/metric tonne) (0.020 Ci/short ton) and the cover design requirements to limit radon releases are satisfied. This paper provides background on US LLW disposal regulations, examines LLW disposal options under active consideration by the US Environmental Protection Agency and Department of Energy, develops generic waste acceptance criteria and identifies policy needs for federal and state governments to facilitate use of uranium mill tailings impoundments for LLW disposal. (author)

  10. Hypersalinity reduces the risk of cyanide toxicosis to insectivorous bats interacting with wastewater impoundments at gold mines.

    Science.gov (United States)

    Griffiths, Stephen R; Donato, David B; Lumsden, Linda F; Coulson, Graeme

    2014-01-01

    Wildlife and livestock that ingest bioavailable cyanide compounds in gold mining tailings dams are known to experience cyanide toxicosis. Elevated levels of salinity in open impoundments have been shown to prevent wildlife cyanide toxicosis by reducing drinking and foraging. This finding appears to be consistent for diurnal wildlife interacting with open impoundments, however the risks to nocturnal wildlife of cyanide exposure are unknown. We investigated the activity of insectivorous bats in the airspace above both fresh (potable to wildlife) and saline water bodies at two gold mines in the goldfields of Western Australian. During this study, cyanide-bearing solutions stored in open impoundments at both mine sites were hypersaline (range=57,000-295,000 mg/L total dissolved solids (TDS)), well above known physiological tolerance of any terrestrial vertebrate. Bats used the airspace above each water body monitored, but were more active at fresh than saline water bodies. In addition, considerably more terminal echolocation buzz calls were recorded in the airspace above fresh than saline water bodies at both mine sites. However, it was not possible to determine whether these buzz calls corresponded to foraging or drinking bouts. No drinking bouts were observed in 33 h of thermal video footage recorded at one hypersaline tailings dam, suggesting that this water is not used for drinking. There is no information on salinity tolerances of bats, but it could be assumed that bats would not tolerate salinity in drinking water at concentrations greater than those documented as toxic for saline-adapted terrestrial wildlife. Therefore, when managing wastewater impoundments at gold mines to avoid wildlife mortalities, adopting a precautionary principle, bats are unlikely to drink solutions at salinity levels ≥50,000 mg/L TDS. © 2013 Published by Elsevier Inc.

  11. Evaluation of behaviors of earth and rockfill dams during construction and initial impounding using instrumentation data and numerical modeling

    Directory of Open Access Journals (Sweden)

    Mohammad Rashidi

    2017-08-01

    Full Text Available In this study, the behavior of Gavoshan dam was evaluated during construction and the first impounding. A two-dimensional (2D numerical analysis was conducted based on a finite difference method on the largest cross-section of the dam using the results of instrument measurements and back analysis. These evaluations will be completed in the case that back analysis is carried out in order to control the degree of the accuracy and the level of confidence of the measured behavior since each of the measurements could be controlled by comparing it to the result obtained from the numerical model. Following that, by comparing the results of the numerical analysis with the measured values, it is indicated that there is a proper consistency between these two values. Moreover, it was observed that the dam performance was suitable regarding the induced pore water pressure, the pore water pressure ratio ru, settlement, induced stresses, arching degree, and hydraulic fracturing probability during the construction and initial impounding periods. The results demonstrated that the maximum settlement of the core was 238 cm at the end of construction. In the following 6 years after construction (initial impounding and exploitation period, the accumulative settlement of the dam was 270 cm. It is clear that 88% of the total settlement of the dam took place during dam construction. The reason is that the clay core was smashed in the wet side, i.e. the optimum moisture content. Whereas the average curving ratio was 0.64 during dam construction; at the end of the initial impounding, the maximum amount of curving ratio in the upstream was 0.81, and the minimum (critical amount in the downstream was 0.52. It was also concluded that this dam is safe in comparison with the behaviors of other similar dams in the world.

  12. Utilization of satellite-derived estimates of meteorological and land surface characteristics in the Land Surface Model for vast agricultural region territory

    Science.gov (United States)

    Muzylev, Eugene; Startseva, Zoya; Uspensky, Alexander; Volkova, Elena

    2015-04-01

    The method has been elaborated to evaluate the water and heat regime characteristics of the territory on a regional scale for the vegetation season based on a physical-mathematical model of water and heat exchange between vegetation covered land surface and atmosphere (LSM, Land Surface Model) appropriate for using satellite information on land surface and meteorological conditions. The developed model is intended for calculating soil water content, evapotranspiration (evaporation from bare soil and transpiration by vegetation), vertical water and heat fluxes as well as land surface and vegetation cover temperatures and vertical distributions of temperature and moisture in the active soil layer. Parameters of the model are soil and vegetation characteristics and input variables are meteorological characteristics. Their values have been obtained from ground-based observations at agricultural meteorological stations and satellite-based measurements by scanning radiometers AVHRR/NOAA, MODIS/EOS Terra and Aqua and SEVIRI (geostationary satellites Meteosat-9, -10). The AVHRR data have been used to build the estimates of three types of land surface temperature (LST): land skin temperature Tsg, air temperature at a level of vegetation cover Ta and efficient radiation temperature Tseff, emissivity E, normalized vegetation index NDVI, vegetation cover fraction B, leaf area index LAI, and precipitation. The set of estimates derived from MODIS data has comprised values of LST Tls, E, NDVI and LAI. The SEVIRI-based retrievals have included Tls, Ta, Е at daylight and nighttime, LAI (daily) and precipitation. The case study has been carried out for agricultural Central Black Earth region of the European Russia of 227,300 sq.km containing 7 regions of the Russian Federation for years 2009-2013 vegetation seasons. Estimates of described characteristics have been built with the help of the developed original and improved pre-existing methods and technologies of thematic processing

  13. Temporal variation and spatial distribution of PAH in water of Three Gorges Reservoir during the complete impoundment period.

    Science.gov (United States)

    Wang, Jingxian; Henkelmann, Bernhard; Bi, Yonghong; Zhu, Kongxian; Pfister, Gerd; Hu, Wei; Temoka, Cedrique; Westrich, Bernhard; Schramm, Karl-Werner

    2013-10-01

    Bioavailable concentrations of polycyclic aromatic hydrocarbons (PAHs) were investigated in water of Three Gorges Reservoir (TGR) using semipermeable membrane devices during the period of completely impounding water. ∑PAH concentrations in water of TGR in the period of completely impounding water were 15-381 ng L(-1). ∑PAH concentrations increased from town or counties to big industrialized cities in TGR, indicating urbanization effects on PAH pollution in the water. Tributaries in TGR have a certain contribution of PAH pollution to the mainstream of Yangtze River and their pollution could not be neglected. An obvious decrease of PAH concentration was observed after 175-m water impounding in 2011 in TGR. Several factors may account for this decrease, including execution of comprehensive treatment and management measures in TGR, less rainfall in 2011, and sedimentation effect caused by the dam. Passive sampling method has been successfully applied in the investigation of trace PAH in water of TGR and proved to be a useful and efficient tool for the management and sustainable development of the big reservoir. The results of the study provide valuable information about PAH pollution in the whole reservoir including some tributaries, and the pollution status is dynamically related with human activities. Therefore, PAH could be used as a marker compound or indicator in the network monitoring system to surveil and trace the pollution status in TGR.

  14. [Effects of Three Gorges Reservoir impoundment on the wetland ecosystem service value of Dongting Lake, South-central China].

    Science.gov (United States)

    Li, Jing-Bao; Dai, Yong; Yin, Ri-Xin; Yang, Yan; Li, Yu-dan; Wang, Ke-ying

    2013-03-01

    Based on the field investigation and measurement, and by using the monetary method, this paper estimated the wetland ecosystem service value of Dongting Lake before and after the impoundment of Three Gorges Reservoir (in 1996 and 2010, respectively). After the impoundment, the total ecosystem service value increased from 156.69x10(8) yuan in 1996 to 177.11x10(8) yuan in 2010. The main services value in 1996 was in the order of flood storage and regulation > water storage and supply > air regulation > scientific research and education, while that in 2010 was leisure tourism > shipping transportation > air regulation > water storage and supply. In the total service value of the wetland ecosystem, the direct value associated with water decreased from 110. 85x10(8) in 1996 to 27.47x10(8) in 2010, with a decrement of 75.2%. Though the proportion of the direct value in the production and supply of material products had somewhat increase, the indirect value in ecological environment regulation and maintenance and in culture and society still maintained at about 80% of the total value. In addition to climate factors, the impoundment of Three Gorges Reservoir and the reduction of water and sediment from Yangtze River to the Lake were the crucial reasons leading to the changes of the wetland ecosystem service value of Dongting Lake.

  15. Evaluation of factors related to increased zooplankton biomass and altered species composition following impoundment of a Newfoundland reservoir

    International Nuclear Information System (INIS)

    Campbell, C.E.; Knoechel, R.; Copeman, D.

    1998-01-01

    An 11-year study of the zooplankton community in Cat Arm Hydroelectric Reservoir in Newfoundland was conducted to assess long-term zooplankton community dynamics in a subarctic system. Zooplankton biomass and species compositions were monitored from 1983 to 1993. The monitoring program documented the trophic evolution of the Cat Arm system as it changed from a shallow lake with short water retention time to a deep reservoir with a much lower flushing rate. Zooplankton biomass increased approximately 19-fold in the oligotrophic hydroelectric reservoir following impoundment in 1984, relative to biomass in the preexisting lake. During the first three years of impoundment, there were no increases in either phytoplankton biomass or primary productivity. Natality of the dominant cladoceran (Daphnia catawba) did not increase. Summer water retention time increased from pre-impoundment levels of 4 days in 1983 to 338 days in 1993. The study showed that zooplankton biomass was greatly correlated with water retention time, and showed no major correlation with phytoplankton biomass, primary productivity, nutrient concentrations, pH, colour, or epilimnetic temperature. It was concluded that changes in the zooplankton community in the hydroelectric reservoir were a result of decreases in losses due to washout. 41 refs., 2 tabs., 6 figs

  16. Utilizing CLASIC observations and multiscale models to study the impact of improved Land surface representation on modeling cloud- convection

    Energy Technology Data Exchange (ETDEWEB)

    Niyogi, Devdutta S. [Purdue

    2013-06-07

    The CLASIC experiment was conducted over the US southern great plains (SGP) in June 2007 with an objective to lead an enhanced understanding of the cumulus convection particularly as it relates to land surface conditions. This project was design to help assist with understanding the overall improvement of land atmosphere convection initiation representation of which is important for global and regional models. The study helped address one of the critical documented deficiency in the models central to the ARM objectives for cumulus convection initiation and particularly under summer time conditions. This project was guided by the scientific question building on the CLASIC theme questions: What is the effect of improved land surface representation on the ability of coupled models to simulate cumulus and convection initiation? The focus was on the US Southern Great Plains region. Since the CLASIC period was anomalously wet the strategy has been to use other periods and domains to develop the comparative assessment for the CLASIC data period, and to understand the mechanisms of the anomalous wet conditions on the tropical systems and convection over land. The data periods include the IHOP 2002 field experiment that was over roughly same domain as the CLASIC in the SGP, and some of the DOE funded Ameriflux datasets.

  17. Layout designs of surface barrier coatings for boosting the capability of oxygen/vapor obstruction utilized in flexible electronics

    Science.gov (United States)

    Lee, Chang-Chun; Huang, Pei-Chen; He, Jing-Yan

    2018-04-01

    Organic light-emitting diode-based flexible and rollable displays have become a promising candidate for next-generation flexible electronics. For this reason, the design of surface multi-layered barriers should be optimized to enhance the long-term mechanical reliability of a flexible encapsulation that prevents the penetration of oxygen and vapor. In this study, finite element-based stress simulation was proposed to estimate the mechanical reliability of gas/vapor barrier design with low-k/silicon nitride (low-k/SiNx) stacking architecture. Consequently, stress-induced failure of critical thin films within the flexible display under various bending conditions must be considered. The feasibility of one pair SiO2/SiNx barrier design, which overcomes the complex lamination process, and the critical bending radius, which is decreased to 1.22 mm, were also examined. In addition, the influence of distance between neutral axes to the concerned layer surface dominated the induced-stress magnitude rather than the stress compliant mechanism provided from stacked low-k films.

  18. 100-kWe Lunar/Mars surface power utilizing the SP-100 reactor with dynamic conversion

    International Nuclear Information System (INIS)

    Harty, R.B.; Mason, L.S.

    1993-01-01

    An integration study was performed coupling an SP-100 reactor with either a Brayton or Stirling power conversion subsystem. A power level of 100 kWe was selected for the study. The power system was to be compatible with both the lunar and Mars surface environment and require no site preparation. In addition, the reactor was to have integral shielding and be completely self-contained, including its own auxiliary power for start-up. Initial reliability studies were performed to determine power conversion redundancy and engine module size. Previous studies were used to select the power conversion optimum operating conditions (ratio of hot-side temperature to cold-side temperature). Results of the study indicated that either the Brayton or Stirling power conversion subsystems could be integrated with the SP-100 reactor for either a lunar or Mars surface power application. For the lunar environment, the reactor and primary coolant loop would be contained in a guard vessel to protect from a loss of primary loop containment. For the Mars environment, all refractory components including the reactor, primary coolant, and power conversion components would be contained in a vacuum vessel for protection against the CO 2 environment. The vacuum would be maintained by an active ion pumping system. These active ion vacuum systems have no moving parts and have a long history of reliable operation

  19. Methane oxidation and molecular characterization of methanotrophs from a former mercury mine impoundment

    Science.gov (United States)

    Baesman, Shaun; Miller, Laurence G.; Wei, Jeremy H.; Cho, Yirang; Matys, Emily D.; Summons, Roger E.; Welander, Paula V.; Oremland, Ronald S.

    2015-01-01

    The Herman Pit, once a mercury mine, is an impoundment located in an active geothermal area. Its acidic waters are permeated by hundreds of gas seeps. One seep was sampled and found to be composed of mostly CO2 with some CH4 present. The δ13CH4 value suggested a complex origin for the methane: i.e., a thermogenic component plus a biological methanogenic portion. The relatively 12C-enriched CO2 suggested a reworking of the ebullitive methane by methanotrophic bacteria. Therefore, we tested bottom sediments for their ability to consume methane by conducting aerobic incubations of slurried materials. Methane was removed from the headspace of live slurries, and subsequent additions of methane resulted in faster removal rates. This activity could be transferred to an artificial, acidic medium, indicating the presence of acidophilic or acid-tolerant methanotrophs, the latter reinforced by the observation of maximum activity at pH = 4.5 with incubated slurries. A successful extraction of sterol and hopanoid lipids characteristic of methanotrophs was achieved, and their abundances greatly increased with increased sediment methane consumption. DNA extracted from methane-oxidizing enrichment cultures was amplified and sequenced for pmoA genes that aligned with methanotrophic members of the Gammaproteobacteria. An enrichment culture was established that grew in an acidic (pH 4.5) medium via methane oxidation.

  20. Effect of fishing effort on catch rate and catchability of largemouth bass in small impoundments

    Science.gov (United States)

    Wegener, M. G.; Schramm, Harold; Neal, J. W.; Gerard, P.D.

    2018-01-01

    Largemouth bass Micropterus salmoides (Lacepède) catch rates decline with sustained fishing effort, even without harvest. It is unclear why declines in catch rate occur, and little research has been directed at how to improve catch rate. Learning has been proposed as a reason for declining catch rate, but has never been tested on largemouth bass. If catch rate declines because fish learn to avoid lures, periods of no fishing could be a management tool for increasing catch rate. In this study, six small impoundments with established fish populations were fished for two May to October fishing seasons to evaluate the effect of fishing effort on catch rate. Closed seasons were implemented to test whether a 2‐month period of no fishing improved catch rates and to determine whether conditioning from factors other than being captured reduced catch rate. Mixed‐model analysis indicated catch rate and catchability declined throughout the fishing season. Catch rate and catchability increased after a 2‐month closure but soon declined to the lowest levels of the fishing season. These changes in catch rate and catchability support the conclusion of learned angler avoidance, but sustained catchability of fish not previously caught does not support that associative or social learning affected catchability.

  1. Survivability of ancient man-made earthen mounds: implications for uranium mill tailings impoundments

    Energy Technology Data Exchange (ETDEWEB)

    Lindsey, C.G.; Mishima, J.; King, S.E.; Walters, W.H.

    1983-06-01

    As part of a study for the Nuclear Regulatory Commission (NRC), the Pacific Northwest Laboratory (PNL) is investigating long-term stabilization techniques for uranium mill impoundments. Part of this investigation involves the design of a rock armoring blanket (riprap) to mitigate wind and water erosion of the underlying soil cover, which in turn prevents exposure of the tailings to the environment. However, the need for the armoring blanket, as well as the blanket's effectiveness, depends on the stability of the underlying soil cap (radon suppression cover) and on the tailings themselves. Compelling evidence in archaeological records suggests that large man-made earthen structures can remain sound and intact for time periods comparable to those required for the stabilization of the tailings piles if properly constructed. We present archaeological evidence on the existence and survivability of man-made earthen and rock structures through specific examples of such structures from around the world. We also review factors contributing to their survival or destruction and address the influence of climate, building materials, and construction techniques on survivability.

  2. Survivability of ancient man-made earthen mounds: implications for uranium mill tailings impoundments

    International Nuclear Information System (INIS)

    Lindsey, C.G.; Mishima, J.; King, S.E.; Walters, W.H.

    1983-06-01

    As part of a study for the Nuclear Regulatory Commission (NRC), the Pacific Northwest Laboratory (PNL) is investigating long-term stabilization techniques for uranium mill impoundments. Part of this investigation involves the design of a rock armoring blanket (riprap) to mitigate wind and water erosion of the underlying soil cover, which in turn prevents exposure of the tailings to the environment. However, the need for the armoring blanket, as well as the blanket's effectiveness, depends on the stability of the underlying soil cap (radon suppression cover) and on the tailings themselves. Compelling evidence in archaeological records suggests that large man-made earthen structures can remain sound and intact for time periods comparable to those required for the stabilization of the tailings piles if properly constructed. We present archaeological evidence on the existence and survivability of man-made earthen and rock structures through specific examples of such structures from around the world. We also review factors contributing to their survival or destruction and address the influence of climate, building materials, and construction techniques on survivability

  3. The Effect of Zebra Mussels on Algal Community Structure in an Impounded River System

    Science.gov (United States)

    Trumble, A. F.; Luttenton, M.

    2005-05-01

    The zebra mussel, Dreissena polymorpha, invaded the Great Lakes Region in the mid 1980's, and subsequently colonized inland lakes and coastal river systems through secondary invasions. The Muskegon River below Croton Dam was colonized by zebra mussels in 2000 following their introduction into Croton impoundment in the late 1990's. No zebra mussels were found below Croton Dam in 1999 but had increased to 25,000 m-2 by 2001. We examined the affect of zebra mussels on epilithic periphyton communities by comparing plots that were and were not colonized by zebra mussels. Chlorophyll a increased in both treatments over time but was significantly higher in control plots than in zebra mussel plots. The concentration of chlorophyll a in the control plots increased from 14 µgcm-2 to 26 µgcm-2 and the concentration in the zebra mussel plots started at 12 µgcm-2, peaked at 19 µgcm-2, and then decreased to 15 µgcm-2 over a 6 week period. In a related experiment using artificial streams, chlorophyll a increased with increasing zebra mussel density, but differences were not significant. The different trends observed between the two experiments may be explained in part by arthropod invertebrates associated with zebra mussel populations.

  4. Impounded Marshes on Subsided Islands: Simulated Vertical Accretion, Processes, and Effects, Sacramento-San Joaquin Delta, CA USA

    Directory of Open Access Journals (Sweden)

    Steven J. Deverel

    2014-06-01

    Full Text Available There is substantial interest in stopping and reversing the effects of subsidence in the Sacramento–San Joaquin Delta (Delta where organic soils predominate. Also, the passage of California Assembly Bill 32 in 2006 created the potential to trade credits for carbon sequestered in wetlands on subsided Delta islands. The primary purpose of the work described here was to estimate future vertical accretion and understand processes that affect vertical accretion and carbon sequestration in impounded marshes on subsided Delta islands. Using a cohort-accounting model, we simulated vertical accretion from 4,700 calibrated years before present (BP at a wetland area located within Franks Tract State Recreation Area (lat 38.059, long −121.611, hereafter, “Franks Wetland”—a small, relatively undisturbed marsh island—and at the Twitchell Island subsidence-reversal demonstration project since 1997. We used physical and chemical data collected during the study as well as literature values for model inputs. Model results compared favorably with measured rates of vertical accretion, mass of carbon sequestered, bulk density and organic matter content. From 4,700 to model-estimated 350 years BP, the simulated rate of vertical accretion at Franks Wetland averaged about 0.12 cm yr-1, which is within the range of rates in tidal wetlands worldwide. Our model results indicate that large sediment inputs during the last 150 to 200 years resulted in a higher accretion rate of 0.3 cm yr -1. On Twitchell Island, greater organic inputs resulted in average vertical accretion rates as high as 9.2 cm yr -1. Future simulations indicate that the managed impounded marsh will accrete highly organic material at rates of about 3 cm yr -1. Model results coupled with GIS analysis indicate that large areas of the periphery of the Delta, if impounded and converted to freshwater marsh, could be restored to tidal elevations within 50 to 100 years. Most of the

  5. Utilization of specific and non-specific peptide interactions with inorganic nanomaterials on the surface of bacteriophage M13: Methodologies towards phage supported bi-functional materials

    Science.gov (United States)

    Avery, Kendra Nicole

    Many types of organisms create a variety of nano and micro scale materials from precursors available in their surrounding environments by a process called biomineralization. As scientists begin to understand how these organisms utilize specific and non-specific interactions with a variety of biopolymers such as chitin, peptides, proteins and nucleic acids with these precursors to create inorganic/organic composite materials, they have begun to wonder about the synthesis of other types of non-biologically templated synthetic techniques that might be possible. Bioengineered organisms and biopolymers have begun to be used for these types of studies. A variety of selection techniques exist for discovering biopolymers with an affinity for a target material, however, one of the most notable is a technique called peptide phage display. This is a technique that utilizes a commercially available randomized peptide library attached at the tip of the filamentous bacteriophage M13. In this dissertation capabilities of bacteriophage M13 are explored in regard to the creation of bi-functional nano materials by exploiting both specific peptide interactions as well as non-specific peptide interactions on the surface of the organism. Chapter 2 focuses on utilizing the specific peptide interactions of the randomized library at pIII in order to discover peptides with high binding affinity for a variety of nanomaterials. Selection studies called biopanning are performed on a variety of nanomaterials such as CaMoO4, allotropes of Ni, Fe2O3 and Fe3O4, and Rh and Pt with the fcc type crystal structure. Similarities and differences between peptides discovered for these materials are discussed. Chapter 3 focuses on utilizing the non-specific peptide interactions on the long axis of M13 called pVIII. The pVIII region consists of 2700 copies of the same 50 amino acid protein which as a negatively charged domain which is exposed to solution. The pVIII region therefore provides the surface of

  6. The utilization of surface free-energy parameters for the selection of a suitable binder in fluidized bed granulation.

    Science.gov (United States)

    Planinsek, O; Pisek, R; Trojak, A; Srcic, S

    2000-10-10

    Surface free energy was determined for model substances pentoxyfilline, acyclovir, lactose and binding agents (that were used in the granulation process) hydroxypropilmethyl cellulose (HPMC) and polyvinylpyrrolidone (PVP) were determined by contact angle measurements. The methods of Wu, Good-van Oss and Della Volpe were used for solid-surface free-energy calculation. Spreading coefficients (S) were calculated and correlated with granulate properties. Granulates consisted of model drug and binding agent, and were produced in fluid bed granulator Glatt powder coater granulator GPCG1 by means of spraying the colloidal solution of binder on the model substance. Granules contained either 5% or 10% binder. Inverse granules, however, were also produced by spraying the model drug (i.e. pentoxyfilline and lactose) on the binding agent (HPMC, PVP). Particle size distribution, friability, true density, bulk density and tapped density of the granulates were determined. Although many different parameters influence the granule properties, it has been found that the interactions between the drug and the binder play a very important role. Spreading coefficients were found to be in good correlation with the friability of granulates. Positive spreading coefficient values of the binder over the model substance correlate well with the low friability of the granules containing lower amount of binder, i.e. 5%. In the group of the same binder, the spreading coefficient values decrease from pentoxyfilline over lactose to acyclovir. Friability results show that, for the system under consideration, PVP offers certain advantages over the grade of HPMC employed. The increase of the binder amount from 5 to 10% resulted in more friable granulates. Lower work of cohesion of the binder (PVP and HPMC) than the work of adhesion between binder and the model substances is considered responsible for the higher friability of the granules. The inverse granulation process, where the suspension of the

  7. Improving groundwater predictions utilizing seasonal precipitation forecasts from general circulation models forced with sea surface temperature forecasts

    Science.gov (United States)

    Almanaseer, Naser; Sankarasubramanian, A.; Bales, Jerad

    2014-01-01

    Recent studies have found a significant association between climatic variability and basin hydroclimatology, particularly groundwater levels, over the southeast United States. The research reported in this paper evaluates the potential in developing 6-month-ahead groundwater-level forecasts based on the precipitation forecasts from ECHAM 4.5 General Circulation Model Forced with Sea Surface Temperature forecasts. Ten groundwater wells and nine streamgauges from the USGS Groundwater Climate Response Network and Hydro-Climatic Data Network were selected to represent groundwater and surface water flows, respectively, having minimal anthropogenic influences within the Flint River Basin in Georgia, United States. The writers employ two low-dimensional models [principle component regression (PCR) and canonical correlation analysis (CCA)] for predicting groundwater and streamflow at both seasonal and monthly timescales. Three modeling schemes are considered at the beginning of January to predict winter (January, February, and March) and spring (April, May, and June) streamflow and groundwater for the selected sites within the Flint River Basin. The first scheme (model 1) is a null model and is developed using PCR for every streamflow and groundwater site using previous 3-month observations (October, November, and December) available at that particular site as predictors. Modeling schemes 2 and 3 are developed using PCR and CCA, respectively, to evaluate the role of precipitation forecasts in improving monthly and seasonal groundwater predictions. Modeling scheme 3, which employs a CCA approach, is developed for each site by considering observed groundwater levels from nearby sites as predictands. The performance of these three schemes is evaluated using two metrics (correlation coefficient and relative RMS error) by developing groundwater-level forecasts based on leave-five-out cross-validation. Results from the research reported in this paper show that using

  8. Surface layer investigation of duplex stainless steel S32205 after stress peening utilizing X-ray diffraction

    International Nuclear Information System (INIS)

    Feng, Qiang; Jiang, Chuanhai; Xu, Zhou

    2013-01-01

    Highlights: ► The stress shot peening is superior to the conventional shot peening. ► Residual stresses along the loaded direction are bigger than transverse direction. ► Higher prestress leads to smaller domain size, high density of dislocation. ► Compared to ferrite, austenite has much higher hardness and work hardening. ► Ferrite has higher recover of elastic deformation than austenite after unloading. - Abstract: Residual stresses and micro-hardness of duplex stainless steel S32205 after stress peening are measured and domain sizes and microstrain are calculated. The results show that stress peening can significantly improve the compressive residual stresses and micro-hardness in both austenite and ferrite, and the former is affected by both the prestress and the measurement directions. Microstructure investigation reveals that material deformation is enhanced after stress peening, and smaller domain sizes and higher microstrain are introduced. The compressive residual stress enhancement by stress peening in ferrite is more than that in austenite under the same stress peening, which is due to the more elastic deformation recover in ferrite. Therefore, the difference of residual stresses between ferrite and austenite can be narrowed down by conducting appropriate stress peening. Based on these investigations, it is concluded that stress peening is superior to conventional shot peening treatment to improve the surface properties of duplex stainless steel

  9. Efficient biological conversion of carbon monoxide (CO) to carbon dioxide (CO2) and for utilization in bioplastic production by Ralstonia eutropha through the display of an enzyme complex on the cell surface.

    Science.gov (United States)

    Hyeon, Jeong Eun; Kim, Seung Wook; Park, Chulhwan; Han, Sung Ok

    2015-06-25

    An enzyme complex for biological conversion of CO to CO2 was anchored on the cell surface of the CO2-utilizing Ralstonia eutropha and successfully resulted in a 3.3-fold increase in conversion efficiency. These results suggest that this complexed system may be a promising strategy for CO2 utilization as a biological tool for the production of bioplastics.

  10. The Surface Coating of Commercial LiFePO4 by Utilizing ZIF-8 for High Electrochemical Performance Lithium Ion Battery

    Science.gov (United States)

    Xu, XiaoLong; Qi, CongYu; Hao, ZhenDong; Wang, Hao; Jiu, JinTing; Liu, JingBing; Yan, Hui; Suganuma, Katsuaki

    2018-03-01

    The requirement of energy-storage equipment needs to develop the lithium ion battery (LIB) with high electrochemical performance. The surface modification of commercial LiFePO4 (LFP) by utilizing zeolitic imidazolate frameworks-8 (ZIF-8) offers new possibilities for commercial LFP with high electrochemical performances. In this work, the carbonized ZIF-8 (CZIF-8) was coated on the surface of LFP particles by the in situ growth and carbonization of ZIF-8. Transmission electron microscopy indicates that there is an approximate 10 nm coating layer with metal zinc and graphite-like carbon on the surface of LFP/CZIF-8 sample. The N2 adsorption and desorption isotherm suggests that the coating layer has uniform and simple connecting mesopores. As cathode material, LFP/CZIF-8 cathode-active material delivers a discharge specific capacity of 159.3 mAh g-1 at 0.1C and a discharge specific energy of 141.7 mWh g-1 after 200 cycles at 5.0C (the retention rate is approximate 99%). These results are attributed to the synergy improvement of the conductivity, the lithium ion diffusion coefficient, and the degree of freedom for volume change of LFP/CZIF-8 cathode. This work will contribute to the improvement of the cathode materials of commercial LIB.[Figure not available: see fulltext.

  11. A microbial arsenic cycle in sediments of an acidic mine impoundment: Herman Pit, Clear Lake, California

    Science.gov (United States)

    Blum, Jodi S.; McCann, Shelley; Bennett, S.; Miller, Laurence G.; Stolz, J. R.; Stoneburner, B.; Saltikov, C.; Oremland, Ronald S.

    2015-01-01

    The involvement of prokaryotes in the redox reactions of arsenic occurring between its +5 [arsenate; As(V)] and +3 [arsenite; As(III)] oxidation states has been well established. Most research to date has focused upon circum-neutral pH environments (e.g., freshwater or estuarine sediments) or arsenic-rich “extreme” environments like hot springs and soda lakes. In contrast, relatively little work has been conducted in acidic environments. With this in mind we conducted experiments with sediments taken from the Herman Pit, an acid mine drainage impoundment of a former mercury (cinnabar) mine. Due to the large adsorptive capacity of the abundant Fe(III)-rich minerals, we were unable to initially detect in solution either As(V) or As(III) added to the aqueous phase of live sediment slurries or autoclaved controls, although the former consumed added electron donors (i.e., lactate, acetate, hydrogen), while the latter did not. This prompted us to conduct further experiments with diluted slurries using the live materials from the first incubation as inoculum. In these experiments we observed reduction of As(V) to As(III) under anoxic conditions and reduction rates were enhanced by addition of electron donors. We also observed oxidation of As(III) to As(V) in oxic slurries as well as in anoxic slurries amended with nitrate. We noted an acid-tolerant trend for sediment slurries in the cases of As(III) oxidation (aerobic and anaerobic) as well as for anaerobic As(V) reduction. These observations indicate the presence of a viable microbial arsenic redox cycle in the sediments of this extreme environment, a result reinforced by the successful amplification of arsenic functional genes (aioA, and arrA) from these materials.

  12. Destratification of an impounding reservoir using compressed air??case of Mudi reservoir, Blantyre, Malawi

    Science.gov (United States)

    Chipofya, V. H.; Matapa, E. J.

    This paper reviews the operational and cost effectiveness of a compressed air destratification system that was installed in the Mudi reservoir for destratifying the reservoir. Mudi reservoir is a raw water source for the Blantyre Water Board. It has a capacity of 1,400,000 cubic metres. The reservoir is 15.3 m deep at top water level. In the absence of any artificial circulation of air, the reservoir stratifies into two layers. There is a warm epilimnion in the top 3 m of the reservoir, with temperatures ranging from 23 to 26 °C. There is prolific algal growth in this layer. The bottom layer has much lower temperatures, and is oxygen deficient. Under such anaerobic conditions, ammonia, sulphides, iron and manganese are released from the sediments of the reservoir. As a result of nutrient inflow from the catchments, coupled with tropical ambient temperatures, the reservoir is most times infested with blue-green algae. This results into water treatment problems in respect of taste and odour and iron and manganese soluble salts. To abate such problems, air is artificially circulated in the reservoir, near the intake tower, through a perforated pipe that is connected to an electrically driven compressor. This causes artificial circulation of water in the hypolimnion region of the reservoir. As a result of this circulation, a hostile environment that inhibits the propagation of algae is created. Dissolved oxygen and temperature profiles are practically uniform from top to bottom of reservoir. Concentrations of iron and manganese soluble salts are much reduced at any of the draw-off points available for the water treatment process. The paper concludes by highlighting the significant cost savings in water treatment that are accrued from the use of compressed air destratification in impounding water storage reservoirs for the control of algae and other chemical pollutants.

  13. Utilization of Polyaniline (PAni) as Conductive Filler on Poly (Ethylene Oxide) / Poly (Vinyl Chloride) Films: Effects of Naphthalene as Surface Modifier on Electrical Conductivity

    Science.gov (United States)

    Yazid, Mohammed Izzuddeen Bin Mohd; Ghani, Supri A.; Jin, Tan Soo; Fazlina Osman, Azlin; Din, Siti Hajar Mohd

    2017-10-01

    The aim of the study was to utilize polyaniline (PAni) as conductive filler in poly (ethylene oxide) / poly (vinyl chloride) (PEO/PVC) films. Naphthalene was used as surface modifier to increase the properties of PEO/PVC/PAni films. The electrical conductivity of PEO/PVC/PAni film improved with higher loading of PAni until it reached the percolation threshold at 10 wt%. Moreover, the conductivity of the films also improved with the addition of naphthalene compared to the films without naphthalene. These enhancements were due to the improved interfacial bonding between PEO/PVC blend and PAni, which were supported by scanning electron microscopy (SEM) analysis. In addition, no new chemical bonding was created with the incorporation of naphthalene as proved by the FTIR analysis.

  14. Conceptual designs of near surface disposal facility for radioactive waste arising from the facilities using radioisotopes and research facilities for nuclear energy development and utilization

    International Nuclear Information System (INIS)

    Sakai, Akihiro; Yoshimori, Michiro; Okoshi, Minoru; Yamamoto, Tadatoshi; Abe, Masayoshi

    2001-03-01

    Various kinds of radioactive waste is generating from the utilization of radioisotopes in the field of science, technology, etc. and the utilization and development of nuclear energy. In order to promote the utilization of radionuclides and the research activities, it is necessary to treat and dispose of radioactive waste safely and economically. Japan Nuclear Cycle Development Institute (JNC), Japan Radioisotope Association (JRIA) and Japan Atomic Energy Research Institute (JAERI), which are the major waste generators in Japan in these fields, are promoting the technical investigations for treatment and disposal of the radioactive waste co-operately. Conceptual design of disposal facility is necessary to demonstrate the feasibility of waste disposal business and to determine the some conditions such as the area size of the disposal facility. Three institutes share the works to design disposal facility. Based on our research activities and experiences of waste disposal, JAERI implemented the designing of near surface disposal facilities, namely, simple earthen trench and concrete vaults. The designing was performed based on the following three assumed site conditions to cover the future site conditions: (1) Case 1 - Inland area with low groundwater level, (2) Case 2 - Inland area with high groundwater level, (3) Case 3 - Coastal area. The estimation of construction costs and the safety analysis were also performed based on the designing of facilities. The safety assessment results show that the safety for concrete vault type repository is ensured by adding low permeability soil layer, i.e. mixture of soil and bentonite, surrounding the vaults not depending on the site conditions. The safety assessment results for simple earthen trench also show that their safety is ensured not depending on the site conditions, if they are constructed above groundwater levels. The construction costs largely depend on the depth for excavation to build the repositories. (author)

  15. Analysis of Wading Bird use of Impounded Wetland Habitat on the Kennedy Space Center/Merritt Island National Wildlife Refuge, 1987-1998

    Science.gov (United States)

    Stolen, Eric D.; Breininger, David R.; Smith, Rebecca B.; Quincy, Charlie (Technical Monitor)

    2002-01-01

    This report summarizes results of the first eleven years of monthly aerial surveys of wading bird use of foraging habitats within impoundments on the Kennedy Space Center/Merritt Island National Wildlife Refuge. Some impoundments were used much more heavily by wading birds than were others. Analysis suggests that an increase in interspersion of open water and vegetated habitats is preferred foraging habitat. Many wading bird species increased their use of vegetated habitat in Fall and Winter when impoundments were flooded. The mean number of wading birds per survey was greatest during the Pre-nesting and Nesting seasons, declined during Post-nesting season, and was lowest during Winter when water levels within impoundments were high. During these times, shallow habitat along the IRL shoreline provided alternative habitats for wading birds. Various measures of monthly precipitation and impoundment water level were well correlated with the numbers of wading birds observed. Numbers of nesting attempts was steady during the study period, with the exception of an unusually high number of attempts in 1990. White Ibis accounted for over half of all wading bird nests counted. The mean number of nests per colony decreased during the study period, and the number of individual colonies increased.

  16. Sharptooth catfish shows its metal: a case study of metal contamination at two impoundments in the Olifants River, Limpopo river system, South Africa.

    Science.gov (United States)

    Jooste, Antoinette; Marr, Sean M; Addo-Bediako, Abraham; Luus-Powell, Wilmien J

    2015-02-01

    Clarias gariepinus is increasing in importance as a global aquaculture species with a 100 fold increase in production over the past decade but this species still remains one of the most important wild harvested freshwater food fish throughout rural Africa. However, this species has been shown to accumulate metals from contaminated inland waters. In this paper, the metal concentrations in muscle tissue of C. gariepinus from two main-stem impoundments in the Olifants River, Limpopo Basin, were measured and a desktop risk assessment based on the US-EPA methodology completed to evaluate whether long-term consumption of C. gariepinus from these impoundments may pose a health risk to rural communities. Our results show that metals are accumulating in the muscle tissue of C. gariepinus and have appeared to have increased in the last two decades. Risk assessment generated Hazard quotients (HQ) greater than 1 indicate that long term consumption of fish from these impoundments may cause adverse health impacts. We found that lead (HQ=9), antimony (HQ=14), cobalt (HQ=2) and chromium (HQ=1) at one impoundment and lead (HQ=2) at the other impoundment were above acceptable levels for weekly consumption of 150 g C. gariepinus muscle tissue. Copyright © 2014 Elsevier Inc. All rights reserved.

  17. Influences of local habitat, tributary position, and dam characteristics on fish assemblages within impoundments of low-head dams in the tributaries of the Qingyi River, China.

    Science.gov (United States)

    Li, Xian; Li, Yu-Ru; Chu, Ling; Zhu, Ren; Wang, Li-Zhu; Yan, Yun-Zhi

    2016-03-18

    Low-head dam impoundments modify local habitat and alter fish assemblages; however, to our knowledge, the pattern of how fish assemblages in the impoundments relate to local habitat, tributary position, and dam characteristics is still unclear. We used data collected in 62 impoundments created by low-head dams in headwater streams of the Qingyi River, China, to examine relationships between fish assemblages and local habitat, tributary position, and dam characteristics. We also assessed the relative importance of the three groups of factors in determining fish species richness and composition. Linear regression models showed that fish species richness was related to substrate heterogeneity, confluence link, and dam number upstream. Redundancy analysis showed that fish species compositions were influenced by substrate heterogeneity, confluence link, dam height, dam numbers upstream and downstream. Overall, dam characteristics were more important in affecting fish species richness but less important in determining fish species composition than local habitat (i.e., substrate heterogeneity) and tributary position. Our results suggest that low-head dam may affect fish species richness in impoundments by modifying local habitat and constraining fish movement, and the relative abundances of those fish species may depend more on species habitat presences and stream size than on impoundment size and number.

  18. Lactobacillus plantarum gene clusters encoding putative cell-surface protein complexes for carbohydrate utilization are conserved in specific gram-positive bacteria

    Directory of Open Access Journals (Sweden)

    Muscariello Lidia

    2006-05-01

    D proteins form cell-surface protein complexes and play a role in carbon source acquisition. Primary occurrence in plant-associated gram-positive bacteria suggests a possible role in degradation and utilization of plant oligo- or poly-saccharides.

  19. Utility of remote sensing-based surface energy balance models to track water stress in rain-fed switchgrass under dry and wet conditions

    Science.gov (United States)

    Bhattarai, Nishan; Wagle, Pradeep; Gowda, Prasanna H.; Kakani, Vijaya G.

    2017-11-01

    The ability of remote sensing-based surface energy balance (SEB) models to track water stress in rain-fed switchgrass (Panicum virgatum L.) has not been explored yet. In this paper, the theoretical framework of crop water stress index (CWSI; 0 = extremely wet or no water stress condition and 1 = extremely dry or no transpiration) was utilized to estimate CWSI in rain-fed switchgrass using Landsat-derived evapotranspiration (ET) from five remote sensing based single-source SEB models, namely Surface Energy Balance Algorithm for Land (SEBAL), Mapping ET with Internalized Calibration (METRIC), Surface Energy Balance System (SEBS), Simplified Surface Energy Balance Index (S-SEBI), and Operational Simplified Surface Energy Balance (SSEBop). CWSI estimates from the five SEB models and a simple regression model that used normalized difference vegetation index (NDVI), near-surface temperature difference, and measured soil moisture (SM) as covariates were compared with those derived from eddy covariance measured ET (CWSIEC) for the 32 Landsat image acquisition dates during the 2011 (dry) and 2013 (wet) growing seasons. Results indicate that most SEB models can predict CWSI reasonably well. For example, the root mean square error (RMSE) ranged from 0.14 (SEBAL) to 0.29 (SSEBop) and the coefficient of determination (R2) ranged from 0.25 (SSEBop) to 0.72 (SEBAL), justifying the added complexity in CWSI modeling as compared to results from the simple regression model (R2 = 0.55, RMSE = 0.16). All SEB models underestimated CWSI in the dry year but the estimates from SEBAL and S-SEBI were within 7% of the mean CWSIEC and explained over 60% of variations in CWSIEC. In the wet year, S-SEBI mostly overestimated CWSI (around 28%), while estimates from METRIC, SEBAL, SEBS, and SSEBop were within 8% of the mean CWSIEC. Overall, SEBAL was the most robust model under all conditions followed by METRIC, whose performance was slightly worse and better than SEBAL in dry and wet years

  20. Enhancement of acousto-optical coupling in two-dimensional air-slot phoxonic crystal cavities by utilizing surface acoustic waves

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Tian-Xue [Institute of Engineering Mechanics, Beijing Jiaotong University, Beijing 100044 (China); Wang, Yue-Sheng, E-mail: yswang@bjtu.edu.cn [Institute of Engineering Mechanics, Beijing Jiaotong University, Beijing 100044 (China); Zhang, Chuanzeng [Department of Civil Engineering, University of Siegen, D-57068 Siegen (Germany)

    2017-01-30

    A phoxonic crystal is a periodically patterned material that can simultaneously localize optical and acoustic modes. The acousto-optical coupling in two-dimensional air-slot phoxonic crystal cavities is investigated numerically. The photons can be well confined in the slot owing to the large electric field discontinuity at the air/dielectric interfaces. Besides, the surface acoustic modes lead to the localization of the phonons near the air-slot. The high overlap of the photonic and phononic cavity modes near the slot results in a significant enhancement of the moving interface effect, and thus strengthens the total acousto-optical interaction. The results of two cavities with different slot widths show that the coupling strength is dependent on the slot width. It is expected to achieve a strong acousto-optical/optomechanical coupling in air-slot phoxonic crystal structures by utilizing surface acoustic modes. - Highlights: • Two-dimensional air-slot phoxonic crystal cavities which can confine simultaneously optical and acoustic waves are proposed. • The acoustic and optical waves are highly confined near/in the air-slot. • The high overlap of the photonic and phononic cavity modes significantly enhances the moving interface effect. • Different factors which affect the acousto-optical coupling are discussed.

  1. Evaluating the effect of vehicle impoundment policy on illegal construction and demolition waste dumping: Israel as a case study.

    Science.gov (United States)

    Seror, Nissim; Hareli, Shlomo; Portnov, Boris A

    2014-08-01

    Construction and demolition (C&D) waste dumped alongside roads and in open areas is a major source of soil and underground water pollution. Since 2006, Israeli ministry for environmental protection enacted a policy of vehicle impoundment (VI) according to which track drivers caught while dumping C&D waste illegally have their vehicles impounded. The present study attempted to determine whether the VI policy was effective in increasing the waste hauling to authorized landfill sites, thus limiting the number of illegal unloads of C&D waste at unauthorized landfill sites and in open areas. During the study, changes in the ratio between the monthly amount of C&D waste brought to authorized landfills sites and the estimated total amount of C&D waste generated in different administrative districts of Israel were examined, before and after the enactment of the 2006 VI policy. Short questionnaires were also distributed among local track drivers in order to determine the degree of awareness about the policy in question and estimate its deterrence effects. According to the study's results, in the district of Haifa, in which the VI policy was stringently enacted, the ratio between C&D waste, dumped in authorized landfill sites, and the total amount of generated C&D waste, increased, on the average, from 20% in January 2004 to 35% in October 2009, with the effect attributed to the number of vehicle impoundments being highly statistically significant (t=2.324; p0.1). The analysis of the questionnaires, distributed among the local truck drivers further indicated that the changes observed in the district of Haifa are not coincident and appeared to be linked to the VI policy's enactment. In particular, 62% of the truck drivers, participated in the survey, were aware of the policy and 47% of them personally knew a driver whose vehicle was impounded. Furthermore, the drivers estimated the relative risk of being caught for unloading C&D waste in unauthorized sites, on the average, as

  2. Control of surface wettability by light illumination: surface wettability control utilizing photo-induced surface reaction of titanium oxide; Hikari de nure wo seigyosuru - sanka chitan no hikari reiki hanno wo riyoshtia nure seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T.; Hashimoto, K. [The Universityof Tokyo (Japan)

    1999-02-15

    We report photo-generation of highly hydrophilic surface of titanium dioxide. The photo-induced hydrophilicizing is achieved by photo-generation of Ti{sup 4+} to Ti{sup 3+} at definite sites on the surface, resulting in preferential adsorption of hydroxyl groups on corresponding oxygen vacant sites. We also report the photo-generation of titanium dioxide amphiphilic surface on definite photo illumination condition. The unique character of this surface is ascribed to the microstructure of hydrophilic and oreophilic domain. The hydrophilic or amphiphilic titanium dioxide coating can be applied for antifogging mirror or glass and also self-cleaning paint for various industrial materials. Several commercial applications including antifogging automobile side-view mirror or self-cleaning exterior ceramic tile has been starting to hit the market. (author)

  3. Hydrologic Change during the Colonial Era of the United States: Beavers and the Energy Cost of Impoundments (Invited)

    Science.gov (United States)

    Green, M. B.; Bain, D. J.; Arrigo, J. S.; Duncan, J. M.; Kumar, S.; Parolari, A.; Salant, N.; Vorosmarty, C. J.; Aloysius, N. R.; Bray, E. N.; Ruffing, C. M.; Witherell, B. B.

    2009-12-01

    Europeans colonized North America in the early 17th century with intentions ranging between long-term inhabitation and quick extraction of resources for economic gain in Europe. Whatever the intentions, the colonists relied on the landscape for resources resulting in dramatic change to the forest and fur-bearing mammal population. We demonstrate that initial exploitation of North American forest and furs caused a substantial decrease in mean water residence time (τ) between 1600 and 1800 A.D. That loss, which regionally changed from 51 to 41 days, contrasts with conventional wisdom that humans tend to diminish variability in water resources by increasing storage capacity and thus increasing τ. The loss of τ resulted from over-hunted beaver for the hat market in Europe. Analysis suggests that colonial era demographics and economics did not allow human resource allocation to impoundment construction on a level matching the historic beaver effort. However, the τ appears to have regionally increased during the 19th century, suggesting that humans eventually began replacing the water storage lost with the beaver. The analysis highlights the energy cost of impounding water, which is likely to continue to be an important factor given the increasing need for stable water resources and finite energy resources.

  4. Microcrustaceans (Branchiopoda and Copepoda) of Wetland Ponds and Impoundments on the Savannah River Site, Aiken, South Carolina

    Energy Technology Data Exchange (ETDEWEB)

    Adrienne E. DeBiase; Barbara E. Taylor

    2005-09-21

    The United States Department of Energy's Savannah River Site (SRS) in Aiken, Allendale, and Barnwell Counties, South Carolina, contains an abundance of freshwater wetlands and impoundments. Four large impoundments, as well as several small, abandoned farm and mill ponds, and about 400 Carolina bays and other small, isolated depression wetland ponds are located within the 893 km2 area of the SRS. Crustaceans of the orders Branchiopoda and Copepoda are nearly ubiquitous in these water bodies. Although small in size, these organisms are often very abundant. They consequently play an important trophic role in freshwater food webs supporting fish, larval salamanders, larval insects, and numerous other animals, aquatic and terrestrial. This report provides an introduction to the free-living microcrustaceans of lentic water bodies on the SRS and a comprehensive list of species known to occur there. Occurrence patterns are summarized from three extensive survey studies, supplemented with other published and unpublished records. In lieu of a key, we provide a guide to taxonomic resources and notes on undescribed species. Taxa covered include the orders Cladocera, Anostraca, Laevicaudata, and Spinicaudata of the Subclass Branchiopoda and the Superorders Calanoida and Cyclopoida of Subclass Copepoda. Microcrustaceans of the Superorder Harpacticoida of the Subclass Copepoda and Subclass Ostracoda are also often present in lentic water bodies. They are excluded from this report because they have not received much study at the species level on the SRS.

  5. Avaliação de desinfetantes de superfície utilizados em Odontologia Evaluation of surface disinfectants utilized in dentistry

    Directory of Open Access Journals (Sweden)

    Célia Regina Gonçalves e Silva

    2002-06-01

    Full Text Available Desinfecção de superfície é um procedimento realizado nas áreas externas do equipamento odontológico e demais itens do consultório. O objetivo deste trabalho foi analisar a ação de quatro desinfetantes utilizados em Odontologia: álcool etílico a 77°GL, composto fenólico (Duplofen, iodóforo (PVP-I e solução de álcool etílico a 77°GL com 5% de clorexidina para desinfecção de superfície. Foram analisados quatro pontos em cada equipamento ("carter", pia de lavagem de mãos, encosto de cabeça da cadeira e superfície frontal externa do refletor, utilizando-se a técnica de "spray-wipe-spray". De cada ponto, foram coletadas amostras utilizando-se placas de superfície contendo ágar Mitis Salivarius bacitracina sacarose, ágar Sabouraud Dextrose com cloranfenicol, ágar MacConkey e ágar-sangue para contagem de estreptococos do grupo mutans, leveduras do gênero Candida, bactérias gram-negativas e contagem total de microrganismos, respectivamente (ufc/placa. Os resultados foram analisados estatisticamente utilizando-se teste t de Student para comparação entre as médias de ufc/placa. O desinfetante que demonstrou ser mais efetivo na redução microbiana foi a solução alcoólica de clorexidina, principalmente para bactérias gram-positivas. O iodo e o composto fenólico mostraram ser bastante eficazes na redução microbiana. O álcool etílico a 77°GL foi o menos eficaz dos quatro desinfetantes analisados, mas apesar de não ser indicado como desinfetante de superfície, mostrou, no presente trabalho, redução microbiana estatisticamente significativa após o processo de desinfecção.Surface disinfection is a procedure carried out on the external parts of the dental equipment as well as on other items of the dental office. The aim of this study was to analyze the efficacy of 4 surface disinfectants utilized in dentistry: 77°GL alcohol, phenolic compound (Duplofen, iodophor (PVP-I and 77°GL alcohol with 5% of

  6. Pareto utility

    NARCIS (Netherlands)

    Ikefuji, M.; Laeven, R.J.A.; Magnus, J.R.; Muris, C.H.M.

    2013-01-01

    In searching for an appropriate utility function in the expected utility framework, we formulate four properties that we want the utility function to satisfy. We conduct a search for such a function, and we identify Pareto utility as a function satisfying all four desired properties. Pareto utility

  7. A long-term comparison of carbon sequestration rates in impounded and naturally tidal freshwater marshes along the lower Waccamaw River, South Carolina

    Science.gov (United States)

    Drexler, Judith Z.; Krauss, Ken W.; Sasser, M. Craig; Fuller, Christopher C.; Swarzenski, Christopher M.; Powell, Amber; Swanson, Kathleen M.; Orlando, James L.

    2013-01-01

    Carbon storage was compared between impounded and naturally tidal freshwater marshes along the Lower Waccamaw River in South Carolina, USA. Soil cores were collected in (1) naturally tidal, (2) moist soil (impounded, seasonally drained since ~1970), and (3) deeply flooded “treatments” (impounded, flooded to ~90 cm since ~2002). Cores were analyzed for % organic carbon, % total carbon, bulk density, and 210Pb and 137Cs for dating purposes. Carbon sequestration rates ranged from 25 to 200 g C m−2 yr−1 (moist soil), 80–435 g C m−2 yr−1 (naturally tidal), and 100–250 g C m−2 yr−1 (deeply flooded). The moist soil and naturally tidal treatments were compared over a period of 40 years. The naturally tidal treatment had significantly higher carbon storage (mean = 219 g C m−2 yr−1 vs. mean = 91 g C m−2 yr−1) and four times the vertical accretion rate (mean = 0.84 cm yr−1 vs. mean = 0.21 cm yr−1) of the moist soil treatment. The results strongly suggest that the long drainage period in moist soil management limits carbon storage over time. Managers across the National Wildlife Refuge system have an opportunity to increase carbon storage by minimizing drainage in impoundments as much as practicable.

  8. Water-quality study of Tulpehocken Creek, Berks County, Pennsylvania, prior to impoundment of Blue Marsh Lake

    Science.gov (United States)

    Barker, James L.

    1977-01-01

    Blue Marsh Lake is planned as a multipurpose impoundment to be constructed on Tulpehocken Creek near Bernville, Berks County, Pennsylvania. Prior to construction, samples of water, bed material, and soil were collected throughout the impoundment site to determine concentrations of nutrients, insecticides, trace metals, suspended sediment, and bacteria. Analyses of water suggest the Tulpehocken Creek basin to be a highly fertile environment. Nitrogen and phosphorus concentrations near the proposed dam site had median values of 4.5 and 0.13 mg/L, respectively. Suspended sediment discharges average between 100 and 200 tons (90.7 to 181.4 metric tons) per day during normal flows but may exceed 10,000 tons (9,070 metric tons) per day during storm runoff. Highest yields were measured during winter and early spring. Concentrations range from 3 mg/L to more than 500 mg/L. Bed material samples contain trace quantities of aldrin, DDT, DDD, DDE, dieldrin, and chlordane. Polychlorinated biphyenyls (PCB's) ranged from 10 to 100 μg/kg. Soils at the impoundment site are of average fertility. However, the silt loam texture is ideal for attachment and growth of aquatic plants. Bacteria populations indicative of recent fecal contamination are prevalent in the major inflows to the proposed lake. Fecal Coliform exceeded the standards recommended by the Federal Water Pollution Administration Committee on Water Quality Criteria for public water supply in 29 percent of the monthly samples, and exceeded the recommended public bathing waters standard in 83 percent of the samples collected from June to September. Arsenic from an industrial waste was found in the water, suspended sediment, and bed material of Tulpehocken Creek in concentrations of 0 to 30 μg/l, 2 to 879 μg/l, and 1 to 79 μg/g, respectively. It represents a potential environmental hazard; however, the measured concentrations are less than that known to be harmful to man, fish, or wildlife, according to published water

  9. Uptake of uranium, thorium and radium isotopes by plants growing in dam impoundment Tasotkel and the Lower Shu region (Kazakhstan)

    Energy Technology Data Exchange (ETDEWEB)

    Matveyeva, Ilona; Burkitbayev, Mukhambetkali [al-Farabi Kazakh National University, Almaty (Kazakhstan). Faculty of Chemistry and Chemical Technology; Jacimovic, Radojko [Jozef Stefan Institute, Ljubljana (Slovenia). Dept. of Environmental Sciences; Planinsek, Petra; Smodis, Borut [Jozef Stefan Institute, Ljubljana (Slovenia). Dept. of Environmental Sciences; Jozef Stefan International Postgraduate School, Ljubljana (Slovenia)

    2016-04-01

    The activity concentrations of isotopes of uranium, thorium and radium-226 in dominant species of plants (Xantium strumarium, Phragmites communis, Artemisia nitrosa and Artemisia serotina) growing on the territories contaminated by uranium industry of Kazakhstan (close to dam impoundment Tasotkel and the Lower Shu region) are presented. The obtained data showed the significant variations of activity concentrations of isotopes of uranium, thorium and radium-226 in above ground parts. The concentrations of most of the investigated radionuclides in the root system are higher than in the aboveground parts; it can be explained by root barrier. It was found that the highest root barrier has Xantium strumarium, especially for uranium isotopes. The concentration ratios of radionuclides were calculated, and as the result it was found that the highest accumulation ability in the investigated region has Artemisia serotina.

  10. Proceedings of the 15. annual British Columbia MEND ML/ARD workshop : the management of tailings and tailings impoundments

    International Nuclear Information System (INIS)

    2009-02-01

    This Mine Environment Neutral Drainage (MEND) workshop was held to promote the exchange of information and ideas on environmental protection and reclamation associated with mining. The workshop covered a broad spectrum of reclamation issues and the key environmental challenges facing the mining industry, such as acid mine drainage (AMD) control, and metal leaching and acid rock drainage (ML/ARD). The theme for the 2008 workshop was the management of tailings and tailings impoundments. Topics of discussion included hydrogeology and geochemistry; tailings disposal; mitigation; closure plans; and postclosure performance. The emphasis was on full-scale case studies, practical constraints and sustaining successful disposal strategies and remediation. The session on tailings management reviewed overarching policies and practices; methods of subaerial tailings disposal and case studies of tailings management; and detailed investigations of geochemical properties and processes. The conference featured 22 presentations, of which 4 have been catalogued separately for inclusion in this database. refs., tabs., figs

  11. Effects of a drawdown on plant communities in a freshwater impoundment at Lacassine National Wildlife Refuge, Louisiana

    Science.gov (United States)

    Howard, Rebecca J.; Allain, Larry

    2012-01-01

    Disturbance is an important natural process in the creation and maintenance of wetlands. Water depth manipulation and prescribed fire are two types of disturbance commonly used by humans to influence vegetation succession and composition in wetlands with the intention of improving wildlife habitat value. A 6,475-hectare (ha) impoundment was constructed in 1943 on Lacassine National Wildlife Refuge in southwest Louisiana to create freshwater wetlands as wintering waterfowl habitat. Ten years after construction of the impoundment, called Lacassine pool, was completed, refuge staff began expressing concerns about increasing emergent vegetation cover, organic matter accumulation, and decreasing area of open water within the pool. Because the presence of permanent standing water impedes actions that can address these concerns, a small impoundment within the pool where it was possible to manipulate water depth was created. The 283-ha subimpoundment called Unit D was constructed in 1989. Water was pumped from Unit D in 1990, and the unit was permanently reflooded about 3 years later. Four prescribed fires were applied during the drawdown. A study was initiated in 1990 to investigate the effect of the experimental drawdown on vegetation and soils in Unit D. Four plant community types were described, and cores were collected to measure the depth of the soil organic layer. A second study of Unit D was conducted in 1997, 4 years after the unit was reflooded, by using the same plots and similar sampling methods. This report presents an analysis and synthesis of the data from the two studies and provides an evaluation of the impact of the management techniques applied. We found that plant community characteristics often differed among the four communities and varied with time. Species richness increased in two of the communities, and total aboveground biomass increased in all four during the drawdown. These changes, however, did not persist when Unit D was reflooded; by 1997

  12. Change characteristics of DSi and nutrition structure at the Yangtze River Estuary after Three Gorges Project impounding and their ecological effect

    Directory of Open Access Journals (Sweden)

    Li Lei

    2017-06-01

    Full Text Available The variation law of dissolved silica (DSi, dissolved inorganic nitrogen (DIN, dissolved inorganic phosphorus (DIP and nutrition structure after the Three Gorges Project (TGP impounding as well as their ecological effect were analyzed according to monitoring survey of the Yangtze River Estuary in spring (May and summer (August from 2004-2009. The results showed that after impounding, DSi and DIN concentration decreased and increased, respectively. During the study period, DSi decreased by about 63%, while DIN almost tripled. DIP concentration fluctuated slightly. With respect to nutrition structure, N:P increased, whereas Si:P and Si:N declined. According to chemometry standard of nutrient limits, nutrition structure tended to be imbalanced and the limiting factor of phytoplankton growth (P was studied. Changes of nutrition structure have largely decreased diatom and caused different composition of dominant phytoplankton species. This may change ecosystem structure of the Yangtze River Estuary.

  13. Synchronous response of sedimentary organic carbon accumulation on the inner shelf of the East China Sea to the water impoundment of Three Gorges and Gezhouba Dams

    Science.gov (United States)

    Lin, Jia; Zhu, Qing; Hong, Yuehui; Yuan, Lirong; Liu, Jinzhong; Xu, Xiaoming; Wang, Jianghai

    2018-01-01

    Coastal seas, located between continents and the open ocean, are an important active carbon pool. The sedimentary total organic carbon (TOC) in these areas is a mixture of terrestrial and marine sources, and can be a powerful proxy for tracing natural processes and human activities. In this study, one fine-grained sediment core (DH5-1) from the inner shelf of the East China Sea was systematically analyzed for TOC and black carbon (BC) contents and TOC stable carbon isotope ratios (δ13C). By combining these data with 210Pb dating, an improved carbon correction model and a two end-member mixing model, we reconstructed century-scale high-resolution sequences of corrected TOC, terrestrial TOC and marine TOC contents and identified two carbon depletion events in the DH5-1 record. The two events, shown as two minima in the TOC profiles, correspond temporally to 1985-1987 AD and 2003-2006 AD, which exactly matches the water impoundment of the Gezhouba Dam and Three Gorges Dam, respectively. In addition, the variations in TOC contents and δ13C values before, during or after the minima demonstrate a relationship between the depletion events and water impoundment of the dams on the Changjiang River. The TOC reductions may represent synchronous responses of sedimentary TOC and resultant ecological effects on the inner shelf of the East China Sea to the water impoundment of the dams. These new TOC records reflect the interaction between natural and anthropogenic processes and, accordingly, provide a deep insight and important references for assessing marine ecological effects resulting from water impoundment of largescale dams.

  14. 30 CFR 784.16 - Reclamation plan: Siltation structures, impoundments, and refuse piles.

    Science.gov (United States)

    2010-07-01

    ... AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND... with assistance from experts in related fields such as landscape architecture; (ii) Contain a... related fields such as geology, land surveying, and landscape architecture; (B) Include any geotechnical...

  15. 30 CFR 780.25 - Reclamation plan: Siltation structures, impoundments, and refuse piles.

    Science.gov (United States)

    2010-07-01

    ... AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND..., with assistance from experts in related fields such as landscape architecture; (ii) Contain a... related fields such as geology, land surveying, and landscape architecture; (B) Include any geotechnical...

  16. Overland erosion of uranium-mill-tailings impoundments: physical processes and computational methods

    International Nuclear Information System (INIS)

    Walters, M.H.

    1983-03-01

    The surface runoff and erosional processes of watersheds caused by rainfall-runoff are reviewed. Soil properties, topography, and rainstorm distribution are discussed with respect to their effects on soil erosion. The effects of climate and vegetation are briefly presented. Regression models and physical process simulation models are reviewed

  17. Resource use by the facultative lepidophage Roeboides affinis (Günther, 1868: a comparison of size classes, seasons and environment types related to impoundment

    Directory of Open Access Journals (Sweden)

    Miriam P. Albrecht

    Full Text Available We report the consumption of scales and other food resources by the facultative lepidophage Roeboides affinis in the upper Tocantins River where it was impounded by the Serra da Mesa Hydroelectric Dam. We compared the diet among size classes, between dry and wet seasons, and between sites with distinct water flow characteristics (lotic vs. lentic related to the distance from the dam and phase of reservoir development. As transparency and fish abundance increased after impoundment, we expected a higher consumption of scales in lentic sites. Likewise, habitat contraction, higher transparency and decrease in terrestrial resources availability, would promote a higher consumption of scales. Scales were consumed by 92% of individuals and represented 26% of the total volume of resources ingested by R. affinis. Diet composition varied significantly among size classes, with larger individuals consuming more scales and larger items, especially odonatans and ephemeropterans. Scale consumption was not significantly different between dry and wet seasons. Roeboides affinis incorporated some food items into the diet as a response to the impoundment, like other species. Scale consumption was higher in lotic sites, refuting our initial hypothesis, what suggests that the lepidophagous habit is related the rheophilic nature of R. affinis.

  18. Mercury concentrations of fish in Southern Indian Lake and Issett Lake, Manitoba 1975-88: The effect of lake impoundment and Churchill River diversion

    International Nuclear Information System (INIS)

    Strange, N.E.; Bodaly, R.A.; Fudge, R.J.P.

    1991-01-01

    Southern Indian and Issett Lakes in northern Manitoba were flooded in 1976 as part of Manitoba Hydro's Churchill River diversion project. Fish were collected from 1975 to 1988 from five regional sites on the lakes to examine the effects of impoundment and river diversion on muscle mercury concentrations. Raw data for individual fish caught in 1987 and 1988 are presented, along with means and analyses calculated over the entire 1975-1988 study period. Mercury concentrations in whitefish, pike, and walleye increased significantly after impoundment. Whitefish mercury levels peaked in 1978 and have since declined to near pre-flooding levels. Northern pike and walleye mercury levels were much higher than for whitefish. Pike mercury concentrations showed no indication of declining after 12 years of impoundment, but walleye mercury levels at 2 of the 5 Southern Indian Lake sites declined from maximum recorded levels. Significant variability in fish mercury concentrations was noted both from year to year and among the sites. It is suggested that site-to-site variations are due to varying conditions in the reservoir which stimulate mercury methylation. Since there appears to be an ongoing long-term source of mercury and organic material from the eroding shorelines, pike and walleye mercury concentrations are expected to remain high for many years. 25 refs., 7 figs., 20 tabs

  19. Geochemical characterisation of seepage and drainage water quality from two sulphide mine tailings impoundments: Acid mine drainage versus neutral mine drainage

    Science.gov (United States)

    Heikkinen, P.M.; Raisanen, M.L.; Johnson, R.H.

    2009-01-01

    Seepage water and drainage water geochemistry (pH, EC, O2, redox, alkalinity, dissolved cations and trace metals, major anions, total element concentrations) were studied at two active sulphide mine tailings impoundments in Finland (the Hitura Ni mine and Luikonlahti Cu mine/talc processing plant). The data were used to assess the factors influencing tailings seepage quality and to identify constraints for water treatment. Changes in seepage water quality after equilibration with atmospheric conditions were evaluated based on geochemical modelling. At Luikonlahti, annual and seasonal changes were also studied. Seepage quality was largely influenced by the tailings mineralogy, and the serpentine-rich, low sulphide Hitura tailings produced neutral mine drainage with high Ni. In contrast, drainage from the high sulphide, multi-metal tailings of Luikonlahti represented typical acid mine drainage with elevated contents of Zn, Ni, Cu, and Co. Other factors affecting the seepage quality included weathering of the tailings along the seepage flow path, process water input, local hydrological settings, and structural changes in the tailings impoundment. Geochemical modelling showed that pH increased and some heavy metals were adsorbed to Fe precipitates after net alkaline waters equilibrated with the atmosphere. In the net acidic waters, pH decreased and no adsorption occurred. A combination of aerobic and anaerobic treatments is proposed for Hitura seepages to decrease the sulphate and metal loading. For Luikonlahti, prolonged monitoring of the seepage quality is suggested instead of treatment, since the water quality is still adjusting to recent modifications to the tailings impoundment.

  20. DC resistivity and IP methods in acid mine drainage problems: results from the Copper Cliff mine tailings impoundments

    Science.gov (United States)

    Yuval, Douglas; Oldenburg, W.

    1996-04-01

    Oxidation of sulfide minerals in the mine tailings impoundments at Copper Cliff, Ontario generates acidic conditions and elevated concentrations of dissolved metals and sulfates in the pore water. The pore water migrates away from the tailings to pose a potential environmental hazard if is should reach nearby water systems. There is a need to characterize this potential environmental problem and to assess the future hazards. A combined DC resistivity and induced polarization (IP) survey was carried out along one of the major flowpaths in the tailings and the data were inverted to produce detailed electrical conductivity and chargeability structures of the cross-section below the survey line. The conductivity distributions are directly translated, through theoretical and empirical relations, to a map of the concentration of the total dissolved solids (TDS) along the cross-section and thereby provide insight about the in-situ pore water quality. The sulfide minerals are the source of the IP response and, thus, when combined with borehole data, the chargeability model can be used to estimate the amount and distribution of the sulfides.

  1. Restoring tides to reduce methane emissions in impounded wetlands: A new and potent Blue Carbon climate change intervention

    Science.gov (United States)

    Kroeger, Kevin D.; Crooks, Stephen; Moseman-Valtierra, Serena; Tang, Jianwu

    2017-01-01

    Coastal wetlands are sites of rapid carbon (C) sequestration and contain large soil C stocks. Thus, there is increasing interest in those ecosystems as sites for anthropogenic greenhouse gas emission offset projects (sometimes referred to as “Blue Carbon”), through preservation of existing C stocks or creation of new wetlands to increase future sequestration. Here we show that in the globally-widespread occurrence of diked, impounded, drained and tidally-restricted salt marshes, substantial methane (CH4) and CO2 emission reductions can be achieved through restoration of disconnected saline tidal flows. Modeled climatic forcing indicates that tidal restoration to reduce emissions has a much greater impact per unit area than wetland creation or conservation to enhance sequestration. Given that GHG emissions in tidally-restricted, degraded wetlands are caused by human activity, they are anthropogenic emissions, and reducing them will have an effect on climate that is equivalent to reduced emission of an equal quantity of fossil fuel GHG. Thus, as a landuse-based climate change intervention, reducing CH4 emissions is an entirely distinct concept from biological C sequestration projects to enhance C storage in forest or wetland biomass or soil, and will not suffer from the non-permanence risk that stored C will be returned to the atmosphere.

  2. Restoring tides to reduce methane emissions in impounded wetlands: A new and potent Blue Carbon climate change intervention.

    Science.gov (United States)

    Kroeger, Kevin D; Crooks, Stephen; Moseman-Valtierra, Serena; Tang, Jianwu

    2017-09-20

    Coastal wetlands are sites of rapid carbon (C) sequestration and contain large soil C stocks. Thus, there is increasing interest in those ecosystems as sites for anthropogenic greenhouse gas emission offset projects (sometimes referred to as "Blue Carbon"), through preservation of existing C stocks or creation of new wetlands to increase future sequestration. Here we show that in the globally-widespread occurrence of diked, impounded, drained and tidally-restricted salt marshes, substantial methane (CH 4 ) and CO 2 emission reductions can be achieved through restoration of disconnected saline tidal flows. Modeled climatic forcing indicates that tidal restoration to reduce emissions has a much greater impact per unit area than wetland creation or conservation to enhance sequestration. Given that GHG emissions in tidally-restricted, degraded wetlands are caused by human activity, they are anthropogenic emissions, and reducing them will have an effect on climate that is equivalent to reduced emission of an equal quantity of fossil fuel GHG. Thus, as a landuse-based climate change intervention, reducing CH 4 emissions is an entirely distinct concept from biological C sequestration projects to enhance C storage in forest or wetland biomass or soil, and will not suffer from the non-permanence risk that stored C will be returned to the atmosphere.

  3. Nonmetals Test and Evaluation: Delivery Order 0007: The Development of On-Aircraft Surface Preparations Utilizing Sol-Gel Coatings for Adhesive Bonding Aluminum Alloys

    National Research Council Canada - National Science Library

    McCray, Daniel

    2001-01-01

    ...), and hexavalent chromium. Surface preparations used for on-aircraft repair of aluminum rely on hazardous materials or inconvenient processing steps, or they do not yield adequate bond performance. Grit-blast/silane (GBS...

  4. Influence of vegetation and sewage sludge on sealing layer of fly ashes in post-treatment of mine tailings impoundments; Inverkan av vegetation och roetslam paa taetskikt av flygaska vid efterbehandling av sandmagasin

    Energy Technology Data Exchange (ETDEWEB)

    Greger, Maria; Neuschuetz, Clara (Inst. of Bothany, Stockholm Univ., Stockholm (Sweden)); Isaksson, Karl-Erik (Boliden Mineral AB, Stockholm (Sweden))

    2009-03-15

    Mining industry produces 25 Mton mine tailings yearly that are deposited in impoundments in the nature. When this sand, containing sulphur rich minerals, reacts with oxygen and water it starts to weather and acidic metal rich water is formed. To prevent this, the sand can be covered with a sealing layer and a protective cover layer with vegetation. As sealing and cover materials fly ashes and sewage sludge can be used. The aim of this investigation was to find out: 1) how sealing layer of fly ashes with and without sewage sludge, and a cover with sewage sludge can be placed practically on mine tailings in a cold climate. 2) how such a cover should be constructed to minimize the risk of root penetration and leakage of nutrients and metals 3) which vegetation that is most suitable This was investigated in field- and greenhouse tests with a sealing layer of fly ash and/or sewage sludge with a cover layer of sewage sludge in which different plant species were established. The practical application was performed in 0.3-1 ha plots at a mine tailings impoundments at Boliden. The ability of plant roots to penetrate a sealing layer was investigated, as well as the effect of simulated root exudates on the penetration resistance in hardened ash. Leakage of nutrients and metals from cover layer of sewage sludge, in some cases with sealing layers beneath, was investigated in field and greenhouse lysimeters. Various plant species were compared on their ability to affect metal and nutrient leakage as well as root penetration and shattering of the hardened ashes. The project was a cooperation between Stockholm University and Boliden Mineral AB, and the field tests were performed at the impoundment Gillervattnet in Boliden and in Garpenberg. Cooperating were also Iggesund Paperboard, Skellefteaa Kraft, Stora Enso Fors, Umeaa Energi and Vattenfall, all producers of ashes that were used, as well as Stockholm Vatten AB, which produced the sewage sludge. The most important conclusions

  5. Estimating Utility

    DEFF Research Database (Denmark)

    Arndt, Channing; Simler, Kenneth R.

    2010-01-01

    A fundamental premise of absolute poverty lines is that they represent the same level of utility through time and space. Disturbingly, a series of recent studies in middle- and low-income economies show that even carefully derived poverty lines rarely satisfy this premise. This article proposes...... an information-theoretic approach to estimating cost-of-basic-needs (CBN) poverty lines that are utility consistent. Applications to date illustrate that utility-consistent poverty measurements derived from the proposed approach and those derived from current CBN best practices often differ substantially......, with the current approach tending to systematically overestimate (underestimate) poverty in urban (rural) zones....

  6. Adsorption of CO on Ru and Pt blacks and catalysts and the possibility of its utilization for the determination of the ruthenium-free surface

    Czech Academy of Sciences Publication Activity Database

    Paseka, Ivo

    2007-01-01

    Roč. 11, č. 1 (2007), s. 52-58 ISSN 1432-8488 R&D Projects: GA ČR(CZ) GA104/03/0409 Institutional research plan: CEZ:AV0Z40320502 Keywords : hydrogen/ carbon monoxide adsorption * platinum/ruthenium catalysts * specific surface Subject RIV: CA - Inorganic Chemistry Impact factor: 1.535, year: 2007

  7. Characterization of large surface area polymer monoliths and their utility for rapid, selective solid phase extraction for improved sample clean up.

    Science.gov (United States)

    Candish, Esme; Wirth, Hans-Jürgen; Gooley, Andrew A; Shellie, Robert A; Hilder, Emily F

    2015-09-04

    While polymer monoliths are widely described for solid phase extraction (SPE), appropriate characterization is rarely provided to unravel the links between physical characteristics and observed advantages and disadvantages. Two known approaches to fabricate large surface area polymer monoliths with a bimodal pore structure were investigated. The first incorporated a high percentage of divinyl benzene (PDVB) and the second explored hypercrosslinking of pre-formed monoliths. Adsorption of probe analytes; anisole, benzoic acid, cinnamic acid, ibuprofen and cortisone were investigated using frontal analysis and the SPE performance was compared with particulate adsorbents. Frontal analysis of anisole described maximum adsorption capacities of 164mgg(-1) and 298mgg(-1) for hypercrosslinked and PDVB adsorbents, respectively. The solvated state specific surface area was calculated to be 341 and 518m(2)g(-1) respectively. BET revealed a hypercrosslinked surface area of 817m(2)g(-1), 2.5 times greater than in the solvated state. The PDVB BET surface area was 531m(2)g(-1), similar to the solvated state. Micropores of 1nm provided the enhanced surface area for hypercrosslinked adsorbents. PDVB displayed a pore size distribution of 1-6nm. Frontal analysis demonstrated the micropores present size exclusion for the larger probes. Recovery of anisole was determined by SPE using 0.4 and 1.0mLmin(-1). Recovery for PDVB remained constant at 90%±0.103 regardless of the extraction flow rate suggesting extraction performance is independent of flow rate. A more efficient sample purification of saccharin in urine was yielded by PDVB due to selective permeation of the small pores. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. Oxygen and silicon stable isotopes of diatom silica. Reconstructing changes in surface water hydrography and silicic acid utilization in the late Pleistocene subarctic Pacific

    International Nuclear Information System (INIS)

    Maier, Edith

    2014-01-01

    Deglacial variations in upper ocean nutrient dynamics and stratification in high latitudes, as well as associated changes in thermohaline overturning circulation, are thought to have played a key role in changing atmospheric CO 2 concentrations. This thesis examines the relationship between past changes in subarctic Pacific upper ocean stratification and nutrient (silicic acid) utilization, using oxygen and silicon stable isotopes of diatom silica, for the first time at millennial-scale resolution and analyzed with a new and efficient instrumentation set-up. The isotopic data, presented in three manuscripts, show a consistent picture of millennial-scale variability in upper ocean stratification and silicic acid utilization during the last ∝50 ka BP, e.g. indicating that the subarctic Pacific was a source region for atmospheric CO 2 during the last deglaciation (late Heinrich Stadial 1 and the Boelling/Alleroed). The presented results demonstrate the high potential of combined diatom oxygen and silicon stable isotope analysis especially for, but not restricted to, marine regions characterized by a low biogenic carbonate content like the subarctic Pacific and the Southern Ocean.

  9. Oxygen and silicon stable isotopes of diatom silica. Reconstructing changes in surface water hydrography and silicic acid utilization in the late Pleistocene subarctic Pacific

    Energy Technology Data Exchange (ETDEWEB)

    Maier, Edith

    2014-03-05

    Deglacial variations in upper ocean nutrient dynamics and stratification in high latitudes, as well as associated changes in thermohaline overturning circulation, are thought to have played a key role in changing atmospheric CO{sub 2} concentrations. This thesis examines the relationship between past changes in subarctic Pacific upper ocean stratification and nutrient (silicic acid) utilization, using oxygen and silicon stable isotopes of diatom silica, for the first time at millennial-scale resolution and analyzed with a new and efficient instrumentation set-up. The isotopic data, presented in three manuscripts, show a consistent picture of millennial-scale variability in upper ocean stratification and silicic acid utilization during the last ∝50 ka BP, e.g. indicating that the subarctic Pacific was a source region for atmospheric CO{sub 2} during the last deglaciation (late Heinrich Stadial 1 and the Boelling/Alleroed). The presented results demonstrate the high potential of combined diatom oxygen and silicon stable isotope analysis especially for, but not restricted to, marine regions characterized by a low biogenic carbonate content like the subarctic Pacific and the Southern Ocean.

  10. Flow of 3D Eyring-Powell fluid by utilizing Cattaneo-Christov heat flux model and chemical processes over an exponentially stretching surface

    Science.gov (United States)

    Hayat, Tanzila; Nadeem, S.

    2018-03-01

    This paper examines the three dimensional Eyring-Powell fluid flow over an exponentially stretching surface with heterogeneous-homogeneous chemical reactions. A new model of heat flux suggested by Cattaneo and Christov is employed to study the properties of relaxation time. From the present analysis we observe that there is an inverse relationship between temperature and thermal relaxation time. The temperature in Cattaneo-Christov heat flux model is lesser than the classical Fourier's model. In this paper the three dimensional Cattaneo-Christov heat flux model over an exponentially stretching surface is calculated first time in the literature. For negative values of temperature exponent, temperature profile firstly intensifies to its most extreme esteem and after that gradually declines to zero, which shows the occurrence of phenomenon (SGH) "Sparrow-Gregg hill". Also, for higher values of strength of reaction parameters, the concentration profile decreases.

  11. Evaluation of the Effects of Utilizing Carbon Dioxide as a Pulpal Test. Part I. In Vitro Effect on Human Enamel Surface.

    Science.gov (United States)

    1982-05-21

    to be a safe test. INTRODUCTION Thermal testing has proven one of the most predictable tests in endodontics .1 -3 In the United States, for cold...Microscope, Advanced Metals Research Corp, Wooten, Mass). Photographs of the surface were made at 30, 100, and 600 magnifications (Fig 2, 3B-D). Prior to and...confirmed by the SEM. The SEM photomicrographs at 100 magnification were excellent for evaluating the fissures (Fig 2B,E,H). At this , magnification , very

  12. Large area compatible broadband superabsorber surfaces in the VIS-NIR spectrum utilizing metal-insulator-metal stack and plasmonic nanoparticles.

    Science.gov (United States)

    Dereshgi, Sina Abedini; Okyay, Ali Kemal

    2016-08-08

    Plasmonically enhanced absorbing structures have been emerging as strong candidates for photovoltaic (PV) devices. We investigate metal-insulator-metal (MIM) structures that are suitable for tuning spectral absorption properties by modifying layer thicknesses. We have utilized gold and silver nanoparticles to form the top metal (M) region, obtained by dewetting process compatible with large area processes. For the middle (I) and bottom (M) layers, different dielectric materials and metals are investigated. Optimum MIM designs are discussed. We experimentally demonstrate less than 10 percent reflection for most of the visible (VIS) and near infrared (NIR) spectrum. In such stacks, computational analysis shows that the bottom metal is responsible for large portion of absorption with a peak of 80 percent at 1000 nm wavelength for chromium case.

  13. On the Utilization of Ice Flow Models and Uncertainty Quantification to Interpret the Impact of Surface Radiation Budget Errors on Estimates of Greenland Ice Sheet Surface Mass Balance and Regional Estimates of Mass Balance

    Science.gov (United States)

    Schlegel, N.; Larour, E. Y.; Gardner, A. S.; Lang, C.; Miller, C. E.; van den Broeke, M. R.

    2016-12-01

    How Greenland ice flow may respond to future increases in surface runoff and to increases in the frequency of extreme melt events is unclear, as it requires detailed comprehension of Greenland surface climate and the ice sheet's sensitivity to associated uncertainties. With established uncertainty quantification tools run within the framework of Ice Sheet System Model (ISSM), we conduct decadal-scale forward modeling experiments to 1) quantify the spatial resolution needed to effectively force distinct components of the surface radiation budget, and subsequently surface mass balance (SMB), in various regions of the ice sheet and 2) determine the dynamic response of Greenland ice flow to variations in components of the net radiation budget. The Glacier Energy and Mass Balance (GEMB) software is a column surface model (1-D) that has recently been embedded as a module within ISSM. Using the ISSM-GEMB framework, we perform sensitivity analyses to determine how perturbations in various components of the surface radiation budget affect model output; these model experiments allow us predict where and on what spatial scale the ice sheet is likely to dynamically respond to changes in these parameters. Preliminary results suggest that SMB should be forced at at least a resolution of 23 km to properly capture dynamic ice response. In addition, Monte-Carlo style sampling analyses reveals that the areas with the largest uncertainty in mass flux are located near the equilibrium line altitude (ELA), upstream of major outlet glaciers in the North and West of the ice sheet. Sensitivity analysis indicates that these areas are also the most vulnerable on the ice sheet to persistent, far-field shifts in SMB, suggesting that continued warming, and upstream shift in the ELA, are likely to result in increased velocities, and consequentially SMB-induced thinning upstream of major outlet glaciers. Here, we extend our investigation to consider various components of the surface radiation

  14. Utilization of satellite remote sensing data on land surface characteristics in water and heat balance component modeling for vegetation covered territories

    Science.gov (United States)

    Muzylev, Eugene; Uspensky, Alexander; Startseva, Zoya; Volkova, Elena; Kukharsky, Alexander; Uspensky, Sergey

    2010-05-01

    The model of vertical water and heat transfer in the "soil-vegetation-atmosphere" system (SVAT) for vegetation covered territory has been developed, allowing assimilating satellite remote sensing data on land surface condition as well as accounting for heterogeneities of vegetation and meteorological characteristics. The model provides the calculation of water and heat balance components (such as evapotranspiration Ev, soil water content W, sensible and latent heat fluxes and others ) as well as vertical soil moisture and temperature distributions, temperatures of soil surface and foliage, land surface brightness temperature for any time interval within vegetation season. To describe the landscape diversity soil constants and leaf area index LAI, vegetation cover fraction B, and other vegetation characteristics are used. All these values are considered to be the model parameters. Territory of Kursk region with square about 15 thousands km2 situated in the Black Earth zone of Central Russia was chosen for investigation. Satellite-derived estimates of land surface characteristics have been constructed under cloud-free condition basing AVHRR/NOAA, MODIS/EOS Terra and EOS Aqua, SEVIRI/Meteosat-8, -9 data. The developed technologies of AVHRR data thematic processing have been refined providing the retrieval of surface skin brightness temperature Tsg, air foliage temperature Ta, efficient surface temperature Ts.eff and emissivity E, as well as derivation of vegetation index NDVI, B, and LAI. The linear regression estimators for Tsg, Ta and LAI have been built using representative training samples for 2003-2009 vegetation seasons. The updated software package has been applied for AVHRR data thematic processing to generate named remote sensing products for various dates of the above vegetation seasons. The error statistics of Ta, Ts.eff and Тsg derivation has been investigated for various samples using comparison with in-situ measurements that has given RMS errors in the

  15. Monitoring peak power and cooling energy savings of shade trees and white surfaces in the Sacramento Municipal Utility District (SMUD) service area: Project design and preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Akbari, H.; Bretz, S.; Hanford, J.; Rosenfeld, A.; Sailor, D.; Taha, H. [Lawrence Berkeley Lab., CA (United States); Bos, W. [Sacramento Municipal Utility District, CA (United States)

    1992-12-01

    Urban areas in warm climates create summer heat islands of daily average intensity of 3--5{degrees}C, adding to discomfort and increasing air-conditioning loads. Two important factors contributing to urban heat islands are reductions in albedo (lower overall city reflectance) and loss of vegetation (less evapotranspiration). Reducing summer heat islands by planting vegetation (shade trees) and increasing surface albedos, saves cooling energy, allows down-sizing of air conditioners, lowers air-conditioning peak demand, and reduces the emission of CO{sub 2} and other pollutants from electric power plants. The focus of this multi-year project, jointly sponsored by SMUD and the California Institute for Energy Efficiency (CIEE), was to measure the direct cooling effects of trees and white surfaces (mainly roofs) in a few buildings in Sacramento. The first-year project was to design the experiment and obtain base case data. We also obtained limited post retrofit data for some sites. This report provides an overview of the project activities during the first year at six sites. The measurement period for some of the sites was limited to September and October, which are transitional cooling months in Sacramento and hence the interpretation of results only apply to this period. In one house, recoating the dark roof with a high-albedo coating rendered air conditioning unnecessary for the month of September (possible savings of up to 10 kWh per day and 2 kW of non-coincidental peak power). Savings of 50% relative to an identical base case bungalow were achieved when a school bungalow`s roof and southeast wall were coated with a high-albedo coating during the same period. Our measured data for the vegetation sites do not indicate conclusive results because shade trees were small and the cooling period was almost over. We need to collect more data over a longer cooling season in order to demonstrate savings conclusively.

  16. Prevalence of gastrointestinal parasites of stray dogs impounded by the Society for the Prevention of Cruelty to Animals (SPCA), Durban and Coast, South Africa.

    Science.gov (United States)

    Mukaratirwa, S; Singh, V P

    2010-06-01

    Coprological examination was used to determine the prevalence and intensity of gastrointestinal parasites of stray dogs impounded by the Society for the Prevention of Cruelty to Animals (SPCA), Durban and Coast, South Africa. Helminth and protozoan parasites were found in faeces of 240 dogs with an overall prevalence of 82.5% (helminth parasites 93.1% and protozoan parasites 6.9%). The following parasites and their prevalences were detected; Ancylostoma sp. (53.8%), Trichuris vulpis (7.9%), Spirocerca lupi (5.4%), Toxocara canis (7.9%), Toxascaris leonina (0.4%) Giardia intestinalis (5.6%) and Isospora sp. (1.3%). Dogs harbouring a single parasite species were more common (41.7%) than those harbouring 2 (15%) or multiple (2.1%) species. Ancylostoma sp., Toxocara canis and Giardia intestinalis have zoonotic potential and were detected in 66.7% of the samples.

  17. Prevalence of gastrointestinal parasites of stray dogs impounded by the Society for the Prevention of Cruelty to Animals (SPCA, Durban and Coast, South Africa : short communication

    Directory of Open Access Journals (Sweden)

    S. Mukaratirwa

    2010-05-01

    Full Text Available Coprological examination was used to determine the prevalence and intensity of gastrointestinal parasites of stray dogs impounded by the Society for the Prevention of Cruelty to Animals (SPCA, Durban and Coast, South Africa. Helminth and protozoan parasites were found in faeces of 240 dogs with an overall prevalence of 82.5% (helminth parasites 93.1% and protozoan parasites 6.9 %. The following parasites and their prevalences were detected; Ancylostoma sp. (53.8 %, Trichuris vulpis (7.9 %, Spirocerca lupi (5.4 %, Toxocara canis (7.9 %, Toxascaris leonina (0.4 % Giardia intestinalis (5.6 % and Isospora sp. (1.3 %. Dogs harbouring a single parasite species were more common (41.7 % than those harbouring 2 (15 % or multiple (2.1 % species. Ancylostoma sp., Toxocara canis and Giardia intestinalis have zoonotic potential and were detected in 66.7 % of the samples.

  18. Changes in the fish community of the Kpong Headpond, lower Volta River, Ghana after 25 years of impoundment

    Directory of Open Access Journals (Sweden)

    Theodore Quarcoopome

    2011-12-01

    Full Text Available The Kpong Headpond was the second created on the Volta River after Akosombo Dam, primarily as a source of hydroelectric power generation and potable water supply, and additionally, it has supported some fish production in Ghana since impoundment. The changes in fish community of the Kpong Headpond were studied to provide baseline information for strategies formulation to support the socio-economic development of the reservoir. The study identified changes in the fish community of the reservoir by comparing occurrence, composition, relative abundance and relative importance estimates of fish species, families and trophic groups, from available previous studies in the reservoir. From the collated information all fishes identified in the reservoir were categorised based on occurrence and importance as disappeared, appeared, permanent, declined or important, to show current status. The results indicated that the fish community has experienced a shift in the composition and relative abundance of important species, families and trophic groups in terms of number and weight, while remaining ecologically balanced. Representatives of the families Osteoglossidae, Centropomidae and Characidae have declined while representatives of the families Claroteidae, Cyprinidae and Cichlidae have increased. The aufwuch-detritus and herbivores declined while semi-pelagic omnivores increased resulting in a shift in dominance to benthic and semi pelagic omnivores. The appearance of five species and the disappearance of 25 others indicated a dynamic restructuring of the fish community in the reservoir, as expected. Enforcement of fishing regulations including the use of appropriate gear and fishing methods, fishery access control, promotion of culture-based fisheries and improvement in fisher education are recommended topics for sustainable fisheries in the reservoir. Rev. Biol. Trop. 59 (4: 1685-1696. Epub 2011 December 01.La laguna Kpong se convirtió en la segunda

  19. Simulated effects of existing and proposed surface-water impoundments and gas-well pads on streamflow and suspended sediment in the Cypress Creek watershed, Arkansas

    Science.gov (United States)

    Hart, Rheannon M.

    2014-01-01

    Cypress Creek is located in central Arkansas and is the main tributary to Brewer Lake, which serves as the primary water supply for Conway, Arkansas, and the surrounding areas. A model of the Cypress Creek watershed was developed and calibrated in cooperation with Southwestern Energy Company using detailed precipitation, streamflow, and discrete suspended-sediment data collected from 2009 through 2012. These data were used with a Hydrologic Simulation Program—FORTRAN model to address different potential gas-extraction activities within the watershed.

  20. Cooling clothing utilizing water evaporation

    DEFF Research Database (Denmark)

    Sakoi, Tomonori; Tominaga, Naoto; Melikov, Arsen Krikor

    2014-01-01

    We developed cooling clothing that utilizes water evaporation to cool the human body and has a mechanism to control the cooling intensity. Clean water was supplied to the outer surface of the T-shirt of the cooling clothing, and a small fan was used to enhance evaporation on this outer surface...... temperature ranging from 27.4 to 30.7 °C to establish a suitable water supply control method. A water supply control method that prevents water accumulation in the T-shirt and water dribbling was validated; this method is established based on the concept of the water evaporation capacity under the applied...

  1. Assessment of soil and groundwater contamination by potentially toxic and trace elements in an impounded vehicle scrapyard: Case study: Ribeirão Pires, SP, Brazil

    International Nuclear Information System (INIS)

    Lange, Camila Neves

    2018-01-01

    Impounded vehicle scrapyard (IVS) overcrowding is currently a subject of concern in Brazilian scenario. The aim of this study was to assess the total levels of potentially toxic elements (PTEs) and trace elements (TE) in soil and groundwater in an IVS located in the city of Ribeirão Pires. In order to achieve this objective, topsoil, three soil cores and groundwater of three monitoring wells were analyzed. It was verified that the area is mainly affected by three factors: (1) a landfill layer with construction waste; (2) an oily residue from past industrial activities in the area; (3) vehicles parked on topsoil. For the evaluation of the results, statistical techniques, such as multivariate analysis, calculation of pollution, ecological and human health risk index were used. Mass fractions of all PTEs, except Co, Cu, Mo and Zn, were higher than reference values. Hot spots were observed for most elements suggesting vehicular source. The Geoaccumulation Index showed minimal to moderate pollution in soil for most elements, except for As and Ba, which showed higher accumulation than other elements. The enrichment factor pointed to a significant enrichment of As and Pb. Arsenic content in soil may pose a moderate to high potential ecological risk. The results of PTEs and as statistical approaches indicated that As, Ce, Co, Cu, Mn, Nb, Ni, Pb and Zn are mainly from anthropogenic sources. The content of most PTEs in topsoil does not pose a potential human health risk, except Cr content. Groundwater levels for most PTEs were below the drinking water recommendation limits, except Mn and Fe content. (author)

  2. Temporal changes in spatial patterns of submersed macrophytes in two impounded reaches of the Upper Mississippi River, USA, 1998-2009

    Science.gov (United States)

    De Jager, Nathan R.; Yin, Yao

    2011-01-01

    We examined temporal changes in spatial patterns of submersed aquatic macrophytes during a recent three-fold increase in macrophyte abundance and in response to the cumulative effects of management actions (island construction and water level management) and changes in regional environmental conditions (turbidity) in two navigation pools of the Upper Mississippi River, Pool 8 (managed) and Pool 13 (unmanaged). We used cross-correlograms to quantify changes in the degree and range of spatial correlation between submersed macrophytes and depth across the impounded portions of the two pools from 1998-2009. Along with increases in abundance, we observed gradual expansion of submersed macrophytes into deeper water in both pools. However, we detected no temporal change in spatial patterns in Pool 13, where the range of spatial correlation was ~ 1500-2500 m in length in the downriver direction and ~ 500-1000 m in length in the crossriver direction. We initially detected similar ranges of spatial correlation in Pool 8, but over time the range of correlation in the cross river direction increased from ~ 500 m in 1998 to ~ 2000 m by 2009. Thus, the expansion of submersed macrophytes into deeper water areas in Pool 8 appears to have occurred in the cross-river direction and led to increases in patch size and a more symmetrical patch configuration. Hence, very similar temporal changes in submersed macrophyte abundance corresponded with different diffusion dynamics and spatial patterns in the two pools. We hypothesize that management actions altered spatial patterns of depth, water flow and/or wind fetch and led to the differences in spatial patterns reported here.

  3. Sealing layer of fly ashes and sewage sludge and vegetation establishment in treatment of mine tailings impoundments; Flygaska och roetslam som taetskikt vid efterbehandling av sandmagasin med vegetationsetablering

    Energy Technology Data Exchange (ETDEWEB)

    Greger, Maria; Neuschuetz, Clara [Stockholm Univ. (Sweden). Dept. of Botany; Isaksson, Karl-Erik [Boliden Mineral AB (Sweden)

    2006-02-15

    Each year the Swedish mining industry produces 25 Mtonnes of mine tailings that are disposed of in extensive natural impoundments. As this sand, containing more or less sulphide-rich minerals, is penetrated by oxygen and water, it starts weathering resulting in formation of acidic and metal-rich drainage water. To prevent oxygen penetration the mine tailings can be covered with a sealing layer covered with a protective cover that facilitates establishment of vegetation. The aim of this study has been to examine the function of fly ash and sewage sludge in sealing layers at impoundments of pyrite rich mine tailings, and the ability of different plant species, which are suitable for establishment in these areas, to penetrate the sealing layer with their roots and what impact they have on the drainage water. Experiments have been performed in field and greenhouse environment, with sealing layers consisting of fly ash and sewage sludge mixtures, covered with protective covers of sewage sludge or till. Plant establishment has been studied in a survey of naturally established plants at sewage sludge disposal sites close to mining areas, and by sowing and planting of selected plants, for instance fast growing grass species and fibre hemp at the test plots in field and in greenhouse experiments. Large scale application of ashes, sewage sludge and an ash/sludge mixture have been performed in field at three test plots with the size of 0.3-1 ha. Leakage of nutrients and metals from sealing layers has been studied in field and greenhouse tests. In addition, the ability of plant roots to penetrate sealing layers made of different ash/sludge mixtures have been examined in greenhouse experiments. This investigation is a cooperation between Stockholm University and Boliden Mineral AB, and the field experiments have been performed at the mine tailings impoundments at Gillervattnet, Boliden. Other collaborating participants are Skellefteaa Kraft and Munksund, who have produced the

  4. Utility usage forecasting

    Science.gov (United States)

    Hosking, Jonathan R. M.; Natarajan, Ramesh

    2017-08-22

    The computer creates a utility demand forecast model for weather parameters by receiving a plurality of utility parameter values, wherein each received utility parameter value corresponds to a weather parameter value. Determining that a range of weather parameter values lacks a sufficient amount of corresponding received utility parameter values. Determining one or more utility parameter values that corresponds to the range of weather parameter values. Creating a model which correlates the received and the determined utility parameter values with the corresponding weather parameters values.

  5. Entrez Programming Utilities

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Entrez Programming Utilities (E-utilities) are a set of eight server-side programs that provide a stable interface into the Entrez query and database system at...

  6. Proteinase production in Pseudomonas fluorescens ON2 is affected by carbon sources and allows surface-attached but not planktonic cells to utilize protein for growth in lake water

    DEFF Research Database (Denmark)

    Nicolaisen, Mette Haubjerg; Worm, Jakob; Jørgensen, Niels O. G.

    2012-01-01

    -colonies were able to utilize this resource, while planktonic cells were not. Our experiments are the first to experimentally support models predicting that production of extra-cellular enzymes in dilute environments may be a waste of resources, whereas it represents a favorable feeding strategy in organic...

  7. Research Utilization in Rehabilitation.

    Science.gov (United States)

    Rogers, Everett M.

    In terms of its attention to research utilization, vocational rehabilitation today may be where agriculture was in 1913. One reason for this is an inadequate understanding of the process of research utilization. Scattered studies of research utilization have occurred, but suffer from a lack of integration. Among propositions that may be postulated…

  8. Computer aided surface representation

    Energy Technology Data Exchange (ETDEWEB)

    Barnhill, R E

    1987-11-01

    The aims of this research are the creation of new surface forms and the determination of geometric and physical properties of surfaces. The full sweep from constructive mathematics through the implementation of algorithms and the interactive computer graphics display of surfaces is utilized. Both three-dimensional and multi- dimensional surfaces are considered. Particular emphasis is given to the scientific computing solution of Department of Energy problems. The methods that we have developed and that we are proposing to develop allow applications such as: Producing smooth contour maps from measured data, such as weather maps. Modeling the heat distribution inside a furnace from sample measurements. Terrain modeling based on satellite pictures. The investigation of new surface forms includes the topics of triangular interpolants, multivariate interpolation, surfaces defined on surfaces and monotone and/or convex surfaces. The geometric and physical properties considered include contours, the intersection of surfaces, curvatures as a interrogation tool, and numerical integration.

  9. US utility partnerships

    International Nuclear Information System (INIS)

    Worthington, B.

    1995-01-01

    Activities of the United States Energy Association were reviewed, as well as the manner in which its members are benefitting from the Association's programs. The principal cooperative program set up is the Utility Partnership Program, which was described. Through this program the Association is matching US companies, both electric utilities and gas utilities, with counterparts in Eastern Europe or the former Soviet Union. So far, about 25 partnerships were signed, e.g. in the Czech Republic, in Kazakhstan, in Poland, and in Slovakia. It was estimated that the return to the United States from the investments made by the American government in these Utility Partnership Programs has been well over 100-fold

  10. Test surfaces useful for calibration of surface profilometers

    Science.gov (United States)

    Yashchuk, Valeriy V; McKinney, Wayne R; Takacs, Peter Z

    2013-12-31

    The present invention provides for test surfaces and methods for calibration of surface profilometers, including interferometric and atomic force microscopes. Calibration is performed using a specially designed test surface, or the Binary Pseudo-random (BPR) grating (array). Utilizing the BPR grating (array) to measure the power spectral density (PSD) spectrum, the profilometer is calibrated by determining the instrumental modulation transfer.

  11. Utility portfolio diversification

    International Nuclear Information System (INIS)

    Griffes, P.H.

    1990-01-01

    This paper discusses portfolio analysis as a method to evaluate utility supply decisions. Specifically a utility is assumed to increase the value of its portfolio of assets whenever it invests in a new supply technology. This increase in value occurs because the new asset either enhances the return or diversifies the risks of the firm's portfolio of assets. This evaluation method is applied to two supply innovations in the electric utility industry: jointly-owned generating plants and supply contracts with independent power producers (IPPs)

  12. Depletion of barium and radium-226 in Black Sea surface waters over the past thirty years

    International Nuclear Information System (INIS)

    Kenison Falkner, K.K.; Edmond, J.M.; O'Neill, D.J.; Todd, J.F.; Moore, W.S.

    1991-01-01

    The nearly landlocked waters of the Black Sea support a valuable fishery, but are also particularly vulnerable to anthropogenic disturbance. Here we use dissolved barium and radium-226 as tracers, to investigate the biogeochemical health of the sea. Both elements are brought to surface waters by vertical mixing of deeper, enriched waters, and by rivers; these inputs should ordinarily be balanced by outflow of surface waters at the Bosphorus, and by biologically mediated removal of 226 Ra-bearing barite. We show, however, that surface-water inventories have been substantially depleted over the past few decades: recent (1988-89) barium concentrations were 1.6 times lower than in 1958 and 1967. These observations suggest that steady-state cycling of these elements has been perturbed by increased primary productivity, presumably fuelled by nutrients from industry and agricultural runoff, and to a lesser extent by decreased fluvial sediment loads owing to extensive impoundment of rivers in the region. (author)

  13. MSIS Drug Utilization Datamart

    Data.gov (United States)

    U.S. Department of Health & Human Services — This page provides background needed to take advantage of the capabilities of the MSIS Drug Utilization Datamart. This mart allows the user to develop high-level...

  14. Chemical Search Web Utility

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Chemical Search Web Utility is an intuitive web application that allows the public to easily find the chemical that they are interested in using, and which...

  15. Utility requirements for HTGRs

    International Nuclear Information System (INIS)

    Nicholls, D.R.

    1997-01-01

    Eskom, the state utility of South Africa, is currently evaluating the technical and economic feasibility of the helium cooled Pebble Bed Modular Reactor with a closed cycle gas turbine power conversion system for future power generating additions to its electric system. This paper provides an overview of the Eskom system including the needs of the utility for future generation capacity and the key performance requirements necessary for incorporation of this gas cooled reactor plant. (author)

  16. Utility requirements for fusion

    International Nuclear Information System (INIS)

    Vondrasek, R.J.

    1982-02-01

    This report describes work done and results obtained during performance of Task 1 of a study of Utility Requirements and Criteria for Fusion Options. The work consisted of developing a list of utility requirements for fusion optics containing definition of the requirements and showing their relative importance to the utility industry. The project team members developed a preliminary list which was refined by discussions and literature searches. The refined list was recast as a questionnaire which was sent to a substantial portion of the utility industry in this country. Forty-three questionnaire recipients responded including thirty-two utilities. A workshop was held to develop a revised requirements list using the survey responses as a major input. The list prepared by the workshop was further refined by a panel consisting of vice presidents of the three project team firms. The results of the study indicate that in addition to considering the cost of energy for a power plant, utilities consider twenty-three other requirements. Four of the requirements were judged to be vital to plant acceptability: Plant Capital Cost, Financial Liability, Plant Safety and Licensability

  17. Quantitative Hydrocarbon Surface Analysis

    Science.gov (United States)

    Douglas, Vonnie M.

    2000-01-01

    The elimination of ozone depleting substances, such as carbon tetrachloride, has resulted in the use of new analytical techniques for cleanliness verification and contamination sampling. The last remaining application at Rocketdyne which required a replacement technique was the quantitative analysis of hydrocarbons by infrared spectrometry. This application, which previously utilized carbon tetrachloride, was successfully modified using the SOC-400, a compact portable FTIR manufactured by Surface Optics Corporation. This instrument can quantitatively measure and identify hydrocarbons from solvent flush of hardware as well as directly analyze the surface of metallic components without the use of ozone depleting chemicals. Several sampling accessories are utilized to perform analysis for various applications.

  18. Utility planning for decommissioning

    International Nuclear Information System (INIS)

    Williams, D.H.

    1982-01-01

    Though the biggest impact on a utility of nuclear power plant decommissioning may occur many years from now, procrastination of efforts to be prepared for that time is unwarranted. Foresight put into action through planning can significantly affect that impact. Financial planning can assure the recovery of decommissioning costs in a manner equitable to customers. Decision-making planning can minimize adverse affects of current decisions on later decommissioning impacts and prepare a utility to be equipped to make later decommissioning decisions. Technological knowledge base planning can support all other planning aspects for decommissioning and prepare a utility for decommissioning decisions. Informed project planning can ward off potentially significant pitfalls during decommissioning and optimize the effectiveness of the actual decommissioning efforts

  19. Electric utility report '80

    International Nuclear Information System (INIS)

    Anon.

    1980-01-01

    A collection of brief atricles describes the trends and developments in Canada's electric utilities for the 1980's. Generating stations planned or under construction are listed. The trends in technology discused at a recent Canadian Electrical Association meeting are summarized in such areas as turbine stability control, power line vibration control, system reliability, substations and transformer specifications. Developments in nuclear generation are discussed and compared on the world scale where Japan, for example, has the world's largest nuclear program. Progress on fusion is discussed. In Canada the electric utilities are receiving the support of the comprehensive nuclear R and D program of Atomic Energy of Canada Ltd. New innovations in utility technology such as street lighting contactors, superconductive fault limiters and demand profile analyzers are discussed. (T.I.)

  20. Underground coal mine subsidence impacts on surface water

    International Nuclear Information System (INIS)

    Stump, D.E. Jr.

    1992-01-01

    This paper reports that subsidence from underground coal mining alters surface water discharge and availability. The magnitude and areal extent of these impacts are dependent on many factors, including the amount of subsidence, topography, geology, climate, surface water - ground water interactions, and fractures in the overburden. There alterations may have positive and/or negative impacts. One of the most significant surface water impacts occurred in July 1957 near West Pittston, Pennsylvania. Subsidence in the Knox Mine under the Coxton Yards of the Lehigh Valley Railroad allowed part of the discharge in the Susquehanna River to flow into the mine and create a crater 200 feet in diameter and 300 feet deep. Fourteen railroad gondola cars fell into the hole which was eventually filled with rock, sand, and gravel. Other surface water impacts from subsidence may include the loss of water to the ground water system, the gaining of water from the ground water system, the creation of flooded subsidence troughs, the increasing of impoundment storage capacity, the relocation of water sources (springs), and the alteration of surface drainage patterns

  1. Health care utilization

    DEFF Research Database (Denmark)

    Jacobsen, Christian Bøtcher; Andersen, Lotte Bøgh; Serritzlew, Søren

    An important task in governing health services is to control costs. The literatures on both costcontainment and supplier induced demand focus on the effects of economic incentives on health care costs, but insights from these literatures have never been integrated. This paper asks how economic cost...... containment measures affect the utilization of health services, and how these measures interact with the number of patients per provider. Based on very valid register data, this is investigated for 9.556 Danish physiotherapists between 2001 and 2008. We find that higher (relative) fees for a given service...... are important, but that economics cannot alone explain the differences in health care utilization....

  2. Energy conversion and utilization technologies

    International Nuclear Information System (INIS)

    1988-01-01

    The DOE Energy Conversion and Utilization Technologies (ECUT) Program continues its efforts to expand the generic knowledge base in emerging technological areas that support energy conservation initiatives by both the DOE end-use sector programs and US private industry. ECUT addresses specific problems associated with the efficiency limits and capabilities to use alternative fuels in energy conversion and end-use. Research is aimed at understanding and improving techniques, processes, and materials that push the thermodynamic efficiency of energy conversion and usage beyond the state of the art. Research programs cover the following areas: combustion, thermal sciences, materials, catalysis and biocatalysis, and tribology. Six sections describe the status of direct contact heat exchange; the ECUT biocatalysis project; a computerized tribology information system; ceramic surface modification; simulation of internal combustion engine processes; and materials-by-design. These six sections have been indexed separately for inclusion on the database. (CK)

  3. Electric utilities in Illinois

    Energy Technology Data Exchange (ETDEWEB)

    1978-01-01

    Although the conference dealt specifically with concerns of the electric utilities in Illinois, the issues were dealt with in the national context as well. A separate abstract was prepared for each of the 5 sections of this proceeding. A total of 25 papers were presented. Section titles are: Forecasting, Planning and Siting, Reliability, Rates and Financing, and Future Developments.

  4. Male Adolescent Contraceptive Utilization.

    Science.gov (United States)

    Finkel, Madelon Lubin; Finkel, David J.

    1978-01-01

    The contraceptive utilization of a sample of sexually active, urban, high school males (Black, Hispanic, and White) was examined by anonymous questionnaire. Contraceptive use was haphazard, but White males tended to be more effective contraceptors than the other two groups. Reasons for nonuse were also studied. (Author/SJL)

  5. Nontransferable Utility Bankruptcy Games

    NARCIS (Netherlands)

    Estevez, A.; Borm, P.E.M.; Fiestras-Janeiro, G.

    2014-01-01

    In this paper, we analyze bankruptcy problems with nontransferable utility (NTU) from a game theoretical perspective by redefining corresponding NTU-bankruptcy games in a tailor-made way. It is shown that NTU-bankruptcy games are both coalitional merge convex and ordinal convex. Generalizing the

  6. DNA ELECTROPHORESIS AT SURFACES

    Energy Technology Data Exchange (ETDEWEB)

    RAFAILOVICH, MIRIAM; SOKOLOV, JONATHAN; GERSAPPE, DILIP

    2003-09-01

    During this year we performed two major projects: I. We developed a detailed theoretical model which complements our experiments on surface DNA electrophoresis. We found that it was possible to enhance the separation of DNA chains by imposing a chemical nanoscale pattern on the surface. This approach utilized the surface interaction effect of the DNA chains with the substrate and is a refinement to our previous method in which DNA chains were separated on homogeneous flat surfaces. By introducing the nano-patterns on the surface, the conformational changes of DNA chains of different lengths can be amplified, which results in the different friction strengths with the substrate surface. Our results also show that, when compared to the DNA electrophoresis performed on homogeneous flat surfaces, nanopatterned surfaces offer a larger window in choosing different surface interactions to achieve separation. II. In collaboration with a large international manufacturer of skin care products we also embarked on a project involving photo toxicity of titanium dioxide nanoparticles, which are a key ingredient in sunscreen and cosmetic lotions. The results clearly implicated the nanoparticles in catalyzing damage to chromosomal DNA. We then used this knowledge to develop a polymer/anti-oxidant coating which prevented the photocatalytic reaction on DNA while still retaining the UV absorptive properties of the nanoparticles. The standard gel electrophoresis was not sufficient in determining the extent of the DNA damage. The conclusions of this study were based predominantly on analysis obtained with the surface electrophoresis method.

  7. Biomass ash utilization

    Energy Technology Data Exchange (ETDEWEB)

    Bristol, D.R.; Noel, D.J.; O`Brien, B. [HYDRA-CO Operations, Inc., Syracuse, NY (United States); Parker, B. [US Energy Corp., Fort Fairfield, ME (United States)

    1993-12-31

    This paper demonstrates that with careful analysis of ash from multiple biomass and waste wood fired power plants that most of the ash can serve a useful purpose. Some applications require higher levels of consistency than others. Examples of ash spreading for agricultural purposes as a lime supplement for soil enhancement in Maine and North Carolina, as well as a roadbase material in Maine are discussed. Use of ash as a horticultural additive is explored, as well as in composting as a filtering media and as cover material for landfills. The ash utilization is evaluated in a framework of environmental responsibility, regulations, handling and cost. Depending on the chemical and physical properties of the biomass derived fly ash and bottom ash, it can be used in one or more applications. Developing a program that utilizes ash produced in biomass facilities is environmentally and socially sound and can be financially attractive.

  8. Industrial coal utilization

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-01-01

    The effects of the National Energy Act on the use of coal in US industrial and utility power plants are considered. Innovative methods of using coal in an environmentally acceptable way are discussed: furnace types, fluidized-bed combustion, coal-oil-mixtures, coal firing in kilns and combustion of synthetic gas and liquid fuels. Fuel use in various industries is discussed with trends brought about by uncertain availability and price of natural gas and fuel oils: steel, chemical, cement, pulp and paper, glass and bricks. The symposium on Industrial Coal Utilization was sponsored by the US DOE, Pittsburgh Energy Technology Center, April 3 to 4, 1979. Twenty-one papers have been entered individually into the EDB. (LTN)

  9. Utilization of research reactors

    International Nuclear Information System (INIS)

    1962-01-01

    About 200 research reactors are now in operation in different parts of the world, and at least 70 such facilities, which are in advanced stages of planning and construction, should be critical within the next two or three years. In the process of this development a multitude of problems are being encountered in formulating and carrying out programs for the proper utilization of these facilities, especially in countries which have just begun or are starting their atomic energy work. An opportunity for scientific personnel from different Member States to discuss research reactor problems was given at an international symposium on the Programing and Utilization of Research Reactors organized by the Agency almost immediately after the General Conference session. Two hundred scientists from 35 countries, as well as from the European Nuclear Energy Agency and EURATOM, attended the meeting which was held in Vienna from 16 to 21 October 1961

  10. Utility customer issues

    International Nuclear Information System (INIS)

    Downey, W.H.

    1997-01-01

    Customer issues affected by the restructuring of the $250 billion US electric power industry were discussed. In the past the industry's vertically integrated utilities conducted their business in protected geographic markets. With deregulation and greater competition, that industry structure will change. This presentation highlighted the strategies that Unicom is using to react to the restructuring of the electric power industry. The underlying principle is for the utility to reinvent itself to change its market orientation and focus on customer services, such as reliability, responsiveness, custom tailored solutions, and guaranteed savings over time. Attempting to become total energy providers and delivering integrated solutions to meet the needs of large industrial and commercial consumers, intensive market research, improved service and installation, and sophisticated customer retention initiatives will also have to be high on the agenda

  11. UTILITY OF SIMPLIFIED LABANOTATION

    Directory of Open Access Journals (Sweden)

    Maria del Pilar Naranjo

    2016-02-01

    Full Text Available After using simplified Labanotation as a didactic tool for some years, the author can conclude that it accomplishes at least three main functions: efficiency of rehearsing time, social recognition and broadening of the choreographic consciousness of the dancer. The doubts of the dancing community about the issue of ‘to write or not to write’ are highly determined by the contexts and their own choreographic evolution, but the utility of Labanotation, as a tool for knowledge, is undeniable.

  12. NASA's Technology Utilization Program.

    Science.gov (United States)

    Farley, C. F.

    1972-01-01

    NASA's Technology Utilization Program is described, illustrating how it can be useful in achieving improved productivity, providing more jobs, solving public sector challenges, and strengthening the international competitive situation. Underlying the program is the fact that research and development conducted in NASA's aeronautics and space programs have generated much technical information concerning processes, products, or techniques which may be useful to engineers, doctors, or to others. The program is based on acquisition and publication, working with the user, and applications engineering.

  13. Debating Clinical Utility

    OpenAIRE

    Burke, W.; Laberge, A.-M.; Press, N.

    2010-01-01

    The clinical utility of genetic tests is determined by the outcomes following test use. Like other measures of value, it is often contested. Stakeholders may have different views about benefits and risks and about the importance of social versus health outcomes. They also commonly disagree about the evidence needed to determine whether a test is effective in achieving a specific outcome. Questions may be presented as factual disagreements, when they are actually debates about what information...

  14. Role of the utility

    International Nuclear Information System (INIS)

    Bellin, A.

    1986-03-01

    It is common to say that a nuclear programme needs basic infrastructures such as an appropriate educational system, governmental organizations for regulation, decision and inspection, engineering organizations for design and implementation, industrial infrastructures for manufacturing, erection and commissioning, operation organizations for running and maintaining power plants. This schematic organization is not sufficient to succeed in a nuclear programme: one has to consider very carefully the attribution of responsibilities. It appears, that, among all the different systems which exist in the world for the organization of a nuclear project, it is always the utility which bears the overall responsibility for the implementation of the project. It defines objectives such as production capacity, schedule, price; it takes part in the definition of a national policy for energy supply, for the choice of a type of reactor, for the implementation of a national nuclear industry; it selects sites and conducts feasibility studies including a preliminary project; it participates in the definition of organization charts and selects contractors; it calls for and obtains authorizations from regulatory bodies; it manages the project, coordinates contractors and permanently ensures that goals are attained as regards safety, quality, schedule, costs. The French utility has directly taken charge of all these basic responsibilities and this is commonly considered as a major reason of the success of the French nuclear programme. Depending on its capacities, the utility may delegate some of these responsibilities - mainly concerning engineering and project management - to experienced firms. Nevertheless, one has to remember that the utility bears the final responsibility and that it is probably the organization most fully aware of the fact that the final goal is not the construction of a nuclear power station but the production of nuclear electricity in the best and safest conditions

  15. Electric utilities in 2007

    Energy Technology Data Exchange (ETDEWEB)

    Hyman, L.S. [Smith Barney Inc., New York, NY (United States)

    1998-10-01

    A century ago--in the year J.J. Thomson discovered the electron--electricity, gas and traction companies battled for markets, and corrupt city councils demanded their fair share of the take. One tycoon became so disgusted with the confusion and dishonesty that he decided to bribe the legislature to set up an honest, state-run regulatory agency that would bring order to chaos. But he was found out. The scandal set back the cause of regulation until 1907, the year in which the electric washing machine and the vacuum cleaner were invented. By then, electricity sales had septupled from 1897 levels, and three states had established utility regulation. In the coming decade, 1997 to 2007, the utility business could undergo similar dramatic change, but it will move toward less regulation and more competition during a period of slow growth. Management will have to work harder to achieve success, however, because much of the profits will have to come not from a growing market but from the pockets of competitors. By 2007, electricity will constitute a component of a larger energy and utility services industry that sells electricity, natural gas and possibly water, propane and telecommunications. Customized service will meet the needs of consumers of all sizes. The dominant firm in the industry, the virtual utility, may look more like a financial organization or a mass marketer than the traditional converter of raw material to energy. Emphasis on market-based pricing should lead to more efficient use of resources. If the process works right, the consumer wins.

  16. Clean energy utilization technology

    International Nuclear Information System (INIS)

    Honma, Takuya

    1992-01-01

    The technical development of clean energy including the utilization of solar energy was begun in 1973 at the time of the oil crisis, and about 20 years elapsed. Also in Japan, the electric power buying system by electric power companies for solar light electric power and wind electric power has been started in 1992, namely their value as a merchandise was recognized. As for these two technologies, the works of making the international standards and JIS were begun. The range of clean energy or natural energy is wide, and its kinds are many. The utilization of solar heat and the electric power generation utilizing waves, tide and geotherm already reached the stage of practical use. Generally in order to practically use new energy, the problem of price must be solved, but the price is largely dependent on the degree of spread. Also the reliability, durability and safety must be ensured, and the easiness of use, effectiveness and trouble-saving maintenance and operation are required. For the purpose, it is important to packaging those skillfully in a system. The cases of intelligent natural energy systems are shown. Solar light and wind electric power generation systems and the technology of transporting clean energy are described. (K.I.)

  17. Market research for electric utilities

    International Nuclear Information System (INIS)

    Shippee, G.

    1999-01-01

    Marketing research is increasing in importance as utilities become more marketing oriented. Marketing research managers need to maintain autonomy from the marketing director or ad agency and make sure their work is relevant to the utility's operation. This article will outline a model marketing research program for an electric utility. While a utility may not conduct each and every type of research described, the programs presented offer a smorgasbord of activities which successful electric utility marketers often use or have access to

  18. Utilization of solar energy in cold climate

    OpenAIRE

    Tazeeva, Elena

    2010-01-01

    Solar radiation is a source of life on the Earth. The sun heats the atmosphere and the surface of our planet. Because of the sun winds are blowing, circulation of water is happened, seas and oceans are heated, and plants are growing. Nowadays people know how to transfer solar radiation straightly into energy. The subject of the project is to research the possibilities of utilization of solar energy in cold climate. At this project the model of calculation solar energy is shown. Following ...

  19. Time Functions as Utilities

    Science.gov (United States)

    Minguzzi, E.

    2010-09-01

    Every time function on spacetime gives a (continuous) total preordering of the spacetime events which respects the notion of causal precedence. The problem of the existence of a (semi-)time function on spacetime and the problem of recovering the causal structure starting from the set of time functions are studied. It is pointed out that these problems have an analog in the field of microeconomics known as utility theory. In a chronological spacetime the semi-time functions correspond to the utilities for the chronological relation, while in a K-causal (stably causal) spacetime the time functions correspond to the utilities for the K + relation (Seifert’s relation). By exploiting this analogy, we are able to import some mathematical results, most notably Peleg’s and Levin’s theorems, to the spacetime framework. As a consequence, we prove that a K-causal (i.e. stably causal) spacetime admits a time function and that the time or temporal functions can be used to recover the K + (or Seifert) relation which indeed turns out to be the intersection of the time or temporal orderings. This result tells us in which circumstances it is possible to recover the chronological or causal relation starting from the set of time or temporal functions allowed by the spacetime. Moreover, it is proved that a chronological spacetime in which the closure of the causal relation is transitive (for instance a reflective spacetime) admits a semi-time function. Along the way a new proof avoiding smoothing techniques is given that the existence of a time function implies stable causality, and a new short proof of the equivalence between K-causality and stable causality is given which takes advantage of Levin’s theorem and smoothing techniques.

  20. Social group utility maximization

    CERN Document Server

    Gong, Xiaowen; Yang, Lei; Zhang, Junshan

    2014-01-01

    This SpringerBrief explains how to leverage mobile users' social relationships to improve the interactions of mobile devices in mobile networks. It develops a social group utility maximization (SGUM) framework that captures diverse social ties of mobile users and diverse physical coupling of mobile devices. Key topics include random access control, power control, spectrum access, and location privacy.This brief also investigates SGUM-based power control game and random access control game, for which it establishes the socially-aware Nash equilibrium (SNE). It then examines the critical SGUM-b

  1. Energy utilization in Canada

    International Nuclear Information System (INIS)

    Klassen, J.

    1976-04-01

    The situation of the energy supply of Canada is characterized by its geographic location and by the dispersal of the energy consumers over a wide area. At present, the energy supply leaving the successful CANDU nuclear energy programme out of account, is based mainly on crude oil, natural gas, and electricity as well as on coal imported from the USA. The targets of Canadian enery policies and energy research are stated as follows: a) Reducing and optimizing energy consumption, b) introducing district heating, and c) utilizing the extensive local coal deposits. (GG) [de

  2. Managing the nuclear utility

    International Nuclear Information System (INIS)

    Williams, J.W. Jr.

    1985-01-01

    The Florida Power and Light Company (FP and L) is the fifth largest investor-owned utility in the country. The success of nuclear power generation at the St. Lucie Units 1 and 2 and Turkey Point Units 3 and 4 has resulted from a continuing management commitment to the nuclear program. The management of the power plants rely strongly on teamwork for most large projects and activities whether they entail plant operation, construction, or maintenance. Various examples of how teamwork has been used to realize the successful completion of projects or solutions to problems are given

  3. Tribal Utility Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Engel, R. A.; Zoellick, J. J.

    2007-06-30

    The Schatz Energy Research Center (SERC) assisted the Yurok Tribe in investigating the feasibility of creating a permanent energy services program for the Tribe. The original purpose of the DOE grant that funded this project was to determine the feasibility of creating a full-blown Yurok Tribal electric utility to buy and sell electric power and own and maintain all electric power infrastructure on the Reservation. The original project consultant found this opportunity to be infeasible for the Tribe. When SERC took over as project consultant, we took a different approach. We explored opportunities for the Tribe to develop its own renewable energy resources for use on the Reservation and/or off-Reservation sales as a means of generating revenue for the Tribe. We also looked at ways the Tribe can provide energy services to its members and how to fund such efforts. We identified opportunities for the development of renewable energy resources and energy services on the Yurok Reservation that fall into five basic categories: • Demand-side management – This refers to efforts to reduce energy use through energy efficiency and conservation measures. • Off-grid, facility and household scale renewable energy systems – These systems can provide electricity to individual homes and Tribal facilities in areas of the Reservation that do not currently have access to the electric utility grid. • Village scale, micro-grid renewable energy systems - These are larger scale systems that can provide electricity to interconnected groups of homes and Tribal facilities in areas of the Reservation that do not have access to the conventional electric grid. This will require the development of miniature electric grids to serve these interconnected facilities. • Medium to large scale renewable energy development for sale to the grid – In areas where viable renewable energy resources exist and there is access to the conventional electric utility grid, these resources can be

  4. New design of material surface utilizing introduction of hydroxyl

    International Nuclear Information System (INIS)

    Kim, Min; Tsuneda, Satoshi; Saito, Kyoichi

    1994-01-01

    In order to give new function to the polymer materials having various shapes which are easily available, for example films, unwoven cloths, tubes and hollow threads, while maintaining the shapes, graft polymerization is suitable. The common procedure for graft poly merization is first a radical is formed in an original polymer, then vinyl monomer is brought in contact with there, and it is converted to the desired functional radical. The research group of the authors developed the new film material which can separate and refine rapidly and in large capacity protein from culture solution and blood plasma, and proposed the new technique for synthesizing the ion exchange material having the shape suitable to use more simply. In both cases, the graft polymer chain having hydroxyl plays the important role. By extending graft polymer chain from the circumferences of holes in a porous film toward the holes and passing protein solution through it, protein is recovered. The method of making such porous films and the method of introducing hydroxyl are explained. When the vinyl monomer having sulfonic acid radical is given to polyethylene films and tubes, the films change to ion exchange films, and the tubes change to acid catalyst. These processes are explained. (K.I.)

  5. Autonomous Utility Connector for Lunar Surface Systems, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Lunar dust has been identified as a significant and present challenge in future exploration missions. Significant development is called for in the area of devices...

  6. Color changing plasmonic surfaces utilizing liquid crystal (Conference Presentation)

    Science.gov (United States)

    Franklin, Daniel; Wu, Shin-Tson; Chanda, Debashis

    2016-09-01

    Plasmonic structural color has recently garnered significant interest as an alternative to the organic dyes standard in print media and liquid crystal displays. These nanostructured metallic systems can produce diffraction limited images, be made polarization dependent, and exhibit resistance to color bleaching. Perhaps even more advantageous, their optical characteristics can also be tuned, post-fabrication, by altering the surrounding media's refractive index parallel to the local plasmonic fields. A common material with which to achieve this is liquid crystal. By reorienting the liquid crystal molecules through external electric fields, the optical resonances of the plasmonic filters can be dynamically controlled. Demonstrations of this phenomenon, however, have been limited to modest shifts in plasmon resonance. Here, we report a liquid crystal-plasmonic system with an enhanced tuning range through the use of a shallow array of nano-wells and high birefringent liquid crystal. The continuous metallic nanostructure maximizes the overlap between plasmonic fields and liquid crystal while also allowing full reorientation of the liquid crystal upon an applied electric field. Sweeping over structural dimensions and voltages results in a color palette for these dynamic reflective pixels that can further be exploited to create color tunable images. These advances make plasmonic-liquid crystal systems more attractive candidates for filter, display, and other tunable optical technologies.

  7. Autonomous Utility Connector for Lunar Surface Systems, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Lunar dust has been identified as a significant and present challenge in future exploration missions. The interlocking, angular nature of Lunar dust and its broad...

  8. Geothermal Resource Utilization

    Energy Technology Data Exchange (ETDEWEB)

    Lienau, Paul J.

    1998-01-03

    Man has utilized the natural heat of the earth for centuries. Worldwide direct use of geothermal currently amounts to about 7,000 MWt, as compared to 1,500 MWe, now being used for the generation of electricity. Since the early 1970s, dwindling domestic reservoirs of oil and gas, continued price escalation of oil on the world market and environmental concerns associated with coal and nuclear energy have created a growing interest in the use of geothermal energy in the United States. The Department of Energy goals for hydrothermal resources utilization in the United States, expressed in barrels of oil equivalent, is 50 to 90 million bbl/yr by 1985 and 350 to 900 million bbl/yr by the year 2000. This relatively clean and highly versatile resource is now being used in a multitude of diverse applications (e.g., space heating and cooling, vegetable dehydration, agriculture, aquaculture, light manufacturing), and other applications requiring a reliable and economic source of heat.

  9. Utilization of coalbed methane

    Energy Technology Data Exchange (ETDEWEB)

    Gustavson, J.B. [Gustavson Associates Inc., Boulder, CO (United States)

    1996-02-01

    Substantial progress has been made in capturing coalbed methane (CBM gas), which constitutes a valuable source of clean burning energy. It is of importance to study the various potential uses of coalbed methane and to understand the various technologies required, as well as their economics and any institutional constraints. In industrialised countries, the uses of coalbed methane are almost solely dependent on microeconomics; coalbed methane must compete for a market against natural gas and other energy sources - and frequently, coalbed methane is not competitive against other energy sources. In developing countries, on the other hand, particularly where other sources of energy are in short supply, coalbed methane economics yield positive results. Here, constraints to development of CBM utilization are mainly lack of technology and investment capital. Sociological aspects such as attitude and cultural habits, may also have a strong negative influence. This paper outlines the economics of coalbed methane utilization, particularly its competition with natural gas, and touches upon the many different uses to which coalbed methane may be applied. 24 refs., 4 figs.

  10. 1994 Panel 1 Utilization Plan

    International Nuclear Information System (INIS)

    1994-01-01

    The Waste Isolation Pilot Plant (WIPP) is intended to receive, handle, and permanently dispose of transuranic (TRU) waste. To fulfill this mission, the U.S. Department of Energy (DOE) constructed a full-scale facility to demonstrate both technical and operational principles of the permanent isolation of TRU waste. The WIPP consists of surface and underground facilities. Panel 1 is situated in the underground facility horizon which is located approximately 2,150 feet below the surface in the predominantly halite Salado Formation. The Panel 1 Utilization Plan provides a strategy for the optimum use of Panel 1 which is consistent with the priorities established by the DOE to accomplish the WIPP mission. These priorities, which include maintaining personnel safety, conducting performance assessment, and continued operational enhancements, are the guiding premise for the decisions on the planned usage of the WIPP underground facility. The continuation of ongoing investigations along with the planned testing and training to be carried out in Panel 1 will enhance the current knowledge and understanding of the operational and geotechnical aspects of the panel configuration. This enhancement will ultimately lead to safer, more efficient, and more cost-effective methods of operation. Excavation of the waste storage area began in May 1986 with the mining of entries to Panel 1. The original design for the waste storage rooms at the WIPP provided a limited period of time during which to mine the openings and to emplace waste. Each panel, consisting of seven storage rooms, was scheduled to be mined and filled in less than 5 years. Panel 1 was developed to receive waste for a demonstration phase that was scheduled to start in October 1988. The demonstration phase was deferred, and the experimental test program was modified to use contact-handled (CH) transuranic waste in bin-scale tests, planned for Room 1, Panel 1

  11. Utilities in UNIX

    International Nuclear Information System (INIS)

    Perez, L.

    2002-01-01

    This manual goes to the users with some or much experience in the unix operating system. In such manner that they can get more efficiency using the unix of the most vendors. Include the majority of UNIX commands, shell built-in functions to create scripts, and a brief explication of the variables in several environments. In addition, other products are included, more and more integrated in the most of the unix operating systems. For example: the scanning and processing language awk, the print server LPRng, GNU Utilities, batch subsystem, etc. The manual was initially based in an specific unix. But it and been written for use of the most unix that exist: Tru64 unix, aix, iris, hpux. solaris y linux. In this way, many examples in the chapter had been included. The purpose of this manual is to provide an UNIX reference for advanced users in any of the unix operating systems family. (Author)

  12. Energy utilities and the Internet

    International Nuclear Information System (INIS)

    2000-01-01

    The chances for energy utilities in the Netherlands to present themselves on the Internet are briefly outlined. It appears that other businesses are ahead of the Dutch utilities in offering electronic services with respect to energy

  13. Minimal surfaces

    CERN Document Server

    Dierkes, Ulrich; Sauvigny, Friedrich; Jakob, Ruben; Kuster, Albrecht

    2010-01-01

    Minimal Surfaces is the first volume of a three volume treatise on minimal surfaces (Grundlehren Nr. 339-341). Each volume can be read and studied independently of the others. The central theme is boundary value problems for minimal surfaces. The treatise is a substantially revised and extended version of the monograph Minimal Surfaces I, II (Grundlehren Nr. 295 & 296). The first volume begins with an exposition of basic ideas of the theory of surfaces in three-dimensional Euclidean space, followed by an introduction of minimal surfaces as stationary points of area, or equivalently

  14. YEAR 2 BIOMASS UTILIZATION

    Energy Technology Data Exchange (ETDEWEB)

    Christopher J. Zygarlicke

    2004-11-01

    This Energy & Environmental Research Center (EERC) Year 2 Biomass Utilization Final Technical Report summarizes multiple projects in biopower or bioenergy, transportation biofuels, and bioproducts. A prototype of a novel advanced power system, termed the high-temperature air furnace (HITAF), was tested for performance while converting biomass and coal blends to energy. Three biomass fuels--wood residue or hog fuel, corn stover, and switchgrass--and Wyoming subbituminous coal were acquired for combustion tests in the 3-million-Btu/hr system. Blend levels were 20% biomass--80% coal on a heat basis. Hog fuel was prepared for the upcoming combustion test by air-drying and processing through a hammer mill and screen. A K-Tron biomass feeder capable of operating in both gravimetric and volumetric modes was selected as the HITAF feed system. Two oxide dispersion-strengthened (ODS) alloys that would be used in the HITAF high-temperature heat exchanger were tested for slag corrosion rates. An alumina layer formed on one particular alloy, which was more corrosion-resistant than a chromia layer that formed on the other alloy. Research activities were completed in the development of an atmospheric pressure, fluidized-bed pyrolysis-type system called the controlled spontaneous reactor (CSR), which is used to process and condition biomass. Tree trimmings were physically and chemically altered by the CSR process, resulting in a fuel that was very suitable for feeding into a coal combustion or gasification system with little or no feed system modifications required. Experimental procedures were successful for producing hydrogen from biomass using the bacteria Thermotoga, a deep-ocean thermal vent organism. Analytical procedures for hydrogen were evaluated, a gas chromatography (GC) method was derived for measuring hydrogen yields, and adaptation culturing and protocols for mutagenesis were initiated to better develop strains that can use biomass cellulose. Fly ash derived from

  15. Rumble surfaces

    CSIR Research Space (South Africa)

    National Institute for Transport and Road

    1977-01-01

    Full Text Available Rumble surfaces are intermittent short lengths of coarse-textured road surfacings on which vehicle tyres produce a rumbling sound. used in conjunction with appropriate roadsigns and markings, they can reduce accidents on rural roads by alerting...

  16. Utilization management in anatomic pathology.

    Science.gov (United States)

    Lewandrowski, Kent; Black-Schaffer, Steven

    2014-01-01

    There is relatively little published literature concerning utilization management in anatomic pathology. Nonetheless there are many utilization management opportunities that currently exist and are well recognized. Some of these impact only the cost structure within the pathology department itself whereas others reduce charges for third party payers. Utilization management may result in medical legal liabilities for breaching the standard of care. For this reason it will be important for pathology professional societies to develop national utilization guidelines to assist individual practices in implementing a medically sound approach to utilization management. © 2013.

  17. Utility service entrance in boreholes

    International Nuclear Information System (INIS)

    1987-08-01

    This study evaluates alternatives for utility service entrances to the repository. We determined the requirements for a repository utility supply. These requirements were defined as safety, maintainability, flexibility, reliability, cost efficiency, voltage regulation, and simplicity of operation. The study showed that repository shafts can best satisfy all requirements for location of the utility supply without the use of borehole penetrations into the repository. It is recommended that the shafts be utilized for utility distribution to the repository, and that the current NWTS program position to minimize the number of boreholes penetrating the repository horizon be maintained. 42 refs., 2 figs., 3 tabs

  18. National Utility Rate Database: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Ong, S.; McKeel, R.

    2012-08-01

    When modeling solar energy technologies and other distributed energy systems, using high-quality expansive electricity rates is essential. The National Renewable Energy Laboratory (NREL) developed a utility rate platform for entering, storing, updating, and accessing a large collection of utility rates from around the United States. This utility rate platform lives on the Open Energy Information (OpenEI) website, OpenEI.org, allowing the data to be programmatically accessed from a web browser, using an application programming interface (API). The semantic-based utility rate platform currently has record of 1,885 utility rates and covers over 85% of the electricity consumption in the United States.

  19. Surface thermodynamics

    International Nuclear Information System (INIS)

    Garcia-Moliner, F.

    1975-01-01

    Basic thermodynamics of a system consisting of two bulk phases with an interface. Solid surfaces: general. Discussion of experimental data on surface tension and related concepts. Adsorption thermodynamics in the Gibbsian scheme. Adsorption on inert solid adsorbents. Systems with electrical charges: chemistry and thermodynamics of imperfect crystals. Thermodynamics of charged surfaces. Simple models of charge transfer chemisorption. Adsorption heat and related concepts. Surface phase transitions

  20. Gas utilization technologies

    International Nuclear Information System (INIS)

    Biljetina, R.

    1994-01-01

    One of the constant challenges facing the research community is the identification of technology needs 5 to 15 years from now. A look back into history indicates that the forces driving natural gas research have changed from decade to decade. In the 1970s research was driven by concerns for adequate supply; in the 1980s research was aimed at creating new markets for natural gas. What then are the driving forces for the 1990s? Recent reports from the natural gas industry have helped define a new direction driven primarily by market demand for natural gas. A study prepared by the Interstate Natural Gas Association of America Foundation entitled ''Survey of Natural Research, Development, and Demonstration RD ampersand D Priorities'' indicated that in the 1990s the highest research priority should be for natural gas utilization and that technology development efforts should not only address efficiency and cost, but environmental and regulatory issues as well. This study and others, such as the report by the American Gas Association (A.G.A.) entitled ''Strategic Vision for Natural Gas Through the Year 2000,'' clearly identify the market sectors driving today's technology development needs. The biggest driver is the power generation market followed by the industrial, transportation, appliance, and gas cooling markets. This is best illustrated by the GRI 1994 Baseline Projection on market growth in various sectors between the year 1992 and 2010. This paper highlights some of the recent technology developments in each one of these sectors

  1. Knowledge-based utility

    International Nuclear Information System (INIS)

    Chwalowski, M.

    1997-01-01

    This presentation provides industry examples of successful marketing practices by companies facing deregulation and competition. The common thread through the examples is that long term survival of today's utility structure is dependent on the strategic role of knowledge. As opposed to regulated monopolies which usually own huge physical assets and have very little intelligence about their customers, unregulated enterprises tend to be knowledge-based, characterized by higher market value than book value. A knowledge-based enterprise gathers data, creates information and develops knowledge by leveraging it as a competitive weapon. It institutionalizes human knowledge as a corporate asset for use over and over again by the use of databases, computer networks, patents, billing, collection and customer services (BCCS), branded interfaces and management capabilities. Activities to become knowledge-based such as replacing inventory/fixed assets with information about material usage to reduce expenditure and achieve more efficient operations, and by focusing on integration and value-adding delivery capabilities, were reviewed

  2. Debating clinical utility.

    Science.gov (United States)

    Burke, Wylie; Laberge, A-M; Press, N

    2010-01-01

    The clinical utility of genetic tests is determined by the outcomes following test use. Like other measures of value, it is often contested. Stakeholders may have different views about benefits and risks and about the importance of social versus health outcomes. They also commonly disagree about the evidence needed to determine whether a test is effective in achieving a specific outcome. Questions may be presented as factual disagreements, when they are actually debates about what information matters or how facts should be interpreted and used in clinical decision-making. Defining the different issues at stake is therefore an important element of policy-making. Key issues include evidence standards for test use, and in particular, the circumstances under which prospective controlled data should be required, as well as evidence on feasibility, cost and equitable delivery of testing; the goals of population-based screening programs, and in particular, the role of social outcomes in evaluating test value; and the appropriate uses and funding of tests that inform non-medical actions. Addressing each of these issues requires attention to stakeholder values and methods for effective deliberation that incorporate consumer as well as health professional perspectives. Copyright 2010 S. Karger AG, Basel.

  3. Gnuastro: GNU Astronomy Utilities

    Science.gov (United States)

    Akhlaghi, Mohammad

    2018-01-01

    Gnuastro (GNU Astronomy Utilities) manipulates and analyzes astronomical data. It is an official GNU package of a large collection of programs and C/C++ library functions. Command-line programs perform arithmetic operations on images, convert FITS images to common types like JPG or PDF, convolve an image with a given kernel or matching of kernels, perform cosmological calculations, crop parts of large images (possibly in multiple files), manipulate FITS extensions and keywords, and perform statistical operations. In addition, it contains programs to make catalogs from detection maps, add noise, make mock profiles with a variety of radial functions using monte-carlo integration for their centers, match catalogs, and detect objects in an image among many other operations. The command-line programs share the same basic command-line user interface for the comfort of both the users and developers. Gnuastro is written to comply fully with the GNU coding standards and integrates well with all Unix-like operating systems. This enables astronomers to expect a fully familiar experience in the source code, building, installing and command-line user interaction that they have seen in all the other GNU software that they use. Gnuastro's extensive library is included for users who want to build their own unique programs.

  4. Automated ISS Flight Utilities

    Science.gov (United States)

    Offermann, Jan Tuzlic

    2016-01-01

    During my internship at NASA Johnson Space Center, I worked in the Space Radiation Analysis Group (SRAG), where I was tasked with a number of projects focused on the automation of tasks and activities related to the operation of the International Space Station (ISS). As I worked on a number of projects, I have written short sections below to give a description for each, followed by more general remarks on the internship experience. My first project is titled "General Exposure Representation EVADOSE", also known as "GEnEVADOSE". This project involved the design and development of a C++/ ROOT framework focused on radiation exposure for extravehicular activity (EVA) planning for the ISS. The utility helps mission managers plan EVAs by displaying information on the cumulative radiation doses that crew will receive during an EVA as a function of the egress time and duration of the activity. SRAG uses a utility called EVADOSE, employing a model of the space radiation environment in low Earth orbit to predict these doses, as while outside the ISS the astronauts will have less shielding from charged particles such as electrons and protons. However, EVADOSE output is cumbersome to work with, and prior to GEnEVADOSE, querying data and producing graphs of ISS trajectories and cumulative doses versus egress time required manual work in Microsoft Excel. GEnEVADOSE automates all this work, reading in EVADOSE output file(s) along with a plaintext file input by the user providing input parameters. GEnEVADOSE will output a text file containing all the necessary dosimetry for each proposed EVA egress time, for each specified EVADOSE file. It also plots cumulative dose versus egress time and the ISS trajectory, and displays all of this information in an auto-generated presentation made in LaTeX. New features have also been added, such as best-case scenarios (egress times corresponding to the least dose), interpolated curves for trajectories, and the ability to query any time in the

  5. Prokaryotic silicon utilizing microorganisms in the biosphere

    Science.gov (United States)

    Gupta, D.; Das, S.

    2012-12-01

    Although a little study has been done to determine the silicon utilizing prokaryotes, our previous experiments indicated that almost all Gram-positive bacteria are silicon utilizing; one of them, Streptococci survived exposure on the lunar surface for a long period in experiment done by others. Our initial experiments with these Gram positive microorganisms showed that there were limited growths of these microorganisms on carbon free silicate medium probably with the help of some carry over carbon and nitrogen during cultivation procedures. However, increase in growth rate after repeated subcultures could not be explained at present. The main groups of prokaryotes which were found silicon utilizing microorganisms were Mycobacterium, Bacillus, Nocardia, Streptomyces, Staphylococcus, Streptococcus, Lactobacillus, and Clostridium. In a another previous study by us when silicon level was studied in such grown up cells on carbon "free" silicate medium by electron prove microanalyser, it was found that silicon in cells grown on carbon "free" silicate medium was much higher (24.9%) than those grown on conventional carbon based medium (0.84%). However, these initial findings are encouraging for our future application of this group of organisms on extraterrestrial surfaces for artificial micro-ecosystem formation. It was found that when electropositive elements are less in extraterrestrial situation, then polymerization of silicon-oxygen profusion may occur easily, particularly in carbon and nitrogen paucity in the rocky worlds of the Universe.

  6. Buprenorphine transdermal system utilization.

    Science.gov (United States)

    Wallace, Laura; Kadakia, Aditi

    2017-01-01

    To evaluate utilization patterns in patients initiating buprenorphine transdermal system (BTDS), CIII, and estimate the proportion decreasing their total opioid dose over time. This retrospective cohort study used data from the Truven Health Analytics MarketScan® Commercial Claims and Encounters Database from 1 January 2011 through 31 December 2015. Eligible individuals were adults aged 18-64 years newly dispensed BTDS (index prescription) who had at least six months of insurance coverage prior to (baseline period) and following (study period) the index prescription. Back and neck pain was the most common pain condition in the study population (n = 31,533) and 88% were dispensed opioids in the baseline period. Nearly half (48%) received BTDS in a strength of 10 mcg/hour as their index prescription. Most (80%) patients prescribed BTDS had concomitant prescriptions for other opioids, chiefly immediate-release (IR) opioids (77%). During the baseline period, median opioid dose among patients prescribed opioids was 50 morphine-equivalent doses (MED), with 33% of patients using nonsteroidal anti-inflammatory drugs and 44% adjuvant analgesics. During the study period, BTDS use lasted a median 30 days and mean 100 days. Median dose of BTDS remained largely constant, and median dose of all opioids during continuous use of BTDS was 65.6 units MED. However, 24% of patients reduced total units MED from the baseline period (median mean dose, 74.5 units MED) until the end of the study period (42.8). Most patients initiating treatment with BTDS had a history of treatment with IR opioids. Though the average change in total opioid daily dose after patients were prescribed BTDS was modest, an important subpopulation of approximately one-quarter of patients were able to markedly reduce their total units MED compared with prior opioid therapy. BTDS should be investigated as an option to help patients step down from higher opioid doses.

  7. wssa_utils: WSSA 12 micron dust map utilities

    Science.gov (United States)

    Meisner, Aaron M.; Finkbeiner, Douglas P.

    2014-02-01

    wssa_utils contains utilities for accessing the full-sky, high-resolution maps of the WSSA 12 micron data release. Implementations in both Python and IDL are included. The code allows users to sample values at (longitude, latitude) coordinates of interest with ease, transparently mapping coordinates to WSSA tiles and performing interpolation. The wssa_utils software also serves to define a unique WSSA 12 micron flux at every location on the sky.

  8. Facility Utilization Reports - FAA Aviation Information Utilization Reports

    Data.gov (United States)

    Department of Transportation — Provides: (1) Space management and planning, including area calculations, tracking space by organization and employee, and monitoring space utilization information....

  9. Cryogenic surface ion traps

    International Nuclear Information System (INIS)

    Niedermayr, M.

    2015-01-01

    Microfabricated surface traps are a promising architecture to realize a scalable quantum computer based on trapped ions. In principle, hundreds or thousands of surface traps can be located on a single substrate in order to provide large arrays of interacting ions. To this end, trap designs and fabrication methods are required that provide scalable, stable and reproducible ion traps. This work presents a novel surface-trap design developed for cryogenic applications. Intrinsic silicon is used as the substrate material of the traps. The well-developed microfabrication and structuring methods of silicon are utilized to create simple and reproducible traps. The traps were tested and characterized in a cryogenic setup. Ions could be trapped and their life time and motional heating were investigated. Long ion lifetimes of several hours were observed and the measured heating rates were reproducibly low at around 1 phonon per second at a trap frequency of 1 MHz. (author) [de

  10. Privatization of municipal electrical utilities

    International Nuclear Information System (INIS)

    Carr, J.

    1998-01-01

    The challenges and special issues which arise through the sale of a municipal electric utility were discussed. The recent sales of two utilities, the Kentville Electric Commission in Nova Scotia and Cornwall Electric in Ontario, were used as examples to show how the sale of an electric utility differs from the sale of most business enterprises. Municipal utilities are integral parts of the communities they serve which introduces several complexities into the sale. Factors that require special attention in the sale of the utilities, including electricity rates, local accountability, treatment of employees and local economic development, and the need for a comprehensive communication program to deal with the substantial public interest that sale of a municipal utility will engender, were reviewed

  11. Mox fuel utilization in ATR

    OpenAIRE

    下村 和生; 川太 徳夫

    1987-01-01

    ATR, a heavy-water moderated boiling-light-water cooled reactor developed in Japan, is a unique reactor with out-standing flexibility regarding nuclear fuel utilization, because it has superior properties concerning the utilization of plutonium, recovered uranium and depleted uranium. The development of this type of reactor is expected to contribute both to the stable supply of energy and to the establishment of plutonium utilization in Japan. Much effort has been and will be made on the deve...

  12. Utility deregulation and AMR technology

    International Nuclear Information System (INIS)

    Moore, G.

    1991-01-01

    This article reviews the effects of deregulation on other utilities and services and examines how the electric utilities can avoid the worst of these effects and capitalize of the best aspects of competition in achieving marketing excellence. The article presents deregulation as a customer service and underscores the need for utilities to learn to compete aggressively and intelligently and provide additional services available through technology such as automated meter reading

  13. VT Electric Utility Franchise Areas

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) ELCFRANCHISE includes Vermont's Electric Utility Franchise boundaries. It is a compilation of many data sources. The boundaries are approximate...

  14. The utility target market model

    International Nuclear Information System (INIS)

    Leng, G.J.; Martin, J.

    1994-01-01

    A new model (the Utility Target Market Model) is used to evaluate the economic benefits of photovoltaic (PV) power systems located at the electrical utility customer site. These distributed PV demand-side generation systems can be evaluated in a similar manner to other demand-side management technologies. The energy and capacity values of an actual PV system located in the service area of the New England Electrical System (NEES) are the two utility benefits evaluated. The annual stream of energy and capacity benefits calculated for the utility are converted to the installed cost per watt that the utility should be willing to invest to receive this benefit stream. Different discount rates are used to show the sensitivity of the allowable installed cost of the PV systems to a utility's average cost of capital. Capturing both the energy and capacity benefits of these relatively environmentally friendly distributed generators, NEES should be willing to invest in this technology when the installed cost per watt declines to ca $2.40 using NEES' rated cost of capital (8.78%). If a social discount rate of 3% is used, installation should be considered when installed cost approaches $4.70/W. Since recent installations in the Sacramento Municipal Utility District have cost between $7-8/W, cost-effective utility applications of PV are close. 22 refs., 1 fig., 2 tabs

  15. Utility strategies - affiliated power marketers

    Energy Technology Data Exchange (ETDEWEB)

    Coffey, J.F. [Aquila Energy Corp., Omaha, NE (United States)

    1994-12-31

    The regulation of affiliated power marketers (APM) is discussed. Any electric utility affiliates that own or control generation must not have market power in the relevant market, which is defined as the utility`s first-tier markets. One can prove that its affiliates do not have generation dominance by: (a) showing that its entire generating capacity is committed under long term contract, (b) showing that its affiliates already are authorized to sell at market-based rates, or (c) submitting a market analysis which demonstrates that the affiliates do not possess generation market power. The electric utility affiliates must have a transmission tariff on file which provides for comparable transmission services. The APM must agree not to buy power from, or sell power to its electric utility affiliate without prior approval by the Federal Energy Regulatory Commission (FERC). The APM must notify FERC if it sells power to, buys power from, or obtains transmission service from a utility that has any business relationship with any affiliates. Any non-sales services provided by the utility affiliates must not be priced below market value. Procedures must ensure that market information is not shared between the utility and the APM, or shared on a comparable basis with non-affiliates. A continuing obligation exists for the APM to notify FERC of any change in these criteria occurring after approval is granted. Concerns with these provisions and suggested improvements are discussed.

  16. Superhydrophobic surfaces

    Science.gov (United States)

    Wang, Evelyn N; McCarthy, Matthew; Enright, Ryan; Culver, James N; Gerasopoulos, Konstantinos; Ghodssi, Reza

    2015-03-24

    Surfaces having a hierarchical structure--having features of both microscale and nanoscale dimensions--can exhibit superhydrophobic properties and advantageous condensation and heat transfer properties. The hierarchical surfaces can be fabricated using biological nanostructures, such as viruses as a self-assembled nanoscale template.

  17. Spherical Surfaces

    DEFF Research Database (Denmark)

    Brander, David

    2016-01-01

    We study surfaces of constant positive Gauss curvature in Euclidean 3-space via the harmonicity of the Gauss map. Using the loop group representation, we solve the regular and the singular geometric Cauchy problems for these surfaces, and use these solutions to compute several new examples. We give...

  18. Computer aided surface representation

    Energy Technology Data Exchange (ETDEWEB)

    Barnhill, R.E.

    1989-02-09

    The central research problem of this project is the effective representation and display of surfaces, interpolating to given information, in three or more dimensions. In a typical problem, we wish to create a surface from some discrete information. If this information is itself on another surface, the problem is to determine a surface defined on a surface,'' which is discussed below. Often, properties of an already constructed surface are desired: such geometry processing'' is described below. The Summary of Proposed Research from our original proposal describes the aims of this research project. This Summary and the Table of Contents from the original proposal are enclosed as an Appendix to this Progress Report. The broad sweep from constructive mathematics through algorithms and computer graphics displays is utilized in the research. The wide range of activity, directed in both theory and applications, makes this project unique. Last month in the first Ardent Titan delivered in the State of Arizona came to our group, funded by the DOE and Arizona State University. Although the Titan is a commercial product, its newness requires our close collaboration with Ardent to maximize results. During the past year, four faculty members and several graduate research assistants have worked on this DOE project. The gaining of new professionals is an important aspect of this project. A listing of the students and their topics is given in the Appendix. The most significant publication during the past year is the book, Curves and Surfaces for Computer Aided Geometric Design, by Dr. Gerald Farin. This 300 page volume helps fill a considerable gap in the subject and includes many new results on Bernstein-Bezier curves and surfaces.

  19. Evaluating Utility Gloves as a Potential Reservoir for Pathogenic Bacteria.

    Science.gov (United States)

    Grant, Kathy L; Naber, E Donald; Halteman, William A

    2015-08-01

    This pilot study sought to determine the rate and degree to which gram-negative Klebsiella pneumoniae, Escherichia coli and Pseudomonas aeruginosa and gram-positive Staphylococcus aureus occurred on the inside of utility gloves used at University of Maine at Augusta, Dental Health Programs' dental hygiene clinic. Five steam autoclave utility gloves were randomly selected to serve as control and a convenience sample of 10 used utility gloves were selected from the sterilization area. A sample was collected from a predetermined surface area from the inside of each steam autoclave utility glove and used utility glove. Each sample was used to inoculate a Petri plate containing 2 types of culture media. Samples were incubated at 37° C for 30 to 36 hours in aerobic conditions. Colony forming units (CFU) were counted. Confidence intervals (CI) estimated the rate of contamination with gram-negative K. pneumoniae, E. coli and P. aeruginosa on the inside of steam autoclave utility gloves to be n=33 95% CL [0.000, 0.049], used utility gloves to be n=70, 95% CL [0.000, 0.0303]. Data estimated the rate of contamination with gram-positive S. aureus on the inside of steam autoclave utility gloves to be n=35, 95% CL [0.233, 0.530], used utility gloves to be n=70, 95% CL [0.2730, 0.4975]. Culture media expressed a wide range of CFU from 0 to over 200. The risk of utility glove contamination with gram-negative bacteria is likely low. The expressed growth of S. aureus from steam autoclave utility gloves controls raises questions about the effectiveness and safety of generally accepted sterilization standards for the governmentally mandated use of utility gloves. Copyright © 2015 The American Dental Hygienists’ Association.

  20. Surface active monomers synthesis, properties, and application

    CERN Document Server

    Borzenkov, Mykola

    2014-01-01

    This brief includes information on the background?of and development of synthesis of various types of surface active monomers. The authors explain the importance of utilization of surface active monomers for creation of surface active polymers? and the various biomedical applications of such compounds . This brief introduces techniques for the synthesis of novel types of surface active monomers, their colloidal and polymerizable properties and application for needs of medicine and biology.

  1. Analysed foundation sea surface temperature, global

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The through-cloud capabilities of microwave radiometers provide a valuable picture of global sea surface temperature (SST). To utilize this, scientists at Remote...

  2. Hualapai Tribal Utility Development Project

    Energy Technology Data Exchange (ETDEWEB)

    Hualapai Tribal Nation

    2008-05-25

    The first phase of the Hualapai Tribal Utility Development Project (Project) studied the feasibility of establishing a tribally operated utility to provide electric service to tribal customers at Grand Canyon West (see objective 1 below). The project was successful in completing the analysis of the energy production from the solar power systems at Grand Canyon West and developing a financial model, based on rates to be charged to Grand Canyon West customers connected to the solar systems, that would provide sufficient revenue for a Tribal Utility Authority to operate and maintain those systems. The objective to establish a central power grid over which the TUA would have authority and responsibility had to be modified because the construction schedule of GCW facilities, specifically the new air terminal, did not match up with the construction schedule for the solar power system. Therefore, two distributed systems were constructed instead of one central system with a high voltage distribution network. The Hualapai Tribal Council has not taken the action necessary to establish the Tribal Utility Authority that could be responsible for the electric service at GCW. The creation of a Tribal Utility Authority (TUA) was the subject of the second objective of the project. The second phase of the project examined the feasibility and strategy for establishing a tribal utility to serve the remainder of the Hualapai Reservation and the feasibility of including wind energy from a tribal wind generator in the energy resource portfolio of the tribal utility (see objective 2 below). It is currently unknown when the Tribal Council will consider the implementation of the results of the study. Objective 1 - Develop the basic organizational structure and operational strategy for a tribally controlled utility to operate at the Tribe’s tourism enterprise district, Grand Canyon West. Coordinate the development of the Tribal Utility structure with the development of the Grand Canyon

  3. Development of technologies for utilizing geothermal energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    In verifying the effectiveness of the deep geothermal resource exploration technology, development is being carried out on a fracture-type reservoir exploration method. The seismic exploration method investigates detailed structures of underground fracture systems by using seismic waves generated on the ground surface. Verification experiments for fiscal 1994 were carried out by selecting the Kakkonda area in which small fracture networks form reservoir beds. Geothermal resources in deep sections (deeper than 2000 m with temperatures higher than 350{degree}C) are promising in terms of amount of the resources, but anticipated with difficulty in exploration and impediments in drilling. To avoid these risks, studies are being progressed on the availability of resources in deep sections, their utilization possibility, and technologies of effective exploration and drilling. This paper summarizes the results of deep resource investigations during fiscal 1994. It also describes such technological development as hot water utilizing power generation. Development is performed on a binary cycle power generation plant which pumps and utilizes hot water of 150 to 200{degree}C by using a downhole pump. The paper also reports development on element technologies for hot rock power generation systems. It also dwells on development of safe and effective drilling and production technologies for deep geothermal resources.

  4. Polarizability of a metallic surface

    International Nuclear Information System (INIS)

    Moraga, L.A.; Esparza, C.

    1981-01-01

    The surface dielectric operator for a semi-infinite 'Jellium' in the random phase approximation is calculated in a semi-analytical form, utilizing as zero-order approximation the Green's function for the finite height well potential. From this one, the interaction potential is calculated with different additional approximations. (L.C.) [pt

  5. Dealing with the difficult utility

    International Nuclear Information System (INIS)

    Keats, D.E.; Sundquist, M.J.; Cross, J.P.

    1991-01-01

    STS HydroPower, Ltd. (STS) is an independent hydroelectric power developer involved in the full scope of hydroelectric activities. This includes the permitting, design, financing, turbine design and manufacturing, site construction and operation of small to mid-sized hydroelectric sites across the United States. At the present time, STS owns and operates nine sites in four states with a combined capacity of 20 megawatts. In dealing with the implementation of these sites, STS has dealt with five different utilities. In addition, in pursuing additional development opportunities throughout the United States, STS has had contact with numerous other utilities. During this time it would be fair to conclude that each of these utilities has exhibited its own personality with respect to dealing with independent developers. To the credit of the utility industry, the majority of these utilities have been helpful and supportive of independent projects, but a small number of utilities have approached projects from an initial and continuing adversarial position. The purpose of this paper is to examine those options and procedures available to the developer when a utility is encountered with a negative predisposition

  6. Public utility economics and finance

    Energy Technology Data Exchange (ETDEWEB)

    Howe, K.M.; Rasmussen, E.F.

    1982-01-01

    Students will find this presentation of the economic and institutional arrangements that surround the area of public utilities helpful in understanding current regulations and possibly suggesting solutions for future problems. The eight sections of the text cover: (1) an introduction to the nature and types of services provided by public utilities; (2) economic characteristics; (3) legal concepts; (4) traditional issues in regulation; (5) independent regulatory commissions; (6) a critique of public-utility regulation; (7) pricing and the regulation of consumer demand; and (8) capital budgeting and finance. 490 references, 37 figures, 38 tables. (DCK)

  7. Surface boxplots

    KAUST Repository

    Genton, Marc G.

    2014-01-22

    In this paper, we introduce a surface boxplot as a tool for visualization and exploratory analysis of samples of images. First, we use the notion of volume depth to order the images viewed as surfaces. In particular, we define the median image. We use an exact and fast algorithm for the ranking of the images. This allows us to detect potential outlying images that often contain interesting features not present in most of the images. Second, we build a graphical tool to visualize the surface boxplot and its various characteristics. A graph and histogram of the volume depth values allow us to identify images of interest. The code is available in the supporting information of this paper. We apply our surface boxplot to a sample of brain images and to a sample of climate model outputs.

  8. Convex surfaces

    CERN Document Server

    Busemann, Herbert

    2008-01-01

    This exploration of convex surfaces focuses on extrinsic geometry and applications of the Brunn-Minkowski theory. It also examines intrinsic geometry and the realization of intrinsic metrics. 1958 edition.

  9. Surface decontamination

    International Nuclear Information System (INIS)

    Silva, S. da; Teixeira, M.V.

    1986-06-01

    The general methods of surface decontamination used in laboratory and others nuclear installations areas, as well as the procedures for handling radioactive materials and surfaces of work are presented. Some methods for decontamination of body external parts are mentioned. The medical supervision and assistance are required for internal or external contamination involving or not lesion in persons. From this medical radiation protection decontamination procedures are determined. (M.C.K.) [pt

  10. Surface phonons

    CERN Document Server

    Wette, Frederik

    1991-01-01

    In recent years substantial progress has been made in the detection of surface phonons owing to considerable improvements in inelastic rare gas scattering tech­ niques and electron energy loss spectroscopy. With these methods it has become possible to measure surface vibrations in a wide energy range for all wave vectors in the two-dimensional Brillouin zone and thus to deduce the complete surface phonon dispersion curves. Inelastic atomic beam scattering and electron energy loss spectroscopy have started to play a role in the study of surface phonons similar to the one played by inelastic neutron scattering in the investigation of bulk phonons in the last thirty years. Detailed comparison between experimen­ tal results and theoretical studies of inelastic surface scattering and of surface phonons has now become feasible. It is therefore possible to test and to improve the details of interaction models which have been worked out theoretically in the last few decades. At this point we felt that a concise, co...

  11. State Drug Utilization Data 2013

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  12. State Drug Utilization Data 1996

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  13. State Drug Utilization Data 1993

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  14. State Drug Utilization Data 1995

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  15. State Drug Utilization Data 1997

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  16. State Drug Utilization Data 2015

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  17. State Drug Utilization Data 1998

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  18. State Drug Utilization Data 1991

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  19. State Drug Utilization Data 1992

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  20. State Drug Utilization Data 1994

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  1. State Drug Utilization Data 2001

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  2. State Drug Utilization Data 2005

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  3. State Drug Utilization Data 2011

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  4. State Drug Utilization Data 2006

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  5. State Drug Utilization Data 2014

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  6. State Drug Utilization Data 2012

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  7. State Drug Utilization Data 2009

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  8. State Drug Utilization Data 2004

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  9. State Drug Utilization Data 2008

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  10. State Drug Utilization Data 2002

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  11. Growth of hydrocarbon utilizing microorganisms

    Digital Repository Service at National Institute of Oceanography (India)

    Bhosle, N.B.; Mavinkurve, S.

    Two isolates from marine mud having broad spectrum hydrocarbon utilizing profile were identified as Arthrobacter simplex and Candida tropicalis.Both the organisms grew exponentially on crude oil. The cell yield of the organisms was influenced...

  12. Decentralized method for utility regulation

    Energy Technology Data Exchange (ETDEWEB)

    Loeb, M. (North Carolina State Univ., Raleigh); Magat, W.A.

    1979-10-01

    A new institutional arrangement for regulating utilities is suggested that minimizes the costs of natural monopolies. A mixture of regulation and franchising, the plan draws on the advantages of each and eliminates many of the problems. The proposal allows utilities to set their own price on the basis of demand and marginal-cost projections. Subsidies are provided by the regulatory agency if there is a consumer surplus. The system encourages the utility to select a competitive price and to produce only the amount of service needed. Operating efficiency is encouraged by rewarding cost reductions and discouraging cost overstatement at the rate review. The regulatory agency would not need to take action to bring price and marginal costs into equality. The franchise sale can be made by competitive bidding, in which the bidders would capitalize part or all of the subsidy or the regulatory agency could recover the subsidy in a lump-sum tax on the utility.

  13. Medicare Utilization for Part B

    Data.gov (United States)

    U.S. Department of Health & Human Services — This link takes you to the Medicare utilization statistics for Part B (Supplementary Medical Insurance SMI) which includes the Medicare Part B Physician and Supplier...

  14. State Drug Utilization Data 2017

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  15. State Drug Utilization Data 2016

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  16. State Drug Utilization Data 2000

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  17. State Drug Utilization Data 2007

    Data.gov (United States)

    U.S. Department of Health & Human Services — Drug utilization data are reported by states for covered outpatient drugs that are paid for by state Medicaid agencies since the start of the Medicaid Drug Rebate...

  18. Build Resilience at Your Utility

    Science.gov (United States)

    CREAT allows users to evaluate potential impacts of climate change on their utility and to evaluate adaptation options to address them using both traditional risk assessment and scenario-based decision making.

  19. Photovoltaics: New opportunities for utilities

    Energy Technology Data Exchange (ETDEWEB)

    1991-07-01

    This publication presents information on photovoltaics. The following topics are discussed: Residential Photovoltaics: The New England Experience Builds Confidence in PV; Austin's 300-kW Photovoltaic Power Station: Evaluating the Breakeven Costs; Residential Photovoltaics: The Lessons Learned; Photovoltaics for Electric Utility Use; Least-Cost Planning: The Environmental Link; Photovoltaics in the Distribution System; Photovoltaic Systems for the Rural Consumer; The Issues of Utility-Intertied Photovoltaics; and Photovoltaics for Large-Scale Use: Costs Ready to Drop Again.

  20. The 1990 utility tax conference

    International Nuclear Information System (INIS)

    Norris, J.E.

    1990-01-01

    This article reports on the Sixth Annual Utility Tax Conference held in Washington, D.C. in October. Topics of the conference concerned tax issues associated with depreciable assets, employee benefits plans, valuation on utility property, pollution control, and restructuring and reorganization. Also discussed briefly were the tax changes being considered at that time as part of the negotiation of the details of the Omnibus Budget Reconciliation Act

  1. Strategies for the plutonium utilization

    International Nuclear Information System (INIS)

    Zouain, D.M.; Lima, J.O.V.; Sakamoto, L.H.

    1981-11-01

    A review of the activities involving plutonium (its recycle, utilization and technological status and perspectives) is done. These informations are useful for an economic viability study for the plutonium utilization in thermal reactors (recycling) and in fast breeders reactor (FBR), trying to collect the major number of informations about these subjects. The initial phase describes the present status and projections of plutonium accumulation and requirements. Then, the technological process are described and some strategies are analyzed. (E.G.) [pt

  2. Critical paths to coal utilization

    Energy Technology Data Exchange (ETDEWEB)

    Hill, G.R.

    1977-01-01

    The present dilemma of energy producers, converters, and policy decision makers is presented. The consequences of environmental control regulations, coupled with the need for conservation and energy, and of energy resources on the increased utilization of coal, are discussed. Several recent technical accomplishments that make possible increased utilization of coal for power generation are described. Groundwork is laid for discussion of the technical development that must occur if the United States is to retain its energy viability.

  3. Using nutrient utilization patterns to determine the source of ...

    African Journals Online (AJOL)

    AJB SERVER

    isolates were predicted to be originating from the human source. The results indicate that livestock are the primary contributors to fecal pollution in this hypereutrophic Iowa lake. Key words: Nutrient utilization patterns, Escherichia coli, bacterial source tracking, Silver Lake, Delaware,. Iowa. INTRODUCTION. Surface water ...

  4. Using nutrient utilization patterns to determine the source of ...

    African Journals Online (AJOL)

    Identifying the sources of fecal contaminants in surface water bodies such as rivers, lakes and beaches is of importance for environmental safety, public health safety, food safety and regulatory purposes. Nutrient utilization patterns (NUPs) were used as a bacterial source tracking technique to identify the possible sources of ...

  5. Polarization-controlled luminaires utilizing multiple Fresnel reflections

    Science.gov (United States)

    Falicoff, Waqidi; Minano, Juan C.; Caulfield, H. John; Alvarez, Roberto

    2003-11-01

    A novel luminaire utilizes repeated Fresnel reflections by angled surfaces to transform a small collimated input beam into a controlled output pattern with a high degree of polarization, either linear or radial. Applications to backlighting, front-lighting, optical communications and automotive lighting will be discussed.

  6. Seismic response of concrete gravity dam reinforced with FRP sheets on dam surface

    Directory of Open Access Journals (Sweden)

    Hong Zhong

    2013-10-01

    Full Text Available This paper aims at exploring the effects of anti-seismic reinforcement with the fiber-reinforced polymer (FRP material bonded to the dam surface in dam engineering. Time-history analysis was performed to simulate the seismic failure process of a gravity dam that was assumed to be reinforced at the locations of slope discontinuity at the downstream surface, part of the upstream face, and the dam heel. A damage model considering the influence of concrete heterogeneity was used to model the nonlinearity of concrete. A bond-slip model was applied to the interface between FRP and concrete, and the reinforcement mechanism was analyzed through the bond stress and the stress in FRP. The results of the crack pattern, displacement, and acceleration of the reinforced dam were compared with those of the original one. It is shown that FRP, as a reinforcement material, postpones the occurrence of cracks and slows the crack propagation, and that cracks emanating from the upstream surface and downstream surface are not connected, meaning that the reinforced dam can retain water-impounding function when subjected to the earthquake. Anti-seismic reinforcement with FRP is therefore beneficial to improving the seismic resistant capability of concrete dams.

  7. Ice Surfaces

    Science.gov (United States)

    Shultz, Mary Jane

    2017-05-01

    Ice is a fundamental solid with important environmental, biological, geological, and extraterrestrial impact. The stable form of ice at atmospheric pressure is hexagonal ice, Ih. Despite its prevalence, Ih remains an enigmatic solid, in part due to challenges in preparing samples for fundamental studies. Surfaces of ice present even greater challenges. Recently developed methods for preparation of large single-crystal samples make it possible to reproducibly prepare any chosen face to address numerous fundamental questions. This review describes preparation methods along with results that firmly establish the connection between the macroscopic structure (observed in snowflakes, microcrystallites, or etch pits) and the molecular-level configuration (detected with X-ray or electron scattering techniques). Selected results of probing interactions at the ice surface, including growth from the melt, surface vibrations, and characterization of the quasi-liquid layer, are discussed.

  8. Moist-Soil Impoundments for Wetland Wildlife.

    Science.gov (United States)

    1999-10-01

    Digitaria spp. Aster Aster spp. Cultivated rice Oryza sativa Barnyard grass Echinochloa crusgalli var. mitis Curltop ladysthumb Polygonum...Long-term pump costs will vary according to fuel prices, repair and maintenance, and spe- cific situations; however, long-term cost assessment

  9. Reconnaissance of the chemical quality of surface waters of the Neches River basin, Texas

    Science.gov (United States)

    Hughes, Leon S.; Leifeste, Donald K.

    1967-01-01

    with less than 30 ppm hardness. The chloride concentrations are less than 20 ppm in surface water in the southern half of the basin and usually range from 20 to 100 ppm in the northern half of the basin. Concentrations greater than 100 ppm are found only where pollution is occurring. The Neches River basin has an abundance of surface water, but uneven distribution of runoff makes storage projects necessary to provide dependable water supplies. The principal existing reservoirs, with the exception of Striker Creek Reservoir, contain water of excellent quality. Chemical-quality data for the Striker Creek drainage area indicate that its streams are affected by .the disposal of brines associated with oil production. Sam Rayburn Reservoir began impounding water in 1965. The water impounded should prove of acceptable quality for most uses, but municipal and industrial wastes released into the Angelina River near Lufkin may have a degrading effect on the quality of the water, especially during extended periods of low flows. Water available for storage at the many potential reservoir sites will be of good quality; but, if the proposed salt-water barrier is to impound acceptable water, the disposal of oilfield brine into Pine Island Bayou should be discontinued.

  10. Surfacing Moves

    DEFF Research Database (Denmark)

    Lutz, Peter

    2013-01-01

    such as schedules, machines, and aging bodies. To this end, the article also experiments with ‘surfacing’ as an ethnographic heuristic for figuring these different ‘spatial-timings’. The article concludes that surfacing matters not only in senior home care but also in the field-desks of ethnographic analysis....

  11. Attack surfaces

    DEFF Research Database (Denmark)

    Gruschka, Nils; Jensen, Meiko

    2010-01-01

    The new paradigm of cloud computing poses severe security risks to its adopters. In order to cope with these risks, appropriate taxonomies and classification criteria for attacks on cloud computing are required. In this work-in-progress paper we present one such taxonomy based on the notion...... of attack surfaces of the cloud computing scenario participants....

  12. Calculating utility prudency issue costs

    International Nuclear Information System (INIS)

    Nielsen, K.R.

    1985-01-01

    The nuclear industry, particularly utilities and their construction, engineering and vendor agents, is faced with a surging increase in prudency management audits. What started as primarily a nuclear project-oriented requirement has spread to encompass most significant utility capital construction projects. Such audits are often a precedent condition to commencement of rate hearings. The cost engineer, a primary major capital construction project participant, is required to develop or critique ''prudency issue'' costs as part of such audits. Although utility costs in the broadest sense are potentially at issue, this paper concentrates on the typical project/construction management costs. The costs of design, procurement and construction are all subject to the calculation process

  13. Ethanolamine utilization in Vibrio alginolyticus

    Science.gov (United States)

    2012-01-01

    Abstract Ethanolamine is used as an energy source by phylogenetically diverse bacteria including pathogens, by the concerted action of proteins from the eut-operon. Previous studies have revealed the presence of eutBC genes encoding ethanolamine-ammonia lyase, a key enzyme that breaks ethanolamine into acetaldehyde and ammonia, in about 100 bacterial genomes including members of gamma-proteobacteria. However, ethanolamine utilization has not been reported for any member of the Vibrio genus. Our comparative genomics study reveals the presence of genes that are involved in ethanolamine utilization in several Vibrio species. Using Vibrio alginolyticus as a model system we demonstrate that ethanolamine is better utilized as a nitrogen source than as a carbon source. Reviewers This article was reviewed by Dr. Lakshminarayan Iyer and Dr. Vivek Anantharaman (nominated by Dr. L Aravind). PMID:23234435

  14. The European Utility Requirement Document

    International Nuclear Information System (INIS)

    Roche, I.I.

    1999-01-01

    The major European electricity producers work on a common requirement document for future LWR plants since 1992. They aim at requirements acceptable together by the owners, the public and the authorities. Thus the designers can develop standard LWR designs acceptable everywhere in Europe and the utilities can open their consultations to vendors on common bases. Such a standardisation promotes an improvement of generation costs and of safety : public and authorities acceptance should be improved as well ; significant savings are expected in development and construction costs. Since the early stages of the project, the EUR group has grown significantly. It now includes utilities from nine European countries. Utilities from two other European countries are joining the group. Specific cooperation agreements are also in progress with a few extra-European partners

  15. The NRC and utility finances

    International Nuclear Information System (INIS)

    Byus, L.C.

    1992-01-01

    In a speech before the National Association of Regulatory Utility Commissioners in November 1991, Nuclear Regulatory Commission Chairman Ivan Selin presented what he called an open-quotes expansion of the concept of safety beyond our previous narrow bounds.close quotes He went on to explain, open-quotes To be seen as successful and safe operators of nuclear facilities, utilities must have safe and predictable cash flows.close quotes While there is little disagreement that the concepts of successful plant operations and financial strength go hand in hand, the relationship between the two is not clear. Which came first, successful operation of generating plants or financial strength? Selin's views on NRC involvement in financial aspects of utility operation in the United States are sure to stimulate debate on the issue

  16. Utilization trend of wood species utilized in furniture industry in ...

    African Journals Online (AJOL)

    The utilization trend of four commonly used wood species and two lesser used wood species that are used for furniture making was examined. The wood species are Mansonia altissima (Mansonia), Khaya ivorensis (Khaya), Cordia millenii (Cordia) and Tectona grandis (Teak) as commonly used wood species; Aningeria ...

  17. 24 CFR 5.632 - Utility reimbursements.

    Science.gov (United States)

    2010-04-01

    ... Section 8 Project-Based Assistance Family Payment § 5.632 Utility reimbursements. (a) Applicability. This... the utility supplier to pay the utility bill on behalf of the family. If the PHA elects to pay the utility supplier, the PHA must notify the family of the amount paid to the utility supplier. (3) In the...

  18. 'Utility marketing' as an oxymoron

    International Nuclear Information System (INIS)

    Gedge, P.

    1996-01-01

    Electricity industry restructuring through the elimination of monopolies and the introduction of competition was examined. A distinction was made between marketing a product and brand marketing, emphasizing the customer loyalty, customer confidence and high profitability associated with brand names. The meaning of 'brand' in general and particularly in relation to electric power was explained. The old and the new utilities world were contrasted, and the place and importance of marketing in the deregulated, customer choice-based, market-driven new utilities world was described

  19. E-Commerce for utilities

    Energy Technology Data Exchange (ETDEWEB)

    Malicky, M. [Metzler and Associates, Deerfield, IL (United States)

    1999-07-01

    The use of E-Commerce by energy utility and service companies was discussed. E-Commerce was described as being all communication via the web including Internet, Intranet and Extranet. E-Commerce communication includes the exchange of information, data, money services, products, ideas, conversations, knowledge, inventory and events. E-Commerce can be applied to electric and gas utilities to enhance energy marketing, delivery, retail energy, energy services, retail services and customer satisfaction. This means of communication is quickly becoming an essential part of customer care strategy. It reduces costs and improves performance. It was forecasted that E-Commerce will more than double from 1998 to 2001. 15 refs.

  20. Mars in Situ Resource Utilization Technology Evaluation

    Science.gov (United States)

    Muscatello, Anthony C.; Santago-Maldonado, Edgardo

    2012-01-01

    We have examined the technologies required to enable Mars In-Situ Resource Utilization (ISRU) because our understanding of Mars resources has changed significantly in the last five years as a result of recent robotic missions to the red planet. Two major developments, (1) confirmation of the presence of near-surface water in the form of ice in very large amounts at high latitudes by the Phoenix Lander and (2) the likely existence of water at lower latitudes in the form of hydrates or ice in the top one meter of the regolith, have the potential to change ISRU technology selection. A brief technology assessment was performed for the most promising Mars atmospheric gas processing techniques: Reverse Water Gas Shift (RWGS) and Methanation (aka Sabatier), as well as an overview of soil processing technology to extract water from Martian soil.

  1. Utility Energy Services Contracts: Enabling Documents

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-05-01

    Utility Energy Services Contracts: Enabling Documents provides materials that clarify the authority for Federal agencies to enter into utility energy services contracts (UESCs), as well as sample documents and resources to ease utility partnership contracting.

  2. Waste heat utilization in agriculture

    International Nuclear Information System (INIS)

    Horacek, P.

    1983-01-01

    The Proceedings contain 17 papers presented at meetings of the Working Group for Waste Heat Utilization of the Committee of the European Society of Nuclear Methods in Agriculture of which 7 fall under the INIS scope. The working group met in May 1980 in Brno, Czechoslovakia, in October 1981 in Aberdeen, Scotland and in September 1982 in Brno. (Z.M.)

  3. Introduction to drug utilization research

    DEFF Research Database (Denmark)

    Wettermark, Björn; Elseviers, Monique; Almarsdóttir, Anna Birna

    2016-01-01

    Qualitative research methods derive from the social sciences. Their use in drug utilization research is increasingly widespread, especially in understanding patient and prescriber perspectives. The main focus in qualitative research is exploration of a given phenomenon in order to get a wider...

  4. Production and utilization of radioisotopes

    Energy Technology Data Exchange (ETDEWEB)

    Sekine, Toshiaki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Matsuoka, Hiromitsu

    1999-03-01

    A plan of developing radioisotopes with a high power proton accelerator of the Neutron Science Project is presented. The status of production and utilization of radioisotopes in Japan is briefly discussed. The radioisotopes to be produced for biomedical use are discussed together with the facility for production of those radioisotopes and for research with the products. (author)

  5. Expected utility with lower probabilities

    DEFF Research Database (Denmark)

    Hendon, Ebbe; Jacobsen, Hans Jørgen; Sloth, Birgitte

    1994-01-01

    An uncertain and not just risky situation may be modeled using so-called belief functions assigning lower probabilities to subsets of outcomes. In this article we extend the von Neumann-Morgenstern expected utility theory from probability measures to belief functions. We use this theory...

  6. Utilities practices toward sustainable development

    International Nuclear Information System (INIS)

    2008-01-01

    The strategy toward a Sustainable Development is not standardised and it is useful to compare approaches of companies. WG C3.03 analysed a number of Sustainability Reports or Environmental Reports, published by Utilities, exposing their current approaches to the three 'Pillars': environmental aspects, society development and economical performances. Case studies, relevant to the three 'Pillars', show examples of practices

  7. Utilization and management of alder.

    Science.gov (United States)

    David G. Briggs; Dean S. DeBell; William A. Atkinson

    1978-01-01

    In the Pacific Northwest and British Columbia, red alder often grows on forest lands following natural or man-caused disturbances. Frequently ignored as a pest or weed, many alder stands have developed to the point where important utilization and management questions are being asked. It is recognized that alder is a fast growing species, and that its rapid early growth...

  8. Utility impact on STARFIRE design

    International Nuclear Information System (INIS)

    DeFreece, D.A.; Waganer, L.M.; Woklenhauer, W.C.

    1981-01-01

    A primary objective of STARFIRE has been to design a tokamak fusion power plant that was attractive to the utilities. To achieve this goal, several utility representatives were directly involved in the decision-making processes as the design evolved. An initial step was to establish the relative importance to the utilities for an extensive list of economic, performance, safety and environmental issues. The top twenty issues were ranked. Cost of electricity was clearly most important with very little spread in the ratings of individual evaluators. Licensing is a go/no-go factor and must be accomplished for the other factors to have meaning. The top nine factors were judged to be very important by all evaluators, as was shown by the spread of ratings from 5 to 10. There is considerably more spread in the bottom eleven, which reflects a lack of consensus as to the relative importance of the evaluation factors. This evaluation was utilized in establishing the initial design concept

  9. Utilizing Twitter for Concept Learning

    Science.gov (United States)

    Buzzelli, Armand; Holdan, E. Gregory; Rota, Daniel; McCarthy, John

    2016-01-01

    Despite the perception that face-to-face classrooms provide speaking opportunities, studies by Fassinger (1995), Nunn (1996), and Weimer (2013) have conveyed that there is limited interaction in a traditional college lecture setting. Social media networks such as Twitter provide an opportunity for instructors to utilize popular mobile technology…

  10. Thorium utilization in power reactors

    International Nuclear Information System (INIS)

    Saraceno; Marcos.

    1978-10-01

    In this work the recent (prior to Aug, 1976) literature on thorium utilization is reviewed briefly and the available information is updated. After reviewing the nuclear properties relevant to the thorium fuel cycle we describe briefly the reactor systems that have been proposed using thorium as a fertile material. (author) [es

  11. Manpower Utilization in Social Welfare.

    Science.gov (United States)

    Teare, Robert J.; McPheeters, Harold L.

    To study the problems of developing a useful conceptual framework for utilizing workers in the field of social welfare who received training at less than the highest professional level, four 2-day symposium sessions were held during the fall of 1968, Approximately 13 participants, predominanatly social workers and representatives from the fields…

  12. Wind energy utilization: A bibliography

    Science.gov (United States)

    1975-01-01

    Bibliography cites documents published to and including 1974 with abstracts and references, and is indexed by topic, author, organization, title, and keywords. Topics include: Wind Energy Potential and Economic Feasibility, Utilization, Wind Power Plants and Generators, Wind Machines, Wind Data and Properties, Energy Storage, and related topics.

  13. Bankruptcy games with nontransferable utility

    NARCIS (Netherlands)

    Dietzenbacher, Bas

    This paper analyzes bankruptcy games with nontransferable utility as a generalization of bankruptcy games with monetary payoffs. Following the game theoretic approach to NTU-bankruptcy problems, we study some appropriate properties and the core of NTU-bankruptcy games. Generalizing the core cover

  14. Bankruptcy Games with Nontransferable Utility

    NARCIS (Netherlands)

    Dietzenbacher, Bas

    2017-01-01

    This paper analyzes bankruptcy games with nontransferable utility as a generalization of bankruptcy games with monetary payoffs. Following the game theoretic approach to NTU-bankruptcy problems, we study some appropriate properties and the core of NTU-bankruptcy games. Generalizing the core cover

  15. Exotic statistics on surfaces

    International Nuclear Information System (INIS)

    Imbo, T.D.; March-Russel, J.

    1990-01-01

    We investigate the allowed spectrum of statistics for n identical spinless particles on an arbitrary closed two-manifold M, by using a powerful topological approach to the study of quantum kinematics. On a surface of genus g≥1 statistics other than Bose or Fermi can only be obtained by utilizing multi-component state vectors transforming as an irreducible unitary representation of the fundamental group of the n-particle configuration space. These multi-component (or nonscalar) quantizations allow the possibility of fractional statistics, as well as other exotic, nonfractional statistics some of whose properties we discuss. On an orientable surface of genus g≥0 only anyons with rational statistical parameter θ/π=p/q are allowed, and their number is restricted to be sq-g+1 (selement ofZ). For nonorientable surfaces only θ=0, π are allowed. Finally, we briefly comment on systems of spinning particles and make a comparison with the results for solitons in the O(3)-invariant nonlinear sigma model with space manifold M. (orig.)

  16. Power Sales to Electric Utilities

    Energy Technology Data Exchange (ETDEWEB)

    None

    1989-02-01

    The Public Utilities Regulatory Policies Act (PURPA) of 1979 requires that electrical utilities interconnect with qualifying facilities and purchase electricity at a rate based upon their full avoided costs (i.e., costs of providing both capacity and energy). Qualifying facilities (QF) include solar or geothermal electric units, hydropower, municipal solid waste or biomass-fired power plants, and cogeneration projects that satisfy maximum size, fuel use, ownership, location, and/or efficiency criteria. In Washington State, neither standard power purchase prices based upon a proxy ''avoided plant'', standard contracts, or a standard offer process have been used. Instead, a variety of power purchase contracts have been negotiated by developers of qualifying facilities with investor-owned utilities, public utility districts, and municipally-owned and operated utilities. With a hydro-based system, benefits associated with resource acquisition are determined in large part by how compatible the resource is with a utility's existing generation mix. Power purchase rates are negotiated and vary according to firm energy production, guarantees, ability to schedule maintenance or downtime, rights of refusal, power plant purchase options, project start date and length of contract; front-loading or levelization provisions; and the ability of the project to provide ''demonstrated'' capacity. Legislation was also enacted which allows PURPA to work effectively. Initial laws established ownership rights and provided irrigation districts, PUDs, and municipalities with expanded enabling powers. Financial processes were streamlined and, in some cases, simplified. Finally, laws were passed which are designed to ensure that development proceeds in an environmentally acceptable manner. In retrospect, PURPA has worked well within Washington. In the state of Washington, 20 small-scale hydroelectric projects with a combined generating capacity of

  17. Interactive Design of Developable Surfaces

    KAUST Repository

    Tang, Chengcheng

    2016-01-15

    We present a new approach to geometric modeling with developable surfaces and the design of curved-creased origami. We represent developables as splines and express the nonlinear conditions relating to developability and curved folds as quadratic equations. This allows us to utilize a constraint solver, which may be described as energy-guided projection onto the constraint manifold, and which is fast enough for interactive modeling. Further, a combined primal-dual surface representation enables us to robustly and quickly solve approximation problems.

  18. Urgensi Pencatatan Perkawinan (Perspektif Utilities

    Directory of Open Access Journals (Sweden)

    Dyah Ochtorina Susanti

    2017-01-01

    Full Text Available Pencatatan perkawinan merupakan kewajiban administratif berdasarkan peraturan perundang-undangan yang bertujuan untuk memberikan jaminan perlindungan, danuhan hak asasi manusia jika di kemudian hari timbul perbuatan hukum yang berimplikasi terjadinya akibat hukum sehingga dapat dibuktikan dengan bukti yang sempurna dengan suatu akta otentik sebagai suatu bentuk kepastian hukum. Penelitian ini bertujuan menemukan dan menganalisa serta memberikan pemahaman mengenai pentingnya pencatatan perkawinan dalam hukum positif Indonesia.. Hasil dari penelitian yang menggunakan metode yuridis normatif dengan pendekatan perundang-undangan, dan teori utilities (teori kemanfaatan ini memberikan penjelasan bahwa pencatatan perkawinan dilakukan guna memberi kemanfaatan yang sebesar-besarnya demi terciptanya kebahagiaan bagi banyak orang. Kata Kunci : Pencatatan, Perkawinan, Teori Utilities.

  19. Tattoo machines, needles and utilities.

    Science.gov (United States)

    Rosenkilde, Frank

    2015-01-01

    Starting out as a professional tattooist back in 1977 in Copenhagen, Denmark, Frank Rosenkilde has personally experienced the remarkable development of tattoo machines, needles and utilities: all the way from home-made equipment to industrial products of substantially improved quality. Machines can be constructed like the traditional dual-coil and single-coil machines or can be e-coil, rotary and hybrid machines, with the more convenient and precise rotary machines being the recent trend. This development has resulted in disposable needles and utilities. Newer machines are more easily kept clean and protected with foil to prevent crosscontaminations and infections. The machines and the tattooists' knowledge and awareness about prevention of infection have developed hand-in-hand. For decades, Frank Rosenkilde has been collecting tattoo machines. Part of his collection is presented here, supplemented by his personal notes. © 2015 S. Karger AG, Basel.

  20. Microorganism Utilization for Synthetic Milk

    Science.gov (United States)

    Morford, Megan A.; Khodadad, Christina L.; Caro, Janicce I.; Spencer, LaShelle E.; Richards, Jeffery T.; Strayer, Richard F.; Birmele, Michele N.; Wheeler, Raymond M.

    2014-01-01

    A desired architecture for long duration spaceflight, like aboard the International Space Station or for future missions to Mars, is to provide a supply of fresh food crops for the astronauts. However, some crops can create a high proportion of inedible plant waste. The main goal of the Synthetic Biology project, Cow in a Column, was to produce the components of milk (sugar, lipid, protein) from inedible plant waste by utilizing microorganisms (fungi, yeast, bacteria). Of particular interest was utilizing the valuable polysaccharide, cellulose, found in plant waste, to naturally fuel-through microorganism cellular metabolism- the creation of sugar (glucose), lipid (milk fat), and protein (casein) in order to produce a synthetic edible food product. Environmental conditions such as pH, temperature, carbon source, aeration, and choice microorganisms were optimized in the laboratory and the desired end-products, sugars and lipids, were analyzed. Trichoderma reesei, a known cellulolytic fungus, was utilized to drive the production of glucose, with the intent that the produced glucose would serve as the carbon source for milk fat production and be a substitute for the milk sugar lactose. Lipid production would be carried out by Rhodosporidium toruloides, yeast known to accumulate those lipids that are typically found in milk fat. Results showed that glucose and total lipid content were below what was expected during this phase of experimentation. In addition, individual analysis of six fatty acids revealed that the percentage of each fatty acid was lower than naturally produced bovine milk. Overall, this research indicates that microorganisms could be utilized to breakdown inedible solid waste to produce useable products. For future work, the production of the casein protein for milk would require the development of a genetically modified organism, which was beyond the scope of the original project. Additional trials would be needed to further refine the required

  1. Environmental impacts of energy utilization

    International Nuclear Information System (INIS)

    Prado, C.P.C. do; Orsini, C.M.Q.; Rodrigues, D.; Barolli, E.; Nogueira, F.R.; Bosco, F.A.R.; Tabacniks, M.H.; Artaxo Netto, P.E.

    1981-04-01

    A survey is done of the available data on the physical environmental impacts in Brazil, derived from energetic systems such as: petroleum, hydroelectricity, firewood, coal, ethanol, methanol and hydrogen. A critical evalution of these data is done with respect to the preservation of the environment. The necessity of studying the environmental impact of the utilization of ethanol, nuclear fuels and coal is stressed. (M.A.) [pt

  2. Strategy for utilizing nuclear power

    International Nuclear Information System (INIS)

    Martens, E.J.

    1977-01-01

    One of the national goals is to achieve independence in the area of energy supplies in the next few years. It is believed that attaining this goal will require extensive utilization of nuclear power in conventional fission reactors. It is proposed that the best way to develop the nuclear resource is through government ownership of the reactors. It is argued that this will minimize the risks associated with the nuclear-power option and clear the way for its exploitation

  3. FAIR VALUE: UTILITY AND LIMITS

    OpenAIRE

    Valentin Gabriel Cristea

    2015-01-01

    This paper presents the utility and the limits of the fair value. We believe that any new product must be tried and tested before being imposed on the market and must be accepted by all potential users and those who will be affected, directly or indirectly and its advantages, disadvantages, risks, its cost must be predetermined and analyzed in a comprehensive and objective.We ask: Do financial statements at fair value meet users' expectations? The requirement to use fair value pricing mode...

  4. Developing utility emergency preparedness exercises

    International Nuclear Information System (INIS)

    Sjoeblom, K.

    1986-01-01

    Utility emergency preparedness exercises constitute an important link in upgrading the response to nuclear power plant emergencies. Various emergency exercises are arranged annually at the Loviisa nuclear power plant. The on-site simulator is a practical tool in developing suitable accident scenarios and demonstrating them to the site emergency players and spectators. The exercises concentrate on emergency management and radiological activities. It is important to create a high degree of motivation. (author)

  5. Utilities practices toward sustainable development

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-01

    The strategy toward a Sustainable Development is not standardised and it is useful to compare approaches of companies. WG C3.03 analysed a number of Sustainability Reports or Environmental Reports, published by Utilities, exposing their current approaches to the three 'Pillars': environmental aspects, society development and economical performances. Case studies, relevant to the three 'Pillars', show examples of practices

  6. Selenium Utilization Strategy by Microalgae

    Directory of Open Access Journals (Sweden)

    Hiroya Araie

    2009-11-01

    Full Text Available The diversity of selenoproteins raises the question of why so many life forms require selenium. Selenoproteins are found in bacteria, archaea, and many eukaryotes. In photosynthetic microorganisms, the essential requirement for selenium has been reported in 33 species belonging to six phyla, although its biochemical significance is still unclear. According to genome databases, 20 species are defined as selenoprotein-producing organisms, including five photosynthetic organisms. In a marine coccolithophorid, Emiliania huxleyi (Haptophyta, we recently found unique characteristics of selenium utilization and novel selenoproteins using 75Se-tracer experiments. In E. huxleyi, selenite, not selenate, is the main substrate used and its uptake is driven by an ATP-dependent highaffinity, active transport system. Selenite is immediately metabolized to low-molecular mass compounds and partly converted to at least six selenoproteins, named EhSEP1–6. The most (EhSEP2 and second-most abundant selenoproteins (EhSEP1 are disulfide isomerase (PDI homologous protein and thioredoxin reductase (TR 1, respectively. Involvement of selenium in PDI is unique in this organism, while TR1 is also found in other organisms. In this review, we summarize physiological, biochemical, and molecular aspects of selenium utilization by microalgae and discuss their strategy of selenium utilization.

  7. Purchasing non-utility power

    International Nuclear Information System (INIS)

    Brackeen, L.G.

    1990-01-01

    The author discusses Houston Lighting and Power Company's procedure for purchasing power from cogenerators. By way of introduction, HL and P is the eighth largest electric utility in the United States in terms of kilowatt-hour sales and the second largest purchaser of natural gas in the nation. HL and P is also the principal utility providing electric service to the massive petrochemical industry in Southeast Texas. Of the 4,800 MW of cogeneration available, HL and P buys 945 MW under firm contracts, wheel 1,600 MW to other utilities, buy 400 MW under non-firm contracts and the balance is self-generation used to displace power which would otherwise be purchased from HL and P. With all this cogeneration capacity available, the problem until recently has been managing the surplus. HL and P now is finding itself in the unaccustomed position of needing to buy additional power or build plants to meet the modest growth it forecasts for Houston. The need for additional capacity coincides with the expiration of cogeneration contracts in 1993 and 1994. To meet this capacity need, they are determined to avoid buying cogeneration at a very high price and on delivery terms which do not reflect realistic benefits to their electric customers. The paper gives information on the background on PUC regulations and legislation, then briefly reviews the procedure for purchase of cogenerated power in Texas

  8. Simple utility functions with Giffen demand

    DEFF Research Database (Denmark)

    Sørensen, Peter Norman

    2007-01-01

    Simple utility functions with the Giffen property are presented: locally, the demand curve for a good is upward sloping. The utility functions represent continuous, monotone, convex preferences......Simple utility functions with the Giffen property are presented: locally, the demand curve for a good is upward sloping. The utility functions represent continuous, monotone, convex preferences...

  9. Promotion of HANARO Utilization for Year 2006

    Energy Technology Data Exchange (ETDEWEB)

    Sohn, J. M.; Kim, H. R.; Jun, B. J. (and others)

    2007-05-15

    To activate the HANARO utilization by expanding HANARO utilization fields, recruiting and training new users. In order to promote the HANARO utilization, the following activities have been performed. The neutron usage fee in HANARO. Achievements of HANARO utilization. Project for Activation of the Research using HANARO. HANARO Symposium. Survey of the HANARO User Satisfaction Index. Operation and Management of HANARO Server. Management of HANARO related committees. Training of HANARO users. Related activities of HANARO publicity. The related activities to activate HANARO utilization have been carried out successfully. This report summarized the detailed activities to activate the HANARO utilization. They will be useful for expanding HANARO utilization in the near future.

  10. Integrating photovoltaics into utility distribution systems

    International Nuclear Information System (INIS)

    Zaininger, H.W.; Barnes, P.R.

    1995-01-01

    Electric utility distribution system impacts associated with the integration of distributed photovoltaic (PV) energy sources vary from site to site and utility to utility. The objective of this paper is to examine several utility- and site-specific conditions which may affect economic viability of distributed PV applications to utility systems. Assessment methodology compatible with technical and economic assessment techniques employed by utility engineers and planners is employed to determine PV benefits for seven different utility systems. The seven case studies are performed using utility system characteristics and assumptions obtained from appropriate utility personnel. The resulting site-specific distributed PV benefits increase nonsite-specific generation system benefits available to central station PV plants as much as 46%, for one utility located in the Southwest

  11. Genetically tunable M13 phage films utilizing evaporating droplets.

    Science.gov (United States)

    Alberts, Erik; Warner, Chris; Barnes, Eftihia; Pilkiewicz, Kevin; Perkins, Edward; Poda, Aimee

    2018-01-01

    This effort utilizes a genetically tunable system of bacteriophage to evaluate the effect of charge, temperature and particle concentration on biomaterial synthesis utilizing the coffee ring (CR) effect. There was a 1.6-3 fold suppression of the CR at higher temperatures while maintaining self-assembled structures of thin films. This suppression was observed in phage with charged and uncharged surface chemistry, which formed ordered and disordered assemblies respectively, indicating CR suppression is not dependent on short-range ordering or surface chemistry. Analysis of the drying process suggests weakened capillary flow at elevated temperatures caused CR suppression and could be further enhanced for controlled assembly for advanced biomaterials. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

  12. Recent trend in coal utilization technology. Coal utilization workshop

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Chon Ho; Son, Ja Ek; Lee, In Chul; Jin, Kyung Tae; Kim, Seong Soo [Korea Inst. of Energy Research, Taejon (Korea, Republic of)

    1995-12-01

    The 11th Korea-U.S.A. joint workshop on coal utilization technology was held in somerset, Pennsylvania, U.S.A. from october 2 to 3, 1995. In the opening ceremony, Dr.C. Low-el Miller, associate deputy assistant secretary of office of clean coal technology, U.S.DOE, gave congratulatory remarks and Dr. Young Mok Son, president of KIER, made a keynote address. In this workshop, 30 papers were presented in the fields of emission control technology, advanced power generation systems, and advanced coal cleaning and liquid fuels. Especially, from the Korean side, not only KIER but also other private research institutes and major engineering companies including KEPCO, Daewoo Institute of Construction Technology, Jindo Engineering and Construction Co. Daewoo Institute for Advanced Engineering and universities participated in this workshop, reflecting their great interests. Attendants actively discussed about various coal utilization technologies and exchanged scientific and technical information on the state-of-art clean coal technologies under development. (author)

  13. Vision 2021. The utilities future

    Energy Technology Data Exchange (ETDEWEB)

    Liere, J. van [KEMA, Arnhem (Netherlands)

    1996-12-01

    The electricity industry is gradually making the transition to a free market economy characterized by competition. With the arrival of a more market-oriented structure, the electricity companies have taken measures to reduce costs while retaining reliability and safety of the production and distribution. Today the majority of these efforts are oriented towards optimizing the scope and the structure of the organizations and towards streamlining internal processes in order to improve productivity. Throughout the world, the increasing competition among utilities is accompanied by the unbundling of production, transport, distribution and customer service functions. There is a remarkable similarity between the transitions in the computer industry some years ago (from main frame to personal PC`s) and in the electric utility industry today. The new structure is expected to be less centralized and more dispersed. In the dispersed generation concept the locally deployed power plant must become smaller, more flexible, more efficient and less expensive than today`s power plants. Power generation is gradually changing from a steam cycle (Rankine cycle) via the combined cycle to the gas cycle (Brayton cycle). The fuel used to power the gas turbine is expected to change in the future from high calorific to low calorific gas, generated from biomass, waste, oil residues, blast furnaces, coal, etc. Five new areas to be addressed have been identified that can be characterized as follows: (a) improved utilization of capital-intensive production resources to reduce costs, (b) electrification and the supply of heat to increase sales and market share, (c) sustainable developments to broaden our future resource base, (d) improved efficiency based on the Brayton cycle to increase flexibility, (e) development of energy services with new secondary services to stay in the market. (EG) 10 refs.

  14. Surfaces of Building Practice

    OpenAIRE

    Surynková, Petra

    2009-01-01

    My diploma thesis Surfaces of Building Practice deals with the basic properties of surfaces, their mathematical description, categorization, and application in technical practice. Each studied surface is defined and its process of construction and parametrical description is listed. The thesis studies selected types of surfaces in details - these surfaces include surfaces of revolution, ruled surfaces, screw surfaces, and translational surfaces. An application of each studied surfaces is show...

  15. Iron oxide surfaces

    Science.gov (United States)

    Parkinson, Gareth S.

    2016-03-01

    was recently challenged and a new structure based on a thin film of Fe3O4(111) on α-Fe2O3(0001) was proposed. The merits of the competing models are discussed. The α-Fe2O3(1 1 bar02) "R-cut" surface is recommended as an excellent prospect for future study given its apparent ease of preparation and its prevalence in nanomaterial. In the latter sections the literature regarding adsorption on iron oxides is reviewed. First, the adsorption of molecules (H2, H2O, CO, CO2, O2, HCOOH, CH3OH, CCl4, CH3I, C6H6, SO2, H2S, ethylbenzene, styrene, and Alq3) is discussed, and an attempt is made to relate this information to the reactions in which iron oxides are utilized as a catalyst (water-gas shift, Fischer-Tropsch, dehydrogenation of ethylbenzene to styrene) or catalyst supports (CO oxidation). The known interactions of iron oxide surfaces with metals are described, and it is shown that the behaviour is determined by whether the metal forms a stable ternary phase with the iron oxide. Those that do not, (e.g. Au, Pt, Ag, Pd) prefer to form three-dimensional particles, while the remainder (Ni, Co, Mn, Cr, V, Cu, Ti, Zr, Sn, Li, K, Na, Ca, Rb, Cs, Mg, Ca) incorporate within the oxide lattice. The incorporation temperature scales with the heat of formation of the most stable metal oxide. A particular effort is made to underline the mechanisms responsible for the extraordinary thermal stability of isolated metal adatoms on Fe3O4 surfaces, and the potential application of this model system to understand single atom catalysis and sub-nano cluster catalysis is discussed. The review ends with a brief summary, and a perspective is offered including exciting lines of future research.

  16. Support for cold neutron utilization

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Kye Hong; Han, Young Soo; Choi, Sungmin; Choi, Yong; Kwon, Hoon; Lee, Kwang Hee

    2012-06-15

    - Support for experiments by users of cold neutron scattering instrument - Short-term training of current and potential users of cold neutron scattering instrument for their effective use of the instrument - International collaboration for advanced utilization of cold neutron scattering instruments - Selection and training of qualified instrument scientists for vigorous research endeavors and outstanding achievements in experiments with cold neutron - Research on nano/bio materials using cold neutron scattering instruments - Bulk nano structure measurement using small angle neutron scattering and development of analysis technique.

  17. FAIR VALUE: UTILITY AND LIMITS

    Directory of Open Access Journals (Sweden)

    Valentin Gabriel Cristea

    2015-05-01

    Full Text Available This paper presents the utility and the limits of the fair value. We believe that any new product must be tried and tested before being imposed on the market and must be accepted by all potential users and those who will be affected, directly or indirectly and its advantages, disadvantages, risks, its cost must be predetermined and analyzed in a comprehensive and objective.We ask: Do financial statements at fair value meet users' expectations? The requirement to use fair value pricing model that was carrying was not accompanied by a parallel examination of its impact on the presentation of accounts.

  18. Solar energy research and utilization

    Science.gov (United States)

    Cherry, W. R.

    1974-01-01

    The role of solar energy is visualized in the heating and cooling of buildings, in the production of renewable gaseous, liquid and solid fuels, and in the production of electric power over the next 45 years. Potential impacts of solar energy on various energy markets, and estimated costs of such solar energy systems are discussed. Some typical solar energy utilization processes are described in detail. It is expected that at least 20% of the U.S. total energy requirements by 2020 will be delivered from solar energy.

  19. Support for cold neutron utilization

    International Nuclear Information System (INIS)

    Lee, Kye Hong; Han, Young Soo; Choi, Sungmin; Choi, Yong; Kwon, Hoon; Lee, Kwang Hee

    2012-06-01

    - Support for experiments by users of cold neutron scattering instrument - Short-term training of current and potential users of cold neutron scattering instrument for their effective use of the instrument - International collaboration for advanced utilization of cold neutron scattering instruments - Selection and training of qualified instrument scientists for vigorous research endeavors and outstanding achievements in experiments with cold neutron - Research on nano/bio materials using cold neutron scattering instruments - Bulk nano structure measurement using small angle neutron scattering and development of analysis technique

  20. 236-Z canyon utilization study

    International Nuclear Information System (INIS)

    Dixon, D.R.

    1977-01-01

    The 236-Z canyon contains equipment for repurification of plutonium and recovery of plutonium from scrap material. To meet production requirements of Fast Flux Test Facility/Clinch River Breeder Reactor oxide with the existing plant, several new pieces of equipment will be needed in the future. More storage space and a better accountability system are needed to support this increased production. The available canyon space needs to be utilized to its fullest in order to accommodate the new equipment. The purpose of this document is to identify the new pieces of equipment, show how they fit into the flowsheet, and locate them in the canyon

  1. Evaluation of surface water treatment and discharge options for the Weldon Spring Site Remedial Action Project

    International Nuclear Information System (INIS)

    Goyette, M.L.; MacDonell, M.M.

    1992-01-01

    The US Department of Energy (DOE), under its Environmental Restoration and Waste Management Program, is responsible for conducting response actions at the Weldon Spring site in St. Charles County, Missouri. The site consists of two noncontiguous areas: (1) the chemical plant area, which includes four raffinate pits and two small ponds, and (2) a 3.6-ha (9-acre) quarry located about 6.4 km (4 mi) southwest of the chemical plant area. Both of these areas became chemically and radioactively contaminated as a result of processing and disposal activities that took place from the 1940s through 1960s. The Weldon Spring site, located about 48 km (30 mi) west of St. Louis, is listed on the National Priorities List of the US Environmental Protection Agency. Nitroaromatic explosives were processed by the Army at the chemical plant area during the 1940s, and radioactive materials were processed by DOE's predecessor agency (the Atomic Energy Commission) during the 1950s and 1960s. Overall remediation of the Weldon Spring site is being addressed through the Weldon Spring Site Remedial Action Project, and it consists of several components. One component is the management of radioactively and chemically contaminated surface water impoundments at the chemical plant area -- i.e., the four raffinate pits, Frog Pond, and Ash Pond which was addressed under a separate action and documented in an engineering evaluation/cost analysis report. This report discusses the evaluation of surface water treatment at the Weldon Spring site

  2. Enumeration of petroleum hydrocarbon utilizing bacteria

    International Nuclear Information System (INIS)

    Mukherjee, S.; Barot, M.; Levine, A.D.

    1996-01-01

    In-situ biological treatment is one among a number of emerging technologies that may be applied to the remediation of contaminated soils and groundwater. In 1985, a surface spill of 1,500 gallons of dielectric transformer oil at the Sandia National Laboratories (HERMES II facility) resulted in contamination of soil up to depths of 160 feet. The extent of contamination and site characteristics favored the application of in-situ bioremediation as a potential remedial technology. The purpose of this research was to enumerate indigenous microbial populations capable of degrading petroleum hydrocarbons. Microbial enumeration and characterization methods suitably adapted for hydrocarbon utilizing bacteria were used as an indicator of the presence of viable microbial consortia in excavated oil samples with hydrocarbon (TPH) concentrations ranging from 300 to 26,850 ppm. Microbial activity was quantified by direct and streak plating soil samples on silica gel media. Effects of toxicity and temperature were studied using batch cultures of hydrocarbon utilizing bacteria (selectively isolated in an enrichment medium), at temperatures of 20 and 35 C. It was concluded from this study that it is possible to isolate native microorganisms from contaminated soils from depths of 60 to 160 feet, and with oil concentration ranging from 300 to 26,850 ppm. About 62% of the microorganisms isolated form the contaminated soil were capable of using contaminant oil as a substrate for growth and metabolism under aerobic conditions. Growth rates were observed to be 50% higher for the highest contaminant concentration at 20 C. Resistance to toxicity to contaminant oil was also observed to be greater at 20 C than at 35 C

  3. Effective Charge Carrier Utilization in Photocatalytic Conversions.

    Science.gov (United States)

    Zhang, Peng; Wang, Tuo; Chang, Xiaoxia; Gong, Jinlong

    2016-05-17

    Continuous efforts have been devoted to searching for sustainable energy resources to alleviate the upcoming energy crises. Among various types of new energy resources, solar energy has been considered as one of the most promising choices, since it is clean, sustainable, and safe. Moreover, solar energy is the most abundant renewable energy, with a total power of 173 000 terawatts striking Earth continuously. Conversion of solar energy into chemical energy, which could potentially provide continuous and flexible energy supplies, has been investigated extensively. However, the conversion efficiency is still relatively low since complicated physical, electrical, and chemical processes are involved. Therefore, carefully designed photocatalysts with a wide absorption range of solar illumination, a high conductivity for charge carriers, a small number of recombination centers, and fast surface reaction kinetics are required to achieve a high activity. This Account describes our recent efforts to enhance the utilization of charge carriers for semiconductor photocatalysts toward efficient solar-to-chemical energy conversion. During photocatalytic reactions, photogenerated electrons and holes are involved in complex processes to convert solar energy into chemical energy. The initial step is the generation of charge carriers in semiconductor photocatalysts, which could be enhanced by extending the light absorption range. Integration of plasmonic materials and introduction of self-dopants have been proved to be effective methods to improve the light absorption ability of photocatalysts to produce larger amounts of photogenerated charge carriers. Subsequently, the photogenerated electrons and holes migrate to the surface. Therefore, acceleration of the transport process can result in enhanced solar energy conversion efficiency. Different strategies such as morphology control and conductivity improvement have been demonstrated to achieve this goal. Fine-tuning of the

  4. Supramolecular polymers as surface coatings: rapid fabrication of healable superhydrophobic and slippery surfaces.

    Science.gov (United States)

    Wei, Qiang; Schlaich, Christoph; Prévost, Sylvain; Schulz, Andrea; Böttcher, Christoph; Gradzielski, Michael; Qi, Zhenhui; Haag, Rainer; Schalley, Christoph A

    2014-11-19

    Supramolecular polymerization for non-wetting surface coatings is described. The self-assembly of low-molecular-weight gelators (LMWGs) with perfluorinated side chains can be utilized to rapidly construct superhydrophobic, as well as liquid-infused slippery surfaces within minutes. The lubricated slippery surface exhibits impressive repellency to biological li-quids, such as human serum and blood, and very fast self-healing. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Possibilities of utilizing power plant fly ashes

    Directory of Open Access Journals (Sweden)

    Mezencevová Andrea

    2003-09-01

    Full Text Available The burning of fossil fuels in industrial power stations plays a significant role in the production of thermal and electrical energy. Modern thermal power plants are producing large amounts of solid waste, mainly fly ashes. The disposal of power plant waste is a large environmental problem at the present time. In this paper, possibilities of utilization of power plant fly ashes in industry, especially in civil engineering, are presented. The fly ash is a heterogeneous material with various physical, chemical and mineralogical properties, depending on the mineralogical composition of burned coal and on the used combustion technology. The utilization of fly ashes is determined of their properties. The fineness, specific surface area, particle shape, density, hardness, freeze-thaw resistance, etc. are decisive. The building trade is a branch of industry, which employs fly ash in large quantities for several decades.The best utilization of fluid fly ashes is mainly in the production of cement and concrete, due to the excellent pozzolanic and cementitious properties of this waste. In the concrete processing, the fly ash is utilized as a replacement of the fine aggregate (fine filler or a partial replacement for cement (active admixture. In addition to economic and ecological benefits, the use of fly ash in concrete improves its workability and durability, increases compressive and flexural strength, reduces segregation, bleeding, shrinkage, heat evolution and permeability and enhances sulfate resistance of concrete.The aim of current research is to search for new technologies for the fly ash utilization. The very interesting are biotechnological methods to recovery useful components of fly ashes and unconventional methods of modification of fly ash properties such as hydrothermal zeolitization and mechanochemical modification of its properties. Mechanochemistry deals with physico - chemical transformations and chemical reactions of solids induced by

  6. Rough surface

    International Nuclear Information System (INIS)

    Hudina, M.

    1982-08-01

    For the determination of the thermal-hydraulic performances of rough surfaces, the method of evaluation is particularly important. In order to increase confidence in the results, a new evaluation procedure was introduced. This procedure is based on the transformation of simple channel experimental results to equal boundary conditions, and on the suitable application and confirmation of these transformed values in more complicated flow channel geometries. Existing methods, applied to the results obtained in an annular channel, do not fulfil all the transformation requirements. Thus a new, more complete transformation method, which uses the turbulent eddy diffusivity model, was developed. To check the quality of this transformation, within the scope of the new evaluation procedure, the results of experimental investigation in annular channels and in a bundle of hexagonal geometry were used together with the predictions of benchmark calculations. The success of the new method was confirmed by extensive comparisons, with the results of different presently-acknowledged transformations being considered as well. Based on these comparisons an assessment of the individual transformations is given. (Auth.)

  7. Utilizing inheritance in requirements engineering

    Science.gov (United States)

    Kaindl, Hermann

    1994-01-01

    The scope of this paper is the utilization of inheritance for requirements specification, i.e., the tasks of analyzing and modeling the domain, as well as forming and defining requirements. Our approach and the tool supporting it are named RETH (Requirements Engineering Through Hypertext). Actually, RETH uses a combination of various technologies, including object-oriented approaches and artificial intelligence (in particular frames). We do not attempt to exclude or replace formal representations, but try to complement and provide means for gradually developing them. Among others, RETH has been applied in the CERN (Conseil Europeen pour la Rechereche Nucleaire) Cortex project. While it would be impossible to explain this project in detail here, it should be sufficient to know that it deals with a generic distributed control system. Since this project is not finished yet, it is difficult to state its size precisely. In order to give an idea, its final goal is to substitute the many existing similar control systems at CERN by this generic approach. Currently, RETH is also tested using real-world requirements for the Pastel Mission Planning System at ESOC in Darmstadt. First, we outline how hypertext is integrated into a frame system in our approach. Moreover, the usefulness of inheritance is demonstrated as performed by the tool RETH. We then summarize our experiences of utilizing inheritance in the Cortex project. Lastly, RETH will be related to existing work.

  8. Kyoto : implications for utility regulation

    International Nuclear Information System (INIS)

    Dunsky, P.

    2003-01-01

    The author provided a historical perspective of energy use and the role of carbon in the western hemisphere by displaying a series of graphs showing carbon intensity of energy, carbon emissions from energy, and the long path to green power. The 1990s represented a decade of progress. Almost three times as much wind capacity as nuclear capacity was added worldwide in 2001. The main challenge for the 21st century will be to bring under-developed countries into the fold while perpetuating the economic and human progress of the twentieth century. It was emphasized that environmental damage caused by utilities must be reversed. The contemporary context for the Kyoto Protocol was reviewed. Canada's commitment under the Kyoto Protocol is to reduce greenhouse gas emissions by 6 per cent below 1990 levels. The challenge for utility regulators to meet this commitment was examined. The costs are not entirely excessive. Some of the regulatory issues were discussed, namely revising a broad rate making framework, cost recovery and others. The Kyoto compliance plan was also reviewed with reference to internal options, external options, identification of regulatory barriers, and consideration of greenhouse gas credit markets. figs

  9. Constraints to increased sludge utilization

    International Nuclear Information System (INIS)

    Pound, C.E.; Bory, L.D.

    1979-01-01

    The management and disposition of municipal sewage sludge is a growing problem as secondary treatment plants are completed to meet Clean Water Act standards. The prohibition of ocean dumping, the increased cost and difficulty to secure and operate sludge landfills, and the high energy costs of dewatering and incineration should all contribute to an increase in land application. However, land application and other beneficial use alternatives, such as give away/sale, account for only 20% of the 12 m/day tons of sludge produced nationally. This result can in part be attributed to public health, institutional, and legal constraints on implementing land application systems. Public health constraints include contaminants in sludge which may pose a risk to human health. Much current controversy about the safety of applying sludge to agricultural land on which food chain crops are grown focuses on heavy metals, especially cadmium. But proposed federal and state regulation of cadmium concentrations in sludge, at levels where human health risk has not been demonstrated, may limit utilization by land application. State operating rules and other administrative controls over sludge application are among the institutional constraints. Since land is an essential element in a land application system, securing adequate and suitable land involves legal constraints. Involuntary acquisition and zoning procedures can delay and frustrate land application programs. Securing indemnity insurance for possible damage to land to which sludge is applied has also been an obstacle to implementation of utilization programs

  10. Chinese Manned Space Utility Project

    Science.gov (United States)

    Gu, Y.

    Since 1992 China has been carrying out a conspicuous manned space mission A utility project has been defined and created during the same period The Utility Project of the Chinese Manned Space Mission involves wide science areas such as earth observation life science micro-gravity fluid physics and material science astronomy space environment etc In the earth observation area it is focused on the changes of global environments and relevant exploration technologies A Middle Revolution Image Spectrometer and a Multi-model Micro-wave Remote Sensor have been developed The detectors for cirrostratus distribution solar constant earth emission budget earth-atmosphere ultra-violet spectrum and flux have been manufactured and tested All of above equipment was engaged in orbital experiments on-board the Shenzhou series spacecrafts Space life science biotechnologies and micro-gravity science were much concerned with the project A series of experiments has been made both in ground laboratories and spacecraft capsules The environmental effect in different biological bodies in space protein crystallization electrical cell-fusion animal cells cultural research on separation by using free-low electrophoresis a liquid drop Marangoni migration experiment under micro-gravity as well as a set of crystal growth and metal processing was successfully operated in space The Gamma-ray burst and high-energy emission from solar flares have been explored A set of particle detectors and a mass spectrometer measured

  11. Managing change in nuclear utilities

    International Nuclear Information System (INIS)

    2001-07-01

    The nuclear power industry has undergone change since inception, but never so much as now. The rewards for proactively changing in anticipation of emerging demands are great, but the cost of failure is also great. Today nuclear plants are being shut down by socio-political and economic processes. The survival of the technology as a clean energy source for the future depends on the demonstration of long term safety to the public, protection of the environment, and economic superiority to competing energy sources. The overriding influence on these factors is strong management of the business with effective regulation. In particular it is necessary for both utility and regulator to believe that enhancing safety is part of being successful. This publication has been developed for all levels of management who are developing and implementing changes within their areas of responsibility. The safety conscious, continuous improvement, management culture, which has proven successful in today's nuclear business, has taken time to develop. Many utilities have difficulty sustaining this culture during the transitions that are intrinsic to change. Properly managed however, changes can enhance nuclear safety, plant reliability and cost competitiveness, from the design stage to decommissioning. Change has no respect for timing and regardless of the level of experience managers may have in its management, large scale change is confronting every nuclear utility world wide. These take the form of government policy changes, open market demands, privatization with the demand for increased shareholder returns, regulatory and social pressures, and economic and political transition. The danger from such issues for the nuclear company executive and the regulator is that they are powerful distractions, particularly for those executives who are not experienced in the unique managerial requirements of the nuclear business. This report gathers the experience of Member States into an array of

  12. NNP-LANL Utilities - Condition Assessment and Project Approach

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, Grant Lorenz [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-11-21

    This report is a presentation on LANL Utilities & Transportation Asset Management; Utility Assets Overview; Condition Assessment; Utilities Project Nominations & Ranking; and Utilities Project Execution.

  13. New record in peat utilization

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    Increment of peat utilization that started in 1990 continued also in 1991, due to which new record was achieved. Peat delivery increased 11.2 % from 16.1 million m 3 in 1990 to 17.9 million m 3 in 1991. The portion of energy peat was 16.4 million m 3 , and the portion of peat for other purposes 1.5 million m 3 . The energy content of fuel peat was 15.8 TWh, of which 13.8 TWh was milled peat and 2.0 TWh sod peat. The main portion of energy peat was used in communal back-pressure power plants for production of electricity and district heat. The second largest utilizer was industry. The rests 0.3 TWh (2 %) was delivered to private small scale utilization and export. About 88 000 MWh of sod peat was exported to Sweden. The portion of horticultural peat of the peat delivered for other purposes than energy production was 662 000 m 3 , of which only 260 000 m 3 was used in Finland and 408 000 m 3 was exported. Agriculture is the main user of peat outside the energy production. Weakly humified peat was used as litter and as absorber for slurrified manure about 286 000 m 3 . The value of the deliveries of peat industry exeeded 800 million FIM, of which the portion of milled peat was about 650 million FIM, the portion of sod peat about 95 million FIM, and the portion of domestic deliveries of horticultural peat 30 million FIM. The export of peat was 36 million FIM. Peat production in 1991 was 10.605 million m 3 , which is nearly a half of the production of 1990. The decrease was caused by both poor weather of may-june 1991 and the large peat supplies from the year 1990. About 60 % of the production target of 1991 was achieved. The production of sod peat increased by over 50 % from 736 000 m 3 in 1990 to 1 147 000 m 3 in 1991

  14. Capacity Utilization in European Railways

    DEFF Research Database (Denmark)

    Khadem Sameni, Melody; Landex, Alex

    2013-01-01

    At the strategic level, railways currently use different indices to estimate how ‘value’ is generated by using railway capacity. However, railway capacity is a multidisciplinary area, and attempts to develop various indices cannot provide a holistic measure of operational efficiency. European...... and unprecedented approach for this aim. Relative operational efficiency of 24 European railways in capacity utilization is studied for the first time by data envelopment analysis (DEA). It deviates from previous applications of DEA in the railway industry that are conducted to analyze cost efficiency of railways...... aspects of railway services in European countries has recently been quantified by European commission and are used for the first time in the literature. Invaluable insights can be inferred from the results which can provide a ground basis for railway practitioners and policy makers....

  15. The EURS (European utilities requirements)

    International Nuclear Information System (INIS)

    Berbey, P.

    2000-01-01

    The major European electricity producers have worked on a common requirement document for future LWR plants since 1992 to get specifications acceptable together by the owners, the public and the authorities. Thus the designers can develop standard LWR designs that could be acceptable everywhere in Europe and the utilities can open their consultations to vendors on common bases. Public and authority's acceptance should be improved as well. Significant saving are expected in development and construction costs. Since the release of the last versions of the EUR texts in 1996, a lot of work has been carried out: reviews by the regulators and other external organisations, comparisons, assessment of compliance of designs vs. EUR and clarification works on the controversial topics that deserved changes or clarification. At the beginning of 1999 enough material was available to start a complete revision of the EUR document

  16. Utility unbundling : large consumer's perspective

    International Nuclear Information System (INIS)

    Block, C.

    1997-01-01

    The perspectives of Sunoco as a large user of electric power on utility unbundling were presented. Sunoco's Sarnia refinery runs up an energy bill of over $60 million per year for electricity, natural gas (used both as a feedstock as well as a fuel), natural gas liquids and steam. As a large customer Sunoco advocates unbundling of all services, leaving only the 'pipes and wires' as true monopolies. In their view, regulation distorts the market place and prevents the lower prices that would result from competition as has been seen in the airline and telephone industries. Sunoco's expectation is that in the post-deregulated environment large and small consumers will have a choice of energy supplier, and large consumers will increasingly turn to co-generation as the most desirable way of meeting their power needs

  17. Utility library for structural bioinformatics.

    Science.gov (United States)

    Gront, Dominik; Kolinski, Andrzej

    2008-02-15

    In this Note we present a new software library for structural bioinformatics. The library contains programs, computing sequence- and profile-based alignments and a variety of structural calculations with user-friendly handling of various data formats. The software organization is very flexible. Algorithms are written in Java language and may be used by Java programs. Moreover the modules can be accessed from Jython (Python scripting language implemented in Java) scripts. Finally, the new version of BioShell delivers several utility programs that can do typical bioinformatics task from a command-line level. Availability The software is available for download free of charge from its website: http://bioshell.chem.uw.edu.pl. This website provides also numerous examples, code snippets and API documentation.

  18. News technology utilization fossil fuel

    Directory of Open Access Journals (Sweden)

    Blišanová Monika

    2004-09-01

    Full Text Available Fossil fuel – “alternative energy“ is coal, petroleum, natural gas. Petroleum and natural gas are scarce resources, but they are delimited. Reserves petroleum will be depleted after 39 years and reserves natural gas after 60 years.World reserves coal are good for another 240 years. Coal is the most abundant fossil fuel. It is the least expensive energy source for generating electricity. Many environmental problems associated with use of coal:in coal production, mining creates environmental problems.On Slovakia representative coal only important internal fuel – power of source and coal is produced in 5 locality. Nowadays, oneself invest to new technology on utilization coal. Perspective solution onself shows UCG, IGCC.

  19. Deprival value: information utility analysis

    Directory of Open Access Journals (Sweden)

    Marco Antonio Pereira

    Full Text Available ABSTRACT This article contributes to the perception that the users’ learning process plays a key role in order to apply an accounting concept and this involves a presentation that fits its informative potential, free of previous accounting fixations. Deprival value is a useful measure for managerial and corporate purposes, it may be applied to the current Conceptual Framework of the International Accounting Standards Board (IASB. This study analyzes its utility, taking into account cognitive aspects. Also known as value to the business, deprival value is a measurement system that followed a path where it was misunderstood, confused with another one, it faced resistance to be implemented and fell into disuse; everything that a standardized measurement method tries to avoid. In contrast, deprival value has found support in the academy and in specific applications, such as those related to the public service regulation. The accounting area has been impacted by sophistication of the measurement methods that increasingly require the ability to analyze accounting facts on an economic basis, at the risk of loss of their information content. This development becomes possible only when the potential of a measurement system is known and it is feasible to be achieved. This study consists in a theoretical essay based on literature review to discuss its origin, presentation, and application. Considering the concept’s cognitive difficulties, deprival value was analyzed, as well as its corresponding heteronym, value to the business, in order to explain some of these changes. The concept’s utility was also explored through cross-analysis with impairment and the scheme developed was applied to actual economic situations faced by a company listed on stock exchange.

  20. Utilization of nuclear research reactors

    International Nuclear Information System (INIS)

    1980-01-01

    Full text: Report on an IAEA interregional training course, Budapest, Hungary, 5-30 November 1979. The course was attended by 19 participants from 16 Member States. Among the 28 training courses which the International Atomic Energy Agency organized within its 1979 programme of technical assistance was the Interregional Training Course on the Utilization of Nuclear Research Reactors. This course was held at the Nuclear Training Reactor (a low-power pool-type reactor) of the Technical University, Budapest, Hungary, from 5 to 30 November 1979 and it was complemented by a one-week Study Tour to the Nuclear Research Centre in Rossendorf near Dresden, German Democratic Republic. The training course was very successful, with 19 participants attending from 16 Member States - Bangladesh, Bolivia, Czechoslovakia, Ecuador, Egypt, India, Iraq, Korean Democratic People's Republic, Morocco, Peru, Philippines, Spain, Thailand, Turkey, Vietnam and Yugoslavia. Selected invited lecturers were recruited from the USA and Finland, as well as local scientists from Hungarian institutions. During the past two decades or so, many research reactors have been put into operation around the world, and the demand for well qualified personnel to run and fully utilize these facilities has increased accordingly. Several developing countries have already acquired small- and medium-size research reactors mainly for isotope production, research in various fields, and training, while others are presently at different stages of planning and installation. Through different sources of information, such as requests to the IAEA for fellowship awards and experts, it became apparent that many research reactors and their associated facilities are not being utilized to their full potential in many of the developing countries. One reason for this is the lack of a sufficient number of trained professionals who are well acquainted with all the capabilities that a research reactor can offer, both in research and

  1. Utility Energy Services Contracts Lessons Learned

    Energy Technology Data Exchange (ETDEWEB)

    None

    2001-08-01

    This document describes best practices in the use of Utility Energy Services Contracts. The recommendations were generated by a group of innovative energy managers in many successful projects. The topics include project financing, competition between utility franchises, and water conservation.

  2. Utility Bill Insert for Wastewater Services

    Science.gov (United States)

    Intended for use by wastewater and water supply utilities, one side of the utility bill insert has information for customers that discharge to sanitary sewer systems; the other side is for customers with septic systems.

  3. Operating Room Utilization at Frederick Memorial Hospital

    National Research Council Canada - National Science Library

    Edwards, Jonathan A

    2007-01-01

    .... A logistical regression analysis was used to identify the impact of variables on operating room utilization rates and therefore help explain how or why some operating rooms incurred higher utilization rates than others...

  4. Utility installation review system : implementation report.

    Science.gov (United States)

    2009-03-01

    Each year, the Texas Department of Transportation (TxDOT) issues thousands of approvals that enable new : utility installations to occupy the state right of way (ROW). The current utility installation review process : relies on the physical delivery ...

  5. Utility Energy Services Contracts: Enabling Documents

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Karen; Vasquez, Deb

    2017-01-01

    The Federal Energy Management Program's 'Utility Energy Service Contracts: Enabling Documents' provide legislative information and materials that clarify the authority for federal agencies to enter into utility energy service contracts, or UESCs.

  6. BARRIER ISSUES TO THE UTILIZATION OF BIOMASS

    Energy Technology Data Exchange (ETDEWEB)

    Jay R. Gunderson; Bruce C. Folkedahl; Darren D. Schmidt; Greg F. Weber; Christopher J. Zygarlicke

    2002-05-01

    The Energy & Environmental Research Center (EERC) is conducting a project to examine the fundamental issues limiting the use of biomass in small industrial steam/power systems in order to increase the future use of this valuable domestic resource. Specifically, the EERC is attempting to elucidate the ash-related problems--grate clinkering and heat exchange surface fouling--associated with cofiring coal and biomass in grate-fired systems. Utilization of biomass in stoker boilers designed for coal can be a cause of concern for boiler operators. Boilers that were designed for low-volatile fuels with lower reactivities can experience damaging fouling when switched to higher-volatile and more reactive lower-rank fuels, such as when cofiring biomass. Higher heat release rates at the grate can cause more clinkering or slagging at the grate because of higher temperatures. Combustion and loss of volatile matter can start too early with biomass fuels compared to design fuel, vaporizing alkali and chlorides which then condense on rear walls and heat exchange tube banks in the convective pass of the boiler, causing noticeable increases in fouling. In addition, stoker-fired boilers that switch to biomass blends may encounter new chemical species such as potassium sulfates and various chlorides in combination with different flue gas temperatures because of changes in fuel heating value, which can adversely affect ash deposition behavior.

  7. The zebra mussel: US utility implications

    International Nuclear Information System (INIS)

    McMahon, R.F.

    1990-11-01

    Dreissena polymorpha, the freshwater macrofouling zebra mussel, was introduced to Lake St. Clair, near Detroit, Michigan, in 1985. It has since spread throughout Lake Erie. Its planktonic veliger larval stage disperses on water currents and adults are transported by human and natural vectors, making it likely to spread throughout most of the United States and southern Canada except for the southwestern and southern United State, where summer water temperatures are above tolerated levels. Veligers enter raw water systems on intake currents to settle and grow to adults attached by secreted byssal threads to hard surfaces. Accumulations of adults impede flow, aggravate sedimentation and corrosion, and foul small-diameter components. Settlement occurs at flow velocities less than 1.5--2.0 m/sec. Mussels can reduce effective pipe diameters and foul intake structures, steam condensers, heat exchangers, fire protection systems, and cooling tower basins. Establishment of mussels in raw water systems should be prevented because subsequent removal is difficult and expensive. Mitigation procedures include manual removal, robotic cleaning, thermal backwashing, water jetting, application of molluscicides, and possibly line pigging and acidic chemical cleaning. Control technologies include oxidizing and non-oxidizing molluscicides, robotic cleaning, shell strainers, exposure of veligers to high voltage electrical fields, thermal backwashing and sand-filtration. The United States power industry can utilize extensive European experience with this species and domestic experience with the Asian clam in its development of effective controls for zebra mussel fouling

  8. Urban ecology and the municipal utilities

    DEFF Research Database (Denmark)

    Nielsen, Susanne Balslev

    1998-01-01

    Current management of municipal utilities for energy, water and solid waste is often in conflict with the ideas of ecological demonstrationprojects. The writer argue there is a need of transformation within municipal utilities and a need of new planning tools......Current management of municipal utilities for energy, water and solid waste is often in conflict with the ideas of ecological demonstrationprojects. The writer argue there is a need of transformation within municipal utilities and a need of new planning tools...

  9. Enhanced methanol utilization in direct methanol fuel cell

    Science.gov (United States)

    Ren, Xiaoming; Gottesfeld, Shimshon

    2001-10-02

    The fuel utilization of a direct methanol fuel cell is enhanced for improved cell efficiency. Distribution plates at the anode and cathode of the fuel cell are configured to distribute reactants vertically and laterally uniformly over a catalyzed membrane surface of the fuel cell. A conductive sheet between the anode distribution plate and the anodic membrane surface forms a mass transport barrier to the methanol fuel that is large relative to a mass transport barrier for a gaseous hydrogen fuel cell. In a preferred embodiment, the distribution plate is a perforated corrugated sheet. The mass transport barrier may be conveniently increased by increasing the thickness of an anode conductive sheet adjacent the membrane surface of the fuel cell.

  10. A flexible micro biofuel cell utilizing hydrogel containing ascorbic acid

    Science.gov (United States)

    Goto, Hideaki; Fukushi, Yudai; Nishioka, Yasushiro

    2014-11-01

    This paper reports on a biofuel cell with a dimension of 13×24 mm2 fabricated on a flexible polyimide substrate. I its porous carbon-coated platinum (Pt) electrodes of 3 mm in width and 10 mm in length were fabricated using photolithography and screen printing techniques. Porous carbon was deposited by screen printing of carbon black ink on the Pt electrode surfaces in order to increase the effective electrode surface area and to absorb more enzymes on the electrode surfaces. It utilizes a solidified ascorbic acid (AA) aqueous solution in an agarose hydrogel to increase the portability. The maximum power and power density for the biofuel cell with the fuel unit containing 100 mM AA were 0.063 μW and 0.21 μW/cm2 at 0.019 V, respectively.

  11. A flexible micro biofuel cell utilizing hydrogel containing ascorbic acid

    International Nuclear Information System (INIS)

    Goto, Hideaki; Fukushi, Yudai; Nishioka, Yasushiro

    2014-01-01

    This paper reports on a biofuel cell with a dimension of 13×24 mm 2 fabricated on a flexible polyimide substrate. I its porous carbon-coated platinum (Pt) electrodes of 3 mm in width and 10 mm in length were fabricated using photolithography and screen printing techniques. Porous carbon was deposited by screen printing of carbon black ink on the Pt electrode surfaces in order to increase the effective electrode surface area and to absorb more enzymes on the electrode surfaces. It utilizes a solidified ascorbic acid (AA) aqueous solution in an agarose hydrogel to increase the portability. The maximum power and power density for the biofuel cell with the fuel unit containing 100 mM AA were 0.063 μW and 0.21 μW/cm 2 at 0.019 V, respectively

  12. 25 CFR 700.105 - Utility charges.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Utility charges. 700.105 Section 700.105 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES General Policies and Instructions Definitions § 700.105 Utility charges. Utility charges means the cost for heat...

  13. Trends in Utility Green Pricing Programs (2005)

    Energy Technology Data Exchange (ETDEWEB)

    Bird, L.; Brown, E.

    2006-10-01

    This report presents year-end 2005 data on utility green pricing programs, and examines trends in consumer response and program implementation over time. The data in this report, which were obtained via a questionnaire distributed to utility green pricing program managers, can be used by utilities to benchmark the success of their green power programs.

  14. Utilization of response surface for optimization of the production of a biosurfactant with application in the removal of petroleum-derived; Utilizacao de superficie de resposta para a otimizacao da producao de um biossurfactante com aplicacao na remocao de derivado de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Sarubbo, Leonie A.; Rufino, Raquel D.; Luna, Juliana M.; Farias, Charles B.B.; Santos, Valdemir A. dos [Universidade Catolica de Pernambuco (UNICAP), Recife, PE (Brazil)

    2012-07-01

    The surfactants, amphipathic compounds capable of reducing the surface tension of aqueous media, find application in many industries, especially in the petroleum, cosmetic and food, such as dispersants, emulsifiers and surfactants. With the necessity of environmental preservation, surfactants of micro-organisms origin, in substitution of synthetic surfactants, have become very attractive, since they are biodegradable and less toxic although their production costs are still high because of the substrates used and of the purification processes involved. Considering the need to reduce costs associated with the production of microbial surfactants, a strain of bacteria of the genus Pseudomonas, isolated from the port area was cultured in medium containing low-cost agro-industrial wastes, molasses and corn steep liquor, as substrates according a central composite rotatable design (CCRD) in order to evaluate the influence of independent variables molasses and corn steep liquor concentrations on the response variable surface tension. The biosurfactant was able to reduce the water surface tension from 71 mN / m to values around 27.5 mN / m. The dispersion ability and the capacity of oil removal of the surfactant was demonstrated. The possibility of application of biosurfactants in the remediation of oil polluted environments motivates the advancement of research to develop this technology for effective use in treatment of contaminated soils and waters. (author)

  15. Microwave assisted organic modification and surface functionalization of Phyllosilicates

    CSIR Research Space (South Africa)

    Kesavan Pillai, Sreejarani

    2012-11-01

    Full Text Available Organically modified phyllosilicates (montmorillonite and palygorskite) using Arquad 2HT-75 surfactant were effectively synthesized utilizing a microwave irradiation technique. The microwave method was successfully used also for the surface...

  16. Ecosystem of silicon utilizing organisms in the lost world

    Science.gov (United States)

    Das, S.

    2010-12-01

    It was Charles Darwin who first conceived the idea of “the Lost World” which spanned more than 80% of Earth History. This is about the rocks of the Precambrian period, in which Charles Darwin did not find any fossils during his study in 1859. Although Logan’s Foraminosphere and The Cyanosphere were the proposed concepts of the possible Precambrian life, however, these studies were flawed with non-biological artifacts, post-depositional contamination etc. Although now scientists believe the ‘hydrothermal cradle for life’ following the important studies in deep-sea vents, this is still a hypothetic view. All important experiments on the origin of life which were done with a reducing atmosphere, were also not correct. Scientists recently opined that probably life originated as silicon utilizing coacervates spontaneously in cosmos, and are transferred on the Earth in the Precambrian. These silicon utilizing coacervates could originate spontaneously in the Interstellar Medium (ISM) dust particles containing silicates with carbon, many organic molecules, and with mantles of ices. Thus ultraviolet ray from molecular hydrogen after collision excitation by electrons produced by cosmic-ray ionization may initiate seeds of life with formation of silicon utilizing coacervates; which are then scattered throughout the Universe. Similarly they can also originate in the GMCs, which have the clouds of dust and gases. These were also probably the last common ancestor (LCA) of all living creatures on the Earth. They are also still entering the surface of the Earth in small numbers during volcanic eruptions, blue lightning etc., but are quickly lost in the thickly inhabited Earth surface with ~ 1,00,000 diversified earthly species. These coacervates showed a direct correlation with non-cultivable spherical clusters found in the stratosphere, and the unknown spheroid bodies in microfossils ( ~ 3,200 Ma to >3,700 Ma) recovered in Australia, Africa and in Greenland. Both

  17. Method for aluminium dross utilization

    International Nuclear Information System (INIS)

    Lucheva, B.; Petkov, R.; Tzonev, Tz.

    2003-01-01

    A new hydrometallurgical method has been developed for metal aluminum utilization from secondary aluminum dross. Secondary aluminum dross is a powder product with an average of 35% aluminium content (below 1mm). It is waste from primary aluminum dross pyrometallurgical flux less treatment in rotary DC electric arc furnace. This method is based on aluminum leaching in copper chloride water solution. As a result an aluminum oxychloride solution and solids, consisting of copper and oxides are obtained. In order to copper chloride solution regenerate hydrochloric acid is added to the solids. The process is simple, quick, economic and safe. The aluminum oxychloride solution contains 56 g/l Al 2 O 3 . The molar ratios are Al:Cl=0,5; OH:Al=1. The solution has 32 % basicity and 1,1 g/cm 3 density. For increasing the molar ratio of aluminium to chlorine aluminum hydroxide is added to this solution at 80 o C. Aluminum hydroxide is the final product from the secondary aluminum dross alkaline leaching. As a result aluminum oxychloride solution of the following composition is prepared: Al 2 O 3 - 180 g/l; Al:Cl=1,88; OH:Al=4,64; basicity 82%; density 1,22 g/cm 3 , pH=4 -4,5. Aluminum oxychloride solution produced by means of this method can be used in potable and wastewater treatment, paper making, in refractory mixture as a binder etc. (Original)

  18. Geology in coal resource utilization

    International Nuclear Information System (INIS)

    Peters, D.C.

    1991-01-01

    The 37 papers in this book were compiled with an overriding theme in mind: to provide the coal industry with a comprehensive source of information on how geology and geologic concepts can be applied to the many facets of coal resource location, extraction, and utilization. The chapters have been arranged to address the major coal geology subfields of Exploration and Reserve Definition, Reserve Estimation, Coalbed Methane, Underground Coal Gasification, Mining, Coal Quality Concerns, and Environmental Impacts, with papers distributed on the basis of their primary emphasis. To help guide one through the collection, the author has included prefaces at the beginning of each chapter. They are intended as a brief lead-in to the subject of the chapter and an acknowledgement of the papers' connections to the subject and contributions to the chapter. In addition, a brief cross-reference section has been included in each preface to help one find papers of interest in other chapters. The subfields of coal geology are intimately intertwined, and investigations in one area may impact problems in another area. Some subfields tend to blur at their edges, such as with reserve definition and reserve estimation. Papers have been processed separately for inclusion on the data base

  19. Electric utilities and clean air

    International Nuclear Information System (INIS)

    Evans, J.E.

    1991-01-01

    This paper reports that electricity has become essential to American life. Approximately 70 percent of the nation's electricity is produced by burning fossil fuels, with coal, the most abundant, domestically-available, extracted natural resource, providing over 55 percent of the total electricity consumed. Emissions resulting from the burning of fossil fuels are regulated by both the federal and state governments. In 1970, Congress passed the comprehensive Clean Air Act which established a national program to protect the nation's air quality. In 1977, additional strict regulations were passed, which mandated even more stringent emission controls for factories, power plants and auto emissions. Prior to passage of the Clean Air Act of 1990, utilities were required to adhere to three major types of clean air regulations: National Ambient Air Quality Standards (NAAQS), New Source Performance Standards (NSPS), and Prevention of Significant Deterioration (PSD) review. NAAQS established limits for the maximum concentration levels of specific air pollutants in the ambient atmosphere. For example, for an area to be in compliance with the NAAQS for sulfur dioxide (SO 2 ), its annual average SO 2 concentration must not exceed 0.03 ppm of SO 2 and a peak 24 hour level of 0.14 ppm of SO 2 must not be exceeded more than once per year

  20. Celss nutrition system utilizing snails

    Science.gov (United States)

    Midorikawa, Y.; Fujii, T.; Ohira, A.; Nitta, K.

    At the 40th IAF Congress in Malaga, a nutrition system for a lunar base CELSS was presented. A lunar base with a total of eight crew members was envisaged. In this paper, four species of plants—rice, soybean, lettuce and strawberry—were introduced to the system. These plants were sufficient to satisfy fundamental nutritional needs of the crew members. The supply of nutrition from plants and the human nutritional requirements could almost be balanced. Our study revealed that the necessary plant cultivation area per crew member would be nearly 40 m 3 in the lunar base. The sources of nutrition considered in the study were energy, sugar, fat, amino acids, inorganic salt and vitamins; however, calcium, vitamin B 2, vitamin A and sodium were found to be lacking. Therefore, a subsystem to supply these elements is of considerable value. In this paper, we report on a study for breeding snails and utilizing meat as food. Nutrients supplied from snails are shown to compensate for the abovementioned lacking elements. We evaluate the snail breeder and the associated food supply system as a subsystem of closed ecological life support system.

  1. Domestic utility attitudes toward foreign uranium supply

    International Nuclear Information System (INIS)

    1981-06-01

    The current embargo on the enrichment of foreign-origin uranium for use in domestic utilization facilities is scheduled to be removed in 1984. The pending removal of this embargo, complicated by a depressed worldwide market for uranium, has prompted consideration of a new or extended embargo within the US Government. As part of its on-going data collection activities, Nuclear Resources International (NRI) has surveyed 50 domestic utility/utility holding companies (representing 60 lead operator-utilities) on their foreign uranium purchase strategies and intentions. The most recent survey was conducted in early May 1981. A number of qualitative observations were made during the course of the survey. The major observations are: domestic utility views toward foreign uranium purchase are dynamic; all but three utilities had some considered foreign purchase strategy; some utilities have problems with buying foreign uranium from particular countries; an inducement is often required by some utilities to buy foreign uranium; opinions varied among utilities concerning the viability of the domestic uranium industry; and many utilities could have foreign uranium fed through their domestic uranium contracts (indirect purchases). The above observations are expanded in the final section of the report. However, it should be noted that two of the observations are particularly important and should be seriously considered in formulation of foreign uranium import restrictions. These important observations are the dynamic nature of the subject matter and the potentially large and imbalanced effect the indirect purchases could have on utility foreign uranium procurement

  2. Fundamental study of low-NOx combustion fly ash utilization

    International Nuclear Information System (INIS)

    Suuberg, Eric M.; Hurt, Robert H.

    1998-01-01

    This study is principally concerned with characterizing the organic part of coal combustion fly ashes. High carbon fly ashes are becoming more common as by-products of low-NOx combustion technology, and there is need to learn more about this fraction of the fly ash. The project team consists of two universities, Brown and Princeton, and an electrical utility, New England Power. A sample suite of over fifty fly ashes has been gathered from utilities across the United States, and includes ashes from a coals ranging in rank from bituminous to lignite. The characterizations of these ashes include standard tests (LOI, Foam Index), as well as more detailed characterizations of their surface areas, porosity, extractability and adsorption behavior. The ultimate goal is, by better characterizing the material, to enable broadening the range of applications for coal fly ash re-use beyond the current main market as a pozzolanic agent for concretes. The potential for high carbon-content fly ashes to substitute for activated carbons is receiving particular attention. The work performed to date has already revealed how very different the surfaces of different ashes produced by the same utility can be, with respect to polarity of the residual carbon. This can help explain the large variations in acceptability of these ashes as concrete additives

  3. Equity implications of utility energy conservation programs

    Energy Technology Data Exchange (ETDEWEB)

    Sutherland, R.J.

    1994-03-15

    This paper uses the Residential Energy Consumption Survey undertaken by the Energy Information Administration in 1990 to estimate the statistical association between household income and participation in electric utility energy conservation programs and the association between participation and the electricity consumption. The results indicate that utility rebates, energy audits, load management programs and other conservation measures tend to be undertaken at greater frequency by high income households than by low income households. Participants in conservation programs tend to occupy relatively new and energy efficient residences and undertake conservation measures other than utility programs, which suggests that utility sponsored programs are substitutes for other conservation investments. Electricity consumption during 1990 is not significantly less for households participating in utility programs than for nonparticipants, which also implies that utility conservation programs are displacing other conservation investments. Apparently, utility programs are not avoiding costs of new construction and instead are transferring wealth, particularly to high income participating households.

  4. Electric utility companies and geothermal power

    Science.gov (United States)

    Pivirotto, D. S.

    1976-01-01

    The requirements of the electric utility industry as the primary potential market for geothermal energy are analyzed, based on a series of structured interviews with utility companies and financial institution executives. The interviews were designed to determine what information and technologies would be required before utilities would make investment decisions in favor of geothermal energy, the time frame in which the information and technologies would have to be available, and the influence of the governmental politics. The paper describes the geothermal resources, electric utility industry, its structure, the forces influencing utility companies, and their relationship to geothermal energy. A strategy for federal stimulation of utility investment in geothermal energy is suggested. Possibilities are discussed for stimulating utility investment through financial incentives, amelioration of institutional barriers, and technological improvements.

  5. Radiation curable coatings having nonadherent surfaces

    International Nuclear Information System (INIS)

    Gaske, J.E.; Georgas, N.T.

    1977-01-01

    Radiation polymerizable coatings having nonadherent surfaces are provided utilizing nonaqueous emulsions of a liquid alkyl hydrogen polysiloxane in a radiation polymerizable polyethylenic liquid. Polyacrylates in combination with amines, and ultraviolet photosensitizers are particularly contemplated for rapid nonair inhibited ultraviolet cure. 13 claims

  6. Modeling and analysis for surface roughness and material removal ...

    African Journals Online (AJOL)

    International Journal of Engineering, Science and Technology ... A multiple objective utility model has been studied to optimize both the dependent parameters. ... Keywords: UD-GFRP composites, ANOVA, multi response optimization, utility concept, regression modeling, surface roughness, material removal rate, ...

  7. Optimizing carbon dioxide utilization for microalgae biofilm cultivation.

    Science.gov (United States)

    Blanken, Ward; Schaap, Stefan; Theobald, Sophie; Rinzema, Arjen; Wijffels, René H; Janssen, Marcel

    2017-04-01

    The loss of carbon dioxide (CO 2 ) to the environment during microalgae cultivation is undesirable for both environmental and economic reasons. In this study, a phototrophic biofilm growth model was developed and validated with the objective to maximize both CO 2 utilization efficiency and production of microalgae in biofilms. The model was validated in growth experiments with CO 2 as the limiting substrate. The CO 2 utilization and biomass productivity were maximized by changing the gas flow rate, the number of biofilm reactors in series and gas composition. Based on simulations, the maximum CO 2 utilization efficiency that was reached was 96% based on a process employing flue gas. The corresponding drop in productivity was only 2% in comparison to the non-CO 2 limited reference situation. In order to achieve this, 25 biofilm reactors units, or more, must be operated in series. Based on these results, it was concluded that concentrated CO 2 streams and plug flow behavior of the gaseous phase over the biofilm surface are essential for high productivity and CO 2 utilization efficiency. Biotechnol. Bioeng. 2017;114: 769-776. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  8. Fly ash quality and utilization

    Energy Technology Data Exchange (ETDEWEB)

    Barta, L.E.; Lachner, L.; Wenzel, G.B. [Inst. for Energy, Budapest (Hungary); Beer, M.J. [Massachusetts Inst. of Technology, Cambridge, MA (United States)

    1995-12-01

    The quality of fly ash is of considerable importance to fly ash utilizers. The fly ash puzzolanic activity is one of the most important properties that determines the role of fly ash as a binding agent in the cementing process. The puzzolanic activity, however is a function of fly ash particle size and chemical composition. These parameters are closely related to the process of fly ash formation in pulverized coal fired furnaces. In turn, it is essential to understand the transformation of mineral matter during coal combustion. Due to the particle-to-particle variation of coal properties and the random coalescence of mineral particles, the properties of fly ash particles e.g. size, SiO{sub 2} content, viscosity can change considerably from particle to particle. These variations can be described by the use of the probability theory. Since the mean values of these randomly changing parameters are not sufficient to describe the behavior of individual fly ash particles during the formation of concrete, therefore it is necessary to investigate the distribution of these variables. Examples of these variations were examined by the Computer Controlled Scanning Electron Microscopy (CCSEM) for particle size and chemical composition for Texas lignite and Eagel Butte mineral matter and fly ash. The effect of combustion on the variations of these properties for both the fly ash and mineral matter were studied by using a laminar flow reactor. It is shown in our paper, that there are significant variations (about 40-50% around the mean values) of the above-listed properties for both coal samples. By comparing the particle size and chemical composition distributions of the mineral matter and fly ash, it was possible to conclude that for the Texas lignite mineral matter, the combustion did not effect significantly the distribution of these properties, however, for the Eagel Butte coal the combustion had a major impact on these mineral matter parameters.

  9. Enhancement of surface properties for coal beneficiation

    Energy Technology Data Exchange (ETDEWEB)

    Chander, S.; Aplan, F.F.

    1992-01-30

    This report will focus on means of pyrite removal from coal using surface-based coal cleaning technologies. The major subjects being addressed in this study are the natural and modulated surface properties of coal and pyrite and how they may best be utilized to facilitate their separation using advanced surface-based coal cleaning technology. Emphasis is based on modified flotation and oil agglomerative processes and the basic principles involved. The four areas being addressed are: (1) Collectorless flotation of pyrite; (2) Modulation of pyrite and coal hydrophobicity; (3) Emulsion processes and principles; (4) Evaluation of coal hydrophobicity.

  10. Surface modification of tribological components in transportation

    Energy Technology Data Exchange (ETDEWEB)

    Fenske, G.R.

    1992-11-01

    This paper reviews a number of programs funded through the Engineered Tribological Interfaces (ETI) Task area of the Tribology Program that utilize energetic beams of atoms to enhance the mechanical and microstructural properties of near-surface regions to improve the tribological performance of critical components. The processes used in these programs include techniques based on chemical vapor deposition, physical vapor deposition, and ion implantation. A common feature of these techniques is their ability to produce dense and adherent modified surfaces without need for subsequent grinding/polishing treatments. Another feature of these techniques is their ability to introduce a wide range of elements into near-surface regions.

  11. Surface hydrologic characteristics of proposed repository locations in the Palo Duro Basin of the Texas Panhandle

    International Nuclear Information System (INIS)

    1985-04-01

    This report provides a description of the surface hydrology in the two proposed locations of a high-level waste repository within the Palo Duro Basin of the Texas Panhandle. Included for consideration are the topography; the major drainage systems - Palo Duro, Tierra Blanca, and Tule Creeks, and Prairie Dog Town Fork of the Red River; and the most prominent impoundments, the playa lakes. The magnitude and frequency of precipitation throughout the region are discussed, and rainfall depth-duration-area data for the 100-year, 500-year, and probable maximum storms are presented. Soil properties are also described, with specific reference to the infiltration and runoff processes and the contribution of these processes to Ogallala aquifer recharge. A summary discussion of the local streams includes information on historical streamflow, a brief description of flooding, and results of a study of floodplains for the 100-year, 500-year, and probable maximum storms. The report concludes with a characterization of the water quality of these streams and an explanation of the local geologic influences on stream-water chemistry. 25 figures, 20 tables

  12. The performance of water utilities in Jordan.

    Science.gov (United States)

    Al-Assa'd, Tamer; Sauer, Johannes

    2010-01-01

    This paper aims to measure the relative performance of Jordan's water utilities for water sector (WS) and wastewater sector (WWS), and to investigate the major factors behind their inefficiencies. DEA (non-parametric method) and Tobit model (parametric method) were used at two stages. At the first stage DEA was used to evaluate the utilities' efficiency and to investigate the utilities' scale effect on efficiency. At the second stage Tobit model (regression) is applied to determine the impact of the non-controllable factors on utilities' inefficiencies where the efficiency score is the dependent variable in the regression. The results of DEA showed that there is a potential to reduce inputs level: water supply and operational expense (OPEX) for WS, and treated wastewater and OPEX for WWS, by around 15-20 and 23-27%, respectively. Aqaba and Jarash utilities are the most efficient utilities in the WS, while it is Amman utility in the WWS. The utility size has relatively moderate effect on the relative performance. It is concluded that the medium utility size for WS and large utility size for WWS is the most appropriate. Tobit model results indicate that commercialization activities have a clear positive impact on efficiency improvement for both sectors.

  13. Invariance and inconsistency in utility ratings.

    Science.gov (United States)

    Bravata, Dena M; Nelson, Lorene M; Garber, Alan M; Goldstein, Mary K

    2005-01-01

    To assess utilities of composite health states for dependence in activities of daily living (ADLs) for invariance (i.e., when subjects provide a utility of 1 for all health states) and order inconsistency (i.e., when subjects order their utilities such that their utility for a combination of ADL dependencies is greater than their utility for any subset of the combination). Each of the 400 subjects, age 65 y and older, enrolled in one of several regional medical centers of the Kaiser Permanente Medical Care Program of Northern California and provided standard-gamble utilities for single ADL dependencies (e.g., bathing, dressing, continence) and for dependence in 8 other combinations of ADL dependencies. For order-inconsistent responses, the authors calculated the maximum magnitude of inconsistency as the maximum difference between the utility for the combined ADL dependence health state and that of its inconsistent subset. A total of 76 subjects (19%) gave a utility of 1.0 for all health states presented to them; 19 (5%) gave the same utility other than 1.0 for all health states; 130 (33%) gave at least 1 utility Invariance was associated with a Mini-Mental Status Examination score invariant (0.88 [0.24]) was higher than among inconsistent subjects (0.80 [0.27]; P = 0.01). Invariance and order inconsistencies in utility ratings for complex health states occur frequently. Utilities of consistent subjects may differ from those of inconsistent subjects. Utility assessments should attempt to measure and report these patterns.

  14. Zwitterionic materials for antifouling membrane surface construction.

    Science.gov (United States)

    He, Mingrui; Gao, Kang; Zhou, Linjie; Jiao, Zhiwei; Wu, Mengyuan; Cao, Jialin; You, Xinda; Cai, Ziyi; Su, Yanlei; Jiang, Zhongyi

    2016-08-01

    Membrane separation processes are often perplexed by severe and ubiquitous membrane fouling. Zwitterionic materials, keeping electric neutrality with equivalent positive and negative charged groups, are well known for their superior antifouling properties and have been broadly utilized to construct antifouling surfaces for medical devices, biosensors and marine coatings applications. In recent years, zwitterionic materials have been more and more frequently utilized for constructing antifouling membrane surfaces. In this review, the antifouling mechanisms of zwitterionic materials as well as their biomimetic prototypes in cell membranes will be discussed, followed by the survey of common approaches to incorporate zwitterionic materials onto membrane surfaces including surface grafting, surface segregation, biomimetic adhesion, surface coating and so on. The potential applications of these antifouling membranes are also embedded. Finally, we will present a brief perspective on the future development of zwitterionic materials modified antifouling membranes. Membrane fouling is a severe problem hampering the application of membrane separation technology. The properties of membrane surfaces play a critical role in membrane fouling and antifouling behavior/performance. Antifouling membrane surface construction has evolved as a hot research issue for the development of membrane processes. Zwitterionic modification of membrane surfaces has been recognized as an effective strategy to resist membrane fouling. This review summarizes the antifouling mechanisms of zwitterionic materials inspired by cell membranes as well as the popular approaches to incorporate them onto membrane surfaces. It can help form a comprehensive knowledge about the principles and methods of modifying membrane surfaces with zwitterionic materials. Finally, we propose the possible future research directions of zwitterionic materials modified antifouling membranes. Copyright © 2016 Acta Materialia Inc

  15. On-line monitoring system for utility boiler diagnostics

    International Nuclear Information System (INIS)

    Radovanovic, P.M.; Afgan, N.H.; Caralho, M.G.

    1997-01-01

    The paper deals with the new developed modular type Monitoring System for Utility Boiler Diagnostics. Each module is intended to assess the specific process and can be used as a stand alone application. Four modules are developed, namely: LTC - module for the on-line monitoring of parameters related to the life-time consumption of selected boiler components; TRD - module for the tube rupture detection by the position and working fluid Ieakage quantity; FAM - module for the boiler surfaces fouling (slagging) assessment and FLAP - module for visualization of the boiler furnace flame position. All four modules are tested on respective pilot plants built oil the 200 and 300 MWe utility boilers. Monitoring System is commercially available and can be realized in any combination of its modules depending on demands induced by the operational problems of specific boiler. Further development of Monitoring System is performed in accordance with the respective EU project on development of Boiler Expert System. (Author)

  16. Materials selection guidelines for geothermal energy utilization systems

    Energy Technology Data Exchange (ETDEWEB)

    Ellis, P.F. II; Conover, M.F.

    1981-01-01

    This manual includes geothermal fluid chemistry, corrosion test data, and materials operating experience. Systems using geothermal energy in El Salvador, Iceland, Italy, Japan, Mexico, New Zealand, and the United States are described. The manual provides materials selection guidelines for surface equipment of future geothermal energy systems. The key chemical species that are significant in determining corrosiveness of geothermal fluids are identified. The utilization modes of geothermal energy are defined as well as the various physical fluid parameters that affect corrosiveness. Both detailed and summarized results of materials performance tests and applicable operating experiences from forty sites throughout the world are presented. The application of various non-metal materials in geothermal environments are discussed. Included in appendices are: corrosion behavior of specific alloy classes in geothermal fluids, corrosion in seawater desalination plants, worldwide geothermal power production, DOE-sponsored utilization projects, plant availability, relative costs of alloys, and composition of alloys. (MHR)

  17. BARRIER ISSUES TO THE UTILIZATION OF BIOMASS

    Energy Technology Data Exchange (ETDEWEB)

    Bruce C. Folkedahl; Darren D. Schmidt; Greg F. Weber; Christopher J. Zygarlicke

    2001-10-01

    The Energy & Environmental Research Center (EERC) is conducting a project to examine the fundamental issues limiting the use of biomass in small industrial steam/power systems in order to increase the future use of this valuable domestic resource. Specifically, the EERC is attempting to elucidate the ash-related problems--grate clinkering and heat exchange surface fouling--associated with cofiring coal and biomass in grate-fired systems. Utilization of biomass in stoker boilers designed for coal can be a cause of concern for boiler operators. Boilers that were designed for low volatile fuels with lower reactivities can experience damaging fouling when switched to higher volatile and more reactive lower-rank fuels, such as when cofiring biomass. Higher heat release rates at the grate can cause more clinkering or slagging at the grate because of higher temperatures. Combustion and loss of volatile matter can start too early for biomass fuels compared to the design fuel, vaporizing alkali and chlorides which then condense on rear walls and heat exchange tube banks in the convective pass of the stoker, causing noticeable increases in fouling. In addition, stoker-fired boilers that switch to biomass blends may encounter new chemical species such as potassium sulfates and various chlorides, in combination with different flue gas temperatures because of changes in fuel heating value which can adversely affect ash deposition behavior. The goal of this project is to identify the primary ash mechanisms related to grate clinkering and heat exchange surface fouling associated with cofiring coal and biomass--specifically wood and agricultural residuals--in grate-fired systems, leading to future mitigation of these problems. The specific technical objectives of the project are: Modification of an existing EERC pilot-scale combustion system to simulate a grate-fired system; Verification testing of the simulator; Laboratory-scale testing and fuel characterization to determine ash

  18. BARRIER ISSUES TO THE UTILIZATION OF BIOMASS

    Energy Technology Data Exchange (ETDEWEB)

    Bruce C. Folkedahl; Jay R. Gunderson; Darren D. Schmidt; Greg F. Weber; Christopher J. Zygarlicke

    2002-09-01

    The Energy & Environmental Research Center (EERC) has completed a project to examine fundamental issues that could limit the use of biomass in small industrial steam/power systems in order to increase the future use of this valuable domestic resource. Specifically, the EERC attempted to elucidate the ash-related problems--grate clinkering and heat exchange surface fouling--associated with cofiring coal and biomass in grate-fired systems. Utilization of biomass in stoker boilers designed for coal can be a cause of concern for boiler operators. Boilers that were designed for low-volatile fuels with lower reactivities can experience problematic fouling when switched to higher-volatile and more reactive coal-biomass blends. Higher heat release rates at the grate can cause increased clinkering or slagging at the grate due to higher temperatures. Combustion and loss of volatile matter can start much earlier for biomass fuels compared to design fuel, vaporizing alkali and chlorides which then condense on rear walls and heat exchange tube banks in the convective pass of the stoker, causing noticeable increases in fouling. In addition, stoker-fired boilers that switch to biomass blends may encounter new chemical species such as potassium sulfates, various chlorides, and phosphates. These species in combination with different flue gas temperatures, because of changes in fuel heating value, can adversely affect ash deposition behavior. The goal of this project was to identify the primary ash mechanisms related to grate clinkering and heat exchange surface fouling associated with cofiring coal and biomass--specifically wood and agricultural residuals--in grate-fired systems, leading to future mitigation of these problems. The specific technical objectives of the project were: (1) Modification of an existing pilot-scale combustion system to simulate a grate-fired system. (2) Verification testing of the simulator. (3) Laboratory-scale testing and fuel characterization to

  19. Advanced Gasification By-Product Utilization

    Energy Technology Data Exchange (ETDEWEB)

    Rodney Andrews; Aurora Rubel; Jack Groppo; Brock Marrs; Ari Geertsema; Frank Huggins; M. Mercedes Maroto-Valer; Brandie M. Markley; Zhe Lu; Harold Schobert

    2006-08-31

    objectives of this collaborative effort between the University of Kentucky Center for Applied Energy Research (CAER), The Pennsylvania State University Energy Institute, and industry collaborators supplying gasifier char samples were to investigate the potential use of gasifier slag carbons as a source of low cost sorbent for Hg and NOX capture from combustion flue gas, concrete applications, polymer fillers and as a source of activated carbons. Primary objectives were to determine the relationship of surface area, pore size, pore size distribution, and mineral content on Hg storage of gasifier carbons and to define the site of Hg capture. The ability of gasifier slag carbon to capture NOX and the effect of NOX on Hg adsorption were goals. Secondary goals were the determination of the potential for use of the slags for cement and filler applications. Since gasifier chars have already gone through a devolatilization process in a reducing atmosphere in the gasifier, they only required to be activated to be used as activated carbons. Therefore, the principal objective of the work at PSU was to characterize and utilize gasification slag carbons for the production of activated carbons and other carbon fillers. Tests for the Hg and NOX adsorption potential of these activated gasifier carbons were performed at the CAER. During the course of this project, gasifier slag samples chemically and physically characterized at UK were supplied to PSU who also characterized the samples for sorption characteristics and independently tested for Hg-capture. At the CAER as-received slags were tested for Hg and NOX adsorption. The most promising of these were activated chemically. The PSU group applied thermal and steam activation to a representative group of the gasifier slag samples separated by particle sizes. The activated samples were tested at UK for Hg-sorption and NOX capture and the most promising Hg adsorbers were tested for Hg capture in a simulated flue gas. Both UK and PSU tested the

  20. Modelling of biomass utilization for energy purpose

    Energy Technology Data Exchange (ETDEWEB)

    Grzybek, Anna (ed.)

    2010-07-01

    From the introduction: The following natural conditions enable agriculture development: surface configuration, climatic conditions including insolation, temperature, rainfalls, winds and frost periods, soil conditions (fertility), water conditions. Water conditions are determined by sum of rainfalls, evaporation quantity and water transpiration by plants. Climatic conditions and soil conditions are decisive factors for agricultural land use. They determine plants selection for crop and expected yield level. Non-natural conditions are also important for agriculture development. The following factors belong to them: labour force, structure of the land ownership, farms size, fertilization, herbicides utilisation, farm mechanisation, education and skills of a farmer, EU and state agricultural policy. EU and Polish agricultural policy is characterized by protectionalism. It means a financial support system and preferential credits with implementation of other means for agricultural market protection. Poland lies in the sphere of clashes between influences of continental climate (with quite dry summers and cold winters) and moderate Atlantic climate. These clashes are reason of unstable conditions for agricultural production. The annual average air temperature varies from 6.0 to 8.8 degrees Celsius. The length of the thermal vegetation period is about 220 days and only in South-West part of Poland exceeds 230 days. The annual sum of rainfall is about 500-600 mm on lowlands, 600-700 mm on highlands and it is above 1000 mm in mountains. Central Poland (Masovia, Great Poland, Kuyavia) belongs to European regions with the smallest rainfall sum which not exceeds 550 mm. Atlantic Ocean significantly influences on Polish climate from west side of Poland and Asia continent from east side of Poland. Rainfall is another significant factor. Western Europe has significantly higher rainfall in comparison with Poland. Polish agriculture is featured by: high amount of smallest farms in

  1. Cold atoms close to surfaces

    DEFF Research Database (Denmark)

    Krüger, Peter; Wildermuth, Stephan; Hofferberth, Sebastian

    2005-01-01

    Microscopic atom optical devices integrated on atom chips allow to precisely control and manipulate ultra-cold (T atoms and Bose-Einstein condensates (BECs) close to surfaces. The relevant energy scale of a BEC is extremely small (down to ... be utilized as a sensor for variations of the potential energy of the atoms close to the surface. Here we describe how to use trapped atoms as a measurement device and analyze the performance and flexibility of the field sensor. We demonstrate microscopic magnetic imaging with simultaneous high spatial...... variations of the current flow direction, resulting from local properties of the wire. These disorder potentials found near lithographically fabricated wires are two orders of magnitude smaller than those measured close to electroplated conductors....

  2. On surface approximation using developable surfaces

    DEFF Research Database (Denmark)

    Chen, H. Y.; Lee, I. K.; Leopoldseder, s.

    1999-01-01

    We introduce a method for approximating a given surface by a developable surface. It will be either a G(1) surface consisting of pieces of cones or cylinders of revolution or a G(r) NURBS developable surface. Our algorithm will also deal properly with the problems of reverse engineering and produ...... robust approximation of given scattered data. The presented technique can be applied in computer aided manufacturing, e.g. in shipbuilding. (C) 1999 Academic Press....

  3. On surface approximation using developable surfaces

    DEFF Research Database (Denmark)

    Chen, H. Y.; Lee, I. K.; Leopoldseder, S.

    1998-01-01

    We introduce a method for approximating a given surface by a developable surface. It will be either a G_1 surface consisting of pieces of cones or cylinders of revolution or a G_r NURBS developable surface. Our algorithm will also deal properly with the problems of reverse engineering and produce...... robust approximation of given scattered data. The presented technique can be applied in computer aided manufacturing, e.g. in shipbuilding....

  4. An integral field spectrograph utilizing mirrorlet arrays

    Science.gov (United States)

    Chamberlin, Phillip C.; Gong, Qian

    2016-09-01

    An integral field spectrograph (IFS) has been developed that utilizes a new and novel optical design to observe two spatial dimensions simultaneously with one spectral dimension. This design employs an optical 2-D array of reflecting and focusing mirrorlets. This mirrorlet array is placed at the imaging plane of the front-end telescope to generate a 2-D array of tiny spots replacing what would be the slit in a traditional slit spectrometer design. After the mirrorlet in the optical path, a grating on a concave mirror surface will image the spot array and provide high-resolution spectrum for each spatial element at the same time; therefore, the IFS simultaneously obtains the 3-D data cube of two spatial and one spectral dimensions. The new mirrorlet technology is currently in-house and undergoing laboratory testing at NASA Goddard Space Flight Center. Section 1 describes traditional classes of instruments that are used in Heliophysics missions and a quick introduction to the new IFS design. Section 2 discusses the details of the most generic mirrorlet IFS, while section 3 presents test results of a lab-based instrument. An example application to a Heliophysics mission to study solar eruptive events in extreme ultraviolet wavelengths is presented in section 4 that has high spatial resolution (0.5 arc sec pixels) in the two spatial dimensions and high spectral resolution (66 mÅ) across a 15 Å spectral window. Section 4 also concludes with some other optical variations that could be employed on the more basic IFS for further capabilities of this type of instrument.

  5. An Integral Field Spectrograph Utilizing Mirrorlet Arrays

    Science.gov (United States)

    Chamberlin, Phillip C.; Gong, Qian

    2016-01-01

    An integral field spectrograph (IFS) has been developed that utilizes a new and novel optical design to observe two spatial dimensions simultaneously with one spectral dimension. This design employs an optical 2-D array of reflecting and focusing mirrorlets. This mirrorlet array is placed at the imaging plane of the front-end telescope to generate a 2-D array of tiny spots replacing what would be the slit in a traditional slit spectrometer design. After the mirrorlet in the optical path, a grating on a concave mirror surface will image the spot array and provide high-resolution spectrum for each spatial element at the same time; therefore, the IFS simultaneously obtains the 3-D data cube of two spatial and one spectral dimensions. The new mirrorlet technology is currently in-house and undergoing laboratory testing at NASA Goddard Space Flight Center. Section 1 describes traditional classes of instruments that are used in Heliophysics missions and a quick introduction to the new IFS design. Section 2 discusses the details of the most generic mirrorlet IFS, while section 3 presents test results of a lab-based instrument. An example application to a Heliophysics mission to study solar eruptive events in extreme ultraviolet wavelengths is presented in section 4 that has high spatial resolution (0.5 arc sec pixels) in the two spatial dimensions and high spectral resolution (66 m) across a 15 spectral window. Section 4 also concludes with some other optical variations that could be employed on the more basic IFS for further capabilities of this type of instrument.

  6. Radiological considerations of phosphogypsum utilization in agriculture

    International Nuclear Information System (INIS)

    Lindeken, C.L.

    1980-01-01

    The radiological concerns associated with phosphogypsum utilization in agriculture have been placed in perspective by considering the consequences of a hypothetical case involving heavy long term applications of phosphogypsum. In California, such a schedule might consist of an initial gypsum application of 10 tons/acre followed by alternate year applications of 5 tons/acre. If the radium content of the gypsum were 15 pCi/g and the till depth 6 inches, this schedule could be maintained for more than 100 years before the radium buildup in the soil would reach a proposed federal concentration limit of 5 pCi/g. An agricultural worker spending 40 h a week in a field containing 5 pCi/g of radium would be exposed to terrestrial radiation of about 7 μR/h above background. This exposure would result in an annual radiation dose of about 15 mrem, which is 3% of the recommended limit for an individual working in an uncontrolled area. Five pCi/g of radium in the soil could generate airborne radon daughter concentrations exceeding the concentration limit proposed for residential exposure. However, as residential exposure limits are predicated on 75% of continuous occupancy, these limits should not be applied to agricultural workers because of the seasonal nature of their work. Radium uptake by food crops grown in the hypothetical soil would result in a 50 year integrated dose to the bone surface of 1.4 rem. This dose is conservatively based on the assumption that an adult's total vegetable diet comes from this source and that consumption was continuous during the 50 year period

  7. Virtual Observatories: Requirements for Utility

    Science.gov (United States)

    Paxton, L. J.

    2008-12-01

    The principal act that separates science from engineering is that of discovery. Virtual Observatories are a development with great potential for advancing our ability to do science by enabling us to do research effectively and to do research across disciplines. Access to data is one of the factors that enables discovery. A well-designed VO should enable discovery as well as providing for a uniform means by which data are accessed: thus, enabling discovery is the key challenge of a VO in fact it is and should be the principle that distinguishes a VO from a traditional archive. As the number of satellites in the Heliophysics Great observatory starts to decline due to the slower launch cadence and the reduction in funding for extended missions, it becomes more imperative that the community have the means to fully utilize and access the available resources. With the proliferation of low-cost computing and community-based models, cross-disciplinary studies become the new frontier. Many, if not the great majority of research papers are, at this time, confined to a particular discipline. Some of this "stove piping" may be due to the difficulty in accessing products from outside one's own discipline. One would hope and expect that VOs would address this. Two of the principal challenges associated with the vitality of the VOs, aside from the provision of the funds required to maintain the VOs, is 1) the limitation on the availability of data from non-NASA sources and 2) the need for some level of continued support for expertise on the data accessed through the VOs. The first issue is one of culture - some organizations support the view that the data belong to the PI whereas in Heliophysics "data rights" are curtailed. The second issue is to be addressed by the concept of the Resident Archive. This talk will provide an overview of the issues and challenges associated with VOs, Resident Archives, data rights, space missions, and instruments and their associated ground data

  8. Stochastic Dominance under the Nonlinear Expected Utilities

    Directory of Open Access Journals (Sweden)

    Xinling Xiao

    2014-01-01

    Full Text Available In 1947, von Neumann and Morgenstern introduced the well-known expected utility and the related axiomatic system (see von Neumann and Morgenstern (1953. It is widely used in economics, for example, financial economics. But the well-known Allais paradox (see Allais (1979 shows that the linear expected utility has some limitations sometimes. Because of this, Peng proposed a concept of nonlinear expected utility (see Peng (2005. In this paper we propose a concept of stochastic dominance under the nonlinear expected utilities. We give sufficient conditions on which a random choice X stochastically dominates a random choice Y under the nonlinear expected utilities. We also provide sufficient conditions on which a random choice X strictly stochastically dominates a random choice Y under the sublinear expected utilities.

  9. Utilities' ''obligation to serve'' under deregulation

    International Nuclear Information System (INIS)

    Alexander, C.B.

    1997-01-01

    The utility no longer has protected status, and the traditional franchise concept is under attack. Exclusive rights once conveyed to the utilities are being denied and not just in the area of gas sales. Exclusive rights once conveyed to utilities will be denied in more areas. State by state, the utilities' franchise is being examined to see which, if any, of its provisions are necessary in a deregulated environment. Can the free market provide everything that's been provided for many years under monopolistic arrangements? Some of the most critical and difficult of these provisions concern the obligation to serve, which utilities, in most states, have assumed as part of their franchise agreement. Regulators, courts, utilities, marketers and others are busy sorting through these issues, but resolution could take years. The paper discusses deregulation, universal service fee, representation without taxation, suppliers and marketer restrictions

  10. Trends in Utility Green Pricing Programs (2006)

    Energy Technology Data Exchange (ETDEWEB)

    Bird, L.; Kaiser, M.

    2007-10-01

    In the early 1990s, only a handful of utilities offered their customers a choice of purchasing electricity generated from renewable energy sources. Today, more than 750 utilities--or about 25% of all utilities nationally--provide their customers a "green power" option. Through these programs, more than 70 million customers have the ability to purchase renewable energy to meet some portion or all of their electricity needs--or make contributions to support the development of renewable energy resources. Typically, customers pay a premium above standard electricity rates for this service. This report presents year-end 2006 data on utility green pricing programs, and examines trends in consumer response and program implementation over time. The data in this report, which were obtained via a questionnaire distributed to utility green pricing program managers, can be used by utilities to benchmark the success of their green power programs.

  11. The laboratory test utilization management toolbox.

    Science.gov (United States)

    Baird, Geoffrey

    2014-01-01

    Efficiently managing laboratory test utilization requires both ensuring adequate utilization of needed tests in some patients and discouraging superfluous tests in other patients. After the difficult clinical decision is made to define the patients that do and do not need a test, a wealth of interventions are available to the clinician and laboratorian to help guide appropriate utilization. These interventions are collectively referred to here as the utilization management toolbox. Experience has shown that some tools in the toolbox are weak and other are strong, and that tools are most effective when many are used simultaneously. While the outcomes of utilization management studies are not always as concrete as may be desired, what data is available in the literature indicate that strong utilization management interventions are safe and effective measures to improve patient health and reduce waste in an era of increasing financial pressure.

  12. Lessons Learned: Community Solar for Municipal Utilities

    Energy Technology Data Exchange (ETDEWEB)

    2016-12-01

    This report outlines the work that STAT has completed, discusses the range of approaches utilities are taking, and highlights several challenges municipal utilities face in deciding whether and how to pursue community solar. As this report shows, there is no 'silver bullet' in terms of municipal utility community solar design or implementation - programs vary significantly and are highly dependent on localized contexts.

  13. Capacity and Capacity Utilization in Fishing Industries

    OpenAIRE

    Kirkley, James E; Squires, Dale

    1999-01-01

    Excess capacity of fishing fleets is one of the most pressing problems facing the world's fisheries and the sustainable harvesting of resource stocks. Considerable confusion persists over the definition and measurement of capacity and capacity utilization in fishing. Fishing capacity and capacity utilization, rather than capital (or effort) utilization, provide the appropriate framework. This paper provides both technological-economic and economic definitions of capacity and excess capacity i...

  14. Present and possible utilization of PUSPATI reactor

    International Nuclear Information System (INIS)

    Gui Ah Auu.

    1983-01-01

    The utilization of PUSPATI TRIGA Mark II Reactor (PTR) has increased reasonably well since its commissioning last year. PTR was used mainly for training of operators, neutron flux measurements and neutron activation analysis. However, the present utilization data indicates that further increase in PTR utilization to include teaching and the usage of the beam ports is desirable. Some possible areas of PTR applications in the future in relevance to our needs are also described in this paper. (author)

  15. Parametrization of translational surfaces

    OpenAIRE

    Perez-Diaz, Sonia; Shen, Liyong

    2014-01-01

    The algebraic translational surface is a typical modeling surface in computer aided design and architecture industry. In this paper, we give a necessary and sufficient condition for that algebraic surface having a standard parametric representation and our proof is constructive. If the given algebraic surface is translational, then we can compute a standard parametric representation for the surface.

  16. Water and Sewage Utilities Sector (NAICS 2213)

    Science.gov (United States)

    Environmental regulation information for water utilities, including drinking and wastewater treatment facilities. Includes links to NESHAP for POTW, compliance information, and information about pretreatment programs.

  17. Utility FGD Survey, January--December 1989

    Energy Technology Data Exchange (ETDEWEB)

    Hance, S.L.; McKibben, R.S.; Jones, F.M. (IT Corp., Cincinnati, OH (United States))

    1992-03-01

    The Utility flue gas desulfurization (FGD) Survey report, which is generated by a computerized data base management system, represents a survey of operational and planned domestic utility flue gas desulfurization (FGD) systems. It summarizes information contributed by the utility industry, system and equipment suppliers, system designers, research organizations, and regulatory agencies. The data cover system design, fuel characteristics, operating history, and actual system performance. Also included is a unit-by-unit discussion of problems and solutions associated with the boilers, scrubbers, and FGD systems. The development status (operational, under construction, or in the planning stages), system supplier, process, waste disposal practice, and regulatory class are tabulated alphabetically by utility company.

  18. Mining High Utility Itemsets with Regular Occurrence

    Directory of Open Access Journals (Sweden)

    Komate Amphawan

    2016-09-01

    Full Text Available High utility itemset mining (HUIM plays an important role in the data mining community and in a wide range of applications. For example, in retail business it is used for finding sets of sold products that give high profit, low cost, etc. These itemsets can help improve marketing strategies, make promotions/ advertisements, etc. However, since HUIM only considers utility values of items/itemsets, it may not be sufficient to observe product-buying behavior of customers such as information related to “regular purchases of sets of products having a high profit margin”. To address this issue, the occurrence behavior of itemsets (in the term of regularity simultaneously with their utility values was investigated. Then, the problem of mining high utility itemsets with regular occurrence (MHUIR to find sets of co-occurrence items with high utility values and regular occurrence in a database was considered. An efficient single-pass algorithm, called MHUIRA, was introduced. A new modified utility-list structure, called NUL, was designed to efficiently maintain utility values and occurrence information and to increase the efficiency of computing the utility of itemsets. Experimental studies on real and synthetic datasets and complexity analyses are provided to show the efficiency of MHUIRA combined with NUL in terms of time and space usage for mining interesting itemsets based on regularity and utility constraints.

  19. Utilities for high performance dispersion model PHYSIC

    International Nuclear Information System (INIS)

    Yamazawa, Hiromi

    1992-09-01

    The description and usage of the utilities for the dispersion calculation model PHYSIC were summarized. The model was developed in the study of developing high performance SPEEDI with the purpose of introducing meteorological forecast function into the environmental emergency response system. The procedure of PHYSIC calculation consists of three steps; preparation of relevant files, creation and submission of JCL, and graphic output of results. A user can carry out the above procedure with the help of the Geographical Data Processing Utility, the Model Control Utility, and the Graphic Output Utility. (author)

  20. Lunar resources: possibilities for utilization

    Science.gov (United States)

    Shevchenko, Vladislav

    South polar regions that satisfy the stated goals. Lunar titanium: Objectives of the Lunar Reconnaissance Orbital (LRO) mission are to find potential safe landing sites and locate potential resources. New imaging from NASA' LRO has shown the Moon has areas that are rich in titanium ore. Some lunar rocks have ten times as much titanium ore as rocks on Earth. The titanium deposits were observed with the help of visible and ultraviolet imaging. The researchers scanned the lunar surface, collecting roughly 4,000 images, and compared the brightness in the range of wavelengths from ultraviolet to visible light. The scientists then cross-referenced their findings with lunar samples that were brought back to Earth from NASA's Apollo flights and the Russian Luna missions. The abundance of titanium has puzzled researchers. While rocks on Earth contain around one percent titanium at most, the lunar rocks ranged from one percent all the way up to ten percent. Researchers still don't why the titanium levels are higher on the moon, but do believe it gives insight into the conditions of the Moon shortly after it formed. The titanium seems to be found primarily in the mineral ilmenite, a compound containing iron, titanium, and oxygen. Lunar rare earth elements: The Procellarum KREEP Terrane (PKT) dominates the nearside of the Moon. "KREEP" is an acronym for lunar rocks that are high in potassium (K), rare earth elements (REE), and phosphorous (P). The PKT is a mixture of assorted rocks, including most of the mare basalts on the Moon, and is characterized by high Th (about 5 parts per million on average). This region has also been called the "high-Th Oval Region". PKT occupies about 16% of the lunar surface.