Coal combustion waste management at landfills and surface impoundments 1994-2004.

Energy Technology Data Exchange (ETDEWEB)

Elcock, D.; Ranek, N. L.; Environmental Science Division

2006-09-08

On May 22, 2000, as required by Congress in its 1980 Amendments to the Resource Conservation and Recovery Act (RCRA), the U.S. Environmental Protection Agency (EPA) issued a Regulatory Determination on Wastes from the Combustion of Fossil Fuels. On the basis of information contained in its 1999 Report to Congress: Wastes from the Combustion of Fossil Fuels, the EPA concluded that coal combustion wastes (CCWs), also known as coal combustion by-products (CCBs), did not warrant regulation under Subtitle C of RCRA, and it retained the existing hazardous waste exemption for these materials under RCRA Section 3001(b)(3)(C). However, the EPA also determined that national regulations under Subtitle D of RCRA were warranted for CCWs that are disposed of in landfills or surface impoundments. The EPA made this determination in part on the basis of its findings that 'present disposal practices are such that, in 1995, these wastes were being managed in 40 percent to 70 percent of landfills and surface impoundments without reasonable controls in place, particularly in the area of groundwater monitoring; and while there have been substantive improvements in state regulatory programs, we have also identified gaps in State oversight' (EPA 2000). The 1999 Report to Congress (RTC), however, may not have reflected the changes in CCW disposal practices that occurred since the cutoff date (1995) of its database and subsequent developments. The U.S. Department of Energy (DOE) and the EPA discussed this issue and decided to conduct a joint DOE/EPA study to collect new information on the recent CCW management practices by the power industry. It was agreed that such information would provide a perspective on the chronological adoption of control measures in CCW units based on State regulations. A team of experts from the EPA, industry, and DOE (with support from Argonne National Laboratory) was established to develop a mutually acceptable approach for collecting and analyzing data

Cumulative impoundment evaporation in water resource management within the mid-Atlantic: A case study in Virginia

Science.gov (United States)

Scott, D.; Burgholzer, R.; Kleiner, J.; Brogan, C. O.; Julson, C.; Withers, E.

2017-12-01

Across the eastern United States, successful management of water resources to satisfy the competing demands for human consumption, industry, agriculture, and ecosystems requires both water quality and water quantity considerations. Over the last 2 decades, low streamflows during dry summers have increased scrutiny on water supply withdrawals. Within Virginia, a statewide hydrologic model provides quantitative assessments on impacts from proposed water withdrawals to downstream river flow. Currently, evaporative losses are only accounted for from the large reservoirs. In this study, we sought to provide a baseline estimate for the cumulative evaporation from impoundments across all of the major river basins in Virginia. Virginia provides an ideal case study for the competing water demands in the mid-Atlantic region given the unique tracking of water withdrawals throughout the river corridor. In the over 73,000 Virginia impoundments, the cumulative annual impoundment evaporation was 706 MGD, or 49% of the permitted water withdrawal. The largest reservoirs (>100 acres) represented over 400 MGD, and 136 MGD for the smaller impoundments (water loss (evaporation + demand), with some areas where impoundment evaporation was greater than human water demand. Seasonally, our results suggest that cumulative impoundment evaporation in some watersheds greatly impacts streamflow during low flow periods. Our results demonstrate that future water supply planning will require not only understanding evaporation within large reservoirs, but also the thousands of small impoundments across the landscape.

Protection of uranium tailings impoundments against overland erosion

International Nuclear Information System (INIS)

Walters, W.H.; Skaggs, R.L.

1986-01-01

This study investigates the problems involved in designing protection methods to prevent erosion of a uranium tailings impoundment cover from rainfall and runoff (overland flow) processes. The study addresses the side slopes and top surface as separate elements. The side slopes are more subject to gully erosion and require absolute protection such as that provided by rock riprap. The flatter top surface needs much less protection (vegetation/rock combinations) but some estimate of erosion rates are needed to compare alternatives. A literature review indicated that, currently, procedures are not available for the design of rock riprap to prevent gully erosion. Therefore, rock protection on the side slope will have to be based upon engineering judgment determined by the particular site conditions. The Manning-kinetic equations (velocity and depth of runoff) were investigated as a possible aid to the design of gully erosion protection. Guidelines are suggested for the use of rock riprap to prevent gully erosion. Three mathematical models were used to compute erosion rates for the top surface of a hypothetical tailings impoundment. The results recommend that one or possibly both of the regression models could be used to evaluate preliminary protection designs for the top surface. A physical process simulation model should be used for the final design. 30 refs., 13 figs., 16 tabs

Effects of rock riprap design parameters on flood protection costs for uranium tailings impoundments

International Nuclear Information System (INIS)

Ecker, R.M.

1984-07-01

The Pacific Northwest Laboratory (PNL) is studying the problem of long-term protection of earthen covers on decommissioned uranium tailings impoundments. The major erosive forces acting on these covers will be river flooding and overland flow from rainfall-runoff. For impoundments adjacent to rivers, overbank flooding presents the greater potential for significant erosion. To protect the earthen covers against flood erosion, rock riprap armoring will be placed over the cover surface. Because of the large size rock usually required for riprap, the quarrying, transport, and placement of the rock could be a significant part of the decommissioning cost. This report examines the sensitivity of riprap protection costs to certain design parameters at tailings impoundments. The parameters include flood discharge, riprap materials, impoundment side slopes, and an added safety factor. Two decommissioned tailings impoundments are used as case studies for the evaluation. These are the Grand Junction, Colorado, impoundment located adjacent to the Colorado River and the Slickrock, Colorado, impoundment located adjacent to the Dolores River. The evaluation considers only the cost of riprap protection against flood erosion. The study results show that embankment side slope and rock specific gravity can have optimum values or ranges at a specific site. For both case study sites the optimum side slope is about 5H:1V. Of the rock sources considered at Grand Junction, the optimum specific gravity would be about 2.50; however, an optimum rock specific gravity for the Slickrock site could not be determined. Other results indicate that the arbitrary safety factor usually added in riprap design can lead to large increases in protection costs. 22 references, 19 figures, 15 tables

Distribution of aquifers, liquid-waste impoundments, and municipal water-supply sources, Massachusetts

Science.gov (United States)

Delaney, David F.; Maevsky, Anthony

1980-01-01

Impoundments of liquid waste are potential sources of ground-water contamination in Massachusetts. The map report, at a scale of 1 inch equals 4 miles, shows the idstribution of aquifers and the locations of municipal water-supply sources and known liquid-waste impoundments. Ground water, an important source of municipal water supply, is produced from shallow sand and gravel aquifers that are generally unconfined, less than 200 feet thick, and yield less than 2,000 gallons per minute to individual wells. These aquifers commonly occupy lowlands and stream valleys and are most extensive in eastern Massachusetts. Surface impoundments of liquid waste are commonly located over these aquifers. These impoundments may leak and allow waste to infiltrate underlying aquifers and alter their water quality. (USGS)

Application of carbon isotopes to detect seepage out of coalbed natural gas produced water impoundments

International Nuclear Information System (INIS)

Sharma, Shikha; Baggett, Joshua K.

2011-01-01

Highlights: → Coalbed natural gas extraction results in large amount of produced water. → Risk of deterioration of ambient water quality. → Carbon isotope natural tracer for detecting seepage from produced water impoundments. - Abstract: Coalbed natural gas (CBNG) production from coal bed aquifers requires large volumes of produced water to be pumped from the subsurface. The produced water ranges from high quality that meets state and federal drinking water standards to low quality due to increased salinity and/or sodicity. The Powder River Basin of northeastern Wyoming is a major coalbed natural gas producing region, where water quality generally decreases moving from the southeastern portion of the basin towards the center. Most produced water in Wyoming is disposed into impoundments and other surface drainages, where it may infiltrate into shallow groundwater. Groundwater degradation caused by infiltration of CBNG produced water holding impoundments into arid, soluble salt-rich soils is an issue of immense importance because groundwater is a major source for stock water, irrigation, and drinking water for many small communities in these areas. This study examines the potential of using stable C isotope signatures of dissolved inorganic C (δ 13 C DIC ) to track the fate of CBNG produced water after it is discharged into the impoundments. Other geochemical proxies like the major cations and major anions were used in conjunction with field water quality measurements to understand the geochemical differences between CBNG produced waters and ambient waters in the study area. Samples were collected from the CBNG discharge outfalls, produced water holding impoundments, and monitoring wells from different parts of the Powder River Basin and analyzed for δ 13 C DIC . The CBNG produced waters from outfalls and impoundments have positive δ 13 C DIC values that fall within the range of +12 per mille to +22 per mille, distinct from the ambient regional surface and

30 CFR 816.49 - Impoundments.

Science.gov (United States)

2010-07-01

..., prudent, engineering practices and any design criteria established by the regulatory authority. The... surrounding landowners for agricultural, industrial, recreational, or domestic uses. (6) The impoundment will... safely removed in accordance with current, prudent, engineering practices. Such an impoundment shall be...

50 CFR 28.42 - Impounding of domestic animals.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Impounding of domestic animals. 28.42... VIOLATIONS OF PARTS 25, 26, AND 27 Impoundment Procedures § 28.42 Impounding of domestic animals. (a) Any animal trespassing on the lands of any national wildlife refuge may be impounded and disposed of in...

Design, permitting, and construction issues associated with closure of the Panna Maria uranium tailings impoundment

International Nuclear Information System (INIS)

Strachan, C.L.; Raabe, K.L.

1997-01-01

In 1992, Panna Maria Uranium Operations (PMUO) initiated licensing and engineering activities for closure of the Panna Maria mill and 150-acre tailings impoundment located in southeast Texas. Closure of the tailings impoundment is permitted by license amendment through the Texas Natural Resources Conservation Commission (TNRCC), and based on closure criteria outlined in Texas regulations. The closure plan for the Panna Maria tailings impoundment was submitted for Texas regulatory agency review in April 1993, with details of the closure plan modified in 1994, 1995, and 1996. The closure plan included a multi-layered cover over the regraded tailings surface which was designed for long-term isolation of tailings, reduction of radon emanation to regulated levels, and reduction of infiltration to TNRCC-accepted levels. The cover and embankment slope surfaces and surrounding areas were designed to provide acceptable erosional stability as compared to runoff velocities from the Probable Maximum Precipitation event. Cover materials were selected from on-site materials and evaluated for suitability based on permeability, radon attenuation, and soil dispersivity characteristics. Off-site materials were used when necessary. The cover over the tailings has a maximum slope of 0.5 percent, and the regraded embankment slopes outside the perimeter of the impoundment have a maximum slope of 20 percent. All reclaimed slopes are covered with topsoil and revegetated. A riprap-lined channel is to be used to convey runoff from within the perimeter of the reclaimed impoundment to the north of the impoundment

36 CFR 262.11 - Impounding of dogs.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Impounding of dogs. 262.11... ENFORCEMENT SUPPORT ACTIVITIES Impoundments and Removals § 262.11 Impounding of dogs. Any dog found running at large in a part of the National Forest System, which has been closed to dogs running at large, may be...

49 CFR 193.2181 - Impoundment capacity: LNG storage tanks.

Science.gov (United States)

2010-10-01

... LIQUEFIED NATURAL GAS FACILITIES: FEDERAL SAFETY STANDARDS Design Impoundment Design and Capacity § 193.2181 Impoundment capacity: LNG storage tanks. Each impounding system serving an LNG storage tank must have a... 49 Transportation 3 2010-10-01 2010-10-01 false Impoundment capacity: LNG storage tanks. 193.2181...

Design and construction of an impoundment for precious metal mill tailings

International Nuclear Information System (INIS)

Moldt, S.F.; Miller, R.G.; Johnson, K.

1985-01-01

An engineering study and design of impoundments for the disposal of mill tailings is presented. The site is located in central Nevada, and the mill will incorporate conventional flotation followed by a carbon-in-pulp cyanide process for extraction of gold from ore. Mill process waste will be generated as flotation tailings and cyanide residue. Permeable site soils and environmental considerations required the prevention of infiltration of cyanide residue leachate into the subgrade. Geochemical modeling of flotation tailings indicated the potential for high concentration of iron and nickel to be present in the flotation tailings leachate. On-site soils were optimized for use in construction of the separate flotation tailings and cyanide residue impoundments. Embankments were constructed on compacted on-site sandy gravels. The cyanide residue impoundment was designed using a four-layer liner, utilizing all on-site soils and chemical soil additives. The liner consists of a leachate collection system over a low-permeability layer, which in turn is underlain by a leak detection drainage blanket and a low permeability subliner. The geochemical modeling performed in the analysis indicated that placement of a thin layer of oxidized surface soils, high in soluble sulfates, on the bottom of the flotation tailings impoundment would be sufficient to react with tailings leachate and cause precipitation of ferric oxide and the associated removal of nickel, permitting flotation tailings leachate to dilute acceptably with natural groundwater

30 CFR 817.84 - Coal mine waste: Impounding structures.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Impounding structures. 817.84... ACTIVITIES § 817.84 Coal mine waste: Impounding structures. New and existing impounding structures constructed of coal mine waste or intended to impound coal mine waste shall meet the requirements of § 817.81...

Characterization and assessment of potential environmental risk of tailings stored in seven impoundments in the Aries river basin, Western Romania

Science.gov (United States)

2013-01-01

Background The objective of this study was to examine the potential environmental risk of tailings resulted after precious and base metal ores processing, stored in seven impoundments located in the Aries river basin, Romania. The tailings were characterized by mineralogical and elemental composition, contamination indices, acid rock drainage generation potential and water leachability of hazardous/priority hazardous metals and ions. Multivariate statistical methods were used for data interpretation. Results Tailings were found to be highly contaminated with several hazardous/priority hazardous metals (As, Cu, Cd, Pb), and pose potential contamination risk for soil, sediments, surface and groundwater. Two out of the seven studied impoundments does not satisfy the criteria required for inert wastes, shows acid rock drainage potential and thus can contaminate the surface and groundwater. Three impoundments were found to be highly contaminated with As, Pb and Cd, two with As and other two with Cu. The tailings impoundments were grouped based on the enrichment factor, geoaccumulation index, contamination factor and contamination degree of 7 hazardous/priority hazardous metals (As, Cd, Cr, Cu, Ni, Pb, Zn) considered typical for the studied tailings. Principal component analysis showed that 47% of the elemental variability was attributable to alkaline silicate rocks, 31% to acidic S-containing minerals, 12% to carbonate minerals and 5% to biogenic elements. Leachability of metals and ions was ascribed in proportion of 61% to silicates, 11% to acidic minerals and 6% to the organic matter. A variability of 18% was attributed to leachability of biogenic elements (Na, K, Cl-, NO3-) with no potential environmental risk. Pattern recognition by agglomerative hierarchical clustering emphasized the grouping of impoundments in agreement with their contamination degree and acid rock drainage generation potential. Conclusions Tailings stored in the studied impoundments were found to

Characterization and assessment of potential environmental risk of tailings stored in seven impoundments in the Aries river basin, Western Romania

Directory of Open Access Journals (Sweden)

Levei Erika

2013-01-01

Full Text Available Abstract Background The objective of this study was to examine the potential environmental risk of tailings resulted after precious and base metal ores processing, stored in seven impoundments located in the Aries river basin, Romania. The tailings were characterized by mineralogical and elemental composition, contamination indices, acid rock drainage generation potential and water leachability of hazardous/priority hazardous metals and ions. Multivariate statistical methods were used for data interpretation. Results Tailings were found to be highly contaminated with several hazardous/priority hazardous metals (As, Cu, Cd, Pb, and pose potential contamination risk for soil, sediments, surface and groundwater. Two out of the seven studied impoundments does not satisfy the criteria required for inert wastes, shows acid rock drainage potential and thus can contaminate the surface and groundwater. Three impoundments were found to be highly contaminated with As, Pb and Cd, two with As and other two with Cu. The tailings impoundments were grouped based on the enrichment factor, geoaccumulation index, contamination factor and contamination degree of 7 hazardous/priority hazardous metals (As, Cd, Cr, Cu, Ni, Pb, Zn considered typical for the studied tailings. Principal component analysis showed that 47% of the elemental variability was attributable to alkaline silicate rocks, 31% to acidic S-containing minerals, 12% to carbonate minerals and 5% to biogenic elements. Leachability of metals and ions was ascribed in proportion of 61% to silicates, 11% to acidic minerals and 6% to the organic matter. A variability of 18% was attributed to leachability of biogenic elements (Na, K, Cl-, NO3- with no potential environmental risk. Pattern recognition by agglomerative hierarchical clustering emphasized the grouping of impoundments in agreement with their contamination degree and acid rock drainage generation potential. Conclusions Tailings stored in the studied

Responsiveness summary for the engineering evaluation/cost analysis for the proposed management of contaminated water impounded at the Weldon Spring Chemical Plant Area

International Nuclear Information System (INIS)

Maxey, M.L.; MacDonell, M.M.; Peterson, J.M.

1991-01-01

The US Department of Energy (DOE) issued the Engineering Evaluation/Cost Analysis for the Proposed Management of Contaminated Water Impounded at the Weldon Spring Chemical Plant Area in July 1990. The engineering evaluation/cost analysis (EE/CA) examines various alternatives for the proposed action to manage contaminated surface water impounded at the chemical plant area. The primary objective is to minimize potential migration of contaminants from surface impoundments to the local environment. The EE/CA addresses water currently impounded in four waste raffinate pits and two small ponds and water that will be impounded in the future as a result of upcoming response actions. Radioactive and chemical contaminants are migrating from the currently impounded water to underlying on-site groundwater via seepage and to off-site surface water via runoff. The treatment process and facilities that will be provided for management of currently impounded water can subsequently be used to manage other contaminated water in the future. Based on the evaluation of various alternatives in the EE/CA, DOE determined that the best approach for managing surface water impounded at the chemical plant area would be to remove contaminants from the water and release the treatment water to the Missouri River via a natural drainage channel. To establish requirements for releasing this treated water, DOE applied for a modification to its existing discharge permit from the Missouri Department of Natural Resources (DNR) under the National Pollutant Discharge Elimination System (NPDES) program. The EE/CA provided a major source of technical input to the application for modifying the permit. This responsiveness summary has been prepared to address the major issues identified in oral and written comments on the proposed action. 1 tab

Results of the measurement survey of elevation and environmental media in surface impoundments 3513 (B) and 3524 (A) at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Murray, M.E.; Rose, D.A.; Brown, K.S.; Coe, R.H.C. III; Lawrence, J.D.; Winton, W.

1998-07-01

A measurement survey of the elevation and environmental media in impoundments 3513 (B) and 3524 (A) at the Oak Ridge National Laboratory (ORNL) was conducted during April 1998. The investigation was performed by the Measurement Applications and Development Group of the Life Sciences Division of ORNL at the request of Bechtel Jacobs Company. Measurement activities were conducted at selected locations in order to determine the depth and appearance of the sediment and describe the clay underlying the impoundments prior to remediation. The survey was a follow-up to a previous elevation survey. The survey included the following: collection of sediment/clay cores from selected locations in each impoundment; measurement and documentation of the elevation at the water surface, at the top of sediment, at the top of clay, and at the bottom of each core; visual inspection of each core by a soil scientist to confirm the presence of clay and not material such as fly ash and soda lime compacted over the last 50 years; measurement and documentation of the background beta-gamma radiation level at the time and location of collection of each core, the highest beta-gamma level along the sediment portion of each core, and the highest beta-gamma level along the clay portion of each core; measurement and documentation of the length of the clay and of the sediment portion of each core; photographic documentation of each core; and replacement of each core in the impoundment

Effects of seasonal drawdowns on fish assemblages in sections of an impounded river-canal system in upstate New York

Science.gov (United States)

George, Scott D.; Baldigo, Barry P.; Wells, Scott M

2016-01-01

The Mohawk River and New York State Barge Canal run together as a series of permanent and temporary impoundments for most of the distance between Rome and Albany, New York. The downstream or lower section is composed of two permanent impoundments, the middle section of a series of temporary (seasonal) impoundments, and the upper section of a series of permanent impoundments. In the middle section, movable dams are lifted from the water during winter and the wetted surface area decreases by 36–56%. We used boat electrofishing during spring 2014 and 2015 to compare the relative abundance of fish populations and the composition of fish assemblages between the permanently and seasonally impounded sections of the Barge Canal and to infer the effects of the two flow management practices. A total of 3,264 individuals from 38 species were captured, and total catch per unit effort (CPUE) ranged from 46.0 to 134.7 fish/h at sites in the seasonally impounded section, compared with 140.0–342.0 fish/h in the permanent lower section and 89.0–282.0 fish/h in the permanent upper section. The amount of drawdown explained 55% of the variation in total CPUE and was a highly significant predictor variable. Mean total CPUE in the seasonally impounded section was significantly lower (by about 50%) than that in either permanently impounded section, and the assemblage composition differed significantly between sections. The relative abundance of many lentic species was markedly lower in the seasonally impounded section, while the relative abundance of several native cyprinids and the percentage of individuals belonging to species that are native to the watershed was greater in this section. Overall, these findings suggest that winter dam removal in impounded rivers may reduce the abundance of fish but may also create more natural riverine conditions that favor some native species.

Dewatering tailings impoundments : interior drains

International Nuclear Information System (INIS)

Charlie, W.A.; Doehring, D.O.; Durnford, D.S.

1984-01-01

For the design of a new uranium tailings impoundment in the western United States, it was proposed that an interior drainage system be considered to economically and reliably minimize potential short- and long-term environmental impacts. The objectives were to decrease the effective hydraulic head on the clay liner, to dewater and stabilize the tailings, and to increase the amount of water recycled to the mill. In addition, desaturation of the impoundment would induce capillary pressure (negative porewater pressure), further reducing the potential movement of dissolved pollutants. This paper presents saturated and unsaturated seepage principles and reviews the concept, criteria and design of the various interior drainage systems considered

Distribution and migration of pesticide residues in mosquito control impoundments St. Lucie County, Florida, USA

Science.gov (United States)

Parkinson, R. W.; Wang, T. C.; White, J. R.; David, J. R.; Hoffman, M. E.

1993-09-01

This project was designed to: (1) document the distribution and migration of organochlorine pesticide residues within marsh substrates of 18 St. Lucie County mosquito control impoundments located along the Indian River Lagoon estuary, and (2) evaluate the impact of water management techniques on residue mobility. Our results indicate that detectible concentrations of organochlorine compounds, applied between the late 1940s and early 1950s, are present in 16 of the 18 St. Lucie County mosquito control impoundments. These compounds are primarily restricted to the surficial, organic-rich wetland sediment, which, based upon geotechnical analysis, was exposed to the atmosphere at a time when the impoundments were subjected to pesticide treatment. Contaminated sediments are present below the surficial, organic-rich layer, suggesting that some vertical migration of pesticides has occurred. It is unlikely that leaching associated with the downward percolation of impounded water was responsible for this migration as pesticide residues were never detected within the in situ pore waters. An alternative explanation is that biological processes (e.g., rooting, burrowing) facilitated the downward flux of organochlorine compounds into sediment horizons not subjected to direct treatment. Eighty-eight surface water samples obtained from two impoundments subjected to contrasting water management techniques were analyzed for pesticide content. None of the surficial water samples collected in association with these impoundments contained detectible concentrations of organochlorine compounds. These samples were unfiltered and contained as much as 25 mg/1 of particulate organic matter. This suggests that the currently preferred management technique (RIM), which is designed to maintain water quality, limit mosquito production, and provide for ecological continuity, does not hydraulically mobilize pesticide residues into the Indian River Lagoon estuary.

Probabilistic risk assessment for the Sandia National Laboratories Technical Area V Liquid Waste Disposal System surface impoundments

International Nuclear Information System (INIS)

Dawson, L.A.; Eidson, A.F.

1996-01-01

A probabilistic risk assessment was completed for a former radioactive waste disposal site. The site, two unlined surface impoundment, was designed as part of the Liquid Waste Disposal System (LWDS) to receive radioactive effluent from nuclear reactors in Technical Area-V (TA-V) at Sandia National Laboratories/New Mexico (SNL/NM). First, a statistical comparison of site sampling results to natural background, using EPA methods, and a spatial distribution analysis were performed. Risk assessment was conducted with SNL/NM's Probabilistic Risk Evaluation and Characterization Investigation System model. The risk assessment indicated that contamination from several constituents might have been high enough to require remediation. However, further analysis based on expected site closure activities and recent EPA guidance indicated that No Further Action was acceptable

Gully potential in soil-covered uranium waste impoundments

International Nuclear Information System (INIS)

Abt, S.R.; Hogan, S.A.; Johnson, T.L.

1994-01-01

Soil covers are routinely considered a design alternative to stabilize uranium waste impoundments. Gully intrusion into the cover is one of the greatest potential threats to the long-term stability of an impoundment. An investigation was conducted to estimate the maximum depth of gully intrusion, the approximate top width of the gully at the point of maximum incision, and the approximate location of the maximum intrusion. A large-scale laboratory study was conducted on seven embankments in which approximately 200 years of rainfall was simulated and the resulting gullies were documented. In addition, 11 gullies occurring in actual reclaimed impoundments were documented. An analysis of the laboratory and field data sets was performed in which the maximum depth of gully incision, top width of the gully, and location of the maximum gully incision were related to the pile height, tributary volume of runoff, and soil composition. These relations provide the designers with a means for assessing the cover design to meet the long-term stability of the waste

Influence of lake surface area and total phosphorus on annual bluegill growth in small impoundments of central Georgia

Science.gov (United States)

Jennings, Cecil A.; Sundmark, Aaron P.

2017-01-01

The relationships between environmental variables and the growth rates of fishes are important and rapidly expanding topics in fisheries ecology. We used an informationtheoretic approach to evaluate the influence of lake surface area and total phosphorus on the age-specific growth rates of Lepomis macrochirus (Bluegill) in 6 small impoundments in central Georgia. We used model averaging to create composite models and determine the relative importance of the variables within each model. Results indicated that surface area was the most important factor in the models predicting growth of Bluegills aged 1–4 years; total phosphorus was also an important predictor for the same age-classes. These results suggest that managers can use water quality and lake morphometry variables to create predictive models specific to their waterbody or region to help develop lake-specific management plans that select for and optimize local-level habitat factors for enhancing Bluegill growth.

Evaluation of Co and Cr mobility in soil profiles collected in a scrapyard of impounded vehicles

International Nuclear Information System (INIS)

Lange, Camila N.; Figueiredo, Ana Maria G.; Enzweiler, Jacinta

2015-01-01

The number of motor vehicles in urban environments has increased dramatically in the past years. As a result, so has the number of impounded and end-of-life vehicles. Car wastes can have a very high metal content, which can cause important environmental impacts to the soil where these vehicles are kept. Most Brazilian vehicle impound scrapyards are currently operating at their maximum capacity and soils may have become contaminated by past or current vehicle handling practices. Most of these areas do not present an impermeable surface. The level of soil contamination with heavy metals depends on the type of soil, climate and management practices. Metals, such as Co and Cr, that are present in many auto-parts, may be considered potentially toxic elements in these areas. The aim of this study was to evaluate Co and Cr levels and behavior in soil profiles located in a scrapyard of impounded vehicles of Ribeirao Pires-SP city. For this purpose, samples from distinct horizons of three soil profiles were collected. Element concentrations were determined by Instrumental Neutron Activation Analysis (INAA). Soil parameters such as pH, organic matter content and clay, silt and sand percentage were also determined. The obtained data were statistically analyzed in order to establish correlations between elemental concentrations and the impounded vehicles scrapyard soil. Soil acidity showed to be the most remarkable property for Cr and Co mobility through soil profile. (author)

Evaluation of Co and Cr mobility in soil profiles collected in a scrapyard of impounded vehicles

Energy Technology Data Exchange (ETDEWEB)

Lange, Camila N.; Figueiredo, Ana Maria G., E-mail: clange@usp.br, E-mail: anamaria@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Enzweiler, Jacinta, E-mail: jacinta@ige.unicamp.br [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Instituto de Geociencias

2015-07-01

The number of motor vehicles in urban environments has increased dramatically in the past years. As a result, so has the number of impounded and end-of-life vehicles. Car wastes can have a very high metal content, which can cause important environmental impacts to the soil where these vehicles are kept. Most Brazilian vehicle impound scrapyards are currently operating at their maximum capacity and soils may have become contaminated by past or current vehicle handling practices. Most of these areas do not present an impermeable surface. The level of soil contamination with heavy metals depends on the type of soil, climate and management practices. Metals, such as Co and Cr, that are present in many auto-parts, may be considered potentially toxic elements in these areas. The aim of this study was to evaluate Co and Cr levels and behavior in soil profiles located in a scrapyard of impounded vehicles of Ribeirao Pires-SP city. For this purpose, samples from distinct horizons of three soil profiles were collected. Element concentrations were determined by Instrumental Neutron Activation Analysis (INAA). Soil parameters such as pH, organic matter content and clay, silt and sand percentage were also determined. The obtained data were statistically analyzed in order to establish correlations between elemental concentrations and the impounded vehicles scrapyard soil. Soil acidity showed to be the most remarkable property for Cr and Co mobility through soil profile. (author)

The hydrogeochemistry of four inactive tailings impoundments: Perspectives on tailings pore-water evolution

International Nuclear Information System (INIS)

Blowes, D.W.; Cherry, J.A.; Reardon, E.J.

1987-01-01

Extensive hydrogeochemical investigations are currently underway at three inactive tailings impoundments in Canada. These programs include detailed measurements of pore-water and gas-phase geochemistry through the vadose zone and the groundwater zone. An extensive piezometer network has been installed at each location to monitor the groundwater flow regime. All of the impoundments studied have been inactive for 15 to 25 years, sufficient time for extensive tailings pore-water evolution. The study areas include a very high-sulfide impoundment, a low-sulfide, high-carbonate impoundment, a low-sulfide, very low-carbonate impoundment, and a moderately high-sulfide impoundment. The pore water at each of the sites has evolved in a distinctly different and characteristic manner, representing broad styles of tailings pore-water evolution. At the high sulfide impoundment the oxidation of sulfide minerals has resulted in low pH, high redox potential conditions, with Fe 2+ concentrations in excess of 60,000 mg/L. At a depth of about 40 cm a 10 cm thick layer of ferrous and calcium sulfate minerals has precipitated. This hardpan layer limits the downward movement of O 2 and infiltrating pore waters. As a result, the pore water chemistry, both above and below the hardpan layer, has remained relatively unchanged over the past 10 years. The low-sulfide, high-carbonate tailings are sufficiently well buffered that no low pH conditions are present. The high pH conditions limit the concentrations of the metals released by sulfide mineral oxidation to levels that are two or three orders of magnitude less than is observed at the high-sulfide site. Pore waters at the low-sulfide, low-carbonate site were sampled by other researchers from the University of Waterloo

25 CFR 700.727 - Impoundment and disposal of unauthorized livestock.

Science.gov (United States)

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Impoundment and disposal of unauthorized livestock. 700... RELOCATION PROCEDURES New Lands Grazing § 700.727 Impoundment and disposal of unauthorized livestock. Unauthorized livestock within any range unit of the New Lands which are not removed therefrom within the...

25 CFR 168.16 - Impoundment and disposal of unauthorized livestock.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Impoundment and disposal of unauthorized livestock. 168... REGULATIONS FOR THE HOPI PARTITIONED LANDS AREA § 168.16 Impoundment and disposal of unauthorized livestock. Unauthorized livestock within any range unit of the Hopi Partitioned Lands which are not removed therefrom...

Groundwater monitoring at three Oak Ridge National Laboratory inactive waste impoundments: results after one year

Energy Technology Data Exchange (ETDEWEB)

Francis, C. W.; Stansfield, R. G.

1986-10-01

To determine if the migration of potential contaminants from three inactive waste impoundments at Oak Ridge National Laboratory poses a threat to groundwater quality, at least one upgradient groundwater monitoring well and threee downgradient monitoring wells were installed at each impoundment in early 1985. These three unlined impoundments, formerly used to collect and, in some instances, treat wastewater are: the 3513 impoundment; the Old Hydrofracture Facility (OHF) impoundment; and the Homogeneous Reactor Experimnt No. 2 impoundment. Groundwater samples were collected quarterly for one year. Analyses were conducted for the groundwater protection parameters promulgated by the Resource Conservation and Recovery Act. The groundwater samples were also analyzed for polychlorinated biphenyls, copper, nickel, zinc, /sup 90/Sr, /sup 137/Cs, and tritium. The contaminants found most often to affect groundwater quality at all three waste impoundments were radionuclides. For example, mean concentrations of gross beta and gross alpha activity exceeded drinking water limits at all three sites. The gross beta limit was exceeded at the 3513 and OHF impoundments by either /sup 90/Sr or tritium levels. At the 3513 impoundment, there was substantial evidence that the downgradient groundwater has been contaminated by chromium and lead and possibly by halogenated organic compounds. At the OHF impoundment, the mean level of tritium measured in the upgradient well (about 91,000 Bq/L as compared with 80,000 Bq/L in the downgradient wells) indicated that the groundwater quality has been affected by the radioactive wastes buried in the low-level radioactive waste burial ground solid waste storage area-5 upgradient of the impoundment. Testing for groundwater contamination, disclosed statistically significant contamination at all three sites.

Groundwater monitoring at three Oak Ridge National Laboratory inactive waste impoundments: results after one year

International Nuclear Information System (INIS)

Francis, C.W.; Stansfield, R.G.

1986-10-01

To determine if the migration of potential contaminants from three inactive waste impoundments at Oak Ridge National Laboratory poses a threat to groundwater quality, at least one upgradient groundwater monitoring well and threee downgradient monitoring wells were installed at each impoundment in early 1985. These three unlined impoundments, formerly used to collect and, in some instances, treat wastewater are: the 3513 impoundment; the Old Hydrofracture Facility (OHF) impoundment; and the Homogeneous Reactor Experimnt No. 2 impoundment. Groundwater samples were collected quarterly for one year. Analyses were conducted for the groundwater protection parameters promulgated by the Resource Conservation and Recovery Act. The groundwater samples were also analyzed for polychlorinated biphenyls, copper, nickel, zinc, 90 Sr, 137 Cs, and tritium. The contaminants found most often to affect groundwater quality at all three waste impoundments were radionuclides. For example, mean concentrations of gross beta and gross alpha activity exceeded drinking water limits at all three sites. The gross beta limit was exceeded at the 3513 and OHF impoundments by either 90 Sr or tritium levels. At the 3513 impoundment, there was substantial evidence that the downgradient groundwater has been contaminated by chromium and lead and possibly by halogenated organic compounds. At the OHF impoundment, the mean level of tritium measured in the upgradient well (about 91,000 Bq/L as compared with 80,000 Bq/L in the downgradient wells) indicated that the groundwater quality has been affected by the radioactive wastes buried in the low-level radioactive waste burial ground solid waste storage area-5 upgradient of the impoundment. Testing for groundwater contamination, disclosed statistically significant contamination at all three sites

Run-of-River Impoundments Can Remain Unfilled While Transporting Gravel Bedload: Numerical Modeling Results

Science.gov (United States)

Pearson, A.; Pizzuto, J. E.

2015-12-01

Previous work at run-of-river (ROR) dams in northern Delaware has shown that bedload supplied to ROR impoundments can be transported over the dam when impoundments remain unfilled. Transport is facilitated by high levels of sand in the impoundment that lowers the critical shear stresses for particle entrainment, and an inversely sloping sediment ramp connecting the impoundment bed (where the water depth is typically equal to the dam height) with the top of the dam (Pearson and Pizzuto, in press). We demonstrate with one-dimensional bed material transport modeling that bed material can move through impoundments and that equilibrium transport (i.e., a balance between supply to and export from the impoundment, with a constant bed elevation) is possible even when the bed elevation is below the top of the dam. Based on our field work and previous HEC-RAS modeling, we assess bed material transport capacity at the base of the sediment ramp (and ignore detailed processes carrying sediment up and ramp and over the dam). The hydraulics at the base of the ramp are computed using a weir equation, providing estimates of water depth, velocity, and friction, based on the discharge and sediment grain size distribution of the impoundment. Bedload transport rates are computed using the Wilcock-Crowe equation, and changes in the impoundment's bed elevation are determined by sediment continuity. Our results indicate that impoundments pass the gravel supplied from upstream with deep pools when gravel supply rate is low, gravel grain sizes are relatively small, sand supply is high, and discharge is high. Conversely, impoundments will tend to fill their pools when gravel supply rate is high, gravel grain sizes are relatively large, sand supply is low, and discharge is low. The rate of bedload supplied to an impoundment is the primary control on how fast equilibrium transport is reached, with discharge having almost no influence on the timing of equilibrium.

Effect of ship locking on sediment oxygen uptake in impounded rivers

DEFF Research Database (Denmark)

Lorke, A.; McGinnis, D. F.; Maeck, A.

2012-01-01

In the majority of large river systems, flow is regulated and/or otherwise affected by operational and management activities, such as ship locking. The effect of lock operation on sediment-water oxygen fluxes was studied within a 12.9 km long impoundment at the Saar River (Germany) using eddy....... Additional means by which the oxygen budget of the impoundment is affected by lock-induced flow variations are discussed. Citation: Lorke, A., D. F. McGinnis, A. Maeck, and H. Fischer (2012), Effect of ship locking on sediment oxygen uptake in impounded rivers, Water Resour. Res., 48, W12514, doi: 10....... These wave-induced flow variations cause variations in sediment-water oxygen fluxes. While the mean flux during time periods without lock operation was 0.5 +/- 0.1 g m(-2) d(-1), it increased by about a factor of 2 to 1.0 +/- 0.5 g m(-2) d(-1) within time periods with ship locking. Following the daily...

The impact of impoundment on the rotifer communities in two tropical floodplain environments: interannual pulse variations

Directory of Open Access Journals (Sweden)

CC. Bonecker

Full Text Available Hydrological pulses are the main factor regulating the structure of biological communities in floodplains. Reservoirs above this ecosystem change the environment's dynamics and the community's biodiversity. This study evaluated the structure and stability of the rotifer community in response to changes in hydrological pulses after the Porto Primavera impoundment in the Upper Paraná River floodplain. The community was studied in a river and in a floodplain lake downstream of the dam over a four-year period before and after the impoundment. A decrease in species richness and abundance was observed soon after the impoundment, followed by an increase in these attributes and in specific diversity when the hydrometric level of the Paraná River rose and, consequently, increased the connectivity between the floodplain environments. Conochilus coenobasis, Filinia longiseta, Keratella cochlearis, Lecane proiecta and Polyarthra dolichoptera persisted throughout the study and contributed to community stability (the maintenance of rank in species abundance over time, which was high in the floodplain lake, mainly after the impoundment. Reductions in the frequency, intensity and amplitude of potamophase pulses after the impoundment led to the decrease in species richness and the increases in abundance, community stability, and species diversity, which determine community resilience.

Evaluation of Major Dike-Impounded Ground-Water Reservoirs, Island of Oahu

Science.gov (United States)

Takasaki, Kiyoshi J.; Mink, John Francis

1985-01-01

Ground-water reservoirs impounded by volcanic dikes receive a substantial part of the total recharge to ground water on the island of Oahu because they generally underlie the rainiest areas. These reservoirs accumulate the infiltration from rainfall, store it temporarily, and steadily leak it to abutting basal reservoirs or to streams cutting into them. The dike reservoirs have high hydraulic heads and are mostly isolated from saline water. The most important and productive of the dike-impounded reservoirs are in an area of about 135 square miles in the main fissure zone of the Koolau volcano where the top of the dike-impounded water reaches an altitude of at least 1,000 feet. Water is impounded and stored both above and below sea level. The water stored above sea level in the 135 square mile area has been roughly estimated at 560 billion gallons. In comparison, the water stored above sea level in reservoirs underlying a dike-intruded area of about 53 square miles in the Waianae Range has been roughly estimated at 100 billion gallons. Storage below sea level is indeterminable, owing to uncertainties about the ability of the rock to store water as dike density increases and porosity decreases. Tunnels, by breaching dike controls, have reduced the water stored above sea level by at least 50 billion gallons in the Koolau Range and by 5 1/2 billion gallons in the Waianae Range, only a small part of the total water stored. Total leakage from storage in the Koolau Range has been estimated at about 280 Mgal/d (million gallons per day). This estimated leakage from the dike-impounded reservoirs makes up a significant part of the ground-water yield of the Koolau Range, which has been estimated to range from 450 to 580 Mgal/d. The largest unused surface leakage is in the Kaneohe, Kahana, and Punaluu areas, and the largest unused underflow occurs in the Waialee, Hauula-Laie, Punaluu, and Kahana areas. The unused underflow leakage is small in areas near and east of Waialae, but

30 CFR 817.49 - Impoundments.

Science.gov (United States)

2010-07-01

... runoff from the design precipitation event when it is demonstrated by the operator and certified by a... constructed to safely pass the applicable design precipitation event specified in paragraph (a)(9)(ii) of this... this section, the required design precipitation event for an impoundment meeting the spillway...

French Modular Impoundment: Final Cost and Performance Evaluation

Energy Technology Data Exchange (ETDEWEB)

Drown, Peter [French Development Enterprises, LLC, North Billerica, MA (United States); French, Bill [French Development Enterprises, LLC, North Billerica, MA (United States)

2017-05-17

This report comprises the Final Cost and Performance Report for the Department of Energy Award # EE0007244, the French Modular Impoundment (aka the “French Dam”.) The French Dam is a system of applying precast modular construction to water control structures. The “French Dam” is a term used to cover the construction means/methods used to construct or rehabilitate dams, diversion structures, powerhouses, and other hydraulic structures which impound water and are covered under FDE’s existing IP (Patents # US8414223B2; US9103084B2.)

Sedimentation in Lake Onalaska, Navigation Pool 7, upper Mississippi River, since impoundment

Science.gov (United States)

Korschgen, C.E.; Jackson, G.A.; Muessig, L.F.; Southworth, D.C.

1987-01-01

Sediment accumulation was evaluated in Lake Onalaska, a 2800-ha backwater impoundment on the Upper Mississippi River. Computer programs were used to process fathometric charts and generate an extensive data set on water depth for the lake. Comparison of 1983 survey data with pre-impoundment (before 1937) data showed that Lake Onalaska had lost less than 10 percent of its original mean depth in the 46 years since impoundment. Previous estimates of sedimentation rates based on Cesium-137 sediment core analysis appear to have been too high. (DBO)

The Authority of the President to Impound Funds Appropriated by Congress.

Science.gov (United States)

Adams, James R.

During fiscal year 1973, President Nixon ordered the impoundment of about 18 billion dollars in Federal funds for domestic programs. A large portion of that amount was used to slash federal funding for education programs. The entire impoundment controversy revolves around the doctrine of separation of powers. Insofar as the President has refused…

Diet and trophic structure of the fish fauna in a subtropical ecosystem: impoundment effects

Directory of Open Access Journals (Sweden)

Rosilene Luciana Delariva

Full Text Available This study examined the diet and trophic structure of the fish fauna, over temporal and spatial scales, as affected by the impoundment of the Iguaçu River in the region of Salto Caxias, Paraná State, Brazil. Sampling was conducted before (March 1997 - February 1998 and after the impoundment (March 1999 - February 2000, at four sampling sites. The stomach contents were analyzed by the volumetric method. The species could be organized in 10 trophic guilds: algivores, carcinophages, detritivores, herbivores, aquatic insectivores, terrestrial insectivores, invertivores, omnivores, piscivores, and planktivores; the first and last guilds were represented only in the post-impoundment period. Similarity patterns and feeding changes were summarized by a non-metric Multi-dimensional Scaling (nMDS analysis and statistically tested by a Permutational multivariate analysis of variance (PERMANOVA. Most species showed feeding changes, except for the piscivores and detritivores. These changes were related to the temporal factor (impoundment phases, such as reduced intake of benthic organisms and allochthonous food, which were usually replaced by resources from the reservoir itself (algae, microcrustaceans, and fish, simplifying the food spectrum of the fish fauna. A different indicator of food resources (IndVal corroborated these changes in the feeding of the species. The proportions of the trophic guilds evaluated based on the catch per unit of effort (CPUE and tested by ANOSIM were significantly different before and after the impoundment. Herbivores and piscivores were the guilds that contributed (SIMPER to these differences, especially the high increase in biomass of the piscivore guild after the impoundment. Variations in the abundance of trophic guilds were more directly related to changes in the feeding habits of the fish fauna than to increases in the number and biomass of the species that constitute these guilds.

Assessment of sediments in the riverine impoundments of national wildlife refuges in the Souris River Basin, North Dakota

Science.gov (United States)

Tangen, Brian A.; Laubhan, Murray K.; Gleason, Robert A.

2014-01-01

Accelerated sedimentation of reservoirs and riverine impoundments is a major concern throughout the United States. Sediments not only fill impoundments and reduce their effective life span, but they can reduce water quality by increasing turbidity and introducing harmful chemical constituents such as heavy metals, toxic elements, and nutrients. U.S. Fish and Wildlife Service national wildlife refuges in the north-central part of the United States have documented high amounts of sediment accretion in some wetlands that could negatively affect important aquatic habitats for migratory birds and other wetland-dependent wildlife. Therefore, information pertaining to sediment accumulation in refuge impoundments potentially is important to guide conservation planning, including future management actions of individual impoundments. Lands comprising Des Lacs, Upper Souris, and J. Clark Salyer National Wildlife Refuges, collectively known as the Souris River Basin refuges, encompass reaches of the Des Lacs and Souris Rivers of northwestern North Dakota. The riverine impoundments of the Souris River Basin refuges are vulnerable to sedimentation because of the construction of in-stream dams that interrupt and slow river flows and because of post-European settlement land-use changes that have increased the potential for soil erosion and transport to rivers. Information regarding sediments does not exist for these refuges, and U.S. Fish and Wildlife Service personnel have expressed interest in assessing refuge impoundments to support refuge management decisions. Sediment cores and surface sediment samples were collected from impoundments within Des Lacs, Upper Souris, and J. Clark Salyer National Wildlife Refuges during 2004–05. Cores were used to estimate sediment accretion rates using radioisotope (cesium-137 [137Cs], lead-210 [210Pb]) dating techniques. Sediment cores and surface samples were analyzed for a suite of elements and agrichemicals, respectively. Examination of

32 CFR 634.51 - Procedures for impoundment.

Science.gov (United States)

2010-07-01

... complete DD Form 2506 (Vehicle Impoundment Report) as a record of the actions taken. (i) An inventory... not be inventoried. Such articles should be opened only if necessary to identify the owner of the...

Using Helicopter Electromagnetic Surveys to Identify Potential Hazards at Mine Waste Impoundments

Energy Technology Data Exchange (ETDEWEB)

Hammack, R.W.

2008-01-01

In July 2003, helicopter electromagnetic surveys were conducted at 14 coal waste impoundments in southern West Virginia. The purpose of the surveys was to detect conditions that could lead to impoundment failure either by structural failure of the embankment or by the flooding of adjacent or underlying mine works. Specifically, the surveys attempted to: 1) identify saturated zones within the mine waste, 2) delineate filtrate flow paths through the embankment or into adjacent strata and receiving streams, and 3) identify flooded mine workings underlying or adjacent to the waste impoundment. Data from the helicopter surveys were processed to generate conductivity/depth images. Conductivity/depth images were then spatially linked to georeferenced air photos or topographic maps for interpretation. Conductivity/depth images were found to provide a snapshot of the hydrologic conditions that exist within the impoundment. This information can be used to predict potential areas of failure within the embankment because of its ability to image the phreatic zone. Also, the electromagnetic survey can identify areas of unconsolidated slurry in the decant basin and beneath the embankment. Although shallow, flooded mineworks beneath the impoundment were identified by this survey, it cannot be assumed that electromagnetic surveys can detect all underlying mines. A preliminary evaluation of the data implies that helicopter electromagnetic surveys can provide a better understanding of the phreatic zone than the piezometer arrays that are typically used.

Profiling of Sediment Microbial Community in Dongting Lake before and after Impoundment of the Three Gorges Dam

Directory of Open Access Journals (Sweden)

Wei Huang

2016-06-01

Full Text Available The sediment microbial community in downstream-linked lakes can be affected by the operation of large-scale water conservancy projects. The present study determined Illumina reads (16S rRNA gene amplicons to analyze and compare the bacterial communities from sediments in Dongting Lake (China before and after impoundment of the Three Gorges Dam (TGD, the largest hydroelectric project in the world. Bacterial communities in sediment samples in Dongting Lake before impoundment of the TGD (the high water period had a higher diversity than after impoundment of the TGD (the low water period. The most abundant phylum in the sediment samples was Proteobacteria (36.4%–51.5%, and this result was due to the significant abundance of Betaproteobacteria and Deltaproteobacteria in the sediment samples before impoundment of the TGD and the abundance of Gammaproteobacteria in the sediment samples after impoundment of the TGD. In addition, bacterial sequences of the sediment samples are also affiliated with Acidobacteria (11.0% on average, Chloroflexi (10.9% on average, Bacteroidetes (6.7% on average, and Nitrospirae (5.1% on average. Variations in the composition of the bacterial community within some sediment samples from the river estuary into Dongting Lake were related to the pH values. The bacterial community in the samples from the three lake districts of Dongting Lake before and after impoundment of the TGD was linked to the nutrient concentration.

Sharptooth catfish shows its metal: a case study of metal contamination at two impoundments in the Olifants River, Limpopo river system, South Africa.

Science.gov (United States)

Jooste, Antoinette; Marr, Sean M; Addo-Bediako, Abraham; Luus-Powell, Wilmien J

2015-02-01

Clarias gariepinus is increasing in importance as a global aquaculture species with a 100 fold increase in production over the past decade but this species still remains one of the most important wild harvested freshwater food fish throughout rural Africa. However, this species has been shown to accumulate metals from contaminated inland waters. In this paper, the metal concentrations in muscle tissue of C. gariepinus from two main-stem impoundments in the Olifants River, Limpopo Basin, were measured and a desktop risk assessment based on the US-EPA methodology completed to evaluate whether long-term consumption of C. gariepinus from these impoundments may pose a health risk to rural communities. Our results show that metals are accumulating in the muscle tissue of C. gariepinus and have appeared to have increased in the last two decades. Risk assessment generated Hazard quotients (HQ) greater than 1 indicate that long term consumption of fish from these impoundments may cause adverse health impacts. We found that lead (HQ=9), antimony (HQ=14), cobalt (HQ=2) and chromium (HQ=1) at one impoundment and lead (HQ=2) at the other impoundment were above acceptable levels for weekly consumption of 150 g C. gariepinus muscle tissue. Copyright © 2014 Elsevier Inc. All rights reserved.

Evaluating the effect of vehicle impoundment policy on illegal construction and demolition waste dumping: Israel as a case study.

Science.gov (United States)

Seror, Nissim; Hareli, Shlomo; Portnov, Boris A

2014-08-01

Construction and demolition (C&D) waste dumped alongside roads and in open areas is a major source of soil and underground water pollution. Since 2006, Israeli ministry for environmental protection enacted a policy of vehicle impoundment (VI) according to which track drivers caught while dumping C&D waste illegally have their vehicles impounded. The present study attempted to determine whether the VI policy was effective in increasing the waste hauling to authorized landfill sites, thus limiting the number of illegal unloads of C&D waste at unauthorized landfill sites and in open areas. During the study, changes in the ratio between the monthly amount of C&D waste brought to authorized landfills sites and the estimated total amount of C&D waste generated in different administrative districts of Israel were examined, before and after the enactment of the 2006 VI policy. Short questionnaires were also distributed among local track drivers in order to determine the degree of awareness about the policy in question and estimate its deterrence effects. According to the study's results, in the district of Haifa, in which the VI policy was stringently enacted, the ratio between C&D waste, dumped in authorized landfill sites, and the total amount of generated C&D waste, increased, on the average, from 20% in January 2004 to 35% in October 2009, with the effect attributed to the number of vehicle impoundments being highly statistically significant (t=2.324; p0.1). The analysis of the questionnaires, distributed among the local truck drivers further indicated that the changes observed in the district of Haifa are not coincident and appeared to be linked to the VI policy's enactment. In particular, 62% of the truck drivers, participated in the survey, were aware of the policy and 47% of them personally knew a driver whose vehicle was impounded. Furthermore, the drivers estimated the relative risk of being caught for unloading C&D waste in unauthorized sites, on the average, as

Pre- and post-impoundment nitrogen in the lower Missouri River

Science.gov (United States)

Blevins, Dale W.; Wilkison, Donald H.; Niesen, Shelley L.

2013-01-01

Large water-sample sets collected from 1899 through 1902, 1907, and in the early 1950s allow comparisons of pre-impoundment and post-impoundment (1969 through 2008) nitrogen concentrations in the lower Missouri River. Although urban wastes were not large enough to detectably increase annual loads of total nitrogen at the beginning of the 20th century, carcass waste, stock-yard manure, and untreated human wastes measurably increased ammonia and organic-nitrogen concentrations during low flows. Average total-nitrogen concentrations in both periods were about 2.5 mg/l, but much of the particulate-organic nitrogen, which was the dominant form of nitrogen around 1900, has been replaced by nitrate. This change in speciation was caused by the nearly 80% decrease in suspended-sediment concentrations that occurred after impoundment, modern agriculture, drainage of riparian wetlands, and sewage treatment. Nevertheless, bioavailable nitrogen has not been low enough to limit primary production in the Missouri River since the beginning of the 20th century. Nitrate concentrations have increased more rapidly from 2000 through 2008 (5 to 12% per year), thus increasing bioavailable nitrogen delivered to the Mississippi River and affecting Gulf Coast hypoxia. The increase in nitrate concentrations with distance downstream is much greater during the post-impoundment period. If strategies to decrease total-nitrogen loads focus on particulate N, substantial decreases will be difficult because particulate nitrogen is now only 23% of total nitrogen in the Missouri River. A strategy aimed at decreasing particulates also could further exacerbate land loss along the Gulf of Mexico, which has been sediment starved since Missouri River impoundment. In contrast, strategies or benchmarks aimed at decreasing nitrate loads could substantially decrease nitrogen loadings because nitrates now constitute over half of the Missouri's nitrogen input to the Mississippi. Ongoing restoration and creation

Characterization plan for the waste holding basin (3513 impoundment)

International Nuclear Information System (INIS)

Stansfield, R.G.; Francis, C.W.

1986-09-01

US Department of Energy (DOE) facilities are required to comply fully with all federal and state regulations. In response to this requirement, the Oak Ridge National Laboratory (ORNL) has established the remedial action program, to provide comprehensive management of areas where past research, development, and waste management activities have been conducted and have resulted in residual contamination of facilities or the environment. One of the objectives of this program is to define the extent of contamination at these sites. The intent is to document the known environmental characteristics of the sites and identify the additional actions, such as sampling, analytical measurements, and modeling, necessary to confirm contamination and the possible migration of contaminants from the sites. One of these sites is the waste holding basin (3513 impoundment). The 3513 impoundment is an unlined waste settling basin constructed in 1944 for collection of ORNL wastewater before its discharge into White Oak Creek. Operation of the facility ceased in 1976 when a new process waste treatment plant came into operation. Considerable site-specific environmental information has been developed over the years relative to the type and quantities of radionuclides and hazardous substances contained in the pond water and sediment. The concentrations and patterns of distribution for many of the radionuclides in the aquatic biota as well as for the terrestrial plants growing on the berm of the impoundment have been determined by DOE ecological studies. Recently, some data were collected that evaluate the extent of contaminant movement to the groundwater. Results from these studies are summarized in this report. Also included in this report is an outline of additional tasks needed to obtain the necessary information to model the transport and dose pathways of hazardous substances from the site

Rock riprap design methods and their applicability to long-term protection of uranium mill tailings impoundments

International Nuclear Information System (INIS)

Walters, W.H.

1982-08-01

This report reviews the more accepted or recommended riprap design methods currently used to design rock riprap protection against soil erosion by flowing water. The basic theories used to develop the various methods are presented. The Riprap Design with Safety Factors Method is identified as the logical choice for uranium mill tailings impoundments. This method is compared to the other methods and its applicability to the protection requirements of tailings impoundments is discussed. Other design problems are identified and investigative studies recommended

Simulated effects of impoundment of lake seminole on ground-water flow in the upper Floridan Aquifer in southwestern Georgia and adjacent parts of Alabama and Florida

Science.gov (United States)

Jones, L. Elliott; Torak, Lynn J.

2004-01-01

Hydrologic implications of the impoundment of Lake Seminole in southwest Georgia and its effect on components of the surface- and ground-water flow systems of the lower Apalachicola?Chattahoochee?Flint (ACF) River Basin were investigated using a ground-water model. Comparison of simulation results of postimpoundment drought conditions (October 1986) with results of hypothetical preimpoundment conditions (a similar drought prior to 1955) provides a qualitative measure of the changes in hydraulic head and ground-water flow to and from streams and Lake Seminole, and across State lines caused by the impoundment. Based on the simulation results, the impoundment of Lake Seminole changed ground-water flow directions within about 20?30 miles of the lake, reducing the amount of ground water flowing from Florida to Georgia southeast of the lake. Ground-water storage was increased by the impoundment, as indicated by a simulated increase of as much as 26 feet in the water level in the Upper Floridan aquifer. The impoundment of Lake Seminole caused changes to simulated components of the ground-water budget, including reduced discharge from the Upper Floridan aquifer to streams (315 million gallons per day); reduced recharge from or increased discharge to regional ground-water flow at external model boundaries (totaling 183 million gallons per day); and reduced recharge from or increased discharge to the undifferentiated overburden (totaling 129 million gallons per day).

Investigation, assessment and remediation of the water pathway in the surroundings of the Culmitzsch A tailings impoundment

International Nuclear Information System (INIS)

Schulze, G.; Paul, M.; Priester, J.; Schoepfer, C.

1998-01-01

Several large tailings impoundments in Saxony and Thuringia are the result of the extensive uranium mining and milling in Eastern Germany after World War II. The Culmitzsch tailings pond in Eastern Thuringia was constructed within a former uranium open pit mine and is located within the Culmitzsch trench fault. The tailings impoundment includes two ponds (Culmitzsch A and B) which are separated by an internal dam with an impervious core. The Culmitzsch A pond covers an area of 158 ha, the maximum tailings thickness is 70 m. Between this pond (elevation of up to 340 m above sea-level) and the Lerchenbach creek (265.. 280 m above sea-level) a steep gradient exists. So the valley of the Lerchenbach is the general discharge area for the seepage of the pond which is a result of dewatering by gravity and consolidation. The seepage water migrates through the southern dam of the impoundment and through permeable layers which are in contact with the tailings. About 400 groundwater wells were installed within three aquifers in order to clarify the flow direction and the degree of contamination of the groundwater as well as to investigate the geohydraulic properties of the rocks in the surroundings of the pond. Based on the results of this investigation programme a three-dimensional hydrogeological model was built up which reflects the general relationships between the pond and its geological setting as well as the water balance of the whole system. Presently a catchment system exists which gathers all surface waters with significant uranium and salt concentrations. Moreover dewatering wells on the beach zone of the pond and catchment wells in the downstream area of the impoundment have been installed. Before being released to the receiving streams seepage and freewater are treated in a two-step water treatment plant in order to decrease their uranium, radium and arsenic contents. (orig.) [de

Modelling of contaminant migration in acidic groundwater plumes at uranium tailings impoundments: ADNEUT3

International Nuclear Information System (INIS)

Cherry, J.A.; Morin, K.A.; Dubrovsky, N.M.

1984-06-01

This report describes the creation and application of ADNEUT3, the latest addition to the ADNEUT (Acid-Drainage NEUTralization) family of computer programs for simulating acid-drainage transport and neutralization. The creation of ADNEUT3 involved the expansion of ADNEUT1 to allow variable input conditions such as changing input solution with time, variable initial amounts of minerals through the simulated streamtube, variable velocities through the streamtube, and variable solubilities for relevant minerals dependent on aqueous chemical composition. Concepts for simulating acid-drainage neutralization are reviewed and ADNEUT3 is then applied to a field-study site of acidic contaminant migration from the Nordic Main uranium-tailings impoundment near Elliot Lake, Ontario. A sensitivity study is first implemented to calibrate ADNEUT3 to the results of the 1979 to 1983 field studies. Then ADNEUT3 is used to define probable past conditions at the site which are not reliably known. In particular, ADNEUT3 is used to help identify: 1) the approximate year when acidic seepage began leaving the tailings impoundment (1966-1967), 2) the past chemical composition of the seepage (somewhat more acidic for a short period of time), and 3) the location of the source area within the tailings for the acidic seepage (near the impoundment dam, close to the field site). Finally, ADNEUT3 is used to predict future contaminant migration. Results indicate that hundreds of years are required under present conditions for the most acidic water with associated high levels of contaminants to migrate about 100 m from the tailings impoundment. The cause of this slow movement is the significant neutralization capacity of the aquifer. If acid production within the tailings decreases in the future, migration rates of contaminants will also decrease

An Object-Based Machine Learning Classification Procedure for Mapping Impoundments in Brazil's Amazon-Cerrado Agricultural Frontier

Science.gov (United States)

Solvik, K.; Macedo, M.; Graesser, J.; Lathuilliere, M. J.

2017-12-01

Large-scale agriculture and cattle ranching in Brazil has driving the creation of tens of thousands of small stream impoundments to provide water for crops and livestock. These impoundments are a source of methane emissions and have significant impacts on stream temperature, connectivity, and water use over a large region. Due to their large numbers and small size, they are difficult to map using conventional methods. Here, we present a two-stage object-based supervised classification methodology for identifying man-made impoundments in Brazil. First, in Google Earth Engine pixels are classified as water or non-water using satellite data and HydroSHEDS products as predictors. Second, using Python's scikit-learn and scikit-image modules the water objects are classified as man-made or natural based on a variety of shape and spectral properties. Both classifications are performed by a random forest classifier. Training data is acquired by visually identifying impoundments and natural water bodies using high resolution satellite imagery from Google Earth.This methodology was applied to the state of Mato Grosso using a cloud-free mosaic of Sentinel 1 (10m resolution) radar and Sentinel 2 (10-20m) multispectral data acquired during the 2016 dry season. Independent test accuracy was estimated at 95% for the first stage and 93% for the second. We identified 54,294 man-made impoundments in Mato Grosso in 2016. The methodology is generalizable to other high resolution satellite data and has been tested on Landsat 5 and 8 imagery. Applying the same approach to Landsat 8 images (30 m), we identified 35,707 impoundments in the 2015 dry season. The difference in number is likely because the coarser-scale imagery fails to detect small (work will apply this approach to satellite time series for the entire Amazon-Cerrado frontier, allowing us to track changes in the number, size, and distribution of man-made impoundments. Automated impoundment mapping over large areas may help with

The geo-environmental design of a coal refuse impoundment in Illinois

International Nuclear Information System (INIS)

Ripp, B.J.

1997-01-01

The coal refuse impoundment discussed was one of the first permitted under new regulatory standards within the State of Illinois. The new standards go beyond the geotechnial stability of the structure and must address the groundwater quality of the area and the impact of the impoundment on the groundwater system. The geotechnial design of the coal refuse impoundment dam and associated structures had its own particular challenges such as: 1) the construction of the structure over mined workings; 2) the close proximity of seismically active fault zones; and 3) the embankment configuration being controlled by the material balance of the mine refuse. The implementation of the groundwater protection plan included: 1) incorporating the groundwater quality standards and sampling protocols of several state agencies while the standards were being drafted; 2) sampling of the potential sources of groundwater impact; 3) establishing background levels; and 4) establishing the groundwater class. An initial groundwater transport model was developed and used as the basis for recommending a groundwater monitoring design in place of constructing a soil or synthetic liner. 15 refs., 2 figs., 3 tabs

Effects of impoundment and regulation upon the stomach contents of fish at Cow Green, Upper Teesdale

Energy Technology Data Exchange (ETDEWEB)

Crisp, D.T.; Mann, R.H.K.; McCormack, J.C.

1978-04-01

The stomach contents of 1003 brown trout, 1551 bullheads and 800 minnows taken from the reservoir basin and below the dam, before and after impoundment of the river Tees, were examined. Their composition reflected observations by other workers on river and reservoir benthos, except for the increase in numbers of Hydra and Nais below the dam, and Mollusca, Hirudinea and oligochaetes in the reservoir. Trout below the dam ate more Ephemeroptera nymphs and Chironomidae larvae but fewer terrestrial casualties after river regulation, whereas bullheads ate more Mollusca but fewer Plecoptera nymphs. In both species Baetidae nymphs increased in numerical importance relative to Ecdyonuridae. Trout, but not bullheads, took zooplankton discharged from the reservoir. Before impoundment, trout within the reservoir basin ate chiefly benthic organisms and terrestrial casualties. Inundated terrestrial material, mainly earthworms, formed the bulk of their food for at least three years after impoundment, whilst from the second year onwards Chironomidae and, in some years, Gammarus became increasingly important. Zooplankton was taken by all sizes of reservoir trout. Bullheads within the reservoir basin ate chiefly river benthos before impoundment, with Ephemeroptera and Plecoptera nymphs predominant in older fish, and aquatic Diptera and Coleoptera also important in the fry. After impoundment, Chironomidae and Gammarus were the main items taken by older bullheads, and Chironomidae and micro-crustacea by the fry. Among all sizes of minnow, Chironomidae, micro-crustacea and detritus increased in numerical importance after impoundment.

Stochastic Modelling of the Hydraulic Anisotropy of Ash Impoundment Sediment

Science.gov (United States)

Slávik, Ivan

2017-12-01

In the case reported here the impoundments of a 400 MW coal heated power plant with an annual production of about 1.5 million tons of fuel ash are of the cross-valley type, operated by the simple and cheap „upstream method”. The aim of the research was to determine overall and local values of the permeability in horizontal as well as in vertical direction and the anisotropy of the thin-layered sedimented ash. The coal ashes are hydraulically transported through pipelines in form of a slurry and periodically floated on the beach of the impoundment. The ashes are deposited in the form of a thin-layered sediment, with random alternation of layers with a coarser or finer granularity. The ash impoundment sediment is anthropogenic sediment with horizontally laminated texture. Therefore, the sediment is anisotropic from the viewpoint of water seepage. The knowledge of the permeability and the seepage anisotropy of the sediment is a basic requirement for the design of an appropriate dewatering system. The seepage anisotropy of the ash sediment has been checked by means of stochastic modelling, based on the correlation between the effective grain diameter and the coefficient of permeability of the ash: the effective grain diameter and the thickness of individual layers have been proposed to be random events.

The fish community of a small impoundment in upstate New York

Science.gov (United States)

McCoy, C. Mead; Madenjian, Charles P.; Adams, Jean V.; Harman, Willard N.

2001-01-01

Moe Pond is a dimictic impoundment with surface area of 15.6 ha, a mean depth of 1.8 m, and an unexploited fish community of only two species: brown bullhead (Ameiurus nebulosus) and golden shiner (Notemigonus crysoleucas). The age-1 and older brown bullhead population was estimated to be 4,057 individuals, based on the Schnabel capture-recapture method of population estimation. Density and biomass were respectively estimated at 260 individuals/ha and 13 kg/ha. Annual survival rate of age-2 through age-5 brown bullheads was estimated at 48%. The golden shiner length-frequency distribution was unimodal with modal length of 80 mm and maximum total length of 115 m. The golden shiner population estimate was 7,154 individuals, based on seven beach seine haul replicate samples; the density and biomass were 686 shiners/ha and 5 kg/ha, respectively. This study provides an information baseline that may be useful in understanding food web interactions and whole-pond nutrient flux.

Moist Soil Management of Wetland Impoundments for Plants and Invertebrates

Data.gov (United States)

Department of the Interior — In year’s past an impoundment was drained (a drawdown) when floating-leaved plants covered more than 50% of the water area. Drawdowns encourage beneficial moist soil...

Engineering evaluation/cost analysis for the proposed management of contaminated water impounded at the Weldon Spring chemical plant area

International Nuclear Information System (INIS)

MacDonell, M.M.; Maxey, M.L.; Peterson, J.M.; Joya, I.E.

1990-07-01

This engineering evaluation/cost analysis (EE/CA) report has been prepared to support the proposed removal action for managing contaminated surface waters impounded at the chemical plant area of the Weldon Spring site, located near Weldon Spring, Missouri. The US Department of Energy is responsible for cleanup activities at the site under its Surplus Facilities Management Program (SFMP). The major goals of SFMP are to eliminate potential hazards to human health and the environment that are associated with contamination at SFMP sites and to make surplus real property available for other uses, to the extent possible. The objectives of this EE/CA report are to identify the cleanup as a removal action, document the selection of a response that will mitigate the potential release of radioactive or chemical contaminants from the impounded waters into the nearby environment, and address environmental impacts associated with the proposed action. 41 refs., 8 figs., 8 tabs

Water-quality study of Tulpehocken Creek, Berks County, Pennsylvania, prior to impoundment of Blue Marsh Lake

Science.gov (United States)

Barker, James L.

1977-01-01

Blue Marsh Lake is planned as a multipurpose impoundment to be constructed on Tulpehocken Creek near Bernville, Berks County, Pennsylvania. Prior to construction, samples of water, bed material, and soil were collected throughout the impoundment site to determine concentrations of nutrients, insecticides, trace metals, suspended sediment, and bacteria. Analyses of water suggest the Tulpehocken Creek basin to be a highly fertile environment. Nitrogen and phosphorus concentrations near the proposed dam site had median values of 4.5 and 0.13 mg/L, respectively. Suspended sediment discharges average between 100 and 200 tons (90.7 to 181.4 metric tons) per day during normal flows but may exceed 10,000 tons (9,070 metric tons) per day during storm runoff. Highest yields were measured during winter and early spring. Concentrations range from 3 mg/L to more than 500 mg/L. Bed material samples contain trace quantities of aldrin, DDT, DDD, DDE, dieldrin, and chlordane. Polychlorinated biphyenyls (PCB's) ranged from 10 to 100 μg/kg. Soils at the impoundment site are of average fertility. However, the silt loam texture is ideal for attachment and growth of aquatic plants. Bacteria populations indicative of recent fecal contamination are prevalent in the major inflows to the proposed lake. Fecal Coliform exceeded the standards recommended by the Federal Water Pollution Administration Committee on Water Quality Criteria for public water supply in 29 percent of the monthly samples, and exceeded the recommended public bathing waters standard in 83 percent of the samples collected from June to September. Arsenic from an industrial waste was found in the water, suspended sediment, and bed material of Tulpehocken Creek in concentrations of 0 to 30 μg/l, 2 to 879 μg/l, and 1 to 79 μg/g, respectively. It represents a potential environmental hazard; however, the measured concentrations are less than that known to be harmful to man, fish, or wildlife, according to published water

The use of artificial impoundments by two amphibian species in the Delaware Water Gap National Recreation Area

Science.gov (United States)

Julian, J.T.; Snyder, C.D.; Young, J.A.

2006-01-01

We compared breeding activity of Ambystoma maculatum (Spotted Salamander) and Rana sylvatica (Wood Frog) in artificial impoundments to patterns in natural wetlands over a three-year period in the Delaware Water Gap National Recreation Area. Rana sylvatica were 5.6 times more likely to use natural bodies of water for breeding than artificial impoundments, while A. maculatum were 2.7 times more likely to use natural bodies of water. Both species were approximately 9 times more likely to breed in fishless bodies of water than in waters with predatory fish. Ambystoma maculatum were 6 times more likely to breed in wetlands with more stable seasonal hydroperiods, while R. sylvatica were only 2 times more likely to do so. We conclude that the high likelihood of fish presence in impoundments was the primary explanation for why both species were less likely to use impoundments than natural wetlands, while the tendency of A. maculatum to avoid natural wetlands with shorter hydroperiods explained why differences in use between pond types was more pronounced for R. sylvatica.

The Impact of Impoundment on Mercury Bioaccumulation in Fish Downstream from a Newly Constructed Reservoir, Wujiang River, Southwest China.

Science.gov (United States)

Li, Sixin; Zhou, Lianfeng; Chang, Jianbo; Yang, Zhi; Hu, Juxiang; Hongjun, Wang

2017-11-01

Mercury concentrations in fish were investigated downstream from a newly impounded subtropical reservoir in August 2008. After 6-7 months of reservoir impoundment, mean mercury concentration in fish from downstream is significantly increased by 1.9 times. Not only carnivorous fish but also benthic fish had significantly higher total mercury concentrations than others. No significant correlation was found between total mercury concentrations and body length or weight of 13 fish species. Compared with the pre-impoundment, total mercury in fish from downstream is significantly increased by reservoir impoundment, but the increased rate is lower than those in subarctic and temperate areas. Fish samples surpassed the Chinese hygienic standard for tolerances of mercury in foods increased by 4.3%. More attention should be given to fish mercury levels from downstream sites to prevent possible adverse effects on the health of local people.

Restoration of Tidal Flow to Impounded Salt Marsh Exerts Mixed Effect on Leaf Litter Decomposition

Science.gov (United States)

Henry, B. A.; Schade, J. D.; Foreman, K.

2015-12-01

Salt marsh impoundments (e.g. roads, levees) disconnect marshes from ocean tides, which impairs ecosystem services and often promotes invasive species. Numerous restoration projects now focus on removing impoundments. Leaf litter decomposition is a central process in salt marsh carbon and nutrient cycles, and this study investigated the extent to which marsh restoration alters litter decomposition rates. We considered three environmental factors that can potentially change during restoration: salinity, tidal regime, and dominant plant species. A one-month field experiment (Cape Cod, MA) measured decay of litter bags in impounded, restored, and natural marshes under ambient conditions. A two-week lab experiment measured litter decay in controlled incubations under experimental treatments for salinity (1ppt and 30 ppt), tidal regime (inundated and 12 hr wet-dry cycles), and plant species (native Spartina alterniflora and invasive Phragmites australis). S. alterniflora decomposed faster in situ than P. australis (14±1.0% mass loss versus 0.74±0.69%). Corroborating this difference in decomposition, S. alterniflora supported greater microbial respiration during lab incubation, measured as CO2 flux from leaf litter and biological oxygen demand of water containing leached organic matter (OM). However, nutrient analysis of plant tissue and leached OM show P. australis released more nitrogen than S. alterniflora. Low salinity treatments in both lab and field experiments decayed more rapidly than high salinity treatments, suggesting that salinity inhibited microbial activity. Manipulation of inundation regime did not affect decomposition. These findings suggest the reintroduction of tidal flow to an impounded salt marsh can have mixed effects; recolonization by the native cordgrass could supply labile OM to sediment and slow carbon sequestration, while an increase in salinity might inhibit decomposition and accelerate sequestration.

Acidity of Lakes and Impoundments in North-Central Minnesota

Science.gov (United States)

Elon S. Verry

1981-01-01

Measurements of lake and impoundment pH for several years, intensive sampling within years, and pH-calcium plots verify normal pH levels and do not show evidence of changes due to acid precipitation. These data in comparison with general lake data narrow the northern Lake States area in which rain or snow may cause lake acidification.

Geomorphological assessment of sites and impoundments for the long term containment of uranium mill tailings in the Alligator Rivers Region

International Nuclear Information System (INIS)

East, T.J.

1985-01-01

Current and future research into the geomorphological processes likely to affect the long term containment of uranium mill tailings in the Alligator Rivers Region is directed at three main areas: identification of geomorphic hazards at proposed impoundment sites; determination of erosion rates on impoundment slopes; and prediction of patterns of fluvial dispersal of released tailings. Each necessitates consideration of present and future geomorphic processes. Process rates during the next few thousand years might be predictable by extrapolation of contemporary and past (i.e. Holocene) climates, sea-levels and depositional environments, evidence for which is preserved in the sedimentary record. In current projects, the Late Quarternary stratigraphy of Magela Creek are examined to provide data for modelling of present and future sedimentological processes. Site stability evaluation entails recognition of present and future geomorphic hazards at impoundment sites, and includes fluvial and hillslope erosion, extreme flood events and mass movements. The life of a tailings impoundment is further determined by the intensity of erosional processes acting upon its slopes and their cover materials. A knowledge of present and future erosion rates will allow the optimisation of slope characteristics and materials in the impoundment design

Evaluation of factors related to increased zooplankton biomass and altered species composition following impoundment of a Newfoundland reservoir

International Nuclear Information System (INIS)

Campbell, C.E.; Knoechel, R.; Copeman, D.

1998-01-01

An 11-year study of the zooplankton community in Cat Arm Hydroelectric Reservoir in Newfoundland was conducted to assess long-term zooplankton community dynamics in a subarctic system. Zooplankton biomass and species compositions were monitored from 1983 to 1993. The monitoring program documented the trophic evolution of the Cat Arm system as it changed from a shallow lake with short water retention time to a deep reservoir with a much lower flushing rate. Zooplankton biomass increased approximately 19-fold in the oligotrophic hydroelectric reservoir following impoundment in 1984, relative to biomass in the preexisting lake. During the first three years of impoundment, there were no increases in either phytoplankton biomass or primary productivity. Natality of the dominant cladoceran (Daphnia catawba) did not increase. Summer water retention time increased from pre-impoundment levels of 4 days in 1983 to 338 days in 1993. The study showed that zooplankton biomass was greatly correlated with water retention time, and showed no major correlation with phytoplankton biomass, primary productivity, nutrient concentrations, pH, colour, or epilimnetic temperature. It was concluded that changes in the zooplankton community in the hydroelectric reservoir were a result of decreases in losses due to washout. 41 refs., 2 tabs., 6 figs

Effects of increased summer flooding on nitrogen dynamics in impounded mangroves

NARCIS (Netherlands)

Verhoeven, Jos T A; Laanbroek, Hendrikus J; Rains, Mark C; Whigham, Dennis F

2014-01-01

Mangroves are important for coastal protection, carbon sequestration and habitat provision for plants and animals in the tropics and subtropics. Mangroves are threatened by habitat destruction and sea level rise, but management activities such as impounding for mosquito control can also have

Effect of weir impoundments on methane dynamics in a river

Czech Academy of Sciences Publication Activity Database

Bednařík, A.; Blaser, M.; Matoušů, Anna; Hekera, P.; Rulík, M.

2017-01-01

Roč. 584, April (2017), s. 164-174 ISSN 0048-9697 R&D Projects: GA ČR(CZ) GA13-00243S Institutional support: RVO:60077344 Keywords : methane production * methane emission * methane ebullition * river impoundment * river sediment Subject RIV: DA - Hydrology ; Limnology OBOR OECD: Marine biology, freshwater biology, limnology Impact factor: 4.900, year: 2016

Reestablishment of woody plants on mine spoils and management of mine water impoundments: an overview of Forest Service research on the northern High Plain

Energy Technology Data Exchange (ETDEWEB)

Bjugstad, A J

1977-01-01

The function of the research unit at Rapid city, S. Dakota, is to provide guidelines for the reestablisment of shrubs and trees on land characteristic of the High Plains, and for the mitigation of possible detrimental effects of surface mining on ground water and surface water. One possible problem posed by surface mining concerns the formation of land drainage patterns that could result in post-mining formations of large salt playas. Surface mining could affect shallow ground water aquifers up to /sup 1///sub 4/ mile from the mine site. Research is being conducted on the reclamation of mine spoils and on the rehabilitation and management of impounded mine water.

Hypersalinity reduces the risk of cyanide toxicosis to insectivorous bats interacting with wastewater impoundments at gold mines.

Science.gov (United States)

Griffiths, Stephen R; Donato, David B; Lumsden, Linda F; Coulson, Graeme

2014-01-01

Wildlife and livestock that ingest bioavailable cyanide compounds in gold mining tailings dams are known to experience cyanide toxicosis. Elevated levels of salinity in open impoundments have been shown to prevent wildlife cyanide toxicosis by reducing drinking and foraging. This finding appears to be consistent for diurnal wildlife interacting with open impoundments, however the risks to nocturnal wildlife of cyanide exposure are unknown. We investigated the activity of insectivorous bats in the airspace above both fresh (potable to wildlife) and saline water bodies at two gold mines in the goldfields of Western Australian. During this study, cyanide-bearing solutions stored in open impoundments at both mine sites were hypersaline (range=57,000-295,000 mg/L total dissolved solids (TDS)), well above known physiological tolerance of any terrestrial vertebrate. Bats used the airspace above each water body monitored, but were more active at fresh than saline water bodies. In addition, considerably more terminal echolocation buzz calls were recorded in the airspace above fresh than saline water bodies at both mine sites. However, it was not possible to determine whether these buzz calls corresponded to foraging or drinking bouts. No drinking bouts were observed in 33 h of thermal video footage recorded at one hypersaline tailings dam, suggesting that this water is not used for drinking. There is no information on salinity tolerances of bats, but it could be assumed that bats would not tolerate salinity in drinking water at concentrations greater than those documented as toxic for saline-adapted terrestrial wildlife. Therefore, when managing wastewater impoundments at gold mines to avoid wildlife mortalities, adopting a precautionary principle, bats are unlikely to drink solutions at salinity levels ≥50,000 mg/L TDS. © 2013 Published by Elsevier Inc.

Organochlorine pesticide levels in Clarias gariepinus from polluted freshwater impoundments in South Africa and associated human health risks

CSIR Research Space (South Africa)

Barnhoorn, IEJ

2014-02-01

Full Text Available There are increasing concerns regarding the safe human consumption of fish from polluted, freshwater impoundments. The aim of this study was to analyse the muscle tissue of the sharptooth catfish Clarias gariepinus for selected organo-chlorine...

Reestablishing the Dominance of Biogeochemical Pathways for Reducing Downstream Nutrient Losses from Aged Impounded Features

Science.gov (United States)

Shukla, S.; Shukla, A.

2017-12-01

Water and phosphorus (P) dynamics and loss pathways at two stormwater impoundments (SIs) were analyzed using measured fluxes between 2008 and 2011. These SIs are a decade old. Analyses of water and P budgets along with the discernment of various P pools and characterization of the intermediary processes revealed that soil adsorption and plant uptake are secondary to volume reduction apropos of P treatment. At one site, extreme wet conditions in a year combined with soil P saturation resulted in it being a P source rather than a sink. The impoundment (SI-1) discharged 12% more P than incoming due to soil P desorption, a consequence of dilution of incoming stormwater with large water input from an extreme tropical rain event. The second impoundment (SI-2) was a consistent sink of P; 55% and 95% of the incoming total P was retained in the two years, mainly as a result of 49% and 84% volume retention, respectively. Analysis of plant available aluminum, iron, and phosphorus showed the surface soil to be P saturated and at risk of releasing P to a limit of environmental concern. These results when seen in light of more frequent extreme precipitation events under the changed climate scenario call for alternatives to revive the role of biogeochemical processes in P treatment because volume reduction may not always be the viable option, especially for wet conditions. Aboveground biomass harvesting and removal was evaluated to transform the SIs from a frequent P source to sink and maintain the long-term sink functions of the SIs. Use of harvested biomass as a source of nutrients (N and P) and carbon to agricultural soil can result in beneficial use of biomass and offset the cost of harvesting. Other avenues such as altering the hydrology of the SIs by compartmentalizing the system and increasing the storage were also explored for short-term benefits. Results provided a combination of hydraulic and biochemical options for achieving long-term water and nutrient retentions in

A model for evaluating effects of climate, water availability, and water management on wetland impoundments--a case study on Bowdoin, Long Lake, and Sand Lake National Wildlife Refuges

Science.gov (United States)

Tangen, Brian A.; Gleason, Robert A.; Stamm, John F.

2013-01-01

Many wetland impoundments managed by the U.S. Fish and Wildlife Service (USFWS) National Wildlife Refuge System throughout the northern Great Plains rely on rivers as a primary water source. A large number of these impoundments currently are being stressed from changes in water supplies and quality, and these problems are forecast to worsen because of projected changes to climate and land use. For example, many managed wetlands in arid regions have become degraded owing to the long-term accumulation of salts and increased salinity associated with evapotranspiration. A primary goal of the USFWS is to provide aquatic habitats for a diversity of waterbirds; thus, wetland managers would benefit from a tool that facilitates evaluation of wetland habitat quality in response to current and anticipated impacts of altered hydrology and salt balances caused by factors such as climate change, water availability, and management actions. A spreadsheet model that simulates the overall water and salinity balance (WSB model) of managed wetland impoundments is presented. The WSB model depicts various habitat metrics, such as water depth, salinity, and surface areas (inundated, dry), which can be used to evaluate alternative management actions under various water-availability and climate scenarios. The WSB model uses widely available spreadsheet software, is relatively simple to use, relies on widely available inputs, and is readily adaptable to specific locations. The WSB model was validated using data from three National Wildlife Refuges with direct and indirect connections to water resources associated with rivers, and common data limitations are highlighted. The WSB model also was used to conduct simulations based on hypothetical climate and management scenarios to demonstrate the utility of the model for evaluating alternative management strategies and climate futures. The WSB model worked well across a range of National Wildlife Refuges and could be a valuable tool for USFWS

[Influence of 175-m-impoundment in Three Gorges Reservoir area on the food web energy sources of main commercial fishes in backwater area of xiaojiang River].

Science.gov (United States)

Li, Bin; Wang, Zhi-Jian; Yue, Xing-Jian; Wang, Yong-Ming; Jin, Li; Zhang, Yao-Guang

2013-06-01

The impoundment in the Three Gorges Reservoir Area (TGRA) was first reached 175 m in 2010. To approach the influence of this impoundment on the food web energy sources of fishes in the tributaries of TRGA, an analysis was made on the food web energy sources of seven economically important fishes (Carassius auratus, Cyprinus carpio, Silurus asotus, Culter mongolicus mongolicus, Mystus macropterus, Pelteobagrus vachelli, and Pelteobagrus nitidus) in the backwater area of Xiaojiang River by using stable isotope method in combining with IsoSource Model. The results showed that before this impoundment (July 2010), microalgae were the main energy sources for the seven species. After this impoundment (December 2010), the contribution ratio of the microalgae decreased somewhat, while the relative contribution of terrestrial C4 plants had an obvious increase. Especially for crucian carp (C. auratus) and catfish (S. asotus), the contribution rate of the C4 plants reached 38-54% and 32-50%, respectively. After the impoundment, at least 30% of the energy resources of these two fishes were come from terrestrial C4 plants, suggesting that the impoundment in TGRA increased the contribution rate of exogenous terrestrial C4 plants as the energy sources of fishes.

Dose assessment of remedial action for uranium tailing impoundment of a nuclear factory

International Nuclear Information System (INIS)

Li Xutong; Ma Ruwei; Guo Zede

2000-01-01

A large uranium tailing impoundment in China will be closure and remedial action have been planned. The remedial action will include shaping and covering the dam and beach in order to prevent the impoundment from damage and restrict spread of tailing sands and emission of radon. The author presents the analysis and estimation of the exposure to workers for remedial action and to public after the remedial action. To estimate the exposure to workers, the pathway of inhalation of radon, tailing sands in suspension and external γ exposure were taken into consideration. The exposure scenario is considered as probably maximum exposure to the workers who work on the tailing pile without any protection measures, the dose is 6.0 mSv/a. Two situation for the exposure to public after remedial action were considered: normal and abnormal condition. For the normal condition, inhalation of radon emitted from impoundment is only the pathway to public for the exposure, and individual dose for critical group of public is 0.053 mSv/a, collective dose for population within 80 km is 1.0 man·Sv/a. For the abnormal conditions, four scenarios were considered, i.e. dwelling on tailing pile, farming on tailing pile, living in a house built by contaminated materials and some temporal activities on the pile. The scenarios of dwellings is living in a house on the pile and drinking contaminated water. The maximum individual dose is 27 mSv/a

Rehabilitation of uranium tailings impoundments

International Nuclear Information System (INIS)

Crawley, A.H.

1983-01-01

Under Australian environmental controls relating to the management of uranium tailings, it is no longer acceptable practice to search for a rehabilitation strategy at the end of production when the generation of tailings has ceased. The uranium projects currently in production and those being proposed are tightly regulated by the authorities. The waste management plans must consider site specific factors and must include selection of appropriate disposal sites and design for long term containment. The final encapsulation in engineered facilities must take into account the probable routes to the environment of the tailings. Rehabilitation shoud be undertaken by the mining and milling operators to standards approved by appropriate authorities. Appropriate administrative arrangements are required, by way of technical committees and financial bonds to ensure that agreed standards of rehabilitation may be achieved. Past and present experience with the rehabilitation of uranium tailings impoundments in Australia is discussed

Evaluation of behaviors of earth and rockfill dams during construction and initial impounding using instrumentation data and numerical modeling

Directory of Open Access Journals (Sweden)

Mohammad Rashidi

2017-08-01

Full Text Available In this study, the behavior of Gavoshan dam was evaluated during construction and the first impounding. A two-dimensional (2D numerical analysis was conducted based on a finite difference method on the largest cross-section of the dam using the results of instrument measurements and back analysis. These evaluations will be completed in the case that back analysis is carried out in order to control the degree of the accuracy and the level of confidence of the measured behavior since each of the measurements could be controlled by comparing it to the result obtained from the numerical model. Following that, by comparing the results of the numerical analysis with the measured values, it is indicated that there is a proper consistency between these two values. Moreover, it was observed that the dam performance was suitable regarding the induced pore water pressure, the pore water pressure ratio ru, settlement, induced stresses, arching degree, and hydraulic fracturing probability during the construction and initial impounding periods. The results demonstrated that the maximum settlement of the core was 238 cm at the end of construction. In the following 6 years after construction (initial impounding and exploitation period, the accumulative settlement of the dam was 270 cm. It is clear that 88% of the total settlement of the dam took place during dam construction. The reason is that the clay core was smashed in the wet side, i.e. the optimum moisture content. Whereas the average curving ratio was 0.64 during dam construction; at the end of the initial impounding, the maximum amount of curving ratio in the upstream was 0.81, and the minimum (critical amount in the downstream was 0.52. It was also concluded that this dam is safe in comparison with the behaviors of other similar dams in the world.

Characterization of transient groundwater flow through a high arch dam foundation during reservoir impounding

Directory of Open Access Journals (Sweden)

Yifeng Chen

2016-08-01

Full Text Available Even though a large number of large-scale arch dams with height larger than 200 m have been built in the world, the transient groundwater flow behaviors and the seepage control effects in the dam foundations under difficult geological conditions are rarely reported. This paper presents a case study on the transient groundwater flow behaviors in the rock foundation of Jinping I double-curvature arch dam, the world's highest dam of this type to date that has been completed. Taking into account the geological settings at the site, an inverse modeling technique utilizing the time series measurements of both hydraulic head and discharge was adopted to back-calculate the permeability of the foundation rocks, which effectively improves the uniqueness and reliability of the inverse modeling results. The transient seepage flow in the dam foundation during the reservoir impounding was then modeled with a parabolic variational inequality (PVI method. The distribution of pore water pressure, the amount of leakage, and the performance of the seepage control system in the dam foundation during the entire impounding process were finally illustrated with the numerical results.

Geometrical and hydrogeological impact on the behaviour of deep-seated rock slides during reservoir impoundment

Science.gov (United States)

Lechner, Heidrun; Zangerl, Christian

2015-04-01

Given that there are still uncertainties regarding the deformation and failure mechanisms of deep-seated rock slides this study concentrates on key factors that influence the behaviour of rock slides in the surrounding of reservoirs. The focus is placed on the slope geometry, hydrogeology and kinematics. Based on numerous generic rock slide models the impacts of the (i) rock slide geometry, (ii) reservoir impoundment and level fluctuations, (iii) seepage and buoyancy forces and (iv) hydraulic conductivity of the rock slide mass and the basal shear zone are examined using limit equilibrium approaches. The geometry of many deep-seated rock slides in metamorphic rocks is often influenced by geological structures, e.g. fault zones, joints, foliation, bedding planes and others. With downslope displacement the rock slide undergoes a change in shape. Several observed rock slides in an advanced stage show a convex, bulge-like topography at the foot of the slope and a concave topography in the middle to upper part. Especially, the situation of the slope toe plays an important role for stability. A potentially critical situation can result from a partially submerged flat slope toe because the uplift due to water pressure destabilizes the rock slide. Furthermore, it is essential if the basal shear zone daylights at the foot of the slope or encounters alluvial or glacial deposits at the bottom of the valley, the latter having a buttressing effect. In this study generic rock slide models with a shear zone outcropping at the slope toe are established and systematically analysed using limit equilibrium calculations. Two different kinematic types are modelled: (i) a translational or planar and (ii) a rotational movement behaviour. Questions concerning the impact of buoyancy and pore pressure forces that develop during first time impoundment are of key interest. Given that an adverse effect on the rock slide stability is expected due to reservoir impoundment the extent of

Geomorphological assessment of sites and impoundments for the long term containment of uranium mill tailings in the Alligator Rivers Region

International Nuclear Information System (INIS)

East, T.J.

1986-01-01

This paper presents a program of current and future research into those geomorphological processes likely to affect the long term containment of uranium mill tailings in the Alligator Rivers Region of the Northern Territory. Research is directed at three main areas: identification of geomorphic hazards at proposed impoundment sites; determination of erosion rates on impoundment slopes; and prediction of patterns of fluvial dispersal of released tailings. Each necessitates consideration of present and future geomorphic processes

Conversion of a tailing impoundment to a freshwater reservoir, the Eagle Park Reservoir project, Climax Mine, Colorado

Energy Technology Data Exchange (ETDEWEB)

Romig, B.R.; Cupp, J.L.; Ford, R.C.

1999-07-01

The Climax Molybdenum Mine, located near Leadville, Colorado, is the site of a lengthy mining history spanning more than 80 years. In the 1960's, extraction of molybdenum from oxide ore located adjacent to the massive molybdenite sulfide deposit resulted in the construction of an earthen core dam to impound fine-grained oxide tailing in the Eagle River Valley. Through recognized value of water storage and reclamation opportunities, a tailing removal project was initiated in 1993 to convert the impoundment facilities to a post-mining beneficial land use of developed water resources. An evaluation of the effect residual materials and lake dynamics would have on in-stream water quality was performed. Eagle Park Reservoir stands as a model for future reclamation efforts that involve water delivery to highly sensitive receiving waters. This paper provides a case study on project development, the evolution of water quality assessment, and the regulatory framework that contributed to this project's success.

contaminant migration in a sand aquifer near an inactive uranium tailings impoundment, Elliot Lake, Ontario

International Nuclear Information System (INIS)

Morin, K.A.; Cherry, J.A.

1982-01-01

An investigation of the movement of contaminated groundwater from inactive uranium tailings through a sand aquifer is being conducted at the Nordic Main tailings impoundment near Elliot Lake, Ontario. During 1979 and 1980, multilevel bundle-type piezometers were installed at several locations around the edge of the tailings impoundment. Chemical analysis of water samples from the bundle piezometers indicate that a major contaminant plume extends outward through a sand aquifer from the southeastern part of the Nordic Main impoundment dam. In the vincinity of the contaminant plume, the sand aquifer varies in thickness from about 9 to 15 m. The plume has two distinct segments, referred to as the inner core and the outer zone. The inner core, which has a pH of 4.3-5.0 and extends about 15 m from the foot of the tailings dam, contains several grams per litre of iron and sulfate, and tens of pCi/L of 226 Ra and 210 Pb. Water levels in piezometers within the inner core show that groundwater is moving horizontally, away from the tailings impoundment, with a velocity of up to several hundred metres per year. The outer zone, which extends a few hundred metres downgradient from the dam, is characterized by hundreds to thousands of milligrams per litre of iron and sulfate, less than 15pCi/L of 226 Ra, and a pH greater than 5.7. Comparison of 1979 and 1980 data shows that the front of the inner core is advancing a few metres per year, which is less than a few percent of the groundwater velocity. This retardation of movement of the inner core is caused by neutralization of the acidic water as a result of dissolution of calcium carbonate in the sand. With the rise in pH, precipitation of iron carbonate and possibly some iron hydroxide occurs and the contaminants of main concern such as 226 Ra, 210 Pb, and uranium are removed from solution by adsorption or coprecipitation

Arsenic mobility from anthropogenic impoundment sediments - Consequences of contamination to biota, water and sediments, Posa, Eastern Slovakia

Energy Technology Data Exchange (ETDEWEB)

Hiller, E.; Jurkovic, L.; Kordik, J.; Slaninka, I.; Jankular, M.; Majzlan, J.; Gottlicher, J.; Steininger, R. [Geological Survey of Slovak Republic, Bratislava (Slovakia). Dept. of Environmental Geochemistry

2009-11-15

An impoundment located near the village of Posa, Slovakia, is a significant source of contamination with As originating from the deposited coal fly-ash. Waters penetrating the impoundment are enriched in As and other potentially toxic elements. As a consequence of the contamination, the Kyjov Brook and the Ondava River have been extensively polluted. The mobility and solid-state partitioning of As in the impoundment material and stream sediments were investigated using column leaching and batch extraction tests, and a five-step sequential extraction procedure. Moreover, to investigate the bioavailability of As, two native plant species (Typha latifolia, or cattail, and Phragmites australis, or common reed) growing at the site were collected and analyzed. The As concentrations in representative sediment and water samples ranged from 36.3 to 3210 mg/kg and from 4.05 to 613 {mu} g/L, respectively, both being many times above the background levels. Although a part of As was present in a readily soluble form (6.6%), the majority of As was mainly associated with Fe and Mn oxides (37%) and residual phases (51%). Combined results of the column leaching, batch extraction, and sequential extraction tests, as well as mineralogical analysis, indicated that As mobilisation potential from the sediments is likely controlled by Fe, Al and Mn oxides, and by pH. There was no influence of various anions (PO{sub 4}{sup 3-}, SO{sub 4}{sup 2-}, NO{sup 3-}, Cl{sup -} and HCO{sub 3}{sup -}) on As mobility when present in aqueous solution at concentrations analogous to those in the water of the Kyjov Brook. Plants growing in the impoundment had As concentrations 10-100 times greater than did the same plants growing in a relatively non-polluted area.

Low-level radioactive waste disposal in the USA - Use of mill tailings impoundments as a new policy option

International Nuclear Information System (INIS)

Farrell, C.W.

2006-01-01

Disposal of low-level radioactive waste (LLW) in the United States is facing severe and immediate capacity limitations. Seemingly intractable regulatory and jurisdictional conflicts make establishment of new LLW disposal sites effectively impossible. Uranium mill tailings impoundments constructed at conventional uranium open-cast and underground mines could offer approximately 40 to 80+ million tons of disposal capacity for low activity radioactive waste. Such impoundments would provide an enhanced, high level of environmental and health and safety protection for the direct disposal of depleted uranium, special nuclear material, technologically-enhanced, naturally-occurring radioactive material (TENORM) and mixed waste. Many waste streams, such as TENORM and decommissioning rubble, will be high-volume, low activity materials and ideally suited for disposal in such structures. Materials in a given decay chain with a total activity from all radionuclides present of ∼820 Bq/g (2.22 x 10 -08 Ci/g) with no single radionuclide present in an activity greater than ∼104 Bq/g (2,800 pCi/g) should be acceptable for disposal. Materials of this type could be accepted without any site-specific dose modelling, so long as the total activity of the tailings impoundment not exceed its design capacity (generally 82 x 10 07 Bq/metric tonne) (0.020 Ci/short ton) and the cover design requirements to limit radon releases are satisfied. This paper provides background on US LLW disposal regulations, examines LLW disposal options under active consideration by the US Environmental Protection Agency and Department of Energy, develops generic waste acceptance criteria and identifies policy needs for federal and state governments to facilitate use of uranium mill tailings impoundments for LLW disposal. (author)

Change characteristics of DSi and nutrition structure at the Yangtze River Estuary after Three Gorges Project impounding and their ecological effect

Directory of Open Access Journals (Sweden)

Li Lei

2017-06-01

Full Text Available The variation law of dissolved silica (DSi, dissolved inorganic nitrogen (DIN, dissolved inorganic phosphorus (DIP and nutrition structure after the Three Gorges Project (TGP impounding as well as their ecological effect were analyzed according to monitoring survey of the Yangtze River Estuary in spring (May and summer (August from 2004-2009. The results showed that after impounding, DSi and DIN concentration decreased and increased, respectively. During the study period, DSi decreased by about 63%, while DIN almost tripled. DIP concentration fluctuated slightly. With respect to nutrition structure, N:P increased, whereas Si:P and Si:N declined. According to chemometry standard of nutrient limits, nutrition structure tended to be imbalanced and the limiting factor of phytoplankton growth (P was studied. Changes of nutrition structure have largely decreased diatom and caused different composition of dominant phytoplankton species. This may change ecosystem structure of the Yangtze River Estuary.

Limnology and fisheries of three recently impounded reservoirs in Sri Lanka

International Nuclear Information System (INIS)

Silva, K.H.G.M De

1990-01-01

The hydroelectric reservoirs of Kotmale, Victoria, and Randenigala were impounded in 1985, 1984, and 1986, respectively, by damming the Mahaweli River. The surface area, maximum depth, and mean depth of the three reservoirs are 6.3 km 2 , 78 m, 27.6 m; 23.7 km 2 , 102 m, 30.8 m; and 23.5 km 2 , 90 m, 36.6 m respectively, at their full supply levels of 703, 438, and 232 m above mean sea level. Important physicochemical factors and phytoplankton were studied by sampling of subsurface waters every two weeks in 12 randomly chosen stations in Randenigala and Victoria, and in 10 stations in Kotmale over 24 months. Mean water temperature, pH, conductivity, and the total alkalinity during the study period were 25.6 degree C, 6.6, 50.7 μsieverts, and 0.31 millimoles/l in Kotmale, 26.9 degree C, 7.1, 77.4 μsieverts, and 0.62 millimoles/l in Victoria, and 28.3 degree C, 7.4, 90.0 μsieverts, and 0.79 millimoles/l in Randenigala. The gill-net catches of Kotmale and Victoria are ca 38 and 70 kg/hectare/y, respectively. Randenigala has a fishery potential of ca 70 kg/hectare/y. Tilapia formed ca 68%, 59%, and 69% of the catches of Kotmale, Victoria, and Randenigala, respectively. The catch at Kotmale was mainly Java tilapia and Nile tilapia, whereas at the other two reservoirs it was mainly Java tilapia. Indigenous species constituted only ca 10% of the catch. 16 refs., 2 figs., 4 tabs

Impacts of Freshwater Impoundment in the West Loch of Pearl Harbor

Science.gov (United States)

1993-05-01

absence of applicable non-point standards, the "Yellow Book" criteria for freshwater aquatic life or domestic water supply could be applied to evaluate the...Waimalu, Waipahu, Wahiawa, and Ewa water use districts and contains the largest groundwater body on Oahu, supplying more than 50 percent of the island’s...irrigation; desalt existing brackish water supplies, and; 3 create a freshwater impoundment in West Loch. 6I I I The Board of Water Supply (BWS) and

Eutrophication levels of some South African impoundments. IV. Vaal Dam

CSIR Research Space (South Africa)

Steyn, DJ

1976-04-01

Full Text Available inere;iae(l the \\G P In? between 7,1- and I 1,2 mg/r? lbr t?verv nile pet? t?t?ttt v/v) added_Nitrogen and phosphorus wert? the important algal growth?limiting ntltrients in the impoundment. Plant nntt-ients adsorbed onto clay particles could ht... stream_source_info Steyn2_1976.pdf.txt stream_content_type text/plain stream_size 20870 Content-Encoding ISO-8859-1 stream_name Steyn2_1976.pdf.txt Content-Type text/plain; charset=ISO-8859-1 Za~3n Abstract The Vital...

Relationships among catch, angler catisfaction, and fish assemblage characteristics of an urban small impoundment fishery

Science.gov (United States)

Ivasauskas, Tomas J.; Xiong, Wilson N.; Engman, Augustin C.; Fischer, Jesse R.; Kwak, Thomas J.; Rundle, Kirk R.

2017-01-01

Urban fisheries provide unique angling opportunities for people from traditionally underrepresented demographics. Lake Raleigh is a 38-ha impoundment located on the North Carolina State University campus in Raleigh. Like many urban fisheries, little is known about angler use and satisfaction or how angling catch rate is related to fish availability in Lake Raleigh. We characterized the recreational fishery and fish assemblage with concurrent creel and boat electrofishing surveys over the course of one year. In total, 245 anglers were interviewed on 68 survey days. On average, anglers spent 1.7 h fishing per trip and caught 0.385 fish h –1. A large proportion of anglers (43.9%) targeted multiple species, whereas 36.5% targeted largemouth bass (Micropterus salmoides), 10.0% targeted panfish (i.e., sunfishes [Lepomis spp.] and crappies [Pomoxis spp.]), and 9.6% targeted catfish (Ameiurus spp. and Ictalurus spp.). Most anglers (69.4%) were satisfied with their experience, and overall satisfaction was unrelated to catch rate. Pulsed-DC boat electrofishing was conducted on 25 dates, and 617 fish were sampled. Angler catch rate was unrelated to electrofishing catch rate, implying that anglers' catch rate was independent of fish density or availability. Our results demonstrate that even minimally managed urban fisheries can provide high angler satisfaction, with limited dedication of management resources. Relationships Among Catch, Angler Satisfaction, and Fish Assemblage Characteristics of an Urban Small Impoundment Fishery (PDF Download Available). Available from: https://www.researchgate.net/publication/316636550_Relationships_Among_Catch_Angler_Satisfaction_and_Fish_Assemblage_Characteristics_of_an_Urban_Small_Impoundment_Fishery [accessed Aug 11, 2017].

A long-term comparison of carbon sequestration rates in impounded and naturally tidal freshwater marshes along the lower Waccamaw River, South Carolina

Science.gov (United States)

Drexler, Judith Z.; Krauss, Ken W.; Sasser, M. Craig; Fuller, Christopher C.; Swarzenski, Christopher M.; Powell, Amber; Swanson, Kathleen M.; Orlando, James L.

2013-01-01

Carbon storage was compared between impounded and naturally tidal freshwater marshes along the Lower Waccamaw River in South Carolina, USA. Soil cores were collected in (1) naturally tidal, (2) moist soil (impounded, seasonally drained since ~1970), and (3) deeply flooded “treatments” (impounded, flooded to ~90 cm since ~2002). Cores were analyzed for % organic carbon, % total carbon, bulk density, and 210Pb and 137Cs for dating purposes. Carbon sequestration rates ranged from 25 to 200 g C m−2 yr−1 (moist soil), 80–435 g C m−2 yr−1 (naturally tidal), and 100–250 g C m−2 yr−1 (deeply flooded). The moist soil and naturally tidal treatments were compared over a period of 40 years. The naturally tidal treatment had significantly higher carbon storage (mean = 219 g C m−2 yr−1 vs. mean = 91 g C m−2 yr−1) and four times the vertical accretion rate (mean = 0.84 cm yr−1 vs. mean = 0.21 cm yr−1) of the moist soil treatment. The results strongly suggest that the long drainage period in moist soil management limits carbon storage over time. Managers across the National Wildlife Refuge system have an opportunity to increase carbon storage by minimizing drainage in impoundments as much as practicable.

Hydrologic considerations for rock RIPRAP protection of uranium tailings impoundments

International Nuclear Information System (INIS)

Walters, W.H.; Skaggs, R.L.

1984-02-01

Pacific Northwest Laboratory is conducting an in-depth study of the application of rock riprap for the long-term protection of uranium tailings impoundments. Decommissioned tailings sites at Grand Junction and Slickrock, Colorado were selected to review the application of riprap design methods and evaluate variable sensitivity and data requirements. Preliminary results from the Grand Junction case study indicate that the use of a safety factor in sizing the rock riprap may provide an overly conservative design that may not be justified. Some safety factor, usually a value of 1.5 to 2.0 is normally used in riprap design to allow for the uncertainties in the hydraulic calculations. The computation of the hydraulic designs variables using the probable maximum flood (PMF) event introduces conservatism into the design and the added safety factor may not be warranted. This paper presents some preliminary results from the Grand Junction site concerning the implications of using a safety factor for riprap design. 9 references, 2 figures, 2 tables

Geochemical characterisation of seepage and drainage water quality from two sulphide mine tailings impoundments: Acid mine drainage versus neutral mine drainage

Science.gov (United States)

Heikkinen, P.M.; Raisanen, M.L.; Johnson, R.H.

2009-01-01

Seepage water and drainage water geochemistry (pH, EC, O2, redox, alkalinity, dissolved cations and trace metals, major anions, total element concentrations) were studied at two active sulphide mine tailings impoundments in Finland (the Hitura Ni mine and Luikonlahti Cu mine/talc processing plant). The data were used to assess the factors influencing tailings seepage quality and to identify constraints for water treatment. Changes in seepage water quality after equilibration with atmospheric conditions were evaluated based on geochemical modelling. At Luikonlahti, annual and seasonal changes were also studied. Seepage quality was largely influenced by the tailings mineralogy, and the serpentine-rich, low sulphide Hitura tailings produced neutral mine drainage with high Ni. In contrast, drainage from the high sulphide, multi-metal tailings of Luikonlahti represented typical acid mine drainage with elevated contents of Zn, Ni, Cu, and Co. Other factors affecting the seepage quality included weathering of the tailings along the seepage flow path, process water input, local hydrological settings, and structural changes in the tailings impoundment. Geochemical modelling showed that pH increased and some heavy metals were adsorbed to Fe precipitates after net alkaline waters equilibrated with the atmosphere. In the net acidic waters, pH decreased and no adsorption occurred. A combination of aerobic and anaerobic treatments is proposed for Hitura seepages to decrease the sulphate and metal loading. For Luikonlahti, prolonged monitoring of the seepage quality is suggested instead of treatment, since the water quality is still adjusting to recent modifications to the tailings impoundment.

The role of cassiterite controlling arsenic mobility in an abandoned stanniferous tailings impoundment at Llallagua, Bolivia.

Science.gov (United States)

Romero, Francisco Martín; Canet, Carles; Alfonso, Pura; Zambrana, Rubén N; Soto, Nayelli

2014-05-15

The surface water contamination by potentially toxic elements (PTE) leached from mine tailings is a major environmental concern. However, the formation of insoluble solid phases can control the mobility of PTE, with subsequent decrease of the risk that tailings suppose to the environment. We characterized the tailings from a tin inactive mine in Llallagua, Bolivia in order to assess the risk for surface water quality. These tailings contain high concentrations of PTE, with up to 94,344 mg/kg Fe, 9,135 mg/kg Sn, 4,606 mg/kg As, 1,362 mg/kg Cu, 1,220 mg/kg Zn, 955 mg/kg Pb and 151 mg/kg Cd. Oxidation of sulfide minerals in these tailings generates acid leachates (pH=2.5-3.5), rich in SO4(2-) and dissolved PTE, thereby releasing contaminants to the surface waters. Nevertheless, the concentrations of dissolved Sn, As and Pb in acid leachates are low (Sntailing deposits; it should be the main solid phase controlling Sn and As mobility in the impoundment. Additionally, jarosite and plumbojarosite, identified among the secondary minerals, could also play an important role controlling the mobility of As and Pb. Taking into account (a) the low solubility constants of cassiterite (Ksp=10(-64.2)), jarosite (Ksp=10(-11)) and plumbojarosite (Ksp=10(-28.66)), and (b) the stability of these minerals under acidic conditions, we can conclude that they control the long-term fate of Sn, As and Pb in the studied tailings. Copyright © 2014 Elsevier B.V. All rights reserved.

Microcrustaceans (Branchipoda and Copepoda) of Wetland Impoundments on the Savannah River Site, Aiken, South Carolina

Energy Technology Data Exchange (ETDEWEB)

DeBiase, Adrienne E; Taylor, Barbara E

2005-09-21

The United States Department of Energy’s Savannah River Site (SRS) in Aiken, Allendale, and Barnwell Counties, South Carolina, contains an abundance of freshwater wetlands and impoundments. Four large impoundments, as well as several small, abandoned farm and mill ponds, and about 400 Carolina bays and other small, isolated depression wetland ponds are located within the 893 km2 area of the SRS. Crustaceans of the orders Branchiopoda and Copepoda are nearly ubiquitous in these water bodies. Although small in size, these organisms are often very abundant. They consequently play an important trophic role in freshwater food webs supporting fish, larval salamanders, larval insects, and numerous other animals, aquatic and terrestrial. This report provides an introduction to the free-living microcrustaceans of lentic water bodies on the SRS and a comprehensive list of species known to occur there. Occurrence patterns are summarized from three extensive survey studies, supplemented with other published and unpublished records. In lieu of a key, we provide a guide to taxonomic resources and notes on undescribed species. Taxa covered include the orders Cladocera, Anostraca, Laevicaudata, and Spinicaudata of the Subclass Branchiopoda and the Superorders Calanoida and Cyclopoida of Subclass Copepoda. Microcrustaceans of the Superorder Harpacticoida of the Subclass Copepoda and Subclass Ostracoda are also often present in lentic water bodies. They are excluded from this report because they have not received much study at the species level on the SRS.

[Effects of Three Gorges Reservoir impoundment on the wetland ecosystem service value of Dongting Lake, South-central China].

Science.gov (United States)

Li, Jing-Bao; Dai, Yong; Yin, Ri-Xin; Yang, Yan; Li, Yu-dan; Wang, Ke-ying

2013-03-01

Based on the field investigation and measurement, and by using the monetary method, this paper estimated the wetland ecosystem service value of Dongting Lake before and after the impoundment of Three Gorges Reservoir (in 1996 and 2010, respectively). After the impoundment, the total ecosystem service value increased from 156.69x10(8) yuan in 1996 to 177.11x10(8) yuan in 2010. The main services value in 1996 was in the order of flood storage and regulation > water storage and supply > air regulation > scientific research and education, while that in 2010 was leisure tourism > shipping transportation > air regulation > water storage and supply. In the total service value of the wetland ecosystem, the direct value associated with water decreased from 110. 85x10(8) in 1996 to 27.47x10(8) in 2010, with a decrement of 75.2%. Though the proportion of the direct value in the production and supply of material products had somewhat increase, the indirect value in ecological environment regulation and maintenance and in culture and society still maintained at about 80% of the total value. In addition to climate factors, the impoundment of Three Gorges Reservoir and the reduction of water and sediment from Yangtze River to the Lake were the crucial reasons leading to the changes of the wetland ecosystem service value of Dongting Lake.

Modulation of Extreme Flood Levels by Impoundment Significantly Offset by Floodplain Loss Downstream of the Three Gorges Dam

Science.gov (United States)

Mei, Xuefei; Dai, Zhijun; Darby, Stephen E.; Gao, Shu; Wang, Jie; Jiang, Weiguo

2018-04-01

River flooding—the world's most significant natural hazard—is likely to increase under anthropogenic climate change. Most large rivers have been regulated by damming, but the extent to which these impoundments can mitigate extreme flooding remains uncertain. Here the catastrophic 2016 flood on the Changjiang River is first analyzed to assess the effects of both the Changjiang's reservoir cascade and the Three Gorges Dam (TGD), the world's largest hydraulic engineering project on downstream flood discharge and water levels. We show that the Changjiang's reservoir cascade impounded over 30.0 × 103 m3/s of flow at the peak of the flood on 25 July 2016, preventing the occurrence of what would otherwise have been the second largest flood ever recorded in the reach downstream of the TGD. Half of this flood water storage was retained by the TGD alone, meaning that impoundment by the TGD reduced peak water levels at the Datong hydrometric station (on 25 July) by 1.47 m, compared to pre-TGD conditions. However, downstream morphological changes, in particular, extensive erosion of the natural floodplain, offset this reduction in water level by 0.22 m, so that the full beneficial impact of floodwater retention by the TGD was not fully realized. Our results highlight how morphological adjustments downstream of large dams may inhibit their full potential to mitigate extreme flood risk.

Mercury concentrations of fish in Southern Indian Lake and Issett Lake, Manitoba 1975-88: The effect of lake impoundment and Churchill River diversion

International Nuclear Information System (INIS)

Strange, N.E.; Bodaly, R.A.; Fudge, R.J.P.

1991-01-01

Southern Indian and Issett Lakes in northern Manitoba were flooded in 1976 as part of Manitoba Hydro's Churchill River diversion project. Fish were collected from 1975 to 1988 from five regional sites on the lakes to examine the effects of impoundment and river diversion on muscle mercury concentrations. Raw data for individual fish caught in 1987 and 1988 are presented, along with means and analyses calculated over the entire 1975-1988 study period. Mercury concentrations in whitefish, pike, and walleye increased significantly after impoundment. Whitefish mercury levels peaked in 1978 and have since declined to near pre-flooding levels. Northern pike and walleye mercury levels were much higher than for whitefish. Pike mercury concentrations showed no indication of declining after 12 years of impoundment, but walleye mercury levels at 2 of the 5 Southern Indian Lake sites declined from maximum recorded levels. Significant variability in fish mercury concentrations was noted both from year to year and among the sites. It is suggested that site-to-site variations are due to varying conditions in the reservoir which stimulate mercury methylation. Since there appears to be an ongoing long-term source of mercury and organic material from the eroding shorelines, pike and walleye mercury concentrations are expected to remain high for many years. 25 refs., 7 figs., 20 tabs

Cyanobacteria and cyanotoxins are present in drinking water impoundments and groundwater wells in desert environments.

Science.gov (United States)

Chatziefthimiou, Aspassia D; Metcalf, James S; Glover, W Broc; Banack, Sandra A; Dargham, Soha R; Richer, Renee A

2016-05-01

Desert environments and drylands experience a drastic scarcity of water resources. To alleviate dependence on freshwater for drinking water needs, countries have invested in infrastructure development of desalination plants. Collectively, the countries of the Arabian Gulf produce 45% of the world's desalinated water, which is stored in dams, mega-reservoirs and secondary house water tanks to secure drinking water beyond daily needs. Improper storage practices of drinking water in impoundments concomitant with increased temperatures and light penetration may promote the growth of cyanobacteria and accumulation of cyanotoxins. To shed light on this previously unexplored research area in desert environments, we examined drinking and irrigation water of urban and rural environments to determine whether cyanobacteria and cyanotoxins are present, and what are the storage and transportation practices as well as the environmental parameters that best predict their presence. Cyanobacteria were present in 80% of the urban and 33% of the rural water impoundments. Neurotoxins BMAA, DAB and anatoxin-a(S) were not detected in any of the water samples, although they have been found to accumulate in the desert soils, which suggests a bioaccumulation potential if they are leached into the aquifer. A toxic BMAA isomer, AEG, was found in 91.7% of rural but none of the urban water samples and correlated with water-truck transportation, light exposure and chloride ions. The hepatotoxic cyanotoxin microcystin-LR was present in the majority of all sampled impoundments, surpassing the WHO provisional guideline of 1 μg/l in 30% of the urban water tanks. Finally, we discuss possible management strategies to improve storage and transportation practices in order to minimize exposure to cyanobacteria and cyanotoxins, and actions to promote sustainable use of limited water resources. Copyright © 2016 Elsevier Ltd. All rights reserved.

Chlorophyll Detection and Mapping of Shallow Water Impoundments Using Image Spectrometry

International Nuclear Information System (INIS)

Artigas, F.; Pechmann, I.; Marti, A.; Yao, N.; Pechmann, I.

2008-01-01

There exists a common perception that chlorophyll a concentrations in tidal coastal waters are unsuitable to be captured by remote sensing techniques because of high water turbidity. In this study, we use band index measurements to separate active chlorophyll pigments from other constituents in the water. Published single- and multiband spectral indices are used to establish a relationship between algal chlorophyll concentration and reflectance data. We find an index which is suitable to map chlorophyll gradients in the impoundments, ditches, and associated waterways of the Hackensack Meadow lands (NJ, USA). The resulting images clearly depict the spatial distribution of plant pigments and their relationship with the biological conditions of the waters in the estuary. Since these biological conditions are often determined by land usage, the methods in this paper provide a simple tool to address water quality management issues in fragmented urban estuaries.

Effects of hydrologic variables on rock riprap design for uranium tailings impoundments

International Nuclear Information System (INIS)

Walters, W.H.; Skaggs, R.L.

1985-01-01

Pacific Northwest Laboratory is studying the mitigation of erosion of earthen radon suppression covers for uranium tailings impoundments. Because the covers will require erosion protection for upwards of 1000 years, rock riprap (armoring) has been proposed as the primary protection method. This study investigates the sensitivity of riprap design procedures to extreme flood events that can generate high flow velocities and shear stresses. The study uses two decommissioned tailings sites (Grand Junction and Slick Rock, Colorado) as case studies to evaluate the sensitivity of design rock size with respect to variables such as flood discharge, side slope, specific gravity, safety factor, and channel roughness. The results indicate that design rock size can vary significantly for different design procedures. Other significant results indicate that embankment side slopes of about 4H:1V are optimum for rock riprap and that the use of rock material with specific gravities less than about 2.50 may prove too costly

Synchronous response of sedimentary organic carbon accumulation on the inner shelf of the East China Sea to the water impoundment of Three Gorges and Gezhouba Dams

Science.gov (United States)

Lin, Jia; Zhu, Qing; Hong, Yuehui; Yuan, Lirong; Liu, Jinzhong; Xu, Xiaoming; Wang, Jianghai

2018-01-01

Coastal seas, located between continents and the open ocean, are an important active carbon pool. The sedimentary total organic carbon (TOC) in these areas is a mixture of terrestrial and marine sources, and can be a powerful proxy for tracing natural processes and human activities. In this study, one fine-grained sediment core (DH5-1) from the inner shelf of the East China Sea was systematically analyzed for TOC and black carbon (BC) contents and TOC stable carbon isotope ratios (δ13C). By combining these data with 210Pb dating, an improved carbon correction model and a two end-member mixing model, we reconstructed century-scale high-resolution sequences of corrected TOC, terrestrial TOC and marine TOC contents and identified two carbon depletion events in the DH5-1 record. The two events, shown as two minima in the TOC profiles, correspond temporally to 1985-1987 AD and 2003-2006 AD, which exactly matches the water impoundment of the Gezhouba Dam and Three Gorges Dam, respectively. In addition, the variations in TOC contents and δ13C values before, during or after the minima demonstrate a relationship between the depletion events and water impoundment of the dams on the Changjiang River. The TOC reductions may represent synchronous responses of sedimentary TOC and resultant ecological effects on the inner shelf of the East China Sea to the water impoundment of the dams. These new TOC records reflect the interaction between natural and anthropogenic processes and, accordingly, provide a deep insight and important references for assessing marine ecological effects resulting from water impoundment of largescale dams.

A generic model of contaminant migration from uranium tailings impoundments

International Nuclear Information System (INIS)

Shepherd, T.A.; Brown, S.E.

1982-01-01

This paper presents an analytical hydrogeochemical model based upon acid consumption-neutralization front movement. The development of contaminant plumes is discussed and distinct zones within these plumes are identified and characterized. The most important process influencing the rate and extent of contaminant migration at acid-leach uranium tailings impoundments is the neutralization of seepage water by soils along ground water flow paths. The chemical characteristics of the ground water is determined in order to identify and characterize zones within migrating plumes of tailings-derived water. It is concluded that the characterization of specific zones is useful in the interpretation of existing conditions, in the evaluation of future migration, and in the determination of appropriate models for the specific situation

Microcrustaceans (Branchiopoda and Copepoda) of Wetland Ponds and Impoundments on the Savannah River Site, Aiken, South Carolina

Energy Technology Data Exchange (ETDEWEB)

Adrienne E. DeBiase; Barbara E. Taylor

2005-09-21

The United States Department of Energy's Savannah River Site (SRS) in Aiken, Allendale, and Barnwell Counties, South Carolina, contains an abundance of freshwater wetlands and impoundments. Four large impoundments, as well as several small, abandoned farm and mill ponds, and about 400 Carolina bays and other small, isolated depression wetland ponds are located within the 893 km2 area of the SRS. Crustaceans of the orders Branchiopoda and Copepoda are nearly ubiquitous in these water bodies. Although small in size, these organisms are often very abundant. They consequently play an important trophic role in freshwater food webs supporting fish, larval salamanders, larval insects, and numerous other animals, aquatic and terrestrial. This report provides an introduction to the free-living microcrustaceans of lentic water bodies on the SRS and a comprehensive list of species known to occur there. Occurrence patterns are summarized from three extensive survey studies, supplemented with other published and unpublished records. In lieu of a key, we provide a guide to taxonomic resources and notes on undescribed species. Taxa covered include the orders Cladocera, Anostraca, Laevicaudata, and Spinicaudata of the Subclass Branchiopoda and the Superorders Calanoida and Cyclopoida of Subclass Copepoda. Microcrustaceans of the Superorder Harpacticoida of the Subclass Copepoda and Subclass Ostracoda are also often present in lentic water bodies. They are excluded from this report because they have not received much study at the species level on the SRS.

Sulfide oxidation and acid mine drainage formation within two active tailings impoundments in the Golden Quadrangle of the Apuseni Mountains, Romania.

Science.gov (United States)

Sima, Mihaela; Dold, Bernhard; Frei, Linda; Senila, Marin; Balteanu, Dan; Zobrist, Jurg

2011-05-30

Sulfidic mine tailings have to be classified as one of the major source of hazardous materials leading to water contamination. This study highlights the processes leading to sulfide oxidation and acid mine drainage (AMD) formation in the active stage of two tailings impoundments located in the southern part of the Apuseni Mountains, in Romania, a well-known region for its long-term gold-silver and metal mining activity. Sampling was undertaken when both impoundments were still in operation in order to assess their actual stage of oxidation and long-term behavior in terms of the potential for acid mine drainage generation. Both tailings have high potential for AMD formation (2.5 and 3.7 wt.% of pyrite equivalent, respectively) with lesser amount of carbonates (5.6 and 3.6 wt.% of calcite equivalent) as neutralization potential (ABA=-55.6 and -85.1 tCaCO(3)/1000 t ) and showed clear signs of sulfide oxidation yet during operation. Sequential extraction results indicate a stronger enrichment and mobility of elements in the oxidized tailings: Fe as Fe(III) oxy-hydroxides and oxides (transformation from sulfide minerals, leaching in oxidation zone), Ca mainly in water soluble and exchangeable form where gypsum and calcite are dissolved and higher mobility of Cu for Ribita and Pb for Mialu. Two processes leading to the formation of mine drainage at this stage could be highlighted (1) a neutral Fe(II) plume forming in the impoundment with ferrihydrite precipitation at its outcrop and (2) acid mine drainage seeping in the unsaturated zone of the active dam, leading to the formation of schwertmannite at its outcrop. Copyright © 2011 Elsevier B.V. All rights reserved.

Dynamics of dissolved organic matter in riverine sediments affected by weir impoundments: Production, benthic flux, and environmental implications.

Science.gov (United States)

Chen, Meilian; Kim, Sung-Han; Jung, Heon-Jae; Hyun, Jung-Ho; Choi, Jung Hyun; Lee, Hyo-Jin; Huh, In-Ae; Hur, Jin

2017-09-15

In order to understand the characteristics and dynamics of dissolved organic matter (DOM) in the sediment of rivers affected by impoundments, we examined the vertical profiles and the benthic fluxes of DOM in four different core sediments located at upstream sites of weirs in major rivers of South Korea. In three out of four sites, exponential accumulation of dissolved organic carbon (DOC) with depth was observed with the signature of seasonal variability. Except for the site displaying a below-detection limit of Fe(II), the general accumulation trends of DOC with depth was concurrent with the increases of Fe(II) and NH 4 + and the decrease of PO 4 3- , signifying a close linkage of the DOM dynamics with anaerobic respiration via iron reduction, an important early diagenesis pathway. The estimated benthic fluxes from the cores revealed that the sediments likely serve as DOC, chromophoric DOM (CDOM), and fluorescent DOM (FDOM) sources to the overlying water. The benthic effluxes based on DOC were comparable to the ranges previously reported in lake and coastal areas, and those of CDOM and FDOM showed even higher levels. These findings imply that impoundment-affected river systems would change the DOM composition of the overlying water, ultimately influencing the subsequent water treatment processes such as disinfection byproducts production and membrane fouling. A simple mass balance model indicated that the impoundment-affected river sediments may operate as a net carbon sink in the environments due to a greater extent of sedimentation compared to the estimated benthic efflux and sediment biological respiration. Copyright © 2017 Elsevier Ltd. All rights reserved.

Recovery of the Three-Gorges Reservoir Impoundment Signal from ICESat altimetry and GRACE

Science.gov (United States)

Carabajal, C. C.; Boy, J.; Luthcke, S. B.; Harding, D. J.; Rowlands, D. D.; Lemoine, F. G.

2006-12-01

The Three Gorges Dam along the Yangtze River in China is one of the largest dams in the world. The water impoundment of the Three-Gorges Reservoir started in June 2003, and the volume of water will continuously increase up to about 40 km3 in 2009, over a length of about 600 km. Although water-level changes along the Yangtze River and the Three Gorges Reservoir are measured by in situ water gauges, access to these data can be quite difficult. Estimates of inland water height and extent can also be recovered from altimetry measurements performed from satellite platforms, such as those acquired by the Geoscience laser Altimetry System (GLAS) on board the Ice, Cloud and Land Elevation Satellite (ICESat). ICESat has produced a comprehensive, highly precise, set of along-track elevation measurements, every three months since its launch in 2003, which intersect the Yangtze River along its East-West extent. In addition, the water impoundment of major artificial reservoirs induces variations of global geodetic quantities, such as the gravity field and Earth rotation (Chao, 1995, Boy & Chao, 2002). Water level changes within the reservoir are compared to GRACE (Gravity Recovery And Climate Experiment) recovered water mass changes. In addition, we compare the GRACE observations of mass change in the Yangtze region to hydrological changes computed from different global soil-moisture and snow models, such as GLDAS (Global Land Data Assimilation System).

Geochemical and mineralogical characterization of a neutral, low-sulfide/high-carbonate tailings impoundment, Markušovce, eastern Slovakia.

Science.gov (United States)

Hiller, Edgar; Petrák, Marián; Tóth, Roman; Lalinská-Voleková, Bronislava; Jurkovič, L'ubomír; Kučerová, Gabriela; Radková, Anežka; Sottník, Peter; Vozár, Jaroslav

2013-11-01

mineral assemblage and their occurrence follows the order: chalcopyrite > pyrite > tetrahedrite>arsenopyrite. The mineralogical composition of the tailings corresponds well to the primary mineralization mined. The neutralization capacity of the tailings is high, as confirmed by the values of neutralization potential to acid generation potential ratio, ranging from 6.7 to 63.9, and neutral to slightly alkaline pH of the tailings (paste pH 7.16-8.12) and the waters (pH 7.00-8.52). This is explained by abundant occurrence of carbonate minerals in the tailings, which readily neutralize the acidity generated by sulfide oxidation. The total solid-phase concentrations of metal(loid)s decrease as Cu>Sb>Hg>As and reflect the proportions of sulfides present in the tailings. Sulfide oxidation generally extends to a depth of 2 m. μ-XRD and EMPA were used to study secondary products developed on the surface of sulfide minerals and within the tailings. The main secondary minerals identified are goethite and X-ray amorphous Fe oxyhydroxides and their occurrence decreases with increasing tailings depth. Secondary Fe phases are found as mineral coatings or individual grains and retain relatively high amounts of metal(loid)s (up to 57.6 wt% Cu, 1.60 wt% Hg, 23.8 wt% As, and 2.37 wt% Sb). Based on batch leaching tests and lysimeter results, the mobility of potentially toxic elements in the tailings is low. The limited mobility of metals and metalloids is due to their retention by Fe oxyhydroxides and low solubilities of metal(loid)-bearing sulfides. The observations are consistent with PHREEQC calculations, which predict the precipitation of Fe oxyhydroxides as the main solubility-controlling mineral phases for As, Cu, Hg, and Sb. Waters discharging from tailings impoundment are characterized by a neutral to slightly alkaline pH (7.52-7.96) and low concentrations of dissolved metal(loid)s (tailings impoundment.

Presentations from the 1992 Coal Mining Impoundment Informational Meeting

Energy Technology Data Exchange (ETDEWEB)

1993-12-31

On May 20 and 21, 1992, the MSHA Coal Mining Impoundment Informational Meeting was held at the National Mine Health and Safety Academy in Beckley, West Virginia. Fifteen presentations were given on key issues involved in the design and construction of dams associated with coal mining. The attendees were told that to improve the consistency among the plan reviewers, engineers from the Denver and Pittsburgh Technical Support Centers meet twice annually to discuss specific technical issues. It was soon discovered that the topics being discussed needed to be shared with anyone involved with coal waste dam design, construction, or inspection. The only way to accomplish that goal was through the issuance of Procedure Instruction Letters. The Letters present a consensus of engineering philosophy that could change over time. They do not present policy or carry the force of law. Currently, thirteen position papers have been disseminated and more will follow as the need arises. The individual paper were not even entered into the database.

A Risk Assessment Approach to Manage Inundation of Elseya albagula Nests in Impounded Waters: A Win-Win Situation?

Science.gov (United States)

McDougall, A. J.; Espinoza, T.; Hollier, C.; Limpus, D. J.; Limpus, C. J.

2015-03-01

A risk assessment process was used to trial the impact of potential new operating rules on the frequency of nest inundation for the White-throated snapping turtle, Elseya albagula, in the impounded waters of the Burnett River, Queensland, Australia. The proposed operating rules would increase the barrage storage level during the turtle nesting season (May-July) and then would be allowed to reduce to a lower level for incubation for the rest of the year. These proposed operating rules reduce rates of nest inundation by altering water levels in the Ben Anderson Barrage impoundment of the Burnett River. The rules operate throughout the turtle reproductive period and concomitantly improve stability of littoral habitat and fishway operation. Additionally, the proposed rules are expected to have positive socio-economic benefits within the region. While regulated water resources will inherently have a number of negative environmental implications, these potential new operating rules have the capacity to benefit the environment while managing resources in a more sustainable manner. The operating rules have now been enacted in subordinate legislation and require the operator to maintain water levels to minimize turtle nest inundation.

Analysis of spatial distribution and inventory of radioactivity within the uranium mill tailings impoundment

Directory of Open Access Journals (Sweden)

D. O. Bugai

2015-10-01

Full Text Available Results are presented of the characterization of radioactivity inventory of Zapadnoe uranium mill tailings impoundment situated at Pridneprovsky Chemical Plant (PChP; Dneprodzerzhinsk, Ukraine. Analyses of radioactivity data set based on analytical studies of core material from 15 characterization boreholes allowed significantly refining waste volume and radioactivity inventory estimates. Geostatistical analyses using variogram function have established that radioactivity distribution in Zapadnoe tailings is characterized by regular spatial correlation patterns. Ordinary kriging method was applied to assess distribution of radioactivity in 3D. Results of statistical analyses suggest significant redistribution of uranium in the dissolved form in the residues (presumably due to water infiltration process. The developed structural model for radioactivity distribution is used for further risk assessment analyses. Derived radioactivity correlation scales can be used for optimization of sample collection when characterizing the PChP Site and similar contaminated sites elsewhere.

Reservoir Operation Rules for Controlling Algal Blooms in a Tributary to the Impoundment of Three Gorges Dam

Directory of Open Access Journals (Sweden)

Jijian Lian

2014-10-01

Full Text Available Since the first impoundment of Three Gorges Dam in 2003, algal blooms occur frequently in the near-dam tributaries. It is widely recognized that the impoundment-induced change in hydrodynamic condition with the lower current velocity will make the eutrophication problem even more severe when an excessive amount of nutrients is already loaded into a reservoir and/or its tributaries. Operation tests carried out by Three Gorges Corporation in 2010 point to some feasible reservoir operation schemes that may have positive impacts on reducing the algal bloom level. In our study, an attempt is made to obtain, through a numerical hydrodynamic and water quality modeling and analysis, the reservoir operation rules that would reduce the level of algal blooms in the Xiangxi River (XXR, a near-dam tributary. Water movements and algal blooms in XXR are simulated and analyzed under different scenarios of one-day water discharge fluctuation or two-week water level variation. The model results demonstrate that the reservoir operations can further increase the water exchange between the mainstream of the Three Gorges Reservoir (TGR and the XXR tributary and thus move a larger amount of algae into the deep water where it will die. Analysis of the model results indicate that the water discharge fluctuation constituted of a lower valley-load flow and a larger flow difference for the short-term operation (within a day, the rise in water level for the medium-term operation (e.g., over weeks, and the combination of the above two for the long-term operation (e.g., over months can be the feasible reservoir operation rules in the non-flood season for TGR.

Fishers' knowledge identifies environmental changes and fish abundance trends in impounded tropical rivers.

Science.gov (United States)

Hallwass, Gustavo; Lopes, Priscila F; Juras, Anastácio A; Silvano, Renato A M

2013-03-01

The long-term impacts of large hydroelectric dams on small-scale fisheries in tropical rivers are poorly known. A promising way to investigate such impacts is to compare and integrate the local ecological knowledge (LEK) of resource users with biological data for the same region. We analyzed the accuracy of fishers' LEK to investigate fisheries dynamics and environmental changes in the Lower Tocantins River (Brazilian Amazon) downstream from a large dam. We estimated fishers' LEK through interviews with 300 fishers in nine villages and collected data on 601 fish landings in five of these villages, 22 years after the dam's establishment (2006-2008). We compared these two databases with each other and with data on fish landings from before the dam's establishment (1981) gathered from the literature. The data obtained based on the fishers' LEK (interviews) and from fisheries agreed regarding the primary fish species caught, the most commonly used type of fishing gear (gill nets) and even the most often used gill net mesh sizes but disagreed regarding seasonal fish abundance. According to the interviewed fishers, the primary environmental changes that occurred after the impoundment were an overall decrease in fish abundance, an increase in the abundance of some fish species and, possibly, the local extinction of a commercial fish species (Semaprochilodus brama). These changes were corroborated by comparing fish landings sampled before and 22 years after the impoundment, which indicated changes in the composition of fish landings and a decrease in the total annual fish production. Our results reinforce the hypothesis that large dams may adversely affect small-scale fisheries downstream and establish a feasible approach for applying fishers' LEK to fisheries management, especially in regions with a low research capacity.

Hydrologic Change during the Colonial Era of the United States: Beavers and the Energy Cost of Impoundments (Invited)

Science.gov (United States)

Green, M. B.; Bain, D. J.; Arrigo, J. S.; Duncan, J. M.; Kumar, S.; Parolari, A.; Salant, N.; Vorosmarty, C. J.; Aloysius, N. R.; Bray, E. N.; Ruffing, C. M.; Witherell, B. B.

2009-12-01

Europeans colonized North America in the early 17th century with intentions ranging between long-term inhabitation and quick extraction of resources for economic gain in Europe. Whatever the intentions, the colonists relied on the landscape for resources resulting in dramatic change to the forest and fur-bearing mammal population. We demonstrate that initial exploitation of North American forest and furs caused a substantial decrease in mean water residence time (τ) between 1600 and 1800 A.D. That loss, which regionally changed from 51 to 41 days, contrasts with conventional wisdom that humans tend to diminish variability in water resources by increasing storage capacity and thus increasing τ. The loss of τ resulted from over-hunted beaver for the hat market in Europe. Analysis suggests that colonial era demographics and economics did not allow human resource allocation to impoundment construction on a level matching the historic beaver effort. However, the τ appears to have regionally increased during the 19th century, suggesting that humans eventually began replacing the water storage lost with the beaver. The analysis highlights the energy cost of impounding water, which is likely to continue to be an important factor given the increasing need for stable water resources and finite energy resources.

Survivability of ancient man-made earthen mounds: implications for uranium mill tailings impoundments

International Nuclear Information System (INIS)

Lindsey, C.G.; Mishima, J.; King, S.E.; Walters, W.H.

1983-06-01

As part of a study for the Nuclear Regulatory Commission (NRC), the Pacific Northwest Laboratory (PNL) is investigating long-term stabilization techniques for uranium mill impoundments. Part of this investigation involves the design of a rock armoring blanket (riprap) to mitigate wind and water erosion of the underlying soil cover, which in turn prevents exposure of the tailings to the environment. However, the need for the armoring blanket, as well as the blanket's effectiveness, depends on the stability of the underlying soil cap (radon suppression cover) and on the tailings themselves. Compelling evidence in archaeological records suggests that large man-made earthen structures can remain sound and intact for time periods comparable to those required for the stabilization of the tailings piles if properly constructed. We present archaeological evidence on the existence and survivability of man-made earthen and rock structures through specific examples of such structures from around the world. We also review factors contributing to their survival or destruction and address the influence of climate, building materials, and construction techniques on survivability

40 CFR 270.17 - Specific part B information requirements for surface impoundments.

Science.gov (United States)

2010-07-01

... migration of any hazardous constituents into the ground water or surface water at any future time; (2) The....19 of this chapter; (5) Proposed action leakage rate, with rationale, if required under § 264.222 of..., including the double liner system, leak detection system, cover system, and appurtenances for control of...

Dam water quality study. Report to Congress

International Nuclear Information System (INIS)

1989-05-01

The objective of the report is to identify water quality effects attributable to the impoundment of water by dams as required by Section 524 of the Water Quality Act of 1987. The document presents a study of water quality effects associated with impoundments in the U.S.A

Effects of dams in river networks on fish assemblages in non-impoundment sections of rivers in Michigan and Wisconsin, USA

Science.gov (United States)

Stewart, Jana S.; Lizhu Wang,; Infante, Dana M.; Lyons, John D.; Arthur Cooper,

2011-01-01

Regional assessment of cumulative impacts of dams on riverine fish assemblages provides resource managers essential information for dam operation, potential dam removal, river health assessment and overall ecosystem management. Such an assessment is challenging because characteristics of fish assemblages are not only affected by dams, but also influenced by natural variation and human-induced modification (in addition to dams) in thermal and flow regimes, physicochemical habitats and biological assemblages. This study evaluated the impacts of dams on river fish assemblages in the non-impoundment sections of rivers in the states of Michigan and Wisconsin using multiple fish assemblage indicators and multiple approaches to distinguish the influences of dams from those of other natural and human-induced factors. We found that environmental factors that influence fish assemblages in addition to dams should be incorporated when evaluating regional effects of dams on fish assemblages. Without considering such co-influential factors, the evaluation is inadequate and potentially misleading. The role of dams alone in determining fish assemblages at a regional spatial scale is relatively small (explained less than 20% of variance) compared with the other environmental factors, such as river size, flow and thermal regimes and land uses jointly. However, our results do demonstrate that downstream and upstream dams can substantially modify fish assemblages in the non-impoundment sections of rivers. After excluding river size and land-use influences, our results clearly demonstrate that dams have significant impacts on fish biotic-integrity and habitat-and-social-preference indicators. The influences of the upstream dams, downstream dams, distance to dams, and dam density differ among the fish indicators, which have different implications for maintaining river biotic integrity, protecting biodiversity and managing fisheries.

Proceedings of the 15. annual British Columbia MEND ML/ARD workshop : the management of tailings and tailings impoundments

International Nuclear Information System (INIS)

2009-02-01

This Mine Environment Neutral Drainage (MEND) workshop was held to promote the exchange of information and ideas on environmental protection and reclamation associated with mining. The workshop covered a broad spectrum of reclamation issues and the key environmental challenges facing the mining industry, such as acid mine drainage (AMD) control, and metal leaching and acid rock drainage (ML/ARD). The theme for the 2008 workshop was the management of tailings and tailings impoundments. Topics of discussion included hydrogeology and geochemistry; tailings disposal; mitigation; closure plans; and postclosure performance. The emphasis was on full-scale case studies, practical constraints and sustaining successful disposal strategies and remediation. The session on tailings management reviewed overarching policies and practices; methods of subaerial tailings disposal and case studies of tailings management; and detailed investigations of geochemical properties and processes. The conference featured 22 presentations, of which 4 have been catalogued separately for inclusion in this database. refs., tabs., figs

Underground coal mine subsidence impacts on surface water

International Nuclear Information System (INIS)

Stump, D.E. Jr.

1992-01-01

This paper reports that subsidence from underground coal mining alters surface water discharge and availability. The magnitude and areal extent of these impacts are dependent on many factors, including the amount of subsidence, topography, geology, climate, surface water - ground water interactions, and fractures in the overburden. There alterations may have positive and/or negative impacts. One of the most significant surface water impacts occurred in July 1957 near West Pittston, Pennsylvania. Subsidence in the Knox Mine under the Coxton Yards of the Lehigh Valley Railroad allowed part of the discharge in the Susquehanna River to flow into the mine and create a crater 200 feet in diameter and 300 feet deep. Fourteen railroad gondola cars fell into the hole which was eventually filled with rock, sand, and gravel. Other surface water impacts from subsidence may include the loss of water to the ground water system, the gaining of water from the ground water system, the creation of flooded subsidence troughs, the increasing of impoundment storage capacity, the relocation of water sources (springs), and the alteration of surface drainage patterns

40 CFR 264.227 - Emergency repairs; contingency plans.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Emergency repairs; contingency plans... FACILITIES Surface Impoundments § 264.227 Emergency repairs; contingency plans. (a) A surface impoundment... days after detecting the problem. (c) As part of the contingency plan required in subpart D of this...

40 CFR 264.231 - Special requirements for hazardous wastes FO20, FO21, FO22, FO23, FO26, and FO27.

Science.gov (United States)

2010-07-01

... HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL FACILITIES Surface Impoundments § 264.231 Special requirements for hazardous wastes FO20, FO21, FO22, FO23, FO26, and FO27. (a) Hazardous Wastes FO20, FO21, FO22... surface impoundments managing hazardous wastes FO20, FO21, FO22, FO23, FO26, and FO27 in order to reduce...

Reclamation plans at uranium mill tailings sites

International Nuclear Information System (INIS)

Abt, S.R.; Nelson, J.D.

1990-01-01

Long-term stability of waste impoundments is of concern because of the long time periods over which various types of waste may remain active. Over the past decade much technology has been developed specifically for reclamation of uranium mill tailings impoundments. Aspects of this technology will be discussed here and is presented as also being directly applicable to reclamation of industrial waste impoundments in general. The paper discusses Title I and Title II sites which represent two different generations in uranium tailings impoundment construction. The comparison between the two represent differences in philosophies as well as in impoundment type. Reclamation of uranium mill tailings impoundments in the U.S. is controlled by Federal legislation, which has set forth the regulatory framework for reclamation plan approval. Title I requirements govern government owned inactive sites and Title II requirements govern active tailings impoundments or those operated by private industries. While the Title I and Title II designation may result in a slightly different regulatory process, reclamation of uranium tailings sites has the same. Differences between Title I and Title II reclamation plans to achieve surface stability relate primarily to the embankment and surface covers. The differences in the cover designs result from site-specific conditions, rather than from differences in engineering approaches or the regulatory process. This paper discusses the site-specific conditions that affect the selection of cover designs, and provides a comparative example to illustrate the effect of this condition

Effect of fishing effort on catch rate and catchability of largemouth bass in small impoundments

Science.gov (United States)

Wegener, M. G.; Schramm, Harold; Neal, J. W.; Gerard, P.D.

2018-01-01

Largemouth bass Micropterus salmoides (Lacepède) catch rates decline with sustained fishing effort, even without harvest. It is unclear why declines in catch rate occur, and little research has been directed at how to improve catch rate. Learning has been proposed as a reason for declining catch rate, but has never been tested on largemouth bass. If catch rate declines because fish learn to avoid lures, periods of no fishing could be a management tool for increasing catch rate. In this study, six small impoundments with established fish populations were fished for two May to October fishing seasons to evaluate the effect of fishing effort on catch rate. Closed seasons were implemented to test whether a 2‐month period of no fishing improved catch rates and to determine whether conditioning from factors other than being captured reduced catch rate. Mixed‐model analysis indicated catch rate and catchability declined throughout the fishing season. Catch rate and catchability increased after a 2‐month closure but soon declined to the lowest levels of the fishing season. These changes in catch rate and catchability support the conclusion of learned angler avoidance, but sustained catchability of fish not previously caught does not support that associative or social learning affected catchability.

40 CFR 264.1085 - Standards: Surface impoundments.

Science.gov (United States)

2010-07-01

... materials of construction and designing the cover and closure devices shall include: Organic vapor... closure device in the closed position, as applicable. (B) To remove accumulated sludge or other residues... construction and designing the cover and closure devices shall include: Organic vapor permeability; the effects...

40 CFR 265.1086 - Standards: Surface impoundments.

Science.gov (United States)

2010-07-01

... materials of construction and designing the cover and closure devices shall include: Organic vapor... closure device in the closed position, as applicable. (B) To remove accumulated sludge or other residues... construction and designing the cover and closure devices shall include: Organic vapor permeability; the effects...

Use of special oedometer tests for the remediation of large uranium mill tailings impoundments at Wismut, Germany

International Nuclear Information System (INIS)

Barnekow, U.; Paul, M.

2002-01-01

The paper presents the use of recently developed special oedometer tests for designing the remediation of large uranium tailings ponds at WISMUT, Germany. Uranium ore mining and milling in eastern Germany by the former Soviet-German WISMUT company lasted from 1946 to 1990. Wastes from the hydrometallurgical uranium extraction processes were discharged into large tailings impoundments covering a total area of 5.5 km 2 and containing about 150 x 10 6 m 3 of uranium mill tailings. Tailings pond remediation is ongoing by in-place decommissioning with dewatering by technical means. Geotechnical properties and the most suitable so-called non-linear finite strain consolidation behaviour of fine uranium mill tailings are described. Decommissioning techniques comprise, among others, interim covering of under consolidated fine tailings, contouring of tailings surfaces and final covering. Contouring, in particular, has a huge potential for optimization in terms of cost reduction. For contouring total settlement portions, the spatial distribution of differential settlement portions and the time-dependent settlement rates, especially of the cohesive fine uranium mill tailings are of critical importance. A new special oedometer KD 314 S has been developed to generate all the input data needed to derive the fundamental geotechnical relationships of void ratio vs. effective stress and of permeability coefficient vs. void ratio for consolidation calculations. Since December 1999 the new special oedometer KD 314 S has been working successfully on fine uranium mill tailings from both acid and from soda alkaline milling. Results coincide with non-linear finite strain consolidation theory. The geotechnical functions derived were used as input parameters for consolidation modelling. An example of the consolidation modelling on Helmsdorf tailings pond is presented. (author)

Treatability studies performed in support of an engineering evaluation/cost analysis

International Nuclear Information System (INIS)

Myers, J.M.; Mueller, J.P.; Sundquist, J.A.; Moore, G.W.

1995-01-01

The Southern Shipbuilding Corporation (SSC) site is located on 54 acres of wooded land adjacent to Bayou Bonfouca, approximately 1.8 miles downstream of the Bayou Bonfouca National Priorities List (NPL) Superfund site in Slidell, St. Tammany Parish, Louisiana. Two one-acre, impoundments on the SSC site were used to store wastes generated from vessel cleaning. Wastes stored in the impoundments are migrating into Bayou Bonfouca, which empties into Lake Pontchartrain. In addition, the impoundments are frequently invaded by flood waters. The US EPA Emergency Response Branch (EPA-ERB) performed a site investigation which indicated that the majority of the contamination is petroleum-related and that the compounds of concern are polycyclic aromatic hydrocarbons (PARs). The wastes are generally contained with the two impoundments and surrounding soils. As part of an Engineering Evaluation/Cost Basis (EE/CA) of potential response action alternatives, four treatability studies were performed. A thermal treatment (incineration) study was performed at the EPA's Incineration Research Facility (IRF). Biodegradation remedy selection feasibility assessment was conducted on-site. A remedy screening soil washing study was also performed by TAT. A solidification/stabilization (S/S) study was conducted through EPA's Risk Reduction Engineering Laboratory (RREL) to ascertain if the PAHs could be immobilized within a solid matrix. Experimental objectives, dead methodology and conclusions for these studies are presented as they relate to potential response actions being evaluated at the SSC site

Sediment transport to and from small impoundments in northeast Kansas, March 2009 through September 2011

Science.gov (United States)

Foster, Guy M.; Lee, Casey J.; Ziegler, Andrew C.

2012-01-01

The U.S. Geological Survey, in cooperation with the Kansas Water Office, investigated sediment transport to and from three small impoundments (average surface area of 0.1 to 0.8 square miles) in northeast Kansas during March 2009 through September 2011. Streamgages and continuous turbidity sensors were operated upstream and downstream from Atchison County, Banner Creek, and Centralia Lakes to study the effect of varied watershed characteristics and agricultural practices on sediment transport in small watersheds in northeast Kansas. Atchison County Lake is located in a predominantly agricultural basin of row crops, with wide riparian buffers along streams, a substantial amount of tile drainage, and numerous small impoundments (less than 0.05 square miles; hereafter referred to as “ponds”). Banner Creek Lake is a predominantly grassland basin with numerous small ponds located in the watershed, and wide riparian buffers along streams. Centralia Lake is a predominantly agricultural basin of row crops with few ponds, few riparian buffers along streams, and minimal tile drainage. Upstream from Atchison County, Banner Creek, and Centralia Lakes 24, 38, and 32 percent, respectively, of the total load was transported during less than 0.1 percent (approximately 0.9 days) of the time. Despite less streamflow in 2011, larger sediment loads during that year indicate that not all storm events transport the same amount of sediment; larger, extreme storms during the spring may transport much larger sediment loads in small Kansas watersheds. Annual sediment yields were 360, 400, and 970 tons per square mile per year at Atchison County, Banner, and Centralia Lake watersheds, respectively, which were less than estimated yields for this area of Kansas (between 2,000 and 5,000 tons per square mile per year). Although Centralia and Atchison County Lakes had similar percentages of agricultural land use, mean annual sediment yields upstream from Centralia Lake were about 2.7 times

Evidence for serial discontinuity in the fish community of a heavily impounded river

Science.gov (United States)

Miranda, Leandro E.; Dembkowski, D.J.

2016-01-01

In the Tennessee River, USA, we examined lengthwise patterns in fish community structure and species richness within and among nine reservoirs organized in sequence and connected through navigational locks. Within reservoirs, the riverine, transition and lacustrine zones supported distinct, although overlapping, nearshore fish assemblages; differences were also reflected in measures of species richness. Spatial patterns were most apparent for rheophilic species, which increased in species richness and representation upstream within each reservoir and downstream across the chain of reservoirs. This pattern resembled a sawtooth wave, with the amplitude of the wave peaking in the riverine zone below each dam, and progressively higher wave amplitude developing downstream in the reservoir chain. The observed sawtooth pattern supports the serial discontinuity concept in that the continuity of the riverine fish community is interrupted by the lacustrine conditions created behind each dam. Upstream within each reservoir, and downstream in the chain of reservoirs, habitat characteristics become more riverine. To promote sustainability of rheophilic fishes and maintain biodiversity in impounded rivers, conservation plans could emphasize maintenance and preservation of riverine environments of the reservoir's upper reaches, while remaining cognizant of the broader basin trends that provide opportunities for a lengthwise array of conservation and management policy. 

Fugitive emissions control on dry copper tailing with crushed rock armor

International Nuclear Information System (INIS)

Haase, E.F.

1992-01-01

Four inactive copper tailing impoundments totalling 1,900 acres near Ajo in southwestern Arizona were covered on horizontal surfaces with a 2 in. nominal thickness of crushed rock to control particulate emissions. The tailings are typically dominated by sand-sized particles but may also include significant PM 10 fractions towards the centers of the impoundments. The technology was selected by Phelps Dodge Corporation, after investigation of several alternatives, as a permanent and practical cover that essentially eliminates fugitive emissions. It simulates the natural desert pavement that characterizes this arid area of the Sonoran Desert. Rocky overburden was crushed to minus 3 in. diameter and broadcast on dry surfaces of tailing impoundments with all-terrain, balloon-tired spreaders. Stony residues in the rock armor tend to cement together following rainfall, forming a crust that enhances surface stability and erosion control. Slopes with windblown tailing deposition were covered to a nominal 6 in. thickness by conventional dozer pushing and blading of minus 10 in. rock over the sides. Athel trees, planted extensively since 1970 on two of the four inactive impoundments, provided partial control of fugitives, but were subjected to harsh environmental conditions, including abrasion from saltating particles. The rock armor functions as a mulch which is expected to improve water relations for existing vegetation and areas seeded with native species. New surface microenvironments, and the virtual elimination of surface creep and saltation, are expected to support native plant growth under favorable climatic conditions

30 CFR 77.216-2 - Water, sediment, or slurry impoundments and impounding structures; minimum plan requirements...

Science.gov (United States)

2010-07-01

... SAFETY AND HEALTH MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND... instrumentation. (9) Graphs showing area-capacity curves. (10) A statement of the runoff attributable to the probable maximum precipitation of 6-hour duration and the calculations used in determining such runoff. (11...

Quantifying downstream impacts of impoundment on flow regime and channel planform, lower Trinity River, Texas

Science.gov (United States)

Wellmeyer, Jessica L.; Slattery, Michael C.; Phillips, Jonathan D.

2005-07-01

As human population worldwide has grown, so has interest in harnessing and manipulating the flow of water for the benefit of humans. The Trinity River of eastern Texas is one such watershed greatly impacted by engineering and urbanization. Draining the Dallas-Fort Worth metroplex, just under 30 reservoirs are in operation in the basin, regulating flow while containing public supplies, supporting recreation, and providing flood control. Lake Livingston is the lowest, as well as largest, reservoir in the basin, a mere 95 km above the Trinity's outlet near Galveston Bay. This study seeks to describe and quantify channel activity and flow regime, identifying effects of the 1968 closure of Livingston dam. Using historic daily and peak discharge data from USGS gauging stations, flow duration curves are constructed, identifying pre- and post-dam flow conditions. A digital historic photo archive was also constructed using six sets of aerial photographs spanning from 1938 to 1995, and three measures of channel activity applied using a GIS. Results show no changes in high flow conditions following impoundment, while low flows are elevated. However, the entire post-dam period is characterized by significantly higher rainfall, which may be obscuring the full impact of flow regulation. Channel activity rates do not indicate a more stabilized planform following dam closure; rather they suggest that the Trinity River is adjusting itself to the stress of Livingston dam in a slow, gradual process that may not be apparent in a modern time scale.

Holocene Record of Major and Trace Components in the Sediments of an Urban Impoundment on the Mississippi River: Lake Pepin, Minnesota and Wisconsin

Science.gov (United States)

Dean, Walter E.

2009-01-01

Lake Pepin is a natural impoundment formed by damming of the Mississippi River about 9,180 radiocarbon years ago (19,600 calendar years) by an alluvial fan deposited by the Chippewa River, a tributary of the Mississippi in Wisconsin. Unique among 26 Mississippi River impoundments, Lake Pepin has stratigraphically preserved Holocene materials, including pollutants, that have been transported down the Mississippi. This natural Holocene record can then be compared to changes that have occurred since European settlement (ca. AD 1830), and since enactment of clean air and water legislation. The most immediate response to settlement in the sediments of Lake Pepin was an increase in bulk-sediment accumulation rate. This was accompanied by gradual increases in concentrations of phosphorus (P), and organic carbon (OC), followed by dramatic increases in these elements beginning about 1940. The increase in P was far greater than any of the minor fluctuations in P that occurred throughout the Holocene, but the increase in OC was comparable to an increase in OC that occurred in the mid-Holocene. The concentrations of several metals (for example, cadmium [Cd], and lead [Pb]) also are elevated in recent sediments. Increased Cd concentrations lasted only about two decades during the industrial era between World War II and the enactment of clean water standards in the 1970s. Increased Pb emissions, on the other hand, occurred over more than 100 years, first from burning of coal and smelting of lead ores, and then, beginning in the 1930s, burning of leaded gasoline. Concentrations of Pb in the sediments of Lake Pepin decreased to about two times preindustrial levels within a decade of enactment of unleaded gasoline restrictions.

Methane Oxidation and Molecular Characterization of Methanotrophs from a Former Mercury Mine Impoundment

Directory of Open Access Journals (Sweden)

Shaun M. Baesman

2015-06-01

Full Text Available The Herman Pit, once a mercury mine, is an impoundment located in an active geothermal area. Its acidic waters are permeated by hundreds of gas seeps. One seep was sampled and found to be composed of mostly CO2 with some CH4 present. The δ13CH4 value suggested a complex origin for the methane: i.e., a thermogenic component plus a biological methanogenic portion. The relatively 12C-enriched CO2 suggested a reworking of the ebullitive methane by methanotrophic bacteria. Therefore, we tested bottom sediments for their ability to consume methane by conducting aerobic incubations of slurried materials. Methane was removed from the headspace of live slurries, and subsequent additions of methane resulted in faster removal rates. This activity could be transferred to an artificial, acidic medium, indicating the presence of acidophilic or acid-tolerant methanotrophs, the latter reinforced by the observation of maximum activity at pH = 4.5 with incubated slurries. A successful extraction of sterol and hopanoid lipids characteristic of methanotrophs was achieved, and their abundances greatly increased with increased sediment methane consumption. DNA extracted from methane-oxidizing enrichment cultures was amplified and sequenced for pmoA genes that aligned with methanotrophic members of the Gammaproteobacteria. An enrichment culture was established that grew in an acidic (pH 4.5 medium via methane oxidation.

Methane oxidation and molecular characterization of methanotrophs from a former mercury mine impoundment

Science.gov (United States)

Baesman, Shaun; Miller, Laurence G.; Wei, Jeremy H.; Cho, Yirang; Matys, Emily D.; Summons, Roger E.; Welander, Paula V.; Oremland, Ronald S.

2015-01-01

The Herman Pit, once a mercury mine, is an impoundment located in an active geothermal area. Its acidic waters are permeated by hundreds of gas seeps. One seep was sampled and found to be composed of mostly CO2 with some CH4 present. The δ13CH4 value suggested a complex origin for the methane: i.e., a thermogenic component plus a biological methanogenic portion. The relatively 12C-enriched CO2 suggested a reworking of the ebullitive methane by methanotrophic bacteria. Therefore, we tested bottom sediments for their ability to consume methane by conducting aerobic incubations of slurried materials. Methane was removed from the headspace of live slurries, and subsequent additions of methane resulted in faster removal rates. This activity could be transferred to an artificial, acidic medium, indicating the presence of acidophilic or acid-tolerant methanotrophs, the latter reinforced by the observation of maximum activity at pH = 4.5 with incubated slurries. A successful extraction of sterol and hopanoid lipids characteristic of methanotrophs was achieved, and their abundances greatly increased with increased sediment methane consumption. DNA extracted from methane-oxidizing enrichment cultures was amplified and sequenced for pmoA genes that aligned with methanotrophic members of the Gammaproteobacteria. An enrichment culture was established that grew in an acidic (pH 4.5) medium via methane oxidation.

The Effect of Zebra Mussels on Algal Community Structure in an Impounded River System

Science.gov (United States)

Trumble, A. F.; Luttenton, M.

2005-05-01

The zebra mussel, Dreissena polymorpha, invaded the Great Lakes Region in the mid 1980's, and subsequently colonized inland lakes and coastal river systems through secondary invasions. The Muskegon River below Croton Dam was colonized by zebra mussels in 2000 following their introduction into Croton impoundment in the late 1990's. No zebra mussels were found below Croton Dam in 1999 but had increased to 25,000 m-2 by 2001. We examined the affect of zebra mussels on epilithic periphyton communities by comparing plots that were and were not colonized by zebra mussels. Chlorophyll a increased in both treatments over time but was significantly higher in control plots than in zebra mussel plots. The concentration of chlorophyll a in the control plots increased from 14 µgcm-2 to 26 µgcm-2 and the concentration in the zebra mussel plots started at 12 µgcm-2, peaked at 19 µgcm-2, and then decreased to 15 µgcm-2 over a 6 week period. In a related experiment using artificial streams, chlorophyll a increased with increasing zebra mussel density, but differences were not significant. The different trends observed between the two experiments may be explained in part by arthropod invertebrates associated with zebra mussel populations.

Assessment of soil and groundwater contamination by potentially toxic and trace elements in an impounded vehicle scrapyard: Case study: Ribeirão Pires, SP, Brazil

International Nuclear Information System (INIS)

Lange, Camila Neves

2018-01-01

Impounded vehicle scrapyard (IVS) overcrowding is currently a subject of concern in Brazilian scenario. The aim of this study was to assess the total levels of potentially toxic elements (PTEs) and trace elements (TE) in soil and groundwater in an IVS located in the city of Ribeirão Pires. In order to achieve this objective, topsoil, three soil cores and groundwater of three monitoring wells were analyzed. It was verified that the area is mainly affected by three factors: (1) a landfill layer with construction waste; (2) an oily residue from past industrial activities in the area; (3) vehicles parked on topsoil. For the evaluation of the results, statistical techniques, such as multivariate analysis, calculation of pollution, ecological and human health risk index were used. Mass fractions of all PTEs, except Co, Cu, Mo and Zn, were higher than reference values. Hot spots were observed for most elements suggesting vehicular source. The Geoaccumulation Index showed minimal to moderate pollution in soil for most elements, except for As and Ba, which showed higher accumulation than other elements. The enrichment factor pointed to a significant enrichment of As and Pb. Arsenic content in soil may pose a moderate to high potential ecological risk. The results of PTEs and as statistical approaches indicated that As, Ce, Co, Cu, Mn, Nb, Ni, Pb and Zn are mainly from anthropogenic sources. The content of most PTEs in topsoil does not pose a potential human health risk, except Cr content. Groundwater levels for most PTEs were below the drinking water recommendation limits, except Mn and Fe content. (author)

Depletion of barium and radium-226 in Black Sea surface waters over the past thirty years

International Nuclear Information System (INIS)

Kenison Falkner, K.K.; Edmond, J.M.; O'Neill, D.J.; Todd, J.F.; Moore, W.S.

1991-01-01

The nearly landlocked waters of the Black Sea support a valuable fishery, but are also particularly vulnerable to anthropogenic disturbance. Here we use dissolved barium and radium-226 as tracers, to investigate the biogeochemical health of the sea. Both elements are brought to surface waters by vertical mixing of deeper, enriched waters, and by rivers; these inputs should ordinarily be balanced by outflow of surface waters at the Bosphorus, and by biologically mediated removal of 226 Ra-bearing barite. We show, however, that surface-water inventories have been substantially depleted over the past few decades: recent (1988-89) barium concentrations were 1.6 times lower than in 1958 and 1967. These observations suggest that steady-state cycling of these elements has been perturbed by increased primary productivity, presumably fuelled by nutrients from industry and agricultural runoff, and to a lesser extent by decreased fluvial sediment loads owing to extensive impoundment of rivers in the region. (author)

Study of the effect on shelter cat intakes and euthanasia from a shelter neuter return project of 10,080 cats from March 2010 to June 2014

Directory of Open Access Journals (Sweden)

Karen L. Johnson

2014-10-01

Full Text Available Cat impoundments were increasing at the municipal San Jose animal shelter in 2009, despite long-term successful low cost sterilization programs and attempts to lower the euthanasia rate of treatable-rehabilitatable impounds beginning in 2008. San Jose Animal Care and Services implemented a new strategy designed to control overall feral cat reproduction by altering and returning feral cats entering the shelter system, rather than euthanizing the cats. The purpose of this case study was to determine how the program affected the shelter cat intakes over time. In just over four years, 10,080 individual healthy adult feral cats, out of 11,423 impounded at the shelter during this time frame, were altered and returned to their site of capture. Included in the 11,423 cats were 862 cats impounded from one to four additional times for a total of 958 (9.5% recaptures of the previously altered 10,080 cats. The remaining 385 healthy feral cats were euthanized at the shelter from March 2010 to June 2014. Four years into the program, researchers observed cat and kitten impounds decreased 29.1%; euthanasia decreased from over 70% of intakes in 2009, to 23% in 2014. Euthanasia in the shelter for Upper Respiratory Disease decreased 99%; dead cat pick up off the streets declined 20%. Dog impounds did not similarly decline over the four years. No other laws or program changes were implemented since the beginning of the program.

Study of the effect on shelter cat intakes and euthanasia from a shelter neuter return project of 10,080 cats from March 2010 to June 2014

Science.gov (United States)

Cicirelli, Jon

2014-01-01

Cat impoundments were increasing at the municipal San Jose animal shelter in 2009, despite long-term successful low cost sterilization programs and attempts to lower the euthanasia rate of treatable-rehabilitatable impounds beginning in 2008. San Jose Animal Care and Services implemented a new strategy designed to control overall feral cat reproduction by altering and returning feral cats entering the shelter system, rather than euthanizing the cats. The purpose of this case study was to determine how the program affected the shelter cat intakes over time. In just over four years, 10,080 individual healthy adult feral cats, out of 11,423 impounded at the shelter during this time frame, were altered and returned to their site of capture. Included in the 11,423 cats were 862 cats impounded from one to four additional times for a total of 958 (9.5%) recaptures of the previously altered 10,080 cats. The remaining 385 healthy feral cats were euthanized at the shelter from March 2010 to June 2014. Four years into the program, researchers observed cat and kitten impounds decreased 29.1%; euthanasia decreased from over 70% of intakes in 2009, to 23% in 2014. Euthanasia in the shelter for Upper Respiratory Disease decreased 99%; dead cat pick up off the streets declined 20%. Dog impounds did not similarly decline over the four years. No other laws or program changes were implemented since the beginning of the program. PMID:25374785

Uptake of uranium, thorium and radium isotopes by plants growing in dam impoundment Tasotkel and the Lower Shu region (Kazakhstan)

International Nuclear Information System (INIS)

Matveyeva, Ilona; Burkitbayev, Mukhambetkali

2016-01-01

The activity concentrations of isotopes of uranium, thorium and radium-226 in dominant species of plants (Xantium strumarium, Phragmites communis, Artemisia nitrosa and Artemisia serotina) growing on the territories contaminated by uranium industry of Kazakhstan (close to dam impoundment Tasotkel and the Lower Shu region) are presented. The obtained data showed the significant variations of activity concentrations of isotopes of uranium, thorium and radium-226 in above ground parts. The concentrations of most of the investigated radionuclides in the root system are higher than in the aboveground parts; it can be explained by root barrier. It was found that the highest root barrier has Xantium strumarium, especially for uranium isotopes. The concentration ratios of radionuclides were calculated, and as the result it was found that the highest accumulation ability in the investigated region has Artemisia serotina.

Uptake of uranium, thorium and radium isotopes by plants growing in dam impoundment Tasotkel and the Lower Shu region (Kazakhstan)

Energy Technology Data Exchange (ETDEWEB)

Matveyeva, Ilona; Burkitbayev, Mukhambetkali [al-Farabi Kazakh National University, Almaty (Kazakhstan). Faculty of Chemistry and Chemical Technology; Jacimovic, Radojko [Jozef Stefan Institute, Ljubljana (Slovenia). Dept. of Environmental Sciences; Planinsek, Petra; Smodis, Borut [Jozef Stefan Institute, Ljubljana (Slovenia). Dept. of Environmental Sciences; Jozef Stefan International Postgraduate School, Ljubljana (Slovenia)

2016-04-01

The activity concentrations of isotopes of uranium, thorium and radium-226 in dominant species of plants (Xantium strumarium, Phragmites communis, Artemisia nitrosa and Artemisia serotina) growing on the territories contaminated by uranium industry of Kazakhstan (close to dam impoundment Tasotkel and the Lower Shu region) are presented. The obtained data showed the significant variations of activity concentrations of isotopes of uranium, thorium and radium-226 in above ground parts. The concentrations of most of the investigated radionuclides in the root system are higher than in the aboveground parts; it can be explained by root barrier. It was found that the highest root barrier has Xantium strumarium, especially for uranium isotopes. The concentration ratios of radionuclides were calculated, and as the result it was found that the highest accumulation ability in the investigated region has Artemisia serotina.

Estimates of population distributions and tailings areas around licensed uranium mill sites. Final report

International Nuclear Information System (INIS)

Hans, J.M.; Hall, J.B.; Moore, W.E.

1986-08-01

Population distributions and tailings areas were estimated from aerial photography for each of 21 licensed uranium millsites. Approximately 11,600 persons live within 5 kilometers of the tailings impoundments at the millsites. About 82% of these persons live near five of the millsites. No persons were found living within 5 kilometers of six of the millsites. Tailings area measurements include the surface area of tailings in impoundments, heap-leached ore, and carryover tailings in evaporation ponds. Approximately 4,000 acres of tailings surfaces were measured for the 21 millsites. About 55% of the tailings surfaces were dry, 11% wet, and the remainder ponded. The average tailings surface area for the millsites is about 200 acres and ranges from 7 to 813 acres

Nonlinear optical studies of surfaces

International Nuclear Information System (INIS)

Shen, Y.R.

1994-07-01

The possibly of using nonlinear optical processes for surface studies has attracted increasing attention in recent years. Optical second harmonic generation (SHG) and sum frequency generation (SFG), in particular, have been well accepted as viable surface probes. They have many advantages over the conventional techniques. By nature, they are highly surface-specific and has a submonolayer sensitivity. As coherent optical processes, they are capable of in-situ probing of surfaces in hostile environment as well as applicable to all interfaces accessible by light. With ultrafast pump laser pulses, they can be employed to study surface dynamic processes with a subpicosecond time resolution. These advantages have opened the door to many exciting research opportunities in surface science and technology. This paper gives a brief overview of this fast-growing new area of research. Optical SHG from a surface was first studied theoretically and experimentally in the sixties. Even the submonolayer surface sensitivity of the process was noticed fairly early. The success was, however, limited because of difficulties in controlling the experimental conditions. It was not until the early 1980's that the potential of the process for surface analysis was duly recognized. The first surface study by SHG was actually motivated by the then active search for an understanding of the intriguing surface enhanced Raman scattering (SERS). It had been suspected that the enhancement in SERS mainly came from the local-field enhancement due to local plasmon resonances and pointing rod effect on rough metal surfaces. In our view, Raman scattering is a two-photon process and is therefore a nonlinear optical effect

Resource use by the facultative lepidophage Roeboides affinis (Günther, 1868: a comparison of size classes, seasons and environment types related to impoundment

Directory of Open Access Journals (Sweden)

Miriam P. Albrecht

Full Text Available We report the consumption of scales and other food resources by the facultative lepidophage Roeboides affinis in the upper Tocantins River where it was impounded by the Serra da Mesa Hydroelectric Dam. We compared the diet among size classes, between dry and wet seasons, and between sites with distinct water flow characteristics (lotic vs. lentic related to the distance from the dam and phase of reservoir development. As transparency and fish abundance increased after impoundment, we expected a higher consumption of scales in lentic sites. Likewise, habitat contraction, higher transparency and decrease in terrestrial resources availability, would promote a higher consumption of scales. Scales were consumed by 92% of individuals and represented 26% of the total volume of resources ingested by R. affinis. Diet composition varied significantly among size classes, with larger individuals consuming more scales and larger items, especially odonatans and ephemeropterans. Scale consumption was not significantly different between dry and wet seasons. Roeboides affinis incorporated some food items into the diet as a response to the impoundment, like other species. Scale consumption was higher in lotic sites, refuting our initial hypothesis, what suggests that the lepidophagous habit is related the rheophilic nature of R. affinis.Caracterizamos o consumo de escamas e outros recursos alimentares por Roeboides affinis, um lepidófago facultativo, no alto rio Tocantins, na região represada pela Usina Hidrelétrica de Serra da Mesa. A dieta foi avaliada em relação a classes de tamanho, estações chuvosa e seca, e entre locais com características distintas de fluxo d'água (lótico vs. lêntico relacionadas com a distância da barragem e fase de desenvolvimento do reservatório. Com o aumento da abundância de peixes e da transparência da água após o represamento, esperamos um maior consumo de escamas nos locais lênticos. Da mesma forma, na época seca

Closure plan for the M-Area settling basin and vicinity at the Savannah River Plant

International Nuclear Information System (INIS)

Colven, W.P.; Pickett, J.B.

1985-07-01

The areas addressed in this closure plan include a process sewer line, surface impoundment (settling basin), overflow ditch, seepage area, and a Carolina Bay known as Lost Lake. Since it is proposed that the basin and vicinity be closed with the hazardous wastes placed and stabilized in the basin, it will be closed pursuant to regulations for closing a hazardous waste landfill. No free liquids will remain in the impoundment after closure is completed

Nonlinear optical techniques for surface studies

International Nuclear Information System (INIS)

Shen, Y.R.

1981-09-01

Recent effort in developing nonlinear optical techniques for surface studies is reviewed. Emphasis is on monolayer detection of adsorbed molecules on surfaces. It is shown that surface coherent antiStokes Raman scattering (CARS) with picosecond pulses has the sensitivity of detecting submonolayer of molecules. On the other hand, second harmonic or sum-frequency generation is also sensitive enough to detect molecular monolayers. Surface-enhanced nonlinear optical effects on some rough metal surfaces have been observed. This facilitates the detection of molecular monolayers on such surfaces, and makes the study of molecular adsorption at a liquid-metal interface feasible. Advantages and disadvantages of the nonlinear optical techniques for surface studies are discussed

Mirror reactor surface study

Energy Technology Data Exchange (ETDEWEB)

Hunt, A. L.; Damm, C. C.; Futch, A. H.; Hiskes, J. R.; Meisenheimer, R. G.; Moir, R. W.; Simonen, T. C.; Stallard, B. W.; Taylor, C. E.

1976-09-01

A general survey is presented of surface-related phenomena associated with the following mirror reactor elements: plasma first wall, ion sources, neutral beams, director converters, vacuum systems, and plasma diagnostics. A discussion of surface phenomena in possible abnormal reactor operation is included. Several studies which appear to merit immediate attention and which are essential to the development of mirror reactors are abstracted from the list of recommended areas for surface work. The appendix contains a discussion of the fundamentals of particle/surface interactions. The interactions surveyed are backscattering, thermal desorption, sputtering, diffusion, particle ranges in solids, and surface spectroscopic methods. A bibliography lists references in a number of categories pertinent to mirror reactors. Several complete published and unpublished reports on surface aspects of current mirror plasma experiments and reactor developments are also included.

Mirror reactor surface study

International Nuclear Information System (INIS)

Hunt, A.L.; Damm, C.C.; Futch, A.H.; Hiskes, J.R.; Meisenheimer, R.G.; Moir, R.W.; Simonen, T.C.; Stallard, B.W.; Taylor, C.E.

1976-01-01

A general survey is presented of surface-related phenomena associated with the following mirror reactor elements: plasma first wall, ion sources, neutral beams, director converters, vacuum systems, and plasma diagnostics. A discussion of surface phenomena in possible abnormal reactor operation is included. Several studies which appear to merit immediate attention and which are essential to the development of mirror reactors are abstracted from the list of recommended areas for surface work. The appendix contains a discussion of the fundamentals of particle/surface interactions. The interactions surveyed are backscattering, thermal desorption, sputtering, diffusion, particle ranges in solids, and surface spectroscopic methods. A bibliography lists references in a number of categories pertinent to mirror reactors. Several complete published and unpublished reports on surface aspects of current mirror plasma experiments and reactor developments are also included

40 CFR 421.11 - Specialized definitions.

Science.gov (United States)

2010-07-01

... pond water surface area for the purpose of calculating the volume of waste water shall mean the area within the impoundment for rainfall and the actual water surface area for evaporation. [39 FR 12825, Apr...

Site Study Plan for laboratory soil mechanics, Deaf Smith County site, Texas: Revision 1

International Nuclear Information System (INIS)

1987-12-01

This Site Study Plan for laboratory soil mechanics describes the laboratory testing to be conducted on soil samples collected as part of the characterization of the Deaf Smith County site, Texas. This study provides for measurements of index, mechanical, thermal, hydrologic, chemical, and mineral properties of soils from boring throughout the site. Samples will be taken from Playa Borings/Trenching, Transportation/Utilities Foundation Borings, Repository Surface Facilities Design Foundation Borings, and Exploratory Shaft Facilities Design Foundation Borings. Data from the laboratory tests will be used for soil strata characterization, design of foundations for surface structures, design of transportation facilities and utility structures, design of impoundments, design of shaft lining, design of the shaft freeze wall, shaft permitting, performance assessment calculations, and other program requirements. A tentative testing schedule and milestone log are given. A quality assurance program will be utilized to assure that activities affecting quality are performed correctly and that appropriate documentation is maintained. 18 refs., 6 figs., 3 tabs

Consolidation of tailings

International Nuclear Information System (INIS)

Nelson, J.D.; Wardwell, R.E.; Abt, S.R.; Staub, W.P.

1983-09-01

The integrity of cover systems placed on tailings impoundments will be affected by the potential for differential settlement of the tailings surface. Settlement of the sand fraction will occur relatively rapidly. The slimes will take longer time for consolidation and will produce greater settlement. This report reviews the phenomenon of consolidation for saturated and unsaturated tailings. The effect of load application by cover placement and the extent to which dewatering of tailings will cause consolidation are considered. In addition, the feasibility of inducing consolidation by alternative means and the potential applicability of these methods to tailings impoundments reclamation are discussed. Differential settlement of the tailings will cause tensile strain to be developed in covers. This strain could be large enough to cause cracking within a relatively brittle compacted clay. Dewatering of tailings by drainage can cause settlement even greater than that by placement of a cover material. Dewatering of the tailings would also increase the stability of the tailings surface, thereby enhancing reclamation operations. Consequently, in view of the enhanced surface stability and the fact that a portion of the differential settlement can be accomplished prior to cover placement, dewatering of tailings impoundments during operations may have benefical effects

40 CFR 63.134 - Process wastewater provisions-surface impoundments.

Science.gov (United States)

2010-07-01

..., and semi-annually thereafter, for improper work practices and control equipment failures in accordance... this subpart, when an improper work practice or a control equipment failure is identified, first... treats a Group 1 wastewater stream or a residual removed from a Group 1 wastewater stream, the owner or...

Interfacial stability of soil covers on lined surface impoundments

International Nuclear Information System (INIS)

Mitchell, D.H.; Gates, T.E.

1986-04-01

The factors affecting the interfacial stability of soil covers on geomembranes were examined to determine the maximum stable slopes for soil cover/geomembrane systems. Several instances of instability of soil covers on geomembranes have occurred at tailings ponds, leaving exposed geomembranes with the potential for physical ddamage and possibly chemical and ultraviolet degradation. From an operator's viewpoint, it is desirable to maximize the slope of lined facilities in order to maximize the volume-to-area ratio; however, the likelihood for instability also increases with increasing slope. Frictional data obtained from direct shear tests are compared with stability data obtained using a nine-square-meter (m 2 ) engineering-scale test stand to verify that direct shear test data are valid in slope design calculations. Interfacial frictional data from direct shear tests using high-density polyethylene and a poorly graded sand cover agree within several degrees with the engineering-scale tests. Additional tests with other soils and geomembranes are planned. The instability of soil covers is not always an interfacial problem; soil erosion and limited drainage capacity are additional factors that must be considered in the design of covered slopes. 7 refs., 5 figs., 2 tabs

Estimating the Creation and Removal Date of Fracking Ponds Using Trend Analysis of Landsat Imagery

Science.gov (United States)

Platt, Rutherford V.; Manthos, David; Amos, John

2018-02-01

Hydraulic fracturing, or fracking, is a process of introducing liquid at high pressure to create fractures in shale rock formations, thus releasing natural gas. Flowback and produced water from fracking operations is typically stored in temporary open-air earthen impoundments, or frack ponds. Unfortunately, in the United States there is no public record of the location of impoundments, or the dates that impoundments are created or removed. In this study we use a dataset of drilling-related impoundments in Pennsylvania identified through the FrackFinder project led by SkyTruth, an environmental non-profit. For each impoundment location, we compiled all low cloud Landsat imagery from 2000 to 2016 and created a monthly time series for three bands: red, near-infrared (NIR), and the Normalized Difference Vegetation Index (NDVI). We identified the approximate date of creation and removal of impoundments from sudden breaks in the time series. To verify our method, we compared the results to date ranges derived from photointerpretation of all available historical imagery on Google Earth for a subset of impoundments. Based on our analysis, we found that the number of impoundments built annually increased rapidly from 2006 to 2010, and then slowed from 2010 to 2013. Since newer impoundments tend to be larger, however, the total impoundment area has continued to increase. The methods described in this study would be appropriate for finding the creation and removal date of a variety of industrial land use changes at known locations.

Influence of vegetation and sewage sludge on sealing layer of fly ashes in post-treatment of mine tailings impoundments; Inverkan av vegetation och roetslam paa taetskikt av flygaska vid efterbehandling av sandmagasin

Energy Technology Data Exchange (ETDEWEB)

Greger, Maria; Neuschuetz, Clara (Inst. of Bothany, Stockholm Univ., Stockholm (Sweden)); Isaksson, Karl-Erik (Boliden Mineral AB, Stockholm (Sweden))

2009-03-15

Mining industry produces 25 Mton mine tailings yearly that are deposited in impoundments in the nature. When this sand, containing sulphur rich minerals, reacts with oxygen and water it starts to weather and acidic metal rich water is formed. To prevent this, the sand can be covered with a sealing layer and a protective cover layer with vegetation. As sealing and cover materials fly ashes and sewage sludge can be used. The aim of this investigation was to find out: 1) how sealing layer of fly ashes with and without sewage sludge, and a cover with sewage sludge can be placed practically on mine tailings in a cold climate. 2) how such a cover should be constructed to minimize the risk of root penetration and leakage of nutrients and metals 3) which vegetation that is most suitable This was investigated in field- and greenhouse tests with a sealing layer of fly ash and/or sewage sludge with a cover layer of sewage sludge in which different plant species were established. The practical application was performed in 0.3-1 ha plots at a mine tailings impoundments at Boliden. The ability of plant roots to penetrate a sealing layer was investigated, as well as the effect of simulated root exudates on the penetration resistance in hardened ash. Leakage of nutrients and metals from cover layer of sewage sludge, in some cases with sealing layers beneath, was investigated in field and greenhouse lysimeters. Various plant species were compared on their ability to affect metal and nutrient leakage as well as root penetration and shattering of the hardened ashes. The project was a cooperation between Stockholm University and Boliden Mineral AB, and the field tests were performed at the impoundment Gillervattnet in Boliden and in Garpenberg. Cooperating were also Iggesund Paperboard, Skellefteaa Kraft, Stora Enso Fors, Umeaa Energi and Vattenfall, all producers of ashes that were used, as well as Stockholm Vatten AB, which produced the sewage sludge. The most important conclusions

Analysis of the behaviour of embankment dams during and after impoundment; Analyse du comportement de barrages en remblai pendant et apres leur mise en eau

Energy Technology Data Exchange (ETDEWEB)

Massiera, M. [Moncton Univ., Moncton, NB (Canada). Dept. of Civil Engineering; Szostak-Chrzanowski, A; Bazanowski, M. [New Brunswick Univ., Fredericton, NB (Canada). Canadian Centre for Geodetic Engineering; Withaker, C. [Metropolitan Water District of Southern California MWD, Glendora, CA (United States)

2009-07-01

This paper analyzed the behaviour of 2 embankment dams during impoundment. The study compared the values of the observed and calculated displacements of the crest during the initial filling of the reservoirs at the zoned earth West Dam in California and the Tounustouc concrete face rockfill dam (CFRD) in Quebec. The calculations were performed using finite element analysis. Rock and earthfill dams constructed on moraine deposits are known to deform under the influence of water load as the reservoir is filled. Therefore, this study also analyzed the long term deformations of the West Dam during 4 subsequent years of operation of the reservoir. Modelling rock and earthfill dams takes into account the nonlinear behaviour of the construction materials; interaction between the structure and the underlying soil and rock strata; influence of water load on the structure and on the foundation bedrock; and the effects of water saturation. This paper showed that geotechnical and geodetic monitoring may provide a warning system in case of abnormal behaviour of the embankment dam. In tectonically active zones, monitoring surveys may also provide information on the effects of seismic disturbances. 18 refs., 11 figs.

Seismic hazard assessment of the Three Gorges Project

Directory of Open Access Journals (Sweden)

Yao Yunsheng

2013-05-01

Full Text Available Seismic monitoring data for the past 50 years in the Three Gorges Reservoir area show that the reservoir head area is a typical weak seismic region with low seismicity before impoundment and that the epicenters were concentrated in the east and west sides of the Zigui Basin, most of which were natural tectonic earthquakes. After impoundment, the seismic activity shifted to the segment between Badong and Zigui along the Yangtze River, mainly within 5 km of the reservoir bank. The seismogenesis was categorized into four types; Karst collapse earthquakes, earthquakes caused by Karst gas explosion, mining tunnel collapse earthquakes, and rock (terrane slip earthquakes, all of which are related to the lithology, structure, and tectonics of near-surface geological bodies of the area. Compared with the seismicity before impoundment, the seismic frequency increase was remarkable, with most of the magnitudes below Ms2. 0. Therefore, the intensity of the earthquakes remained at a low level. On November 22, 2008, a magnitude 4. 1 earthquake, the largest earthquake recorded since impoundment, occurred in Quyuan Town, Zigui County. The intensity and PGA of reservoir-induced earthquakes are higher than those of tectonic earthquakes with equal magnitude, but the peak intensity of reservoir-induced earthquakes is not likely to go beyond that of the estimated range from earlier studies.

Screening Assessment of Radionuclide Migration in Groundwater from the “Dneprovskoe” Tailings Impoundment (Dneprodzerzhynsk City) and Evaluation of Remedial Options

Energy Technology Data Exchange (ETDEWEB)

Skalskyi, O.; Bugai, D. [Institute of Geological Sciences, National Academy of Sciences of Ukraine (Ukraine); Ryazantsev, V. [State Nuclear Regularity Committee of Ukraine, Kiev (Ukraine)

2014-05-15

The paper presents results of mathematical modeling of the hydrogeological conditions at the “Dneprovskoe” (“D”) tailings impoundment –object of the former industrial association of “Pridneprovsky Chemical Plant”, which contains uranium ore processing wastes. This radioactively polluted site is located in a densely populated region (at the outskirts of Dneprodzerginsk City) near the major watercourse of the Ukraine — Dnieper River.The mathematical modeling utilized Visual Modflow (for groundwater flow) and Ecolego (Facilia AB, Sweden) radioecology modeling software (for radionuclide transport).Modeling results indicate the possibility of essential radioactive contamination in future of the phreatic aquifer in alluvial deposits between the “D” tailings and the Dnieper River (mainly due to migration of uranium). Therefore long-term management strategies should preclude water usage from the aquifer in the zone of the in-fluence of the “D” tailings. Filtration discharge of uranium to the Dnepr River does not represent a significant risk due to large dilution by surface waters. The important modeling conclusion is that besides the uranium ore processing wastes inside the tailings, the major source of radionuclide migration to groundwater is represented by contaminated geological deposits below the tailings. This last source was formed due to leakage of wastewaters during the operational period of the “D” tailings (1954–1968). Therefore an exemption and re-disposal of wastes from the “D” tailings to a more safe storage location (proposed by some remedial plans) will not provide significant benefit from the viewpoint of minimizing of radionuclide transport to the groundwater and Dnieper River (especially in short-and medium-term perspective). The rational remedial strategy for the “D” tailings is conservation of tailing wastes in-situ by means of specially designed “zero flux” soil screen, which would minimize infiltration of

Surface and subsurface soils at the Pond B dam: July 1998

International Nuclear Information System (INIS)

Halverson, N.V.

1999-01-01

Pond B, 685-13G, is an inactive reactor cooling impoundment built in 1961 on the Savannah River Site (SRS). Between 1961 and 1964, Pond B received R-Reactor cooling water discharges that were contaminated with 137 Cs, 90 Sr and plutonium. Though the pond has not been used since 1964, radionuclides from the contaminated cooling water remain in the water and in the surface sediments of the pond. The current proposal to fix and repair the Pond B dam structure includes installing a new drain system and monitoring equipment. The dam will be reinforced with additional previous material on the downstream face of the dam. The objectives of this report are to describe the sampling methodology used during the July 1998 sampling event at the downstream face of the Pond B dam and in Pond B, present the results of the sampling event, and compare, where possible, these results to related risk-based standards

Assessment of the underground disposal of tailings

Energy Technology Data Exchange (ETDEWEB)

Hutt, N M [Morwijk Enterprises Ltd., (Canada); Morin, K A [Normar Enterprises, (Canada)

1995-06-01

The Atomic Energy Control Board (AECB) of Canada is facing the issue of long-term disposal of uranium tailings. One option that has not been examined in sufficient detail for the AECB is the retrieval of tailings from surface impoundments and subsequent placement of those tailings in underground workings of mines. This report is structured like a catalogue of facts and information, with each paragraph presenting some concept, concern, theory, or case study involving the retrieval or placement of tailings. All relevant information, findings, interpretations, conclusions, and recommendations gathered during the course of this study are included. The Table of Contents illustrates the striking number of relevant topics and acts like a flowchart or checklist to ensure that an underground-disposal submission by a mining company has addressed relevant topics. This report explains in detail the implications of disturbing surface-impounded tailings for the purpose of placing only some of the volume underground. The cumulative environmental, safety, and monetary liabilities of such a partial scheme can be discouraging in some cases. (author). 244 refs., 47 tabs., 17 figs.

Assessment of the underground disposal of tailings

International Nuclear Information System (INIS)

Hutt, N.M.; Morin, K.A.

1995-06-01

The Atomic Energy Control Board (AECB) of Canada is facing the issue of long-term disposal of uranium tailings. One option that has not been examined in sufficient detail for the AECB is the retrieval of tailings from surface impoundments and subsequent placement of those tailings in underground workings of mines. This report is structured like a catalogue of facts and information, with each paragraph presenting some concept, concern, theory, or case study involving the retrieval or placement of tailings. All relevant information, findings, interpretations, conclusions, and recommendations gathered during the course of this study are included. The Table of Contents illustrates the striking number of relevant topics and acts like a flowchart or checklist to ensure that an underground-disposal submission by a mining company has addressed relevant topics. This report explains in detail the implications of disturbing surface-impounded tailings for the purpose of placing only some of the volume underground. The cumulative environmental, safety, and monetary liabilities of such a partial scheme can be discouraging in some cases. (author). 244 refs., 47 tabs., 17 figs

Historic mills and mill tailings as potential sources of contamination in and near the Humboldt River basin, northern Nevada. Chapter D.

Science.gov (United States)

Nash, J. Thomas; Stillings, Lisa L.

2003-01-01

Reconnaissance field studies of 40 mining districts in and near the Humboldt River basin have identified 83 mills and associated tailings impoundments and several other kinds of mineral-processing facilities (smelters, mercury retorts, heap-leach pads) related to historic mining. The majority of the mills and tailings sites are not recorded in the literature. All tailings impoundments show evidence of substantial amounts of erosion. At least 11 tailings dams were breached by flood waters, carrying fluvial tailings 1 to 15 km down canyons and across alluvial fans. Most of the tailings sites are dry most of the year, but some are near streams. Tailings that are wet for part of the year do not appear to be reacting significantly with those waters because physical factors such as clay layers and hard-pan cement appear to limit permeability and release of metals to surface waters. The major impact of mill tailings on surface- water quality may be brief flushes of runoff during storm events that carry acid and metals released from soluble mineral crusts. Small ephemeral ponds and puddles that tend to collect in trenches and low areas on tailings impoundments tend to be acidic and extremely enriched in metals, in part through cycles of evaporation. Ponded water that is rich in salts and metals could be acutely toxic to unsuspecting animals. Rare extreme storms have the potential to cause catastrophic failure of tailings impoundments, carry away metals in stormwaters, and transport tailings as debris flows for 1 to 15 km. In most situations these stormwaters and transported tailings could impact wildlife but probably would impact few or no people or domes-tic water wells. Because all identified historic tailings sites are several kilometers or more from the Humboldt River and major tributaries, tailings probably have no measurable impact on water quality in the main stem of the Humboldt River.

Prevalence of gastrointestinal parasites of stray dogs impounded by the Society for the Prevention of Cruelty to Animals (SPCA), Durban and Coast, South Africa.

Science.gov (United States)

Mukaratirwa, S; Singh, V P

2010-06-01

Coprological examination was used to determine the prevalence and intensity of gastrointestinal parasites of stray dogs impounded by the Society for the Prevention of Cruelty to Animals (SPCA), Durban and Coast, South Africa. Helminth and protozoan parasites were found in faeces of 240 dogs with an overall prevalence of 82.5% (helminth parasites 93.1% and protozoan parasites 6.9%). The following parasites and their prevalences were detected; Ancylostoma sp. (53.8%), Trichuris vulpis (7.9%), Spirocerca lupi (5.4%), Toxocara canis (7.9%), Toxascaris leonina (0.4%) Giardia intestinalis (5.6%) and Isospora sp. (1.3%). Dogs harbouring a single parasite species were more common (41.7%) than those harbouring 2 (15%) or multiple (2.1%) species. Ancylostoma sp., Toxocara canis and Giardia intestinalis have zoonotic potential and were detected in 66.7% of the samples.

Surface hydrologic characteristics of proposed repository locations in the Palo Duro Basin of the Texas Panhandle

International Nuclear Information System (INIS)

1985-04-01

This report provides a description of the surface hydrology in the two proposed locations of a high-level waste repository within the Palo Duro Basin of the Texas Panhandle. Included for consideration are the topography; the major drainage systems - Palo Duro, Tierra Blanca, and Tule Creeks, and Prairie Dog Town Fork of the Red River; and the most prominent impoundments, the playa lakes. The magnitude and frequency of precipitation throughout the region are discussed, and rainfall depth-duration-area data for the 100-year, 500-year, and probable maximum storms are presented. Soil properties are also described, with specific reference to the infiltration and runoff processes and the contribution of these processes to Ogallala aquifer recharge. A summary discussion of the local streams includes information on historical streamflow, a brief description of flooding, and results of a study of floodplains for the 100-year, 500-year, and probable maximum storms. The report concludes with a characterization of the water quality of these streams and an explanation of the local geologic influences on stream-water chemistry. 25 figures, 20 tables

Automated detection of submerged navigational obstructions in freshwater impoundments with hull mounted sidescan sonar

Science.gov (United States)

Morris, Phillip A.

The prevalence of low-cost side scanning sonar systems mounted on small recreational vessels has created improved opportunities to identify and map submerged navigational hazards in freshwater impoundments. However, these economical sensors also present unique challenges for automated techniques. This research explores related literature in automated sonar imagery processing and mapping technology, proposes and implements a framework derived from these sources, and evaluates the approach with video collected from a recreational grade sonar system. Image analysis techniques including optical character recognition and an unsupervised computer automated detection (CAD) algorithm are employed to extract the transducer GPS coordinates and slant range distance of objects protruding from the lake bottom. The retrieved information is formatted for inclusion into a spatial mapping model. Specific attributes of the sonar sensors are modeled such that probability profiles may be projected onto a three dimensional gridded map. These profiles are computed from multiple points of view as sonar traces crisscross or come near each other. As lake levels fluctuate over time so do the elevation points of view. With each sonar record, the probability of a hazard existing at certain elevations at the respective grid points is updated with Bayesian mechanics. As reinforcing data is collected, the confidence of the map improves. Given a lake's current elevation and a vessel draft, a final generated map can identify areas of the lake that have a high probability of containing hazards that threaten navigation. The approach is implemented in C/C++ utilizing OpenCV, Tesseract OCR, and QGIS open source software and evaluated in a designated test area at Lake Lavon, Collin County, Texas.

Site characterization design and techniques used at the Southern Shipbuilding Corporation site

International Nuclear Information System (INIS)

Mueller, J.P.; Geraghty, C.A.; Moore, G.W.; Mullins, J.R.

1995-01-01

The Southern Shipbuilding Corporation (SSC) site is an inactive barge/ship manufacturing and repair facility situated on approximately 54 acres in Slidell, St. Tammany Parish, Louisiana. Two unlined surface impoundments (North and South impoundments) are situated on the northwest portion of the site and are surrounded on three sides by Bayou Bonfouca. These impoundments are the sources of carcinogenic polynuclear aromatic hydrocarbon (CPAH) contamination at the site. Inadequate containment has resulted in the release of impoundment wastes into the bayou. To evaluate potential response alternatives for the site, an Engineering Evaluation/Cost Analysis (EE/CA) field investigation was conducted from July through October 1994. A two phase sampling approach was used in combination with innovative and traditional sampling techniques, field screening technologies, and exploitation of the visual characteristics of the waste to determine the extent of waste migration with limited off-site laboratory confirmation. A skid-mounted mobile drilling unit, secured to a specialized sampling platform designed for multiple applications, was used for collection of sediment cores from the bayou as well as tarry sludge cores from the impoundments. Field screening of core samples was accomplished on site using an organic vapor analyzer and a total petroleum hydrocarbon (TPH) field analyzer. Pollutants of concern include metals, cyanide, dioxin, and organic compounds. This paper presents details on the sampling design and characterization techniques used to accomplish the EE/CA field investigation

Restoring tides to reduce methane emissions in impounded wetlands: A new and potent Blue Carbon climate change intervention.

Science.gov (United States)

Kroeger, Kevin D; Crooks, Stephen; Moseman-Valtierra, Serena; Tang, Jianwu

2017-09-20

Coastal wetlands are sites of rapid carbon (C) sequestration and contain large soil C stocks. Thus, there is increasing interest in those ecosystems as sites for anthropogenic greenhouse gas emission offset projects (sometimes referred to as "Blue Carbon"), through preservation of existing C stocks or creation of new wetlands to increase future sequestration. Here we show that in the globally-widespread occurrence of diked, impounded, drained and tidally-restricted salt marshes, substantial methane (CH 4 ) and CO 2 emission reductions can be achieved through restoration of disconnected saline tidal flows. Modeled climatic forcing indicates that tidal restoration to reduce emissions has a much greater impact per unit area than wetland creation or conservation to enhance sequestration. Given that GHG emissions in tidally-restricted, degraded wetlands are caused by human activity, they are anthropogenic emissions, and reducing them will have an effect on climate that is equivalent to reduced emission of an equal quantity of fossil fuel GHG. Thus, as a landuse-based climate change intervention, reducing CH 4 emissions is an entirely distinct concept from biological C sequestration projects to enhance C storage in forest or wetland biomass or soil, and will not suffer from the non-permanence risk that stored C will be returned to the atmosphere.

Restoring tides to reduce methane emissions in impounded wetlands: A new and potent Blue Carbon climate change intervention

Science.gov (United States)

Kroeger, Kevin D.; Crooks, Stephen; Moseman-Valtierra, Serena; Tang, Jianwu

2017-01-01

Coastal wetlands are sites of rapid carbon (C) sequestration and contain large soil C stocks. Thus, there is increasing interest in those ecosystems as sites for anthropogenic greenhouse gas emission offset projects (sometimes referred to as “Blue Carbon”), through preservation of existing C stocks or creation of new wetlands to increase future sequestration. Here we show that in the globally-widespread occurrence of diked, impounded, drained and tidally-restricted salt marshes, substantial methane (CH4) and CO2 emission reductions can be achieved through restoration of disconnected saline tidal flows. Modeled climatic forcing indicates that tidal restoration to reduce emissions has a much greater impact per unit area than wetland creation or conservation to enhance sequestration. Given that GHG emissions in tidally-restricted, degraded wetlands are caused by human activity, they are anthropogenic emissions, and reducing them will have an effect on climate that is equivalent to reduced emission of an equal quantity of fossil fuel GHG. Thus, as a landuse-based climate change intervention, reducing CH4 emissions is an entirely distinct concept from biological C sequestration projects to enhance C storage in forest or wetland biomass or soil, and will not suffer from the non-permanence risk that stored C will be returned to the atmosphere.

40 CFR 265.1 - Purpose, scope, and applicability.

Science.gov (United States)

2010-07-01

... issued under the Marine Protection, Research, and Sanctuaries Act; [Comment: These part 265 regulations... wastewater treatment sludge is generated in a surface impoundment as part of the plant's wastewater treatment...

A systematic first-principles study of surface energies, surface relaxation and Friedel oscillation of magnesium surfaces

International Nuclear Information System (INIS)

Tang, Jia-Jun; Yang, Xiao-Bao; Zhao, Yu-Jun; OuYang, LiuZhang; Zhu, Min

2014-01-01

We systematically study the surface energies and surface relaxations of various low-index and high-index Mg surfaces. It is found that low-index surfaces are not necessarily stable as Mg(1 0  1-bar  0) is the most unstable surface in the series of Mg(1 0  1-bar  n) (n = 0–9). A surface-energy predicting model based on the bond cutting is proposed to explain the relative surface stabilities. The local relaxations of the low-index surfaces could be explained by the Friedel oscillation. For the high-index surfaces, the combination of charge smoothing effect and dramatic charge depletion influences the relaxations, which show a big difference from the low-index ones. Our findings provide theoretical data for considerable insights into the surface energies of hexagonal close-packed metals. (paper)

Impacts of boreal hydroelectric reservoirs on seasonal climate and precipitation recycling as simulated by the CRCM5: a case study of the La Grande River watershed, Canada

Science.gov (United States)

Irambona, C.; Music, B.; Nadeau, D. F.; Mahdi, T. F.; Strachan, I. B.

2018-02-01

Located in northern Quebec, Canada, eight hydroelectric reservoirs of a 9782-km2 maximal area cover 6.4% of the La Grande watershed. This study investigates the changes brought by the impoundment of these reservoirs on seasonal climate and precipitation recycling. Two 30-year climate simulations, corresponding to pre- and post-impoundment conditions, were used. They were generated with the fifth-generation Canadian Regional Climate Model (CRCM5), fully coupled to a 1D lake model (FLake). Seasonal temperatures and annual energy budget were generally well reproduced by the model, except in spring when a cold bias, probably related to the overestimation of snow cover, was seen. The difference in 2-m temperature shows that reservoirs induce localized warming in winter (+0.7 ± 0.02 °C) and cooling in the summer (-0.3 ± 0.02 °C). The available energy at the surface increases throughout the year, mostly due to a decrease in surface albedo. Fall latent and sensible heat fluxes are enhanced due to additional energy storage and availability in summer and spring. The changes in precipitation and runoff are within the model internal variability. At the watershed scale, reservoirs induce an additional evaporation of only 5.9 mm year-1 (2%). We use Brubaker's precipitation recycling model to estimate how much of the precipitation is recycled within the watershed. In both simulations, the maximal precipitation recycling occurs in July (less than 6%), indicating weak land-atmosphere coupling. Reservoirs do not seem to affect this coupling, as precipitation recycling only decreased by 0.6% in July.

Liners and Leak Detection Systems for Hazardous Waste Land Disposal Units - Federal Register Notice, January 29, 1992

Science.gov (United States)

The EPA is amending its current regulations under the Resource Conservation and Recovery Act (RCRA) concerning liner and leachate collection and removal systems for hazardous waste surface impoundments, landfills, and waste piles.

Wetting study of patterned surfaces for superhydrophobicity

Energy Technology Data Exchange (ETDEWEB)

Bhushan, Bharat [Nanotribology Laboratory for Information Storage and MEMS/NEMS (NLIM), 201 W. 19th Avenue, Ohio State University, Columbus, OH 43202-1107 (United States)], E-mail: Bhushan.2@osu.edu; Jung, Yong Chae [Nanotribology Laboratory for Information Storage and MEMS/NEMS (NLIM), 201 W. 19th Avenue, Ohio State University, Columbus, OH 43202-1107 (United States)

2007-10-15

Superhydrophobic surfaces have considerable technological potential for various applications due to their extreme water-repellent properties. A number of studies have been carried out to produce artificial biomimetic roughness-induced hydrophobic surfaces. In general, both homogeneous and composite interfaces are possible on the produced surface. Silicon surfaces patterned with pillars of two different diameters and heights with varying pitch values were fabricated. We show how static contact angles vary with different pitch values on the patterned silicon surfaces. Based on the experimental data and a numerical model, the trends are explained. We show that superhydrophobic surfaces have low hysteresis and tilt angle. Tribological properties play an important role in many applications requiring water-repellent properties. Therefore, it is important to study the adhesion and friction properties of these surfaces that mimic nature. An atomic/friction force microscope (AFM/FFM) is used for surface characterization and adhesion and friction measurements.

75 FR 5076 - American Hydro Power, Inc.; Notice of Preliminary Permit Application Accepted for Filing and...

Science.gov (United States)

2010-02-01

..., 346-foot-long Diamond Mills Dam; (2) an existing 140-acre impoundment with a normal water surface... the feasibility of the Diamond Mills Dam Hydroelectric Project No. 13587, to be located on Esopus...

Predictive geochemical modeling of contaminant concentrations in laboratory columns and in plumes migrating from uranium mill tailings waste impoundments

International Nuclear Information System (INIS)

Peterson, S.R.; Martin, W.J.; Serne, R.J.

1986-04-01

A computer-based conceptual chemical model was applied to predict contaminant concentrations in plumes migrating from a uranium mill tailings waste impoundment. The solids chosen for inclusion in the conceptual model were selected based on reviews of the literature, on ion speciation/solubility calculations performed on the column effluent solutions and on mineralogical characterization of the contacted and uncontacted sediments. The mechanism of adsorption included in the conceptual chemical model was chosen based on results from semiselective extraction experiments and from mineralogical characterization procedures performed on the sediments. This conceptual chemical model was further developed and partially validated in laboratory experiments where assorted acidic uranium mill tailings solutions percolated through various sediments. This document contains the results of a partial field and laboratory validation (i.e., test of coherence) of this chemical model. Macro constituents (e.g., Ca, SO 4 , Al, Fe, and Mn) of the tailings solution were predicted closely by considering their concentrations to be controlled by the precipitation/dissolution of solid phases. Trace elements, however, were generally predicted to be undersaturated with respect to plausible solid phase controls. The concentration of several of the trace elements were closely predicted by considering their concentrations to be controlled by adsorption onto the amorphous iron oxyhydroxides that precipitated

Prevalence of gastrointestinal parasites of stray dogs impounded by the Society for the Prevention of Cruelty to Animals (SPCA, Durban and Coast, South Africa : short communication

Directory of Open Access Journals (Sweden)

S. Mukaratirwa

2010-05-01

Full Text Available Coprological examination was used to determine the prevalence and intensity of gastrointestinal parasites of stray dogs impounded by the Society for the Prevention of Cruelty to Animals (SPCA, Durban and Coast, South Africa. Helminth and protozoan parasites were found in faeces of 240 dogs with an overall prevalence of 82.5% (helminth parasites 93.1% and protozoan parasites 6.9 %. The following parasites and their prevalences were detected; Ancylostoma sp. (53.8 %, Trichuris vulpis (7.9 %, Spirocerca lupi (5.4 %, Toxocara canis (7.9 %, Toxascaris leonina (0.4 % Giardia intestinalis (5.6 % and Isospora sp. (1.3 %. Dogs harbouring a single parasite species were more common (41.7 % than those harbouring 2 (15 % or multiple (2.1 % species. Ancylostoma sp., Toxocara canis and Giardia intestinalis have zoonotic potential and were detected in 66.7 % of the samples.

Surface studies with high-energy ion beams

Energy Technology Data Exchange (ETDEWEB)

Stensgaard, Ivan [Aarhus Univ. (Denmark). Inst. of Physics

1992-07-01

High-energy ion scattering is an extremely useful technique for surface studies. Three methods for surface composition analysis (Rutherford backscattering, nuclear-reaction analysis and elastic recoil detection) are discussed. Directional effects in ion-beam surface interactions (shadowing and blocking) form the basis for surface structure analysis with high-energy ion beams and these phenomena are addressed in some detail. It is shown how surface relaxation and reconstruction, as well as positions of adsorbed atoms, can be determined by comparison with computer simulations. A special technique called transmission channelling is introduced and shown to be particularly well suited for studies of adsorption positions, even of hydrogen. Recent developments in the field are demonstrated by discussing a large number of important (experimental) applications which also include surface dynamics and melting, as well as epitaxy and interface structure. (author).

A pulsed source neutron reflectometer for surface studies

International Nuclear Information System (INIS)

Penfold, J.; Williams, W.G.

1985-05-01

A design for a neutron reflectometer for surface studies to be constructed at the SNS is presented. Examples of its use to study problems in surface chemistry, surface magnetism and low dimensional structures are highlighted. (author)

Energy loss spectroscopy applied to surface studies

International Nuclear Information System (INIS)

Lecante, J.

1975-01-01

The analysis of energy losses suffered by slow electrons (5eV to 300eV) back-scattered by single crystal surfaces appears to be a powerful method for surfaces studies. The inelastic scattering of these slow electrons limits their escape depth to the surface region. After a review of the basic excitation processes due to the interaction between electrons and surfaces (phonons, plasmons and electronic transitions) a brief discussion is given about the instruments needed for this electrons spectroscopy. Finally some experimental results are listed and it is shown that the comparison of the results given by ELS with other surface sensitive methods such as UPS is very fruitful and new information can be obtained. The improvement of theoretical studies on surface excitations due to slow electrons will provide in the next future the possibility of analysing in a more quantitative way the results given by ELS [fr

Synchrotron x-ray diffraction study of liquid surfaces

DEFF Research Database (Denmark)

Als-Nielsen, Jens Aage; Pershan, P.S.

1983-01-01

A spectrometer for X-ray diffraction and refraction studies of horizontal, free surfaces of liquids is described. As an illustration smetic-A layering at the surface of a liquid crystal is presented.......A spectrometer for X-ray diffraction and refraction studies of horizontal, free surfaces of liquids is described. As an illustration smetic-A layering at the surface of a liquid crystal is presented....

(AJST) HYDROBIOLOGICAL STUDIES ON IBIEKUMA RIVER AT ...

African Journals Online (AJOL)

opiyo

. NIGERIA, AFTER IMPOUNDMENT: THE FAUNAL CHARACTERISTICS. Clement Aghatise Edokpayi* and Ekikhalo Catherine Osimen**. *Department of Zoology, Marine Biology and Fisheries,. University of Lagos, Akoka, Lagos, Nigeria.

Surface study of fusion research in universities linkage organization

International Nuclear Information System (INIS)

Miyahara, Akira.

1980-04-01

The surface studies for nuclear fusion research consist of the studies on the surface process and the surface damage. The problems with the surface study are different at different research stages. The plasma-wall interaction in the ignition stage is mainly concerned with heating. The impurity control becomes important in the breakeven stage. In the longer burn experiment, the problems of plasma contamination and ash accumulation are serious, and the blistering is also a problem. From the reactor aspect, the reduction of life of wall due to the irradiation of high fluence must be considered. The surface damage due to plasma disruption is a very big problem. The activities concerning the surface studies in university-linked organizations are the surface characterization for fusion reactor materials by low energy ion scattering spectroscopy, the high power ion irradiation test for CTR first wall, data compilation on plasma-wall interaction, the studies of sputtering process and surface coating, and the study on hydrogen isotope permeation through metals for fusion reactors. Other activities such as the sample characterization at many universities using the SUS 304 samples from the same lot, and the collaboration works on JIPP-T-2 plasma wall experiments are introduced. Concerning the surface study, US-Japan or international collaboration are strongly expected. (Kato, T.)

Impoundment effects in the population of Auchenipterus osteomystax (Siluriformes: Auchenipteridae: a Neotropical reservoir case

Directory of Open Access Journals (Sweden)

Elcio Barili

2012-06-01

Full Text Available New impoundments provide opportunities to check whether species that present enough feeding flexibility in natural conditions may take advantage of this situation and, without reproductive restriction, can occupy the most conspicuous habitat in a large reservoir (open areas and present higher success in the colonization of the new environment. We examined variations in the abundance and feeding of A. osteomystax in two environments, one natural (Sinha Mariana floodplain lake and one dammed (Manso Reservoir, during two periods: the first year after the filling phase and three years later. Our goal was to evaluate the occupation of the new hábitat (Manso Reservoir, by this species, as well as to test the hypothesis that in the reservoir, unlike the natural environment, there are remarkable changes in diet between the periods. Fish were sampled monthly in the floodplain lake and in the reservoir during two annual periods using gillnets. To evaluate the differences in abundance of A. osteomystax we employed the Kruskal -Wallis test, and the diet analysis was carried out using frequency of occurrence and volumetric methods. Temporal differences in the diet were tested by Kruskal-Wallis test using the scores from a detrended correspondence analysis. A. osteomystax was significantly more abundant in the floodplain lake, where the captures were higher than in the reservoir in almost all months analyzed, and significant variations in abundance between the two periods were not recorded in either the reservoir or the floodplain lake. The diet variation between the two periods, which had a time lag of three years between them, was much less pronounced in the natural environment, where the resource availability is essentially regulated by seasonality. Thus, our hypothesis was accepted; that is, the interannual variations in the diet of A. osteomystax are more relevant in an artificial environment than in a natural one. Rev. Biol. Trop. 60 (2: 699-708. Epub

Surface studies of plasma processed Nb samples

International Nuclear Information System (INIS)

Tyagi, Puneet V.; Doleans, Marc; Hannah, Brian S.; Afanador, Ralph; Stewart, Stephen; Mammosser, John; Howell, Matthew P; Saunders, Jeffrey W; Degraff, Brian D; Kim, Sang-Ho

2015-01-01

Contaminants present at top surface of superconducting radio frequency (SRF) cavities can act as field emitters and restrict the cavity accelerating gradient. A room temperature in-situ plasma processing technology for SRF cavities aiming to clean hydrocarbons from inner surface of cavities has been recently developed at the Spallation Neutron Source (SNS). Surface studies of the plasma-processed Nb samples by Secondary ion mass spectrometry (SIMS) and Scanning Kelvin Probe (SKP) showed that the NeO_2 plasma processing is very effective to remove carbonaceous contaminants from top surface and improves the surface work function by 0.5 to 1.0 eV.

40 CFR 264.230 - Special requirements for incompatible wastes.

Science.gov (United States)

2010-07-01

... DISPOSAL FACILITIES Surface Impoundments § 264.230 Special requirements for incompatible wastes... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Special requirements for incompatible wastes. 264.230 Section 264.230 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED...

Algae and Partiele Removal in Direct Filtration of Biesbosch Water: Influence of Algal Characteristics, Oxidation and other Pre-treatment Conditions

NARCIS (Netherlands)

Petrusvenski, B.

1996-01-01

Direct flitration is an economicaily and environmentally attractive altemative to conventional treatment of impounded surface watei, provided that the waler bource is of appropriate quality, However, direct filtration has limited partiele and algae removal capacity. Problems related to algae and

Dam-break studies for mine tailings impoundments

International Nuclear Information System (INIS)

Jeyapalan, J.K.

1982-01-01

This paper describes simple procedures for performing dam-break analyses. Tailings from dam failures usually liquefy and flow for substantial distances as a viscous fluid. The prediction of the possible extent of flow slide movement is illustrated using two case histories. Topics considered include the flow behavior of liquefied talings, dimensionsless numbers for mine tailings and associated flow regimes, laminar flow, and turbulent flow. The potential inundation regions downstream of mine tailings dams are assessed. It is concluded that instances of flow slides of mine waste embankments indicate that the failure of these structures has considerable potential for damage to life and property in many cases

LADTAP-2, Organ Doses to Man and Other Biota from Aquatic Environment

International Nuclear Information System (INIS)

Strenge, D.L.; Peloquin, R.A.; Whelan, G.

1989-01-01

1 - Description of problem or function: LADTAP2 performs environmental dose analyses for releases of liquid effluents from light-water nuclear power plants into surface waters during routine operation. The analyses estimate radiation doses to individuals, population groups, and biota from ingestion (aquatic foods, water, and terrestrial irrigated foods) and external exposure (shoreline, swimming, and boating) pathways. The calculated doses provide information for National Environmental Policy Act (NEPA) evaluations and for determining compliance with Appendix I of 10 CFR 50 (the 'ALARA' philosophy). The program consists of a hydrologic model chosen to represent mixing in the effluent impoundment system and the receiving surface waters and the exposure pathway models which estimate exposure of selected groups at various water usage locations in the environment. Two types of population doses are calculated. An ALARA analysis is performed based on exposure of people within 50 miles of the site, and a NEPA analysis is performed based on exposure of the entire U.S. population to effluents from the site. A population-dose analysis prepared in the form of a cost-benefit table presents the total-body and thyroid doses from each radionuclide released and the population doses (total-body and thyroid) per curie of each radionuclide released. 2 - Method of solution: The impoundment system is represented by one of four hydrologic models: direct release to the receiving water, linear flow with no mixing (the plug-flow model), linear flow through the impoundment with partial recirculation through the reactor (the partially mixed model), or complete mixing in the impoundment with partial recirculation through the reactor (the completely mixed model). The last three account for radiological decay during transit through the impoundment system. Optional models are available to estimate dilution in nontidal rivers and near-shore lake environments. The consequence calculation part of

Reclamation Strategies and Geomorphic Outcomes in Coal Surface Mines of Eastern Ohio

Science.gov (United States)

Pollock, M.; Jaeger, K. L.

2014-12-01

Coal surface mining is a significant landscape disturbance in the United States. Since 1977, the reclamation of mined lands has been regulated by the Surface Mine Control and Reclamation Act (SMCRA). Prior to the act, many coalfields were left un-reclaimed or partially reclaimed, with highly irregular topology and drainage networks. Under the act, the reverse is often true; adherence to SMCRA often leads to the homogenization of surfaces and channel networks. While both pre and post-SMCRA landscapes are highly altered, they exhibit strongly dissimilar characteristics. We examine pre-SMCRA, post-SMCRA and unmined watersheds at 3 spatial scales in order to compare the geomorphic differences between reclamation strategies. In particular, we attempt to separate anthropogenic factors from pre-existing, natural factors via comparisons to unmined watersheds. Our study design incorporates a 3 scale top-down analysis of 21 independent watersheds (7 of each treatment type). Each watershed has an area of approximately 1km2. All watersheds share similar geography, climate and geology. At the landscape scale, characteristics are derived from 0.762m (2.5ft) resolution Digital Elevation Models (DEMs). At the channel network scale, DEMs, as well as remote sensing data (including the National Wetlands Inventory database) are used. Finally, the reach scale incorporates longitudinal and cross-section surveys (using a total station) as well as a particle size distribution. At each scale, attributes are parameterized for statistical comparison. Post-SMCRA sites are characterized by a general reduction of watershed surface slopes (11.9% median) compared to pre-SMCRA (19.3%) and unmined (19.8%) sites. Both pre and post-SMCRA channel networks are characterized by significant surface impoundments (in the form of remnant headwall trenches on pre-SMCRA sites and engineered retention basins on post-SMCRA sites). Pre-SMCRA outlet reaches have significantly steeper bed slopes (2.79% mean) than

Surface study of liquid 3He using surface state electrons

International Nuclear Information System (INIS)

Shirahama, K.; Ito, S.; Suto, H.; Kono, K.

1995-01-01

We have measured the mobility of surface state electrons (SSE) on liquid 3 He, μ 3 , aiming to study the elementary surface excitations of the Fermi liquid. A gradual increase of μ 3 below 300 mK is attributed to the scattering of electrons by ripplons. Ripplons do exist in 3 He down to 100 mK. We observe an abrupt decrease of μ 3 , due to the transition to the Wigner solid (WS). The dependences of the WS conductivity and mobility on temperature and magnetic field differ from the SSE behavior on liquid 4 He

76 FR 9376 - Proposed Extension of Existing Information Collection;

Science.gov (United States)

2011-02-17

... Extension of Existing Information Collection; Refuse Piles and Impoundment Structures, Recordkeeping and... surface installations. More specifically, these sections address refuse piles (30 CFR 77.215), and... combination of materials; and refuse piles are deposits of coal mine waste (other than overburden or spoil...

Influences of Coal Ash Leachates and Emergent Macrophytes on Water Quality in Wetland Microcosms

Science.gov (United States)

The storage of coal combustion residue (CCR) in surface water impoundments may have an impact on nearby water quality and aquatic ecosystems. CCR contains leachable trace elements that can enter nearby waters through spills and monitored discharge. It is important, therefore, to ...

Energy loss spectroscopy applied to surface studies

International Nuclear Information System (INIS)

Lecante, J.

1975-01-01

The analysis of energy losses suffered by slow electrons (5 eV to 300 eV) back-scattered by single crystal surfaces appears to be a powerful method for surfaces studies. The inelastic scattering of these slow electrons limits their escape depth to the surface region which is defined here. After a review of the basic excitation processes due to the interaction between electrons and surfaces (phonons, plasmons and electronic transitions) a brief discussion is given about the instruments needed for this electron spectroscopy. Finally some experimental results are listed and it is shown that the comparison of the results given by ELS with other surface sensitive methods such as UPS is very fruitful and new information can be obtained [fr

TED Study of Si(113) Surfaces

Science.gov (United States)

Suzuki, T.; Minoda, H.; Tanishiro, Y.; Yagi, K.

A TED study of Si(113) surfaces was carried out. Reflections from the 3 × 2 reconstruction were seen at room temperature, while half-order reflections were very faint. The surface showed the phase transition between the 3 × 1 and the disordered (rough) structures at about 930°C. The (113) surface structure at room temperature was analyzed using TED intensity. Four kinds of structure models proposed previously, including both the 3 × 1 and the 3 × 2 reconstructed structures, were examined. The R-factors calculated using the energy-optimized atomic coordinates are not sufficiently small. After minimization of the R-factors, Dabrowski's 3 × 2 structure model is most agreeable, while Ranke's 3 × 1 and 3 × 2 structure models are not to be excluded. STM observation showed that the surface is composed of small domains of the 3 × 2 structure.

Medico-ecological study and health impact assessment of hydro-electric projects in Malaysia

Energy Technology Data Exchange (ETDEWEB)

Lai, Karen [Institute for Medical Research, Kuala Lumpur (Malaysia)

1997-12-31

The objectives of this studies were to determine i) if there was any potential health risks in terms of spread of vector-borne and other communicable diseases resulting from the changes in the environment due to creation of large bodies of water as consequence of the construction of dams, ii) diseases of public health importance in populations affected by such projects. Nine pre-impoundment studies had been carried out and potential impact of the change in environment on discases and health of the affected populations in each areas was evaluated. Risk of infections to the dam construction workers also assessed. Recommendations on mitigation measures were made for each situation so that adequate provisions could be made to improve the health conditions of these populations especially those who would be resettled as a result of impoundment . Prevention and control measures on transmission of infection, including vector control were proposed. The potential medico-ecological hazards encountered by immigrants and visitors to the area on completion of the hydro project were also envisaged.

Medico-ecological study and health impact assessment of hydro-electric projects in Malaysia

International Nuclear Information System (INIS)

Karen Lai

1996-01-01

The objectives of this studies were to determine i) if there was any potential health risks in terms of spread of vector-borne and other communicable diseases resulting from the changes in the environment due to creation of large bodies of water as consequence of the construction of dams, ii) diseases of public health importance in populations affected by such projects. Nine pre-impoundment studies had been carried out and potential impact of the change in environment on discases and health of the affected populations in each areas was evaluated. Risk of infections to the dam construction workers also assessed. Recommendations on mitigation measures were made for each situation so that adequate provisions could be made to improve the health conditions of these populations especially those who would be resettled as a result of impoundment . Prevention and control measures on transmission of infection, including vector control were proposed. The potential medico-ecological hazards encountered by immigrants and visitors to the area on completion of the hydro project were also envisaged

Sum-frequency spectroscopic studies: I. Surface melting of ice, II. Surface alignment of polymers

Energy Technology Data Exchange (ETDEWEB)

Wei, Xing [Univ. of California, Berkeley, CA (United States)

2000-01-01

Surface vibrational spectroscopy via infrared-visible sum-frequency generation (SFG) has been established as a useful tool to study the structures of different kinds of surfaces and interfaces. This technique was used to study the (0001) face of hexagonal ice (Ih). SFG spectra in the O-H stretch frequency range were obtained at various sample temperatures. For the vapor(air)/ice interface, the degree of orientational order of the dangling OH bonds at the surface was measured as a function of temperature. Disordering sets in around 200 K and increases dramatically with temperature, which is strong evidence of surface melting of ice. For the other ice interfaces (silica/OTS/ice and silica/ice), a similar temperature dependence of the hydrogen bonded OH stretch peak was observed; the free OH stretch mode, however, appears to be different from that of the vapor (air)/ice interface due to interactions at the interfaces. The technique was also used to measure the orientational distributions of the polymer chains on a rubbed polyvinyl alcohol surface. Results show that the polymer chains at the surface appear to be well aligned by rubbing, and the adsorbed liquid crystal molecules are aligned, in turn, by the surface polymer chains. A strong correlation exists between the orientational distributions of the polymer chains and the liquid crystal molecules, indicating that the surface-induced bulk alignment of a liquid crystal film by rubbed polymer surfaces is via an orientational epitaxy-like mechanism. This thesis also contains studies on some related issues that are crucial to the above applications. An experiment was designed to measure SFG spectra in both reflection and transmission. The result confirms that SFG in reflection is generally dominated by the surface contribution. Another issue is the motional effect due to fast orientational motion of molecules at a surface or interface. Calculations show that the effect is significant if the molecular orientation varies

Role of surface studies in science and technology

Energy Technology Data Exchange (ETDEWEB)

Karkhanavala, M D [Bhabha Atomic Research Centre, Bombay (India). Chemistry Div.

1977-01-01

Reactivity of solids is influenced by the surface properties such as structure, dislocations and composition. Corrosion and erosion are essentially surface phenomena. Surface studies, therefore, assume importance in prevention and minimization of corrosion and erosion. Discussion is illustrated with examples drawn from the field of nuclear power reactor technology.

Surface and Interface Studies with Radioactive Ions

CERN Multimedia

Weber, A

2002-01-01

Investigations on the atomic scale of magnetic surfaces and magnetic multilayers were performed by Perturbed Angular Correlation (PAC) spectroscopy. The unique combination of the Booster ISOLDE facility equipped with a UHV beamline and the UHV chamber ASPIC (Apparatus for Surface Physics and Interfaces at CERN) is ideally suited for such microscopic studies. Main advantages are the choice of problem-oriented radioactive probes and the purity of mass-separated beams. The following results were obtained: $\\,$i) Magnetic hyperfine fields (B$_{hf}$) of Se on Fe, Co, Ni surfaces were determined. The results prompted a theoretical study on the B$_{hf}$ values of the 4sp-elements in adatom position on Ni and Fe, confirming our results and predicting unexpected behaviour for the other elements. $\\,$ii) Exemplarily we have determined B$_{hf}$ values of $^{111}$Cd at many different adsorption sites on Ni surfaces. We found a strong dependence on the coordination number of the probes. With decreasing coordination nu...

40 CFR 264.221 - Design and operating requirements.

Science.gov (United States)

2010-07-01

..., and other equipment; and human error. (h) A surface impoundment must have dikes that are designed... (CONTINUED) STANDARDS FOR OWNERS AND OPERATORS OF HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL FACILITIES... external hydrogeologic forces), physical contact with the waste or leachate to which they are exposed...

40 CFR 264.1086 - Standards: Containers.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Standards: Containers. 264.1086... Air Emission Standards for Tanks, Surface Impoundments, and Containers § 264.1086 Standards: Containers. (a) The provisions of this section apply to the control of air pollutant emissions from...

40 CFR 63.961 - Definitions.

Science.gov (United States)

2010-07-01

... system used to convey regulated-material to a waste management unit or to discharge or disposal. The term...-material to a downstream waste management unit. Sewer lines include pipes, grates, and trenches. Waste... regulated-material. Examples of waste management units include: wastewater tanks, surface impoundments...

Liner used in tailings ponds

International Nuclear Information System (INIS)

Dinchak, W.G.

1984-01-01

A composite liner has been developed for use in hazardous waste impoundments and in tailings ponds where uranium is involved. The liner offers a high degree of reliability against seepage, is durable, and provides a firm working surface. The advantages of the liner are discussed

40 CFR 144.3 - Definitions.

Science.gov (United States)

2010-07-01

... operations, and sinks or washing machines where food and beverage serving dishes, glasses, and utensils are.... Hazardous waste management facility (“HWM facility”) means all contiguous land, and structures, other... landfills, surface impoundments, or combination of them). HWM facility means “Hazardous Waste Management...

40 CFR 63.681 - Definitions.

Science.gov (United States)

2010-07-01

... drain system, a gravity-operated conveyor (such as a chute), and a mechanically-powered conveyor (such... features permanently integrated into the design of the unit. Emission point means an individual tank, surface impoundment, container, oil-water or organic-water separator, transfer system, process vent, or...

77 FR 1267 - National Emission Standards for Hazardous Air Pollutant Emissions: Group IV Polymers and Resins...

Science.gov (United States)

2012-01-09

... Cooling Tower PEPO--Polyether Polyols PET--Poly (Ethylene Terephthalate) Resin PM--Particulate Matter POM...., fixed roofs on storage vessels and oil water separators; covers on surface impoundments, containers and... category: Solid-state resins (PET bottle grade resins), polyester film and engineering resins. They are all...

Impacts of the Three Gorges Project on Local Climate

Science.gov (United States)

Song, Z.; Liang, S.; Feng, L.

2015-12-01

Three Gorges Project (TGP) is the largest hydroelectric project in the world and has led to significant land cover changes in Three Gorges Reservoir Area (TGRA). Since its construction the debates on its environmental and climatic impacts have never stopped, especially after the extreme drought and flood in Yangtze River Basin these years. TGP reached its final impounding water level in 2010. However, studies on systematically monitoring the long-term variations in surface and atmospheric parameters in TGRA are still lacking. In this study, three important surface parameters - surface albedo, land surface temperature (LST) and evapotranspiration (ET) and two climatic parameters - air temperature and precipitation were investigated from 2000 to 2013 by combining multiple remote sensing data and ground measurements. Results showed that along the reservoir albedo decreased significantly as a result of water impounding. Correspondingly, in the same region daytime LST decreased in spring and summer and nighttime LST increased in autumn and winter. In the western region of TGRA, albedo increased due to resettlement and LST also changed. The average ET increased by 20% in TGR but kept stable in the whole TGRA. In contrast to LST, air temperature showed less apparent spatial and temporal variability. Only in the region near the dam air temperature experienced a decrease at daytime and an increase at nighttime. Further analysis demonstrated precipitation revealed no apparent changes in TGRA and the precipitation anomaly in northwest of TGRA may not be connected with TGP. All of the findings provide a more substantial clues of local climate change caused by TGP.

SFG and AFM Studies of Polymer Surface Monolayers

Science.gov (United States)

Somorjai, Gabor A.

2003-03-01

Sum frequency generation vibrational spectroscopy and atomic force microscopy techniques were utilized to study the structure and composition of polymer surfaces ranging from polyethylene and polypropylene to copolymers of polyurethane and polystyrene. The surface methyl groups aligned perpendicular to the surface above the glass transition temperature of polypropylene. Large side groups such as the phenyl group on polystyrene is also near the surface normal at the polymer-air interface. At the air interface hydrophobic groups are dominant on the polymer surface while at solid-water interface hydrophilic groups segregate to the surface. Minimizing surface energy is the cause of readjusting the surface composition at polymer-water interfaces as compared to polymer-air interfaces. Upon stretching the soft component of two-component polymer systems segregates to the surface and both the surface structure and the surface composition undergo reversible or irreversible changes depending on the magnitude of the stretch. Since the heart beat forces bio-polymers to stretch over 40 million times a year the molecular behavior due to stretching has important physiological consequences.

Oxidation of clean silicon surfaces studied by four-point probe surface conductance measurements

DEFF Research Database (Denmark)

Petersen, Christian Leth; Grey, Francois; Aono, M.

1997-01-01

We have investigated how the conductance of Si(100)-(2 x 1) and Si(111)-(7 x 7) surfaces change during exposure to molecular oxygen. A monotonic decrease in conductance is seen as the (100) surfaces oxidizes. In contract to a prior study, we propose that this change is caused by a decrease in sur...

Platelet adhesion studies on dipyridamole coated polyurethane surfaces

Directory of Open Access Journals (Sweden)

Aldenhoff Y. B.J.

2003-06-01

Full Text Available Surface modification of polyurethanes (PUs by covalent attachment of dipyridamole (Persantinregistered is known to reduce adherence of blood platelets upon exposure to human platelet rich plasma (PRP. This effect was investigated in further detail. First platelet adhesion under static conditions was studied with four different biomaterial surfaces: untreated PU, PU immobilised with conjugate molecule 1, PU immobilised with conjugate molecule 2, and PU immobilised with conjugate molecule 3. In PU immobilised with 1 dipyridamole is directly linked to the surface, in PU immobilised with 2 there is a short hydrophilic spacer chain in between the surface and the dipyridamole, while conjugate molecule 3 is merely the spacer chain. Scanning electron microscopy (SEM was used to characterise platelet adhesion from human PRP under static conditions, and fluorescence imaging microscopy was used to study platelet adhesion from whole blood under flow. SEM experiments encompassed both density measurements and analysis of the morphology of adherent platelets. In the static experiments the surface immobilised with 2 showed the lowest platelet adherence. No difference between the three modified surfaces emerged from the flow experiments. The surfaces were also incubated with washed blood platelets and labeled with Oregon-Green Annexin V. No capture of Oregon-Green Annexin V was seen, implying that the adhered platelets did not expose any phosphatidyl serine at their exteriour surface.

Seasonal and temporal patterns of NDMA formation potentials in surface waters.

Science.gov (United States)

Uzun, Habibullah; Kim, Daekyun; Karanfil, Tanju

2015-02-01

The seasonal and temporal patterns of N-nitrosodimethylamine (NDMA) formation potentials (FPs) were examined with water samples collected monthly for 21 month period in 12 surface waters. This long term study allowed monitoring the patterns of NDMA FPs under dynamic weather conditions (e.g., rainy and dry periods) covering several seasons. Anthropogenically impacted waters which were determined by high sucralose levels (>100 ng/L) had higher NDMA FPs than limited impacted sources (NDMA FP showed more variability in spring months, while seasonal mean values remained relatively consistent. The study also showed that watershed characteristics played an important role in the seasonal and temporal patterns. In the two dam-controlled river systems (SW A and G), the NDMA FP levels at the downstream sampling locations were controlled by the NDMA levels in the dams independent of either the increases in discharge rates due to water releases from the dams prior to or during the heavy rain events or intermittent high NDMA FP levels observed at the upstream of dams. The large reservoirs and impoundments on rivers examined in this study appeared serving as an equalization basin for NDMA precursors. On the other hand, in a river without an upstream reservoir (SW E), the NDMA levels were influenced by the ratio of an upstream wastewater treatment plant (WWTP) effluent discharge to the river discharge rate. The impact of WWTP effluent decreased during the high river flow periods due to rain events. Linear regression with independent variables DOC, DON, and sucralose yielded poor correlations with NDMA FP (R(2) NDMA FP (R(2) = 0.53). Copyright © 2014 Elsevier Ltd. All rights reserved.

40 CFR 265.1087 - Standards: Containers.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Standards: Containers. 265.1087... DISPOSAL FACILITIES Air Emission Standards for Tanks, Surface Impoundments, and Containers § 265.1087 Standards: Containers. (a) The provisions of this section apply to the control of air pollutant emissions...

76 FR 23522 - Oklahoma Regulatory Program

Science.gov (United States)

2011-04-27

... the impoundment or a water balance (precipitation runoff versus lake evaporation) showing that the... underground mine workings. The full text of the program amendment is available for you to read at the... Intergovernmental relations, Surface mining, Underground mining. Dated: March 4, 2011. Ervin J. Barchenger, Regional...

Extended characterization of M-Area settling basin and vicinity. Technical data summary. Revision

Energy Technology Data Exchange (ETDEWEB)

Pickett, J B

1985-10-01

The Savannah River Plant M-Area settling basin, an unlined surface impoundment, has received process effluents from the M-Area fuel and target fabrication facilities since 1958. The waste effluents have contained metal degreasing agents (chlorinated hydrocarbons), acids, caustics, and heavy metals. Data analyses are provided.

Installation Restoration Program. Phase 2. Confirmation McClellan AFB, California. Volume 1

Science.gov (United States)

1983-06-01

testing in accordance with ASTH C 828-78 and in conformance with CAL/ OSHA safety orders and ES Industrial Sewer Entry Procedures. Indi- viduals entering...Liquid Palm Cil Wastes," Proceedings: Asia Acuatech, Singapore, Malaysia , March 1980 (Coauthors R. White and C. Ponniah). "Surface Impoundment of

40 CFR 445.1 - General applicability.

Science.gov (United States)

2010-07-01

... discharges from land application or land treatment units, surface impoundments, underground injection wells, waste piles, salt dome formations, salt bed formations, underground mines or caves as these terms are... ground water or wastewater from recovery pumping wells. (e) This part does not apply to discharges of...

Positron beam studies of solids and surfaces: A summary

International Nuclear Information System (INIS)

Coleman, P.G.

2006-01-01

A personal overview is given of the advances in positron beam studies of solids and surfaces presented at the 10th International Workshop on Positron Beams, held in Doha, Qatar, in March 2005. Solids studied include semiconductors, metals, alloys and insulators, as well as biophysical systems. Surface studies focussed on positron annihilation-induced Auger electron spectroscopy (PAES), but interesting applications of positron-surface interactions in fields as diverse as semiconductor technology and studies of the interstellar medium serve to illustrate once again the breadth of scientific endeavour covered by slow positron beam investigations

Positron beam studies of solids and surfaces: A summary

Science.gov (United States)

Coleman, P. G.

2006-02-01

A personal overview is given of the advances in positron beam studies of solids and surfaces presented at the 10th International Workshop on Positron Beams, held in Doha, Qatar, in March 2005. Solids studied include semiconductors, metals, alloys and insulators, as well as biophysical systems. Surface studies focussed on positron annihilation-induced Auger electron spectroscopy (PAES), but interesting applications of positron-surface interactions in fields as diverse as semiconductor technology and studies of the interstellar medium serve to illustrate once again the breadth of scientific endeavour covered by slow positron beam investigations.

Bedload transport over run-of-river dams, Delaware, U.S.A.

Science.gov (United States)

Pearson, Adam J.; Pizzuto, Jim

2015-11-01

We document the detailed morphology and bed sediment size distribution of a stream channel upstream and downstream of a 200-year-old run-of-river dam on the Red Clay Creek, a fifth order stream in the Piedmont of northern Delaware, and combine these data with HEC-RAS modeling and bedload transport computations. We hypothesize that coarse bed material can be carried through run-of-river impoundments before they completely fill with sediment, and we explore mechanisms to facilitate this transport. Only 25% of the accommodation space in our study site is filled with sediment, and maximum water depths are approximately equal to the dam height. All grain-size fractions present upstream of the impoundment are also present throughout the impoundment. A characteristic coarse-grained sloping ramp leads from the floor of the impoundment to the crest of the dam. A 2.3-m-deep plunge pool has been excavated below the dam, followed immediately downstream by a mid-channel bar composed of coarse bed material similar in size distribution to the bed material of the impoundment. The mid-channel bar stores 1472 m3 of sediment, exceeding the volume excavated from the plunge pool by a factor of 2.8. These field observations are typical of five other sites nearby and suggest that all bed material grain-size fractions supplied from upstream can be transported through the impoundment, up the sloping ramp, and over the top of the dam. Sediment transport computations suggest that all grain sizes are in transport upstream and within the impoundment at all discharges with return periods from 1 to 50 years. Our computations suggest that transport of coarse bed material through the impoundment is facilitated by its smooth, sandy bed. Model results suggest that the impoundment is currently aggrading at 0.26 m/year, but bed elevations may be recovering after recent scour from a series of large floods during water year 2011-2012. We propose that impoundments upstream of these run-of-river dams

Ti and Zr surfaces studied by molecular dynamics

International Nuclear Information System (INIS)

Pascuet, Maria I.; Passianot, Roberto C.; Monti, Ana M.

2003-01-01

The interaction between point defects technique and the (0001), (1-210), (10-10) surfaces in Ti and Zr is studied by the molecular dynamics technique. Both of metals are in the hexagonal structure and within a temperature range of 100 to 900 K. The atomic interactions are modeled by EAM-type many-body potentials, that were used previously in static simulations. New migration mechanisms are unraveled and others are verified with respect to those already proposed in the static studies. Also included is an analysis of the vacancy stability in the sub-surface layers of the prismatic surfaces. (author)

3D SEM for surface topography quantification – a case study on dental surfaces

International Nuclear Information System (INIS)

Glon, F; Flys, O; Lööf, P-J; Rosén, B-G

2014-01-01

3D analysis of surface topography is becoming a more used tool for industry and research. New ISO standards are being launched to assist in quantifying engineering surfaces. The traditional optical measuring instrumentation used for 3D surface characterization has been optical interferometers and confocal based instrumentation. However, the resolution here is limited in the lateral dimension to the wavelength of visible light to about 500 nm. The great advantage using the SEM for topography measurements is the high flexibility to zoom from low magnifications and locating interesting areas to high magnification of down to nanometer large surface features within seconds. This paper presents surface characterization of dental implant micro topography. 3D topography data was created from SEM images using commercial photogrammetric software. A coherence scanning interferometer was used for reference measurements to compare with the 3D SEM measurements on relocated areas. As a result of this study, measurements emphasizes that the correlation between the accepted CSI measurements and the new technology represented by photogrammetry based on SEM images for many areal characterization parameters are around or less than 20%. The importance of selecting sampling and parameter sensitivity to varying sampling is high-lighted. Future work includes a broader study of limitations of the photogrammetry technique on certified micro-geometries and more application surfaces at different scales

Study the Postbuckling of Hexagonal Piezoelectric Nanowires with Surface Effect

Directory of Open Access Journals (Sweden)

O. Rahmani

2014-04-01

Full Text Available Piezoelectric nanobeams having circular, rectangular and hexagonal cross-sections are synthesized and used in various Nano structures; however, piezoelectric nanobeams with hexagonal cross-sections have not been studied in detail. In particular, the physical mechanisms of the surface effect and the role of surface stress, surface elasticity and surface piezoelectricity have not been discussed thoroughly. The present study investigated post-buckling behavior of piezoelectric nanobeams by examining surface effects. The energy method was applied to post-buckling of hexagonal nanobeams and the critical buckling voltage and amplitude are derived analytically from bulk and surface material properties and geometric factors.

Modern methods of studying surfaces and their application to glasses

International Nuclear Information System (INIS)

Rauschenbach, B.; Haehnert, M.

1977-05-01

In the works are demonstrated modern methods for study of solid surfaces and its use of glasses. Study of the interaction of ions, electrons and photons with the glass surface provides information about the composition of the surface and its structure on an atomic scale. A qualitative analysis of a surface can be made with the aid of the Auger electron spectroscopy (AES) and the electron spectroscopy for chemical analysis (ESCA) and with the ion scattering (ISS and RBS) and the secondary ion mass spectrometry (SIMS). The structure of a surface can be studied by means of ion scattering and low-energy electron diffraction (LEED) and the topography of a surface by means of scanning electron microscopy (SEM). The ellipsometry is generally confined to measuring the thickness of very thin layers. The application these methods to the glass surfaces is demonstrated on series of examples. (author)

Surface diffusion studies by optical diffraction techniques

International Nuclear Information System (INIS)

Xiao, X.D.

1992-11-01

The newly developed optical techniques have been combined with either second harmonic (SH) diffraction or linear diffraction off a monolayer adsorbate grating for surface diffusion measurement. Anisotropy of surface diffusion of CO on Ni(l10) was used as a demonstration for the second harmonic dim reaction method. The linear diffraction method, which possesses a much higher sensitivity than the SH diffraction method, was employed to study the effect of adsorbate-adsorbate interaction on CO diffusion on Ni(l10) surface. Results showed that only the short range direct CO-CO orbital overlapping interaction influences CO diffusion but not the long range dipole-dipole and CO-NI-CO interactions. Effects of impurities and defects on surface diffusion were further explored by using linear diffraction method on CO/Ni(110) system. It was found that a few percent S impurity can alter the CO diffusion barrier height to a much higher value through changing the Ni(110) surface. The point defects of Ni(l10) surface seem to speed up CO diffusion significantly. A mechanism with long jumps over multiple lattice distance initiated by CO filled vacancy is proposed to explain the observed defect effect

78 FR 22873 - Hamilton Street Hydro, LLC; Notice of Preliminary Permit Application Accepted for Filing and...

Science.gov (United States)

2013-04-17

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Project No. 14500-000] Hamilton Street... Hydroelectric Project would consist of the following: (1) An existing 14-foot-high concrete gravity dam with a 480-foot-long spillway; (2) an existing impoundment having a surface area of 50 acres and a storage...

40 CFR 63.941 - Definitions.

Science.gov (United States)

2010-07-01

... another subpart that references the use of this subpart, then the definition in this subpart shall take precedence when implementing this subpart. Closure device means a cap, hatch, lid, plug, seal, valve, or... a surface impoundment cover when the device is secured in the closed position. Closure devices...

Study of Magnetohydrodynamic Surface Waves on Liquid Gallium

Energy Technology Data Exchange (ETDEWEB)

Hantao Ji; William Fox; David Pace; H.L. Rappaport

2004-05-13

Magnetohydrodynamic (MHD) surface waves on liquid gallium are studied theoretically and experimentally in the small magnetic Reynolds number limit. A linear dispersion relation is derived when a horizontal magnetic field and a horizontal electric current is imposed. No wave damping is found in the shallow liquid limit while waves always damp in the deep liquid limit with a magnetic field parallel to the propagation direction. When the magnetic field is weak, waves are weakly damped and the real part of the dispersion is unaffected, while in the opposite limit waves are strongly damped with shortened wavelengths. In a table-top experiment, planar MHD surface waves on liquid gallium are studied in detail in the regime of weak magnetic field and deep liquid. A non-invasive diagnostic accurately measures surface waves at multiple locations by reflecting an array of lasers off the surface onto a screen, which is recorded by an Intensified-CCD camera. The measured dispersion relation is consistent with the linear theory with a reduced surface tension likely due to surface oxidation. In excellent agreement with linear theory, it is observed that surface waves are damped only when a horizontal magnetic field is imposed parallel to the propagation direction. No damping is observed under a perpendicular magnetic field. The existence of strong wave damping even without magnetic field suggests the importance of the surface oxide layer. Implications to the liquid metal wall concept in fusion reactors, especially on the wave damping and a Rayleigh-Taylor instability when the Lorentz force is used to support liquid metal layer against gravity, are discussed.

Study of Magnetohydrodynamic Surface Waves on Liquid Gallium

International Nuclear Information System (INIS)

Hantao Ji; William Fox; David Pace; Rappaport, H.L.

2004-01-01

Magnetohydrodynamic (MHD) surface waves on liquid gallium are studied theoretically and experimentally in the small magnetic Reynolds number limit. A linear dispersion relation is derived when a horizontal magnetic field and a horizontal electric current is imposed. No wave damping is found in the shallow liquid limit while waves always damp in the deep liquid limit with a magnetic field parallel to the propagation direction. When the magnetic field is weak, waves are weakly damped and the real part of the dispersion is unaffected, while in the opposite limit waves are strongly damped with shortened wavelengths. In a table-top experiment, planar MHD surface waves on liquid gallium are studied in detail in the regime of weak magnetic field and deep liquid. A non-invasive diagnostic accurately measures surface waves at multiple locations by reflecting an array of lasers off the surface onto a screen, which is recorded by an Intensified-CCD camera. The measured dispersion relation is consistent with the linear theory with a reduced surface tension likely due to surface oxidation. In excellent agreement with linear theory, it is observed that surface waves are damped only when a horizontal magnetic field is imposed parallel to the propagation direction. No damping is observed under a perpendicular magnetic field. The existence of strong wave damping even without magnetic field suggests the importance of the surface oxide layer. Implications to the liquid metal wall concept in fusion reactors, especially on the wave damping and a Rayleigh-Taylor instability when the Lorentz force is used to support liquid metal layer against gravity, are discussed

A comparison of resident fish assemblages in managed and unmanaged coastal wetlands in North Carolina and South Carolina

Science.gov (United States)

Robinson, Kelly F.; Jennings, Cecil A.

2014-01-01

The dominant fish species within impounded coastal wetlands in the southeastern US may be different from the species that dominate natural marshes. We tested the hypothesis that resident fish assemblages inhabiting impounded coastal wetlands in South Carolina would differ from resident assemblages in natural marshes of the southeastern United States. We used rarefied species richness, Shannon's H' diversity,J' evenness, Morisita's index of similarity, and the percent similarity index to compare resident fish assemblages from two impoundments to 12 open-marsh resident fish assemblages from previously published studies in North and South Carolina. We used rotenone to sample fish assemblages in impoundments. The assemblages in natural marsh habitat had been sampled with rotenone and seines. We classified comparisons yielding a similarity index ≥0.50 as moderately similar and those with an index ≥0.75 as very similar. Fifty-three percent of the among-impoundment comparisons (Morisita's index) were at least moderately similar, whereas 7% of impoundment—natural marsh comparisons were moderately similar. A difference in tidal influence was the only parameter in the best-fitting model describing the observed Morisita's indices. The index of similarity decreased by 63% when tidal influence differed between compared assemblages. Species richness and diversity were greater in impoundments than natural marshes, but evenness was similar between habitat types. Our results support the hypothesis that resident fish assemblages in impounded wetlands and natural marshes are different, and suggest that a degree of tidal influence is the most important factor behind the difference.

Spatial variations in water composition at a northern Canadian lake impacted by mine drainage

International Nuclear Information System (INIS)

Moncur, M.C.; Ptacek, C.J.; Blowes, D.W.; Jambor, J.L.

2006-01-01

Release of acid drainage from mine-waste disposal areas is a problem of international scale. Contaminated surface water, derived from mine wastes, originates both as direct surface runoff and, indirectly, as subsurface groundwater flow. At Camp Lake, a small Canadian Shield lake that is in northern Manitoba and is ice-covered 6 months of the year, direct and indirect release of drainage from an adjacent sulfide-rich tailings impoundment has severely affected the quality of the lake water. Concentrations of the products from sulfide oxidation are extremely high in the pore waters of the tailings impoundment. Groundwater and surface water derived from the impoundment discharge into a semi-isolated shallow bay in Camp Lake. The incorporation of this aqueous effluent has altered the composition of the lake water, which in turn has modified the physical limnology of the lake. Geochemical profiles of the water column indicate that, despite its shallow depth (6 m), the bay is stratified throughout the year. The greatest accumulation of dissolved metals and SO 4 is in the lower portion of the water column, with concentrations up to 8500 mg L -1 Fe, 20,000 mg L -1 SO 4 , 30 mg L -1 Zn, 100 mg L -1 Al, and elevated concentrations of Cu, Cd, Pb and Ni. Meromictic conditions and very high solute concentrations are limited to the bay. Outside the bay, solute concentrations are lower and some stratification of the water column exists. Identification of locations and composition of groundwater discharge relative to lake bathymetry is a fundamental aspect of understanding chemical evolution and physical stability of mine-impacted lakes

A Initio Theoretical Studies of Surfaces of Semiconductors

Science.gov (United States)

Wang, Jing

1993-01-01

The first semiconductor which we study with these techniques is the archetypal elemental semiconductor, silicon. We present the first extensive study of point defects on Si(100). We identify the principal defects and two primary mechanisms responsible for their dominance: the need to eliminate dangling bonds on the surface and the need to compensate the strain induced by topological effects. Furthermore, we present evidence that the presence of point defects on the Si(100) surface is not intrinsic to the ground state of the surface as a stress relieving mechanism but rather is due merely to thermal fluctuations. We address materials issues associated with the identification of the lowest energy surfaces of GaAs and the determination of the geometric structure of a GaAs crystallite growing freely in three dimensions. The fracture energies associated with (110), (100) and (111) interface planes are calculated and a Wulff construction indicates that an ideal stoichiometric GaAs crystal should be terminated with (110) surfaces. We investigate the more complex issues that arise on surfaces when aspects of these two semiconductors are mixed. We investigate the problem of growing GaAs on the Si(100) surface and demonstrate how and why the most fundamental properties of the resulting bulk GaAs material, such as its crystalline orientation, may depend sensitively on the interplay between growth conditions such as temperature and the properties of the Si surface. For stepped Si(100) -As, we show that the growth of As directly on top of the Si surface produces a metastable state, while the replacement of the original top Si layer leads to a lower energy configuration, with the rearrangement of the surface driven by the relaxation of stress by surface steps. Finally, we study delta -doping, where one attempts to grow a single layer of Si on a GaAs surface before continuing with the growth of bulk GaAs. We shall employ a slightly different modality of the ab initio approach. We

Investigation of geochemical indicators to evaluate the connection between inland and coastal groundwater systems near Kaloko-Honokōhau National Historical Park, Hawai‘i

International Nuclear Information System (INIS)

Tillman, Fred D; Oki, Delwyn S.; Johnson, Adam G.; Barber, Larry B.; Beisner, Kimberly R.

2014-01-01

Highlights: • The connection between inland and coastal aquifers near Kona, Hawai‘i is uncertain. • If connected, increased inland groundwater pumping may threaten coastal ecosystems. • Connection of inland and coastal aquifers was investigated using geochemical data. • Stable isotope results provide strong evidence of a connection between the systems. • Other geochemical data suggest a connection but are not conclusive. - Abstract: Kaloko-Honokōhau National Historical Park (KAHO) is a coastal sanctuary on the western side of the Island of Hawai‘i that was established in 1978 to preserve, interpret, and perpetuate traditional Native Hawaiian culture and activities. KAHO contains a variety of culturally and ecologically significant water resources and water-related habitat for species that have been declared as threatened or endangered by the U.S. Fish and Wildlife Service, or are candidate threatened or endangered species. These habitats are dependent on coastal unconfined groundwater in a freshwater-lens system. The coastal unconfined-groundwater system is recharged by local infiltration of rainfall but also may receive recharge from an inland groundwater system containing groundwater impounded to high altitudes. The area inland of and near KAHO is being rapidly urbanized and increased groundwater withdrawals from the inland impounded-groundwater system may affect habitat and water quality in KAHO, depending on the extent of connection between the coastal unconfined groundwater and inland impounded-groundwater. An investigation of the geochemistry of surface-water and groundwater samples in and near KAHO was performed to evaluate the presence or absence of a connection between the inland impounded- and coastal unconfined-groundwater systems in the area. Analyses of major ions, selected trace elements, rare-earth elements, and strontium-isotope ratio results from ocean, fishpond, anchialine pool, and groundwater samples were consistent with a linear

Study on Surface Permeability of Concrete under Immersion

OpenAIRE

Liu, Jun; Xing, Feng; Dong, Biqin; Ma, Hongyan; Pan, Dong

2014-01-01

In this paper, concrete specimens are immersed in ultrapure water, to study the evolutions of surface permeability, pore structure and paste microstructure following the prolonging of immersion period. According to the results, after 30-day immersion, the surface permeability of concrete becomes higher as compared with the value before immersion. However, further immersion makes the surface permeability decrease, so that the value measured after 150-day immersion is only half that measured af...

Single lump breast surface stress assessment study

Science.gov (United States)

Vairavan, R.; Ong, N. R.; Sauli, Z.; Kirtsaeng, S.; Sakuntasathien, S.; Paitong, P.; Alcain, J. B.; Lai, S. L.; Retnasamy, V.

2017-09-01

Breast cancer is one of the commonest cancers diagnosed among women around the world. Simulation approach has been utilized to study, characterize and improvise detection methods for breast cancer. However, minimal simulation work has been done to evaluate the surface stress of the breast with lumps. Thus, in this work, simulation analysis was utilized to evaluate and assess the breast surface stress due to the presence of a lump within the internal structure of the breast. The simulation was conducted using the Elmer software. Simulation results have confirmed that the presence of a lump within the breast causes stress on the skin surface of the breast.

Theoretical study of the surface resistivity of (111) surfaces of NixPt1-x(111) alloys

International Nuclear Information System (INIS)

Rous, P. J.

2001-01-01

A layer-Korringa - Kohn - Rostoker calculation is used to study the compositional dependence of the surface resistivity of the (111) surface of Ni x Pt 1-x (111) alloys. The compositional disorder in the bulk and at the surface is described by the coherent potential approximation. If it is assumed that the atomic planes near the (111) surface Ni x Pt 1-x have the same composition as the bulk layers, then a weak Nordheim effect is observed in the compositional dependence of the surface resistivity. However, we show that surface segregation in Ni x Pt 1-x (111) causes an inverse Nordheim dependence in the actual surface resistivity as the bulk composition is varied. [copyright] 2001 American Institute of Physics

Hydrogenation of nitriles on a well-characterized nickel surface: From surface science studies to liquid phase catalytic activity measurements

Energy Technology Data Exchange (ETDEWEB)

Gardin, Denis Emmanuel [Univ. of California, Berkeley, CA (United States)

1993-12-01

Nitrile hydrogenation is the most commonly used method for preparing diverse amines. This thesis is aimed at the mechanism and factors affecting the performance of Ni-based catalysts in nitrile hydrogenations. Surface science techniques are used to study bonding of nitriles and amines to a Ni(111) surface and to identify surface intermediates. Liquid-phase hydrogenations of cyclohexene and 1-hexene on a Pt foil were carried out successfully. Finally, knowledge about the surface structure, surface chemical bond, dynamics of surface atoms (diffusion, growth), and reactivity of metal surfaces from solid-gas interface studies, is discussed.

Study on surface wave characteristics of free surface flow of liquid metal lithium for IFMIF

International Nuclear Information System (INIS)

Hoashi, Eiji; Sugiura, Hirokazu; Yoshihashi-Suzuki, Sachiko; Yamaoka, Nobuo; Horiike, Hiroshi; Kanemura, Takuji; Kondo, Hiroo

2011-01-01

The international fusion materials irradiation facility (IFMIF) presents an intense neutron source to develop fusion reactor materials. The free surface flow of a liquid metal Lithium (Li) is planned as a target irradiated by two deuteron beams to generate intense neutrons and it is thus important to obtain knowledge of the surface wave characteristic for the safety and the efficiency of system in the IFMIF. We have been studying on surface wave characteristics experimentally using the liquid metal Li circulation facility at Osaka University and numerically using computational fluid dynamics (CFD) code, FLUENT. This paper reports the results of the surface fluctuation, the wave height and the surface velocity in the free surface flow of the liquid metal Li examined experimentally and numerically. In the experiment, an electro-contact probe apparatus was used to obtain the surface fluctuation and the wave height, and a high speed video was used to measure the surface velocity. We resulted in knowledge of the surface wave growth mechanism. On the other hand, a CFD simulation was also conducted to obtain information on the relation of the free surface with the inner flow. In the simulation, the model included from a two-staged contraction nozzle to a flow channel with a free surface flow region and simulation results were compared with the experimental data. (author)

78 FR 22872 - Hamilton Street Hydro, LLC; Notice of Preliminary Permit Application Accepted for Filing and...

Science.gov (United States)

2013-04-17

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Project No. 14499-000] Hamilton Street... Project would consist of the following: (1) An existing 20-foot-high concrete gravity dam with a 690-foot-long spillway; (2) an existing impoundment having a surface area of 300 acres and a storage capacity of...

43 CFR 23.8 - Approval of mining plan.

Science.gov (United States)

2010-10-01

... to enter any receiving waters; (5) A design for the necessary impoundment, treatment or control of... prevent the pollution of receiving waters; (6) A description of measures to be taken to prevent or control fire, soil erosion, pollution of surface and ground water, damage to fish and wildlife, and hazards to...

40 CFR 265.1081 - Definitions.

Science.gov (United States)

2010-07-01

... captured vapors through a closed-vent system to a control device. External floating roof means a pontoon... move with fluctuations in the level of the material managed in the unit. Floating membrane cover means... hazardous waste being managed in a surface impoundment. Floating roof means a cover consisting of a double...

Air/Superfund National Technical Guidance Study Series. Data Base of emission-rate-measurement projects. Technical note

Energy Technology Data Exchange (ETDEWEB)

Eklund, B.; Petrinec, C.; Ranum, D.; Howlett, L.

1991-06-01

A compilation and evaluation of Volatile Organic Compound (VOC) emission rate data was performed. The three primary objectives were (1) to determine typical averages and ranges of emissions for various types of sources; (2) to determine the degree of correlation between emission rate results from different sampling methods; and (3) to examine the effects of different variables on measured emission rates. Emission rate data are presented for 33 studies covering 13 types of emission sources. The sources include landfills, surface impoundments, waste water treatment systems, leaking underground storage tanks, soil piles and landfarms. The emission rate data were obtained by using the Emission Isolation Flux Chamber, Downhole Emissions Isolation Flux Chamber, the Concentration Profile method and the Transect method. For each source, the total non-methane hydrocarbon and benzene emission rates are reported along with three other compounds that had the highest emission rate. Source concentration data (e.g. concentration in soil or waste water) are also reported for comparison to the measured emission rates.

Studies of surface states in zinc oxide nanopowders

Science.gov (United States)

Peters, Raul Mugabe

The surface of ZnO semiconductor nanosystems is a key performance-defining factor in numerous applications. In this work we present experimental results for the surface defect-related properties of ZnO nanoscale systems. Surface photovoltage spectroscopy was used to determine the defect level energies within the band gap, the conduction vs. valence band nature of the defect-related transitions, and to probe key dynamic parameters of the surface on a number of commercially available ZnO nanopowders. In our experimental setup, surface photovoltage characterization is conducted in high vacuum in tandem with in situ oxygen remote plasma treatments. Surface photovoltage investigations of the as-received and plasma-processed samples revealed a number of common spectral features related to surface states. Furthermore, we observed significant plasma-induced changes in the surface defect properties. Ex situ positron annihilation and photoluminescence measurements were performed on the studied samples and correlated with surface photovoltage results. The average positron lifetimes were found to be substantially longer than in a bulk single crystalline sample, which is consistent with the model of grains with defect-rich surface and subsurface layers. Compression of the powders into pellets yielded reduction of the average positron lifetimes. Surface photovoltage, positron annihilation, and photoluminescence spectra consistently showed sample-to-sample differences due to the variation in the overall quality of the nanopowders, which partially obscures observation of the scaling effects. However, the results demonstrated that our approach is efficient in detecting specific surface states in nanoscale ZnO specimens and in elucidating their nature.

Theoretical study of fractal growth and stability on surface

DEFF Research Database (Denmark)

Dick, Veronika V.; Solov'yov, Ilia; Solov'yov, Andrey V.

2009-01-01

We perform a theoretical study of the fractal growing process on surface by using the deposition, diffusion, aggregation method. We present a detailed analysis of the post-growth processes occurring in a nanofractal on surface. For this study we developed a method which describes the internal...... dynamics of particles in a fractal and accounts for their diffusion and detachment. We demonstrate that these kinetic processes are responsible for the formation of the final shape of the islands on surface after the post-growth relaxation....

An experimental study on decontamination by surface condition

International Nuclear Information System (INIS)

Lee, Young Hae

1974-01-01

Surface decontamination is one of the very important problem to be completely solved in the isotope laboratory where there is always the possibility of radioactive contamination, i.e., on the floors, walls, working tables and benches etc., Isotope laboratories require surface covering of material which can be easily and effectively decontaminated. These experiment were done to find an effective decontamination procedure for kind of surfaces which usually are found in radioisotope laboratories and the best type of surface material, that is, one which is easily decontaminated from the point of view of radiation health and safely. This study is presented to guide radioisotope laboratories in Korea which may need to renovate existing unsafe facilities. In some contaminated facilities entirely new installations may be required. Twelve types of surface material are used for study in this experiment. These include 10 cm square of stainless steel, aluminum, ceramic and mosaic tiles, glass, acrylic, formica board, asphalt tile and coated wood with 4 kinds of paints. Stepwise decontamination was performed with various decontamination procedures following a spill of I 1 31 on the center of the surface material being tested. Twelve different decontamination procedures were tested. These included wet wiping with water and detergent, or dry wiping, or removing with gummed paper. Additional chemical procedures used 10% solution of hydrochloric acid, or surface acid, or ammonium citrate, or potassium iodide, or acetone or carbon tetrachloride. The final testing method was abrasion of the test surfaces. Brief analysis of experimental results on the decontaminability on the tested surface showed: 1. Metallic surfaces such as stainless steel or aluminum, or glass, or a piece of ceramic tile or acrylic are recommended as the surface materials for isotope laboratories because these are easily decontaminated by wet wiping only. 2. Formica board, asphalt tile and wood are not easily

Atomic structure of the SbCu surface alloy: A surface X-ray diffraction study

DEFF Research Database (Denmark)

Meunier, I.; Gay, J.M.; Lapena, L.

1999-01-01

The dissolution at 400 degrees C of an antimony layer deposited at room temperature on a Cu(111) substrate leads to a surface alloy with a p(root 3x root 3)R 30 degrees x 30 degrees superstructure and a Sb composition of 1/3.We present here a structural study of this Sb-Cu compound by surface X...

X-ray scattering studies of surfaces and interfaces

International Nuclear Information System (INIS)

Sanyal, M.K.

1998-01-01

Here we shall briefly review the basics and some applications of x-ray specular reflectivity and diffuse scattering techniques. These x-ray scattering techniques are uniquely suited to study of the structure of surfaces and interfaces at atomic resolutions as they are nondestructive and can probe even interfaces which are buried. The study of structure of surfaces and interfaces is not only required in understanding physics in reduced dimensions but is also essential in developing technologically important materials

Stereophotogrammetric study of surface topography in ion irradiated silver

International Nuclear Information System (INIS)

Sokolov, V.N.; Fayazov, I.M.

1993-01-01

The irradiated surface topography of polycrystalline silver was studied using the stereophotogrammetric method. The surface of silver was irradiated with 30 keV argon ions at variation for the ion incidence angle in interval of 0-80 deg relative to a surface normal. The influence of the inclination angle of the sample in the SEM on the cone shape of a SEM-picture of the irradiated surface is discussed. The parameters of cones on the irradiated surface of silver were measured by the SEM-stereomethod. The measurements of the sample section perpendicular to the incidence plane are also carried out

Chloride ion-dependent surface-enhanced Raman scattering study of biotin on the silver surface

International Nuclear Information System (INIS)

Liu Fangfang; Gu Huaimin; Yuan Xiaojuan; Dong Xiao; Lin Yue

2011-01-01

In the present paper, the surface enhanced Raman scattering (SERS) technique was employed to study the SERS spectra of biotin molecules formed on the silver surface. The adsorption geometries of biotin molecules on the silver surface were analyzed based on the SERS data. It can be found that most vibration modes show a Raman shift in silver sol after the addition of sodium chloride solution. In addition, The Raman signals of biotin become weaker and weaker with the increase of the concentration of sodium chloride. This may be due to that the interaction between chloride ions and silver particles is stronger than the interaction between biotin molecules and silver particles. When the concentration of sodium chloride in silver colloid is higher than 0.05mol/L, superfluous chloride ions may form an absorption layer so that biotin can not be adsorbed on silver surface directly. The changes in intensity and profile shape in the SERS spectra suggest different adsorption behavior and surface-coverage of biotin on silver surface. The SERS spectra of biotin suggest that the contribution of the charge transfer mechanism to SERS may be dominant.

Temporal changes in spatial patterns of submersed macrophytes in two impounded reaches of the Upper Mississippi River, USA, 1998-2009

Science.gov (United States)

De Jager, Nathan R.; Yin, Yao

2011-01-01

We examined temporal changes in spatial patterns of submersed aquatic macrophytes during a recent three-fold increase in macrophyte abundance and in response to the cumulative effects of management actions (island construction and water level management) and changes in regional environmental conditions (turbidity) in two navigation pools of the Upper Mississippi River, Pool 8 (managed) and Pool 13 (unmanaged). We used cross-correlograms to quantify changes in the degree and range of spatial correlation between submersed macrophytes and depth across the impounded portions of the two pools from 1998-2009. Along with increases in abundance, we observed gradual expansion of submersed macrophytes into deeper water in both pools. However, we detected no temporal change in spatial patterns in Pool 13, where the range of spatial correlation was ~ 1500-2500 m in length in the downriver direction and ~ 500-1000 m in length in the crossriver direction. We initially detected similar ranges of spatial correlation in Pool 8, but over time the range of correlation in the cross river direction increased from ~ 500 m in 1998 to ~ 2000 m by 2009. Thus, the expansion of submersed macrophytes into deeper water areas in Pool 8 appears to have occurred in the cross-river direction and led to increases in patch size and a more symmetrical patch configuration. Hence, very similar temporal changes in submersed macrophyte abundance corresponded with different diffusion dynamics and spatial patterns in the two pools. We hypothesize that management actions altered spatial patterns of depth, water flow and/or wind fetch and led to the differences in spatial patterns reported here.

Ab-initio study of surface segregation in aluminum alloys

Energy Technology Data Exchange (ETDEWEB)

Qin, Yifa, E-mail: yfqin10s@imr.ac.cn; Wang, Shaoqing

2017-03-31

Highlights: • A thorough study of surface segregation energies of 41 elements in Al is performed. • Segregation energies vary periodically with the atomic numbers of impurities. • 41 elements are classified into 3 groups according to the signs of segregation energies. • The results are validated by the surface/total concentration ratio in Al alloys. - Abstract: We have calculated surface segregation energies of 41 impurities by means of density functional theory calculations. An interesting periodical variation tendency was found for surface segregation energies derived. For the majority of main group elements, segregation energies are negative which means solute elements enrichment at Al surface is energetically more favorable than uniformly dissolution. Half of transition elements possess positive segregation energies and the energies are sensitive to surface crystallographic orientations. A strong correlation is found between the segregation energies at the Al surface and the surface energ of solute elements.

40 CFR 63.1256 - Standards: Wastewater.

Science.gov (United States)

2010-07-01

... vapor managed in the surface impoundment; the effects of outdoor exposure to wind, moisture, and... drain, or install a flexible shield (or other enclosure which restricts wind motion across the open area... filled and emptied by gravity flow (i.e., there is no pump) or is operated with no more than slight...

Wildlife and the coal waste policy debate: proposed rules for coal waste disposal ignore lessons from 45 years of wildlife poisoning

Science.gov (United States)

A. Dennis Lemly; Joseph P. Skorupa

2012-01-01

This analysis examines wildlife poisoning from coal combustion waste (CCW) in the context of EPA's proposed policy that would allow continued use of surface impoundments as a disposal method. Data from 21 confirmed damage sites were evaluated, ranging from locations where historic poisoning has led to corrective actions that have greatly improved environmental...

Experimental studies of surface modified oscillating heat pipes

Science.gov (United States)

Leu, Tzong-Shyng; Wu, Cheng-Han

2017-11-01

Oscillating heat pipe (OHP) is a two-phase heat transfer device which has the characteristics of simple construction, high heat flux capability and no need of wicking structures for liquid transport. There are many studies in finding the ways how to improve the system performance OHP. In this paper, studies of the effects of contact angle ( θ c ) on the inner wall of OHP system have been conducted first. Glass OHP systems with unmodified ( θ c = 26.74°), superhydrophobic ( θ c = 156.2°), superhydrophilic ( θ c evaporator region and superhydrophobic within condensation region) surfaces, are studied. The research results indicated that thermal resistance of these four OHP systems can be significantly affected by different surface modification approaches. Although superhydrophobic OHP system can still work, the thermal resistance ( R th ) is the highest one of the four OHP systems, R th = 0.36 °C/W at 200 W. Unmodified pure glass and superhydrophilic OHP systems have similar performance. Thermal resistances are 0.28 and 0.27 °C/W at 200 W respectively. The hybrid OHP achieves the lowest thermal resistance, R th = 0.23 °C/W at 200 W in this study. The exact mechanism and effects of contact angle on OHP systems are investigated with the help of flow visualization. By comparing the flow visualization results of OHP systems before and after surface modification, one tries to find the mechanism how the surface modified inner wall surface affects the OHP system performance. In additional to the reason that the superhydrophobic dropwise condensation surface inside the hybrid OHP system, hybrid OHP system shows more stable and energetic circulation flow. It is found that instead of stratified flow, vapor slug flows are identified within the evaporator section of the hybrid OHP system that can effectively generate higher pressure force for two phase interfacial flow. This effect is attributed to be the main mechanism for better performance of the hybrid OHP system.

Microscopic Study of Surface Microtopographic Characteristics of Dental Implants

Science.gov (United States)

Sezin, M.; Croharé, L.; Ibañez, J.C.

2016-01-01

Objective: To determine and compare the micro topographic characteristics of dental implants submitted to different surface treatments, using scanning electron microscopy (SEM). Materials and Methods: Implants were divided into 7 groups of 3 specimens each, according to the surface treatment used: group 1: Osseotite, BIOMET 3i; group 2: SLA surface, Institut Straumann AG; group 3: Oxalife surface, Tree-Oss implant; group 4: B&W implant surface; group 5: Q-implant surface; group 6: ML implant surface; group 7: RBM surface, Rosterdent implant. The surfaces were examined under SEM (Carl Zeiss FE-SEM-SIGMA). Image Proplus software was used to determine the number and mean diameter of pores per area unit (mm). The data obtained were analyzed with the Mann-Whitney test. A confocal laser microscope (LEXT-OLS4100 Olympus) was used to conduct the comparative study of surface roughness (Ra). Data were analyzed using Tukey's HSD test. Results: The largest average pore diameter calculated in microns was found in group 5 (3.45 µm+/-1.91) while the smallest in group 7 (1.47µm+/-1.29). Significant differences were observed among each one of the groups studied (p<0.05). The largest number of pores/mm2 was found in group 2 (229343) and the smallest number in group 4 (10937). Group 2 showed significant differences regarding the other groups (p<0.05). The greatest roughness (Ra) was observed in group 2 (0.975µm+/-0.115) and the smallest in group 4 (0.304µm+/-0.063). Group 2 was significantly different from the other groups (p<0.05). Conclusion: The micro topography observed in the different groups presented dissimilar and specific features, depending on the chemical treatment used for the surfaces.. PMID:27335615

Defective pyrite (100) surface: An ab initio study

International Nuclear Information System (INIS)

Stirling, Andras; Bernasconi, Marco; Parrinello, Michele

2007-01-01

The structural and electronic properties of sulfur monomeric defects at the FeS 2 (100) surface have been studied by periodic density-functional calculations. We have shown that for a monomeric sulfur bound to an originally fivefold coordinated surface Fe site, the defect core features a triplet electronic ground state with unpaired spins localized on the exposed Fe-S unit. At this site, the iron and sulfur ions have oxidation states +4 and -2, respectively. This defect can be seen as produced via heterolytic bond breaking of the S-S sulfur dimer followed by a Fe-S redox reaction. The calculated sulfur 2p core-level shifts of the monomeric defects are in good agreement with experimental photoemission spectra, which allow a compelling assignment of the different spectroscopic features. The effect of water on the stability of the defective surface has also been studied, and it has been shown that the triplet state is stable against the wetting of the surface. The most important implications of the presence of the monomeric sulfur defect on the reactivity are also discussed

The passive river restoration approach as an efficient tool to improve the hydromorphological diversity of rivers - Case study from two river restoration projects in the German lower mountain range

Science.gov (United States)

Groll, M.

2017-09-01

Intensive use of European rivers during the last hundreds of years has led to profound changes in the physicochemical properties, river morphology, and aquatic faunistic communities. Rectifying these changes and improving the ecological state of all surface water bodies is the central aim of the European Water Frame Directive (WFD), and river restoration measures are the main tool to achieve this goal for many rivers. As the cost-effectiveness of all measures is crucial to the WFD implementation, the approach of the passive river restoration has become very popular over the last decades. But while costs of this approach are minimal, not much is known about the long-term effectiveness of passive river restorations. The research presented here provides essential and in-depth data about the effects of two such restoration measures on the riverbed morphology of a large river of the lower mountain region in Germany (type 9.2). More than 3200 data sets were acquired using the TRiSHa method (Typology of Riverbed Structures and Habitats). The results show a high spatial and temporal diversity and dynamic for all analyzed hydromorphologic parameters - ranging from riverbed sediments, organic structures like dead wood or macrophytes, to the distribution of 32 microhabitat types. The structures and their dynamic depend on the character of the study area (free-flowing or impounded), the location of the study sites within the research area (main channel or restored side channel), and on the occurrence of major flood events (the mapping and sampling were conducted annually from 2006 to 2008 with a 50-year flood event occurring in early 2007). These results show the potential of the passive restoration approach for creating morphologically diverse riverbeds, as habitat diversity and the spatial heterogeneity of the riverbed substrates increased significantly (e.g., more than 40% of all habitat types were only detected in the newly restored side channels). But the results also

Study on Surface Permeability of Concrete under Immersion.

Science.gov (United States)

Liu, Jun; Xing, Feng; Dong, Biqin; Ma, Hongyan; Pan, Dong

2014-01-28

In this paper, concrete specimens are immersed in ultrapure water, to study the evolutions of surface permeability, pore structure and paste microstructure following the prolonging of immersion period. According to the results, after 30-day immersion, the surface permeability of concrete becomes higher as compared with the value before immersion. However, further immersion makes the surface permeability decrease, so that the value measured after 150-day immersion is only half that measured after 30-day immersion. The early increase in surface permeability should be mainly attributed to the leaching of calcium hydroxide, while the later decrease to the refinement of pore structure due to hydration. The two effects work simultaneously and compete throughout the immersion period. The proposed mechanisms get support from microscopic measurements and observations.

Tile-based rigidization surface parametric design study

Science.gov (United States)

Giner Munoz, Laura; Luntz, Jonathan; Brei, Diann; Kim, Wonhee

2018-03-01

Inflatable technologies have proven useful in consumer goods as well as in more recent applications including civil structures, aerospace, medical, and robotics. However, inflatable technologies are typically lacking in their ability to provide rigid structural support. Particle jamming improves upon this by providing structures which are normally flexible and moldable but become rigid when air is removed. Because these are based on an airtight bladder filled with loose particles, they always occupy the full volume of its rigid state, even when not rigidized. More recent developments in layer jamming have created thin, compact rigidizing surfaces replacing the loose volume of particles with thinly layered surface materials. Work in this area has been applied to several specific applications with positive results but have not generally provided the broader understanding of the rigidization performance as a function of design parameters required for directly adapting layer rigidization technology to other applications. This paper presents a parametric design study of a new layer jamming vacuum rigidization architecture: tile-based vacuum rigidization. This form of rigidization is based on layers of tiles contained within a thin vacuum bladder which can be bent, rolled, or otherwise compactly stowed, but when deployed flat, can be vacuumed and form a large, flat, rigid plate capable of supporting large forces both localized and distributed over the surface. The general architecture and operation detailing rigidization and compliance mechanisms is introduced. To quantitatively characterize the rigidization behavior, prototypes rigidization surfaces are fabricated and an experimental technique is developed based on a 3-point bending test. Performance evaluation metrics are developed to describe the stiffness, load-bearing capacity, and internal slippage of tested prototypes. A set of experimental parametric studies are performed to better understand the impact of

Revegetation/rock cover for stabilization of inactive uranium mill tailings disposal sites

International Nuclear Information System (INIS)

Beedlow, P.A.; McShane, M.C.; Cadwell, L.L.

1982-07-01

Pacific Northwest Laboratory is developing design and performance guidelines for surface stabilization of inactive uranium mill tailings. In this work, vegetation and rock covers are being evaluated for maintaining long-term integrity of impoundment systems. Methods are being developed to estimate erosion rates associated with rock and/or vegetation covers, and to determine the effects of surface treatments on soil moisture. Interactions between surface treatments and barriers (radon and biological) are being studied as well. The product will be a set of guidelines to aid in designing surface covers. This report presents the status of this program and a discussion of considerations pertinent to the application of surface covers to tailings. Test plots located in Grand Junction, Colorado and Waterflow, New Mexico are being used to study: (1) the interactions between vegetation and radon and biological barriers, (2) the effects of surface covers on soil moisture, and (3) the effects of rock covers on vegetation

Effect of surface structure on catalytic reactions: A sum frequency generation surface vibrational spectroscopy study

International Nuclear Information System (INIS)

McCrea, Keith R.

2001-01-01

In the results discussed above, it is clear that Sum Frequency Generation (SFG) is a unique tool that allows the detection of vibrational spectra of adsorbed molecules present on single crystal surfaces under catalytic reaction conditions. Not only is it possible to detect active surface intermediates, it is also possible to detect spectator species which are not responsible for the measured turnover rates. By correlating high-pressure SFG spectra under reaction conditions and gas chromatography (GC) kinetic data, it is possible to determine which species are important under reaction intermediates. Because of the flexibility of this technique for studying surface intermediates, it is possible to determine how the structures of single crystal surfaces affect the observed rates of catalytic reactions. As an example of a structure insensitive reaction, ethylene hydrogenation was explored on both Pt(111) and Pt(100). The rates were determined to be essentially the same. It was observed that both ethylidyne and di-(sigma) bonded ethylene were present on the surface under reaction conditions on both crystals, although in different concentrations. This result shows that these two species are not responsible for the measured turnover rate, as it would be expected that one of the two crystals would be more active than the other, since the concentration of the surface intermediate would be different on the two crystals. The most likely active intermediates are weakly adsorbed molecules such as(pi)-bonded ethylene and ethyl. These species are not easily detected because their concentration lies at the detection limit of SFG. The SFG spectra and GC data essentially show that ethylene hydrogenation is structure insensitive for Pt(111) and Pt(100). SFG has proven to be a unique and excellent technique for studying adsorbed species on single crystal surfaces under high-pressure catalytic reactions. Coupled with kinetic data obtained from gas chromatography measurements, it can

The present and future on surface analysis for corrosion study

International Nuclear Information System (INIS)

Ohtsuka, Toshiaki

2015-01-01

Surface analysis for corrosion study was reviewed. For the study, the in-situ analysis was desired to describe the real feature. Light i.e., electromagnetic wave from gamma rays to infrared light has been used for the in-situ measurement of the corroded surface, although various ideas should be introduced for the study. For the application of the electromagnetic waves, a suitable window material and a suitable distance between the window and specimen surface depending on the properties of the wave must be selected. Electron spectroscopy including X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) is not applicable for the in-situ study and, however, it is very available for the corrosion study from the following points; elemental analysis, state analysis of the element, and microscopic analysis. In future, the tip enhance Raman scattering (TERS) for which the scanning probe microscopy (SPM) is combined with the surface enhanced Raman scattering (SERS) may be useful for the in-situ corrosion study. (author)

Multiple sectioning and perforation techniques for TEM sub-surface studies

International Nuclear Information System (INIS)

Lee, E.H.; Rowcliffe, A.F.

1978-01-01

Techniques for preparing multiple electron transparent regions at several depth levels below the surface of a metal disk specimen are described. These techniques are relatively rapid and find application in many areas involving surface studies. Examples are shown of multiple thin areas produced at intervals of approximately 200 nm below the original surface of a stainless steel bombarded with 4 MeV Ni +2 ions for void swelling studies

Electroreflectance and the problem of studying plasma-surface interactions

International Nuclear Information System (INIS)

Preppernau, B.L.

1995-01-01

A long standing problem in low-temperature plasma discharge physics is to understand in detail the mutual interaction of real exposed surfaces (electrodes) with the reactive plasma environment. In particular, one wishes to discern the influence of these surfaces on the plasma parameters given their contributions from secondary electrons and ions. This paper briefly reviews the known surface interaction processes as well as currently available diagnostics to study the interface between plasmas and surfaces. Next comes a discussion describing the application of plasma-modulated electroreflectance to this research and some potential experimental techniques

76 FR 29796 - Agency Information Collection Activities; Submission for OMB Review; Comment Request; Refuse...

Science.gov (United States)

2011-05-23

... for OMB Review; Comment Request; Refuse Piles and Impounding Structures, Recordkeeping and Reporting... Administration (MSHA) sponsored information collection request (ICR) titled, ``Refuse Piles and Impounding... to submit annual reports and certification on refuse piles and impoundments to the agency and to keep...

Second-harmonic and sum-frequency generation for surface studies

International Nuclear Information System (INIS)

Hunt, J.H.; Guyot-Sionnest, P.; Shen, Y.R.

1987-07-01

Second harmonic generation (SHG) has now been well established as a versatile surface-sensitive probe. It has been used to study electrochemical processes at electrode surfaces, molecular adsorption and desorption at metal and semiconductor surfaces, orientational phase transition of molecular monolayers on water, surface reconstruction and epitaxial growth, and so on. More recently, it has been employed as a tool to monitor monolayer polymerization and other surface reactions, to probe polar order of molecules at interfaces, and to measure molecular nonlinearity. While most surface techniques are restricted to the solid/vacuum environment, SHG is applicable to nearly all interfaces as long as the interfaces are accessible by light. In addition, SHG has the advantages of being capable of in-situ measurements with high temporal, spatial, and spectral resolutions

Sputter deposited bioceramic coatings: surface characterisation and initial protein adsorption studies using surface-MALDI-MS

DEFF Research Database (Denmark)

Boyd, A. R.; Burke, G. A.; Duffy, H.

2011-01-01

Protein adsorption onto calcium phosphate (Ca–P) bioceramics utilised in hard tissue implant applications has been highlighted as one of the key events that influences the subsequent biological response, in vivo. This work reports on the use of surface-matrix assisted laser desorption ionisation...... to a combination of growth factors and lipoproteins present in serum. From the data obtained here it is evident that surface-MALDI-MS has significant utility as a tool for studying the dynamic nature of protein adsorption onto the surfaces of bioceramic coatings, which most likely plays a significant role...

Modelling of contaminant release from a uranium mine tailings site

International Nuclear Information System (INIS)

Kahnt, Rene; Metschies, Thomas

2007-01-01

Available in abstract form only. Full text of publication follows: Uranium mining and milling continuing from the early 1960's until 1990 close to the town of Seelingstaedt in Eastern Germany resulted in 4 tailings impoundments with a total tailings volume of about 105 Mio. m 3 . Leakage from these tailings impoundments enters the underlying aquifers and is discharged into surface water streams. High concentration of salts, uranium and several heavy metals are released from the tailings. At present the tailings impoundments are reshaped and covered. For the identification of suitable remediation options predictions of the contaminant release for different remediation scenarios have to be made. A compartment model representing the tailings impoundments and the surrounding aquifers for the calculation of contaminant release and transport was set up using the software GOLDSIM. This compartment model describes the time dependent hydraulic conditions within the tailings and the surrounding aquifers taking into account hydraulic and geotechnical processes influencing the hydraulic properties of the tailings material. A simple geochemical approach taking into account sorption processes as well as retardation by applying a k d -approach was implemented to describe the contaminant release and transport within the hydraulic system. For uranium as the relevant contaminant the simple approach takes into account additional geochemical conditions influencing the mobility. Alternatively the model approach allows to include the results of detailed geochemical modelling of the individual tailings zones which is than used as source term for the modelling of the contaminant transport in the aquifer and to the receiving streams. (authors)

Experimental Study in Taguchi Method on Surface Quality Predication of HSM

Science.gov (United States)

Ji, Yan; Li, Yueen

2018-05-01

Based on the study of ball milling mechanism and machining surface formation mechanism, the formation of high speed ball-end milling surface is a time-varying and cumulative Thermos-mechanical coupling process. The nature of this problem is that the uneven stress field and temperature field affect the machined surface Process, the performance of the processing parameters in the processing interaction in the elastic-plastic materials produced by the elastic recovery and plastic deformation. The surface quality of machining surface is characterized by multivariable nonlinear system. It is still an indispensable and effective method to study the surface quality of high speed ball milling by experiments.

77 FR 50682 - KC Scoby Hydro, LLC; Notice of Preliminary Permit Application Accepted for Filing and Soliciting...

Science.gov (United States)

2012-08-22

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Project No. 14423-000] KC Scoby Hydro... concrete gravity dam with a 183-foot-long spillway; (2) an existing impoundment having a surface area of 22 acres and a storage capacity of 52 acre-feet at an elevation of 1,080 feet mean sea level (msl); (3) a...

Surface-ionization field mass-spectrometry studies of nonequilibrium surface ionization

International Nuclear Information System (INIS)

Blashenkov, Nikolai M; Lavrent'ev, Gennadii Ya

2007-01-01

The ionization of polyatomic molecules on tungsten and tungsten oxide surfaces is considered for quasiequilibrium or essentially nonequilibrium conditions (in the latter case, the term nonequilibrium surface ionization is used for adsorbate ionization). Heterogeneous reactions are supposed to proceed through monomolecular decay of polyatomic molecules or fragments of multimolecular complexes. The nonequilibrium nature of these reactions is established. The dependences of the current density of disordered ions on the surface temperature, electric field strength, and ionized particle energy distribution are obtained in analytical form. Heterogeneous dissociation energies, the ionization potentials of radicals, and the magnitude of reaction departure from equilibrium are determined from experimental data, as are energy exchange times between reaction products and surfaces, the number of molecules in molecular complexes, and the number of effective degrees of freedom in molecules and complexes. In collecting the data a new technique relying on surface-ionization field mass-spectrometry was applied. (instruments and methods of investigation)

Transcription of Small Surface Structures in Injection Moulding - An Experimental Study

DEFF Research Database (Denmark)

Arlø, Uffe Rolf; Kjær, Erik Michael

2000-01-01

The ability to replicate the surface roughness from mold wall to the plastic part in injection moldning has many functional and cosmetic important implications from medical use to designer products. Generally the understanding of surface transcription i.e the the replication of the surface...... structure from the mould to plastic part, also relates to micro injection moulding and moulding of parts with specific micro structures on the surface such as optical parts. The present study concerns transcription of surface roughness as a function of process parameters. The study is carried out...

Transcription of Small Surface Structures in Injection Molding - an Experimental Study

DEFF Research Database (Denmark)

Arlø, Uffe Rolf; Kjær, Erik Michael

2001-01-01

The ability to replicate the surface roughness from mold wall to the plastic part in injection moldning has many functional and cosmetic important implications from medical use to designer products. Generally the understanding of surface transcription i.e the the replication of the surface...... structure from the mould to plastic part, also relates to micro injection moulding and moulding of parts with specific micro structures on the surface such as optical parts. The present study concerns transcription of surface roughness as a function of process parameters. The study is carried out...

18 CFR 12.23 - Time for filing emergency action plan.

Science.gov (United States)

2010-04-01

... begins. (2) Temporary impoundment during construction. (i) For any unconstructed project, if a temporary impoundment would be created during construction, such as through construction of temporary or permanent cofferdams or large sediment control structures, and an accident to or failure of the impounding structures...

2101-M pond closure plan. Volume 1, Revision 2

Energy Technology Data Exchange (ETDEWEB)

Izatt, R. D.; Lerch, R. E.

1993-06-01

This document describes activities for the closure of a surface impoundment (2101-M Pond) at the Hanford Site. The 2101-H Pond was initially constructed in 1953 to serve as a drainage collection area for the 2101-H Building. (Until the Basalt Waste Isolation Project (BWIP) Laboratory was constructed in the 2101-M Building in 1979--1981, the only source contributing discharge to the pond was condensate water from the 2101-H Building heating, ventilation, and air conditioning (HVAC) system. The drains for the BWIP Laboratory rooms were plumbed into a 4-in., cast-iron, low-pressure drain pipe that carries waste water from the HVAC system to the pond. During the active life of the BWIP Laboratory, solutions of dissolved barium in groundwater samples were discharged to the 2101-M Pond via the laboratory drains. As a result of the discharges, a Part A permit application was initially submitted to the Washington State Department of Ecology (Ecology) in August 1986 which designates the 2101-M Pond as a surface impoundment.

2101-M pond closure plan

International Nuclear Information System (INIS)

1993-06-01

This document describes activities for the closure of a surface impoundment (2101-M Pond) at the Hanford Site. The 2101-H Pond was initially constructed in 1953 to serve as a drainage collection area for the 2101-H Building. (Until the Basalt Waste Isolation Project (BWIP) Laboratory was constructed in the 2101-M Building in 1979--1981, the only source contributing discharge to the pond was condensate water from the 2101-H Building heating, ventilation, and air conditioning (HVAC) system. The drains for the BWIP Laboratory rooms were plumbed into a 4-in., cast-iron, low-pressure drain pipe that carries waste water from the HVAC system to the pond. During the active life of the BWIP Laboratory, solutions of dissolved barium in groundwater samples were discharged to the 2101-M Pond via the laboratory drains. As a result of the discharges, a Part A permit application was initially submitted to the Washington State Department of Ecology (Ecology) in August 1986 which designates the 2101-M Pond as a surface impoundment

Kinetic-energy functionals studied by surface calculations

DEFF Research Database (Denmark)

Vitos, Levente; Skriver, Hans Lomholt; Kollár, J.

1998-01-01

The self-consistent jellium model of metal surfaces is used to study the accuracy of a number of semilocal kinetic-energy functionals for independent particles. It is shown that the poor accuracy exhibited by the gradient expansion approximation and most of the semiempirical functionals in the lo...... density, high gradient limit may be subtantially improved by including locally a von Weizsacker term. Based on this, we propose a simple one-parameter Pade's approximation, which reproduces the exact Kohn-Sham surface kinetic energy over the entire range of metallic densities....

U-Zr alloy: XPS and TEM study of surface passivation

Science.gov (United States)

Paukov, M.; Tkach, I.; Huber, F.; Gouder, T.; Cieslar, M.; Drozdenko, D.; Minarik, P.; Havela, L.

2018-05-01

Surface reactivity of Uranium metal is an important factor limiting its practical applications. Bcc alloys of U with various transition metals are much less reactive than pure Uranium. So as to specify the mechanism of surface protection, we have been studying the U-20 at.% Zr alloy by photoelectron spectroscopy and transmission electron microscopy. The surface was studied in as-obtained state, in various stages of surface cleaning, and during an isochronal annealing cycle. The analysis based on U-4f, Zr-3p, and O-1 s spectra shows that a Zr-rich phase segregates at the surface at temperatures exceeding 550 K, which provides a self-assembled coating. The comparison of oxygen exposure of the stoichiometric and coated surfaces shows that the coating is efficiently preventing the oxidation of uranium even at elevated temperatures. The coating can be associated with the UZr2+x phase. TEM study indicated that the coating is about 20 nm thick. For the clean state, the U-4f core-level lines of the bcc alloy are practically identical to those of α-U, revealing similar delocalization of the 5f electronic states.

Hydrogeologic data for the Big River-Mishnock River stream-aquifer system, central Rhode Island

Science.gov (United States)

Craft, P.A.

2001-01-01

Hydrogeology, ground-water development alternatives, and water quality in the BigMishnock stream-aquifer system in central Rhode Island are being investigated as part of a long-term cooperative program between the Rhode Island Water Resources Board and the U.S. Geological Survey to evaluate the ground-water resources throughout Rhode Island. The study area includes the Big River drainage basin and that portion of the Mishnock River drainage basin upstream from the Mishnock River at State Route 3. This report presents geologic data and hydrologic and water-quality data for ground and surface water. Ground-water data were collected from July 1996 through September 1998 from a network of observation wells consisting of existing wells and wells installed for this study, which provided a broad distribution of data-collection sites throughout the study area. Streambed piezometers were used to obtain differences in head data between surface-water levels and ground-water levels to help evaluate stream-aquifer interactions throughout the study area. The types of data presented include monthly ground-water levels, average daily ground-water withdrawals, drawdown data from aquifer tests, and water-quality data. Historical water-level data from other wells within the study area also are presented in this report. Surface-water data were obtained from a network consisting of surface-water impoundments, such as ponds and reservoirs, existing and newly established partial-record stream-discharge sites, and synoptic surface-water-quality sites. Water levels were collected monthly from the surface-water impoundments. Stream-discharge measurements were made at partial-record sites to provide measurements of inflow, outflow, and internal flow throughout the study area. Specific conductance was measured monthly at partial-record sites during the study, and also during the fall and spring of 1997 and 1998 at 41 synoptic sites throughout the study area. General geologic data, such as

Sealing layer of fly ashes and sewage sludge and vegetation establishment in treatment of mine tailings impoundments; Flygaska och roetslam som taetskikt vid efterbehandling av sandmagasin med vegetationsetablering

Energy Technology Data Exchange (ETDEWEB)

Greger, Maria; Neuschuetz, Clara [Stockholm Univ. (Sweden). Dept. of Botany; Isaksson, Karl-Erik [Boliden Mineral AB (Sweden)

2006-02-15

Each year the Swedish mining industry produces 25 Mtonnes of mine tailings that are disposed of in extensive natural impoundments. As this sand, containing more or less sulphide-rich minerals, is penetrated by oxygen and water, it starts weathering resulting in formation of acidic and metal-rich drainage water. To prevent oxygen penetration the mine tailings can be covered with a sealing layer covered with a protective cover that facilitates establishment of vegetation. The aim of this study has been to examine the function of fly ash and sewage sludge in sealing layers at impoundments of pyrite rich mine tailings, and the ability of different plant species, which are suitable for establishment in these areas, to penetrate the sealing layer with their roots and what impact they have on the drainage water. Experiments have been performed in field and greenhouse environment, with sealing layers consisting of fly ash and sewage sludge mixtures, covered with protective covers of sewage sludge or till. Plant establishment has been studied in a survey of naturally established plants at sewage sludge disposal sites close to mining areas, and by sowing and planting of selected plants, for instance fast growing grass species and fibre hemp at the test plots in field and in greenhouse experiments. Large scale application of ashes, sewage sludge and an ash/sludge mixture have been performed in field at three test plots with the size of 0.3-1 ha. Leakage of nutrients and metals from sealing layers has been studied in field and greenhouse tests. In addition, the ability of plant roots to penetrate sealing layers made of different ash/sludge mixtures have been examined in greenhouse experiments. This investigation is a cooperation between Stockholm University and Boliden Mineral AB, and the field experiments have been performed at the mine tailings impoundments at Gillervattnet, Boliden. Other collaborating participants are Skellefteaa Kraft and Munksund, who have produced the

Surface reactivity of mercury on the oxygen-terminated hematite(0001) surface: a first-principle study

Science.gov (United States)

Jung, J. E.; Wilcox, J.

2016-12-01

Hematite (α-Fe2O3) is a common mineral found in Earth's near-surface environment. Due to its nontoxicity, corrosion-resistance, and high thermal stability, α-Fe2O3 has attracted attentions as materials for various applications such as photocatalysts, gas sensors, as well as for the removal of heavy metals. In this study, α-Fe2O3 is chosen for potential mercury (Hg) sorbent in order to remove Hg from coal-fired power plants. Specifically, theoretical approaches using density functional theory (DFT) is used to understand surface reactivity of Hg on oxygen (O) terminated α-Fe2O3(0001) surface. The most probable adsorption sites of Hg, chlorine (Cl), and mercury chloride (HgCl) on the α-Fe2O3 surface are found based on adsorption energy calculations, and the oxidation states of the adsorbates are determined by Bader charge analysis. Additionally, projected density of states (PDOS) analysis characterizes the surface-adsorbate bonding mechanism. The results of adsorption energy calculation proposes that Hg physisorbs to the α-Fe2O3(0001) surface with adsorption energy of -0.278 eV, and the subsequent Bader charge analysis confirms that Hg is slightly oxidized. In addition, Cl introduced to the Hg-adsorbed surface strengthens Hg stability on the α-Fe2O3(0001) surface as evidenced by a shortened Hg-surface equilibrium distance. The PDOS analysis also suggests that Cl enhances the chemical bonding between the surface and the adsorbate, thereby increasing adsorption strength. In summary, α-Fe2O3 has ability to adsorb and oxidize Hg, and this reactivity is enhanced in the presence of Cl.

Fermi surface study of CeSb

International Nuclear Information System (INIS)

Aoki, H.; Crabtree, G.W.; Joss, W.; Hulliger, F.

1984-09-01

A Fermi surface study of the ferromagnetic phase of CeSb is presented. The γ frequency branches arising from the electron surfaces at the X points, three separate frequency branches from the hole surfaces at the GAMMA point and the low frequency branch α have been observed. The effective mass ratios are low and range from approx. 0.2 for the α branch to approx. 1.0 for the high frequency branch of γ. The low effective mass ratios suggest that the admixture of the conduction states with the f state is small. We have observed a drastic change in the appearance of the dHvA signal at the phase transition between the ferromagnetic and lower field antiferromagnetic phases: The low frequency α oscillation suddenly disappears as the crystal enters the antiferromagnetic phase. By utilizing the change in the signal appearance, the transition field strength has been measured as a function of the field direction. The present experimental results, particularly the origin of the α oscillation, are discussed in the light of the p-f mixing theory and recent band structure calculations based on localized f orbitals

Fermi surface study of CeSb

International Nuclear Information System (INIS)

Aoki, H.; Crabtree, G.; Joss, W.; Hulliger, F.

1985-01-01

A Fermi surface study of the ferromagnetic phase of CeSb is presented. The γ frequency branches arising from the electron surfaces at the X points, three separate frequency branches from the hole surfaces at the GAMMA point, and the low-frequency branch α have been observed. The effective mass ratios are low and range from approx.0.2 for the α branch to approx.1.0 for the high-frequency branch of γ. The low effective mass ratios suggest that the admixture of the conduction states with the f state is small. We have observed a drastic change in the appearance of the de Haas--van Alpen signal at the phase transition between the ferromagnetic and lower field antiferromagnetic phases: the low-frequency α oscillation suddenly disappears as the crystal enters the antiferromagnetic phase. By utilizing the change in the signal appearance, the transition field strength has been measured as a function of the field direction. The present experimental results particularly the origin of the α oscillation, are discussed in the light of the p-f mixing theory and recent band-structure calculations based on localized f orbitals

Studies of nanosecond pulse surface ionization wave discharges over solid and liquid dielectric surfaces

International Nuclear Information System (INIS)

Petrishchev, Vitaly; Leonov, Sergey; Adamovich, Igor V

2014-01-01

Surface ionization wave discharges generated by high-voltage nanosecond pulses, propagating over a planar quartz surface and over liquid surfaces (distilled water and 1-butanol) have been studied in a rectangular cross section test cell. The discharge was initiated using a custom-made, alternating polarity, high-voltage nanosecond pulse plasma generator, operated at a pulse repetition rate of 100–500 Hz, with a pulse peak voltage and current of 10–15 kV and 7–20 A, respectively, a pulse FWHM of ∼100 ns, and a coupled pulse energy of 2–9 mJ/pulse. Wave speed was measured using a capacitive probe. ICCD camera images demonstrated that the ionization wave propagated predominantly over the quartz wall or over the liquid surface adjacent to the grounded waveguide placed along the bottom wall of the test cell. Under all experimental conditions tested, the surface plasma ‘sheet’ was diffuse and fairly uniform, both for positive and negative polarities. The parameters of ionization wave discharge propagating over distilled water and 1-butanol surfaces were close to those of the discharge over a quartz wall. No perturbation of the liquid surface by the discharge was detected. In most cases, the positive polarity surface ionization wave propagated at a higher speed and over a longer distance compared to the negative polarity wave. For all three sets of experiments (surface ionization wave discharge over quartz, water and 1-butanol), wave speed and travel distance decreased with pressure. Diffuse, highly reproducible surface ionization wave discharge was also observed over the liquid butanol–saturated butanol vapor interface, as well as over the distilled water–saturated water vapor interface, without buffer gas flow. No significant difference was detected between surface ionization discharges sustained using single-polarity (positive or negative), or alternating polarity high-voltage pulses. Plasma emission images yielded preliminary evidence of charge

hydrogeological map of kabo sheet 80 nw topographical sheet 1

African Journals Online (AJOL)

DR. AMINU

runoff average of 216,240,192m3/a and mean base flow of 114,455m3/a, and surface runoff mean of 159, 228,113m3/a, also ... Key words: Hydro geological maps, Configurations maps, Hydro years, Base flow, Coefficient of base flow and Hydraulic ..... impounding reservoirs of four earth fill dams (colloquially called dams) ...

Environmental Compliance Assessment System (ECAS)

Science.gov (United States)

1993-09-01

generators -open burning/open detonation -peak shaving generators -landfills -turbines -surface impoundments -landfarw r- bioremediation Petroleum Product...greater. Methidathion All formu- All uses Restricted Residue effects lations. except on avian species. stock, safflower, and sunflower . All formu...Nursery Unclassified lations. stock. safflower, and sunflower Methomyl As sole Nondomestic Restricted. Residue effects active in- outdoor on mammalian

Geochemical behavior of uranium mill tailings leachate in the subsurface

International Nuclear Information System (INIS)

Brookins, D.G.

1993-01-01

Leachate generated from surface disposal of acidic uranium mill tailings at Maybell, CO has impacted groundwater quality within the underlying mineralized Browns Park Formation. The extent of groundwater contamination, however, is located directly beneath the tailings impoundment. The milling process consisted of sulfuric acid extraction of uranium from the feed ore by a complex chemical leaching and precipitation process. Tailings leachate at the site contains elevated concentrations of Al, As, Cd, Mo, Ni, NO 3 , Se, U, and other solutes. From column leach tests, the concentrations of contaminants within tailings pore fluid are SO 4 >NH 4 >NO 3 >U>Se>Ni>As>Cd at pH 4.0. The carbonate buffering capacity of the tailings subsoil has decreased because of calcite dissolution in the presence of acidic leachate. Groundwater quality data, mineralogical and microbiological studies, and geochemical modeling suggest that As, NO 3 , Se, U and other solutes are being removed from solution through precipitation, adsorption, and denitrification processes under reducing conditions. Presence of hydrogen sulfide, liquid and gaseous hydrocarbons, dissolved organic, and abundant pyrite within the Browns Park Formations have maintained reducing conditions subjacent to the tailings impoundment. Groundwater is in close equilibrium with coffinite and uraninite, the primary U(IV) minerals extracted from the Browns Parks Formation. Denitrifying bacteria identified in this study catalyze redox reactions involving NO 3 . Subsequently, contaminant distributions of NO 3 decrease 1000 times beneath the tailings impoundment. Applying geochemical and biochemical processes occurring at Maybell provides an excellent model for in situ aquifer restoration programs considered at other uranium tailings and heavy-metal-mixed waste contaminated sites. (author) 4 figs., 4 tabs., 27 refs

Evaluation of surface water treatment and discharge options for the Weldon Spring Site Remedial Action Project

International Nuclear Information System (INIS)

Goyette, M.L.; MacDonell, M.M.

1992-01-01

The US Department of Energy (DOE), under its Environmental Restoration and Waste Management Program, is responsible for conducting response actions at the Weldon Spring site in St. Charles County, Missouri. The site consists of two noncontiguous areas: (1) the chemical plant area, which includes four raffinate pits and two small ponds, and (2) a 3.6-ha (9-acre) quarry located about 6.4 km (4 mi) southwest of the chemical plant area. Both of these areas became chemically and radioactively contaminated as a result of processing and disposal activities that took place from the 1940s through 1960s. The Weldon Spring site, located about 48 km (30 mi) west of St. Louis, is listed on the National Priorities List of the US Environmental Protection Agency. Nitroaromatic explosives were processed by the Army at the chemical plant area during the 1940s, and radioactive materials were processed by DOE's predecessor agency (the Atomic Energy Commission) during the 1950s and 1960s. Overall remediation of the Weldon Spring site is being addressed through the Weldon Spring Site Remedial Action Project, and it consists of several components. One component is the management of radioactively and chemically contaminated surface water impoundments at the chemical plant area -- i.e., the four raffinate pits, Frog Pond, and Ash Pond which was addressed under a separate action and documented in an engineering evaluation/cost analysis report. This report discusses the evaluation of surface water treatment at the Weldon Spring site

Dedicated detectors for surface studies by Moessbauer spectroscopy

International Nuclear Information System (INIS)

Bibicu, I.; Rogalski, M.S.; Nicolescu, G.

2001-01-01

Moessbauer spectroscopy is a nuclear resonance method largely utilized in solid state studies. Following resonant nuclear absorption, gamma radiations, conversion X-rays, conversion or Auger electrons are emitted. By detection of gamma radiations information about the sample as a whole are obtained while by detection of electrons or X radiation one obtains data on the surface layer. Our laboratory was among the firsts to produce and use flow gas proportional detectors for surface studies by Moessbauer spectroscopy. Four types of detectors were devised: - detectors for electron detection (90% He + 10% CH 4 ); - detectors for conversion X-ray detection (90% Ar + 10% CH 4 ); - detectors for electrons or internal conversion X rays; - detectors for simultaneous detection of electrons and conversion X rays emitted from the same source. All detectors allow simultaneous Moessbauer measurements both for surface and volume for a given sample. Details of construction are presented for the four types of detectors

Glass transition near the free surface studied by synchrotron radiation

Energy Technology Data Exchange (ETDEWEB)

Sikorski, M.

2008-06-15

A comprehensive picture of the glass transition near the liquid/vapor interface of the model organic glass former dibutyl phthalate is presented in this work. Several surface-sensitive techniques using x-ray synchrotron radiation were applied to investigate the static and dynamic aspects of the formation of the glassy state from the supercooled liquid. The amorphous nature of dibutyl phthalate close to the free surface was confirmed by grazing incidence X-ray diffraction studies. Results from X-ray reflectivity measurements indicate a uniform electron density distribution close to the interface excluding the possibility of surface freezing down to 175 K. Dynamics on sub-{mu}m length-scales at the surface was studied with coherent synchrotron radiation via x-ray photon correlation spectroscopy. From the analysis of the dispersion relation of the surface modes, viscoelastic properties of the dibutyl phthalate are deduced. The Kelvin-Voigt model of viscoelastic media was found to describe well the properties of the liquid/vapor interface below room temperature. The data show that the viscosity at the interface matches the values reported for bulk dibutyl phthalate. The scaled relaxation rate at the surface agrees with the bulk data above 210 K. Upon approaching the glass transition temperature the free surface was observed to relax considerably faster close to the liquid/vapor interface than in bulk. The concept of higher relaxation rate at the free surface is also supported by the results of the quasielastic nuclear forward scattering experiment, during which dynamics on molecular length scales around the calorimetric glass transition temperature is studied. The data were analyzed using mode-coupling theory of the glass transition and the model of the liquid(glass)/vapor interface, predicting inhomogeneous dynamics near the surface. The quasielastic nuclear forward scattering data can be explained when the molecular mobility is assumed to decrease with the increasing

Glass transition near the free surface studied by synchrotron radiation

International Nuclear Information System (INIS)

Sikorski, M.

2008-06-01

A comprehensive picture of the glass transition near the liquid/vapor interface of the model organic glass former dibutyl phthalate is presented in this work. Several surface-sensitive techniques using x-ray synchrotron radiation were applied to investigate the static and dynamic aspects of the formation of the glassy state from the supercooled liquid. The amorphous nature of dibutyl phthalate close to the free surface was confirmed by grazing incidence X-ray diffraction studies. Results from X-ray reflectivity measurements indicate a uniform electron density distribution close to the interface excluding the possibility of surface freezing down to 175 K. Dynamics on sub-μm length-scales at the surface was studied with coherent synchrotron radiation via x-ray photon correlation spectroscopy. From the analysis of the dispersion relation of the surface modes, viscoelastic properties of the dibutyl phthalate are deduced. The Kelvin-Voigt model of viscoelastic media was found to describe well the properties of the liquid/vapor interface below room temperature. The data show that the viscosity at the interface matches the values reported for bulk dibutyl phthalate. The scaled relaxation rate at the surface agrees with the bulk data above 210 K. Upon approaching the glass transition temperature the free surface was observed to relax considerably faster close to the liquid/vapor interface than in bulk. The concept of higher relaxation rate at the free surface is also supported by the results of the quasielastic nuclear forward scattering experiment, during which dynamics on molecular length scales around the calorimetric glass transition temperature is studied. The data were analyzed using mode-coupling theory of the glass transition and the model of the liquid(glass)/vapor interface, predicting inhomogeneous dynamics near the surface. The quasielastic nuclear forward scattering data can be explained when the molecular mobility is assumed to decrease with the increasing

Structure and reactivity of heterogeneous surfaces and study of the geometry of surface complexes. Progress report, January 1, 1984-December 31, 1984

International Nuclear Information System (INIS)

Landman, U.

1984-01-01

Since the beginning of this project, our group has been involved in theoretical studies of surface phenomena and processes, aimed toward increasing our understanding of fundamental processes which govern the properties of material surfaces. Our studies cover a wide spectrum of surface phenomena: surface reactivity, surface crystallography, electronic and vibrational structure, dynamical processes, phase transformations and phase change, the properties of interfaces and investigations of material processing and novel materials preparation techniques. In these investigations we develop and employ analytical and novel numerical, simulation, methods for the study of complex surface phenomena. Our recent surface molecular dynamics studies and simulations of laser annealing phenomena opened new avenues for the investigation of the microscopic dynamics and evolution of equilibrium and non-equilibrium processes at surfaces and interfaces. Our current studies of metallic glasses using a new langrangian formulation which includes all components of the total energy (density dependent electron gas, single particle and pair interactions) of the system, represents a novel approach for theoretical studies of this important class of systems

Use of surface electromyography in phonation studies: an integrative review

Science.gov (United States)

Balata, Patricia Maria Mendes; Silva, Hilton Justino da; Moraes, Kyvia Juliana Rocha de; Pernambuco, Leandro de Araújo; Moraes, Sílvia Regina Arruda de

2013-01-01

Summary Introduction: Surface electromyography has been used to assess the extrinsic laryngeal muscles during chewing and swallowing, but there have been few studies assessing these muscles during phonation. Objective: To investigate the current state of knowledge regarding the use of surface electromyography for evaluation of the electrical activity of the extrinsic muscles of the larynx during phonation by means of an integrative review. Method: We searched for articles and other papers in the PubMed, Medline/Bireme, and Scielo databases that were published between 1980 and 2012, by using the following descriptors: surface electromyography and voice, surface electromyography and phonation, and surface electromyography and dysphonia. The articles were selectedon the basis ofinclusion and exclusion criteria. Data Synthesis: This was carried out with a cross critical matrix. We selected 27 papers,i.e., 24 articles and 3 theses. The studies differed methodologically with regards to sample size and investigation techniques, making it difficult to compare them, but showed differences in electrical activity between the studied groups (dysphonicsubjects, non-dysphonicsubjects, singers, and others). Conclusion: Electromyography has clinical applicability when technical precautions with respect to application and analysis are obeyed. However, it is necessary to adopt a universal system of assessment tasks and related measurement techniques to allow comparisons between studies. PMID:25992030

Use of surface electromyography in phonation studies: an integrative review

Directory of Open Access Journals (Sweden)

Balata, Patricia Maria Mendes

2014-01-01

Full Text Available Introduction: Surface electromyography has been used to assess the extrinsic laryngeal muscles during chewing and swallowing, but there have been few studies assessing these muscles during phonation. Objective: To investigate the current state of knowledge regarding the use of surface electromyography for evaluation of the electrical activity of the extrinsic muscles of the larynx during phonation by means of an integrative review. Method: We searched for articles and other papers in the PubMed, Medline/Bireme, and Scielo databases that were published between 1980 and 2012, by using the following descriptors: surface electromyography and voice, surface electromyography and phonation, and surface electromyography and dysphonia. The articles were selectedon the basis ofinclusion and exclusion criteria. Data Synthesis: This was carried out with a cross critical matrix. We selected 27 papers,i.e., 24 articles and 3 theses. The studies differed methodologically with regards to sample size and investigation techniques, making it difficult to compare them, but showed differences in electrical activity between the studied groups (dysphonicsubjects, non-dysphonicsubjects, singers, and others. Conclusion: Electromyography has clinical applicability when technical precautions with respect to application and analysis are obeyed. However, it is necessary to adopt a universal system of assessment tasks and related measurement techniques to allow comparisons between studies.

Windblown Dust Deposition Forecasting and Spread of Contamination around Mine Tailings.

Science.gov (United States)

Stovern, Michael; Guzmán, Héctor; Rine, Kyle P; Felix, Omar; King, Matthew; Ela, Wendell P; Betterton, Eric A; Sáez, Avelino Eduardo

2016-02-01

Wind erosion, transport and deposition of windblown dust from anthropogenic sources, such as mine tailings impoundments, can have significant effects on the surrounding environment. The lack of vegetation and the vertical protrusion of the mine tailings above the neighboring terrain make the tailings susceptible to wind erosion. Modeling the erosion, transport and deposition of particulate matter from mine tailings is a challenge for many reasons, including heterogeneity of the soil surface, vegetative canopy coverage, dynamic meteorological conditions and topographic influences. In this work, a previously developed Deposition Forecasting Model (DFM) that is specifically designed to model the transport of particulate matter from mine tailings impoundments is verified using dust collection and topsoil measurements. The DFM is initialized using data from an operational Weather Research and Forecasting (WRF) model. The forecast deposition patterns are compared to dust collected by inverted-disc samplers and determined through gravimetric, chemical composition and lead isotopic analysis. The DFM is capable of predicting dust deposition patterns from the tailings impoundment to the surrounding area. The methodology and approach employed in this work can be generalized to other contaminated sites from which dust transport to the local environment can be assessed as a potential route for human exposure.

An overview of surface radiance and biology studies in FIFE

Science.gov (United States)

Blad, B. L.; Schimel, D. S.

1992-01-01

The use of satellite data to study and to understand energy and mass exchanges between the land surface and the atmosphere requires information about various biological processes and how various reflected or emitted spectral radiances are influenced by or manifested in these processes. To obtain such information, studies were conducted by the First ISLSCP Field Experiment (FIFE) surface radiances and biology (SRB) group using surface, near-surface, helicopter, and aircraft measurements. The two primary objectives of this group were to relate radiative fluxes to biophysical parameters and physiological processes and to assess how various management treatments affect important biological processes. This overview paper summarizes the results obtained by various SRB teams working in nine different areas: (1) measurements of bidirectional reflectance and estimation of hemispherical albedo; (2) evaluation of spatial and seasonal variability reflectance and vegetation indices; (3) determination of surface and radiational factors and their effects on vegetation indices and photosynthetically active radiation relationships; (4) use of surface temperatures to estimate sensible heat flux; (5) controls over photosynthesis and respiration at small scales; (6) soil surface CO2 fluxes and grassland carbon budget; (7) landscape variations in controls over gas exchange and energy partitioning; (8) radiometric response of prairie to management and topography; and (9) determination of nitrogen gas exchanges in a tallgrass prairie.

An overview of surface radiance and biology studies in FIFE

Science.gov (United States)

Blad, B. L.; Schimel, D. S.

1992-11-01

The use of satellite data to study and to understand energy and mass exchanges between the land surface and the atmosphere requires information about various biological processes and how various reflected or emitted spectral radiances are influenced by or manifested in these processes. To obtain such information, studies were conducted by the First ISLSCP Field Experiment (FIFE) surface radiances and biology (SRB) group using surface, near-surface, helicopter, and aircraft measurements. The two primary objectives of this group were to relate radiative fluxes to biophysical parameters and physiological processes and to assess how various management treatments affect important biological processes. This overview paper summarizes the results obtained by various SRB teams working in nine different areas: (1) measurement of bidirectional reflectance and estimation of hemispherical albedo; (2) evaluation of spatial and seasonal variability of spectral reflectance and vegetation indices; (3) determination of surface and radiational factors and their effects on vegetation indices and PAR relationships; (4) use of surface temperatures to estimate sensible heat flux; (5) controls over photosynthesis and respiration at small scales; (6) soil surface CO2 fluxes and grassland carbon budget; (7) landscape variations in controls over gas exchange and energy partitioning; (8) radiometric response of prairie to management and topography; and (9) determination of nitrogen gas exchanges in a tallgrass prairie.

Study of plasma-surface interaction at the GOL-3 facility

Energy Technology Data Exchange (ETDEWEB)

Shoshin, A.A., E-mail: shoshin@mail.ru [Budker Institute of Nuclear Physics SB RAS, Novosibirsk 630090 (Russian Federation); Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Arakcheev, A.S., E-mail: asarakcheev@gmail.com [Budker Institute of Nuclear Physics SB RAS, Novosibirsk 630090 (Russian Federation); Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Arzhannikov, A.V., E-mail: A.V.Arzhannikov@inp.nsk.su [Budker Institute of Nuclear Physics SB RAS, Novosibirsk 630090 (Russian Federation); Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Burdakov, A.V., E-mail: a.v.burdakov@mail.ru [Budker Institute of Nuclear Physics SB RAS, Novosibirsk 630090 (Russian Federation); Novosibirsk State Technical University, Novosibirsk 630092 (Russian Federation); Ivanov, I.A., E-mail: I.A.Ivanov@inp.nsk.su [Budker Institute of Nuclear Physics SB RAS, Novosibirsk 630090 (Russian Federation); Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Kasatov, A.A., E-mail: a.a.kasatov@gmail.com [Budker Institute of Nuclear Physics SB RAS, Novosibirsk 630090 (Russian Federation); Kuklin, K.N., E-mail: K.N.Kuklin@inp.nsk.su [Budker Institute of Nuclear Physics SB RAS, Novosibirsk 630090 (Russian Federation); Polosatkin, S.V., E-mail: S.V.Polosatkin@inp.nsk.su [Budker Institute of Nuclear Physics SB RAS, Novosibirsk 630090 (Russian Federation); Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Postupaev, V.V., E-mail: V.V.Postupaev@inp.nsk.su [Budker Institute of Nuclear Physics SB RAS, Novosibirsk 630090 (Russian Federation); Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Sinitsky, S.L., E-mail: S.L.Sinitsky@inp.nsk.su [Budker Institute of Nuclear Physics SB RAS, Novosibirsk 630090 (Russian Federation); Novosibirsk State University, Novosibirsk 630090 (Russian Federation); and others

2017-01-15

The review presents experimental studies of plasma-surface interaction and materials behavior under plasma loads done in the multiple-mirror trap of the GOL-3 facility. In the experiments for the PSI, the energy density in the extracted plasma stream varies from 0.5 to 30 MJ/m{sup 2}. Parameters of near-surface plasma measured by a set of diagnostics are reviewed. Surface patterns of targets exposed to the plasma are analyzed. The erosion depth depends on the energy loads—it rises from 0 to 600 μm at 0.5 and 30 MJ/m{sup 2}, correspondingly. Cracking and evolution of graphite and tungsten surface morphology are discussed. The enthalpy of brittle destruction of graphite (10 kJ/g), which determines the threshold of bulk damage of targets irradiated with a charged-particle flux with large penetration depth, was determined. Comparison of different facilities for PSI studies are presented. Heat flux play a key role to the target surface erosion.

First principles study of hydroxyapatite surface

Science.gov (United States)

Slepko, Alexander; Demkov, Alexander A.

2013-07-01

The biomineral hydroxyapatite (HA) [Ca10(PO4)6(OH)2] is the main mineral constituent of mammal bone. We report a theoretical investigation of the HA surface. We identify the low energy surface orientations and stoichiometry under a variety of chemical environments. The surface most stable in the physiologically relevant OH-rich environment is the OH-terminated (1000) surface. We calculate the work function of HA and relate it to the surface composition. For the lowest energy OH-terminated surface we find the work function of 5.1 eV, in close agreement with the experimentally reported range of 4.7 eV-5.1 eV [V. S. Bystrov, E. Paramonova, Y. Dekhtyar, A. Katashev, A. Karlov, N. Polyaka, A. V. Bystrova, A. Patmalnieks, and A. L. Kholkin, J. Phys.: Condens. Matter 23, 065302 (2011), 10.1088/0953-8984/23/6/065302].

Radioactive safety analysis and assessment of waste rock pile site in uranium tailings

International Nuclear Information System (INIS)

Liu Changrong; Liu Zehua; Wang Zhiyong; Zhou Xinghuo

2007-01-01

Based on theoretical calculation and in-situ test results, distribution and emissions of radioactive nuclides of uranium tailings impoundment and waste rock pile sites are analyzed in this paper. It is pointed out that 222 Rn is the main nuclide of uranium tailings impoundment and waste rock pile site. Also 222 Rn is the main source term of public dose. 222 Rn concentrations in the atmospheric environment around and individual dose to Rn gradually decrease with increasing distances to uranium tailings impoundment and waste rock pile site. Based on in-situ tests on five uranium tailings impoundment and waste rock pile sites, a decisive method and safety protection distance are presented, which can be used to guide the validation and design of radioactive safety protection in uranium tailings impoundment and waste rock pile sites. (authors)

[Study on preparation and physicochemical properties of surface modified sintered bone].

Science.gov (United States)

Li, Jingfeng; Zheng, Qixin; Guo, Xiaodong

2012-06-01

The aim of this study is to investigate a new method for preparing a biomimetic bone material-surface modified sintered bovine cancellous bone, and to improve its bioactivity as a tissue engineering bone. The prepared sintered bovine cancellous bones with the same size were randomly divided into two groups, immersing in 1 and 1. 5 times simulated body fluid (SBF), respectively. The three time periods of soak time were 7, 14, and 21 days. After sintered bone was dried, the surface morphology of sintered bone and surface mineralization composition were observed under scanning electron microscopy (SEM). By comparing the effect of surface modification of sintered bone materials, we chose the most ideal material and studied its pore size, the rate of the porosity, the compress and bend intensity. And then the material and the sintered bone material without surface modification were compared. The study indicated that sintered bone material immersed in SBF (1.5 times) for 14 days showed the best effect of surface modification, retaining the original physico-chemical properties of sintered bone.

Study on hydrophilicity of polymer surfaces improved by plasma treatment

International Nuclear Information System (INIS)

Lai Jiangnan; Sunderland, Bob; Xue Jianming; Yan, Sha; Zhao Weijiang; Folkard, Melvyn; Michael, Barry D.; Wang Yugang

2006-01-01

Surface properties of polycarbonate (PC), polypropylene (PP), polyethylene terephthalate (PET) samples treated by microwave-induced argon plasma have been studied with contact angle measurement, X-ray photoelectron spectroscopy (XPS) and scanned electron microscopy (SEM). It is found that plasma treatment modified the surfaces both in composition and roughness. Modification of composition makes polymer surfaces tend to be highly hydrophilic, which mainly depended on the increase of ratio of oxygen-containing group as same as other papers reported. And this experiment further revealed that C=O bond is Key factor to the improvement of the hydrophilicity of polymer surfaces. Our SEM observation on PET shown that the roughness of the surface has also been improved in micron scale and it has influence on the surface hydrophilicity

Polymer Adsorption on Graphite and CVD Graphene Surfaces Studied by Surface-Specific Vibrational Spectroscopy.

Science.gov (United States)

Su, Yudan; Han, Hui-Ling; Cai, Qun; Wu, Qiong; Xie, Mingxiu; Chen, Daoyong; Geng, Baisong; Zhang, Yuanbo; Wang, Feng; Shen, Y R; Tian, Chuanshan

2015-10-14

Sum-frequency vibrational spectroscopy was employed to probe polymer contaminants on chemical vapor deposition (CVD) graphene and to study alkane and polyethylene (PE) adsorption on graphite. In comparing the spectra from the two surfaces, it was found that the contaminants on CVD graphene must be long-chain alkane or PE-like molecules. PE adsorption from solution on the honeycomb surface results in a self-assembled ordered monolayer with the C-C skeleton plane perpendicular to the surface and an adsorption free energy of ∼42 kJ/mol for PE(H(CH2CH2)nH) with n ≈ 60. Such large adsorption energy is responsible for the easy contamination of CVD graphene by impurity in the polymer during standard transfer processes. Contamination can be minimized with the use of purified polymers free of PE-like impurities.

First principles study of dissolved oxygen water adsorption on Fe (001 surfaces

Directory of Open Access Journals (Sweden)

Dong ZHANG

2018-02-01

Full Text Available In order to study the mechanism of dissolved oxygen content on the surface corrosion behavior of Fe-based heat transfer, the first principle is used to study the adsorption of O2 monomolecular, H2O monolayer and dissolved oxygen system on Fe-based heat transfer surface. The GGA/PBE approximation is used to calculate the adsorption energy, state density and population change during the adsorption process. Calculations prove that when the dissolved oxygen is adsorbed on the Fe-based surface, the water molecule tends to adsorb at the top sites, and the oxygen molecule tends to adsorb at Griffiths. When the H2O molecule adsorbs and interacts on the Fe (001 surface, the charge distribution of the interfacial double electric layer changes to cause the Fe atoms to lose electrons, resulting in the change of the surface potential. When the O2 molecule adsorbs on the Fe (001 crystal surfaces, the electrons on the Fe (001 surface are lost and the surface potential increases. O2 molecule and the surface of the Fe atoms are prone to electron transfer, in which O atom's 2p orbit for the adsorption of O2 molecule on Fe (001 crystal surface play a major role. With the increase of the proportion of O2 molecule in the dissolved oxygen water, the absolute value of the adsorption energy increases, and the interaction of the Fe-based heat transfer surface is stronger. This study explores the influence law of different dissolved oxygen on the Fe base heat exchange surface corrosion, and the base metal corrosion mechanism for experimental study provides a theoretical reference.

Studies of red soils as capping the uranium mill tailing impoundments

International Nuclear Information System (INIS)

Wen Zhijian; Chen Zhangru; Liu Zhengyi; Chen Guoliang

2001-01-01

Capping is one of the important technical engineering measures to assure the long term stabilization and isolation of uranium mill tailings. This paper reports in situ surveys of radon emanations before and after tailings slurries were capped with local red soils at the uranium mill tailings. The data obtained by soil-gas surveys reveal that radon emanation decreased with an increase in capping thickness. The dry density of the capping materials also plays an important role in preventing radon emanation. The measurement results show that utilizing high densities of red soils as capping materials can significantly decrease the required thickness of the capping. The analytical results from borehole red soil samples show that uranium, thorium, and radium contents are consistent with the regional environmental radioactivity level. The studies of the mineralogical composition indicate that the local red soils are rich in clay minerals, e.g. kaolinite, illite and mica vermiculite mixed-layer minerals, which would play an active role in preventing radionuclide release to the surrounding environment. A conceptual model for remediation of south China's uranium mill tailing has been developed

Stability studies of plasma modification effects of polylactide and polycaprolactone surface layers

Energy Technology Data Exchange (ETDEWEB)

Moraczewski, Krzysztof, E-mail: kmm@ukw.edu.pl [Kazimierz Wielki University, Chodkiewicza 30, 85-064 Bydgoszcz (Poland); Stepczyńska, Magdalena [Kazimierz Wielki University, Chodkiewicza 30, 85-064 Bydgoszcz (Poland); Malinowski, Rafał [Institute for Engineering of Polymer Materials and Dyes, Marii Skłodowskiej-Curie 55, 87‐100 Toruń (Poland); Rytlewski, Piotr; Jagodziński, Bartłomiej; Żenkiewicz, Marian [Kazimierz Wielki University, Chodkiewicza 30, 85-064 Bydgoszcz (Poland)

2016-07-30

Highlights: • Plasma modification affects surface roughness, wettability and surface energy. • Polylactide and polycaprolactone aging causes decay of the modification effects. • Changes in the surface characteristic and wettability deterioration were observed. • The decay occurs due to migration of low molecular weight molecules to the surface. • Plasma modification effect lasts longer in the case of polycaprolactone. - Abstract: The article presents results of research on the stability of oxygen plasma modification effects of polylactide and polycaprolactone surface layers. The modified samples were aged for three, six or nine weeks. The studies were carried out using scanning electron microscopy, goniometry and Fourier transform infrared spectroscopy. Studies have shown that the plasma modification has significant impact on the geometric structure and chemical composition of the surface, wettability and surface energy of tested polymers. The modification effects are not permanent. It has been observed that over time the effects of plasma modification fade. Studies have shown that modifying effect lasts longer in the case of polycaprolactone.

Overview of surface study of fusion research in universities linkage organization, (2)

International Nuclear Information System (INIS)

Miyahara, Akira; Kamada, Kohji; Yamashina, Toshiro.

1981-02-01

Overview of surface material developments for fusion devices in university linkage organization has been described. Including subjects are surface properties investigations, surface diagnostics, coating technologies tritium related surface problems and permeation studies. Because surface material investigations are wide spread subjects, necessities of problem definitions from plasma physics side were recognized. (author)

Structural and vibrational studies of clean and chemisorbed metal surfaces

International Nuclear Information System (INIS)

Jiang, Qing-Tang.

1992-01-01

Using Medium Energy Ion Scattering, we have studied the structural and vibrational properties of a number of clean and chemisorbed metal surfaces. The work presented in this thesis is mainly of a fundamental nature. However, it is believed that an atomistic understanding of the forces that affect surface structural and vibrational properties can have a beneficial impact on a large number of areas of applied nature. We find that the surface structure of Cu(001) follows the common trend for metal surfaces, where a small oscillatory relaxation exists beginning with a slight contraction in the top layer. In addition, the surface vibrational amplitude is enhanced (as s usually the case) by ∼80%. A detailed analysis of our data shows an unexpected anisotropy of the vibrational amplitude, such that the out-of-plane vibrational amplitude is 30% smaller than the in-plane vibrational amplitude. The unexpected results may imply a large tensile stress on Cu(001). Upon adsorption of 1/4 of a monolayer of S, a p(2 x 2)-S/Cu(001) surface is created. This submonolayer amount of S atoms makes the surface bulk-like, in which the anisotropy of the surface vibrations is removed and the first interlayer contraction is lifted. By comparing our model to earlier contradictory results on this controversial system. We find excellent agreement with a recent LEED study. The presence of 0.1 monolayer of Ca atoms on the Au(113) surface induces a drastic atomic rearrangements, in which half of the top layer Au atoms are missing and a (1 x 2) symmetry results. In addition, the first interlayer spacing of Au(113) is significantly reduced. Our results are discussed in terms of the energy balance between competing surface electronic charge densities

Ab-initio study of Mg-doped InN(0001 surface

Directory of Open Access Journals (Sweden)

A. Belabbes

2013-01-01

Full Text Available We study the incorporation of Mg atoms into the InN(0001 surface. Energies and atomic geometries are described within density functional theory, while the electronic structure is investigated by an approximate quasiparticle method that yields a gap value of 0.7 eV for bulk InN. The formation of substitutional Mg is energetically favored in the surface layer. The surface electronic structure is less influenced by Mg-derived states. The Fermi level is pinned by In-derived surface states. With increasing depth of Mg beneath the surface the Fermi-level position moves toward the valence band top, suggesting formation of holes and, hence, p-doping of Mg in bulk-like layers.

Numerical study of droplet impact and rebound on superhydrophobic surface

Science.gov (United States)

Cai, Xuan; Wu, Yanchen; Woerner, Martin; Frohnapfel, Bettina

2017-11-01

Droplet impact and rebound on superhydrophobic surface is an important process in many applications; among them are developing self-cleaning or anti-icing materials and limiting liquid film formation of Diesel Exhaust Fluid (DEF) in exhaust gas pipe. In the latter field, rebound of DEF droplet from wall is desired as an effective mean for avoiding or reducing unwanted solid deposition. Our goal is to numerically study influence of surface wettability on DEF droplet impact and rebound behavior. A phase-field method is chosen, which was implemented in OpenFOAM by us and validated for wetting-related interfacial flow problems. In the present contribution we first numerically reproduce relevant experimental studies in literature, to validate the code for droplet impact and rebound problem. There we study droplet-surface contact time, maximum/instantaneous spreading factor and droplet shape evolution. Our numerical results show good agreement with experimental data. Next we investigate for DEF droplets the effects of diameter, impact velocity and surface wettability on rebound behavior and jumping height. Based on Weber number and equilibrium contact angle, two regimes are identified. We show that surface wettability is a deciding factor for achieving rebound event. This work is supported by Foundation ``Friedrich-und-Elisabeth Boysen Stiftung fuer Forschung und Innovation'' (BOY-127-TP1).

Surface studies of Os Re W alloy-coated impregnated tungsten cathodes

International Nuclear Information System (INIS)

Ares Fang, C.S.; Maloney, C.E.

1990-01-01

Impregnated tungsten cathodes half-coated with Re/W (or Os/W) alloy and Os Re W alloy at right angles were studied to compare the effects of Os Re W alloy coatings on the electron emission and emission mechanisms. Constant surface metal compositions of 32% Os--29% Re--39% W and 35% Os--26% Re--39% W were obtained from the activated surfaces initially coated with 40% Os--40% Re--20% W and 35% Os--45% Re--20% W alloys, respectively. Thermionic emission microscopy measurements showed that the Os Re W alloy-coated surface gives an average effective work function of 0.29, 0.08, and 0.03 eV lower than the uncoated, Re/W and Os/W alloy-coated surfaces. An effective work function of 1.73 eV was obtained from an activated Os Re W alloy surface. Auger studies exhibited a smaller BaO coverage and a higher barium coverage in excess of BaO stoichiometry on the Os Re W alloy-coated surface compared to the uncoated, Re/W and Os/W alloy-coated surfaces

77 FR 36447 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste

Science.gov (United States)

2012-06-19

... underflow water is an aqueous solution which seeps through the treatment zone (soils) of the North Landfarm... Trichloroethylene ND 5.00E-01 2,4,6-Trichlorophenol....... ND 2.00E+00 Vinyl chloride ND 1.56E-01 Zinc 6.05E-02 3... groundwater contamination resulting from disposal of the petitioned waste in a surface impoundment, and that a...

He-atom surface scattering apparatus for studies of crystalline surface dynamics. Progress report, May 1, 1985-April 30, 1986

International Nuclear Information System (INIS)

1986-01-01

The primary goal of this grant is the construction of a state-of-the-art He atom-crystal surface scattering apparatus which will be capable of measuring both elastic and inelastic scattering of He atoms from crystal surfaces of metals, semiconductors and insulators. First, the apparatus will be constructed and characterized, after which a program of studies on the surface dynamics of a variety of crystal surfaces will be started. 6 refs., 2 figs

The surface of 1-euro coins studied by X-ray photoelectron spectroscopy

International Nuclear Information System (INIS)

Gou, F.; Gleeson, M.A.; Villette, J.; Kleyn, S.E.F.; Kleyn, A.W.

2004-01-01

The two alloy surfaces (pill and ring) that are present on 1-euro coins have been studied by X-ray photoelectron spectroscopy (XPS). Comparison is made between coins from general circulation and coin surfaces that have been subjected to a variety of cleaning and oxidation treatments. The concentrations and possible oxidation states of the metals (nickel, copper and zinc) at the surface were derived from analysis of the 2p 3/2 core levels. The surface atomic ratios measured for the pill and the ring parts of the euro coins were compared to the official bulk ratios. This study shows a clear nickel enrichment of both pill and ring surfaces. Nickel at surface seems to be present mainly in hydroxide form although the chloride form cannot be excluded. A small concentration of zinc was present on the surface of the pill, even though it is not present in the bulk alloy. Evidence of both nickel and zinc surface enrichment is observed for the ring. No surface enrichment is observed for the atomically clean or oxidized alloy surfaces over a 60-h time scale

Experimental study on soluble chemical transfer to surface runoff from soil.

Science.gov (United States)

Tong, Juxiu; Yang, Jinzhong; Hu, Bill X; Sun, Huaiwei

2016-10-01

Prevention of chemical transfer from soil to surface runoff, under condition of irrigation and subsurface drainage, would improve surface water quality. In this paper, a series of laboratory experiments were conducted to assess the effects of various soil and hydraulic factors on chemical transfer from soil to surface runoff. The factors include maximum depth of ponding water on soil surface, initial volumetric water content of soil, depth of soil with low porosity, type or texture of soil and condition of drainage. In the experiments, two soils, sand and loam, mixed with different quantities of soluble KCl were filled in the sandboxes and prepared under different initial saturated conditions. Simulated rainfall induced surface runoff are operated in the soils, and various ponding water depths on soil surface are simulated. Flow rates and KCl concentration of surface runoff are measured during the experiments. The following conclusions are made from the study results: (1) KCl concentration in surface runoff water would decrease with the increase of the maximum depth of ponding water on soil surface; (2) KCl concentration in surface runoff water would increase with the increase of initial volumetric water content in the soil; (3) smaller depth of soil with less porosity or deeper depth of soil with larger porosity leads to less KCl transfer to surface runoff; (4) the soil with finer texture, such as loam, could keep more fertilizer in soil, which will result in more KCl concentration in surface runoff; and (5) good subsurface drainage condition will increase the infiltration and drainage rates during rainfall event and will decrease KCl concentration in surface runoff. Therefore, it is necessary to reuse drained fertile water effectively during rainfall, without polluting groundwater. These study results should be considered in agriculture management to reduce soluble chemical transfer from soil to surface runoff for reducing non-point sources pollution.

Design, development and applications of novel techniques for studying surface mechanical properties

Science.gov (United States)

Miyoshi, Kazuhisa

1989-01-01

Research is reviewed for the adhesion, friction, and micromechanical properties of materials and examples of the results presented. The ceramic and metallic materials studied include silicon carbide, aluminum oxide, and iron-base amorphous alloys. The design and operation of a torsion balance adapted for study of adhesion from the Cavendish balance are discussed first. The pull-off force (adhesion) and shear force (friction) required to break the interfacial junctions between contacting surfaces of the materials were examined at various temperatures in a vacuum. The surface chemistry of the materials was analyzed by X-ray photoelectron spectroscopy. Properties and environmental conditions of the surface regions which affect adhesion and friction-such as surface segregation, composition, crystal structure, surface chemistry, and temperature were also studied.

Reviews and syntheses: Anthropogenic perturbations to carbon fluxes in Asian river systems – concepts, emerging trends, and research challenges

Directory of Open Access Journals (Sweden)

J.-H. Park

2018-05-01

Full Text Available Human activities are drastically altering water and material flows in river systems across Asia. These anthropogenic perturbations have rarely been linked to the carbon (C fluxes of Asian rivers that may account for up to 40–50 % of the global fluxes. This review aims to provide a conceptual framework for assessing the human impacts on Asian river C fluxes, along with an update on anthropogenic alterations of riverine C fluxes. Drawing on case studies conducted in three selected rivers (the Ganges, Mekong, and Yellow River and other major Asian rivers, the review focuses on the impacts of river impoundment and pollution on CO2 outgassing from the rivers draining South, Southeast, and East Asian regions that account for the largest fraction of river discharge and C exports from Asia and Oceania. A critical examination of major conceptual models of riverine processes against observed trends suggests that to better understand altered metabolisms and C fluxes in anthropogenic land-water-scapes, or riverine landscapes modified by human activities, the traditional view of the river continuum should be complemented with concepts addressing spatial and temporal discontinuities created by human activities, such as river impoundment and pollution. Recent booms in dam construction on many large Asian rivers pose a host of environmental problems, including increased retention of sediment and associated C. A small number of studies that measured greenhouse gas (GHG emissions in dammed Asian rivers have reported contrasting impoundment effects: decreased GHG emissions from eutrophic reservoirs with enhanced primary production vs. increased emissions from the flooded vegetation and soils in the early years following dam construction or from the impounded reaches and downstream estuaries during the monsoon period. These contrasting results suggest that the rates of metabolic processes in the impounded and downstream reaches can vary greatly longitudinally

Reviews and syntheses: Anthropogenic perturbations to carbon fluxes in Asian river systems - concepts, emerging trends, and research challenges

Science.gov (United States)

Park, Ji-Hyung; Nayna, Omme K.; Begum, Most S.; Chea, Eliyan; Hartmann, Jens; Keil, Richard G.; Kumar, Sanjeev; Lu, Xixi; Ran, Lishan; Richey, Jeffrey E.; Sarma, Vedula V. S. S.; Tareq, Shafi M.; Xuan, Do Thi; Yu, Ruihong

2018-05-01

Human activities are drastically altering water and material flows in river systems across Asia. These anthropogenic perturbations have rarely been linked to the carbon (C) fluxes of Asian rivers that may account for up to 40-50 % of the global fluxes. This review aims to provide a conceptual framework for assessing the human impacts on Asian river C fluxes, along with an update on anthropogenic alterations of riverine C fluxes. Drawing on case studies conducted in three selected rivers (the Ganges, Mekong, and Yellow River) and other major Asian rivers, the review focuses on the impacts of river impoundment and pollution on CO2 outgassing from the rivers draining South, Southeast, and East Asian regions that account for the largest fraction of river discharge and C exports from Asia and Oceania. A critical examination of major conceptual models of riverine processes against observed trends suggests that to better understand altered metabolisms and C fluxes in anthropogenic land-water-scapes, or riverine landscapes modified by human activities, the traditional view of the river continuum should be complemented with concepts addressing spatial and temporal discontinuities created by human activities, such as river impoundment and pollution. Recent booms in dam construction on many large Asian rivers pose a host of environmental problems, including increased retention of sediment and associated C. A small number of studies that measured greenhouse gas (GHG) emissions in dammed Asian rivers have reported contrasting impoundment effects: decreased GHG emissions from eutrophic reservoirs with enhanced primary production vs. increased emissions from the flooded vegetation and soils in the early years following dam construction or from the impounded reaches and downstream estuaries during the monsoon period. These contrasting results suggest that the rates of metabolic processes in the impounded and downstream reaches can vary greatly longitudinally over time as a

Study on the GaAs(110) surface using emitted atom spectrometry

International Nuclear Information System (INIS)

Gayone, J.E.; Sanchez, E.A.; Grizzi, O.; Universidad Nacional de Cuyo, Mendoza

1998-01-01

The facilities implemented at Bariloche for the ion scattering spectrometry is described, and recent examples of the technique application to determine the atomic structure and the composition of metallic and semiconductor surfaces, pure and with different adsorbates. The surface analysis technique using emitted atom spectrometry is discussed. The sensitivity to the GaAs(110) surface atomic relaxation is presented, and the kinetic of hydrogen adsorption by the mentioned surface is studied

Deformation mechanism of the dam heel of Dagangshan high arch dam based on microseismic monitoring during initial impoundment%基于微震监测的大岗山高拱坝坝踵蓄水初期变形机制研究

Institute of Scientific and Technical Information of China (English)

马克; 金峰; 唐春安; 吕鹏飞; 庄端阳

2017-01-01

混凝土高拱坝坝踵是蓄水初期阶段拱坝安全的重点关注部位.通过构建国内首套高拱坝坝踵微震监测系统,实现对蓄水初期阶段大岗山拱坝坝踵区微破裂的实时监测,探究坝踵蓄水初期变形机制及其与微震活动性的关系.采用人工敲击试验确定坝踵等效P波波速为4 300 rn/s,系统定位误差小于8m.对系统获取的事件波形进行噪声滤除,并在自动定位基础上进行人工二次校核,提高定位精度,验证了微震监测技术应用于大体积混凝土工程的可行性.分析认为:蓄水初期阶段,大岗山高拱坝坝踵区微震活动性与库水位密切相关,微震事件聚集区实现从坝踵向坝趾的转移,坝踵压缩变形减小,而坝趾区变形量增加.此外,通过拱坝坝踵区微震变形演化过程,揭示了导流洞下闸蓄水前940 m高程基础廊道拱顶裂缝产生的根本诱因.研究成果可为混凝土高拱坝微震监测和真实工作性态研究提供参考.%The safety of the heel of the concrete high arch dam is highly concemed during the initial impoundment.The microseismic monitoring system was installed for the first time in China at the high arch dam heel.The real-time monitoring of the micro-cracks was achieved in the heel zone of the Dagangshan arch dam during the initial impoundment.The deformation mechanism of the arch dam heel and its relationship with the microseismic activities were investigated.The P wave velocity was determined using the manual tapping test and was 4 300 m/s with the error of system positioning less than 8 m.The event waveforms were denoised.The automatic positioning results were manually verified for better accuracy.The results proved the feasibility of applying the microseismic monitoring technology in the large-scale concrete structures.During the initial impoundment period,the microseismic activities of the high arch dam heel were closely related to the water level of reservoir.The accumulation

An ab initio study of plutonium oxides surfaces

International Nuclear Information System (INIS)

Jomard, G.; Bottin, F.; Amadon, B.

2007-01-01

By means of first-principles calculations, we have studied the atomic structure as well as the thermodynamic stability of various plutonium dioxide surfaces in function of their environment (in terms of oxygen partial pressure and temperature). All these simulations have been performed with the ABINIT code. It is well known that DFT fails to describe correctly plutonium-based materials since 5f electrons in such systems are strongly correlated. In order to go beyond DFT, we have treated PuO 2 and β-Pu 2 O 3 in a DFT+U framework. We show that the couple of parameters (U,J) that works well for pure Pu is also well designed for describing ground state (GS) properties of these two oxides. The major improvement with respect with DFT is that we are able to predict an insulating GS in agreement with experiments. The presence of a gap in the DOS (Density of States) of plutonium oxides should play a significant role in the predicted surface reactivity. However, performing DFT+U calculations on surfaces of plutonium oxide from scratch was too ambitious. That is why we decided, as a first step, to study the stability of the (100), (110) and (111) surfaces of PuO 2 in a DFT-GGA framework. For each of these orientations, we considered various terminations. These ab initio results have been introduced in a thermodynamic model which allows us to predict the relative stability of the different terminations as a function of temperature and oxygen partial pressure (p O 2 ). We conclude that at room temperature and for p O 2 ∼10 atm., the polar O 2 -(100) termination is favoured. The stabilization of such a polar stoichiometric surface is surprising and should be confirmed by DFT+U calculations before any final conclusion. (authors)

A Computational Study of Richtmyer-Meshkov Instability with Surface Tension

Science.gov (United States)

Francois, Marianne; Velechovsky, Jan; Jibben, Zach; Masser, Thomas; LANL Collaboration

2017-11-01

We have added the capability to model surface tension in our adaptive mesh refinement compressible flow solver, xRage. Our surface tension capability employs the continuum surface force to model surface tension and the height function method to compute curvatures. We have verified our model implementation for the static and oscillating droplets test cases and the linear regime of the Rayleigh-Taylor instability. With this newly added capability, we have performed a numerical study of the effects of surface tension on single-mode and multi-mode Richtmyer-Meshkov instability. This work was performed under the auspices of the National Nuclear Security Administration of the U.S. Department of Energy at Los Alamos National Laboratory under Contract No. DE-AC52 - 06NA25396.

Surface science study of selective ethylene epoxidation catalyzed by the Ag(110) surface: Structural sensitivity

International Nuclear Information System (INIS)

Campbell, C.T.

1984-01-01

The selective oxidation of ethylene to ethylene epoxide (C 2 H 4 +1/2O 2 →C 2 H 4 O) over Ag is the simplest example of kinetically controlled, selective heterogeneous catalysis. We have studied the steady-state kinetics and selectivity of this reaction for the first time on a clean, well-characterized Ag(110) surface by using a special apparatus which allows rapid (approx.20 s) transfer between a high-pressure catalytic microreactor and an ultrahigh vacuum surface analysis (AES, XPS, LEED, TDS) chamber. The effects of temperature and reactant pressures upon the rate and selectivity are virtually identical on Ag(110) and supported, high surface area Ag catalysts. The absolute specific rate (per Ag surface atom) is, however, some 100-fold higher for Ag(110) than for high surface area catalysts. This is related to the well-known structural sensitivity of this reaction. It is postulated that a small percentage of (110) planes (or [110]-like sites) are responsible for most of the catalytic activity of high surface area catalysts. The high activity of the (110) plane is attributed to its high sticking probability for dissociative oxygen adsorption, since the rate of ethylene epoxidation is shown in a related work [Ref. 1: C. T. Campbell and M. T. Paffett, Surf. Sci. (in press)] to be proportional to the coverage of atomically adsorbed oxygen at constant temperature and ethylene pressure

Surface electrical properties of stainless steel fibres: An AFM-based study

International Nuclear Information System (INIS)

Yin, Jun; D’Haese, Cécile; Nysten, Bernard

2015-01-01

Highlights: • Surface electrical conductivity of stainless steel fibre is measured and mapped by CS-AFM. • Surface potential of stainless steel fibre is measured and mapped by KPFM. • Surface electronic properties are governed by the chromium oxide passivation layer. • Electron tunnelling through the passivation layer is the dominant mechanisms for conduction. - Abstract: Atomic force microscopy (AFM) electrical modes were used to study the surface electrical properties of stainless steel fibres. The surface electrical conductivity was studied by current sensing AFM and I–V spectroscopy. Kelvin probe force microscopy was used to measure the surface contact potential. The oxide film, known as passivation layer, covering the fibre surface gives rise to the observation of an apparently semiconducting behaviour. The passivation layer generally exhibits a p-type semiconducting behaviour, which is attributed to the predominant formation of chromium oxide on the surface of the stainless steel fibres. At the nanoscale, different behaviours are observed from points to points, which may be attributed to local variations of the chemical composition and/or thickness of the passivation layer. I–V curves are well fitted with an electron tunnelling model, indicating that electron tunnelling may be the predominant mechanism for electron transport

Facial recognition and laser surface scan: a pilot study

DEFF Research Database (Denmark)

Lynnerup, Niels; Clausen, Maja-Lisa; Kristoffersen, Agnethe May

2009-01-01

Surface scanning of the face of a suspect is presented as a way to better match the facial features with those of a perpetrator from CCTV footage. We performed a simple pilot study where we obtained facial surface scans of volunteers and then in blind trials tried to match these scans with 2D...... photographs of the faces of the volunteers. Fifteen male volunteers were surface scanned using a Polhemus FastSCAN Cobra Handheld Laser Scanner. Three photographs were taken of each volunteer's face in full frontal, profile and from above at an angle of 45 degrees and also 45 degrees laterally. Via special...

Near Surface Stoichiometry in UO2: A Density Functional Theory Study

Directory of Open Access Journals (Sweden)

Jianguo Yu

2015-01-01

Full Text Available The mechanisms of oxygen stoichiometry variation in UO2 at different temperature and oxygen partial pressure are important for understanding the dynamics of microstructure in these crystals. However, very limited experimental studies have been performed to understand the atomic structure of UO2 near surface and defect effects of near surface on stoichiometry in which the system can exchange atoms with the external reservoir. In this study, the near (110 surface relaxation and stoichiometry in UO2 have been studied with density functional theory (DFT calculations. On the basis of the point-defect model (PDM, a general expression for the near surface stoichiometric variation is derived by using DFT total-energy calculations and atomistic thermodynamics, in an attempt to pin down the mechanisms of oxygen exchange between the gas environment and defected UO2. By using the derived expression, it is observed that, under poor oxygen conditions, the stoichiometry of near surface is switched from hyperstoichiometric at 300 K with a depth around 3 nm to near-stoichiometric at 1000 K and hypostoichiometric at 2000 K. Furthermore, at very poor oxygen concentrations and high temperatures, our results also suggest that the bulk of the UO2 prefers to be hypostoichiometric, although the surface is near-stoichiometric.

A time-of-flight neutron reflectometer for surface and interfacial studies

International Nuclear Information System (INIS)

Penfold, J.; Ward, R.C.; Williams, W.G.

1987-03-01

A time-of-flight neutron reflectometer constructed for surface and interfacial studies, and installed at the ISIS pulsed neutron source, is described. One of its important design features is its inclined incident beam, since this allows both liquid and solid surface phenomena to be investigated. Measurements are presented to show the performance of the instrument, and new representative results, which include studies of liquid surfaces, Langmuir-Blodgett films, and thin film multilayers, are included as illustrations of the scientific potential of the method. (author)

Surface Passivation for Single-molecule Protein Studies

Science.gov (United States)

Chandradoss, Stanley D.; Haagsma, Anna C.; Lee, Young Kwang; Hwang, Jae-Ho; Nam, Jwa-Min; Joo, Chirlmin

2014-01-01

Single-molecule fluorescence spectroscopy has proven to be instrumental in understanding a wide range of biological phenomena at the nanoscale. Important examples of what this technique can yield to biological sciences are the mechanistic insights on protein-protein and protein-nucleic acid interactions. When interactions of proteins are probed at the single-molecule level, the proteins or their substrates are often immobilized on a glass surface, which allows for a long-term observation. This immobilization scheme may introduce unwanted surface artifacts. Therefore, it is essential to passivate the glass surface to make it inert. Surface coating using polyethylene glycol (PEG) stands out for its high performance in preventing proteins from non-specifically interacting with a glass surface. However, the polymer coating procedure is difficult, due to the complication arising from a series of surface treatments and the stringent requirement that a surface needs to be free of any fluorescent molecules at the end of the procedure. Here, we provide a robust protocol with step-by-step instructions. It covers surface cleaning including piranha etching, surface functionalization with amine groups, and finally PEG coating. To obtain a high density of a PEG layer, we introduce a new strategy of treating the surface with PEG molecules over two rounds, which remarkably improves the quality of passivation. We provide representative results as well as practical advice for each critical step so that anyone can achieve the high quality surface passivation. PMID:24797261

Aspects of studies on carbon cycle at ground surface

International Nuclear Information System (INIS)

Yamazawa, Hiromi; Kawai, Shintaro; Moriizumi, Jun; Iida, Takao

2008-01-01

Radiocarbon released from nuclear facilities into the atmosphere is readily involved in a ground surface carbon cycle, which has very large spatial and temporal variability. Most of the recent studies on the carbon cycle at the ground surface are concerned with global warming, to which the ground surface plays a crucial role as a sink and/or source of atmospheric carbon dioxide. In these studies, carbon isotopes are used as tracers to quantitatively evaluate behavior of carbon. From a view point of environmental safety of nuclear facilities, radiocarbon released from a facility should be traced in a specific spatial and temporal situation because carbon cycle is driven by biological activities which are spatially and temporally heterogeneous. With this background, this paper discusses aspects of carbon cycle studies by exemplifying an experimental study on carbon cycle in a forest and a numerical study on soil organic carbon formation. The first example is a typical global warming-related observational study in which radiocarbon is used as a tracer to illustrate how carbon behaves in diurnal to seasonal time scales. The second example is on behavior of bomb carbon incorporated in soil organic matter in a long-term period of decades. The discussion will cover conceptual modelling of carbon cycle from different aspects and importance of specifying time scales of interest. (author)

National Dam Inspection Program. Ingham Creek (Aquetong Lake) Dam (NDI ID PA 00224, PA DER 9-49) Delaware River Basin, Ingham Creek, Pennsylvania. Phase I Inspection Report,

Science.gov (United States)

1981-04-01

Delaware River Basing Ingham Justif icaticn--- L Creek, Pennsylvania. Phase I Inspection Do DEL-AWARE RIVER BASIN Availabilit T Co~es Avail and/or D...about 1.5H:IV and an unknown upstream slope below the water surface. The dam impounds a reservoir with a normal pool surface area of 12.4 acres and a...deep. It was once used to direct water to a mill downstream of the dam and is now in poor condition. The spillway Design Flood (SDF) chosen for this

Experimental and numerical studies on free surface flow of windowless target

International Nuclear Information System (INIS)

Su, G.Y.; Gu, H.Y.; Cheng, X.

2012-01-01

Highlights: ► Experimental and CFD studies on free surface flow have been performed in a scaled windowless target. ► Flow structure inside spallation area can be divided into three typical zones. ► Under large Reynolds number, large scale vortex can be observed. ► CFD studies have been conducted by using both LES and RANS (k-ω SST) turbulence models. ► LES model provides better numerical prediction on free surface behavior and flow transient. - Abstract: The formation and control method of the coolant free surface is one of the key technologies for the design of windowless targets in the accelerator driven system (ADS). In the recent study, experimental and numerical investigations on the free surface flow have been performed in a scaled windowless target by using water as the model fluid. The planar laser induced fluorescence technique has been applied to visualize the free surface flow pattern inside the spallation area. Experiments have been carried out with the Reynolds number in the range of 30,000–50,000. The structure and features of flow vortex have been investigated. The experimental results show that the free surface is vulnerable to the vortex movement. In addition, CFD simulations have been performed under the experimental conditions, using LES and RANS (k-ω SST) turbulence models, respectively. The numerical results of LES model agree qualitatively well with the experimental data related to both flow pattern and free surface behavior.

A first-principles study of oxygen adsorption on Ir(111) surface

Energy Technology Data Exchange (ETDEWEB)

Gao, Hengjiao, E-mail: gaohengjiao@163.com; Xiong, Yuqing, E-mail: xiongyq@hotmail.com; Liu, Xiaoli, E-mail: shantianzi@126.com; Zhao, Dongcai, E-mail: zhaodongc@163.com; Feng, Yudong, E-mail: yudong_feng@sina.com; Wang, Lanxi, E-mail: wanglanxi@live.com; Wang, Jinxiao, E-mail: coldwind716@gmail.com

2016-12-15

Highlights: • Adsorption of oxygen on Ir(111) surface was studied by density functional theory. • The most stable adsorption site was determined by adsorption energy calculation. • Adsorption of oxygen at bridge and top site on Ir surface was the most stable ones. • Interaction of O 2p and Ir 5d orbits is relatively strong and formed hybridization. - Abstract: In order to understand deposition mechanism of iridium thin film by atomic layer deposition, the adsorption of oxygen on Ir(111) surface was studied by use of density functional theory and a periodical slab model. By calculating the adsorption energy and structure of oxygen at four adsorption sites (top, bridge, fcc-hollow and hcp-hollow) on Ir(111) surface, the most stable adsorption site was determined. On this basis, the banding mechanism of O and Ir atoms was studied by density of states of oxygen and iridium atoms. Oxygen adsorbed at hcp(parallel) site on Ir(111) surface was the most stable one according to the adsorption energy calculation results. Orbital charge analysis indicate that charge transferred from 5p and 5d orbit to 2p orbit of adsorbed O atoms, and 6s orbit of iridium atoms. Meanwhile, density of state study indicated that adsorption of oxygen on Ir(111) surface is mainly due to the interaction between 2p orbit of O atoms and 5d orbit of iridium atoms.

Photoelectron studies of machined brass surfaces

Science.gov (United States)

Potts, A. W.; Merrison, J. P.; Tournas, A. D.; Yacoot, A.

UV photoelectron spectroscopy has been used to determine the surface composition of machined brass. The results show a considerable change between the photoelectron surface composition and the bulk composition of the same sample determined by energy-dispersive X-ray fluorescence. On the surface the lead composition is increased by ˜900 G. This is consistent with the important part that lead is believed to play in improving the machinability of this alloy.

Temporal trend analysis of RCRA groundwater monitoring data

International Nuclear Information System (INIS)

Need, E.A.

1994-01-01

Statistical analysis of RCRA groundwater monitoring data at a uranium hexafluoride processing facility showed a statistically significant increase in the concentration of gross beta activity in monitor wells downgradient of surface impounds storing calcium fluoride sludge and high pH water. Because evidence of leakage had not been detected in lysimeters installed beneath the impounds, the operator sought an evaluation of other potential causes of the result, including natural variability. This study determined that all five data sets showed either long-term excursionary (spike-like), or seasonal forms of temporal variation. Gross beta had an upward long-term trend with multiple excursions that almost appeared to be seasonal. Gross alpha had an upward long-term trend with multiple excursions that were clearly not seasonal. Specific conductance had both upward and downward long-term trends but no other variations. pH had a downward long-term trend with multiple excursions that were clearly not seasonal. Fluoride had a downward long-term trend without excursions but with clear seasonal variations. The gross beta result that appeared to be a significant change was a spike event on the upward long-term trend

Theoretical modelling of semiconductor surfaces microscopic studies of electrons and photons

CERN Document Server

Srivastava, G P

1999-01-01

The state-of-the-art theoretical studies of ground state properties, electronic states and atomic vibrations for bulk semiconductors and their surfaces by the application of the pseudopotential method are discussed. Studies of bulk and surface phonon modes have been extended by the application of the phenomenological bond charge model. The coverage of the material, especially of the rapidly growing and technologically important topics of surface reconstruction and chemisorption, is up-to-date and beyond what is currently available in book form. Although theoretical in nature, the book provides

Surface magnetism studied by polarized light emission after He+ scattering

NARCIS (Netherlands)

Manske, J; Dirska, M; Lubinski, G; Schleberger, M; Narmann, A; Hoekstra, R

Surface magnetism is studied by means of an ion beam of low energy (2-15 keV) scattered off the surface under grazing incidence conditions. During the scattering, a small fraction of the ions is neutralized into excited states which decay subsequently by light emission. The circular polarization of

Studies of cell biomechanics with surface micro-/nano-technology

International Nuclear Information System (INIS)

Wang Dong; Zhang Wei; Jiang Xingyu

2011-01-01

We report the recent progress in our studies of cell biology using micro-/nano-technology. Cells have a size of several to tens of microns, which makes them easily manipulated by micro-/nano-technology. The shape of the cell influences the alignment of the actin cytoskeleton, which bears the main forces of the cell, maintains the shape,and mediates a series of biochemical reactions. We invented a stretching device and studied the real-time actin filament dynamics under stretch. We found that one stretch cycle shortened the actin filaments and promoted their reassemble process. Cell migration is a complex mechanical process. We found that cell geometry determines the cell polarity and migration direction. We fabricated three-dimensional surfaces to mimic the topography in vivo, and further built a cell culture model by integrating the three-dimensional surface, microfluidics, cell patterning,and coculturing of multiple cell types. We also investigated the neuronal guidance by surface patterning. (authors)

Functionality of novel black silicon based nanostructured surfaces studied by TOF SIMS

DEFF Research Database (Denmark)

Talian, Ivan; Aranyosiova, M.; Orinak, A.

2010-01-01

A functionality of the novel black silicon based nanostructured surfaces (BS 2) with different metal surface modifications was tested by time-of-flight secondary ion mass spectrometry (TOF SIMS). Mainly two surface functions were studied: analytical signal enhancement and analyte pre-ionization e......A functionality of the novel black silicon based nanostructured surfaces (BS 2) with different metal surface modifications was tested by time-of-flight secondary ion mass spectrometry (TOF SIMS). Mainly two surface functions were studied: analytical signal enhancement and analyte pre......-ionization effect in SIMS due to nanostructure type and the assistance of the noble metal surface coating (Ag or Au) for secondary ion formation. As a testing analyte a Rhodamine 6G was applied. Bi+ has been used as SIMS primary ions. It was found out that SIMS signal enhancement of the analyte significantly...... depends on Ag layer thickness and measured ion mode (negative, positive). The best SIMS signal enhancement was obtained at BS2 surface coated with 400 nm of Ag layer. SIMS fragmentation schemes were developed for a model analyte deposited onto a silver and gold surface. Significant differences in pre...

Studies on deposition of radon daughters on glass surface

International Nuclear Information System (INIS)

Loerinc, M.; Feher, I.; Palfalvi, J.

1998-01-01

In a certain village in Northern Hungary, in some houses the radon concentration was found to be in the order of kBq.m -3 . In an attempt to decide whether an earthquake or the near-by mining activity is to blame, past radon concentration was studied making use of radon daughters embedded in the surface layer of glass sheets. In the investigation several conclusions were reached: drastic changes in Rn concentration could be excluded, ie., the high Rn concentration existed over the last 50 years; the continuing deposition of dirt on the glass surface and the occasional cleaning had no significant effect; the effect of corrosion processes at the glass surface should be further investigated. (A.K.)

Surface structure analysis by means of Rutherford scattering: methods to study surface relaxation

International Nuclear Information System (INIS)

Turkenburg, W.C.; Soszka, W.; Saris, F.W.; Kersten, H.H.; Colenbrander, B.G.

1976-01-01

The use of Rutherford backscattering for structural analysis of single crystal surfaces is reviewed, and a new method is introduced. With this method, which makes use of the channeling and blocking phenomenon of light ions of medium energy, surface atoms can be located with a precision of 0.02 A. This is demonstrated in a measurement of surface relaxation for the Cu(110) surface. (Auth.)

Study Paths, Riemann Surfaces, and Strebel Differentials

Science.gov (United States)

Buser, Peter; Semmler, Klaus-Dieter

2017-01-01

These pages aim to explain and interpret why the late Mika Seppälä, a conformal geometer, proposed to model student study behaviour using concepts from conformal geometry, such as Riemann surfaces and Strebel differentials. Over many years Mika Seppälä taught online calculus courses to students at Florida State University in the United States, as…

Inherent wettability of different rock surfaces at nanoscale: a theoretical study

Science.gov (United States)

Chang, Xiao; Xue, Qingzhong; Li, Xiaofang; Zhang, Jianqiang; Zhu, Lei; He, Daliang; Zheng, Haixia; Lu, Shuangfang; Liu, Zilong

2018-03-01

Investigating the inherent wettability of rock surfaces at nanoscale is of great importance in ore floatation and oil recovery field. Using molecular dynamics simulations, we systematically study the wetting behavior of water on different rock surfaces (silica, calcite, gypsum, halite and graphite) at nanoscale. It is demonstrated that the inherent rock wettability follows the order of gypsum > calcite > halite > silica > graphite. Remarkably, we also manifest that the polarity of oil molecules can affect the water contact angles on silica surface. For example, the water contact angles on silica surface in hexane, dodecane, thiophene and toluene are 58 ± 2°, 63 ± 3°, 90 ± 1°, 118 ± 1°, respectively. Furthermore, we investigate the wetting behavior of water on heterogeneous rock surfaces and find that water molecules can move from hydrophobic surface to hydrophilic surface.

Upland and wetland vegetation establishment on coal slurry in northern Missouri

International Nuclear Information System (INIS)

Skeel, V.A.; Nawrot, J.R.

1998-01-01

Since the Cooperative Wildlife Research Laboratory's (CWRL) Mined Land Reclamation Program's first establishment of a wetland on slurry in 1976, industry, state, and federal agency interest in reclamation alternatives for inactive slurry has increased. CWRL has been involved in pre-reclamation site characterization and monitoring for inactive slurry impoundments throughout Illinois, Indiana, Kansas, Kentucky, Missouri, and Washington. Geochemical site characterization of three slurry impoundments at the AECI Bee Veer Mine located near Macon, Missouri began in April 1990. A substrate sampling grid was established for all slurry impoundments with a centerline orientated parallel to the discharge to decant flow pattern. Surface (0--6 in.) and subsurface (30--36 in.) slurry samples were collected annually and analyzed for acid-base balance, immediate acidity macro- and micro-nutrients, potential phytotoxic metallic ions and salts, and texture. Water table elevations and water quality were monitored quarterly from shallow (≤12 ft.) piezometers. General reclamation plans included annual (3 years) incremental limestone amendments (35--50 tons/acre) and direct vegetation establishment. Cool and warm season grasses dominate vegetation cover in upland habitats (slurry cell RDA1) while wetland habitats (palustrine emergent seasonally-permanently inundated) have been established in slurry cells (RDA2 and RDA3). Isolated hot spots continue to be amended with limestone and supplemental vegetation establishment is scheduled

Evolution of Acid Mine Drainage Formation in Sulphidic Mine Tailings

Directory of Open Access Journals (Sweden)

Bernhard Dold

2014-07-01

Full Text Available Sulphidic mine tailings are among the largest mining wastes on Earth and are prone to produce acid mine drainage (AMD. The formation of AMD is a sequence of complex biogeochemical and mineral dissolution processes. It can be classified in three main steps occurring from the operational phase of a tailings impoundment until the final appearance of AMD after operations ceased: (1 During the operational phase of a tailings impoundment the pH-Eh regime is normally alkaline to neutral and reducing (water-saturated. Associated environmental problems include the presence of high sulphate concentrations due to dissolution of gypsum-anhydrite, and/or effluents enriched in elements such as Mo and As, which desorbed from primary ferric hydroxides during the alkaline flotation process. (2 Once mining-related operations of the tailings impoundment has ceased, sulphide oxidation starts, resulting in the formation of an acidic oxidation zone and a ferrous iron-rich plume below the oxidation front, that re-oxidises once it surfaces, producing the first visible sign of AMD, i.e., the precipitation of ferrihydrite and concomitant acidification. (3 Consumption of the (reactive neutralization potential of the gangue minerals and subsequent outflow of acidic, heavy metal-rich leachates from the tailings is the final step in the evolution of an AMD system. The formation of multi-colour efflorescent salts can be a visible sign of this stage.

study and analysis of asa river hypothetical dam break using hec-ras

African Journals Online (AJOL)

Impounded reservoirs provide beneficial functions such as flood control, recreation, hydropower and water supply but they also carry potential risks. Spontaneous dam break phenomenon can occur and the resultant flooding may cause substantial loss of life and property damage downstream of the dam. A hypothetical dam ...

Ammonia synthesis over a Ru(0001) surface studied by density functional calculations

DEFF Research Database (Denmark)

Logadottir, Ashildur; Nørskov, Jens Kehlet

2003-01-01

In this paper we present DFT studies of all the elementary steps in the synthesis of ammonia from gaseous hydrogen and nitrogen over a ruthenium crystal. The stability and configurations of intermediates in the ammonia synthesis over a Ru(0001) surface have been investigated, both over a flat...... surface and over a stepped surface. The calculations show that the step sites on the surface are much more reactive than the terrace sites. The DFT results are then used to study the mechanism of promotion by alkalies over the Ru(0001) and to determine the rate-determining step in the synthesis of ammonia...

Spectroscopic studies of organometallic compounds on single crystal metal surfaces: Surface acetylides of silver (110)

Science.gov (United States)

Madix, Robert J.

The nature of compounds formed by the reaction of organic molecules with metal surfaces can be studied with a battery of analytical methods based on both physicals and chemical understanding. In this paper the application of UPS, XPS, LEED and EELS as well as temperature programmed reaction spectroscopy (TPRS) and chemical titration methods to the characterization of surface complexes is discussed. Particular emphasis is given to the reaction of acetylene with a single crystal surface of silver, Ag(110). Previous work has shown that this surface, when clean, is unreactive to hydrocarbons, alcohols and carboxylic acids under ultra high vacuum conditions. Preadsorption of oxygen, however, renders the surface reactive, and a wide variety of organometallic surface compounds can be formed. As expected then, no stable adsorption state and no reaction was observed with clean Ag(110) following room temperature exposure to acetylene. Following exposure at 150 K, however, a weekly bound chemisorption state was observed to desorb at 195 K, indicating a binding energy to the surface of approximately 12 kcal/gmole. Reaction with preadsorbed oxygen gave water formulation upon dosing and produced surface intermediates which yeilded two acetylene desorption states at 195 and 175 K. Heating above 300 K to completely desorb the higher temperature state produced new, well-defined LEED Features due to residual surface carbon which disappeared when the surface was heated above 550 K. Clearly, there were distinc changes in the nature of the absorbed layer at 195, 300 and 550 K. These changes were reflected in XPS. For the weakly chemisorbed acetylene a large C(ls) peak at 285.6 eV with a small, broad, indistinc shoulder at higher binding energy (288.2) was observed. The spectrum of the species following acetylene desorption at 275 K, however, showed the formulation of a large C(ls) peak at 283.6 eV in addition to peaks characteristics of the weakly chemisorbed state. This result

Numerical study of aerodynamic effects on road vehicles lifting surfaces

Science.gov (United States)

Cernat, Mihail Victor; Cernat Bobonea, Andreea

2017-01-01

The aerodynamic performance analysis of road vehicles depends on the study of engine intake and cooling flow, internal ventilation, tire cooling, and overall external flow as the motion of air around a moving vehicle affects all of its components in one form or another. Due to the complex geometry of these, the aerodynamic interaction between the various body components is significant, resulting in vortex flow and lifting surface shapes. The present study, however focuses on the effects of external aerodynamics only, and in particular on the flow over the lifting surfaces of a common compact car, designed especially for this study.

Quantitative study of Xanthosoma violaceum leaf surfaces using RIMAPS and variogram techniques.

Science.gov (United States)

Favret, Eduardo A; Fuentes, Néstor O; Molina, Ana M

2006-08-01

Two new imaging techniques (rotated image with maximum averaged power spectrum (RIMAPS) and variogram) are presented for the study and description of leaf surfaces. Xanthosoma violaceum was analyzed to illustrate the characteristics of both techniques. Both techniques produce a quantitative description of leaf surface topography. RIMAPS combines digitized images rotation with Fourier transform, and it is used to detect patterns orientation and characteristics of surface topography. Variogram relates the mathematical variance of a surface with the area of the sample window observed. It gives the typical scale lengths of the surface patterns. RIMAPS detects the morphological variations of the surface topography pattern between fresh and dried (herbarium) samples of the leaf. The variogram method finds the characteristic dimensions of the leaf microstructure, i.e., cell length, papillae diameter, etc., showing that there are not significant differences between dry and fresh samples. The results obtained show the robustness of RIMAPS and variogram analyses to detect, distinguish, and characterize leaf surfaces, as well as give scale lengths. Both techniques are tools for the biologist to study variations of the leaf surface when different patterns are present. The use of RIMAPS and variogram opens a wide spectrum of possibilities by providing a systematic, quantitative description of the leaf surface topography.

Long-Term Downstream Effects of a Dam on a Lowland River Flow Regime: Case Study of the Upper Narew

Directory of Open Access Journals (Sweden)

Paweł Marcinkowski

2017-10-01

Full Text Available Most European riverine ecosystems suffer from the negative influence of impoundments on flow regime. Downstream effects of dams lead to a number of environmental and socioeconomic risks and, therefore, should be thoroughly examined in specific contexts. Our study aims to quantify the downstream effects of the Siemianówka Reservoir (Upper Narew, Poland, using statistical analysis of key elements of the river’s flow regime, such as the flow duration and recurrence of floods and droughts. In a comparative study on control catchments not influenced by impoundments (the Supraśl and Narewka Rivers, we revealed the following downstream effects of the analyzed dam: significant shortening of spring floods, reduction of the duration and depth of summer droughts, decrease of the maximum discharge, and homogenization of the discharge hydrographs. Although we determined a significant decrease in the duration of summer floods in the “before” and “after” dam function periods, we showed that this issue is regional, climate-related, and replicated in control catchments, rather than an evident downstream effect of the dam. We conclude that significant hydrological downstream effects of the Siemianówka dam–reservoir system could have been the main driver inducing the deterioration of the anastomosing stretch of the Narew River downstream of the dam.

Study of ultra-clean surfaces for accelerator structures

International Nuclear Information System (INIS)

Saito, K.; Noguchi, S.; Kako, E.

1994-01-01

For a TeV energy physics R and D on electron/positron linear colliders has been conducted hard at many laboratories from technologies of both normal conducting and superconducting. The high field gradient issue is a key to realize such a machine. Field emission limits seriously field gradient of rf cavities. Its cure is to eliminate particle contamination on cavity surfaces. It is a common issue in both normal conducting and superconducting cavities. We have started to study ultra-clean surfaces of niobium and copper applying semiconductor technologies. In this paper several results by various rinsing methods are presented and its relation with cavity performance is discussed. (author)

Surface studies of microcrystalline chitosan/poly(vinyl alcohol) mixtures

Energy Technology Data Exchange (ETDEWEB)

Lewandowska, Katarzyna, E-mail: reol@chem.uni.torun.pl [Nicolaus Copernicus University, Faculty of Chemistry, Chair of Chemistry and Photochemistry of Polymers, 7 Gagarin Street, 87-100 Torun (Poland)

2012-12-15

Highlights: Black-Right-Pointing-Pointer The surface properties were investigated by AFM, SEM and FTIR. Black-Right-Pointing-Pointer The AFM images showed the lamellar structure of PVA in the blend. Black-Right-Pointing-Pointer SEM microscopy confirmed the existence of microphase separation of components. Black-Right-Pointing-Pointer FTIR analysis showed the existence of a weak interaction. - Abstract: In the present study, the surface properties of microcrystalline chitosan (MCCh), poly(vinyl alcohol) (PVA) and MCCh/PVA blends (made from acetic acid solutions with the MCCh concentration ranging from 20% to 80%) have been studied by the tapping-mode atomic force microscopy (AFM), scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. The changes of topography images are considered by determining the root mean square (RMS, R{sub q}) deviation in the image data. For PVA samples, the transition between adjacent lamellae occurs through holes, islands, and bicontinuous structures. The AFM images showed also the lamellar structure of PVA in the blend. The crystalline topography of MCCh/PVA film surface suggests the presence of PVA on the top surface. The FTIR spectra of film blends, in the amide I and II region of MCCh and the hydroxyl stretching bands of PVA have been analyzed. FTIR analysis showed the existence of a weak interaction of the hydroxyl or amino groups of microcrystalline chitosan with hydroxyl groups of PVA.

Surface studies of microcrystalline chitosan/poly(vinyl alcohol) mixtures

International Nuclear Information System (INIS)

Lewandowska, Katarzyna

2012-01-01

Highlights: ► The surface properties were investigated by AFM, SEM and FTIR. ► The AFM images showed the lamellar structure of PVA in the blend. ► SEM microscopy confirmed the existence of microphase separation of components. ► FTIR analysis showed the existence of a weak interaction. - Abstract: In the present study, the surface properties of microcrystalline chitosan (MCCh), poly(vinyl alcohol) (PVA) and MCCh/PVA blends (made from acetic acid solutions with the MCCh concentration ranging from 20% to 80%) have been studied by the tapping-mode atomic force microscopy (AFM), scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. The changes of topography images are considered by determining the root mean square (RMS, R q ) deviation in the image data. For PVA samples, the transition between adjacent lamellae occurs through holes, islands, and bicontinuous structures. The AFM images showed also the lamellar structure of PVA in the blend. The crystalline topography of MCCh/PVA film surface suggests the presence of PVA on the top surface. The FTIR spectra of film blends, in the amide I and II region of MCCh and the hydroxyl stretching bands of PVA have been analyzed. FTIR analysis showed the existence of a weak interaction of the hydroxyl or amino groups of microcrystalline chitosan with hydroxyl groups of PVA.

Surface science studies of ethene containing model interstellar ices

Science.gov (United States)

Puletti, F.; Whelan, M.; Brown, W. A.

2011-05-01

The formation of saturated hydrocarbons in the interstellar medium (ISM) is difficult to explain only by taking into account gas phase reactions. This is mostly due to the fact that carbonium ions only react with H_2 to make unsaturated hydrocarbons, and hence no viable route to saturated hydrocarbons has been postulated to date. It is therefore likely that saturation processes occur via surface reactions that take place on interstellar dust grains. One of the species of interest in this family of reactions is C_2H_4 (ethene) which is an intermediate in several molecular formation routes (e.g. C_2H_2 → C_2H_6). To help to understand some of the surface processes involving ethene, a study of ethene deposited on a dust grain analogue surface (highly oriented pyrolytic graphite) held under ultra-high vacuum at 20 K has been performed. The adsorption and desorption of ethene has been studied both in water-free and water-dominated model interstellar ices. A combination of temperature programmed desorption (TPD) and reflection absorption infrared spectroscopy (RAIRS) have been used to identify the adsorbed and trapped species and to determine the kinetics of the desorption processes. In all cases, ethene is found to physisorb on the carbonaceous surface. As expected water has a very strong influence on the desorption of ethene, as previously observed for other model interstellar ice systems.

FDTD/TDSE study of surface-enhanced infrared absorption by metal nanoparticles.

Energy Technology Data Exchange (ETDEWEB)

Chang, S.-H.; Schatz, G. C.; Gray, S. K.; Chemistry; Northwestern Univ.; National Cheng-Kung Univ.

2006-01-01

We study surface-enhanced infrared absorption, including multiphoton processes, due to the excitation of surface plasmons on metal nanoparticles. The time-dependent Schroedinger equation and finite-difference time-domain method are self-consistently coupled to treat the problem.

Studies of the surface of titanium dioxide. IV. The hydrogen-deuterium equilibration reaction

International Nuclear Information System (INIS)

Iwaki, T.; Katsuta, K.; Miura, M.

1981-01-01

The interaction of hydrogen with the surface of titanium dioxide has been studied in connection with the hydrogen-reduction mechanism of titanium dioxide, by means of such measurements as weight decrease, magnetic susceptibility, hydrogen uptake, and electrical conductance. It was postulated in the previous study that the rate-determining step of the hydrogen-reduction reaction may be the formation of surface hydroxyl groups, followed by the rapid removal of water molecules from the surface. In this study, the interactions between hydrogen and the surface of titanium dioxide were investigated by measuring the hydrogen-deuterium equilibration reaction, H 2 + D 2 = 2HD, at temperatures above 200 0 C on both surfaces before and after hydrogen reduction to compare the differences in the reactivities

Study on tribological properties of multi-layer surface texture on Babbitt alloys surface

Science.gov (United States)

Zhang, Dongya; Zhao, Feifei; Li, Yan; Li, Pengyang; Zeng, Qunfeng; Dong, Guangneng

2016-12-01

To improve tribological properties of Babbitt alloys, multi-layer surface texture consisted of the main grooves and secondary micro-dimples are fabricated on the Babbitt substrate through laser pulse ablation. The tribological behaviors of multi-layer surface texture are investigated using a rotating type pin-on-disc tribo-meter under variation sliding speeds, and the film pressure distributions on the textured surfaces are simulated using computational fluid dynamics (CFD) method for elucidating the possible mechanisms. The results suggest that: (i) the multi-layer surface texture can reduce friction coefficient of Babbitt alloy, which has lowest friction coefficient of 0.03, in case of the groove parameter of 300 μm width and 15% of area density; (ii) the improvement effect may be more sensitive to the groove area density and the siding speed, and the textured surface with lower area density has lower friction coefficient under high sliding speed. Based on the reasons of (i) the secondary micro-dimples on Babbitt alloy possesses a hydrophobicity surface and (ii) the CFD analysis indicates that main grooves enhancing hydrodynamic effect, thus the multi-layer surface texture is regarded as dramatically improve the lubricating properties of the Babbitt alloy.

The Multimedia Environmental Pollutant Assessment System (MEPAS)reg-sign: Riverine pathway formulations

International Nuclear Information System (INIS)

Whelan, G.; McDonald, J.P.

1996-11-01

This report describes the mathematical formulations used for contaminant fate and transport in the riverine pathway of the Multimedia Environmental Pollutant Assessment System (MEPAS). Of the many types of surface-water bodies (e.g., nontidal rivers, estuaries, lakes, open coasts, reservoirs, impoundments, etc.) in which contaminant fate and transport could be simulated, only a nontidal river model is currently incorporated into MEPAS. Nontidal rivers refer to freshwater bodies with unidirectional flow in definable channels. Because the MEPAS methodology is compositely coupled, other surface-water models can be added when deemed necessary

Experimental studies of photon-surface interaction dynamics in the alkali halides

International Nuclear Information System (INIS)

Haglund, R.F. Jr.; Tolk, N.H.

1986-01-01

We describe recent measurements which have provided, in unprecedented detail, insights into the electronic mechanisms through which energy carried into a material by photon irradiation is absorbed, localized and rechanneled to produce desorption, surface modification, erosion and damage. The specific object of these studies has been desorption induced by electronic transition in alkali halide crystals, with particular emphasis on the dynamics of changes in the surface and near-surface regions. In our experiments, the irradiating ultraviolet photons are provided by a synchrotron storage ring, and the dynamical information about desorption products is obtained from optical measurements of the quantum states, yields and velocity distributions of neutral ground-state and excited-state atoms ejected from the surface of the irradiating material. These studies have shown that the dominant exit channels in photon-induced particle emission are those producing ground-state and excited-state neutral atoms. Using dynamical information about these desorbing neutral species, obtained, for example, by laser-induced fluorescence and laser Doppler spectroscopy, we are generating an increasingly comprehensive picture of the dynamics of electronic energy flow into and out of pure crystalline surfaces in these prototypical dielectrics. We are also beginning to be able to relate desorption dynamics to specific materials properties, and to discriminate between pure surface and near-surface effects in these materials. Applications of these techniques to the problem of photon-induced surface damage and to analysis of surface dynamics in dielectric materials are discussed, and the relationships between these nearly ideal model materials and the non-crystalline, covalently bonded materials more typical of real optical elements are pointed out. 19 refs., 13 figs

Surface phenomena revealed by in situ imaging: studies from adhesion, wear and cutting

Science.gov (United States)

Viswanathan, Koushik; Mahato, Anirban; Yeung, Ho; Chandrasekar, Srinivasan

2017-03-01

Surface deformation and flow phenomena are ubiquitous in mechanical processes. In this work we present an in situ imaging framework for studying a range of surface mechanical phenomena at high spatial resolution and across a range of time scales. The in situ framework is capable of resolving deformation and flow fields quantitatively in terms of surface displacements, velocities, strains and strain rates. Three case studies are presented demonstrating the power of this framework for studying surface deformation. In the first, the origin of stick-slip motion in adhesive polymer interfaces is investigated, revealing a intimate link between stick-slip and surface wave propagation. Second, the role of flow in mediating formation of surface defects and wear particles in metals is analyzed using a prototypical sliding process. It is shown that conventional post-mortem observation and inference can lead to erroneous conclusions with regard to formation of surface cracks and wear particles. The in situ framework is shown to unambiguously capture delamination wear in sliding. Third, material flow and surface deformation in a typical cutting process is analyzed. It is shown that a long-standing problem in the cutting of annealed metals is resolved by the imaging, with other benefits such as estimation of energy dissipation and power from the flow fields. In closure, guidelines are provided for profitably exploiting in situ observations to study large-strain deformation, flow and friction phenomena at surfaces that display a variety of time-scales.

Surface Pourbaix diagrams and oxygen reduction activity of Pt, Ag and Ni(111) surfaces studied by DFT

DEFF Research Database (Denmark)

Hansen, Heine Anton; Rossmeisl, Jan; Nørskov, Jens Kehlet

2008-01-01

The electrochemical most stable surface structures is investigated as function of pH and potential for Pt, Ag and Ni based on DFT calculations and constructed surface Pourbaix diagrams. It is also explained why metals such as Ag and Ni may be used successfully in alkaline fuel cells but not in ac......The electrochemical most stable surface structures is investigated as function of pH and potential for Pt, Ag and Ni based on DFT calculations and constructed surface Pourbaix diagrams. It is also explained why metals such as Ag and Ni may be used successfully in alkaline fuel cells...... but not in acidic PEM fuel cells. Based on density functional theory calculations we investigate the electrochemically most stable surface structures as a function of pH and electrostatic potential for Pt(111), Ag(111) and Ni(111), and we construct surface Pourbaix diagrams. We study the oxygen reduction reaction......, on the other hand, is constant vs. the standard hydrogen electrode (SHE). For Ag, this means that where the potential for dissolution and ORR are about the same at pH = 0, Ag becomes more stable relative to RHE as pH is increased. Hence the pH dependent stability offers an explanation for the possible use...

Surface Propensity of Atmospherically Relevant Amino Acids Studied by XPS.

Science.gov (United States)

Mocellin, Alexandra; Gomes, Anderson Herbert de Abreu; Araújo, Oscar Cardoso; de Brito, Arnaldo Naves; Björneholm, Olle

2017-04-27

Amino acids constitute an important fraction of the water-soluble organic nitrogen (WSON) compounds in aerosols and are involved in many processes in the atmosphere. In this work, we applied X-ray photoelectron spectroscopy (XPS) to study aqueous solutions of four amino acids, glycine, alanine, valine, and methionine, in their zwitterionic forms. We found that amino acids with hydrophilic side chains and smaller size, GLY and ALA, tend to stay in the bulk of the liquid, while the hydrophobic and bigger amino acids, VAL and MET, are found to concentrate more on the surface. We found experimental evidence that the amino acids have preferential orientation relative to the surface, with the hydrophobic side chain being closer to the surface than the hydrophilic carboxylate group. The observed amino acid surface propensity has implications in atmospheric science as the surface interactions play a central role in cloud droplet formation, and they should be considered in climate models.

Study on the Light Scattering from Random Rough Surfaces by Kirrhoff Approximation

Directory of Open Access Journals (Sweden)

Keding Yan

2014-07-01

Full Text Available In order to study the space distribution characteristics of light scattering from random rough surfaces, the linear filtering method is used to generate a series of Gaussian randomly rough surfaces, and the Kirchhoff Approximation is used to calculate the scattered light intensity distribution from random metal and dielectric rough surfaces. The three characteristics of the scattered light intensity distribution peak, the intensity distribution width and the position of peak are reviewed. Numerical calculation results show that significant differences between scattering characteristics of metal surfaces and the dielectric surfaces exist. The light scattering characteristics are jointly influenced by the slope distribution and reflectance of surface element. The scattered light intensity distribution is affected by common influence of surface local slope distribution and surface local reflectivity. The results can provide a basis theory for the research to lidar target surface scattering characteristics.

Recent advances in study of uranium surface chemistry in China

International Nuclear Information System (INIS)

Luo, Lizhu; Lai, Xinchun; Wang, Xiaolin

2014-01-01

Uranium is very important in nuclear energy industry; however, uranium and its alloys corrode seriously in various atmospheres because of their chemical reactivities. In China, continuous investigations focused on surface chemistry have been carried out for a thorough understanding of uranium in order to provide technical support for its engineering applications. Oxidation kinetics of uranium and its alloys in oxidizing atmospheres are in good agreement with those in the literature. In addition to the traditional techniques, non-traditional methods have been applied for oxidation kinetics of uranium, and it has been verified that spectroscopic ellipsometry and X-ray diffraction are effective and nondestructive tools for in situ kinetic studies. The inhibition efficiency of oxidizing gas impurities on uranium hydrogenation is found to follow the order CO 2 > CO > O 2 , and the broadening of XPS shoulders with temperature in depth profile of hydrogenated uranium surface is discussed, which is not mentioned in the literature. Significant progress on surface chemistry of alloyed uranium (U-Nb and U-Ti) in hydrogen atmosphere is reported, and it is revealed that the hydrating nucleation and subsequent growth of alloyed uranium are closely connected with the surface states, underlying metal matrix, and it is microstructure-dependent. In this review, the recent advances in uranium surface chemistry in China, published so far mostly in Chinese language, are briefly summarized. Suggestions for further study are made. (orig.)

Surface study of irradiated sapphires from Phrae Province, Thailand using AFM

Science.gov (United States)

Monarumit, N.; Jivanantaka, P.; Mogmued, J.; Lhuaamporn, T.; Satitkune, S.

2017-09-01

The irradiation is one of the gemstone enhancements for improving the gem quality. Typically, there are many varieties of irradiated gemstones in the gem market such as diamond, topaz, and sapphire. However, it is hard to identify the gemstones before and after irradiation. The aim of this study is to analyze the surface morphology for classifying the pristine and irradiated sapphires using atomic force microscope (AFM). In this study, the sapphire samples were collected from Phrae Province, Thailand. The samples were irradiated by high energy electron beam for a dose of ionizing radiation at 40,000 kGy. As the results, the surface morphology of pristine sapphires shows regular atomic arrangement, whereas, the surface morphology of irradiated sapphires shows the nano-channel observed by the 2D and 3D AFM images. The atomic step height and root mean square roughness have changed after irradiation due to the micro-structural defect on the sapphire surface. Therefore, this study is a frontier application for sapphire identification before and after irradiation.

The use of marine geophysical methods in Geo-Engineering investigations of Dams/ Barrages - a case study of Kosi Barrage

Digital Repository Service at National Institute of Oceanography (India)

Vora, K.H.; Naidu, P.D.

Geophysical Methods in Geo-Engineering Investigations of Dams/ Barrages - A Case Study of Kosi Barrage INTRODUCTION KH. Vora* P. Divakar Naidu* Dams and barrages are such civil engineering structures where foundation is submerged. The impounded water column... etc. Some other on the spot observations using pole and other elementary probing methods are in vogue. However, usually such investigations would provide only a generalised picture based on isolated data. Advent of high technology, developed over...

Surface studies of liquid metals and alloys

International Nuclear Information System (INIS)

Bastasz, Robert

2003-01-01

Liquid metals and alloys have been proposed for use in nuclear fusion reactors to serve as replaceable plasma-facing surfaces that remove particles and heat from reacting plasmas. Several materials are being considered for this purpose including lithium, gallium, and tin as well as some of the alloys made from these elements. In order to better understand the properties of liquid surfaces, the technique of low-energy ion scattering was used to examine the surface composition of several of these materials in vacuum as a function of temperature. Oxygen is found to rapidly segregate to the surface of several metallic liquids. The segregation process can be interpreted using a simple thermodynamic model based on Gibbs theory. In the case of an alloy of Sn and Li, Li also segregates to the liquid surface. This provides a means to produce a surface enriched in Li, which is more plasma compatible than Sn, without the need to handle large quantities of liquid Li. (author)

Studies of non-contact methods for roughness measurements on wood surfaces

International Nuclear Information System (INIS)

Lundberg, I.A.S.; Porankiewicz, B.

1995-01-01

The quality of wood surfaces after different kinds of machining processes is a property of great importance for the wood processing industries. Present work is a study, whose objective was to evaluate different non-contact methods, for measurement of the quality of the wood surfaces by correlating them with stylus tracing. A number of Scots Pine samples were prepared by different kinds of wood machining processing. Surface roughness measurements were performed, utilizing two optical noncontact methods. The results indicate that the laser scan method can measure surface roughness on sawn wood with a sufficient degree of accuracy. (author) [de

Theoretical studies of positron states and annihilation characteristics at the oxidized Cu(100) surface

Energy Technology Data Exchange (ETDEWEB)

Fazleev, N. G. [Department of Physics, Box 19059, University of Texas at Arlington, Arlington Texas 76019 (United States) and Institute of Physics, Kazan Federal University, Kremlevskaya18, Kazan 420008 (Russian Federation); Weiss, A. H. [Department of Physics, Box 19059, University of Texas at Arlington, Arlington Texas 76019 (United States)

2013-04-19

In this work we present the results of theoretical studies of positron surface and bulk states and annihilation probabilities of surface-trapped positrons with relevant core electrons at the oxidized Cu(100) surface under conditions of high oxygen coverage. An ab-initio study of the electronic properties of the Cu(100) missing row reconstructed surface at various on surface and sub-surface oxygen coverages has been performed on the basis of the density functional theory (DFT) using the Dmol3 code and the generalized gradient approximation (GGA). Surface structures in calculations have been constructed by adding oxygen atoms to various surface hollow and sub-surface octahedral sites of the 0.5 monolayer (ML) missing row reconstructed phase of the Cu(100) surface with oxygen coverages ranging from 0.5 to 1.5 ML. The charge redistribution at the surface and variations in atomic structure and chemical composition of the topmost layers associated with oxidation and surface reconstruction have been found to affect the spatial extent and localization of the positron surface state wave function and annihilation probabilities of surface trapped positrons with relevant core electrons. Theoretical results are compared with experimental data obtained from studies of oxidation of the Cu(100) surface using positron annihilation induced Auger electron spectroscopy (PAES). It has been shown that positron annihilation probabilities with Cu 3s and 3p core electrons decrease when total (on-surface and sub-surface) oxygen coverage of the Cu(100) surface increases up to 1 ML. The calculations show that for high oxygen coverage when total oxygen coverage is 1. 5 ML the positron is not bound to the surface.

Experimental Study on Momentum Transfer of Surface Texture in Taylor-Couette Flow

Science.gov (United States)

Xue, Yabo; Yao, Zhenqiang; Cheng, De

2017-05-01

The behavior of Taylor-Couette (TC) flow has been extensively studied. However, no suitable torque prediction models exist for high-capacity fluid machinery. The Eckhardt-Grossmann-Lohse (EGL) theory, derived based on the Navier-Stokes equations, is proposed to model torque behavior. This theory suggests that surfaces are the significant energy transfer interfaces between cylinders and annular flow. This study mainly focuses on the effects of surface texture on momentum transfer behavior through global torque measurement. First, a power-law torque behavior model is built to reveal the relationship between dimensionless torque and the Taylor number based on the EGL theory. Second, TC flow apparatus is designed and built based on the CNC machine tool to verify the torque behavior model. Third, four surface texture films are tested to check the effects of surface texture on momentum transfer. A stereo microscope and three-dimensional topography instrument are employed to analyze surface morphology. Global torque behavior is measured by rotating a multi component dynamometer, and the effects of surface texture on the annular flow behavior are observed via images obtained using a high-speed camera. Finally, torque behaviors under four different surface conditions are fitted and compared. The experimental results indicate that surface textures have a remarkable influence on torque behavior, and that the peak roughness of surface texture enhances the momentum transfer by strengthening the fluctuation in the TC flow.

Collisions of ideal gas molecules with a rough/fractal surface. A computational study.

Science.gov (United States)

Panczyk, Tomasz

2007-02-01

The frequency of collisions of ideal gas molecules (argon) with a rough surface has been studied. The rough/fractal surface was created using random deposition technique. By applying various depositions, the roughness of the surface was controlled and, as a measure of the irregularity, the fractal dimensions of the surfaces were determined. The surfaces were next immersed in argon (under pressures 2 x 10(3) to 2 x 10(5) Pa) and the numbers of collisions with these surfaces were counted. The calculations were carried out using a simplified molecular dynamics simulation technique (only hard core repulsions were assumed). As a result, it was stated that the frequency of collisions is a linear function of pressure for all fractal dimensions studied (D = 2, ..., 2.5). The frequency per unit pressure is quite complex function of the fractal dimension; however, the changes of that frequency with the fractal dimension are not strong. It was found that the frequency of collisions is controlled by the number of weakly folded sites on the surfaces and there is some mapping between the shape of adsorption energy distribution functions and this number of weakly folded sites. The results for the rough/fractal surfaces were compared with the prediction given by the Langmuir-Hertz equation (valid for smooth surface), generally the departure from the Langmuir-Hertz equation is not higher than 48% for the studied systems (i.e. for the surfaces created using the random deposition technique).

A study of surface films formed during maraging

International Nuclear Information System (INIS)

Khan, M.A.; Haq, A.U.; Khan, A.Q.; Waris, J.; Suleman, M.

1993-01-01

A study was carried out on thin films produced during maraging at 480 deg. 0 C for 3 hours in vacuum (of the order of 10/sup -4/ torr) and in N/ sub 2/ atmosphere. These surface films have been analyzed by Auger electron spectroscopy. Depth profiling for chemical analysis was performed after Ar /sup +/ ion sputtering to predict the compounds formed on the sample surface under prevailing conditions. It was noted that O/sub 2/N/sub 2/ and C are the main constituents of the top layers. These are considered as impurities in the films. Depth profiling showed a smooth interface between the N/sub 2/ and Ti and formation of Titanium nitride is predicted. (author)

Study on surface defects in milling Inconel 718 super alloy

Energy Technology Data Exchange (ETDEWEB)

Chang, Liu; Chengzu, Ren; Guofeng, Wang; Yinwei, Yang; Lu, Zhang [Tianjin University, Tianjin (China)

2015-04-15

Nickel-based alloys have been extensively used as critical components in aerospace industry, especially in the key section of aero engine. In general, these sections are manufactured by milling process because most of them have complex forms. However, surface defects appear frequently in milling due to periodic impact force, which leads to the deterioration of the fatigue life. We conducted milling experiments under different cutting conditions and found that four kinds of defects, i.e., tear, cavity, build up edge (BUE) and groove, commonly appear on the machined surface. Based on the observed results, the morphology and generation regime of these defects are analyzed and the carbide particle cracking is discussed to explain the appearance of the nickel alloy defects. To study the effect of the cutting parameters on the severity of these surface defects, two qualitative indicators, which are named as average number of the defects per field and average area ratio of the defects per field, are presented and the influence laws are summarized based on the results correspondingly. This study is helpful for understanding the generation mechanism of the surface defects during milling process of nickel based super alloy.

DNA adsorption and desorption on mica surface studied by atomic force microscopy

Energy Technology Data Exchange (ETDEWEB)

Sun Lanlan [State Key Laboratory of Electroanalytical Chemistry, Changchun Institute of Applied Chemistry, Graduate school of the Chinese Academy of Sciences, Chinese Academy of Sciences, Renmin Street 5625, Changchun 130022 (China); Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16 East Nan-Hu Road, Open Economic Zone, Changchun 130033 (China); Zhao Dongxu [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16 East Nan-Hu Road, Open Economic Zone, Changchun 130033 (China); Zhang Yue; Xu Fugang [State Key Laboratory of Electroanalytical Chemistry, Changchun Institute of Applied Chemistry, Graduate school of the Chinese Academy of Sciences, Chinese Academy of Sciences, Renmin Street 5625, Changchun 130022 (China); Li Zhuang, E-mail: zli@ciac.jl.cn [State Key Laboratory of Electroanalytical Chemistry, Changchun Institute of Applied Chemistry, Graduate school of the Chinese Academy of Sciences, Chinese Academy of Sciences, Renmin Street 5625, Changchun 130022 (China)

2011-05-15

The adsorption of DNA molecules on mica surface and the following desorption of DNA molecules at ethanol-mica interface were studied using atomic force microscopy. By changing DNA concentration, different morphologies on mica surface have been observed. A very uniform and orderly monolayer of DNA molecules was constructed on the mica surface with a DNA concentration of 30 ng/{mu}L. When the samples were immersed into ethanol for about 15 min, various desorption degree of DNA from mica (0-99%) was achieved. It was found that with the increase of DNA concentration, the desorption degree of DNA from the mica at ethanol-mica interface decreased. And when the uniform and orderly DNA monolayers were formed on the mica surface, almost no DNA molecule desorbed from the mica surface in this process. The results indicated that the uniform and orderly DNA monolayer is one of the most stable DNA structures formed on the mica surface. In addition, we have studied the structure change of DNA molecules after desorbed from the mica surface with atomic force microscopy, and found that the desorption might be ascribed to the ethanol-induced DNA condensation.

A Monte Carlo study of adsorption of random copolymers on random surfaces

CERN Document Server

Moghaddam, M S

2003-01-01

We study the adsorption problem of a random copolymer on a random surface in which a self-avoiding walk in three dimensions interacts with a plane defining a half-space to which the walk is confined. Each vertex of the walk is randomly labelled A with probability p sub p or B with probability 1 - p sub p , and only vertices labelled A are attracted to the surface plane. Each lattice site on the plane is also labelled either A with probability p sub s or B with probability 1 - p sub s , and only lattice sites labelled A interact with the walk. We study two variations of this model: in the first case the A-vertices of the walk interact only with the A-sites on the surface. In the second case the constraint of selective binding is removed; that is, any contact between the walk and the surface that involves an A-labelling, either from the surface or from the walk, is counted as a visit to the surface. The system is quenched in both cases, i.e. the labellings of the walk and of the surface are fixed as thermodynam...

DNA adsorption and desorption on mica surface studied by atomic force microscopy

International Nuclear Information System (INIS)

Sun Lanlan; Zhao Dongxu; Zhang Yue; Xu Fugang; Li Zhuang

2011-01-01

The adsorption of DNA molecules on mica surface and the following desorption of DNA molecules at ethanol-mica interface were studied using atomic force microscopy. By changing DNA concentration, different morphologies on mica surface have been observed. A very uniform and orderly monolayer of DNA molecules was constructed on the mica surface with a DNA concentration of 30 ng/μL. When the samples were immersed into ethanol for about 15 min, various desorption degree of DNA from mica (0-99%) was achieved. It was found that with the increase of DNA concentration, the desorption degree of DNA from the mica at ethanol-mica interface decreased. And when the uniform and orderly DNA monolayers were formed on the mica surface, almost no DNA molecule desorbed from the mica surface in this process. The results indicated that the uniform and orderly DNA monolayer is one of the most stable DNA structures formed on the mica surface. In addition, we have studied the structure change of DNA molecules after desorbed from the mica surface with atomic force microscopy, and found that the desorption might be ascribed to the ethanol-induced DNA condensation.

[Clinical and microbiological study regarding surface antibacterial properties of bioactive dental materials].

Science.gov (United States)

Târcă, T; Bădescu, Aida; Topoliceanu, C; Lăcătuşu, St

2010-01-01

In the new era of dentistry the coronal restoration materials must possess "bio-active" features represented by fluor ions release, chemical adhesion and antibacterial agents. Our study aims to determine the surface antibacterial properties of glassionomer cements and compomers. The study group included 64 patients with high cariogenic risk with 80 teeth with acute and chronic dental caries affecting proximal and occlusal dental surfaces. The teeth with cariogenic lesions were restored with zinc-oxide-eugenol (n=20), glassionomer cement GC Fuji Triage (n=20), glassionomer cement modified with resins Fuji II LC (n=20), compomer Dyract (n=20). DENTOCULT SM test (Orion Diagnostica, Finland) was used for bacterial analyses. The samples from bacterial biofilm were collected from the restorated dental surfaces (study group) and intact enamel surfaces (control group). The recorded data were processed using non-parametrical statistical tests. The lowest mean value of bacterial indices was recorded for glassionomer cement Fuji Triage (0.4), and Fuji II LC (1.2), material with highest surface antibacterial properties. The highest value (1.5) was recorded for compomer Dyract. The Kruskal-Wallis test proves the significant statistical differences between the three bioactive materials. The materials with bioactive features have the ability to inhibate the growth of Streptococcus mutans in bacterial biofilm to the surfaces of coronal restoration.

Field performance assessment of synthetic liners for uranium tailings ponds: a status report

International Nuclear Information System (INIS)

Mitchell, D.H.; Spanner, G.E.

1984-03-01

The objective of this study is to provide a database to support US Nuclear Regulatory Commission (NRC) licensing of uranium tailings leachate isolation impoundments. This objective is being accomplished by determining the effectiveness of design, installation, and quality assurance practices associated with uranium mill tailings impoundments with flexible membrane liners. The program includes testing of chemical resistance and physical performance of liners, leak detection systems, and seam inspection techniques. This report presents the status of the program through September 1983. The report addresses impoundment design, installation, and inspection techniques used by the uranium milling industry. To determine the relative successes of these techniques, information has been collected from consultants, mill operators, and the synthetic liner industry. Progress in experimental tasks on chemical resistance of liners, physical properties of liners, and nondestructive examination of seams is reported. 25 references, 9 figures, 13 tables

Three Gorges Dam alters the Changjiang (Yangtze) river water cycle in the dry seasons: Evidence from H-O isotopes

Energy Technology Data Exchange (ETDEWEB)

Deng, Kai [School of Ocean and Earth Science, Tongji University, Shanghai, 200092 (China); State Key Laboratory of Marine Geology, Tongji University, Shanghai 200092 (China); Yang, Shouye, E-mail: syyang@tongji.edu.cn [State Key Laboratory of Marine Geology, Tongji University, Shanghai 200092 (China); Laboratory for Marine Geology, Qingdao National Laboratory for Marine Science and Technology, Qingdao 266061 (China); Lian, Ergang [School of Ocean and Earth Science, Tongji University, Shanghai, 200092 (China); State Key Laboratory of Marine Geology, Tongji University, Shanghai 200092 (China); Li, Chao [State Key Laboratory of Marine Geology, Tongji University, Shanghai 200092 (China); Yang, Chengfan; Wei, Hailun [School of Ocean and Earth Science, Tongji University, Shanghai, 200092 (China); State Key Laboratory of Marine Geology, Tongji University, Shanghai 200092 (China)

2016-08-15

As the largest hydropower project in the world, the Three Gorges Dam (TGD) has attracted great concerns in terms of its impact on the Changjiang (Yangtze) River and coastal marine environments. In this study, we measured or collected the H-O isotopic data of river water, groundwater and precipitation in the mid-lower Changjiang catchment during the dry seasons of recent years. The aim was to investigate the changes of river water cycle in response to the impoundment of the TGD. Isotopic evidences suggested that the mid-lower Changjiang river water was ultimately derived from precipitation, but dominated by the mixing of different water masses with variable sources and isotopic signals as well. The isotopic parameter “deuterium excess” (d-excess) yielded large fluctuations along the mid-lower mainstream during the initial stage of the TGD impoundment, which was inherited from the upstream water with inhomogeneous isotopic signals. However, as the reservoir water level rising to the present stage, small variability of d-excess was observed along the mid-lower mainstream. This discrepancy could be explained that the TGD impoundment had significantly altered the water cycle downstream the dam, with the rising water level increasing the residence time and enhancing the mixing of reservoir water derived from upstream. This eventually resulted in the homogenization of reservoir water, and thus small fluctuations of d-excess downstream the dam after the quasi-normal stage (2008 to present). We infer that the retention effect of large reservoirs has greatly buffered the d-excess natural variability of water cycle in large river systems. Nevertheless, more research attention has to be paid to the damming effect on the water cycle in the river, estuarine and coastal areas, especially during the dry seasons. - Highlights: • Stable H-O isotopes indicate the Changjiang river water cycle in dry seasons. • The isotopic parameter “d-excess” reveals the origins of

Three Gorges Dam alters the Changjiang (Yangtze) river water cycle in the dry seasons: Evidence from H-O isotopes

International Nuclear Information System (INIS)

Deng, Kai; Yang, Shouye; Lian, Ergang; Li, Chao; Yang, Chengfan; Wei, Hailun

2016-01-01

As the largest hydropower project in the world, the Three Gorges Dam (TGD) has attracted great concerns in terms of its impact on the Changjiang (Yangtze) River and coastal marine environments. In this study, we measured or collected the H-O isotopic data of river water, groundwater and precipitation in the mid-lower Changjiang catchment during the dry seasons of recent years. The aim was to investigate the changes of river water cycle in response to the impoundment of the TGD. Isotopic evidences suggested that the mid-lower Changjiang river water was ultimately derived from precipitation, but dominated by the mixing of different water masses with variable sources and isotopic signals as well. The isotopic parameter “deuterium excess” (d-excess) yielded large fluctuations along the mid-lower mainstream during the initial stage of the TGD impoundment, which was inherited from the upstream water with inhomogeneous isotopic signals. However, as the reservoir water level rising to the present stage, small variability of d-excess was observed along the mid-lower mainstream. This discrepancy could be explained that the TGD impoundment had significantly altered the water cycle downstream the dam, with the rising water level increasing the residence time and enhancing the mixing of reservoir water derived from upstream. This eventually resulted in the homogenization of reservoir water, and thus small fluctuations of d-excess downstream the dam after the quasi-normal stage (2008 to present). We infer that the retention effect of large reservoirs has greatly buffered the d-excess natural variability of water cycle in large river systems. Nevertheless, more research attention has to be paid to the damming effect on the water cycle in the river, estuarine and coastal areas, especially during the dry seasons. - Highlights: • Stable H-O isotopes indicate the Changjiang river water cycle in dry seasons. • The isotopic parameter “d-excess” reveals the origins of

A Study on Water Surface Profiles of Rivers with Constriction

Science.gov (United States)

Qian, Chaochao; Yamada, Tadashi

2013-04-01

Water surface profile of rivers with constrictions is precious in both classic hydraulics and river management practice. This study was conducted to clarify the essences of the water surface profiles. 3 cases of experiments and 1D numerical calculations with different discharges were made in the study and analysis solutions of the non-linear basic equation of surface profile in varied flow without considering friction were derived. The manning's number was kept in the same in each case by using crosspiece roughness. We found a new type of water surface profile of varied flow from the results of 1D numerical calculation and that of experiments and named it as Mc curve because of its mild condition with constriction segment. This kind of curves appears as a nature phenomenon ubiquitously. The process of water surface forming is dynamic and bore occurs at the upper side of constriction during increasing discharge before the surface profile formed. As a theoretical work, 3 analysis solutions were derived included 2 physical-meaning solutions in the study by using Man-Machine system. One of the derived physical-meaning solutions was confirmed that it is validity by comparing to the results of 1D numerical calculation and that of experiments. The solution represents a flow profile from under critical condition at the upper side to super critical condition at the down side of constriction segment. The other derived physical-meaning solution represents a flow profile from super critical condition at the upper side to under critical condition at the down side of constriction segment. These two kinds of flow profiles exist in the nature but no theoretical solution can express the phenomenon. We find the depth distribution only concerned with unit width discharge distribution and critical depth under a constant discharge from the derived solutions. Therefor, the profile can be gained simply and precisely by using the theoretical solutions instead of numerical calculation even

Optical studies of cobalt implanted rutile TiO2 (110) surfaces

International Nuclear Information System (INIS)

Joshi, Shalik Ram; Padmanabhan, B.; Chanda, Anupama; Mishra, Indrani; Malik, V.K.; Mishra, N.C.; Kanjilal, D.; Varma, Shikha

2016-01-01

Highlights: • The present study displays formation of nanostructures after Co implantation on TiO 2 surfaces. • Preferential sputtering leads to the creation of oxygen vacancies on the surface. • A large enhancement in visible light absorbance (nearly 5 times compared to pristine) is observed. • Creation of self-organized nanostructures and Ti 3+ oxygen vacancies promote photoabsorption. • Formation of Co-nanoclusters and Co–Ti–O phase play concerted role in enhancing photo-absorption. - Abstract: Present study investigates the photoabsorption properties of single crystal rutile TiO 2 (110) surfaces after they have been implanted with low fluences of cobalt ions. The surfaces, after implantation, demonstrate fabrication of nanostructures and anisotropic nano-ripple patterns. Creation of oxygen vacancies (Ti 3+ states), development of cobalt nano-clusters as well as band gap modifications have also been observed. Results presented here demonstrate that fabrication of self organized nanostructures, upon implantation, along with the development of oxygen vacancies and ligand field transitions of cobalt ion promote the enhancement of photo-absorbance in both UV (∼2 times) and visible (∼5 times) regimes. These investigations on nanostructured TiO 2 surfaces can be important for photo-catalysis.

Slope failures in surface mines, methods of studying landslides

Energy Technology Data Exchange (ETDEWEB)

Flisiak, J; Korman, S; Mazurek, J

1977-01-01

This paper presents a review of methods of measuring landslide fissures, displacement of ground surface points in the landslide area and of points inside the landslide. An analysis of the landslide process is given, stressing various stages and phases of a landslide. Studies carried out by the Institute of Mining Geomechanics of the Technical University of Mining and Metallurgy in Cracow are evaluated. The studies concentrated on the final state of slopes in brown coal surface mines after a landslide occurs. The necessity of developing an apparatus for continuous recording of displacements of points on a landslide surface is stressed. An apparatus developed by the Institute and used for continuous measuring and recording of displacements is described. The apparatus is used to measure displacements of points during the initial phase of a landslide and during the phase of the largest displacements. The principle of the system consists in locating a number of observation points on the ground and a slope. The points are connected among themselves by flexible connectors. The connectors are equipped with potentiometric transmitters which transform the relative displacements into electric pulses. These pulses are recorded by a conventional recording apparatus. (55 refs.) (In Polish)

Recent advances in study of uranium surface chemistry in China

Energy Technology Data Exchange (ETDEWEB)

Luo, Lizhu; Lai, Xinchun [Science and Technology on Surface Physics and Chemistry Laboratory, Sichuan (China); Wang, Xiaolin [China Academy of Engineering Physics, Sichuan (China)

2014-04-01

Uranium is very important in nuclear energy industry; however, uranium and its alloys corrode seriously in various atmospheres because of their chemical reactivities. In China, continuous investigations focused on surface chemistry have been carried out for a thorough understanding of uranium in order to provide technical support for its engineering applications. Oxidation kinetics of uranium and its alloys in oxidizing atmospheres are in good agreement with those in the literature. In addition to the traditional techniques, non-traditional methods have been applied for oxidation kinetics of uranium, and it has been verified that spectroscopic ellipsometry and X-ray diffraction are effective and nondestructive tools for in situ kinetic studies. The inhibition efficiency of oxidizing gas impurities on uranium hydrogenation is found to follow the order CO{sub 2} > CO > O{sub 2}, and the broadening of XPS shoulders with temperature in depth profile of hydrogenated uranium surface is discussed, which is not mentioned in the literature. Significant progress on surface chemistry of alloyed uranium (U-Nb and U-Ti) in hydrogen atmosphere is reported, and it is revealed that the hydrating nucleation and subsequent growth of alloyed uranium are closely connected with the surface states, underlying metal matrix, and it is microstructure-dependent. In this review, the recent advances in uranium surface chemistry in China, published so far mostly in Chinese language, are briefly summarized. Suggestions for further study are made. (orig.)

Surface physics studied by means of scanning tunneling microscopy

International Nuclear Information System (INIS)

Besenbacher, F.; Laegsgaard, E.; Stensgaard, I.

1993-01-01

Scanning tunneling microscopy has been applied to study silicon crystal structures, oxygen on Cu (110), and real industrial catalyst surfaces. For the latter purpose an Atomic Force Microscope is being developed. (EG)

Surface plasmon enhanced interfacial electron transfer and resonance Raman, surface-enhanced resonance Raman studies of cytochrome C mutants

Energy Technology Data Exchange (ETDEWEB)

Zheng, Junwei [Iowa State Univ., Ames, IA (United States)

1999-11-08

Surface plasmon resonance was utilized to enhance the electron transfer at silver/solution interfaces. Photoelectrochemical reductions of nitrite, nitrate, and CO₂ were studied on electrochemically roughened silver electrode surfaces. The dependence of the photocurrent on photon energy, applied potential and concentration of nitrite demonstrates that the photoelectrochemical reduction proceeds via photoemission process followed by the capture of hydrated electrons. The excitation of plasmon resonances in nanosized metal structures resulted in the enhancement of the photoemission process. In the case of photoelectrocatalytic reduction of CO₂, large photoelectrocatalytic effect for the reduction of CO₂ was observed in the presence of surface adsorbed methylviologen, which functions as a mediator for the photoexcited electron transfer from silver metal to CO₂ in solution. Photoinduced reduction of microperoxidase-11 adsorbed on roughened silver electrode was also observed and attributed to the direct photoejection of free electrons of silver metal. Surface plasmon assisted electron transfer at nanostructured silver particle surfaces was further determined by EPR method.

Studies of high coverage oxidation of the Cu(100) surface using low energy positrons

Science.gov (United States)

Fazleev, N. G.; Maddox, W. B.; Weiss, A. H.

2012-02-01

The study of oxidation of single crystal metal surfaces is important in understanding the corrosive and catalytic processes associated with thin film metal oxides. The structures formed on oxidized transition metal surfaces vary from simple adlayers of chemisorbed oxygen to more complex structures which result from the diffusion of oxygen into subsurface regions. In this work we present the results of theoretical studies of positron surface and bulk states and annihilation probabilities of surface-trapped positrons with relevant core electrons at the oxidized Cu(100) surface under conditions of high oxygen coverage. Calculations are performed for various high coverage missing row structures ranging between 0.50 and 1.50 ML oxygen coverage. The results of calculations of positron binding energy, positron work function, and annihilation characteristics of surface trapped positrons with relevant core electrons as function of oxygen coverage are compared with experimental data obtained from studies of oxidation of the Cu(100) surface using positron annihilation induced Auger electron spectroscopy (PAES).

Coupling between bulk ordering and surface segregation: from alloy surfaces to surface alloys

International Nuclear Information System (INIS)

Gallis, Coralie

1997-01-01

-The knowledge of the alloy surfaces is of prime interest to understand their catalytic properties. On the one hand, the determination of the stability of the surface alloys depends very strongly on the behaviours of the A c B 1-c alloy surfaces. On the other hand, the knowledge of the kinetics of the formation-dissolution of surface alloys can allow to understand the equilibrium segregation isotherm. We have then studied the relation between the equilibrium surface segregation in an alloy A c B 1-c and the kinetics of dissolution of a few metallic layers of A/B and the inverse deposit. We have used an energetic model derived from the electronic structure (T.I.B.M.) allowing us to study the surface segregation both in the disordered state and in the ordered one. The kinetics of dissolution were studied using the kinetic version of this model (K.T.I.B.M.) consistent with the equilibrium model. To illustrate our study, we have chosen the Cu-Pd system, a model for the formation of surface alloys and for which a great number of studies, both experimental and theoretical, are in progress. We then have shown for the (111) surface of this system that the surface alloys obtained during the dissolution are related to the alloy surfaces observed for the equilibrium segregation. The Cu-Pd system is characteristic of systems which have a weak segregation energy. Then, we have performed an equivalent study for a system with a strong segregation energy. Our choice was directly put on the Pt-Sn system. The surface behaviour, both in equilibrium and during the kinetics of dissolution, is very different from the Cu-Pd case. In particular, we have found pure 2-D surface alloys. Finally, a quenched molecular dynamics study has allowed us to determine the relative stability of various possible surface superstructures. (author) [fr

First-principles study of the surface properties of U-Mo system

Energy Technology Data Exchange (ETDEWEB)

Mei, Zhi-Gang; Liang, Linyun; Yacout, Abdellatif M.

2018-02-01

U-Mo alloys are promising fuels for future high-performance research reactors with low enriched uranium. Surface properties, such as surface energy, are important inputs for mesoscale simulations (e.g., phase field method) of fission gas bubble behaviors in irradiated nuclear fuels. The lack of surface energies of U-Mo alloys prevents an accurate modeling of the morphology of gas bubbles and gas bubble-induced fuel swelling. To this end, we study the surface properties of U-Mo system, including bcc Mo, alpha-U, gamma-U, and gamma U-Mo alloys. All surfaces up to a maximum Miller index of three and two are calculated for cubic Mo and gamma-U and non-cubic alpha-U, respectively. The equilibrium crystal shapes of bcc Mo, alpha-U and gamma-U are constructed using the calculated surface energies. The dominant surface orientations and the area fraction of each facet are determined from the constructed equilibrium crystal shape. The disordered gamma U-Mo alloys are simulated using the Special Quasirandom Structure method. The (1 1 0) and (1 0 0) surface energies of gamma U-7Mo and U-10Mo alloys are predicted to lie between those of gamma-U and bcc Mo, following a linear combination of the two constituents' surface energies. To better compare with future measurements of surface energies, the area fraction weighted surface energies of alpha-U, gamma-U and gamma U-7Mo and U-10Mo alloys are also predicted. (C) 2017 Published by Elsevier B.V.

Study on the surface oxidation of uranium in different gaseous atmospheres

International Nuclear Information System (INIS)

Wang Xiaoling; Fu Yibei; Xie Renshou

1996-03-01

The studying for the surface oxidation of uranium and oxide by X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES), secondary ion mass spectroscopy (SIMS), and the surface oxidation of uranium in different gaseous atmospheres such as O 2 , H 2 , CO, CO 2 , H 2 O(v) and air were reviewed. The surface oxidation of uranium is greatly influenced by a number of parameters including atmospheric temperature, pressure, diffusion of adsorbed gas atoms through the oxide layer, surface and interface chemical component, and defect structure and electron nature of the oxide layer. The initial oxidation mechanism and kinetics have been discussed. Suggestions for future work have also been presented. (32 refs., 7 figs., 5 tabs.)

In situ diffraction studies of electrode surface structure during gold electrodeposition

International Nuclear Information System (INIS)

Magnussen, O.M.; Krug, K.; Ayyad, A.H.; Stettner, J.

2008-01-01

Surface X-ray scattering (SXS) in transmission geometry provides a valuable tool for in situ structural studies of electrochemical interfaces under reaction conditions, as illustrated here for homoepitaxial electrodeposition on Au(1 0 0) and Au(1 1 1) electrodes. Employing diffusion-limited deposition conditions to separate the effects of potential and deposition rate, a mutual interaction between the interface structure and the growth behavior is found. Time-dependent SXS measurements during Au(1 0 0) homoepitaxy show with decreasing potential transitions from step flow to layer-by-layer growth, then to multilayer growth, and finally back to layer-by-layer growth. This complex growth behavior can be explained within the framework of kinetic growth theory by the effect of potential, Cl adsorbates and the Au surface structure, specifically the presence of the surface reconstruction, on the Au surface mobility. Conversely, the electrodeposition process influences the structure of the reconstructed Au surface, as illustrated for Au(1 1 1), where a significant deposition-induced compression of the Au surface layer as compared to Au(1 1 1) surfaces under ultrahigh vacuum conditions or in Au-free electrolyte is found. This compression increases towards more negative potentials, which may be explained by a release of potential-induced surface stress

Surface Decontamination Studies of Cs-137 and Sr-85 Using Polymer Gel

International Nuclear Information System (INIS)

Pham, L.; Nguyen, C.; Nguyen, L.

2015-01-01

Strippable polymer coating is one of the methods for effective surface decontamination to remove isotopes on the contaminated surface. This method is applying in nuclear facilities on the World. In this paper, we present the results obtained in our laboratory from product the polymer coating to apply to remove radioisotopes of "1"3"7Cs and "8"5Sr from surface of glass, stainless steel, mild steel, ceramic, PVC plastic. This polymer gel solution consist of water soluble polymer preferably polyvinyl alcohol (PVA), plasticizing agent (glycerine) and chelating agents, (citric acid) which can be sprayed or pasted on to contaminated surface. After some hours, these gel solutions was dried to form a strong thin film and it was easily peeled off from a contaminated surface with the radioactive isotopes and can be disposed off as radioactive solid waste. In this study infrared spectrophotometry technique was used to examine the interaction of the cesium and strontium ions with polyvinyl alcohol (PVA), polymer gel and the results of the study were also presented. The results showed that decontamination efficiency of "1"3"7Cs and "8"5Sr strongly depended on property, porosity and smoothness of the contaminated surface and obtained from 95-99% on glass and stainless steel, ceramic and PVC plastic surfaces. The decontamination efficiency also depended on activity and coating thickness. Optimization of film thickness is around 0.2 mm. Decontamination efficiency of Polymer gel were compared with Decongel 1101 (product from USA) on surfaces. IR spectra studies indicated that Cs and Sr ions interacted with PVA and citric acid in Polymer gel through cacboxyl (C = O) group. Polymer gel could remove of "1"3"7Cs and "8"5Sr better than PVA gel does because of citric acid, which can form chelating complex with Cs and Sr ion. (author)

40 CFR 421.62 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Science.gov (United States)

2010-07-01

... precipitation for the month that falls within the impoundment and either the evaporation from the pond water... precipitation for that month that falls within the impoundment and the mean evaporation from the pond water...

Behind adhesion of uranyl onto montmorillonite surface: A molecular dynamics study

Energy Technology Data Exchange (ETDEWEB)

Yang, W.; Zaoui, A., E-mail: azaoui@polytech-lille.fr

2013-10-15

Highlights: • We investigated the adsorption of uranyl onto Montmorillonite surface. • We studied the surface energy between layered Montmorillonite sheets. • We studied the work of adhesion between radionuclide and charged Montmorillonite. -- Abstract: We have performed molecular dynamics simulations to investigate the adsorption of radionuclide elements species onto substituted Montmorillonite (001) surface in the presence of different counterions. The structure and the dynamics of uranyl ion as well as its aquo, chloride ion, and carbonate complexes are analyzed. In addition, we have studied the surface energy between layered Montmorillonite sheets and the work of adhesion between radionuclide and charged Montmorillonite. The clay model used here is a Wyoming-type Montmorillonite with 0.75e negative charge per unit cell resulting from substitutions in Octahedral and Tetrahedral sheets. The system model was constructed based on CLAYFF force field potential model. To evaluate the thermodynamic work of adhesion, each surface and clay layer regions are converted to a thin film model. One and two species of radionuclide elements (UO{sub 2}(H{sub 2}O){sub 5},UO{sub 2}CO{sub 3}(H{sub 2}O){sub 5}, and UO{sub 2}Cl{sub 2}(H{sub 2}O){sub 5}) were deposited near the clay surface in a pseudo-two-dimensional periodic cell. Analysis shows that the uranyl ion structure is preserved with two axial oxygen atoms detected at 1.8 Å. Radial distribution functions results indicate that average U-O{sub w} distances are 2.45–2.61 Å, and 2.29–2.40 Å for U-O{sub c} distance. Average U-Cl distances are 2.78–3.08 Å, which is relatively larger than that of Uranium atom-Oxygen atom because of electrostatic factors.

Combined sputtering yield and surface topography development studies on Si

International Nuclear Information System (INIS)

Carter, G.; Nobes, M.J.; Lewis, G.W.; Whitton, J.L.

1981-01-01

The sputtering yield-incidence angle function has been measured for 8 keV Ar + ions incident on Si by direct scanning electron microscope observation of the depths of sputtered craters on substrate boundaries. This function displays a maximum sputtering yield at an angle thetasub(p) approximately equal to 40 0 to the surface normal. The sequential ion fluence dependence of features developed beneath local surface contaminant was then studied, quasi dynamically, in the same on-line ion source-S.E.M. system. During erosion of the contaminant a steeply elevated pillar of Si forms, which then transforms to a cone, again of high elevation angle >>thetasub(p). This cone is gradually eroded into the surrounding surface with no special significance associated with orientations of angle thetasub(p). Pedal depressions surrounding the pillar-cone system are also noted. The reasons for these observations and their relevance to ion beam surface channel etching are discussed. (Auth.)

In situ ellipsometric study of surface immobilization of flagellar filaments

Energy Technology Data Exchange (ETDEWEB)

Kurunczi, S., E-mail: kurunczi@mfa.kfki.hu [Department of Photonics, Research Institute for Technical Physics and Materials Science, H-1121, Konkoly Thege Miklos ut 29-33, Budapest (Hungary); Nemeth, A.; Huelber, T. [Department of Photonics, Research Institute for Technical Physics and Materials Science, H-1121, Konkoly Thege Miklos ut 29-33, Budapest (Hungary); Kozma, P. [Department of Photonics, Research Institute for Technical Physics and Materials Science, H-1121, Konkoly Thege Miklos ut 29-33, Budapest (Hungary); Department of Nanotechnology, Research Institute of Chemical and Process Engineering, Faculty of Information Technology, University of Pannonia, Egyetem u. 10, Veszprem, H-8200 (Hungary); Petrik, P. [Department of Photonics, Research Institute for Technical Physics and Materials Science, H-1121, Konkoly Thege Miklos ut 29-33, Budapest (Hungary); Jankovics, H. [Department of Nanotechnology, Research Institute of Chemical and Process Engineering, Faculty of Information Technology, University of Pannonia, Egyetem u. 10, Veszprem, H-8200 (Hungary); Sebestyen, A. [Department of Photonics, Research Institute for Technical Physics and Materials Science, H-1121, Konkoly Thege Miklos ut 29-33, Budapest (Hungary); Department of Nanotechnology, Research Institute of Chemical and Process Engineering, Faculty of Information Technology, University of Pannonia, Egyetem u. 10, Veszprem, H-8200 (Hungary); Vonderviszt, F. [Department of Photonics, Research Institute for Technical Physics and Materials Science, H-1121, Konkoly Thege Miklos ut 29-33, Budapest (Hungary); Department of Nanotechnology, Research Institute of Chemical and Process Engineering, Faculty of Information Technology, University of Pannonia, Egyetem u. 10, Veszprem, H-8200 (Hungary); Institute of Enzymology, Karolina ut 29-33, Budapest, H-1113 (Hungary); and others

2010-10-15

Protein filaments composed of thousands of subunits are promising candidates as sensing elements in biosensors. In this work in situ spectroscopic ellipsometry is applied to monitor the surface immobilization of flagellar filaments. This study is the first step towards the development of layers of filamentous receptors for sensor applications. Surface activation is performed using silanization and a subsequent glutaraldehyde crosslinking. Structure of the flagellar filament layers immobilized on activated and non-activated Si wafer substrates is determined using a two-layer effective medium model that accounted for the vertical density distribution of flagellar filaments with lengths of 300-1500 nm bound to the surface. The formation of the first interface layer can be explained by the multipoint covalent attachment of the filaments, while the second layer is mainly composed of tail pinned filaments floating upwards with the free parts. As confirmed by atomic force microscopy, covalent immobilization resulted in an increased surface density compared to absorption.

Mine Waste Disposal and Managements

Energy Technology Data Exchange (ETDEWEB)

Cheong, Young-Wook; Min, Jeong-Sik; Kwon, Kwang-Soo [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

1999-12-01

This research project deals with: Analysis and characterization of mine waste piles or tailings impoundment abandoned in mining areas; Survey of mining environmental pollution from mine waste impounds; Modelling of pollutants in groundwater around tailings impoundment; Demonstration of acid rock drainage from coal mine waste rock piles and experiment of seeding on waste rock surface; Development of a liner using tailings. Most of mine wastes are deposited on natural ground without artificial liners and capping for preventing contamination of groundwater around mine waste piles or containments. In case of some mine waste piles or containments, pollutants have been released to the environment, and several constituents in drainage exceed the limit of discharge from landfill site. Metals found in drainage exist in exchangeable fraction in waste rock and tailings. This means that if when it rains to mine waste containments, mine wastes can be pollutant to the environment by release of acidity and metals. As a result of simulation for hydraulic potentials and groundwater flow paths within the tailings, the simulated travel paths correlated well with the observed contaminant distribution. The plum disperse, both longitudinal and transverse dimensions, with time. Therefore liner system is a very important component in tailings containment system. As experimental results of liner development using tailings, tailings mixed with some portion of resin or cement may be used for liner because tailings with some additives have a very low hydraulic conductivity. (author). 39 refs.

Scanning Tunneling Microscopy Studies of Surface Structures of Icosahedral Al-Cu-Fe Quasicrystals

Energy Technology Data Exchange (ETDEWEB)

Cai, Tanhong [Iowa State Univ., Ames, IA (United States)

2001-01-01

Three papers are included in this dissertation. The first paper: ''Structural aspects of the fivefold quasicrystalline Al-Cu-Fe surface from STM and dynamical LEED studies'', is in press with ''Surface Science''. The second paper: ''An STM study of the atomic structure of the icosahedral Al-Cu-Fe fivefold surface'' is submitted to ''Physical Review B, Rapid Communication''. The third paper: ''Pseudomorphic starfish: arrangement of extrinsic metal atoms on a quasicrystalline substrate'' is submitted to ''Nature''. Following the third paper are general conclusions and appendices that document the published paper ''Structural aspects of the three-fold surface of icosahedral Al-Pd-Mn'' (appearing in volume 461, issue 1-3 of ''Surface Science'' on page L521-L527, 2000), the design as well as the specifications of the aluminum evaporator used in the aluminum deposition study in this dissertation, an extended discussion of the aluminum deposition on the quasicrystalline surface, and the STM database.

Experimental study of water droplets on over-heated nano/microstructured zirconium surfaces

Energy Technology Data Exchange (ETDEWEB)

Kim, Seol Ha [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Ahn, Ho Seon [Division of Mechanical System Engineering, Incheon National University, 406-772 (Korea, Republic of); Kim, Joonwon [Department of Mechanical Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Kim, Moo Hwan [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Park, Hyun Sun, E-mail: hejsunny@postech.ac.kr [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of)

2014-10-15

Highlights: • Heat transfer performance of a droplet on a modified zirconium surface is evaluated. • Modified (nano/micro-) surfaces enhanced heat transfer rate and Leidenfrost point. • A highly wettable condition of the modified surface contributes the enhancement. • Nano-scaled modification indicates the higher performance of droplet cooling. • Investigation via visualization of the droplet support the heat transfer experimental data. - Abstract: In this study, we observed the behavior of water droplets near the Leidenfrost point (LFP) on zirconium alloy surfaces with anodizing treatment and investigated the droplet cooling performance. The anodized zirconium surface, which consists of bundles of nanotubes (∼10–100 nm) or micro-mountain-like structures, improved the wetting characteristics of the surface. A deionized water droplet (6 μL) was dropped onto test surfaces heated to temperatures ranging from 250 °C to the LFP. The droplet dynamics were investigated through high-speed visualization, and the cooling performance was discussed in terms of the droplet evaporation time. The modified surface provided vigorous, intensive nucleate boiling in comparison with a clean, bare surface. Additionally, we observed that the structured surface had a delayed LFP due to the high wetting condition induced by strong capillary wicking forces on the structured surface.

The impacts of Phalaris arundinacea (reed canary grass) invasion on wetland plant richness in the Oregon Coast Range, USA, depend on beavers

Science.gov (United States)

Perkins, T.; Wilson, M.

2005-01-01

Invasive plants can threaten diversity and ecosystem function. We examined the relationship between the invasive Phalaris arundinacea (reed canarygrass) and species richness in beaver wetlands in Oregon, USA. Four basins (drainages) were chosen and three sites each of beaver impoundments, unimpounded areas and areas upstream of debris jams were randomly chosen in each basin for further study (n = 36). Analysis of covariance (ANCOVA) showed that the relationship between Phalaris and species richness differed significantly (p = 0.01) by site type. Dam sites (beaver impoundments) exhibited a strong inverse relationship between Phalaris and species richness (bD = a??0.15), with one species lost for each 7% increase in Phalaris cover. In contrast, there was essentially no relationship between Phalaris cover and species richness in jam sites (debris jam impoundments formed by flooding; bJ = +0.01) and unimpounded sites (bU = a??0.03). The cycle of beaver impoundment and abandonment both disrupts the native community and provides an ideal environment for Phalaris, which once established tends to exclude development of herbaceous communities and limits species richness. Because beaver wetlands are a dominant wetland type in the Coast Range, Phalaris invasion presents a real threat to landscape heterogeneity and ecosystem function in the region.

30 CFR 780.25 - Reclamation plan: Siltation structures, impoundments, and refuse piles.

Science.gov (United States)

2010-07-01

... is capable of being done after consideration of cost, logistics, and available technology. The fact... COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS SURFACE MINING PERMIT APPLICATIONS-MINIMUM..., and refuse piles. (a) General. Each application must include a general plan and a detailed design plan...

A Study of Atmospheric Plasma Treatment on Surface Energetics of Carbon Fibers

International Nuclear Information System (INIS)

Park, Soo Jin; Chang, Yong Hwan; Moon, Cheol Whan; Suh, Dong Hack; Im, Seung Soon; Kim, Yeong Cheol

2010-01-01

In this study, the atmospheric plasma treatment with He/O 2 was conducted to modify the surface chemistry of carbon fibers. The effects of plasma treatment parameters on the surface energetics of carbon fibers were experimentally investigated with respect to gas flow ratio, power intensity, and treatment time. Surface characteristics of the carbon fibers were determined by X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), Fourier transform infrared (FT-IR), Zeta-potential, and contact angle measurements. The results indicated that oxygen plasma treatment led to a large amount of reactive functional groups onto the fiber surface, and these groups can form together as physical intermolecular bonding to improve the surface wettability with a hydrophilic polymer matrix

Three-dimensional geologic modeling and groundwater flow modeling of the Töllinperä aquifer in the Hitura nickel mine area, Finland – providing the framework for restoration and protection of the aquifer

Directory of Open Access Journals (Sweden)

Sami Saraperä

2004-01-01

Full Text Available Elevated concentrations of sulphate, chloride, and nickel were discovered in water samples taken from the Töllinperä aquifer in western Finland. The area is located adjacent to the tailings area of the Hitura nickel mine. Earlier studies revealed that the groundwater contamination resulted from tailings-derived mine waters leaking from a tailings impoundment area. The tailings area directly overlies the Weichselian esker system, part of which is the Töllinperä classified groundwater area. The observed groundwater and surface water contamination resulted in a need to characterize the subsurface geology in the whole area of the contaminated esker aquifer. The primary sedimentary units were introduced into a three-dimensional (3-D geologic model of the aquifer made with EarthVision geologic modeling software. The information obtained from the 3-D geological model was then introduced into a numerical groundwater flow model made with MODFLOW code, which was calibrated with MODFLOWP code.The results of this study were used to guide the sealing of the tailings impoundment in order to prevent the further contamination of the Töllinperä aquifer. The groundwater flow model was used to interpret and simulate the flow system, and to provide a plan to safely continue water supply to local inhabitants from the unpolluted parts of the aquifer.

75 FR 4362 - Green Island Power Authority; Notice of Application Ready for Environmental Analysis, and...

Science.gov (United States)

2010-01-27

... impoundment elevation to 18.4 feet msl and increase the impoundment size to 708 acres; (4) install a new trash... resource- specific settlement agreement signed by it and the National Marine Fisheries Service, U.S. Fish...

Case Study: Southwest Coastal Louisiana Conceptual Ecosystem Model Development

Science.gov (United States)

2014-08-01

promoted the land-building process. Wave action and occasional storm events also deposited sand and shells onto the newly built land. Alteration of...water into impounded areas results in reduced biomass production and impaired health, which in turn causes increased vegetation mortality, decreased...and biomass in freshwater marshes (Smart and Barko 1980, Linthurst and Seneca 1981, Pezeshki et al 1987, McKee and Mendelssohn 1989, Spalding and

Film mass transfer coefficient for the prediction of volatile organic compound evaporation rate from open water basin

OpenAIRE

Charun Bunyakan; Preyaporn Tongsoi; Chakrit Tongurai

2001-01-01

The evaporation of volatile organic compounds(VOCs) from treatment, storage, disposal facility(TSDF) is an important air pollution issue because of the evaporation quantity and toxicity and/or carcinogenicity. This paper concerns VOC evaporation from open water basins such as the equalization basin and nonaerate surface impoundments in a wastewater treatment plant. The amount of VOCs evaporation from open water basins can be predicted by using the two-film model that requires two mass transfe...

Design, placement, and sampling of groundwater monitoring wells for the management of hazardous waste disposal facilities

International Nuclear Information System (INIS)

Tsai, S.Y.

1988-01-01

Groundwater monitoring is an important technical requirement in managing hazardous waste disposal facilities. The purpose of monitoring is to assess whether and how a disposal facility is affecting the underlying groundwater system. This paper focuses on the regulatory and technical aspects of the design, placement, and sampling of groundwater monitoring wells for hazardous waste disposal facilities. Such facilities include surface impoundments, landfills, waste piles, and land treatment facilities. 8 refs., 4 figs

National Dam Safety Program. No Name 165 (Crystal Lake Dam) (MO 10580), Missouri - Kansas City Basin, Jackson County, Missouri. Phase I Inspection Report.

Science.gov (United States)

1978-07-01

For NTIS GRA&I DTIC TAB >0 Unannounced [D Just ification- D T C ELECTE By Distribution/ NOV 20 1981 Avail and/orS Availabilit CodesD=-Dist Spca D NO...Hutton, Engineering Geologist. Impoundment of water began in 1970. h. Normal Operating Procedure. Normal rainfall, runoff, transpir- ation, and...evaporation all combine to maintain a relatively stable water surface elevation. 1.3 PERTINENT DATA a. Drainage Area - 9,900 acres of which approximately 15

National Dam Safety Program. Lakeview Estates Dam (MO 11004), Mississippi - Kaskaskia - St. Louis Basin, Warren County, Missouri. Phase I Inspection Report.

Science.gov (United States)

1979-09-01

ificatiozh Distributon/ Availabilit oe LAKEVIEW ESTATES DAM WARREN COUNTY, MISSOURI MISSOURI INVENTORY NO. 11004 PHASE I INSPECTION REPORT NATIONAL DAM SAFETY...and *impounds less than 1,000 acre-feet of water . Our inspection and evaluation indicates that the spill- way of Lakeview Estates Dam does not meet...not be measured because of high reservoir level, scalloping near the crest and a berm just under the water surface. Limestone riprap in sizes from sand

Localization of optical excitations on random surfaces: SNOM studies

DEFF Research Database (Denmark)

Bozhevolnyi, Sergey I.

1999-01-01

Localization of optical excitations on nanostructured metal surfaces and fractal colloid silver aggregates are studied by using a scanning near-field optical microscope (SNOM). The SNOM images obtained in both configurations exhibit spatially localized (within 150 to 250 nm) light intensity...

In-situ oxidation study of Pd(100) by surface x-ray diffraction

Energy Technology Data Exchange (ETDEWEB)

Kilic, Volkan; Franz, Dirk; Stierle, Andreas [AG Grenzflaechen, Universitaet Siegen (Germany); Martin, Natalia; Lundgren, Edvin [Department of Synchrotron Radiation Research, Lund University (Sweden); Mantilla, Miguel [MPI fuer Metallforschung, Stuttgart (Germany)

2011-07-01

The oxidation of the Pd(100) surface at oxygen pressures in the 10{sup -6} mbar to 10{sup 3} mbar range and temperatures up to 1000 K has been studied in-situ by surface x-ray diffraction (SXRD). The SXRD experiments were performed at the MPI beamline at the Angstrom Quelle Karlsruhe (ANKA). We present the surface and crystal truncation rod (CTR) data from the ({radical}(5) x {radical}(5)) surface layer. We show that the transformation from the surface oxide to PdO bulk oxide can be observed in-situ under specific pressure and temperature conditions. We compare our results with previously proposed structure models based on low energy electron diffraction (LEED) I(V) curves and density functional theory calculations. Finally, we elucidate the question of commensurability of the surface oxide layer with respect to the Pd(100) substrate.

Theoretical study of adsorption of organic phosphines on transition metal surfaces

Science.gov (United States)

Lou, Shujie; Jiang, Hong

2018-04-01

The adsorption properties of organic phosphines on transition metal (TM) surfaces (Fe, Co, Ni, Cu, Ru, Rh, Pd, Ag, Ir, Pt, and Au) have been studied to explore the possibility of building novel heterogeneous chiral catalytic systems based on organic phosphines. Preferred adsorption sites, adsorption energies and surface electronic structures of a selected set of typical organic phosphines adsorbed on TM surfaces are calculated with density-functional theory to obtain a systematic understanding on the nature of adsorption interactions. All organic phosphines considered are found to chemically adsorb on these TM surfaces with the atop site as the most preferred one, and the TM-P bond is formed via the lone-pair electrons of the P atom and the directly contacted TM atom. These findings imply that it is indeed possible to build heterogeneous chiral catalytic systems based on organic phosphines adsorbed on TM surfaces, which, however, requires a careful design of molecular structure of organic phosphines.

A surface-chemistry study of barium ferrite nanoplates with DBSa-modified surfaces

Energy Technology Data Exchange (ETDEWEB)

Lisjak, Darja, E-mail: darja.lisjak@ijs.si [Jožef Stefan Institute, Ljubljana (Slovenia); Ovtar, Simona; Kovač, Janez [Jožef Stefan Institute, Ljubljana (Slovenia); Gregoratti, Luca; Aleman, Belen; Amati, Matteo [Elettra – Sincrotrone Trieste S.C.p.A. di interesse nazionale, Trieste (Italy); Fanetti, Mattia [University of Nova Gorica, Nova Gorica (Slovenia); Istituto Officina dei Materiali CNR, Area Science Park, Trieste (Italy); Makovec, Darko [Jožef Stefan Institute, Ljubljana (Slovenia)

2014-06-01

Barium ferrite (BaFe{sub 12}O{sub 19}) is a ferrimagnetic oxide with a high magnetocrystalline anisotropy that can be exploited in magnetically aligned ceramics or films for self-biased magnetic applications. Magnetic alignment of the films can be achieved by the directed assembly of barium ferrite nanoplates. In this investigation the nanoplates were synthesized hydrothermally and suspended in 1-butanol using dodecylbenzene sulphonic acid (DBSa) as a surfactant. They were then deposited in an electric or magnetic field on flat substrates and exhibited a significant preferential alignment in the plane of the substrate, allowing a differentiation between the analysis of their basal and side planes using scanning photoelectron microscopy with a lateral resolution down to 100 nm. The surface chemistry of the nanoplates was additionally studied with X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry. For a comparison, bare barium ferrite nanoplates were also analyzed after decomposing the DBSa at 460 °C. The deviation of the surface chemistry from the stoichiometric composition was observed and the adsorption of the DBSa molecules on the nanoplates was confirmed with all three methods. Different types of bonding (physi- or chemisorption) were possible and considered with respect to the assembly of the barium ferrite nanoplates into anisotropic magnetic films.

Study of plasma formation in CW CO2 laser beam-metal surface interaction

Science.gov (United States)

Azharonok, V. V.; Vasilchenko, Zh V.; Golubev, Vladimir S.; Gresev, A. N.; Zabelin, Alexandre M.; Chubrik, N. I.; Shimanovich, V. D.

1994-04-01

An interaction of the cw CO2 laser beam and a moving metal surface has been studied. The pulsed and thermodynamical parameters of the surface plasma were investigated by optical and spectroscopical methods. The subsonic radiation wave propagation in the erosion plasma torch has been studied.

Use of neutrals backscattering for studying the vibrational properties of solid surfaces

International Nuclear Information System (INIS)

Lapujoulade, J.

1975-01-01

The neutrals (rare gases) elastic scattering may be used for studying some interesting properties of surfaces. However, an analysis of inelastic phenomena is mostly to be performed when vibrational properties of metallic surfaces are investigated. The dispersion relation of surface phonons has not yet been experimentally obtained from neutrals backscattering from solid surfaces, but the quasi-elastic scattering of helium should give this information on condition that velocity measurements are refined in view of directly obtained the distribution function rather than its moments and determining the preponderance of one-phonon transitions, or obtaining a detailed description of many-phonon exchanges [fr

Theoretical aspects of studies of oxide and semiconductor surfaces using low energy positrons

Science.gov (United States)

Fazleev, N. G.; Maddox, W. B.; Weiss, A. H.

2011-01-01

This paper presents the results of a theoretical study of positron surface and bulk states and annihilation characteristics of surface trapped positrons at the oxidized Cu(100) single crystal and at both As- and Ga-rich reconstructed GaAs(100) surfaces. The variations in atomic structure and chemical composition of the topmost layers of the surfaces associated with oxidation and reconstructions and the charge redistribution at the surfaces are found to affect localization and spatial extent of the positron surface-state wave functions. The computed positron binding energy, work function, and annihilation characteristics reveal their sensitivity to charge transfer effects, atomic structure and chemical composition of the topmost layers of the surfaces. Theoretical positron annihilation probabilities with relevant core electrons computed for the oxidized Cu(100) surface and the As- and Ga-rich reconstructed GaAs(100) surfaces are compared with experimental ones estimated from the positron annihilation induced Auger peak intensities measured from these surfaces.

TiO₂ Surface Coating of Mn-Zn Dopped Ferrites Study

DEFF Research Database (Denmark)

Solný, Tomáš; Ptacek, Petr; Másilko, Jiří

2016-01-01

This study deals with TiO2 coating of powder Mn-Zn ferrite in order to recieve photocatalytic layer on the top of these particles, forming core-shell catalyst. Powder catalysts are of great advance over the world due to the high surface area, considering the kinetics proceeds through heterogenous...... phase boundary catalysis. However their withdrawal from cleaning systems often requires energetically and economically demanding processes such as filtration and ultrafiltration. Since the ferrite is magnetic, the advantage of such formed core-shell photocatalyst is easibility of removing from...... photocatalytic decomposition system using external magnetic field. In this study the surface coating is performed, using Ti alkoxides mixtures with nanosized TiO2 particles and C and Au coating to form film layer of TiO2 on the surface of ferrite. XRD, SEM – EDS analyses are employed to study surface coating....

Reservoir Greenhouse Gas Emissions at Russian HPP

Energy Technology Data Exchange (ETDEWEB)

Fedorov, M. P.; Elistratov, V. V.; Maslikov, V. I.; Sidorenko, G. I.; Chusov, A. N.; Atrashenok, V. P.; Molodtsov, D. V. [St. Petersburg State Polytechnic University (Russian Federation); Savvichev, A. S. [Russian Academy of Sciences, S. N. Vinogradskii Institute of Microbiology (Russian Federation); Zinchenko, A. V. [A. I. Voeikov Main Geophysical Observatory (Russian Federation)

2015-05-15

Studies of greenhouse-gas emissions from the surfaces of the world’s reservoirs, which has demonstrated ambiguity of assessments of the effect of reservoirs on greenhouse-gas emissions to the atmosphere, is analyzed. It is recommended that greenhouse- gas emissions from various reservoirs be assessed by the procedure “GHG Measurement Guidelines for Fresh Water Reservoirs” (2010) for the purpose of creating a data base with results of standardized measurements. Aprogram for research into greenhouse-gas emissions is being developed at the St. Petersburg Polytechnic University in conformity with the IHA procedure at the reservoirs impounded by the Sayano-Shushenskaya and Mainskaya HPP operated by the RusHydro Co.

Groundwater monitoring strategies at the Weldon Spring site, Weldon Spring, Missouri

International Nuclear Information System (INIS)

Meyer, K.A. Jr.

1988-01-01

This paper presents groundwater monitoring strategies at the Weldon Spring Site in east-central Missouri. The Weldon Spring Site is former ordnance works and uranium processing facility. In 1987, elevated levels of inorganic anions and nitroaromatics were detected in groundwater beneath the site. Studies are currently underway to characterize the hydrogeologic regime and to define groundwater contamination. The complex hydrogeology at the Weldon Spring Site requires innovative monitoring strategies. Combinations of fracture and conduit flow exist in the limestone bedrock. Perched zones are also present near surface impoundments. Losing streams and springs surround the site. Confronting this complex combination of hydrogeologic conditions is especially challenging

Ground water monitoring strategies at the Weldon Spring Site, Weldon Spring, Missouri

International Nuclear Information System (INIS)

Meyer, K.A. Jr.

1988-01-01

This paper presents ground water monitoring strategies at the Weldon Spring Site in east-central Missouri. The Weldon Spring Site is a former ordnance works and uranium processing facility. In 1987, elevated levels of inorganic anions and nitroaromatics were detected in ground water beneath the site. Studies are currently underway to characterize the hydrogeologic regime and to define ground water contamination. The complex hydrogeology at the Weldon Spring Site requires innovative monitoring strategies. Combinations of fracture and conduit flow exist in the limestone bedrock. Perched zones are also present near surface impoundments. Losing streams and springs surround the site. Solving this complex combination of hydrogeologic conditions is especially challenging

Identifying sources of groundwater pollution using trace element signatures

International Nuclear Information System (INIS)

Olmez, I.; Hayes, M.J.

1990-01-01

A simple receptor modeling approach has been applied to groundwater pollution studies and has shown that marker trace elements can be used effectively in source identification and apportionment. Groundwater and source materials from one coal-fired and five oil-fired power plants, and one coal-tar deposit site have been analyzed by instrumental neutron activation analysis for more than 20 minor and trace elements. In one of the oil-fired power plants, trace element patterns indicated a leak from the hazardous waste surface impoundments owing to the failure of a hypolon liner. Also, the extent and spatial distribution of groundwater contamination have been determined in a coal-tar deposit site

Experimental study of surface plasmon-phonon polaritons in GaAs-based microstructures

Science.gov (United States)

Galimov, A. I.; Shalygin, V. A.; Moldavskaya, M. D.; Panevin, V. Yu; Melentyev, G. A.; Artemyev, A. A.; Firsov, D. A.; Vorobjev, L. E.; Klimko, G. V.; Usikova, A. A.; Komissarova, T. A.; Sedova, I. V.; Ivanov, S. V.

2018-03-01

Optical properties of a heavily-doped GaAs epitaxial layer with a regular grating at its surface have been experimentally investigated in the terahertz spectral range. Reflectivity spectra for the layer with a profiled surface drastically differ from those for the as-grown epilayer with a planar surface. For s-polarized radiation, this difference is totally caused by the electromagnetic wave diffraction at the grating. For p-polarized radiation, additional resonant dips arise due to excitation of surface plasmon-phonon polaritons. Terahertz radiation emission under significant electron heating in an applied pulsed electric field has also been studied. Polarization measurements revealed pronounced peaks related to surface plasmon-phonon polariton resonances of the first and second order in the emission spectra.

Electron microscopy study of the microstructure of Ni–W substrate surface

Energy Technology Data Exchange (ETDEWEB)

Ovcharov, A. V.; Karateev, I. A.; Mikhutkin, A. A. [National Research Centre “Kurchatov Institute,” (Russian Federation); Orekhov, A. S. [Russian Academy of Sciences, Shubnikov Institute of Crystallography, Federal Scientific Research Centre “Crystallography and Photonics,” (Russian Federation); Presniakov, M. Yu.; Chernykh, I. A.; Zanaveskin, M. L.; Kovalchuk, M. V.; Vasiliev, A. L., E-mail: a.vasiliev56@gmail.com [National Research Centre “Kurchatov Institute,” (Russian Federation)

2016-11-15

The surface microstructure of Ni–W alloy tapes, which are used as substrates to form films of high-temperature superconductors and photovoltaic devices, has been studied. Several samples of a Ni{sub 95}W{sub 5} tape (Evico) annealed under different conditions were analyzed using scanning electron microscopy, energy-dispersive X-ray microanalysis, electron diffraction, and electron energy-loss spectroscopy. NiWO{sub 4} precipitates are found on the surface of annealed samples. The growth of precipitates at a temperature of 950°C is accompanied by the formation of pores on the surface or under an oxide film. Depressions with a wedge-shaped profile are found at the grain boundaries. Annealing in a reducing atmosphere using a specially prepared chamber allows one to form a surface free of nickel tungstate precipitates.

Pectin nanocoating of titanium implant surfaces - an experimental study in rabbits

DEFF Research Database (Denmark)

Gurzawska, Katarzyna Aleksandra; Dirscherl, Kai; Jørgensen, Bodil

2017-01-01

that may increase adhesion of bone proteins, and bone cells at the implant surface. Nanocoating with pectins, plant cell wall-derived polysaccharides, is frequently done using rhamnogalacturonan-I (RG-I). AIM: The aim of the study was to evaluate the effect of nanocoating titanium implants with plant cell...... wall-derived rhamnogalacturonan-I, on bone healing and osseointegration. MATERIAL AND METHODS: Machined titanium implants were coated with three modifications of rhamnogalacturonan-I (RG-I). Chemical and physical surface properties were examined before insertion of nanocoated implants (n = 96....... The bone response to the nanocoated implants was analyzed qualitatively and quantitatively after 2, 4, 6, and 8 weeks of healing using light microscopy and histomorphometric methods. RESULTS: The RG-I coating influenced the surface chemical composition; wettability and roughness, making the surface more...

Observational study of surface wind along a sloping surface over mountainous terrain during winter

Science.gov (United States)

Lee, Young-Hee; Lee, Gyuwon; Joo, Sangwon; Ahn, Kwang-Deuk

2018-03-01

The 2018 Winter Olympic and Paralympic Games will be held in Pyeongchang, Korea, during February and March. We examined the near surface winds and wind gusts along the sloping surface at two outdoor venues in Pyeongchang during February and March using surface wind data. The outdoor venues are located in a complex, mountainous terrain, and hence the near-surface winds form intricate patterns due to the interplay between large-scale and locally forced winds. During February and March, the dominant wind at the ridge level is westerly; however, a significant wind direction change is observed along the sloping surface at the venues. The winds on the sloping surface are also influenced by thermal forcing, showing increased upslope flow during daytime. When neutral air flows over the hill, the windward and leeward flows show a significantly different behavior. A higher correlation of the wind speed between upper- and lower-level stations is shown in the windward region compared with the leeward region. The strong synoptic wind, small width of the ridge, and steep leeward ridge slope angle provide favorable conditions for flow separation at the leeward foot of the ridge. The gust factor increases with decreasing surface elevation and is larger during daytime than nighttime. A significantly large gust factor is also observed in the leeward region.

Overland erosion of uranium-mill-tailings impoundments: physical processes and computational methods

International Nuclear Information System (INIS)

Walters, M.H.

1983-03-01

The surface runoff and erosional processes of watersheds caused by rainfall-runoff are reviewed. Soil properties, topography, and rainstorm distribution are discussed with respect to their effects on soil erosion. The effects of climate and vegetation are briefly presented. Regression models and physical process simulation models are reviewed

Theoretical study of n-alkane adsorption on metal surfaces

DEFF Research Database (Denmark)

Morikawa, Yoshitada; Ishii, Hisao; Seki, Kazuhiko

2004-01-01

The interaction between n-alkane and metal surfaces has been studied by means of density-functional theoretical calculations within a generalized gradient approximation (GGA). We demonstrate that although the GGA cannot reproduce the physisorption energy well, our calculations can reproduce the e...

NMR characterization of hydrocarbon adsorption on calcite surfaces: A first principles study

Energy Technology Data Exchange (ETDEWEB)

Bevilaqua, Rochele C. A.; Miranda, Caetano R. [Centro de Ciências Naturais e Humanas, Universidade Federal do ABC, UFABC, Santo André, SP (Brazil); Rigo, Vagner A. [Centro de Ciências Naturais e Humanas, Universidade Federal do ABC, UFABC, Santo André, SP (Brazil); Universidade Tecnológica Federal do Paraná, UTFPR, Cornélio Procópio, PR (Brazil); Veríssimo-Alves, Marcos [Centro de Ciências Naturais e Humanas, Universidade Federal do ABC, UFABC, Santo André, SP (Brazil); Departamento de Física, ICEx, Universidade Federal Fluminense, UFF, Volta Redonda, RJ (Brazil)

2014-11-28

The electronic and coordination environment of minerals surfaces, as calcite, are very difficult to characterize experimentally. This is mainly due to the fact that there are relatively few spectroscopic techniques able to detect Ca{sup 2+}. Since calcite is a major constituent of sedimentary rocks in oil reservoir, a more detailed characterization of the interaction between hydrocarbon molecules and mineral surfaces is highly desirable. Here we perform a first principles study on the adsorption of hydrocarbon molecules on calcite surface (CaCO{sub 3} (101{sup ¯}4)). The simulations were based on Density Functional Theory with Solid State Nuclear Magnetic Resonance (SS-NMR) calculations. The Gauge-Including Projector Augmented Wave method was used to compute mainly SS-NMR parameters for {sup 43}Ca, {sup 13}C, and {sup 17}O in calcite surface. It was possible to assign the peaks in the theoretical NMR spectra for all structures studied. Besides showing different chemical shifts for atoms located on different environments (bulk and surface) for calcite, the results also display changes on the chemical shift, mainly for Ca sites, when the hydrocarbon molecules are present. Even though the interaction of the benzene molecule with the calcite surface is weak, there is a clearly distinguishable displacement of the signal of the Ca sites over which the hydrocarbon molecule is located. A similar effect is also observed for hexane adsorption. Through NMR spectroscopy, we show that aromatic and alkane hydrocarbon molecules adsorbed on carbonate surfaces can be differentiated.

Studies of drag on the nanocomposite superhydrophobic surfaces

Energy Technology Data Exchange (ETDEWEB)

Brassard, Jean-Denis [Anti-icing Materials International Laboratory (AMIL), Université du Québec à Chicoutimi, 555 Boulevard de l‘Université, Chicoutimi, Québec, Canada G7H 2B1 (Canada); Centre Universitaire de Recherche sur l’Aluminium (CURAL), Université du Québec à Chicoutimi, 555 Boulevard de l‘Université, Chicoutimi, Québec, Canada G7H 2B1 (Canada); Sarkar, D.K., E-mail: dsarkar@uqac.ca [Centre Universitaire de Recherche sur l’Aluminium (CURAL), Université du Québec à Chicoutimi, 555 Boulevard de l‘Université, Chicoutimi, Québec, Canada G7H 2B1 (Canada); Perron, Jean [Anti-icing Materials International Laboratory (AMIL), Université du Québec à Chicoutimi, 555 Boulevard de l‘Université, Chicoutimi, Québec, Canada G7H 2B1 (Canada)

2015-01-01

Graphical abstract: - Highlights: • The nanocomposite thin films of stearic acid (SA)-functionalized ZnO nanoparticles incorporated in epoxy polymer matrix have been achieved. • SA-functionalization of ZnO nanoparticles in the thin films was confirmed by XRD and FTIR. • The measured rms roughness of the thin film is found to be 12 ± 1 μm with the adhesion of 5B on glass. • The wetting property shows that the surface of the film is superhydrophobic with the CA of 156 ± 4° and CAH of 4 ± 2°. • The drag reduction on the surface of superhydrophobic glass sphere is 16% lower than as-received glass sphere. - Abstract: The nanocomposite thin films of stearic acid (SA)-functionalized ZnO nanoparticles incorporated in epoxy polymer matrix have been achieved. The X-ray diffraction (XRD) studies show the formation of zinc stearate on ZnO nanoparticles as the confirmation of SA-functionalization of ZnO nanoparticles in the thin films. Morphological analyses reveal the presence of micro-holes with the presence of irregular nanoparticles. The measured root mean square (rms) roughness of the thin film is found to be 12 ± 1 μm with the adhesion of 5B on both glass and aluminum substrates. The wetting property shows that the surface of the film is superhydrophobic with the contact angle of water of 156 ± 4° having contact angle hysteresis (CAH) of 4 ± 2°. The average terminal velocity in the water of the as-received glass spheres and superhydrophobic spheres were found to be 0.66 ± 0.01 m/s and 0.72 ± 0.01 m/s respectively. Consequently, the calculated average coefficients of the surface drag of the as-received glass sphere and superhydrophobic glass sphere were 2.30 ± 0.01 and 1.93 ± 0.03, respectively. Hence, the drag reduction on the surface of superhydrophobic glass sphere is found to be approximately 16% lower than as-received glass sphere.

Studies of drag on the nanocomposite superhydrophobic surfaces

International Nuclear Information System (INIS)

Brassard, Jean-Denis; Sarkar, D.K.; Perron, Jean

2015-01-01

Graphical abstract: - Highlights: • The nanocomposite thin films of stearic acid (SA)-functionalized ZnO nanoparticles incorporated in epoxy polymer matrix have been achieved. • SA-functionalization of ZnO nanoparticles in the thin films was confirmed by XRD and FTIR. • The measured rms roughness of the thin film is found to be 12 ± 1 μm with the adhesion of 5B on glass. • The wetting property shows that the surface of the film is superhydrophobic with the CA of 156 ± 4° and CAH of 4 ± 2°. • The drag reduction on the surface of superhydrophobic glass sphere is 16% lower than as-received glass sphere. - Abstract: The nanocomposite thin films of stearic acid (SA)-functionalized ZnO nanoparticles incorporated in epoxy polymer matrix have been achieved. The X-ray diffraction (XRD) studies show the formation of zinc stearate on ZnO nanoparticles as the confirmation of SA-functionalization of ZnO nanoparticles in the thin films. Morphological analyses reveal the presence of micro-holes with the presence of irregular nanoparticles. The measured root mean square (rms) roughness of the thin film is found to be 12 ± 1 μm with the adhesion of 5B on both glass and aluminum substrates. The wetting property shows that the surface of the film is superhydrophobic with the contact angle of water of 156 ± 4° having contact angle hysteresis (CAH) of 4 ± 2°. The average terminal velocity in the water of the as-received glass spheres and superhydrophobic spheres were found to be 0.66 ± 0.01 m/s and 0.72 ± 0.01 m/s respectively. Consequently, the calculated average coefficients of the surface drag of the as-received glass sphere and superhydrophobic glass sphere were 2.30 ± 0.01 and 1.93 ± 0.03, respectively. Hence, the drag reduction on the surface of superhydrophobic glass sphere is found to be approximately 16% lower than as-received glass sphere

Nanostructured surfaces investigated by quantitative morphological studies

International Nuclear Information System (INIS)

Perani, Martina; Carapezzi, Stefania; Mutta, Geeta Rani; Cavalcoli, Daniela

2016-01-01

The morphology of different surfaces has been investigated by atomic force microscopy and quantitatively analyzed in this paper. Two different tools have been employed to this scope: the analysis of the height–height correlation function and the determination of the mean grain size, which have been combined to obtain a complete characterization of the surfaces. Different materials have been analyzed: SiO_xN_y, InGaN/GaN quantum wells and Si nanowires, grown with different techniques. Notwithstanding the presence of grain-like structures on all the samples analyzed, they present very diverse surface design, underlying that this procedure can be of general use. Our results show that the quantitative analysis of nanostructured surfaces allows us to obtain interesting information, such as grain clustering, from the comparison of the lateral correlation length and the grain size. (paper)

Environmental systems and management activities on the Kennedy Space Center, Merritt Island, Florida: results of a modeling workshop

Science.gov (United States)

Hamilton, David B.; Andrews, Austin K.; Auble, Gregor T.; Ellison, Richard A.; Farmer, Adrian H.; Roelle, James E.

1985-01-01

from a number of disciplines and agencies. This integration occurred in the computer simulation model and among workshop participants as submodel linkages were developed and scenario results discussed. A number of research needs were identified at the workshop during the model building and testing exercises and associated discussions. These needs were based on the informed judgement of researchers and managers familiar with Merritt Island or similar areas, rather than on a comprehensive literature review of sensitivity analysis of the preliminary model developed at the workshop. Some of the needs can be addressed by interpreting the results of completed studies from similar geographic areas as they relate to Merritt Island, while other will require additional research studies on Merritt Island. Major research needs associated with the Upland submodel include behavior of the near-surface aquifer, factors limiting slash pine regeneration, frequency and effects of natural fire on various cover types, cumulative effects of shuttle launches, and fate in upland soils of nitrogen and phosphorous from land applied waste material. Key Impoundment submodel needs include documentation of vegetation changes in response to altered water depth, salinity, and nutrient concentrations and better specification of the functional characteristics of impoundments as chemical filters. Important information gaps identified in the Estuary submodel include a more complete analysis of factors contributing to phytoplankton abundance, evaluation of sources of turbidity other than phytoplankton, and identification and quantification of factors limiting seagrass distribution. Primary research needs associated with the Wildlife submodel include a survey of breeding habitat, production data, and harvest data for mottled ducks; data on the emigration and immigration of juvenile mullet (and other transient fish) in the impoundment; the contribution of various seagrasses to habitat requirements of sea