WorldWideScience

Sample records for surface contamination levels

  1. Automatic Measurement of Low Level Contamination on Concrete Surfaces

    International Nuclear Information System (INIS)

    Tachibana, M.; Itoh, H.; Shimada, T.; Yanagihara, S.

    2002-01-01

    Automatic measurement of radioactivity is necessary for considering cost effectiveness in final radiological survey of building structures in decommissioning nuclear facilities. The RAPID (radiation measuring pilot device for surface contamination) was developed to be applied to automatic measurement of low level contamination on concrete surfaces. The RAPID has a capability to measure contamination with detection limit of 0.14 Bq/cm2 for 60Co in 30 seconds of measurement time and its efficiency is evaluated to be 5 m2/h in a normal measurement option. It was confirmed that low level contamination on concrete surfaces could be surveyed by the RAPID efficiently compared with direct measurement by workers through its actual application

  2. Experimental study on source efficiencies for estimating surface contamination level

    International Nuclear Information System (INIS)

    Ichiji, Takeshi; Ogino, Haruyuki

    2008-01-01

    Source efficiency was measured experimentally for various materials, such as metals, nonmetals, flooring materials, sheet materials and other materials, contaminated by alpha and beta emitter radioactive nuclides. Five nuclides, 147 Pm, 60 Co, 137 Cs, 204 Tl and 90 Sr- 90 Y, were used as the beta emitters, and one nuclide 241 Am was used as the alpha emitter. The test samples were prepared by placing drops of the radioactive standardized solutions uniformly on the various materials using an automatic quantitative dispenser system from Musashi Engineering, Inc. After placing drops of the radioactive standardized solutions, the test materials were allowed to dry for more than 12 hours in a draft chamber with a hood. The radioactivity of each test material was about 30 Bq. Beta rays or alpha rays from the test materials were measured with a 2-pi gas flow proportional counter from Aloka Co., Ltd. The source efficiencies of the metals, nonmetals and sheet materials were higher than 0.5 in the case of contamination by the 137 Cs, 204 Tl and 90 Sr- 90 Y radioactive standardized solutions, higher than 0.4 in the case of contamination by the 60 Co radioactive standardized solution, and higher than 0.25 in the case of contamination by the alpha emitter the 241 Am radioactive standardized solution. These values were higher than those given in Japanese Industrial Standards (JIS) documents. In contrast, the source efficiencies of some permeable materials were lower than those given in JIS documents, because source efficiency varies depending on whether the materials or radioactive sources are wet or dry. This study provides basic data on source efficiency, which is useful for estimating the surface contamination level of materials. (author)

  3. Assessment of surface contamination level in an operating uranium ore processing facility of Jaduguda, India

    International Nuclear Information System (INIS)

    Meena, J.S.; Patnaik, R.L.; Jha, V.N.; Sahoo, S.K.; Ravi, P.M.; Tripathi, R.M.

    2014-01-01

    Radiological concern of the occupational workers and the area is given priority over other safety issue in confirmation with the stipulated guideline of national regulatory agency (AERB/FEFCF/SG-2, 2007). The key concern from the radiological hazard evaluation point of view is air activity, external gamma level and surface contamination. Present investigations was carried out to ascertain the surface contamination level of uranium ore processing facility at Jaduguda, Jharkhand. For a low grade uranium ore processing industry surface contamination is a major concern in product precipitation and recovery section. In view of this, the ore processing plant can broadly be classified into three areas i.e. ion exchange area, precipitation and product recovery section and other areas. The monitoring results incorporate the level of surface contamination of the plant during the last five years. The geometric mean activity of surface contamination level was 31.1, 34.5 and 9.8 Bq dm -2 in ion exchange, product precipitation and recovery and other areas with GSD of 2, 2.5 and 1.9. In most of the cases the surface contamination level was well within the recommended limit of 100 Bq dm -2 for M class uranium compound. Occasional cases of surface contamination levels exceeding the recommended limit were addressed and areas were decontaminated. Based on the study, modification in the design feature of the surface of the finished product section was also suggested so that the decontamination procedure can be more effectively implemented

  4. Surface tritium contamination studies

    International Nuclear Information System (INIS)

    Sienkiewicz, C.J.

    1986-01-01

    Glovebox wipe surveys were conducted to correlate surface tritium contamination with atmospheric tritium levels. Surface contamination was examined as a function of tritium concentration and limited to the HT/T 2 form. The previously predicted relationship between atmospheric HTO concentration and cleanup times was examined in order to predict a model for atmospheric detritiation of stainless steel enclosures. 2 figures, 2 tables

  5. Contamination problems from glass beaker inner surface in low level Po-210 analysis

    Czech Academy of Sciences Publication Activity Database

    Kameník, Jan; Hölgye, Z.

    2010-01-01

    Roč. 283, č. 2 (2010), s. 493-495 ISSN 0236-5731 Institutional research plan: CEZ:AV0Z10480505 Keywords : Po-210 * Low-level analysis * Contamination Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 0.777, year: 2010

  6. Body Surface Contamination Levels of Residents under Different Evacuation Scenarios after the Fukushima Daiichi Nuclear Power Plant Accident.

    Science.gov (United States)

    Ohba, Takashi; Hasegawa, Arifumi; Kohayagawa, Yoshitaka; Kondo, Hisayoshi; Suzuki, Gen

    2017-09-01

    Body surface contamination levels should be correlated with inhaled actual thyroid doses during evacuation following the Fukushima Daiichi nuclear power plant (FDNPP) accident. Evacuees and residents were screened for body surface contamination using a Geiger-Mueller survey meter. The authors obtained 7,539 individual screening data sheets as well as gamma-spectrometry data from measurements made on clothing of two subjects by using a germanium spectrometer. Body surface contamination levels were analyzed in four residential groups during two different periods: 12-14 and 15-17 March 2011. Contamination levels during 12-14 March in the Tomioka/Okuma/Futaba/Naraha group were very low, indicating that residents evacuated before the radioactive plume reached their towns on 12 March. In contrast, levels in the Namie and Minamisoma groups were higher than those in the other groups in both periods, indicating that these residents were exposed to plumes twice on 12 and 15-16 March. The plume on 12 March was enriched with short-lived radionuclides: averaged proportions of radioactivity (relative to I) from Te, I, and Cs measured in clothing from two subjects were 2.3, 1.1, and 0.1, respectively, after correction for physical decay by 12:00 on 12 March. These proportions are similar to those (relative to I) from Te and Cs in dust sampled by a high-volume air sampler in the zone 20 km from the FDNPP on 12 March: 1.9 and 0.1, respectively. These data indicate that the relative contribution to inhaled thyroid dose of short-lived radionuclides in radioactive plumes released on 12 March could be as much as 37.5% in 1-y-old children.

  7. Contaminant mass estimation of powder contaminated surfaces

    Science.gov (United States)

    Gibbs, Timothy J.; Messinger, David W.

    2017-05-01

    How can we determine the physical characteristics of a mixture of multiple materials within a single pixel? Intimate mixing occurs when different materials within the region encompassed by a pixel interact with each other prior to reaching the sensor. For powder contaminated surfaces, nonlinear mixing is unavoidable. The Nonconventional Exploitation Factors Data System (NEFDS) Contamination Model can make longwave hyperspectral mixture signatures, but only for a small subset of their spectral library. In addition, the model uses percent coverage as its only physical property input despite it not being informative to the contaminants physical properties. Through a complex parameter inversion, the NEFDS contamination model can be used to derive various physical properties. These physical characteristics were estimated by using empirically measured data of varying contaminant amounts using a Designs and Prototypes Fourier transform infrared spectrometer. Once estimated parameters are found, the mixture spectra was recreated and compared to the measured data. The estimated areal coverage density is used to derive a total deposited mass on the surface based on the area of contaminated surface. This is compared to the known amount deposited that was measured during the experimental campaign. This paper presents some results of those measurements and model estimates.

  8. Contamination levels of human pharmaceutical compounds in French surface and drinking water.

    Science.gov (United States)

    Mompelat, S; Thomas, O; Le Bot, B

    2011-10-01

    The occurrence of 20 human pharmaceutical compounds and metabolites from 10 representative therapeutic classes was analysed from resource and drinking water in two catchment basins located in north-west France. 98 samples were analysed from 63 stations (surface water and drinking water produced from surface water). Of the 20 human pharmaceutical compounds selected, 16 were quantified in both the surface water and drinking water, with 22% of the values above the limit of quantification for surface water and 14% for drinking water). Psychostimulants, non-steroidal anti-inflammatory drugs, iodinated contrast media and anxiolytic drugs were the main therapeutic classes of human pharmaceutical compounds detected in the surface water and drinking water. The results for surface water were close to results from previous studies in spite of differences in prescription rates of human pharmaceutical compounds in different countries. The removal rate of human pharmaceutical compounds at 11 water treatment units was also determined. Only caffeine proved to be resistant to drinking water treatment processes (with a minimum rate of 5%). Other human pharmaceutical compounds seemed to be removed more efficiently (average elimination rate of over 50%) by adsorption onto activated carbon and oxidation/disinfection with ozone or chlorine (not taking account of the disinfection by-products). These results add to the increasing evidence of the occurrence of human pharmaceutical compounds in drinking water that may represent a threat to human beings exposed to a cocktail of human pharmaceutical compounds and related metabolites and by-products in drinking water.

  9. Instruments Sniff Organic Surface Contaminants

    Science.gov (United States)

    Adler-Golden, Steven; Matthew, Michael W.

    1995-01-01

    Portable instruments detecting both nonvolatile and volatile organic surface contaminants in real time developed. Instruments easy to use: operate under ordinary ambient atmospheric conditions, without need to use messy liquid solvents or install and remove witness plates, and without need to cut specimens from surfaces to be inspected. Principle of detection involves sweeping pure, activated gas across surface spot inspected, then monitoring light emitted at wavelengths characteristic of excited molecules formed by chemical reactions between activated gas and contaminants. Gas activated by dc discharge, radio-frequency induction, microwave radiation, laser beam, hot filaments, or any other suitable means that excites some of gas molecules.

  10. Derived limits for surface contamination

    CERN Document Server

    Wrixon, A D; Linsley, G S; White, D F

    1979-01-01

    Derived limits (DLs) for surface contamination were first established for use in the nuclear energy industry where a wide variety of radionuclides is encountered. They were later used in factories, hospitals, and universities, where the radionuclides used are normally fewer in number, either known or readily identifiable, and often of low toxicity. In these situations the current limits are frequently over-restrictive. This report describes a reassessment of the values in the light of more recent information on the possible pathways of exposure and the dose equivalent limits given in ICRP Publication 26. The reassessment is prompted also by the introduction of SI units. The results of the reassessment are used to produce a classification of DLs for all radionuclides for active and inactive area surfaces and for skin.

  11. Hard-surface contamination detection exercise

    Energy Technology Data Exchange (ETDEWEB)

    Kawa, S.

    1991-12-31

    The purpose of this thesis is to create a practical exercise which demonstrates the techniques used by Health Physicists to detect surface contamination, including both instrumentation and smear survey techniques. By understanding the basic principles of the most commonly found instruments the intent is that a new Health Physics graduate can correctly choose, and apply an instrument to their detection situation. The exercise is also intended to acquaint students with the very basic principles of smear techniques. Smear surveys are probably the most universally applied technique in this industry, however, very little literature exists on the subject. The techniques are usually taught, on-the-job and by demonstration. By their seeing and participating in this presentation, it is intended that Health Physics students can accelerate their first few weeks at their new careers, and enable them to recognize common mistakes. Health Physicists are expected to have knowledge of the basic practices of their profession. This exercise will allow Health Physics students to become familiar with the use of hand-held detection devices and the technique of smear surveys. Adequate measurement and recording of surface contamination information is necessary to: meet licensing requirements; protect the health and safety of the workers; maintain accurate records in the case of litigation or dose reconstruction; and maintain high levels of professional competency. This exercise will assist students in obtaining the skills necessary to adequately measure and record levels of surface contamination. 41 refs., 14 figs., 2 tabs.

  12. Evaluation of Unfixed Tritium Surface Contamination

    International Nuclear Information System (INIS)

    Postolache, C.; Matei, Lidia

    2005-01-01

    Surface unfixed radioactive contamination represents the amount of surface total radioactive contamination which can be eliminated by pure mechanical processes. This unfixed contamination represents the main risk factor for contamination of the personnel which operates in tritium laboratories. Unfixed contamination was determined using sampling smears type FPCSN-PSE-AA. Those FPCSN-PSE-AA smears are disks of expanded polystyrene which contain acrylic acid fragments superficially grafted. Sampling factor was determinated by contaminated surface wiping with moisten smears in 50 μL butylic alcohol and activity measuring at liquid scintillation measuring device. Sampling factor was determined by the ratio between measured activity and initially real conventional activity. The sampling factor was determined for Tritium Laboratory existent surfaces: stainless steel, aluminum, glass, ceramics, linoleum, washable coats, epoxy resins type ALOREX LP-52.The sampling factors and the reproducibility were determined in function of surface nature

  13. Removing high-level contaminants

    International Nuclear Information System (INIS)

    Wallace, Paula

    2013-01-01

    Full text: Using biomimicry, an Australian cleantech innovation making inroads intoChinas's industrial sector offers multiple benefits to miners and processors in Australia. Stephen Shelley, the executive chairman of Creative Water Technology (CWT), was on hand at a recent trade show to explain how his Melbourne company has developed world-class techniques in zero liquid discharge and fractional crystallization of minerals to apply to a wide range of water treatment and recycling applications. “Most existing technologies operate with high energy distillation, filters or biological processing. CWT's appliance uses a low temperature, thermal distillation process known as adiabatic recovery to desalinate, dewater and/or recycle highly saline and highly contaminated waste water,” said Shelley. The technology has been specifically designed to handle the high levels of contaminant that alternative technologies struggle to process, with proven water quality results for feed water samples with TDS levels over 300,000ppm converted to clean water with less than 20ppm. Comparatively, reverse osmosis struggles to process contaminant levels over 70,000ppm effectively. “CWT is able to reclaim up to 97% clean usable water and up to 100% of the contaminants contained in the feed water,” said Shelley, adding that soluble and insoluble contaminants are separately extracted and dried for sale or re-use. In industrial applications CWT has successfully processed feed water with contaminant levels over 650,000 mg/1- without the use of chemicals. “The technology would be suitable for companies in oil exploration and production, mining, smelting, biofuels, textiles and the agricultural and food production sectors,” said Shelley. When compared to a conventional desalination plant, the CWT system is able to capture the value in the brine that most plants discard, not only from the salt but the additional water it contains. “If you recover those two commodities

  14. Drivers of contaminant levels in surface water of China during 2000-2030: Relative importance for illustrative home and personal care product chemicals.

    Science.gov (United States)

    Zhu, Ying; Price, Oliver R; Kilgallon, John; Qi, Yi; Tao, Shu; Jones, Kevin C; Sweetman, Andrew J

    2018-03-21

    Water pollution are among the most critical problems in China and emerging contaminants in surface water have attracted rising attentions in recent years. There is great interest in China's future environmental quality as the national government has committed to a major action plan to improve surface water quality. This study presents methodologies to rank the importance of socioeconomic and environmental drivers to the chemical concentration in surface water during 2000-2030. A case study is conducted on triclosan, a home and personal care product (HPCP) ingredient. Different economic and discharge flow scenarios are considered. Urbanization and wastewater treatment connection rates in rural and urban areas are collected or projected for 2000-2030 for counties across China. The estimated usage increases from ca. 86 to 340 t. However, emissions decreases from 76 to 52 t during 2000-2030 under a modelled Organisation for Economic Co-operation (OECD) economic scenario because of the urbanization, migration and development of wastewater treatment plants/facilities (WWTPs). The estimated national median concentration of triclosan ranges 1.5-8.2 ng/L during 2000-2030 for different scenarios. It peaks in 2009 under the OECD and three of the Intergovernmental Panel on Climate Change (IPCC), A2, B1 and B2 economic scenarios, but in 2025 under A1 economic scenario. Population distribution and surface water discharge flow rates are ranked as the top two drivers to triclosan levels in surface water over the 30 years. The development of urban WWTPs was the most important driver during 2000-2010 and the development of rural works is projected to be the most important in 2011-2030. Projections suggest discharges of ingredients in HPCPs - controlled by economic growth - should be balanced by the major expenditure programme on wastewater treatment in China. Copyright © 2018 Elsevier Ltd. All rights reserved.

  15. Techniques for removing contaminated concrete surfaces

    International Nuclear Information System (INIS)

    Halter, J.M.; Sullivan, R.G.

    1981-01-01

    This discussion compares various techniques that have been used to clean concrete surfaces by removing the surface. Three techniques which have been investigated by the Pacific Northwest Laboratory for removing surfaces are also described: the water cannon, the concrete spaller, and high-pressure water jet. The equipment was developed with the assumption that removal of the top 1/8 to 1/4 in. of surface would remove most of the contamination. If the contamination has gone into cracks or deep voids in the surface, the removal processes can be repeated until the surface is acceptable

  16. Residual viral and bacterial contamination of surfaces after cleaning and disinfection

    NARCIS (Netherlands)

    Tuladhar, E.; Hazeleger, W.C.; Koopmans, M.; Zwietering, M.H.; Beumer, R.R.; Duizer, E.

    2012-01-01

    Environmental surfaces contaminated with pathogens can be sources of indirect transmission, and cleaning and disinfection are common interventions focused on reducing contamination levels. We determined the efficacy of cleaning and disinfection procedures for reducing contamination by noroviruses,

  17. Abnormal ''Contamination' Levels On Garden Appliances

    International Nuclear Information System (INIS)

    German, U.; Levinson, S.; Elmelech, V.; Pelled, O.; Tshuva, A.; Laichter, Y.

    1999-01-01

    During routine contamination checks we encountered an abnormal high level of Alpha and Beta emitting radioisotopes on working gloves of employees of the gardening department. It came out that the source was due to ''contamination'' levels on steering wheels of some gardening machines. In order to ensure that no real contamination of these workers was involved , a series of checks was started to identity the source of the abnormal levels found during monitoring

  18. Calibration of alpha surface contamination monitor

    International Nuclear Information System (INIS)

    Freitas, I.S.M. de; Goncalez, O.L.

    1990-01-01

    In this work, the results, as well as the methodology, of the calibration of an alpha surface contamination monitor are presented. The calibration factors are obtained by least-squares fitting with effective variance. (author)

  19. Monitoring of surface and airborne contamination

    Energy Technology Data Exchange (ETDEWEB)

    Pradeep Kumar, K.S. [Bhabha Atomic Research Centre, Bombay (India)

    1997-06-01

    Indian nuclear energy programme aims at total safety in all activities involved in the entire fuel cycle for the occupational workers, members of the public and the environment as a whole. Routine radiation monitoring with clearly laid out procedures are followed for ensuring the safety of workers and public. Radiation monitoring carried out for the nuclear installations comprises of process monitoring, monitoring of effluent releases and also of the radiation protection monitoring of the individuals, work place and environment. Regulations like banning of smoking and consumption of food and drink etc. reduces the risk of direct ingestion even if inadvertent spread of contamination takes place. Though limit of transportable surface contamination is prescribed, the health physicists always follow a ``clean on swipe`` philosophy which compensates any error in the measurement of surface contamination. In this paper, the following items are contained: Necessity of contamination monitoring, accuracy required in the calibration of surface contamination monitors, methodology for contamination monitoring, air monitoring, guidelines for unrestricted release of scrap materials, and problems in contamination monitoring. (G.K.)

  20. Development of radioactive surface contamination monitor

    International Nuclear Information System (INIS)

    Hashimoto, Tadao; Hasegawa, Toru; Fukumoto, Keisuke; Ooki, Yasushi

    2008-01-01

    In the radiation facilities such as nuclear power plants, surface contamination of the people accessing or articles conveyed in and out of the radiation controlled areas is detected and monitored by installing contamination monitors at the boundary of controlled areas and uncontrolled areas against the expansion of the radioactive materials to out of the facilities. It is required for the surface contamination of articles to be tightened of control criteria as 'Guidelines for discrimination ways of nonradioactive waste (not classified as radioactive waste) generated from nuclear power plants' (hereinafter referred to as 'the Guideline') was established by the Nuclear and Industrial Safety Agency of the Ministry of Economy, Trade and Industry in August, 2005. It predicts that the control criteria of monitors other than article monitors are also tightened in the future. Fuji electric has been fabricating and delivering surface contamination detecting monitors. Now we are developing the new contamination monitor corresponding to the tightening of the control criteria. 'Large article transfer monitor', 'Clothing monitor' and 'Body surface contamination monitor' are introduced in this article. (author)

  1. Occurrence of Surface Water Contaminations: An Overview

    Science.gov (United States)

    Shahabudin, M. M.; Musa, S.

    2018-04-01

    Water is a part of our life and needed by all organisms. As time goes by, the needs by human increased transforming water quality into bad conditions. Surface water contaminated in various ways which is pointed sources and non-pointed sources. Pointed sources means the source are distinguished from the source such from drains or factory but the non-pointed always occurred in mixed of elements of pollutants. This paper is reviewing the occurrence of the contaminations with effects that occurred around us. Pollutant factors from natural or anthropology factors such nutrients, pathogens, and chemical elements contributed to contaminations. Most of the effects from contaminated surface water contributed to the public health effects also to the environments.

  2. Quantification of surface contamination: principles and applications

    International Nuclear Information System (INIS)

    Vo-Dinh, T.

    1982-01-01

    The applications discussed in this paper underscore the usefulness and versatility of molecular luminescence spectroscopy as an efficient surface detection technique. The technique can be used not only as a qualitative characterization method, but also as a quantitative analytical tool to detect trace contaminants on surfaces. Recent advances in instrumentation and methodology have expanded the applicability of surface luminescence into many new problem areas. Trace organics are emphasized here

  3. A consideration on internal dose evaluation and intervention based on a surface contamination concept

    International Nuclear Information System (INIS)

    Yasuda, H.

    1997-01-01

    Long-term radiation doses received by the inhabitants after the Chernobyl accident have been evaluated according to the surface contamination levels on the ground surface. The health effects have also been discussed by comparison between the surface-contaminated area and the uncontaminated control area. Selected protective measures were carried out in accordance with the contamination level of surface soil. These have been based on the 'surface contamination concept' which assumes that the radiation risk to inhabitants is proportional to the level of ground-surface contamination. The observations collected in regions around Chernobyl, however, show that the internal radiation doses to the inhabitants poorly correlate with the surface contamination level. This fact poses a question on the suitability of dose evaluations and interventions based on this concept

  4. Description of measurement techniques for surface contaminations

    International Nuclear Information System (INIS)

    Bourrez, E.

    2001-01-01

    The needs of evaluation of the surface contamination are numerous in the processes of production and management of radioactive waste. The market of radiation protection materials proposes a lot of devices answering to the almost all these needs. These device have however their conditions and particular limits for use. To realize correct measurements it is use the device, the technique and the methods adapted to the need, by taking into account the optimization of economical aspect. (N.C.)

  5. System for removing contaminated surface layers

    International Nuclear Information System (INIS)

    Yoshikawa, Kozo.

    1987-04-01

    The object of the present invention is to offer a new type of useful decontamination system, with which the contaminated surface layers can be removed effectively by injection of such solid microparticles. Liquid carbon dioxide is passed from a liquid carbon dioxide tank via the carbon dioxide supply line into the system for injecting solid carbon dioxide particles. Part of the liquid carbon dioxide introduced into the system is converted to solid carbon dioxide particles by the temperature drop resulting from adiabatic expansion in the carbon dioxide expansion space of the injection system. The solid carbon dioxide particles reach the injection nozzle, which is connected through the expansion space. The carbon dioxide microparticles are further cooled and accelerated by nitrogen gas injected from the nitrogen gas nozzle at the tip of the nitrogen gas supply line, which is connected to a liquid nitrogen tank. The cooled and accelerated solid carbon dioxide microparticles are injected from the injection nozzle for the solid carbon dioxide and directed against the contaminated surface to be cleaned, and, as a result, the surface contamination is removed

  6. 10 CFR Appendix D to Part 835 - Surface Contamination Values

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Surface Contamination Values D Appendix D to Part 835...—Surface Contamination Values The data presented in appendix D are to be used in identifying the need for posting of contamination and high contamination areas in accordance with § 835.603(e) and (f) and...

  7. Worker exposures from recycling surface contaminated radioactive scrap metal

    Energy Technology Data Exchange (ETDEWEB)

    Kluk, A. [Dept. of Energy, Germantown, MD (United States); Phillips, J.W.; Culp, J. [Analytical Services, Inc., Columbia, MD (United States)

    1996-12-31

    Current DOE policy permits release from DOE control of real property with residual levels of surficial radioactive contamination if the contamination is below approved guidelines. If the material contains contamination that is evenly distributed throughout its volume (referred to as volumetric contamination), then Departmental approval for release must be obtained in advance. Several DOE sites presently recycle surface contaminated metal, although the quantities are small relative to the quantities of metal processed by typical mini-mills, hence the potential radiation exposures to mill workers from processing DOE metals and the public from the processed metal are at present also a very small fraction of their potential value. The exposures calculated in this analysis are based on 100% of the scrap metal being processed at the maximum contamination levels and are therefore assumed to be maximum values and not likely to occur in actual practice. This paper examines the relationship between the surface contamination limits established under DOE Order 5400.5, {open_quotes}Radiation Protection of the Public and the Environment,{close_quotes} and radiation exposures to workers involved in the scrap metal recycling process. The analysis is limited to surficial contamination at or below the guideline levels established in DOE Order 5400.5 at the time of release. Workers involved in the melting and subsequent fabrication of products are not considered radiation workers (no requirements for monitoring) and must be considered members of the public. The majority of the exposures calculated in this analysis range from tenths of a millirem per year (mrem/yr) to less than 5 mrem/yr. The incremental risk of cancer associated with these exposures ranges from 10{sup -8} cancers per year to 10{sup -6} cancers per year.

  8. Worker exposures from recycling surface contaminated radioactive scrap metal

    International Nuclear Information System (INIS)

    Kluk, A.; Phillips, J.W.; Culp, J.

    1996-01-01

    Current DOE policy permits release from DOE control of real property with residual levels of surficial radioactive contamination if the contamination is below approved guidelines. If the material contains contamination that is evenly distributed throughout its volume (referred to as volumetric contamination), then Departmental approval for release must be obtained in advance. Several DOE sites presently recycle surface contaminated metal, although the quantities are small relative to the quantities of metal processed by typical mini-mills, hence the potential radiation exposures to mill workers from processing DOE metals and the public from the processed metal are at present also a very small fraction of their potential value. The exposures calculated in this analysis are based on 100% of the scrap metal being processed at the maximum contamination levels and are therefore assumed to be maximum values and not likely to occur in actual practice. This paper examines the relationship between the surface contamination limits established under DOE Order 5400.5, open-quotes Radiation Protection of the Public and the Environment,close quotes and radiation exposures to workers involved in the scrap metal recycling process. The analysis is limited to surficial contamination at or below the guideline levels established in DOE Order 5400.5 at the time of release. Workers involved in the melting and subsequent fabrication of products are not considered radiation workers (no requirements for monitoring) and must be considered members of the public. The majority of the exposures calculated in this analysis range from tenths of a millirem per year (mrem/yr) to less than 5 mrem/yr. The incremental risk of cancer associated with these exposures ranges from 10 -8 cancers per year to 10 -6 cancers per year

  9. Assessment of arsenic surface contamination in a museum anthropology department.

    Science.gov (United States)

    Gribovich, Andrey; Lacey, Steven; Franke, John; Hinkamp, David

    2013-02-01

    To assess potential arsenic (As) contamination of work surfaces to improve upon the control strategy at an anthropology department in a large natural history museum. Work practices were observed and control strategy reviewed to inform an occupational hygiene assessment strategy utilizing surface wipe sampling. A total of 35 sampling targets were identified, focusing on surfaces that receive high touch traffic, including workstations, artifact transport carts, and elevator buttons. Arsenic sampling and analysis were performed using reference method Occupational Safety and Health Administration ID-125G. Four of the sampling areas returned detectable levels of As, ranging from 0.052 to 0.350 μg/100 cm. Workplace observations and wipe sampling data enabled the development of recommendations to help to further reduce potential occupational exposure to As. Continuous reduction of surface contamination is prudent for known human carcinogens.

  10. Contamination detector for inner surface of container

    International Nuclear Information System (INIS)

    Watanabe, Tadao.

    1995-01-01

    The present invention concerns a device for detecting contamination of radioactive materials on the inner surface of a vessel upon reutilizing the vessel for containing solidified radioactive wastes and transporting them. Namely, the detecting device has following functions. (1) A radiation detector detects the radioactive materials on the inner surface of the vessel. (2) A plurality of proximity switches measure the distance from the radiation detector to the wall surface of the vessel and are actuated if the distance is decreased to a predetermined value, (3) A vessel inner surface position calculation mechanism calculates the position of the inner surface of the vessel based on the information from a direction indicator and a height indicator. (4) A frontal limit detector detects the limit for allowing the radiation detector to proceed. (5) A vessel inner shape judging mechanism for judging the shape of the inner side of the vessel based on the signals from the proximity switches in a state where the frontal limit detector is operated and a vessel inner surface position signal outputted from the vessel inner surface position calculation mechanism. As a result, the shape of the inner side of the vessel can accurately be recognized, thereby improving accuracy of radiation measurement. (I.S.)

  11. 40 CFR 141.61 - Maximum contaminant levels for organic contaminants.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant levels for organic contaminants. 141.61 Section 141.61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER... Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.61 Maximum contaminant...

  12. Radioactive contamination level of vehicles resulted from transporting fine rare-earth minerals by rail

    International Nuclear Information System (INIS)

    Han Kaichun; Yu Boyong; Gao Shengwei

    1997-01-01

    This paper presents monitoring results of radioactive contamination level of steel open wagon surface resulted from transporting fine rare-earth minerals. Under promising transport conditions (the packaging consists of two layers of plastic bags and two layers of plastic net sacks, each package contains 50 kg of minerals, each vehicle carries 60 t), the surface radioactivity (total α and total β) of 16 vehicles on two lines from Baotou to Wujiachuan (924 km) and from Baotou to Sankeshu (2236 km) was measured before loading, after unloading and washing, using α and β surface contamination detector. The results showed that the radioactive contamination level of the vehicle surface after unloading appeared significantly different. The contamination level of vehicle bases was higher than that of both sides, long distance vehicles was higher than that of short distance vehicles. The radioactive contamination level of vehicles surface after washing was below the standard limits, these vehicles can be used for ordinary goods transport

  13. Hard-surface contamination detection exercise. [Smears:a3

    Energy Technology Data Exchange (ETDEWEB)

    Kawa, S.

    1991-01-01

    The purpose of this thesis is to create a practical exercise which demonstrates the techniques used by Health Physicists to detect surface contamination, including both instrumentation and smear survey techniques. By understanding the basic principles of the most commonly found instruments the intent is that a new Health Physics graduate can correctly choose, and apply an instrument to their detection situation. The exercise is also intended to acquaint students with the very basic principles of smear techniques. Smear surveys are probably the most universally applied technique in this industry, however, very little literature exists on the subject. The techniques are usually taught, on-the-job and by demonstration. By their seeing and participating in this presentation, it is intended that Health Physics students can accelerate their first few weeks at their new careers, and enable them to recognize common mistakes. Health Physicists are expected to have knowledge of the basic practices of their profession. This exercise will allow Health Physics students to become familiar with the use of hand-held detection devices and the technique of smear surveys. Adequate measurement and recording of surface contamination information is necessary to: meet licensing requirements; protect the health and safety of the workers; maintain accurate records in the case of litigation or dose reconstruction; and maintain high levels of professional competency. This exercise will assist students in obtaining the skills necessary to adequately measure and record levels of surface contamination. 41 refs., 14 figs., 2 tabs.

  14. A new type of 3H surface-contamination monitor.

    Science.gov (United States)

    Aoyama, T; Watanabe, T

    1985-06-01

    A new type of 3H surface-contamination monitor has been developed which uses a windowless air proportional counter as the detector. The monitor offers several advantages. First, a high detection efficiency is obtained for 3H beta rays due to the windowless construction of the detector, permitting a minimum detection level of less than 10(-4) muCi cm-2 for surface contamination by 3H. Second, since no special gases other than room air are used as the counter gas, gas cylinders are not required thereby permitting increased convenience and lower costs. Finally, the detector is insensitive to external light due to the height discrimination of proportional counter pulses, which allows the monitor to be used in brightly illuminated places.

  15. Analysis of surface contaminants on beryllium and aluminum windows

    International Nuclear Information System (INIS)

    Gmur, N.F.

    1987-06-01

    An effort has been made to document the types of contamination which form on beryllium window surfaces due to interaction with a synchrotron radiation beam. Beryllium windows contaminated in a variety of ways (exposure to water and air) exhibited surface powders, gels, crystals and liquid droplets. These contaminants were analyzed by electron diffraction, electron energy loss spectroscopy, energy dispersive x-ray spectroscopy and wet chemical methods. Materials found on window surfaces include beryllium oxide, amorphous carbon, cuprous oxide, metallic copper and nitric acid. Aluminum window surface contaminants were also examined

  16. Developments in surface contamination and cleaning fundamentals and applied aspects

    CERN Document Server

    Kohli, Rajiv

    2015-01-01

    Developments in Surface Contamination and Cleaning, Vol. 1: Fundamentals and Applied Aspects, Second Edition, provides an excellent source of information on alternative cleaning techniques and methods for characterization of surface contamination and validation. Each volume in this series contains a particular topical focus, covering the key techniques and recent developments in the area. This volume forms the heart of the series, covering the fundamentals and application aspects, characterization of surface contaminants, and methods for removal of surface contamination. In addition, new cleaning techniques effective at smaller scales are considered and employed for removal where conventional cleaning techniques fail, along with new cleaning techniques for molecular contaminants. The Volume is edited by the leading experts in small particle surface contamination and cleaning, providing an invaluable reference for researchers and engineers in R&D, manufacturing, quality control, and procurement specific...

  17. 40 CFR 141.63 - Maximum contaminant levels (MCLs) for microbiological contaminants.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant levels (MCLs) for microbiological contaminants. 141.63 Section 141.63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Water Regulations: Maximum Contaminant Levels and Maximum Residual Disinfectant Levels § 141.63 Maximum...

  18. Modeling Groundwater-Surface Water Interaction and Contaminant Transport of Chlorinated Solvent Contaminated Site

    Science.gov (United States)

    Yimer Ebrahim, Girma; Jonoski, Andreja; van Griensven, Ann; Dujardin, Juliette; Baetelaan, Okke; Bronders, Jan

    2010-05-01

    Chlorinated-solvent form one of the largest groups of environmental chemicals. Their use and misuse in industry have lead to a large entry of these chemicals into the environment, resulting in widespread dissemination and oftentimes environmental contamination. Chlorinated solvent contamination of groundwater resources has been widely reported. For instance, there has been much interest in the assessment of these contaminant levels and their evolutions with time in the groundwater body below the Vilvoorde-Machelen industrial area (Belgium). The long industrial history of the area has lead to complex patterns of pollution from multiple sources and the site has been polluted to the extent that individual plumes are not definable any more. Understanding of groundwater/surface water interaction is a critical component for determining the fate of contaminant both in streams and ground water due to the fact that groundwater and surface water are in continuous dynamic interaction in the hydrologic cycle. The interaction has practical consequences in the quantity and quality of water in either system in the sense that depletion and/or contamination of one of the system will eventually affect the other one. The transition zone between a stream and its adjacent aquifer referred to as the hyporheic zone plays a critical role in governing contaminant exchange and transformation during water exchange between the two water bodies. The hyporheic zone of Zenne River ( the main receptor ) is further complicated due to the fact that the river banks are artificially trained with sheet piles along its reach extending some 12 m below the surface. This study demonstrates the use of MODFLOW, a widely used modular three-dimensional block-centred finite difference, saturated flow model for simulating the flow and direction of movement of groundwater through aquifer and stream-aquifer interaction and the use of transport model RT3D, a three-dimensional multi-species reactive transport model

  19. High level bacterial contamination of secondary school students' mobile phones.

    Science.gov (United States)

    Kõljalg, Siiri; Mändar, Rando; Sõber, Tiina; Rööp, Tiiu; Mändar, Reet

    2017-06-01

    While contamination of mobile phones in the hospital has been found to be common in several studies, little information about bacterial abundance on phones used in the community is available. Our aim was to quantitatively determine the bacterial contamination of secondary school students' mobile phones. Altogether 27 mobile phones were studied. The contact plate method and microbial identification using MALDI-TOF mass spectrometer were used for culture studies. Quantitative PCR reaction for detection of universal 16S rRNA, Enterococcus faecalis 16S rRNA and Escherichia coli allantoin permease were performed, and the presence of tetracycline ( tet A, tet B, tet M), erythromycin ( erm B) and sulphonamide ( sul 1) resistance genes was assessed. We found a high median bacterial count on secondary school students' mobile phones (10.5 CFU/cm 2 ) and a median of 17,032 bacterial 16S rRNA gene copies per phone. Potentially pathogenic microbes ( Staphylococcus aureus , Acinetobacter spp. , Pseudomonas spp., Bacillus cereus and Neisseria flavescens ) were found among dominant microbes more often on phones with higher percentage of E. faecalis in total bacterial 16S rRNA. No differences in contamination level or dominating bacterial species between phone owner's gender and between phone types (touch screen/keypad) were found. No antibiotic resistance genes were detected on mobile phone surfaces. Quantitative study methods revealed high level bacterial contamination of secondary school students' mobile phones.

  20. Improvement of a device for monitoring the contamination of surfaces

    International Nuclear Information System (INIS)

    Barbier, Albert.

    1981-01-01

    The purpose of this invention is to make it possible to monitor the contamination of surfaces by a light weight portable device and enabling the alpha, beta and gamma radiation contamination to be detected. The detection probe which is connected by a single lead to the box is adapted, in each particular case, to the radiation mode emitted by the contaminated surfaces and the box is provided with a special leak-proof socket for connecting the probe and includes means for assessing the counting rate of the radiation given off, depending on the mode of the radiations emitted by the contaminated surfaces and the intensity of the count rate [fr

  1. 40 CFR 141.50 - Maximum contaminant level goals for organic contaminants.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant level goals for organic contaminants. 141.50 Section 141.50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Maximum Contaminant Level...

  2. 40 CFR 141.52 - Maximum contaminant level goals for microbiological contaminants.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant level goals for microbiological contaminants. 141.52 Section 141.52 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Maximum Contaminant Level...

  3. Electronic Noses for Composites Surface Contamination Detection in Aerospace Industry.

    Science.gov (United States)

    Vito, Saverio De; Miglietta, Maria Lucia; Massera, Ettore; Fattoruso, Grazia; Formisano, Fabrizio; Polichetti, Tiziana; Salvato, Maria; Alfano, Brigida; Esposito, Elena; Francia, Girolamo Di

    2017-04-02

    The full exploitation of Composite Fiber Reinforced Polymers (CFRP) in so-called green aircrafts design is still limited by the lack of adequate quality assurance procedures for checking the adhesive bonding assembly, especially in load-critical primary structures. In this respect, contamination of the CFRP panel surface is of significant concern since it may severely affect the bonding and the mechanical properties of the joint. During the last years, the authors have developed and tested an electronic nose as a non-destructive tool for pre-bonding surface inspection for contaminants detection, identification and quantification. Several sensors and sampling architectures have been screened in view of the high Technology Readiness Level (TRL) scenarios requirements. Ad-hoc pattern recognition systems have also been devised to ensure a fast and reliable assessment of the contamination status, by combining real time classifiers and the implementation of a suitable rejection option. Results show that e-noses could be used as first line low cost Non Destructive Test (NDT) tool in aerospace CFRP assembly and maintenance scenarios.

  4. Surface Contamination by FTIR-PAS

    Science.gov (United States)

    Davis, Dennis M.; Hoffland, Lynn D.

    1985-12-01

    Fourier Transform Infrared Photoacoustic Spectroscopy (FTIR-PAS) is used to study the contamination of alkyd painted panels by liquids and solids. These alkyd painted panels are stainless steel panels coated with primer and an alkyd resin based paint which the Army uses for its vehicles. Portions of these panels were contaminated by dimethyl methyl phosphonate, tri-(2-ethylhexyl) phosphate, and triphenyl phosphate. The panels were then studied using FTIR-PAS, and the spectra identified.

  5. Characterization of silicon surface states at clean and copper contaminated condition via transient capacitance measurement

    Science.gov (United States)

    Song, Lihui; Xie, Meng; Yu, Xuegong; Yang, Deren

    2017-10-01

    Silicon surface is one of the dominant recombination sites for silicon solar cells. Generally, the recombination ability of silicon surface is characterized in terms of surface recombination velocity. However, silicon surface actually contain a series of donor and acceptor levels across the silicon band gap, and therefore the surface recombination velocity is too general to provide detailed information of the silicon surface states. In this paper, we used the measured transient capacitance data to extract the detailed information (like defect energy levels, defect densities, and capture cross sections) of the silicon surface states. Furthermore, the influence of copper contamination on silicon surface states was examined, and it was found that copper contamination can change the localized energy levels of "clean" silicon surface states to the band-like energy levels, meanwhile the defect densities and capture cross sections were both enlarged.

  6. Contaminant interferences with SIMS analyses of microparticle impactor residues on LDEF surfaces

    International Nuclear Information System (INIS)

    Simon, C.G.; Batchelor, D.; Griffis, D.P.; Hunter, J.L.; Misra, V.; Ricks, D.A.; Wortman, J.J.

    1992-01-01

    Elemental analyses of impactor residues on high purity surface exposed to the low earth orbit (LEO) environment for 5.8 years on Long Duration Exposure Facility (LDEF) has revealed several probable sources for microparticles at this altitude, including natural micrometeorites and manmade debris ranging from paint pigments to bits of stainless steel. A myriad of contamination interferences were identified and their effects on impactor debris identification mitigated during the course of this study. These interferences included pre-, post-, and in-flight deposited particulate surface contaminants, as well as indigenous heterogeneous material contaminants. Non-flight contaminants traced to human origins, including spittle and skin oils, contributed significant levels of alkali-rich carbonaceous interferences. A ubiquitous layer of in-flight deposited silicaceous contamination varied in thickness with location on LDEF and proximity to active electrical fields. In-flight deposited (low velocity) contaminants included urine droplets and bits of metal film from eroded thermal blankets

  7. Modeling of laser damage initiated by surface contamination

    International Nuclear Information System (INIS)

    Feit, M.D.; Rubenchik, A.M.; Faux, D.R.; Riddle, R.A.; Shapiro, A.; Eder, D.C.; Penetrante, B.M.; Milam, D.; Genin, F.Y.; Kozlowski, M.R.

    1996-11-01

    The authors are engaged in a comprehensive effort to understand and model the initiation and growth of laser damage initiated by surface contaminants. This includes, for example, the initial absorption by the contaminant, heating and plasma generation, pressure and thermal loading of the transparent substrate, and subsequent shockwave propagation, 'splashing' of molten material and possible spallation, optical propagation and scattering, and treatment of material fracture. The integration use of large radiation hydrodynamics codes, optical propagation codes and material strength codes enables a comprehensive view of the damage process The following picture of surface contaminant initiated laser damage is emerging from our simulations

  8. Contamination levels observed on the Belgian territory subsequent to the Chernobyl accident

    International Nuclear Information System (INIS)

    Cottens, E.

    1986-01-01

    A summary of the data from different laboratories concerning the fallout on the Belgian territory following the Chernobyl emissions is presented. The evolution of the particulate air activity at ground level, the integrated fallout captured in water, the deposition on soil surface directly for different localities in Belgium are given. The grass contamination, the milk contamination from individual farms, the concentration levels on leafy vegetables, surface waters and water basins and the contamination of meat during the month of May are presented. (A.F.)

  9. LASER CLEANING OF CONTAMINATED PAINTED SURFACES

    Energy Technology Data Exchange (ETDEWEB)

    Ames A. Grisanti; Charlene R. Crocker; Robert R. Jensen

    1999-11-19

    Several techniques are available or under development for surface decontamination in nuclear facilities. Each technique has its merits; however, none of them is universally the best choice for all surface decontamination applications. Because of the multitude of factors which influence the environmental and economic aspects of selecting a surface decontamination technique, it is difficult to select the best method in a given situation; an objective basis for comparing techniques is needed. The objective of this project was to develop a software tool for use by personnel selecting a surface decontamination technique. The software incorporates performance data for available surface decontamination techniques. The beta release version of the Surface Decontamination Assistant Software has been completed and has undergone testing at the Energy and Environmental Research Center. Minor modifications to the software were completed, and a final release version of the software is ready to be issued.

  10. Levels and trends of contaminants in humans of the Arctic.

    Science.gov (United States)

    Gibson, Jennifer; Adlard, Bryan; Olafsdottir, Kristin; Sandanger, Torkjel Manning; Odland, Jon Øyvind

    2016-01-01

    The Arctic Monitoring and Assessment Programme (AMAP) is one of the six working groups established under the Arctic Council. AMAP is tasked with monitoring the levels of contaminants present in the Arctic environment and people as well as assessing their effects on a continuous basis, and reporting these results regularly. Most of the presented data have been collected over the last 20 years and are from all eight Arctic countries. Levels of contaminants appear to be declining in some of the monitored Arctic populations, but it is not consistent across the Arctic. Most Arctic populations continue to experience elevated levels of these contaminants compared to other populations monitored globally. There are certain contaminants, such as perfluorinated compounds and polybrominated diphenyl ethers, which are still increasing in Arctic populations. These contaminants require more investigation to find out the predominant and important sources of exposure, and whether they are being transported to the Arctic through long-range transport in the environment.

  11. Analysis of surface contaminants on beryllium windows

    International Nuclear Information System (INIS)

    Gmur, N.F.

    1986-12-01

    It is known that various crystalline and liquid compounds form on the downstream surfaces of beryllium windows exposed to air. It is also known that the integrity of such windows may be compromised resulting in leaks through the window. The purpose of this report is to document the occurrences described as they pertain to the NSLS and to analyze, where possible, the various substances formed

  12. Release of Streptomyces albus propagules from contaminated surfaces

    International Nuclear Information System (INIS)

    Gorny, R.L.; Mainelis, Gediminas; Grinshpun, Sergey A.; Willeke, Klaus; Dutkiewicz, Jacek; Reponen, Tiina

    2003-01-01

    The release of Streptomyces albus propagules from contaminated agar an ceiling tile surfaces was studied under controlled environmental condition in a newly developed aerosolization chamber. The experiments revealed tha both spores and cell fragments can be simultaneously released from the colonized surface by relatively gentle air currents of 0.3 m s -1 . A 100x increase of the air velocity can result in a 50-fold increase in the number of released propagules. The aerosolization rate depends strongly on the typ and roughness of the contaminated surface. Up to 90% of available actinomycete propagules can become airborne during the first 10 min of th release process. Application of vibration to the surface did not reveal an influence on the aerosolization process of S. albus propagules under th tested conditions. This study has shown that propagules in the fine particle size range can be released in large amounts from contaminated surfaces Measurement of the number of S. albus fragments in the vicinity of contaminated area, as an alternative to conventional air or surface sampling appears to be a promising approach for quantitative exposure assessment

  13. Removal of lead contaminated dusts from hard surfaces.

    Science.gov (United States)

    Lewis, Roger D; Condoor, Sridhar; Batek, Joe; Ong, Kee Hean; Backer, Denis; Sterling, David; Siria, Jeff; Chen, John J; Ashley, Peter

    2006-01-15

    Government guidelines have widely recommended trisodium phosphate (TSP) or "lead-specific" cleaning detergents for removal of lead-contaminated dust (LCD) from hard surfaces, such as floors and window areas. The purpose of this study was to determine if low-phosphate, non-lead-specific cleaners could be used to efficiently remove LCD from 3 types of surfaces (vinyl flooring, wood, and wallpaper). Laboratory methods were developed and validated for simulating the doping, embedding, and sponge cleaning of the 3 surface types with 4 categories of cleaners: lead-specific detergents, nonionic cleaners, anionic cleaners, and trisodium phosphate (TSP). Vinyl flooring and wood were worn using artificial means. Materials were ashed, followed by ultrasound extraction, and anodic stripping voltammetry (ASV). One-way analysis of variance approach was used to evaluate the surface and detergent effects. Surface type was found to be a significant factor in removal of lead (p < 0.001). Vinyl flooring cleaned better than wallpaper by over 14% and wood cleaned better than wallpaper by 13%. There was no difference between the cleaning action of vinyl flooring and wood. No evidence was found to support the use of TSP or lead-specific detergents over all-purpose cleaning detergents for removal of lead-contaminated dusts. No-phosphate, non-lead-specific detergents are effective in sponge cleaning of lead-contaminated hard surfaces and childhood lead prevention programs should consider recommending all-purpose household detergents for removal of lead-contaminated dust after appropriate vacuuming.

  14. Assessment of low levels of radioactive contamination

    International Nuclear Information System (INIS)

    Gray, P.W.

    1988-01-01

    This report describes a general methodology for the verification and clearance of sites contaminated with radioactive materials; general expressions for the risk or health detriment are derived. Techniques are developed, using Bayesian decision theory, to optimize the resources allocated to a site monitoring procedure, and to construct the probability distribution of the spatial distribution of specific activity within a site. A technique is also developed to determine the probability that a localized source of specified characteristics will not be detected by the monitoring procedure employed. The application of these techniques is illustrated by means of simple examples. This report confirms that a very large number of measurements are needed if a source of localized activity is to be detected with a high probability, and demonstrates how prior information about past radiological practices might be used to increase the probability of detection. Proposals are made for a programme of research to determine whether or not representative sites can be verified using current measuring techniques. (author)

  15. Materials SIG quantification and characterization of surface contaminants

    Science.gov (United States)

    Crutcher, E. Russ

    1992-01-01

    When LDEF entered orbit its cleanliness was approximately a MIL-STD-1246B Level 2000C. Its burden of contaminants included particles from every part of its history including a relatively small contribution from the shuttle bay itself. Although this satellite was far from what is normally considered clean in the aerospace industry, contaminating events in orbit and from processing after recovery were easily detected. The molecular contaminants carried into orbit were dwarfed by the heavy deposition of UV polymerized films from outgassing urethane paints and silicone based materials. Impacts by relatively small objects in orbit could create particulate contaminants that easily dominated the particle counts within a centimeter of the impact site. During the recovery activities LDEF was 'sprayed' with a liquid high in organics and water soluble salts. With reentry turbulence, vibration, and gravitational loading particulate contaminants were redistributed about LDEF and the shuttle bay.

  16. A New Method for Processing Airborne Gamma Ray Spectrometry Data for Mapping Low Level Contaminations

    DEFF Research Database (Denmark)

    Aage, Helle Karina; Korsbech, Uffe C C; Bargholz, Kim

    1999-01-01

    where the remaining contamination from the 1986 Chernobyl accident together with fallout from the atmospheric nuclear weapon tests includes Cs-137 at levels often well below 1 kBq/m(2) equivalent surface contamination. The limiting factors for obtaining reliable results are radon in the air, spectrum......A new technique for processing airborne gamma ray spectrometry data has been developed. It is based on the noise adjusted singular value decomposition method introduced by Hovgaard in 1997. The new technique opens for mapping of very low contamination levels. It is tested with data from Latvia...

  17. 40 CFR 141.62 - Maximum contaminant levels for inorganic contaminants.

    Science.gov (United States)

    2010-07-01

    ... section 1412 of the Act, hereby identifies the following as the best technology, treatment technique, or other means available for achieving compliance with the maximum contaminant levels for inorganic...

  18. 40 CFR 141.51 - Maximum contaminant level goals for inorganic contaminants.

    Science.gov (United States)

    2010-07-01

    ... (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Maximum Contaminant Level... Lead zero Mercury 0.002 Nitrate 10 (as Nitrogen). Nitrite 1 (as Nitrogen). Total Nitrate+Nitrite 10 (as...

  19. Environmental contaminants of emerging concern in seafood – European database on contaminant levels

    International Nuclear Information System (INIS)

    Vandermeersch, Griet; Lourenço, Helena Maria; Alvarez-Muñoz, Diana; Cunha, Sara; Diogène, Jorge; Cano-Sancho, German; Sloth, Jens J.; Kwadijk, Christiaan; Barcelo, Damia; Allegaert, Wim; Bekaert, Karen; Fernandes, José Oliveira; Marques, Antonio

    2015-01-01

    Marine pollution gives rise to concern not only about the environment itself but also about the impact on food safety and consequently on public health. European authorities and consumers have therefore become increasingly worried about the transfer of contaminants from the marine environment to seafood. So-called “contaminants of emerging concern” are chemical substances for which no maximum levels have been laid down in EU legislation, or substances for which maximum levels have been provided but which require revision. Adequate information on their presence in seafood is often lacking and thus potential risks cannot be excluded. Assessment of food safety issues related to these contaminants has thus become urgent and imperative. A database ( (www.ecsafeseafooddbase.eu)), containing available information on the levels of contaminants of emerging concern in seafood and providing the most recent data to scientists and regulatory authorities, was developed. The present paper reviews a selection of contaminants of emerging concern in seafood including toxic elements, endocrine disruptors, brominated flame retardants, pharmaceuticals and personal care products, polycyclic aromatic hydrocarbons and derivatives, microplastics and marine toxins. Current status on the knowledge of human exposure, toxicity and legislation are briefly presented and the outcome from scientific publications reporting on the levels of these compounds in seafood is presented and discussed. - Highlights: • Development of a European database regarding contaminants of emerging concern. • Current status on knowledge of human exposure, toxicity and legislation. • Review on the occurrence of contaminants of emerging concern in seafood.

  20. Monitoring of tritium-contaminated surfaces, including skin

    International Nuclear Information System (INIS)

    Surette, R.A.; Wood, M.J.

    1994-05-01

    We have examined various commercially available tritium surface contamination monitors along with different swipe media and techniques for direct and indirect (swipe) monitoring of contaminated surfaces, including skin. None of the methods or instruments evaluated were more sensitive than the swipe and liquid scintillation counting (LSC) method. Swipe measurements with open-window proportional counters were, in general, less than half as sensitive as LSC, but have the advantages of having the results available almost immediately, and no sample preparation is required. The Nuclear Measurement Corporation's PC-55 is the most suitable instrument we tested for the analysis of routine swipe measurement. The PC-55 was about one third as sensitive as LSC when used with Ontario Hydro filter paper swipe media. Surface contamination measurement results can be obtained within minutes using the PC-55, compared to hours using LSC. The selection of swipe media for use with proportional counter-based instruments is critical. A medium that is electrically insulating can develop an electrostatic charge on its surface; this may alter the field gradient in the detector and may adversely influence the results. Although the PC-55 is sufficiently sensitive and very convenient, operational experience with the instrument is needed before recommending that it replace current LSC methods. The PC-55's susceptibility to internal tritium contamination may limit its practical usefulness. Because of the complexity of using live animals to evaluate direct and indirect methods for assessing skin contamination, pig skin was investigated as a possible substitute. We concluded that, for the first few hours post-exposure, pig skin mimics the kinetics of animal skin that has contacted a tritium-contaminated surface. (author). 30 refs., 1 tab., 7 figs

  1. Modelling of contamination of surface atmosphere for deflation of Cesium-137 on contaminated territories

    International Nuclear Information System (INIS)

    Bogdanov, A.P.; Zhmura, G.M.

    1994-01-01

    Presence of Cesium 137 in near land air is caused at the contaminated territories by 'local' dusting and transport of the dust from the zone of strong contamination. For large distance is it caused by resuspension of radioactive dust from the surface in the given region. In accordance with the models of dusting round square sources based on Gauss statistical model of dissemination of admixtures in the atmosphere, the contaminated areas of european part of the former of USSR with the density of contamination over 1 Ci/km 2 with Cesium 137 were represented by 30 round square sources covering the main spots of contamination. The results of calculation of contamination of the atmosphere for several cities of Belarus, Russia and Ukraine, where there are the permanent points of observation for the content of radionuclides in the air, have shown that the proposed model of dusting sources describes the contamination of near land air with Cesium 137 reasonably well. 7 refs., 3 tabs

  2. Allowable residual contamination levels for decommissioning. Part 2. A summary of example results

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Napier, B.A.

    1985-01-01

    This paper contains a description of the results of a study sponsored by UNC Nuclear Industries to determine Allowable Residual Contamination Levels (ARCL) for decommissioning facilities in the 100 Areas of the Hanford Site. ARCL results are presented both for surface contamination remaining in facilities (in dpm/100 cm 2 ) and for unconfined surface and confined subsurface soil conditions (in pCi/g). Two confined soil conditions are considered: contamination at depths between 1 and 4 m, and contamination at depths greater than or equal to 5 m. A set of worksheets are discussed for modifying the ARCL values to accommodate changes in the radionuclide mixture or concentrations, to consider the impacts of radioactive decay, and to predict instrument responses. Finally, a comparison is made between the unrestricted release ARCL values for the 100 Area facilities and existing decommissioning and land disposal regulations. For surface contamination, the comparison shows good agreement for a selected annual dose limit. For soil contamination, the comparison shows good agreement if reasonable modification factors are applied to account for the differences in modeling soil contamination and licensed low-level waste. 6 references, 1 figures, 4 tables

  3. Surface soil contamination standards for Rockwell Hanford Operations

    International Nuclear Information System (INIS)

    Boothe, G.F.

    1981-01-01

    The 200 Areas of the Hanford site contain soils contaminated with levels of radioactivity ranging from fallout concentrations to levels requiring radiological controls. Some contamination is more or less uniformly distributed, and some occurs as discrete specks or spots of activity. Because of the acute need for standards, the Rockwell Environmental Protection (EP) Group proceeded to develop standards; these were approved by Rockwell in October 1979. It must be emphasized that these standards are only applicable to the 200 Areas of the Hanford site or other areas under Rockwell's jurisdiction. It is assumed that access to these areas will always be restricted and that land-use restrictions will be maintained. Contamination limits for areas used by the general public would normally be lower than the limits derived in this case. It appears that the Rockwell standards divided by a factor of 5 to 10 may be reasonable contamination guidelines for the general environment

  4. Environmental contaminants of emerging concern in seafood - European database on contaminant levels

    DEFF Research Database (Denmark)

    Vandermeersch, Griet; Lourenço, Helena Maria; Alvarez-Muñoz, Diana

    2015-01-01

    to seafood.So-called "contaminants of emerging concern" are chemical substances for which no maximum levels have been laid down in EU legislation, or substances for which maximum levels have been provided but which require revision. Adequate information on their presence in seafood is often lacking and thus...... potential risks cannot be excluded. Assessment of food safety issues related to these contaminants has thus become urgent and imperative. A database (www.ecsafeseafooddbase.eu), containing available information on the levels of contaminants of emerging concern in seafood and providing the most recent data...... to scientists and regulatory authorities, was developed.The present paper reviews a selection of contaminants of emerging concern in seafood including toxic elements, endocrine disruptors, brominated flame retardants, pharmaceuticals and personal care products, polycyclic aromatic hydrocarbons and derivatives...

  5. Explosive Contamination from Substrate Surfaces: Differences and Similarities in Contamination Techniques using RDX and C-4

    Energy Technology Data Exchange (ETDEWEB)

    C.J. Miller; T.S. Yoder

    2010-06-01

    The amount of time that an explosive is present on the surface of a material is dependent upon the original amount of explosive on the surface, temperature, humidity, rain, etc. This laboratory study focused on looking at similarities and differences in three different surface contamination techniques that are used when performance testing explosive trace detection equipment in an attempt to determine how effective the techniques are at replicating actual field samples. The three techniques used were dry transfer deposition of solutions using the Transportation Security Laboratory (TSL) patented dry transfer techniques (US patent 6470730), direct deposition of explosive standards, and fingerprinting of actual explosives. Explosives were deposited on the surface of one of five substrates using one of the three different deposition techniques. The process was repeated for each surface type using each contamination technique. The surface types used were: 50% cotton/50% polyester as found in T-shirts, 100% cotton with a smooth surface such as that found in a cotton dress shirt, 100% cotton on a rough surface such as that found on canvas or denim, suede leather such as might be found on jackets, purses, or shoes, and metal obtained from a car hood at a junk yard. The samples were not pre-cleaned prior to testing and contained sizing agents, and in the case of the metal, oil and dirt. The substrates were photographed using a Zeiss Discover V12 stereoscope with Axiocam ICc1 3 megapixel digital camera to determine the difference in the crystalline structure and surface contamination in an attempt to determine differences and similarities associated with current contamination techniques.

  6. Purification the surface of detail from biological contaminations

    International Nuclear Information System (INIS)

    Gabdrakhmanov, Az T; Israphilov, I H; Galiakbarov, A T; Gabdrakhmanov, Al T

    2017-01-01

    More than 70% of biodegradation occur due to the corrosion processes. A biological corrosion causes the greatest damage to the oil and gas-production industry, the Navy and pipelines, constructions of water supply, means of communication. This paper proposes an effective method of purification various surfaces from biological contaminations by using of cold plasma. (paper)

  7. Removing device and method for radiation-contaminated concrete surface layer

    International Nuclear Information System (INIS)

    Ida, Kiyoshi.

    1996-01-01

    When a radiation-contaminated concrete surface layer is crushed, peeled or melted, and the products generated by the procedures are captured by sucking, the activity of the products is measured. It is judged whether the result is higher than a predetermined level or not, and when the activity is lowered to a predetermined level or less, the portion to be crushed, peeled or melted is moved and the radiation-contaminated concrete surface layer is thus successively removed. In the device of the present invention, microwave energy, millimeter wave energy, or AC arc plasma is used as an energy irradiation means. With such procedures, the contaminated concrete surface layer can be removed efficiently with neither more nor less. (T.M.)

  8. Enzyme-enabled responsive surfaces for anti-contamination materials.

    Science.gov (United States)

    Wu, Songtao; Buthe, Andreas; Jia, Hongfei; Zhang, Minjuan; Ishii, Masahiko; Wang, Ping

    2013-06-01

    Many real-life stains have origins from biological matters including proteins, lipids, and carbohydrates that act as gluing agents binding along with other particulates or microbes to exposed surfaces of automobiles, furniture, and fabrics. Mimicking naturally occurring self-defensive processes, we demonstrate in this work that a solid surface carrying partially exposed enzyme granules protected the surface in situ from contamination by biological stains and fingerprints. Attributed to the activities of enzymes which can be made compatible with a wide range of materials, such anti-contamination and self-cleaning functionalities are highly selective and efficient toward sticky chemicals. This observation promises a new mechanism in developing smart materials with desired anti-microbial, self-reporting, self-cleaning, or self-healing functions. Copyright © 2013 Wiley Periodicals, Inc.

  9. Salinization and arsenic contamination of surface water in southwest Bangladesh.

    Science.gov (United States)

    Ayers, John C; George, Gregory; Fry, David; Benneyworth, Laura; Wilson, Carol; Auerbach, Leslie; Roy, Kushal; Karim, Md Rezaul; Akter, Farjana; Goodbred, Steven

    2017-09-11

    To identify the causes of salinization and arsenic contamination of surface water on an embanked island (i.e., polder) in the tidal delta plain of SW Bangladesh we collected and analyzed water samples in the dry (May) and wet (October) seasons in 2012-2013. Samples were collected from rice paddies (wet season), saltwater ponds used for brine shrimp aquaculture (dry season), freshwater ponds and tidal channels (both wet and dry season), and rainwater collectors. Continuous measurements of salinity from March 2012 to February 2013 show that tidal channel water increases from ~0.15 ppt in the wet season up to ~20 ppt in the dry season. On the polder, surface water exceeds the World Health Organization drinking water guideline of 10 μg As/L in 78% of shrimp ponds and 27% of rice paddies, raising concerns that produced shrimp and rice could have unsafe levels of As. Drinking water sources also often have unsafe As levels, with 83% of tubewell and 43% of freshwater pond samples having >10 μg As/L. Water compositions and field observations are consistent with shrimp pond water being sourced from tidal channels during the dry season, rather than the locally saline groundwater from tubewells. Irrigation water for rice paddies is also obtained from the tidal channels, but during the wet season when surface waters are fresh. Salts become concentrated in irrigation water through evaporation, with average salinity increasing from 0.43 ppt in the tidal channel source to 0.91 ppt in the rice paddies. Our observations suggest that the practice of seasonally alternating rice and shrimp farming in a field has a negligible effect on rice paddy water salinity. Also, shrimp ponds do not significantly affect the salinity of adjacent surface water bodies or subjacent groundwater because impermeable shallow surface deposits of silt and clay mostly isolate surface water bodies from each other and from the shallow groundwater aquifer. Bivariate plots of conservative element

  10. Experiment on Physical Desalinisation of Uranium-contaminated Gravel Surface

    International Nuclear Information System (INIS)

    Park, Uk-Ryang; Kim, Gye-Nam; Kim, Seung-Soo; Han, Gyu-Seong; Moon, Jai-Kwon

    2014-01-01

    As a result, the method to wash uranium-contaminated gravels could not get satisfactory desalinization rate. During the long oxidization process it was judged that uranium penetrated inside the gravels, so we tried to increase the desalinization rate by fragmentizing them into pieces and then washing them. The desalinization rate after fragmentizing the gravels into pieces and washing them brought a satisfactory result.. However, we could obtain desired concentration for gravels with high uranium concentration by fragmentizing them and breaking them further into even smaller pieces. Likewise, desalinization using soil washing process is complicated and has to go through multiple washing steps, resulting in too much of waste fluid generated accordingly. The increase of waste fluid generated leads to the increase in by-products of the final disposal process later on, bringing a not good economic result. Furthermore, taking into account that the desalinization rate is 65% during soil washing process, it is expected that gravel washing will show a similar desalinization result; it is considered uneasy to have a perfect desalinization only by soil washing. The grinding method is actually used in the primary desalinization process in order to desalinize radioactivity-contaminated concrete. This method does desalinization by grinding the radioactivity-contaminated area of the concrete surface with desalinization equipment, which enables a near-to-perfect desalinization for relatively thinly contaminated surface. Likewise, this research verified the degree of desalinization by applying the grinding method and comparing it to the fragmentizing-washing method, and attempted to find a method to desalinize uranium-contaminated gravels more effectively. In order to desalinize uranium-contaminated gravels more effectively and compare to the existing washing-desalinization method, we conducted a desalinization experiment with grinding method that grinds gravel surface. As a

  11. Contamination levels of domestic water sources in Maiduguri ...

    African Journals Online (AJOL)

    The study examines the levels of contamination of domestic water sources in Maiduguri Metropolis area of Borno State based on their physicochemical and bacteriological properties. It was informed by the global concern on good drinking water quality which is an indicator of development level; hence the focus on domestic ...

  12. Development of an automatic smear sampler and a polymer film for surface radioactive contamination assay

    International Nuclear Information System (INIS)

    Seo, B.-K.; Lee, K.-W.; Woo, Z.-H.; Jeong, K.-S.; Oh, W.-Z.; Han, M.-J.

    2004-01-01

    Measurement of the surface contamination by an indirect method is subject to the various kinds of error according to the sampling person and needs much time and effort in the sampling and assay. In this research, an automatic smear sampler is developed. It improved efficiency for assay work of surface contamination level achieved periodically in a radiation controlled area. Using an automatic smear sampler developed, it is confirmed that radioactive contaminated materials are uniformly transferred to smear paper more than any sampling method by an operator. Also, Solid scintillation proximity membranes were prepared for measuring the amount of radioactive contamination in laboratories contaminated by the low energy beta-ray emitter, such as 3 H and 14 C. Polysulfone scintillation proximity membranes were prepared by impregnating Cerium Activated Yttrium Silicate (CAYS), an inorganic fluor, in a membrane structure. The inorganic fluor-impregnated membranes were applied to detect the radioactive surface contamination. The preparation of membranes was divided into two processes. A supporting polymer film was made of casting solutions consisting of polysulfone and solvent, their cast film being solidified by vacuum evaporation. CAYS-dispersed polymer solutions were cast over the first, solidified polymer films and coagulated either by evaporating solvent in the solution with non-solvent in a coagulation bath. The prepared membranes had two distinguished, but tightly attached, double layers : one is the supporting layer of dense polymer film and the other results revealed that the prepared membranes were efficient to monitor radioactive contamination with reliable counting ability. For enhancement of pick-up and measurement efficiency, the membrane was prepared with the condition of different membrane solidification. The scintillation produced by interaction with radiation and CAYS was measured with photomultiplier tube. The test results showed that the prepared

  13. Surface contamination of hazardous drug pharmacy storage bins and pharmacy distributor shipping containers.

    Science.gov (United States)

    Redic, Kimberly A; Fang, Kayleen; Christen, Catherine; Chaffee, Bruce W

    2018-03-01

    Purpose This study was conducted to determine whether there is contamination on exterior drug packaging using shipping totes from the distributor and carousel storage bins as surrogate markers of external packaging contamination. Methods A two-part study was conducted to measure the presence of 5-fluorouracil, ifosfamide, cyclophosphamide, docetaxel and paclitaxel using surrogate markers for external drug packaging. In Part I, 10 drug distributor shipping totes designated for transport of hazardous drugs provided a snapshot view of contamination from regular use and transit in and out of the pharmacy. An additional two totes designated for transport of non-hazardous drugs served as controls. In Part II, old carousel storage bins (i.e. those in use pre-study) were wiped for snapshot view of hazardous drug contamination on storage bins. New carousel storage bins were then put into use for storage of the five tested drugs and used for routine storage and inventory maintenance activities. Carousel bins were wiped at time intervals 0, 8, 16 and 52 weeks to measure surface contamination. Results Two of the 10 hazardous shipping totes were contaminated. Three of the five-old carousel bins were contaminated with cyclophosphamide. One of the old carousel bins was also contaminated with ifosfamide. There were no detectable levels of hazardous drugs on any of the new storage bins at time 0, 8 or 16 weeks. However, at the Week 52, there was a detectable level of 5-FU present in the 5-FU carousel bin. Conclusions Contamination of the surrogate markers suggests that external packaging for hazardous drugs is contaminated, either during the manufacturing process or during routine chain of custody activities. These results demonstrate that occupational exposure may occur due to contamination from shipping totes and storage bins, and that handling practices including use of personal protective equipment is warranted.

  14. Reactor surface contamination stabilization. Innovative technology summary report

    International Nuclear Information System (INIS)

    1998-11-01

    Contaminated surfaces, such as the face of a nuclear reactor, need to be stabilized (fixed) to avoid airborne contamination during decontamination and decommissioning activities, and to prepare for interim safe storage. The traditional (baseline) method of fixing the contamination has been to spray a coating on the surfaces, but ensuring complete coverage over complex shapes, such as nozzles and hoses, is difficult. The Hanford Site C Reactor Technology Demonstration Group demonstrated innovative technologies to assess stabilization properties of various coatings and to achieve complete coverage of complex surfaces on the reactor face. This demonstration was conducted in two phases: the first phase consisted of a series of laboratory assessments of various stabilization coatings on metal coupons. For the second phase, coatings that passed the laboratory tests were applied to the front face of the C Reactor and evaluated. The baseline coating (Rust-Oleum No. 769) and one of the innovative technologies did not completely cover nozzle assemblies on the reactor face, the most critical of the second-phase evaluation criteria. However, one of the innovative coating systems, consisting of a base layer of foam covered by an outer layer of a polymeric film, was successful. The baseline technology would cost approximately 33% as much as the innovative technology cost of $64,000 to stabilize an entire reactor face (196 m 2 or 2116 ft 2 ) with 2,004 nozzle assemblies, but the baseline system failed to provide complete surface coverage

  15. Environmental contaminants of emerging concern in seafood--European database on contaminant levels.

    Science.gov (United States)

    Vandermeersch, Griet; Lourenço, Helena Maria; Alvarez-Muñoz, Diana; Cunha, Sara; Diogène, Jorge; Cano-Sancho, German; Sloth, Jens J; Kwadijk, Christiaan; Barcelo, Damia; Allegaert, Wim; Bekaert, Karen; Fernandes, José Oliveira; Marques, Antonio; Robbens, Johan

    2015-11-01

    Marine pollution gives rise to concern not only about the environment itself but also about the impact on food safety and consequently on public health. European authorities and consumers have therefore become increasingly worried about the transfer of contaminants from the marine environment to seafood. So-called "contaminants of emerging concern" are chemical substances for which no maximum levels have been laid down in EU legislation, or substances for which maximum levels have been provided but which require revision. Adequate information on their presence in seafood is often lacking and thus potential risks cannot be excluded. Assessment of food safety issues related to these contaminants has thus become urgent and imperative. A database (www.ecsafeseafooddbase.eu), containing available information on the levels of contaminants of emerging concern in seafood and providing the most recent data to scientists and regulatory authorities, was developed. The present paper reviews a selection of contaminants of emerging concern in seafood including toxic elements, endocrine disruptors, brominated flame retardants, pharmaceuticals and personal care products, polycyclic aromatic hydrocarbons and derivatives, microplastics and marine toxins. Current status on the knowledge of human exposure, toxicity and legislation are briefly presented and the outcome from scientific publications reporting on the levels of these compounds in seafood is presented and discussed. Copyright © 2015 Elsevier Inc. All rights reserved.

  16. Comparison of contaminants from different trophic levels and ecosystems

    DEFF Research Database (Denmark)

    Dietz, R.; Riget, F.; Cleemann, M.

    2000-01-01

    The present paper provides an overview of the priority contaminants and media from the Greenland part of the Arctic Monitoring and Assessment Program. Levels and accumulation patterns of heavy metals, POPs and a radionuclide (Cs-137) are compared from the terrestrial, freshwater and marine...... ecosystems. Of the nine compounds presented, seven (Cd, Hg, Se, Sigma PCB, Sigma DDT, Sigma HCH, HCB) increased in concentration towards higher trophic levels. For these contaminants the concentrations in soil and aquatic sediment were in the same order of magnitude, whereas the concentrations in marine...

  17. Removable coating for contamination protection of concrete surface

    International Nuclear Information System (INIS)

    Brambilla, G.; Beaulardi, L.

    1985-01-01

    In order to research protective coatings for concrete surfaces, assuring an effective protection against contamination and that it be easily removed before dismantling the structures, commercial stripping paints have been characterized for their conventional and nuclear properties: water and chemicals, abrasion, impact, tensile stress resistance, stripping capacity, decontaminability. The protective power of the coatings against contamination has been checked by recording the surface activity before and after stripping the paint film: the activity filtered through the coating was, in any case, very low (< 1% of the deposited activity). Indications from large scale application of a stripping paint in NUCLEO (Rome) establishments and technical evaluation of the possible utilization of removable coatings in the CAORSO Nuclear Power Station, are also reported

  18. Hanford Site surface soil radioactive contamination control plan, March 1993

    International Nuclear Information System (INIS)

    Mix, P.D.; Winship, R.A.

    1993-04-01

    The Decommissioning and Resource Conservation and Recovery Act Closure Program is responsible to the US Department of Energy Richland Field Office, for the safe and cost-effective surveillance, maintenance, and decommissioning of surplus facilities and Resource Conservation and Recovery Act of 1976 closures at the Hanford Site. This program also manages the Radiation Area Remedial Action that includes the surveillance, maintenance, decontamination, and/or interim stabilization of inactive burial grounds, cribs, ponds, trenches, and unplanned release sites. This plan addresses only the Radiation Area Remedial Action activity requirements for managing and controlling the contaminated surface soil areas associated with these inactive sites until they are remediated as part of the Hanford Site environmental restoration process. All officially numbered Radiation Area Remedial Action and non-Radiation Area Remedial Action contaminated surface soil areas are listed in this document so that a complete list of the sites requiring remediation is contained in one document

  19. Levels of chlorinated, brominated, and perfluorinated contaminants in birds of prey spanning multiple trophic levels.

    Science.gov (United States)

    Yordy, Jennifer E; Rossman, Sam; Ostrom, Peggy H; Reiner, Jessica L; Bargnesi, Keely; Hughes, Stacy; Elliot, James D

    2013-04-01

    Birds of prey occupy high trophic levels and can consequently bioaccumulate high levels of environmental contaminants. To evaluate exposure to past- and current-use pollutants, we measured legacy contaminants (i.e., polychlorinated biphenyls [PCBs]; organochlorine pesticides, e.g., DDT), contaminants of emerging concern (polybrominated diphenyl ethers [PBDEs]; perfluorinated compounds [PFCs]), and stable isotopes (δ(13)C, δ(15)N) in 26 birds of prey (10 species) from coastal South Carolina (USA) sampled in 2009 and 2010. Nitrogen isotope ratios (δ(15)N) ranged from 5.2% to 13.7%, indicating the birds of prey spanned two to three trophic levels. Legacy contaminant levels were highly variable but generally comparable to levels reported previously for birds of prey in the southeast US, suggesting exposure has not declined substantially over the past 40 yr. Despite their status as newly emerging environmental contaminants, PFC levels were within the same order of magnitude as legacy contaminants. Although PBDEs were less prevalent, levels were among the greatest observed in wildlife to date (∑PBDEs max. 200 μg/g lipid). Relative contaminant profiles also varied between birds of prey utilizing low and high trophic levels; specifically PFCs contributed to a larger proportion of the contaminant burden in birds utilizing high trophic levels, whereas the legacy pesticide mirex was a larger contributor in low-trophic-level birds, indicating that relative exposure is in part dependent on foraging ecology. This study demonstrates that birds of prey continue to face exposure to legacy contaminants as well as newly emerging contaminants at levels of concern.

  20. Calibration and verification of surface contamination meters --- Procedures and techniques

    International Nuclear Information System (INIS)

    Schuler, C; Butterweck, G.; Wernli, C.; Bochud, F.; Valley, J.-F.

    2007-03-01

    A standardised measurement procedure for surface contamination meters (SCM) is presented. The procedure aims at rendering surface contamination measurements to be simply and safely interpretable. Essential for the approach is the introduction and common use of the radionuclide specific quantity 'guideline value' specified in the Swiss Radiation Protection Ordinance as unit for the measurement of surface activity. The according radionuclide specific 'guideline value count rate' can be summarized as verification reference value for a group of radionuclides ('basis guideline value count rate'). The concept can be generalized for SCM of the same type or for SCM of different types using he same principle of detection. A SCM multi source calibration technique is applied for the determination of the instrument efficiency. Four different electron radiation energy regions, four different photon radiation energy regions and an alpha radiation energy region are represented by a set of calibration sources built according to ISO standard 8769-2. A guideline value count rate representing the activity per unit area of a surface contamination of one guideline value can be calculated for any radionuclide using instrument efficiency, radionuclide decay data, contamination source efficiency, guideline value averaging area (100 cm 2 ), and radionuclide specific guideline value. n this way, instrument responses for the evaluation of surface contaminations are obtained for radionuclides without available calibration sources as well as for short-Iived radionuclides, for which the continuous replacement of certified calibration sources can lead to unreasonable costs. SCM verification is based on surface emission rates of reference sources with an active area of 100 cm 2 . The verification for a given list of radionuclides is based on the radionuclide specific quantity guideline value count rate. Guideline value count rates for groups of radionuclides can be represented within the maximum

  1. Removal of Microbial Contamination from Surface by Plasma

    Science.gov (United States)

    Feng, Xinxin; Liu, Hongxia; Shen, Zhenxing; Wang, Taobo

    2018-01-01

    Microbial contamination is closely associated with human and environmental health, they can be tested on food surfaces, medical devices, packing material and so on. In this paper the removal of the microbial contamination from surface using plasma treatment is investigated. The Escherichia coli (E. coli) has been chosen as a bio-indicator enabling to evaluate the effect of plasma assisted microbial inactivation. Oxygen gas was as the working gas. The plasma RF power, plasma exposition time, gas flow and the concentration of organic pollutant were varied in order to see the effect of the plasma treatment on the Gram-negative germ removal. After the treatment, the microbial abatement was evaluated by the standard plate count method. This proved a positive effect of the plasma treatment on Gram-negative germ removal. The kinetics and mathematical model of removal were studied after plasma treatment, and then the removing course of E. coli was analyzed. This work is meaningful for deepening our understanding of the fundamental scientific principles regarding microbial contamination from surface by plasma.

  2. Application Of The SPV-based Surface Lifetime Technique To In-Line Monitoring Of Surface Cu Contamination

    Science.gov (United States)

    D'Amico, John; Savtchouk, Alexandre; Wilson, Matthew; Kim, Chul Hong; Yoo, Hyung Won; Lee, Chang Hwan; Kim, Tae Kyoung; Son, Sang Hoon

    2009-09-01

    Implementation of Cu interconnects into Silicon Integrated Circuits (IC's) has been instrumental in the continuing improvement of IC device performance. Copper as a well known Gate Oxide Integrity (GOI) killer [1, 2] requires extensive protocols to minimize the possibility of cross contamination. Despite such protocols the risk for cross contamination exists, and consequently there is the need for in-line Cu cross-contamination detection metrology. Preferably the metrology will be non-destructive, fast, and capable of mapping on product wafers. Up to now the most common approaches for monitoring Cu contamination in IC fabrication lines either measure Cu in the bulk Si, which is not applicable to Cu cross-contamination monitoring because Back-End-of-the-Line thermal budgets restrict the ability to diffuse the surface Cu into the bulk Si; or the techniques are not optimal for in-line monitoring due to their destructive, time-consuming, or costly nature. In this work we demonstrate for the first time the application of the ac-Surface Photo Voltage (ac-SPV) surface lifetime approach [3] to in-line, full wafer coverage mapping of low level (metrology system. Furthermore, because the metrology is non-contact (utilizing edge-grip handling) and non-destructive, it is directly applicable to measurement of production wafers. In-line fab data acquired using this metrology is presented and compared to data from Inductively Coupled Plasma Mass Spectroscopy (ICP-MS).

  3. Residual radioactive contamination from decommissioning: Technical basis for translating contamination levels to annual dose

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, W.E. Jr.; Peloquin, R.A. (Pacific Northwest Lab., Richland, WA (USA))

    1990-01-01

    This document describes the generic modeling of the total effective dose equivalent (TEDE) to an individual in a population from a unit concentration of residual radioactive contamination. Radioactive contamination inside buildings and soil contamination are considered. Unit concentration TEDE factors by radionuclide, exposure pathway, and exposure scenario are calculated. Reference radiation exposure scenarios are used to derive unit concentration TEDE factors for about 200 individual radionuclides and parent-daughter mixtures. For buildings, these unit concentration factors list the annual TEDE for volume and surface contamination situations. For soil, annual TEDE factors are presented for unit concentrations of radionuclides in soil during residential use of contaminated land and the TEDE per unit total inventory for potential use of drinking water from a ground-water source. Because of the generic treatment of potentially complex ground-water systems, the annual TEDE factors for drinking water for a given inventory may only indicate when additional site data or modeling sophistication are warranted. Descriptions are provided of the models, exposure pathways, exposure scenarios, parameter values, and assumptions used. An analysis of the potential annual TEDE resulting from reference mixtures of residual radionuclides is provided to demonstrate application of the TEDE factors. 62 refs., 5 figs., 66 tabs.

  4. Residual radioactive contamination from decommissioning: Technical basis for translating contamination levels to annual dose

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Peloquin, R.A.

    1990-01-01

    This document describes the generic modeling of the total effective dose equivalent (TEDE) to an individual in a population from a unit concentration of residual radioactive contamination. Radioactive contamination inside buildings and soil contamination are considered. Unit concentration TEDE factors by radionuclide, exposure pathway, and exposure scenario are calculated. Reference radiation exposure scenarios are used to derive unit concentration TEDE factors for about 200 individual radionuclides and parent-daughter mixtures. For buildings, these unit concentration factors list the annual TEDE for volume and surface contamination situations. For soil, annual TEDE factors are presented for unit concentrations of radionuclides in soil during residential use of contaminated land and the TEDE per unit total inventory for potential use of drinking water from a ground-water source. Because of the generic treatment of potentially complex ground-water systems, the annual TEDE factors for drinking water for a given inventory may only indicate when additional site data or modeling sophistication are warranted. Descriptions are provided of the models, exposure pathways, exposure scenarios, parameter values, and assumptions used. An analysis of the potential annual TEDE resulting from reference mixtures of residual radionuclides is provided to demonstrate application of the TEDE factors. 62 refs., 5 figs., 66 tabs

  5. Community-level physiological profiles of microorganisms inhabiting soil contaminated with heavy metals

    Science.gov (United States)

    Kuźniar, Agnieszka; Banach, Artur; Stępniewska, Zofia; Frąc, Magdalena; Oszust, Karolina; Gryta, Agata; Kłos, Marta; Wolińska, Agnieszka

    2018-01-01

    The aim of the study was to assess the differences in the bacterial community physiological profiles in soils contaminated with heavy metals versus soils without metal contaminations. The study's contaminated soil originated from the surrounding area of the Szopienice non-ferrous metal smelter (Silesia Region, Poland). The control was soil unexposed to heavy metals. Metal concentration was appraised by flame atomic absorption spectrometry, whereas the the community-level physiological profile was determined with the Biolog EcoPlatesTM system. The soil microbiological activity in both sites was also assessed via dehydrogenase activity. The mean concentrations of metals (Cd and Zn) in contaminated soil samples were in a range from 147.27 to 12265.42 mg kg-1, and the heavy metal contamination brought about a situation where dehydrogenase activity inhibition was observed mostly in the soil surface layers. Our results demonstrated that there is diversity in the physiological profiles of microorganisms inhabiting contaminated and colntrol soils; therefore, for assessment purposes, these were treated as two clusters. Cluster I included colntrol soil samples in which microbial communities utilised most of the available substrates. Cluster II incorporated contaminated soil samples in which a smaller number of the tested substrates was utilised by the contained microorganisms. The physiological profiles of micro-organisms inhabiting the contaminated and the colntrol soils are distinctly different.

  6. Verification of surface contamination density standard using clearance automatic laser inspection system for objects from a nuclear power plant

    International Nuclear Information System (INIS)

    Sasaki, Michiya; Ogino, Haruyuki; Ichiji, Takeshi; Hattori, Takatoshi

    2008-01-01

    In the clearance level inspection in Japan, it is necessary to indicate that the activity level of the target object must be less than not only the clearance levels, but also the surface contamination density standards. The classification measurements for these two standards have been performed separately, and the GM survey meters based on beta-ray measurement have mainly been used for surface contamination density measurement so far. Recently the Clearance Automatic Laser Inspection System, named CLALIS, has been developed to estimate the low-level activity concentration. This system consists of 3-dimensional laser scanner for shape measurement and eight large NE102A plastic scintillation detectors for gamma-ray measurement, and it has been clarified that the CLALIS has adequate detection ability for clearance measurement of both metal scraps and concrete debris. In this study, we compared the surface contamination densities for a number of actual contaminated and non-contaminated objects generated inside from the radiation controlled area at the Kashiwazaki-Kariwa nuclear power station by using the CLALIS and the GM survey meter. As a result, since CLALIS could detect the surface contamination as well as the GM survey meter for all measurement targets, it was revealed that CLALIS can rationally achieve clearance level inspection in a single radiation measurement. The practicality of CLALIS in view of the detection limit and processing time was discussed by comparison with the usual radiation monitors for surface contamination measurement. (author)

  7. Determination of the Level of Contamination of Underground Water ...

    African Journals Online (AJOL)

    Misrak

    Determination of the Level of Contamination of. Underground Water (hand- dug well) by Organic Waste: A case Study of Ado-Ekiti, Nigeria. O.S. Omotoyinbo *. Abstract. The recent increase in urbanization has lead to increase in city population, spatial size, and generation of waste. This is a common phenomenon in Nigeria ...

  8. Evaluation of the Level of air Microbial Contamination in some ...

    African Journals Online (AJOL)

    The level of air microbial contamination in some teaching hospitals waste dump site in South Eastern Nigeria was evaluated using the standard microbiological techniques. Passive air sampling was performed using settle plates. The microbial load of the air around the hospitals waste dumpsite, showed high microbial load ...

  9. Comparative study on the level of bacteriological contamination of ...

    African Journals Online (AJOL)

    Comparative study on the level of bacteriological contamination of automatic teller machines, public toilets and public transport commercial motorcycle crash ... Conclusion: This study has revealed the ability of these public devices to serve as vehicle of transmission of microorganisms with serious health implications.

  10. Comparison of trace element contamination levels (Cu, Zn, Fe, Cd ...

    African Journals Online (AJOL)

    Comparison of trace element contamination levels (Cu, Zn, Fe, Cd and Pb) in the soft tissues of the gastropods Tympanotonus fuscatus fuscatus and Tf radula collected in the Ebrié Lagoon (Côte d'Ivoire): Evidence of the risks linked to linked to lead and.

  11. Determination of the Level of Contamination of Underground Water ...

    African Journals Online (AJOL)

    The aim of this study is to determine the level of contamination of hand-dug well which is one of the major source of water supply for the population. Water samples were taken from a total of fifteen wells at the vicinity of three major refuse dumpsite taking measurement of depth of the well, diameter, volume of water, distance ...

  12. Arsenic contamination levels in drinking water sources in mining ...

    African Journals Online (AJOL)

    Arsenic contamination in drinking water is a public health problem all over the World especially in mining areas. The study herein reported assessed the concentration levels of arsenic in some drinking water sources in the mining areas in the Lake Victoria Basin and investigated the potential for its removal by adsorption ...

  13. Comparison of trace element contamination levels (Cu, Zn, Fe, Cd ...

    African Journals Online (AJOL)

    SERVER

    2008-03-18

    Mar 18, 2008 ... A comparative survey of the levels of contamination of the two gastropods, of the Potomidae family, has been done in the lagoon Ebrié .... rinsed with demineralised water, air-dried, then maintain plugged and wrapped before being ..... Marchand M, Martin JL (1985). Détermination de la pollution chimique.

  14. Analysis of body surface radiological contamination for inbound people from Japan to China during the Fukushima nuclear accident

    International Nuclear Information System (INIS)

    Yuan Long; Ma Weidong; Lei Cuiping; Chen Huifang; Li Yuwen; Liu Ying

    2012-01-01

    Objective: To investigate the radiological contamination of body surface for inbound people from Japan to China during Fukushima nuclear accident. Methods: According to The guidance for radiological contamination management for body surface issued by Chinese Center for Disease Control and Prevention, for people evacuated from Japan, the body surface monitoring of radiological contamination was performed by the related agencies in main provinces and cities in China. The monitoring data were collected, analyzed and reported to Ministry of Health. Results: A total of 432 persons were checked. The monitoring results of 429 cases were close to the background level, while those of three persons were higher than the background level. Conclusions: In general,the detected results were as low as the background level. The radiological contamination monitoring of body surface for people from Japan could provide scientific data to relax the horror and panic among them. (authors)

  15. Explosive Contamination from Substrate Surfaces: Differences and Similarities in Contamination Techniques Using RDX and C-4

    Science.gov (United States)

    Miller, C. J.; Yoder, T. S.

    2010-06-01

    Explosive trace detection equipment has been deployed to airports for more than a decade. During this time, the need for standardized procedures and calibrated trace amounts for ensuring that the systems are operating properly and detecting the correct explosive has been apparent but a standard representative of a fingerprint has been elusive. Standards are also necessary to evaluate instrumentation in the laboratories during development and prior to deployment to determine sample throughput, probability of detection, false positive/negative rates, ease of use by operator, mechanical and/or software problems that may be encountered, and other pertinent parameters that would result in the equipment being unusable during field operations. Since many laboratories do not have access to nor are allowed to handle explosives, the equipment is tested using techniques aimed at simulating the actual explosives fingerprint. This laboratory study focused on examining the similarities and differences in three different surface contamination techniques that are used to performance test explosive trace detection equipment in an attempt to determine how effective the techniques are at replicating actual field samples and to offer scenarios where each contamination technique is applicable. The three techniques used were dry transfer deposition of standard solutions using the Transportation Security Laboratory’s (TSL) patented dry transfer techniques (US patent 6470730), direct deposition of explosive standards onto substrates, and fingerprinting of actual explosives onto substrates. RDX was deposited on the surface of one of five substrates using one of the three different deposition techniques. The process was repeated for each substrate type using each contamination technique. The substrate types used were: 50% cotton/50% polyester as found in T-shirts, 100% cotton with a smooth surface such as that found in a cotton dress shirt, 100% cotton on a rough surface such as that

  16. Characterization of sea surface chemical contamination after shipping accidents.

    Science.gov (United States)

    Guitart, Carlos; Frickers, Patricia; Horrillo-Caraballo, Jose; Law, Robin J; Readman, James W

    2008-04-01

    A contamination survey was conducted after the beaching of the stricken cargo ship MSC Napoli in Lyme Bay on the south coast of Devon (UK). A grid of 22 coastal and offshore stations was sampled to investigate the extent of spilled oil and to screen for chemical contamination, as well as to evaluate the behavior of the oil at the air-sea interface. Samples were collected from the sea surface microlayer (SML) and from subsurface waters (SSW) at each station. The fuel oil spilled (IFO 380) was also analyzed. The determination of oil-related hydrocarbons (aliphatic hydrocarbons, polycyclic aromatic hydrocarbons (PAHs), terpanes, and steranes) and the screening for other harmful chemicals on the inventory of the MSC Napoli in the seawater samples, was performed by PTV-GC/ MS using large volume injection (LVI) techniques. Screening did not reveal the presence of any harmful chemicals other than petroleum-related compounds. Results afforded investigation of oil sources and spatial distributions of total PAH concentrations and enrichments in the sea surface microlayer (SML). Rather than a single source, oil fingerprinting analyses of the samples revealed a mixture of three types of oil: heavy fuel oil, lubricating oil, and a lighter oil (probably diesel oil). Enrichment factors (EF) in the SML (EF = C(SML)/C(SSW)) were calculated and, in the vicinity of the ship, approached 2000, declining with distance away from the wreck. These factors represent approximately a 1000-fold enrichment over typical coastal total PAH enrichments in the SML and reflected a clear petrogenic origin of the contamination (as demonstrated, for example, by a Fl/Pgamma ratio water column diffusion) of the oil-related hydrocarbons in the sea surface were investigated. Essentially, near the wreck, the SML was highly enriched in oil forming a visible sheen, both disrupting the normal air-seawater exchange processes and generating a downward diffusion flux of contaminants from the SML to the SSW. This

  17. Microbial contamination detection at low levels by [125]I radiolabeling

    Science.gov (United States)

    Summers, David; Karouia, Fathi

    Contamination of mission spacecraft is an ongoing issue. A broad diversity of microorganisms have been detected in clean rooms where spacecraft are assembled. Some of which, depicted as oligotroph, are of special regard, as they are capable of colonizing inorganic surfaces like metal, and have been shown to be a concern for forward contamination of pristine celestial bodies. Currently, the NASA standard assay is the only approved assay intended for the enumeration of spores and heterotrophic microbial populations. However, culture-based microbial detection methods underestimate the viable microbial population. More recently, adenosine triphosphate (ATP) bioluminescence and limulus amebocyte lysate (LAL) assays, which employ measure-ments of selected metabolic products as a proxy of biomass, have been used successfully to circumvent the necessity of the growth of microorganisms in order to estimate the biodurdens associated with spacecraft assembly facility. However, these methods have limitation in the amount of cells that can be detected, i.e., 103 cells, and the type of microorganisms respec-tively. This work seeks to develop a new highly sensitive method for the determination of bioburdens (and the detection of microorganisms and life) that is independant of the type of organism while preserving a good turn-around time for analysis for planetary protection purposes. The assay is based on the detection of the organism's protein by labeling them by radioiodination, 125 I, of aromatic rings on tyrosine amino acids residues. Radiolabeling techniques are inherently sensitive and 125 I, in particular, benefits from a 60 day half-life, providing greater activity and signal per unit number of labels. Furthermore, microorganisms can contain over 50% of protein by dry weight. Thus, just one label per protein increases the sensitivity, compared to the ATP and LAL assays, by one and three orders of magnitude by using standard detection methods and the use of multiphoton

  18. Averaging of diffusing contaminant concentrations in atmosphere surface layer

    International Nuclear Information System (INIS)

    Ivanov, E.A.; Ramzina, T.V.

    1985-01-01

    Calculations permitting to average concentration fields of diffusing radioactive contaminant coming from the NPP exhaust stack in the atmospheric surface layer are given. Formulae of contaminant concentration field calculation are presented; it depends on the average wind direction value (THETA) for time(T) and stability of this direction (σsub(tgTHETA) or σsub(THETA)). Probability of wind direction deviation from the average value for time T is satisfactory described by the Gauss law. With instability increase in the atmosphere σ increases, when wind velocity increasing the values of σ decreases for all types of temperature gradients. Nonuniformity of σ value dependence on averaging time T is underlined, that requires accurate choice of σsub(tgTHETA) and σsub(THETA) parameters in calculations

  19. Overflow and microbiological contamination in surface and groundwaters in La Costa city (Canelones department, Uruguay)

    International Nuclear Information System (INIS)

    Marmisolle, J.; Goso Aguilar, C.

    2006-01-01

    In this paper the results of a geological risk study made during 2005 related to overflow and microbiological water contamination at Ciudad de la Costa City (Canelones department) are shown. This city has been showed a great urban growth for the last three decades. New hydrogeological studies looking forward the phreatic level and its bacteriological quality allow to know the level of the risk along 2005´s first semester. The top of the phreatic table in 40% of the studied area is below than 0.50 meter depth. The results of fourteen bacteriologic analyses in groundwater samples show extreme contamination values in faecal colliform, Pseudomona sp. and Aeruginosa content. Both surface drainage and beach water bacteriologic analyses did not show contamination values except those corresponding to Carrasco creek

  20. A decision-making process on cleanup of contaminated surface soil

    International Nuclear Information System (INIS)

    Yasuda, Hiroshi

    1996-01-01

    This study presents principles for determining derived intervention levels (DILs) for surface soil cleanup. The people concerned were divided into major three groups: residents, responsible parties, and cleanup workers; it was considered that each group has different interests. The DILs for soil cleanup were determined from the viewpoints of these three groups: safety of residence, advantages of the countermeasures, and safety of cleanup activities, respectively. An example process for determination of the DILs in accordance with the principles was also presented for a site contaminated by 137 Cs. This decision-making frame is expected to be applicable to other contaminants. (author)

  1. Estimation of contamination on plant surfaces due to deposition of radionuclides from the atmosphere

    International Nuclear Information System (INIS)

    Simmonds, J.R.

    1983-01-01

    Calculations of Normalized Specific Activity (NSA), the ratio of concentration of a contaminant per unit of vegetation to its daily rate of deposition onto the ground, have been used as a basis for determining interception factors and retention half-lives for radioactivity deposited on grain and leafy vegetables. The resulting interception factors and retention half-lives are for use in assessing contamination levels on crops at harvest during conditions of continuous deposition. The results of the study indicate that the behaviour of strontium and caesium on plant surfaces is fairly similar but that plutonium behaves in a notably different way. (author)

  2. Radiation Level Changes at RAM Package Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Opperman, Erich [Washington Savannah River Company; Hawk, Mark B [ORNL; Kapoor, Ashok [U.S. Department of Energy, Office of Packaging and Transportation; Natali, Ronald [R. B. Natali Consulting, Inc.

    2010-01-01

    This paper will explore design considerations required to meet the regulations that limit radiation level variations at external surfaces of radioactive material (RAM) packages. The radiation level requirements at package surfaces (e.g. TS-R-1 paragraphs 531 and 646) invoke not only maximum radiation levels, but also strict limits on the allowable increase in the radiation level during transport. This paper will explore the regulatory requirements by quantifying the amount of near surface movement and/or payload shifting that results in a 20% increase in the radiation level at the package surface. Typical IP-2, IP-3, Type A and Type B packaging and source geometries will be illustrated. Variations in surface radiation levels are typically the result of changes in the geometry of the surface due to an impact, puncture or crush event, or shifting and settling of radioactive contents.

  3. Bacteria contamination of touch surfaces in Polish hospital wards

    Directory of Open Access Journals (Sweden)

    Anna Różańska

    2017-08-01

    Full Text Available Background: The objective of the study has been to evaluate the pathogenic bacteria contamination of touch surfaces in hospital wards. Material and Methods: Samples were taken from frequently touched surfaces in the hospital environment in 13 units of various types. Culturing was carried out on solid blood agar and in growth broth (tryptic soy broth – TSB. Species identification was performed using the analytical profile index (API biochemical testing and confirmed with matrix assisted laser desorption ionization time-flight mass spectrometry (MALDI-TOF-MS system. Results: The total of 161 samples were taken for the study. Fifty-two of them, after 24 h of culture on a solid medium, demonstrated bacterial growth and further 60 samples had growth after prior multiplication in TSB. Overall, 69.6% of samples exhibited growth of 19 bacterial species. Pathogenic species – representing indicator organisms of efficiency of hospital cleaning – was demonstrated by 21.4% of samples. Among them Acinetobacter spp., Enterocococci spp. and Staphylococcus aureus were identified. Coagulase-negative staphylococci (CNS were predominant. The proportion of various groups of bacteria significantly varied in respective hospitals, and in various types of wards. Disturbing observation is a large proportion of resistance of isolated CNS strains as a potential reservoir of resistance genes. Conclusions: The results show that touch surfaces in hospital units are contaminated by both potentially pathogenic and pathogenic bacterial species. In connection with the reported, also in Poland, frequent omission or incorrect execution of hand hygiene by hospital staff, and probably patients, touch surfaces still constitute important reservoir of pathogenic bacteria. Improving hand hygiene compliance of health-care workers with recommendations is necessary for increasing biological safety of hospital environment. Med Pr 2017;68(3:459–467

  4. Levels of chemical contaminants in nonoccupationally exposed U. S. residents

    Energy Technology Data Exchange (ETDEWEB)

    Holleman, J.W.; Hammons, A.S.

    1978-08-01

    Data are presented on the levels of all chemical contaminants resulting from environmental pollution which have been found in human tissues including blood, urine, breast milk, and tissue samples obtained at autopsy. Most data results from specific surveys to determine health hazards. The roles of trace elements and recognition of the need to determine baseline levels of chemicals introduced into the environment are factors which have motivated surveys by individual investigators. Thus, most data on chemicals in human tissues record levels of pesticides (e.g., DDT and metabolites), levels of trace metals such as lead, cadmium, and mercury, or levels of nutritionally essential elements such as zinc, copper, manganese, and fluoride. Data available on iron and calcium are not presented as their presence in the environment is generally not considered hazardous. Data on several uncommon chemicals, such as indium and ytterbium, are included basically as items of interest and to further document their presence in healthy individuals. Baseline data were presented where available to provide perspective as to chemical levels which might be expected under conditions where exposure could be considered normal or not directly related to a pollutant source. Nearly 600 cited surveys or investigations, most of which were reported within the past decade, are listed. Ninety-four different chemical contaminants, primarily trace metals and organochlorine pesticides, are reported. It is estimated that over 75% of the data published during the past 30 years on chemical contaminants derived from environmental pollution and found in human tissue in the United States are represented in this report.

  5. Surface Contaminant Control Technologies to Improve Laser Damage Resistance of Optics

    Directory of Open Access Journals (Sweden)

    Xiaofeng Cheng

    2014-01-01

    Full Text Available The large high-power solid lasers, such as the National Ignition Facility (NIF of America and the Shenguang-III (SG-III laser facility of China, can output over 2.1 MJ laser pulse for the inertial confinement fusion (ICF experiments. Because of the enhancement of operating flux and the expansion of laser driver scale, the problem of contamination seriously influences their construction period and operation life. During irradiation by intense laser beams, the contaminants on the metallic surface of beam tubes can be transmitted to the optical surfaces and lead to damage of optical components. For the high-power solid-state laser facilities, contamination control focuses on the slab amplifiers, spatial filters, and final-optical assemblies. In this paper, an effective solution to control contaminations including the whole process of the laser driver is put forward to provide the safe operation of laser facilities, and the detailed technical methods of contamination control such as washing, cleanliness metrology, and cleanliness protecting are also introduced to reduce the probability of laser-induced damage of optics. The experimental results show that the cleanliness level of SG-III laser facility is much better to ensure that the laser facility can safely operate at high energy flux.

  6. MISR Level 2 Surface parameters V002

    Data.gov (United States)

    National Aeronautics and Space Administration — This Level 2 Land Surface product contains information on land directional reflectance properties,albedos(spectral & PAR integrated),FPAR,asssociated radiation...

  7. Skin and surface lead contamination, hygiene programs, and work practices of bridge surface preparation and painting contractors.

    Science.gov (United States)

    Virji, M Abbas; Woskie, Susan R; Pepper, Lewis D

    2009-02-01

    A 2005 regulatory review of the lead in construction standard by the Occupational Safety and Health Administration (OSHA) noted that alternative pathways of exposure can be as significant as inhalation exposure and that noncompliance with the standard pertaining to hygiene facilities and practices was the second most commonly violated section of the standard. Noncompliance with provisions of the standard and unhealthy work and hygiene practices likely increase the likelihood of take-home lead via contaminated clothing, automobiles, and skin, thus contributing to elevated blood lead levels (BLL) among construction workers and their family members. We performed a cross-sectional study of bridge painters working for small contractors in Massachusetts to investigate causes of persistent elevated BLLs and to assess lead exposures. Thirteen work sites were evaluated for a 2-week period during which surface and skin wipe samples were collected and qualitative information was obtained on personal hygiene practices, decontamination and hand wash facilities, and respiratory protection programs. Results showed lead contamination on workers' skin, respirators, personal automobiles, and the decontamination unit, indicating a significant potential for take-home lead exposure. Overall, the geometric mean (GM) skin lead levels ranged from 373 microg on workers' faces at end of shift to 814 microg on hands at break time. The overall GM lead level inside respirators was 143 microg before work and 286 microg after work. Lead contamination was also present inside workers' personal vehicles as well as on surfaces inside the clean side of the decontamination unit. Review of the respiratory protection programs, work site decontamination and hand wash facilities, and personal hygiene practices indicated that these factors had significant impact on skin and surface contamination levels and identified significant opportunities for improving work site facilities and personal practices

  8. Present level of contaminants in the Romanian Black Sea sector

    International Nuclear Information System (INIS)

    Bologa, A.S.; Apas, M.; Cociasu, A.; Cuingioglu, E.; Patrascu, V.; Pecheanu, I.; Piescu, V.; Popa, L.

    1999-01-01

    The assessment of environmental quality in the Romanian Black Sea sector is being constantly made by the Romanian Marine Research Institute (RMRI) within the National Integrated Monitoring System. The contamination of the marine environment is expressed by considering four chemical and a biological parameter: nutrients (N-NO 2 , N-NO 3 , N-NH 4 , P-PO 4 , organic P, Si-SiO 4 ), heavy metals (Mn, Fe, Cu, Cd, Pb), artificial radionuclides ( 90 Sr, 137 Cs), total hydrocarbons, parasite and saprophyte fungi in sediments, sea water and/or biota. Present levels of contaminants are discussed as to their historical evolution during the last few years or decades. Inorganic N and P concentrations still exceed three to five times those before eutrophication started to intensify in the early '70s. Practical uses of results by national and regional authorities are discussed. (author)

  9. Detection of aflatoxin and surface mould contaminated figs by using Fourier transform near-infrared reflectance spectroscopy.

    Science.gov (United States)

    Durmuş, Efkan; Güneş, Ali; Kalkan, Habil

    2017-01-01

    Aflatoxins are toxic metabolites that are mainly produced by members of the Aspergillus section Flavi on many agricultural products. Certain agricultural products such as figs are known to be high risk products for aflatoxin contamination. Aflatoxin contaminated figs may show a bright greenish yellow fluorescence (BGYF) under ultraviolet (UV) light at a wavelength of 365 nm. Traditionally, BGYF positive figs are manually selected by workers. However, manual selection depends on the expertise level of the workers and it may cause them skin-related health problems due to UV radiation. In this study, we propose a non-invasive approach to detect aflatoxin and surface mould contaminated figs by using Fourier transform near-infrared (FT-NIR) reflectance spectroscopy. A classification accuracy of 100% is achieved for classifying the figs into aflatoxin contaminated/uncontaminated and surface mould contaminated/uncontaminated categories. In addition, a strong correlation has been found between aflatoxin and surface mould. Combined with pattern classification methods, the NIR spectroscopy can be used to detect aflatoxin contaminated figs non-invasively. Furthermore, a positive correlation between surface mould and aflatoxin contamination leads to a promising alternative indicator for the detection of aflatoxin-contaminated figs. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  10. Contaminants of emerging concern in surface waters in Barbados, West Indies.

    Science.gov (United States)

    Edwards, Quincy A; Kulikov, Sergei M; Garner-O'Neale, Leah D; Metcalfe, Chris D; Sultana, Tamanna

    2017-11-14

    Contaminants of emerging concern (CECs), including pharmaceuticals, artificial sweeteners, steroid hormones, and current-use pesticides have been detected in surface waters around the world, but to date, there have been no reports in the peer-reviewed literature on the levels of these classes of contaminants in freshwater resources in the Caribbean region. In the present study, multi-residue solid phase extraction (SPE) and liquid chromatography with tandem mass spectroscopy (LC-MS/MS) were used to analyze grab samples of surface waters collected from five different watersheds in Barbados, West Indies. The artificial sweeteners (AS), acesulfame, cyclamate, saccharin, and sucralose were widely detected in the watersheds, indicating contamination from domestic wastewater, and the concentrations of these chemical tracers in water were correlated with the concentrations of the non-prescription pharmaceutical, ibuprofen (R 2 values of 0.4-0.6). Surprisingly, the concentrations of another chemical tracer of domestic wastewater, caffeine were not correlated with ibuprofen or AS concentrations. Several other prescription pharmaceuticals and the steroid hormones, estrone and androstenedione, were detected in selected watersheds at low ng/L concentrations. The fungicide, chlorothalonil was widely detected in surface waters at low (contamination of water resources by pharmaceuticals.

  11. Bond strength of resin-resin interfaces contaminated with saliva and submitted to different surface treatments

    OpenAIRE

    Furuse, Adilson Yoshio; Cunha, Leonardo Fernandes da; Benetti, Ana Raquel; Mondelli, José

    2007-01-01

    The purpose of this study was to investigate the effect of different surface treatments on shear bond strength of saliva-contaminated resin-resin interfaces. Flat resin surfaces were fabricated. In the control group, no contamination or surface treatment was performed. The resin surfaces of the experimental groups were contaminated with saliva and air-dried, and then submitted to: (G1) rinsing with water and drying; (G2) application of an adhesive system; (G3) rinsing and drying, abrasion wit...

  12. Effect of Surface Contaminants Remained on the Blasted Surface on Epoxy Coating Performance and Corrosion Resistance

    International Nuclear Information System (INIS)

    Baek, Kwang Ki; Park, Chung Seo; Kim, Ki Hong; Chung, Mong Kyu; Park, Jin Hwan

    2006-01-01

    One of the critical issues in the coating specification is the allowable limit of surface contaminant(s) - such as soluble salt(s), grit dust, and rust - after grit blasting. Yet, there is no universally accepted data supporting the relationship between the long-term coating performance and the amount of various surface contaminants allowed after grit blasting. In this study, it was attempted to prepare epoxy coatings applied on grit-blasted steel substrate dosed with controlled amount of surface contaminants - such as soluble salt(s), grit dust, and rust. Then, coating samples were subjected to 4,200 hours of cyclic test(NORSOK M-501), which were then evaluated in terms of resistance to rust creepage, blistering, chalking, rusting, cracking and adhesion strength. Additional investigations on the possible damage at the paint/steel interface were carried out using an Electrochemical Impedance Spectroscopy(EIS) and observations of under-film-corrosion. Test results suggested that the current industrial specifications were well matched with the allowable degree of rust, whereas the allowable amount of soluble salt and grit dust after grit blasting showed a certain deviation from the specifications currently employed for fabrication of marine vessels and offshore facilities

  13. Determination of platinum surface contamination in veterinary and human oncology centres using inductively coupled plasma mass spectrometry

    NARCIS (Netherlands)

    Janssens, T.; Brouwers, E. E M; de Vos, J. P.; de Vries, N.; Schellens, J. H M; Beijnen, J. H.

    2015-01-01

    The objective of this study was to determine the surface contamination with platinum-containing antineoplastic drugs in veterinary and human oncology centres. Inductively coupled plasma mass spectrometry was used to measure platinum levels in surface samples. In veterinary and human oncology

  14. Listeria monocytogenes in Fresh Produce: Outbreaks, Prevalence and Contamination Levels

    Directory of Open Access Journals (Sweden)

    Qi Zhu

    2017-03-01

    Full Text Available Listeria monocytogenes, a member of the genus Listeria, is widely distributed in agricultural environments, such as soil, manure and water. This organism is a recognized foodborne pathogenic bacterium that causes many diseases, from mild gastroenteritis to severe blood and/or central nervous system infections, as well as abortion in pregnant women. Generally, processed ready-to-eat and cold-stored meat and dairy products are considered high-risk foods for L. monocytogenes infections that cause human illness (listeriosis. However, recently, several listeriosis outbreaks have been linked to fresh produce contamination around the world. Additionally, many studies have detected L. monocytogenes in fresh produce samples and even in some minimally processed vegetables. Thus L. monocytogenes may contaminate fresh produce if present in the growing environment (soil and water. Prevention of biofilm formation is an important control measure to reduce the prevalence and survival of L. monocytogenes in growing environments and on fresh produce. This article specifically focuses on fresh produce–associated listeriosis outbreaks, prevalence in growing environments, contamination levels of fresh produce, and associated fresh produce safety challenges.

  15. Potential effects of groundwater and surface water contamination in an urban area, Qus City, Upper Egypt

    Science.gov (United States)

    Abdalla, Fathy; Khalil, Ramadan

    2018-05-01

    The potential effects of anthropogenic activities, in particular, unsafe sewage disposal practices, on shallow groundwater in an unconfined aquifer and on surface water were evaluated within an urban area by the use of hydrogeological, hydrochemical, and bacteriological analyses. Physicochemical and bacteriological data was obtained from forty-five sampling points based on33 groundwater samples from variable depths and 12 surface water samples. The pollution sources are related to raw sewage and wastewater discharges, agricultural runoff, and wastewater from the nearby Paper Factory. Out of the 33 groundwater samples studied, 17 had significant concentrations of NO3-, Cl- and SO42-, and high bacteria counts. Most of the water samples from the wells contained high Fe, Mn, Pb, Zn, Cd, and Cr. The majority of surface water samples presented high NO3- concentrations and high bacteria counts. A scatter plot of HCO3- versus Ca indicates that 58% of the surface water samples fall within the extreme contamination zone, while the others are within the mixing zone; whereas 94% of groundwater samples showed evidence of mixing between groundwater and wastewater. The bacteriological assessment showed that all measured surface and groundwater samples contained Escherichia coli and total coliform bacteria. A risk map delineated four classes of contamination, namely, those sampling points with high (39.3%), moderate (36.3%), low (13.3%), and very low (11.1%) levels of contamination. Most of the highest pollution points were in the middle part of the urban area, which suffers from unmanaged sewage and industrial effluents. Overall, the results demonstrate that surface and groundwater in Qus City are at high risk of contamination by wastewater since the water table is shallow and there is a lack of a formal sanitation network infrastructure. The product risk map is a useful tool for prioritizing zones that require immediate mitigation and monitoring.

  16. Decontamination of Vibrio parahaemolyticus in fish by washing with hygienic seawater and impacts of the high level contamination in the gills and viscera.

    Science.gov (United States)

    Hara-Kudo, Yukiko; Kumagai, Susumu; Konuma, Hirotaka; Miwa, Norinaga; Masuda, Takashi; Ozawa, Kazuhiro; Nishina, Tokuhiro

    2013-01-01

    The effect of washing in Vibrio parahaemolyticus contaminated and hygienic seawater on fish, and the frequency and level of natural V. parahaemolyticus contamination in fish were investigated. In the first experiment, live horse mackerel was experimentally kept in seawater artificially contaminated with V. parahaemolyticus. After washing in contaminated and hygienic seawater, the contamination in fish was quantitatively analyzed. Washing fish in the seawater contaminated with V. parahaemolyticus increases the contamination level on the surface and in the gills of the fish. Washing in hygienic seawater was effective in reducing the contamination in fish and cutting board surfaces, but not in the gills or viscera. In the second experiment, natural V. parahaemolyticus contamination in various fish caught by us was analyzed. V. parahaemolyticus was detected in 6 of 28 gill samples and 10 of 28 viscera samples of naturally contaminated fish. The means of V. parahaemolyticus level on gills were 3.3 and 3.9 log cfu/g, and those in viscera were 2.6 and 4.4 log cfu/g by culture method and a real-time PCR assay, respectively. These results indicate that the gills and viscera are able to spread the pathogens to fish meat as well as fish surface contamination by washing in the contaminated seawater. Washing with hygienic seawater and control of contamination from gills and viscera are critically important to prevent V. parahaemolyticus infections.

  17. A review and outlook for the removal of radon-generated Po-210 surface contamination

    Science.gov (United States)

    Guiseppe, V. E.; Christofferson, C. D.; Hair, K. R.; Adams, F. M.

    2018-01-01

    The next generation low-background detectors operating deep underground aim for unprecedented low levels of radioactive backgrounds. The deposition and presence of radon progeny on detector surfaces is an added source of energetic background events. In addition to limiting the detector material's radon exposure in order to reduce potential surface backgrounds, it is just as important to clean surfaces to remove inevitable contamination. Such studies of radon progeny removal have generally found that a form of etching is effective at removing some of the progeny (Bi and Pb), however more aggressive techniques, including electropolishing, have been shown to effectively remove the Po atoms. In the absence of an aggressive etch, a significant fraction of the Po atoms are believed to either remain behind within the surface or redeposit from the etching solution back onto the surface. We explore the chemical nature of the aqueous Po ions and the effect of the oxidation state of Po to maximize the Po ions remaining in the etching solution of contaminated Cu surfaces. We present a review of the previous studies of surface radon progeny removal and our findings on the role of oxidizing agents and a cell potential in the preparation of a clean etching technique.

  18. Emerging contaminants in surface waters in China—a short review

    International Nuclear Information System (INIS)

    Yang, Guang; Zhang, Guangming; Fan, Maohong

    2014-01-01

    Emerging contaminants (ECs) have drawn attention to many countries due to their persistent input and potential threat to human health and the environment. This article reviews the current contamination sources and their status for surface waters in China. The contamination levels of ECs in surface waters are in the range ng L −1 to μg L −1 in China, apparently about the same as the situation in other countries. ECs enter surface water via runoff, drainage, rainfall, and wastewater treatment effluent. The frequency of occurrence of ECs increased rapidly from 2006 to 2011; a significant reason is the production and consumption of pharmaceuticals and personal care products. As for the distribution of EC pollution in China, the frequency of occurrence of ECs in eastern regions is higher than in western regions. A majority of EC studies have focused on surface waters of the Haihe River and Pearl River watersheds due to their highly developed industries and intense human activity. Legislative and administrative regulation of ECs is lacking in China. To remove ECs, a number of technologies, such as absorption by activated carbon, membrane filtration technology, and advanced oxidation processes, have been researched. (letter)

  19. Emerging contaminants in surface waters in China—a short review

    Science.gov (United States)

    Yang, Guang; Fan, Maohong; Zhang, Guangming

    2014-07-01

    Emerging contaminants (ECs) have drawn attention to many countries due to their persistent input and potential threat to human health and the environment. This article reviews the current contamination sources and their status for surface waters in China. The contamination levels of ECs in surface waters are in the range ng L-1 to μg L-1 in China, apparently about the same as the situation in other countries. ECs enter surface water via runoff, drainage, rainfall, and wastewater treatment effluent. The frequency of occurrence of ECs increased rapidly from 2006 to 2011; a significant reason is the production and consumption of pharmaceuticals and personal care products. As for the distribution of EC pollution in China, the frequency of occurrence of ECs in eastern regions is higher than in western regions. A majority of EC studies have focused on surface waters of the Haihe River and Pearl River watersheds due to their highly developed industries and intense human activity. Legislative and administrative regulation of ECs is lacking in China. To remove ECs, a number of technologies, such as absorption by activated carbon, membrane filtration technology, and advanced oxidation processes, have been researched.

  20. Trench 'bathtubbing' and surface plutonium contamination at a legacy radioactive waste site.

    Science.gov (United States)

    Payne, Timothy E; Harrison, Jennifer J; Hughes, Catherine E; Johansen, Mathew P; Thiruvoth, Sangeeth; Wilsher, Kerry L; Cendón, Dioni I; Hankin, Stuart I; Rowling, Brett; Zawadzki, Atun

    2013-01-01

    Radioactive waste containing a few grams of plutonium (Pu) was disposed between 1960 and 1968 in trenches at the Little Forest Burial Ground (LFBG), near Sydney, Australia. A water sampling point installed in a former trench has enabled the radionuclide content of trench water and the response of the water level to rainfall to be studied. The trench water contains readily measurable Pu activity (~12 Bq/L of (239+240)Pu in 0.45 μm-filtered water), and there is an associated contamination of Pu in surface soils. The highest (239+240)Pu soil activity was 829 Bq/kg in a shallow sample (0-1 cm depth) near the trench sampling point. Away from the trenches, the elevated concentrations of Pu in surface soils extend for tens of meters down-slope. The broader contamination may be partly attributable to dispersion events in the first decade after disposal, after which a layer of soil was added above the trenched area. Since this time, further Pu contamination has occurred near the trench-sampler within this added layer. The water level in the trench-sampler responds quickly to rainfall and intermittently reaches the surface, hence the Pu dispersion is attributed to saturation and overflow of the trenches during extreme rainfall events, referred to as the 'bathtub' effect.

  1. Treatment options for low-level radiologically contaminated ORNL filtercake

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hom-Ti [Oak Ridge Associated Universities, Inc., TN (United States); Bostick, W.D. [Oak Ridge K-25 Site, TN (United States)

    1996-04-01

    Water softening sludge (>4000 stored low level contaminated drums; 600 drums per year) generated by the ORNL Process Waste Treatment Plant must be treated, stabilized, and placed in safe storage/disposal. The sludge is primarily CaCO{sub 3} and is contaminated by low levels of {sup 90}Sr and {sup 137}Cs. In this study, microwave sintering and calcination were evaluated for treating the sludge. The microwave melting experiments showed promise: volume reductions were significant (3-5X), and the waste form was durable with glass additives (LiOH, fly ash). A commercial vendor using surrogate has demonstrated a melt mineralization process that yields a dense monolithic waste form with a volume reduction factor (VR) of 7.7. Calcination of the sludge at 850-900 C yielded a VR of 2.5. Compaction at 4500 psi increased the VR to 4.2, but the compressed form is not dimensionally stable. Addition of paraffin helped consolidate fines and yielded a VR of 3.5. In conclusion, microwave melting or another form of vitrification is likely to be the best method; however for immediate implementation, the calculation/compaction/waxing process is viable.

  2. Filtration of contaminated suspended solids for the treatment of surface water.

    Science.gov (United States)

    Mulligan, Catherine N; Davarpanah, Neginmalak; Fukue, Masaharu; Inoue, Tomohiro

    2009-02-01

    As few technologies exist worldwide for the treatment of contaminated surface water, a new approach is currently under development consisting of an in situ water treatment system based on a floating filtration process for adsorbed contaminants such as heavy metals. Laboratory filtration tests were performed for the removal of contaminated suspended solids (SS) from surface water. SS, chemical oxygen demand (COD), and organic carbon (OC) were monitored. Of the four filters (two non-woven geotextiles, a woven geotextile and a sand filter) evaluated, filter 1 (a non-woven geotextile) was the most effective for removal % of the total suspended solids. The results demonstrated excellent efficiency by filter No. 1, for reducing turbidity by 93-98%, as well as SS by up to 98.9% and COD by 65-71% for three sites with initial turbidities of 70, 20, and 120 NTU, respectively. The level of heavy metal removal was 98.9% due the heavy metal content of the suspended solids (60 mg kg(-1) of Cu, 90 mg kg (-1) of Ni, 130 mg kg(-1) of Zn, 200 mg kg(-1) of Cr, and 80 mg kg(-1) of Pb). The development of this technology could potentially protect the public and aquatic plants and animals from dangerous contaminants such as heavy metals adsorbed onto the suspended solids.

  3. Surface Contamination Monitor and Survey Information Management System

    International Nuclear Information System (INIS)

    1998-02-01

    Shonka Research Associates, Inc.'s (SRA) Surface Contamination Monitor and Survey Information management System (SCM/SIMS) is designed to perform alpha and beta radiation surveys of floors and surfaces and document the measured data. The SRA-SCM/SIMS technology can be applied to routine operational surveys, characterization surveys, and free release and site closure surveys. Any large nuclear site can make use of this technology. This report describes a demonstration of the SRA-SCM/SIMS technology. This demonstration is part of the chicago Pile-5 (CP-5) Large-Scale Demonstration Project (LSDP) sponsored by the US Department of Energy (DOE), Office of Science and Technology (ST), Deactivation and Decommissioning Focus Area (DDFA). The objective of the LSDP is to select and demonstrate potentially beneficial technologies at the Argonne National Laboratory-East's (ANL) CP-5 Research Reactor Facility. The purpose of the LSDP is to demonstrate that by using innovative and improved deactivation and decommissioning (D and D) technologies from various sources, significant benefits can be achieved when compared to baseline D and D technologies

  4. Surface Contamination Monitor and Survey Information Management System

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-02-01

    Shonka Research Associates, Inc.`s (SRA) Surface Contamination Monitor and Survey Information management System (SCM/SIMS) is designed to perform alpha and beta radiation surveys of floors and surfaces and document the measured data. The SRA-SCM/SIMS technology can be applied to routine operational surveys, characterization surveys, and free release and site closure surveys. Any large nuclear site can make use of this technology. This report describes a demonstration of the SRA-SCM/SIMS technology. This demonstration is part of the chicago Pile-5 (CP-5) Large-Scale Demonstration Project (LSDP) sponsored by the US Department of Energy (DOE), Office of Science and Technology (ST), Deactivation and Decommissioning Focus Area (DDFA). The objective of the LSDP is to select and demonstrate potentially beneficial technologies at the Argonne National Laboratory-East`s (ANL) CP-5 Research Reactor Facility. The purpose of the LSDP is to demonstrate that by using innovative and improved deactivation and decommissioning (D and D) technologies from various sources, significant benefits can be achieved when compared to baseline D and D technologies.

  5. evaluation of metal contaminants of surface water sources in an ...

    African Journals Online (AJOL)

    SAMSUNG

    This study evaluated the potential health risks associated with domestic use of surface water from an active Pb-Zn mine pit, compared to a ... about the health and environmental risks associated with high levels of metal ... S. O. Ngele, Department of Industrial Chemistry, Ebonyi State University Abakaliki, Nigeria. E. J. Itumoh ...

  6. Volume reduction of low-level contaminated metal waste by melting: selection of method and conceptual plan

    International Nuclear Information System (INIS)

    Copeland, G.L.; Heestand, R.L.; Mateer, R.S.

    1978-06-01

    A review of the literature and prior experience led to selection of induction melting as the most promising method for volume reduction of low-level transuranic contaminated metal waste. The literature indicates that melting with the appropriate slags significantly lowers the total contamination level of the metals by preferentially concentrating contaminants in the smaller volume of slag. Surface contamination not removed to the slag is diluted in the ingot and is contained uniformly in the metal. This dilution and decontamination offers the potential of lower cost disposal such as shallow burial rather than placement in a national repository. A processing plan is proposed as a model for economic analysis of the collection and volume reduction of contaminated metals. Further development is required to demonstrate feasibility of the plan

  7. 40 CFR 141.11 - Maximum contaminant levels for inorganic chemicals.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Maximum contaminant levels for inorganic chemicals. 141.11 Section 141.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... § 141.11 Maximum contaminant levels for inorganic chemicals. (a) The maximum contaminant level for...

  8. Increased hand washing reduces influenza virus surface contamination in Bangkok households, 2009-2010.

    Science.gov (United States)

    Levy, Jens W; Suntarattiwong, Piyarat; Simmerman, James M; Jarman, Richard G; Johnson, Kara; Olsen, Sonja J; Chotpitayasunondh, Tawee

    2014-01-01

    Within a hand-washing clinical trial, we evaluated factors associated with fomite contamination in households with an influenza-infected child. Influenza virus RNA contamination was higher in households with low absolute humidity and in control households, suggesting that hand washing reduces surface contamination. © 2013 The Authors. Influenza and Other Respiratory Viruses Published by John Wiley & Sons Ltd.

  9. Increased hand washing reduces influenza virus surface contamination in Bangkok households, 2009–2010

    Science.gov (United States)

    Levy, Jens W; Suntarattiwong, Piyarat; Simmerman, James M; Jarman, Richard G; Johnson, Kara; Olsen, Sonja J; Chotpitayasunondh, Tawee

    2014-01-01

    Within a hand-washing clinical trial, we evaluated factors associated with fomite contamination in households with an influenza-infected child. Influenza virus RNA contamination was higher in households with low absolute humidity and in control households, suggesting that hand washing reduces surface contamination. PMID:24373290

  10. Position-sensitive radiation monitoring (surface contamination monitor). Innovative technology summary report

    International Nuclear Information System (INIS)

    1999-06-01

    The Shonka Research Associates, Inc. Position-Sensitive Radiation Monitor both detects surface radiation and prepares electronic survey map/survey report of surveyed area automatically. The electronically recorded map can be downloaded to a personal computer for review and a map/report can be generated for inclusion in work packages. Switching from beta-gamma detection to alpha detection is relatively simple and entails moving a switch position to alpha and adjusting the voltage level to an alpha detection level. No field calibration is required when switching from beta-gamma to alpha detection. The system can be used for free-release surveys because it meets the federal detection level sensitivity limits requires for surface survey instrumentation. This technology is superior to traditionally-used floor contamination monitor (FCM) and hand-held survey instrumentation because it can precisely register locations of radioactivity and accurately correlate contamination levels to specific locations. Additionally, it can collect and store continuous radiological data in database format, which can be used to produce real-time imagery as well as automated graphics of survey data. Its flexible design can accommodate a variety of detectors. The cost of the innovative technology is 13% to 57% lower than traditional methods. This technology is suited for radiological surveys of flat surfaces at US Department of Energy (DOE) nuclear facility decontamination and decommissioning (D and D) sites or similar public or commercial sites

  11. Levels and trends of radioactive contaminants in the Greenland environment

    DEFF Research Database (Denmark)

    Dahlgaard, H.; Eriksson, M.; Nielsen, S.P.

    2004-01-01

    . Reindeer and lamb contain the largest observed (137)Cs concentrations in the terrestrial environment-up to 80 Bq kg(-1) fresh weight have been observed in reindeer. Due to special environmental conditions, (137)Cs is transferred to landlocked Arctic char with extremely high efficiency in South Greenland......Levels of radioactive contaminants in various Greenland environments have been assessed during 1999-2001. The source of (137)Cs (90)Sr and (239,240)Pu in terrestrial and fresh water environments is mainly global fallout. In addition, the Chernobyl accident gave a small contribution of (137)Cs...... leading to concentrations up to 100 Bq kg(-1) fresh weight. In these cases very long ecological half-lives are seen. Concentrations of (99)Tc, (137)Cs and (90)Sr in seawater and in marine biota decrease in the order NorthEast Greenland and the coastal East Greenland current> South-West Greenland> Central...

  12. Limits determination of microbial contamination present on surfaces from a pharmaceutical microbiology district reference laboratory

    Directory of Open Access Journals (Sweden)

    Natalia Charry

    2016-06-01

    Full Text Available Context: The bioburden present on the pharmaceutical microbiology laboratory’s surfaces, may increase the risk of cross-contamination when analytical tests are being carried out; periodic monitoring allows to set limits that reduce the risk. Aims: To determinate the limits of bioburden present on seven surfaces of the pharmaceutical microbiology laboratory, after the cleaning and disinfection process. Methods: The swabbing method was used for sampling. With a 25 cm2 stencil and a sterile swab, a sample was taken, passing the swab over five points of every surface chosen. A total aerobic microbial count and a total yeast and mold count was done. Finally, the average and the standard deviation of the counts was obtained. Results: The average from the counts obtained on each surface selected for the study, were below the recommended limits by international entities like the World Health Organization and the European Union, between others; also, the results generated in this study, allow to classify the biosafety cabinet as an ISO 5 area and the other areas as ISO 7. Conclusions: Bioburden levels on the tested surfaces are considered low, reducing the risk of cross-contamination, which could have a negative impact on laboratory’s activities. Also, it follows that disinfectant concentration used, is effectively.

  13. Long-term consequences of radioactive surface contamination in agriculture

    International Nuclear Information System (INIS)

    Haak, E.

    1983-01-01

    Based on agricultural statistics of crop and animal produce for 1981, and on transfer coefficients, as obtained from long-term Swedish field experiments and the literature, the transfer of 137-Cs and 90-Sr within the chain: Soil crop - food, and the chain: soil - crop - animal - food was estimated for an average km 2 of farming land in nine different countries, with the assumption that 1 TBq had been deposited at a single event and remained near the surface of grass fields and/or had been incorporated into the plough layer of arable soils prior to reuse after a nuclear accident. Calculations are given in detail, and the results are discussed as regards the situation of unchanged farming and soil management practices. The transfer of the two nuclides from soil to different vectors within the two chains was shown to vary among the countries, due to differences in soil, use of pasture and an arable land, as well as current plant and animal produce. The transfer of nuclides from fodder to food is effectively reduced by the animal link and more so for strontium than for cesium. The contamination recirculates back to the soil. The effect of corrective measures to reduce nuclide transfer from soil to food, by changed fertilizer and soil management practices as well as changes from current farming systems to pig or beef cattle

  14. Literature review of cask exterior surface contamination with application to a nuclear repository

    International Nuclear Information System (INIS)

    Adams, K.G.

    1990-04-01

    The characteristics of transportation cask surface contamination and the ''weeping'' phenomenon are reviewed. In addition, literature that pertains to the possible impact of surface contamination on repository operations is reviewed. This report consists of commentary on and rather extensive excerpts from the published literature on cask surface contamination that may have a bearing on repository risk assessment. In addition, estimates are made of the quantity of contamination that might be present on a cask. These estimates are used to calculate the direct exposure rates to personnel located at several distances from the cask. 15 refs., 15 tabs

  15. Surface-to-surface registration using level sets

    DEFF Research Database (Denmark)

    Hansen, Mads Fogtmann; Erbou, Søren G.; Vester-Christensen, Martin

    2007-01-01

    problem can be approximated by the image registration (IR) problem of the signed distance maps (SDMs) of the surfaces confined to some narrow band. By shrinking the narrow bands around the zero level sets the solution to the IR problem converges towards the S2SR problem. It is our hypothesis...... that this approach is more robust and less prone to fall into local minima than ordinary surface-to-surface registration. The IR problem is solved using the inverse compositional algorithm. In this paper, a set of 40 pelvic bones of Duroc pigs are registered to each other w.r.t. the Euclidean transformation...

  16. The organic contamination level based on the total soil mass is not a proper index of the soil contamination intensity

    Science.gov (United States)

    Hung, H.-W.; Daniel, Sheng G.; Lin, T.-F.; Su, Y.; Chiou, C.T.

    2009-01-01

    Concentrations of organic contaminants in common productive soils based on the total soil mass give a misleading account of actual contamination effects. This is attributed to the fact that productive soils are essentially water-saturated, with the result that the soil uptake of organic compounds occurs principally by partition into the soil organic matter (SOM). This report illustrates that the soil contamination intensity of a compound is governed by the concentration in the SOM (Com) rather than by the concentration in whole soil (Cs). Supporting data consist of the measured levels and toxicities of many pesticides in soils of widely differing SOM contents and the related levels in in-situ crops that defy explanation by the Cs values. This SOM-based index is timely needed for evaluating the contamination effects of food crops grown in different soils and for establishing a dependable priority ranking for intended remediation of numerous contamination sites.

  17. Accuracy Analysis of a Robotic Radionuclide Inspection and Mapping System for Surface Contamination

    International Nuclear Information System (INIS)

    Mauer, Georg F.; Kawa, Chris

    2008-01-01

    The mapping of localized regions of radionuclide contamination in a building can be a time consuming and costly task. Humans moving hand-held radiation detectors over the target areas are subject to fatigue. A contamination map based on manual surveys can contain significant operator-induced inaccuracies. A Fanuc M16i light industrial robot has been configured for installation on a mobile aerial work platform, such as a tall forklift. When positioned in front of a wall or floor surface, the robot can map the radiation levels over a surface area of up to 3 m by 3 m. The robot's end effector is a commercial alpha-beta radiation sensor, augmented with range and collision avoidance sensors to ensure operational safety as well as to maintain a constant gap between surface and radiation sensors. The accuracy and repeatability of the robotically conducted contamination surveys is directly influenced by the sensors and other hardware employed. This paper presents an in-depth analysis of various non-contact sensors for gap measurement, and the means to compensate for predicted systematic errors that arise during the area survey scans. The range sensor should maintain a constant gap between the radiation counter and the surface being inspected. The inspection robot scans the wall surface horizontally, moving down at predefined vertical intervals after each scan in a meandering pattern. A number of non-contact range sensors can be employed for the measurement of the gap between the robot end effector and the wall. The nominal gap width was specified as 10 mm, with variations during a single scan not to exceed ± 2 mm. Unfinished masonry or concrete walls typically exhibit irregularities, such as holes, gaps, or indentations in mortar joints. These irregularities can be sufficiently large to indicate a change of the wall contour. The responses of different sensor types to the wall irregularities vary, depending on their underlying principles of operation. We explored

  18. Assessment of Surface Water Contamination from Coalbed Methane Fracturing-Derived Volatile Contaminants in Sullivan County, Indiana, USA.

    Science.gov (United States)

    Meszaros, Nicholas; Subedi, Bikram; Stamets, Tristan; Shifa, Naima

    2017-09-01

    There is a growing concern over the contamination of surface water and the associated environmental and public health consequences from the recent proliferation of hydraulic fracturing in the USA. Petroleum hydrocarbon-derived contaminants of concern [benzene, toluene, ethylbenzene, and xylenes (BTEX)] and various dissolved cations and anions were spatially determined in surface waters around 15 coalbed methane fracking wells in Sullivan County, IN, USA. At least one BTEX compound was detected in 69% of sampling sites (n = 13) and 23% of sampling sites were found to be contaminated with all of the BTEX compounds. Toluene was the most common BTEX compound detected across all sampling sites, both upstream and downstream from coalbed methane fracking wells. The average concentration of toluene at a reservoir and its outlet nearby the fracking wells was ~2× higher than other downstream sites. However, one of the upstream sites was found to be contaminated with BTEX at similar concentrations as in a reservoir site nearby the fracking well. Calcium (~60 ppm) and sulfates (~175 ppm) were the dominant cations and anions, respectively, in surface water around the fracking sites. This study represents the first report of BTEX contamination in surface water from coalbed methane hydraulic fracturing wells.

  19. Level of Campylobacter jejuni from naturally contaminated chicken liver and chicken legs in various task: a cross contamination study

    Directory of Open Access Journals (Sweden)

    New, C.Y.

    2017-03-01

    Full Text Available Cross contamination is one of the most important contributing factors in foodborne illness originating in household environments. The objective of this research was to determine the transfer between naturally contaminated chicken liver and leg to cutting board, hand glove, knife and cucumber, during slicing. The microorganism tested was Campylobacter jejuni and the results showed that the pathogen transferred to all utensils, at different transfer rate, despite the low level of the naturally contaminating pathogen. With unknown concentration bacteria in the naturally contaminated samples, a proportion of the utensils were still contaminated with C. jejuni and not surprisingly, when the sample were contaminated with higher concentrations of the pathogen, a higher proportion of the utensils had detectable C. jejuni cells present, though in many cases cross contamination seems to be a random event. Transfer of the naturally contaminating C. jejuni from the chicken liver and leg to the utensils were <3.0 to 9.2 MPN/g and <3.0 to 3.0 MPN/g, respectively. The results of this study highlighted the potential for cross contamination of food borne pathogens in the kitchen environment.

  20. A Review of Removable Surface Contamination on Radioactive Materials Transportation Containers

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, Jr, W. E.; Watson, E. C.; Murphy, D. W.; Harrer, B. J.; Harty, R.; Aldrich, J. M.

    1981-05-01

    This report contains the results of a study sponsored by the U.S. Nuclear Regulatory Commission (NRC) of removable surface contamination on radioactive materials transportation containers. The purpose of the study is to provide information to the NRC during their review of existing regulations. Data was obtained from both industry and literature on three major topics: 1) radiation doses, 2) economic costs, and 3) contamination frequencies. Containers for four categories of radioactive materials are considered including radiopharmaceuticals, industrial sources, nuclear fuel cycle materials, and low-level radioactive waste. Assumptions made in this study use current information to obtain realistic yet conservative estimates of radiation dose and economic costs. Collective and individual radiation doses are presented for each container category on a per container basis. Total doses, to workers and the public, are also presented for spent fuel cask and low-level waste drum decontamination. Estimates of the additional economic costs incurred by lowering current limits by factors of 10 and 100 are presented. Current contamination levels for each category of container are estimated from the data collected. The information contained in this report is designed to be useful to the NRC in preparing their recommendations for new regulations.

  1. A risk-informed basis for establishing non-fixed surface contamination limits for spent fuel transportation casks

    International Nuclear Information System (INIS)

    Rawl, R.R.; Eckerman, K.F.; Bogard, J.S.; Cook, J.R.

    2004-01-01

    The current limits for non-fixed contamination on packages used to transport radioactive materials were introduced in the 1961 edition of the International Atomic Energy Agency (IAEA) transport regulations and were based on radiation protection guidance and practices in use at that time. The limits were based on exposure scenarios leading to intakes of radionuclides by inhalation and external irradiation of the hands. These considerations are collectively referred to as the Fairbairn model. Although formulated over 40 years ago, the model remains unchanged and is still the basis of current regulatory-derived limits on package non-fixed surface contamination. There can also be doses that while not resulting directly from the contamination, are strongly influenced by and attributable to transport regulatory requirements for contamination control. For example, actions necessary to comply with the current derived limits for light-water-reactor (LWR) spent nuclear fuel (SNF) casks can result in significant external doses to workers. This is due to the relatively high radiation levels around the loaded casks, where workers must function during the measurement of contamination levels and while decontaminating the cask. In order to optimize the total dose received due to compliance with cask contamination levels, it is necessary to take into account all the doses that vary as a result of the regulatory limit. Limits for non-fixed surface contamination on spent fuel casks should be established by using a model that considers and optimizes the appropriate exposure scenarios both in the workplace and in the public environment. A risk-informed approach is needed to ensure optimal use of personnel and material resources for SNF-based packaging operations. This paper is a summary of a study sponsored by the US Nuclear Regulatory Commission and performed by Oak Ridge National Laboratory that examined the dose implications for removable surface contamination limits on spent fuel

  2. Morphology and Differentiation of MG63 Osteoblast Cells on Saliva Contaminated Implant Surfaces

    Directory of Open Access Journals (Sweden)

    Neda Shams

    2015-11-01

    Full Text Available Objectives: Osteoblasts are the most important cells in the osseointegration process. Despite years of study on dental Implants, limited studies have discussed the effect of saliva on the adhesion process of osteoblasts to implant surfaces. The aim of this in vitro study was to evaluate the effect of saliva on morphology and differentiation of osteoblasts attached to implant surfaces.Materials and Methods: Twelve Axiom dental implants were divided into two groups. Implants of the case group were placed in containers, containing saliva, for 40 minutes. Then, all the implants were separately stored in a medium containing MG63 human osteoblasts for a week. Cell morphology and differentiation were assessed using a scanning electron microscope and their alkaline phosphatase (ALP activity was determined. The t-test was used to compare the two groups.Results: Scanning electron microscopic observation of osteoblasts revealed round or square cells with fewer and shorter cellular processes in saliva contaminated samples, whereas elongated, fusiform and well-defined cell processes were seen in the control group. ALP level was significantly lower in case compared to control group (P<0.05.Conclusion: Saliva contamination alters osteoblast morphology and differentiation and may subsequently interfere with successful osseointegration. Thus, saliva contamination of bone and implant must be prevented or minimized.

  3. Multicenter evaluation of a new closed system drug-transfer device in reducing surface contamination by antineoplastic hazardous drugs.

    Science.gov (United States)

    Bartel, Sylvia B; Tyler, Timothy G; Power, Luci A

    2018-02-15

    Results of a study to evaluate the effectiveness of a recently introduced closed system drug-transfer device (CSTD) in reducing surface contamination during compounding and simulated administration of antineoplastic hazardous drugs (AHDs) are reported. Wipe samples were collected from 6 predetermined surfaces in compounding and infusion areas of 13 U.S. cancer centers to establish preexisting levels of surface contamination by 2 marker AHDs (cyclophosphamide and fluorouracil). Stainless steel templates were placed over the 6 previously sampled surfaces, and the marker drugs were compounded and infused per a specific protocol using all components of the CSTD. Wipe samples were collected from the templates after completion of tasks and analyzed for both marker AHDs. Aggregated results of wipe sampling to detect preexisting contamination at the 13 study sites showed that overall, 66.7% of samples (104 of 156) had detectable levels of at least 1 marker AHD; subsequent testing after CSTD use per protocol found a sample contamination rate of 5.8% (9 of 156 samples). In the administration areas alone, the rate of preexisting contamination was 78% (61 of 78 samples); with use of the CSTD protocol, the contamination rate was 2.6%. Twenty-six participants rated the CSTD for ease of use, with 100% indicating that they were satisfied or extremely satisfied. A study involving a rigorous protocol and 13 cancer centers across the United States demonstrated that the CSTD reduced surface contamination by cyclophosphamide and fluorouracil during compounding and simulated administration. Participants reported that the CSTD was easy to use. Copyright © 2018 by the American Society of Health-System Pharmacists, Inc. All rights reserved.

  4. Eradication of high viable loads of Listeria monocytogenes contaminating food-contact surfaces

    Directory of Open Access Journals (Sweden)

    Silvia ede Candia

    2015-07-01

    Full Text Available This study demonstrates the efficacy of cold gaseous ozone treatments at low concentrations in the eradication of high Listeria monocytogenes viable cell loads from glass, polypropylene, stainless steel and expanded polystyrene food-contact surfaces. Using a step by step approach, involving the selection of the most resistant strain-surface combinations, 11 Listeria spp. strains resulted inactivated by a continuous ozone flow at 1.07 mg m-3 after 24 or 48 h of cold incubation, depending on both strain and surface evaluated. Increasing the inoculum level to 9 log CFU coupon-1, the best inactivation rate was obtained after 48h of treatment at 3.21 mg m-3 ozone concentration when cells were deposited onto stainless steel and expanded polystyrene coupons, resulted the most resistant food-contact surfaces in the previous assays.The addition of naturally microbiologically contaminated meat extract to a high load of L. monocytogenes LMG 23775 cells, the most resistant strain out of the 11 assayed Listeria spp. strains, led to its complete inactivation after four days of treatment.To the best of our knowledge, this is the first report describing the survival of L. monocytogenes and the effect of ozone treatment under cold storage conditions on expanded polystyrene, a commonly-used material in food packaging. These results could be useful for reducing pathogen cross-contamination phenomena during cold food storage.

  5. Quantifying potential sources of surface water contamination with Campylobacter jejuni and Campylobacter coli.

    Science.gov (United States)

    Mughini-Gras, Lapo; Penny, Christian; Ragimbeau, Catherine; Schets, Franciska M; Blaak, Hetty; Duim, Birgitta; Wagenaar, Jaap A; de Boer, Albert; Cauchie, Henry-Michel; Mossong, Joel; van Pelt, Wilfrid

    2016-09-15

    Campylobacter is the most common causative agent of human bacterial gastroenteritis and is frequently found in surface water, where it indicates recent contamination with animal faeces, sewage effluent, and agricultural run-off. The contribution of different animal reservoirs to surface water contamination with Campylobacter is largely unknown. In the Netherlands, the massive poultry culling to control the 2003 avian influenza epidemic coincided with a 44-50% reduction in human campylobacteriosis cases in the culling areas, suggesting substantial environment-mediated spread of poultry-borne Campylobacter. We inferred the origin of surface water Campylobacter jejuni and Campylobacter coli strains in Luxembourg and the Netherlands, as defined by multilocus sequence typing, by comparison to strains from poultry, pigs, ruminants, and wild birds, using the asymmetric island model for source attribution. Most Luxembourgish water strains were attributed to wild birds (61.0%), followed by poultry (18.8%), ruminants (15.9%), and pigs (4.3%); whereas the Dutch water strains were mainly attributed to poultry (51.7%), wild birds (37.3%), ruminants (9.8%), and pigs (1.2%). Attributions varied over seasons and surface water types, and geographical variation in the relative contribution of poultry correlated with the magnitude of poultry production at either the national or provincial level, suggesting that environmental dissemination of Campylobacter from poultry farms and slaughterhouses can be substantial in poultry-rich regions. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Radioactive contamination of some rubber or plastic surfaces by fission products. Decontamination tests

    International Nuclear Information System (INIS)

    Mestre, E.; Sautiez, N.

    1957-10-01

    With the objective of notably addressing the contamination and decontamination of gloves and floor covering, this report first presents some characteristics of contaminating radioactive materials (nature, physical and chemical condition), of contaminated surfaces (surface condition, surface nature), and of decontamination processes (physical, chemical or mechanical action). It describes the operational modality implemented to test decontamination processes on various glove or flooring materials: sample preparation, counting, decontamination, reproducibility of decontamination tests, results in terms of activity reduction. It more precisely describes the tested samples: short gloves, gloves from glove boxes, floor and wall coverings. Results are presented and discussed in terms of sample susceptibility to contamination, and of decontamination, but also for re-contamination tests after a Nab-based decontamination (susceptibility to contamination, decontamination gain)

  7. The accuracy of surface-contamination measurements; survey of UK hospitals, 1986

    International Nuclear Information System (INIS)

    Woods, M.J.

    1987-01-01

    In response to a number of concerns expressed at both national and international levels, the National Physical Laboratory (NPL) conducted a survey of UK hospitals and associated Regional Radiation Protection Services. Sources of surface contamination were distributed and participants were requested to measure these and interpret the relevant responses in terms of emission and activity per unit area. The analysis of the returns demonstrates that the vast majority of results was significantly in error and that the quality of radiation protection may be impaired. (author)

  8. Environmental contamination from a ground-level release of fission products

    International Nuclear Information System (INIS)

    Stupka, R.C.; Kephart, G.S.; Rittmann, P.D.

    1986-08-01

    On January 11, 1985, a ground-level release of fission products, primarily 90 Sr, occurred at the Hanford Site in southeastern Washington State. The release was detected during routine surveys and the majority of the contamination was confined to the immediate area where the release occurred. Response to the incident was complicated by a strong inversion that resulted in a buildup of 222 Rn daughter products on environmental air samples and outdoor surfaces. The cause of the release appears to have been the operation of a transfer jet that inadvertently pressurized an unblanked line leading to the 241-C-151 Diversion Box. A buildup of pressure inside the diversion box forced contaminated air through gaps in the diversion box cover blocks resulting in an unmonitored, short duration release to the environment. The source term was estimated using data obtained from environmental air samplers. The ground deposition speed was calculated using the integrated exposure (air samples) and surface contamination levels obtained from recently fallen snow. The total release was estimated to be 1.4 Ci 90 Sr and 0.02 Ci 137 Cs. Based on this source term, the maximum 50-yr dose commitment to onsite pesonnel was 50 mrem whole body and 600 mrem bone. No detectable internal deposition occurred during the incident and corrective action which followed; this was probably due to several factors: (1) prompt detection of the release; (2) localized contamination control; (3) excellent personnel protection practices; and (4) the protection offered by building ventilation systems. The theoretical maximum offsite individual would receive a potential 1-yr dose commitment of 0.01 mrem whole body and 0.2 mrem bone from this incident. The potential 50-yr dose commitment would be 0.13 mrem whole body and 2.0 mrem bone. In actuality, neither onsite or offsite individuals would be expected to receive even these small dose commitments

  9. Stochastic Radiative Transfer Model for Contaminated Rough Surfaces: A Framework for Detection System Design

    Science.gov (United States)

    2013-11-01

    Contaminated surfaces Detection Rough surface BRDF Reflectance Fill factor CFAR Data fusion (Continued on next page.) 16...surfaces, detection, rough surface, BRDF, reflectance, fill factor, distributed binary integration, CFAR , data fusion, distributed sensor system, double...detection, tem)detect(sys)( 1 PP systemmiss  , for a given constraint of constant false alarm ( CFAR ) system-false-alarm probability, )( systemfalseP

  10. Lead contamination and transfer in urban environmental compartments analyzed by lead levels and isotopic compositions

    International Nuclear Information System (INIS)

    Hu, Xin; Sun, Yuanyuan; Ding, Zhuhong; Zhang, Yun; Wu, Jichun; Lian, Hongzhen; Wang, Tijian

    2014-01-01

    Lead levels and isotopic compositions in atmospheric particles (TSP and PM 2.5 ), street dust and surface soil collected from Nanjing, a mega city in China, were analyzed to investigate the contamination and the transfer of lead in urban environmental compartments. The lead contents in TSP and PM 2.5 are significantly higher than them in the surface soil and street dust (p  206 Pb/ 207 Pb vs. 208 Pb/ 206 Pb and 206 Pb/ 207 Pb vs. 1/Pb imply that the street dust and atmospheric particles (TSP and PM 2.5 ) have very similar lead sources. Coal emissions and smelting activities may be the important lead sources for street dust and atmospheric particles (TSP and PM 2.5 ), while the deposition of airborne lead is an important lead source for urban surface soil. - Highlights: • Lead levels and isotope ratios in atmospheric particles, street dust and surface soil. • Significant enrichment of lead in atmospheric particles was observed. • Street dust and atmospheric particles have similar lead sources. • Endmembers of soil lead differ from street dust and atmospheric particles. • Airborne lead poses the main risks to unban environmental quality. - Transfer of airborne particle bound lead into street dust and surface soil in unban environmental based on lead levels and isotopic compositions

  11. Is metal contamination responsible for increasing aneuploidy levels in the Manila clam Ruditapes philippinarum?

    KAUST Repository

    Piló, D.

    2016-11-03

    The present study assessed the metal genotoxicity potential at chromosome-level in the bivalve Ruditapes philippinarum collected along different areas of the Tagus estuary. Higher levels of aneuploidy on gill cells were detected at the most sediment contaminated area both in May (31.7%) and October (36.0%) when compared to a less contaminated area over the same periods (20.3% and 29.0% respectively). Interestingly, metal bioaccumulation in gills was higher in the specimens collected at the least contaminated area with the exception of Pb. Indeed, the multivariate analysis revealed a stronger relation between aneuploidy and sediment contamination than between aneuploidy and the bioaccumulation of the metals. The temporal and spatial inconsistency found for the bioaccumulation of metals in R. philippinarum and the positive correlation between sediment contamination and aneuploidy at the most contaminated area suggest that these chromosome-level effects might be due to chronic metal contamination occurring in the Tagus estuary, rather than a direct result of the temporal variation of bioavailable contaminants. The vertical transmission phenomenon of bivalve aneuploidy levels may then be perpetuating those levels on clams from the most contaminated area. The present results shed light about the effect of metal toxicity at the chromosome-level in species inhabiting chronic contaminated areas and highlight the use of aneuploidy as an effective tool to identify persistent contamination in worldwide transitional waters.

  12. Fate factors and emission flux estimates for emerging contaminants in surface waters

    Directory of Open Access Journals (Sweden)

    Hoa T. Trinh

    2016-01-01

    Full Text Available Pharmaceuticals, personal care products, hormones, and wastewater products are emerging environmental concerns for manifold reasons, including the potential of some compounds found in these products for endocrine disruption at a very low chronic exposure level. The environmental occurrences and sources of these contaminants in the water, soil, sediment and biota in European nations and the United States are well documented. This work reports a screening-level emission and fate assessment of thirty compounds, listed in the National Reconnaissance of the United States Geological Survey (USGS, 1999–2000 as the most frequently detected organic wastewater contaminants in U.S. streams and rivers. Estimations of the surface water fate factors were based on Level II and Level III multimedia fugacity models for a 1000 km2 model environment, the size of a typical county in the eastern United States. The compounds are categorized into three groups based upon the sensitivity of their predicted surface water fate factors to uncertainties in their physicochemical property values and the landscape parameters. The environmental fate factors, mass distributions, and loss pathways of all of the compounds are strongly affected by their assumed modes of entry into the environment. It is observed that for thirteen of the thirty organic wastewater contaminants most commonly detected in surface waters, conventional treatment strategies may be ineffective for their removal from wastewater effluents. The surface water fate factors predicted by the fugacity models were used in conjunction with the surface water concentrations measured in the USGS reconnaissance to obtain emission flux estimates for the compounds into U.S. streams and rivers. These include estimated fluxes of 6.8 × 10−5 to 0.30 kg/h km2 for the biomarker coprostanol; 1.7 × 10−5 to 6.5 × 10−5 kg/h km2 for the insect repellent N,N-diethyltoluamide; and 4.3 × 10−6 to 3.1 × 10−5 kg/h km2 for

  13. Vegetated Treatment Systems for Removing Contaminants Associated with Surface Water Toxicity in Agriculture and Urban Runoff.

    Science.gov (United States)

    Anderson, Brian S; Phillips, Bryn M; Voorhees, Jennifer P; Cahn, Michael

    2017-05-15

    Urban stormwater and agriculture irrigation runoff contain a complex mixture of contaminants that are often toxic to adjacent receiving waters. Runoff may be treated with simple systems designed to promote sorption of contaminants to vegetation and soils and promote infiltration. Two example systems are described: a bioswale treatment system for urban stormwater treatment, and a vegetated drainage ditch for treating agriculture irrigation runoff. Both have similar attributes that reduce contaminant loading in runoff: vegetation that results in sorption of the contaminants to the soil and plant surfaces, and water infiltration. These systems may also include the integration of granulated activated carbon as a polishing step to remove residual contaminants. Implementation of these systems in agriculture and urban watersheds requires system monitoring to verify treatment efficacy. This includes chemical monitoring for specific contaminants responsible for toxicity. The current paper emphasizes monitoring of current use pesticides since these are responsible for surface water toxicity to aquatic invertebrates.

  14. Bond strength of resin-resin interfaces contaminated with saliva and submitted to different surface treatments.

    Science.gov (United States)

    Furuse, Adilson Yoshio; da Cunha, Leonardo Fernandes; Benetti, Ana Raquel; Mondelli, José

    2007-12-01

    The purpose of this study was to investigate the effect of different surface treatments on shear bond strength of saliva-contaminated resin-resin interfaces. Flat resin surfaces were fabricated. In the control group, no contamination or surface treatment was performed. The resin surfaces of the experimental groups were contaminated with saliva and air-dried, and then submitted to: (G1) rinsing with water and drying; (G2) application of an adhesive system; (G3) rinsing and drying, abrasion with finishing disks, etching and application of adhesive system; (G4) rinsing and drying, etching, application of silane and adhesive system. Resin cylinders were placed over the treated surfaces. The specimens were stored in water or ethanol. Shear bond strength tests were performed and the mode of failure was evaluated. Data were submitted to two-way ANOVA and Dunnett T3 test. Contamination of resin-resin interfaces with saliva significantly reduced shear strength, especially after prolonged storage (presin increments.

  15. Measurements of the spatial distribution of tritium in air above a chronically contaminated surface

    International Nuclear Information System (INIS)

    Workman, W.J.G.; Davis, P.A.; Wood, M.J.; Barry, P.J.

    1993-01-01

    Tritium in air (HTO) concentrations were measured over a 13 month period above a surface that is chronically contaminated by tritium-bearing groundwater from a waste management area. The measurements were made using passive diffusion samplers, which were sited at six locations (about 100 m apart) at 0.15, 0.9, and 1.8 m above ground level. The diffusion samplers were compact, sampled at a known rate, and required no external power source. They are ideal for remote locations and require a minimum of effort to collect and analyze the data. HTO-in-air concentration peaked in the summer at 500-1500 Bq.m -3 and decreased in the winter to 1-120 Bq.m -3 . In general, concentration decreased with height above ground level, implying that HTO is being lost from the surface to the atmosphere. The flux of tritium to the atmosphere must, therefore, be taken into account to estimate the tritium mass balance for a contaminated area. (Author) 3 figs., 5 tabs., 10 refs

  16. Bioremediation of hydrocarbon contaminated surface water, groundwater, and soils

    International Nuclear Information System (INIS)

    Piotrowski, M.R.

    1991-01-01

    Bioremediation is currently receiving considerable attention as a remediation option for sites contaminated with hazardous organic compounds. There is an enormous amount of interest in bioremediation, and numerous journals now publish research articles concerning some aspect of the remediation approach. A review of the literature indicates that two basic forms of bioremediation are currently being practiced: the microbiological approach and the microbial ecology approach. Each form has its advocates and detractors, and the microbiological approach is generally advocated by most of the firms that practice bioremediation. In this paper, the merits and disadvantages of these forms are reviewed and a conceptual approach is presented for assessing which form may be most useful for a particular contaminant situation. I conclude that the microbial ecology form of bioremediation may be the most useful for the majority of contaminant situations, and I will present two case histories in support of this hypothesis

  17. Laboratory Studies on Surface Sampling of Bacillus anthracis Contamination: Summary, Gaps, and Recommendations

    Energy Technology Data Exchange (ETDEWEB)

    Piepel, Gregory F.; Amidan, Brett G.; Hu, Rebecca

    2011-11-28

    This report summarizes previous laboratory studies to characterize the performance of methods for collecting, storing/transporting, processing, and analyzing samples from surfaces contaminated by Bacillus anthracis or related surrogates. The focus is on plate culture and count estimates of surface contamination for swab, wipe, and vacuum samples of porous and nonporous surfaces. Summaries of the previous studies and their results were assessed to identify gaps in information needed as inputs to calculate key parameters critical to risk management in biothreat incidents. One key parameter is the number of samples needed to make characterization or clearance decisions with specified statistical confidence. Other key parameters include the ability to calculate, following contamination incidents, the (1) estimates of Bacillus anthracis contamination, as well as the bias and uncertainties in the estimates, and (2) confidence in characterization and clearance decisions for contaminated or decontaminated buildings. Gaps in knowledge and understanding identified during the summary of the studies are discussed and recommendations are given for future studies.

  18. Exploring Surface Analysis Techniques for the Detection of Molecular Contaminants on Spacecraft

    Science.gov (United States)

    Rutherford, Gugu N.; Seasly, Elaine; Thornblom, Mark; Baughman, James

    2016-01-01

    Molecular contamination is a known area of concern for spacecraft. To mitigate this risk, projects involving space flight hardware set requirements in a contamination control plan that establishes an allocation budget for the exposure of non-volatile residues (NVR) onto critical surfaces. The purpose of this work will focus on non-contact surface analysis and in situ monitoring to mitigate molecular contamination on space flight hardware. By using Scanning Electron Microscopy and Energy Dispersive Spectroscopy (SEM-EDS) with Raman Spectroscopy, an unlikely contaminant was identified on space flight hardware. Using traditional and surface analysis methods provided the broader view of the contamination sources allowing for best fit solutions to prevent any future exposure.

  19. 40 CFR 142.61 - Variances from the maximum contaminant level for fluoride.

    Science.gov (United States)

    2010-07-01

    ... level for fluoride. 142.61 Section 142.61 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... from the maximum contaminant level for fluoride. (a) The Administrator, pursuant to section 1415(a)(1... means generally available for achieving compliance with the Maximum Contaminant Level for fluoride. (1...

  20. Soil contamination of plant surfaces from grazing and rainfall interactions

    International Nuclear Information System (INIS)

    Hinton, T.G.; Stoll, J.M.; Tobler, L.

    1995-01-01

    Contaminants often attach to soil particles, and their subsequent environmental transport is largely determined by processes that govern soil movement. We examined the influence of grazing intensity on soil contamination of pastures. Four different grazing densities of sheep were tested against an ungrazed control plot. Scandium concentrations were determined by neutron activation analysis and was used as a tracer of soil adhesion on vegetation. Soil loadings ( g soil kg -1 dry plant) increased 60% when grazing intensity was increased by a factor of four (p 0.003). Rain and wind removed soil from vegetation in the ungrazed control plots, but when grazing sheep were present, an increase in rain from 0.3 to 9.7 mm caused a 130% increase in soil contamination. Multiple regression was used to develop an equation that predicts soil loadings as a function of grazing density, rainfall and wind speed (p = 0.0001, r 2 = 0.78). The model predicts that if grazing management were to be used as a tool to reduce contaminant intake from inadvertent consumption of resuspended soil by grazing animals, grazing densities would have to be reduced 2.5 times to reduce soil loadings by 50%. (author)

  1. Metal Hydride assited contamination on Ru/Si surfaces

    NARCIS (Netherlands)

    Pachecka, Malgorzata; Lee, Christopher James; Sturm, Jacobus Marinus; Bijkerk, Frederik

    2013-01-01

    In extreme ultraviolet lithography (EUVL) residual tin, in the form of particles, ions, and atoms, can be deposited on nearby EUV optics. During the EUV pulse, a reactive hydrogen plasma is formed, which may be able to react with metal contaminants, creating volatile and unstable metal hydrides that

  2. Microbial contamination of contact surfaces at eating houses in ...

    African Journals Online (AJOL)

    A study of five highly patronized eating houses in a university community was conducted to assess the microbiological quality of some food contact and ... The predominant bacterial contaminants were isolated, characterized and identified as E. coli, S. aureus, Pseudomonas aeruginosa, Proteus spp., Salmonella spp. and ...

  3. Microbial Contamination Level Profiles Attributed to Contamination of Beef Carcasses, Personnel, and Equipment: Case of Small and Medium Enterprise Slaughterhouses.

    Science.gov (United States)

    Wambui, Joseph; Lamuka, Peter; Karuri, Edward; Matofari, Joseph; Njage, Patrick Murigu Kamau

    2018-04-01

    The microbial contamination level profiles (MCLPs) attributed to contamination of beef carcasses, personnel, and equipment in five Kenyan small and medium enterprise slaughterhouses were determined. Aerobic plate counts, Enterobacteriaceae, Staphylococcus, and Salmonella were used to determine contamination at four different slaughter stages, namely, dehiding, evisceration, splitting, and dispatch. Microbiological criteria of the four microorganisms were used to score contamination levels (CLs) as poor (0), poor to average (1), average (2), or good (3). MCLPs were further assigned to carcasses, personnel, and equipment at each stage by summing up the CL scores. The CL score attributed to aerobic plate count contamination was 2 or 3 for carcasses but 0 for personnel and equipment in almost all slaughterhouses. A score of 0 on carcasses was mostly attributed to Enterobacteriaceae at evisceration and to Salmonella at dehiding and evisceration. In addition, a score of 0 was mostly attributed to Staphylococcus contamination of personnel at dehiding. A score of 3 was attributed mostly to Enterobacteriaceae on hands at splitting, whereas a score of 2 was mostly attributed to the clothes at dehiding and evisceration. A CL score of 3 was mostly attributed to Enterobacteriaceae and Salmonella contamination of equipment at dehiding and splitting, respectively. Although CLs attributed to contamination of carcasses, personnel, and equipment ranged from 0 to 3, the maximum MCLP score of 9 was only attained in carcasses from two slaughterhouses at dehiding and from one slaughterhouse at dispatch. There is, therefore, a lot of room for small and medium enterprise slaughterhouses to improve their food safety objectives by improving food safety management systems at the points characterized by low CL scores.

  4. National Enforcement Initiative: Preventing Animal Waste from Contaminating Surface and Ground Water

    Science.gov (United States)

    This page describes EPA's goal in preventing animal waste from contaminating surface and ground Water. It is an EPA National Enforcement Initiative. Both enforcement cases, and a map of enforcement actions are provided.

  5. Effect of surface contamination on osseointegration of dental implants surrounded by circumferential bone defects.

    LENUS (Irish Health Repository)

    Mohamed, Seif

    2010-05-01

    This study was designed to evaluate the effect of surface contamination on osseointegration of dental implants surrounded by a circumferential bone defect and to compare osseointegration around Osseotite with that around Nanotite implants.

  6. Allowable Residual Contamination Levels in soil for decommissioning the Shippingport Atomic Power Station site

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Napier, B.A.; Soldat, J.K.

    1983-09-01

    As part of decommissioning the Shippingport Atomic Power Station, a fundamental concern is the determination of Allowable Residual Contamination Levels (ARCL) for radionuclides in the soil at the site. The ARCL method described in this report is based on a scenario/exposure-pathway analysis and compliance with an annual dose limit for unrestricted use of the land after decommissioning. In addition to naturally occurring radionuclides and fallout from weapons testing, soil contamination could potentially come from five other sources. These include operation of the Shippingport Station as a pressurized water reactor, operations of the Shippingport Station as a light-water breeder, operation of the nearby Beaver Valley reactors, releases during decommissioning, and operation of other nearby industries, including the Bruce-Mansfield coal-fired power plants. ARCL values are presented for 29 individual radionculides and a worksheet is provided so that ARCL values can be determined for any mixture of the individual radionuclides for any annual dose limit selected. In addition, a worksheet is provided for calculating present time soil concentration value that will decay to the ARCL values after any selected period of time, such as would occur during a period of restricted access. The ARCL results are presented for both unconfined (surface) and confined (subsurface) soil contamination. The ARCL method and results described in this report provide a flexible means of determining unrestricted-use site release conditions after decommissioning the Shippingport Atomic Power Station

  7. A prospective survey of air and surface fungal contamination in a medical mycology laboratory at a tertiary care university hospital.

    Science.gov (United States)

    Sautour, Marc; Dalle, Frédéric; Olivieri, Claire; L'ollivier, Coralie; Enderlin, Emilie; Salome, Elsa; Chovelon, Isabelle; Vagner, Odile; Sixt, Nathalie; Fricker-Pap, Véronique; Aho, Serge; Fontaneau, Olivier; Cachia, Claire; Bonnin, Alain

    2009-04-01

    Invasive filamentous fungi infections resulting from inhalation of mold conidia pose a major threat in immunocompromised patients. The diagnosis is based on direct smears, cultural symptoms, and culturing fungi. Airborne conidia present in the laboratory environment may cause contamination of cultures, resulting in false-positive diagnosis. Baseline values of fungal contamination in a clinical mycology laboratory have not been determined to date. A 1-year prospective survey of air and surface contamination was conducted in a clinical mycology laboratory during a period when large construction projects were being conducted in the hospital. Air was sampled with a portable air system impactor, and surfaces were sampled with contact Sabouraud agar plates. The collected data allowed the elaboration of Shewhart graphic charts. Mean fungal loads ranged from 2.27 to 4.36 colony forming units (cfu)/m(3) in air and from 0.61 to 1.69 cfu/plate on surfaces. Strict control procedures may limit the level of fungal contamination in a clinical mycology laboratory even in the context of large construction projects at the hospital site. Our data and the resulting Shewhart graphic charts provide baseline values to use when monitoring for inappropriate variations of the fungal contamination in a mycology laboratory as part of a quality assurance program. This is critical to the appropriate management of the fungal risk in hematology, cancer and transplantation patients.

  8. Level of Faecal Coliform Contamination of Drinking Water Sources ...

    African Journals Online (AJOL)

    2018-03-01

    Mar 1, 2018 ... CONCLUSION: In this study, the prevalence of positive faecal coliform at water source was high. Educational status, sanitary. Risk of contamination at the water source, water shortage experience had significant associations with the presence of faecal coliform in drinking water sources. KEYWORDS: Water ...

  9. Chemical analysis of outgassing contaminants on spacecraft surfaces

    Science.gov (United States)

    Mcnutt, R. C.

    1973-01-01

    Methods for analyzing and characterizing outgassing contaminants from such materials as RTV 501 potting compound and S 13 G paint are presented. Fractional distillation of a gross distillate from RTV 501 rubber was carried out and the distilled fractions examined as to their ultraviolet and infrared spectra by gas liquid chromatography. A sensitive technique for structural analysis and molecular identification was found to consist of a gas chromatography-mass spectroscopy system, which was determined to be economically unfeasible at present.

  10. 40 CFR 142.63 - Variances and exemptions from the maximum contaminant level for total coliforms.

    Science.gov (United States)

    2010-07-01

    ... maximum contaminant level for total coliforms. 142.63 Section 142.63 Protection of Environment... Available § 142.63 Variances and exemptions from the maximum contaminant level for total coliforms. (a) No... due to a persistent growth of total coliforms in the distribution system rather than fecal or...

  11. Combined Contamination and Space Environmental Effects on Solar Cells and Thermal Control Surfaces

    Science.gov (United States)

    Dever, Joyce A.; Bruckner, Eric J.; Scheiman, David A.; Stidham, Curtis R.

    1994-01-01

    For spacecraft in low Earth orbit (LEO), contamination can occur from thruster fuel, sputter contamination products and from products of silicone degradation. This paper describes laboratory testing in which solar cell materials and thermal control surfaces were exposed to simulated spacecraft environmental effects including contamination, atomic oxygen, ultraviolet radiation and thermal cycling. The objective of these experiments was to determine how the interaction of the natural LEO environmental effects with contaminated spacecraft surfaces impacts the performance of these materials. Optical properties of samples were measured and solar cell performance data was obtained. In general, exposure to contamination by thruster fuel resulted in degradation of solar absorptance for fused silica and various thermal control surfaces and degradation of solar cell performance. Fused silica samples which were subsequently exposed to an atomic oxygen/vacuum ultraviolet radiation environment showed reversal of this degradation. These results imply that solar cells and thermal control surfaces which are susceptible to thruster fuel contamination and which also receive atomic oxygen exposure may not undergo significant performance degradation. Materials which were exposed to only vacuum ultraviolet radiation subsequent to contamination showed slight additional degradation in solar absorptance.

  12. Methods for the calculation of derived working limits for surface contamination by low-toxicity radionuclides

    International Nuclear Information System (INIS)

    Gibson, J.A.B.; Wrixon, A.D.

    1979-01-01

    Surface contamination is often measured as an indication of the general spread of radioactive contamination in a particular place. Derived working limits, (DWLs) for surface contamination provide figures against which to assess the significance of measurements. Derived working limits for surface contamination were first established for use in the nuclear energy industry. They were designed to cope with a wide range of unspecified radionuclides and were therefore based on the assumption that the contamination was due to the presence of the most hazardous radionuclides, e.g. 90 Sr, 210 Pb, 226 Ra and 239 Pu. While this assumption may still be appropriate when the radionuclide mixture is unknown, there are now many specialized uses of particular low-toxicity radionuclides in universities, hospitals and general industry. If it is known that only a particular radionuclide is present, the general DWL can be replaced by a more specific value. The methods for calculating DWLs for some of the more commonly employed low-toxicity radionuclides are described. The exposure pathways considered are (a) external radiation of the skin and inhalation of airborne material from contaminated surfaces in active areas; (b) external irradiation of the skin and ingestion from contaminated skin. Some consideration is given to the effect of the revised dose equivalent limits in the most recent recommendations of ICRP. (author)

  13. EM Task 12 - Laser cleaning of Contaminated Painted Surfaces

    International Nuclear Information System (INIS)

    Ames A. Grisanti; Charlene R. Crocker; Robert J. Jensen

    1998-01-01

    Several techniques are available or under development for surface decontamination in nuclear facilities. Each technique has its merits; however, none of them is universally the best choice for all surface decontamination applications. Because of the multitude of factors which influence the environmental and economic aspects of selecting a surface decontamination technique, it is difficult to select the best method in a given situation; an objective basis for comparing techniques is needed. The objective of this project is to develop a software tool for use by personnel selecting a surface decontamination technique. The software will incorporate performance data for available surface decontamination techniques. The beta release of the Surface Decontamination Assistant Software has been completed and has undergone testing at the Energy and Environmental Research Center (EERC). Minor modifications to the software will be completed before the end of November 1998, and a final release of the software will be issued

  14. EM Task 12 - Laser cleaning of contaminated painted surfaces

    International Nuclear Information System (INIS)

    Grisanti, Ames A.; Crocker, Charlene R.; Jensen, Robert R.

    1999-01-01

    Several techniques are available or under development for surface decontamination in nuclear facilities. Each technique has its merits; however, none of them is universally the best choice for all surface decontamination applications. Because of the multitude of factors which influence the environmental and economic aspects of selecting a surface decontamination technique, it is difficult to select the best method in a given situation; an objective basis for comparing techniques is needed. The objective of this project was to develop a software tool for use by personnel selecting a surface decontamination technique. The software incorporates performance data for available surface decontamination techniques. The beta release version of the Surface Decontamination Assistant Software has been completed and has undergone testing at the Energy and Environmental Research Center. Minor modifications to the software were completed, and a final release version of the software is ready to be issued

  15. Contamination of rural surface and ground water by endosulfan in farming areas of the Western Cape, South Africa

    Directory of Open Access Journals (Sweden)

    London Leslie

    2003-03-01

    Full Text Available Abstract Background In South Africa there is little data on environmental pollution of rural water sources by agrochemicals. Methods This study investigated pesticide contamination of ground and surface water in three intensive agricultural areas in the Western Cape: the Hex River Valley, Grabouw and Piketberg. Monitoring for endosulfan and chlorpyrifos at low levels was conducted as well as screening for other pesticides. Results The quantification limit for endosulfan was 0.1 μg/L. Endosulfan was found to be widespread in ground water, surface water and drinking water. The contamination was mostly at low levels, but regularly exceeded the European Drinking Water Standard of 0.1 μg/L. The two most contaminated sites were a sub-surface drain in the Hex River Valley and a dam in Grabouw, with 0.83 ± 1.0 μg/L (n = 21 and 3.16 ± 3.5 μg/L (n = 13 average endosulfan levels respectively. Other pesticides including chlorpyrifos, azinphos-methyl, fenarimol, iprodione, deltamethrin, penconazole and prothiofos were detected. Endosulfan was most frequently detected in Grabouw (69% followed by Hex River (46% and Piketberg (39%. Detections were more frequent in surface water (47% than in groundwater (32% and coincided with irrigation, and to a lesser extent, to spraying and trigger rains. Total dietary endosulfan intake calculated from levels found in drinking water did not exceed the Joint WHO/FAO Meeting on Pesticide Residues (JMPR criteria. Conclusion The study has shown the need for monitoring of pesticide contamination in surface and groundwater, and the development of drinking water quality standards for specific pesticides in South Africa.

  16. Assessment of the contaminants level in recycled aggregates and alternative new technologies for contaminants recognition and removal

    NARCIS (Netherlands)

    Lotfi, S.; Di Maio, F.; Xia, H.; Serranti, S.; Palmieri, R.; Bonifazi, G.

    2015-01-01

    One of the main challenging problems associated with the use of Recycled Aggregates (RA) is the level of mixed contaminants. For utilizing RA in high-grade applications, it is essential to monitor and minimise the content of the pollutants. To this extent the C2CA concrete recycling process

  17. Study of surface potential contamination in radioisotope and radiopharmaceutical production facilities and alternative solutions

    International Nuclear Information System (INIS)

    Suhaedi Muhammad; Rimin Sumantri; Farida Tusafariah; Djarwanti Rahayu Pipin Soedjarwo

    2013-01-01

    Radioisotope and radiopharmaceutical production facilities that exist in their operations around the world in the form of radiological impacts of radiation exposure, contamination of surface and air contamination. Given the number of existing open source in radioisotope and radiopharmaceutical production facility, then the possibility of surface contamination in the work area is quite high. For that to protect the safety and health of both workers, the public and the environment, then the licensee must conduct an inventory of some of the potential that could result in contamination of surfaces in radioisotope and radiopharmaceutical production facilities. Several potential to cause surface contamination in radioisotope and radiopharmaceutical production facilities consist of loss of resources, the VAC system disorders, impaired production facilities, limited resources and lack of work discipline and radioactive waste handling activities. From the study of some potential, there are several alternative solutions that can be implemented by the licensee to address the contamination of the surface so as not to cause adverse radiological impacts for both radiation workers, the public or the environment. (author)

  18. Study on Microbial Deposition and Contamination onto Six Surfaces Commonly Used in Chemical and Microbiological Laboratories

    Directory of Open Access Journals (Sweden)

    Elena Tamburini

    2015-07-01

    Full Text Available The worktops in both chemical and microbiological laboratories are the surfaces most vulnerable to damage and exposure to contamination by indoor pollutants. The rate at which particles are deposited on indoor surfaces is an important parameter to determine human exposure to airborne biological particles. In contrast to what has been established for inorganic pollutants, no limit has been set by law for microbial contamination in indoor air. To our knowledge, a comparative study on the effect of surfaces on the deposition of microbes has not been carried out. An evaluation of the microbial contamination of worktop materials could be of crucial importance, both for safety reasons and for the reliability of tests and experiments that need to be carried out in non-contaminated environments. The aim of this study was to evaluate the overall microbial contamination (fungi, mesophilic and psychrophilic bacteria, staphylococci on six widely used worktop materials in laboratories (glass, stainless steel, fine porcelain stoneware, post-forming laminate, high-performing laminate and enamel steel and to correlate it with the characteristics of the surfaces. After cleaning, the kinetics of microbial re-contamination were also evaluated for all surfaces.

  19. Microbial contaminants on some fish contact surfaces in Sokoto ...

    African Journals Online (AJOL)

    Sokoto central market and two privately owned fish cold room and distribution outlets were visited between August and September, 2005 to collect surface swabs. The sampled surfaces included a concrete table and two basins from the market, weighing pans, floor and walls of cold rooms from the two distribution outlets.

  20. Contamination of Teflon surfaces by PCBs in the atmosphere

    Science.gov (United States)

    Murphy, Thomas J.; Sweet, Clyde W.

    Collection of a valid precipitation sample involves careful attention to all aspects of the sampling and analysis process. Difficulties in obtaining low field blanks were experienced for a collector used in a project to determine precipitation inputs to Green Bay of Lake Michigan. The cause of high field blanks was found to be PCBs scavenged from the atmosphere and adsorbed on the Teflon™ surface of the sampler. These PCBs were extracted from the collector surface by the methanol used as a rinse solvent. The amounts of PCBs on the surface were found to be a factor of 20-50 higher than the amounts in a typical precipitation sample. After rinsing the Teflon surface several times with methanol, additional PCBs could be obtained by rinsing the surface with hexane or dichloromethane.

  1. Regional contamination versus regional dietary differences: Understanding geographic variation in brominated and chlorinated contaminant levels in polar bears

    Science.gov (United States)

    McKinney, M.A.; Letcher, R.J.; Aars, Jon; Born, E.W.; Branigan, M.; Dietz, R.; Evans, T.J.; Gabrielsen, G.W.; Muir, D.C.G.; Peacock, E.; Sonne, C.

    2011-01-01

    The relative contribution of regional contamination versus dietary differences to geographic variation in polar bear (Ursus maritimus) contaminant levels is unknown. Dietary variation between Alaska Canada, East Greenland, and Svalbard subpopulations was assessed by muscle nitrogen and carbon stable isotope (?? 15N, ?? 13C) and adipose fatty acid (FA) signatures relative to their main prey (ringed seals). Western and southern Hudson Bay signatures were characterized by depleted ?? 15N and ??13C, lower proportions of C20 and C22 monounsaturated FAs and higher proportions of C18 and longer chain polyunsaturated FAs. East Greenland and Svalbard signatures were reversed relative to Hudson Bay. Alaskan ?? 2011 American Chemical Society.

  2. Determination of platinum surface contamination in veterinary and human oncology centres using inductively coupled plasma mass spectrometry.

    Science.gov (United States)

    Janssens, T; Brouwers, E E M; de Vos, J P; de Vries, N; Schellens, J H M; Beijnen, J H

    2015-09-01

    The objective of this study was to determine the surface contamination with platinum-containing antineoplastic drugs in veterinary and human oncology centres. Inductively coupled plasma mass spectrometry was used to measure platinum levels in surface samples. In veterinary and human oncology centres, 46.3 and 68.9% of the sampled surfaces demonstrated platinum contamination, respectively. Highest platinum levels were found in the preparation rooms (44.6 pg cm(-2)) in veterinary centres, while maximal levels in human centres were found in oncology patient-only toilets (725 pg cm(-2)). Transference of platinum by workers outside areas where antineoplastic drugs were handled was observed in veterinary and human oncology centres. In conclusion, only low levels of platinum contamination attributable to carboplatin were found in the sampled veterinary oncology centres. However, dispersion of platinum outside areas where antineoplastic drugs were handled was detected in veterinary and human oncology centres. Consequently, not only personnel, but also others may be exposed to platinum. © 2013 Blackwell Publishing Ltd.

  3. Management of commercial high-level and transuranium-contaminated radioactive wastes. Environmental statement

    International Nuclear Information System (INIS)

    1974-09-01

    This Draft Environmental Statement is issued to assess the environmental impact of the AEC's program to manage commercial high-level and transuranium-contaminated radioactive wastes. These are the types of commercial radioactive wastes for which AEC custody is required by present or anticipated regulations. The program consists of three basic parts: development of a Retrievable Surface Storage Facility (RSSF) for commercial high-level waste, using existing technology; evaluating geological formations and sites for the development of a Geological Disposal Pilot Plant (GDPP) which would lead to permanent disposal; and providing retrievable storage for the transuranium-contaminated waste pending availability of permanent disposal. Consideration has been given to all environmental aspects of the program, using waste generation projections through the year 2000. Radiological and other impacts of implementing the program are expected to be minimal, but will be discussed in further environmental statements which will support budget actions for specific repositories. The alternatives discussed in this Draft Environmental Statement are presented. (U.S.)

  4. Bond strength of resin-resin interfaces contaminated with saliva and submitted to different surface treatments

    Directory of Open Access Journals (Sweden)

    Adilson Yoshio Furuse

    2007-12-01

    Full Text Available The purpose of this study was to investigate the effect of different surface treatments on shear bond strength of saliva-contaminated resin-resin interfaces. Flat resin surfaces were fabricated. In the control group, no contamination or surface treatment was performed. The resin surfaces of the experimental groups were contaminated with saliva and air-dried, and then submitted to: (G1 rinsing with water and drying; (G2 application of an adhesive system; (G3 rinsing and drying, abrasion with finishing disks, etching and application of adhesive system; (G4 rinsing and drying, etching, application of silane and adhesive system. Resin cylinders were placed over the treated surfaces. The specimens were stored in water or ethanol. Shear bond strength tests were performed and the mode of failure was evaluated. Data were submitted to two-way ANOVA and Dunnett T3 test. Contamination of resin-resin interfaces with saliva significantly reduced shear strength, especially after prolonged storage (p<0.05. Similar values to the original bond strength were obtained after abrasion and application of adhesive (G3 or etching and application of silane and adhesive (G4. If contamination occurs, a surface treatment is required to guarantee an adequate interaction between the resin increments.

  5. Geohydrology and susceptibility of major aquifers to surface contamination in Alabama, area 7

    Science.gov (United States)

    Mooty, W.S.

    1987-01-01

    The geohydrology and susceptibility of the seven major aquifers to surface contamination in Area 7 - Bibb, Dallas, Hale, Perry, and Wilcox Counties, are described. Aquifers in the northern part of the study area are in Paleozoic limestones and dolomite formations. Deposits in the central part of the study area are predominately of Cretaceous age and contain the Coker, Gordo, and Eutaw aquifers. Although the southern part of the study area has many deposits of Tertiary age, the Ripley Formation of Cretaceous age is the major aquifer. Contamination of any of the major aquifers is improbable because the majority of the recharge area for the primary aquifers is woodland, pasture, or farmland. Downdip from their outcrops, the major aquifers in the study area are protected from land surface contamination by relatively impermeable layers of clay and chalk. The aquifers that are highly susceptible to contamination are the ones in the limestone and dolomite formations in northern Bibb County. Sinkholes exist in the recharge area of these formations and could provide a direct link for contaminates from the land surface to the water table. An area northeast of the Selma well field is also highly susceptible to contamination. The Eutaw Formation in this area is overlain by alluvial deposits that could increase recharge to the aquifer by slowing the runoff rate of surface water. (USGS)

  6. Inactivation of internalized and surface contaminated enteric viruses in green onions.

    Science.gov (United States)

    Hirneisen, Kirsten A; Kniel, Kalmia E

    2013-09-02

    With increasing outbreaks of gastroenteritis associated with produce, it is important to assess interventions to reduce the risk of illness. UV, ozone and high pressure are non-thermal processing technologies that have potential to inactivate human pathogens on produce and allow the retention of fresh-like organoleptic properties. The objective of this study was to determine if UV, ozone, and high pressure are effective technologies compared to traditional chlorine spray on green onions to reduce enteric viral pathogens and to determine the effect of location of the virus (surface or internalized) on the efficacy of these processes. Mature green onion plants were inoculated with murine norovirus (MNV), hepatitis A virus (HAV) and human adenovirus type 41 (Ad41) either on the surface through spot inoculation or through inoculating contaminated hydroponic solution allowing for uptake of the virus into the internal tissues. Inoculated green onions were treated with UV (240 mJ s/cm(2)), ozone (6.25 ppm for 10 min), pressure (500 MPa, for 5 min at 20°C), or sprayed with calcium hypochlorite (150 ppm, 4°C). Viral inactivation was determined by comparing treated and untreated inoculated plants using cell culture infectivity assays. Processing treatments were observed to greatly affect viral inactivation. Viral inactivation for all three viruses was greatest after pressure treatment and the lowest inactivation was observed after chlorine and UV treatment. Both surface inoculated viruses and viruses internalized in green onions were inactivated to some extent by these post-harvest processing treatments. These results suggest that ozone and high pressure processes aimed to reduce the level of microbial contamination of produce have the ability to inactivate viruses if they become localized in the interior portions of produce. © 2013.

  7. Survival of foodborne pathogens on stainless steel surfaces and cross-contamination to foods

    NARCIS (Netherlands)

    Kusumaningrum, H.D.; Riboldi, G.; Hazeleger, W.C.; Beumer, R.R.

    2003-01-01

    The retention of bacteria on food contact surfaces increases the risk of cross-contamination of these microorganisms to food. The risk has been considered to be lowered when the surfaces are dry, partly because bacterial growth and survival would be reduced. However, some non-spore-forming bacteria

  8. Quantifying potential sources of surface water contamination with Campylobacter jejuni and Campylobacter coli

    NARCIS (Netherlands)

    Mughini-Gras, Lapo; Penny, Christian; Ragimbeau, Catherine; Schets, Franciska M.; Blaak, Hetty; Duim, Birgitta; Wagenaar, Jaap A.; Boer, de Albert; Cauchie, Henry-Michel; Mossong, Joel; Pelt, Van Wilfrid

    2016-01-01

    Campylobacter is the most common causative agent of human bacterial gastroenteritis and is frequently found in surface water, where it indicates recent contamination with animal faeces, sewage effluent, and agricultural run-off. The contribution of different animal reservoirs to surface water

  9. Fixation of soil surface contamination using natural polysaccharides

    Energy Technology Data Exchange (ETDEWEB)

    Sackschewsky, M.R.

    1993-09-01

    Natural polysaccharides were evaluated as alternatives to commercially available dust-control agents for application in buried-waste and contaminated-soil remediation situations. Materials were identified and evaluated with specific criteria in mind: the materials must be environmentally benign and must not introduce any additional hazardous materials; they must be effective for at least 2 or 3 days, but they do not necessarily have to be effective for more than 2 to 3 weeks; they should be relatively resistant to light traffic; they must not interfere with subsequent soil treatment techniques, especially soil washing; and they must be relatively inexpensive. Two products, a pregelled potato starch and a mixture of carbohydrates derived from sugar beets, were selected for evaluation. Testing included small- and large-scale field demonstrations, laboratory physical property analyses, and wind-tunnel evaluations.

  10. Fixation of soil surface contamination using natural polysaccharides

    International Nuclear Information System (INIS)

    Sackschewsky, M.R.

    1993-09-01

    Natural polysaccharides were evaluated as alternatives to commercially available dust-control agents for application in buried-waste and contaminated-soil remediation situations. Materials were identified and evaluated with specific criteria in mind: the materials must be environmentally benign and must not introduce any additional hazardous materials; they must be effective for at least 2 or 3 days, but they do not necessarily have to be effective for more than 2 to 3 weeks; they should be relatively resistant to light traffic; they must not interfere with subsequent soil treatment techniques, especially soil washing; and they must be relatively inexpensive. Two products, a pregelled potato starch and a mixture of carbohydrates derived from sugar beets, were selected for evaluation. Testing included small- and large-scale field demonstrations, laboratory physical property analyses, and wind-tunnel evaluations

  11. The Development of a Sub-Surface Monitoring System for Organic Contamination in Soils and Groundwater

    Directory of Open Access Journals (Sweden)

    Sharon L. Huntley

    2002-01-01

    Full Text Available A major problem when dealing with environmental contamination is the early detection and subsequent surveillance of the contamination. This paper describes the potential of sub-surface sensor technology for the early detection of organic contaminants in contaminated soils, sediments, and landfill sites. Rugged, low-power hydrocarbon sensors have been developed, along with a data-logging system, for the early detection of phase hydrocarbons in soil. Through laboratory-based evaluation, the ability of this system to monitor organic contamination in water-based systems is being evaluated. When used in conjunction with specific immunoassays, this can provide a sensitive and low-cost solution for long-term monitoring and analysis, applicable to a wide range of field applications.

  12. Two-pulse rapid remote surface contamination measurement.

    Energy Technology Data Exchange (ETDEWEB)

    Headrick, Jeffrey M.; Kulp, Thomas J.; Bisson, Scott E.; Reichardt, Thomas A.; Farrow, Roger L.

    2010-11-01

    This project demonstrated the feasibility of a 'pump-probe' optical detection method for standoff sensing of chemicals on surfaces. Such a measurement uses two optical pulses - one to remove the analyte (or a fragment of it) from the surface and the second to sense the removed material. As a particular example, this project targeted photofragmentation laser-induced fluorescence (PF-LIF) to detect of surface deposits of low-volatility chemical warfare agents (LVAs). Feasibility was demonstrated for four agent surrogates on eight realistic surfaces. Its sensitivity was established for measurements on concrete and aluminum. Extrapolations were made to demonstrate relevance to the needs of outside users. Several aspects of the surface PF-LIF physical mechanism were investigated and compared to that of vapor-phase measurements. The use of PF-LIF as a rapid screening tool to 'cue' more specific sensors was recommended. Its sensitivity was compared to that of Raman spectroscopy, which is both a potential 'confirmer' of PF-LIF 'hits' and is also a competing screening technology.

  13. Klebsiella sp. FIRD 2, a TBT-resistant bacterium isolated from contaminated surface sediment along Strait of Johor Malaysia.

    Science.gov (United States)

    Abubakar, Abdussamad; Mustafa, Muskhazli B; Johari, Wan Lutfi Wan; Zulkifli, Syaizwan Zahmir; Ismail, Ahmad; Mohamat-Yusuff, Ferdaus Binti

    2015-12-15

    A possible tributyltin (TBT)-degrading bacterium isolated from contaminated surface sediment was successfully identified as Klebsiella sp. FIRD 2. It was found to be the best isolate capable of resisting TBT at a concentration of 1000 μg L(-1). This was a concentration above the reported contaminated level at the sampling station, 790 μg L(-1). Further studies revealed that the isolate was Gram negative and resisted TBT concentrations of up to 1500 μg L(-1) in a Minimal Salt Broth without the addition of any carbon source within the first 48 h of incubation. It is expected that additional work could be conducted to check the degradation activity of this new isolate and possibly improve the degradation capacity in order to contribute to finding a safe and sustainable remediation solution of TBT contamination. Copyright © 2015 Elsevier Ltd. All rights reserved.

  14. Investigation on the level and movement of mercury contaminants around storage areas and food processing factories in Hassahesa town

    International Nuclear Information System (INIS)

    Abdelrahman, Nawal Ahmed Mohamed

    1999-11-01

    A total of 62 surface soil samples were taken from various sites in Hassahesa town and analyzed for total mercury level using x-ray fluorescence spectrometer. Sites were chosen to represent the soil of pesticide store, food processing factories (involved in using contaminated seeds as fuel), nera stock of redundant cotton seeds and neighbouring cotton fields. Control soils were sampled from similar soil type south Hassahesa town. The results indicated an elevated mercury level in all samples analyzed far exceeding the background and normal range for mercury in soil. The highest level of contamination was found in soil of pesticide store (51 ppm), followed by the two food factories (24 ppm and 19 ppm). Horizontal movement of mercury contaminants at various rates from foci of areas selected was noticed, wind direction and/or topography apparently had some role in this movement. The level of total mercury in the control soil was exceeding the background and normal range for mercury in soils reported from other places. Various aspects of levels of mercury contamination, their movements, transportation and toxicological impacts on various forms of life were discussed. (Author)

  15. Investigation on the level and movement of Mercury contaminants around storage areas and food processing factories in Hassahesa town, Sudan

    International Nuclear Information System (INIS)

    Abdelrahman, Nawal Ahmed Mohamed

    1999-11-01

    A total of 62 surface soil samples were taken from various sites in Hassahesa town and analyzed for total mercury level using X-ray fluorescence spectrometer. Sites were chosen to represent the soil of pesticide store, food processing factories (involved in using contaminated seeds as fuel), near stock of redundant cotton seeds and neighbouring cotton fields. Control soils were sampled from similar soil type south Hassahesa town. The results indicated an elevated mercury level in all samples analyzed far exceeding the background and normal range for mercury in soil. The highest level of contamination was found in soil of the pesticide store (51ppm), followed by the tow food factories (24 ppm and 19 ppm). Horizontal movement of mercury contaminants at various rates from foci of area selected was noticed, wind direction and/ or topography apparently had some role in this movement. The level of total mercury in the control soil was exceeding the background and normal range for mercury in soils reported from other places. Various aspects of levels of mercury contamination, their movements, transportation and toxicological impacts on various forms of life were discussed.(Author)

  16. Dispersion of inorganic contaminants in surface water in the vicinity of Potchefstroom

    Science.gov (United States)

    Manyatshe, A.; Fosso-Kankeu, E.; van der Berg, D.; Lemmer, N.; Waanders, F.; Tutu, H.

    2017-08-01

    Potchefstroom and the neighbouring cities rely mostly on the Mooi River and Vaal River for their water needs. These rivers flow through the gold mining areas and farms, and are therefore likely to be contaminated with substantial amounts of inorganic pollutants. Water was collected along the rivers network, streams, canals and dams in Potchefstroom and the vicinity. The samples were characterized for geochemical parameters, metals and anions concentrations. The results showed high concentrations of potentially toxic elements such as As (4.53 mg/L - 5.74 mg/L), Cd (0.25 mg/L - 0.7 mg/L), Pb (1.14 mg/L - 5.13 mg/L) and U (0.04 mg/L - 0.11 mg/L) which were predominantly found around the mining areas. Elevated concentrations of anions such SO42- and CN- were detected around mining areas while NO3- was dominant near farms. The relatively high levels of anions and metals in the surface water made it unfit for domestic or agricultural use. The study showed that contaminants in mining and agricultural facilities were potentially mobilised, thus impacting the nearby water systems.

  17. Modeling of Transmittance Degradation Caused by Optical Surface Contamination by Atomic Oxygen Reaction with Adsorbed Silicones

    Science.gov (United States)

    Snyder, Aaron; Banks, Bruce; Miller, Sharon; Stueber, Thomas; Sechkar, Edward

    2001-01-01

    A numerical procedure is presented to calculate transmittance degradation caused by contaminant films on spacecraft surfaces produced through the interaction of orbital atomic oxygen (AO) with volatile silicones and hydrocarbons from spacecraft components. In the model, contaminant accretion is dependent on the adsorption of species, depletion reactions due to gas-surface collisions, desorption, and surface reactions between AO and silicone producing SiO(x), (where x is near 2). A detailed description of the procedure used to calculate the constituents of the contaminant layer is presented, including the equations that govern the evolution of fractional coverage by specie type. As an illustrative example of film growth, calculation results using a prototype code that calculates the evolution of surface coverage by specie type is presented and discussed. An example of the transmittance degradation caused by surface interaction of AO with deposited contaminant is presented for the case of exponentially decaying contaminant flux. These examples are performed using hypothetical values for the process parameters.

  18. OPERATIONAL LIMITATIONS FOR DEMOLITION OF A HIGHLY ALPHA CONTAMINATED BUILDING MODLES VERSUS MEASURED AIR & SURFACE ACTIVITY CONCENTRATIONS

    Energy Technology Data Exchange (ETDEWEB)

    LLOYD, E.R.

    2006-11-02

    The demolition of a facility historically used for processing and handling transuranic materials is considered. Residual alpha emitting radionuclide contamination poses an exposure hazard if released to the local environment during the demolition. The process of planning for the demolition of this highly alpha contaminated building, 232-Z, included a predemolition modeling analysis of potential exposures. Estimated emission rates were used as input to an air dispersion model to estimate frequencies of occurrence of peak air and surface exposures. Postdemolition modeling was also conducted, based on the actual demolition schedule and conditions. The modeling results indicated that downwind deposition is the main operational limitation for demolition of a highly alpha-contaminated building. During the demolition of 232-Z, airborne radiation and surface contamination were monitored. The resultant non-detect monitoring results indicate a significant level of conservatism in the modeled results. This comparison supports the use of more realistic assumption in the estimating emission rates. The resultant reduction in modeled levels of potential exposures has significant implications in terms of the projected costs of demolition of such structures.

  19. OPERATIONAL LIMITATIONS FOR DEMOLITION OF A HIGHLY ALPHA-CONTAMINATED BUILDING- MODELED VERSUS MEASURED AIR and SURFACE ACTIVITY CONCENTRATIONS

    International Nuclear Information System (INIS)

    LLOYD, E.R.

    2006-01-01

    The demolition of a facility historically used for processing and handling transuranic materials is considered. Residual alpha emitting radionuclide contamination poses an exposure hazard if released to the local environment during the demolition. The process of planning for the demolition of this highly alpha contaminated building, 232-Z, included a predemolition modeling analysis of potential exposures. Estimated emission rates were used as input to an air dispersion model to estimate frequencies of occurrence of peak air and surface exposures. Postdemolition modeling was also conducted, based on the actual demolition schedule and conditions. The modeling results indicated that downwind deposition is the main operational limitation for demolition of a highly alpha-contaminated building. During the demolition of 232-Z, airborne radiation and surface contamination were monitored. The resultant non-detect monitoring results indicate a significant level of conservatism in the modeled results. This comparison supports the use of more realistic assumption in the estimating emission rates. The resultant reduction in modeled levels of potential exposures has significant implications in terms of the projected costs of demolition of such structures

  20. Surface sterilization method for reducing microbial contamination of ...

    African Journals Online (AJOL)

    An effective disinfection method for strawberry (Fragaria x ananassa Duch.) cv. Senga Sengana micropropagation using runner tips and nodal segments as explants was developed. The explants were surface sterilized with different sterilants for different durations. The present studies on the effect of different regimes of ...

  1. Investigation of Polyaniline and a Functionalised Derivative as Antimicrobial Additives to Create Contamination Resistant Surfaces

    Directory of Open Access Journals (Sweden)

    Julia Robertson

    2018-03-01

    Full Text Available Antimicrobial surfaces can be applied to break transmission pathways in hospitals. Polyaniline (PANI and poly(3-aminobenzoic acid (P3ABA are novel antimicrobial agents with potential as non-leaching additives to provide contamination resistant surfaces. The activity of PANI and P3ABA were investigated in suspension and as part of absorbent and non-absorbent surfaces. The effect of inoculum size and the presence of organic matter on surface activity was determined. PANI and P3ABA both demonstrated bactericidal activity against Escherichia coli and Staphylococcus aureus in suspension and as part of an absorbent surface. Only P3ABA showed antimicrobial activity in non-absorbent films. The results that are presented in this work support the use of P3ABA to create contamination resistant surfaces.

  2. Microbial contamination level of air in animal waste utilization plants.

    Science.gov (United States)

    Chmielowiec-Korzeniowska, Anna; Tymczyna, Leszek; Drabik, Agata; Krzosek, Łukasz

    2016-01-01

    The aim of this research was evaluation of microbial contamination of air within and in the vicinity of animal waste disposal plants. Air samples were analyzed to determine total bacterial and fungal counts as well as microbial species composition. Measurements of climate conditions (temperature, humidity, air motion) and total dust concentration were also performed. Total numbers of bacteria and fungi surpassed the threshold limit values for production halls. The most abundant bacteria detected were those consisting of physiological microflora of animal dermis and mucosa. Fungal species composition proved to be most differentiated in the air beyond the plant area. Aspergillus versicolor, a pathogenic and allergenic filamentous fungus, was isolated only inside the rendering plant processing hall. The measurement results showed a low sanitary-hygienic state of air in the plant processing halls and substantial air pollution in its immediate vicinity.

  3. The development of the American national standard, ''control of radioactive surface contamination on materials, equipment and facilities to be released for uncontrolled use''

    International Nuclear Information System (INIS)

    Shapiro, J.

    1980-01-01

    The American National Standard, Control of Radioactive Surface Contamination on Materials, Equipment and Facilities to be Released for Uncontrolled Use, was developed under the procedures of ANSI for ANSI Main Committee N13 (Radiation Protection) by a working group of the Health Physics Society Standards Committee. This standard provides criteria for the control of materials, equipment and facilities contaminated with radioactivity proposed to be released for uncontrolled use. Permissible contamination limits are specified as well as methods assessing the levels of contamination. This paper reviews the proceedings of the Subcommittee on Radioactive Surface Contamination, the comments received by reviewers of the standard, the resolution of the committee, and the bases for reaching the final limits, recommendations, and measurement procedures. (H.K.)

  4. Global occurrence of anti-infectives in contaminated surface waters: Impact of income inequality between countries.

    Science.gov (United States)

    Segura, Pedro A; Takada, Hideshige; Correa, José A; El Saadi, Karim; Koike, Tatsuya; Onwona-Agyeman, Siaw; Ofosu-Anim, John; Sabi, Edward Benjamin; Wasonga, Oliver V; Mghalu, Joseph M; dos Santos Junior, Antonio Manuel; Newman, Brent; Weerts, Steven; Yargeau, Viviane

    2015-07-01

    The presence anti-infectives in environmental waters is of interest because of their potential role in the dissemination of anti-infective resistance in bacteria and other harmful effects on non-target species such as algae and shellfish. Since no information on global trends regarding the contamination caused by these bioactive substances is yet available, we decided to investigate the impact of income inequality between countries on the occurrence of anti-infectives in surface waters. In order to perform such study, we gathered concentration values reported in the peer-reviewed literature between 1998 and 2014 and built a database. To fill the gap of knowledge on occurrence of anti-infectives in African countries, we also collected 61 surface water samples from Ghana, Kenya, Mozambique and South Africa, and measured concentrations of 19 anti-infectives. A mixed one-way analysis of covariance (ANCOVA) model, followed by Turkey-Kramer post hoc tests was used to identify potential differences in anti-infective occurrence between countries grouped by income level (high, upper-middle and lower-middle and low income) according to the classification by the World Bank. Comparison of occurrence of anti-infectives according to income level revealed that concentrations of these substances in contaminated surface waters were significantly higher in low and lower-middle income countries (p=0.0001) but not in upper-middle income countries (p=0.0515) compared to high-income countries. We explained these results as the consequence of the absence of or limited sewage treatment performed in lower income countries. Furthermore, comparison of concentrations of low cost anti-infectives (sulfonamides and trimethoprim) and the more expensive macrolides between income groups suggest that the cost of these substances may have an impact on their environmental occurrence in lower income countries. Since wastewaters are the most important source of contamination of anti-infectives and other

  5. Examination of background contamination levels for gas counting and AMS target preparation in Trondheim

    DEFF Research Database (Denmark)

    Gulliksen, S.; Thomsen, M.S.

    1992-01-01

    conventional gas proportional counting (GPC) system. We have also studied contamination levels of our target preparation for C-14 accelerator mass spectrometry (AMS) dating in Uppsala. A significant lower background is obtained for Icelandic double spar than for marbles, probably due to a crystal structure......The Radiological Dating Laboratory in Trondheim relatively often dates samples with ages >30 ka BP. Contaminated background materials are known to affect the accuracy of very old dates. We have found, by measurements of different materials, that such contamination is small when using our...... of the double spar that is more insensitive to contaminating processes. The background for combusted samples is at the same level as for samples of double spar, indicating that additional C-14 contamination due to combustion is negligible. Dates obtained on interstadial samples (T >30 ka BP) by both GPC and AMS...

  6. Integrated modelling for assessing the risk of groundwater contaminants to human health and surface water ecosystems

    DEFF Research Database (Denmark)

    McKnight, Ursula S.; Rasmussen, Jes; Funder, Simon G.

    2010-01-01

    of contamination. In particular, adaptive management tools designed to work with sparse data sets from preliminary site assessments are needed which can explicitly link contaminant point sources with groundwater, surface water and ecological impacts. Here, a novel integrated modelling approach was employed...... volatilisation model for the stream. The model is tested on a Danish case study involving a 750 m long TCE groundwater plume discharging into a stream. The initial modelling results indicate that TCE contaminant plumes with μgL-1 concentrations entering surface water systems do not pose a significant risk...... for evaluating the impact of a TCE groundwater plume, located in an area with protected drinking water interests, to human health and surface water ecosystems. This is accomplished by coupling the system dynamicsbased decision support system CARO-Plus to the aquatic ecosystem model AQUATOX via an analytical...

  7. Real-Time PCR Detection ofBurkholderia cepaciain Pharmaceutical Products Contaminated with Low Levels of Bacterial Contamination.

    Science.gov (United States)

    Jimenez, Luis; Jashari, Theranda; Vasquez, Jenifer; Zapata, Stephanie; Bochis, Joy; Kulko, Margarita; Ellman, Victoria; Gardner, Matthew; Choe, Tina

    2018-01-01

    A real-time polymerase chain reaction (RT-PCR) assay was developed to detect Burkholderia cepacia in pharmaceutical products contaminated with low levels of bacteria. Different pharmaceutical suspensions were artificially contaminated with B. cepacia , Escherichia coli , Staphylococcus aureus , and Bacillus megaterium After a 24 h incubation in trypticase soy broth with Tween 20, samples were streaked on mannitol salt, phenyl ethyl alcohol, eosin methylene blue, MacConkey, and pseudomonas isolation agar. Microbial DNA was extracted from each sample by using a Tris-EDTA, proteinase K, Tween 20 buffer. Regular PCR targeting the 1.5 kilobases 16S rRNA eubacterial gene and cloning showed the predominant DNA in the extracted mix belonged to E. coli Selective media isolation of bacterial contamination showed B. cepacia only detected on pseudomonas isolation while eosin methylene blue and MacConkey detected only E. coli RT-PCR using primers PSL1 and PSR1 amplified a 209 bp 16S rRNA fragment using a Roche LightCycler 96 ® system with SYBR green I, a common double-stranded binding dye. The cycle at which fluorescence from amplification exceeds the background fluorescence was referred to as quantification cycle. All samples were found to be positive by standard microbiological testing and RT-PCR. B. cepacia was detected within 30 h in all contaminated samples using RT-PCR. Based upon standard curve analysis of B. cepacia DNA, the minimum DNA concentration that could be detected was 10 fg/uL with a correlation value of 0.98. RT-PCR detection of B. cepacia allowed faster quality control analysis, corrective actions, and process optimization. LAY ABSTRACT: A real-time polymerase chain reaction (RT-PCR) assay was developed to detect Burkholderia cepacia in pharmaceutical products contaminated with low levels of bacteria. B. cepacia is the number one reason for microbial contamination recalls of non-sterile drug products in the USA. RT-PCR using primers PSL1 and PSR1 amplified a

  8. Effects of surface contamination and cleaning with hypochlorite wipes on the antibacterial activity of copper-alloyed antibacterial stainless steel.

    Science.gov (United States)

    Kawakami, Hiroshi; Hayashi, Takatsuna; Nishikubo, Hideyuki; Morikawa, Akifumi; Suzuki, Satoshi; Sato, Yoshihiro; Kikuchi, Yasushi

    2014-01-01

    Effects of surface contamination and cleaning with hypochlorite wipes on the antibacterial activity of copper-alloyed stainless steel were studied. The antibacterial activity of copper alloyed stainless steel decreased with the increase in the amount of surface contaminant, and the bacterial counts from specimens contaminated with a contaminant, e.g. 1.6 × 10(-2) μg/mm(2) of bovine serum albumin, were not significantly different from those from ordinary stainless steel specimens. The once contaminated surface could regain its antibacterial activity when it was sufficiently wiped clean with sterile wipes loaded with sodium hypochlorite solution.

  9. Development of the automatic measuring system to survey the surface contamination on equipments

    International Nuclear Information System (INIS)

    Ishizuka, Akira; Matsumura, Hidekatsu; Nawa, Takao; Yamaguchi, Seiji; Yamada, Tadashi.

    1980-01-01

    The inspection of surface contamination carried out when things are taken out of the control areas in nuclear power stations requires considerable labor and time because it is carried out manually. In order to make the inspection of surface contamination more efficiently and to standardize it, the development of an automatic inspection apparatus was carried out. This apparatus inspects the surface contamination due to radio isotopes which do not emit α-ray, and the objects to be measured are the large things with definite forms, such as boards and pipes for scaffolding. The method of measuring β-ray with a gas flow counter was adopted for the apparatus in view of the good detection sensitivity, relatively simple shielding against background, and easy conversion to surface contamination density. The measuring system was composed of the gas flow counters and a rate meter. The outline of the apparatus made for trial is explained. As the result of the performance test, the lowest detection sensitivity was 1.29 x 10 -5 μCi/cm 2 at the moving speed of an object of 1 cm/sec. The detection sensitivity is improved by the flattening of the sensitivity distribution. The evaluation of the error, the reduction of measuring time and the prevention of contamination were also made. (Kako, I.)

  10. Secondary radioactive contamination of the Black Sea after Chernobyl accident: recent levels, pathways and trends.

    Science.gov (United States)

    Gulin, S B; Mirzoyeva, N Yu; Egorov, V N; Polikarpov, G G; Sidorov, I G; Proskurnin, V Yu

    2013-10-01

    The recent radionuclide measurements have showed that concentrations of the Chernobyl-derived (137)Cs and (90)Sr in the surface Black Sea waters are still relatively high, reaching 56 and 32 Bq m(-3), respectively. This is comparable or even exceeds the pre-Chernobyl levels (∼16 Bq (137)Cs and 22 Bq (90)Sr per m(3) as the basin-wide average values). The measurements have revealed that the Black Sea continues to receive Chernobyl radionuclides, particularly (90)Sr, by the runoff from the Dnieper River. An additional source of (90)Sr and (137)Cs was found in the area adjacent to the Kerch Strait that connects the Black Sea and the Sea of Azov. This may be caused by the inflow of the contaminated Dnieper waters, which come to this area through the North-Crimean Canal. The long-term monitoring of (137)Cs and (90)Sr concentration in the Black Sea surface waters and in the benthic brown seaweed Cystoseira sp., in comparison with the earlier published sediment records of the radionuclides, have showed signs of a secondary radioactive contamination, which has started to increase since the late 1990's. This may be the result of the combined effect of a higher input of radionuclides from the rivers in 1995-1999 due to an increased runoff; and a slow transport of the particulate bound radionuclides from the watersheds followed by their desorption in seawater from the riverine suspended matter and remobilization from the sediments adjacent to the river mouths. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. Derived surface contamination limits for the uranium mining and milling industry

    International Nuclear Information System (INIS)

    Ching, S.H.

    1984-10-01

    Derived Surface Contamination Limits (DSCL) are proposed for the control of surface contamination at the work place for the uranium mining and milling industry. They have been derived by a method incorporating recent ICRP recommendations and consideration of the radiation exposure pathways of ingestion, inhalation and external irradiation of the basal layer of skin. A generalized DSCL of 10 5 Bq/m 2 of beta activity is recommended for all contaminants likely to be found in uranium mine and mill workplaces except for fresh uranium concentrates. In the latter case, the DSCL is expressed in terms of alpha activity because the ratio of beta to alpha activities for fresh uranium concentrates is variable; the beta activity increases with the ingrowth of U-238 daughter products (Th-234 and Pa-234m) until secular equilibrium is re-established in about six months. A surface contamination limit of 10 4 Bq/m 2 of beta activity is proposed for the release of non-porous materials and equipment with no detectable loose contamination to the public domain

  12. Optimization of the allowed levels of radioactive contamination on a virtual market of polluted provisions

    International Nuclear Information System (INIS)

    Frantsevich, L.Yi.

    1997-01-01

    The goal is to optimize the allowed levels of 137 Cs contamination of food products according to the ALARA principle. The model creates a virtual market of contaminated daily portions of various products, their contamination being distributed log normally with the same parameters as in real products. The consumer requests portions and wasters contaminated until one obtains 365 acceptable portions of every product per year. The cost of wastering is high at a low allowed level. The floating price of irradiation depends on the yearly consumption of 137 Cs and is stated very high when the last value approaches the dose limit (risk aversive function). Varying allowed levels, it is possible to minimize the cost of wastering and total cost of wastering and irradiation. The iterative algorithm is proposed

  13. ASSESSMENT OF RADIOACTIVE AND NON-RADIOACTIVE CONTAMINANTS FOUND IN LOW LEVEL RADIOACTIVE WASTE STREAMS

    International Nuclear Information System (INIS)

    R.H. Little, P.R. Maul, J.S.S. Penfoldag

    2003-01-01

    This paper describes and presents the findings from two studies undertaken for the European Commission to assess the long-term impact upon the environment and human health of non-radioactive contaminants found in various low level radioactive waste streams. The initial study investigated the application of safety assessment approaches developed for radioactive contaminants to the assessment of nonradioactive contaminants in low level radioactive waste. It demonstrated how disposal limits could be derived for a range of non-radioactive contaminants and generic disposal facilities. The follow-up study used the same approach but undertook more detailed, disposal system specific calculations, assessing the impacts of both the non-radioactive and radioactive contaminants. The calculations undertaken indicated that it is prudent to consider non-radioactive, as well as radioactive contaminants, when assessing the impacts of low level radioactive waste disposal. For some waste streams with relatively low concentrations of radionuclides, the potential post-closure disposal impacts from non-radioactive contaminants can be comparable with the potential radiological impacts. For such waste streams there is therefore an added incentive to explore options for recycling the materials involved wherever possible

  14. Experimental analysis on removal factor of smear method in measurement of surface contamination

    International Nuclear Information System (INIS)

    Sugiura, Nobuyuki; Taira, Junichi; Takenaka, Keisuke; Yamanaka, Kazuo; Sugai, Kenji; Kosako, Toshiso

    2007-01-01

    The smear test is one of the important ways to measure surface contamination. The loose contamination under the high background radiation, which is more significant in handling non-sealed radioisotopes, can be evaluated by this method. The removal factor is defined as the ratio of the activity removed from the surface by one smear to the whole activity of the removable surface contamination. The removal factor is greatly changed by the quality and condition of surface materials. In this study, the values of removal factor at several typical surface conditions were evaluated experimentally and the practical application of those values was considered. It is required the smear should be pressed by moderate pressure when wiping the surface. The pressure from 1.0 kg to 1.5 kg per filter paper was recommended. The removal factor showed lower value in wiping by the pressure below 1.0 kg. The value of 0.5 for the removal factor could be applied to the smooth surface of linoleum, concrete coated with paint or epoxy resin, stainless steel and glass with the statistical allowance. (author)

  15. Measurement of underground contamination of non-aqueous phase liquids (NAPLs) on the basis of the radon concentration in ground level air

    International Nuclear Information System (INIS)

    Schubert, M.

    2001-01-01

    It was investigated whether measurements of radon concentrations in ground level air are a suitable method of detecting sub-surface soil contamination with non-aqueous phase liquids (NAPLs). The working postulation was that, due to the very high solubility of radon in NAPLs, and the resulting accumulation of radon in NAPLs, radon exhalation to the ground level air in the proximity of such NAPL contamination should be locally reduced, thus indicating contamination of sub-surface soils with NAPLs. The research work reported was to verify the working theory by way of experiments, and to finally develop a reliable detection method for NAPL contaminations. The investigations comprised theoretical studies, laboratory experiments, experiments in defined soil columns, and extensive field studies [de

  16. Surface contamination of counting tools after mock dispensing of cyclophosphamide in a simulated outpatient pharmacy.

    Science.gov (United States)

    Chaffee, Bruce W; Lander, Michael J; Christen, Catherine; Redic, Kimberly A

    2018-01-01

    Purpose The primary aim was to determine if dispensing of cyclophosphamide tablets resulted in accumulated residue on pharmacy counting tools during a simulated outpatient dispensing process. Secondary objectives included determining if cyclophosphamide contamination exceeded a defined threshold level of 1 ng/cm 2 and if a larger number of prescriptions dispensed resulted in increased contamination. Methods Mock prescriptions of 40 cyclophosphamide 50 mg tablets were counted on clean trays in three scenarios using a simulated outpatient pharmacy after assaying five cleaned trays as controls. The three scenarios consisted of five simulated dispensings of one, three, or six prescriptions dispensed per scenario. Wipe samples of trays and spatulas were collected and assayed for all trays, including the five clean trays used as controls. Contamination was defined as an assayed cyclophosphamide level at or above 0.001 ng/cm 2 and levels above 1 ng/cm 2 were considered sufficient to cause risk of human uptake. Mean contamination for each scenario was calculated and compared using one-way analysis of variance. P-values of contamination on trays used to count one, three, and six cyclophosphamide prescriptions was 0.51 ± 0.10 (p=0.0003), 1.02 ± 0.10 (p contamination. Increasing the number of prescriptions dispensed from 1 to 3, 1 to 6, and 3 to 6 counts increased contamination by 0.51 ± 0.15 (p = 0.0140), 1.31 + 0.15 (p contaminates pharmacy counting tools, and an increased number of prescriptions dispensed correlates with increased level of contamination. Counting out three or more prescriptions leads to trays having contamination that surpasses the threshold at which worker exposure may be increased. Pharmacies should consider devoting a separate tray to cyclophosphamide tablets, as cross-contamination could occur with other drugs and the efficacy of decontamination methods is unclear. Employee exposure could be minimized with the use

  17. Contamination of environmental surfaces by methicillin-resistant Staphylococcus aureus (MRSA) in rooms of inpatients with MRSA-positive body sites.

    Science.gov (United States)

    Kurashige, E Jessica Ohashi; Oie, Shigeharu; Furukawa, H

    2016-01-01

    Methicillin-resistant Staphylococcus aureus (MRSA) can contaminate environmental surfaces that are frequently touched by the hands of patients with MRSA colonization/infection. There have been many studies in which the presence or absence of MRSA contamination was determined but no studies in which MRSA contamination levels were also evaluated in detail. We evaluated MRSA contamination of environmental surfaces (overbed tables, bed side rails, and curtains) in the rooms of inpatients from whom MRSA was isolated via clinical specimens. We examined the curtains within 7-14 days after they had been newly hung. The environmental surfaces were wiped using gauze (molded gauze for wiping of surface bacteria; 100% cotton, 4cm×8cm) moistened with sterile physiological saline. The MRSA contamination rate and mean counts (range) were 25.0% (6/24 samples) and 30.6 (0-255)colony-forming units (cfu)/100cm(2), respectively, for the overbed tables and 31.6% (6/19 samples) and 159.5 (0-1620)cfu/100cm(2), respectively, for the bed side rails. No MRSA was detected in 24 curtain samples. The rate of MRSA contamination of environmental surfaces was high for the overbed tables and bed side rails but low for the curtains. Therefore, at least until the 14th day of use, frequent disinfection of curtains may be not necessary. Copyright © 2016. Published by Elsevier Editora Ltda.

  18. Effectiveness of disinfection with alcohol 70% (w/v) of contaminated surfaces not previously cleaned

    OpenAIRE

    Graziano, Maurício Uchikawa; Graziano, Kazuko Uchikawa; Pinto, Flávia Morais Gomes; Bruna, Camila Quartim de Moraes; Souza, Rafael Queiroz de; Lascala, Cesar Angelo

    2013-01-01

    OBJECTIVE: To evaluate the disinfectant effectiveness of alcohol 70% (w/v) using friction, without previous cleaning, on work surfaces, as a concurrent disinfecting procedure in Health Services. METHOD: An experimental, randomized and single-blinded laboratory study was undertaken. The samples were enamelled surfaces, intentionally contaminated with Serratia marcescens microorganisms ATCC 14756 106 CFU/mL with 10% of human saliva added, and were submitted to the procedure of disinfection W...

  19. Investigation of the pathway of contaminated soil transported to plant surfaces by raindrop splash

    International Nuclear Information System (INIS)

    Dreicer, M.; Hakonson, T.E.; Whicker, F.W.; White, G.C.

    1983-01-01

    The environmental transport pathway of soil-borne radioisotopes to vegetation surfaces via raindrop splash was studied. The data show that soil can significantly contribute to the contamination found on plants. Further detailed study is needed to calculate the rate constant for the raindrop splash and retention pathways. 8 references, 1 figure

  20. Cold plasma rapid decontamination of food contact surfaces contaminated with Salmonella biofilms

    Science.gov (United States)

    Cross-contamination of fresh produce and other foods from persistent pathogen reservoirs is a known risk factor in processing environments. Industry requires a rapid, waterless, zero-contact, chemical-free method for removing pathogens from food-contact surfaces. Cold plasma was tested for its abili...

  1. Bond strength of resin-resin interfaces contaminated with saliva and submitted to different surface treatments

    DEFF Research Database (Denmark)

    Furuse, Adilson Yoshio; da Cunha, Leonardo Fernandes; Benetti, Ana Raquel

    2007-01-01

    of silane and adhesive system. Resin cylinders were placed over the treated surfaces. The specimens were stored in water or ethanol. Shear bond strength tests were performed and the mode of failure was evaluated. Data were submitted to two-way ANOVA and Dunnett T3 test. Contamination of resin...

  2. A new technique for the identification of surface contamination in low temperature bolometric experiments

    International Nuclear Information System (INIS)

    Sangiorgio, S.; Arnaboldi, C.; Brofferio, C.; Bucci, C.; Capelli, S.; Carbone, L.; Clemenza, M.; Cremonesi, O.; Fiorini, E.; Foggetta, L.; Giuliani, A.; Gorla, P.; Nones, C.; Nucciotti, A.; Pavan, M.; Pedretti, M.; Pessina, G.; Pirro, S.; Previtali, E.; Salvioni, C.

    2011-01-01

    In the framework of the bolometric experiment CUORE, a new and promising technique has been developed in order to control the dangerous contamination coming from the surfaces close to the detector. In fact, by means of a composite bolometer, it is possible to partially overcome the loss of spatial resolution of the bolometer itself and to clearly identify events coming from outside.

  3. Aluminum-contaminant transport by surface runoff and bypass flow from an acid sulphate soil

    NARCIS (Netherlands)

    Minh, L.Q.; Tuong, T.P.; Mensvoort, van M.E.F.; Bouma, J.

    2002-01-01

    Quantifying the process and the amount of acid-contaminant released to the surroundings is important in assessing the environmental hazards associated with reclaiming acid sulphate soils (ASS). The roles of surface runoff and bypass flow (i.e. the rapid downward flow of free water along macropores

  4. ASSESSMENTOF BETA PARTICLE FLUX FROM SURFACE CONTAMINATION AS A RELATIVE INDICATOR FOR RADIONUCLIDE DISTRIBUTION ON EXTERNAL SURFACES OF A MULTI-STORY BUILDING IN PRIPYAT

    Energy Technology Data Exchange (ETDEWEB)

    Farfan, E.

    2009-11-17

    How would we recover if a Radiological Dispersion Device (e.g., dirty bomb) or Improvised Nuclear Device were to detonate in a large city? In order to assess the feasibility of remediation following such an event, several issues would have to be considered, including the levels and characteristics of the radioactive contamination, the availability of the required resources to accomplish decontamination, and the planned future use of the city's structures and buildings. Presently little is known about the distribution, redistribution, and migration of radionuclides in an urban environment. However, Pripyat, a city substantially contaminated by the Chernobyl Nuclear Power Plant accident, may provide some answers. The main objective of this study was to determine the radionuclide distribution on a Pripyat multi-story building, which had not been previously decontaminated and therefore could reflect the initial fallout and its further natural redistribution on external surfaces. The 7-story building selected was surveyed from the ground floor to the roof on horizontal and vertical surfaces along seven ground-to-roof transections. Some of the results from this study indicate that the upper floors of the building had higher contamination levels than the lower floors. The authors consequently recommend that existing decontamination procedures for tall structures be re-examined and modified accordingly.

  5. Krypton 85 in the atmosphere: contamination levels in the years 1950-80

    International Nuclear Information System (INIS)

    Dvorak, Z.; Wilhelmova, L.

    1984-01-01

    The mean zonal 85 Kr contamination level of the ground layer of the troposphere was estimated for the mild climatic zone of the northern hemisphere using an induction technique. For data processing the values of short-term local effects were eliminated using the method of mathematical statistics. Long-term local effects were eliminated using the method of diffusion analysis based on the assumption of zonal homogeneity of global contamination of the atmosphere with 85 Kr. The results of statistical processing are summed up in the table. The diagram shows that the increase in atmospheric contamination with 85 Kr is not monotonous. (E.S.)

  6. Prevalence and contamination levels of listeria monocytogenes in ready-to-eat foods in Tokyo, Japan.

    Science.gov (United States)

    Shimojima, Yukako; Ida, Miki; Nakama, Akiko; Nishino, Yukari; Fukui, Rie; Kuroda, Sumiyo; Hirai, Akihiko; Kai, Akemi; Sadamasu, Kenji

    2016-08-01

    We surveyed prevalence and contamination levels of Listeria monocytogenes in ready-to-eat foods between 2000 and 2012 in Tokyo. L. monocytogenes was isolated from 52 (1.7%) out of 2,980 samples. Comparing the prevalence in the study period, 2.2% were positive in the former period (2000-2005) and 1.2% in the latter (2006-2012). Using the most probable number (MPN) technique, 32 samples were contaminated with fewer than 0.3 L. monocytogenes/g, 10 samples with 0.3-1.0/g and 4 samples with more than 1.0/g (the maximum was 2.3/g). The most common serovar was 1/2a, followed by 1/2b, 4b and 1/2c. We revealed that ready-to-eat foods in Tokyo were contaminated with L. monocytogenes, although the contamination levels were low.

  7. SCO shipments from Rocky Flats - Experience and current practice [Surface Contaminated Object

    International Nuclear Information System (INIS)

    Bracken, Gary; Morris, Robert L.

    2001-01-01

    Decommissioning activities at Rocky Flats Environmental Technology Site (RFETS) are expected to generate approximately 251,000 cubic meters of low-level radioactive waste. Almost half of this will be characterized and shipped as the Department of Transportation ''Surface Contaminated Object'' (SCO) shipping class. In the 2 years since an SCO characterization method was implemented, almost 11,000 of the 18,000 cubic meters of low-level waste were SCO. RFETS experience to-date using an SCO waste characterization method has shown significant time and cost savings, reduced errors, and enhanced employee safety. SCO waste is characterized prior to packaging, near the point of generation, by any of the site's 300 Radiological Control Technicians using inexpensive radiological control survey instruments. This reduces on-site waste container moves and eliminates radiometric analysis at centrally located drum or crate counters. Containers too large for crate counters can also be characterized. Current instrumentation is not adequate to take full advantage of the SCO regulations. Future improvements in the SCO characterization and shipping process are focused on use of larger and/or reusable containers, extended-range instruments, and additional statistical methods, so that the full extent of the SCO regulations can be used

  8. TECHNICAL BASIS FOR EVALUATING SURFACE BARRIERS TO PROTECT GROUNDWATER FROM DEEP VADOSE ZONE CONTAMINATION

    International Nuclear Information System (INIS)

    Fayer, J.M.; Freedman, V.L.; Ward, A.L.; Chronister, G.B.

    2010-01-01

    The U.S. DOE and its predecessors released nearly 2 trillion liters (450 billion gallons) of contaminated liquid into the vadose zone at the Hanford Site. Some of the contaminants currently reside in the deeper parts of the vadose zone where they are much less accessible to characterization, monitoring, and typical remediation activities. The DOE Richland Operations Office (DOE-RL) prepared a treatability test plan in 2008 to examine remediation options for addressing contaminants in the deep vadose zone; one of the technologies identified was surface barriers (also known as engineered barriers, covers, and caps). In the typical configuration, the contaminants are located relatively close to the surface, generally within 15 m, and thus they are close to the base of the surface barrier. The proximity of the surface barrier under these conditions yielded few concerns about the effectiveness of the barrier at depth, particularly for cases in which the contaminants were in a lined facility. At Hanford, however, some unlined sites have contaminants located well below depths of 15 m. The issue raised about these sites is the degree of effectiveness of a surface barrier in isolating contaminants in the deep vadose zone. Previous studies by Hanford Site and PNNL researchers suggest that surface barriers have the potential to provide a significant degree of isolation of deep vadose zone contaminants. The studies show that the actual degree of isolation is site-specific and depends on many factors, including recharge rates, barrier size, depth of contaminants, geohydrologic properties ofthe sediments, and the geochemical interactions between the contaminants and the sediments. After the DOE-RL treatability test plan was published, Pacific Northwest National Laboratory was contracted to review the information available to support surface barrier evaluation for the deep vadose zone, identify gaps in the information and outcomes necessary to fill the data gaps, and outline

  9. Methodology for determining acceptable residual radioactive contamination levels at decommissioned nuclear facilities/sites

    International Nuclear Information System (INIS)

    Watson, E.C.; Kennedy, W.E. Jr.; Hoenes, G.R.; Waite, D.A.

    1979-01-01

    The ultimate disposition of decommissioned nuclear facilities and their surrrounding sites depends upon the degree and type of residual contamination. Examination of existing guidelines and regulations has led to the conclusion that there is a need for a general method to derive residual radioactive contamination levels that are acceptable for public use of any decommissioned nuclear facility or site. This paper describes a methodology for determining acceptable residual radioactive contamination levels based on the concept of limiting the annual dose to members of the public. It is not the purpose of this paper to recommend or even propose dose limits for the exposure of the public to residual radioactive contamination left at decommissioned nuclear facilities or sites. Unrestricted release of facilities and/or land is based on the premise that the potential annual dose to any member of the public using this property from all possible exposure pathways will not exceed appropriate limits as may be defined by Federal regulatory agencies. For decommissioned land areas, consideration should be given to people living directly on previously contaminated areas, growing crops, grazing food animals and using well water. Mixtures of radionuclides in the residual contamination representative of fuel reprocessing plants, light water reactors and their respective sites are presented. These mixtures are then used to demonstrate the methodology. Example acceptable residual radioactive contamination levels, based on an assumed maximum annual dose of one millirem, are calculated for several selected times following shutdown of a facility. It is concluded that the methodology presented in this paper results in defensible acceptable residual contamination levels that are directly relatable to risk assessment with the proviso that an acceptable limit to the maximum annual dose will be established. (author)

  10. A new cleaning process for the metallic contaminants on a post-CMP wafer's surface

    International Nuclear Information System (INIS)

    Gao Baohong; Liu Yuling; Wang Chenwei; Wang Shengli; Zhou Qiang; Tan Baimei; Zhu Yadong

    2010-01-01

    This paper presents a new cleaning process using boron-doped diamond (BDD) film anode electrochemical oxidation for metallic contaminants on polished silicon wafer surfaces. The BDD film anode electrochemical oxidation can efficiently prepare pyrophosphate peroxide, pyrophosphate peroxide can oxidize organic contaminants, and pyrophosphate peroxide is deoxidized into pyrophosphate. Pyrophosphate, a good complexing agent, can form a metal complex, which is a structure consisting of a copper ion, bonded to a surrounding array of two pyrophosphate anions. Three polished wafers were immersed in the 0.01 mol/L CuSO 4 solution for 2 h in order to make comparative experiments. The first one was cleaned by pyrophosphate peroxide, the second by RCA (Radio Corporation of America) cleaning, and the third by deionized (DI) water. The XPS measurement result shows that the metallic contaminants on wafers cleaned by the RCA method and by pyrophosphate peroxide is less than the XPS detection limits of 1 ppm. And the wafer's surface cleaned by pyrophosphate peroxide is more efficient in removing organic carbon residues than RCA cleaning. Therefore, BDD film anode electrochemical oxidation can be used for microelectronics cleaning, and it can effectively remove organic contaminants and metallic contaminants in one step. It also achieves energy saving and environmental protection. (semiconductor technology)

  11. GWSCREEN: A semi-analytical model for assessment of the groundwater pathway from surface or buried contamination: Theory and user's manual

    International Nuclear Information System (INIS)

    Rood, A.S.

    1992-03-01

    GWSCREEN was developed for assessment of the groundwater pathway from leaching of radioactive and non radioactive substances from surface or buried sources. The code was designed for implementation in the Track 1 and Track 2 assessment of Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) sites identified as low probability hazard at the Idaho National Engineering Laboratory (DOE, 1991). The code calculates the limiting soil concentration such that regulatory contaminant levels in groundwater are not exceeded. The code uses a mass conservation approach to model three processes: Contaminant release from a source volume, contaminant transport in the unsaturated zone, and contaminant transport in the saturated zone. The source model considers the sorptive properties and solubility of the contaminant. Transport in the unsaturated zone is described by a plug flow model. Transport in the saturated zone is calculated with a semi-analytical solution to the advection dispersion equation for transient mass flux input

  12. Correlation of BTEX levels and toxicity of condensate contaminated groundwater

    International Nuclear Information System (INIS)

    Headley, J.; Goudey, S.; Birkholz, D.; Hardisty, P.

    1995-01-01

    The concentration of BTEX was determined for 60 groundwater samples collected from 6 gas plants in Western Canada, using conventional purge-and-trap GC/MS procedures. The gas plants were selected to cover different types of operations with different amine process chemicals employed for the sweetening of the raw sour-gas condensates. Aliquots of the ground water samples were subjected to toxicity screening tests, specifically, (a) bacterial luminescence (microtox); (b) daphnia mortality and (c) fathead minnow mortality. For the toxicity tests, sample handling procedures were developed to minimize the loss of volatile organics during the experiments. To account for possible losses, the levels of BTEX were monitored at the start and upon completion of these tests. The results indicated that the toxicity of the groundwater was in general, well correlated to the concentration of BTEX (primarily xylene). Approximately 5% of the samples, however, were observed to be toxic although the concentration of BTEX were below the method detection limit (1 microg/1). Thiophenic volatile organics were implicated for the latter. Based on the laboratory results, the remediation of BTEX is expected to correlate with the removal of the toxicity of the groundwater. These findings are of direct relevance to present technologies employed for remediation of ground water at the Sourgas plants

  13. Geohydrology and susceptibility of major aquifers to surface contamination in Alabama; area 11

    Science.gov (United States)

    Castleberry, R.D.; Moreland, R.S.; Scott, J.C.

    1989-01-01

    This report delineates and describes the geohydrology and susceptibility of major aquifers to contamination in Butler, Conecuh, Covington, Crenshaw, Escambia, and Monroe Counties, Alabama. The major aquifers are the Pliocene-Miocene, Upper Floridan, Lisbon, Nanafalia-Clayton, and Providence-Ripley. The largest pumping centers in the area are Andalusia and Monroeville, where groundwater use is about 5 and 4 million gal/day, respectively. Estimated maximum withdrawal in 1987 for all uses in the area was about 44 million gal/day. Depressions have developed in the potentiometric surfaces of the Lisbon aquifer near Andalusia and Opp, the Nanafalia-Clayton aquifer near Luverne, Andalusia, Beatrice, and Monroeville, and the Providence-Ripley aquifer at Greenville. Significant declines in the potentiometric surfaces of the other major aquifers are not apparent. Recharge areas for all major aquifers are susceptible to contamination, but the probability of contamination of the Lisbon, Nanafalia-Clayton, and Providence-Ripley aquifers is low because the recharge areas are remote from areas of the withdrawal. The depressions in the recharge area for the Upper Floridan aquifer and the area where the Pliocene-Miocene aquifer is overlain by the gravelly sands of the Citronelle Formation are highly susceptible to contamination from the surface. (USGS)

  14. Effect of surface contamination on osseointegration of dental implants surrounded by circumferential bone defects.

    Science.gov (United States)

    Mohamed, Seif; Polyzois, Ioannis; Renvert, Stefan; Claffey, Noel

    2010-05-01

    This study was designed to evaluate the effect of surface contamination on osseointegration of dental implants surrounded by a circumferential bone defect and to compare osseointegration around Osseotite with that around Nanotite implants. The premolars on both sides of the mandible in four beagle dogs were extracted. Following 4 months healing, two Nanotite implants and two Osseotite implants were partially inserted in the left side of each mandible. Some threads protruded from the tissues into the oral cavity. Following a 5 week healing period, the implants were removed and the contaminated part of each implant was cleaned. They were then installed to the full implant length on the contra lateral side of the mandibles. The coronal 5 mm of each implant was surrounded by 1 mm circumferential bone defect. Following 12 weeks of healing period, the dogs were sacrificed and biopsies were obtained. Ground sections were prepared for histomorphometric analysis. All implants were associated with direct bone-to-implant contact on the portion of the implant surface contaminated previously and surrounded by bone defect. Nanotite implants performed better than Osseotite implants. The results demonstrated that implant surfaces, which were contaminated previously and were surrounded by bone defects, can osseointegrate.

  15. Heavy metal contamination in surface runoff sediments of the urban area of Vilnius, Lithuania

    Directory of Open Access Journals (Sweden)

    Gytautas Ignatavičius

    2017-02-01

    Full Text Available Surface runoff from urbanized territories carries a wide range of pollutants. Sediments in untreated runoff from direct discharge stormwater systems significantly contribute to urban waterway pollution. In this study, heavy metal (Pb, Zn, Cu, Cr, Ba, As and Fe contamination in surface runoff sediments of the urban area of the city of Vilnius was investigated. The surface runoff sediment samples were collected from seven dischargers with the highest volume rate of water flow and concentrations of suspended solids. The geospatial analysis of the distribution of heavy metals shows that there are several active pollution sources supplying the dischargers with contaminated sediments. Most of these areas are located in the central part of the city and in old town with intense traffic. Principal components analysis and t-test results clearly depicted the significantly different chemical compositions of winter and autumn surface sediment samples. The sampling approach and assessment of results provide a useful tool to examine the contamination that is generated in urban areas, distinguish pollution sources and give a better understanding of the importance of permeable surfaces and green areas.

  16. Contribution to Surface Water Contamination Understanding by Pesticides and Pharmaceuticals, at a Watershed Scale

    Directory of Open Access Journals (Sweden)

    Stéphanie Piel

    2012-12-01

    Full Text Available This study aims at understanding the presence of regulated and emerging micropollutants, particularly pesticides and pharmaceuticals, in surface water, regarding spatial and temporal influences at a watershed scale. The study of relations between micropollutants and other water quality and hydroclimatic parameters was carried out from a statistical analysis on historical and experimental data of different sampling sites from the main watershed of Brittany, western France. The outcomes point out the influence of urban and rural areas of the watershed as well as the impact of seasons on contamination variations. This work contributes to health risk assessment related to surface water contamination by micropollutants. This approach is particularly interesting in the case of agricultural watersheds such as the one studied, where more than 80% of surface water is used to produce drinking water.

  17. Determination of lead and cadmium contamination levels in industrial milk powders produced in Tehran

    Directory of Open Access Journals (Sweden)

    2015-02-01

    Full Text Available Contamination of dairy products with heavy metals, lead (Pb and Cadmium (Cd in particular, induces their toxic effects on humans. Therefore, this study aimed to determine the contamination levels of Pb and Cd levels in milk powders produced in Tehran area. In this study, a total of 25 samples of milk powder was obtained from four different dairy establishments. The samples were digested and extracted prior to analysis. Pb and Cd concentrations was determined using atomic absorption method with graphite furnace. The results were showed a mean value 57.36 ppb (18.99 to112.90 ppb for Pb and 14.11 ppb (5.73 to 39.43 ppb for Cd. According to Codex Alimentarius, approved levels for Pb and Cd in milk are 1000 and 100 ppb, respectively. Based on results, Pb level was less than standard limit in all samples, whereas Cd concentration in 68% of the samples was estimated higher than the standard limit. Since the percentage of Cd-contaminated samples was high, there is a necessity for frequent monitoring of the contamination levels in dairy products as well as to discover the potential contamination sources.

  18. Mapping the environmental risk potential on surface water of pesticide contamination in the Prosecco's vineyard terraced landscape

    Science.gov (United States)

    Pizarro, Patricia; Ferrarese, Francesco; Loddo, Donato; Eugenio Pappalardo, Salvatore; Varotto, Mauro

    2016-04-01

    Intensive cropping systems today represent a paramount issue in terms of environmental impacts, since agricultural pollutants can constitute a potential threat to surface water, non-target organisms and aquatic ecosystems. Levels of pesticide concentrations in surface waters are indeed unquestionably correlated to crop and soil management practices at field-scale. Due to the numerous applications of pesticides required, orchards and vineyards can represent relevant non-point sources for pesticide contamination of water bodies, mainly prompted by soil erosion, surface runoff and spray drift. To reduce risks of pesticide contamination of surface water, the Directive 2009/128/CET imposed the local implementation of agricultural good practices and mitigation actions such as the use of vegetative buffer filter strips and hedgerows along river and pond banks. However, implementation of mitigation actions is often difficult, especially in extremely fragmented agricultural landscapes characterized by a complex territorial matrix set up on urban sprawling, frequent surface water bodies, important geomorphological processes and protected natural areas. Typically, such landscape matrix is well represented by the, Prosecco-DOCG vineyards area (NE of Italy, Province of Treviso) which lays on hogback hills of conglomerate, marls and sandstone that ranges between 50 and 500 m asl. Moreover such vineyards landscape is characterized by traditional and non-traditional agricultural terraces The general aim of this paper is to identify areas of surface water bodies with high potential risk of pesticide contamination from surrounding vineyards in the 735 ha of Lierza river basin (Refrontolo, TV), one of the most representative terraced landscape of the Prosecco-DOCG area. Specific aims are i) mapping terraced Prosecco-DOCG vineyards, ii) classifying potential risk from pesticide of the different areas. Remote sensing technologies such as four bands aerial photos (RGB+NIR) and Light

  19. Removal and treatment of radioactive, organochlorine and heavy metal contaminants from solid surfaces

    International Nuclear Information System (INIS)

    Grieco, S.A.; Neubauer, E.D.; Rhea, J.R.; Escue, L.S.

    1996-01-01

    The U.S. Department of Energy (DOE) is defining decontamination and decommissioning (D ampersand D) obligations at its sites. Current D ampersand D activities are Generally labor intensive, use chemical reagents that are difficult to treat, and may expose workers to radioactive and hazardous chemicals. Therefore, new technologies are desired that minimize waste, allow much of the decommissioned materials to be reused rather than disposed of as waste, and produce wastes that will meet disposal criteria The O'Brien ampersand Gere Companies tested a scouring decontamination system on concrete and steel surfaces contaminated with radioactive and hazardous wastes under the sponsorship of Martin Marietta Energy Systems, Inc. (MMES) at DOE's K-25 former gaseous diffusion plant in Oak Ridge, Tennessee. The scouring system that O'Brien ampersand Gere Companies developed removes fixed radioactive and hazardous surface contamination, while leaving the surface intact. Blasting residuals are dissolved and treated using physical/chemical processes. Bench- and pilot-scale testing of the soda blasting system was conducted between December 1993 and September 1994 on surfaces contaminated with uranium, technetium, heavy metals, and PCBs. Areas of concrete and metal surfaces were blasted. Blasting residuals were dissolved in tap water and treated for radioactive, hazardous, and organochlorine constituents. The treatment system comprised pH adjustment, aeration, solids settling, filtration, carbon adsorption, and ion exchange. This system produced treated water and residual solid waste. Testing demonstrated that the system is capable of removing greater than 95% of radioactive and PCB surface contamination to below DOE's unrestricted use release limits; aqueous radionuclides, heavy metals, and PCBs were below DOE and USEPA treatment objectives after blasting residuals treatment. Waste residuals volume was decreased by 71%

  20. Surface encapsulation process for managing low-level radioactive wastes

    International Nuclear Information System (INIS)

    Unger, S.L.; Telles, R.W.

    1986-01-01

    Current processes for low-level radioactive waste (LLRW) stabilization involve mixing contaminants with a fixative such as cement, asphalt, polyethylene, or vinyl monomers, and subsequently curing the mixtures in containers. These methods give rise to processing difficulties and yield products lacking performance to assure long-term LLRW immobilization. Mixing of LLRW into fixatives is impeded by viscous media and the curing reaction is inhibited by LLRW constituents. Product performance is affected by corrosion of the containers which ultimately expose the cured mixtures to environmental stresses. This process, termed the ''Surface Encapsulation Process,'' circumvents these problems. A thermosetting fixative is employed that mixes readily with LLRW and is highly insensitive to inhibition in curing. The agglomerated mixtures are further stabilized by encapsulation with seamless jackets of corrosion resistant plastic, such as polyethylene. In laboratory-scale investigations, feasibility of the technique was demonstrated for managing a broad spectrum of LLRW simulants including ion-exchange resins, beads, and glasses, and sodium salts. Products tested to date meet all relevant NRC and DOT regulations governing waste fixation. The high waste loadings of the products, use of commodity resins, and processing simplicity indicated our process would provide high performance LLRW stabilization at costs that are competitive to those for processes employing state-of-the-art fixatives. An economic analysis based on managing LLRW generated by commercial power plants (≅1,000 MeW) substantiates the competitive process costs advantages

  1. Quantification of mold contamination in multi-level buildings using the Environmental Relative Moldiness Index

    Science.gov (United States)

    The goal of this study was to evaluate the possible use of the Environmental Relative Moldiness Index (ERMI) to quantify mold contamination in multi-level, office buildings. Settled-dust samples were collected in multi-level, office buildings and the ERMI value for each sample de...

  2. Effects of Land Use Types on the Levels of Microbial Contamination ...

    African Journals Online (AJOL)

    The effects of land use types on levels of microbial contamination based on total coliforms and E. coli (faecal coliform) levels was investigated in the Mara River system, Kenya and Tanzania. Water samples were taken from five sampling sites with different land uses and the Most Probable Number (MPN) method used to ...

  3. Evolution of cadmium tolerance and associated costs in a Gammarus fossarum population inhabiting a low-level contaminated stream.

    Science.gov (United States)

    Vigneron, A; Geffard, O; Coquery, M; François, A; Quéau, H; Chaumot, A

    2015-08-01

    Deciphering evolutionary processes occurring within long-term contaminated wild populations is essential for the ecological risk assessment of persistent chemical contaminations. Using field populations of Gammarus, a commonly-used genus in aquatic ecotoxicology, the present study sought to gain insights into the extent to which long-term exposure to metals in the field could effectively lead to shifts in toxicological sensitivities. For this, we identified a Gammarus population inhabiting a stream contaminated by cadmium (Cd). We compared the Cd-exposure and Cd-sensitivity of this population to those of five reference populations. Active biomonitoring determined in different years and seasons that significant levels of Cd were bioavailable in the contaminated site. Laboratory sensitivity tests under common garden conditions established that this long-term field exposure led to the development of a moderate Cd tolerance, which was maintained after a 3-week acclimatization in the laboratory, and transmitted to offspring produced under clean conditions. The potential physiological costs of tolerance were assessed by means of feeding rate measurements (in the laboratory and in situ). They revealed that, unlike for reference populations, the feeding activity of organisms from the tolerant population was greatly decreased when they were maintained under laboratory conditions, potentially indicating a high population vulnerability to environmental perturbations. Because dissolved Cd concentrations in water from the contaminated site were low (averaging 0.045 µg L(-1)) and below the current European environmental quality standard for Cd for inland surface waters (fixed at 0.08 µg L(-1) in soft water environments), this case study sheds light onto the extent to which current environmental quality standards are protective against potential adverse outcomes of adaptive and micro-evolutionary processes occurring in contaminated environments.

  4. Fermi level on hydrogen terminated diamond surfaces

    Czech Academy of Sciences Publication Activity Database

    Rezek, Bohuslav; Saurer, C.; Nebel, C. E.; Stutzmann, M.; Ristein, J.; Ley, L.; Snidero, E.; Bergonzo, P.

    2003-01-01

    Roč. 82, č. 14 (2003), s. 2266-2268 ISSN 0003-6951 EU Projects: European Commission(XE) HPRN-CT-1999-00139 Grant - others:DFC(DE) NE524-2 Institutional research plan: CEZ:AV0Z1010914 Keywords : atomic force microscope(AFM) * Kelvin probe experiments * diamond surface Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 4.049, year: 2003

  5. Uncertainty of mass discharge estimation from contaminated sites at screening level

    DEFF Research Database (Denmark)

    Thomsen, Nanna Isbak; Troldborg, M.; McKnight, Ursula S.

    that only the sites that present an actual risk are further investigated and perhaps later remediated. We propose a method for quantifying the uncertainty of dynamic mass discharge estimates from poorly characterised contaminant point sources on the local scale. Techniques for estimating dynamic uncertainty......Contaminated sites threaten groundwater resources worldwide. The number of contaminated sites is large and there are too few economic resources available to ensure a thorough investigation and remediation of them all. Risk assessment must already be done at a screening level in order to ensure...... are not currently available for such sites. Mass discharge estimates (mass/time) have been proposed as a useful metric in risk assessment, because they provide an estimate of the impact of a contaminated site on a given water resource and allow for the comparison of impact between different sites. But mass...

  6. The level of Escherichia coli contamination in foods and drinks sold at canteens campus

    Directory of Open Access Journals (Sweden)

    Dewi Susanna

    2011-02-01

    Full Text Available Background: Bacterial contamination is a common phenomenon in foods served in campus canteens and my cause physical illness which will affect academic activity. The aim of this study was to rank the level of Escherichia coli contamination in food and drink in campus canteens.Methods: Forty nine (49 foods and 24 types of drink were examined using conventional agar broth method for calculation of most probable number (MPN. The steps of the mothod were presumptive test for coliforms, fecal coliforms and E. coli, confirmes test for coliforms, fecal coli and E. coli and then completed test for E. coli. An analysis for contamination by E. coli in meals, utensils, and on the hands of the server was also undertaken. The data analyzed in percentage and rank all type of foods and drinks, also rank based on the location.Results: Almost all type of meals was contaminated. Meals with chili sauce were the most risky from the contamination of E. coli (90.15 %, then followed by dry meals (38.89%, while the wet meals were the the most unrisky meals. In  drinks, the highest was lacy juice, followed by jambu (guava juice, then Sirsak and Orange juices on the third rank, while the mango juice was the lowest contamination. Melon juice, cappucino and fruit-coctail did not have E. coli  contamination.Conclusion: The contamination in the top three rank of contamination could be from the utensils used and foodhandler. (Med J Indones 2011; 20:66-70Keywords: campus, canteen, drink, Escherichia coli, food

  7. Method for restoring contaminants to base levels in previously leached formations

    International Nuclear Information System (INIS)

    Strom, E.T.; Espencheid, W.F.

    1983-01-01

    The present invention relates to a method for restoring to environmentally acceptable levels the soluble contaminants in a subterranean formation that has been subjected to oxidative leaching. The contaminants are defined as those ionic species that when subjected to calcium ions form precipitates which are insoluble in the formation fluids. In accordance with the present invention, soluble calcium values are introduced into the formation. The level of contaminants is monitored and when such reaches the desired level, the introduction of soluble calcium values is stopped. The introduction of calcium values may be achieved in several ways one of which is to inject into the formation an aqueous solution containing therein solubilized calcium values. Another method of introducing calcium values into a formation, is to inject into the formation an aqueous solution containing carbon dioxide to solubilize calcium values, such as calcium carbonates, found in the formation

  8. Cuban-Brazilian comparison of the calibration procedures for surface contamination monitors

    International Nuclear Information System (INIS)

    Salas, Gonzalo W.; Garcia, Jose A.T.; Ramos, Manoel M.O.

    2007-01-01

    The calibration laboratory of the CPHR, Centro de Proteccion e Higiene de las Radiaciones, is the only laboratory that performs calibrations of radiation protection instruments in Cuba. Recently they started a cooperation project with IAEA, code number CUB3002-01 with the task title 'Assuring and Demonstrating the safety of radioactive Waste Management'. Within the frame of this project they have a compromise to implement the calibration service for surface contamination monitors, for which they received instruments and sources. In 2006 the Laboratorio Nacional de Metrologia das Radiacoes Ionizantes (LNMRI) from the Instituto de Radioprotecao e Dosimetria, IRD/CNEN, was invited to perform a mission to CPHR in order to evaluate the level of implementation of the service trough the insertion of the service in the Quality Assurance System of their laboratory, and perform a comparison exercise to test the calibration method implemented. The results were evaluated by the methodology recommended in the ISO/IEC 43-1 standard. These results show that all values from both laboratories are comparable for most radionuclides except for Cl-36. The preliminary investigation about this situation is presented in the paper. (author)

  9. Microbiological quality control of single-walled carbon-nanotubes-coated surfaces experimentally contaminated

    International Nuclear Information System (INIS)

    Natalizi, T.; Frioni, A.; Passeri, D.; Pantanella, F.

    2013-01-01

    The emergence of new nanotechnologies involves the spreading of nanoparticles in various fields of human life. Nanoparticles in general and, more specifically, carbon nanotubes have been adopted for many practical approaches i.e.: coatings for medical devices, food process industry and drug delivery. Humans will be increasingly exposed to nanoparticles but the susceptibility of nanostructured materials to microbial colonization in process of manufacturing and storage has not been thoroughly considered. Therefore, the microbiological quality control of nanoparticles plays a pivotal role. Different analytical methods have been attempted for detecting bacterial population contaminating a surface, but no one can be considered fully appropriate. Here, BioTimer Assay (BTA) and conventional sonication followed by colony forming units method (S-CFU) were applied for microbiological quality control of single-walled carbon nanotubes (SWCNTs)-coated surfaces experimentally contaminated with Streptococcus mutans and Pseudomonas aeruginosa. Our results demonstrated that S-CFU is unreliable to actually determine the number of bacteria, contaminating abiotic surfaces, as it does not detach all adherent bacteria and kills part of the bacterial population. Instead, BTA is a reliable method to enumerate bacteria colonizing SWCNTs-coated surfaces and can be considered a useful tool for microbiological quality control of nanomaterials for human use.

  10. Contamination by persistent toxic substances in surface sediment of urban rivers in Chaohu City, China.

    Science.gov (United States)

    Li, Feipeng; Zhang, Haiping; Meng, Xiangzhou; Chen, Ling; Yin, Daqiang

    2012-01-01

    The concentration and spatial distribution of persistent toxic substances (PTS) in the river sediment in Chaohu City, China were investigated. A total of nine surface sediments were collected and the selected PTS pollutants including six heavy metals and nineteen polybrominated diphenyl ethers (PBDEs) were analyzed. The mean heavy metal concentrations (in mg/kg, dry weight) ranged within 0.18-1.53 (Hg), 50.08-200.18 (Cu), 118.70-313.65 (Zn), 50.77-310.85 (Cr), 37.12-92.72 (Pb) and 13.29-197.24 (As), and Cu, Zn and As have been regarded as the main metal pollutants. The levels of PBDEs (1.2-12.1 ng/g) and BDE-209 (2.4-30.5 ng/g) were at the middle level of the global range. BDE-209 was the predominant congener (67.0%-85.7%), which agrees with the fact that technical deca-BDE mixtures are the dominant PBDE formulation in China. The relative high level of PTS pollutants in the western part of the city is probably owing to the intensive agricultural activities and lack of sewerage system there. The ecological risk assessment with the sediment quality guidelines (SOGs) indicates that the urban river sediments in the city have been heavily contaminated by heavy metals with probable ecotoxicological impacts on freshwater organisms and the main toxic pollutants are Hg and As. The results of current study imply that the city, and perhaps many other small cities in China as well, requires immediate pollution control measures with emphasis on not only conventional organic pollutants but also on PTS such as heavy metals and PBDEs.

  11. Transport of contaminants by Arctic sea ice and surface ocean currents

    International Nuclear Information System (INIS)

    Pfirman, S.

    1995-01-01

    Sea ice and ocean currents transport contaminants in the Arctic from source areas on the shelves, to biologically active regions often more than a thousand kilometers away. Coastal regions along the Siberian margin are polluted by discharges of agricultural, industrial and military wastes in river runoff, from atmospheric deposition and ocean dumping. The Kara Sea is of particular concern because of deliberate dumping of radioactive waste, as well as the large input of polluted river water. Contaminants are incorporated in ice during suspension freezing on the shelves, and by atmospheric deposition during drift. Ice releases its contaminant load through brine drainage, surface runoff of snow and meltwater, and when the floe disintegrates. The marginal ice zone, a region of intense biological activity, may also be the site of major contaminant release. Potentially contaminated ice from the Kara Sea is likely to influence the marginal ice zones of the Barents and Greenland seas. From studies conducted to date it appears that sea ice from the Kara Sea does not typically enter the Beaufort Gyre, and thus is unlikely to affect the northern Canadian and Alaskan margins

  12. Occurrence of perchloroethylene in surface water and fish in a river ecosystem affected by groundwater contamination.

    Science.gov (United States)

    Wittlingerová, Zdena; Macháčková, Jiřina; Petruželková, Anna; Zimová, Magdalena

    2016-03-01

    Long-term monitoring of the content of perchloroethylene (PCE) in a river ecosystem affected by groundwater contamination was performed at a site in the Czech Republic. The quality of surface water was monitored quarterly between 1994 and 2013, and fish were collected from the affected ecosystem to analyse the content of PCE in their tissue in 1998, 2011 and 2012. Concentrations of PCE (9-140 μg/kg) in the tissue of fish collected from the contaminated part of the river were elevated compared to the part of the river unaffected by the contamination (ND to 5 μg/kg PCE). The quality of surface water has improved as a result of groundwater remediation during the evaluated period. Before the remedial action, PCE concentrations ranged from 30 to 95 μg/L (1994-1997). Following commencement of remedial activities in September 1997, a decrease in the content of PCE in the surface water to 7.3 μg/L (1998) and further to 1 μg/L (2011) and 1.1 μg/L (2012) led to a progressive decrease in the average concentration of PCE in the fish muscle tissue from 79 μg/kg (1998) to 24 (2011) and 30 μg/kg (2012), respectively. It was determined that the bioconcentration of PCE does not have a linear dependence because the decrease in contamination in the fish muscle tissue is not directly proportional to the decrease in contamination in the river water. The observed average bioconcentration factors were 24 and 28 for the lower concentrations of PCE and 11 for the higher concentrations of PCE in the river. In terms of age, length and weight of the collected fish, weight had the greatest significance for bioconcentration, followed by the length, with age being evaluated as a less significant factor.

  13. The development of the American National Standard 'control of radioactive surface contamination on materials equipment and facilities to be released for uncontrolled use'

    International Nuclear Information System (INIS)

    Shapiro, J.

    1980-01-01

    A new standard submitted by the Health Physics Society Standards Committee to the American National Standards Institute concerning radioactive surface contamination of materials and equipment is discussed. The chronological events in the development of this standard are given. The standard provides criteria for the release for uncontrolled use of materials, equipment and facilities contaminated or potentially contaminated with radioactivity. Permissible contamination limits are specified for: 1) long lived alpha emitters except natural uranium and thorium, 2) more hazardous beta-gamma emitters, 3) less hazardous beta-gamma emitters and 4) natural uranium and thorium. A contamination reference level of 1000 dpm/100 cm 2 for 90 Sr was set as the basis for assigning limits to radionuclides presenting an ingestion hazard and other radionuclides were grouped based on the values of their maximum permissible concentration (MPC) in water relative to 90 Sr. The contamination limit for 239 Pu was chosen as the basis for assigning limits based on MPC in air to radionuclides presenting an inhalation hazard; a value of 100 dpm/100 cm 2 was adopted in the standard. An upper limit of 5000 dpm/100 cm 2 for surface contamination was selected for the standard. (UK)

  14. Sea Level Rise Induced Arsenic Release from Historically Contaminated Coastal Soils.

    Science.gov (United States)

    LeMonte, Joshua J; Stuckey, Jason W; Sanchez, Joshua Z; Tappero, Ryan; Rinklebe, Jörg; Sparks, Donald L

    2017-06-06

    Climate change-induced perturbations in the hydrologic regime are expected to impact biogeochemical processes, including contaminant mobility and cycling. Elevated levels of geogenic and anthropogenic arsenic are found along many coasts around the world, most notably in south and southeast Asia but also in the United States, particularly along the Mid-Atlantic coast. The mechanism by and the extent to which arsenic may be released in contaminated coastal soils due to sea level rise are unknown. Here we show a series of data from a coastal arsenic-contaminated soil exposed to sea and river waters in biogeochemical microcosm reactors across field-validated redox conditions. We find that reducing conditions lead to arsenic release from historically contaminated coastal soils through reductive dissolution of arsenic-bearing mineral oxides in both sea and river water inundations, with less arsenic release from seawater scenarios than river water due to inhibition of oxide dissolution. For the first time, we systematically display gradation of solid phase soil-arsenic speciation across defined redox windows from reducing to oxidizing conditions in natural waters by combining biogeochemical microcosm experiments and X-ray absorption spectroscopy. Our results demonstrate the threat of sea level rise stands to impact arsenic release from contaminated coastal soils by changing redox conditions.

  15. Investigating uranium distribution in surface sediments and waters: a case study of contamination from the Juniper Uranium Mine, Stanislaus National Forest, CA.

    Science.gov (United States)

    Kayzar, Theresa M; Villa, Adam C; Lobaugh, Megan L; Gaffney, Amy M; Williams, Ross W

    2014-10-01

    The uranium concentrations and isotopic compositions of waters, sediment leachates and sediments from Red Rock Creek in the Stanislaus National Forest of California were measured to investigate the transport of uranium from a point source (the Juniper Uranium Mine) to a natural surface stream environment. The ((234)U)/((238)U) composition of Red Rock Creek is altered downstream of the Juniper Mine. As a result of mine-derived contamination, water ((234)U)/((238)U) ratios are 67% lower than in water upstream of the mine (1.114-1.127 ± 0.009 in the contaminated waters versus 1.676 in the clean branch of the stream), and sediment samples have activity ratios in equilibrium in the clean creek and out of equilibrium in the contaminated creek (1.041-1.102 ± 0.007). Uranium concentrations in water, sediment and sediment leachates are highest downstream of the mine, but decrease rapidly after mixing with the clean branch of the stream. Uranium content and compositions of the contaminated creek headwaters relative to the mine tailings of the Juniper Mine suggest that uranium has been weathered from the mine and deposited in the creek. The distribution of uranium between sediment surfaces (leachable fraction) and bulk sediment suggests that adsorption is a key element of transfer along the creek. In clean creek samples, uranium is concentrated in the sediment residues, whereas in the contaminated creek, uranium is concentrated on the sediment surfaces (∼70-80% of uranium in leachable fraction). Contamination only exceeds the EPA maximum contaminant level (MCL) for drinking water in the sample with the closest proximity to the mine. Isotopic characterization of the uranium in this system coupled with concentration measurements suggest that the current state of contamination in Red Rock Creek is best described by mixing between the clean creek and contaminated upper branch of Red Rock Creek rather than mixing directly with mine sediment. Published by Elsevier Ltd.

  16. Field emission and high voltage cleaning of particulate contaminants on extended metallic surfaces

    International Nuclear Information System (INIS)

    Tan, J.; Bonin, B.; Safa, H.

    1996-01-01

    The vacuum insulation properties of extended metallic surfaces depends strongly on their cleanliness. The usual technique to reduce electronic field emission from such surfaces consists in exposing them to very high electric fields during limited periods of time. This kind of processing also reduces the occurrence of vacuum breakdown. The processing of the surface is generally believed to be due to a thermomechanical destruction of the emitting sites, initiated by the emission itself. Comparison of the electric forces vs adherence forces which act on dust particles lying on the surface shows that the processing could also be due simply to the mechanical removal of the dust particles, with a subsequent reduction of field emission from the contaminated surface. (author)

  17. A state of the art on the measurement of the radioactive contamination in the inner surface of the pipe

    Energy Technology Data Exchange (ETDEWEB)

    Seo, B. K.; Lee, K. W.; Oh, W. Z.; Woo, Z. H.; Kim, G. H

    2004-11-15

    Many radioactive wastes are produced during the decommissioning of the nuclear facilities. Their radiological characterization must be estimated for disposal and reuse. Especially, it is very difficult to measure the in-pipe surface contamination, because of the difficulty of access. So, it is necessary to develop the measurement technology for the in-pipe surface contamination. In the developed counties of the decommissioning technology such as America, Japan etc. they developed the measuring device for the in-pipe radioactive contamination and performed the capacity estimation. In this report, the state of the art on the measurement of the radioactive contamination in the inner surface of the pipe and radiation detector for measuring the each radiation(alpha, beta, and gamma) proceeding around the world was analyzed. By means of such technology analysis, we will develop the measuring technology of the radioactive contamination in the inner surface of the pipe and apply to the decommissioning sites.

  18. Levels and risk assessment of chemical contaminants in byproducts for animal feed in Denmark

    DEFF Research Database (Denmark)

    Mortensen, Alicja; Granby, Kit; Eriksen, Folmer Damsted

    2014-01-01

    With aim to provide information on chemical contaminants in byproducts in animal feed, the data from an official control by the Danish Plant Directorate during 1998-2009, were reviewed and several samples of citrus pulp and dried distillers grains with solubles (DDGS) were additionally collected...... for analysis and risk assessment. The levels of contaminants in the samples from the official control were below maximum limits from EU regulations with only a few exceptions in the following groups; dioxins and dioxin-like polychlorobiphenyls (PCBs) in fish-containing byproducts and dioxins in vegetable...... and animal fat, hydrogen cyanide in linseed, and cadmium in sunflowers. The levels of pesticides and mycotoxins in the additionally collected samples were below maximum limits. Enniatin B (ENN B) was present in all DDGS samples. The hypothetical cases of carry-over of contamination from these byproducts were...

  19. New miniaturized alpha/beta spectrometric system for the surface contamination monitoring and radon personal dosimeter

    International Nuclear Information System (INIS)

    Streil, T.; Oeser, V.; Holfeld, G.

    1998-01-01

    The heart of the new miniaturized alpha/beta spectroscopic system is a Smart Card MCA having a 12 bit resolution and a 32 bit memory for each channel with the size of a cheque card. The system consists of a single or up to 12 alpha spectrometers in a battery powered casing with connectors for direct detector/amplifier module plugging. Surface contamination in the order of 1 Bq/cm 2 of 239 Pu can be measured. (M.D.)

  20. Evaluation of surface contamination based on certifiably traceable, internationally accreditable measurements

    International Nuclear Information System (INIS)

    Whitlock, G.D.

    1992-01-01

    National Accreditation and Measurement Service (NAMAS) adopted by the EUROMET agreement requires that the calibration of monitoring instruments be traceable internationally with the objective that radiation hazard assessment be improved. This objective is achieved for Tritium surface contamination by employing calibration sources and evaluation methods which comply with ISO standards including the measurement of activity removable by Volatilization as well as dust. Consideration should be given to organic binding of tritium in the skin with its implications in the event of litigation. (author)

  1. Detecting buried radium contamination using soil-gas and surface-flux radon meaurements

    International Nuclear Information System (INIS)

    Karp, K.E.

    1988-06-01

    The Technical Measurements Center (TMC) has investigated the effectiveness of using radon soil-gas under surface-flux measurments to locate radium contamination that is buried sufficiently deep to be undetectable by surface gamma methods. At the first test site studied, an indication of a buried source was revealed by mapping anomalous surface-flux and soil-gas concentrations in the near surface overburden. The mapped radon anomalies were found to correspond in rough outline to the shape of the areal extent of the deposit as determined by borehole gamma-ray logs. The 5.9pCi/g radium deposit, buried 2 feet below the surface, went undetected by conventional surface gamma measurements. Similar results were obtained at the second test site where radon and conventional surface gamma measurements were taken in an area having radium concentrations ranging from 13.3 to 341.0 pCi/g at a depth of 4 feet below the surface. The radon methods were found to have a detection limit for buried radium lower than that of the surface gamma methods, as evidenced by the discovery of the 13.3 pCi/g deposit which went undetected by the surface gamma methods. 15 refs., 33 figs., 8 tabs

  2. Physical-level synthesis for digital lab-on-a-chip considering variation, contamination, and defect.

    Science.gov (United States)

    Liao, Chen; Hu, Shiyan

    2014-03-01

    Microfluidic lab-on-a-chips have been widely utilized in biochemical analysis and human health studies due to high detection accuracy, high timing efficiency, and low cost. The increasing design complexity of lab-on-a-chips necessitates the computer-aided design (CAD) methodology in contrast to the classical manual design methodology. A key part in lab-on-a-chip CAD is physical-level synthesis. It includes the lab-on-a-chip placement and routing, where placement is to determine the physical location and the starting time of each operation and routing is to transport each droplet from the source to the destination. In the lab-on-a-chip design, variation, contamination, and defect need to be considered. This work designs a physical-level synthesis flow which simultaneously considers variation, contamination, and defect of the lab-on-a-chip design. It proposes a maze routing based, variation, contamination, and defect aware droplet routing technique, which is seamlessly integrated into an existing placement technique. The proposed technique improves the placement solution for routing and achieves the placement and routing co-optimization to handle variation, contamination, and defect. The simulation results demonstrate that our technique does not use any defective/contaminated grids, while the technique without considering contamination and defect uses 17.0% of the defective/contaminated grids on average. In addition, our routing variation aware technique significantly improves the average routing yield by 51.2% with only 3.5% increase in completion time compared to a routing variation unaware technique.

  3. Decontamination effects of detergents on the market for radioactive surface contamination. Their comparative test (2)

    Energy Technology Data Exchange (ETDEWEB)

    Miyabe, Kenjiro; Takasaki, Koji; Horiuchi, N. [Japan Nuclear Cycle Development Inst., Tokai, Ibaraki (Japan). Tokai Works; Yasunaka, Hideo; Izumi, Yuichi [Japan Environment Research Co. Ltd., Tokyo (Japan)

    1999-04-01

    There happens frequently radioactive surface contamination on human body and skin under radiation works in controlled area. The surface contamination should be removed from the body and the skin as soon as possible for radiation control and exposure management. Titanium oxide paste, which is reserved as detergent for radioactive surface contamination, has satisfactory results and reliability for decontamination effects. The titanium oxide paste, however, has a short preservation period, and must be exchanged and supplied every several months. Decontamination tests for 22 kinds of detergents on the market were carried out with swine skin and radiation materials, Cs-137 and Ru-106. Radiation solution of Cs-137 or Ru-106 was dropped on the swine skin sample, which was left for 5 min or 40 min as it is. Radioactivity of the sample was measured before and after washing of the detergents. Decontamination effects of the detergents for Cs-137 were similar to those for Ge-144 which were tested in the previous year. The decontamination effects for Ru-106, however, were remarkably lower than those for both cases of Cs-137 and Ge-144. (M. Suetake)

  4. Mathematical simulation of sediment and contaminant transport in surface waters. Annual report, October 1977--September 1978

    International Nuclear Information System (INIS)

    Onishi, Y.; Arnold, E.M.; Serne, R.J.; Cowan, C.E.; Thompson, F.L.; Mayer, D.W.

    1979-01-01

    Various pathways exist for exposure of humans and biota to radioactive materials released from nuclear facilities. Hydrologic transport (liquid pathway) is one element in the evaluation of the total radiation dose to man. Mathematical models supported by well-planned field data collection programs can be useful tools in assessing the hydrologic transport and ultimate fate of radionuclides. Radionuclides with high distribution coefficients or radionuclides in surface waters with high suspended sediment concentrations are, to a great extent, adsorbed by river and marine sediments. Thus, otherwise dilute contaminants are concentrated. Contaminated sediments may be deposited on the river and ocean beds creating a significant pathway to man. Contaminated bed sediment in turn may become a long-term source of pollution through desorption and resuspension. In order to assess migration and accumulation of radionuclides in surface waters, mathematical models must correctly simulate essential mechanisms of radionuclide transport. The objectives of this study were: (1) to conduct a critical review of (a) radionuclide transport models as well as sediment transport and representative water quality models in rivers, estuaries, oceans, lakes, and reservoirs, and (b) adsorption and desorption mechanisms of radionuclides with sediments in surface waters; (2) to synthesize a mathematical model capable of predicting short- and long-term transport and accumulation of radionuclides in marine environments

  5. Mitigation of cesium and cobalt contamination on the surfaces of RAM packages

    International Nuclear Information System (INIS)

    Krumhansl, J.; Bonhomme, F.; McConnell, P.; Kapoor, A.

    2004-01-01

    Techniques for mitigating the adsorption of 137 Cs and 60 Co on metal surfaces (e.g., RAM packages) exposed to contaminated water (e.g., spent-fuel pools) has been developed and experimentally verified. The techniques are also effective in removing some of the 60 Co and 137 Cs that may have been adsorbed on the surfaces after removal from the contaminated water. The principle for the 137 Cs mitigation technique is based upon ion-exchange processes. In contrast, 60 Co contamination primarily resides in minute particles of CRUD that become lodged on cask surfaces. CRUD is an insoluble Fe-Ni-Cr oxide that forms colloidal-sized particles as stainless steels corrode. Because of the similarity between Ni +2 and Co +2 , CRUD is able to scavenge and retain traces of cobalt as it forms. A number of organic compounds have a great specificity for combining with nickel and cobalt. Ongoing research is investigating the effectiveness of chemical complexing agent, EDTA, with regard to its ability to dissolve the host phase (CRUD) thereby liberating the entrained 60Co into a solution where it can be rinsed away

  6. Detection of fecal contamination on beef meat surfaces using handheld fluorescence imaging device (HFID)

    Science.gov (United States)

    Oh, Mirae; Lee, Hoonsoo; Cho, Hyunjeong; Moon, Sang-Ho; Kim, Eun-Kyung; Kim, Moon S.

    2016-05-01

    Current meat inspection in slaughter plants, for food safety and quality attributes including potential fecal contamination, is conducted through by visual examination human inspectors. A handheld fluorescence-based imaging device (HFID) was developed to be an assistive tool for human inspectors by highlighting contaminated food and food contact surfaces on a display monitor. It can be used under ambient lighting conditions in food processing plants. Critical components of the imaging device includes four 405-nm 10-W LEDs for fluorescence excitation, a charge-coupled device (CCD) camera, optical filter (670 nm used for this study), and Wi-Fi transmitter for broadcasting real-time video/images to monitoring devices such as smartphone and tablet. This study aimed to investigate the effectiveness of HFID in enhancing visual detection of fecal contamination on red meat, fat, and bone surfaces of beef under varying ambient luminous intensities (0, 10, 30, 50 and 70 foot-candles). Overall, diluted feces on fat, red meat and bone areas of beef surfaces were detectable in the 670-nm single-band fluorescence images when using the HFID under 0 to 50 foot-candle ambient lighting.

  7. Mitigation of cesium and cobalt contamination on the surfaces of RAM packages

    Energy Technology Data Exchange (ETDEWEB)

    Krumhansl, J.; Bonhomme, F.; McConnell, P. [Sandia National Labs., Albuquerque (United States); Kapoor, A. [U.S. Dept. of Energy, Albuquerque (United States)

    2004-07-01

    Techniques for mitigating the adsorption of {sup 137}Cs and {sup 60}Co on metal surfaces (e.g., RAM packages) exposed to contaminated water (e.g., spent-fuel pools) has been developed and experimentally verified. The techniques are also effective in removing some of the {sup 60}Co and {sup 137}Cs that may have been adsorbed on the surfaces after removal from the contaminated water. The principle for the {sup 137}Cs mitigation technique is based upon ion-exchange processes. In contrast, {sup 60}Co contamination primarily resides in minute particles of CRUD that become lodged on cask surfaces. CRUD is an insoluble Fe-Ni-Cr oxide that forms colloidal-sized particles as stainless steels corrode. Because of the similarity between Ni{sup +2} and Co{sup +2}, CRUD is able to scavenge and retain traces of cobalt as it forms. A number of organic compounds have a great specificity for combining with nickel and cobalt. Ongoing research is investigating the effectiveness of chemical complexing agent, EDTA, with regard to its ability to dissolve the host phase (CRUD) thereby liberating the entrained 60Co into a solution where it can be rinsed away.

  8. Viral contamination of aerosol and surfaces through toilet use in health care and other settings.

    Science.gov (United States)

    Verani, Marco; Bigazzi, Roberto; Carducci, Annalaura

    2014-07-01

    The airborne spreading of enteric viruses can occur through the aerosol and droplets produced by toilet flushing. These can contaminate the surrounding environment, but few data exist to estimate the risk of exposure and infection. For this reason environmental monitoring of air and selected surfaces was carried out in 2 toilets of an office building and in 3 toilets of a hospital before and after cleaning operations. To reveal the presence of norovirus, enterovirus, rhinovirus, human rotavirus, and Torque teno virus and to quantify human adenovirus and bacteria counts, molecular and cultural methods were used. On the whole, viruses were detected on 78% of surfaces and in 81% of aerosol. Among the researched viruses, only human adenovirus and Torque teno virus were found in both surface and air samples. In several cases the same adenovirus strain was concurrently found in all matrices. Bacterial counts were unrelated to viral presence and cleaning did not seem to substantially reduce contamination. The data collected in our study confirm that toilets are an important source of viral contamination, mainly in health care settings, where disinfection can have a crucial role in preventing virus spread. Copyright © 2014 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Mosby, Inc. All rights reserved.

  9. Contaminant levels and toxicity of sediments and water of Baltimore Harbor and Back River, Maryland

    International Nuclear Information System (INIS)

    Logan, D.T.; Jacobs, F.; Mehrotra, N.

    1995-01-01

    The Patapsco and Back River Watershed drains the Baltimore metropolitan area, Maryland's most heavily industrialized and urbanized region. Due to the intensive development and industrialization of the Baltimore metropolitan area over the past 250 years, high levels of contaminants have been discharged into Baltimore Harbor on the Patapsco River and into the Back River. Pollutants historically discharged include heavy metals, petroleum hydrocarbons, pesticides, cyanide, sewage, other organic chemicals, and nutrients. Sources have included industrial and municipal discharges, sewerage overflows, urban runoff, and leaks and spills from vessels and on-land facilities. The Maryland Department of the Environment undertook this study of ambient conditions as part of a developing strategy to assess and improve conditions in the Chesapeake Bay and its tributaries. Past studies were compiled, evaluated, and synthesized to identify the areas of degraded conditions and contaminants of possible concern. Sediment contaminant levels were assessed using historical sediment chemistry data, Effects Range Low and Median concentrations (ER-L and ER-M) as toxicological benchmarks, and a sum of toxicity units approach for multiple contaminants. Data on toxicity testing and biological monitoring was compared to sediment and water quality data. Fish tissue data were used to examine bioaccumulated chemicals. A computerized Geographical Information System (GIS) was used to manipulate and display complex geographical data. The final identification of areas and chemicals of potential concern relied on a syntheses of these results as well as information on present and past contaminant loadings

  10. Surface and subsurface characterization of uranium contamination at the Fernald environmental management site

    International Nuclear Information System (INIS)

    Schilk, A.J.; Perkins, R.W.; Abel, K.H.; Brodzinski, R.L.

    1993-04-01

    The past operations of uranium production and support facilities at several Department of Energy (DOE) sites have occasionally resulted in the local contamination of some surface and subsurface soils, and the three-dimensional distribution of the uranium at these sites must be thoroughly characterized before any effective remedial protocols can be established. To this end, Pacific Northwest Laboratory (PNL) has been tasked by the DOE's Office of Technology Development with adapting, developing, and demonstrating technologies for the measurement of uranium in surface and subsurface soils at the Fernald Uranium in Soils Integrated Demonstration site. These studies are detailed in this report

  11. Study of luminous phenomena observed on contaminated metallic surfaces submitted to high RF fields

    International Nuclear Information System (INIS)

    Maissa, S.; Junquera, T.; Fouaidy, M.; Le Goff, A.; Bonin, B.; Luong, M.; Safa, H.; Tan, J.

    1995-01-01

    The RF field emission from a sample subjected to high RF fields in a copper cavity has been investigated. The study is focused on the luminous emissions occurring on the RF surface simultaneously with the electron emission. The optical apparatus attached to the cavity permits to observe the evolution of the emitters and the direct effects of the surface conditioning. Also, the parameters of the emitted radiation (intensity, glowing duration, spectral distribution) may provide additional informations on the field emission phenomena. Some results concerning samples intentionally contaminated with particles (metallic or dielectric) are presented. (K.A.)

  12. Methane Bubbles Transport Particles From Contaminated Sediment to a Lake Surface

    Science.gov (United States)

    Delwiche, K.; Hemond, H.

    2017-12-01

    Methane bubbling from aquatic sediments has long been known to transport carbon to the atmosphere, but new evidence presented here suggests that methane bubbles also transport particulate matter to a lake surface. This transport pathway is of particular importance in lakes with contaminated sediments, as bubble transport could increase human exposure to toxic metals. The Upper Mystic Lake in Arlington, MA has a documented history of methane bubbling and sediment contamination by arsenic and other heavy metals, and we have conducted laboratory and field studies demonstrating that methane bubbles are capable of transporting sediment particles over depths as great as 15 m in Upper Mystic Lake. Methane bubble traps were used in-situ to capture particles adhered to bubble interfaces, and to relate particle mass transport to bubble flux. Laboratory studies were conducted in a custom-made 15 m tall water column to quantify the relationship between water column height and the mass of particulate transport. We then couple this particle transport data with historical estimates of ebullition from Upper Mystic Lake to quantify the significance of bubble-mediated particle transport to heavy metal cycling within the lake. Results suggest that methane bubbles can represent a significant pathway for contaminated sediment to reach surface waters even in relatively deep water bodies. Given the frequent co-occurrence of contaminated sediments and high bubble flux rates, and the potential for human exposure to heavy metals, it will be critical to study the significance of this transport pathway for a range of sediment and contaminant types.

  13. Wipe sampling for nicotine as a marker of thirdhand tobacco smoke contamination on surfaces in homes, cars, and hotels.

    Science.gov (United States)

    Quintana, Penelope J E; Matt, Georg E; Chatfield, Dale; Zakarian, Joy M; Fortmann, Addie L; Hoh, Eunha

    2013-09-01

    Secondhand smoke contains a mixture of pollutants that can persist in air, dust, and on surfaces for months or longer. This persistent residue is known as thirdhand smoke (THS). Here, we detail a simple method of wipe sampling for nicotine as a marker of accumulated THS on surfaces. We analyzed findings from 5 real-world studies to investigate the performance of wipe sampling for nicotine on surfaces in homes, cars, and hotels in relation to smoking behavior and smoking restrictions. The intraclass correlation coefficient for side-by-side samples was 0.91 (95% CI: 0.87-0.94). Wipe sampling for nicotine reliably distinguished between private homes, private cars, rental cars, and hotels with and without smoking bans and was significantly positively correlated with other measures of tobacco smoke contamination such as air and dust nicotine. The sensitivity and specificity of possible threshold values (0.1, 1, and 10 μg/m(2)) were evaluated for distinguishing between nonsmoking and smoking environments. Sensitivity was highest at a threshold of 0.1 μg/m(2), with 74%-100% of smoker environments showing nicotine levels above threshold. Specificity was highest at a threshold of 10 μg/m(2), with 81%-100% of nonsmoker environments showing nicotine levels below threshold. The optimal threshold will depend on the desired balance of sensitivity and specificity and on the types of smoking and nonsmoking environments. Surface wipe sampling for nicotine is a reliable, valid, and relatively simple collection method to quantify THS contamination on surfaces across a wide range of field settings and to distinguish between nonsmoking and smoking environments.

  14. Metals Accumulation and Leaf Surface Anatomy of Murdannia spectabilis Growing in Zn/Cd Contaminated Soil

    Directory of Open Access Journals (Sweden)

    Ladawan Rattanapolsan

    2013-07-01

    Full Text Available Murdannia spectabilis (Kurz Faden was identified as a Zn/Cd hyperaccumulative plant. Leaf surface anatomy of the plant growing in non-contaminated soil (control and Zn/Cd contaminated soil,was studied and compared by a light microscopy and scanning electron microscopy combined with Energy-dispersive X-ray spectroscopy(SEM/EDS. The similarities were reticulate cuticle on epidermises, uniform polygonal cell, stomatal arrangement in six surrounding subsidiary cells, and submarginal sclerenchyma. The dissimilarities were uniserate trichomes spreading on both adaxial and abaxial epidermis of the plants growing in non-contaminated soil, whereas the uniserate trichomes were only on the submarginal-adaxial epidermis of the control plants. The trichomes on leaves of the plants growing in non-contaminated soil were found to have both uniseriate non-glandular and uniseriate glandular trichomes;whereas, leaves of the plants growing in the contaminated soil were merely non-glandular trichomes. The different shape and location of trichomes, the number of stomata and trichome indicated the effect of Zn and Cd on M. spectabilis. The higher percentages of Zn and Cd in the vascular bundle than in the cross section and epidermis areas showed both solutes could move along each route, with diffusion through the symplast and apoplast. The increase of Ca in M. spectabilis growing in Zn/Cd contaminated soil corresponded to the Zn and Cd distributed in the leaves. Zn K-edge and S K-edge XANES spectra proposed that Zn2+ ions were accumulated and/or adsorbed on the epidermis of the tuber, and then absorbed into the root and transport to the xylem. The double peaks of Zn-cysteine in the leaf samples proposed the metal sequestration was by sulphur proteins.

  15. Capacity building: benchmark for production of meat with low levels of bacterial contamination in local slaughterhouses in Somaliland.

    Science.gov (United States)

    Wamalwa, Kinyanjui; Castiello, Massimo; Ombui, Jackson Nyarangi; Gathuma, Joseph

    2012-03-01

    The objective of the study was to investigate and assess the impact of trainings on the levels of meat contamination produced from local livestock slaughter facilities in the North-West region of Somalia (Somaliland). The investigation considered slaughter facilities where workers had been trained or not. The survey was carried out in four local slaughter facilities. A pre-tested questionnaire on abattoir hygiene and food safety standards was administered to International Aid Organizations, government officials, abattoir workers and supervisors. In addition, a total of 320 surface meat swab samples were collected from randomly selected small ruminant carcasses slaughtered from four purposefully selected local slaughter facilities. The samples were analyzed at Analabs laboratories in Nairobi, Kenya, for total viable counts, total coliforms count and presence of Salmonella species. Meat contamination risk factors associated with hygiene practices based on training offered or not was identified. It was noted that slaughter facilities where abattoir workers had not received trainings on minimum meat hygiene standards and quality assurance systems of good hygiene practices and sanitary standard operating procedures produced carcasses with high levels of bacterial contamination in comparison with those where workers had received the said trainings. The laboratory results were in agreement with poor hygiene meat handling practices and lack of compliance with minimum meat hygiene and food safety standards in Berbera and Burao local livestock slaughter facilities where personnel had not been trained.

  16. Circulating levels of environmental contaminants are associated with dietary patterns in older adults.

    Science.gov (United States)

    Ax, Erika; Lampa, Erik; Lind, Lars; Salihovic, Samira; van Bavel, Bert; Cederholm, Tommy; Sjögren, Per; Lind, P Monica

    2015-02-01

    Food intake contributes substantially to our exposure to environmental contaminants. Still, little is known about our dietary habits' contribution to exposure variability. The aim of this study was to assess circulating levels of environmental contaminants in relation to predefined dietary patterns in an elderly Swedish population. Dietary data and serum concentrations of environmental contaminants were obtained from 844 70-year-old Swedish subjects (50% women) in the Prospective Investigation of the Vasculature in Uppsala Seniors (PIVUS) study. Dietary data from 7-day food records was used to assess adherence to a Mediterranean-like diet, a low carbohydrate-high protein diet and the WHO dietary recommendations. Circulating levels of 6 polychlorinated biphenyl markers, 3 organochlorine pesticides, 1 dioxin and 1 polybrominated diphenyl ether, the metals cadmium, lead, mercury and aluminum and serum levels of bisphenol A and 4 phthalate metabolites were investigated in relation to dietary patterns in multivariate linear regression models. A Mediterranean-like diet was positively associated with levels of several polychlorinated biphenyls (118, 126, 153, and 209), trans-nonachlor and mercury. A low carbohydrate-high protein diet was positively associated with polychlorinated biphenyls 118 and 153, trans-nonachlor, hexachlorobenzene and p, p'-dichlorodiphenyldichloroethylene, mercury and lead. The WHO recommended diet was negatively related to levels of dioxin and lead, and borderline positively to polychlorinated biphenyl 118 and trans-nonachlor. Dietary patterns were associated in diverse manners with circulating levels of environmental contaminants in this elderly Swedish population. Following the WHO dietary recommendations seems to be associated with a lower burden of environmental contaminants. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Organic Contaminant Levels in Three Fish Species Downchannel from the Los Alamos National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Gonzales, G.J.; Fresquez, P.R.; Beveridge, J.W.

    1999-06-01

    The LANL contribution, if any, to organic contaminant levels in the common carp, the channel catfish, and the white sucker in the Rio Grande appear to be small; however, low sample sizes, high variation, and potential interaction of species effect with location treatment effect require additional sampling and analysis.

  18. Nitrate and nitrite contamination of sub-surface water in some areas of North West Frontier Province (N.W.F.P.) Pakistan

    International Nuclear Information System (INIS)

    Khan, M.; Khawaja, M.A.; Imdadullah

    1998-01-01

    Over the past few years, nitrate and nitrite contamination of sub-surface water samples from Peshawar, Charsada, Mardan and Nowshera districts of NWFP has been studied. In all the areas under study, nitrate concentration of sub-surface water was found to be below WHO approved limit of 45 mg/l. Whereas city area after 1987 showed a decreasing level of nitrate contamination of sub-surface water, it appeared to be on the increase in water samples from the outskirts of Peshawar-Charsada road. No uniform increasing or decreasing patterns of nitrate contamination were observed for water samples from cantonment, University and Hayatabad, areas of Mardan, Charsada and Nowshera under study. The nitrate contamination of sub-surface water appeared to be due to both the agricultural activities as well as human and animal wastes. A few sub-surface water samples from Peshawar city, Mardan and Nowshera areas indicated high concentration of nitrite, which is alarming in view of the earlier reports showing absence of nitrite in water samples from these areas. However, since 1993, nitrite presence has not been detected in sub-surface water samples from all the areas under present investigation. (author)

  19. Oil contamination in surface sediment of Anzali Wetland in Iran is primarily even carbon number n-alkanes.

    Science.gov (United States)

    Azimi-Yancheshmeh, Rokhsareh; Riyahi-Bakhtiari, Alireza; Savabieasfahani, Mozhgan

    2017-10-29

    To determine the extent of oil contamination and biodegradation in Anzali Wetland of Iran, we examined aliphatic hydrocarbons in surface sediment of this area (n=20). Petroleum hydrocarbon levels (mean 1585 ± 1117; range 316 to 4358 μg g- 1 dry weight) were similar in value to reports from other highly contaminated areas, such as New York Bight, Saudi and Kuwaiti coasts of the Persian Gulf, and Dubai shorelines. Even carbon homologs dominated distribution of n-alkanes in surface sediment of Anzali, which is rarely reported elsewhere. Multiple factors used in our study point to petrogenic source for n-alkanes in Anzali Wetland. Anzali receives multiple industrial and agricultural runoffs from the surrounding area. Shipping industry and oil industry are responsible for a major portion of pollutants entering Anzali. Municipal wastewater discharges are another source of Anzali pollution. To determine why even carbon number n-alkanes predominate in Anzali, we examined the following indices: existence of unresolved complex mixtures (UCM), ratio of UCM to resolved alkanes (RA), ratio of low-molecular weight to high-molecular weight molecules, presence of degraded oil residue, high-relative biodegradation, and the degree of hydrocarbon weathering in the surface sediment of the area. Our findings corroborate with such predominance.

  20. Clearance of surface-contaminated objects from the controlled area of a nuclear facility. Application of the SUDOQU methodology

    Energy Technology Data Exchange (ETDEWEB)

    Russo, F.; Mommaert, C. [Bel V, Brussels (Belgium); Dillen, T. van [National Institute for Public Health and the Environment (RIVM), Bilthoven (Netherlands)

    2018-01-15

    The lack of clearly defined surface-clearance levels in the Belgian regulation led Bel V to start a collaboration with the Dutch National Institute for Public Health and the Environment (RIVM) to evaluate the applicability of the SUDOQU methodology for the derivation of nuclide-specific surface-clearance criteria for objects released from nuclear facilities. SUDOQU is a methodology for the dose assessment of exposure to a surface-contaminated object, with the innovative assumption of a time-dependent surface activity whose evolution is influenced by removal and deposition mechanisms. In this work, calculations were performed to evaluate the annual effective dose resulting from the use of a typical office item, e.g. a bookcase. Preliminary results allow understanding the interdependencies between the model's underlying mechanisms, and show a strong sensitivity to the main input parameters. The results were benchmarked against those from a model described in Radiation Protection 101, to investigate the impact of the model's main assumptions. Results of the two models were in good agreement. The SUDOQU methodology appears to be a flexible and powerful tool, suitable for the proposed application. Therefore, the project will be extended to more generic study cases, to eventually develop surface-clearance levels applicable to objects leaving nuclear facilities.

  1. Evaluation of surface contamination with cyclophosphamide following simulated hazardous drug preparation activities using two closed-system products.

    Science.gov (United States)

    Zock, Matthew D; Soefje, Scott; Rickabaugh, Keith

    2011-03-01

    A preliminary investigation was conducted to evaluate and compare the effectiveness of two closed-system products in preventing contamination of typical pharmacy workplace surfaces with cyclophosphamide during simulated hazardous drug preparation activities in a controlled laboratory setting. Two separate trials simulating hazardous drug compounding using cyclophosphamide were performed with two different closed-system products. Prior to each trial, work area surfaces of the biological safety cabinet (BSC) workbench, the BSC airfoil and front grill, and the floor below the BSC were cleaned, and wipe samples were collected and analyzed to determine, if present, levels of cyclophosphamide. Following each trial, wipe samples were collected from the work area surfaces to determine the hazardous drug containment effectiveness of each closed-system product. Cyclophosphamide was not detected on work area surfaces prior to each trial. Low levels were detected on the BSC workbench surface following both trials. Based on the limited number of samples obtained during this preliminary study and the determination of the presence of the chemical of interest on the drug vials, no statistical evaluation was performed to compare the relative effectiveness of the two systems tested. Work practices and procedures regarding product operation may affect hazardous drug containment and worker safety. Further study and statistical analyses are needed.

  2. A DEVICE TO MEASURE LOW LEVELS OF RADIOACTIVE CONTAMINANTS IN ULTRA-CLEAN MATERIALS

    International Nuclear Information System (INIS)

    James H Reeves; Matthew Kauer

    2006-01-01

    detector measuring 6 inch x 6 inch x 6 inch was fitted with wave length shifting fibers that allowed the light from ionizing radiation to be collected and transmitted outside the massive shield to photomultiplier tubes and electronics. The detector was calibrated for energy and detection efficiency and low resolution background spectra were collected. Results from these measurements show the figure of merit (using: efficiency/square root of background) for this plastic scintillation counting technique to be ∼15 times better than for a 2 kg germanium detector for measuring surface contamination from atmospheric 222Rn daughters (210Pb, 210Bi, and 210Po). These daughter radionuclides are normally deposited everywhere onto all materials exposed to air. The results are encouraging and indicate that plastic scintillation counting techniques can be of benefit to the public by making available very sensitive counters for screening ultra-low background materials at an affordable cost. However, in order to reach the level required a multi element array of thin plastic scintillator sheets must be developed that will allow many thin samples to be counted at one time. In addition, more sophisticated light detection hardware, electronics, and computer software is needed

  3. An investigation of fungal contamination on the surface of medicinal herbs in China.

    Science.gov (United States)

    Zheng, Run-Sheng; Wang, Wen-Li; Tan, Jing; Xu, Hui; Zhan, Ruo-Ting; Chen, Wei-Wen

    2017-01-01

    The dried parts of medicinal herbs are susceptible to the infection of fungi during pre- or post-harvest procedure. This study aimed to investigate the presence of fungi and their metabolites mycotoxins on the surface of medicinal herbs collected from China. Forty-five retail samples of 15 different medicinal herbs were collected from 3 different regions in China. Then the potential fungi were immediately washed off from the surface of each sample with 0.1% Tween-20 followed by incubation of the rinse on petri-dish with potato dextrose agar containing chloramphenicol at 28 °C. The obtained fungi were isolated as single colonies and then characterized by morphology and molecular identification using internal transcribed spacer (ITS) sequencing with extracted DNA. Meanwhile, the mycotoxin-producing potential of the isolates was studied by liquid chromatography-tandem mass spectrometry (LC-MS/MS). A total of 126 fungi were identified from the surface of samples by morphology and ITS sequencing, with Aspergillus and Penicillium genera as the predominant contaminants. The mycotoxin-producing potential analysis showed that 6 of 8 A. versicolor isolates could produce sterigmatocystin. All 3 A. aculeatus isolates produced ochratoxin A, but only 1 of 3 A. flavus strains produced aflatoxins B 1 and B 2 without G 1 and G 2 . Although the sample contamination ratios were high (≥95.6%), there was no significant difference ( χ 2  = 1.05, P  = 1.0) among the samples from 3 regions, which demonstrates the prevalent fungal contamination in the herbal medicines. The prevalent contamination phenomenon of fungi and high potential risk of sterigmatocystin and ochratoxin A were observed in 45 medicinal herbs collected from China.

  4. Study of the sediment contamination levels in a mangrove swamp polluted by a marine oil spill

    International Nuclear Information System (INIS)

    Wong, T.W.Y.; Ke, L.; Wong, Y.S.; Tam, N.F.Y.

    2002-01-01

    The pattern of oil retention in mangrove sediments was studied in an effort to determine the temporal changes of petroleum hydrocarbon concentrations and composition several months after oil spills occur. Mangroves are inter-tidal wetlands in tropical and subtropical coastlines. Due to the anoxic and water logging characteristics of mangrove sediments, oil residues linger much longer in these wetlands compared to other coastal habitats. In November 2000, an accidental oil spill occurred in the Pearl River Estuary in which approximately 230,000 litres of crude oil was leaked from an oil tanker. The spilled oil migrated to the YiO, a typical mangrove swamp in Hong Kong Special Administrative Region. The degree of oil contamination in the sediments depended on the sediment texture and topography of the mangrove. The total petroleum hydrocarbon (TPH) concentration of the sediments in the most affected area near a freshwater creek flowing into the sea was 130 times higher than normal, one month after the accident. The mean TPH concentration was 2862 ug/g of dry sediment while the mean carbon preference index was 1.22 compared to the background value of 3.97. The temporal changes of the petroleum hydrocarbon level in 5 defined areas were examined for 7 months after the spill. The most polluted area next to the creek was determined to have very high TPH levels in the muddy sediments even 7 months after the spill. Oil residues infiltrated as deep as 20 cm into the sediments, making it more difficult to degrade than surface pollution and posing long-term adverse effects on trees in the area. It was determined that with growing industrialization and increasing demands for fuel and energy supply, mangroves in South China should be ranked as top priority for protection from oil spills. 19 refs., 6 tabs., 6 figs

  5. Assessment of Soil-Gas, Surface-Water, and Soil Contamination at the Installation Railhead, Fort Gordon, Georgia, 2008-2009

    Science.gov (United States)

    Landmeyer, James E.; Harrelson, Larry G.; Ratliff, W. Hagan; Wellborn, John B.

    2010-01-01

    The U.S. Geological Survey, in cooperation with the U.S. Department of the Army Environmental and Natural Resources Management Office of the U.S. Army Signal Center and Fort Gordon, assessed soil gas, surface water, and soil for contaminants at the Installation Railhead (IR) at Fort Gordon, Georgia, from October 2008 to September 2009. The assessment included delineation of organic contaminants present in soil-gas samples beneath the IR, and in a surface-water sample collected from an unnamed tributary to Marcum Branch in the western part of the IR. Inorganic contaminants were determined in a surface-water sample and in soil samples. This assessment was conducted to provide environmental contamination data to Fort Gordon personnel pursuant to requirements of the Resource Conservation and Recovery Act Part B Hazardous Waste Permit process. Soil-gas samples collected within a localized area on the western part of the IR contained total petroleum hydrocarbons; benzene, toluene, ethylbenzene, and total xylenes (referred to as BTEX); and naphthalene above the method detection level. These soil-gas samples were collected where buildings had previously stood. Soil-gas samples collected within a localized area contained perchloroethylene (PCE). These samples were collected where buildings 2410 and 2405 had been. Chloroform and toluene were detected in a surface-water sample collected from an unnamed tributary to Marcum Branch but at concentrations below the National Primary Drinking Water Standard maximum contaminant level (MCL) for each compound. Iron was detected in the surface-water sample at 686 micrograms per liter (ug/L) and exceeded the National Secondary Drinking Water Standard MCL for iron. Metal concentrations in composite soil samples collected at three locations from land surface to a depth of 6 inches did not exceed the U.S. Environmental Protection Agency Regional Screening Levels for industrial soil.

  6. Contaminant levels in eggs of American white pelicans, Pelecanus erythrorhynchos, from Chase Lake, North Dakota

    Science.gov (United States)

    Pietz, Pamela J.; Sovada, Marsha A.; Custer, Christine M.; Custer, Thomas W.; Johnson, Kevin M.

    2008-01-01

    American White Pelicans (Pelecanus erythrorhynchos) are colonial nesters, making them susceptible to site-specific mortality factors. One of the largest known breeding colonies is at Chase Lake National Wildlife Refuge in North Dakota. In 2004, this colony suffered total reproductive failure. In 2005, we collected abandoned eggs from this colony to test for environmental contaminants. Nine eggs were analyzed for 28 organochlorine pesticides, total polychlorinated biphenyls, and 26 inorganic elements. Based on concentrations in this sample of eggs and levels linked to reproductive problems in birds, adult pelicans in the Chase Lake breeding colony are not at known risk from any of the environmental contaminants we measured.

  7. The effect of soil contamination level on risk element uptake by chamomile (Matricaria recutita (L.) Rauschert)

    International Nuclear Information System (INIS)

    Dziakova, M.; Szakova, J.; Vildova, A.; Tlustos, P.

    2009-01-01

    Full text: German chamomile (Matricaria recutita (L.) Rauschert) belongs to the plants characterized by high tolerance to toxic elements, especially cadmium. The ability of German chamomile to accumulate potentially risk elements was tested in a pot experiment where soils contaminated by different levels of As, Cd, Pb, and Zn were applied. Whereas As, Pb, and Zn retained in roots, cadmium showed a good ability to translocate to aboveground biomass including flowers even at extremely cadmium contaminated soil without symptoms of its phytotoxicity. Between 5.5 and 80 % of total Cd was released to infusion and its extractability decreased with increasing Cd content in flowers. (author)

  8. Using Contaminant Transport Modeling to Determine Historical Discharges at the Surface

    Science.gov (United States)

    Fogwell, T. W.

    2013-12-01

    When it is determined that a contaminated site needs to be remediated, the issue of who is going to pay for that remediation is an immediate concern. This means that there needs to be a determination of who the responsible parties are for the existing contamination. Seldom is it the case that records have been made and kept of the surface contaminant discharges. In many cases it is possible to determine the relative amount of contaminant discharge at the surface of the various responsible parties by employing a careful analysis of the history of contaminant transport through the surface, through the vadose zone, and within the saturated zone. The process begins with the development of a dynamic conceptual site model that takes into account the important features of the transport of the contaminants through the vadose zone and in the groundwater. The parameters for this model can be derived from flow data available for the site. The resulting contaminant transport model is a composite of the vadose zone transport model, together with the saturated zone (groundwater) flow model. Any calibration of the model should be carefully employed in order to avoid using information about the conclusions of the relative discharge amounts of the responsible parties in determining the calibrated parameters. Determination of the leading edge of the plume is an important first step. It is associated with the first discharges from the surface of the site. If there were several discharging parties at the same time, then it is important to establish a chemical or isotopic signature of the chemicals that were discharged. The time duration of the first discharger needs to be determined as accurately as possible in order to establish the appropriate characterization of the leading portion of the resulting plume in the groundwater. The information about the first discharger and the resulting part of the plume associated with this discharger serves as a basis for the determination of the

  9. Resistance to disinfection of a polymicrobial association contaminating the surface of elastomeric dental impressions.

    Science.gov (United States)

    Giammanco, Giovanni M; Melilli, Dario; Rallo, Antonio; Pecorella, Sonia; Mammina, Caterina; Pizzo, Giuseppe

    2009-04-01

    The aim of this study was to evaluate the ability to resist disinfection of a polymicrobial association contaminating the surface of dental impressions obtained with two different elastomers: a polyether (Impregum) and an addition-polymerized silicone (Elite). Impressions were contaminated with a mixture of three biofilm-forming microorganisms (Staphylococcus aureus, Pseudomonas aeruginosa and Candida albicans) and disinfected immediately after contamination, or after microbial layers were allowed to develop during a six-hour storage. Two commercial disinfectants were tested: MD 520 containing 0.5% glutaraldehyde and Sterigum Powder without glutaraldehyde. Residual contamination was recovered by mechanical rinsing immediately after disinfection and after a six-hour storage of disinfected impressions, and assessed by colony counting. Both disinfectants tested were shown to be effective in reducing the microbial presence on the impression materials, achieving at least a 102 reduction of microbial counts compared to water rinsing. However, Sterigum was generally less effective on the Elite elastomer and could not grant disinfection on six-hour aged P. aeruginosa and C. albicans microbial layers. The results of this study suggest that the materials used for the impressions influence the efficacy of disinfection. Disinfectants should be tested according to conditions encountered in everyday clinical practice and the need for immediate disinfection of impressions should be clearly indicated by manufacturers.

  10. Occurrence and behavior of emerging contaminants in surface water and a restored wetland.

    Science.gov (United States)

    Matamoros, Víctor; Arias, Carlos A; Nguyen, Loc Xuan; Salvadó, Victòria; Brix, Hans

    2012-08-01

    Pollution mitigation is an important target for restored wetlands, and although there is much information in relation to nutrient removal, little attention has been paid to emerging contaminants. This paper reports on the occurrence and attenuation capacity of 17 emerging contaminants in a restored wetland and two rivers in North-East Denmark. The compounds belong to the groups of pharmaceuticals, fragrances, antiseptics, fire retardants, pesticides, and plasticizers. Concentrations in surface waters ranged from 2 to 1476 ng L(-1). The compounds with the highest concentrations were diclofenac, 2-methyl-4-chlorophenoxyacetic acid (MCPA), caffeine, and tris(2-chloroethyl) phosphate (TCEP). The herbicide concentrations increased after a rain-fall event, demonstrating the agricultural run-off origin of these compounds, whereas the concentration of the other emerging contaminants was rather conservative. The mitigation capacity of the restored wetland for the compounds ranged from no attenuation to 84% attenuation (19% on average). Hence, restored wetlands may be considered as a feasible alternative for mitigating emerging contaminants from river waters. Copyright © 2012 Elsevier Ltd. All rights reserved.

  11. Uptake of radionuclides by wheat roots with respect to location of contamination below the surface

    International Nuclear Information System (INIS)

    Suvornmongkhol, Narumon.

    1996-01-01

    The behaviour of 85 Sr, 137 Cs, 54 Mn and 60 Co in terms of plant availability in near surface soil and their root uptake was studied as a function of the location of contamination in the soil profile. Wheat (Triticum aestivum) was employed and the study programme involved both column and hydroponic studies. In the column studies, columns were packed with sandy soil, and either homogeneously or discretely contaminated with the radionuclides, and the water table maintained manually at 3 cm from the bottom. In the discrete contamination, the location of contamination was varied (0-5, 25-30 or 45-50 cm from the top). Wheat plants were grown to maturity in these columns, and harvested at different growth stages to examine radioactivity uptake and its subsequent translocation within the plants. The movement of radionuclides within the soil as well as the soil physicochemical properties were also investigated. The short term uptake kinetics of the hydroponically grown plants during ontogenesis were also studied, both with excised roots and intact plants. The excised root experiment was aimed at investigating the radionuclide by roots of different orders. (author)

  12. A survey of Cr(VI) contamination of surface water in the proximity of ...

    African Journals Online (AJOL)

    In this study, Cr(VI) levels present in surface water within the vicinity of ferrochrome smelters located in the Bushveld Igneous Complex were monitored for a period of 1 year. The results indicated that surface water in the proximity of ferrochrome smelters was mostly unaffected by Cr(VI) pollution. Two surface water sampling ...

  13. Changes in contaminant levels in New Jersey osprey eggs and prey, 1989 to 1998.

    Science.gov (United States)

    Clark, K E; Stansley, W; Niles, L J

    2001-02-01

    Ospreys are good indicators of the health of estuarine areas because they feed almost exclusively on fish with the balance on other aquatic biota. Through the 1980s, ospreys nesting on Delaware Bay in New Jersey had reduced reproductive success relative to those nesting on the Atlantic coast and the Maurice River, a tributary of Delaware Bay. Earlier research suggested that elevated levels of DDT and polychlorinated biphenyl (PCB) contaminants identified in addled osprey eggs contributed to this reduced productivity. We repeated egg and prey sampling initially conducted in 1989 to evaluate the trends of contaminants in the last decade. Most organochlorine contaminants declined in osprey eggs in 1998 relative to 1989. Across three study areas, PCBs decreased from 4.1-7.7 ppm in 1989 to 1.8-3.2 ppm in 1998; DDE decreased from 1.2-3.2 ppm in 1989 to 0.7-1.2 ppm in 1998. Lead in eggs increased from an average of 0.01 to 0.30 ppm wet weight, and mercury averaged 0.12 ppm and increased only in Atlantic coast eggs. Most of these contaminant changes were also found in typical prey fish: PCBs decreased from 0.18-1.2 ppm in 1989 to 0.06-0.43 ppm in 1998; DDE decreased from 0.05-0.69 ppm in 1989 to 0.03-0.13 ppm in 1998. Lead and mercury increased in most fish samples. The improvement in most organochlorine contaminants in osprey eggs and prey reflected improved nest success in the Delaware Bay study area, and the nesting populations in the Atlantic and Maurice River study areas increased approximately 200% since 1989. PCBs and DDE in osprey eggs were below levels considered to be toxic to egg development. This study documents significant improvements in organochlorine contaminants in southern New Jersey ospreys, but justifies continued monitoring of heavy metals, such as lead and mercury, in aquatic ecosystems.

  14. Removal of contaminated concrete surfaces by microwave heating: Phase 1 results

    International Nuclear Information System (INIS)

    White, T.L.; Grubb, R.G.; Pugh, L.P.; Foster, D. Jr.; Box, W.D.

    1992-01-01

    Oak Ridge National Laboratory (ORNL) is developing a microwave heating process to remove radiologically contaminated surface layers from concrete. The microwave energy is directed at the concrete surface and heats the concrete and free water present in the concrete matrix. Continued heating produces steam-pressure-induced mechanical stresses that cause the concrete surface to burst. The concrete particles from this steam explosion are small enough to be removed by a vacuum system, yet less than 1% of the debris is small enough to pose an airborne contamination hazard. The first phase of this program has demonstrated reliable removal of noncontaminated concrete surfaces at frequencies of 2.45 GHz and 10.6 GHz. Continuous concrete removal rates of 1.07 cm 3 /s with 5.2 kW of 2.45.-GHz power and 2.11 cm 3 /s with 3.6 kW of 10.6-GHz power have been demonstrated. Figures-of-merit for microwave removal of concrete have been calculated to be 0.21 cm 3 /s/kW at 2.45 GHz and 0.59 cm 3 /s/kW at 10.6 GHz. The amount of concrete removed in a single pass can be controlled by choosing the frequency and power of the microwave system

  15. Suitability of artificial sweeteners as indicators of raw wastewater contamination in surface water and groundwater.

    Science.gov (United States)

    Tran, Ngoc Han; Hu, Jiangyong; Li, Jinhua; Ong, Say Leong

    2014-01-01

    There is no quantitative data on the occurrence of artificial sweeteners in the aquatic environment in Southeast Asian countries, particularly no information on their suitability as indicators of raw wastewater contamination on surface water and groundwater. This study provided the first quantitative information on the occurrence of artificial sweeteners in raw wastewater, surface water and groundwater in the urban catchment area in Singapore. Acesulfame, cyclamate, saccharin, and sucralose were ubiquitous in raw wastewater samples at concentrations in the range of ng/L-μg/L, while other sweeteners were not found or found only in a few of the raw wastewater samples. Residential and commercial effluents were demonstrated to be the two main sources of artificial sweeteners entering the municipal sewer systems. Relatively higher concentrations of the detected sweeteners were frequently found in surface waters at the sampling sites located in the residential/commercial areas. No significant difference in the concentrations of the detected sweeteners in surface water or groundwater was noted between wet and dry weather conditions (unpaired T-test, p> 0.05). Relatively higher concentrations and detection frequencies of acesulfame, cyclamate and saccharin in surface water samples were observed at the potentially impacted sampling sites, while these sweeteners were absent in most of the background surface water samples. Similarly, acesulfame, cyclamate, and saccharin were found in most groundwater samples at the monitoring well (GW6), which is located close to known leaking sewer segment; whereas these were absent in the background monitoring well, which is located in the catchment with no known wastewater sources. Taken together, the results suggest that acesulfame, cyclamate, and saccharin can be used as potential indicators of raw wastewater contamination in surface water and groundwater. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Vulnerability of drinking-water wells in La Crosse, Wisconsin, to enteric-virus contamination from surface water contributions

    Science.gov (United States)

    Borchardt, M. A.; Haas, N.L.; Hunt, R.J.

    2004-01-01

    Human enteric viruses can contaminate municipal drinking-water wells, but few studies have examined the routes by which viruses enter these wells. In the present study, the objective was to monitor the municipal wells of La Crosse, Wisconsin, for enteric viruses and determine whether the amount of Mississippi River water infiltrating the wells was related to the frequency of virus detection. From March 2001 to February 2002, one river water site and four wells predicted by hydrogeological modeling to have variable degrees of surface water contributions were sampled monthly for enteric viruses, microbial indicators of sanitary quality, and oxygen and hydrogen isotopes. 18O/ 16O and 2H/1H ratios were used to determine the level of surface water contributions. All samples were collected prior to chlorination at the wellhead. By reverse transcription-PCR (RT-PCR), 24 of 48 municipal well water samples (50%) were positive for enteric viruses, including enteroviruses, rotavirus, hepatitis A virus (HAV), and noroviruses. Of 12 river water samples, 10 (83%) were virus positive by RT-PCR. Viable enteroviruses were not detected by cell culture in the well samples, although three well samples were positive for culturable HAV. Enteroviruses detected in the wells by RT-PCR were identified as several serotypes of echoviruses and group A and group B coxsackieviruses. None of the well water samples was positive for indicators of sanitary quality, namely male-specific and somatic coliphages, total coliform bacteria, Escherichia coli, and fecal enterococci. Contrary to expectations, viruses were found in all wells regardless of the level of surface water contributions. This result suggests that there were other unidentified sources, in addition to surface water, responsible for the contamination.

  17. Innovative technology for expedited site remediation of extensive surface and subsurface contamination

    International Nuclear Information System (INIS)

    Audibert, J.M.E.; Lew, L.R.

    1994-01-01

    Large scale surface and subsurface contamination resulted from numerous releases of feed stock, process streams, waste streams, and final product at a major chemical plant. Soil and groundwater was contaminated by numerous compounds including lead, tetraethyl lead, ethylene dibromide, ethylene dichloride, and toluene. The state administrative order dictated that the site be investigated fully, that remedial alternative be evaluated, and that the site be remediated within a year period. Because of the acute toxicity and extreme volatility of tetraethyl lead and other organic compounds present at the site and the short time frame ordered by the regulators, innovative approaches were needed to carry out the remediation while protecting plant workers, remediation workers, and the public

  18. Campylobacter jejuni contamination of broiler carcasses: Population dynamics and genetic profiles at slaughterhouse level.

    Science.gov (United States)

    Gruntar, Igor; Biasizzo, Majda; Kušar, Darja; Pate, Mateja; Ocepek, Matjaž

    2015-09-01

    Six slaughter batches deriving from six typical industrial broiler flocks were examined for the presence, quantity and genetic characteristics of contaminating Campylobacter jejuni (C. jejuni) during various stages of slaughtering and carcass processing. To assess the contamination dynamics of the carcasses, the analyses were always conducted on neck-skin samples from the same pre-selected and carefully marked carcasses in each batch. The skin samples were taken sequentially at three successive slaughter-line locations in the evisceration room, after three-day refrigeration and after three-day freezing procedure. Caecal samples from the same animals were also tested, as well as samples from the slaughterhouse environment before and after slaughtering. The samples were analysed by the ISO10272 isolation method; campylobacters from neck-skin samples were also quantified. Isolates were species-identified and genotyped by pulsed-field gel electrophoresis (PFGE). On average, the highest C. jejuni skin contamination was detected at the first sampling point (post-plucking), suggesting that the majority of Campylobacter contamination actually occurs before the entrance to the eviscerating room, probably during the preceding plucking stage. In two out of five positive batches, an additional increase in contamination was recorded after the evisceration step. An evident trend of increasing contamination level was detected when successive batches were compared at each of two initial sampling sites in the evisceration room, indicating an accumulation of contaminating C. jejuni at some point before the evisceration room. Three-day refrigeration and three-day freezing caused a 4.5- and 142-fold drop in mean C. jejuni CFU counts, respectively. All pre-slaughtering samples from the slaughterhouse environment were negative and all post-slaughtering samples, except water from the scalding tank, were positive. Pulsotypes were limited: altogether five different types were detected

  19. Advanced LWIR hyperspectral sensor for on-the-move proximal detection of liquid/solid contaminants on surfaces

    Science.gov (United States)

    Giblin, Jay P.; Dixon, John; Dupuis, Julia R.; Cosofret, Bogdan R.; Marinelli, William J.

    2017-05-01

    Sensor technologies capable of detecting low vapor pressure liquid surface contaminants, as well as solids, in a noncontact fashion while on-the-move continues to be an important need for the U.S. Army. In this paper, we discuss the development of a long-wave infrared (LWIR, 8-10.5 μm) spatial heterodyne spectrometer coupled with an LWIR illuminator and an automated detection algorithm for detection of surface contaminants from a moving vehicle. The system is designed to detect surface contaminants by repetitively collecting LWIR reflectance spectra of the ground. Detection and identification of surface contaminants is based on spectral correlation of the measured LWIR ground reflectance spectra with high fidelity library spectra and the system's cumulative binary detection response from the sampled ground. We present the concepts of the detection algorithm through a discussion of the system signal model. In addition, we present reflectance spectra of surfaces contaminated with a liquid CWA simulant, triethyl phosphate (TEP), and a solid simulant, acetaminophen acquired while the sensor was stationary and on-the-move. Surfaces included CARC painted steel, asphalt, concrete, and sand. The data collected was analyzed to determine the probability of detecting 800 μm diameter contaminant particles at a 0.5 g/m2 areal density with the SHSCAD traversing a surface.

  20. Geochemical baseline level and function and contamination of phosphorus in Liao River Watershed sediments of China.

    Science.gov (United States)

    Liu, Shaoqing; Wang, Jing; Lin, Chunye; He, Mengchang; Liu, Xitao

    2013-10-15

    The quantitative assessment of P contamination in sediments is a challenge due to sediment heterogeneity and the lacking of geochemical background or baseline levels. In this study, a procedure was proposed to determine the average P background level and P geochemical baseline level (GBL) and develop P geochemical baseline functions (GBF) for riverbed sediments of the Liao River Watershed (LRW). The LRW has two river systems - the Liao River System (LRS) and the Daliao River System (DRS). Eighty-eight samples were collected and analyzed for P, Al, Fe, Ca, organic matter, pH, and texture. The results show that Fe can be used as a better particle-size proxy to construct the GBF of P (P (mg/kg) = 39.98 + 166.19 × Fe (%), R(2) = 0.835, n = 66). The GBL of P was 675 mg/kg, while the average background level of P was 355 mg/kg. Noting that many large cities are located in the DRS watershed, most of the contaminated sites were located within the DRS and the riverbed sediments were more contaminated by P in the DRS watershed than in the LRS watershed. The geochemical background and baseline information of P are of great importance in managing P levels within the LRW. Copyright © 2013 Elsevier Ltd. All rights reserved.

  1. Surface tailored organobentonite enhances bacterial proliferation and phenanthrene biodegradation under cadmium co-contamination

    Energy Technology Data Exchange (ETDEWEB)

    Mandal, Asit [Future Industries Institute (formerly Centre for Environmental Risk Assessment and Remediation), University of South Australia, Mawson Lakes, SA 5095 (Australia); Indian Council of Agricultural Research (ICAR), Indian Institute of Soil Science, Bhopal (India); Biswas, Bhabananda [Future Industries Institute (formerly Centre for Environmental Risk Assessment and Remediation), University of South Australia, Mawson Lakes, SA 5095 (Australia); Cooperative Research Centre for Contamination Assessment and Remediation of the Environment (CRC CARE), ACT Building, University of Newcastle, Callaghan, NSW 2308 (Australia); Sarkar, Binoy, E-mail: binoy.sarkar@unisa.edu.au [Future Industries Institute (formerly Centre for Environmental Risk Assessment and Remediation), University of South Australia, Mawson Lakes, SA 5095 (Australia); Cooperative Research Centre for Contamination Assessment and Remediation of the Environment (CRC CARE), ACT Building, University of Newcastle, Callaghan, NSW 2308 (Australia); Patra, Ashok K. [Indian Council of Agricultural Research (ICAR), Indian Institute of Soil Science, Bhopal (India); Naidu, Ravi, E-mail: ravi.naidu@newcastle.edu.au [Cooperative Research Centre for Contamination Assessment and Remediation of the Environment (CRC CARE), ACT Building, University of Newcastle, Callaghan, NSW 2308 (Australia); Global Centre for Environmental Remediation (GCER), Faculty of Science and Information Technology, University of Newcastle, Callaghan, NSW 2308 (Australia)

    2016-04-15

    Co-contamination of soil and water with polycyclic aromatic hydrocarbon (PAH) and heavy metals makes biodegradation of the former extremely challenging. Modified clay-modulated microbial degradation provides a novel insight in addressing this issue. This study was conducted to evaluate the growth and phenanthrene degradation performance of Mycobacterium gilvum VF1 in the presence of a palmitic acid (PA)-grafted Arquad® 2HT-75-based organobentonite in cadmium (Cd)-phenanthrene co-contaminated water. The PA-grafted organobentonite (ABP) adsorbed a slightly greater quantity of Cd than bentonite at up to 30 mg L{sup −1} metal concentration, but its highly negative surface charge imparted by carboxylic groups indicated the potential of being a significantly superior adsorbent of Cd at higher metal concentrations. In systems co-contained with Cd (5 and 10 mg L{sup −1}), the Arquad® 2HT-75-modified bentonite (AB) and PA-grafted organobentonite (ABP) resulted in a significantly higher (72–78%) degradation of phenanthrene than bentonite (62%) by the bacterium. The growth and proliferation of bacteria were supported by ABP which not only eliminated Cd toxicity through adsorption but also created a congenial microenvironment for bacterial survival. The macromolecules produced during ABP–bacteria interaction could form a stable clay-bacterial cluster by overcoming the electrostatic repulsion among individual components. Findings of this study provide new insights for designing clay modulated PAH bioremediation technologies in mixed-contaminated water and soil. - Highlights: • Surface tailored organobentonite synthesised and characterised • Modified clay adsorbs Cd and reduces toxicity to Mycobacterium gilvum. • It creates congenial microenvironment for bacterial survival. • It enhances phenanthrene biodegradation in metal co-contaminated condition.

  2. Visible-light system for detecting doxorubicin contamination on skin and surfaces.

    Science.gov (United States)

    Van Raalte, J; Rice, C; Moss, C E

    1990-05-01

    A portable system that uses fluorescence stimulated by visible light to identify doxorubicin contamination on skin and surfaces was studied. When activated by violet-blue light in the 465-nm range, doxorubicin fluoresces, emitting orange-red light in the 580-nm range. The light source to stimulate fluorescence was a slide projector with a filter to selectively pass short-wave (blue) visible light. Fluorescence was both observed visually with viewing spectacles and photographed. Solutions of doxorubicin in sterile 0.9% sodium chloride injection were prepared in nine standard concentrations ranging from 2 to 0.001 mg/mL. Droplets of each admixture were placed on stainless steel, laboratory coat cloth, pieces of latex examination glove, bench-top absorbent padding, and other materials on which antineoplastics might spill or leak. These materials then were stored for up to eight weeks and photographed weekly. The relative ability of water, household bleach, hydrogen peroxide solution, and soap solution to deactivate doxorubicin was also measured. Finally, this system was used to inspect the antineoplastic-drug preparation and administration areas of three outpatient cancer clinics for doxorubicin contamination. Doxorubicin fluorescence was easily detectable with viewing spectacles when a slide projector was used as the light source. The photographic method was sensitive for doxorubicin concentrations from 2.0 to 0.001 mg/mL. Immersion of study materials in bleach for one minute eliminated detectable fluorescence. Doxorubicin contamination is detectable for at least eight weeks in the ambient environment. Probable doxorubicin contamination was detected in two of the three clinics surveyed. A safe, portable system that uses fluorescence stimulated by visible light is a sensitive method for detecting doxorubicin on skin and surfaces.

  3. Identification of risk factors for Campylobacter contamination levels on broiler carcasses during the slaughter process.

    Science.gov (United States)

    Seliwiorstow, Tomasz; Baré, Julie; Berkvens, Dirk; Van Damme, Inge; Uyttendaele, Mieke; De Zutter, Lieven

    2016-06-02

    Campylobacter carcass contamination was quantified across the slaughter line during processing of Campylobacter positive batches. These quantitative data were combined together with information describing slaughterhouse and batch related characteristics in order to identify risk factors for Campylobacter contamination levels on broiler carcasses. The results revealed that Campylobacter counts are influenced by the contamination of incoming birds (both the initial external carcass contamination and the colonization level of caeca) and the duration of transport and holding time that can be linked with feed withdrawal period. In addition, technical aspects of the slaughter process such as a dump based unloading system, electrical stunning, lower scalding temperature, incorrect setting of plucking, vent cutter and evisceration machines were identified as risk factors associated with increased Campylobacter counts on processed carcasses. As such the study indicates possible improvements of the slaughter process that can result in better control of Campylobacter numbers under routine processing of Campylobacter positive batches without use of chemical or physical decontamination. Moreover, all investigated factors were existing variations of the routine processing practises and therefore proposed interventions are practically and economically achievable. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. 131I levels in cow's milk following ingestion of contaminated alfalfa or sudan grass

    International Nuclear Information System (INIS)

    Black, S.C.; Stanley, R.E.; Barth, D.S.

    1975-08-01

    A dry aerosol, consisting of submicrometer diatomaceous earth particles tagged with 131 I, was released over two different types of growing forage (alfalfa and Sudan grass) at the Experimental Dairy Farm on the Nevada Test Site. Following deposition of the aerosol, the two forage types were chopped and fed to different groups of lactating dairy cows. The dual objectives of the study were to evaluate the relationship of 131 I secretion in milk to the ingestion of different types of contaminated forage and to obtain a further indication of the possible influence on milk radioiodine levels of changing the particle size of the contaminant. The ratios of the peak activity concentrations measured in the milk to the peak activity concentrations in the forage were computed to be 0.0145 for the cows fed contaminated alfalfa and 0.0082 for those fed contaminated Sudan grass. Comparison of the results from this study with those from earlier studies indicates the major effect on activity levels in the milk can be related to forage type. Ingestion of Sudan grass by the cow reduces the transfer of radioiodine to milk by one half compared to ingestion of alfalfa. (U.S.)

  5. Effectiveness of disinfection with alcohol 70% (w/v of contaminated surfaces not previously cleaned

    Directory of Open Access Journals (Sweden)

    Maurício Uchikawa Graziano

    Full Text Available OBJECTIVE: To evaluate the disinfectant effectiveness of alcohol 70% (w/v using friction, without previous cleaning, on work surfaces, as a concurrent disinfecting procedure in Health Services. METHOD: An experimental, randomized and single-blinded laboratory study was undertaken. The samples were enamelled surfaces, intentionally contaminated with Serratia marcescens microorganisms ATCC 14756 106 CFU/mL with 10% of human saliva added, and were submitted to the procedure of disinfection WITHOUT previous cleaning. The results were compared to disinfection preceded by cleaning. RESULTS: There was a reduction of six logarithms of the initial microbial population, equal in the groups WITH and WITHOUT previous cleaning (p=0.440 and a residual microbial load ≤ 102 CFU. CONCLUSION: The research demonstrated the acceptability of the practice evaluated, bringing an important response to the area of health, in particular to Nursing, which most undertakes procedures of concurrent cleaning /disinfecting of these work surfaces.

  6. Effectiveness of disinfection with alcohol 70% (w/v of contaminated surfaces not previously cleaned

    Directory of Open Access Journals (Sweden)

    Maurício Uchikawa Graziano

    2013-04-01

    Full Text Available OBJECTIVE: To evaluate the disinfectant effectiveness of alcohol 70% (w/v using friction, without previous cleaning, on work surfaces, as a concurrent disinfecting procedure in Health Services. METHOD: An experimental, randomized and single-blinded laboratory study was undertaken. The samples were enamelled surfaces, intentionally contaminated with Serratia marcescens microorganisms ATCC 14756 106 CFU/mL with 10% of human saliva added, and were submitted to the procedure of disinfection WITHOUT previous cleaning. The results were compared to disinfection preceded by cleaning. RESULTS: There was a reduction of six logarithms of the initial microbial population, equal in the groups WITH and WITHOUT previous cleaning (p=0.440 and a residual microbial load ≤ 102 CFU. CONCLUSION: The research demonstrated the acceptability of the practice evaluated, bringing an important response to the area of health, in particular to Nursing, which most undertakes procedures of concurrent cleaning /disinfecting of these work surfaces.

  7. Contamination by urban superficial runoff: accumulated heavy metals on a road surface

    Directory of Open Access Journals (Sweden)

    Carlos Alfonso Zafra Mejía

    2007-01-01

    Full Text Available Studying the behaviour of accumulated contamination on urban surfaces is important in designing control methods minimising the impacts of surface runoff on the environment. This paper presents data regarding the sediment collected on the surface of an urban road in the city of Torrelavega in northern Spain during a period of 65 days during which 132 samples were collected. Two types of sediment collection samples were obtained: vacuumed dry samples (free load and those swept up following vacuuming (fixed load. The results showed that heavy metal concentration in the collected sediment (Pb, Zn, Cu and Cd was inversely proportional to particle diameter. High heavy metal concentrations were found in the smaller fraction (63 pm. Regression equations were calculated for heavy metal concentration regarding particle diameter. Large heavy metal loads were found in the larger fraction (125 pm. The results provide information for analysing runoff water quality in urban areas and designing treatment strategies.

  8. Optical Interferometry with Flexible Coherent Fiber Bundle for Measuring Deposits or Contamination on Surfaces and Inside Tubes

    Data.gov (United States)

    National Aeronautics and Space Administration — A new measuring/cleaning method for closed surfaces (pipes) applicable to removing contaminants (oil films, fungus, rust) from NASA instruments and spacecraft is...

  9. Current levels and trends of radioactive contamination of aquatic ecosystem components in the Chernobyl exclusion zone

    Energy Technology Data Exchange (ETDEWEB)

    Gudkov, Dmitri I.; Kaglyan, Alexander Ye.; Ganzha, Kristina D.; Klenus, Vasiliy G. [Institute of Hydrobiology, Geroyev Stalingrada Ave. 12, UA-04210 Kiev (Ukraine); Kireev, Sergey I.; Nazarov, Alexander B. [Chernobyl Specialized Enterprise, Radyanska Str. 70, UA-07270 Chernobyl (Ukraine)

    2014-07-01

    The current radiation level and its composition in aquatic ecosystems within the Chernobyl exclusion zone (ChEZ) are conditioned, above all things, by the amount of radioactive matters released as aerosols on a water surface and adjacent territories during the period of the active phase of the accident from destroyed of the Chernobyl NPP in 1986, and also by intensity and duration of the second processes of radionuclides washout from the catchment areas and hydrodynamic processes of their transport outside of water bodies. During last 10-15 years in the soils of the ChEZ the tendency of increase of yield of the mobile bioavailable forms of radionuclides, which released into hydrological systems with surface and ground waters or localized in the closed water systems, where quickly involving in the biotic cycle is marked. On the example of lakes of the Krasnensky flood plain of the Pripyat River, which is one of the most contaminated by radionuclides territory of the ChEZ, was determined that the basic amount of radionuclides in lake ecosystem is deposited in the bottom sediments: {sup 90}Sr - 89-95%, {sup 137}Cs - 99%, transuranium elements (TUE) {sup 238}Pu, {sup 239+240}Pu and {sup 241}Am - almost 100% of the total radionuclide amount in ecosystem. The increased migration activity of {sup 90}Sr determines its more high quantity in water (4-10%) on comparison with {sup 137}Cs (0.5-0.6%) and TUE (0.03-0.04%) and, opposite, less - in seston (0.15-0.16%) on comparison with {sup 137}Cs (0.25-0.30%). The value of {sup 90}Sr in biotic component amounts 0.25-0.61%, {sup 137}Cs - 0.14-0.47% and TUE - 0.07-0.16% of the total quantity in ecosystem. The gradual decline of radionuclide specific activity is a dominant tendency in the dynamics of {sup 137}Cs and {sup 90}Sr in water and aquatic biota of the majority of reservoirs and water flow in the ChEZ. The exception is water bodies, located on the dammed territories of the Krasnensky flood plain, where at the proceeding

  10. Impact of cadmium contamination and oxygenation levels on biochemical responses in the Asiatic clam Corbicula fluminea

    Energy Technology Data Exchange (ETDEWEB)

    Legeay, Alexia [Laboratoire d' Ecophysiologie et Ecotoxicologie des Systemes Aquatiques (LEESA), UMR 5805-OASU, Universite Bordeaux 1 and CNRS, Place Peyneau, 33120 Arcachon (France)]. E-mail: a.legeay@epoc.u-bordeaux1.fr; Achard-Joris, Maud [Laboratoire d' Ecophysiologie et Ecotoxicologie des Systemes Aquatiques (LEESA), UMR 5805-OASU, Universite Bordeaux 1 and CNRS, Place Peyneau, 33120 Arcachon (France); Baudrimont, Magalie [Laboratoire d' Ecophysiologie et Ecotoxicologie des Systemes Aquatiques (LEESA), UMR 5805-OASU, Universite Bordeaux 1 and CNRS, Place Peyneau, 33120 Arcachon (France); Massabuau, Jean-Charles [Laboratoire d' Ecophysiologie et Ecotoxicologie des Systemes Aquatiques (LEESA), UMR 5805-OASU, Universite Bordeaux 1 and CNRS, Place Peyneau, 33120 Arcachon (France); Bourdineaud, Jean-Paul [Laboratoire d' Ecophysiologie et Ecotoxicologie des Systemes Aquatiques (LEESA), UMR 5805-OASU, Universite Bordeaux 1 and CNRS, Place Peyneau, 33120 Arcachon (France)

    2005-09-10

    The aim of this work was to evaluate the potential utility of several biochemical parameters as indicators of the toxic effects of cadmium in the freshwater clam Corbicula fluminea under two levels of oxygenation (normoxia 21 kPa and hypoxia 4 kPa). These variations in oxygenation are representative of the natural environments of bivalves living at the bottom of the water column, where hypoxic episodes may occur regularly. Cadmium accumulation, metallothionein synthesis, MXR protein induction, lipoperoxidation and antioxidant enzyme activities (catalase, glutathione reductase and total and selenium-dependent glutathione peroxidases) were assessed in the gills of C. fluminea in four experimental conditions: normoxia, hypoxia, normoxia with cadmium and hypoxia with cadmium ([Cd] = 30 {mu}g l{sup -1}) over a 14-day period. Behavioural reactions were also followed for the duration of the experiment by monitoring clam activity and valve movements. This study is a first report on biochemical responses under cadmium contamination and hypoxia and will enable us to determine better biomarkers for C. fluminea as they were measured simultaneously. In metal-exposed animals, we found an increasing accumulation of cadmium in the gills with time, and this was more severe in hypoxic conditions. Metallothionein synthesis occurred in contaminated clams and was precocious in hypoxic conditions. MXR protein induction appeared promising due to its quick and significant response to metal with a strong impact from hypoxic contamination. On the other hand, in our experimental conditions, antioxidant parameters did not show decisive responses to contamination and hypoxia, except glutathione peroxidases which decreased systematically with time in a cadmium-independent manner. Lipid peroxidation, expressed as malondialdehyde content, was not stimulated by normoxic contamination, as has been shown in other studies, but was stimulated under hypoxic cadmium contamination. Our study confirms the

  11. Assessment of hyporheic zone, flood-plain, soil-gas, soil, and surface-water contamination at the Old Incinerator Area, Fort Gordon, Georgia, 2009-2010

    Science.gov (United States)

    Guimaraes, Wladmir B.; Falls, W. Fred; Caldwell, Andral W.; Ratliff, W. Hagan; Wellborn, John B.; Landmeyer, James E.

    2011-01-01

    The U.S. Geological Survey, in cooperation with the U.S. Department of the Army Environmental and Natural Resources Management Office of the U.S. Army Signal Center and Fort Gordon, Georgia, assessed the hyporheic zone, flood plain, soil gas, soil, and surface-water for contaminants at the Old Incinerator Area at Fort Gordon, from October 2009 to September 2010. The assessment included the detection of organic contaminants in the hyporheic zone, flood plain, soil gas, and surface water. In addition, the organic contaminant assessment included the analysis of explosives and chemical agents in selected areas. Inorganic contaminants were assessed in soil and surface-water samples. The assessment was conducted to provide environmental contamination data to the U.S. Army at Fort Gordon pursuant to requirements of the Resource Conservation and Recovery Act Part B Hazardous Waste Permit process. Total petroleum hydrocarbons were detected above the method detection level in all 13 samplers deployed in the hyporheic zone and flood plain of an unnamed tributary to Spirit Creek. The combined concentrations of benzene, toluene, ethylbenzene, and total xylene were detected at 3 of the 13 samplers. Other organic compounds detected in one sampler included octane and trichloroethylene. In the passive soil-gas survey, 28 of the 60 samplers detected total petroleum hydrocarbons above the method detection level. Additionally, 11 of the 60 samplers detected the combined masses of benzene, toluene, ethylbenzene, and total xylene above the method detection level. Other compounds detected above the method detection level in the passive soil-gas survey included octane, trimethylbenzene, perchlorethylene, and chloroform. Subsequent to the passive soil-gas survey, six areas determined to have relatively high contaminant mass were selected, and soil-gas samplers were deployed, collected, and analyzed for explosives and chemical agents. No explosives or chemical agents were detected above

  12. Reduction of microbial contamination on the surfaces of layer houses using slightly acidic electrolyzed water.

    Science.gov (United States)

    Ni, L; Cao, W; Zheng, W C; Zhang, Q; Li, B M

    2015-11-01

    The objective of this study was to evaluate the effectiveness of slightly acidic electrolyzed water (SAEW) in reducing pathogens on pure cultures and on cotton fabric surfaces in the presence of organic matter and estimate its efficacy in comparison with povidone iodine solution for reducing pathogenic microorganisms on internal surfaces of layer houses. Pure cultures of E.coli, S.enteritidis, and S.aureus and cotton fabric surfaces inoculated with these strains were treated with SAEW in the presence of bovine serum albumin (BSA). In the absence of BSA, complete inactivation of all strains in pure cultures and on cotton fabric surfaces was observed after 2.5 and 5 min treatment with SAEW at 40 mg/L of available chlorine concentration (ACC), respectively. The bactericidal efficiency of SAEW increased with increasing ACC, but decreased with increasing BSA concentration. Then, the surfaces of the layer houses were sprayed with SAEW at 60, 80, and 100 mg/L of ACC and povidone iodine using the automated disinfection system at a rate of 110 mL/m(2), respectively. Samples from the floor, wall, feed trough, and egg conveyor belt surfaces were collected with sterile cotton swabs before and after spraying disinfection. Compared to tap water, SAEW and povidone iodine significantly reduced microbial populations on each surface of the layer houses. SAEW with 80 or 100 mg/L of ACC showed significantly higher efficacy than povidone iodine for total aerobic bacteria, staphylococci, coliforms, or yeasts and moulds on the floor and feed trough surfaces (P conveyor belt. Results suggest that SAEW exerts a higher or equivalent bactericidal efficiency for the surfaces compared to povidone iodine, and it may be used as an effective alternative for reducing microbial contamination on surfaces in layer houses. © 2015 Poultry Science Association Inc.

  13. Individual, population and community level effects of subtle anthropogenic contamination in estuarine meiobenthos

    Energy Technology Data Exchange (ETDEWEB)

    Rubal, Marcos [CIIMAR/CIMAR-LA - Centro Interdisciplinar de Investigacao Marinha e Ambiental, Universidade do Porto, Laboratorio de Ecotoxicologia, Rua dos Bragas 289, 4050-123 Porto (Portugal); Guilhermino, Lucia M. [CIIMAR/CIMAR-LA - Centro Interdisciplinar de Investigacao Marinha e Ambiental, Universidade do Porto, Laboratorio de Ecotoxicologia, Rua dos Bragas 289, 4050-123 Porto (Portugal); ICBAS - Instituto de Ciencias Biomedicas de Abel Salazar, Departamento de Estudos de Populacoes, Laboratorio de Ecotoxicologia, Universidade do Porto, Lg. Prof. Abel Salazar 2, 4099-003 Porto (Portugal); Medina, Matias H., E-mail: matias.medina@avs-chile.c [AVS Chile SA, Imperial 0655, Off. 3A, Puerto Varas (Chile); Centro i-mar, Universidad de Los Lagos, Camino Chinquihue km 6, Puerto Montt (Chile)

    2009-10-15

    The study presented here searched for the level of taxonomic resolution required to detect the effects of low-level chronic pollution on estuarine meiobenthic communities. Meiofauna from two sites, with special attention to harpacticoid copepods, was analysed at different taxonomic levels of aggregation using uni- and multivariate methods. Adaptation processes that could buffer biodiversity disruptions were also considered through the analysis of fitness-related and tolerance traits in the harpacticoid copepod Paronychocamptus nanus. Results showed that uni- and multivariate analyses could be inadequate when assessing subtle anthropogenic contamination. Instead, the assessment of inter-population differences in tolerance to the main source of stress rises as a required procedure if potential effects of this type of contamination are being investigated. Specifically, a 96 h acute toxicity test performed with populations from the affected site appears as a faster and reliable general tool to assess impacts of low-level chronic pollution in estuaries. - Tolerance of local populations as a reliable tool to assess impacts of subtle anthropogenic contamination in estuaries.

  14. Individual, population and community level effects of subtle anthropogenic contamination in estuarine meiobenthos

    International Nuclear Information System (INIS)

    Rubal, Marcos; Guilhermino, Lucia M.; Medina, Matias H.

    2009-01-01

    The study presented here searched for the level of taxonomic resolution required to detect the effects of low-level chronic pollution on estuarine meiobenthic communities. Meiofauna from two sites, with special attention to harpacticoid copepods, was analysed at different taxonomic levels of aggregation using uni- and multivariate methods. Adaptation processes that could buffer biodiversity disruptions were also considered through the analysis of fitness-related and tolerance traits in the harpacticoid copepod Paronychocamptus nanus. Results showed that uni- and multivariate analyses could be inadequate when assessing subtle anthropogenic contamination. Instead, the assessment of inter-population differences in tolerance to the main source of stress rises as a required procedure if potential effects of this type of contamination are being investigated. Specifically, a 96 h acute toxicity test performed with populations from the affected site appears as a faster and reliable general tool to assess impacts of low-level chronic pollution in estuaries. - Tolerance of local populations as a reliable tool to assess impacts of subtle anthropogenic contamination in estuaries.

  15. The cost and benefit analysis of a contaminated area remediation: case study of dose level selection

    International Nuclear Information System (INIS)

    Lauria, D.C.

    2006-01-01

    In recent years there has been an increasing awareness of the radiological impact of non-nuclear industries that extract and/or process ores and minerals containing naturally occurring radioactive material (NORM). Without radiological rules, these industrial activities may result in significant radioactive contamination of installations and sites. Depending on the potential hazardous to the environment and public health, the radioactive contaminated sites may require remediation. The extent of the site cleanup is a function of the size, localization, complexity, potential risks and on possible future uses envisioned for the site. Since worker and public health, public anxiety and economics factors are involved; the selection of an appropriate dose level can be quite complicated. This paper discusses the selection of a dose level criterion to remedy a site, which was contaminated by wastes from monazite processing. The site is located in the Sao Paulo city; the most densely populated Brazilian City. In its 60,000 square meters of area, a preliminary survey showed contaminated zones covering an area of 6,500 square meters. In some places, contamination was found below the superficial layer of the soil, being the radionuclide vertical distribution not uniform. The 228 Ra soil activity concentration reached values up to 33,000 Bq/kg while those for 226 Ra reached values up to 6,700 Bq/kg. Based on pathway analysis model and considering both the current land use and a hypothetical residential scenario, the residual contamination levels of radionuclides in soil have been derived for dose values of 10 mSv/y (dose level for intervention), 5 mSv/y, 3 mSv/y, 1 mSv/y (dose limit for practices) and 0.3 mSv/y (dose constraint for practices). An optimized value o f annual dose of about 5 mSv/y would be a good option for intervention level, but taking into account the public concern and anxiety, the site location and size, and the remediation costs, it is suggested the

  16. Assessment of PCDD/Fs levels in soil at a contaminated sawmill site in Sweden – A GIS and PCA approach to interpret the contamination pattern and distribution

    International Nuclear Information System (INIS)

    Henriksson, S.; Hagberg, J.; Bäckström, M.; Persson, I.; Lindström, G.

    2013-01-01

    Polychlorinated dibenzo-p-dioxins and polychlorinated dibenzo-p-furans (PCDD/Fs) were analysed in soil from a Swedish sawmill site where chlorophenols (CPs) had been used more than 40 years ago. The most contaminated area at the site was the preservation subarea where the PCDD/F WHO 2005 -TEQ level was 3450 times higher than the current Swedish guideline value of 200 ng TEQ/kg soil for land for industrial use. It was also shown that a fire which destroyed the sawmill might have affected the congener distribution at the concerned areas. To get a broader picture of the contamination both GIS (spatial interpolation analysis) and multivariate data analysis (PCA) were applied to visualize and compare PCDD/F levels as well as congener distributions at different areas at the site. It is shown that GIS and PCA are powerful tools in decisions on future investigations, risk assessments and remediation of contaminated sites. -- Highlights: •GIS and PCA visualize and compare site levels and congener patterns of dioxins. •Subareas were separated by differences in contamination levels and congener patterns. •Fire had a significant effect on the congener distribution at the site. -- The use of geostatistical and multivariate statistical methods are powerful tools to visualize the contamination pattern and distribution at a highly PCDD/Fs-contaminated site

  17. Mercury contamination in vicinity of secondary copper smelters in Fuyang, Zhejiang Province, China: Levels and contamination in topsoils

    International Nuclear Information System (INIS)

    Yin Xuebin; Yao Chunxia; Song Jing; Li Zhibo; Zhang Changbo; Qian Wei; Bi De; Li Chenxi; Teng Ying; Wu Longhua; Wan Hongdong; Luo Yongming

    2009-01-01

    In the present study, we aim to investigate the extent of soil contamination by Hg, particularly by anthropogenic Hg, and tentatively estimate the total Hg (Hg T ) accumulation in topsoils (0-15 cm) in Fuyang, Zhejiang Province-a secondary Cu smelter of China. The results show that the levels of soil Hg in the vicinity of the smelters have been substantially elevated following local smelting activities. The spatial distribution of soil Hg in this area reveals a rapid decrease as the distance from the smelter reaches 1.5 km, which is probably due to the quick deposition process of particulate Hg and reactive gaseous Hg emitted from the smelters. The total accumulation of Hg T in the topsoils of the study area of 10.9 km 2 is approximately 365-561 kg and of which 346-543 kg might be contributed by anthropogenic emission alone with an annual emission of 17.3-27.2 kg Hg to the topsoils. - Secondary copper smelters in Fuyang release a considerable amount of mercury into topsoils.

  18. Application of autonomous robotics to surveillance of waste storage containers for radioactive surface contamination

    International Nuclear Information System (INIS)

    Sweeney, F.J.; Beckerman, M.; Butler, P.L.; Jones, J.P.; Reister, D.B.

    1991-01-01

    This paper describes a proof-of-principal demonstration performed with the HERMIES-III mobile robot to automate the inspection of waste storage drums for radioactive surface contamination and thereby reduce the human burden of operating a robot and worker exposure to potentially hazardous environments. Software and hardware for the demonstration were developed by a team consisting of Oak Ridge National Laboratory, and the Universities of Florida, Michigan, Tennessee, and Texas. Robot navigation, machine vision, manipulator control, parallel processing and human-machine interface techniques developed by the team were demonstrated utilizing advanced computer architectures. The demonstration consists of over 100,000 lines of computer code executing on nine computers

  19. Contamination in surface waters around uranium mines in the Guadiana Basin

    Energy Technology Data Exchange (ETDEWEB)

    Bejarano, J.D.; Tome, F.V.; Sanchez, A.M.; Sanchez, A.R.

    1988-01-01

    In a study of the contamination by uranium mines in the River Guadiana basin, we have found the natural higher concentration of uranium in samples collected near the mines and the expected decrease with distance in samples farther away. In spite of this expected result, there is another interesting fact: a natural isotopic separation is observed. Measurements were by alpha spectrometry with a silicon surface barrier detector. The study was completed with total gamma activity at the same sites as for alphas, using an Nal(Tl) detector. (author).

  20. Comparison of surface contamination monitors for in vivo measurement of 131I in thyroid

    International Nuclear Information System (INIS)

    Oliveira, S.M.; Dantas, A.L.A.; Dantas, B.M.

    2015-01-01

    The routine handling of radiopharmaceuticals in nuclear medicine represents a significant risk of internal exposure to the staff. The IAEA recommends the implementation of monitoring plans for all workers subject to a risk of exposures above 1 mSv per year. However, in Brazil, such recommendation is practically unfeasible due to the lack of a sufficient number of qualified internal dosimetry services over the country. This work presents an alternative based on a simple and inexpensive methodology aimed to perform in-vivo monitoring of 131 I in thyroid using portable surface contamination probes. All models evaluated showed suitable sensitivity for such application. (author)

  1. Bioavailability of caesium-137 from chernozem soils with high and low levels of radioactive contamination

    Science.gov (United States)

    Paramonova, Tatiana; Shamshurina, Eugenia; Machaeva, Ekaterina; Belyaev, Vladimir

    2014-05-01

    Bioavailability of Cs-137 in "soil-plant" system of radioactively contaminated terrestrial ecosystems is the most important factor in the understanding of ecological situation. There are many factors affecting the features of Cs-137 biogeochemical cycle: period since an accident, type and intensity of radioactive fallout, general properties of landscape and the specifics of soil and plant covers, etc. In order to evaluate the importance of soil contamination level for the process of Cs-137 translocation from soil to plant the research in forest-steppe areas of Russia with similar natural properties, but contrasting high (Tula region) and low (Kursk region) levels of radioactive Chernobyl fallout (about 25 years after accident) was conducted. Soil cover of both sites is presented by chernozems with bulk density 1.1-1.2 g/cm3, 6-7% humus and neutral pH 6.5-7.2; plant cover under investigation consist of dry and wet meadows with bioproductivity 1.6-2.5 kg/m2 and 85-90% of biomass concentrated underground, that is typical for Russian forest-steppe landscapes. At the same time levels of soil regional contamination with Cs-137 differ by an order - 620-710 Bq/kg (210-250 kBq/m2) in Tula region and 30-55 Bq/kg (10-20 kBq/m2) in Kursk region. At a higher level of soil radioactive contamination specific activity of Cs-137 in vegetation of meadows is noticeably increased (103-160 Bq/kg in Tula region versus 12-14 Bq/kg in Kursk region) with correlation coefficient r 0.87. Increasing of Cs-137 in the underground parts of plants plays a decisive role in this process, while the specific radionuclide's activity in the aboveground parts of different sites is almost invariant (and ubiquitously roots contain 2-5 times more Cs-137 than shoots). The values of transfer factors for Cs-137 (the ratio of the specific Cs-137 activities in the plant tissue and in the soil) at various levels of soil radioactive contamination vary within a relatively narrow range 0.1-0.4, that confirms the

  2. Sampling for Beryllium Surface Contamination using Wet, Dry and Alcohol Wipe Sampling

    Energy Technology Data Exchange (ETDEWEB)

    Kerr, Kent [Central Missouri State Univ., Warrensburg, MO (United States)

    2004-12-01

    This research project was conducted at the National Nuclear Security Administration's Kansas City Plant, operated by Honeywell Federal Manufacturing and Technologies, in conjunction with the Safety Sciences Department of Central Missouri State University, to compare relative removal efficiencies of three wipe sampling techniques currently used at Department of Energy facilities. Efficiencies of removal of beryllium contamination from typical painted surfaces were tested by wipe sampling with dry Whatman 42 filter paper, with water-moistened (Ghost Wipe) materials, and by methanol-moistened wipes. Test plates were prepared using 100 mm X 15 mm Pyrex Petri dishes with interior surfaces spray painted with a bond coat primer. To achieve uniform deposition over the test plate surface, 10 ml aliquots of solution containing 1 beryllium and 0.1 ml of metal working fluid were transferred to the test plates and subsequently evaporated. Metal working fluid was added to simulate the slight oiliness common on surfaces in metal working shops where fugitive oil mist accumulates over time. Sixteen test plates for each wipe method (dry, water, and methanol) were processed and sampled using a modification of wiping patterns recommended by OSHA Method 125G. Laboratory and statistical analysis showed that methanol-moistened wipe sampling removed significantly more (about twice as much) beryllium/oil-film surface contamination as water-moistened wipes (p< 0.001), which removed significantly more (about twice as much) residue as dry wipes (p <0.001). Evidence for beryllium sensitization via skin exposure argues in favor of wipe sampling with wetting agents that provide enhanced residue removal efficiency.

  3. A model to determine the radiological implications of non-fixed radioactive contamination on the surfaces of packages and conveyances

    International Nuclear Information System (INIS)

    Hughes, J.S.; Warner Jones, S.M.; Lizot, M.T.; Perrin, M.L.; Thierfeld, S.; Schroedl, E.; Schwarz, G.; Rawl, R.; Munakata, M.; Hirose, M.

    2004-01-01

    The surfaces of packages and conveyances used to transport radioactive materials can sometimes become contaminated with radioactive material. This usually occurs as a result of the transfer of radioactive material from areas in which these packages and conveyances are handled. This contamination may subsequently be transferred to transport equipment, workers and to areas accessible to the public. This can represent a significant radiation safety issue that requires careful management. The current regulatory limits for non-fixed contamination on packages and conveyances have been in use for over 40 years, and are based on a simple exposure model. However, the bases on which these limits were derived have been subject to changes, as a result of successive revisions of international recommendations. In recognition of this need for a review and analysis of the current contamination limits an IAEA Co-ordinated Research Project (CRP) on the ''Radiological Aspects of Package and Conveyance Non-Fixed Contamination'' was initiated to review the scientific basis for the current regulatory limits for surface contamination. The CRP was also to develop guidance material for evaluating the radiological significance of surface contamination to workers and the public in light of state-of-the-art research, technical developments and current transport practices. The specific objectives of the work undertaken within this multi-national CRP were, in accordance with the terms of reference: To ensure that appropriate models exist for all package types including consideration of the aspects pertinent for assessing and revising a surface contamination model for transport. To collect - where possible - contamination, operational and dosimetric data to ensure modelling consistency. To use models for assessing the limitations and optimisation of radiation doses incurred in transport operations, and to consider preventive methods for package and conveyance contamination

  4. Nickel, Lead and Zinc Contamination in the Surface Sediments of Agh Gel Wetland, Iran

    Directory of Open Access Journals (Sweden)

    Soheil Sobhan Ardakani

    2016-07-01

    Full Text Available Background & Aims of the Study: Due to the increased human activities around the Agh Gel wetland, this study aimed to measured accumulations of heavy metals (Ni, Pb and Zn in the surface sediment samples taken from this wetland. Materials & Methods: Samples were taken from 10 stations and exposed to bulk digestion and chemical partitioning. Finally, Ni, Pb and Zn concentrations were monitored with ICP-OES in the sediments. Also, geo-accumulation index, contamination factor and pollution load index were used to evaluate the magnitude of contaminants in the sediment profile. Results: The results showed, the average of metal concentration in samples (mg kg-1 wet weight were 34.20±3.58 for Ni, 25.37±2.52 for Pb and 127.20±15.21 for Zn, respectively. Therefore, the pattern of metal concentrations in sediment was determined as Zinc>Nickel >Lead. According to the mean I-geo values, sediments' qualities are classified as unpolluted category for Ni and Pb. Also, sediment's quality is classified as unpolluted to moderately polluted for Zn. The CF values for all elements are classified as moderate contamination. The PLI values indicated that metal pollution exists for all sampling stations. Conclusions: The obtained results indicated that the Agh Gel wetland has a potential to threaten by chemical pollutants such as agricultural effluent. So, in order to preserve the environment of the Agh Gel wetland from deterioration, monitoring of water and sediment qualities is recommended periodically.

  5. Assessment of heavy metal contamination, levels in topsoil at selected auto-workshops in Accra, Ghana

    International Nuclear Information System (INIS)

    Ziblim, M. Y.

    2015-07-01

    The research was conducted to assess the levels of contamination of heavy metals in the topsoil at selected auto-workshops in Accra to determine the anthropogenic and crustal contributions and the human heath risk associated with them. Soil samples collected from four auto-workshops were analysed using Atomic Absorption Spectrometer. Eleven (11) elements: Co, Fe, Cu, Mn, Cr, As, Hg, Zn, Pb, Ni, and Cd were identified in each sample collected from the auto-workshops. Pollution indices; contamintion factor (Cf) index of geoaccumulation (Igeo) and pollution load index (PLI) were used to assess the contamination levels. It revealed the extent of contamination at the auto-workshops for most of the elements which range from low to considerate contamintion. Lead (Pb) recorded the greatest contamination levels at the auto-electrical location. The results from the index of geoccumulation showed no pollution to highly pollution indicting high variations of pollution levels at different locations. The results of the PLI in almost all locations ranged from moderately to extremely polluted. Noncancer effect on children and adults due to exposure to the topsoil were also estimated with some selected metal elements. The hazard quotient (HQ) evaluation, showed ingestion to be the route of exposure to soil dust that results in a higher risk for heavy metals, followed by dermal contact. The effect due to inhalation of resuspended dust particles through the mouth and nose is relatively low. It was observed that, the auto-workshops are generally polluted with heavy metals and therefore posing ill-health effect to the humans and the environment. (au)

  6. Acceptable contamination levels in solar grade silicon: From feedstock to solar cell

    International Nuclear Information System (INIS)

    Hofstetter, J.; Lelievre, J.F.; Canizo, C.; Luque, A. del

    2009-01-01

    Ultimately, alternative ways of silicon purification for photovoltaic applications are developed and applied. There is an ongoing debate about what are the acceptable contamination levels within the purified silicon feedstock to specify the material as solar grade silicon. Applying a simple model and making some additional assumptions, we calculate the acceptable contamination levels of different characteristic impurities for each fabrication step of a typical industrial mc-Si solar cell. The acceptable impurity concentrations within the finished solar cell are calculated for SRH recombination exclusively and under low injection conditions. It is assumed that during solar cell fabrication impurity concentrations are only altered by a gettering step. During the crystallization process, impurity segregation at the solid-liquid interface and at extended defects are taken into account. Finally, the initial contamination levels allowed within the feedstock are deduced. The acceptable concentration of iron in the finished solar cell is determined to be 9.7x10 -3 ppma whereas the concentration in the silicon feedstock can be as high as 12.5 ppma. In comparison, the titanium concentration admitted in the solar cell is calculated to be 2.7x10 -4 ppma and the allowed concentration of 2.2x10 -2 ppma in the feedstock is only two orders of magnitude higher. Finally, it is shown theoretically and experimentally that slow cooling rates can lead to a decrease of the interstitial Fe concentration and thus relax the purity requirements in the feedstock.

  7. Phytoextraction for clean-up of low-level uranium contaminated soil evaluated

    Energy Technology Data Exchange (ETDEWEB)

    Vandenhove, H. E-mail: hvandenh@sckcen.be; Hees, M. van

    2004-07-01

    Spills in the nuclear fuel cycle have led to soil contamination with uranium. In case of small contamination just above release levels, low-cost yet sufficiently efficient remedial measures are recommended. This study was executed to test if low-level U contaminated sandy soil from a nuclear fuel processing site could be phytoextracted in order to attain the required release limits. Two soils were tested: a control soil (317 Bq {sup 238}U kg{sup -1}) and the same soil washed with bicarbonate (69 Bq {sup 238}U kg{sup -1}). Ryegrass (Lolium perenne cv. Melvina) and Indian mustard (Brassica juncea cv. Vitasso) were used as test plants. The annual removal of soil activity by the biomass was less than 0.1%. The addition of citric acid (25 mmol kg{sup -1}) 1 week before the harvest increased U uptake up to 500-fold. With a ryegrass and mustard yield of 15,000 and 10,000 kg ha{sup -1}, respectively, up to 3.5% and 4.6% of the soil activity could be removed annually by the biomass. With a desired activity reduction level of 1.5 and 5 for the bicarbonate-washed and control soil, respectively, it would take 10-50 years to attain the release limit. However, citric acid addition resulted in a decreased dry weight production.

  8. Building classification trees to explain the radioactive contamination levels of the plants

    International Nuclear Information System (INIS)

    Briand, B.

    2008-04-01

    The objective of this thesis is the development of a method allowing the identification of factors leading to various radioactive contamination levels of the plants. The methodology suggested is based on the use of a radioecological transfer model of the radionuclides through the environment (A.S.T.R.A.L. computer code) and a classification-tree method. Particularly, to avoid the instability problems of classification trees and to preserve the tree structure, a node level stabilizing technique is used. Empirical comparisons are carried out between classification trees built by this method (called R.E.N. method) and those obtained by the C.A.R.T. method. A similarity measure is defined to compare the structure of two classification trees. This measure is used to study the stabilizing performance of the R.E.N. method. The methodology suggested is applied to a simplified contamination scenario. By the results obtained, we can identify the main variables responsible of the various radioactive contamination levels of four leafy-vegetables (lettuce, cabbage, spinach and leek). Some extracted rules from these classification trees can be usable in a post-accidental context. (author)

  9. Thallium dispersal and contamination in surface sediments from South China and its source identification.

    Science.gov (United States)

    Liu, Juan; Wang, Jin; Chen, Yongheng; Shen, Chuan-Chou; Jiang, Xiuyang; Xie, Xiaofan; Chen, Diyun; Lippold, Holger; Wang, Chunlin

    2016-06-01

    Thallium (Tl) is a non-essential element in humans and it is considered to be highly toxic. In this study, the contents, sources, and dispersal of Tl were investigated in surface sediments from a riverine system (the western Pearl River Basin, China), whose catchment has been contaminated by mining and roasting of Tl-bearing pyrite ores. The isotopic composition of Pb and total contents of Tl and other relevant metals (Pb, Zn, Cd, Co, and Ni) were measured in the pyrite ores, mining and roasting wastes, and the river sediments. Widespread contamination of Tl was observed in the sediments across the river, with the highest concentration of Tl (17.3 mg/kg) measured 4 km downstream from the pyrite industrial site. Application of a modified Institute for Reference Materials and Measurement (IRMM) sequential extraction scheme in representative sediments unveiled that 60-90% of Tl and Pb were present in the residual fraction of the sediments. The sediments contained generally lower (206)Pb/(207)Pb and higher (208)Pb/(206)Pb ratios compared with the natural Pb isotope signature (1.2008 and 2.0766 for (206)Pb/(207)Pb and (208)Pb/(206)Pb, respectively). These results suggested that a significant fraction of non-indigenous Pb could be attributed to the mining and roasting activities of pyrite ores, with low (206)Pb/(207)Pb (1.1539) and high (208)Pb/(206)Pb (2.1263). Results also showed that approximately 6-88% of Tl contamination in the sediments originated from the pyrite mining and roasting activities. This study highlights that Pb isotopic compositions could be used for quantitatively fingerprinting the sources of Tl contamination in sediments. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Use of a fractal-like gold nanostructure in surface-enhanced raman spectroscopy for detection of selected food contaminants.

    Science.gov (United States)

    He, Lili; Kim, Nam-Jung; Li, Hao; Hu, Zhiqiang; Lin, Mengshi

    2008-11-12

    The safety of imported seafood products because of the contamination of prohibited substances, including crystal violet (CV) and malachite green (MG), raised a great deal of concern in the United States. In this study, a fractal-like gold nanostructure was developed through a self-assembly process and the feasibility of using surface-enhanced Raman spectroscopy (SERS) coupled with this nanostructure for detection of CV, MG, and their mixture (1:1) was explored. SERS was capable of characterizing and differentiating CV, MG, and their mixture on fractal-like gold nanostructures quickly and accurately. The enhancement factor of the gold nanostructures could reach an impressive level of approximately 4 x 10(7), and the lowest detectable concentration for the dye molecules was at approximately 0.2 ppb level. These results indicate that SERS coupled with fractal-like gold nanostructures holds a great potential as a rapid and ultra-sensitive method for detecting trace amounts of prohibited substances in contaminated food samples.

  11. Atmospheric contamination

    International Nuclear Information System (INIS)

    Gruetter, Juerg

    1997-01-01

    It is about the levels of contamination in center America, the population's perception on the problem, effects of the atmospheric contamination, effects in the environment, causes of the atmospheric contamination, possibilities to reduce the atmospheric contamination and list of Roeco Swisscontac in atmospheric contamination

  12. [Cleaning efficacy of different solvents on sealer-contaminated dentin surface].

    Science.gov (United States)

    Zang, H L; Wang, Y; Liang, Y H

    2018-02-18

    To evaluate the influence of an epoxy resin-based sealer on the bond strength of adhesive resins to dentin and the cleaning efficacy of different solvents in removing sealer residues. The occlusal enamel of 25 freshly extracted human third molars without caries were removed to expose flat surfaces of dentin. The teeth were randomly divided into five groups according to the treatment received: For negative control group, the dentin surfaces were not contaminated with AH-Plus; For the other 4 experimental groups, the samples were contaminated with AH-Plus for 5 min and different measures were taken: For positive control group, the sealer were wiped with dry cotton pellets; For solvents experimental groups: cotton pellets saturated with 95% (volume fraction) ethanol, 99.5% (volume fraction) acetone or 99% (volume fraction) amyl acetate were used to wipe the sealer until the surface appeared clean when viewed through a stereomicroscope under ×10 magnification, then rinsed with de-ionized water for 3 s. After sealer removal, a self-etching adhesive system was applied on the surfaces with resin composite. The samples were sectioned into 1.0 mm×1.0 mm stick specimens (n=45) for microtensile test. Failure modes at the dentin-resin interface were observed using a stereomicroscope. The samples were sectioned into 1.0 mm piece specimens (n=4) for scanning electron microscope observation. The microtensile bond strength data were analyzed by one-way ANOVA. Chi-square test were used to analyse the failure modes between the groups. There was significant difference among the five groups (Pamyl acetate group and negative control group (P>0.05). The bond strength of acetone group and amyl acetate group were (45.94±10.37) MPa and (43.99±7.01) MPa, respectively. The ethanol group exhibited lower bond strength than that of acetone group and amyl acetate group (Pamyl acetate group were as dense and uniform as in negative control group. The distribution of failure modes showed no

  13. HTO transfer from contaminated surfaces to the atmosphere: a database for model validation

    International Nuclear Information System (INIS)

    Davis, P.A.; Amiro, B.D.; Workman, W.J.G.; Corbett, B.J.

    1996-12-01

    This report comprises a detailed database that can be used to validate models of the emission of tritiated water vapour (HTO) from natural contaminated surfaces to the atmosphere. The data were collected in 1992 July during an intensive field study based on the flux-gradient method of micrometeorology. The measurements were made over a wetland area at the Chalk River Laboratories, and over a grassed field near the Pickering Nuclear Generating Station. The study sites, the sampling protocols and the analytical techniques are described in detail, and the measured fluxes are presented. The report also contains a detailed listing of HTO concentrations in air at two heights, HTO concentrations in the source compartments (soil, surface water and vegetation), supporting meteorological data, and various vegetation and soil properties. The uncertainties in all of the measured data are estimated. (author). 15 refs., 23 tabs., 9 figs

  14. Heavy metal contamination in surface sediments of Yangtze River intertidal zone: An assessment from different indexes

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Weiguo [State Key Laboratory of Estuarine and Coastal Research, East China Normal University, Shanghai 200062 (China); Feng Huan, E-mail: fengh@mail.montclair.ed [Department of Earth and Environmental Studies, Montclair State University, 1 Normal Avenue, Montclair, NJ 07043 (United States); Chang Jinna; Qu Jianguo; Xie Hongxia; Yu Lizhong [State Key Laboratory of Estuarine and Coastal Research, East China Normal University, Shanghai 200062 (China)

    2009-05-15

    Surface sediments (0-5 cm) from 59 stations within the Yangtze River intertidal zone (YRIZ) were sampled for metal contamination analysis in April and August 2005. The concentrations ranged (in mg kg{sup -1} dry weight): Al, 40,803-97,213; Fe, 20,538-49,627; Cd, 0.12-0.75; Cr, 36.9-173; Cu, 6.87-49.7; Mn, 413-1,112; Ni, 17.6-48.0; Pb, 18.3-44.1; and Zn, 47.6-154; respectively. Among the 59 sampling stations, enrichment factors (EF) indicate enrichment of Cd (52 stations), Cr (54 stations), Cu (5 stations), Ni (26 stations), Pb (5 stations) and Zn (5 stations). Geoaccumulation indexes (I{sub geo}) also suggest individual metal contamination in localized areas. This study indicates that Cd, Cr and Ni enrichment in the YRIZ sediment is widespread whereas Cu, Mn, Pb and Zn enrichment is localized or nonexistent. Factor and cluster analyses indicate that Cd is associated with total organic carbon whereas Cu, Cr, Ni, Pb and Zn have a close association with Mn. - Surface sediment metal enrichment is evidenced for Cd, Cr and Ni in the Yangtze River intertidal zone.

  15. Genes involved in arsenic transformation and resistance associated with different levels of arsenic-contaminated soils

    Directory of Open Access Journals (Sweden)

    Wang Gejiao

    2009-01-01

    Full Text Available Abstract Background Arsenic is known as a toxic metalloid, which primarily exists in inorganic form [As(III and As(V] and can be transformed by microbial redox processes in the natural environment. As(III is much more toxic and mobile than As(V, hence microbial arsenic redox transformation has a major impact on arsenic toxicity and mobility which can greatly influence the human health. Our main purpose was to investigate the distribution and diversity of microbial arsenite-resistant species in three different arsenic-contaminated soils, and further study the As(III resistance levels and related functional genes of these species. Results A total of 58 arsenite-resistant bacteria were identified from soils with three different arsenic-contaminated levels. Highly arsenite-resistant bacteria (MIC > 20 mM were only isolated from the highly arsenic-contaminated site and belonged to Acinetobacter, Agrobacterium, Arthrobacter, Comamonas, Rhodococcus, Stenotrophomonas and Pseudomonas. Five arsenite-oxidizing bacteria that belonged to Achromobacter, Agrobacterium and Pseudomonas were identified and displayed a higher average arsenite resistance level than the non-arsenite oxidizers. 5 aoxB genes encoding arsenite oxidase and 51 arsenite transporter genes [18 arsB, 12 ACR3(1 and 21 ACR3(2] were successfully amplified from these strains using PCR with degenerate primers. The aoxB genes were specific for the arsenite-oxidizing bacteria. Strains containing both an arsenite oxidase gene (aoxB and an arsenite transporter gene (ACR3 or arsB displayed a higher average arsenite resistance level than those possessing an arsenite transporter gene only. Horizontal transfer of ACR3(2 and arsB appeared to have occurred in strains that were primarily isolated from the highly arsenic-contaminated soil. Conclusion Soils with long-term arsenic contamination may result in the evolution of highly diverse arsenite-resistant bacteria and such diversity was probably caused in

  16. Levels of chemical contaminants in nonoccupationally exposed U.S. residents

    International Nuclear Information System (INIS)

    Holleman, J.W.; Hammons, A.S.

    1978-08-01

    Data are presented on the levels of all chemical contaminants resulting from environmental pollution which have been found in human tissues including blood, urine, breast milk, and tissue samples obtained at autopsy. Most data results from specific surveys to determine health hazards. The roles of trace elements and recognition of the need to determine baseline levels of chemicals introduced into the environment are factors which have motivated surveys by individual investigators. Thus, most data on chemicals in human tissues record levels of pesticides (e.g., DDT and metabolites), levels of trace metals such as lead, cadmium, and mercury, or levels of nutritionally essential elements such as zinc, copper, manganese, and fluoride. Data available on iron and calcium are not presented as their presence in the environment is generally not considered hazardous. Data on several uncommon chemicals, such as indium and ytterbium, are included basically as items of interest and to further document their presence in healthy individuals. Baseline data were presented where available to provide perspective as to chemical levels which might be expected under conditions where exposure could be considered normal or not directly related to a pollutant source. Nearly 600 cited surveys or investigations, most of which were reported within the past decade, are listed. Ninety-four different chemical contaminants, primarily trace metals and organochlorine pesticides, are reported. It is estimated that over 75% of the data published during the past 30 years on chemical contaminants derived from environmental pollution and found in human tissue in the United States are represented in this report

  17. A comparison of the surface contaminants of handwritten recycled and printed electronic parenteral nutrition prescriptions and their transfer to bag surfaces during delivery to hospital wards.

    Science.gov (United States)

    Austin, Peter David; Hand, Kieran Sean; Elia, Marinos

    2014-02-01

    Handwritten recycled paper prescription for parenteral nutrition (PN) may become a concentrated source of viable contaminants, including pathogens. This study examined the effect of using fresh printouts of electronic prescriptions on these contaminants. Cellulose sponge stick swabs with neutralizing buffer were used to sample the surfaces of PN prescriptions (n = 32 handwritten recycled; n = 32 printed electronic) on arrival to the pharmacy or following printing and PN prescriptions and bags packaged together during delivery (n = 38 handwritten recycled; n = 34 printed electronic) on arrival to hospital wards. Different media plates and standard microbiological procedures identified the type and number of contaminants. Staphylococcus aureus, fungi, and mold were infrequent contaminants. nonspecific aerobes more frequently contaminated handwritten recycled than printed electronic prescriptions (into pharmacy, 94% vs 44%, fisher exact test P .001; onto wards, 76% vs 50%, p = .028), with greater numbers of colony-forming units (CFU) (into pharmacy, median 130 [interquartile range (IQR), 65260] VS 0 [075], Mann-Whitney U test, P .001; onto wards, median 120 [15320] vs 10 [040], P = .001). packaging with handwritten recycled prescriptions led to more frequent nonspecific aerobic bag surface contamination (63% vs 41%, fisher exact test P = .097), with greater numbers of CFU (median 40 [IQR, 080] VS 0 [040], Mann-Whitney U test, P = .036). The use of printed electronic PN prescriptions can reduce microbial loads for contamination of surfaces that compromises aseptic techniques.

  18. Evaluation of otoscope cone disinfection techniques and contamination level in small animal private practice.

    Science.gov (United States)

    Kirby, Allison L; Rosenkrantz, Wayne S; Ghubash, Rudayna M; Neradilek, Blazej; Polissar, Nayak L

    2010-04-01

    The objective of this study was to evaluate the level of bacterial contamination of otoscope cones in veterinary private practice, and to determine the most effective method of disinfection. Fifty small animal practices participated in this study, which included a detailed survey regarding otoscope cleaning, storage and usage and quantitative culture of the cleaned and stored otoscope cones. Using sterile technique, two cones from each of the 50 hospitals were swabbed and submitted for quantitative culture. Contamination was present in 29% of the samples and the following organisms were isolated: Flavobacterium brevis (10%), Pseudomonas aeruginosa (6%), Pseudomonas alcaligenes (4%), Staphylococcus intermedius (4%), Corynebacterium spp. (2%), Bacillus spp. (1%), Enterococcus faecalis (1%) Malassezia spp. (1%). There was no statistically significant difference between storage type (dry versus stored in solution) and for the instrumentation used to clean the cones (brush, cotton-tipped applicator, both versus none). There was a statistically significant difference between the different cleaning solutions (P < 0.001) and between the storage solutions (P = 0.003). A single most effective cleaning solution was unable to be determined due to the large number of solutions utilized. Cetylcide G (Cetylite Industries, Inc., Pennsauken, NJ, USA) was the most effective of the three most commonly used storage solutions (Cetylcide G, Benz-all, and 2% Chlorhexidine gluconate) when used as directed (P < 0.001). The level of contamination had a positive association with the frequency of cone use and a negative association with the frequency of storage solution replacement.

  19. Grounding a natural background level for fluoride in a potentially contaminated crystalline aquifer in south India.

    Science.gov (United States)

    Sajil Kumar, P J

    2017-12-01

    Fluoride contamination is one of the most alarming issues for those countries that depend on groundwater drinking water supply. A careful examination of the hydrogeochemical conditions and routine monitoring of fluoride level are therefore quintessential. Estimation of natural background level (NBL) of fluoride becomes significant information for assessing the current and future contamination episodes. Vellore District in Tamil Nadu is a hard rock terrain known for its F-rich groundwater. In this study, we attempted to form a benchmark for fluoride using hydrochemical pre-selection (based on TDS and NO 3 ) and cumulative probability plots (CPP). Principle components analysis is (PCA) applied to evaluate the corresponding factor grouping of the total of 68 samples, which is later mapped using geostatistical tool in ArcGIS. From the CPP, we derived the NBL of F as 0.75 mg/L. This value is compared with the observed concentration in each sample and they were spatially plotted based on the NBL. Resultant plot suggests that W-NW part of the study area has exceeded and E-EW regions are below the NBL of F. Spatial variation of the factor scores also supported this observation. Grounding an NBL and extending it to other parts of the potential contaminated aquifers are highly recommended for better understanding and management of the water supply systems.

  20. Multi-scale levels of Cs-137 contamination of landscapes of the Bryansk Region (with reference to results of air gamma survey)

    Science.gov (United States)

    Linnik, Vitaly; Sokolov, Alexander; Sokolov, Peter

    2017-04-01

    As a result of the Chernobyl accident on April 26, 1986, large amounts of radionuclides were released into the atmosphere, resulting in high contamination in Belarus, Ukraine, and Russia. High variability of environmental parameters and multi-scale nature of initial fallout significantly contributed to very complicated Cs-137 patterns. The first maps of radioactive contamination due to the accident at the Chernobyl nuclear power plant, built in May 1986, already identified a heterogeneous nature of the contamination zones [1]. A complex combination of factors, such as the nature of the deposition (dry, wet), various volumetric activity of radionuclides in the atmosphere during the deposition of aerosols on the earth's surface, led to the formation of multiscale fields of radionuclide contamination, where each scale correlates with "pollution spots" having their own specific nature]. Air gamma survey was conducted with a grid 100x100 m and it allowed to reveal different levels of scale "spots" of Cs-137 contamination associated with the movement of polluted air and the influence of the underlying surface - forests, river valleys. Cs-137 contamination field has an extraordinary feature - uniqueness of its spatial structure in different districts of the Bryansk region. A maximal area of "cesium" spots up to 30-50 km in size and with a contamination density of more than 1000 kBq/m2 is observed in the western part of the Bryansk Region. Their spatial structure is extremely heterogeneous, the differences in the local density of Cs-137 contamination being due to those in intensity of precipitation (wet deposition). The central part of the Bryansk Region with the density of contamination below 37 kBq/m2 (up to 3-5 kBq/m2 ) is an example of a condensing zone of "dry" deposition. With a larger scale, allowing individual elements of Cs-137 contamination to be shown in a more distinct way, it is possible to observe the relationship of contamination with a number of landscape

  1. An Assessment of Heavy Metal Contamination on the Surface Sediment of Seagrass Beds at the Khanh Hoa Coast, Vietnam.

    Science.gov (United States)

    Nguyen, Xuan-Vy; Tran, Minh-Hue; Le, Trong-Dung; Papenbrock, Jutta

    2017-12-01

    Seagrasses beds are vulnerable ecosystems. Human-induced disturbances, including heavy metal pollution, cause losses in seagrass beds. Assessment of the heavy metal concentration in seagrass meadows is an urgent need in order to protect and sustain these ecosystems. The concentration of eight trace metals in the surface sediment was observed from six seagrass beds at Khanh Hoa's coast, Vietnam. Three pollution indices and statistical analysis were used to evaluate the levels of contamination with these elements. This report on heavy metals within seagrass beds in Vietnam shows that, based on enrichment factors, only one location revealed moderately severe enrichment of Cu. Geo-accumulation indices fall in the uncontaminated class at all locations whereas for the ecological risk factor, values of Cu at My Giang and of Pb at Thuy Trieu were in a moderate risk class. Hence, two of eight locations may be exposed to high Cu and Pb.

  2. Solutal Marangoni flows of miscible liquids drive transport without surface contamination

    Science.gov (United States)

    Kim, Hyoungsoo; Muller, Koen; Shardt, Orest; Afkhami, Shahriar; Stone, Howard A.

    2017-11-01

    Mixing and spreading of different liquids are omnipresent in nature, life and technology, such as oil pollution on the sea, estuaries, food processing, cosmetic and beverage industries, lab-on-a-chip devices, and polymer processing. However, the mixing and spreading mechanisms for miscible liquids remain poorly characterized. Here, we show that a fully soluble liquid drop deposited on a liquid surface remains as a static lens without immediately spreading and mixing, and simultaneously a Marangoni-driven convective flow is generated, which are counterintuitive results when two liquids have different surface tensions. To understand the dynamics, we develop a theoretical model to predict the finite spreading time and length scales, the Marangoni-driven convection flow speed, and the finite timescale to establish the quasi-steady state for the Marangoni flow. The fundamental understanding of this solutal Marangoni flow may enable driving bulk flows and constructing an effective drug delivery and surface cleaning approach without causing surface contamination by immiscible chemical species.

  3. A biogeochemical transport model to simulate the attenuation of chlorinated hydrocarbon contaminant fluxes across the groundwater-surface water interface

    DEFF Research Database (Denmark)

    Malaguerra, Flavio; Binning, Philip John; Albrechtsen, Hans-Jørgen

    2009-01-01

    Chlorinated hydrocarbons originating from point sources are amongst the most prevalent contaminants of ground water and surface water resources. Riparian zones may play an important role in the attenuation of contaminant concentrations when contaminant plumes flow from groundwater to surface water...... because of the occurrence of redox gradients, strongly reductive conditions and high biological activity. In order to meet the expectations of the EU Water Framework Directive, an evaluation of the impact of such plumes on surface water is needed. The aim of this work is to develop a groundwater transport...... number of geochemical processes, allows the simulation of soil geochemical transformations when microbial by-products are released to surface water, and the consideration of non-linear feedbacks on bacterial growth and pollutant transformations. Sensitivity analysis is performed through Monte Carlo...

  4. Microbial contaminants isolated from items and work surfaces in the post- operative ward at Kawolo general hospital, Uganda.

    Science.gov (United States)

    Sserwadda, Ivan; Lukenge, Mathew; Mwambi, Bashir; Mboowa, Gerald; Walusimbi, Apollo; Segujja, Farouk

    2018-02-06

    Nosocomial infections are a major setback in the healthcare delivery system especially in developing countries due to the limited resources. The roles played by medical care equipment and work surfaces in the transmission of such organisms have inevitably contributed to the elevated mortality, morbidity and antibiotic resistances. A total 138 samples were collected during the study from Kawolo general hospital. Swab samples were collected from various work surfaces and fomites which consisted of; beds, sink taps, infusion stands, switches, work tables and scissors. Cultures were done and the susceptibility patterns of the isolates were determined using Kirby Bauer disc diffusion method. Data was analyzed using Stata 13 and Microsoft Excel 2013 packages. A total of 44.2% (61/138) of the collected swab specimens represented the overall bacterial contamination of the sampled articles. Staphylococcus aureus and Klebsiella pneumoniae accounted for the highest bacterial contaminants constituting of 75.4% (46/61) and 11.5% (7/61) respectively. Infusion stands and patient beds were found to have the highest bacterial contamination levels both constituting 19.67% (12/61). The highest degree of transmission of organisms to patients was found to be statistically significant for patient beds with OR: 20.1 and P-value 8X10 - 4 . Vancomycin, ceftriaxone and ciprofloxacin were the most effective antibiotics with 100%, 80% and 80% sensitivity patterns among the isolates respectively. Multi-drug resistant (MDR) Staphylococcus aureus accounted for 52% (24/46) with 4% (1/24) classified as a possible extensively drug resistant (XDR) whereas Gram negative isolates had 27% (4/15) MDR strains out of which 50%(2/4) were classified as possible pan-drug resistant (PDR). The high prevalence of bacterial contaminants in the hospital work environment is an indicator of poor or ineffective decontamination. The study findings reiterate the necessity to formulate drug usage policies and re

  5. Beta Autoradiography. An analytical technique to investigate radionuclides contamination on surface

    International Nuclear Information System (INIS)

    Ficher, P.; Goutelard, F.; Siitari-Kauppi, M.

    2012-01-01

    In decommissioning of old buildings and after disposal of nuclear facilities (materials, glove boxes,...), the inventory of the radioactive contamination of various building materials needs to be obtained in order to fix the working condition for dismantling. The challenge of this study was to classify different building materials of a whole research laboratory that was dedicated to research on organic molecules labeled with H-3 and C-14. The problem of waste classification is essential for safety treatment of waste and also for its cost. The analytical technique of beta autoradiography particularly well known for biological researches has been tested to investigate radionuclides contamination on surface. This technique is mainly interesting for beta and alpha emitters but also sensitive to gamma radiation. The first step of this technique is the deposit of a film on the surface of material to be analyzed. Films can be deposited on the ground or also fixed on the walls or even on the ceiling. The film is a plastic sheet covered with an emulsion containing photostimulable crystals and Eu that is activated when the film is exposed on radioactive source. The exposed films are then scanned with the Cyclone Plus equipment to get a digitized image. This image represents the radioactivity of the surface studied. The possibility to re-use the films is very important to investigate a large area. This autoradiography technique has retained our attention for its sensitivity and moreover the possibility of 2-dimensional investigation has been found as a real advantage. However it remains now as a qualitative technique and new studies must be launched to prove its quantitative potentialities. The high spatial resolution was not as important as in biological observation, and the mm resolution is totally sufficient

  6. Final report: survey and removal of radioactive surface contamination at environmental restoration sites, Sandia National Laboratories/New Mexico. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, K.A.; Mitchell, M.M. [Brown and Root Environmental, Albuquerque, NM (United States); Jean, D. [MDM/Lamb, Inc., Albuquerque, NM (United States); Brown, C. [Environmental Dimensions, Inc., Albuquerque, NM 87109 (United States); Byrd, C.S. [Sandia National Labs., Albuquerque, NM (United States)

    1997-09-01

    This report describes the survey and removal of radioactive surface contamination at Sandia`s Environmental Restoration (ER) sites. Radiological characterization was performed as a prerequisite to beginning the Resource Conservation and Recovery Act (RCRA) corrective action process. The removal of radioactive surface contamination was performed in order to reduce potential impacts to human health and the environment. The predominant radiological contaminant of concern was depleted uranium (DU). Between October 1993 and November 1996 scanning surface radiation surveys, using gamma scintillometers, were conducted at 65 sites covering approximately 908 acres. A total of 9,518 radiation anomalies were detected at 38 sites. Cleanup activities were conducted between October 1994 and November 1996. A total of 9,122 anomalies were removed and 2,072 waste drums were generated. The majority of anomalies not removed were associated with a site that has subsurface contamination beyond the scope of this project. Verification soil samples (1,008 total samples) were collected from anomalies during cleanup activities and confirm that the soil concentration achieved in the field were far below the target cleanup level of 230 pCi/g of U-238 (the primary constituent of DU) in the soil. Cleanup was completed at 21 sites and no further radiological action is required. Seventeen sites were not completed since cleanup activities wee precluded by ongoing site activity or were beyond the original project scope.

  7. Final report: survey and removal of radioactive surface contamination at environmental restoration sites, Sandia National Laboratories/New Mexico. Volume 1

    International Nuclear Information System (INIS)

    Lambert, K.A.; Mitchell, M.M.; Jean, D.; Brown, C.; Byrd, C.S.

    1997-09-01

    This report describes the survey and removal of radioactive surface contamination at Sandia's Environmental Restoration (ER) sites. Radiological characterization was performed as a prerequisite to beginning the Resource Conservation and Recovery Act (RCRA) corrective action process. The removal of radioactive surface contamination was performed in order to reduce potential impacts to human health and the environment. The predominant radiological contaminant of concern was depleted uranium (DU). Between October 1993 and November 1996 scanning surface radiation surveys, using gamma scintillometers, were conducted at 65 sites covering approximately 908 acres. A total of 9,518 radiation anomalies were detected at 38 sites. Cleanup activities were conducted between October 1994 and November 1996. A total of 9,122 anomalies were removed and 2,072 waste drums were generated. The majority of anomalies not removed were associated with a site that has subsurface contamination beyond the scope of this project. Verification soil samples (1,008 total samples) were collected from anomalies during cleanup activities and confirm that the soil concentration achieved in the field were far below the target cleanup level of 230 pCi/g of U-238 (the primary constituent of DU) in the soil. Cleanup was completed at 21 sites and no further radiological action is required. Seventeen sites were not completed since cleanup activities wee precluded by ongoing site activity or were beyond the original project scope

  8. Geochemistry, biota and natural background levels in an arsenic naturally contaminated volcanic aquifer

    Science.gov (United States)

    Preziosi, Elisabetta; Amalfitano, Stefano; Di Lorenzo, Tiziana; Parrone, Daniele; Rossi, David; Ghergo, Stefano; Lungarini, Silvia; Zoppini, Anna Maria

    2015-04-01

    The tight links between chemical and ecological status are largely acknowledged as for surface water bodies, while aquifers are still considered as hidden groundwater reservoirs, rather than ecosystems to be preserved. Geochemical and biological interactions play a key role in all subterranean processes, including the dynamics of the fate of anthropogenic contaminants. Studies on groundwater dependent ecosystems (GDE) were mainly focused on karst aquifers so far, but an increased awareness on the importance of water-rock interactions and methodological improvements in microbial ecology are rapidly increasing the level of characterization of groundwater ecosystems in various hydrogeological contexts. Similarly, knowledge about groundwater biodiversity is still limited, especially if porous habitats are concerned. Yet, groundwater and GDEs are populated by a diverse and highly adapted biota, dominated by crustaceans, which provide important ecosystem services and act as biological indicators of chemical and quantitative impact on groundwater resources. In a previous research (Amalfitano et al. 2014), we reported that the microbial community heterogeneity may reflect the lithological and hydrogeological complexity within volcanic and alluvial facies transition in a groundwater body. The quantitative tracking of the microbial community structure allowed disentangling the natural biogeochemical processes evolving within the aquifer flow path. The analyses of groundwater crustaceans assemblages may contribute to shed more light upon the state and dynamics of such ecosystems. In the present research, a comprehensive study of a water table aquifer flowing through a quaternary volcanic district is being performed, including the geochemical (inorganic) composition, the microbial composition, and the analysis of crustacean assemblages . Groundwater samples are periodically collected from private wells and springs under a low anthropic impact. The key issues within the

  9. Dose coefficients and derived guidance and clinical decision levels for contaminated wounds

    Energy Technology Data Exchange (ETDEWEB)

    Bertelli, Luiz [Los Alamos National Laboratory; Toohey, Richard E [ORISE/ORAU; Sugarman, Steven A [ORISE/ORAU; Christensen, Doran R [ORISE/ORAU

    2009-01-01

    The NCRP Wound Model describing the retention of selected radionuclides at the site of a contaminated wound and their uptake into the transfer compartment has been combined with the ICRP element-specific systemic models for those radionuclides to derive dose coefficients for intakes via contaminated wounds. Those coefficients have been used to generate derived guidance levels (i.e., the activity in a wound that would result in an effective dose of 20 or 50 mSv, or in some cases, a committed organ equivalent dose of 500 mSv), and clinical decision levels (i.e., activity levels that would indicate the need for consideration of medical intervention to remove activity from the wound site or administration of decorporation therapy or both), typically set at 5 times the derived guidance levels. Data are provided for the radionuclides commonly encountered at nuclear power plants and nuclear weapons, fuel fabrication or recycling, waste disposal, medical and research facilities. These include: {sup 60}Co, {sup 90}Sr, {sup 99m}Tc, {sup 131}I, {sup 137}Cs, {sup 192}Ir, {sup 210}Po, {sup 226,228}Ra, {sup 228,232}Th, {sup 235,238}U, {sup 237}Np, {sup 238,239}Pu, {sup 241}Am, {sup 242,244}Cm, and {sup 252}Cf.

  10. The radioactive contamination level in Croatia by means of radioactive rainwaters, caused by the accident in NPP 'Lenin'

    International Nuclear Information System (INIS)

    Barishicj, D.; Koshuticj, K.; Kvastek, K.; Lulicj, S.; Tuta, J.; Vertachnik, A.; Vrhovac, A.

    1987-01-01

    In this paper, the radioactive contamination level in Croatia by means of radioactive rainwaters, caused by the accident in NPP 'Lenin', has been described. The results represent the sum of measured and evaluated data, the map of the radioactive contamination in Croatia caused by radioactive rainwaters between April, 28 to May, 20 1986 has been constructed. (author) 3 tabs.; 5 figs

  11. Fifth international conference on radioactive waste management and environmental remediation -- ICEM '95: Proceedings. Volume 2: Management of low-level waste and remediation of contaminated sites and facilities

    International Nuclear Information System (INIS)

    Slate, S.; Baker, R.; Benda, G.

    1995-01-01

    The objective of this conference is the broad international exchange of information on technologies, operations, management approaches, economics, and public policies in the critical areas of radioactive waste management and environmental remediation. The ICEM '95 technical program includes four parallel program tracks: Low/intermediate-level waste management; High-level waste, spent fuel, nuclear material management; Environmental remediation and facility D and D; and Major institutional issues in environmental management. Volume 2 contains approximately 200 papers divided into the following topical sections: Characterization of low and intermediate level waste; Treatment of low and intermediate level waste; LLW disposal and near-surface contaminant migration; Characterization and remediation of contaminated sites; and Decontamination and decommissioning technologies and experience. Papers have been processed separately for inclusion on the data base

  12. A method for determining allowable residual contamination levels of radionuclide mixtures in soil

    International Nuclear Information System (INIS)

    Napier, B.A.

    1982-05-01

    An important consideration in the disposal of radioactive wastes, and consequently in the preparation of plans for remedial actions at contaminated sites, is the amount of radioactive contamination that may be allowed to remain at any particular waste site. The allowable residual contamination level (ARCL) is dependent on the radiation dose limit imposed, the physical and environmental characteristics of the waste site, and the time at which exposure to the wastes is assumed to occur. The steps in generating an ARCL are generally as follows: (1) develop plausible, credible site-specific exposure scenario; (2) calculate maximum annual radiation doses to an individual for each radionuclide based on the existing physical characteristics of the waste site and the site-specific exposure scenario; (3) calculate the ARCL for the dose limit desired, including all radionuclides present, uncorrected for site cleanup or barrier considerations; and (4) apply any corrections for proposed cleanup activity or addition of barriers to waste migration or uptake to obtain the ARCL applicable to the proposed action. Use of this method allows appropriate application of resources to achieve uniform compliance with a single regulatory standard, i.e., a radiation dose rate limit. Application and modification of the ARCL method requires appropriate models of the environmental transport and fate of radionuclides. Example calculations are given for several specific waste forms and waste site types in order to demonstrate the technique and generate comparisons with other approaches

  13. Near-surface seismic surveys at Rifle, Colorado for shallow groundwater contamination risk assessment

    Science.gov (United States)

    Chen, J.; Zelt, C. A.; Levander, A.

    2013-12-01

    In August 2012, we carried out a series of seismic surveys at a site located approximately 0.3 mile east of the city of Rifle in Garfield County, Colorado. The ground water beneath this site was contaminated by former vanadium and uranium ore-processing operations from 1924 through 1958. The site is on an alluvial terrace created by a flood-plain meander of the Colorado River. On the south side, the terrace is bounded by a steep descending slope to the Colorado River; on the other sides, it is bounded by ascending slopes of the more resistant sedimentary rocks of the Wasatch Formation. Although remedial actions have been taken to remove the contaminated surface materials, there are still potential risks from residual materials and redistribution of the contaminated water harming human health. This seismic project, funded by The U.S. Department of Energy, was designed to provide hydrogeologic information through sub-surface velocity model building and imaging of the water aquifer. A 3D compressional wave seismic survey covers an area that is 96 m in the N-S direction by 60 m in the E-W direction. An orthogonal, symmetric receiver and source template was used with 24 receiver lines, 96 channels per receiver line, and 2.5 m between lines. The inline shot and receiver spacing is 2 m and 1 m, respectively. The source was an accelerated weight drop striking a metal plate. The source has a dominant frequency at ~60 Hz, and is down by 20 db at 20 Hz and 150 Hz, providing data suitable for seismic tomography and seismic migration methods. Besides this 3D survey, three other seismic experiments were performed: (1) a 2D multi-component source and receiver survey, (2) a 3D surface wave experiment using 4.5 Hz geophones, and (3) an ambient noise experiment using 4.5 Hz geophones to record passing vehicles and trains. Preliminary results of the data analysis will be presented.

  14. DDT in zebra mussels from Lake Maggiore (N. Italy): level of contamination and endocrine disruptions.

    Science.gov (United States)

    Binelli, Andrea; Bacchetta, Renato; Mantecca, Paride; Ricciardi, Francesco; Provini, Alfredo; Vailati, Giovanni

    2004-08-10

    The DDT contamination of Lake Maggiore (Northern Italy) has been monitored since a serious pollution event occurred in 1996. To assess the environmental risk associated with this contamination, bioaccumulation data coupled with histopathological markers were evaluated on zebra mussel populations from two different contaminated sites from April 2001 to April 2002. Biomonitoring results showed high DDT pollution in 2001 because of a flood which transported DDTs still contained in the sediments of a polluted river to the lake. DDT concentrations reached values of 4-5 microg/g lipids, higher than those recorded in other industrialized countries but comparable to levels measured in developing ones. In the ovaries of the most highly polluted mussels, histological analyses showed a delay in oocyte maturation and a high incidence of pathological pictures mainly referable to oocyte degeneration and haemocytic infiltration. Moreover, despite the presence of mature sperms, in 2001 first male gamete release occurred about 2 months later than in females. These results indicated a neuroendocrine interference of DDT on Dreissena polymorpha reproduction and also showed that these invertebrates can be successfully used to evaluate ecological implications due to exposure to endocrine disruptors in freshwater environments.

  15. Fabrication and characterization of multi-level hierarchical surfaces.

    Science.gov (United States)

    Bhushan, Bharat; Lee, Hyungoo

    2012-01-01

    A nanostructured surface may exhibit low adhesion or high adhesion depending upon fibrillar density, and it presents the possibility of realizing eco-friendly surface structures with desirable adhesion by mimicking the mechanics of fibrillar adhesive surfaces of biological systems. The current research uses a patterning technique to fabricate smart adhesion surfaces: one-, two- and three-level hierarchical synthetic adhesive structure surfaces with various fibrillar densities and diameters. The contact angles and contact angle hysteresis were measured to characterize the wettability. A conventional and a glass ball attached to an atomic force microscope (AFM) tip were used to obtain the adhesive forces via force-distance curves and to study the buckling behavior of a single fiber on the hierarchical structures.

  16. Incidence and Levels of Deoxynivalenol, Fumonisins and Zearalenone Contaminants in Animal Feeds Used in Korea in 2012

    Directory of Open Access Journals (Sweden)

    Dong-Ho Kim

    2013-12-01

    Full Text Available The objective of this study was to evaluate the occurrence and levels of deoxynivalenol (DON, fumonisins B1 and B2 (FBs, and zearalenone (ZEN contaminants in animal feeds used in Korea in 2012. Contamination with DON was observed in 91.33% and 53.33% in compound feeds and feed ingredients, respectively. Among compound feeds, poultry layer feed (laying exhibited the highest contaminant level of 1.492 mg/kg. FBs contaminants were present in compound feeds and feed ingredients at 93.33% and 83.33%, respectively. Most poultry broiler (early feeds were highly contaminated with FBs, and one of these feeds detected the level as 12.823 mg/kg as the highest level. The levels of ZEN in compound feeds and feed ingredients were 71.33% and 47%, respectively. Ninety-eight percent of compound feeds for cattle were contaminated with ZEN, and the highest contamination level of 0.405 mg/kg was observed in cattle fatting feeds.

  17. Radioactive contamination monitor

    International Nuclear Information System (INIS)

    Hasegawa, Toru; Hashimoto, Tadao; Hashimoto, Manabu

    2007-01-01

    In order to prevent radioactive materials from spreading contamination from nuclear power plants outside the radiation control area, the surface contamination of all material transferred outside from the control area is monitored. This paper presents an overview and describes features of: (1) personnel surface contamination monitoring assemblies for measuring the surface contamination on workers, (2) article surface contamination monitoring assemblies for measuring the surface contamination on articles, (3) laundry monitors for measuring the surface contamination on worker clothes worn inside the control area, and (4) hand-foot-clothing contamination monitors for measuring the surface contamination on hands, feet and clothing. (author)

  18. Cytogenetic damage related to low levels of methyl mercury contamination in the Brazilian Amazon

    Directory of Open Access Journals (Sweden)

    AMORIM MARÚCIA I. M.

    2000-01-01

    Full Text Available The mercury rejected in the water system, from mining operations and lixiviation of soils after deforestation, is considered to be the main contributors to the contamination of the ecosystem in the Amazon Basin. The objectives of the present study were to examine cytogenetic functions in peripheral lymphocytes within a population living on the banks of the Tapajós River with respect to methylmercury (MeHg contamination, using hair mercury as a biological indicator of exposure. Our investigation shows a clear relation between methylmercury contamination and cytogenetic damage in lymphocytes at levels well below 50 micrograms/gram, the level at which initial clinical signs and symptoms of mercury poisoning occur. The first apparent biological effect with increasing MeHg hair level was the impairment of lymphocyte proliferation measured as mitotic index (MI. The relation between mercury concentration in hair and MI suggests that this parameter, an indicator of changes in lymphocytes and their ability to respond to culture conditions, may be an early marker of cytotoxicity and genotoxicity in humans and should be taken into account in the preliminary evaluation of the risks to populations exposed in vivo. This is the first report showing clear cytotoxic effects of long-term exposure to MeHg. Although the results strongly suggest that, under the conditions examined here, MeHg is both a spindle poison and a clastogen, the biological significance of these observations are as yet unknown. A long-term follow-up of these subjects should be undertaken.

  19. Mechanism study of initial filamentary damage in optical components owing to surface contamination particles

    Science.gov (United States)

    Sun, Xiaoyan; Lei, Zemin; Lu, Xingqiang; Fan, Dianyuan

    2015-07-01

    Contaminations existing inevitably in high-power laser facilities modulate laser beams and decrease beam quality. This study set up a detection system to study the mechanism of initial filamentary damage in optical components induced by surface contaminations. The effect of ordinary solid particles, liquid particles, and solid-liquid mixed particles on the near-field intensity distribution of laser beam was studied and analyzed statistically. The experiment results show that pure solid particles make the beam generate diffraction rings with dark center usually in the shadow of the particles which is a weak intensity modulation; pure liquid particles focus the localized beam into a bright spot rapidly, but it is diffracted away soon; solid-liquid mixed particles cause diffraction rings with strongly bright center, but the high local intensity can be diffracted away only after a longer distance, which is one of the reason that induces the initial filamentary damage to optical components. The research results can predict the likelihood of component damage, and the corresponding preventive measures help to keep the safe operation of high-power laser facilities.

  20. Mechanism of cell integration on biomaterial implant surfaces in the presence of bacterial contamination.

    Science.gov (United States)

    Yue, Chongxia; van der Mei, Henny C; Kuijer, Roel; Busscher, Henk J; Rochford, Edward T J

    2015-11-01

    Bacterial contamination during biomaterial implantation is often unavoidable, yielding a combat between cells and bacteria. Here we aim to determine the modulatory function of bacterial components on stem-cell, fibroblast, and osteoblast adhesion to a titanium alloy, including the role of toll-like-receptors (TLRs). Presence of heat-sacrificed Staphylococcus epidermidis, Staphylococcus aureus, Escherichia coli, or Pseudomonas aeruginosa induced dose and cell-type dependent responses. Stem-cells were most sensitive to bacterial presence, demonstrating decreased adhesion number yet increased adhesion effort with a relatively large focal adhesion contact area. Blocking TLRs had no effect on stem-cell adhesion in presence of S. aureus, but blocking both TLR2 and TLR4 induced an increased adhesion effort in presence of E. coli. Neither lipopolysaccharide, lipoteichoic acid, nor bacterial DNA provoked the same cell response as did whole bacteria. Herewith we suggest a new mechanism as to how biomaterials are integrated by cells despite the unavoidable presence of bacterial contamination. Stimulation of host cell integration of implant surfaces may open a new window to design new biomaterials with enhanced healing, thereby reducing the risk of biomaterial-associated infection of both "hardware-based" implants as well as of tissue-engineered constructs, known to suffer from similarly high infection risks as currently prevailing in "hardware-based" implants. © 2015 Wiley Periodicals, Inc.

  1. Assessment of metals contamination in Klang River surface sediments by using different indexes

    Directory of Open Access Journals (Sweden)

    Abolfazl Naji

    2011-01-01

    Full Text Available Surface sediments (0-5 cm from 21 stations throughout Klang River were sampled for metal concentration as well sediment's pH, total organic carbon (TOC and particles sizes to obtain an overall classification of metal contaminations in the area. The concentration of metals (µg∕g, Fe%, dw were as follows: 0.57- 2.19 Cd; 31.89-272.33 Zn; 5.96-24.47 Ni; 10.57- 52.87 Cu; 24.23-64.11 Pb and 1.56-3.03 Fe. The degree of sediment contaminations were computed using an enrichment factor (EF and geoaccumulation index (Igeo. The results suggested that enrichment factor and geoaccumulation values of Cd were greatest among the studied metals. Pearson's correlation indicated that effectiveness of TOC in controlling the distribution and enrichment of metals was a more important factor than that of the grain size (< 63µm. The study revealed that on the basis of computed indexes, Klang River is classified as moderately polluted river.

  2. Estimation of the amount of surface contamination of a water cooled nuclear reactor by cooling water analysis

    Energy Technology Data Exchange (ETDEWEB)

    Nagy, G. [KFKI Atomic Energy Research Institute, P.O. Box 49, Budapest H-1525 (Hungary)]. E-mail: nagyg@sunserv.kfki.hu; Somogyi, A. [KFKI Atomic Energy Research Institute, P.O. Box 49, Budapest H-1525 (Hungary); Patek, G. [Paks Nuclear Power Plant, P.O. Box 71, Paks H-7031 (Hungary); Pinter, T. [Paks Nuclear Power Plant, P.O. Box 71, Paks H-7031 (Hungary); Schiller, R. [KFKI Atomic Energy Research Institute, P.O. Box 49, Budapest H-1525 (Hungary)

    2007-06-15

    Calculations, based upon on-the-spot measurements, were performed to estimate the contamination of NPP primary circuit and spent fuel storage pool solid surfaces via the composition of the cooling water in connection with a non-nuclear incident in the Paks NPP. Thirty partially burnt-up fuel element bundles were damaged during a cleaning process, an incident which resulted in the presence of fission products in the cooling water of the cleaning tank (CT) situated in a separate pool (P1). Since this medium was in contact for an extended period of time with undamaged fuel elements to be used later and also with other structural materials of the spent fuel storage pool (SP), it was imperative to assess the surface contamination of these latter ones with a particular view to the amount of fission material. In want of direct methods, one was restricted to indirect information which rested mainly on the chemical and radiochemical data of the cooling water. It was found that (i) the most important contaminants were uranium, plutonium, cesium and cerium; (ii) after the isolation of P1 and SP and an extended period of filtering the only important contaminants were uranium and plutonium; (iii) the surface contamination of the primary circuit (PC) was much lower than that of either SP or P1; (iv) some 99% of the contamination was removed from the water by the end of the filtering process.

  3. Application of gelatin zymography for evaluating low levels of contaminating neutrophils in red blood cell samples.

    Science.gov (United States)

    Achilli, Cesare; Ciana, Annarita; Balduini, Cesare; Risso, Angela; Minetti, Giampaolo

    2011-02-15

    Supposedly "homogeneous" red blood cell (RBC) samples are commonly obtained by "washing" whole blood free of plasma, platelets, and white cells with physiological solutions, a procedure that does not result, however, in sufficient removal of polymorphonuclear neutrophils (PMNs), leading to possible artifactual results. Pure RBC samples can be obtained only by leukodepletion procedures. Proposed here is a version of gelatin zymography adapted to detect matrix metalloproteinase 9 (MMP-9), selectively expressed by PMNs, in heterogeneous mixtures of RBCs and PMNs that can reveal contamination at levels as low as 1 PMN/10⁶ RBCs. Copyright © 2010 Elsevier Inc. All rights reserved.

  4. Absorption of technetium by plants in relation to soil type contamination level and time

    Energy Technology Data Exchange (ETDEWEB)

    Mousny, J.M.; Myttenaere, C. (Louvain Univ. (Belgium). Lab. de Physiologie Vegetale)

    1981-01-01

    Plants of Pisum sativum (var. Merveille de Kelvedon) were grown on seven typical european soils contaminated with different levels of /sup 99/Tc(0.17; 1.7 and 17 ..mu..Ci/kg). Added initially as pertechnetate, the technetium absorption has been studied for three successive cultures. The translocation of technetium from soil to plant leaves is high, but its transfer is reduced in soils rich in organic matter (Fen) or poorly drained (Braunerde). Aging reduces the technetium transfer and modify its relative distribution in plant (relatively more technetium is found in fruits); these results let suppose some modification of the technetium chemical form in soils with time.

  5. Levels and distribution of organohalogenated contaminants in 5 fish species from Sir Dam Lake, Kahramanmaras, Turkey

    Energy Technology Data Exchange (ETDEWEB)

    Erdogrul, Oe. [Faculty of Agriculture, Kahramanmaras (Turkey). Dept. of Food Engineering; Covaci, A.; Schepens, P. [Antwerp Univ. (Belgium). Toxicological Center

    2004-09-15

    In Turkey, OCPs have been used since 1945, with large quantities of these chemicals being used during the 1960s and 1970s. Since 1983, the usage of OCPs has been severely restricted or banned. Only few studies have investigated the presence of OCPs in Turkish aquatic environment, where they have been evidenced in relatively high concentrations. The aim of this study was to investigate the levels and distribution of organohalogenated contaminants in several fish species from Syr Dam Lake (Kahramanmarab, Turkey), an artificial lake with great economical importance for the region.

  6. Europium-154 contamination levels in Samarium-153-EDTMP for radionuclide therapy

    Energy Technology Data Exchange (ETDEWEB)

    Moro, L [Department of Medical Physics, Salvatore Maugeri Foundation, IRCCS, Scientific Institute of Pavia, 27100 Pavia (Italy); Fantinato, D [Department of Medical Physics, Salvatore Maugeri Foundation, IRCCS, Scientific Institute of Pavia, 27100 Pavia (Italy); Frigerio, F [Department of Industrial and Environmental Hygiene, Salvatore Maugeri Foundation, IRCCS, Scientific Institute of Pavia, 27100 Pavia (Italy); Shamhan, G [European School of Advanced Studies in Nuclear and Ionising Radiation Technologies, University Institute of Advanced Studies, 27100 Pavia (Italy); Angelovski, G [European School of Advanced Studies in Nuclear and Ionising Radiation Technologies, University Institute of Advanced Studies, 27100 Pavia (Italy)

    2006-05-15

    {sup 153}Sm-EDTMP, a useful non toxic bone seeking isotope in the palliative radionuclide therapy for bone metastases, is produced by neutron activation of enriched of {sup 152}Sm{sub 2}O{sub 3} targets. During the large-scale formation of {sup 153}Sm, however, there is a co-production of some long-lived radio nuclides, among which {sup 154}Eu is a major and inevitable radionuclide impurity. The level of {sup 154}Eu contamination was evaluated performing a gamma-ray spectrometry of a radiopharmaceutical sample and the urine of an administered patient. As expected, gamma-ray spectra revealed the presence of {sup 153}Eu in all the samples. The specific activity of {sup 153}Eu in the urine sample collected at 6 hours after injection is 21 Bq/ml and is less than 1 Bq/ml in 24 hr. The contamination levels of {sup 153}Eu, normalized to the corresponding activity of {sup 153}Sm, were 0.0012% in the residual and in the first urine sample and 0.0017% and 0.0031% at 30 and 54 hours after administration, respectively. The results of this study show that the level of the long-lived {sup 153}Eu impurity is not a limitation in the metastatic bone pain palliation due to the additional radiation dose burden, but could pose a cause of concern in case of discharging.

  7. Levels of contamination for various pollutants present in Belgian human plasma

    Energy Technology Data Exchange (ETDEWEB)

    Wouwe, N. Van; Goeyens, L. [Scientific Inst. of Public Health, Brussels (Belgium); Covaci, A. [Toxicological Center, Univ. of Antwerp, Wilrijk (Belgium); Kannan, K. [Wadsworth Center, New York State Dept. of Health, Albany, NY (United States); Gordon, J.; Chu, A. [Xenobiotic Detection System Inc., Durham, NC (United States); Eppe, G.; Pauw, E. De [Center of Analysis of residues in Traces (CART), Univ. of Liege (Belgium)

    2004-09-15

    During the last century, numerous compounds, such as polychlorinated biphenyls (PCBs) or organochlorine pesticides (OCPs), were banned because of their bioaccumulative and toxic properties, while other compounds, such as polybrominated diphenyl ethers (PBDEs), appeared on the market and consequently in the environment. The experiences gained from accidents involving PBBs, PCBs or PCDD/Fs are useful to conduct scientific investigations focused on preventing similar catastrophies with the newly introduced compounds. Several studies have reported potential increase in the concentration of PBDEs in food and wildlife. Monitoring the levels of toxic chemicals is therefore useful to understand the exposure pathways, sources and trends. The aim of the paper is to present actual contamination's levels of various pollutants in human plasma from Belgium. Several classes of pollutants, such PCDD/Fs, PCBs and OCPs were determined in 20 human plasmas. In addition, perfluorooctanesulfonate (PFOS) and related fluorochemicals, which are of current concern, were measured. Although anticipated, concentrations of PBDEs in the same samples were not yet determined. Through this study, a good approximation of the contamination level in Belgian human is given, allowing thus comparison with concentrations observed in other countries.

  8. Laser-induced damage of fused silica at 355 and 1065 nm initiated at aluminum contamination particles on the surface

    International Nuclear Information System (INIS)

    Genin, F.Y.; Michlitsch, K.; Furr, J.; Kozlowski, M.R.; Krulevitch, P.

    1997-01-01

    1-μm thick circular dots, 10-250 μm dia, were deposited onto 1.14 cm thick fused silica windows by sputtering Al through a mask. Al shavings were also deposited on the windows to investigate effects of particle-substrate adhesion. The silica windows were then illuminated repetitively using a 3-ns, 355 nm and an 8.6-ns, 1064 nm laser. The tests were conducted at near normal incidence with particles on input and output surfaces of the windows. During the first shot, a plasma ignited at the metal particle and damage initiated on the fused silica surface. The morphology of the damage at the metal dots were reproducible but different for input and output surface contamination. For input surface contamination, minor damage occurred where the particle was located; such damage ceased to grow with the removal of contaminant material. More serious damage (pits and cracks) was initiated on the output surface (especially at 355 nm) and grew to catastrophic proportions after few shots. Output surface contaminants were usually ejected on the initial shot, leaving a wave pattern on the surface. No further damage occurred with subsequent shots unless a shot (usually the first shot) cracked the surface; such behavior was mostly observed at 355 nm and occasionally for large shavings at 1064 nm. The size of the damaged area scaled with the size of the particle (except when catastrophic damage occurred). Onset of catastrophic damage on output surface occurred only when particles exceeded a critical size. Damage behavior of the sputtered dots was found to be qualitatively similar to that of the shavings. The artificial contamination technique accelerated the study by allowing better control of the test conditions

  9. Radioecological state of some surface water systems of contaminated areas of both Gomel and Mogilev Regions

    International Nuclear Information System (INIS)

    Datskevich, P. I.; Komissariv, F. D.; Khvale', O. D.; Basharina, L. P.; Lobach, I. L.

    1997-01-01

    The radioecological situation of different ecosystems of Belarus and their components has been analysed. Such components of the surface water ecosystems as water, suspensions, sediments and soils of water-collection areas were used for the investigation of the content of cesium 137 and strontium 90. The received data were given since 1990. The content of cesium 137 and strontium 90 in the components of water ecosystems was counted in the laboratory conditions by means of standard methods of beta radiometry, semiconductor gamma spectrometry and radiochemistry. The error of measurement of radioactivity was not higher than 25 and 35% for cesium 137 and strontium 90 accordingly. Water ecosystems were distinguished by the state of contamination of water-collection areas and hydrological parameters. These and some other reasons considered in the article influence on the character of cesium 137 and strontium 90 behaviour in water ecosystems

  10. Imaging technique for detection of leaf surface contaminations with fission fragments

    International Nuclear Information System (INIS)

    Furuta, Etsuko

    2011-01-01

    Fission fragments by the Fukushima Daiichi catastrophe were scattered over a large area. Between Tokyo and Fukushima, leaves were gathered up from March to June and measured their radioactivities by HPGe. Radionuclides of 129m Tc, 131 I, 134 Cs and 137 Cs were rightly detected. Also the leaf surface contaminations were shown as images by imaging technique which detected beta- and gamma-rays exposure. The clear images were gotten within 24 h exposure though a normal leaf image needs at least one week exposure in a shield box. The total PSL values of leaves depend on their activities of sampling points, so the imaging technique is able to use for detection of the spread of fission fragments and the relative concentration. Also the rain effect to leaves could be shown by imaging technique when leaves were washed in running water. The imaging technique is easy and useful for the nuclear catastrophe. (author)

  11. Removal of Airborne Contaminants from a Surface Tank by a Push-Pull System

    DEFF Research Database (Denmark)

    Heiselberg, Per; Topp, Claus

    Open surface tanks are used in many industrial processes, and local exhaust systems are often designed to capture and remove toxic fumes diffused from materials in the tanks prior to their escape into the workplace environment. The push-pull system seems to be the most efficient local exhaust...... system, but proper design is required to ensure health and safety of the workers and, furthermore, it is very desirable from an energy conservation point of view to determine an optimum and -an efficient design of push-pull hoods which can exhaust all contaminants with a minimum quantity of volume flow....... The paper describes and discusses different design methods and compares designed values with results from a measurement series of push-pull system efficiency....

  12. Absorption and backscatter of internal conversion electrons in the measurements of surface contamination of 137Cs

    International Nuclear Information System (INIS)

    Yunoki, A.; Kawada, Y.; Yamada, T.; Unno, Y.; Sato, Y.; Hino, Y.

    2013-01-01

    We measured 4π and 2π counting efficiencies for internal conversion electrons (ICEs), gross β-particles and also β-rays alone with various source conditions regarding absorber and backing foil thickness using e-X coincidence technique. Dominant differences regarding the penetration, attenuation and backscattering properties among ICEs and β-rays were revealed. Although the abundance of internal conversion electrons of 137 Cs- 137 Ba is only 9.35%, 60% of gross counts may be attributed to ICEs in worse source conditions. This information will be useful for radionuclide metrology and for surface contamination monitoring. - Highlights: • Counting efficiencies for internal conversion electrons from 137 Cs were measured, and compared with those for β-rays. • Electron-X coincidence technique was employed. • A thin NaI(Tl) scintillation detector was used for X-ray detection. • Backscattering fractions of electrons and beta particles were studied by similar experiments

  13. Integrated Assessment of the impact of Aqueous Contaminant Stressors on Surface Water Ecosystems

    DEFF Research Database (Denmark)

    McKnight, Ursula S.; Rasmussen, Jes J.; Kronvang, Brian

    2011-01-01

    ecosystems. Traditional approaches for managing aquatic resources have often failed to account for the potential effects of anthropogenic disturbances on biota. To fulfil the requirements of the EU Water Framework Directive will be challenging, as it is difficult to successfully separate and evaluate all...... pressures stressing an ecosystem. Here, methods for determining ecological status in streams are evaluated to see if they are capable of capturing the effects of stressors potentially affecting ecosystems. Specifically, they are tested on a case study where the effects of physical habitat degradation can...... carried out in summer 2010. The campaign included an analysis of xenobiotics in surface water, inorganic chemistry, diffuse source (run-off) impacts and ecology along a gradient of contamination in the stream. Modelling results indicate that naphthalene, glyphosate and 4-nonylphenol could adversely impact...

  14. The Mobile Surface Contamination Monitor II environmental radiological characterization utilizing GPS/GIS technologies

    International Nuclear Information System (INIS)

    Wendling, M.A.

    1993-05-01

    Time, cost, and most importantly quality of data are the three factors to measure the success of field radiological characterizations. The application of coupling radiation detection instrumentation to a GPS receiver has dramatically increased the data quality achievable compared to traditional environmental radiological survey methods. Improvements in verifying adequate spatial coverage of an area while collecting data and at,the same time reducing field time requirements can be realized. Data acquired during the recent implementation of the Mobile Surface Contamination Monitor 11 (MSCM-11) will be presented to demonstrate the advantages of this system over traditional radiological survey methods. The comparison will include time and manpower requirements. Linking the complimentary GPS, GIS and radiation detection technologies on a mobile tractor based platform has provided a tool to provide radiological characterization data faster, cheaper, and better to assist in the Environmental Restoration Mission of the Hanford Site

  15. Modeling seasonal and spatial contamination of surface waters and upper sediments with trace metal elements across industrialized urban areas of the Seybouse watershed in North Africa.

    Science.gov (United States)

    Belabed, Bourhane-Eddine; Meddour, Abderrafik; Samraoui, Boudjéma; Chenchouni, Haroun

    2017-06-01

    Industrialization and urbanization are the main sources of pollutions worldwide and particularly in developing countries. This study aims the determination of anthropogenic inputs with trace metals in aquatic ecosystems at the Plain of Annaba (NE Algeria), which is known as one of the largest industrial areas in Africa. Samples of surface waters and upper sediments were conducted in six stations: four in Meboudja wadi and two in Seybouse wadi. Contents of iron, copper, chromium, nickel, zinc, and manganese were measured by atomic absorption spectrophotometry, whereas Cd and Pb were determined using electrothermal atomic absorption spectrometry. Measurements of Hg were carried out using atomic fluorescence. Spatiotemporal variations of metal concentrations were tested using generalized linear models (GLM), whereas the influence of water pollution on sediment contamination was tested with generalized additive models (GAMs). Metal contents measured in surface water and sediments varied differently from upstream to downstream of the study wadis and between seasons. The results showed that the surface water was polluted with high levels of iron, nickel, chromium, lead, and cadmium. Values of the contamination index revealed that the surface sediments were contaminated by iron, chromium, lead, and cadmium. The GAMs indicated that water-phase metal concentrations had no significant effects on trace metal concentrations in the sediment. This suggests that seasonal metal concentrations in water phase, which are measured during the study period (2012) and are time-dependent, contribute increasingly and gradually over time-not immediately-to the accumulation of metals into the sediments. Therefore, the long-term accumulation of metals in the sediments resulted from the continuous discharges of metals in the water phase. The anthropogenic impacts are marked by high contaminations of Meboudja wadi particularly in downstream areas of the steel factory and the nearby industrial

  16. Estimation of Potential Population Level Effects of Contaminants on Wildlife; FINAL

    International Nuclear Information System (INIS)

    Loar, J.M.

    2001-01-01

    The objective of this project is to provide DOE with improved methods to assess risks from contaminants to wildlife populations. The current approach for wildlife risk assessment consists of comparison of contaminant exposure estimates for individual animals to literature-derived toxicity test endpoints. These test endpoints are assumed to estimate thresholds for population-level effects. Moreover, species sensitivities to contaminants is one of several criteria to be considered when selecting assessment endpoints (EPA 1997 and 1998), yet data on the sensitivities of many birds and mammals are lacking. The uncertainties associated with this approach are considerable. First, because toxicity data are not available for most potential wildlife endpoint species, extrapolation of toxicity data from test species to the species of interest is required. There is no consensus on the most appropriate extrapolation method. Second, toxicity data are represented as statistical measures (e.g., NOAEL s or LOAELs) that provide no information on the nature or magnitude of effects. The level of effect is an artifact of the replication and dosing regime employed, and does not indicate how effects might increase with increasing exposure. Consequently, slight exceedance of a LOAEL is not distinguished from greatly exceeding it. Third, the relationship of toxic effects on individuals to effects on populations is poorly estimated by existing methods. It is assumed that if the exposure of individuals exceeds levels associated with impaired reproduction, then population level effects are likely. Uncertainty associated with this assumption is large because depending on the reproductive strategy of a given species, comparable levels of reproductive impairment may result in dramatically different population-level responses. This project included several tasks to address these problems: (1) investigation of the validity of the current allometric scaling approach for interspecies extrapolation

  17. The technique for determination of surface contamination by uranium on U3Si2-Al plate-type fuel elements

    International Nuclear Information System (INIS)

    Li Shulan; He Fengqi; Wang Qingheng; Han Jingquan

    1993-04-01

    The NDT method for determining the surface contamination by uranium on U 3 Si 2 -Al plate-type fuel elements, the process of standard specimen preparation and the graduation curve are described. The measurement results of U 3 Si 2 -Al plate-type fuel elements show that the alpha counting method to measure the surface contamination by uranium on fuel plate is more reliable. The UB-1 type surface contamination meter, which was recently developed, has many advantages such as high sensitivity to determine the uranium pollution, short time in measuring, convenience for operation, and the minimum detectable amount of uranium is 5 x 10 -10 g/cm 2 . The measuring device is controlled by a microcomputer. Besides data acquisition and processing, it has functions of statistics, output data on terminal or to printer and alarm. The procedures of measurement are fully automatic. All of these will meet the measuring needs in batch process

  18. A siphon gage for monitoring surface-water levels

    Science.gov (United States)

    McCobb, T.D.; LeBlanc, D.R.; Socolow, R.S.

    1999-01-01

    A device that uses a siphon tube to establish a hydraulic connection between the bottom of an onshore standpipe and a point at the bottom of a water body was designed and tested for monitoring surface-water levels. Water is added to the standpipe to a level sufficient to drive a complete slug of water through the siphoning tube and to flush all air out of the system. The water levels in the standpipe and the water body equilibrate and provide a measurable static water surface in the standpipe. The siphon gage was designed to allow quick and accurate year-round measurements with minimal maintenance. Currently available devices for monitoring surface-water levels commonly involve time-consuming and costly installation and surveying, and the movement of reference points and the presence of ice cover in cold regions cause discontinuity and inaccuracy in the data collected. Installation and field testing of a siphon gage using 0.75-in-diameter polyethylene tubing at Ashumet Pond in Falmouth, Massachusetts, demonstrated that the siphon gage can provide long-term data with a field effort and accuracy equivalent to measurement of ground-water levels at an observation well.A device that uses a siphon tube to establish a hydraulic connection between the bottom of an onshore standpipe and a point at the bottom of a water body was designed and tested for monitoring surface-water levels. Water is added to the standpipe to a level sufficient to drive a complete slug of water through the siphoning tube and to flush all air out of the system. The water levels in the standpipe and the water body equilibrate and provide a measurable static water surface in the standpipe. The siphon gage was designed to allow quick and accurate year-round measurements with minimal maintenance. Currently available devices for monitoring surface-water levels commonly involve time-consuming and costly installation and surveying, and the movement of reference points and the presence of ice cover in cold

  19. Anatomic-physiological schema of the gastrointestinal tract, to be taken in account in determining the levels of radioactive contamination

    International Nuclear Information System (INIS)

    Fabry, C.

    1964-01-01

    Anatomical and physiological data of the gastrointestinal tract of adults and children were summarized in a standard schema, to be used in calculating the levels of radioactive contamination, in the food chain. (author) [fr

  20. Functional gene array-based analysis of microbial community structure in groundwaters with a gradient of contaminant levels

    Energy Technology Data Exchange (ETDEWEB)

    Waldron, P.J.; Wu, L.; Van Nostrand, J.D.; Schadt, C.W.; Watson, D.B.; Jardine, P.M.; Palumbo, A.V.; Hazen, T.C.; Zhou, J.

    2009-06-15

    To understand how contaminants affect microbial community diversity, heterogeneity, and functional structure, six groundwater monitoring wells from the Field Research Center of the U.S. Department of Energy Environmental Remediation Science Program (ERSP; Oak Ridge, TN), with a wide range of pH, nitrate, and heavy metal contamination were investigated. DNA from the groundwater community was analyzed with a functional gene array containing 2006 probes to detect genes involved in metal resistance, sulfate reduction, organic contaminant degradation, and carbon and nitrogen cycling. Microbial diversity decreased in relation to the contamination levels of the wells. Highly contaminated wells had lower gene diversity but greater signal intensity than the pristine well. The microbial composition was heterogeneous, with 17-70% overlap between different wells. Metal-resistant and metal-reducing microorganisms were detected in both contaminated and pristine wells, suggesting the potential for successful bioremediation of metal-contaminated groundwaters. In addition, results of Mantel tests and canonical correspondence analysis indicate that nitrate, sulfate, pH, uranium, and technetium have a significant (p < 0.05) effect on microbial community structure. This study provides an overall picture of microbial community structure in contaminated environments with functional gene arrays by showing that diversity and heterogeneity can vary greatly in relation to contamination.

  1. Immobilized enzymes: understanding enzyme - surface interactions at the molecular level.

    Science.gov (United States)

    Hoarau, Marie; Badieyan, Somayesadat; Marsh, E Neil G

    2017-11-22

    Enzymes immobilized on solid supports have important and industrial and medical applications. However, their uses are limited by the significant reductions in activity and stability that often accompany the immobilization process. Here we review recent advances in our understanding of the molecular level interactions between proteins and supporting surfaces that contribute to changes in stability and activity. This understanding has been facilitated by the application of various surface-sensitive spectroscopic techniques that allow the structure and orientation of enzymes at the solid/liquid interface to be probed, often with monolayer sensitivity. An appreciation of the molecular interactions between enzyme and surface support has allowed the surface chemistry and method of enzyme attachement to be fine-tuned such that activity and stability can be greatly enhanced. These advances suggest that a much wider variety of enzymes may eventually be amenable to immobilization as green catalysts.

  2. An integrated model for assessing the risk of TCE groundwater contamination to human receptors and surface water ecosystems

    DEFF Research Database (Denmark)

    McKnight, Ursula S.; Funder, S.G.; Rasmussen, J.J.

    2010-01-01

    The practical implementation of the European Water Framework Directive has resulted in an increased focus on the hyporheic zone. In this paper, an integrated model was developed for evaluating the impact of point sources in groundwater on human health and surface water ecosystems...... will not be depleted for many decades, however measured and predicted TCE concentrations in surface water were found to be below human health risk management targets. Volatilization rapidly attenuates TCE concentrations in surface water. Thus, only a 300 m stream reach fails to meet surface water quality criteria....... An ecological risk assessment found that the TCE contamination did not impact the stream ecosystem. Uncertainty assessment revealed hydraulic conductivity to be the most important site-specific parameter. These results indicate that contaminant plumes with μgL-1 concentrations of TCE entering surface water...

  3. Origin of metallic surface core-level shifts

    DEFF Research Database (Denmark)

    Aldén, Magnus; Skriver, Hans Lomholt; Abrikosov, I. A.

    1995-01-01

    The unique property of the open 4f energy shell in the lanthanide metals is used to show that the initial-state energy shift gives an insufficient description of surface core-level shifts. Instead a treatment, which fully includes the final-state screening, account for the experimentally observed...

  4. GWSCREEN: A semi-analytical model for assessment of the groundwater pathway from surface or buried contamination: Version 2.0 theory and user's manual

    International Nuclear Information System (INIS)

    Rood, A.S.

    1993-06-01

    GWSCREEN was developed for assessment of the groundwater pathway from leaching of radioactive and non radioactive substances from surface or buried sources. The code was designed for implementation in the Track I and Track II assessment of CERCLA (Comprehensive Environmental Response, Compensation and Liability Act) sites identified as low probability hazard at the Idaho National Engineering Laboratory (DOE, 1992). The code calculates the limiting soil concentration such that, after leaching and transport to the aquifer, regulatory contaminant levels in groundwater are not exceeded. The code uses a mass conservation approach to model three processes: contaminant release from a source volume, contaminant transport in the unsaturated zone, and contaminant transport in the saturated zone. The source model considers the sorptive properties and solubility of the contaminant. Transport in the unsaturated zone is described by a plug flow model. Transport in the saturated zone is calculated with a semi-analytical solution to the advection dispersion equation in groundwater. In Version 2.0, GWSCREEN has incorporated an additional source model to calculate the impacts to groundwater resulting from the release to percolation ponds. In addition, transport of radioactive progeny has also been incorporated. GWSCREEN has shown comparable results when compared against other codes using similar algorithms and techniques. This code was designed for assessment and screening of the groundwater pathway when field data is limited. It was not intended to be a predictive tool

  5. GWSCREEN: A semi-analytical model for assessment of the groundwater pathway from surface or buried contamination: Version 2.0 theory and user`s manual

    Energy Technology Data Exchange (ETDEWEB)

    Rood, A.S.

    1993-06-01

    GWSCREEN was developed for assessment of the groundwater pathway from leaching of radioactive and non radioactive substances from surface or buried sources. The code was designed for implementation in the Track I and Track II assessment of CERCLA (Comprehensive Environmental Response, Compensation and Liability Act) sites identified as low probability hazard at the Idaho National Engineering Laboratory (DOE, 1992). The code calculates the limiting soil concentration such that, after leaching and transport to the aquifer, regulatory contaminant levels in groundwater are not exceeded. The code uses a mass conservation approach to model three processes: contaminant release from a source volume, contaminant transport in the unsaturated zone, and contaminant transport in the saturated zone. The source model considers the sorptive properties and solubility of the contaminant. Transport in the unsaturated zone is described by a plug flow model. Transport in the saturated zone is calculated with a semi-analytical solution to the advection dispersion equation in groundwater. In Version 2.0, GWSCREEN has incorporated an additional source model to calculate the impacts to groundwater resulting from the release to percolation ponds. In addition, transport of radioactive progeny has also been incorporated. GWSCREEN has shown comparable results when compared against other codes using similar algorithms and techniques. This code was designed for assessment and screening of the groundwater pathway when field data is limited. It was not intended to be a predictive tool.

  6. Detection of contaminated metallurgical scrap at borders: a proposal for an 'investigation level'

    International Nuclear Information System (INIS)

    Duftschmid, K.E.

    1999-01-01

    In 1995 the IAEA started a program to combat illicit trafficking in nuclear and other radioactive materials which includes the problem of cross-border movement of contaminated metallurgical scrap. A major activity in this program is the elaboration of a Safety Guide on 'Preventing, Detecting and Responding to Illicit Trafficking', co-sponsored by the World Customs Organization (WCO) and INTERPOL. The guide will provide advice to the Member States, in particular on technical and administrative procedures for detection of radioactive materials at borders. Radiation monitoring systems for contaminated scrap metals have been successfully used in steel plants and larger scrap yards since several years and suitable products are on the market today. Using sophisticated software and dynamic scanning techniques such systems allow for detection of an artificial increase in radiation background level as low as by 20%, even if the natural background signal is substantially suppressed by the vehicle itself entering the monitor. However, the measurement conditions at borders are essentially different from those in plants. Large traffic crossing major borders limits the time for detection and response to a few seconds and multiple checks are nearly impractical. Shielded radioactive sources - even of high activity - which are deeply buried in scrap, cannot be detected without unloading the vehicle, a procedure generally ruled out at borders. Highly sensitive monitoring systems necessarily cause frequent false alarms or nuisance alarms due to innocent radioactive materials such as naturally occurring radioactivity e.g. in fertilizers, scale in pipes used in the oil industry or medical radioisotopes. A particular, rather frequent problem is the unnecessary reject of scrap transports on borders due to the inherent low level contamination of steel with 60 Co, even in sheet metal used for lorries or railroad cars. Such contamination can easily be caused by the routine method to control

  7. Organochlorine contaminant and retinoid levels in blubber of common dolphins (Delphinus delphis) off northwestern Spain

    International Nuclear Information System (INIS)

    Tornero, Victoria; Borrell, Assumpcio; Aguilar, Alex; Forcada, Jaume; Lockyer, Christina

    2006-01-01

    The effect of age, sex, nutritive condition and organochlorine concentration on blubber retinoid concentrations was examined in 74 common dolphins incidentally caught off northwestern Spain. Age and blubber lipid content were strong determinants of the retinoid concentrations in males, while these variables did not account for the variation found in females. Retinoids were positively correlated with organochlorines in males and negatively in females. However, pollution levels were moderate and likely to be below threshold levels above that a toxicological response is to be expected. Thus, a cause-effect relationship between organochlorine and retinoid concentrations could not be properly established, and the observed correlation may be the result of an independent association of the two variables with age. Further research on the influence of the best predictor variables on retinoid dynamics is required to implement the use of retinoids as biomarkers of pollutant exposure in cetaceans. - Organochlorine contaminants and retinoids in common dolphins

  8. Organochlorine contaminant and retinoid levels in blubber of common dolphins (Delphinus delphis) off northwestern Spain

    Energy Technology Data Exchange (ETDEWEB)

    Tornero, Victoria [Department of Animal Biology (Vertebrates), Faculty of Biology, University of Barcelona, Diagonal 645, 08071 Barcelona (Spain)]. E-mail: victoriatornero@ub.edu; Borrell, Assumpcio [Department of Animal Biology (Vertebrates), Faculty of Biology, University of Barcelona, Diagonal 645, 08071 Barcelona (Spain); Aguilar, Alex [Department of Animal Biology (Vertebrates), Faculty of Biology, University of Barcelona, Diagonal 645, 08071 Barcelona (Spain); Forcada, Jaume [Biological Sciences Division, NERC, British Antarctic Survey, High Cross, Madingley Road, Cambridge CB3 0ET (United Kingdom); Lockyer, Christina [Age Dynamics, Huldbergs Alle 42, DK-2800 Kongens, Lyngby (Denmark)

    2006-03-15

    The effect of age, sex, nutritive condition and organochlorine concentration on blubber retinoid concentrations was examined in 74 common dolphins incidentally caught off northwestern Spain. Age and blubber lipid content were strong determinants of the retinoid concentrations in males, while these variables did not account for the variation found in females. Retinoids were positively correlated with organochlorines in males and negatively in females. However, pollution levels were moderate and likely to be below threshold levels above that a toxicological response is to be expected. Thus, a cause-effect relationship between organochlorine and retinoid concentrations could not be properly established, and the observed correlation may be the result of an independent association of the two variables with age. Further research on the influence of the best predictor variables on retinoid dynamics is required to implement the use of retinoids as biomarkers of pollutant exposure in cetaceans. - Organochlorine contaminants and retinoids in common dolphins.

  9. Degree of bacterial contamination and antibiotic susceptibility pattern of isolates from housekeeping surfaces in operating rooms and surgical wards at Jimma University Specialized Hospital, south west Ethiopia.

    Science.gov (United States)

    Genet, Chalachew; Kibru, Gebre; Hemalatha, Kannan

    2012-01-01

    The role of the hospital environment as a reservoir of potential pathogens has received increasing attention. There are several reports demonstrating contamination of a wide variety of environmental sites in operating rooms (ORs) and surgical wards (SWs) which lead to nosocomial spread. To determine the degree of bacterial contamination and antibiotic susceptibility pattern of isolates from floor and tabletop surfaces in ORs and SWs at Jimma University Specialized Hospital (JUSH). A cross sectional study was conducted on 144 floor and tabletop surfaces from October to January 2009/2010. Samples were investigated for identification of bacterial species following standard procedures and antimicrobial susceptibility tests were performed using disc diffusion technique. The data was analyzed using SPSS version 16 and compared with the proposed standard value. The mean aerobic colony counts (ACCs) for tabletop surfaces (34 CFU/cm2) and floors (19CFU/cm2) in SWs were significantly higher than the set ACC standard for hand contact surfaces (< 5 CFU/cm2) P < 0.00. The ACCs obtained from tabletop surfaces (6.2 CFU/cm2) and floors (10.1CFU/cm2) in ORs were also exceeding the standard. Over 55% of gram negative bacteria were identified from Critical Zone of ORs. Staphylococcus aureus was the must frequently isolated bacterium accounting 33.3% followed by Escherichia coli and Klebsiella spp each with 11.1%. Moreover, S. aureus showed 100% resistance to methicillin and multidrug resistant Enterobacteriaceae were also seen in more than 90 % of isolates. An increased bacterial contamination was measured in both ORs and SWs of the JUSH and the isolated bacteria were also resistant for most of the antibiotics used as a treatment options in the study area. Therefore, appropriate infection control measures needs to be taken to keep the contamination level within the proposed standard.

  10. Heavy Metal Contamination in the Surface Sediments of Representative Limnetic Ecosystems in Eastern China

    Science.gov (United States)

    Tang, Wenzhong; Shan, Baoqing; Zhang, Hong; Zhang, Wenqiang; Zhao, Yu; Ding, Yuekui; Rong, Nan; Zhu, Xiaolei

    2014-11-01

    A comprehensive analysis of heavy metal pollution was conducted in the representative limnetic ecosystems of eastern China, which are subject to rapid economic development and population growth. The results demonstrated that the average contents with standard deviations of Cd, Cr, Cu, Ni, Pb and Zn in the surface sediments were 0.925 +/- 0.936, 142 +/- 46.8, 54.7 +/- 29.1, 60.5 +/- 21.6, 61.9 +/- 36.0 and 192 +/- 120 mg/kg dry wt., respectively, and that higher values were mainly observed in the southern portion of the study area, especially in the basins of Southeast Coastal Rivers (SCRB) and the Zhu River (ZRB). The six heavy metals in the surface sediments all had anthropogenic origins. In addition, the limnetic ecosystems, especially in the southern portion of the study area were found to be polluted by heavy metals, especially Cd. Overall, two hotspots of heavy metal pollution in the limnetic ecosystems of eastern China were found, one that consisted of the heavy pollution regions, SCRB and ZRB, and another composed of Cd pollution. These results indicate that heavy metal contamination, especially Cd, should be taken into account during development of management strategies to protect the aquatic environment in the limnetic ecosystems of eastern China, especially in the two aforementioned basins.

  11. Ag Nanorod Arrays for SERS: Aspects of Spectral Reproducibility, Surface Contamination, and Spectral Sensitivity

    Directory of Open Access Journals (Sweden)

    Martin Šubr

    2015-01-01

    Full Text Available Ag nanorod arrays prepared by oblique angle vapor deposition (OAD represent regular, large area substrates for surface-enhanced Raman scattering (SERS spectroscopy. We studied uniformity and spectral reproducibility of silver OAD-fabricated substrates (AgOADs by spectral mapping of methylene blue. The results demonstrate good reproducibility apart from occasional “hot-spot” sites where the intensity is higher. The number of “hot-spots” represents 2%–6% of SERS-active sites of mapping substrate area. We were able to obtain good SERS spectra of testing amino acid tryptophan at 1 × 10−5 M concentration and three different free-base porphyrins down to ∼10−7 M concentration. We found out that keeping the AgOADs in a vacuum chamber overnight prevents the surface from binding any contaminants from the ambient atmosphere, without significant reduction in the SERS enhancement. Such substrates provide stable SERS enhancement even when stored for 1 year after preparation.

  12. The BetaCage, an ultra-sensitive screener for surface contamination

    Energy Technology Data Exchange (ETDEWEB)

    Bunker, R.; Bowles, M. A.; Schnee, R. W.; Wang, B. [Department of Physics, Syracuse University, Syracuse, NY 13244 (United States); Ahmed, Z.; Golwala, S. R.; Nelson, R. H.; Rider, A.; Zahn, A. [California Institute of Technology, Pasadena, CA 91125 (United States); Grant, D. R. [University of Alberta, Edmonton, AB, T6G 2R3 (Canada); Kos, M. [Department of Physics, Syracuse University, Syracuse, NY 13244, USA and Pacific Northwest National Laboratory, Richland, WA 99352 (United States)

    2013-08-08

    Material screening for identifying low-energy electron emitters and alpha-decaying isotopes is now a prerequisite for rare-event searches (e.g., dark-matter direct detection and neutrinoless double-beta decay) for which surface radiocon-tamination has become an increasingly important background. The BetaCage, a gaseous neon time-projection chamber, is a proposed ultra-sensitive (and nondestructive) screener for alpha-and beta-emitting surface contaminants to which existing screening facilities are insufficiently sensitive. Sensitivity goals are 0.1 betas keV{sup −1} m{sup −2} day{sup −1} and 0.1 alphas m{sup −2} day{sup −1}, with the former limited by Compton scattering of photons in the screening samples and (thanks to tracking) the latter expected to be signal-limited; radioassays and simulations indicate backgrounds from detector materials and radon daughters should be subdominant. We report on details of the background simulations and detector design that provide the discrimination, shielding, and radiopurity necessary to reach our sensitivity goals for a chamber with a 95 × 95 cm{sup 2} sample area positioned below a 40 cm drift region and monitored by crisscrossed anode and cathode planes consisting of 151 wires each.

  13. Evaluation of the contribution of contamination of radiotherapy room surfaces in the measure of exposure rate of radioiodine therapy patients

    International Nuclear Information System (INIS)

    Campos, Rafael Ferreira

    2015-01-01

    The contamination of radiotherapy room surfaces is significant and the measures of patient exposure rate are held on the fourth dependencies, relevant questions are raised: the background radiation of the room stay high due to surface contamination, may interfere with the rate of patient exposure at the time of its release? The monitoring site is important to determine whether the patient will be released? The value of the deal activity and the clinical condition of the patient may increase the contamination, influencing the monitoring results? This paper aims to conduct a quantitative analysis of surface contamination of the contribution of therapeutic room at the time is monitored exposure rate from inpatient. Measurements were made regarding the hospitalization of 32 patients with different doses administered activity, age and of both genders. The measurements were performed in the therapeutic rooms at the hospital Brotherhood Santa Casa de Misericordia de Sao Paulo. Exposure rate measurements were performed at the center of the room at 1 meter of the patient on the day of its release. After his release and prior to decontamination, measurements were performed at predetermined landmarks within the therapeutic room. The results revealed that on average background radiation, high due to surface contamination contributes only 2% of the patient dose rate. It can be considered that even with influence of contamination of surfaces, this is insignificant to determine if the patient may or may not be released. This study suggests that the site in which monitoring occurs exposure rate of the patient should not be decisive for liberation thereof. (author)

  14. Evaluation of the homogeneity of reference flat sources used in calibration of surface contamination monitors

    International Nuclear Information System (INIS)

    Silva Junior, I.A.; Xavier, M.; Siqueira, P.T.D.; Potiens, M.P.A.

    2014-01-01

    The aim of this study was to re-evaluate the uniformity of the wide area reference sources of the Calibration Laboratory of Instruments (LCI-IPEN) used in the calibration of surface contamination monitors, according the recommendations of the ISO 8769 standard and the NRPB. In this work used six wide area reference sources of 150 cm 2 of 241 Am, 14 C, 36 Cl, 137 Cs, 90 Sr+ 90 Y and 99 Tc with reference dates between 1996 and 1997 and three sources of 100 cm 2 of 14 C, 137 Cs and 60 Co were used with reference dates 2007. Measurements were performed with a radiation monitor of the Thermo, model FH40GX with a pancake probe, model FHZ732GM. We also made several models on paper with the objective of define each measurement position and an aluminum plate with a square hole (6.25 cm 2 ) in its center, allowing the passage of the radiation only through the hole. Each wide area reference source was positioned in setup and measurements were performed in order to cover the entire surface of the source. The values of the uniformity obtained partially confirm previous data obtained in another study conducted by LCI-IPEN, showing that some wide area reference sources 150 cm 2 in disagree with ISO 8769. In the former work, just the source of 241 Am (7.3%) was within the range specified by the standard, now have sources of 241 Am (5.7%), 137 Cs (8.8%), 90 Sr+ 9 '0Y (8, 8%) and 99 Tc (9.2%) with values within the specified uniformity. The sources of 14 C (53.3%) and 36 Cl (16.6%) were outside the specified. The wide area reference sources of 100 cm 2 , show disagreement in values of uniformity of the sources 14 C (46.7%) and 60 Co (10.4%). The values of the uniformity of the wide area reference sources show that some fonts can not be used in calibrations, because not in accordance with the value of uniformity specified in ISO 8769:2010, this is a conditions to believe a laboratory according to ISO 17025, show the laboratory performs its services with a high quality. The

  15. Mercury contamination in human hair and fish from Cambodia: levels, specific accumulation and risk assessment

    International Nuclear Information System (INIS)

    Agusa, Tetsuro; Kunito, Takashi; Iwata, Hisato; Monirith, In; Tana, Touch Seang; Subramanian, Annamalai; Tanabe, Shinsuke

    2005-01-01

    Mercury (Hg) concentrations in human hair and fish samples from Phnom Penh, Kien Svay, Tomnup Rolork and Batrong, Cambodia, collected in November 1999 and December 2000 were determined to understand the status of contamination, and age- and sex-dependent accumulation in humans and to assess the intake of mercury via fish consumption. Mercury concentrations in human hair ranged from 0.54 to 190 μg/g dry wt. About 3% of the samples contained Hg levels exceeding the no observed adverse effects level (NOAEL) of WHO (50 μg/g) and the levels in some hair samples of women also exceeded the NOAEL (10 μg/g) associated with fetus neurotoxicity. A weak but significant positive correlation was observed between age and Hg levels in hair of residents. Mercury concentrations in muscle of marine and freshwater fish from Cambodia ranged from <0.01 to 0.96 μg/g wet wt. Mercury intake rates were estimated on the basis of the Hg content in fish and daily fish consumption. Three samples of marine fish including sharp-tooth snapper and obtuse barracuda, and one sample of sharp-tooth snapper exceeded the guidelines by US EPA and by Joint FAO/WHO Expert Committee on Food Additives (JECFA), respectively, which indicates that some fish specimens examined (9% and 3% for US EPA and JECFA guidelines, respectively) were hazardous for consumption at the ingestion rate of Cambodian people (32.6 g/day). It is suggested that fish is probably the main source of Hg for Cambodian people. However, extremely high Hg concentrations were observed in some individuals and could not be explained by Hg intake from fish consumption, indicating some other contamination sources of Hg in Cambodia. - A source other than fish may be responsible for high Hg in some Cambodians

  16. Assessment of lead, cadmium, and zinc contamination of roadside soils, surface films, and vegetables in Kampala City, Uganda

    International Nuclear Information System (INIS)

    Nabulo, Grace; Oryem-Origa, Hannington; Diamond, Miriam

    2006-01-01

    The relationship between traffic density and trace metal concentrations in roadside soils, surface films, and a selected vegetable weed, Amaranthus dubius Mart. Ex Thell., was determined in 11 farming sites along major highways around Kampala City in Uganda. Surface soil, atmospherically deposited surface films on windows, and leaves of Amaranthus dubius were sampled at known distances from the roads and analyzed for lead (Pb), zinc (Zn), and cadmium (Cd) using flame atomic absorption spectrophotometry. Atmospherically deposited trace metal particulates were sampled using window glass as an inert, passive collector. Total trace metal concentrations in soils ranged from 30.0±2.3 to 64.6±11.7 mg/kg Pb, 78.4±18.4 to 265.6±63.2 mg/kg Zn, and 0.8±0.13 to 1.40±0.16 mg/kg Cd. Total trace metal levels in soil decreased rapidly with distance from the road. Total Pb decreased with distance up to 30 m from the road, where it reached a background soil concentration of 28 mg/kg dry weight. The study found background values of 50 and 1.4 mg/kg for Zn and Cd in roadside soils, respectively. Similarly, Pb concentration in Amaranthus dubius leaves decreased with increasing distance from the road edge. The dominant pathway for Pb contamination was from atmospheric deposition, which was consistent with Pb concentrations in surface films. The mean Pb concentrations in leaves of roadside crops were higher than those in their respective roots, with the highest leaf-to-root ratio observed in the Brassica oleraceae acephala group. The lowest Pb and Zn concentrations were found in the fruit compared to the leaves of the same crops. Leaves of roadside vegetables were therefore considered a potential source of heavy metal contamination to farmers and consumers in urban areas. It is recommended that leafy vegetables should be grown 30 m from roads in high-traffic, urban areas

  17. Determination of Optimum Sanitizer Levels for Prevention of Salmonella Cross-Contamination of Mature Round Tomatoes in a Laboratory Model Flume System.

    Science.gov (United States)

    Sreedharan, Aswathy; Li, You; De, Jaysankar; Gutierrez, Alan; Silverberg, Rachael; Schneider, Keith R

    2017-09-01

    Salmonella has been reported to be involved in several foodborne illness outbreaks, many of which resulted from consumption of raw tomatoes. This research aimed to optimize and evaluate the concentration of free chlorine (hypochlorous acid [HOCl]) used as a sanitizer to prevent cross-contamination of tomatoes inoculated with a cocktail of five rifampin-resistant Salmonella enterica serovars in a laboratory-based model flume system. Organic load, prepared using sterilized Scotts Premium Topsoil, was added in different quantities to the flume wash water to simulate real-world packinghouse conditions. In a typical packinghouse operation utilizing a recirculating flume system, the organic matter washed from tomato surfaces accumulates over time. In this study, different concentrations (0, 25, 50, 75, and 100 ppm) of HOCl were used as sanitizers under three organic load conditions (0, 650, and 1,000 mg/L chemical oxygen demand). Results showed that 100 ppm of HOCl was necessary to prevent Salmonella cross-contamination of uninoculated tomatoes in the model flume system in the presence of organic loading. Also, when treated with 100 ppm of HOCl, Salmonella levels were reduced by >4.5 log CFU per tomato from inoculated tomatoes in the presence of organic load. At 75 ppm of HOCl, Salmonella cross-contamination was prevented, but only in the absence of organic loading. In studies in which plate counts were negative, whole tomato enrichment studies were performed. No cross-contamination of uninoculated tomatoes was recorded when 100 ppm of HOCl was used, even in the presence of high organic load (1,000 mg/L chemical oxygen demand). Although sanitizer application reduces contamination on tomato surfaces, the primary function of sanitizers in the wash water is to prevent cross-contamination.

  18. The study of contamination of discharged runoff from surface water disposal channels of Bushehr city in 2012-2013

    Directory of Open Access Journals (Sweden)

    Vaheid Noroozi-Karbasdehi

    2016-09-01

    Full Text Available Background: In coastal cities, wastewater discharge into the sea is one of the options for sewage disposal that in case of non-compliance with health standards  in wastewater disposal will be led to the spread of infection and disease. On the other hand, water resources preservation and using them efficiently are the principles of sustainable development of each country. This study was aimed to investigate the contamination of discharged runoff from the surface water disposal channels of Bushehr city in 2012 - 13. Materials and Methods: In this study, Sampling was conducted by composite sampling method from output of the five main surface water disposal channels leading to the Persian Gulf located in the coastal region of Bushehr city during two seasons including wet (winter and dry (summer in 2012- 13. Then, experimental tests of BOD5, total coliform and fecal coliform were done on any of the 96 samples according to the standard method. Results: Analysis of the data showed that the BOD5, total coliform and fecal coliform of effluent runoff of the channels were more than the national standard output of disposal wastewaters into the surface waters, and the highest and lowest amount of BOD5 which obtained were 160 mg/L and 28 mg/L, respectively. Conclusion: considering the fact that discharged runoff from surface water disposal channels link from shoreline to sea in close distance and they often are as natural swimming sites and even fishing sites of Bushehr city, and also according to high level of organic and bacterial load of these channels, it is urgently required to be considered by the authorities.

  19. Corticosterone levels in relation to trace element contamination along an urbanization gradient in the common blackbird (Turdus merula).

    Science.gov (United States)

    Meillère, Alizée; Brischoux, François; Bustamante, Paco; Michaud, Bruno; Parenteau, Charline; Marciau, Coline; Angelier, Frédéric

    2016-10-01

    In a rapidly urbanizing world, trace element pollution may represent a threat to human health and wildlife, and it is therefore crucial to assess both exposition levels and associated effects of trace element contamination on urban vertebrates. In this study, we investigated the impact of urbanization on trace element contamination and stress physiology in a wild bird species, the common blackbird (Turdus merula), along an urbanization gradient (from rural to moderately urbanized areas). Specifically, we described the contamination levels of blackbirds by 4 non-essential (Ag, Cd, Hg, Pb) and 9 essential trace elements (As, Co, Cr, Cu, Fe, Mn, Ni, Se, Zn), and explored the putative disrupting effects of the non-essential element contamination on corticosterone levels (a hormonal proxy for environmental challenges). We found that non-essential trace element burden (Cd and Pb specifically) increased with increasing urbanization, indicating a significant trace element contamination even in medium sized cities and suburban areas. Interestingly, the increased feather non-essential trace element concentrations were also associated with elevated feather corticosterone levels, suggesting that urbanization probably constrains birds and that this effect may be mediated by trace element contamination. Future experimental studies are now required to disentangle the influence of multiple urban-related constraints on corticosterone levels and to specifically test the influence of each of these trace elements on corticosterone secretion. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Improving Satellite Retrieved Infrared Sea Surface Temperatures in Aerosol-Contaminated Regions

    Science.gov (United States)

    Luo, B.; Minnett, P. J.; Szczodrak, G.; Kilpatrick, K. A.

    2017-12-01

    Infrared satellite observations of sea surface temperature (SST) have become essential for many applications in meteorology, climatology, and oceanography. Applications often require high accuracy SST data: for climate research and monitoring an absolute uncertainty of 0.1K and stability of better than 0.04K per decade are required. Tropospheric aerosol concentrations increase infrared signal attenuation and prevent the retrieval of accurate satellite SST. We compare satellite-derived skin SST with measurements from the Marine-Atmospheric Emitted Radiance Interferometer (M-AERI) deployed on ships during the Aerosols and Ocean Science Expeditions (AEROSE) and with quality-controlled drifter temperatures. After match-up with in-situ SST and filtering of cloud contaminated data, the results indicate that SST retrieved from MODIS (Moderate Resolution Imaging Spectroradiometer) aboard the Terra and Aqua satellites have negative (cool) biases compared to shipboard radiometric measurements. There is also a pronounced negative bias in the Saharan outflow area that can introduce SST errors >1 K at aerosol optical depths > 0.5. In this study, we present a new method to derive night-time Saharan Dust Index (SDI) algorithms based on simulated brightness temperatures at infrared wavelengths of 3.9, 10.8 and 12.0 μm, derived using RTTOV. We derived correction coefficients for Aqua MODIS measurements by regression of the SST errors against the SDI. The biases and standard deviations are reduced by 0.25K and 0.19K after the SDI correction. The goal of this study is to understand better the characteristics and physical mechanisms of aerosol effects on satellite retrieved infrared SST, as well as to derive empirical formulae for improved accuracies in aerosol-contaminated regions.

  1. A Complete Analytical Screening Identifies the Real Pesticide Contamination of Surface Waters

    Science.gov (United States)

    Moschet, Christoph; Wittmer, Irene; Simovic, Jelena; Junghans, Marion; Singer, Heinz; Stamm, Christian; Leu, Christian; Hollender, Juliane

    2014-05-01

    A comprehensive assessment of pesticides in surface waters is challenging due to the large number of potential contaminants. In Switzerland for example, roughly 500 active ingredients are registered as either plant protection agent (PPA) or as biocide. In addition, an unlimited number of transformations products (TPs) can enter or be formed in surfaced waters. Most scientific publications or regulatory monitoring authorities have implemented 15-40 pesticides in their analytics. Only a few TPs are normally included. Interpretations of the surface water quality based on these subsets remains error prone. In the presented study, we carried out a nearly complete analytical screening covering 86% of all polar organic pesticides (from agricultural and urban sources) in Switzerland (300 substances) and 134 TPs with limits of quantification in the low ng/L range. The comprehensive pesticide screening was conducted by liquid-chromatography coupled to high-resolution tandem mass spectrometry. Five medium-sized rivers (Strahler stream order 3-4, catchment size 35-105 km2), containing high percentiles of diverse crops, orchards and urban settlements in their catchments, were sampled from March till July 2012. Nine subsequent time-proportional bi-weekly composite samples were taken in order to quantify average concentrations. In total, 104 different active ingredients could be detected in at least one of the five rivers. Thereby, 82 substances were only registered as PPA, 20 were registered as PPA and as biocide and 2 were only registered as biocide. Within the PPAs, herbicides had the most frequent detections and the highest concentrations, followed by fungicides and insecticides. Most concentrations were found between 1 and 50 ng/L; however 31 substances (mainly herbicides) had concentrations above 100 ng/L and 3 herbicides above 1000 ng/L. It has to be noted that the measured concentrations are average concentrations over two weeks in medium sized streams and that maximum

  2. Current Contamination Status of Perfluoroalkyl Substances in Tapwater from 17 Cities in the Eastern China and Their Correlations with Surface Waters.

    Science.gov (United States)

    Tan, Ke-Yan; Lu, Guo-Hui; Piao, Hai-Tao; Chen, Shu; Jiao, Xing-Chun; Gai, Nan; Yamazaki, Eriko; Yamashita, Nobuyoshi; Pan, Jing; Yang, Yong-Liang

    2017-08-01

    The contamination status of perfluoroalkyl substances (PFASs) were investigated in 64 tapwater samples collected from 17 cities and 45 surface water samples from adjacent areas in the eastern China. The total PFAS concentrations in tapwater ranged from 1.4 to 175 ng/L; relatively higher PFAS levels were observed in samples collected from the Yangtze River Delta region, which was similar to the geographical distribution pattern of PFAS levels observed in rivers and lakes. The highest total PFASs in tapwater was found in Changshu, where several fluorine-related industries are located, whereas the lowest was observed in Beijing. Significant positive correlations between PFAS compositions in tap water sample and their source waters were noted. Several industries such as paper, textile, and leather industries may contribute to the contamination of PFASs in tapwater.

  3. Surface and borehole electromagnetic imaging of conducting contaminant plumes. 1997 annual progress report

    International Nuclear Information System (INIS)

    Berryman, J.G.

    1997-01-01

    'Electromagnetic induction tomography is a promising new tool for imaging electrical conductivity variations in the earth. The EM source field is produced by induction coil (magnetic dipole) transmitters deployed at the surface or in boreholes. Vertical and horizontal component magnetic field detectors are deployed in other boreholes or on the surface. Sources and receivers are typically deployed in a configuration surrounding the region of interest. The goal of this procedure is to image electrical conductivity variations in the earth, much as x-ray tomography is used to image density variations through cross-sections of the body. Although such EM field techniques have been developed and applied, the algorithms for inverting the magnetic data to produce the desired images of electrical conductivity have not kept pace. One of the main reasons for the lag in the algorithm development has been the fact that the magnetic induction problem is inherently three dimensional: other imaging methods such as x-ray and seismic can make use of two-dimensional approximations that are not too far from reality, but the author does not have this luxury in EM induction tomography. In addition, previous field experiments were conducted at controlled test sites that typically do not have much external noise or extensive surface clutter problems often associated with environmental sites. To use the same field techniques in environments more typical of cleanup sites requires a new set of data processing tools to remove the effects of both noise and clutter. The goal of this project is to join theory and experiment to produce enhanced images of electrically conducting fluids underground, allowing better localization of contaminants and improved planning strategies for the subsequent remediation efforts. After explaining the physical context in more detail, this report will summarize the progress made in the first year of this project: (1) on code development and (2) on field tests of

  4. Modeling the level of contamination of Staphylococcus aureus in ready-to-eat kimbab in Korea.

    Science.gov (United States)

    Bahk, Gyung-Jin; Hong, Chong-Hae; Oh, Deog-Hwan; Ha, Sang-Do; Park, Ki-Hwan; Todd, Ewen C D

    2006-06-01

    The risk of Staphylococcus aureus in ready-to-eat kimbab (rice rolled in laver) sold in Korea was evaluated by a mathematical modeling approach. Four nodes were constructed from preparation at retail to consumption. A predictive microbial growth model and survey data were combined with probabilistic modeling to simulate the level of S. aureus in a single kimbab at the time of consumption. We estimated the mean level of S. aureus to be 2.92 log CFU/g for a typical kimbab (150 to 200 g each) at the time of consumption. Our model also showed that 29.73% of the kimbabs had > or = 100,000 S. aureus CFU/g, which poses some risk of illness, since some level of enterotoxin would be expected from toxigenic strains. However, because of the lack of dose-response models for staphylococcal enterotoxin, the final level of S. aureus in the kimbabs could not be used to estimate how many people would become ill from eating them. Correlation sensitivity results showed that consumer eating patterns and initial contamination levels at retail stores were the most significant risk factors for illness and that temperature control under 10 degrees C was a critical control point in kimbab retail establishments to prevent the growth of S. aureus.

  5. Neurotoxic effects of low-level methylmercury contamination in the Amazonian basin

    Energy Technology Data Exchange (ETDEWEB)

    Lebel, J.; Mergler, D.; Lucotte, M.; Larribe, F.; Dolbec, J. [Univ. du Quebec, Montreal, Quebec (Canada); Branches, F. [Santarem, Para (Brazil); Amorim, M. [Univ. Federal do Para (Brazil). Cytogenetic Lab.

    1998-10-01

    Many studies have demonstrated mercury contamination in the Amazonian ecosystem, particularly in fish, a dietary mainstay of populations in this region. The present study focused on potential health effects of this low-level methylmercury exposure. The study was carried out in a village on the Tapajos River, a tributary of the Amazon, on 91 adults inhabitants whose hair mercury levels were inferior to 50 {micro}/g. Performance on a neurofunctional test battery and clinical manifestations of nervous system dysfunction were examined in relation to hair mercury concentrations. Near visual contrast sensitivity and manual dexterity, adjusted for age, decreased significantly with hair mercury levels (P < 0.05), while there was a tendency for muscular fatigue to increase and muscular strength to decrease in women. For the most part, clinical examinations were normal, however, hair mercury levels were significantly higher (P < 0.05) for persons who presented disorganized movements on an alternating movement task and for persons with restricted visual fields. These results suggest dose-dependent nervous system alterations at hair mercury levels below 50 {micro}g/g, previously considered a threshold for clinical effects. The profile of dysfunction in this adult population is consistent with the current knowledge on methylmercury poisoning. The long-term implications of these findings are unknown and need to be addressed.

  6. Assessment of contaminant levels and trophic relations at a World Heritage Site by measurements in a characteristic shorebird species

    Energy Technology Data Exchange (ETDEWEB)

    Schwemmer, Philipp, E-mail: schwemmer@ftz-west.uni-kiel.de [Research and Technology Centre (Forschungs- und Technologiezentrum), University of Kiel, Hafentörn 1, 25761 Büsum (Germany); Covaci, Adrian, E-mail: adrian.covaci@uantwerpen.be [Toxicological Center, University of Antwerp, Universiteitsplein 1, 2610 Wilrijk (Belgium); Das, Krishna, E-mail: krishna.das@ulg.ac.be [Laboratory for Oceanology-MARE Research Center, University of Liege, Allée de la Chimie 17, B6C, Institut de Chimie, 4000 Liege (Sart-Tilman) (Belgium); Lepoint, Gilles, E-mail: g.lepoint@ulg.ac.be [Laboratory for Oceanology-MARE Research Center, University of Liege, Allée de la Chimie 17, B6C, Institut de Chimie, 4000 Liege (Sart-Tilman) (Belgium); Adler, Sven, E-mail: sven.adler@slu.se [Swedish University of Agricultural Sciences, 901 83 Umeå (Sweden); Garthe, Stefan, E-mail: garthe@ftz-west.uni-kiel.de [Research and Technology Centre (Forschungs- und Technologiezentrum), University of Kiel, Hafentörn 1, 25761 Büsum (Germany)

    2015-01-15

    The River Elbe is responsible for influxes of contaminants into the Wadden Sea World Heritage Site. We investigated levels of polychlorinated biphenyls (PCBs), oxychlordane (OxC), hexachlorobenzene (HCB), hexachlorocyclohexanes (α-, β-, γ-HCHs), dichlorodiphenyltrichloroethane (DDT) and its metabolites, and polybrominated diphenyl ethers (PBDEs) in blood and feathers from Eurasian oystercatchers (Haematopus ostralegus; n=28) at the Elbe and compared it with a non-riverine site about 90 km further north. (1) Mean levels of all contaminants in feathers and serum were significantly higher at the river (∑PCBs: 27.6 ng/g feather, 37.0 ng/ml serum; ∑DDTs: 5.3 ng/g feather, 4.4 ng/ml serum) compared with the non-riverine site (∑PCBs: 6.5 ng/g feather, 1.2 ng/ml serum; ∑DDTs: 1.4 ng/g feather, 0.5 ng/ml serum). Mean ∑HCH and HCB levels were <1.8 ng/g in feather and <1.8 ng/ml in serum at both sites. (2) Levels of most detectable compounds in serum and feathers were significantly related, but levels were not consistently higher in either tissue. (3) There was no significant relationship between trophic level in individual oystercatchers (expressed as δ15N) or the degree of terrestrial feeding (expressed as δ13C) and contaminant loads. (4) PBDEs were not detected in significant amounts at either site. The results of this study indicate that the outflow from one of Europe′s largest river systems is associated with significant historical contamination, reflected by the accumulation of contaminants in body tissues in a coastal benthivore predator. - Highlights: • Contaminants in Oystercatchers from the Elbe river and a non-riverine site were measured. • Mean levels of contaminants were higher at the river than at the non-riverine site. • Levels of most contaminants in serum and feathers were significantly related. • No relationship between trophic level (δ15N) and contaminant level was found. • One of Europe′s largest river systems is associated

  7. An integrated model for assessing the risk of TCE groundwater contamination to human receptors and surface water ecosystems

    DEFF Research Database (Denmark)

    McKnight, Ursula S.; Funder, S.G.; Rasmussen, J.J.

    2010-01-01

    The practical implementation of the European Water Framework Directive has resulted in an increased focus on the hyporheic zone. In this paper, an integrated model was developed for evaluating the impact of point sources in groundwater on human health and surface water ecosystems....... An ecological risk assessment found that the TCE contamination did not impact the stream ecosystem. Uncertainty assessment revealed hydraulic conductivity to be the most important site-specific parameter. These results indicate that contaminant plumes with μgL-1 concentrations of TCE entering surface water....... This was accomplished by coupling the system dynamics-based decision support system CARO-PLUS to the aquatic ecosystem model AQUATOX using an analytical volatilization model for the stream. The model was applied to a case study where a TCE contaminated groundwater plume is discharging to a stream. The TCE source...

  8. Laboratory Rodent Diets Contain Toxic Levels of Environmental Contaminants: Implications for Regulatory Tests.

    Directory of Open Access Journals (Sweden)

    Robin Mesnage

    Full Text Available The quality of diets in rodent feeding trials is crucial. We describe the contamination with environmental pollutants of 13 laboratory rodent diets from 5 continents. Measurements were performed using accredited methodologies. All diets were contaminated with pesticides (1-6 out of 262 measured, heavy metals (2-3 out of 4, mostly lead and cadmium, PCDD/Fs (1-13 out of 17 and PCBs (5-15 out of 18. Out of 22 GMOs tested for, Roundup-tolerant GMOs were the most frequently detected, constituting up to 48% of the diet. The main pesticide detected was Roundup, with residues of glyphosate and AMPA in 9 of the 13 diets, up to 370 ppb. The levels correlated with the amount of Roundup-tolerant GMOs. Toxic effects of these pollutants on liver, neurodevelopment, and reproduction are documented. The sum of the hazard quotients of the pollutants in the diets (an estimator of risk with a threshold of 1 varied from 15.8 to 40.5. Thus the chronic consumption of these diets can be considered at risk. Efforts toward safer diets will improve the reliability of toxicity tests in biomedical research and regulatory toxicology.

  9. Classification of Partial Discharge Measured under Different Levels of Noise Contamination.

    Directory of Open Access Journals (Sweden)

    Wong Jee Keen Raymond

    Full Text Available Cable joint insulation breakdown may cause a huge loss to power companies. Therefore, it is vital to diagnose the insulation quality to detect early signs of insulation failure. It is well known that there is a correlation between Partial discharge (PD and the insulation quality. Although many works have been done on PD pattern recognition, it is usually performed in a noise free environment. Also, works on PD pattern recognition in actual cable joint are less likely to be found in literature. Therefore, in this work, classifications of actual cable joint defect types from partial discharge data contaminated by noise were performed. Five cross-linked polyethylene (XLPE cable joints with artificially created defects were prepared based on the defects commonly encountered on site. Three different types of input feature were extracted from the PD pattern under artificially created noisy environment. These include statistical features, fractal features and principal component analysis (PCA features. These input features were used to train the classifiers to classify each PD defect types. Classifications were performed using three different artificial intelligence classifiers, which include Artificial Neural Networks (ANN, Adaptive Neuro-Fuzzy Inference System (ANFIS and Support Vector Machine (SVM. It was found that the classification accuracy decreases with higher noise level but PCA features used in SVM and ANN showed the strongest tolerance against noise contamination.

  10. Control levels for residual contamination in materials considered for recycle and reuse

    International Nuclear Information System (INIS)

    Hill, R.L.; Aaberg, R.L.; Baker, D.A.; Kennedy, W.E. Jr.

    1993-09-01

    Pacific Northwest Laboratory (PNL) is collecting data and conducting technical analyses to support joint efforts by the U.S. Department of Energy (DOE), Office of Environmental Guidance, Air, Water and Radiation Division (DOE/EH-232); by the U.S. Environmental Protection Agency (EPA); and by the U.S. Nuclear Regulatory Commission (NRC) to develop radiological control criteria for the recycle and reuse of scrap materials and equipment that contain residual radioactive contamination. The initial radiological control levels are the concentrations in or on materials considered for recycle or reuse that meet the individual (human) or industrial (electronics/film) dose criteria. The analysis identifies relevant radionuclides, potential mechanisms of exposure, and methods to determine possible non-health-related impacts from residual radioactive contamination in materials considered for recycle or reuse. The generic methodology and scenarios described here provide a basic framework for numerically deriving radiological control criteria for recycle or reuse. These will be adequately conservative for most situations

  11. POLYCYCLIC AROMATIC HYDROCARBON CONTAMINATION LEVELS IN COLLECTED SAMPLES FROM VICINITY OF A HIGHWAY

    Directory of Open Access Journals (Sweden)

    S. V. Samimi ، R. Akbari Rad ، F. Ghanizadeh

    2009-01-01

    Full Text Available Tehran as the biggest city of Iran with a population of more than 10 millions has potentially high pollutant exposures of gas oil and gasoline combustion from vehicles that are commuting in the highways every day. The vehicle exhausts contain polycyclic aromatic hydrocarbons, which are produced by incomplete combustion and can be directly deposited in the environment. In the present study, the presence of polycyclic aromatic hydrocarbons contamination in the collected samples of a western highway in Tehran was investigated. The studied location was a busy highway in Tehran. High performance liquid chromatography equipped with florescence detector was used for determination of polycyclic aromatic hydrocarbons concentrations in the studied samples. Total concentration of the ten studied polycyclic aromatic hydrocarbons compounds ranged from 11107 to 24342 ng/g dry weight in the dust samples and increased from 164 to 2886 ng/g dry weight in the soil samples taken from 300 m and middle of the highway, respectively. Also the average of Σ PAHs was 1759 ng/L in the water samples of pools in parks near the highway. The obtained results indicated that polycyclic aromatic hydrocarbons contamination levels were very high in the vicinity of the highway.

  12. Clean-up levels for recovery of a 137Cs contaminated site in the Slovak Republic

    International Nuclear Information System (INIS)

    Slavik, O.; Moravek, J.

    2003-01-01

    The 19 km long banks of the Bohunice NPP waste water recipient (Manivier canal (0.3 m 3 /s) and Dudvah River (0.8 m 3 /s)) has been identified as contaminated by 137 Cs as a result of two accidents on the CO 2 cooled and heavy water moderated NPP-A1 unit in 1976 and 1977. Until 1992, NPP waste water had been derived through a 5 km-long canal to the Dudvah River (Q a 1.8 m 3 /s) conducting with the Vah River (150 m 3 /s) after 13 km downstream at 90 km from Vah's mouth into the Danube River. Between 1976 and 1978, when both accidents happened, construction of a flood control project on Dudvah River had just been being implemented in the length of 8 km upstream of its mouth. In the next upstream part of the River with about 5 km long river section, affected by NPP, the flood control conditions are insufficient and has, hitherto, caused permanent concern of the public. In this paper authors deals with the radiological characterization of the contaminated banks, re-consideration of the restoration project, criteria dose assessments and cleanup level developments, as well as present conditions for implementation of planned bank restoration

  13. Allowable residual contamination levels of radionuclides in soil from pathway analysis

    International Nuclear Information System (INIS)

    Nyquist, J.E.; Baes, C.F. III.

    1987-01-01

    The uncertainty regarding radionuclide distributions among Remedial Action Program (RAP) sites and long-term decommissioning and closure options for these sites requires a flexible approach capable of handling different levels of contamination, dose limits, and closure scenarios. We identified a commercially available pathway analysis model, DECOM, which had been used previously in support of remedial activities involving contaminated soil at the Savannah River Plant. The DECOM computer code, which estimates concentrations of radionuclides uniformly distributed in soil that correspond to an annual effective dose equivalent, is written in BASIC and runs on an IBM PC or compatible microcomputer. We obtained the latest version of DECOM and modified it to make it more user friendly and applicable to the Oak Ridge National Laboratory (ORNL) RAP. Some modifications involved changes in default parameters or changes in models based on approaches used by the EPA in regulating remedial actions for hazardous substances. We created a version of DECOM as a LOTUS spreadsheet, using the same models as the BASIC version of DECOM. We discuss the specific modeling approaches taken, the regulatory framework that guided our efforts, the strengths and limitations of each approach, and areas for improvement. We also demonstrate how the LOTUS version of DECOM can be applied to specific problems that may be encountered during ORNL RAP activities. 18 refs., 2 figs., 3 tabs

  14. Bacterial Contamination of Clothes and Environmental Items in a Third-Level Hospital in Colombia

    Directory of Open Access Journals (Sweden)

    J. C. Cataño

    2012-01-01

    Full Text Available Objective. This study evaluates the bacterial contamination rate of items in the hospital setting that are in frequent contact with patients and/or physicians. By determining the bacterial species and the associated antibiotic resistance that patients are exposed to. Methods. Hospital-based cross-sectional surveillance study of potential bacterial reservoirs. Cultures from 30 computer keyboards, 32 curtains, 40 cell phones, 35 white coats, and 22 ties were obtained. Setting. The study was conducted an urban academic 650-bed teaching hospital providing tertiary care to the city of Medellin, Colombia. Results. In total, 235 bacterial isolates were obtained from 159 surfaces sampled. 98.7% of the surfaces grew positive bacterial cultures with some interesting resistance profiles. Conclusion. There are significant opportunities to reduce patient exposure to frequently pathogenic bacteria in the hospital setting; patients are likely exposed to many bacteria through direct contact with white coats, curtains, and ties. They may be exposed to additional bacterial reservoirs indirectly through the hands of clinicians, using computer keyboards and cell phones.

  15. Advancement of the arc-waterjet cutting to a gouging process for contaminated surface activity of steel components

    International Nuclear Information System (INIS)

    Bach, F.W.; Bruening, D.

    1990-01-01

    The technique of arc-waterjet cutting had to be progressed so that it is possible to gouge the surface of metallic components of nuclear power plants. With applicable cutting parameters depending on the thickness of the contamination the surface had to be gouged and converted to a granulation that is to remove. A continously pulled out wire electrode strikes an arc to the workpeace by short circuit and melts both. A concentric around the wire placed waterjet is able to wash the liquid metal away. With a computer numeric control it is possible to remove the surface of metal up to a deep penetration of 4 to 5 mm. With arc waterjet gouging a remote-controlled removal of contaminated surface activity in shutdowned nuclear power plants under water is possible. (orig./HP) With 15 refs., 1 tab., 14 figs [de

  16. Evaluation of hydrogen and oxygen impurity levels on silicon surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Kenny, M.J.; Wielunski, L.S.; Netterfield, R.P.; Martin, P.J.; Leistner, A. [Commonwealth Scientific and Industrial Research Organisation (CSIRO), Lindfield, NSW (Australia). Div. of Applied Physics

    1996-12-31

    This paper reports on surface analytical techniques used to quantify surface concentrations of impurities such as oxygen and hydrogen. The following analytical techniques were used: Rutherford and Backscattering, elastic recoil detection, time-of-flight SIMS, spectroscopic ellipsometry, x-ray photoelectron spectroscopy. The results have shown a spread in thickness of oxide layer, ranging from unmeasurable to 1.6 nm. The data must be considered as preliminary at this stage, but give some insight into the suitability of the techniques and a general idea of the significance of impurities at the monolayer level. These measurements have been carried out on a small number of silicon surfaces both semiconductor grade <111> crystalline material and silicon which has been used in sphere fabrication. 5 refs., 1 fig.

  17. Listeria monocytogenes contamination of the environment and surfaces of the equipment in the meat processing facilities in republic of Macedonia

    OpenAIRE

    Dean Jankuloski; Pavle Sekulovski; Risto Prodanov; Zehra Hajrulai Musliu; Biljana Stojanovska Dimzovska

    2007-01-01

    Listeria monocytogenes contamination of the environment and surfaces of the equipment was examined in seven meat processing facilities. Up to date prevalence of this foodborn pathogen in meat processing facilities facilities in Republic of Macedonia was unknown. Biofilms are composed from food spoilage microorganisms and food born pathogens. They are located on the surfaces of the equipment that come in contact with food and in facilities environment. Microorganisms in biofilm presenting micr...

  18. Cold plasma rapid decontamination of food contact surfaces contaminated with Salmonella and Escherichia coli 0157:H7

    Science.gov (United States)

    Cross-contamination of fresh produce from persistent pathogen reservoirs is a known risk factor in processing environments. Industry requires a waterless, zero-contact, chemical-free method for removing pathogens from food-contact surfaces. Cold plasma was tested for its ability to remove biofilms f...

  19. MECHANISTIC STUDIES OF SURFACE CATALYZED H2O2 DECOMPOSITION AND CONTAMINANT DEGRADATION IN THE PRESENCE OF SAND. (R823402)

    Science.gov (United States)

    This study examined the mechanism and kinetics of surface catalyzed hydrogen peroxide decomposition and degradation of contaminants in the presence of sand collected from an aquifer and a riverbed. Batch experiments were conducted using variable sand concentrations (0.2 to 1.0&nb...

  20. Bacterial communities of surface and deep hydrocarbon-contaminated waters of the Deepwater Horizon oil spill

    Science.gov (United States)

    Yang, T.; Nigro, L. M.; McKay, L.; Ziervogel, K.; Gutierrez, T.; Teske, A.

    2010-12-01

    We performed a 16S rRNA gene sequencing survey of bacterial communities within oil-contaminated surface water, deep hydrocarbon plume water, and deep water samples above and below the plume to determine spatial and temporal patterns of oil-degrading bacteria growing in response to the Deepwater Horizon oil leak. In addition, we are reporting 16S rRNA sequencing results from time series incubation, enrichment and cultivation experiments. Surface oil slick samples were collected 3 nautical miles from ground zero, (5/6/10, RV Pelican) and were added to uncontaminated surface water (collected within a 30 nautical mile radius of ground zero, 5/6/10 - 5/9/10, RV Pelican). This mixture was incubated for 20 days in a rolling bottle at 25°C. 16S rRNA clone libraries from marine snow-like microbial flocs that had formed during the incubation yielded a highly diverse bacterial community, predominately composed of the Alpha- and Gammaproteobacteria, and a smaller number of Planktomycetes and other bacterial lineages. The most frequently recovered proteobacterial sequences were closely related to cultured species of the genus Cycloclasticus, specialists in aerobic oxidation of aromatic hydrocarbons. These time series incubation results will be compared to the microbial community structure of contaminated surface water, sampled on the same cruise with RV Pelican (5/6/10-5/9/10) and frozen immediately. Stable isotope probing (SIP) experiments with C13-labelled alkanes and polycyclic aromatic substrates and gulf water samples have yielded different enrichments. With naphthalene, predominantly Alteromonas-related clones and a smaller share of Cycloclasticus clones were recovered; phenanthrene yielded predominantly clones related to Cycloclasticus, and diverse other Gamma- and Alphaproteobacteria. Analyses of SIP experiments with hexadecane are in progress. The microbial community composition of the deep hydrocarbon plume was characterized using water column profile samples taken

  1. High-performance liquid chromatography of methotrexate for environmental monitoring of surface contamination in hospital departments and assessment of occupational exposure.

    Science.gov (United States)

    Floridia, L; Pietropaolo, A M; Tavazzani, M; Rubino, F M; Colombi, A

    1999-04-16

    preliminary results from a recent hospital case-study, assessing the contamination level of furniture and equipment in drug preparation areas. Spillage fractions as high as 5% of the employed mass (70-260 mg/day) are measured on the polythene-backed paper disposable hood cover sheet; traces of MTX in the microgram range can also be measured on floor surfaces, furniture and handles, even at a distance from the preparation hoods.

  2. Comparison of Two Surface Contamination Sampling Techniques Conducted for the Characterization of Two Pajarito Site Manhattan Project National Historic Park Properties

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, Tammy Ann [Montana Tech of the Univ. of Montana, Butte, MT (United States); Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-07-29

    Technical Area-18 (TA-18), also known as Pajarito Site, is located on Los Alamos National Laboratory property and has historic buildings that will be included in the Manhattan Project National Historic Park. Characterization studies of metal contamination were needed in two of the four buildings that are on the historic registry in this area, a “battleship” bunker building (TA-18-0002) and the Pond cabin (TA-18-0029). However, these two buildings have been exposed to the elements, are decades old, and have porous and rough surfaces (wood and concrete). Due to these conditions, it was questioned whether standard wipe sampling would be adequate to detect surface dust metal contamination in these buildings. Thus, micro-vacuum and surface wet wipe sampling techniques were performed side-by-side at both buildings and results were compared statistically. A two-tail paired t-test revealed that the micro-vacuum and wet wipe techniques were statistically different for both buildings. Further mathematical analysis revealed that the wet wipe technique picked up more metals from the surface than the microvacuum technique. Wet wipes revealed concentrations of beryllium and lead above internal housekeeping limits; however, using an yttrium normalization method with linear regression analysis between beryllium and yttrium revealed a correlation indicating that the beryllium levels were likely due to background and not operational contamination. PPE and administrative controls were implemented for National Park Service (NPS) and Department of Energy (DOE) tours as a result of this study. Overall, this study indicates that the micro-vacuum technique may not be an efficient technique to sample for metal dust contamination.

  3. Evaluating non-incinerative treatment of organically contaminated low level mixed waste

    International Nuclear Information System (INIS)

    Shuck, D.L.; Wade, J.F.

    1993-01-01

    This investigation examines the feasibility of using non-incinerator technologies effectively to treat organically contaminated mixed waste. If such a system is feasible now, it would be easier to license because it would avoid the stigma that incineration has in the publics' perception. As other DOE facilities face similar problems, this evaluation is expected to be of interest to both DOE and the attendees of WM'93. This investigation considered treatment to land disposal restriction (LDR) standards of 21 different low level mixed (LLM) waste streams covered by the Rocky Flats Federal Facilities Compliance Agreement (FFCA) agreement with the Environmental Protection Agency (EPA). Typically the hazardous components consists of organic solvent wastes and the radioactive component consists of uranic/transuranic wastes. Limited amounts of cyanide and lead wastes are also involved. The primary objective of this investigation was to identify the minimum number of non-thermal unit processes needed to effectively treat this collection of mixed waste streams

  4. Trace-level mercury removal from surface water

    International Nuclear Information System (INIS)

    Klasson, K.T.; Bostick, D.T.

    1998-01-01

    Many sorbents have been developed for the removal of mercury and heavy metals from waters; however, most of the data published thus far do not address the removal of mercury to the target levels represented in this project. The application to which these sorbents are targeted for use is the removal of mercury from microgram-per-liter levels to low nanogram-per-liter levels. Sorbents with thiouronium, thiol, amine, sulfur, and proprietary functional groups were selected for these studies. Mercury was successfully removed from surface water via adsorption onto Ionac SR-4 and Mersorb resins to levels below the target goal of 12 ng/L in batch studies. A thiol-based resin performed the best, indicating that over 200,000 volumes of water could be treated with one volume of resin. The cost of the resin is approximately $0.24 per 1,000 gal of water

  5. Surface drainage in leveled land: Implication of slope

    Directory of Open Access Journals (Sweden)

    Antoniony S. Winkler

    Full Text Available ABSTRACT In the lowlands of Rio Grande do Sul, land leveling is mostly carried out with no slope for the purpose of rice production. In this environment, soils with a low hydraulic conductivity are predominant owing to the presence of a practically impermeable B-horizon near the surface. Land leveling leads to soil accommodation resulting in the formation of depressions where water accumulates after heavy rainfalls, subsequently leading to problems with crops implanted in succession to rice, such as soybeans. The objective of this research was to quantify the areas and volumes of water accumulation in soil as a function of the slope of land leveling. Five typical leveled lowland areas were studied as a part of this research. The original areas presented slopes of 0, 0.20, 0.25, 0.28 and 0.40%, which were used to generate new digital elevation models with slopes between 0 and 0.5%. These newly generated digital models were used to map the depressions with surface water storage. In conclusion, land leveling with slopes higher than 0.1% is recommended to minimize problems with superficial water storage in rice fields.

  6. Sea level: measuring the bounding surfaces of the ocean.

    Science.gov (United States)

    Tamisiea, Mark E; Hughes, Chris W; Williams, Simon D P; Bingley, Richard M

    2014-09-28

    The practical need to understand sea level along the coasts, such as for safe navigation given the spatially variable tides, has resulted in tide gauge observations having the distinction of being some of the longest instrumental ocean records. Archives of these records, along with geological constraints, have allowed us to identify the century-scale rise in global sea level. Additional data sources, particularly satellite altimetry missions, have helped us to better identify the rates and causes of sea-level rise and the mechanisms leading to spatial variability in the observed rates. Analysis of all of the data reveals the need for long-term and stable observation systems to assess accurately the regional changes as well as to improve our ability to estimate future changes in sea level. While information from many scientific disciplines is needed to understand sea-level change, this review focuses on contributions from geodesy and the role of the ocean's bounding surfaces: the sea surface and the Earth's crust. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

  7. Sea level: measuring the bounding surfaces of the ocean

    Science.gov (United States)

    Tamisiea, Mark E.; Hughes, Chris W.; Williams, Simon D. P.; Bingley, Richard M.

    2014-01-01

    The practical need to understand sea level along the coasts, such as for safe navigation given the spatially variable tides, has resulted in tide gauge observations having the distinction of being some of the longest instrumental ocean records. Archives of these records, along with geological constraints, have allowed us to identify the century-scale rise in global sea level. Additional data sources, particularly satellite altimetry missions, have helped us to better identify the rates and causes of sea-level rise and the mechanisms leading to spatial variability in the observed rates. Analysis of all of the data reveals the need for long-term and stable observation systems to assess accurately the regional changes as well as to improve our ability to estimate future changes in sea level. While information from many scientific disciplines is needed to understand sea-level change, this review focuses on contributions from geodesy and the role of the ocean's bounding surfaces: the sea surface and the Earth's crust. PMID:25157196

  8. Ground-penetrating radar (GPR) responses for sub-surface salt contamination and solid waste: modeling and controlled lysimeter studies.

    Science.gov (United States)

    Wijewardana, Y N S; Shilpadi, A T; Mowjood, M I M; Kawamoto, K; Galagedara, L W

    2017-02-01

    The assessment of polluted areas and municipal solid waste (MSW) sites using non-destructive geophysical methods is timely and much needed in the field of environmental monitoring and management. The objectives of this study are (i) to evaluate the ground-penetrating radar (GPR) wave responses as a result of different electrical conductivity (EC) in groundwater and (ii) to conduct MSW stratification using a controlled lysimeter and modeling approach. A GPR wave simulation was carried out using GprMax2D software, and the field test was done on two lysimeters that were filled with sand (Lysimeter-1) and MSW (Lysimeter-2). A Pulse EKKO-Pro GPR system with 200- and 500-MHz center frequency antennae was used to collect GPR field data. Amplitudes of GPR-reflected waves (sub-surface reflectors and water table) were studied under different EC levels injected to the water table. Modeling results revealed that the signal strength of the reflected wave decreases with increasing EC levels and the disappearance of the subsurface reflection and wave amplitude reaching zero at higher EC levels (when EC >0.28 S/m). Further, when the EC level was high, the plume thickness did not have a significant effect on the amplitude of the reflected wave. However, it was also found that reflected signal strength decreases with increasing plume thickness at a given EC level. 2D GPR profile images under wet conditions showed stratification of the waste layers and relative thickness, but it was difficult to resolve the waste layers under dry conditions. These results show that the GPR as a non-destructive method with a relatively larger sample volume can be used to identify highly polluted areas with inorganic contaminants in groundwater and waste stratification. The current methods of MSW dumpsite investigation are tedious, destructive, time consuming, costly, and provide only point-scale measurements. However, further research is needed to verify the results under heterogeneous aquifer

  9. Microplastic pollution in the Greenland Sea: Background levels and selective contamination of planktivorous diving seabirds.

    Science.gov (United States)

    Amélineau, F; Bonnet, D; Heitz, O; Mortreux, V; Harding, A M A; Karnovsky, N; Walkusz, W; Fort, J; Grémillet, D

    2016-12-01

    Microplastics have been reported everywhere around the globe. With very limited human activities, the Arctic is distant from major sources of microplastics. However, microplastic ingestions have been found in several Arctic marine predators, confirming their presence in this region. Nonetheless, existing information for this area remains scarce, thus there is an urgent need to quantify the contamination of Arctic marine waters. In this context, we studied microplastic abundance and composition within the zooplankton community off East Greenland. For the same area, we concurrently evaluated microplastic contamination of little auks (Alle alle), an Arctic seabird feeding on zooplankton while diving between 0 and 50 m. The study took place off East Greenland in July 2005 and 2014, under strongly contrasted sea-ice conditions. Among all samples, 97.2% of the debris found were filaments. Despite the remoteness of our study area, microplastic abundances were comparable to those of other oceans, with 0.99 ± 0.62 m -3 in the presence of sea-ice (2005), and 2.38 ± 1.11 m -3 in the nearby absence of sea-ice (2014). Microplastic rise between 2005 and 2014 might be linked to an increase in plastic production worldwide or to lower sea-ice extents in 2014, as sea-ice can represent a sink for microplastic particles, which are subsequently released to the water column upon melting. Crucially, all birds had eaten plastic filaments, and they collected high levels of microplastics compared to background levels with 9.99 and 8.99 pieces per chick meal in 2005 and 2014, respectively. Importantly, we also demonstrated that little auks took more often light colored microplastics, rather than darker ones, strongly suggesting an active contamination with birds mistaking microplastics for their natural prey. Overall, our study stresses the great vulnerability of Arctic marine species to microplastic pollution in a warming Arctic, where sea-ice melting is expected to release vast

  10. Geomicrobiology of High Level Nuclear Waste-Contaminated Vadose Sediments at the Hanford Site, Washington State

    International Nuclear Information System (INIS)

    Fredrickson, Jim K.; Zachara, John M.; Balkwill, David L.; Kennedy, David W.; Li, Shu-Mei W.; Kostandarithes, Heather M.; Daly, Michael J.; Romine, Margaret F.; Brockman, Fred J.

    2004-01-01

    Sediments from a high-level nuclear waste plume were collected as part of investigations to evaluate the potential fate and migration of contaminants in the subsurface. The plume originated from a leak that occurred in 1962 from a waste tank consisting of high concentrations of alkali, nitrate, aluminate, Cr(VI), 137Cs, and 99Tc. Investigations were initiated to determine the distribution of viable microorganisms in the vadose sediment samples, probe the phylogeny of cultivated and uncultivated members, and evaluate the ability of the cultivated organisms to survive acute doses of ionizing radiation. The populations of viable aerobic heterotrophic bacteria were generally low, from below detection to ∼104 7 CFU g-1 but viable microorganisms were recovered from 11 of 16 samples including several of the most radioactive ones (e.g., > 10 ?Ci/g 137Cs). The isolates from the contaminated sediments and clone libraries from sediment DNA extracts were dominated by members related to known Gram-positive bacteria. Gram-positive bacteria most closely related to Arthrobacter species were the most common isolates among all samples but other high G+C phyla were also represented including Rhodococcus and Nocardia. Two isolates from the second most radioactive sample (>20 ?Ci 137Cs g-1) were closely related to Deinococcus radiodurans and were able to survive acute doses of ionizing radiation approaching 20kGy. Many of the Gram-positive isolates were resistant to lower levels of gamma radiation. These results demonstrate that Gram-positive bacteria, predominantly high G+C phyla, are indigenous to Hanford vadose sediments and some are effective at surviving the extreme physical and chemical stress associated with radioactive waste

  11. Heavy metals in the surface sediments of the northern portion of the South China Sea shelf: distribution, contamination, and sources.

    Science.gov (United States)

    Xu, Fangjian; Tian, Xu; Yin, Feng; Zhao, Yongfang; Yin, Xuebo

    2016-05-01

    The concentrations of seven heavy metals (Cr, Ni, Cu, Zn, As, Cd, and Pb) in the surface sediments of the northern portion of the South China Sea (SCS) shelf collected between 2012 and 2014 were measured to assess the potential contamination levels and determine the environmental risks that are associated with heavy metals in the area. The measured concentrations in the sediments were 12.4-72.5 mg kg(-1) for Cr, 4.4-29.2 mg kg(-1) for Ni, 7.1-38.1 mg kg(-1) for Cu, 19.3-92.5 mg kg(-1) for Zn, 1.3-12.1 mg kg(-1) for As, 0.03-0.24 mg kg(-1) for Cd, and 8.5-24.4 mg kg(-1) for Pb. These results indicate that the heavy metal concentrations in the sediments generally meet the China Marine Sediment Quality criteria and suggest that the overall sediment quality of the northern portion of the SCS shelf has not been significantly impacted by heavy metal pollution. However, the enrichment factor (EF) and geoaccumulation index (I geo) clearly show that elevated concentrations of Cd occur in the region. A Pearson's correlation analysis was performed, and the results suggest that Cr, Ni, Cu, and Zn have a natural origin; Cd is primarily sourced from anthropogenic activities, with partial lithogenic components, and As and Pb may be affected by factors such as varying input sources or pathways (i.e., coal burning activities and aerosol precipitation). Heavy metal contamination mostly occurred to the east of Hainan Island, mainly because of the rapid economic and social developments in the Hainan Island. The results of this study will be useful for marine environment managers for the remediation of pollution sources.

  12. Corticosterone levels in relation to trace element contamination along an urbanization gradient in the common blackbird (Turdus merula)

    OpenAIRE

    Meillère, Alizée; Brischoux, François; Bustamante, Paco; Michaud, Bruno; Parenteau, Charline; Marciau, Coline; Angelier, Frédéric

    2016-01-01

    International audience; In a rapidly urbanizing world, trace element pollution may represent a threat to human health and wildlife, and it is therefore crucial to assess both exposition levels and associated effects of trace element contamination on urban vertebrates. In this study, we investigated the impact of urbanization on trace element contamination and stress physiology in a wild bird species, the common blackbird (Turdus merula), along an urbanization gradient (from rural to moderatel...

  13. Surface radiological investigations of Trench 6 and low-level waste Line Leak Site 7. 4b at the Oak Ridge National Laboratory, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    Uziel, M.S.; Tiner, P.F.; Williams, J.K.

    1991-08-01

    A surface radiological investigation of Trench 6 and low-level radioactive waste (LLW) Line Leak Site 7.4b was conducted in July and August 1989 and January 1990 by the Measurement Applications and Development Group, Oak Ridge National Laboratory. The purposes of this survey were (1) to determine the presence, nature, and extent of surface radiological contamination and (2) to recommend interim corrective action to limit human exposures to radioactivity and minimize the potential for contaminant dispersion. Highest surface gamma levels encountered during the survey (39 mR/h) were found just south of the asphalt covering LLW Line Leak Site 7.4b. Elevated surface gamma levels (measuring 28 to 560 {mu}R/h) extended from this area to a width of 100 ft, westward 250 ft, and beyond the survey boundary. Beta-gamma levels up to 17 mrad/h measured on contact with the trunks of trees growing in the area southwest of Trench 6 suggest that three roots are reaching contamination deep within the ground. Since no gamma activity is associated with the trees or their leaves, the elevated beta levels are probably due to the uptake of residual {sup 90}Sr originating from the documented seepage at the Trench 6/Leak Site 7.4b area. Beta activity present in the leaf litter and surface soil indicate that decaying leaves are depositing measurable contaminants on the ground surface. Recommendations for corrective actions are included. 7 refs., 20 figs., 3 tabs.

  14. Effect of electrocardiographic contamination on surface electromyography assessment of back muscles.

    Science.gov (United States)

    Hu, Yong; Mak, Joseph N F; Luk, Keith D K

    2009-02-01

    The purpose of this study was to demonstrate the relative effect of electrocardiography (ECG) on back muscle surface electromyography (SEMG) parameters and their corresponding sensitivity in low back pain (LBP) assessment. Back muscle SEMG activities were recorded from 17 healthy subjects and 18 chronic LBP patients under static postures (straight sitting and upright standing), and dynamic action (flexion-extension). ECG cancellation based on independent component analysis (ICA) method was performed. Root mean square (RMS) and median frequency (MF) of raw and denoised SEMG data were computed respectively. Multiple comparisons were then performed. A consistent trend of change (increased MF and decreased RMS) followed ECG removal was noticed. In particular, in SEMG measurements under static postures, a significant decrease in RMS (pcorruption by ECG artifacts on SEMG measurements was found to be more serious and prominent in static postures than that in dynamic action. After ECG removal, significant improvements in the ability of SEMG to discriminate LBP patients from healthy subjects were seen in RMS amplitude recorded while standing (peffect of ECG contamination on back muscles SEMG parameters and LBP assessment.

  15. Strippable core-shell polymer emulsion for decontamination of radioactive surface contamination

    International Nuclear Information System (INIS)

    Hwang, Ho-Sang; Seo, Bum-Kyoung; Lee, Kune-Woo

    2011-01-01

    In this study, the core-shell composite polymer for decontamination from the surface contamination was synthesized by the method of emulsion polymerization and blends of polymers. The strippable polymer emulsion is composed of the poly(styrene-ethyl acrylate) [poly(St-EA)] composite polymer, poly(vinyl alcohol) (PVA) and polyvinylpyrrolidone (PVP). The morphology of the poly(St-EA) composite emulsion particle was core-shell structure, with polystyrene (PS) as the core and poly(ethyl acrylate) (PEA) as the shell. Core-shell polymers of styrene (St)/ethyl acrylate (EA) pair were prepared by sequential emulsion polymerization in the presence of sodium dodecyl sulfate (SDS) as an emulsifier using ammonium persulfate (APS) as an initiator. Related tests and analysis confirmed the success in synthesis of composite polymer. The products are characterized by FT-IR spectroscopy, TGA that were used, respectively, to show the structure, the thermal stability of the prepared polymer. Two-phase particles with a core-shell structure were obtained in experiments where the estimated glass transition temperature and the morphologies of emulsion particles. Decontamination factors of the strippable polymeric emulsion were evaluated with the polymer blend contents. (author)

  16. Monitoring of selected priority and emerging contaminants in the Guadalquivir River and other related surface waters in the province of Jaén, South East Spain.

    Science.gov (United States)

    Robles-Molina, José; Gilbert-López, Bienvenida; García-Reyes, Juan F; Molina-Díaz, Antonio

    2014-05-01

    The province of Jaén counts with four natural parks, numerous rivers, reservoirs and wetlands; moreover, it is probably the region with higher olive oil production in the world, which makes this zone a proper target to be studied based on the European Water Framework Directive 2000/60/CE. The aim of this survey is to monitor a total number of 373 compounds belonging to different families (pesticides, PAHs, nitrosamines, drugs of abuse, pharmaceuticals and life-style compounds) in surface waters located at different points of the province of Jaén. Among these compounds some priority organic substances (regulated by the EU Directive 2008/105/EC) and pollutants of emerging concern (not regulated yet) can be found. A liquid chromatography electrospray time-of-flight mass spectrometry (LC-TOFMS) method covering 340 compounds was developed and applied, together with a gas chromatography triple-quadrupole mass spectrometry (GC-MS/MS) method which enabled the analysis of 63 organic contaminants (30 of these compounds are analyzed by LC-TOFMS as well). From April 2009 to November 2010 a total of 83 surface water samples were collected (rivers, reservoirs and wetlands). In this period numerous organic contaminants were detected, most of them at the ng L(-1) level. The most frequently priority substances found were chlorpyrifos ethyl, diuron and hexachlorobenzene. Within the other groups, the most frequently detected compounds were: terbuthylazine, oxyfluorfen, desethyl terbuthylazine, diphenylamine (pesticide family); fluorene, phenanthrene, pyrene (PAHs group), codeine, paracetamol (pharmaceuticals compounds) and caffeine, nicotine (life-style compounds). As is could be expected, the total concentration of emerging contaminants is distinctly larger than that of priority pollutants, highlighting the importance of continuing with the study of their presence, fate and effects in aquatic environments. However, concentration levels (at the ng per liter level) are low in

  17. HYDROLASING OF CONTAMINATED UNDERWATER BASIN SURFACES AT THE HANFORD K AREA

    International Nuclear Information System (INIS)

    CHRONISTER, G.B.

    2005-01-01

    This paper discusses selecting and implementing hydrolasing technology to reduce radioactive contamination in preparing to dispose of the K Basins; two highly contaminated concrete basins at the Hanford Site. A large collection of spent nuclear fuel stored for many years underwater at the K Basins has been removed to stable, dry, safe storage. Remediation activities have begun for the remaining highly contaminated water. sludge, and concrete basin structures. Hydrolasing will be used to decontaminate and prepare the basin structures for disposal

  18. Do Contaminants Originating from State-of-the-Art Treated Wastewater Impact the Ecological Quality of Surface Waters?

    Science.gov (United States)

    Stalter, Daniel; Magdeburg, Axel; Quednow, Kristin; Botzat, Alexandra; Oehlmann, Jörg

    2013-01-01

    Since the 1980s, advances in wastewater treatment technology have led to considerably improved surface water quality in the urban areas of many high income countries. However, trace concentrations of organic wastewater-associated contaminants may still pose a key environmental hazard impairing the ecological quality of surface waters. To identify key impact factors, we analyzed the effects of a wide range of anthropogenic and environmental variables on the aquatic macroinvertebrate community. We assessed ecological water quality at 26 sampling sites in four urban German lowland river systems with a 0–100% load of state-of-the-art biological activated sludge treated wastewater. The chemical analysis suite comprised 12 organic contaminants (five phosphor organic flame retardants, two musk fragrances, bisphenol A, nonylphenol, octylphenol, diethyltoluamide, terbutryn), 16 polycyclic aromatic hydrocarbons, and 12 heavy metals. Non-metric multidimensional scaling identified organic contaminants that are mainly wastewater-associated (i.e., phosphor organic flame retardants, musk fragrances, and diethyltoluamide) as a major impact variable on macroinvertebrate species composition. The structural degradation of streams was also identified as a significant factor. Multiple linear regression models revealed a significant impact of organic contaminants on invertebrate populations, in particular on Ephemeroptera, Plecoptera, and Trichoptera species. Spearman rank correlation analyses confirmed wastewater-associated organic contaminants as the most significant variable negatively impacting the biodiversity of sensitive macroinvertebrate species. In addition to increased aquatic pollution with organic contaminants, a greater wastewater fraction was accompanied by a slight decrease in oxygen concentration and an increase in salinity. This study highlights the importance of reducing the wastewater-associated impact on surface waters. For aquatic ecosystems in urban areas this

  19. Declining metal levels at Foundry Cove (Hudson River, New York): Response to localized dredging of contaminated sediments

    International Nuclear Information System (INIS)

    Mackie, Joshua A.; Natali, Susan M.; Levinton, Jeffrey S.; Sanudo-Wilhelmy, Sergio A.

    2007-01-01

    This study examines the effectiveness of remediating a well-recognized case of heavy metal pollution at Foundry Cove (FC), Hudson River, New York. This tidal freshwater marsh was polluted with battery-factory wastes (1953-1979) and dredged in 1994-1995. Eight years after remediation, dissolved and particulate metals (Cd, Co, Cu, Pb, Ni, and Ag) were found to be lower than levels in the lower Hudson near New York City. Levels of metals (Co, Ni, Cd) on suspended particles were comparatively high. Concentrations of surface sediment Cd throughout the marsh system remain high, but have decreased both in the dredged and undredged areas: Cd was 2.4-230 mg/kg dw of sediment in 2005 vs. 109-1500 mg/kg in the same area in 1983. The rate of tidal export of Cd from FC has decreased by >300-fold, suggesting that dredging successfully stemmed a major source of Cd to the Hudson River. - Dredging of a hotspot of metal-contaminated sediment is associated with a recognizable local and river-wide decline in cadmium in the Hudson River, New York

  20. Building classification trees to explain the radioactive contamination levels of the plants; Construction d'arbres de discrimination pour expliquer les niveaux de contamination radioactive des vegetaux

    Energy Technology Data Exchange (ETDEWEB)

    Briand, B

    2008-04-15

    The objective of this thesis is the development of a method allowing the identification of factors leading to various radioactive contamination levels of the plants. The methodology suggested is based on the use of a radioecological transfer model of the radionuclides through the environment (A.S.T.R.A.L. computer code) and a classification-tree method. Particularly, to avoid the instability problems of classification trees and to preserve the tree structure, a node level stabilizing technique is used. Empirical comparisons are carried out between classification trees built by this method (called R.E.N. method) and those obtained by the C.A.R.T. method. A similarity measure is defined to compare the structure of two classification trees. This measure is used to study the stabilizing performance of the R.E.N. method. The methodology suggested is applied to a simplified contamination scenario. By the results obtained, we can identify the main variables responsible of the various radioactive contamination levels of four leafy-vegetables (lettuce, cabbage, spinach and leek). Some extracted rules from these classification trees can be usable in a post-accidental context. (author)

  1. Technical assessment of processes to enable recycling of low-level contaminated metal waste

    Energy Technology Data Exchange (ETDEWEB)

    Reimann, G.A.

    1991-10-01

    Accumulations of metal waste exhibiting low levels of radioactivity (LLCMW) have become a national burden, both financially and environmentally. Much of this metal could be considered as a resource. The Department of Energy was assigned the task of inventorying and classifying LLCMW, identifying potential applications, and applying and/or developing the technology necessary to enable recycling. One application for recycled LLCMW is high-quality canisters for permanent repository storage of high-level waste (HLW). As many as 80,000 canisters will be needed by 2035. Much of the technology needed to decontaminate LLCMW has already been developed, but no integrated process has been described, even on a pilot scale, for recycling LLCMW into HLW canisters. This report reviews practices for removal of radionuclides and for producing low carbon stainless steel. Contaminants that readily form oxides may be reduced to below de minimis levels and combined with a slag. Most of the radioactivity remaining in the ingot is concentrated in the inclusions. Radionuclides that chemically resemble the elements that comprise stainless steel can not be removed effectively. Slag compositions, current melting practices, and canister fabrication techniques were reviewed.

  2. Spatial variation of mercury levels in nesting Bonelli's eagles from Southwest Portugal: effects of diet composition and prey contamination

    International Nuclear Information System (INIS)

    Palma, Luis; Beja, Pedro; Tavares, Paula C.; Monteiro, Luis R.

    2005-01-01

    Mercury (Hg) was determined in adult Bonelli's eagles (Hieraaetus fasciatus) and their avian prey, from samples of feathers collected between 1992 and 2001 at the nesting sites of 21 pairs in Southwest Portugal. Eagle Hg levels showed great variation, reflecting primarily differences in diet composition and food chain biomagnification. Concentrations were positively correlated with the dietary proportion of insectivorous and omnivorous birds (e.g. egrets, corvids and thrushes), with very low levels for pairs feeding mainly on herbivores (e.g. rabbits, pigeons and partridges). Differences in prey contamination among breeding territories added to dietary effects in determining variation of Hg levels in eagles, shaping a spatial pattern that was largely consistent with a source of contamination in a coal-burning power-plant lying upwind of the study area. Despite this presumed contamination, Hg levels seemed to be of little concern to this eagle population, though there might be subtle deleterious effects on the reproductive output of a few pairs. This study emphasizes the need to account for dietary effects when biomonitoring Hg contamination using birds of prey. - The effects of diet composition and prey contamination added up to determine the spatial variation of Hg levels in breeding Bonelli's eagles

  3. Effect of surface carbon contamination on the chemical states of N-doped ZnO thin films

    Science.gov (United States)

    Zhang, Hong; Li, Wanjun; Qin, Guoping; Fang, Liang; Ruan, Haibo; Tan, Mi; Wu, Fang; Kong, Chunyang

    2018-02-01

    Nitrogen-doped ZnO thin films [ZnO:N] and intentional surface carbon-contaminated ZnO:N thin films [ZnO:N@C] were grown on quartz substrates by radio frequency magnetron sputtering deposition method. The structural, electrical and optical properties as well as chemical states of elements were investigated by means of X-ray diffraction (XRD), Hall effect measurement (Hall), UV-Vis-Near infrared spectrophotometer and X-ray photoelectron spectroscopy (XPS). The results indicate that surface carbon contamination almost does not affect the band gap of ZnO:N thin films but has a strong impact on the crystal quality of ZnO:N thin film surface and results in a significant increase in tensile stress. The XPS analysis shows that the effect of surface carbon contamination treatment on the chemical states of ZnO:N thin films is remarkable. Because the stability of Zn-N bonds in N-rich local environments is nowhere near that of those in O-rich local environments, the N atoms in N-rich local environments easily bond with surface carbon atoms to form undesirable C-N bonds, thus resulting in a decrease of NO acceptors in N-rich local environments. Obviously, it is unfavorable to subsequently prepare high stability of N-doped p-type ZnO thin films.

  4. Estuarine sediment resuspension and acidification: Release behaviour of contaminants under different oxidation levels and acid sources.

    Science.gov (United States)

    Martín-Torre, M Camino; Cifrian, Eva; Ruiz, Gema; Galán, Berta; Viguri, Javier R

    2017-09-01

    Carbon dioxide (CO 2 ) Capture and Storage (CCS) is a technology to reduce the emissions of this gas to the atmosphere by sequestering it in geological formations. In the case of offshore storage, unexpected CO 2 leakages will acidify the marine environment. Reductions of the pH might be also caused by anthropogenic activities or natural events such as acid spills and dredging operations or storms and floods. Changes in the pH of the marine environment will trigger the mobilisation of elements trapped in contaminated shallow sediments with unclear redox boundary. Trace element (As, Cd, Cr, Cu, Ni, Pb and Zn) release from anoxic and oxic estuarine sediment is analysed and modelled under different laboratory acidification conditions using HNO 3 (l) and CO 2 (g): acidification at pH = 6.5 as worst-case scenario in events of CO 2 leakages and acid spills, and acidification at pH = 7.0 as a seawater scenario under CO 2 leakages, acid spills, as well as sediment resuspension. The prediction of metal leaching behaviour appear to require sediment specific and site specific tools. In the present work it is demonstrated that the proposed three in-series reactions model predicts the process kinetics of the studied elements under different simulated environmental conditions (oxidation levels and acid sources). Differences between HNO 3 and CO 2 acidification are analysed through the influence of the CO 2 gas on the ionic competition of the medium. The acidification with CO 2 provokes higher released concentrations from the oxic sediment than from the anoxic sediment, except in the case of Zn, which influences the release of the other studied elements. Slight acidification can endanger the aquatic environment through an important mobilisation of contaminants. The obtained prediction of the contaminant release from sediment (kinetic parameters and maximum concentrations) can contribute to the exposure assessment stage for risk management and preincidental planning in

  5. Estimation and justification of permissible levels of Sr 90 in firewood and timber produced on the territories contaminated after the Chernobyl NPP accident

    International Nuclear Information System (INIS)

    Zabrodskij, V.N.; Bondar', Yu.I.; Sadchikov, V.I.; Kalinin, V.N.

    2014-01-01

    The permissible levels of Sr 90 in firewood and timber produced on the radioactively contaminated territory are calculated and justified. They are proposed to be used on the territories contaminated after the Chernobyl accident. (authors)

  6. 49 CFR 173.443 - Contamination control.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Contamination control. 173.443 Section 173.443... SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.443 Contamination control. (a) The level of non-fixed (removable) radioactive contamination on the external surfaces of each package offered for...

  7. Surface Tension Estimates for Droplet Formation in Slurries with Low Concentrations of Hydrophobic Particles, Polymer Flocculants or Surface-Active Contaminants

    Energy Technology Data Exchange (ETDEWEB)

    Gauglitz, Phillip A.; Mahoney, Lenna A.; Blanchard, Jeremy; Bamberger, Judith A.

    2011-06-10

    In support of the K-Basin project, Pacific Northwest National Laboratory (PNNL) was requested to evaluate the appropriate surface tension value to use in models predicting the formation of droplets from spray leaks of K-Basin slurries. The specific issue was whether it was more appropriate to use the surface tension of pure water in model predictions for all plausible spray leaks or to use a lower value. The surface tension of K-Basin slurries is potentially affected not only by particles but by low concentrations of nonionic polyacrylamide flocculant and perhaps by contaminants with surfactant properties, which could decrease the surface tension below that of water. A lower surface tension value typically results in smaller droplets being formed with a larger fraction of droplets in the respirable size range, so using the higher surface tension value of pure water is not conservative and thus needs a strong technical basis.

  8. Evaluation of ultrafiltration membranes for treating low-level radioactive contaminated liquid waste

    International Nuclear Information System (INIS)

    Koenst, J.W.; Roberts, R.C.

    1978-01-01

    A series of experiments were performed on Waste Disposal Facility (WD) influent using Romicon hollow fiber ultrafiltration modules with molecular weight cutoffs ranging from 2000 to 80,000. The rejection of conductivity was low in most cases. The rejection of radioactivity ranged from 90 to 98%, depending on the membrane type and on the feed concentration. Typical product activity ranged from 7 to 100 dis/min/ml of alpha radiation. Experiments were also performed on alpha-contaminated laundry wastewater. Results ranged from 98 to >99.8%, depending on the membrane type. This yielded a product concentration of less than 0.1 dis/min/ml of alpha radiation. Tests on PP-Building decontamination water yielded rejections of 85 to 88% alpha radiation depending on the membrane type. These experiments show that the ability to remove radioactivity by membrane is a function of the contents of the waste stream because the radioactivity in the wastewater is in various forms: ionic, polymeric, colloidal, and absorbed onto suspended solids. Although removal of suspended or colloidal material is very high, removal of ionic material is not as effective. Alpha-contaminated laundry wastewater proved to be the easiest to decontaminate, whereas the low-level PP-Building decontamination water proved to be the most difficult to decontaminate. Decontamination of the WD influent, a combined waste stream, varied considerably from day to day because of its constantly changing makeup. The WD influent was also treated with various substances, such as polyelectrolytes, complexing agents, and coagulants, to determine if these additives would aid in the removal of radioactive material from the various wastewaters by complexing the ionic species. At the present time, none of the additives evaluated has had much effect; but experiments are continuing

  9. Ab initio surface core-level shifts and surface segregation energies

    DEFF Research Database (Denmark)

    Aldén, Magnus; Skriver, Hans Lomholt; Johansson, Börje

    1993-01-01

    We have calculated the surface core-level energy shifts of the 4d and 5d transition metals by means of local-density theory and a Green’s-function technique based on the linear muffin-tin orbitals method. Final-state effects are included by treating the core-ionized atom as an impurity located...

  10. Insect Residue Contamination on Wing Leading Edge Surfaces: A Materials Investigation for Mitigation

    Science.gov (United States)

    Lorenzi, Tyler M.; Wohl, Christopher J.; Penner, Ronald K.; Smith, Joseph G.; Siochi, Emilie J.

    2011-01-01

    Flight tests have shown that residue from insect strikes on aircraft wing leading edge surfaces may induce localized transition of laminar to turbulent flow. The highest density of insect populations have been observed between ground level and 153 m during light winds (2.6 -- 5.1 m/s), high humidity, and temperatures from 21 -- 29 C. At a critical residue height, dependent on the airfoil and Reynolds number, boundary layer transition from laminar to turbulent results in increased drag and fuel consumption. Although this represents a minimal increase in fuel burn for conventional transport aircraft, future aircraft designs will rely on maintaining laminar flow across a larger portion of wing surfaces to reduce fuel burn during cruise. Thus, insect residue adhesion mitigation is most critical during takeoff and initial climb to maintain laminar flow in fuel-efficient aircraft configurations. Several exterior treatments investigated to mitigate insect residue buildup (e.g., paper, scrapers, surfactants, flexible surfaces) have shown potential; however, implementation has proven to be impractical. Current research is focused on evaluation of wing leading edge surface coatings that may reduce insect residue adhesion. Initial work under NASA's Environmentally Responsible Aviation Program focused on evaluation of several commercially available products (commercial off-the-shelf, COTS), polymers, and substituted alkoxy silanes that were applied to aluminum (Al) substrates. Surface energies of these coatings were determined from contact angle data and were correlated to residual insect excrescence on coated aluminum substrates using a custom-built "bug gun." Quantification of insect excrescence surface coverage was evaluated by a series of digital photographic image processing techniques.

  11. An automated alpha scanner for estimating plutonium contamination levels on FBTR fuel pin

    International Nuclear Information System (INIS)

    Bagul, D.G.; Sharma, V.P.; Benadikar, S.V.; Karnani, N.K.; Kamath, K.V.

    1995-01-01

    An automated alpha scanner has been developed for estimating plutonium contamination on SS clad fuel pins fabricated in Radiometallurgy Division for Fast Breeder Test Reactor (FBTR). The unit can detect as low as 1% of the allowed contamination limit for the fuel pin. Because of automation, large number of pins can be systematically scanned for Pu contamination with minimum radiation exposure to the operator. (author). 3 refs., 1 fig., 1 tab

  12. Matrix elements for level shifts and widths of hydrogenic levels in ion-surface interactions

    Energy Technology Data Exchange (ETDEWEB)

    Thumm, U.; Kuerpick, P.

    1996-05-01

    The authors present a derivation of basic one-electron matrix elements involved in the ion-metal surface scattering theory. Their method allows for the convenient generation of matrix elements for high principal quantum numbers of the projectile states and thus provides basic building blocks for the ab-initio description of highly charged ion-surface interactions. The matrix elements related to the energy shifts can be evaluated for an arbitrary one-dimensional potential therefore allowing the inclusion of electronic and nuclear self-image potentials. The authors extend these concepts to wave functions generated from an arbitrary one-dimensional surface potential and show applications to various surface potentials, projectile nuclear charges and hydrogenic levels.

  13. Assessment of Microbial Contamination of Surfaces and Medical Equipment in Wards of the Panjom Azar Hospital of Gorgan in 2014

    Directory of Open Access Journals (Sweden)

    Roghaye Noroozi

    2014-06-01

    Full Text Available Methods: In this cross-sectional study, different wards of panjom Azar educational hospital including ICU, dialysis and surgery room were investigated. Samples were collected randomly, for three months from July to September 2014, from beds, oxygen masks, oxygen manometer, patient table, covers of the patient's medical records, nurse's desk, border walls and water tap.  Samples were then cultured on blood agar and EMB agar. In order to determine the bacteria type, specific culture media with specific biochemical tests and diagnostic disks were used. Results: Results showed that from 216 samples collected from the levels, the 190 cases (88% had microbial contamination. Most of the recognized bacteria were Staphylococcus saprophyticus, Staphylococcus epidermidis, Staphylococcus aureus, Bacillus subtilis, Pseudomonas aeruginosa, Escherichia coli, Enterobacter and klebsiela. Results of microbial culture of equipments and levels were positive in case of bacterial contamination and maximum contamination was observed in the dialysis ward of the hospital. Conclusion: Due to the relatively high detected contamination, contamination control of levels and patient care equipments could considered as an effective action in reducing nosocomial infections. Thus, using appropriate disinfectant equipment, monitoring the disinfectants preparation, continuous monitoring and detection of common microorganisms are the most important ways for infection control in hospitals.

  14. Assessment of PCDD/Fs levels in soil at a contaminated sawmill site in Sweden--a GIS and PCA approach to interpret the contamination pattern and distribution.

    Science.gov (United States)

    Henriksson, S; Hagberg, J; Bäckström, M; Persson, I; Lindström, G

    2013-09-01

    Polychlorinated dibenzo-p-dioxins and polychlorinated dibenzo-p-furans (PCDD/Fs) were analysed in soil from a Swedish sawmill site where chlorophenols (CPs) had been used more than 40 years ago. The most contaminated area at the site was the preservation subarea where the PCDD/F WHO2005-TEQ level was 3450 times higher than the current Swedish guideline value of 200 ng TEQ/kg soil for land for industrial use. It was also shown that a fire which destroyed the sawmill might have affected the congener distribution at the concerned areas. To get a broader picture of the contamination both GIS (spatial interpolation analysis) and multivariate data analysis (PCA) were applied to visualize and compare PCDD/F levels as well as congener distributions at different areas at the site. It is shown that GIS and PCA are powerful tools in decisions on future investigations, risk assessments and remediation of contaminated sites. Copyright © 2013 Elsevier Ltd. All rights reserved.

  15. Carryover of maduramicin from feed containing cross-contamination levels into eggs of laying hens.

    Science.gov (United States)

    Bodi, Dorina; Fry, Hildburg; Schafft, Helmut; Lahrssen-Wiederholt, Monika; Preiss-Weigert, Angelika

    2012-07-18

    Maduramicin is a coccidiostat authorized as feed additive in the European Union for chickens and turkeys for fattening but not for laying hens, considering the risk of residues in eggs. The unavoidable cross-contamination of non-target feed with coccidiostats is regulated by Commission Directive 2009/8/EC and resulting carry-over in food by Commission Regulation (EC) No. 124/2009. To verify the compliance of the maximum levels for maduramicin in feed (50 μg/kg) and eggs (2 μg/kg), the carry-over from feed into eggs was investigated. Diets containing 10, 30, and 50 μg of maduramicin/kg of feed were fed to laying hens. Feed, egg white, and yolk were analyzed by LC-MS/MS. Maduramicin residues were only detected in in egg yolk. Feeding the 10 μg/kg maduramicin diet resulted in maduramicin concentrations up to 2.5 μg/kg in whole eggs, already exceeding the maximum level. A carry-over rate of 8% maduramicin from feed into eggs was calculated.

  16. A dynamic compartment mode for evaluating the contamination level of tritium in agricultural plants

    Energy Technology Data Exchange (ETDEWEB)

    Keum, Dong Kwon; Lee, Han Soo; Kang, Hee Seok; Jun, In; Choi, Yong Ho; Lee, Chang Woo

    2006-03-15

    This report describes a dynamic compartment model for evaluating the tritium level in agricultural plants after a short-term exposure to HTO vapor and its comparison with experimental results to test the predictive accuracy of the model. The model uses a time-dependent growth equation of a plant so that it can predict the contamination level of tritium depending on the stage of the growth of the plant, which is a major difference from some other compartment models using a constant crop yield. The model is able to calculate the time variable concentrations of the compartments representing the atmosphere, soil, and plants of four categories including leafy vegetables, root vegetables, grains, and tuber plants. Experimental results include the tissue free water tritium (TFWT) and the organically bound tritium (OBT) concentration of rice, soybean, cabbage, and radish exposed to HTO vapor for 1 h in the daytime at different growth stages. The model predictions showed that the model could simulate well not only the time-dependent tritium concentration of the plants but also the effect of the growth stage of the plant at the exposure time. Comparison of the model predictions with the experimental results suggested that the model could predict reasonably well the observed TFWT and OBT concentrations of the plants considered.

  17. Contamination level in vegetables grown around Peshawar using sewerage and canal water

    International Nuclear Information System (INIS)

    Mahmood, S.

    2001-01-01

    The level of contamination in vegetables grown around Peshawar using sewerage/canal water is reported. The vegetable samples were collected from three representative locations. The results indicated that vegetables grown with sewerage water contained higher levels of Cd, Cu and Pb than those with irrigation water. Maximum amount of Cd was in Qulfa (3.68 mu g/ g) followed by sponge gourd leaves (3.38 mu g/ g) the tomato leaves (93.32 mu g/ g). while Pb in tomato leaves (4.88 mu g / g), Cu content ranged between 2.08 and 7.5 mu g/g in these vegetables. In the vegetables grown with canal water the Cd ranged 0.82 - 2.88 mu g/g, Cu 2.38 mu g /g and Pb 0.84 - 1.88 mu g/ g. The concentration of Fe and P in the vegetables of sewerage water ranged 9.0-25.0 and 5.6-14.8 mg/100g respectively while those grown with canal water 9.0-11.0 mg/ 100 g and 8.4-12.8 mg/ 100 g respectively. (author)

  18. Human Factors Risk Analyses of a Doffing Protocol for Ebola-Level Personal Protective Equipment: Mapping Errors to Contamination.

    Science.gov (United States)

    Mumma, Joel M; Durso, Francis T; Ferguson, Ashley N; Gipson, Christina L; Casanova, Lisa; Erukunuakpor, Kimberly; Kraft, Colleen S; Walsh, Victoria L; Zimring, Craig; DuBose, Jennifer; Jacob, Jesse T

    2018-03-05

    Doffing protocols for personal protective equipment (PPE) are critical for keeping healthcare workers (HCWs) safe during care of patients with Ebola virus disease. We assessed the relationship between errors and self-contamination during doffing. Eleven HCWs experienced with doffing Ebola-level PPE participated in simulations in which HCWs donned PPE marked with surrogate viruses (ɸ6 and MS2), completed a clinical task, and were assessed for contamination after doffing. Simulations were video recorded, and a failure modes and effects analysis and fault tree analyses were performed to identify errors during doffing, quantify their risk (risk index), and predict contamination data. Fifty-one types of errors were identified, many having the potential to spread contamination. Hand hygiene and removing the powered air purifying respirator (PAPR) hood had the highest total risk indexes (111 and 70, respectively) and number of types of errors (9 and 13, respectively). ɸ6 was detected on 10% of scrubs and the fault tree predicted a 10.4% contamination rate, likely occurring when the PAPR hood inadvertently contacted scrubs during removal. MS2 was detected on 10% of hands, 20% of scrubs, and 70% of inner gloves and the predicted rates were 7.3%, 19.4%, 73.4%, respectively. Fault trees for MS2 and ɸ6 contamination suggested similar pathways. Ebola-level PPE can both protect and put HCWs at risk for self-contamination throughout the doffing process, even among experienced HCWs doffing with a trained observer. Human factors methodologies can identify error-prone steps, delineate the relationship between errors and self-contamination, and suggest remediation strategies.

  19. Blood Lead Levels in Children and Environmental Lead Contamination in Miami Inner City, Florida

    Directory of Open Access Journals (Sweden)

    Theophile Niyonsenga

    2006-09-01

    Full Text Available Studies have shown that the environmental conditions of the home are important predictors of health, especially in low-income communities. Understanding the relationship between the environment and health is crucial in the management of certain diseases. One health outcome related to the home environment among urban, minority, and low-income children is childhood lead poisoning. The most common sources of lead exposure for children are lead paint in older, dilapidated housing and contaminated dust and soil produced by accumulated residue of leaded gasoline. Blood lead levels (BLL as low as 10 μg/dL in children are associated with impaired cognitive function, behavior difficulties, and reduced intelligence. Recently, it is suggested that the standard for intervention be lowered to BLL of 5 μg /dl. The objectives of our report were to assess the prevalence of lead poisoning among children under six years of age and to quantify and test the correlations between BLL in children and lead exposure levels in their environment. This cross-sectional analysis was restricted to 75 children under six years of age who lived in 6 zip code areas of inner city Miami. These locations exhibited unacceptably high levels of lead dust and soil in areas where children live and play. Using the 5 μg/dL as the cutoff point, the prevalence of lead poisoning among the study sample was 13.33%. The study revealed that lead levels in floor dust and window sill samples were positively and significantly correlated with BLL among children (p < 0.05. However, the correlations between BLL and the soil, air, and water samples were not significant. Based on this pilot study, a more comprehensive environmental study in surrounding inner city areas is warranted. Parental education on proper housecleaning techniques may also benefit those living in the high lead-exposed communities of inner city Miami.

  20. Surface core-level shifts for simple metals

    DEFF Research Database (Denmark)

    Aldén, Magnus; Skriver, Hans Lomholt; Johansson, Börje

    1994-01-01

    We have performed an ab initio study of the surface core-level binding energy shift (SCLS) for 11 of the simple metals by means of a Green’s-function technique within the tight-binding linear-muffin-tin-orbitals method. Initial- and final-state effects are included within the concept of complete....... We furthermore conclude that the unexpected negative sign of the SCLS in beryllium is predominantly an initial-state effect and is caused by the high electron density in this metal....

  1. Water-related infrastructure in a region of post-earthquake Haiti: high levels of fecal contamination and need for ongoing monitoring.

    Science.gov (United States)

    Widmer, Jocelyn M; Weppelmann, Thomas A; Alam, Meer T; Morrissey, B David; Redden, Edsel; Rashid, Mohammed H; Diamond, Ulrica; Ali, Afsar; De Rochars, Madsen Beau; Blackburn, Jason K; Johnson, Judith A; Morris, J Glenn

    2014-10-01

    We inventoried non-surface water sources in the Leogane and Gressier region of Haiti (approximately 270 km(2)) in 2012 and 2013 and screened water from 345 sites for fecal coliforms and Vibrio cholerae. An international organization/non-governmental organization responsible for construction could be identified for only 56% of water points evaluated. Sixteen percent of water points were non-functional at any given time; 37% had evidence of fecal contamination, with spatial clustering of contaminated sites. Among improved water sources (76% of sites), 24.6% had fecal coliforms versus 80.9% in unimproved sources. Fecal contamination levels increased significantly from 36% to 51% immediately after the passage of Tropical Storm Sandy in October of 2012, with a return to 34% contamination in March of 2013. Long-term sustainability of potable water delivery at a regional scale requires ongoing assessment of water quality, functionality, and development of community-based management schemes supported by a national plan for the management of potable water. © The American Society of Tropical Medicine and Hygiene.

  2. Thermopiles - a new thermal desorption technology for recycling highly organic contaminated soils down to natural levels

    International Nuclear Information System (INIS)

    Haemers, J.; Cardot, J.; Falcinelli, U.; Zwaan, H.

    2005-01-01

    The Thermopile R technology, developed by Deep Green, provides an implementation system allowing to treat hydrocarbon and PAH contaminated materials down to natural levels or down to levels where they are treatable with a traditional thermal desorption unit, in a controlled batch system. The materials are indirectly heated while a substantial part of the energy is reused to heat the pile of soil. The system differs from most of the indirect thermal desorption systems by its very high energetic efficiency as well as its ability to be set -up remotely. The system does not face preferential path problems, since the heating medium is only conduction, which is very indifferent with regard to soil type (clay, sand, silt, etc.). That property is critical to an in-depth clean-up with a batch system. Other systems, based on heat, are mostly sending heat vectors (gases, hot air, steam, etc.) through the soil, which implies preferential paths, which are the main cause for not completely cleaning the soil with most batch technologies (down to natural levels). The soil to treat is placed in a pile or in a modular container in which perforated steel pipes are installed along a hexagonal pattern. During treatment those pipes are heated by hot gases (about 600 deg. C) coming from the afterburner. Consequently the soil reaches the contaminant's desorption temperature. The desorbed pollutants are then drawn by convection and diffusion into the heating pipes via the perforations. Once in the pipes the desorbed gases are mixed with the heating gases. They are sucked by the ID fan and sent to the afterburner. The hydrocarbons in gaseous phase are then oxidized in the afterburner. In this manner, they provide a part of the energy needed to heat the soil itself. The pilot unit is also equipped with a purge that allows the evacuation of a part of the gases circulating in the system; Different additional gas treatments can be applied as required by the type of contaminants and the

  3. Radiation contamination monitors

    International Nuclear Information System (INIS)

    Kato, Tsutomu; Iba, Hiroshi; Sato, Hiroshi

    1999-01-01

    To make sure of no contamination on people, used articles and working uniforms coming out of the radiation controlled area, nuclear power plants are equipped with radioactive contamination monitors. This paper outlines the basic specifications and advantages of our personnel surface contamination monitors to inspect whole-body surface contamination of people coming out, article surface contamination monitors to inspect the surface and inside contamination of used articles brought out, laundry monitors to inspect surface contamination of working uniforms used in the area before and after a wash, and whole-body counters to inspect and measure the internal contamination of a person out of the area. (author)

  4. The influence of surface contamination on the ion emission from nanosecond-pulsed laser ablation of Al and Cu

    Science.gov (United States)

    Ullah, S.; Dogar, A. H.; Qayyum, H.; Rehman, Z. U.; Qayyum, A.

    2018-04-01

    Ions emitted from planar Al and Cu targets irradiated with a 1064 nm pulsed laser were investigated with the help of a time-resolving Langmuir probe. It was found that the intensity of the ions emitted from a target area rapidly decreases with the increasing number of laser shots, and seems to reach saturation after about 10 laser shots. The saturated intensity of Al and Cu ions was approximately 0.1 and 0.3 times the intensity of the respective ions measured at the first laser shot, respectively. The higher target ion intensity for the first few shots is thought to be due to the enhanced ionization of target atoms by vacuum-ultraviolet radiations emitted from the thermally excited/ionized surface contaminants. The reduction of target ion intensity with an increasing number of laser shots thus indicates the removal of contaminants from the irradiated surface area. Laser-cleaned Al and Cu surfaces were then allowed to be recontaminated with residual vacuum gases and the ion intensity was measured at various time delays. The prolonged exposure of the cleaned target to vacuum residual gases completely restores the ion intensity. Regarding surface contaminants removal, laser shots of higher intensities were found to be more effective than a higher number of laser shots having lower intensities.

  5. Temporal dynamics of urbanization-driven environmental changes explored by metal contamination in surface sediments in a restoring urban wetland park

    International Nuclear Information System (INIS)

    Ma, Jun; Liu, Yi; Yu, Guangbin; Li, Hongbo; Yu, Shen; Jiang, Yueping; Li, Guilin; Lin, Jinchang

    2016-01-01

    Highlights: • Urban-rural distribution pattern of metals in sediment faded out with urbanization. • Urban emissions were identified as sources of metal elevation in surface sediment. • Metal level homogenization with urbanization posed a moderate risk to the public. - Abstract: Spatial patterns of metal distribution along urban-rural or multi-city gradients indicate that the urbanization process directly lead to metal enrichment and contamination in the environments. However, it has not yet looked at homogenization dynamics of an urban-rural gradient pattern over time with urbanization process in an area. This study monitored anthropogenic metals (Cr, Cu, Pb, and Zn) in surface sediments from channels of a newly-opened National Wetland Park to elucidate the urbanization-driven dissolution of urban-rural gradient pattern between 2008 and 2011. Sixty-eight surface sediment samples were taken from these channels in July of both 2008 and 2011. Results showed that a spatial distribution pattern of total metal contents along the gradient of urbanization influence, evident in 2008, was homogenized in 2011 with the area development. The lead stable isotope ratio analysis identified anthropogenic Pb origins from vehicular exhausts, cements, and coal flying ashes, which elevated metal contents in the inner channels via atmospheric deposition. Specific hazard quotients of the metal contamination in surface sediment were also assessed and enhanced over time in the study wetland park. These findings suggest that emissions from traffic, construction, and energy generation contribute metal loadings in the urbanizing environment.

  6. Temporal dynamics of urbanization-driven environmental changes explored by metal contamination in surface sediments in a restoring urban wetland park

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Jun; Liu, Yi; Yu, Guangbin; Li, Hongbo [Key Laboratory of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Yu, Shen, E-mail: syu@iue.ac.cn [Key Laboratory of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Jiang, Yueping [The Management Committee of the National Xixi Wetland Park, Hangzhou 310013 (China); Li, Guilin [Key Laboratory of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Lin, Jinchang [The Management Committee of the National Xixi Wetland Park, Hangzhou 310013 (China)

    2016-05-15

    Highlights: • Urban-rural distribution pattern of metals in sediment faded out with urbanization. • Urban emissions were identified as sources of metal elevation in surface sediment. • Metal level homogenization with urbanization posed a moderate risk to the public. - Abstract: Spatial patterns of metal distribution along urban-rural or multi-city gradients indicate that the urbanization process directly lead to metal enrichment and contamination in the environments. However, it has not yet looked at homogenization dynamics of an urban-rural gradient pattern over time with urbanization process in an area. This study monitored anthropogenic metals (Cr, Cu, Pb, and Zn) in surface sediments from channels of a newly-opened National Wetland Park to elucidate the urbanization-driven dissolution of urban-rural gradient pattern between 2008 and 2011. Sixty-eight surface sediment samples were taken from these channels in July of both 2008 and 2011. Results showed that a spatial distribution pattern of total metal contents along the gradient of urbanization influence, evident in 2008, was homogenized in 2011 with the area development. The lead stable isotope ratio analysis identified anthropogenic Pb origins from vehicular exhausts, cements, and coal flying ashes, which elevated metal contents in the inner channels via atmospheric deposition. Specific hazard quotients of the metal contamination in surface sediment were also assessed and enhanced over time in the study wetland park. These findings suggest that emissions from traffic, construction, and energy generation contribute metal loadings in the urbanizing environment.

  7. Dynamics of gas-surface interactions atomic-level understanding of scattering processes at surfaces

    CERN Document Server

    Díez Muniño, Ricardo

    2013-01-01

    This book gives a representative survey of the state of the art of research on gas-surface interactions. It provides an overview of the current understanding of gas surface dynamics and, in particular, of the reactive and non-reactive processes of atoms and small molecules at surfaces. Leading scientists in the field, both from the theoretical and the experimental sides, write in this book about their most recent advances. Surface science grew as an interdisciplinary research area over the last decades, mostly because of new experimental technologies (ultra-high vacuum, for instance), as well as because of a novel paradigm, the ‘surface science’ approach. The book describes the second transformation which is now taking place pushed by the availability of powerful quantum-mechanical theoretical methods implemented numerically. In the book, experiment and theory progress hand in hand with an unprecedented degree of accuracy and control. The book presents how modern surface science targets the atomic-level u...

  8. Potential soil contaminant levels of polychlorinated dibenzodioxins and dibenzofurans at industrial facilities employing heat transfer operations

    Energy Technology Data Exchange (ETDEWEB)

    Korte, N.E.; Muhr, C.A.; Greene, D.W.

    1992-04-01

    Certain manufacturing facilities formerly used large quantities of polychlorinated biphenyl (PCB) fluids in heat transfer operations. At many of these locations, operations have also involved PCB-containing electrical equipment. Commonly, over many years of plant operations, spills and leaks have resulted in PCB soil contamination. Dioxins and furans have been associated with PCB contamination in both the technical and popular press. Consequently, the need for analyses for dioxins and furans must be evaluated at locations where soils are contaminated with PCBs. This report presents an evaluation of potential dioxin and furan soil contamination based on heat transfer operations and spills from electrical equipment. The following five scenarios were examined for dioxin and furan contamination: (1) impurities in heat transfer fluids, (2) formation during heat transfer operations, (3) pyrolysis of heat transfer fluids, (4) impurities in dielectric fluids, and (5) pyrolysis of dielectric fluids. The potential contamination with dioxins and furans was calculated and compared with a 20 ppb guideline that has been used by the Centers for Disease Control for dioxin in subsoil. The results demonstrated that dioxins are formed only under pyrolytic conditions and only from the trichlorobenzenes present in dielectric fluids. Furans are found as impurities in PCB fluids but, as with dioxins, are not formed in significant quantities except during pyrolysis. Fortunately, pyrolytic conditions involving PCB fluids and soil contamination are unlikely; therefore, analyses for dioxin and furan contamination in soils will rarely be needed.

  9. Can volatile organic metabolites be used to simultaneously assess microbial and mite contamination level in cereal grains and coffee beans?

    Science.gov (United States)

    Salvador, Angelo C; Baptista, Inês; Barros, António S; Gomes, Newton C M; Cunha, Angela; Almeida, Adelaide; Rocha, Silvia M

    2013-01-01

    A novel approach based on headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography-time-of-flight mass spectrometry (GC×GC-ToFMS) was developed for the simultaneous screening of microbial and mite contamination level in cereals and coffee beans. The proposed approach emerges as a powerful tool for the rapid assessment of the microbial contamination level (ca. 70 min versus ca. 72 to 120 h for bacteria and fungi, respectively, using conventional plate counts), and mite contamination (ca. 70 min versus ca. 24 h). A full-factorial design was performed for optimization of the SPME experimental parameters. The methodology was applied to three types of rice (rough, brown, and white rice), oat, wheat, and green and roasted coffee beans. Simultaneously, microbiological analysis of the samples (total aerobic microorganisms, moulds, and yeasts) was performed by conventional plate counts. A set of 54 volatile markers was selected among all the compounds detected by GC×GC-ToFMS. Principal Component Analysis (PCA) was applied in order to establish a relationship between potential volatile markers and the level of microbial contamination. Methylbenzene, 3-octanone, 2-nonanone, 2-methyl-3-pentanol, 1-octen-3-ol, and 2-hexanone were associated to samples with higher microbial contamination level, especially in rough rice. Moreover, oat exhibited a high GC peak area of 2-hydroxy-6-methylbenzaldehyde, a sexual and alarm pheromone for adult mites, which in the other matrices appeared as a trace component. The number of mites detected in oat grains was correlated to the GC peak area of the pheromone. The HS-SPME/GC×GC-ToFMS methodology can be regarded as the basis for the development of a rapid and versatile method that can be applied in industry to the simultaneous assessment the level of microbiological contamination and for detection of mites in cereals grains and coffee beans.

  10. Can volatile organic metabolites be used to simultaneously assess microbial and mite contamination level in cereal grains and coffee beans?

    Directory of Open Access Journals (Sweden)

    Angelo C Salvador

    Full Text Available A novel approach based on headspace solid-phase microextraction (HS-SPME combined with comprehensive two-dimensional gas chromatography-time-of-flight mass spectrometry (GC×GC-ToFMS was developed for the simultaneous screening of microbial and mite contamination level in cereals and coffee beans. The proposed approach emerges as a powerful tool for the rapid assessment of the microbial contamination level (ca. 70 min versus ca. 72 to 120 h for bacteria and fungi, respectively, using conventional plate counts, and mite contamination (ca. 70 min versus ca. 24 h. A full-factorial design was performed for optimization of the SPME experimental parameters. The methodology was applied to three types of rice (rough, brown, and white rice, oat, wheat, and green and roasted coffee beans. Simultaneously, microbiological analysis of the samples (total aerobic microorganisms, moulds, and yeasts was performed by conventional plate counts. A set of 54 volatile markers was selected among all the compounds detected by GC×GC-ToFMS. Principal Component Analysis (PCA was applied in order to establish a relationship between potential volatile markers and the level of microbial contamination. Methylbenzene, 3-octanone, 2-nonanone, 2-methyl-3-pentanol, 1-octen-3-ol, and 2-hexanone were associated to samples with higher microbial contamination level, especially in rough rice. Moreover, oat exhibited a high GC peak area of 2-hydroxy-6-methylbenzaldehyde, a sexual and alarm pheromone for adult mites, which in the other matrices appeared as a trace component. The number of mites detected in oat grains was correlated to the GC peak area of the pheromone. The HS-SPME/GC×GC-ToFMS methodology can be regarded as the basis for the development of a rapid and versatile method that can be applied in industry to the simultaneous assessment the level of microbiological contamination and for detection of mites in cereals grains and coffee beans.

  11. Can Volatile Organic Metabolites Be Used to Simultaneously Assess Microbial and Mite Contamination Level in Cereal Grains and Coffee Beans?

    Science.gov (United States)

    Salvador, Ângelo C.; Baptista, Inês; Barros, António S.; Gomes, Newton C. M.; Cunha, Ângela; Almeida, Adelaide; Rocha, Silvia M.

    2013-01-01

    A novel approach based on headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography–time-of-flight mass spectrometry (GC×GC–ToFMS) was developed for the simultaneous screening of microbial and mite contamination level in cereals and coffee beans. The proposed approach emerges as a powerful tool for the rapid assessment of the microbial contamination level (ca. 70 min versus ca. 72 to 120 h for bacteria and fungi, respectively, using conventional plate counts), and mite contamination (ca. 70 min versus ca. 24 h). A full-factorial design was performed for optimization of the SPME experimental parameters. The methodology was applied to three types of rice (rough, brown, and white rice), oat, wheat, and green and roasted coffee beans. Simultaneously, microbiological analysis of the samples (total aerobic microorganisms, moulds, and yeasts) was performed by conventional plate counts. A set of 54 volatile markers was selected among all the compounds detected by GC×GC–ToFMS. Principal Component Analysis (PCA) was applied in order to establish a relationship between potential volatile markers and the level of microbial contamination. Methylbenzene, 3-octanone, 2-nonanone, 2-methyl-3-pentanol, 1-octen-3-ol, and 2-hexanone were associated to samples with higher microbial contamination level, especially in rough rice. Moreover, oat exhibited a high GC peak area of 2-hydroxy-6-methylbenzaldehyde, a sexual and alarm pheromone for adult mites, which in the other matrices appeared as a trace component. The number of mites detected in oat grains was correlated to the GC peak area of the pheromone. The HS-SPME/GC×GC–ToFMS methodology can be regarded as the basis for the development of a rapid and versatile method that can be applied in industry to the simultaneous assessment the level of microbiological contamination and for detection of mites in cereals grains and coffee beans. PMID:23613710

  12. Sensitive Multi-Species Emissions Monitoring: Infrared Laser-Based Detection of Trace-Level Contaminants

    Energy Technology Data Exchange (ETDEWEB)

    Steill, Jeffrey D. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Huang, Haifeng [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Hoops, Alexandra A. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Patterson, Brian D. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Birtola, Salvatore R. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Jaska, Mark [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Strecker, Kevin E. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Chandler, David W. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Bisson, Soott [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2014-09-01

    This report summarizes our development of spectroscopic chemical analysis techniques and spectral modeling for trace-gas measurements of highly-regulated low-concentration species present in flue gas emissions from utility coal boilers such as HCl under conditions of high humidity. Detailed spectral modeling of the spectroscopy of HCl and other important combustion and atmospheric species such as H 2 O, CO 2 , N 2 O, NO 2 , SO 2 , and CH 4 demonstrates that IR-laser spectroscopy is a sensitive multi-component analysis strategy. Experimental measurements from techniques based on IR laser spectroscopy are presented that demonstrate sub-ppm sensitivity levels to these species. Photoacoustic infrared spectroscopy is used to detect and quantify HCl at ppm levels with extremely high signal-to-noise even under conditions of high relative humidity. Additionally, cavity ring-down IR spectroscopy is used to achieve an extremely high sensitivity to combustion trace gases in this spectral region; ppm level CH 4 is one demonstrated example. The importance of spectral resolution in the sensitivity of a trace-gas measurement is examined by spectral modeling in the mid- and near-IR, and efforts to improve measurement resolution through novel instrument development are described. While previous project reports focused on benefits and complexities of the dual-etalon cavity ring-down infrared spectrometer, here details on steps taken to implement this unique and potentially revolutionary instrument are described. This report also illustrates and critiques the general strategy of IR- laser photodetection of trace gases leading to the conclusion that mid-IR laser spectroscopy techniques provide a promising basis for further instrument development and implementation that will enable cost-effective sensitive detection of multiple key contaminant species simultaneously.

  13. Fecal indicator bacteria contamination of fomites and household demand for surface disinfection products: a case study from Peru.

    Science.gov (United States)

    Julian, Timothy R; MacDonald, Luke H; Guo, Yayi; Marks, Sara J; Kosek, Margaret; Yori, Pablo P; Pinedo, Silvia Rengifo; Schwab, Kellogg J

    2013-11-01

    Surface-mediated disease transmission is understudied in developing countries, particularly in light of the evidence that surface concentrations of fecal bacteria typically exceed concentrations in developed countries by 10- to 100-fold. In this study, we examined fecal indicator bacterial contamination of dinner plates at 21 households in four peri-urban communities in the Peruvian Amazon. We also used surveys to estimate household use of and demand for surface disinfectants at 280 households. Despite detecting total coliform, enterococci, and Escherichia coli on 86%, 43%, and 24% of plates sampled, respectively, less than one-third of households were regularly using bleach to disinfect surfaces. Among non-users of bleach, only 3.2% of respondents reported a new demand for bleach, defined as a high likelihood of using bleach within the next year. This study highlights the potential for marketing approaches to increase use of and demand for surface disinfectants to improve domestic hygiene.

  14. Wetland Ecohydrology: stochastic description of water level fluctuations across the soil surface

    Science.gov (United States)

    Tamea, S.; Muneepeerakul, R.; Laio, F.; Ridolfi, L.; Rodriguez-Iturbe, I.

    2009-12-01

    Wetlands provide a suite of social and ecological critical functions such as being habitats of disease-carrying vectors, providing buffer zones against hurricanes, controlling sediment transport, filtering nutrients and contaminants, and a repository of great biological diversity. More recently, wetlands have also been recognized as crucial for carbon storage in the context of global climate change. Despite such importance, quantitative approaches to many aspects of wetlands are far from adequate. Therefore, improving our quantitative understanding of wetlands is necessary to our ability to maintain, manage, and restore these invaluable environments. In wetlands, hydrologic factors and ecosystem processes interplay and generate unique characteristics and a delicate balance between biotic and abiotic elements. The main hydrologic driver of wetland ecosystems is the position of the water level that, being above or below ground, determines the submergence or exposure of soil. When the water level is above the soil surface, soil saturation and lack of oxygen causes hypoxia, anaerobic functioning of microorganisms and anoxic stress in plants, that might lead to the death of non-adapted organisms. When the water level lies below the soil surface, the ecosystem becomes groundwater-dependent, and pedological and physiological aspects play their role in the soil water balance. We propose here a quantitative description of wetland ecohydrology, through a stochastic process-based water balance, driven by a marked compound Poisson noise representing rainfall events. The model includes processes such as rainfall infiltration, evapotranspiration, capillary rise, and the contribution of external water bodies, which are quantified in a simple yet realistic way. The semi-analytical steady-state probability distributions of water level spanning across the soil surface are validated with data from the Everglades (Florida, USA). The model and its results allow for a quantitative

  15. Transfer of flubendazole and tylosin from feed at cross-contamination levels to various poultry matrices.

    Science.gov (United States)

    Vandenberge, V; Delezie, E; Delahaut, P; Pierret, G; De Backer, P; Daeseleire, E; Croubels, S

    2012-09-01

    Residues of veterinary drugs and feed additives used extensively in animal husbandry are sometimes found in edible matrices. In this study, broilers received experimental feed, containing either flubendazole or tylosin, at cross-contamination levels of 2.5%, 5%, and 10% of the therapeutic dose to determine the transfer ratio of these molecules from feed to poultry matrices. Breast and thigh muscle and liver samples were collected during treatment and depletion periods and then analyzed using liquid chromatography-tandem mass spectrometry. The parent molecule flubendazole and its 2 major metabolites were quantified. After 3 to 5 d, a plateau phase was reached, and a few days after withdrawal of the experimental feed, a depletion of residues was noted. Significant difference between both muscle types was noted for flubendazole. Strong metabolization of flubendazole in the liver was seen. For tylosin, no residue concentrations above the limit of quantification could be detected in muscle. None of the residue concentrations for either molecule exceeded the corresponding maximum residue limits.

  16. Assessment of urban and industrial contamination levels in the bay of Cádiz, SW Spain.

    Science.gov (United States)

    Carrasco, M; López-Ramírez, J A; Benavente, J; López-Aguayo, F; Sales, D

    2003-03-01

    Measuring the amount of pollution is of particular importance in assessing the quality and general condition of an ecosystem. In this paper, some of the results obtained as a consequence of the specific agreement between the Environmental Agency (Consejería de Medio Ambiente, Junta de Andalucía) and the University of Cadiz to assess the environmental condition of the marine bottom and waters are showed. Physical and chemical analyses in water and sediments were undertaken at various sampling sites close to urban and industrial locations. Later on, these results were studied under statistical analysis to reveal any possible relationships between the parameters employed, and to identify any analogous behaviour between the sampling sites. Physical-chemical data revealed that sediments and waters analysed were moderately contaminated and, in addition, no great differences were found between in rising and ebbing tide conditions. Finally, considering only the pollution level, from the cluster analysis of sediments two major groups appear, one of which corresponded to those sites located in the outer bay, and the other to those situated in the inner bay. However, number 6 and 14 sampling sites cannot be associated to those groups due to be related to points with important local discharges.

  17. Occurrence of Organochlorines Contaminants in Coastal Fish from Sepetiba Bay: Levels and Human Health Repercussions

    Directory of Open Access Journals (Sweden)

    A. Pacheco Ferreira

    2013-05-01

    Full Text Available The aim of this study was to survey levels of polychlorinated biphenyls (PCBs, polychlorinated dibenzofurans (PCDFs, and polychlorinated dibenzo-p-dioxins (PCDDs in white mullet (Mugil curema, common snook (Centropomus undecimalis, and acoupa weakfish (Cynoscion acoupa, collected at Sepetiba bay, Rio de Janeiro, Brazil, March-August 2013. PCBs and PCDD/Fs were determined by High Resolution Gas Chromatography/High Resolution Mass Spectrometry (HRGC/HRMS as stated by the US EPA 1613B, 1668B, and 8290A methods. The concentration of total PCBs ranged from 0.589688 ~ 0.6981629 pg-WHO-TEQ/g ww and PCDDs/PCDFs ranged from 0.134037 ~ 0.242573 pg-WHO-TEQ/g ww. The concentrations of these contaminants on fish species currently appear to fall below critical values, and the dietary consumption of these species did not represent a risk for human health. However, seeking to avoid future problems, systematic monitoring can prevent complications to the environment, marine wildlife and public health impacts.