WorldWideScience

Sample records for surface area ranging

  1. 33 CFR 334.200 - Chesapeake Bay, Point Lookout to Cedar Point; aerial and surface firing range and target area, U...

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Chesapeake Bay, Point Lookout to... Chesapeake Bay, Point Lookout to Cedar Point; aerial and surface firing range and target area, U.S. Naval Air... of Chesapeake Bay within an area described as follows: Beginning at the easternmost extremity of...

  2. Streamlined Approach for Environmental Restoration Plan for Corrective Action Unit 484: Surface Debris, Waste Sites, and Burn Area, Tonopah Test Range, Nevada

    International Nuclear Information System (INIS)

    Bechel Nevada

    2004-01-01

    This Streamlined Approach for Environmental Restoration plan details the activities necessary to close Corrective Action Unit (CAU) 484: Surface Debris, Waste Sites, and Burn Area (Tonopah Test Range). CAU 484 consists of sites located at the Tonopah Test Range, Nevada, and is currently listed in Appendix III of the Federal Facility Agreement and Consent Order. CAU 484 consists of the following six Corrective Action Sites: (1) CAS RG-52-007-TAML, Davis Gun Penetrator Test; (2) CAS TA-52-001-TANL, NEDS Detonation Area; (3) CAS TA-52-004-TAAL, Metal Particle Dispersion Test; (4) CAS TA-52-005-TAAL, Joint Test Assembly DU Sites; (5) CAS TA-52-006-TAPL, Depleted Uranium Site; and (6) CAS TA-54-001-TANL, Containment Tank and Steel Structure

  3. High surface area calcite

    Science.gov (United States)

    Schultz, L. N.; Andersson, M. P.; Dalby, K. N.; Müter, D.; Okhrimenko, D. V.; Fordsmand, H.; Stipp, S. L. S.

    2013-05-01

    Calcite (CaCO3) is important in many fields—in nature, because it is a component of aquifers, oil reservoirs and prospective CO2 storage sites, and in industry, where it is used in products as diverse as paper, toothpaste, paint, plastic and aspirin. It is difficult to obtain high purity calcite with a high surface area but such material is necessary for industrial applications and for fundamental calcite research. Commercial powder is nearly always contaminated with growth inhibitors such as sugars, citrate or pectin and most laboratory synthesis methods deliver large precipitates, often containing vaterite or aragonite. To address this problem, we (i) adapted the method of carbonating a Ca(OH)2 slurry with CO2 gas to develop the first simple, cheap, safe and reproducible procedure using common laboratory equipment, to obtain calcite that reproducibly had a surface area of 14-17 m2/g and (ii) conducted a thorough characterization of the product. Scanning electron microscopy (SEM) revealed nanometer scale, rhombohedral crystals. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and infrared spectroscopy (IR) confirmed highly crystalline, pure calcite that more closely resembles the dimensions of the biogenic calcite produced by algae in coccoliths than other methods for synthesizing calcite. We suggest that this calcite is useful when purity and high surface area are important.

  4. Range of drainage effect of surface mines

    Energy Technology Data Exchange (ETDEWEB)

    Sozanski, J.

    1978-03-01

    This paper discusses methods of calculating the range of effects of water drainage from surface coal mines and other surface mines. It is suggested that methods based on test pumping (water drainage) are time consuming, and the results can be distorted by atmospheric factors such as rain fall or dry period. So-called empirical formulae produce results which are often incorrect. The size of a cone shaped depression calculated on the basis of empirical formulae can be ten times smaller than the size of the real depression. It is suggested that using a formula based on the Dupuit formula is superior to other methods of depression calculation. According to the derived formulae the radius of the depresion cone is a function of parameters of the water bearing horizons, size of surface mine working and of water depression. The proposed formula also takes into account the influence of atmospheric factors (water influx caused by precipitation, etc.). (1 ref.) (In Polish)

  5. Home ranges of raccoon dogs in managed and natural areas.

    Directory of Open Access Journals (Sweden)

    Karmen Süld

    Full Text Available Knowledge of space use is central to understand animals' role in ecosystems. The raccoon dog Nyctereutes procyonoides is considered as one of the most influential alien mesopredator species in Europe, having the potential to cause loss of local biodiversity and act as a vector for zoonotic diseases. We collared 12 animals to study their home range and habitat use in two areas with different management regimes in Estonia: in a protected natural area and in an intensively managed area. From May to October raccoon dogs inhabiting the natural area had considerably smaller home ranges compared to the managed area, 193.3ha±37.3SD and 391.9ha±292.9SD, respectively. This result contradicts somewhat earlier findings in other European raccoon dog populations, where the home range sizes in natural areas in summer and autumn period have usually been larger compared to managed areas. In both study areas raccoon dogs preferred watersides, where amphibians and other semi-aquatic prey are abundant, to other habitats available in their home ranges. We also studied movements of a raccoon dog pair in the managed study area in winter period. Due to mild weather conditions during the study period, raccoon dogs changed their resting sites quite often, covering a relatively large 599 ha area from November 2012 to January 2013, indicating the absence of usual winter lethargy during the mild winters.

  6. Contact area measurements on structured surfaces

    DEFF Research Database (Denmark)

    Kücükyildiz, Ömer Can; Jensen, Sebastian Hoppe Nesgaard; De Chiffre, Leonardo

    In connection with the use of brass specimens featuring structured surfaces in a tribology test, an algorithm was developed for automatic measurement of the contact area by optical means.......In connection with the use of brass specimens featuring structured surfaces in a tribology test, an algorithm was developed for automatic measurement of the contact area by optical means....

  7. Experimental characterization of micromilled surfaces by large range AFM

    DEFF Research Database (Denmark)

    Bariani, Paolo; Bissacco, Giuliano; Hansen, Hans Nørgaard

    2004-01-01

    of workpiece material, particularly when sub-micrometer chip thicknesses are considered and when machining hard materials. Quantification of surface topography is of fundamental importance for the evaluation of the generated surface; high resolution and wide measuring range being highly desirable...... for the evaluation of the distinctive behaviour of the ball end mill. The combination of the two demands is to date not matched by any measuring instrument. The paper describes an experimental investigation of surface topography of such micromachined surfaces. Accurate characterization of fine surface details...

  8. In-Situ Extended Lateral Range Surface Metrology, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop an extended lateral range capability for a dynamic optical profiling system to enable non-contact, surface roughness measurement of large and...

  9. Surface moisture estimation in urban areas

    Science.gov (United States)

    Jiang, Yitong

    Surface moisture is an important parameter because it modifies urban microclimate and surface layer meteorology. The primary objectives of this paper are: 1) to analyze the impact of surface roughness from buildings on surface moisture in urban areas; and 2) to quantify the impact of surface roughness resulting from urban trees on surface moisture. To achieve the objectives, two hypotheses were tested: 1) the distribution of surface moisture is associated with the structural complexity of buildings in urban areas; and 2) The distribution and change of surface moisture is associated with the distribution and vigor of urban trees. The study area is Indianapolis, Indiana, USA. In the part of the morphology of urban trees, Warren Township was selected due to the limitation of tree inventory data. To test the hypotheses, the research design was made to extract the aerodynamic parameters, such as frontal areas, roughness length and displacement height of buildings and trees from Terrestrial and Airborne LiDAR data, then to input the aerodynamic parameters into the urban surface energy balance model. The methodology was developed for comparing the impact of aerodynamic parameters from LiDAR data with the parameters that were derived empirically from land use and land cover data. The analytical procedures are discussed below: 1) to capture the spatial and temporal variation of surface moisture, daily and hourly Land Surface Temperature (LST) were downscaled from 4 km to 1 km, and 960 m to 30 m, respectively, by regression between LST and various components that impact LST; 2) to estimate surface moisture, namely soil moisture and evapotranspiration (ET), land surfaces were classified into soil, vegetation, and impervious surfaces, using Linear Spectral Mixture Analysis (LSMA); 3) aerodynamic parameters of buildings and trees were extracted from Airborne and Terrestrial LiDAR data; 4) the Temperature-Vegetation-Index (TVX) method, and the Two-Source-Energy-Balance (TSEB

  10. Heavy-metal contamination on training ranges at the Grafenwoehr Training Area, Germany

    Energy Technology Data Exchange (ETDEWEB)

    Zellmer, S.D.; Schneider, J.F.

    1993-05-01

    Large quantities of lead and other heavy metals are deposited in the environment of weapons ranges during training exercises. This study was conducted to determine the type, degree, and extent of heavy-metal contamination on selected handgun, rifle, and hand-grenade ranges at Grafenwoehr Training Area, Germany. Soil, vegetation, and surface-water samples were collected and analyzed using the inductively-coupled plasma atomic-emission spectroscopy (ICP-AES) method and the toxic characterization leaching procedure (TCLP). The ICP-AES results show that above-normal levels of lead and copper are in the surface soil at the handgun range, high concentrations of lead and copper are in the berm and soil surface at the rifle range, and elevated levels of cadmium and above-normal concentrations of arsenic, copper, and zinc are present in the surface soil at the hand-grenade range. The TCLP results show that surface soils can be considered hazardous waste because of lead content at the rifle range and because of cadmium concentration at the hand-grenade range. Vegetation at the handgun and rifle ranges has above-normal concentrations of lead. At the hand-grenade range, both vegetation and surface water have high levels of cadmium. A hand-held X-ray fluorescence (XRF) spectrum analyzer was used to measure lead concentrations in soils in a field test of the method. Comparison of XRF readings with ICP-AES results for lead indicate that the accuracy and precision of the hand-held XRF unit must improve before the unit can be used as more than a screening tool. Results of this study show that heavy-metal contamination at all three ranges is limited to the surface soil; heavy metals are not being leached into the soil profile or transported into adjacent areas.

  11. Photonic bandgap structures for long-range surface plasmon polaritons

    DEFF Research Database (Denmark)

    Bozhevolnyi, Sergey I.; Boltasseva, Alexandra; Søndergaard, Thomas

    2005-01-01

    Propagation of long-range surface plasmon polaritons (LR-SPPs) along periodically thickness-modulated metal stripes embedded in dielectric is studied both theoretically and experimentally for light wavelengths in the telecom range. We demonstrate that symmetric (with respect to the film surface) nm......-size thickness variations result in the pronounced band gap effect, and obtain very good agreement between measured and simulated (transmission and reflection) spectra. This effect is exploited to realize a compact wavelength add-drop filter with the bandwidth of -20 nm centered at 1550 nm. The possibilities...

  12. Monitoring System for ALICE Surface Areas

    CERN Document Server

    Demirbasci, Oguz

    2016-01-01

    I have been at CERN for 12 weeks within the scope of Summer Student Programme working on a monitoring system project for surface areas of the ALICE experiment during this period of time. The development and implementation of a monitoring system for environmental parameters in the accessible areas where a cheap hardware setup can be deployed were aim of this project. This report explains how it was developed by using Arduino, Raspberry PI, WinCC OA and DIM protocol.

  13. Water resources of the Marquette Iron Range area, Michigan

    Science.gov (United States)

    Wiitala, Sulo Werner; Newport, Thomas Gwyn; Skinner, Earl L.

    1967-01-01

    Large quantities of water are needed in the beneficiation and pelletizing processes by which the ore mined from low-grade iron-formations is upgraded into an excellent raw material for the iron and steel industry. Extensive reserves of low-grade iron-formation available for development herald an intensification of the demands upon the area's water supplies. This study was designed to provide water facts for public and private agencies in planning orderly development and in guiding the management of the water resources to meet existing and new requirements. Inland lakes and streams are the best potential sources of water for immediate development. The natural flow available for 90 percent of the time in the Middle and East Branches of the Escanaba River, the Carp River, and the Michigamme River is about 190 cubic feet per second. Potential storage sites are identified, and their complete development could increase the available supply from the above streams to about 450 cubic feet per second. Outwash deposits are the best potential sources of ground water. Large supplies could be developed from extensive outwash deposits in the eastern part of the area adjacent to Goose Lake Outlet and the East Branch Escanaba River. Other areas of outwash occur in the vicinity of Humboldt, West Branch Creek, and along the stream valleys. Streamflow data were used to make rough approximations of the ground-water potential in some areas. In general, however, the available data were not sufficient to permit quantitative evaluation of the potential ground-water supplies. Chemical quality of the surface and ground waters of the area is generally acceptable for most uses. Suspended sediment in the form of mineral tailings in effluents from ore-processing plants is a potential problem. Existing plants use settling basins to effectively remove most of the suspended material. Available records indicate that suspended-sediment concentrations and loads in the receiving waters have not been

  14. Volumes and surface areas of pendular rings

    Science.gov (United States)

    Rose, W.

    1958-01-01

    A packing of spheres is taken as a suitable model of porous media. The packing may be regular and the sphere size may be uniform, but in general, both should be random. Approximations are developed to give the volumes and surface areas of pendular rings that exist at points of sphere contact. From these, the total free volume and interfacial specific surface area are derived as expressive of the textural character of the packing. It was found that the log-log plot of volumes and surface areas of pendular rings vary linearly with the angle made by the line joining the sphere centers and the line from the center of the largest sphere to the closest edge of the pendular ring. The relationship, moreover, was found not to be very sensitive to variation in the size ratio of the spheres in contact. It also was found that the addition of pendular ring material to various sphere packings results in an unexpected decrease in the surface area of the boundaries that confine the resulting pore space. ?? 1958 The American Institute of Physics.

  15. Estimating surface area in early hominins.

    Directory of Open Access Journals (Sweden)

    Alan Cross

    Full Text Available Height and weight-based methods of estimating surface area have played an important role in the development of the current consensus regarding the role of thermoregulation in human evolution. However, such methods may not be reliable when applied to early hominins because their limb proportions differ markedly from those of humans. Here, we report a study in which this possibility was evaluated by comparing surface area estimates generated with the best-known height and weight-based method to estimates generated with a method that is sensitive to proportional differences. We found that the two methods yield indistinguishable estimates when applied to taxa whose limb proportions are similar to those of humans, but significantly different results when applied to taxa whose proportions differ from those of humans. We also found that the discrepancy between the estimates generated by the two methods is almost entirely attributable to inter-taxa differences in limb proportions. One corollary of these findings is that we need to reassess hypotheses about the role of thermoregulation in human evolution that have been developed with the aid of height and weight-based methods of estimating body surface area. Another is that we need to use other methods in future work on fossil hominin body surface areas.

  16. Osmosis and Surface Area to Volume Ratio.

    Science.gov (United States)

    Barrett, D. R. B.

    1984-01-01

    Describes an experiment designed to help students understand the concepts of osmosis and surface area to volume ratio (SA:VOL). The task for students is to compare water uptake in different sizes of potato cubes and relate differences to their SA:VOL ratios. (JN)

  17. Precision metrology of NSTX surfaces using coherent laser radar ranging

    International Nuclear Information System (INIS)

    Kugel, H.W.; Loesser, D.; Roquemore, A. L.; Menon, M. M.; Barry, R. E.

    2000-01-01

    A frequency modulated Coherent Laser Radar ranging diagnostic is being used on the National Spherical Torus Experiment (NSTX) for precision metrology. The distance (range) between the 1.5 microm laser source and the target is measured by the shift in frequency of the linearly modulated beam reflected off the target. The range can be measured to a precision of < 100microm at distances of up to 22 meters. A description is given of the geometry and procedure for measuring NSTX interior and exterior surfaces during open vessel conditions, and the results of measurements are elaborated

  18. Integrated Optical Components Utilizing Long-Range Surface Plasmon Polaritons

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra; Nikolajsen, Thomas; Leosson, Kristjan

    2005-01-01

    New optical waveguide technology for integrated optics, based on propagation of long-range surface plasmon polaritons (LR-SPPs) along metal stripes embedded in dielectric, is presented. Guiding and routing of electromagnetic radiation along nanometer-thin and micrometer-wide gold stripes embedded...

  19. On semiautomatic estimation of surface area

    DEFF Research Database (Denmark)

    Dvorak, J.; Jensen, Eva B. Vedel

    2013-01-01

    . For convex particles, the estimator is equal to four times the area of the support set (flower set) of the particle transect. We study the statistical properties of the flower estimator and compare its performance to that of two discretizations of the flower estimator, namely the pivotal estimator......In this paper, we propose a semiautomatic procedure for estimation of particle surface area. It uses automatic segmentation of the boundaries of the particle sections and applies different estimators depending on whether the segmentation was judged by a supervising expert to be satisfactory....... If the segmentation is correct the estimate is computed automatically, otherwise the expert performs the necessary measurements manually. In case of convex particles we suggest to base the semiautomatic estimation on the so-called flower estimator, a new local stereological estimator of particle surface area...

  20. Characterization of high surface area silicon oxynitrides

    International Nuclear Information System (INIS)

    Lednor, P.W.; DeRuiter, R.; Emeis, K.A.

    1992-01-01

    In heterogenous catalysis, liquid or gaseous feedstocks are converted over a solid catalyst into more desirable products. Such processes form an essential part of the oil and petrochemical industries. The solid catalyst usually consists of an inorganic phase, with or without metal particles on the surface. Examples include platinum particles on gamma alumina (a reforming catalyst used in oil processing), chromium particles on silica (an ethylene polymerization catalyst) and zeolites or amorphous silica-aluminas (used as solid acids).Oxides have been widely investigated in catalysis, and silica, alumina, and aluminosilicates find application commercially on a large scale. On the other hand, non-oxide materials such as nitrides, carbides and borides have been relatively little investigated. The main reason for this has been the lack of routes to the high surface area forms usually required in catalysis. However, this situation has changed significantly in recent years, due to the interest in high surface area non-oxides as precursors to fully dense ceramics; in this paper, the authors have reviewed synthetic routes to high surface area non-oxides

  1. High Surface Area Tunnels in Hexagonal WO₃.

    Science.gov (United States)

    Sun, Wanmei; Yeung, Michael T; Lech, Andrew T; Lin, Cheng-Wei; Lee, Chain; Li, Tianqi; Duan, Xiangfeng; Zhou, Jun; Kaner, Richard B

    2015-07-08

    High surface area in h-WO3 has been verified from the intracrystalline tunnels. This bottom-up approach differs from conventional templating-type methods. The 3.67 Å diameter tunnels are characterized by low-pressure CO2 adsorption isotherms with nonlocal density functional theory fitting, transmission electron microscopy, and thermal gravimetric analysis. These open and rigid tunnels absorb H(+) and Li(+), but not Na(+) in aqueous electrolytes without inducing a phase transformation, accessing both internal and external active sites. Moreover, these tunnel structures demonstrate high specific pseudocapacitance and good stability in an H2SO4 aqueous electrolyte. Thus, the high surface area created from 3.67 Å diameter tunnels in h-WO3 shows potential applications in electrochemical energy storage, selective ion transfer, and selective gas adsorption.

  2. Estimation of surface area and surface area measure of three-dimensional sets from digitizations

    DEFF Research Database (Denmark)

    Ziegel, Johanna; Kiderlen, Markus

    2010-01-01

    A local method for estimating surface area and surface area measure of three-dimensional objects from discrete binary images is presented. A weight is assigned to each 2 × 2 × 2 configuration of voxels and the total surface area of an object is given by summation of the local area contributions....... The method is based on an exact asymptotic result that holds for increasing resolution of the digitization. It states that the number of occurrences of a 2 ×  2 × 2 configuration is asymptotically proportional to an integral of its “h-function” with respect to the surface area measure of the object. We find...

  3. Directional couplers using long-range surface plasmon polariton waveguides

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra; Bozhevolnyi, Sergey I.

    2006-01-01

    We present an experimental study of guiding and routing of electromagnetic radiation along the nanometer-thin and micrometer-wide gold stripes embedded in a polymer via excitation of long-range surface plasmon polaritons (LR-SPPs) in a very broad wavelength range from 1000 to 1650 mn. For straight....... The transmission spectra of LR-SPP-based directional couplers are presented demonstrating an efficient (similar to 30 dB) separation of different telecom wavelength bands. Various possibilities for dynamic control of wavelength division/multiplexing with LRSPP-based directional couplers that utilize the thermo...

  4. High surface area fibrous silica nanoparticles

    KAUST Repository

    Polshettiwar, Vivek

    2014-11-11

    Disclosed are high surface area nanoparticles that have a fibrous morphology. The nanoparticles have a plurality of fibers, wherein each fiber is in contact with one other fiber and each fiber has a length of between about 1 nm and about 5000 nm. Also disclosed are applications of the nanoparticles of the present invention, and methods of fabrication of the nanoparticles of the present invention.

  5. OBSERVED ASTEROID SURFACE AREA IN THE THERMAL INFRARED

    Energy Technology Data Exchange (ETDEWEB)

    Nugent, C. R. [Infrared Processing and Analysis Center, California Institute of Technology, Pasadena, CA 91125 (United States); Mainzer, A.; Masiero, J.; Bauer, J.; Kramer, E.; Sonnett, S. [Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA 91109 (United States); Wright, E. L. [Department of Physics and Astronomy, University of California, Los Angeles, CA 90095 (United States); Grav, T. [Planetary Science Institute, Tucson, AZ (United States)

    2017-02-01

    The rapid accumulation of thermal infrared observations and shape models of asteroids has led to increased interest in thermophysical modeling. Most of these infrared observations are unresolved. We consider what fraction of an asteroid’s surface area contributes the bulk of the emitted thermal flux for two model asteroids of different shapes over a range of thermal parameters. The resulting observed surface in the infrared is generally more fragmented than the area observed in visible wavelengths, indicating high sensitivity to shape. For objects with low values of the thermal parameter, small fractions of the surface contribute the majority of thermally emitted flux. Calculating observed areas could enable the production of spatially resolved thermal inertia maps from non-resolved observations of asteroids.

  6. Long-range alpha detection applied to soil surface monitoring

    International Nuclear Information System (INIS)

    Caress, R.W.; Allander, K.S.; Bounds, J.A.; Catlett, M.M.; MacArthur, D.W.; Rutherford, D.A.

    1992-01-01

    The long-range alpha detection (LRAD) technique depends on the detection of ion pairs generated by alpha particles losing energy in air rather than on detection of the alpha particles themselves. Typical alpha particles generated by uranium will travel less than 3 cm in air. In contrast, the ions have been successfully detected many inches or feet away from the contamination. Since LRAD detection systems are sensitive to all ions simultaneously, large LRAD soil surface monitors (SSMS) can be used to collect all of the ions from a large sample. The LRAD SSMs are designed around the fan-less LRAD detector. In this case a five-sided box with an open bottom is placed on the soil surface. Ions generated by alpha decays on the soil surface are collected on a charged copper plate within the box. These ions create a small current from the plate to ground which is monitored with a sensitive electrometer. The current measured is proportional to the number of ions in the box, which is, in turn, proportional to the amount of alpha contamination on the surface of the soil. This report includes the design and construction of a 1-m by 1-m SSM as well as the results of a study at Fernald, OH, as part of the Uranium in Soils Integrated Demonstration

  7. A Simple Proof of Cauchy's Surface Area Formula

    OpenAIRE

    Tsukerman, Emmanuel; Veomett, Ellen

    2016-01-01

    We give a short and simple proof of Cauchy's surface area formula, which states that the average area of a projection of a convex body is equal to its surface area up to a multiplicative constant in the dimension.

  8. Influence of the atomic structure of crystal surfaces on the surface diffusion in medium temperature range

    International Nuclear Information System (INIS)

    Cousty, J.P.

    1981-12-01

    In this work, we have studied the influence of atomic structure of crystal surface on surface self-diffusion in the medium temperature range. Two ways are followed. First, we have measured, using a radiotracer method, the self-diffusion coefficient at 820 K (0.6 T melting) on copper surfaces both the structure and the cleanliness of which were stable during the experiment. We have shown that the interaction between mobile surface defects and steps can be studied through measurements of the anisotropy of surface self diffusion. Second, the behavior of an adatom and a surface vacancy is simulated via a molecular dynamics method, on several surfaces of a Lennard Jones crystal. An inventory of possible migration mechanisms of these surface defects has been drawn between 0.35 and 0.45 Tsub(m). The results obtained with both the methods point out the influence of the surface atomic structure in surface self-diffusion in the medium temperature range [fr

  9. Test Area C-64 Range Environmental Assessment, Revision 1

    Science.gov (United States)

    2010-10-01

    and waste processing in these areas are major contributors of water runoff and effluent components to the receiving water bodies. There is no clear...with tannins , particulates, dissolved organic matter, and iron derived from drainage through swamps and marshes. 3. Seepage stream—Seepage streams

  10. Decision 99-18: Range Petroleum Corporation application for a well licence, Sturgeon Lake Area

    International Nuclear Information System (INIS)

    1999-07-01

    Range Petroleum Corporation (Range) applied to the Alberta Energy and Utilities Board (EUB) pursuant to Section 2.020 of the Oil and Gas Conservation Regulations for a well licence to drill a sour oil well from a surface location in Legal Subdivision 4, Section 34, West of the fifth Meridian, directionally to a bottom-hole location under Sturgeon Lake. The purpose of the proposed well would be to obtain sour oil production from the Leduc Formation. The well would be a Level 1 well because it would have a potential maximum hydrogen sulphide release rate of 0.0412 cubic m/s. The EUB received objections to the application from landowners, cattle ranchers, farmers, residents, and cottage owners in the area of the proposed well. The application and intervention were considered at a public hearing on 26 January 1999 in Grande Prairie, Alberta, and the Board viewed the proposed surface location, the previous Lds 3-2 surface location, and the surrounding area prior to the hearing. Having carefully considered the evidence, the Board believed that it would be possible to drill the proposed well safely and with minimal risk, subject to attached conditions. But in light of the unique setting of the area, including the residences and the road and lake configurations, and the difficulty that would exist preparing an effective environmental review process (ERP), the Board deferred its decision on the well licence application until an approved ERP is in place

  11. Clay mineralogy in different geomorphic surfaces in sugarcane areas

    Science.gov (United States)

    Camargo, L.; Marques, J., Jr.

    2012-04-01

    The crystallization of the oxides and hydroxides of iron and aluminum and kaolinite of clay fraction is the result of pedogenetic processes controlled by the relief. These minerals have influence on the physical and chemical attributes of soil and exhibit spatial dependence. The pattern of spatial distribution is influenced by forms of relief as the geomorphic surfaces. In this sense, the studies aimed at understanding the relationship between relief and the distribution pattern of the clay fraction attributes contribute to the delineation of specific areas of management in the field. The objective of this study was to evaluate the spatial distribution of oxides and hydroxides of iron and aluminum and kaolinite of clay fraction and its relationship with the physical and chemical attributes in different geomorphic surfaces. Soil samples were collected in a transect each 25 m (100 samples) and in the sides of the same (200 samples) as well as an area of 500 ha (1 sample each six hectare). Geomorphic surfaces (GS) in the transect were mapped in detail to support mapping the entire area. The soil samples were taken to the laboratory for chemical, physical, and mineralogical analysis, and the pattern of spatial distribution of soil attributes was obtained by statistics and geostatistics. The GS I is considered the oldest surface of the study area, with depositional character, and a slope ranging from 0 to 4%. GS II and III are considered to be eroded, and the surface II plan a gentle slope that extends from the edge of the surface until the beginning of I and III. The crystallographic characteristics of the oxides and hydroxides of iron and aluminum and kaolinite showed spatial dependence and the distribution pattern corresponding to the limits present of the GS in the field. Surfaces I and II showed the best environments to the degree of crystallinity of hematite and the surface III to the greatest degree of crystallinity of goethite agreeing to the pedoenvironment

  12. Method for treatment of a surface area of steel

    NARCIS (Netherlands)

    Bhowmik, S.; Aaldert, P.J.

    2009-01-01

    The invention relates to a method for treatment of a surface area of steel by polishing said surface area and performing a plasma treatment of said surface area wherein the plasma treatment is performed at at least atmospheric conditions and wherein the plasma treatment is carried out at a power of

  13. On the diurnal ranges of Sea Surface Temperature (SST)

    Indian Academy of Sciences (India)

    This paper describes the variability in the diurnal range of SST in the north Indian Ocean using in situ measurements and tests the suitability of simple regression models in estimating the diurnal range.SST measurements obtained from 1556 drifting and 25 moored buoys were used to determine the diurnal range of SSTs.

  14. Thermal Desorption Analysis of Effective Specific Soil Surface Area

    Science.gov (United States)

    Smagin, A. V.; Bashina, A. S.; Klyueva, V. V.; Kubareva, A. V.

    2017-12-01

    A new method of assessing the effective specific surface area based on the successive thermal desorption of water vapor at different temperature stages of sample drying is analyzed in comparison with the conventional static adsorption method using a representative set of soil samples of different genesis and degree of dispersion. The theory of the method uses the fundamental relationship between the thermodynamic water potential (Ψ) and the absolute temperature of drying ( T): Ψ = Q - aT, where Q is the specific heat of vaporization, and a is the physically based parameter related to the initial temperature and relative humidity of the air in the external thermodynamic reservoir (laboratory). From gravimetric data on the mass fraction of water ( W) and the Ψ value, Polyanyi potential curves ( W(Ψ)) for the studied samples are plotted. Water sorption isotherms are then calculated, from which the capacity of monolayer and the target effective specific surface area are determined using the BET theory. Comparative analysis shows that the new method well agrees with the conventional estimation of the degree of dispersion by the BET and Kutilek methods in a wide range of specific surface area values between 10 and 250 m2/g.

  15. Surface areas of fractally rough particles studied by scattering

    International Nuclear Information System (INIS)

    Hurd, A.J.; Schaefer, D.W.; Smith, D.M.; Ross, S.B.; Le Mehaute, A.; Spooner, S.

    1989-01-01

    The small-angle scattering from fractally rough surfaces has the potential to give information on the surface area at a given resolution. By use of quantitative neutron and x-ray scattering, a direct comparison of surface areas of fractally rough powders was made between scattering and adsorption techniques. This study supports a recently proposed correction to the theory for scattering from fractal surfaces. In addition, the scattering data provide an independent calibration of molecular adsorbate areas

  16. Nondestructive, stereological estimation of canopy surface area

    DEFF Research Database (Denmark)

    Wulfsohn, Dvora-Laio; Sciortino, Marco; Aaslyng, Jesper M.

    2010-01-01

    a canopy using the smooth fractionator, (ii) sampling of leaves from the selected plants using the fractionator, and (iii) area estimation of the sampled leaves using point counting. We apply this procedure to estimate the total area of a chrysanthemum (Chrysanthemum morifolium L.) canopy and evaluate both...

  17. Surface texturing of crystalline silicon and effective area measurement

    Science.gov (United States)

    Sun, Tietun; Chen, Dong; Chui, Rongqiang

    2000-11-01

    In this paper, the surface area of solar cell is determined by the capacitance measurements of MOS structure. The texture etching technology can be controlled according to the change of silicon surface area, furthermore, the textured silicon surface and interface characteristic of solar cell can be studied by measuring the relationship of capacitance and voltage for MOS structure.

  18. Hand surface area as a percentage of body surface area in Asian children: a pilot study.

    Science.gov (United States)

    Choi, Hyuk; Park, Man Sik; Lee, Heung-Man

    2011-09-01

    The hand surface area (HSA) of one hand has been estimated as 1% of the body surface area (BSA). This does change with the patient's age, gender, and body mass index (BMI). There are many HSA studies done on adult populations, but fewer done on children. Our hypothesis in this study is that the general HSA equation for Caucasian adults cannot be applied as accurately to children and Asian people. HSA was defined as the area of the palm without fingers in this study. Children are in a stage of growth. If a child's hand growth ratio is not the same as that of an adult, the result of HSA/BSA calculation could be different. We undertook this study to determine whether or not there were any differences in HSA/BSA among Korean children (7-18 years) and adults (20-60 years), and compared our results with western data. A total of 186 boys aged between 7 and 18 years, were recruited for this study; their HSA was measured, directly. A total of 186 adults aged between 20 and 60 years were selected as well. BSA was calculated only for volunteers in subjects who HSA had been measured. From these results, HSA/BSA was calculated. HSA/BSA ratio of Korean boys was 0.69±0.05%, which was less than 1%. It is suggested that the ratio of the western data may not be applicable to Asian children, particularly, Korean children. HSA/BSA ratio can be applied in administration of drug doses and estimation of the area of burns. Copyright © 2011 Elsevier Ltd and ISBI. All rights reserved.

  19. Properties that influence the specific surface areas of carbon nanotubes and nanofibers.

    Science.gov (United States)

    Birch, M Eileen; Ruda-Eberenz, Toni A; Chai, Ming; Andrews, Ronnee; Hatfield, Randal L

    2013-11-01

    Commercially available carbon nanotubes and nanofibers were analyzed to examine possible relationships between their Brunauer-Emmett-Teller specific surface areas (SSAs) and their physical and chemical properties. Properties found to influence surface area were number of walls/diameter, impurities, and surface functionalization with hydroxyl and carboxyl groups. Characterization by electron microscopy, energy-dispersive X-ray spectrometry, thermogravimetric analysis, and elemental analysis indicates that SSA can provide insight on carbon nanomaterials properties, which can differ vastly depending on synthesis parameters and post-production treatments. In this study, how different properties may influence surface area is discussed. The materials examined have a wide range of surface areas. The measured surface areas differed from product specifications, to varying degrees, and between similar products. Findings emphasize the multiple factors that influence surface area and mark its utility in carbon nanomaterial characterization, a prerequisite to understanding their potential applications and toxicities. Implications for occupational monitoring are discussed.

  20. SurfaceWater Source Protection Areas (SPAs)

    Data.gov (United States)

    Vermont Center for Geographic Information — Source Protection Area (SPA) boundaries have been located on RF 24000 & RF 25000 scale USGS topographic maps by Water Supply Division (DEC) and VT Dept of Health...

  1. PROVE Surface albedo of Jornada Experimental Range, New Mexico, 1997

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this study was to determine the spatial variations in field measurements of broadband albedo as related to the ground cover and under a range of...

  2. The Surface Chemical Properties of Novel High Surface Area Solids ...

    African Journals Online (AJOL)

    during zeolite synthesis.22 Because raw fly ash has large quanti- ties of a host of elements, many of these will act as nucleation sites, which results in many small crystals rather than a few large ones. Acid etching removed the needle-like structures on the particle surfaces, revealing a porous underlying structure. (Fig. 1c).

  3. Comparison of diffusion charging and mobility-based methods for measurement of aerosol agglomerate surface area.

    Science.gov (United States)

    Ku, Bon Ki; Kulkarni, Pramod

    2012-05-01

    We compare different approaches to measure surface area of aerosol agglomerates. The objective was to compare field methods, such as mobility and diffusion charging based approaches, with laboratory approach, such as Brunauer, Emmett, Teller (BET) method used for bulk powder samples. To allow intercomparison of various surface area measurements, we defined 'geometric surface area' of agglomerates (assuming agglomerates are made up of ideal spheres), and compared various surface area measurements to the geometric surface area. Four different approaches for measuring surface area of agglomerate particles in the size range of 60-350 nm were compared using (i) diffusion charging-based sensors from three different manufacturers, (ii) mobility diameter of an agglomerate, (iii) mobility diameter of an agglomerate assuming a linear chain morphology with uniform primary particle size, and (iv) surface area estimation based on tandem mobility-mass measurement and microscopy. Our results indicate that the tandem mobility-mass measurement, which can be applied directly to airborne particles unlike the BET method, agrees well with the BET method. It was also shown that the three diffusion charging-based surface area measurements of silver agglomerates were similar within a factor of 2 and were lower than those obtained from the tandem mobility-mass and microscopy method by a factor of 3-10 in the size range studied. Surface area estimated using the mobility diameter depended on the structure or morphology of the agglomerate with significant underestimation at high fractal dimensions approaching 3.

  4. Surface Area Distribution Descriptor for object matching

    Directory of Open Access Journals (Sweden)

    Mohamed F. Gafar

    2010-07-01

    Full Text Available Matching 3D objects by their similarity is a fundamental problem in computer vision, computer graphics and many other fields. The main challenge in object matching is to find a suitable shape representation that can be used to accurately and quickly discriminate between similar and dissimilar shapes. In this paper we present a new volumetric descriptor to represent 3D objects. The proposed descriptor is used to match objects under rigid transformations including uniform scaling. The descriptor represents the object by dividing it into shells, acquiring the area distribution of the object through those shells. The computed areas are normalised to make the descriptor scale-invariant in addition to rotation and translation invariant. The effectiveness and stability of the proposed descriptor to noise and variant sampling density as well as the effectiveness of the similarity measures are analysed and demonstrated through experimental results.

  5. Habitat area and climate stability determine geographical variation in plant species range sizes

    DEFF Research Database (Denmark)

    Morueta-Holme, Naia; Enquist, Brian J.; McGill, Brian J.

    2013-01-01

    glaciations, are associated with broad-ranged species. In contrast, small habitat areas and a stable climate characterise areas with high concentrations of small-ranged species in the Andes, Central America and the Brazilian Atlantic Rainforest region. The joint roles of area and climate stability strengthen...

  6. Ultrahigh resolution long range surface plasmon-based sensor

    Czech Academy of Sciences Publication Activity Database

    Slavík, Radan; Homola, Jiří

    2007-01-01

    Roč. 123, č. 1 (2007), s. 10-12 ISSN 0925-4005 R&D Projects: GA ČR GP202/04/P141; GA ČR GA203/02/1326; GA ČR(CZ) GA303/03/0249 Grant - others:European Commission(XE) QLK4-CT-2002-02323; US FDA (US) FD-U-002250 Institutional research plan: CEZ:AV0Z20670512 Keywords : surface plasmon resonance * refractive index Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 2.934, year: 2007

  7. Retrieval and Mapping of Soil Texture Based on Land Surface Diurnal Temperature Range Data from MODIS.

    Science.gov (United States)

    Wang, De-Cai; Zhang, Gan-Lin; Zhao, Ming-Song; Pan, Xian-Zhang; Zhao, Yu-Guo; Li, De-Cheng; Macmillan, Bob

    2015-01-01

    Numerous studies have investigated the direct retrieval of soil properties, including soil texture, using remotely sensed images. However, few have considered how soil properties influence dynamic changes in remote images or how soil processes affect the characteristics of the spectrum. This study investigated a new method for mapping regional soil texture based on the hypothesis that the rate of change of land surface temperature is related to soil texture, given the assumption of similar starting soil moisture conditions. The study area was a typical flat area in the Yangtze-Huai River Plain, East China. We used the widely available land surface temperature product of MODIS as the main data source. We analyzed the relationships between the content of different particle soil size fractions at the soil surface and land surface day temperature, night temperature and diurnal temperature range (DTR) during three selected time periods. These periods occurred after rainfalls and between the previous harvest and the subsequent autumn sowing in 2004, 2007 and 2008. Then, linear regression models were developed between the land surface DTR and sand (> 0.05 mm), clay (soil texture. The spatial distribution of soil texture from the studied area was mapped based on the model with the minimum RMSE. A validation dataset produced error estimates for the predicted maps of sand, clay and physical clay, expressed as RMSE of 10.69%, 4.57%, and 12.99%, respectively. The absolute error of the predictions is largely influenced by variations in land cover. Additionally, the maps produced by the models illustrate the natural spatial continuity of soil texture. This study demonstrates the potential for digitally mapping regional soil texture variations in flat areas using readily available MODIS data.

  8. Retrieval and Mapping of Soil Texture Based on Land Surface Diurnal Temperature Range Data from MODIS

    Science.gov (United States)

    Wang, De-Cai; Zhang, Gan-Lin; Zhao, Ming-Song; Pan, Xian-Zhang; Zhao, Yu-Guo; Li, De-Cheng; Macmillan, Bob

    2015-01-01

    Numerous studies have investigated the direct retrieval of soil properties, including soil texture, using remotely sensed images. However, few have considered how soil properties influence dynamic changes in remote images or how soil processes affect the characteristics of the spectrum. This study investigated a new method for mapping regional soil texture based on the hypothesis that the rate of change of land surface temperature is related to soil texture, given the assumption of similar starting soil moisture conditions. The study area was a typical flat area in the Yangtze-Huai River Plain, East China. We used the widely available land surface temperature product of MODIS as the main data source. We analyzed the relationships between the content of different particle soil size fractions at the soil surface and land surface day temperature, night temperature and diurnal temperature range (DTR) during three selected time periods. These periods occurred after rainfalls and between the previous harvest and the subsequent autumn sowing in 2004, 2007 and 2008. Then, linear regression models were developed between the land surface DTR and sand (> 0.05 mm), clay (estimate soil texture. The spatial distribution of soil texture from the studied area was mapped based on the model with the minimum RMSE. A validation dataset produced error estimates for the predicted maps of sand, clay and physical clay, expressed as RMSE of 10.69%, 4.57%, and 12.99%, respectively. The absolute error of the predictions is largely influenced by variations in land cover. Additionally, the maps produced by the models illustrate the natural spatial continuity of soil texture. This study demonstrates the potential for digitally mapping regional soil texture variations in flat areas using readily available MODIS data. PMID:26090852

  9. Why Do We Need the Derivative for the Surface Area?

    Science.gov (United States)

    Hristova, Yulia; Zeytuncu, Yunus E.

    2016-01-01

    Surface area and volume computations are the most common applications of integration in calculus books. When computing the surface area of a solid of revolution, students are usually told to use the frustum method instead of the disc method; however, a rigorous explanation is rarely provided. In this note, we provide one by using geometric…

  10. Soil-geomorphic significance of land surface characteristics in an arid mountain range, Mojave Desert, USA

    Science.gov (United States)

    Hirmas, D.R.; Graham, R.C.; Kendrick, K.J.

    2011-01-01

    Mountains comprise an extensive and visually prominent portion of the landscape in the Mojave Desert, California. Landform surface properties influence the role these mountains have in geomorphic processes such as dust flux and surface hydrology across the region. The primary goal of this study was to describe and quantify land surface properties of arid-mountain landforms as a step toward unraveling the role these properties have in soil-geomorphic processes. As part of a larger soil-geomorphic study, four major landform types were identified within the southern Fry Mountains in the southwestern Mojave Desert on the basis of topography and landscape position: mountaintop, mountainflank, mountainflat (intra-range low-relief surface), and mountainbase. A suite of rock, vegetation, and morphometric land surface characteristic variables was measured at each of 65 locations across the study area, which included an associated piedmont and playa. Our findings show that despite the variation within types, landforms have distinct land surface properties that likely control soil-geomorphic processes. We hypothesize that surface expression influences a feedback process at this site where water transports sediment to low lying areas on the landscape and wind carries dust and soluble salts to the mountains where they are washed between rocks, incorporated into the soil, and retained as relatively long-term storage. Recent land-based video and satellite photographs of the dust cloud emanating from the Sierra Cucapá Mountains in response to the 7.2-magnitude earthquake near Mexicali, Mexico, support the hypothesis that these landforms are massive repositories of dust.

  11. Lage-area planar RF plasma productions by surface waves

    International Nuclear Information System (INIS)

    Nonaka, S.

    1994-01-01

    Large-area rf plasmas are confirmed to be produced by means of RF discharges inside a large-area dielectric tube. The plasma space is 73 cm x 176 cm and 2.5 cm. The plasma is thought to be produced by an odd plasma-surface wave (PSW ο ) in case of using large-area electrodes and by an even plasma-surface wave (PSW ο ) in case of without the electrodes. (author). 7 refs, 4 figs

  12. Procedure to detect impervious surfaces using satellite images and light detection and ranging (lidar) data

    Science.gov (United States)

    Rodríguez-Cuenca, B.; Alonso-Rodríguez, M. C.; Domenech-Tofiño, E.; Valcárcel Sanz, N.; Delgado-Hernández, J.; Peces-Morera, Juan José; Arozarena-Villar, Antonio

    2014-10-01

    The detection of impervious surfaces is an important issue in the study of urban and rural environments. Imperviousness refers to water's inability to pass through a surface. Although impervious surfaces represent a small percentage of the Earth's surface, knowledge of their locations is relevant to planning and managing human activities. Impervious structures are primarily manmade (e.g., roads and rooftops). Impervious surfaces are an environmental concern because many processes that modify the normal function of land, air, and water resources are initiated during their construction. This paper presents a novel method of identifying impervious surfaces using satellite images and light detection and ranging (LIDAR) data. The inputs for the procedure are SPOT images formed by four spectral bands (corresponding to red, green, near-infrared and mid-infrared wavelengths), a digital terrain model, and an .las file. The proposed method computes five decision indexes from the input data to classify the studied area into two categories: impervious (subdivided into buildings and roads) and non-impervious surfaces. The impervious class is divided into two subclasses because the elements forming this category (mainly roads and rooftops) have different spectral and height properties, and it is difficult to combine these elements into one group. The classification is conducted using a decision tree procedure. For every decision index, a threshold is set for which every surface is considered impervious or non-impervious. The proposed method has been applied to four different regions located in the north, center, and south of Spain, providing satisfactory results for every dataset.

  13. Indexing aortic valve area by body surface area increases the prevalence of severe aortic stenosis

    DEFF Research Database (Denmark)

    Jander, Nikolaus; Gohlke-Bärwolf, Christa; Bahlmann, Edda

    2014-01-01

    To account for differences in body size in patients with aortic stenosis, aortic valve area (AVA) is divided by body surface area (BSA) to calculate indexed AVA (AVAindex). Cut-off values for severe stenosis are......To account for differences in body size in patients with aortic stenosis, aortic valve area (AVA) is divided by body surface area (BSA) to calculate indexed AVA (AVAindex). Cut-off values for severe stenosis are...

  14. Corrective action investigation plan for CAU Number 453: Area 9 Landfill, Tonopah Test Range

    International Nuclear Information System (INIS)

    1997-01-01

    This Corrective Action Investigation Plan (CAIP) contains the environmental sample collection objectives and criteria for conducting site investigation activities at the Area 9 Landfill, Corrective Action Unit (CAU) 453/Corrective Action (CAS) 09-55-001-0952, which is located at the Tonopah Test Range (TTR). The TTR, included in the Nellis Air Force Range, is approximately 255 kilometers (140 miles) northwest of Las Vegas, Nevada. The Area 9 Landfill is located northwest of Area 9 on the TTR. The landfill cells associated with CAU 453 were excavated to receive waste generated from the daily operations conducted at Area 9 and from range cleanup which occurred after test activities

  15. Ranging behaviour of elephants within a small, fenced area in Addo ...

    African Journals Online (AJOL)

    The elephant population (n = 324, December 2000) in Addo Elephant National Park (AENP), South Africa, is restricted to an area (103 km2) considerably smaller than most elephant ranges. The Addo elephants' ranging behaviour was studied in order to determine whether natural patterns of male and female ranging ...

  16. Carbon balance of rewetted peatland forests in low mountain range areas, Germany

    Science.gov (United States)

    Krüger, Jan Paul; Dotterweich, Markus; Kopf, Christoph; Schüler, Gebhard; Scherzer, Jörg

    2017-04-01

    Peatland soils store a great proportion of the global soil carbon pool and are an important component of the global carbon cycle. Drainage of peatlands, for agricultural or forestry usage, leads to a loss of carbon from the soil to the atmosphere and the former carbon sink becomes a carbon source. Peatland rewetting has become a well applicable management tool to reduce the greenhouse gas emissions from peatland soils. However, the impact of rewetting on the carbon balance of drained peatland forest in low mountain range is rare. The aim of this project is to quantify the carbon balance of rewetted peatlands in the Hunsrück-Hochwald National Park. Worth protecting peatland's with forest called "Brücher" are characteristic of nature in the Hunsrück. Since the 19th century these peatlands have been drained by ditches for spruce forests. The survey of surface area of the peatlands is the first important part of the project. Furthermore, a peatland land register for the national park and adjacent areas will be developed. Based on peatland area and carbon stocks the carbon pools of different degradation stages of these peatland can be investigated. Furthermore, terrestrial laser scan data and geoelectrical measurements will be applied for estimating the carbon pool of the vegetation and the soil. This approach enables us to quantify the whole ecosystem carbon pool. A space-for-time substitution allows for a first estimation of the carbon balance of the rewetted peatlands in the Hunsrück-Hochwald National Park. The main aim of a comprehensive carbon balancing will be achieved based upon the peatland characteristics and upscaling of carbon stocks from peatlands with different restoration/degradation scenarios. Moreover, the obtained data will be used for a long-term carbon balance monitoring of the rewetted peatlands in this region.

  17. Effect of impervious surface area and vegetation changes on mean ...

    African Journals Online (AJOL)

    This land use or land cover changes are also thought to affect the climate of the Tshwane metropolis as is evidenced by heat waves in 2013 and 2014. This paper describes how vegetation and impervious surface area (ISA) or built up areas were classified from Landsat 8 LCDM, 2013, and Landsat 7 ETM+, 2003 images ...

  18. Extent of Stream Burial and Relationships to Watershed Area, Topography, and Impervious Surface Area

    Directory of Open Access Journals (Sweden)

    Roy E. Weitzell

    2016-11-01

    Full Text Available Stream burial—the routing of streams through culverts, pipes, and concrete lined channels, or simply paving them over—is common during urbanization, and disproportionately affects small, headwater streams. Burial undermines the physical and chemical processes governing life in streams, with consequences for water quality and quantity that may amplify from headwaters to downstream receiving waters. Knowledge of the extent of stream burial is critical for understanding cumulative impacts to stream networks, and for future decision-making allowing for urban development while protecting ecosystem function. We predicted stream burial across the urbanizing Potomac River Basin (USA for each 10-m stream segment in the basin from medium-resolution impervious cover data and training observations obtained from high-resolution aerial photography in a GIS. Results were analyzed across a range in spatial aggregation, including counties and independent cities, small watersheds, and regular spatial grids. Stream burial was generally correlated with total impervious surface area (ISA, with areas exhibiting ISA above 30% often subject to elevated ratios of stream burial. Recurring patterns in burial predictions related to catchment area and topographic slope were also detected. We discuss these results in the context of physiographic constraints on stream location and urban development, including implications for environmental management of aquatic resources.

  19. Pivotal role of hMT+ in long-range disambiguation of interhemispheric bistable surface motion.

    Science.gov (United States)

    Duarte, João Valente; Costa, Gabriel Nascimento; Martins, Ricardo; Castelo-Branco, Miguel

    2017-10-01

    It remains an open question whether long-range disambiguation of ambiguous surface motion can be achieved in early visual cortex or instead in higher level regions, which concerns object/surface segmentation/integration mechanisms. We used a bistable moving stimulus that can be perceived as a pattern comprehending both visual hemi-fields moving coherently downward or as two widely segregated nonoverlapping component objects (in each visual hemi-field) moving separately inward. This paradigm requires long-range integration across the vertical meridian leading to interhemispheric binding. Our fMRI study (n = 30) revealed a close relation between activity in hMT+ and perceptual switches involving interhemispheric segregation/integration of motion signals, crucially under nonlocal conditions where components do not overlap and belong to distinct hemispheres. Higher signal changes were found in hMT+ in response to spatially segregated component (incoherent) percepts than to pattern (coherent) percepts. This did not occur in early visual cortex, unlike apparent motion, which does not entail surface segmentation. We also identified a role for top-down mechanisms in state transitions. Deconvolution analysis of switch-related changes revealed prefrontal, insula, and cingulate areas, with the right superior parietal lobule (SPL) being particularly involved. We observed that directed influences could emerge either from left or right hMT+ during bistable motion integration/segregation. SPL also exhibited significant directed functional connectivity with hMT+, during perceptual state maintenance (Granger causality analysis). Our results suggest that long-range interhemispheric binding of ambiguous motion representations mainly reflect bottom-up processes from hMT+ during perceptual state maintenance. In contrast, state transitions maybe influenced by high-level regions such as the SPL. Hum Brain Mapp 38:4882-4897, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley

  20. Surface area considerations for corroding N reactor fuel

    International Nuclear Information System (INIS)

    Johnson, A.B. Jr.; Pitner, A.L.

    1996-06-01

    The N Reactor fuel is corroding at sites where the Zircaloy cladding was damaged when the fuel was discharged from the reactor. Corroding areas are clearly visible on the fuel stored in open cans in the K East Basin. There is a need to estimate the area of the corroding uranium to analyze aspects of fuel behavior as it is transitioned. from current wet storage to dry storage. In this report, the factors that contribute to open-quotes trueclose quotes surface area are analyzed in terms of what is currently known about the N Reactor fuel. Using observations from a visual examinations of the fuel in the K East wet storage facility, a value for the corroding geometric area is estimated. Based on observations of corroding uranium and surface roughness values for other metals, a surface roughness factor is also estimated and applied to the corroding K East fuel to provide an estimated open-quotes trueclose quotes surface area. While the estimated area may be modified as additional data become available from fuel characterization studies, the estimate provides a basis to assess effects of exposed uranium metal surfaces on fuel behavior in operations involved in transitioning from wet to dry storage, during shipment and staging, conditioning, and dry interim storage

  1. On the effect of topography on surface wave propagation in the ambient noise frequency range

    Science.gov (United States)

    Köhler, Andreas; Weidle, Christian; Maupin, Valérie

    2012-04-01

    Due to the increasing popularity of analyzing empirical Green's functions obtained from ambient seismic noise, more and more regional tomographical studies based on short-period surface waves are published. Results could potentially be biased in mountainous regions where topography is not small compared to the wavelength and penetration depth of the considered waves. We investigate the effect of topography on the propagation of short-period Rayleigh waves empirically by means of synthetic data using a spectral element code and a 3-D model with real topography. We show that topography along a profile through the studied area can result in an underestimation of phase velocities of up to about 0.7% at the shortest investigated period (3 s). Contrary to the expectation that this bias results from the increased surface distance along topography, we find that this error can be estimated by local topographic contrasts in the vicinity of the receiver alone. We discuss and generalize our results by considering topographic profiles through other mountain ranges and find that southern Norway is a good proxy to assess the topography effect. Nevertheless, topographic bias on phase velocity measurements is in general not large enough to significantly affect recovered velocity variations in the ambient noise frequency range.

  2. Surface Area, and Oxidation Effects on Nitridation Kinetics of Silicon Powder Compacts

    Science.gov (United States)

    Bhatt, R. T.; Palczer, A. R.

    1998-01-01

    Commercially available silicon powders were wet-attrition-milled from 2 to 48 hr to achieve surface areas (SA's) ranging from 1.3 to 70 sq m/g. The surface area effects on the nitridation kinetics of silicon powder compacts were determined at 1250 or 1350 C for 4 hr. In addition, the influence of nitridation environment, and preoxidation on nitridation kinetics of a silicon powder of high surface area (approximately equals 63 sq m/g) was investigated. As the surface area increased, so did the percentage nitridation after 4 hr in N2 at 1250 or 1350 C. Silicon powders of high surface area (greater than 40 sq m/g) can be nitrided to greater than 70% at 1250 C in 4 hr. The nitridation kinetics of the high-surface-area powder compacts were significantly delayed by preoxidation treatment. Conversely, the nitridation environment had no significant influence on the nitridation kinetics of the same powder. Impurities present in the starting powder, and those accumulated during attrition milling, appeared to react with the silica layer on the surface of silicon particles to form a molten silicate layer, which provided a path for rapid diffusion of nitrogen and enhanced the nitridation kinetics of high surface area silicon powder.

  3. Justification of Requirements to the Operating Area of the Doppler Short-Range Location System

    Directory of Open Access Journals (Sweden)

    V. A. Kovrigin

    2014-01-01

    Full Text Available The article considers some issues of matching the operating area of the Doppler shortrange location system (SRLS with the destructing area of a fragmentation warhead in a wide range of applicability with no information about the angular position of the target.When action is against the low altitude aerial targets at the sea surface background Doppler SRLS are often used to provide frequency selection of a target owing to differences in the spectral characteristics of the required signal and interferences. However, Doppler systems have an inherent disadvantage i.e. the inability to estimate the angular position of the target wit respect to the SRLS.Consequently, an arising problem to ensure the effectiveness of the combat unit, which includes the guidance system, Doppler SRLS, and fragmentation warhead is of significant practical use, when acting against the low altitude aerial targets in a wide range of encounter environment with a lack of information about the angular position of the target. The article considers a practical method for ensuring the effectiveness of the combat unit by selecting the width of the destructing elements separation angle and its orientation in space.An approximate method of geometric matching the scopes of warhead and SRLS based on computer aided numerical calculation is used. With the geometric approach to the efficiency estimation in any desired angular position of the target, Doppler SRLS should form a command to burst the warhead ensuring the straddling of the target by the field of destructing elements in an arbitrary predetermined point of conditions.Algorithms of the warhead and SRLS functioning are developed and utilized as applied programs. A Doppler SRLS model is proposed. The SRLS is integrated with semi-active Doppler homing head in case there is small-sized radar target. The article presents a mathematical description of the fragmentation warhead for relatively small misses, ignoring the air resistance

  4. Assessment of dialyzer surface in online hemodiafiltration; objective choice of dialyzer surface area

    Directory of Open Access Journals (Sweden)

    Francisco Maduell

    2015-05-01

    Conclusion: The increase in 40% and 80% of dialyzer surface area entails an increase in convective volume of 6 and 16% respectively, showing minimal differences both in convective volume and clearance capacity when UFC was greater than 45 mL/h/mmHg. It is advisable to optimise dialyser efficiency to the smallest surface area possible, adjusting treatment prescription.

  5. Surface impedance of superconductors in wide frequency ranges for wake field calculations

    International Nuclear Information System (INIS)

    Davidovskii, V.G.

    2006-01-01

    The problem of the surface impedance of superconductors in wide frequency ranges for calculations of wake fields, generated by bunches of charged particles moving axially inside a metallic vacuum chambers, is solved. The case of specular electron reflection at the superconductor surface is considered. The expression for the surface impedance of superconductors suitable for numerical computation is derived [ru

  6. Corrective Action Plan for Corrective Action Unit 424: Area 3 Landfill Complex, Tonopah Test Range, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Bechtel Nevada

    1998-08-31

    This corrective action plan provides the closure implementation methods for the Area 3 Landfill Complex, Corrective Action Unit (CAU) 424, located at the Tonopah Test Range. The Area 3 Landfill Complex consists of 8 landfill sites, each designated as a separate corrective action site.

  7. Students' and Teachers' Application of Surface Area to Volume Relationships

    Science.gov (United States)

    Taylor, Amy R.; Jones, M. Gail

    2013-02-01

    The National Science Education Standards emphasize teaching unifying concepts and processes such as basic functions of living organisms, the living environment, and scale (NRC 2011). Scale includes understanding that different characteristics, properties, or relationships within a system might change as its dimensions are increased or decreased (NRC 2011). One such relationship involves surface area to volume which is a pervasive concept that can be found throughout different sciences. This concept is important for students to not only understand the association of the two, but to also be able to apply this relationship in science contexts. The purpose of this study is to investigate the factors that influence the understanding surface area to volume relationships. This study examined middle school students', high school students', and science teachers' logical thinking skills (including proportional reasoning), visual-spatial skills, and understandings of surface area to volume relationships. Regression results indicated that participants' reasoning abilities and components of visual-spatial skills could be possible predictors for one's ability to understand surface area to volume relationships. Implications for teaching scale concepts such as surface area to volume relationships in the science classroom are discussed.

  8. Surface deformation of the secondary former mining areas

    Directory of Open Access Journals (Sweden)

    Tadeusz Głowacki

    2013-09-01

    Full Text Available The paper discuss the problem of secondary deformation observed on the surface of the land in the area of the old, non-existent copper and coal mines. The authors discuss the formation of the deformation in the final period of the mine, and after his arrest, after the close of any work of protecting the surface area of influence of mining activities. Discusses the reduction of the surface of the example of two disused mines: mining copper “Konrad” in Iwiny and “Thorez” in Walbrzych, an old coal mine. In the first part of the paper discusses a brief history of the creation of old copper basin and the Lower Silesian coal basin. It then discusses the formation of deformation processes in mining areas. Conducting continuous surveying allows you to monitor changes in the formation of land, in the paper indicate the source of the vertical displacements after ending of operation, the closure of the mine and stopped all work safety. In the area of Lower Silesia there are many remnants of disused mines, surface geodetic measurements show a constant activity in post-mining areas and the need to control the formation of the surface.

  9. Can foot anthropometric measurements predict dynamic plantar surface contact area?

    Directory of Open Access Journals (Sweden)

    Collins Natalie

    2009-10-01

    Full Text Available Abstract Background Previous studies have suggested that increased plantar surface area, associated with pes planus, is a risk factor for the development of lower extremity overuse injuries. The intent of this study was to determine if a single or combination of foot anthropometric measures could be used to predict plantar surface area. Methods Six foot measurements were collected on 155 subjects (97 females, 58 males, mean age 24.5 ± 3.5 years. The measurements as well as one ratio were entered into a stepwise regression analysis to determine the optimal set of measurements associated with total plantar contact area either including or excluding the toe region. The predicted values were used to calculate plantar surface area and were compared to the actual values obtained dynamically using a pressure sensor platform. Results A three variable model was found to describe the relationship between the foot measures/ratio and total plantar contact area (R2 = 0.77, p R2 = 0.76, p Conclusion The results of this study indicate that the clinician can use a combination of simple, reliable, and time efficient foot anthropometric measurements to explain over 75% of the plantar surface contact area, either including or excluding the toe region.

  10. Climatologies at high resolution for the earth's land surface areas

    Science.gov (United States)

    Karger, Dirk Nikolaus; Conrad, Olaf; Böhner, Jürgen; Kawohl, Tobias; Kreft, Holger; Soria-Auza, Rodrigo Wilber; Zimmermann, Niklaus E.; Linder, H. Peter; Kessler, Michael

    2017-09-01

    High-resolution information on climatic conditions is essential to many applications in environmental and ecological sciences. Here we present the CHELSA (Climatologies at high resolution for the earth's land surface areas) data of downscaled model output temperature and precipitation estimates of the ERA-Interim climatic reanalysis to a high resolution of 30 arc sec. The temperature algorithm is based on statistical downscaling of atmospheric temperatures. The precipitation algorithm incorporates orographic predictors including wind fields, valley exposition, and boundary layer height, with a subsequent bias correction. The resulting data consist of a monthly temperature and precipitation climatology for the years 1979-2013. We compare the data derived from the CHELSA algorithm with other standard gridded products and station data from the Global Historical Climate Network. We compare the performance of the new climatologies in species distribution modelling and show that we can increase the accuracy of species range predictions. We further show that CHELSA climatological data has a similar accuracy as other products for temperature, but that its predictions of precipitation patterns are better.

  11. High surface area electrode for high efficient microbial electrosynthesis

    Science.gov (United States)

    Nie, Huarong; Cui, Mengmeng; Lu, Haiyun; Zhang, Tian; Russell, Thomas; Lovley, Derek

    2012-02-01

    Microbial electrosynthesis, a process in which microorganisms directly accept electrons from an electrode to convert carbon dioxide and water into multi carbon organic compounds, affords a novel route for the generation of valuable products from electricity or even wastewater. The surface area of the electrode is critical for high production. A biocompatible, highly conductive, three-dimensional cathode was fabricated from a carbon nanotube textile composite to support the microorganism to produce acetate from carbon dioxide. The high surface area and macroscale porous structure of the intertwined CNT coated textile ?bers provides easy microbe access. The production of acetate using this cathode is 5 fold larger than that using a planar graphite electrode with the same volume. Nickel-nanowire-modified carbon electrodes, fabricated by microwave welding, increased the surface area greatly, were able to absorb more bacteria and showed a 1.5 fold increase in performance

  12. Particle surface area and bacterial activity in recirculating aquaculture systems

    DEFF Research Database (Denmark)

    Pedersen, Per Bovbjerg; von Ahnen, Mathis; Fernandes, Paulo

    2017-01-01

    Suspended particles in recirculating aquaculture systems (RAS) provide surface area that can be colonized by bacteria. More particles accumulate as the intensity of recirculation increases thus potentially increasing the bacterial carrying capacity of the systems. Applying a recent, rapid, cultur...... for determining bacterial activity might provide a means for future monitoring and assessment of microbial water quality in aquaculture farming systems......Suspended particles in recirculating aquaculture systems (RAS) provide surface area that can be colonized by bacteria. More particles accumulate as the intensity of recirculation increases thus potentially increasing the bacterial carrying capacity of the systems. Applying a recent, rapid, culture......-independent fluorometric detection method (Bactiquant®) for measuring bacterial activity, the current study explored the relationship between total particle surface area (TSA, derived from the size distribution of particles >5 μm) and bacterial activity in freshwater RAS operated at increasing intensity of recirculation...

  13. STEREOLOGICAL ESTIMATION OF SURFACE AREA FROM DIGITAL IMAGES

    Directory of Open Access Journals (Sweden)

    Johanna Ziegel

    2011-05-01

    Full Text Available A sampling design of local stereology is combined with a method from digital stereology to yield a novel estimator of surface area based on counts of configurations observed in a digitization of an isotropic 2- dimensional slice with thickness s. As a tool, a result of the second author and J. Rataj on infinitesimal increase of volumes of morphological transforms is refined and used. The proposed surface area estimator is asymptotically unbiased in the case of sets contained in the ball centred at the origin with radius s and in the case of balls centred at the origin with unknown radius. For general shapes bounds for the asymptotic expected relative worst case error are given. A simulation example is discussed for surface area estimation based on 2×2×2-configurations.

  14. Specific surface area of a crushed welded tuff before and after aqueous dissolution

    Science.gov (United States)

    Reddy, M.M.; Claassen, H.C.

    1994-01-01

    Specific surface areas were measured for several reference minerals (anorthoclase, labradorite and augite), welded tuff and stream sediments from Snowshoe Mountain, near Creede, Colorado. Crushed and sieved tuff had an unexpectedly small variation in specific surface area over a range of size fractions. Replicate surface area measurements of the largest and smallest tuff particle size fractions examined (1-0.3 mm and <0.212 mm) were 2.3 ?? 0.2 m2/g for each size fraction. Reference minerals prepared in the same way as the tuff had smaller specific surface areas than that of the tuff of the same size fraction. Higher than expected tuff specific surface areas appear to be due to porous matrix. Tuff, reacted in solutions with pH values from 2 to 6, had little change in specific surface area in comparison with unreacted tuff. Tuff, reacted with solutions having high acid concentrations (0.1 M hydrochloric acid or sulfuric-hydrofluoric acid), exhibited a marked increase in specific surface area compared to unreacted tuff. ?? 1994.

  15. An aerial radiological survey of the Tonopah Test Range including Clean Slate 1,2,3, Roller Coaster, decontamination area, Cactus Springs Ranch target areas. Central Nevada

    International Nuclear Information System (INIS)

    Proctor, A.E.; Hendricks, T.J.

    1995-08-01

    An aerial radiological survey was conducted of major sections of the Tonopah Test Range (TTR) in central Nevada from August through October 1993. The survey consisted of aerial measurements of both natural and man-made gamma radiation emanating from the terrestrial surface. The initial purpose of the survey was to locate depleted uranium (detecting 238 U) from projectiles which had impacted on the TTR. The examination of areas near Cactus Springs Ranch (located near the western boundary of the TTR) and an animal burial area near the Double Track site were secondary objectives. When more widespread than expected 241 Am contamination was found around the Clean Slates sites, the survey was expanded to cover the area surrounding the Clean Slates and also the Double Track site. Results are reported as radiation isopleths superimposed on aerial photographs of the area

  16. High surface area carbon and process for its production

    Energy Technology Data Exchange (ETDEWEB)

    Romanos, Jimmy; Burress, Jacob; Pfeifer, Peter; Rash, Tyler; Shah, Parag; Suppes, Galen

    2016-12-13

    Activated carbon materials and methods of producing and using activated carbon materials are provided. In particular, biomass-derived activated carbon materials and processes of producing the activated carbon materials with prespecified surface areas and pore size distributions are provided. Activated carbon materials with preselected high specific surface areas, porosities, sub-nm (<1 nm) pore volumes, and supra-nm (1-5 nm) pore volumes may be achieved by controlling the degree of carbon consumption and metallic potassium intercalation into the carbon lattice during the activation process.

  17. Surface barrier silicon detectors with a large active area

    International Nuclear Information System (INIS)

    Kim, Y.; Husimi, K.; Ikeda, Y.; Kim, C.; Ohkawa, S.; Sakai, T.

    1985-01-01

    Surface barrier silicon detectors with a large active area have been produced by using high resistive n-type silicon crystals, diameters of which are 3 to 5 inches. High quality detectors with a low leakage current and a low noise were achieved by developing the improved surface treatment. Characteristics of detectors obtained are good in energy resolution compared with conventional large area Si(Li) detectors. It has also been confirmed that local dead region is not found from measuring results of photo-pulse injection

  18. Stereological estimation of surface area from digital images

    DEFF Research Database (Denmark)

    Ziegel, Johanna; Kiderlen, Markus

    2010-01-01

    A sampling design of local stereology is combined with a method from digital stereology to yield a novel estimator of surface area based on counts of configurations observed in a digitization of an isotropic 2- dimensional slice with thickness s. As a tool, a result of the second author and J....... Rataj on infinitesimal increase of volumes of morphological transforms is refined and used. The proposed surface area estimator is asymptotically unbiased in the case of sets contained in the ball centred at the origin with radius s and in the case of balls centred at the origin with unknown radius...

  19. Determining Surface Roughness in Urban Areas Using Lidar Data

    Science.gov (United States)

    Holland, Donald

    2009-01-01

    An automated procedure has been developed to derive relevant factors, which can increase the ability to produce objective, repeatable methods for determining aerodynamic surface roughness. Aerodynamic surface roughness is used for many applications, like atmospheric dispersive models and wind-damage models. For this technique, existing lidar data was used that was originally collected for terrain analysis, and demonstrated that surface roughness values can be automatically derived, and then subsequently utilized in disaster-management and homeland security models. The developed lidar-processing algorithm effectively distinguishes buildings from trees and characterizes their size, density, orientation, and spacing (see figure); all of these variables are parameters that are required to calculate the estimated surface roughness for a specified area. By using this algorithm, aerodynamic surface roughness values in urban areas can then be extracted automatically. The user can also adjust the algorithm for local conditions and lidar characteristics, like summer/winter vegetation and dense/sparse lidar point spacing. Additionally, the user can also survey variations in surface roughness that occurs due to wind direction; for example, during a hurricane, when wind direction can change dramatically, this variable can be extremely significant. In its current state, the algorithm calculates an estimated surface roughness for a square kilometer area; techniques using the lidar data to calculate the surface roughness for a point, whereby only roughness elements that are upstream from the point of interest are used and the wind direction is a vital concern, are being investigated. This technological advancement will improve the reliability and accuracy of models that use and incorporate surface roughness.

  20. Classification of hydrogeologic areas and hydrogeologic flow systems in the basin and range physiographic province, southwestern United States

    Science.gov (United States)

    Anning, David W.; Konieczki, Alice D.

    2005-01-01

    The hydrogeology of the Basin and Range Physiographic Province in parts of Arizona, California, New Mexico, Utah, and most of Nevada was classified at basin and larger scales to facilitate information transfer and to provide a synthesis of results from many previous hydrologic investigations. A conceptual model for the spatial hierarchy of the hydrogeology was developed for the Basin and Range Physiographic Province and consists, in order of increasing spatial scale, of hydrogeologic components, hydrogeologic areas, hydrogeologic flow systems, and hydrogeologic regions. This hierarchy formed a framework for hydrogeologic classification. Hydrogeologic areas consist of coincident ground-water and surface-water basins and were delineated on the basis of existing sets of basin boundaries that were used in past investigations by State and Federal government agencies. Within the study area, 344 hydrogeologic areas were identified and delineated. This set of basins not only provides a framework for the classification developed in this report, but also has value for regional and subregional purposes of inventory, study, analysis, and planning throughout the Basin and Range Physiographic Province. The fact that nearly all of the province is delineated by the hydrogeologic areas makes this set well suited to support regional-scale investigations. Hydrogeologic areas are conceptualized as a control volume consisting of three hydrogeologic components: the soils and streams, basin fill, and consolidated rocks. The soils and streams hydrogeologic component consists of all surface-water bodies and soils extending to the bottom of the plant root zone. The basin-fill hydrogeologic component consists of unconsolidated and semiconsolidated sediment deposited in the structural basin. The consolidated-rocks hydrogeologic component consists of the crystalline and sedimentary rocks that form the mountain blocks and basement rock of the structural basin. Hydrogeologic areas were

  1. Incorporating climate change into conservation planning: Identifying priority areas across a species’ range

    Directory of Open Access Journals (Sweden)

    Richard G Pearson

    2012-12-01

    Full Text Available Theoretical and practical approaches associated with conservation biogeography, including ecological niche modeling, have been applied to the difficult task of determining how to incorporate climate change into conservation prioritization methodologies. Most studies have focused on identifying species that are most at risk from climate change, but here we asked, which areas within a species’ range does climate change threaten most? We explored methods for incorporating climate change within a range-wide conservation planning framework, using a case study of jaguars (Panthera onca. We used ecological niche models to estimate exposure to climate change across the range of the jaguar and incorporated these estimates into habitat quality scores for re-prioritization of high-priority areas for jaguar conservation. Methods such as these are needed to guide prioritization of geographically-specific actions for conservation across a species’ range.

  2. Indexing Glomerular Filtration Rate to Body Surface Area

    DEFF Research Database (Denmark)

    Redal-Baigorri, Belén; Rasmussen, Knud; Heaf, James Goya

    2014-01-01

    BACKGROUND: Kidney function is mostly expressed in terms of glomerular filtration rate (GFR). A common feature is the expression as ml/min per 1.73 m(2) , which represents the adjustment of the individual kidney function to a standard body surface area (BSA) to allow comparison between individuals...

  3. Plasma Creatinine, Age and Body Surface Area in Nigerian Children ...

    African Journals Online (AJOL)

    In a bid to establish reference values for plasma creatinine in children and adolescents using age, and body surface area (BSA), 462 apparently healthy Nigerian children/adolescents aged one day to 15 years were studied. They were recruited from well baby clinics, as well as primary and secondary schools. Plasma ...

  4. Evaluation of five formulae for estimating body surface area of ...

    African Journals Online (AJOL)

    Background: Physiological functions are often assessed by standardizing for body surface area (BSA) to avoid excessive variation in calculations in pediatric practice. Aim: To explore the suitability of existing formulae for estimating the BSA of Nigerian children. Subjects and Methods: This cross‑sectional study involved ...

  5. (Impervious) Surfaces on the Microclimate of Urban Area

    African Journals Online (AJOL)

    The present paper shows the considerable impacts of both vegetated and synthetic surfaces on the microclimate of urban area. Vegetation of a particular place affects the microclimate through reduced solar radiation and lower air temperature due to shading and evapotranspiration. Lower air temperatures are essential ...

  6. Installation and performance evaluation of an indigenous surface area analyser

    International Nuclear Information System (INIS)

    Pillai, S.N.; Solapurkar, M.N.; Venkatesan, V.; Prakash, A.; Khan, K.B.; Kumar, Arun; Prasad, R.S.

    2014-01-01

    An indigenously available surface area analyser was installed inside glove box and checked for its performance by analyzing uranium oxide and thorium oxide powders at RMD. The unit has been made ready for analysis of Plutonium oxide powders after incorporating several important features. (author)

  7. Influence of Ear Surface Area on Heat Tolerance of Composite ...

    African Journals Online (AJOL)

    Low correlation (r = 0.12) was observed between body weight and ear width. There were no correlations between ear width, respiratory rates and pulse rate. However, a residual correlation (r = -0.03) was obtained between ear width and body temperature. Large ear surface area in composite rabbits enhances better ...

  8. Assessment of large aperture scintillometry for large-area surface ...

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Earth System Science; Volume 126; Issue 5. Assessment of large aperture scintillometry for large-area surface energy fluxes over an irrigated cropland in north India. Abhishek Danodia V K Sehgal N R Patel R Dhakar J Mukherjee S K Saha A Senthil Kumar. Volume 126 Issue 5 July 2017 Article ...

  9. Projected distribution shifts and protected area coverage of range-restricted Andean birds under climate change

    Directory of Open Access Journals (Sweden)

    Verónica del Rosario Avalos

    2015-07-01

    Full Text Available In this study we projected the effect of anthropogenic climate change in endemic and restricted-range Andean bird species that spread out from the center of Bolivia to southeastern Peru. We also analyzed the representation of these species in protected areas. The ensemble forecasts from niche-based models indicated that 91–100% of species may reduce their range size under full and no dispersal scenarios, including five species that are currently threatened. The large range reduction (average 63% suggests these mountain species may be threatened by climate change. The strong effects due to range species losses are predicted in the humid mountain forests of Bolivia. The representation of bird species also decreased in protected areas. Partial gap species (94–86% are expected to increase over the present (62%. This suggests climate change and other non-climate stressors should be incorporated in conservations plans for the long-term persistence of these species. This study anticipates the magnitude of shifts in the distribution of endemic birds, and represents in the study area the first exploration of the representation of range-restricted Andean birds in protected areas under climate change.

  10. Comparison of two methods of surface profile extraction from multiple ultrasonic range measurements

    NARCIS (Netherlands)

    Barshan, B; Baskent, D

    Two novel methods for surface profile extraction based on multiple ultrasonic range measurements are described and compared. One of the methods employs morphological processing techniques, whereas the other employs a spatial voting scheme followed by simple thresholding. Morphological processing

  11. Surface water and groundwater interaction in Marala - Khanki area, Punjab

    International Nuclear Information System (INIS)

    Akram, W.; Ahmad, M.; Latif, Z.; Tariq, J.A.; Malik, M.R.

    2011-07-01

    Isotope hydrological investigations were carried out in two selected areas of Indus Basin viz. Haripur Area and Chashma- Taunsa Area for elucidating various aspects of surface water and groundwater interaction. Groundwater samples were collected on seasonal basis (low and high river discharge periods) while surface water samples were collected more frequently (weekly or monthly basis). Isotopic data suggested that there is no contribution of surface water to groundwater recharge in Haripur Area and rain is the prevailing source of groundwater recharge. The data further revealed that isotopic values of the Haripur pocket of Tarbela Lake are higher than those of Main Lake / Indus River meaning that there is a significant contribution of base flow in this pocket. Indus River appeared to be the dominant source of groundwater recharge at most of the locations in Chashma- Taunsa Area. Isotopic data of Indus River showed an increase at Taunsa as compared to Chashma in low flow period indicating the high contribution of base flow at this point in time. Stable isotopes were successfully used to quantify the base flow contribution. (author)

  12. Growth of contact area between rough surfaces under normal stress

    Science.gov (United States)

    Stesky, R. M.; Hannan, S. S.

    1987-05-01

    The contact area between deforming rough surfaces in marble, alabaster, and quartz was measured from thin sections of surfaces bonded under load with low viscosity resin epoxy. The marble and alabaster samples had contact areas that increased with stress at an accelerating rate. This result suggests that the strength of the asperity contacts decreased progressively during the deformation, following some form of strain weakening relationship. This conclusion is supported by petrographic observation of the thin sections that indicate that much of the deformation was cataclastic, with minor twinning of calcite and kinking of gypsum. In the case of the quartz, the observed contact area was small and increased approximately linearly with normal stress. Only the irreversible cataclastic deformation was observed; however strain-induced birefringence and cracking of the epoxy, not observed with the other rocks, suggests that significant elastic deformation occurred, but recovered during unloading.

  13. Strong asymmetry for surface modes in nonlinear lattices with long-range coupling

    International Nuclear Information System (INIS)

    Martinez, Alejandro J.; Vicencio, Rodrigo A.; Molina, Mario I.

    2010-01-01

    We analyze the formation of localized surface modes on a nonlinear cubic waveguide array in the presence of exponentially decreasing long-range interactions. We find that the long-range coupling induces a strong asymmetry between the focusing and defocusing cases for the topology of the surface modes and also for the minimum power needed to generate them. In particular, for the defocusing case, there is an upper power threshold for exciting staggered modes, which depends strongly on the long-range coupling strength. The power threshold for dynamical excitation of surface modes increases (decreases) with the strength of long-range coupling for the focusing (defocusing) cases. These effects seem to be generic for discrete lattices with long-range interactions.

  14. Areas of climate stability of species ranges in the Brazilian Cerrado

    DEFF Research Database (Denmark)

    Terribile, Levi Carina; Lima-Ribeiro, Matheus Souza; Bastos Araujo, Miguel

    2012-01-01

    Recognizing the location of climatically stable areas in the future is subjected to uncertainties from ecological niche models, climatic models, variation in species ranges responses, and from the climatic variation through time. Here, we proposed an approach based on hierarchical ANOVA to reduce...

  15. Short-range transit plan for the Phoenix urbanized area : fiscal years 1982-1986

    Science.gov (United States)

    1981-07-21

    Report presents the FY 1980-81 update of the Phoenix, Arizona, urbanized area Short Range Transit Plan. It describes a five-year plan to guide improvements of the public transportation sytem. Planning aspects of the report will be incorporated into t...

  16. Hydrogeochemical and stream sediment detailed geochemical survey for Thomas Range-Wasatch, Utah. Farmington Project area

    International Nuclear Information System (INIS)

    Butz, T.R.; Bard, C.S.; Witt, D.A.; Helgerson, R.N.; Grimes, J.G.; Pritz, P.M.

    1980-01-01

    Results of the Farmington project area of the Thomas Range-Wasatch detailed geochemical survey are reported. Field and laboratory data are presented for 71 groundwater samples, 345 stream sediment samples, and 178 radiometric readings. Statistical and areal distributions of uranium and possible uranium-related variables are given. A generalized geologic map of the project area is provided, and pertinent geologic factors which may be of significance in evaluating the potential for uranium mineralization are briefly discussed. Uranium concentrations in groundwater range from <0.20 to 21.77 ppB. The highest values are from groundwaters producing from areas in or near the Norwood Tuff and Wasatch, Evanston, and/or Echo Canyon Formations, and the Farmington Canyon Complex. The uranium:boron ratio delineates an anomalous trend associated with the Farmington Canyon Complex. Variables associated with uranium in groundwaters producing from the Norwood Tuff and Wasatch, Evanston, and/or Echo Canyon Formations include the uranium:sulfate ratio, boron, barium, potassium, lithium, silicon, chloride, selenium, and vanadium. Soluble uranium concentrations (U-FL) in stream sediments range from 0.99 to 86.41 ppM. Total uranium concentrations (U-NT) range from 1.60 to 92.40 ppM. Thorium concentrations range from <2 to 47 ppM. Anomalous concentrations of these variables are associated with the Farmington Canyon Complex. Variables which are associated with uranium include cerium, sodium, niobium, phosphorus, titanium, and yttrium

  17. Long-range surface plasmons for high-resolution surface plasmon resonance sensors

    Czech Academy of Sciences Publication Activity Database

    Nenninger, G. G.; Tobiška, Petr; Homola, Jiří; Yee, S. S.

    B74, 1/3 (2001), s. 145-151 ISSN 0925-4005. [European Conference on Optical Chemical Sensors and Biosensors EUROPT(R)ODE /5./. Lyon-Villeurbanne, 16.04.2000-19.04.2000] R&D Projects: GA ČR GA102/99/0549; GA ČR GA102/00/1536 Grant - others:Department of Defense(US) DAAD13-99-C-0032 Institutional research plan: CEZ:AV0Z2067918 Keywords : sensors * surface plasmons * biosensors Subject RIV: JB - Sensors, Measurment, Regulation Impact factor: 1.440, year: 2001

  18. Dose banding as an alternative to body surface area-based dosing of chemotherapeutic agents

    NARCIS (Netherlands)

    E. Chatelut (Etienne); M.L. White-Koning (M.); A.H.J. Mathijssen (Ron); F. Puisset (F.); S.D. Baker (Sharyn); A. Sparreboom (Alex)

    2012-01-01

    textabstractBackground: Dose banding is a recently suggested dosing method that uses predefined ranges (bands) of body surface area (BSA) to calculate each patients dose by using a single BSA-value per band. Thus, drugs with sufficient long-term stability can be prepared in advance. The main

  19. Modeling the potential area of occupancy at fine resolution may reduce uncertainty in species range estimates

    DEFF Research Database (Denmark)

    Jiménez-Alfaro, Borja; Draper, David; Nogues, David Bravo

    2012-01-01

    resolution. To illustrate the ability of fine-resolution species distribution models for obtaining new measures of species ranges and their impact in conservation planning, we estimate the potential AOO of an endangered species in alpine environments. We use field occurrences of relict Empetrum nigrum......Area of Occupancy (AOO), is a measure of species geographical ranges commonly used for species red listing. In most cases, AOO is estimated using reported localities of species distributions at coarse grain resolution, providing measures subjected to uncertainties of data quality and spatial...... Area (MPA). As defined here, the potential AOO provides spatially-explicit measures of species ranges which are permanent in the time and scarcely affected by sampling bias. The overestimation of these measures may be reduced using higher thresholds of habitat suitability, but standard rules as the MPA...

  20. Tropical cyclone rainfall area controlled by relative sea surface temperature.

    Science.gov (United States)

    Lin, Yanluan; Zhao, Ming; Zhang, Minghua

    2015-03-12

    Tropical cyclone rainfall rates have been projected to increase in a warmer climate. The area coverage of tropical cyclones influences their impact on human lives, yet little is known about how tropical cyclone rainfall area will change in the future. Here, using satellite data and global atmospheric model simulations, we show that tropical cyclone rainfall area is controlled primarily by its environmental sea surface temperature (SST) relative to the tropical mean SST (that is, the relative SST), while rainfall rate increases with increasing absolute SST. Our result is consistent with previous numerical simulations that indicated tight relationships between tropical cyclone size and mid-tropospheric relative humidity. Global statistics of tropical cyclone rainfall area are not expected to change markedly under a warmer climate provided that SST change is relatively uniform, implying that increases in total rainfall will be confined to similar size domains with higher rainfall rates.

  1. Test Area C-62 Final Range Environmental Assessment at Eglin Air Force Base, Florida

    Science.gov (United States)

    2015-06-05

    impermeable surfaces (i.e., concrete , asphalt) would result in an increase in stormwater runoff. If all past, present, and reasonably foreseeable projects...immediately to the west of the support building and has a power supply. In 2004 Eglin AFB removed the concrete block storage house (building 8757...however, concrete markers and boxes along Range Road 210 indicate that some utilities are either currently or formerly underground (U.S. Air Force

  2. The effect of impurities on the surface melt of a glacier in the Suntar Khayata Mountain Range, Russian Siberia

    Directory of Open Access Journals (Sweden)

    Nozomu eTakeuchi

    2015-12-01

    Full Text Available We investigated characteristics of impurities and their impact on the ablation of Glacier No.31 in the Suntar-Khayata Mountain Range in Russian Siberia during summer 2014. Positive degree-day factors (PDDFs obtained from 20 stake measurements distributed across the glacier’s ablation area varied from 3.00 to 8.55 mm w.e. K-1 day-1. The surface reflectivity measured with a spectrometer as a proxy for albedo, ranged from 0.09 to 0.62, and was negatively correlated with the PDDF, suggesting that glacier ablation is controlled by surface albedo on the studied glacier. Mass of total insoluble impurities on the ice surface varied from 0.1 to 45.2 g m-2 and was not correlated with surface reflectivity, suggesting that albedo is not directly conditioned by the mass of the impurities. Microscopy of impurities revealed that they comprised mineral particles, cryoconite granules, and ice algal cells filled with dark-reddish pigments (Ancylonema nordenskioldii. There was a significant negative correlation between surface reflectivity and algal biomass or organic matter, suggesting that the ice algae and their products are the most effective constituents in defining glacier surface albedo. Our results suggest that the melting of ice surface was enhanced by the growth of ice algae, which increased the melting rate 1.6 - 2.6 times greater than that of the impurity free bare-ice.

  3. Spectral theory of infinite-area hyperbolic surfaces

    CERN Document Server

    Borthwick, David

    2016-01-01

    This text introduces geometric spectral theory in the context of infinite-area Riemann surfaces, providing a comprehensive account of the most recent developments in the field. For the second edition the context has been extended to general surfaces with hyperbolic ends, which provides a natural setting for development of the spectral theory while still keeping technical difficulties to a minimum. All of the material from the first edition is included and updated, and new sections have been added. Topics covered include an introduction to the geometry of hyperbolic surfaces, analysis of the resolvent of the Laplacian, scattering theory, resonances and scattering poles, the Selberg zeta function, the Poisson formula, distribution of resonances, the inverse scattering problem, Patterson-Sullivan theory, and the dynamical approach to the zeta function. The new sections cover the latest developments in the field, including the spectral gap, resonance asymptotics near the critical line, and sharp geometric constan...

  4. Measurements of long-range interactions between protein-functionalized surfaces by total internal reflection microscopy.

    Science.gov (United States)

    Wang, Zhaohui; Gong, Xiangjun; Ngai, To

    2015-03-17

    Understanding the interaction between protein-functionalized surfaces is an important subject in a variety of protein-related processes, ranging from coatings for biomedical implants to targeted drug carriers and biosensors. In this work, utilizing a total internal reflection microscope (TIRM), we have directly measured the interactions between micron-sized particles decorated with three types of common proteins concanavalin A (ConA), bovine serum albumin (BSA), lysozyme (LYZ), and glass surface coated with soy proteins (SP). Our results show that the protein adsorption greatly affects the charge property of the surfaces, and the interactions between those protein-functionalized surfaces depend on solution pH values. At pH 7.5-10.0, all these three protein-functionalized particles are highly negatively charged, and they move freely above the negatively charged SP-functionalized surface. The net interaction between protein-functionalized surfaces captured by TIRM was found as a long-range, nonspecific double-layer repulsion. When pH was decreased to 5.0, both protein-functionalized surfaces became neutral and double-layer repulsion was greatly reduced, resulting in adhesion of all three protein-functionalized particles to the SP-functionalized surface due to the hydrophobic attraction. The situation is very different at pH = 4.0: BSA-decorated particles, which are highly charged, can move freely above the SP-functionalized surfaces, while ConA- and LYZ-decorated particles can only move restrictively in a limited range. Our results quantify these nonspecific kT-scale interactions between protein-functionalized surfaces, which will enable the design of surfaces for use in biomedical applications and study of biomolecular interactions.

  5. DMSA scan nomograms for renal length and area: Related to patient age and to body weight, height or surface area

    International Nuclear Information System (INIS)

    Hassan, I.M.; Que, L.; Rutland, M.D.

    2002-01-01

    Aim: To create nomograms for renal size as measured from DMSA renal studies, and to test the nomograms for their ability to separate normal from abnormal kidneys. Method: Renal length was measured from posterior oblique views and renal area from posterior views. Results from 253 patients with bilateral normal kidneys were used to create nomograms for renal size relative to patient age, body height, weight or body surface area (BSA). The nomograms enclosed 95% of the normal kidneys, thus indicating the range for 95% confidence limits, and hence the specificity. Each nomogram was then tested against 46 hypertrophied kidneys and 46 damaged kidneys. Results: The results from nomograms of renal length and renal area, compared to age, body height, body weight and BSA are presented. For each nomogram, the range is presented as a fraction of the mean value, and the number of abnormal kidneys (hypertrophied or damaged) outside the normal range is presented as a percentage (indicating the sensitivity). Conclusion: Renal Area was no better than renal length for detecting abnormal kidneys. Patient age was the least useful method of normalisation. BSA normalisation produced the best results most frequently (narrower ranges and highest detection of abnormal kidneys)

  6. Closure Report for Corrective Action Unit 425: Area 9 Main Lake Construction Debris Disposal Area, Tonopah Test Range, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    K. B. Campbell

    2003-03-01

    Corrective Action Unit (CAU) 425 is located on the Tonopah Test Range, approximately 386 kilometers (240 miles) northwest of Las Vegas, Nevada. CAU 425 is listed in the Federal Facility Agreement and Consent Order (FFACO, 1996) and is comprised of one Corrective Action Site (CAS). CAS 09-08-001-TA09 consisted of a large pile of concrete rubble from the original Hard Target and construction debris associated with the Tornado Rocket Sled Tests. CAU 425 was closed in accordance with the FFACO and the Nevada Division of Environmental Protection-approved Streamlined Approach for Environmental Restoration Plan for CAU 425: Area 9 Main Lake Construction Debris Disposal Area, Tonopah Test Range, Nevada (U.S. Department of Energy, Nevada Operations Office, 2002). CAU 425 was closed by implementing the following corrective actions: The approved corrective action for this unit was clean closure. Closure activities included: (1) Removal of all the debris from the site. (2) Weighing each load of debris leaving the job site. (3) Transporting the debris to the U.S. Air Force Construction Landfill for disposal. (4) Placing the radioactive material in a U.S. Department of Transportation approved container for proper transport and disposal. (5) Transporting the radioactive material to the Nevada Test Site for disposal. (6) Regrading the job site to its approximate original contours/elevation.

  7. Dye-Sensitized Solar Cells Based on High Surface Area Nanocrystalline Zinc Oxide Spheres

    Directory of Open Access Journals (Sweden)

    Pavuluri Srinivasu

    2011-01-01

    Full Text Available High surface area nanocrystalline zinc oxide material is fabricated using mesoporous nanostructured carbon as a sacrificial template through combustion process. The resulting material is characterized by XRD, N2 adsorption, HR-SEM, and HR-TEM. The nitrogen adsorption measurement indicates that the materials possess BET specific surface area ca. 30 m2/g. Electron microscopy images prove that the zinc oxide spheres possess particle size in the range of 0.12 μm–0.17 μm. The nanocrystalline zinc oxide spheres show 1.0% of energy conversion efficiency for dye-sensitized solar cells.

  8. Solvent accessible surface area (ASA) of simulated phospholipid membranes

    DEFF Research Database (Denmark)

    Tuchsen, E.; Jensen, Morten Østergaard; Westh, P.

    2003-01-01

    The membrane-solvent interface has been investigated through calculations of the solvent accessible surface area (ASA) for simulated membranes of DPPC and POPE. For DPPC at 52 degreesC we found an ASA of 126 +/- 8 Angstrom(2) per lipid molecule, equivalent to twice the projected lateral area......, even the most exposed parts of the PC head-group show average ASAs of less than half of its maximal or 'fully hydrated' value. The average ASA of a simulated POPE membrane was 96 +/- 7 Angstrom(2) per lipid. The smaller value than for DPPC reflects much lower ASA of the ammonium ion, which is partially...... compensated by increased exposure of the ethylene and phosphate moieties. The ASA of the polar moieties Of (PO4, NH3 and COO) constitutes 65% of the total accessible area for POPE, making this interface more polar than that of DPPC. It is suggested that ASA information can be valuable in attempts...

  9. Corrective action investigation plan for CAU No. 424: Area 3 Landfill Complex, Tonopah Test Range, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-04-01

    This Correction Action Investigation Plan contains the environmental sample collection objectives and the criteria for conducting site investigation activities at the Area 3 Landfill Complex, CAU No. 424, which is located at the Tonopah Test Range (TTR). The TTR, included in the Nellis Air Force Range, is approximately 255 kilometers (140 miles) northwest of Las Vegas, nevada. The CAU 424 is comprised of eight individual landfill sites that are located around and within the perimeter of the Area 3 Compound. Due to the unregulated disposal activities commonly associated with early landfill operations, an investigation will be conducted at each CAS to complete the following tasks: identify the presence and nature of possible contaminant migration from the landfills; determine the vertical and lateral extent of possible contaminant migration; ascertain the potential impact to human health and the environment; and provide sufficient information and data to develop and evaluate appropriate corrective action strategies for each CAS.

  10. Corrective action investigation plan for CAU No. 424: Area 3 Landfill Complex, Tonopah Test Range, Nevada

    International Nuclear Information System (INIS)

    1997-04-01

    This Correction Action Investigation Plan contains the environmental sample collection objectives and the criteria for conducting site investigation activities at the Area 3 Landfill Complex, CAU No. 424, which is located at the Tonopah Test Range (TTR). The TTR, included in the Nellis Air Force Range, is approximately 255 kilometers (140 miles) northwest of Las Vegas, nevada. The CAU 424 is comprised of eight individual landfill sites that are located around and within the perimeter of the Area 3 Compound. Due to the unregulated disposal activities commonly associated with early landfill operations, an investigation will be conducted at each CAS to complete the following tasks: identify the presence and nature of possible contaminant migration from the landfills; determine the vertical and lateral extent of possible contaminant migration; ascertain the potential impact to human health and the environment; and provide sufficient information and data to develop and evaluate appropriate corrective action strategies for each CAS

  11. Can We Trust Real Time Measurements of Lung Deposited Surface Area Concentrations in Dust from Powder Nanomaterials?

    DEFF Research Database (Denmark)

    Levin, Marcus; Witschger, Olivier; Bau, Sebastien

    2016-01-01

    A comparison between various methods for real-time measurements of lung deposited surface area (LDSA) using spherical particles and powder dust with specific surface area ranging from 0.03 to 112 m2 g-1 was conducted. LDSA concentrations measured directly using Nanoparticle Surface Area Monitor...... (NSAM) and Aerotrak and were compared to LDSA concentrations recalculated from size distribution measurements using Electrical Low Pressure Impactor (ELPI) and Fast Mobility Particle Sizer (FMPS). FMPS and ELPI measurements were also compared to dust surface area concentrations estimated from...... gravimetrical filter measurements and specific surface areas. Measurement of LDSA showed very good correlation in measurements of spherical particles (R2 > 0.97, Ratio 1.0 to 1.04). High surface area nanomaterial powders showed a fairly reliable correlation between NSAM and Aerotrak (R2 0...

  12. Former Spencer Artillery Range, Tennessee Classification Demonstration Open Field and Dynamic Areas

    Science.gov (United States)

    2016-01-01

    capabilities of the production community by enhancing and streamlining UX -Analyze’s workflow and functionality; by offering training documents...Inc. UXA UX -Analyze List of Figures Figure 3-1: Spencer Range Open Area Metal Mapper ROC Curve ............................................... 5...easting and horizontal is less than 0.1 meter. Statistics calculations are part of the Geosoft UX -Analyze (UXA) process module for IVS and include, in

  13. Hydrogeochemical and stream sediment detailed geochemical survey for Thomas Range-Wasatch, Utah. Cottonwood project area

    International Nuclear Information System (INIS)

    Butz, T.R.; Bard, C.S.; Witt, D.A.; Helgerson, R.N.; Grimes, J.G.; Pritz, P.M.

    1980-01-01

    Results of Cottonwood project area of the Thomas Range-Wasatch detailed geochemical survey are reported. Field and laboratory data are presented for 15 groundwater samples, 79 stream sediment samples, and 85 radiometric readings. Statistical and areal distributions of uranium and possible uranium-related variables are given. A generalized geologic map of the project area is provided, and pertinent geologic factors which may be of significance in evaluating the potential for uranium mineralization are briefly discussed. Uranium concentrations in groundwater range from 0.25 to 3.89 ppB. The highest concentrations are from groundwaters from the Little Cottonwood and Ferguson Stocks. Variables that appear to be associated with uranium in groundwater include cobalt, iron, potassium, manganese, nickel, sulfate, and to a lesser extent, molybdenum and strontium. This association is attributed to the Monzonitic Little Cottonwood Stock, granodioritic to granitic and lamprophyric dikes, and known sulfide deposits. Soluble uranium concentrations (U-FL) in stream sediments range from 0.31 to 72.64 ppM. Total uranium concentrations (U-NT) range from 1.80 to 75.20 ppM. Thorium concentrations range from <2 to 48 ppM. Anomalous values for uranium and thorium are concentrated within the area of outcrop of the Little Cottonwood and Ferguson Stocks. Variables which are areally associated with high values of uranium, thorium, and the U-FL:U-NT ratio within the Little Cottonwood Stock are barium, copper, molybdenum, and zinc. High concentrations of these variables are located near sulfide deposits within the Little Cottonwood Stock

  14. Short range laser obstacle detector. [for surface vehicles using laser diode array

    Science.gov (United States)

    Kuriger, W. L. (Inventor)

    1973-01-01

    A short range obstacle detector for surface vehicles is described which utilizes an array of laser diodes. The diodes operate one at a time, with one diode for each adjacent azimuth sector. A vibrating mirror a short distance above the surface provides continuous scanning in elevation for all azimuth sectors. A diode laser is synchronized with the vibrating mirror to enable one diode laser to be fired, by pulses from a clock pulse source, a number of times during each elevation scan cycle. The time for a given pulse of light to be reflected from an obstacle and received is detected as a measure of range to the obstacle.

  15. 78 FR 51176 - Record of Decision for the Modernization and Enhancement of Ranges, Airspace, and Training Areas...

    Science.gov (United States)

    2013-08-20

    ... Enhancement of Ranges, Airspace, and Training Areas in the Joint Pacific Alaska Range Complex in Alaska ACTION... Enhancement of Ranges, Airspace, and Training Areas in the Joint Pacific Alaska Range Complex (JPARC) in... the EIS, including technical considerations, public review and Tribal and agency input. The Final EIS...

  16. Molecularly-Limited Fractal Surface Area of Mineral Powders

    Directory of Open Access Journals (Sweden)

    Petr Jandacka

    2016-05-01

    Full Text Available The topic of the specific surface area (SSA of powders is not sufficiently described in the literature in spite of its nontrivial contribution to adsorption and dissolution processes. Fractal geometry provides a way to determine this parameter via relation SSA ~ x(D − 3s(2 − D, where x (m is the particle size and s (m is a scale. Such a relation respects nano-, micro-, or macro-topography on the surface. Within this theory, the fractal dimension 2 ≤ D < 3 and scale parameter s plays a significant role. The parameter D may be determined from BET or dissolution measurements on several samples, changing the powder particle sizes or sizes of adsorbate molecules. If the fractality of the surface is high, the SSA does not depend on the particle size distribution and vice versa. In this paper, the SSA parameter is analyzed from the point of view of adsorption and dissolution processes. In the case of adsorption, a new equation for the SSA, depending on the term (2 − D∙(s2 − sBET/sBET, is derived, where sBET and s2 are effective cross-sectional diameters for BET and new adsorbates. Determination of the SSA for the dissolution process appears to be very complicated, since the fractality of the surface may change in the process. Nevertheless, the presented equations have good application potential.

  17. Study of measurement methods of ultrafine aerosols surface-area for characterizing occupational exposure

    International Nuclear Information System (INIS)

    Bau, S.

    2008-12-01

    This work aims at improving knowledge on ultrafine aerosols surface-area measurement. Indeed, the development of nano-technologies may lead to occupational exposure to airborne nano-structured particles, which involves a new prevention issue. There is currently no consensus concerning what parameter (mass, surface-area, number) should be measured. However, surface-area could be a relevant metric, since it leads to a satisfying correlation with biological effects when nano-structured particles are inhaled. Hence, an original theoretical work was performed to position the parameter of surface-area in relation to other aerosol characteristics. To investigate measurement techniques of nano-structured aerosols surface-area, the experimental facility CAIMAN (Characterization of Instruments for the Measurement of Aerosols of Nano-particles) was designed and built. Within CAIMAN, it is possible to produce nano-structured aerosols with varying and controlled properties (size, concentration, chemical nature, morphology, state-of-charge), stable and reproducible in time. The generated aerosols were used to experimentally characterize the response of the instruments in study (NSAM and AeroTrak 9000 TSI, LQ1-DC Matter Engineering). The response functions measured with monodisperse aerosols show a good agreement with the corresponding theoretical curves in a large size range, from 15 to 520 nm. Furthermore, hypotheses have been formulated to explain the reasonable biases observed when measuring poly-disperse aerosols. (author)

  18. Air defense planning for an area with the use of very short range air defense sets

    Directory of Open Access Journals (Sweden)

    Tadeusz Pietkiewicz

    2017-12-01

    Full Text Available This paper presents a heuristic method of planning the deployment of very short-range anti-air missile and artillery sets (VSHORAD around an area (‘protected area’ in order to protect it. A function dependent on the distance between the earliest feasible points of destroying targets and the centre of the protected area was taken as an objective function. This is a different indicator from those commonly used in the literature, and based on the likelihood of a defense zone penetration by means of an air attack (MAA: the kill probability of the MAA and the probability of area losses. The model constraints resulted directly from the restrictions imposed by real air defense systems and the nature of the area being defended. This paper assumes that the VSHORAD system operates as a part of a general, superordinate air defense command and control system based on the idea of network-centric warfare, which provides the VSHORAD system with a recognized air picture, air defense plans, and combat mission specifications. The presented method has been implemented. The final part of the paper presents the computational results. Keywords: optimal planning, air defense system, area installation protection, deployment of very short range anti-air missile and artillery sets (VSHORAD

  19. Perfluorinated compounds in soil, surface water, and groundwater from rural areas in eastern China.

    Science.gov (United States)

    Chen, Shu; Jiao, Xing-Chun; Gai, Nan; Li, Xiao-Jie; Wang, Xiao-Chun; Lu, Guo-Hui; Piao, Hai-Tao; Rao, Zhu; Yang, Yong-Liang

    2016-04-01

    Little research on perfluorinated compounds (PFCs) has been conducted in rural areas, although rural PFC sources are less complicated than in urban and industrial areas. To determine the levels and geographical distribution of 17 PFC compounds, samples of soil, surface water, and groundwater were collected from eight rural areas in eastern China. The total PFC concentrations (∑PFCs) in soils ranged from 0.34 to 65.8 ng/g ∑PFCs in surface waters ranged from 7.0 to 489 ng/L and ∑PFCs in groundwater ranged from 5.3 to 615 ng/L. Ratios of perfluorononanoic acid/perfluorooctanoic acid (PFNA/PFOA), perfluoro-n-butyric acid/perfluorooctanoic acid (PFBA/PFOA), and perfluoroheptanoic acid/perfluorooctanoic acid (PFHpA/PFOA) in rainwater increased due to the fluorine chemical plants in the surrounding rural and urban areas, suggesting that atmospheric precipitation may carry PFCs and their precursors from the fluorochemical industrial area to the adjacent rural areas. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Metal-organic framework materials with ultrahigh surface areas

    Science.gov (United States)

    Farha, Omar K.; Hupp, Joseph T.; Wilmer, Christopher E.; Eryazici, Ibrahim; Snurr, Randall Q.; Gomez-Gualdron, Diego A.; Borah, Bhaskarjyoti

    2015-12-22

    A metal organic framework (MOF) material including a Brunauer-Emmett-Teller (BET) surface area greater than 7,010 m.sup.2/g. Also a metal organic framework (MOF) material including hexa-carboxylated linkers including alkyne bond. Also a metal organic framework (MOF) material including three types of cuboctahedron cages fused to provide continuous channels. Also a method of making a metal organic framework (MOF) material including saponifying hexaester precursors having alkyne bonds to form a plurality of hexa-carboxylated linkers including alkyne bonds and performing a solvothermal reaction with the plurality of hexa-carboxylated linkers and one or more metal containing compounds to form the MOF material.

  1. Asymptotic variance of grey-scale surface area estimators

    DEFF Research Database (Denmark)

    Svane, Anne Marie

    Grey-scale local algorithms have been suggested as a fast way of estimating surface area from grey-scale digital images. Their asymptotic mean has already been described. In this paper, the asymptotic behaviour of the variance is studied in isotropic and sufficiently smooth settings, resulting...... in a general asymptotic bound. For compact convex sets with nowhere vanishing Gaussian curvature, the asymptotics can be described more explicitly. As in the case of volume estimators, the variance is decomposed into a lattice sum and an oscillating term of at most the same magnitude....

  2. Biosonar resolving power : echo-acoustic perception of surface structures in the submillimeter range

    NARCIS (Netherlands)

    Simon, Ralph; Knörnschild, Mirjam; Tschapka, Marco; Schneider, Annkathrin; Passauer, Nadine; Kalko, Elisabeth K V; von Helversen, Otto

    2014-01-01

    The minimum distance for which two points still can be separated from each other defines the resolving power of a visual system. In an echo-acoustic context, the resolving power is usually measured as the smallest perceivable distance of two reflecting surfaces on the range axis and is found to be

  3. Data transmission in long-range dielectric-loaded surface plasmon polariton waveguides

    DEFF Research Database (Denmark)

    Kharitonov, S.; Kiselev, R.; Kumar, Ashwani

    2014-01-01

    We demonstrate the data transmission of 10 Gbit/s on-off keying modulated 1550 nm signal through a long-range dielectric-loaded surface plasmon polariton waveguide structure with negligible signal degradation. In the experiment the bit error rate penalties do not exceed 0.6 dB over the 15 nm...

  4. Guiding of long-range surface plasmon polaritons along channels in periodic arrays of scatterers

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra; Hvam, Jørn Märcher; Nikolajsen, T.

    2004-01-01

    We investigate waveguiding of long-range surface plasmon polaritons in periodic arrays of scatterers at telecommunication wavelengths. A propagation loss of approximately 6 dB/mm and a coupling loss of 0.5 dB is reported for 8-ìm-wide channels....

  5. Range and geophysical corrections in coastal regions: and implications for mean sea surface determination

    DEFF Research Database (Denmark)

    Andersen, Ole Baltazar; Scharroo, Remko

    2011-01-01

    The determination of sea surface height from the altimeter range measurement involves a number of corrections: those expressing the behavior of the radar pulse through the atmosphere, and those correcting for sea state and other geophysical signals. A number of these corrections need special...

  6. Long-Range Forecasting of Surface Air Temperature and Precipitation for the Korean Peninsula

    Science.gov (United States)

    2013-03-01

    from the southeast area and Pusan (the second largest city in South Korea). The volcanic island of Cheju-do is located in the southern portion of this...highest correlation magnitude is to the northeast of Madagascar in the Indian Ocean. 35 Correlation of sea surface temperatures (SSTs) for Dec

  7. Positive or Negative? Urbanization-Induced Variations in Diurnal Skin-Surface Temperature Range Detected Using Satellite Data

    Science.gov (United States)

    Huang, Fan; Zhan, Wenfeng; Wang, Zhihua; Wang, Kaicun; Chen, Jing M.; Liu, Yongxue; Lai, Jiameng; Ju, Weimin

    2017-12-01

    Diurnal temperature range (DTR) is an important indicator for assessing the local climate change due to urbanization. Studies that focused on surface air temperature (SAT) have reported decreased DTRSAT in urban areas. However, this urbanization-induced effect becomes more complex with regard to land skin-surface temperature (LST), which is highly localized and extremely sensitive to land surface properties. We thus investigated the urban-rural DTRLST difference (ΔDTRLST) over 354 cities across China using satellite-retrieved LSTs within 2008-2013. Our major findings include the following: (1) urban areas experience increased (decreased) DTRLST compared with rural areas on the annual average for the majority of cities located in southern (northern) China; (2) the ΔDTRLST is mostly positive in warm months but negative in cold months. It generally becomes more positive from January to August and becomes more negative afterward; and (3) the ΔDTRLST is positively related to the daytime surface urban heat island intensity; it is yet negatively correlated with the urban-rural difference in vegetation abundance. We consider these insights valuable for in-depth understanding urban thermal environment and will likely help improve urban planning.

  8. Calibration Standards for Surface Topography Measuring Systems down to Nanometric Range

    DEFF Research Database (Denmark)

    Trumpold, H.; De Chiffre, Leonardo; Andreasen, Jan Lasson

    Background For the precise and accurate measurement of surface topography a whole range of surface detection systems is available. With their application in research and production problems arise due to the lack of traceable standard artefacts for the instrument calibration in X, Y and Z directions...... to be replicated during all stages of the replication processes. Procedures for cleaning glass, PVC, PC, PMM and Ni-surfaces have been developed and tested. Calibration procedures for calibration standards and for calibrating instruments in X-, Y- and Z-direction have been developed and tested. Proposals...... in industries ranging from automotive manufacture to ultraprecision manufacture of data storage systems and compact discs. Objectives The project is concerned with developing calibration standards including their production methods and calibration procedures as a consistent means of calibrating different types...

  9. Overcoming the reference large-area sources non-uniformity in surface area monitor calibration

    Energy Technology Data Exchange (ETDEWEB)

    Junior, Iremar Alves S.; Siqueira, Paulo de T.D.; Xavier, Marcs; Nascimento, Eduardo do; Potiens, Maria da Penha A., E-mail: iremarjr@usp.br, E-mail: ptsiquei@ipen.br, E-mail: mxavier@ipen.br, E-mail: eduardon@ufba.br, E-mail: mppalbu@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2015-07-01

    This paper describes a study using MCNP5 simulations, a Monte Carlo based radiation transport code, in order to evaluate the possibility of using reference large-area sources that do not meet the uniformity recommendations of the ISO 8769:2010 in surface contamination monitors calibration. {sup 14}C, {sup 36}Cl, {sup 99}Tc, {sup 137}Cs and {sup 90}Sr + {sup 90}Y large area reference sources were simulated as well as the setup and the detector probe. Simulations were carried out for both uniform and non-uniform surface distributions. In the case of uniform distribution, specific weights for each region were considered, as obtained in the uniformity evaluation measurements. To each simulation, it was considered the average number of signals generated in each detector probe, i.e., it was determined the fraction of stories depositing energy in the corresponding gas filled region of the detector. Simulations results show differences in detection efficiency values up to 15%. (author)

  10. Range 8C Rehabilitation Demonstration Project, Hohenfels Training Area, Germany: Final report

    International Nuclear Information System (INIS)

    Zellmer, S.D.; Hinchman, R.R.; Johnson, D.O.; Brent, J.J.

    1991-11-01

    More than 30 years of intensive and continual tactical training has caused extensive environmental damage at the US Army Hohenfels Training Area in Germany. The Range 8C Rehabilitation Demonstration Project, followed by a three-year monitoring effort, was conducted to develop and evaluate the environmental and economic effectiveness of seven revegetation and four erosion control prescriptions implemented at a 16-ha site. The point-intercept method was used to measure the types and amounts of vegetation established and the changes in the vegetative community during three years of military use on the seven areas treated with revegetation prescriptions. Field observations were made to determine the suitability and durability of four types of erosion control structures. Soil fertility and a source of seed appeared to be the most limiting factors in establishing vegetation, while seedbed preparation had only a minor influence. Grasses appeared to be more resistant to vehicle traffic than did other types of vegetation. Because grassed waterways were used as roads by military vehicles and a system of graded terraces was expensive, these erosion control prescriptions were unsuitable and uneconomical for use on training areas. Low-cost riprap waterbars and porous check dams slowed the velocity of runoff, trapped sediments, and were durable. Recommendations were formulated to improve the environmental and economic effectiveness of future rehabilitation efforts on tactical training areas

  11. Range 8C Rehabilitation Demonstration Project, Hohenfels Training Area, Germany: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Zellmer, S.D.; Hinchman, R.R.; Johnson, D.O. [Argonne National Lab., IL (United States). Energy Systems Div.; Severinghaus, W.D. [Corps of Engineers, Champaign, IL (United States); Brent, J.J. [Army Construction Engineering Research Lab., Champaign, IL (United States)

    1991-11-01

    More than 30 years of intensive and continual tactical training has caused extensive environmental damage at the US Army Hohenfels Training Area in Germany. The Range 8C Rehabilitation Demonstration Project, followed by a three-year monitoring effort, was conducted to develop and evaluate the environmental and economic effectiveness of seven revegetation and four erosion control prescriptions implemented at a 16-ha site. The point-intercept method was used to measure the types and amounts of vegetation established and the changes in the vegetative community during three years of military use on the seven areas treated with revegetation prescriptions. Field observations were made to determine the suitability and durability of four types of erosion control structures. Soil fertility and a source of seed appeared to be the most limiting factors in establishing vegetation, while seedbed preparation had only a minor influence. Grasses appeared to be more resistant to vehicle traffic than did other types of vegetation. Because grassed waterways were used as roads by military vehicles and a system of graded terraces was expensive, these erosion control prescriptions were unsuitable and uneconomical for use on training areas. Low-cost riprap waterbars and porous check dams slowed the velocity of runoff, trapped sediments, and were durable. Recommendations were formulated to improve the environmental and economic effectiveness of future rehabilitation efforts on tactical training areas.

  12. Error bounds for surface area estimators based on Crofton's formula

    DEFF Research Database (Denmark)

    Kiderlen, Markus; Meschenmoser, Daniel

    2009-01-01

    According to Crofton’s formula, the surface area S(A) of a sufficiently regular compact set A in R^d is proportional to the mean of all total projections pA (u) on a linear hyperplane with normal u, uniformly averaged over all unit vectors u. In applications, pA (u) is only measured in k directio...... in the sense that the relative error of the surface area estimator is very close to the minimal error....... and the mean is approximated by a finite weighted sum S(A) of the total projections in these directions. The choice of the weights depends on the selected quadrature rule. We define an associated zonotope Z (depending only on the projection directions and the quadrature rule), and show that the relative error...... S (A)/S (A) is bounded from below by the inradius of Z and from above by the circumradius of Z. Applying a strengthened isoperimetric inequality due to Bonnesen, we show that the rectangular quadrature rule does not give the best possible error bounds for d = 2. In addition, we derive asymptotic...

  13. Heavy metal contamination in surface runoff sediments of the urban area of Vilnius, Lithuania

    Directory of Open Access Journals (Sweden)

    Gytautas Ignatavičius

    2017-02-01

    Full Text Available Surface runoff from urbanized territories carries a wide range of pollutants. Sediments in untreated runoff from direct discharge stormwater systems significantly contribute to urban waterway pollution. In this study, heavy metal (Pb, Zn, Cu, Cr, Ba, As and Fe contamination in surface runoff sediments of the urban area of the city of Vilnius was investigated. The surface runoff sediment samples were collected from seven dischargers with the highest volume rate of water flow and concentrations of suspended solids. The geospatial analysis of the distribution of heavy metals shows that there are several active pollution sources supplying the dischargers with contaminated sediments. Most of these areas are located in the central part of the city and in old town with intense traffic. Principal components analysis and t-test results clearly depicted the significantly different chemical compositions of winter and autumn surface sediment samples. The sampling approach and assessment of results provide a useful tool to examine the contamination that is generated in urban areas, distinguish pollution sources and give a better understanding of the importance of permeable surfaces and green areas.

  14. Defining Indicators and Standards for Tourism Impacts in Protected Areas: Cape Range National Park, Australia

    Science.gov (United States)

    Moore, Susan A.; Polley, Amanda

    2007-03-01

    Visitors’ perceptions of impacts and acceptable standards for environmental conditions can provide essential information for the sustainable management of tourist destinations, especially protected areas. To this end, visitor surveys were administered during the peak visitor season in Cape Range National Park, on the northwest coast of Western Australia and adjacent to the iconic Ningaloo Reef. The central focus was visitors’ perceptions regarding environmental conditions and standards for potential indicators. Conditions considered of greatest importance in determining visitors’ quality of experience included litter, inadequate disposal of human waste, presence of wildlife, levels of noise, and access to beach and ocean. Standards were determined, based on visitors’ perceptions, for a range of site-specific and non-site-specific indicators, with standards for facilities (e.g., acceptable number of parking bays, signs) and for negative environmental impacts (e.g., levels of littering, erosion) sought. The proposed standards varied significantly between sites for the facilities indicators; however, there was no significant difference between sites for environmental impacts. For the facilities, the standards proposed by visitors were closely related to the existing situation, suggesting that they were satisfied with the status quo. These results are considered in the context of current research interest in the efficacy of visitor-derived standards as a basis for protected area management.

  15. Mesoscopic surface roughness of ice crystals pervasive across a wide range of ice crystal conditions

    Science.gov (United States)

    Magee, N. B.; Miller, A.; Amaral, M.; Cumiskey, A.

    2014-11-01

    Here we show high-magnification images of hexagonal ice crystals acquired by environmental scanning electron microscopy (ESEM). Most ice crystals were grown and sublimated in the water vapor environment of an FEI-Quanta-200 ESEM, but crystals grown in a laboratory diffusion chamber were also transferred intact and imaged via ESEM. All of these images display prominent mesoscopic topography including linear striations, ridges, islands, steps, peaks, pits, and crevasses; the roughness is not observed to be confined to prism facets. The observations represent the most highly magnified images of ice surfaces yet reported and expand the range of conditions in which rough surface features are known to be conspicuous. Microscale surface topography is seen to be ubiquitously present at temperatures ranging from -10 °C to -40 °C, in supersaturated and subsaturated conditions, on all crystal facets, and irrespective of substrate. Despite the constant presence of surface roughness, the patterns of roughness are observed to be dramatically different between growing and sublimating crystals, and transferred crystals also display qualitatively different patterns of roughness. Crystals are also demonstrated to sometimes exhibit inhibited growth in moderately supersaturated conditions following exposure to near-equilibrium conditions, a phenomenon interpreted as evidence of 2-D nucleation. New knowledge about the characteristics of these features could affect the fundamental understanding of ice surfaces and their physical parameterization in the context of satellite retrievals and cloud modeling. Links to supplemental videos of ice growth and sublimation are provided.

  16. Corrective Action Plan for Corrective Action Unit 407: Roller Coaster RADSAFE Area, Tonopah Test Range, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    T. M. Fitzmaurice

    2000-05-01

    This Corrective Action Plan (CAP) has been prepared for the Roller Coaster RADSAFE Area Corrective Action Unit 407 in accordance with the Federal Facility and Consent Order (Nevada Division of Environmental Protection [NDEP] et al., 1996). This CAP provides the methodology for implementing the approved Corrective Action Alternative as listed in the Corrective Action Decision Document (U.S. Department of Energy, Nevada Operations Office, 1999). The RCRSA was used during May and June of 1963 to decontaminate vehicles, equipment, and personnel from the Clean Slate tests. The Constituents of Concern (COCs) identified during the site characterization include plutonium, uranium, and americium. No other COCS were identified. The following closure actions will be implemented under this plan: (1) Remove and dispose of surface soils which are over three times background for the area. Soils identified for removal will be disposed of at an approved disposal facility. Excavated areas will be backfilled with clean borrow soil fi-om a nearby location. (2) An engineered cover will be constructed over the waste disposal pit area where subsurface COCS will remain. (3) Upon completion of the closure and approval of the Closure Report by NDEP, administrative controls, use restrictions, and site postings will be used to prevent intrusive activities at the site. Barbed wire fencing will be installed along the perimeter of this unit. Post closure monitoring will consist of site inspections to determine the condition of the engineered cover. Any identified maintenance and repair requirements will be remedied within 90 working days of discovery and documented in writing at the time of repair. Results of all inspections/repairs for a given year will be addressed in a single report submitted annually to the NDEP.

  17. Measurement range of phase retrieval in optical surface and wavefront metrology

    International Nuclear Information System (INIS)

    Brady, Gregory R.; Fienup, James R.

    2009-01-01

    Phase retrieval employs very simple data collection hardware and iterative algorithms to determine the phase of an optical field. We have derived limitations on phase retrieval, as applied to optical surface and wavefront metrology, in terms of the speed of beam (i.e., f-number or numerical aperture) and amount of aberration using arguments based on sampling theory and geometrical optics. These limitations suggest methodologies for expanding these ranges by increasing the complexity of the measurement arrangement, the phase-retrieval algorithm, or both. We have simulated one of these methods where a surface is measured at unusual conjugates

  18. Addressing Spatial Variability of Surface-Layer Wind with Long-Range WindScanners

    DEFF Research Database (Denmark)

    Berg, Jacob; Vasiljevic, Nikola; Kelly, Mark C.

    2015-01-01

    This paper presents an analysis of mean wind measurements from a coordinated system of long-range WindScanners. From individual scan patterns the mean wind field was reconstructed over a large area, and hence it highlights the spatial variability. From comparison with sonic anemometers, the quality...

  19. High-Surface-Area Porous Platinum Electrodes for Enhanced Charge Transfer

    OpenAIRE

    Hu Yelin; Yella Aswani; Guldin Stefan; Schreier Marcel; Stellacci Francesco; Grätzel Michael; Stefik Morgan

    2014-01-01

    Cobalt based electrolytes are highly tunable and have pushed the limits of dye sensitized solar cells enabling higher open circuit voltages and new record effi ciencies. However the performance of these electrolytes and a range of other electrolytes suffer from slow electron transfer at platinum counter electrodes. High surface area platinum would enhance catalysis but pure platinum structures are too expensive in practice. Here a material effi cient host guest architecture is developed that ...

  20. Method for producing high surface area chromia materials for catalysis

    Science.gov (United States)

    Gash, Alexander E [Brentwood, CA; Satcher, Joe [Patterson, CA; Tillotson, Thomas [Tracy, CA; Hrubesh, Lawrence [Pleasanton, CA; Simpson, Randall [Livermore, CA

    2007-05-01

    Nanostructured chromium(III)-oxide-based materials using sol-gel processing and a synthetic route for producing such materials are disclosed herein. Monolithic aerogels and xerogels having surface areas between 150 m.sup.2/g and 520 m.sup.2/g have been produced. The synthetic method employs the use of stable and inexpensive hydrated-chromium(III) inorganic salts and common solvents such as water, ethanol, methanol, 1-propanol, t-butanol, 2-ethoxy ethanol, and ethylene glycol, DMSO, and dimethyl formamide. The synthesis involves the dissolution of the metal salt in a solvent followed by an addition of a proton scavenger, such as an epoxide, which induces gel formation in a timely manner. Both critical point (supercritical extraction) and atmospheric (low temperature evaporation) drying may be employed to produce monolithic aerogels and xerogels, respectively.

  1. Fully automated algorithm for wound surface area assessment.

    Science.gov (United States)

    Deana, Alessandro Melo; de Jesus, Sérgio Henrique Costa; Sampaio, Brunna Pileggi Azevedo; Oliveira, Marcelo Tavares; Silva, Daniela Fátima Teixeira; França, Cristiane Miranda

    2013-01-01

    Worldwide, clinicians, dentists, nurses, researchers, and other health professionals need to monitor the wound healing progress and to quantify the rate of wound closure. The aim of this study is to demonstrate, step by step, a fully automated numerical method to estimate the size of the wound and the percentage damaged relative to the body surface area (BSA) in images, without the requirement for human intervention. We included the formula for BSA in rats in the algorithm. The methodology was validated in experimental wounds and human ulcers and was compared with the analysis of an experienced pathologist, with good agreement. Therefore, this algorithm is suitable for experimental wounds and burns and human ulcers, as they have a high contrast with adjacent normal skin. © 2013 by the Wound Healing Society.

  2. Electromagnetic surface waves for large-area RF plasma productions between large-area planar electrodes

    International Nuclear Information System (INIS)

    Nonaka, S.

    1992-01-01

    Recently, large-area plasma production has been tested by means of a 13.56 MHz radio-frequency (RF) discharge between a pair of large-area planar electrodes, approximately 0.5 m x 1.4 m, as one of the semiconductor technologies for fabrication of large-area amorphous silicon solar cells in the ''Sunshine Project'' of the Agency of Industrial Science and Technology in Japan. We also confirmed long plasma production between a pair of long electrodes. In this paper, normal electromagnetic (EM) waves propagating in a region between a planar waveguide with one plasma and two dielectric layers are analyzed in order to study the feasibility of large-area plasma productions by EM wave-discharges between a pair of large-area RF electrodes larger than the half-wavelength of RF wave. In conclusion, plasmas higher than an electron plasma frequency will be produced by an odd TMoo surface mode. (author) 4 refs., 3 figs

  3. Sensing of bacteria immobilised under static conditions using long-range surface plasmon waveguides in Cytop

    Science.gov (United States)

    Khan, Asad; Krupin, Oleksiy; Lisicka-Skrzek, Ewa; Berini, Pierre

    2011-08-01

    Waveguides consisting of Au embedded in Cytop with micro-fluidic channels etched into the cladding are used for sensing via the propagation of long-range surface plasmons. Initially, a range of water/glycerol solutions with varying refractive indices were sequentially injected in a waveguide section in order to assess its bulk sensitivity and to find a solution supporting a strong high quality mode. Au waveguide surfaces were then functionalized with antibodies against Gram negative bacteria (Anti-Gneg) by first forming a self-assembled monolayer (SAM) of 16-mercaptohexadecanoic acid (16-MHA) and subsequent conjugation with antibodies through carbodiimide chemistry. E.Coli XL-1 Blue was used as an analyte in static incubations. Wavelength sweeps of 16-MHA covered waveguides were compared against waveguides covered with E-coli. The results indicate that very few bacteria cells are required to obtain a measurable change in output signal.

  4. Human cortical areas involved in perception of surface glossiness.

    Science.gov (United States)

    Wada, Atsushi; Sakano, Yuichi; Ando, Hiroshi

    2014-09-01

    Glossiness is the visual appearance of an object's surface as defined by its surface reflectance properties. Despite its ecological importance, little is known about the neural substrates underlying its perception. In this study, we performed the first human neuroimaging experiments that directly investigated where the processing of glossiness resides in the visual cortex. First, we investigated the cortical regions that were more activated by observing high glossiness compared with low glossiness, where the effects of simple luminance and luminance contrast were dissociated by controlling the illumination conditions (Experiment 1). As cortical regions that may be related to the processing of glossiness, V2, V3, hV4, VO-1, VO-2, collateral sulcus (CoS), LO-1, and V3A/B were identified, which also showed significant correlation with the perceived level of glossiness. This result is consistent with the recent monkey studies that identified selective neural response to glossiness in the ventral visual pathway, except for V3A/B in the dorsal visual pathway, whose involvement in the processing of glossiness could be specific to the human visual system. Second, we investigated the cortical regions that were modulated by selective attention to glossiness (Experiment 2). The visual areas that showed higher activation to attention to glossiness than that to either form or orientation were identified as right hV4, right VO-2, and right V3A/B, which were commonly identified in Experiment 1. The results indicate that these commonly identified visual areas in the human visual cortex may play important roles in glossiness perception. Copyright © 2014. Published by Elsevier Inc.

  5. Assessment of Surface Area Characteristics of Dental Implants with Gradual Bioactive Surface Treatment

    Science.gov (United States)

    Czan, Andrej; Babík, Ondrej; Miklos, Matej; Záušková, Lucia; Mezencevová, Viktória

    2017-10-01

    Since most of the implant surface is in direct contact with bone tissue, shape and integrity of said surface has great influence on successful osseointegration. Among other characteristics that predetermine titanium of different grades of pureness as ideal biomaterial, titanium shows high mechanical strength making precise miniature machining increasingly difficult. Current titanium-based implants are often anodized due to colour coding. This anodized layer has important functional properties for right usage and also bio-compatibility of dental implants. Physical method of anodizing and usage of anodizing mediums has a significant influence on the surface quality and itself functionality. However, basic requirement of the dental implant with satisfactory properties is quality of machined surface before anodizing. Roughness, for example, is factor affecting of time length of anodizing operation and so whole productivity. The paper is focused on monitoring of surface and area characteristics, such as roughness or surface integrity after different cutting conditions of miniature machining of dental implants and their impact on suitability for creation of satisfactory anodized layer with the correct biocompatible functional properties.

  6. Surface ozone in the urban area of Manaus, Amazonas, Brazil

    Science.gov (United States)

    Souza, R. A. F. D.; Costa, P. S.; Silva, C.; Godoi, R. M.; Martin, S. T.; Tota, J.; Barbosa, H. M.; Pauliquevis, T.; Ferreira De Brito, J.; Artaxo, P.; Manzi, A. O.; Wolf, S. A.; Cirino, G. G.

    2014-12-01

    When nitrogen oxides from vehicle and industrial emissions mix with volatile organic compounds from trees and plants with exposure to sunlight, a chemical reaction occurs contributing to ground-level ozone pollution. The preliminary results of the surface ozone study in urban area of Manaus, Amazonas State, Brazil, are presented for the first intensive operating period (IOP1) of the GoAmazon experiment (February/March 2014). Photochemical ozone production was found to be a regular process, with an afternoon maximum of the ozone mixing ratio of lower than 20 ppbv for cloudy days or clear sky weather. Typical ozone concentrations at mid-day were low (about 10 ppb). On the other hand, several high-value ozone episodes with surface ozone mixing ratios up to three times larger were registered during the dry season of 2013 (September/October). At the beginning of the wet season, the ozone concentration in Manaus decreased significantly, but diurnal variations can be found during the days with rainfall and other fast changes of meteorological conditions. Possible explanations of the nature of pulsations are discussed. Photochemical ozone production by local urban plumes of Manaus is named as a first possible source of the ozone concentration and biomass burning or power plant emissions are suggested as an alternative or an additional source.

  7. The dependence of the nuclear charge form factor on short range correlations and surface fluctuation effects

    International Nuclear Information System (INIS)

    Massen, S. E.; Garistov, V. P.; Grypeos, M. E.

    1996-01-01

    The effects of nuclear surface fluctuations on harmonic oscillator elastic charge form factor of light nuclei are investigated, simultaneously approximating the short-range correlations through a Jastrow correlation factor. Inclusion of the surface fluctuation effects within this description, by truncating the cluster expansion at the two-body part, is found to improve somewhat the fit to the elastic charge form-factor of 16 O and 40 Ca. However, the convergence of the cluster expansion is expected to deteriorate. An additional finding is that surface-fluctuation correlations produce a drastic change in the asymptotic behaviour of the point-proton form-factor, which now falls off quite slowly (i.e. as const.q -4 ) at large values of the momentum transfer q

  8. Conceptual Model for the Transport of Energetic Residues from Surface Soil to Groundwater by Range Activities

    Science.gov (United States)

    2006-11-01

    fluidized - bed reactors. Although engineered biological reduction of per- chlorate for drinking water has been demonstrated, the application of this...Hence, slow transport of TNT from the soil bed is a limiting fac- tor in the phytoremediation or bioremediation of TNT. Fluxes were, in de- creasing...for RDX and HMX were estimated using mass-to-surface-area ratios for each ex- plosive based on military specifications for acceptable granulation

  9. Estimating the surface area of birds: using the homing pigeon (Columba livia as a model

    Directory of Open Access Journals (Sweden)

    Cristina R. Perez

    2014-05-01

    Full Text Available Estimation of the surface area of the avian body is valuable for thermoregulation and metabolism studies as well as for assessing exposure to oil and other surface-active organic pollutants from a spill. The use of frozen carcasses for surface area estimations prevents the ability to modify the posture of the bird. The surface area of six live homing pigeons in the fully extended flight position was estimated using a noninvasive method. An equation was derived to estimate the total surface area of a pigeon based on its body weight. A pigeon's surface area in the fully extended flight position is approximately 4 times larger than the surface area of a pigeon in the perching position. The surface area of a bird is dependent on its physical position, and, therefore, the fully extended flight position exhibits the maximum area of a bird and should be considered the true surface area of a bird.

  10. NEW CONCEPTS AND TEST METHODS OF CURVE PROFILE AREA DENSITY IN SURFACE: ESTIMATION OF AREAL DENSITY ON CURVED SPATIAL SURFACE

    OpenAIRE

    Hong Shen

    2011-01-01

    The concepts of curve profile, curve intercept, curve intercept density, curve profile area density, intersection density in containing intersection (or intersection density relied on intersection reference), curve profile intersection density in surface (or curve intercept intersection density relied on intersection of containing curve), and curve profile area density in surface (AS) were defined. AS expressed the amount of curve profile area of Y phase in the unit containing surface area, S...

  11. Moving to 3D: relationships between coral planar area, surface area and volume.

    Science.gov (United States)

    House, Jenny E; Brambilla, Viviana; Bidaut, Luc M; Christie, Alec P; Pizarro, Oscar; Madin, Joshua S; Dornelas, Maria

    2018-01-01

    Coral reefs are a valuable and vulnerable marine ecosystem. The structure of coral reefs influences their health and ability to fulfill ecosystem functions and services. However, monitoring reef corals largely relies on 1D or 2D estimates of coral cover and abundance that overlook change in ecologically significant aspects of the reefs because they do not incorporate vertical or volumetric information. This study explores the relationship between 2D and 3D metrics of coral size. We show that surface area and volume scale consistently with planar area, albeit with morphotype specific conversion parameters. We use a photogrammetric approach using open-source software to estimate the ability of photogrammetry to provide measurement estimates of corals in 3D. Technological developments have made photogrammetry a valid and practical technique for studying coral reefs. We anticipate that these techniques for moving coral research from 2D into 3D will facilitate answering ecological questions by incorporating the 3rd dimension into monitoring.

  12. Strong and tough cellulose nanopaper with high specific surface area and porosity.

    Science.gov (United States)

    Sehaqui, Houssine; Zhou, Qi; Ikkala, Olli; Berglund, Lars A

    2011-10-10

    In order to better understand nanostructured fiber networks, effects from high specific surface area of nanofibers are important to explore. For cellulose networks, this has so far only been achieved in nonfibrous regenerated cellulose aerogels. Here, nanofibrillated cellulose (NFC) is used to prepare high surface area nanopaper structures, and the mechanical properties are measured in tensile tests. The water in NFC hydrogels is exchanged to liquid CO2, supercritical CO2, and tert-butanol, followed by evaporation, supercritical drying, and sublimation, respectively. The porosity range is 40-86%. The nanofiber network structure in nanopaper is characterized by FE-SEM and nitrogen adsorption, and specific surface area is determined. High-porosity TEMPO-oxidized NFC nanopaper (56% porosity) prepared by critical point drying has a specific surface area as high as 482 m(2) g(-1). The mechanical properties of this nanopaper structure are better than for many thermoplastics, but at a significantly lower density of only 640 kg m(-3). The modulus is 1.4 GPa, tensile strength 84 MPa, and strain-to-failure 17%. Compared with water-dried nanopaper, the material is softer with substantiallly different deformation behavior.

  13. Economic susceptibility of fire-prone landscapes in natural protected areas of the southern Andean Range.

    Science.gov (United States)

    Molina, Juan Ramón; Moreno, Roberto; Castillo, Miguel; Rodríguez Y Silva, Francisco

    2018-04-01

    Large fires are the most important disturbances at landscape-level due to their ecological and socioeconomic impacts. This study aimed to develop an approach for the assessment of the socio-economic landscape susceptibility to fire. Our methodology focuses on the integration of economic components of landscape management based on contingent valuation method (CVM) and net-value change (NVC). This former component has been estimated using depreciation rates or changes on the number of arrivals to different natural protected areas after a large fire occurrence. Landscape susceptibility concept has been motivated by the need to assist fire prevention programs and environmental management. There was a remarkable variation in annual economic value attributed to each protected area based on the CVM scenario, ranging from 40,189-46,887$/year ("Tolhuaca National Park") to 241,000-341,953$/year ("Conguillio National Park"). We added landscape susceptibility using depreciation rates or tourist arrival decrease which varied from 2.04% (low fire intensity in "Tolhuaca National Park") to 76.67% (high fire intensity in "Conguillio National Park"). The integration of this approach and future studies about vegetation resilience should seek management strategies to increase economic efficiency in the fire prevention activities. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Documentation of the Range 8C rehabilitation demonstration project at Hohenfels Training Area, West Germany

    Energy Technology Data Exchange (ETDEWEB)

    Zellmer, S.D.; Hinchman, R.R.; Carter, R.P.; Severinghaus, W.D.; Lacey, R.M.; Brent, J.J.

    1987-03-01

    Continued and intensive tactical training for the last 35 years at the Hohenfels Training Area (HTA), Federal Republic of Germany, has resulted in extensive environmental damage and reduced training realism. The US Corps of Engineers Construction Engineering Research Laboratory is developing an Integrated Training Area Management (ITAM) Program for the Seventh Army Training Command for use at HTA. Argonne National Laboratory was asked to assist in one element of the ITAM program, a training range rehabilitation demonstration project. The rehabilitation project was begun in 1986 on a 62-ha watershed that included about 16 ha of meadow with training damage typical of HTA. On the basis of amount of plant ground cover, type and degree of erosion, and soil properties, 10 rehabilitation prescriptions were developed to reestablish plant cover, control erosion, and improve training realism. Prescriptions were installed by a local contractor in September 1986. A monitoring program is under way to determine the effectiveness of this effort. Results and experience gained from this project will be used in the ITAM program and for rehabilitation training courses conducted at HTA.

  15. Strategies for leukemic biomarker detection using long-range surface plasmon-polaritons

    Science.gov (United States)

    Krupin, O.; Wang, C.; Berini, P.

    2014-09-01

    The suitability and use of long-range surface plasmon-polaritons for leukemic biomarker detection is discussed. A novel optical biosensor comprised of gold straight waveguides embedded in CYTOP with an etched microfluidic channel was tested for detecting leukemia in patient serum. Gold surface functionalization involved the interaction of protein G (PG) with antibodies by first adsorbing PG on bare gold and then antibodies (Immunoglobulin G, IgG). Differentiation between healthy and leukemia patients was based on the difference in ratios of Ig kappa (Igκ) and Ig lambda (Igλ) light chains in both serums. The ratio for a normal patient is ~1.4 - 2, whereas for a leukemia patient this ratio is altered. As a receptor (primary antibodies), goat anti-human anti-IgGκ and anti-IgGλ were used to functionalize the surface. Diluted normal and leukemia patient serums were tested over the aforementioned surfaces. The ratios of mass surface densities of IgGκ:IgGλ for normal serum (NS) and patient serum (PS) were found to be 1.55 and 1.92 respectively.

  16. Large area optical mapping of surface contact angle.

    Science.gov (United States)

    Dutra, Guilherme; Canning, John; Padden, Whayne; Martelli, Cicero; Dligatch, Svetlana

    2017-09-04

    Top-down contact angle measurements have been validated and confirmed to be as good if not more reliable than side-based measurements. A range of samples, including industrially relevant materials for roofing and printing, has been compared. Using the top-down approach, mapping in both 1-D and 2-D has been demonstrated. The method was applied to study the change in contact angle as a function of change in silver (Ag) nanoparticle size controlled by thermal evaporation. Large area mapping reveals good uniformity for commercial Aspen paper coated with black laser printer ink. A demonstration of the forensic and chemical analysis potential in 2-D is shown by uncovering the hidden CsF initials made with mineral oil on the coated Aspen paper. The method promises to revolutionize nanoscale characterization and industrial monitoring as well as chemical analyses by allowing rapid contact angle measurements over large areas or large numbers of samples in ways and times that have not been possible before.

  17. Dynamic characterisation of the specific surface area for fracture networks

    Science.gov (United States)

    Cvetkovic, V.

    2017-12-01

    One important application of chemical transport is geological disposal of high-level nuclear waste for which crystalline rock is a prime candidate for instance in Scandinavia. Interconnected heterogeneous fractures of sparsely fractured rock such as granite, act as conduits for transport of dissolved tracers. Fluid flow is known to be highly channelized in such rocks. Channels imply narrow flow paths, adjacent to essentially stagnant water in the fracture and/or the rock matrix. Tracers are transported along channelised flow paths and retained by minerals and/or stagnant water, depending on their sorption properties; this mechanism is critical for rocks to act as a barrier and ultimately provide safety for a geological repository. The sorbing tracers are retained by diffusion and sorption on mineral surfaces, whereas non-sorbing tracers can be retained only by diffusion into stagnant water of fractures. The retention and transport properties of a sparsely fractured rock will primarily depend on the specific surface area (SSA) of the fracture network which is determined by the heterogeneous structure and flow. The main challenge when characterising SSA on the field-scale is its dependence on the flow dynamics. We first define SSA as a physical quantity and clarify its importance for chemical transport. A methodology for dynamic characterisation of SSA in fracture networks is proposed that relies on three sets of data: i) Flow rate data as obtained by a flow logging procedure; ii) transmissivity data as obtained by pumping tests; iii) fracture network data as obtained from outcrop and geophysical observations. The proposed methodology utilises these data directly as well as indirectly through flow and particle tracking simulations in three-dimensional discrete fracture networks. The methodology is exemplified using specific data from the Swedish site Laxemar. The potential impact of uncertainties is of particular significance and is illustrated for radionuclide

  18. Biosonar resolving power: Echo-acoustic perception of surface structures in the submillimeter range

    Directory of Open Access Journals (Sweden)

    Ralph eSimon

    2014-02-01

    Full Text Available The minimum distance for which two points still can be separated from each other defines the resolving power of a visual system. In an echo-acoustic context, the resolving power is usually measured as the smallest perceivable distance of two reflecting surfaces on the range axis and is found to be around half a millimetre for bats employing frequency modulated echolocation calls. Only few studies measured such thresholds with physical objects, most often bats were trained on virtual echoes i.e. echoes generated and played back by a computer; moreover, bats were sitting while they received the stimuli. In these studies differences in structure depth between 200 µm and 340 µm were found. However, these low thresholds were never verified for free-flying bats and real physical objects. Here, we show behavioural evidence that the echo-acoustic resolving power for surface structures in fact can be as low as measured for computer generated echoes and even lower, sometimes below 100 µm. We found this exceptional fine discrimination ability only when one of the targets showed spectral interferences in the frequency range of the bats' echolocation call while the other target did not. This result indicates that surface structure is likely to be perceived as a spectral quality rather than being perceived strictly in the time domain. Further, it points out that sonar resolving power directly depends on the highest frequency/shortest wavelength of the signal employed.

  19. Mass movements of lowland areas in long range TLS and ALS monitoring

    Science.gov (United States)

    Tyszkowski, Sebastian

    2015-04-01

    The development of geodynamic processes in lowland areas remains an interesting issue for geomorphology and geology as well as civil engineering. Landslides, slumps, slope washes, rills and gully erosion are considered both geomorphological processes and natural hazards. In order to know precisely their origin and development, it is crucial to determine the rate and direction of their change. Previously such studies used geodesy and photogrammetry but the recent progress in the LiDAR technology allows collecting the data in a wider range and comparable or higher precision than most of geodetic methods. Airborne Laser Scanning (ALS) is also a good tool, but high costs and low frequency of the surveys make it difficult to trace the dynamics of the studied phenomena and processes. Nevertheless, this method enables gathering information from large areas, which is useful for the preliminary identification of the research issues and nomination of the areas for subsequent case studies. It is, however, more common to use Terrestrial Laser Scanning (TLS) for the detailed studies of morphology and its change. This method provides mobility and high accuracy, and enables frequent measurements. The problem in the analysis of many geoprocesses lies in the limited range of this method. This study concerns the Lower Vistula Valley located in northern Poland. It presents the results of measurements of landslides located in the escarpment zone of a big river valley. The object of the studies is mass movements developing within the quaternary deposits on the valley slopes. These processes were monitored in previous years with the traditional survey methods, mainly based on the geodesy field observations (benchmark) as well as the analyses of historical maps and archives. The ALS method used during the study enabled gathering the data on the valley with the density of 8 points per sq m, which provided the background for the consecutive monitoring study. In the surveys a terrestrial

  20. Long-range attractive forces extending from the alumina’s nanolayer surface in aqueous solutions

    Directory of Open Access Journals (Sweden)

    Leonid A. Kaledin

    2015-07-01

    Full Text Available Aluminum oxide-hydroxide nanolayer with a thickness of approximately 1.2 nm is electroadhesively deposited onto silicious support material with large surface area of about 50 m2/g, forming a highly electropositive composite of boehmite nanolayer in the form of monocrystalline oxide/hydroxide (α-Al2O3·H2O on the second electronegative solid. The composite can be viewed as a sphere with a rough surface and charge density of approximately 0.08 C/m2. This creates a significant electric field with negligible screening (ka ≪ 1 in the region close to the surface of the nanocomposite. This field attracts nano- and micron-sized particles from as far as 200 μm in a few seconds, many orders of magnitude greater than conventional Derjaguin–Landau–Verwey–Overbeek (DLVO theory, which predicts only nanometer-scale effects arising from the presence of the surface. The strong electric field on the surface is then able to retain small particles such as viruses, atomically thin sheets of graphene oxide, RNA, DNA, proteins, dyes as well as heavy metals such as cobalt, arsenic, and lead. Alumina’s nanolayer surface can be further functionalized by adding other sub-micron or nano-sized particles to target a specific contaminant. An example is shown where alumina nanolayer is coated with nano-sized iron monohydrate to yield an arsenic sorbent that shows high sorption capacity.

  1. Characteristics of PAHs adsorbed on street dust and the correlation with specific surface area and TOC.

    Science.gov (United States)

    Wang, Chengkun; Li, Yingxia; Liu, Jingling; Xiang, Li; Shi, Jianghong; Yang, Zhifeng

    2010-10-01

    Street dust was collected from five roads with different traffic volumes in the metropolitan area of Beijing and separated into five size fractions. Concentrations of polycyclic aromatic hydrocarbons (PAHs) adsorbed on street dust in different size ranges and their correlation with specific surface area and total organic carbon (TOC) were investigated. Results show that the concentration of 16-PAHs of sieved samples ranges from 0.27 to 1.30 mg/kg for all the sampling sites. Particles smaller than 40 mum in diameter have the highest 16-PAHs concentration among all of the size ranges for street dust from the four sampling sites with vehicles running on. PAHs with three or four rings account for 68% of the overall 16-PAHs on average. Remarkable positive correlation exists between 16-PAHs concentration and specific surface area with R(2) values from 0.7 to 0.96 for the four sampling sites with vehicles running on. The relationship between the concentration of 16-PAHs and TOC is less clear.

  2. Surface Rupture Effects on Earthquake Moment-Area Scaling Relations

    Science.gov (United States)

    Luo, Yingdi; Ampuero, Jean-Paul; Miyakoshi, Ken; Irikura, Kojiro

    2017-09-01

    Empirical earthquake scaling relations play a central role in fundamental studies of earthquake physics and in current practice of earthquake hazard assessment, and are being refined by advances in earthquake source analysis. A scaling relation between seismic moment ( M 0) and rupture area ( A) currently in use for ground motion prediction in Japan features a transition regime of the form M 0- A 2, between the well-recognized small (self-similar) and very large (W-model) earthquake regimes, which has counter-intuitive attributes and uncertain theoretical underpinnings. Here, we investigate the mechanical origin of this transition regime via earthquake cycle simulations, analytical dislocation models and numerical crack models on strike-slip faults. We find that, even if stress drop is assumed constant, the properties of the transition regime are controlled by surface rupture effects, comprising an effective rupture elongation along-dip due to a mirror effect and systematic changes of the shape factor relating slip to stress drop. Based on this physical insight, we propose a simplified formula to account for these effects in M 0- A scaling relations for strike-slip earthquakes.

  3. Analysis of the Impact of Wildfire on Surface Ozone Record in the Colorado Front Range

    Science.gov (United States)

    McClure-Begley, A.; Petropavlovskikh, I. V.; Oltmans, S. J.; Pierce, R. B.; Sullivan, J. T.; Reddy, P. J.

    2015-12-01

    Ozone plays an important role on the oxidation capacity of the atmosphere, and at ground-level has negative impacts on human health and ecosystem processes. In order to understand the dynamics and variability of surface ozone, it is imperative to analyze individual sources, interactions between sources, transport, and chemical processes of ozone production and accumulation. Biomass burning and wildfires have been known to emit a suite of particulate matter and gaseous compounds into the atmosphere. These compounds, such as, volatile organic compounds, carbon monoxide, and nitrogen oxides are precursor species which aid in the photochemical production and destruction of ozone. The Colorado Front Range (CFR) is a region of complex interactions between pollutant sources and meteorological conditions which result in the accumulation of ozone. High ozone events in the CFR associated with fires are analyzed for 2003-2014 to develop understanding of the large scale influence and variability of ozone and wildfire relationships. This study provides analysis of the frequency of enhanced ozone episodes that can be confirmed to be transported within and affected by the fires and smoke plumes. Long-term records of surface ozone data from the CFR provide information on the impact of wildfire pollutants on seasonal and diurnal ozone behavior. Years with increased local fire activity, as well as years with increased long-range transport of smoke plumes, are evaluated for the effect on the long-term record and high ozone frequency of each location. Meteorological data, MODIS Fire detection images, NOAA HYSPLIT Back Trajectory analysis, NOAA Smoke verification model, Fire Tracer Data (K+), RAQMS Model, Carbon Monoxide data, and Aerosol optical depth retrievals are used with NOAA Global Monitoring Division surface ozone data from three sites in Colorado. This allows for investigation of the interactions between pollutants and meteorology which result in high surface ozone levels.

  4. Effect of perfusate hematocrit on urea permeability-surface area in isolated dog lung

    International Nuclear Information System (INIS)

    Parker, R.E.; Roselli, R.J.; Haselton, F.R.; Harris, T.R.

    1986-01-01

    Seven dog lower left lung lobes were statically inflated and perfused at a constant rate for each lobe with a perfusate in which the hematocrit was altered over a wide range. The permeability-surface area of urea was calculated from multiple indicator dilution curves using two separate injectates for each hematocrit level. One injectate contained only 125 I-albumin as the vascular reference tracer and the other contained both 51 Cr-erythrocytes and 125 I-albumin as the vascular reference tracers; both contained [ 14 C]urea as the permeating tracer. The results strongly indicate that the phenomenon of erythrocyte trapping of urea does not affect the calculation of urea permeability-surface area product provided the appropriate albumin-erythrocyte composite reference tracer is utilized in its calculation

  5. Propagation of long-range surface plasmon polaritons in photonic crystals

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra; Søndergaard, Thomas; Nikolajsen, T.

    2005-01-01

    We study the interaction of long-range surface plasmon polaritons (LR-SPPs), excited at telecommunication wavelengths, with photonic crystals (PCs) formed by periodic arrays of gold bumps that are arranged in a triangular lattice and placed symmetrically on both sides of a thin gold film embedded...... structures, is rather weak, so that the photonic bandgap effect might be expected to take place only for some particular propagation directions. Preliminary experiments on LR-SPP bending and splitting at large angles are reported, and further research directions are discussed....

  6. Long-range surface-plasmon-polariton excitation at the quantum level

    International Nuclear Information System (INIS)

    Ballester, D.; Tame, M. S.; Kim, M. S.; Lee, C.; Lee, J.

    2009-01-01

    We provide the quantum-mechanical description of the excitation of long-range surface-plasmon polaritons (LRSPPs) on thin metallic strips. The excitation process consists of an attenuated-reflection setup, where efficient photon-to-LRSPP wave-packet transfer is shown to be achievable. For calculating the coupling, we derive the first quantization of LRSPPs in the polaritonic regime. We study quantum statistics during propagation and characterize the performance of photon-to-LRSPP quantum state transfer for single-photons, photon-number states, and photonic coherent superposition states.

  7. Propagation of long-range surface plasmon polaritons in photonic crystals

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra; Søndergaard, Thomas; Nikolajsen, T.

    2005-01-01

    We study the interaction of long-range surface plasmon polaritons (LR-SPPs), excited at telecommunication wavelengths, with photonic crystals (PCs) formed by periodic arrays of gold bumps that are arranged in a triangular lattice and placed symmetrically on both sides of a thin gold film embedded......) into the investigated PC structures. Using a self-consistent description based on the Green'S function formalism, we simulate numerically the LR-SPP transmission through and reflection from finite-size PC structures consisting of finite-size scatterers, as well as the LR-SPP guiding along line defects...

  8. Compact Z-add-drop wavelength filters for long-range surface plasmon polaritons

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra; Bozhevolnyi, Sergey I.; Søndergaard, Thomas

    2005-01-01

    We design, fabricate and investigate compact Z-add-drop (ZAD) filters for long-range surface plasmon polaritons (LR-SPPs) at telecom wavelengths. The ZAD filter for LR-SPPs consists of two ridge gratings formed by periodic gold thickness modulation at the intersections of three zigzag-crossed gold...... stripes embedded in polymer. We investigate influence of the grating length and crossing angle on the filter characteristics and demonstrate a 10o-ZAD filter based on 80-mm-long gratings that exhibit a 15-dB dip (centered at ~1.55 mm) in transmission of the direct arm along with the corresponding ~13-nm...

  9. 75 FR 27286 - McKelvie Geographic Area Range Allotment Management Planning on the Samuel R. McKelvie National...

    Science.gov (United States)

    2010-05-14

    ... Geographic Area, Samuel R. McKelvie National Forest, Bessey Ranger District in Nebraska. The original notice... allotments within the McKelvie Geographic Area on the McKelvie National Forest and analyze continuation of... Forest Service McKelvie Geographic Area Range Allotment Management Planning on the Samuel R. McKelvie...

  10. 30 CFR 912.764 - Process for designating areas unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... surface coal mining operations. 912.764 Section 912.764 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE IDAHO § 912.764 Process for designating areas unsuitable for surface coal mining... coal mining and reclamation operations. ...

  11. Surface accuracy of a large-scale compact antenna test range considering mechanism, metrology and alignment

    International Nuclear Information System (INIS)

    Zhou, Guofeng; Li, Xiaoxing; Li, Dongsheng; Luan, Jingdong; Zhao, Jinze

    2014-01-01

    A large compact range (CR) having a width of 23 m and height of 16 m that will generate a Φ15 m quiet zone is presented. The antenna consists of 30 blocks and 76 serrated reflectors. Its mechanical accuracy is reflected in two aspects: surface precision and gap precision. In addition, the root-mean-square (RMS) surface accuracy should be less than or equal to 0.075 mm for achieving the highest operating frequency of 40 GHz, and the gaps between two segments should be controlled strictly to the tolerance of 0.4 ± 0.2 mm for avoiding gap diffraction and compensating for inter-block interference due to thermal deformation. The surface accuracy in terms of mechanical structure, metrology and alignment approach is very tight. First, a high-accuracy honeycomb sandwich panel, anisotropic back structure and spatial parallel adjustment mechanism are introduced, and the error contributions of these three mechanisms are 0.03 mm, 0.01 mm and 0.005 mm, respectively. Second, a measurement network based on laser tracker metrology was established, and the RMS error of the measurement system is controlled to 0.025 mm through the optimization of the measuring stations and weighted coordinate regression. Third, an original alignment approach that divides the entire assembly into three key phases by marked point edge-constrained surface is proposed. By performing a few iterations of onsite adjustment, the reflectors were aligned in the prescribed positions, and the gap quality was controlled effectively. Finally, the on-site alignment of the large CR is introduced. The final antenna surface RMS accuracy was up to 0.054 mm, and the gaps achieved the desired design index. (paper)

  12. 30 CFR 941.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE SOUTH DAKOTA § 941.761 Areas designated unsuitable for surface coal mining by act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal...

  13. 30 CFR 937.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE OREGON § 937.761 Areas designated unsuitable for surface coal mining by Act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining and... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal...

  14. 30 CFR 905.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE CALIFORNIA § 905.761 Areas designated unsuitable for surface coal mining by act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal...

  15. 30 CFR 910.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE GEORGIA § 910.761 Areas designated unsuitable for surface coal mining by Act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal...

  16. 30 CFR 903.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE ARIZONA § 903.761 Areas designated unsuitable for surface coal mining by act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, applies to surface coal mining... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal...

  17. 30 CFR 939.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE RHODE ISLAND § 939.761 Areas designated unsuitable for surface coal mining by Act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal...

  18. 30 CFR 922.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE MICHIGAN § 922.761 Areas designated unsuitable for surface coal mining by act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal...

  19. 30 CFR 921.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE MASSACHUSETTS § 921.761 Areas designated unsuitable for surface coal mining by Act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal...

  20. 30 CFR 912.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE IDAHO § 912.761 Areas designated unsuitable for surface coal mining by act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining and... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal...

  1. 30 CFR 947.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE WASHINGTON § 947.761 Areas designated unsuitable for surface coal mining by act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal...

  2. 30 CFR 942.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE TENNESSEE § 942.761 Areas designated unsuitable for surface coal mining by act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal...

  3. 30 CFR 903.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... for surface coal mining operations. 903.762 Section 903.762 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE ARIZONA § 903.762 Criteria for designating areas as unsuitable for surface coal mining operations. Part 762 of this chapter, Criteria for Designating Areas Unsuitable for Surface Coal Mining...

  4. 30 CFR 922.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... for surface coal mining operations. 922.762 Section 922.762 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE MICHIGAN § 922.762 Criteria for designating areas as unsuitable for surface coal mining operations. Part 762 of this chapter, Criteria for Designating Areas Unsuitable for Surface Coal Mining...

  5. 30 CFR 937.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... for surface coal mining operations. 937.762 Section 937.762 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE OREGON § 937.762 Criteria for designating areas as unsuitable for surface coal mining operations. Part 762 of this chapter, Criteria for Designating Areas Unsuitable for Surface Coal Mining...

  6. 30 CFR 912.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... for surface coal mining operations. 912.762 Section 912.762 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE IDAHO § 912.762 Criteria for designating areas as unsuitable for surface coal mining operations. Part 762 of this chapter, Criteria for Designating Areas Unsuitable for Surface Coal Mining...

  7. 30 CFR 910.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... for surface coal mining operations. 910.762 Section 910.762 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE GEORGIA § 910.762 Criteria for designating areas as unsuitable for surface coal mining operations. Part 762 of this chapter, Criteria for Designating Areas Unsuitable for Surface Coal Mining...

  8. An approach for mapping large-area impervious surfaces: Synergistic use of Landsat-7 ETM+ and high spatial resolution imagery

    Science.gov (United States)

    Yang, Limin; Huang, Chengquan; Homer, Collin G.; Wylie, Bruce K.; Coan, Michael

    2003-01-01

    A wide range of urban ecosystem studies, including urban hydrology, urban climate, land use planning, and resource management, require current and accurate geospatial data of urban impervious surfaces. We developed an approach to quantify urban impervious surfaces as a continuous variable by using multisensor and multisource datasets. Subpixel percent impervious surfaces at 30-m resolution were mapped using a regression tree model. The utility, practicality, and affordability of the proposed method for large-area imperviousness mapping were tested over three spatial scales (Sioux Falls, South Dakota, Richmond, Virginia, and the Chesapeake Bay areas of the United States). Average error of predicted versus actual percent impervious surface ranged from 8.8 to 11.4%, with correlation coefficients from 0.82 to 0.91. The approach is being implemented to map impervious surfaces for the entire United States as one of the major components of the circa 2000 national land cover database.

  9. BET surface area distributions in polar stream sediments: Implications for silicate weathering in a cold-arid environment

    Science.gov (United States)

    Marra, Kristen R.; Elwood Madden, Megan E; Soreghan, Gerilyn S.; Hall, Brenda L

    2014-01-01

    BET surface area values are critical for quantifying the amount of potentially reactive sediments available for chemical weathering and ultimately, prediction of silicate weathering fluxes. BET surface area values of fine-grained (<62.5 μm) sediment from the hyporheic zone of polar glacial streams in the McMurdo Dry Valleys, Antarctica (Wright and Taylor Valleys) exhibit a wide range (2.5–70.6 m2/g) of surface area values. Samples from one (Delta Stream, Taylor Valley) of the four sampled stream transects exhibit high values (up to 70.6 m2/g), which greatly exceed surface area values from three temperate proglacial streams (0.3–12.1 m2/g). Only Clark stream in Wright Valley exhibits a robust trend with distance, wherein surface area systematically decreases (and particle size increases) in the mud fraction downstream, interpreted to reflect rapid dissolution processes in the weathering environment. The remaining transects exhibit a range in variability in surface area distributions along the length of the channel, likely related to variations in eolian input to exposed channel beds, adjacent snow drifts, and to glacier surfaces, where dust is trapped and subsequently liberated during summer melting. Additionally, variations in stream discharge rate, which mobilizes sediment in pulses and influences water:rock ratios, the origin and nature of the underlying drift material, and the contribution of organic acids may play significant roles in the production and mobilization of high-surface area sediment. This study highlights the presence of sediments with high surface area in cold-based glacier systems, which influences models of chemical denudation rates and the impact of glacial systems on the global carbon cycle.

  10. Proper construction of ab initio global potential surfaces with accurate long-range interactions

    International Nuclear Information System (INIS)

    Ho, Tak-San; Rabitz, Herschel

    2000-01-01

    An efficient procedure based on the reproducing kernel Hilbert space interpolation method is presented for constructing intermolecular potential energy surfaces (PES) using not only calculated ab initio data but also a priori information on long-range interactions. Explicitly, use of the reciprocal power reproducing kernel on the semiinfinite interval [0,∞) yields a set of exact linear relations between dispersion (multipolar) coefficients and PES data points at finite internuclear separations. Consequently, given a combined set of ab initio data and the values of dispersion (multipolar) coefficients, the potential interpolation problem subject to long-range interaction constraints can be solved to render globally smooth, asymptotically accurate ab initio potential energy surfaces. Very good results have been obtained for the one-dimensional He-He potential curve and the two-dimensional Ne-CO PES. The construction of the Ne-CO PES was facilitated by invoking a new reproducing kernel for the angular coordinate based on the optimally stable and shape-preserving Bernstein basis functions. (c) 2000 American Institute of Physics

  11. A high dynamic range structured light means for the 3D measurement of specular surface

    Science.gov (United States)

    Song, Zhan; Jiang, Hualie; Lin, Haibo; Tang, Suming

    2017-08-01

    This paper presents a novel structured light approach for the 3D reconstruction of specular surface. The binary shifting strip is adopted as structured light pattern instead of conventional sinusoidal pattern. Based on the framework of conventional High Dynamic Range (HDR) imaging technique, an efficient means is first introduced to estimate the camera response function. And then, dynamic range of the generated radiance map is compressed in the gradient domain by introducing an attenuation function. Subject to the change of lighting conditions caused by projecting different structured light patterns, the structure light image with middle exposure level is selected as the reference image and used for the slight adjustment of the primary fused image. Finally, the regenerated structured light images with well exposing condition are used for 3D reconstruction of the specular surface. To evaluate performance of the method, some stainless stamping parts with strong reflectivity are used for the experiments. And the results showed that, different specular targets with various shapes can be precisely reconstructed by the proposed method.

  12. Application of Long-Range Surface Plasmon Resonance for ABO Blood Typing

    Directory of Open Access Journals (Sweden)

    Wanida Tangkawsakul

    2016-01-01

    Full Text Available In this study, we demonstrate a long-range surface plasmon resonance (LR-SPR biosensor for the detection of whole cell by captured antigens A and B on the surface of red blood cells (RBCs as a model. The LR-SPR sensor chip consists of high-refractive index glass, a Cytop film layer, and a thin gold (Au film, which makes the evanescent field intensity and the penetration depth longer than conventional SPR. Therefore, the LR-SPR biosensor has improved capability for detecting large analytes, such as RBCs. The antibodies specific to blood group A and group B (Anti-A and Anti-B are covalently immobilized on a grafting self-assembled monolayer (SAM/Au surface on the biosensor. For blood typing, RBC samples can be detected by the LR-SPR biosensor through a change in the refractive index. We determined that the results of blood typing using the LR-SPR biosensor are consistent with the results obtained from the agglutination test. We obtained the lowest detection limits of 1.58 × 105 cells/ml for RBC-A and 3.83 × 105 cells/ml for RBC-B, indicating that the LR-SPR chip has a higher sensitivity than conventional SPR biosensors (3.3 × 108 cells/ml. The surface of the biosensor can be efficiently regenerated using 20 mM NaOH. In summary, as the LR-SPR technique is sensitive and has a simple experimental setup, it can easily be applied for ABO blood group typing.

  13. Effects of raw material texture and activation manner on surface area of porous carbons derived from biomass resources.

    Science.gov (United States)

    Zhang, Feng; Li, Guo-Dong; Chen, Jie-Sheng

    2008-11-01

    Porous carbons have been prepared from biomass resources, such as cornstalks, rice straws, pine needles and pinecone hulls, through a simple carbonization and KOH solution activation process. The pore sizes of the obtained porous carbons are mainly distributed in the range of 1-2 nm, whereas the surface areas of the materials vary from 1000 to more than 3000 m(2) g(-1) depending on the raw materials and preparation conditions. It is found that the biomass texture and the activation manner play key roles in determination of surface areas of the porous carbons. In addition, the amount of activation agent, the activation temperature and the activation time also affect the surface area of the porous carbons but to a less extent. The obtained porous carbons with high surface areas show good performance when used as Pt-catalyst supports for cinanamaldehyde hydrogenation.

  14. Surface Plasmon Polariton-Assisted Long-Range Exciton Transport in Monolayer Semiconductor Lateral Heterostructure

    Science.gov (United States)

    Shi, Jinwei; Lin, Meng-Hsien; Chen, Yi-Tong; Estakhri, Nasim Mohammadi; Tseng, Guo-Wei; Wang, Yanrong; Chen, Hung-Ying; Chen, Chun-An; Shih, Chih-Kang; Alã¹, Andrea; Li, Xiaoqin; Lee, Yi-Hsien; Gwo, Shangjr

    Recently, two-dimensional (2D) semiconductor heterostructures, i.e., atomically thin lateral heterostructures (LHSs) based on transition metal dichalcogenides (TMDs) have been demonstrated. In an optically excited LHS, exciton transport is typically limited to a rather short spatial range ( 1 micron). Furthermore, additional losses may occur at the lateral interfacial regions. Here, to overcome these challenges, we experimentally implement a planar metal-oxide-semiconductor (MOS) structure by placing a monolayer of WS2/MoS2 LHS on top of an Al2O3 capped Ag single-crystalline plate. We found that the exciton transport range can be extended to tens of microns. The process of long-range exciton transport in the MOS structure is confirmed to be mediated by an exciton-surface plasmon polariton-exciton conversion mechanism, which allows a cascaded energy transfer process. Thus, the planar MOS structure provides a platform seamlessly combining 2D light-emitting materials with plasmonic planar waveguides, offering great potential for developing integrated photonic/plasmonic functionalities.

  15. Changes in glacier area and volume in Terskey Ala-Too Range in the second half of XX century

    Directory of Open Access Journals (Sweden)

    S. S. Kutuzov

    2012-01-01

    Full Text Available Changes in the extent of glaciers and rates of glacier termini retreat in the eastern Terskey-Alatoo Range, the Tien Shan Mountains, Central Asia have been evaluated using the remote sensing techniques. Changes in the extent of 109 glaciers between 1965, 1990 and 2003 have been estimated through the delineation of glacier outlines on the topographic maps, Landsat TM and ASTER imagery for 1965, 1990 and 2003 respectively. Glacier surface area has decreased by 12.6% of the 1965 value between 1965 and 2003. Detailed mapping of 10 glaciers using historical maps and aerial photographs from the 1943–1977 period, has enabled glacier extent variations over the 20th century to be identified with a higher temporal resolution. Glacial retreat was slow in the early 20th century but increased considerably between 1943 and 1956 and then again after 1977. The post-1990 period has been marked by the most rapid glacier retreat since the end of the LIA. For the selected 13 glaciers volume reduction has been evaluated using a time step digital elevation models. DEM obtained from the 1:25 000 topographic maps of 1965 and 1977 were compared to SRTM data. The observed changes in the extent of glaciers are in line with the observed climatic warming. The regional weather stations have revealed a strong climatic warming during the ablation season since the 1950s at a rate of 0.02–0.03 oC a-¹. At the higher elevations in the study area represented by the Tien Shan meteorological station, the summer warming was accompanied by negative anomalies in annual precipitation in the 1990s enhancing glacier retreat. However, trends in precipitation in the post-1997 period cannot be evaluated due to the change in observational practices at this station. Neither station in the study area exhibits significant long-term trends in precipitation.

  16. Effect of impervious surface area and vegetation changes on mean ...

    African Journals Online (AJOL)

    adeniyi adeyemi

    sprawl and this has contributed to increase in surface temperature. Keyword: Thematic indices, surface temperature, Landsat, vegetation, ISA, Tshwane Metropolis. 1. Introduction. Globally, rapid increase in population in major cities has led to urban sprawl at an unprecedented rate which is, according to the analysis and ...

  17. Effect of Precipitation Conditions on the Specific Surface Area of Neptunium Oxide

    International Nuclear Information System (INIS)

    HILL, BENJAMINC.

    2004-01-01

    Neptunium oxalate was precipitated under nominal and bounding HB-Line flowsheet conditions. The nominal case represents expected normal HB-Line operation. The bounding case represents process flowsheet extremes that could occur which are anticipated to decrease particle size and increase surface area. The neptunium oxalate produced under bounding conditions was used to validate the effectiveness of HB-Line calcination conditions. The maximum specific surface area of the neptunium oxide (NpO2) used in gas generation testing was 5.34 m2/g. Experiments were conducted to verify that even under bounding precipitation conditions the SSA of NpO2 produced would remain within the range evaluated during gas generation testing. The neptunium oxalate from nominal and bounding precipitation conditions was calcined at 600 degrees Celsius and 625 degrees Celsius, respectively, to form NpO2. Samples from each batch of neptunium oxalate were calcined for one, two, or four hours. Results indicate that the SSA of NpO2 continues to decrease between one and four hours. After two hours of calcination at 625 degrees Celsius, the SSA of NpO2 from the bounding case meets the surface area requirements for limiting moisture uptake

  18. Propagation of long-range surface plasmon polaritons in photonic band gap structures

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra; Søndergaard, Thomas; Nikolajsen, Thomas

    2005-01-01

    We study the interaction of long-range surface plasmon polaritons (LR-SPPs), excited at telecommunication wavelengths, with photonic crystals (PCs) formed by periodic arrays of gold bumps that are arranged in a triangular lattice and placed symmetrically on both sides of a thin gold fil embedded...... in polymer. Radiation is delivered to and from the PC structures with the help of LR-SPP guides that consist of 8 mm wide and 15 nm thick gold stripes attached to wide film sections (of the same thickness) covered with bumps (diameter ~300 nm, height up to 150 nm on each side of the film). We investigate......, is rather weak, so that the photonic bandgap effect might be expected to take place only for some particular propagation directions. Preliminary experiments on LR-SPP bending and splitting at large angles are reported, and further research directions are discussed....

  19. Integrated-Optics Components Utilizing Long-Range Surface Plasmon Polaritons

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra

    2004-01-01

    This thesis describes a new class of components for integrated optics, based on the propagation of long-range surface plasmon polaritons (LR-SPPs) along metal stripes embedded in a dielectric. These novel components can provide guiding of light as well as coupling and splitting from/into a number...... fabricated and optically characterized. At 1570 nm, coupling lengths of 1.9 and 0.8 mm are found for directional couplers with waveguides separated 4 and 0 µm, respectively. LR-SPP-based waveguides and waveguide components are modeled using the effective-refractive-index method and a good agreement...... with experimental results is obtained. The interaction of LR-SPPs with photonic crystals (PCs) is also studied. The PC structures are formed by periodic arrays of gold bumps that are arranged in a triangular lattice and placed symmetrically on both sides of a thin gold film. The LR-SPP transmission through...

  20. Classification Demonstration at the Former Spencer Artillery Range, TN Open Area

    Science.gov (United States)

    2014-01-01

    estcp.org/content/download/9593/122667/file/MR-200603-FR.pdf. 5. Remedial Investigation, Former Spencer Artillery Range, Spencer/ Van Buren County...Demonstration of Advanced Geophysics and Classification Technologies on Munitions Response Sites, Former Spencer Artillery Range, Van Buren County, Tennessee

  1. Changes in the Surface Area of Glaciers in Northern Eurasia

    Science.gov (United States)

    Khromova, T.; Nosenko, G.

    2012-12-01

    Glaciers are widely recognized as key indicators of climate change. Recent evidence suggests an acceleration of glacier mass loss in several key mountain regions. Glacier recession implies the landscape changes in the glacial zone, origin of new lakes and activation of natural disaster processes, catastrophic mudflows, ice avalanches, outburst floods, and etc. The presence of glaciers in itself threats to human life, economic activity and growing infrastructure. Economical and recreational human activity in mountain regions requires relevant information on snow and ice objects. Absence or inadequacy of such information results in financial and human losses. A more comprehensive evaluation of glacier changes is imperative to assess ice contributions to global sea level rise and the future of water resources from glacial basins. One of the urgent steps is a full inventory of all ice bodies, their volume and changes The first estimation of glaciers state and glaciers distribution in the big part of Northern Eurasia has been done in the USSR Glacier Inventory published in 1966 -1980 as a part of IHD activity. The Inventory is based on topographic maps and air photos and reflects the status of the glaciers in 1957-1970y. There is information about 23796 glaciers with area of 78222.3 km2 in the Inventory. It covers 23 glacier systems on Northern Eurasia. In the 80th the USSR Glacier Inventory has been transformed in the digital form as a part of the World Glacier Inventory. Recent satellite data provide a unique opportunity to look again at these glaciers and to evaluate changes in glacier extent for the second part of XX century. In the paper we report about 15 000 glaciers outlines for Caucasus, Pamir, Tien-Shan, Altai, Syntar-Khayata, Cherskogo Range, Kamchatka and Russian Arctic which have been derived from ASTER and Landsat imagery and could be used for glacier changes evaluation. The results show that glaciers are retreating in all these regions. There is, however

  2. SMAPVEX12 Surface Roughness Data for Agricultural Area V001

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains surface roughness data collected at several agricultural sites as a part of the Soil Moisture Active Passive Validation Experiment 2012...

  3. Characteristics of surface O{sub 3} over Qinghai Lake area in Northeast Tibetan Plateau, China

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Zhenxing, E-mail: zxshen@mail.xjtu.edu.cn [Department of Environmental Sciences and Engineering, Xi' an Jiaotong University, Xi' an (China); Key Lab of Aerosol, SKLLQG, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Cao, Junji [Key Lab of Aerosol, SKLLQG, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Zhang, Leiming [Air Quality Research Division, Environment Canada, Toronto (Canada); Zhao, Zhuzi [Key Lab of Aerosol, SKLLQG, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Dong, Jungang [School of Architecture, Xi' an University of Architecture and Technology, Xi' an 710055 (China); Wang, Linqing [Department of Environmental Sciences and Engineering, Xi' an Jiaotong University, Xi' an (China); Wang, Qiyuan; Li, Guohui; Liu, Suixin [Key Lab of Aerosol, SKLLQG, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Zhang, Qian [Department of Environmental Sciences and Engineering, Xi' an Jiaotong University, Xi' an (China)

    2014-12-01

    Surface O{sub 3} was monitored continuously during Aug. 12, 2010 to Jul. 21, 2011 at a high elevation site (3200 m above sea level) in Qinghai Lake area (36°58′37″N, 99°53′56″E) in Northeast Tibetan Plateau, China. Daily average O{sub 3} ranged from 21.8 ppbv to 65.3 ppbv with an annual average of 41.0 ppbv. Seasonal average of O{sub 3} followed a decreasing order of summer > autumn > spring > winter. Diurnal variations of O{sub 3} showed low concentrations during daytime and high concentrations during late night and early morning. An intensive campaign was also conducted during Aug. 13–31, 2010 to investigate correlations between meteorological or chemical conditions and O{sub 3}. It was found that O{sub 3} was poorly correlated with solar radiation due to the insufficient NO{sub x} in the ambient air, thus limiting O{sub 3} formation under strong solar radiation. In contrast, high O{sub 3} levels always coincided with strong winds, suggesting that stratospheric O{sub 3} and long range transport might be the main sources of O{sub 3} in this rural area. Back-trajectory analysis supported this hypothesis and further indicated the transport of air masses from northwest, northeast and southeast directions. - Highlights: • Surface O{sub 3} was measured in Qinghai Lake area in Northeast Tibetan Plateau, China. • The O{sub 3} chemical formation was under a strong NOx-limited in Qinghai Lake areas. • Stratospheric O{sub 3} and transport might be the main sources of O{sub 3} in this area.

  4. Characteristics of surface O3 over Qinghai Lake area in Northeast Tibetan Plateau, China

    International Nuclear Information System (INIS)

    Shen, Zhenxing; Cao, Junji; Zhang, Leiming; Zhao, Zhuzi; Dong, Jungang; Wang, Linqing; Wang, Qiyuan; Li, Guohui; Liu, Suixin; Zhang, Qian

    2014-01-01

    Surface O 3 was monitored continuously during Aug. 12, 2010 to Jul. 21, 2011 at a high elevation site (3200 m above sea level) in Qinghai Lake area (36°58′37″N, 99°53′56″E) in Northeast Tibetan Plateau, China. Daily average O 3 ranged from 21.8 ppbv to 65.3 ppbv with an annual average of 41.0 ppbv. Seasonal average of O 3 followed a decreasing order of summer > autumn > spring > winter. Diurnal variations of O 3 showed low concentrations during daytime and high concentrations during late night and early morning. An intensive campaign was also conducted during Aug. 13–31, 2010 to investigate correlations between meteorological or chemical conditions and O 3 . It was found that O 3 was poorly correlated with solar radiation due to the insufficient NO x in the ambient air, thus limiting O 3 formation under strong solar radiation. In contrast, high O 3 levels always coincided with strong winds, suggesting that stratospheric O 3 and long range transport might be the main sources of O 3 in this rural area. Back-trajectory analysis supported this hypothesis and further indicated the transport of air masses from northwest, northeast and southeast directions. - Highlights: • Surface O 3 was measured in Qinghai Lake area in Northeast Tibetan Plateau, China. • The O 3 chemical formation was under a strong NOx-limited in Qinghai Lake areas. • Stratospheric O 3 and transport might be the main sources of O 3 in this area

  5. Surface Sediment Analysis on Petroleum Hydrocarbon and Total Organic Carbon from Coastal Area of Papar to Tuaran, Sabah

    International Nuclear Information System (INIS)

    Siti Aishah Mohd Ali; Payus, C.; Masni Mohd Ali

    2015-01-01

    Total petroleum hydrocarbons (TPH) and total organic carbon (TOC) were investigated in surface sediments along coastal area of Papar to Tuaran, Sabah. Surface sediment samples were collected in 24 different stations in each area by using Ponar grab sampler. Samples were extracted for TPH using standard method sediment/ sludge APHA 5520E and analyzed using UV/VIS spectrophotometer while for TOC method analysis using United Nations Environment Programme (UNEP)/ MAP Athens (2006). The range of TPH concentrations in surface sediments were recorded at 0.24 - 20.65 mg/ kg dw Miri crude oil equivalents, meanwhile the TOC percentage ranged from 0.03 - 4.02 %. In the mean time, the statistical analysis by Pearson correlation showed a positive correlation with coefficient, r = 0.790 which showing the TPH concentrations significantly have influence on the TOC accumulations in the surface sediment. (author)

  6. Surface water areas significantly impacted 2014 dengue outbreaks in Guangzhou, China

    International Nuclear Information System (INIS)

    Tian, Huaiyu; Huang, Shanqian; Zhou, Sen; Bi, Peng; Yang, Zhicong; Li, Xiujun; Chen, Lifan; Cazelles, Bernard; Yang, Jing; Luo, Lei; Jing, Qinlong; Yuan, Wenping; Pei, Yao; Sun, Zhe; Yue, Tianxiang; Kwan, Mei-Po

    2016-01-01

    Dengue transmission in urban areas is strongly influenced by a range of biological and environmental factors, yet the key drivers still need further exploration. To better understand mechanisms of environment–mosquito–urban dengue transmission, we propose an empirical model parameterized and cross-validated from a unique dataset including viral gene sequences, vector dynamics and human dengue cases in Guangzhou, China, together with a 36-year urban environmental change maps investigated by spatiotemporal satellite image fusion. The dengue epidemics in Guangzhou are highly episodic and were not associated with annual rainfall over time. Our results indicate that urban environmental changes, especially variations in surface area covered by water in urban areas, can substantially alter the virus population and dengue transmission. The recent severe dengue outbreaks in Guangzhou may be due to the surge in an artificial lake construction, which could increase infection force between vector (mainly Aedes albopictus) and host when urban water area significantly increased. Impacts of urban environmental change on dengue dynamics may not have been thoroughly investigated in the past studies and more work needs to be done to better understand the consequences of urbanization processes in our changing world. - Highlights: • Urban dengue outbreak is associated with water area in Guangzhou, 1978–2014. • Surface water area can alter population size of dengue virus in urban area. • Urban dengue outbreak is not associated with annual rainfall in Guangzhou. • Spatiotemporal satellite image fusion can investigate urban environmental change. • Urban environmental change could induce virus, vector, and dengue epidemic change.

  7. High-surface-area silica nanospheres (KCC-1) with a fibrous morphology

    KAUST Repository

    Polshettiwar, Vivek

    2010-08-02

    Fibrous nanosilica: A new family of high-surface-area silica nanospheres (KCC-1) have been prepared (see picture). KCC-1 features excellent physical properties, including high surface area, unprecedented fibrous surface morphology, high thermal (up to 950 °C) and hydrothermal stabilities, and high mechanical stability. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Lung deposited surface area concentrations in a street canyon

    Science.gov (United States)

    Kuuluvainen, Heino; Hietikko, Riina; Järvinen, Anssi; Saukko, Erkka; Irjala, Matti; Niemi, Jarkko V.; Timonen, Hilkka; Keskinen, Jorma; Rönkkö, Topi

    2017-04-01

    Street canyons are interesting environments with respect to the dispersion of traffic emissions and human exposure. Pedestrians may be exposed to relatively high concentrations of fine particles and the vertical dispersion affects the human exposure above the ground level in buildings. Previously, particle concentrations have been measured in street canyons at a few different heights (Marini et al., 2015). The information on the lung deposited surface area (LDSA) concentration, which is a relevant metric for the negative health effects, is very limited even at the ground level of street canyons (Kuuluvainen et al., 2016). More information especially on the vertical dispersion and the ground level concentrations is needed, for instance, for the use of urban planning and the design of ventilation systems in buildings. Measurements were carried out in a busy street canyon in Helsinki, Finland, at an urban super-site measurement station (Mäkelänkatu 50). The data included vertical concentration profiles measured in an intensive measurement campaign with a Partector (Naneos GmbH) installed into a drone, long-term measurements with an AQ Urban particle sensor (Pegasor Ltd.), and an extensive comparison measurement in the field with different devices measuring the LDSA. These devices were an AQ Urban, Partector, DiSCmini (Testo AG), NSAM (TSI Inc.), and an ELPI+ (Dekati Ltd.). In addition, continuous measurements of gas phase components, particle size distributions, and meteorology were run at the supersite. The vertical profile measurements were con-ducted in November 2016 during two days. In the measurements, the drone was flown from the ground level to an altitude of 50 or 100 m, which is clearly above the roof level of the buildings. Altogether, 48 up-and-down flights were conducted during the two days. The vertical profiles were supported by continuous measurements at the ground level on both sides of the street canyon. The long-term measurements were conducted

  9. Fine-scale movements of rural free-ranging dogs in conservation areas in the temperate rainforest of the coastal range of southern Chile

    Science.gov (United States)

    Sepulveda, Maximiliano; Pelican, Katherine; Cross, Paul C.; Eguren, Antonieta; Singer, Randall S.

    2015-01-01

    Domestic dogs can play a variety of important roles for farmers. However, when in proximity to conservation areas, the presence of rural free-ranging dogs can be problematic due to the potential for predation of, competition with, or transmission of infectious disease to local threatened fauna. We used a frequent location radio tracking technology to study rural free-ranging dog movements and habitat use into sensitive conservation habitats. To achieve a better understanding of foray behaviors in dogs we monitored dogs (n = 14) in rural households located in an isolated area between the Valdivian Coastal Reserve and the Alerce Costero National Park in southern Chile. Dogs were mostly located near households (Dogs spent, on average, 5.3% of their time in forays with average per dog foray distances from the house ranging 0.5–1.9 km (maximum distance detected 4.3 km). Foraying behavior was positively associated with pasture habitat compared to forest habitat including protected lands. Foraying dogs rarely used forest habitat and, when entered, trails and/or roads were selected for movement. Our study provides important information about how dogs interact in a fine-scale with wildlife habitat, and, in particular, protected lands, providing insight into how dog behavior might drive wildlife interactions, and, in turn, how an understanding of dog behavior can be used to manage these interactions.

  10. Military Surface Grid Areas: Atlantic / Gulf of Mexico

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — A regular pattern of polygons that represent arbitrary delineations of an Operating Area (OPAREA). The MarineCadastre.gov team worked with the Navy to provide this...

  11. Evolution of surface area-to-volume ratio for a water meniscus evaporating between contacting silica spheres.

    Science.gov (United States)

    Cutts, R E; Burns, S E

    2010-03-01

    An experimental investigation was performed under isothermal conditions to quantify the rate of evaporation of water from a receding pendular meniscus connecting two silica spheres. Optically based measurements were used to determine the relevant meniscus dimensions, and the meniscus was modeled using a toroidal approximation. The rate of change of meniscus surface area and volume was then predicted using mathematical modeling software. The results demonstrated that once the meniscus transitioned from a relatively flat surface to one with an increasing radius of curvature, the rate of change of the ratio of surface area-to-volume was relatively constant over the range of water contents that were observable using the optical investigation techniques implemented in this study. Comparison of the flux of water from the meniscus surface demonstrated that the evaporation of bound water was four orders of magnitude slower than evaporation from a free water surface. 2009 Elsevier Inc. All rights reserved.

  12. 30 CFR 910.764 - Process for designating areas unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... surface coal mining operations. 910.764 Section 910.764 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE GEORGIA § 910.764 Process for designating areas unsuitable for surface coal mining...

  13. 30 CFR 937.764 - Process for designating areas unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... surface coal mining operations. 937.764 Section 937.764 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE OREGON § 937.764 Process for designating areas unsuitable for surface coal mining...

  14. 30 CFR 947.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... for surface coal mining operations. 947.762 Section 947.762 Mineral Resources OFFICE OF SURFACE MINING... mining operations. Part 762 of this chapter, Criteria for Designating Areas Unsuitable for Surface Coal Mining Operations, shall apply to surface coal mining and reclamation operations. ...

  15. 30 CFR 921.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... for surface coal mining operations. 921.762 Section 921.762 Mineral Resources OFFICE OF SURFACE MINING... mining operations. Part 762 of this chapter, Criteria for Designating Areas Unsuitable for Surface Coal Mining Operations, shall apply to surface coal mine operations. ...

  16. 30 CFR 922.764 - Process for designating areas unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... surface coal mining operations. 922.764 Section 922.764 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE MICHIGAN § 922.764 Process for designating areas unsuitable for surface coal mining...

  17. 30 CFR 942.764 - Process for designating areas unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... surface coal mining operations. 942.764 Section 942.764 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE TENNESSEE § 942.764 Process for designating areas unsuitable for surface coal mining... Mining Operations, shall apply to surface coal mining and reclamation operations. (b) The Secretary shall...

  18. 30 CFR 941.764 - Process for designating areas unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... surface coal mining operations. 941.764 Section 941.764 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE SOUTH DAKOTA § 941.764 Process for designating areas unsuitable for surface coal mining...

  19. 30 CFR 941.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... for surface coal mining operations. 941.762 Section 941.762 Mineral Resources OFFICE OF SURFACE MINING... mining operations. Part 762 of this chapter, Criteria for Designating Areas Unsuitable for Surface Coal Mining Operations, shall apply to surface coal mine operations. ...

  20. 30 CFR 939.764 - Process for designating areas unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... surface coal mining operations. 939.764 Section 939.764 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE RHODE ISLAND § 939.764 Process for designating areas unsuitable for surface coal mining...

  1. 30 CFR 933.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... for surface coal mining operations. 933.762 Section 933.762 Mineral Resources OFFICE OF SURFACE MINING... mining operations. Part 762 of this chapter, Criteria for Designation Areas Unsuitable for Surface Coal Mining Operations, shall apply to surface coal mining and reclamation operations. ...

  2. 30 CFR 939.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... for surface coal mining operations. 939.762 Section 939.762 Mineral Resources OFFICE OF SURFACE MINING... mining operations. Part 762 of this chapter, Criteria for Designating Areas Unsuitable for Surface Coal Mining Operations, shall apply to surface coal mining and reclamation operations. ...

  3. 30 CFR 905.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... for surface coal mining operations. 905.762 Section 905.762 Mineral Resources OFFICE OF SURFACE MINING... mining operations. Part 762 of this chapter, Criteria for Designating Areas Unsuitable for Surface Coal Mining Operations, shall apply to surface coal mining operations. ...

  4. Surface albedo measurements in Mexico City metropolitan area

    Energy Technology Data Exchange (ETDEWEB)

    Castro, T; Mar, B; Longoria, R; Ruiz Suarez, L. G [Centro de Ciencias de la Atmosfera, UNAM, Mexico, D.F. (Mexico); Morales, L [Instituto de Geografia, UNAM, Mexico, D.F. (Mexico)

    2001-04-01

    Optical and thermal properties of soils are important input data for the meteorological and photochemical modules of air quality models. As development of these models increase on spatial resolution good albedo data become more important. In this paper measurements of surface albedo of UV (295-385 nm) and visible (450-550 nm) radiation are reported for different urban and rural surfaces in the vicinity of Mexico City. It was found for the downtown zone and average albedo value of 0.05 which is in very good agreement with reported values for urban surfaces. Our albedo values measured in UV region for grey cement and green grass are of 0.10 and 0.009, respectively, and quite similar to those found at the literature of 0.11 and 0.008 for those type of surfaces. [Spanish] Las propiedades opticas y termicas de suelos son datos importantes para los modulos meteorologicos y fotoquimicos de los modelos de calidad del aire. Conforme aumenta la resolucion espacial del modelo se vuelve mas importante contar con buenos datos de albedo. En este articulo se presentan mediciones de albedo superficial de radiacion Ultravioleta (295-385 nm) y visible (450-550 nm) para diferentes superficies urbanas. Los valores medidos de albedo en la region UV para cemento gris y pasto verde son de 0.10 y 0.009, respectivamente, y son muy similares a los reportados en la literatura, 0.11 y 0.008 para este tipo de superficies.

  5. Large Area Diamond Tribological Surfaces with Negligible Wear in Extreme Environments, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — In Phase I we propose to demonstrate the processing of very large area diamond sliding bearings and tribological surfaces. The bearings and surfaces will experience...

  6. A Cultural Resource Survey of the Offense Area of the Live Fire Maneuver Range, Fort Irwin, California.

    Science.gov (United States)

    1981-02-19

    ADA2 78 ACULTURAL RESOURCE SURVEY OF THE OFFENSE AREA 0F THE 3/ LIE FRE MANEUVER ANGE FORT IRWIN CA IFRNIA U RECON SAN DIEGO CA C S BULL 19 FEB 81 R...DESCRIPTION AND RESULTS 1 I B. RECOMMENDATIONS 2 * II. CULTURAL RESOURCE REVIEW 3 A. PROJECT AREA DESCRIPTION 3 1. Location 31 2. Geology 3 3. Biology 8 I...CULTURAL RESOURCE REVIEW I A. PROJECT AREA DESCRIPTION 1. Location. The offense area of the live fire maneu-I ver range is located at Fort Irwin, San

  7. Bearing splitting and near-surface source ranging in the direct zone of deep water

    Science.gov (United States)

    Wu, Jun-Nan; Zhou, Shi-Hong; Peng, Zhao-Hui; Zhang, Yan; Zhang, Ren-He

    2016-12-01

    Sound multipath propagation is very important for target localization and identification in different acoustical zones of deep water. In order to distinguish the multipath characteristics in deep water, the Northwest Pacific Acoustic Experiment was conducted in 2015. A low-frequency horizontal line array towed at the depth of around 150 m on a receiving ship was used to receive the noise radiated by the source ship. During this experiment, a bearing-splitting phenomenon in the direct zone was observed through conventional beamforming of the horizontal line array within the frequency band 160 Hz-360 Hz. In this paper, this phenomenon is explained based on ray theory. In principle, the received signal in the direct zone of deep water arrives from two general paths including a direct one and bottom bounced one, which vary considerably in arrival angles. The split bearings correspond to the contributions of these two paths. The bearing-splitting phenomenon is demonstrated by numerical simulations of the bearing-time records and experimental results, and they are well consistent with each other. Then a near-surface source ranging approach based on the arrival angles of direct path and bottom bounced path in the direct zone is presented as an application of bearing splitting and is verified by experimental results. Finally, the applicability of the proposed ranging approach for an underwater source within several hundred meters in depth in the direct zone is also analyzed and demonstrated by simulations. Project supported by the Program of One Hundred Talented People of the Chinese Academy of Sciences and the National Natural Science Foundation of China (Grant Nos. 11434012 and 41561144006).

  8. Extended-range forecasting of Chinese summer surface air temperature and heat waves

    Science.gov (United States)

    Zhu, Zhiwei; Li, Tim

    2018-03-01

    Because of growing demand from agricultural planning, power management and activity scheduling, extended-range (5-30-day lead) forecasting of summer surface air temperature (SAT) and heat waves over China is carried out in the present study via spatial-temporal projection models (STPMs). Based on the training data during 1960-1999, the predictability sources are found to propagate from Europe, Northeast Asia, and the tropical Pacific, to influence the intraseasonal 10-80 day SAT over China. STPMs are therefore constructed using the projection domains, which are determined by these previous predictability sources. For the independent forecast period (2000-2013), the STPMs can reproduce EOF-filtered 30-80 day SAT at all lead times of 5-30 days over most part of China, and observed 30-80 and 10-80 day SAT at 25-30 days over eastern China. Significant pattern correlation coefficients account for more than 50% of total forecasts at all 5-30-day lead times against EOF-filtered and observed 30-80 day SAT, and at a 20-day lead time against observed 10-80 day SAT. The STPMs perform poorly in reproducing 10-30 day SAT. Forecasting for the first two modes of 10-30 day SAT only shows useful skill within a 15-day lead time. Forecasting for the third mode of 10-30 day SAT is useless after a 10-day lead time. The forecasted heat waves over China are determined by the reconstructed SAT which is the summation of the forecasted 10-80 day SAT and the lower frequency (longer than 80-day) climatological SAT. Over a large part of China, the STPMs can forecast more than 30% of heat waves within a 15-day lead time. In general, the STPMs demonstrate the promising skill for extended-range forecasting of Chinese summer SAT and heat waves.

  9. Changes in infraspinatus cross-sectional area and shoulder range of motion with repetitive eccentric external rotator contraction.

    Science.gov (United States)

    Oyama, Sakiko; Myers, Joseph B; Blackburn, J Troy; Colman, Eli C

    2011-02-01

    Repetitive eccentric loading results in muscle damage and subsequent changes in muscle stiffness and edema accumulation, which manifest as reduced joint range of motion and increased muscle cross-sectional area. The purpose of the study was to evaluate changes in shoulder range of motion and the infraspinatus cross-sectional area with repetitive eccentric contraction. Twenty physically active participants performed 9 sets of 25 repetitions of eccentric external rotator contractions. The ultrasonographic measurement of the infraspinatus cross-sectional area, and shoulder internal/external rotation and horizontal adduction range of motion were measured before, immediately after, and 24h after the intervention. Infraspinatus cross-sectional area significantly increased from baseline immediately after exercise (P0.05), but were significantly decreased at the 24-hour follow up from the baseline (internal rotation: Peccentric contractions may have implications for injury development in pitchers, because 1) the infraspinatus endures repetitive eccentric loading with pitching and 2) decreased internal rotation and horizontal adduction range of motion have been linked to upper extremity injuries. However, since the muscle response after eccentric loading varies by the task and previous exposure to similar stress, future study needs to investigate the time course of recovery of the muscle cross-sectional area and range of motion after pitching in competitive pitchers. Copyright © 2010 Elsevier Ltd. All rights reserved.

  10. 75 FR 65229 - Amendment and Establishment of Restricted Areas and Other Special Use Airspace, Razorback Range...

    Science.gov (United States)

    2010-10-22

    ... geographic coordinates along Arkansas State Highway 22 that were used in defining the boundary for restricted... Aeronautical Charting Office) and Memphis air route traffic control center determined that a minor refinement was needed for the geographic coordinates used to define where the restricted area boundaries...

  11. Possibilities of surface waters monitoring at mining areas using UAV

    Science.gov (United States)

    Lisiecka, Ewa; Motyka, Barbara; Motyka, Zbigniew; Pierzchała, Łukasz; Szade, Adam

    2018-04-01

    The selected, remote measurement methods are discussed, useful for determining surface water properties using mobile unmanned aerial platforms (UAV). The possibilities of using this type of solutions in the scope of measuring spatial, physicochemical and biological parameters of both natural and anthropogenic water reservoirs, including flood polders, water-filled pits, settling tanks and mining sinks were analyzed. Methods of remote identification of the process of overgrowing this type of ecosystems with water and coastal plant formations have also been proposed.

  12. The Effect of 200 MPa Pressure on Specific Surface Area of Clay

    Directory of Open Access Journals (Sweden)

    Koszela-Marek Ewa

    2015-02-01

    Full Text Available The paper presents the results of laboratory studies of the 200 MPa pressure effect on specific surface area of clay. The original high-pressure investigation stand was used for the pressure tests. Determination of the specific surface area was performed by the methylene blue adsorption method. The results of the specific surface area test were compared for non-pressurized clays and for clays pressured in a high-pressure chamber. It was found that the specific surface area of pressurized soil clearly increased. This shows that some microstructural changes take place in the soil skeleton of clays.

  13. Estimating the surface area of birds: using the homing pigeon (Columba livia) as a model.

    Science.gov (United States)

    Perez, Cristina R; Moye, John K; Pritsos, Chris A

    2014-05-08

    Estimation of the surface area of the avian body is valuable for thermoregulation and metabolism studies as well as for assessing exposure to oil and other surface-active organic pollutants from a spill. The use of frozen carcasses for surface area estimations prevents the ability to modify the posture of the bird. The surface area of six live homing pigeons in the fully extended flight position was estimated using a noninvasive method. An equation was derived to estimate the total surface area of a pigeon based on its body weight. A pigeon's surface area in the fully extended flight position is approximately 4 times larger than the surface area of a pigeon in the perching position. The surface area of a bird is dependent on its physical position, and, therefore, the fully extended flight position exhibits the maximum area of a bird and should be considered the true surface area of a bird. © 2014. Published by The Company of Biologists Ltd | Biology Open.

  14. Gender differences in knee joint cartilage thickness, volume and articular surface areas: assessment with quantitative three-dimensional MR imaging

    International Nuclear Information System (INIS)

    Faber, S.C.; Reiser, M.; Englmeier, K.H.

    2001-01-01

    Objective: To compare the cartilage thickness, volume, and articular surface areas of the knee joint between young healthy, non-athletic female and male individuals. Subjects and design. MR imaging was performed in 18 healthy subjects without local or systemic joints disease (9 female, age 22.3±2.4 years, and 9 male, age 22.2.±1.9 years), using a fat-suppressed FLASH 3D pulse sequence (TR=41 ms, TE=11 ms, FA=30 ) with sagittal orientation and a spatial resolution of 2x0.31x0.31 mm 3 . After three-dimensional reconstruction and triangulation of the knee joint cartilage plates, the cartilage thickness (mean and maximal), volume, and size of the articular surface area were quantified, independent of the original section orientation. Results and conclusions: Women displayed smaller cartilage volumes than men, the percentage difference ranging from 19.9% in the patella, to 46.6% in the medial tibia. The gender differences of the cartilage thickness were smaller, ranging from 2.0% in the femoral trochlea to 13.3% in the medial tibia for the mean thickness, and from 4.3% in the medial femoral condyle to 18.3% in the medial tibia for the maximal cartilage thickness. The differences between the cartilage surface areas were similar to those of the volumes, with values ranging from 21.0% in the femur to 33.4% in the lateral tibia. Gender differences could be reduced for cartilage volume and surface area when normalized to body weight and body weight x body height. The study demonstrates significant gender differences in cartilage volume and surface area of men and women, which need to be taken into account when retrospectively estimating articular cartilage loss in patients with symptoms of degenerative joint disease. Differences in cartilage volume are primarily due to differences in joint surface areas (epiphyseal bone size), not to differences in cartilage thickness. (orig.)

  15. X-Band high range resolution radar measurements of sea surface forward scatter at low grazing angles

    CSIR Research Space (South Africa)

    Smit, JC

    2008-05-01

    Full Text Available Radar measurements of a radar calibration sphere test target suspended in sea surface multipath propagation conditions are reported. Wideband measurements together with high range resolution (HRR) processing were employed to resolve the direct...

  16. Assessment of large aperture scintillometry for large-area surface ...

    Indian Academy of Sciences (India)

    29

    This study defines that large aperture scintillometer is robust instrument which can evaluate energy flux over a large area with a long term series time domain. Moreover, further studied should be conducted to use in crop simulation modelling, developing of new model with calibration and validation of remote sensing energy ...

  17. Development of wide area tracking method for augmented reality using multi-range fiducials

    International Nuclear Information System (INIS)

    Ishii, Hirotake; Fujino, Hidenori; Yan, Weida; Yang, Shoufeng; Shimoda, Hiroshi; Izumi, Masanori

    2009-01-01

    A new fiducial marker for augmented reality was designed along with a method that recognizes the markers captured by a camera and calculates the relative position and orientation between the markers and the camera. These markers can be used at both long and short distances without increasing the number of markers pasted in the environment. Results of the experimental evaluation show that the new marker can be used in a larger area than circular markers and more stably than square markers. (author)

  18. Phytosociological attributes of plant biodiversity of the Fort Ranikot and adjoining area (Kirthar range)

    International Nuclear Information System (INIS)

    Ishtiaq, M.; Perveen, A.

    2015-01-01

    The plant biodiversity, floristic composition and phytosociological attributes of the vascular plants of Fort Ranikot were analyzed. A total of 107 taxa were collected belonging to 41 families and 78 genera. The largest family was Poaceae containing 9 taxa, while the other major families were Papilionaceae with 6 species; Asclepiadaceae, Mimosaceae, and Solanaceae comprising of 5 species each respectively. Majority of the taxa are common throughout the study area, however, 6 species Viz. Aristolochia bracteolata, Physorrhynchus brahuicus, Plantago ciliata, Polygala erioptera, Salvadora persica and Viola stocksii were found to be very rare. The flora is dominated by Chamaephyte, followed by Therophytes, Phanerophytes, Hemicryptophytes and climbers. The aim of the present study is to provide comprehensive inventory of the study area along with its phytosociology and ecological parameters. Collectively on the basis of important value index six plants communities were recognized from different sites of the study area. The study area was categorized into six ecological sites on the basis of microclimatic conditions and topography. For comparison in these sites similarity index, beta diversity, diversity index, species evenness and maturity index was also calculated. The soil texture classes varied from loam to sandy loam and slit loam with pH of 7.78-8.24, electrical conductivity varied from 687-827 EC micro S/cm, Total dissolved salts varied from 0.36-0.71 mg-1, CaCO/sub 3/ varied from 3.48-4.21% and organic matter varied from 0.39-1.24%. Present study predict that there are certain edaphic factors, altitudinal variation, soil texture and amount of organic matter which are responsible for variation in vegetation. (author)

  19. Mesoporous high surface area Ce0.9Gd0.1O1.95 synthesized by spray drying

    DEFF Research Database (Denmark)

    Lundberg, Mats; Wang, Hsiang-Jen; Blennow Tullmar, Peter

    2011-01-01

    Mesoporous gadolinium doped cerium dioxide with high surface area was produced by spray drying using Pluronic 123 as surfactant. The powder, when calcined at 400 °C, had a BET surface area of 136 m2 g−1 and was polycrystalline as confirmed by XRD and TEM. XEDS confirmed Ce, Gd and O, as the only......, corresponding to the crystallite size calculated from XRD data. The similar size range of the mesopores and the observed crystallite size indicates that the porosity is partly formed from intergranular mesoporosity. Using the spray drying method of a surfactant assisted liquid precursor solution it can...

  20. Structure Function Studies of Vaccinia Virus Host Range Protein K1 Reveal a Novel Functional Surface for Ankyrin Repeat Proteins

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yongchao; Meng, Xiangzhi; Xiang, Yan; Deng, Junpeng (Texas-HSC); (OKLU)

    2010-06-15

    Poxvirus host tropism at the cellular level is regulated by virus-encoded host range proteins acting downstream of virus entry. The functioning mechanisms of most host range proteins are unclear, but many contain multiple ankyrin (ANK) repeats, a motif that is known for ligand interaction through a concave surface. We report here the crystal structure of one of the ANK repeat-containing host range proteins, the vaccinia virus K1 protein. The structure, at a resolution of 2.3 {angstrom}, showed that K1 consists entirely of ANK repeats, including seven complete ones and two incomplete ones, one each at the N and C terminus. Interestingly, Phe82 and Ser83, which were previously shown to be critical for K1's function, are solvent exposed and located on a convex surface, opposite the consensus ANK interaction surface. The importance of this convex surface was further supported by our additional mutagenesis studies. We found that K1's host range function was negatively affected by substitution of either Asn51 or Cys47 and completely abolished by substitution of both residues. Cys47 and Asn51 are also exposed on the convex surface, spatially adjacent to Phe82 and Ser83. Altogether, our data showed that K1 residues on a continuous convex ANK repeat surface are critical for the host range function, suggesting that K1 functions through ligand interaction and does so with a novel ANK interaction surface.

  1. Tritium in Precipitation, Surface and Groundwaters in the Zagreb Area

    International Nuclear Information System (INIS)

    Horvatincic, N.; Baresic, J.; Sironic, A.; Krajcar Bronic, I.; Obelic, B.

    2011-01-01

    Radioactive isotope tritium (3H) and stable isotopes of hydrogen (2H/1H) and oxygen (18O/16O) were measured in Sava River, precipitation and groundwater at 3 monitoring wells (piezometers) and 1 production well of the Petrusevec aquifer, close to the Sava River. Samples were collected monthly during 2010. The investigation is included in the Regional IAEA Project RER/8/016 Using Environmental Isotopes for Evaluation of Streamwater/Groundwater Interactions in Selected Aquifers in the Danube Basin. Sava River is a tributary of Danube River and the aim of the investigation is to determine the influence of surface stream of Sava River to the groundwater of aquifer used for water exploitation. In this work only 3H results were presented. 3H was measured by liquid scintillation counter Quantulus 1220, using electrolytic enrichment for all samples. 3H activity in precipitation showed slight seasonal fluctuation between 4 TU and 14 TU, with higher values in summer. 3H activity of Sava River and groundwater of the Petrusevec aquifer followed 3H of precipitation till May 2010. Significant increase of 3H in Sava River was observed in June, (199 @ 20) TU, and in the next month it fell down at 6 TU. Increase of 3H was also observed in groundwater but with damped response (maximum 60 TU) and with delay of 2 - 3 months related to Sava River. Different response of different piezometers and the well indicated the different infiltration times of surface water of Sava River to groundwater of the Petrusevec aquifer. The increased 3H activity in surface and groundwaters was caused by release of tritiated water from the Krsko Nuclear Power Plant, 30 km upstream from Zagreb. The results of 3H, 2H/1H and 18O/16O measurements will be used to determine the infiltration time of groundwater of the Petrusevec aquifer using conceptual and mathematical models. (author)

  2. A compendium of results from long-range alpha detector soil surface monitoring: June 1992--May 1994

    International Nuclear Information System (INIS)

    Garner, S.E.; Bounds, J.A.; Allander, K.S.; Johnson, J.D.; MacArthur, D.W.; Caress, R.W.

    1994-11-01

    Soil surface monitors based on long-range alpha detector (LRAD) technology are being used to monitor alpha contamination at various sites in the Department of Energy complex. These monitors, the large soil-surface monitor (LSSM) and the small soil-surface monitor (SSSM), were used to help characterize sites at Fernald, Ohio, and active or inactive firing sites at Sandia National Laboratories and Los Alamos National Laboratory. Monitoring results are presented herein in chronological order

  3. Adsorption of a single polymer chain on a surface: effects of the potential range.

    Science.gov (United States)

    Klushin, Leonid I; Polotsky, Alexey A; Hsu, Hsiao-Ping; Markelov, Denis A; Binder, Kurt; Skvortsov, Alexander M

    2013-02-01

    We investigate the effects of the range of adsorption potential on the equilibrium behavior of a single polymer chain end-attached to a solid surface. The exact analytical theory for ideal lattice chains interacting with a planar surface via a box potential of depth U and width W is presented and compared to continuum model results and to Monte Carlo (MC) simulations using the pruned-enriched Rosenbluth method for self-avoiding chains on a simple cubic lattice. We show that the critical value U(c) corresponding to the adsorption transition scales as W(-1/ν), where the exponent ν=1/2 for ideal chains and ν≈3/5 for self-avoiding walks. Lattice corrections for finite W are incorporated in the analytical prediction of the ideal chain theory U(c)≈(π(2)/24)(W+1/2)(-2) and in the best-fit equation for the MC simulation data U(c)=0.585(W+1/2)(-5/3). Tail, loop, and train distributions at the critical point are evaluated by MC simulations for 1≤W≤10 and compared to analytical results for ideal chains and with scaling theory predictions. The behavior of a self-avoiding chain is remarkably close to that of an ideal chain in several aspects. We demonstrate that the bound fraction θ and the related properties of finite ideal and self-avoiding chains can be presented in a universal reduced form: θ(N,U,W)=θ(NU(c),U/U(c)). By utilizing precise estimations of the critical points we investigate the chain length dependence of the ratio of the normal and lateral components of the gyration radius. Contrary to common expectations this ratio attains a limiting universal value /=0.320±0.003 only at N~5000. Finite-N corrections for this ratio turn out to be of the opposite sign for W=1 and for W≥2. We also study the N dependence of the apparent crossover exponent φ(eff)(N). Strong corrections to scaling of order N(-0.5) are observed, and the extrapolated value φ=0.483±0.003 is found for all values of W. The strong correction to scaling effects found here explain why

  4. Test Area C-74 Complex Final Range Environmental Assessment at Eglin Air Force Base, Florida

    Science.gov (United States)

    2015-08-21

    testing category (U.S. Air Force, 2007). Kinetic Energy Munitions Facility (KEMTF) The KEMTF is a 2,000-foot, dual rail sled track inclined to 0.6...KEMTF. After the munitions impact with the reusable wall, the wall can be removed and a new concrete wall can be welded into place (U.S. Air Force...dual- rail sled track. The downrange impact/recovery area consists of about 773 acres of maintained grassland, a 4-acre pond, and 83 acres in riparian

  5. Beyond the lotus effect: roughness influences on wetting over a wide surface-energy range.

    Science.gov (United States)

    Spori, Doris M; Drobek, Tanja; Zürcher, Stefan; Ochsner, Mirjam; Sprecher, Christoph; Mühlebach, Andreas; Spencer, Nicholas D

    2008-05-20

    To enhance our understanding of liquids in contact with rough surfaces, a systematic study has been carried out in which water contact angle measurements were performed on a wide variety of rough surfaces with precisely controlled surface chemistry. Surface morphologies consisted of sandblasted glass slides as well as replicas of acid-etched, sandblasted titanium, lotus leaves, and photolithographically manufactured golf-tee shaped micropillars (GTMs). The GTMs display an extraordinarily stable, Cassie-type hydrophobicity, even in the presence of hydrophilic surface chemistry. Due to pinning effects, contact angles on hydrophilic rough surfaces are shifted to more hydrophobic values, unless roughness or surface energy are such that capillary forces become significant, leading to complete wetting. The observed hydrophobicity is thus not consistent with the well-known Wenzel equation. We have shown that the pinning strength of a surface is independent of the surface chemistry, provided that neither capillary forces nor air enclosure are involved. In addition, pinning strength can be described by the axis intercept of the cosine-cosine plot of contact angles for rough versus flat surfaces with the same surface chemistries.

  6. Birds of two protected areas in the southern range of the Brazilian Araucaria forest

    Directory of Open Access Journals (Sweden)

    Ismael Franz

    2014-01-01

    Full Text Available Over 70% of threatened birds in the state of Rio Grande do Sul, south Brazil, inhabit forest environments. The creation and maintenance of protected areas is one of the most important measures aiming to mitigate these problems. However, the knowledge of the local biodiversity is essential so that these areas can effectively preserve the natural resources. Between 2004 and 2009 we sampled the avifauna in two conservation units in Rio Grande do Sul: Floresta Nacional de Canela (FNC and Parque Natural Municipal da Ronda (PMR, both representative of the Mixed Humid Forest (Araucaria Forest. A total of 224 species was recorded, 116 at FNC and 201 at PMR, ten of which threatened regionally: Pseudastur polionotus, Odontophorus capueira, Patagioenas cayennensis, Amazona pretrei, A. vinacea, Triclaria malachitacea, Campephilus robustus, Grallaria varia, Procnias nudicollis and Sporophila melanogaster. Richness and species composition seem to be related to different stages of forest conservation, to size and connectivity, as well as to the diversity of environments. The better conservation of PMR compared to FNC, allied to its geographic position, results in a richer avifauna, with a larger amount of rare and endangered species, as well as species sensitive to disturbance and endemic to the Atlantic Rainforest. We suggest management actions aiming the conservation and the long-term recovery of natural environments at these sites.

  7. Response of the global surface ozone distribution to Northern Hemisphere sea surface temperature changes: implications for long-range transport

    Science.gov (United States)

    Yi, Kan; Liu, Junfeng; Ban-Weiss, George; Zhang, Jiachen; Tao, Wei; Cheng, Yanli; Tao, Shu

    2017-07-01

    The response of surface ozone (O3) concentrations to basin-scale warming and cooling of Northern Hemisphere oceans is investigated using the Community Earth System Model (CESM). Idealized, spatially uniform sea surface temperature (SST) anomalies of ±1 °C are individually superimposed onto the North Pacific, North Atlantic, and North Indian oceans. Our simulations suggest large seasonal and regional variability in surface O3 in response to SST anomalies, especially in the boreal summer. The responses of surface O3 associated with basin-scale SST warming and cooling have similar magnitude but are opposite in sign. Increasing the SST by 1 °C in one of the oceans generally decreases the surface O3 concentrations from 1 to 5 ppbv. With fixed emissions, SST increases in a specific ocean basin in the Northern Hemisphere tend to increase the summertime surface O3 concentrations over upwind regions, accompanied by a widespread reduction over downwind continents. We implement the integrated process rate (IPR) analysis in CESM and find that meteorological O3 transport in response to SST changes is the key process causing surface O3 perturbations in most cases. During the boreal summer, basin-scale SST warming facilitates the vertical transport of O3 to the surface over upwind regions while significantly reducing the vertical transport over downwind continents. This process, as confirmed by tagged CO-like tracers, indicates a considerable suppression of intercontinental O3 transport due to increased tropospheric stability at lower midlatitudes induced by SST changes. Conversely, the responses of chemical O3 production to regional SST warming can exert positive effects on surface O3 levels over highly polluted continents, except South Asia, where intensified cloud loading in response to North Indian SST warming depresses both the surface air temperature and solar radiation, and thus photochemical O3 production. Our findings indicate a robust linkage between basin-scale SST

  8. Response of the global surface ozone distribution to Northern Hemisphere sea surface temperature changes: implications for long-range transport

    Directory of Open Access Journals (Sweden)

    K. Yi

    2017-07-01

    Full Text Available The response of surface ozone (O3 concentrations to basin-scale warming and cooling of Northern Hemisphere oceans is investigated using the Community Earth System Model (CESM. Idealized, spatially uniform sea surface temperature (SST anomalies of ±1 °C are individually superimposed onto the North Pacific, North Atlantic, and North Indian oceans. Our simulations suggest large seasonal and regional variability in surface O3 in response to SST anomalies, especially in the boreal summer. The responses of surface O3 associated with basin-scale SST warming and cooling have similar magnitude but are opposite in sign. Increasing the SST by 1 °C in one of the oceans generally decreases the surface O3 concentrations from 1 to 5 ppbv. With fixed emissions, SST increases in a specific ocean basin in the Northern Hemisphere tend to increase the summertime surface O3 concentrations over upwind regions, accompanied by a widespread reduction over downwind continents. We implement the integrated process rate (IPR analysis in CESM and find that meteorological O3 transport in response to SST changes is the key process causing surface O3 perturbations in most cases. During the boreal summer, basin-scale SST warming facilitates the vertical transport of O3 to the surface over upwind regions while significantly reducing the vertical transport over downwind continents. This process, as confirmed by tagged CO-like tracers, indicates a considerable suppression of intercontinental O3 transport due to increased tropospheric stability at lower midlatitudes induced by SST changes. Conversely, the responses of chemical O3 production to regional SST warming can exert positive effects on surface O3 levels over highly polluted continents, except South Asia, where intensified cloud loading in response to North Indian SST warming depresses both the surface air temperature and solar radiation, and thus photochemical O3 production. Our findings indicate a robust linkage

  9. Surface water areas significantly impacted 2014 dengue outbreaks in Guangzhou, China.

    Science.gov (United States)

    Tian, Huaiyu; Huang, Shanqian; Zhou, Sen; Bi, Peng; Yang, Zhicong; Li, Xiujun; Chen, Lifan; Cazelles, Bernard; Yang, Jing; Luo, Lei; Jing, Qinlong; Yuan, Wenping; Pei, Yao; Sun, Zhe; Yue, Tianxiang; Kwan, Mei-Po; Liu, Qiyong; Wang, Ming; Tong, Shilu; Brownstein, John S; Xu, Bing

    2016-10-01

    Dengue transmission in urban areas is strongly influenced by a range of biological and environmental factors, yet the key drivers still need further exploration. To better understand mechanisms of environment-mosquito-urban dengue transmission, we propose an empirical model parameterized and cross-validated from a unique dataset including viral gene sequences, vector dynamics and human dengue cases in Guangzhou, China, together with a 36-year urban environmental change maps investigated by spatiotemporal satellite image fusion. The dengue epidemics in Guangzhou are highly episodic and were not associated with annual rainfall over time. Our results indicate that urban environmental changes, especially variations in surface area covered by water in urban areas, can substantially alter the virus population and dengue transmission. The recent severe dengue outbreaks in Guangzhou may be due to the surge in an artificial lake construction, which could increase infection force between vector (mainly Aedes albopictus) and host when urban water area significantly increased. Impacts of urban environmental change on dengue dynamics may not have been thoroughly investigated in the past studies and more work needs to be done to better understand the consequences of urbanization processes in our changing world. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

  10. Rescaled Range Analysis of Microtremors in the Yun-Chia Area, Taiwan

    Directory of Open Access Journals (Sweden)

    Young-Fo Chang

    2006-01-01

    Full Text Available Hurst’s analysis of natural background microtremors at 10 stations in Yun-Li and Chia-Yi Counties, Taiwan, yields high values of H, ranging from 0.733 to 0.934. These values are found to be site-specific and stationary. Microtremors recorded in the foothills, on a hillside and at rock sites have higher H values than those on the alluvial plain, near the coast or at soil sites although they may very well be affected by the local environment and geology. Since low-frequency microtremors tend to be more persistent in time, we suggest that the high values of the Hurst exponent H may be causally correlated with the presence of low frequencies. This seems likely because Hurst exponents H > 0.5 mean a higher statistical persistence of a random signal.

  11. Establishment of reference range for thyroid hormones in normal pregnant women in China's coastal area.

    Science.gov (United States)

    Zha, J; Ming, D; Jiang, Y; Huang, C; Jiang, T; Chen, C; Lin, R; Su, W; Gu, S

    2014-01-01

    The current study aims to establish reference ranges for thyroid hormones in normal pregnant women during their pregnancy period. A one-time cross-sectional survey was conducted on 490 normal pregnant women and 51 nonpregnant women (control). The serum thyroid stimulating hormone (TSH), free triiodothyronine (FT3), and free tetraiodothyronine (FT4) levels were measured. The serum FT3 and FT4 levels in pregnant women decreased gradually from the first to the last three months of pregnancy (p serum TSH level increased gradually during the whole pregnancy (p < 0.01), and was significantly lower than the control (p < 0.01) in the first three months. However, in the middle and last three months of pregnancy, TSH was higher than the control (p < 0.01). The thyroid hormone levels in normal pregnant women are different from those in non-pregnant women; significant differences exist among the three stages of pregnancy.

  12. Use of Atlantic Forest protected areas by free-ranging dogs: estimating abundance and persistence of use

    Science.gov (United States)

    Paschoal, Ana Maria; Massara, Rodrigo; Bailey, Larissa L.; Kendall, William L.; Doherty, Paul F.; Hirsch, Andre; Chiarello, Adriano; Paglia, Adriano

    2016-01-01

    Worldwide, domestic dogs (Canis familiaris) are one of the most common carnivoran species in natural areas and their populations are still increasing. Dogs have been shown to impact wildlife populations negatively, and their occurrence can alter the abundance, behavior, and activity patterns of native species. However, little is known about abundance and density of the free-ranging dogs that use protected areas. Here, we used camera trap data with an open-robust design mark–recapture model to estimate the number of dogs that used protected areas in Brazilian Atlantic Forest. We estimated the time period these dogs used the protected areas, and explored factors that influenced the probability of continued use (e.g., season, mammal richness, proportion of forest), while accounting for variation in detection probability. Dogs in the studied system were categorized as rural free-ranging, and their abundance varied widely across protected areas (0–73 individuals). Dogs used protected areas near human houses for longer periods (e.g., >50% of sampling occasions) compared to more distant areas. We found no evidence that their probability of continued use varied with season or mammal richness. Dog detection probability decreased linearly among occasions, possibly due to the owners confining their dogs after becoming aware of our presence. Comparing our estimates to those for native carnivoran, we found that dogs were three to 85 times more abundant than ocelots (Leopardus pardalis), two to 25 times more abundant than puma (Puma concolor), and approximately five times more abundant than the crab-eating fox (Cerdocyon thous). Combining camera trapping data with modern mark–recapture methods provides important demographic information on free-ranging dogs that can guide management strategies to directly control dogs' abundance and ranging behavior.

  13. BLM National Surface Management Agency: Area Polygons, Withdrawal Area Polygons, and Special Public Purpose Withdrawal Area Polygons

    Data.gov (United States)

    Federal Geographic Data Committee — The SMA implementation is comprised of one feature dataset, with several polygon feature classes, rather than a single feature class. SurfaceManagementAgency: The...

  14. The Influence of Long-Range Surface Forces on the Contact Angle of Nanometric Droplets and Bubbles.

    Science.gov (United States)

    Stocco, Antonio; Möhwald, Helmuth

    2015-11-03

    For a droplet or a bubble of dimensions below 100 nm, long-range surface forces such as long-range van der Waals forces can compete with capillarity, which leads to a size dependence of the contact angle. This is discussed in this work, where we also show that the effect cannot simply be described by a normalized line tension. We calculate interfacial profiles for typical values of van der Waals forces and discuss the role of long-range surface forces on the contact angle of nanobubbles and nanodrops.

  15. Impact of Surface Soil Moisture Variations on Radar Altimetry Echoes at Ku and Ka Bands in Semi-Arid Areas

    Directory of Open Access Journals (Sweden)

    Christophe Fatras

    2018-04-01

    Full Text Available Radar altimetry provides information on the topography of the Earth surface. It is commonly used for the monitoring not only sea surface height but also ice sheets topography and inland water levels. The radar altimetry backscattering coefficient, which depends on surface roughness and water content, can be related to surface properties such as surface soil moisture content. In this study, the influence of surface soil moisture on the radar altimetry echo and backscattering coefficient is analyzed over semi-arid areas. A semi-empirical model of the soil’s complex dielectric permittivity that takes into account that small-scale roughness and large-scale topography was developed to simulate the radar echoes. It was validated using waveforms acquired at Ku and Ka-bands by ENVISAT RA-2 and SARAL AltiKa respectively over several sites in Mali. Correlation coefficients ranging from 0.66 to 0.94 at Ku-band and from 0.27 to 0.96 at Ka-band were found. The increase in surface soil moisture from 0.02 to 0.4 (i.e., the typical range of variations in semi-arid areas increase the backscattering from 10 to 15 dB between the core of the dry and the maximum of the rainy seasons.

  16. Cyclic Brunn-Minkowski Inequalities for p -affine surface area | Zhao ...

    African Journals Online (AJOL)

    In 2010, Werner and Ye extended the denition for mixed p-affine surface area to all real numbers p. Following this, we establish some isoperimetric inequalities for the general mixed p-affine surface area. The results in special cases yield some of the recent results on inequalities of this type. Mathematics Subject ...

  17. 30 CFR 933.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

    Science.gov (United States)

    2010-07-01

    ... WITHIN EACH STATE NORTH CAROLINA § 933.761 Areas designated unsuitable for surface coal mining by Act of Congress. Part 761 of this chapter, Areas Designated Unsuitable for Coal Mining by Act of Congress, with the exception of §§ 761.11(c) and 761.12(f)(1), shall apply to surface coal mining and reclamation...

  18. Natural regeneration of deforested areas dominated by Pteridium aquilinum (L. Kuhn located in the serra da mantiqueira mountain range

    Directory of Open Access Journals (Sweden)

    Selma Cristina Ribeiro

    2013-03-01

    Full Text Available This study was set out with the objective of analyzing successional process in areas which are deforested and dominated by Pteridium aquilinum in the Serra da Mantiqueira mountain range, by researching the natural regeneration of shrub and tree species and evaluating both disturbance history and the edaphic conditions on the natural regeneration community. This research investigated two abandoned pasture areas in Bocaina de Minas county exposed to natural regeneration intervals ranging from six years (area named 6A to twenty years (area named 20A. The inventory occurred from sixty plots of 10 m², where all samples surveyed were between 0.15 m and 3 m high. All samples were identified and both the diameter in ground level and total height of the specimens were measured. The survey totaled 1,159 samples and 53 species. Melastomataceae was registered with the highest species richness and the highest specimen abundance. The two sampled areas showed species composition differences, with Jaccard similarity coefficient equal to 3.7%. The canonical correspondence analysis showed the correlations between natural regeneration stratum and non-labile phosphorus and clay in the 6A area. On the other hand, the 20A area showed correlations between plant regeneration and the K, P, Ca²+, Al³+ levels, with higher pH levels, and with the sum of exchangeable bases. In addition, the vegetation surveyed in area 20A was correlated with higher Pteridium population density. The results showed that the dominance of Pteridium aquilinum leads to successional process under inhibition, in which the ferns act negatively on the richness and abundance of shrub populations. It was also confirmed the Pteridium's affinity to steep areas, mainly in higher altitudes, where the soil is acid, as well as its preference to disturbed areas. Moreover, we highlight the fragilities of the mountain environments and the importance of preserving natural vegetation, as well as the bracken

  19. Surface and subsurface conditions in permafrost areas - a literature review

    International Nuclear Information System (INIS)

    Vidstrand, Patrik

    2003-02-01

    This report contains a summary of some of the information within existing technical and scientific literature on permafrost. Permafrost is viewed as one of the future climate driven process domains that may exist in Scandinavia, and that may give rise to significantly different surface and subsurface conditions than the present. Except for changes in the biosphere, permafrost may impact hydraulic, mechanical, and chemical subsurface processes and conditions. Permafrost and its influences on the subsurface conditions are thus of interest for the performance and safety assessments of deep geological waste repositories. The definition of permafrost is 'ground that stays at or below 0 deg C for at least two consecutive years'. Permafrost will effect the geological subsurface to some depth. How deep the permafrost may grow is a function of the heat balance, thermal conditions at the surface and within the ground, and the geothermal heat flux from the Earth's inner parts. The main chapters of the report summaries the knowledge on permafrost evolution, occurrence and distribution, and extracts information concerning hydrology and mechanical and chemical impacts due to permafrost related conditions. The results of a literature review are always dependent on the available literature. Concerning permafrost there is some literature available from investigations in the field of long-term repositories and some from mining industries. However, reports of these investigations are few and the bulk of permafrost literature comes from the science departments concerned with surficial processes (e.g. geomorphology, hydrology, agriculture, etc) and from engineering concerns, such as foundation of constructions and pipeline design. This focus within the permafrost research inevitably yields a biased but also an abundant amount of information on localised surficial processes and a limited amount on regional and deep permafrost characteristics. Possible conclusions are that there is

  20. Surface and subsurface conditions in permafrost areas - a literature review

    Energy Technology Data Exchange (ETDEWEB)

    Vidstrand, Patrik [Bergab, Goeteborg (Sweden)

    2003-02-01

    This report contains a summary of some of the information within existing technical and scientific literature on permafrost. Permafrost is viewed as one of the future climate driven process domains that may exist in Scandinavia, and that may give rise to significantly different surface and subsurface conditions than the present. Except for changes in the biosphere, permafrost may impact hydraulic, mechanical, and chemical subsurface processes and conditions. Permafrost and its influences on the subsurface conditions are thus of interest for the performance and safety assessments of deep geological waste repositories. The definition of permafrost is 'ground that stays at or below 0 deg C for at least two consecutive years'. Permafrost will effect the geological subsurface to some depth. How deep the permafrost may grow is a function of the heat balance, thermal conditions at the surface and within the ground, and the geothermal heat flux from the Earth's inner parts. The main chapters of the report summaries the knowledge on permafrost evolution, occurrence and distribution, and extracts information concerning hydrology and mechanical and chemical impacts due to permafrost related conditions. The results of a literature review are always dependent on the available literature. Concerning permafrost there is some literature available from investigations in the field of long-term repositories and some from mining industries. However, reports of these investigations are few and the bulk of permafrost literature comes from the science departments concerned with surficial processes (e.g. geomorphology, hydrology, agriculture, etc) and from engineering concerns, such as foundation of constructions and pipeline design. This focus within the permafrost research inevitably yields a biased but also an abundant amount of information on localised surficial processes and a limited amount on regional and deep permafrost characteristics. Possible conclusions are that

  1. Target surface area effects on hot electron dynamics from high intensity laser-plasma interactions

    Science.gov (United States)

    Zulick, C.; Raymond, A.; McKelvey, A.; Chvykov, V.; Maksimchuk, A.; Thomas, A. G. R.; Willingale, L.; Yanovsky, V.; Krushelnick, K.

    2016-06-01

    Reduced surface area targets were studied using an ultra-high intensity femtosecond laser in order to determine the effect of electron sheath field confinement on electron dynamics. X-ray emission due to energetic electrons was imaged using a {K}α imaging crystal. Electrons were observed to travel along the surface of wire targets, and were slowed mainly by the induced fields. Targets with reduced surface areas were correlated with increased hot electron densities and proton energies. Hybrid Vlasov-Fokker-Planck simulations demonstrated increased electric sheath field strength in reduced surface area targets.

  2. Non-activated high surface area expanded graphite oxide for supercapacitors

    Energy Technology Data Exchange (ETDEWEB)

    Vermisoglou, E.C.; Giannakopoulou, T.; Romanos, G.E.; Boukos, N.; Giannouri, M. [Institute of Nanoscience and Nanotechnology “Demokritos”, 153 43 Ag. Paraskevi, Attikis (Greece); Lei, C.; Lekakou, C. [Division of Mechanical, Medical, and Aerospace Engineering, Faculty of Engineering and Physical Sciences, University of Surrey, Guildford GU2 7XH (United Kingdom); Trapalis, C., E-mail: c.trapalis@inn.demokritos.gr [Institute of Nanoscience and Nanotechnology “Demokritos”, 153 43 Ag. Paraskevi, Attikis (Greece)

    2015-12-15

    Graphical abstract: - Highlights: • One-step exfoliation and reduction of graphite oxide via microwave irradiation. • Effect of pristine graphite (type, flake size) on the microwave expanded material. • Effect of pretreatment and oxidation cycles on the produced expanded material. • Expanded graphene materials with high BET surface areas (940 m{sup 2}/g–2490 m{sup 2}/g). • Non-activated graphene based materials suitable for supercapacitors. - Abstract: Microwave irradiation of graphite oxide constitutes a facile route toward production of reduced graphene oxide, since during this treatment both exfoliation and reduction of graphite oxide occurs. In this work, the effect of pristine graphite (type, size of flakes), pretreatment and oxidation cycles on the finally produced expanded material was examined. All the types of graphite that were tested afforded materials with high BET surface areas ranging from 940 m{sup 2}/g to 2490 m{sup 2}/g, without intervening an activation stage at elevated temperature. SEM and TEM images displayed exfoliated structures, where the flakes were significantly detached and curved. The quality of the reduced graphene oxide sheets was evidenced both by X-ray photoelectron spectroscopy and Raman spectroscopy. The electrode material capacitance was determined via electrochemical impedance spectroscopy and cyclic voltammetry. The materials with PEDOT binder had better performance (∼97 F/g) at low operation rates while those with PVDF binder performed better (∼20 F/g) at higher rates, opening up perspectives for their application in supercapacitors.

  3. Measurement of the specific surface area of loose copper deposit by electrochemical methods

    Directory of Open Access Journals (Sweden)

    E. A. Dolmatova

    2016-07-01

    Full Text Available In the work the surface area of the electrode with dispersed copper deposit obtained within 30 seconds was evaluated by techniques of chronopotentiometry (CPM and impedance spectroscopy. In method CPM the electrode surface available for measurement depends on the value of the polarizing current. At high currents during the transition time there is a change of surface relief that can not determine the full surface of loose deposit. The electrochemical impedance method is devoid of this shortcoming since the measurements are carried out in indifferent electrolyte in the absence of current. The area measured by the impedance is tens of times higher than the value obtained by chronopotentiometry. It is found that from a solution containing sulfuric acid the deposits form with a high specific surface area. Based on these data it was concluded that the method of impedance spectroscopy can be used to measure in situ the surface area of the dispersed copper deposits.

  4. The protection of urban areas from surface wastewater pollutions

    Directory of Open Access Journals (Sweden)

    Vialkova Elena

    2017-01-01

    Full Text Available In this paper it considered the problem of collection, treatment and discharge into waters of rain and melted wastewater. To reduce the load on the combined sewer system, there are engineering solutions collect rain and melt water for use in the irrigation of lawns and green spaces. Research carried out at the department “Water supply and sanitation”, (Russia, confirm the high pollution concentrations of meltwater and rainfall in urban arias. Series of measurements of heavy metal in rainwater runoff carried out in Hungary demonstrates clearly the differences in concentrations in the function of distance from the edge of the road. Also differences are introduced between pollution concentrations in runoff water from within and outside urban traffic roads. The quality of snow cover, forming meltwater is observed to be changing in dependence on roadway location. Quality characteristics of surface runoff and its sediments can be effectively improved with super-high frequency radiation (SHF treatment which is presented in this paper.

  5. Diurnal Cycles of High Resolution Land Surface Temperatures (LSTs) Determined from UAV Platforms Across a Range of Surface Types

    Science.gov (United States)

    McCabe, M.; Rosas Aguilar, J.; Parkes, S. D.; Aragon, B.

    2017-12-01

    Observation of land surface temperature (LST) has many practical uses, from studying boundary layer dynamics and land-atmosphere coupling, to investigating surface properties such as soil moisture status, heat stress and surface heat fluxes. Typically, LST is observed via satellite based sensors such as LandSat or via point measurements using IR radiometers. These measurements provide either good spatial coverage and resolution or good temporal coverage. However, neither are able to provide the needed spatial and temporal resolution for many of the research applications described above. Technological developments in the use of Unmanned Aerial Vehicles (UAVs), together with small thermal frame cameras, has enabled a capacity to overcome this spatiotemporal constraint. Utilising UAV platforms to collect LST measurements across diurnal cycles provides an opportunity to study how meteorological and surface properties vary in both space and time. Here we describe the collection of LST data from a multi-rotor UAV across a study domain that is observed multiple times throughout the day. Flights over crops of Rhodes grass and alfalfa, along with a bare desert surface, were repeated with between 8 and 11 surveys covering the period from early morning to sunset. Analysis of the collected thermal imagery shows that the constructed LST maps illustrate a strong diurnal cycle consistent with expected trends, but with considerable spatial and temporal variability observed within and between the different domains. These results offer new insights into the dynamics of land surface behavior in both dry and wet soil conditions and at spatiotemporal scales that are unable to be replicated using traditional satellite platforms.

  6. 30 CFR 905.764 - Process for designating areas unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... surface coal mining operations. 905.764 Section 905.764 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE CALIFORNIA § 905.764 Process for designating areas unsuitable for surface coal mining... coal mining operations beginning one year after the effective date of this program. ...

  7. 30 CFR 947.764 - Process for designating areas unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... surface coal mining operations. 947.764 Section 947.764 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE WASHINGTON § 947.764 Process for designating areas unsuitable for surface coal mining... coal mining and reclamation operations. (b) The Secretary shall notify the Washington Department of...

  8. 30 CFR 903.764 - Process for designating areas unsuitable for surface coal mining operations.

    Science.gov (United States)

    2010-07-01

    ... surface coal mining operations. 903.764 Section 903.764 Mineral Resources OFFICE OF SURFACE MINING... WITHIN EACH STATE ARIZONA § 903.764 Process for designating areas unsuitable for surface coal mining... coal mining operations beginning June 24, 1996, one year after the effective date of this program. ...

  9. Synthetic microfluidic paper: high surface area and high porosity polymer micropillar arrays.

    Science.gov (United States)

    Hansson, Jonas; Yasuga, Hiroki; Haraldsson, Tommy; van der Wijngaart, Wouter

    2016-01-21

    We introduce Synthetic Microfluidic Paper, a novel porous material for microfluidic applications that consists of an OSTE polymer that is photostructured in a well-controlled geometry of slanted and interlocked micropillars. We demonstrate the distinct benefits of Synthetic Microfluidic Paper over other porous microfluidic materials, such as nitrocellulose, traditional paper and straight micropillar arrays: in contrast to straight micropillar arrays, the geometry of Synthetic Microfluidic Paper was miniaturized without suffering capillary collapse during manufacturing and fluidic operation, resulting in a six-fold increased internal surface area and a three-fold increased porous fraction. Compared to commercial nitrocellulose materials for capillary assays, Synthetic Microfluidic Paper shows a wider range of capillary pumping speed and four times lower device-to-device variation. Compared to the surfaces of the other porous microfluidic materials that are modified by adsorption, Synthetic Microfluidic Paper contains free thiol groups and has been shown to be suitable for covalent surface chemistry, demonstrated here for increasing the material hydrophilicity. These results illustrate the potential of Synthetic Microfluidic Paper as a porous microfluidic material with improved performance characteristics, especially for bioassay applications such as diagnostic tests.

  10. Evaluation of an atmospheric model with surface and ABL meteorological data for energy applications in structured areas

    Science.gov (United States)

    Triantafyllou, A. G.; Kalogiros, J.; Krestou, A.; Leivaditou, E.; Zoumakis, N.; Bouris, D.; Garas, S.; Konstantinidis, E.; Wang, Q.

    2018-03-01

    This paper provides the performance evaluation of the meteorological component of The Air Pollution Model (TAPM), a nestable prognostic model, in predicting meteorological variables in urban areas, for both its surface layer and atmospheric boundary layer (ABL) turbulence parameterizations. The model was modified by incorporating four urban land surface types, replacing the existing single urban surface. Control runs were carried out over the wider area of Kozani, an urban area in NW Greece. The model was evaluated for both surface and ABL meteorological variables by using measurements of near-surface and vertical profiles of wind and temperature. The data were collected by using monitoring surface stations in selected sites as well as an acoustic sounder (SOnic Detection And Ranging (SODAR), up to 300 m above ground) and a radiometer profiler (up to 600 m above ground). The results showed the model demonstrated good performance in predicting the near-surface meteorology in the Kozani region for both a winter and a summer month. In the ABL, the comparison showed that the model's forecasts generally performed well with respect to the thermal structure (temperature profiles and ABL height) but overestimated wind speed at the heights of comparison (mostly below 200 m) up to 3-4 ms-1.

  11. Environmental and geochemical assessment of surface sediments on irshansk ilmenite deposit area

    Directory of Open Access Journals (Sweden)

    Наталия Олеговна Крюченко

    2015-03-01

    Full Text Available It is revealed the problem of pollution of surface sediments of Irshansk ilmenite deposit area of various chemical elements hazard class (Mn, V, Ba, Ni, Co, Cr, Mo, Cu, Pb, Zn. It is determined its average content in surface sediments of various functional areas (forest and agricultural land, flood deposits, reclaimed land, calculated geochemical criteria, so given ecological and geochemical assessment of area

  12. Turbulent heat transfer on a permeable surface in the range of supercritical gas injections

    International Nuclear Information System (INIS)

    Kichatov, B.V.; Polyaev, V.M.

    1997-01-01

    Gas injection in a permeable surface is used as one of the most perspective ways of thermal protection. Forcing back of the boundary layer from the surface takes place by injection, whereby the friction coefficients and heat exchange are decreased. By certain injection parameter, which is called critical, there takes place the complete forcing back of the boundary layer from the surface. However the process of friction and heat exchange degeneration proceeds nonuniformly. This article is devoted to explanation of the above notice. Analysis of the problem is based on the limiting relative law of heat exchange and friction for a turbulent boundary layer

  13. Rb-Sr geochronolgy of the Jervois Range area in the eastern part of the Arunta Block, NT

    International Nuclear Information System (INIS)

    Black, L.P.

    1980-01-01

    New Rb-Sr isotopic data are presented for the Jervois Range area in the eastern part of the Arunta Block. The post-metamorphic Jinka and Jervois Granites yield an age of about 1750 m.y. An alaskitic granite is dated at about 1460 m.y. Pegmatite formation occurred about 1660 m.y. ago. Mineral ages are generally younger than total-rock ages, but no values significantly less than that of the alaskitic granite were found. This means that the Alice Springs Orogeny, which extensively reset large areas of the Arunta Block to the west, did not effect the Jervois area. In this and other geochronological comparisons, the Jervois area seems more akin to the rocks of the Tennant Creek Block, 400 km to the northwest, than to those of the Arunta Block

  14. Atlantic Test Range (ATR)

    Data.gov (United States)

    Federal Laboratory Consortium — ATR controls fully-instrumented and integrated test ranges that provide full-service support for cradle-to-grave testing. Airspace and surface target areas are used...

  15. Injection molding of nanopatterned surfaces in the sub-micrometer range with induction heating aid

    DEFF Research Database (Denmark)

    Menotti, Stefano; Hansen, Hans Nørgaard; Bissacco, Giuliano

    2014-01-01

    Replication of sub-micrometer structures by injection molding leads to special requirements for the mold in order to ensure proper replica and acceptable cycle time. This paper investigates the applicability of induction heating embedded into the mold for the improvement of nanopattern replication...... as materials, and heating parameters were investigated after a preliminary optimization with standard heating conditions. The replicated surfaces were quantitatively characterized by atomic force microscopy using specific three-dimensional surface amplitude parameters and qualitatively inspected by scanning...

  16. Development of cortical thickness and surface area in autism spectrum disorder

    Directory of Open Access Journals (Sweden)

    Vincent T. Mensen

    2017-01-01

    Full Text Available Autism spectrum disorder (ASD is a neurodevelopmental disorder often associated with changes in cortical volume. The constituents of cortical volume – cortical thickness and surface area – have separable developmental trajectories and are related to different neurobiological processes. However, little is known about the developmental trajectories of cortical thickness and surface area in ASD. In this magnetic resonance imaging (MRI study, we used an accelerated longitudinal design to investigate the cortical development in 90 individuals with ASD and 90 typically developing controls, aged 9 to 20 years. We quantified cortical measures using the FreeSurfer software package, and then used linear mixed model analyses to estimate the developmental trajectories for each cortical measure. Our primary finding was that the development of surface area follows a linear trajectory in ASD that differs from typically developing controls. In typical development, we found a decline in cortical surface area between the ages of 9 and 20 that was absent in ASD. We found this pattern in all regions where developmental trajectories for surface area differed between groups. When we applied a more stringent correction that takes the interdependency of measures into account, this effect on cortical surface area retained significance for left banks of superior temporal sulcus, postcentral area, and right supramarginal area. These areas have previously been implicated in ASD and are involved in the interpretation and processing of audiovisual social stimuli and distinction between self and others. Although some differences in cortical volume and thickness were found, none survived the more stringent correction for multiple testing. This study underscores the importance of distinguishing between cortical surface area and thickness in investigating cortical development, and suggests the development of cortical surface area is of importance to ASD.

  17. Magnetic frustration, short-range correlations and the role of the paramagnetic Fermi surface of PdCrO2

    Science.gov (United States)

    Billington, David; Ernsting, David; Millichamp, Thomas E.; Lester, Christopher; Dugdale, Stephen B.; Kersh, David; Duffy, Jonathan A.; Giblin, Sean R.; Taylor, Jonathan W.; Manuel, Pascal; Khalyavin, Dmitry D.; Takatsu, Hiroshi

    2015-01-01

    Frustrated interactions exist throughout nature, with examples ranging from protein folding through to frustrated magnetic interactions. Whilst magnetic frustration is observed in numerous electrically insulating systems, in metals it is a rare phenomenon. The interplay of itinerant conduction electrons mediating interactions between localised magnetic moments with strong spin-orbit coupling is likely fundamental to these systems. Therefore, knowledge of the precise shape and topology of the Fermi surface is important in any explanation of the magnetic behaviour. PdCrO2, a frustrated metallic magnet, offers the opportunity to examine the relationship between magnetic frustration, short-range magnetic order and Fermi surface topology. By mapping the short-range order in reciprocal space and experimentally determining the electronic structure, we have identified the dual role played by the Cr electrons in which the itinerant ones on the nested paramagnetic Fermi surface mediate the frustrated magnetic interactions between local moments. PMID:26206589

  18. Identification of air and sea-surface targets with a laser range profiler

    NARCIS (Netherlands)

    Heuvel, J.C. van den; Schoemaker, R.M.; Schleijpen, H.M.A.

    2009-01-01

    Current coastal operations have to deal with threats at short range in complex environments with both neutral and hostile targets. There is a need for fast identification, which is possible with a laser range profiler. A number of field trials have been conducted to validate the concept of

  19. Surface deformation measured with interferometric synthetic aperture radar: Case studies of basin and range and Garlock-San Andreas fault

    Science.gov (United States)

    Greene, Fernando

    Interferometric Synthetic Aperture Radar (InSAR) and Global Positioning System (GPS) is widely used to detect ground deformation from varieties of geophysical origins. However, most studies lack the spatial and temporal resolutions to better characterize such observations. The purpose of this research is to use multi-track satellite radar imagery to generate time series to study and monitor vertical ground deformation over large regions such as the Nevada portion of the Basin and Range Province and the western end of the Mojave Desert. We developed an innovative method to remove horizontal movements from InSAR line-of-sight (LOS) observations using a GPS velocity field and subsequently combine the multi-track imagery resulting in one single high spatial resolution map of observed vertical crustal and surface movements. By implementing this technique we detect vertical deformation signals with short and intermediate wavelength signals associated to tectonic processes such as interseismic and postseismic deformation. In Central Nevada Seismic Belt we detect in three independent orbits a broad area of uplift that confirms results of previous studies that associate the origin of this signal to post-seimic deformation of the historic earthquakes at this region. In south-central Nevada we detect several valleys that show a gradual eastward tilt of the valley floors due to deep geodynamical processes. The valleys located at the eastern side of Ruby Mountains show a range decrease that could indicate uplift related to magma intrusion or post-seismic deformation due to older, unrecognized earthquakes. In the Big Bend segment in southern California we detect vertical uplift as expected by mechanical models of interseismic deformation. Additionaly all our velocity maps reveal small wavelength deformation signals of anthropogenic origin.

  20. Influence of surface position along the working range of conoscopic holography sensors on dimensional verification of AISI 316 wire EDM machined surfaces.

    Science.gov (United States)

    Fernández, Pedro; Blanco, David; Rico, Carlos; Valiño, Gonzalo; Mateos, Sabino

    2014-03-06

    Conoscopic holography (CH) is a non-contact interferometric technique used for surface digitization which presents several advantages over other optical techniques such as laser triangulation. Among others, the ability for the reconstruction of high-sloped surfaces stands out, and so does its lower dependence on surface optical properties. Nevertheless, similarly to other optical systems, adjustment of CH sensors requires an adequate selection of configuration parameters for ensuring a high quality surface digitizing. This should be done on a surface located as close as possible to the stand-off distance by tuning frequency (F) and power (P) until the quality indicators Signal-to-Noise Ratio (SNR) and signal envelope (Total) meet proper values. However, not all the points of an actual surface are located at the stand-off distance, but they could be located throughout the whole working range (WR). Thus, the quality of a digitized surface may not be uniform. The present work analyses how the quality of a reconstructed surface is affected by its relative position within the WR under different combinations of the parameters F and P. Experiments have been conducted on AISI 316 wire EDM machined flat surfaces. The number of high-quality points digitized as well as distance measurements between different surfaces throughout the WR allowed for comparing the metrological behaviour of the CH sensor with respect to a touch probe (TP) on a CMM.

  1. Influence of Surface Position along the Working Range of Conoscopic Holography Sensors on Dimensional Verification of AISI 316 Wire EDM Machined Surfaces

    Directory of Open Access Journals (Sweden)

    Pedro Fernández

    2014-03-01

    Full Text Available Conoscopic holography (CH is a non-contact interferometric technique used for surface digitization which presents several advantages over other optical techniques such as laser triangulation. Among others, the ability for the reconstruction of high-sloped surfaces stands out, and so does its lower dependence on surface optical properties. Nevertheless, similarly to other optical systems, adjustment of CH sensors requires an adequate selection of configuration parameters for ensuring a high quality surface digitizing. This should be done on a surface located as close as possible to the stand-off distance by tuning frequency (F and power (P until the quality indicators Signal-to-Noise Ratio (SNR and signal envelope (Total meet proper values. However, not all the points of an actual surface are located at the stand-off distance, but they could be located throughout the whole working range (WR. Thus, the quality of a digitized surface may not be uniform. The present work analyses how the quality of a reconstructed surface is affected by its relative position within the WR under different combinations of the parameters F and P. Experiments have been conducted on AISI 316 wire EDM machined flat surfaces. The number of high-quality points digitized as well as distance measurements between different surfaces throughout the WR allowed for comparing the metrological behaviour of the CH sensor with respect to a touch probe (TP on a CMM.

  2. Woody vegetation and succession on the Fonde surface mine demonstration area, Bell County, Kentucky

    International Nuclear Information System (INIS)

    Wade, G.L.; Thompson, R.L.

    1999-01-01

    The long term impact of surface mining on vegetation and plant succession has always been of concern to environmentalists and residents of Appalachia. The Fonde Surface Mine Demonstration Area is a 7.3-ha, NE-NW-aspect contour coal mine at an elevation of 562 m. It was reclaimed in 1965 to show state-of-the-art surface mine reclamation techniques consistent with then-current law and regulations after coal mining in 1959 and 1963. The mine spoils were lightly graded to control erosion and crates a bench with water control and two sediment ponds. Soil pH ranged from 2.8 to 5.9. About 80 percent of the mine was planted with 18 tree and shrub species including plantations of mixed pine, mixed hardwoods, black locust, and shrubs for wildlife. In a complete floristic inventory conducted 25 years later, the authors found the woody flora consisted of 34 families, 53 genera, and 70 species including 7 exotics. This inventory of the Fonde mine shows that a diverse forest vegetation can be reestablished after extreme disturbances in Appalachia. Black locust, yellow poplar, and Virginia pine reproduction varied significantly among plantation types. Canopy tree species significantly affected ground layer cover, total species richness, number of tree seedling species, and total number of tree seedlings present. Mine soil type affected ground layer percent cover and total species richness. Pre-SMCRA (Surface Mining Control and Reclamation Act of 1977) reclaimed and inventoried mines can be used to evaluate biodiversity on post-SMCRA mines

  3. Using Range-Wide Abundance Modeling to Identify Key Conservation Areas for the Micro-Endemic Bolson Tortoise (Gopherus flavomarginatus.

    Directory of Open Access Journals (Sweden)

    Cinthya A Ureña-Aranda

    Full Text Available A widespread biogeographic pattern in nature is that population abundance is not uniform across the geographic range of species: most occurrence sites have relatively low numbers, whereas a few places contain orders of magnitude more individuals. The Bolson tortoise Gopherus flavomarginatus is endemic to a small region of the Chihuahuan Desert in Mexico, where habitat deterioration threatens this species with extinction. In this study we combined field burrows counts and the approach for modeling species abundance based on calculating the distance to the niche centroid to obtain range-wide abundance estimates. For the Bolson tortoise, we found a robust, negative relationship between observed burrows abundance and distance to the niche centroid, with a predictive capacity of 71%. Based on these results we identified four priority areas for the conservation of this microendemic and threatened tortoise. We conclude that this approach may be a useful approximation for identifying key areas for sampling and conservation efforts in elusive and rare species.

  4. Using Range-Wide Abundance Modeling to Identify Key Conservation Areas for the Micro-Endemic Bolson Tortoise (Gopherus flavomarginatus).

    Science.gov (United States)

    Ureña-Aranda, Cinthya A; Rojas-Soto, Octavio; Martínez-Meyer, Enrique; Yáñez-Arenas, Carlos; Landgrave Ramírez, Rosario; Espinosa de los Monteros, Alejandro

    2015-01-01

    A widespread biogeographic pattern in nature is that population abundance is not uniform across the geographic range of species: most occurrence sites have relatively low numbers, whereas a few places contain orders of magnitude more individuals. The Bolson tortoise Gopherus flavomarginatus is endemic to a small region of the Chihuahuan Desert in Mexico, where habitat deterioration threatens this species with extinction. In this study we combined field burrows counts and the approach for modeling species abundance based on calculating the distance to the niche centroid to obtain range-wide abundance estimates. For the Bolson tortoise, we found a robust, negative relationship between observed burrows abundance and distance to the niche centroid, with a predictive capacity of 71%. Based on these results we identified four priority areas for the conservation of this microendemic and threatened tortoise. We conclude that this approach may be a useful approximation for identifying key areas for sampling and conservation efforts in elusive and rare species.

  5. Squeezing Molecularly thin Lubricant Films between curved Corrugated Surfaces with long range Elasticity

    DEFF Research Database (Denmark)

    Sivebæk, Ion Marius; Samoilov, Vladimir N.; Persson, Bo N. J.

    2010-01-01

    one being associated with devastating wear progress. The properties of alkane lubricants confined between two approaching solids are investigated by a model that accounts for the roughness, curvature and elastic properties of the solid surfaces. We consider linear alkanes of different chain lengths, C......The present work investigates the ability of two nm thick lubrication films to stay in a contact and thereby to prevent excessive wear of the surfaces. At this thickness the film is no longer a fluid but it is the very important intermediate between the lubricated and the dry regimes, the latter......3H8, C4H10, C8H18, C9H20, C10H22, C14H30 and C16H34, confined between corrugated gold surfaces. Well defined molecular layers develop in the lubricant film when the width is of the order of a few atomic diameters. An external squeezing pressure induces discontinuous, thermally activated changes...

  6. Effect of specific surface area of MWCNTS on surface roughness and delamination in drilling Epoxy/Glass Fabric Composite

    Science.gov (United States)

    Ponnuvel, S.; Ananth, M. Prem

    2018-03-01

    In this study the effect of specific surface area of the MWCNTs on the drilled hole qualities was investigated. Epoxy araldite LY556 with hardener HY951 and E-glass coarse plain weave fabric are used for the fabrication of reference material (specimen A). Multi-WalledCarbon Nanotubes (MWCNTs) with diameters fabrication of study materials, namely specimen B and specimen C respectively. In specimen B the epoxy resin was filled with MWCNTs having a specific surface area >500 m2 g‑1. MWCNTs in specimen C had a specific surface area >110 m2 g‑1. Drilling experiments were conducted on all the three specimens. Two dimensional delamination factor and the surface roughness of the inner wall of the drilled holes were investigated using Grey Relational Analysis (GRA) and Analysis of variance (ANOVA). Two dimensional delamination factor showed better performance from specimen B and specimen C in comparison with specimen A suggesting improvement in the bonding between epoxy and the glass fiber in the presence of MWCNTs. Similar observations were made for surface roughness of the inner wall of the drilled holes at 1250 rpm. Whereas the presence of MWCNTs (Specimen B and specimen C) produced poor surface finish at 500 rpm in comparison with specimen A. Variations in the hole quality characteristics between specimen B and specimen C was marginal with better observations in specimen C.

  7. Large-area electromagnetic enhancement by a resonant excitation of surface waves on a metallic surface with periodic subwavelength patterns.

    Science.gov (United States)

    Zhang, Xin; Liu, Haitao; Zhong, Ying

    2013-10-07

    We theoretically investigate the electromagnetic enhancement on a metallic surface patterned with periodic subwavelength structures. Fully-vectorial calculations show a large-area electromagnetic enhancement (LAEE) on the surface, which strongly contrasts with the previously reported "hot spots" that occur in specific tiny regions and which relieves the rigorous requirement of the nano-scale location of sample molecules. The LAEE allows for designing more practicable substrates for many enhanced-spectra applications. By building up microscopic models, the LAEE is shown due to a resonant excitation of surface waves that include both the surface plasmon polariton (SPP) and a quasi-cylindrical wave (QCW). The surface waves propagate on the substrate over a long distance and thus greatly enlarge the area of electromagnetic enhancement compared to the nano-sized hot spots caused by localized modes. Gain medium is introduced to further strengthen the large-area surface-wave resonance, with which an enhancement factor (EF) of electric-field intensity up to a few thousands is achieved.

  8. Low Friction and Wear Surface for Application over a Wide Range of Temperature

    National Research Council Canada - National Science Library

    Bhattacharya, Rabi

    1997-01-01

    ...) and Transmission electron microscopy (TEM), both before and after exposure to high temperatures (up to 700 deg C) in air. Friction measurements were performed at temperatures in the range of room temperature to 700 deg C in air...

  9. Photonic bandgap structures for guiding of long-range surface plasmon polaritons

    DEFF Research Database (Denmark)

    Leosson, K.; Nikolajsen, T.; Boltasseva, Alexandra

    2003-01-01

    We present the first observations of long-range plasmon polariton guiding in photonic bandgap structures. The transmission of waveguide structures is characterized at telecommunication wavelengths and a propagation loss below 4 dB/mm is determined.......We present the first observations of long-range plasmon polariton guiding in photonic bandgap structures. The transmission of waveguide structures is characterized at telecommunication wavelengths and a propagation loss below 4 dB/mm is determined....

  10. Surface area loss and increased sphericity account for the splenic entrapment of subpopulations of Plasmodium falciparum ring-infected erythrocytes.

    Directory of Open Access Journals (Sweden)

    Innocent Safeukui

    Full Text Available Ex vivo perfusion of human spleens revealed innate retention of numerous cultured Plasmodium falciparum ring-infected red blood cells (ring-iRBCs. Ring-iRBC retention was confirmed by a microsphiltration device, a microbead-based technology that mimics the mechanical filtering function of the human spleen. However, the cellular alterations underpinning this retention remain unclear. Here, we use ImageStream technology to analyze infected RBCs' morphology and cell dimensions before and after fractionation with microsphiltration. Compared to fresh normal RBCs, the mean cell membrane surface area loss of trophozoite-iRBCs, ring-iRBCs and uninfected co-cultured RBCs (uRBCs was 14.2% (range: 8.3-21.9%, 9.6% (7.3-12.2% and 3.7% (0-8.4, respectively. Microsphilters retained 100%, ∼50% and 4% of trophozoite-iRBCs, ring-iRBCs and uRBCs, respectively. Retained ring-iRBCs display reduced surface area values (estimated mean, range: 17%, 15-18%, similar to the previously shown threshold of surface-deficient RBCs retention in the human spleen (surface area loss: >18%. By contrast, ring-iRBCs that successfully traversed microsphilters had minimal surface area loss and normal sphericity, suggesting that these parameters are determinants of their retention. To confirm this hypothesis, fresh normal RBCs were exposed to lysophosphatidylcholine to induce a controlled loss of surface area. This resulted in a dose-dependent retention in microsphilters, with complete retention occurring for RBCs displaying >14% surface area loss. Taken together, these data demonstrate that surface area loss and resultant increased sphericity drive ring-iRBC retention in microsphilters, and contribute to splenic entrapment of a subpopulation of ring-iRBCs. These findings trigger more interest in malaria research fields, including modeling of infection kinetics, estimation of parasite load, and analysis of risk factors for severe clinical forms. The determination of the threshold of

  11. Rapid fabrication of large-area, corrosion-resistant superhydrophobic Mg alloy surfaces.

    Science.gov (United States)

    Xu, Wenji; Song, Jinlong; Sun, Jing; Lu, Yao; Yu, Ziyuan

    2011-11-01

    A superhydrophobic magnesium (Mg) alloy surface was successfully fabricated via a facile electrochemical machining process, and subsequently covered with a fluoroalkylsilane (FAS) film. The surface morphologies and chemical compositions were investigated using a scanning electron microscope (SEM) equipped with an energy-dispersive spectroscopy (EDS) and a Fourier-transform infrared spectrophotometer (FTIR). The results show hierarchal rough structures and an FAS film with a low surface energy on the Mg alloy surfaces, which confers good superhydrophobicity with a water contact angle of 165.2° and a water tilting angle of approximately 2°. The processing conditions, such as the processing time and removal rate per unit area at a constant removal mass per unit area, were investigated to determine their effects on the superhydrophobicity. Interestingly, when the removal mass per unit area is constant at approximately 11.10 mg/cm(2), the superhydrophobicity does not change with the removal rate per unit area. Therefore, a superhydrophobic Mg alloy surface can be rapidly fabricated based on this property. A large-area superhydrophobic Mg alloy surface was also fabricated for the first time using a small-area moving cathode. The corrosion resistance and durability of the superhydrophobic surfaces were also examined.

  12. Relationship between Mineral Soil Surface Area and the Biological Degradation of Biosolids Added to Soil

    Directory of Open Access Journals (Sweden)

    Dongqi Wen

    2015-12-01

    Full Text Available Geochemical and biological processes that operate in the soil matrix and on the soil surface are important to the degradation of biosolids in soil. Due to the large surface area of soils it is assumed that the microbial ecology is associated with mineral soil surface area. The total mineral surface areas were determined for soils from eight different fields selected from a long term study (1972–2006 of annual biosolids application to 41 fields in central Illinois varying in size from 3.6 to 66 ha. The surface areas for the soils varied from 1 to 9 m2/g of soil. The biological degradation rates for the eight soils were determined using a biological degradation rate model (DRM and varied from 0.02 to 0.20/year−1. Regression analysis revealed that the degradation rate was positively associated with mineral soil surface area (1 m2/g produces 0.018 year−1 increase in the degradation rate. The annual soil sequestration rate was calculated to increase from 1% to 6% when the soil total surface area increased from 1 to 9 m2/g of soil. Therefore, land application of biosolids is an effective way to enhance carbon sequestration in soils and reduce greenhouse gas emissions.

  13. Preventing protein adsorption from a range of surfaces using an aqueous fish protein extract

    DEFF Research Database (Denmark)

    Pillai, Saju; Arpanaei, Ayyoob; Meyer, Rikke L.

    2009-01-01

    We utilize an aqueous extract of fish proteins (FPs) as a coating for minimizing the adsorption of fibrinogen (Fg) and human serum albumin (HSA). The surfaces include stainless steel (SS), gold (Au), silicon dioxide (SiO2), and poly(styrene) (PS). The adsorption processes (kinetics and adsorbed...

  14. On the diurnal ranges of Sea Surface Temperature (SST) in the ...

    Indian Academy of Sciences (India)

    The variability of sea surface temperature (SST) is widely studied due to its large impact on ocean–atmosphere interaction. Kawai and Wada. (2007) provides an excellent review on the impor- tance of the diurnal variability of SST on air– sea interaction. Diurnal variations in the SST affect longer time-scale variability events ...

  15. Streamlined Approach for Environmental Restoration Plan for Corrective Action Unit 425: Area 9 Main Lake Construction Debris Disposal Area, Tonopah Test Range, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    K. B. Campbell

    2002-04-01

    This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the action necessary for the closure of Corrective Action Unit (CAU) 425, Area 9 Main Lake Construction Debris Disposal Area. This CAU is currently listed in Appendix III of the Federal Facility Agreement and Consent Order (FFACO, 1996). This site will be cleaned up under the SAFER process since the volume of waste exceeds the 23 cubic meters (m{sup 3}) (30 cubic yards [yd{sup 3}]) limit established for housekeeping sites. CAU 425 is located on the Tonopah Test Range (TTR) and consists of one Corrective Action Site (CAS) 09-08-001-TA09, Construction Debris Disposal Area (Figure 1). CAS 09-08-001-TA09 is an area that was used to collect debris from various projects in and around Area 9. The site is located approximately 81 meters (m) (265 feet [ft]) north of Edwards Freeway northeast of Main Lake on the TTR. The site is composed of concrete slabs with metal infrastructure, metal rebar, wooden telephone poles, and concrete rubble from the Hard Target and early Tornado Rocket sled tests. Other items such as wood scraps, plastic pipes, soil, and miscellaneous nonhazardous items have also been identified in the debris pile. It is estimated that this site contains approximately 2280 m{sup 3} (3000 yd{sup 3}) of construction-related debris.

  16. Dem Assessment Derived from Close Range Photogrammetry: a Case Study from Kadavur Area, Karur District, Tamil Nadu, India

    Science.gov (United States)

    Anbarasan, S.; Sakthivel, R.

    2012-07-01

    Close-Range Photogrammetry is an accurate, cost effective technique of collecting measurements of real world objects and conditions, directly from photographs. Photogrammetry utilizes digital images to obtain accurate measurements and geometric data of the object or area of interest, in order to provide spatial information for Engineering design, spatial surveys or 3D modeling. The benefits of close-range Photogrammetry over other field procedures are purported to be: Increased accuracy; complete as-built information; reduced costs; reduced on-site time; and effective for small and large projects. The same basic principle of traditional Aerial Photogrammetry can be applied to stereoscopic pictures taken from lower altitudes or from the ground. Terrestrial, ground-based, and close-range are all descriptive terms that refer to photos taken with an object-to-camera distance less than 300m (1000 feet). (Matthews, N.A, 2008). Close range Photogrammetry is a technique for obtaining the geometric information (e.g. position, distance, size and shape) of any object in 3D space that was imaged on the two dimensional (2D) photos, (Wolf, P.R, et.al, 2000) DEM Generation requires many processing and computation, such as camera calibration, stereo matching, editing, and interpolation. All the mentioned steps contribute to the quality of DEM. Image on close range Photogrammetry can be captured using three kind of camera: metric camera, semi-metric camera, and non-metric camera (Hanke, K., et.al, 2002). In this paper DEM quality assessed at Kadavur area, Karur district, Tamil Naudu, India using Close Range Photogrammetry technique, Commercial Digital Camera and Leica Photogrammetry Suite.

  17. Large-area homogeneous periodic surface structures generated on the surface of sputtered boron carbide thin films by femtosecond laser processing

    International Nuclear Information System (INIS)

    Serra, R.; Oliveira, V.; Oliveira, J.C.; Kubart, T.; Vilar, R.; Cavaleiro, A.

    2015-01-01

    circumstances. Processing of the amorphous films at low fluence (72 μJ) results in LIPSS formation only on localized spots on the film surface. LIPSS formation was also observed on the top of the undulations formed after laser processing with 78 μJ of the amorphous film deposited at 800 °C. Finally, large-area homogeneous LIPSS coverage of the boron carbide crystalline films surface was achieved within a large range of laser fluences although holes are also formed at higher laser fluences

  18. Large-area homogeneous periodic surface structures generated on the surface of sputtered boron carbide thin films by femtosecond laser processing

    Energy Technology Data Exchange (ETDEWEB)

    Serra, R., E-mail: ricardo.serra@dem.uc.pt [SEG-CEMUC, Mechanical Engineering Department, University of Coimbra, Rua Luís Reis Santos, 3030-788 Coimbra (Portugal); Oliveira, V. [ICEMS-Instituto de Ciência e Engenharia de Materiais e Superfícies, Avenida Rovisco Pais no 1, 1049-001 Lisbon (Portugal); Instituto Superior de Engenharia de Lisboa, Avenida Conselheiro Emídio Navarro no 1, 1959-007 Lisbon (Portugal); Oliveira, J.C. [SEG-CEMUC, Mechanical Engineering Department, University of Coimbra, Rua Luís Reis Santos, 3030-788 Coimbra (Portugal); Kubart, T. [The Ångström Laboratory, Solid State Electronics, P.O. Box 534, SE-751 21 Uppsala (Sweden); Vilar, R. [Instituto Superior de Engenharia de Lisboa, Avenida Conselheiro Emídio Navarro no 1, 1959-007 Lisbon (Portugal); Instituto Superior Técnico, Avenida Rovisco Pais no 1, 1049-001 Lisbon (Portugal); Cavaleiro, A. [SEG-CEMUC, Mechanical Engineering Department, University of Coimbra, Rua Luís Reis Santos, 3030-788 Coimbra (Portugal)

    2015-03-15

    different circumstances. Processing of the amorphous films at low fluence (72 μJ) results in LIPSS formation only on localized spots on the film surface. LIPSS formation was also observed on the top of the undulations formed after laser processing with 78 μJ of the amorphous film deposited at 800 °C. Finally, large-area homogeneous LIPSS coverage of the boron carbide crystalline films surface was achieved within a large range of laser fluences although holes are also formed at higher laser fluences.

  19. Comparative analysis of surface soil moisture retrieval using VSWI and TVDI in karst areas

    Science.gov (United States)

    Yan, Hongbo; Zhou, Guoqing; Lu, Xianjian

    2015-12-01

    Vegetation Supply Water Index (VSWI) and Temperature Vegetation dryness Index (TVDI) are two most commonly used methods for surface soil moisture (SSM) retrieval using electromagnetic spectrum of visible, near infrared and thermal infrared band. Both of them take into account the effect of vegetation index (VI) and surface temperature (Ts) on SSM. A comparative analysis of the ability and effect of the two methods for SSM retrieval in karst areas was carried out, using the remote sensing data of Landsat 8 OLI_TIRS. The study area is located in Guilin, which is a typical karst area. The experimental results show that TVDI is more suitable for SSM retrieval in karst areas.

  20. Influence of Ecological Factors on Estimation of Impervious Surface Area Using Landsat 8 Imagery

    Directory of Open Access Journals (Sweden)

    Yuqiu Jia

    2017-07-01

    Full Text Available Estimation of impervious surface area is important to the study of urban environments and social development, but surface characteristics, as well as the temporal, spectral, and spatial resolutions of remote sensing images, influence the estimation accuracy. To investigate the effects of regional environmental characteristics on the estimation of impervious surface area, we divided China into seven sub-regions based on climate, soil type, feature complexity, and vegetation phenology: arid and semi-arid areas, Huang-Huai-Hai winter wheat production areas, typical temperate regions, the Pearl River Delta, the middle and lower reaches of the Yangtze River, typical tropical and subtropical regions, and the Qinghai Tibet Plateau. Impervious surface area was estimated from Landsat 8 images of five typical cities, including Yinchuan, Shijiazhuang, Shenyang, Ningbo, and Kunming. Using the linear spectral unmixing method, impervious and permeable surface areas were determined at the pixel-scale based on end-member proportions. We calculated the producer’s accuracy, user’s accuracy, and overall accuracy to assess the estimation accuracy, and compared the accuracies among images acquired from different seasons and locations. In tropical and subtropical regions, vegetation canopies can confound the identification of impervious surfaces and, thus, images acquired in winter, early spring, and autumn are most suitable; estimations in the Pearl River Delta, the middle and lower reaches of the Yangtze River are influenced by soil, vegetation phenology, vegetation canopy, and water, and images acquired in spring, summer, and autumn provide the best results; in typical temperate areas, images acquired from spring to autumn are most effective for estimations; in winter wheat-growing areas, images acquired throughout the year are suitable; and in arid and semi-arid areas, summer and early autumn, during which vegetation is abundant, are the optimal seasons for

  1. Benchmarking sensitivity of biophysical processes to leaf area changes in land surface models

    Science.gov (United States)

    Forzieri, Giovanni; Duveiller, Gregory; Georgievski, Goran; Li, Wei; Robestson, Eddy; Kautz, Markus; Lawrence, Peter; Ciais, Philippe; Pongratz, Julia; Sitch, Stephen; Wiltshire, Andy; Arneth, Almut; Cescatti, Alessandro

    2017-04-01

    , ultimately affecting the amount of absorbed radiation. In addition patterns of simulated turbulent fluxes appear opposite to observations. Such systematic errors shed light on the current partial understanding of some of the mechanisms controlling the surface energy balance. In contrast forests appear reasonably well represented with respect to the interactions between LAI and turbulent fluxes across most climatological gradients, while for net radiation this is only true for warm climates. These proven strengths increase the confidence on how certain processes are simulated in LSMs. The model capacity to mimic the vegetation-biophysics interplay has been tested over the real scenario of greening that occurred in the last 30 years. We found that the modeled trends in surface heat fluxes associated with the long-term changes in leaf area could vary largely from those observed, with different discrepancies across models and climate zones. Our findings help to identify knowledge gaps and improve model representation of the sensitivity of biophysical processes to changes in leaf area density. In particular, comparing models and observations over a wide range of climate and vegetation conditions, as analyzed here, allowed capturing non-linearity of system responses that may emerge more frequently in future climate scenarios.

  2. Thermodynamical and structural properties of solid surfaces in the high temperature range by molecular dynamics solution: evidence for a roughening transition on the F.C.C. {110} surface

    International Nuclear Information System (INIS)

    Rosato, Vittorio

    1986-01-01

    We have studied by Molecular Dynamics simulation the thermodynamical and structural properties of the {110} solid Argon surface as a function of temperature up to T m . The following results have been obtained: 1) the Arrhenius plot indicates that for T> 0.7 T m the defect creation becomes a nearly athermal process. The measured surface diffusion coefficients are very high and are comparable with those observed in the liquid state. 2) the long range order is preserved at least up to T= 0.94 T m . The thermal disorder is related to the onset of a roughening transition on that surface at T ≅ 0.7 T m . Surface layers are not melted in the whole range of temperature we have studied. Furthermore we have investigated the influence of constraints on the surface structure for the same model system previously used at T = 0.48 T m . We have shown that both temperature and constraints induce disorder on surface: for constraints corresponding to elastic deformations of -5 pc applied along the dense axis {110}, the surface structure results to be very similar to that obtained, without constraints, at a higher temperature (T = 0.68 T m ). The implications of our bindings in several areas of Materials Science are briefly discussed. (author) [fr

  3. CLPX-Satellite: EO-1 Hyperion Surface Reflectance, Snow-Covered Area, and Grain Size

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set consists of apparent surface reflectance, subpixel snow-covered area and grain size collected from the Hyperion hyperspectral imager. The Hyperion...

  4. Experimental demonstration of CMOS-compatible long-range dielectric-loaded surface plasmon-polariton waveguides (LR-DLSPPWs)

    DEFF Research Database (Denmark)

    Zektzer, Roy; Desiatov, Boris; Mazurski, Noa

    2015-01-01

    We demonstrate the design, fabrication and experimental characterization of long-range dielectric-loaded surface plasmon-polariton waveguides (LR-DLSPPWs) that are compatible with complementary metal-oxide semiconductor (CMOS) technology. The demonstrated waveguides feature good mode confinement...

  5. Dynamic range of nanoresonators with random rough surfaces in the presence of thermomechanical and momentum exchange noise

    NARCIS (Netherlands)

    Palasantzas, G.

    2007-01-01

    The authors investigate the simultaneous influence of thermomechanical and momentum exchange noise on the linear dynamic range DR of nanoresonators with random rough surfaces. The latter are characterized by the roughness amplitude w, the lateral correlation length xi, and the roughness exponent 0

  6. Representation of Glossy Material Surface in Ventral Superior Temporal Sulcal Area of Common Marmosets.

    Science.gov (United States)

    Miyakawa, Naohisa; Banno, Taku; Abe, Hiroshi; Tani, Toshiki; Suzuki, Wataru; Ichinohe, Noritaka

    2017-01-01

    The common marmoset ( Callithrix jacchus ) is one of the smallest species of primates, with high visual recognition abilities that allow them to judge the identity and quality of food and objects in their environment. To address the cortical processing of visual information related to material surface features in marmosets, we presented a set of stimuli that have identical three-dimensional shapes (bone, torus or amorphous) but different material appearances (ceramic, glass, fur, leather, metal, stone, wood, or matte) to anesthetized marmoset, and recorded multiunit activities from an area ventral to the superior temporal sulcus (STS) using multi-shanked, and depth resolved multi-electrode array. Out of 143 visually responsive multiunits recorded from four animals, 29% had significant main effect only of the material, 3% only of the shape and 43% of both the material and the shape. Furthermore, we found neuronal cluster(s), in which most cells: (1) showed a significant main effect in material appearance; (2) the best stimulus was a glossy material (glass or metal); and (3) had reduced response to the pixel-shuffled version of the glossy material images. The location of the gloss-selective area was in agreement with previous macaque studies, showing activation in the ventral bank of STS. Our results suggest that perception of gloss is an important ability preserved across wide range of primate species.

  7. Influence of CuO catalyst in the nanoscale range on SnO2 surface ...

    Indian Academy of Sciences (India)

    The dispersal of CuO catalyst on the surface of the semiconducting SnO2 film is found to be of vital importance for improving the sensitivity and the response speed of a SnO2 gas sensor for H2S gas detection. Ultra-thin CuO islands (8 nm thin and 0.6 mm diameter) prepared by evaporating Cu through a mesh and ...

  8. Influence of CuO catalyst in the nanoscale range on SnO2 surface ...

    Indian Academy of Sciences (India)

    Abstract. The dispersal of CuO catalyst on the surface of the semiconducting SnO2 film is found to be of vital importance for improving the sensitivity and the response speed of a SnO2 gas sensor for H2S gas detection. Ultra-thin CuO islands (8 nm thin and. 0.6 mm diameter) prepared by evaporating Cu through a mesh and ...

  9. Interdependence between body surface area and ultraviolet B dose in vitamin D production

    DEFF Research Database (Denmark)

    Bogh, M K B; Schmedes, Anne; Philipsen, P A

    2011-01-01

    Ultraviolet (UV) B radiation increases serum vitamin D level expressed as 25-hydroxyvitamin-D(3) [25(OH)D], but the relationship to body surface area and UVB dose needs investigation.......Ultraviolet (UV) B radiation increases serum vitamin D level expressed as 25-hydroxyvitamin-D(3) [25(OH)D], but the relationship to body surface area and UVB dose needs investigation....

  10. Estimation of surface area concentration of workplace incidental nanoparticles based on number and mass concentrations

    Science.gov (United States)

    Park, J. Y.; Ramachandran, G.; Raynor, P. C.; Kim, S. W.

    2011-10-01

    Surface area was estimated by three different methods using number and/or mass concentrations obtained from either two or three instruments that are commonly used in the field. The estimated surface area concentrations were compared with reference surface area concentrations (SAREF) calculated from the particle size distributions obtained from a scanning mobility particle sizer and an optical particle counter (OPC). The first estimation method (SAPSD) used particle size distribution measured by a condensation particle counter (CPC) and an OPC. The second method (SAINV1) used an inversion routine based on PM1.0, PM2.5, and number concentrations to reconstruct assumed lognormal size distributions by minimizing the difference between measurements and calculated values. The third method (SAINV2) utilized a simpler inversion method that used PM1.0 and number concentrations to construct a lognormal size distribution with an assumed value of geometric standard deviation. All estimated surface area concentrations were calculated from the reconstructed size distributions. These methods were evaluated using particle measurements obtained in a restaurant, an aluminum die-casting factory, and a diesel engine laboratory. SAPSD was 0.7-1.8 times higher and SAINV1 and SAINV2 were 2.2-8 times higher than SAREF in the restaurant and diesel engine laboratory. In the die casting facility, all estimated surface area concentrations were lower than SAREF. However, the estimated surface area concentration using all three methods had qualitatively similar exposure trends and rankings to those using SAREF within a workplace. This study suggests that surface area concentration estimation based on particle size distribution (SAPSD) is a more accurate and convenient method to estimate surface area concentrations than estimation methods using inversion routines and may be feasible to use for classifying exposure groups and identifying exposure trends.

  11. Estimation of surface area concentration of workplace incidental nanoparticles based on number and mass concentrations

    International Nuclear Information System (INIS)

    Park, J. Y.; Ramachandran, G.; Raynor, P. C.; Kim, S. W.

    2011-01-01

    Surface area was estimated by three different methods using number and/or mass concentrations obtained from either two or three instruments that are commonly used in the field. The estimated surface area concentrations were compared with reference surface area concentrations (SA REF ) calculated from the particle size distributions obtained from a scanning mobility particle sizer and an optical particle counter (OPC). The first estimation method (SA PSD ) used particle size distribution measured by a condensation particle counter (CPC) and an OPC. The second method (SA INV1 ) used an inversion routine based on PM1.0, PM2.5, and number concentrations to reconstruct assumed lognormal size distributions by minimizing the difference between measurements and calculated values. The third method (SA INV2 ) utilized a simpler inversion method that used PM1.0 and number concentrations to construct a lognormal size distribution with an assumed value of geometric standard deviation. All estimated surface area concentrations were calculated from the reconstructed size distributions. These methods were evaluated using particle measurements obtained in a restaurant, an aluminum die-casting factory, and a diesel engine laboratory. SA PSD was 0.7–1.8 times higher and SA INV1 and SA INV2 were 2.2–8 times higher than SA REF in the restaurant and diesel engine laboratory. In the die casting facility, all estimated surface area concentrations were lower than SA REF . However, the estimated surface area concentration using all three methods had qualitatively similar exposure trends and rankings to those using SA REF within a workplace. This study suggests that surface area concentration estimation based on particle size distribution (SA PSD ) is a more accurate and convenient method to estimate surface area concentrations than estimation methods using inversion routines and may be feasible to use for classifying exposure groups and identifying exposure trends.

  12. Changes in the intestinal microvillous surface area during reproduction and ageing in the female rat.

    OpenAIRE

    Pénzes, L; Regius, O

    1985-01-01

    A morphometric study has been undertaken of the changes that occur in the microvillous surface area of young, pregnant, lactating, old and senescent rats. It has been shown that the microvilli are organelles with a quite stable conformation and that they exhibit no large scale dimensional changes throughout almost the entire life span. Lactation, however, does induce an apparent increase in microvillous surface area which may be associated with the significant changes which occur to the struc...

  13. Relationship between specific surface area and spatial correlation functions for anisotropic porous media

    Energy Technology Data Exchange (ETDEWEB)

    Berryman, J.G.

    1987-01-01

    A result of Debye, Anderson, and Brumberger (P. Debye, H. R. Anderson, Jr., and H. Brumberger, J. Appl. Phys. 28, 679 (1957)) for isotropic porous media states that the derivative of the two-point spatial correlation at the origin is equal to minus one-quarter of the specific surface area. This result is generalized for nonisotropic media by noting that the angular average of the anisotropic two-point spatial correlation function has the same relationship to the specific surface area.

  14. On the diurnal ranges of Sea Surface Temperature (SST) in the ...

    Indian Academy of Sciences (India)

    A simple regression model based on the peak solar radiation and average wind speed was good enough to estimate the diurnal range of SST at ∼1.0 m in the north Indian Ocean during most of the seasons except under low wind-high solar radiation conditions that occur mostly during spring. The additional information on ...

  15. Lake Chad Total Surface Water Area as Derived from Land Surface Temperature and Radar Remote Sensing Data

    Directory of Open Access Journals (Sweden)

    Frederick Policelli

    2018-02-01

    Full Text Available Lake Chad, located in the middle of the African Sahel belt, underwent dramatic decreases in the 1970s and 1980s leaving less than ten percent of its 1960s surface water extent as open water. In this paper, we present an extended record (dry seasons 1988–2016 of the total surface water area of the lake (including both open water and flooded vegetation derived using Land Surface Temperature (LST data (dry seasons 2000–2016 from the NASA Terra MODIS sensor and EUMETSAT Meteosat-based LST measurements (dry seasons 1988–2001 from an earlier study. We also examine the total surface water area for Lake Chad using radar data (dry seasons 2015–2016 from the ESA Sentinel-1a mission. For the limited number of radar data sets available to us (18 data sets, we find on average a close match between the estimates from these data and the corresponding estimates from LST, though we find spatial differences in the estimates using the two types of data. We use these spatial differences to adjust the record (dry seasons 2000–2016 from MODIS LST. Then we use the adjusted record to remove the bias of the existing LST record (dry seasons 1988–2001 derived from Meteosat measurements and combine the two records. From this composite, extended record, we plot the total surface water area of the lake for the dry seasons of 1988–1989 through 2016–2017. We find for the dry seasons of 1988–1989 to 2016–2017 that the maximum total surface water area of the lake was approximately 16,800 sq. km (February and May, 2000, the minimum total surface water area of the lake was approximately 6400 sq. km (November, 1990, and the average was approximately 12,700 sq. km. Further, we find the total surface water area of the lake to be highly variable during this period, with an average rate of increase of approximately 143 km2 per year.

  16. Geohydrology and susceptibility of major aquifers to surface contamination in Alabama, area 7

    Science.gov (United States)

    Mooty, W.S.

    1987-01-01

    The geohydrology and susceptibility of the seven major aquifers to surface contamination in Area 7 - Bibb, Dallas, Hale, Perry, and Wilcox Counties, are described. Aquifers in the northern part of the study area are in Paleozoic limestones and dolomite formations. Deposits in the central part of the study area are predominately of Cretaceous age and contain the Coker, Gordo, and Eutaw aquifers. Although the southern part of the study area has many deposits of Tertiary age, the Ripley Formation of Cretaceous age is the major aquifer. Contamination of any of the major aquifers is improbable because the majority of the recharge area for the primary aquifers is woodland, pasture, or farmland. Downdip from their outcrops, the major aquifers in the study area are protected from land surface contamination by relatively impermeable layers of clay and chalk. The aquifers that are highly susceptible to contamination are the ones in the limestone and dolomite formations in northern Bibb County. Sinkholes exist in the recharge area of these formations and could provide a direct link for contaminates from the land surface to the water table. An area northeast of the Selma well field is also highly susceptible to contamination. The Eutaw Formation in this area is overlain by alluvial deposits that could increase recharge to the aquifer by slowing the runoff rate of surface water. (USGS)

  17. Changes in Thickness and Surface Area of the Human Cortex and Their Relationship with Intelligence

    NARCIS (Netherlands)

    Schnack, Hugo G.; Van Haren, Neeltje E M; Brouwer, Rachel M.; Evans, Alan; Durston, Sarah; Boomsma, Dorret I.; Kahn, René S.; Hulshoff Pol, Hilleke E.

    2015-01-01

    Changes in cortical thickness over time have been related to intelligence, but whether changes in cortical surface area are related to general cognitive functioning is unknown. We therefore examined the relationship between intelligence quotient (IQ) and changes in cortical thickness and surface

  18. Greenland surface mass-balance observations from the ice-sheet ablation area and local glaciers

    DEFF Research Database (Denmark)

    Machguth, Horst; Thomsen, Henrik H.; Weidick, Anker

    2016-01-01

    Glacier surface mass-balance measurements on Greenland started more than a century ago, but no compilation exists of the observations from the ablation area of the ice sheet and local glaciers. Such data could be used in the evaluation of modelled surface mass balance, or to document changes in g...

  19. Greenland surface mass-balance observations from the ice-sheet ablation area and local glaciers

    NARCIS (Netherlands)

    Machguth, Horst; Thomsen, Henrik H.; Weidick, Anker; Ahlstrøm, Andreas P.; Abermann, Jakob; Andersen, Morten L.; Andersen, Signe B.; Bjørk, Anders A.; Box, Jason E.; Braithwaite, Roger J.; Bøggild, Carl E.; Citterio, Michele; Clement, Poul; Colgan, William; Fausto, Robert S.; Gleie, Karin; Gubler, Stefanie; Hasholt, Bent; Hynek, Bernhard; Knudsen, Niels T.; Larsen, Signe H.; Mernild, Sebastian H.; Oerlemans, Johannes; Oerter, Hans; Olesen, Ole B.; Smeets, C. J P Paul; Steffen, Konrad; Stober, Manfred; Sugiyama, Shin; Van As, Dirk; Van Den Broeke, Michiel R.; Van De Wal, Roderik S W

    2016-01-01

    Glacier surface mass-balance measurements on Greenland started more than a century ago, but no compilation exists of the observations from the ablation area of the ice sheet and local glaciers. Such data could be used in the evaluation of modelled surface mass balance, or to document changes in

  20. Short-range surface plasmonics: Localized electron emission dynamics from a 60-nm spot on an atomically flat single-crystalline gold surface.

    Science.gov (United States)

    Frank, Bettina; Kahl, Philip; Podbiel, Daniel; Spektor, Grisha; Orenstein, Meir; Fu, Liwei; Weiss, Thomas; Horn-von Hoegen, Michael; Davis, Timothy J; Meyer Zu Heringdorf, Frank-J; Giessen, Harald

    2017-07-01

    We experimentally and theoretically visualize the propagation of short-range surface plasmon polaritons using atomically flat single-crystalline gold platelets on silicon substrates. We study their excitation and subfemtosecond dynamics via normal-incidence two-photon photoemission electron microscopy. By milling a plasmonic disk and grating structure into a single-crystalline gold platelet, we observe nanofocusing of the short-range surface plasmon polariton. Localized two-photon ultrafast electron emission from a spot with a smallest dimension of 60 nm is observed. Our novel approach opens the door toward reproducible plasmonic nanofocusing devices, which do not degrade upon high light intensity or heating due to the atomically flat surface without any tips, protrusions, or holes. Our nanofoci could also be used as local emitters for ultrafast electron bunches in time-resolved electron microscopes.

  1. Models of bedrock surface and overburden thickness over Olkiluoto island and nearby sea area

    Energy Technology Data Exchange (ETDEWEB)

    Moenkkoenen, H. [WSP Finland Oy, Helsinki (Finland)

    2012-04-15

    In this report, a model of bedrock surface and a model of overburden thickness over the Olkiluoto Island and the nearby sea area are presented. Also in purpose to produce material for biosphere and radionuclide transport modelling, stratigraphy models of different sediment layers were created at two priority areas north and south of the Olkiluoto Island. The work concentrated on the collection and description of available data of bedrock surface and overburden thickness. Because the information on the bedrock surface and overburden is collected from different sources and is based on a number of types of data the quality and applicability of data sets varies. Consequently also the reliability in different parts of the models varies. Input data for the bedrock surface and overburden thickness models include 2928 single points and additional outcrops observations (611 polygons) in the modelled area. In addition, the input data include 173 seismic refraction lines (6534 points) and acousticseismic sounding lines (26655 points from which 13721 points are located in model area) in the Olkiluoto offshore area. The average elevation of bedrock surface in area is 2.1 metres above the sea level. The average thickness of overburden is 2.5 metres varying typically between 2 - 4 metres. Thickest overburden covers (approximately 16 metres) of terrestrial area are located at the western end of the Olkiluoto Island and in sea basin south of the island. (orig.)

  2. One-level modeling for diagnosing surface winds over complex terrain. II - Applicability to short-range forecasting

    Science.gov (United States)

    Alpert, P.; Getenio, B.; Zak-Rosenthal, R.

    1988-01-01

    The Alpert and Getenio (1988) modification of the Mass and Dempsey (1985) one-level sigma-surface model was used to study four synoptic events that included two winter cases (a Cyprus low and a Siberian high) and two summer cases. Results of statistical verification showed that the model is not only capable of diagnosing many details of surface mesoscale flow, but might also be useful for various applications which require operative short-range prediction of the diurnal changes of high-resolution surface flow over complex terrain, for example, in locating wildland fires, determining the dispersion of air pollutants, and predicting changes in wind energy or of surface wind for low-level air flights.

  3. Water and Carbon Dioxide Ices-Rich Areas on Comet 67P/CG Nucleus Surface

    Science.gov (United States)

    Filacchione, G.; Capaccioni, F.; Raponi, A.; De Sanctis, M. C.; Ciarniello, M.; Barucci, M. A.; Tosi, F.; Migliorini, A.; Capria, M. T.; Erard, S.; Bockelée-Morvan, D.; Leyrat, C.; Arnold, G.; Kappel, D.; McCord, T. B.

    2017-01-01

    So far, only two ice species have been identified by Rosetta/VIRTIS-M [1] on the surface of 67P/Churyumov-Gerasimenko during the pre-perihelion time: crystalline water and carbon dioxide ice. Water ice has been spectroscopically identified in three distinct modalities: 1) On the active areas of Hapi region where water ice changes its abundance with local time and illumination conditions, condensing during the night hours and sublimating during daytime [2]; 2) On recent debris fields collapsed from two elevated structures in the Imhotep region where more fresh and pristine material is exposed [3]; 3) On eight bright areas located in Khonsu, Imhotep, Anhur, Atum and Khepry regions [4] where single or multiple grouped icy patches with sizes ranging between few meters to about 60 m are observed. Carbon dioxide ice has been detected only in a 60-80 m area in Anhur region while it was exiting from a four year-long winter-night season [5]. This ice deposit underwent a rapid sublimation, disappearing in about one month after its initial detection. While water and carbon dioxide ice appear always mixed with the ubiquitous dark material [6,7], there are no evidences of the presence of water and carbon dioxide ices mixed together in the same area. If observed, ices always account for very small fraction (few percent) with respect to the dark material. Moreover, the surface ice deposits are preferentially located on the large lobe and the neck while they are absent on the small lobe. Apart from these differences in the spatial distribution of ices on the surface, a large variability is observed the mixing modalities and in the grain size distributions, as retrieved from spectral modeling [8]: 1) very small μm-sized water ice grains in intimate mixing with the dark terrain are detected on Hapi active regions [2]; 2) two monodispersed distributions with maxima at 56 μm and at 2 mm, corresponding to the intimate and areal mixing classes, are observedon the Imhotep debris

  4. Estimation of cerebral surface area using vertical sectioning and magnetic resonance imaging: a stereological study.

    Science.gov (United States)

    Acer, Niyazi; Cankaya, Mehmet Niyazi; Işçi, Oznur; Baş, Orhan; Camurdanoğlu, Mehmet; Turgut, Mehmet

    2010-01-15

    Stereological techniques using isotropic uniform random and vertical uniform random sections have been used for surface area estimation. However, there are a few studies in which the surface area of the brain is estimated using the vertical section technique in a stereological approach. The objective of the current study was to apply the vertical section technique using cycloid test probes for estimation of cerebral surface area in magnetic resonance imaging (MRI). In this study, cerebral surface areas were estimated in a total of 13 young subjects (6 males, 7 females) who were free of any neurological symptoms and signs. The means (+/-S.D.) of the surface areas were 1619.92+/-140. 97 cm (2), 1625.69+/-147. 58 cm(2) and 1674.69+/-160. 60 cm(2) for 36, 18 and 12 vertical sections, respectively. The mean coefficient of error obtained by applying cycloid test lines that use a 2. 8-cm ratio of area associated with each cycloid was estimated at 0.05). In addition, the three models correlated well with each other. From these results, it is concluded that the vertical section technique is an unbiased, efficient and reliable method and is ideally suited to in vivo examination of MRI data for estimating the surface area of the brain. Hence, we suggest that estimation of surface area using MRI and stereology may be clinically relevant for assessing cortical atrophy as well as for investigating the structure and function of cerebral hemispheres. Copyright 2009 Elsevier B.V. All rights reserved.

  5. Controlling the Short-Range Propagation Environment Using Active Frequency Selective Surfaces

    Directory of Open Access Journals (Sweden)

    L. Subrt

    2010-12-01

    Full Text Available This paper deals with a new approach to the control of the propagation environment in indoor scenarios using intelligent walls. The intelligent wall is a conventional wall situated inside a building, but equipped with an active frequency selective surface and sensors. The intelligent wall can be designed as a self-configuring and self-optimizing autonomous part of a collaborative infrastructure working within a high-capacity mobile radio system. The paper shows how such surfaces can be used to adjust the electromagnetic characteristics of the wall in response to changes in traffic demand, monitored using a network of sensors, thereby controlling the propagation environment inside the building. Some of the potential problems (mainly controlling coverage and interference relating to an increased usage of wireless systems both inside and outside buildings are discussed and possible solutions using intelligent walls with the active FSS are suggested. The positive influence of intelligent walls on system performance is shown and results obtained from the simulations are shown and discussed.

  6. HIGH-RESOLUTION SURFACE RECONSTRUCTION FROM IMAGERY FOR CLOSE RANGE CULTURAL HERITAGE APPLICATIONS

    Directory of Open Access Journals (Sweden)

    K. Wenzel

    2012-07-01

    Full Text Available The recording of high resolution point clouds with sub-mm resolution is a demanding and cost intensive task, especially with current equipment like handheld laser scanners. We present an image based approached, where techniques of image matching and dense surface reconstruction are combined with a compact and affordable rig of off-the-shelf industry cameras. Such cameras provide high spatial resolution with low radiometric noise, which enables a one-shot solution and thus an efficient data acquisition while satisfying high accuracy requirements. However, the largest drawback of image based solutions is often the acquisition of surfaces with low texture where the image matching process might fail. Thus, an additional structured light projector is employed, represented here by the pseudo-random pattern projector of the Microsoft Kinect. Its strong infrared-laser projects speckles of different sizes. By using dense image matching techniques on the acquired images, a 3D point can be derived for almost each pixel. The use of multiple cameras enables the acquisition of a high resolution point cloud with high accuracy for each shot. For the proposed system up to 3.5 Mio. 3D points with sub-mm accuracy can be derived per shot. The registration of multiple shots is performed by Structure and Motion reconstruction techniques, where feature points are used to derive the camera positions and rotations automatically without initial information.

  7. Graphene Oxide Derived Carbons (GODC); High-Surface Area NanoPorous Materials for Hydrogen Storage and Carbon Capture

    Science.gov (United States)

    Yildirim, Taner

    2012-02-01

    Even though there has been extensive research on gas adsorption properties of various carbon materials based on activated carbon and nanotubes, there has been little work done on the gas adsorption properties of graphite oxide (GO). In this study [1], we show that one-and-a-half-century-old graphite oxide can be easily turned into a potentially useful gas storage material. In order to create high-surface nanoporous materials from GO, we used two different approaches. In the first approach, we have successfully synthesized graphene-oxide framework materials (GOFs) by interlinking GO layers by diboronic acids. The resulting GOF materials have well defined pore size and BET surface area up to 500 m2/g with twice larger heat of adsorption of H2 and CO2 than those found in other physisorption materials such as MOF5. In the second approach, we synthesized a range of high surface area GO derived carbons (GODC) and studied their applications toward H2, CO2 and CH4 gas storage. The GODCs, with wide range of pore structure, have been prepared by chemical activation with potassium hydroxide (KOH). We obtain largely increased surface areas up to nearly 1900 m^2/g for GODC samples from 10 m^2/g for initial GO. A detailed experimental study of high pressure excess sorption isotherms on GODCs reveal an increase in both CO2 and CH4 storage capacities compared to other high surface area activated carbons. Finally, we compared the gas sorption properties of our GO-based matarials with other systems such as MOFs, ZIFs, and COFs. [4pt] [1] See http://www.ncnr.nist.gov/staff/taner for references and more information.

  8. Application of stereological methods to estimate post-mortem brain surface area using 3T MRI

    DEFF Research Database (Denmark)

    Furlong, Carolyn; García-Fiñana, Marta; Puddephat, Michael

    2013-01-01

    The Cavalieri and Vertical Sections methods of design based stereology were applied in combination with 3 tesla (i.e. 3T) Magnetic Resonance Imaging (MRI) to estimate cortical and subcortical volume, area of the pial surface, area of the grey-white matter boundary, and thickness of the cerebral c...

  9. Vaccination of dogs with Trypanosoma rangeli induces antibodies against Trypanosoma cruzi in a rural area of Córdoba, Argentina.

    Science.gov (United States)

    Basso, Beatriz; Marini, Vanina; Gauna, Diego; Frias, Maria

    2016-04-01

    Dogs play a major role in the domestic cycle of Trypanosoma cruzi, acting as reservoirs. In a previous work we have developed a model of vaccination of dogs in captivity with nonpathogenic Trypanosoma rangeli epimastigotes, resulting in the production of protective antibodies against T. cruzi, with dramatic decrease of parasitaemia upon challenge with 100,000 virulent forms of this parasite. The aim of this work was to evaluate the immunogenicity of this vaccine in dogs living in a rural area. Domestic dogs, free from T. cruzi infection, received three immunisations with fixed T. rangeli epimastigotes. Dogs were not challenged with T. cruzi, but they were left in their environment. This immunisation induced antibodies against T. cruzi for more than three years in dogs in their natural habitat, while control dogs remained serologically negative.

  10. Investigation of Range Profiles from a Simplified Ship on Rough Sea Surface and Its Multipath Imaging Mechanisms

    Directory of Open Access Journals (Sweden)

    Siyuan He

    2012-01-01

    Full Text Available The range profiles of a two-dimension (2 D perfect electric conductor (PEC ship on a wind-driven rough sea surface are derived by performing an inverse discrete Fourier transform (IDFT on the wide band backscattered field. The rough sea surface is assuming to be a PEC surface. The back scattered field is computed based on EM numerical simulation when the frequencies are sampled between 100 MHz and 700 MHz. Considering the strong coupling interactions between the ship and sea, the complicated multipath effect to the range profile characteristics is fully analyzed based on the multipath imaging mechanisms. The coupling mechanisms could be explained by means of ray theory prediction and numerical extraction of the coupling currents. The comparison of the range profile locations between ray theory prediction and surface current simulation is implemented and analyzed in this paper. Finally, the influence of different sea states on the radar target signatures has been examined and discussed.

  11. Corrective Action Decision Document for Corrective Action Unit 486: Double Tracks RADSAFE Area, Nellis Air Force Range, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    ITLV

    1999-07-12

    This Corrective Action Decision Document (CADD) has been prepared for Corrective Action Unit (CAU) 486, Double Tracks Radiological Safety (RADSAFE) Area (DTRSA) in accordance with the Federal Facility Agreement and Consent Order (FFACO) of 1996 that was agreed to by the U.S. Department of Energy, Nevada Operations Office (DOE/NV); the Nevada Division of Environmental Protection (NDEP); and the U.S Department of Defense (FFACO, 1996). The CADD provides or references the specific information necessary to recommend a preferred corrective action for the single Corrective Action Site (CAS), 71-23-001-71DT, within CAU 486. Corrective Action Unit 486 is located on the Nellis Air Force Range 71 North, west of the Tonopah Test Range (TTR), Nevada. The TTR, located in the Nellis Air Force Range, is approximately 140 miles (mi) northwest of Las Vegas, Nevada (Figure 1-1). The DTRSA is located on the west side of the Cactus Range approximately 5 mi southwest of the Cactus Spring gate at the intersection of the Cactus Spring Road and the Double Tracks Control Point Road (Figure 1-2).

  12. Risks of avian influenza transmission in areas of intensive free-ranging duck production with wild waterfowl

    Science.gov (United States)

    Cappelle, Julien; Zhao, Delong; Gilbert, Marius; Newman, Scott H.; Takekawa, John Y.; Gaidet, Nicolas; Prosser, Diann J.; Liu, Ying; Li, Peng; Shu, Yuelong; Xiao, Xiangming

    2014-01-01

    For decades, southern China has been considered to be an important source for emerging influenza viruses since key hosts live together in high densities in areas with intensive agriculture. However, the underlying conditions of emergence and spread of avian influenza viruses (AIV) have not been studied in detail, particularly the complex spatiotemporal interplay of viral transmission between wild and domestic ducks, two major actors of AIV epidemiology. In this synthesis, we examine the risks of avian influenza spread in Poyang Lake, an area of intensive free-ranging duck production and large numbers of wild waterfowl. Our synthesis shows that farming of free-grazing domestic ducks is intensive in this area and synchronized with wild duck migration. The presence of juvenile domestic ducks in harvested paddy fields prior to the arrival and departure of migrant ducks in the same fields may amplify the risk of AIV circulation and facilitate the transmission between wild and domestic populations. We provide evidence associating wild ducks migration with the spread of H5N1 in the spring of 2008 from southern China to South Korea, Russia, and Japan, supported by documented wild duck movements and phylogenetic analyses of highly pathogenic avian influenza H5N1 sequences. We suggest that prevention measures based on a modification of agricultural practices may be implemented in these areas to reduce the intensity of AIV transmission between wild and domestic ducks. This would require involving all local stakeholders to discuss feasible and acceptable solutions.

  13. Bardenas Reales Range, Spain. Revised Uniform Summary of Surface Weather Observations (Russwo). Parts A-F.

    Science.gov (United States)

    1975-06-30

    VAIIIL .3. _____ i TOTAL NUMBER OF OBSERVATIONS 141, USAFETAC Ft6 0-8-5 ( EL A) IP0Mvous SO)T)OOS OF THI OIl S 0* 8oLMT0 -f--. .. ’ . ___ SURFACE...88 4 8 88 8 88a8 A 6 ; 8.4 89.2 ;39.5 b9. 5 9 9.8: 89.9; A9.9, 90. 1 90. 9,.l 90.1 90.11) 0. el 90.3 91.2! 92.0 cI2.3* -9 2 7zj 92.81 92.8 93.0 93: q...00.0 TOTAL NUMBER OF OBSERVATIONS - 147 USAF )TAC ’ 0-4-5 L A , , ’) f.I 0 0 tn-t.c DATA P’ CESSIJC tifO -CH V RU /,DIT USAF ETAC CEILING VES S IIBLT AI

  14. Nitrogen diffusion in near-surface range of ion doped molybdenum

    CERN Document Server

    Zamalin, E Y

    2001-01-01

    The dynamics of change in nitrogen near-the-surface concentration in the Mo ion-alloyed monocrystalline foil is studied through the Auger-electron spectroscopy and the secondary ion mass spectrometry. The implantation dose constituted 5 x 10 sup 1 sup 7 ion/cm sup 2 and the implantation energy equaled 50 and 100 keV. The samples diffusion annealing was performed at the temperature of 800-900 deg C. The evaluation of the nitrogen diffusion coefficient indicates the values by 3-5 orders lesser than the diffusion coefficient in the nitrogen solid-state solution in the molybdenum. At the same time the molybdenum self-diffusion coefficient value is by 3-5 orders lesser as compared to the obtained value. The supposition is made, the the surplus nitrogen relative to the solubility limit is deposited on the radiation defects and in the process of the diffusion annealing it nitrates together with them

  15. Large Differences between Glaciers 3D Surface Extents and 2D Planar Areas in Central Tianshan

    Directory of Open Access Journals (Sweden)

    Xianwei Wang

    2017-04-01

    Full Text Available Most glaciers in China lie in high mountainous environments and have relatively large surface slopes. Common analyses consider glaciers’ projected areas (2D Area in a two-dimensional plane, which are much smaller than glacier’s topographic surface extents (3D Area. The areal difference between 2D planar areas and 3D surface extents exceeds −5% when the glacier’s surface slope is larger than 18°. In this study, we establish a 3D model in the Muzart Glacier catchment using ASTER GDEM data. This model is used to quantify the areal difference between glaciers’ 2D planar areas and their 3D surface extents in various slope zones and elevation bands by using the second Chinese Glacier Inventory (CGI2. Finally, we analyze the 2D and 3D area shrinking rate between 2007 and 2013 in Central Tianshan using glaciers derived from Landsat images by an object-based classification approach. This approach shows an accuracy of 89% when it validates by comparison of glaciers derived from Landsat and high spatial resolution GeoEye images. The extracted glaciers in 2007 also have an agreement of 89% with CGI2 data in the Muzart Glacier catchment. The glaciers’ 3D area is 34.2% larger than their 2D area from CGI2 in the Muzart Glacier catchment and by 27.9% in the entire Central Tianshan. Most underestimation occurs in the elevation bands of 4000–5000 m above sea level (a.s.l.. The 3D glacier areas reduced by 30 and 115 km2 between 2007 and 2013 in the Muzart Glacier catchment and Central Tianshan, being 37.0% and 27.6% larger than their 2D areas reduction, respectively. The shrinking rates decrease with elevation increase.

  16. Greenland surface mass-balance observations from the ice-sheet ablation area and local glaciers

    DEFF Research Database (Denmark)

    Machguth, Horst; Thomsen, Henrik H.; Weidick, Anker

    2016-01-01

    Glacier surface mass-balance measurements on Greenland started more than a century ago, but no compilation exists of the observations from the ablation area of the ice sheet and local glaciers. Such data could be used in the evaluation of modelled surface mass balance, or to document changes...... in glacier melt independently from model output. Here, we present a comprehensive database of Greenland glacier surface mass-balance observations from the ablation area of the ice sheet and local glaciers. The database spans the 123 a from 1892 to 2015, contains a total of similar to 3000 measurements from......-term time series of which there are only two exceeding 20 a. We use the data to analyse uncertainties in point measurements of surface mass balance, as well as to estimate surface mass-balance profiles for most regions of Greenland....

  17. Planar spatial correlations, anisotropy, and specific surface area of stationary random porous media

    International Nuclear Information System (INIS)

    Berryman, J.G.

    1998-01-01

    An earlier result of the author showed that an anisotropic spatial correlation function of a random porous medium could be used to compute the specific surface area when it is stationary as well as anisotropic by first performing a three-dimensional radial average and then taking the first derivative with respect to lag at the origin. This result generalized the earlier result for isotropic porous media of Debye et al. [J. Appl. Phys. 28, 679 (1957)]. The present article provides more detailed information about the use of spatial correlation functions for anisotropic porous media and in particular shows that, for stationary anisotropic media, the specific surface area can be related to the derivative of the two-dimensional radial average of the correlation function measured from cross sections taken through the anisotropic medium. The main concept is first illustrated using a simple pedagogical example for an anisotropic distribution of spherical voids. Then, a general derivation of formulas relating the derivative of the planar correlation functions to surface integrals is presented. When the surface normal is uniformly distributed (as is the case for any distribution of spherical voids), our formulas can be used to relate a specific surface area to easily measurable quantities from any single cross section. When the surface normal is not distributed uniformly (as would be the case for an oriented distribution of ellipsoidal voids), our results show how to obtain valid estimates of specific surface area by averaging measurements on three orthogonal cross sections. One important general observation for porous media is that the surface area from nearly flat cracks may be underestimated from measurements on orthogonal cross sections if any of the cross sections happen to lie in the plane of the cracks. This result is illustrated by taking the very small aspect ratio (penny-shaped crack) limit of an oblate spheroid, but holds for other types of flat surfaces as well

  18. Pore scale heterogeneity in the mineral distribution and surface area of porous rocks

    Science.gov (United States)

    Lai, Peter; Moulton, Kevin; Krevor, Samuel

    2014-05-01

    There are long-standing challenges in characterizing reactive transport in porous media at scales larger than individual pores. This hampers the prediction of the field-scale impact of geochemical processes on fluid flow [1]. This is a source of uncertainty for carbon dioxide injection, which results in a reactive fluid-rock system, particularly in carbonate rock reservoirs. A potential cause is the inability of the continuum approach to incorporate the impact of heterogeneity in pore-scale reaction rates. This results in part from pore-scale heterogeneities in surface area of reactive minerals [2,3]. The objective of this study was to quantify heterogeneity in reactive surface and observe the extent of its non-normal character. In this study we describe our work in using micron-scale x-ray imaging and other spectroscopic techniques for the purpose of describing the statistical distribution of reactive surface area within a porous medium, and identifying specific mineral phases and their distribution in 3-dimensions. Using in-house image processing techniques and auxilary charactersation with thin section, electron microscope and spectroscopic techniques we quantified the surface area of each mineral phase in the x-ray CT images. This quantification was validated against nitrogen BET surface area and backscattered electron imaging measurements of the CT-imaged samples. Distributions in reactive surface area for each mineral phase were constructed by calculating surface areas in thousands of randomly selected subvolume images of the total sample, each normalized to the pore volume in that image. In all samples, there is little correlation between the reactive surface area fraction and the volumetric fraction of a mineral in a bulk rock. Berea sandstone was far less heterogeneous and has a characteristic pore size at which a surface area distribution may be used to quantify heterogeneity. In carbonates, heterogeneity is more complex and surface area must be

  19. Technology of surface wastewater purification, including high-rise construction areas

    Science.gov (United States)

    Tsyba, Anna; Skolubovich, Yury

    2018-03-01

    Despite on the improvements in the quality of high-rise construction areas and industrial wastewater treatment, the pollution of water bodies continues to increase. This is due to the organized and unorganized surface untreated sewage entry into the reservoirs. The qualitative analysis of some cities' surface sewage composition is carried out in the work. Based on the published literature review, the characteristic contamination present in surface wastewater was identified. The paper proposes a new technology for the treatment of surface sewage and presents the results of preliminary studies.

  20. Estimating surface fluxes over the north Tibetan Plateau area with ASTER imagery

    Directory of Open Access Journals (Sweden)

    Weiqiang Ma

    2009-01-01

    Full Text Available Surface fluxes are important boundary conditions for climatological modeling and Asian monsoon system. The recent availability of high-resolution, multi-band imagery from the ASTER (Advanced Space-borne Thermal Emission and Reflection radiometer sensor has enabled us to estimate surface fluxes to bridge the gap between local scale flux measurements using micrometeorological instruments and regional scale land-atmosphere exchanges of water and heat fluxes that are fundamental for the understanding of the water cycle in the Asian monsoon system. A parameterization method based on ASTER data and field observations has been proposed and tested for deriving surface albedo, surface temperature, Normalized Difference Vegetation Index (NDVI, Modified Soil Adjusted Vegetation Index (MSAVI, vegetation coverage, Leaf Area Index (LAI, net radiation flux, soil heat flux, sensible heat flux and latent heat flux over heterogeneous land surface in this paper. As a case study, the methodology was applied to the experimental area of the Coordinated Enhanced Observing Period (CEOP Asia-Australia Monsoon Project (CAMP on the Tibetan Plateau (CAMP/Tibet, located at the north Tibetan Plateau. The ASTER data of 24 July 2001, 29 November 2001 and 12 March 2002 was used in this paper for the case of summer, winter and spring. To validate the proposed methodology, the ground-measured surface variables (surface albedo and surface temperature and land surface heat fluxes (net radiation flux, soil heat flux, sensible heat flux and latent heat flux were compared to the ASTER derived values. The results show that the derived surface variables and land surface heat fluxes in three different months over the study area are in good accordance with the land surface status. Also, the estimated land surface variables and land surface heat fluxes are in good accordance with ground measurements, and all their absolute percentage difference (APD is less than 10% in the validation sites

  1. Satellite remotely-sensed land surface parameters and their climatic effects on urban areas

    Science.gov (United States)

    Zoran, M.; Savastru, R.; Savastru, D.; Ciobanu, M.; Tautan, M. N.; Miclos, S.

    2009-04-01

    Rapid urbanization transforms the natural landscape to anthropogenic urban land and changes surface biogeophysical characteristics.Urban growth affects the ecology of cities in a number of ways, such as eliminating and fragmenting native habitats, modifying local climate conditions, and generating anthropogenic pollutants.Urbanization has changed many landscapes throughout the world with serious ecological consequences.To understand the ecology of urban systems, it is necessary to quantify the spatial and temporal patterns of urbanization, which often requires dynamic modeling and spatial analysis. Geospatial information provided by satellite remote sensing sensors and biogeophysical field data are very useful for urban landuse-landcover dynamics and impacts analysis. The spatial and spectral variability of urban environments present fundamental challenges to deriving accurate remote sensing information for urban areas. By integrating high-resolution and medium-resolution satellite imagery with other geospatial information, have been investigated several land surface parameters including impervious surfaces and land surface temperatures for Bucharest metropolitan area in Romania. Percent impervious surface was used to quantitatively define the spatial extent and development density of urban land use. Land surface temperatures were retrieved by using a single band algorithm that processes both thermal infrared satellite data and total atmospheric water vapour content. Land surface temperatures have been analysed for different land use and land cover categories both in urban as well as in periurban areas. Because of the removal of vegetative cover and the reduction in evaporation over urban impervious surfaces, the urban heterogeneity of land surface and associated spatial extents influence surface thermal conditions. In situ meteorological data were integrated to assess regional climatic conditions. The spatial structure of surface heating influenced by landscape

  2. Surface and adsorbate structural studies by photoemission in the hν = 50-500 eV range

    International Nuclear Information System (INIS)

    Shirley, D.A.

    1979-08-01

    The present status of photoelectron spectroscopy in the 50-500 eV range is discussed in relation to its application to surface science. Instrumentation aspects of synchrotron radiation sources are reviewed. The direct transition model is shown to be applicable in this range with some limitations. Cooper minima and adsorbate sensitivity enhancement for hν > 100 eV are reviewed. A new effect--condensed phase photoelectron asymmetry--is noted. Finally, photoelectron diffraction - another new effect - is described and evaluated

  3. An autonomous multisensor in situ metrology system for enabling high dynamic range measurement of 3D surfaces on precision machine tools

    International Nuclear Information System (INIS)

    Liu, Samuel M Y; Cheung, Benny C F; Cheng, Ching-Hsiang; Whitehouse, David

    2016-01-01

    An in situ measurement is of prime importance when trying to maintain the position of the workpiece for further compensation processes in order to improve the accuracy and efficiency of the precision machining of three dimensional (3D) surfaces. However, the coordinates of most of the machine tools with closed machine interfaces and control system are not accessible for users, which make it difficult to use the motion axes of the machine tool for in situ measurements. This paper presents an autonomous multisensor in situ metrology system for enabling high dynamic range measurement of 3D surfaces on precision machine tools. It makes use of a designed tool path and an additional motion sensor to assist the registration of time-space data for the position estimation of a 2D laser scanner which measures the surface with a high lateral resolution and large area without the need to interface with the machine tool system. A prototype system was built and integrated into an ultra-precision polishing machine. Experimental results show that it measures the 3D surfaces with high resolution, high repeatability, and large measurement range. The system not only improves the efficiency and accuracy of the precision machining process but also extends the capability of machine tools. (paper)

  4. Application of satellite images analysis to assess the variability of the surface thermal heat island distribution in urban areas

    Directory of Open Access Journals (Sweden)

    Fudała Janina

    2018-01-01

    Full Text Available One of the elements of the urban plans for adapting to climate change is to identify the range the urban heat island (UHI. To a relatively rare ground station network air temperature, one of the possible methods to identify this phenomenon in cities is the analysis of satellite images, and in particular the thermal images surface cities in conjunction with the land-use structure. In the publication is presented the application of indirect methods of determining surface characteristics of heat island in the cities of Upper Silesia Agglomeration on the basis of the analysis of the thermal images from the satellite Landsat for the period 1986-2016. It presents ways to interpret these images depending on the needs of determination the areas sensitive to the impact of the (UHI and define the areas where adaptation actions to the climate change should be undertaken.

  5. Low-surface-area hard carbon anode for na-ion batteries via graphene oxide as a dehydration agent.

    Science.gov (United States)

    Luo, Wei; Bommier, Clement; Jian, Zelang; Li, Xin; Carter, Rich; Vail, Sean; Lu, Yuhao; Lee, Jong-Jan; Ji, Xiulei

    2015-02-04

    Na-ion batteries are emerging as one of the most promising energy storage technologies, particularly for grid-level applications. Among anode candidate materials, hard carbon is very attractive due to its high capacity and low cost. However, hard carbon anodes often suffer a low first-cycle Coulombic efficiency and fast capacity fading. In this study, we discover that doping graphene oxide into sucrose, the precursor for hard carbon, can effectively reduce the specific surface area of hard carbon to as low as 5.4 m(2)/g. We further reveal that such doping can effectively prevent foaming during caramelization of sucrose and extend the pyrolysis burnoff of sucrose caramel over a wider temperature range. The obtained low-surface-area hard carbon greatly improves the first-cycle Coulombic efficiency from 74% to 83% and delivers a very stable cyclic life with 95% of capacity retention after 200 cycles.

  6. Application of satellite images analysis to assess the variability of the surface thermal heat island distribution in urban areas

    Science.gov (United States)

    Fudała, Janina; Nádudvari, Ádám; Bronder, Joachim; Fudała, Marta

    2018-01-01

    One of the elements of the urban plans for adapting to climate change is to identify the range the urban heat island (UHI). To a relatively rare ground station network air temperature, one of the possible methods to identify this phenomenon in cities is the analysis of satellite images, and in particular the thermal images surface cities in conjunction with the land-use structure. In the publication is presented the application of indirect methods of determining surface characteristics of heat island in the cities of Upper Silesia Agglomeration on the basis of the analysis of the thermal images from the satellite Landsat for the period 1986-2016. It presents ways to interpret these images depending on the needs of determination the areas sensitive to the impact of the (UHI) and define the areas where adaptation actions to the climate change should be undertaken.

  7. Low-Surface-Area Hard Carbon Anode for Na-Ion Batteries via Graphene Oxide as a Dehydration Agent

    Energy Technology Data Exchange (ETDEWEB)

    Luo, W; Bommier, C; Jian, ZL; Li, X; Carter, R; Vail, S; Lu, YH; Lee, JJ; Ji, XL

    2015-02-04

    Na-ion batteries are emerging as one of the most promising energy storage technologies, particularly for grid-level applications. Among anode candidate materials, hard carbon is very attractive due to its high capacity and low cost. However, hard carbon anodes often suffer a low first-cycle Coulombic efficiency and fast capacity fading. In this study, we discover that doping graphene oxide into sucrose, the precursor for hard carbon, can effectively reduce the specific surface area of hard carbon to as low as 5.4 m(2)/g. We further reveal that such doping can effectively prevent foaming during caramelization of sucrose and extend the pyrolysis burnoff of sucrose caramel over a wider temperature range. The obtained low-surface-area hard carbon greatly improves the first-cycle Coulombic efficiency from 74% to 83% and delivers a very stable cyclic life with 95% of capacity retention after 200 cycles.

  8. Pore scale heterogeneity in the mineral distribution and reactive surface area of rocks

    Science.gov (United States)

    Lai, P. E.; Krevor, S. C.

    2013-12-01

    There are long-standing challenges in characterizing reactive transport in porous media at scales larger than individual pores. This hampers the prediction of the field-scale impact of geochemical processes on fluid flow [1]. This is a source of uncertainty for CO2 injection, which results in a reactive fluid-rock system, particularly in carbonate rock reservoirs. A potential cause is the inability of the continuum approach to incorporate the impact of heterogeneity in pore-scale reaction rates. This results in part from pore-scale heterogeneities in surface area of reactive minerals [2,3]. In this study we have created μm resolution 3D images of 3 sandstone and 4 carbonate rocks using x-ray microtomography. Using in-house image processing techniques and auxiliary characterisation with thin section, electron microscope and spectroscopic techniques we quantified the surface area of each mineral phase in the x-ray CT images. This quantification was validated against N2 BET surface area and He porosity measurements of the imaged samples. Distributions in reactive surface area for each mineral phase were constructed by calculating surface areas in thousands of randomly selected subvolume images of the total sample, each normalized to the pore volume in that image. In all samples, there is little correlation between the reactive surface area fraction and the volumetric fraction of a mineral in a bulk rock. Berea sandstone was far less heterogeneous and has a characteristic pore size at which a surface area distribution may be used to quantify heterogeneity. In carbonates, heterogeneity is more complex and surface area must be characterized at multiple length scales for an accurate description of reactive transport. [1] Maher, Steefel, Depaolo and Vianni (2006) Geochimica et Cosmochimica Acta, 70, 337-363 [2] Landrot, Ajo-Franklin, Yang, Cabrini and Steefel (2012) Chemical Geology 318-319, 113-125 [3] Li, Peters and Celia (2007) American Journal of Science 307, 1146

  9. Variability of silver fir (Abies alba Mill. cones – variability structure of scale surface area

    Directory of Open Access Journals (Sweden)

    Aniszewska Monika

    2017-03-01

    Full Text Available This study was conducted on a batch of closed silver fir cones from Jawor Forest District and a mixture of scales from the seed extraction facility Grotniki. The scales were divided into three size classes corresponding to the bottom, middle and upper part of the cones and their area was measured with the Multi Scan Base v.18.03 software. Based on the sum of the inner and outer surface area of all scales, we then determined the total area of evaporation from the cones. In addition, the area of protruding scales was measured for differently sized scales from different parts of the cones. Previous studies have shown that the average outer surface of a closed cone, calculated as the sum of protruding scales, accounts for 10% of the outer surface of an open cone. Pictures of both scale surfaces with the internal seed bed and the external protrusions were taken using a scanning electron microscope. We noticed significant differences in dimension and shape of the channels and trichomes on the scale surface. On the inner side of the scales, we found a high diversity of trichomes of different lengths, whilst the outer side contained channels. Presumably, these characteristics affect the rate of water loss from the cones during desiccation and separation of the seed. In-depth knowledge on the evaporative surfaces of fir cones and scale structure will be helpful for optimizing the industrial processes of seed extraction.

  10. Entanglement contour perspective for "strong area-law violation" in a disordered long-range hopping model

    Science.gov (United States)

    Roy, Nilanjan; Sharma, Auditya

    2018-03-01

    We numerically investigate the link between the delocalization-localization transition and entanglement in a disordered long-range hopping model of spinless fermions by studying various static and dynamical quantities. This includes the inverse participation ratio, level statistics, entanglement entropy, and number fluctuations in the subsystem along with quench and wave-packet dynamics. Finite systems show delocalized, quasilocalized, and localized phases. The delocalized phase shows strong area-law violation, whereas the (quasi)localized phase adheres to (for large subsystems) the strict area law. The idea of "entanglement contour" nicely explains the violation of area law and its relationship with "fluctuation contour" reveals a signature at the transition point. The relationship between entanglement entropy and number fluctuations in the subsystem also carries signatures for the transition in the model. Results from the Aubry-Andre-Harper model are compared in this context. The propagation of charge and entanglement are contrasted by studying quench and wave-packet dynamics at the single-particle and many-particle levels.

  11. Evaluating polymer degradation with complex mixtures using a simplified surface area method.

    Science.gov (United States)

    Steele, Kandace M; Pelham, Todd; Phalen, Robert N

    2017-09-01

    Chemical-resistant gloves, designed to protect workers from chemical hazards, are made from a variety of polymer materials such as plastic, rubber, and synthetic rubber. One material does not provide protection against all chemicals, thus proper polymer selection is critical. Standardized testing, such as chemical degradation tests, are used to aid in the selection process. The current methods of degradation ratings based on changes in weight or tensile properties can be expensive and data often do not exist for complex chemical mixtures. There are hundreds of thousands of chemical products on the market that do not have chemical resistance data for polymer selection. The method described in this study provides an inexpensive alternative to gravimetric analysis. This method uses surface area change to evaluate degradation of a polymer material. Degradation tests for 5 polymer types against 50 complex mixtures were conducted using both gravimetric and surface area methods. The percent change data were compared between the two methods. The resulting regression line was y = 0.48x + 0.019, in units of percent, and the Pearson correlation coefficient was r = 0.9537 (p ≤ 0.05), which indicated a strong correlation between percent weight change and percent surface area change. On average, the percent change for surface area was about half that of the weight change. Using this information, an equivalent rating system was developed for determining the chemical degradation of polymer gloves using surface area.

  12. Analysis of relationships between NDVI and land surface temperature in coastal area

    Science.gov (United States)

    Ning, Jicai; Gao, Zhiqiang; Chen, Maosi

    2017-09-01

    Using Landsat 5 Thematic Mapper and Landsat 8 Operational Land Imager and Thermal Infrared Sensor imagery of the Yellow River Delta, this study analyzed the relationships between NDVI and LST (land surface temperature). Six Landsat images comprising two time series were used to calculate the land surface temperature and correlated vegetation indices. The Yellow River Delta area has expanded substantially because of the deposited sediment carried from upstream reaches of the river. Between 1986 and 2015, approximately 35% of the land use area of the Yellow River Delta has been transformed into salterns and aquaculture ponds. Overall, land use conversion has occurred primarily from poorly utilized land into highly utilized land. To analyze the variation of land surface temperature, a mono-window algorithm was applied to retrieve the regional land surface temperature. The results showed bilinear correlation between land surface temperature and the vegetation indices (i.e., Normalized Difference Vegetation Index, Adjusted-Normalized Vegetation Index, Soil-Adjusted Vegetation Index, and Modified Soil-Adjusted Vegetation Index). Generally, values of the vegetation indices greater than the inflection point mean the land surface temperature and the vegetation indices are correlated negatively, and vice versa. Land surface temperature in coastal areas is affected considerably by local seawater temperature and weather conditions.

  13. Relationship among land surface temperature and LUCC, NDVI in typical karst area.

    Science.gov (United States)

    Deng, Yuanhong; Wang, Shijie; Bai, Xiaoyong; Tian, Yichao; Wu, Luhua; Xiao, Jianyong; Chen, Fei; Qian, Qinghuan

    2018-01-12

    Land surface temperature (LST) can reflect the land surface water-heat exchange process comprehensively, which is considerably significant to the study of environmental change. However, research about LST in karst mountain areas with complex topography is scarce. Therefore, we retrieved the LST in a karst mountain area from Landsat 8 data and explored its relationships with LUCC and NDVI. The results showed that LST of the study area was noticeably affected by altitude and underlying surface type. In summer, abnormal high-temperature zones were observed in the study area, perhaps due to karst rocky desertification. LSTs among different land use types significantly differed with the highest in construction land and the lowest in woodland. The spatial distributions of NDVI and LST exhibited opposite patterns. Under the spatial combination of different land use types, the LST-NDVI feature space showed an obtuse-angled triangle shape and showed a negative linear correlation after removing water body data. In summary, the LST can be retrieved well by the atmospheric correction model from Landsat 8 data. Moreover, the LST of the karst mountain area is controlled by altitude, underlying surface type and aspect. This study provides a reference for land use planning, ecological environment restoration in karst areas.

  14. Surface Area of Patellar Facets: Inferential Statistics in the Iraqi Population

    Directory of Open Access Journals (Sweden)

    Ahmed Al-Imam

    2017-01-01

    Full Text Available Background. The patella is the largest sesamoid bone in the body; its three-dimensional complexity necessitates biomechanical perfection. Numerous pathologies occur at the patellofemoral unit which may end in degenerative changes. This study aims to test the presence of statistical correlation between the surface areas of patellar facets and other patellar morphometric parameters. Materials and Methods. Forty dry human patellae were studied. The morphometry of each patella was measured using a digital Vernier Caliper, electronic balance, and image analyses software known as ImageJ. The patellar facetal surface area was correlated with patellar weight, height, width, and thickness. Results. Inferential statistics proved the existence of linear correlation of total facetal surface area and patellar weight, height, width, and thickness. The correlation was strongest for surface area versus patellar weight. The lateral facetal area was found persistently larger than the medial facetal area, the p value was found to be <0.001 (one-tailed t-test for right patellae, and another significant p value of < 0.001 (one-tailed t-test was found for left patellae. Conclusion. These data are vital for the restoration of the normal biomechanics of the patellofemoral unit; these are to be consulted during knee surgeries and implant designs and can be of an indispensable anthropometric, interethnic, and biometric value.

  15. Accuracy of Reconstruction of the Tree Stem Surface Using Terrestrial Close-Range Photogrammetry

    Directory of Open Access Journals (Sweden)

    Peter Surový

    2016-02-01

    Full Text Available Airborne laser scanning (ALS allows for extensive coverage, but the accuracy of tree detection and form can be limited. Although terrestrial laser scanning (TLS can improve on ALS accuracy, it is rather expensive and area coverage is limited. Multi-view stereopsis (MVS techniques combining computer vision and photogrammetry may offer some of the coverage benefits of ALS and the improved accuracy of TLS; MVS combines computer vision research and automatic analysis of digital images from common commercial digital cameras with various algorithms to reconstruct three-dimensional (3D objects with realistic shape and appearance. Despite the relative accuracy (relative geometrical distortion of the reconstructions available in the processing software, the absolute accuracy is uncertain and difficult to evaluate. We evaluated the data collected by a common digital camera through the processing software (Agisoft PhotoScan © for photogrammetry by comparing those by direct measurement of the 3D magnetic motion tracker. Our analyses indicated that the error is mostly concentrated in the portions of the tree where visibility is lower, i.e., the bottom and upper parts of the stem. For each reference point from the digitizer we determined how many cameras could view this point. With a greater number of cameras we found increasing accuracy of the measured object space point positions (as expected, with a significant positive change in the trend beyond five cameras; when more than five cameras could view this point, the accuracy began to increase more abruptly, but eight cameras or more provided no increases in accuracy. This method allows for the retrieval of larger datasets from the measurements, which could improve the accuracy of estimates of 3D structure of trees at potentially reduced costs.

  16. Levels and isomer profiles of Dechlorane Plus in the surface soils from e-waste recycling areas and industrial areas in South China

    Energy Technology Data Exchange (ETDEWEB)

    Yu Zhiqiang [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Lu Shaoyou; Gao Shutao; Wang Jingzhi [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100039 (China); Li Huiru, E-mail: huiruli@gig.ac.c [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Zeng Xiangying; Sheng Guoying; Fu Jiamo [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)

    2010-09-15

    Dechlorane Plus (DP) is a highly chlorinated flame retardant. Levels of DP were measured in surface soils from e-waste recycling areas and industrial areas in South China. Higher DP levels were found in e-waste recycling areas (undetectable-47.4 ng/g) than those in industrial areas (0.0336-4.65 ng/g) in South China. The highest DP concentration (3327 ng/g) was found at the e-waste recycling site in Qingyuan, while DP levels fell dramatically with increasing distance away from the recycling site, suggesting that the e-waste recycling activities are an important source of DP emissions. The mean ratios of anti-DP to total DP (f{sub anti}) for different sampling areas ranged from 0.58 to 0.76 and showed no significant difference from the ratio for the technical DP products (t-test, p > 0.05). Further intensive studies are needed to investigate the process of DP degradation and its degradation products. - High DP concentrations were found in the soils from e-waste recycling regions, and e-waste recycling was the major source of DP emissions in South China.

  17. Corrective Action Plan for Corrective Action Unit 428: Area 3 Septic Waste Systems 1 and 5 Tonopah Test Range, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    D. S. Tobiason

    2000-08-01

    Area 3 Septic Waste Systems 1 and 5 are located in Area 3 of the Tonopah Test Range (TTR) (Figure 1). The site is listed in the Federal Facility Agreement and Consent Order (FFACO, 1996) as Corrective Action Unit (CAU) 428 and includes Corrective Action Sites 03-05-002-SW01 (Septic Waste System 1 [SWS 1]), and 03-05-002-SW05 (Septic Waste System 5 [SWS 5]). The site history for the CAU is provided in the Corrective Action Investigation Plan (U.S. Department of Energy, Nevada Operations Office [DOE/NV], 1999). SWS 1 consists of two leachfields and associated septic tanks. SWS 1 received effluent from both sanitary and industrial sources from various buildings in Area 3 of the TTR (Figure 2). SWS 5 is comprised of one leachfield and outfall with an associated septic tank. SWS 5 received effluent from sources in Building 03-50 in Area 3 of the TTR (Figure 2). Both systems were active until 1990 when a consolidated sewer system was installed. The purpose of this Corrective Action Plan (CAP) is to provide the strategy and methodology to close the Area 3 SWS 1 and 5. The CAU will be closed following state and federal regulations and the FFACO (1996). Site characterization was done during May and June 1999. Samples of the tank contents, leachfield soil, and soil under the tanks and pipes were collected. The results of the characterization were reported in the Corrective Action Decision Document (CADD) (DOE/NV, 2000). Additional sampling was done in May 2000, the results of which are presented in this plan. Soil sample results indicated that two constituents of concern were detected above Preliminary Action Levels (PALs). Total arsenic was detected at a concentration of 68.7 milligrams per kilogram (mg/kg). The arsenic was found under the center distribution line at the proximal end of the SWS 5 Leachfield (Figure 3). Total benzo(a)pyrene was detected at a concentration of 480 micrograms per kilogram ({micro}g/kg). The benzo(a)pyrene was found in the soil under the

  18. Scaling of Haversian canal surface area to secondary osteon bone volume in ribs and limb bones.

    Science.gov (United States)

    Skedros, John G; Knight, Alex N; Clark, Gunnar C; Crowder, Christian M; Dominguez, Victoria M; Qiu, Shijing; Mulhern, Dawn M; Donahue, Seth W; Busse, Björn; Hulsey, Brannon I; Zedda, Marco; Sorenson, Scott M

    2013-06-01

    Studies of secondary osteons in ribs have provided a great deal of what is known about remodeling dynamics. Compared with limb bones, ribs are metabolically more active and sensitive to hormonal changes, and receive frequent low-strain loading. Optimization for calcium exchange in rib osteons might be achieved without incurring a significant reduction in safety factor by disproportionally increasing central canal size with increased osteon size (positive allometry). By contrast, greater mechanical loads on limb bones might favor reducing deleterious consequences of intracortical porosity by decreasing osteon canal size with increased osteon size (negative allometry). Evidence of this metabolic/mechanical dichotomy between ribs and limb bones was sought by examining relationships between Haversian canal surface area (BS, osteon Haversian canal perimeter, HC.Pm) and bone volume (BV, osteonal wall area, B.Ar) in a broad size range of mature (quiescent) osteons from adult human limb bones and ribs (modern and medieval) and various adult and subadult non-human limb bones and ribs. Reduced major axis (RMA) and least-squares (LS) regressions of HC.Pm/B.Ar data show that rib and limb osteons cannot be distinguished by dimensional allometry of these parameters. Although four of the five rib groups showed positive allometry in terms of the RMA slopes, nearly 50% of the adult limb bone groups also showed positive allometry when negative allometry was expected. Consequently, our results fail to provide clear evidence that BS/BV scaling reflects a rib versus limb bone dichotomy whereby calcium exchange might be preferentially enhanced in rib osteons. Copyright © 2013 Wiley Periodicals, Inc.

  19. Quality of surface-water supplies in the Triangle area of North Carolina, water year 2009

    Science.gov (United States)

    Pfeifle, C. A.; Giorgino, M. J.; Rasmussen, R. B.

    2014-01-01

    Surface-water supplies are important sources of drinking water for residents in the Triangle area of North Carolina, which is located within the upper Cape Fear and Neuse River Basins. Since 1988, the U.S. Geological Survey and a consortium of governments have tracked water-quality conditions and trends in several of the area’s water-supply lakes and streams. This report summarizes data collected through this cooperative effort, known as the Triangle Area Water Supply Monitoring Project, during October 2008 through September 2009. Major findings for this period include: - Annual precipitation was approximately 20 percent below the long-term mean (average) annual precipitation. - Streamflow was below the long-term mean at the 10 project streamgages during most of the year. - More than 7,000 individual measurements of water quality were made at a total of 26 sites—15 in the Neuse River Basin and 11 in the Cape Fear River Basin. Forty-seven water-quality properties and constituents were measured. - All observations met North Carolina water-quality standards for water temperature, pH, hardness, chloride, fluoride, sulfate, nitrate, arsenic, cadmium, chromium, lead, nickel, and selenium. - North Carolina water-quality standards were exceeded one or more times for dissolved oxygen, dissolved oxygen percent saturation, chlorophyll a, mercury, copper, iron, manganese, silver, and zinc. Exceedances occurred at 23 sites—13 in the Neuse River Basin and 10 in the Cape Fear River Basin. - Stream samples collected during storm events contained elevated concentrations of 18 water-quality constituents compared to samples collected during non-storm events. - Concentrations of nitrogen and phosphorus were within ranges observed during previous years. - Five reservoirs had chlorophyll a concentrations in excess of 40 micrograms per liter at least once during 2009: Little River Reservoir, Falls Lake, Cane Creek Reservoir, University Lake, and Jordan Lake.

  20. Correlating humidity-dependent ionically conductive surface area with transport phenomena in proton-exchange membranes.

    Science.gov (United States)

    He, Qinggang; Kusoglu, Ahmet; Lucas, Ivan T; Clark, Kyle; Weber, Adam Z; Kostecki, Robert

    2011-10-13

    The objective of this effort was to correlate the local surface ionic conductance of a Nafion 212 proton-exchange membrane with its bulk and interfacial transport properties as a function of water content. Both macroscopic and microscopic proton conductivities were investigated at different relative humidity levels, using direct-current voltammetry and current-sensing atomic force microscopy (CSAFM). We were able to identify small ion-conducting domains that grew with humidity at the surface of the membrane. Numerical analysis of the surface ionic conductance images recorded at various relative humidity levels helped determine the fractional area of ion-conducting active sites. A simple square-root relationship between the fractional conducting area and observed interfacial mass-transport resistance was established. Furthermore, the relationship between the bulk ionic conductivity and surface ionic conductance pattern of the Nafion membrane was examined.

  1. Correlating Humidity-Dependent Ionically Conductive Surface Area with Transport Phenomena in Proton-Exchange Membranes

    Energy Technology Data Exchange (ETDEWEB)

    He, Qinggang; Kusoglu, Ahmet; Lucas, Ivan T.; Clark, Kyle; Weber, Adam Z.; Kostecki, Robert

    2011-08-01

    The objective of this effort was to correlate the local surface ionic conductance of a Nafion? 212 proton-exchange membrane with its bulk and interfacial transport properties as a function of water content. Both macroscopic and microscopic proton conductivities were investigated at different relative humidity levels, using electrochemical impedance spectroscopy and current-sensing atomic force microscopy (CSAFM). We were able to identify small ion-conducting domains that grew with humidity at the surface of the membrane. Numerical analysis of the surface ionic conductance images recorded at various relative humidity levels helped determine the fractional area of ion-conducting active sites. A simple square-root relationship between the fractional conducting area and observed interfacial mass-transport resistance was established. Furthermore, the relationship between the bulk ionic conductivity and surface ionic conductance pattern of the Nafion? membrane was examined.

  2. Geohydrology and susceptibility of major aquifers to surface contamination in Alabama; area 11

    Science.gov (United States)

    Castleberry, R.D.; Moreland, R.S.; Scott, J.C.

    1989-01-01

    This report delineates and describes the geohydrology and susceptibility of major aquifers to contamination in Butler, Conecuh, Covington, Crenshaw, Escambia, and Monroe Counties, Alabama. The major aquifers are the Pliocene-Miocene, Upper Floridan, Lisbon, Nanafalia-Clayton, and Providence-Ripley. The largest pumping centers in the area are Andalusia and Monroeville, where groundwater use is about 5 and 4 million gal/day, respectively. Estimated maximum withdrawal in 1987 for all uses in the area was about 44 million gal/day. Depressions have developed in the potentiometric surfaces of the Lisbon aquifer near Andalusia and Opp, the Nanafalia-Clayton aquifer near Luverne, Andalusia, Beatrice, and Monroeville, and the Providence-Ripley aquifer at Greenville. Significant declines in the potentiometric surfaces of the other major aquifers are not apparent. Recharge areas for all major aquifers are susceptible to contamination, but the probability of contamination of the Lisbon, Nanafalia-Clayton, and Providence-Ripley aquifers is low because the recharge areas are remote from areas of the withdrawal. The depressions in the recharge area for the Upper Floridan aquifer and the area where the Pliocene-Miocene aquifer is overlain by the gravelly sands of the Citronelle Formation are highly susceptible to contamination from the surface. (USGS)

  3. Microbiology of the surface water samples in the high background radiation areas of Ramsar, Iran

    International Nuclear Information System (INIS)

    Motamedifar, Mohammad; Zamani, Khosrow; Sedigh, Hadi; Mortazavi, Seyed Mohammad Javad; Taeb, Shahram; Haghani, M.; Mortazavi, Seyed Ali Reza; Soofi, Amir

    2014-01-01

    Residents of high background radiation areas of Ramsar have lived in these areas for many generations and received radiation doses much higher than the dose limit recommended by ICRP for radiation workers. The radioactivity of the high background radiation areas of Ramsar is reported to be due to 226 Ra and its decay products, which have been brought to the surface by the waters of hot springs. Over the past years the department has focused on different aspects of the health effects of the elevated levels of natural radiation in Ramsar. This study was aimed to perform a preliminary investigation on the bioeffects of exposure to elevated levels of natural radiation on the microbiology of surface water samples. Water samples were collected from surface water streams in Talesh Mahalleh district, Ramsar as well as a nearby area with normal levels of background radiation. Only two strains of bacteria, that is, Providencia stuartii and Shimwellia blattae, could be isolated from the water samples collected from high background radiation areas, while seven strains (Escherichia coli, Enterobacter asburiae, Klebsiella pneumoniae, Shigella dysenteriae, Buttiauxella agerstis, Tatumella punctuata and Raoultella ornithinolytica) were isolated from the water samples collected from normal background radiation areas. All the bacteria isolated from water samples of high and normal background radiation areas were sensitive to ultraviolet radiation, heat, betadine, alcohol, and deconex. Although other investigators have reported that bacteria isolated from hot springs show radioresistance, the results reported here do not reveal any adaptive response. (author)

  4. A Three-Dimensional Enormous Surface Area Aluminum Microneedle Array with Nanoporous Structure

    OpenAIRE

    Chen, Po Chun; Hsieh, Sheng Jen; Chen, Chien Chon; Zou, Jun

    2013-01-01

    We proposed fabricating an aluminum microneedle array with a nanochannel structure on the surface by combining micromachining, electrolyte polishing, and anodization methods. The microneedle array provides a three-dimensional (3D) structure that possesses several hundred times more surface area than a traditional nanochannel template. Therefore, the microneedle array can potentially be used in many technology applications. This 3D microneedle array device can not only be used for painless inj...

  5. Area-averaged surface fluxes and their time-space variability over the FIFE experimental domain

    Science.gov (United States)

    Smith, E. A.; Hsu, A. Y.; Crosson, W. L.; Field, R. T.; Fritschen, L. J.; Gurney, R. J.; Kanemasu, E. T.; Kustas, W. P.; Nie, D.; Shuttleworth, W. J.

    1992-01-01

    The underlying mean and variance properties of surface net radiation, sensible-latent heat fluxes and soil heat flux are studied over the densely instrumented grassland region encompassing FIFE. Flux variability is discussed together with the problem of scaling up to area-averaged fluxes. Results are compared and contrasted for cloudy and clear situations and examined for the influence of surface-induced biophysical controls (burn and grazing treatments) and topographic controls (aspect ratios and slope factors).

  6. Closure Report for Corrective Action Unit 408: Bomblet Target Area Tonopah Test Range (TTR), Nevada, Revision 0

    Energy Technology Data Exchange (ETDEWEB)

    Mark Krauss

    2010-09-01

    This Closure Report (CR) presents information supporting the closure of Corrective Action Unit (CAU) 408: Bomblet Target Area (TTR), Tonopah Test Range, Nevada. This CR complies with the requirements of the Federal Facility Agreement and Consent Order that was agreed to by the State of Nevada; U.S. Department of Energy (DOE), Environmental Management; U.S. Department of Defense; and DOE, Legacy Management. Corrective Action Unit 408 is located at the Tonopah Test Range, Nevada, and consists of Corrective Action Site (CAS) TA-55-002-TAB2, Bomblet Target Areas. This CAS includes the following seven target areas: • Mid Target • Flightline Bomblet Location • Strategic Air Command (SAC) Target Location 1 • SAC Target Location 2 • South Antelope Lake • Tomahawk Location 1 • Tomahawk Location 2 The purpose of this CR is to provide documentation supporting the completed corrective actions and data confirming that the closure objectives for the CAS within CAU 408 were met. To achieve this, the following actions were performed: • Review the current site conditions, including the concentration and extent of contamination. • Implement any corrective actions necessary to protect human health and the environment. • Properly dispose of corrective action and investigation wastes. • Document Notice of Completion and closure of CAU 408 issued by the Nevada Division of Environmental Protection. From July 2009 through August 2010, closure activities were performed as set forth in the Streamlined Approach for Environmental Restoration Plan for CAU 408: Bomblet Target Area, Tonopah Test Range (TTR), Nevada. The purposes of the activities as defined during the data quality objectives process were as follows: • Identify and remove munitions of explosive concern (MEC) associated with DOE activities. • Investigate potential disposal pit locations. • Remove depleted uranium-contaminated fragments and soil. • Determine whether contaminants of concern (COCs) are

  7. Volumes, Masses, and Surface Areas for Shippingport LWBR Spent Nuclear Fuel in a DOE SNF Canister

    International Nuclear Information System (INIS)

    J.W. Davis

    1999-01-01

    The purpose of this calculation is to estimate volumes, masses, and surface areas associated with (a) an empty Department of Energy (DOE) 18-inch diameter, 15-ft long spent nuclear fuel (SNF) canister, (b) an empty DOE 24-inch diameter, 15-ft long SNF canister, (c) Shippingport Light Water Breeder Reactor (LWBR) SNF, and (d) the internal basket structure for the 18-in. canister that has been designed specifically to accommodate Seed fuel from the Shippingport LWBR. Estimates of volumes, masses, and surface areas are needed as input to structural, thermal, geochemical, nuclear criticality, and radiation shielding calculations to ensure the viability of the proposed disposal configuration

  8. Pore Scale Heterogeneity in the Mineral Distribution, Surface Area and Adsorption in Porous Rocks

    Science.gov (United States)

    Lai, P. E. P.; Krevor, S. C.

    2014-12-01

    The impact of heterogeneity in chemical transport and reaction is not understood in continuum (Darcy/Fickian) models of reactive transport. This is manifested in well-known problems such as scale dependent dispersion and discrepancies in reaction rate observations made at laboratory and field scales [1]. Additionally, this is a source of uncertainty for carbon dioxide injection, which produces a reactive fluid-rock system particularly in carbonate rock reservoirs. A potential cause is the inability of the continuum approach to incorporate the impact of heterogeneity in pore-scale reaction rates. This results in part from pore-scale heterogeneities in surface area of reactive minerals [2, 3]. We use x-ray micro tomography to describe the non-normal 3-dimensional distribution of reactive surface area within a porous medium according to distinct mineral groups. Using in-house image processing techniques, thin sections, nitrogen BET surface area, backscattered electron imaging and energy dispersive spectroscopy, we compare the surface area of each mineral phase to those obtained from x-ray CT imagery. In all samples, there is little correlation between the reactive surface area fraction and the volumetric fraction of a mineral in a bulk rock. Berea sandstone was far less heterogeneous and has a characteristic pore size at which a surface area distribution may be used to quantify heterogeneity. In carbonates, heterogeneity is more complex and surface area must be characterized at multiple length scales for an accurate description of reactive transport. We combine the mineral specific surface area characterisation to dynamic tomography, imaging the flow of water and solutes, to observe flow dependent and mineral specific adsorption. The observations may contribute to the incorporation of experimentally based statistical descriptions of pore scale heterogeneity in reactive transport into upscaled models, moving it closer to predictive capabilities for field scale

  9. A process to enhance the specific surface area and capacitance of hydrothermally reduced graphene oxide

    KAUST Repository

    Alazmi, Amira

    2016-08-26

    The impact of post-synthesis processing in reduced graphene oxide materials for supercapacitor electrodes has been analyzed. A comparative study of vacuum, freeze and critical point drying was carried out for hydrothermally reduced graphene oxide demonstrating that the optimization of the specific surface area and preservation of the porous network are critical to maximize its supercapacitance performance. As described below, using a supercritical fluid as the drying medium, unprecedented values of the specific surface area (364 m2 g−1) and supercapacitance (441 F g−1) for this class of materials have been achieved.

  10. N2-specific surface area of ZrO2-montmorillonite MK-10 synthesis

    International Nuclear Information System (INIS)

    Muzakky; Imam Proyogo

    2016-01-01

    A measurements of N 2 -specific surface area of ZrO 2 -montmorillonite MK-10 synthesis have been done. The purpose of this study is to observed the effect of calcination on the a specific surface area (SSA N2 -BET) of ZrO 2 -montmorillonite MK-10 synthesis. Calcination were carried out at a 200°C; 400°C and 700°C. While the observations were made with surface area analyzer (SAA) and transmission electron microscopy (TEM). The measurement results obtained that SSA N2 -BET ZrO 2 -MK-10 obtained at 214 m 2 g -1 for before calcination and 195 m 2 g -1 after calcination at 400°C. The effected of calcination temperature will cause more towards of multilayer system surface, but the distribution of pore volume becomes smaller. Result of visualization of ZrO 2 -MK-10 surface that by means of TEM showed before calcination are more transparent and has a pore more. While calcination at 400°C has a darker impression and became multilayer and have a larger volume. Synthesized of ZrO 2 -MK 10 that using the ethylene glycol precursor have SSA N2 -BET higher than using glycerol is 195.33 m 2 g -1 and more memorable surface of a solid compact and orderly. (author)

  11. Observation of contact area of bubbles with heating surface in pool boiling of water under microgravity

    International Nuclear Information System (INIS)

    Suzuki, K.; Kawamura, H.; Suzuki, M.; Takahashi, S.; Abe, Y.

    2003-01-01

    Burnout heat flux was measured in subcooled pool boiling of water under attached boiling bubbles on heating surface with bubble holding plate in ground experiment. A thin stainless flat plate was employed for heating surface. The experimental setup and the heating procedures were same as used in reduced gravity experiment performed by a parabolic flight of jet aircraft. Same burnout heat flux as in the reduced gravity was obtained by adjusting the clearance between the bubble holder and the heating surface. They were 100 ∝ 400 percent higher than the widely accepted existing theories. As extending heating time longer than the reduced gravity duration until burnout occurred, burnout heat flux decreased gradually and became a constant value calculated from the existing theories. In a result of observing contact area of boiling bubbles with transparent heating surface, the contact area was smaller in quick heating time than that in long time heating at same heat flux. The experimental results suggest in microgravity that liquid layer is remained between rapidly expanded bubbles and heating surface. In microgravity experiment by a drop shaft facility, contact area of bubbles with heating surface increased considerably at starting of microgravity. (orig.)

  12. City landscape changes effects on land surface temperature in Bucharest metropolitan area

    Science.gov (United States)

    Savastru, Dan M.; Zoran, Maria A.; Savastru, Roxana S.; Dida, Adrian I.

    2017-10-01

    This study investigated the influences of city land cover changes and extreme climate events on land surface temperature in relationship with several biophysical variables in Bucharest metropolitan area of Romania through satellite and in-situ monitoring data. Remote sensing data from IKONOS, Landsat TM/ETM+ and time series MODIS Terra/Aqua and NOAA AVHRR sensors have been used to assess urban land cover- temperature interactions over 2000 - 2016 period. Time series Thermal InfraRed (TIR) satellite remote sensing data in synergy with meteorological data (air temperatureAT, precipitations, wind, solar radiation, etc.) were applied mainly for analyzing land surface temperature (LST) pattern and its relationship with surface landscape characteristics, assessing urban heat island (UHI), and relating urban land cover temperatures (LST). The land surface temperature, a key parameter for urban thermal characteristics analysis, was also analyzed in relation with the Normalized Difference Vegetation Index (NDVI) at city level. Results show that in the metropolitan area ratio of impervious surface in Bucharest increased significantly during investigated period, the intensity of urban heat island and heat wave events being most significant. The correlation analyses revealed that, at the pixel-scale, LST and AT possessed a strong positive correlation with percent impervious surfaces and negative correlation with vegetation abundances at metropolitan scale respectively. The NDVI was significantly correlated with precipitation. The spatial average air temperatures in urban test areas rise with the expansion of the urban size.

  13. Description of surface systems. Preliminary site description Simpevarp sub area - Version 1.2

    International Nuclear Information System (INIS)

    Lindborg, Tobias

    2005-03-01

    Swedish Nuclear Fuel and Waste Management Co is currently conducting site characterisation in the Simpevarp area. The area is divided into two subareas, the Simpevarp and the Laxemar subarea. The two subareas are surrounded by a common regional model area, the Simpevarp area. This report describes both the regional area and the subareas. This report is an interim version (model version 1.2) of the description of the surface systems at the Simpevarp area, and should be seen as a background report to the site description of the Simpevarp area, version 1.2, SKB-R--05-08. The basis for this description is quality-assured field data available in the SKB SICADA and GIS databases, together with generic data from the literature. The Surface system, here defined as everything above the bedrock, comprises a number of separate disciplines (e.g. hydrology, geology, topography, oceanography and ecology). Each discipline has developed descriptions and models for a number of properties that together represent the site description. The current methodology for developing the surface system description and the integration to ecosystem models is documented in a methodology strategy report SKB-R--03-06. The procedures and guidelines given in that report were followed in this report. Compared with version 1.1 of the surface system description SKB-R--04-25, this report presents considerable additional features, especially in the ecosystem description (Chapter 4) and in the description of the surface hydrology (Section 3.4). A first attempt has also been made to connect the flow of matter (carbon) between the different ecosystems into an overall ecosystem model at a landscape level. A summarised version of this report is also presented in SKB-R--05-08 together with geological-, hydrogeological-, transport properties-, thermal properties-, rock mechanics- and hydrogeochemical descriptions

  14. Description of surface systems. Preliminary site description Simpevarp sub area - Version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Lindborg, Tobias (ed.)

    2005-03-01

    Swedish Nuclear Fuel and Waste Management Co is currently conducting site characterisation in the Simpevarp area. The area is divided into two subareas, the Simpevarp and the Laxemar subarea. The two subareas are surrounded by a common regional model area, the Simpevarp area. This report describes both the regional area and the subareas. This report is an interim version (model version 1.2) of the description of the surface systems at the Simpevarp area, and should be seen as a background report to the site description of the Simpevarp area, version 1.2, SKB-R--05-08. The basis for this description is quality-assured field data available in the SKB SICADA and GIS databases, together with generic data from the literature. The Surface system, here defined as everything above the bedrock, comprises a number of separate disciplines (e.g. hydrology, geology, topography, oceanography and ecology). Each discipline has developed descriptions and models for a number of properties that together represent the site description. The current methodology for developing the surface system description and the integration to ecosystem models is documented in a methodology strategy report SKB-R--03-06. The procedures and guidelines given in that report were followed in this report. Compared with version 1.1 of the surface system description SKB-R--04-25, this report presents considerable additional features, especially in the ecosystem description (Chapter 4) and in the description of the surface hydrology (Section 3.4). A first attempt has also been made to connect the flow of matter (carbon) between the different ecosystems into an overall ecosystem model at a landscape level. A summarised version of this report is also presented in SKB-R--05-08 together with geological-, hydrogeological-, transport properties-, thermal properties-, rock mechanics- and hydrogeochemical descriptions.

  15. The effect of entrainment through atmospheric boundary layer growth on observed and modeled surface ozone in the Colorado Front Range

    Science.gov (United States)

    Kaser, L.; Patton, E. G.; Pfister, G. G.; Weinheimer, A. J.; Montzka, D. D.; Flocke, F.; Thompson, A. M.; Stauffer, R. M.; Halliday, H. S.

    2017-06-01

    Ozone concentrations at the Earth's surface are controlled by meteorological and chemical processes and are a function of advection, entrainment, deposition, and net chemical production/loss. The relative contributions of these processes vary in time and space. Understanding the relative importance of these processes controlling surface ozone concentrations is an essential component for designing effective regulatory strategies. Here we focus on the diurnal cycle of entrainment through atmospheric boundary layer (ABL) growth in the Colorado Front Range. Aircraft soundings and surface observations collected in July/August 2014 during the DISCOVER-AQ/FRAPPÉ (Deriving Information on Surface conditions from Column and Vertically Resolved Observations Relevant to Air Quality/Front Range Air Pollution and Photochemistry Éxperiment) campaigns and equivalent data simulated by a regional chemical transport model are analyzed. Entrainment through ABL growth is most important in the early morning, fumigating the surface at a rate of 5 ppbv/h. The fumigation effect weakens near noon and changes sign to become a small dilution effect in the afternoon on the order of -1 ppbv/h. The chemical transport model WRF-Chem (Weather Research and Forecasting Model with chemistry) underestimates ozone at all altitudes during this study on the order of 10-15 ppbv. The entrainment through ABL growth is overestimated by the model in the order of 0.6-0.8 ppbv/h. This results from differences in boundary layer growth in the morning and ozone concentration jump across the ABL top in the afternoon. This implicates stronger modeled fumigation in the morning and weaker modeled dilution after 11:00 LT.

  16. Closure Report for Corrective Action Unit 300: Surface Release Areas Nevada Test Site, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Restoration

    2007-07-01

    Corrective Action Unit (CAU) 300 is located in Areas 23, 25, and 26 of the Nevada Test Site, which is located approximately 65 miles northwest of Las Vegas, Nevada. CAU 300 is listed in the Federal Facility Agreement and Consent Order of 1996 as Surface Release Areas and is comprised of the following seven Corrective Action Sites (CASs), which are associated with the identified Building (Bldg): {sm_bullet} CAS 23-21-03, Bldg 750 Surface Discharge {sm_bullet} CAS 23-25-02, Bldg 750 Outfall {sm_bullet} CAS 23-25-03, Bldg 751 Outfall {sm_bullet} CAS 25-60-01, Bldg 3113A Outfall {sm_bullet} CAS 25-60-02, Bldg 3901 Outfall {sm_bullet} CAS 25-62-01, Bldg 3124 Contaminated Soil {sm_bullet} CAS 26-60-01, Bldg 2105 Outfall and Decon Pad The Nevada Division of Environmental Protection (NDEP)-approved corrective action alternative for CASs 23-21-03, 23-25-02, and 23-25-03 is no further action. As a best management practice, approximately 48 feet of metal piping was removed from CAS 23-25-02 and disposed of as sanitary waste. The NDEP-approved corrective action alternative for CASs 25-60-01, 25-60-02, 25-62-01, and 26-60-01, is clean closure. Closure activities for these CASs included removing and disposing of soil impacted with total petroleum hydrocarbons-diesel range organics (TPH-DRO), polychlorinated biphenyls (PCBs), semivolatile organic compounds (SVOCs), and cesium (Cs)-137, concrete impacted with TPH-DRO, and associated piping impacted with TPH-DRO. CAU 300 was closed in accordance with the NDEP-approved CAU 300 Corrective Action Plan (CAP) (U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office [NNSA/NSO], 2006). The closure activities specified in the CAP were based on the recommendations presented in the CAU 300 Corrective Action Decision Document (NNSA/NSO, 2005). This Closure Report documents CAU 300 closure activities. During closure activities, approximately 40 cubic yards (yd3) of low-level waste consisting of TPH-DRO-, PCB

  17. Evaporation and wetted area of single droplets on waxy and hairy leaf surfaces.

    Science.gov (United States)

    Zhu, H; Yu, Y; Ozkan, H E; Derksen, R C; Krause, C R

    2008-01-01

    Understanding the evaporation of pesticide droplets and wetting of Leaf surfaces can increase foliar application efficiency and reduce pesticide use. Evaporation time and wetted area of single pesticide droplets on hairy and waxy geranium leaf surfaces were measured under the controlled conditions for five droplet sizes and three relative humidities. The sprays used to form droplets included water, a nonionic colloidal polymer drift retardant, an alkyl polyoxyethylene surfactant, and an insecticide. Adding the surfactant into spray mixtures greatly increased droplet wetted area on the surfaces while droplet evaporation time was greatly reduced. Adding the drift retardant into spray mixture slightly increased the droplet evaporation time and the wetted area. Also, droplets had Longer evaporation times on waxy leaves than on hairy leaves for all droplet diameters and all relative humidity conditions. Increasing relative humidity could increase the droplet evaporation time greatly but did not change the the wetted area. The droplet evaporation time and wetted area increased exponentially as the droplet size increased. Therefore, droplet size, surface characteristics of the target, relative humidity, and chemical composition of the spray mixtures (water alone, pesticide, additives) should be included as important factors that affect the efficacy and efficiency of pesticide applications.

  18. Investigating the influence of long-range transport on surface O3 in Nevada, USA, using observations from multiple measurement platforms.

    Science.gov (United States)

    Fine, Rebekka; Miller, Matthieu B; Yates, Emma L; Iraci, Laura T; Gustin, Mae Sexauer

    2015-10-15

    The current United States (US) National Ambient Air Quality Standard (NAAQS) for O3 (75 ppb) is expected to be revised to between 60 and 70 ppb. As the NAAQS becomes more stringent, characterizing the extent of O3 and precursors transported into the US is increasingly important. Given the high elevation, complex terrain, and location in the Intermountain West, the State of Nevada is ideally situated to intercept air transported into the US. Until recently, measurements of O3 and associated pollutants were limited to areas in and around the cities of Las Vegas and Reno. In 2011, the Nevada Rural Ozone Initiative began and through this project 13 surface monitoring sites were established. Also in 2011, the NASA Ames Alpha Jet Atmospheric eXperiment (AJAX) began making routine aircraft measurements of O3 and other greenhouse gases in Nevada. The availability of aircraft and surface measurements in a relatively rural, remote setting in the Intermountain West presented a unique opportunity to investigate sources contributing to the O3 observed in Nevada. Our analyses indicate that stratosphere to troposphere transport, long-range transport of Asian pollution, and regional emissions from urban areas and wildfires influence surface observations. The complexity of sources identified here along with the fact that O3 frequently approaches the threshold being considered for a revised NAAQS indicate that interstate and international cooperation will be necessary to achieve compliance with a more stringent regulatory standard. Further, on a seasonal basis we found no significant difference between daily 1-h maximum O3 at surface sites, which ranged in elevation from 888 to 2307 m, and aircraft measurements of O3 O3 across rural Nevada and indicates that column measurements from Railroad Valley, NV are useful in understanding these processes. Copyright © 2015 Elsevier B.V. All rights reserved.

  19. Transparent self-cleaning lubricant-infused surfaces made with large-area breath figure patterns

    Science.gov (United States)

    Zhang, Pengfei; Chen, Huawei; Zhang, Liwen; Ran, Tong; Zhang, Deyuan

    2015-11-01

    Nepenthes pitcher inspired slippery lubricant-infused porous surfaces greatly impact the understanding of liquid-repellent surfaces construction and have attracted extensive attention in recent years due to their potential applications in self-cleaning, anti-fouling, anti-icing, etc. In this work, we have successfully fabricated transparent slippery lubricant-infused surfaces based on breath figure patterns (BFPs). Large-area BFPs with interconnected pores were initially formed on the glass substrate and then a suitable lubricant was added onto the surfaces. The interconnected pores in BFPs were able to hold the lubricant liquid in place and form a stable liquid/solid composite surface capable of repelling a variety of liquids. The liquid-repellent surfaces show extremely low critical sliding angles for various liquids, thus providing the surfaces with efficient self-cleaning property. It was also found that the liquid droplets' sliding behaviors on the surfaces were significantly influenced by the tilting angle of the substrate, liquid volume, liquid chemical properties, and pore sizes of the surfaces.

  20. Streamlined Approach for Environmental Restoration Plan for Corrective Action Unit 408: Bomblet Target Area, Tonopah Test Range, Nevada

    International Nuclear Information System (INIS)

    NSTec Environmental Management

    2006-01-01

    This Streamlined Approach for Environmental Restoration Plan provides the details for the closure of Corrective Action Unit (CAU) 408, Bomblet Target Area. CAU 408 is located at the Tonopah Test Range and is currently listed in Appendix III of the Federal Facility Agreement and Consent Order of 1996. One Corrective Action Site (CAS) is included in CAU 408: (lg b ullet) CAS TA-55-002-TAB2, Bomblet Target Areas Based on historical documentation, personnel interviews, process knowledge, site visits, aerial photography, multispectral data, preliminary geophysical surveys, and the results of data quality objectives process (Section 3.0), clean closure will be implemented for CAU 408. CAU 408 closure activities will consist of identification and clearance of bomblet target areas, identification and removal of depleted uranium (DU) fragments on South Antelope Lake, and collection of verification samples. Any soil containing contaminants at concentrations above the action levels will be excavated and transported to an appropriate disposal facility. Based on existing information, contaminants of potential concern at CAU 408 include explosives. In addition, at South Antelope Lake, bomblets containing DU were tested. None of these contaminants is expected to be present in the soil at concentrations above the action levels; however, this will be determined by radiological surveys and verification sample results. The corrective action investigation and closure activities have been planned to include data collection and hold points throughout the process. Hold points are designed to allow decision makers to review the existing data and decide which of the available options are most suitable. Hold points include the review of radiological, geophysical, and analytical data and field observations

  1. Identification of 18S ribosomal DNA genotype of Acanthamoeba from hot spring recreation areas in the central range, Taiwan

    Science.gov (United States)

    Hsu, Bing-Mu; Ma, Po-Hua; Liou, Tai-Sheng; Chen, Jung-Sheng; Shih, Feng-Cheng

    2009-04-01

    SummaryAcanthamoeba is a free-living amoebae ubiquitous to aquatic environments. Within the genus a few species are recognized as opportunistic potential human pathogens, which cause granulomatous amoebic encephalitis (GAE) and keratitis. Infections of keratitis are frequently reported through wearing lens while swimming in the non-disinfected aquatic environment. Contaminations in hot tubs, spas and public baths are also possible. As a result, in this study, we identified Acanthamoeba based on the PCR amplification with a genus-specific primer pair and investigated the distribution of Acanthamoeba at five hot spring recreation areas in central range, Taiwan. We gathered data on factors potentially associated with the pathogen's distribution, including various sampling sites, aquatic environment, physical and microbiological water quality parameters. Spring water was collected from 55 sites and Acanthamoeba was detected in 9 (16.4%). The most frequently detected was Acanthamoeba griffini, followed by Acanthamoeba jacobsi. Legionella were detected in 18 (32.7%) of the sites sampled in this study. The species of Legionella identified included Legionella pneumophila serotype 6, serotype 1, and Legionella erythra. Overall, 9.1% of the samples contained both Acanthamoeba and Legionella. The prevalence of Acanthamoeba was contrary to the levels of microbiological indicators recommended by Taiwan CDC, and no significant differences (Mann-Whitney U test, P Acanthamoeba and water quality parameters. Results of this survey confirm the existence of Acanthamoeba in Taiwan spring recreation areas. Acanthamoeba, the organism responsible for the majority of Acanthamoeba keratitis and can serve as vehicles for facultative pathogens, should be considered a potential threat for health associated with human activities in spring recreation areas of Taiwan.

  2. Long-Range Transhorizon Lunar Surface Radio Wave Propagation in the Presence of a Regolith and a Sparse Exospheric Plasma

    Science.gov (United States)

    Manning, Robert M.

    2008-01-01

    Long-range, over-the-horizon (transhorizon) radio wave propagation is considered for the case of the Moon. In the event that relay satellites are not available or otherwise unwarranted for use, transhorizon communication provides for a contingency or backup option for non line-of-sight lunar surface exploration scenarios. Two potential low-frequency propagation mechanisms characteristic of the lunar landscape are the lunar regolith and the photoelectron induced plasma exosphere enveloping the Moon. Although it was hoped that the regolith would provide for a spherical waveguide which could support a trapped surface wave phenomena, it is found that, in most cases, the regolith is deleterious to long range radio wave propagation. However, the presence of the plasma of the lunar exosphere supports wave propagation and, in fact, surpasses the attenuation of the regolith. Given the models of the regolith and exosphere adopted here, it is recommended that a frequency of 1 MHz be considered for low rate data transmission along the lunar surface. It is also recommended that further research be done to capture the descriptive physics of the regolith and the exospheric plasma so that a more complete model can be obtained. This comprehensive theoretical study is based entirely on first principles and the mathematical techniques needed are developed as required; it is self-contained and should not require the use of outside resources for its understanding.

  3. Atmospheric and surface water pollution interpretation in the Gdansk beltway impact range by the use of multivariate analysis

    Energy Technology Data Exchange (ETDEWEB)

    Dubiella-Jackowska, Aleksandra; Polkowska, Zaneta; Kudlak, Blazej; Namiesnik, Jacek [Chemical Faculty, Department of Analytical Chemistry, Gdansk University of Technology, Gdansk (Poland); Astel, Aleksander [Environmental Chemistry Research Unit, Institute of Biology and Environmental Protection, Pomeranian Academy, Slupsk (Poland); Staszek, Wojciech [Faculty of Physical Geography and Environmental Management, University of Gdansk, Gdansk (Poland)

    2010-09-15

    The present study deals with the application of the hierarchical cluster analysis and non-parametric tests in order to interpret the Gdansk Beltway impact range. The data set represents concentration values for major inorganic ions (Na{sup +}, NH{sub 4}{sup +}, K{sup +}, Mg{sup 2+}, Ca{sup 2+}, F{sup -}, Cl{sup -}, NO{sub 3}{sup -}, and SO{sub 4}{sup 2-}) as well as electrolytic conductivity and pH measured in various water samples [precipitation, throughfall water, road runoff, and surface water (drainage ditches, surface water reservoirs, and spring water)] collected in the vicinity of the beltway. Several similarity groups were discovered both in the objects and in the variables modes according to the water sample. In the majority of cases clear anthropogenic (fertilizers usage and transport, road salting in winter) and semi-natural (sea salt aerosols, erosion of construction materials) impacts were discovered. Spatial variation was discovered for road runoff samples and samples collected from surface water reservoirs and springs. Surprisingly no clear seasonal variability was discovered for precipitation chemistry, while some evidences for existing of summer and winter specific chemical profile was discovered for road runoff samples. In general, limited range of the Gdansk Beltway impact was proven. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  4. A wide area Bipolar Cascade Resonant Cavity Light Emitting Diode for a Hybrid Range-Intensity Sensor

    Science.gov (United States)

    Turner, Reginald J.

    Autonomous Ground Vehicles (AGV) will require high-speed, real-time three dimensional (3-D) image processing to navigate treacherous terrain in order to complete their assigned mission without a human in the loop. LIDAR scanners of the 3-D variety, provide the necessary area coverage for 3-D image processing, but lack the speed to deliver the collected data for real-time processing. A novel Hybrid Range-Intensity System (HRIS) has been proposed for imaging large swaths of area very rapidly. This system is comprised of two infrared cameras, an illumination source, a control and coordination system to position the cameras, and signal processing algorithms to extract the contour image of the scene. This dissertation focused on the development of an illuminator for the HRIS. This illuminator enables faster image rendering and reduces the potential of errors in return signal data, that could be generated from extremely rough terrain. Four major achievements resulted from this work, which advance the field of 3-D image acquisition. The first is that the TJ is an effective current spreading layer for LEDs with mesa width up to 140 mum and current densities of ˜ 1 x 106A/cm2. The TJ allows fabrication of an efficient illuminator, with required geometry for the HRIS to operate as a real-time 3-D imaging system. Secondly, a design for a Bipolar Cascade-Resonant Cavity Light Emitting Diode (BC-RCLED) has been accomplished, that will illuminate the FOV of the hybrid-ranged intensity system with a single sweep of the beam. This device is capable of producing ˜ 330 mW of output power. Additionally, from this work, key parameters for HRIS design were identified. Using a collection optic with a 15 cm diameter, an HRIS mounting height of 1.5 m, and a detector integration time of 330 msec, a SNR of 20 dB was achieved. Lastly, we demonstrated that the BC-RCLED designed for the HRIS can deliver sufficient energy to produce the required SNR. Also, through parametric analysis, we

  5. Body surface area in normal-weight, overweight, and obese adults. A comparison study.

    Science.gov (United States)

    Verbraecken, Johan; Van de Heyning, Paul; De Backer, Wilfried; Van Gaal, Luc

    2006-04-01

    Values for body surface area (BSA) are commonly used in medicine, particularly to calculate doses of chemotherapeutic agents and index cardiac output. Various BSA formulas have been developed over the years. The DuBois and DuBois (Arch Intern Med 1916;17:863-71) BSA equation is the most widely used, although derived from only 9 subjects. More recently, Mosteller (N Engl J Med 1987;317:1098) produced a simple formula, [weight (kg) x height (cm)/3600](1/2), which could be easily remembered and evaluated on a pocket calculator, but validation data in adults are rare. The purpose of the present study was to examine the BSA based on Mosteller's formula in normal-weight (body mass index [BMI], 20-24.9 kg/m(2)), overweight (BMI, 25-29.9 kg/m(2)), and obese (BMI, >/=30 kg/m(2)) adults (>18 years old) in comparison with other empirically derived formulas (DuBois and DuBois, Boyd [The growth of the surface area of the human body. Minneapolis: University of Minnesota Press; 1935], Gehan and George [Cancer Chemother Rep 1970;54:225-35], US Environmental Protection Agency [Development of statistical distributions or ranges of standard factors used in exposure assessments Washington, EPA/600/8-85-010. Office of Health and Environmental Assessment; 1985), Haycock et al [J Pediatr 1978;93:62-6], Mattar [Crit Care Med 1989;17:846-7], Livingston and Scott [Am J Physiol Endocrinol Metab 2001;281:E586-91]) and with the new 3-dimensional-derived formula of Yu et al (Appl Ergon. 2003;34:273-8). One thousand eight hundred sixty-eight patients were evaluated (397 normal weight [BMI, 23 +/- 1 kg/m(2); age, 50 +/- 14 years; M/F, 289/108], 714 overweight [BMI, 27 +/- 1 kg/m(2); age, 52 +/- 11 years; M/F, 594/120], and 757 obese [BMI, 36 +/- 6 kg/m(2); age, 53 +/- 11 years; M/F, 543/215]). The overall BSA was 2.04 +/- 0.24 m(2): 1.81 +/- 0.19 m(2) in normal-weight, 1.99 +/- 0.16 m(2) in overweight, and 2.21 +/- 0.22 m(2) in obese subjects. These values were significantly higher in overweight

  6. Surface area and the seabed area, volume, depth, slope, and topographic variation for the world's seas, oceans, and countries.

    Science.gov (United States)

    Costello, Mark John; Cheung, Alan; De Hauwere, Nathalie

    2010-12-01

    Depth and topography directly and indirectly influence most ocean environmental conditions, including light penetration and photosynthesis, sedimentation, current movements and stratification, and thus temperature and oxygen gradients. These parameters are thus likely to influence species distribution patterns and productivity in the oceans. They may be considered the foundation for any standardized classification of ocean ecosystems and important correlates of metrics of biodiversity (e.g., species richness and composition, fisheries). While statistics on ocean depth and topography are often quoted, how they were derived is rarely cited, and unless calculated using the same spatial resolution the resulting statistics will not be strictly comparable. We provide such statistics using the best available resolution (1-min) global bathymetry, and open source digital maps of the world's seas and oceans and countries' Exclusive Economic Zones, using a standardized methodology. We created a terrain map and calculated sea surface and seabed area, volume, and mean, standard deviation, maximum, and minimum, of both depth and slope. All the source data and our database are freely available online. We found that although the ocean is flat, and up to 71% of the area has a ocean volume exceeds 1.3 billion km(3) (or 1.3 sextillion liters), and sea surface and seabed areas over 354 million km(2). We propose the coefficient of variation of slope as an index of topographic heterogeneity. Future studies may improve on this database, for example by using a more detailed bathymetry, and in situ measured data. The database could be used to classify ocean features, such as abyssal plains, ridges, and slopes, and thus provide the basis for a standards based classification of ocean topography.

  7. Performance improvement of long-range surface plasmon structure for use in an all-optical switch

    Science.gov (United States)

    Jandaghian, Ali; Lotfalian, Ali; Kouhkan, Mohsen; Mohajerani, Ezeddin

    2017-12-01

    This paper presents important parameters in performance of long-range surface plasmon (LRSP) structure (SF4/PVA/silver/PMMA-DR1) that are improved. We select poly(vinyl alcohol) (PVA) as the first dielectric layer due to its water solubility and good optical properties. The thickness of PVA and silver layers is optimized by transfer matrix method based on Fresnel equations. Surface morphologies of PVA and silver surfaces are analyzed by AFM imaging due to their important role in the performance of an LRSP structure. Furthermore, the sensitivity of an all-optical switch based on plasmon is investigated. In order to compare the sensitivity of LRSP and conventional surface plasmon (SP) structures in switching mode, full wide of half maximum, resonance angles, and pump powers of both structures are measured by a custom-made optical setup based on angular interrogation with a precision of 0.01 deg. Finally, we conclude that for creating equal signal levels in both samples, the required pump power for LRSP structure was about three times less than that for conventional SP; thus, these results led to power savings in optical switches.

  8. Corrective Action Investigation Plan for Corrective Action Unit 428: Area 3 Septic Waste Systems 1 and 5, Tonopah Test Range, Nevada, REVISION 0, march 1999

    Energy Technology Data Exchange (ETDEWEB)

    DOE/NV

    1999-03-26

    and Recovery Act characteristic volatile organic compounds, semivolatile organic compounds, and metals. A limited number of samples will be analyzed for gamma- emitting radionuclides and isotopic uranium from four of the septic tanks and if radiological field screening levels are exceeded. Additional samples will be analyzed for geotechnical and hydrological properties and a bioassessment may be performed. The technical approach for investigating this Corrective Action Unit consists of the following activities: (1) Perform video surveys of the discharge and outfall lines. (2) Collect samples of material in the septic tanks. (3) Conduct exploratory trenching to locate and inspect subsurface components. (4) Collect subsurface soil samples in areas of the collection system including the septic tanks and outfall end of distribution boxes. (5) Collect subsurface soil samples underlying the leachfield distribution pipes via trenching. (6) Collect surface and near- surface samples near potential locations of the Acid Sewer Outfall if Septic Waste System 5 Leachfield cannot be located. (7) Field screen samples for volatile organic compounds, total petroleum hydrocarbons, and radiological activity. (8) Drill boreholes and collect subsurface soil samples if required. (9) Analyze samples for total volatile organic compounds, total semivolatile organic compounds, total Resource Conservation and Recovery Act metals, and total petroleum hydrocarbons (oil/ diesel range organics). Limited number of samples will be analyzed for gamma- emitting radionuclides and isotopic uranium from particular septic tanks and if radiological field screening levels are exceeded. (10) Collect samples from native soils beneath the distribution system and analyze for geotechnical/ hydrologic parameters. (11) Collect and analyze bioassessment samples at the discretion of the Site Supervisor if total petroleum hydrocarbons exceed field- screening levels.

  9. Corrective Action Investigation Plan for Corrective Action Unit 428: Area 3 Septic Waste Systems 1 and 5, Tonopah Test Range, Nevada

    International Nuclear Information System (INIS)

    ITLV

    1999-01-01

    and Recovery Act characteristic volatile organic compounds, semivolatile organic compounds, and metals. A limited number of samples will be analyzed for gamma- emitting radionuclides and isotopic uranium from four of the septic tanks and if radiological field screening levels are exceeded. Additional samples will be analyzed for geotechnical and hydrological properties and a bioassessment may be performed. The technical approach for investigating this Corrective Action Unit consists of the following activities: Perform video surveys of the discharge and outfall lines. Collect samples of material in the septic tanks. Conduct exploratory trenching to locate and inspect subsurface components. Collect subsurface soil samples in areas of the collection system including the septic tanks and outfall end of distribution boxes. Collect subsurface soil samples underlying the leachfield distribution pipes via trenching. Collect surface and near- surface samples near potential locations of the Acid Sewer Outfall if Septic Waste System 5 Leachfield cannot be located. Field screen samples for volatile organic compounds, total petroleum hydrocarbons, and radiological activity. Drill boreholes and collect subsurface soil samples if required. Analyze samples for total volatile organic compounds, total semivolatile organic compounds, total Resource Conservation and Recovery Act metals, and total petroleum hydrocarbons (oil/ diesel range organics). Limited number of samples will be analyzed for gamma- emitting radionuclides and isotopic uranium from particular septic tanks and if radiological field screening levels are exceeded. Collect samples from native soils beneath the distribution system and analyze for geotechnical/ hydrologic parameters. Collect and analyze bioassessment samples at the discretion of the Site Supervisor if total petroleum hydrocarbons exceed field- screening levels

  10. Synthesis of cerium oxide (CeO2) with high surface area through microwave assisted hydrothermal method

    International Nuclear Information System (INIS)

    Oliveira, M.J.C. de; Neiva, L.S.; Gama, L.; Oliveira, J.B.

    2011-01-01

    The objective of this research is synthesize nanoparticles with high surface area of Ceria (CeO 2 ) catalyst by a microwave hydrothermal method. For that it was used a 5% concentration in weight of [Ce(NO 3 ) 3. 6H 2 O] and 10 mL of [NaOH (5M)] under processing conditions in the equipment: maximum temperature of 150 deg C for 60 min with heating rate of 15 C /min. The resulting sample was characterized by XRD, SEM and BET method. It was observed that the Ceria particles are presented spatially in cubic structure, with crystallite size of 10 nm and surface area of 112 m²/g. Through the pore size distribution it was possible to observe that these were in mesoporous size, ranging from 3 to 30 nm. The possibility of obtaining catalysts with nanometer scale and high surface area by beans of microwave hydrothermal method, which involves low energy (low temperatures) and short synthesis time, makes this method very interesting and promising. (author)

  11. Tear-Film Evaporation Rate from Simultaneous Ocular-Surface Temperature and Tear-Breakup Area.

    Science.gov (United States)

    Dursch, Thomas J; Li, Wing; Taraz, Baseem; Lin, Meng C; Radke, Clayton J

    2018-01-01

    A corneal heat-transfer model is presented to quantify simultaneous measurements of fluorescein tear-breakup area (TBA) and ocular-surface temperature (OST). By accounting for disruption of the tear-film lipid layer (TFLL), we report evaporation rates through lipid-covered tear. The modified heat-transfer model provides new insights into evaporative dry eye. A quantitative analysis is presented to assess human aqueous tear evaporation rate (TER) through intact TFLLs from simultaneous in vivo measurement of time-dependent infrared OST and fluorescein TBA. We interpret simultaneous OST and TBA measurements using an extended heat-transfer model. We hypothesize that TBAs are ineffectively insulated by the TFLL and therefore exhibit higher TER than does that for a well-insulting TFLL-covered tear. As time proceeds, TBAs increase in number and size, thereby increasing the cornea area-averaged TER and decreasing OST. Tear-breakup areas were assessed from image analysis of fluorescein tear-film-breakup video recordings and are included in the heat-transfer description of OST. Model-predicted OSTs agree well with clinical experiments. Percent reductions in TER of lipid-covered tear range from 50 to 95% of that for pure water, in good agreement with literature. The physical picture of noninsulating or ruptured TFLL spots followed by enhanced evaporation from underlying cooler tear-film ruptures is consistent with the evaporative-driven mechanism for local tear rupture. A quantitative analysis is presented of in vivo TER from simultaneous clinical measurement of transient OST and TBA. The new heat-transfer model accounts for increased TER through expanding TBAs. Tear evaporation rate varies strongly across the cornea because lipid is effectively missing over tear-rupture troughs. The result is local faster evaporation compared with nonruptured, thick lipid-covered tear. Evaporative-driven tear-film ruptures deepen to a thickness where fluorescein quenching commences and local

  12. Snow specific surface area simulation using the one-layer snow model in the Canadian LAnd Surface Scheme (CLASS

    Directory of Open Access Journals (Sweden)

    A. Roy

    2013-06-01

    Full Text Available Snow grain size is a key parameter for modeling microwave snow emission properties and the surface energy balance because of its influence on the snow albedo, thermal conductivity and diffusivity. A model of the specific surface area (SSA of snow was implemented in the one-layer snow model in the Canadian LAnd Surface Scheme (CLASS version 3.4. This offline multilayer model (CLASS-SSA simulates the decrease of SSA based on snow age, snow temperature and the temperature gradient under dry snow conditions, while it considers the liquid water content of the snowpack for wet snow metamorphism. We compare the model with ground-based measurements from several sites (alpine, arctic and subarctic with different types of snow. The model provides simulated SSA in good agreement with measurements with an overall point-to-point comparison RMSE of 8.0 m2 kg–1, and a root mean square error (RMSE of 5.1 m2 kg–1 for the snowpack average SSA. The model, however, is limited under wet conditions due to the single-layer nature of the CLASS model, leading to a single liquid water content value for the whole snowpack. The SSA simulations are of great interest for satellite passive microwave brightness temperature assimilations, snow mass balance retrievals and surface energy balance calculations with associated climate feedbacks.

  13. Impact of microstructure evolution on the difference between geometric and reactive surface areas in natural chalk

    Science.gov (United States)

    Yang, Y.; Bruns, S.; Stipp, S. L. S.; Sørensen, H. O.

    2018-05-01

    The coupling between flow and mineral dissolution drives the evolution of many natural and engineered flow systems. Pore surface changes as microstructure evolves but this transient behaviour has traditionally been difficult to model. We combined a reactor network model with experimental, greyscale tomography data to establish the morphological grounds for differences among geometric, reactive and apparent surface areas in dissolving chalk. This approach allowed us to study the effects of initial geometry and macroscopic flow rate independently. The simulations showed that geometric surface, which represents a form of local transport heterogeneity, increases in an imposed flow field, even when the porous structure is chemically homogeneous. Hence, the fluid-reaction coupling leads to solid channelisation, which further results in fluid focusing and an increase in geometric surface area. Fluid focusing decreases the area of reactive surface and the residence time of reactant, both contribute to the over-normalisation of reaction rate. In addition, the growing and merging of microchannels, near the fluid entrance, contribute to the macroscopic, fast initial dissolution rate of rocks.

  14. Changes in thickness and surface area of the human cortex and their relationship with intelligence.

    Science.gov (United States)

    Schnack, Hugo G; van Haren, Neeltje E M; Brouwer, Rachel M; Evans, Alan; Durston, Sarah; Boomsma, Dorret I; Kahn, René S; Hulshoff Pol, Hilleke E

    2015-06-01

    Changes in cortical thickness over time have been related to intelligence, but whether changes in cortical surface area are related to general cognitive functioning is unknown. We therefore examined the relationship between intelligence quotient (IQ) and changes in cortical thickness and surface over time in 504 healthy subjects. At 10 years of age, more intelligent children have a slightly thinner cortex than children with a lower IQ. This relationship becomes more pronounced with increasing age: with higher IQ, a faster thinning of the cortex is found over time. In the more intelligent young adults, this relationship reverses so that by the age of 42 a thicker cortex is associated with higher intelligence. In contrast, cortical surface is larger in more intelligent children at the age of 10. The cortical surface is still expanding, reaching its maximum area during adolescence. With higher IQ, cortical expansion is completed at a younger age; and once completed, surface area decreases at a higher rate. These findings suggest that intelligence may be more related to the magnitude and timing of changes in brain structure during development than to brain structure per se, and that the cortex is never completed but shows continuing intelligence-dependent development. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

  15. Ambient pressure dried tetrapropoxysilane-based silica aerogels with high specific surface area

    Science.gov (United States)

    Parale, Vinayak G.; Han, Wooje; Jung, Hae-Noo-Ree; Lee, Kyu-Yeon; Park, Hyung-Ho

    2018-01-01

    In the present paper, we report the synthesis of tetrapropoxysilane (TPOS)-based silica aerogels with high surface area and large pore volume. The silica aerogels were prepared by a two-step sol-gel process followed by surface modification via a simple ambient pressure drying approach. In order to minimize drying shrinkage and obtain hydrophobic aerogels, the surface of the alcogels was modified using trichloromethylsilane as a silylating agent. The effect of the sol-gel compositional parameters on the polymerization of aerogels prepared by TPOS, one of the precursors belonging to the Si(OR)4 family, was reported for the first time. The oxalic acid and NH4OH concentrations were adjusted to achieve good-quality aerogels with high surface area, low density, and high transparency. Controlling the hydrolysis and condensation reactions of the TPOS precursor turned out to be the most important factor to determine the pore characteristics of the aerogel. Highly transparent aerogels with high specific surface area (938 m2/g) and low density (0.047 g/cm3) could be obtained using an optimized TPOS/MeOH molar ratio with appropriate concentrations of oxalic acid and NH4OH.

  16. Quality of surface-water supplies in the Triangle area of North Carolina, water year 2008

    Science.gov (United States)

    Giorgino, M.J.; Rasmussen, R.B.; Pfeifle, C.A.

    2012-01-01

    Surface-water supplies are important sources of drinking water for residents in the Triangle area of North Carolina, which is located within the upper Cape Fear and Neuse River Basins. Since 1988, the U.S. Geological Survey and a consortium of governments have tracked water-quality conditions and trends in several of the area's water-supply lakes and streams. This report summarizes data collected through this cooperative effort, known as the Triangle Area Water Supply Monitoring Project, during October 2007 through September 2008. Major findings for this period include:

  17. Minimal area surfaces dual to Wilson loops and the Mathieu equation

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Changyu; He, Yifei; Kruczenski, Martin [Department of Physics and Astronomy, Purdue University, 525 Northwestern Avenue, W. Lafayette, IN, 47907-2036 (United States)

    2016-08-11

    The AdS/CFT correspondence relates Wilson loops in N=4 SYM to minimal area surfaces in AdS{sub 5}×S{sup 5} space. Recently, a new approach to study minimal area surfaces in AdS{sub 3}⊂AdS{sub 5} was discussed based on a Schroedinger equation with a periodic potential determined by the Schwarzian derivative of the shape of the Wilson loop. Here we use the Mathieu equation, a standard example of a periodic potential, to obtain a class of Wilson loops such that the area of the dual minimal area surface can be computed analytically in terms of eigenvalues of such equation. As opposed to previous examples, these minimal surfaces have an umbilical point (where the principal curvatures are equal) and are invariant under λ-deformations. In various limits they reduce to the single and multiple wound circular Wilson loop and to the regular light-like polygons studied by Alday and Maldacena. In this last limit, the periodic potential becomes a series of deep wells each related to a light-like segment. Small corrections are described by a tight-binding approximation. In the circular limit they are well approximated by an expansion developed by A. Dekel. In the particular case of no umbilical points they reduce to a previous solution proposed by J. Toledo. The construction works both in Euclidean and Minkowski signature of AdS{sub 3}.

  18. Minimal area surfaces dual to Wilson loops and the Mathieu equation

    Science.gov (United States)

    Huang, Changyu; He, Yifei; Kruczenski, Martin

    2016-08-01

    The AdS/CFT correspondence relates Wilson loops in {N}=4 SYM to minimal area surfaces in AdS 5 × S 5 space. Recently, a new approach to study minimal area surfaces in AdS 3 ⊂ AdS 5 was discussed based on a Schroedinger equation with a periodic potential determined by the Schwarzian derivative of the shape of the Wilson loop. Here we use the Mathieu equation, a standard example of a periodic potential, to obtain a class of Wilson loops such that the area of the dual minimal area surface can be computed analytically in terms of eigenvalues of such equation. As opposed to previous examples, these minimal surfaces have an umbilical point (where the principal curvatures are equal) and are invariant under λ-deformations. In various limits they reduce to the single and multiple wound circular Wilson loop and to the regular light-like polygons studied by Alday and Maldacena. In this last limit, the periodic potential becomes a series of deep wells each related to a light-like segment. Small corrections are described by a tight-binding approximation. In the circular limit they are well approximated by an expansion developed by A. Dekel. In the particular case of no umbilical points they reduce to a previous solution proposed by J. Toledo. The construction works both in Euclidean and Minkowski signature of AdS 3.

  19. Lp-dual affine surface area forms of Busemann–Petty type problems

    Indian Academy of Sciences (India)

    (Math. Sci.) Vol. 125, No. 1, February 2015, pp. 71–77. c Indian Academy of Sciences. Lp-dual affine surface area forms of Busemann–Petty type problems ..... problem in three dimensions,. Ann. Math. 140(2) (1994) 435–447. [4] Gardner R J, Geometric tomography, 2nd edn (2006) (Cambridge, UK: Cambridge Univ. Press).

  20. Specific surface area behavior of a dissolving population of particles. Augmenting Mercer Dissolution Theory

    International Nuclear Information System (INIS)

    Scripsick, R.C.; Rothenberg, S.J.

    1986-01-01

    Specific surface area (Sp) measurements were made on two uranium oxide aerosol materials before and after in vitro dissolution studies were performed on the materials. The results of these Sp measurements were evaluated relative to predictions made from extending Mercer dissolution theory to describe the Sp behavior of a dissolving population of particles

  1. Periodic Mesoporous Organosilica Nanocubes with Ultrahigh Surface Areas for Efficient CO2 Adsorption

    Science.gov (United States)

    Wei, Yong; Li, Xiaomin; Zhang, Renyuan; Liu, Yong; Wang, Wenxing; Ling, Yun; El-Toni, Ahmed Mohamed; Zhao, Dongyuan

    2016-02-01

    Ultrahigh surface area single-crystals of periodic mesoporous organosilica (PMOs) with uniform cubic or truncated-cubic morphology and organic/inorganic components homogeneously distributed over the whole frameworks have successfully been prepared by a sol-gel surfactant-templating method. By tuning the porous feature and polymerization degree, the surface areas of the obtained PMO nanocubes can reach as high as 2370 m2/g, which is the highest for silica-based mesoporous materials. The ultrahigh surface area of the obtained PMO single crystals is mainly resulted from abundant micropores in the mesoporous frameworks. Furthermore, the diameter of the nanocubes can also be well controlled from 150 to 600 nm. The materials show ultrahigh CO2 adsorption capacity (up to 1.42 mmol/g at 273 K) which is much higher than other porous silica materials and comparable to some carbonaceous materials. The adsorption of CO2 into the PMO nanocubes is mainly in physical interaction, therefore the adsorption-desorption process is highly reversible and the adsorption capacity is much dependent on the surface area of the materials. Moreover, the selectivity is also very high (~11 times to N2) towards CO2 adsorption.

  2. Area densitometry using rotating Scheimpflug photography for posterior capsule opacification and surface light scattering analyses.

    Science.gov (United States)

    Minami, Keiichiro; Honbo, Masato; Mori, Yosai; Kataoka, Yasushi; Miyata, Kazunori

    2015-11-01

    To compare area densitometry analysis using rotating Scheimpflug photography in quantifications of posterior capsule opacification (PCO) and surface light scattering with previous anterior-segment analyzer measurement. Miyata Eye Hospital, Miyazaki, Japan. Prospective observational case series. Scheimpflug images of eyes with foldable intraocular lenses (IOLs) were obtained using rotating and fixed Scheimpflug photography. Area densitometry on the posterior and anterior surfaces was conducted for PCO and surface light scattering analyses, respectively, with an identical area size. Correlation between two measurements was analyzed using linear regression. The study included 105 eyes of 74 patients who received IOLs 1 to 18 years (mean, 4.9 ± 4.5 years) postoperatively. In the PCO analysis on the posterior IOL surface, there was a significant correlation between the two measurements (P photography exhibited saturation due to intensive scatterings. Area densitometry combined with a rotating Scheimpflug photography was exchangeable to previously established densitometry measurement, and allowed successive evaluation in longer-term observations. Copyright © 2015 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

  3. Characterization of pigment-leached antifouling coatings using BET surface area measurements and mercury porosimetry

    DEFF Research Database (Denmark)

    Kiil, Søren; Dam-Johansen, Kim

    2007-01-01

    In this work BET surface area measurements and mercury porosimetry are used to characterize leached layers formed when seawater-soluble pigments (Cu2O and ZnO) dissolve during accelerated leaching of simple antifouling coatings. Measurements on single-pigment coatings show that an increasing...

  4. Surface area of lactose and lactose granulates on consolidation and compaction

    NARCIS (Netherlands)

    Riepma, Klaas Alouis

    1993-01-01

    This dissertation discusses the effect of short time storage at different conditions on the strength and the specific BET surface area of lactose tablets. In addition, some aspects are studied of the consolidation and compaction properties of crystalline lactose fractions in heterogeneous systems.

  5. High surface area carbon for bifunctional air electrodes applied in zinc-air batteries

    Energy Technology Data Exchange (ETDEWEB)

    Arai, H. [on leave from NTT Laboratories (Japan); Mueller, S.; Haas, O. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    Bifunctional air electrodes with high surface area carbon substrates showed low reduction overpotential, thus are promising for enhancing the energy efficiency and power capability of zinc-air batteries. The improved performance is attributed to lower overpotential due to diffusion of the reaction intermediate, namely the peroxide ion. (author) 1 fig., 2 refs.

  6. A method for increasing the surface area of perovskite-type oxides

    Indian Academy of Sciences (India)

    combustion of methane at different temperatures (450–600oC) has been thoroughly investigated. The hydrothermal treatments result in the activation of the perovskite oxides by increasing their surface area very markedly. Keywords. ABO3-type perovskite oxides; LaCoO3; LaMnO3; hydrothermal treatment; catalytic ...

  7. Should blood flow during cardiopulmonary bypass be individualized more than to body surface area?

    DEFF Research Database (Denmark)

    Thomassen, Sisse Anette; Larsson, A; Andreasen, Jan Jesper

    Blood flow during cardiopulmonary bypass (CPB) is calculated on body surface area (BSA). Increasing comorbidity, age and weight of today's cardiac patients question this calculation as it may not reflect individual metabolic requirement. The hypothesis was that a measured cardiac index (CI) prior...... not improve cerebral and systemic oxygenation compared to a blood flow based on BSA....

  8. Mapping surface flow in low gradient areas with thermal remote sensing

    DEFF Research Database (Denmark)

    Prinds, Christian; Petersen, Rasmus Jes; Greve, Mogens Humlekrog

    Thermal infrared (TIR) imagery has long been used for mapping groundwater-surface water interactions and mainly for locating areas of groundwater seepage in lakes and shorelines (Rundquist et al. 1985, Banks et al. 1996). In this study, we used the method for locating discharge from tile drains...

  9. A method for increasing the surface area of perovskite-type oxides

    Indian Academy of Sciences (India)

    700oC (v), 800oC ( ) and without water treatment (U). The increase in the surface area of the perovskite-type oxides and the observed decrease in the crystal size by the steam treatment at 350–800oC are expected because of the recrystallization during the high temperature hydrothermal treatment depending upon the.

  10. Amylolytic hydrolysis of native starch granules affected by granule surface area.

    Science.gov (United States)

    Kim, J C; Kong, B W; Kim, M J; Lee, S H

    2008-11-01

    Initial stage of hydrolysis of native starch granules with various amylolytic enzymes, alpha-amylase from Bacillus subtilis, glucoamylase I (GA-I) and II (GA-II) from Aspergillus niger, and beta-amylase from sweet potato showed that the reaction was apparently affected by a specific surface area of the starch granules. The ratios of the reciprocal of initial velocity of each amylolytic hydrolysis for native potato and maize starch to that for rice with the amylolytic enzymes were nearly equivalent to the ratio of surface area per mass of the 2 starch granules to that of rice, that is, 6.94 and 2.25, respectively. Thus, the reciprocal of initial velocity of each enzymatic hydrolysis as expressed in a Lineweaver-Burk plot was a linear function of the reciprocal of surface area for each starch granule. As a result, it is concluded that amylolytic hydrolysis of native starch granules is governed by the specific surface area, not by the mass concentration, of each granule.

  11. Specific surface area effect on adsorption of chlorpyrifos and TCP by soils and modeling

    Science.gov (United States)

    The adsorption of chlorpyrifos and TCP (3,5,6, trichloro-2-pyridinol) was determined in four soils (Mollisol, Inceptisol, Entisol, Alfisol) having different specific surface areas (19–84 m2/g) but rather similar organic matter content (2.4–3.5%). Adsorption isotherms were derived from batch equilibr...

  12. Preparation of MgO Catalytic Support in Shaped Mesoporous High Surface Area Form

    Czech Academy of Sciences Publication Activity Database

    Gulková, Daniela; Šolcová, Olga; Zdražil, Miroslav

    2004-01-01

    Roč. 76, 1-3 (2004), s. 137-149 ISSN 1387-1811 R&D Projects: GA AV ČR IAA4072306 Institutional research plan: CEZ:AV0Z4072921 Keywords : MgO support * sigh Surface area * texture Subject RIV: CC - Organic Chemistry Impact factor: 2.093, year: 2004

  13. Thermal stability of porous sol-gel phosphosilicates and their surface area stabilisation by lanthanum addition

    NARCIS (Netherlands)

    Falco, Lorena; De Mendonca, Mariana Van Den Tempel; Mercadal, Juan J.; Zarubina, Valeriya; Melián-Cabrera, Ignacio

    2016-01-01

    The thermal stability of porous sol-gel phosphosilicates was studied by comparing the textural features upon calcination between 400 and 550 °C. A significant loss of surface area and pore volume were observed; the first is due to thermal coarsening of the nanoparticles, and the pore volume

  14. Allometric relationships for surface area and dry mass of young Norway spruce aboveground organs

    Czech Academy of Sciences Publication Activity Database

    Pokorný, Radek; Tomášková, Ivana

    53 2007, č. 12 (2007), s. 548-554 ISSN 1212-4834 R&D Projects: GA MŽP(CZ) SP/2D1/93/07 Institutional research plan: CEZ:AV0Z60870520 Keywords : allometry * biomass, * Picea abies * sapwood * surface area Subject RIV: GK - Forestry

  15. Estimating the surface area of non-convex particles from central planar sections

    DEFF Research Database (Denmark)

    Thórisdóttir, Ólöf; H.Rafati, Ali; Kiderlen, Markus

    . The Morse type estimator is well suited for computer assisted confocal microscopy and we demonstrate its practicability in a biological application: the surface area estimation of the nuclei of giant-cell glioblastoma from microscopy images. We also present an interactive software that allows the user...

  16. Flow analysis of water-powder mixtures: Application to specific surface area and shape factor

    NARCIS (Netherlands)

    Hunger, Martin; Brouwers, Jos

    2009-01-01

    This paper addresses the characterization of powder materials with respect to their application in concrete. Given that powders provide by far highest percentage of specific surface area in a concrete mix, their packing behavior and water demand is of vital interest for the design of concrete. They

  17. Turbostratic boron nitride coated on high-surface area metal oxide templates

    DEFF Research Database (Denmark)

    Klitgaard, Søren Kegnæs; Egeblad, Kresten; Brorson, M.

    2007-01-01

    Boron nitride coatings on high-surface area MgAl2O4 and Al2O3 have been synthesized and characterized by transmission electron microscopy and by X-ray powder diffraction. The metal oxide templates were coated with boron nitride using a simple nitridation in a flow of ammonia starting from ammonium...

  18. Condensation-Enhanced Self-Assembly as a Route to High Surface Area alpha-Aluminas

    NARCIS (Netherlands)

    Perez, Lidia Lopez; Zarubina, Valeriya; Heeres, Hero Jan; Melian-Cabrera, Ignacio

    2013-01-01

    High surface area nanosized alpha-alumina has been obtained by thermally treating a sol-gel-derived mesophase at 1200 degrees C; the mesophase was synthesized by a sol-gel route involving evaporation induced self-assembly (EISA) of a hydrolyzed gel from Al-tri-sec-butoxide in s-BuOH in the presence

  19. Escaping the correction for body surface area when calculating glomerular filtration rate in children

    Energy Technology Data Exchange (ETDEWEB)

    Piepsz, Amy; Tondeur, Marianne [CHU St. Pierre, Department of Radioisotopes, Brussels (Belgium); Ham, Hamphrey [University Hospital Ghent, Department of Nuclear Medicine, Ghent (Belgium)

    2008-09-15

    {sup 51}Cr ethylene diamine tetraacetic acid ({sup 51}Cr EDTA) clearance is nowadays considered as an accurate and reproducible method for measuring glomerular filtration rate (GFR) in children. Normal values in function of age, corrected for body surface area, have been recently updated. However, much criticism has been expressed about the validity of body surface area correction. The aim of the present paper was to present the normal GFR values, not corrected for body surface area, with the associated percentile curves. For that purpose, the same patients as in the previous paper were selected, namely those with no recent urinary tract infection, having a normal left to right {sup 99m}Tc MAG3 uptake ratio and a normal kidney morphology on the early parenchymal images. A single blood sample method was used for {sup 51}Cr EDTA clearance measurement. Clearance values, not corrected for body surface area, increased progressively up to the adolescence. The percentile curves were determined and allow, for a single patient, to estimate accurately the level of non-corrected clearance and the evolution with time, whatever the age. (orig.)

  20. Uncovering surface area and micropores in almond shell biochars by rainwater wash

    Science.gov (United States)

    Biochars have been considered for adsorption of contaminants in soil and water, as well as conditioning and improving soil quality. One important property of the biochar is surface area in the pores of the biochar. Biochars were created from almond shells from two almond varieties with different ash...

  1. Surface water and groundwater interaction in selected areas of Indus basin

    International Nuclear Information System (INIS)

    Akram, W.; Ahmad, M.; Tariq, J.A.; Latif, Z.; Malik, M.R.

    2011-08-01

    Isotope hydrological investigations were carried out in Marala-Khanki Area of Punjab for elucidating various aspects of surface water and groundwater interaction. Groundwater samples were collected on seasonal basis (low and high river discharge periods) while surface water (Chenab River) samples were collected more frequently (weekly or monthly basis). Isotopic data suggested that there is no significant contribution of surface water to groundwater recharge in Marala-Khanki Area and rain is the prevailing source of groundwater recharge. The data further revealed that isotopic values of Tarbala lake are higher than those of main lake. Indus river meaning that there is significant contribution of base flow in this pocket. Isotopic data of Indus river showed an increase at Tunsa as compared to Chashma in flow period indicating the high contribution of base flow at this point in time. Stable isotopes were successfully used to quantify the base flow contribution. (author)

  2. A Three-Dimensional Enormous Surface Area Aluminum Microneedle Array with Nanoporous Structure

    Directory of Open Access Journals (Sweden)

    Po Chun Chen

    2013-01-01

    Full Text Available We proposed fabricating an aluminum microneedle array with a nanochannel structure on the surface by combining micromachining, electrolyte polishing, and anodization methods. The microneedle array provides a three-dimensional (3D structure that possesses several hundred times more surface area than a traditional nanochannel template. Therefore, the microneedle array can potentially be used in many technology applications. This 3D microneedle array device can not only be used for painless injection or extraction, but also for storage, highly sensitive detection, drug delivery, and microelectrodes. From the calculation we made, the microneedle array not only increases surface area, but also enlarges the capacity of the device. Therefore, the microneedle array can further be used on many detecting, storing, or drug delivering applications.

  3. A Three-Dimensional Enormous Surface Area Aluminum Microneedle Array with Nanoporous Structure

    International Nuclear Information System (INIS)

    Chen, P.Ch.; Zou, J.; Hsieh, Sh.J.; Chen, Ch.Ch.

    2013-01-01

    We proposed fabricating an aluminum micro needle array with a nano channel structure on the surface by combining micromachining, electrolyte polishing, and anodization methods. The micro needle array provides a three-dimensional (3D) structure that possesses several hundred times more surface area than a traditional nano channel template. Therefore, the micro needle array can potentially be used in many technology applications. This 3D micro needle array device can not only be used for painless injection or extraction, but also for storage, highly sensitive detection, drug delivery, and microelectrodes. From the calculation we made, the micro needle array not only increases surface area, but also enlarges the capacity of the device. Therefore, the micro needle array can further be used on many detecting, storing, or drug delivering applications.

  4. Seeded on-surface supramolecular growth for large area conductive donor-acceptor assembly.

    Science.gov (United States)

    Goudappagouda; Chithiravel, Sundaresan; Krishnamoorthy, Kothandam; Gosavi, Suresh W; Babu, Sukumaran Santhosh

    2015-07-04

    Charge transport features of organic semiconductor assemblies are of paramount importance. However, large-area extended supramolecular structures of donor-acceptor combinations with controlled self-assembly pathways are hardly accessible. In this context, as a representative example, seeded on-surface supramolecular growth of tetrathiafulvalene and tetracyano-p-quinodimethane (TTF-TCNQ) using active termini of solution-formed sheaves has been introduced to form an extended assembly. We demonstrate for the first time, the creation of a large-area donor-acceptor assembly on the surface, which is practically very tedious, using a seeded, evaporation-assisted growth process. The excellent molecular ordering in this assembly is substantiated by its good electrical conductivity (~10⁻² S cm⁻¹). The on-surface assembly via both internally formed and externally added sheaf-like seeds open new pathways in supramolecular chemistry and device applications.

  5. Investigation on large-area fabrication of vivid shark skin with superior surface functions

    Science.gov (United States)

    Chen, Huawei; Zhang, Xin; Ma, Lingxi; Che, Da; Zhang, Deyuan; Sudarshan, T. S.

    2014-10-01

    Shark skin has attracted worldwide attention because of its superior drag reduction, antifouling performance induced from its unique surface morphology. Although the vivid shark skin has been fabricated by a bio-replicated micro-imprinting approach in previous studies and superior drag reduction effect has been validated in water tunnel, continuous large-area fabrication is still an obstacle to wide apply. In this paper, one novel bio-replication coating technology is proposed for large-area transfer of shark skin based on rapid UV curable paint. Apart from design of coating system, bio-replication accuracy of surface morphology was validated about 97% by comparison between shark skin template and coating surface morphology. Finally, the drag reduction and anti-fouling function of coating surface were tested in water tunnel and open algae pond respectively. Drag reduction rate of coating surface was validated about 12% higher and anti-fouling was proved to about hundred times ameliorate, all of which are more excellent than simple 2D riblet surface.

  6. CORRECTIVE ACTION DECISION DOCUMENT FOR THE AREA 3 LANDFILL COMPLEX, TONOPAH TEST RANGE, CAU 424, REVISION 0, MARCH 1998

    Energy Technology Data Exchange (ETDEWEB)

    DOE/NV

    1998-03-03

    This Corrective Action Decision Document (CADD) has been prepared for the Area 3 Landfill Complex (Corrective Action Unit [CAU] 424) in accordance with the Federal Facility Agreement and Consent Order (FFACO) of 1996. Corrective Action Unit 424 is located at the Tonopah Test Range (TTR) and is comprised of the following Corrective Action Sites (CASs), each an individual landfill located around and within the perimeter of the Area 3 Compound (DOE/NV, 1996a): (1) Landfill A3-1 is CAS No. 03-08-001-A301. (2) Landfill A3-2 is CAS No. 03-08-002-A302. (3) Landfill A3-3 is CAS No. 03-08-002-A303. (4) Landfill A3-4 is CAS No. 03-08-002-A304. (5) Landfill A3-5 is CAS No. 03-08-002-A305. (6) Landfill A3-6 is CAS No. 03-08-002-A306. (7) Landfill A3-7 is CAS No. 03-08-002-A307. (8) Landfill A3-8 is CAS No. 03-08-002-A308. The purpose of this CADD is to identify and provide a rationale for the selection of a recommended corrective action alternative for each CAS. The scope of this CADD consists of the following: (1) Develop corrective action objectives. (2) Identify corrective action alternative screening criteria. (3) Develop corrective action alternatives. (4) Perform detailed and comparative evaluations of the corrective action alternatives in relation to the corrective action objectives and screening criteria. (6) Recommend and justify a preferred corrective action alternative for each CAS. In June and July 1997, a corrective action investigation was performed as set forth in the Corrective Action Investigation Plan (CAIP) for CAU No. 424: Area 3 Landfill Complex, Tonopah Test Range, Nevada (DOE/NV, 1997). Details can be found in Appendix A of this document. The results indicated four groupings of site characteristics as shown in Table ES-1. Based on the potential exposure pathways, the following corrective action objectives have been identified for CAU No. 424: (1) Prevent or mitigate human exposure to subsurface soils containing waste. (2) Remediate the site per

  7. Stakeholder collaboration in a prospective World Heritage Area: The case of Kokoda and the Owen Stanley Ranges

    Directory of Open Access Journals (Sweden)

    Amy Louise Bott

    2011-05-01

    Full Text Available The process of listing a World Heritage Area (WHAc in developing countries is often much more complex than in the West. Often all stakeholders are not taken into consideration and there is a lack of understanding of the concept of World Heritage and what it entails. This is particularly true for stakeholders who live in or adjacent to the proposed WHA, such as local communities. This paper presents a case study of Kokoda and the Owen Stanley Ranges, currently a tentative World Heritage site, to show the complexities in stakeholder collaboration and attribution in the process of World Heritage designation. Six key stakeholders were identified in the study. Upon examination of four attributes of stakeholders: power; legitimacy; urgency; and proximity, it was found that all stakeholders in this case study have a high legitimacy in the listing process however only the local community holds high levels of power, urgency and proximity. Additionally it was found that several stakeholders, like the private sector, have too many weak relationships with other stakeholders, resulting in a lack of communication. These findings present the first step in understanding how it might be possible to improve the listing process of World Heritage Sites in developing countries through effective stakeholder collaboration.

  8. Marine organic geochemistry in industrially affected coastal areas in Greece: Hydrocarbons in surface sediments

    Science.gov (United States)

    Hatzianestis, Ioannis

    2015-04-01

    Hydrocarbons are abundant components of the organic material in coastal zones. Their sources are mainly anthropogenic, but several natural ones have also been recognized. Among hydrocarbons, the polycyclic aromatic ones (PAHs) have received special attention since they considered as hazardous environmental chemicals and are included in priority pollutant lists. The purpose of this study was to investigate the distribution, sources and transport pathways of hydrocarbons in marine areas in Greece directly influenced from the operation of major industrial units in the coastal zone by using a molecular marker approach, characteristic compositional patterns and related indices and also to evaluate their potential toxicity. Thirty two surface sediment samples were collected from three marine areas: a) Antikyra bay in Korinthiakos gulf, affected from the operation of an alumina and production plant b) Larymna bay in Noth Evoikos, affected from the operation of a nickel production plant and c) Aliveri bay in South Evoikos Gulf, affected from a cement production plant. In all the studied areas aquaculture and fishing activities have been also developed in the coastal zone. High aliphatic hydrocarbon (AHC) concentrations (~500 μg/g), indicating significant petroleum related inputs, were measured only in Antikyra bay. In all the other samples, AHC values were below 100 μg/g. N-alkanes were the most prominent resolved components (R) with an elevated odd to even carbon number preference, revealing the high importance of terrestrial inputs in the study areas. The unresolved complex mixture (UCM) was the major component of the aliphatic fraction (UCM/R > 4), indicating a chronic oil pollution. A series of hopanes were also identified, with patterns characteristic of oil-derived hydrocarbons, further confirming the presence of pollutant inputs from fossil fuel products. Extremely high PAH concentrations (> 100,000 ng/g) were found in the close vicinity of the alumina production

  9. Improvement of Surface Temperature Prediction Using SVR with MOGREPS Data for Short and Medium range over South Korea

    Science.gov (United States)

    Lim, S. J.; Choi, R. K.; Ahn, K. D.; Ha, J. C.; Cho, C. H.

    2014-12-01

    As the Korea Meteorology Administration (KMA) has operated Met Office Global and Regional Ensemble Prediction System (MOGREPS) with introduction of Unified Model (UM), many attempts have been made to improve predictability in temperature forecast in last years. In this study, post-processing method of MOGREPS for surface temperature prediction is developed with machine learning over 52 locations in South Korea. Past 60-day lag time was used as a training phase of Support Vector Regression (SVR) method for surface temperature forecast model. The selected inputs for SVR are followings: date and surface temperatures from Numerical Weather prediction (NWP), such as GDAPS, individual 24 ensemble members, mean and median of ensemble members for every 3hours for 12 days.To verify the reliability of SVR-based ensemble prediction (SVR-EP), 93 days are used (from March 1 to May 31, 2014). The result yielded improvement of SVR-EP by RMSE value of 16 % throughout entire prediction period against conventional ensemble prediction (EP). In particular, short range predictability of SVR-EP resulted in 18.7% better RMSE for 1~3 day forecast. The mean temperature bias between SVR-EP and EP at all test locations showed around 0.36°C and 1.36°C, respectively. SVR-EP is currently extending for more vigorous sensitivity test, such as increasing training phase and optimizing machine learning model.

  10. Burning velocity and flame surface area in high Karlovitz number flames

    Science.gov (United States)

    Lapointe, Simon; Cheng, Lionel; Blanquart, Guillaume

    2017-11-01

    Accurate knowledge of the burning velocity of turbulent flames is of importance for many combustion devices. For low Karlovitz number flames, Damkohler proposed that the ratio of turbulent to laminar flame speed is proportional to the ratio of turbulent to laminar flame surface area. In recent DNS studies, it has been observed that Damkolher's scaling for low Karlovitz number flames still holds for high Karlovitz number flames. However, recent experimental studies have reported notable differences between global burning velocities and flame surface area measurements. In this work, the numerical and experimental results are further analyzed to explain the apparent contradiction. Emphasis is placed on identifying and quantifying potential experimental limitations at high Karlovitz numbers. More specifically, experimental flame surface measurements typically use binarized PLIF images. These images are two-dimensional and their resolution is limited by that of the PLIF system. The implications of using a two-dimensional iso-contour and the effects of the image resolution are assessed through post-processing of DNS datasets. Furthermore, the effects of integral length scale, Karlovitz number, and differential diffusion on the flame surface area are considered separately.

  11. Area Estimation of Deep-Sea Surfaces from Oblique Still Images.

    Directory of Open Access Journals (Sweden)

    Frederico Carvalho Dias

    Full Text Available Estimating the area of seabed surfaces from pictures or videos is an important problem in seafloor surveys. This task is complex to achieve with moving platforms such as submersibles, towed or remotely operated vehicles (ROV, where the recording camera is typically not static and provides an oblique view of the seafloor. A new method for obtaining seabed surface area estimates is presented here, using the classical set up of two laser devices fixed to the ROV frame projecting two parallel lines over the seabed. By combining lengths measured directly from the image containing the laser lines, the area of seabed surfaces is estimated, as well as the camera's distance to the seabed, pan and tilt angles. The only parameters required are the distance between the parallel laser lines and the camera's horizontal and vertical angles of view. The method was validated with a controlled in situ experiment using a deep-sea ROV, yielding an area estimate error of 1.5%. Further applications and generalizations of the method are discussed, with emphasis on deep-sea applications.

  12. Nanotechnological Advances in Catalytic Thin Films for Green Large-Area Surfaces

    Directory of Open Access Journals (Sweden)

    Suzan Biran Ay

    2015-01-01

    Full Text Available Large-area catalytic thin films offer great potential for green technology applications in order to save energy, combat pollution, and reduce global warming. These films, either embedded with nanoparticles, shaped with nanostructuring techniques, hybridized with other systems, or functionalized with bionanotechnological methods, can include many different surface properties including photocatalytic, antifouling, abrasion resistant and mechanically resistive, self-cleaning, antibacterial, hydrophobic, and oleophobic features. Thus, surface functionalization with such advanced structuring methods is of significance to increase the performance and wide usage of large-area thin film coatings specifically for environmental remediation. In this review, we focus on methods to increase the efficiency of catalytic reactions in thin film and hence improve the performance in relevant applications while eliminating high cost with the purpose of widespread usage. However, we also include the most recent hybrid architectures, which have potential to make a transformational change in surface applications as soon as high quality and large area production techniques are available. Hence, we present and discuss research studies regarding both organic and inorganic methods that are used to structure thin films that have potential for large-area and eco-friendly coatings.

  13. Developing a Novel Hydrogen Sponge with Ideal Binding Energy and High Surface Area for Practical Hydrogen Storage

    Energy Technology Data Exchange (ETDEWEB)

    Chung, T. C. Mike

    2018-04-19

    This Phase I (5 quarters) research project was to examine the validity of a new class of boron-containing polymer (B-polymer) frameworks, serving as the adsorbents for the practical onboard H2 storage applications. Three B-polymer frameworks were synthesized and investigated, which include B-poly(butyenylstyrene) (B-PBS) framework (A), B-poly(phenyldiacetyene) (B-PPDA) framework (B), and B-poly(phenyltriacetylene) (B-PPTA) framework (C). They are 2-D polymer structures with the repeating cyclic units that spontaneously form open morphology and the B-doped (p-type) π-electrons delocalized surfaces. The ideal B-polymer framework shall exhibit open micropores (pore size in the range of 1-1.5nm) with high surface area (>3000 m2/g), and the B-dopants in the conjugated framework shall provide high surface energy for interacting with H2 molecules (an ideal H2 binding energy in the range of 15-25 kJ/mol). The pore size distribution and H2 binding energy were investigated at both Penn State and NREL laboratories. So far, the experimental results show the successful synthesis of B-polymer frameworks with the relatively well-defined planar (2-D) structures. The intrinsically formed porous morphology exhibits a broad pore size distribution (in the range of 0.5-10 nm) with specific surface area (~1000 m2/g). The miss-alignment between 2-D layers may block some micropore channels and limit gas diffusion throughout the entire matrix. In addition, the 2-D planar conjugated structure may also allow free π-electrons delocalization throughout the framework, which significantly reduces the acidity of B-moieties (electron-deficiency).The resulting 2-D B-polymer frameworks only exhibit a small increase of H2 binding energy in the range of 8-9 KJ/mole (quite constant over the whole sorption range).

  14. The reliability of three psoriasis assessment tools: Psoriasis area and severity index, body surface area and physician global assessment.

    Science.gov (United States)

    Bożek, Agnieszka; Reich, Adam

    2017-08-01

    A wide variety of psoriasis assessment tools have been proposed to evaluate the severity of psoriasis in clinical trials and daily practice. The most frequently used clinical instrument is the psoriasis area and severity index (PASI); however, none of the currently published severity scores used for psoriasis meets all the validation criteria required for an ideal score. The aim of this study was to compare and assess the reliability of 3 commonly used assessment instruments for psoriasis severity: the psoriasis area and severity index (PASI), body surface area (BSA) and physician global assessment (PGA). On the scoring day, 10 trained dermatologists evaluated 9 adult patients with plaque-type psoriasis using the PASI, BSA and PGA. All the subjects were assessed twice by each physician. Correlations between the assessments were analyzed using the Pearson correlation coefficient. Intra-class correlation coefficient (ICC) was calculated to analyze intra-rater reliability, and the coefficient of variation (CV) was used to assess inter-rater variability. Significant correlations were observed among the 3 scales in both assessments. In all 3 scales the ICCs were > 0.75, indicating high intra-rater reliability. The highest ICC was for the BSA (0.96) and the lowest one for the PGA (0.87). The CV for the PGA and PASI were 29.3 and 36.9, respectively, indicating moderate inter-rater variability. The CV for the BSA was 57.1, indicating high inter-rater variability. Comparing the PASI, PGA and BSA, it was shown that the PGA had the highest inter-rater reliability, whereas the BSA had the highest intra-rater reliability. The PASI showed intermediate values in terms of interand intra-rater reliability. None of the 3 assessment instruments showed a significant advantage over the other. A reliable assessment of psoriasis severity requires the use of several independent evaluations simultaneously.

  15. A Study of Impermeable Surfaces in the Greater Washington, D.C. Area

    OpenAIRE

    O'Connor, Mary; Chase-Walsh, Sarah; Cerquiera, Stephen

    2014-01-01

    The Washington D.C. area, like many cities, is covered with impermeable surfaces. With millions of cars on the roads every year, runoff is a major problem for the Potomac and the Anacostia rivers, which both empty into the Chesapeake Bay. Large buildings, constant construction, and an extensive highway system contribute to and expedite runoff. We will examine the amount of change in impermeable surfaces throughout the years and the effect runoff has on these two rivers. We also want to look a...

  16. The triazine-based porous organic polymer: Novel synthetic strategy for high specific surface area

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jin Kuen [Dept. of Chemistry, Hankuk University of Foreign Studies, Yongin (Korea, Republic of)

    2017-02-15

    A new type of microporous polymer has been successively synthesized via a simple polycondensation reaction with the 2,4-diaminotriazine moiety and dianhydride monomer. Diaminotriazine moieties in M1 especially can provide effective branching sites, resulting in high surface areas up to 1150 m{sup 2} /g. In addition, the specific pore structure of the polyimide POP in its solid state can be modified by the surface activation method. Therefore, it can be expected that the resulting material will be a promising candidate for gas storage, and with this synthetic strategy, various type of derivatives will also be optimized.

  17. Morphostructural characterization of the Charco basin and its surrounding areas in the Chihuahua segment of north Mexican Basin and Range Province

    Science.gov (United States)

    Troiani, Francesco; Menichetti, Marco

    2014-05-01

    The Chihuahua Basin and Range (CBR) is the eastern branch of the northern Mexican Basin and Range Province that, from a morphostructural point of view, presently is one amongst the lesser-known zones of the southern portion of the North America Basin and Range Province. The study area covers an approximately 800 km2-wide portion of the CBR and encompasses the fault-bounded Charco basin and its surrounding areas. The bedrock of the area pertains to the large siliceous-igneous province of the Sierra Madre Occidental and consists of volcanoclastic rocks including Oligocene dacite, rhyolite, rhyolitic tuffs, and polimitic conglomerates. The region is characterized by a series of NW-SE oriented valleys delimited by tilted monoclinal blocks bounded by high angle, SW-dipping, normal faults. Abrupt changes in elevation, alternating between narrow faulted mountain chains and flat arid valleys or basins are the main morphological elements of the area. The valleys correspond to structural grabens filled with Plio-Pleistocene continental sediments. These grabens are about 10 km wide, while the extensional fault system extend over a distance of more than 15 km. The mountain ranges are in most cases continuous over distances that range from 10 to 70 km including different branches of the extensional and transfer faults. The morphogenesis is mainly erosive in character: erosional landforms (such as rocky scarps, ridges, strath-terraces, erosional pediment, reverse slopes, landslide scar zones, litho-structural flat surfaces) dominate the landscape. In contrast, Quaternary depositional landforms are mainly concentrated within the flat valleys or basins. The Quaternary deposits consist of wide alluvial fans extending to the foot of the main ridges, fluvial and debris-slope deposits. The morphostructural characterization of the area integrated different methodologies, including: i) geomorphological and structural field analyses; ii) remote sensing and geo-morphometric investigations

  18. The Algorithm Theoretical Basis Document for the Derivation of Range and Range Distributions from Laser Pulse Waveform Analysis for Surface Elevations, Roughness, Slope, and Vegetation Heights

    Science.gov (United States)

    Brenner, Anita C.; Zwally, H. Jay; Bentley, Charles R.; Csatho, Bea M.; Harding, David J.; Hofton, Michelle A.; Minster, Jean-Bernard; Roberts, LeeAnne; Saba, Jack L.; Thomas, Robert H.; hide

    2012-01-01

    The primary purpose of the GLAS instrument is to detect ice elevation changes over time which are used to derive changes in ice volume. Other objectives include measuring sea ice freeboard, ocean and land surface elevation, surface roughness, and canopy heights over land. This Algorithm Theoretical Basis Document (ATBD) describes the theory and implementation behind the algorithms used to produce the level 1B products for waveform parameters and global elevation and the level 2 products that are specific to ice sheet, sea ice, land, and ocean elevations respectively. These output products, are defined in detail along with the associated quality, and the constraints, and assumptions used to derive them.

  19. Impervious Surfaces Alter Soil Bacterial Communities in Urban Areas: A Case Study in Beijing, China.

    Science.gov (United States)

    Hu, Yinhong; Dou, Xiaolin; Li, Juanyong; Li, Feng

    2018-01-01

    The rapid expansion of urbanization has caused land cover change, especially the increasing area of impervious surfaces. Such alterations have significant effects on the soil ecosystem by impeding the exchange of gasses, water, and materials between soil and the atmosphere. It is unclear whether impervious surfaces have any effects on soil bacterial diversity and community composition. In the present study, we conducted an investigation of bacterial communities across five typical land cover types, including impervious surfaces (concrete), permeable pavement (bricks with round holes), shrub coverage ( Buxus megistophylla Levl. ), lawns ( Festuca elata Keng ex E. Alexeev ), and roadside trees ( Sophora japonica Linn. ) in Beijing, to explore the response of bacteria to impervious surfaces. The soil bacterial communities were addressed by high-throughput sequencing of the bacterial 16S rRNA gene. We found that Proteobacteria , Actinobacteria , Acidobacteria , Bacteroidetes , Chloroflexi , and Firmicutes were the predominant phyla in urban soils. Soil from impervious surfaces presented a lower bacterial diversity, and differed greatly from other types of land cover. Soil bacterial diversity was predominantly affected by Zn, dissolved organic carbon (DOC), and soil moisture content (SMC). The composition of the bacterial community was similar under shrub coverage, roadside trees, and lawns, but different from beneath impervious surfaces and permeable pavement. Variance partitioning analysis showed that edaphic properties contributed to 12% of the bacterial community variation, heavy metal pollution explained 3.6% of the variation, and interaction between the two explained 33% of the variance. Together, our data indicate that impervious surfaces induced changes in bacterial community composition and decrease of bacterial diversity. Interactions between edaphic properties and heavy metals were here found to change the composition of the bacterial community and diversity

  20. Impervious Surfaces Alter Soil Bacterial Communities in Urban Areas: A Case Study in Beijing, China

    Directory of Open Access Journals (Sweden)

    Yinhong Hu

    2018-02-01

    Full Text Available The rapid expansion of urbanization has caused land cover change, especially the increasing area of impervious surfaces. Such alterations have significant effects on the soil ecosystem by impeding the exchange of gasses, water, and materials between soil and the atmosphere. It is unclear whether impervious surfaces have any effects on soil bacterial diversity and community composition. In the present study, we conducted an investigation of bacterial communities across five typical land cover types, including impervious surfaces (concrete, permeable pavement (bricks with round holes, shrub coverage (Buxus megistophylla Levl., lawns (Festuca elata Keng ex E. Alexeev, and roadside trees (Sophora japonica Linn. in Beijing, to explore the response of bacteria to impervious surfaces. The soil bacterial communities were addressed by high-throughput sequencing of the bacterial 16S rRNA gene. We found that Proteobacteria, Actinobacteria, Acidobacteria, Bacteroidetes, Chloroflexi, and Firmicutes were the predominant phyla in urban soils. Soil from impervious surfaces presented a lower bacterial diversity, and differed greatly from other types of land cover. Soil bacterial diversity was predominantly affected by Zn, dissolved organic carbon (DOC, and soil moisture content (SMC. The composition of the bacterial community was similar under shrub coverage, roadside trees, and lawns, but different from beneath impervious surfaces and permeable pavement. Variance partitioning analysis showed that edaphic properties contributed to 12% of the bacterial community variation, heavy metal pollution explained 3.6% of the variation, and interaction between the two explained 33% of the variance. Together, our data indicate that impervious surfaces induced changes in bacterial community composition and decrease of bacterial diversity. Interactions between edaphic properties and heavy metals were here found to change the composition of the bacterial community and

  1. Investigating the influence of long-range transport on surface O3 in Nevada, USA, using observations from multiple measurement platforms

    International Nuclear Information System (INIS)

    Fine, Rebekka; Miller, Matthieu B.; Yates, Emma L.; Iraci, Laura T.; Gustin, Mae Sexauer

    2015-01-01

    The current United States (US) National Ambient Air Quality Standard (NAAQS) for O 3 (75 ppb) is expected to be revised to between 60 and 70 ppb. As the NAAQS becomes more stringent, characterizing the extent of O 3 and precursors transported into the US is increasingly important. Given the high elevation, complex terrain, and location in the Intermountain West, the State of Nevada is ideally situated to intercept air transported into the US. Until recently, measurements of O 3 and associated pollutants were limited to areas in and around the cities of Las Vegas and Reno. In 2011, the Nevada Rural Ozone Initiative began and through this project 13 surface monitoring sites were established. Also in 2011, the NASA Ames Alpha Jet Atmospheric eXperiment (AJAX) began making routine aircraft measurements of O 3 and other greenhouse gases in Nevada. The availability of aircraft and surface measurements in a relatively rural, remote setting in the Intermountain West presented a unique opportunity to investigate sources contributing to the O 3 observed in Nevada. Our analyses indicate that stratosphere to troposphere transport, long-range transport of Asian pollution, and regional emissions from urban areas and wildfires influence surface observations. The complexity of sources identified here along with the fact that O 3 frequently approaches the threshold being considered for a revised NAAQS indicate that interstate and international cooperation will be necessary to achieve compliance with a more stringent regulatory standard. Further, on a seasonal basis we found no significant difference between daily 1-h maximum O 3 at surface sites, which ranged in elevation from 888 to 2307 m, and aircraft measurements of O 3 < 2500 m which suggests that similar processes influence daytime O 3 across rural Nevada and indicates that column measurements from Railroad Valley, NV are useful in understanding these processes. - Highlights: • Measurements indicate Asian LRT, STT, and

  2. Investigating the influence of long-range transport on surface O{sub 3} in Nevada, USA, using observations from multiple measurement platforms

    Energy Technology Data Exchange (ETDEWEB)

    Fine, Rebekka, E-mail: rebekkafine@gmail.com [Department of Natural Resources and Environmental Science, University of Nevada-Reno, Reno, NV (United States); Miller, Matthieu B. [Department of Natural Resources and Environmental Science, University of Nevada-Reno, Reno, NV (United States); Yates, Emma L.; Iraci, Laura T. [Atmospheric Science Branch, NASA Ames Research Center, Moffett Field, CA 94035 (United States); Gustin, Mae Sexauer, E-mail: mgustin@cabnr.unr.edu [Department of Natural Resources and Environmental Science, University of Nevada-Reno, Reno, NV (United States)

    2015-10-15

    The current United States (US) National Ambient Air Quality Standard (NAAQS) for O{sub 3} (75 ppb) is expected to be revised to between 60 and 70 ppb. As the NAAQS becomes more stringent, characterizing the extent of O{sub 3} and precursors transported into the US is increasingly important. Given the high elevation, complex terrain, and location in the Intermountain West, the State of Nevada is ideally situated to intercept air transported into the US. Until recently, measurements of O{sub 3} and associated pollutants were limited to areas in and around the cities of Las Vegas and Reno. In 2011, the Nevada Rural Ozone Initiative began and through this project 13 surface monitoring sites were established. Also in 2011, the NASA Ames Alpha Jet Atmospheric eXperiment (AJAX) began making routine aircraft measurements of O{sub 3} and other greenhouse gases in Nevada. The availability of aircraft and surface measurements in a relatively rural, remote setting in the Intermountain West presented a unique opportunity to investigate sources contributing to the O{sub 3} observed in Nevada. Our analyses indicate that stratosphere to troposphere transport, long-range transport of Asian pollution, and regional emissions from urban areas and wildfires influence surface observations. The complexity of sources identified here along with the fact that O{sub 3} frequently approaches the threshold being considered for a revised NAAQS indicate that interstate and international cooperation will be necessary to achieve compliance with a more stringent regulatory standard. Further, on a seasonal basis we found no significant difference between daily 1-h maximum O{sub 3} at surface sites, which ranged in elevation from 888 to 2307 m, and aircraft measurements of O{sub 3} < 2500 m which suggests that similar processes influence daytime O{sub 3} across rural Nevada and indicates that column measurements from Railroad Valley, NV are useful in understanding these processes. - Highlights:

  3. Use of surface area computations to describe atom-atom interactions.

    Science.gov (United States)

    de La Cruz, X; Calvo, M

    2001-06-01

    Accessible surface (ASA) and atomic contact (ACA) areas are powerful tools for protein structure analysis. However, their use for analysis purposes could be extended if a relationship between them and protein stability could be found. At present, this is the case only for ASAs, which have been used to assess the contribution of the hydrophobic effect to protein stability. In the present work we study whether there is a relationship between atomic contact areas and the free energy associated to atom-atom interactions. We utilise a model in which the contribution of atomic interactions to protein stability is expressed as a linear function of the accessible surface area buried between atom pairs. We assess the validity of this hypothesis, using a set of 124 lysozyme mutants (Matthews, 1995, Adv Protein Chem, 249-278) for which both the X-ray structure and the experimental stability are known. We tested this assumption for residue representations with increasing numbers of atom types. Our results indicate that for simple residue representations, with only 4 to 5 atom types, there is not a clear linear relationship between stability and buried accessible area. However, this relationship is observed for representations with 6 to 9 atom types, where gross heterogeneities in the atom type definition are eliminated. Finally, we also study a version of the linear model in which the atom- atom interactions are represented utilising a simple function for the buried accessible area, which may be useful for protein structure prediction studies.

  4. Prevalence and spectrum of helminths in free-ranging African buffaloes (Syncerus caffer in wildlife protected areas, Tanzania

    Directory of Open Access Journals (Sweden)

    Emanuel Senyael Swai

    2013-09-01

    Full Text Available Objective: To determine the prevalence and spectrum of helminths in free-ranging African buffaloes in Tanzania by a cross-sectional study. Methods: Faecal samples (n=1 23 from Arusha National Park and Ngorongoro Crater were examined for helminth eggs using sedimentation and floatation techniques during the period of March to June 2012. Results: Coprological examination revealed that 34.1% (n=42 of the buffaloes excreted nematodes and trematodes eggs and protozoan oocyst in their faces. The pattern of infection was either single or mixed. Single (52.4% and concurrent infections with two, three, four and five parasites were recorded in 19.0%, 11.9%, 14.3% and 2.3% respectively of the cases. The nematode eggs encountered were those of Trichostrongylus sp. (20.3%, Oesophagostomum sp. (7.3%, Strongyle sp. (4.1%, Bunostomum sp. (4.1%, Ostertegia sp. (3.3% and Toxocara sp. (2.4%. The trematode eggs encountered were those of Fasciola sp. (9.8%, Paramphistomum sp. (4.9%, Gastrothylax sp. (1.6%, Ornithobilharzia sp. (0.81% and Fischoederius sp (0.81%. The protozoan oocyst recorded was that of Eimeria sp. (8.1%. Geographical location of buffaloes had significant influence on the prevalence of infection with Trichostrongylus (P=0.046 and Fasciola (P=0.001, and the mean prevalances in Arusha National Park are significantly higher than those in Ngorongoro Crater. Age had significant influence on infection with Fasciola (P=0.036, and juvenile recorded higher levels of infection than sub-adults. Health status, body condition score and sex-wise prevalence of helminths were not significant (P>0.05. Conclusions: This study indicates that helminths species are numerous and highly prevalent in the two protected areas and may be one of the contributing factors to lower buffalo productivity.

  5. [Distribution Characteristics of Fluoroquinolones Antibiotics in Surface Water and Groundwater from Typical Areas in A City].

    Science.gov (United States)

    Cui, Ya-feng; He, Jiang-tao; Su, Si-hui; Yang, Lei; Qiao, Xiao-cui

    2015-11-01

    In order to investigate the characteristics of 5 typical kinds of fluoroquinolones (FQs) pollution in waters from a city, surface water and groundwater samples from main drainage rivers and typical areas were collected, respectively. The conventional test and FQs concentrations analysis of the water samples were conducted. The results showed the concentration and composition of FQs in groundwater differed substantially from those in surface water. The average concentration of FQs in surface water was 789.1 ng x L(-1) with the main components of ofloxacin (OFL) and lomefloxacin (LOM). This value was higher than the average concentration of FQs in groundwater: 342.7 ng x L(-1) with the main components of norfloxacin (NOR) and lomefloxacin (LOM). The enrofloxacin (ENR) exhibited relatively lower levels in both surface water and groundwater as compared to others. The highest FQs concentrations in surface water were found in trenches, followed by tributaries and the main stream. For groundwater, FQs concentrations were relatively higher in the sewage riverside. A decreasing trend of FQs concentration was monitored with the increasing distance of sampling points to the drainage rivers and all components mentioned above showed similar changing trends. The results of this study preliminarily indicated that FQs in groundwater along the riverside probably came from the surface water.

  6. Assessment of Radioactive Materials and Heavy Metals in the Surface Soil around the Bayanwula Prospective Uranium Mining Area in China.

    Science.gov (United States)

    Bai, Haribala; Hu, Bitao; Wang, Chengguo; Bao, Shanhu; Sai, Gerilemandahu; Xu, Xiao; Zhang, Shuai; Li, Yuhong

    2017-03-14

    The present work is the first systematic and large scale study on radioactive materials and heavy metals in surface soil around the Bayanwula prospective uranium mining area in China. In this work, both natural and anthropogenic radionuclides and heavy metals in 48 surface soil samples were analyzed using High Purity Germanium (HPGe) γ spectrometry and inductively coupled plasma-mass spectrometry (ICP-MS). The obtained mean activity concentrations of 238 U, 226 Ra, 232 Th, 40 K, and 137 Cs were 25.81 ± 9.58, 24.85 ± 2.77, 29.40 ± 3.14, 923.0 ± 47.2, and 5.64 ± 4.56 Bq/kg, respectively. The estimated average absorbed dose rate and annual effective dose rate were 76.7 ± 3.1 nGy/h and 83.1 ± 3.8 μ Sv, respectively. The radium equivalent activity, external hazard index, and internal hazard index were also calculated, and their mean values were within the acceptable limits. The estimated lifetime cancer risk was 3.2 × 10 -4 /Sv. The heavy metal contents of Cr, Ni, Cu, Zn, As, Cd, and Pb from the surface soil samples were measured and their health risks were then assessed. The concentrations of all heavy metals were much lower than the average backgrounds in China except for lead which was about three times higher than that of China's mean. The non-cancer and cancer risks from the heavy metals were estimated, which are all within the acceptable ranges. In addition, the correlations between the radionuclides and the heavy metals in surface soil samples were determined by the Pearson linear coefficient. Strong positive correlations between radionuclides and the heavy metals at the 0.01 significance level were found. In conclusion, the contents of radionuclides and heavy metals in surface soil around the Bayanwula prospective uranium mining area are at a normal level.

  7. Effect of preparation surface area on the clinical outcome of full veneer crowns in dogs.

    Science.gov (United States)

    Riehl, Jessica; Soukup, Jason W; Collins, Caitlyn; Siverling, Sarah; Ploeg, Heidi-Lynn; Snyder, Christopher J

    2014-01-01

    Crown therapy is commonly used in veterinary medicine to provide support to teeth which have previously fractured, received root canal therapy, have significant wear, or experienced other detrimental removal of tooth substance. As with several aspects of veterinary medicine, many of the recommendations or guidelines for crown therapy originate from human dentistry, which are then transferred to veterinary patients. Due to the significant difference in the anatomy of teeth and function of the oral cavity between humans and dogs, these guidelines need to be studied to determine the appropriateness of their use in veterinary patients. This article evaluates the relationship between surface area of the preparation and clinical outcome of full veneer crown therapy of the canine tooth in dogs. Although there appeared to be a positive relationship between preparations with greater surface area and successful clinical outcome, it was not found to be statistically significant.

  8. Phenomenological study of aerosol dry deposition in urban area: surface properties, turbulence and local meteorology influences

    International Nuclear Information System (INIS)

    Roupsard, P.

    2013-01-01

    Aerosol dry deposition is not much known for urban areas due to the lack of data. Knowledge on this phenomenon is necessary to understand pollutant fluxes in cities and to estimate inhabitant exposition to ionizing radiation of radioactive aerosols. A data providing could enable to enhance dry deposition models for these areas. An original experimental approach is performed to study submicron aerosol dry deposition on urban surfaces. Wind tunnel coupled to in situ experiments give results to study different physical phenomenon governing dry deposition. Dry deposition velocities are measured using aerosol tracers. These data are associated to turbulent and meteorological measured conditions. This database permits to classify the principal physical phenomenon for each experiment type. Finally, different phenomenon must be considered for chronic and acute exposition of urban surfaces to atmospheric particles. (author)

  9. Soil movements and surface erosion rates on rocky slopes in the mountain areas of the karst region of Southwest China

    Science.gov (United States)

    Zhang, X. B.; Bai, X. Y.; Long, Y.

    2012-04-01

    The karst region of Southwest China with an area of 54 × 104 km2 is one of the largest karst areas in the world and experiences subtropical climate. Hill-depressions are common landforms in the mountain areas of this region. Downslope soil movement on the ground by surface water erosion and soil sinking into underground holes by creeping or pipe erosion are mayor types of soil movements on rocky carbonate slopes. The 137Cs technique was used to date the sediment deposits in six karst depressions, to estimate average surface erosion rates on slopes from their catchments. The estimates of soil loss rates obtained from this study evidenced considerable variability. A value of 1.0 t km-2 year-1 was obtained for a catchment under original dense karst forest, but the erosion rates ranged between 19.3 t km-2 year-1 and 48.7 t km-2 year-1 in four catchments under secondary forest or grasses, where the original forest cover had been removed in the Ming and Qing dynasties, several hundred years ago. The highest rate of 1643 t km-2 year-1 was obtained for a catchment underlain by clayey carbonate rocks, where the soil cover was thicker and more extensive than in the other catchments and extensive land reclamation for cultivation had occurred during the period 1979-1981, immediately after the Cultural Revolution.

  10. The influence of band sum area, domain extent, and range sizes on the latitudinal mid-domain effect

    DEFF Research Database (Denmark)

    Romdal, Tom Skovlund; Colwell, Robert K.; Rahbek, Carsten

    2005-01-01

    of latitudinal distributions of New World birds (3706 species) on a 1° scale. Two previously published data sets for other taxa are also considered. We adjusted band sums (number of species per latitudinal band) for longitudinal area by constructing species-area curves for each band. Area-corrected richness...... patterns differed substantially from raw band sums, although both confirmed a strong, mid-tropical peak in richness. An MDE model accounted for 47% of the adjusted pattern, whereas area alone explained 13% of variation. Area-adjusted band sum data proved preferable to coastal transect data from the same...

  11. Surface area of lactose and lactose granulates on consolidation and compaction

    OpenAIRE

    Riepma, Klaas Alouis

    1993-01-01

    This dissertation discusses the effect of short time storage at different conditions on the strength and the specific BET surface area of lactose tablets. In addition, some aspects are studied of the consolidation and compaction properties of crystalline lactose fractions in heterogeneous systems. The crystalline lactose types used are: a-lactose monohydrate, anhydrous a-lactose, crystalline B-lactose and roller dried B-lactose. ... Zie: Summary

  12. Synthesis of high-surface-area spinel-type MgAl2O4 nanoparticles ...

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 40; Issue 1. Synthesis of high-surface-area spinel-type MgAl 2 O 4 nanoparticles by [Al(sal) 2 (H 2 O) 2 ] 2 [Mg(dipic) 2 ] and [Mg(H 2 O) 6 ][Al(ox) 2 (H 2 O) 2 ] 2 ·5H 2 O: influence of inorganic precursor type. Volume 40 Issue 1 February 2017 pp 45-53 ...

  13. Sensitivity analysis of the surface water- groundwater interaction for the sandy area of the Netherlands

    OpenAIRE

    Gomez del Campo, E.; Jousma, G.; Massop, H.T.L.

    1993-01-01

    The "Sensitivity Analysis of the Surface Water- Groundwater Interaction for the Sandy Area of the Netherlands" was carried out in the framework of a bilateral research project in support of the implementation of a nationwide geohydrological information system (REGIS) in the Netherlands. This project, conducted in cooperation between the TNO Institute for Applied Scientific Research (IGG-TNO) and !he Winand Staring Centre for Integrated Land, Soil and Water Research (SC-DLO), is aimed at defin...

  14. Formula and Scale for Body Surface Area Estimation in High-Risk Infants

    OpenAIRE

    Ahn, Youngmee

    2010-01-01

    Advances in medical technology and the health sciences have lead to a rapid increase in the prevalence and morbidity of high-risk infants with chronic or permanent sequels such as the birth of early preterm infants. A suitable formula is therefore needed for body surface area (BSA) estimation for high-risk infants to more accurately devise therapeutic regimes in clinical practice. A cohort study involving 5014 high-risk infants was conducted to develop a suitable formula for estimating BSA us...

  15. n-Alkylamine-assisted preparation of a high surface area vanadyl phosphate/tetraethylorthosilicate nanocomposite

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, João Paulo L., E-mail: billbrujah@yahoo.com.br [Departamento de Química, Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, Universidade de São Paulo, Av. Bandeirantes 3900, Ribeirão Preto, SP 14040-901 (Brazil); Zampronio, Elaine C.; Oliveira, Herenilton P. [Departamento de Química, Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, Universidade de São Paulo, Av. Bandeirantes 3900, Ribeirão Preto, SP 14040-901 (Brazil)

    2013-02-15

    Graphical abstract: CuK{sub α} X-ray diffraction patterns of the VP, VPOc, VPOcT, VPOcT200 and VPOcT500. Highlights: ► TEOS and octylamine incorporation into the VP was achieved by expanding the lamellar. ► The specific surface area increased from 15 m{sup 2} g{sup −1} in VP to 237 m{sup 2} g{sup −1} in VPOcT. ► The VPOcT exhibited thermal resistance up to 200 °C in air. ► Upon thermal treatment up to 500 °C, the surface area increased to 838 m{sup 2} g{sup −1}. -- Abstract: We have developed a vanadyl phosphate/tetraethylorthosilicate (VPO/TEOS) nanocomposite comprised of silicate chains interleaved with VPO layers, prepared by using an n-alkylamines such as octylamine as the structure directing agent. The nanocomposites were synthesized by reacting amine-intercalated vanadyl phosphate with tetraethylorthosilicate via the soft chemistry approach. The synthetic procedure encompassed the exfoliation of the layered vanadyl phosphate as well as the reorganization of this exfoliated solid into a mesostructured lamellar phase with the same V–P–O connectivity as in the original matrix. TEOS incorporation into the vanadyl phosphate was achieved by expanding the lamellar structure with n-alkylamine (Δd = 13 Å with n-octylamine). The specific surface area increased from 15 m{sup 2} g{sup −1} in the vanadyl phosphate matrix to 237 m{sup 2} g{sup −1} in VPOcT, and the isotherm curves revealed the characteristic hysteresis of mesoporous materials. Upon thermal treatment up to 500 °C, the surface area increased to 837 m{sup 2} g{sup −1}, which is suitable for catalytic purposes.

  16. Growth of Hierarchically Structured High-Surface Area Alumina on FeCrAl Alloy Wires

    Directory of Open Access Journals (Sweden)

    Chandni Rallan

    2013-01-01

    Full Text Available The formation of metastable alumina phases due to the oxidation of commercial FeCrAl alloy wires (0.5 mm thickness at various temperatures and time periods has been examined. Samples were isothermally oxidised in air using a thermogravimetric analyzer (TGA. The morphology of the oxidised samples was analyzed using an Electronic Scanning Electron Microscope (ESEM and X-ray on the surface analysis was done using an Energy Dispersive X-Ray (EDX analyzer. The technique of X-Ray Diffraction (XRD was used to characterize the phase of the oxide growth. The entire study showed that it was possible to grow high-surface area gamma alumina on the FeCrAl alloy wire surfaces when isothermally oxidised above 800°C over several hours.

  17. Surface impedance of BaFe2-xNixAs2 in the radio frequency range

    Directory of Open Access Journals (Sweden)

    A. Abbassi

    2012-08-01

    Full Text Available We report measurements of the temperature dependence of the surface impedance in superconducting BaFe1.93Ni0.07As2 crystals using the radiofrequency reflection technique in the 5range. An LC resonant circuit with a phase sensitive detection was used at 92MHz. A measurement assembly with point contacts was used at 30MHz. The recent discovery of iron based arsenide superconductors BaFe2-xNixAs2 has attracted much interest. For a Ni doping level of 7% the superconducting phase transition is found around 20K. The temperature dependence of the superconducting penetration depth was determined.

  18. Description of climate, surface hydrology, and near-surface hydrogeology. Preliminary site description. Forsmark area - version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Johansson, Per-Olof [Artesia Grundvattenkonsult AB, Stockholm (Sweden); Werner, Kent [SWECO VIAK AB/Golder Associates AB, Stockholm (Sweden); Bosson, Emma; Berglund, Sten [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Juston, John [DBE Sweden, Uppsala (Sweden)

    2005-06-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) is conducting site investigations at two different locations, the Forsmark and Simpevarp areas, with the objective of siting a geological repository for spent nuclear fuel. The results from the investigations at the sites are used as a basic input to the development of Site Descriptive Models (SDM). The SDM shall summarise the current state of knowledge of the site, and provide parameters and models to be used in further analyses within Safety Assessment, Repository Design and Environmental Impact Assessment. The present report is a background report describing the meteorological conditions and the modelling of surface hydrology and near-surface hydrogeology in support of the Forsmark version 1.2 SDM based on the data available in the Forsmark 1.2 'data freeze' (July 31, 2004). The groundwater is very shallow, with groundwater levels within one meter below ground as an annual mean for almost all groundwater monitoring wells. Also, the annual groundwater level amplitude is less than 1.5 m for most wells. The shallow groundwater levels mean that there is a strong interaction between evapotranspiration, soil moisture and groundwater. In the modelling, surface water and near-surface groundwater divides are assumed to coincide. The small-scale topography implies that many local, shallow groundwater flow systems are formed in the Quaternary deposits, overlaying more large-scale flow systems associated with groundwater flows at greater depths. Groundwater level time series from wells in till and bedrock within the same areas show a considerably higher groundwater level in the till than in the bedrock. The observed differences in levels are not fully consistent with the good hydraulic contact between overburden and bedrock indicated by the hydraulic tests in the Quaternary deposits. However, the relatively lower groundwater levels in the bedrock may be caused by the horizontal to sub-horizontal highly

  19. How Much Global Burned Area Can Be Forecast on Seasonal Time Scales Using Sea Surface Temperatures?

    Science.gov (United States)

    Chen, Yang; Morton, Douglas C.; Andela, Niels; Giglio, Louis; Randerson, James T.

    2016-01-01

    Large-scale sea surface temperature (SST) patterns influence the interannual variability of burned area in many regions by means of climate controls on fuel continuity, amount, and moisture content. Some of the variability in burned area is predictable on seasonal timescales because fuel characteristics respond to the cumulative effects of climate prior to the onset of the fire season. Here we systematically evaluated the degree to which annual burned area from the Global Fire Emissions Database version 4 with small fires (GFED4s) can be predicted using SSTs from 14 different ocean regions. We found that about 48 of global burned area can be forecast with a correlation coefficient that is significant at a p burning. Continental regions where burned area had a higher degree of predictability included equatorial Asia, where 92% of the burned area exceeded the correlation threshold, and Central America, where 86% of the burned area exceeded this threshold. Pacific Ocean indices describing the El Nino-Southern Oscillation were more important than indices from other ocean basins, accounting for about 1/3 of the total predictable global burned area. A model that combined two indices from different oceans considerably improved model performance, suggesting that fires in many regions respond to forcing from more than one ocean basin. Using OCI-burned area relationships and a clustering algorithm, we identified 12 hotspot regions in which fires had a consistent response to SST patterns. Annual burned area in these regions can be predicted with moderate confidence levels, suggesting operational forecasts may be possible with the aim of improving ecosystem management.

  20. [Distribution, surface and protected area of palm-swamps in Costa Rica and Nicaragua].

    Science.gov (United States)

    Serrano-Sandí, Juan; Bonilla-Murillo, Fabian; Sasa, Mahmood

    2013-09-01

    In Central America, palm swamps are known collectively as yolillales. These wetlands are usually dominated by the raffia palm Raphia taedigera, but also by the royal palm Manicaria saccifera and -in lower extensions- by the American oil palm Elaeis oleifera. The yolillales tend to be poor in woody species and are characteristic of regions with high rainfall and extensive hydroperiods, so they remain flooded most of the year. The dominance of large raffia palm leaves in the canopy, allow these environments to be distinguishable in aerial photographs, which consequently has helped to map them along most of their distribution. However, while maps depicting yolillales are available, the extent of their surface area, perimeter and connectivity remains poorly understood. This is particularly true for yolillales in Costa Rica and Nicaragua, countries that share a good proportion of palm dominated swaps in the Rio San Juan Basin. In addition, it is not known the actual area of these environments that is under any category of protection according to the conservation systems of both countries. As a first step to catalog yolillal wetlands in Costa Rica and Nicaragua, this paper evaluates cartographic maps to delineate yolillales in the region. A subsample of yolillales mapped in this study were visited and we geo-referenced them and evaluate the extent and condition of the swamp. A total of 110 883.2ha are classified as yolillales in Nicaragua, equivalent to 22% of wetland surface area recorded for that country (excluding the Cocibolca and Xolothn Lakes). In Costa Rica, 53 931.3ha are covered by these palm dominated swamps, which represent 16.24% of the total surface area covered by wetlands. About 47% of the area covered by yolillales in Nicaragua is under some category of protection, the largest extensions protected by Cerro Silva, Laguna Tale Sulumas and Indio Maiz Nature Reserves. In Costa Rica, 55.5% of the area covered by yolillal is located within protected areas

  1. Geographical altitude, size, mass and body surface area in children (1-4 years) in the Province of Jujuy (Argentina).

    Science.gov (United States)

    Román, Estela María; Bejarano, Ignacio Felipe; Alfaro, Emma Laura; Abdo, Guadalupe; Dipierri, José Edgardo

    2015-01-01

    Highland child populations show low growth rates. To evaluate the variation of size, mass and body surface area of Jujenean infants (1-4 years) as a function of geographic altitude. Nutritional status of 8059 healthy infants was determined based on weight and height data; body mass index, ponderal index, body surface area, body surface area/mass and ectomorphy were calculated. Variables were standardized with a provincial mean and WHO references. Data were grouped by age, sex and geographic altitude: Highlands (≥2500 masl) and Lowlands (children differ in size, mass and body surface area based on the geographical altitude and adverse nutritional and socioeconomic factors.

  2. Kilohertz Electrical Stimulation Nerve Conduction Block: Effects of Electrode Surface Area.

    Science.gov (United States)

    Patel, Yogi A; Kim, Brian S; Rountree, William S; Butera, Robert J

    2017-10-01

    Kilohertz electrical stimulation (KES) induces repeatable and reversible conduction block of nerve activity and is a potential therapeutic option for various diseases and disorders resulting from pathological or undesired neurological activity. However, successful translation of KES nerve block to clinical applications is stymied by many unknowns, such as the relevance of the onset response, acceptable levels of waveform contamination, and optimal electrode characteristics. We investigated the role of electrode geometric surface area on the KES nerve block threshold using 20- and 40-kHz current-controlled sinusoidal KES. Electrodes were electrochemically characterized and used to characterize typical KES waveforms and electrode charge characteristics. KES nerve block amplitudes, onset duration, and recovery of normal conduction after delivery of the KES were evaluated along with power requirements for effective KES nerve block. Results from this investigation demonstrate that increasing electrode geometric surface area provides for a more power-efficient KES nerve block. Reductions in block threshold by increased electrode surface area were found to be KES-frequency-dependent, with block thresholds and average power consumption reduced by greater than two times with 20-kHz KES waveforms and greater than three times for 40-kHz KES waveforms.

  3. Detailed effects of particle size and surface area on 222Rn emanation of a phosphate rock.

    Science.gov (United States)

    Haquin, Gustavo; Yungrais, Zohar; Ilzycer, Danielle; Zafrir, Hovav; Weisbrod, Noam

    2017-12-01

    The dependency of radon emanation on soil texture was investigated using the closed chamber method. Ground phosphate rock with a large specific surface area was analyzed, and the presence of inner pores, as well as a high degree of roughness and heterogeneity in the phosphate particles, was found. The average radon emanation of the dry phosphate was 0.145 ± 0.016. The emanation coefficient was highest (0.169 ± 0.019) for the smallest particles (210 μm). The reduction rate followed an inverse power law. As expected, a linear dependence between the emanation coefficient and the specific surface area was found, being lower than predicted for the large specific surface area. This was most likely due to an increase in the embedding effect of radon atoms in adjacent grains separated by micropores. Results indicate that knowledge of grain radium distribution is crucial to making accurate emanation predictions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Preparation of high surface area and high conductivity polyaniline nanoparticles using chemical oxidation polymerization technique

    Science.gov (United States)

    Budi, S.; Yusmaniar; Juliana, A.; Cahyana, U.; Purwanto, A.; Imaduddin, A.; Handoko, E.

    2018-03-01

    In this work, polyaniline nanoparticles were synthesized using a chemical oxidation polymerization technique. The ammonium peroxydisulfate (APS)/aniline ratio, APS dropping time, and polymerization temperature were optimized to increase the surface area and conductivity of the polyaniline.The Fourier-transform infrared (FTIR) spectrum confirmed the formation of emeraldine salt polyaniline. X-ray diffraction (XRD) patterns indicated that amorphous and crystalline phases of the polyaniline were formed with crystallinity less than 40%. Scanning electron microscope (SEM) micrographs showed that the finest nanoparticles with uniform size distribution were obtained at the polymerization temperature of 0°C. A surface area analyzer (SAA) showed that the highest Brunauer-Emmett-Teller surface area (SBET ) of 42.14 m2/gwas obtained from an APS/aniline ratio of 0.75 with a dropping time of 0 s at a polymerization temperature of 0°C. A four-point probe measurement conducted at 75–300K indicated relatively high conductivity of the semiconductor characteristic of the polyaniline.

  5. Effects of acid treatment on the clay palygorskite: XRD, surface area, morphological and chemical composition

    Energy Technology Data Exchange (ETDEWEB)

    Xavier, Katiane Cruz Magalhaes; Santos, Maria do Socorro Ferreira dos; Santos, Maria Rita Morais Chaves; Oliveira, Marilia Evelyn Rodrigues; Osajima, Josy Antevelli; Silva Filho, Edson Cavalcanti da [Universidade Federal do Piaui (UFPI), Teresina, PI (Brazil); Carvalho, Maria Wilma Nunes Cordeiro, E-mail: edsonfilho@ufpi.edu.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

    2014-08-15

    The palygorskite is an aluminum-magnesium silicate that has a fibrous morphology. Their physicochemical characteristics are the result of high surface area, porosity and thermal resistance which make it an attractive adsorbent. Its adsorption capacity can be increased through chemical reactions and/or heat treatments. The objective of this work is to verify the effects of acid activation on the palygorskite, treated with HCl at 90 °C at concentrations of 2, 4 and 6 mol L{sup -1} in 2 and 4 hours, with clay/acid solution ratio 1 g 10 mL{sup -1} and characterized by techniques: XRF, XRD and surface area. A significant increase in specific surface area was observed in the sample treated with HCl at the concentration 6 mol L{sup -1}. The changes were more pronounced at stricter concentrations of acidity, with decreasing intensity of reflection of the clay indicated in the XRD. These changes were confirmed in the XRF with the leaching of some oxides and with increasing concentration of SiO{sub 2}. (author)

  6. Relationship Between the Surface Area to Volume Ratio and Temperature across Geologic Time in Ostracods

    Science.gov (United States)

    Jackson, C.; Zaroff, S.; Heim, N. A.; Payne, J.

    2014-12-01

    In 1877 Joseph Allen proposed that endothermic terrestrial organisms would have lower surface area to volume ratios (SAVR) in colder climates and higher SAVRs in warmer climates. With a smaller surface area compared to volume, organisms can retain more heat in cold climates. We tested to see if this principle applied to ostracods, a type of ectothermic marine invertebrate. We hypothesised that Allen's rule applies to ostracods, as Allen's rule has been demonstrated in frogs (Alho 2011), which are also ectotherms . We used the linear dimensions of the three major carapace axes of ostracod holotypes to estimate the SAVR. We compared ostracod SAVRs with paleotemperatures from Royer et al. (2004). We found that there was a correlation between surface area and temperature; it is a small, but statistically significant correlation (adj. R2=0.0167). This means that as temperature increased, the SAVR also increased. We also found a negative correlation between ostracod SAVR to geologic time(adj. R2=0.0114), which shows us that as time has gone on, ostracod SAVR has decreased. We then plotted the correlation coefficient of SAVR to temperature over geologic time to explore trends in the strength of Allen's rule. For most of time there was no relationship but during the Devonian, Allen's Rule did explain the trend. In short, temperature does explain some of the correlation between the SAVR and temperature, but it is likely there were other environmental factors affecting this relationship.

  7. Mineral paragenesis on Mars: The roles of reactive surface area and diffusion.

    Science.gov (United States)

    Fairén, Alberto G; Gil-Lozano, Carolina; Uceda, Esther R; Losa-Adams, Elisabeth; Davila, Alfonso F; Gago-Duport, Luis

    2017-09-01

    Geochemical models of secondary mineral precipitation on Mars generally assume semiopen systems (open to the atmosphere but closed at the water-sediment interface) and equilibrium conditions. However, in natural multicomponent systems, the reactive surface area of primary minerals controls the dissolution rate and affects the precipitation sequences of secondary phases, and simultaneously, the transport of dissolved species may occur through the atmosphere-water and water-sediment interfaces. Here we present a suite of geochemical models designed to analyze the formation of secondary minerals in basaltic sediments on Mars, evaluating the role of (i) reactive surface areas and (ii) the transport of ions through a basalt sediment column. We consider fully open conditions, both to the atmosphere and to the sediment, and a kinetic approach for mineral dissolution and precipitation. Our models consider a geochemical scenario constituted by a basin (i.e., a shallow lake) where supersaturation is generated by evaporation/cooling and the starting point is a solution in equilibrium with basaltic sediments. Our results show that cation removal by diffusion, along with the input of atmospheric volatiles and the influence of the reactive surface area of primary minerals, plays a central role in the evolution of the secondary mineral sequences formed. We conclude that precipitation of evaporites finds more restrictions in basaltic sediments of small grain size than in basaltic sediments of greater grain size.

  8. Potential effects of groundwater and surface water contamination in an urban area, Qus City, Upper Egypt

    Science.gov (United States)

    Abdalla, Fathy; Khalil, Ramadan

    2018-05-01

    The potential effects of anthropogenic activities, in particular, unsafe sewage disposal practices, on shallow groundwater in an unconfined aquifer and on surface water were evaluated within an urban area by the use of hydrogeological, hydrochemical, and bacteriological analyses. Physicochemical and bacteriological data was obtained from forty-five sampling points based on33 groundwater samples from variable depths and 12 surface water samples. The pollution sources are related to raw sewage and wastewater discharges, agricultural runoff, and wastewater from the nearby Paper Factory. Out of the 33 groundwater samples studied, 17 had significant concentrations of NO3-, Cl- and SO42-, and high bacteria counts. Most of the water samples from the wells contained high Fe, Mn, Pb, Zn, Cd, and Cr. The majority of surface water samples presented high NO3- concentrations and high bacteria counts. A scatter plot of HCO3- versus Ca indicates that 58% of the surface water samples fall within the extreme contamination zone, while the others are within the mixing zone; whereas 94% of groundwater samples showed evidence of mixing between groundwater and wastewater. The bacteriological assessment showed that all measured surface and groundwater samples contained Escherichia coli and total coliform bacteria. A risk map delineated four classes of contamination, namely, those sampling points with high (39.3%), moderate (36.3%), low (13.3%), and very low (11.1%) levels of contamination. Most of the highest pollution points were in the middle part of the urban area, which suffers from unmanaged sewage and industrial effluents. Overall, the results demonstrate that surface and groundwater in Qus City are at high risk of contamination by wastewater since the water table is shallow and there is a lack of a formal sanitation network infrastructure. The product risk map is a useful tool for prioritizing zones that require immediate mitigation and monitoring.

  9. Continued decrease of open surface water body area in Oklahoma during 1984-2015.

    Science.gov (United States)

    Zou, Zhenhua; Dong, Jinwei; Menarguez, Michael A; Xiao, Xiangming; Qin, Yuanwei; Doughty, Russell B; Hooker, Katherine V; David Hambright, K

    2017-10-01

    Oklahoma contains the largest number of manmade lakes and reservoirs in the United States. Despite the importance of these open surface water bodies to public water supply, agriculture, thermoelectric power, tourism and recreation, it is unclear how these water bodies have responded to climate change and anthropogenic water exploitation in past decades. In this study, we used all available Landsat 5 and 7 images (16,000 scenes) from 1984 through 2015 and a water index- and pixel-based approach to analyze the spatial-temporal variability of open surface water bodies and its relationship with climate and water exploitation. Specifically, the areas and numbers of four water body extents (the maximum, year-long, seasonal, and average extents) were analyzed to capture variations in water body area and number. Statistically significant downward trends were found in the maximum, year-long, and annual average water body areas from 1984 through 2015. Furthermore, these decreases were mainly attributed to the continued shrinking of large water bodies (>1km 2 ). There were also significant decreases in maximum and year-long water body numbers, which suggested that some of the water bodies were vanishing year by year. However, remarkable inter-annual variations of water body area and number were also found. Both water body area and number were positively related to precipitation, and negatively related to temperature. Surface water withdrawals mainly influenced the year-long water bodies. The smaller water bodies have a higher risk of drying under a drier climate, which suggests that small water bodies are more vulnerable under climate-warming senarios. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. Definition of intrusion scenarios and example concentration ranges for the disposal of near-surface waste at the Hanford Site

    International Nuclear Information System (INIS)

    Aaberg, R.L.; Kennedy, W.E. Jr.

    1990-10-01

    The US Department of Energy (DOE) is in the process of conducting performance assessments of its radioactive waste sites and disposal systems to ensure that public health and safety are protected, the environment is preserved, and that no remedial actions after disposal are required. Hanford Site low-level waste performance assessments are technical evaluations of waste sites or disposal systems that provide a basis for making decisions using established criteria. The purpose of this document is to provide a family of scenarios to be considered when calculating radionuclide exposure to individuals who may inadvertently intrude into near-surface waste disposal sites. Specific performance assessments will use modifications of the general scenarios described here to include additional site/system details concerning the engineering design, waste form, inventory, and environmental setting. This document also describes and example application of the Hanford-specific scenarios in the development of example concentration ranges for the disposal of near-surface wastes. The overall goal of the example calculations is to illustrate the application of the scenarios in a performance assessment to assure that people in the future cannot receive a dose greater than an established limit. 24 refs., 2 figs., 5 tabs

  11. Decadal changes of surface elevation over permafrost area estimated using reflected GPS signals

    Science.gov (United States)

    Liu, Lin; Larson, Kristine M.

    2018-02-01

    Conventional benchmark-based survey and Global Positioning System (GPS) have been used to measure surface elevation changes over permafrost areas, usually once or a few times a year. Here we use reflected GPS signals to measure temporal changes of ground surface elevation due to dynamics of the active layer and near-surface permafrost. Applying the GPS interferometric reflectometry technique to the multipath signal-to-noise ratio data collected by a continuously operating GPS receiver mounted deep in permafrost in Barrow, Alaska, we can retrieve the vertical distance between the antenna and reflecting surface. Using this unique kind of observables, we obtain daily changes of surface elevation during July and August from 2004 to 2015. Our results show distinct temporal variations at three timescales: regular thaw settlement within each summer, strong interannual variability that is characterized by a sub-decadal subsidence trend followed by a brief uplift trend, and a secular subsidence trend of 0.26 ± 0.02 cm year-1 during 2004 and 2015. This method provides a new way to fully utilize data from continuously operating GPS sites in cold regions for studying dynamics of the frozen ground consistently and sustainably over a long time.

  12. Cryptic oxygen oases: Hypolithic photosynthesis in hydrothermal areas and implications for Archean surface oxidation

    Science.gov (United States)

    Havig, J. R.; Hamilton, T. L.

    2017-12-01

    Mounting geochemical evidence suggests microorganisms capable of oxygenic photosynthesis (e.g., Cyanobacteria) colonized Archean continental surfaces, driving oxidative weathering of detrital pyrites prior to the 2.5 Ga great oxidation event. Modern terrestrial environments dominated by single-celled phototrophs include hydrothermal systems (e.g., Yellowstone National Park) and hypolithic communities found in arid to hyper-arid deserts (e.g., McMurdo Dry Valleys of Antarctica, Atacama Desert of Chile). Recent work indicates terrestrial hydrothermal systems date back at least as far as 3.5 Ga. Here, we explore phototrophic communities in both hypolithic (sub-sinter) and hydrothermal (subaqueous and subaerial) environments in Yellowstone National Park as potential analogs to Archean continental surfaces. Hydrothermal sub-sinter environments provide ideal conditions for phototrophic microbial communities, including blocking of harmful UV radiation, trapping and retention of moisture, and protection from erosion by rain and surface runoff. Hypolithic communities in geothermal settings were similar in both composition and carbon uptake rates to nearby hot spring communities. We hypothesize that hydrothermal area hypolithic communities represent modern analogs of phototrophic microbial communities that colonized Archean continental surfaces, producing oxygen locally and facilitating microbially-mediated pyrite oxidation prior to the presence of free oxygen in the global atmosphere. These results have implications for oxidation of the early Earth surface, the search for biosignatures in the rock record, as well as for potential harbors of past life on Mars and the search for life on Exoplanets.

  13. Correlation between surface reconstruction and polytypism in InAs nanowire selective area epitaxy

    Science.gov (United States)

    Liu, Ziyang; Merckling, Clement; Rooyackers, Rita; Richard, Olivier; Bender, Hugo; Mols, Yves; Vila, María; Rubio-Zuazo, Juan; Castro, Germán R.; Collaert, Nadine; Thean, Aaron; Vandervorst, Wilfried; Heyns, Marc

    2017-12-01

    The mechanism of widely observed intermixing of wurtzite and zinc-blende crystal structures in InAs nanowire (NW) grown by selective area epitaxy (SAE) is studied. We demonstrate that the crystal structure in InAs NW grown by SAE can be controlled using basic growth parameters, and wurtzitelike InAs NWs are achieved. We link the polytypic InAs NWs SAE to the reconstruction of the growth front (111)B surface. Surface reconstruction study of InAs (111) substrate and the following homoepitaxy experiment suggest that (111) planar defect nucleation is related to the (1 × 1) reconstruction of InAs (111)B surface. In order to reveal it more clearly, a model is presented to correlate growth temperature and arsenic partial pressure with InAs NW crystal structure. This model considers the transition between (1 × 1) and (2 × 2) surface reconstructions in the frame of adatom atoms adsorption/desorption, and the polytypism is thus linked to reconstruction quantitatively. The experimental data fit well with the model, which highly suggests that surface reconstruction plays an important role in the polytypism phenomenon in InAs NWs SAE.

  14. Sensitive and selective analysis of a wide concentration range of IGFBP7 using a surface plasmon resonance biosensor.

    Science.gov (United States)

    Jang, Dae-Ho; Choi, Youngbo; Choi, Yong-Soo; Kim, Sun-Mi; Kwak, Hojung; Shin, Se-Hyun; Hong, Surin

    2014-11-01

    A sensitive method for selectively detecting insulin-like growth factor-binding protein 7 (IGFBP7) over a wide range of concentrations based on the surface plasmon resonance (SPR) biosensing techniques is described. IGFBP7 has been shown to regulate cell proliferation, cell adhesion, cellular senescence, apoptosis, and angiogenesis in several different cancer cell lines. Since the concentration of IGFBP7 can vary widely in the body, determining the precise concentration of IGFBP7 over a wide range of concentrations is important, since it serves as an inducible biomarker for both disease diagnosis and subsequent therapy. The SPR sensing method is based on the selective interaction of IGFBP7 with specific anti-IGFBP7 proteins on a gold thin film, which was covalently bound to the Fc-binding domain of protein G on a mixed self-assembled monolayer composed of DSNHS (S2(CH2)11COO(CH2)2COO-(N-hydroxysuccinimide)) and mercaptoundecanol, and effect of this on changes in the SPR profiles. The limit of detection (LOD) of the SPR biosensor was determined to be 10 ng/ml, which is a reasonable LOD value for biomedical applications. The response is essentially linear in the concentration range of 10-300 ng/ml. The SPR biosensor also shows specificity for IGFBP7 compared to that for biologically relevant interleukin (IL) derivatives including IL4, IL23, IL29, and IFG1. These molecules are also present along with IGFBP7 in the cell culture medium and have the potential to interfere with the analysis. Finally, the level secretion of IGFBP7 from cancer cells detected by the SPR biosensor showed a good correlation with a commercial kit using an IGFBP7 enzyme-linked immunosorbent assay. The findings reported herein indicate that the SPR biosensor for IGFBP7 would be applicable in a wide variety of biomedical fields. Copyright © 2014 Elsevier B.V. All rights reserved.

  15. Secondary shock features for large surface explosions: results from the Sayarim Military Range, Israel and other experiments

    Science.gov (United States)

    Gitterman, Y.

    2014-05-01

    A series of surface explosions was designed and conducted by the Geophysical Institute of Israel at the Sayarim Military Range in the Negev desert, including two large-scale explosions: approx. 82 tons of high explosives in 2009, and approx. 100 tons of low-grade ANFO explosives in 2011. The main goal of the explosions was to provide large controlled sources for calibration of global infrasound stations designated for monitoring nuclear tests; however, the geophysical experiment also provided valuable observations for shock wave research. High-pressure gauges were deployed at distances between 100 and 600 m to record air blast properties and to provide reliable estimation of the true charge yield compared to the design value. Secondary shock phenomena were clearly observed at all near-source gauges as characteristic shock wave shapes. Secondary shocks were also observed at numerous seismic and acoustic sensors deployed in the range 0.3-20 km as acoustic phases. Empirical relationships for standard air blast parameters (peak pressure and impulse) and for a new parameter called secondary shock time delay, as a function of distance, were established and analyzed. The standard parameters, scaled by the cubic root of the estimated TNT yield, were found to be consistent for all analyzed explosions. However, the scaled secondary shock delays were clearly separated for the 2009 and 2011 explosions, thus demonstrating dependence on the explosive type. Additionally, air blast records from other experiments were used to extend the charge and distance ranges for the secondary shock observation, and showed consistency with the Sayarim data. Analysis and interpretation of observed features of the secondary shock phenomenon are proposed and a new empirical relationship of scaled secondary shock delay versus scaled distance is established. The results suggest that the secondary shock delay can be used as a new additional waveform feature for simple and cost-effective explosive

  16. Corrective Action Decision Document for Corrective Action Unit 417: Central Nevada Test Area Surface, Nevada

    International Nuclear Information System (INIS)

    1999-01-01

    This Corrective Action Decision Document (CADD) identifies and rationalizes the U.S. Department of Energy, Nevada Operations Office's selection of a recommended corrective action alternative (CAA) appropriate to facilitate the closure of Corrective Action Unit (CAU) 417: Central Nevada Test Area Surface, Nevada, under the Federal Facility Agreement and Consent Order. Located in Hot Creek Valley in Nye County, Nevada, and consisting of three separate land withdrawal areas (UC-1, UC-3, and UC-4), CAU 417 is comprised of 34 corrective action sites (CASs) including 2 underground storage tanks, 5 septic systems, 8 shaker pad/cuttings disposal areas, 1 decontamination facility pit, 1 burn area, 1 scrap/trash dump, 1 outlier area, 8 housekeeping sites, and 16 mud pits. Four field events were conducted between September 1996 and June 1998 to complete a corrective action investigation indicating that the only contaminant of concern was total petroleum hydrocarbon (TPH) which was found in 18 of the CASs. A total of 1,028 samples were analyzed. During this investigation, a statistical approach was used to determine which depth intervals or layers inside individual mud pits and shaker pad areas were above the State action levels for the TPH. Other related field sampling activities (i.e., expedited site characterization methods, surface geophysical surveys, direct-push geophysical surveys, direct-push soil sampling, and rotosonic drilling located septic leachfields) were conducted in this four-phase investigation; however, no further contaminants of concern (COCs) were identified. During and after the investigation activities, several of the sites which had surface debris but no COCs were cleaned up as housekeeping sites, two septic tanks were closed in place, and two underground storage tanks were removed. The focus of this CADD was to identify CAAs which would promote the prevention or mitigation of human exposure to surface and subsurface soils with contaminant

  17. Investigation on the growth of DAST crystals of large surface area for THz applications

    International Nuclear Information System (INIS)

    Vijay, R. Jerald; Melikechi, N.; Thomas, Tina; Gunaseelan, R.; Arockiaraj, M. Antony; Sagayaraj, P.

    2012-01-01

    Graphical abstract: It is evident from the photographs that the crystal tend to grow as a needle (Fig. 1a) in the lower concentration region (2–3 g/200 mL); whereas, in the high concentration region (5 g/200 mL) though there is a marked enlargement in the size of the crystal, the morphology of the resulting DAST crystal is slightly irregular (Fig. 1d) in nature. Among the four concentrations employed, best result was obtained with the DAST–methanol solution of concentration 4 g/200 mL; which resulted in the DAST crystal of large surface area (270 mm 2 ) with high transparency and nearly square shape (Fig. 1c) in a growth period of 20–25 days. Highlights: ► DAST crystals of different sizes are obtained for different concentrations. ► The main focus is to grow DAST crystals with large surface area. ► Structural, optical, thermal and mechanical properties are investigated. - Abstract: The growth of high quality 4-N,N-dimethylamino-4-N-methyl-stilbazoliumtosylate (DAST) crystal with large surface area is reported by adopting the slope nucleation coupled slow evaporation method (SNM-SE). The structure and composition of the crystal are studied by single crystal X-ray diffraction and CHN analyses. The linear optical properties are investigated by UV–vis absorption. The melting point and thermal behavior of DAST are investigated using differential scanning calorimetric (DSC) and thermogravimetric analyses (TGA). The Vickers microhardness number (VHN) and work hardening coefficient of the grown crystal have been determined. The surface features of the DAST crystal are analyzed by scanning electron microscopy (SEM) and it confirmed the presence of narrow line defects (NLDs) in the sample.

  18. Clay Mineralogy Studies of Soils Located on Different Geomorphic Surfaces in Jabalbarez-Jiroft Area

    Directory of Open Access Journals (Sweden)

    naser boroumand

    2017-02-01

    Full Text Available Introduction: Soil and geomorphology are closely related to each other. That is why considering geomorphic concepts in soil genesis and classification studies may cause a better understanding of soil genesis processes. Paleosols with argillic horizons were investigated on stable pediment surfaces in Jiroft area, central Iran, by Sanjari et al. (2011. They found that secondary gypsum and calcium carbonate were accumulated in mantled pediments, but moving down the slope toward lowlands, salts more soluble than gypsum have been accumulated. Clay mineralogy in soil researches helps to better studying soil genesis and development. A quantitative and qualitative study of clay minerals together with their structural composition provides valuable data on the absorption, fixation, and desorption of different cations in soils. Smectite, chlorite, illite, vermiculite, kaolinite, palygorskite, and sepiolite were reported as dominant clay minerals found in arid and semi-arid areas. The objectives of the present study are to evaluate the clay mineralogy of Jabalbarez-Jiroft soils on different geomorphic surfaces. Materials and Methods: The study area was located in Jabalbarez, 200 Km south Kerman, Central Iran. Fig. 1 showed the exact location of study area. Soil temperature and moisture regimes of the area were thermic and aridic, respectively. Hill, rock pediment, mantled pediment and piedmont alluvial plain landforms were identified, using aerial photo interpretation, topography and geological map observation, in addition to detailed field works. Air-dried soil samples were crushed and passed through a 2-mm sieve. Routine physicochemical analyses wereperformed on the samples. Undisturbed soil samples from the Bt horizon of pedons 4, 5 and 6 were chosen for micromorphology investigations. Beside, eight samples including A and C2 horizons of pedon 1, A and Bt horizon of pedon 3, Bt and Bw horizons of pedon 4, and Bt and C horizon of pedon 5 were selected for

  19. Recent and historical range shifts of two canopy-forming seaweeds in North Spain and the link with trends in sea surface temperature

    Science.gov (United States)

    Duarte, Linney; Viejo, Rosa M.; Martínez, Brezo; deCastro, Maite; Gómez-Gesteira, Moncho; Gallardo, Tomás

    2013-08-01

    Geographical range shifts of two canopy-forming seaweeds, Himanthalia elongata (L.) S.F. Gray and Fucus serratus L. were investigated at their southern range boundary in Northern Spain from the end of nineteenth century to 2009. Given the good dispersal abilities of H. elongata and its short life-span, we hypothesize that this species will track environmental changes at a faster rate than the perennial and short-distance disperser F. serratus. Our results show a continuous and drastic westward retraction of H. elongata, which has nowadays virtually vanished in Northern Spain, whereas F. serratus is still found in the westernmost area. Despite this, the first species is still relatively abundant in the Iberian Peninsula, whereas the presence of the latter is scattered and reduced. Overall, range shifts fit with the warming trend in sea surface temperature (SST), whereas it is unlikely that increases in grazing pressure or coastal pollution have driven the observed changes, particularly the rapid trend in recent years. Differences in species traits are linked to range dynamics. The higher persistence of F. serratus at eastern shores may thus be related to its longer life span and its greater thermal tolerance. The presence of sporadic populations of H. elongata outside the zone of continuous distribution can be attributed to long-distance dispersal events during cold pulses. Relict populations in isolated and estuarine locations were left behind in the contracting range margins, particularly for F. serratus. In Northern Spain, the westward retreat of large canopy-forming algae seems to be a general phenomenon, involving other species such as kelps. Therefore, an evident reorganization of coastal assemblages is expected, though the temporal extent of changes and the consequences for ecosystem services need to be evaluated.

  20. Highly exposed surface area of {001} facets dominated BiOBr nanosheets with enhanced visible light photocatalytic activity.

    Science.gov (United States)

    Duan, Fang; Wang, Xiaofeng; Tan, Tingting; Chen, Mingqing

    2016-02-17

    Two groups of BiOBr nanosheets with different sizes and similar exposure percentages of {001} facets were selectively synthesized by simple hydrothermal methods. The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and UV-vis diffuse reflectance spectroscopy (DRS). The photocatalytic activity was estimated from the degradation of organic pollutants under visible-light irradiation. The results indicated that BiOBr nanosheets with similar exposure percentages of {001} facets but smaller sizes exhibited higher photocatalytic activity. Furthermore, the effects of the size, including the thickness and length, of BiOBr nanosheets were also studied. The results showed that the impact of thickness was more significant than that of length. It was found that reducing the thickness of BiOBr nanosheets can significantly increase the exposed surface areas of {001} facets (S{001}), but not necessarily the exposure percentage of {001} facets. Moreover, in our experiment, the photocatalytic activity of BiOBr nanosheets increased linearly with an increase in S{001} in the range of 0.022 to 0.111 nm(-1). Therefore, the photocatalytic activity of BiOBr nanosheets depended on the exposed surface areas of {001} facets rather than the exposure percentage of {001} facets. The enhancement of the photocatalytic activity of ultrathin BiOBr nanosheets with large exposed surface areas of {001} facets can be mainly ascribed to their enhanced absorption of visible light and improved separation efficiency of charge carriers.

  1. Dose of dialysis based on body surface area is markedly less in younger children than in older adolescents.

    Science.gov (United States)

    Daugirdas, John T; Hanna, Melisha G; Becker-Cohen, Rachel; Langman, Craig B

    2010-05-01

    BACKGROUND AND OBSERVATIONS: The current denominator for dosing dialysis is the urea distribution volume (V). Normalizing Kt/V to body surface area (S) has been proposed, but the implications of doing this in children have not been examined. Dialysis dose given to children and adolescents was calculated in terms of conventional V-based scaling and surface-area-normalized standard Kt/V (SAN-stdKt/V) calculated as stdKt/V x (Vant/S)/17.5, where Vant was an anthropometric estimate of V calculated using the Morgenstern equation. Formal 2-pool modeling was used to compute all dialysis adequacy outputs. In 34 children (11 girls, 23 boys) dialyzed 3 times a week, age range 1.4 to 18 years, the mean delivered equilibrated Kt/V (eKt/V) was 1.40, and the mean stdKt/V was 2.49, both of which tended to be higher in younger children. The ratio of Vant to S was 15.6 +/- 2.69 and was strongly associated with age between ages 2 and 16. SAN-stdKt/V averaged 2.21 and was strongly correlated with age between ages 2 and 16. If one considers a desired target for SAN-stdKt/V to be 2.45, all children less than 10 years of age were below target, despite having relatively high values of eKt/V and stdKt/V. If a surface-area-based denominator were to be adopted for dialysis dosing, most children under 10 years of age would receive markedly less dialysis than adolescent patients and would require 6- to 8-hour hemodialysis sessions or, for the youngest children, treatments given more frequently than 3 times/wk.

  2. Influence of Alkali Treatment on the Surface Area of Aluminium Dross

    Directory of Open Access Journals (Sweden)

    N. S. Ahmad Zauzi

    2016-01-01

    Full Text Available Aluminium dross is an industrial waste from aluminium refining industry and classified as toxic substances. However, the disposal of dross as a waste is a burden to aluminium manufacturer industries due to its negative effects to the ecosystem, surface, and ground water. Therefore the purpose of this study is to evaluate the influence of sodium hydroxide (NaOH on the surface area and pore size of aluminium dross. There were 3 stages in the treatment activities, which were leaching, precipitation, and calcination process. The optimum result from this study was the surface area of aluminium dross increases from 10.1 m2/g up to 80.0 m2/g at 40°C, 1% NaOH, and 15-minute reaction time. Thus, aluminium dross has a potential to be converted into other useful material such as catalyst and absorbent. The benefit of this research is that the hazardous industrial waste can be turned into wealth to be used in other applications such as in catalytic activities and absorber in waste water treatment. Further investigation on the physicochemical of aluminium dross with different acid or alkali should be conducted to get deeper understanding on the aluminium dross as a catalyst-type material.

  3. Assessment of mercury erosion by surface water in Wanshan mercury mining area.

    Science.gov (United States)

    Dai, ZhiHui; Feng, Xinbin; Zhang, Chao; Shang, Lihai; Qiu, Guangle

    2013-08-01

    Soil erosion is a main cause of land degradation, and in its accelerated form is also one of the most serious ecological environmental problems. Moreover, there are few studies on migration of mercury (Hg) induced by soil erosion in seriously Hg-polluted districts. This paper selected Wanshan Hg mining area, SW China as the study area. Revised universal soil loss equation (RUSLE) and Geographic information system (GIS) methods were applied to calculate soil and Hg erosion and to classify soil erosion intensity. Our results show that the soil erosion rate can reach up to 600,884tkm(-2)yr(-1). Surfaces associated with very slight and extremely severe erosion include 76.6% of the entire land in Wanshan. Furthermore, the cumulative erosion rates in the area impacted by extremely severe erosion make up 90.5% of the total. On an annual basis, Hg surface erosion load was predicted to be 505kgyr(-1) and the corresponding mean migration flux of Hg was estimated to be 3.02kgkm(-2)yr(-1). The erosion loads of Hg resulting from farmland and meadow soil were 175 and 319kgyr(-1) respectively, which were enhanced compared to other landscape types due to the fact that they are generally located in the steep zones associated with significant reclamation. Contributing to establish a mass balance of Hg in Wanshan Hg mining area, this study supplies a dependable scientific basis for controlling soil and water erosion in the local ecosystems. Land use change is the most effective way for reducing Hg erosion load in Wanshan mining area. Copyright © 2013 Elsevier Inc. All rights reserved.

  4. Surface deformation of active volcanic areas retrieved with the SBAS-DInSAR technique: an overview

    Directory of Open Access Journals (Sweden)

    G. Zeni

    2008-06-01

    Full Text Available This paper presents a comprehensive overview of the surface deformation retrieval capability of the Differential Synthetic Aperture Radar Interferometry (DInSAR algorithm, referred to as Small BAseline Subset (SBAS technique, in the context of active volcanic areas. In particular, after a brief description of the algorithm some experiments relevant to three selected case-study areas are presented. First, we concentrate on the application of the SBAS algorithm to a single-orbit scenario, thus considering a set of SAR data composed by images acquired on descending orbits by the European Remote Sensing (ERS radar sensors and relevant to the Long Valley caldera (eastern California area. Subsequently, we address the capability of the SBAS technique in a multipleorbit context by referring to Mt. Etna volcano (southern Italy test site, with respect to which two different ERS data set, composed by images acquired both on ascending and descending orbits, are available. Finally, we take advantage of the capability of the algorithm to work in a multi-platform scenario by jointly exploiting two different sets of SAR images collected by the ERS and the Environment Satellite (ENVISAT radar sensors in the Campi Flegrei caldera (southern Italy area. The presented results demonstrate the effectiveness of the algorithm to investigate the deformation field in active volcanic areas and the potential of the DInSAR methodologies within routine surveillance scenario.

  5. Visualization of Lake Mead Surface Area Changes from 1972 to 2009

    Directory of Open Access Journals (Sweden)

    David M. Atkinson

    2012-06-01

    Full Text Available For most of the last decade, the south-western portion of the United States has experienced a severe and enduring drought. This has caused serious concerns about water supply and management in the region. In this research, 30 orthorectified Landsat satellite images from the United States Geological Service (USGS Earth Explorer archive were analyzed for the 1972 to 2009 period. The images encompassed Lake Mead (a major reservoir in this region and were examined for changes in water surface area. Decadal lake area minimums/maximums were achieved in 1972/1979, 1981/1988, 1991/1998, and 2009/2000. The minimum lake area extent occurred in 2009 (356.4 km2, while the maximum occurred in 1998 (590.6 km2. Variable trends in water level and lake area were observed throughout the analysis period, however progressively lower values were observed since 2000. The Landsat derived lake areas show a very strong relationship with actual measured water levels at the Hoover Dam. Yearly water level variations at the dam vary minimally from the satellite derived estimates. A complete (yearly record of satellite images may have helped to reduce the slight deviations in the time series.

  6. Estimating Surface Area of Sponges and Marine Gorgonians as Indicators of Habitat Availability on Caribbean Coral Reefs

    Science.gov (United States)

    Surface area and topographical complexity are fundamental attributes of shallow tropical coral reefs and can be used to estimate habitat for fish and invertebrates. This study presents empirical methods for estimating surface area provided by sponges and gorgonians in the Central...

  7. Groundwater impact on surface water quality and nutrient loads in lowland polder catchments: monitoring the greater Amsterdam area

    NARCIS (Netherlands)

    Yu, L.; Rozemeijer, J.; Breukelen, B.M. van; Ouboter, M.; Vlugt, C. van der; Broers, H.P.

    2018-01-01

    The Amsterdam area, a highly manipulated delta area formed by polders and reclaimed lakes, struggles with high nutrient levels in its surface water system. The polders receive spatially and temporally variable amounts of water and nutrients via surface runoff, groundwater seepage, sewer leakage, and

  8. Groundwater impacts on surface water quality and nutrient loads in lowland polder catchments : Monitoring the greater Amsterdam area

    NARCIS (Netherlands)

    Yu, Liang; Rozemeijer, Joachim; van Breukelen, B.M.; Ouboter, Maarten; Van Der Vlugt, Corné; Broers, Hans Peter

    2018-01-01

    The Amsterdam area, a highly manipulated delta area formed by polders and reclaimed lakes, struggles with high nutrient levels in its surface water system. The polders receive spatially and temporally variable amounts of water and nutrients via surface runoff, groundwater seepage, sewer leakage,

  9. Atomic layer deposition of highly dispersed Pt nanoparticles on a high surface area electrode backbone for electrochemical promotion of catalysis

    NARCIS (Netherlands)

    Hajar, Y.; di Palma, V.; Kyriakou, V.; Verheijen, M. A.; Baranova, E. A.; Vernoux, P.; Kessels, W. M. M.; Creatore, M.; van de Sanden, M. C. M.; Tsampas, M. N.

    2017-01-01

    A novel catalyst design for electrochemical promotion of catalysis (EPOC) is proposed which overcomes the main bottlenecks that limit EPOC commercialization, i.e., the low dispersion and small surface area of metal catalysts. We have increased the surface area by using a porous composite electrode

  10. NEW RANGE LIMIT OF THE ANOPETIA GOUNELLEI (AVES: TROCHILIDAE: STATE OF ART AND A REVIEW ON THE UPDATED AREA

    Directory of Open Access Journals (Sweden)

    ERICA CSEKÖ NOLASCO

    Full Text Available ABSTRACT New technologies and the rapid amount of data help to improve and update the distribution of the species. Anopetia gounellei (Broad-tipped Hermit, Trochilidae is a poorly known hummingbird and has been recorded outside its formal range since 2009. Here we reviewed the records of the Broad-tipped Hermit, proposing new range limits and discussing the species ecoregional endemism. The species was recorded in a variety of vegetation, including caatinga and humid forest. Our updated range-limit suggest an increase of 80% from the previous range, exceeding the Caatinga limits, calling into question the endemism of the species to this biome, but confirming a close relationship with dry ecoregions in Brazil. Basic information about its biology is needed, and further studies about breeding and ecological requirements are recommended.

  11. Minimal area surfaces in AdS n+1 and Wilson loops

    Science.gov (United States)

    He, Yifei; Huang, Changyu; Kruczenski, Martin

    2018-02-01

    The AdS/CFT correspondence relates the expectation value of Wilson loops in N = 4 SYM to the area of minimal surfaces in AdS 5. In this paper we consider minimal area surfaces in generic Euclidean AdS n+1 using the Pohlmeyer reduction in a similar way as we did previously in Euclidean AdS 3. As in that case, the main obstacle is to find the correct parameterization of the curve in terms of a conformal parameter. Once that is done, the boundary conditions for the Pohlmeyer fields are obtained in terms of conformal invariants of the curve. After solving the Pohlmeyer equations, the area can be expressed as a boundary integral involving a generalization of the conformal arc-length, curvature and torsion of the curve. Furthermore, one can introduce the λ-deformation symmetry of the contours by a simple change in the conformal invariants. This determines the λ-deformed contours in terms of the solution of a boundary linear problem. In fact the condition that all λ deformed contours are periodic can be used as an alternative to solving the Pohlmeyer equations and is equivalent to imposing the vanishing of an infinite set of conserved charges derived from integrability.

  12. Monitoring of the Earth's surface deformation in the area of water dam Zarnowiec

    Science.gov (United States)

    Mojzes, Marcel; Wozniak, Marek; Habel, Branislav; Macak, Marek

    2017-04-01

    Mathematical and physical research directly motivates geodetic community which can provide very accurate measurements for testing of the proposed models Earth's surface motion near the water dams should be monitored due to the security of the area. This is a process which includes testing of existing models and their physical parameters. Change of the models can improve the practical results for analyzing the trends of motion in the area of upper reservoir of water dam Zarnowiec. Since 1998 Warsaw University of Technology realized a research focused on the horizontal displacements of the upper reservoir of water dam Zarnowiec. The 15 selected control points located on the upper reservoir crown of the water dam were monitored by classical distance measurements. It was found out that changes in the object's geometry occur due to the variation of the water level. The control measurements of the changes in the object's geometry occurring during the process of emptying and filling of the upper reservoir of water dam were compared with the deformations computed using improved Boussinesqués method programmed in the software MATLAB and ANSYS for elastic and isotropic half space as derivation of suitable potentials extended to the loaded region. The details and numerical results of this process are presented This presentation was prepared within the project "National Centre for Diagnostic of the Earth's Surface Deformations in the Area of Slovakia", ITMS code: 26220220108.

  13. The importance of the active surface area of graphite materials in the first lithium intercalation

    Energy Technology Data Exchange (ETDEWEB)

    Novak, P.; Ufheil, J.; Buqa, H. [Paul Scherrer Institut, Electrochemistry Laboratory, CH-5232 Villigen PSI (Switzerland); Krumeich, F. [ETH Zuerich, Laboratory of Inorganic Chemistry, CH-8093 Zurich (Switzerland); Spahr, M.E.; Goers, D.; Wilhelm, H.; Vix-Guterl, C. [TIMCAL SA, CH-6743 Bodio TI (Switzerland); Dentzer, J.; Gadiou, R. [Institut de Chimie des Surfaces et Interfaces, CNRS UPR 9069, F-68057 Mulhouse Cedex (France)

    2007-12-06

    When lithium is intercalated into graphite in ethylene carbonate (EC) containing electrolytes, solvent co-intercalation leading to the exfoliation of the graphite structure could occur. The exfoliation can be suppressed if an efficient solid electrolyte interphase (SEI, a passivation layer) is formed. Here we study the role played by the active surface area (ASA) of graphite materials during their first electrochemical reduction. ASA (related to the presence of defects at the carbon surface) appears as a critical graphite surface parameter influencing the surface passivation mechanism and the graphite exfoliation. The ASA of TIMREX {sup registered} SLX50 synthetic graphite was modified by thermal treatment in argon and air. The electrochemical performance was characterized in 1 M LiPF{sub 6}, EC:DMC electrolyte and post mortem analyses were performed by SEM imaging. It turned out that a decrease of the graphite ASA, i.e., an increase of the graphite structural order, hinders the formation of the passivation layer and favors the exfoliation process. In contrast, the exfoliation of the same graphite can be suppressed if its ASA is increased for example by air treatment. The ASA of the graphite kinetically controls the formation of an efficient SEI film and accordingly the irreversible charge loss is much lower in the case of graphite with a high ASA value. (author)

  14. Blasting injuries in surface mining with emphasis on flyrock and blast area security

    Energy Technology Data Exchange (ETDEWEB)

    Bajpayee, T.S.; Rehak, T.R.; Mowrey, G.L.; Ingram, D.K. [NIOSH, Pittsburgh, PA (USA). Pittsburgh Research Lab.

    2004-07-01

    Blasting is a hazardous component of surface mining. Serious injuries and fatalities result from improper judgment or practice during rock blasting. This paper describes several fatal injury case studies, analyzes causative factors, and emphasizes preventive measures. During the 21-year period from 1978 to 1998, the mean yearly explosive-related injuries (fatal and nonfatal) for surface coal mines was 8.86 (95% CI: 6.38-11.33), and for surface metal/nonmetal mines 10.76 (95% CI: 8.39-13.14). Flyrock and lack of blast area security accounted for 68.2% of these injuries. Case studies indicate that the causative factors for fatal injuries are primarily personal and task-related and to some extent environmental. A reduction in the annual injuries in surface coal mines was observed during the 10-year period of 1989-1998 (5.80 (95% CI: 2.71-8.89)) compared to the previous 10-year period of 1979-1988 (10.90 (95% CI: 7.77-14.14)). However, such reduction was not noticed in the metal/nometal sector (i.e., 9.30 (95% CI: 6.84-11.76) for the period 1989-1998 compared with 11.00 (95% CI: 7.11-14.89) for the period 1979-1988). Discussion of case studies during safety meetings will help to mitigate fatal injuries and derive important payoffs in terms of lower risks and costs of injuries.

  15. Analysis and Application of River Surface Line in Hilly Area based on Hec-ras Model

    Directory of Open Access Journals (Sweden)

    Yang Congshan

    2017-01-01

    Full Text Available For example—Cixian Fuyang River Regulation Project. Due to the character that Fuyang River is located in hilly areas of Cixian, we use the Hex-ras software to calculate the status of the river water surface line for the goal of determining the final treatment plan. We maintain the present situation of the river channel design as principle, select the most appropriate pushed water level and roughnessas the basic, and we combine the classification calculation of crossing structures of backwater and the encryption calculation section to get the more accurate result. We compare the water level elevation and the calculation of cross strait, analyze the design parameters, calculate repeated the water line section, analyze the rationality of the design plan, and then finally determine the applicability of Hex-rac software in the large continuous variation of cross section of embankment of river river surface line.

  16. Dissolution Effects on Specific Surface Area, Particle Size, and Porosity of Pentelic Marble.

    Science.gov (United States)

    Orkoula, Malvina G.; Koutsoukos, Petros G.

    2001-07-15

    Dissolution of natural stone such as marble is not limited to its surface. The porous structure, known to play an important role in stone decay, is also affected by the conditions of dissolution. In the present work, the changes in pore size distribution of Pentelic marble particles accompanying chemical dissolution in undersaturated solutions and at alkaline pH 8.25 were investigated. The specific surface area and the mesopore distribution of the Pentelic marble tested showed a pronounced decrease to very low values. On the other hand, the sizes of macropores exhibited a tendency to increase with the extent of dissolution due either to dissolution in the interior of the pores or to fusion of small pores into larger. Furthermore, the number of small particles decreased significantly, reaching complete disappearance, depending on the extent of dissolution. At the same time, the relative number of particles of intermediate size increased. Copyright 2001 Academic Press.

  17. GC/MS Analysis of Pesticides in the Ferrara Area (Italy) Surface Water: A Chemometric Study

    International Nuclear Information System (INIS)

    Pasti, L.; Dondi, F.; Nava, E.; Morelli, M.; Bignami, S.

    2007-01-01

    The development of a network to monitor surface waters is a critical element in the assessment, restoration and protection of water quality. In this study, concentrations of 42 pesticides - determined by GC-MS on samples from 11 points along the Ferrara area rivers - have been analyzed by chemometric tools. The data were collected over a three-year period (2002-2004). Principal component analysis of the detected pesticides was carried out in order to define the best spatial locations for the sampling points. The results obtained have been interpreted in view of agricultural land use. Time series data regarding pesticide contents in surface waters has been analyzed using the Autocorrelation function. This chemometric tool allows for seasonal trends and makes it possible to optimize sampling frequency in order to detect the effective maximum pesticide content

  18. Adsorption of neon and tetrafluoromethane on carbon nanohorn aggregates: differences in specific surface area values

    Science.gov (United States)

    Krungleviciute, Vaiva; Yudasaka, Masako; Iijima, Sumio; Migone, Aldo

    2008-03-01

    We have measured adsorption isotherms for two different adsorbates, neon and tetrafluoromethane, on dahlia-like carbon nanohorn aggregates. The experiments were performed at similar relative temperatures for both gases. The measurements were conducted to explore the effect of adsorbate diameter on the behavior of the resulting adsorbed systems. We measured the effective specific surface area value of the nanohorn sample using both gases, and we found that this quantity was about 22% smaller when we determined this quantity using tetrafluoromethane, the larger molecule. Isosteric heat and binding energy values were also determined from our measurements. We will compare our experimental results with those from a computer simulation study performed by Prof. M. Calbi. The simulations help us understand the source of the observed differences in the measured specific surface values, as well as the coverage dependence of the isosteric heat of adsorption for both gases.

  19. Tuning Porosity and Surface Area in Mesoporous Silicon for Application in Li-Ion Battery Electrodes.

    Science.gov (United States)

    Cook, John B; Kim, Hyung-Seok; Lin, Terri C; Robbennolt, Shauna; Detsi, Eric; Dunn, Bruce S; Tolbert, Sarah H

    2017-06-07

    This work aims to improve the poor cycle lifetime of silicon-based anodes for Li-ion batteries by tuning microstructural parameters such as pore size, pore volume, and specific surface area in chemically synthesized mesoporous silicon. Here we have specifically produced two different mesoporous silicon samples from the magnesiothermic reduction of ordered mesoporous silica in either argon or forming gas. In situ X-ray diffraction studies indicate that samples made in Ar proceed through a Mg 2 Si intermediate, and this results in samples with larger pores (diameter ≈ 90 nm), modest total porosity (34%), and modest specific surface area (50 m 2 g -1 ). Reduction in forming gas, by contrast, results in direct conversion of silica to silicon, and this produces samples with smaller pores (diameter ≈ 40 nm), higher porosity (41%), and a larger specific surface area (70 m 2 g -1 ). The material with smaller pores outperforms the one with larger pores, delivering a capacity of 1121 mAh g -1 at 10 A g -1 and retains 1292 mAh g -1 at 5 A g -1 after 500 cycles. For comparison, the sample with larger pores delivers a capacity of 731 mAh g -1 at 10 A g -1 and retains 845 mAh g -1 at 5 A g -1 after 500 cycles. The dependence of capacity retention and charge storage kinetics on the nanoscale architecture clearly suggests that these microstructural parameters significantly impact the performance of mesoporous alloy type anodes. Our work is therefore expected to contribute to the design and synthesis of optimal mesoporous architectures for advanced Li-ion battery anodes.

  20. Improved capacity to evaluate changes in intestinal mucosal surface area using mathematical modeling.

    Science.gov (United States)

    Greig, Chasen J; Cowles, Robert A

    2017-07-01

    Quantification of intestinal mucosal growth typically relies on morphometric parameters, commonly villus height, as a surrogate for presumed changes in mucosal surface area (MSA). We hypothesized that using mathematical modeling based on multiple unique measurements would improve discrimination of the effects of interventions on MSA compared to standard measures. To determine the ability of mathematical modeling to resolve differences in MSA, a mouse model with enhanced serotonin (5HT) signaling known to stimulate mucosal growth was used. 5-HT signaling is potentiated by targeting the serotonin reuptake transporter (SERT) molecule. Selective serotonin reuptake inhibitor-treated wild-type (WT-SSRI), SERT-knockout (SERTKO), and wild-type C57Bl/6 (WT) mice were used. Distal ileal sections were H&E-stained. Villus height (VH), width (VW), crypt width (CW), and bowel diameter were used to calculate surface area enlargement factor (SEF) and MSA. VH alone for SERTKO and SSRI was significantly increased compared to WT, without a difference between SERTKO and WT-SSRI. VW and CW were significantly decreased for both SERTKO and WT-SSRI compared to WT, and VW for WT-SSRI was also decreased compared to SERTKO. These changes increased SEF and MSA for SERTKO and WT-SSRI compared to WT. Additionally, SEF and MSA were significantly increased for WT-SSRI compared to SERTKO. Mathematical modeling provides a valuable tool for differentiating changes in intestinal MSA. This more comprehensive assessment of surface area does not appear to correlate linearly with standard morphometric measures and represents a more comprehensive method for discriminating between therapies aimed at increasing functional intestinal mucosa. © 2017 Wiley Periodicals, Inc.