A simple experimental setup for magneto-dielectric measurements

International Nuclear Information System (INIS)

Manimuthu, P.; Shanker, N. Praveen; Kumar, K. Saravana; Venkateswaran, C.

2014-01-01

The increasing demand for the multiferroic materials calls for the need of an experimental setup that will facilitate magneto-dielectric coupling measurements. A connector setup designed makes it possible to measure and analyze the dielectric properties of the material under the influence of a magnetic field. The salient feature of this setup is in its incorporation with the already existing experimental facilities

An experimental test facility to support development of the fluoride-salt-cooled high-temperature reactor

International Nuclear Information System (INIS)

Yoder, Graydon L.; Aaron, Adam; Cunningham, Burns; Fugate, David; Holcomb, David; Kisner, Roger; Peretz, Fred; Robb, Kevin; Wilgen, John; Wilson, Dane

2014-01-01

Highlights: • • A forced convection test loop using FLiNaK salt was constructed to support development of the FHR. • The loop is built of alloy 600, and operating conditions are prototypic of expected FHR operation. • The initial test article is designed to study pebble bed heat transfer cooled by FLiNaK salt. • The test facility includes silicon carbide test components as salt boundaries. • Salt testing with silicon carbide and alloy 600 confirmed acceptable loop component lifetime. - Abstract: The need for high-temperature (greater than 600 °C) energy transport systems is significantly increasing as the world strives to improve energy efficiency and develop alternatives to petroleum-based fuels. Liquid fluoride salts are one of the few energy transport fluids that have the capability of operating at high temperatures in combination with low system pressures. The fluoride-salt-cooled high-temperature reactor design uses fluoride salt to remove core heat and interface with a power conversion system. Although a significant amount of experimentation has been performed with these salts, specific aspects of this reactor concept will require experimental confirmation during the development process. The experimental facility described here has been constructed to support the development of the fluoride-salt-cooled high-temperature reactor concept. The facility is capable of operating at up to 700 °C and incorporates a centrifugal pump to circulate FLiNaK salt through a removable test section. A unique inductive heating technique is used to apply heat to the test section, allowing heat transfer testing to be performed. An air-cooled heat exchanger removes added heat. Supporting loop infrastructure includes a pressure control system, a trace heating system, and a complement of instrumentation to measure salt flow, temperatures, and pressures around the loop. The initial experiment is aimed at measuring fluoride-salt heat transfer inside a heated pebble bed

Acceleration and support post deformation measurements during surface and tunnel transport of a LHC Short Straight Section

CERN Document Server

Capatina, O; CERN. Geneva. TS Department

2004-01-01

This technical note is a complement to the technical note [1]. The former technical note dealt with the experimental modal analysis and the road transport with transport restraints and special suspension. The present note describes the measured accelerations and support post deformations during road transport at reduced speed without end restraints or special suspension. This note also reports the accelerations and support post deformations during handling and tunnel transport with the dedicated tunnel vehicle. The measured accelerations are compared with the specified acceleration limits.

NESSIE: Network Example Source Supporting Innovative Experimentation

Science.gov (United States)

Taylor, Alan; Higham, Desmond J.

We describe a new web-based facility that makes available some realistic examples of complex networks. NESSIE (Network Example Source Supporting Innovative Experimentation) currently contains 12 specific networks from a diverse range of application areas, with a Scottish emphasis. This collection of data sets is designed to be useful for researchers in network science who wish to evaluate new algorithms, concepts and models. The data sets are available to download in two formats (MATLAB's .mat format and .txt files readable by packages such as Pajek), and some basic MATLAB tools for computing summary statistics are also provided.

EXPERIMENTAL MEASUREMENT OF NANOFLUIDS THERMAL PROPERTIES

Directory of Open Access Journals (Sweden)

Adnan M. Hussein

2013-07-01

Full Text Available Solid particles dispersed in a liquid with sizes no larger than 100nm, known as nanofluids, are used to enhance Thermophysical properties compared to the base fluid. Preparations of alumina (Al2O3, titania (TiO2 and silica (SiO2 in water have been experimentally conducted in volume concentrations ranging between 1 and 2.5%. Thermal conductivity is measured by the hot wire method and viscosity with viscometer equipment. The results of thermal conductivity and viscosity showed an enhancement (0.5–20% and 0.5–60% respectively compared with the base fluid. The data measured agreed with experimental data of other researchers with deviation of less than 5%. The study showed that alumina has the highest thermal conductivity, followed silica and titania, on the other hand silica has the highest viscosity followed alumina and titania.

Effect of chest compressions only during experimental basic life support on alveolar collapse and recruitment.

Science.gov (United States)

Markstaller, Klaus; Rudolph, Annette; Karmrodt, Jens; Gervais, Hendrik W; Goetz, Rolf; Becher, Anja; David, Matthias; Kempski, Oliver S; Kauczor, Hans-Ulrich; Dick, Wolfgang F; Eberle, Balthasar

2008-10-01

The importance of ventilatory support during cardiac arrest and basic life support is controversial. This experimental study used dynamic computed tomography (CT) to assess the effects of chest compressions only during cardiopulmonary resuscitation (CCO-CPR) on alveolar recruitment and haemodynamic parameters in porcine model of ventricular fibrillation. Twelve anaesthetized pigs (26+/-1 kg) were randomly assigned to one of the following groups: (1) intermittent positive pressure ventilation (IPPV) both during basic life support and advanced cardiac life support, or (2) CCO during basic life support and IPPV during advanced cardiac life support. Measurements were acquired at baseline prior to cardiac arrest, during basic life support, during advanced life support, and after return of spontaneous circulation (ROSC), as follows: dynamic CT series, arterial and central venous pressures, blood gases, and regional organ blood flow. The ventilated and atelectatic lung area was quantified from dynamic CT images. Differences between groups were analyzed using the Kruskal-Wallis test, and a pbasic life support in the CCO-CPR group remained clinically relevant throughout the subsequent advanced cardiac life support period and following ROSC, and was associated with prolonged impaired haemodynamics. No inter-group differences in myocardial and cerebral blood flow were observed. A lack of ventilation during basic life support is associated with excessive atelectasis, arterial hypoxaemia and compromised CPR haemodynamics. Moreover, these detrimental effects remain evident even after restoration of IPPV.

Requirements for facilities and measurement techniques to support CFD development for hypersonic aircraft

Science.gov (United States)

Sellers, William L., III; Dwoyer, Douglas L.

1992-01-01

The design of a hypersonic aircraft poses unique challenges to the engineering community. Problems with duplicating flight conditions in ground based facilities have made performance predictions risky. Computational fluid dynamics (CFD) has been proposed as an additional means of providing design data. At the present time, CFD codes are being validated based on sparse experimental data and then used to predict performance at flight conditions with generally unknown levels of uncertainty. This paper will discuss the facility and measurement techniques that are required to support CFD development for the design of hypersonic aircraft. Illustrations are given of recent success in combining experimental and direct numerical simulation in CFD model development and validation for hypersonic perfect gas flows.

Quasi-experimental study designs series-paper 11: supporting the production and use of health systems research syntheses that draw on quasi-experimental study designs.

Science.gov (United States)

Lavis, John N; Bärnighausen, Till; El-Jardali, Fadi

2017-09-01

To describe the infrastructure available to support the production of policy-relevant health systems research syntheses, particularly those incorporating quasi-experimental evidence, and the tools available to support the use of these syntheses. Literature review. The general challenges associated with the available infrastructure include their sporadic nature or limited coverage of issues and countries, whereas the specific ones related to policy-relevant syntheses of quasi-experimental evidence include the lack of mechanism to register synthesis titles and scoping review protocols, the limited number of groups preparing user-friendly summaries, and the difficulty of finding quasi-experimental studies for inclusion in rapid syntheses and research syntheses more generally. Although some new tools have emerged in recent years, such as guidance workbooks and citizen briefs and panels, challenges related to using available tools to support the use of policy-relevant syntheses of quasi-experimental evidence arise from such studies potentially being harder for policymakers and stakeholders to commission and understand. Policymakers, stakeholders, and researchers need to expand the coverage and institutionalize the use of the available infrastructure and tools to support the use of health system research syntheses containing quasi-experimental evidence. Copyright © 2017 Elsevier Inc. All rights reserved.

The Online Social Support Scale: Measure development and validation.

Science.gov (United States)

Nick, Elizabeth A; Cole, David A; Cho, Sun-Joo; Smith, Darcy K; Carter, T Grace; Zelkowitz, Rachel L

2018-05-21

A new measure, the Online Social Support Scale, was developed based on previous theory, research, and measurement of in-person social support. It includes four subscales: Esteem/Emotional Support, Social Companionship, Informational Support, and Instrumental Support. In college and community samples, factor analytic and item response theory results suggest that subtypes of in-person social support also pertain in the online world. Evidence of reliability, convergent validity, and discriminant validity provide excellent psychometric support for the measure. Construct validity accrues to the measure vis-à-vis support for three hypotheses: (a) Various broad types of Internet platforms for social interactions are differentially associated with online social support and online victimization; (b) similar to in-person social support, online social support offsets the adverse effect of negative life events on self-esteem and depression-related outcome; and (c) online social support counteracts the effects of online victimization in much the same way that in-person friends in one social niche counterbalance rejection in other social niches. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Monte Carlo simulation - a powerful tool to support experimental activities in structure reliability

International Nuclear Information System (INIS)

Yuritzinn, T.; Chapuliot, S.; Eid, M.; Masson, R.; Dahl, A.; Moinereau, D.

2003-01-01

Monte-Carlo Simulation (MCS) can have different uses in supporting structure reliability investigations and assessments. In this paper we focus our interest on the use of MCS as a numerical tool to support the fitting of the experimental data related to toughness experiments. (authors)

Benchmarking of Governmental Support Measures for University-Industry Cooperation

Directory of Open Access Journals (Sweden)

Kärt Rõigas

2013-01-01

Full Text Available This paper aims to benchmark Estonian governmental support measures targeted toward enhancing university-industry collaboration to European best practice and make suggestions for the development of these measures. The intensity and scope of university-industry cooperation support measures varies heavily in Europe. The survey of European University-Business Cooperation, Pro Inno Europe and Erawatch database of policy measures, and Community Innovation Survey reveal that Finnish, German and Austrian support systems are best balanced and provide good university-industry cooperation intensity. The cooperation measures in Estonia are weak and improvement should be made by increasing the Estonian governmental funding, mandatory cooperation in support measures, networking and applied research in universities, on-going application possibilities, reducing the bureaucracy, and improving the timing of measures.

An Experimental and Analytical Evaluation of Wall And Window Retrofit Configurations: Supporting the Residential Retrofit Best Practices Guide

Energy Technology Data Exchange (ETDEWEB)

Stovall, Therese K [ORNL; Petrie, Thomas [ORNL; Kosny, Jan [ORNL; Childs, Phillip W [ORNL; Atchley, Jerald Allen [ORNL; Hulvey, Kimberly D [ORNL

2007-11-01

A Retrofit Best Practices Guide was developed to encourage homeowners to consider energy conservation issues whenever they modify their siding or windows. In support of this guide, an experimental program was implemented to measure the performance of a number of possible wall siding and window retrofit configurations. Both thermal and air-leakage measurements were made for a 2.4 x 2.4 m (8 x 8 ft) wall section with and without a 0.9 x 1.2 m (3 x 4 ft) window. The windows tested were previously well-characterized at a dedicated window test facility. A computer model was also used to provide information for the Best Practices Guide. The experimental data for walls and windows were used in conjunction with this model to estimate the total annual energy savings for several typical houses in a number of different locations.

Invited review: Experimental design, data reporting, and sharing in support of animal systems modeling research.

Science.gov (United States)

McNamara, J P; Hanigan, M D; White, R R

2016-12-01

The National Animal Nutrition Program "National Research Support Project 9" supports efforts in livestock nutrition, including the National Research Council's committees on the nutrient requirements of animals. Our objective was to review the status of experimentation and data reporting in animal nutrition literature and to provide suggestions for the advancement of animal nutrition research and the ongoing improvement of field-applied nutrient requirement models. Improved data reporting consistency and completeness represent a substantial opportunity to improve nutrition-related mathematical models. We reviewed a body of nutrition research; recorded common phrases used to describe diets, animals, housing, and environmental conditions; and proposed equivalent numerical data that could be reported. With the increasing availability of online supplementary material sections in journals, we developed a comprehensive checklist of data that should be included in publications. To continue to improve our research effectiveness, studies utilizing multiple research methodologies to address complex systems and measure multiple variables will be necessary. From the current body of animal nutrition literature, we identified a series of opportunities to integrate research focuses (nutrition, reproduction and genetics) to advance the development of nutrient requirement models. From our survey of current experimentation and data reporting in animal nutrition, we identified 4 key opportunities to advance animal nutrition knowledge: (1) coordinated experiments should be designed to employ multiple research methodologies; (2) systems-oriented research approaches should be encouraged and supported; (3) publication guidelines should be updated to encourage and support sharing of more complete data sets; and (4) new experiments should be more rapidly integrated into our knowledge bases, research programs and practical applications. Copyright © 2016 American Dairy Science Association

Oscillation experiments on Cesar and Marius - Experimental devices and measurement techniques

International Nuclear Information System (INIS)

Brunet, Max; Guerange, Jacques; Morier, Francis; Tonolli, Jacky

1969-02-01

An original method of measurement of effective cross sections of fissile materials has been developed by the CEA: a central fuel element of a critical experimental reactor is replaced by a sample containing the material to be studied. The replacement technique is based on oscillating the fuel load of the central channel. Signals are measured which are proportional to reactivity variation and to neutron density disturbance at the vicinity of the central channel, these variation and disturbance being produced by the sample oscillation. Measurements have been performed on experimental reactors (Minerve in Fontenay-aux-Roses, and Cesar and Marius in Cadarache). The authors herein describe the experimental devices and measurement techniques implemented in Marius and Cesar. In a first part, they describe the experimental devices which have been used during the three measurement campaigns (between 1965 and 1967). They report the study of measurement accuracies, and of some problems related to the use of the local detector [fr

A novel full-field experimental method to measure the local compressibility of gas diffusion media

Energy Technology Data Exchange (ETDEWEB)

Lai, Yeh-Hung; Li, Yongqiang [Electrochemical Energy Research Lab, GM R and D, Honeoye Falls, NY 14472 (United States); Rock, Jeffrey A. [GM Powertrain, Honeoye Falls, NY 14472 (United States)

2010-05-15

The gas diffusion medium (GDM) in a proton exchange membrane (PEM) fuel cell needs to simultaneously satisfy the requirements of transporting reactant gases, removing product water, conducting electrons and heat, and providing mechanical support to the membrane electrode assembly (MEA). Concerning the localized over-compression which may force carbon fibers and other conductive debris into the membrane to cause fuel cell failure by electronically shorting through the membrane, we have developed a novel full-field experimental method to measure the local thickness and compressibility of GDM. Applying a uniform air pressure upon a thin polyimide film bonded on the top surface of the GDM with support from the bottom by a flat metal substrate and measuring the thickness change using the 3-D digital image correlation technique with an out-of-plane displacement resolution less than 0.5 {mu}m, we have determined the local thickness and compressive stress/strain behavior in the GDM. Using the local thickness and compressibility data over an area of 11.2 mm x 11.2 mm, we numerically construct the nominal compressive response of a commercial Toray trademark TGP-H-060 based GDM subjected to compression by flat platens. Good agreement in the nominal stress/strain curves from the numerical construction and direct experimental flat-platen measurement confirms the validity of the methodology proposed in this article. The result shows that a nominal pressure of 1.4 MPa compressed between two flat platens can introduce localized compressive stress concentration of more than 3 MPa in up to 1% of the total area at various locations from several hundred micrometers to 1 mm in diameter. We believe that this full-field experimental method can be useful in GDM material and process development to reduce the local hard spots and help to mitigate the membrane shorting failure in PEM fuel cells. (author)

A novel full-field experimental method to measure the local compressibility of gas diffusion media

Science.gov (United States)

Lai, Yeh-Hung; Li, Yongqiang; Rock, Jeffrey A.

The gas diffusion medium (GDM) in a proton exchange membrane (PEM) fuel cell needs to simultaneously satisfy the requirements of transporting reactant gases, removing product water, conducting electrons and heat, and providing mechanical support to the membrane electrode assembly (MEA). Concerning the localized over-compression which may force carbon fibers and other conductive debris into the membrane to cause fuel cell failure by electronically shorting through the membrane, we have developed a novel full-field experimental method to measure the local thickness and compressibility of GDM. Applying a uniform air pressure upon a thin polyimide film bonded on the top surface of the GDM with support from the bottom by a flat metal substrate and measuring the thickness change using the 3-D digital image correlation technique with an out-of-plane displacement resolution less than 0.5 μm, we have determined the local thickness and compressive stress/strain behavior in the GDM. Using the local thickness and compressibility data over an area of 11.2 mm × 11.2 mm, we numerically construct the nominal compressive response of a commercial Toray™ TGP-H-060 based GDM subjected to compression by flat platens. Good agreement in the nominal stress/strain curves from the numerical construction and direct experimental flat-platen measurement confirms the validity of the methodology proposed in this article. The result shows that a nominal pressure of 1.4 MPa compressed between two flat platens can introduce localized compressive stress concentration of more than 3 MPa in up to 1% of the total area at various locations from several hundred micrometers to 1 mm in diameter. We believe that this full-field experimental method can be useful in GDM material and process development to reduce the local hard spots and help to mitigate the membrane shorting failure in PEM fuel cells.

Evaluation of support group interventions for children in troubled families: study protocol for a quasi-experimental control group study.

Science.gov (United States)

Skerfving, Annemi; Johansson, Fredrik; Elgán, Tobias H

2014-01-24

Support groups for children in troubled families are available in a majority of Swedish municipalities. They are used as a preventive effort for children in families with different parental problems such as addiction to alcohol/other drugs, mental illness, domestic violence, divorce situations, or even imprisonment. Children from families with these problems are a well-known at-risk group for various mental health and social problems. Support groups aim at strengthening children's coping behaviour, to improve their mental health and to prevent a negative psycho-social development. To date, evaluations using a control-group study design are scarce. The aim of the current study is to evaluate the effects of support groups. This paper describes the design of an effectiveness study, initially intended as a randomized controlled trial, but instead is pursued as a quasi-experimental study using a non-randomized control group. The aim is to include 116 children, aged 7-13 years and one parent/another closely related adult, in the study. Participants are recruited via existing support groups in the Stockholm county district and are allocated either into an intervention group or a waiting list control group, representing care as usual. The assessment consists of questionnaires that are to be filled in at baseline and at four months following the baseline. Additionally, the intervention group completes a 12-month follow-up. The outcomes include the Strength and Difficulties Questionnaire (SDQ S11-16), the Kids Coping Scale, the "Ladder of life" which measures overall life satisfaction, and "Jag tycker jag är" (I think I am) which measures self-perception and self-esteem. The parents complete the SDQ P4-16 (parent-report version) and the Swedish scale "Familjeklimat" (Family Climate), which measures the emotional climate in the family. There is a need for evaluating the effects of support groups targeted to children from troubled families. This quasi-experimental study

11. International conference on WWER fuel performance, modelling and experimental support. Proceedings

International Nuclear Information System (INIS)

Manolova, M.; Boneva, S.; Mitev, M.

2015-01-01

This publication is a compilation of the papers presented in 11th International Conference on WWER Fuel Performance, Modeling and Experimental Support, organized by the Institute for Nuclear Research and Nuclear Energy (INRNE) of the Bulgarian Academy of Sciences in co-operation with the International Atomic Energy Agency (IAEA), Vienna, Austria, supported by the Kozloduy Nuclear Power Plant (KNPP), the Bulgarian Nuclear Regulatory Agency, and TVEL Fuel Company, Russia. The Conference took place in hotel Bolero, Golden Sands Resort, Bulgaria, from 26 September 2015 to 3 October 2015. It was attended by 117 participants, among them more than 100 experts and specialists from 22 countries, including representatives of 3 international organizations, 16 Russian organizations and other 36 foreign institutes, nuclear fuel plants, nuclear power plants and organizations responsible for WWER and PWR fuel design, manufacturing and research, and 3 Bulgarian organizations, working for the Bulgarian nuclear industry. 70 papers have been presented in the Conference in 6 oral and 1 poster session, covering: (1) general overview lectures; (2) fuel performance and operational experience; (3) fuel modeling and experimental support; (4) fuel safety and QA; (5) spent fuel performance and management; (6) specific issues of WWER-1000 fuel reliability. The proceedings provide Summary, Conclusions and Recommendations of the Conference, together with the full text of the presentations. IAEA Technical Meeting (TM) “Achieving zero fuel failure rates: challenges and perspectives”, 1 – 2 October 2015 was organized in conjunction with the 11th International Conference on WWER Fuel Performance, Modelling and Experimental Support. The reports presented on TM sessions are included in the Conference Proceedings too

Numerical Simulations and Experimental Measurements of Scale-Model Horizontal Axis Hydrokinetic Turbines (HAHT) Arrays

Science.gov (United States)

Javaherchi, Teymour; Stelzenmuller, Nick; Seydel, Joseph; Aliseda, Alberto

2014-11-01

The performance, turbulent wake evolution and interaction of multiple Horizontal Axis Hydrokinetic Turbines (HAHT) is analyzed in a 45:1 scale model setup. We combine experimental measurements with different RANS-based computational simulations that model the turbines with sliding-mesh, rotating reference frame and blame element theory strategies. The influence of array spacing and Tip Speed Ratio on performance and wake velocity structure is investigated in three different array configurations: Two coaxial turbines at different downstream spacing (5d to 14d), Three coaxial turbines with 5d and 7d downstream spacing, and Three turbines with lateral offset (0.5d) and downstream spacing (5d & 7d). Comparison with experimental measurements provides insights into the dynamics of HAHT arrays, and by extension to closely packed HAWT arrays. The experimental validation process also highlights the influence of the closure model used (k- ω SST and k- ɛ) and the flow Reynolds number (Re=40,000 to 100,000) on the computational predictions of devices' performance and characteristics of the flow field inside the above-mentioned arrays, establishing the strengths and limitations of existing numerical models for use in industrially-relevant settings (computational cost and time). Supported by DOE through the National Northwest Marine Renewable Energy Center (NNMREC).

Experimental investigation of the characteristics of a laser beam passing through a fluid layer for surface quality in-process measurement

International Nuclear Information System (INIS)

Guo, Ruipeng; Tao, Zhengsu

2010-01-01

The optical characteristics of a laser beam passing through a fluid parallel layer are examined through a series of experimental tests in this project. The experimental apparatus consists of a bare surface quality measurement system and a fluid-supporting system. In the case of laser beam propagation through the static fluid layer, a modified Beckmann–Kirchhoff scattering model has been developed. Based on this model, the results of the surface quality in-process optical measurement can be amended. By extracting a ratio parameter from the image of the scattered light pattern to estimate surface roughness, the modified model can be verified quantitatively in the experimental system. As far as laser beam propagation through the flowing fluid layer is concerned, the deflection of the laser beam caused by fluid flow is small. The experiments are conducted to investigate the characteristics, and the results show that the resulting measurement error for surface quality optical measurement is in an acceptable range

Experimental Support for Evaluation of the Victoria Class Virtual Submarine (VCVS)

Science.gov (United States)

2012-03-01

comportementales de ce genre . y A P P R O V A L S H E E T Document No. 5283-001 Version 03 Document Name: Experimental Support for Evaluation...encountered that reduced access to HMCS Corner Brook: 11  Cold moves to charge submarine batteries;  Filming events; and,  Slight delays due

Operational Contract Support: Economic Impact Evaluation and Measures of Effectiveness

Science.gov (United States)

2017-12-01

NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA MBA PROFESSIONAL REPORT OPERATIONAL CONTRACT SUPPORT: ECONOMIC IMPACT EVALUATION AND MEASURES...DATES COVERED MBA professional report 4. TITLE AND SUBTITLE OPERATIONAL CONTRACT SUPPORT: ECONOMIC IMPACT EVALUATION AND MEASURES OF EFFECTIVENESS 5...evaluation, expeditionary economics , operational contract support, measure of effectiveness 15. NUMBER OF PAGES 89 16. PRICE CODE 17. SECURITY

Experimental measurements of negative hydrogen ion production from surfaces

International Nuclear Information System (INIS)

Graham, W.G.

1977-09-01

Experimental measurements of the production of H - from surfaces bombarded with hydrogen are reviewed. Some measurements of H + and H 0 production from surfaces are also discussed with particular emphasis on work which might be relevant to ion source applications

An experimental device for measurement of gas permeation in solid matrices

International Nuclear Information System (INIS)

De Salve, M.; Mazzi, E.; Zucchetti, M.

1996-01-01

The inventory in and the permeation through fusion reactor structures of hydrogen and its isotopes play an important role in the machine operation, evolution of material properties, and safety. An experimental and research activity for the determination of permeability (and derived parameters) of gases in solid matrices is described. It uses a gas permeation method, that basically consists in the measure of the time evolution of the gas pressure in a chamber in which vacuum has been previously made (downstream volume). This chamber is separated from another one, full of the gas in exam (upstream volume), by means of a membrane of the material under study. The experimental installation is described. The first stage of the experimental activity has dealt with the set-up of the device, the volume calibration, and the definition of the parameters range for which the installation can give reliable measurements. The subsequent stage of the activity has consisted in the measurement of the permeability, and then of the diffusion coefficient, of nitrogen in some materials at room temperature. Concurrently with the experimental activity, a model has been set-up and implemented in a computer code: this code permits to evaluate the time evolution of the pressure in the downstream chamber. With this code, using the measured parameters, the time evolution of the pressure experimentally measured has been satisfactorily reproduced. (author)

Measuring strategy of Support Centre RIVM for nuclear emergencies

International Nuclear Information System (INIS)

Pruppers, M.J.M.; Smetsers, R.C.G.M.

1994-11-01

The accident at the Chernobyl nuclear power station in April 1986 and its consequences were reason for the Dutch government to evaluate and improve the facilities and the preparedness for nuclear emergency management in the Netherlands. The results of the evaluation have been elaborated in operational terms in the National Plan for Nuclear Emergency Planning and Response (EPR). During an accident with radioactive material the Technical Information Group (TIG) coordinates the measuring activities of the so-called Support Centres. According to the EPR, measuring activities of Support Centre RIVM are focussed on the collection and processing of data on emissions, concentrations, depositions and radiation doses from soil and air. This report describes the measuring strategy of RIVM for nuclear emergencies. The measuring strategy and the measuring plan, the latter deduced from the measuring strategy, concentrate on explicit answers to the following central questions: what has to be measured, by whom, where, when and how, and why? The demands of the TIG and the specification of tasks and operational facilities of Support Centre RIVM are considered as starting-points, limiting conditions and constraints for the measuring strategy. These items are converted to explicit choices for the measuring strategy and the default measuring plan. This report further includes a list of contacts of Support Centre RIVM with other (research) institutes, inside and outside the Netherlands, which may be relevant during a nuclear emergency. 3 figs., 2 tabs., 22 refs

Experimental technologies comparison for strain measurement of a composite main landing gear bay specimen

Science.gov (United States)

Viscardi, Massimo; Arena, Maurizio; Ciminello, Monica; Guida, Michele; Meola, Carosena; Cerreta, Pietro

2018-03-01

The development of advanced monitoring system for strain measurements on aeronautical components remain an important target both when related to the optimization of the lead-time and cost for part validation, allowing earlier entry into service, and when related to the implementation of advanced health monitoring systems dedicated to the in-service parameters verification and early stage detection of structural problems. The paper deals with the experimental testing of a composite samples set of the main landing gear bay for a CS-25 category aircraft, realized through an innovative design and production process. The test have represented a good opportunity for direct comparison of different strain measurement techniques: Strain Gauges (SG) and Fibers Bragg Grating (FBG) have been used as well as non-contact techniques, specifically the Digital Image Correlation (DIC) and Infrared (IR) thermography applied where possible in order to highlight possible hot-spot during the tests. The crucial points identification on the specimens has been supported by means of advanced finite element simulations, aimed to assessment of the structural strength and deformation as well as to ensure the best performance and the global safety of the whole experimental campaign.

Experimental Evaluation of Tachistoscopic Measurement: A Step Beyond Wundt’s Criticism

Czech Academy of Sciences Publication Activity Database

Vobořil, Dalibor; Jelínek, Martin; Květon, Petr

2014-01-01

Roč. 127, č. 2 (2014), 245–252 ISSN 0002-9556 Institutional support: RVO:68081740 Keywords : history of psychology * tachistoscop * experimental instruments Subject RIV: AN - Psychology Impact factor: 0.619, year: 2014

A novel experimental technique of nuclear lifetime measurements

International Nuclear Information System (INIS)

Yuminov, O.A.; D'Arrigo, A.; Giardina, G.; Taccone, A.; Vannini, G.; Moroni, A.; Ricci, R.A.; Vannucci, L.

1995-01-01

In the present paper a new experimental method to measure nuclear reaction time in the 10 -15 -10 -10 s region is presented. Measurements of the lifetimes of low-lying and long-lived states of 19 F and 20 Ne decaying via α-channel were carried out with the aim of checking the feasibility of the method. The results obtained in this way are compared with the lifetimes known from different techniques. ((orig.))

The experimental watersheds in Slovenia

International Nuclear Information System (INIS)

Sraj, M; Rusjan, S; Petan, S; Vidmar, A; Mikos, M; Globevnik, L; Brilly, M

2008-01-01

Experimental watersheds are critical to the advancement of hydrological science. By setting up three experimental watersheds, Slovenia also obtained its grounds for further development of the science and discipline. In the Dragonja experimental watershed the studies are focused on the afforestation of the watershed in a mediterranean climate, on the Reka river the water balance in a partly karstic area is examined, and on the case of the Glinscica stream the implications of the urban environment are studied. We have obtained valuable experience and tested new measuring equipment on all three experimental watersheds. Measurements and analysis on the experimental watersheds improved the current understanding of hydrological processes. They resulted in several PhD Theses, Master Theses and scientific articles. At the same time the experimental watersheds provide support to the teaching and studying process.

Metacognitive and multimedia support of experiments in inquiry learning for science teacher preparation

Science.gov (United States)

Bruckermann, Till; Aschermann, Ellen; Bresges, André; Schlüter, Kirsten

2017-04-01

Promoting preservice science teachers' experimentation competency is required to provide a basis for meaningful learning through experiments in schools. However, preservice teachers show difficulties when experimenting. Previous research revealed that cognitive scaffolding promotes experimentation competency by structuring the learning process, while metacognitive and multimedia support enhance reflection. However, these support measures have not yet been tested in combination. Therefore, we decided to use cognitive scaffolding to support students' experimental achievements and supplement it by metacognitive and multimedia scaffolds in the experimental groups. Our research question is to what extent supplementing cognitive support by metacognitive and multimedia scaffolding further promotes experimentation competency. The intervention has been applied in a two-factorial design to a two-month experimental course for 63 biology teacher students in their first bachelor year. Pre-post-test measured experimentation competency in a performance assessment. Preservice teachers worked in groups of four. Therefore, measurement took place at group level (N = 16). Independent observers rated preservice teachers' group performance qualitatively on a theory-based system of categories. Afterwards, experimentation competency levels led to quantitative frequency analysis. The results reveal differing gains in experimentation competency but contrary to our hypotheses. Implications of combining scaffolding measures on promoting experimentation competency are discussed.

New experimental procedure for measuring volume magnetostriction on powder samples

International Nuclear Information System (INIS)

Rivero, G.; Multigner, M.; Valdes, J.; Crespo, P.; Martinez, A.; Hernando, A.

2005-01-01

Conventional techniques used for volume magnetostriction measurements, as strain gauge or cantilever method, are very useful for ribbons or thin films but cannot be applied when the samples are in powder form. To overcome this problem a new experimental procedure has been developed. In this work, the experimental set-up is described, together with the results obtained in amorphous FeCuZr powders, which exhibit a strong dependence of the magnetization on the strength of the applied magnetic field. The magnetostriction measurements presented in this work point out that this dependence is related to a magnetovolume effect

Experimental measurements and mathematics; Les mesures experimentales et les mathematiques

Energy Technology Data Exchange (ETDEWEB)

Abraham, I.; Bruno, S.; Durand, O.; Gaillard, P.; Lagrange, J.M.; Lamy, F.; Peyrat, J.P. [CEA Bruyeres-le-Chatel, 91 (France); Choux, A.; Druoton, L.; Pascal, G.; Sulpice, F. [CEA Valduc, 21 - Is-sur-Tille (France); Busvelle, E.; Garnier, L. [Universite de Bourgogne, Lab. d' Electronique, Informatique et Image, 21 - Dijon (France); Gauthier, J.P. [Laboratoire des Sciences de l' Information et des Systemes, 83 - Toulon (France); Langevin, R. [Institut Mathematique de Bourgogne, 21 - Dijon (France)

2011-01-15

Many problems that appear in experimental works can be solved by using mathematical methods, from the conception phase to the interpretation of measurements. We illustrate the use of these methods at CEA-DAM by pointing out some examples in 3 typical domains: treatment of experimental data, geometrical controls of targets, and analysis of a huge quantity of data. (authors)

Analysis of experimental measurements of PWR fresh and spent fuel assemblies using Self-Interrogation Neutron Resonance Densitometry

Energy Technology Data Exchange (ETDEWEB)

LaFleur, Adrienne M., E-mail: alafleur@lanl.gov; Menlove, Howard O., E-mail: hmenlove@lanl.gov

2015-05-01

Self-Interrogation Neutron Resonance Densitometry (SINRD) is a new NDA technique that was developed at Los Alamos National Laboratory (LANL) to improve existing nuclear safeguards measurements for LWR fuel assemblies. The SINRD detector consists of four fission chambers (FCs) wrapped with different absorber filters to isolate different parts of the neutron energy spectrum and one ion chamber (IC) to measure the gross gamma rate. As a result, two different techniques can be utilized using the same SINRD detector unit and hardware. These techniques are the Passive Neutron Multiplication Counter (PNMC) method and the SINRD method. The focus of the work described in this paper is the analysis of experimental measurements of fresh and spent PWR fuel assemblies that were performed at LANL and the Korea Atomic Energy Research Institute (KAERI), respectively, using the SINRD detector. The purpose of these experiments was to assess the following capabilities of the SINRD detector: 1) reproducibility of measurements to quantify systematic errors, 2) sensitivity to water gap between detector and fuel assembly, 3) sensitivity and penetrability to the removal of fuel rods from the assembly, and 4) use of PNMC/SINRD ratios to quantify neutron multiplication and/or fissile content. The results from these simulations and measurements provide valuable experimental data that directly supports safeguards research and development (R&D) efforts on the viability of passive neutron NDA techniques and detector designs for partial defect verification of spent fuel assemblies. - Highlights: • Experimental measurements of PWR fresh and spent FAs were performed with SINRD. • Good agreement of MCNPX and measured results confirmed accuracy of SINRD model. • For fresh fuel, SINRD and PNMC ratios were not sensitive to water gaps of ≤5-mm. • Practical use of SINRD would be in Fork detector to reduce systematic uncertainties.

Experimental results supporting the concept of one-sided muon tomography

Energy Technology Data Exchange (ETDEWEB)

Boniface, K., E-mail: bonifak@mcmaster.ca [McMaster University, Hamilton, ON (Canada); Jonkmans, G. [Canadian Nuclear Laboratories, Chalk River, ON (Canada); Buijs, A. [McMaster University, Hamilton, ON (Canada); Erlandson, A.; Livingstone, S. [Canadian Nuclear Laboratories, Chalk River, ON (Canada)

2015-07-01

Naturally occurring cosmic-ray muons have been shown to exhibit properties ideal for imaging the interior of structures containing material of high density and atomic number. The commonly used method for 3D imaging requires two modules of detection in order to measure muon scattering. This paper provides experimental results for a novel 3D imaging method that uses a reconstruction algorithm common to medical imaging and only one module of detection in order to measure the attenuation of the muon flux at several angles of rotation around a structure. (author)

Experimental measurement of zero power reactor transfer function

International Nuclear Information System (INIS)

Liang Shuhong

2011-01-01

In order to study the zero power reactor (ZPR) transfer function, the ZPR transfer function expression was deduced with the point reactor kinetics equation, which was disturbed by reactivity input response. Based on the Fourier analysis for the input of triangular wave, the relation between the transfer function and reactivity was got. Validating research experiment was made on the DF-VI fast ZPR. After the disturbed reactivity was measured, the experimental value of the transfer function was got. According to the experimental value and the calculated value, the expression of the ZPR transfer function is proved, whereas the disturbed reactivity is got from the transfer function. (authors)

Bayesian optimal experimental design for priors of compact support

KAUST Repository

Long, Quan

2016-01-08

In this study, we optimize the experimental setup computationally by optimal experimental design (OED) in a Bayesian framework. We approximate the posterior probability density functions (pdf) using truncated Gaussian distributions in order to account for the bounded domain of the uniform prior pdf of the parameters. The underlying Gaussian distribution is obtained in the spirit of the Laplace method, more precisely, the mode is chosen as the maximum a posteriori (MAP) estimate, and the covariance is chosen as the negative inverse of the Hessian of the misfit function at the MAP estimate. The model related entities are obtained from a polynomial surrogate. The optimality, quantified by the information gain measures, can be estimated efficiently by a rejection sampling algorithm against the underlying Gaussian probability distribution, rather than against the true posterior. This approach offers a significant error reduction when the magnitude of the invariants of the posterior covariance are comparable to the size of the bounded domain of the prior. We demonstrate the accuracy and superior computational efficiency of our method for shock-tube experiments aiming to measure the model parameters of a key reaction which is part of the complex kinetic network describing the hydrocarbon oxidation. In the experiments, the initial temperature and fuel concentration are optimized with respect to the expected information gain in the estimation of the parameters of the target reaction rate. We show that the expected information gain surface can change its shape dramatically according to the level of noise introduced into the synthetic data. The information that can be extracted from the data saturates as a logarithmic function of the number of experiments, and few experiments are needed when they are conducted at the optimal experimental design conditions.

Calculation and experimental measurements in the Argonauta reactor subcritical and exponential facility

International Nuclear Information System (INIS)

Voi, Dante L.; Furieri, Rosane C.A.A.; Renke, Carlos A.C.; Bastos, Wilma S.; Ferreira, Francisco J.O.

1997-01-01

Initial measurements were performed on the exponential and subcritical facility installed on the internal thermal column of the Argonauta reactor at IEN-CNEN-Rio de Janeiro, Brazil. The measurements are include in the reactor physics experimental program for integral parameters determination, for both valid and confirmed theoretical models for reactor calculation. Gamma doses and neutron fluxes were measured with telescopic, proportional counters, wire and foil detectors. Experimental data were compared with results obtained by application of CITATION code. (author). 4 refs., 8 figs

Experimental measurement of flexion-extension movement in normal and corpse prosthetic elbow joint.

Science.gov (United States)

TarniŢă, Daniela; TarniŢă, DănuŢ Nicolae

2016-01-01

This paper presents a comparative experimental study of flexion-extension movement in healthy elbow and in the prosthetic elbow joint fixed on an original experimental bench. Measurements were carried out in order to validate the functional morphology and a new elbow prosthesis type ball head. The three-dimensional (3D) model and the physical prototype of our experimental bench used to test elbow endoprosthesis at flexion-extension and pronation-supination movements is presented. The measurements were carried out on a group of nine healthy subjects and on the prosthetic corpse elbow, the experimental data being obtained for flexion-extension movement cycles. Experimental data for the two different flexion-extension tests for the nine subjects and for the corpse prosthetic elbow were acquired using SimiMotion video system. Experimental data were processed statistically. The corresponding graphs were obtained for all subjects in the experimental group, and for corpse prosthetic elbow for both flexion-extension tests. The statistical analysis has proved that the flexion angles of healthy elbows were significantly close to the values measured at the prosthetic elbow fixed on the experimental bench. The studied elbow prosthesis manages to re-establish the mobility for the elbow joint as close to the normal one.

Overhead traveling crane vibration research using experimental wireless measuring system

Directory of Open Access Journals (Sweden)

Tomasz HANISZEWSKI

2013-01-01

Full Text Available The paper contains an operations and constructions description of theexperimental wireless measuring system for measuring accelerations in bridge cranes,based on PHIDGET 1056 sensors. Developed experimental research and measuringmethodology allows the use of the proposed wireless system on other cranesconstructions. The paper also shows examples of the results of vibration measurementsand FFT spectra, obtained on the basis of accelerations measurements.

Measurement of dynamic interaction between a vibrating fuel element and its support

Energy Technology Data Exchange (ETDEWEB)

Fisher, N.J.; Tromp, J.H.; Smith, B.A.W. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada). Chalk River Labs.

1996-12-01

Flow-induced vibration of CANDU{reg_sign} fuel can result in fretting damage of the fuel and its support. A WOrk-Rate Measuring Station (WORMS) was developed to measure the relative motion and contact forces between a vibrating fuel element and its support. The fixture consists of a small piece of support structure mounted on a micrometer stage. This arrangement permits position of the support relative to the fuel element to be controlled to within {+-} {micro}m. A piezoelectric triaxial load washer is positioned between the support and micrometer stage to measure contact forces, and a pair of miniature eddy-current displacement probes are mounted on the stage to measure fuel element-to-support relative motion. WORMS has been utilized to measure dynamic contact forces, relative displacements and work-rates between a vibrating fuel element and its support. For these tests, the fuel element was excited with broadband random force excitation to simulate flow-induced vibration due to axial flow. The relationship between fuel element-to-support gap or preload (i.e., interference or negative gap) and dynamic interaction (i.e., relative motion, contact forces and work-rates) was derived. These measurements confirmed numerical simulations of in-reactor interaction predicted earlier using the VIBIC code.

A new experimental setup for high-pressure catalytic activity measurements on surface deposited mass-selected Pt clusters

International Nuclear Information System (INIS)

Watanabe, Yoshihide; Isomura, Noritake

2009-01-01

A new experimental setup to study catalytic and electronic properties of size-selected clusters on metal oxide substrates from the viewpoint of cluster-support interaction and to formulate a method for the development of heterogeneous catalysts such as automotive exhaust catalysts has been developed. The apparatus consists of a size-selected cluster source, a photoemission spectrometer, a scanning tunneling microscope (STM), and a high-pressure reaction cell. The high-pressure reaction cell measurements provided information on catalytic properties in conditions close to practical use. The authors investigated size-selected platinum clusters deposited on a TiO 2 (110) surface using a reaction cell and STM. Catalytic activity measurements showed that the catalytic activities have a cluster-size dependency.

Experimental measurement of energy harvesting with backpack

Science.gov (United States)

Pavelkova, Radka; Vala, David; Suranek, Pavel; Mahdal, Miroslav

2017-08-01

This article deals with the energy harvesting systems, especially the energy harvesting backpack, which appears as a convenient means for energy harvesting for mobile sensors power. Before starting the experiment, it was necessary to verify whether this energy will be sufficient to get acquainted with the human kinematics and analyze problematics itself. For this purpose there was used motion capture technology from Xsens. Measured data on the position of a particle moving man and back when walking, these data were then used for experimental realization of energy harvesting backpack and as input data to the simulation in Simulink, which brought us a comparison between theoretical assumptions and practical implementation. When measuring characteristics of energy harvesting system we have a problem with measurements on backpack solved when redoing of the hydraulic cylinder as a source of a suitable movement corresponding to the amplitude and frequency of human walk.

miRSponge: a manually curated database for experimentally supported miRNA sponges and ceRNAs.

Science.gov (United States)

Wang, Peng; Zhi, Hui; Zhang, Yunpeng; Liu, Yue; Zhang, Jizhou; Gao, Yue; Guo, Maoni; Ning, Shangwei; Li, Xia

2015-01-01

In this study, we describe miRSponge, a manually curated database, which aims at providing an experimentally supported resource for microRNA (miRNA) sponges. Recent evidence suggests that miRNAs are themselves regulated by competing endogenous RNAs (ceRNAs) or 'miRNA sponges' that contain miRNA binding sites. These competitive molecules can sequester miRNAs to prevent them interacting with their natural targets to play critical roles in various biological and pathological processes. It has become increasingly important to develop a high quality database to record and store ceRNA data to support future studies. To this end, we have established the experimentally supported miRSponge database that contains data on 599 miRNA-sponge interactions and 463 ceRNA relationships from 11 species following manual curating from nearly 1200 published articles. Database classes include endogenously generated molecules including coding genes, pseudogenes, long non-coding RNAs and circular RNAs, along with exogenously introduced molecules including viral RNAs and artificial engineered sponges. Approximately 70% of the interactions were identified experimentally in disease states. miRSponge provides a user-friendly interface for convenient browsing, retrieval and downloading of dataset. A submission page is also included to allow researchers to submit newly validated miRNA sponge data. Database URL: http://www.bio-bigdata.net/miRSponge. © The Author(s) 2015. Published by Oxford University Press.

Experimental determination of entanglement with a single measurement.

Science.gov (United States)

Walborn, S P; Souto Ribeiro, P H; Davidovich, L; Mintert, F; Buchleitner, A

2006-04-20

Nearly all protocols requiring shared quantum information--such as quantum teleportation or key distribution--rely on entanglement between distant parties. However, entanglement is difficult to characterize experimentally. All existing techniques for doing so, including entanglement witnesses or Bell inequalities, disclose the entanglement of some quantum states but fail for other states; therefore, they cannot provide satisfactory results in general. Such methods are fundamentally different from entanglement measures that, by definition, quantify the amount of entanglement in any state. However, these measures suffer from the severe disadvantage that they typically are not directly accessible in laboratory experiments. Here we report a linear optics experiment in which we directly observe a pure-state entanglement measure, namely concurrence. Our measurement set-up includes two copies of a quantum state: these 'twin' states are prepared in the polarization and momentum degrees of freedom of two photons, and concurrence is measured with a single, local measurement on just one of the photons.

Experimental study of flow patterns near tube support structures

International Nuclear Information System (INIS)

Rummens, H.E.C.; Turner, C.W.

1994-07-01

Extensive blockage of broached support plates in steam generators has occurred at the Bruce A Nuclear Generating Station (NGS), forcing unit derating in 1988 March. Blockage has also been found on the lower broached plates of the Pickering B and Point Lepreau NGSs. Water chemistry and operating conditions are known to influence fouling directly. We suspect that flow patterns also play a role, that these patterns are influenced by the geometry of steam generator (SG) components, and that particularly the broached plate design actively creates an environment favorable to deposition. Experiments are in progress to examine the flow patterns near various tube supports: the broached plate, two types of lattice bars, and the formed bars. Preliminary tests in an air/water loop with 1/2- and 7-tube SG mockups containing the tube supports have been completed. Flow patterns were visualized using injected air bubbles. Local velocities and turbulence levels were measured using a laser technique, which confirmed observations of flow recirculation and stagnation. Axial pressure profiles were measured to determine overall resistance coefficients, and to identify local pressure extremes. Some visualization tests were also carried out on an artificially fouled broached plate. Based on results to date, several deposition mechanisms are proposed: deposition of particles in stagnant regions, deposition of solubles due to flashing in low-pressure regions, and deposition in smaller channels due to steam migration toward larger channels. A qualitative assessment of the tube support designs based on these mechanisms implies that the relative resistances to fouling are: (WORST) broach plate << lattice bars << formed bars (BEST). As the air/water simulation shows only hydraulic flow patterns, further tests will be done in a simple liquid/vapor Freon loop to examine thermal effects. (author). 3 refs., 10 figs

Contact Angle Measurements Using a Simplified Experimental Setup

Science.gov (United States)

Lamour, Guillaume; Hamraoui, Ahmed; Buvailo, Andrii; Xing, Yangjun; Keuleyan, Sean; Prakash, Vivek; Eftekhari-Bafrooei, Ali; Borguet, Eric

2010-01-01

A basic and affordable experimental apparatus is described that measures the static contact angle of a liquid drop in contact with a solid. The image of the drop is made with a simple digital camera by taking a picture that is magnified by an optical lens. The profile of the drop is then processed with ImageJ free software. The ImageJ contact…

Experimental Measurements of Temporal Dispersion for Underwater Laser Communications and Imaging

Science.gov (United States)

Cochenour, Brandon Michael

The challenge in implementing optical sensors underwater lies in the high variability of the ocean environment where propagation of light in the ocean is complicated by absorption and scattering. Most underwater optical sensors operate in the blue/green portion of the electromagnetic spectrum where seawater exhibits an absorption minimum. Mitigating scattering however is a greater challenge. In particular, scattering causes both spatial distortion (beam spreading) and temporal dispersion (pulse spreading or distortion). Each of type of dispersion decreases sensor performance (operating range, image resolution, data bandwidth, etc.). While spatial dispersion has received a great deal of attention in previous decades, technological limitations of sensor hardware have made experimental measurements of temporal dispersion underwater difficult until now. The main contribution of this thesis are experimental measurements of temporal dispersion of optical beams in turbid water, made with a high sensitivity/high dynamic range experimental technique. Measurements are performed as a function of water clarity (0-20 attenuation lengths), transmitter/receiver alignment (0-30 degrees, half angle), receiver field of view (1-7 degrees, full angle), and transmitter beam divergence (collimated and diffuse). Special attention is paid to the interdependency between spatial and temporal dispersion. This work provides severable notable contributions: 1. While experimental characterization of spatial dispersion has received significant attention underwater, there has been a lack of measurements characterizing temporal dispersion underwater. This work provides the most comprehensive set of experimental measurements to date regarding the temporal dispersion of optical beams underwater. 2. An experimental analysis of the influence of scattering phase function on temporal dispersion. Coarse estimates of the scattering phase function are used to determine the ranges (or attenuation lengths

Impact of measurement uncertainty from experimental load distribution factors on bridge load rating

Science.gov (United States)

Gangone, Michael V.; Whelan, Matthew J.

2018-03-01

Load rating and testing of highway bridges is important in determining the capacity of the structure. Experimental load rating utilizes strain transducers placed at critical locations of the superstructure to measure normal strains. These strains are then used in computing diagnostic performance measures (neutral axis of bending, load distribution factor) and ultimately a load rating. However, it has been shown that experimentally obtained strain measurements contain uncertainties associated with the accuracy and precision of the sensor and sensing system. These uncertainties propagate through to the diagnostic indicators that in turn transmit into the load rating calculation. This paper will analyze the effect that measurement uncertainties have on the experimental load rating results of a 3 span multi-girder/stringer steel and concrete bridge. The focus of this paper will be limited to the uncertainty associated with the experimental distribution factor estimate. For the testing discussed, strain readings were gathered at the midspan of each span of both exterior girders and the center girder. Test vehicles of known weight were positioned at specified locations on each span to generate maximum strain response for each of the five girders. The strain uncertainties were used in conjunction with a propagation formula developed by the authors to determine the standard uncertainty in the distribution factor estimates. This distribution factor uncertainty is then introduced into the load rating computation to determine the possible range of the load rating. The results show the importance of understanding measurement uncertainty in experimental load testing.

Care and supportive measures in school-aged children with prenatal substance exposure.

Science.gov (United States)

Sandtorv, Lisbeth B; Haugland, Siren; Elgen, Irene

2017-12-01

Prenatal exposure to substances, including alcohol, opiates, and a number of illicit drugs, may have a negative impact on fetal development. Studies have shown that substance exposure can influence a child's neurodevelopment and the need for care and supportive measures. In this study, we aimed to investigate the care status and the level of supportive measures in school-aged children prenatally exposed to alcohol and other substances. This study included children aged between 6 and 14 years who were referred to Haukeland University Hospital in Norway with developmental impairment and a history of prenatal substance exposure. Participants were classified according to their main prenatal exposure to either alcohol or other substances. Information on care status and supportive measures was obtained from medical records and participants' caregivers. We also compared the use of supportive measures for children placed into foster care before and after 1 year of age. A total of 111 (87% of 128 referrals) eligible children participated in the study. Of these 111 children, 96 (86%) were in foster care, of whom 29 (30%) were placed into foster care during their first year of life and 83 out of 90 (92%) had supportive measures, including reinforced foster care and school or social support. A high proportion of the sample lived in foster care and received supportive measures. Findings may reflect an increased need of care and support in school-aged children with prenatal substance exposure, highlighting the importance of awareness among caregivers and public agencies.

Experimental study of the drying in dense fluidized beds of a synthetic mud coated with support particulates; Etude experimentale du sechage en lit fluidise dense d'une boue synthetique enrobee sur des particules supports

Energy Technology Data Exchange (ETDEWEB)

Gode, C.; Shakourzadeh, K. [Universite de Technologie de Compiegne, L.G.P.I., 60 (France)

2001-07-01

This article presents the results of an experimental study of a new drying process for muddy materials and based on the fluidization technique. The granular phase has been obtained by the coating with mud of a porous mineral support, inert and recyclable in the process. Activated porous particulates of alumina (2-5 mm) have been chosen because of their heat transfer properties. A first part of the experimental study concerns the drying process. The second part concerns the attrition and elutriation mechanisms. The experimental measurements have been performed with a laboratory fluidized column (internal diameter = 150 mm) and with a fluidized column (internal diameter = 400 mm) from a semi-industrial facility. The air velocity and the drying temperature are the main adjustment parameters. The working temperatures have been fixed between 20 and 150 deg. C. (J.S.)

Psychometrics of a Child Report Measure of Maternal Support following Disclosure of Sexual Abuse.

Science.gov (United States)

Smith, Daniel W; Sawyer, Genelle K; Heck, Nicholas C; Zajac, Kristyn; Solomon, David; Self-Brown, Shannon; Danielson, Carla K; Ralston, M Elizabeth

2017-04-01

The study examined a new child report measure of maternal support following child sexual abuse. One hundred and forty-six mother-child dyads presenting for a forensic evaluation completed assessments including standardized measures of adjustment. Child participants also responded to 32 items considered for inclusion in a new measure, the Maternal Support Questionnaire-Child Report (MSQ-CR). Exploratory factor analysis of the Maternal Support Questionnaire-Child Report resulted in a three factor, 20-item solution: Emotional Support (9 items), Skeptical Preoccupation (5 items), and Protection/Retaliation (6 items). Each factor demonstrated adequate internal consistency. Construct and concurrent validity of the new measure were supported in comparison to other trauma-specific measures. The Maternal Support Questionnaire-Child Report demonstrated sound psychometric properties. Future research is needed to determine whether the Maternal Support Questionnaire-Child Report provides a more sensitive approximation of maternal support following disclosure of sexual abuse, relative to measures of global parent-child relations and to contextualize discrepancies between mother and child ratings of maternal support.

Electron density measurement in an evolving plasma. Experimental devices

International Nuclear Information System (INIS)

Consoli, Terenzio; Dagai, Michel

1960-01-01

The experimental devices described here allow the electron density measurements in the 10 16 e/m 3 to 10 20 e/m 3 interval. Reprint of a paper published in Comptes rendus des seances de l'Academie des Sciences, t. 250, p. 1223-1225, sitting of 15 February 1960 [fr

A measure of state persecutory ideation for experimental studies.

Science.gov (United States)

Freeman, Daniel; Pugh, Katherine; Green, Catherine; Valmaggia, Lucia; Dunn, Graham; Garety, Philippa

2007-09-01

Experimental research is increasingly important in developing the understanding of paranoid thinking. An assessment measure of persecutory ideation is necessary for such work. We report the reliability and validity of the first state measure of paranoia: The State Social Paranoia Scale. The items in the measure conform to a recent definition in which persecutory thinking has the 2 elements of feared harm and perpetrator intent. The measure was tested with 164 nonclinical participants and 21 individuals at high risk of psychosis with attenuated positive symptoms. The participants experienced a social situation presented in virtual reality and completed the new measure. The State Social Paranoia Scale was found to have excellent internal reliability, adequate test-retest reliability, clear convergent validity as assessed by both independent interviewer ratings and self-report measures, and showed divergent validity with measures of positive and neutral thinking. The measure of paranoia in a recent social situation has good psychometric properties.

submitter Experimental temperature measurements for the energy amplifier test

CERN Document Server

Calero, J; Gallego, E; Gálvez, J; García Tabares, L; González, E; Jaren, J; López, C; Lorente, A; Martínez Val, J M; Oropesa, J; Rubbia, C; Rubio, J A; Saldana, F; Tamarit, J; Vieira, S

1996-01-01

A uranium thermometer has been designed and built in order to make local power measurements in the First Energy Amplifier Test (FEAT). Due to the experimental conditions power measurements of tens to hundreds of nW were required, implying a sensitivity in the temperature change measurements of the order of 1 mK. A uranium thermometer accurate enough to match that sensitivity has been built. The thermometer is able to determine the absolute energetic gain obtained in a tiny subcritical uranium assembly exposed to a proton beam of kinetic energies between 600 MeV and 2.75 GeV. In addition, the thermometer measurements have provided information about the spatial power distribution and the shape of the neutron spallation cascade.

Experimental measurements of the cavitating flow after horizontal water entry

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Thang Tat; Thai, Nguyen Quang; Phuong, Truong Thi [Institute of Mechanics (IMECH), Vietnam Academy of Science and Technology (VAST), 264—Doi Can, Ba Dinh, Hanoi (Viet Nam); Hai, Duong Ngoc, E-mail: ntthang@imech.vast.vn, E-mail: dnhai@vast.vn, E-mail: nqthai@imech.vast.vn, E-mail: ttphuong@imech.vast.vn [Graduate University of Science and Technology (GUST), VAST, 18—Hoang Quoc Viet, Cau Giay, Hanoi (Viet Nam)

2017-10-15

Water-entry cavitating flow is of considerable importance in underwater high-speed applications. That is because of the drag-reduction effect that concerns the presence of a cavity around moving objects. Though the study of the flow has long been carried out, little data are documented in literature so far. Besides, currently, in the case of unsteady flow, experimental measurements of some flow parameters such as the cavity pressure still encounter difficulties. Hence continuing research efforts are of important significance. The objective of this study is to investigate experimentally the unsteady cavitating flow after the horizontal water entry of projectiles. An experimental apparatus has been developed. Qualitative and quantitative optical visualizations of the flow have been carried out by using high-speed videography. Digital image processing has been applied to analyzing the recorded flow images. Based on the known correlations between the ellipsoidal super-cavity’s size and the corresponding cavitation number, the cavity pressure has been measured by utilizing the data of image processing. A comparison between the partial- and super-cavitating flow regimes is reported. The received results can be useful for the design of high-speed underwater projectiles. (paper)

On the use of fuzzy logics in the operator support system of an experimental facility

International Nuclear Information System (INIS)

Mozhaev, A.A.

1988-01-01

Problems of consrtuction of the computerized operator support system of the experimental device are considered on the basis of the imitation decision-making model which uses the fuzzy logic apparatus for a formal description of the decision-making process. 22 refs.; 4 figs.; 2 tabs

Measuring and Analyzing the Scholarly Impact of Experimental Evaluation Initiatives

DEFF Research Database (Denmark)

Angelini, Marco; Ferro, Nicola; Larsen, Birger

2014-01-01

Evaluation initiatives have been widely credited with contributing highly to the development and advancement of information access systems, by providing a sustainable platform for conducting the very demanding activity of comparable experimental evaluation in a large scale. Measuring the impact...

Experimental measurement of proton penetration in silicon

International Nuclear Information System (INIS)

Castaing, C.; Baruch, P.; Picard, C.

1974-01-01

After proton implantation in silicon at high fluence, hydrogen precipitation in bubbles is induced by annealing. The stresses are so high that blister formation and peeling occur, leaving flat bottomed pits, with a depth equal to the projected proton range R(p). In this way R(p) was measured between 200 and 600keV, and compared with already published values, and with values computed through LSS (Lindhard, Scharff, and Schiott) theory, using a correct electronic stopping power. A table of ranges and standard deviations, computed in this way is given. The agreement with experimental results is excellent [fr

45 CFR 270.7 - What data will we use to measure performance on the work support and other measures?

Science.gov (United States)

2010-10-01

... measure performance on the work support and other measures? (a) We will use Census Bureau data to rank... 45 Public Welfare 2 2010-10-01 2010-10-01 false What data will we use to measure performance on the work support and other measures? 270.7 Section 270.7 Public Welfare Regulations Relating to Public...

Some observations on precipitation measurement on forested experimental watersheds

Science.gov (United States)

Raymond E. Leonard; Kenneth G. Reinhart

1963-01-01

Measurement of precipitation on forested experimental watersheds presents difficulties other than those associated with access to and from the gages in all kinds of weather. For instance, the tree canopy must be cleared above the gage. The accepted practice of keeping an unobstructed sky view of 45" around the gage involves considerable tree cutting. On a level...

Experimental research of digital holographic microscopic measuring

Science.gov (United States)

Zhu, Xueliang; Chen, Feifei; Li, Jicheng

2013-06-01

Digital holography is a new imaging technique, which is developed on the base of optical holography, Digital processing, and Computer techniques. It is using CCD instead of the conventional silver to record hologram, and then reproducing the 3D contour of the object by the way of computer simulation. Compared with the traditional optical holographic, the whole process is of simple measuring, lower production cost, faster the imaging speed, and with the advantages of non-contact real-time measurement. At present, it can be used in the fields of the morphology detection of tiny objects, micro deformation analysis, and biological cells shape measurement. It is one of the research hot spot at home and abroad. This paper introduced the basic principles and relevant theories about the optical holography and Digital holography, and researched the basic questions which influence the reproduce images in the process of recording and reconstructing of the digital holographic microcopy. In order to get a clear digital hologram, by analyzing the optical system structure, we discussed the recording distance and of the hologram. On the base of the theoretical studies, we established a measurement and analyzed the experimental conditions, then adjusted them to the system. To achieve a precise measurement of tiny object in three-dimension, we measured MEMS micro device for example, and obtained the reproduction three-dimensional contour, realized the three dimensional profile measurement of tiny object. According to the experiment results consider: analysis the reference factors between the zero-order term and a pair of twin-images by the choice of the object light and the reference light and the distance of the recording and reconstructing and the characteristics of reconstruction light on the measurement, the measurement errors were analyzed. The research result shows that the device owns certain reliability.

Experimental measurements and prediction of liquid densities for n-alkane mixtures

International Nuclear Information System (INIS)

Ramos-Estrada, Mariana; Iglesias-Silva, Gustavo A.; Hall, Kenneth R.

2006-01-01

We present experimental liquid densities for n-pentane, n-hexane and n-heptane and their binary mixtures from (273.15 to 363.15) K over the entire composition range (for the mixtures) at atmospheric pressure. A vibrating tube densimeter produces the experimental densities. Also, we present a generalized correlation to predict the liquid densities of n-alkanes and their mixtures. We have combined the principle of congruence with the Tait equation to obtain an equation that uses as variables: temperature, pressure and the equivalent carbon number of the mixture. Also, we present a generalized correlation for the atmospheric liquid densities of n-alkanes. The average absolute percentage deviation of this equation from the literature experimental density values is 0.26%. The Tait equation has an average percentage deviation of 0.15% from experimental density measurements

Experimental study of tube/support impact forces in multi-span PWR steam generator tubes

International Nuclear Information System (INIS)

Axisa, F.; Desseaux, A.; Gibert, R.J.

1984-12-01

The vibro-impact response of a straight part of a steam generator tube is investigated experimentally and using numerical simulation with the aim to relate tube overall dynamics with excitation and tube-support clearance. Configuration studied here corresponds to the tube being excited in only one direction at its first resonance presenting an antinode of vibration at the impacted support. Tests show namely that midspan displacement of tube is almost proportional to excitation level and clearance. Impact forces averaged over a cycle of vibration are almost proportional to excitation and poorly dependent on clearance. Results of numerical simulation are in fairly good agreement with test results

Theoretical background and experimental measurements of human brain noise intensity in perception of ambiguous images

International Nuclear Information System (INIS)

Runnova, Anastasiya E.; Hramov, Alexander E.; Grubov, Vadim V.; Koronovskii, Alexey A.; Kurovskaya, Maria K.; Pisarchik, Alexander N.

2016-01-01

We propose a theoretical approach associated with an experimental technique to quantitatively characterize cognitive brain activity in the perception of ambiguous images. Based on the developed theoretical background and the obtained experimental data, we introduce the concept of effective noise intensity characterizing cognitive brain activity and propose the experimental technique for its measurement. The developed theory, using the methods of statistical physics, provides a solid experimentally approved basis for further understanding of brain functionality. The rather simple way to measure the proposed quantitative characteristic of the brain activity related to the interpretation of ambiguous images will hopefully become a powerful tool for physicists, physiologists and medics. Our theoretical and experimental findings are in excellent agreement with each other.

The effect of a social support boosting intervention on stress, coping, and social support in caregivers of children with HIV/AIDS.

Science.gov (United States)

Hansell, P S; Hughes, C B; Caliandro, G; Russo, P; Budin, W C; Hartman, B; Hernandez, O C

1998-01-01

Caring for the human immunodeficiency virus (HIV)-infected child is challenging and affects the entire family system. Studies have shown that social support can mitigate caregiver stress and enhance coping; however, social support may not always result in a positive outcome for the recipient. To measure caregiver stress, coping, and social support, and to test the effect of a social support boosting intervention on levels of stress, coping, and social support among caregivers of children with HIV/acquired immune deficiency syndrome (AIDS). An experimental design was used with monthly social support boosting interventions implemented. The stratified randomized sample included 70 primary caregivers of children with HIV/AIDS. The sample strata were seropositive caregivers (biological parents) and seronegative caregivers (foster parents and extended family members). Study measures included the Derogatis Stress Profile, Family Crisis Oriented Personal Evaluation Scale, and the Tilden Interpersonal Relationship Inventory. Data were analyzed using descriptive statistics and repeated measure MANOVA. Statistically significant differences between the experimental and control groups were found on changes in the dependent variables over time when caregiver strata were included as a factor in the analysis; no statistically significant results were found when caregiver strata were combined. Univariate Ftests indicated that the level of social support for caregivers who were seronegative in the experimental group was significantly different from seronegative caregivers in the control group and seropositive caregivers in both groups. No significant treatment group differences were found for seropositive caregivers. Seronegative caregivers derived substantial benefit from the social support boosting intervention. Seronegative caregivers who acquire a child with HIV/AIDS are confronted with a complex stressful situation; the critical need to enhance their social support is

Experimental Method for Measuring Dust Load on Surfaces in Rooms

DEFF Research Database (Denmark)

Lengweiler, Philip; Nielsen, Peter V.; Moser, Alfred

A new experimental setup to investigate the physical process of dust deposition and resuspension on and from surfaces is introduced. Dust deposition can reduce the airborne dust concentration considerably. As a basis for developing methods to eliminate dust-related problems in rooms, there is a n......A new experimental setup to investigate the physical process of dust deposition and resuspension on and from surfaces is introduced. Dust deposition can reduce the airborne dust concentration considerably. As a basis for developing methods to eliminate dust-related problems in rooms......, there is a need for better understanding of the mechanism of dust deposition and resuspension. With the presented experimental setup, the dust load on surfaces in a channel can be measured as a function of the environmental and surface conditions and the type of particles under controlled laboratory conditions....

Experimental solubility measurements of lanthanides in liquid alkalis

Science.gov (United States)

Isler, Jeremy; Zhang, Jinsuo; Mariani, Robert; Unal, Cetin

2017-11-01

In metallic nuclear fuel, lanthanide fission products play a crucial role in the fuel burnup-limiting phenomena of fuel cladding-chemical interaction (FCCI). The lanthanides have been hypothesized to transport by a 'liquid-like' mechanism out of the metallic fuel to the fuel peripheral to cause FCCI. By liquid fission product cesium and liquid bond sodium, the lanthanides are transported to the peripheral of the fuel through the porosity of the fuel. This work investigates the interaction between the lanthanides and the alkali metals by experimentally measuring the solubility of lanthanides within liquid sodium, and neodymium in liquid cesium and mixtures of cesium and sodium. The temperature dependence of the solubility is experimentally determined within an inert environment. In addition, the dependence of the solubility on the alkali metal concentration in liquid mixtures of cesium and sodium was examined. In quantifying the solubility, the fundamental understanding of this transport mechanism can be better determined.

Experimental verification of neutron emission method for measuring of fissile material content in spent fuel

International Nuclear Information System (INIS)

Abou-Zaid, A.A.; Pytel, K.

1999-01-01

A non-destructive method of measurement of fissile nuclides content remained in spent fuel from research reactor is presented. The method, called the neutron emission one, is based on counting of fission neutrons emitted from fissile isotopes: 235 U, 239 Pu, 241 Pu. Fissions are induced mainly by neutrons supplied by the external neutron source. Another effects contribute also to the measured neutron population, e. g. source neutrons from penetrating the fuel without being captured and scattered, neutrons (α,n) reactions and from spontaneous fissions of actinides. Complexity of phenomena occurring within the measurement facility required the detailed numerical simulation and experimental studies prior design of ultimate measurement stand. In the previous paper, the results of Monte Carlo simulation on optimisation of measuring stand for neutron emission method were presented. On the basis of those results, the experimental stand for Maria reactor fuel investigation has been designed and manufactured. The present paper, being the continuation of previous one, contains the description of experimental facility and the results of measurements for the fresh fuel (without burnup) and the fuel mock-up (without fissile materials). Although some discrepancies were found between Monte Carlo and experimental results, the main conclusions concerning the optimal geometry of measuring facility have been confirmed. (author)

Experimental study on two-dimensional film flow with local measurement methods

Energy Technology Data Exchange (ETDEWEB)

Yang, Jin-Hwa, E-mail: evo03@snu.ac.kr [Nuclear Thermal-Hydraulic Engineering Laboratory, Seoul National University, Gwanak 599, Gwanak-ro, Gwanak-gu, Seoul 151-742 (Korea, Republic of); Korea Atomic Energy Research Institute, 989-111, Daedeok-daero, Yuseong-gu, Daejeon 305-600 (Korea, Republic of); Cho, Hyoung-Kyu [Nuclear Thermal-Hydraulic Engineering Laboratory, Seoul National University, Gwanak 599, Gwanak-ro, Gwanak-gu, Seoul 151-742 (Korea, Republic of); Kim, Seok [Korea Atomic Energy Research Institute, 989-111, Daedeok-daero, Yuseong-gu, Daejeon 305-600 (Korea, Republic of); Euh, Dong-Jin, E-mail: djeuh@kaeri.re.kr [Korea Atomic Energy Research Institute, 989-111, Daedeok-daero, Yuseong-gu, Daejeon 305-600 (Korea, Republic of); Park, Goon-Cherl [Nuclear Thermal-Hydraulic Engineering Laboratory, Seoul National University, Gwanak 599, Gwanak-ro, Gwanak-gu, Seoul 151-742 (Korea, Republic of)

2015-12-01

Highlights: • An experimental study on the two-dimensional film flow with lateral air injection was performed. • The ultrasonic thickness gauge was used to measure the local liquid film thickness. • The depth-averaged PIV (Particle Image Velocimetry) method was applied to measure the local liquid film velocity. • The uncertainty of the depth-averaged PIV was quantified with a validation experiment. • Characteristics of two-dimensional film flow were classified following the four different flow patterns. - Abstract: In an accident condition of a nuclear reactor, multidimensional two-phase flows may occur in the reactor vessel downcomer and reactor core. Therefore, those have been regarded as important issues for an advanced thermal-hydraulic safety analysis. In particular, the multi-dimensional two-phase flow in the upper downcomer during the reflood phase of large break loss of coolant accident appears with an interaction between a downward liquid and a transverse gas flow, which determines the bypass flow rate of the emergency core coolant and subsequently, the reflood coolant flow rate. At present, some thermal-hydraulic analysis codes incorporate multidimensional modules for the nuclear reactor safety analysis. However, their prediction capability for the two-phase cross flow in the upper downcomer has not been validated sufficiently against experimental data based on local measurements. For this reason, an experimental study was carried out for the two-phase cross flow to clarify the hydraulic phenomenon and provide local measurement data for the validation of the computational tools. The experiment was performed in a 1/10 scale unfolded downcomer of Advanced Power Reactor 1400 (APR1400). Pitot tubes, a depth-averaged PIV method and ultrasonic thickness gauge were applied for local measurement of the air velocity, the liquid film velocity and the liquid film thickness, respectively. The uncertainty of the depth-averaged PIV method for the averaged

Experimental study on two-dimensional film flow with local measurement methods

International Nuclear Information System (INIS)

Yang, Jin-Hwa; Cho, Hyoung-Kyu; Kim, Seok; Euh, Dong-Jin; Park, Goon-Cherl

2015-01-01

Highlights: • An experimental study on the two-dimensional film flow with lateral air injection was performed. • The ultrasonic thickness gauge was used to measure the local liquid film thickness. • The depth-averaged PIV (Particle Image Velocimetry) method was applied to measure the local liquid film velocity. • The uncertainty of the depth-averaged PIV was quantified with a validation experiment. • Characteristics of two-dimensional film flow were classified following the four different flow patterns. - Abstract: In an accident condition of a nuclear reactor, multidimensional two-phase flows may occur in the reactor vessel downcomer and reactor core. Therefore, those have been regarded as important issues for an advanced thermal-hydraulic safety analysis. In particular, the multi-dimensional two-phase flow in the upper downcomer during the reflood phase of large break loss of coolant accident appears with an interaction between a downward liquid and a transverse gas flow, which determines the bypass flow rate of the emergency core coolant and subsequently, the reflood coolant flow rate. At present, some thermal-hydraulic analysis codes incorporate multidimensional modules for the nuclear reactor safety analysis. However, their prediction capability for the two-phase cross flow in the upper downcomer has not been validated sufficiently against experimental data based on local measurements. For this reason, an experimental study was carried out for the two-phase cross flow to clarify the hydraulic phenomenon and provide local measurement data for the validation of the computational tools. The experiment was performed in a 1/10 scale unfolded downcomer of Advanced Power Reactor 1400 (APR1400). Pitot tubes, a depth-averaged PIV method and ultrasonic thickness gauge were applied for local measurement of the air velocity, the liquid film velocity and the liquid film thickness, respectively. The uncertainty of the depth-averaged PIV method for the averaged

Development of an Experimental Measurement System for Human Error Characteristics and a Pilot Test

International Nuclear Information System (INIS)

Jang, Tong-Il; Lee, Hyun-Chul; Moon, Kwangsu

2017-01-01

Some items out of individual and team characteristics were partially selected, and a pilot test was performed to measure and evaluate them using the experimental measurement system of human error characteristics. It is one of the processes to produce input data to the Eco-DBMS. And also, through the pilot test, it was tried to take methods to measure and acquire the physiological data, and to develop data format and quantification methods for the database. In this study, a pilot test to measure the stress and the tension level, and team cognitive characteristics out of human error characteristics was performed using the human error characteristics measurement and experimental evaluation system. In an experiment measuring the stress level, physiological characteristics using EEG was measured in a simulated unexpected situation. As shown in results, although this experiment was pilot, it was validated that relevant results for evaluating human error coping effects of workers’ FFD management guidelines and unexpected situation against guidelines can be obtained. In following researches, additional experiments including other human error characteristics will be conducted. Furthermore, the human error characteristics measurement and experimental evaluation system will be utilized to validate various human error coping solutions such as human factors criteria, design, and guidelines as well as supplement the human error characteristics database.

Using the analysis of stress waves to build research for experimentation on ultrasonic film measurement

Science.gov (United States)

Chang, Shi-Shing; Wu, John H.

1993-09-01

After the 2th world war, although the application of ultrasonic wave in industries is becoming more and more popular. But due to the restriction of the precise equivelent , experimental method and the support of the basic theoremsetc. Ultrasonic wave is not applied in precise measurement. Nowadays due to many conditions - the improvement in the production technic, the precise of the equivelent, causes to increase the application of ultrasonic wave. But it's still limited due to the lack of measurement and analysis theorem. In this paper, first we caculate translation of the stress wave (elastic wave) in material for the free surface of material by a normal impulse load. as the theorem analysis base in real application. It is applied to an experiment of film measurement. We can find the partical motion in material and the arriving time of wave front. Then we can estimate the thickness of layers and can prove the actual condition with the result of experiment. This resarch is not only in the theoretical investigation but also in setting overall the measurement system, and excutes the following three experiments: the thickness measurement of two layers, the thickness measurement of film material. the thickness measurement of air propagation. About the data processing, we relied on the frequency analysis to evalute the time difference of two overlapped ultrasonic wave signal. in the meanwhile. we also designed several computer programs to assist the sonic wave identification and signal analysis.

Wild Vervet Monkeys Trade Tolerance and Specific Coalitionary Support for Grooming in Experimentally Induced Conflicts.

Science.gov (United States)

Borgeaud, Christèle; Bshary, Redouan

2015-11-16

Grooming is a key social behavior in many primate species. Research has focused on three important aspects: the short- and long-term trading patterns of grooming for itself and/or for other commodities like tolerance or coalitionary support, the issue of whether exchanges are a convincing example for reciprocity, and what decision rules underlie trading. These issues remain largely unresolved due to the correlative nature of observational studies and the rarity of experimental studies. Here, we present a new experimental paradigm to address these questions in wild vervet monkeys (Chlorocebus pygerythrus). Adult females were first trained to approach a personal box, identifiable by unique color patterns, to access high-quality food. During the experiments, two boxes were placed next to each other to induce conflict through forced proximity. We found that while dominants were generally more tolerant toward bonded individuals, recent grooming increased tolerance independently of relationship quality. The latter result shows that vervet monkeys traded grooming for short-term tolerance, where dominants used a direct-reciprocity decision rule. In contrast, females invariably supported the higher-ranking opponent in a conflict, independently of who was the recent grooming partner. Nevertheless, recent grooming increased the probability that a female supported the partner during conflicts with a low-ranking third party. Thus, females' decisions about coalitionary support seem to integrate information about the current social hierarchy with recent grooming events. In conclusion, decision rules underlying trading of grooming for other commodities involve a variety of timescales and factors. Copyright © 2015 Elsevier Ltd. All rights reserved.

Heat Flow Measurements on Beam Screens with and without Supports

CERN Document Server

Bozzini, D; Darve, C; Jenninger, B; Kos, N; Willems, D

1999-01-01

The thermal resistance between LHC beam screens and cold bores has been measured on two 10 m long models in the Cryostat Thermal Model (CTM). One beam screen was equipped with stainless steel spring supports and one had no supports and was inserted in a cold bore with reduced diameter. For both beam screens the heat load to the cold bore was well within the LHC budget that is allocated for the beam screen support system.

Experimental Test of Entropic Noise-Disturbance Uncertainty Relations for Spin-1/2 Measurements.

Science.gov (United States)

Sulyok, Georg; Sponar, Stephan; Demirel, Bülent; Buscemi, Francesco; Hall, Michael J W; Ozawa, Masanao; Hasegawa, Yuji

2015-07-17

Information-theoretic definitions for noise and disturbance in quantum measurements were given in [Phys. Rev. Lett. 112, 050401 (2014)] and a state-independent noise-disturbance uncertainty relation was obtained. Here, we derive a tight noise-disturbance uncertainty relation for complementary qubit observables and carry out an experimental test. Successive projective measurements on the neutron's spin-1/2 system, together with a correction procedure which reduces the disturbance, are performed. Our experimental results saturate the tight noise-disturbance uncertainty relation for qubits when an optimal correction procedure is applied.

Experimental demonstration of the finite measurement time effect on the Feynman-{alpha} technique

Energy Technology Data Exchange (ETDEWEB)

Wallerbos, E.J.M.; Hoogenboom, J.E

1998-09-01

The reactivity of a subcritical system is determined by fitting two different theoretical models to a measured Feynman-{alpha} curve. The first model is the expression usually found in the literature, which can be shown to be the expectation value of the experimental quality if the measurement time is infinite. The second model is a new expression which is the expectation value of the experimental quantity for a finite measurement time. The reactivity inferred with the new model is seen to be independent of the length of the fitting interval, whereas the reactivity inferred with the conventional model is seen to vary. This difference demonstrates the effect of the finite measurement time. As a reference, the reactivity is also measured with the pulsed-neutron source method. It is seen to be in good agreement with the reactivity obtained with the Feynman-{alpha} technique when the new expression is applied.

Experimental ion mobility measurements in Xe-CO2

Science.gov (United States)

Cortez, A. F. V.; Santos, M. A. G.; Veenhof, R.; Patra, R. N.; Neves, P. N. B.; Santos, F. P.; Borges, F. I. G. M.; Conde, C. A. N.

2017-06-01

Data on ion mobility is important to improve the performance of large volume gaseous detectors. In the present work the method, experimental setup and results for the ion mobility measurements in Xe-CO2 mixtures are presented. The results for this mixture show the presence of only one peak for all gas ratios of Xe-CO2, low reduced electric fields, E/N, 10-25 Td (2.4-6.1 kV·cm-1·bar-1), low pressures 6-8 Torr (8-10.6 mbar), at room temperature.

Experimental validation of error in temperature measurements in thin walled ductile iron castings

DEFF Research Database (Denmark)

Pedersen, Karl Martin; Tiedje, Niels Skat

2007-01-01

An experimental analysis has been performed to validate the measurement error of cooling curves measured in thin walled ductile cast iron. Specially designed thermocouples with Ø0.2 mm thermocouple wire in Ø1.6 mm ceramic tube was used for the experiments. Temperatures were measured in plates...

Experimental comparison of particle interaction measurement techniques using optical traps

International Nuclear Information System (INIS)

Koehler, Timothy P.; Grillet, Anne Mary; Brotherton, Christopher M.; Molecke, Ryan A.

2008-01-01

Optical tweezers has become a powerful and common tool for sensitive determination of electrostatic interactions between colloidal particles. Recently, two techniques, 'blinking' tweezers and direct force measurements, have become increasingly prevalent in investigations of inter-particle potentials. The 'blinking' tweezers method acquires physical statistics of particle trajectories to determine drift velocities, diffusion coefficients, and ultimately colloidal forces as a function of the center-center separation of two particles. Direct force measurements monitor the position of a particle relative to the center of an optical trap as the separation distance between two continuously trapped particles is gradually decreased. As the particles near each other, the displacement from the trap center for each particle increases proportional to the inter-particle force. Although commonly employed in the investigation of interactions of colloidal particles, there exists no direct comparison of these experimental methods in the literature. In this study, an experimental apparatus was developed capable of performing both methods and is used to quantify electrostatic potentials between particles in several particle/solvent systems. Comparisons are drawn between the experiments conducted using the two measurement techniques, theory, and existing literature. Forces are quantified on the femto-Newton scale and results agree well with literature values

Low-Speed Model Support Interference - Elements of an Expert System

NARCIS (Netherlands)

Horsten, B.J.C.

2011-01-01

Wind tunnel support interference is one of the constraints affecting the quality of wind tunnel measurements. Several methods to determine the interference are experimental- empirical- and numerical methods. Experimental methods are often time consuming and costly. This also holds for empirical

Developing the Pieta House Suicide Intervention Model: a quasi-experimental, repeated measures design.

Science.gov (United States)

Surgenor, Paul Wg; Freeman, Joan; O'Connor, Cindy

2015-01-01

While most crisis intervention models adhere to a generalised theoretical framework, the lack of clarity around how these should be enacted has resulted in a proliferation of models, most of which have little to no empirical support. The primary aim of this research was to propose a suicide intervention model that would resolve the client's suicidal crisis by decreasing their suicidal ideation and improve their outlook through enhancing a range of protective factors. The secondary aim was to assess the impact of this model on negative and positive outlook. A quasi-experimental, pre-test post-test repeated measures design was employed. A questionnaire assessing self-esteem, depression, and positive and negative suicidal ideation was administered to the same participants pre- and post- therapy facilitating paired responses. Multiple analysis of variance and paired-samples t-tests were conducted to establish whether therapy using the PH-SIM had a significant effect on the clients' negative and positive outlook. Analyses revealed a statistically significant effect of therapy for depression, negative suicidal ideation, self-esteem, and positive suicidal ideation. Negative outlook was significantly lower after therapy and positive outlook significantly higher. The decreased negative outlook and increased positive outlook following therapy provide some support for the proposed model in fulfilling its role, though additional research is required to establish the precise role of the intervention model in achieving this.

Measuring nursing support during childbirth.

Science.gov (United States)

Gale, J; Fothergill-Bourbonnais, F; Chamberlain, M

2001-01-01

To examine the amount of support being provided by nurses to women during childbirth and factors that influence the provision of support. Exploratory, descriptive. Work sampling method was used to determine the percentage of time nurses spend in supportive care activities. Twelve nurses were observed over six nonconsecutive day shifts on a birthing unit of a Canadian teaching hospital in Quebec. A total of 404 observations were made. Nurses were also interviewed to determine their perceptions of what constitutes supportive nursing care and the factors that facilitate or inhibit the provision of this care. Nurses spent only 12.4% of their total time providing supportive care to laboring women. Interviews with nurses suggested that perceptions of the components of supportive care were comparable to this study's operational definition of support, namely: physical, emotional, and instructional/informational support and advocacy. Barriers to providing support identified by nurses included lack of time and insufficient staff. However, further content analysis of the interview data revealed that healthcare providers had a pervasive sense of control over laboring women and their partners. Although nursing support has been identified as an important aspect of nursing care in childbirth, this study demonstrated an incongruity between what nurses perceived as being supportive care and the amount of support that was actually provided. Barriers to the provision of supportive care in the practice setting as well as suggestions for its enhancement are discussed.

Models to support students’ understanding of measuring area of circles

Science.gov (United States)

Rejeki, S.; Putri, R. I. I.

2018-01-01

Many studies showed that enormous students got confused about the concepts of measuring area of circles. The main reason is because mathematics classroom practices emphasized on memorizing formulas rather than understanding concepts. Therefore, in this study, a set of learning activities were designed as an innovation in learning area measurement of circles. The activities involved two models namely grid paper and reshaping which are respectively as a means and a strategy to support students’ learning of area measurement of circles. Design research was used as the research approach to achieve the aim. Thirty-eight of 8th graders in Indonesia were involved in this study. In this study, together with the contextual problems, the grid paper and reshaping sectors, which used as the models in this learning, helped the students to gradually develop their understanding of the area measurement of circles. The grid papers plays important role in comparing and estimating areas. Whereas, the reshaping sectors might support students’ understanding of the circumference and the area measurement of circles. Those two models could be the tool for promoting the informal theory of area measurement. Besides, the whole activities gave important role on distinguishing the area and perimeter of circles.

Experimental Influences in the Accurate Measurement of Cartilage Thickness in MRI.

Science.gov (United States)

Wang, Nian; Badar, Farid; Xia, Yang

2018-01-01

Objective To study the experimental influences to the measurement of cartilage thickness by magnetic resonance imaging (MRI). Design The complete thicknesses of healthy and trypsin-degraded cartilage were measured at high-resolution MRI under different conditions, using two intensity-based imaging sequences (ultra-short echo [UTE] and multislice-multiecho [MSME]) and 3 quantitative relaxation imaging sequences (T 1 , T 2 , and T 1 ρ). Other variables included different orientations in the magnet, 2 soaking solutions (saline and phosphate buffered saline [PBS]), and external loading. Results With cartilage soaked in saline, UTE and T 1 methods yielded complete and consistent measurement of cartilage thickness, while the thickness measurement by T 2 , T 1 ρ, and MSME methods were orientation dependent. The effect of external loading on cartilage thickness is also sequence and orientation dependent. All variations in cartilage thickness in MRI could be eliminated with the use of a 100 mM PBS or imaged by UTE sequence. Conclusions The appearance of articular cartilage and the measurement accuracy of cartilage thickness in MRI can be influenced by a number of experimental factors in ex vivo MRI, from the use of various pulse sequences and soaking solutions to the health of the tissue. T 2 -based imaging sequence, both proton-intensity sequence and quantitative relaxation sequence, similarly produced the largest variations. With adequate resolution, the accurate measurement of whole cartilage tissue in clinical MRI could be utilized to detect differences between healthy and osteoarthritic cartilage after compression.

Sensitivity Measurement of Transmission Computer Tomography: thePreliminary Experimental Study

International Nuclear Information System (INIS)

Widodo, Chomsin-S; Sudjatmoko; Kusminarto; Agung-BS Utomo; Suparta, Gede B

2000-01-01

This paper reports result of preliminary experimental study onmeasurement method for sensitivity of a computed tomography (CT) scanner. ACT scanner has been build at the Department of Physics, FMIPA UGM and itsperformance based on its sensitivity was measured. The result showed that themeasurement method for sensitivity confirmed this method may be developedfurther as a measurement standard. Although the CT scanner developed has anumber of shortcoming, the analytical results from the sensitivitymeasurement suggest a number of reparations and improvements for the systemso that improved reconstructed CT images can be obtained. (author)

Experimental logistics plan in support of Extensive Separations for Hanford tank waste remediation systems

International Nuclear Information System (INIS)

Enderlin, W.I.; Swanson, J.L.; Carlson, C.D.; Hirschi, E.J.

1993-12-01

All proposed methods for remediating the radioactive and chemical waste stored in single- and double-shell tanks (SSTs and DSTs) at the Hanford Site require the separation of the waste mixtures in the tank into high-level and low-level fractions, the safe transport of this separated waste to appropriate immobilization facilities, and the long-term disposal of the immobilized waste forms. Extensive experimentation, especially in waste separations, will be required to develop the technologies and to produce the data that support the most effective and safe cleanup processes. As part of this effort, Pacific Northwest Laboratory (PNL) is developing this detailed experimental logistics plan to determine the logistical/resource requirements, and ultimately the critical paths, necessary to effectively and safely conduct the multitude of experiments within the Extensive Separations Development Program, which addresses the experimental needs of a concept that provides a high degree of separation for the high-level and low-level waste fractions. The logistics issues developed for this program are expected to be similar to those for other programs aimed at remediating and disposing of the wastes

Atomic Physics Measurements in Support of X-ray Astronomy

Science.gov (United States)

Beiersdorfer, Peter; Brown, G. V.; Kelley, R. E.; Kilbourne, C. A.; Leutenegger, M.; Porter, F. S.; Obst, M.; Lepson, J. K.; Desai, P.; Gu, M. F.

2010-10-01

X-ray astronomy has been a voracious consumer of atomic data, especially after the launch of the Chandra and XMM-Newton X-ray Observatories, which have produced very high-resolution grating spectra of point sources. One of the important issues has been to understand the physics underlying the Fe L-shell spectra, and the Fe XVII spectrum in particular. A lot of progress has been made, including measurements of the electron-impact and resonance excitation cross sections, which now provides a rather clear picture of the production mechanism of the Fe XVII spectrum. Recent measurements of the radiative rates provide additional information on the deexcitation channels, while investigations of dielectronic satellite transitions provide a measure of the electron temperature. Many questions, however, still remain. Work at LLNL was performed under the auspices of DOE under contract DE-AC53-07NA27344 and supported by NASA's APRA program under contracts NNH07AF81I and NNG06WF08I. Part of this work was supported by Chandra Cycle 10 Award AR9-0002X.

Reactivity measurements on an experimental assembly of 4.31 wt % 235U enriched UO2 fuel rods arranged in a shipping cask geometry

International Nuclear Information System (INIS)

Bierman, S.R.

1989-10-01

A research program was initiated for the US Department of Energy (DOE) Sandia National Laboratory Transportation Systems Development Department in 1982 to provide benchmark type experimental criticality data in support of the design and safe operations of nuclear fuel transportation systems. The overall objective of the program is to identify and provide the experimental data needed to form a consistent, firm, and complete data base for verifying calculational models used in the criticality analyses of nuclear transport and related systems. A report, PNL-6205, issued in June 1988 (Bierman 1988) covered measurement results obtained from a series of experimental assemblies (TIC-1, 2, 3 and 4) involving neutron flux traps. The results obtained on a fifth experimental assembly (TIC-5), modeled after a calculational problem of the Organization for Economic Cooperation and Development (OECD) Nuclear Energy Agency (NEA) Committee on the Safety of Nuclear Installations (CSNI) Working Group, are covered in this report. 10 refs., 10 figs., 7 tabs

Fundamental Drop Dynamics and Mass Transfer Experiments to Support Solvent Extraction Modeling Efforts

International Nuclear Information System (INIS)

Christensen, Kristi; Rutledge, Veronica; Garn, Troy

2011-01-01

In support of the Nuclear Energy Advanced Modeling Simulation Safeguards and Separations (NEAMS SafeSep) program, the Idaho National Laboratory (INL) worked in collaboration with Los Alamos National Laboratory (LANL) to further a modeling effort designed to predict mass transfer behavior for selected metal species between individual dispersed drops and a continuous phase in a two phase liquid-liquid extraction (LLE) system. The purpose of the model is to understand the fundamental processes of mass transfer that occur at the drop interface. This fundamental understanding can be extended to support modeling of larger LLE equipment such as mixer settlers, pulse columns, and centrifugal contactors. The work performed at the INL involved gathering the necessary experimental data to support the modeling effort. A custom experimental apparatus was designed and built for performing drop contact experiments to measure mass transfer coefficients as a function of contact time. A high speed digital camera was used in conjunction with the apparatus to measure size, shape, and velocity of the drops. In addition to drop data, the physical properties of the experimental fluids were measured to be used as input data for the model. Physical properties measurements included density, viscosity, surface tension and interfacial tension. Additionally, self diffusion coefficients for the selected metal species in each experimental solution were measured, and the distribution coefficient for the metal partitioning between phases was determined. At the completion of this work, the INL has determined the mass transfer coefficient and a velocity profile for drops rising by buoyancy through a continuous medium under a specific set of experimental conditions. Additionally, a complete set of experimentally determined fluid properties has been obtained. All data will be provided to LANL to support the modeling effort.

Experimental measurements of out-of-plane vibrations of a simple blisk design using Blade Tip Timing and Scanning LDV measurement methods

Science.gov (United States)

Di Maio, D.; Ewins, D. J.

2012-04-01

The study of dynamic properties of rotating structures, such as bladed discs, can be conveniently done using simple bladed discs where the blades do not have staggering angles. Simplified design, although not truly representative of real structures, can be easy and economic to manufacture and, still, very helpful for studying specific dynamic properties. An example of this can be called as mass mistune blisk study. Experimental measurements of vibrations of bladed discs under rotating conditions can be performed using Scanning Laser Doppler Vibrometer (SLDV) systems. However, in the aerospace industry, the vibrations of complex bladed discs must be measured under operating conditions which are more hostile than laboratory simulations. The Blade Tip Timing (BTT) measurement method is a measurement technique, which can be used to measure vibrations of bladed discs of an engine aircraft under operating conditions. However, the BTT technique is ineffective when used with a flat bladed disc whose blade vibrations cannot be measured. This can be detrimental when the use of controlled dynamic parameters, such as those obtained from a simple bladed disc design, can improve the confidence for the validation of post-processing software. This paper presents a work about experimental measurements of a simple bladed disc design whose vibrations were measured synchronously by Scanning LDV and BTT measurement systems. A rotating test rig and its mechanical modifications for the installation of the BTT probes are introduced. Implications of rotating a specimen inconsistently are presented so as solutions to obtained constant revolving speed. The experimental comparisons of forced response vibrations measured synchronously at one blade are presented and explained.

A new support measure to quantify the impact of local optima in phylogenetic analyses.

KAUST Repository

Brammer, Grant

2011-09-29

Phylogentic analyses are often incorrectly assumed to have stabilized to a single optimum. However, a set of trees from a phylogenetic analysis may contain multiple distinct local optima with each optimum providing different levels of support for each clade. For situations with multiple local optima, we propose p-support which is a clade support measure that shows the impact optima have on a final consensus tree. Our p-support measure is implemented in our PeakMapper software package. We study our approach on two published, large-scale biological tree collections. PeakMapper shows that each data set contains multiple local optima. p-support shows that both datasets contain clades in the majority consensus tree that are only supported by a subset of the local optima. Clades with low p-support are most likely to benefit from further investigation. These tools provide researchers with new information regarding phylogenetic analyses beyond what is provided by other support measures alone.

Understanding key performance indicators for breast support: An analysis of breast support effects on biomechanical, physiological and subjective measures during running.

Science.gov (United States)

Risius, Debbie; Milligan, Alexandra; Berns, Jason; Brown, Nicola; Scurr, Joanna

2017-05-01

To assess the effectiveness of breast support previous studies monitored breast kinematics and kinetics, subjective feedback, muscle activity (EMG), ground reaction forces (GRFs) and physiological measures in isolation. Comparing these variables within one study will establish the key performance variables that distinguish between breast supports during activities such as running. This study investigates the effects of changes in breast support on biomechanical, physiological and subjective measures during running. Ten females (34D) ran for 10 min in high and low breast supports, and for 2 min bare breasted (2.8 m·s -1 ). Breast and body kinematics, EMG, expired air and heart rate were recorded. GRFs were recorded during 10 m overground runs (2.8 m·s -1 ) and subjective feedback obtained after each condition. Of the 62 variables measured, 22 kinematic and subjective variables were influenced by changes in breast support. Willingness to exercise, time lag and superio-inferior breast velocity were most affected. GRFs, EMG and physiological variables were unaffected by breast support changes during running. Breast displacement reduction, although previously advocated, was not the most sensitive variable to breast support changes during running. Instead breast support products should be assessed using a battery of performance indicators, including the key kinematic and subjective variables identified here.

New experimental device for high-temperature normal spectral emissivity measurements of coatings

International Nuclear Information System (INIS)

Honnerová, Petra; Martan, Jiří; Kučera, Martin; Honner, Milan; Hameury, Jacques

2014-01-01

A new experimental device for normal spectral emissivity measurements of coatings in the infrared spectral range from 1.38 μm to 26 μm and in the temperature range from 550 K to 1250 K is presented. A Fourier transform infrared spectrometer (FTIR) is used for the detection of sample and blackbody spectral radiation. Sample heating is achieved by a fiber laser with a scanning head. Surface temperature is measured by two methods. The first method uses an infrared camera and a reference coating with known effective emissivity, the second method is based on the combination of Christiansen wavelength with contact and noncontact surface temperature measurement. Application of the method is shown on the example of a high-temperature high-emissivity coating. Experimental results obtained with this apparatus are compared with the results performed by a direct method of Laboratoire National d’Essais (LNE) in France. The differences in the spectra are analyzed. (paper)

Experimental system to measure excitation cross-sections by electron impact. Measurements for ArI and ArII

International Nuclear Information System (INIS)

Blanco, F.; Sanchez, J.A.; Aguilera, J.A.; Campos, J.

1989-01-01

An experimental set-up to measure excitation cross-section of atomic and molecular levels by electron impact based on the optical method is reported. We also present some measurements on the excitation cross-section for ArI 5p'(1/2)0 level, and for simultaneous ionization and excitation of Ar leading to ArII levels belonging to the 3p 4 4p and 3p 4 4d configurations. (Author)

Experimental platforms in support of the ASTRID program: existing and planned facilities - 15126

International Nuclear Information System (INIS)

Gastaldi, O.; Rodriguez, G.; Ayrault, L.; Collard, B.; Dumesnil, J.; Dujet, F.; Journeau, C.; Latge, C.; Sanseigne, E.; Serre, F.; Tkatschenko, I.; Willermoz, G.

2015-01-01

The sodium cooled fast reactors (SFR) French program currently focused on the design of the ASTRID (Advanced Sodium Technological Reactor for Industrial Demonstration) reactor in different fields: energy conversion system, instrumentation for continuous monitoring, In Service Inspection and Repair, core design, fuel handling, thermo hydraulic, severe accidents, large flow electromagnetic pumps... Even if the French experimental prototype implies the development of innovative techniques, concepts and feedback of operations of SFRs are important, the new challenges coming from the objectives to meet GEN-IV requirements need some research and development. To achieve this goal, the generation four French SFR program includes the development of technological platforms with experimental facilities to develop and evaluate innovative options and also qualify some ASTRID specific components. The needs in terms of development, validation and qualification of techniques, components or systems to be used on ASTRID have been reviewed exhaustively in 2014. It allowed to consolidate or to precise the experimental purposes of the four CEA platforms regrouping technological facilities with different strategy of erection. PAPIRUS platform (largely already constructed) is dedicated to in-sodium experimental testing; GISEH platform (also largely already constructed) is devoted to water and air tests in support to hydraulic, thermal-hydraulic and fluid-structure interaction studies; CHEOPS platform (detailed studies and realization contract launched in 2014 aiming at commissioning and start up in 2018) deals with in sodium research and development and some qualifications requiring large scale; and last, PLINIUS-2 platform (commissioning and start up in 2019) concerns prototypic corium behavior studies in severe accident conditions and mitigation device qualification. This paper presents the four platforms and for each of them the experimental needs which are covered by their facilities

Inverse kinetics technique for reactor shutdown measurement: an experimental assessment. [AGR

Energy Technology Data Exchange (ETDEWEB)

Lewis, T. A.; McDonald, D.

1975-09-15

It is proposed to use the Inverse Kinetics Technique to measure the subcritical reactivity as a function of time during the testing of the nitrogen injection systems on AGRs. A description is given of an experimental assessment of the technique by investigating known transients created by control rod movements on a small experimental reactor, (2m high, 1m radius). Spatial effects were observed close to the moving rods but otherwise derived reactivities were independent of detector position and agreed well with the existing calibrations. This prompted the suggestion that data from installed reactor instrumentation could be used to calibrate CAGR control rods.

A Proposal of a Method to Measure and Evaluate the Effect to Apply External Support Measures for Owners by Construction Management Method, etc

Science.gov (United States)

Tada, Hiroshi; Miyatake, Ichiro; Mouri, Junji; Ajiki, Norihiko; Fueta, Toshiharu

In Japan, various approaches have been taken to ensure the quality of public works or to support the procurement regime of the governmental agencies, as a means to utilize external resources, which include the procurement support service or the construction management (CM) method. Although discussions on these measures to utilize external resources (hereinafter referred to as external support measure) have been going on, as well as the follow-up surveys showing the positive effects of such measures have been conducted, the surveys only deal with the matters concerning the overall effects of the external support measure on the whole, meaning that the effect of each item of the tasks have not been addressed, and that the extent it dealt with the expectations of the client is unknown. However, the effective use of the external support measure in future cannot be achieved without knowing what was the purpose to introduce the external support measure, and what effect was expected on each task item, and what extent the expectation fulfilled. Furthermore, it is important to clarify not only the effect as compared to the client's expectation (performance), but also the public benefit of this measure (value improvement). From this point of view, there is not an established method to figure out the effect of the client's measure to utilize external resources. In view of this background, this study takes the CM method as an example of the external support measure, and proposes a method to measure and evaluate the effect by each task item, and suggests the future issues and possible responses, in the aim of contributing the promotion, improvement, and proper implementation of the external support measures in future.

On the measurement of a weak classical force coupled to a harmonic oscillator: experimental progress

International Nuclear Information System (INIS)

Bocko, M.F.; Onofrio, R.

1996-01-01

Several high-precision physics experiments are approaching a level of sensitivity at which the intrinsic quantum nature of the experimental apparatus is the dominant source of fluctuations limiting the sensitivity of the measurements. This quantum limit is embodied by the Heisenberg uncertainty principle, which prohibits arbitrarily precise simultaneous measurements of two conjugate observables of a system but allows one-time measurements of a single observable with any precision. The dynamical evolution of a system immediately following a measurement limits the class of observables that may be measured repeatedly with arbitrary precision, with the influence of the measurement apparatus on the system being confined strictly to the conjugate observables. Observables having this feature, and the corresponding measurements performed on them, have been named quantum nondemolition or back-action evasion observables. In a previous review (Caves et al., 1980, Rev. Mod. Phys. 52, 341) a quantum-mechanical analysis of quantum nondemolition measurements of a harmonic oscillator was presented. The present review summarizes the experimental progress on quantum nondemolition measurements and the classical models developed to describe and guide the development of practical implementations of quantum nondemolition measurements. The relationship between the classical and quantum theoretical models is also reviewed. The concept of quantum nondemolition and back-action evasion measurements originated in the context of measurements on a macroscopic mechanical harmonic oscillator, though these techniques may be useful in other experimental contexts as well, as is discussed in the last part of this review. copyright 1996 The American Physical Society

Experimental technique to measure thoron generation rate of building material samples using RAD7 detector

International Nuclear Information System (INIS)

Csige, I.; Szabó, Zs.; Szabó, Cs.

2013-01-01

Thoron ( 220 Rn) is the second most abundant radon isotope in our living environment. In some dwellings it is present in significant amount which calls for its identification and remediation. Indoor thoron originates mainly from building materials. In this work we have developed and tested an experimental technique to measure thoron generation rate in building material samples using RAD7 radon-thoron detector. The mathematical model of the measurement technique provides the thoron concentration response of RAD7 as a function of the sample thickness. For experimental validation of the technique an adobe building material sample was selected for measuring the thoron concentration at nineteen different sample thicknesses. Fitting the parameters of the model to the measurement results, both the generation rate and the diffusion length of thoron was estimated. We have also determined the optimal sample thickness for estimating the thoron generation rate from a single measurement. -- Highlights: • RAD7 is used for the determination of thoron generation rate (emanation). • The described model takes into account the thoron decay and attenuation. • The model describes well the experimental results. • A single point measurement method is offered at a determined sample thickness

Design, calculation and experimental studies for liquid metal system main parameters in support of the liquid lithium fusion reactor

International Nuclear Information System (INIS)

Evtikhin, V.A.; Lyublinski, I.E.; Vertkov, A.V.

1999-01-01

A new concept of a Liquid Lithium Fusion Reactor and the first experimental results were presented at the 16th IAEA Conference on Fusion Energy. During the past two years theoretical estimations have been made, and calculated and experimental results have been obtained in confirmation of this concept and supporting its progress. The main results of this work are given in the paper. (author)

Design, calculation and experimental studies for liquid metal system main parameters in support of the liquid lithium fusion reactor

International Nuclear Information System (INIS)

Evtikhin, V.A.; Lyublinski, I.E.; Vertkov, A.V.

2001-01-01

A new concept of a Liquid Lithium Fusion Reactor and the first experimental results were presented at the 16th IAEA Conference on Fusion Energy. During the past two years theoretical estimations have been made, and calculated and experimental results have been obtained in confirmation of this concept and supporting its progress. The main results of this work are given in the paper. (author)

Design of an experimental device dedicated to the measurement of spallation reactions; Mise au point d'un dispositif experimental pour des mesures exclusives des reactions de spallation

Energy Technology Data Exchange (ETDEWEB)

Lafriakh, A

2005-12-15

Spallation mechanisms are not yet completely understood, especially because of the difficulty of experimentally disentangling the effects of the different steps of the reaction. In order to understand these mechanisms, we have developed a new experimental device able to perform inclusive measurements. We propose a detection system based on a combination of ionization chambers and proportional counters and on a wall of plastic scintillators to measure light charged particles. In particular the detection of light charged particles is described in detail. In order to validate our device, we have compared our preliminary results obtained on the Fe{sup 56} + p system at 1 GeV/u with inclusive measurements previously obtained at the FRS spectrometer of the GSI facility. A comparison of charge differential cross section shows reasonable agreement. However, our new device allowed extension of those measurements down to Z = 1 and Z = 2. These cross sections are important for material damage studies. Taking into account our error brackets, the evolution of mean longitudinal velocities with respect to residue masses is comparable to that obtained at the FRS. These first results, although preliminary, allow us to validate our experimental device. It is now possible to exploit the strong points of our exclusive measurements, namely correlations between different measured observables. Finally, experimental problems encountered will be taken into account in the future experimental programs, in order to ensure the best measurements conditions.

Experimental Measurements of Prestressed Masonry with using Sliding Joint

Directory of Open Access Journals (Sweden)

Stara Marie

2014-06-01

Full Text Available Contribution deals with experimental measurements of deformations in the place exposed to local load caused by additional pre-stressing. The measurements are made at the masonry corner built in the laboratory equipment. The laboratory equipment was designed at Faculty of Civil Engineering VŠB-Technical University of Ostrava for measurement tri-axial stress-strain conditions in masonry. In this masonry corner two pre-stressing bars are placed. These bars are in different height and are anchored to the anchor plates, which transfer pre-stressing forces to the masonry. The specimen for laboratory testing is performed in the proportion to the reality of 1:1. In the bottom part masonry is inserted asphalt strip. It operates in the masonry like a sliding joint and reduces the shear stress at interface between concrete and masonry structures. The results are compared with the results of masonry without the use of sliding joints, including comment on the effect of sliding joints on the pre-stressing masonry structures.

Ultrasonic fluid quantity measurement in dynamic vehicular applications a support vector machine approach

CERN Document Server

Terzic, Jenny; Nagarajah, Romesh; Alamgir, Muhammad

2013-01-01

Accurate fluid level measurement in dynamic environments can be assessed using a Support Vector Machine (SVM) approach. SVM is a supervised learning model that analyzes and recognizes patterns. It is a signal classification technique which has far greater accuracy than conventional signal averaging methods. Ultrasonic Fluid Quantity Measurement in Dynamic Vehicular Applications: A Support Vector Machine Approach describes the research and development of a fluid level measurement system for dynamic environments. The measurement system is based on a single ultrasonic sensor. A Support Vector Machines (SVM) based signal characterization and processing system has been developed to compensate for the effects of slosh and temperature variation in fluid level measurement systems used in dynamic environments including automotive applications. It has been demonstrated that a simple ν-SVM model with Radial Basis Function (RBF) Kernel with the inclusion of a Moving Median filter could be used to achieve the high levels...

Are Facebook "Friends" Helpful? Development of a Facebook-Based Measure of Social Support and Examination of Relationships Among Depression, Quality of Life, and Social Support.

Science.gov (United States)

McCloskey, Wilfred; Iwanicki, Sierra; Lauterbach, Dean; Giammittorio, David M; Maxwell, Kendal

2015-09-01

Greater social support is predictive of lower depression and higher quality of life (QOL). However, the way in which social support is provided has changed greatly with the expanding role of social networking sites (e.g., Facebook). While there are numerous anecdotal accounts of the benefits of Facebook-based social support, little empirical evidence exists to support these assertions, and there are no empirically validated measures designed to assess social support provided via this unique social networking medium. This study sought to develop an empirically sound measure of Facebook-based social support (Facebook Measure of Social Support [FMSS]) and to assess how this new measure relates to previously established measures of support and two outcome variables: depression and QOL. Following exploratory factor analysis, the FMSS was determined to assess four factors of social support on Facebook (Perceived, Emotional, Negative, Received/Instrumental). The Negative Support factor on the FMSS was most strongly related to both depression and QOL with magnitudes (and direction of relationships) comparable to a traditional measure of perceived social support. However, two FMSS factors (Received/Instrumental and Perceived) were unrelated to both mental health outcomes. Contrary to expectations, elevations in one FMSS factor (Emotional) was associated with worse symptoms of depression and poorer psychological QOL. When taken together, only the absence of negative social support on Facebook is significantly predictive of mental health functioning. Consequently, those hoping to use Facebook as a medium for reducing depression or improving QOL are unlikely to realize significant therapeutic benefits.

Measurement of social support, community and trust in dentistry

DEFF Research Database (Denmark)

Berthelsen, Hanne; Pejtersen, Jan Hyld; Söderfeldt, Björn

2011-01-01

BACKGROUND AND AIM: Relationships among people at work have previously been found to contribute to the perception of having a good work. The aim of the present paper was to develop scales measuring aspects of social support, trust, and community among dentists, and to evaluate psychometric proper...

Experimental support of the bleed and feed accident management measures for VVER-440/213 type reactors

International Nuclear Information System (INIS)

Szabados, L.

2002-01-01

In the original design of the VVER-440/213 type nuclear power plants event oriented emergency operating procedures (EOP) were implemented. In the last years, however, new symptom based procedures of Westinghouse-type have been developed and partly implemented for the plants in Central Europe including the Paks Nuclear Power Plant. Paper gives a short review of the experiments performed in the PMK-2 facility to study the effectiveness of the bleed and feed strategies and to get experimental data bases for the validation of thermohydraulic system codes like RELAP5, ATHLET and CATHARE.(author)

Experimental ion mobility measurements in Ne-N2

International Nuclear Information System (INIS)

Cortez, A.F.V.; Encarnação, P.M.C.C.; Santos, F.P.; Borges, F.I.G.M.; Conde, C.A.N.; Veenhof, R.; Neves, P.N.B.

2016-01-01

Data on ion mobility is important to improve the performance of large volume gaseous detectors, such as the ALICE TPC or in the NEXT experiment. In the present work the method, experimental setup and results for the ion mobility measurements in Ne-N 2 mixtures are presented. The results for this mixture show the presence of two peaks for different gas ratios of Ne-N 2 , low reduced electric fields, E / N , 10–20 Td (2.4–4.8 kV·cm −1 ·bar −1 ), low pressures 6–8 Torr (8–10.6 mbar) and at room temperature.

Experimental ion mobility measurements in Xe-CH4

Science.gov (United States)

Perdigoto, J. M. C.; Cortez, A. F. V.; Veenhof, R.; Neves, P. N. B.; Santos, F. P.; Borges, F. I. G. M.; Conde, C. A. N.

2017-09-01

Data on ion mobility is important to improve the performance of large volume gaseous detectors. In the present work, the method, experimental setup and results for the ion mobility measurements in Xe-CH4 mixtures are presented. The results for this mixture show the presence of two distinct groups of ions. The nature of the ions depend on the mixture ratio since they are originated by both Xe and CH4. The results here presented were obtained for low reduced electric fields, E/N, 10-25 Td (2.4-6.1 kV ṡ cm-1 ṡ bar-1), at low pressure (8 Torr) (10.6 mbar), and at room temperature.

Social support among heterogeneous partners : an experimental test

NARCIS (Netherlands)

Vogt, Sonja; Weesie, Jeroen

2006-01-01

This paper studies how dyadic social support is affected by heterogeneity of the partners.We distinguish heterogeneity with respect to three parameters: the likelihood of needing support; the benefits from receiving support; and the costs of providing support. Hypotheses are based on a

Theory and experimental verifications of the resonator Q and equivalent electrical parameters due to viscoelastic and mounting supports losses.

Science.gov (United States)

Yong, Yook-Kong; Patel, Mihir S; Tanaka, Masako

2010-08-01

A novel analytical/numerical method for calculating the resonator Q and its equivalent electrical parameters due to viscoelastic, conductivity, and mounting supports losses is presented. The method presented will be quite useful for designing new resonators and reducing the time and costs of prototyping. There was also a necessity for better and more realistic modeling of the resonators because of miniaturization and the rapid advances in the frequency ranges of telecommunication. We present new 3-D finite elements models of quartz resonators with viscoelasticity, conductivity, and mounting support losses. The losses at the mounting supports were modeled by perfectly matched layers (PMLs). A previously published theory for dissipative anisotropic piezoelectric solids was formulated in a weak form for finite element (FE) applications. PMLs were placed at the base of the mounting supports to simulate the energy losses to a semi-infinite base substrate. FE simulations were carried out for free vibrations and forced vibrations of quartz tuning fork and AT-cut resonators. Results for quartz tuning fork and thickness shear AT-cut resonators were presented and compared with experimental data. Results for the resonator Q and the equivalent electrical parameters were compared with their measured values. Good equivalences were found. Results for both low- and high-Q AT-cut quartz resonators compared well with their experimental values. A method for estimating the Q directly from the frequency spectrum obtained for free vibrations was also presented. An important determinant of the quality factor Q of a quartz resonator is the loss of energy from the electrode area to the base via the mountings. The acoustical characteristics of the plate resonator are changed when the plate is mounted onto a base substrate. The base affects the frequency spectra of the plate resonator. A resonator with a high Q may not have a similarly high Q when mounted on a base. Hence, the base is an

The Thermal Hydraulics of Tube Support Fouling in Nuclear Steam Generators

International Nuclear Information System (INIS)

Rummens, Helena E.C.; Rogers, J.T.; Turner, C.W.

2004-01-01

It is hypothesized that the thermal-hydraulic environment plays a role in the fouling of tube supports in nuclear steam generators. Experiments were performed to simulate the thermal-hydraulic environment near various designs of supports. Pressure loss, local velocity, turbulence intensity, and local void fraction were measured to characterize the effect of the support. Fouling mechanisms specific to supports were inferred from these experimental data and from actual steam generator inspection results. An analytical model was developed to predict the rate of particulate deposition on the supports, to better understand the complex processes involved.This paper presents the following set of tools for assessing the fouling propensity of a given support design: (1) proposed fouling mechanisms, (2) criteria for support fouling propensity, (3) correlation of fouling with parameters such as mass flux and quality, (4) descriptions of experimental tools such as flow visualization and measurement of pressure-loss profiles, and (5) analytical tools.An important conclusion from this and our previous work is that the fouling propensity is greater with broached support plates, both trefoil and quatrefoil, than with lattice bar supports and formed bar supports, in which significant cross flows occur

Experimental measurements of the solubility of technetium under near-field conditions

International Nuclear Information System (INIS)

Pilkington, N.J.; Wilkins, J.D.

1988-05-01

The solubility of technetium in contact with hydrated technetium dioxide under near-field conditions has been measured experimentally. The values obtained were changed little by a change in pH or in the filtration method used. The presence of organic degradation products increased slightly the solution concentration of technetium. (author)

The Impact of the Support System’s Kinematic Structure on Selected Kinematic and Dynamic Quantities of an Experimental Crane

Directory of Open Access Journals (Sweden)

Trąbka Arkadiusz

2014-12-01

Full Text Available This paper presents a comparative analysis of two kinematic structures of the support system (with supports with bilateral and unilateral constraints, which were used in an experimental model of a crane. The computational model was developed by using the ADAMS software. The impact of the kinematic structure of the support system on selected kinematic and dynamic values that were recorded during the slewing motion was analysed. It was found, among other things, that an increased number of degrees of freedom of the support system leads to multiple distortions of time characteristics of kinematic and dynamic quantities.

Cross-Layer Measurement on an IEEE 802.11g Wireless Network Supporting MPEG-2 Video Streaming Applications in the Presence of Interference

Directory of Open Access Journals (Sweden)

Alessandro Sona

2010-01-01

Full Text Available The performance of wireless local area networks supporting video streaming applications, based on MPEG-2 video codec, in the presence of interference is here dealt with. IEEE 802.11g standard wireless networks, that do not support QoS in according with IEEE 802.11e standard, are, in particular, accounted for and Bluetooth signals, additive white Gaussian noise, and competitive data traffic are considered as sources of interference. The goal is twofold: from one side, experimentally assessing and correlating the values that some performance metrics assume at the same time at different layers of an IEEE 802.11g WLAN delivering video streaming in the presence of in-channel interference; from the other side, deducing helpful and practical hints for designers and technicians, in order to efficiently assess and enhance the performance of an IEEE 802.11g WLAN supporting video streaming in some suitable setup conditions and in the presence of interference. To this purpose, an experimental analysis is planned following a cross-layer measurement approach, and a proper testbed within a semianechoic chamber is used. Valuable results are obtained in terms of signal-to-interference ratio, packet loss ratio, jitter, video quality, and interference data rate; helpful hints for designers and technicians are finally gained.

Factor Structure and Measurement Invariance of the Need-Supportive Teaching Style Scale for Physical Education.

Science.gov (United States)

Liu, Jing-Dong; Chung, Pak-Kwong

2017-08-01

The purpose of the current study was to examine the factor structure and measurement invariance of a scale measuring students' perceptions of need-supportive teaching (Need-Supportive Teaching Style Scale in Physical Education; NSTSSPE). We sampled 615 secondary school students in Hong Kong, 200 of whom also completed a follow-up assessment two months later. Factor structure of the scale was examined through exploratory structural equation modeling (ESEM). Further, nomological validity of the NSTSSPE was evaluated by examining the relationships between need-supportive teaching style and student satisfaction of psychological needs. Finally, four measurement models-configural, metric invariance, scalar invariance, and item uniqueness invariance-were assessed using multiple group ESEM to test the measurement invariance of the scale across gender, grade, and time. ESEM results suggested a three-factor structure of the NSTSSPE. Nomological validity was supported, and weak, strong, and strict measurement invariance of the NSTSSPE was evidenced across gender, grade, and time. The current study provides initial psychometric support for the NSTSSPE to assess student perceptions of teachers' need-supportive teaching style in physical education classes.

Experimental plasma research project summaries

International Nuclear Information System (INIS)

1992-06-01

This is the latest in a series of Project Summary books going back to 1976 and is the first after a hiatus of several years. They are published to provide a short description of each project supported by the Experimental Plasma Research Branch of the Division of Applied Plasma Physics in the Office of Fusion Energy. The Experimental Plasma Research Branch seeks to provide a broad range of experimental data, physics understanding, and new experimental techniques that contribute to operation, interpretation, and improvement of high temperature plasma as a source of fusion energy. In pursuit of these objectives, the branch supports research at universities, DOE laboratories, other federal laboratories and industry. About 70 percent of the funds expended are spent at universities and a significant function of this program is the training of students in fusion physics. The branch supports small- and medium-scale experimental studies directly related to specific critical plasma issues of the magnetic fusion program. Plasma physics experiments are conducted on transport of particles and energy within plasma and innovative approaches for operating, controlling, and heating plasma are evaluated for application to the larger confinement devices of the magnetic fusion program. New diagnostic approaches to measuring the properties of high temperature plasmas are developed to the point where they can be applied with confidence on the large-scale confinement experiments. Atomic data necessary for impurity control, interpretation of diagnostic data, development of heating devices, and analysis of cooling by impurity ion radiation are obtained. The project summaries are grouped into these three categories of plasma physics, diagnostic development and atomic physics

Experimental measurements in the BYU controlled profile reactor

Energy Technology Data Exchange (ETDEWEB)

Tree, D.R.; Black, D.l.; Rigby, J.R.; McQuay, M.Q.; Webb, B.W. [Brigham Young University, Provo, UT (United States). Dept. of Mechanical Engineering

1998-09-01

Over the past decade the Controlled Profile Reactor (CPR) has been used to obtain extensive combustion data sets. CPR is a small scale (0.2-0.4 MW) combustion facility that has been used to obtain data for model validation, the testing of new combustion concepts, and the development of new combustion instruments. This review of the past ten years of research completed in the CPR includes a description of the reactor and instrumentation used, a summary of three experimental data sets which have been obtained in the reactor, and a description of novel tests and instrumentation. Measurements obtained include gas species, gas temperature, particle velocity, particle size, particle number density, particle-cloud temperature profiles, radiation and total heat flux to the wall, and wall temperatures. Species data include the measurement of CO, CO{sub 2}, NO, NO{sub x}, O{sub 2}, NH{sub 3} and HCN. The three combustion studies included one with natural gas combustion in a swirling flow, and two pulverized-coal combustion studies involving Utah Blind Canyon and Pittsburgh No. 8 coals. Most, but not all of the above measurements were obtained in each study. The second coal study involving the Pittsburgh No. 8 coal contained the most complete set of data and is described in detail. Novel combustion instrumentation includes the use of Coherent Anti-Stokes Raman Spectroscopy (CARS) to measure gas temperature. Novel combustion experiments include the measurement of NO{sub x} and burnout with coal-char blends. The measurements have led to an improved understanding of the combustion process and an understanding of the strengths and weaknesses associated with different aspects of comprehensive combustion models. 67 refs., 26 figs., 9 tabs.

Quantification of tomographic PIV uncertainty using controlled experimental measurements.

Science.gov (United States)

Liu, Ning; Wu, Yue; Ma, Lin

2018-01-20

The goal of this work was to experimentally quantify the uncertainty of three-dimensional (3D) and three-component (3C) velocity measurements using tomographic particle image velocimetry (tomo-PIV). Controlled measurements were designed using tracer particles embedded in a solid sample, and tomo-PIV measurements were performed on the sample while it was moved both translationally and rotationally to simulate various known displacement fields, so the 3D3C displacements measured by tomo-PIV can be directly compared to the known displacements created by the sample. The results illustrated that (1) the tomo-PIV technique was able to reconstruct the 3D3C velocity with an averaged error of 0.8-1.4 voxels in terms of magnitude and 1.7°-1.9° in terms of orientation for the velocity fields tested; (2) view registration (VR) plays a significant role in tomo-PIV, and by reducing VR error from 0.6° to 0.1°, the 3D3C measurement accuracy can be improved by at least 2.5 times in terms of both magnitude and orientation; and (3) the use of additional cameras in tomo-PIV can extend the 3D3C velocity measurement to a larger volume, while maintaining acceptable accuracy. These results obtained from controlled tests are expected to aid the error analysis and the design of tomo-PIV measurements.

Design of an experimental device dedicated to the measurement of spallation reactions; Mise au point d'un dispositif experimental pour des mesures exclusives des reactions de spallation

Energy Technology Data Exchange (ETDEWEB)

Lafriakh, A

2005-12-15

Spallation mechanisms are not yet completely understood, especially because of the difficulty of experimentally disentangling the effects of the different steps of the reaction. In order to understand these mechanisms, we have developed a new experimental device able to perform inclusive measurements. We propose a detection system based on a combination of ionization chambers and proportional counters and on a wall of plastic scintillators to measure light charged particles. In particular the detection of light charged particles is described in detail. In order to validate our device, we have compared our preliminary results obtained on the Fe{sup 56} + p system at 1 GeV/u with inclusive measurements previously obtained at the FRS spectrometer of the GSI facility. A comparison of charge differential cross section shows reasonable agreement. However, our new device allowed extension of those measurements down to Z = 1 and Z = 2. These cross sections are important for material damage studies. Taking into account our error brackets, the evolution of mean longitudinal velocities with respect to residue masses is comparable to that obtained at the FRS. These first results, although preliminary, allow us to validate our experimental device. It is now possible to exploit the strong points of our exclusive measurements, namely correlations between different measured observables. Finally, experimental problems encountered will be taken into account in the future experimental programs, in order to ensure the best measurements conditions.

Support force measures of midsized men in seated positions.

Science.gov (United States)

Bush, Tamara Reid; Hubbard, Robert P

2007-02-01

Two areas not well researched in the field of seating mechanics are the distribution of normal and shear forces, and how those forces change with seat position. The availability of these data would be beneficial for the design and development of office, automotive and medical seats. To increase our knowledge in the area of seating mechanics, this study sought to measure the normal and shear loads applied to segmental supports in 12 seated positions, utilizing three inclination angles and four levels of seat back articulation that were associated with automotive driving positions. Force data from six regions, including the thorax, sacral region, buttocks, thighs, feet, and hand support were gathered using multi-axis load cells. The sample contained 23 midsized subjects with an average weight of 76.7 kg and a standard deviation of 4.2 kg, and an average height of 1745 mm with a standard deviation of 19 mm. Results were examined in terms of seat back inclination and in terms of torso articulation for relationships between seat positions and support forces. Using a repeated measures analysis, significant differences (p<0.05) were identified for normal forces relative to all inclination angles except for forces occurring at the hand support. Other significant differences were observed between normal forces behind the buttocks, pelvis, and feet for torso articulations. Significant differences in the shear forces occurred under the buttocks and posterior pelvis during changes in seat back inclination. Significant differences in shear forces were also identified for torso articulations. These data suggest that as seat back inclination or torso articulation change, significant shifts in force distribution occur.

Theory and experimental study of biased charge collector for measuring HPIB

International Nuclear Information System (INIS)

He Xiaoping; Wang Haiyang; Sun Jianfeng; Yang Hailiang; Qiu Aici; Tang Junping; Li Jingya; Li Hongyu

2004-01-01

Structure of the biased charge collector for measuring HPIB (High-power ion beam) is introduced in this paper. The inner charge propagation process of HPIB in the biased charge collector was simulated with KARAT PIC code. The simulation results indicated that charge was neutralized but current was not neutralized in the biased charge collector. The influence of biased voltage and aperture diameter were also simulated. A -800V biased voltage can meet the requirement for measuring 500 keV HPIB, and this is consistent with the experimental results

Coherent versus incoherent resonant emission: an experimental method for easy discrimination and measurement

Science.gov (United States)

Ceccherini, S.; Colocci, M.; Gurioli, M.; Bogani, F.

1998-11-01

The distinction between the coherent and the incoherent component of the radiation emitted from resonantly excited material systems is difficult experimentally, particularly when ultra-short optical pulses are used for excitation. We propose an experimental procedure allowing an easy measurement of the two components. The method is completely general and applicable to any kind of physical system; its feasibility is demonstrated on the resonant emission from excitons in a semiconductor quantum well.

Development of a Model for Measuring Scientific Processing Skills Based on Brain-Imaging Technology: Focused on the Experimental Design Process

Science.gov (United States)

Lee, Il-Sun; Byeon, Jung-Ho; Kim, Young-shin; Kwon, Yong-Ju

2014-01-01

The purpose of this study was to develop a model for measuring experimental design ability based on functional magnetic resonance imaging (fMRI) during biological inquiry. More specifically, the researchers developed an experimental design task that measures experimental design ability. Using the developed experimental design task, they measured…

A Review of the Experimental and Modeling Development of a Water Phase Change Heat Exchanger for Future Exploration Support Vehicles

Science.gov (United States)

Cognata, Thomas; Leimkuehler, Thomas; Ramaswamy, Balasubramaniam; Nayagam, Vedha; Hasan, Mohammad; Stephan, Ryan

2011-01-01

Water affords manifold benefits for human space exploration. Its properties make it useful for the storage of thermal energy as a Phase Change Material (PCM) in thermal control systems, in radiation shielding against Solar Particle Events (SPE) for the protection of crew members, and it is indisputably necessary for human life support. This paper envisions a single application for water which addresses these benefits for future exploration support vehicles and it describes recent experimental and modeling work that has been performed in order to arrive at a description of the thermal behavior of such a system. Experimental units have been developed and tested which permit the evaluation of the many parameters of design for such a system with emphasis on the latent energy content, temperature rise, mass, and interstitial material geometry. The experimental results are used to develop a robust and well correlated model which is intended to guide future design efforts toward the multi-purposed water PCM heat exchanger envisioned.

Assessing the validity of measures of an instrument designed to measure employees' perceptions of workplace breastfeeding support.

Science.gov (United States)

Greene, Sally W; Wolfe, Edward W; Olson, Beth H

2008-09-01

Breastfeeding rates among working mothers are lower than among mothers who are not employed. An ecological framework suggests that health behaviors, such as breastfeeding, are influenced by intrapersonal and environmental factors. There is no existing instrument to measure women's perception of the workplace environment in providing breastfeeding support. The objective of this study was to pilot an instrument measuring perceptions of the work climate for breastfeeding support among working women. Data were collected from self-administered mailed questionnaires filled out by 104 pregnant women or women who had recently given birth and were employed and breastfeeding. Dimensionally analyses supported the two-dimensional model suggested by the literature. Internal consistency reliability coefficients were high (near 0.90), and the correlation between the subscales was moderately strong (0.68). Only a single item exhibited misfit to the scaling model, and that item was revised after review.

Progress in nuclear measuring and experimental techniques by application of microelectronics. 1

International Nuclear Information System (INIS)

Meiling, W.

1984-01-01

In the past decade considerable progress has been made in nuclear measuring and experimental techniques by developing position-sensitive detector systems and widely using integrated circuits and microcomputers for data acquisition and processing as well as for automation of measuring processes. In this report which will be published in three parts those developments are reviewed and demonstrated on selected examples. After briefly characterizing microelectronics, the use of microelectronic elements for radiation detectors is reviewed. (author)

Support of the extremal measure in a vector equilibrium problem

International Nuclear Information System (INIS)

Lapik, M A

2006-01-01

A generalization of the Mhaskar-Saff functional is obtained for a vector equilibrium problem with an external field. As an application, the supports of the equilibrium measures are found in a special vector equilibrium problem with Nikishin matrix.

Experimental sources of variation in avian energetics: estimated basal metabolic rate decreases with successive measurements.

Science.gov (United States)

Jacobs, Paul J; McKechnie, Andrew E

2014-01-01

Basal metabolic rate (BMR) is one of the most widely used metabolic variables in endotherm ecological and evolutionary physiology. Surprisingly few studies have investigated how BMR is influenced by experimental and analytical variables over and above the standardized conditions required for minimum normothermic resting metabolism. We tested whether avian BMR is affected by habituation to the conditions experienced during laboratory gas exchange measurements by measuring BMR five times in succession in budgerigars (Melopsittacus undulatus) housed under constant temperature and photoperiod. Both the magnitude and the variability of BMR decreased significantly with repeated measurements, from 0.410 ± 0.092 W (n = 9) during the first measurement to 0.285 ± 0.042 W (n = 9) during the fifth measurement. Thus, estimated BMR decreased by ∼30% within individuals solely on account of the number of times they had previously experienced the experimental conditions. The most likely explanation for these results is an attenuation with repeated exposure of the acute stress response induced by birds being handled and placed in respirometry chambers. Our data suggest that habituation to experimental conditions is potentially an important determinant of observed BMR, and this source of variation needs to be taken into account in future studies of metabolic variation among individuals, populations, and species.

Experimental Measurement of In Situ Stress

Science.gov (United States)

Tibbo, Maria; Milkereit, Bernd; Nasseri, Farzine; Schmitt, Douglas; Young, Paul

2016-04-01

The World Stress Map data is determined by stress indicators including earthquake focal mechanisms, in situ measurement in mining, oil and gas boreholes as well as the borehole cores, and geologic data. Unfortunately, these measurements are not only infrequent but sometimes infeasible, and do not provide nearly enough data points with high accuracy to correctly infer stress fields in deep mines around the world. Improvements in stress measurements of Earth's crust is fundamental to several industries such as oil and gas, mining, nuclear waste management, and enhanced geothermal systems. Quantifying the state of stress and the geophysical properties of different rock types is a major complication in geophysical monitoring of deep mines. Most stress measurement techniques involve either the boreholes or their cores, however these measurements usually only give stress along one axis, not the complete stress tensor. The goal of this project is to investigate a new method of acquiring a complete stress tensor of the in situ stress in the Earth's crust. This project is part of a comprehensive, exploration geophysical study in a deep, highly stressed mine located in Sudbury, Ontario, Canada, and focuses on two boreholes located in this mine. These boreholes are approximately 400 m long with NQ diameters and are located at depths of about 1300 - 1600 m and 1700 - 2000 m. Two borehole logging surveys were performed on both boreholes, October 2013 and July 2015, in order to perform a time-lapse analysis of the geophysical changes in the mine. These multi-parameter surveys include caliper, full waveform sonic, televiewer, chargeability (IP), and resistivity. Laboratory experiments have been performed on borehole core samples of varying geologies from each borehole. These experiments have measured the geophysical properties including elastic modulus, bulk modulus, P- and S-wave velocities, and density. The apparatus' used for this project are geophysical imaging cells capable

Measurement and prediction of voice support and room gain

DEFF Research Database (Denmark)

Pelegrin Garcia, David; Brunskog, Jonas; Lyberg-Åhlander, Viveka

2012-01-01

and good acoustical quality lies in the range between 14 and 9 dB, whereas the room gain is in the range between 0.2 and 0.5 dB. The prediction model for voice support describes the measurements in the classrooms with a coefficient of determination of 0.84 and a standard deviation of 1.2 dB....

Experimental study on reactivity measurement in thermal reactor by polarity correlation method

International Nuclear Information System (INIS)

Yasuda, Hideshi

1977-11-01

Experimental study on the polarity correlation method for measuring the reactivity of a thermal reactor, especially the one possessing long prompt neutron lifetime such as graphite on heavy water moderated core, is reported. The techniques of reactor kinetics experiment are briefly reviewed, which are classified in two groups, one characterized by artificial disturbance to a reactor and the other by natural fluctuation inherent in a reactor. The fluctuation phenomena of neutron count rate are explained using F. de Hoffman's stochastic method, and correlation functions for the neutron count rate fluctuation are shown. The experimental results by polarity correlation method applied to the β/l measurements in both graphite-moderated SHE core and light water-moderated JMTRC and JRR-4 cores, and also to the measurement of SHE shut down reactivity margin are presented. The measured values were in good agreement with those by a pulsed neutron method in the reactivity range from critical to -12 dollars. The conditional polarity correlation experiments in SHE at -20 cent and -100 cent are demonstrated. The prompt neutron decay constants agreed with those obtained by the polarity correlation experiments. The results of experiments measuring large negative reactivity of -52 dollars of SHE by pulsed neutron, rod drop and source multiplication methods are given. Also it is concluded that the polarity and conditional polarity correlation methods are sufficiently applicable to noise analysis of a low power thermal reactor with long prompt neutron lifetime. (Nakai, Y.)

Strain measurements of nuclear power plant steam generator antiseismic supports

International Nuclear Information System (INIS)

Kulichevsky, R.

1997-01-01

The nuclear power plants steam generators have different types of structural supports. One of these types are the antiseismic supports, which are intended to be under stress only if a seismic event takes place. Nevertheless, the antiseismic supports lugs, that are welded to the steam generator vessel, are subjected to thermal fatigue because of the temperature cycles related with the shut down and start up operations performed during the life of the nuclear power plant. In order to evaluate the stresses that the lugs are subjected to, several strain gages were welded on two supports lugs, positioned at two heights of one of the Embalse nuclear power plant steam generators. In this paper, the instrumentation used and the strain measurements obtained during two start up operations are presented. The influence of the plant start up operation parameters on the lugs strain evolution is also analyzed. (author) [es

Modeling and experimental characterization of a new piezoelectric sensor for low-amplitude vibration measurement

International Nuclear Information System (INIS)

Hou, X Y; Koh, C G; Kuang, K S C; Lee, W H

2017-01-01

This paper investigates the capability of a novel piezoelectric sensor for low-frequency and low-amplitude vibration measurement. The proposed design effectively amplifies the input acceleration via two amplifying mechanisms and thus eliminates the use of the external charge amplifier or conditioning amplifier typically employed for measurement system. The sensor is also self-powered, i.e. no external power unit is required. Consequently, wiring and electrical insulation for on-site measurement are considerably simpler. In addition, the design also greatly reduces the interference from rotational motion which often accompanies the translational acceleration to be measured. An analytical model is developed based on a set of piezoelectric constitutive equations and beam theory. Closed-form expression is derived to correlate sensor geometry and material properties with its dynamic performance. Experimental calibration is then carried out to validate the analytical model. After calibration, experiments are carried out to check the feasibility of the new sensor in structural vibration detection. From experimental results, it is concluded that the proposed sensor is suitable for measuring low-frequency and low-amplitude vibrations. (paper)

Experimental analysis of a rigid rotor supported on aerodynamic foil journal bearings

Directory of Open Access Journals (Sweden)

Arghir M.

2014-01-01

Full Text Available Aerodynamic foil bearings are highly non linear components used or intending to be used for supporting high speed rotors (>30 krpm of low size rotating machines (<400 kW. The non linear character comes from the highly deformable structure of the bearing made of thin steel sheets and from the Coulomb friction forces arising during dynamic displacements. The present work shows the non linear response of a rigid rotor supported by a pair of such bearings and entrained at 82 krpm. The measurements performed during the coast down revealed sub synchronous and asynchronous vibrations of the rotor and their multiples. A simplified theoretical model reproduces qualitatively some of these non linear characteristics.

Telescience testbed: Operational support functions for biomedical experiments

Science.gov (United States)

Yamashita, Masamichi; Watanabe, Satoru; Shoji, Takatoshi; Clarke, Andrew H.; Suzuki, Hiroyuki; Yanagihara, Dai

A telescience testbed was conducted to study the methodology of space biomedicine with simulated constraints imposed on space experiments. An experimental subject selected for this testbedding was an elaborate surgery of animals and electrophysiological measurements conducted by an operator onboard. The standing potential in the ampulla of the pigeon's semicircular canal was measured during gravitational and caloric stimulation. A principal investigator, isolated from the operation site, participated in the experiment interactively by telecommunication links. Reliability analysis was applied to the whole layers of experimentation, including design of experimental objectives and operational procedures. Engineering and technological aspects of telescience are discussed in terms of reliability to assure quality of science. Feasibility of robotics was examined for supportive functions to reduce the workload of the onboard operator.

Experimental device for the X-ray energetic distribution measurement in a tokamak plasma

International Nuclear Information System (INIS)

Perez-Navarro, A.

1977-01-01

An experimental system to measure the X-ray spectrum in a tokamak plasma is described, emphasizing its characteristics: resolution, dead time and the pulse pile-up distortion effects on the X-ray spectra. (author) [es

Role of experimental resolution in measurements of critical layer thickness for strained-layer epitaxy

International Nuclear Information System (INIS)

Fritz, I.J.

1987-01-01

Experimental measurements of critical layer thicknesses (CLT's) in strained-layer epitaxy are considered. Finite experimental resolution can have a major effect on measured CLT's and can easily lead to spurious results. The theoretical approach to critical layer thicknesses of J. W. Matthews [J. Vac. Sci. Technol. 12, 126 (1975)] has been modified in a straightforward way to predict the apparent critical thickness for an experiment with finite resolution in lattice parameter. The theory has also been modified to account for the general empirical result that fewer misfit dislocations are generated than predicted by equilibrium calculation. The resulting expression is fit to recent x-ray diffraction data on InGaAs/GaAs and SiGe/Si. The results suggest that CLT's in these systems may not be significantly larger than predicted by equilibrium theory, in agreement with high-resolution measurements

Problems in the Latina paradox: measuring social support for pregnant immigrant women from Mexico.

Science.gov (United States)

Fleuriet, K Jill

2009-04-01

Women who have immigrated to the United States from Mexico have better than expected birth outcomes. Part of this apparent health 'paradox' has been explained by high levels of social support which are thought to offset known risk factors for low birth weight. Yet common measures of social support during pregnancy suffer from presumptions of cultural homogeneity and a-priori definitions of meaningful social support. Analysis of qualitative data from ethnographic research with 28 low-income immigrant women from Mexico living in south Texas demonstrates that preferences for certain kinds of social support vary considerably, based on how each woman makes meaning of being pregnant. This diversity is one more piece of evidence that minority cultures cannot be essentialised in health disparities research. By not measuring the diversity of desire for different kinds of support, existing correlations between social support and birth outcomes may obscure other important psychosocial mediators, such as pregnancy-related social status, that could impact birth outcomes. Moreover, a measure of pregnancy-related status may offer a more thorough explanation of the 'protective effect' that could be explored independent of immigrant status.

Experimental determination of an ionisation detector for measuring the nuclear lifetime

International Nuclear Information System (INIS)

Tisserant, S.

1982-06-01

The proton or neutron decay signature needs a good measurement of the varied produced particle energy, together with a good identification of them. The lack of experimental data on electron and charged pion of low energy led to experiment two series of tests. This thesis study precise, from these tests, the performances of the detector that will be installed at Modane. Prototype performances are first studied, concerning the particle energy measurement (electron and charged pions) and their identification. To extrapolate these results to the final detector, simulation programs will be used. The application of such a program that Electron-Gamma-Shower to energies below 500 MeV/c 2 for electromagnetic showers will be verified. For the pions, a simulation program of pion-nucleus interactions at low energy will be checked out from the experimental test data. Scattering effects, charge exchange and absorption are particularly concerned. These simulations reproduce the prototype results; they will be applied to the expected decay modes of proton and neutron. It will be shown that a fine grain detector. Shows a comparable sensitivty for every mode without final neutrino. Triggering probability and decay sign probability will be studied particularly [fr

Experimental results on the MOX fuel. Study of the calculus/measures divergences

International Nuclear Information System (INIS)

Martin, S.

1997-01-01

For each nuclear plant unit restart, all safety criterion have to be respected. Various parameters as boron concentration, temperature coefficient, worth or power and activity distributions related to fuel assemblies, have to be calculated. To compute these parameters Framatome uses the neutronic channel Science. Before the validation they are compare to experimental measures. For UO 2 fuel the divergence calculus/measures are correct. But for MOX fuels the divergence worsening. This paper discusses tis divergence and research the origin. (A.L.B.)

Experimental infrared measurements for hydrocarbon pollutant determination in subterranean waters

Science.gov (United States)

Lay-Ekuakille, A.; Palamara, I.; Caratelli, D.; Morabito, F. C.

2013-01-01

Subterranean waters are often polluted by industrial and anthropic effluents that are drained in subsoil. To prevent and control pollution, legislations of different developed countries require an online monitoring measurement, especially for detecting organic solvents (chlorinated and unchlorinated ones). Online measurements include both real-time and no real-time measurements. In general, it is difficult to implement real-time measurements in stricto sensu for online acquisitions on aqueous effluents since they need to be processed by a modeling. This research presents an experimental measurement system based on infrared (IR) spectroscopy for aqueous effluents containing hydrocarbons and capable of displaying excellent values of pollutant concentrations even in instable conditions; the system is able to detect pollutants either in laminar or turbulent flow. The results show the possibility of avoiding the use of "Pitot tube" that is employed to create a stagnation point in order to convert kinetic energy into potential one. This conversion allows the transformation of a turbulent flow in a laminar flow making easy measurement of pollutants included in an aqueous effluent. Obviously, "Pitot tube" is also used for other fluid effluents. The obtained results have been compared with those produced by means of sophisticated IR instrumentation for laboratory applications.

Crack identification method in beam-like structures using changes in experimentally measured frequencies and Particle Swarm Optimization

Science.gov (United States)

Khatir, Samir; Dekemele, Kevin; Loccufier, Mia; Khatir, Tawfiq; Abdel Wahab, Magd

2018-02-01

In this paper, a technique is presented for the detection and localization of an open crack in beam-like structures using experimentally measured natural frequencies and the Particle Swarm Optimization (PSO) method. The technique considers the variation in local flexibility near the crack. The natural frequencies of a cracked beam are determined experimentally and numerically using the Finite Element Method (FEM). The optimization algorithm is programmed in MATLAB. The algorithm is used to estimate the location and severity of a crack by minimizing the differences between measured and calculated frequencies. The method is verified using experimentally measured data on a cantilever steel beam. The Fourier transform is adopted to improve the frequency resolution. The results demonstrate the good accuracy of the proposed technique.

An innovative method for coordinate measuring machine one-dimensional self-calibration with simplified experimental process.

Science.gov (United States)

Fang, Cheng; Butler, David Lee

2013-05-01

In this paper, an innovative method for CMM (Coordinate Measuring Machine) self-calibration is proposed. In contrast to conventional CMM calibration that relies heavily on a high precision reference standard such as a laser interferometer, the proposed calibration method is based on a low-cost artefact which is fabricated with commercially available precision ball bearings. By optimizing the mathematical model and rearranging the data sampling positions, the experimental process and data analysis can be simplified. In mathematical expression, the samples can be minimized by eliminating the redundant equations among those configured by the experimental data array. The section lengths of the artefact are measured at arranged positions, with which an equation set can be configured to determine the measurement errors at the corresponding positions. With the proposed method, the equation set is short of one equation, which can be supplemented by either measuring the total length of the artefact with a higher-precision CMM or calibrating the single point error at the extreme position with a laser interferometer. In this paper, the latter is selected. With spline interpolation, the error compensation curve can be determined. To verify the proposed method, a simple calibration system was set up on a commercial CMM. Experimental results showed that with the error compensation curve uncertainty of the measurement can be reduced to 50%.

Flow-based vulnerability measures for network component importance: Experimentation with preparedness planning

International Nuclear Information System (INIS)

Nicholson, Charles D.; Barker, Kash; Ramirez-Marquez, Jose E.

2016-01-01

This work develops and compares several flow-based vulnerability measures to prioritize important network edges for the implementation of preparedness options. These network vulnerability measures quantify different characteristics and perspectives on enabling maximum flow, creating bottlenecks, and partitioning into cutsets, among others. The efficacy of these vulnerability measures to motivate preparedness options against experimental geographically located disruption simulations is measured. Results suggest that a weighted flow capacity rate, which accounts for both (i) the contribution of an edge to maximum network flow and (ii) the extent to which the edge is a bottleneck in the network, shows most promise across four instances of varying network sizes and densities. - Highlights: • We develop new flow-based measures of network vulnerability. • We apply these measures to determine the importance of edges after disruptions. • Networks of varying size and density are explored.

Experimental thermodynamics experimental thermodynamics of non-reacting fluids

CERN Document Server

Neindre, B Le

2013-01-01

Experimental Thermodynamics, Volume II: Experimental Thermodynamics of Non-reacting Fluids focuses on experimental methods and procedures in the study of thermophysical properties of fluids. The selection first offers information on methods used in measuring thermodynamic properties and tests, including physical quantities and symbols for physical quantities, thermodynamic definitions, and definition of activities and related quantities. The text also describes reference materials for thermometric fixed points, temperature measurement under pressures, and pressure measurements. The publicatio

In vivo measurement of aerodynamic weight support in freely flying birds

Science.gov (United States)

Lentink, David; Haselsteiner, Andreas; Ingersoll, Rivers

2014-11-01

Birds dynamically change the shape of their wing during the stroke to support their body weight aerodynamically. The wing is partially folded during the upstroke, which suggests that the upstroke of birds might not actively contribute to aerodynamic force production. This hypothesis is supported by the significant mass difference between the large pectoralis muscle that powers the down-stroke and the much smaller supracoracoideus that drives the upstroke. Previous works used indirect or incomplete techniques to measure the total force generated by bird wings ranging from muscle force, airflow, wing surface pressure, to detailed kinematics measurements coupled with bird mass-distribution models to derive net force through second derivatives. We have validated a new method that measures aerodynamic force in vivo time-resolved directly in freely flying birds which can resolve this question. The validation of the method, using independent force measurements on a quadcopter with pulsating thrust, show the aerodynamic force and impulse are measured within 2% accuracy and time-resolved. We demonstrate results for quad-copters and birds of similar weight and size. The method is scalable and can be applied to both engineered and natural flyers across taxa. The first author invented the method, the second and third authors validated the method and present results for quadcopters and birds.

Computer-supported resolution of measurement conflicts: a case-study in materials science

NARCIS (Netherlands)

de Jong, Hidde; Mars, Nicolaas; van der Vet, P.E.

1999-01-01

Resolving conflicts between different measurements ofa property of a physical system may be a key step in a discovery process. With the emergence of large-scale databases and knowledge bases with property measurements, computer support for the task of conflict resolution has become highly desirable.

Reversing a Negative Measurement in Process with Negative Events: A Haunted Negative Measurement and the Bifurcation of Time

CERN Document Server

Snyder, D M

2003-01-01

Reversing an ordinary measurement in process (a haunted measurement) is noted and the steps involved in reversing a negative measurement in process (a haunted negative measurement) are described. In order to discuss in a thorough manner reversing an ordinary measurement in process, one has to account for how reversing a negative measurement in process would work for the same experimental setup. The reason it is necessary to know how a negative measurement in process is reversed is because for a given experimental setup there is no physical distinction between reversing a negative measurement in process and reversing an ordinary measurement in process. In the absence of the reversal of a negative measurement in process in the same experimental setup that supports the reversal of an ordinary measurement in process, the possibility exists of which-way information concerning the negative measurement that would render theoretically implausible reversing an ordinary measuremnt in process. The steps in reversing a n...

An Experimental Comparison of Similarity Assessment Measures for 3D Models on Constrained Surface Deformation

Science.gov (United States)

Quan, Lulin; Yang, Zhixin

2010-05-01

To address the issues in the area of design customization, this paper expressed the specification and application of the constrained surface deformation, and reported the experimental performance comparison of three prevail effective similarity assessment algorithms on constrained surface deformation domain. Constrained surface deformation becomes a promising method that supports for various downstream applications of customized design. Similarity assessment is regarded as the key technology for inspecting the success of new design via measuring the difference level between the deformed new design and the initial sample model, and indicating whether the difference level is within the limitation. According to our theoretical analysis and pre-experiments, three similarity assessment algorithms are suitable for this domain, including shape histogram based method, skeleton based method, and U system moment based method. We analyze their basic functions and implementation methodologies in detail, and do a series of experiments on various situations to test their accuracy and efficiency using precision-recall diagram. Shoe model is chosen as an industrial example for the experiments. It shows that shape histogram based method gained an optimal performance in comparison. Based on the result, we proposed a novel approach that integrating surface constrains and shape histogram description with adaptive weighting method, which emphasize the role of constrains during the assessment. The limited initial experimental result demonstrated that our algorithm outperforms other three algorithms. A clear direction for future development is also drawn at the end of the paper.

An experimental set-up to measure Light Yield of Scintillating Fibres

CERN Document Server

Alfieri, C; Joram, C; Kenzie, M W

2015-01-01

In the context of the LHCb SciFi Tracker project, an experimental set up was designed and built to provide reliable and reproducible measurements of the light yield of scintillating fibres. This document describes the principle and technical realisation of the set-up. A few examples illustrate the operation and data analysis. In the first implementation of the set-up a photomultiplier tube with bialkali photocathode was used for the reading of the light from the fibres under test. In order to measure also green emitting fibres, the photomultiplier was replaced in January 2016 by a SiPM with higher sensitivity and larger spectral coverage1.

Measurements of experimental precision for trials with cowpea (Vigna unguiculata L. Walp.) genotypes.

Science.gov (United States)

Teodoro, P E; Torres, F E; Santos, A D; Corrêa, A M; Nascimento, M; Barroso, L M A; Ceccon, G

2016-05-09

The aim of this study was to evaluate the suitability of statistics as experimental precision degree measures for trials with cowpea (Vigna unguiculata L. Walp.) genotypes. Cowpea genotype yields were evaluated in 29 trials conducted in Brazil between 2005 and 2012. The genotypes were evaluated with a randomized block design with four replications. Ten statistics that were estimated for each trial were compared using descriptive statistics, Pearson correlations, and path analysis. According to the class limits established, selective accuracy and F-test values for genotype, heritability, and the coefficient of determination adequately estimated the degree of experimental precision. Using these statistics, 86.21% of the trials had adequate experimental precision. Selective accuracy and the F-test values for genotype, heritability, and the coefficient of determination were directly related to each other, and were more suitable than the coefficient of variation and the least significant difference (by the Tukey test) to evaluate experimental precision in trials with cowpea genotypes.

Further optimization studies of experimental dynamic responses measured on the HTGC Dragon reactor

International Nuclear Information System (INIS)

Cummins, J.D.

1968-04-01

This report considers some measurements made of the dynamics of the HTGC Dragon reactor and the optimization of a mathematical model which represents the reactor, by altering the parameters until a least squares fit between the experimental responses and the mathematical model is obtained. The experimental information was processed in various ways. The experimental response to an impulse, step or periodic sine wave change in reactivity was processed as an impulse, step or periodic sine wave response respectively and compared with a similar response from the model. In other studies the result of a binary cross correlation experiment (effectively an impulse response input) was processed as a frequency response and this experimental frequency response was compared with the frequency response from the mathematical model. It was possible therefore to compare the optimum values of parameters, obtained for different forms of perturbing signal and for different methods of processing and to relate the optima obtained to the problem of parameter estimation. (author)

Technique of measuring and evaluating the R3E dia. 112 experimental fuel element

International Nuclear Information System (INIS)

Stanc, S.; Badiar, S.

1974-10-01

The charging is considered of the R3E experimental fuel element having a diameter of 112 mm which will serve the simultaneous temperature measurement on 15 sites and neutron flux measurement on 7 sites aimed at verifying the improved R3-type fuel element with extended cladding and a new toroidal spacing. The temperature will be measured using jacket thermocouples while neutron flux will be measured by self-powered detectors. The methods are described of checking the measuring chain by determining the loop resistance of the thermocouples and SPN detectors in order to verify the correctness of the measured data. (J.B.)

Informatics to support the IOM social and behavioral domains and measures.

Science.gov (United States)

Hripcsak, George; Forrest, Christopher B; Brennan, Patricia Flatley; Stead, William W

2015-07-01

Consistent collection and use of social and behavioral determinants of health can improve clinical care, prevention and general health, patient satisfaction, research, and public health. A recent Institute of Medicine committee defined a panel of 11 domains and 12 measures to be included in electronic health records. Incorporating the panel into practice creates a number of informatics research opportunities as well as challenges. The informatics issues revolve around standardization, efficient collection and review, decision support, and support for research. The informatics community can aid the effort by simultaneously optimizing the collection of the selected measures while also partnering with social science researchers to develop and validate new sources of information about social and behavioral determinants of health. © The Author 2015. Published by Oxford University Press on behalf of the American Medical Informatics Association.

Development and evaluation of the INSPIRE measure of staff support for personal recovery.

Science.gov (United States)

Williams, Julie; Leamy, Mary; Bird, Victoria; Le Boutillier, Clair; Norton, Sam; Pesola, Francesca; Slade, Mike

2015-05-01

No individualised standardised measure of staff support for mental health recovery exists. To develop and evaluate a measure of staff support for recovery. initial draft of measure based on systematic review of recovery processes; consultation (n = 61); and piloting (n = 20). Psychometric evaluation: three rounds of data collection from mental health service users (n = 92). INSPIRE has two sub-scales. The 20-item Support sub-scale has convergent validity (0.60) and adequate sensitivity to change. Exploratory factor analysis (variance 71.4-85.1 %, Kaiser-Meyer-Olkin 0.65-0.78) and internal consistency (range 0.82-0.85) indicate each recovery domain is adequately assessed. The 7-item Relationship sub-scale has convergent validity 0.69, test-retest reliability 0.75, internal consistency 0.89, a one-factor solution (variance 70.5 %, KMO 0.84) and adequate sensitivity to change. A 5-item Brief INSPIRE was also evaluated. INSPIRE and Brief INSPIRE demonstrate adequate psychometric properties, and can be recommended for research and clinical use.

Theory of local and global processes which affect solar wind electrons. 2. Experimental support

International Nuclear Information System (INIS)

Scudder, J.D.; Olbert, S.

1979-01-01

We have extended the theoretical considerations of Scudder and Olbert (1979) (hereafter called paper 1) to show from the microscopic characteristics of the Coulomb cross section that there are three natural subpopulations for plasma electrons: the subthermals with local kinetic energy E 7kT/sub c/. We present experimental support from three experimental groups on three different spacecraft over a radial range in the interplanetary medium for the five interrelations projected in paper 1 between solar wind electron properties and changes in the interplanetary medium: (1) subthermals respond primarily to local changes (compressions and rarefactions) in stream dynamics: (2) the extrathermal fraction of the ambient electron density should be anticorrelated with the asymptotic bulk speed; (3) the extrathermal 'temperature' should be anticorrelated with the local wind speed at 1 AU; (4) the heat flux carried by electrons should be anticorrelated with the local bulk speed; and (5) the extrathermal differential 'temperature' should be nearly independent of radius within 1 Au. From first principles and the spatial inhomogeneity of the plasma we show that the velocity dependence of Coulomb collisions in the solar wind plasmaproduces a bifurcation in the solar wind electron distribution function at a transition energy E*. This energy is theoretically shown to scale with the local thermal temperature as E*(r) approx. =GAMMAkT/sub c/(r). This scaling is observationally supported over the radial range from 0.45 to 0.9 AU and at 1 AU. The extrathermals, defined on the basis of Coulomb collisions, are synonymous with the subpopulation previously labeled in the literature as the 'halo' or 'hot' component

EXPERIMENTAL MEASUREMENT, ANALYSIS AND MODELLING ...

African Journals Online (AJOL)

30 juin 2010 ... We obtain a good agreement between the resolution of the nonlinear equation of heat and the results obtained by the experimentation. . Keywords: Emissivity, Température, optimal Linearisation, finite elements. 1. ..... basse température, Rapport de Stage de D.E.A, Université Paris 12 – Val de Marne.

The teacher benefits from giving autonomy support during physical education instruction.

Science.gov (United States)

Cheon, Sung Hyeon; Reeve, Johnmarshall; Yu, Tae Ho; Jang, Hue Ryen

2014-08-01

Recognizing that students benefit when they receive autonomy-supportive teaching, the current study tested the parallel hypothesis that teachers themselves would benefit from giving autonomy support. Twenty-seven elementary, middle, and high school physical education teachers (20 males, 7 females) were randomly assigned either to participate in an autonomy-supportive intervention program (experimental group) or to teach their physical education course with their existing style (control group) within a three-wave longitudinal research design. Manipulation checks showed that the intervention was successful, as students perceived and raters scored teachers in the experimental group as displaying a more autonomy-supportive and less controlling motivating style. In the main analyses, ANCOVA-based repeated-measures analyses showed large and consistent benefits for teachers in the experimental group, including greater teaching motivation (psychological need satisfaction, autonomous motivation, and intrinsic goals), teaching skill (teaching efficacy), and teaching well-being (vitality, job satisfaction, and lesser emotional and physical exhaustion). These findings show that giving autonomy support benefits teachers in much the same way that receiving it benefits their students.

Development, content validity, and piloting of an instrument designed to measure managers' attitude toward workplace breastfeeding support.

Science.gov (United States)

Chow, Tan; Wolfe, Edward W; Olson, Beth H

2012-07-01

Manager attitude is influential in female employees' perceptions of workplace breastfeeding support. Currently, no instrument is available to assess manager attitude toward supporting women who wish to combine breastfeeding with work. We developed and piloted an instrument to measure manager attitudes toward workplace breastfeeding support entitled the "Managers' Attitude Toward Breastfeeding Support Questionnaire," an instrument that measures four constructs using 60 items that are rated agree/disagree on a 4-point Likert rating scale. We established the content validity of the Managers' Attitude Toward Breastfeeding Support Questionnaire measures through expert content review (n=22), expert assessment of item fit (n=11), and cognitive interviews (n=8). Data were collected from a purposive sample of 185 front-line managers who had experience supervising female employees, and responses were scaled using the Multidimensional Random Coefficients Multinomial Logit Model. Dimensionality analyses supported the proposed four-construct model. Reliability ranged from 0.75 to 0.86, and correlations between the constructs were moderately strong (0.47 to 0.71). Four items in two constructs exhibited model-to-data misfit and/or a low score-measure correlation. One item was revised and the other three items were retained in the Managers' Attitude Toward Breastfeeding Support Questionnaire. Findings of this study suggest that the Managers' Attitude Toward Breastfeeding Support Questionnaire measures are reliable and valid indicators of manager attitude toward workplace breastfeeding support, and future research should be conducted to establish external validity. The Managers' Attitude Toward Breastfeeding Support Questionnaire could be used to collect data in a standardized manner within and across companies to measure and compare manager attitudes toward supporting breastfeeding. Organizations can subsequently develop targeted strategies to improve support for breastfeeding

Experimental evaluation of permanent magnet probe flowmeter measuring high temperature liquid sodium flow in the ITSL

Energy Technology Data Exchange (ETDEWEB)

Jeong, Uiju; Kim, Yun Ho [Nuclear engineering Department, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Kim, Jong-Man; Kim, Tae-Joon [Korea Atomic Energy Research Institute, 1045 Daedeok-daero, Yuseong-gu, Daejeon 305-353 (Korea, Republic of); Kim, Sung Joong, E-mail: sungjkim@mit.edu [Nuclear engineering Department, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of)

2013-12-15

Highlights: • An Instrument Test Sodium Loop (ITSL) has been built and tested in various conditions at KAERI. • Free fall of liquid sodium was conducted experimentally and numerically. • A Permanent Magnet Probe Flowmeter (PMPF) was experimented in the ITSL. • Excellent linearity of the PMPF was achieved under high temperature condition. - Abstract: The Instrument Test Sodium Loop (ITSL) installed at Korea Atomic Energy Research Institute (KAERI) is a medium-size experimental facility dedicated to obtaining relevant experimental data of liquid sodium flow characteristics under various thermal hydraulic conditions and sodium purification. The ITSL has been utilized to perform thermal flow measurement of the liquid sodium and to calibrate a Permanent Magnet Probe Flowmeter (PMPF). The primary objective of this study is to obtain liquid sodium flow rate given a wide temperature range using the PMPF. Non-stationary method was adopted for the calibration of the probe given the liquid sodium temperature range of 150–415 °C. A relationship between the measured voltage signal and flow rate was obtained successfully. It is observed that the calibration experiments result in excellent linear relationships between measured voltage and volumetric flow rate at various temperature conditions. Also a computational analysis using FlowMaster, is employed to facilitate the calibration process by predicting the liquid sodium flow rate. Finally the effect of the fluid temperature on thermal flow measurements is discussed in light of the obtained experimental data.

Experimental research on crossing shock wave boundary layer interactions

Science.gov (United States)

Settles, G. S.; Garrison, T. J.

1994-10-01

An experimental research effort of the Penn State Gas Dynamics Laboratory on the subject of crossing shock wave boundary layer interactions is reported. This three year study was supported by AFOSR Grant 89-0315. A variety of experimental techniques were employed to study the above phenomena including planar laser scattering flowfield visualization, kerosene lampblack surface flow visualization, laser-interferometer skin friction surveys, wall static pressure measurements, and flowfield five-hole probe surveys. For a model configuration producing two intersecting shock waves, measurements were made for a range of oblique shock strengths at freestream Mach numbers of 3.0 and 3.85. Additionally, measurements were made at Mach 3.85 for a configuration producing three intersecting waves. The combined experimental dataset was used to formulate the first detailed flowfield models of the crossing-shock and triple-shock wave/boundary layer interactions. The structure of these interactions was found to be similar over a broad range of interaction strengths and is dominated by a large, separated, viscous flow region.

Measurement Development and Validation of the Family Supportive Supervisor Behavior Short-Form (FSSB-SF)

Science.gov (United States)

Hammer, Leslie B.; Kossek, Ellen Ernst; Bodner, Todd; Crain, Tori

2013-01-01

Recently, scholars have demonstrated the importance of Family Supportive Supervisor Behaviors (FSSB), defined as behaviors exhibited by supervisors that are supportive of employees’ family roles, in relation to health, well-being, and organizational outcomes. FSSB was originally conceptualized as a multidimensional, superordinate construct with four subordinate dimensions assessed with 14 items: emotional support, instrumental support, role modeling behaviors, and creative work-family management. Retaining one item from each dimension, two studies were conducted to support the development and use of a new FSSB-Short Form (FSSB-SF). Study 1 draws on the original data from the FSSB validation study of retail employees to determine if the results using the 14-item measure replicate with the shorter 4-item measure. Using data from a sample of 823 information technology professionals and their 219 supervisors, Study 2 extends the validation of the FSSB-SF to a new sample of professional workers and new outcome variables. Results from multilevel confirmatory factor analyses and multilevel regression analyses provide evidence of construct and criterion-related validity of the FSSB-SF, as it was significantly related to work-family conflict, job satisfaction, turnover intentions, control over work hours, obligation to work when sick, perceived stress, and reports of family time adequacy. We argue that it is important to develop parsimonious measures of work-family specific support to ensure supervisor support for work and family is mainstreamed into organizational research and practice. PMID:23730803

Supporting Applications Development and Operation Using IT Security and Audit Measures

Directory of Open Access Journals (Sweden)

Katalin Szenes

2012-01-01

Full Text Available The market success of the enterprises depends on the ability to support their business processes. This involves the requirement of a seamless, well-ordered operation of the whole company. Operation is greatly affected by the quality of its IT support. The information should be available, handled confidentially, preserving its integrity, have to be processed in a reliable, efficient, effective way, in compliance with the requirements of supervisory authorities. Extending the scope of these information criteria to criteria determining operations quality and adding two business-level requirements to them makes possible to find preventive, detective andcorrective, originally information security control measures, raised to the level of operational quality, that support the market success of the institutions.

A complete dosimetry experimental program in support to the core characterization and to the power calibration of the CABRI reactor. A complete dosimetry experimental program in support of the core characterization and of the power calibration of the CABRI reactor

Energy Technology Data Exchange (ETDEWEB)

Rodiac, F.; Hudelot, JP.; Lecerf, J.; Garnier, Y.; Ritter, G. [CEA, DEN, CAD/DER/SRES/LPRE, Cadarache, F-13108 Saint-Paul-lez-Durance, (France); Gueton, O.; Colombier, AC. [CEA, DEN, CAD/DER/SPRC/LPN, Cadarache, F-13108 Saint-Paul-lez-Durance, (France); Domergue, C. [CEA, DEN, CAD/DER/SPEx/LDCI, Cadarache, F-13108 Saint-Paul-lez-Durance, (France)

2015-07-01

CABRI is an experimental pulse reactor operated by CEA at the Cadarache research center. Since 1978 the experimental programs have aimed at studying the fuel behavior under Reactivity Initiated Accident (RIA) conditions. Since 2003, it has been refurbished in order to be able to provide RIA and LOCA (Loss Of Coolant Accident) experiments in prototypical PWR conditions (155 bar, 300 deg. C). This project is part of a broader scope including an overall facility refurbishment and a safety review. The global modification is conducted by the CEA project team. It is funded by IRSN, which is conducting the CIP experimental program, in the framework of the OECD/NEA project CIP. It is financed in the framework of an international collaboration. During the reactor restart, commissioning tests are realized for all equipment, systems and circuits of the reactor. In particular neutronics and power commissioning tests will be performed respectively in 2015 and 2016. This paper focuses on the design of a complete and original dosimetry program that was built in support to the CABRI core characterization and to the power calibration. Each one of the above experimental goals will be fully described, as well as the target uncertainties and the forecasted experimental techniques and data treatment. (authors)

Measuring and monitoring energy access: Decision-support tools for policymakers in Africa

International Nuclear Information System (INIS)

Hailu, Yohannes G.

2012-01-01

A significant number of African States have adapted energy access targets. In evaluating progress towards these goals, measuring and monitoring energy access becomes relevant. This paper reviews energy access indicators and identifies their utility and challenges in their application. By focusing on Africa, a broader framework for energy access measurement and monitoring is discussed, along with implementation barriers and potential solutions. To demonstrate the utility of energy access decision-support tool in Africa, a scenario analysis in five regional energy pools is conducted using the Energy Spending Model tool. Institutionalizing monitoring and decision-support tools can provide valuable feedback to policymakers aiming to design and implement effective energy access programs serving a growing population in Africa. - Highlights: ► Most African countries have adapted energy access targets. ► To monitor and evaluate performance, monitoring and decision-support tools are required. ► Framework for tool development should consider data, cost, political and other factors. ► Implementation constraints include technical, data, resource and urban/rural issues. ► Electricity Spending Needs model is one decision support tool that ties access targets to investment needs. ► Monitoring tools provide crucial feedback on Africa's energy access progress.

The Recommendations for Linear Measurement Techniques on the Measurements of Nonlinear System Parameters of a Joint.

Energy Technology Data Exchange (ETDEWEB)

Smith, Scott A [Univ. of Maryland Baltimore County (UMBC), Baltimore, MD (United States); Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Catalfamo, Simone [Univ. of Stuttgart (Germany); Brake, Matthew R. W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rice Univ., Houston, TX (United States); Schwingshackl, Christoph W. [Imperial College, London (United Kingdom); Reusb, Pascal [Daimler AG, Stuttgart (Germany)

2017-01-01

In the study of the dynamics of nonlinear systems, experimental measurements often convolute the response of the nonlinearity of interest and the effects of the experimental setup. To reduce the influence of the experimental setup on the deduction of the parameters of the nonlinearity, the response of a mechanical joint is investigated under various experimental setups. These experiments first focus on quantifying how support structures and measurement techniques affect the natural frequency and damping of a linear system. The results indicate that support structures created from bungees have negligible influence on the system in terms of frequency and damping ratio variations. The study then focuses on the effects of the excitation technique on the response for a linear system. The findings suggest that thinner stingers should not be used, because under the high force requirements the stinger bending modes are excited adding unwanted torsional coupling. The optimal configuration for testing the linear system is then applied to a nonlinear system in order to assess the robustness of the test configuration. Finally, recommendations are made for conducting experiments on nonlinear systems using conventional/linear testing techniques.

Reducing measurement uncertainty drives the use of multiple technologies for supporting metrology

Science.gov (United States)

Banke, Bill, Jr.; Archie, Charles N.; Sendelbach, Matthew; Robert, Jim; Slinkman, James A.; Kaszuba, Phil; Kontra, Rick; DeVries, Mick; Solecky, Eric P.

2004-05-01

Perhaps never before in semiconductor microlithography has there been such an interest in the accuracy of measurement. This interest places new demands on our in-line metrology systems as well as the supporting metrology for verification. This also puts a burden on the users and suppliers of new measurement tools, which both challenge and complement existing manufacturing metrology. The metrology community needs to respond to these challenges by using new methods to assess the fab metrologies. An important part of this assessment process is the ability to obtain accepted reference measurements as a way of determining the accuracy and Total Measurement Uncertainty (TMU) of an in-line critical dimension (CD). In this paper, CD can mean any critical dimension including, for example, such measures as feature height or sidewall angle. This paper describes the trade-offs of in-line metrology systems as well as the limitations of Reference Measurement Systems (RMS). Many factors influence each application such as feature shape, material properties, proximity, sampling, and critical dimension. These factors, along with the metrology probe size, interaction volume, and probe type such as e-beam, optical beam, and mechanical probe, are considered. As the size of features shrinks below 100nm some of the stalwarts of reference metrology come into question, such as the electrically determined transistor gate length. The concept of the RMS is expanded to show how multiple metrologies are needed to achieve the right balance of accuracy and sampling. This is also demonstrated for manufacturing metrology. Various comparisons of CDSEM, scatterometry, AFM, cross section SEM, electrically determined CDs, and TEM are shown. An example is given which demonstrates the importance in obtaining TMU by balancing accuracy and precision for selecting manufacturing measurement strategy and optimizing manufacturing metrology. It is also demonstrated how the necessary supporting metrology will

Feasibility study of thermal insulation materials for core support of experimental VHTR

International Nuclear Information System (INIS)

Kawakami, H.; Nakanishi, T.

1982-01-01

Thermal insulation materials for core support of the experimental VHTR, planned by JAERI, should maintain moderate compressive strength and dimensional stability as well as low thermal conductivity at the maximum service temperature of 1100 0 C for 20 years. For selecting materials, we investigate properties of some candidates, and evaluate their feasibility. Preliminary tests, heat treatment test and compressive creep tests for 1000 hours at 900 0 C and 1000 0 C were conducted. In the preliminary tests, EG-38B (carbon baked at 1350 0 C) and Fine Finnex 600 (silicon nitride) showed acceptable physical stability. In the heat treatment tests, silicon nitride showed weight loss probably caused by thermal decomposition. Compressive creep deformation of Fine Finnex 600 was negligible under stress of 100 kg/cm 2 for 1000 hours. Heat treatment at 1200 to 1300 0 C for 50 hours improved dimensional stability of carbon at 1000 0 C

Deriving Structural Information from Experimentally Measured Data on Biomolecules.

Science.gov (United States)

van Gunsteren, Wilfred F; Allison, Jane R; Daura, Xavier; Dolenc, Jožica; Hansen, Niels; Mark, Alan E; Oostenbrink, Chris; Rusu, Victor H; Smith, Lorna J

2016-12-23

During the past half century, the number and accuracy of experimental techniques that can deliver values of observables for biomolecular systems have been steadily increasing. The conversion of a measured value Q exp of an observable quantity Q into structural information is, however, a task beset with theoretical and practical problems: 1) insufficient or inaccurate values of Q exp , 2) inaccuracies in the function Q(r→) used to relate the quantity Q to structure r→ , 3) how to account for the averaging inherent in the measurement of Q exp , 4) how to handle the possible multiple-valuedness of the inverse r→(Q) of the function Q(r→) , to mention a few. These apply to a variety of observable quantities Q and measurement techniques such as X-ray and neutron diffraction, small-angle and wide-angle X-ray scattering, free-electron laser imaging, cryo-electron microscopy, nuclear magnetic resonance, electron paramagnetic resonance, infrared and Raman spectroscopy, circular dichroism, Förster resonance energy transfer, atomic force microscopy and ion-mobility mass spectrometry. The process of deriving structural information from measured data is reviewed with an eye to non-experts and newcomers in the field using examples from the literature of the effect of the various choices and approximations involved in the process. A list of choices to be avoided is provided. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

MSDD: a manually curated database of experimentally supported associations among miRNAs, SNPs and human diseases

OpenAIRE

Yue, Ming; Zhou, Dianshuang; Zhi, Hui; Wang, Peng; Zhang, Yan; Gao, Yue; Guo, Maoni; Li, Xin; Wang, Yanxia; Zhang, Yunpeng; Ning, Shangwei; Li, Xia

2017-01-01

Abstract The MiRNA SNP Disease Database (MSDD, http://www.bio-bigdata.com/msdd/) is a manually curated database that provides comprehensive experimentally supported associations among microRNAs (miRNAs), single nucleotide polymorphisms (SNPs) and human diseases. SNPs in miRNA-related functional regions such as mature miRNAs, promoter regions, pri-miRNAs, pre-miRNAs and target gene 3′-UTRs, collectively called ‘miRSNPs’, represent a novel category of functional molecules. miRSNPs can lead to m...

An Experimental Study on the Effectiveness of Disclosing Stressful Life Events and Support Messages: When Cognitive Reappraisal Support Decreases Emotional Distress, and Emotional Support Is Like Saying Nothing at All

Science.gov (United States)

Batenburg, Anika; Das, Enny

2014-01-01

How can we best support others in difficult times? Studies testing the effects of supportive communication revealed mixed findings. The current study focuses on the effects of supportive communication following different disclosure styles, and includes outcome measures to assess emotional well-being. Hypotheses were tested in a 2 (disclosure style: cognitive reappraisal disclosure vs. emotional disclosure) ×3 (support message: cognitive reappraisal response vs. socio-affective response vs. no response) between subjects factorial design. Receiving a cognitive reappraisal response, rather than a socio-affective response or no response, decreased emotional distress in the emotional disclosure group. Support messages showed no effects in the cognitive reappraisal disclosure group. Although socio-affective responses were positively evaluated, cognitive reappraisal responses may be more effective during emotional upheaval because they provide a positive way out of negative emotions. PMID:25531509

Investigation on welding and cutting methods for blanket support legs of fusion experimental reactors

International Nuclear Information System (INIS)

Tokami, Ikuhide; Nakahira, Masataka; Kurasawa, Toshimasa; Sato, Satoshi; Furuya, Kazuyuki; Hatano, Toshihisa; Takatsu, Hideyuki; Kuroda, Toshimasa.

1996-07-01

A toroidally-and poloidally-divided modular blanket has been proposed for a fusion experimental reactor, such as ITER, to enhance its maintainability as well as improve its fabricability. The blanket module, typically the size of 1 m wide, 1-2 m high and 0.4 m deep and the weight of 4 ton, will be supported by support legs which are extruded from back of the module and connected to a 70-100 mm thick strong back plate. The support leg has to withstand large electromagnetic force during plasma disruption and provide the way for in-situ module replacement by remote handling. For the connection method of the support leg to the back plate, a welding approach has been investigated here in terms of its high reliability against the large electromagnetic loads. For the welding approach, the support leg needs to be 70 mm thick, and the working space for welding/cutting heads are limited to 100 mm x 150 mm adjacent to the support leg. Based on a comparison of several welding methods, e.g. NGTIG, NGMIG and laser, NGTIG has been selected as a reference due to its well-established technology and the least R and D required. As for the cutting method, a plasma cutting has been given the highest priority to be pursued because of its compactness and high speed. Through preliminary design studies, the possibility of small welding/cutting heads that will work in the limited space has been shown, and maintenance route for in-situ module replacement with pre-and postfixture of the module has been investigated. Also preliminary R and Ds have resulted in; 1)the welding distortion is predictable according to the shape of weld groove and adjustable to meet the placement requirement of the module first wall, 2)the plasma cut surface can be rewelded without machining, 3)the welding/cutting time will meet the requirement of maintenance time. (author)

Measures of Patient Activation and Social Support in a Peer-Led Support Network for Women With Cardiovascular Disease.

Science.gov (United States)

Witt, Dawn; Benson, Gretchen; Campbell, Susan; Sillah, Arthur; Berra, Kathy

Social support has been associated with beneficial effects on many disease states and overall health and well-being. However, there is limited research exploring the impact of peer-led support models among women living with coronary heart disease. This study describes the structure of peer-led support groups offered by WomenHeart (WH): The National Coalition for Women Living with Heart Disease, and assesses WH participants' quality of life and social, emotional, and physical health. Participants were recruited from 50 WH groups. A 70-item online survey was administered, and the main analytic sample included 157 women. Multivariate logistic regression was used to examine the association between patient activation levels (lower activation levels: 1, 2 vs higher activation levels: 3, 4) and social support scores (range: lowest 8 to highest 34), adjusting for age. High levels of social support, patient activation, physical activity, and low levels of stress, anxiety, and depression were reported. Those who were at or above the median for the social support measures (indicating high levels of social support) had greater odds of high levels of patient activation (level 3 or 4) than individuals reporting low levels of social support (OR = 2.23; 95% CI, 1.04-4.76; P = .012). Women who regularly attended a support group by a trained peer leader were highly engaged in their health care and had low levels of stress, anxiety, and depression. These findings lend credibility to the value of the peer support model and could potentially be replicated in other disease states to enhance patient care.

Experimental subcritical reactivity determinations employing APSD measurements with pulse mode detectors in the IPEN/MB-01 reactor

International Nuclear Information System (INIS)

Santos, Adimir dos; Lee, Seung Min; Diniz, Ricardo; Jerez, Rogerio

2011-01-01

This work aims to determine experimentally the subcritical reactivity levels of several configurations of the IPEN/MB-01 reactor in an approach based on the subcritical kinetic model developed by Gandini and Salvatores. The procedure employs the measurements of the APSD (Auto Power Spectral Density) using pulse mode detectors. The proposed approach is based only on measured quantities such as counting rates and the parameters arising from the least square approach of the APSD. Other difficult quantity such as detector efficiencies is not needed in the method. Several measurements of APSD were performed in varying degrees of sub-criticality (up to around -7000 pcm). The APSD data were least-square fitted to get the prompt decay mode (α). Beside the startup source, an external neutron sources of Am-Be was installed near the core in order to improve neutron count statistics. The final experimental results are of very good quality. The experiment shows clearly that the classical one point kinetic theory cannot describe the measured reactivity. MCNP K eff results were compared to the corresponding experimental results. The agreement was fairly good. (author)

Experimental Longitudinal Test of the Influence of Autonomy-Supportive Teaching on Motivation for Participation in Elementary School Physical Education

Science.gov (United States)

Leptokaridou, Elisavet T.; Vlachopoulos, Symeon P.; Papaioannou, Athanasios G.

2016-01-01

The present study examined the efficacy of autonomy-supportive teaching during elementary school physical education (PE) in influencing pupils' enjoyment, fear of failure, boredom and effort. A sample of 54 pupils attending fifth and sixth grades comprised the control group (typical instruction; n = 27) and the experimental group…

Validation of High-Fidelity Reactor Physics Models for Support of the KJRR Experimental Campaign in the Advanced Test Reactor

Energy Technology Data Exchange (ETDEWEB)

Nigg, David W. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Nielsen, Joseph W. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Norman, Daren R. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-07-01

The Korea Atomic Energy Research Institute is currently in the process of qualifying a Low-Enriched Uranium fuel element design for the new Ki-Jang Research Reactor (KJRR). As part of this effort, a prototype KJRR fuel element was irradiated for several operating cycles in the Northeast Flux Trap of the Advanced Test Reactor (ATR) at the Idaho National Laboratory. The KJRR fuel element contained a very large quantity of fissile material (618g 235U) in comparison with historical ATR experiment standards (<1g 235U), and its presence in the ATR flux trap was expected to create a neutronic configuration that would be well outside of the approved validation envelope for the reactor physics analysis methods used to support ATR operations. Accordingly it was necessary, prior to high-power irradiation of the KJRR fuel element in the ATR, to conduct an extensive set of new low-power physics measurements with the KJRR fuel element installed in the ATR Critical Facility (ATRC), a companion facility to the ATR that is located in an immediately adjacent building, sharing the same fuel handling and storage canal. The new measurements had the objective of expanding the validation envelope for the computational reactor physics tools used to support ATR operations and safety analysis to include the planned KJRR irradiation in the ATR and similar experiments that are anticipated in the future. The computational and experimental results demonstrated that the neutronic behavior of the KJRR fuel element in the ATRC is well-understood, both in terms of its general effects on core excess reactivity and fission power distributions, its effects on the calibration of the core lobe power measurement system, as well as in terms of its own internal fission rate distribution and total fission power per unit ATRC core power. Taken as a whole, these results have significantly extended the ATR physics validation envelope, thereby enabling an entire new class of irradiation experiments.

Experimental Characterization of Ultra-Wideband Channel Parameter Measurements in an Underground Mine

Directory of Open Access Journals (Sweden)

B. Nkakanou

2011-01-01

Full Text Available Experimental results for an ultra-wideband (UWB channel parameters in an underground mining environment over a frequency range of 3 GHz to 10 GHz are reported. The measurements were taken both in LOS and NLOS cases in two different size mine galleries. In the NLOS case, results were acquired for different corridor obstruction angles. The results were obtained during an extensive measurement campaign in the UWB frequency, and the measurement procedure allows both the large- and small-scale parameters such as the path loss exponent, coherence bandwidth, and so forth, to be quantified. The capacity of the UWB channel as a function of the physical depth of the mine gallery has also been recorded for comparison purposes.

Quantitative comparisons between experimentally measured 2-D carbon radiation and Monte Carlo impurity (MCI) code simulations

International Nuclear Information System (INIS)

Evans, T.E.; Leonard, A.W.; West, W.P.; Finkenthal, D.F.; Fenstermacher, M.E.; Porter, G.D.

1998-08-01

Experimentally measured carbon line emissions and total radiated power distributions from the DIII-D divertor and Scrape-Off Layer (SOL) are compared to those calculated with the Monte Carlo Impurity (MCI) model. A UEDGE background plasma is used in MCI with the Roth and Garcia-Rosales (RG-R) chemical sputtering model and/or one of six physical sputtering models. While results from these simulations do not reproduce all of the features seen in the experimentally measured radiation patterns, the total radiated power calculated in MCI is in relatively good agreement with that measured by the DIII-D bolometric system when the Smith78 physical sputtering model is coupled to RG-R chemical sputtering in an unaltered UEDGE plasma. Alternatively, MCI simulations done with UEDGE background ion temperatures along the divertor target plates adjusted to better match those measured in the experiment resulted in three physical sputtering models which when coupled to the RG-R model gave a total radiated power that was within 10% of measured value

Development and evaluation of measurement devices used to support testing of radioactive material transportation packages

International Nuclear Information System (INIS)

Uncapher, W.L.; Ammerman, D.J.; Stenberg, D.R.; Bronowski, D.R.; Arviso, M.

1992-01-01

Radioactive material package designers use structural testing to verify and demonstrate package performance. A major part of evaluating structural response is the collection of instrumentation measurement data. Sandia National Laboratories (SNL) has an ongoing program to develop and evaluate measurement devices to support testing of radioactive material packages. Measurement devices developed in support of this activity include evaluation channels, ruggedly constructed linear variable differential transformers, and piezoresistive accelerometers with enhanced measurement capabilities. In addition to developing measurement devices, a method has been derived to evaluate accelerometers and strain gages for measurement repeatability, ruggedness, and manufacturers' calibration data under both laboratory and field conditions. The developed measurement devices and evaluation technique will be discussed and the results of the evaluation will be presented

AN INVESTIGATION OF SUPPORT MEASURES FOR BEGINNING TEACHERS IN EU COUNTRIES AND TURKEY

Directory of Open Access Journals (Sweden)

Hilal Büyükgöze

2015-10-01

Full Text Available This paper investigates the support measures for beginning teachers, and elaborates on mentoring practices in European primary and secondary education institutions, and finally discusses induction practices in Turkey comparatively. The main findings of the research as follows: the common qualification for entry to teaching profession across Europe is a bachelor’s degree which generally last between four and five years, however initial teacher education is usually not sufficient for new teachers as they may experience and encounter problems about teaching, assessing and managing the students. Therefore, in almost more than the half of the European countries a structured induction program is carried out or other support measures are provided for new teachers. Few countries do not organize these programs at national level but at the local level or in schools. The structured induction programs are considered as a compulsory phase ending with a kind of overall assessment in most countries, whereas in some of them it is optional. These induction programs last from several months to 2 years, but the widespread length is about one year. The types of support measures for beginning teachers have been found to be differed across Europe, and mentoring is the most common form among these measures. The implications for educational organizations and teaching is discussed further

The development of human factors experimental evaluation techniques

Energy Technology Data Exchange (ETDEWEB)

Sim, Bong Shick; Oh, In Suk; Cha, Kyung Ho; Lee, Hyun Chul; Park, Geun Ok; Cheon, Se Woo; Suh, Sang Moon

1997-07-01

New human factors issues, such as evaluation of information navigation, the consideration of operator characteristics, and operator performance assessment, related to the HMI design based on VDUs are being risen. Thus, in order to solve these human factors issues, this project aims to establish the experimental technologies including the techniques for experimental design, experimental measurement, data collection and analysis, and to develop ITF (Integrated Test Facility) suitable for the experiment of HMI design evaluation. For the establish of the experimental data analysis and evaluation methodologies, we developed as the following: (1) a paradigm for human factors experimentation including experimental designs, procedures, and data analysis. (2) the methods for the assessment of operator`s mental workload (3) DAEXESS (data analysis and experiment evaluation supporting system). Also, we have established a experiment execution technologies through the preliminary experiments, such as the suitability evaluation of information display on a LSDP, the evaluation of information display on a LSDP, the evaluation of computerized operation procedure and an experiment of advanced alarm system (ADIOS). Finally, we developed the ITF including human machine simulator, telemetry system, an eye tracking system, an audio/video data measurement system, and three dimensional micro behaviour analysis system. (author). 81 refs., 68 tabs., 73 figs.

Experimental study of the response functions of direct-reading instruments measuring surface-area concentration of airborne nanostructured particles

International Nuclear Information System (INIS)

Bau, Sebastien; Witschger, Olivier; Gensdarmes, Francois; Thomas, Dominique

2009-01-01

An increasing number of experimental and theoretical studies focus on airborne nanoparticles (NP) in relation with many aspects of risk assessment to move forward our understanding of the hazards, the actual exposures in the workplace, and the limits of engineering controls and personal protective equipment with regard to NP. As a consequence, generating airborne NP with controlled properties constitutes an important challenge. In parallel, toxicological studies have been carried out, and most of them support the concept that surface-area could be a relevant metric for characterizing exposure to airborne NP. To provide NP surface-area concentration measurements, some direct-reading instruments have been designed, based on attachment rate of unipolar ions to NP by diffusion. However, very few information is available concerning the performances of these instruments and the parameters that could affect their responses. In this context, our work aims at characterizing the actual available instruments providing airborne NP surface-area concentration. The instruments (a- LQ1-DC, Matter Engineering; b-AeroTrak x2122 9000, TSI; c- NSAM, TSI model 3550;) are thought to be relevant for further workplace exposure characterization and monitoring. To achieve our work, an experimental facility (named CAIMAN) was specially designed, built and characterized.

Experimental study of the response functions of direct-reading instruments measuring surface-area concentration of airborne nanostructured particles

Energy Technology Data Exchange (ETDEWEB)

Bau, Sebastien; Witschger, Olivier [Institut National de Recherche et de Securite, INRS, Laboratoire de Metrologie des Aerosols, Rue du Morvan, CS 60027, 54519 Vandoeuvre Cedex (France); Gensdarmes, Francois [Institut de Radioprotection et de Surete Nucleaire, IRSN, Laboratoire de Physique et de Metrologie des Aerosols, BP 68, 91192 Gif-sur-Yvette Cedex (France); Thomas, Dominique [Laboratoire des Sciences du Genie Chimique, LSGC/CNRS, Nancy Universite, BP 2041, 54001 Nancy Cedex (France)], E-mail: sebastien.bau@inrs.fr

2009-05-01

An increasing number of experimental and theoretical studies focus on airborne nanoparticles (NP) in relation with many aspects of risk assessment to move forward our understanding of the hazards, the actual exposures in the workplace, and the limits of engineering controls and personal protective equipment with regard to NP. As a consequence, generating airborne NP with controlled properties constitutes an important challenge. In parallel, toxicological studies have been carried out, and most of them support the concept that surface-area could be a relevant metric for characterizing exposure to airborne NP. To provide NP surface-area concentration measurements, some direct-reading instruments have been designed, based on attachment rate of unipolar ions to NP by diffusion. However, very few information is available concerning the performances of these instruments and the parameters that could affect their responses. In this context, our work aims at characterizing the actual available instruments providing airborne NP surface-area concentration. The instruments (a- LQ1-DC, Matter Engineering; b-AeroTrak{sup x2122} 9000, TSI; c- NSAM, TSI model 3550;) are thought to be relevant for further workplace exposure characterization and monitoring. To achieve our work, an experimental facility (named CAIMAN) was specially designed, built and characterized.

A dual tracer ratio method for comparative emission measurements in an experimental dairy housing

Science.gov (United States)

Mohn, Joachim; Zeyer, Kerstin; Keck, Margret; Keller, Markus; Zähner, Michael; Poteko, Jernej; Emmenegger, Lukas; Schrade, Sabine

2018-04-01

Agriculture, and in particular dairy farming, is an important source of ammonia (NH3) and non-carbon dioxide greenhouse gas (GHG) emissions. This calls for the development and quantification of effective mitigation strategies. Our study presents the implementation of a dual tracer ratio method in a novel experimental dairy housing with two identical, but spatially separated housing areas. Modular design and flexible floor elements allow the assessment of structural, process engineering and organisational abatement measures at practical scale. Thereby, the emission reduction potential of specific abatement measures can be quantified in relation to a reference system. Emissions in the naturally ventilated housing are determined by continuous dosing of two artificial tracers (sulphur hexafluoride SF6, trifluoromethylsulphur pentafluoride SF5CF3) and their real-time detection in the ppt range with an optimized GC-ECD method. The two tracers are dosed into different experimental sections, which enables the independent assessment of both housing areas. Mass flow emissions of NH3 and GHGs are quantified by areal dosing of tracer gases and multipoint sampling as well as real-time analysis of both tracer and target gases. Validation experiments demonstrate that the technique is suitable for both areal and point emission sources and achieves an uncertainty of less than 10% for the mass emissions of NH3, methane (CH4) and carbon dioxide (CO2), which is superior to other currently available methods. Comparative emission measurements in this experimental dairy housing will provide reliable, currently unavailable information on emissions for Swiss dairy farming and demonstrate the reduction potential of mitigation measures for NH3, GHGs and potentially other pollutants.

Experimental design for reflection measurements of highly reactive liquid or solid substances with application to liquid sodium

International Nuclear Information System (INIS)

Chan, S.H.; Gossler, A.A.

1980-01-01

This technical report describes the experimental part of a program on thermal radiation properties of reactor materials. A versatile goniometer system with associated electronic components and mechanical instruments has been assembled. It is designed to measure spectral, specular reflectances of highly reactive liquid or solid substances over a spectral range of 0.3 μ to 9 μ and incidence angles of 12 0 to 30 0 off the normal direction. The capability of measuring reflectances of liquid substances clearly distinguishes this experimental design from conventional systems which are applicable only to solid substances. This design has been used to measure the spectral, specular reflectance of liquid sodium and preliminary results obtained are compared with those of solid sodium measured by other investigators

On the Dielectric Constant for Acetanilide: Experimental Measurements and Effect on Energy Transport

Science.gov (United States)

Careri, G.; Compatangelo, E.; Christiansen, P. L.; Halding, J.; Skovgaard, O.

1987-01-01

Experimental measurements of the dielectric constant for crystalline acetanilide powder for temperatures ranging from - 140°C to 20°C and for different hydration levels are presented. A Davydov-soliton computer model predicts dramatic changes in the energy transport and storage for typically increased values of the dielectric constant.

A new measure of dietary social support among African American adolescents

Science.gov (United States)

The purpose of this research was to develop and evaluate a measure of social support for fruit and vegetable (FV) consumption among economically disadvantaged African American adolescents. Focus groups (N = 30) and pilot testing procedures (N = 17) were used to develop and pretest questionnaire item...

A non-invasive experimental approach for surface temperature measurements on semi-crystalline thermoplastics

Science.gov (United States)

Boztepe, Sinan; Gilblas, Remi; de Almeida, Olivier; Le Maoult, Yannick; Schmidt, Fabrice

2017-10-01

Most of the thermoforming processes of thermoplastic polymers and their composites are performed adopting a combined heating and forming stages at which a precursor is heated prior to the forming. This step is done in order to improve formability by softening the thermoplastic polymer. Due to low thermal conductivity and semi-transparency of polymers, infrared (IR) heating is widely used for thermoforming of such materials. Predictive radiation heat transfer models for temperature distributions are therefore critical for optimizations of thermoforming process. One of the key challenges is to build a predictive model including the physical background of radiation heat transfer phenomenon in semi-crystalline thermoplastics as their microcrystalline structure introduces an optically heterogeneous medium. In addition, the accuracy of a predictive model is required to be validated experimentally where IR thermography is one of the suitable methods for such a validation as it provides a non-invasive, full-field surface temperature measurement. Although IR cameras provide a non-invasive measurement, a key issue for obtaining a reliable measurement depends on the optical characteristics of a heated material and the operating spectral band of IR camera. It is desired that the surface of a material to be measured has a spectral band where the material behaves opaque and an employed IR camera operates in the corresponding band. In this study, the optical characteristics of the PO-based polymer are discussed and, an experimental approach is proposed in order to measure the surface temperature of the PO-based polymer via IR thermography. The preliminary analyses showed that IR thermographic measurements may not be simply performed on PO-based polymers and require a correction method as their semi-transparent medium introduce a challenge to obtain reliable surface temperature measurements.

Review of nuclear data improvement needs for nuclear radiation measurement techniques used at the CEA experimental reactor facilities

Directory of Open Access Journals (Sweden)

Destouches Christophe

2016-01-01

Full Text Available The constant improvement of the neutron and gamma calculation codes used in experimental nuclear reactors goes hand in hand with that of the associated nuclear data libraries. The validation of these calculation schemes always requires the confrontation with integral experiments performed in experimental reactors to be completed. Nuclear data of interest, straight as cross sections, or elaborated ones such as reactivity, are always derived from a reaction rate measurement which is the only measurable parameter in a nuclear sensor. So, in order to derive physical parameters from the electric signal of the sensor, one needs specific nuclear data libraries. This paper presents successively the main features of the measurement techniques used in the CEA experimental reactor facilities for the on-line and offline neutron/gamma flux characterizations: reactor dosimetry, neutron flux measurements with miniature fission chambers and Self Power Neutron Detector (SPND and gamma flux measurements with chamber ionization and TLD. For each technique, the nuclear data necessary for their interpretation will be presented, the main identified needs for improvement identified and an analysis of their impact on the quality of the measurement. Finally, a synthesis of the study will be done.

Improvements in the measurement system of a biological Magnetic Induction Tomographical experimental setup

International Nuclear Information System (INIS)

Bras, N. B.; Martins, R. C.; Serra, A. C.

2010-01-01

Magnetic Induction Tomography (MIT) is an imaging technique that allows mapping the internal structure complex conductivity of a body. In this paper a feasibility study to implement a higher resolution MIT system for biological tissues is carried out. Recent improvements in measured signal stability and accuracy as well as a much improved angular resolution measurement of the multi-coil setup are presented which, together with a new mechanical design allows obtaining longer stable and more accurate acquisitions. This allows improving the number of measurements without trends or external perturbations, leading to a better conductivity resolution and to an enhanced image reconstruction. Throughout the paper experimental data is used to consolidate results.

Users’ support as a social resource in educational services: construct validity and measurement invariance of the User-Initiated Support Scale (UISS

Directory of Open Access Journals (Sweden)

Barbara Loera

2016-08-01

Full Text Available Social support is an important resource for reducing the risks of stress and burnout at work. It seems to be particularly helpful for educational and social professionals. The constant and intense relationships with users that characterize this kind of service can be very demanding, increasing stress and leading to burnout. While significant attention has been paid to supervisors and colleagues in the literature, users have rarely been considered as possible sources of social support. The only exception is the Zimmermann et al.’ (2011 research, focused on customer support as a resource for workers’ well-being. This paper proposes the validation of the customer-initiated support scale developed by Zimmermann et al. (2011, translated into Italian and focused on educational services users (children’s parents, to measure the user support perceived by workers: the User-Initiated Support Scale (UISS. In Study 1 (105 teachers, which specifically involved educators and kindergarten teachers, the items and scale properties were preliminarily examined using descriptive analyses and exploratory factor analysis (EFA. In Study 2 (304 teachers, the construct and criterion validity and scale dimensionality were analyzed using confirmatory factor analysis (CFA. In Study 3 (304 teachers from Study 2 and 296 educators, measurement invariance was tested. The EFA results from Study 1 showed a one-factor solution (explained variance, 67.2%. The scale showed good internal coherence (alpha = .88. The CFA in Study 2 validated the one-factor solution (CFI = .987; SRMR = .054. Bivariate correlations confirmed construct validity; the UISS was positively associated (convergent with user gratitude, and not associated (divergent with disproportionate customer expectations. Regarding the criterion validity test, the UISS was strongly correlated with burnout and job satisfaction. The analysis of measurement invariance performed on the Study 3 data confirmed the equality

Experimental Pressure Measurements on Hydropower Turbine Runners

Energy Technology Data Exchange (ETDEWEB)

Harding, Samuel F.; Richmond, Marshall C.

2017-04-28

The range of hydrodynamic operating conditions to which the turbine is exposed results in significant pressure fluctuations on both the pressure and suction sides of the blades. Understanding these dynamic pressures has a range of applications. Structurally, the resulting dynamic loads are significant in understanding the design life and maintenance schedule of the bearing, shafts and runner components. The pulsing pressures have also been seen to have a detrimental effect on the surface condition of the blades. Biologically, the pressure gradients and pressure extremes are the primary driver of barotrauma for fish passing through hydroturbines. Improvements in computational fluid dynamics (CFD) can be used to simulate such unsteady pressures in the regions of concern. High frequency model scale and prototype measurements of pressures at the blade are important in the validation of these models. Experimental characterization of pressure fields over hydroturbine blades has been demonstrated by a number of studies which using multiple pressure transducers to map the pressure contours on the runner blades. These have been performed at both model and prototype scales, often to validate computational models of the pressure and flow fields over the blades. This report provides a review of existing studies in which the blade pressure was measured in situ. The report assesses the technology for both model and prototype scale testing. The details of the primary studies in this field are reported and used to inform the types of hardware required for similar experiments based on the Ice Harbor Dam owned by the US Corps of Engineers on the Snake River, WA, USA. Such a study would be used to validate the CFD performed for the BioPA.

Measuring agreement between decision support reminders: the cloud vs. the local expert

OpenAIRE

Dixon, Brian Edward; Simonaitis, Linas; Perkins, Susan M; Wright, Adam; Middleton, Blackford

2014-01-01

Background: A cloud-based clinical decision support system (CDSS) was implemented to remotely provide evidence-based guideline reminders in support of preventative health. Following implementation, we measured the agreement between preventive care reminders generated by an existing, local CDSS and the new, cloud-based CDSS operating on the same patient visit data. Methods: Electronic health record data for the same set of patients seen in primary care were sent to both the cloud-based web ser...

Group support system and explanatory feedback: An experimental study of mitigating halo effect

Directory of Open Access Journals (Sweden)

Intiyas Utami

2015-12-01

Full Text Available Comprehensive assessment potentially leads to halo effect that will affect accuracy of auditors decision-making process. Biased initial audit decision will potentially influence final audit decision. It is there-fore necessary to mitigate halo effect that is the consequence of auditors good impression on clients initial condition. This re-search aims to empirically show that halo effect can be mitigated by explanatory feedback and Group Support System (GSS. The researchers experimentally mani-pulate explanatory feedback and GSS using online web-site. The subjects are stu-dents who have already taken auditing courses. The results show that: 1 explanato-ry feedback can mitigate halo effect so that audit decision will be more accurate 2 GSS can also mitigate halo effect 3 explanatory feedback and GSS are the best me-thods to mitigate halo effect.

Development of Assessment Tools To Measure Organizational Support for Employee Health.

Science.gov (United States)

Golaszewski, Thomas; Barr, Donald; Pronk, Nico

2003-01-01

Describes one working group's attempts to develop and utilize assessment tools for measuring and changing organizational support for employee health. Originally designed as part of a heart health related intervention, the system has evolved into a managed care evaluation and major chronic disease inventory. Findings indicate the potential of…

How experimental biology and ecology can support evidence-based decision-making in conservation: avoiding pitfalls and enabling application.

Science.gov (United States)

Cooke, Steven J; Birnie-Gauvin, Kim; Lennox, Robert J; Taylor, Jessica J; Rytwinski, Trina; Rummer, Jodie L; Franklin, Craig E; Bennett, Joseph R; Haddaway, Neal R

2017-01-01

Policy development and management decisions should be based upon the best available evidence. In recent years, approaches to evidence synthesis, originating in the medical realm (such as systematic reviews), have been applied to conservation to promote evidence-based conservation and environmental management. Systematic reviews involve a critical appraisal of evidence, but studies that lack the necessary rigour (e.g. experimental, technical and analytical aspects) to justify their conclusions are typically excluded from systematic reviews or down-weighted in terms of their influence. One of the strengths of conservation physiology is the reliance on experimental approaches that help to more clearly establish cause-and-effect relationships. Indeed, experimental biology and ecology have much to offer in terms of building the evidence base that is needed to inform policy and management options related to pressing issues such as enacting endangered species recovery plans or evaluating the effectiveness of conservation interventions. Here, we identify a number of pitfalls that can prevent experimental findings from being relevant to conservation or would lead to their exclusion or down-weighting during critical appraisal in a systematic review. We conclude that conservation physiology is well positioned to support evidence-based conservation, provided that experimental designs are robust and that conservation physiologists understand the nuances associated with informing decision-making processes so that they can be more relevant.

Experimentally measured susceptibility to peer influence and adolescent sexual behavior trajectories : A preliminary study

NARCIS (Netherlands)

Choukas-Bradley, S.; Giletta, M.; Widman, L.; Cohen, G.L.; Prinstein, M.J.

2014-01-01

A performance-based measure of peer influence susceptibility was examined as a moderator of the longitudinal association between peer norms and trajectories of adolescents' number of sexual intercourse partners. Seventy-one 9th grade adolescents (52% female) participated in an experimental "chat

In-situ tuff water migration/heater experiment: experimental plan

International Nuclear Information System (INIS)

Johnstone, J.K.

1980-08-01

Tuffs on the Nevada Test Site (NTS) are currently under investigation as a potential isolation medium for heat-producing nuclear wastes. The National Academy of Sciences has concurred in our identification of the potentially large water content (less than or equal to 40 vol %) of tuffs as one of the important issues affecting their suitability for a repository. This Experimental Plan describes an in-situ experiment intended as an initial assessment of water generation/migration in response to a thermal input. The experiment will be conducted in the Grouse Canyon Welded Tuff in Tunnel U12g (G-Tunnel) located in the north-central region of the NTS. While the Grouse Canyon Welded Tuff is not a potential repository medium, it has physical, thermal, and mechanical properties very similar to those tuffs currently under consideration and is accessible at depth (400 m below the surface) in an existing facility. Other goals of the experiment are to support computer-code and instrumentation development, and to measure in-situ thermal properties. The experimental array consists of a central electrical heater, 1.2 m long x 10.2 cm diameter, surrounded by three holes for measuring water-migration behavior, two holes for measuring temperature profiles, one hole for measuring thermally induced stress in the rock, and one hole perpendicular to the heater to measure displacement with a laser. This Experimental Plan describes the experimental objectives, the technical issues, the site, the experimental array, thermal and thermomechanical modeling results, the instrumentation, the data-acquisition system, posttest characterization, and the organizational details

Evaluating the INSPIRE measure of staff support for personal recovery in a Swedish psychiatric context.

Science.gov (United States)

Schön, Ulla-Karin; Svedberg, Petra; Rosenberg, David

2015-05-01

Recovery is understood to be an individual process that cannot be controlled, but can be supported and facilitated at the individual, organizational and system levels. Standardized measures of recovery may play a critical role in contributing to the development of a recovery-oriented system. The INSPIRE measure is a 28-item service user-rated measure of recovery support. INSPIRE assesses both the individual preferences of the user in the recovery process and their experience of support from staff. The aim of this study was to evaluate the psychometric properties of the Swedish version of the INSPIRE measure, for potential use in Swedish mental health services and in order to promote recovery in mental illness. The sample consisted of 85 participants from six community mental health services targeting people with a diagnosis of psychosis in a municipality in Sweden. For the test-retest evaluation, 78 participants completed the questionnaire 2 weeks later. The results in the present study indicate that the Swedish version of the INSPIRE measure had good face and content validity, satisfactory internal consistency and some level of instability in test-retest reliability. While further studies that test the instrument in a larger and more diverse clinical context are needed, INSPIRE can be considered a relevant and feasible instrument to utilize in supporting the development of a recovery-oriented system in Sweden.

Experimental measurements and modelling of the WEGA boundary layer plasma

International Nuclear Information System (INIS)

El Shaer, M.; Ichtchenko, G.

1983-02-01

The boundary layer of the WEGA Tokamak has been investigated by using specific diagnostics: movable 4 mm microwave interferometer, several types of movable and fixed probes, Katsumata probe, and multigrid electrostatic analyzer. During the RF heating at the lower hybrid frequency, some modifications in the parameters of the boundary layer are observed which are interpreted by the ponderomotive force effects. A comparison between the measured reflection coefficients of the grill waveguides and their predicted values by a coupling theory (not taking into account the real conditions facing the Grill) is presented. A diffusion model was also made to describe this particular region and to fit the experimental results

Experimental damping assessment of a full scale offshore mono bucket foundation

DEFF Research Database (Denmark)

Gres, Szymon; Fejerskov, Morten; Ibsen, Lars Bo

2016-01-01

This paper quantifies the system damping of a offshore meteorological mast supported by a Mono Bucket foundation based on a long-term experimental campaign. The structure is located at Dogger Bank west, North Sea, and equipped with a measurement system monitoring acceleration, strain, inclination...

Modeling of a pitching and plunging airfoil using experimental flow field and load measurements

Science.gov (United States)

Troshin, Victor; Seifert, Avraham

2018-01-01

The main goal of the current paper is to outline a low-order modeling procedure of a heaving airfoil in a still fluid using experimental measurements. Due to its relative simplicity, the proposed procedure is applicable for the analysis of flow fields within complex and unsteady geometries and it is suitable for analyzing the data obtained by experimentation. Currently, this procedure is used to model and predict the flow field evolution using a small number of low profile load sensors and flow field measurements. A time delay neural network is used to estimate the flow field. The neural network estimates the amplitudes of the most energetic modes using four sensory inputs. The modes are calculated using proper orthogonal decomposition of the flow field data obtained experimentally by time-resolved, phase-locked particle imaging velocimetry. To permit the use of proper orthogonal decomposition, the measured flow field is mapped onto a stationary domain using volume preserving transformation. The analysis performed by the model showed good estimation quality within the parameter range used in the training procedure. However, the performance deteriorates for cases out of this range. This situation indicates that, to improve the robustness of the model, both the decomposition and the training data sets must be diverse in terms of input parameter space. In addition, the results suggest that the property of volume preservation of the mapping does not affect the model quality as long as the model is not based on the Galerkin approximation. Thus, it may be relaxed for cases with more complex geometry and kinematics.

Routine outcome measurement in mental health service consumers: who should provide support for the self-assessments?

Science.gov (United States)

Gelkopf, Marc; Pagorek-Eshel, Shira; Trauer, Tom; Roe, David

2015-06-01

This study examined whether mental health community service users completed outcome self-reports differently when assessments were supervised by internal vs. external staff. The examination of potential differences between the two has useful implications for mental health systems that take upon themselves the challenge of Routine Outcome Measurement (ROM), as it might impact allocation of public resources and managed care program planning. 73 consumers completed the Manchester Short Assessment of Quality of Life (MANSA), a shortened version of the Recovery Assessment Scale (RAS), and a functioning questionnaire. Questionnaires were administered, once using support provided by internal staff and once using support provided by external professional staff, with a one-month time interval and in random order. A MANOVA Repeated Measures showed no differences in outcomes of quality of life and recovery between internal and external support. Functioning scores were higher for the internal support when the internal assessments were performed first. Overall, except for the differences in functioning assessment, outcome scores were not determined by the supporting agency. This might indicate that when measuring quality of life and recovery, different supporting methods can be used to gather outcome measures and internal staff might be a good default agency to do this. Differences found in functioning assessment are discussed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Experimentally Measured Susceptibility to Peer Influence and Adolescent Sexual Behavior Trajectories: A Preliminary Study

Science.gov (United States)

Choukas-Bradley, Sophia; Giletta, Matteo; Widman, Laura; Cohen, Geoffrey L.; Prinstein, Mitchell J.

2014-01-01

A performance-based measure of peer influence susceptibility was examined as a moderator of the longitudinal association between peer norms and trajectories of adolescents' number of sexual intercourse partners. Seventy-one 9th grade adolescents (52% female) participated in an experimental "chat room" paradigm involving…

Measurement Space Drill Support

Science.gov (United States)

2015-08-30

II) H-47 Block II (I) *H-47 Block II (II) AVN FVL Att (I) * AVN FVL Att (II) TRAC- MTRY F2025B Logistic Flow MS Drill Support FY15 Research...does not have to use other AVN /ground assets to cover the area, freeing these assets to perform other missions and potentially enhancing the

The measurement of social support in the "European Research on Incapacitating Diseases and Social Support": the development of the Social Support Questionnaire for Transactions (SSQT)

NARCIS (Netherlands)

Suurmeijer, Theo P; Doeglas, Dirk M; Briancon, Serge; Krijnen, Wim P

1995-01-01

Investigated if the SSQT allows for meaningful comparisons between patients with rheumatoid arthritis from different countries and explored the dimensionality and invariance of the SSQT dimensions. Based on types of social support, the authors formulated a series of items to measure actual

Measuring Diagnostic Stand for Experimental Researches in Technology Machining

Directory of Open Access Journals (Sweden)

A. E. Dreval'

2014-01-01

Full Text Available The paper reviews applied techniques, methods, and structure of the control and measuring means to conduct experimental and scientific researches of cutting processes. Existing research methods in cutting the metals are divided by features, such as essence of methods, the number of records of physical indicators, the number of studied factors, duration of tests. The groups of methods are briefly characterized.The chair "Tool Engineering and Technologies" of BMSTU developed and made a diagnostic stand of control and measurements for conducting research activities in the field of materials processing technology by cutting to define rational technological decisions, when machining, and carry out an analysis of efficiency and economic feasibility of made decisions. The diagnostic stand contains modern the electronic equipment. Record of measuring parameters is made in real time with a possibility for visual representation of read results and mathematical and statistical processing of measurement results. The stand can be used in research laboratories of machine-building enterprises, laboratories of higher education institutions, and other scientific divisions.The paper presents a justification that the stand is reasonable to use for the following: completion and choice of rational cutting modes, workability assessment of new constructional materials, technical and operational characteristics of the processed surfaces, and operational properties of the cutting tools of various producers, choice of optimum geometrical parameters of the cutting tools and brands of the lubricant cooling technological means, as well as the energy consumption for the chosen machining process. The stand allows us to make an assessment of wear resistance and tribology-technical characteristics of tool materials, as well as an accuracy, rigidity, vibration stability of machines, both new and being in operation.

Volumetric properties of the (tetrahydrofuran + water) and (tetra-n-butyl ammonium bromide + water) systems: Experimental measurements and correlations

International Nuclear Information System (INIS)

Belandria, Veronica; Mohammadi, Amir H.; Richon, Dominique

2009-01-01

In this communication, we report experimental density data for the binary mixtures of (water + tetrahydrofuran) and (water + tetra-n-butyl ammonium bromide) at atmospheric pressure and various temperatures. The densities were measured using an Anton Paar TM digital vibrating-tube densimeter. For the (tetrahydrofuran + water) system, excess molar volumes have been calculated using the experimental densities and correlated using the Redlich-Kister equation. The Redlich-Kister equation parameters have been adjusted on experimental results. The partial molar volumes and partial excess molar volumes at infinite dilution have also been calculated for each component. A simple density equation was finally applied to correlate the measured density of the (tetra-n-butyl ammonium bromide + water) system.

Experimental study of a swept reflectometer with a single antenna for plasma density profile measurement

International Nuclear Information System (INIS)

Calderon, M.A.G.; Simonet, F.

1984-12-01

The feasibility of a swept microwave reflectometer, with one antenna only, for plasma electron density measurement is studied. Experimental results obtained in the laboratory by simulating the plasma with a metallic mirror are presented

The structure of social exchange in self-help support groups: development of a measure.

Science.gov (United States)

Brown, Louis D; Tang, Xiaohui; Hollman, Ruth L

2014-03-01

Self-help support groups are indigenous community resources designed to help people manage a variety of personal challenges, from alcohol abuse to xeroderma pigmentosum. The social exchanges that occur during group meetings are central to understanding how people benefit from participation. This paper examines the different types of social exchange behaviors that occur during meetings, using two studies to develop empirically distinct scales that reliably measure theoretically important types of exchange. Resource theory informed the initial measurement development efforts. Exploratory factor analyses from the first study led to revisions in the factor structure of the social exchange scales. The revised measure captured the exchange of emotional support, experiential information, humor, unwanted behaviors, and exchanges outside meetings. Confirmatory factor analyses from a follow-up study with a different sample of self-help support groups provided good model fit, suggesting the revised structure accurately represented the data. Further, the scales demonstrated good convergent and discriminant validity with related constructs. Future research can use the scales to identify aspects of social exchange that are most important in improving health outcomes among self-help support group participants. Groups can use the scales in practice to celebrate strengths and address weaknesses in their social exchange dynamics.

Experimental study of an electromagnetic flow meter for liquid metals based on torque measurement during pumping process

International Nuclear Information System (INIS)

Dubovikova, N; Kolesnikov, Y; Karcher, Ch

2015-01-01

This paper presents a detailed experimental study on an electromagnetic flow measurement technique to measure the flow rate of liquid metals. The experimental setup consists of a contactless electromagnetic pump with a torque sensor mounted on the pump shaft. The electromagnetic pump is composed of two rotating steel discs having embedded permanent magnets with alternating poles. The rotation of the discs creates a travelling sinusoidal magnetic field and eddy currents within the liquid metal. The metal is contained inside the duct located between the discs of the pump. The interaction of the magnetic field and the induced eddy currents generates an electromagnetic Lorentz force providing the pumping effect. The flow rate is proportional to this force. The torque sensor measures the moment of the discs due to the Lorentz force, which is converted to a flow rate value. We name the method Lorentz torque velocimetry (LTV). The full calibration procedure and experimental investigation of the LTV are described. The method can be used as a non-contact flow rate control technique for liquid metals. (paper)

Simulation and Experimental Investigations on the Strain Measurement of the Uniform Strength Beam Using a FBG sensor

International Nuclear Information System (INIS)

Tu Yumeng; Gong Huaping; Chen Jixuan; Jin Yongxing

2011-01-01

The model of force analysis on a uniform strength beam is built by the general finite element program (ANSYS software). The flexivity profile produced by uniform strength beam with different forces is simulated by ANSYS software. In experiment, a fiber Bragg grating sensor is fixed on the uniform strength beam with modified acrylate. The flexivity and strain are varied by changing the load on the end of the beam. The strain of the uniform strength beam is measured with FBG when applied force is varied from 2.45N to14.7N with a step of 2.45N. Both the simulated and experimental results show that, the strain induced by the uniform strength beam is linear with the load force. The sensitivity is 18.32με/N for experimental measurement, and 19.72με/N for simulation. The experimental results are consistent with the simulation results, with the maximum measurement error of strain being 7.4%. It indicates that, the FBG sensor fixed with modified acrylate is proved to be effectively and reliably in the applications of civil engineering.

Internet peer support for individuals with psychiatric disabilities: A randomized controlled trial.

Science.gov (United States)

Kaplan, Katy; Salzer, Mark S; Solomon, Phyllis; Brusilovskiy, Eugene; Cousounis, Pamela

2011-01-01

Despite the prevalence of Internet support groups for individuals with mental illnesses little is known about the potential benefits, or harm, of participating in such groups. Therefore, this randomized controlled trial sought to determine the impact of unmoderated, unstructured Internet peer support, similar to what is naturally occurring on the Internet, on the well-being of individuals with psychiatric disabilities. Three hundred individuals resident in the USA diagnosed with a Schizophrenia Spectrum or an Affective Disorder were randomized into one of three conditions: experimental Internet peer support via a listserv, experimental Internet peer support via a bulletin board, or a control condition. Three measurement time points, baseline, 4- and 12 months post-baseline, assessed well-being by examining measures of recovery, quality of life, empowerment, social support, and distress. Time × group interactions in the repeated measures ANOVA showed no differences between conditions on the main outcomes. Post-hoc repeated measures ANOVAs found that those individuals who participated more in Internet peer support reported higher levels of distress than those with less or no participation (p = 0.03). Those who reported more positive experiences with the Internet peer support group also reported higher levels of psychological distress than those reporting less positive experiences (p = 0.01). Study results therefore do not support the hypothesis that participation in an unmoderated, unstructured Internet listserv or bulletin board peer support group for individuals with psychiatric disabilities enhances well-being. Counterintuitive findings demonstrating those who report more positive experiences also experienced higher levels of distress are discussed but we also point to the need for additional research. Future research should explore the various structures, formats, and interventions of Internet support, as well as the content and quality of interactions

Uncertainty analysis and flow measurements in an experimental mock-up of a molten salt reactor concept

Energy Technology Data Exchange (ETDEWEB)

Yamaji, Bogdan; Aszodi, Attila [Budapest University of Technology and Economics (Hungary). Inst. of Nuclear Techniques

2016-09-15

In the paper measurement results from the experimental modelling of a molten salt reactor concept will be presented along with detailed uncertainty analysis of the experimental system. Non-intrusive flow measurements are carried out on the scaled and segmented mock-up of a homogeneous, single region molten salt fast reactor concept. Uncertainty assessment of the particle image velocimetry (PIV) measurement system applied with the scaled and segmented model is presented in detail. The analysis covers the error sources of the measurement system (laser, recording camera, etc.) and the specific conditions (de-warping of measurement planes) originating in the geometry of the investigated domain. Effect of sample size in the ensemble averaged PIV measurements is discussed as well. An additional two-loop-operation mode is also presented and the analysis of the measurement results confirm that without enhancement nominal and other operation conditions will lead to strong unfavourable separation in the core flow. It implies that use of internal flow distribution structures will be necessary for the optimisation of the core coolant flow. Preliminary CFD calculations are presented to help the design of a perforated plate located above the inlet region. The purpose of the perforated plate is to reduce recirculation near the cylindrical wall and enhance the uniformity of the core flow distribution.

Development of a wearable measurement and control unit for personal customizing machine-supported exercise.

Science.gov (United States)

Wang, Zhihui; Tamura, Naoki; Kiryu, Tohru

2005-01-01

Wearable technology has been used in various health-related fields to develop advanced monitoring solutions. However, the monitoring function alone cannot meet all the requirements of personal customizing machine-supported exercise that have biosignal-based controls. In this paper, we propose a new wearable unit design equipped with measurement and control functions to support the personal customization process. The wearable unit can measure the heart rate and electromyogram signals during exercise and output workload control commands to the exercise machines. We then applied a prototype of the wearable unit to an Internet-based cycle ergometer system. The wearable unit was examined using twelve young people to check its feasibility. The results verified that the unit could successfully adapt to the control of the workload and was effective for continuously supporting gradual changes in physical activities.

Software support for environmental measurement in quality at educational institutions

Directory of Open Access Journals (Sweden)

Alena Pauliková

2016-03-01

Full Text Available The analysed theme of this article is based on the training of environmental measurements for workplaces. This is very important for sustainable quality in technical educational institutions. Applied kinds of software, which are taught at technical educational institutions, have to offer the professional and methodical knowledge concerning conditions of working ambient for students of selected technical specialisations. This skill is performed in such a way that the graduates, after entering the practical professional life, will be able to participate in solutions for actual problems that are related to environmental protection by means of software support. Nowadays, during the training processit is also obligatory to introduce technical science. Taking into consideration the above-mentioned facts it is possible to say that information technology support for environmental study subjects is a relevant aspect, which should be integrated into the university educational process. There is an effective progress that further highlights the focus on the quality of university education not only for environmental engineers. Actual trends require an increasing number of software/hardware educated engineers who can participate in qualitative university preparation, i.e.IT environmentalists. The Department of Environmental Engineering at the Faculty of Mechanical Engineering, TechnicalUniversity in Košice, Slovakia is an institution specified and intended for quality objectivisation. This institution introduced into the study programmes (“Environmental Management” and “Technology of Environmental Protection” study subjects with the software support, which are oriented towards outdoor and indoor ambient and in this way the Department of Process and Environmental Engineering is integrated effectively and intensively into the area of measurement training with regard to the requirement of quality educational processes.

Establishment of Experimental Equipment for Training of Professionals in the Nuclear Radiation Measurement

Energy Technology Data Exchange (ETDEWEB)

Ahn, S. K.; Seo, K. W.; Joo, Y. C.; Kim, I. C.; Woo, C. K.; Yoo, B. H. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2008-09-15

The main purpose of this project is to establish experimental equipment for training of professionals and students in the field of radiation measurement, and settle the foundation for the advanced education system and program. The priority for the experimental equipment had been deduced by reviewing of the Nuclear Training and Education Center of KAERI and other country's training courses. Equipment for training of radiation professionals are High-Purity Germanium spectroscopic systems, alpha analyzers, and hand-held gamma/neutron inspector systems. For the basic experiments, electric personal dosimeters and a reader, radiation survey meters, and various alpha, beta and gamma radiation isotopes have been equipped. Some old or disused equipment and devices were disposed and re-arranged, and a new experiment lab had been settled for gamma spectroscopy. Along with the preparation of equipment, 14 experimental modules have been selected for practical and essential experiments training to professionals from industries, universities and research organizations. Among the modules, 7 important experiment notes had been prepared in Korea and also in English. As a consequence, these advanced radiation experimental setting would be a basis to cooperate with IAEA or other countries for international training courses. These activities would be a foundation for our contribution to the international nuclear society and for improving our nuclear competitiveness. The experimental equipment and application notes developed in this study will be used also by other training institutes and educational organizations through introducing and encouraging to use them to the nuclear society.

Establishment of Experimental Equipment for Training of Professionals in the Nuclear Radiation Measurement

International Nuclear Information System (INIS)

Ahn, S. K.; Seo, K. W.; Joo, Y. C.; Kim, I. C.; Woo, C. K.; Yoo, B. H.

2008-09-01

The main purpose of this project is to establish experimental equipment for training of professionals and students in the field of radiation measurement, and settle the foundation for the advanced education system and program. The priority for the experimental equipment had been deduced by reviewing of the Nuclear Training and Education Center of KAERI and other country's training courses. Equipment for training of radiation professionals are High-Purity Germanium spectroscopic systems, alpha analyzers, and hand-held gamma/neutron inspector systems. For the basic experiments, electric personal dosimeters and a reader, radiation survey meters, and various alpha, beta and gamma radiation isotopes have been equipped. Some old or disused equipment and devices were disposed and re-arranged, and a new experiment lab had been settled for gamma spectroscopy. Along with the preparation of equipment, 14 experimental modules have been selected for practical and essential experiments training to professionals from industries, universities and research organizations. Among the modules, 7 important experiment notes had been prepared in Korea and also in English. As a consequence, these advanced radiation experimental setting would be a basis to cooperate with IAEA or other countries for international training courses. These activities would be a foundation for our contribution to the international nuclear society and for improving our nuclear competitiveness. The experimental equipment and application notes developed in this study will be used also by other training institutes and educational organizations through introducing and encouraging to use them to the nuclear society

The Numerical Calculation and Experimental Measurement of the Inductance Parameters for Permanent Magnet Synchronous Motor in Electric Vehicle

Science.gov (United States)

Jiang, Chao; Qiao, Mingzhong; Zhu, Peng

2017-12-01

A permanent magnet synchronous motor with radial magnetic circuit and built-in permanent magnet is designed for the electric vehicle. Finite element numerical calculation and experimental measurement are adopted to obtain the direct axis and quadrature axis inductance parameters of the motor which are vital important for the motor control. The calculation method is simple, the measuring principle is clear, the results of numerical calculation and experimental measurement are mutual confirmation. A quick and effective method is provided to obtain the direct axis and quadrature axis inductance parameters of the motor, and then improve the design of motor or adjust the control parameters of the motor controller.

COMPARATIVE KINEMATIC MEASURES OF TREADMILL RUNNING WITH OR WITHOUT BODY WEIGHT SUPPORT IN RUNNERS

Directory of Open Access Journals (Sweden)

Duane Millslagle

2005-12-01

Full Text Available Treadmill walking and running using a supportive harness has been used as a training method to rehabilitate injured patients' walking or running gait. Comparison of full weight support (FWS and body weight support (BWS kinematic measures in competitive runners has received little attention. The purpose of this study was to compare selected FWS to BWS kinematic measures in healthy competitive runners. Ten male runners (age = 21.4 ± 1.5 years with a training regimen averaging 64 km per week at 3.8 m·s-1 participated. All participants ran three 3-minute trials. The randomized trial conditions were: FWS, 20% BWS, and 40% BWS. All conditions were videotaped with 2 cameras and a 21-point, 3-D model was generated for analysis. From the position-time data, cycle length (CL, cycle frequency (CF, time of contact (TC, hip-, knee-, ankle- range of motion in degrees (H-ROM, K-ROM, and A-ROM, respectively, and vertical displacement of the center of mass (COM were derived and compared. With increasing support conditions, cycle length increased. Cycle frequency, hip and ankle angle ranges, and COM vertical displacement decreased (p 0.05. BWS running produced significant changes in selected kinematic measures. These changes may provide insight into runners' behavior when using BWS in training or recovery from competition. Additional investigation of BWS training affect with competitive runners would be recommended

An experimental method for making spectral emittance and surface temperature measurements of opaque surfaces

International Nuclear Information System (INIS)

Moore, Travis J.; Jones, Matthew R.; Tree, Dale R.; Daniel Maynes, R.; Baxter, Larry L.

2011-01-01

An experimental procedure has been developed to make spectral emittance and temperature measurements. The spectral emittance of an object is calculated using measurements of the spectral emissive power and of the surface temperature of the object obtained using a Fourier transform infrared (FTIR) spectrometer. A calibration procedure is described in detail which accounts for the temperature dependence of the detector. The methods used to extract the spectral emissive power and surface temperature from measured infrared spectra were validated using a blackbody radiator at known temperatures. The average error in the measured spectral emittance was 2.1% and the average difference between the temperature inferred from the recorded spectra and the temperature indicated on the blackbody radiator was 1.2%. The method was used to measure the spectral emittance of oxidized copper at various temperatures.

Measurement and control system for cryogenic helium gas bearing turbo-expander experimental platform based on Siemens PLC S7-300

Energy Technology Data Exchange (ETDEWEB)

Li, J.; Xiong, L. Y.; Peng, N.; Dong, B.; Liu, L. Q. [Key Laboratory of Cryogenics, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing, 100190 (China); Wang, P. [Beijing Sciample Technology Co., Ltd., Beijing, 100190 (China)

2014-01-29

An experimental platform for cryogenic Helium gas bearing turbo-expanders is established at the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. This turbo-expander experimental platform is designed for performance testing and experimental research on Helium turbo-expanders with different sizes from the liquid hydrogen temperature to the room temperature region. A measurement and control system based on Siemens PLC S7-300 for this turbo-expander experimental platform is developed. Proper sensors are selected to measure such parameters as temperature, pressure, rotation speed and air flow rate. All the collected data to be processed are transformed and transmitted to S7-300 CPU. Siemens S7-300 series PLC CPU315-2PN/DP is as master station and two sets of ET200M DP remote expand I/O is as slave station. Profibus-DP field communication is established between master station and slave stations. The upper computer Human Machine Interface (HMI) is compiled using Siemens configuration software WinCC V6.2. The upper computer communicates with PLC by means of industrial Ethernet. Centralized monitoring and distributed control is achieved. Experimental results show that this measurement and control system has fulfilled the test requirement for the turbo-expander experimental platform.

Measurement and control system for cryogenic helium gas bearing turbo-expander experimental platform based on Siemens PLC S7-300

Science.gov (United States)

Li, J.; Xiong, L. Y.; Peng, N.; Dong, B.; Wang, P.; Liu, L. Q.

2014-01-01

An experimental platform for cryogenic Helium gas bearing turbo-expanders is established at the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. This turbo-expander experimental platform is designed for performance testing and experimental research on Helium turbo-expanders with different sizes from the liquid hydrogen temperature to the room temperature region. A measurement and control system based on Siemens PLC S7-300 for this turbo-expander experimental platform is developed. Proper sensors are selected to measure such parameters as temperature, pressure, rotation speed and air flow rate. All the collected data to be processed are transformed and transmitted to S7-300 CPU. Siemens S7-300 series PLC CPU315-2PN/DP is as master station and two sets of ET200M DP remote expand I/O is as slave station. Profibus-DP field communication is established between master station and slave stations. The upper computer Human Machine Interface (HMI) is compiled using Siemens configuration software WinCC V6.2. The upper computer communicates with PLC by means of industrial Ethernet. Centralized monitoring and distributed control is achieved. Experimental results show that this measurement and control system has fulfilled the test requirement for the turbo-expander experimental platform.

Experimental prediction of tube support interaction characteristics in steam generators: Volume 2, Westinghouse Model 51 flow entrance region: Topical report

International Nuclear Information System (INIS)

Haslinger, K.H.

1988-06-01

Tube-to-tube support interaction characterisitics were determined experimentally on a single tube, multi-span geometry, representative of the Westinghouse Model 51 steam generator economizer design. Results, in part, became input for an autoclave type wear test program on steam generator tubes, performed by Kraftwerk Union (KWU). More importantly, the test data reported here have been used to validate two analytical wear prediction codes; the WECAN code, which was developed by Westinghouse, and the ABAQUS code which has been enhanced for EPRI by Foster Wheeler to enable simulation of gap conditions (including fluid film effects) for various support geometries

Experimental and numerical investigation of the flow measurement method utilized in the steam generator of HTR-PM

Energy Technology Data Exchange (ETDEWEB)

Wang, Shiming; Ren, Cheng; Sun, Yangfei [Institute of Nuclear and New Energy Technology of Tsinghua University, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Beijing 100084 (China); Tu, Jiyuan [Institute of Nuclear and New Energy Technology of Tsinghua University, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Beijing 100084 (China); School of Aerospace, Mechanical & Manufacturing Engineering, RMIT University, Melbourne, VIC 3083 (Australia); Yang, Xingtuan, E-mail: yangxt107@sina.com [Institute of Nuclear and New Energy Technology of Tsinghua University, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Beijing 100084 (China)

2016-08-15

Highlights: • The flow confluence process in the steam generator is very important for HTR-PM. • The complicated flow in the unique pipeline configuration is studied by both of experimental and numerical method. • The pressure uniformity at the bottom of the model was tested to evaluate the accuracy of the experimental results. • Flow separation and the secondary flow is described for explaining the nonuniformity of the flow distribution. - Abstract: The helium flow measurement method is very important for the design of HTR-PM. Water experiments and numerical simulation with a 1/5 scaled model are conducted to investigate the flow measurement method utilized in the steam generator of HTR-PM. Pressure information at specific location of the 90° elbows with the diameter of 46.75 mm and radius ratio of 1.5 is measured to evaluate the flow rate in the riser-pipes. Pressure uniformity at the bottom of the experimental apparatus is tested to evaluate the influence of the equipment error on the final experimental results. Numerical results obtained by using the realizable k–ε model are compared with the experimental data. The results reveal that flow oscillation does not occur in the confluence system. For every single riser-pipe, the flow is stable despite the nonuniformity of the flow distribution. The average flow rates of the two pipe series show good repeatability regardless of the increases and decreases of the average velocity. In the header box, the flows out of the riser-pipes encounter with each other and finally distort the pressure distribution and the nonuniformity of the flow distribution becomes more significant along with the increasing Reynolds number.

A heat transport benchmark problem for predicting the impact of measurements on experimental facility design

International Nuclear Information System (INIS)

Cacuci, Dan Gabriel

2016-01-01

Highlights: • Predictive Modeling of Coupled Multi-Physics Systems (PM_CMPS) methodology is used. • Impact of measurements for reducing predicted uncertainties is highlighted. • Presented thermal-hydraulics benchmark illustrates generally applicable concepts. - Abstract: This work presents the application of the “Predictive Modeling of Coupled Multi-Physics Systems” (PM_CMPS) methodology conceived by Cacuci (2014) to a “test-section benchmark” problem in order to quantify the impact of measurements for reducing the uncertainties in the conceptual design of a proposed experimental facility aimed at investigating the thermal-hydraulics characteristics expected in the conceptual design of the G4M reactor (GEN4ENERGY, 2012). This “test-section benchmark” simulates the conditions experienced by the hottest rod within the conceptual design of the facility's test section, modeling the steady-state conduction in a rod heated internally by a cosinus-like heat source, as typically encountered in nuclear reactors, and cooled by forced convection to a surrounding coolant flowing along the rod. The PM_CMPS methodology constructs a prior distribution using all of the available computational and experimental information, by relying on the maximum entropy principle to maximize the impact of all available information and minimize the impact of ignorance. The PM_CMPS methodology then constructs the posterior distribution using Bayes’ theorem, and subsequently evaluates it via saddle-point methods to obtain explicit formulas for the predicted optimal temperature distributions and predicted optimal values for the thermal-hydraulics model parameters that characterized the test-section benchmark. In addition, the PM_CMPS methodology also yields reduced uncertainties for both the model parameters and responses. As a general rule, it is important to measure a quantity consistently with, and more accurately than, the information extant prior to the measurement. For

Trade policy responses to food price crisis and implications for existing domestic support measures

DEFF Research Database (Denmark)

Yu, Wusheng; Jensen, Hans Grinsted

2014-01-01

jointly moderated rises of domestic grain prices. In particular, domestic and trade measures on key agricultural inputs such as fertilizers are shown to contribute significantly to expand grain outputs and reduce domestic market prices. While the short-term goal in stabilizing domestic grain prices......Many national governments around the world applied export restrictions in order to achieve domestic market stabilization during the 2007/8 world food price crisis. However, current literature says little about how these export restrictions interact with existing domestic support measures in jointly...... determining domestic market outcomes. This paper analyzes this interaction by providing a quantitative assessment on how increased spending on agricultural domestic support in China offset the negative effects on grain production caused by the country's export restrictions and how these two types of measures...

Feasibility of reactivity worth measurements by perturbation method with Caliban and Silene experimental reactors

Energy Technology Data Exchange (ETDEWEB)

Casoli, Pierre; Authier, Nicolas [Commissariat a l' Energie Atomique, Centre d' Etudes de Valduc, 21120 Is-Sur-Tille (France)

2008-07-01

Reactivity worth measurements of material samples put in the central cavities of nuclear reactors allow to test cross section nuclear databases or to extract information about the critical masses of fissile elements. Such experiments have already been completed on the Caliban and Silene experimental reactors operated by the Criticality and Neutronics Research Laboratory of Valduc (CEA, France) using the perturbation measurement technique. Calculations have been performed to prepare future experiments on new materials, such as light elements, structure materials, fission products or actinides. (authors)

Users’ Support as a Social Resource in Educational Services: Construct Validity and Measurement Invariance of the User-Initiated Support Scale (UISS)

Science.gov (United States)

Loera, Barbara; Martini, Mara; Viotti, Sara; Converso, Daniela

2016-01-01

Social support is an important resource for reducing the risks of stress and burnout at work. It seems to be particularly helpful for educational and social professionals. The constant and intense relationships with users that characterize this kind of service can be very demanding, increasing stress and leading to burnout. While significant attention has been paid to supervisors and colleagues in the literature, users have rarely been considered as possible sources of social support. The only exception is the Zimmermann et al.’s (2011) research, focused on customer support as a resource for workers’ well-being. This paper proposes the validation of the customer-initiated support scale developed by Zimmermann et al. (2011), translated into Italian and focused on educational services users (children’s parents), to measure the user support perceived by workers: the User-Initiated Support Scale (UISS). In Study 1 (105 teachers), which specifically involved educators and kindergarten teachers, the items and scale properties were preliminarily examined using descriptive analyses and exploratory factor analysis (EFA). In Study 2 (304 teachers), the construct and criterion validity and scale dimensionality were analyzed using confirmatory factor analysis (CFA). In Study 3 (304 teachers from Study 2 and 296 educators), measurement invariance (MI) was tested. The EFA results from Study 1 showed a one-factor solution (explained variance, 67.2%). The scale showed good internal coherence (alpha = 0.88). The CFA in Study 2 validated the one-factor solution (comparative fit index = 0.987; standardized root mean square residual = 0.054). Bivariate correlations confirmed construct validity; the UISS was positively associated (convergent) with user gratitude, and not associated (divergent) with disproportionate customer expectations. Regarding the criterion validity test, the UISS was strongly correlated with burnout and job satisfaction. The analysis of MI performed on the

Users' Support as a Social Resource in Educational Services: Construct Validity and Measurement Invariance of the User-Initiated Support Scale (UISS).

Science.gov (United States)

Loera, Barbara; Martini, Mara; Viotti, Sara; Converso, Daniela

2016-01-01

Social support is an important resource for reducing the risks of stress and burnout at work. It seems to be particularly helpful for educational and social professionals. The constant and intense relationships with users that characterize this kind of service can be very demanding, increasing stress and leading to burnout. While significant attention has been paid to supervisors and colleagues in the literature, users have rarely been considered as possible sources of social support. The only exception is the Zimmermann et al.'s (2011) research, focused on customer support as a resource for workers' well-being. This paper proposes the validation of the customer-initiated support scale developed by Zimmermann et al. (2011), translated into Italian and focused on educational services users (children's parents), to measure the user support perceived by workers: the User-Initiated Support Scale (UISS). In Study 1 (105 teachers), which specifically involved educators and kindergarten teachers, the items and scale properties were preliminarily examined using descriptive analyses and exploratory factor analysis (EFA). In Study 2 (304 teachers), the construct and criterion validity and scale dimensionality were analyzed using confirmatory factor analysis (CFA). In Study 3 (304 teachers from Study 2 and 296 educators), measurement invariance (MI) was tested. The EFA results from Study 1 showed a one-factor solution (explained variance, 67.2%). The scale showed good internal coherence (alpha = 0.88). The CFA in Study 2 validated the one-factor solution (comparative fit index = 0.987; standardized root mean square residual = 0.054). Bivariate correlations confirmed construct validity; the UISS was positively associated (convergent) with user gratitude, and not associated (divergent) with disproportionate customer expectations. Regarding the criterion validity test, the UISS was strongly correlated with burnout and job satisfaction. The analysis of MI performed on the Study 3

Optical waveguiding and applied photonics technological aspects, experimental issue approaches and measurements

CERN Document Server

Massaro, Alessandro

2012-01-01

Optoelectronics--technology based on applications light such as micro/nano quantum electronics, photonic devices, laser for measurements and detection--has become an important field of research. Many applications and physical problems concerning optoelectronics are analyzed in Optical Waveguiding and Applied Photonics.The book is organized in order to explain how to implement innovative sensors starting from basic physical principles. Applications such as cavity resonance, filtering, tactile sensors, robotic sensor, oil spill detection, small antennas and experimental setups using lasers are a

Measurement of ultra-high energy cosmic rays: An experimental summary and prospects

Directory of Open Access Journals (Sweden)

Fukushima M.

2013-06-01

Full Text Available Measurements of Ultra-High Energy Cosmic Rays achieved remarkable progress in the last 10 years. Physicists, gathered from around the world in the symposium UHECR-2012 held at CERN on February 13-16 2012, reported their most up-to-date observations, discussed the meaning of their findings, and identified remaining problems and future challenges in this field. This paper is a part of the symposium proceedings on the experimental summary and future prospects of the UHECR study.

Neutronics model of the bulk shielding reactor (BSR): validation by comparison of calculations with the experimental measurements

International Nuclear Information System (INIS)

Johnson, J.O.; Miller, L.F.; Kam, F.B.K.

1981-05-01

A neutronics model for the Oak Ridge National Laboratory Bulk Shielding Reactor (ORNL-SAR) was developed and verified by experimental measurements. A cross-section library was generated from the 218 group Master Library using the AMPX Block Code system. A series of one-, two-, and three-dimensional neutronics calculations were performed utilizing both transport and diffusion theory. Spectral comparison was made with 58 Ni(n,p) reaction. The results of the comparison between the calculational model and other experimental measurements showed agreement within 10% and therefore the model was determined to be adequate for calculating the neutron fluence for future irradiation experiments in the ORNL-BSR

Neutronics model of the bulk shielding reactor (BSR): validation by comparison of calculations with the experimental measurements

Energy Technology Data Exchange (ETDEWEB)

Johnson, J.O.; Miller, L.F.; Kam, F.B.K.

1981-05-01

A neutronics model for the Oak Ridge National Laboratory Bulk Shielding Reactor (ORNL-SAR) was developed and verified by experimental measurements. A cross-section library was generated from the 218 group Master Library using the AMPX Block Code system. A series of one-, two-, and three-dimensional neutronics calculations were performed utilizing both transport and diffusion theory. Spectral comparison was made with /sup 58/Ni(n,p) reaction. The results of the comparison between the calculational model and other experimental measurements showed agreement within 10% and therefore the model was determined to be adequate for calculating the neutron fluence for future irradiation experiments in the ORNL-BSR.

Experimental assessment for instantaneous temperature and heat flux measurements under Diesel motored engine conditions

International Nuclear Information System (INIS)

Torregrosa, A.J.; Bermúdez, V.; Olmeda, P.; Fygueroa, O.

2012-01-01

Higlights: ► We measured in-cylinder wall heat fluxes. ► We examine the effects of different engine parameters. ► Increasing air mass flow increase heat fluxes. ► The effect of engine speed can be masked by the effect of volumetric efficiency. ► Differences among the different walls have been found. - Abstract: The main goal of this work is to validate an innovative experimental facility and to establish a methodology to evaluate the influence of some of the engine parameters on local engine heat transfer behaviour under motored steady-state conditions. Instantaneous temperature measurements have been performed in order to estimate heat fluxes on a modified Diesel single cylinder combustion chamber. This study was divided into two main parts. The first one was the design and setting on of an experimental bench to reproduce Diesel conditions and perform local-instantaneous temperature measurements along the walls of the combustion chamber by means of fast response thermocouples. The second one was the development of a procedure for temperature signal treatment and local heat flux calculation based on one-dimensional Fourier analysis. A thermodynamic diagnosis model has been employed to characterise the modified engine with the new designed chamber. As a result of the measured data coherent findings have been obtained in order to understand local behaviour of heat transfer in an internal combustion engine, and the influence of engine parameters on local instantaneous temperature and heat flux, have been analysed.

An experimental applications of impedance measurements by spectral analysis to electrochemistry and corrosion

International Nuclear Information System (INIS)

Castro, E.B.; Vilche, J.R.; Milocco, R.H.

1984-01-01

An impedance measurement system based on the spectral analysis of excitation and response signals was implemented using a pseudo-random binary sequence in the generation of the electrical perturbation signal. The spectral density functions were estimated through finite Fourier transforms of the original time history records by fast computation of Fourier series. Experimental results obtained using the FFT algorithm in the developed impedance measurement system which covers a wide frequency range, 10 KHz >= f >= 1 mHz, are given both for dummy cells representing conventional electric circuits in electrochemistry and corrosion systems and for the Fe/acidic chloride solution interfaces under different polarization conditions. (C.L.B.) [pt

Experimental testing facilities for ultrasonic measurements in heavy liquid metal

International Nuclear Information System (INIS)

Cojocaru, V.; Ionescu, V.; Nicolescu, D.; Nitu, A.

2016-01-01

The thermo-physical properties of Heavy Liquid Metals (HLM), like lead or its alloy, Lead Bismuth Eutectic (LBE), makes them attractive as coolant candidates in advanced nuclear systems. The opaqueness, that is common to all liquid metals, disables all optical methods. For this reason ultrasound waves are used in different applications in heavy liquid metal technology, for example for flow and velocity measurements and for inspection techniques. The practical use of ultrasound in heavy liquid metals still needs to be demonstrated by experiments. This goal requires heavy liquid metal technology facility especially adapted to this task. In this paper is presented an experimental testing facility for investigations of Heavy Liquid Metals acoustic properties, designed and constructed in RATEN ICN. (authors)

Experimental hint for gravitational CP violation

Energy Technology Data Exchange (ETDEWEB)

Gharibyan, Vahagn [Deutsches Elektronen-Synchrotron, Hamburg (Germany). MDI Group

2016-01-15

An equality of particle and antiparticle gravitational interactions holds in general relativity and is supported by indirect observations. Gravity dependence on rotation or spin direction is experimentally constrained only at low energies. Here a method based on high energy Compton scattering is developed to measure the gravitational interaction of accelerated charged particles. Within that formalism the Compton spectra measured at HERA rule out the positron's anti-gravity and hint for a gravitational CP violation around 13 GeV energies, at a maximal level of 1.3±0.2% for the charge and 0.68±0.09% for the space parity. A stronger gravitational coupling to left helicity electrons relative to right helicity positrons is detected.

Experimental hint for gravitational CP violation

International Nuclear Information System (INIS)

Gharibyan, Vahagn

2016-01-01

An equality of particle and antiparticle gravitational interactions holds in general relativity and is supported by indirect observations. Gravity dependence on rotation or spin direction is experimentally constrained only at low energies. Here a method based on high energy Compton scattering is developed to measure the gravitational interaction of accelerated charged particles. Within that formalism the Compton spectra measured at HERA rule out the positron's anti-gravity and hint for a gravitational CP violation around 13 GeV energies, at a maximal level of 1.3±0.2% for the charge and 0.68±0.09% for the space parity. A stronger gravitational coupling to left helicity electrons relative to right helicity positrons is detected.

Fuel rod-to-support contact pressure and stress measurement for CHASNUPP-1(PWR) fuel

International Nuclear Information System (INIS)

Waseem; Elahi, N.; Siddiqui, A.; Murtaza, G.

2011-01-01

Research highlights: → A detailed finite element model of spacer grid cell with fuel rod-to-support has been developed to determine the contact pressure between the supports of the grid and fuel rod cladding. → The spring hold-down force is calculated using the contact pressure obtained from the FE model. → Experiment has also been conducted in the same environment for the measurement of this force. → The spring hold-down force values obtained from both studies confirm the validation of this analysis. → The stress obtained through this analysis is less than the yield strength of spacer grid material, thus fulfils the structural integrity criteria of grid. - Abstract: This analysis has been made in an attempt to measure the contact pressure of the PWR fuel assembly spacer grid spring and to verify its structural integrity at room temperature in air. A detailed finite element (FE) model of spacer grid cell with fuel rod-to-support has been developed to determine the contact pressure between the supports of the grid and fuel rod cladding. The FE model of a fuel rod-to-support system is produced with shell and contact elements. The spring hold-down force is calculated using the contact pressure obtained from the FE model. Experiment has also been conducted in the same environment for the measurement of this force. The spring hold-down force values obtained from both studies are compared, which show good agreement, and in turn confirm the validation of this analysis. The Stress obtained through this analysis is less than the yield strength of spacer grid material (Inconel-718), thus fulfils the structural integrity criteria of grid.

Fuel rod-to-support contact pressure and stress measurement for CHASNUPP-1(PWR) fuel

Energy Technology Data Exchange (ETDEWEB)

Waseem, E-mail: wazim_me@hotmail.co [Directorate General Nuclear Power Fuel, Pakistan Atomic Energy Commission, P.O. Box No. 1847, Islamabad 44000 (Pakistan); Elahi, N.; Siddiqui, A.; Murtaza, G. [Directorate General Nuclear Power Fuel, Pakistan Atomic Energy Commission, P.O. Box No. 1847, Islamabad 44000 (Pakistan)

2011-01-15

Research highlights: A detailed finite element model of spacer grid cell with fuel rod-to-support has been developed to determine the contact pressure between the supports of the grid and fuel rod cladding. The spring hold-down force is calculated using the contact pressure obtained from the FE model. Experiment has also been conducted in the same environment for the measurement of this force. The spring hold-down force values obtained from both studies confirm the validation of this analysis. The stress obtained through this analysis is less than the yield strength of spacer grid material, thus fulfils the structural integrity criteria of grid. - Abstract: This analysis has been made in an attempt to measure the contact pressure of the PWR fuel assembly spacer grid spring and to verify its structural integrity at room temperature in air. A detailed finite element (FE) model of spacer grid cell with fuel rod-to-support has been developed to determine the contact pressure between the supports of the grid and fuel rod cladding. The FE model of a fuel rod-to-support system is produced with shell and contact elements. The spring hold-down force is calculated using the contact pressure obtained from the FE model. Experiment has also been conducted in the same environment for the measurement of this force. The spring hold-down force values obtained from both studies are compared, which show good agreement, and in turn confirm the validation of this analysis. The Stress obtained through this analysis is less than the yield strength of spacer grid material (Inconel-718), thus fulfils the structural integrity criteria of grid.

Measurement of cerebral white matter perfusion using pseudocontinuous arterial spin labeling 3T magnetic resonance imaging--an experimental and theoretical investigation of feasibility.

Directory of Open Access Journals (Sweden)

Wen-Chau Wu

Full Text Available PURPOSE: This study was aimed to experimentally and numerically investigate the feasibility of measuring cerebral white matter perfusion using pseudocontinuous arterial spin labeling (PCASL 3T magnetic resonance imaging (MRI at a relatively fine resolution to mitigate partial volume effect from gray matter. MATERIALS AND METHODS: The Institutional Research Ethics Committee approved this study. On a clinical 3T MR system, ten healthy volunteers (5 females, 5 males, age = 28 ± 3 years were scanned after providing written informed consent. PCASL imaging was performed with varied combinations of labeling duration (τ = 1000, 1500, 2000, and 2500 ms and post-labeling delay (PLD = 1000, 1400, 1800, and 2200 ms, at a spatial resolution (1.56 x 1.56 x 5 mm(3 finer than commonly used (3.5 x 3.5 mm(2, 5-8 mm in thickness. Computer simulations were performed to calculate the achievable perfusion-weighted signal-to-noise ratio at varied τ, PLD, and transit delay. RESULTS: Based on experimental and numerical data, the optimal τ and PLD were found to be 2000 ms and 1500-1800 ms, respectively, yielding adequate SNR (~2 to support perfusion measurement in the majority (~60% of white matter. The measurement variability was about 9% in a one-week interval. The measured white matter perfusion and perfusion ratio of gray matter to white matter were 15.8-27.5 ml/100ml/min and 1.8-4.0, respectively, depending on spatial resolution as well as the amount of deep white matter included. CONCLUSION: PCASL 3T MRI is able to measure perfusion in the majority of cerebral white matter at an adequate signal-to-noise ratio by using appropriate tagging duration and post-labeling delay. Although pixel-wise comparison may not be possible, region-of-interest based flow quantification is feasible.

Socioeconomic Status, Structural and Functional Measures of Social Support, and Mortality

Science.gov (United States)

Stringhini, Silvia; Berkman, Lisa; Dugravot, Aline; Ferrie, Jane E.; Marmot, Michael; Kivimaki, Mika; Singh-Manoux, Archana

2012-01-01

The authors examined the associations of social support with socioeconomic status (SES) and with mortality, as well as how SES differences in social support might account for SES differences in mortality. Analyses were based on 9,333 participants from the British Whitehall II Study cohort, a longitudinal cohort established in 1985 among London-based civil servants who were 35–55 years of age at baseline. SES was assessed using participant's employment grades at baseline. Social support was assessed 3 times in the 24.4-year period during which participants were monitored for death. In men, marital status, and to a lesser extent network score (but not low perceived support or high negative aspects of close relationships), predicted both all-cause and cardiovascular mortality. Measures of social support were not associated with cancer mortality. Men in the lowest SES category had an increased risk of death compared with those in the highest category (for all-cause mortality, hazard ratio = 1.59, 95% confidence interval: 1.21, 2.08; for cardiovascular mortality, hazard ratio = 2.48, 95% confidence interval: 1.55, 3.92). Network score and marital status combined explained 27% (95% confidence interval: 14, 43) and 29% (95% confidence interval: 17, 52) of the associations between SES and all-cause and cardiovascular mortality, respectively. In women, there was no consistent association between social support indicators and mortality. The present study suggests that in men, social isolation is not only an important risk factor for mortality but is also likely to contribute to differences in mortality by SES. PMID:22534202

Biomechanical evaluation of heel elevation on load transfer — experimental measurement and finite element analysis

Science.gov (United States)

Luximon, Yan; Luximon, Ameersing; Yu, Jia; Zhang, Ming

2012-02-01

In spite of ill-effects of high heel shoes, they are widely used for women. Hence, it is essential to understand the load transfer biomechanics in order to design better fit and comfortable shoes. In this study, both experimental measurement and finite element analysis were used to evaluate the biomechanical effects of heel height on foot load transfer. A controlled experiment was conducted using custom-designed platforms. Under different weight-bearing conditions, peak plantar pressure, contact area and center of pressure were analyzed. A three-dimensional finite element foot model was used to simulate the high-heel support and to predict the internal stress distributions and deformations for different heel heights. Results from both experiment and model indicated that heel elevations had significant effects on all variables. When heel elevation increased, the center of pressure shifted from the midfoot region to the forefoot region, the contact area was reduced by 26% from 0 to 10.2 cm heel and the internal stress of foot bones increased. Prediction results also showed that the strain and total tension force of plantar fascia was minimum at 5.1 cm heel condition. This study helps to better understand the biomechanical behavior of foot, and to provide better suggestions for design parameters of high heeled shoes.

Exploring Shared Measurement Properties and Score Comparability between Two Versions of the "Supports Intensity Scale"

Science.gov (United States)

Seo, Hyojeong; Shogren, Karrie A.; Wehmeyer, Michael L.; Hughes, Carolyn; Thompson, James R.; Little, Todd D.; Palmer, Susan B.

2016-01-01

This study examined similarities and differences in measurement properties and score comparability of the "Supports Intensity Scale-Adult Version" (16-64 years) and the "Supports Intensity Scale-Children's Version" (5-16 years). Data were collected from 142 adolescents with intellectual disability with both versions of the…

The experimental Balzac program at Masurca in support of the design of Super Phenix 2

International Nuclear Information System (INIS)

Sztark, H.; d'Angelo, A.; Soule, R.; Granget, G.

1986-09-01

The Balzac experimental program, performed in the Masurca critical assembly at Cadarache since 1985, is designed for the validation of the neutron physics requirements related to the physical options of the SPX2 project. Geometrically simple configurations are chosen in which parameters, typical for those physical options, are varied in a systematic manner while the basic fissile composition is kept the same. Measurements will be made especially of the critical mass, the distributions of reaction rates, spectral indices, 10 B(n,α) reaction and gamma-ray heating in particular in the control-rod and in internal storage regions. Reactivity effects of (UPu)O 2 isotopic composition variations and of different control-rod absorber configurations will be also measured using the MSM technique

Experimental plasma research project summaries

International Nuclear Information System (INIS)

1978-08-01

This report contans descriptions of the activities supported by the Experimental Plasma Research Branch of APP. The individual project summaries were prepared by the principal investigators and include objectives and milestones for each project. The projects are arranged in six research categories: Plasma Properties; Plasma Heating; Plasma Measurements and Instrumentation; Atomic, Molecular and Nuclear Physics; Advanced Superconducting Materials; and the Fusion Plasma Research Facility (FPRF). Each category is introduced with a statement of objectives and recent progress and followed by descriptions of individual projects. An overall budget summary is provided at the beginning of the report

Fuel performance evaluation for the CAFE experimental device

International Nuclear Information System (INIS)

Giovedi, Claudia; Hirota, Leandro T.

2011-01-01

Fuel rod cladding material is the second barrier to prevent the release of radioactive inventories in a PWR reactor. In this sense, an important safety aspect is to assess the fuel behavior under operational conditions. This can be made by means of fuel performance codes and confirmed by experimental measurements. In order to evaluate the fuel behavior of fuel rods in steady-state conditions, it was designed an experimental irradiation device, the Nuclear Fuel Irradiation Circuit (CAFE-Mod1). This device will allow controlling the surface rod temperature, to measure the power associated to the rod and the evolution of fission gas release for a typical PWR fuel pin. However, to support the experimental irradiation program, it is extremely important to simulate the experimental conditions using a fuel performance code. The aim of this paper is to evaluate some parameters and aspects related to the fuel rod behavior during the irradiation program. This evaluation was carried out by means of an adapted fuel performance code. Obtained results have shown that besides of the variation observed for parameters, such as, fuel temperature and fission gas release as a function of fuel enrichment level, the fuel rod integrity was preserved in all studied conditions. (author)

Experimental measurement of 12C+16O fusion at stellar energies

Science.gov (United States)

Fang, X.; Tan, W. P.; Beard, M.; deBoer, R. J.; Gilardy, G.; Jung, H.; Liu, Q.; Lyons, S.; Robertson, D.; Setoodehnia, K.; Seymour, C.; Stech, E.; Vande Kolk, B.; Wiescher, M.; deSouza, R. T.; Hudan, S.; Singh, V.; Tang, X. D.; Uberseder, E.

2017-10-01

The total cross section of the 12C+16O fusion reaction has been measured at low energies to investigate the role of this reaction during late stellar evolution burning phases. A high-intensity oxygen beam, produced by the 5 MV pelletron accelerator at the University of Notre Dame, impinged on a thick, ultrapure graphite target. Protons and γ rays were simultaneously measured in the center-of-mass energy range from 3.64 to 5.01 MeV for singles and from 3.73 to 4.84 MeV for coincidence events, using silicon and Ge detectors. Statistical model calculations were employed to interpret the experimental results. The emergence of a new resonance-like broad structure and a decreasing trend in the S -factor data towards lower energies (opposite to previous data) are found for the 12C+16O fusion reaction. Based on these results the uncertainty range of the reaction rate within the temperature range of late stellar burning environments is discussed.

Experimental measurements of competition between fundamental and second harmonic emission in a quasi-optical gyrotron

International Nuclear Information System (INIS)

Alberti, S.; Pedrozzi, M.; Tran, M.Q.; Hogge, J.P.; Tran, T.M.; Muggli, P.; Joedicke, B.; Mathews, H.G.

1990-04-01

A quasi-optical gyrotron (QOG) designed for operation at the fundamental (Ω ce ≅100 GHz) exhibits simultaneous emission at Ω ce and 2Ω ce (second harmonic). For a beam current of 4 A, 20% of the total RF power is emitted at the second harmonic. The experimental measurements show that the excitation of the second harmonic is only possible when the fundamental is present. The frequency of the second harmonic is locked by the frequency of the fundamental. Experimental evidence shows that when the second harmonic is not excited, total efficiency is enhanced. (author) 6 refs., 5 figs., 1 tab

Measuring and Advancing Experimental Design Ability in an Introductory Course without Altering Existing Lab Curriculum

Directory of Open Access Journals (Sweden)

Ryan A. Shanks

2017-05-01

Full Text Available Introductory biology courses provide an important opportunity to prepare students for future courses, yet existing cookbook labs, although important in their own way, fail to provide many of the advantages of semester-long research experiences. Engaging, authentic research experiences aid biology students in meeting many learning goals. Therefore, overlaying a research experience onto the existing lab structure allows faculty to overcome barriers involving curricular change. Here we propose a working model for this overlay design in an introductory biology course and detail a means to conduct this lab with minimal increases in student and faculty workloads. Furthermore, we conducted exploratory factor analysis of the Experimental Design Ability Test (EDAT and uncovered two latent factors which provide valid means to assess this overlay model’s ability to increase advanced experimental design abilities. In a pre-test/post-test design, we demonstrate significant increases in both basic and advanced experimental design abilities in an experimental and comparison group. We measured significantly higher gains in advanced experimental design understanding in students in the experimental group. We believe this overlay model and EDAT factor analysis contribute a novel means to conduct and assess the effectiveness of authentic research experiences in an introductory course without major changes to the course curriculum and with minimal increases in faculty and student workloads.

Calibration of uncertain inputs to computer models using experimentally measured quantities and the BMARS emulator

International Nuclear Information System (INIS)

Stripling, H.F.; McClarren, R.G.; Kuranz, C.C.; Grosskopf, M.J.; Rutter, E.; Torralva, B.R.

2011-01-01

We present a method for calibrating the uncertain inputs to a computer model using available experimental data. The goal of the procedure is to produce posterior distributions of the uncertain inputs such that when samples from the posteriors are used as inputs to future model runs, the model is more likely to replicate (or predict) the experimental response. The calibration is performed by sampling the space of the uncertain inputs, using the computer model (or, more likely, an emulator for the computer model) to assign weights to the samples, and applying the weights to produce the posterior distributions and generate predictions of new experiments within confidence bounds. The method is similar to the Markov chain Monte Carlo (MCMC) calibration methods with independent sampling with the exception that we generate samples beforehand and replace the candidate acceptance routine with a weighting scheme. We apply our method to the calibration of a Hyades 2D model of laser energy deposition in beryllium. We employ a Bayesian Multivariate Adaptive Regression Splines (BMARS) emulator as a surrogate for Hyades 2D. We treat a range of uncertainties in our system, including uncertainties in the experimental inputs, experimental measurement error, and systematic experimental timing errors. The results of the calibration are posterior distributions that both agree with intuition and improve the accuracy and decrease the uncertainty in experimental predictions. (author)

WISE: Automated support for software project management and measurement. M.S. Thesis

Science.gov (United States)

Ramakrishnan, Sudhakar

1995-01-01

One important aspect of software development and IV&V is measurement. Unless a software development effort is measured in some way, it is difficult to judge the effectiveness of current efforts and predict future performances. Collection of metrics and adherence to a process are difficult tasks in a software project. Change activity is a powerful indicator of project status. Automated systems that can handle change requests, issues, and other process documents provide an excellent platform for tracking the status of the project. A World Wide Web based architecture is developed for (a) making metrics collection an implicit part of the software process, (b) providing metric analysis dynamically, (c) supporting automated tools that can complement current practices of in-process improvement, and (d) overcoming geographical barrier. An operational system (WISE) instantiates this architecture allowing for the improvement of software process in a realistic environment. The tool tracks issues in software development process, provides informal communication between the users with different roles, supports to-do lists (TDL), and helps in software process improvement. WISE minimizes the time devoted to metrics collection, analysis, and captures software change data. Automated tools like WISE focus on understanding and managing the software process. The goal is improvement through measurement.

Measurements of gamma-ray energy deposition in a heterogeneous reactor experimental configuration and their analysis

International Nuclear Information System (INIS)

Calamand, D.; Wouters, R. de; Knipe, A.D.; Menil, R.

1984-10-01

An important contribution to the power output of a fast reactor is provided by the energy deposition from gamma-rays, and is particularly significant in the inner fertile zones of heterogeneous breeder reactor designs. To establish the validity of calculational methods and data for such systems an extensive series of measurements was performed in the zero power reactor Masurca, as part of the RACINE programme. The experimental study involved four European laboratories and the measurement techniques covered a range of thermoluminescent dosemeters and an ionization chamber. The present paper describes and compares the gamma-ray energy deposition measurements and analysis

Neutron spectrometer for DD/DT burning ratio measurement in fusion experimental reactor

International Nuclear Information System (INIS)

Asai, Keisuke; Naoi, Norihiro; Iguchi, Tetsuo; Watanabe, Kenichi; Kawarabayashi, Jun; Nishitani, Takeo

2006-01-01

The most feasible fuels for a fusion reactor are D (Deuterium) and T (Tritium). DD and/or DT fusion reaction or nuclear burning reaction provides two kinds of neutrons, DD neutron and DT neutron, respectively. DD/DT burning ratio, which can be estimated by DD/DT neutron ratio in the burning plasma, is essential for burn control, alpha particle emission rate monitoring and tritium fuel cycle estimation. Here we propose a new neutron spectrometer for the absolute DD/DT burning ratio measurement. The system consists of a Proton Recoil Telescope (PRT) and a Time-of-Flight (TOF) technique. We have conducted preliminary experiments with a prototype detector and a DT neutron beam (φ20 mm) at the Fusion Neutronics Source, Japan Atomic Energy Agency (JAEA), to assess its basic performance. The detection efficiency obtained by the experiment is consistent with the calculation results in PRT, and sufficient energy resolution for the DD/DT neutron discrimination has been achieved in PRT and TOF. The validity of the Monte Carlo calculation has also been confirmed by comparing the experimental results with the calculation results. The design consideration of this system for use in ITER (International Thermonuclear Experimental Reactor) has shown that this system is capable of monitoring the line-integrated DD/DT burning ratio for the plasma core line of sight with the required measurement accuracy of 20% in the upper 4 decades of the ITER operation (fusion power: 100 kW-700 MW). (author)

Experimental arrangement to measure dispersion in optical fiber devices

International Nuclear Information System (INIS)

Armas Rivera, Ivan; Beltran Perez, Georgina; Castillo Mixcoatl, Juan; Munoz Aguirre, Severino; Zaca Moran, Placido

2011-01-01

Dispersion is a quite important parameter in systems based on optical fiber, especially in pulsed emission lasers, where the temporal width is affected by such parameter. Therefore, it is necessary to consider the dispersion provoked by each component in the cavity. There are various experimental interferometric arrangements to evaluate this parameter. Generally, these systems modify the wavelength to obtain information about the n(λ) dependency, which is contained in the interferogram phase. However, this makes the system quite slow and it requires tunable and narrow bandwidth laser sources. In the present work, results obtained from an arrangement based on Mach-Zehnder interferometer where one of the arms is the optical fiber under study, while the reference one is air, are presented. In order to determine the n(λ) dependency, a wide spectrum light source was used in the wavelength range of interest. The phase information was evaluated from the interferometric signal measured by an optical spectrum analyzer.

Experimental arrangement to measure dispersion in optical fiber devices

Energy Technology Data Exchange (ETDEWEB)

Armas Rivera, Ivan [Benemerita Universidad Autonoma de Puebla, Facultad de Ciencias de la Electronica (Mexico); Beltran Perez, Georgina; Castillo Mixcoatl, Juan; Munoz Aguirre, Severino [Benemerita Universidad Autonoma de Puebla, Facultad de Ciencias Fisico Matematicas (Mexico); Zaca Moran, Placido, E-mail: ivan_rr1@hotmail.com [Benemerita Universidad Autonoma de Puebla, Fisicoquimica de Materiales ICUAP (Mexico)

2011-01-01

Dispersion is a quite important parameter in systems based on optical fiber, especially in pulsed emission lasers, where the temporal width is affected by such parameter. Therefore, it is necessary to consider the dispersion provoked by each component in the cavity. There are various experimental interferometric arrangements to evaluate this parameter. Generally, these systems modify the wavelength to obtain information about the n({lambda}) dependency, which is contained in the interferogram phase. However, this makes the system quite slow and it requires tunable and narrow bandwidth laser sources. In the present work, results obtained from an arrangement based on Mach-Zehnder interferometer where one of the arms is the optical fiber under study, while the reference one is air, are presented. In order to determine the n({lambda}) dependency, a wide spectrum light source was used in the wavelength range of interest. The phase information was evaluated from the interferometric signal measured by an optical spectrum analyzer.

Keeping the Spirits Up: The Effect of Teachers' and Parents' Emotional Support on Children's Working Memory Performance.

Science.gov (United States)

Vandenbroucke, Loren; Spilt, Jantine; Verschueren, Karine; Baeyens, Dieter

2017-01-01

Working memory, used to temporarily store and mentally manipulate information, is important for children's learning. It is therefore valuable to understand which (contextual) factors promote or hinder working memory performance. Recent research shows positive associations between positive parent-child and teacher-student interactions and working memory performance and development. However, no study has yet experimentally investigated how parents and teachers affect working memory performance. Based on attachment theory, the current study investigated the role of parent and teacher emotional support in promoting working memory performance by buffering the negative effect of social stress. Questionnaires and an experimental session were completed by 170 children from grade 1 to 2 ( M age = 7 years 6 months, SD = 7 months). Questionnaires were used to assess children's perceptions of the teacher-student and parent-child relationship. During an experimental session, working memory was measured with the Corsi task backward (Milner, 1971) in a pre- and post-test design. In-between the tests stress was induced in the children using the Cyberball paradigm (Williams et al., 2000). Emotional support was manipulated (between-subjects) through an audio message (either a weather report, a supportive message of a stranger, a supportive message of a parent, or a supportive message of a teacher). Results of repeated measures ANOVA showed no clear effect of the stress induction. Nevertheless, an effect of parent and teacher support was found and depended on the quality of the parent-child relationship. When children had a positive relationship with their parent, support of parents and teachers had little effect on working memory performance. When children had a negative relationship with their parent, a supportive message of that parent decreased working memory performance, while a supportive message from the teacher increased performance. In sum, the current study suggests that

Experimental density and viscosity measurements of di(2ethylhexyl)sebacate at high pressure

International Nuclear Information System (INIS)

Paredes, Xavier; Fandino, Olivia; Pensado, Alfonso S.; Comunas, Maria J.P.; Fernandez, Josefa

2012-01-01

Highlights: → We measure viscosities for di(2-ethylhexyl)sebacate from (298.15 to 398.15) K and up to 60 MPa. → We measure densities for DEHS from (298.15 to 373.15) K and from (0.1 to 60) MPa. → The reported and lit. data were used in a viscosity correlation from (273 to 491) K and up to 1.1 GPa. → This correlation could be used in industrial equipment that operate at high pressures. - Abstract: Experimental densities and dynamic viscosities of di(2-ethylhexyl)sebacate (DEHS) are the object of study in this work. DEHS could be a useful industrial reference fluid for moderately high viscosity at high pressures as it is often used as a pressure transmitting fluid. At atmospheric pressure the density and viscosity measurements have been performed in a rotational SVM 3000 Stabinger viscometer from (273.15 to 373.15) K, whereas from (0.1 to 60) MPa and from (298.15 to 398.15) K an automated Anton Paar DMA HPM vibrating-tube densimeter, and a high-pressure rolling-ball viscometer were used. Several Vogel-Fulcher-Tammann type equations were used to fit the experimental values of viscosity to the pressure and temperature. The measured viscosity data have been used together with previous data found in the literature to establish a correlation of the viscosity surface η(T, p) of DEHS, covering a temperature range from (273 to 491) K and pressure up to 1.1 GPa. This correlation could be used in industrial equipment like viscometers and other devices that operate at high pressures. Our viscosity data have also been fitted as a function of temperature and volume to the thermodynamic scaling model of Roland et al. [C.M. Roland, S. Bair, R. Casalini, J. Chem. Phys. 125 (2006) 124508].

Experimental validation of the buildings energy performance (PEC assessment methods with reference to occupied spaces heating

Directory of Open Access Journals (Sweden)

Cristian PETCU

2010-01-01

Full Text Available This paper is part of the series of pre-standardization research aimed to analyze the existing methods of calculating the Buildings Energy Performance (PEC in view of their correction of completing. The entire research activity aims to experimentally validate the PEC Calculation Algorithm as well as the comparative application, on the support of several case studies focused on representative buildings of the stock of buildings in Romania, of the PEC calculation methodology for buildings equipped with occupied spaces heating systems. The targets of the report are the experimental testing of the calculation models so far known (NP 048-2000, Mc 001-2006, SR EN 13790:2009, on the support provided by the CE INCERC Bucharest experimental building, together with the complex calculation algorithms specific to the dynamic modeling, for the evaluation of the occupied spaces heat demand in the cold season, specific to the traditional buildings and to modern buildings equipped with solar radiation passive systems, of the ventilated solar space type. The schedule of the measurements performed in the 2008-2009 cold season is presented as well as the primary processing of the measured data and the experimental validation of the heat demand monthly calculation methods, on the support of CE INCERC Bucharest. The calculation error per heating season (153 days of measurements between the measured heat demand and the calculated one was of 0.61%, an exceptional value confirming the phenomenological nature of the INCERC method, NP 048-2006. The mathematical model specific to the hourly thermal balance is recurrent – decisional with alternating paces. The experimental validation of the theoretical model is based on the measurements performed on the CE INCERC Bucharest building, within a time lag of 57 days (06.01-04.03.2009. The measurements performed on the CE INCERC Bucharest building confirm the accuracy of the hourly calculation model by comparison to the values

Experimental measurements and theoretical simulations for neutron flux in self-serve facility of Dhruva reactor

International Nuclear Information System (INIS)

Rana, Y.S.; Mishra, Abhishek; Singh, Tej

2016-06-01

Dhruva is a 100 MW th tank type research reactor with natural metallic uranium as fuel and heavy water as coolant, moderator and reflector. The reactor is utilized for production of a large variety of radioisotopes for fulfilling growing demands of various applications in industrial, agricultural and medicinal sectors, and neutron beam research in condensed matter physics. The core consists of two on-power tray rods for radioisotope production and fifteen experimental beam holes for neutron beam research. Recently, a self-serve facility has also been commissioned in one of the through tubes in the reactor for carrying out short term irradiations. To get accurate information about neutron flux spectrum, measurements have been carried out in self-serve facility of Dhruva reactor. The present report describes measurement method, analysis technique and results. Theoretical estimations for neutron flux were also carried out and a comparison between theoretical and experimental results is made. (author)

M and S supporting unmanned autonomous systems (UAxS) concept development and experimentation

Science.gov (United States)

Biagini, Marco; Scaccianoce, Alfio; Corona, Fabio; Forconi, Sonia; Byrum, Frank; Fowler, Olivia; Sidoran, James L.

2017-05-01

The development of the next generation of multi-domain unmanned semi and fully autonomous C4ISR systems involves a multitude of security concerns and interoperability challenges. Conceptual solutions to capability shortfalls and gaps can be identified through Concept Development and Experimentation (CD and E) cycles. Modelling and Simulation (M and S) is a key tool in supporting unmanned autonomous systems (UAxS) CD and E activities and addressing associated security challenges. This paper serves to illustrate the application of M and S to UAxS development and highlight initiatives made by the North Atlantic Treaty Organization (NATO) M and S Centre of Excellence (CoE) to facilitate interoperability. The NATO M and S CoE collaborates with other NATO and Nations bodies in order to develop UAxS projects such as the Allied Command for Transformation Counter Unmanned Autonomous Systems (CUAxS) project or the work of Science and Technology Organization (STO) panels. Some initiatives, such as Simulated Interactive Robotics Initiative (SIRI) made the baseline for further developments and to study emerging technologies in M and S and robotics fields. Artificial Intelligence algorithm modelling, Robot Operating Systems (ROS), network operations, cyber security, interoperable languages and related data models are some of the main aspects considered in this paper. In particular, the implementation of interoperable languages like C-BML and NIEM MilOps are discussed in relation to a Command and Control - Simulation Interoperability (C2SIM) paradigm. All these technologies are used to build a conceptual architecture to support UAxS CD and E.In addition, other projects that the NATO M and S CoE is involved in, such as the NATO Urbanization Project could provide credible future operational environments and benefit UAxS project development, as dual application of UAxS technology in large urbanized areas.In conclusion, this paper contains a detailed overview regarding how applying

A measurement of cosmic-ray LET-spectra using a microprocessor supported microscope

International Nuclear Information System (INIS)

Beer, J.; Heinrich, W.

1982-01-01

A microprocessor supported semi-automatic system for measurements of nuclear tracks in plastic detectors is presented. It consists of a microscope and a stepping motor driven stage. A Motorola microprocessor MC 6800 controls the measurement. It accepts the co-ordinates of the stage as well as the position of the focus and computes cone length and dip angle from the three-dimensional co-ordinates. LET-spectra were measured from two cellulose nitrate foils of the Biostack III experiment flown with the Apollo-Soyus-Test-Project in 1975. One of these foils was shielded by 3 g/cm 2 and the other one by 15 g/cm 2 . The two spectra show no statistically significant decrease of intensity. (author)

How carryover has an effect on recovery measures related to the area under the curve: theoretical and experimental investigations using cardiovascular parameters.

Science.gov (United States)

Sawada, Yukihiro; Kato, Yuichi

2011-03-01

This study examines cardiovascular recovery from mental stress. Investigating the absence or presence of carryover effect, the effect of the final reactivity observed at the end of stressful task on the successive recovery, was the major objective. A recently advocated recovery measure related to the area under the curve, mean recovery rate (MRR), was investigated, comparing with the two relatives of this type, total carryover (TCO) and literally area under the curve (AUC). At the onset, a detailed theoretical formulation of each measure was carried out, starting from its original definition. It was predicted that MRR, but not TCO or AUC, could be free from the carryover effect. Next, 88 male students underwent a 5-min mental arithmetic during which blood pressure and heart rate were measured. Nearly all the theoretical predictions (i.e., 5/6 for the three recovery measures by two cardiovascular parameters) were supported by experimental data. There was only one exception: for heart rate, there was a proportional relationship even for MRR versus the final reactivity. Vagal rebound in the recovery period was conceived as the main contributor of this contradiction. The implications of these results for the understanding of future directions in recovery studies are discussed.

Environmental dose rate heterogeneity of beta radiation and its implications for luminescence dating: Monte Carlo modelling and experimental validation

DEFF Research Database (Denmark)

Nathan, R.P.; Thomas, P.J.; Jain, M.

2003-01-01

and identify the likely size of these effects on D-e distributions. The study employs the MCNP 4C Monte Carlo electron/photon transport model, supported by an experimental validation of the code in several case studies. We find good agreement between the experimental measurements and the Monte Carlo...

Experimental test of far-infrared polarimetry for Faraday rotation measurements on the TFR 600 Tokamak

Energy Technology Data Exchange (ETDEWEB)

Soltwisch, H [Kernforschungsanlage Juelich G.m.b.H. (Germany, F.R.). Inst. fuer Plasmaphysik; Association Euratom-Kernforschungsanlage Juelich G.m.b.H. (Germany, F.R.)); Equipe, T F.R. [Association Euratom-CEA sur la Fusion, Centre d' Etudes Nucleaires de Fontenay-aux-Roses, 92 (France). Dept. de Recherches sur la Fusion Controlee

1981-09-01

The results are reported on the feasibility of using far-infrared polarimetry for Faraday rotation diagnostic measurements on the TRF Tokamak. Precise quantitative results were not obtained but a satisfactory agreement with a simple theoretical model leads to a good understanding of the experimental limitations of the method.

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .2. DESIGN EVALUATION ON MEASURED DATA

NARCIS (Netherlands)

DUINEVELD, C. A. A.; Smilde, A. K.; Doornbos, D. A.

1993-01-01

The construction of a small experimental design for a combination of process and mixture variables is a problem which has not been solved completely by now. In a previous paper we evaluated some designs with theoretical measures. This second paper evaluates the capabilities of the best of these

COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .2. DESIGN EVALUATION ON MEASURED DATA

NARCIS (Netherlands)

DUINEVELD, CAA; SMILDE, AK; DOORNBOS, DA

The construction of a small experimental design for a combination of process and mixture variables is a problem which has not been solved completely by now. In a previous paper we evaluated some designs with theoretical measures. This second paper evaluates the capabilities of the best of these

Measurement approaches to support future warhead arms control transparency

International Nuclear Information System (INIS)

Olinger, C.T.; Frankle, C.M.; Johnson, M.W.; Poths, J.

1998-01-01

Transparency on warhead stockpiles, warhead dismantlement, and fissile material stockpiles in nuclear weapons states will become increasingly important in the move beyond START II toward lower quantities of warheads. Congressional support for further warhead reductions will likely depend on the degree of irreversibility, or in other words, the rapidity with which warhead inventories could be reconstituted. Whether irreversibility considerations can be satisfied will depend on monitoring dismantlement as well as constraining the available stockpile of fissile materials for possible refabrication into warheads. Measurement techniques designed to address the above problems will need to consider NPT Article 1 obligations as well as Russian and US classification regulations, which prohibit or restrict the transfer of nuclear warhead design information to other states. Classification considerations currently limit the potential completeness of future inspections of weapons materials. Many conventional international safeguards approaches are not currently viable for arms control applications because they would reveal weapons design information. The authors discuss a variety of technical measures that may help to improve transparence of warhead and fissile material stockpiles and may enable limited warhead dismantlement transparency

Experimental measurement of the 12C+16O fusion cross sections at astrophysical energies

Science.gov (United States)

Fang, X.; Tan, W. P.; Beard, M.; deBoer, R. J.; Gilardy, G.; Jung, H.; Liu, Q.; Lyons, S.; Robertson, D.; Setoodehnia, K.; Seymour, C.; Stech, E.; Vande Kolk, B.; Wiescher, M.; de Souza, R.; Hudan, S.; Singh, V.; Tang, X. D.; Uberseder, E.

2018-05-01

The total cross sections of the 12C+16O fusion have been experimentally determined at low energies to investigate the role of this reaction during late stellar evolution burning phases. A high-intensity oxygen beam was produced by the 5MV pelletron accelerator at the University of Notre Dame impinging on a thick ultra-pure graphite target. Protons and γ-rays were measured simultaneously in the center-of-mass energy range from 3.64 to 5.01 MeV, using strip silicon and HPGe detectors. Statistical model calculations were employed to interpret the experimental results. A new broad resonance-like structure is observed for the 12C+16O reaction, and a decreasing trend of its S-factor towards low energies is found.

How supportive supervision influences immunization session site practices: a quasi-experimental study in Odisha, India.

Science.gov (United States)

Panda, Bhuputra; Pati, Sanghamitra; Nallala, Srinivas; Chauhan, Abhimanyu S; Anasuya, Anita; Som, Meena; Zodpey, Sanjay

2015-01-01

Routine immunization (RI) is a key child survival intervention. Ensuring acceptable standards of RI service delivery is critical for optimal outcomes. Accumulated evidences suggest that 'supportive supervision' improves the quality of health care services in general. During 2009-2010, the Government of Odisha and UNICEF jointly piloted this strategy in four districts to improve RI program outcomes. The present study aims to assess the effect of this strategy on improvement of skills and practices at immunization session sites. A quasi-experimental 'post-test only' study design was adopted to compare the opinion and practices of frontline health workers and their supervisors in four intervention districts (IDs) with two control districts (CDs). Altogether, we interviewed 111 supervisor-supervisee (health worker) pairs using semi-structured interview schedules and case vignettes. We also directly observed health workers' practices during immunization sessions at 111 sites. Data were analyzed with SPSS version 16.0. The mean knowledge score of supervisors in CDs was significantly higher than in intervention groups. Variegated responses were obtained on case vignettes. The control group performed better in solving certain hypothetically asked problems, whereas the intervention group scored better in others. Health workers in IDs gave a lower rating to their respective supervisors' knowledge, skill, and frequency of supervision. Logistics and vaccine availability were better in CDs. Notwithstanding other limitations, supportive supervision may not have independent effects on improving the quality of immunization services. Addressing systemic issues, such as the availability of essential logistics, supply chain management, timely indenting, and financial resources, could complement the supportive supervision strategy in improving immunization service delivery.

Experimentally measuring a quantum state by the Heisenberg exchange interaction in a single apparatus

International Nuclear Information System (INIS)

Peng Xinhua; Du Jiangfeng; Suter, D.

2005-01-01

Full text: Quantum information processing requires the effective measurement of quantum states. An important method, called quantum state tomography, needs measuring a complete set of observables on the measured system to determine its unknown quantum state ρ. The measurement involves certain noncommuting observables as a result of Bohr's complementarity. Very recently, Allahverdyan et al. proposed a new method in which the unknown quantum state r is determined by measuring a set of commuting observables in the price of a controlled interaction with an auxiliary system. If both systems S and A are spins, their z components (σ z ) can be chosen to measure after some specific Heisenberg exchange interaction. We study in detail a general Heisenberg XYZ model for a two-qubit system and present two classes of special Heisenberg interactions which can serve as the controlled interaction in Allahverdyan's scheme when the state of the auxiliary system A is initially completely disordered. Using the nuclear magnetic resonance techniques, the measurement scheme in a single apparatus has been experimentally demonstrated by designing the quantum circuit to simulate the Heisenberg exchange interaction. (author)

Experimental measurement of dolphin thrust generated during a tail stand using DPIV

Science.gov (United States)

Wei, Timothy; Fish, Frank; Williams, Terrie; Wu, Vicki; Sherman, Erica; Misfeldt, Mitchel; Ringenberg, Hunter; Rogers, Dylan

2016-11-01

The thrust generated by dolphins doing tail stands was measured using DPIV. The technique entailed measuring vortex strength associated with the tail motion and correlating it to above water video sequences showing the amount of the dolphin's body that was being lifted out of the water. The underlying drivers for this research included: i) understanding the physiology, hydrodynamics and efficiency of dolphin locomotion, ii) developing non-invasive measurement techniques for studying marine swimming and iii) quantifying the actual propulsive capabilities of these animals. Two different bottlenose dolphins at the Long Marine Lab at UC-Santa Cruz were used as test subjects. Application of the Kutta-Joukowski Theorem on measured vortex circulations yielded thrust values that were well correlated with estimates of dolphin body weight being supported above water. This demonstrates that the tail motion can be interpreted as a flapping hydrofoil that can generate a sustained thrust roughly equal to the dolphin's weight. Videos of DPIV measurements overlaid with the dolphins will be presented along with thrust/weight data.

An experimental study on a training support system utilizing trainee's eye gaze point and think aloud protocol for diagnosing nuclear power plant anomalies

International Nuclear Information System (INIS)

Ozawa, Takahisa; Samejima, Ryouta; Shimoda, Hiroshi; Yoshikawa, Hidekazu

2003-01-01

An experimental system has been developed for aiming at supporting the simulator training of diagnosis nuclear power plant anomaly, where an expert provides the instructions to a trainee by his/her own educational and experienced point of view. This system has several characteristics as follows: (1) the expert can provide the instruction through the local area network or the Internet, (2) the training task is the detection of the primary cause of plant anomaly, which is not including the plant operation but requires only thinking, and (3) the system can automatically detects the trainee's view-point and think aloud protocols and provide these two types of information to the expert in real time for supporting his/her instruction. A laboratory experiment using this system was conducted, where an expert, who had really engaged in plant operation as a chief operator, was employed as the instructor for novice students. As the result of analyzing the experimental data, it was found that the two types of information, trainee's viewpoints and his verbal protocols, have some potential of effectiveness for supporting the instructor to estimate the trainees diagnostic thinking process and provide the instruction. (author)

Rock support of the L3 experimental hall complex

International Nuclear Information System (INIS)

Laughton, C.

1990-06-01

The methods of excavation and support selected for the LEP works are discussed in this paper. The excavation of the halls and chambers in discrete passes, from the roof down, and their temporary support by patterned fully bonded rock bolts and shotcrete ensured that mass deformations were contained. When working in soft rock materials where discontinuity, elastic and possibly plastic deformations may each play an important role in the overall rock structure stability, it is of paramount importance to systematically monitor the behavior of the rock in-situ. The use of instrumentation to indicate location, direction, levels, and rate of movement is essential to ensure that a safe, efficient and economical mining operation can be undertaken, and that any remedial action will be taken at the appropriate time. The use of the New Austrian Tunneling support mechanisms allowed the engineer greater flexibility in handling local reinforcement of the rock structure if superficial or relatively deep-seated instability was encountered. However, in the case where second linings are to be accommodated and flexible support mechanisms used, care should be taken to foresee over-excavation in weaker zones to allow for larger displacements prior to the attainment of confinement-convergence equilibria. 4 refs., 7 figs

Technical note: An experimental set-up to measure latent and sensible heat fluxes from (artificial plant leaves

Directory of Open Access Journals (Sweden)

S. J. Schymanski

2017-07-01

Full Text Available Leaf transpiration and energy exchange are coupled processes that operate at small scales yet exert a significant influence on the terrestrial hydrological cycle and climate. Surprisingly, experimental capabilities required to quantify the energy–transpiration coupling at the leaf scale are lacking, challenging our ability to test basic questions of importance for resolving large-scale processes. The present study describes an experimental set-up for the simultaneous observation of transpiration rates and all leaf energy balance components under controlled conditions, using an insulated closed loop miniature wind tunnel and artificial leaves with pre-defined and constant diffusive conductance for water vapour. A range of tests documents the above capabilities of the experimental set-up and points to potential improvements. The tests reveal a conceptual flaw in the assumption that leaf temperature can be characterized by a single value, suggesting that even for thin, planar leaves, a temperature gradient between the irradiated and shaded or transpiring and non-transpiring leaf side can lead to bias when using observed leaf temperatures and fluxes to deduce effective conductances to sensible heat or water vapour transfer. However, comparison of experimental results with an explicit leaf energy balance model revealed only minor effects on simulated leaf energy exchange rates by the neglect of cross-sectional leaf temperature gradients, lending experimental support to our current understanding of leaf gas and energy exchange processes.

1988 Progress report of the EDF department for the analysis of experimental data and measurements

International Nuclear Information System (INIS)

Anon.

1988-01-01

The 1988 activity report of the department for the analysis of experimental data and measurements (Department of Retour d'Experience Mesures-Essais, of EDF, France), is presented. The mission of the department is to collect and investigate data from the nuclear power plant operations. The investigations started before 1988, were carried on in 1988. The department main activities are: technology and information transfer from experimental activities, the construction of a standard data acquisition and processing system, the actions involving the N4 turbine, and the modelling and construction of new non-destructive methods of control. The most important facts and activities carried out in 1988 are presented [fr

An experimental technique for the direct measurement of N2O5 reactivity on ambient particles

Directory of Open Access Journals (Sweden)

T. H. Bertram

2009-06-01

Full Text Available An experimental approach for the direct measurement of trace gas reactivity on ambient aerosol particles has been developed. The method utilizes a newly designed entrained aerosol flow reactor coupled to a custom-built chemical ionization mass spectrometer. The experimental method is described via application to the measurement of the N2O5 reaction probability, γ (N2O5. Laboratory investigations on well characterized aerosol particles show that measurements of γ (N2O5 observed with this technique are in agreement with previous observations, using conventional flow tube methods, to within ±20% at atmospherically relevant particle surface area concentrations (0–1000 μm2 cm−3. Uncertainty in the measured γ (N2O5 is discussed in the context of fluctuations in potential ambient biases (e.g., temperature, relative humidity and trace gas loadings. Under ambient operating conditions we estimate a single-point uncertainty in γ (N2O5 that ranges between ± (1.3×10-2 + 0.2×γ (N2O5, and ± (1.3×10-3 + 0.2×γ (N2O5 for particle surface area concentrations of 100 to 1000 μm2 cm−3, respectively. Examples from both laboratory investigations and field observations are included alongside discussion of future applications for the reactivity measurement and optimal deployment locations and conditions.

Experimental study on performance verification tests for coordinate measuring systems with optical distance sensors

Science.gov (United States)

Carmignato, Simone

2009-01-01

Optical sensors are increasingly used for dimensional and geometrical metrology. However, the lack of international standards for testing optical coordinate measuring systems is currently limiting the traceability of measurements and the easy comparison of different optical systems. This paper presents an experimental investigation on artefacts and procedures for testing coordinate measuring systems equipped with optical distance sensors. The work is aimed at contributing to the standardization of testing methods. The VDI/VDE 2617-6.2:2005 guideline, which is probably the most complete document available at the state of the art for testing systems with optical distance sensors, is examined with specific experiments. Results from the experiments are discussed, with particular reference to the tests used for determining the following characteristics: error of indication for size measurement, probing error and structural resolution. Particular attention is given to the use of artefacts alternative to gauge blocks for determining the error of indication for size measurement.

Shielding Characteristics Using an Ultrasonic Configurable Fan Artificial Noise Source to Generate Modes - Experimental Measurements and Analytical Predictions

Science.gov (United States)

Sutliff, Daniel L.; Walker, Bruce E.

2014-01-01

An Ultrasonic Configurable Fan Artificial Noise Source (UCFANS) was designed, built, and tested in support of the NASA Langley Research Center's 14x22 wind tunnel test of the Hybrid Wing Body (HWB) full 3-D 5.8% scale model. The UCFANS is a 5.8% rapid prototype scale model of a high-bypass turbofan engine that can generate the tonal signature of proposed engines using artificial sources (no flow). The purpose of the program was to provide an estimate of the acoustic shielding benefits possible from mounting an engine on the upper surface of a wing; a flat plate model was used as the shielding surface. Simple analytical simulations were used to preview the radiation patterns - Fresnel knife-edge diffraction was coupled with a dense phased array of point sources to compute shielded and unshielded sound pressure distributions for potential test geometries and excitation modes. Contour plots of sound pressure levels, and integrated power levels, from nacelle alone and shielded configurations for both the experimental measurements and the analytical predictions are presented in this paper.

Experimental study of a variable-capacitance micromotor with electrostatic suspension

Science.gov (United States)

Han, F. T.; Wu, Q. P.; Wang, L.

2010-11-01

A variable-capacitance micromotor where the rotor is supported electrostatically in five degrees of freedom was designed, fabricated and tested in order to study the behavior of this electrostatic motor. The micromachined device is based on a glass/silicon/glass stack bonding structure, fabricated by bulk micromachining and initially operated in atmospheric environment. The analytical torque model is obtained by calculating the capacitances between different stator electrodes and the rotor. Capacitance values in the order of 10-13 pF and torque values in the order of 10-10 N m have been calculated from the motor geometry and attainable drive voltage. A dynamic model of the motor is proposed by further estimating the air-film damping effect in an effort to explain the experimental rotation measurements. Experimental results of starting voltage, continuous operation, switching response and electric bearing of the micromotor are presented and discussed. Preliminary measurements indicate that a rotor rotating speed of 73.3 r min-1 can be achieved at a drive voltage of 28.3 V, equivalent to a theoretical motive torque of 517 pN m. Starting voltage results obtained from experimental measurement are in agreement with the developed dynamic model.

Implant-supported mandibular removable partial dentures; patient-based outcome measures in relation to implant position.

Science.gov (United States)

Jensen, Charlotte; Raghoebar, Gerry M; Kerdijk, Wouter; Meijer, Henny J A; Cune, Marco S

2016-12-01

To assess the benefits of implant support to Removable Partial Dentures (RPD) in patients with a bilateral free-ending situation in the mandible and to determine the most favorable implant position: the premolar (PM) or the molar (M) region. Thirty subjects with a bilateral unbounded posterior saddle received 2 PM and 2M implants. A new RPD was placed. Implant support was provided 3 months later. Two PM implants supported the RPD. After 3 months the 2M implants were used or vice versa. Outcome measures included oral health related quality of life (OHIP-NL49), general health status (SF-36), contentment assessed on a Visual Analogue Scale (VAS) and the number of hours that the RPD was worn. Data were collected prior to treatment, 3 months after having functioned with a new RPD and after 3 and 6 months with implant support. Finally, patients expressed their preferred implant position. The general health status (SF-36) was not influenced. OHIP-NL49 values and mean wearing-time were statistical significantly more favorable for ISRPD's, regardless of the implant position. Per day, the ISRPD's were worn 2-3h more than the unsupported new RPD. Patients' expectations were met as the VAS-scores of anticipated and realized contentment did not reach a statistical significant level (p>0.05). VAS scores for ISRPD's with M implant support were higher than for PM implant support. Finally, 56.7% of subjects preferred the M implant support, 13.3% expressed no preference and 30% opted for PM implant support. Mandibular implant support favorably influences oral health related patient-based outcome measures in patients with a bilateral free-ending situation. The majority of patients prefer the implant support to be in the molar region. Patients with a bilateral free-ending situation in the mandible opposed by a maxillary denture benefit from implant support to their mandibular removable partial denture. Most patients prefer this support to be in the molar region. Copyright © 2016

Experimental Measurement of Relative Permeability Functions for Fuel Cell GDL Materials

KAUST Repository

Hussaini, Irfan; Wang, Chao-Yang

2009-01-01

Gas diffusion layer in PEM fuel cells plays a pivotal role in water management. Modeling of liquid water transport through the GDL relies on knowledge of relative permeability functions in the in-plane and through-plane directions. In the present work, air and water relative permeabilities are experimentally determined as functions of saturation for typical GDL materials such as Toray-060, -090, -120 carbon paper and E-Tek carbon cloth materials in their plain, untreated forms. Saturation is measured using an ex-situ gravimetric method. Absolute and relative permeability functions in the two directions of interest are presented. Significant departure from the generally assumed cubic function of saturation is observed. ©The Electrochemical Society.

Experimental measurement of compressibility coefficients of synthetic sandstone in hydrostatic conditions

International Nuclear Information System (INIS)

Asaei, H; Moosavi, M

2013-01-01

For the characterization of the mechanical behavior of porous media in elastic conditions, the theory of poroelasticity is used. The number of poroelastic coefficients is greater in elastic conditions because of the complexity of porous media. The laboratory measurement of poroelastic coefficients needs a system that can control and measure the variables of poroelasticity. In this paper, experimental measurements of these coefficients are presented. Laboratory tests are performed using a system designed by the authors. Laboratory hydrostatic tests are performed on cylindrical samples in drained, pore pressure loading, undrained and dry conditions. Compressibilities (bulk and pore compressibility), effective stress and Skempton coefficients are measured by these tests. Samples are made of a composition (sand and cement) and are made by a compaction process synthetically. Calibration tests are performed for the setup to identify possible errors in the system and to correct the results of the main tests. This is done by performing similar compressibility tests at each stress level on a cylindrical steel sample (5.47 mm in diameter) with a longitudinal hole along it (hollow cylinder). A steel sample is used to assume an incompressible sample. The results of the tests are compared with the theory of poroelasticity and the obtained graphs and their errors are analyzed. This study shows that the results of the drained and pore pressure loading tests are compatible with poroelastic formulation, while the undrained results have errors because of extra fluid volume in the pore pressure system and calibration difficulties. (paper)

Uncertainty in techno-economic estimates of cellulosic ethanol production due to experimental measurement uncertainty

Directory of Open Access Journals (Sweden)

Vicari Kristin J

2012-04-01

Full Text Available Abstract Background Cost-effective production of lignocellulosic biofuels remains a major financial and technical challenge at the industrial scale. A critical tool in biofuels process development is the techno-economic (TE model, which calculates biofuel production costs using a process model and an economic model. The process model solves mass and energy balances for each unit, and the economic model estimates capital and operating costs from the process model based on economic assumptions. The process model inputs include experimental data on the feedstock composition and intermediate product yields for each unit. These experimental yield data are calculated from primary measurements. Uncertainty in these primary measurements is propagated to the calculated yields, to the process model, and ultimately to the economic model. Thus, outputs of the TE model have a minimum uncertainty associated with the uncertainty in the primary measurements. Results We calculate the uncertainty in the Minimum Ethanol Selling Price (MESP estimate for lignocellulosic ethanol production via a biochemical conversion process: dilute sulfuric acid pretreatment of corn stover followed by enzymatic hydrolysis and co-fermentation of the resulting sugars to ethanol. We perform a sensitivity analysis on the TE model and identify the feedstock composition and conversion yields from three unit operations (xylose from pretreatment, glucose from enzymatic hydrolysis, and ethanol from fermentation as the most important variables. The uncertainty in the pretreatment xylose yield arises from multiple measurements, whereas the glucose and ethanol yields from enzymatic hydrolysis and fermentation, respectively, are dominated by a single measurement: the fraction of insoluble solids (fIS in the biomass slurries. Conclusions We calculate a $0.15/gal uncertainty in MESP from the TE model due to uncertainties in primary measurements. This result sets a lower bound on the error bars of

Experimental measurement and modeling analysis on mechanical properties of incudostapedial joint.

Science.gov (United States)

Zhang, Xiangming; Gan, Rong Z

2011-10-01

The incudostapedial (IS) joint between the incus and stapes is a synovial joint consisting of joint capsule, cartilage, and synovial fluid. The mechanical properties of the IS joint directly affect the middle ear transfer function for sound transmission. However, due to the complexity and small size of the joint, the mechanical properties of the IS joint have not been reported in the literature. In this paper, we report our current study on mechanical properties of human IS joint using both experimental measurement and finite element (FE) modeling analysis. Eight IS joint samples with the incus and stapes attached were harvested from human cadaver temporal bones. Tension, compression, stress relaxation and failure tests were performed on those samples in a micro-material testing system. An analytical approach with the hyperelastic Ogden model and a 3D FE model of the IS joint including the cartilage, joint capsule, and synovial fluid were employed to derive mechanical parameters of the IS joint. The comparison of measurements and modeling results reveals the relationship between the mechanical properties and structure of the IS joint.

Unaccounted source of systematic errors in measurements of the Newtonian gravitational constant G

Science.gov (United States)

DeSalvo, Riccardo

2015-06-01

Many precision measurements of G have produced a spread of results incompatible with measurement errors. Clearly an unknown source of systematic errors is at work. It is proposed here that most of the discrepancies derive from subtle deviations from Hooke's law, caused by avalanches of entangled dislocations. The idea is supported by deviations from linearity reported by experimenters measuring G, similarly to what is observed, on a larger scale, in low-frequency spring oscillators. Some mitigating experimental apparatus modifications are suggested.

Do informal caregivers for elderly in the community use support measures? A qualitative study in five European countries.

Science.gov (United States)

Willemse, Evi; Anthierens, Sibyl; Farfan-Portet, Maria Isabel; Schmitz, Olivier; Macq, Jean; Bastiaens, Hilde; Dilles, Tinne; Remmen, Roy

2016-07-16

Informal caregivers are essential figures for maintaining frail elderly at home. Providing informal care can affect the informal caregivers' physical and psychological health and labour market participation capabilities. They need support to prevent caregiver burden. A variety of existing support measures can help the caregiver care for the elderly at home, but with some limitations. The objective of this review was to explore the experiences of informal caregivers caring for elderly in the community with the use of supportive policy measures in Belgium and compare these to the experiences in other European countries. An empirical qualitative case study research was conducted in five European countries (Belgium, The Netherlands, Luxembourg, France and Germany). Semi-structured interviews were conducted with informal caregivers and their dependent elderly. Interview data from the different cases were analysed. In particular data from Belgium was compared to data from the cases abroad. Formal services (e.g. home care) were reported to have the largest impact on allowing the caregiver to care for the dependent elderly at home. One of the key issues in Belgium is the lack of timely access to reliable information about formal and informal services in order to proactively support the informal caregiver. Compared to the other countries, informal caregivers in Belgium expressed more difficulties in accessing support measures and navigating through the health system. In the other countries information seemed to be given more timely when home care was provided via care packages. To support the informal caregiver, who is the key person to support the frail elderly, fragmentation of information regarding supportive policy measures is an important issue of concern.

Note: Comparison experimental results of the laser heterodyne interferometer for angle measurement based on the Faraday effect

Science.gov (United States)

Zhang, Enzheng; Chen, Benyong; Zheng, Hao; Teng, Xueying; Yan, Liping

2018-04-01

A laser heterodyne interferometer for angle measurement based on the Faraday effect is proposed. A novel optical configuration, designed by using the orthogonal return method for a linearly polarized beam based on the Faraday effect, guarantees that the measurement beam can return effectively even though an angular reflector has a large lateral displacement movement. The optical configuration and measurement principle are presented in detail. Two verification experiments were performed; the experimental results show that the proposed interferometer can achieve a large lateral displacement tolerance of 7.4 mm and also can realize high precision angle measurement with a large measurement range.

Business incubator as a support measure for start-ups in Russia and Sweden. : Comparative analysis.

OpenAIRE

Kiseleva, Maria

2017-01-01

Growth and developing of start-ups plays an important role as starting new business is one of the indicator that shows the economy level of each country. At that time start-ups need support and one of such support institutions is business incubator who can provide all resources that start-ups need. Different studies exist about business incubator as a support measure and the role of them for start- ups, but there is a lack of studies in analyzing this topic in different business environments....

Experimental comparison of support vector machines with random ...

Indian Academy of Sciences (India)

dient method, support vector machines, and random forests to improve producer accuracy and overall classification accuracy. The performance comparison of these classifiers is valuable for a decision maker ... ping, surveillance system, resource management, tracking ... rocks, water bodies, and anthropogenic elements,.

The effects of gait training with body weight support (BWS) with no body weight support (no-BWS) in stroke patients.

Science.gov (United States)

Ullah, Muhammad Asad; Shafi, Hina; Khan, Ghazanfar Ali; Malik, Arshad Nawaz; Amjad, Imran

2017-07-01

The purpose of this study was to measure the clinical outcomes for patients with stroke after gait training with body weight support (BWS) and with no body weight support (no-BWS).Experimental group was trained to walk by a BWS system with overhead harness (BWS group), and Control group was trained with full weight bearing walk on their lower extremities. Treatment session comprised of six weeks training. Treatment outcomes were assessed on the basis of Timed 10 Meter Walk Test, Timed Get Up and Go Test and Dynamic Gait Index. There was a significant (PTraining of gait in stroke patients while a percentage of their body weight supported by a harness, resulted in better walking abilities than the Training of gait while full weight was placed on patient's lower extremities.

Hypersonic nozzle/afterbody CFD code validation. I - Experimental measurements

Science.gov (United States)

Spaid, Frank W.; Keener, Earl R.

1993-01-01

This study was conducted to obtain a detailed experimental description of the flow field created by the interaction of a single-expansion-ramp-nozzle flow with a hypersonic external stream. Data were obtained from a generic nozzle/afterbody model in the 3.5-Foot Hypersonic Wind Tunnel of the NASA Ames Research Center in a cooperative experimental program involving Ames and the McDonnell Douglas Research Laboratories. This paper presents experimental results consisting primarily of surveys obtained with a five-hole total-pressure/flow-direction probe and a total-temperature probe. These surveys were obtained in the flow field created by the interaction between the underexpanded jet plume and the external flow.

Role of Social Support in Improving Infant Feeding Practices in Western Kenya: A Quasi-Experimental Study.

Science.gov (United States)

Mukuria, Altrena G; Martin, Stephanie L; Egondi, Thaddeus; Bingham, Allison; Thuita, Faith M

2016-03-01

We designed and tested an intervention that used dialogue-based groups to engage infants' fathers and grandmothers to support optimal infant feeding practices. The study's aim was to test the effectiveness of increased social support by key household influencers on improving mothers' complementary feeding practices. Using a quasi-experimental design, we enrolled mothers, fathers, and grandmothers from households with infants 6-9 months old in 3 rural communities (1 intervention arm with fathers, 1 intervention arm with grandmothers, and 1 comparison arm) in western Kenya. We engaged 79 grandmothers and 85 fathers in separate dialogue groups for 6 months from January to July 2012. They received information on health and nutrition and were encouraged to provide social support to mothers (defined as specific physical actions in the past 2 weeks or material support actions in the past month). We conducted a baseline household survey in December 2011 in the 3 communities and returned to the same households in July 2012 for an endline survey. We used a difference-in-difference (DiD) approach and logistic regression to evaluate the intervention. We surveyed 554 people at baseline (258 mothers, 165 grandmothers, and 131 fathers) and 509 participants at endline. The percentage of mothers who reported receiving 5 or more social support actions (of a possible 12) ranged from 58% to 66% at baseline in the 3 groups. By endline, the percentage had increased by 25.8 percentage points (P=.002) and 32.7 percentage points (P=.001) more in the father and the grandmother intervention group, respectively, than in the comparison group. As the number of social support actions increased in the 3 groups, the likelihood of a mother reporting that she had fed her infant the minimum number of meals in the past 24 hours also increased between baseline and endline (odds ratio [OR], 1.14; confidence interval [CI], 1.00 to 1.30; P=.047). When taking into account the interaction effects of

How supportive supervision influences immunization session site practices: a quasi-experimental study in Odisha, India

Directory of Open Access Journals (Sweden)

Bhuputra Panda

2015-01-01

Full Text Available Background: Routine immunization (RI is a key child survival intervention. Ensuring acceptable standards of RI service delivery is critical for optimal outcomes. Accumulated evidences suggest that ‘supportive supervision’ improves the quality of health care services in general. During 2009–2010, the Government of Odisha and UNICEF jointly piloted this strategy in four districts to improve RI program outcomes. The present study aims to assess the effect of this strategy on improvement of skills and practices at immunization session sites. Design: A quasi-experimental ‘post-test only’ study design was adopted to compare the opinion and practices of frontline health workers and their supervisors in four intervention districts (IDs with two control districts (CDs. Altogether, we interviewed 111 supervisor–supervisee (health worker pairs using semi-structured interview schedules and case vignettes. We also directly observed health workers’ practices during immunization sessions at 111 sites. Data were analyzed with SPSS version 16.0. Results: The mean knowledge score of supervisors in CDs was significantly higher than in intervention groups. Variegated responses were obtained on case vignettes. The control group performed better in solving certain hypothetically asked problems, whereas the intervention group scored better in others. Health workers in IDs gave a lower rating to their respective supervisors’ knowledge, skill, and frequency of supervision. Logistics and vaccine availability were better in CDs. Conclusion: Notwithstanding other limitations, supportive supervision may not have independent effects on improving the quality of immunization services. Addressing systemic issues, such as the availability of essential logistics, supply chain management, timely indenting, and financial resources, could complement the supportive supervision strategy in improving immunization service delivery.

A measurement evaluation program to support nuclear material control and accountability measurements in Brazilian laboratories

International Nuclear Information System (INIS)

Dias, Fabio C.; Mason, Peter

2013-01-01

A measurement evaluation program (MEP) is one of a number of valuable tools that analytical chemists can use to ensure that the data produced in the laboratory are fit for their intended purpose and consistent with expected performance values at a given time. As such, participation in a MEP is an important indicator of the quality of analytical data, and is recognized as such by independent regulatory and/or accreditation bodies. With the intent to implement such a program in Brazil, in November 2012 the Nuclear Energy Commission of Brazil (CNEN), with support from the Department of Energy of the United States' (US-DOE International Safeguards and Engagement Program), decided to initiate a technical cooperation project aiming at organizing a Safeguards Measurement Evaluation Program (SMEP) for Brazilian facilities. The project, entitled Action Sheet 23, was formalized under the terms of the Agreement between the US-DOE and the CNEN concerning research and development in nuclear material control, accountancy, verification, physical protection, and advanced containment and surveillance technologies for International Safeguards Applications. The work, jointly performed by the CNEN's Safeguards Laboratory (LASAL) and the New Brunswick Laboratory (NBL), has the objective to strengthen the traceability of accountability measurements and ensure adequate quality of safeguards measurements for facilities within Brazil, utilizing test samples characterized and provided by NBL. Recommendations to participants included measurement frequency, number of results per sample and format for reporting results using ISO methods for calculating and expressing measurement uncertainties. In this paper, we discuss the main steps taken by CNEN and NBL aiming at implementing such a program and the expected results, in particular the impact of uncertainty estimation on the evaluation of performance of each participant laboratory. The program is considered by Brazilian safeguards authorities

A measurement evaluation program to support nuclear material control and accountability measurements in Brazilian laboratories

Energy Technology Data Exchange (ETDEWEB)

Dias, Fabio C., E-mail: fabio@ird.gov.br [Comissao Nacional de Energia Nuclear (CNEN-RJ), Rio de Janeiro, RJ (Brazil); Mason, Peter, E-mail: peter.mason@ch.doe.gov [New Brunswick Laboratory (DOE/NBL), Argonne, IL (United States)

2013-07-01

A measurement evaluation program (MEP) is one of a number of valuable tools that analytical chemists can use to ensure that the data produced in the laboratory are fit for their intended purpose and consistent with expected performance values at a given time. As such, participation in a MEP is an important indicator of the quality of analytical data, and is recognized as such by independent regulatory and/or accreditation bodies. With the intent to implement such a program in Brazil, in November 2012 the Nuclear Energy Commission of Brazil (CNEN), with support from the Department of Energy of the United States' (US-DOE International Safeguards and Engagement Program), decided to initiate a technical cooperation project aiming at organizing a Safeguards Measurement Evaluation Program (SMEP) for Brazilian facilities. The project, entitled Action Sheet 23, was formalized under the terms of the Agreement between the US-DOE and the CNEN concerning research and development in nuclear material control, accountancy, verification, physical protection, and advanced containment and surveillance technologies for International Safeguards Applications. The work, jointly performed by the CNEN's Safeguards Laboratory (LASAL) and the New Brunswick Laboratory (NBL), has the objective to strengthen the traceability of accountability measurements and ensure adequate quality of safeguards measurements for facilities within Brazil, utilizing test samples characterized and provided by NBL. Recommendations to participants included measurement frequency, number of results per sample and format for reporting results using ISO methods for calculating and expressing measurement uncertainties. In this paper, we discuss the main steps taken by CNEN and NBL aiming at implementing such a program and the expected results, in particular the impact of uncertainty estimation on the evaluation of performance of each participant laboratory. The program is considered by Brazilian safeguards

Experimental system using an active method for the measurement of low alpha emitter grades

International Nuclear Information System (INIS)

Bernard, P.; Cance, M.

1986-06-01

The diversity of waste produced in France, the limitations of passive neutron measurements, the new safety requirements in the field of low level waste disposal have induced us to develop active neutron techniques. Two experimental pulsed neutron interrogation systems are described giving a sensitivity lower than 10 mg Pu 239 in 200 l drums. This project is the result of a close cooperation between the CEA, SGN and SODERN

A theory of local and global processes which affect solar wind electrons. 2. Experimental support

International Nuclear Information System (INIS)

Scudder, J.D.; Olbert, S.

1979-05-01

The microscopic characteristics of the Coulomb cross section show that there are three natural subpopulations for plasma electrons: the subthermals; the transthermals; and the extrathermals. Data from three experimental groups on three different spacecraft in the interplanetary medium over a radial range are presented to support the five interrelations projected between solar wind electron properties and changes in the interplanetary medium: (1) subthermals respond primarily to local changes (compression and rarefactions) in stream dynamics; (2) the extrathermal fraction of the ambient electron density should be anti-correlated with the asymptotic bulk speed; (3) the extrathermal 'temperature' should be anti-correlated with the local wind speed at 1 AU; (4) the heat flux carried by electrons should be anti-correlated with the local bulk speed; and (5) the extrathermal differential 'temperature' should be nearly independent of radius within 1 AU

Support for Alzheimer's Caregivers: Psychometric Evaluation of Familial and Friend Support Measures

Science.gov (United States)

Wilks, Scott E.

2009-01-01

Objective: Information on the shortened, 20-item version of the Perceived Social Support Scale (S-PSSS) is scarce. The purpose of this study is to evaluate the psychometric properties of the S-PSSS Family (SSfa) and Friends (SSfr) subscales. Method: Because of their common coping method of social support, a cross-sectional sample of Alzheimer's…

An experimental model for measuring gastrointestinal bleeding rate using Tc-99m DTPA in rabbits

International Nuclear Information System (INIS)

Owunwanne, A.; Abdel-Dayem, H.M.; Sadek, S.; Yakoub, T.; Mahajan, K.K.; Ericsson, S.B.

1987-01-01

An animal experimental model to measure the rate of gastrointestinal bleeding rate in a rabbit using Tc-99m DTPA is described. It was possible to detect a bleeding rate of 0.1 ml/min. However, the model could not be used to calculate the minimum amount of radioactivity needed to detect the bleeding site. (orig.) [de

Experimental measurement of magnetic field null in the vacuum chamber of KTM tokamak based on matrix of 2D Hall sensors

Energy Technology Data Exchange (ETDEWEB)

Shapovalov, G.; Chektybayev, B., E-mail: chektybaev@nnc.kz; Sadykov, A.; Skakov, M.; Kupishev, E.

2016-11-15

Experimental technique of measurement of magnetic field null region inside of the KTM tokamak vacuum chamber has been developed. Square matrix of 36 2D Hall sensors, which used in the technique, allows carrying out direct measurements of poloidal magnetic field dynamics in the vacuum chamber. To better measuring accuracy, Hall sensor’s matrix was calibrated with commercial Helmholtz coils and in situ measurement of defined magnetic field from poloidal and toroidal coils. Standard KTM Data-Acquisition System has been used to collect data from Hall sensors. Experimental results of measurement of magnetic field null in the vacuum chamber of KTM are shown in the paper. Additionally results of the magnetic field null reconstruction from signals of inductive total flux loops are shown in the paper.

Weak measurement and its experimental realisation

International Nuclear Information System (INIS)

Flack, R; Hiley, B J

2014-01-01

The relationship between the real part of the weak value of the momentum operator at a post selected position is discussed and the meaning of the experimentally determined stream-lines in the Toronto experiment of Kocsis et al is re-examined. We argue against interpreting the energy flow lines as photon trajectories. The possibility of performing an analogous experiment using atoms is proposed in order that a direct comparison can be made with the trajectories calculated by Philippidis, Dewdney and Hiley using the Bohm approach.

Effect of Electron Seeding on Experimentally Measured Multipactor Discharge Threshold

Science.gov (United States)

Noland, Jonathan; Graves, Timothy; Lemon, Colby; Looper, Mark; Farkas, Alex

2012-10-01

Multipactor is a vacuum phenomenon in which electrons, moving in resonance with an externally applied electric field, impact material surfaces. If the number of secondary electrons created per primary electron impact averages more than unity, the resonant interaction can lead to an electron avalanche. Multipactor is a generally undesirable phenomenon, as it can cause local heating, absorb power, or cause detuning of RF circuits. In order to increase the probability of multipactor initiation, test facilities often employ various seeding sources such as radioactive sources (Cesium 137, Strontium 90), electron guns, or photon sources. Even with these sources, the voltage for multipactor initiation is not certain as parameters such as material type, RF pulse length, and device wall thickness can all affect seed electron flux and energy in critical gap regions, and hence the measured voltage threshold. This study investigates the effects of seed electron source type (e.g., photons versus beta particles), material type, gap size, and RF pulse length variation on multipactor threshold. In addition to the experimental work, GEANT4 simulations will be used to estimate the production rate of low energy electrons (< 5 keV) by high energy electrons and photons. A comparison of the experimental fluxes to the typical energetic photon and particle fluxes experienced by spacecraft in various orbits will also be made. Initial results indicate that for a simple, parallel plate device made of aluminum, there is no threshold variation (with seed electrons versus with no seed electrons) under continuous-wave RF exposure.

Development of the Neuron Assessment for Measuring Biology Students' Use of Experimental Design Concepts and Representations

Science.gov (United States)

Dasgupta, Annwesa P.; Anderson, Trevor R.; Pelaez, Nancy J.

2016-01-01

Researchers, instructors, and funding bodies in biology education are unanimous about the importance of developing students' competence in experimental design. Despite this, only limited measures are available for assessing such competence development, especially in the areas of molecular and cellular biology. Also, existing assessments do not…

The impact of embedded support for underprepared students in a college chemistry course

Science.gov (United States)

Hesser, Tiffany L.

This quasi-experimental study examined the impact of embedded support on academic success for students requiring remediation in college chemistry. Additional support for underprepared students incorporated within a course is recommended by Connecticut's Public Act 12-40, An Act Concerning College Readiness and Completion. For this study, embedded support consisted of weekly instructional support sessions and introduced the concepts of metacognitive awareness and motivation in learning. Students' progression through the course was measured using a series of standardized questions. Metacognitive awareness and motivation levels were measure at the start and completion of the semester using the Metacognitive Awareness Inventory (MAI) and Motivated Student Learning Questionnaire (MSLQ). It was found that with embedded support, underprepared students performed academically at a level equivalent to that of their college-ready peers. Based on these results, this embedded support model as an evidence-based practice should be considered in class development or policies surrounding students identified as underprepared.

The Experimental Measurement of Aerodynamic Heating About Complex Shapes at Supersonic Mach Numbers

Science.gov (United States)

Neumann, Richard D.; Freeman, Delma C.

2011-01-01

In 2008 a wind tunnel test program was implemented to update the experimental data available for predicting protuberance heating at supersonic Mach numbers. For this test the Langley Unitary Wind Tunnel was also used. The significant differences for this current test were the advances in the state-of-the-art in model design, fabrication techniques, instrumentation and data acquisition capabilities. This current paper provides a focused discussion of the results of an in depth analysis of unique measurements of recovery temperature obtained during the test.

Experimental measurements and finite element models of High Displacement Piezoelectric Actuators.

Science.gov (United States)

Camargo, Gilberto; Ashford, Gevale; Naco, Eris; Usher, Tim

2004-03-01

Piezoelectric actuators have many applications including morphable wing technology and piezoelectric transformers. A Piezoelectric ceramic is a material that will move when a voltage is applied and conversely produces a charge when a pressure is applied. In our study, we examine THUNDER (Thin Layer Unimorph Ferroelectric Driver and Sensor) actuators (Thunder TM is a trademark of FACE International Corporation.) Thunder actuators are constructed by bonding thin PZT piezoelectric ceramics to metal sheets. We will present physical measurements of piezoelectric actuators, as well as measurements of the displacements due to applied voltages. In our studies we used a laser micrometer to measure the dimensional characteristics of four sizes of THUNDER actuators including TH-8R, TH-9R, TH-10R, and finally the TH-11R. We also developed computer models using a commercial fine element modeling package (FEM) known as ANSYS6.0®. This software enables us to construct our models controlling such attributes as exact dimensions of the three layers of the piezoelectric actuator, the material properties of each element, the type of load that is to be applied as well as the manner in which the layers are bonded together. The computer model compares favorably with the experimental results. Acknowledgements: NASA Grant No. 0051-0078 Department of Defense (DoD) Control No.ISP02-EUG15

The relationship between experimental geometry, heat rate, and ultrasound wave speed measurement while observing phase changes in highly attenuative materials

Science.gov (United States)

Moore, David G.; Stair, Sarah L.; Jack, David A.

2018-04-01

Ultrasound techniques are capable of monitoring changes in the time-of-flight as a material is exposed to different thermal environments. The focus of the present study is to identify the phase of a material via ultrasound compression wave measurements in a through transmission experimental setup as the material is heated from a solid to a liquid and then allowed to re-solidify. The present work seeks to expand upon the authors' previous research, which proved this through transmission phase monitoring technique was possible, by considering different experimental geometries. The relationship between geometry, the measured speed of sound, and the temperature profile is presented. The use of different volumes helps in establishing a baseline understanding of which aspects of the experiment are geometry dependent and which are independent. The present study also investigates the relationship between the heating rate observed in the experiment and the measured speed of sound. The trends identified between the experimental geometry, heat rate and ultrasound wave speed measurement assist in providing a baseline understanding of the applicability of this technique to various industries, including the polymer industry and the oil industry.

Calibration of a gamma spectrometer for natural radioactivity measurement. Experimental measurements and Monte Carlo modelling

International Nuclear Information System (INIS)

Courtine, Fabien

2007-03-01

The thesis proceeded in the context of dating by thermoluminescence. This method requires laboratory measurements of the natural radioactivity. For that purpose, we have been using a germanium spectrometer. To refine the calibration of this one, we modelled it by using a Monte-Carlo computer code: Geant4. We developed a geometrical model which takes into account the presence of inactive zones and zones of poor charge-collection within the germanium crystal. The parameters of the model were adjusted by comparison with experimental results obtained with a source of 137 Cs. It appeared that the form of the inactive zones is less simple than is presented in the specialized literature. This model was widened to the case of a more complex source, with cascade effect and angular correlations between photons: the 60 Co. Lastly, applied to extended sources, it gave correct results and allowed us to validate the simulation of matrix effect. (author)

Modulation transfer function (MTF) measurement method based on support vector machine (SVM)

Science.gov (United States)

Zhang, Zheng; Chen, Yueting; Feng, Huajun; Xu, Zhihai; Li, Qi

2016-03-01

An imaging system's spatial quality can be expressed by the system's modulation spread function (MTF) as a function of spatial frequency in terms of the linear response theory. Methods have been proposed to assess the MTF of an imaging system using point, slit or edge techniques. The edge method is widely used for the low requirement of targets. However, the traditional edge methods are limited by the edge angle. Besides, image noise will impair the measurement accuracy, making the measurement result unstable. In this paper, a novel measurement method based on the support vector machine (SVM) is proposed. Image patches with different edge angles and MTF levels are generated as the training set. Parameters related with MTF and image structure are extracted from the edge images. Trained with image parameters and the corresponding MTF, the SVM classifier can assess the MTF of any edge image. The result shows that the proposed method has an excellent performance on measuring accuracy and stability.

Experimental measurements and numerical simulation of permittivity and permeability of Teflon in X band

Directory of Open Access Journals (Sweden)

Adriano Luiz de Paula

2011-01-01

Full Text Available Recognizing the importance of an adequate characterization of radar absorbing materials, and consequently their development, the present study aims to contribute for the establishment and validation of experimental determination and numerical simulation of electromagnetic materials complex permittivity and permeability, using a Teflon® sample. The present paper branches out into two related topics. The first one is concerned about the implementation of a computational modeling to predict the behavior of electromagnetic materials in confined environment by using electromagnetic three-dimensional simulation. The second topic re-examines the Nicolson-Ross-Weir mathematical model to retrieve the constitutive parameters (complex permittivity and permeability of a homogeneous sample (Teflon®, from scattering coefficient measurements. The experimental and simulated results show a good convergence that guarantees the application of the used methodologies for the characterization of different radar absorbing materials samples.

Solar intensity measurement using a thermoelectric module; experimental study and mathematical modeling

International Nuclear Information System (INIS)

Rahbar, Nader; Asadi, Amin

2016-01-01

Highlights: • Solar intensity could be explained as a linear function of voltage and ambient temperature. • The maximum output voltage is approximately 120 mV which was occurred in midday. • The average value of the heat-sink thermal resistance could be measured with this device. • The average values of total heat transfer coefficients could be measured with this device. • Two correlations were proposed to predict the solar intensity with the accuracy of 10%. - Abstract: The present study is intended to design, manufacture, and modeling an inexpensive pyranometer using a thermoelectric module. The governing equations relating the solar intensity, output voltage, and ambient temperature have been derived by applying the mathematical and thermodynamic models. According to the thermodynamics modeling, the output voltage is a function of solar intensity, ambient temperature, internal parameters of thermoelectric module, convection and radiation coefficients, and geometrical characteristics of the setup. Moreover, the solar intensity can be considered as a linear function of voltage and ambient temperature within an acceptable range of accuracy. The experiments have been carried out on a typical winter day under climatic conditions of Semnan (35°33′N, 53°23′E), Iran. The results also indicated that the output voltage is dependent on the solar intensity and its maximum value was 120 mV. Finally, based on the experimental results, two correlations, with the accuracy of 10%, have been proposed to predict the solar intensity as a function of output voltage and ambient temperature. The average values of total heat transfer coefficient and thermal resistance of the heat-sink have been also calculated according to the thermodynamic modeling and experimental results.

Measurements and Experimental Database Review for Laminar Flame Speed Premixed Ch4/Air Flames

Science.gov (United States)

Zubrilin, I. A.; Matveev, S. S.; Matveev, S. G.; Idrisov, D. V.

2018-01-01

Laminar flame speed (SL ) of CH4 was determined at atmospheric pressure and initial gas temperatures in range from 298 to 358 K. The heat flux method was employed to measure the flame speed in non-stretched flames. The kinetic mechanism GRI 3.0 [1] were used to simulate SL . The measurements were compared with available literature results. The data determined with the heat flux method agree with some previous burner measurements and disagree with the data from some vessel closed method and counterflow method. The GRI 3.0 mechanism was able to reproduce the present experiments. Laminar flame speed was determined at pressures range from of 1 to 20 atmospheres through mechanism GRI 3.0. Based on experimental data and calculations was obtained SL dependence on pressure and temperature. The resulting of dependence recommended use during the numerical simulation of methane combustion.

Experimental measurements and integrated modelling studies of actinide sorption onto cement

International Nuclear Information System (INIS)

Sugiyama, Daisuke; Fujita, Tomonari; Baston, G.M.N.

2003-01-01

An Integrated Cement Sorption Model (ICSM) for actinides onto Ordinary Portland Cement (OPC) is developed. The experimental measurements using the batch sorption technique for actinides onto cement and constituent minerals, which were considered in the modelling calculations, are also described. The actinide elements studied (thorium, uranium, neptunium, plutonium and americium) were strongly sorbed onto OPC. An initial comparison of the experimental data relating the sorption values of actinides onto cement-component phases with those onto OPC is carried out. The results suggest that the Calcium Silicate Hydrate (C-S-H) phases were found to be the most likely candidates to be the dominant-sorbing phases in order to describe the sorption of a actinides onto OPC. An approach to develop the integrated cement sorption model, based on a thermodynamic surface complexation model, is described with discussions on the possible mineralogy and phase distribution of OPC. Another approach than sorption, assuming that co-precipitation on the surface of the cement phase dominates 'sorption', is proposed and discussed. A scoring system is introduced to assess the applicability of the proposed ICSMs. It is suggested that the thermodynamic sorption model is recommended for the sorption of ionic species and the surface co-precipitation model is recommended for the sorption of neutral species though the sorption model is still recommended to be used to model OPC-based systems. (author)

Experimental design for reflection measurements of highly reactive liquid or solid substances with application to liquid sodium

International Nuclear Information System (INIS)

Chan, S.H.; Gossler, A.A.

1980-01-01

A versatile goniometer system with associated electronic components and mechanical instruments has been assembled. It is designed to measure spectral, specular reflectances of highly reactive liquid or solid substances over a spectral range of 0.3 to 9 μ and incidence angles of 12 to 30 0 off the normal direction. The capability of measuring reflectances of liquid substances clearly distinguishes this experimental design from conventional systems which are applicable only to solid substances. This design has been used to measure the spectral, specular reflectance of liquid sodium and preliminary results obtained are compared with those of solid sodium measured by other investigators

A study of calculation methodology and experimental measurements of the kinetic parameters for source driven subcritical systems

International Nuclear Information System (INIS)

Lee, Seung Min

2009-01-01

This work presents a theoretical study of reactor kinetics focusing on the methodology of calculation and the experimental measurements of the so-called kinetic parameters. A comparison between the methodology based on the Dulla's formalism and the classical method is made. The objective is to exhibit the dependence of the parameters on subcriticality level and perturbation. Two different slab type systems were considered: thermal one and fast one, both with homogeneous media. One group diffusion model was used for the fast reactor, and for the thermal system, two groups diffusion model, considering, in both case, only one precursor's family. The solutions were obtained using the expansion method. Also, descriptions of the main experimental methods of measurements of the kinetic parameters are presented in order to put a question about the compatibility of these methods in subcritical region. (author)

Fluid force predictions and experimental measurements for a magnetically levitated pediatric ventricular assist device.

Science.gov (United States)

Throckmorton, Amy L; Untaroiu, Alexandrina; Lim, D Scott; Wood, Houston G; Allaire, Paul E

2007-05-01

The latest generation of artificial blood pumps incorporates the use of magnetic bearings to levitate the rotating component of the pump, the impeller. A magnetic suspension prevents the rotating impeller from contacting the internal surfaces of the pump and reduces regions of stagnant and high shear flow that surround fluid or mechanical bearings. Applying this third-generation technology, the Virginia Artificial Heart Institute has developed a ventricular assist device (VAD) to support infants and children. In consideration of the suspension design, the axial and radial fluid forces exerted on the rotor of the pediatric VAD were estimated using computational fluid dynamics (CFD) such that fluid perturbations would be counterbalanced. In addition, a prototype was built for experimental measurements of the axial fluid forces and estimations of the radial fluid forces during operation using a blood analog mixture. The axial fluid forces for a centered impeller position were found to range from 0.5 +/- 0.01 to 1 +/- 0.02 N in magnitude for 0.5 +/- 0.095 to 3.5 +/- 0.164 Lpm over rotational speeds of 6110 +/- 0.39 to 8030 +/- 0.57% rpm. The CFD predictions for the axial forces deviated from the experimental data by approximately 8.5% with a maximum difference of 18% at higher flow rates. Similarly for the off-centered impeller conditions, the maximum radial fluid force along the y-axis was found to be -0.57 +/- 0.17 N. The maximum cross-coupling force in the x direction was found to be larger with a maximum value of 0.74 +/- 0.22 N. This resulted in a 25-35% overestimate of the radial fluid force as compared to the CFD predictions; this overestimation will lead to a far more robust magnetic suspension design. The axial and radial forces estimated from the computational results are well within a range over which a compact magnetic suspension can compensate for flow perturbations. This study also serves as an effective and novel design methodology for blood pump

Experimental validation of a new heterogeneous mechanical test design

Science.gov (United States)

Aquino, J.; Campos, A. Andrade; Souto, N.; Thuillier, S.

2018-05-01

Standard material parameters identification strategies generally use an extensive number of classical tests for collecting the required experimental data. However, a great effort has been made recently by the scientific and industrial communities to support this experimental database on heterogeneous tests. These tests can provide richer information on the material behavior allowing the identification of a more complete set of material parameters. This is a result of the recent development of full-field measurements techniques, like digital image correlation (DIC), that can capture the heterogeneous deformation fields on the specimen surface during the test. Recently, new specimen geometries were designed to enhance the richness of the strain field and capture supplementary strain states. The butterfly specimen is an example of these new geometries, designed through a numerical optimization procedure where an indicator capable of evaluating the heterogeneity and the richness of strain information. However, no experimental validation was yet performed. The aim of this work is to experimentally validate the heterogeneous butterfly mechanical test in the parameter identification framework. For this aim, DIC technique and a Finite Element Model Up-date inverse strategy are used together for the parameter identification of a DC04 steel, as well as the calculation of the indicator. The experimental tests are carried out in a universal testing machine with the ARAMIS measuring system to provide the strain states on the specimen surface. The identification strategy is accomplished with the data obtained from the experimental tests and the results are compared to a reference numerical solution.

Basic experimental preparation for the measurement of the stopping power of heavy ions in matter

International Nuclear Information System (INIS)

Carvalho Brito Brum, H. de.

1976-02-01

To measure the stopping power of heavy ions in solid matter one must develop both an experimental apparatus and a data analysis program. This thesis discusses these preparatory works and the methods to be employed. The design, building and testing of a scattering chamber with many detectors; the preparation of thin solid films, their analysis by electron diffraction and their thickness measurements; the testing of the electronic system; the calibration of the 4 MeV Van de Graaf accelerator at PUC/RJ; and the development of an original data analysis computer program are presented. (Author) [pt

Experimental evaluation of a MOSFET dosimeter for proton dose measurements

International Nuclear Information System (INIS)

Kohno, Ryosuke; Nishio, Teiji; Miyagishi, Tomoko; Hirano, Eriko; Hotta, Kenji; Kawashima, Mitsuhiko; Ogino, Takashi

2006-01-01

The metal oxide semiconductor field-effect transistor (MOSFET) dosimeter has been widely studied for use as a dosimeter for patient dose verification. The major advantage of this detector is its size, which acts as a point dosimeter, and also its ease of use. The commercially available TN502RD MOSFET dosimeter manufactured by Thomson and Nielsen has never been used for proton dosimetry. Therefore we used the MOSFET dosimeter for the first time in proton dose measurements. In this study, the MOSFET dosimeter was irradiated with 190 MeV therapeutic proton beams. We experimentally evaluated dose reproducibility, linearity, fading effect, beam intensity dependence and angular dependence for the proton beam. Furthermore, the Bragg curve and spread-out Bragg peak were also measured and the linear-energy transfer (LET) dependence of the MOSFET response was investigated. Many characteristics of the MOSFET response for proton beams were the same as those for photon beams reported in previous papers. However, the angular MOSFET responses at 45, 90, 135, 225, 270 and 315 degrees for proton beams were over-responses of about 15%, and moreover the MOSFET response depended strongly on the LET of the proton beam. This study showed that the angular dependence and LET dependence of the MOSFET response must be considered very carefully for quantitative proton dose evaluations

Self-Stabilizing Measurement of Phase

Science.gov (United States)

Vinjanampathy, Sai

2014-05-01

Measuring phase accurately constitutes one of the most important task in precision measurement science. Such measurements can be deployed to measure everything from fundamental constants to measuring detuning and tunneling rates of atoms more precisely. Quantum mechanics enhances the ultimate bounds on the precision of such measurements possible, and exploit coherence and entanglement to reduce the phase uncertainty. In this work, we will describe a method to stabilize a decohering two-level atom and use the stabilizing measurements to learn the unknown phase acquired by the atom. Such measurements will employ a Bayesian learner to do active feedback control on the atom. We will discuss some ultimate bounds employed in precision metrology and an experimental proposal for the implementation of this scheme. Financial support from Ministry of Education, Singapore.

Clathrate hydrate dissociation conditions of refrigerants R404A, R406A, R408A and R427A: Experimental measurements and thermodynamic modeling

International Nuclear Information System (INIS)

Hashemi, Hamed; Babaee, Saeedeh; Mohammadi, Amir H.; Naidoo, Paramespri; Ramjugernath, Deresh

2015-01-01

Highlights: • The application of refrigerant hydrates in cold storage systems is investigated. • Hydrate dissociation conditions of various refrigerants have been measured. • A correlative thermodynamic model was applied to the data. • Enthalpy of dissociation for the refrigerants studied calculated. • Experimental measurements performed over a wide range of pressures. - Abstract: Clathrate hydrate dissociation conditions were measured for four “alternative” refrigerants, viz. R404A, R406A, R408A and R427A. The experimental measurements were performed within the pressure range of (0.079 to 9.995) MPa and temperatures ranging from (272.7 to 288.7) K. An isochoric pressure-search method was used to perform the measurements. A thermodynamic model based on the van der Waals–Platteeuw (vdW–P) model was applied for the prediction of the dissociation conditions which were compared to the experimental measurements. The fluid phase was modeled using the MHV2 G E -EoS mixing rule along with the UNIFAC (original) activity model. The van der Waals–Platteeuw (vdW–P) model was used for the modeling of the hydrate phase. There was reasonable agreement between the experimental and predicted values

Measurement of transepidermal water loss (TEWL) in cats with experimental skin barrier dysfunction using a closed chamber system.

Science.gov (United States)

Momota, Yutaka; Shimada, Kenichiro; Gin, Azusa; Matsubara, Takako; Azakami, Daigo; Ishioka, Katsumi; Nakamura, Yuka; Sako, Toshinori

2016-10-01

A closed chamber evaporimeter is suitable for measuring transepidermal water loss (TEWL) in cats because of the compact device size, tolerance to sudden movement and short measuring time. TEWL is a representative parameter for skin barrier dysfunction, which is one of the clinical signs of atopic dermatitis in humans and dogs. Measurement of feline TEWL has been reported, but applicability of this parameter has not been validated. The aims of this study were to determine if tape stripping is a valid experimental model in cats for studying TEWL and to determine if a closed chambered system is a suitable measurement tool for cats. Ten clinically normal cats. In order to evaluate variation of the measured values, TEWL was measured at the right and left side of the three clipped regions (axillae, lateral thigh and groin). Subsequently, TEWL was measured using sequential tape stripping of the stratum corneum as a model of acute barrier disruption. The variations between both sides of the three regions showed no significant difference. Sequential tape stripping was associated with increasing values for TEWL. Feline TEWL was shown to reflect changes in the skin barrier in an experimental model using a closed chamber system and has the potential for evaluating skin barrier function in cats with skin diseases. © 2016 ESVD and ACVD.

Supporting 3rd-grade students model-based explanations about groundwater: a quasi-experimental study of a curricular intervention

Science.gov (United States)

Zangori, Laura; Vo, Tina; Forbes, Cory T.; Schwarz, Christina V.

2017-07-01

Scientific modelling is a key practice in which K-12 students should engage to begin developing robust conceptual understanding of natural systems, including water. However, little past research has explored primary students' learning about groundwater, engagement in scientific modelling, and/or the ways in which teachers conceptualise and cultivate model-based science learning environments. We are engaged in a multi-year project designed to support 3rd-grade students' formulation of model-based explanations (MBE) for hydrologic phenomenon, including groundwater, through curricular and instructional support. In this quasi-experimental comparative study of five 3rd-grade classrooms, we present findings from analysis of students' MBE generated as part of experiencing a baseline curricular intervention (Year 1) and a modelling-enhanced curricular intervention (Year 2). Findings show that students experiencing the latter version of the unit made significant gains in both conceptual understanding and reasoning about groundwater, but that these gains varied by classroom. Overall, student gains from Year 1 to Year 2 were attributed to changes in two of the five classrooms in which students were provided additional instructional supports and scaffolds to enhance their MBE for groundwater. Within these two classrooms, the teachers enacted the Year 2 curriculum in unique ways that reflected their deeper understanding about the practices of modelling. Their enactments played a critical role in supporting students' MBE about groundwater. Study findings contribute to research on scientific modelling in elementary science learning environments and have important implications for teachers and curriculum developers.

Carbon Isotope Measurements of Experimentally-Derived Hydrothermal Mineral-Catalyzed Organic Products by Pyrolysis-Isotope Ratio Mass Spectrometry

Science.gov (United States)

Socki, Richard A.; Fu, Qi; Niles, Paul B.

2011-01-01

We report results of experiments to measure the C isotope composition of mineral catalyzed organic compounds derived from high temperature and high pressure synthesis. These experiments make use of an innovative pyrolysis technique designed to extract and measure C isotopes. To date, our experiments have focused on the pyrolysis and C isotope ratio measurements of low-molecular weight intermediary hydrocarbons (organic acids and alcohols) and serve as a proof of concept for making C and H isotope measurements on more complicated mixtures of solid-phase hydrocarbons and intermediary products produced during high temperature and high pressure synthesis on mineral-catalyzed surfaces. The impetus for this work stems from recently reported observations of methane detected within the Martian atmosphere [1-4], coupled with evidence showing extensive water-rock interaction during Martian history [5-7]. Methane production on Mars could be the result of synthesis by mineral surface-catalyzed reduction of CO2 and/or CO by Fischer-Tropsch Type (FTT) reactions during serpentization reactions [8,9]. Others have conducted experimental studies to show that FTT reactions are plausible mechanisms for low-molecular weight hydrocarbon formation in hydrothermal systems at mid-ocean ridges [10-12]. Further, recent experiments by Fu et al. [13] focus on examining detailed C isotope measurements of hydrocarbons produced by surface-catalyzed mineral reactions. Work described in this paper details the experimental techniques used to measure intermediary organic reaction products (alcohols and organic acids).

Water reactor fuel element modelling at high burnup and its experimental support. Proceedings of a technical committee meeting

International Nuclear Information System (INIS)

1997-08-01

The Technical Committee Meeting on Fuel Element Modelling at High Burnup and its Experimental Support was recommended by the International Working Group on Fuel Performance and Technology (IWGFPT). Its subject had been touched on in many of the IAEA's activities; however for the first time modellers and experimentalists were brought together to have an exchange of views on the research under way and to identify areas where new knowledge is necessary to improve the safety, reliability and/or economics of nuclear fuel. The timely organization of this meeting in conjunction with the second meeting of the Co-ordinated Research Programme on Fuel Modelling at Extended Burnup, in short ''FUMEX'', allowed fruitful participation of representatives of developing countries which are only rarely exposed to such a scientific event. The thirty-nine papers presented covered the status of codes and experimental facilities and the main phenomena affecting the fuel during irradiation, namely: thermal fuel performance, clad corrosion and pellet-cladding interaction (PCI) and fission gas release (FGR). Refs, figs, tabs

Water reactor fuel element modelling at high burnup and its experimental support. Proceedings of a technical committee meeting

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-08-01

The Technical Committee Meeting on Fuel Element Modelling at High Burnup and its Experimental Support was recommended by the International Working Group on Fuel Performance and Technology (IWGFPT). Its subject had been touched on in many of the IAEA`s activities; however for the first time modellers and experimentalists were brought together to have an exchange of views on the research under way and to identify areas where new knowledge is necessary to improve the safety, reliability and/or economics of nuclear fuel. The timely organization of this meeting in conjunction with the second meeting of the Co-ordinated Research Programme on Fuel Modelling at Extended Burnup, in short ``FUMEX``, allowed fruitful participation of representatives of developing countries which are only rarely exposed to such a scientific event. The thirty-nine papers presented covered the status of codes and experimental facilities and the main phenomena affecting the fuel during irradiation, namely: thermal fuel performance, clad corrosion and pellet-cladding interaction (PCI) and fission gas release (FGR). Refs, figs, tabs.

Methodology and experimental setup for measuring short-lives fission product yields in actinides induced fission by charged particles

International Nuclear Information System (INIS)

Bellido, A.V.

1995-07-01

The theoretical principles and the laboratory set-up for the fission products yields measurements are described. The procedures for the experimental determinations are explain in detail. (author). 43 refs., 5 figs

Experimental study of a variable-capacitance micromotor with electrostatic suspension

International Nuclear Information System (INIS)

Han, F T; Wu, Q P; Wang, L

2010-01-01

A variable-capacitance micromotor where the rotor is supported electrostatically in five degrees of freedom was designed, fabricated and tested in order to study the behavior of this electrostatic motor. The micromachined device is based on a glass/silicon/glass stack bonding structure, fabricated by bulk micromachining and initially operated in atmospheric environment. The analytical torque model is obtained by calculating the capacitances between different stator electrodes and the rotor. Capacitance values in the order of 10 −13 pF and torque values in the order of 10 −10 N m have been calculated from the motor geometry and attainable drive voltage. A dynamic model of the motor is proposed by further estimating the air-film damping effect in an effort to explain the experimental rotation measurements. Experimental results of starting voltage, continuous operation, switching response and electric bearing of the micromotor are presented and discussed. Preliminary measurements indicate that a rotor rotating speed of 73.3 r min −1 can be achieved at a drive voltage of 28.3 V, equivalent to a theoretical motive torque of 517 pN m. Starting voltage results obtained from experimental measurement are in agreement with the developed dynamic model

Experimental Investigation for Fault Diagnosis Based on a Hybrid Approach Using Wavelet Packet and Support Vector Classification

Directory of Open Access Journals (Sweden)

Pengfei Li

2014-01-01

Full Text Available To deal with the difficulty to obtain a large number of fault samples under the practical condition for mechanical fault diagnosis, a hybrid method that combined wavelet packet decomposition and support vector classification (SVC is proposed. The wavelet packet is employed to decompose the vibration signal to obtain the energy ratio in each frequency band. Taking energy ratios as feature vectors, the pattern recognition results are obtained by the SVC. The rolling bearing and gear fault diagnostic results of the typical experimental platform show that the present approach is robust to noise and has higher classification accuracy and, thus, provides a better way to diagnose mechanical faults under the condition of small fault samples.

Novel experimental measuring techniques required to provide data for CFD validation

International Nuclear Information System (INIS)

Prasser, H.-M.

2008-01-01

CFD code validation requires experimental data that characterize the distributions of parameters within large flow domains. On the other hand, the development of geometry-independent closure relations for CFD codes have to rely on instrumentation and experimental techniques appropriate for the phenomena that are to be modelled, which usually requires high spatial and time resolution. The paper reports about the use of wire-mesh sensors to study turbulent mixing processes in single-phase flow as well as to characterize the dynamics of the gas-liquid interface in a vertical pipe flow. Experiments at a pipe of a nominal diameter of 200 mm are taken as the basis for the development and test of closure relations describing bubble coalescence and break-up, interfacial momentum transfer and turbulence modulation for a multi-bubble-class model. This is done by measuring the evolution of the flow structure along the pipe. The transferability of the extended CFD code to more complicated 3D flow situations is assessed against measured data from tests involving two-phase flow around an asymmetric obstacle placed in a vertical pipe. The obstacle, a half-moon-shaped diaphragm, is movable in the direction of the pipe axis; this allows the 3D gas fraction field to be recorded without changing the sensor position. In the outlook, the pressure chamber of TOPFLOW is presented, which will be used as the containment for a test facility, in which experiments can be conducted in pressure equilibrium with the inner atmosphere of the tank. In this way, flow structures can be observed by optical means through large-scale windows even at pressures of up to 5 MPa. The so-called 'Diving Chamber' technology will be used for Pressurized Thermal Shock (PTS) tests. Finally, some important trends in instrumentation for multi-phase flows will be given. This includes the state-of-art of X-ray and gamma tomography, new multi-component wire-mesh sensors, and a discussion of the potential of other non

Novel experimental measuring techniques required to provide data for CFD validation

International Nuclear Information System (INIS)

Prasser, H.M.

2007-01-01

CFD code validation requires experimental data that characterize distributions of parameters within large flow domains. On the other hand, the development of geometry-independent closure relations for CFD codes have to rely on instrumentation and experimental techniques appropriate for the phenomena that are to be modelled, which usually requires high spatial and time resolution. The presentation reports about the use of wire-mesh sensors to study turbulent mixing processes in the single-phase flow as well as to characterize the dynamics of the gas-liquid interface in a vertical pipe flow. Experiments at a pipe of a nominal diameter of 200 mm are taken as the basis for the development and test of closure relations describing bubble coalescence and break-up, interfacial momentum transfer and turbulence modulation for a multi-bubble-class model. This is done by measuring the evolution of the flow structure along the pipe. The transferability of the extended CFD code to more complicated 3D flow situations is assessed against measured data from tests involving two-phase flow around an asymmetric obstacle placed in a vertical pipe. The obstacle, a half-moon-shaped diaphragm, is movable in the direction of the pipe axis; this allows the 3D gas fraction field to be recorded without changing the sensor position. In the outlook, the pressure chamber of TOPFLOW is presented, which will be used as the containment for a test facility, in which experiments can be conducted in pressure equilibrium with the inner atmosphere of the tank. In this way, flow structures can be observed by optical means through large-scale windows even at pressures of up to 5 MPa. The so-called 'Diving Chamber' technology will be used for Pressurized Thermal Shock (PTS) tests. Finally, some important trends in instrumentation for multi-phase flows will be given. This includes the state-of-art of X-ray and gamma tomography, new multi-component wire-mesh sensors, and a discussion of the potential of

Constitutive modelling of an arterial wall supported by microscopic measurements

Directory of Open Access Journals (Sweden)

Vychytil J.

2012-06-01

Full Text Available An idealized model of an arterial wall is proposed as a two-layer system. Distinct mechanical response of each layer is taken into account considering two types of strain energy functions in the hyperelasticity framework. The outer layer, considered as a fibre-reinforced composite, is modelled using the structural model of Holzapfel. The inner layer, on the other hand, is represented by a two-scale model mimicing smooth muscle tissue. For this model, material parameters such as shape, volume fraction and orientation of smooth muscle cells are determined using the microscopic measurements. The resulting model of an arterial ring is stretched axially and loaded with inner pressure to simulate the mechanical response of a porcine arterial segment during inflation and axial stretching. Good agreement of the model prediction with experimental data is promising for further progress.

Impact of engaging middle management in practice interventions on staff support and learning culture: a quasi-experimental design.

Science.gov (United States)

Henderson, Amanda; Burmeister, Liz; Schoonbeek, Sue; Ossenberg, Christine; Gneilding, Julieanne

2014-11-01

This study evaluated the impact of different levels of engaging middle management in ward based strategies implemented by a project educator. The challenge for learning in practice is to develop effective teams where experienced staff engage and foster learning with students and other novice staff. A quasi-experimental pre- and post- intervention four group design was conducted from November 2009 to May 2010 across four general surgical and four general medical inpatient matched units in two settings in South East Queensland, Australia. Staff survey data was used to compare control and intervention groups (one actively engaging nurse managers) before and after 'practice learning' interventions. The survey comprised demographic data and data from two validated scales (support instrument for nurses facilitating learning and clinical learning organisational culture). Number of surveys returned pre- and post-intervention was 336 from 713 (47%). There were significant differences across many subscales pertaining to staff perception of support in the intervention groups, with only one change in the control group. The number of significant different subscales in the learning culture was also greater when middle management supported the intervention. Middle management should work closely with facilitators to assist embedding practice interventions. © 2013 John Wiley & Sons Ltd.

Quark deconfinement in nuclei: A review of experimental tests based on nuclear magnetic moment measurements

International Nuclear Information System (INIS)

Stone, N.J.; Rikovska, J.

1988-01-01

The introduction very briefly outlines the basic idea and experimental evidence to suggest that quarks may behave differently in nuclei and in individual nucleons, with possible consequences for the calculation of nuclear magnetic dipole moments. After description of a calculation of moments made using the extreme model of total quark deconfinement (the MIT bag model) attention is focussed on experimental tests and the state of current evidence for more partial quark deconfinement. The arguments of Yamazaki which give an experimental basis for distinguishing quark deconfinement effects from, specifically, effects caused by pion exchange currents, are given in more detail. The reasons underlying choice of nuclei in which meaningful tests may be possible are given. Early claims by Karl et al. to have demonstrated the existence of quark deconfinement in mass 3 nuclei are discussed. The current status of evidence for deconfinement based on orbital g-factor measurements in heavier nuclei is also summarised. Finally some examples are given of possible experiments using recently developed on-line facilities which may provide further tests of these ideas. (orig.)

A new experimental apparatus for emissivity measurements of steel and the application of multi-wavelength thermometry to continuous casting billets

Science.gov (United States)

Wang, Peng; Hu, Zhenwei; Xie, Zhi; Yan, Ming

2018-05-01

An experimental apparatus has been designed for measuring the emissivity of a steel surface in both vacuum and oxidation atmosphere. The sample is heated with the method of electromagnetic induction in order to ensure the temperature uniformity. The radiance emitted from a sample is measured using a fiber-optic Fourier transform infrared spectrometer. Using this unique apparatus, we investigated the spectral (2-6 μm) and directional (0°-86°) emissivity of stainless steel 304 with different degrees of surface oxidation at temperatures ranging from 800 to 1100 °C. The experimental results show that the emissivity increases slightly with increasing temperature, which accords with the Hagen-Rubens relation. The emissivity increases rapidly at the initial stage of oxidation, but gradually reaches to a constant value after 20 min. In addition, the directional emissivity has a maximum value at the measuring angle of about 75°. The maximum uncertainty of emissivity is only 3.0% over all the measuring ranges, indicating that this experimental apparatus has a high reliability. In order to measure the surface temperature of casting billets based on multi-wavelength thermometry, the bivariate emissivity function with the two variables, wavelength and temperature, is determined. Temperature measurement results based on our technique are compared with those from common dual-wavelength radiation thermometry. Our approach reduces the measured temperature fluctuation from ±20.7 °C to ±2.8 °C and reflects the temperature variation with the changes of production parameters in real time.

Impact of a Plant-Based Diet and Support on Mitigating Type 2 Diabetes Mellitus in Latinos Living in Medically Underserved Areas.

Science.gov (United States)

Ramal, Edelweiss; Champlin, Andrea; Bahjri, Khaled

2018-03-01

To determine the impact that a high-fiber, low-fat diet, derived from mostly plant-based sources, when coupled with support has upon self-management of type 2 diabetes mellitus in Latinos from medically underserved areas (MUAs). Experimental randomized controlled community pilot study. Three community clinics in MUAs located within San Bernardino County, California. Thirty-two randomly assigned Latinos with A1 C greater than 6.4: 15 control and 17 experimental. Participants completed a 5-week education program. Researchers provided follow-up support for 17 randomly assigned experimental group participants through focus groups held at participating clinics-1, 3, and 6 months posteducation. Changes in fat and fiber consumption were measured using a modified Dietary Screener for Mexican Americans. Self-management was measured through the Self-Efficacy for Exercise Scale and Diabetes Quality of Life Measure. Baseline characteristics for both groups were analyzed using independent t tests and χ 2 tests. A 2-way repeated-measures analysis of variance was used to analyze biometric data between baseline and 6 months for both groups. Mean A1 C levels decreased from baseline to 6 months for both groups: control, μ 1 = 9.57, μ 2 = 9.49; experimental, μ 1 = 8.53, μ 2 = 7.31. The experimental group demonstrated a statistically significant reduction in mean A1 C levels ( P = .002) when compared to the control group.

Experimental set-up for electrical resistivity measurements at low temperature in amorphous and crystalline metallic samples

International Nuclear Information System (INIS)

Rodriquez Fernandez, J.M.; Lopez Sanchez, R.J.; Gomez-Sal, J.C.

1986-01-01

The experimental set-up to measure the thermal variation of the electrical resistivity between 10.5 K and 300 K, has been developed. A four probe A.C. method with a synchronous-detection (lock'in) technique were the idoneous for our proposes. We have designed a new type of pressure sample-holder adopted to the CS-202 type cryostat. The measurements performed on samples already known have allowed us to determine the sensitivity of our experiments, which is Δ ρ/ρ=2x10 -4 . The measurements performed in the new Y 3 Rh 2 Si 2 compound which at 10 K has no magnetic ordering, are also presented. (author)

Parametric instabilities of rotor-support systems with application to industrial ventilators

Science.gov (United States)

Parszewski, Z.; Krodkiemski, T.; Marynowski, K.

1980-01-01

Rotor support systems interaction with parametric excitation is considered for both unequal principal shaft stiffness (generators) and offset disc rotors (ventilators). Instability regions and types of instability are computed in the first case, and parametric resonances in the second case. Computed and experimental results are compared for laboratory machine models. A field case study of parametric vibrations in industrial ventilators is reported. Computed parametric resonances are confirmed in field measurements, and some industrial failures are explained. Also the dynamic influence and gyroscopic effect of supporting structures are shown and computed.

Experimental testing of the digital multichannel analyzer for gamma spectrometry measurements

International Nuclear Information System (INIS)

Novkovic, D.; Nadjdjerdj, L.; Kandic, A.; Vukanac, I.; Djurasevic, M.

2008-01-01

The results of experimental testing of the digital multichannel analyzer which digitalizes the signal after a preamplifier are presented. The recordings of some of the characteristics of the spectrometer containing a digital MCA, such as full-peak efficiency, net-area ratio of the two peaks and the stability of the peak position, were carried out under different input counting rates, with different radioactive sources. The tested MCA has shown some excellent features, like the stability of the peak position over a long-term period and flexibility in the adjusting of optimum measurement conditions. However, the performed tests have also shown some serious and unexpected disadvantages of the digital MCA when it operates under certain circumstances, one of them having to do with the automatic tuning of live-time correction at low-input counting rates. (author)

Experimental setup and procedure for the measurement of the {sup 7}Be(n,α)α reaction at n-TOF

Energy Technology Data Exchange (ETDEWEB)

Cosentino, L. [INFN Laboratori Nazionali del Sud, Catania (Italy); Musumarra, A. [INFN Laboratori Nazionali del Sud, Catania (Italy); Dipartimento di Fisica e Astronomia DFA, Università di Catania (Italy); Barbagallo, M. [INFN Sezione di Bari (Italy); Pappalardo, A. [INFN Laboratori Nazionali del Sud, Catania (Italy); Colonna, N.; Damone, L. [INFN Sezione di Bari (Italy); Piscopo, M. [INFN Laboratori Nazionali del Sud, Catania (Italy); Finocchiaro, P., E-mail: FINOCCHIARO@LNS.INFN.IT [INFN Laboratori Nazionali del Sud, Catania (Italy); Maugeri, E.; Heinitz, S.; Schumann, D.; Dressler, R.; Kivel, N. [Paul Scherrer Institut, Nuclear Energy and Safety Research Department, 5232 Villigen (Switzerland); Aberle, O. [CERN, Geneva (Switzerland); Andrzejewski, J. [Uniwersytet Łódzki, Lodz (Poland); Audouin, L. [Institut de Physique Nucléaire, CNRS-IN2P3, Univ. Paris-Sud, Université Paris-Saclay, 91406 Orsay Cedex (France); Ayranov, M. [European Commission, DG-Energy (Luxembourg); Bacak, M. [Atominstitut der Österreichischen Universitäten, Technische Universität Wien (Austria); Barros, S. [C2TN-Instituto Superior Tecníco, Universidade de Lisboa (Portugal); Balibrea-Correa, J. [Centro de Investigaciones Energeticas Medioambientales y Tecnológicas (CIEMAT), Madrid (Spain); and others

2016-09-11

The newly built second experimental area EAR2 of the n-TOF spallation neutron source at CERN allows to perform (n, charged particles) experiments on short-lived highly radioactive targets. This paper describes a detection apparatus and the experimental procedure for the determination of the cross-section of the {sup 7}Be(n,α)α reaction, which represents one of the focal points toward the solution of the cosmological Lithium abundance problem, and whose only measurement, at thermal energy, dates back to 1963. The apparently unsurmountable experimental difficulties stemming from the huge {sup 7}Be γ-activity, along with the lack of a suitable neutron beam facility, had so far prevented further measurements. The detection system is subject to considerable radiation damage, but is capable of disentangling the rare reaction signals from the very high background. This newly developed setup could likely be useful also to study other challenging reactions requiring the detectors to be installed directly in the neutron beam.

Direct Measurements of Quantum Kinetic Energy Tensor in Stable and Metastable Water near the Triple Point: An Experimental Benchmark.

Science.gov (United States)

Andreani, Carla; Romanelli, Giovanni; Senesi, Roberto

2016-06-16

This study presents the first direct and quantitative measurement of the nuclear momentum distribution anisotropy and the quantum kinetic energy tensor in stable and metastable (supercooled) water near its triple point, using deep inelastic neutron scattering (DINS). From the experimental spectra, accurate line shapes of the hydrogen momentum distributions are derived using an anisotropic Gaussian and a model-independent framework. The experimental results, benchmarked with those obtained for the solid phase, provide the state of the art directional values of the hydrogen mean kinetic energy in metastable water. The determinations of the direction kinetic energies in the supercooled phase, provide accurate and quantitative measurements of these dynamical observables in metastable and stable phases, that is, key insight in the physical mechanisms of the hydrogen quantum state in both disordered and polycrystalline systems. The remarkable findings of this study establish novel insight into further expand the capacity and accuracy of DINS investigations of the nuclear quantum effects in water and represent reference experimental values for theoretical investigations.

The stress-buffering effects of functional social support on ambulatory blood pressure.

Science.gov (United States)

Bowen, Kimberly S; Uchino, Bert N; Birmingham, Wendy; Carlisle, McKenzie; Smith, Timothy W; Light, Kathleen C

2014-11-01

Social support is a reliable predictor of cardiovascular health. According to the buffering hypothesis, stress is 1 mechanism by which support is able to affect physiological processes. However, most of the experimental evidence for the hypothesis comes from laboratory studies. Ambulatory blood pressure (ABP) protocols examine participants in their natural environment, where they are more likely to encounter personally relevant real-world stressors. Furthermore, prior work shows that examining support by its specific functional components reveals additional independent links to health. The current study aimed to examine the stress-buffering effects of functional social support on ABP. One hundred eighty-eight participants completed a 1-day ABP assessment along with measures of functional social support and both global perceived stress and momentary stress at time of reading. RESULTS indicated main effects for both stress measures. Global support, emotional, tangible, and informational support only moderated the effects of momentary stress, but not global stress, in predicting ABP. Informational support was the most consistent stress-buffering predictor of ABP, predicting both ambulatory systolic and diastolic blood pressure. The predicted values in ABP for informational support achieved health-relevant differences, emphasizing the value of examining functional support beyond global support alone. PsycINFO Database Record (c) 2014 APA, all rights reserved.

Experimental validation of alternate integral-formulation method for predicting acoustic radiation based on particle velocity measurements.

Science.gov (United States)

Ni, Zhi; Wu, Sean F

2010-09-01

This paper presents experimental validation of an alternate integral-formulation method (AIM) for predicting acoustic radiation from an arbitrary structure based on the particle velocities specified on a hypothetical surface enclosing the target source. Both the normal and tangential components of the particle velocity on this hypothetical surface are measured and taken as the input to AIM codes to predict the acoustic pressures in both exterior and interior regions. The results obtained are compared with the benchmark values measured by microphones at the same locations. To gain some insight into practical applications of AIM, laser Doppler anemometer (LDA) and double hotwire sensor (DHS) are used as measurement devices to collect the particle velocities in the air. Measurement limitations of using LDA and DHS are discussed.

Experimental investigation on local parameter measurement using optical probes in two-phase flow under rolling condition

International Nuclear Information System (INIS)

Tian Daogui; Sun Licheng; Yan Changqi; Liu Guoqiang

2013-01-01

In order to get more local interfacial information as well as to further comprehend the intrinsic mechanism of two-phase flow under rolling condition, a method was proposed to measure the local parameters by using optical probes under rolling condition in this paper. An experimental investigation of two-phase flow under rolling condition was conducted using the probe fabricated by the authors. It is verified that the probe method is feasible to measure the local parameters in two'-phase flow under rolling condition. The results show that the interfacial parameters distribution near wall region has a distinct periodicity due to the rolling motion. The averaged deviation of the void fraction measured by the probe from that obtained from measured pressure drop is about 8%. (authors)

Experimental Investigation of the Effect of Natural Convevtion on Heat Transfer in Mineral Wool

DEFF Research Database (Denmark)

Dyrbøl, Susanne; Svendsen, Svend; Elmroth, Arne

2002-01-01

from 0.1 to 0.5 m. The contribution of natural convection to the total heat transfer has been experimentally examined for 'perfectly' installed fibrous materials of different air-flow permeability and thermal conductivity. To support the interpretation of the measurements, the experimental work has......In Denmark and a number of other countries convection in fibrous materials is considered non-existent when calculating heat transmission as well as when designing building structures. The current investigation serves to examine whether considering natural convection non-existent in fibrous...... been supplemented with numerical calculations. The measurements and the concurrent computations both show a clear convection-induced redistribution of the heat flow in the material. When measured from the hot side in the apparatus this occurs in the form of an increased heat flow, primarily through...

A preliminary investigation of a new pictorial method of measuring aggression-supportive cognition among young aggressive males.

Science.gov (United States)

Hutchings, Jade N; Gannon, Theresa A; Gilchrist, Elizabeth

2010-04-01

A new pictorial assessment was developed to measure aggression-supportive cognitions among young aggressive male students. The assessment was comprised of 17 watercolor ambiguous sketches that could be interpreted in either an aggressive or a benign manner (e.g., two young people facing each other with their arms folded). The results showed that high trait aggressive male students were more likely to make hostile attributions of the pictures, providing significantly more themes of entitlement and power in the stories they generated about the pictures. Aggressive male students also endorsed significantly more aggression-supportive cognitions on a self-report measure and provided some supporting qualitative accounts of physically aggressive encounters. The results of this study are discussed and evaluated with reference to future work with young violent adolescents.

Three experimental tests of Bell's inequalities by measurement of polarization correlation of photons

International Nuclear Information System (INIS)

Aspect, A.

1983-02-01

We have performed three experimental tests of Bell's inequalities by measuring the linear-polarization correlation of photons emitted by pairs in the 4p 2 1 S 0 → 4s4p 1 P 1 → 4s 2 1 S 0 radiative cascade of calcium. The first part of this dissertation reminds the theoretical background (Bell's theorem), and the experimental situation (previous experiments). We then describe our apparatus: the source (calcium atomic beam selectively excited by two-photon absorption), the optics, the photon coincidence-counting system. Our first experiment, analogous to previous ones (but more precise) involves one-channel polarizers. Our second experiment, based on a conceptually simpler scheme, uses two-channel polarizers. The third experiment involves acousto-optical switches followed by two linear polarizers: these devices act as time-varying polarizers, the orientation of which is changed during the time of flight of photons. In the three experiments, the results are in good agreement with the Quantum mechanical predictions, and they distinctly violate the relevant Bell's inequalities [fr

Keeping the Spirits Up: The Effect of Teachers’ and Parents’ Emotional Support on Children’s Working Memory Performance

Science.gov (United States)

Vandenbroucke, Loren; Spilt, Jantine; Verschueren, Karine; Baeyens, Dieter

2017-01-01

Working memory, used to temporarily store and mentally manipulate information, is important for children’s learning. It is therefore valuable to understand which (contextual) factors promote or hinder working memory performance. Recent research shows positive associations between positive parent–child and teacher–student interactions and working memory performance and development. However, no study has yet experimentally investigated how parents and teachers affect working memory performance. Based on attachment theory, the current study investigated the role of parent and teacher emotional support in promoting working memory performance by buffering the negative effect of social stress. Questionnaires and an experimental session were completed by 170 children from grade 1 to 2 (Mage = 7 years 6 months, SD = 7 months). Questionnaires were used to assess children’s perceptions of the teacher–student and parent–child relationship. During an experimental session, working memory was measured with the Corsi task backward (Milner, 1971) in a pre- and post-test design. In-between the tests stress was induced in the children using the Cyberball paradigm (Williams et al., 2000). Emotional support was manipulated (between-subjects) through an audio message (either a weather report, a supportive message of a stranger, a supportive message of a parent, or a supportive message of a teacher). Results of repeated measures ANOVA showed no clear effect of the stress induction. Nevertheless, an effect of parent and teacher support was found and depended on the quality of the parent–child relationship. When children had a positive relationship with their parent, support of parents and teachers had little effect on working memory performance. When children had a negative relationship with their parent, a supportive message of that parent decreased working memory performance, while a supportive message from the teacher increased performance. In sum, the current study

Experimental measurement and modeling of snow accumulation and snowmelt in a mountain microcatchment

Science.gov (United States)

Danko, Michal; Krajčí, Pavel; Hlavčo, Jozef; Kostka, Zdeněk; Holko, Ladislav

2016-04-01

Fieldwork is a very useful source of data in all geosciences. This naturally applies also to the snow hydrology. Snow accumulation and snowmelt are spatially very heterogeneous especially in non-forested, mountain environments. Direct field measurements provide the most accurate information about it. Quantification and understanding of processes, that cause these spatial differences are crucial in prediction and modelling of runoff volumes in spring snowmelt period. This study presents possibilities of detailed measurement and modeling of snow cover characteristics in a mountain experimental microcatchment located in northern part of Slovakia in Western Tatra mountains. Catchment area is 0.059 km2 and mean altitude is 1500 m a.s.l. Measurement network consists of 27 snow poles, 3 small snow lysimeters, discharge measurement device and standard automatic weather station. Snow depth and snow water equivalent (SWE) were measured twice a month near the snow poles. These measurements were used to estimate spatial differences in accumulation of SWE. Snowmelt outflow was measured by small snow lysimeters. Measurements were performed in winter 2014/2015. Snow water equivalent variability was very high in such a small area. Differences between particular measuring points reached 600 mm in time of maximum SWE. The results indicated good performance of a snow lysimeter in case of snowmelt timing identification. Increase of snowmelt measured by the snow lysimeter had the same timing as increase in discharge at catchment's outlet and the same timing as the increase in air temperature above the freezing point. Measured data were afterwards used in distributed rainfall-runoff model MIKE-SHE. Several methods were used for spatial distribution of precipitation and snow water equivalent. The model was able to simulate snow water equivalent and snowmelt timing in daily step reasonably well. Simulated discharges were slightly overestimated in later spring.

Experimental Evaluation of Grid Support Enabled PV Inverter Response to Abnormal Grid Conditions: Preprint

Energy Technology Data Exchange (ETDEWEB)

Nelson, Austin; Martin, Gregory; Hurtt, James

2017-05-08

As revised interconnection standards for grid-tied photovoltaic (PV) inverters address new advanced grid support functions (GSFs), there is increasing interest in inverter performance in the case of abnormal grid conditions. The growth of GSF-enabled inverters has outpaced the industry standards that define their operation, although recently published updates to UL1741 with Supplement SA define test conditions for GSFs such as volt-var control, frequency-watt control, and volt-age/frequency ride-through, among others. A comparative experimental evaluation has been completed on four commercially available, three-phase PV inverters in the 24.0-39.8 kVA power range on their GSF capability and the effect on abnormal grid condition response. This study examines the impact particular GSF implementations have on run-on times during islanding conditions, peak voltages in load rejection overvoltage scenarios, and peak currents during single-phase and three-phase fault events for individual inverters. This report reviews comparative test data, which shows that GSFs have little impact on the metrics of interest in most tests cases.

Experimental measurements of U24Py nanocluster behavior in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Flynn, Shannon L.; Szymanowski, Jennifer E.S.; Fein, Jeremy B. [Univ. of Notre Dame, IN (United States). Department of Civil and Environmental Engineering and Earth Sciences; Dembowski, Mateusz [Univ. of Notre Dame, IN (United States). Department of Chemistry and Biochemistry; Burns, Peter C. [Univ. of Notre Dame, IN (United States). Department of Civil and Environmental Engineering and Earth Sciences; Univ. of Notre Dame, IN (United States). Department of Chemistry and Biochemistry

2016-07-01

Uranyl peroxide nanoclusters may impact the mobility and partitioning of uranium at contaminated sites and could be used in the isolation of uranium during the reprocessing of nuclear waste. Their behavior in aqueous systems must be better understood to predict the environmental fate of uranyl peroxide nanoclusters and for their use in engineered systems. The aqueous stability of only one uranyl peroxide nanocluster, U60 (K{sub 16}Li{sub 44}[UO{sub 2}(O{sub 2})OH]{sub 60}), has been studied to date [Flynn, S. L., Szymanowski, J. E. S., Gao, Y., Liu, T., Burns, P. C., Fein, J. B.: Experimental measurements of U60 nanocluster stability in aqueous solution. Geochemica et Cosmochimica Acta 156, 94-105 (2015)]. In this study, we measured the aqueous stability of a second uranyl peroxide nanocluster, U24Py (Na{sub 30}[(UO{sub 2}){sub 24}(O{sub 2}){sub 24}(HP{sub 2}O{sub 7}){sub 6}(H{sub 2}P{sub 2}O{sub 7}){sub 6}]), in batch systems as a function of time, pH, and nanocluster concentration, and then compared the aqueous behavior of U24Py to U60 to determine whether the size and morphology differences result in differences in their aqueous behaviors. Systems containing U24Py nanoclusters took over 30 days to achieve steady-state concentrations of monomeric U, Na, and P, illustrating slower reaction kinetics than parallel U60 systems. Furthermore, U24Py exhibited lower stability in solution than U60, with an average of 72% of the total mass in each nanocluster suspension being associated with the U24Py nanocluster, whereas 97% was associated with the U60 nanocluster in parallel experiments [Flynn, S. L., Szymanowski, J. E. S., Gao, Y., Liu, T., Burns, P. C., Fein, J. B.: Experimental measurements of U60 nanocluster stability in aqueous solution. Geochemica et Cosmochimica Acta 156, 94-105 (2015)]. The measurements from the batch experiments were used to calculate ion activity product (IAP) values for the reaction between the U24Py nanocluster and its constituent monomeric

Experimental test of magnetic photons

International Nuclear Information System (INIS)

Lakes, R.S.

2004-01-01

A 'magnetic' photon hypothesis associated with magnetic monopoles is tested experimentally. These photons are predicted to easily penetrate metal. Experimentally the optical transmittance T of a metal foil was less than 2x10-17. The hypothesis is not supported since it predicts T=2x10-12

Effect of 3basic life support training programs in future primary school teachers. A quasi-experimental design.

Science.gov (United States)

Navarro-Patón, R; Freire-Tellado, M; Basanta-Camiño, S; Barcala-Furelos, R; Arufe-Giraldez, V; Rodriguez-Fernández, J E

2018-05-01

To evaluate the learning of basic life support (BLS) measures on the part of laypersons after 3different teaching programs. A quasi-experimental before-after study involving a non-probabilistic sample without a control group was carried out. Primary school teacher students from the University of Santiago (Spain). A total of 124 students (68.8% women and 31.2% men) aged 20-39 years (M=22.23; SD=3.79), with no previous knowledge of BLS, were studied. Three teaching programs were used: a traditional course, an audio-visual approach and feedback devices. Chest compressions as sole cardiopulmonary resuscitation skill evaluation: average compression depth, compression rate, chest recoil percentage and percentage of correct compressions. Automated external defibrillator: time needed to apply a shock before and after the course. There were significant differences in the results obtained after 2minutes of chest compressions, depending on the training program received, with feedback devices having a clear advantage referred to average compression depth (p<0.001), compression rate (p<0.001), chest recoil percentage (p<0.001) and percentage of correct compressions (p<0.001). Regarding automated external defibrillator, statistically significant differences were found in T after (p=0.025). The teaching course using feedback devices obtained the best results in terms of the quality of chest compressions, followed by the traditional course and audio-visual approach. These favorable results were present in both men and women. All 3teaching methods reached the goal of reducing defibrillation time. Copyright © 2017 Elsevier España, S.L.U. y SEMICYUC. All rights reserved.

Experimental study of radium partitioning between anorthite and melt at 1 atm

Energy Technology Data Exchange (ETDEWEB)

Miller, S; Burnett, D; Asimow, P; Phinney, D; Hutcheon, I

2007-03-08

We present the first experimental radium mineral/melt partitioning data, specifically between anorthite and a CMAS melt at atmospheric pressure. Ion microprobe measurement of coexisting anorthite and glass phases produces a molar D{sub Ra} = 0.040 {+-} 0.006 and D{sub Ra}/D{sub Ba} = 0.23 {+-} 0.05 at 1400 C. Our results indicate that lattice strain partitioning models fit the divalent (Ca, Sr, Ba, Ra) partition coefficient data of this study well, supporting previous work on crustal melting and magma chamber dynamics that has relied on such models to approximate radium partitioning behavior in the absence of experimentally determined values.

Experimental study of mechanical properties on spacer in NHR

International Nuclear Information System (INIS)

Jiang Yueyuan; Shi Jibing; Xu Yong

2007-01-01

The spacer of NHR-200 is composed mainly of the inner, outer and cornual strips which are ranged in egg-crate of 12 x 12-3. First, the pre-distortion of three kinds of three-arc springs on reactor working condition and their related clipping-force ranges are analyzed in this paper. Secondly, the mechanical experiments of 1:1 prototype, such as the load-distortion experiments, which the load and distortion are respectively measured by strain gauge and displacement sensor, of three kinds of springs, rigid supports and the spacers in two different directions are carried out on a special experimental facility. The experimental results show that the spacer can completely meet the design demands of mechanical properties of the fuel assemblies in NHR-200. (authors)

Analysis of experimental biosensor/FIA lactose measurements

Directory of Open Access Journals (Sweden)

Ferreira L.S.

2003-01-01

Full Text Available Whey is an abundant effluent in the production of cheese and casein. The biotechnological utilization of this economically important and nutritive source is limited mainly because of the presence of high percentages of lactose. This disaccharide has poor solubility, which can cause crystallization and insufficient sweetness in dairy food; additionally, part of the adult population suffers from associated lactose intolerance diseases. There are several methods to determine lactose such as spectrophotometry, polarimetry, infrared spectroscopy, titrimetry and chromatography. However these methods are tedious and time-consuming due to long sample preparation. These disadvantages stimulated the development of an enzymatic lactose biosensor. It employs two immobilized enzymes, beta-galactosidase and glucose oxidase and the quantitative analysis of lactose is based on determination of oxygen consumption in the enzymatic reaction. The influence of temperature on the biosensor signal was experimentally studied. It was observed that a nonlinear relationship exists between the electric response of the biosensor - provided by CAFCA (Computer Assisted Flow Control & Analysis - ANASYSCON, Hannover - and lactose concentration. In this work, attempts were made to correlate these variables using a simple nonlinear model and multilayered neural networks, with the latter providing the best modeling of the experimental data.

A safety-critical decision support system evaluation using situation awareness and workload measures

International Nuclear Information System (INIS)

Naderpour, Mohsen; Lu, Jie; Zhang, Guangquan

2016-01-01

To ensure the safety of operations in safety-critical systems, it is necessary to maintain operators' situation awareness (SA) at a high level. A situation awareness support system (SASS) has therefore been developed to handle uncertain situations [1]. This paper aims to systematically evaluate the enhancement of SA in SASS by applying a multi-perspective approach. The approach consists of two SA metrics, SAGAT and SART, and one workload metric, NASA-TLX. The first two metrics are used for the direct objective and subjective measurement of SA, while the third is used to estimate operator workload. The approach is applied in a safety-critical environment called residue treater, located at a chemical plant in which a poor human-system interface reduced the operator's SA and caused one of the worst accidents in US history. A counterbalanced within-subjects experiment is performed using a virtual environment interface with and without the support of SASS. The results indicate that SASS improves operators' SA, and specifically has benefits for SA levels 2 and 3. In addition, it is concluded that SASS reduces operator workload, although further investigations in different environments with a larger number of participants have been suggested. - Highlights: • The suitability of a cognitive decision support system is investigated. • An evaluation approach considering situation awareness and workload measures is proposed. • A computerized system based on the proposed approach is implemented. • The implemented system is used in a safety-critical environment.

Theoretical and experimental study of a calorimetric technique for measuring energy deposition in materials caused by complex pile irradiation

International Nuclear Information System (INIS)

Mas, P.; Sciers, P.; Droulers, Y.

1962-01-01

Calorimetric methods may be used to measure gamma fluxes greater than 10 6 r/h near the cores of swimming pool reactors. The theory, design, and properties of isothermal calorimeters are discussed, and experimental results obtained with two types are presented. Measurement of energy deposition in materials and the long term integration of energy depositions are other uses of these devices. Results of measurements on heat deposition in steel and water are given. Fluxes were also measured. (authors) [fr

The development of an enhanced strain measurement device to support testing of radioactive material packages

International Nuclear Information System (INIS)

Uncapkher, W.L.; Arviso, M.

1995-01-01

Radioactive material package designers use structural testing to verify and demonstrate package performance. A major part of evaluating structural response is the collection of reliable instrumentation measurement data. Over the last four decades, Sandia National Laboratories (SNL) has been actively involved in the development, testing, and evaluation of measurement devices for a broad range of applications, resulting in the commercialization of several measurement devices commonly used today. SNL maintains an ongoing program sponsored by the US Department of Energy (DOE) to develop and evaluate measurement devices to support testing of packages used to transport radioactive or hazardous materials. The development of the enhanced strain measurement device is part of this program

MEASUREMENT PROCESS OF SOFTWARE DEVELOPMENT PROJECTS FOR SUPPORTING STRATEGIC BUSINESS OBJECTIVES IN SOFTWARE DEVELOPING COMPANIES

Directory of Open Access Journals (Sweden)

Sandra Lais Pedroso

2013-08-01

Full Text Available Software developing companies work in a competitive market and are often challenged to make business decisions with impact on competitiveness. Models accessing maturity for software development processes quality, such as CMMI and MPS-BR, comprise process measurements systems (PMS. However, these models are not necessarily suitable to support business decisions, neither to achieve strategic goals. The objective of this work is to analyze how the PMS of software development projects could support business strategies for software developing companies. Results taken from this work show that PMS results from maturity models for software processes can be suited to help evaluating operating capabilities and supporting strategic business decisions.

Characterisation of large area THGEMs and experimental measurement of the Townsend coefficients for CF4

Science.gov (United States)

Burns, J.; Crane, T.; Ezeribe, A. C.; Grove, C. L.; Lynch, W.; Scarff, A.; Spooner, N. J. C.; Steer, C.

2017-10-01

Whilst the performance of small THGEMs is well known, here we consider the challenges in scaling these up to large area charge readouts. We first verify the expected gain of larger THGEMs by reporting experimental Townsend coefficients for a 10 cm diameter THGEM in low-pressure CF4. Large area 50 cm by 50 cm THGEMs were sourced from a commercial PCB supplier and geometrical imperfections were observed which we quantified using an optical camera setup. The large area THGEMs were experimentally characterised at Boulby Underground Laboratory through a series of gain calibrations and alpha spectrum measurements. ANSYS, Magboltz and Garfield++ simulations of the design of a TPC based on the large area THGEMs are presented. We also consider their implications for directional dark matter research and potential applications within nuclear security.

An Effective Experimental Optimization Method for Wireless Power Transfer System Design Using Frequency Domain Measurement

Directory of Open Access Journals (Sweden)

Sangyeong Jeong

2017-10-01

Full Text Available This paper proposes an experimental optimization method for a wireless power transfer (WPT system. The power transfer characteristics of a WPT system with arbitrary loads and various types of coupling and compensation networks can be extracted by frequency domain measurements. The various performance parameters of the WPT system, such as input real/imaginary/apparent power, power factor, efficiency, output power and voltage gain, can be accurately extracted in a frequency domain by a single passive measurement. Subsequently, the design parameters can be efficiently tuned by separating the overall design steps into two parts. The extracted performance parameters of the WPT system were validated with time-domain experiments.

Experimental technique of neutron reflection

International Nuclear Information System (INIS)

Chen Bo; Huang Chaoqiang; Li Xinxi

2006-12-01

It is presented that the classifications, structures and components of neutron reflectometer (NR), as well s functions and parameters of each components, detailed characters of NR facility 'PRN-2M'. Based on the practical experiments, the basic experimental techniques, the measurement and the related experimental settings are described, including the choice of experimental conditions, adjustments of polarized neutron beam line, basic experimental technique and approach of measurement. The above can be an instruction for NR experiments and a reference for NR construction. (authors)

Ab initio calculations and experimental measurement of the deuterium quadrupole coupling constant in Na2PDO3

International Nuclear Information System (INIS)

Trudeau, J.D.; Schwartz, J.L.; Farrar, T.C.

1991-01-01

The deuterium quadrupole coupling constant, χ D , in the PDO 3 2- anion has been measured in solution by NMR spin-lattice (T 1 ) relaxation time measurements and it has been calculated via ab initio methods. The experimental value of 94.7 ± 0.5 kHz is in excellent agreement with the ab initio value of 95.0 kHz. The activation energy for the ion reorientation is 2.23 ± 0.01 kJ mol -1

Development of a three-dimensional PIV measurement technique for the experimental study of air bubble collapse phenomena

International Nuclear Information System (INIS)

Yang, Y.H.; Hassan, Y.A.; Schmidl, W.D.

1995-01-01

Particle image velocimetry (PIV) is a quantitative flow measurement technique. The objective of this study is to develop a new three-dimensional PIV technique for the experimental study of air bubble collapse phenomena. A three-dimensional measurement technique is necessary since bubble collapse is a three-dimensional phenomenon. The investigation of the velocity flow field around a collapsing air bubble can provide detailed three-dimensional quantitative information to help improve the understanding of the related heat transfer processes

Experimental control of a fluidic pinball using genetic programming

Science.gov (United States)

Raibaudo, Cedric; Zhong, Peng; Noack, Bernd R.; Martinuzzi, Robert J.

2017-11-01

The wake stabilization of a triangular cluster of three rotating cylinders was investigated in the present study. Experiments were performed at Reynolds number Re 6000, and compared with URANS-2D simulations at same flow conditions. 2D2C PIV measurements and constant temperature anemometry were used to characterize the flow without and with actuation. Open-loop actuation was first considered for the identification of particular control strategies. Machine learning control was also implemented for the experimental study. Linear genetic programming has been used for the optimization of open-loop parameters and closed-loop controllers. Considering a cost function J based on the fluctuations of the velocity measured by the hot-wire sensor, significant performances were achieved using the machine learning approach. The present work is supported by the senior author's (R. J. Martinuzzi) NSERC discovery Grant. C. Raibaudo acknowledges the financial support of the University of Calgary Eyes-High PDF program.

Awareness and behavior of oncologists and support measures in medical institutions related to ongoing employment of cancer patients in Japan.

Science.gov (United States)

Wada, Koji; Ohtsu, Mayumi; Aizawa, Yoshiharu; Tanaka, Hiroshi; Tagaya, Nobumi; Takahashi, Miyako

2012-04-01

Improved outcomes of cancer treatment allow patients to undergo treatment while working. However, support from oncologists and medical institutions is essential for patients to continue working. This study aimed to clarify oncologists' awareness and behavior regarding patients who work during treatment, support in medical institutions and their association. A questionnaire was mailed to all 453 diplomates and faculty of the subspecialty board of medical oncology in the Japanese Society of Medical Oncology and all 1016 surgeons certified by the Japanese Board of Cancer Therapy living in the Kanto area. The questionnaire assessed demographics, oncologist awareness and behavior regarding patient employment and support measures at their medical institutions. Logistic regression analysis was used to examine the association of awareness and behavior of oncologists with support measures at their institutions. A total of 668 individuals participated. The overall response rate was 45.5%. Only 53.6% of respondents advised patients to tell their supervisors about prospects for treatment and ask for understanding. For medical institutions, 28.8% had a nurse-involved counseling program and adjustments in radiation therapy (28.0%) and chemotherapy (41.9%) schedules to accommodate patients' work. There was a significant correlation between awareness and behavior of oncologists and medical institutions' measures to support employed cancer patients. There is room for improvement in awareness and behavior of oncologists and support in medical institutions for cancer patients continuing to work. Oncologists could support working patients by exerting influence on their medical institutions. Conversely, proactive development of support measures by medical institutions could alter the awareness and behavior of oncologists.

Awareness and behavior of oncologists and support measures in medical institutions related to ongoing employment of cancer patients in Japan

International Nuclear Information System (INIS)

Wada, Koji; Aizawa, Yoshiharu; Ohtsu, Mayumi; Tanaka, Hiroshi; Tagaya, Nobumi; Takahashi, Miyako

2012-01-01

Improved outcomes of cancer treatment allow patients to undergo treatment while working. However, support from oncologists and medical institutions is essential for patients to continue working. This study aimed to clarify oncologists' awareness and behavior regarding patients who work during treatment, support in medical institutions and their association. A questionnaire was mailed to all 453 diplomates and faculty of the subspecialty board of medical oncology in the Japanese Society of Medical Oncology and all 1016 surgeons certified by the Japanese Board of Cancer Therapy living in the Kanto area. The questionnaire assessed demographics, oncologist awareness and behavior regarding patient employment and support measures at their medical institutions. Logistic regression analysis was used to examine the association of awareness and behavior of oncologists with support measures at their institutions. A total of 668 individuals participated. The overall response rate was 45.5%. Only 53.6% of respondents advised patients to tell their supervisors about prospects for treatment and ask for understanding. For medical institutions, 28.8% had a nurse-involved counseling program and adjustments in radiation therapy (28.0%) and chemotherapy (41.9%) schedules to accommodate patients' work. There was a significant correlation between awareness and behavior of oncologists and medical institutions' measures to support employed cancer patients. There is room for improvement in awareness and behavior of oncologists and support in medical institutions for cancer patients continuing to work. Oncologists could support working patients by exerting influence on their medical institutions. Conversely, proactive development of support measures by medical institutions could alter the awareness and behavior of oncologists. (author)

Experimental Set-up and Full-scale measurements in the ‘Cube'

DEFF Research Database (Denmark)

Kalyanova, Olena; Heiselberg, Per

The Cube' is an outdoor test facility located at the main campus of Aalborg University. It has been built in the fall of 2005 with the purpose of detailed investigations of the DSF performance, development of the empirical test cases for validation and further improvements of various building...... of any power supplied to the experimental zone in order to maintain the necessary thermal conditions. An accuracy of these measurements is justified by the quality of the facility construction: ‘the Cube' is very well insulated and tight....... simulation software for the modelling of buildings with double skin facades in the frame of IEA ECBCS ANNEX 43/SHC Task 34, Subtask EDouble Skin Facade. The test facility is designed to be flexible for a choice of the DSF operational modes, natural or mechanical flow conditions, different types of shading...

Calculation of kinetic parameters of Caliban metallic core experimental reactor from stochastic neutron measurements

Energy Technology Data Exchange (ETDEWEB)

Casoli, P.; Authier, N.; Baud, J. [Commissariat a l' energie Atomique, Centre de Valduc, 21120 Is-sur-Tille (France)

2009-07-01

Several experimental devices are operated by the Criticality and Neutron Science Research Department of the CEA Valduc Laboratory. One of these is the metallic core reactor Caliban. The knowledge of the fundamental kinetic parameters of the reactor is very useful, indeed necessary, to the operator. The purpose of this study was to develop and perform experiments allowing to determinate some of these parameters. The prompt neutron decay constant and particularly its value at criticality can be measured with reactor noise techniques such as the interval-distribution, the Feynman variance-to-mean, and the Rossi-{alpha} methods. By introducing the Nelson number, the effective delayed neutron fraction and the average neutron lifetime can also be calculated with the Rossi-{alpha} method. Subcritical, critical, and even supercritical experiments were performed. With the Rossi-{alpha} technique, it was found that the prompt neutron decay constant at criticality was (6.02*10{sup 5} {+-} 9%). Experiments also brought out the limitations of the used experimental parameters. (authors)

Numerical models: Detailing and simulation techniques aimed at comparison with experimental data, support to test result interpretation

International Nuclear Information System (INIS)

Lin Chiwen

2001-01-01

This part of the presentation discusses the modelling details required and the simulation techniques available for analyses, facilitating the comparison with the experimental data and providing support for interpretation of the test results. It is organised to cover the following topics: analysis inputs; basic modelling requirements for reactor coolant system; method applicable for reactor cooling system; consideration of damping values and integration time steps; typical analytic models used for analysis of reactor pressure vessel and internals; hydrodynamic mass and fluid damping for the internal analysis; impact elements for fuel analysis; and PEI theorem and its applications. The intention of these topics is to identify the key parameters associated with models of analysis and analytical methods. This should provide proper basis for useful comparison with the test results

Experimental Platform for measuring the parameters of magnetization of a transformer in a quasi-static transitional regime

International Nuclear Information System (INIS)

Milovanski, Vasil; , Blagoevgrad (Bulgaria))" data-affiliation=" (HMS “Acad. S. P. Corolov, Blagoevgrad (Bulgaria))" >Stoyanov, Krasimir; Milovanska, Stefani

2013-01-01

Some opportunities for development of an experimental module for magnetic research have been examined in the current paper. The goal is to attain a more accurate reading of the measured electrical signals which are directly related to the magnetic parameters and characteristics of the ferromagnetic material

Monitoringsprogramma experimentele gecombineerde luchtwassers op veehouderijbedrijven = Measurement program on experimental multi-pollutant air scrubbers at animal houses

NARCIS (Netherlands)

Melse, R.W.; Hol, J.M.G.; Mosquera Losada, J.; Nijeboer, G.M.; Huis in 'T Veld, J.W.H.; Hattum, van T.G.; Kwikkel, R.K.; Dousma, F.; Ogink, N.W.M.

2011-01-01

A measurement program was carried out in which the performance of 5 experimental scrubbers on animal farms was monitored for the removal of ammonia, odour and fine dust (PM10, PM2.5). This reports discusses and evaluates the realization of the program and its results.

Development of a nuclear emergency preparedness support system. MEASURES and its advanced edition

International Nuclear Information System (INIS)

Hara, Tomohiro; Nakatsuka, Shigehiro; Watanabe, Osami; Adachi, Takeshi

2007-01-01

We have developed a new nuclear emergency preparedness support system for a micro scale area, called the advanced edition of MEASURES. The system simulates atmospheric dispersion of radioactive material quickly and accurately, using an airflow database and a dispersion model. It takes less than 15 minutes for 12-hour simulation, on a personal computer. The user can operate the system by GUI. (author)

The association between implicit and explicit attitudes toward smoking and support for tobacco control measures.

Science.gov (United States)

Macy, Jonathan T; Chassin, Laurie; Presson, Clark C

2013-01-01

This study examined the association between implicit and explicit attitudes toward smoking and support for tobacco control policies. Participants were from an ongoing longitudinal study of the natural history of smoking who also completed a web-based assessment of implicit attitudes toward smoking (N = 1,337). Multiple regression was used to test the association between covariates (sex, age, educational attainment, parent status, and smoking status), implicit attitude toward smoking, and explicit attitude toward smoking and support for tobacco control policies. The moderating effect of the covariates on the relation between attitudes and support for policies was also tested. Females, those with higher educational attainment, parents, and nonsmokers expressed more support for tobacco control policy measures. For nonsmokers, only explicit attitude was significantly associated with support for policies. For smokers, both explicit and implicit attitudes were significantly associated with support. The effect of explicit attitude was stronger for those with lower educational attainment. Both explicit and implicit smoking attitudes are important for building support for tobacco control policies, particularly among smokers. More research is needed on how to influence explicit and implicit attitudes to inform policy advocacy campaigns.

Experimental techniques of conversion coefficient measurements

International Nuclear Information System (INIS)

Hamilton, J.H.

1975-01-01

Discusses briefly the history of conversion electron spectra measurements, and the interpretation of the collected data. Then provides a comprehensive review of techniques presently available to measure the conversion coefficients. (Auth.)

Quantum mechanics and the theories of local hidden variables: an experimental test by measuring the spin correlation function in p-p scattering

International Nuclear Information System (INIS)

Lamehi-Rachti, Mohammad.

1976-01-01

The Einstein-Podolsky-Rosen paradox is briefly exposed with the Bell theorem on hidden variables and the locality principle. The conditions for an ideal experiment are discussed and the results from γ-γ correlation experiments are given. The principle of an experimental measurement of the spin correlation function predicted by the quantum mechanics theory is derived, new hypotheses to be introduced are discussed. The formula giving the dependence of the counting asymmetry on the spin correlation function, polarimeter analyzing power, and geometric correlation is developed. The principle of a Monte Carlo calculation is also exposed. The experimental device is described with the methods for measuring the subsidiary quantities and experimental results are analyzed [fr

Sustained Implementation Support Scale: Validation of a Measure of Program Characteristics and Workplace Functioning for Sustained Program Implementation.

Science.gov (United States)

Hodge, Lauren M; Turner, Karen M T; Sanders, Matthew R; Filus, Ania

2017-07-01

An evaluation measure of enablers and inhibitors to sustained evidence-based program (EBP) implementation may provide a useful tool to enhance organizations' capacity. This paper outlines preliminary validation of such a measure. An expert informant and consumer feedback approach was used to tailor constructs from two existing measures assessing key domains associated with sustained implementation. Validity and reliability were evaluated for an inventory composed of five subscales: Program benefits, Program burden, Workplace support, Workplace cohesion, and Leadership style. Exploratory and confirmatory factor analysis with a sample of 593 Triple P-Positive Parenting Program-practitioners led to a 28-item scale with good reliability and good convergent, discriminant, and predictive validity. Practitioners sustaining implementation at least 3 years post-training were more likely to have supervision/peer support, reported higher levels of program benefit, workplace support, and positive leadership style, and lower program burden compared to practitioners who were non-sustainers.

Agricultural support measures of advanced countries and food insecurity in developing countries

OpenAIRE

Herrmann, Michael

2006-01-01

Many developing nations, especially the least developed countries, are subjected to recurrent spells of food insecurity. In order to understand food insecurity in these countries it is necessary to consider not only immediate or trigger-causes of food crises, but also its underlying or systemic causes. This paper argues that the agricultural support measures of advanced countries may act as a systemic cause for food insecurity in developing countries. While the import of subsidized foods by d...

Ultrasonic imaging of tube/support structure of power plant steam generators

International Nuclear Information System (INIS)

Saniie, J.; Nagle, D.T.

1987-01-01

The corrosion and erosion of steam generator tubing in nuclear power plants can present problems of both safety and economics. In steam generators, the inconel tubes are fit loosely through holes drilled in carbon steel support plates. Corrosion is of particular concern with such tube/support plate structures. Non-protective magnetite can build up on the inner surface of the support plate holes, and allowed to continue unchecked, will fill the gap, eventually denting and fracturing the tube walls. Therefore, periodic nondestructive inspection can be valuable in characterizing corrosion and can be used in evaluating the effectiveness of chemical treatments used to control or reduce corrosion. Presently, they are investigating the feasibility and practicality of using ultrasound in routing testing for gap measurement, for evaluating the corrosion and assessing the degree of denting. The tube/support structure can be modeled as a multilayer, reverberant target, which when tested with ultrasound results in two sets of reverberating echoes [1]. One set corresponds to the tube wall and the other to the support plate. These echoes must be decomposed and identified in order to evaluate the tube/support structure. This report presents experimental results along with a discussion of various measurements and processing techniques for decomposing and interpreting tube/support echoes at different stages of corrosion

Experimental test of static and dynamic characteristics of tilting-pad thrust bearings

Directory of Open Access Journals (Sweden)

Annan Guo

2015-07-01

Full Text Available The axial vibration in turbine machine has attracted more and more interest. Tilting-pad thrust bearings are widely used in turbine machines to support the axial load. The dynamic properties generated by oil film of the thrust pad have important effects on the axial vibration of the rotor-bearing system. It is necessary to develop the method to test the dynamic characteristics of thrust bearings. A new rig has been developed. The facility allows a complete set of bearing operating parameters to be measured. Parameters measured include oil temperatures, oil-film thickness, and pressure. The static load and dynamic load can be added on the thrust bearing in the vertical direction at the same time. The relative and absolute displacement vibrations of the test experimental bearing with the changes of dynamic force are measured, and the dynamic characteristics of the test bearing are obtained. The experimental results show clearly that the operating conditions influence largely on the pad static and dynamic characteristics.

Measuring Supportive Music and Imagery Interventions: The Development of the Music Therapy Self-Rating Scale.

Science.gov (United States)

Meadows, Anthony; Burns, Debra S; Perkins, Susan M

2015-01-01

Previous research has demonstrated modest benefits from music-based interventions, specifically music and imagery interventions, during cancer care. However, little attention has been paid to measuring the benefits of music-based interventions using measurement instruments specifically designed to account for the multidimensional nature of music-imagery experiences. The purpose of this study was to describe the development of, and psychometrically evaluate, the Music Therapy Self-Rating Scale (MTSRS) as a measure for cancer patients engaged in supportive music and imagery interventions. An exploratory factor analysis using baseline data from 76 patients who consented to participate in a music-based intervention study during chemotherapy. Factor analysis of 14 items revealed four domains: Awareness of Body, Emotionally Focused, Personal Resources, and Treatment Specific. Internal reliability was excellent (Cronbach alphas ranging from 0.75 to 0.88) and construct and divergent-discriminant validity supported. The MTSRS is a psychometrically sound, brief instrument that captures essential elements of patient experience during music and imagery interventions. © the American Music Therapy Association 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Z0 decay modes - experimental measurements

International Nuclear Information System (INIS)

Dorfan, J.M.

1984-08-01

This report summarizes three lectures given at the Theoretical Advanced Study Institute at the University of Michigan at Ann Arbor. The lectures begin with an introduction to storage rings and linear colliders with special reference to the parameters of the SLC and LEP. The rigors of the Z 0 environment are presented along with the requirements for SLC and LEP detectors. The pedagogy needed for testing the Standard Model is developed, and some experimental tests of the Standard Model are discussed. Tests which involve extensions of the Standard Model (charged Higgs particles, more generations) as well as a few examples of how supersymmetry may show up at the Z 0 are discussed. 25 references, 34 figures

Pedagogical support of competence formation: methodological bases and experimental context

OpenAIRE

NABIEV VALERY SHARIFYANOVICH

2016-01-01

The article considers the problem of competence approach methodological basis. It discusses the topical issues of organizing a holistic educational process. The article presents the original solutions created by the author and the results of experimental verification of the specified conditions of pedagogical maintenance of educational and training activities.

Measurement of thermal conductance

International Nuclear Information System (INIS)

Kuchnir, M.

1977-01-01

The 6-m long, 45-kG, warm-iron superconducting magnets envisioned for the Energy Doubler stage of the Fermilab accelerator require stiff supports with minimized thermal conductances in order to keep the refrigeration power reasonable. The large number of supports involved in the system required a careful study of their heat conduction from the room temperature wall to the intercepting refrigeration at 20 0 K and to the liquid helium. For this purpose the thermal conductance of this support was measured by comparing it with the thermal conductance of a copper strap of known geometry. An association of steady-state thermal analysis and experimental thermal conductivity techniques forms the basis of this method. An important advantage is the automatic simulation of the 20 0 K refrigeration intercept by the copper strap, which simplifies the apparatus considerably. This relative resistance technique, which uses electrical analogy as a guideline, is applicable with no restrictions for materials with temperature-independent thermal conductivity. For other materials the results obtained are functions of the specific temperature interval involved in the measurements. A comprehensive review of the literature on thermal conductivity indicates that this approach has not been used before. A demonstration of its self-consistency is stressed here rather than results obtained for different supports

Nuclear test experimental science

International Nuclear Information System (INIS)

Struble, G.L.; Middleton, C.; Bucciarelli, G.; Carter, J.; Cherniak, J.; Donohue, M.L.; Kirvel, R.D.; MacGregor, P.; Reid, S.

1989-01-01

This report discusses research being conducted at Lawrence Livermore Laboratory under the following topics: prompt diagnostics; experimental modeling, design, and analysis; detector development; streak-camera data systems; weapons supporting research

Nuclear test experimental science

Energy Technology Data Exchange (ETDEWEB)

Struble, G.L.; Middleton, C.; Bucciarelli, G.; Carter, J.; Cherniak, J.; Donohue, M.L.; Kirvel, R.D.; MacGregor, P.; Reid, S. (eds.)

1989-01-01

This report discusses research being conducted at Lawrence Livermore Laboratory under the following topics: prompt diagnostics; experimental modeling, design, and analysis; detector development; streak-camera data systems; weapons supporting research.

Experimental verification of a bridge-shaped, nonlinear vibration energy harvester

Energy Technology Data Exchange (ETDEWEB)

Gafforelli, Giacomo, E-mail: giacomo.gafforelli@polimi.it; Corigliano, Alberto [Department of Civil and Environmental Engineering, Politecnico di Milano, Milano, 20133 (Italy); Xu, Ruize; Kim, Sang-Gook [Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

2014-11-17

This paper reports a comprehensive modeling and experimental characterization of a bridge shaped nonlinear energy harvester. A doubly clamped beam at large deflection requires stretching strain in addition to the bending strain to be geometrically compatible, which stiffens the beam as the beam deflects and transforms the dynamics to a nonlinear regime. The Duffing mode non-linear resonance widens the frequency bandwidth significantly at higher frequencies than the linear resonant frequency. The modeling includes a nonlinear measure of strain coupled with piezoelectric constitutive equations which end up in nonlinear coupling terms in the equations of motion. The main result supports that the power generation is bounded by the mechanical damping for both linear and nonlinear harvesters. Modeling also shows the power generation is over a wider bandwidth in the nonlinear case. A prototype is manufactured and tested to measure the power generation at different load resistances and acceleration amplitudes. The prototype shows a nonlinear behavior with well-matched experimental data to the modeling.

Results of environmental radiation monitoring and meteorology measurements (material prepared for obtaining the licence for RA reactor experimental operation)

International Nuclear Information System (INIS)

1980-10-01

According to the demands for obtaining the licence for restarting the Ra reactor and the experimental operation this document includes the radiation monitoring measured data in the working space and environment of the RA reactor, i.e. Boris Kidric Institute. The meteorology measured data are included as well. All the measurements are performed according to the radiation protection program applied actually from the first reactor start-up at the end of 1959 [sr

A pulsed eddy current probe for inspection of support plates from within Alloy-800 steam generator tubes

International Nuclear Information System (INIS)

Krause, T. W.; Babbar, V. K.; Underhill, P. R.

2014-01-01

Support plate degradation and fouling in nuclear steam generators (SGs) can lead to SG tube corrosion and loss of efficiency. Inspection and monitoring of these conditions can be integrated with preventive maintenance programs, thereby advancing station-life management processes. A prototype pulsed eddy current (PEC) probe, targeting inspection issues associated with SG tubes in SS410 tube support plate structures, has been developed using commercial finite element (FE) software. FE modeling was used to identify appropriate driver and pickup coil configurations for optimum sensitivity to changes in gap and offset for Alloy-800 SG tubes passing through 25 mm thick SS410 support plates. Experimental measurements using a probe that was manufactured based on the modeled configuration, were used to confirm the sensitivity of differential PEC signals to changes in relative position of the tube within the tube support plate holes. Models investigated the effect of shift and tilt of tube with respect to hole centers. Near hole centers and for small shifts, modeled signal amplitudes from the differentially connected coil pairs were observed to change linearly with tube shift. This was in agreement with experimentally measured TEC coil response. The work paves the way for development of a system targeting the inspection and evaluation of support plate structures in steam generators

A pulsed eddy current probe for inspection of support plates from within Alloy-800 steam generator tubes

Science.gov (United States)

Krause, T. W.; Babbar, V. K.; Underhill, P. R.

2014-02-01

Support plate degradation and fouling in nuclear steam generators (SGs) can lead to SG tube corrosion and loss of efficiency. Inspection and monitoring of these conditions can be integrated with preventive maintenance programs, thereby advancing station-life management processes. A prototype pulsed eddy current (PEC) probe, targeting inspection issues associated with SG tubes in SS410 tube support plate structures, has been developed using commercial finite element (FE) software. FE modeling was used to identify appropriate driver and pickup coil configurations for optimum sensitivity to changes in gap and offset for Alloy-800 SG tubes passing through 25 mm thick SS410 support plates. Experimental measurements using a probe that was manufactured based on the modeled configuration, were used to confirm the sensitivity of differential PEC signals to changes in relative position of the tube within the tube support plate holes. Models investigated the effect of shift and tilt of tube with respect to hole centers. Near hole centers and for small shifts, modeled signal amplitudes from the differentially connected coil pairs were observed to change linearly with tube shift. This was in agreement with experimentally measured TEC coil response. The work paves the way for development of a system targeting the inspection and evaluation of support plate structures in steam generators.

Noninvasive measurement of nutrient portal blood shunting: an experimental study with [14C]ursodeoxycholic acid

International Nuclear Information System (INIS)

Nordlinger, B.; Parquet, M.; Infante, R.; Moreels, R.; Blondiau, P.; Boschat, M.; Groussard, M.; Huguet, C.

1982-01-01

All of the methods proposed for measuring portal blood flow are either invasive, estimate total rather than nutrient flow, and none has proved reliable in cirrhotic patients. A method has been derived from pharmacokinetic principles used for the calculation of bioavailability of drugs according to the route of administration (i.v. or p.o.) and tested experimentally in 20 pigs. A tracer dose of [ 14 C]ursodeoxycholic acid, a biliary acid with a high-liver first-pass effect, is administered in the duodenum, and serial peripheral blood samples are taken. Later, the same dose of the same drug is administered i.v. The shunt fraction of portal blood F is obtained by the ratio of the areas under the plasma level vs. time curves (AUC) after p.o. and i.v. administrations: (see formula in text). The pigs were divided into three experimental groups. (i) Group I: undisturbed portal flow; (ii) Group II: total diversion of portal blood with an end-to-side portacaval shunt, and (iii) Group III: partial diversion of portal blood through a side-to-side portacaval shunt. Portal flow was measured during surgery with an electromagnetic flowmeter above and below the shunt and the degree of shunting calculated. Results show that the shunt fraction measured with ursodeoxycholic acid is well-correlated with hemodynamic data. No overlap between Groups I and III is observed. It is concluded that the shunt fraction of nutrient portal blood can be measured with this noninvasive method. Minute amounts of ursodeoxycholic acid were used in order to be completely metabolized by the liver, even in spite of hepatocellular dysfunction. Therefore, this method should be valid in cirrhotic patients and be useful to decide the type of portasystemic shunt to propose for the decompression of gastroesophageal varices

.A computer program for nuclear lifetimes measurements by DSAM using a self-supporting target

International Nuclear Information System (INIS)

Morand, C.; Chan, T.U.

1981-02-01

The present Doppler Shift Attenuation Method, for nuclear lifetimes measurements using self supporting target, has already been described. Therefore this paper only mentions the peculiar features of that DSAM, describes several code facilities, comments the subroutines working along the program structure, in order to be easily handled by other physicists

Parent-reported social support for child’s fruit and vegetable intake: validity of measures

Science.gov (United States)

The objective of our study was to develop and validate measures of parental social support to increase their child’s fruit and vegetable (FV) consumption. We used a cross-sectional study design by studying participants at school and home. We studied two hundred three parents with at least 1 elemen...

Experimental study of fission process by fragment-neutron correlation measurement

Energy Technology Data Exchange (ETDEWEB)

Nishio, Katsuhisa; Yamamoto, Hideki; Kanno, Ikuo; Kimura, Itsuro; Nakagome, Yoshihiro [Kyoto Univ. (Japan). Faculty of Engineering

1997-07-01

Fragment-neutron correlation measurement of {sup 235}U(n{sub th}, f) was carried out. The obtained results showed more statistical accuracy than that of reported thermal neutron reaction. Experimental results and it`s analysis made clear the following facts. The minimum values of <{eta}> (m*) are shown at about 90 and 145 {mu} and <{eta}> (m*) showed the symmetrical form with an axis of symmetrical fission. This tendency is same as the distribution of {sup 252}Cf(s.f). -dV/dTKE(m*) indicates the saw-teethed distribution as same as <{nu}>(m*). The distribution seems depend on stiffness of fission fragment affected by the shell effect. The level density parameter a(m*) of fission fragment obtained from {sup 235}U(n{sub th}, f) expresses the saw-teethed distribution as same as that of {sup 252}Cf(s.f). This distribution can be explained by the empirical equation under consideration of the fission fragment depending on the shell effect and the collective motion. (S.Y.)

Experimental measurement of enthalpy increments of Th0.25Ce0.75O2

International Nuclear Information System (INIS)

Babu, R.; Balakrishnan, S.; Ananthasivan, K.; Nagarajan, K.

2013-01-01

Thorium has been suggested as an alternative fertile material for a nuclear fuel cycle, and an inert matrix for burning plutonium and for waste disposal. The third stage of India's nuclear power programme envisages utilization of thorium and plutonium as a fuel in Advanced Heavy Water Reactor (AHWR) and Accelerator Driven Sub-critical Systems (ADSS). Solid solutions of ThO 2 -PuO 2 are of importance because of coexistence of Th with Pu during the breeding cycle. CeO 2 is used as a PuO 2 analog due to similar ionic radii of cations and similar physico-chemical properties of the oxides. ThO 2 forms a homogeneous solid solution with the cubic fluorite structure when doped with Ce in the entire compositional range. In the development of mixed oxide nuclear fuels, knowledge of thermodynamic properties of thorium oxide and its mixtures has become extremely importance for understanding the fuel behavior during irradiation and for predicting the performance of the fuel under accidental conditions. Thermodynamic functions such as the enthalpy increment and heat capacity of the theria-ceria solid solution have not been measured experimentally. Hence, the enthalpy increments of thoria-ceria solid solutions, Th 0.25 Ce 0.75 O 2 by inverse drop calorimetry in the temperature range 523-1723 K have been measured. The measured enthalpy increments were fitted in to polynomial functions by using the least squares method and the other thermodynamic functions such as heat capacity, entropy and Gibbs energy functions were computed in the temperature range 298-1800 K. The reported thermodynamic functions for Th 0.25 Ce 0.75 O 2 forms the first experimental data and the heat capacity of (Th,Ce)O 2 solid solutions was shown to obey the Neumann-Kopp's rule. (author)

Optimal Bayesian experimental design for priors of compact support with application to shock-tube experiments for combustion kinetics

KAUST Repository

Bisetti, Fabrizio

2016-01-12

The analysis of reactive systems in combustion science and technology relies on detailed models comprising many chemical reactions that describe the conversion of fuel and oxidizer into products and the formation of pollutants. Shock-tube experiments are a convenient setting for measuring the rate parameters of individual reactions. The temperature, pressure, and concentration of reactants are chosen to maximize the sensitivity of the measured quantities to the rate parameter of the target reaction. In this study, we optimize the experimental setup computationally by optimal experimental design (OED) in a Bayesian framework. We approximate the posterior probability density functions (pdf) using truncated Gaussian distributions in order to account for the bounded domain of the uniform prior pdf of the parameters. The underlying Gaussian distribution is obtained in the spirit of the Laplace method, more precisely, the mode is chosen as the maximum a posteriori (MAP) estimate, and the covariance is chosen as the negative inverse of the Hessian of the misfit function at the MAP estimate. The model related entities are obtained from a polynomial surrogate. The optimality, quantified by the information gain measures, can be estimated efficiently by a rejection sampling algorithm against the underlying Gaussian probability distribution, rather than against the true posterior. This approach offers a significant error reduction when the magnitude of the invariants of the posterior covariance are comparable to the size of the bounded domain of the prior. We demonstrate the accuracy and superior computational efficiency of our method for shock-tube experiments aiming to measure the model parameters of a key reaction which is part of the complex kinetic network describing the hydrocarbon oxidation. In the experiments, the initial temperature and fuel concentration are optimized with respect to the expected information gain in the estimation of the parameters of the target

EXPERIMENTAL MEASUREMENT, ANALYSIS AND MODELLING OF DEPENDENCY EMISSIVITY IN FUNCTION OF TEMPERATURE

Directory of Open Access Journals (Sweden)

N. Baba Ahmed

2015-08-01

Full Text Available We propose a direct method of measurement of the total emissivity of opaque samples on a range of temperature around the ambient one. The method rests on the modulation of the temperature of the sample and the infra-red signal processing resulting from the surface of the sample we model the total emissivity obtained in experiments according to the temperature to establish linear correlations. This leads us to apply the method of optimal linearization associated the finite element method with the nonlinear problem of transfer of heat if thermal conductivity, the specific heat and the emissivity of studied material depend on the temperature. We obtain a good agreement between the resolution of the nonlinear equation of heat and the results obtained by the experimentation. .

Design, Specification and Construction of Specialized Measurement System in the Experimental Building

Science.gov (United States)

Fedorczak-Cisak, Malgorzata; Kwasnowski, Pawel; Furtak, Marcin; Hayduk, Grzegorz

2017-10-01

Experimental buildings for “in situ” research are a very important tool for collecting data on energy efficiency of the energy-saving technologies. One of the most advanced building of this type in Poland is the Maloposkie Laboratory of Energy-saving Buildings at Cracow University of Technology. The building itself is used by scientists as a research object and research tool to test energy-saving technologies. It is equipped with a specialized measuring system consisting of approx. 3 000 different sensors distributed in technical installations and structural elements of the building (walls, ceilings, cornices) and the ground. The authors of the paper will present the innovative design and technology of this specialized instrumentation. They will discuss issues arising during the implementation and use of the building.

Experimental Neutrino Physics

Energy Technology Data Exchange (ETDEWEB)

Wilkes, Richard Jeffrey [Univ. of Washington, Seattle, WA (United States)

2017-11-15

The University of Washington (UW) HEP neutrino group performed experimental research on the physics of neutrinos, using the capabilities offered by the T2K Experiment and the Super-Kamiokande Neutrino Observatory. The UW group included senior investigator R. J. Wilkes, two PhD students, four MS degree students, and a research engineer, all of whom are members of the international scientific collaborations for T2K and Super-Kamiokande. During the period of support, within T2K we pursued new precision studies sensitive to new physics, going beyond the limits of current measurements of the fundamental neutrino oscillation parameters (mass differences and mixing angles). We began efforts to measure (or significantly determine the absence of) 1 the CP-violating phase parameter δCP and determine the neutrino mass hierarchy. Using the Super-Kamiokande (SK) detector we pursued newly increased precision in measurement of neutrino oscillation parameters with atmospheric neutrinos, and extended the current reach in searches for proton decay, in addition to running the most sensitive supernova watch instrument [Scholberg 2012], performing other astrophysical neutrino studies, and analyzing beam-induced events from T2K. Overall, the research addressed central questions in the field of particle physics. It included the training of graduate students (both PhD and professional MS degree students), and postdoctoral researchers. Undergraduate students also participated as laboratory assistants.

Seeing mental states: An experimental strategy for measuring the observability of other minds

Science.gov (United States)

Becchio, Cristina; Koul, Atesh; Ansuini, Caterina; Bertone, Cesare; Cavallo, Andrea

2018-03-01

Is it possible to perceive others' mental states? Are mental states visible in others' behavior? In contrast to the traditional view that mental states are hidden and not directly accessible to perception, in recent years a phenomenologically-motivated account of social cognition has emerged: direct social perception. However, despite numerous published articles that both defend and critique direct perception, researchers have made little progress in articulating the conditions under which direct perception of others' mental states is possible. This paper proposes an empirically anchored approach to the observability of others' mentality - not just in the weak sense of discussing relevant empirical evidence for and against the phenomenon of interest, but also, and more specifically, in the stronger sense of identifying an experimental strategy for measuring the observability of mental states and articulating the conditions under which mental states are observable. We conclude this article by reframing the problem of direct perception in terms of establishing a definable and measurable relationship between movement features and perceived mental states.

Isotopic Resonance Hypothesis: Experimental Verification by Escherichia coli Growth Measurements

Science.gov (United States)

Xie, Xueshu; Zubarev, Roman A.

2015-03-01

Isotopic composition of reactants affects the rates of chemical and biochemical reactions. As a rule, enrichment of heavy stable isotopes leads to progressively slower reactions. But the recent isotopic resonance hypothesis suggests that the dependence of the reaction rate upon the enrichment degree is not monotonous. Instead, at some ``resonance'' isotopic compositions, the kinetics increases, while at ``off-resonance'' compositions the same reactions progress slower. To test the predictions of this hypothesis for the elements C, H, N and O, we designed a precise (standard error +/-0.05%) experiment that measures the parameters of bacterial growth in minimal media with varying isotopic composition. A number of predicted resonance conditions were tested, with significant enhancements in kinetics discovered at these conditions. The combined statistics extremely strongly supports the validity of the isotopic resonance phenomenon (p biotechnology, medicine, chemistry and other areas.

MSDD: a manually curated database of experimentally supported associations among miRNAs, SNPs and human diseases.

Science.gov (United States)

Yue, Ming; Zhou, Dianshuang; Zhi, Hui; Wang, Peng; Zhang, Yan; Gao, Yue; Guo, Maoni; Li, Xin; Wang, Yanxia; Zhang, Yunpeng; Ning, Shangwei; Li, Xia

2018-01-04

The MiRNA SNP Disease Database (MSDD, http://www.bio-bigdata.com/msdd/) is a manually curated database that provides comprehensive experimentally supported associations among microRNAs (miRNAs), single nucleotide polymorphisms (SNPs) and human diseases. SNPs in miRNA-related functional regions such as mature miRNAs, promoter regions, pri-miRNAs, pre-miRNAs and target gene 3'-UTRs, collectively called 'miRSNPs', represent a novel category of functional molecules. miRSNPs can lead to miRNA and its target gene dysregulation, and resulting in susceptibility to or onset of human diseases. A curated collection and summary of miRSNP-associated diseases is essential for a thorough understanding of the mechanisms and functions of miRSNPs. Here, we describe MSDD, which currently documents 525 associations among 182 human miRNAs, 197 SNPs, 153 genes and 164 human diseases through a review of more than 2000 published papers. Each association incorporates information on the miRNAs, SNPs, miRNA target genes and disease names, SNP locations and alleles, the miRNA dysfunctional pattern, experimental techniques, a brief functional description, the original reference and additional annotation. MSDD provides a user-friendly interface to conveniently browse, retrieve, download and submit novel data. MSDD will significantly improve our understanding of miRNA dysfunction in disease, and thus, MSDD has the potential to serve as a timely and valuable resource. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

Design of an experimental apparatus for measurement of the surface tension of metastable fluids

Science.gov (United States)

Vinš, V.; Hrubý, J.; Hykl, J.; Blaha, J.; Šmíd, B.

2013-04-01

A unique experimental apparatus for measurement of the surface tension of aqueous mixtures has been designed, manufactured, and tested in our laboratory. The novelty of the setup is that it allows measurement of surface tension by two different methods: a modified capillary elevation method in a long vertical capillary tube and a method inspired by the approach of Hacker (National Advisory Committee for Aeronautics, Technical Note 2510, 1-20, 1951), i.e. in a short horizontal capillary tube. Functionality of all main components of the apparatus, e.g., glass chamber with the capillary tube, temperature control unit consisting of two thermostatic baths with special valves for rapid temperature jumps, helium distribution setup allowing pressure variation above the liquid meniscus inside the capillary tube, has been successfully tested. Preliminary results for the surface tension of the stable and metastable supercooled water measured by the capillary elevation method at atmospheric pressure are provided. The surface tension of water measured at temperatures between +26 °C and -11 °C is in good agreement with the extrapolated IAPWS correlation (IAPWS Release on Surface Tension of Ordinary Water Substance, September 1994); however it disagrees with data by Hacker.

Experimental test of quantum nonlocality in three-photon Greenberger-Horne-Zeilinger entanglement

Science.gov (United States)

Pan; Bouwmeester; Daniell; Weinfurter; Zeilinger

2000-02-03

Bell's theorem states that certain statistical correlations predicted by quantum physics for measurements on two-particle systems cannot be understood within a realistic picture based on local properties of each individual particle-even if the two particles are separated by large distances. Einstein, Podolsky and Rosen first recognized the fundamental significance of these quantum correlations (termed 'entanglement' by Schrodinger) and the two-particle quantum predictions have found ever-increasing experimental support. A more striking conflict between quantum mechanical and local realistic predictions (for perfect correlations) has been discovered; but experimental verification has been difficult, as it requires entanglement between at least three particles. Here we report experimental confirmation of this conflict, using our recently developed method to observe three-photon entanglement, or 'Greenberger-Horne-Zeilinger' (GHZ) states. The results of three specific experiments, involving measurements of polarization correlations between three photons, lead to predictions for a fourth experiment; quantum physical predictions are mutually contradictory with expectations based on local realism. We find the results of the fourth experiment to be in agreement with the quantum prediction and in striking conflict with local realism.

Semantic Support for Complex Ecosystem Research Environments

Science.gov (United States)

Klawonn, M.; McGuinness, D. L.; Pinheiro, P.; Santos, H. O.; Chastain, K.

2015-12-01

As ecosystems come under increasing stresses from diverse sources, there is growing interest in research efforts aimed at monitoring, modeling, and improving understanding of ecosystems and protection options. We aimed to provide a semantic infrastructure capable of representing data initially related to one large aquatic ecosystem research effort - the Jefferson project at Lake George. This effort includes significant historical observational data, extensive sensor-based monitoring data, experimental data, as well as model and simulation data covering topics including lake circulation, watershed runoff, lake biome food webs, etc. The initial measurement representation has been centered on monitoring data and related provenance. We developed a human-aware sensor network ontology (HASNetO) that leverages existing ontologies (PROV-O, OBOE, VSTO*) in support of measurement annotations. We explicitly support the human-aware aspects of human sensor deployment and collection activity to help capture key provenance that often is lacking. Our foundational ontology has since been generalized into a family of ontologies and used to create our human-aware data collection infrastructure that now supports the integration of measurement data along with simulation data. Interestingly, we have also utilized the same infrastructure to work with partners who have some more specific needs for specifying the environmental conditions where measurements occur, for example, knowing that an air temperature is not an external air temperature, but of the air temperature when windows are shut and curtains are open. We have also leveraged the same infrastructure to work with partners more interested in modeling smart cities with data feeds more related to people, mobility, environment, and living. We will introduce our human-aware data collection infrastructure, and demonstrate how it uses HASNetO and its supporting SOLR-based search platform to support data integration and semantic browsing

Combustion behaviour of pulverised wood - Numerical and experimental studies

Energy Technology Data Exchange (ETDEWEB)

Lixin Tao [TPS Termiska Processer AB, Nykoeping (Sweden)

2002-05-01

analysers. Gas-phase measurements included CO and CO{sub 2} (NDIR), O{sub 2} (paramagnetic analyser), NO (chemiluminescent detector), light hydrocarbons (THC-FID) and H{sub 2} (gas chromatography). The liquid solutions were analysed for HCN and NH{sub 3} using ion-specific electrodes. The amount of tar (heavy hydrocarbons) was determined through the measurement of TOC in the quench liquor. Solid samples were separated from the quench liquor by filtration and then analysed for their elementary fractions of C, H, O, N and ash. The experimental results are presented and discussed in this report. The presented results show that the experimental furnace and measurement facilities used in this work are generally adequate for study of pulverised wood combustion in controlled environment and provide necessary in-flame measured experimental data to support and validate the numerical models that are developed for simulation of pulverised wood combustion in furnaces and boilers. The problems occurred during the experiment are identified and future improvements are discussed.