WorldWideScience

Sample records for support on-the-fly engineering

  1. Web Services Integration on the Fly

    National Research Council Canada - National Science Library

    Leong, Hoe W

    2008-01-01

    .... Given data, software agents and supporting software infrastructure, web services integration on the fly means that human coding is not required to integrate web services into a Web Service Architecture...

  2. Engineering Technical Support Center (ETSC)

    Science.gov (United States)

    ETSC is EPA’s technical support and resource centers responsible for providing specialized scientific and engineering support to decision-makers in the Agency’s ten regional offices, states, communities, and local businesses.

  3. On the Fly Doppler Broadening Using Multipole Representation

    International Nuclear Information System (INIS)

    Khassenov, Azamat; Choi, Sooyoung; Lee, Deokjung

    2015-01-01

    On the Fly Doppler broadening is the technique to avoid pre-generation of the microscopic cross section, in other words, reduce the amount of storage. Currently, there are different types of formalisms used by NJOY code to generate reaction cross section and accomplish its Doppler broadening. Single-Level Breit-Wigner (SLBW) formalism is limited to well-separated resonances, in other words, it does not consider interference between energy levels. Multi-Level Breit- Wigner formalism (MLBW) was tested as the candidate for the cross section generation in the Monte Carlo code, which is under development in UNIST. According to the results, MLBW method requires huge amount of computational time to produce cross section at certain energy point. Reich-Moore (RM) technique can generate only 0K cross section, which means that it cannot produce broaden cross section directly from resonance parameters. The first step was to convert resonance parameters given in nuclear data file into multipoles. MPR shows very high potential to be used as the formalism in the on-the-fly Doppler broadening module of MCS. One of the main reasons is that comparison of the time cost shown in Table IV supports application of multipole representation

  4. On-the-Fly Decompression and Rendering of Multiresolution Terrain

    Energy Technology Data Exchange (ETDEWEB)

    Lindstrom, P; Cohen, J D

    2009-04-02

    We present a streaming geometry compression codec for multiresolution, uniformly-gridded, triangular terrain patches that supports very fast decompression. Our method is based on linear prediction and residual coding for lossless compression of the full-resolution data. As simplified patches on coarser levels in the hierarchy already incur some data loss, we optionally allow further quantization for more lossy compression. The quantization levels are adaptive on a per-patch basis, while still permitting seamless, adaptive tessellations of the terrain. Our geometry compression on such a hierarchy achieves compression ratios of 3:1 to 12:1. Our scheme is not only suitable for fast decompression on the CPU, but also for parallel decoding on the GPU with peak throughput over 2 billion triangles per second. Each terrain patch is independently decompressed on the fly from a variable-rate bitstream by a GPU geometry program with no branches or conditionals. Thus we can store the geometry compressed on the GPU, reducing storage and bandwidth requirements throughout the system. In our rendering approach, only compressed bitstreams and the decoded height values in the view-dependent 'cut' are explicitly stored on the GPU. Normal vectors are computed in a streaming fashion, and remaining geometry and texture coordinates, as well as mesh connectivity, are shared and re-used for all patches. We demonstrate and evaluate our algorithms on a small prototype system in which all compressed geometry fits in the GPU memory and decompression occurs on the fly every rendering frame without any cache maintenance.

  5. KESS: Knowledge Engineering Support System

    OpenAIRE

    Said, Mohamed Ben; Dougherty, Nini; Anderson, Curtis; Altman, Stanley J.; Bouhaddou, Omar; Warner, Homer R.

    1987-01-01

    KESS (Knowledge Engineering Support System) is a relational information management system created at the University of Utah to document each step in the building of four expert knowledge bases. In weekly knowledge engineering sessions, groups of experts propose decision making criteria and examine information sources in the process of creating HELP knowledge frames. KESS utilizes many-to-many links with multiple files and central link files to track the different kinds of information generate...

  6. Waterfall: Primitives Generation on the Fly

    OpenAIRE

    Chari , Guido; Garbervetsky , Diego; Bruni , Camillo; Denker , Marcus; Ducasse , Stéphane

    2013-01-01

    Modern languages are typically supported by managed runtimes (Virtual Machines). Since VMs have to deal with many concepts such as memory management, abstract execution model and scheduling, they tend to be very complex. Additionally, VMs have to meet strong performance requirements. This demand of performance is one of the main reasons why many VMs are built statically. Thus, design decisions are frozen at compile time preventing changes at runtime. One clear example is the impossibility to ...

  7. Deformation analysis of gellan-gum based bone scaffold using on-the-fly tomography

    Czech Academy of Sciences Publication Activity Database

    Kytýř, Daniel; Zlámal, Petr; Koudelka_ml., Petr; Fíla, Tomáš; Krčmářová, Nela; Kumpová, Ivana; Vavřík, Daniel; Gantar, A.; Novak, S.

    2017-01-01

    Roč. 134, November (2017), s. 400-417 ISSN 0264-1275 EU Projects: European Commission(XE) ATCZ38 - Com3d-XCT; European Commission(XE) ATCZ133 Keywords : on-the-fly tomography * gellan-gum * scaffold * digital volume correlation * compression Subject RIV: JJ - Other Materials OBOR OECD: Materials engineering Impact factor: 4.364, year: 2016 http://www.sciencedirect.com/science/article/pii/S026412751730789X

  8. On-the-fly reduction of open loops

    Energy Technology Data Exchange (ETDEWEB)

    Buccioni, Federico; Pozzorini, Stefano; Zoller, Max [Universitaet Zuerich, Physik-Institut, Zurich (Switzerland)

    2018-01-15

    Building on the open-loop algorithm we introduce a new method for the automated construction of one-loop amplitudes and their reduction to scalar integrals. The key idea is that the factorisation of one-loop integrands in a product of loop segments makes it possible to perform various operations on-the-fly while constructing the integrand. Reducing the integrand on-the-fly, after each segment multiplication, the construction of loop diagrams and their reduction are unified in a single numerical recursion. In this way we entirely avoid objects with high tensor rank, thereby reducing the complexity of the calculations in a drastic way. Thanks to the on-the-fly approach, which is applied also to helicity summation and for the merging of different diagrams, the speed of the original open-loop algorithm can be further augmented in a very significant way. Moreover, addressing spurious singularities of the employed reduction identities by means of simple expansions in rank-two Gram determinants, we achieve a remarkably high level of numerical stability. These features of the new algorithm, which will be made publicly available in a forthcoming release of the OpenLoops program, are particularly attractive for NLO multi-leg and NNLO real-virtual calculations. (orig.)

  9. On-the-fly reduction of open loops

    Science.gov (United States)

    Buccioni, Federico; Pozzorini, Stefano; Zoller, Max

    2018-01-01

    Building on the open-loop algorithm we introduce a new method for the automated construction of one-loop amplitudes and their reduction to scalar integrals. The key idea is that the factorisation of one-loop integrands in a product of loop segments makes it possible to perform various operations on-the-fly while constructing the integrand. Reducing the integrand on-the-fly, after each segment multiplication, the construction of loop diagrams and their reduction are unified in a single numerical recursion. In this way we entirely avoid objects with high tensor rank, thereby reducing the complexity of the calculations in a drastic way. Thanks to the on-the-fly approach, which is applied also to helicity summation and for the merging of different diagrams, the speed of the original open-loop algorithm can be further augmented in a very significant way. Moreover, addressing spurious singularities of the employed reduction identities by means of simple expansions in rank-two Gram determinants, we achieve a remarkably high level of numerical stability. These features of the new algorithm, which will be made publicly available in a forthcoming release of the OpenLoops program, are particularly attractive for NLO multi-leg and NNLO real-virtual calculations.

  10. UPS fellowships support creative engineering research

    OpenAIRE

    Crumbley, Liz

    2007-01-01

    A new $40,000 grant marks the 11th anniversary of support from the United Parcel Service (UPS) Foundation for doctoral fellowships in the Human Factors and Safety Engineering Graduate Program in the Grado Department of Industrial and Systems Engineering (ISE) in the College of Engineering.

  11. SAT in engineering support personnel training

    International Nuclear Information System (INIS)

    Gonzalez, M.

    1995-01-01

    The NPP engineering support functional area comprises seven common positions: reactor engineer, in-service inspection engineer, performance reliability engineer, system-maintenance engineer, station modification engineer, quality assurance engineer, and regulatory compliance engineer. The primary duties and tasks of each was presented. In Spain, a simplified SAT approach was used to analyze the training needs of these positions. The basic difference between the comprehensive SAT and the simplified method is that the simplified approach uses no taxonomy codes and the task elements are not analyzed to obtain the knowledge and skills. Resulting in an economy of time and personnel resources, this process makes use of job competencies and a top table analysis conducted by subject matter experts. An example of a JPM prepared using the simplified SAT approach was shown. Examples of the simplified approaches used in Russia, France, and USA were also discussed

  12. Engineering support strategies in the competitive environment

    International Nuclear Information System (INIS)

    Casella, L.R.; Hall, T.E.; Stark, D.R.

    1996-01-01

    This paper focuses on the innovative use of support personnel during plant outages and other maintenance/upkeep periods. At the South Texas Project the authors have formed an engineering support group specifically tailored to provide real time solutions to maintenance and operation problems. The core group consists of a cross section from the engineering disciplines and systems engineers. The group is housed in the Maintenance and Operations Facility adjacent to the power block. Close proximity and maintenance and operations personnel improves communications and response to emergent technical issues. During outages the group is augmented with additional personnel from the Design and Systems Engineering Departments. This allows for around the clock support that directly complements plant operations activities and maintenance tasks. The Thirty Minute Rule highlights urgent issues requiring engineering management attention. Dedicated twenty-four (24) hour engineering management oversight completes the engineering outage support package. Revised procedures, networks, and software enhancements, streamline the interface between engineering and work control processes. Good communications across the engineering disciplines and departments provide for enhanced teamwork and timely resolution of emergent technical issues for customers. The techniques to be described in the paper contributed directly to the South Texas Project recently establishing a new world record for a Westinghouse 3 and 4 loop pressurized water reactor refueling outage

  13. Innovation in dental education: The "On-the-Fly" approach to simultaneous development, implementation and evidence collection.

    Science.gov (United States)

    de Boer, I R; Bakker, D R; Serrano, C M; Koopman, P; Wesselink, P R; Vervoorn, J M

    2018-03-01

    This study outlines an approach for education innovation and addresses the ambivalence between evidence-based and non-evidence-based conditions. The "on-the-fly" approach was described as involving implementation during the development of an innovation for dental education. The process of designing and implementing cutting-edge technology of the MOOG Simodont Dental Trainer (DT) whilst systematically collecting evidence illustrates the "on-the-fly" approach. Using the "on-the-fly" approach for developing, implementing and collecting evidence simultaneously in an academic environment appears feasible in serving both the professionals, users and developers and system designers. During the implementation of the new technology, growing evidence stepwise strengthened its position; therefore, showing stakeholders that evidence was used to improve the technology seemed to support and increase acceptance of the new technology. When pioneering an innovative technology in a specialty field, the development stage often precedes evidence for its effectiveness. Consciously choosing the "on-the-fly" approach clarifies to stakeholders in advance about the lack of evidence in an innovation and the need of their support to collect such evidence for improvement and in order to facilitate implementation. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  14. Integrated Control System Engineering Support.

    Science.gov (United States)

    1984-12-01

    Advanced Medium Range Air to Air Missile ASTEC Advanced Speech Technology Experimental Configuration BA Body Axis BCIU Bus Control Interface Unit BMU Bus...support nreeded to tie an ASTEC speech recognition system into the DIGISYN fJcility and support an FIGR experiment designed to investigate the voice...information passed to the PDP computer consisted of integers which represented words or phrases recognized by the ASTEC recognition system. An interface

  15. Supporting indigenous women in science, technology, engineering ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Supporting indigenous women in science, technology, engineering and mathematics careers in Mexico and Central ... ROSSA's latest bulletin puts a focus on women. ... IDRC invites applications for the IDRC Doctoral Research Awards.

  16. On-the-Fly Computation of Bisimilarity Distances

    DEFF Research Database (Denmark)

    Bacci, Giorgio; Bacci, Giovanni; Larsen, Kim Guldstrand

    2017-01-01

    of Desharnais et al. between discrete-time Markov chains as an optimal solution of a linear program that can be solved by using the ellipsoid method. Inspired by their result, we propose a novel linear program characterization to compute the distance in the continuous-time setting. Differently from previous......We propose a distance between continuous-time Markov chains (CTMCs) and study the problem of computing it by comparing three different algorithmic methodologies: iterative, linear program, and on-the-fly. In a work presented at FoSSaCS'12, Chen et al. characterized the bisimilarity distance...... proposals, ours has a number of constraints that is bounded by a polynomial in the size of the CTMC. This, in particular, proves that the distance we propose can be computed in polynomial time. Despite its theoretical importance, the proposed linear program characterization turns out to be inefficient...

  17. On-the-fly augmented reality for orthopedic surgery using a multimodal fiducial.

    Science.gov (United States)

    Andress, Sebastian; Johnson, Alex; Unberath, Mathias; Winkler, Alexander Felix; Yu, Kevin; Fotouhi, Javad; Weidert, Simon; Osgood, Greg; Navab, Nassir

    2018-04-01

    Fluoroscopic x-ray guidance is a cornerstone for percutaneous orthopedic surgical procedures. However, two-dimensional (2-D) observations of the three-dimensional (3-D) anatomy suffer from the effects of projective simplification. Consequently, many x-ray images from various orientations need to be acquired for the surgeon to accurately assess the spatial relations between the patient's anatomy and the surgical tools. We present an on-the-fly surgical support system that provides guidance using augmented reality and can be used in quasiunprepared operating rooms. The proposed system builds upon a multimodality marker and simultaneous localization and mapping technique to cocalibrate an optical see-through head mounted display to a C-arm fluoroscopy system. Then, annotations on the 2-D x-ray images can be rendered as virtual objects in 3-D providing surgical guidance. We quantitatively evaluate the components of the proposed system and, finally, design a feasibility study on a semianthropomorphic phantom. The accuracy of our system was comparable to the traditional image-guided technique while substantially reducing the number of acquired x-ray images as well as procedure time. Our promising results encourage further research on the interaction between virtual and real objects that we believe will directly benefit the proposed method. Further, we would like to explore the capabilities of our on-the-fly augmented reality support system in a larger study directed toward common orthopedic interventions.

  18. On-the-fly doppler broadening for Monte Carlo codes

    International Nuclear Information System (INIS)

    Yesilyurt, G.; Martin, W. R.; Brown, F. B.

    2009-01-01

    A methodology to allow on-the-fly Doppler broadening of neutron cross sections for use in Monte Carlo codes has been developed. The Monte Carlo code only needs to store 0 K cross sections for each isotope and the method will broaden the 0 K cross sections for any isotope in the library to any temperature in the range 77 K-3200 K. The methodology is based on a combination of Taylor series expansions and asymptotic series expansions. The type of series representation was determined by investigating the temperature dependence of U3o8 resonance cross sections in three regions: near the resonance peaks, mid-resonance, and the resonance wings. The coefficients for these series expansions were determined by a regression over the energy and temperature range of interest. Since the resonance parameters are a function of the neutron energy and target nuclide, the ψ and χ functions in the Adler-Adler multi-level resonance model can be represented by series expansions in temperature only, allowing the least number of terms to approximate the temperature dependent cross sections within a given accuracy. The comparison of the broadened cross sections using this methodology with the NJOY cross sections was excellent over the entire temperature range (77 K-3200 K) and energy range. A Monte Carlo code was implemented to apply the combined regression model and used to estimate the additional computing cost which was found to be less than <1%. (authors)

  19. Enterprise Engineering Method supporting Six Sigma Approach

    OpenAIRE

    Jochem, Roland

    2007-01-01

    Enterprise Modeling (EM) is currently in operation either as a technique to represent and understand the structure and behavior of the enterprise, or as a technique to analyze business processes, and in many cases as support technique for business process reengineering. However, EM architectures and methodes for Enterprise Engineering can also used to support new management techniques like SIX SIGMA, because these new techniques need a clear, transparent and integrated definition and descript...

  20. Engineering Technical Support Center Annual Report Fiscal ...

    Science.gov (United States)

    The United States Environmental Protection Agency (EPA or Agency) Office of Research and Development (ORD) created the Engineering Technical Support Center (ETSC) in 1987, one of several technical support centers created as part of the Technical Support Project (TSP). ETSC provides engineering expertise to Agency program and regional offices and remediation teams working at contaminated sites across the country. The ETSC is operated within ORD’s Land Remediation and Pollution Control Division (LRPCD) of the National Risk Management Research Laboratory (NRMRL) in Cincinnati, Ohio. The ETSC’s mission is to provide site-specific scientific and engineering technical support to Remedial Project Managers, On-Scene Coordinators, and other remediation personnel at contaminated sites. This allows local, regional, or national authorities to work more quickly, efficiently, and cost effectively, while also increasing the technical experience of the remediation team. Since its inception, the ETSC has supported countless projects across all EPA Regions in almost all states and territories. This report highlights significant projects the ETSC supported in fiscal year 2015 (FY15). These projects addressed an array of environmental scenarios, such as remote mining contamination, expansive landfill waste, cumulative impacts from multiple contamination sources, and persistent threats from abandoned industrial sites. Constructing and testing new and innovative treatment technol

  1. Virtualization-support Cases in Engineering Education

    DEFF Research Database (Denmark)

    Soler, José

    2011-01-01

    The paper presents cases of applying hardware virtualization techniques as support for education activities in two different courses and a master thesis within the degree International MSc on Telecommunication Engineering at the Technical University of Denmark (DTU). The triggering problem...... is presented in each of the cases, together with the benefits and drawbacks of using virtualization to cope with it....

  2. Modeling uncertainty in requirements engineering decision support

    Science.gov (United States)

    Feather, Martin S.; Maynard-Zhang, Pedrito; Kiper, James D.

    2005-01-01

    One inherent characteristic of requrements engineering is a lack of certainty during this early phase of a project. Nevertheless, decisions about requirements must be made in spite of this uncertainty. Here we describe the context in which we are exploring this, and some initial work to support elicitation of uncertain requirements, and to deal with the combination of such information from multiple stakeholders.

  3. DATYS integrates piping and supports engineering

    International Nuclear Information System (INIS)

    Rendon, J.G.; Fraile, A.R.

    1990-01-01

    Empresarios Agrupados of Spain has developed an interactive software package which computerizes and integrates the whole range of tasks involved in pipework engineering; including drawing, design, analysis and support calculations. Its strength lies in its modularity and in the ability to re-evaluate and modify existing projects. (author)

  4. Efficient On-the-fly Algorithms for the Analysis of Timed Games

    DEFF Research Database (Denmark)

    Cassez, Franck; David, Alexandre; Fleury, Emmanuel

    2005-01-01

    In this paper, we propose the first efficient on-the-fly algorithm for solving games based on timed game automata with respect to reachability and safety properties The algorithm we propose is a symbolic extension of the on-the-fly algorithm suggested by Liu & Smolka [15] for linear-time model-ch...... symbolic algorithm are proposed as well as methods for obtaining time-optimal winning strategies (for reachability games). Extensive evaluation of an experimental implementation of the algorithm yields very encouraging performance results.......In this paper, we propose the first efficient on-the-fly algorithm for solving games based on timed game automata with respect to reachability and safety properties The algorithm we propose is a symbolic extension of the on-the-fly algorithm suggested by Liu & Smolka [15] for linear-time model...

  5. A probabilistic coverage for on-the-fly test generation algorithms

    OpenAIRE

    Goga, N.

    2003-01-01

    This paper describes a way to compute the coverage for an on-the-fly test generation algorithm based on a probabilistic approach. The on-the-fly test generation and execution process and the development process of an implementation from a specification are viewed as a stochastic process. The probabilities of the stochastic processes are integrated in a generalized definition of coverage. The generalized formulas are instantiated for the ioco theory and for the specification of the TorX test g...

  6. Engineering, Analysis and Technology FY 1995 Site Support Program Plan

    International Nuclear Information System (INIS)

    Suyama, R.M.

    1994-09-01

    The vision of the Engineering, Analysis and Technology organization is to be recognized as the cost-effective supplier of specialized, integrated, multi-disciplined engineering teams to support Hanford missions. The mission of the Engineering, Analysis and Technology organization is to provide centralized engineering services. These services are focused on supplying technical design, analytical engineering and related support services that support Hanford's environmental restoration mission. These services include engineering analysis, design and development of systems and engineered equipment, supplying multi-disciplined engineering teams to all Hanford programs and project organizations, engineering document release, and site-wide leadership in the development and implementation of engineering standards, engineering practices, and configuration management processes

  7. Space Life-Support Engineering Program

    Science.gov (United States)

    Seagrave, Richard C. (Principal Investigator)

    1995-01-01

    This report covers the seventeen months of work performed under an extended one year NASA University Grant awarded to Iowa State University to perform research on topics relating to the development of closed-loop long-term life support systems with the initial principal focus on space water management. In the first phase of the program, investigators from chemistry and chemical engineering with demonstrated expertise in systems analysis, thermodynamics, analytical chemistry and instrumentation, performed research and development in two major related areas; the development of low-cost, accurate, and durable sensors for trace chemical and biological species, and the development of unsteady-state simulation packages for use in the development and optimization of control systems for life support systems. In the second year of the program, emphasis was redirected towards concentrating on the development of dynamic simulation techniques and software and on performing a thermodynamic systems analysis, centered on availability or energy analysis, in an effort to begin optimizing the systems needed for water purification. The third year of the program, the subject of this report, was devoted to the analysis of the water balance for the interaction between humans and the life support system during space flight and exercise, to analysis of the cardiopulmonary systems of humans during space flight, and to analysis of entropy production during operation of the air recovery system during space flight.

  8. On-the-fly auditing of business processes

    NARCIS (Netherlands)

    Hee, van K.M.; Hidders, A.J.H.; Houben, G.J.P.M.; Paredaens, J.; Thiran, P.A.P.; Jensen, K.; Donatelli, S.; Koutny, M.

    2010-01-01

    Information systems supporting business processes are usually very complex. If we have to ensure that certain business rules are enforced in a business process, it is often easier to design a separate system, called a monitor, that collects the events of the business processes and verifies whether

  9. On-the-fly auditing of business processes

    NARCIS (Netherlands)

    Hee, van K.M.; Hidders, A.J.H.; Houben, G.J.P.M.; Paredaens, J.; Thiran, P.A.P.

    2009-01-01

    Information systems supporting business process are mostly very complex. If we have to ensure that certain business rules are enforced in a business process, it is often easier to design a separate system, called a monitor, that collects the events of the business processes and verifies whether the

  10. Prioritization of engineering support requests and advanced technology projects using decision support and industrial engineering models

    Science.gov (United States)

    Tavana, Madjid

    1995-01-01

    The evaluation and prioritization of Engineering Support Requests (ESR's) is a particularly difficult task at the Kennedy Space Center (KSC) -- Shuttle Project Engineering Office. This difficulty is due to the complexities inherent in the evaluation process and the lack of structured information. The evaluation process must consider a multitude of relevant pieces of information concerning Safety, Supportability, O&M Cost Savings, Process Enhancement, Reliability, and Implementation. Various analytical and normative models developed over the past have helped decision makers at KSC utilize large volumes of information in the evaluation of ESR's. The purpose of this project is to build on the existing methodologies and develop a multiple criteria decision support system that captures the decision maker's beliefs through a series of sequential, rational, and analytical processes. The model utilizes the Analytic Hierarchy Process (AHP), subjective probabilities, the entropy concept, and Maximize Agreement Heuristic (MAH) to enhance the decision maker's intuition in evaluating a set of ESR's.

  11. On-the-Fly Kinetic Monte Carlo Simulation of Aqueous Phase Advanced Oxidation Processes.

    Science.gov (United States)

    Guo, Xin; Minakata, Daisuke; Crittenden, John

    2015-08-04

    We have developed an on-the-fly kinetic Monte Carlo (KMC) model to predict the degradation mechanisms and fates of intermediates and byproducts that are produced during aqueous-phase advanced oxidation processes (AOPs). The on-the-fly KMC model is composed of a reaction pathway generator, a reaction rate constant estimator, a mechanistic reduction module, and a KMC solver. The novelty of this work is that we develop the pathway as we march forward in time rather than developing the pathway before we use the KMC method to solve the equations. As a result, we have fewer reactions to consider, and we have greater computational efficiency. We have verified this on-the-fly KMC model for the degradation of polyacrylamide (PAM) using UV light and titanium dioxide (i.e., UV/TiO2). Using the on-the-fly KMC model, we were able to predict the time-dependent profiles of the average molecular weight for PAM. The model provided detailed and quantitative insights into the time evolution of the molecular weight distribution and reaction mechanism. We also verified our on-the-fly KMC model for the destruction of (1) acetone, (2) trichloroethylene (TCE), and (3) polyethylene glycol (PEG) for the ultraviolet light and hydrogen peroxide AOP. We demonstrated that the on-the-fly KMC model can achieve the same accuracy as the computer-based first-principles KMC (CF-KMC) model, which has already been validated in our earlier work. The on-the-fly KMC is particularly suitable for molecules with large molecular weights (e.g., polymers) because the degradation mechanisms for large molecules can result in hundreds of thousands to even millions of reactions. The ordinary differential equations (ODEs) that describe the degradation pathways cannot be solved using traditional numerical methods, but the KMC can solve these equations.

  12. On-the-fly ab initio semiclassical dynamics: Emission spectra of oligothiophenes

    Science.gov (United States)

    Wehrle, Marius; Sulc, Miroslav; Vanicek, Jiri

    2014-03-01

    We employ the thawed Gaussian approximation (TGA) [E. J. Heller, J. Chem. Phys. 62, 1544 (1975)] within an on-the-fly ab initio (OTF-AI) scheme to calculate the vibrationally resolved emission spectra of oligothiophenes up to five rings. OTF-AI-TGA is efficient enough to treat all vibrational degrees of freedom on an equal footing even in case of 5-oligothiophene (105 vibrational degrees of freedom), thus obviating the need for the crude global harmonic approximation, popular for large system. The experimental emission spectra have been almost perfectly reproduced. In order to provide a deeper insight into the associated physical and chemical processes, we present a systematic approach to assess the importance and to analyze the mutual coupling of individual vibrational degrees of freedom during the dynamics. This allows us to explain the changes in the vibrational line shapes of the oligothiophenes with increasing number of rings. Furthermore, we observe the dynamical interplay between quinoid and aromatic characters of individual rings in the oligothiophene chain during the dynamics and confirm that the quinoid character prevails in the center of the chain. This research was supported by the Swiss NSF Grant No. 200021_124936/1 and NCCR Molecular Ultrafast Science & Technology (MUST), and by the EPFL.

  13. Lecture 11: Systemtap : Patching the linux kernel on the fly

    CERN Multimedia

    CERN. Geneva

    2013-01-01

    The presentation will describe the usage of Systemtap, in CERN Scientific Linux environment. Systemtap is a tool that allows developers and administrators to write and reuse simple scripts to deeply examine the activities of a live Linux system. We will go through the life cycle of a system tap module : creation, packaging, deployment. It will focus on how we used it recently at CERN as a workaround to patch a 0-day. Thomas Oulevey is a member if the IT department at CERN where he is an active member of the Linux team which supports 9’000 servers, 3’000 desktop systems and more than 5’000 active users. Before CERN he worked at the former astrophysics department of CERN, now called the European Southern Observatory, based in Chile. He was used to maintain the core telescope Linux systems and monitoring infrastructure.

  14. Learning on the fly with the analogical method

    Directory of Open Access Journals (Sweden)

    Zara Mehrnoosh

    2016-04-01

    Full Text Available Today in Italy 20-25% of students in primary school is reported to have difficulties with mathematical skills, although several researchers have noticed a man’s natural predisposition towards numbers. In the light of this high number of reports becomes therefore necessary to reconsider the didactic context to better support the natural evolution of numerical and mathematical cognition from early childhood. The following article presents the analogical method developed by Camillo Bortolato: non-conceptual didactic path focused on semantic process, subitizing and mental math. Apprendere al volo con il metodo analogicoAd oggi in Italia il 20-25% degli alunni nella scuola primaria viene segnalato per difficoltà nel calcolo, nonostante diversi ricercatori abbiano evidenziato una naturale predisposizione dell’uomo verso la numerosità. Alla luce di questo elevato numero di segnalazioni diviene necessario ripensare il contesto didattico per sostenere al meglio e fin dalla prima infanzia la naturale evoluzione della cognizione numerica e di calcolo. Nel seguente articolo viene presentato il metodo analogico di Camillo Bortolato, un percorso didattico non concettuale attento ai processi semantici, al ruolo del subitizing e del calcolo a mente.

  15. On the fly quantum dynamics of electronic and nuclear wave packets

    Science.gov (United States)

    Komarova, Ksenia G.; Remacle, F.; Levine, R. D.

    2018-05-01

    Multielectronic states quantum dynamics on a grid is described in a manner motivated by on the fly classical trajectory computations. Non stationary electronic states are prepared by a few cycle laser pulse. The nuclei respond and begin moving. We solve the time dependent Schrödinger equation for the electronic and nuclear dynamics for excitation from the ground electronic state. A satisfactory accuracy is possible using a localized description on a discrete grid. This enables computing on the fly for both the nuclear and electronic dynamics including non-adiabatic couplings. Attosecond dynamics in LiH is used as an example.

  16. Membrane supported scaffold architectures for tissue engineering

    NARCIS (Netherlands)

    Bettahalli Narasimha, M.S.

    2011-01-01

    Tissue engineering aims at restoring or regenerating a damaged tissue. Often the tissue recreation occurs by combining cells, derived from a patient biopsy, onto a 3D porous matrix, functioning as a scaffold. One of the current limitations of tissue engineering is the inability to provide sufficient

  17. Engineering to support wellbeing of dairy animals.

    Science.gov (United States)

    Caja, Gerardo; Castro-Costa, Andreia; Knight, Christopher H

    2016-05-01

    Current trends in the global milk market and the recent abolition of milk quotas have accelerated the trend of the European dairy industry towards larger farm sizes and higher-yielding animals. Dairy cows remain in focus, but there is a growing interest in other dairy species, whose milk is often directed to traditional and protected designation of origin and gourmet dairy products. The challenge for dairy farms in general is to achieve the best possible standards of animal health and welfare, together with high lactational performance and minimal environmental impact. For larger farms, this may need to be done with a much lower ratio of husbandry staff to animals. Recent engineering advances and the decreasing cost of electronic technologies has allowed the development of 'sensing solutions' that automatically collect data, such as physiological parameters, production measures and behavioural traits. Such data can potentially help the decision making process, enabling early detection of health or wellbeing problems in individual animals and hence the application of appropriate corrective husbandry practices. This review focuses on new knowledge and emerging developments in welfare biomarkers (e.g. stress and metabolic diseases), activity-based welfare assessment (e.g. oestrus and lameness detection) and sensors of temperature and pH (e.g. calving alert and rumen function) and their combination and integration into 'smart' husbandry support systems that will ensure optimum wellbeing for dairy animals and thereby maximise farm profitability. Use of novel sensors combined with new technologies for information handling and communication are expected to produce dramatic changes in traditional dairy farming systems.

  18. Collaborative engineering-design support system

    Science.gov (United States)

    Lee, Dong HO; Decker, D. Richard

    1994-01-01

    Designing engineering objects requires many engineers' knowledge from different domains. There needs to be cooperative work among engineering designers to complete a design. Revisions of a design are time consuming, especially if designers work at a distance and with different design description formats. In order to reduce the design cycle, there needs to be a sharable design describing the engineering community, which can be electronically transportable. Design is a process of integrating that is not easy to define definitively. This paper presents Design Script which is a generic engineering design knowledge representation scheme that can be applied in any engineering domain. The Design Script is developed through encapsulation of common design activities and basic design components based on problem decomposition. It is implemented using CLIPS with a Windows NT graphical user interface. The physical relationships between engineering objects and their subparts can be constructed in a hierarchical manner. The same design process is repeatedly applied at each given level of hierarchy and recursively into lower levels of the hierarchy. Each class of the structure can be represented using the Design Script.

  19. Providing Co-Curricular Support: A Multi-Case Study of Engineering Student Support Centers

    Science.gov (United States)

    Lee, Walter C., Jr.

    2015-01-01

    In response to the student retention and diversity issues that have been persistent in undergraduate engineering education, many colleges have developed Engineering Student Support Centers (ESSCs) such as Minority Engineering Programs (MEPs) and Women in Engineering Programs (WEPs). ESSCs provide underrepresented students with co-curricular…

  20. Implementation of the On-the-fly Encryption for the Linux OS Based on Certified CPS

    Directory of Open Access Journals (Sweden)

    Alexander Mikhailovich Korotin

    2013-02-01

    Full Text Available The article is devoted to tools for on-the-fly encryption and a method to implement such tool for the Linux OS based on a certified CPS.The idea is to modify the existing tool named eCryptfs. Russian cryptographic algorithms will be used in the user and kernel modes.

  1. Extended Adaptive Biasing Force Algorithm. An On-the-Fly Implementation for Accurate Free-Energy Calculations.

    Science.gov (United States)

    Fu, Haohao; Shao, Xueguang; Chipot, Christophe; Cai, Wensheng

    2016-08-09

    Proper use of the adaptive biasing force (ABF) algorithm in free-energy calculations needs certain prerequisites to be met, namely, that the Jacobian for the metric transformation and its first derivative be available and the coarse variables be independent and fully decoupled from any holonomic constraint or geometric restraint, thereby limiting singularly the field of application of the approach. The extended ABF (eABF) algorithm circumvents these intrinsic limitations by applying the time-dependent bias onto a fictitious particle coupled to the coarse variable of interest by means of a stiff spring. However, with the current implementation of eABF in the popular molecular dynamics engine NAMD, a trajectory-based post-treatment is necessary to derive the underlying free-energy change. Usually, such a posthoc analysis leads to a decrease in the reliability of the free-energy estimates due to the inevitable loss of information, as well as to a drop in efficiency, which stems from substantial read-write accesses to file systems. We have developed a user-friendly, on-the-fly code for performing eABF simulations within NAMD. In the present contribution, this code is probed in eight illustrative examples. The performance of the algorithm is compared with traditional ABF, on the one hand, and the original eABF implementation combined with a posthoc analysis, on the other hand. Our results indicate that the on-the-fly eABF algorithm (i) supplies the correct free-energy landscape in those critical cases where the coarse variables at play are coupled to either each other or to geometric restraints or holonomic constraints, (ii) greatly improves the reliability of the free-energy change, compared to the outcome of a posthoc analysis, and (iii) represents a negligible additional computational effort compared to regular ABF. Moreover, in the proposed implementation, guidelines for choosing two parameters of the eABF algorithm, namely the stiffness of the spring and the mass

  2. Engineering Technical Support Center Annual Report Fiscal Year 2015

    Science.gov (United States)

    The United States Environmental Protection Agency (EPA or Agency) Office of Research and Development (ORD) created the Engineering Technical Support Center (ETSC) in 1987, one of several technical support centers created as part of the Technical Support Project (TSP). ETSC provid...

  3. LED provides engineering and electrooptics support to the Laser Program

    International Nuclear Information System (INIS)

    Pehrson, D.

    1985-01-01

    The work of the Laser Engineering Division is reviewed. The division provides engineering and electrooptics support to the laser program. The laser program has been an integral part of the efforts to explore the potential of lasers in harnessing thermonuclear fusion for energy and for defense-related physics studies and in efficiently separating fissile fuels

  4. Electrical engineering research support for FDOT Traffic Statistics Office

    Science.gov (United States)

    2010-03-01

    The aim of this project was to provide electrical engineering support for the telemetered traffic monitoring sites (TTMSs) operated by the Statistics Office of the Florida Department of Transportation. This project was a continuation of project BD-54...

  5. Engineering to support wellbeing of dairy animals

    DEFF Research Database (Denmark)

    Caja, Gerardo; Castro-Costa, Andreia; Knight, Christopher Harold

    2016-01-01

    Current trends in the global milk market and the recent abolition of milk quotas have accelerated the trend of the European dairy industry towards larger farm sizes and higher-yielding animals. Dairy cows remain in focus, but there is a growing interest in other dairy species, whose milk is often...... directed to traditional and protected designation of origin and gourmet dairy products. The challenge for dairy farms in general is to achieve the best possible standards of animal health and welfare, together with high lactational performance and minimal environmental impact. For larger farms, this may...... need to be done with a much lower ratio of husbandry staff to animals. Recent engineering advances and the decreasing cost of electronic technologies has allowed the development of 'sensing solutions' that automatically collect data, such as physiological parameters, production measures and behavioural...

  6. Engineering Task Plan for Routine Engineering Support for Core Sampler System

    International Nuclear Information System (INIS)

    BOGER, R.M.

    1999-01-01

    Routine engineering support is required during normal operation of the core sampler trucks and associated ancillary equipment. This engineering support consists of, but is not limited to, troubleshooting operation problems, correcting minor design problems, assistance with work package preparation, assistance with procurement, fabrication shop support, planning of engineering tasks and preparation of associated Engineering Task Plans (ETP) and Engineering Service Requests (ESR). This ETP is the management plan document for implementing routine engineering support. Any additional changes to the scope of this ETP shall require a Letter of Instruction from Lockheed Martin Hanford Corp (LMHC). This document will also be the Work Planning Document for Development Control (HNF 1999a). The scope of this task will be to provide routine engineering support for Characterization equipment as required to support Characterization Operations. A task by task decision will be made by management to determine which tasks will be done per this ETP and if additional ETPs and/or ESRs are required. Due to the unique nature of this task, the only identifiable deliverable is to provide support as requested. Deliverables will be recorded in a task logbook as activities are identified. ESRs will be generated for tasks that require more than 40 person hours to complete, per Characterization Engineering Desk Instructions (DI 1999a)

  7. IT logistics support life cycle of products in air engine

    Directory of Open Access Journals (Sweden)

    М.С. Кулик

    2009-02-01

    Full Text Available  Questions of increase of efficiency of a supply with information of creation and support in operation of modern aviation engines are considered. The revealed most perspective directions of development of complex systems of support of life cycle aviation technics.

  8. The Systems Engineering Process for Human Support Technology Development

    Science.gov (United States)

    Jones, Harry

    2005-01-01

    Systems engineering is designing and optimizing systems. This paper reviews the systems engineering process and indicates how it can be applied in the development of advanced human support systems. Systems engineering develops the performance requirements, subsystem specifications, and detailed designs needed to construct a desired system. Systems design is difficult, requiring both art and science and balancing human and technical considerations. The essential systems engineering activity is trading off and compromising between competing objectives such as performance and cost, schedule and risk. Systems engineering is not a complete independent process. It usually supports a system development project. This review emphasizes the NASA project management process as described in NASA Procedural Requirement (NPR) 7120.5B. The process is a top down phased approach that includes the most fundamental activities of systems engineering - requirements definition, systems analysis, and design. NPR 7120.5B also requires projects to perform the engineering analyses needed to ensure that the system will operate correctly with regard to reliability, safety, risk, cost, and human factors. We review the system development project process, the standard systems engineering design methodology, and some of the specialized systems analysis techniques. We will discuss how they could apply to advanced human support systems development. The purpose of advanced systems development is not directly to supply human space flight hardware, but rather to provide superior candidate systems that will be selected for implementation by future missions. The most direct application of systems engineering is in guiding the development of prototype and flight experiment hardware. However, anticipatory systems engineering of possible future flight systems would be useful in identifying the most promising development projects.

  9. College-Wide Support | College of Engineering & Applied Science

    Science.gov (United States)

    Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

  10. Efficient on-the-fly Algorithm for Checking Alternating Timed Simulation

    DEFF Research Database (Denmark)

    David, Alexandre; Larsen, Kim Guldstrand; Chatain, Thomas

    2009-01-01

    In this paper we focus on property-preserving preorders between timed game automata and their application to control of partially observable systems. We define timed weak alternating simulation as a preorder between timed game automata, which preserves controllability. We define the rules...... of building a symbolic turn-based two-player game such that the existence of a winning strategy is equivalent to the simulation being satisfied. We also propose an on-the-fly algorithm for solving this game. This simulation checking method can be applied to the case of non-alternating or strong simulations...

  11. On-the-Fly Control of High-Harmonic Generation Using a Structured Pump Beam

    Science.gov (United States)

    Hareli, Liran; Lobachinsky, Lilya; Shoulga, Georgiy; Eliezer, Yaniv; Michaeli, Linor; Bahabad, Alon

    2018-05-01

    We demonstrate experimentally a relatively simple yet powerful all-optical enhancement and control technique for high harmonic generation. This is achieved by using as a pump beam two different spatial optical modes interfering together to realize tunable periodic quasi-phase matching of the interaction. With this technique, we demonstrate on-the-fly quasi-phase matching of harmonic orders 29-41 at ambient gas pressure levels of 50 and 100 Torr, where an up to 100-fold enhancement of the emission is observed. The technique is scalable to different harmonic orders and ambient pressure conditions.

  12. Targeted initiatives. Support for nuclear engineering education in the USA

    International Nuclear Information System (INIS)

    Gutteridge, John

    2001-01-01

    Recruitment and education of a new generation of nuclear engineers stands to benefit in the USA from a range of programmes involving governmental bodies, universities, and industry groups. They are part of efforts to attract more students to consider and prepare for careers in the nuclear industry, and to provide financial support for nuclear research and education. Career prospects in the nuclear field are brightening. The demand for nuclear engineers and nuclear trained personnel is on the rise as the new century opens. During the past year several studies were completed in an attempt to ascertain the problems in nuclear engineering education and define initiatives to address these problems

  13. Annular tidal regenerator engine for nuclear circulatory support systems

    International Nuclear Information System (INIS)

    Hagen, K.G.; Ruggles, A.E.; Fam, S.S.; Torti, V.A.

    1975-01-01

    In order to simplify the configuration of the tidal regenerator engine nuclear-powered circulatory support system, thereby drastically reducing its size and improving the intrinsic reliability, the engine has been redesigned. This redesign focuses on allowing power to be extracted at the low temperature end of the engine utilizing a piston-cylinder arrangement wherein all of the necessary heat transfer processes occur in the annular gap between the piston and cylinder. In all other respects the engine retains its basic characteristics as a hybrid between a Stirling engine and a Rankine engine. A significant advantage of the new arrangement is the ability to raise the superheat temperature limit from 650 0 F to over 900 0 F. This has yielded an increase in engine efficiency from 10 percent to 14 percent, and further increases are anticipated by utilizing an expansion and/or a binary version of the engine. The implantable system volume has been reduced by a factor of three and orientation insensitivity with respect to gravity has been demonstrated. Many system components have already demonstrated endurances of several thousand hours

  14. Hydrophobic Janus Foam Motors: Self-Propulsion and On-The-Fly Oil Absorption

    Directory of Open Access Journals (Sweden)

    Xiaofeng Li

    2018-01-01

    Full Text Available In this work, we for the first time have proposed and fabricated a self-propelled Janus foam motor for on-the-fly oil absorption on water by simply loading camphor/stearic acid (SA mixture as fuels into one end of the SA-modified polyvinyl alcohol (PVA foam. The as-fabricated Janus foam motors show an efficient Marangoni effect-based self-propulsion on water for a long lifetime due to the effective inhibition of the rapid release of camphor by the hydrophobic SA in the fuel mixture. Furthermore, they can automatically search, capture, and absorb oil droplets on the fly, and then be spontaneously self-assembled after oil absorption due to the self-propulsion of the motors as well as the attractive capillary interactions between the motors and oil droplets. This facilitates the subsequent collection of the motors from water after the treatment. Since the as-developed Janus foam motors can effectively integrate intriguing behaviors of the self-propulsion, efficient oil capture, and spontaneous self-assembly, they hold great promise for practical applications in water treatment.

  15. On-the-fly Data Reprocessing and Analysis Capabilities from the XMM-Newton Archive

    Science.gov (United States)

    Ibarra, A.; Sarmiento, M.; Colomo, E.; Loiseau, N.; Salgado, J.; Gabriel, C.

    2017-10-01

    The XMM-Newton Science Archive (XSA) includes since last release the possibility to perform on-the-fly data processing with SAS through the Remote Interface for Science Analysis (RISA) server. It enables scientists to analyse data without any download and installation of data and software. The analysis options presently available include extraction of spectra and light curves of user-defined EPIC source regions and full reprocessing of data for which currently archived pipeline products were processed with older SAS versions or calibration files. The current pipeline is fully aligned with the most recent SAS and calibration, while the last full reprocessing of the archive was performed in 2013. The on-the-fly data processing functionality in this release is an experimental version and we invite the community to test and let us know their results. Known issues and workarounds are described in the 'Watchouts' section of the XSA web page. Feedback on how this functionality should evolve will be highly appreciated.

  16. Training of engineering support personnel at North Carolina State University

    International Nuclear Information System (INIS)

    Bohannon, J.R. Jr.

    1975-01-01

    The sources of planning for the development of curricula for engineering support personnel for the nuclear industry in general and nuclear facilities in particular have included the deliberate acquisition of inputs from employers, feedback from past students, and the critique of curricula by the industry, students, and faculty. As a result, three principal courses were developed in the Department of Nuclear Engineering, namely, Reactor Systems which deals in terms of the design engineer's and owner's concerns with regard to functional requirements, design criteria, and objectives of reactor systems; Reactor Operations which applies the student's basic engineering education to the role of an engineer in nuclear facilities, with particular attention to power plant operations; and Quality Assurance which provides the student with the bases, engineering implications and engineer's role in quality assurance during the design, construction, delivery and operation of nuclear and other complex facilities. A summary of the results to date of this trinity of courses is presented, with particular attention to its acceptance by the industry

  17. A Mathematics Support Programme for First-Year Engineering Students

    Science.gov (United States)

    Hillock, Poh Wah; Jennings, Michael; Roberts, Anthony; Scharaschkin, Victor

    2013-01-01

    This article describes a mathematics support programme at the University of Queensland, targeted at first-year engineering students identified as having a high risk of failing a first-year mathematics course in calculus and linear algebra. It describes how students were identified for the programme and the main features of the programme. The…

  18. A Gaussian decision-support tool for engineering design process

    NARCIS (Netherlands)

    Rajabali Nejad, Mohammadreza; Spitas, Christos

    2013-01-01

    Decision-making in design is of great importance, resulting in success or failure of a system (Liu et al., 2010; Roozenburg and Eekels, 1995; Spitas, 2011a). This paper describes a robust decision-support tool for engineering design process, which can be used throughout the design process in either

  19. Supportive Organisational Cultures and their effects on Male Civil Engineers

    Directory of Open Access Journals (Sweden)

    Valarie Francis

    2012-11-01

    Full Text Available Substantial changes, not only in the demographic composition of the Australian workforce, but also,in the roles and expectations of men and women, have led to organisational and employee attempts to reconcile work and non-work demands. Research suggests that when work-family balance practices are introduced they can greatly enhance organisational efficency. However factors embedded in the organisational culture can undermine these policies rendering them ineffective. This quantitative study examined the relationship between the perceptions of a supportive work culture and some work and non-work experiences of Australian male civil engineers. The research investigated the prevalence of organisational values supportive of work-life balances as well as the level of work-family conflict perceived by those engineers. This paper reports some initial results of the study. These indicated that male civil engineers experienced moderate levels of work-family conflict but do not perceive their organisations to be very supportive of employee nneeds to balance work and personal life. However those that reported a supportive work environment also reported higher levels of organisational commitment, greater job and life satisfaction as well as lower level of work-family conflict and lower intentions to quit. The implications of the findings for organisations employing civil engineers are discussed.

  20. Supportive Organisational Cultures and their effects on Male Civil Engineers

    Directory of Open Access Journals (Sweden)

    Valarie Francis

    2012-11-01

    Full Text Available Substantial changes, not only in the demographic composition of the Australian workforce, but also,in the roles and expectations of men and women, have led to organisational and employee attempts to reconcile work and non-work demands. Research suggests that when work-family balance practices are introduced they can greatly enhance organisational efficency. However factors embedded in the organisational culture can undermine these policies rendering them ineffective. This quantitative study examined the relationship between the perceptions of a supportive work culture and some work and non-work experiences of Australian male civil engineers. The research investigated the prevalence of organisational values supportive of work-life balances as well as the level of work-family conflict perceived by those engineers. This paper reports some initial results of the study. These indicated that male civil engineers experienced moderate levels of work-family conflict but do not perceive their organisations to be very supportive of employee nneeds to balance work and personal life. However those that reported a supportive work environment also reported higher levels of organisational commitment, greater job and life satisfaction as well as lower level of work-family conflict and lower intentions to quit. The implications of the findings for organisations employing civil engineers are discussed.   

  1. Exploring Engineering instructors' views about writing and online tools to support communication in Engineering

    Science.gov (United States)

    Howard, Sarah K.; Khosronejad, Maryam; Calvo, Rafael A.

    2017-11-01

    To be fully prepared for the professional workplace, Engineering students need to be able to effectively communicate. However, there has been a growing concern in the field about students' preparedness for this aspect of their future work. It is argued that online writing tools, to engage numbers of students in the writing process, can support feedback on and development of writing in engineering on a larger scale. Through interviews and questionnaires, this study explores engineering academics' perceptions of writing to better understand how online writing tools may be integrated into their teaching. Results suggest that writing is viewed positively in the discipline, but it is not believed to be essential to success in engineering. Online writing tools were believed to support a larger number of students, but low knowledge of the tools limited academics' understanding of their usefulness in teaching and learning. Implications for innovation in undergraduate teaching are discussed.

  2. An On-the-Fly Surface-Hopping Program JADE for Nonadiabatic Molecular Dynamics of Polyatomic Systems: Implementation and Applications.

    Science.gov (United States)

    Du, Likai; Lan, Zhenggang

    2015-04-14

    Nonadiabatic dynamics simulations have rapidly become an indispensable tool for understanding ultrafast photochemical processes in complex systems. Here, we present our recently developed on-the-fly nonadiabatic dynamics package, JADE, which allows researchers to perform nonadiabatic excited-state dynamics simulations of polyatomic systems at an all-atomic level. The nonadiabatic dynamics is based on Tully's surface-hopping approach. Currently, several electronic structure methods (CIS, TDHF, TDDFT(RPA/TDA), and ADC(2)) are supported, especially TDDFT, aiming at performing nonadiabatic dynamics on medium- to large-sized molecules. The JADE package has been interfaced with several quantum chemistry codes, including Turbomole, Gaussian, and Gamess (US). To consider environmental effects, the Langevin dynamics was introduced as an easy-to-use scheme into the standard surface-hopping dynamics. The JADE package is mainly written in Fortran for greater numerical performance and Python for flexible interface construction, with the intent of providing open-source, easy-to-use, well-modularized, and intuitive software in the field of simulations of photochemical and photophysical processes. To illustrate the possible applications of the JADE package, we present a few applications of excited-state dynamics for various polyatomic systems, such as the methaniminium cation, fullerene (C20), p-dimethylaminobenzonitrile (DMABN) and its primary amino derivative aminobenzonitrile (ABN), and 10-hydroxybenzo[h]quinoline (10-HBQ).

  3. Case-based reasoning support for engineering design

    Science.gov (United States)

    Lees, Brian; Hamza, Meer; Irgens, Chris

    2000-10-01

    The potential application of case-based reasoning (CBR) in design support is illustrated through examples drawn from research at the University of Paisley, demonstrating the suitability of CBR for different aspects of design, different problem areas, and different design goals. A quality advisory system has been developed for the early stages of mechanical engineering design, the aim of which is to provide quality advice in a variant design situation. In the domain of software engineering CBR has been applied to advise on which metrics are appropriate fora assessing the quality of the software currently under design. The system integrates CBR with concepts from quality function deployment (QFD) and incorporates a case library holding past software quality histories. CBR has been applied in support of conceptual design: to capture detailed design histories by monitoring designer actions, and thereby support design reuse through the evaluation of designs, through the provision of query, browsing and replay facilities. The resulting system is aimed to support the design of safety critical systems, by assisting in the construction of safety arguments, and cooperative design.

  4. Increasing the efficiency and accuracy of time-resolved electronic spectra calculations with on-the-fly ab initio quantum dynamics methods

    Science.gov (United States)

    Vanicek, Jiri

    2014-03-01

    Rigorous quantum-mechanical calculations of coherent ultrafast electronic spectra remain difficult. I will present several approaches developed in our group that increase the efficiency and accuracy of such calculations: First, we justified the feasibility of evaluating time-resolved spectra of large systems by proving that the number of trajectories needed for convergence of the semiclassical dephasing representation/phase averaging is independent of dimensionality. Recently, we further accelerated this approximation with a cellular scheme employing inverse Weierstrass transform and optimal scaling of the cell size. The accuracy of potential energy surfaces was increased by combining the dephasing representation with accurate on-the-fly ab initio electronic structure calculations, including nonadiabatic and spin-orbit couplings. Finally, the inherent semiclassical approximation was removed in the exact quantum Gaussian dephasing representation, in which semiclassical trajectories are replaced by communicating frozen Gaussian basis functions evolving classically with an average Hamiltonian. Among other examples I will present an on-the-fly ab initio semiclassical dynamics calculation of the dispersed time-resolved stimulated emission spectrum of the 54-dimensional azulene. This research was supported by EPFL and by the Swiss National Science Foundation NCCR MUST (Molecular Ultrafast Science and Technology) and Grant No. 200021124936/1.

  5. 'Information on the fly': Challenges in professional communication in high technological nursing. A focus group study from a radiotherapy department in Sweden.

    Science.gov (United States)

    Widmark, Catarina; Tishelman, Carol; Gustafsson, Helena; Sharp, Lena

    2012-07-23

    Radiotherapy (RT) units are high-tech nursing environments. In Sweden, RT registered nurses (RNs) provide and manage RT in close collaboration with other professional groups, as well as providing nursing care for patients with cancer. Communication demands on these RNs are thus particularly complex. In this study, we aimed to better understand problems, strengths and change needs related to professional communication with and within the RT department, as a basis for developing a situation-specific intervention. Focus groups discussions (FGDs) were conducted with different professional (RNs, assistant nurses, physicians, engineers and physicists) and user stakeholders. Transcripts of the FGDs were inductively analyzed by a team of researchers, to generate clinically relevant and useful data. These findings give insight into RT safety climate and are presented under three major headings: Conceptualization of professional domains; Organization and leadership issues; and Communication forms, strategies and processes. The impact of existing hierarchies, including how they are conceptualized and acted out in practice, was noted throughout these data. Despite other differences, participating professionals agreed about communication problems related to RT, i.e. a lack of systems and processes for information transfer, unclear role differentiation, a sense of mutual disrespect, and ad hoc communication taking place 'on the fly'. While all professional groups recognized extensive communication problems, none acknowledged the potential negative effects on patient safety or care described in the FGD with patient representatives. While RNs often initially denied the existence of a hierarchy, they placed themselves on a hierarchy in their descriptions, describing their own role as passive, with a sense of powerlessness. Potential safety hazards described in the FGDs include not reporting medical errors and silently ignoring or actively opposing new guidelines and regulations

  6. An Agro-Climatological Early Warning Tool Based on the Google Earth Engine to Support Regional Food Security Analysis

    Science.gov (United States)

    Landsfeld, M. F.; Daudert, B.; Friedrichs, M.; Morton, C.; Hegewisch, K.; Husak, G. J.; Funk, C. C.; Peterson, P.; Huntington, J. L.; Abatzoglou, J. T.; Verdin, J. P.; Williams, E. L.

    2015-12-01

    The Famine Early Warning Systems Network (FEWS NET) focuses on food insecurity in developing nations and provides objective, evidence based analysis to help government decision-makers and relief agencies plan for and respond to humanitarian emergencies. The Google Earth Engine (GEE) is a platform provided by Google Inc. to support scientific research and analysis of environmental data in their cloud environment. The intent is to allow scientists and independent researchers to mine massive collections of environmental data and leverage Google's vast computational resources to detect changes and monitor the Earth's surface and climate. GEE hosts an enormous amount of satellite imagery and climate archives, one of which is the Climate Hazards Group Infrared Precipitation with Stations dataset (CHIRPS). The CHIRPS dataset is land based, quasi-global (latitude 50N-50S), 0.05 degree resolution, and has a relatively long term period of record (1981-present). CHIRPS is on a continuous monthly feed into the GEE as new data fields are generated each month. This precipitation dataset is a key input for FEWS NET monitoring and forecasting efforts. FEWS NET intends to leverage the GEE in order to provide analysts and scientists with flexible, interactive tools to aid in their monitoring and research efforts. These scientists often work in bandwidth limited regions, so lightweight Internet tools and services that bypass the need for downloading massive datasets to analyze them, are preferred for their work. The GEE provides just this type of service. We present a tool designed specifically for FEWS NET scientists to be utilized interactively for investigating and monitoring for agro-climatological issues. We are able to utilize the enormous GEE computing power to generate on-the-fly statistics to calculate precipitation anomalies, z-scores, percentiles and band ratios, and allow the user to interactively select custom areas for statistical time series comparisons and predictions.

  7. Chemical/Light-Powered Hybrid Micromotors with "On-the-Fly" Optical Brakes.

    Science.gov (United States)

    Chen, Chuanrui; Tang, Songsong; Teymourian, Hazhir; Karshalev, Emil; Zhang, Fangyu; Li, Jinxing; Mou, Fangzhi; Liang, Yuyan; Guan, Jianguo; Wang, Joseph

    2018-07-02

    Hybrid micromotors capable of both chemically powered propulsion and fuel-free light-driven actuation and offering built-in optical brakes for chemical propulsion are described. The new hybrid micromotors are designed by combining photocatalytic TiO 2 and catalytic Pt surfaces into a Janus microparticle. The chemical reactions on the different surfaces of the Janus particle hybrid micromotor can be tailored by using chemical or light stimuli that generate counteracting propulsion forces on the catalytic Pt and photocatalytic TiO 2 sides. Such modulation of the surface chemistry on a single micromotor leads to switchable propulsion modes and reversal of the direction of motion that reflect the tuning of the local ion concentration and hence the dominant propulsion force. An intermediate Au layer (under the Pt surface) plays an important role in determining the propulsion mechanism and operation of the hybrid motor. The built-in optical braking system allows "on-the-fly" control of the chemical propulsion through a photocatalytic reaction on the TiO 2 side to counterbalance the chemical propulsion force generated on the Pt side. The adaptive dual operation of these chemical/light hybrid micromotors, associated with such control of the surface chemistry, holds considerable promise for designing smart nanomachines that autonomously reconfigure their propulsion mode for various on-demand operations. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Photoionization dynamics of glycine adsorbed on a silicon cluster: ''On-the-fly'' simulations

    International Nuclear Information System (INIS)

    Shemesh, Dorit; Baer, Roi; Seideman, Tamar; Gerber, R. Benny

    2005-01-01

    Dynamics of glycine chemisorbed on the surface of a silicon cluster is studied for a process that involves single-photon ionization, followed by recombination with the electron after a selected time delay. The process is studied by ''on-the-fly'' molecular dynamics simulations, using the semiempirical parametric method number 3 (PM3) potential energy surface. The system is taken to be in the ground state prior to photoionization, and time delays from 5 to 50 fs before the recombination are considered. The time evolution is computed over 10 ps. The main findings are (1) the positive charge after ionization is initially mostly distributed on the silicon cluster. (2) After ionization the major structural changes are on the silicon cluster. These include Si-Si bond breaking and formation and hydrogen transfer between different silicon atoms. (3) The transient ionization event gives rise to dynamical behavior that depends sensitively on the ion state lifetime. Subsequent to 45 fs evolution in the charged state, the glycine molecule starts to rotate on the silicon cluster. Implications of the results to various processes that are induced by transient transition to a charged state are discussed. These include inelastic tunneling in molecular devices, photochemistry on conducting surfaces, and electron-molecule scattering

  9. Process support for Opticam: a concurrent engineering approach

    Science.gov (United States)

    Czajkowski, Walter C.; Tipps, Joe D., Jr.

    1992-12-01

    Although the principles of concurrent engineering and rapid product cycles are not new concepts in the industrial sector, the optics manufacturing industry has witnessed few technological advances since the 1940's. At present the optics industry maintains outdated stand-alone manufacturing equipment and systems that do little to foster integration or communications. 'Islands of Technology', spawned from the latest offerings of CNC controlled equipment, are generally stand alone systems incapable of supporting communication with other process equipment, not to mention the total business enterprise. This approach increases the cost in design and manufacture of optical systems while negatively impacting competitiveness in the global marketplace.

  10. Space Station Environmental Control/Life Support System engineering

    Science.gov (United States)

    Miller, C. W.; Heppner, D. B.

    1985-01-01

    The present paper is concerned with a systems engineering study which has provided an understanding of the overall Space Station ECLSS (Environmental Control and Life Support System). ECLSS/functional partitioning is considered along with function criticality, technology alternatives, a technology description, single thread systems, Space Station architectures, ECLSS distribution, mechanical schematics per space station, and Space Station ECLSS characteristics. Attention is given to trade studies and system synergism. The Space Station functional description had been defined by NASA. The ECLSS will utilize technologies which embody regenerative concepts to minimize the use of expendables.

  11. Computationally efficient simulation of unsteady aerodynamics using POD on the fly

    Energy Technology Data Exchange (ETDEWEB)

    Moreno-Ramos, Ruben [Gulfstream Aerospace Corporation, Savannah, GA 31408 (United States); Vega, José M; Varas, Fernando, E-mail: ruben.morenoramos@altran.com [E.T.S.I. Aeronáutica y del Espacio, Universidad Politécnica de Madrid, E-28040 Madrid (Spain)

    2016-12-15

    Modern industrial aircraft design requires a large amount of sufficiently accurate aerodynamic and aeroelastic simulations. Current computational fluid dynamics (CFD) solvers with aeroelastic capabilities, such as the NASA URANS unstructured solver FUN3D, require very large computational resources. Since a very large amount of simulation is necessary, the CFD cost is just unaffordable in an industrial production environment and must be significantly reduced. Thus, a more inexpensive, yet sufficiently precise solver is strongly needed. An opportunity to approach this goal could follow some recent results (Terragni and Vega 2014 SIAM J. Appl. Dyn. Syst. 13 330–65; Rapun et al 2015 Int. J. Numer. Meth. Eng. 104 844–68) on an adaptive reduced order model  that combines ‘on the fly’ a standard numerical solver (to compute some representative snapshots), proper orthogonal decomposition (POD) (to extract modes from the snapshots), Galerkin projection (onto the set of POD modes), and several additional ingredients such as projecting the equations using a limited amount of points and fairly generic mode libraries. When applied to the complex Ginzburg–Landau equation, the method produces acceleration factors (comparing with standard numerical solvers) of the order of 20 and 300 in one and two space dimensions, respectively. Unfortunately, the extension of the method to unsteady, compressible flows around deformable geometries requires new approaches to deal with deformable meshes, high-Reynolds numbers, and compressibility. A first step in this direction is presented considering the unsteady compressible, two-dimensional flow around an oscillating airfoil using a CFD solver in a rigidly moving mesh. POD on the Fly gives results whose accuracy is comparable to that of the CFD solver used to compute the snapshots. (paper)

  12. Developing engineering capabilities as a support to a nuclear program

    International Nuclear Information System (INIS)

    Rodriguez, A.G.

    1986-04-01

    The performance of a nuclear program needs a quite substantial and diversified volume of technological resources. Its integrated management is one of the basic aspects to be settled. In this regard, the creation of strong engineering organizations with the ability to develop management of the project technical activities as a whole has had success in various countries. These organizations should be provided with suitable means to rapidly assimilate the technology and should serve as a channel and support to local industry in general. The development of a nuclear program also requires the collaboration of other institutions, such as universities and research and development centers. In this sense, engineer and technician training necessities are important both in number and technological qualification, as is the availability of capacities in such different areas as simulation and advanced calculation, geology and soil mechanics, materials, fabrication processes, test laboratories, etc. The volume of technological activities to be developed in relation to a stable, although not necessarily large, nuclear program justifies in itself the assigning of important resources to all the above mentioned activities. However, it should be noted that it has been proved that the nuclear industry is completely pervious as regards other fields of activity. In fact, the more stringent quality requirements are quickly transmitted to other industrial processes, and the engineers trained in this area undergo a far from contemptible turnover towards non-nuclear activities. The basic research area in the nuclear field is not in itself a requirement that has to be in parallel with the development of a nuclear program. However, on medium and long-term bases, it may be interesting for a well balanced commercial program that research activities be established realistically and sensibly, even though short-term practical applications are not necessarily derived from this

  13. Software Packages to Support Electrical Engineering Virtual Lab

    Directory of Open Access Journals (Sweden)

    Manuel Travassos Valdez

    2012-03-01

    Full Text Available The use of Virtual Reality Systems (VRS, as a learning aid, encourages the creation of tools that allow users/students to simulate educational environments on a computer. This article presents a way of building a VRS system with Software Packages to support Electrical Engineering Virtual Laboratories to be used in a near future in the teaching of the curriculum unit of Circuit Theory. The steps required for the construction of a project are presented in this paper. The simulation is still under construction and intends to use a three-dimensional virtual environment laboratory electric measurement, which will allow users/students to experiment and test the modeled equipment. Therefore, there are still no links available for further examination. The result may demonstrate the future potential of applications of Virtual Reality Systems as an efficient and cost-effective learning system.

  14. On-the-fly Locata/inertial navigation system integration for precise maritime application

    Science.gov (United States)

    Jiang, Wei; Li, Yong; Rizos, Chris

    2013-10-01

    The application of Global Navigation Satellite System (GNSS) technology has meant that marine navigators have greater access to a more consistent and accurate positioning capability than ever before. However, GNSS may not be able to meet all emerging navigation performance requirements for maritime applications with respect to service robustness, accuracy, integrity and availability. In particular, applications in port areas (for example automated docking) and in constricted waterways, have very stringent performance requirements. Even when an integrated inertial navigation system (INS)/GNSS device is used there may still be performance gaps. GNSS signals are easily blocked or interfered with, and sometimes the satellite geometry may not be good enough for high accuracy and high reliability applications. Furthermore, the INS accuracy degrades rapidly during GNSS outages. This paper investigates the use of a portable ground-based positioning system, known as ‘Locata’, which was integrated with an INS, to provide accurate navigation in a marine environment without reliance on GNSS signals. An ‘on-the-fly’ Locata resolution algorithm that takes advantage of geometry change via an extended Kalman filter is proposed in this paper. Single-differenced Locata carrier phase measurements are utilized to achieve accurate and reliable solutions. A ‘loosely coupled’ decentralized Locata/INS integration architecture based on the Kalman filter is used for data processing. In order to evaluate the system performance, a field trial was conducted on Sydney Harbour. A Locata network consisting of eight Locata transmitters was set up near the Sydney Harbour Bridge. The experiment demonstrated that the Locata on-the-fly (OTF) algorithm is effective and can improve the system accuracy in comparison with the conventional ‘known point initialization’ (KPI) method. After the OTF and KPI comparison, the OTF Locata/INS integration is then assessed further and its performance

  15. On-the-fly Locata/inertial navigation system integration for precise maritime application

    International Nuclear Information System (INIS)

    Jiang, Wei; Li, Yong; Rizos, Chris

    2013-01-01

    The application of Global Navigation Satellite System (GNSS) technology has meant that marine navigators have greater access to a more consistent and accurate positioning capability than ever before. However, GNSS may not be able to meet all emerging navigation performance requirements for maritime applications with respect to service robustness, accuracy, integrity and availability. In particular, applications in port areas (for example automated docking) and in constricted waterways, have very stringent performance requirements. Even when an integrated inertial navigation system (INS)/GNSS device is used there may still be performance gaps. GNSS signals are easily blocked or interfered with, and sometimes the satellite geometry may not be good enough for high accuracy and high reliability applications. Furthermore, the INS accuracy degrades rapidly during GNSS outages. This paper investigates the use of a portable ground-based positioning system, known as ‘Locata’, which was integrated with an INS, to provide accurate navigation in a marine environment without reliance on GNSS signals. An ‘on-the-fly’ Locata resolution algorithm that takes advantage of geometry change via an extended Kalman filter is proposed in this paper. Single-differenced Locata carrier phase measurements are utilized to achieve accurate and reliable solutions. A ‘loosely coupled’ decentralized Locata/INS integration architecture based on the Kalman filter is used for data processing. In order to evaluate the system performance, a field trial was conducted on Sydney Harbour. A Locata network consisting of eight Locata transmitters was set up near the Sydney Harbour Bridge. The experiment demonstrated that the Locata on-the-fly (OTF) algorithm is effective and can improve the system accuracy in comparison with the conventional ‘known point initialization’ (KPI) method. After the OTF and KPI comparison, the OTF Locata/INS integration is then assessed further and its performance

  16. Information System Engineering Supporting Observation, Orientation, Decision, and Compliant Action

    Science.gov (United States)

    Georgakopoulos, Dimitrios

    The majority of today's software systems and organizational/business structures have been built on the foundation of solving problems via long-term data collection, analysis, and solution design. This traditional approach of solving problems and building corresponding software systems and business processes, falls short in providing the necessary solutions needed to deal with many problems that require agility as the main ingredient of their solution. For example, such agility is needed in responding to an emergency, in military command control, physical security, price-based competition in business, investing in the stock market, video gaming, network monitoring and self-healing, diagnosis in emergency health care, and many other areas that are too numerous to list here. The concept of Observe, Orient, Decide, and Act (OODA) loops is a guiding principal that captures the fundamental issues and approach for engineering information systems that deal with many of these problem areas. However, there are currently few software systems that are capable of supporting OODA. In this talk, we provide a tour of the research issues and state of the art solutions for supporting OODA. In addition, we provide specific examples of OODA solutions we have developed for the video surveillance and emergency response domains.

  17. Development of decommissioning engineering support system for fugen. Development of support system during actual dismantlement works

    International Nuclear Information System (INIS)

    Masanori Izumi; Yukihiro Iguchi; Yoshiki Kannehira

    2005-01-01

    The Advanced Thermal Reactor, Fugen Nuclear Power Station was permanently shut down in March 2003, and is now preparing for decommissioning. We have been developing Decommissioning Engineering Support System (DEXUS) aimed at planning optimal dismantlement process and carrying out dismantlement work safely and precisely. DEXUS consists of 'decommissioning planning support system' and 'dismantling support system'. The dismantling support system is developed aiming at using during actual dismantling work. It consists of three subsystems such as 'Worksite Visualization System', 'Dismantling Data Collection System' and 'Generated Waste Management System'. 'Worksite Visualization System' is a support system designed to provide the necessary information to workers during actual dismantlement works. And this system adopts AR (Augmented Reality) technology, overlapping calculation information into real world. 'Dismantling Data Collection System' is to collect necessary data for improving accuracy of decommissioning planning by evaluating work content and worker equipage, work time for dismantlement works. 'Generated Waste Management system' is a system recording necessary information by attaching the barcode to dismantled wastes or the containers. We can get the information of generated waste by recording generation place, generated time, treatment method and the contents. These subsystems enable to carry out reasonable and safe decommissioning of Fugen. In addition, we expect that those systems will be used for decommissioning of other nuclear facilities in the future. (authors)

  18. Supporting Usability Engineering in Small Software Development Organizations

    DEFF Research Database (Denmark)

    Bornoe, Nis; Stage, Jan

    2013-01-01

    Despite an interest and use of different usability engineering methods small software development organizations find it challenging to implement usability engineering into the software development process. We present the results from a study about usability engineering in practice. Through a series...... of semistructured interviews we want to get an understanding of how usability is implemented into the organizations and how it’s practiced in reality. We found that the developers found it problematic to combine agile software development methods with classic usability engineering methods. A lack of solid usability...... engineering expertise and not least experience seems to be a main obstacle for a successful implementation of usability engineering into current software development practices. They are requesting methods and procedures that fit better with their current practices and strategies to implement usability...

  19. Engineering support for plant life management: the IAEA contribution

    International Nuclear Information System (INIS)

    Kang, K.; Hezoucky, F.; Clark, R. C.; )

    2007-01-01

    For the past couple of decades there has been a change of emphasis in the world nuclear power from that of building new Nuclear Power Plants (NPP) to that of taking measures to optimize the life cycle of operational plants. National approaches in many countries showed an increase of interest in Plant Life Management (PLiM), both in terms of plant service life assurance and in optimizing the service or operational life of NPP. The safety considerations of a NPP are paramount and those requirements have to be met to obtain and to extend/renew the operating license. To achieve the goal of the long term safe, economic and reliable operation of the plant, PLiM programme is essential. Some countries already have advanced PLiM programmes while others still have none. The PLiM objective is to identify all that factors and requirements for the overall plant life cycle. The optimization of these requirements would allow for the minimum period of the investment return and maximum of the revenue from the sell of the produced electricity. Recognizing the importance of this issue and in response to the requests of the Member States the IAEA Division of Nuclear Power implements the Sub-programme on 'Engineering and Management Support for Competitive Nuclear Power'. Three projects within this sub-programme deal with different aspects of the NPP life cycle management with the aim to increase the capabilities of interested Member States in implementing and maintenance of the competitive and sustainable nuclear power. Although all three projects contain certain issues of PLiM, there is one specific project on guidance on engineering and management practices for optimization of NPP service life. This particular project deals with different specific issues of PLiM including aspects of ageing phenomena and their monitoring, issues of control and instrumentation, maintenance and operation issues, economic evaluation of PLiM including guidance on its earlier shut down and decommissioning

  20. Support for Different Roles in Software Engineering Master's Thesis Projects

    Science.gov (United States)

    Host, M.; Feldt, R.; Luders, F.

    2010-01-01

    Like many engineering programs in Europe, the final part of most Swedish software engineering programs is a longer project in which the students write a Master's thesis. These projects are often conducted in cooperation between a university and industry, and the students often have two supervisors, one at the university and one in industry. In…

  1. Formal Abstraction in Engineering Education--Challenges and Technology Support

    Science.gov (United States)

    Neuper, Walther A.

    2017-01-01

    This is a position paper in the field of Engineering Education, which is at the very beginning in Europe. It relates challenges in the new field to the emerging technology of (Computer) Theorem Proving (TP). Experience shows, that "teaching" abstract models, for instance the wave equation in mechanical engineering and in electrical…

  2. A New On-the-Fly Sampling Method for Incoherent Inelastic Thermal Neutron Scattering Data in MCNP6

    Energy Technology Data Exchange (ETDEWEB)

    Pavlou, Andrew Theodore [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Brown, Forrest B. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ji, Wei [Rensselaer Polytechnic Inst., Troy, NY (United States)

    2014-09-02

    At thermal energies, the scattering of neutrons in a system is complicated by the comparable velocities of the neutron and target, resulting in competing upscattering and downscattering events. The neutron wavelength is also similar in size to the target's interatomic spacing making the scattering process a quantum mechanical problem. Because of the complicated nature of scattering at low energies, the thermal data files in ACE format used in continuous-energy Monte Carlo codes are quite large { on the order of megabytes for a single temperature and material. In this paper, a new storage and sampling method is introduced that is orders of magnitude less in size and is used to sample scattering parameters at any temperature on-the-fly. In addition to the reduction in storage, the need to pre-generate thermal scattering data tables at fine temperatures has been eliminated. This is advantageous for multiphysics simulations which may involve temperatures not known in advance. A new module was written for MCNP6 that bypasses the current S(α,β) table lookup in favor of the new format. The new on-the-fly sampling method was tested for graphite for two benchmark problems at ten temperatures: 1) an eigenvalue test with a fuel compact of uranium oxycarbide fuel homogenized into a graphite matrix, 2) a surface current test with a \\broomstick" problem with a monoenergetic point source. The largest eigenvalue difference was 152pcm for T= 1200K. For the temperatures and incident energies chosen for the broomstick problem, the secondary neutron spectrum showed good agreement with the traditional S(α,β) sampling method. These preliminary results show that sampling thermal scattering data on-the-fly is a viable option to eliminate both the storage burden of keeping thermal data at discrete temperatures and the need to know temperatures before simulation runtime.

  3. On-the-fly depth profiling during ablation with ultrashort laser pulses: A tool for accurate micromachining and laser surgery

    International Nuclear Information System (INIS)

    Lausten, Rune; Balling, Peter

    2001-01-01

    A method for accurate depth profiling of a region subjected to ablation with ultrashort laser pulses is demonstrated. Time-gated imaging of the backscattered radiation from the ablation region is performed in a geometry, which allows the depth along a chosen axis on the sample to be determined with a single measurement. The profiling system has a spatial resolution of a few micrometers and applications are promoted by the fact that the measurement is performed with the same pulse that undertakes ablation. This also indicates that the method is inherently suited for in situ on-the-fly measurements. Copyright 2001 American Institute of Physics

  4. Use of magnetic compression to support turbine engine rotors

    Science.gov (United States)

    Pomfret, Chris J.

    1994-01-01

    Ever since the advent of gas turbine engines, their rotating disks have been designed with sufficient size and weight to withstand the centrifugal forces generated when the engine is operating. Unfortunately, this requirement has always been a life and performance limiting feature of gas turbine engines and, as manufacturers strive to meet operator demands for more performance without increasing weight, the need for innovative technology has become more important. This has prompted engineers to consider a fundamental and radical breakaway from the traditional design of turbine and compressor disks which have been in use since the first jet engine was flown 50 years ago. Magnetic compression aims to counteract, by direct opposition rather than restraint, the centrifugal forces generated within the engine. A magnetic coupling is created between a rotating disk and a stationary superconducting coil to create a massive inwardly-directed magnetic force. With the centrifugal forces opposed by an equal and opposite magnetic force, the large heavy disks could be dispensed with and replaced with a torque tube to hold the blades. The proof of this concept has been demonstrated and the thermal management of such a system studied in detail; this aspect, especially in the hot end of a gas turbine engine, remains a stiff but not impossible challenge. The potential payoffs in both military and commercial aviation and in the power generation industry are sufficient to warrant further serious studies for its application and optimization.

  5. A Modular Artificial Intelligence Inference Engine System (MAIS) for support of on orbit experiments

    Science.gov (United States)

    Hancock, Thomas M., III

    1994-01-01

    This paper describes a Modular Artificial Intelligence Inference Engine System (MAIS) support tool that would provide health and status monitoring, cognitive replanning, analysis and support of on-orbit Space Station, Spacelab experiments and systems.

  6. Space-Based Infrared System-Supportability Engineering and Acquisition Reform in an Existing Acquisition Environment

    National Research Council Canada - National Science Library

    Fickes, Richard

    1999-01-01

    .... SBIRS is being developed in three increments. This article discusses supportability requirements definition and the implementation of supportability engineering in SBIRS evolution from an Integrated Product Team (IPT) aspect...

  7. A Decision Support Framework for Evaluation of Engineered Nanomaterials

    Science.gov (United States)

    Engineered nanomaterials (ENM) are currently being developed and applied at rates that far exceed our ability to evaluate their potential for environmental or human health risks. The gap between material development and capacity for assessment grows wider every day. Transforma...

  8. Support of Study on Engineering Technology from Physics and Mathematics

    OpenAIRE

    Mynbaev, Djafar K.; Cabo, Candido; Kezerashvili, Roman Ya.; Liou-Mark, Janet

    2008-01-01

    An approach that provides students with an ability to transfer learning in physics and mathematics to the engineering-technology courses through e-teaching and e-learning process is proposed. E-modules of courses in mathematics, physics, computer systems technology, and electrical and telecommunications engineering technology have been developed. These modules being used in the Blackboard and Web-based communications systems create a virtual interdisciplinary learning community, which helps t...

  9. Statistics and Probability Theory In Pursuit of Engineering Decision Support

    CERN Document Server

    Faber, Michael Havbro

    2012-01-01

    This book provides the reader with the basic skills and tools of statistics and probability in the context of engineering modeling and analysis. The emphasis is on the application and the reasoning behind the application of these skills and tools for the purpose of enhancing  decision making in engineering. The purpose of the book is to ensure that the reader will acquire the required theoretical basis and technical skills such as to feel comfortable with the theory of basic statistics and probability. Moreover, in this book, as opposed to many standard books on the same subject, the perspective is to focus on the use of the theory for the purpose of engineering model building and decision making.  This work is suitable for readers with little or no prior knowledge on the subject of statistics and probability.

  10. Office of Research Support | College of Engineering & Applied Science

    Science.gov (United States)

    Professor and Associate Dean for Research College of Engineering and Applied Sciences Director, Center for Academics Admission Student Life Research Schools & Colleges Libraries Athletics Centers & ; Applied Science Powerful Ideas. Proven Results. Search for: Go This site All UWM Search Site Menu Skip to

  11. On Engineering Support for Business Process Modelling and Redesign

    NARCIS (Netherlands)

    Doumeingts, G.; Franken, H.M.; de Weger, M.K.; Browne, J.; Quartel, Dick; Ferreira Pires, Luis

    1997-01-01

    Currently, there is an enormous (research) interest in business process redesign (BPR). Several management-oriented approaches have been proposed showing how to make BPR work. However, detailed descriptions of empirical experience are few. Consistent engineering methodologies to aid and guide a

  12. Engine Management : A Decision Support Tool for Strategic Engine Maintenance Planning

    NARCIS (Netherlands)

    Mayordomo, A.F.; Ghobbar, A.A.; Ghijs, S.S.A.; Cator, E.

    2010-01-01

    This paper presents a model that helps engine management make cost saving decisions. The model is developed around airline-influenced factors that have an impact on engine Maintenance Repair & Overhaul (MRO): Operations, maintenance philosophy, contract type, and fleet age. Within the model a

  13. Preliminary performance evaluation of on-the-fly doppler broadening capability for Monte Carlo simulation in MCS

    International Nuclear Information System (INIS)

    Khassenov, A.; Choi, S.; Lee, H.; Zhang, P.; Zheng, Y.; Lee, D.

    2015-01-01

    This paper examines multipole representation of the cross section and its further Doppler broadening at the resolved resonance region. At the first step, a conversion is performed from nuclear data file resonance parameters to multipoles, which are corresponding poles and residues. The application of multipole representation allows generating the cross section at the target temperature, without pre-generation of 0K cross section libraries. In order to reduce the computational time for cross section generation, window energy concept was implemented and tested. On-the-fly Doppler broadening module based on multipole and windowed multipole representations were implemented into Monte Carlo code, and a pin cell problem was simulated. Simulation time and multiplication factors for different cases were compared with original Monte Carlo simulation results. (author)

  14. Engineering Technical Support Center Annual Report Fiscal Year 2016

    Science.gov (United States)

    This report highlights significant projects that the ETSC supported in fiscal year 2016. These projects have addressed an array of environmental scenarios, including, but not limited to remote mining contamination, expansive landfill waste, cumulative impacts from multiple contam...

  15. Adding Robustness to Support Vector Machines Against Adversarial Reverse Engineering

    KAUST Repository

    Alabdulmohsin, Ibrahim

    2014-01-01

    Many classification algorithms have been successfully deployed in security-sensitive applications including spam filters and intrusion detection systems. Under such adversarial environments, adversaries can generate exploratory attacks against the defender such as evasion and reverse engineering. In this paper, we discuss why reverse engineering attacks can be carried out quite efficiently against fixed classifiers, and investigate the use of randomization as a suitable strategy for mitigating their risk. In particular, we derive a semidefinite programming (SDP) formulation for learning a distribution of classifiers subject to the constraint that any single classifier picked at random from such distribution provides reliable predictions with a high probability. We analyze the tradeoff between variance of the distribution and its predictive accuracy, and establish that one can almost always incorporate randomization with large variance without incurring a loss in accuracy. In other words, the conventional approach of using a fixed classifier in adversarial environments is generally Pareto suboptimal. Finally, we validate such conclusions on both synthetic and real-world classification problems. Copyright 2014 ACM.

  16. An Engineering Educator's Decision Support Tool for Improving Innovation in Student Design Projects

    Science.gov (United States)

    Ozaltin, Nur Ozge; Besterfield-Sacre, Mary; Clark, Renee M.

    2015-01-01

    Learning how to design innovatively is a critical process skill for undergraduate engineers in the 21st century. To this end, our paper discusses the development and validation of a Bayesian network decision support tool that can be used by engineering educators to make recommendations that positively impact the innovativeness of product designs.…

  17. Engineering Task Plan for Water Supply for Spray Washers on the Support Trucks

    International Nuclear Information System (INIS)

    BOGER, R.M.

    2000-01-01

    This Engineering Task Plan (ETP) defines the task and deliverables associated with the design, fabrication and testing of an improved spray wash system for the Rotary Mode Core Sampling (RMCS) System Support Trucks

  18. Civil engineering support for the traffic monitoring program : final report, January 2010.

    Science.gov (United States)

    2010-01-01

    This project was aimed at providing various civil engineering support services for the telemetered traffic monitoring sites operated by the Statistics Office of the Florida Department of Transportation. This was a companion project to the one that pr...

  19. Technical engineering services in support of the Nike-Tomahawk sounding rocket vehicle system

    Science.gov (United States)

    1972-01-01

    Task assignments in support of the Nike-Tomahawk vehicles, which were completed from May, 1970 through November 1972 are reported. The services reported include: analytical, design and drafting, fabrication and modification, and field engineering.

  20. Cognitive System Engineering Approach to Design of Work Support Systems

    DEFF Research Database (Denmark)

    Rasmussen, Jens

    1995-01-01

    The problem of designing work support systems for flexible, dynamic work environments is discussed and a framework for analysis of work in terms of behavior shaping constraints is described. The application of 'ecological interfaces' presenting to the user a map of the relational structure...... of the work space is advocated from the thesis that a map is a better guidance of discretionary tasks than is a route instruction. For the same reason, support of system design is proposed in terms of maps of the design territory, rather than in terms of guidelines....

  1. ESTIMATION OF EXTERNAL FACTORS INFLUENCE ON THE ORGANIZATIONAL AND RESOURCE SUPPORT OF ENGINEERING

    Directory of Open Access Journals (Sweden)

    Yu. V. Gusak

    2013-09-01

    Full Text Available Purpose. The engineering industry is characterized by deep specialization and high co-operation, which suggests a high degree of interaction with other industries and the economy, highly sensitive to external factors. Effective regulation of the engineering industry’s organizational-resource support will ensure coherence of all the subsystems of the market economy, the competitive environment, a full course of the investment process and the success of the industry. Therefore there is a need for detailed estimation and analysis of the external factors’ influence on the formation and implementation indexes of the engineering industry’s organizational-resource support. Methodology. To establish the close connection between the set of external factors of formation and implementation indexes of the engineering industry organizational-resource support the correlation analysis was used, to calculate the amount of the formation and implementation indexes of the engineering industry organizational-resource support’s change under the influence of the external factors with malleability coefficient were applied. Findings. The external influence factors on the engineering industry organizational-resource support by the source of origin: industrial, economical, political, informational, and social were separated and grouped. The classification of the external factors influence on the engineering industry organizational-resource support, depending on their influence’s direction on the formation and implementation indexes of the engineering industry’s organizational-resource support was made. The connection closeness and the amount of the formation and implementation indexes of the engineering industry organizational-resource support change (the machinery index of and the sales volume machinery index under the influence of the external factors with malleability coefficient were determined. Originality. The estimation of the external factors

  2. Grammar Engineering Support for Precedence Rule Recovery and Compatibility Checking

    NARCIS (Netherlands)

    Bouwers, E.; Bravenboer, M.; Visser, E.

    2007-01-01

    A wide range of parser generators are used to generate parsers for programming languages. The grammar formalisms that come with parser generators provide different approaches for defining operator precedence. Some generators (e.g. YACC) support precedence declarations, others require the grammar to

  3. (Technical and engineering support for the Office of Industrial Programs)

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-01

    As of April 19, 1991, technical, operational and analytic support and assistance to the offices and divisions of the Office of Renewable Energy, under contract DE-AC01-86CE30844 was completed. The overall work effort, initiated February 20, 1986, was characterized by timely, comprehensive, high quality, professional responsiveness to a broad range of renewable energy program operational support requirements. These are no instances of failure to respond, nor unacceptable response, during the five-year period. The technology program areas covered are Solar Buildings Technology, Wind Energy Technology, Photovoltaic Energy Technology, Geothermal Energy Technology, Biofuels and Municipal Waste Technology, Solar Thermal Technology, Hydropower Energy Technology, Ocean Energy Technology, and Electric Energy Systems and Energy Storage. The analytical and managerial support provided to the office and staff of the Deputy Assistant Secretary for Renewable Energy enabled a comprehensive evaluation of program and policy alternatives, and the selection and execution of appropriate courses of action from amongst those alternatives. Largely through these means the Office has been able to maintain continuity and a meaningful program thrust through the vacillations of policies and budgets that it has experienced over that it has experienced over the past five years. Appended are summaries of support activities within each of the individual technology program areas, as well as a complete listing of all project deliverables and due-dates for each submittal under the contract.

  4. [Technical and engineering support for the Office of Industrial Programs

    International Nuclear Information System (INIS)

    1991-01-01

    As of April 19, 1991, technical, operational and analytic support and assistance to the offices and divisions of the Office of Renewable Energy, under contract DE-AC01-86CE30844 was completed. The overall work effort, initiated February 20, 1986, was characterized by timely, comprehensive, high quality, professional responsiveness to a broad range of renewable energy program operational support requirements. These are no instances of failure to respond, nor unacceptable response, during the five-year period. The technology program areas covered are Solar Buildings Technology, Wind Energy Technology, Photovoltaic Energy Technology, Geothermal Energy Technology, Biofuels and Municipal Waste Technology, Solar Thermal Technology, Hydropower Energy Technology, Ocean Energy Technology, and Electric Energy Systems and Energy Storage. The analytical and managerial support provided to the office and staff of the Deputy Assistant Secretary for Renewable Energy enabled a comprehensive evaluation of program and policy alternatives, and the selection and execution of appropriate courses of action from amongst those alternatives. Largely through these means the Office has been able to maintain continuity and a meaningful program thrust through the vacillations of policies and budgets that it has experienced over that it has experienced over the past five years. Appended are summaries of support activities within each of the individual technology program areas, as well as a complete listing of all project deliverables and due-dates for each submittal under the contract

  5. ECOS: a configurable, multi-terabyte database supporting engineering and technical computing at Sizewell B

    International Nuclear Information System (INIS)

    Binns, F.; Fish, A.

    1992-01-01

    One of the three main classes of computing support systems is concerned with the technical and engineering aspects of Sizewell-B power station. These aspects are primarily concerned with engineering means to optimise plant use to maximise power output by increasing availability and efficiency. At Sizewell-B the Engineering Computer system (ECOS) will provide the necessary support facilities, and is described. ECOS is being used by the station commissioning team and for monitoring the state of some plant already in service. (Author)

  6. Engineering performance indicators in support of corporate goals and objectives

    International Nuclear Information System (INIS)

    Prawlocki, F.C.; Holland, M.B.

    1992-01-01

    In the late 1980s, a new factor was introduced into the equation of rate making: competition. Prior to this time, most utilities only had to prove to the state public service commission (PSC) that a rate increase was justified. Even this had become more difficult in recent years as PSCs implemented prudency audits as a means of determining the efficiency of utility management. Recently, however, the need for performance improvement has been initiated internally by utility management because of the advent of competition in the utility environment and state PSC inquiries. In 1991, TVA began to realign its traditional program of performance indicators to agree with industry standards and provide more extensive indicators of positive and negative trends in performance. The INPO Guideline 88-016, Guidelines for the Conduct of Design Engineering, was used as the basis for most indicators. In addition, indicators were added to highlight specific corporate objectives, problems, or regulatory commitments. The indicators are being initiated in three phases as efficient sources of performance data are identified. Once the current baseline was established, a review was made of the best utilities in the country based on the US Nuclear Regulatory Commission's systematic assessment of licensee's performance and INPO performance indicators to establish performance goals. As total quality management and cycle time reduction programs are implemented, all of the organization's annual goals and objectives are expected to more closely reflect the best of the industry

  7. A Decision Support Framework for Evaluation of Engineered ...

    Science.gov (United States)

    Engineered nanomaterials (ENM) are currently being developed and applied at rates that far exceed our ability to evaluate their potential for environmental or human health risks. The gap between material development and capacity for assessment grows wider every day. Transformative approaches are required that enhance our ability to forecast potential exposure and adverse health risks based on limited information such as the physical and chemical parameters of ENM, their proposed uses, and functional assays reflective of key ENM - environmental interactions. We are developing a framework that encompasses the potential for release of nanomaterials across a product life cycle, environmental transport, transformations and fate, exposure to sensitive species, including humans, and the potential for causing adverse effects. Each component of the framework is conceive of as a sequential segmented model depicting the movement, transformations and actions of ENM through environmental or biological compartments, and along which targeted functional assays can be developed that are indicative of projected rates of ENM movement or action. The eventual goal is to allow simple predictive models to be built that incorporate the data from key functional assays and thereby allow rapid screening of the projected margin of exposure for proposed applications of ENM enabled products. In this way, cases where a substantially safe margin of exposure is forecast can be reduced in

  8. Towards artificial intelligence based diesel engine performance control under varying operating conditions using support vector regression

    Directory of Open Access Journals (Sweden)

    Naradasu Kumar Ravi

    2013-01-01

    Full Text Available Diesel engine designers are constantly on the look-out for performance enhancement through efficient control of operating parameters. In this paper, the concept of an intelligent engine control system is proposed that seeks to ensure optimized performance under varying operating conditions. The concept is based on arriving at the optimum engine operating parameters to ensure the desired output in terms of efficiency. In addition, a Support Vector Machines based prediction model has been developed to predict the engine performance under varying operating conditions. Experiments were carried out at varying loads, compression ratios and amounts of exhaust gas recirculation using a variable compression ratio diesel engine for data acquisition. It was observed that the SVM model was able to predict the engine performance accurately.

  9. System Engineering and Integration of Controls for Advanced Life Support

    Science.gov (United States)

    Overland, David; Hoo, Karlene; Ciskowski, Marvin

    2006-01-01

    The Advanced Integration Matrix (AIM) project at the Johnson Space Center (JSC) was chartered to study and solve systems-level integration issues for exploration missions. One of the first issues identified was an inability to conduct trade studies on control system architectures due to the absence of mature evaluation criteria. Such architectures are necessary to enable integration of regenerative life support systems. A team was formed to address issues concerning software and hardware architectures and system controls.. The team has investigated what is required to integrate controls for the types of non-linear dynamic systems encountered in advanced life support. To this end, a water processing bioreactor testbed is being developed which will enable prototyping and testing of integration strategies and technologies. Although systems such as the water bioreactors exhibit the complexities of interactions between control schemes most vividly, it is apparent that this behavior and its attendant risks will manifest itself among any set of interdependent autonomous control systems. A methodology for developing integration requirements for interdependent and autonomous systems is a goal of this team and this testbed. This paper is a high-level summary of the current status of the investigation, the issues encountered, some tentative conclusions, and the direction expected for further research.

  10. Rabs on the fly

    DEFF Research Database (Denmark)

    Caviglia, Sara; Flores-Benitez, David; Lattner, Johanna

    2017-01-01

    The organisation of intracellular transport processes is adapted specifically to different cell types, developmental stages, and physiological requirements. Some protein traffic routes are universal to all cells and constitutively active, while other routes are cell-type specific, transient...

  11. Performance support system in higher engineering education - introduction and empirical validation

    NARCIS (Netherlands)

    Stoyanov, S.; Stoyanov, Slavi; Kommers, Petrus A.M.; Bastiaens, T.J.; Martinez Mediano, Catalina

    2008-01-01

    The paper defines and empirically validates the concept of performance support system in higher engineering education. The validation of the concept is based upon two studies: a pilot and an experiment, on the effect of performance support system on achievements and attitudes of students. The

  12. On-the-fly green generation and dispersion of AgI nanoparticles for cloud seeding nuclei

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Xiuli; Zhou, Wenbo; Wang, Xizheng; Wu, Tao; Delisio, Jeffery B.; Zachariah, Michael R., E-mail: mrz@umd.edu [University of Maryland, Department of Chemical and Biomolecular Engineering (United States)

    2016-07-15

    This study reports on an on-the-fly green synthesis/dispersion of silver iodide (AgI) nanoparticles from the combustion of AgIO{sub 3}/carbon black (CB)/nitrocellulose (NC) composites, which could be used as a candidate for a cloud-seeding pyrotechnic. Films were formed by direct electrospray deposition of a mixture of synthesized silver iodate with CB and NC. The decomposition pathways of AgIO{sub 3}/CB and AgIO{sub 3}/CB/NC were evaluated by temperature jump time of flight mass spectrometry (T-jump TOFMS) and XRD, showing that AgI particles and CO{sub 2} are released from the reaction between AgIO{sub 3} and CB without other toxic residuals. The flame propagation velocity of AgIO{sub 3}/CB/NC films increases with the increasing of particle mass loading of AgIO{sub 3} and CB and peaks at 40 wt%, which is much higher than that of an AgI/AP/NC film. The mean diameter of the resultant AgI nanoparticles is from 51 to 97 nm. The mass loading of AgIO{sub 3} and CB was found to play a major role in size control of the AgI nanoparticles.

  13. WikiD : A WikiEngine Supporting Structured Data

    CERN Multimedia

    CERN. Geneva; Young, Jeffrey

    2005-01-01

    Ward Cunningham describes a wiki as "the simplest online database that could possibly work". The cost of this simplicity is that wikis are generally limited to a single collection containing a single kind of record (viz. WikiMarkupLanguage records). WikiD extends the Wiki model to support multiple collections containing arbitrary schemas of XML records with minimal additional complexity. WikiD is essentially a lightweight framework combining: * Open-source implementations of various loosely-coupled open-standard protocols (e.g. OpenURL, SRW/U, SRW Update, OAI-PMH, RSS) * An open-source version-controlled database. * A set of bootstrap collections. * XSL Stylesheets to render collection-level open-standard protocol responses into HTML for human consumption. Automated processes can ignore the stylesheet reference and use the open-standard protocol responses directly. Possible applications for WikiD include collaborative maintenance of registries, thesauri, taxonomies, reviews, and documentation. In addition to ...

  14. Less Words, More Action: Using On-the-Fly Videos and Screenshots in Your Library's IM/Chat and Email Reference Transactions

    Science.gov (United States)

    Sekyere, Kwabena

    2010-01-01

    Email and chat/IM reference services have become a convenient and easily accessible option for the online community and libraries, particularly with increasing amounts of library resources now available electronically. This article gives an overview of Jing, which can be used to produce videos and screenshots on-the-fly, and demonstrates how to…

  15. Practical support for Lean Six Sigma software process definition using IEEE software engineering standards

    CERN Document Server

    Land, Susan K; Walz, John W

    2012-01-01

    Practical Support for Lean Six Sigma Software Process Definition: Using IEEE Software Engineering Standards addresses the task of meeting the specific documentation requirements in support of Lean Six Sigma. This book provides a set of templates supporting the documentation required for basic software project control and management and covers the integration of these templates for their entire product development life cycle. Find detailed documentation guidance in the form of organizational policy descriptions, integrated set of deployable document templates, artifacts required in suppo

  16. Status of the Tidal Regenerator Engine for nuclear circulatory support systems

    International Nuclear Information System (INIS)

    Watelet, R.P.; Ruggles, A.E.; Torti, V.

    1976-01-01

    Based on the annular version of the Tidal Regenerator Engine, a packaged energy system for nuclear powered circulatory support systems was developed. Net power output of approximately 3 watts is delivered using a 33-watt heat source for an engine module volume of 0.7 liter and a weight of 1.6 kg. A higher efficiency dual cycle version of the annular engine using a Dowtherm A topping cycle on the basic steam cycle is also under development. Projected system output using this advanced engine is 5 watts for the same sized heat source. Life testing of critical components has demonstrated substantial reliability improvement over earlier designs. Of particular significance is the continuing operation of a complete implantable engine system after 1200 hours. Component life testing is continuing with over five thousand hours accumulated on two pump actuators employing welded metal bellows

  17. International Workshop on Finite Elements for Microwave Engineering (11th) - FEM2012 Student Support Grants

    Science.gov (United States)

    2015-05-22

    and Qing H. Liu*1 1 Department of Electrical and Computer Engineering, Duke University, Box 90291, Durham, NC 27708 2Departamento de Ciencias e...1 Department of Electrical and Computer Engineering, Duke University, Box 90291, Durham, NC 27708 2Departamento de Ciencias e Ingenieŕıa de la...latest methods can be applied. ∗The authors want to acknowledge the support of Ministerio de Educación y Ciencia of Spain under projects TEC2010-18175

  18. Implementation of workflow engine technology to deliver basic clinical decision support functionality.

    Science.gov (United States)

    Huser, Vojtech; Rasmussen, Luke V; Oberg, Ryan; Starren, Justin B

    2011-04-10

    Workflow engine technology represents a new class of software with the ability to graphically model step-based knowledge. We present application of this novel technology to the domain of clinical decision support. Successful implementation of decision support within an electronic health record (EHR) remains an unsolved research challenge. Previous research efforts were mostly based on healthcare-specific representation standards and execution engines and did not reach wide adoption. We focus on two challenges in decision support systems: the ability to test decision logic on retrospective data prior prospective deployment and the challenge of user-friendly representation of clinical logic. We present our implementation of a workflow engine technology that addresses the two above-described challenges in delivering clinical decision support. Our system is based on a cross-industry standard of XML (extensible markup language) process definition language (XPDL). The core components of the system are a workflow editor for modeling clinical scenarios and a workflow engine for execution of those scenarios. We demonstrate, with an open-source and publicly available workflow suite, that clinical decision support logic can be executed on retrospective data. The same flowchart-based representation can also function in a prospective mode where the system can be integrated with an EHR system and respond to real-time clinical events. We limit the scope of our implementation to decision support content generation (which can be EHR system vendor independent). We do not focus on supporting complex decision support content delivery mechanisms due to lack of standardization of EHR systems in this area. We present results of our evaluation of the flowchart-based graphical notation as well as architectural evaluation of our implementation using an established evaluation framework for clinical decision support architecture. We describe an implementation of a free workflow technology

  19. Implementation of workflow engine technology to deliver basic clinical decision support functionality

    Science.gov (United States)

    2011-01-01

    Background Workflow engine technology represents a new class of software with the ability to graphically model step-based knowledge. We present application of this novel technology to the domain of clinical decision support. Successful implementation of decision support within an electronic health record (EHR) remains an unsolved research challenge. Previous research efforts were mostly based on healthcare-specific representation standards and execution engines and did not reach wide adoption. We focus on two challenges in decision support systems: the ability to test decision logic on retrospective data prior prospective deployment and the challenge of user-friendly representation of clinical logic. Results We present our implementation of a workflow engine technology that addresses the two above-described challenges in delivering clinical decision support. Our system is based on a cross-industry standard of XML (extensible markup language) process definition language (XPDL). The core components of the system are a workflow editor for modeling clinical scenarios and a workflow engine for execution of those scenarios. We demonstrate, with an open-source and publicly available workflow suite, that clinical decision support logic can be executed on retrospective data. The same flowchart-based representation can also function in a prospective mode where the system can be integrated with an EHR system and respond to real-time clinical events. We limit the scope of our implementation to decision support content generation (which can be EHR system vendor independent). We do not focus on supporting complex decision support content delivery mechanisms due to lack of standardization of EHR systems in this area. We present results of our evaluation of the flowchart-based graphical notation as well as architectural evaluation of our implementation using an established evaluation framework for clinical decision support architecture. Conclusions We describe an implementation of

  20. Leakage Account for Radial Face Contact Seal in Aircraft Engine Support

    Science.gov (United States)

    Vinogradov, A. S.; Sergeeva, T. V.

    2018-01-01

    The article is dedicated to the development of a methodology for the radial face contact seal design taking into consideration the supporting elements deformations in different aircraft engine operating modes. Radial face contact seals are popular in the aircraft engines bearing support. However, there are no published leakage calculation methodologies of these seals. Radial face contact seal leakage is determined by the gap clearance in the carbon seal ring split. In turn, the size gap clearance depends on the deformation of the seal assembly parts and from the engine operation. The article shows the leakage detection sequence in the intershaft radial face contact seal of the compressor support for take-off and cruising modes. Evaluated calculated leakage values (2.4 g/s at takeoff and 0.75 g/s at cruising) go with experience in designing seals.

  1. A volume of intersection approach for on-the-fly system matrix calculation in 3D PET image reconstruction

    International Nuclear Information System (INIS)

    Lougovski, A; Hofheinz, F; Maus, J; Schramm, G; Will, E; Hoff, J van den

    2014-01-01

    The aim of this study is the evaluation of on-the-fly volume of intersection computation for system’s geometry modelling in 3D PET image reconstruction. For this purpose we propose a simple geometrical model in which the cubic image voxels on the given Cartesian grid are approximated with spheres and the rectangular tubes of response (ToRs) are approximated with cylinders. The model was integrated into a fully 3D list-mode PET reconstruction for performance evaluation. In our model the volume of intersection between a voxel and the ToR is only a function of the impact parameter (the distance between voxel centre to ToR axis) but is independent of the relative orientation of voxel and ToR. This substantially reduces the computational complexity of the system matrix calculation. Based on phantom measurements it was determined that adjusting the diameters of the spherical voxel size and the ToR in such a way that the actual voxel and ToR volumes are conserved leads to the best compromise between high spatial resolution, low noise, and suppression of Gibbs artefacts in the reconstructed images. Phantom as well as clinical datasets from two different PET systems (Siemens ECAT HR + and Philips Ingenuity-TF PET/MR) were processed using the developed and the respective vendor-provided (line of intersection related) reconstruction algorithms. A comparison of the reconstructed images demonstrated very good performance of the new approach. The evaluation showed the respective vendor-provided reconstruction algorithms to possess 34–41% lower resolution compared to the developed one while exhibiting comparable noise levels. Contrary to explicit point spread function modelling our model has a simple straight-forward implementation and it should be easy to integrate into existing reconstruction software, making it competitive to other existing resolution recovery techniques. (paper)

  2. NASA Supportability Engineering Implementation Utilizing DoD Practices and Processes

    Science.gov (United States)

    Smith, David A.; Smith, John V.

    2010-01-01

    The Ares I design and development program made the determination early in the System Design Review Phase to utilize DoD ILS and LSA approach for supportability engineering as an integral part of the system engineering process. This paper is to provide a review of the overall approach to design Ares-I with an emphasis on a more affordable, supportable, and sustainable launch vehicle. Discussions will include the requirements development, design influence, support concept alternatives, ILS and LSA planning, Logistics support analyses/trades performed, LSA tailoring for NASA Ares Program, support system infrastructure identification, ILS Design Review documentation, Working Group coordination, and overall ILS implementation. At the outset, the Ares I Project initiated the development of the Integrated Logistics Support Plan (ILSP) and a Logistics Support Analysis process to provide a path forward for the management of the Ares-I ILS program and supportability analysis activities. The ILSP provide the initial planning and coordination between the Ares-I Project Elements and Ground Operation Project. The LSA process provided a system engineering approach in the development of the Ares-I supportability requirements; influence the design for supportability and development of alternative support concepts that satisfies the program operability requirements. The LSA planning and analysis results are documented in the Logistics Support Analysis Report. This document was required during the Ares-I System Design Review (SDR) and Preliminary Design Review (PDR) review cycles. To help coordinate the LSA process across the Ares-I project and between programs, the LSA Report is updated and released quarterly. A System Requirement Analysis was performed to determine the supportability requirements and technical performance measurements (TPMs). Two working groups were established to provide support in the management and implement the Ares-I ILS program, the Integrated Logistics

  3. Temporary septic holding tank at the 100-D remedial action support facility -- Engineering report. Revision 1

    International Nuclear Information System (INIS)

    Kelty, G.G.

    1996-09-01

    This document provides an engineering evaluation for the temporary septic holding tank that will be installed at the 100-D Remedial Action Support Facility at the 100-DR-1 Operable Unit in the Hanford Site. This support facility will be installed at the 100-DR-1 Operable Unit to provide office and work space for the workers involved in remediation activities of the various waste sites located at the Hanford Site

  4. An engineering approach to modelling, decision support and control for sustainable systems.

    Science.gov (United States)

    Day, W; Audsley, E; Frost, A R

    2008-02-12

    Engineering research and development contributes to the advance of sustainable agriculture both through innovative methods to manage and control processes, and through quantitative understanding of the operation of practical agricultural systems using decision models. This paper describes how an engineering approach, drawing on mathematical models of systems and processes, contributes new methods that support decision making at all levels from strategy and planning to tactics and real-time control. The ability to describe the system or process by a simple and robust mathematical model is critical, and the outputs range from guidance to policy makers on strategic decisions relating to land use, through intelligent decision support to farmers and on to real-time engineering control of specific processes. Precision in decision making leads to decreased use of inputs, less environmental emissions and enhanced profitability-all essential to sustainable systems.

  5. An Empirical Evaluation of an Activity-Based Infrastructure for Supporting Cooperation in Software Engineering

    DEFF Research Database (Denmark)

    Tell, Paolo; Babar, Muhammad Ali

    2016-01-01

    Software engineering (SE) is predominantly a team effort that needs close cooperation among several people who may be geographically distributed. It has been recognized that appropriate tool support is a prerequisite to improve cooperation within SE teams. In an effort to contribute to this line...

  6. EIIS: An Educational Information Intelligent Search Engine Supported by Semantic Services

    Science.gov (United States)

    Huang, Chang-Qin; Duan, Ru-Lin; Tang, Yong; Zhu, Zhi-Ting; Yan, Yong-Jian; Guo, Yu-Qing

    2011-01-01

    The semantic web brings a new opportunity for efficient information organization and search. To meet the special requirements of the educational field, this paper proposes an intelligent search engine enabled by educational semantic support service, where three kinds of searches are integrated into Educational Information Intelligent Search (EIIS)…

  7. I-PFO: the new technology for simple and flexible implementation of high productive on-the-fly remote processes

    Science.gov (United States)

    Müllegger, Andreas; Ryba, Tracey

    2017-02-01

    Standardized production systems which can be implemented, programmed, maintained and sourced in a simple and efficient way are key for a successful global production of automobiles or related parts at component suppliers. This is also valid for systems, which are built by laser based processes. One of the key applications is remote laser welding (RLW) of "Body in White" (BIW) parts (such as hang-on parts, B-Pillars, side frames, etc.), but also builtin components (such as car seats, batteries, etc.). The majority of RLW applications are based on the implementation of a 3-D scanner optic (e.g. the PFO 3D from TRUMPF) which positions the laser beam on the various component surfaces to be welded. Over the past 10 years it has been proven that the most efficient way to build up the RLW process is to have a system where an industrial robot and a scanner optic are combined in one production cell. They usually cooperate within an "On-The-Fly" (OTF) process as this ensures minimum cycle times. Until now there are several technologies on the market which can coordinate both the robot and scanner in the OTF mode. But none of them meet all requirements of global standardized production solutions. With the introduction of the I-PFO (Intelligent Programmable Focusing Optics) technology the situation has changed. It is now possible to program or adopt complex remote processes in a fast and easy way by the "Teach-in" function via the robot teach pendant. Additionally a 3D offline designer software is an option for this system. It automatically creates the ideal remote process based on the part, fixture, production cell and required process parameters. The I-PFO technology doesn't need additional hardware due to the fact that it runs on the controller within the PFO 3D. Furthermore it works together with different types of industrial robots (e.g. ABB, Fanuc and KUKA) which allow highest flexibility for the production planning phase. Finally a single TRUMPF laser source can supply

  8. Engineering catalytic activity via ion beam bombardment of catalyst supports for vertically aligned carbon nanotube growth

    Science.gov (United States)

    Islam, A. E.; Nikolaev, P.; Amama, P. B.; Zakharov, D.; Sargent, G.; Saber, S.; Huffman, D.; Erford, M.; Semiatin, S. L.; Stach, E. A.; Maruyama, B.

    2015-09-01

    Carbon nanotube growth depends on the catalytic activity of metal nanoparticles on alumina or silica supports. The control on catalytic activity is generally achieved by variations in water concentration, carbon feed, and sample placement on a few types of alumina or silica catalyst supports obtained via thin film deposition. We have recently expanded the choice of catalyst supports by engineering inactive substrates like c-cut sapphire via ion beam bombardment. The deterministic control on the structure and chemistry of catalyst supports obtained by tuning the degree of beam-induced damage have enabled better regulation of the activity of Fe catalysts only in the ion beam bombarded areas and hence enabled controllable super growth of carbon nanotubes. A wide range of surface characterization techniques were used to monitor the catalytically active surface engineered via ion beam bombardment. The proposed method offers a versatile way to control carbon nanotube growth in patterned areas and also enhances the current understanding of the growth process. With the right choice of water concentration, carbon feed and sample placement, engineered catalyst supports may extend the carbon nanotube growth yield to a level that is even higher than the ones reported here, and thus offers promising applications of carbon nanotubes in electronics, heat exchanger, and energy storage.

  9. Hydrophilic nanofibers as new supports for thin film composite membranes for engineered osmosis.

    Science.gov (United States)

    Bui, Nhu-Ngoc; McCutcheon, Jeffrey R

    2013-02-05

    Engineered osmosis (e.g., forward osmosis, pressure-retarded osmosis, direct osmosis) has emerged as a new platform for applications to water production, sustainable energy, and resource recovery. The lack of an adequately designed membrane has been the major challenge that hinders engineered osmosis (EO) development. In this study, nanotechnology has been integrated with membrane science to build a next generation membrane for engineered osmosis. Specifically, hydrophilic nanofiber, fabricated from different blends of polyacrylonitrile and cellulose acetate via electrospinning, was found to be an effective support for EO thin film composite membranes due to its intrinsically wetted open pore structure with superior interconnectivity. The resulting composite membrane exhibits excellent permselectivity while also showing a reduced resistance to mass transfer that commonly impacts EO processes due to its thin, highly porous nanofiber support layer. Our best membrane exhibited a two to three times enhanced water flux and 90% reduction in salt passage when compared to a standard commercial FO membrane. Furthermore, our membrane exhibited one of the lowest structural parameters reported in the open literature. These results indicate that hydrophilic nanofiber supported thin film composite membranes have the potential to be a next generation membrane for engineered osmosis.

  10. Utilizing product configuration systems for supporting the critical parts of the engineering processes

    DEFF Research Database (Denmark)

    Kristjansdottir, Katrin; Shafiee, Sara; Hvam, Lars

    2016-01-01

    Engineering-To-Order (ETO) companies have to respond to increasing demands to provide highly customized and complex products with high quality at competitive prices. In order to respond to those challenges ETO companies have started to implement product configuration systems (PCS) to increase...... to be supported with the PCSs is not described in the current literature. This paper aims to pursue that research opportunity by presenting a framework, which aims to identifying the critical parts of the engineering processes in order to identify where it most beneficial to implement a PCSs and how to prioritize...

  11. Home care decision support using an Arden engine--merging smart home and vital signs data.

    Science.gov (United States)

    Marschollek, Michael; Bott, Oliver J; Wolf, Klaus-H; Gietzelt, Matthias; Plischke, Maik; Madiesh, Moaaz; Song, Bianying; Haux, Reinhold

    2009-01-01

    The demographic change with a rising proportion of very old people and diminishing resources leads to an intensification of the use of telemedicine and home care concepts. To provide individualized decision support, data from different sources, e.g. vital signs sensors and home environmental sensors, need to be combined and analyzed together. Furthermore, a standardized decision support approach is necessary. The aim of our research work is to present a laboratory prototype home care architecture that integrates data from different sources and uses a decision support system based on the HL7 standard Arden Syntax for Medical Logical Modules. Data from environmental sensors connected to a home bus system are stored in a data base along with data from wireless medical sensors. All data are analyzed using an Arden engine with the medical knowledge represented in Medical Logic Modules. Multi-modal data from four different sensors in the home environment are stored in a single data base and are analyzed using an HL7 standard conformant decision support system. Individualized home care decision support must be based on all data available, including context data from smart home systems and medical data from electronic health records. Our prototype implementation shows the feasibility of using an Arden engine for decision support in a home setting. Our future work will include the utilization of medical background knowledge for individualized decision support, as there is no one-size-fits-all knowledge base in medicine.

  12. Research on Life Science and Life Support Engineering Problems of Manned Deep Space Exploration Mission

    Science.gov (United States)

    Qi, Bin; Guo, Linli; Zhang, Zhixian

    2016-07-01

    Space life science and life support engineering are prominent problems in manned deep space exploration mission. Some typical problems are discussed in this paper, including long-term life support problem, physiological effect and defense of varying extraterrestrial environment. The causes of these problems are developed for these problems. To solve these problems, research on space life science and space medical-engineering should be conducted. In the aspect of space life science, the study of space gravity biology should focus on character of physiological effect in long term zero gravity, co-regulation of physiological systems, impact on stem cells in space, etc. The study of space radiation biology should focus on target effect and non-target effect of radiation, carcinogenicity of radiation, spread of radiation damage in life system, etc. The study of basic biology of space life support system should focus on theoretical basis and simulating mode of constructing the life support system, filtration and combination of species, regulation and optimization method of life support system, etc. In the aspect of space medical-engineering, the study of bio-regenerative life support technology should focus on plants cultivation technology, animal-protein production technology, waste treatment technology, etc. The study of varying gravity defense technology should focus on biological and medical measures to defend varying gravity effect, generation and evaluation of artificial gravity, etc. The study of extraterrestrial environment defense technology should focus on risk evaluation of radiation, monitoring and defending of radiation, compound prevention and removal technology of dust, etc. At last, a case of manned lunar base is analyzed, in which the effective schemes of life support system, defense of varying gravity, defense of extraterrestrial environment are advanced respectively. The points in this paper can be used as references for intensive study on key

  13. Tunable reactivity of supported single metal atoms by impurity engineering of the MgO(001) support.

    Science.gov (United States)

    Pašti, Igor A; Johansson, Börje; Skorodumova, Natalia V

    2018-02-28

    Development of novel materials may often require a rational use of high price components, like noble metals, in combination with the possibility to tune their properties in a desirable way. Here we present a theoretical DFT study of Au and Pd single atoms supported by doped MgO(001). By introducing B, C and N impurities into the MgO(001) surface, the interaction between the surface and the supported metal adatoms can be adjusted. Impurity atoms act as strong binding sites for Au and Pd adatoms and can help to produce highly dispersed metal particles. The reactivity of metal atoms supported by doped MgO(001), as probed by CO, is altered compared to their counterparts on pristine MgO(001). We find that Pd atoms on doped MgO(001) are less reactive than on perfect MgO(001). In contrast, Au adatoms bind CO much more strongly when placed on doped MgO(001). In the case of Au on N-doped MgO(001) we find that charge redistribution between the metal atom and impurity takes place even when not in direct contact, which enhances the interaction of Au with CO. The presented results suggest possible ways for optimizing the reactivity of oxide supported metal catalysts through impurity engineering.

  14. How to Boost Engineering Support Via Web 2.0 - Seeds for the Ares Project...and/or Yours?

    Science.gov (United States)

    Scott, David W.

    2010-01-01

    The Mission Operations Laboratory (MOL) at Marshall Space Flight Center (MSFC) is responsible for Engineering Support capability for NASA s Ares launch system development. In pursuit of this, MOL is building the Ares Engineering and Operations Network (AEON), a web-based portal intended to provide a seamless interface to support and simplify two critical activities: a) Access and analyze Ares manufacturing, test, and flight performance data, with access to Shuttle data for comparison. b) Provide archive storage for engineering instrumentation data to support engineering design, development, and test. A mix of NASA-written and COTS software provides engineering analysis tools. A by-product of using a data portal to access and display data is access to collaborative tools inherent in a Web 2.0 environment. This paper discusses how Web 2.0 techniques, particularly social media, might be applied to the traditionally conservative and formal engineering support arena. A related paper by the author [1] considers use

  15. Developing an Ontology-Based Rollover Monitoring and Decision Support System for Engineering Vehicles

    Directory of Open Access Journals (Sweden)

    Feixiang Xu

    2018-05-01

    Full Text Available The increasing number of rollover accidents of engineering vehicles has attracted close attention; however, most researchers focus on the analysis and monitoring of rollover stability indexes and seldom the assessment and decision support for the rollover risk of engineering vehicles. In this context, an ontology-based rollover monitoring and decision support system for engineering vehicles is proposed. The ontology model is built for representing monitored rollover stability data with semantic properties and for constructing semantic relevance among the various concepts involved in the rollover domain. On the basis of this, ontology querying and reasoning methods based on the Simple Protocol and RDF Query Language (SPARQL and Semantic Web Rule Language (SWRL rules are utilized to realize the rollover risk assessment and to obtain suggested measures. PC and mobile applications (APPs have also been developed to implement the above methods. In addition, five sets of rollover stability data for an articulated off-road engineering vehicle under different working conditions were analyzed to verify the accuracy and effectiveness of the proposed system.

  16. Supply Chain Engineering and the Use of a Supporting Knowledge Management Application

    Science.gov (United States)

    Laakmann, Frank

    The future competition in markets will happen between logistics networks and no longer between enterprises. A new approach for supporting the engineering of logistics networks is developed by this research as a part of the Collaborative Research Centre (SFB) 559: "Modeling of Large Networks in Logistics" at the University of Dortmund together with the Fraunhofer-Institute of Material Flow and Logistics founded by Deutsche Forschungsgemeinschaft (DFG). Based on a reference model for logistics processes, the process chain model, a guideline for logistics engineers is developed to manage the different types of design tasks of logistics networks. The technical background of this solution is a collaborative knowledge management application. This paper will introduce how new Internet-based technologies support supply chain design projects.

  17. Hybrid vehicle turbine engine technology support (HVTE-TS) project. 1995--1996 annual report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    This report presents a summary of technical work accomplished on the Hybrid Vehicle Turbine Engine--Technology Support (HVTE-TS) Project during calendar years 1995 and 1996. Work was performed under an initial National Aeronautics and Space Administration (NASA) contract DEN3-336. As of September 1996 the contract administration was transferred to the US Department of Energy (DoE) Chicago Operations Office, and renumbered as DE-AC02-96EE50553. The purpose of the HVTE-TS program is to develop gas turbine engine technology in support of DoE and automotive industry programs exploring the use of gas turbine generator sets in hybrid-electric automotive propulsion systems. The program focus is directed to the development of four key technologies to be applied to advanced turbogenerators for hybrid vehicles: Structural ceramic materials and processes; Low emissions combustion systems; Regenerators and seals systems; and Insulation systems and processes. 60 figs., 9 tabs.

  18. Engineering analysis activities in support of susquehanna unit 1 startup testing and cycle 1 operations

    International Nuclear Information System (INIS)

    Miller, G.D.; Kukielka, C.A.; Olson, L.M.; Refling, J.G.; Roscioli, A.J.; Somma, S.A.

    1985-01-01

    The engineering analysis group is responsible for all nuclear plant systems analysis and reactor analysis activities, excluding fuel management analysis, at Pennsylvania Power and Light Company. These activities include making pretest and posttest predictions of startup tests; analyzing unplanned or unexpected transient events; providing technical training to plant personnel; assisting in the development of emergency drill scenarios; providing engineering evaluations to support design and technical specification changes, and evaluating, assessing, and resolving a number of license conditions. Many of these activities have required the direct use of RETRAN models. Two RETRAN analyses that were completed to support plant operations - a pretest analysis of the turbine trip startup test, and a posttest analysis of the loss of startup transformer event - are investigated. For each case, RETRAN results are compared with available plant data and comparisons are drawn on the acceptability of the performance of the plant systems

  19. Distance Support In-Service Engineering for the High Energy Laser

    Science.gov (United States)

    2015-03-01

    FEL only) o Isoplanatic angle (if available) o Fried coherence length o Object distance o Dwell time o Laser spot size While many of the items...system and the HEL system. Acquisition Sensor Laser Subsystem Beam Shaping Sensor Suile . Range Finder -. Coarse Tracker . Fine Tracker Optical...distribution is unlimited DISTANCE SUPPORT IN-SERVICE ENGINEERING FOR THE HIGH ENERGY LASER by Team Raising HEL from a Distance Cohort 311-133O March

  20. Evaluation of engineering foods for Controlled Ecological Life Support Systems (CELSS)

    Science.gov (United States)

    Karel, M.

    1982-01-01

    The feasibility of developing acceptable and reliable engineered foods for use in controlled ecological support systems (CELSS) was evaluated. Food resupply and regeneration are calculated, flow charts of food processes in a multipurpose food pilot plant are presented, and equipment for a multipurpose food pilot plant and potential simplification of processes are discussed. Food-waste treatment and water usage in food processing and preparation are also considered.

  1. U.S. Capability to Support Ocean Engineering in the Arctic.

    Science.gov (United States)

    1984-11-01

    ntinudoladgsdvlpetlh Arctic will have an effect on its physical and biolociral U.S. Capability *to Support Ocean Engineering in the Arctic Committee on Assessment of...Richard J. Seymour * Exxon Production Research Scripps Institution of Oceanography - Houston, Texas La Jolla, California William Creelman William H... physical and biological environment. A subject of concern and controversy has been the potential effect that oil and gas activities may have on the

  2. Envisioning a Future Decision Support System for Requirements Engineering : A Holistic and Human-centred Perspective

    OpenAIRE

    Alenljung, Beatrice

    2008-01-01

    Complex decision-making is a prominent aspect of requirements engineering (RE) and the need for improved decision support for RE decision-makers has been identified by a number of authors in the research literature. The fundamental viewpoint that permeates this thesis is that RE decision-making can be substantially improved by RE decision support systems (REDSS) based on the actual needs of RE decision-makers as well as the actual generic human decision-making activities that take place in th...

  3. Engineering Support for Handling Controller Conflicts in Energy Storage Systems Applications

    Directory of Open Access Journals (Sweden)

    Claudia Zanabria

    2017-10-01

    Full Text Available Energy storage systems will play a major role in the decarbonization of future sustainable electric power systems, allowing a high penetration of distributed renewable energy sources and contributing to the distribution network stability and reliability. To accomplish this, a storage system is required to provide multiple services such as self-consumption, grid support, peak-shaving, etc. The simultaneous activation of controllers operation may lead to conflicts, as a consequence the execution of committed services is not guaranteed. This paper presents and discusses a solution to the exposed issue by developing an engineering support approach to semi-automatically detect and handle conflicts for multi-usage storage systems applications. To accomplish that an ontology is developed and exploited by model-driven engineering mechanisms. The proposed approach is evaluated by implementing a use case example, where detection of conflicts is automatically done at an early design stage. Besides this, exploitable source code for conflicts resolution is generated and used during the design and prototype stages of controllers development. Thus, the proposed engineering support enhances the design and development of storage system controllers, especially for multi-usage applications.

  4. Shaping the Future Landscape: Catchment Systems Engineering and the Decision Support Matrix Approach

    Science.gov (United States)

    Hewett, Caspar; Quinn, Paul; Wilkinson, Mark; Wainwright, John

    2017-04-01

    Land degradation is widely recognised as one of the great environmental challenges facing humanity today, much of which is directly associated with human activity. The negative impacts of climate change and of the way in which we have engineered the landscape through, for example, agriculture intensification and deforestation, need to be addressed. However, the answer is not a simple matter of doing the opposite of current practice. Nor is non-intervention a viable option. There is a need to bring together approaches from the natural and social sciences both to understand the issues and to act to solve real problems. We propose combining a Catchment Systems Engineering (CSE) approach that builds on existing approaches such as Natural Water Retention Measures, Green infrastructure and Nature-Based Solutions with a multi-scale framework for decision support that has been successfully applied to diffuse pollution and flood risk management. The CSE philosophy follows that of Earth Systems Engineering and Management, which aims to engineer and manage complex coupled human-natural systems in a highly integrated, rational manner. CSE is multi-disciplinary, and necessarily involves a wide range of subject areas including anthropology, engineering, environmental science, ethics and philosophy. It offers a rational approach which accepts the fact that we need to engineer and act to improve the functioning of the existing catchment entity on which we rely. The decision support framework proposed draws on physical and mathematical modelling; Participatory Action Research; and demonstration sites at which practical interventions are implemented. It is predicated on the need to work with stakeholders to co-produce knowledge that leads to proactive interventions to reverse the land degradation we observe today while sustaining the agriculture humanity needs. The philosophy behind CSE and examples of where it has been applied successfully are presented. The Decision Support Matrix

  5. Application and research of recyclable cables in foundation pit support engineering

    Science.gov (United States)

    Zheng, Suping

    2018-05-01

    Anchoring cables are widely used in the construction of foundation pit as a temporary support structure. After the construction is completed, the anchor cables left in the ground will not only cause environmental pollution but also cause a great waste of resources. The emergence of recyclable cable technology, to avoid such problems, to achieve the secondary use of the anchor cable, excavation in the excavation project is more and more widely used. Combined with the design and construction of recoverable anchor cable in engineering practice, the application effect of recoverable anchor cable in foundation pit support is analyzed, and the conclusion that the support effect of recoverable anchor cable is stable and safe can be obtained Recyclable anchor cable in the future support projects to provide a reference.

  6. Nuclear Engineering Education in Support of Thailand’s Nuclear Power Programme

    International Nuclear Information System (INIS)

    Chanyotha, S.; Pengvanich, P.; Nilsuwankosit, S.

    2015-01-01

    This paper aims to introduce the nuclear engineering education at the Department of Nuclear Engineering, Chulalongkon University, Bangkok Thailand. The department has been offering curriculum in nuclear engineering to support the national nuclear power programme since 1970s. It is the oldest established nuclear engineering educational programme in the South East Asia region. Nevertheless, since the nuclear power programme has been postponed several times due to various reasons, the educational programme at the department has been continuously adapted to meet the nation’s needs. Several areas of study have been introduced, including nuclear power engineering, industrial applications of radioisotope, nuclear instrumentation, radioisotope production, radiation processing, environment and safety, nuclear materials, as well as the newly created nuclear security and non-proliferation. With the renewed interest in using nuclear power in Thailand in 2007, the department has been actively assisting both the government and the electric utility in preparing human resources to support the nuclear power programme through various educational and training modules. Realizing the importance of establishing and balancing all 3 aspects of the nuclear 3S (safety, security and safeguard) in Thailand and in the Southeast Asian region. The new curriculum of nuclear security and safeguard programme has been offered since 2013. Since the establishment, the department has produced hundreds of graduates (Diploma, Master’s, and Ph.D. levels) to feed the continuously expanding Thai nuclear industry. The full paper will provide detailed information of the curriculum, the challenges and obstacles that the department has encountered, as well as the national and international linkages which have been established over the years. (author)

  7. 5th National meeting of the SA Institution of Chemical Engineers: chemical engineering in support of industry and society. V. 1-3

    International Nuclear Information System (INIS)

    1988-01-01

    The 5th national meeting of the SA Institution of Chemical Engineering was held from 15-16 August 1988 at Pretoria. The subject scope covered on the meeting include the broad spectrum of work done by the chemical engineer. The main categories include the processing of agricultural products, biotechnology, coal and hydrocarbons, the chemical engineering practice, fluid dynamics, gas treatment, heat and mass transfer, materials of construction, minerals processing, source materials and products, training and education, vapour-liquid equilibrium, and water and effluents. One seminar specifically covers process engineering in the context of nuclear reactors and two other papers cover supported liquid membrane extraction of uranium

  8. Application of a Systems Engineering Approach to Support Space Reactor Development

    International Nuclear Information System (INIS)

    Wold, Scott

    2005-01-01

    In 1992, approximately 25 Russian and 12 U.S. engineers and technicians were involved in the transport, assembly, inspection, and testing of over 90 tons of Russian equipment associated with the Thermionic System Evaluation Test (TSET) Facility. The entire Russian Baikal Test Stand, consisting of a 5.79 m tall vacuum chamber and related support equipment, was reassembled and tested at the TSET facility in less than four months. In November 1992, the first non-nuclear operational test of a complete thermionic power reactor system in the U.S. was accomplished three months ahead of schedule and under budget. A major factor in this accomplishment was the application of a disciplined top-down systems engineering approach and application of a spiral development model to achieve the desired objectives of the TOPAZ International Program (TIP). Systems Engineering is a structured discipline that helps programs and projects conceive, develop, integrate, test and deliver products and services that meet customer requirements within cost and schedule. This paper discusses the impact of Systems Engineering and a spiral development model on the success of the TOPAZ International Program and how the application of a similar approach could help ensure the success of future space reactor development projects

  9. Systems Engineering and Integration for Advanced Life Support System and HST

    Science.gov (United States)

    Kamarani, Ali K.

    2005-01-01

    Systems engineering (SE) discipline has revolutionized the way engineers and managers think about solving issues related to design of complex systems: With continued development of state-of-the-art technologies, systems are becoming more complex and therefore, a systematic approach is essential to control and manage their integrated design and development. This complexity is driven from integration issues. In this case, subsystems must interact with one another in order to achieve integration objectives, and also achieve the overall system's required performance. Systems engineering process addresses these issues at multiple levels. It is a technology and management process dedicated to controlling all aspects of system life cycle to assure integration at all levels. The Advanced Integration Matrix (AIM) project serves as the systems engineering and integration function for the Human Support Technology (HST) program. AIM provides means for integrated test facilities and personnel for performance trade studies, analyses, integrated models, test results, and validated requirements of the integration of HST. The goal of AIM is to address systems-level integration issues for exploration missions. It will use an incremental systems integration approach to yield technologies, baselines for further development, and possible breakthrough concepts in the areas of technological and organizational interfaces, total information flow, system wide controls, technical synergism, mission operations protocols and procedures, and human-machine interfaces.

  10. Temporary septic holding tank at the 300-FF-1 remedial action central support facility -- Engineering report

    International Nuclear Information System (INIS)

    Jackson, G.J.

    1996-09-01

    The 300-FF-1 Remedial Action Support Facility will be required in the 300 Area (at the Hanford Site in Richland, Washington) to support the remedial actions planned for the 300-FF-1 Operable Unit. In conjunction with this project, soils laden with radiological contamination will be excavated, removed, and transported to a permitted disposal facility, if required based upon characterization. This facility will be a temporary, modular building sized to provide office and work space for the supervisors, engineers, and technicians assigned to the project and engaged in the associated field work. Electrical and potable water service to the 300-FF-1 Support Facility will be provided via permanent connections to existing systems. A temporary septic system is desired as opposed to connecting to the existing sewer system due to regulatory issues. The paper describes the project location, geology and flooding potential, design criteria, operations, and maintenance

  11. The Transport of Mass, Energy, and Entropy in Cryogenic Support Struts for Engineering Design

    Science.gov (United States)

    Elchert, J. P.

    2012-01-01

    Engineers working to understand and reduce cryogenic boil-off must solve a variety of transport problems. An important class of nonlinear problems involves the thermal and mechanical design of cryogenic struts. These classic problems are scattered about the literature and typically require too many resources to obtain. So, to save time for practicing engineers, the author presents this essay. Herein, a variety of new, old, and revisited analytical and finite difference solutions of the thermal problem are covered in this essay, along with commentary on approach and assumptions. This includes a few thermal radiation and conduction combined mode solutions with a discussion on insulation, optimum emissivity, and geometrical phenomenon. Solutions to cooling and heat interception problems are also presented, including a discussion of the entropy generation. The literature on the combined mechanical and thermal design of cryogenic support struts is reviewed with an introduction to the associated numerical methods.

  12. Building a Network to Support Girls and Women in Science, Technology, Engineering, and Mathematics

    Science.gov (United States)

    Spears, Jacqueline D.; Dyer, Ruth A.; Franks, Suzanne E.; Montelone, Beth A.

    Women today constitute over half of the U.S. population and almost half of its overall workforce, yet they make up less than a quarter of the science and engineering workforce. Many historical and social factors contribute to this discrepancy, and numerous individual, institutional, and governmental attempts have been made to redress it. However, many of the efforts to promote, include, and engage girls and women in science, technology, engineering, and mathematics (STEM) education and professions have been made in isolation. At Kansas State University, the authors have begun a systemic effort to increase the participation of girls and women in STEM. This article describes the creation and initial activities of a network of partners that includes universities, school districts, corporations, governmental agencies, and nonprofit organizations, assembled under the aegis of a project supported by funding from the National Science Foundation.

  13. Comparative study on the mechanical mechanism of confined concrete supporting arches in underground engineering.

    Science.gov (United States)

    Lv, Zhijin; Qin, Qian; Jiang, Bei; Luan, Yingcheng; Yu, Hengchang

    2018-01-01

    In order to solve the supporting problem in underground engineering with high stress, square steel confined concrete (SQCC) supporting method is adopted to enhance the control on surrounding rocks, and the control effect is remarkable. The commonly used cross section shapes of confined concrete arch are square and circular. At present, designers have no consensus on which kind is more proper. To search for the answer, this paper makes an analysis on the mechanical properties of the two shapes of the cross-sections. A full-scale indoor comparative test was carried out on the commonly used straight-wall semi-circular SQCC arch and circular steel confined concrete arch (CCC arch). This test is based on self-developed full-scale test system for confined concrete arch. Our research, combining with the numerical analysis, shows: (1) SQCC arch is consistent with CCC arch in the deformation and failure mode. The largest damages parts are at the legs of both of them. (2) The SQCC arch's bearing capability is 1286.9 kN, and the CCC arch's ultimate bearing capability is 1072.4kN. Thus, the SQCC arch's bearing capability is 1.2 times that of the CCC arch. (3) The arches are subjected to combined compression and bending, bending moment is the main reason for the arch failure. The section moment of inertia of SQCC arch is 1.26 times of that of CCC arch, and the former is better than the latter in bending performance. The ultimate bearing capacity is positively correlated with the size of the moment of inertia. Based on the above research, the engineering suggestions are as follows: (1) To improve the bearing capacity of the arch, the cross-sectional shape of the chamber should be optimized and the arch bearing mode changed accordingly. (2) The key damaged positions, such as the arch leg, should be reinforced, optimizing the state of force on the arch. SQCC arches should be used for supporting in underground engineering, which is under stronger influence of the bending moment and

  14. Development of support tools for efficient construction of dynamic simulation program for engineering systems

    International Nuclear Information System (INIS)

    Gofuku, Akio

    1993-01-01

    In this study, two support tools are developed for construction of a dynamic simulation program for engineering systems (especially nuclear systems) by combining software modules. These are (1) a sub-system to support the module selection suitable for dynamic simulation and (2) a graphical user interface to support visual construction of simulation programs. The support tools are designed to be independent on the conception of software modules (data communication methods between modules). In the module selection sub-system of item 1, a module is characterized beforehand by keywords for several criteria. The similarity between the characteristic of requested module by users and that of registered modules in the module library is estimated by a weighted average of similarity indexes for criteria. In the module selection sub-system, the weights are flexibly extracted from users by applying the analytic hierarchy process. The graphical user interface helps users to specify both calling order of modules and data transfer between two modules. The availability of the support tools is evaluated by several sample problems of module selection and dynamic simulation model construction. The support tools will be a strong tool for the efficient usage of software modules. (author)

  15. A corporate ALARA engineering support for all EDF nuclear power plan

    Energy Technology Data Exchange (ETDEWEB)

    Quiot, A.; Orjol, A. [Electricite de France (EDF/UTO), 93 - Noisy le Grand (France); Lafferriere, F.; Fraissinet, E. [Electricite de France (EDF-CNPE) du Blayais, 33 - Saint Ciers sur Gironde (France)

    2006-07-01

    Since 1991, EDF has established a national ALARA programme with a very effective result in terms of dose reduction. Of course, EDF management has decided to further improve occupational exposure management and dose reduction (both collective and individuals). Since 2002, one key element allowing reaching the new goals, is the set up of a national corporate engineering as a support for EDF sites for preparing maintenance interventions. Its objective is to reduce occupational exposure with the help of up to date tools and methods. That engineering support consists of a growing up team comprising at the moment about ten engineers, including CAD specialists and health physicists. It is in charge of using very efficient tools such as P.A.N.T.H.E.R. -R.P. to perform national modelling studies concerning the reactor and auxiliary buildings areas, which are the most costly in terms of doses. That tool has been developed initially for the first steam generator replacements by EDF S.E.P.T.E.N. engineering department. It uses friendly user 3D software to create a geometrical model of the concerned area with all existing materials (pipes, valves, concrete walls allowing visualizing on personal computers, each area from all perspectives. Other important inputs for P.A.N.T.H.E.R. R.P. are the quantities of radioisotopes present in each material. The code allows then estimating the dose rates at each location in the area, calculating the contribution of each equipment (i.e sources) in the area to the dose rate in each point; calculating also the contribution of each radio isotope to the dose rates. With the help of these models the engineering is then able to perform in depth generic work areas optimisation studies, taking into account the workload in each workstation. Up to recently these studies were performed only for huge operations such as steam generator replacements, they are now proposed to EDF sites for more usual interventions. The selection of these interventions takes

  16. A corporate ALARA engineering support for all EDF nuclear power plan

    International Nuclear Information System (INIS)

    Quiot, A.; Orjol, A.; Lafferriere, F.; Fraissinet, E.

    2006-01-01

    Since 1991, EDF has established a national ALARA programme with a very effective result in terms of dose reduction. Of course, EDF management has decided to further improve occupational exposure management and dose reduction (both collective and individuals). Since 2002, one key element allowing reaching the new goals, is the set up of a national corporate engineering as a support for EDF sites for preparing maintenance interventions. Its objective is to reduce occupational exposure with the help of up to date tools and methods. That engineering support consists of a growing up team comprising at the moment about ten engineers, including CAD specialists and health physicists. It is in charge of using very efficient tools such as P.A.N.T.H.E.R. -R.P. to perform national modelling studies concerning the reactor and auxiliary buildings areas, which are the most costly in terms of doses. That tool has been developed initially for the first steam generator replacements by EDF S.E.P.T.E.N. engineering department. It uses friendly user 3D software to create a geometrical model of the concerned area with all existing materials (pipes, valves, concrete walls allowing visualizing on personal computers, each area from all perspectives. Other important inputs for P.A.N.T.H.E.R. R.P. are the quantities of radioisotopes present in each material. The code allows then estimating the dose rates at each location in the area, calculating the contribution of each equipment (i.e sources) in the area to the dose rate in each point; calculating also the contribution of each radio isotope to the dose rates. With the help of these models the engineering is then able to perform in depth generic work areas optimisation studies, taking into account the workload in each workstation. Up to recently these studies were performed only for huge operations such as steam generator replacements, they are now proposed to EDF sites for more usual interventions. The selection of these interventions takes

  17. Fire Engine Support and On-scene Time in Prehospital Stroke Care - A Prospective Observational Study.

    Science.gov (United States)

    Puolakka, Tuukka; Väyrynen, Taneli; Erkkilä, Elja-Pekka; Kuisma, Markku

    2016-06-01

    Introduction On-scene time (OST) previously has been shown to be a significant component of Emergency Medical Services' (EMS') operational delay in acute stroke. Since stroke patients are managed routinely by two-person ambulance crews, increasing the number of personnel available on the scene is a possible method to improve their performance. Hypothesis Using fire engine crews to support ambulances on the scene in acute stroke is hypothesized to be associated with a shorter OST. All patients transported to hospital as thrombolysis candidates during a one-year study period were registered by the ambulance crews using a case report form that included patient characteristics and operational EMS data. Seventy-seven patients (41 [53%] male; mean age of 68.9 years [SD=15]; mean Glasgow Coma Score [GCS] of 15 points [IQR=14-15]) were eligible for the study. Forty-five cases were managed by ambulance and fire engine crews together and 32 by the ambulance crews alone. The median ambulance response time was seven minutes (IQR=5-10) and the fire engine response time was six minutes (IQR=5-8). The number of EMS personnel on the scene was six (IQR=5-7) and two (IQR=2-2), and the OST was 21 minutes (IQR=18-26) and 24 minutes (IQR=20-32; P =.073) for the groups, respectively. In a following regression analysis, using stroke as the dispatch code was the only variable associated with short (engine crews to support ambulances in acute stroke care was not associated with a shorter on-scene stay when compared to standard management by two-person ambulance crews alone. Using stroke as the dispatch code was the only variable that was associated independently with a short OST. Puolakka T , Väyrynen T , Erkkilä E-P , Kuisma M . Fire engine support and on-scene time in prehospital stroke care - a prospective observational study. Prehosp Disaster Med. 2016;31(3):278-281.

  18. Development and Engineering Design in Support of "Rover Ranch": A K-12 Outreach Software Project

    Science.gov (United States)

    Pascali, Raresh

    2003-01-01

    A continuation of the initial development started in the summer of 1999, the body of work performed in support of 'ROVer Ranch' Project during the present fellowship dealt with the concrete concept implementation and resolution of the related issues. The original work performed last summer focused on the initial examination and articulation of the concept treatment strategy, audience and market analysis for the learning technologies software. The presented work focused on finalizing the set of parts to be made available for building an AERCam Sprint type robot and on defining, testing and implementing process necessary to convert the design engineering files to VRML files. Through reverse engineering, an initial set of mission critical systems was designed for beta testing in schools. The files were created in ProEngineer, exported to VRML 1.0 and converted to VRML 97 (VRML 2.0) for final integration in the software. Attributes for each part were assigned using an in-house developed JAVA based program. The final set of attributes for each system, their mutual interaction and the identification of the relevant ones to be tracked, still remain to be decided.

  19. Collection of Medical Original Data with Search Engine for Decision Support.

    Science.gov (United States)

    Orthuber, Wolfgang

    2016-01-01

    Medicine is becoming more and more complex and humans can capture total medical knowledge only partially. For specific access a high resolution search engine is demonstrated, which allows besides conventional text search also search of precise quantitative data of medical findings, therapies and results. Users can define metric spaces ("Domain Spaces", DSs) with all searchable quantitative data ("Domain Vectors", DSs). An implementation of the search engine is online in http://numericsearch.com. In future medicine the doctor could make first a rough diagnosis and check which fine diagnostics (quantitative data) colleagues had collected in such a case. Then the doctor decides about fine diagnostics and results are sent (half automatically) to the search engine which filters a group of patients which best fits to these data. In this specific group variable therapies can be checked with associated therapeutic results, like in an individual scientific study for the current patient. The statistical (anonymous) results could be used for specific decision support. Reversely the therapeutic decision (in the best case with later results) could be used to enhance the collection of precise pseudonymous medical original data which is used for better and better statistical (anonymous) search results.

  20. Automated and comprehensive link engineering supporting branched, ring, and mesh network topologies

    Science.gov (United States)

    Farina, J.; Khomchenko, D.; Yevseyenko, D.; Meester, J.; Richter, A.

    2016-02-01

    Link design, while relatively easy in the past, can become quite cumbersome with complex channel plans and equipment configurations. The task of designing optical transport systems and selecting equipment is often performed by an applications or sales engineer using simple tools, such as custom Excel spreadsheets. Eventually, every individual has their own version of the spreadsheet as well as their own methodology for building the network. This approach becomes unmanageable very quickly and leads to mistakes, bending of the engineering rules and installations that do not perform as expected. We demonstrate a comprehensive planning environment, which offers an efficient approach to unify, control and expedite the design process by controlling libraries of equipment and engineering methodologies, automating the process and providing the analysis tools necessary to predict system performance throughout the system and for all channels. In addition to the placement of EDFAs and DCEs, performance analysis metrics are provided at every step of the way. Metrics that can be tracked include power, CD and OSNR, SPM, XPM, FWM and SBS. Automated routine steps assist in design aspects such as equalization, padding and gain setting for EDFAs, the placement of ROADMs and transceivers, and creating regeneration points. DWDM networks consisting of a large number of nodes and repeater huts, interconnected in linear, branched, mesh and ring network topologies, can be designed much faster when compared with conventional design methods. Using flexible templates for all major optical components, our technology-agnostic planning approach supports the constant advances in optical communications.

  1. An Integrated Information Retrieval Support System for Campus Network

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    This paper presents a new integrated information retrieval support system (IIRSS) which can help Web search engines retrieve cross-lingual information from heterogeneous resources stored in multi-databases in Intranet. The IIRSS, with a three-layer architecture, can cooperate with other application servers running in Intranet. By using intelligent agents to collect information and to create indexes on-the-fly, using an access control strategy to confine a user to browsing those accessible documents for him/her through a single portal, and using a new cross-lingual translation tool to help the search engine retrieve documents, the new system provides controllable information access with different authorizations, personalized services, and real-time information retrieval.

  2. Achieving Closure for Bioregenerative Life Support Systems: Engineering and Ecological Challenges, Research Opportunities

    Science.gov (United States)

    Dempster, William; Allen, John P.

    Closed systems are desirable for a number of purposes: space life support systems where precious life-supporting resources need to be kept inside; biospheric systems; where global ecological pro-cesses can be studied in great detail and testbeds where research topics requiring isolation from the outside (e.g. genetically modified organisms; radioisotopes) can be studied in isolation from the outside environment and where their ecological interactions and fluxes can be studied. But to achieve and maintain closure raises both engineering and ecological challenges. Engineering challenges include methods of achieving closure for structures of different materials, and devel-oping methods of allowing energy (for heating and cooling) and information transfer through the materially closed structure. Methods of calculating degree of closure include measuring degradation rates of inert trace gases introduced into the system. An allied problem is devel-oping means of locating where leaks are located so that they may be repaired and degree of closure maintained. Once closure is achieved, methods of dealing with the pressure differen-tials between inside and outside are needed: from inflatable structures which might adjust to the pressure difference to variable volume chambers attached to the life systems component. These issues are illustrated through the engineering employed at Biosphere 2, the Biosphere 2 Test Module and the Laboratory Biosphere and a discussion of methods used by other closed ecological system facility engineers. Ecological challenges include being able to handle faster cycling rates and accentuated daily and seasonal fluxes of critical life elements such as carbon dioxide, oxygen, water, macro-and mico-nutrients. The problems of achieving sustainability in closed systems for life support include how to handle atmospheric dynamics including trace gases, producing a complete human diet and recycling nutrients and maintaining soil fertility, healthy air and

  3. Design study of RL10 derivatives. Volume 3, part 2: Operational and flight support plan. [analysis of transportation requirements for rocket engine in support of space tug program

    Science.gov (United States)

    Shubert, W. C.

    1973-01-01

    Transportation requirements are considered during the engine design layout reviews and maintenance engineering analyses. Where designs cannot be influenced to avoid transportation problems, the transportation representative is advised of the problems permitting remedies early in the program. The transportation representative will monitor and be involved in the shipment of development engine and GSE hardware between FRDC and vehicle manufacturing plant and thereby will be provided an early evaluation of the transportation plans, methods and procedures to be used in the space tug support program. Unanticipated problems discovered in the shipment of development hardware will be known early enough to permit changes in packaging designs and transportation plans before the start of production hardware and engine shipments. All conventional transport media can be used for the movement of space tug engines. However, truck transport is recommended for ready availability, variety of routes, short transit time, and low cost.

  4. Certain Type Turbofan Engine Whole Vibration Model with Support Looseness Fault and Casing Response Characteristics

    Directory of Open Access Journals (Sweden)

    H. F. Wang

    2014-01-01

    Full Text Available Support looseness fault is a type of common fault in aeroengine. Serious looseness fault would emerge under larger unbalanced force, which would cause excessive vibration and even lead to rubbing fault, so it is important to analyze and recognize looseness fault effectively. In this paper, based on certain type turbofan engine structural features, a rotor-support-casing whole model for certain type turbofan aeroengine is established. The rotor and casing systems are modeled by means of the finite element beam method; the support systems are modeled by lumped-mass model; the support looseness fault model is also introduced. The coupled system response is obtained by numerical integral method. In this paper, based on the casing acceleration signals, the impact characteristics of symmetrical stiffness and asymmetric stiffness models are analyzed, finding that the looseness fault would lead to the longitudinal asymmetrical characteristics of acceleration time domain wave and the multiple frequency characteristics, which is consistent with the real trial running vibration signals. Asymmetric stiffness looseness model is verified to be fit for aeroengine looseness fault model.

  5. Efficient "on-the-fly" calculation of Raman spectra from ab-initio molecular dynamics: Application to hydrophobic/hydrophilic solutes in bulk water.

    Science.gov (United States)

    Partovi-Azar, Pouya; Kühne, Thomas D

    2015-11-05

    We present a novel computational method to accurately calculate Raman spectra from first principles. Together with an extension of the second-generation Car-Parrinello method of Kühne et al. (Phys. Rev. Lett. 2007, 98, 066401) to propagate maximally localized Wannier functions together with the nuclei, a speed-up of one order of magnitude can be observed. This scheme thus allows to routinely calculate finite-temperature Raman spectra "on-the-fly" by means of ab-initio molecular dynamics simulations. To demonstrate the predictive power of this approach we investigate the effect of hydrophobic and hydrophilic solutes in water solution on the infrared and Raman spectra. © 2015 Wiley Periodicals, Inc.

  6. IMP: Using microsat technology to support engineering research inside of the International Space Station

    Science.gov (United States)

    Carroll, Kieran A.

    2000-01-01

    This paper describes an International Space Station (ISS) experiment-support facility being developed by Dynacon for the Canadian Space Agency (CSA), based on microsatellite technology. The facility is called the ``Intravehicular Maneuverable Platform,'' or IMP. The core of IMP is a small, free-floating platform (or ``bus'') deployed inside one of the pressurized crew modules of ISS. Exchangeable experimental payloads can then be mounted to the IMP bus, in order to carry out engineering development or demonstration tests, or microgravity science experiments: the bus provides these payloads with services typical of a standard satellite bus (power, attitude control, etc.). The IMP facility takes advantage of unique features of the ISS, such as the Shuttle-based logistics system and the continuous availability of crew members, to greatly reduce the expense of carrying out space engineering experiments. Further cost reduction has been made possible by incorporating technology that Dynacon has developed for use in a current microsatellite mission. Numerous potential payloads for IMP have been identified, and the first of these (a flexible satellite control experiment) is under development by Dynacon and the University of Toronto's Institute for Aerospace Studies, for the CSA. .

  7. Resources to Support Faculty Writing Data Management Plans: Lessons Learned from an Engineering Pilot

    Directory of Open Access Journals (Sweden)

    Natsuko H. Nicholls

    2014-07-01

    Full Text Available Recent years have seen a growing emphasis on the need for improved management of research data. Academic libraries have begun to articulate the conceptual foundations, roles, and responsibilities involved in data management planning and implementation. This paper provides an overview of the Engineering data support pilot at the University of Michigan Library as part of developing new data services and infrastructure. Through this pilot project, a team of librarians had an opportunity to identify areas where the library can play a role in assisting researchers with data management, and has put forth proposals for immediate steps that the library can take in this regard. The paper summarizes key findings from a faculty survey and discusses lessons learned from an analysis of data management plans from accepted NSF proposals. A key feature of this Engineering pilot project was to ensure that these study results will provide a foundation for librarians to educate and assist researchers with managing their data throughout the research lifecycle.

  8. Engineering Analyses of NCSX Modular Coil and Its Supporting Structure for EM Loads

    International Nuclear Information System (INIS)

    Fan, H.M.; Williamson, D.

    2003-01-01

    NCSX modular coil is a major parts of the NCSX coil systems that surround the highly shaped plasma and vacuum vessel. The flexible copper cable conductors are used to form modular coil on both sides of the ''tee'' beam, which is cast inside the supporting shell structure. The Engineering analyses comprise sequentially coupled-field analyses that include an electromagnetic analysis to calculate the magnetic fields and EM forces, and a structural analysis to evaluate the structural responses. In the sequential EM-structural analysis, nodal forces obtained from the EM analysis were applied as ''nodal force'' loads in the subsequent stress analysis using the identical nodal points and elements. The shell model was imported directly from Pro/ENGINEER files in order to obtain an accurate structural representation. The Boolean operations provided by the ANSYS preprocessor were then applied to subdivide the solid model for more desirable finite element meshing. Material properties of the modular coil were based on test results. Analyses using the ANSYS program to evaluate structural responses of the complicated modular coil systems provided a clear understanding of the structural behaviors and the directions for improving the structural design

  9. Chitosan-based scaffolds for the support of smooth muscle constructs in intestinal tissue engineering

    Science.gov (United States)

    Zakhem, Elie; Raghavan, Shreya; Gilmont, Robert R; Bitar, Khalil N

    2012-01-01

    Intestinal tissue engineering is an emerging field due to a growing demand for intestinal lengthening and replacement procedures secondary to massive resections of the bowel. Here, we demonstrate the potential use of a chitosan/collagen scaffold as a 3D matrix to support the bioengineered circular muscle constructs maintain their physiological functionality. We investigated the biocompatibility of chitosan by growing rabbit colonic circular smooth muscle cells (RCSMCs) on chitosan-coated plates. The cells maintained their spindle-like morphology and preserved their smooth muscle phenotypic markers. We manufactured tubular scaffolds with central openings composed of chitosan and collagen in a 1:1 ratio. Concentrically-aligned 3D circular muscle constructs were bioengineered using fibrin-based hydrogel seeded with RCSMCs. The constructs were placed around the scaffold for 2 weeks, after which they were taken off and tested for their physiological functionality. The muscle constructs contracted in response to Acetylcholine (Ach) and potassium chloride (KCl) and they relaxed in response to vasoactive intestinal peptide (VIP). These results demonstrate that chitosan is a biomaterial possibly suitable for intestinal tissue engineering applications. PMID:22483012

  10. Design of Offshore Wind Turbine Support Structures: Selected topics in the field of geotechnical engineering

    DEFF Research Database (Denmark)

    Bakmar, Christian LeBlanc

    .D. thesis was to enable low-cost and low-risk support structures to be designed in order to improve the economic feasibility of future offshore wind farms. The research work was divided in the following four selected research topics in the field of geotechnical engineering, relating to the monopile......Breaking the dependence on fossil fuels offers many opportunities for strengthened competitiveness, technological development and progress. Offshore wind power is a domestic, sustainable and largely untapped energy resource that provides an alternative to fossil fuels, reduces carbon emissions......, and decreases the economic and supply risks associated with reliance on imported fuels. Today, the modern offshore wind turbine offers competitive production prices for renewable energy and is therefore a key technology in achieving the energy and climate goals of the future. The overall aim of this Ph...

  11. Development of decommissioning engineering support system (DEXUS) of the Fugen Nuclear Power Station

    International Nuclear Information System (INIS)

    Iguchi, Yukihiro; Kanehira, Yoshiki; Tochibana, Mitsuo

    2004-01-01

    The Fugen Nuclear Power Station (NPS) was shut down permanently in March 2003, and preparatory activities are underway to decommission the Fugen NPS. An engineering system to support the decommissioning is being developed to create a dismantling plan using state-of-art software such as 3-dimensional computer aided design (3D-CAD) and virtual reality (VR). In particular, an exposure dose evaluation system using VR has been developed and tested. The total system can be used to quantify radioactive waste, to visualize radioactive inventory, to simulate the dismantling plan, to evaluate workload in radiation environments and to optimize the decommissioning plan. The system will also be useful for educating and training workers and for gaining public acceptance. (author)

  12. An innovative bio-engineering retaining structure for supporting unstable soil

    Directory of Open Access Journals (Sweden)

    Gianluca Bella

    2017-04-01

    Full Text Available The paper presents a new prefabricated bio-engineering structure for the support of unstable soil. This prefabricated structure is made of a steel frame which is completely filled with soil and a face made of tree trunks among which scions or autochthonous bushes are planted. Due to the difficulties in interpreting the complex interaction between soil and structure during the installation and lifetime, an in situ test was carried out in order to evaluate the state of stress in the steel frame and to understand the global behavior of the structure under service loads. On the basis of the obtained results, a procedure for checking the structure safety was proposed and discussed. An easy design method was developed during the research. Moreover, the use of this type of prefabricated structure shows several advantages, such as good performances in terms of stabilizing effects, and easy assembly and transport.

  13. A methodology for system-of-systems design in support of the engineering team

    Science.gov (United States)

    Ridolfi, G.; Mooij, E.; Cardile, D.; Corpino, S.; Ferrari, G.

    2012-04-01

    Space missions have experienced a trend of increasing complexity in the last decades, resulting in the design of very complex systems formed by many elements and sub-elements working together to meet the requirements. In a classical approach, especially in a company environment, the two steps of design-space exploration and optimization are usually performed by experts inferring on major phenomena, making assumptions and doing some trial-and-error runs on the available mathematical models. This is done especially in the very early design phases where most of the costs are locked-in. With the objective of supporting the engineering team and the decision-makers during the design of complex systems, the authors developed a modelling framework for a particular category of complex, coupled space systems called System-of-Systems. Once modelled, the System-of-Systems is solved using a computationally cheap parametric methodology, named the mixed-hypercube approach, based on the utilization of a particular type of fractional factorial design-of-experiments, and analysis of the results via global sensitivity analysis and response surfaces. As an applicative example, a system-of-systems of a hypothetical human space exploration scenario for the support of a manned lunar base is presented. The results demonstrate that using the mixed-hypercube to sample the design space, an optimal solution is reached with a limited computational effort, providing support to the engineering team and decision makers thanks to sensitivity and robustness information. The analysis of the system-of-systems model that was implemented shows that the logistic support of a human outpost on the Moon for 15 years is still feasible with currently available launcher classes. The results presented in this paper have been obtained in cooperation with Thales Alenia Space—Italy, in the framework of a regional programme called STEPS. STEPS—Sistemi e Tecnologie per l'EsPlorazione Spaziale is a research

  14. SecurePhone: a mobile phone with biometric authentication and e-signature support for dealing secure transactions on the fly

    Science.gov (United States)

    Ricci, R.; Chollet, G.; Crispino, M. V.; Jassim, S.; Koreman, J.; Olivar-Dimas, M.; Garcia-Salicetti, S.; Soria-Rodriguez, P.

    2006-05-01

    This article presents an overview of the SecurePhone project, with an account of the first results obtained. SecurePhone's primary aim is to realise a mobile phone prototype - the 'SecurePhone' - in which biometrical authentication enables users to deal secure, dependable transactions over a mobile network. The SecurePhone is based on a commercial PDA-phone, supplemented with specific software modules and a customised SIM card. It integrates in a single environment a number of advanced features: access to cryptographic keys through strong multimodal biometric authentication; appending and verification of digital signatures; real-time exchange and interactive modification of (esigned) documents and voice recordings. SecurePhone's 'biometric recogniser' is based on original research. A fused combination of three different biometric methods - speaker, face and handwritten signature verification - is exploited, with no need for dedicated hardware components. The adoption of non-intrusive, psychologically neutral biometric techniques is expected to mitigate rejection problems that often inhibit the social use of biometrics, and speed up the spread of e-signature technology. Successful biometric authentication grants access to SecurePhone's built-in esignature services through a user-friendly interface. Special emphasis is accorded to the definition of a trustworthy security chain model covering all aspects of system operation. The SecurePhone is expected to boost m-commerce and open new scenarios for m-business and m-work, by changing the way people interact and by improving trust and confidence in information technologies, often considered intimidating and difficult to use. Exploitation plans will also explore other application domains (physical and logical access control, securised mobile communications).

  15. Overheads, Safety Analysis and Engineering FY 1995 Site Support Program Plan WBS 6.3.5

    Energy Technology Data Exchange (ETDEWEB)

    DiVincenzo, E.P.

    1994-09-27

    The Safety Analysis & Engineering (SA&E) department provides core competency for safety analysis and risk documentation that supports achievement of the goals and mission as described in the Hanford Mission Plan, Volume I, Site Guidance (DOE-RL 1993). SA&E operations are integrated into the programs that plan and conduct safe waste management, environmental restoration, and operational activities. SA&E personnel are key members of task teams assigned to eliminate urgent risks and inherent threats that exist at the Hanford Site. Key to ensuring protection of public health and safety, and that of onsite workers, are the products and services provided by the department. SA&E will continue to provide a leadership role throughout the DOE complex with innovative, cost-effective approaches to ensuring safety during environmental cleanup operations. The SA&E mission is to provide support to direct program operations through safety analysis and risk documentation and to maintain an infrastructure responsive to the evolutionary climate at the Hanford Site. SA&E will maintain the appropriate skills mix necessary to fulfill the customers need to conduct all operations in a safe and cost-effective manner while ensuring the safety of the public and the onsite worker.

  16. Wrinkling instability in nanoparticle-supported graphene: implications for strain engineering

    Science.gov (United States)

    Cullen, William; Yamamoto, Mahito; Pierre-Louis, Olivier; Huang, Jia; Fuhrer, Michael; Einstein, Theodore

    2013-03-01

    We have carried out a systematic study of the wrinkling instability of graphene membranes supported on SiO2 substrates with randomly placed silica nanoparticles. At small nanoparticle density, monolayer graphene adheres to the substrate and is highly conformal over the nanoparticles. With increasing nanoparticle density, and decreasing nanoparticle separation to ~100 nm, graphene's elastic response dominates substrate adhesion, and elastic stretching energy is reduced by the formation of wrinkles which connect protrusions. Above a critical nanoparticle density, the wrinkles form a percolating network through the sample. As the graphene membrane is made thicker, delamination from the substrate is observed. Since the wrinkling instability acts to remove inhomogeneous in-plane elastic strains through out-of-plane buckling, our results can be used to place limits on the possible in-plane strain magnitudes that may be created in graphene to realized strain-engineered electronic structures.[2] Supported by the UMD NSF-MRSEC under Grant No. DMR 05-20471, the US ONR MURI and UMD CNAM.

  17. Temporary septic holding tank at the 100-C remedial action support facility -- Engineering report

    International Nuclear Information System (INIS)

    Jackson, G.J.

    1996-08-01

    The primary mission of the Hanford Site from 1943 to 1990 was to produce nuclear materials for national defense. Waste disposal activities associated with this mission resulted in the creation of more than 1,000 waste sites contaminated with radioactive and chemically hazardous constituents. Investigation and remediation of these waste sites is governed by the Tri-Party Agreement. The agreement grouped the waste sites into 78 operable units, each of which was to be investigated and remediated separately. The 100 C Remedial Action Support Facility will be required near the 105-C Reactor to support the 105-C Interim Storage Project. This project is part of the decommissioning of the eight surplus reactor buildings along the Columbia River in the 100 Area. This facility, will be a temporary, modular building sized to provide office and work space for the supervisors, engineers, and technicians assigned to the project and engaged in the associated field work. This report describes the project location, geology and potential flooding, design criteria, operations, and maintenance

  18. Tuning the reactivity of Ru nanoparticles by defect engineering of the reduced graphene oxide support

    KAUST Repository

    Liu, Xin

    2014-01-01

    We systematically investigated the electronic structure of Ru nanoparticles supported on various local structures on reduced graphene oxide (rGO) by first-principles-based calculations. We showed that Ru nanoparticles prefer to nucleate at these localized defect structures on rGO, which act as strong trapping sites for Ru nanoparticles and inhibit their aggregation. The binding of Ru nanoparticles to rGO, which is dependent on these local defect structures and correlates with the interfacial charge transfer, determines the electronic structure of the composites. Further study reveals that the performance of these composites against oxygen adsorption changes proportionally with the shift of the d-band center of the nanoparticles. The correlation between the defect structures on rGO and the reactivity of the composites suggests that controlled modification of the graphenic support by defect engineering would be an efficient way to fabricate new transition metal/rGO composites with high stability and desired reactivity. This journal is © the Partner Organisations 2014.

  19. Overheads, Safety Analysis and Engineering FY 1995 Site Support Program Plan WBS 6.3.5

    International Nuclear Information System (INIS)

    DiVincenzo, E.P.

    1994-01-01

    The Safety Analysis ampersand Engineering (SA ampersand E) department provides core competency for safety analysis and risk documentation that supports achievement of the goals and mission as described in the Hanford Mission Plan, Volume I, Site Guidance (DOE-RL 1993). SA ampersand E operations are integrated into the programs that plan and conduct safe waste management, environmental restoration, and operational activities. SA ampersand E personnel are key members of task teams assigned to eliminate urgent risks and inherent threats that exist at the Hanford Site. Key to ensuring protection of public health and safety, and that of onsite workers, are the products and services provided by the department. SA ampersand E will continue to provide a leadership role throughout the DOE complex with innovative, cost-effective approaches to ensuring safety during environmental cleanup operations. The SA ampersand E mission is to provide support to direct program operations through safety analysis and risk documentation and to maintain an infrastructure responsive to the evolutionary climate at the Hanford Site. SA ampersand E will maintain the appropriate skills mix necessary to fulfill the customers need to conduct all operations in a safe and cost-effective manner while ensuring the safety of the public and the onsite worker

  20. Mechanically robust cryogels with injectability and bioprinting supportability for adipose tissue engineering.

    Science.gov (United States)

    Qi, Dianjun; Wu, Shaohua; Kuss, Mitchell A; Shi, Wen; Chung, Soonkyu; Deegan, Paul T; Kamenskiy, Alexey; He, Yini; Duan, Bin

    2018-05-26

    Bioengineered adipose tissues have gained increased interest as a promising alternative to autologous tissue flaps and synthetic adipose fillers for soft tissue augmentation and defect reconstruction in clinic. Although many scaffolding materials and biofabrication methods have been investigated for adipose tissue engineering in the last decades, there are still challenges to recapitulate the appropriate adipose tissue microenvironment, maintain volume stability, and induce vascularization to achieve long-term function and integration. In the present research, we fabricated cryogels consisting of methacrylated gelatin, methacrylated hyaluronic acid, and 4arm poly(ethylene glycol) acrylate (PEG-4A) by using cryopolymerization. The cryogels were repeatedly injectable and stretchable, and the addition of PEG-4A improved the robustness and mechanical properties. The cryogels supported human adipose progenitor cell (HWA) and adipose derived mesenchymal stromal cell adhesion, proliferation, and adipogenic differentiation and maturation, regardless of the addition of PEG-4A. The HWA laden cryogels facilitated the co-culture of human umbilical vein endothelial cells (HUVEC) and capillary-like network formation, which in return also promoted adipogenesis. We further combined cryogels with 3D bioprinting to generate handleable adipose constructs with clinically relevant size. 3D bioprinting enabled the deposition of multiple bioinks onto the cryogels. The bioprinted flap-like constructs had an integrated structure without delamination and supported vascularization. Adipose tissue engineering is promising for reconstruction of soft tissue defects, and also challenging for restoring and maintaining soft tissue volume and shape, and achieving vascularization and integration. In this study, we fabricated cryogels with mechanical robustness, injectability, and stretchability by using cryopolymerization. The cryogels promoted cell adhesion, proliferation, and adipogenic

  1. Undergraduate research internships to support exploratory research in transportation engineering : project final report, Sept. 2008.

    Science.gov (United States)

    2008-09-01

    The Case Western Reserve University Department of Civil Engineering is in the process of expanding its teaching and research activities, Transportation Engineering as part of its initiative in the overall area of Infrastructure Performance and Reliab...

  2. Applying Costs, Risks and Values Evaluation (CRAVE) methodology to Engineering Support Request (ESR) prioritization

    Science.gov (United States)

    Joglekar, Prafulla N.

    1994-01-01

    Given limited budget, the problem of prioritization among Engineering Support Requests (ESR's) with varied sizes, shapes, and colors is a difficult one. At the Kennedy Space Center (KSC), the recently developed 4-Matrix (4-M) method represents a step in the right direction as it attempts to combine the traditional criteria of technical merits only with the new concern for cost-effectiveness. However, the 4-M method was not adequately successful in the actual prioritization of ESRs for the fiscal year 1995 (FY95). This research identifies a number of design issues that should help us to develop better methods. It emphasizes that given the variety and diversity of ESR's one should not expect that a single method could help in the assessment of all ESR's. One conclusion is that a methodology such as Costs, Risks, and Values Evaluation (CRAVE) should be adopted. It also is clear that the development of methods such as 4-M requires input not only from engineers with technical expertise in ESR's but also from personnel with adequate background in the theory and practice of cost-effectiveness analysis. At KSC, ESR prioritization is one part of the Ground Support Working Teams (GSWT) Integration Process. It was discovered that the more important barriers to the incorporation of cost-effectiveness considerations in ESR prioritization lie in this process. The culture of integration, and the corresponding structure of review by a committee of peers, is not conducive to the analysis and confrontation necessary in the assessment and prioritization of ESR's. Without assistance from appropriately trained analysts charged with the responsibility to analyze and be confrontational about each ESR, the GSWT steering committee will continue to make its decisions based on incomplete understanding, inconsistent numbers, and at times, colored facts. The current organizational separation of the prioritization and the funding processes is also identified as an important barrier to the

  3. A HUMAN FACTORS ENGINEERING PROCESS TO SUPPORT HUMAN-SYSTEM INTERFACE DESIGN IN CONTROL ROOM MODERNIZATION

    Energy Technology Data Exchange (ETDEWEB)

    Kovesdi, C.; Joe, J.; Boring, R.

    2017-05-01

    The primary objective of the United States (U.S.) Department of Energy (DOE) Light Water Reactor Sustainability (LWRS) program is to sustain operation of the existing commercial nuclear power plants (NPPs) through a multi-pathway approach in conducting research and development (R&D). The Advanced Instrumentation, Information, and Control (II&C) System Technologies pathway conducts targeted R&D to address aging and reliability concerns with legacy instrumentation and control (I&C) and other information systems in existing U.S. NPPs. Control room modernization is an important part following this pathway, and human factors experts at Idaho National Laboratory (INL) have been involved in conducting R&D to support migration of new digital main control room (MCR) technologies from legacy analog and legacy digital I&C. This paper describes a human factors engineering (HFE) process that supports human-system interface (HSI) design in MCR modernization activities, particularly with migration of old digital to new digital I&C. The process described in this work is an expansion from the LWRS Report INL/EXT-16-38576, and is a requirements-driven approach that aligns with NUREG-0711 requirements. The work described builds upon the existing literature by adding more detail around key tasks and decisions to make when transitioning from HSI Design into Verification and Validation (V&V). The overall objective of this process is to inform HSI design and elicit specific, measurable, and achievable human factors criteria for new digital technologies. Upon following this process, utilities should have greater confidence with transitioning from HSI design into V&V.

  4. The Didactic Engineering for the Math Olympics Teaching: Olympic Situations with Geogebra’s Support

    Directory of Open Access Journals (Sweden)

    Ana Paula Rodrigues Alves Santos

    2018-01-01

    Full Text Available In this article, we intend to present a partial cut of a master's research, in which we describe, in a specific way, two phases determined by Didactic Engineering - ED in the context of the Mathematical Olympiads. Thus, we have the stages of preliminary analyzes and the construction of Olympic situations/a priori analysis. We emphasize in an Olympic situation that is described/structured with the support of GeoGebra software. Intervention through the proper exploitation of software provides the learner with opportunities to overcome certain difficulties/obstacles to an understanding or even conceptual construction in geometry. In this sense, the mentioned Olympic situation was experienced by students of the ninth year of elementary education II, from a private school in the state of Ceara, Brazil. The Olympic situation described proposes the possibility of the construction of metric relations in the triangle rectangle, content referring to the area of plane geometry. The ED is presented in this research, as a vision of complementarity that uses the theory of didactic situations - TSD. In this way, the described Olympic situation represents an alternative to classes directed to the math Olympics, their indication and structure, describes elements related to didactic mediation during the teaching and learning process, which emphasize details that make it possible to control and predict the possible student’s actions, as well as, to provide the experience of more significant didactic situations for geometry study in the Olympic context.

  5. How Nanotechnology and Biomedical Engineering Are Supporting the Identification of Predictive Biomarkers in Neuro-Oncology.

    Science.gov (United States)

    Ganau, Mario; Paris, Marco; Syrmos, Nikolaos; Ganau, Laura; Ligarotti, Gianfranco K I; Moghaddamjou, Ali; Prisco, Lara; Ambu, Rossano; Chibbaro, Salvatore

    2018-02-26

    The field of neuro-oncology is rapidly progressing and internalizing many of the recent discoveries coming from research conducted in basic science laboratories worldwide. This systematic review aims to summarize the impact of nanotechnology and biomedical engineering in defining clinically meaningful predictive biomarkers with a potential application in the management of patients with brain tumors. Data were collected through a review of the existing English literature performed on Scopus, MEDLINE, MEDLINE in Process, EMBASE, and/or Cochrane Central Register of Controlled Trials: all available basic science and clinical papers relevant to address the above-stated research question were included and analyzed in this study. Based on the results of this systematic review we can conclude that: (1) the advances in nanotechnology and bioengineering are supporting tremendous efforts in optimizing the methods for genomic, epigenomic and proteomic profiling; (2) a successful translational approach is attempting to identify a growing number of biomarkers, some of which appear to be promising candidates in many areas of neuro-oncology; (3) the designing of Randomized Controlled Trials will be warranted to better define the prognostic value of those biomarkers and biosignatures.

  6. How Nanotechnology and Biomedical Engineering Are Supporting the Identification of Predictive Biomarkers in Neuro-Oncology

    Directory of Open Access Journals (Sweden)

    Mario Ganau

    2018-02-01

    Full Text Available The field of neuro-oncology is rapidly progressing and internalizing many of the recent discoveries coming from research conducted in basic science laboratories worldwide. This systematic review aims to summarize the impact of nanotechnology and biomedical engineering in defining clinically meaningful predictive biomarkers with a potential application in the management of patients with brain tumors. Data were collected through a review of the existing English literature performed on Scopus, MEDLINE, MEDLINE in Process, EMBASE, and/or Cochrane Central Register of Controlled Trials: all available basic science and clinical papers relevant to address the above-stated research question were included and analyzed in this study. Based on the results of this systematic review we can conclude that: (1 the advances in nanotechnology and bioengineering are supporting tremendous efforts in optimizing the methods for genomic, epigenomic and proteomic profiling; (2 a successful translational approach is attempting to identify a growing number of biomarkers, some of which appear to be promising candidates in many areas of neuro-oncology; (3 the designing of Randomized Controlled Trials will be warranted to better define the prognostic value of those biomarkers and biosignatures.

  7. Temporary septic holding tank at the 100-D remedial action support facility -- Engineering report. Revision 2

    International Nuclear Information System (INIS)

    Kelty, G.G.

    1996-10-01

    The primary mission of the Hanford Site from 1943 to 1990 was to produce nuclear materials for the national defense. Waste disposal activities associated with this mission resulted in the creation of more than 1,000 waste sites contaminated with radioactive and chemical constituents. Investigation and remediation of the wastes sites is governed by the Tri-Party Agreement. This agreement grouped the waste sites into 78 operable units, each of which was to be investigated and remediated separately. Once actual remediation activities begin at the waste sites, a central support facility will be required at each of the reactor areas (100-B/C, 100-D, and 100-H). These facilities will provide office and work space for the supervisors, engineers, and technicians engaged in the field work. The central facilities will be temporary, modular buildings sized to accommodate the anticipated staff, which in turn is determined by the scope of the planned remediation activities. The paper describes the project location, geology and flooding potential, design criteria, operation, and maintenance

  8. Biomedical engineering support. Final report, June 15, 1971--June 30, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Kolff, W.J.; Sandquist, G.; Olsen, D.B.; Smith, L.M.

    1979-01-01

    On June 15, 1971 the Institute for Biomedical Engineering at the University of Utah contracted with the USAEC to provide biomedical support for an Artificial Heart Program. The goal of the program was to conceive, design, construct and test a prototype artificial heart system powered by an implantable radioisotope heat source. The system would serve as a total artificial heart for animal experiments and for studies directed at developing a total heart replacement system for humans. The major responsibilities of the Institute during the eight year contract period were to design, construct and test all blood handling components of the system and prove in vivo accommodation, performance and adequacy of the system in experimental animals. Upon completion of development of the Implantable Version of the Bench Model Blood Pump, a long series of comprehensive in vitro and in vivo experiments were conducted. In vivo experiments with the system conducted in calves demonstrated the general accommodation, adequate performance and good capacity to sustain the calf as a heart model for up to 36 days. During the more successful in vivo experiments the implanted calves were able to eat, drink, stand, exercise on a treadmill, and exhibited normal blood chemistry and pulmonary function.

  9. Exploring the development of a decision support system (DSS) to prioritize engineered nanoparticles for risk assessment

    International Nuclear Information System (INIS)

    Marvin, Hans J. P.; Bouwmeester, Hans; Bakker, Martine; Kroese, E. Dinant; Meent, Dik van de; Bourgeois, Francois; Lokers, Rob; Ham, Henk van der; Verhelst, Lieke

    2013-01-01

    Engineered nanoparticles (ENPs) have gained huge commercial interest because of their unique and size-related physicochemical properties. The diversity and complexity of ENPs is increasing with the introduction of next generation nanoparticles. The current approaches are not able to assess the safety of all types and applications of ENPs. Therefore, we are developing a decision support system (DSS) that helps to identify those ENPs and applications that should get priority in the risk assessment. This DSS smartly uses existing knowledge in publicly available databases. With the aid of vocabularies, knowledge rules and logic reasoning new knowledge will be derived. In this paper, the procedure for a DSS is described. Since this system is open by design, others can re-use and extend the DSS content, and newly developed DSS tools can be easily accommodated, which will make the DSS more effective over the years. Data of newly emerging studies will be used for the validation of the DSS. The results will benefit regulating authorities and scientists focussing on the development of inherently safe ENPs

  10. Biomedical engineering support. Final report, June 15, 1971--June 30, 1979

    International Nuclear Information System (INIS)

    Kolff, W.J.; Sandquist, G.; Olsen, D.B.; Smith, L.M.

    1979-01-01

    On June 15, 1971 the Institute for Biomedical Engineering at the University of Utah contracted with the USAEC to provide biomedical support for an Artificial Heart Program. The goal of the program was to conceive, design, construct and test a prototype artificial heart system powered by an implantable radioisotope heat source. The system would serve as a total artificial heart for animal experiments and for studies directed at developing a total heart replacement system for humans. The major responsibilities of the Institute during the eight year contract period were to design, construct and test all blood handling components of the system and prove in vivo accommodation, performance and adequacy of the system in experimental animals. Upon completion of development of the Implantable Version of the Bench Model Blood Pump, a long series of comprehensive in vitro and in vivo experiments were conducted. In vivo experiments with the system conducted in calves demonstrated the general accommodation, adequate performance and good capacity to sustain the calf as a heart model for up to 36 days. During the more successful in vivo experiments the implanted calves were able to eat, drink, stand, exercise on a treadmill, and exhibited normal blood chemistry and pulmonary function

  11. Space Station Freedom - Configuration management approach to supporting concurrent engineering and total quality management. [for NASA Space Station Freedom Program

    Science.gov (United States)

    Gavert, Raymond B.

    1990-01-01

    Some experiences of NASA configuration management in providing concurrent engineering support to the Space Station Freedom program for the achievement of life cycle benefits and total quality are discussed. Three change decision experiences involving tracing requirements and automated information systems of the electrical power system are described. The potential benefits of concurrent engineering and total quality management include improved operational effectiveness, reduced logistics and support requirements, prevention of schedule slippages, and life cycle cost savings. It is shown how configuration management can influence the benefits attained through disciplined approaches and innovations that compel consideration of all the technical elements of engineering and quality factors that apply to the program development, transition to operations and in operations. Configuration management experiences involving the Space Station program's tiered management structure, the work package contractors, international partners, and the participating NASA centers are discussed.

  12. A corporative ALARA engineering support for all EDF sites a major improvement: the generic work areas optimization studies

    International Nuclear Information System (INIS)

    Quiot, A.; Lebeau, J.

    2005-01-01

    ALARA studies performed by EDF plants are quite simple and empirical. Most often, feedback experience and common sense, with the help of simple calculations allow reaching useful and efficient decisions. This is particularly the case when the exposure situations are not complex, within a simple environment and with a single source, or one major source. However, in more complex cases this is not enough to guarantee that actual ALARA solutions are implemented. EDF has then decided to use its national corporate engineering as a support for its sites. That engineering support is in charge of using very efficient tools such as PANTHER-RP. The objective of the presentation is to describe the engineering process and tools now available at EDF, to illustrate them with a few case studies and to describe the goals and procedures set up by EDF. (authors)

  13. A corporate ALARA engineering support for all EDF sites. A major improvement: the generic work areas optimisation studies

    Energy Technology Data Exchange (ETDEWEB)

    Quiot, Alain [EDF, SPT, UTO, Le Central, Bat. 420, BP 129, 93162 Noisy-le-Grand Cedex (France); Lebeau, Jacques [Electricite de France, ALARA Project, Site Cap Ampere, 1, place Pleyel, 93282 Saint Denis Cedex (France)

    2004-07-01

    ALARA studies performed by EDF plants are quite simple and empirical. Most often, feedback experience and common sense, with the help of simple calculations allow reaching useful and efficient decisions. This is particularly the case when the exposure situations are not complex, within a simple environment and with a single source, or one major source. However, in more complex cases this is not enough to guarantee that actual ALARA solutions are implemented. EDF has then decided to use its national corporate engineering as a support for its sites. That engineering support is in charge of using very efficient tools such as PANTHER-RP. The objective of the presentation is to describe the engineering process and tools now available at EDF, to illustrate them with a few case studies and to describe the goals and procedures set up by EDF. (authors)

  14. Task Order 22 – Engineering and Technical Support, Deep Borehole Field Test. AREVA Summary Review Report

    Energy Technology Data Exchange (ETDEWEB)

    Denton, Mark A. [AREVA Federal Services, Charlotte, NC (United States)

    2016-01-19

    Under Task Order 22 of the industry Advisory and Assistance Services (A&AS) Contract to the Department of Energy (DOE) DE-NE0000291, AREVA has been tasked with providing assistance with engineering, analysis, cost estimating, and design support of a system for disposal of radioactive wastes in deep boreholes (without the use of radioactive waste). As part of this task order, AREVA was requested, through a letter of technical direction, to evaluate Sandia National Laboratory’s (SNL’s) waste package borehole emplacement system concept recommendation using input from DOE and SNL. This summary review report (SRR) documents this evaluation, with its focus on the primary input document titled: “Deep Borehole Field Test Specifications/M2FT-15SN0817091” Rev. 1 [1], hereafter referred to as the “M2 report.” The M2 report focuses on the conceptual design development for the Deep Borehole Field Test (DBFT), mainly the test waste packages (WPs) and the system for demonstrating emplacement and retrieval of those packages in the Field Test Borehole (FTB). This SRR follows the same outline as the M2 report, which allows for easy correlation between AREVA’s review comments, discussion, potential proposed alternatives, and path forward with information established in the M2 report. AREVA’s assessment focused on three primary elements of the M2 report: the conceptual design of the WPs proposed for deep borehole disposal (DBD), the mode of emplacement of the WP into DBD, and the conceptual design of the DBFT. AREVA concurs with the M2 report’s selection of the wireline emplacement mode specifically over the drill-string emplacement mode and generically over alternative emplacement modes. Table 5-1 of this SRR compares the pros and cons of each emplacement mode considered viable for DBD. The primary positive characteristics of the wireline emplacement mode include: (1) considered a mature technology; (2) operations are relatively simple; (3) probability of a

  15. Effect of Intercalated Water on Potassium Ion Transport through Kv1.2 Channels Studied via On-the-Fly Free-Energy Parametrization.

    Science.gov (United States)

    Paz, S Alexis; Maragliano, Luca; Abrams, Cameron F

    2018-05-08

    We introduce a two-dimensional version of the method called on-the-fly free energy parametrization (OTFP) to reconstruct free-energy surfaces using Molecular Dynamics simulations, which we name OTFP-2D. We first test the new method by reconstructing the well-known dihedral angles free energy surface of solvated alanine dipeptide. Then, we use it to investigate the process of K + ions translocation inside the Kv1.2 channel. By comparing a series of two-dimensional free energy surfaces for ion movement calculated with different conditions on the intercalated water molecules, we first recapitulate the widely accepted knock-on mechanism for ion translocation and then confirm that permeation occurs with water molecules alternated among the ions, in accordance with the latest experimental findings. From a methodological standpoint, our new OTFP-2D algorithm demonstrates the excellent sampling acceleration of temperature-accelerated molecular dynamics and the ability to efficiently compute 2D free-energy surfaces. It will therefore be useful in large variety complex biomacromolecular simulations.

  16. Providing healthcare services on-the-fly using multi-player cooperation game theory in Internet of Vehicles (IoV environment

    Directory of Open Access Journals (Sweden)

    Neeraj Kumar

    2015-08-01

    Full Text Available Internet of Vehicles (IoV is a leading technology of the present era. It has gained huge attention with respect to its implementation in wide variety of domains ranging from traffic safety to infotainment applications. However, IoV can also be extended to healthcare domain, where the patients can be provided healthcare services on-the-fly. We extend this novel concept in this paper and refer it as “Healthcare services on-the-fly”. The concept of game theory has been used among the vehicles to access the healthcare services while traveling. The vehicles act as players in the game and tend to form and split coalitions to access these services. Learning automata (LA act as the players for interaction with the environment and take appropriate actions based on reward and penalty. Apart from this, Virtual Machine (VM scheduling algorithm for efficient utilization of resources at cloud level has also been formulated. A stochastic reward net (SRN-based model is used to represent the coalition formation and splitting with respect to availability of resources at cloud level. The performance of the proposed scheme is evaluated using various performance evaluation metrics. The results obtained prove the effectiveness of the proposed scheme in comparison to the best, first, and random fit schemes.

  17. The Design and Development of a Computerized Tool Support for Conducting Senior Projects in Software Engineering Education

    Science.gov (United States)

    Chen, Chung-Yang; Teng, Kao-Chiuan

    2011-01-01

    This paper presents a computerized tool support, the Meetings-Flow Project Collaboration System (MFS), for designing, directing and sustaining the collaborative teamwork required in senior projects in software engineering (SE) education. Among many schools' SE curricula, senior projects serve as a capstone course that provides comprehensive…

  18. Supplemental investigations in support of environmental assessments by the Idaho INEL Oversight Program at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    1992-01-01

    This document reports on the status of supplemental investigations in support of environmental assessments by the Idaho INEL Oversight Program at the Idaho National Engineering Laboratory. Included is information on hydrology studies in wells open through large intervals, unsaturated zone contamination and transport processes, surface water-groundwater interactions, regional groundwater flow, and independent testing of air quality data

  19. List of publications resulting from the Neutron Beam Scattering Programme supported by the Science and Engineering Research Council for 1984

    International Nuclear Information System (INIS)

    1984-12-01

    The paper lists the references of publications resulting from the Neutron Beam Scattering Programme supported by the Science and Engineering Research Council, covering the year 1984, but also including publications from 1983 not given in the previous issue of this listing. (author)

  20. An Analysis of First Year Engineering Students' Satisfaction with a Support Distance Learning Program in Mathematics

    Science.gov (United States)

    Matzakos, Nikolaos M.; Kalogiannakis, Michail

    2018-01-01

    An online support distance-learning program in Mathematics was developed to aid first year engineering students for their transition from the secondary to the tertiary education in order to reinforce deficiencies they may have in mathematical knowledge. The aim of the present study is to examine, firstly, to what extent the attendance of such a…

  1. A CAMAC and FASTBUS engineering test environment supported by a MicroVAX/MicroVMS system

    International Nuclear Information System (INIS)

    Logg, C.A.

    1987-10-01

    A flexible, multiuser engineering test environment has been established for the engineers in SLAC's Electronic Instrumentation Engineering group. The system hardware includes a standard MicroVAX II and MicroVAX I with multiple CAMAC, FASTBUS, and GPIB instrumentation buses. The system software components include MicroVMS licenses with DECNET/SLACNET, FORTRAN, PASCAL, FORTH, and a versatile graphical display package. In addition, there are several software utilities available to facilitate FASTBUS and CAMAC prototype hardware debugging. 16 refs., 7 figs

  2. The inventions technology on water resources to support environmental engineering based infrastructure

    Science.gov (United States)

    Sunjoto, S.

    2017-03-01

    Since the Stockholm Declaration, declared on the United Nation Conference on the Human Environment in Sweden on 5-16 June 1972 and attended the 113 country delegations, all the infrastructure construction should comply the sustainable development. As a consequence, almost research and studies were directing to the environmental aspect of construction including on water resources engineering. This paper will present the inventions which are very useful for the design of infrastructure, especially on the Groundwater engineering. This field has been rapidly developed since the publication of the well known law of flow through porous materials by Henri Darcy in 1856 on his book "Les fontaine publiques de la ville de Dijon". This law states that the discharge through porous media is proportional to the product of the hydraulic gradient, the cross-sectional area normal to the flow and the coefficient of permeability of the material. Forchheimer in 1930 developed a breakthrough formula by simplifying solution in a steady state flow condition especially in the case of radial flow to compute the permeability coefficient of casing hole or tube test with zero inflow discharge. The outflow discharge on the holes is equal to shape factor of tip of casing (F) multiplied by coefficient of permeability of soils (K) and multiplied by hydraulic head (H). In 1988, Sunjoto derived an equation in unsteady state flow condition based on this formula. In 2002, Sunjoto developed several formulas of shape factor as the parameters of the equation. In the beginning this formula is implemented to compute for the dimension of recharge well as the best method of water conservation for the urban area. After a long research this formula can be implemented to compute the drawdown on pumping or coefficient of permeability of soil by pumping test. This method can substitute the former methods like Theis (1935), Cooper-Jacob (1946), Chow (1952), Glover (1966), Papadopulos-Cooper (1967), Todd (1980

  3. Compilation of reports from research supported by the Materials Engineering Branch, Division of Engineering: 1965--1990

    International Nuclear Information System (INIS)

    Hiser, A.L.

    1991-05-01

    Since 1965, the Materials Engineering Branch, Division of Engineering, of the Nuclear Regulatory Commission's Office of Nuclear Regulatory Research, and its predecessors dating back to the Atomic Energy Commission (AEC), has sponsored research programs concerning the integrity of the primary system pressure boundary of light water reactors. The components of concern in these research programs have included the reactor pressure vessel (RPV), steam generators, and the piping. These research programs have covered a broad range of topics, including fracture mechanics analysis and experimental work for RPV and piping applications, inspection method development and qualification, and evaluation of irradiation effects to RPV steels. This report provides as complete a listing as practical of formal technical reports submitted to the NRC by the investigators working on these research programs. This listing includes topical, final and progress reports, and is segmented by topic area. In many cases a report will cover several topics (such as in the case of progress reports of multi-faceted programs), but is listed under only one topic. Therefore, in searching for reports on a specific topic, other related topic areas should be checked also

  4. An eLearning Standard Approach for Supporting PBL in Computer Engineering

    Science.gov (United States)

    Garcia-Robles, R.; Diaz-del-Rio, F.; Vicente-Diaz, S.; Linares-Barranco, A.

    2009-01-01

    Problem-based learning (PBL) has proved to be a highly successful pedagogical model in many fields, although it is not that common in computer engineering. PBL goes beyond the typical teaching methodology by promoting student interaction. This paper presents a PBL trial applied to a course in a computer engineering degree at the University of…

  5. Supporting collaboration in interdisciplinary research of water–energy–food nexus by means of ontology engineering

    Directory of Open Access Journals (Sweden)

    Terukazu Kumazawa

    2017-06-01

    The introduction of ontology engineering approach will enable us to share a common language and a common theoretical basis. But the development of the new method based on ontology engineering is necessary. For example, knowledge structuring according to each perspective of researchers and simple figure accompanied with a reasoned argument in the background are the directions of tool development.

  6. Analyzing Team Based Engineering Design Process in Computer Supported Collaborative Learning

    Science.gov (United States)

    Lee, Dong-Kuk; Lee, Eun-Sang

    2016-01-01

    The engineering design process has been largely implemented in a collaborative project format. Recently, technological advancement has helped collaborative problem solving processes such as engineering design to have efficient implementation using computers or online technology. In this study, we investigated college students' interaction and…

  7. A Strategic Approach for Supporting the Future of Civil Engineering Education in Europe

    Science.gov (United States)

    Angelides, Demos C.; Loukogeorgaki, Eva

    2005-01-01

    A new strategic vision of the extensively debated European higher education is proposed with focus on civil engineering. Civil engineering education for the future is considered with relevance to potential world-wide trends and anticipated societal requirements and, therefore, required employee qualifications of the construction-related providers…

  8. Development and Application of a Systems Engineering Framework to Support Online Course Design and Delivery

    Science.gov (United States)

    Bozkurt, Ipek; Helm, James

    2013-01-01

    This paper develops a systems engineering-based framework to assist in the design of an online engineering course. Specifically, the purpose of the framework is to provide a structured methodology for the design, development and delivery of a fully online course, either brand new or modified from an existing face-to-face course. The main strength…

  9. Employing 3D Virtual Reality and the Unity Game Engine to Support Nuclear Verification Research

    International Nuclear Information System (INIS)

    Patton, T.

    2015-01-01

    This project centres on the development of a virtual nuclear facility environment to assist non-proliferation and nuclear arms control practitioners - including researchers, negotiators, or inspectors - in developing and refining a verification system and secure chain of custody of material or equipment. The platform for creating the virtual facility environment is the Unity 3D game engine. This advanced platform offers both the robust capability and flexibility necessary to support the design goals of the facility. The project also employs Trimble SketchUp and Blender 3D for constructing the model components. The development goal of this phase of the project was to generate a virtual environment that includes basic physics in which avatars can interact with their environment through actions such as picking up objects, operating vehicles, dismantling a warhead through a spherical representation system, opening/closing doors through a custom security access system, and conducting CCTV surveillance. Initial testing of virtual radiation simulation techniques was also explored in preparation for the next phase of development. Some of the eventual utilities and applications for this platform include: 1. conducting live multi-person exercises of verification activities within a single, shared virtual environment, 2. refining procedures, individual roles, and equipment placement in the contexts of non-proliferation or arms control negotiations 3. hands on training for inspectors, and 4. a portable tool/reference for inspectors to use while carrying out inspections. This project was developed under the Multilateral Verification Project, led by the Verification Research, Training and Information Centre (VERTIC) in the United Kingdom, and financed by the Norwegian Ministry of Foreign Affairs. The environment was constructed at the Vienna Center for Disarmament and Non-Proliferation (VCDNP). (author)

  10. Engineering and management of IT-based service systems an intelligent decision-making support systems approach

    CERN Document Server

    Gomez, Jorge; Garrido, Leonardo; Perez, Francisco

    2014-01-01

    Intelligent Decision-Making Support Systems (i-DMSS) are specialized IT-based systems that support some or several phases of the individual, team, organizational or inter-organizational decision making process by deploying some or several intelligent mechanisms. This book pursues the following academic aims: (i) generate a compendium of quality theoretical and applied contributions in Intelligent Decision-Making Support Systems (i-DMSS) for engineering and management IT-based service systems (ITSS); (ii)  diffuse scarce knowledge about foundations, architectures and effective and efficient methods and strategies for successfully planning, designing, building, operating, and evaluating i-DMSS for ITSS, and (iii) create an awareness of, and a bridge between ITSS and i-DMSS academicians and practitioners in the current complex and dynamic engineering and management ITSS organizational. The book presents a collection of 11 chapters referring to relevant topics for both IT service systems and i-DMSS including: pr...

  11. NeuroTessMesh: A Tool for the Generation and Visualization of Neuron Meshes and Adaptive On-the-Fly Refinement

    Directory of Open Access Journals (Sweden)

    Juan J. Garcia-Cantero

    2017-06-01

    Full Text Available Gaining a better understanding of the human brain continues to be one of the greatest challenges for science, largely because of the overwhelming complexity of the brain and the difficulty of analyzing the features and behavior of dense neural networks. Regarding analysis, 3D visualization has proven to be a useful tool for the evaluation of complex systems. However, the large number of neurons in non-trivial circuits, together with their intricate geometry, makes the visualization of a neuronal scenario an extremely challenging computational problem. Previous work in this area dealt with the generation of 3D polygonal meshes that approximated the cells’ overall anatomy but did not attempt to deal with the extremely high storage and computational cost required to manage a complex scene. This paper presents NeuroTessMesh, a tool specifically designed to cope with many of the problems associated with the visualization of neural circuits that are comprised of large numbers of cells. In addition, this method facilitates the recovery and visualization of the 3D geometry of cells included in databases, such as NeuroMorpho, and provides the tools needed to approximate missing information such as the soma’s morphology. This method takes as its only input the available compact, yet incomplete, morphological tracings of the cells as acquired by neuroscientists. It uses a multiresolution approach that combines an initial, coarse mesh generation with subsequent on-the-fly adaptive mesh refinement stages using tessellation shaders. For the coarse mesh generation, a novel approach, based on the Finite Element Method, allows approximation of the 3D shape of the soma from its incomplete description. Subsequently, the adaptive refinement process performed in the graphic card generates meshes that provide good visual quality geometries at a reasonable computational cost, both in terms of memory and rendering time. All the described techniques have been

  12. Organic liquid scintillation detectors for on-the-fly neutron/gamma alarming and radionuclide identification in a pedestrian radiation portal monitor

    Science.gov (United States)

    Paff, Marc Gerrit; Ruch, Marc L.; Poitrasson-Riviere, Alexis; Sagadevan, Athena; Clarke, Shaun D.; Pozzi, Sara

    2015-07-01

    We present new experimental results from a radiation portal monitor based on the use of organic liquid scintillators. The system was tested as part of a 3He-free radiation portal monitor testing campaign at the European Commission's Joint Research Centre in Ispra, Italy, in February 2014. The radiation portal monitor was subjected to a wide range of test conditions described in ANSI N42.35, including a variety of gamma-ray sources and a 20,000 n/s 252Cf source. A false alarm test tested whether radiation portal monitors ever alarmed in the presence of only natural background. The University of Michigan Detection for Nuclear Nonproliferation Group's system triggered zero false alarms in 2739 trials. It consistently alarmed on a variety of gamma-ray sources travelling at 1.2 m/s at a 70 cm source to detector distance. The neutron source was detected at speeds up to 3 m/s and in configurations with up to 8 cm of high density polyethylene shielding. The success of on-the-fly radionuclide identification varied with the gamma-ray source measured as well as with which of two radionuclide identification methods was used. Both methods used a least squares comparison between the measured pulse height distributions to library spectra to pick the best match. The methods varied in how the pulse height distributions were modified prior to the least squares comparison. Correct identification rates were as high as 100% for highly enriched uranium, but as low as 50% for 241Am. Both radionuclide identification algorithms produced mixed results, but the concept of using liquid scintillation detectors for gamma-ray and neutron alarming in radiation portal monitor was validated.

  13. A Case Study of On-the-fly Wide-field Radio Imaging Applied to the Gravitational Wave Event GW151226

    Science.gov (United States)

    Mooley, K. P.; Frail, D. A.; Myers, S. T.; Kulkarni, S. R.; Hotokezaka, K.; Singer, L. P.; Horesh, A.; Kasliwal, M. M.; Cenko, S. B.; Hallinan, G.

    2018-04-01

    We apply a newly developed on-the-fly mosaicing technique on the Jansky Very Large Array (VLA) at 3 GHz in order to carry out a sensitive search for an afterglow from the Advanced LIGO binary black hole merger event GW151226. In three epochs between 1.5 and 6 months post-merger, we observed a 100 deg2 region, with more than 80% of the survey region having an rms sensitivity of better than 150 μJy/beam, in the northern hemisphere with a merger containment probability of 10%. The data were processed in near real time and analyzed to search for transients and variables. No transients were found but we have demonstrated the ability to conduct blind searches in a time-frequency phase space where the predicted afterglow signals are strongest. If the gravitational wave event is contained within our survey region, the upper limit on any late-time radio afterglow from the merger event at an assumed mean distance of 440 Mpc is about 1029 erg s‑1 Hz‑1. Approximately 1.5% of the radio sources in the field showed variability at a level of 30%, and can be attributed to normal activity from active galactic nuclei. The low rate of false positives in the radio sky suggests that wide-field imaging searches at a few Gigahertz can be an efficient and competitive search strategy. We discuss our search method in the context of the recent afterglow detection from GW170817 and radio follow-up in future gravitational wave observing runs.

  14. Multi-state nonadiabatic deactivation mechanism of coumarin revealed by ab initio on-the-fly trajectory surface hopping dynamic simulation.

    Science.gov (United States)

    Gan, Yanzhen; Yue, Ling; Guo, Xugeng; Zhu, Chaoyuan; Cao, Zexing

    2017-05-17

    An on-the-fly trajectory surface hopping dynamic simulation has been performed for revealing the multi-state nonadiabatic deactivation mechanism of coumarin. The mechanism involves three adiabatic excited states, S 3 (ππ*L b ), S 2 (nπ*, ππ*L a ) and S 1 (ππ*L a , nπ*), and the ground state S 0 at the four state-averaged complete active space self-consistent field, SA4-CASSCF(12,10)/6-31G* level of theory. Upon photoexcitation to the third excited state S 3 (ππ*L b ) in the Franck-Condon region, 80% sampling trajectories decay to the dark S 2 (nπ*) state within an average of 5 fs via the conical intersection S 3 (ππ*L b )/S 2 (nπ*), while 20% decay to the S 2 (ππ*L a ) state within an average of 11 fs via the conical intersection S 3 (ππ*L b )/S 2 (ππ*L a ). Then, sampling trajectories via S 2 (nπ*)/S 1 (ππ*L a ) continue with ultrafast decay processes to give a final distribution of quantum yields as follows: 42% stay on the dark S 1 (nπ*) state, 43.3% go back to the ground S 0 state, 12% undergo a ring-opening reaction to the Z-form S 0 (Z) state, and 2.7% go to the E-form S 0 (E) state. The lifetimes of the excited states are estimated as follows: the S 3 state is about 12 fs on average, the S 2 state is about 80 fs, and the S 1 state has a fast component of about 160 fs and a slow component of 15 ps. The simulated ultrafast radiationless deactivation pathways of photoexcited coumarin immediately interpret the experimentally observed weak fluorescence emission.

  15. Situated cognitive engineering: Developing adaptive track handling support for naval command and control centers

    NARCIS (Netherlands)

    Neerincx, M.A.; Brake, G.M. te; Ven, J.G.M. van de; Arciszewski, H.F.R.; Greef, T.E. de; Lindenberg, J.

    2008-01-01

    Dit artikel presenteert een 'situated cognitive engineering' (SCE) methode voor het verkrijgen van een theoretisch en empirisch onderbouwde Requirements Baseline, waarin operationele, human factors, en technische eisen in samenhang naar voren komen. De methode wordt toegelicht met een ontwerp van

  16. Using Self-Determination Theory to build communities of support to aid in the retention of women in engineering

    Science.gov (United States)

    Dell, Elizabeth M.; Verhoeven, Yen; Christman, Jeanne W.; Garrick, Robert D.

    2018-05-01

    Diverse perspectives are required to address the technological problems facing our world. Although women perform as well as their male counterparts in math and science prior to entering college, the numbers of women students entering and completing engineering programmes are far below their representation in the workforce. This paper reports on a qualitative, multiyear study of the experiences of women students in an Engineering Technology programme. The project addressed some of the unique, fundamental challenges that female students face within their programmes, and the authors describe a programmatic framework based on Self-Determination Theory as an intervention for the recruitment and retention of female engineering students. Data from focus groups and interviews show how students were supported in their undergraduate experiences and how inclusive learning environments are needed to further improve outcomes. Conceptual issues and methodological considerations of our outcomes are presented.

  17. Development of continuous pharmaceutical production processes supported by process systems engineering methods and tools

    DEFF Research Database (Denmark)

    Gernaey, Krist; Cervera Padrell, Albert Emili; Woodley, John

    2012-01-01

    The pharmaceutical industry is undergoing a radical transition towards continuous production processes. Systematic use of process systems engineering (PSE) methods and tools form the key to achieve this transition in a structured and efficient way.......The pharmaceutical industry is undergoing a radical transition towards continuous production processes. Systematic use of process systems engineering (PSE) methods and tools form the key to achieve this transition in a structured and efficient way....

  18. U.S. Army Engineering and Support Center, Huntsville, Price Reasonableness Determinations for Federal Supply Schedule Orders for Supplies Need Improvement

    Science.gov (United States)

    2016-03-29

    Army Engineering and Support Center, Huntsville, Price Reasonableness Determinations for Federal Supply Schedule Orders for Supplies Need...0207.000) │ i Results in Brief U.S. Army Engineering and Support Center, Huntsville, Price Reasonableness Determinations for Federal Supply Schedule...officers made determinations of fair and reasonable pricing for General Services Administration Federal supply schedule orders awarded for purchases

  19. Performance-based service acquisition (PBSA) of TRIDENT strategic weapons systems (SWS) technical engineering support (TES) services

    OpenAIRE

    Arcidiacono, William J.

    2003-01-01

    CIVINS (Civilian Institutions) Thesis document Approved for public release ; distribution is unlimited The objective of this thesis is to determine whether the Strategic Systems Programs (SSP) should apply the concepts of Performance-Based Service Acquisition (PBSA) to Strategic Weapons Systems (SWS) Technical Engineering Support (TES) Services. This thesis provides a Department of Defense (DoD), Department of the Navy (DON), and SSP SWS program acquisition and PBSA history background, ...

  20. HPCMP CREATE (trademark)-AV Quality Assurance: Best Practices for Validating and Supporting Computation-Based Engineering Software

    Science.gov (United States)

    2015-09-30

    30/2015 Oct 2008-Sep 2015 HPCMP CREATE™- AV Quality Assurance: Best Practices for Validating and Supporting Computation-Based Engineering Software...2) “Does this tool adequately perform any and all advertised capabilities?” This paper will describe how the HPCMP CREATE Air Vehicles ( AV ...discussed and their strengths and weaknesses within the CREATE- AV framework addressed. Work toward the HPCMP CREATE, Quality Assurance, Aviation

  1. Bioreactors as Engineering Support to Treat Cardiac Muscle and Vascular Disease

    Directory of Open Access Journals (Sweden)

    Diana Massai

    2013-01-01

    Full Text Available Cardiovascular disease is the leading cause of morbidity and mortality in the Western World. The inability of fully differentiated, load-bearing cardiovascular tissues to in vivo regenerate and the limitations of the current treatment therapies greatly motivate the efforts of cardiovascular tissue engineering to become an effective clinical strategy for injured heart and vessels. For the effective production of organized and functional cardiovascular engineered constructs in vitro, a suitable dynamic environment is essential, and can be achieved and maintained within bioreactors. Bioreactors are technological devices that, while monitoring and controlling the culture environment and stimulating the construct, attempt to mimic the physiological milieu. In this study, a review of the current state of the art of bioreactor solutions for cardiovascular tissue engineering is presented, with emphasis on bioreactors and biophysical stimuli adopted for investigating the mechanisms influencing cardiovascular tissue development, and for eventually generating suitable cardiovascular tissue replacements.

  2. Research reactor usage at the Idaho National Engineering Laboratory in support of university research and education

    International Nuclear Information System (INIS)

    Woodall, D.M.; Dolan, T.J.; Stephens, A.G.

    1990-01-01

    The Idaho National Engineering Laboratory is a US Department of Energy laboratory which has a substantial history of research and development in nuclear reactor technologies. There are a number of available nuclear reactor facilities which have been incorporated into the research and training needs of university nuclear engineering programs. This paper addresses the utilization of the Advanced Reactivity Measurement Facility (ARMF) and the Coupled Fast Reactivity Measurement Facility (CFRMF) for thesis and dissertation research in the PhD program in Nuclear Science and Engineering by the University of Idaho and Idaho State University. Other reactors at the INEL are also being used by various members of the academic community for thesis and dissertation research, as well as for research to advance the state of knowledge in innovative nuclear technologies, with the EBR-II facility playing an essential role in liquid metal breeder reactor research. 3 refs

  3. Finding Support in Moodle: A Face-to-Face Chemistry Course for Engineers

    Science.gov (United States)

    de Vega, Carolina Armijo; McAnally-Salas, Lewis

    2011-01-01

    The aim of this paper was to know the students' perceptions of using online support in a chemistry course. To achieve this objective, a qualitative research was conducted over a chemistry course that was imparted in a face-to-face modality using a LMS (learning management system) for on-line support. The supports available in the LMS were forums,…

  4. Exploring the development of a decision support system (DSS) to prioritize engineered nanoparticles for risk assessment

    NARCIS (Netherlands)

    Marvin, H.J.P.; Bouwmeester, H.; Bakker, M.; Kroese, E.D.; Meent, D. van de; Bourgeois, F.; Lokers, R.; Ham, H. van der; Verhelst, L.

    2013-01-01

    Engineered nanoparticles (ENPs) have gained huge commercial interest because of their unique and size-related physicochemical properties. The diversity and complexity of ENPs is increasing with the introduction of next generation nanoparticles. The current approaches are not able to assess the

  5. Evolutionary, Unconscious Design Support for the Architectural, Engineering and Construction Industry

    NARCIS (Netherlands)

    Van de Ruitenbeek, H.K.M.

    2012-01-01

    The Architecture, Engineering and Construction (AEC) industry is a complex system in which carpenters, structural designers, architects, modellers, cost estimators, planners, politicians and many others act apart together in project-specific virtual enterprises. There is a large amount of actors, an

  6. An online support site for preparation of oral presentations in science and engineering

    Science.gov (United States)

    Kunioshi, Nílson; Noguchi, Judy; Hayashi, Hiroko; Tojo, Kazuko

    2012-12-01

    Oral communication skills are essential for engineers today and, as they are included in accreditation criteria of educational programmes, their teaching and evaluation deserve attention. However, concrete aspects as to what should be taught and evaluated in relation to oral communication skills have not been sufficiently established. In this paper, a method to aid the efficient teaching of oral presentation skills is proposed, from the presentation structure level to word and sentence level choices, through the use of JECPRESE, The Japanese-English Corpus of Presentations in Science and Engineering. As of June 2012, the corpus is composed of transcriptions of 74 presentations delivered in Japanese by students graduating from the Master's programme of various engineering departments and 31 presentations delivered in English, 16 by experienced researchers at an international conference on chemistry, and 15 by undergraduate engineering students of a mid-sized American university. The utterances were classified according to the specific moves (sections of the speech that express specific speaker intent) appearing in the presentations and frequently used words/expressions to express these moves were identified.

  7. Program plan for US Department of Energy support for nuclear engineering education

    International Nuclear Information System (INIS)

    Perkins, L.

    1992-01-01

    This document describes the plan developed to address the growing concern for the continued deterioration of nuclear engineering education in the United States and its ability to meet the manpower demands for this Nation's work force requiring nuclear related talent in the foreseeable future

  8. Support vector machine to predict diesel engine performance and emission parameters fueled with nano-particles additive to diesel fuel

    Science.gov (United States)

    Ghanbari, M.; Najafi, G.; Ghobadian, B.; Mamat, R.; Noor, M. M.; Moosavian, A.

    2015-12-01

    This paper studies the use of adaptive Support Vector Machine (SVM) to predict the performance parameters and exhaust emissions of a diesel engine operating on nanodiesel blended fuels. In order to predict the engine parameters, the whole experimental data were randomly divided into training and testing data. For SVM modelling, different values for radial basis function (RBF) kernel width and penalty parameters (C) were considered and the optimum values were then found. The results demonstrate that SVM is capable of predicting the diesel engine performance and emissions. In the experimental step, Carbon nano tubes (CNT) (40, 80 and 120 ppm) and nano silver particles (40, 80 and 120 ppm) with nanostructure were prepared and added as additive to the diesel fuel. Six cylinders, four-stroke diesel engine was fuelled with these new blended fuels and operated at different engine speeds. Experimental test results indicated the fact that adding nano particles to diesel fuel, increased diesel engine power and torque output. For nano-diesel it was found that the brake specific fuel consumption (bsfc) was decreased compared to the net diesel fuel. The results proved that with increase of nano particles concentrations (from 40 ppm to 120 ppm) in diesel fuel, CO2 emission increased. CO emission in diesel fuel with nano-particles was lower significantly compared to pure diesel fuel. UHC emission with silver nano-diesel blended fuel decreased while with fuels that contains CNT nano particles increased. The trend of NOx emission was inverse compared to the UHC emission. With adding nano particles to the blended fuels, NOx increased compared to the net diesel fuel. The tests revealed that silver & CNT nano particles can be used as additive in diesel fuel to improve complete combustion of the fuel and reduce the exhaust emissions significantly.

  9. CROSS: A GDSS for the Evaluation and Prioritization of Engineering Support Requests and Advanced Technology Projects at NASA

    Science.gov (United States)

    Tavana, Madjid; Lee, Seunghee

    1996-01-01

    Objective evaluation and prioritization of engineering support requests (ESRs) is a difficult task at the Kennedy Space Center (KSC) Shuttle Project Engineering Office. The difficulty arises from the complexities inherent in the evaluation process and the lack of structured information. The purpose of this project is to implement the consensus ranking organizational support system (CROSS), a multiple criteria decision support system (DSS) developed at KSC that captures the decision maker's beliefs through a series of sequential, rational, and analytical processes. CROSS utilizes the analytic hierarchy process (AHP), subjective probabilities, entropy concept, and maximize agreement heuristic (MAH) to enhance the decision maker's intuition in evaluation ESRs. Some of the preliminary goals of the project are to: (1) revisit the structure of the ground systems working team (GWST) steering committee, (2) develop a template for ESR originators to provide more comple and consistent information to the GSWT steering committee members to eliminate the need for a facilitator, (3) develop an objective and structured process for the initial screening of ESRs, (4) extensive training of the stakeholders and the GWST steering committee to eliminate the need for a facilitator, (5) automate the process as much as possible, (6) create an environment to compile project success factor data on ESRs and move towards a disciplined system that could be used to address supportability threshold issues at the KSC, and (7) investigate the possibility of an organization-wide implementation of CROSS.

  10. Ford/BASF/UM Activities in Support of the Hydrogen Storage Engineering Center of Excellence

    Energy Technology Data Exchange (ETDEWEB)

    Veenstra, Mike [Ford Motor Company, Dearborn, MI (United States); Purewal, Justin [Ford Motor Company, Dearborn, MI (United States); Xu, Chunchuan [Ford Motor Company, Dearborn, MI (United States); Yang, Jun [Ford Motor Company, Dearborn, MI (United States); Blaser, Rachel [Ford Motor Company, Dearborn, MI (United States); Sudik, Andrea [Ford Motor Company, Dearborn, MI (United States); Siegel, Don [Univ. of Michigan, Ann Arbor, MI (United States); Ming, Yang [Univ. of Michigan, Ann Arbor, MI (United States); Liu, Dong' an [Univ. of Michigan, Ann Arbor, MI (United States); Chi, Hang [Univ. of Michigan, Ann Arbor, MI (United States); Gaab, Manuela [BASF SE, Ludwigshafen (Germany); Arnold, Lena [BASF SE, Ludwigshafen (Germany); Muller, Ulrich [BASF SE, Ludwigshafen (Germany)

    2015-06-30

    Widespread adoption of hydrogen as a vehicular fuel depends critically on the development of low-cost, on-board hydrogen storage technologies capable of achieving high energy densities and fast kinetics for hydrogen uptake and release. As present-day technologies -- which rely on physical storage methods such as compressed hydrogen -- are incapable of attaining established Department of Energy (DOE) targets, development of materials-based approaches for storing hydrogen have garnered increasing attention. Material-based storage technologies have potential to store hydrogen beyond twice the density of liquid hydrogen. To hasten development of these ‘hydride’ materials, the DOE previously established three centers of excellence for materials storage R&D associated with the key classes of materials: metal hydrides, chemical hydrogen, and adsorbents. While these centers made progress in identifying new storage materials, the challenges associated with the engineering of the system around a candidate storage material are in need of further advancement. In 2009 the DOE established the Hydrogen Storage Engineering Center of Excellence with the objective of developing innovative engineering concepts for materials-based hydrogen storage systems. As a partner in the Hydrogen Storage Engineering Center of Excellence, the Ford-UM-BASF team conducted a multi-faceted research program that addresses key engineering challenges associated with the development of materials-based hydrogen storage systems. First, we developed a novel framework that allowed for a material-based hydrogen storage system to be modeled and operated within a virtual fuel cell vehicle. This effort resulted in the ability to assess dynamic operating parameters and interactions between the storage system and fuel cell power plant, including the evaluation of performance throughout various drive cycles. Second, we engaged in cost modeling of various incarnations of the storage systems. This analysis

  11. Analysis of design characteristics of a V-type support using an advanced engineering environment

    Science.gov (United States)

    Gwiazda, A.; Banaś, W.; Sękala, A.; Cwikla, G.; Topolska, S.; Foit, K.; Monica, Z.

    2017-08-01

    Modern mining support, for the entire period of their use, is the important part of the mining complex, which includes all the devices in the excavation during his normal use. Therefore, during the design of the support, it is an important task to choose the shape and to select the dimensions of a support as well as its strength characteristics. According to the rules, the design process of a support must take into account, inter alia, the type and the dimensions of the expected means of transport, the number and size of pipelines, and the type of additional equipment used excavation area. The support design must ensure the functionality of the excavation process and job security, while maintaining the economic viability of the entire project. Among others it should ensure the selection of a support for specific natural conditions. It is also important to take into consideration the economic characteristics of the project. The article presents an algorithm of integrative approach and its formalized description in the form of integration the areas of different construction characteristics optimization of a V-type mining support. The paper includes the example of its application for developing the construction of this support. In the paper is also described the results of the characteristics analysis and changings that were introduced afterwards. The support models are prepared in the computer environment of the CAD class (Siemens NX PLM). Also the analyses were conducted in this design, graphical environment.

  12. Virtual Environment Computer Simulations to Support Human Factors Engineering and Operations Analysis for the RLV Program

    Science.gov (United States)

    Lunsford, Myrtis Leigh

    1998-01-01

    The Army-NASA Virtual Innovations Laboratory (ANVIL) was recently created to provide virtual reality tools for performing Human Engineering and operations analysis for both NASA and the Army. The author's summer research project consisted of developing and refining these tools for NASA's Reusable Launch Vehicle (RLV) program. Several general simulations were developed for use by the ANVIL for the evaluation of the X34 Engine Changeout procedure. These simulations were developed with the software tool dVISE 4.0.0 produced by Division Inc. All software was run on an SGI Indigo2 High Impact. This paper describes the simulations, various problems encountered with the simulations, other summer activities, and possible work for the future. We first begin with a brief description of virtual reality systems.

  13. Evaluation of engineered foods for Closed Ecological Life Support System (CELSS)

    Science.gov (United States)

    Karel, M.

    1981-01-01

    A system of conversion of locally regenerated raw materials and of resupplied freeze-dried foods and ingredients into acceptable, safe and nutritious engineered foods is proposed. The first phase of the proposed research has the following objectives: (1) evaluation of feasibility of developing acceptable and reliable engineered foods from a limited selection of plants, supplemented by microbially produced nutrients and a minimum of dehydrated nutrient sources (especially those of animal origin); (2) evaluation of research tasks and specifications of research projects to adapt present technology and food science to expected space conditions (in particular, problems arising from unusual gravity conditions, problems of limited size and the isolation of the food production system, and the opportunities of space conditions are considered); (3) development of scenarios of agricultural production of plant and microbial systems, including the specifications of processing wastes to be recycled.

  14. Supporting English-medium pedagogy through an online corpus of science and engineering lectures

    Science.gov (United States)

    Kunioshi, Nílson; Noguchi, Judy; Tojo, Kazuko; Hayashi, Hiroko

    2016-05-01

    As English-medium instruction (EMI) spreads around the world, university teachers and students who are non-native speakers of English (NNS) need to put much effort into the delivery or reception of content. Construction of scientific meaning in the process of learning is already complex when instruction is delivered in the first language of the teachers and students, and may become even more challenging in a second language, because science education depends greatly on language. In order to identify important pedagogical functions that teachers use to deliver content and to present different ways to realise each function, a corpus of lectures related to science and engineering courses was created and analysed. NNS teachers and students in science and engineering involved in EMI higher education can obtain insights for delivering and listening to lectures from the Online Corpus of Academic Lectures (OnCAL).

  15. Guidelines to design engineering education in the twenty-first century for supporting innovative product development

    Science.gov (United States)

    Violante, Maria Grazia; Vezzetti, Enrico

    2017-11-01

    In the twenty-first century, meeting our technological challenges demands educational excellence, a skilled populace that is ready for the critical challenges society faces. There is widespread consensus, however, that education systems are failing to adequately prepare all students with the essential twenty-first century knowledge and skills necessary to succeed in life, career, and citizenship. The purpose of this paper is to understand how twenty-first century knowledge and skills can be appropriately embedded in engineering education finalised to innovative product development by using additive manufacturing (AM). The study designs a learning model by which to achieve effective AM education to address the requirements of twenty-first century and to offer students the occasion to experiment with STEM (Science, technology, engineering, and mathematics) concepts. The study is conducted using the quality function deployment (QFD) methodology.

  16. Development of in-service inspection system for core support graphite structures in the high temperature engineering test reactor (HTTR)

    Energy Technology Data Exchange (ETDEWEB)

    Sumita, Junya; Hanawa, Satoshi; Kikuchi, Takayuki; Ishihara, Masahiro [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment

    2003-03-01

    Visual inspection of core support graphite structures using TV camera as in-service inspection and measurement of material characteristics using surveillance test specimens are planned in the High Temperature Engineering Test Reactor (HTTR) to confirm structural integrity of the core support graphite structures. For the visual inspection, in-service inspection system developed from September 1996 to June 1998, and pre-service inspection using the system was carried out. As the result of the pre-service inspection, it was validated that high quality of visual inspection with TV camera can be carried out, and also structural integrity of the core support graphite structures at the initial stage of the HTTR operation was confirmed. (author)

  17. Using a Formal Approach for Reverse Engineering and Design Recovery to Support Software Reuse

    Science.gov (United States)

    Gannod, Gerald C.

    2002-01-01

    This document describes 3rd year accomplishments and summarizes overall project accomplishments. Included as attachments are all published papers from year three. Note that the budget for this project was discontinued after year two, but that a residual budget from year two allowed minimal continuance into year three. Accomplishments include initial investigations into log-file based reverse engineering, service-based software reuse, and a source to XML generator.

  18. Automated support for system's engineering and operations - The development of new paradigms

    Science.gov (United States)

    Truszkowski, Walt; Hall, Gardiner A.; Jaworski, Allan; Zoch, David

    1992-01-01

    Technological developments in spacecraft ground operations are reviewed. The technological, operations-oriented, managerial, and economic factors driving the evolution of the Mission Operations Control Center (MOCC), and its predecessor the Operational Control Center are examined. The functional components of the various MOCC subsystems are outlined. A brief overview is given of the concepts behind the The Knowledge-Based Software Engineering Environment, the Generic Spacecraft Analysis Assistant, and the Knowledge From Pictures tool.

  19. Evolutionary, Unconscious Design Support for the Architectural, Engineering and Construction Industry

    OpenAIRE

    Van de Ruitenbeek, H.K.M.

    2012-01-01

    The Architecture, Engineering and Construction (AEC) industry is a complex system in which carpenters, structural designers, architects, modellers, cost estimators, planners, politicians and many others act apart together in project-specific virtual enterprises. There is a large amount of actors, an overwhelming number of ongoing processes, distributed, decentralised organisations and a variety of projects. This complicates efficient communication and supply chain integration which, according...

  20. Bond graph modelling of engineering systems: theory, applications and software support

    National Research Council Canada - National Science Library

    Borutzky, Wolfgang; Margolis, Donald L

    2011-01-01

    ... way such that analytical or computer response predictions can be straightforwardly carried out. Bond graphs are a concise pictorial representation of all types of interacting energetic systems. In my experience working with engineers on the development of complex systems it is obvious that these systems suffer from thermal problems, structural problems, vibration and noise problems, and control and stability issues that do not fit into a single discipline. Bond graphs provide the link by which all these different ...

  1. Requirements for High Level Models Supporting Design Space Exploration in Model-based Systems Engineering

    OpenAIRE

    Haveman, Steven P.; Bonnema, G. Maarten

    2013-01-01

    Most formal models are used in detailed design and focus on a single domain. Few effective approaches exist that can effectively tie these lower level models to a high level system model during design space exploration. This complicates the validation of high level system requirements during detailed design. In this paper, we define requirements for a high level model that is firstly driven by key systems engineering challenges present in industry and secondly connects to several formal and d...

  2. Supporting "The Best and Brightest" in Science and Engineering: NSF Graduate Research Fellowships

    OpenAIRE

    Richard B. Freeman; Tanwin Chang; Hanley Chiang

    2005-01-01

    The National Science Foundation's (NSF) Graduate Research Fellowship (GRF) is a highly prestigious award for science and engineering (S&E) graduate students. This paper uses data from 1952 to 2004 on the population of over 200,000 applicants to the GRF to examine the determinants of the number and characteristics of applicants and the characteristics of awardees. In the early years of the program, GRF awards went largely to physical science and mathematics students and disproportionately to w...

  3. Engineering review of the core support structure of the Gas Cooled Fast Breeder Reactor

    International Nuclear Information System (INIS)

    1978-09-01

    The review of the core support structure of the gas cooled fast breeder reactor (GCFR) covered such areas as the design criteria, the design and analysis of the concepts, the development plan, and the projected manufacturing costs. Recommendations are provided to establish a basis for future work on the GCFR core support structure

  4. Directing chondrogenic differentiation of mesenchymal stem cells with a solid-supported chitosan thermogel for cartilage tissue engineering

    International Nuclear Information System (INIS)

    Huang, Hongjie; Zhang, Xin; Hu, Xiaoqing; Dai, Linghui; Zhu, Jingxian; Man, Zhentao; Ao, Yingfang; Chen, Haifeng; Zhou, Chunyan

    2014-01-01

    Hydrogels are attractive for cartilage tissue engineering because of their high plasticity and similarity with the native cartilage matrix. However, one critical drawback of hydrogels for osteochondral repair is their inadequate mechanical strength. To address this limitation, we constructed a solid-supported thermogel comprising a chitosan hydrogel system and demineralized bone matrix. Scanning electron microscopy, the equilibrium scanning ratio, the biodegradation rate, biomechanical tests, biochemical assays, metabolic activity tests, immunostaining and cartilage-specific gene expression analysis were used to evaluate the solid-supported thermogel. Compared with pure hydrogel or demineralized matrix, the hybrid biomaterial showed superior porosity, equilibrium swelling and degradation rate. The hybrid scaffolds exhibited an increased mechanical strength: 75% and 30% higher compared with pure hydrogels and demineralized matrix, respectively. After three days culture, bone-derived mesenchymal stem cells (BMSCs) maintained viability above 90% in all three materials; however, the cell retention of the hybrid scaffolds was more efficient and uniform than the other materials. Matrix production and chondrogenic differentiation of BMSCs in the hybrid scaffolds were superior to its precursors, based on glycosaminoglycan quantification and hyaline cartilage marker expression after three weeks in culture. Its easy preparation, favourable biophysical properties and chondrogenic capacity indicated that this solid-supported thermogel could be an attractive biomaterial framework for cartilage tissue engineering. (paper)

  5. Preliminary engineering studies for the support shell of the outer tracker of the SDC detector

    International Nuclear Information System (INIS)

    Vandergriff, D.H.; Mayhall, J.

    1991-09-01

    The Solenoidal Detector Collaboration (SDC) detector is in the conceptual design phase. ORNL is currently working with various sub-groups on the design of the outer tracker portion of the SDC detector. A major focus in the outer tracker design is the structure that mounts and supports the tracking elements. This structure must meet extreme requirements of alignment and stability while containing a minimum of material. This report describes the requirements, evaluations, and analyses that have been performed on the two options being explored; a cylindrical support shell and a modular support shell

  6. Engineering cartilaginous grafts using chondrocyte-laden hydrogels supported by a superficial layer of stem cells.

    Science.gov (United States)

    Mesallati, Tariq; Buckley, Conor T; Kelly, Daniel J

    2017-05-01

    During postnatal joint development, progenitor cells that reside in the superficial region of articular cartilage first drive the rapid growth of the tissue and later help direct the formation of mature hyaline cartilage. These developmental processes may provide directions for the optimal structuring of co-cultured chondrocytes (CCs) and multipotent stromal/stem cells (MSCs) required for engineering cartilaginous tissues. The objective of this study was to engineer cartilage grafts by recapitulating aspects of joint development where a population of superficial progenitor cells drives the development of the tissue. To this end, MSCs were either self-assembled on top of CC-laden agarose gels (structured co-culture) or were mixed with CCs before being embedded in an agarose hydrogel (mixed co-culture). Porcine infrapatellar fat pad-derived stem cells (FPSCs) and bone marrow-derived MSCs (BMSCs) were used as sources of progenitor cells. The DNA, sGAG and collagen content of a mixed co-culture of FPSCs and CCs was found to be lower than the combined content of two control hydrogels seeded with CCs and FPSCs only. In contrast, a mixed co-culture of BMSCs and CCs led to increased proliferation and sGAG and collagen accumulation. Of note was the finding that a structured co-culture, at the appropriate cell density, led to greater sGAG accumulation than a mixed co-culture for both MSC sources. In conclusion, assembling MSCs onto CC-laden hydrogels dramatically enhances the development of the engineered tissue, with the superficial layer of progenitor cells driving CC proliferation and cartilage ECM production, mimicking certain aspects of developing cartilage. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

  7. Tuning the reactivity of Ru nanoparticles by defect engineering of the reduced graphene oxide support

    KAUST Repository

    Liu, Xin; Sui, Yanhui; Meng, Changgong; Han, Yu

    2014-01-01

    We systematically investigated the electronic structure of Ru nanoparticles supported on various local structures on reduced graphene oxide (rGO) by first-principles-based calculations. We showed that Ru nanoparticles prefer to nucleate

  8. Modeling and supporting the authoring process of multimedia simulation based educational software: a knowledge engineering approach

    NARCIS (Netherlands)

    Kuyper, Michiel; de Hoog, Robert; de Jong, Anthonius J.M.

    2001-01-01

    Traditionally, support for authoringeducational software focuses on the authoringprocess: the nature and sequence of theactivities that must be performed to deliverthe required product. As a consequence, themethods that are used tend to have a stronglinear flavor, which resembles the

  9. Support of scientific and technical progress in system of power engineering

    International Nuclear Information System (INIS)

    Khrapunov, V.V.

    1996-01-01

    The priority trends of the Republic Kazakhstan energetic policy are listed. These priorities define the principal trends in power engineering and coal industry. There are as following: creation and mastering new and modernizing existing technologies of mining, processing and combustion of fuel; electric and thermal power generation, maintaining significant reduce of a harmful exposure to environment, an economic efficiency at market economy conditions under high level of use of nature resources and raw materials; involving in power balance nontraditional and renewable energy sources, intensification works on energy conservation, reliability and vitality of power systems

  10. Fuzzy algorithmic and knowledge-based decision support in nuclear engineering

    International Nuclear Information System (INIS)

    Zimmermann, H. J.

    1996-01-01

    Fuzzy Set Theory was originally conceived as a means to model non- stochastic uncertainty. In the meantime it has matured to Fuzzy Technology and - together with Neural Nets and Genetic Algorithms - to Computational Intelligence. The goals have expanded considerably. In addition to uncertainty modeling, relaxation, compactification and meaning preserving reasoning have become major objectives. Nuclear engineering is one of the areas with a large potential for applications of Fuzzy Technologies, in which, however, the development is still at the beginning. This paper tries to survey applications and point to some potential applications which have not yet been realized

  11. Towards life-cycle awareness in decision support tools for engineering design

    OpenAIRE

    Nergård, Henrik; Sandberg, Marcus; Larsson, Tobias

    2009-01-01

    In this paper a decision support tool with the focus on how to generate and visualize decision base coupled to the business agreement is outlined and discussed. Decision support tools for the early design phases are few and especially tools that visualize the readiness level of activities throughout the product life-cycle. Aiming for the sustainable society there is an indication that business-to-business manufacturers move toward providing a function rather than selling off the hardware and ...

  12. Qualitative: Python Tool for MT Quality Estimation Supporting Server Mode and Hybrid MT

    Directory of Open Access Journals (Sweden)

    Avramidis Eleftherios

    2016-10-01

    Full Text Available We are presenting the development contributions of the last two years to our Python opensource Quality Estimation tool, a tool that can function in both experiment-mode and online web-service mode. The latest version provides a new MT interface, which communicates with SMT and rule-based translation engines and supports on-the-fly sentence selection. Additionally, we present an improved Machine Learning interface allowing more efficient communication with several state-of-the-art toolkits. Additions also include a more informative training process, a Python re-implementation of QuEst baseline features, a new LM toolkit integration, an additional PCFG parser and alignments of syntactic nodes.

  13. Accelerator production of tritium plant design and supporting engineering development and demonstration work

    International Nuclear Information System (INIS)

    Lisowski, P.W.

    1997-11-01

    Tritium is an isotope of hydrogen with a half life of 12.3 years. Because it is essential for US thermonuclear weapons to function, tritium must be periodically replenished. Since K reactor at Savannah River Site stopped operating in 1988, tritium has been recycled from dismantled nuclear weapons. This process is possible only as long as many weapons are being retired. Maintaining the stockpile at the level called for in the present Strategic Arms Reduction Treaty (START-I) will require the Department of Energy to have an operational tritium production capability in the 2005--2007 time frame. To make the required amount of tritium using an accelerator based system (APT), neutrons will be produced through high energy proton reactions with tungsten and lead. Those neutrons will be moderated and captured in 3 He to make tritium. The APT plant design will use a 1,700 MeV linear accelerator operated at 100 mA. In preparation for engineering design, starting in October 1997 and subsequent construction, a program of engineering development and demonstration is underway. That work includes assembly and testing of the first 20 MeV of the low energy plant linac at 100 mA, high-energy linac accelerating structure prototyping, radiofrequency power system improvements, neutronic efficiency measurements, and materials qualifications

  14. Treatability studies performed in support of an engineering evaluation/cost analysis

    International Nuclear Information System (INIS)

    Myers, J.M.; Mueller, J.P.; Sundquist, J.A.; Moore, G.W.

    1995-01-01

    The Southern Shipbuilding Corporation (SSC) site is located on 54 acres of wooded land adjacent to Bayou Bonfouca, approximately 1.8 miles downstream of the Bayou Bonfouca National Priorities List (NPL) Superfund site in Slidell, St. Tammany Parish, Louisiana. Two one-acre, impoundments on the SSC site were used to store wastes generated from vessel cleaning. Wastes stored in the impoundments are migrating into Bayou Bonfouca, which empties into Lake Pontchartrain. In addition, the impoundments are frequently invaded by flood waters. The US EPA Emergency Response Branch (EPA-ERB) performed a site investigation which indicated that the majority of the contamination is petroleum-related and that the compounds of concern are polycyclic aromatic hydrocarbons (PARs). The wastes are generally contained with the two impoundments and surrounding soils. As part of an Engineering Evaluation/Cost Basis (EE/CA) of potential response action alternatives, four treatability studies were performed. A thermal treatment (incineration) study was performed at the EPA's Incineration Research Facility (IRF). Biodegradation remedy selection feasibility assessment was conducted on-site. A remedy screening soil washing study was also performed by TAT. A solidification/stabilization (S/S) study was conducted through EPA's Risk Reduction Engineering Laboratory (RREL) to ascertain if the PAHs could be immobilized within a solid matrix. Experimental objectives, dead methodology and conclusions for these studies are presented as they relate to potential response actions being evaluated at the SSC site

  15. Basic data for surveillance test on core support graphite structures for the high temperature engineering test reactor (HTTR)

    International Nuclear Information System (INIS)

    Sumita, Junya; Shibata, Taiju; Kikuchi, Takayuki; Iyoku, Tatsuo; Fujimoto, Nozomu; Ishihara, Masahiro; Sawa, Kazuhiro

    2007-02-01

    Both of the visual inspection by a TV camera and the measurement of material properties by surveillance test on core support graphite structures are planned for the High Temperature Engineering Test Reactor (HTTR) to confirm their structural integrity and characteristics. The surveillance test is aimed to investigate the change of material properties by aging effects such as fast neutron irradiation and oxidation. The obtained data will be used not only for evaluating the structural integrity of the core support graphite structures of the HTTR but also for design of advanced Very High Temperature Reactor (VHTR) discussed at generation IV international forum. This report describes the initial material properties of surveillance specimens before installation and installed position of surveillance specimens in the HTTR. (author)

  16. Trends in biomedical engineering: focus on Patient Specific Modeling and Life Support Systems.

    Science.gov (United States)

    Dubini, Gabriele; Ambrosi, Davide; Bagnoli, Paola; Boschetti, Federica; Caiani, Enrico G; Chiastra, Claudio; Conti, Carlo A; Corsini, Chiara; Costantino, Maria Laura; D'Angelo, Carlo; Formaggia, Luca; Fumero, Roberto; Gastaldi, Dario; Migliavacca, Francesco; Morlacchi, Stefano; Nobile, Fabio; Pennati, Giancarlo; Petrini, Lorenza; Quarteroni, Alfio; Redaelli, Alberto; Stevanella, Marco; Veneziani, Alessandro; Vergara, Christian; Votta, Emiliano; Wu, Wei; Zunino, Paolo

    2011-01-01

    Over the last twenty years major advancements have taken place in the design of medical devices and personalized therapies. They have paralleled the impressive evolution of three-dimensional, non invasive, medical imaging techniques and have been continuously fuelled by increasing computing power and the emergence of novel and sophisticated software tools. This paper aims to showcase a number of major contributions to the advancements of modeling of surgical and interventional procedures and to the design of life support systems. The selected examples will span from pediatric cardiac surgery procedures to valve and ventricle repair techniques, from stent design and endovascular procedures to life support systems and innovative ventilation techniques.

  17. Biomedical engineering support. Annual progress report, August 15, 1974--August 14, 1975

    International Nuclear Information System (INIS)

    Kolff, W.J.; Smith, L.M.; Sandquist, G.M.

    1975-01-01

    The major responsibility of the Institute for Biomedical Engineering at the University of Utah under the ERDA Artificial Heart Program has been to provide in vitro and in vivo experimental data and evaluation of the anatomical fitting, accommodation, performance and adequacy of the artificial heart system and its components as they are developed in the ERDA Program and provided to the Institute for study. The Institute also has the responsibility of designing, constructing and testing the blood handling components of the Blood Pump and insuring reliability, durability and satisfactory performance of these system components. During the reporting period, nine total heart replacement experiments were performed in calves using the ERDA Blood Pump powered by an electric motor implanted in the abdomen. Results of the experiments are given. Ultimately the mechanical heart will be powered by a radioisotope heat source

  18. Recipe-Based Engineering and Operator Support for Flexible Configuration of High-Mix Assembly

    NARCIS (Netherlands)

    Verhoosel, J.P.C.; Bekkum, M.A. van

    2017-01-01

    Nowadays, manufacturers must be increasingly flexible to quickly produce a high mix of on-demand, customer-specific, low volume product types. This requires flexible assembly lines with operators that are well-supported in their constantly changing assembly task, while producing high-quality,

  19. A Customizable Language Learning Support System Using Ontology-Driven Engine

    Science.gov (United States)

    Wang, Jingyun; Mendori, Takahiko; Xiong, Juan

    2013-01-01

    This paper proposes a framework for web-based language learning support systems designed to provide customizable pedagogical procedures based on the analysis of characteristics of both learner and course. This framework employs a course-centered ontology and a teaching method ontology as the foundation for the student model, which includes learner…

  20. Supporting interoperability of collaborative networks through engineering of a service-based Mediation Information System (MISE 2.0)

    Science.gov (United States)

    Benaben, Frederick; Mu, Wenxin; Boissel-Dallier, Nicolas; Barthe-Delanoe, Anne-Marie; Zribi, Sarah; Pingaud, Herve

    2015-08-01

    The Mediation Information System Engineering project is currently finishing its second iteration (MISE 2.0). The main objective of this scientific project is to provide any emerging collaborative situation with methods and tools to deploy a Mediation Information System (MIS). MISE 2.0 aims at defining and designing a service-based platform, dedicated to initiating and supporting the interoperability of collaborative situations among potential partners. This MISE 2.0 platform implements a model-driven engineering approach to the design of a service-oriented MIS dedicated to supporting the collaborative situation. This approach is structured in three layers, each providing their own key innovative points: (i) the gathering of individual and collaborative knowledge to provide appropriate collaborative business behaviour (key point: knowledge management, including semantics, exploitation and capitalisation), (ii) deployment of a mediation information system able to computerise the previously deduced collaborative processes (key point: the automatic generation of collaborative workflows, including connection with existing devices or services) (iii) the management of the agility of the obtained collaborative network of organisations (key point: supervision of collaborative situations and relevant exploitation of the gathered data). MISE covers business issues (through BPM), technical issues (through an SOA) and agility issues of collaborative situations (through EDA).

  1. An engineering design study of the support platform assembly for the SSC SDC detector

    International Nuclear Information System (INIS)

    Krebs, H.J.; Western, J.L.; Wands, R.H.

    1993-04-01

    A large angular acceptance high energy physics particle detector is presently being designed by the Solenoidal Detector Collaboration for the purposes of doing high pt physics at the Superconducting Super Collider Laboratory. The support platform assembly is the structural device which transfers the 30,000 tonne gravitational load of the octagonally shaped muon barrel toroid and the other detector components to the foundation below. The detector components are very sensitive to differential deflection and rely on the barrel toroid and support platform for stability. The operational load path is provided by two pairs of inclined longitudinal plates resting at 67.5 degree on three pairs of plate girders that are positioned in-line in Z. The plate girders are held together laterally with 38 tie bars and supported vertically by the vertical adjustment system. The lateral stability of the inclined plates is provided by 22 stabilizer beams with cross bracing between each beam. The Z location of each split in the plate girder is coincident with the Z location of the gap in the calorimeter (4428 nun from the detector center.) The width of each split is 155 mm to allow installation of the alignment reference system. The collider beam line in the IR-8 underground experimental hall is oriented at a 2.16 mm/m slope from south to north as shown in Figure 2. The support is designed and installed to provide this slope at the top surface of the inclined plates. The assembled support rests on a ten foot thick steel reinforced 8000 psi concrete slab. The slab has a 2 mm differential deflection criteria under nominal gravitational loading

  2. Engineering testing and technology projects FY 1996 Site Support Program Plan, WBS 6.3.3 and 6.3.8. Revision 1

    International Nuclear Information System (INIS)

    Brown, L.C.

    1995-10-01

    The engineering laboratory services for development, assembly, testing, and evaluation to support the resolution of WHC, Hanford, and DOE complex wide engineering issues for 1996 are presented. Primary customers are: TWRS, spent nuclear fuels, transition projects, liquid effluent program, and other Hanford contractors and programs. Products and services provided include: fabrication and assembly facilities for prototype and test equipment, development testing, proof of principle testing, instrumentation testing, nondestructive examination application development and testing, prototype equipment design and assembly, chemical engineering unit operations testing, engineering test system disposal, and safety issue resolution

  3. Evaluation of engineering foods for closed Ecological Life Support System (CELSS)

    Science.gov (United States)

    Karel, M.

    1982-01-01

    A nutritionally adequate and acceptable diet was evaluated and developed. A design for a multipurpose food plant is discussed. The types and amounts of foods needed to be regenerated in a partially closed ecological life support system (PCELSS) were proposed. All steps of food processes to be utilized in the multipurpose food plant of PCELSS were also considered. Equipment specifications, simplification of the proposed processes, and food waste treatment were analyzed.

  4. Industrial Decision Support System with Assistance of 3D Game Engine

    OpenAIRE

    Zou, Ming

    2015-01-01

    Context. Industrial Decision Support System(DSS) traditionally relies on 2D approach to visualize the scenarios. For some abstract information, like chronological sequence of tasks or data trend, it provides a good visualization. For concrete information, such as location and spatial relationships, 2D visualizations are too abstract. Techniques from Game design, 3D modeling, virtual reality(VR) and animation provides many inspiration to develop a DSS tools for industrial applications. Objecti...

  5. Support of nuclear engineering education and research at the University of Michigan

    International Nuclear Information System (INIS)

    Martin, W.R.

    1993-03-01

    This report describes progress on four different projects in the fission reactor area that have been supported by the grant during the past year. These projects are: Accelerator transmutation of nuclear waste (Steve Pearson); neutronic analysis of the Ford Nuclear Reactor (Brent Renkema); developing Monte Carlo benchmarks for commercial LWR configurations (Jie Du); Monte Carlo depletion capability for massively parallel processors (Amit Majumdar); these tasks are briefly described and progress to date is presented

  6. Investment Decision Support for Engineering Projects Based on Risk Correlation Analysis

    Directory of Open Access Journals (Sweden)

    Yan Liu

    2012-01-01

    Full Text Available Investment decisions are usually made on the basis of the subjective judgments of experts subjected to the information gap during the preliminary stages of a project. As a consequence, a series of errors in risk prediction and/or decision-making will be generated leading to out of control investment and project failure. In this paper, the variable fuzzy set theory and intelligent algorithms integrated with case-based reasoning are presented. The proposed algorithm manages the numerous fuzzy concepts and variable factors of a project and also sets up the decision-making process in accordance with past cases and experiences. Furthermore, it decreases the calculation difficulty and reduces the decision-making reaction time. Three types of risk correlations combined with different characteristics of engineering projects are summarized, and each of these correlations is expounded at the project investment decision-making stage. Quantitative and qualitative change theories of variable fuzzy sets are also addressed for investment risk warning. The approach presented in this paper enables the risk analysis in a simple and intuitive manner and realizes the integration of objective and subjective risk assessments within the decision-makers' risk expectation.

  7. Estonian Language of Technology as a Factor Supporting the Evolution of Engineering Thinking

    Directory of Open Access Journals (Sweden)

    Mägi, Vahur

    2013-03-01

    Full Text Available Casual mention of teaching technology subjects in Estonian schools dates back several centuries. Navigation and construction were amongthe earliest professional skills that were taught. As both of them required mathematical thinking skills, teaching the subjects was usually accompanied by explaining the principles of mathematics. The first technology book in Estonian was published about two centuries ago and it dealed with geodesy. The earliest Estonian glossaries of technological terminology were published in the fields of physics and chemistry. The rise of Estonian as a language of higher education and science in the country came about in the 1920s and 1930s. Faculty members of the Tallinn School of Technology then published the first textbooks composed in the Estonian language for students of technology. The Estonian Society for Technology and the Estonian Association of Engineers became seriously involved in linguistic activities. Together with the Vocational Teachers’ Assembly of Tartu they published an illustrated technology glossary for machinery and tools terms. It was followed by a glossary of construction and building terms, compiled under the lead of the University of Technology. In addition, journals of technology introducedinnovations in the lexicon of technology to the general public. The postwar period in the development of the lexicon of technical terms was of little significance at first. A surge in language creativity could be detected in the 1960s, when terminology became a target of constantly growing attention to the development of technology lexicon. Series of technology glossaries were published. This tendency has continued to this day.

  8. To all of you who continue supporting Japanese Nuclear Power. A letter from nuclear engineer

    International Nuclear Information System (INIS)

    Sato, Satoshi

    2012-01-01

    Fukushima accident could not justify nuclear power and obliged nuclear engineers to accept public opinion such as 'nuclear power phase out' in 2030s. During the 'phase out' period, selected nuclear power plants would be restarted taking account of safety and accident effects with reinforced safety countermeasures against Fukushima accident, while shutdown reactor decommissioning with best technologies and intermediate storage of spent fuels before final disposal would be implemented. At the completion of 'phase out', Japanese nuclear power would end. However, renewable energy could not make such progress as expected and consumption of fossil energy would not decrease, which worsened environment and climate in Japan terribly and the public might think wrong decision of 'phase out' in 2012 and again request nuclear power. This nuclear power should be based on 'most advanced safety in the world', whose principle should be discussed and related R and D should be conducted beforehand. Such reactor would be developed to prevent core meltdown or assure containment integrity with 100% passive phenomena without any external power or human works against any cause's accidents, while spent fuels with not containing significant amount of long-life radioactive materials should be stored within artificial structures so as to reduce radioactivity level equivalent to outer environment. (T. Tanaka)

  9. Supporting STEM knowledge and skills in engineering education – PELARS project

    DEFF Research Database (Denmark)

    Cojocaru, Dorian; Friesel, Anna; Spikol, Daniel

    2016-01-01

    -based Experiential Learning Analytics Research And Support) provides technological tools and ICT-based methods for collecting activity data (moving image-based and embedded sensing) for learning analytics (data-mining and reasoning) of practice-based and experiential STEM. This data is used to create analytics...... through reasoning and feedback from input data. The project serves to better understand learners' knowledge in physical activities in laboratory and workshop environments, as well as informal learning scenarios. PELARS traces and helps assess learner progress through technology enhancement, in novel ways...

  10. A programmable rules engine to provide clinical decision support using HTML forms.

    Science.gov (United States)

    Heusinkveld, J; Geissbuhler, A; Sheshelidze, D; Miller, R

    1999-01-01

    The authors have developed a simple method for specifying rules to be applied to information on HTML forms. This approach allows clinical experts, who lack the programming expertise needed to write CGI scripts, to construct and maintain domain-specific knowledge and ordering capabilities within WizOrder, the order-entry and decision support system used at Vanderbilt Hospital. The clinical knowledge base maintainers use HTML editors to create forms and spreadsheet programs for rule entry. A test environment has been developed which uses Netscape to display forms; the production environment displays forms using an embedded browser.

  11. Labyrinth Seal Flutter Analysis and Test Validation in Support of Robust Rocket Engine Design

    Science.gov (United States)

    El-Aini, Yehia; Park, John; Frady, Greg; Nesman, Tom

    2010-01-01

    High energy-density turbomachines, like the SSME turbopumps, utilize labyrinth seals, also referred to as knife-edge seals, to control leakage flow. The pressure drop for such seals is order of magnitude higher than comparable jet engine seals. This is aggravated by the requirement of tight clearances resulting in possible unfavorable fluid-structure interaction of the seal system (seal flutter). To demonstrate these characteristics, a benchmark case of a High Pressure Oxygen Turbopump (HPOTP) outlet Labyrinth seal was studied in detail. First, an analytical assessment of the seal stability was conducted using a Pratt & Whitney legacy seal flutter code. Sensitivity parameters including pressure drop, rotor-to-stator running clearances and cavity volumes were examined and modeling strategies established. Second, a concurrent experimental investigation was undertaken to validate the stability of the seal at the equivalent operating conditions of the pump. Actual pump hardware was used to construct the test rig, also referred to as the (Flutter Rig). The flutter rig did not include rotational effects or temperature. However, the use of Hydrogen gas at high inlet pressure provided good representation of the critical parameters affecting flutter especially the speed of sound. The flutter code predictions showed consistent trends in good agreement with the experimental data. The rig test program produced a stability threshold empirical parameter that separated operation with and without flutter. This empirical parameter was used to establish the seal build clearances to avoid flutter while providing the required cooling flow metering. The calibrated flutter code along with the empirical flutter parameter was used to redesign the baseline seal resulting in a flutter-free robust configuration. Provisions for incorporation of mechanical damping devices were introduced in the redesigned seal to ensure added robustness

  12. Advancing cognitive engineering methods to support user interface design for electronic health records.

    Science.gov (United States)

    Thyvalikakath, Thankam P; Dziabiak, Michael P; Johnson, Raymond; Torres-Urquidy, Miguel Humberto; Acharya, Amit; Yabes, Jonathan; Schleyer, Titus K

    2014-04-01

    Despite many decades of research on the effective development of clinical systems in medicine, the adoption of health information technology to improve patient care continues to be slow, especially in ambulatory settings. This applies to dentistry as well, a primary care discipline with approximately 137,000 practitioners in the United States. A critical reason for slow adoption is the poor usability of clinical systems, which makes it difficult for providers to navigate through the information and obtain an integrated view of patient data. In this study, we documented the cognitive processes and information management strategies used by dentists during a typical patient examination. The results will inform the design of a novel electronic dental record interface. We conducted a cognitive task analysis (CTA) study to observe ten general dentists (five general dentists and five general dental faculty members, each with more than two years of clinical experience) examining three simulated patient cases using a think-aloud protocol. Dentists first reviewed the patient's demographics, chief complaint, medical history and dental history to determine the general status of the patient. Subsequently, they proceeded to examine the patient's intraoral status using radiographs, intraoral images, hard tissue and periodontal tissue information. The results also identified dentists' patterns of navigation through patient's information and additional information needs during a typical clinician-patient encounter. This study reinforced the significance of applying cognitive engineering methods to inform the design of a clinical system. Second, applying CTA to a scenario closely simulating an actual patient encounter helped with capturing participants' knowledge states and decision-making when diagnosing and treating a patient. The resultant knowledge of dentists' patterns of information retrieval and review will significantly contribute to designing flexible and task

  13. Engineer Company Force Structure Force Modularization in Support of Decisive Action. Does the Corps of Engineers Need to Re-Structure Engineer Construction Companies Again in order to Support Decisive Actions?

    Science.gov (United States)

    2012-05-16

    Regional Command RCP Route Clearance Platoon RSOI Reception, Staging, Onward Movement, Integration SBCT Stryker Brigade Combat Team TOE Table of...Point (ASPs), and field hospital platforms; prepare river crossing sites; and support port repair due to Hydraulic Excavator (HYEX), provides force...platforms, FARPS, supply routes, roads, control points, fire bases, tank ditches, ASPs, and field hospital platforms; prepare river crossing sites; and

  14. Dismantling of civilian nuclear powered fleet technical support vessels. engineering solutions - 59386

    International Nuclear Information System (INIS)

    Kulikov, Konstantin N.; Nizamutdinov, Rinat A.; Abramov, Andrey N.

    2012-01-01

    At the present time six nuclear technical support vessels are operated and maintained by Atomflot. Two of them (Volodarsky FTB (floating technical base) and Lepse FTB) were taken out of service for decommissioning and are stored afloat. One more vessel Lotta FTB should be decommissioned during next two years. The nuclear technological support ships carrying spent nuclear fuel (SNF), liquid and solid radioactive wastes (LRW and SRW) appear to be a possible radiation contamination of Murmansk region and Kola Bay because the Ship long-term storage afloat has the negative effect on hull's structures technical condition. As a result of this in the context of the Federal Program 'Nuclear and Radiation Safety' (2008-2015) NIPTB Onega OAO was engaged by state corporation Rosatom to develop the dismantling procedure for Volodarsky FTB and Lotta FTB. Before developing of nuclear technological support ships decommissioning projects the technical and economic assessment of decommissioning/dismantling was carried out. The following options were examined: - formation of module as one-piece Ship's hull for long-term storage at Saida Bay; - formation of separated modules for long-term storage at Saida Bay; - complete dismantling of hull's structures, systems and equipment with packing all generated SRW into certified long-term storage containers. This paper contains description of options, research procedure, comparative analysis of options of decommissioning and dismantling (D and D) of nuclear technological support ships and its difference with dismantling of nuclear submarine. On the basis of the technical and economic assessment of FTB D and D options the least expensive on the first D and D stage and the least duration option is the option 1 (Formation of module as one-piece Ship's hull for long-term storage at Saida Bay). By the implementation of the given option there will be the need of large areas for modules storage at Saida Bay. It was not considered while working out

  15. Supporting Students with Disabilities Entering the Science, Technology, Engineering, and Mathematics Field Disciplines

    Science.gov (United States)

    Dishauzi, Karen M.

    Extensive research exists on female, African American, and Hispanic students pursuing Science, Technology, Engineering and Mathematics (STEM) field disciplines. However, little research evaluates students with disabilities and career decision-making relating to STEM field disciplines. This study explored the career decision-making experiences and self-efficacy for students with disabilities. The purpose of this research study was to document experiences and perceptions of students with disabilities who pursue, and may consider pursuing, careers in the STEM field disciplines by exploring the career decision-making self-efficacy of students with disabilities. This study documented the level of influence that the students with disabilities had or may not have had encountered from parents, friends, advisors, counselors, and instructors as they managed their decision-making choice relating to their academic major/career in the STEM or non-STEM field disciplines. A total of 85 respondents of approximately 340 students with disabilities at one Midwestern public university completed a quantitatively designed survey instrument. The Career Decision-Making Self-Efficacy Scale-Short Form by Betz and Hackett was the instrument used, and additional questions were included in the survey. Data analysis included descriptive statistics and analysis of variance. Based upon the results, college students with disabilities are not currently being influenced by individuals and groups of individuals to pursue the STEM field disciplines. This is a cohort of individuals who can be marketed to increase enrollment in STEM programs at academic institutions. This research further found that gender differences at the institution under study did not affect the career decision-making self-efficacy scores. The men did not score any higher in confidence in career decision-making than the women. Disability type did not significantly affect the relationship between the Career Decision-Making Self

  16. Generating Southern Africa Precipitation Forecast Using the FEWS Engine, a New Application for the Google Earth Engine

    Science.gov (United States)

    Landsfeld, M. F.; Hegewisch, K.; Daudert, B.; Morton, C.; Husak, G. J.; Friedrichs, M.; Funk, C. C.; Huntington, J. L.; Abatzoglou, J. T.; Verdin, J. P.

    2016-12-01

    The Famine Early Warning Systems Network (FEWS NET) focuses on food insecurity in developing nations and provides objective, evidence-based analysis to help government decision-makers and relief agencies plan for and respond to humanitarian emergencies. The network of FEWS NET analysts and scientists require flexible, interactive tools to aid in their monitoring and research efforts. Because they often work in bandwidth-limited regions, lightweight Internet tools and services that bypass the need for downloading massive datasets are preferred for their work. To support food security analysis FEWS NET developed a custom interface for the Google Earth Engine (GEE). GEE is a platform developed by Google to support scientific analysis of environmental data in their cloud computing environment. This platform allows scientists and independent researchers to mine massive collections of environmental data, leveraging Google's vast computational resources for purposes of detecting changes and monitoring the Earth's surface and climate. GEE hosts an enormous amount of satellite imagery and climate archives, one of which is the Climate Hazards Group Infrared Precipitation with Stations dataset (CHIRPS). CHIRPS precipitation dataset is a key input for FEWS NET monitoring and forecasting efforts. In this talk we introduce the FEWS Engine interface. We present an application that highlights the utility of FEWS Engine for forecasting the upcoming seasonal precipitation of southern Africa. Specifically, the current state of ENSO is assessed and used to identify similar historical seasons. The FEWS Engine compositing tool is used to examine rainfall and other environmental data for these analog seasons. The application illustrates the unique benefits of using FEWS Engine for on-the-fly food security scenario development.

  17. The effectiveness of insurer-supported safety and health engineering controls in reducing workers' compensation claims and costs.

    Science.gov (United States)

    Wurzelbacher, Steven J; Bertke, Stephen J; Lampl, Michael P; Bushnell, P Timothy; Meyers, Alysha R; Robins, David C; Al-Tarawneh, Ibraheem S

    2014-12-01

    This study evaluated the effectiveness of a program in which a workers' compensation (WC) insurer provided matching funds to insured employers to implement safety/health engineering controls. Pre- and post-intervention WC metrics were compiled for the employees designated as affected by the interventions within 468 employers for interventions occurring from 2003 to 2009. Poisson, two-part, and linear regression models with repeated measures were used to evaluate differences in pre- and post-data, controlling for time trends independent of the interventions. For affected employees, total WC claim frequency rates (both medical-only and lost-time claims) decreased 66%, lost-time WC claim frequency rates decreased 78%, WC paid cost per employee decreased 81%, and WC geometric mean paid claim cost decreased 30% post-intervention. Reductions varied by employer size, specific industry, and intervention type. The insurer-supported safety/health engineering control program was effective in reducing WC claims and costs for affected employees. © 2014 Wiley Periodicals, Inc.

  18. Engineering cartilage substitute with a specific size and shape using porous high-density polyethylene (HDPE) as internal support.

    Science.gov (United States)

    Wu, Yujia; Zhu, Lie; Jiang, Hua; Liu, Wei; Liu, Yu; Cao, Yilin; Zhou, Guangdong

    2010-04-01

    Despite the great advances in cartilage engineering, constructing cartilage of large sizes and appropriate shapes remains a great challenge, owing to limits in thickness of regenerated cartilage and to inferior mechanical properties of scaffolds. This study introduces a pre-shaped polyglycolic acid (PGA)-coated porous high-density polyethylene (HDPE) scaffold to overcome these challenges. HDPE was carved into cylindrical rods and wrapped around by PGA fibres to form PGA-HDPE scaffolds. Porcine chondrocytes were seeded into the scaffolds and the constructs were cultured in vitro for 2 weeks before subcutaneous implantation into nude mice. Scaffolds made purely of PGA with the same size and shape were used as a control. After 8 weeks of implantation, the construct formed cartilage-like tissue and retained its pre-designed shape and size. In addition, the regenerated cartilage grew and completely surrounded the HDPE core, which made the entire cartilage substitute biocompatible to its implanted environment as native cartilage similarly does. By contrast, the shape and size of the constructs in the control group seriously deformed and obvious hollow cavity and necrotic tissue were observed in the inner region. These results demonstrate that the use of HDPE as the internal support of a biodegradable scaffold has the potential to circumvent the problems of limitations in size and shape, with promising implications for the development of engineered cartilage appropriate for clinical applications. Copyright 2009 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

  19. How engineering data management and system support the main process[-oriented] functions of a large-scale project

    CERN Document Server

    Hameri, A P

    1999-01-01

    By dividing the development process into successive functional operations, this paper studies the benefits of establishing configuration management procedures and of using an engineering data management systems (EDMS) in order to execute the tasks. The underlying environment is that of CERN and the ongoing, a decade long, Large Hadron Collider (LHC)-project. By identifying the main functional groups who will use the EDMS the paper outlines the basic motivations and services provided by such a system to each process function. The implications of strict configuration management on the daily operation of each functional user group are also discussed. The main argument of the paper is that each and every user of the EDMS must act in compliance with the configuration management procedures to guarantee the overall benefits from the system. The pilot EDMS being developed at CERN, which serves as a test-bed to discover the real functional needs of the organisation of an EDMS supports the conclusions. The preliminary ...

  20. Systems engineering aspects of a preliminary conceptual design of the space station environmental control and life support system

    Science.gov (United States)

    Lin, C. H.; Meyer, M. S.

    1983-01-01

    The systems engineering aspects of developing a conceptual design of the Space Station Environmental Control and Life Support System (ECLSS) are discussed. Topics covered include defining system requirements and groundrules for approach, formulating possible cycle closure options, and establishing a system-level mass balance on the essential materials processed in oxygen and water cycles. Consideration is also given to the performance of a system trade-off study to determine the best degree of cycle closure for the ECLSS, and the construction of a conceptual design of the ECLSS with subsystem performance specifications and candidate concepts. For the optimum balance between development costs, technological risks, and resupply penalties, a partially closed cycle ECLSS option is suggested.

  1. Studies performed in support of the proposed revision of engineering design aspects of 10CFR100, Appendix A

    International Nuclear Information System (INIS)

    Witte, M.; Prassinos, P.; Kenneally, R.; Chokshi, N.

    1991-01-01

    Part 100 of Title 10 of the Code of Federal Regulations (10CFR100) describes criteria which guide the commission in its evaluation of the suitability of proposed sites for nuclear power plants. Appendix A of this part describes seismic and geologic siting criteria for nuclear power plants. Some engineering design aspects of nuclear power plants are also briefly addressed in Appendix A. These include: definition of the operating basis earthquake (OBE) and the safe shutdown earthquake (SSE), definitions of safety related structures, systems and components, ratio of OBE to SSE, identification of acceptable analytical methods, and definition of vibratory ground motion. One of the interpretations of the regulations on the selection of the two earthquake design levels, the SSE and OBE, was that the SSE would control the design of all safety related systems while the OBE would be applied to the remaining systems required for continued power operation. In practice, however, with the load factors, damping, and service limits, the OBE, rather than the SSE, has controlled the design for some systems. The work in progress at Lawrence Livermore National Laboratory and at the Nuclear Regulatory Commission will develop the technical basis to support engineering related changes to Appendix A. Included in this effort are the following: investigation of the impact of removing the OBE from design considerations with regard to safety options and review of possible strategies regarding the definition and requirements of the OBE for future reactors. This paper reports on the status and results of studies performed to date in support of this project. These include a study to identify components that are important to plant safety and also are affected by OBE designs; a study to evaluate the impact on ASME BPVC Section 3 Division 1 of eliminating the OBE; and a study to evaluate the impact on design margins if the OBE is eliminated from design

  2. Engineering Encounters: Reverse Engineering

    Science.gov (United States)

    McGowan, Veronica Cassone; Ventura, Marcia; Bell, Philip

    2017-01-01

    This column presents ideas and techniques to enhance your science teaching. This month's issue shares information on how students' everyday experiences can support science learning through engineering design. In this article, the authors outline a reverse-engineering model of instruction and describe one example of how it looked in our fifth-grade…

  3. A Powerful, Cost Effective, Web Based Engineering Solution Supporting Conjunction Detection and Visual Analysis

    Science.gov (United States)

    Novak, Daniel M.; Biamonti, Davide; Gross, Jeremy; Milnes, Martin

    2013-08-01

    An innovative and visually appealing tool is presented for efficient all-vs-all conjunction analysis on a large catalogue of objects. The conjunction detection uses a nearest neighbour search algorithm, based on spatial binning and identification of pairs of objects in adjacent bins. This results in the fastest all vs all filtering the authors are aware of. The tool is constructed on a server-client architecture, where the server broadcasts to the client the conjunction data and ephemerides, while the client supports the user interface through a modern browser, without plug-in. In order to make the tool flexible and maintainable, Java software technologies were used on the server side, including Spring, Camel, ActiveMQ and CometD. The user interface and visualisation are based on the latest web technologies: HTML5, WebGL, THREE.js. Importance has been given on the ergonomics and visual appeal of the software. In fact certain design concepts have been borrowed from the gaming industry.

  4. Feature engineering and a proposed decision-support system for systematic reviewers of medical evidence.

    Directory of Open Access Journals (Sweden)

    Tanja Bekhuis

    Full Text Available Evidence-based medicine depends on the timely synthesis of research findings. An important source of synthesized evidence resides in systematic reviews. However, a bottleneck in review production involves dual screening of citations with titles and abstracts to find eligible studies. For this research, we tested the effect of various kinds of textual information (features on performance of a machine learning classifier. Based on our findings, we propose an automated system to reduce screeing burden, as well as offer quality assurance.We built a database of citations from 5 systematic reviews that varied with respect to domain, topic, and sponsor. Consensus judgments regarding eligibility were inferred from published reports. We extracted 5 feature sets from citations: alphabetic, alphanumeric(+, indexing, features mapped to concepts in systematic reviews, and topic models. To simulate a two-person team, we divided the data into random halves. We optimized the parameters of a Bayesian classifier, then trained and tested models on alternate data halves. Overall, we conducted 50 independent tests.All tests of summary performance (mean F3 surpassed the corresponding baseline, P<0.0001. The ranks for mean F3, precision, and classification error were statistically different across feature sets averaged over reviews; P-values for Friedman's test were .045, .002, and .002, respectively. Differences in ranks for mean recall were not statistically significant. Alphanumeric(+ features were associated with best performance; mean reduction in screening burden for this feature type ranged from 88% to 98% for the second pass through citations and from 38% to 48% overall.A computer-assisted, decision support system based on our methods could substantially reduce the burden of screening citations for systematic review teams and solo reviewers. Additionally, such a system could deliver quality assurance both by confirming concordant decisions and by naming

  5. Academic Support Program in the Faculty of Agricultural and Forestry Engineering of the University of Cordoba (Spain)

    Science.gov (United States)

    Castro, Sergio; Navarro, Rafael M.; Camacho, Emilio; Gallardo, Rosa; García-Ferrer, Alfonso; Pérez-Marín, M. Dolores; Peña, Adolfo; Taguas, Encarnación V.

    2014-05-01

    The incorporation of new students to undergraduate degrees is performed in different stages through a long, sequential enrollment process. The student integration to the new context of higher education including group work and new teaching methodologies lead to notable adaptation difficulties to this new educational environment. In fact, the highest rate of student failure in the Bachelor degree usually happens during the first courses. The Unit of Quality Evaluation/Monitoring of School of Agricultural and Forest Engineering (ETSIAM) has detected that these failure rates at first and second degree course may be reduced through the involvement of students in a support learning process, by increasing their skills and motivation as well as the contact with the University environment in the context of their future professional horizon. In order to establish a program of this type, it has been launched an Academic Support Program (ASP) at the ETSIAM. This program aims to achieve and reinforce the basic academic and personal skills/competences require by the Bologna's process (BC) and specific competences of the engineers on the area of Agriculture and Forestry in the European context. The ASP includes diferent bloks of seminars, lectures, collaborative work and discussion groups among students, professionals, professors and researchers and it has been designed based on these competences and tranversal contents in both degrees. These activities are planned in a common time for both degrees, out of teaching classes. In addition, a virtual space in Moodle has been created for discussion forums and preparation activities. Additional information about schedules, speakers and companies, presentations and other material are also provided. In the preliminary implementation of the ASP, we will present the results corresponding to the first year of this academic support program. We have conducted a survey among the students in order to have a first feedback about the impact of

  6. Cuckoo Search Algorithm with Lévy Flights for Global-Support Parametric Surface Approximation in Reverse Engineering

    Directory of Open Access Journals (Sweden)

    Andrés Iglesias

    2018-03-01

    Full Text Available This paper concerns several important topics of the Symmetry journal, namely, computer-aided design, computational geometry, computer graphics, visualization, and pattern recognition. We also take advantage of the symmetric structure of the tensor-product surfaces, where the parametric variables u and v play a symmetric role in shape reconstruction. In this paper we address the general problem of global-support parametric surface approximation from clouds of data points for reverse engineering applications. Given a set of measured data points, the approximation is formulated as a nonlinear continuous least-squares optimization problem. Then, a recent metaheuristics called Cuckoo Search Algorithm (CSA is applied to compute all relevant free variables of this minimization problem (namely, the data parameters and the surface poles. The method includes the iterative generation of new solutions by using the Lévy flights to promote the diversity of solutions and prevent stagnation. A critical advantage of this method is its simplicity: the CSA requires only two parameters, many fewer than any other metaheuristic approach, so the parameter tuning becomes a very easy task. The method is also simple to understand and easy to implement. Our approach has been applied to a benchmark of three illustrative sets of noisy data points corresponding to surfaces exhibiting several challenging features. Our experimental results show that the method performs very well even for the cases of noisy and unorganized data points. Therefore, the method can be directly used for real-world applications for reverse engineering without further pre/post-processing. Comparative work with the most classical mathematical techniques for this problem as well as a recent modification of the CSA called Improved CSA (ICSA is also reported. Two nonparametric statistical tests show that our method outperforms the classical mathematical techniques and provides equivalent results to ICSA

  7. Earthquake Engineering Support

    Science.gov (United States)

    1999-11-01

    recovered from eql 3c 7 525 49% loose 79% dense 2 5/5/98 1 3 Nevada sand, ESB #2 3d 11 525 54% loose 80% dense 2 3/9/98 2.5 4 Nevada sand, ESB #2 3e...The pore pressure transducers used in the experiments were manufactured by Druck , and are widely used in centrifuge modelling. Typical

  8. Platelet lysate 3D scaffold supports mesenchymal stem cell chondrogenesis: an improved approach in cartilage tissue engineering.

    Science.gov (United States)

    Moroz, Andrei; Bittencourt, Renata Aparecida Camargo; Almeida, Renan Padron; Felisbino, Sérgio Luis; Deffune, Elenice

    2013-01-01

    Articular lesions are still a major challenge in orthopedics because of cartilage's poor healing properties. A major improvement in therapeutics was the development of autologous chondrocytes implantation (ACI), a biotechnology-derived technique that delivers healthy autologous chondrocytes after in vitro expansion. To obtain cartilage-like tissue, 3D scaffolds are essential to maintain chondrocyte differentiated status. Currently, bioactive 3D scaffolds are promising as they can deliver growth factors, cytokines, and hormones to the cells, giving them a boost to attach, proliferate, induce protein synthesis, and differentiate. Using mesenchymal stem cells (MSCs) differentiated into chondrocytes, one can avoid cartilage harvesting. Thus, we investigated the potential use of a platelet-lysate-based 3D bioactive scaffold to support chondrogenic differentiation and maintenance of MSCs. The MSCs from adult rabbit bone marrow (n = 5) were cultivated and characterized using three antibodies by flow cytometry. MSCs (1 × 10(5)) were than encapsulated inside 60 µl of a rabbit platelet-lysate clot scaffold and maintained in Dulbecco's Modified Eagle Medium Nutrient Mixture F-12 supplemented with chondrogenic inductors. After 21 days, the MSCs-seeded scaffolds were processed for histological analysis and stained with toluidine blue. This scaffold was able to maintain round-shaped cells, typical chondrocyte metachromatic extracellular matrix deposition, and isogenous group formation. Cells accumulated inside lacunae and cytoplasm lipid droplets were other observed typical chondrocyte features. In conclusion, the usage of a platelet-lysate bioactive scaffold, associated with a suitable chondrogenic culture medium, supports MSCs chondrogenesis. As such, it offers an alternative tool for cartilage engineering research and ACI.

  9. The Generalized Support Software (GSS) Domain Engineering Process: An Object-Oriented Implementation and Reuse Success at Goddard Space Flight Center

    Science.gov (United States)

    Condon, Steven; Hendrick, Robert; Stark, Michael E.; Steger, Warren

    1997-01-01

    The Flight Dynamics Division (FDD) of NASA's Goddard Space Flight Center (GSFC) recently embarked on a far-reaching revision of its process for developing and maintaining satellite support software. The new process relies on an object-oriented software development method supported by a domain specific library of generalized components. This Generalized Support Software (GSS) Domain Engineering Process is currently in use at the NASA GSFC Software Engineering Laboratory (SEL). The key facets of the GSS process are (1) an architecture for rapid deployment of FDD applications, (2) a reuse asset library for FDD classes, and (3) a paradigm shift from developing software to configuring software for mission support. This paper describes the GSS architecture and process, results of fielding the first applications, lessons learned, and future directions

  10. Peer-Assisted Learning Programme: Supporting Students in High-Risk Subjects at the Mechanical Engineering Department at Walter Sisulu University

    Science.gov (United States)

    Makola, Qonda

    2017-01-01

    The majority of the students who enroll at the Walter Sisulu University (WSU) in South Africa are not equipped with the necessary academic/learning skills to cope with the university environment, especially in Mechanical Engineering. The Department of Higher Education and Training (2013, p. 17), further states that "students' support is…

  11. Engineering Review Information System

    Science.gov (United States)

    Grems, III, Edward G. (Inventor); Henze, James E. (Inventor); Bixby, Jonathan A. (Inventor); Roberts, Mark (Inventor); Mann, Thomas (Inventor)

    2015-01-01

    A disciplinal engineering review computer information system and method by defining a database of disciplinal engineering review process entities for an enterprise engineering program, opening a computer supported engineering item based upon the defined disciplinal engineering review process entities, managing a review of the opened engineering item according to the defined disciplinal engineering review process entities, and closing the opened engineering item according to the opened engineering item review.

  12. Information Engineering and Workflow Design in a Clinical Decision Support System for Colorectal Cancer Screening in Iran.

    Science.gov (United States)

    Maserat, Elham; Seied Farajollah, Seiede Sedigheh; Safdari, Reza; Ghazisaeedi, Marjan; Aghdaei, Hamid Asadzadeh; Zali, Mohammad Reza

    2015-01-01

    Colorectal cancer is a major cause of morbidity and mortality throughout the world. Colorectal cancer screening is an optimal way for reducing of morbidity and mortality and a clinical decision support system (CDSS) plays an important role in predicting success of screening processes. DSS is a computer-based information system that improves the delivery of preventive care services. The aim of this article was to detail engineering of information requirements and work flow design of CDSS for a colorectal cancer screening program. In the first stage a screening minimum data set was determined. Developed and developing countries were analyzed for identifying this data set. Then information deficiencies and gaps were determined by check list. The second stage was a qualitative survey with a semi-structured interview as the study tool. A total of 15 users and stakeholders' perspectives about workflow of CDSS were studied. Finally workflow of DSS of control program was designed by standard clinical practice guidelines and perspectives. Screening minimum data set of national colorectal cancer screening program was defined in five sections, including colonoscopy data set, surgery, pathology, genetics and pedigree data set. Deficiencies and information gaps were analyzed. Then we designed a work process standard of screening. Finally workflow of DSS and entry stage were determined. A CDSS facilitates complex decision making for screening and has key roles in designing optimal interactions between colonoscopy, pathology and laboratory departments. Also workflow analysis is useful to identify data reconciliation strategies to address documentation gaps. Following recommendations of CDSS should improve quality of colorectal cancer screening.

  13. Increasing public support for food-industry related, obesity prevention policies: The role of a taste-engineering frame and contextualized values.

    Science.gov (United States)

    Ortiz, Selena E; Zimmerman, Frederick J; Adler, Gary J

    2016-05-01

    Support for policies to combat obesity is often undermined by a public sense that obesity is largely a matter of personal responsibility. Industry rhetoric is a major contributor to this perception, as the soda/fast food/big food companies emphasize choice and individual agency in their efforts to neutralize policies that are burdensome. Yet obesity experts recognize that environmental forces play a major role in obesity. We investigate whether exposure to a taste-engineering frame increases support for food and beverage policies that address obesity. A taste-engineering frame details strategies used by the food industry to engineer preferences and increase the over-consumption of processed foods and sugary beverages. We also examine the effects of exposure to two contextualized values that have recently been promoted in expert discourse-consumer knowledge and consumer safety - on public support of policies. Our research shows how causal frames and contextualized values may effectively produce support for new obesity policies. We use an online survey experiment to test the effects of exposure to a taste-engineering frame (TEF), the value of consumer knowledge (CK), or the value of consumer safety (CS), on level of support for a range of policies. A random sample of adults, age 18 + living in the United States was included in the study (N = 2580). Ordered logistic regression was used to measure the effects of treatment exposure. The primary outcome was level-of-support for four (4) food-industry related, obesity prevention policies (aka food and beverage policies): 1) require food-manufacturers to disclose the amount of additives in food products on food packaging; 2) require food-manufacturers to advertise food products in accordance with their actual nutritional value; 3) prohibit all high-fat, high-sugar food advertising on television programming watched primarily by children; and 4) increase healthy food availability in work sites, schools, and hospitals

  14. Mobile membrane introduction tandem mass spectrometry for on-the-fly measurements and adaptive sampling of VOCs around oil and gas projects in Alberta, Canada

    Science.gov (United States)

    Krogh, E.; Gill, C.; Bell, R.; Davey, N.; Martinsen, M.; Thompson, A.; Simpson, I. J.; Blake, D. R.

    2012-12-01

    The release of hydrocarbons into the environment can have significant environmental and economic consequences. The evolution of smaller, more portable mass spectrometers to the field can provide spatially and temporally resolved information for rapid detection, adaptive sampling and decision support. We have deployed a mobile platform membrane introduction mass spectrometer (MIMS) for the in-field simultaneous measurement of volatile and semi-volatile organic compounds. In this work, we report instrument and data handling advances that produce geographically referenced data in real-time and preliminary data where these improvements have been combined with high precision ultra-trace VOCs analysis to adaptively sample air plumes near oil and gas operations in Alberta, Canada. We have modified a commercially available ion-trap mass spectrometer (Griffin ICX 400) with an in-house temperature controlled capillary hollow fibre polydimethylsiloxane (PDMS) polymer membrane interface and in-line permeation tube flow cell for a continuously infused internal standard. The system is powered by 24 VDC for remote operations in a moving vehicle. Software modifications include the ability to run continuous, interlaced tandem mass spectrometry (MS/MS) experiments for multiple contaminants/internal standards. All data are time and location stamped with on-board GPS and meteorological data to facilitate spatial and temporal data mapping. Tandem MS/MS scans were employed to simultaneously monitor ten volatile and semi-volatile analytes, including benzene, toluene, ethylbenzene and xylene (BTEX), reduced sulfur compounds, halogenated organics and naphthalene. Quantification was achieved by calibrating against a continuously infused deuterated internal standard (toluene-d8). Time referenced MS/MS data were correlated with positional data and processed using Labview and Matlab to produce calibrated, geographical Google Earth data-visualizations that enable adaptive sampling protocols

  15. A Hybrid Approach to Cognitive Engineering: Supporting Development of a Revolutionary Warfighter-Centered Command and Control System

    National Research Council Canada - National Science Library

    Ockerman, Jennifer; McKneely, Jennifer A; Koterba, Nathan

    2005-01-01

    ...) for the requirements analysis and design of revolutionary command and control systems and domains. This hybrid approach uses knowledge elicitation and representation techniques from several current cognitive engineering methodologies...

  16. A Clinical Decision Support Engine Based on a National Medication Repository for the Detection of Potential Duplicate Medications: Design and Evaluation.

    Science.gov (United States)

    Yang, Cheng-Yi; Lo, Yu-Sheng; Chen, Ray-Jade; Liu, Chien-Tsai

    2018-01-19

    A computerized physician order entry (CPOE) system combined with a clinical decision support system can reduce duplication of medications and thus adverse drug reactions. However, without infrastructure that supports patients' integrated medication history across health care facilities nationwide, duplication of medication can still occur. In Taiwan, the National Health Insurance Administration has implemented a national medication repository and Web-based query system known as the PharmaCloud, which allows physicians to access their patients' medication records prescribed by different health care facilities across Taiwan. This study aimed to develop a scalable, flexible, and thematic design-based clinical decision support (CDS) engine, which integrates a national medication repository to support CPOE systems in the detection of potential duplication of medication across health care facilities, as well as to analyze its impact on clinical encounters. A CDS engine was developed that can download patients' up-to-date medication history from the PharmaCloud and support a CPOE system in the detection of potential duplicate medications. When prescribing a medication order using the CPOE system, a physician receives an alert if there is a potential duplicate medication. To investigate the impact of the CDS engine on clinical encounters in outpatient services, a clinical encounter log was created to collect information about time, prescribed drugs, and physicians' responses to handling the alerts for each encounter. The CDS engine was installed in a teaching affiliate hospital, and the clinical encounter log collected information for 3 months, during which a total of 178,300 prescriptions were prescribed in the outpatient departments. In all, 43,844/178,300 (24.59%) patients signed the PharmaCloud consent form allowing their physicians to access their medication history in the PharmaCloud. The rate of duplicate medication was 5.83% (1843/31,614) of prescriptions. When

  17. Supporting inter-topic entity search for biomedical Linked Data based on heterogeneous relationships.

    Science.gov (United States)

    Zong, Nansu; Lee, Sungin; Ahn, Jinhyun; Kim, Hong-Gee

    2017-08-01

    The keyword-based entity search restricts search space based on the preference of search. When given keywords and preferences are not related to the same biomedical topic, existing biomedical Linked Data search engines fail to deliver satisfactory results. This research aims to tackle this issue by supporting an inter-topic search-improving search with inputs, keywords and preferences, under different topics. This study developed an effective algorithm in which the relations between biomedical entities were used in tandem with a keyword-based entity search, Siren. The algorithm, PERank, which is an adaptation of Personalized PageRank (PPR), uses a pair of input: (1) search preferences, and (2) entities from a keyword-based entity search with a keyword query, to formalize the search results on-the-fly based on the index of the precomputed Individual Personalized PageRank Vectors (IPPVs). Our experiments were performed over ten linked life datasets for two query sets, one with keyword-preference topic correspondence (intra-topic search), and the other without (inter-topic search). The experiments showed that the proposed method achieved better search results, for example a 14% increase in precision for the inter-topic search than the baseline keyword-based search engine. The proposed method improved the keyword-based biomedical entity search by supporting the inter-topic search without affecting the intra-topic search based on the relations between different entities. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Support vector machine-based exergetic modelling of a DI diesel engine running on biodiesel–diesel blends containing expanded polystyrene

    International Nuclear Information System (INIS)

    Shamshirband, Shahaboddin; Tabatabaei, Meisam; Aghbashlo, Mortaza; Yee, Por Lip; Petković, Dalibor

    2016-01-01

    Highlights: • SVM-based thermodynamic modelling of a DI diesel engine working with diesel/biodiesel blends containing EPS. • Comparison of SVM-WT, SVM-FFA, SVM-RBF, SVM-QPSO, and ANN approaches for exergetic modelling of the engine. • Satisfactory performance of the SVM-WT for performance modelling of the engine over the other approaches. - Abstract: In the present study, four Support Vector Machine-based (SVM-based) approaches and the standard artificial neural network (ANN) model were designed and compared in modelling the exergetic parameters of a DI diesel engine running on diesel/biodiesel blends containing expanded polystyrene (EPS) wastes. For this aim, the SVM was coupled with discrete wavelet transform (SVM-WT), firefly algorithm (SVM-FFA), radial basis function (SVM-RBF) and quantum particle swarm optimization (SVM-QPSO). The exergetic data were computed using mass, energy, and exergy balance equations for the engine at different speeds and loads as well as various biodiesel and EPS wastes quantities. Three statistical indicators namely root means square error, coefficient of determination and Pearson coefficient were used to access the capability of the developed approaches for exergetic performance modelling of the DI diesel engine. The modelling results indicated that the SVM-WT approach was more efficient in exergetic modelling of the engine than the other three approaches. Moreover, the results obtained confirmed the effectiveness of the SVM-WT model in identifying the most exergy-efficient combustion conditions and the best fuel composition for achieving the most cost-effective and eco-friendly combustion process.

  19. The Use of Online Quizlet.com Resource Tools to Support Native English Speaking Students of Engineering and Medical Departments in Accelerated RFL Teaching and Learning

    OpenAIRE

    Kh.E. Ismailova; K. Gleason; E.A. Provotorova; P.G. Matukhin

    2016-01-01

    The paper presents a description of the methodology and some results of the application of tools of the language learning support portal Quizlet.com to improve the effectiveness of the accelerated development of the basic communicative skills in Russian as a foreign language (RFL) for the group of the English-speaking students who arrived to study in Russia engineering, medicine and other areas. The application of the development is the basics of Russian teaching and learning in the classroom...

  20. The Use of Online Quizlet.com Resource Tools to Support Native English Speaking Students of Engineering and Medical Departments in Accelerated RFL Teaching and Learning

    OpenAIRE

    Ismailova , Kh ,; Gleason , K ,; Provotorova , P ,; Matukhin , P ,

    2017-01-01

    International audience; The paper presents a description of the methodology and some results of the application of tools of the language learning support portal Quizlet.com to improve the effectiveness of the accelerated development of the basic communicative skills in Russian as a foreign language (RFL) for the group of the English-speaking students who arrived to study in Russia engineering, medicine and other areas. The application of the development is the basics of Russian teaching and l...

  1. KIVA-hpFE: Predictive turublent reactive and multiphase flow in engines : Science Supporting Mission of the Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Carrington, David Bradley [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Waters, Jiajia [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-09-26

    Research and development of KIVA-hpFE for turbulent reactive and multiphase flow particularly as related to engine modeling program has relevance to National energy security and climate change. Climate change is a source problem, and energy national security is consumption of petroleum products problem. Accurately predicting engine processes leads to, lower greenhouse gas (GHG) emission, where engines in the transportation sector currently account for 26% of the U.S. GHG emissions. Less dependence on petroleum products leads to greater energy security. By Environmental Protection Agency standards, some vehicles are now reaching 42 to the 50 mpg mark. These are conventional gasoline engines. Continued investment and research into new technical innovations, the potential exists to save more than 4 million barrels of oil per day or approximately $200 to $400 million per day. This would be a significant decrease in emission and use of petroleum and a very large economic stimulus too! It is estimated with further advancements in combustion, the current emissions can be reduced up to 40%. Enabling better understanding of fuel injection and fuel-air mixing, thermodynamic combustion losses, and combustion/emission formation processes enhances our ability to help solve both problems. To provide adequate capability for accurately simulating these processes, minimize time and labor for development of engine technology, are the goals of our KIVA development program.

  2. Engineering stategies and implications of using higher plants for throttling gas and water exchange in a controlled ecological life support system

    Science.gov (United States)

    Chamberland, Dennis; Wheeler, Raymond M.; Corey, Kenneth A.

    1993-01-01

    Engineering stategies for advanced life support systems to be used on Lunar and Mars bases involve a wide spectrum of approaches. These range from purely physical-chemical life support strategies to purely biological approaches. Within the context of biological based systems, a bioengineered system can be devised that would utilize the metabolic mechanisms of plants to control the rates of CO2 uptake and O2 evolution (photosynthesis) and water production (transpiration). Such a mechanism of external engineering control has become known as throttling. Research conducted at the John F. Kennedy Space Center's Controlled Ecological Life Support System Breadboard Project has demonstrated the potential of throttling these fluxes by changing environmental parameters affecting the plant processes. Among the more effective environmental throttles are: light and CO2 concentration for controllingthe rate of photsynthesis and humidity and CO2 concentration for controlling transpiration. Such a bioengineered strategy implies control mechanisms that in the past have not been widely attributed to life support systems involving biological components and suggests a broad range of applications in advanced life support system design.

  3. Candid Voices - Agile Combat Support From the OC-ALC Engine Shop Viewpoint. Volume XXII, Number 4

    National Research Council Canada - National Science Library

    Larvick, Jon

    1998-01-01

    .... This article will take the Agile Combat Support initiative -the focus of combat support shifts from maintaining massive inventories to establishing a response capability-as the goal and will focus...

  4. Using Self-Determination Theory to Build Communities of Support to Aid in the Retention of Women in Engineering

    Science.gov (United States)

    Dell, Elizabeth M.; Verhoeven, Yen; Christman, Jeanne W.; Garrick, Robert D.

    2018-01-01

    Diverse perspectives are required to address the technological problems facing our world. Although women perform as well as their male counterparts in math and science prior to entering college, the numbers of women students entering and completing engineering programmes are far below their representation in the workforce. This paper reports on a…

  5. Paving the Way and Passing the Torch: Mentors' Motivation and Experience of Supporting Women in Optical Engineering

    Science.gov (United States)

    Kodate, Naonori; Kodate, Kashiko; Kodate, Takako

    2014-01-01

    The phenomenon of women's underrepresentation in engineering is well known. However, the slow progress in achieving better gender equality here compared with other domains has accentuated the "numbers" issue, while the quality aspects have been largely ignored. This study aims to shed light on both these aspects via the lens of mentors,…

  6. Making It Social: Considering the Purpose of Literacy to Support Participation in Making and Engineering

    Science.gov (United States)

    Tucker-Raymond, Eli; Gravel, Brian E.; Wagh, Aditi; Wilson, Naeem; Manderino, Michael; Castek, Jill

    2016-01-01

    Digital literacies for disciplinary learning explores intersections of digital and disciplinary literacies across learning contexts such as community makerspaces and schools and examines learning across disciplines including the arts, engineering, science, social studies, language arts, and math. Columns will address work with both youth and…

  7. Paving the way and passing the torch: mentors' motivation and experience of supporting women in optical engineering

    Science.gov (United States)

    Kodate, Naonori; Kodate, Kashiko; Kodate, Takako

    2014-11-01

    The phenomenon of women's underrepresentation in engineering is well known. However, the slow progress in achieving better gender equality here compared with other domains has accentuated the 'numbers' issue, while the quality aspects have been largely ignored. This study aims to shed light on both these aspects via the lens of mentors, who are at the coalface of guiding female engineers through their education and subsequent careers. Based on data collected from 25 mentors (8 men and 17 women from 8 countries), the paper explores their experiences of being mentors, as well as their views on recommended actions for nurturing female engineers. The findings reveal that the primary motivation for becoming a mentor was personal for men and women. Many mentors from countries with relatively lower female labour participation rates perceive their roles as guarantors of their mentees' successful future career paths, and a similar trend can be found in mentors in academia. The study underscores the need for invigorating mentors' roles in order to secure a more equitable future for engineering education.

  8. Stirring the Pot: Supporting and Challenging General Education Science, Technology, Engineering, and Mathematics Faculty to Change Teaching and Assessment Practice

    Science.gov (United States)

    Stieha, Vicki; Shadle, Susan E.; Paterson, Sharon

    2016-01-01

    Evidence-based instructional practices (ebips) have been associated with positive student outcomes; however, institutions struggle to catalyze widespread adoption of these practices in general education science, technology, engineering, and mathematics (stem) courses. Further, linking ebips with integrated learning assessment is rarely discussed…

  9. Engineering Technical Support Center, Innovative Science and Technical Support for Cost-Effective Cleanups: Five Year Summary Report for 2007-2012

    Science.gov (United States)

    This report summarizes a variety of significant projects that ETSC and its colleagues in the Land Remediation and Pollution Control Division (LRPCD) have supported during the last five years. Projects have addressed an array of environmental scenarios, including remote mining co...

  10. Technique treatment of early stage support construction system for Gaoling mountain tunnel engineering of Daya Bay nuclear power station

    International Nuclear Information System (INIS)

    Ma Keli

    2010-01-01

    This article studies the technical treatment of primary support system used in Gaoling mountain tunnel construction process at Daya by nuclear power plant in combination with the new austrian tunneling construction method, this article first analyzes the design of primary support system, and the key point of the analyses lies in the primary support technical treatment schemes of Gaoling mountain tunnel with the examples of tunnel collapse and primary support design alteration for bias voltage section, then the construction technology of the primary support system is summarized, and the safety of wall rock is analyzed as well with the measurement data. In the end, suggestions are put forward on the design and construction of primary support system for tunnels on the basis of practical working experience. (author)

  11. Information engineering

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, D.N.

    1997-02-01

    The Information Engineering thrust area develops information technology to support the programmatic needs of Lawrence Livermore National Laboratory`s Engineering Directorate. Progress in five programmatic areas are described in separate reports contained herein. These are entitled Three-dimensional Object Creation, Manipulation, and Transport, Zephyr:A Secure Internet-Based Process to Streamline Engineering Procurements, Subcarrier Multiplexing: Optical Network Demonstrations, Parallel Optical Interconnect Technology Demonstration, and Intelligent Automation Architecture.

  12. Open environments to support systems engineering tool integration: A study using the Portable Common Tool Environment (PCTE)

    Science.gov (United States)

    Eckhardt, Dave E., Jr.; Jipping, Michael J.; Wild, Chris J.; Zeil, Steven J.; Roberts, Cathy C.

    1993-01-01

    A study of computer engineering tool integration using the Portable Common Tool Environment (PCTE) Public Interface Standard is presented. Over a 10-week time frame, three existing software products were encapsulated to work in the Emeraude environment, an implementation of the PCTE version 1.5 standard. The software products used were a computer-aided software engineering (CASE) design tool, a software reuse tool, and a computer architecture design and analysis tool. The tool set was then demonstrated to work in a coordinated design process in the Emeraude environment. The project and the features of PCTE used are described, experience with the use of Emeraude environment over the project time frame is summarized, and several related areas for future research are summarized.

  13. Support for the Symposium on the Application of Geophysics to Environmental and Engineering Problems, 2012-2014

    Science.gov (United States)

    2014-07-02

    or to purchase EEGS merchandise , books, past SAGEEP Proceedings, copies of the Journal of Environmental & Engineering Geophysics, and FastTIMES...utilities. GSSI, Inc. GSSI will demonstrate our very popular UtilityScan DF (Dual-Frequency). The UtilityScan DF features a 300 and 800 MHz digital ...word processors, and image file collections. Case studies will include: (1) Creating digital geologic maps with 3-D symbols, emergent cross

  14. Systems engineering and integration of control centers in support of multiple programs. [ground control for STS payloads and unmanned vehicles

    Science.gov (United States)

    Miller, David N.

    1989-01-01

    The NASA Johnson Space Center's new Multiprogram Control Center (MPCC) addresses the control requirements of complex STS payloads as well as unmanned vehicles. An account is given of the relationship of the MPCC to the STS Mission Control Center, with a view to significant difficulties that may be encountered and solutions thus far devised for generic problems. Examples of MPCC workstation applications encompass telemetry decommutation, engineering unit conversion, data-base management, trajectory processing, and flight design.

  15. Support for the in situ vitrification treatability study at the Idaho National Engineering Laboratory: FY 1988 summary

    International Nuclear Information System (INIS)

    Oma, K.H.; Reimus, M.A.H.; Timmerman, C.L.

    1989-02-01

    The objective of this project is to determine if in situ vitrification (ISV) is a viable, long-term confinement technology for previously buried solid transuranic and mixed waste at the Radioactive Waste Management Complex (RWMC). The RWMC is located at the Idaho National Engineering Laboratory (INEL). In situ vitrification is a thermal treatment process that converts contaminated soils and wastes into a durable glass and crystalline form. During processing, heavy metals or other inorganic constituents are retained and immobilized in the glass structure, and organic constituents are typically destroyed or removed for capture by an off-gas treatment system. The primary FY 1988 activities included engineering-scale feasibility tests on INEL soils containing a high metals loading. Results of engineering-scale testing indicate that wastes with a high metals content can be successfully processed by ISV. The process successfully vitrified soils containing localized metal concentrations as high as 42 wt % without requiring special methods to prevent electrical shorting within the melt zone. Vitrification of this localized concentration resulted in a 15.9 wt % metals content in the entire ISV test block. This ISV metals limit is related to the quantity of metal that accumulates at the bottom of the molten glass zone. Intermediate pilot-scale testing is recommended to determine metals content scale-up parameters in order to project metals content limits for large-scale ISV operation at INEL

  16. European research and commercialisation activities in the field of tissue engineering and liver support in world wide competition.

    Science.gov (United States)

    Marx, U; Bushnaq, H; Yalcin, E

    1998-02-01

    Tissue engineering is seen as an interesting field of technology which could improve medical therapy and could also be considered as a commercial opportunity for the European biotechnological industry. Research in the state of the art of science using the MedLine and the Science Citation Index databases, in the patent situation and of the industry dealing with tissue engineering was done. A special method, based on the Science Citation Index Journal Citation Report 1993, for evaluating scientific work was defined. The main countries working in the field of tissue engineering were evaluated in regard to their scientific performance and their patents. The R&D of German industry was investigated as an exemplary European country. Out of all activities, different tissues were rated with respect to the attention received from research and industry and with regard to the frequency in which patents were applied for. USA, Germany and Japan rank first in most tissues, especially liver. After comparing German patents with the German scientific and industrial work, it seems that the potential in German patents and research is underestimated by German industry and inefficiently exploited.

  17. Modeling approaches for characterizing and evaluating environmental exposure to engineered nanomaterials in support of risk-based decision making.

    Science.gov (United States)

    Hendren, Christine Ogilvie; Lowry, Michael; Grieger, Khara D; Money, Eric S; Johnston, John M; Wiesner, Mark R; Beaulieu, Stephen M

    2013-02-05

    As the use of engineered nanomaterials becomes more prevalent, the likelihood of unintended exposure to these materials also increases. Given the current scarcity of experimental data regarding fate, transport, and bioavailability, determining potential environmental exposure to these materials requires an in depth analysis of modeling techniques that can be used in both the near- and long-term. Here, we provide a critical review of traditional and emerging exposure modeling approaches to highlight the challenges that scientists and decision-makers face when developing environmental exposure and risk assessments for nanomaterials. We find that accounting for nanospecific properties, overcoming data gaps, realizing model limitations, and handling uncertainty are key to developing informative and reliable environmental exposure and risk assessments for engineered nanomaterials. We find methods suited to recognizing and addressing significant uncertainty to be most appropriate for near-term environmental exposure modeling, given the current state of information and the current insufficiency of established deterministic models to address environmental exposure to engineered nanomaterials.

  18. An accelerated line-by-line option for MODTRAN combining on-the-fly generation of line center absorption within 0.1 cm-1 bins and pre-computed line tails

    Science.gov (United States)

    Berk, Alexander; Conforti, Patrick; Hawes, Fred

    2015-05-01

    A Line-By-Line (LBL) option is being developed for MODTRAN6. The motivation for this development is two-fold. Firstly, when MODTRAN is validated against an independent LBL model, it is difficult to isolate the source of discrepancies. One must verify consistency between pressure, temperature and density profiles, between column density calculations, between continuum and particulate data, between spectral convolution methods, and more. Introducing a LBL option directly within MODTRAN will insure common elements for all calculations other than those used to compute molecular transmittances. The second motivation for the LBL upgrade is that it will enable users to compute high spectral resolution transmittances and radiances for the full range of current MODTRAN applications. In particular, introducing the LBL feature into MODTRAN will enable first-principle calculations of scattered radiances, an option that is often not readily available with LBL models. MODTRAN will compute LBL transmittances within one 0.1 cm-1 spectral bin at a time, marching through the full requested band pass. The LBL algorithm will use the highly accurate, pressure- and temperature-dependent MODTRAN Padé approximant fits of the contribution from line tails to define the absorption from all molecular transitions centered more than 0.05 cm-1 from each 0.1 cm-1 spectral bin. The beauty of this approach is that the on-the-fly computations for each 0.1 cm-1 bin will only require explicit LBL summing of transitions centered within a 0.2 cm-1 spectral region. That is, the contribution from the more distant lines will be pre-computed via the Padé approximants. The status of the LBL effort will be presented. This will include initial thermal and solar radiance calculations, validation calculations, and self-validations of the MODTRAN band model against its own LBL calculations.

  19. International Space Station Sustaining Engineering: A Ground-Based Test Bed for Evaluating Integrated Environmental Control and Life Support System and Internal Thermal Control System Flight Performance

    Science.gov (United States)

    Ray, Charles D.; Perry, Jay L.; Callahan, David M.

    2000-01-01

    As the International Space Station's (ISS) various habitable modules are placed in service on orbit, the need to provide for sustaining engineering becomes increasingly important to ensure the proper function of critical onboard systems. Chief among these are the Environmental Control and Life Support System (ECLSS) and the Internal Thermal Control System (ITCS). Without either, life onboard the ISS would prove difficult or nearly impossible. For this reason, a ground-based ECLSS/ITCS hardware performance simulation capability has been developed at NASA's Marshall Space Flight Center. The ECLSS/ITCS Sustaining Engineering Test Bed will be used to assist the ISS Program in resolving hardware anomalies and performing periodic performance assessments. The ISS flight configuration being simulated by the test bed is described as well as ongoing activities related to its preparation for supporting ISS Mission 5A. Growth options for the test facility are presented whereby the current facility may be upgraded to enhance its capability for supporting future station operation well beyond Mission 5A. Test bed capabilities for demonstrating technology improvements of ECLSS hardware are also described.

  20. Lysate of engineered Escherichia coli supports high-level conversion of glucose to 2,3-butanediol.

    Science.gov (United States)

    Kay, Jennifer E; Jewett, Michael C

    2015-11-01

    Cell-free metabolic engineering (CFME) is emerging as a powerful approach for the production of target molecules and pathway debugging. Unfortunately, high cofactor costs, limited cofactor and energy regeneration, and low volumetric productivities hamper the widespread use and practical implementation of CFME technology. To address these challenges, we have developed a cell-free system that harnesses ensembles of catalytic proteins prepared from crude lysates, or extracts, of cells to fuel highly active heterologous metabolic conversions. As a model pathway, we selected conversion of glucose to 2,3-butanediol (2,3-BD), a medium level commodity chemical with many industrial applications. Specifically, we engineered a single strain of Escherichia coli to express three pathway enzymes necessary to make meso-2,3-BD (m2,3-BD). We then demonstrated that lysates from this strain, with addition of glucose and catalytic amounts of cofactors NAD+ and ATP, can produce m2,3-BD. Endogenous glycolytic enzymes convert glucose to pyruvate, the starting intermediate for m2,3-BD synthesis. Strikingly, with no strain optimization, we observed a maximal synthesis rate of m2,3-BD of 11.3 ± 0.1 g/L/h with a theoretical yield of 71% (0.36 g m2,3-BD/g glucose) in batch reactions. Titers reached 82 ± 8 g/L m2,3-BD in a 30 h fed-batch reaction. Our results highlight the ability for high-level co-factor regeneration in cell-free lysates. Further, they suggest exciting opportunities to use lysate-based systems to rapidly prototype metabolic pathways and carry out molecular transformations when bioconversion yields (g product/L), productivities (g product/L/h), or cellular toxicity limit commercial feasibility of whole-cell fermentation. Copyright © 2015 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

  1. Subscale Carbon-Carbon Nozzle Extension Development and Hot Fire Testing in Support of Upper Stage Liquid Rocket Engines

    Science.gov (United States)

    Gradl, Paul; Valentine, Peter; Crisanti, Matthew; Greene, Sandy Elam

    2016-01-01

    Upper stage and in-space liquid rocket engines are optimized for performance through the use of high area ratio nozzles to fully expand combustion gases to low exit pressures increasing exhaust velocities. Due to the large size of such nozzles and the related engine performance requirements, carbon-carbon (C/C) composite nozzle extensions are being considered for use in order to reduce weight impacts. NASA and industry partner Carbon-Carbon Advanced Technologies (C-CAT) are working towards advancing the technology readiness level of large-scale, domestically-fabricated, C/C nozzle extensions. These C/C extensions have the ability to reduce the overall costs of extensions relative to heritage metallic and composite extensions and to decrease weight by 50%. Material process and coating developments have advanced over the last several years, but hot fire testing to fully evaluate C/C nozzle extensions in relevant environments has been very limited. NASA and C-CAT have designed, fabricated and hot fire tested multiple subscale nozzle extension test articles of various C/C material systems, with the goal of assessing and advancing the manufacturability of these domestically producible materials as well as characterizing their performance when subjected to the typical environments found in a variety of liquid rocket and scramjet engines. Testing at the MSFC Test Stand 115 evaluated heritage and state-of-the-art C/C materials and coatings, demonstrating the capabilities of the high temperature materials and their fabrication methods. This paper discusses the design and fabrication of the 1.2k-lbf sized carbon-carbon nozzle extensions, provides an overview of the test campaign, presents results of the hot fire testing, and discusses potential follow-on development work.

  2. Developing a Global Database of Historic Flood Events to Support Machine Learning Flood Prediction in Google Earth Engine

    Science.gov (United States)

    Tellman, B.; Sullivan, J.; Kettner, A.; Brakenridge, G. R.; Slayback, D. A.; Kuhn, C.; Doyle, C.

    2016-12-01

    There is an increasing need to understand flood vulnerability as the societal and economic effects of flooding increases. Risk models from insurance companies and flood models from hydrologists must be calibrated based on flood observations in order to make future predictions that can improve planning and help societies reduce future disasters. Specifically, to improve these models both traditional methods of flood prediction from physically based models as well as data-driven techniques, such as machine learning, require spatial flood observation to validate model outputs and quantify uncertainty. A key dataset that is missing for flood model validation is a global historical geo-database of flood event extents. Currently, the most advanced database of historical flood extent is hosted and maintained at the Dartmouth Flood Observatory (DFO) that has catalogued 4320 floods (1985-2015) but has only mapped 5% of these floods. We are addressing this data gap by mapping the inventory of floods in the DFO database to create a first-of- its-kind, comprehensive, global and historical geospatial database of flood events. To do so, we combine water detection algorithms on MODIS and Landsat 5,7 and 8 imagery in Google Earth Engine to map discrete flood events. The created database will be available in the Earth Engine Catalogue for download by country, region, or time period. This dataset can be leveraged for new data-driven hydrologic modeling using machine learning algorithms in Earth Engine's highly parallelized computing environment, and we will show examples for New York and Senegal.

  3. Supporting a Component-Based Software Engineering Approach for the Development of Takari Products and Future Command and Control Systems

    National Research Council Canada - National Science Library

    Vernik, R

    1997-01-01

    .... It focuses on concepts and approaches defined as part of the Takari programme and considers issues related to tool support for the development of Takari Capability and Technology Demonstrators (CTDs...

  4. Support of nuclear engineering education and research at the University of Michigan. Final report, September, 1992 - August, 1995

    International Nuclear Information System (INIS)

    1997-09-01

    This report describes progress on six different projects in the fission reactor area that have been supported by the grant for its three year period. These projects are: (1) improved Monte Carlo methods and utilization on massively parallel processors; (2) development of a correlated sampling methodology for multiple reactor perturbations; (3) development of an efficient Monte Carlo response history method for electron transport; (4) developing Monte Carlo benchmarks for commercial LWR configurations; (5) accelerator transmutation of nuclear waste; and (6) neutronic analysis of the Ford Nuclear Reactor. This grant was instrumental in providing a means to support research of interest to utilities in the fission reactor area that would have otherwise been impossible to support because of the lack of alternative funding sources. As a result, most all of the funding in this program went to the support of graduate research in fission reactors

  5. Proposal for the award of an industrial support contract for minor civil-engineering work at CERN

    CERN Document Server

    2006-01-01

    This document concerns the award of a contract for minor civil-engineering work at CERN. The Finance Committee is invited to agree to the negotiation of a contract with the firm LOSINGER CONSTRUCTION (CH), the lowest bidder, for the provision of minor civilengineering work at CERN for three years for a total amount not exceeding 2 840 278 Swiss francs, not subject to revision for the first two years. The contract will include options for two one-year extensions beyond the initial three-year period.

  6. Fretting fatigue cracking of a center guide bolt supporting the combustion chamber in a heavy-duty gas turbine engine

    Energy Technology Data Exchange (ETDEWEB)

    Neidel, Andreas; Fischer, Boromir; Gaedicke, Tobias [Siemens AG, Energy Sector, Gasturbinenwerk Berlin (Germany). Werkstoffprueflabor

    2018-04-01

    The slotted center guide bolt of the center guide feature of the lower part of the outer shell of an annular combustion chamber was found fractured in a heavy-duty gas turbine engine used for power generation, after approximately 5.500 operating hours. The incident was a one-off event and not a recurring incident. No similar events were reported from the fleet; hence the failure was not considered a field issue. The metallurgical root cause investigation that was ordered to determine the failure mechanism revealed that the incident center guide bolt failed by fretting fatigue cracking, a high cycle fatigue (HCF) phenomenon.

  7. Preliminary Electrochemical Characterization of Anode Supported Solid Oxide Cell (AS-SOC) Produced in the Institute of Power Engineering Operated in Electrolysis Mode (SOEC)

    Science.gov (United States)

    Kupecki, Jakub; Motyliński, Konrad; Skrzypkiewicz, Marek; Wierzbicki, Michał; Naumovich, Yevgeniy

    2017-12-01

    The article discusses the operation of solid oxide electrochemical cells (SOC) developed in the Institute of Power Engineering as prospective key components of power-to-gas systems. The fundamentals of the solid oxide cells operated as fuel cells (SOFC - solid oxide fuel cells) and electrolysers (SOEC - solid oxide fuel cells) are given. The experimental technique used for electrochemical characterization of cells is presented. The results obtained for planar cell with anodic support are given and discussed. Based on the results, the applicability of the cells in power-to-gas systems (P2G) is evaluated.

  8. Modular Engineering Concept at Novo Nordisk Engineering

    DEFF Research Database (Denmark)

    Moelgaard, Gert; Miller, Thomas Dedenroth

    1997-01-01

    This report describes the concept of a new engineering method at Novo Nordisk Engineering: Modular Engineering (ME). Three tools are designed to support project phases with different levels of detailing and abstraction. ME supports a standard, cross-functional breakdown of projects that facilitates...

  9. Advanced calculations developed for the ITER project within of engineering support framework contracts to F4E; Calculos avanzados desarrollados para el proyecto ITER dentro de los contratos marco de soporte de ingenieria para F4E

    Energy Technology Data Exchange (ETDEWEB)

    Bosch, C.; Polo, J.; Garcia Cid, J.; Guirao, J.; Fernandez, E.; Bayon, A.; Caixas, J.

    2013-07-01

    Present the different kind of analyses carried out within the engineering support framework contracts for F4E in the period 2009-2013 and its evolution according to project needs and Vacuum Vessel manufacturing status.

  10. A Trial of PBL Education with Emphasis on Improving Practical Competence of Engineering Students-A Trial Connected with the Support for Science Education in Elementary School

    Science.gov (United States)

    Tsutsumi, Hirotaka; Nikkuni, Hiroyuki; Kitakoshi, Daisuke; Yasuda, Toshitaka; Kikuchi, Akira; Mitani, Tomoyo

    Recently Colleges of technology as well as universities have some experience-oriented classes in sciences for elementary school students. These have proved to be successful as good motivation for students in the primary education to be engineers. This research has tried the PBL education, which combined the Support of Science Education in Elementary School and the improvement of students‧ practical competence in their careers. The support of science education in elementary school was carried out by using LEGO blocks, widely utilized in the educational researches of robots, and was conducted in the practical class with the autonomous robots. Finally, the method for the class was evaluated by the elementary school students on the basis of the questionnaire.

  11. Which Air Force Civil Engineer Capabilities Can Complement USNORTHCOM’s Role in Defense Support to Civil Authorities (DSCA)?

    Science.gov (United States)

    2014-05-21

    PERSONNEL FROM STANDARD PRIME BEEF OR RED 4F9K4 PROVIDES FOLDED FIBERGLASS MATTING ( FFM ) FOR AIRFIELD DAMAGE REPAIR (ADR). PACKAGE CONSISTS OF THREE FFM ...SETS (54’ X 60’), ONE FFM SUPPORT TOOL KIT, UPPER BUSHINGS, ANCHOR BUSHINGS, ANCHOR BOLTS, AND TWO EA MC-7 AIR COMPRESSORS. EACH UTC WILL BE TASKED TO...OF 7 FOLDED FIBERGLASS MAT SETS (54 FT X 60 FT), 2 FFM SUPPORT TOOL KIT, UPPER BUSHINGS, ANCHOR BUSHINGS, ANCHOR BOLTS AND 4 X MC-7 AIR COMPRESSORS

  12. Issues in visual support to real-time space system simulation solved in the Systems Engineering Simulator

    Science.gov (United States)

    Yuen, Vincent K.

    1989-01-01

    The Systems Engineering Simulator has addressed the major issues in providing visual data to its real-time man-in-the-loop simulations. Out-the-window views and CCTV views are provided by three scene systems to give the astronauts their real-world views. To expand the window coverage for the Space Station Freedom workstation a rotating optics system is used to provide the widest field of view possible. To provide video signals to as many viewpoints as possible, windows and CCTVs, with a limited amount of hardware, a video distribution system has been developed to time-share the video channels among viewpoints at the selection of the simulation users. These solutions have provided the visual simulation facility for real-time man-in-the-loop simulations for the NASA space program.

  13. NASA Engineering Design Challenges: Environmental Control and Life Support Systems. Water Filtration Challenge. EG-2008-09-134-MSFC

    Science.gov (United States)

    Schneider, Twila, Ed.

    2010-01-01

    This educator guide is organized into seven chapters: (1) Overview; (2) The Design Challenge; (3) Connections to National Curriculum Standards; (4) Preparing to Teach; (5) Classroom Sessions; (6) Opportunities for Extension; and (7) Teacher Resources. Chapter 1 provides information about Environmental Control and Life Support Systems used on NASA…

  14. Supporting information retrieval from electronic health records: A report of University of Michigan's nine-year experience in developing and using the Electronic Medical Record Search Engine (EMERSE).

    Science.gov (United States)

    Hanauer, David A; Mei, Qiaozhu; Law, James; Khanna, Ritu; Zheng, Kai

    2015-06-01

    This paper describes the University of Michigan's nine-year experience in developing and using a full-text search engine designed to facilitate information retrieval (IR) from narrative documents stored in electronic health records (EHRs). The system, called the Electronic Medical Record Search Engine (EMERSE), functions similar to Google but is equipped with special functionalities for handling challenges unique to retrieving information from medical text. Key features that distinguish EMERSE from general-purpose search engines are discussed, with an emphasis on functions crucial to (1) improving medical IR performance and (2) assuring search quality and results consistency regardless of users' medical background, stage of training, or level of technical expertise. Since its initial deployment, EMERSE has been enthusiastically embraced by clinicians, administrators, and clinical and translational researchers. To date, the system has been used in supporting more than 750 research projects yielding 80 peer-reviewed publications. In several evaluation studies, EMERSE demonstrated very high levels of sensitivity and specificity in addition to greatly improved chart review efficiency. Increased availability of electronic data in healthcare does not automatically warrant increased availability of information. The success of EMERSE at our institution illustrates that free-text EHR search engines can be a valuable tool to help practitioners and researchers retrieve information from EHRs more effectively and efficiently, enabling critical tasks such as patient case synthesis and research data abstraction. EMERSE, available free of charge for academic use, represents a state-of-the-art medical IR tool with proven effectiveness and user acceptance. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  15. Engineering study, development and prototype fabrication of the supporting system for the CLIC Two-Beam Module

    CERN Document Server

    AUTHOR|(CDS)2068725; Karyotakis, Yannis; Dahoo, Pierre Richard; Alexopoulos, Theo; MEIS, Costantin; De Conto, Jean Marie; Jeremie, Andrea; Puzot, Patrique

    CERN, the European Organization for Nuclear Research, is based on the international collaboration in the field of high-energy particle physics research. The experiments carried out in its facilities are achieved through the existing particle accelerators. In addition, advanced accelerator research and development is one of the goals of CERN. For this reason, CLIC (the Compact LInear Collider) a new electron-positron linear accelerator is being studied at CERN. CLIC is built by the assembly of the Two-Beam Modules and takes advantage of an innovative acceleration principle, the Two-Beam acceleration. Each Module contains several technical systems that contribute to its successful operation. This thesis presents the development of the prototype supporting system for the CLIC Two-Beam Module. At first, the physics requirements are translated into technical specifications and the fundamental parts of the supporting system are defined. The CLIC operational conditions are identified and the corresponding boundaries...

  16. Peer-Assisted Learning Programme: Supporting Students in High-Risk Subjects at the Mechanical Engineering Department at Walter Sisulu University

    Directory of Open Access Journals (Sweden)

    Makala Qonda

    2017-12-01

    Full Text Available The majority of the students who enroll at the Walter Sisulu University (WSU in South Africa are not equipped with the necessary academic/learning skills to cope with the university environment, especially in Mechanical Engineering. The Department of Higher Education and Training (2013, p. 17, further states that “students’ support is crucial to ensure that students adapt to the demands of college life and that they can meet the demands of college programmes”. Particularly in South Africa, the school environment might also contribute to poor student performance as a result of insufficient student support, and a lack of facilities and resources. In order to address this gap, a Peer-Assisted Learning (PAL programme was implemented to provide support targeting high-risk subjects for at-risk students in Mechanical Engineering at WSU. The programme therefore is pro-active and student-driven in that senior students assist junior students with their academic work and learning processes. The programme is designed to encourage collaborative and cooperative learning approaches during group sessions and active student engagement to support student learning (Laal & Laal, 2012. The programme requires substantial resources and time commitments. It is important from an operational, learning, and student perspective to understand in what ways the PAL programme assists students (if at all. Eliciting the experiences of students also helps the department to design interventions from a student-centred perspective using the lens of learning theories.  This qualitative case study explores the student experience of the Peer-Assisted Learning (PAL programme. Open-ended questionnaires/survey from 20 first-year students elicited their perceptions and experiences of the PAL programme. Responses were analysed thematically. Findings indicated that the students had useful insights that may contribute to revising the programme. Aspects mentioned were improved study

  17. Support of nuclear engineering education and research at the University of Michigan. Progress report, May 15, 1993--May 14, 1994

    International Nuclear Information System (INIS)

    Martin, W.R.

    1994-05-01

    This report describes progress on four different projects in the fission reactor area that have been supported by the grant during the past year. These projects are: Accelerator transmutation of nuclear waste (Steve Pearson); Neutronic analysis of the Ford Nuclear Reactor (Brent Renkema); and Monte Carlo depletion capability and new perturbation Monte Carlo algorithms, with utilization of massively parallel processors (Amit Majumdar). These tasks are briefly described and progress to date is presented

  18. Software Engineering Guidebook

    Science.gov (United States)

    Connell, John; Wenneson, Greg

    1993-01-01

    The Software Engineering Guidebook describes SEPG (Software Engineering Process Group) supported processes and techniques for engineering quality software in NASA environments. Three process models are supported: structured, object-oriented, and evolutionary rapid-prototyping. The guidebook covers software life-cycles, engineering, assurance, and configuration management. The guidebook is written for managers and engineers who manage, develop, enhance, and/or maintain software under the Computer Software Services Contract.

  19. SNF Project Engineering Process Improvement Plan

    International Nuclear Information System (INIS)

    DESAI, S.P.

    2000-01-01

    This plan documents the SNF Project activities and plans to support its engineering process. It describes five SNF Project Engineering initiatives: new engineering procedures, qualification cards process; configuration management, engineering self assessments, and integrated schedule for engineering activities

  20. Preliminary test results from a free-piston Stirling engine technology demonstration program to support advanced radioisotope space power applications

    International Nuclear Information System (INIS)

    White, Maurice A.; Qiu Songgang; Augenblick, Jack E.

    2000-01-01

    Free-piston Stirling engines offer a relatively mature, proven, long-life technology that is well-suited for advanced, high-efficiency radioisotope space power systems. Contracts from DOE and NASA are being conducted by Stirling Technology Company (STC) for the purpose of demonstrating the Stirling technology in a configuration and power level that is representative of an eventual space power system. The long-term objective is to develop a power system with an efficiency exceeding 20% that can function with a high degree of reliability for up to 15 years on deep space missions. The current technology demonstration convertors (TDC's) are completing shakedown testing and have recently demonstrated performance levels that are virtually identical to projections made during the preliminary design phase. This paper describes preliminary test results for power output, efficiency, and vibration levels. These early results demonstrate the ability of the free-piston Stirling technology to exceed objectives by approximately quadrupling the efficiency of conventional radioisotope thermoelectric generators (RTG's)

  1. Preliminary test results from a free-piston Stirling engine technology demonstration program to support advanced radioisotope space power applications

    Science.gov (United States)

    White, Maurice A.; Qiu, Songgang; Augenblick, Jack E.

    2000-01-01

    Free-piston Stirling engines offer a relatively mature, proven, long-life technology that is well-suited for advanced, high-efficiency radioisotope space power systems. Contracts from DOE and NASA are being conducted by Stirling Technology Company (STC) for the purpose of demonstrating the Stirling technology in a configuration and power level that is representative of an eventual space power system. The long-term objective is to develop a power system with an efficiency exceeding 20% that can function with a high degree of reliability for up to 15 years on deep space missions. The current technology demonstration convertors (TDC's) are completing shakedown testing and have recently demonstrated performance levels that are virtually identical to projections made during the preliminary design phase. This paper describes preliminary test results for power output, efficiency, and vibration levels. These early results demonstrate the ability of the free-piston Stirling technology to exceed objectives by approximately quadrupling the efficiency of conventional radioisotope thermoelectric generators (RTG's). .

  2. Assessed perceptions of female materials science and engineering graduates on academic advising, student support services and retention strategies

    Science.gov (United States)

    Washington, Renita Linette

    Females currently undertaking STEM-related programs can benefit from knowing about how other females who had been in a similar position as them were able to persevere through the challenges of higher education with the help of advisement and student support services that aim to increasing student retention. While there have been a depth of studies on the development of academic advising, there have been limited studies on this development with respect to the needs of specific marginalized groups. This is the gap in literature that is addressed by this study. The outcomes observed in this study can potentially benefit female students at the institution where the study was conducted. This study focused on the group of female students who were able to successfully complete their STEM-related degrees. A significant difference was found between tutoring and learning support, F = 4.65, sd = .78 and a sig. level = .004. A strong negative relationship existed between the ages of the graduates and assessed academic advisement. A perfect positive relationship existed between the age of the graduates and assessed course concierge service scores; and between the age of the graduates and assessed career services and counseling scores. A moderate negative relationship existed between the age of the graduates and assessed curriculum/degree planning database scores, the age of the graduates and assessed academic and program advisement scores and the age of the graduates and assessed tutorial and learning support services scores. A weak negative relationship existed between the age of the graduates and assessed retention scores.

  3. Knowledge engineering as a support for building an actor profile ontology for integrating Home-Care systems.

    Science.gov (United States)

    Gibert, Karina; Valls, Aida; Riaño, David

    2008-01-01

    One of the tasks towards the definition of a knowledge model for home care is the definition of the different roles of the users involved in the system. The roles determine the actions and services that can or must be performed by each type of user. In this paper the experience of building an ontology to represent the home-care users and their associated information is presented, in a proposal for a standard model of a Home-Care support system to the European Community.

  4. The Impact of the Dimensions of the Administrative Decision Support Systems on the Re-engineering of the Systems of the Palestinian universities in Gaza Strip from the Employees’ Perspective

    Directory of Open Access Journals (Sweden)

    Mazen Jehad I. Al Shobaki

    2017-08-01

    Full Text Available This study aimed to identify the impact of the dimensions of the administrative decision support systems on the re-engineering of the systems of the Palestinian universities in Gaza Strip from the standpoint of employees. A descriptive approach was used through which a questionnaire was developed and distributed to a stratified random sample. (500 questionnaires were distributed and (449 were returned, with (89.8% response rate. The study revealed these results: There was an effect for the potentials (physical, human, technical, and organizational design available for the decision support systems and re-engineering of the systems in the Palestinian higher education institutions in Gaza Strip.There were significant differences between the assessment means of the study sample about the impact of decision support systems to re-engineer the systems in the Palestinian higher education institutions in Gaza Strip due to the gender variable in favor of males. There also differences due to the name of the university variable in favor of the Islamic University, Al Azhar University, Al Aqsa University, respectively. It was recommended that Palestinian higher education institutions which intend to start re-engineering the systems should be encouraged immediately start the process. These institutions should also develop the infrastructure of the decisions support systems when re-engineering their operations. Keywords: Decision support systems, Re-engineering, Palestinian higher education institutions.

  5. Google Earth Engine, Open-Access Satellite Data, and Machine Learning in Support of Large-Area Probabilistic Wetland Mapping

    Directory of Open Access Journals (Sweden)

    Jennifer N. Hird

    2017-12-01

    Full Text Available Modern advances in cloud computing and machine-leaning algorithms are shifting the manner in which Earth-observation (EO data are used for environmental monitoring, particularly as we settle into the era of free, open-access satellite data streams. Wetland delineation represents a particularly worthy application of this emerging research trend, since wetlands are an ecologically important yet chronically under-represented component of contemporary mapping and monitoring programs, particularly at the regional and national levels. Exploiting Google Earth Engine and R Statistical software, we developed a workflow for predicting the probability of wetland occurrence using a boosted regression tree machine-learning framework applied to digital topographic and EO data. Working in a 13,700 km2 study area in northern Alberta, our best models produced excellent results, with AUC (area under the receiver-operator characteristic curve values of 0.898 and explained-deviance values of 0.708. Our results demonstrate the central role of high-quality topographic variables for modeling wetland distribution at regional scales. Including optical and/or radar variables into the workflow substantially improved model performance, though optical data performed slightly better. Converting our wetland probability-of-occurrence model into a binary Wet-Dry classification yielded an overall accuracy of 85%, which is virtually identical to that derived from the Alberta Merged Wetland Inventory (AMWI: the contemporary inventory used by the Government of Alberta. However, our workflow contains several key advantages over that used to produce the AMWI, and provides a scalable foundation for province-wide monitoring initiatives.

  6. Service Cart For Engines

    Science.gov (United States)

    Ng, Gim Shek

    1995-01-01

    Cart supports rear-mounted air-cooled engine from Volkswagen or Porsche automobile. One person removes, repairs, tests, and reinstalls engine of car, van, or home-built airplane. Consists of framework of wood, steel, and aluminum components supported by four wheels. Engine lifted from vehicle by hydraulic jack and gently lowered onto waiting cart. Jack removed from under engine. Rear of vehicle raised just enough that engine can be rolled out from under it. Cart easily supports 200-lb engine. Also used to hold transmission. With removable sheet-metal top, cart used as portable seat.

  7. The Use of Online Quizlet.com Resource Tools to Support Native English Speaking Students of Engineering and Medical Departments in Accelerated RFL Teaching and Learning

    Directory of Open Access Journals (Sweden)

    Kh.E. Ismailova

    2016-05-01

    Full Text Available The paper presents a description of the methodology and some results of the application of tools of the language learning support portal Quizlet.com to improve the effectiveness of the accelerated development of the basic communicative skills in Russian as a foreign language (RFL for the group of the English-speaking students who arrived to study in Russia engineering, medicine and other areas. The application of the development is the basics of Russian teaching and learning in the classroom as well as in the mode of self-education and out-of-classroom events. Special attention is paid to the use of cloud-based tools to organize and conduct extracurricular activities. Particularly in the promising subject connected with the use of 3D printers for the solution of engineering problems of prosthetics of the lost bodies of animals and birds on the example of the Toucan key restoration. Analysis of the results of the use of flash cards, tests, and group games showed the promise of using the sets of Quizlet.com tools for accelerated assimilation of the native English speaking students in the area of General and special RFL vocabulary, as well as students showed that in a short time they can get and develop their basic skills of listening, reading and writing in Russian communication when Quizlet tools being used in different modes.

  8. Conceptual study of nuclear power generation facilities life-cycle support versatile engineering database. Procedure of development and consideration of fundamental functions

    International Nuclear Information System (INIS)

    Endo, Hidetoshi

    2009-05-01

    International Atomic Energy Agency (IAEA) stands out the activity of the knowledge management of nuclear safety and the movement to introduce the idea of the life cycle management into the quality control of maintenance of the nuclear power generation facilities to assure the knowledge preservation and to succeed the technology of facilities. Japan Atomic Energy Agency (JAEA) also has such activities as the knowledge preservation of research and development, and related information. The facilities' performance reliability can be easily checked with the technology of data processing in the general industry and the results of the knowledge repository, transmitting technology and knowledge management by referring to the information and knowledge if the information and knowledge at each step of the life-cycle of facilities can be built. This report shows the strategy of the construction of the engineering database to support the life cycle of facilities and the basic function of the management system. (author)

  9. Engineering mathematics

    CERN Document Server

    Bird, John

    2014-01-01

    A practical introduction to the core mathematics required for engineering study and practiceNow in its seventh edition, Engineering Mathematics is an established textbook that has helped thousands of students to succeed in their exams.John Bird's approach is based on worked examples and interactive problems. This makes it ideal for students from a wide range of academic backgrounds as the student can work through the material at their own pace. Mathematical theories are explained in a straightforward manner, being supported by practical engineering examples and applications in order to ensure

  10. Engine Environment Research Facility (EERF)

    Data.gov (United States)

    Federal Laboratory Consortium — Description: This facility supports research and development testing of the behavior of turbine engine lubricants, fuels and sensors in an actual engine environment....

  11. MIGRATING AUTOLUX WEBSITE FROM MODX TO PHALCONPHP WITH FURTHER DEVELOPMENTS (Search Engine Optimization and Mobile Application Support Implementation

    Directory of Open Access Journals (Sweden)

    Hana Tanjung

    2017-01-01

    Full Text Available Autolux Project is owned by DTT Multimedia B.V. Autolux is a platform for car lovers sharing their information about favorite or latest cars. The website was built in MODx (CMS framework which considered being old and heavy by the company. With that very reason, a project to migrate the website from MODx into PhalconPHP (pure PHP framework was started. Migrating website from MODx to PhalconPHP was a success, and to boost the website popularity, the first thing to do is to implement the SEO standards. Another demand by the company was for the website to be responsive and using OOP standarts. Responsive website can be reached by using the help of libraries. PhalconPHP already implemented OOP, thus the developer will follow the MVC pattern given and refine it by doing more separation of concerns. Later on, the developer also put more refinements on the website to boost the speed of page loading, support multilingual, and management system.

  12. Supplement analysis of transuranic waste characterization and repackaging activities at the Idaho National Engineering Laboratory in support of the Waste Isolation Pilot Plant test program

    International Nuclear Information System (INIS)

    1991-03-01

    This supplement analysis has been prepared to describe new information relevant to waste retrieval, handling, and characterization at the Idaho National Engineering Laboratory (INEL) and to evaluate the need for additional documentation to satisfy the National Environmental Policy Act (NEPA). The INEL proposes to characterize and repackage contact-handled transuranic waste to support the Waste Isolation Pilot Plant (WIPP) Test Phase. Waste retrieval, handling and processing activities in support of test phase activities at the WIPP were addressed in the Supplemental Environmental Impact Statement (SEIS) for the WIPP. To ensure that test-phase wastes are properly characterized and packaged, waste containers would be retrieved, nondestructively examined, and transported from the Radioactive Waste Management Complex (RWMC) to the Hot-Fuel Examination Facility for headspace gas analysis, visual inspections to verify content code, and waste acceptance criteria compliance, then repackaging into WIPP experimental test bins or returned to drums. Following repackaging the characterized wastes would be returned to the RWMC. Waste characterization would help DOE determine WIPP compliance with US Environmental Protection Agency regulations governing disposal of transuranic waste and hazardous waste. Additionally, this program supports onsite compliance with Resource Conservation and Recovery Act (RCRA) requirements, compliance with the terms of the No-Migration Variance at WIPP, and provides data to support future waste shipments to WIPP. This analysis will help DOE determine whether there have been substantial changes made to the proposed action at the INEL, or if preparation of a supplement to the WIPP Final Environmental Impact Statement (DOE, 1980) and SEIS (DOE, 1990a) is required. This analysis is based on current information and includes details not available to the SEIS

  13. Modelo de conocimiento conceptual como apoyo a la Ingeniería del Conocimiento Conceptual knowledge modeling as support in knowledge engineering

    Directory of Open Access Journals (Sweden)

    Mónica Henao-Calad

    2012-12-01

    Full Text Available Este artículo presenta una propuesta del uso de modelos de conocimientos para apoyar los procesos de Ingeniería del Conocimiento. El modelo de conocimiento propuesto permite representar el conocimiento declarativo de un dominio de una manera estructurada, a través de la técnica de representación de conocimiento de mapas conceptuales. La Ingeniería del Conocimiento se ha relacionado con el desarrollo de sistemas basados en el conocimiento en el cual el conocimiento y el razonamiento juegan un papel primordial. Como disciplina, dirige la tarea de construir sistemas inteligentes proporcionando herramientas y métodos que soportan el desarrollo de estos sistemas, involucrando: obtención de conocimiento, familiarización con el dominio, análisis y el diseño de la solución, y validación del conocimiento. Todo esto integra los procesos de la Ingeniería del Conocimiento: adquisición, representación y manipulación / validación del conocimiento. En este artículo se muestra cómo un modelo de conocimientos basado en mapas conceptuales apoya la realización de cada uno de esos procesos, permitiendo que los conceptos del dominio sean fácilmente identificados y jerarquizados, logrando generar una visión global del dominio y una homologación de sus conceptos. Adicionalmente, se presenta el caso de un modelo de conocimiento desarrollado por el grupo de la Gerencia en Colombia de la Universidad EAFIT3 como parte del proyecto "Petroleum Geology of Colombia" que se realizó en el Departamento de Geología de esta universidad y patrocinado por la Agencia Nacional de Hidrocarburos - ANH4 de Colombia, en el que se representó el conocimiento de geólogos e ingenieros expertos en cuencas petrolíferas colombianas.This article introduces a proposal for knowledge models use to support knowledge engineering processes. The proposed knowledge model allows the presentation on a structured way of a domain's declarative knowledge, through the knowledge

  14. Development of the re-engineered European decision support system for off-site nuclear and radiological emergencies - JRODOS. Application to air pollution transport modelling

    International Nuclear Information System (INIS)

    Ievdin, I.; Treebushny, D.; Raskob, W.; Zheleznyak, M.

    2008-01-01

    Full text: The European decision support system for nuclear and radiological emergencies RODOS includes a set of numerical models simulating the transport of radionuclides in the environment, estimating potential doses to the public and simulating and evaluating the efficiency of countermeasures. The re-engineering of the RODOS system using the Java technology has started recently which will allow to apply the new system called JRODOS on nearly any computational platform running Java virtual machine. Modern software development approaches were used for the JRODOS system architecture and implementation: distributed system design (client, management server, computational server), geo-database utilization, plug-in model structure and OpenMI-like compatibility to support seamless model inter-connection. Stable open source components such as an ORM solution (Hibernate), an OpenGIS component (Geotools) and a charting/reporting component (JFree, Pentaho) were utilized to optimize the development effort and allow a fast completion of the project. The architecture of the system is presented and illustrated for the atmospheric dispersion module ALSMC (Atmospheric Local Scale Model Chain) performing calculations of atmospheric pollution transport and the corresponding acute doses and dose rates. The example application is based on a synthetic scenario of a release from a nuclear power plant located in Europe. (author)

  15. Minority engineering scholarships, 2012.

    Science.gov (United States)

    2014-02-01

    Scholarships for Minority Students Studying Engineering and Science: Support will make scholarships available to minority students : interested in engineering and science and will increase significantly the number of minority students that Missouri S...

  16. Turbomachine Sealing and Secondary Flows - Part 3. Part 3; Review of Power-Stream Support, Unsteady Flow Systems, Seal and Disk Cavity Flows, Engine Externals, and Life and Reliability Issues

    Science.gov (United States)

    Hendricks, R. C.; Steinetz, B. M.; Zaretsky, E. V.; Athavale, M. M.; Przekwas, A. J.

    2004-01-01

    The issues and components supporting the engine power stream are reviewed. It is essential that companies pay close attention to engine sealing issues, particularly on the high-pressure spool or high-pressure pumps. Small changes in these systems are reflected throughout the entire engine. Although cavity, platform, and tip sealing are complex and have a significant effect on component and engine performance, computational tools (e.g., NASA-developed INDSEAL, SCISEAL, and ADPAC) are available to help guide the designer and the experimenter. Gas turbine engine and rocket engine externals must all function efficiently with a high degree of reliability in order for the engine to run but often receive little attention until they malfunction. Within the open literature statistically significant data for critical engine components are virtually nonexistent; the classic approach is deterministic. Studies show that variations with loading can have a significant effect on component performance and life. Without validation data they are just studies. These variations and deficits in statistical databases require immediate attention.

  17. Towards the Development and Validation of a Global Field Size and Irrigation Map using Crowdsourcing, Mobile Apps and Google Earth Engine in support of GEOGLAM

    Science.gov (United States)

    Fritz, S.; Nordling, J.; See, L. M.; McCallum, I.; Perger, C.; Becker-Reshef, I.; Mucher, S.; Bydekerke, L.; Havlik, P.; Kraxner, F.; Obersteiner, M.

    2014-12-01

    The International Institute for Applied Systems Analysis (IIASA) has developed a global cropland extent map, which supports the monitoring and assessment activities of GEOGLAM (Group on Earth Observations Global Agricultural Monitoring Initiative). Through the European-funded SIGMA (Stimulating Innovation for Global Monitoring of Agriculture and its Impact on the Environment in support of GEOGLAM) project, IIASA is continuing to support GEOGLAM by providing cropland projections in the future and modelling environmental impacts on agriculture under various scenarios. In addition, IIASA is focusing on two specific elements within SIGMA: the development of a global field size and irrigation map; and mobile app development for in-situ data collection and validation of remotely-sensed products. Cropland field size is a very useful indicator for agricultural monitoring yet the information we have at a global scale is currently very limited. IIASA has already created a global map of field size at a 1 km resolution using crowdsourced data from Geo-Wiki as a first approximation. Using automatic classification of Landsat imagery and algorithms contained within Google Earth Engine, initial experimentation has shown that circular fields and landscape structures can easily be extracted. Not only will this contribute to improving the global map of field size, it can also be used to create a global map that contains a large proportion of the world's irrigated areas, which will be another useful contribution to GEOGLAM. The field size map will also be used to stratify and develop a global crop map in SIGMA. Mobile app development in support of in-situ data collection is another area where IIASA is currently working. An Android app has been built using the Open Data Toolkit (ODK) and extended further with spatial mapping capabilities called GeoODK. The app allows users to collect data on different crop types and delineate fields on the ground, which can be used to validate the

  18. Citizen observatory of water as a data engine supporting the people-hydrology nexus: experience of the WeSenseIt project

    Science.gov (United States)

    Ferri, Michele; Baruffi, Francesco; Norbiato, Daniele; Monego, Martina; Tomei, Giovanni; Solomatine, Dimitri; Alfonso, Leonardo; Mazzoleni, Maurizio; Chacon, Juan Carlos; Wehn, Uta; Ciravegna, Fabio

    2016-04-01

    Citizen observatories (COs) present an interesting case of strong multi-facet feedback between the physical (water) system and humans. CO is a form of crowdsourcing ensuring a data flow from citizens observing environment (e.g. water level in a river) to a central data processing unit which is typically part of a more complex social arrangement (e.g. water authorities responsible for flood forecasting). The EU-funded project WeSenseIt (www.wesenseit.eu) aims at developing technologies and tools supporting creation of such COs [1,2,3,4]. Citizens which form a CO play the role of "social sensors" which however are very specific. The data streams from such sensors have varying temporal and spatial coverage and information value (uncertainty). The crowdsourced data can be of course simply visualized and presented to public, but it is much more interesting to consider cases when such data are assimilated into the existing forecasting systems, e.g. flood early warning systems based on hydrological and hydraulic models. COs may also affect water management and governance [4], and in fact can be seen as data engines supporting the people-hydrology nexus. In the framework of WeSenseIt project several approaches were developed allowing for optimal assimilation of intermittent data streams with varying spatial coverage into distributed hydrological models [1, 2]. The mentioned specific features of CO data required updates of the existing data assimilation algorithms (Ensemble Kalman Filter was used as the basic algorithm). The developed algorithms have been implemented in the operational flood forecasting systems of the Alto Adriatico Water Authority (AAWA), Venice. In this paper we analyse various scenarios of employing citizens data (COs) for flood forecasting. This study is partly supported by the FP7 European Project WeSenseIt Citizen Water Observatory (www.http://wesenseit.eu/). References [1] Mazzoleni, M., Alfonso, L., Chacon-Hurtado, J., Solomatine, D. (2015

  19. Engineering Encounters: Engineering Adaptations

    Science.gov (United States)

    Gatling, Anne; Vaughn, Meredith Houle

    2015-01-01

    Engineering is not a subject that has historically been taught in elementary schools, but with the emphasis on engineering in the "Next Generation Science Standards," curricula are being developed to explicitly teach engineering content and design. However, many of the scientific investigations already conducted with students have…

  20. Unified Engineering Software System

    Science.gov (United States)

    Purves, L. R.; Gordon, S.; Peltzman, A.; Dube, M.

    1989-01-01

    Collection of computer programs performs diverse functions in prototype engineering. NEXUS, NASA Engineering Extendible Unified Software system, is research set of computer programs designed to support full sequence of activities encountered in NASA engineering projects. Sequence spans preliminary design, design analysis, detailed design, manufacturing, assembly, and testing. Primarily addresses process of prototype engineering, task of getting single or small number of copies of product to work. Written in FORTRAN 77 and PROLOG.

  1. Systems engineering simplified

    CERN Document Server

    Cloutier, Robert; Bone, Mary Alice

    2015-01-01

    IntroductionOverviewDiscussion of Common TerminologyThe Case for Systems EngineeringA Brief History of Systems EngineeringSystem ExamplesSummaryThe System Life CycleManaging System Development-The Vee ModelSystem ProductionSystem Utilization and SupportSystem Retirement and DisposalOther Systems Engineering Development ModelsSpiral ModelAgile Model for Systems EngineeringSystem of InterestAbstraction and DecompositionIntegrationDeveloping and Managing RequirementsCyclone Requiremen

  2. International Conference on Software Engineering, Knowledge Engineering and Information Engineering (SEKEIE 2012)

    CERN Document Server

    Software Engineering and Knowledge Engineering: Theory and Practice

    2012-01-01

    2012 International Conference on Software Engineering, Knowledge Engineering and Information Engineering (SEKEIE 2012) will be held in Macau, April 1-2, 2012 . This conference will bring researchers and experts from the three areas of Software Engineering, Knowledge Engineering and Information Engineering together to share their latest research results and ideas.   This volume book covered significant recent developments in the Software Engineering, Knowledge Engineering and Information Engineering field, both theoretical and applied. We are glad this conference attracts your attentions, and thank your support to our conference. We will absorb remarkable suggestion, and make our conference more successful and perfect.

  3. Cognitive Systems Engineering Tool Survey - A Subtask in Support of Commander's Decision Aids for Predictive Battle-Space Awareness (CDA4PBA)

    National Research Council Canada - National Science Library

    Sanders, Mary; Fitzhugh, Elisabeth

    2005-01-01

    ...) DO 6, Commander's Decision Aids for Predictive Battle-Space Awareness, (CDA4PBA) is to identify system requirements necessary to capture the entire software and systems engineering process from concept...

  4. Building Information Modeling (BIM): A Road Map for Implementation to Support MILCON Transformation and Civil Works Projects within the U.S. Army Corps of Engineers

    National Research Council Canada - National Science Library

    Brucker, Beth A; Case, Michael P; East, E. W; Huston, Brian K; Nachtigall, Susan D; Shockley, Johnette C; Spangler, Steve C; Wilson, James T

    2006-01-01

    .... The challenge to the U.S. Army Corps of Engineers (USACE) is to proactively prepare for BIM, use it to drive down costs and delivery time, and maintain or even improve quality at the same time...

  5. University/Science Center Collaborations (A Science Center Perspective): Developing an Infrastructure of Partnerships with Science Centers to Support the Engagement of Scientists and Engineers in Education and Outreach for Broad Impact

    Science.gov (United States)

    Marshall, Eric

    2009-03-01

    Science centers, professional associations, corporations and university research centers share the same mission of education and outreach, yet come from ``different worlds.'' This gap may be bridged by working together to leverage unique strengths in partnership. Front-end evaluation results for the development of new resources to support these (mostly volunteer-based) partnerships elucidate the factors which lead to a successful relationship. Maintaining a science museum-scientific community partnership requires that all partners devote adequate resources (time, money, etc.). In general, scientists/engineers and science museum professionals often approach relationships with different assumptions and expectations. The culture of science centers is distinctly different from the culture of science. Scientists/engineers prefer to select how they will ultimately share their expertise from an array of choices. Successful partnerships stem from clearly defined roles and responsibilities. Scientists/engineers are somewhat resistant to the idea of traditional, formal training. Instead of developing new expertise, many prefer to offer their existing strengths and expertise. Maintaining a healthy relationship requires the routine recognition of the contributions of scientists/engineers. As professional societies, university research centers and corporations increasingly engage in education and outreach, a need for a supportive infrastructure becomes evident. Work of TryScience.org/VolTS (Volunteers TryScience), the MRS NISE Net (Nanoscale Informal Science Education Network) subcommittee, NRCEN (NSF Research Center Education Network), the IBM On Demand Community, and IEEE Educational Activities exemplify some of the pieces of this evolving infrastructure.

  6. Civil Support Operations

    Science.gov (United States)

    2010-08-01

    marijuana eradication; linguist support; air and ground transportation; intelligence analysis; tunnel detection; engineering support; and...optical, infra-red and synthetic aperture radar imagery, as well as full motion video. Incident awareness and assessment requirements are based on the

  7. Enhancing Engineering Students’ Reading Comprehension of English for Science and Technology With the Support of an Online Cumulative Sentence Analysis System

    Directory of Open Access Journals (Sweden)

    Yea-Ru Tsai

    2014-09-01

    Full Text Available For engineering students, reading in English is the core competence to absorb professional knowledge in academic settings and their future career, because many authentic textbooks and information about advanced technology have been published in English. The present study sets out to improve English reading comprehension among tertiary-level engineering students. An online reading strategy instruction based on cumulative sentence analysis (CSA was constructed to enhance the students’ reading comprehension of English technology texts. The comparison between the pre-test and post-test showed that the participants achieved a higher level of reading comprehension performance following the instruction. The findings clearly demonstrated that online CSA strategy instruction is an efficient and feasible approach to helping engineering students cope with their problems of reading English texts. Pedagogical implications are briefly discussed based on the findings of this study.

  8. Culture in Engineering Education

    DEFF Research Database (Denmark)

    Hoffmann, Birgitte; Jørgensen, Ulrik; Christensen, Hans Peter

    2011-01-01

    As engineers today often work in intercultural projects and contexts, intercultural competences must be part of the learning objectives in engineering educations. Cultural aspects of engineering education should not just be treated as a question of appropriate communication and teaching: cultural...... aspects are basically part of engineering discipli¬nes, work challenges as well as the contextual elements in engineering curriculum [1,2]. This is reflected in the aims of the CDIO programme [3,4]; however, the programme, as well as the teaching practises, undoubtedly needs to further develop approaches...... to cultural aspects in engineering education. Hence the key-question of this paper is how CDIO support the development of intercultural competences in engineering education. The paper explores the implementation of CDIO in an intercultural arctic engineering programme in Greenland that since 2001 has been...

  9. Direct and Lead Units During Preparation for the Battle (Battlefield Function 19) as Accomplished by an Engineer Battalion Supporting a Heavy Brigade. Volume 1: Function Analysis

    National Research Council Canada - National Science Library

    Clagg, Robert

    1998-01-01

    The purpose of the overall research program was to document the synchronization required by command and control tasks performed within the armored brigade, to include combat support and combat service support units...

  10. Plan for Combat Operations (Battlefield Function 18) as Accomplished by an Engineer Battalion Supporting a Heavy Brigade. Volume 1: Function Analysis

    National Research Council Canada - National Science Library

    Anderson, Martin

    1997-01-01

    The purpose of the overall research program was to document the synchronization required by command and control tasks performed within the armored brigade, to include combat support and combat service support units...

  11. Plan for Combat Operations (Battlefield Function 18) as Accomplished by an Engineer Battalion Supporting a Heavy Brigade. Volume 2: Assessment Package

    National Research Council Canada - National Science Library

    Mullen, William

    1997-01-01

    The purpose of the overall research program was to document the synchronization required by command and control tasks performed within the armored brigade to include combat support and combat service support units...

  12. Direct and Lead Units in Execution of Battle (Battlefield Function 20) as Accomplished by an Engineer Battalion Supporting a Heavy Brigade. Volume 2: Assessment Package

    National Research Council Canada - National Science Library

    Mullen, William

    1997-01-01

    The purpose of the overall research program was to document the synchronization required by command and control tasks performed within the armored brigade to include combat support and combat service support units...

  13. Solar powered Stirling engine

    Energy Technology Data Exchange (ETDEWEB)

    Meijer, R.J.

    1987-11-24

    In a solar dish module which comprises a dish which receives incident solar rays and reflects them to a focus at which is located the combination of a receiver and a heat engine organized and arranged so that the heat energy of the reflected solar rays collected at the receiver powers the engine, and wherein the receiver and heat engine are supported from the dish by a framework, the improvement is described which comprises journal means for journaling at least the engine on the framework to maintain certain predetermined spatial orientation for the engine in relation to the direction of gravity irrespective of spatial orientation of the dish.

  14. Women in science & engineering and minority engineering scholarships : year 5.

    Science.gov (United States)

    2011-06-01

    Support will make scholarships available to minority and women students interested in engineering and science and will increase : significantly the number of minority and female students that Missouri S&T can recruit to its science and engineering pr...

  15. Women in science & engineering and minority engineering scholarships : year 4.

    Science.gov (United States)

    2010-04-01

    Support will make scholarships available to minority and women students interested in engineering and science and will increase : significantly the number of minority and female students that Missouri S&T can recruit to its science and engineering pr...

  16. Towards a new curriculum to support the changing front end innovation landscape : Educating engineering students to effectively participate in iterative data-enabled product development processes

    NARCIS (Netherlands)

    van Kollenburg, J.W.M.; Jeedella, Shawhkat Y.; van Kollenburg, P.A.M.; Kargas, Sotirios

    The new generation of Internet of Things product offers exciting opportunities to design and develop highly personal and adaptive products. Engineering students are traditionally not trained to use user data, generated by prototypes, as creative material for ideating the Fuzzy Front End phase of the

  17. Minority engineering scholarships renewal, 2011.

    Science.gov (United States)

    2012-08-01

    Scholarships for Minority Students Studying Engineering and Science : Support will make scholarships available to minority students : interested in engineering and science and will increase significantly the number of minority students that Missouri ...

  18. Technical support of standards for high-level radioactive waste management. Volume B. Engineering controls. Task b report Mar-Aug 77

    International Nuclear Information System (INIS)

    1979-01-01

    This report is the result of work performed under the second part (Task B) of a four-part contract to gather technical information to evaluate enviornmental acceptablity of various options for disposing high-level wastes. The other tasks are: A-Source Term Characterization; C-Assessment of Migration Pathways; D-Assessment of Accidental Pathways. The scope of work for Task B was divided into 2 major steps: analysis of technology for engineering control of high-level wastes, and projections of costs for various alternative disposal technologies. Primary emphasis has been placed in non-reprocessed spent fuel. Brief consideration has been given to lower-level transuranic contaminated wastes which arise primarily from plutonium fuel fabrication and reprocessing plants. The objective of this limited review is to provide some insight into the state of the art for applying engineering controls to such wastes, including, where necessary, direct burial with high-level wastes in a geologic disposal facility

  19. Biocommodity Engineering.

    Science.gov (United States)

    Lynd; Wyman; Gerngross

    1999-10-01

    , for example, production of fuels, chemicals, power, and/or feed, is likely to be essential for economic viability. Lifecycle analysis is necessary to verify the sustainability and environmental quality benefits of a particular biocommodity product or process. We see biocommodity engineering as a legitimate focus for graduate study, which is responsive to an established personnel demand in an industry that is expected to grow in the future. Graduate study in biocommodity engineering is supported by a distinctive blend of intellectual elements, including biotechnology, process engineering, and resource and environmental systems.

  20. The gerontechnology engineer

    NARCIS (Netherlands)

    Bronswijk, van J.E.M.H.; Brink, M.; Vlies, van der R.D.

    2011-01-01

    Pushing supportive technology to serve an aging society originated from the social sciences. Only about 20 years ago did engineers discover the field and formulated it as gerontechnology. The question arises whether engineers and social scientists have succeeded to form a community of practice with

  1. Unplanned ecological engineering

    DEFF Research Database (Denmark)

    Andersen, Ken Haste; Gislason, Henrik

    2017-01-01

    unexpectedly large catches by removing predators from the ecosystem. Such ecosystem engineering stands in stark contrast to reigning management paradigms that do not allow fishing down predators to increase the productivity of their prey. The theoretical support for such a feat of ecosystem engineering is well...

  2. Engineer Ethics

    International Nuclear Information System (INIS)

    Lee, Dae Sik; Kim, Yeong Pil; Kim, Yeong Jin

    2003-03-01

    This book tells of engineer ethics such as basic understanding of engineer ethics with history of engineering as a occupation, definition of engineering and specialized job and engineering, engineer ethics as professional ethics, general principles of ethics and its limitation, ethical theory and application, technique to solve the ethical problems, responsibility, safety and danger, information engineer ethics, biotechnological ethics like artificial insemination, life reproduction, gene therapy and environmental ethics.

  3. Reverse engineering for quality systems

    International Nuclear Information System (INIS)

    Nolan, A.J.

    1995-01-01

    When the age of software engineering began, many companies were faced with a problem of how to support the older, pre-software-engineering, programs. The techniques of reverse engineering and re-engineering were developed to bridge the gap between the past and the present. Although reverse engineering can be used for generating missing documentation, it can also be used as a means to demonstrate quality in these older programs. This paper presents, in the form of a case study, how Rolls-Royce and Associates Limited addressed the quality issues of reverse engineering and re-engineering. (author)

  4. Educating the humanitarian engineer.

    Science.gov (United States)

    Passino, Kevin M

    2009-12-01

    The creation of new technologies that serve humanity holds the potential to help end global poverty. Unfortunately, relatively little is done in engineering education to support engineers' humanitarian efforts. Here, various strategies are introduced to augment the teaching of engineering ethics with the goal of encouraging engineers to serve as effective volunteers for community service. First, codes of ethics, moral frameworks, and comparative analysis of professional service standards lay the foundation for expectations for voluntary service in the engineering profession. Second, standard coverage of global issues in engineering ethics educates humanitarian engineers about aspects of the community that influence technical design constraints encountered in practice. Sample assignments on volunteerism are provided, including a prototypical design problem that integrates community constraints into a technical design problem in a novel way. Third, it is shown how extracurricular engineering organizations can provide a theory-practice approach to education in volunteerism. Sample completed projects are described for both undergraduates and graduate students. The student organization approach is contrasted with the service-learning approach. Finally, long-term goals for establishing better infrastructure are identified for educating the humanitarian engineer in the university, and supporting life-long activities of humanitarian engineers.

  5. Streaming Weak Submodularity: Interpreting Neural Networks on the Fly

    OpenAIRE

    Elenberg, Ethan R.; Dimakis, Alexandros G.; Feldman, Moran; Karbasi, Amin

    2017-01-01

    In many machine learning applications, it is important to explain the predictions of a black-box classifier. For example, why does a deep neural network assign an image to a particular class? We cast interpretability of black-box classifiers as a combinatorial maximization problem and propose an efficient streaming algorithm to solve it subject to cardinality constraints. By extending ideas from Badanidiyuru et al. [2014], we provide a constant factor approximation guarantee for our algorithm...

  6. Learn on the Fly: Quiescent Routing in Wireless Sensor Networks

    Science.gov (United States)

    2005-02-01

    quality solely based on data traf- fic without employing beacons. Using a realistic sensor network traffic trace and an 802.11b testbed of 195 Stargates ...testbed of 195 Stargates [1] with 802.11b radios. For instance, we investigate the validity of geographic uniformity which is assumed in literature [19...Figure 1), we deploy 29 Stargates in a straight line, with a 45-meter separation between any two consecutive Stargates . The Stargates run Linux with

  7. The Way We Were...Education on the Fly.

    Science.gov (United States)

    Gibson, Dave

    2001-01-01

    Describes an early distance learning program called the Midwest Program on Airborne Television Instruction (MPATI) which used broadcast television and an airplane, eventually to be replaced by satellites. Discusses elements needed for successful distance education programs, including a usable and affordable technology and high quality…

  8. Making friends on the fly advances in ad hoc teamwork

    CERN Document Server

    Barrett, Samuel

    2015-01-01

    This book is devoted to the encounter and interaction of agents such as robots with other agents and describes how they cooperate with their previously unknown teammates, forming an Ad Hoc team. It presents a new algorithm, PLASTIC, that allows agents to quickly adapt to new teammates by reusing knowledge learned from previous teammates.  PLASTIC is instantiated in both a model-based approach, PLASTIC-Model, and a policy-based approach, PLASTIC-Policy.  In addition to reusing knowledge learned from previous teammates, PLASTIC also allows users to provide expert-knowledge and can use transfer learning (such as the new TwoStageTransfer algorithm) to quickly create models of new teammates when it has some information about its new teammates. The effectiveness of the algorithm is demonstrated on three domains, ranging from multi-armed bandits to simulated robot soccer games.

  9. On-the-fly Overlapping of Sparse Generations

    DEFF Research Database (Denmark)

    Sørensen, Chres Wiant; Roetter, Daniel Enrique Lucani; Fitzek, Frank

    2014-01-01

    Traditionally, the idea of overlapping generations in network coding research has focused on reducing the complexity of decoding large data files while maintaining the delay performance expected of a system that combines all data packets. However, the effort for encoding and decoding individual g...

  10. On-the Fly Merging of Attitude Solutions

    DEFF Research Database (Denmark)

    Jørgensen, Peter Siegbjørn; Jørgensen, John Leif; Denver, Troelz

    2008-01-01

    Recent advances in autonomous attitude determination instrumentation enable even small satellites flying fully autonomous multi head star trackers providing full accurate and robust attitude information. Each sensor provides the full attitude information but for robustness and optimal usage...... of the available information, i.e. optimal accuracy, methods for merging such data should be investigated. The need for and desirability of attitude merging depends on the mission objective and available resources. To enable real-time attitude control and reduce requirements on download budget, on-board merging...... of attitude data will often be advantageous. This should be weighted against the need for post observation reconstruction of attitudes, especially needed when end products are sensitive to optimal attitude reconstruction. Instrument integrated merging algorithms will reduce the complexity of on-board AOCS...

  11. Biomedical engineering support. Annual progress report, August 15, 1974--August 14, 1975. [/sup 238/PuO/sub 2/-powered mechanical heart

    Energy Technology Data Exchange (ETDEWEB)

    Kolff, W.J.; Smith, L.M.; Sandquist, G.M.

    1975-01-01

    The major responsibility of the Institute for Biomedical Engineering at the University of Utah under the ERDA Artificial Heart Program has been to provide in vitro and in vivo experimental data and evaluation of the anatomical fitting, accommodation, performance and adequacy of the artificial heart system and its components as they are developed in the ERDA Program and provided to the Institute for study. The Institute also has the responsibility of designing, constructing and testing the blood handling components of the Blood Pump and insuring reliability, durability and satisfactory performance of these system components. During the reporting period, nine total heart replacement experiments were performed in calves using the ERDA Blood Pump powered by an electric motor implanted in the abdomen. Results of the experiments are given. Ultimately the mechanical heart will be powered by a radioisotope heat source. (TFD)

  12. Engineering one-dimensional and two-dimensional birnessite manganese dioxides on nickel foam-supported cobalt–aluminum layered double hydroxides for advanced binder-free supercapacitors

    KAUST Repository

    Hao, Xiaodong; Zhang, Yuxin; Diao, Zengpeng; Chen, Houwen; Zhang, Aiping; Wang, Zhongchang

    2014-01-01

    © The Royal Society of Chemistry. We report a facile decoration of the hierarchical nickel foam-supported CoAl layered double hydroxides (CoAl LDHs) with MnO2 nanowires and nanosheets by a chemical bath method and a hydrothermal approach for high

  13. Engineering opportunities in nuclear engineering

    International Nuclear Information System (INIS)

    Walton, D.G.

    1980-01-01

    The pattern of education and training of Nuclear Engineers in the UK is outlined under the headings; degree courses for professional engineers, postgraduate courses, education of technician engineers. Universities which offer specific courses are stated and useful addresses listed. (UK)

  14. Method Engineering: Engineering of Information Systems Development Methods and Tools

    OpenAIRE

    Brinkkemper, J.N.; Brinkkemper, Sjaak

    1996-01-01

    This paper proposes the term method engineering for the research field of the construction of information systems development methods and tools. Some research issues in method engineering are identified. One major research topic in method engineering is discussed in depth: situational methods, i.e. the configuration of a project approach that is tuned to the project at hand. A language and support tool for the engineering of situational methods are discussed.

  15. GeoDash: Assisting Visual Image Interpretation in Collect Earth Online by Leveraging Big Data on Google Earth Engine

    Science.gov (United States)

    Markert, K. N.; Ashmall, W.; Johnson, G.; Saah, D. S.; Anderson, E.; Flores Cordova, A. I.; Díaz, A. S. P.; Mollicone, D.; Griffin, R.

    2017-12-01

    Collect Earth Online (CEO) is a free and open online implementation of the FAO Collect Earth system for collaboratively collecting environmental data through the visual interpretation of Earth observation imagery. The primary collection mechanism in CEO is human interpretation of land surface characteristics in imagery served via Web Map Services (WMS). However, interpreters may not have enough contextual information to classify samples by only viewing the imagery served via WMS, be they high resolution or otherwise. To assist in the interpretation and collection processes in CEO, SERVIR, a joint NASA-USAID initiative that brings Earth observations to improve environmental decision making in developing countries, developed the GeoDash system, an embedded and critical component of CEO. GeoDash leverages Google Earth Engine (GEE) by allowing users to set up custom browser-based widgets that pull from GEE's massive public data catalog. These widgets can be quick looks of other satellite imagery, time series graphs of environmental variables, and statistics panels of the same. Users can customize widgets with any of GEE's image collections, such as the historical Landsat collection with data available since the 1970s, select date ranges, image stretch parameters, graph characteristics, and create custom layouts, all on-the-fly to support plot interpretation in CEO. This presentation focuses on the implementation and potential applications, including the back-end links to GEE and the user interface with custom widget building. GeoDash takes large data volumes and condenses them into meaningful, relevant information for interpreters. While designed initially with national and global forest resource assessments in mind, the system will complement disaster assessments, agriculture management, project monitoring and evaluation, and more.

  16. GeoDash: Assisting Visual Image Interpretation in Collect Earth Online by Leveraging Big Data on Google Earth Engine

    Science.gov (United States)

    Markert, Kel; Ashmall, William; Johnson, Gary; Saah, David; Mollicone, Danilo; Diaz, Alfonso Sanchez-Paus; Anderson, Eric; Flores, Africa; Griffin, Robert

    2017-01-01

    Collect Earth Online (CEO) is a free and open online implementation of the FAO Collect Earth system for collaboratively collecting environmental data through the visual interpretation of Earth observation imagery. The primary collection mechanism in CEO is human interpretation of land surface characteristics in imagery served via Web Map Services (WMS). However, interpreters may not have enough contextual information to classify samples by only viewing the imagery served via WMS, be they high resolution or otherwise. To assist in the interpretation and collection processes in CEO, SERVIR, a joint NASA-USAID initiative that brings Earth observations to improve environmental decision making in developing countries, developed the GeoDash system, an embedded and critical component of CEO. GeoDash leverages Google Earth Engine (GEE) by allowing users to set up custom browser-based widgets that pull from GEE's massive public data catalog. These widgets can be quick looks of other satellite imagery, time series graphs of environmental variables, and statistics panels of the same. Users can customize widgets with any of GEE's image collections, such as the historical Landsat collection with data available since the 1970s, select date ranges, image stretch parameters, graph characteristics, and create custom layouts, all on-the-fly to support plot interpretation in CEO. This presentation focuses on the implementation and potential applications, including the back-end links to GEE and the user interface with custom widget building. GeoDash takes large data volumes and condenses them into meaningful, relevant information for interpreters. While designed initially with national and global forest resource assessments in mind, the system will complement disaster assessments, agriculture management, project monitoring and evaluation, and more.

  17. Integrated Support Environment (ISE) Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — Purpose:The Integrated Support Environment (ISE) Laboratory serves the fleet, in-service engineers, logisticians and program management offices by automatically and...

  18. Engineering Institute

    Science.gov (United States)

    Projects Past Projects Publications NSEC » Engineering Institute Engineering Institute Multidisciplinary engineering research that integrates advanced modeling and simulations, novel sensing systems and new home of Engineering Institute Contact Institute Director Charles Farrar (505) 665-0860 Email UCSD EI

  19. Mechanical engineering

    CERN Document Server

    Darbyshire, Alan

    2010-01-01

    Alan Darbyshire's best-selling text book provides five-star high quality content to a potential audience of 13,000 engineering students. It explains the most popular specialist units of the Mechanical Engineering, Manufacturing Engineering and Operations & Maintenance Engineering pathways of the new 2010 BTEC National Engineering syllabus. This challenging textbook also features contributions from specialist lecturers, ensuring that no stone is left unturned.

  20. An Efficient Workflow Environment to Support the Collaborative Development of Actionable Climate Information Using the NCAR Climate Risk Management Engine (CRMe)

    Science.gov (United States)

    Ammann, C. M.; Vigh, J. L.; Lee, J. A.

    2016-12-01

    Society's growing needs for robust and relevant climate information have fostered an explosion in tools and frameworks for processing climate projections. Many top-down workflows might be employed to generate sets of pre-computed data and plots, frequently served in a "loading-dock style" through a metadata-enabled search and discovery engine. Despite these increasing resources, the diverse needs of applications-driven projects often result in data processing workflow requirements that cannot be fully satisfied using past approaches. In parallel to the data processing challenges, the provision of climate information to users in a form that is also usable represents a formidable challenge of its own. Finally, many users do not have the time nor the desire to synthesize and distill massive volumes of climate information to find the relevant information for their particular application. All of these considerations call for new approaches to developing actionable climate information. CRMe seeks to bridge the gap between the diversity and richness of bottom-up needs of practitioners, with discrete, structured top-down workflows typically implemented for rapid delivery. Additionally, CRMe has implemented web-based data services capable of providing focused climate information in usable form for a given location, or as spatially aggregated information for entire regions or countries following the needs of users and sectors. Making climate data actionable also involves summarizing and presenting it in concise and approachable ways. CRMe is developing the concept of dashboards, co-developed with the users, to condense the key information into a quick summary of the most relevant, curated climate data for a given discipline, application, or location, while still enabling users to efficiently conduct deeper discovery into rich datasets on an as-needed basis.

  1. Modern Engineering : Science and Education

    CERN Document Server

    2016-01-01

    This book draws together the most interesting recent results to emerge in mechanical engineering in Russia, providing a fascinating overview of the state of the art in the field in that country which will be of interest to a wide readership. A broad range of topics and issues in modern engineering are discussed, including dynamics of machines, materials engineering, structural strength and tribological behavior, transport technologies, machinery quality and innovations. The book comprises selected papers presented at the conference "Modern Engineering: Science and Education", held at the Saint Petersburg State Polytechnic University in 2014 with the support of the Russian Engineering Union. The authors are experts in various fields of engineering, and all of the papers have been carefully reviewed. The book will be of interest to mechanical engineers, lecturers in engineering disciplines and engineering graduates.

  2. Engineering thinking in emergency situations: A new nuclear safety concept.

    Science.gov (United States)

    Guarnieri, Franck; Travadel, Sébastien

    2014-11-01

    The lessons learned from the Fukushima Daiichi accident have focused on preventive measures designed to protect nuclear reactors, and crisis management plans. Although there is still no end in sight to the accident that occurred on March 11, 2011, how engineers have handled the aftermath offers new insight into the capacity of organizations to adapt in situations that far exceed the scope of safety standards based on probabilistic risk assessment and on the comprehensive identification of disaster scenarios. Ongoing crises in which conventional resources are lacking, but societal expectations are high, call for "engineering thinking in emergency situations." This is a new concept that emphasizes adaptability and resilience within organizations-such as the ability to create temporary new organizational structures; to quickly switch from a normal state to an innovative mode; and to integrate a social dimension into engineering activities. In the future, nuclear safety oversight authorities should assess the ability of plant operators to create and implement effective engineering strategies on the fly, and should require that operators demonstrate the capability for resilience in the aftermath of an accident.

  3. New technologies for the support of risk management. A systems-engineering point of view for the creation of risk information systems

    International Nuclear Information System (INIS)

    Beroggi, G.E.G.

    1995-01-01

    Within the framework of the poly project, the partial project 'Methodical Fundamentals and Computer Supported Risk Management' has developed two RISs (Risk Information Systems). The aim of the present book is to present the viewpoints gained in these new technologies and model formation attempts with which new RISs can be conceived and created. Because of the numerous new attempts, a compromise had to be made between the breadth and depth of the discussions whereby the breadth was preferred; which means that the aim is to define the broad range of RIS development as comprehensively as possible. The reader is meant to be motivated to think about the new technologies and their role in risk management. figs., tabs., refs

  4. Basic engineering mathematics

    CERN Document Server

    Bird, John

    2014-01-01

    Introductory mathematics written specifically for students new to engineering Now in its sixth edition, Basic Engineering Mathematics is an established textbook that has helped thousands of students to succeed in their exams. John Bird's approach is based on worked examples and interactive problems. This makes it ideal for students from a wide range of academic backgrounds as the student can work through the material at their own pace. Mathematical theories are explained in a straightforward manner, being supported by practical engineering examples and applications in order to ensure that readers can relate theory to practice. The extensive and thorough topic coverage makes this an ideal text for introductory level engineering courses. This title is supported by a companion website with resources for both students and lecturers, including lists of essential formulae, multiple choice tests, full solutions for all 1,600 further questions contained within the practice exercises, and biographical information on t...

  5. Underground openings in clay formations - Technical requirements on drifting technology and support systems for underground openings and their impact on retreat systems for the installation of engineered barriers

    International Nuclear Information System (INIS)

    Mischo, Helmut

    2012-01-01

    well as the development of adapted mining and excavation methods. Other fields which have to be considered are the special requirements on the suitable support technology and systems, the necessary support installation technology and also time requirements. Most of these special requirements can also be applied to the excavation of large-scale underground openings in mud-stone and can thus provide additional information for the design and development of underground repositories in clay formations. While most information can be transferred directly from commercial mining to the excavation of a repository, there are some areas where the available data only provides some sort of basic information. One example for this is the fact that the retreat from old workings and the sealing of drifts and tunnels already requires a highly developed and adopted technology in normal clay mining operations. For the successful long-term sealing of a repository, However, the immediate expansion of the pre-stressed clay after the extraction of support units and the simultaneously starting creeping requests an even more sophisticated dam construction technology for the refinement of radioactive waste to guarantee highest quality of the dam itself. This has to include, amongst other things, excellent bonding between construction material and host rock to ensure lowest possible leakage. This paper gives a detailed overview of the technical and technological methods currently used in clay mining and the significant differences to all other types of mining operations. For each stage of the technical construction process of underground openings in clay formations it highlights the information that could be transferred to the construction of this type of underground repositories. It also shows some of the areas where the database is still limited or incomplete and thus where further research and development work is necessary for a successful technical solution for radioactive waste confinement in

  6. Microcapsules engineered to support mesenchymal stem cell (MSC) survival and proliferation enable long-term retention of MSCs in infarcted myocardium.

    Science.gov (United States)

    Blocki, Anna; Beyer, Sebastian; Dewavrin, Jean-Yves; Goralczyk, Anna; Wang, Yingting; Peh, Priscilla; Ng, Michael; Moonshi, Shehzahdi S; Vuddagiri, Susmitha; Raghunath, Michael; Martinez, Eliana C; Bhakoo, Kishore K

    2015-06-01

    The limited efficacy of cardiac cell-based therapy is thought to be due to poor cell retention within the myocardium. Hence, there is an urgent need for biomaterials that aid in long-term cell retention. This study describes the development of injectable microcapsules for the delivery of mesenchymal stem cells (MSCs) into the infarcted cardiac wall. These microcapsules comprise of low concentrations of agarose supplemented with extracellular matrix (ECM) proteins collagen and fibrin. Dextran sulfate, a negatively charged polycarbohydrate, was added to mimic glycosaminoglycans in the ECM. Cell viability assays showed that a combination of all components is necessary to support long-term survival and proliferation of MSCs within microcapsules. Following intramyocardial transplantation, microcapsules degraded slowly in vivo and did not induce a fibrotic foreign body response. Pre-labeling of encapsulated MSCs with iron oxide nanoparticles allowed continued cell-tracking by MRI over several weeks following transplantation into infarcted myocardium. In contrast, MSCs injected as cell suspension were only detectable for two days post transplantation by MRI. Histological analysis confirmed integration of transplanted cells at the infarct site. Therefore, microcapsules proved to be suitable for stem cell delivery into the infarcted myocardium and can overcome current limitations of poor cell retention in cardiac cell-based therapy. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Engineering one-dimensional and two-dimensional birnessite manganese dioxides on nickel foam-supported cobalt–aluminum layered double hydroxides for advanced binder-free supercapacitors

    KAUST Repository

    Hao, Xiaodong

    2014-11-19

    © The Royal Society of Chemistry. We report a facile decoration of the hierarchical nickel foam-supported CoAl layered double hydroxides (CoAl LDHs) with MnO2 nanowires and nanosheets by a chemical bath method and a hydrothermal approach for high-performance supercapacitors. We demonstrate that owing to the sophisticated configuration of binder-free LDH@MnO2 on the conductive Ni foam (NF), the designed NF/LDH@MnO2 nanowire composites exhibit a highly boosted specific capacitance of 1837.8 F g-1 at a current density of 1 A g-1, a good rate capability, and an excellent cycling stability (91.8% retention after 5000 cycles). By applying the hierarchical NF/LDH@MnO2 nanowires as the positive electrode and activated microwave exfoliated graphite oxide activated graphene as the negative electrode, the fabricated asymmetric supercapacitor produces an energy density of 34.2 Wh kg-1 with a maximum power density of 9 kW kg-1. Such strategies with controllable assembly capability could open up a new and facile avenue in fabricating advanced binder-free energy storage electrodes. This journal is

  8. 14 CFR 23.361 - Engine torque.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Engine torque. 23.361 Section 23.361... Engine torque. (a) Each engine mount and its supporting structure must be designed for the effects of— (1) A limit engine torque corresponding to takeoff power and propeller speed acting simultaneously with...

  9. 14 CFR 25.361 - Engine torque.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Engine torque. 25.361 Section 25.361... STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Supplementary Conditions § 25.361 Engine torque. (a) Each engine mount and its supporting structure must be designed for the effects of— (1) A limit engine torque...

  10. Jet Engine Control Using Ethernet with a BRAIN (Postprint)

    National Research Council Canada - National Science Library

    Hall, Brendan; Paulitsch, Michael; Benson, Dewey; Behbahani, Alireza

    2008-01-01

    .... However, achieving a distributed architecture that supports the increasing computational demands of engine control and prognostics strategies whilst surviving in the harsh on-engine environment...

  11. Restructuring to Achieve Joint Engineer Integration and Transformation

    National Research Council Canada - National Science Library

    Kelly, Paul

    2003-01-01

    .... Increased joint engineer operations, including new homeland defense support requirements, transformation of the joint force, and the growing need for efficient use of scarce engineer resources...

  12. Engineering Cartilage

    Science.gov (United States)

    ... Research Matters NIH Research Matters March 3, 2014 Engineering Cartilage Artistic rendering of human stem cells on ... situations has been a major goal in tissue engineering. Cartilage contains water, collagen, proteoglycans, and chondrocytes. Collagens ...

  13. Governing Engineering

    DEFF Research Database (Denmark)

    Buch, Anders

    2012-01-01

    Most people agree that our world face daunting problems and, correctly or not, technological solutions are seen as an integral part of an overall solution. But what exactly are the problems and how does the engineering ‘mind set’ frame these problems? This chapter sets out to unravel dominant...... perspectives in challenge per-ception in engineering in the US and Denmark. Challenge perception and response strategies are closely linked through discursive practices. Challenge perceptions within the engineering community and the surrounding society are thus critical for the shaping of engineering education...... and the engineering profession. Through an analysis of influential reports and position papers on engineering and engineering education the chapter sets out to identify how engineering is problematized and eventually governed. Drawing on insights from governmentality studies the chapter strives to elicit the bodies...

  14. Industrial Engineering

    DEFF Research Database (Denmark)

    Karlsson, Christer

    2015-01-01

    Industrial engineering is a discipline that is concerned with increasing the effectiveness of (primarily) manufacturing and (occasionally).......Industrial engineering is a discipline that is concerned with increasing the effectiveness of (primarily) manufacturing and (occasionally)....

  15. Governing Engineering

    DEFF Research Database (Denmark)

    Buch, Anders

    2011-01-01

    Abstract: Most people agree that our world faces daunting problems and, correctly or not, technological solutions are seen as an integral part of an overall solution. But what exactly are the problems and how does the engineering ‘mind set’ frame these problems? This chapter sets out to unravel...... dominant perspectives in challenge perception in engineering in the US and Denmark. Challenge perception and response strategies are closely linked through discursive practices. Challenge perceptions within the engineering community and the surrounding society are thus critical for the shaping...... of engineering education and the engineering profession. Through an analysis of influential reports and position papers on engineering and engineering education the chapter sets out to identify how engineering is problematized and eventually governed. Drawing on insights from governmentality studies the chapter...

  16. Computer Engineers.

    Science.gov (United States)

    Moncarz, Roger

    2000-01-01

    Looks at computer engineers and describes their job, employment outlook, earnings, and training and qualifications. Provides a list of resources related to computer engineering careers and the computer industry. (JOW)

  17. Engineering _ litteraturliste

    DEFF Research Database (Denmark)

    Sillasen, Martin Krabbe; Daugbjerg, Peer; Nielsen, Keld

    2017-01-01

    Litteraturliste udarbejdet som grundlag for artiklen ”Engineering – svaret på naturfagenes udfordringer?”......Litteraturliste udarbejdet som grundlag for artiklen ”Engineering – svaret på naturfagenes udfordringer?”...

  18. International Expert Review of SRCan: Engineered Barrier Issues. External review contribution in support of SKI's and SSI's review of SR-Can

    International Nuclear Information System (INIS)

    Savage, David; Bennett, David; Apted, Mick; Saellfors, Goeran; Saario, Timo; Segle, Peter

    2008-03-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) has recently submitted a license application for the construction of a spent fuel encapsulation plant. SKB plans to submit a further license application in 2009 for the construction of a repository for the disposal spent nuclear fuel. In connection with the first of these applications, SKB published a safety report, known as SR-Can, which assessed the safety of a spent-fuel repository. The Swedish Nuclear Power Inspectorate (SKI) and the Swedish Radiation Protection Authority (SSI) (the Authorities) will make formal reviews of the licence applications, and have, therefore, jointly commissioned a team of independent experts to assess and provide comments on SKB's safety reports. The Authorities will consider the views of the independent review team in completing their own reviews. This document presents the comments and findings of the Engineered Barrier System (EBS) review group on SR-Can. The SR-Can safety report includes an examination of EBS design and performance for a range of scenarios, including expected repository evolution and possible variant scenarios, that together address processes and events that might result in the loss of certain repository safety functions. Furthermore, a series of sensitivity analyses is also presented that provides helpful insights into the relative importance of many key parameters and processes related to the EBS. In general, the explanatory text of the SR-Can safety report is clear, and the cited references provide adequate technical justifications for the assumptions, models, and data that are abstracted into the SR-Can safety report. The review group considers, therefore, that SKB's development of SR-Can has been a very valuable exercise, and that SKB should be congratulated on the breadth, depth and general clarity of its research and development and safety assessment programmes. Notwithstanding these successes, the EBS review group has identified a range of

  19. International Expert Review of SRCan: Engineered Barrier Issues. External review contribution in support of SKI's and SSI's review of SR-Can

    Energy Technology Data Exchange (ETDEWEB)

    Savage, David (Quintessa Limited, Henley-on-Thames (GB)); Bennett, David (TerraSalus Limited, Oakham (GB)); Apted, Mick (Monitor Scientific LLC, Denver, CO (US)); Saellfors, Goeran (Chalmers Univ. of Technology, Goeteborg (SE)); Saario, Timo (VTT Materials and Building (FI)); Segle, Peter (Inspecta, Stockholm (SE))

    2008-03-15

    The Swedish Nuclear Fuel and Waste Management Company (SKB) has recently submitted a license application for the construction of a spent fuel encapsulation plant. SKB plans to submit a further license application in 2009 for the construction of a repository for the disposal spent nuclear fuel. In connection with the first of these applications, SKB published a safety report, known as SR-Can, which assessed the safety of a spent-fuel repository. The Swedish Nuclear Power Inspectorate (SKI) and the Swedish Radiation Protection Authority (SSI) (the Authorities) will make formal reviews of the licence applications, and have, therefore, jointly commissioned a team of independent experts to assess and provide comments on SKB's safety reports. The Authorities will consider the views of the independent review team in completing their own reviews. This document presents the comments and findings of the Engineered Barrier System (EBS) review group on SR-Can. The SR-Can safety report includes an examination of EBS design and performance for a range of scenarios, including expected repository evolution and possible variant scenarios, that together address processes and events that might result in the loss of certain repository safety functions. Furthermore, a series of sensitivity analyses is also presented that provides helpful insights into the relative importance of many key parameters and processes related to the EBS. In general, the explanatory text of the SR-Can safety report is clear, and the cited references provide adequate technical justifications for the assumptions, models, and data that are abstracted into the SR-Can safety report. The review group considers, therefore, that SKB's development of SR-Can has been a very valuable exercise, and that SKB should be congratulated on the breadth, depth and general clarity of its research and development and safety assessment programmes. Notwithstanding these successes, the EBS review group has identified a range

  20. Stirling engine design manual

    Science.gov (United States)

    Martini, W. R.

    1978-01-01

    This manual is intended to serve both as an introduction to Stirling engine analysis methods and as a key to the open literature on Stirling engines. Over 800 references are listed and these are cross referenced by date of publication, author and subject. Engine analysis is treated starting from elementary principles and working through cycles analysis. Analysis methodologies are classified as first, second or third order depending upon degree of complexity and probable application; first order for preliminary engine studies, second order for performance prediction and engine optimization, and third order for detailed hardware evaluation and engine research. A few comparisons between theory and experiment are made. A second order design procedure is documented step by step with calculation sheets and a worked out example to follow. Current high power engines are briefly described and a directory of companies and individuals who are active in Stirling engine development is included. Much remains to be done. Some of the more complicated and potentially very useful design procedures are now only referred to. Future support will enable a more thorough job of comparing all available design procedures against experimental data which should soon be available.

  1. Computational engineering

    CERN Document Server

    2014-01-01

    The book presents state-of-the-art works in computational engineering. Focus is on mathematical modeling, numerical simulation, experimental validation and visualization in engineering sciences. In particular, the following topics are presented: constitutive models and their implementation into finite element codes, numerical models in nonlinear elasto-dynamics including seismic excitations, multiphase models in structural engineering and multiscale models of materials systems, sensitivity and reliability analysis of engineering structures, the application of scientific computing in urban water management and hydraulic engineering, and the application of genetic algorithms for the registration of laser scanner point clouds.

  2. Architectural Engineers

    DEFF Research Database (Denmark)

    Petersen, Rikke Premer

    engineering is addresses from two perspectives – as an educational response and an occupational constellation. Architecture and engineering are two of the traditional design professions and they frequently meet in the occupational setting, but at educational institutions they remain largely estranged....... The paper builds on a multi-sited study of an architectural engineering program at the Technical University of Denmark and an architectural engineering team within an international engineering consultancy based on Denmark. They are both responding to new tendencies within the building industry where...... the role of engineers and architects increasingly overlap during the design process, but their approaches reflect different perceptions of the consequences. The paper discusses some of the challenges that design education, not only within engineering, is facing today: young designers must be equipped...

  3. Tissue engineering

    CERN Document Server

    Fisher, John P; Bronzino, Joseph D

    2007-01-01

    Increasingly viewed as the future of medicine, the field of tissue engineering is still in its infancy. As evidenced in both the scientific and popular press, there exists considerable excitement surrounding the strategy of regenerative medicine. To achieve its highest potential, a series of technological advances must be made. Putting the numerous breakthroughs made in this field into a broad context, Tissue Engineering disseminates current thinking on the development of engineered tissues. Divided into three sections, the book covers the fundamentals of tissue engineering, enabling technologies, and tissue engineering applications. It examines the properties of stem cells, primary cells, growth factors, and extracellular matrix as well as their impact on the development of tissue engineered devices. Contributions focus on those strategies typically incorporated into tissue engineered devices or utilized in their development, including scaffolds, nanocomposites, bioreactors, drug delivery systems, and gene t...

  4. Transforming Systems Engineering through Model-Centric Engineering

    Science.gov (United States)

    2018-02-28

    Contract No. HQ0034-13-D-0004 Research Tasks: 48, 118, 141, 157, 170 Report No. SERC-2018-TR-103 Transforming Systems Engineering through...Model-Centric Engineering Technical Report SERC-2018-TR-103 February 28, 2018 Principal Investigator Dr. Mark Blackburn, Stevens Institute of...Systems Engineering Research Center This material is based upon work supported, in whole or in part, by the U.S. Department of Defense through the

  5. Generic methods for aero-engine exhaust emission prediction

    NARCIS (Netherlands)

    Shakariyants, S.A.

    2008-01-01

    In the thesis, generic methods have been developed for aero-engine combustor performance, combustion chemistry, as well as airplane aerodynamics, airplane and engine performance. These methods specifically aim to support diverse emission prediction studies coupled with airplane and engine

  6. The end of meta search engines in Europe?

    NARCIS (Netherlands)

    Husovec, Martin

    2015-01-01

    The technology behind the meta search engines supports countless number of Internet services ranging from the price and quality comparison websites to more sophisticated traffic connection finders and general search engines like Google. Meta search engines generally increase market transparency,

  7. Multimedia Software Laboratory | College of Engineering & Applied Science

    Science.gov (United States)

    Support Milwaukee Engineering Research Conference 2018 Poster Competition Business Corporate Partners Engineer Research Collaborations Corporate Services Product Realization Business Tour Give Entrepreneurship -oriented methods, and performance analysis. Research Message from the Associate Dean Milwaukee Engineerâ

  8. Engineering mechanics

    CERN Document Server

    Gross, Dietmar; Schröder, Jörg; Wall, Wolfgang A; Rajapakse, Nimal

    Statics is the first volume of a three-volume textbook on Engineering Mechanics. The authors, using a time-honoured straightforward and flexible approach, present the basic concepts and principles of mechanics in the clearest and simplest form possible to advanced undergraduate engineering students of various disciplines and different educational backgrounds. An important objective of this book is to develop problem solving skills in a systematic manner. Another aim of this volume is to provide engineering students as well as practising engineers with a solid foundation to help them bridge the gap between undergraduate studies on the one hand and advanced courses on mechanics and/or practical engineering problems on the other. The book contains numerous examples, along with their complete solutions. Emphasis is placed upon student participation in problem solving. The contents of the book correspond to the topics normally covered in courses on basic engineering mechanics at universities and colleges. Now in i...

  9. Invisible Engineers

    Science.gov (United States)

    Ohashi, Hideo

    Questionnaire to ask “mention three names of scientists you know” and “three names of engineers you know” was conducted and the answers from 140 adults were analyzed. The results indicated that the image of scientists is represented by Nobel laureates and that of engineers by great inventors like Thomas Edison and industry founders like Soichiro Honda. In order to reveal the image of engineers among young generation, questionnaire was conducted for pupils in middle and high schools. Answers from 1,230 pupils were analyzed and 226 names mentioned as engineers were classified. White votes reached 60%. Engineers who are neither big inventors nor company founders collected less than 1% of named votes. Engineers are astonishingly invisible from young generation. Countermeasures are proposed.

  10. Global engineering

    International Nuclear Information System (INIS)

    Plass, L.

    2001-01-01

    This article considers the challenges posed by the declining orders in the plant engineering and contracting business in Germany, the need to remain competitive, and essential preconditions for mastering the challenge. The change in engineering approach is illustrated by the building of a methanol plant in Argentina by Lurgi with the basic engineering completed in Frankfurt with involvement of key personnel from Poland, completely engineered subsystems from a Brazilian subsupplier, and detailed engineering work in Frankfurt. The production of methanol from natural gas using the LurgiMega/Methanol process is used as a typical example of the industrial plant construction sector. The prerequisites for successful global engineering are listed, and error costs in plant construction, possible savings, and process intensification are discussed

  11. TWRS engineering bibliography software listing

    International Nuclear Information System (INIS)

    Husa, E.I.

    1995-01-01

    This document contains the computer software listing for Engineering Bibliography software, developed by E. Ivar Husa. This software is in the working prototype stage of development. The code has not been tested to requirements. TWRS Engineering created this software for engineers to share bibliographic references across the Hanford site network (HLAN). This software is intended to store several hundred to several thousand references (a compendium with limited range). Coded changes are needed to support the larger number of references

  12. Computer aided control engineering

    DEFF Research Database (Denmark)

    Szymkat, Maciej; Ravn, Ole

    1997-01-01

    Current developments in the field of Computer Aided Control Engineering (CACE) have a visible impact on the design methodologies and the structure of the software tools supporting them. Today control engineers has at their disposal libraries, packages or programming environments that may...... in CACE enhancing efficient flow of information between the tools supporting the following phases of the design process. In principle, this flow has to be two-way, and more or less automated, in order to enable the engineer to observe the propagation of the particular design decisions taken at various...... levels.The major conclusions of the paper are related with identifying the factors affecting the software tool integration in a way needed to facilitate design "inter-phase" communication. These are: standard application interfaces, dynamic data exchange mechanisms, code generation techniques and general...

  13. Human engineering

    International Nuclear Information System (INIS)

    Yang, Seong Hwan; Park, Bum; Gang, Yeong Sik; Gal, Won Mo; Baek, Seung Ryeol; Choe, Jeong Hwa; Kim, Dae Sung

    2006-07-01

    This book mentions human engineering, which deals with introduction of human engineering, Man-Machine system like system design, and analysis and evaluation of Man-Machine system, data processing and data input, display, system control of man, human mistake and reliability, human measurement and design of working place, human working, hand tool and manual material handling, condition of working circumstance, working management, working analysis, motion analysis working measurement, and working improvement and design in human engineering.

  14. Engineering Electromagnetics

    International Nuclear Information System (INIS)

    Kim, Se Yun

    2009-01-01

    This book deals with engineering electromagnetics. It contains seven chapters, which treats understanding of engineering electromagnetics such as magnet and electron spin, current and a magnetic field and an electromagnetic wave, Essential tool for engineering electromagnetics on rector and scalar, rectangular coordinate system and curl vector, electrostatic field with coulomb rule and method of electric images, Biot-Savart law, Ampere law and magnetic force, Maxwell equation and an electromagnetic wave and reflection and penetration of electromagnetic plane wave.

  15. Software engineering

    CERN Document Server

    Sommerville, Ian

    2010-01-01

    The ninth edition of Software Engineering presents a broad perspective of software engineering, focusing on the processes and techniques fundamental to the creation of reliable, software systems. Increased coverage of agile methods and software reuse, along with coverage of 'traditional' plan-driven software engineering, gives readers the most up-to-date view of the field currently available. Practical case studies, a full set of easy-to-access supplements, and extensive web resources make teaching the course easier than ever.

  16. Tool support for distributed software engineering

    NARCIS (Netherlands)

    Spanjers, H.; Ter Huurne, M.; Bendas, D.; Graaf, B.; Lormans, M.; Van Solingen, R.

    2006-01-01

    Developing a software system in collaboration with other partners, and on different geographical locations is a big challenge for organizations. In this article we first discuss a system that automates build and test processes: SoftFab. This system has been successfully applied in practice in the

  17. Next Generation Catalyst Engineering via Support Modification

    Science.gov (United States)

    2016-01-21

    performance, specifically in the mass transfer region. Rotating disk electrode ( RDE ) results show that after 5000 cycles of accelerated durability...materials, combining their evaluation in RDE with SEM analysis. We have identified specific solvents and aging treatments that greatly improve the

  18. Biomedical Engineering support. Semiannual progress report

    International Nuclear Information System (INIS)

    Kolff, W.J.; Smith, L.M.; Sandquist, G.M.

    1976-01-01

    The basic goal of the ERDA Artificial Heart Program is to develop and construct an artificial heart, powered by a 238 Pu heat source, which can be successfully employed as an emplantable total artificial heart system for animal experiments. Future studies will be directed at developing and evaluating a satisfactory system for total heart replacement in humans. A total of 32 ERDA artificial hearts have been implanted since the initiation of the program. During the reporting period ten total heart replacement experiments were performed in calves using the ERDA blood pump powered by an electric motor implanted in the abdomen. Results of the experiments are given

  19. Mechanical Engineering | Classification | College of Engineering & Applied

    Science.gov (United States)

    Engineering Concentration on Ergonomics M.S. Program in Computer Science Interdisciplinary Concentration on Energy Doctoral Programs in Engineering Non-Degree Candidate Departments Biomedical Engineering Biomedical Engineering Industry Advisory Council Civil & Environmental Engineering Civil &

  20. Biomedical Engineering | Classification | College of Engineering & Applied

    Science.gov (United States)

    Engineering Concentration on Ergonomics M.S. Program in Computer Science Interdisciplinary Concentration on Energy Doctoral Programs in Engineering Non-Degree Candidate Departments Biomedical Engineering Biomedical Engineering Industry Advisory Council Civil & Environmental Engineering Civil &

  1. Materials Science & Engineering | Classification | College of Engineering &

    Science.gov (United States)

    Biomedical Engineering Concentration on Ergonomics M.S. Program in Computer Science Interdisciplinary Concentration on Energy Doctoral Programs in Engineering Non-Degree Candidate Departments Biomedical Engineering Biomedical Engineering Industry Advisory Council Civil & Environmental Engineering Civil &

  2. Electrical Engineering | Classification | College of Engineering & Applied

    Science.gov (United States)

    Engineering Concentration on Ergonomics M.S. Program in Computer Science Interdisciplinary Concentration on Energy Doctoral Programs in Engineering Non-Degree Candidate Departments Biomedical Engineering Biomedical Engineering Industry Advisory Council Civil & Environmental Engineering Civil &

  3. Engineering tribology

    CERN Document Server

    Stachowiak, Gwidon; Batchelor, A W; Batchelor, Andrew W

    2005-01-01

    As with the previous edition, the third edition of Engineering Tribology provides a thorough understanding of friction and wear using technologies such as lubrication and special materials. Tribology is a complex topic with its own terminology and specialized concepts, yet is vitally important throughout all engineering disciplines, including mechanical design, aerodynamics, fluid dynamics and biomedical engineering. This edition includes updated material on the hydrodynamic aspects of tribology as well as new advances in the field of biotribology, with a focus throughout on the engineering ap

  4. Engineering change management report 2011

    DEFF Research Database (Denmark)

    Maier, Anja; Langer, Stefan

    Changes or modifications have always been a fundamental part of product- and service design, yet they are often costly and potentially decrease overall development efficiency and effectiveness. How Danish manufacturing firms are able to improve engineering change management practice is a decisive......, challenges, and strategies for improved engineering change management of more than 90 engineering firms from different industry sectors and sizes in Denmark. In particular, the report presents an overview of current practice of engineering change management in Denmark, shows the extent to which engineering...... implementation, with software use in comparison being surprisingly low. The biggest problems listed range from engineering change process support to internal and external communication and the need for company-internal awareness and competence training for better engineering change management. The biggest need...

  5. 76 FR 44245 - Special Conditions: Gulfstream Model GVI Airplane; Limit Engine Torque Loads for Sudden Engine...

    Science.gov (United States)

    2011-07-25

    ... Conditions No. 25-441-SC] Special Conditions: Gulfstream Model GVI Airplane; Limit Engine Torque Loads for... for transport category airplanes. These design features include engine size and the potential torque... engine mounts and the supporting structures must be designed to withstand a ``limit engine torque load...

  6. NASA System Engineering Design Process

    Science.gov (United States)

    Roman, Jose

    2011-01-01

    This slide presentation reviews NASA's use of systems engineering for the complete life cycle of a project. Systems engineering is a methodical, disciplined approach for the design, realization, technical management, operations, and retirement of a system. Each phase of a NASA project is terminated with a Key decision point (KDP), which is supported by major reviews.

  7. Theoretical foundations for collaboration engineering

    NARCIS (Netherlands)

    Kolfschoten, G.L.

    2007-01-01

    Collaboration is often presented as the solution to numerous problems in business and society. However, collaboration is challenging, and collaboration support is not an off-the-shelf-product. This research offers theoretical foundations for Collaboration Engineering. Collaboration Engineering is an

  8. Space Civil Engineering option - A progress report

    Science.gov (United States)

    Criswell, Marvin E.; Sadeh, Willy Z.

    1992-01-01

    Space Civil Engineering is an emerging engineering discipline that focuses on extending and expanding Civil Engineering to the development, operation, and maintenance of infrastructures on celestial bodies. Space Civil Engineering is presently being developed as a new discipline within the Department of Civil Engineering at Colorado State University and with support of the NASA Space Grant College Program. Academic programs geared toward creating Space Civil Engineering Options at both undergraduate and graduate levels are being formulated. Basic ideas and concepts and the current status of the curriculum in the Space Civil Engineering Option primarily at the undergraduate level are presented.

  9. Heavy Truck Engine Program

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Christopher

    2009-01-08

    The Heavy Duty Truck Engine Program at Cummins embodied three significant development phases. All phases of work strove to demonstrate a high level of diesel engine efficiency in the face of increasingly stringent emission requirements. Concurrently, aftertreatment system development and refinement was pursued in support of these efficiency demonstrations. The program's first phase focused on the demonstration in-vehicle of a high level of heavy duty diesel engine efficiency (45% Brake Thermal Efficiency) at a typical cruise condition while achieving composite emissions results which met the 2004 U.S. EPA legislated standards. With a combination of engine combustion calibration tuning and the development and application of Urea-based SCR and particulate aftertreatment, these demonstrations were successfully performed by Q4 of 2002. The second phase of the program directed efforts towards an in-vehicle demonstration of an engine system capable of meeting 2007 U.S. EPA legislated emissions requirements while achieving 45% Brake Thermal Efficiency at cruise conditions. Through further combustion optimization, the refinement of Cummins Cooled EGR architecture, the application of a high pressure common rail fuel system and the incorporation of optimized engine parasitics, Cummins Inc. successfully demonstrated these deliverables in Q2 of 2004. The program's final phase set a stretch goal of demonstrating 50% Brake Thermal Efficiency from a heavy duty diesel engine system capable of meeting 2010 U.S. EPA legislated emissions requirements. Cummins chose to pursue this goal through further combustion development and refinement of the Cooled EGR system architecture and also applied a Rankine cycle Waste Heat Recovery technique to convert otherwise wasted thermal energy to useful power. The engine and heat recovery system was demonstrated to achieve 50% Brake Thermal Efficiency while operating at a torque peak condition in second quarter, 2006. The 50% efficient

  10. Food Engineering

    NARCIS (Netherlands)

    Boom, R.M.; Janssen, A.E.M.

    2014-01-01

    Food engineering is a rapidly changing discipline. Traditionally, the main focus was on food preservation and stabilization, whereas trends now are on diversity, health, taste, and sustainable production. Next to a general introduction of the definition of food engineering, this article gives a

  11. Fluids engineering

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    Fluids engineering has played an important role in many applications, from ancient flood control to the design of high-speed compact turbomachinery. New applications of fluids engineering, such as in high-technology materials processing, biotechnology, and advanced combustion systems, have kept up unwaining interest in the subject. More accurate and sophisticated computational and measurement techniques are also constantly being developed and refined. On a more fundamental level, nonlinear dynamics and chaotic behavior of fluid flow are no longer an intellectual curiosity and fluid engineers are increasingly interested in finding practical applications for these emerging sciences. Applications of fluid technology to new areas, as well as the need to improve the design and to enhance the flexibility and reliability of flow-related machines and devices will continue to spur interest in fluids engineering. The objectives of the present seminar were: to exchange current information on arts, science, and technology of fluids engineering; to promote scientific cooperation between the fluids engineering communities of both nations, and to provide an opportunity for the participants and their colleagues to explore possible joint research programs in topics of high priority and mutual interest to both countries. The Seminar provided an excellent forum for reviewing the current state and future needs of fluids engineering for the two nations. With the Seminar ear-marking the first formal scientific exchange between Korea and the United States in the area of fluids engineering, the scope was deliberately left broad and general

  12. Biomedical Engineering

    CERN Document Server

    Suh, Sang C; Tanik, Murat M

    2011-01-01

    Biomedical Engineering: Health Care Systems, Technology and Techniques is an edited volume with contributions from world experts. It provides readers with unique contributions related to current research and future healthcare systems. Practitioners and researchers focused on computer science, bioinformatics, engineering and medicine will find this book a valuable reference.

  13. Genetic Engineering

    Science.gov (United States)

    Phillips, John

    1973-01-01

    Presents a review of genetic engineering, in which the genotypes of plants and animals (including human genotypes) may be manipulated for the benefit of the human species. Discusses associated problems and solutions and provides an extensive bibliography of literature relating to genetic engineering. (JR)

  14. Corrosion Engineering.

    Science.gov (United States)

    White, Charles V.

    A description is provided for a Corrosion and Corrosion Control course offered in the Continuing Engineering Education Program at the General Motors Institute (GMI). GMI is a small cooperative engineering school of approximately 2,000 students who alternate between six-week periods of academic study and six weeks of related work experience in…

  15. Engineering Elegant Systems: Postulates, Principles, and Hypotheses of Systems Engineering

    Science.gov (United States)

    Watson, Michael D.

    2018-01-01

    Definition: System Engineering is the engineering discipline which integrates the system functions, system environment, and the engineering disciplines necessary to produce and/or operate an elegant system; Elegant System - A system that is robust in application, fully meeting specified and adumbrated intent, is well structured, and is graceful in operation. Primary Focus: System Design and Integration: Identify system couplings and interactions; Identify system uncertainties and sensitivities; Identify emergent properties; Manage the effectiveness of the system. Engineering Discipline Integration: Manage flow of information for system development and/or operations; Maintain system activities within budget and schedule. Supporting Activities: Process application and execution.

  16. Engineering surveying

    CERN Document Server

    Schofield, W

    2001-01-01

    The aim of Engineering Surveying has always been to impart and develop a clear understanding of the basic topics of the subject. The author has fully revised the book to make it the most up-to-date and relevant textbook available on the subject.The book also contains the latest information on trigonometric levelling, total stations and one-person measuring systems. A new chapter on satellites ensures a firm grasp of this vitally important topic.The text covers engineering surveying modules for civil engineering students on degree courses and forms a reference for the engineering surveying module in land surveying courses. It will also prove to be a valuable reference for practitioners.* Simple clear introduction to surveying for engineers* Explains key techniques and methods* Details reading systems and satellite position fixing

  17. Emotional engineering

    CERN Document Server

    In an age of increasing complexity, diversification and change, customers expect services that cater to their needs and to their tastes. Emotional Engineering vol 2. describes how their expectations can be satisfied and managed throughout the product life cycle, if producers focus their attention more on emotion. Emotional engineering provides the means to integrate products to create a new social framework and develops services beyond product realization to create of value across a full lifetime.  14 chapters cover a wide range of topics that can be applied to product, process and industry development, with special attention paid to the increasing importance of sensing in the age of extensive and frequent changes, including: • Multisensory stimulation and user experience  • Physiological measurement • Tactile sensation • Emotional quality management • Mental model • Kansei engineering.   Emotional Engineering vol 2 builds on Dr Fukuda’s previous book, Emotional Engineering, and provides read...

  18. Supporting information

    Indian Academy of Sciences (India)

    aDepartment of Chemistry and Chemical Engineering, Heze University, Heze, 274015, P. R. China. bDepartment of Chemistry and Chemical Engineering, Qufu Normal University, Qufu, 273165, P. R. China. cCollege of Chemistry and Chemical Engineering, Shandong University, Jinan, 250010, P. R. China. Table S1.

  19. Introduction to tissue engineering and application for cartilage engineering.

    Science.gov (United States)

    de Isla, N; Huseltein, C; Jessel, N; Pinzano, A; Decot, V; Magdalou, J; Bensoussan, D; Stoltz, J-F

    2010-01-01

    Tissue engineering is a multidisciplinary field that applies the principles of engineering, life sciences, cell and molecular biology toward the development of biological substitutes that restore, maintain, and improve tissue function. In Western Countries, tissues or cells management for clinical uses is a medical activity governed by different laws. Three general components are involved in tissue engineering: (1) reparative cells that can form a functional matrix; (2) an appropriate scaffold for transplantation and support; and (3) bioreactive molecules, such as cytokines and growth factors that will support and choreograph formation of the desired tissue. These three components may be used individually or in combination to regenerate organs or tissues. Thus the growing development of tissue engineering needs to solve four main problems: cells, engineering development, grafting and safety studies.

  20. Microwave and pulsed power engineering

    International Nuclear Information System (INIS)

    Hofer, W.W.

    1984-01-01

    The Microwave and Pulsed Power Engineering Thrust Area is responsible for developing the short-term and long-term engineering resources required to support the growing microwave and pulsed power engineering requirements of several LLNL Programs. The responsibility of this Thrust Area is to initiate applicable research and development projects and to provide capabilities and facilities to permit engineers involved in these and other programs to make significant contributions. In this section, the principal projects are described: dielectric failure prediction using partial discharge analysis, coating dielectrics to increase surface flashover potential, and the microwave generator experiment

  1. Integrating Ethics into Engineering Education

    DEFF Research Database (Denmark)

    Zhou, Chunfang; Otrel-Cass, Kathrin; Børsen, Tom

    2015-01-01

    In this chapter, the authors aim to explore the necessity of teaching ethics as part of engineering education based on the gaps between learning “hard” knowledge and “soft” skills in the current educational system. They discuss why the nature of engineering practices makes it difficult to look...... products are not value neutral. With a focus on Problem-Based Learning (PBL), the authors examine why engineers need to incorporate ethical codes in their decision-making process and professional tasks. Finally, they discuss how to build creative learning environments that can support attaining...... the objectives of engineering education....

  2. Women in science & engineering and minority engineering scholarships : year 3, report for 2008-2009 activities.

    Science.gov (United States)

    2009-05-01

    Support made scholarships available to minority and women students interested in engineering and science and significantly increased : the number of minority and female students that Missouri S&T can recruit to its science and engineering programs. R...

  3. Women in science & engineering and minority engineering scholarships : year 2 report for 2007-2008 activities.

    Science.gov (United States)

    2008-08-01

    Support will make scholarships available to minority and women students interested in engineering and science and will increase : significantly the number of minority and female students that Missouri S&T can recruit to its science and engineering pr...

  4. Mechanical engineering principles

    CERN Document Server

    Bird, John

    2014-01-01

    A student-friendly introduction to core engineering topicsThis book introduces mechanical principles and technology through examples and applications, enabling students to develop a sound understanding of both engineering principles and their use in practice. These theoretical concepts are supported by 400 fully worked problems, 700 further problems with answers, and 300 multiple-choice questions, all of which add up to give the reader a firm grounding on each topic.The new edition is up to date with the latest BTEC National specifications and can also be used on undergraduate courses in mecha

  5. Glycosylation Engineering

    DEFF Research Database (Denmark)

    Clausen, Henrik; Wandall, Hans H.; Steentoft, Catharina

    2017-01-01

    Knowledge of the cellular pathways of glycosylation across phylogeny provides opportunities for designing glycans via genetic engineering in a wide variety of cell types including bacteria, fungi, plant cells, and mammalian cells. The commercial demand for glycosylation engineering is broad......, including production of biological therapeutics with defined glycosylation (Chapter 57). This chapter describes how knowledge of glycan structures and their metabolism (Parts I–III of this book) has led to the current state of glycosylation engineering in different cell types. Perspectives for rapid...

  6. Engineering mathematics

    CERN Document Server

    Stroud, K A

    2013-01-01

    A groundbreaking and comprehensive reference that's been a bestseller since it first debuted in 1970, the new seventh edition of Engineering Mathematics has been thoroughly revised and expanded. Providing a broad mathematical survey, this innovative volume covers a full range of topics from the very basic to the advanced. Whether you're an engineer looking for a useful on-the-job reference or want to improve your mathematical skills, or you are a student who needs an in-depth self-study guide, Engineering Mathematics is sure to come in handy time and time again.

  7. Editorial: Support (November 2007

    Directory of Open Access Journals (Sweden)

    Dru Lavigne

    2007-11-01

    Full Text Available What is your first thought when you encounter the term "open source support"? A programmer typing the answer to a question using a chat utility? Hours spent scouring the Internet for a working configuration sample? Contacting a support engineer at a commercial call centre? If you find it difficult to think about a support engineer, you're not alone. Actuate's recently published 2007 Open Source Survey of senior personnel from financial services, Telco, and public sector organizations across North America and Europe indicates that 46.3% of respondents cite the lack of availability of long term support as a major barrier to their company's adoption of open source technologies.

  8. Software engineering methodologies and tools

    Science.gov (United States)

    Wilcox, Lawrence M.

    1993-01-01

    Over the years many engineering disciplines have developed, including chemical, electronic, etc. Common to all engineering disciplines is the use of rigor, models, metrics, and predefined methodologies. Recently, a new engineering discipline has appeared on the scene, called software engineering. For over thirty years computer software has been developed and the track record has not been good. Software development projects often miss schedules, are over budget, do not give the user what is wanted, and produce defects. One estimate is there are one to three defects per 1000 lines of deployed code. More and more systems are requiring larger and more complex software for support. As this requirement grows, the software development problems grow exponentially. It is believed that software quality can be improved by applying engineering principles. Another compelling reason to bring the engineering disciplines to software development is productivity. It has been estimated that productivity of producing software has only increased one to two percent a year in the last thirty years. Ironically, the computer and its software have contributed significantly to the industry-wide productivity, but computer professionals have done a poor job of using the computer to do their job. Engineering disciplines and methodologies are now emerging supported by software tools that address the problems of software development. This paper addresses some of the current software engineering methodologies as a backdrop for the general evaluation of computer assisted software engineering (CASE) tools from actual installation of and experimentation with some specific tools.

  9. Springer handbook of mechanical engineering

    Energy Technology Data Exchange (ETDEWEB)

    Grote, Karl-Heinrich [Magdeburg Univ. (Germany). Dept. of Mechanical Engineering; Antonsson, Erik K. (eds.) [California Inst. of Technology (CALTEC), Pasadena, CA (United States). Dept. of Mechanical Engineering

    2009-07-01

    Mechanical Engineering is a professional engineering discipline which involves the application of principles of physics, design, manufacturing and maintenance of mechanical systems. It requires a solid understanding of the key concepts including mechanics, kinematics, thermodynamics and energy. Mechanical engineers use these principles and others in the design and analysis of automobiles, aircrafts, heating and cooling systems, industrial equipment and machinery. In addition to these main areas, specialized fields are necessary to prepare future engineers for their positions in industry, such as mechatronics and robotics, transportation and logistics, fuel technology, automotive engineering, biomechanics, vibration, optics and others. Accordingly, the Springer Handbook of Mechanical Engineering devotes its contents to all areas of interest for the practicing engineer as well as for the student at various levels and educational institutions. Authors from all over the world have contributed with their expertise and support the globally working engineer in finding a solution for today's mechanical engineering problems. Each subject is discussed in detail and supported by numerous figures and tables. DIN standards are retained throughout and ISO equivalents are given where possible. The text offers a concise but detailed and authoritative treatment of the topics with full references. (orig.)

  10. Adaptive Collaboration Support Systems : Designing Collaboration Support for Dynamic Environments

    NARCIS (Netherlands)

    Janeiro, J.; Knoll, S.W.; Lukosch, S.G.; Kolfschoten, G.L.

    2012-01-01

    Today, engineering systems offer a variety of local and webbased applications to support collaboration by assisting groups in structuring activities, generating and sharing data, and improving group communication. To ensure the quality of collaboration, engineering system design needs to analyze and

  11. Knowledge Expansion in Engineering Education: Engineering Technology as an Alternative

    Directory of Open Access Journals (Sweden)

    Kamsiah Mohd Ismail

    2015-07-01

    Full Text Available Abstract. The current and rising challenges in engineering education demand graduate engineers who are well-prepared to provide innovative solutions as technical specialists, system integrators and change agents. Realizing the importance of producing a highly competent manpower, the Malaysian Government has put considerable pressure to the universities to produce engineers who are competitive in the global market. Hence, this assignment of developing a highly competence engineering technologist workforce in support of the government policy highlights issues pertaining to the development and offering of practical-oriented programs as a knowledge expansion in engineering education at universities as envisioned by the Malaysian Government.  This paper evaluates the current scenario and examines the application-oriented programs of engineering technology education as practice in local institutions in Malaysia in comparisons to some universities abroad. It also investigates the challenges faced by university management in dealing with issues concerning national quality assurance and accreditation pertaining to the engineering technology education programs. Specifically, it analyzes the faculty planning of pedagogies in term of hands-on skills in teaching and learning. A key conclusion of this research is that Malaysian universities need to evaluate its engineering technology education strategies if they aim for quality assurance and accreditation to be established and aspire for successful attempts towards the creation of the requisite knowledge workers that Malaysia needs.Keywords: application-oriented, engineering education, engineering technology, hands-on skills, knowledge expansion 

  12. B 150 civil engineering futures

    DEFF Research Database (Denmark)

    Foreword B150 –Civil Engineering Futures consists of interviews made, articles written, and projects presented in connection with the 150th anniversary celebrations of the study of civil engineering in Denmark. Instead of a historical retrospect, it was decided to look into the future. What...... challenges will the next 150 years bring civil engineers? Researchers and lecturers at DTU’s Department of Civil Engineering (known as DTU Byg) suggested possible events, and we also consulted civil engineers and their business partners in the building industry. In this way, a programme was put together...... theme in twentieth century architecture. Together, civil engineer Peter Rice and architect Ian Ritchie created a paradigm shift with their revolutionary ideas for glass facades supported by cables. Glued and bolted constructions made entirely of glass are now a reality in small-scale projects, yet...

  13. Some developing concepts of engineering education

    Science.gov (United States)

    Perkins, C. D.

    1975-01-01

    An analysis of the circumstances which have created a shortage of aeronautical engineering undergraduate students in the universities is presented. Suggestions for motivating students to enter aeronautical engineering are examined. The support of the aeronautical industry for graduate education funding is recommended. Examples of actions taken by governmental agencies to promote increased interest in aeronautical engineering are included.

  14. Engineering Design of KSTAR tokamak main structure

    International Nuclear Information System (INIS)

    Im, K.H.; Cho, S.; Her, N.I.

    2001-01-01

    The main components of the KSTAR (Korea Superconducting Tokamak Advanced Research) tokamak including vacuum vessel, plasma facing components, cryostat, thermal shield and magnet supporting structure are in the final stage of engineering design. Hundai Heavy Industries (HHI) has been involved in the engineering design of these components. The current configuration and the final engineering design results for the KSTAR main structure are presented. (author)

  15. SNF project engineering process improvement plan

    International Nuclear Information System (INIS)

    DESAI, S.P.

    1999-01-01

    This Engineering Process Improvement Plan documents the activities and plans to be taken by the SNF Project to support its engineering process and to produce a consolidated set of engineering procedures that are fully compliant with the requirements of HNF-PRO-1819. All new procedures will be issued and implemented by September 30, 1999

  16. Software engineering

    CERN Document Server

    Sommerville, Ian

    2016-01-01

    For courses in computer science and software engineering The Fundamental Practice of Software Engineering Software Engineering introduces readers to the overwhelmingly important subject of software programming and development. In the past few years, computer systems have come to dominate not just our technological growth, but the foundations of our world's major industries. This text seeks to lay out the fundamental concepts of this huge and continually growing subject area in a clear and comprehensive manner. The Tenth Edition contains new information that highlights various technological updates of recent years, providing readers with highly relevant and current information. Sommerville's experience in system dependability and systems engineering guides the text through a traditional plan-based approach that incorporates some novel agile methods. The text strives to teach the innovators of tomorrow how to create software that will make our world a better, safer, and more advanced place to live.

  17. Harmonic engine

    Science.gov (United States)

    Bennett, Charles L [Livermore, CA

    2009-10-20

    A high efficiency harmonic engine based on a resonantly reciprocating piston expander that extracts work from heat and pressurizes working fluid in a reciprocating piston compressor. The engine preferably includes harmonic oscillator valves capable of oscillating at a resonant frequency for controlling the flow of working fluid into and out of the expander, and also preferably includes a shunt line connecting an expansion chamber of the expander to a buffer chamber of the expander for minimizing pressure variations in the fluidic circuit of the engine. The engine is especially designed to operate with very high temperature input to the expander and very low temperature input to the compressor, to produce very high thermal conversion efficiency.

  18. Engineering personnel

    International Nuclear Information System (INIS)

    Paskievici, W.

    The expansion of nuclear power is taxing human, material, and capital resources in developed and developing countries. This paper explores the human resources as represented by employment, graduation statistics, and educational curricula for nuclear engineers. (E.C.B.)

  19. Green Engineering

    Science.gov (United States)

    Green Engineering is the design, commercialization and use of processes and products that are feasible and economical while reducing the generation of pollution at the source and minimizing the risk to human health and the environment.

  20. Coastal Engineering

    NARCIS (Netherlands)

    Van der Velden, E.T.J.M.

    1989-01-01

    Introduction, waves, sediment transport, littoral transport, lonshore sediment transport, onshore-offshore sediment transport, coastal changes, dune erosion and storm surges, sedimentation in channels and trenches, coastal engineering in practice.

  1. Geoenvironmental engineering

    International Nuclear Information System (INIS)

    Shin, Eun Cheol; Park, Jeong Jun

    2009-08-01

    This book deals with definition of soil and scope of clean-up of soil, trend of geoenvironmental engineering at home and foreign countries, main concern of geoenvironmental engineering in domestic and abroad, design and building of landfills such as summary, trend of landfill policy in Korea, post management of landfill facilities, stabilizing and stability of landfill, research method and soil pollution source, restoration technology of soil pollution like restoration technique of oil pollution with thermal processing.

  2. Microwave engineering

    CERN Document Server

    Pozar, David M

    2012-01-01

    The 4th edition of this classic text provides a thorough coverage of RF and microwave engineering concepts, starting from fundamental principles of electrical engineering, with applications to microwave circuits and devices of practical importance.  Coverage includes microwave network analysis, impedance matching, directional couplers and hybrids, microwave filters, ferrite devices, noise, nonlinear effects, and the design of microwave oscillators, amplifiers, and mixers. Material on microwave and RF systems includes wireless communications, radar, radiometry, and radiation hazards. A large

  3. Reliability Engineering

    International Nuclear Information System (INIS)

    Lee, Sang Yong

    1992-07-01

    This book is about reliability engineering, which describes definition and importance of reliability, development of reliability engineering, failure rate and failure probability density function about types of it, CFR and index distribution, IFR and normal distribution and Weibull distribution, maintainability and movability, reliability test and reliability assumption in index distribution type, normal distribution type and Weibull distribution type, reliability sampling test, reliability of system, design of reliability and functionality failure analysis by FTA.

  4. Systems Engineering

    OpenAIRE

    Vaughan, William W.

    2016-01-01

    The term “systems engineering” when entered into the Google search page, produces a significant number of results, evidence that systems engineering is recognized as being important for the success of essentially all products. Since most readers of this item will be rather well versed in documents concerning systems engineering, I have elected to share some of the points made on this subject in a document developed by the European Cooperation for Space Standardization (ECSS), a component of t...

  5. Software Engineering Improvement Plan

    Science.gov (United States)

    2006-01-01

    In performance of this task order, bd Systems personnel provided support to the Flight Software Branch and the Software Working Group through multiple tasks related to software engineering improvement and to activities of the independent Technical Authority (iTA) Discipline Technical Warrant Holder (DTWH) for software engineering. To ensure that the products, comments, and recommendations complied with customer requirements and the statement of work, bd Systems personnel maintained close coordination with the customer. These personnel performed work in areas such as update of agency requirements and directives database, software effort estimation, software problem reports, a web-based process asset library, miscellaneous documentation review, software system requirements, issue tracking software survey, systems engineering NPR, and project-related reviews. This report contains a summary of the work performed and the accomplishments in each of these areas.

  6. Energy production systems engineering

    CERN Document Server

    Blair, Thomas Howard

    2017-01-01

    Energy Production Systems Engineering presents IEEE, Electrical Apparatus Service Association (EASA), and International Electrotechnical Commission (IEC) standards of engineering systems and equipment in utility electric generation stations. Electrical engineers that practice in the energy industry must understand the specific characteristics of electrical and mechanical equipment commonly applied to energy production and conversion processes, including the mechanical and chemical processes involved, in order to design, operate and maintain electrical systems that support and enable these processes. To aid this understanding, Energy Production Systems Engineeringdescribes the equipment and systems found in various types of utility electric generation stations. This information is accompanied by examples and practice problems. It also addresses common issues of electrical safety that arise in electric generation stations.

  7. Systems engineering management plan

    International Nuclear Information System (INIS)

    Conner, C.W.

    1985-10-01

    The purpose of this Systems Engineering Management Plan (SEMP) is to prescribe the systems engineering procedures to be implemented at the Program level and the minimum requirements for systems engineering at the Program-element level. The Program level corresponds to the Director, OCRWM, or to the organizations within OCRWM to which the Director delegates responsibility for the development of the System and for coordinating and integrating the activities at the Program-element level. The Office of Policy and Outreach (OPO) and the Office of Resource Management (ORM) support the Director at the Program level. The Program-element level corresponds to the organizations within OCRWM (i.e., the Office of Geologic Repositories (OGR) and the Office of Storage and Transportation Systems (OSTS)) with overall responsibility for developing the System elements - that is, the mined geologic disposal system (MGDS), monitored retrievable storage (MRS) (if approved by Congress), and the transportation system

  8. Aircraft Wiring Support Equipment Integration Laboratory (AWSEIL)

    Data.gov (United States)

    Federal Laboratory Consortium — Purpose:The Aircraft Wiring Support Equipment Integration Laboratory (AWSEIL) provides a variety of research, design engineering and prototype fabrication services...

  9. Fleet Aviation Maintenance Organic Support (FAMOS) Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — Purpose:The Fleet Aviation Maintenance Organic Support (FAMOS) Laboratory at the Naval Air Warfare Center Aircraft Division, Lakehurst, NJ provides rapid engineering...

  10. Hire a Milwaukee Engineer | College of Engineering & Applied Science

    Science.gov (United States)

    Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

  11. Security Engineering FY17 Systems Aware Cybersecurity

    Science.gov (United States)

    2017-12-07

    Security Engineering – FY17 Systems Aware Cybersecurity Technical Report SERC-2017-TR-114 December 7 2017 Principal Investigator: Dr...December 7, 2017 Copyright © 2017 Stevens Institute of Technology, Systems Engineering Research Center The Systems Engineering Research Center (SERC...supported, in whole or in part, by the U.S. Department of Defense through the Office of the Assistant Secretary of Defense for Research and Engineering (ASD

  12. Nuclear industry will be short of engineers

    International Nuclear Information System (INIS)

    Yates, M.

    1990-01-01

    This article discusses the potential shortage of nuclear engineers due to reduction of educational and training facilities and difficulty in attracting minorities into nuclear engineering. The article reports on recommendations from the National Research Council Nuclear Education Study Committee on attracting minorities to nuclear engineering, increasing DOE fellowships, funding for research and development, involvement of utilities and vendors, and support of the American Nuclear Society's advocacy of nuclear engineering education

  13. Solar-Thermal Engine Testing

    Science.gov (United States)

    Tucker, Stephen; Salvail, Pat; Haynes, Davy (Technical Monitor)

    2001-01-01

    A solar-thermal engine serves as a high-temperature solar-radiation absorber, heat exchanger, and rocket nozzle. collecting concentrated solar radiation into an absorber cavity and transferring this energy to a propellant as heat. Propellant gas can be heated to temperatures approaching 4,500 F and expanded in a rocket nozzle, creating low thrust with a high specific impulse (I(sub sp)). The Shooting Star Experiment (SSE) solar-thermal engine is made of 100 percent chemical vapor deposited (CVD) rhenium. The engine 'module' consists of an engine assembly, propellant feedline, engine support structure, thermal insulation, and instrumentation. Engine thermal performance tests consist of a series of high-temperature thermal cycles intended to characterize the propulsive performance of the engines and the thermal effectiveness of the engine support structure and insulation system. A silicone-carbide electrical resistance heater, placed inside the inner shell, substitutes for solar radiation and heats the engine. Although the preferred propellant is hydrogen, the propellant used in these tests is gaseous nitrogen. Because rhenium oxidizes at elevated temperatures, the tests are performed in a vacuum chamber. Test data will include transient and steady state temperatures on selected engine surfaces, propellant pressures and flow rates, and engine thrust levels. The engine propellant-feed system is designed to Supply GN2 to the engine at a constant inlet pressure of 60 psia, producing a near-constant thrust of 1.0 lb. Gaseous hydrogen will be used in subsequent tests. The propellant flow rate decreases with increasing propellant temperature, while maintaining constant thrust, increasing engine I(sub sp). In conjunction with analytical models of the heat exchanger, the temperature data will provide insight into the effectiveness of the insulation system, the structural support system, and the overall engine performance. These tests also provide experience on operational

  14. Rethinking engineering education the CDIO approach

    CERN Document Server

    Crawley, Edward F; Östlund, Sören; Brodeur, Doris R; Edström, Kristina

    2014-01-01

    This book describes an approach to engineering education that integrates a comprehensive set of personal, interpersonal, and professional engineering skills with engineering disciplinary knowledge in order to prepare innovative and entrepreneurial engineers.  The education of engineers is set in the context of engineering practice, that is, Conceiving, Designing, Implementing, and Operating (CDIO) through the entire lifecycle of engineering processes, products, and systems. The book is both a description of the development and implementation of the CDIO model and a guide to engineering programs worldwide that seek to improve the education of young engineers.   Provides an overview of the CDIO approach, then chapters organized according to the CDIO Standards; Includes in each chapter objectives, discussion questions, case studies and clear diagrams to support key concepts and processes; Avoids the jargon of education specialists and clearly explains education terms in the context of their initial presentatio...

  15. Conference Modern Engineering : Science and Education

    CERN Document Server

    2017-01-01

    This book draws together the most interesting recent results to emerge in mechanical engineering in Russia, providing a fascinating overview of the state of the art in the field in that country which will be of interest to a wide readership. A broad range of topics and issues in modern engineering are discussed, including dynamics of machines, materials engineering, structural strength and tribological behavior, transport technologies, machinery quality and innovations. The book comprises selected papers presented at the conference "Modern Engineering: Science and Education", held at the Saint Petersburg State Polytechnic University in 2016 with the support of the Russian Engineering Union. The authors are experts in various fields of engineering, and all of the papers have been carefully reviewed. The book will be of interest to mechanical engineers, lecturers in engineering disciplines and engineering graduates.

  16. A nuclear power plant system engineering workstation

    International Nuclear Information System (INIS)

    Mason, J.H.; Crosby, J.W.

    1989-01-01

    System engineers offer an approach for effective technical support for operation and maintenance of nuclear power plants. System engineer groups are being set up by most utilities in the United States. Institute of Nuclear Power operations (INPO) and U.S. Nuclear Regulatory Commission (NRC) have endorsed the concept. The INPO Good Practice and a survey of system engineer programs in the southeastern United States provide descriptions of system engineering programs. The purpose of this paper is to describe a process for developing a design for a department-level information network of workstations for system engineering groups. The process includes the following: (1) application of a formal information engineering methodology, (2) analysis of system engineer functions and activities; (3) use of Electric Power Research Institute (EPRI) Plant Information Network (PIN) data; (4) application of the Information Engineering Workbench. The resulting design for this system engineer workstation can provide a reference for design of plant-specific systems

  17. Engineering physics

    CERN Document Server

    Mukherji, Uma

    2015-01-01

    ENGINEERING PHYSICS is designed as a textbook for first year engineering students of a two semester course in Applied Physics according to new revised syllabus. However the scope of this book is not only limited to undergraduate engineering students and science students, it can also serve as a reference book for practicing scientists.Advanced technological topics like LCD, Squid, Maglev system, Electron microscopes, MRI, Photonics - Photonic fibre, Nano-particles, CNT, Quantum computing etc., are explained with basic underlying principles of Physics.This text explained following topics with numerous solved, unsolved problems and questions from different angles. Part-I contains crystal structure, Liquid crystal, Thermo-electric effect, Thermionic emission, Ultrasonic, Acoustics, semiconductor and magnetic materials. Whereas Part-2 contains Optics, X-rays, Electron optics, Dielectric materials, Quantum Physics and Schrodinger wave equation, Laser, Fibre-optics and Holography, Radio-activity, Super-conductivity,...

  18. Music engineering

    CERN Document Server

    Brice, Richard

    2001-01-01

    Music Engineering is a hands-on guide to the practical aspects of electric and electronic music. It is both a compelling read and an essential reference guide for anyone using, choosing, designing or studying the technology of modern music. The technology and underpinning science are introduced through the real life demands of playing and recording, and illustrated with references to well known classic recordings to show how a particular effect is obtained thanks to the ingenuity of the engineer as well as the musician. In addition, an accompanying companion website containing over 50 specially chosen tracks for download, provides practical demonstrations of the effects and techniques described in the book. Written by a music enthusiast and electronic engineer, this book covers the electronics and physics of the subject as well as the more subjective aspects. The second edition includes an updated Digital section including MPEG3 and fact sheets at the end of each chapter to summarise the key electronics and s...

  19. Engineering surveying

    CERN Document Server

    Schofield, W

    2007-01-01

    Engineering surveying involves determining the position of natural and man-made features on or beneath the Earth's surface and utilizing these features in the planning, design and construction of works. It is a critical part of any engineering project. Without an accurate understanding of the size, shape and nature of the site the project risks expensive and time-consuming errors or even catastrophic failure.Engineering Surveying 6th edition covers all the basic principles and practice of this complex subject and the authors bring expertise and clarity. Previous editions of this classic text have given readers a clear understanding of fundamentals such as vertical control, distance, angles and position right through to the most modern technologies, and this fully updated edition continues that tradition.This sixth edition includes:* An introduction to geodesy to facilitate greater understanding of satellite systems* A fully updated chapter on GPS, GLONASS and GALILEO for satellite positioning in surveying* Al...

  20. Engineering Optics

    CERN Document Server

    Iizuka, Keigo

    2008-01-01

    Engineering Optics is a book for students who want to apply their knowledge of optics to engineering problems, as well as for engineering students who want to acquire the basic principles of optics. It covers such important topics as optical signal processing, holography, tomography, holographic radars, fiber optical communication, electro- and acousto-optic devices, and integrated optics (including optical bistability). As a basis for understanding these topics, the first few chapters give easy-to-follow explanations of diffraction theory, Fourier transforms, and geometrical optics. Practical examples, such as the video disk, the Fresnel zone plate, and many more, appear throughout the text, together with numerous solved exercises. There is an entirely new section in this updated edition on 3-D imaging.