WorldWideScience

Sample records for superpolished metal mirrors

  1. Lightweight Metal Mirrors

    Science.gov (United States)

    Gossett, E.; Winslow, P.

    1984-01-01

    Two "eggcrate" halves brazed together. Lightweight flat mirrors fabricated by machining pockets in two plates of beryllium and brazing machined halves together. Mirror less than half weight of same mirror made by previous design.

  2. Achievement of a superpolish on bare stainless steel

    Science.gov (United States)

    Howells, Malcolm R.; Casstevens, John M.

    1997-11-01

    We report the achievement of a superpolished surface, suitable for x-ray reflection, on bare stainless steel. The rms roughness obtained on various samples varied from 2.2 to 4.2 angstroms, as measured by an optical profiler with a bandwidth 0.29 - 100 mm-1. The type 17-4 PH precipitation-hardening stainless steel used to make the mirrors is also capable of ultrastability and has good manufacturability. This combination of properties makes it an excellent candidate material for mirror substrates. We describe the successful utilization of this type of steel in making elliptical-cylinder mirrors for a soft-x-ray microprobe system at the Advanced Light Source, and discuss possible reasons for its unusual stability and polishability.

  3. Metals in Metal Salts: A Copper Mirror Demonstration

    Science.gov (United States)

    Pike, Robert D.

    2010-01-01

    A simple lecture demonstration is described to show the latent presence of metal atoms in a metal salt. Copper(II) formate tetrahydrate is heated in a round-bottom flask forming a high-quality copper mirror.

  4. Super Polishing of Aluminum 6061-T6 Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — An innovative 2D super-polishing process for Aluminum 6061-T6 planar mirrors which removes diamond point turning (DPT) grooves and attains rms surface finishes below...

  5. Low-Stress Silicon Cladding for Surface Finishing Large UVOIR Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this Phase I research, ZeCoat Corporation will develop an affordable, low-stress silicon cladding process which is super-polishable for large UVOIR mirrors. The...

  6. Polishing Metal Mirrors to 0,025 Micron Surface Finish

    DEFF Research Database (Denmark)

    Pedersen, P. E.

    1978-01-01

    A research program undertaken by the Danish Atomic Energy Commission required the fabrication of metal mirrors measuring 1 m long by 53 mm wide, which had to be finished to extremely tight tolerances on thickness, plane-parallelism and surface characteristics. Progressively finer diamond compounds...

  7. Dispersive mirrors designed with mixed metal multilayer dielectric stacks

    Institute of Scientific and Technical Information of China (English)

    Jinlong Zhang; Zhanshan Wang; Xinbin Cheng

    2012-01-01

    A different approach to construct dispersive mirrors (DMs) for ultrafast applications is proposed based on the high reflectivity and constant phase property of a novel metal in ultrawide spectral band.A 200-nm bandwidth DM,a high dispersive DM,and a complementary DM are designed with mixed metal multilayer dielectric stacks.The results show that the mixed-metal multilayer dielectric DMs (MMDMs)have much less layers and total thickness compared with an all-dielectric DM under the case of comparable performance.Such an approach will save manufacturing time and remarkably improve the stress of the DM.

  8. Ancient Metal Mirror Alloy Revisited: Quasicrystalline Nanoparticles Observed

    Science.gov (United States)

    Sekhar, J. A.; Mantri, A. S.; Yamjala, S.; Saha, Sabyasachi; Balamuralikrishnan, R.; Rao, P. Rama

    2015-12-01

    This article presents, for the first time, evidence of nanocrystalline structure, through direct transmission electron microscopy (TEM) observations, in a Cu-32 wt.% Sn alloy that has been made by an age-old, uniquely crafted casting process. This alloy has been used as a metal mirror for centuries. The TEM images also reveal five-sided projections of nano-particles. The convergent beam nano-diffraction patterns obtained from the nano-particles point to the nano-phase being quasicrystalline, a feature that has never before been reported for a copper alloy, although there have been reports of the presence of icosahedral `clusters' within large unit cell intermetallic phases. This observation has been substantiated by x-ray diffraction, wherein the observed peaks could be indexed to an icosahedral quasi-crystalline phase. The mirror alloy casting has been valued for its high hardness and high reflectance properties, both of which result from its unique internal microstructure that include nano-grains as well as quasi-crystallinity. We further postulate that this microstructure is a consequence of the raw materials used and the manufacturing process, including the choice of mold material. While the alloy consists primarily of copper and tin, impurity elements such as zinc, iron, sulfur, aluminum and nickel are also present, in individual amounts not exceeding one wt.%. It is believed that these trace impurities could have influenced the microstructure and, consequently, the properties of the metal mirror alloy.

  9. Reflective metallic coatings for first mirrors on ITER

    Energy Technology Data Exchange (ETDEWEB)

    Eren, Baran, E-mail: baran.eren@unibas.ch [Department of Physics, University of Basel, Klingelbergstrasse 82, CH-4056 Basel (Switzerland); Marot, Laurent [Department of Physics, University of Basel, Klingelbergstrasse 82, CH-4056 Basel (Switzerland); Litnovsky, Andrey; Matveeva, Maria [Institut fuer Energieforschung (Plasmaphysik), Forschungszentrum Juelich, Association EURATOM-FZJ, D 52425 Juelich (Germany); Steiner, Roland; Emberger, Valentin; Wisse, Marco [Department of Physics, University of Basel, Klingelbergstrasse 82, CH-4056 Basel (Switzerland); Mathys, Daniel [Centre of Microscopy, University of Basel, Klingelbergstrasse 50/70, CH-4056 Basel (Switzerland); Covarel, Gregory [Laboratoire de Physique et Mecanique Textile EA CNRS 7189, Universite de Haute Alsace, 61 rue Albert Camus, 68093 Mulhouse Cedex (France); Meyer, Ernst [Department of Physics, University of Basel, Klingelbergstrasse 82, CH-4056 Basel (Switzerland)

    2011-10-15

    Metallic mirrors are foreseen to play a crucial role for all optical diagnostics in ITER. Therefore, the development of reliable techniques for the production of mirrors which are able to maintain their optical properties in the harsh ITER environment is highly important. By applying magnetron sputtering and evaporation techniques, rhodium and molybdenum films have been prepared for tokamak tests. The films were characterised in terms of chemical composition, surface roughness, crystallite structure, reflectivity and adhesion. No impurities were detected on the surface after deposition. The effects of deposition parameters and substrate temperature on the resulting crystallite structure, surface roughness and hence on the reflectivity, were investigated. The films are found to exhibit nanometric crystallites with a dense columnar structure. Open boundaries between the crystallite columns, which are sometimes present after evaporation, are found to reduce the reflectivity as compared to rhodium or molybdenum references.

  10. Mirroring

    DEFF Research Database (Denmark)

    Wegener, Gregers

    2016-01-01

    and metaphorical value of mirroring for creativity theory across two different research fields — neuroscience and learning. We engage in a mutual (possibly creative) exploration of mirroring from ‘mirror neurons’ to mirroring in social learning theory. One of the most fascinating aspects of mirroring......Most definitions of creativity emphasise originality. The creative product is recognised as distinct from other products and the creative person as someone who stands out from the crowd. What tend to be overlooked are acts of mirroring as a crucial element of the creative process. The human ability...... to empathise and socialise is partly due to another, more fundamental ability to duplicate the stance of the other (see also Chapter 13). Through mirroring, we attune to other people and thus create resonance and preparedness for mutual creative exploration. In this chapter, we investigate the object...

  11. Specular and non-specular X-ray reflection from a single-crystal molybdenum mirror surface

    CERN Document Server

    Mizusawa, M

    2003-01-01

    The surface morphology of a super-polished mirror of single-crystal molybdenum has been studied by grazing-incidence X-ray reflection. It yields a rather high specular reflectivity (82.0%) for 16.0 keV X-rays below the critical angle. The data suggest that the mirror has a small roughness (0.7 nm rms) unlike other metal mirrors, but, on the other hand, strongly damaged layers (6.35 nm in total) exist at the near surface. It has been also found that the surface has a large correlation length (>3 mu m) and a small Hurst parameter (0.2-0.3) from the non-specular reflection.

  12. Ames Research Center cryogenic mirror testing program - A comparison of the cryogenic performance of metal and glass mirrors with different types of mounts

    Science.gov (United States)

    Miller, Jacob H.; Melugin, Ramsey K.; Augason, Gordon C.; Howard, Steven D.; Pryor, G. Mark

    1989-01-01

    A summary of the cryogenic testing of glass and metal mirrors performed at NASA Ames Research Center (ARC) and two other places is presented. Recent improvements to the ARC Cryogenic Optics Test Facility are described. The purposes of the tests were to determine: (1) how glass mirrors would perform at cryogenic temperatures compared with metal mirrors and (2) how various mirror mounts would affect the cryogenic performance of mirrors. Details of a cryogenic test of a 50 cm 'double arch', fused-silica mirror with a three-point mount and with a radially-compliant, flexured mount are given. Within the accuracy of the measurements, it was determined that the flexured mount did not induce appreciable distortion in the double arch mirror. Results of the cryogenic tests of a number of glass mirrors and two beryllium mirrors are included. The cryogenic distortion of the glass mirrors was found to be less than that for the beryllium mirrors. Within the accuracy of the measurements, no hysteresis was found in the glass mirrors. It was possible to measure hysteresis in one of the beryllium mirrors.

  13. Design of Optical Metamaterial Mirror with Metallic Nanoparticles for Broadband Light Absorption in Graphene Optoelectronic Devices

    CERN Document Server

    Lee, Seungwoo

    2015-01-01

    A general metallic mirror (i.e., a flat metallic surface) has been a popular optical component that can contribute broadband light absorption to thin-film optoelectronic devices; nonetheless, such electric mirror with a reversal of reflection phase inevitably causes the problem of minimized electric field near at the mirror surface (maximized electric field at one quarter of wavelength from mirror). This problem becomes more elucidated, when the deep-subwavelength-scaled two-dimensional (2D) material (e.g., graphene and molybdenum disulfide) is implemented into optoelectronic device as an active channel layer. The purpose of this work was to conceive the idea for using a charge storage layer (spherical Au nanoparticles (AuNPs), embedded into dielectric matrix) of the floating-gate graphene photodetector as a magnetic mirror, which allows the device to harness the increase in broadband light absorption. In particular, we systematically examined whether the versatile assembly of spherical AuNP monolayer within ...

  14. Metal hydride switchable mirrors: Factors influencing dynamic range and stability

    Energy Technology Data Exchange (ETDEWEB)

    Slack, Jonathan L.; Locke, James C.W.; Song, Seung-Wan; Ona, Jason; Richardson, Thomas J. [Lawrence Berkeley National Laboratory, Building Technologies Department, Environmental Energy Technologies Division, Berkeley, CA 94720 (United States)

    2006-03-06

    Palladium-coated magnesium-manganese-nickel films behave as gasochromic switchable mirrors, becoming transparent on exposure to dilute hydrogen, and reverting to a mirror state on exposure to air. The cycling stability of the optical switching depends upon preservation of the integrity of the Pd catalyst overlayer. Alloying between Mg and Pd causes interdiffusion of the two elements, and leads to degradation in switching speed and eventual deactivation. Incorporation of a thin niobium oxide barrier layer between the active magnesium alloy film and the Pd layer substantially improves the cycling stability of the mirror. (author)

  15. Low Cost Very Large Diamond Turned Metal Mirror Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Electrolytic plating of high phosphorus nickel phosphorus alloy will encapsulate a machined mirror substrate master made of fine cell plastic foam such as...

  16. Figure correction of a metallic ellipsoidal neutron focusing mirror

    Science.gov (United States)

    Guo, Jiang; Yamagata, Yutaka; Morita, Shin-ya; Takeda, Shin; Kato, Jun-ichi; Hino, Masahiro; Furusaka, Michihiro

    2015-06-01

    An increasing number of neutron focusing mirrors is being adopted in neutron scattering experiments in order to provide high fluxes at sample positions, reduce measurement time, and/or increase statistical reliability. To realize a small focusing spot and high beam intensity, mirrors with both high form accuracy and low surface roughness are required. To achieve this, we propose a new figure correction technique to fabricate a two-dimensional neutron focusing mirror made with electroless nickel-phosphorus (NiP) by effectively combining ultraprecision shaper cutting and fine polishing. An arc envelope shaper cutting method is introduced to generate high form accuracy, while a fine polishing method, in which the material is removed effectively without losing profile accuracy, is developed to reduce the surface roughness of the mirror. High form accuracy in the minor-axis and the major-axis is obtained through tool profile error compensation and corrective polishing, respectively, and low surface roughness is acquired under a low polishing load. As a result, an ellipsoidal neutron focusing mirror is successfully fabricated with high form accuracy of 0.5 μm peak-to-valley and low surface roughness of 0.2 nm root-mean-square.

  17. Figure correction of a metallic ellipsoidal neutron focusing mirror

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Jiang, E-mail: jiang.guo@riken.jp; Yamagata, Yutaka; Morita, Shin-ya; Kato, Jun-ichi [Ultrahigh Precision Optics Technology Team, RIKEN Center for Advanced Photonics (RAP), RIKEN, Wako, Saitama 351-0198 (Japan); Takeda, Shin [Ultrahigh Precision Optics Technology Team, RIKEN Center for Advanced Photonics (RAP), RIKEN, Wako, Saitama 351-0198 (Japan); Graduate School of Engineering, Hokkaido University, Sapporo, Hokkaido 060-0808 (Japan); Hino, Masahiro [Neutron Optics Group, Research Reactor Institute, Kyoto University, Kumatori, Osaka 590-0494 (Japan); Furusaka, Michihiro [Graduate School of Engineering, Hokkaido University, Sapporo, Hokkaido 060-0808 (Japan)

    2015-06-15

    An increasing number of neutron focusing mirrors is being adopted in neutron scattering experiments in order to provide high fluxes at sample positions, reduce measurement time, and/or increase statistical reliability. To realize a small focusing spot and high beam intensity, mirrors with both high form accuracy and low surface roughness are required. To achieve this, we propose a new figure correction technique to fabricate a two-dimensional neutron focusing mirror made with electroless nickel-phosphorus (NiP) by effectively combining ultraprecision shaper cutting and fine polishing. An arc envelope shaper cutting method is introduced to generate high form accuracy, while a fine polishing method, in which the material is removed effectively without losing profile accuracy, is developed to reduce the surface roughness of the mirror. High form accuracy in the minor-axis and the major-axis is obtained through tool profile error compensation and corrective polishing, respectively, and low surface roughness is acquired under a low polishing load. As a result, an ellipsoidal neutron focusing mirror is successfully fabricated with high form accuracy of 0.5 μm peak-to-valley and low surface roughness of 0.2 nm root-mean-square.

  18. Chemical vapor deposition of silicon carbide for large area mirrors

    Science.gov (United States)

    Gentilman, R. L.; Maguire, E. A.

    1982-05-01

    CVD-SiC has been identified as the leading mirror material for high energy synchrotron radiation because of its high K/alpha ratio and its ability to be super-polished to less than or equal to 10 A rms roughness. Technology already exists for depositing SiC over large areas (approximately 70 cm x 20 cm). The CVD process, substrate selection, and mirror design considerations are discussed.

  19. Fabrication and Testing of Active and Adaptive Cyanate Ester Composite Mirrors

    Science.gov (United States)

    Bennett, H. E.

    2004-01-01

    The objective of the NASA/Bennett Optical Research Inc. (BOR) NAS8-02008 Phase II Program, which also incorporated ideas developed under the earlier NASA NAS8-01035 Phase 1 Program, was to develop a large mirror fabrication and test facility with emphasis on producing large, light weight active and adaptive optics. A principle objective was to develop mandrels on which to make large composite graphite-filled cyanate ester mirrors, Deliverables were two of these superpolished lightweight active/adaptive optic composite mirrors, one 12" (approx.1/3 meter) in diameter and one 22" (approx.1/2 meter) in diameter. In addition optical superpolishers for mandrels up to 1.2 meters in diameter, test instruments for determining optical figure and scattered light, novel design actuators for making the composite mirrors both active and adaptive, and passive and active means for measuring actuator performance were developed at BOR. We are now installing a superpolisher capable of producing 3 meter diameter mirror/mandrels. All polishers utilize the principle of centrifugal elutriation and produce superpolished mandrels with surface microroughnesses under 1 nm rms.

  20. Hidden photon dark matter search with large metallic mirror

    Energy Technology Data Exchange (ETDEWEB)

    Doebrich, Babette; Lindner, Axel [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Daumiller, Kai; Engel, Ralph; Roth, Markus [Karlsruher Institut fuer Technologie (KIT), Karlsruhe (Germany); Kowalski, Marek [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Humboldt-Universitaet, Berlin (Germany). Inst. fuer Physik; Redondo, Javier [Zaragoza Univ. (Spain)

    2014-10-15

    If Dark Matter is composed of hidden-sector photons that kinetically mix with photons of the visible sector, then Dark Matter has a tiny oscillating electric field component. Its presence would lead to a small amount of visible radiation being emitted from a conducting surface, with the photon frequency given approximately by the mass of the hidden photon. Here, we report on experimental efforts that have started recently to search for such hidden photon Dark Matter in the (sub-)eV regime with a prototype mirror for the Auger fluorescence detector at the Karlsruhe Institute for Technology.

  1. Optical dipole mirror for cold atoms based on a metallic diffraction grating

    DEFF Research Database (Denmark)

    Kawalec, Tomasz; Bartoszek-Bober, Dobroslawa; Panas, Roman

    We report on the realization of a plasmonic dipole mirror for cold atoms based on a metallic grating coupler. A cloud of atoms is reflected by the repulsive potential generated by surface plasmon polaritons (SPPs) excited on a reflection gold grating by a 780 nm laser beam. Experimentally...

  2. Optical dipole mirror for cold atoms based on a metallic diffraction grating

    DEFF Research Database (Denmark)

    Kawalec, Tomasz; Bartoszek-Bober, Dobroslawa; Panas, Roman

    2014-01-01

    We report on the realization of a plasmonic dipole mirror for cold atoms based on a metallic grating coupler. A cloud of atoms is reflected by the repulsive potential generated by surface plasmon polaritons (SPPs) excited on a reflection gold grating by a 780 nm laser beam. Experimentally...

  3. High index of refraction films for dielectric mirrors prepared by metal-organic chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Brusasco, R.M.

    1989-01-01

    A wide variety of metal oxides with high index of refraction can be prepared by Metal-Organic Chemical Vapor Deposition. We present some recent optical and laser damage results on oxide films prepared by MOCVD which could be used in a multilayer structure for highly reflecting (HR) dielectric mirror applications. The method of preparation affects both optical properties and laser damage threshold. 10 refs., 8 figs., 4 tabs.

  4. Goos-Hänchen shift for a rough metallic mirror.

    Science.gov (United States)

    Merano, M; Götte, J B; Aiello, A; van Exter, M P; Woerdman, J P

    2009-06-22

    We investigate experimentally the dependence of the Goos-Hänchen shift on the surface properties of an air-metal interface. The shift depends on the microscopic roughness of the metal surface but it is insensitive to the large-scale variations associated with surface non-flatness. Both an effective medium model of roughness and the Rayleigh-Rice theory of scattering are used to interpret the observed phenomenon.

  5. Derivation of the Lifshitz-Matsubara sum formula for the Casimir pressure between metallic plane mirrors

    Science.gov (United States)

    Guérout, R.; Lambrecht, A.; Milton, K. A.; Reynaud, S.

    2014-10-01

    We carefully reexamine the conditions of validity for the consistent derivation of the Lifshitz-Matsubara sum formula for the Casimir pressure between metallic plane mirrors. We recover the usual expression for the lossy Drude model but not for the lossless plasma model. We give an interpretation of this new result in terms of the modes associated with the Foucault currents, which play a role in the limit of vanishing losses, in contrast to common expectations.

  6. Lifshitz-Matsubara sum formula for the Casimir pressure between magnetic metallic mirrors

    Science.gov (United States)

    Guérout, R.; Lambrecht, A.; Milton, K. A.; Reynaud, S.

    2016-02-01

    We examine the conditions of validity for the Lifshitz-Matsubara sum formula for the Casimir pressure between magnetic metallic plane mirrors. As in the previously studied case of nonmagnetic materials [Guérout et al., Phys. Rev. E 90, 042125 (2014), 10.1103/PhysRevE.90.042125], we recover the usual expression for the lossy model of optical response, but not for the lossless plasma model. We also show that the modes associated with the Foucault currents play a crucial role in the limit of vanishing losses, in contrast to expectations.

  7. Generation and detection of thermoelastic waves in metals by a photothermal mirror method

    Science.gov (United States)

    Capeloto, O. A.; Zanuto, V. S.; Lukasievicz, G. V. B.; Malacarne, L. C.; Bialkowski, S. E.; Požar, T.; Astrath, N. G. C.

    2016-11-01

    We investigate the thermoelastic waves launched by a localized heat deposition. Pulsed laser excitation is used to generate mechanical perturbations in metals that are detected using the photothermal mirror method. This method detects the wavefront distortion of the probe beam reflected from the perturbed sample surface. Nanometer scale expansion of the material is induced just under the irradiated surface releasing transient thermoelastic waves of much smaller amplitudes on the surface. Numerical predictions and the experimental results are in a good agreement and represent both the thermal diffusion of the large amplitude, long-lasting outward bulge, and the released elastic waves.

  8. SUPERPOLISHED SI COATED SIC OPTICS FOR RAPID MANUFACTURE OF LARGE APERTURE UV AND EUV TELESCOPES Project

    Data.gov (United States)

    National Aeronautics and Space Administration — SSG/Tinsley proposes an innovative optical manufacturing process that will allow the advancement of state-of-the-art Silicon Carbide (SiC) mirrors for large aperture...

  9. Influence of Long-Term Plasma Irradiation on Metallic First Mirrors in HT-7 Tokamak

    Institute of Scientific and Technical Information of China (English)

    TANG Chunjiang; LI Renhong; CHEN Junling

    2008-01-01

    The first mirror (FM) samples made of polycrystal (PC) stainless steel (SS), molyb-denum (Mo) and tungsten (W) were mounted at different locations in HT-7 tokamak to investigate the surface modifications caused by erosion and deposition. The optical transmission character-istics of first mirror samples were measured by a spectrophotometer. It was found that different irradiation environment had different influences on the first mirror surfaces, especially with wave antenna nearby. In addition, the erosion made the refiectivity of FM degrade to some extents as a whole. But the deposition on the mirror influences more than erosion does. Comparing the mirrors of SS, W and Mo, irradiated in the same environment, the W-mirror had the least changes in reflectivity with regularity, while the SS-mirror had most serious changes.

  10. Experimental Simulation of the Behaviour of Diagnostic First Mirrors Fabricated of Different Metals for ITER Conditions

    OpenAIRE

    Voitsenya, V.; Bardamid, A. F.; Donne, A. J. H.

    2016-01-01

    In the experimental fusion reactor ITER, the plasma-facing component of each optical and/or laser diagnostic needs to be based on reflective optics with at least one mirror (first mirror) facing the thermonuclear plasma. The different kinds of radiation emanating from the burning plasma (neutrons, neutral atoms, electromagnetic radiation) create hostile operating conditions for the first mirrors. Therefore, a special program has been set up under the ITER framework aimed at solving the first ...

  11. Influence of Erosion and Deposition on Metallic First Mirror in HT-7 Tokamak

    Institute of Scientific and Technical Information of China (English)

    CHEN Ju; YAN Rong; CHEN Junling

    2012-01-01

    Abstract Dedicated experiments in the HT-7 tokamak were performed to investigate the in- fluence of erosion and deposition on the mirror samples. The first mirror (FM) samples made of polyerystalline (PC) stainless steel (SS), molybdenum (Mo) and tungsten (W) were fixed on a holder at an angle of 45° with respect to the horizontal plane and set at different locations with different connection lengths along the magnetic field. The optical reflectivity of the first mirror was measured by a spectrophotometer before and after plasma exposure. It was found that the surface morphology and specular reflectivity of the mirror samples after the exposure were different with respect to the different distances from the mirror surface to the last closed flux surface (LCFS) of the plasma in the tokamak. It was also found that shortening the connection length before the mirror surface would weaken the influence of the plasma erosion and impurity deposition on the mirror surface. In order to maintain the optical characteristics of the mirror surface, it is necessary to adopt the in-situ cleaning and mirror protection techniques.

  12. Long Focal Length Large Mirror Fabrication System

    Science.gov (United States)

    Bennett, H. E.

    2003-01-01

    The goals of this ambitious program are (1) to develop systems to make large superpolished optical mirrors, (2) to develop low scatter polishing techniques using centrifugal elutriation, (3) to develop a means of measuring scatter at any point on the mirror, (4) to polish a Hindle sphere to measure the optical figure of a one meter diameter convex mandrel, and (5) to fabricate low scatter, large adaptive optic graphite filled, cyanate ester replica transfer mirrors using these mandrels. Deliverables are a 30 cm diameter superpolished composite AO mirror. We fabricated a 1/3rd meter superpolished zerodur flat mandrel and with the support of our major subcontractor, Composite Mirror Applications Inc (CMA) we have demonstrated a 30 cm lightweight cyanate ester mirror with an rms microroughness between 0.6 and 0.8 nm and 8 faceplate influence function of 5 cm. The influence function was chosen to be comparable to the atmospheric correlation coefficient r(sub 0) which is about 5 cm at sea level. There was no print-thru of the graphite fibers in the cyanate ester surface (the bane of many previous efforts to use cyanate ester mirrors). Our subcontractor has devised a means for developing a 30-50 nm thick layer of graphite free pure ester resin on the surface of the mirrors. This graphite fiber filled material has a thermal expansion coefficient in the 10(exp -8) centimeter per Kelvin range (the same range of expansion coefficient as Zerodur and ULE glasses) and does not take up water and swell, so it is a nearly ideal mirror material in these areas. Unfortunately for these 0.8mm thick faceplates, the number of plies is not enough to result in isometric coverage. Isolated figure irregularities can appear, making it necessary to go to thicker faceplates. The influence function will then only approximate the length of r(sub 0), at higher altitudes or longer wavelengths. The influence function goes as the cube of the thickness, so we are now making a faceplate optimized for

  13. Optical dipole mirror for cold atoms based on a metallic diffraction grating

    DEFF Research Database (Denmark)

    Kawalec, Tomasz; Bartoszek-Bober, Dobroslawa; Panas, Roman

    2014-01-01

    and numerically determined mirror efficiencies are close to 100%. The intensity of SPPs above a real grating coupler and the atomic trajectories, as well as the momentum dispersion of the atom cloud being reflected, are computed. A suggestion is given as to how the plasmonic mirror might serve as an optical atom...

  14. Experimental Simulation of the Behaviour of Diagnostic First Mirrors Fabricated of Different Metals for ITER Conditions

    NARCIS (Netherlands)

    Voitsenya, V.; Bardamid, A. F.; Donne, A. J. H.

    2016-01-01

    In the experimental fusion reactor ITER, the plasma-facing component of each optical and/or laser diagnostic needs to be based on reflective optics with at least one mirror (first mirror) facing the thermonuclear plasma. The different kinds of radiation emanating from the burning plasma (neutrons, n

  15. Sub-nanometer flattening of a 45-cm long, 45-actuator x-ray deformable mirror

    CERN Document Server

    Poyneer, L A; Pardini, T; Palmer, D; Brooks, A; Pivovaroff, M J; Macintosh, B

    2014-01-01

    We have built a 45-cm long x-ray deformable mirror of super-polished single-crystal silicon that has 45 actuators along the tangential axis. After assembly the surface height error was 19 nm rms. With use of high-precision visible-light metrology and precise control algorithms, we have actuated the x-ray deformable mirror and flattened its entire surface to 0.7 nm rms controllable figure error. This is, to our knowledge, the first sub-nanometer active flattening of a substrate longer than 15 cm.

  16. First studies of ITER-diagnostic mirrors in a tokamak with an all-metal interior: results of the first mirror test in ASDEX Upgrade

    NARCIS (Netherlands)

    Litnovsky, A.; Matveeva, M.; Herrmann, A.; Rohde, V.; Mayer, M.; Sugiyama, K.; Krieger, K.; Voitsenya, V.; Vayakis, G.; Costley, A. E.; Reichle, R.; De Temmerman, G.; Richter, S.; Breuer, U.; Buzi, L.; Möller, S.; Philipps, V.; Samm, U.; Wienhold, P.

    2013-01-01

    In ITER, mirrors will be used as plasma-viewing elements in all optical and laser diagnostics. In the harsh environment, mirror performance will degrade hampering the operation of associated diagnostics. The most adverse effect on mirror performance is caused by the deposition of impurities. It is e

  17. A theoretical investigation of the laser damage threshold of metal multi-dielectric mirrors for high power ultrashort applications.

    Science.gov (United States)

    Wang, Bin; Gallais, Laurent

    2013-06-17

    An approach for the theoretical evaluation of the damage threshold in optical interference coatings that combine metal and dielectric films is presented. The model that is used combines a matrix formalism to describe the film system with the two temperatures model that describes the energy transfer and the temperatures of electrons and lattice in a solid submitted to a laser irradiation at the femtosecond time scale. With this approach the thermal consequences due to the ultrafast absorption of the metal film can be evaluated in the multilayer stack for single or multiple pulses. Some applications are presented for the case of broadband mirrors for ultrashort pulses with low dispersion. Particularly we study the impact of the metal film (metal element, thickness) and the design on the Laser Induced Damage Threshold in the sub picosecond regime.

  18. Profile etching for prefiguring X-ray mirrors.

    Science.gov (United States)

    Liu, Chian; Qian, Jun; Assoufid, Lahsen

    2015-03-01

    A method to pre-shape mirror substrates through etching with a broad-beam ion source and a contoured mask is presented. A 100 mm-long elliptical cylinder substrate was obtained from a super-polished flat Si substrate with a 48 nm root-mean-square (r.m.s.) figure error and a 1.5 Å r.m.s. roughness after one profile-etching process at a beam voltage of 600 V without iteration. A follow-up profile coating can be used to achieve a final mirror. Profile etching and profile coating combined provide an economic way to make X-ray optics, such as nested Kirkpatrick-Baez mirrors.

  19. Liquid metal actuators: correctable mounting and assembly of thin-shell x-ray telescope mirrors

    Science.gov (United States)

    Bruccoleri, Alexander R.; Klingensmith, Martin; Chalifoux, Brandon; Heilmann, Ralf K.; Schattenburg, Mark L.

    2015-09-01

    An ideal bonding agent for thin-shell x-ray mirrors could be quickly applied to joints and set with deterministic and stable properties. Unfortunately, mirror assembly methods have typically utilized various epoxy formulations which are messy, slow to apply and cure, and far from deterministic or stable. Problems include shrinkage, creep and high thermal and humidity sensitivity. Once the bond is set errors are frozen in and cannot be corrected. We are developing a new method for bonding thin-foil mirrors that has the potential to solve these problems. Our process to bond mirrors to housing reference points is achieved via small beads of a low-melting-point bonding agent (such as solder or thermoset). The mirror is bonded to small contact surface points under real-time metrology. If the position of the mirror needs to be adjusted after bonding, a small force is applied normal or parallel to the contact surface and a pulsed fiber laser is used to melt an ultrathin layer of the solder for a very short time. The joint is then compressed, stretched or sheared while molten before refreezing in a new position, enabling repeatable and stable mirror position adjustments along the direction of the force in nm-level steps with minimal heat input. We present results from our prototype apparatus demonstrating proof of principle. The initial experiment includes developing a technique to bond D263 glass to Kovar, designing and building a one-dimensional stage to precisely apply force, and using an infrared laser pulse to heat the joint while measuring position and force.

  20. Visible quality aluminum and nickel superpolish polishing technology enabling new missions

    Science.gov (United States)

    Carrigan, Keith G.

    2011-06-01

    It is now well understood that with US Department of Defense (DoD) budgets shrinking and the Services and Agencies demanding new systems which can be fielded more quickly, cost and schedule are being emphasized more and more. At the same time, the US has ever growing needs for advanced capabilities to support evolving Intelligence, Surveillance and Reconnaissance objectives. In response to this market demand for ever more cost-effective, faster to market, single-channel, athermal optical systems, we have developed new metal polishing technologies which allow for short-lead, low-cost metal substrates to replace more costly, longer-lead material options. In parallel, the commercial marketplace is being driven continually to release better, faster and cheaper electronics. Growth according to Moore's law, enabled by advancements in photolithography, has produced denser memory, higher resolution displays and faster processors. While the quality of these products continues to increase, their price is falling. This seeming paradox is driven by industry advancements in manufacturing technology. The next steps on this curve can be realized via polishing technology which allows low-cost metal substrates to replace costly Silicon based optics for use in ultra-short wavelength systems.

  1. Miniaturization of an optical 3D sensor by additive manufacture of metallic mirrors

    Science.gov (United States)

    Sigel, Andre; Merkel, Markus; Heinrich, Andreas

    2017-06-01

    Based on progress in the field of additive manufacturing optical components can now be printed with rapid prototyping technologies. In this contribution the possibilities of rapid prototyping for optical metrology are exemplified by the fabrication of miniaturized reflectors and the construction of a miniaturized metrology system designed for an industrial metrology application. Focusing on the manufacturing and post processing steps the process chain to fabricate the miniaturized mirror is described. This includes an evaluation of the mirror based on roughness measurements. The reflectors are later utilized in a miniaturized sensor system to scan the interior of small pipes. The additively manufactured mirror is used in the metrology system to create a defined sampling signal within the cavity. Thereby the sensor system generates a point cloud of the internal surfaces using a 3D acquisition algorithm based on the laser triangulation principle. Part of this contribution will be the setup, the 3D acquisition and calibration principle as well as an evaluation of the metrology system. To optimize the point cloud acquisition three different hardware setups were designed using different cameras and calibration algorithms. These three approaches are evaluated and compared.

  2. Sub-nanometer flattening of 45 cm long, 45 actuator x-ray deformable mirror.

    Science.gov (United States)

    Poyneer, Lisa A; McCarville, Thomas; Pardini, Tommaso; Palmer, David; Brooks, Audrey; Pivovaroff, Michael J; Macintosh, Bruce

    2014-06-01

    We have built a 45 cm long x-ray deformable mirror (XDM) of super-polished single-crystal silicon that has 45 actuators along the tangential axis. After assembly, the surface height error was 19 nm rms. With use of high-precision visible-light metrology and precise control algorithms, we have actuated the XDM and flattened its entire surface to 0.7 nm rms controllable figure error. This is, to our knowledge, the first sub-nanometer active flattening of a substrate longer than 15 cm.

  3. Plasmonic gap-mode nanocavities with metallic mirrors in high-index cladding.

    Science.gov (United States)

    Cheng, Pi-Ju; Weng, Chen-Ya; Chang, Shu-Wei; Lin, Tzy-Rong; Tien, Chung-Hao

    2013-06-03

    We theoretically analyze plasmonic gap-mode nanocavities covered by a thick cladding layer at telecommunication wavelengths. In the presence of high-index cladding materials such as semiconductors, the first-order hybrid gap mode becomes more promising for lasing than the fundamental one. Still, the significant mirror loss remains the main challenge to lasing. Using silver coatings within a decent thickness range at two end facets, we show that the reflectivity is substantially enhanced above 95 %. At a coating thickness of 50 nm and cavity length of 1.51 μm, the quality factor is about 150, and the threshold gain is lower than 1500 cm(-1).

  4. Evanescent Wave Atomic Mirror

    Science.gov (United States)

    Ghezali, S.; Taleb, A.

    2008-09-01

    A research project at the "Laboratoire d'électronique quantique" consists in a theoretical study of the reflection and diffraction phenomena via an atomic mirror. This poster presents the principle of an atomic mirror. Many groups in the world have constructed this type of atom optics experiments such as in Paris-Orsay-Villetaneuse (France), Stanford-Gaithersburg (USA), Munich-Heidelberg (Germany), etc. A laser beam goes into a prism with an incidence bigger than the critical incidence. It undergoes a total reflection on the plane face of the prism and then exits. The transmitted resulting wave out of the prism is evanescent and repulsive as the frequency detuning of the laser beam compared to the atomic transition δ = ωL-ω0 is positive. The cold atomic sample interacts with this evanescent wave and undergoes one or more elastic bounces by passing into backward points in its trajectory because the atoms' kinetic energy (of the order of the μeV) is less than the maximum of the dipolar potential barrier ℏΩ2/Δ where Ω is the Rabi frequency [1]. In fact, the atoms are cooled and captured in a magneto-optical trap placed at a distance of the order of the cm above the prism surface. The dipolar potential with which interact the slow atoms is obtained for a two level atom in a case of a dipolar electric transition (D2 Rubidium transition at a wavelength of 780nm delivered by a Titane-Saphir laser between a fundamental state Jf = l/2 and an excited state Je = 3/2). This potential is corrected by an attractive Van der Waals term which varies as 1/z3 in the Lennard-Jones approximation (typical atomic distance of the order of λ0/2π where λ0 is the laser wavelength) and in 1/z4 if the distance between the atom and its image in the dielectric is big in front of λ0/2π. This last case is obtained in a quantum electrodynamic calculation by taking into account an orthornormal base [2]. We'll examine the role of spontaneous emission for which the rate is inversely

  5. A Novel Method for Fabricating Additive Manufactured Lightweight, Optical Quality Metallic Mirrors

    Science.gov (United States)

    2016-01-04

    since there were challenges to  overcome the non‐standard  alloys  and levels of porosity bulk metallic properties of the printed  material. The second...material to achieve flatness on the order of one micron and  surface roughness on the order of one nanometer [11]. Materials with high  ferrous  content...This limits the use of many prevalent metal additive materials, including high silicon  content aluminum, titanium  alloys , and  alloys  with high

  6. A Passively Mode-Locked Diode-End-Pumped Nd:YAG Laser with a Semiconductor Saturable Absorber Mirror Grown by Metal Organic Chemical Vapour Deposition

    Institute of Scientific and Technical Information of China (English)

    王勇刚; 马骁宇; 李春勇; 张治国; 张丙元; 张志刚

    2003-01-01

    We report the experimental results of a mode-locked diode-end-pumped Nd:YAG laser with a semiconductor saturable absorber mirror(SESAM)from which we achieved a 10ps pulse duration at 150MHz repetition rate.The SESAM was grown by metal organic chemical vapour deposition at low temperature.The recovery time was measured to be 0.5 ps,indicating the potential pulse compression to sub-picoseconds.

  7. Bimorph mirrors: The Good, the Bad, and the Ugly

    Energy Technology Data Exchange (ETDEWEB)

    Alcock, Simon G., E-mail: simon.alcock@diamond.ac.uk [Diamond Light Source Ltd., Harwell Science and Innovation Campus, Oxfordshire OX11 0DE (United Kingdom); Sutter, John P.; Sawhney, Kawal J.S.; Hall, David R.; McAuley, Katherine; Sorensen, Thomas [Diamond Light Source Ltd., Harwell Science and Innovation Campus, Oxfordshire OX11 0DE (United Kingdom)

    2013-05-11

    Bimorph mirrors are widely used by the X-ray, Laser, Space, and Astronomy communities to focus or collimate photon beams. Applying voltages to the embedded piezo ceramics enables the user to globally bend the optical substrate to a range of figures (including cylindrical, parabolic, and elliptical), and finely correct low spatial frequency errors, thus improving optical performance. Bimorph mirrors are employed on numerous synchrotron X-ray beamlines, including several at Diamond Light Source. However, many such beamlines were not achieving the desired size and shape of the reflected X-ray beam. Metrology data from ex-situ, slope measuring profilometry (using the Diamond-NOM) and in-situ, synchrotron X-ray “pencil-beam” scans, revealed sharp defects on the optical substrate directly above the locations at which the piezo ceramics are bonded together. This so-called “junction effect” has been observed on a variety of bimorph mirrors with different numbers of piezos, substrate length, and thickness. To repair this damage, three pairs of bimorph mirrors were re-polished at Thales-SESO. We review the re-polishing process, and show that it successfully removed the junction effect, and significantly improved beamline performance. Since the internal structure of the bimorph mirrors was not modified during re-polishing, it is hoped that the mirrors will retain their surface quality, and remain operational for many years. We also highlight the combination of super-polishing techniques with bimorph technology to create the “Ultimate” mirror, and discuss a next generation, bimorph mirror which is predicted not to suffer from the junction effect.

  8. Bimorph mirrors: The Good, the Bad, and the Ugly

    Science.gov (United States)

    Alcock, Simon G.; Sutter, John P.; Sawhney, Kawal J. S.; Hall, David R.; McAuley, Katherine; Sorensen, Thomas

    2013-05-01

    Bimorph mirrors are widely used by the X-ray, Laser, Space, and Astronomy communities to focus or collimate photon beams. Applying voltages to the embedded piezo ceramics enables the user to globally bend the optical substrate to a range of figures (including cylindrical, parabolic, and elliptical), and finely correct low spatial frequency errors, thus improving optical performance. Bimorph mirrors are employed on numerous synchrotron X-ray beamlines, including several at Diamond Light Source. However, many such beamlines were not achieving the desired size and shape of the reflected X-ray beam. Metrology data from ex-situ, slope measuring profilometry (using the Diamond-NOM) and in-situ, synchrotron X-ray "pencil-beam" scans, revealed sharp defects on the optical substrate directly above the locations at which the piezo ceramics are bonded together. This so-called "junction effect" has been observed on a variety of bimorph mirrors with different numbers of piezos, substrate length, and thickness. To repair this damage, three pairs of bimorph mirrors were re-polished at Thales-SESO. We review the re-polishing process, and show that it successfully removed the junction effect, and significantly improved beamline performance. Since the internal structure of the bimorph mirrors was not modified during re-polishing, it is hoped that the mirrors will retain their surface quality, and remain operational for many years. We also highlight the combination of super-polishing techniques with bimorph technology to create the "Ultimate" mirror, and discuss a next generation, bimorph mirror which is predicted not to suffer from the junction effect.

  9. Ultra-lightweight, Low Scatter, Large Mirror Technology

    Science.gov (United States)

    Bennett, H. E.

    2006-01-01

    A technique is being developed to fabricate a prototype lightweight composite mirror one meter in diameter. The mandrel, on which the composite mirror will be laid up, is an ultra low expansion quartz glass, TSG, whose thermal expansion coefficient, 10(exp -7)/ degC or less, is similar to that for the composite material itself. The mandrel surface will be super-polished to 6-8 A rms or better, resulting in ten times less scattered light in the visible region than is found in typical astronomical mirrors. We have shown experimentally that mandrel micro-roughnesses of this order can be successfully replicated on composite faceplates. The faceplate is very tough, and does not fracture like a thin glass faceplate. It will be supported by actuators alone, not by the edge of the mirror mount, to avoid non-uniform or non-symmetric influence functions. BOR developed actuators are designed for atmospheric correction, maintenance of optical figure, and minor tip tilt. They have a throw of a centimeter, can be controlled remotely, and have a response time of 1/2 msec. The piezoelectric part of the actuator operates in the 30-70 V range and the differential screw portion has a linearity of about +/-0.1 microns.

  10. Highly efficient vertical fiber interfacing grating coupler with bilayer anti-reflection cladding and backside metal mirror

    Science.gov (United States)

    Zhang, Zanyun; Huang, Beiju; Zhang, Zan; Cheng, Chuantong; Liu, Hongwei; Li, Hongqiang; Chen, Hongda

    2017-05-01

    A highly efficient bidirectional grating coupler for perfectly vertical coupling is designed. With a Si3N4/SiO2 bilayer structure and a backside metal mirror acting as anti-reflection cladding (ARC) and substrate reflector respectively, the coupling efficiency can be greatly enhanced for a cost-effective uniform grating coupler. To maximize the grating coupling, all the grating parameters including the bilayer thicknesses are fully optimized using numerical simulation method. As a design trade-off between coupling efficiency (CE) and optical bandwidth (OB), CE of 88.3% (-0.54 dB) and 1-dB bandwidth of 61 nm can be obtained. In addition, this grating coupler shows strong fiber misalignment tolerance. With a 2 μm fiber misalignment, the coupling loss increases by less than 0.5 dB and the up-reflection loss increases by less than 2 dB. Also it is found that the splitting behavior of the grating is quite stable near the grating resonant wavelength. Such characteristics make this device very attractive for low-cost photonic packaging and Mach-Zehnder type device applications. In addition, two optimal designs are presented based on the Particle Swarm Optimization (PSO) method and genetic algorithm (GA). Numerical calculated results show that the coupling efficiency at center wavelength can be further improved compared to that of the balanced design. However, the optical bandwidth suffer at a expense. At last, Fourier analysis of the grating is carried out to analyze the optical field profile and frequency spectrum of the grating region. It is believed such a grating structure can provide flexible designs for different coupler requirements and applications.

  11. Einstein's Mirror

    Science.gov (United States)

    Gjurchinovski, Aleksandar; Skeparovski, Aleksandar

    2008-01-01

    Reflection of light from a plane mirror in uniform rectilinear motion is a century-old problem, intimately related to the foundations of special relativity. The problem was first investigated by Einstein in his famous 1905 paper by using the Lorentz transformations to switch from the mirror's rest frame to the frame where the mirror moves at a…

  12. Chiral mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Plum, Eric, E-mail: erp@orc.soton.ac.uk [Optoelectronics Research Centre and Centre for Photonic Metamaterials, University of Southampton, Highfield, Southampton SO17 1BJ (United Kingdom); Zheludev, Nikolay I., E-mail: niz@orc.soton.ac.uk [Optoelectronics Research Centre and Centre for Photonic Metamaterials, University of Southampton, Highfield, Southampton SO17 1BJ (United Kingdom); The Photonics Institute and Centre for Disruptive Photonic Technologies, Nanyang Technological University, Singapore 637378 (Singapore)

    2015-06-01

    Mirrors are used in telescopes, microscopes, photo cameras, lasers, satellite dishes, and everywhere else, where redirection of electromagnetic radiation is required making them arguably the most important optical component. While conventional isotropic mirrors will reflect linear polarizations without change, the handedness of circularly polarized waves is reversed upon reflection. Here, we demonstrate a type of mirror reflecting one circular polarization without changing its handedness, while absorbing the other. The polarization-preserving mirror consists of a planar metasurface with a subwavelength pattern that cannot be superimposed with its mirror image without being lifted out of its plane, and a conventional mirror spaced by a fraction of the wavelength from the metasurface. Such mirrors enable circularly polarized lasers and Fabry-Pérot cavities with enhanced tunability, gyroscopic applications, polarization-sensitive detectors of electromagnetic waves, and can be used to enhance spectroscopies of chiral media.

  13. Numerical investigation of multi-beam laser heterodyne measurement with ultra-precision for linear expansion coefficient of metal based on oscillating mirror modulation

    Institute of Scientific and Technical Information of China (English)

    Li Yan-Chao; Wang Chun-Hui; Qu Yang; Gao Long; Cong Hai-Fang; Yang Yan-Ling; Gao Jie; Wang Ao-You

    2011-01-01

    This paper proposes a novel method of multi-beam laser heterodyne measurement for metal linear expansion coefficient. Based on the Doppler effect and heterodyne technology, the information is loaded of length variation to the frequency difference of the multi-beam laser heterodyne signal by the frequency modulation of the oscillating mirror,this method can obtain many values of length variation caused by temperature variation after the multi-beam laser heterodyne signal demodulation simultaneously. Processing these values by weighted-average, it can obtain length variation accurately, and eventually obtain the value of linear expansion coefficient of metal by the calculation. This novel method is used to simulate measurement for linear expansion coefficient of metal rod under different temperatures by MATLAB, the obtained result shows that the relative measurement error of this method is just 0.4%.

  14. Magic Mirrors

    Science.gov (United States)

    Mills, Allan

    2011-01-01

    "Magic mirrors" were so named because, when they were positioned to throw a reflected patch of sunlight on a nearby wall, this area contained an outline of a design cast on the back of the (bronze) mirror. Investigations begun in the 19th century showed that this was a response to heavy localized pressures exerted on the face of the thin mirror…

  15. Mirror symmetry

    CERN Document Server

    Voisin, Claire

    1999-01-01

    This is the English translation of Professor Voisin's book reflecting the discovery of the mirror symmetry phenomenon. The first chapter is devoted to the geometry of Calabi-Yau manifolds, and the second describes, as motivation, the ideas from quantum field theory that led to the discovery of mirror symmetry. The other chapters deal with more specialized aspects of the subject: the work of Candelas, de la Ossa, Greene, and Parkes, based on the fact that under the mirror symmetry hypothesis, the variation of Hodge structure of a Calabi-Yau threefold determines the Gromov-Witten invariants of its mirror; Batyrev's construction, which exhibits the mirror symmetry phenomenon between hypersurfaces of toric Fano varieties, after a combinatorial classification of the latter; the mathematical construction of the Gromov-Witten potential, and the proof of its crucial property (that it satisfies the WDVV equation), which makes it possible to construct a flat connection underlying a variation of Hodge structure in the ...

  16. Mirror neurons

    National Research Council Canada - National Science Library

    Rubia Vila, Francisco José

    2011-01-01

    Mirror neurons were recently discovered in frontal brain areas of the monkey. They are activated when the animal makes a specific movement, but also when the animal observes the same movement in another animal...

  17. Design and Fabrication of a Large-Stroke Deformable Mirror Using a Gear-Shape Ionic-Conductive Polymer Metal Composite

    Directory of Open Access Journals (Sweden)

    Guo-Dung John Su

    2012-08-01

    Full Text Available Conventional camera modules with image sensors manipulate the focus or zoom by moving lenses. Although motors, such as voice-coil motors, can move the lens sets precisely, large volume, high power consumption, and long moving time are critical issues for motor-type camera modules. A deformable mirror (DM provides a good opportunity to improve these issues. The DM is a reflective type optical component which can alter the optical power to focus the lights on the two dimensional optical image sensors. It can make the camera system operate rapidly. Ionic polymer metal composite (IPMC is a promising electro-actuated polymer material that can be used in micromachining devices because of its large deformation with low actuation voltage. We developed a convenient simulation model based on Young’s modulus and Poisson’s ratio. We divided an ion exchange polymer, also known as Nafion®, into two virtual layers in the simulation model: one was expansive and the other was contractive, caused by opposite constant surface forces on each surface of the elements. Therefore, the deformation for different IPMC shapes can be described more easily. A standard experiment of voltage vs. tip displacement was used to verify the proposed modeling. Finally, a gear shaped IPMC actuator was designed and tested. Optical power of the IPMC deformable mirror is experimentally demonstrated to be 17 diopters with two volts. The needed voltage was about two orders lower than conventional silicon deformable mirrors and about one order lower than the liquid lens.

  18. White Light Focusing Mirror

    Science.gov (United States)

    Johnson, Eric; Lyndaker, Aaron; Deyhim, Alex; Sullivan, Michael; Chance, Mark; Abel, Don; Toomey, John; Hulbert, Steven

    2007-01-01

    The NSLS X28C white-light beamline is being outfitted with a focusing mirror in order to increase, as well as control, the x-ray intensity at the sample position. The new mirror is a 50 mm × 100 mm × 1100 mm single crystal silicon cylindrical 43.1mm radius substrate bendable to a toroid from infinite to 1200 m radius. The unique feature of this mirror system is the dual use of Indalloy 51 as both a mechanism for heat transfer and a buoyant support to negate the effects of gravity. The benefit of the liquid metal support is the ability to correct for minor slope errors that take the form of a parabola. A bobber mechanism is employed to displace the fluid under the mirror +/- 1.5 mm. This allows RMS slope error correction on the order of 2 urad. The unique mounting of the mirror ensures the contributions to slope error from errant mechanical stresses due to machining tolerances are virtually non-existent. After correction, the surface figure error (measured minus ideal) is <= 0.5 urad rms.

  19. Mirror, mirror on the wall

    CERN Multimedia

    2005-01-01

    RICH 2, one of the two Ring Imaging Cherenkov detectors of the LHCb experiment, is being prepared to join the other detector elements ready for the first proton-proton collisions at LHC. The mirrors of the RICH2 detector are meticulously assembled in a clean room.In a large dark room, men in white move around an immense structure some 7 metres high, 10 metres wide and nearly 2.5 metres deep. Apparently effortlessly, they are installing the two large high-precision spherical mirrors. These mirrors will focus Cherenkov light, created by the charged particles that will traverse this detector, onto the photon detectors. Each spherical mirror wall is made up of facets like a fly's eye. Twenty-eight individual thin glass mirrors will all point to the same point in space to within a few micro-radians. The development of these mirrors has been technically demanding : Ideally they should be massless, sturdy, precise and have high reflectivity. In practice, though not massless, they are made from a mere 6 mm thin gl...

  20. [Mirror neurons].

    Science.gov (United States)

    Rubia Vila, Francisco José

    2011-01-01

    Mirror neurons were recently discovered in frontal brain areas of the monkey. They are activated when the animal makes a specific movement, but also when the animal observes the same movement in another animal. Some of them also respond to the emotional expression of other animals of the same species. These mirror neurons have also been found in humans. They respond to or "reflect" actions of other individuals in the brain and are thought to represent the basis for imitation and empathy and hence the neurobiological substrate for "theory of mind", the potential origin of language and the so-called moral instinct.

  1. What do mirror neurons mirror?

    NARCIS (Netherlands)

    Uithol, S.; Rooij, I.J.E.I. van; Bekkering, H.; Haselager, W.F.G.

    2011-01-01

    Single cell recordings in monkeys provide strong evidence for an important role of the motor system in action understanding. This evidence is backed up by data from studies of the (human) mirror neuron system using neuroimaging or TMS techniques, and behavioral experiments. Although the data acquire

  2. What do mirror neurons mirror?

    NARCIS (Netherlands)

    Uithol, S.; Rooij, I.J.E.I. van; Bekkering, H.; Haselager, W.F.G.

    2011-01-01

    Single cell recordings in monkeys provide strong evidence for an important role of the motor system in action understanding. This evidence is backed up by data from studies of the (human) mirror neuron system using neuroimaging or TMS techniques, and behavioral experiments. Although the data

  3. Mirror monochromator

    Energy Technology Data Exchange (ETDEWEB)

    Mankos, Marian [Electron Optica, Inc., Palo Alto, CA (United States); Shadman, Khashayar [Electron Optica, Inc., Palo Alto, CA (United States)

    2014-12-02

    In this SBIR project, Electron Optica, Inc. (EOI) is developing a mirror electron monochromator (MirrorChrom) attachment to new and retrofitted electron microscopes (EMs) for improving the energy resolution of the EM from the characteristic range of 0.2-0.5 eV to the range of 10-50 meV. This improvement will enhance the characterization of materials by imaging and spectroscopy. In particular, the monochromator will refine the energy spectra characterizing materials, as obtained from transmission EMs [TEMs] fitted with electron spectrometers, and it will increase the spatial resolution of the images of materials taken with scanning EMs (SEMs) operated at low voltages. EOI’s MirrorChrom technology utilizes a magnetic prism to simultaneously deflect the electron beam off the axis of the microscope column by 90° and disperse the electrons in proportional to their energies into a module with an electron mirror and a knife-edge. The knife-edge cuts off the tails of the energy distribution to reduce the energy spread of the electrons that are reflected, and subsequently deflected, back into the microscope column. The knife-edge is less prone to contamination, and thereby charging, than the conventional slits used in existing monochromators, which improves the reliability and stability of the module. The overall design of the MirrorChrom exploits the symmetry inherent in reversing the electron trajectory in order to maintain the beam brightness – a parameter that impacts how well the electron beam can be focused downstream onto a sample. During phase I, EOI drafted a set of candidate monochromator architectures and evaluated the trade-offs between energy resolution and beam current to achieve the optimum design for three particular applications with market potential: increasing the spatial resolution of low voltage SEMs, increasing the energy resolution of low voltage TEMs (beam energy of 5-20 keV), and increasing the energy resolution of conventional TEMs (beam

  4. Mirror systems

    Energy Technology Data Exchange (ETDEWEB)

    Howells, M.R.

    1985-12-01

    The physics of VUV and x-ray reflection is reviewed. The main functions of mirrors in synchrotron beamlines are stated briefly and include deflection, filtration, power absorption, formation of a real image of the source, focusing, and collimation. Methods of fabrication of optical surfaces are described. Types of imperfections are discussed, including, aberrations, surface figure inaccuracy, roughness, and degradation due to use. Calculation of the photon beam thermal load, including computer modelling, is considered. 50 refs., 7 figs. (LEW)

  5. Metamaterial mirrors in optoelectronic devices

    KAUST Repository

    Esfandyarpour, Majid

    2014-06-22

    The phase reversal that occurs when light is reflected from a metallic mirror produces a standing wave with reduced intensity near the reflective surface. This effect is highly undesirable in optoelectronic devices that use metal films as both electrical contacts and optical mirrors, because it dictates a minimum spacing between the metal and the underlying active semiconductor layers, therefore posing a fundamental limit to the overall thickness of the device. Here, we show that this challenge can be circumvented by using a metamaterial mirror whose reflection phase is tunable from that of a perfect electric mirror († = €) to that of a perfect magnetic mirror († = 0). This tunability in reflection phase can also be exploited to optimize the standing wave profile in planar devices to maximize light-matter interaction. Specifically, we show that light absorption and photocurrent generation in a sub-100 nm active semiconductor layer of a model solar cell can be enhanced by ∼20% over a broad spectral band. © 2014 Macmillan Publishers Limited.

  6. Polymer glazing for silver mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Neidlinger, H H; Schissel, P

    1985-07-01

    This paper reports on an evaluation and modification of polymeric glazings to protect silver mirrors. The mirrors were made using Corning 7809 glass as a substrate onto which a thin silver film is deposited. The modified polymeric films are then cast from solution onto the silver. The mirrors were characterized by measuring the hemispherical reflectance and the specular reflectance at 660 nm and selected acceptance angles (7.5 mrad or 3.5 mrad). The mirrors were exposed to environmental degradation using accelerated weathering devices and outdoor exposure. Empirical evidence has demonstrated that polymethylmethacrylate is a stable polymer in a terrestrial environment, but the polymer does not provide adequate protection for the silver reflector. The crucial role in degradation played by ultraviolet (uv) light is shown by several experimental results. It has been demonstrated that uv stabilizers added to the polymer improve the weatherability of mirrors. The relative effectiveness of different stabilizers will be discussed in terms of the weathering modes, retention of optical properties, and effectiveness of the additives. The process for silver deposition influences the reflectance of silver mirrors, and the optical properties depend on subtle relationships between the metallization and the dielectric (polymeric) films that are in contact with the silver.

  7. High reflection mirrors for pulse compression gratings.

    Science.gov (United States)

    Palmier, S; Neauport, J; Baclet, N; Lavastre, E; Dupuy, G

    2009-10-26

    We report an experimental investigation of high reflection mirrors used to fabricate gratings for pulse compression application at the wavelength of 1.053microm. Two kinds of mirrors are studied: the mixed Metal MultiLayer Dielectric (MMLD) mirrors which combine a gold metal layer with some e-beam evaporated dielectric bilayers on the top and the standard e-beam evaporated MultiLayer Dielectric (MLD) mirrors. Various samples were manufactured, damage tested at a pulse duration of 500fs. Damage sites were subsequently observed by means of Nomarski microscopy and white light interferometer microscopy. The comparison of the results evidences that if MMLD design can offer damage performances rather similar to MLD design, it also exhibits lower stresses; being thus an optimal mirror substrate for a pulse compression grating operating under vacuum.

  8. Mirror-image-induced magnetic modes.

    Science.gov (United States)

    Xifré-Pérez, Elisabet; Shi, Lei; Tuzer, Umut; Fenollosa, Roberto; Ramiro-Manzano, Fernando; Quidant, Romain; Meseguer, Francisco

    2013-01-22

    Reflection in a mirror changes the handedness of the real world, and right-handed objects turn left-handed and vice versa (M. Gardner, The Ambidextrous Universe, Penguin Books, 1964). Also, we learn from electromagnetism textbooks that a flat metallic mirror transforms an electric charge into a virtual opposite charge. Consequently, the mirror image of a magnet is another parallel virtual magnet as the mirror image changes both the charge sign and the curl handedness. Here we report the dramatic modification in the optical response of a silicon nanocavity induced by the interaction with its image through a flat metallic mirror. The system of real and virtual dipoles can be interpreted as an effective magnetic dipole responsible for a strong enhancement of the cavity scattering cross section.

  9. Double arch mirror study

    Science.gov (United States)

    Vukobratovich, D.; Hillman, D.

    1983-01-01

    The development of a method of mounting light weight glass mirrors for astronomical telescopes compatible with the goals of the Shuttle Infrared Telescope Facility (SIRTF) was investigated. A 20 in. diameter double arch lightweight mirror previously fabricated was modified to use a new mount configuration. This mount concept was developed and fabricated. The mounting concept of the double mounting mirror is outlined. The modifications made to the mirror, fabrication of the mirror mount, and room temperature testing of the mirror and mount and the extension of the mirror and mount concept to a full size (40 in. diameter) primary mirror for SIRTF are discussed.

  10. Characterization of a flat superpolished mandrel prototype with hard (TiN / SiC) overcoating to enhance the surface durability

    CERN Document Server

    Spiga, D

    2015-01-01

    A number of hard X-Ray (10 - 100 KeV) astronomical missions of near future will make use of multilayer-coated focusing mirrors. The technology based on Nickel electroformed replication is suitable for the multilayer optics realization, since multi-modular telescopes are foreseen. For example, for the Constellation-X mission there is the need of realizing up to 14 identical modules (12 flight modules plus two spares) which can be replicated by the same series of mandrels. The Ni replication approach is derived from the method already successfully used for making the Au coated soft X-ray mirrors with good imaging performances of the missions BeppoSAX, XMM-Newton and Swift. In the technological extension of the process to the multilayer optics fabrication, it would be convenient to overcoat the external surface of mandrels (normally in Kanigen) with a layer made of a very hard material. This would help to maintain the very low roughness level requested by the application (typically less than a couple of Angstrom...

  11. Mirror Neurons and Mirror-Touch Synesthesia.

    Science.gov (United States)

    Linkovski, Omer; Katzin, Naama; Salti, Moti

    2016-05-30

    Since mirror neurons were introduced to the neuroscientific community more than 20 years ago, they have become an elegant and intuitive account for different cognitive mechanisms (e.g., empathy, goal understanding) and conditions (e.g., autism spectrum disorders). Recently, mirror neurons were suggested to be the mechanism underlying a specific type of synesthesia. Mirror-touch synesthesia is a phenomenon in which individuals experience somatosensory sensations when seeing someone else being touched. Appealing as it is, careful delineation is required when applying this mechanism. Using the mirror-touch synesthesia case, we put forward theoretical and methodological issues that should be addressed before relying on the mirror-neurons account. © The Author(s) 2016.

  12. Durable solar mirror films

    Energy Technology Data Exchange (ETDEWEB)

    O' Neill, Mark B.; Henderson, Andrew J.; Hebrink, Timothy J.; Katare, Rajesh K.; Jing, Naiyong; North, Diane; Peterson, Eric M.

    2017-02-14

    The present disclosure generally relates to durable solar mirror films, methods of making durable solar mirror films, and constructions including durable solar mirror films. In one embodiment, the present disclosure relates to a solar mirror film comprising: a multilayer optical film layer including having a coefficient of hygroscopic expansion of less than about 30 ppm per percent relative humidity; and a reflective layer having a coefficient of hygroscopic expansion.

  13. The Mirror Oscilloscpoe

    NARCIS (Netherlands)

    Goudriaan, B.

    2003-01-01

    This project is about designing and realizing an oscilloscope based on a laser beam reflected by two mirrors. The ¿Mirror Oscilloscope¿ uses two voice-coils actuators with mounted mirrors to reflect laser light, such that an image of a harmonic signal is projected on a projection screen. For trackin

  14. Water Cooled Mirror Design

    Energy Technology Data Exchange (ETDEWEB)

    Dale, Gregory E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Holloway, Michael Andrew [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Pulliam, Elias Noel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-03-30

    This design is intended to replace the current mirror setup being used for the NorthStar Moly 99 project in order to monitor the target coupon. The existing setup has limited movement for camera alignment and is difficult to align properly. This proposed conceptual design for a water cooled mirror will allow for greater thermal transfer between the mirror and the water block. It will also improve positioning of the mirror by using flexible vacuum hosing and a ball head joint capable of a wide range of motion. Incorporating this design into the target monitoring system will provide more efficient cooling of the mirror which will improve the amount of diffraction caused by the heating of the mirror. The process of aligning the mirror for accurate position will be greatly improved by increasing the range of motion by offering six degrees of freedom.

  15. Multilayer active shell mirrors for space telescopes

    Science.gov (United States)

    Steeves, John; Jackson, Kathryn; Pellegrino, Sergio; Redding, David; Wallace, J. Kent; Bradford, Samuel Case; Barbee, Troy

    2016-07-01

    A novel active mirror technology based on carbon fiber reinforced polymer (CFRP) substrates and replication techniques has been developed. Multiple additional layers are implemented into the design serving various functions. Nanolaminate metal films are used to provide a high quality reflective front surface. A backing layer of thin active material is implemented to provide the surface-parallel actuation scheme. Printed electronics are used to create a custom electrode pattern and flexible routing layer. Mirrors of this design are thin ( 100 μm PV) down to sub-micron precision. The system has been validated against several traditional techniques including photogrammetry and interferometry. The mirror performance has been characterized using this system, as well as closed-loop figure correction experiments on 150 mm dia. prototypes. The mirrors have demonstrated post-correction figure accuracies of 200 nm RMS (two dead actuators limiting performance).

  16. Coating considerations for mirrors of CPV devices

    Energy Technology Data Exchange (ETDEWEB)

    Schmauder, Torsten; Sauer, Peter; Ickes, Gerd [Leybold Optics GmbH, Siemensstr. 88, D-63755 Alzenau (Germany)

    2014-09-26

    One of the different optical concepts for concentrator devices is to place a focussing primary mirror behind a transparent front plate. In addition (also in case of Fresnel-diffractive main optics), further 'secondary' reflectors may be used further along the beam path. Such mirrors are usually implemented as coating stacks of a highly reflective metal - usually silver - and protective layers. The protective layers are preferably designed as reflection enhancing interference stack. The design of such protective layer stacks yields two difficulties, which are addressed in this paper: (a) vacuum coating of three-dimensional parts will result in a thickness distribution and the optical design of the stack should thus be tolerant to layer thickness variations, and (b) different places of the mirror will have different angle-of-incidence of the sunlight under operating conditions. As result, the layer stack has a different design at different places of the mirror.

  17. Ferrofluid Based Deformable Mirrors - a New Approach to Adaptive Optics Using Liquid Mirrors

    CERN Document Server

    Laird, P; Berube, V; Borra, E F; Ritcey, A; Rioux, M; Robitaille, N; Thibault, S; Yockell-Lelievre, H

    2002-01-01

    The trend towards ever larger telescopes and more advanced adaptive optics systems is driving the need for deformable mirrors with a large number of low cost actuators. Liquid mirrors have long been recognized a potential low cost alternative to conventional solid mirrors. By using a water or oil based ferrofluid we are able to benefit from a stronger magnetic response than is found in magnetic liquid metal amalgams and avoid the difficulty of passing a uniform current through a liquid. Depositing a thin silver colloid known as a metal liquid-like film (MELLF) on the ferrofluid surface solves the problem of low reflectivity of pure ferrofluids. This combination provides a liquid optical surface that can be precisely shaped in a magnetic field. We present experimental results obtained with a prototype deformable liquid mirror based on this combination.

  18. The MEL-X project at the Lawrence Livermore National Laboratory: a mirror-based delay line for x-rays

    Science.gov (United States)

    Pardini, Tom; Hill, Randy; Decker, Todd; Alameda, Jennifer; Soufli, Regina; Aquila, Andy; Guillet, Serge; Boutet, Sébastien; Hau-Riege, Stefan P.

    2015-09-01

    At the Lawrence Livermore National Laboratory (LLNL) in collaboration with the Linac Coherent Light Source (LCLS) we are developing a mirror-based delay line for x-rays (MEL-X) to enable x-ray pump/x-ray probe experiments at Free Electron Lasers (XFELs). The goal of this project is the development and deployment of a proof-of-principle delay line featuring coated x-ray optics. The four-mirror design of the MEL-X is motivated by the need for ease of alignment and use. In order to simplify the overlap of the pump and the probe beam after each delay time change, a scheme involving super-polished rails and mirror-to-motor decoupling has been adopted. The MEL-X, used in combination with a bright pulsed source like LCLS, features a capability for a high intensity pump beam. Its Iridium coating allows it to work at hard x-ray energies all the way up to 9 keV, with a probe beam transmission of 35% up to 8keV, and 14% at 9keV. The delay time can be tailored to each particular experiment, with a nominal range of 70 - 350 fs for this prototype. The MEL-X, combined with established techniques such as x-ray diffraction, absorption or emission, could provide new insights on ultra-fast transitions in highly excited states of matter.

  19. Optical fabrication of lightweighted 3D printed mirrors

    Science.gov (United States)

    Herzog, Harrison; Segal, Jacob; Smith, Jeremy; Bates, Richard; Calis, Jacob; De La Torre, Alyssa; Kim, Dae Wook; Mici, Joni; Mireles, Jorge; Stubbs, David M.; Wicker, Ryan

    2015-09-01

    Direct Metal Laser Sintering (DMLS) and Electron Beam Melting (EBM) 3D printing technologies were utilized to create lightweight, optical grade mirrors out of AlSi10Mg aluminum and Ti6Al4V titanium alloys at the University of Arizona in Tucson. The mirror prototypes were polished to meet the λ/20 RMS and λ/4 P-V surface figure requirements. The intent of this project was to design topologically optimized mirrors that had a high specific stiffness and low surface displacement. Two models were designed using Altair Inspire software, and the mirrors had to endure the polishing process with the necessary stiffness to eliminate print-through. Mitigating porosity of the 3D printed mirror blanks was a challenge in the face of reconciling new printing technologies with traditional optical polishing methods. The prototypes underwent Hot Isostatic Press (HIP) and heat treatment to improve density, eliminate porosity, and relieve internal stresses. Metal 3D printing allows for nearly unlimited topological constraints on design and virtually eliminates the need for a machine shop when creating an optical quality mirror. This research can lead to an increase in mirror mounting support complexity in the manufacturing of lightweight mirrors and improve overall process efficiency. The project aspired to have many future applications of light weighted 3D printed mirrors, such as spaceflight. This paper covers the design/fab/polish/test of 3D printed mirrors, thermal/structural finite element analysis, and results.

  20. Manufacturing of Lightweight Mirror

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Fabrication of the lightweight mirror is one of the key techniques for many large optical systems. CAD,CAM and CNC technologies are adopted in designing and manufacturing such mirrors in CIOMP. Better working efficiency and higher lightweight grade have been achieved. The results show that mirrors up to 70% weight reduction and 0.02λ(rms.) surface accuracy or better can be obtained.

  1. The mirror box

    Science.gov (United States)

    Thompson, Gene; Mathieson, Don

    2001-11-01

    The mirror box is an old standby in magic shows and an impressive demonstration of the law of reflection for the physics instructor. The box creates the illusion of an object floating in space by the use of a plane mirror.

  2. Corticospinal mirror neurons.

    Science.gov (United States)

    Kraskov, A; Philipp, R; Waldert, S; Vigneswaran, G; Quallo, M M; Lemon, R N

    2014-01-01

    Here, we report the properties of neurons with mirror-like characteristics that were identified as pyramidal tract neurons (PTNs) and recorded in the ventral premotor cortex (area F5) and primary motor cortex (M1) of three macaque monkeys. We analysed the neurons' discharge while the monkeys performed active grasp of either food or an object, and also while they observed an experimenter carrying out a similar range of grasps. A considerable proportion of tested PTNs showed clear mirror-like properties (52% F5 and 58% M1). Some PTNs exhibited 'classical' mirror neuron properties, increasing activity for both execution and observation, while others decreased their discharge during observation ('suppression mirror-neurons'). These experiments not only demonstrate the existence of PTNs as mirror neurons in M1, but also reveal some interesting differences between M1 and F5 mirror PTNs. Although observation-related changes in the discharge of PTNs must reach the spinal cord and will include some direct projections to motoneurons supplying grasping muscles, there was no EMG activity in these muscles during action observation. We suggest that the mirror neuron system is involved in the withholding of unwanted movement during action observation. Mirror neurons are differentially recruited in the behaviour that switches rapidly between making your own movements and observing those of others.

  3. Advanced Mirror Technology Development

    Science.gov (United States)

    Stahl, H. Philip

    2017-01-01

    The Advanced Mirror Technology Development (AMTD) project matures critical technologies required to enable ultra-stable 4-m-or-larger monolithic or segmented ultraviolet, optical, and infrared (UVOIR) space telescope primary-mirror assemblies for general astrophysics and ultra-high-contrast observations of exoplanets.

  4. Research and development of VUV optical coatings for micro mirror applications

    Institute of Scientific and Technical Information of China (English)

    Ming-hong Yang; Alexandre Gatto; Norbert Kaiser

    2005-01-01

    This paper deals with vacuum UV optical coatings for micro mirror applications. High reflecting low-stress optical coatings have been developed for the next-generation of micro mechanical mirrors. The optimized metal systems are applicable in the VUV spectral region and can be integrated in the technology of MOEMS, such as spatial light modulators (SLM) and micro scanning mirrors.

  5. The 8.2 metre primary mirrors of the VLT

    Science.gov (United States)

    Dierickx, P.; Enard, D.; Merkle, F.; Noethe, L.; Wilson, R. N.

    1990-08-01

    The Very Large Telescope (VLT) presently being developed at ESO is described in terms of technological advances which make its use both technically effective and feasible. The VLT capitalizes on advances in materials, polishing techniques, and mirror support systems. The VLT consists of four 8-m alt-az telescopes and a 2-m auxiliary telescope in a single-dish configuration with Zerodur meniscus mirrors passively supported on a lateral system. A discussion of the tradeoffs between glass and metal mirrors is presented, and computerized polishing is described in relation to optical specifications. The mirror is supported with 150 axial and 60 lateral supports with electromechanical actuators to modulate applied force. The active optics concept is employed via the flexibility of the primary mirror, which generates elastomechanical deformations and the position and orientation of the secondary mirror.

  6. Production and measurement of superpolished surfaces

    Science.gov (United States)

    van Wingerden, Johannes; Frankena, Hans J.; van der Zwan, Bertram A.

    1992-05-01

    The influence of polishing time on the roughness of ultrasmooth bowl-feed-polished surfaces is studied. A large improvement of the surface quality is obtained within the first 10 min, but increasing the polishing time from 10 to 60 min did not yield a significant difference. A Linnik interference microscope, adapted for phase-shifting interferometry, was used for roughness measurements. Preliminary measurements have been performed with a setup determining the scattered intensity within a small solid angle. This relatively simple setup, which is also suitable for uncoated glass surfaces, clearly showed the improvement of surface quality by bowl-feed polishing.

  7. Space Mirror Alignment System

    Science.gov (United States)

    Jau, Bruno M.; McKinney, Colin; Smythe, Robert F.; Palmer, Dean L.

    2011-01-01

    An optical alignment mirror mechanism (AMM) has been developed with angular positioning accuracy of +/-0.2 arcsec. This requires the mirror s linear positioning actuators to have positioning resolutions of +/-112 nm to enable the mirror to meet the angular tip/tilt accuracy requirement. Demonstrated capabilities are 0.1 arc-sec angular mirror positioning accuracy, which translates into linear positioning resolutions at the actuator of 50 nm. The mechanism consists of a structure with sets of cross-directional flexures that enable the mirror s tip and tilt motion, a mirror with its kinematic mount, and two linear actuators. An actuator comprises a brushless DC motor, a linear ball screw, and a piezoelectric brake that holds the mirror s position while the unit is unpowered. An interferometric linear position sensor senses the actuator s position. The AMMs were developed for an Astrometric Beam Combiner (ABC) optical bench, which is part of an interferometer development. Custom electronics were also developed to accommodate the presence of multiple AMMs within the ABC and provide a compact, all-in-one solution to power and control the AMMs.

  8. Mesmerising mirror neurons.

    Science.gov (United States)

    Heyes, Cecilia

    2010-06-01

    Mirror neurons have been hailed as the key to understanding social cognition. I argue that three currents of thought-relating to evolution, atomism and telepathy-have magnified the perceived importance of mirror neurons. When they are understood to be a product of associative learning, rather than an adaptation for social cognition, mirror neurons are no longer mesmerising, but they continue to raise important questions about both the psychology of science and the neural bases of social cognition. Copyright 2010 Elsevier Inc. All rights reserved.

  9. Minimal Mirror Twin Higgs

    CERN Document Server

    Barbieri, Riccardo; Harigaya, Keisuke

    2016-01-01

    In a Mirror Twin World with a maximally symmetric Higgs sector the little hierarchy of the Standard Model can be significantly mitigated, perhaps displacing the cutoff scale above the LHC reach. We show that consistency with observations requires that the Z2 parity exchanging the Standard Model with its mirror be broken in the Yukawa couplings. A minimal such effective field theory, with this sole Z2 breaking, can generate the Z2 breaking in the Higgs sector necessary for the Twin Higgs mechanism, and has constrained and correlated signals in invisible Higgs decays, direct Dark Matter Detection and Dark Radiation, all within reach of foreseen experiments. For dark matter, both mirror neutrons and a variety of self-interacting mirror atoms are considered. Neutrino mass signals and the effects of a possible additional Z2 breaking from the vacuum expectation values of B-L breaking fields are also discussed.

  10. The Athena Mirror

    Science.gov (United States)

    Wille, Eric

    2016-07-01

    The Athena mission (Advanced Telescope for High Energy Astrophysics) requires lightweight X-ray Wolter optics with a high angular resolution and large effective area. For achieving an effective area of 2 m^2 (at 1 keV) and an angular resolution of below 5 arcsec, the Silicon Pore Optics technology was developed by ESA together with a consortium of European industry. Silicon Pore Optics are made of commercial Si wafers using process technology adapted from the semiconductor industry. We present the current design of the Athena mirror concentrating on the technology development status of the Silicon Pore Optics, ranging from the manufacturing of single mirror plates towards complete focusing mirror modules and their integration into the mirror structure.

  11. Mirror reactor surface study

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, A. L.; Damm, C. C.; Futch, A. H.; Hiskes, J. R.; Meisenheimer, R. G.; Moir, R. W.; Simonen, T. C.; Stallard, B. W.; Taylor, C. E.

    1976-09-01

    A general survey is presented of surface-related phenomena associated with the following mirror reactor elements: plasma first wall, ion sources, neutral beams, director converters, vacuum systems, and plasma diagnostics. A discussion of surface phenomena in possible abnormal reactor operation is included. Several studies which appear to merit immediate attention and which are essential to the development of mirror reactors are abstracted from the list of recommended areas for surface work. The appendix contains a discussion of the fundamentals of particle/surface interactions. The interactions surveyed are backscattering, thermal desorption, sputtering, diffusion, particle ranges in solids, and surface spectroscopic methods. A bibliography lists references in a number of categories pertinent to mirror reactors. Several complete published and unpublished reports on surface aspects of current mirror plasma experiments and reactor developments are also included.

  12. Manufacturing parabolic mirrors

    CERN Multimedia

    CERN PhotoLab

    1975-01-01

    The photo shows the construction of a vertical centrifuge mounted on an air cushion, with a precision of 1/10000 during rotation, used for the manufacture of very high=precision parabolic mirrors. (See Annual Report 1974.)

  13. The obsidian mirror The obsidian mirror

    Directory of Open Access Journals (Sweden)

    Maria do Socorro Reis Amorin

    2008-04-01

    Full Text Available The author James Norman is an American who has always lived in Mexico during the summer. He seems to love Mexican - Indian traditions and he is well acquainted with the pre-historic culture as it is shown in his book: "The Obsidian Mirror". "The Obsidian Mirror" is a mysterious story about an archeologist: Quigley that lives in a small village in Mexico-San Marcos. He is searching for antiques that belong to some tribes of pre-historic Indians in order to find out their mysteries. Quigley becomes so engaged in his work that his mind has reached a stage that is impossible to separate between Quigley the archeologist, and Quigley as an ancient Indian. The culture, the myth, the sensation of Omen - characteristics of the Indians are within himself. As a result, Quigley acts sometimes as a real Indian. The author James Norman is an American who has always lived in Mexico during the summer. He seems to love Mexican - Indian traditions and he is well acquainted with the pre-historic culture as it is shown in his book: "The Obsidian Mirror". "The Obsidian Mirror" is a mysterious story about an archeologist: Quigley that lives in a small village in Mexico-San Marcos. He is searching for antiques that belong to some tribes of pre-historic Indians in order to find out their mysteries. Quigley becomes so engaged in his work that his mind has reached a stage that is impossible to separate between Quigley the archeologist, and Quigley as an ancient Indian. The culture, the myth, the sensation of Omen - characteristics of the Indians are within himself. As a result, Quigley acts sometimes as a real Indian.

  14. Optical Tests of Nanoengineered Liquid Mirrors

    CERN Document Server

    Yockell-Lelievre, H; Ritcey, A; Yockell-Lelievre, Helene; Borra, Ermanno F.; Ritcey, Anna; Jr, Lande Vieira da Silva

    2003-01-01

    We describe a new technology for the fabrication of inexpensive high-quality mirrors. We begin by chemically producing a large number of metallic nanoparticles coated with organic ligands. The particles are then spread on a liquid substrate where they self-assemble to give optical quality reflective surfaces. Since liquid surfaces can be modified with a variety of means (e.g. rotation, electromagnetic fields), this opens the possibility of making a new class of versatile and inexpensive optical elements that can have complex shapes which can be modified within short time scales. Interferometric measurements show optical quality surfaces. We have obtained reflectivity curves that show 80% peak reflectivities.We are confident that we can improve the reflectivity curves, for theoretical models predict higher values. We expect that nanoengineered liquid mirrors should be useful for scientific and engineering applications. The technology is interesting for large optics, such as large rotating parabolic mirrors, be...

  15. Plasma cleaning of beryllium coated mirrors

    Science.gov (United States)

    Moser, L.; Marot, L.; Steiner, R.; Newman, M.; Widdowson, A.; Ivanova, D.; Likonen, J.; Petersson, P.; Pintsuk, G.; Rubel, M.; Meyer, E.; Contributors, JET

    2016-02-01

    Cleaning systems of metallic first mirrors are needed in more than 20 optical diagnostic systems from ITER to avoid reflectivity losses. Currently, plasma sputtering is considered as one of the most promising techniques to remove deposits coming from the main wall (mainly beryllium and tungsten). This work presents the results of plasma cleaning of rhodium and molybdenum mirrors exposed in JET-ILW and contaminated with typical tokamak elements (including beryllium and tungsten). Using radio frequency (13.56 MHz) argon or helium plasma, the removal of mixed layers was demonstrated and mirror reflectivity improved towards initial values. The cleaning was evaluated by performing reflectivity measurements, scanning electron microscopy, x-ray photoelectron spectroscopy and ion beam analysis.

  16. Mirror contamination in space I: mirror modelling

    Science.gov (United States)

    Krijger, J. M.; Snel, R.; van Harten, G.; Rietjens, J. H. H.; Aben, I.

    2014-10-01

    We present a comprehensive model that can be employed to describe and correct for degradation of (scan) mirrors and diffusers in satellite instruments that suffer from changing optical Ultraviolet to visible (UV-VIS) properties during their operational lifetime. As trend studies become more important, so does the importance of understanding and correcting for this degradation. This is the case not only with respect to the transmission of the optical components, but also with respect to wavelength, polarisation, or scan-angle effects. Our hypothesis is that mirrors in flight suffer from the deposition of a thin absorbing layer of contaminant, which slowly builds up over time. We describe this with the Mueller matrix formalism and Fresnel equations for thin multi-layer contamination films. Special care is taken to avoid the confusion often present in earlier publications concerning the Mueller matrix calculus with out-of-plane reflections. The method can be applied to any UV-VIS satellite instrument. We illustrate and verify our approach to the optical behaviour of the multiple scan mirrors of SCIAMACHY (onboard ENVISAT).

  17. Electrochromic Mirrors With Variable Reflectance

    Science.gov (United States)

    Baucke, Friedrich G. K.

    1986-09-01

    Unstructured electrochromic mirrors with variable reflectance have been developed on the basis of hydrogen tungsten bronzes. The characteristic compounds of these devices are (1) solid ion-conducting layers ("electrolytes") resulting in only few micrometer thick all-solid-state systems, which can be enclosed between the substrate and a second glass plate and are thus protected from the environment, (2) integrated reflecting metal layers, and (3) hydrogen-storing electrochromic layers. Two basically different constructions are feasible. In "diffusion-driven" devices the bronze is formed (decomposed) by the chemical reaction x/2 H2+ W03⇔HxW03, in "field-driven" systems an electrochemical bronze formation (decomposition), x H + W03+ x e HxW03, takes place. The modes of construction are presented and compared, the electrochemistry of the thin layer cells involved is discussed, the prop-erties of devices according to the state of development are reported, and possible applications, e.g. as glare-free, inside and outside, automotive rear view mirrors with adjustable reflectance, are briefly described.

  18. Engineering and manufacturing of ITER first mirror mock-ups.

    Science.gov (United States)

    Joanny, M; Travère, J M; Salasca, S; Corre, Y; Marot, L; Thellier, C; Gallay, G; Cammarata, C; Passier, B; Fermé, J J

    2010-10-01

    Most of the ITER optical diagnostics aiming at viewing and monitoring plasma facing components will use in-vessel metallic mirrors. These mirrors will be exposed to a severe plasma environment and lead to an important tradeoff on their design and manufacturing. As a consequence, investigations are carried out on diagnostic mirrors toward the development of optimal and reliable solutions. The goals are to assess the manufacturing feasibility of the mirror coatings, evaluate the manufacturing capability and associated performances for the mirrors cooling and polishing, and finally determine the costs and delivery time of the first prototypes with a diameter of 200 and 500 mm. Three kinds of ITER candidate mock-ups are being designed and manufactured: rhodium films on stainless steel substrate, molybdenum on TZM substrate, and silver films on stainless steel substrate. The status of the project is presented in this paper.

  19. Design of a programmable spiral phase mirror

    CERN Document Server

    Bovino, Fabio Antonio; Bertolotti, Mario

    2011-01-01

    We designed a metallic programmable mirror for optical wavelengths made up of a large number of discrete steps which can be moved independently by actuators. The device is able to easily reshape an incident beam, imprinting on it an optical vortex with tunable topological charge and orbital angular momentum (OAM). Furthermore it is possible to generate almost arbitrary field profiles which can be used for spatial encoding.

  20. Multilayer Active Shell Mirrors for Space Telescopes

    OpenAIRE

    2016-01-01

    A novel active mirror technology based on carbon fiber reinforced polymer (CFRP) substrates and replication techniques has been developed. Multiple additional layers are implemented into the design serving various functions. Nanolaminate metal films are used to provide a high quality reflective front surface. A backing layer of thin active material is implemented to provide the surface-parallel actuation scheme. Printed electronics are used to create a custom electrode pattern and flexible ro...

  1. Surface micromachined scanning mirrors

    DEFF Research Database (Denmark)

    Mattsson, Kent Erik

    1992-01-01

    Both aluminum cantilever and torsional scanning mirrors have been fabricated and their static and dynamic properties are studied experimentally and theoretically. The experiments showed resonance frequencies in the range of 163 k-Hz - 632 kHz for cantilever beams with Q values between 5 and 11....... Torsional mirrors showed resonance frequencies in the range of 410 kHz - 667 kHz with Q values of 10 - 17. All measurements performed at atmospheric pressure. Both types of mechanical structures were deflected electrostatically at large angles (± 5°) more than 1011 times without breaking and without any...

  2. Unification with mirror fermions

    Directory of Open Access Journals (Sweden)

    Triantaphyllou George

    2014-04-01

    Full Text Available We present a new framework unifying interactions in nature by introducing mirror fermions, explaining the hierarchy between the weak scale and the coupling unification scale, which is found to lie close to Planck energies. A novel process leading to the emergence of symmetry is proposed, which not only reduces the arbitrariness of the scenario proposed but is also followed by significant cosmological implications. Phenomenology includes the probability of detection of mirror fermions via the corresponding composite bosonic states and the relevant quantum corrections at the LHC.

  3. Mirror neurons and mirror systems in monkeys and humans.

    Science.gov (United States)

    Fabbri-Destro, Maddalena; Rizzolatti, Giacomo

    2008-06-01

    Mirror neurons are a distinct class of neurons that transform specific sensory information into a motor format. Mirror neurons have been originally discovered in the premotor and parietal cortex of the monkey. Subsequent neurophysiological (TMS, EEG, MEG) and brain imaging studies have shown that a mirror mechanism is also present in humans. According to its anatomical locations, mirror mechanism plays a role in action and intention understanding, imitation, speech, and emotion feeling.

  4. Patterned gallium surfaces as molecular mirrors.

    Science.gov (United States)

    Bossi, Alessandra; Rivetti, Claudio; Mangiarotti, Laura; Whitcombe, Michael J; Turner, Anthony P F; Piletsky, Sergey A

    2007-09-30

    An entirely new means of printing molecular information on a planar film, involving casting nanoscale impressions of the template protein molecules in molten gallium, is presented here for the first time. The metallic imprints not only replicate the shape and size of the proteins used as template. They also show specific binding for the template species. Such a simple approach to the creation of antibody-like properties in metallic mirrors can lead to applications in separations, microfluidic devices, and the development of new optical and electronic sensors, and will be of interest to chemists, materials scientists, analytical specialists, and electronic engineers.

  5. Rearview Mirror Dimming Function

    Science.gov (United States)

    Layton, William

    2011-01-01

    Students are often unaware of the little tab on a rear-view mirror that is used to dim headlights from the rear. Those who know about this tab are usually interested in knowing how it works. Explanations of the optics involved can be found in Serway and Jewett and Jones and Edge. An alternate explanation is given.

  6. Rearview Mirror Dimming Function

    Science.gov (United States)

    Layton, William

    2011-01-01

    Students are often unaware of the little tab on a rear-view mirror that is used to dim headlights from the rear. Those who know about this tab are usually interested in knowing how it works. Explanations of the optics involved can be found in Serway and Jewett and Jones and Edge. An alternate explanation is given.

  7. Derived Categories of BHK Mirrors

    CERN Document Server

    Favero, David

    2016-01-01

    We prove a derived analogue to the results of Borisov, Clarke, Kelly, and Shoemaker on the birationality of Berglund-Hubsch-Krawitz mirrors. Heavily bootstrapping off work of Seidel and Sheridan, we obtain Homological Mirror Symmetry for Berglund-Hubsch-Krawitz mirror pencils to hypersurfaces in projective space.

  8. Mirror image agnosia.

    Science.gov (United States)

    Chandra, Sadanandavalli Retnaswami; Issac, Thomas Gregor

    2014-10-01

    Gnosis is a modality-specific ability to access semantic knowledge of an object or stimulus in the presence of normal perception. Failure of this is agnosia or disorder of recognition. It can be highly selective within a mode. self-images are different from others as none has seen one's own image except in reflection. Failure to recognize this image can be labeled as mirror image agnosia or Prosopagnosia for reflected self-image. Whereas mirror agnosia is a well-recognized situation where the person while looking at reflected images of other objects in the mirror he imagines that the objects are in fact inside the mirror and not outside. Five patients, four females, and one male presented with failure to recognize reflected self-image, resulting in patients conversing with the image as a friend, fighting because the person in mirror is wearing her nose stud, suspecting the reflected self-image to be an intruder; but did not have prosopagnosia for others faces, non living objects on self and also apraxias except dressing apraxia in one patient. This phenomena is new to our knowledge. Mirror image agnosia is an unique phenomena which is seen in patients with parietal lobe atrophy without specificity to a category of dementing illness and seems to disappear as disease advances. Reflected self-images probably have a specific neural substrate that gets affected very early in posterior dementias specially the ones which predominantly affect the right side. At that phase most patients are mistaken as suffering from psychiatric disorder as cognition is moderately preserved. As disease becomes more widespread this symptom becomes masked. A high degree of suspicion and proper assessment might help physicians to recognize the organic cause of the symptom so that early therapeutic interventions can be initiated. Further assessment of the symptom with FMRI and PET scan is likely to solve the mystery of how brain handles reflected self-images. A new observation involving failure

  9. Mirror image agnosia

    Directory of Open Access Journals (Sweden)

    Sadanandavalli Retnaswami Chandra

    2014-01-01

    Full Text Available Background: Gnosis is a modality-specific ability to access semantic knowledge of an object or stimulus in the presence of normal perception. Failure of this is agnosia or disorder of recognition. It can be highly selective within a mode. self-images are different from others as none has seen one′s own image except in reflection. Failure to recognize this image can be labeled as mirror image agnosia or Prosopagnosia for reflected self-image. Whereas mirror agnosia is a well-recognized situation where the person while looking at reflected images of other objects in the mirror he imagines that the objects are in fact inside the mirror and not outside. Material and Methods:: Five patients, four females, and one male presented with failure to recognize reflected self-image, resulting in patients conversing with the image as a friend, fighting because the person in mirror is wearing her nose stud, suspecting the reflected self-image to be an intruder; but did not have prosopagnosia for others faces, non living objects on self and also apraxias except dressing apraxia in one patient. This phenomena is new to our knowledge. Results: Mirror image agnosia is an unique phenomena which is seen in patients with parietal lobe atrophy without specificity to a category of dementing illness and seems to disappear as disease advances. Discussion: Reflected self-images probably have a specific neural substrate that gets affected very early in posterior dementias specially the ones which predominantly affect the right side. At that phase most patients are mistaken as suffering from psychiatric disorder as cognition is moderately preserved. As disease becomes more widespread this symptom becomes masked. A high degree of suspicion and proper assessment might help physicians to recognize the organic cause of the symptom so that early therapeutic interventions can be initiated. Further assessment of the symptom with FMRI and PET scan is likely to solve the mystery

  10. Bosonization and Mirror Symmetry

    CERN Document Server

    Kachru, Shamit; Torroba, Gonzalo; Wang, Huajia

    2016-01-01

    We study bosonization in 2+1 dimensions using mirror symmetry, a duality that relates pairs of supersymmetric theories. Upon breaking supersymmetry in a controlled way, we dynamically obtain the bosonization duality that equates the theory of a free Dirac fermion to QED3 with a single scalar boson. This duality may be used to demonstrate the bosonization duality relating an $O(2)$-symmetric Wilson-Fisher fixed point to QED3 with a single Dirac fermion, Peskin-Dasgupta-Halperin duality, and the recently conjectured duality relating the theory of a free Dirac fermion to fermionic QED3 with a single flavor. Chern-Simons and BF couplings for both dynamical and background gauge fields play a central role in our approach. In the course of our study, we describe a chiral mirror pair that may be viewed as the minimal supersymmetric generalization of the two bosonization dualities.

  11. Dynamic coherent backscattering mirror

    Energy Technology Data Exchange (ETDEWEB)

    Zeylikovich, I.; Xu, M., E-mail: mxu@fairfield.edu [Physics Department, Fairfield University, Fairfield, CT 06824 (United States)

    2016-02-15

    The phase of multiply scattered light has recently attracted considerable interest. Coherent backscattering is a striking phenomenon of multiple scattered light in which the coherence of light survives multiple scattering in a random medium and is observable in the direction space as an enhancement of the intensity of backscattered light within a cone around the retroreflection direction. Reciprocity also leads to enhancement of backscattering light in the spatial space. The random medium behaves as a reciprocity mirror which robustly converts a diverging incident beam into a converging backscattering one focusing at a conjugate spot in space. Here we first analyze theoretically this coherent backscattering mirror (CBM) phenomenon and then demonstrate the capability of CBM compensating and correcting both static and dynamic phase distortions occurring along the optical path. CBM may offer novel approaches for high speed dynamic phase corrections in optical systems and find applications in sensing and navigation.

  12. Dynamic coherent backscattering mirror

    Science.gov (United States)

    Xu, M.

    2016-01-01

    The phase of multiply scattered light has recently attracted considerable interest. Coherent backscattering is a striking phenomenon of multiple scattered light in which the coherence of light survives multiple scattering in a random medium and is observable in the direction space as an enhancement of the intensity of backscattered light within a cone around the retroreflection direction. Reciprocity also leads to enhancement of backscattering light in the spatial space. The random medium behaves as a reciprocity mirror which robustly converts a diverging incident beam into a converging backscattering one focusing at a conjugate spot in space. Here we first analyze theoretically this coherent backscattering mirror (CBM) phenomenon and then demonstrate the capability of CBM compensating and correcting both static and dynamic phase distortions occurring along the optical path. CBM may offer novel approaches for high speed dynamic phase corrections in optical systems and find applications in sensing and navigation. PMID:26937296

  13. Mirror Principle, 1

    CERN Document Server

    Lian Bong H; Yau, S T

    1997-01-01

    We propose and study the following Mirror Principle: certain sequences of multiplicative equivariant characteristic classes on Kontsevich's stable map moduli spaces can be computed in terms of certain hypergeometric type classes. As applications, we compute the equivariant Euler classes of obstruction bundles induced by any concavex bundles -- including any direct sum of line bundles -- on $\\P^n$. This includes proving the formula of Candelas-de la Ossa-Green-Parkes hence completing the program of Candelas et al, Kontesevich, Manin, and Givental, to compute rigorously the instanton prepotential function for the quintic in $\\P^4$. We derive, among many other examples, the multiple cover formula for Gromov-Witten invariants of $\\P^1$, computed earlier by Morrison-Aspinwall and by Manin in different approaches. We also prove a formula for enumerating Euler classes which arise in the so-called local mirror symmetry for some noncompact Calabi-Yau manifolds. At the end we interprete an infinite dimensional transfor...

  14. Bosonization and mirror symmetry

    Science.gov (United States)

    Kachru, Shamit; Mulligan, Michael; Torroba, Gonzalo; Wang, Huajia

    2016-10-01

    We study bosonization in 2 +1 dimensions using mirror symmetry, a duality that relates pairs of supersymmetric theories. Upon breaking supersymmetry in a controlled way, we dynamically obtain the bosonization duality that equates the theory of a free Dirac fermion to QED3 with a single scalar boson. This duality may be used to demonstrate the bosonization duality relating an O (2 )-symmetric Wilson-Fisher fixed point to QED3 with a single Dirac fermion, Peskin-Dasgupta-Halperin duality, and the recently conjectured duality relating the theory of a free Dirac fermion to fermionic QED3 with a single flavor. Chern-Simons and BF couplings for both dynamical and background gauge fields play a central role in our approach. In the course of our study, we describe a "chiral" mirror pair that may be viewed as the minimal supersymmetric generalization of the two bosonization dualities.

  15. Complex/Symplectic Mirrors

    CERN Document Server

    Chuang, W; Tomasiello, A; Chuang, Wu-yen; Kachru, Shamit; Tomasiello, Alessandro

    2005-01-01

    We construct a class of symplectic non--Kaehler and complex non--Kaehler string theory vacua, extending and providing evidence for an earlier suggestion by Polchinski and Strominger. The class admits a mirror pairing by construction. Comparing hints from a variety of sources, including ten--dimensional supergravity and KK reduction on SU(3)--structure manifolds, suggests a picture in which string theory extends Reid's fantasy to connect classes of both complex non-Kaehler and symplectic non-Kaehler manifolds.

  16. Carbon Fiber Mirror for a CubeSat Telescope

    Science.gov (United States)

    Kim, Young-Soo; Jang, Jeong Gyun; Kim, Jihun; Nam, Uk Won

    2017-08-01

    Telescope mirrors made by carbon fibers have been increasingly used especially for space applications, and they may replace the traditional glass mirrors. Glass mirrors are easy to fabricate, but needed to be carefully handled as they are brittle. Other materials have also been considered for telescope mirrors, such as metals, plastics, and liquids even. However glass and glass ceramics are still commonly and dominantly used.Carbon fiber has mainly been used for mechanical supports like truss structure and telescope tubes, as it is stiff and light-weight. It can also be a good material for telescope mirrors, as it has additional merits of non-brittle and very low thermal expansion. Therefore, carbon fiber mirror would be suitable for space telescopes which should endure the harsh vibration conditions during launch.A light-weight telescope made by carbon fiber has been designed for a small satellite which would have much less weight than conventional ones. In this poster, mirror materials are reviewed, and a design of carbon fiber telescope is presented and discussed.

  17. Structure modulated electrostatic deformable mirror for focus and geometry control.

    Science.gov (United States)

    Nam, Saekwang; Park, Suntak; Yun, Sungryul; Park, Bongje; Park, Seung Koo; Kyung, Ki-Uk

    2016-01-11

    We suggest a way to electrostatically control deformed geometry of an electrostatic deformable mirror (EDM) based on geometric modulation of a basement. The EDM is composed of a metal coated elastomeric membrane (active mirror) and a polymeric basement with electrode (ground). When an electrical voltage is applied across the components, the active mirror deforms toward the stationary basement responding to electrostatic attraction force in an air gap. Since the differentiated gap distance can induce change in electrostatic force distribution between the active mirror and the basement, the EDMs are capable of controlling deformed geometry of the active mirror with different basement structures (concave, flat, and protrusive). The modulation of the deformed geometry leads to significant change in the range of the focal length of the EDMs. Even under dynamic operations, the EDM shows fairly consistent and large deformation enough to change focal length in a wide frequency range (1~175 Hz). The geometric modulation of the active mirror with dynamic focus tunability can allow the EDM to be an active mirror lens for optical zoom devices as well as an optical component controlling field of view.

  18. A spectrum of shadowed mirroring.

    Science.gov (United States)

    Wanamaker, Melissa C

    2012-04-01

    The central focus of this paper is to explore and extend Kohut's theory of maternal mirroring and to place it within the current context of psychoanalytic thinking. Kohut believed a child must experience "positive" mirroring from his or her mother in infancy and beyond to ensure development of a healthy self. Kohut alludes, however, to a possible situation in which the mother's face, metaphorically a mirror, can appear "faceless" to her child. From this I have inferred the concept of what I shall call "shadowed mirroring." Clinical and literary examples show that distorted, "shadowed" mirroring appears on a spectrum, with passive mirroring at one end and hostile (either verbal or nonverbal) mirroring on the other; some individuals experience both. I then consider how "shadowed mirroring," especially hostile mirroring, can be understood within the twin contexts of the overall mother-child relationship and present-day Intersubjective/Relational thinking that is both bidirectional and co-constructed. Shadowed mirroring can lead to severe personality dysfunction along the borderline-narcissistic range, as well as to difficulties in the areas of identity formation, failure of self-cohesiveness, and the blunting of certain humane qualities like empathy.

  19. Mirrors fabricated with slightly oxidized C/C composites

    Science.gov (United States)

    Wang, Yongjie; Xu, Liang; Ding, Jiaoteng; Xie, Yongjie; Ma, Zhen

    2016-10-01

    Up to now, traditional materials, such as glass, metal and SiC ceramic, gradually begin to be unsatisfied development of the future mirrors. Designable carbon fiber reinforced composites became optimized material for large aperture lightweight mirrors. Carbon/carbon composites exhibit low thermal expansion and no moisture-absorption expansion problem, therefore, they get particular attention in the space reflector field. Ni was always employed as optical layer in the mirror, however, the coating behaved poor bond with substrate and often peeled off during optical processing. In order to solve this problem, slight oxidation was carried on the C/C composites before Ni plated. The Ni coating exhibited stronger coherence and better finish performance. Finally, a 100mm diameter plane mirror was successful fabricated.

  20. X-ray induced damage observations in ZERODUR mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Takacs, P.Z.; Furenlid, K.; Furenlid, L.

    1997-07-01

    Catastrophic damage has been observed in some ZERODUR mirrors used as first mirrors in two beam lines at the National Synchrotron Light Source (NSLS). Despite the high reflectivity of the coatings used on these mirrors, a significant flux of high energy photons penetrates below the coating and is absorbed in the substrate. Although model calculations indicate that the local temperature does not increase significantly, the authors suspect that over long time periods the absorbed flux produces structural changes in the material, leading to a build-up of surface stress, gross figure changes, and growth of fractures. These changes are probably related to the nature of the two-phase glass-ceramic composition of the ZERODUR material. Metal mirrors and single-phase materials do not exhibit such catastrophic damage under similar exposure conditions.

  1. Progress on high-performance rapid prototype aluminum mirrors

    Science.gov (United States)

    Woodard, Kenneth S.; Myrick, Bruce H.

    2017-05-01

    Near net shape parts can be produced using some very old processes (investment casting) and the relatively new direct metal laser sintering (DMLS) process. These processes have significant advantages for complex blank lightweighting and costs but are not inherently suited for producing high performance mirrors. The DMLS process can provide extremely complex lightweight structures but the high residual stresses left in the material results in unstable mirror figure retention. Although not to the extreme intricacy of DMLS, investment casting can also provide complex lightweight structures at considerably lower costs than DMLS and even conventional wrought mirror blanks but the less than 100% density for casting (and also DMLS) limits finishing quality. This paper will cover the progress that has been made to make both the DMLS and investment casting processes into viable near net shape blank options for high performance aluminum mirrors. Finish and figure results will be presented to show performance commensurate with existing conventional processes.

  2. Relating the "mirrorness" of mirror neurons to their origins.

    Science.gov (United States)

    Kilner, James M; Friston, Karl J

    2014-04-01

    Ever since their discovery, mirror neurons have generated much interest and debate. A commonly held view of mirror neuron function is that they transform "visual information into knowledge," thus enabling action understanding and non-verbal social communication between con-specifics (Rizzolatti & Craighero 2004). This functionality is thought to be so important that it has been argued that mirror neurons must be a result of selective pressure.

  3. SXI Prototype mirror mount

    Science.gov (United States)

    1995-01-01

    This final report describes the work performed from June 1993 to January 1995. The purpose of this contract was to provide optomechanical engineering and fabrication support to the Solar X-ray Imager (SXI) program in the areas of mirror, optical bench and camera assemblies of the telescope. The Center for Applied Optics (CAO) worked closely with the Optics and S&E technical staff of MSFC to develop and investigate the most viable and economical options for the design and fabrication of a number of parts for the various telescope assemblies. All the tasks under this delivery order have been successfully completed within budget and schedule.

  4. Look Into the Mirror

    Institute of Scientific and Technical Information of China (English)

    夏文虹

    2007-01-01

    Look into the mirror. Who is that girl I see, staring strange back at me? Is it a true myself or someone I have never known? Who am I? Why am I in this world? What am I going to do? So many times I questioned myself. I could never find a perfect answer. Why do I have to do such a lot of hard work? Why must I have so many exams? Why do I always read and read, write and write? Don't tell me it is the very life. Don't tell me these should be my happiness.

  5. Eavesdropping with a Mirror

    Institute of Scientific and Technical Information of China (English)

    JENNIFER LIM

    1994-01-01

    It was a custom in Yidu that on New Year’s Eve, people eavesdropped outside other people’s homes with a bronze mirror hidden in the bosom after reciting a rhyme to it. People believed that what they had heard would often fortell good or bad luck. A family named Zheng once lived in Yidu. The two sons of this family were both considered intellectuals, But the older son was eager to learn while the younger was lazy and sluggish. Their parents only liked the older son. Because of this, the old couple’s attitudes toward their two daughters-in-law were also

  6. Complex/Symplectic Mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Chuang, Wu-yen; Kachru, Shamit; /Stanford U., ITP /SLAC; Tomasiello, Alessandro; /Stanford U., ITP

    2005-10-28

    We construct a class of symplectic non-Kaehler and complex non-Kaehler string theory vacua, extending and providing evidence for an earlier suggestion by Polchinski and Strominger. The class admits a mirror pairing by construction. Comparing hints from a variety of sources, including ten-dimensional supergravity and KK reduction on SU(3)-structure manifolds, suggests a picture in which string theory extends Reid's fantasy to connect classes of both complex non-Kaehler and symplectic non-Kaehler manifolds.

  7. Mirror symmetry II

    CERN Document Server

    Greene, Brian R

    1997-01-01

    Mirror symmetry has undergone dramatic progress during the last five years. Tremendous insight has been gained on a number of key issues. This volume surveys these results. Some of the contributions in this work have appeared elsewhere, while others were written specifically for this collection. The areas covered are organized into 4 sections, and each presents papers by both physicists and mathematicians. This volume collects the most important developments that have taken place in mathematical physics since 1991. It is an essential reference tool for both mathematics and physics libraries and for students of physics and mathematics.

  8. Ronchi test for flat mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Estrada, N. [Instituto de Fisica, Universidad Autonoma de San Luis Potosi (Mexico); Engelfried, J. [Instituto de Fisica, Universidad Autonoma de San Luis Potosi (Mexico)]. E-mail: jurgen@ifisica.uaslp.mx; Morelos, A. [Instituto de Fisica, Universidad Autonoma de San Luis Potosi (Mexico)

    2005-11-11

    One of the RICHes in the velocity spectrometers of the proposed CKM experiment requires a flat mirror, situated in the high intensity kaon beam. To reduce the interaction background for the experiment, this mirror has to be as thin as possible. First glass prototypes were produced in Mexico. To test the surface quality of these prototypes, we extended the Ronchi method so flat mirrors can also be tested. We present the methods and report on results of our measurements.

  9. Focusing Mirror with Tunable Eccentricity

    CERN Document Server

    Stürmer, Moritz; Brunne, Jens; Wallrabe, Ulrike

    2013-01-01

    We present a new kind of varifocal mirror with independently adjustable curvatures in the major directions. For actuation we use two stacked piezo bending actuators with crossed in-plane polarization. This mirror can be used for example as an off-axis focusing device with tunable focal length and compensation for a variable angle of incidence or for coma correction. We demonstrate the prototype of such a mirror and characterize the mechanical deflection, as well as the focusing capabilities.

  10. Experimental investigation of circular Bragg phenomenon exhibited by a mirror-backed chiral sculptured thin film

    CERN Document Server

    Erten, Sema; Graham, Christian M; Lakhtakia, Akhlesh

    2015-01-01

    Experimentation with obliquely incident light established that all four circular reflectances of a chiral sculptured thin film backed by a metallic mirror contain strong evidence of the circular Bragg phenomenon. When the mirror is removed, strong evidence of that phenomenon is found only in the spectrum of the co-polarized and co-handed reflectance.

  11. Mirror development for CTA

    Science.gov (United States)

    Förster, A.; Doro, M.; Brun, P.; Canestrari, R.; Chadwick, P.; Font, L.; Ghigo, M.; Lorenz, E.; Mariotti, M.; Michalowski, J.; Niemiec, J.; Pareschi, G.; Peyaud, B.; Seweryn, K.

    2009-08-01

    The Cherenkov Telescope Array (CTA), currently in its early design phase, is a proposed new project for groundbased gamma-ray astronomy with at least 10 times higher sensitivity than current instruments. CTA is planned to consist of several tens of large Imaging Atmospheric Cherenkov Telescopes (IACTs) with a combined reflective surface of up to 10,000 m2. The challenge for the future CTA array is to develop lightweight and cost efficient mirrors with high production rates, good longterm durability and adequate optical properties. The technologies currently under investigation comprise different methods of carbon fibre/epoxy based substrates, sandwich concepts with cold-slumped surfaces made of thin float glass and different structural materials like aluminum honeycomb, glass foam or PU foam inside, and aluminum sandwich structures with either diamond milled surfaces or reflective foils. The current status of the mirror development for CTA will be summarized together with investigations on the improvement of the reflective surfaces and their protection against degradation.

  12. Quantum Radiation of Uniformly Accelerated Spherical Mirrors

    CERN Document Server

    Frolov, V

    2001-01-01

    We study quantum radiation generated by a uniformly accelerated motion of small spherical mirrors. To obtain Green's function for a scalar massless field we use Wick's rotation. In the Euclidean domain the problem is reduced to finding an electric potential in 4D flat space in the presence of a metallic toroidal boundary. The latter problem is solved by a separation of variables. After performing an inverse Wick's rotation we obtain the Hadamard function in the wave-zone regime and use it to calculate the vacuum fluctuations and the vacuum expectation for the energy density flux in the wave zone.

  13. Mirror Surface Grinding of Steel Bonded Carbides

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The steel bonded carbide, a composite material, is very difficult to be machined to a fine finish mirror surface. In this paper, an electrolytic in-process dressing (ELID) grinding with metallic bond super-hard abrasive wheel was developed for grinding steel bonded carbide GT35. Factors affecting ELID grinding performance were analyzed by an atomic force microscope (AFM). Based on the analysis of AFM topography of the fine ground mirror surface of the steel bonded carbide, a schematic diagram of the mechanism of micro-removal of the ground surface was described. The AFM topography also shows that the hard brittle carbide particles, on the surface of steel bonded carbide, were machined out by ductile cutting. Since the grinding cracks in the ground surface are due to temperature gradient, temperature distribution in the grinding area was analyzed by finite element method (FEM). Experimental results indicate that a good mirror surface with Ra<0.02pm can be obtained by the developed ELID grinding system.

  14. Mirrors Containing Biomimetic Shape-Control Actuators

    Science.gov (United States)

    Bar-Cohen, Yoseph; Mouroulis, Pantazis; Bao, Xiaoqi; Sherrit, Stewart

    2003-01-01

    Curved mirrors of a proposed type would comprise lightweight sheets or films containing integral, biologically inspired actuators for controlling their surface figures. These mirrors could be useful in such applications as collection of solar energy, focusing of radio beams, and (provided sufficient precision could be achieved) imaging. These mirrors were originally intended for use in outer space, but it should also be possible to develop terrestrial versions. Several prior NASA Tech Briefs articles have described a variety of approaches to the design of curved, lightweight mirrors containing integral shape-control actuators. The primary distinction between the present approach and the prior approaches lies in the actuator design concept, which involves shapes and movements reminiscent of those of a variety of small, multi-armed animals. The shape and movement of an actuator of this type can also be characterized as reminiscent of that of an umbrella. This concept can be further characterized as a derivative of that of multifinger grippers, the fingers of which are bimorph bending actuators (see Figure 1). The fingers of such actuators can be strips containing any of a variety of materials that have been investigated for use as actuators, including such electroactive polymers as ionomeric polymer/metal composites (IPMCs), ferroelectric polymers, and grafted elastomers. A mirror according to this proposal would be made from a sheet of one of the actuator composites mentioned above. The design would involve many variables, including the pre-curvature and stiffness of the mirror sheet, the required precision of figure control, the required range of variation in focal length (see Figure 2), the required precision of figure control for imaging or non-imaging use, the bending and twisting moments needed to effect the required deformations, and voltage-tomoment coefficients of the actuators, and the voltages accordingly required for actuation. A typical design would call

  15. Polishing technique for beryllium mirror

    Science.gov (United States)

    Froechtenigt, J. F.

    1976-01-01

    Performance tests, accomplished by inserting entire X ray telescope and polished mirror into vacuum line 67 m long and taking photographs of an X ray resolution source, indicate that polishing increases mirror efficiency from 0.06 percent for X rays at 0.8 nm and increases resolution from 15 to 3.75 arc-seconds.

  16. Plasma cleaning of ITER first mirrors in magnetic field

    CERN Document Server

    Moser, Lucas; Leipold, Frank; Reichle, Roger; Marot, Laurent; Meyer, Ernst

    2014-01-01

    To avoid reflectivity losses in ITER optical diagnostic systems, plasma sputtering of metallic First Mirrors is foreseen in order to remove deposits coming from the main wall (mainly beryllium and tungsten). Therefore plasma cleaning has to work on large mirrors (up to a size of 200*300 mm) and under the influence of strong magnetic fields (several Tesla). This work presents the results of plasma cleaning of aluminium and aluminium oxide (used as beryllium proxy) deposited on molybdenum mirrors. Using radio frequency (13.56 MHz) argon plasma, the removal of a 260 nm mixed aluminium/aluminium oxide film deposited by magnetron sputtering on a mirror (98 mm diameter) was demonstrated. 50 nm of pure aluminium oxide were removed from test mirrors (25 mm diameter) in a magnetic field of 0.35 T for various angles between the field lines and the mirrors surfaces. The cleaning efficiency was evaluated by performing reflectivity measurements, Scanning Electron Microscopy and X-ray Photoelectron Spectroscopy.

  17. Plasma cleaning of ITER First Mirrors in magnetic field

    Energy Technology Data Exchange (ETDEWEB)

    Moser, Lucas, E-mail: lucas.moser@unibas.ch [Department of Physics, University of Basel, Klingelbergstrasse 82, CH-4056 Basel (Switzerland); Steiner, Roland [Department of Physics, University of Basel, Klingelbergstrasse 82, CH-4056 Basel (Switzerland); Leipold, Frank; Reichle, Roger [ITER Organization, Route de Vinon-sur-Verdon, 13115 St Paul-lez-Durance (France); Marot, Laurent; Meyer, Ernst [Department of Physics, University of Basel, Klingelbergstrasse 82, CH-4056 Basel (Switzerland)

    2015-08-15

    To avoid reflectivity losses in ITER’s optical diagnostic systems, plasma sputtering of metallic First Mirrors is foreseen in order to remove deposits coming from the main wall (mainly beryllium and tungsten). Therefore plasma cleaning has to work on large mirrors (up to a size of 200 × 300 mm) and under the influence of strong magnetic fields (several Tesla). This work presents the results of plasma cleaning of aluminium and aluminium oxide (used as beryllium proxy) deposited on molybdenum mirrors. Using radio frequency (13.56 MHz) argon plasma, the removal of a 260 nm mixed aluminium/aluminium oxide film deposited by magnetron sputtering on a mirror (98 mm diameter) was demonstrated. 50 nm of pure aluminium oxide were removed from test mirrors (25 mm diameter) in a magnetic field of 0.35 T for various angles between the field lines and the mirrors surfaces. The cleaning efficiency was evaluated by performing reflectivity measurements, Scanning Electron Microscopy and X-ray Photoelectron Spectroscopy.

  18. Mirroring patients – or not

    DEFF Research Database (Denmark)

    Davidsen, Annette Sofie; Fosgerau, Christina Fogtmann

    2015-01-01

    on studies of imitative behaviour within linguistics and psychology, we argue that interactional mirroring is an important aspect of displaying implicit mentalization. We aimed to explore if, and in that case how, mirroring is displayed by general practitioners (GPs) and psychiatrists in consultations...... with patients with depression. We wanted to see how implicit mentalizing unfolds in physician–patient interactions. Consultations were videorecorded and analysed within the framework of conversation analysis. GPs and psychiatrists differed substantially in their propensity to mirror body movements and verbal...... and acoustic features of speech. GPs mirrored their patients more than psychiatrists in all modalities and were more flexible in their interactional behaviour. Psychiatrists seemed more static, regardless of the emotionality displayed by patients. Implicitly mirroring and attuning to patients could signify...

  19. Resonance MEMS mirrors design considerations

    Science.gov (United States)

    Sourani, S.

    2010-02-01

    Resonance MEMS mirrors are widely used today for many applications such as barcode scanners and personalprojectors. bTendo manufactures Personal Projection Engines on two types of mirrors: 1. Resonance mirrors for horizontal scanning 2. Linear mirrors for vertical scanning In this lecture we will discuss the "Energy Balance" and start-up conditions for resonance mirrors. We will derive the conditions for start-up as well as the predicted curve of θ(v): (see manuscript for equation) We will show simulation results in the time domain that prove the validity of the last equation. Finite element simulation could be used to calculate the comb capacitance and to predict the performance of a new structure.

  20. Shell Separation for Mirror Replication

    Science.gov (United States)

    1999-01-01

    NASA's Space Optics Manufacturing Center has been working to expand our view of the universe via sophisticated new telescopes. The Optics Center's goal is to develop low-cost, advanced space optics technologies for the NASA program in the 21st century - including the long-term goal of imaging Earth-like planets in distant solar systems. To reduce the cost of mirror fabrication, Marshall Space Flight Center (MSFC) has developed replication techniques, the machinery, and materials to replicate electro-formed nickel mirrors. Optics replication uses reusable forms, called mandrels, to make telescope mirrors ready for final finishing. MSFC optical physicist Bill Jones monitors a device used to chill a mandrel, causing it to shrink and separate from the telescope mirror without deforming the mirror's precisely curved surface.

  1. Transparent heat mirrors: influence of the materials on the optical characteristics.

    Science.gov (United States)

    Pracchia, J A; Simon, J M

    1981-01-15

    Transparent heat mirrors of the antireflecting metal type with a dielectric/metal/dielectric structure are studied. It is found that dielectrics of lower refractive index give a higher cutoff wavelength, but the transition becomes more gradual. The angular behavior of these mirrors is also analyzed. The optimum mechanical efficiency obtainable with a plain collector and a carnot engine is given for different concentrations and refractive indices. Moreover it appears that using Al instead of Ag introduces appreciable absorption losses (~25-35%).

  2. Mirror man: a case of skilled deliberate mirror writing.

    Science.gov (United States)

    McIntosh, Robert D; De Lucia, Natascia; Della Sala, Sergio

    2014-01-01

    Mirror writing is a striking behaviour that is common in children and can reemerge in adults following brain damage. Skilled deliberate mirror writing has also been reported, but only anecdotally. We provide the first quantitative study of skilled deliberate mirror writing. K.B. can write forward or backward, vertically upright or inverted, with the hands acting alone or simultaneously. K.B. is predominantly left handed, but writes habitually with his right hand. Of his writing formats, his left hand mirror writing is by far the most similar in style to his normal handwriting. When writing bimanually, he performs better when his two hands make mirror-symmetrical movements to write opposite scripts than if they move in the same direction to write similar scripts. He has no special facility for reading mirrored text. These features are consistent with prior anecdotal cases and support a motor basis for K.B.'s ability, according to which his skilled mirror writing results from the left hand execution of a low-level motor program for a right hand abductive writing action. Our methods offer a novel framework for investigating the sharing of motor representations across effectors.

  3. Advanced Mirror & Modelling Technology Development

    Science.gov (United States)

    Effinger, Michael; Stahl, H. Philip; Abplanalp, Laura; Maffett, Steven; Egerman, Robert; Eng, Ron; Arnold, William; Mosier, Gary; Blaurock, Carl

    2014-01-01

    The 2020 Decadal technology survey is starting in 2018. Technology on the shelf at that time will help guide selection to future low risk and low cost missions. The Advanced Mirror Technology Development (AMTD) team has identified development priorities based on science goals and engineering requirements for Ultraviolet Optical near-Infrared (UVOIR) missions in order to contribute to the selection process. One key development identified was lightweight mirror fabrication and testing. A monolithic, stacked, deep core mirror was fused and replicated twice to achieve the desired radius of curvature. It was subsequently successfully polished and tested. A recently awarded second phase to the AMTD project will develop larger mirrors to demonstrate the lateral scaling of the deep core mirror technology. Another key development was rapid modeling for the mirror. One model focused on generating optical and structural model results in minutes instead of months. Many variables could be accounted for regarding the core, face plate and back structure details. A portion of a spacecraft model was also developed. The spacecraft model incorporated direct integration to transform optical path difference to Point Spread Function (PSF) and between PSF to modulation transfer function. The second phase to the project will take the results of the rapid mirror modeler and integrate them into the rapid spacecraft modeler.

  4. LSST primary/tertiary monolithic mirror

    Science.gov (United States)

    Sebag, J.; Gressler, W.; Liang, M.; Neill, D.; Araujo-Hauck, C.; Andrew, J.; Angeli, G.; Cho, M.; Claver, C.; Daruich, F.; Gessner, C.; Hileman, E.; Krabbendam, V.; Muller, G.; Poczulp, G.; Repp, R.; Wiecha, O.; Xin, B.; Kenagy, K.; Martin, H. M.; Tuell, M. T.; West, S. C.

    2016-08-01

    At the core of the Large Synoptic Survey Telescope (LSST) three-mirror optical design is the primary/tertiary (M1M3) mirror that combines these two large mirrors onto one monolithic substrate. The M1M3 mirror was spin cast and polished at the Steward Observatory Mirror Lab at The University of Arizona (formerly SOML, now the Richard F. Caris Mirror Lab at the University of Arizona (RFCML)). Final acceptance of the mirror occurred during the year 2015 and the mirror is now in storage while the mirror cell assembly is being fabricated. The M1M3 mirror will be tested at RFCML after integration with its mirror cell before being shipped to Chile.

  5. Tandem mirror and field-reversed mirror experiments

    Energy Technology Data Exchange (ETDEWEB)

    Coensgen, F.H.; Simonen, T.C.; Turner, W.C.

    1979-08-21

    This paper is largely devoted to tandem mirror and field-reversed mirror experiments at the Lawrence Livermore Laboratory (LLL), and briefly summarizes results of experiments in which field-reversal has been achieved. In the tandem experiment, high-energy, high-density plasmas (nearly identical to 2XIIB plasmas) are located at each end of a solenoid where plasma ions are electrostatically confined by the high positive poentials arising in the end plug plasma. End plug ions are magnetically confined, and electrons are electrostatically confined by the overall positive potential of the system. The field-reversed mirror reactor consists of several small field-reversed mirror plasmas linked together for economic reasons. In the LLL Beta II experiment, generation of a field-reversed plasma ring will be investigated using a high-energy plasma gun with a transverse radial magnetic field. This plasma will be further heated and sustained by injection of intense, high-energy neutral beams.

  6. Back-surface gold mirrors for vibrationally resonant sum-frequency (VR-SFG) spectroscopy using 3-mercaptopropyltrimethoxysilane as an adhesion promoter.

    Science.gov (United States)

    Quast, Arthur D; Zhang, Feng; Linford, Matthew R; Patterson, James E

    2011-06-01

    Back-surface mirrors are needed as reference materials for vibrationally resonant sum-frequency generation (VR-SFG) probing of liquid-solid interfaces. Conventional noble metal mirrors are not suitable for back-surface applications due to the presence of a metal adhesion layer (chromium or titanium) between the window substrate and the reflective metal surface. Using vapor deposited 3-mercaptopropyltrimethoxysilane (MPTMS) as a bi-functional adhesion promoter, gold mirrors were fabricated on fused silica substrates. These mirrors exhibit excellent gold adhesion as determined by the Scotch(®) tape test. They also produce minimal spectroscopic interference in the C-H stretching region (2800-3000 cm(-1)), as characterized by VR-SFG. These mirrors are thus robust and can be used as back-surface mirrors for a variety of applications, including reference mirrors for VR-SFG.

  7. MIRROR MOVEMENT: A CASE REPORT

    Directory of Open Access Journals (Sweden)

    AA. Momen

    2008-11-01

    Full Text Available Mirror movement is an interesting but often overlooked neurological soft sign;these movements are described as simultaneous contralateral, involuntary, identical movements that accompany voluntary movements. This neurologic problem is very rarely seen in children; in familial cases there is a positive history of these movements in parents, diminishing with time. Here, we have presented the case of an 11-year old girl with mirror movements in her upper limbs which interfered with her hand writing. Her neurological examination revealed normal results. In this report, we have tried to explain some of the pathophysiologic mechanisms related to these abnormal movements.Keywords:Mirror Movements, Children, Soft neurologic sign

  8. Theta functions and mirror symmetry

    CERN Document Server

    Gross, Mark

    2012-01-01

    This is a survey covering aspects of varied work of the authors with Mohammed Abouzaid, Paul Hacking, and Sean Keel. While theta functions are traditionally canonical sections of ample line bundles on abelian varieties, we motivate, using mirror symmetry, the idea that theta functions exist in much greater generality. This suggestion originates with the work of the late Andrei Tyurin. We outline how to construct theta functions on the degenerations of varieties constructed in previous work of the authors, and then explain applications of this construction to homological mirror symmetry and constructions of broad classes of mirror varieties.

  9. Edificio Daily Mirror

    Directory of Open Access Journals (Sweden)

    Williams, Owen

    1963-07-01

    Full Text Available The building has 18 levels. The Press occupies the 4 basement floors. The ground floor is taken up with the entrance hall, and an indoor carriage way. A snack bar and the telephone operators are situated on the second floor. The production department and the medical services are located on the third storey, whilst the fourth is occupied by the offices and library. The fifth floor is the beginning of the higher section of the building. This floor and up to including the 11th floor are devoted to office space, except for the 10th storey, which contains the office apartments of the directors and the Council Chamber. Equipment related to various services of the building is housed on the 12th storey. Finally, this tall building constitutes a fine landmark in the London skyline. The Daily Mirror building is outstanding for the appropriate nature, the completeness and the quality of its installations, which thus provide the most widely read paper in the world with outstandingly efficient offices.Este edificio consta de 18 plantas. El cuerpo de Prensa se aloja en los cuatro sótanos; los vestíbulos de entrada y una calzada interior para vehículos se hallan en la planta baja; la primera alberga un snack-bar y centralita telefónica; la segunda, el departamento de producción y centro de asistencia médica, y la tercera, las oficinas y biblioteca principales. La cuarta planta señala el comienzo del bloque alto; esta planta, junto con las quinta, sexta, séptima, octava y décima, están dedicadas a oficinas. La novena contiene las oficinas-apartamentos de los directores y salas de Consejo, y la undécima, la maquinaria para las diversas instalaciones del edificio. La elevada torre constituye un grandioso hito de referencia en esta zona de Londres. El «Daily Mirror» se distingue por el acierto, número y perfección de sus instalaciones, que proporcionan, al periódico de mayor actualidad mundial, las más adecuadas y amplias oficinas modernas.

  10. Corrosion resistant solar mirror

    Energy Technology Data Exchange (ETDEWEB)

    Medwick, Paul A.; Abbott, Edward E.

    2016-07-19

    A reflective article includes a transparent substrate having a first major surface and a second major surface. A base coat is formed over at least a portion of the second major surface. A primary reflective coating having at least one metallic layer is formed over at least a portion of the base coat. A protective coating is formed over at least a portion of the primary reflective coating. The article further includes a solar cell and an anode, with the solar cell connected to the metallic layer and the anode.

  11. Engineering aspects of a fully mirrored endoscope

    Energy Technology Data Exchange (ETDEWEB)

    Terra, A., E-mail: a.terra@fz-juelich.de [Institute for Energy and Climate Research IEK-4 (Plasma Physics), Forschungszentrum Jülich GmbH, Assoc. EURATOM-FZJ, Member of the Trilateral Euregio Cluster, D-52425 Jülich (Germany); Huber, A.; Schweer, B.; Mertens, Ph. [Institute for Energy and Climate Research IEK-4 (Plasma Physics), Forschungszentrum Jülich GmbH, Assoc. EURATOM-FZJ, Member of the Trilateral Euregio Cluster, D-52425 Jülich (Germany); Arnoux, G.; Balshaw, N. [Euratom-CCFE Fusion Association, Culham Science Centre, Abingdon, OX14 3DB (United Kingdom); Brezinsek, S. [Institute for Energy and Climate Research IEK-4 (Plasma Physics), Forschungszentrum Jülich GmbH, Assoc. EURATOM-FZJ, Member of the Trilateral Euregio Cluster, D-52425 Jülich (Germany); Egner, S.; Hartl, M.; Kampf, D. [Kayser-Threde GmbH, D-81379 Munich (Germany); Klammer, J. [KRP-Mechatec Engineering GbR, D-85748 Garching (Germany); Lambertz, H.T. [Institute for Energy and Climate Research IEK-4 (Plasma Physics), Forschungszentrum Jülich GmbH, Assoc. EURATOM-FZJ, Member of the Trilateral Euregio Cluster, D-52425 Jülich (Germany); Morlock, C.; Murari, A. [EFDA-CSU, D-85748 Garching (Germany); Reindl, M. [KRP-Mechatec Engineering GbR, D-85748 Garching (Germany); Sanders, S. [Euratom-CCFE Fusion Association, Culham Science Centre, Abingdon, OX14 3DB (United Kingdom); Sergienko, G. [Institute for Energy and Climate Research IEK-4 (Plasma Physics), Forschungszentrum Jülich GmbH, Assoc. EURATOM-FZJ, Member of the Trilateral Euregio Cluster, D-52425 Jülich (Germany); Spencer, G. [Euratom-CCFE Fusion Association, Culham Science Centre, Abingdon, OX14 3DB (United Kingdom); and others

    2013-10-15

    Highlights: ► Replacement of JET diagnostics to match the new ITER-like Wall. ► The endoscope test ITER-like design with only mirror based optics. ► Withstanding and diagnostic capability during Plasma operation and disruptions. ► Engineering process from design to installation and procurement. -- Abstract: The development of optical diagnostics, like endoscopes, compatible with the ITER environment (metallic plasma facing components, neutron proof optics, etc.) is a challenge, but current tokamaks such as JET provide opportunities to test fully working concepts. This paper describes the engineering aspects of a fully mirrored endoscope that has recently been designed, procured and installed on JET. The system must operate in a very strict environment with high temperature, high magnetic fields up to B = 4 T and rapid field variations (∂B/∂t ∼ 100 T/s) that induce high stresses due to eddy currents in the front mirror assembly. It must be designed to withstand high mechanical loads especially during disruptions, which lead to acceleration of about 7 g at 14 Hz. For the JET endoscope, when the plasma thermal loading, direct and indirect, was added to the assumed disruption loads, the reserve factor, defined as a ratio of yield strength over summed up von Mises stresses, was close to 1 for the mirror components. To ensure reliable operation, several analyses were performed to evaluate the thermo-mechanical performance of the endoscope and a final validation was obtained from mechanical and thermal tests, before the system's final installation in May 2011. During the tests, stability of the field of view angle variation was kept below 1° despite the high thermal gradient on endoscope head (∂T/∂x ∼ 500 K/m). In parallel, to ensure long time operation and to prevent undesirable performance degradation, a shutter system was also implemented in order to reduce impurity deposition on in-vessel mirrors but also to allow in situ transmission

  12. Responder fast steering mirror

    Science.gov (United States)

    Bullard, Andrew; Shawki, Islam

    2013-10-01

    Raytheon Space and Airborne Systems (SAS) has designed, built and tested a 3.3-inch diameter fast steering mirror (FSM) for space application. This 2-axis FSM operates over a large angle (over 10 degree range), has a very high servo bandwidth (over 3.3 Khz closed loop bandwidth), has nanoradian-class noise, and is designed to support microradian class line of sight accuracy. The FSM maintains excellent performance over large temperature ranges (which includes wave front error) and has very high reliability with the help of fully redundant angle sensors and actuator circuits. The FSM is capable of achieving all its design requirements while also being reaction-compensated. The reaction compensation is achieved passively and does not need a separate control loop. The FSM has undergone various environmental testing which include exported forces and torques and thermal vacuum testing that support the FSM design claims. This paper presents the mechanical design and test results of the mechanism which satisfies the rigorous vacuum and space application requirements.

  13. Tinbergen on mirror neurons.

    Science.gov (United States)

    Heyes, Cecilia

    2014-01-01

    Fifty years ago, Niko Tinbergen defined the scope of behavioural biology with his four problems: causation, ontogeny, survival value and evolution. About 20 years ago, there was another highly significant development in behavioural biology-the discovery of mirror neurons (MNs). Here, I use Tinbergen's original four problems (rather than the list that appears in textbooks) to highlight the differences between two prominent accounts of MNs, the genetic and associative accounts; to suggest that the latter provides the defeasible 'best explanation' for current data on the causation and ontogeny of MNs; and to argue that functional analysis, of the kind that Tinbergen identified somewhat misleadingly with studies of 'survival value', should be a high priority for future research. In this kind of functional analysis, system-level theories would assign MNs a small, but potentially important, role in the achievement of action understanding-or another social cognitive function-by a production line of interacting component processes. These theories would be tested by experimental intervention in human and non-human animal samples with carefully documented and controlled developmental histories.

  14. Advanced Mirror Material System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Peregrine will bring together recent laboratory developments and mature the technology so that complete mirror and telescope assemblies can be reliably and robustly...

  15. Autism: Lost in the Mirror?

    Directory of Open Access Journals (Sweden)

    Alison Barry

    2015-01-01

    Full Text Available When I began my training as an analyst I took up a placement in an early intervention centre for autistic pre-scholars. The school was run on the psychological principles of ABA and children were tutored on a reward system promoting positive behaviors. Whilst working there I noticed that a number of children had a particular fascination for their mirrored image. This fascination was pervasive and many children would do their work primarily for the reward of the mirror. Through the lens of psychoanalysis I found this very interesting and Lacan’s Mirror Phase immediately came to mind and with this it bore the question as to whether or not there was something in the Mirror Phase of development that had an impact on what we see as symptoms of Autism.

  16. Fast Picometer Mirror Mount Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovation is a 6DOF controllable mirror mount with high dynamic range and fast tip/tilt capability for space based applications. It will enable the...

  17. Reflections on a Black Mirror

    CERN Document Server

    Good, Michael R R

    2016-01-01

    A black mirror is an accelerated boundary that produces particles in an exact correspondence to an evaporating black hole. We investigate the spectral dynamics of the particle creation during the formation process.

  18. Dielectric Coatings for IACT Mirrors

    CERN Document Server

    Förster, A; Chadwick, P; Held, M

    2013-01-01

    Imaging Atmospheric Cherenkov Telescopes for very-high energy gamma-ray astronomy need mirror with high reflectance roughly in the wavelength between 300 and 550 nm. The current standard reflective layer of such mirrors is aluminum. Being permanently exposed to the environment they show a constant degradation over the years. New and improved dielectric coatings have been developed to enhance their resistance to environmental impact and to extend their possible lifetime. In addition, these customized coatings have an increased reflectance of over 95% and are designed to significantly lower the night-sky background contribution. The development of such coatings for mirrors with areas up to 2 m2 and low application temperatures to suite the composite materials used for the new mirror susbtrates of the Cherenkov Telescope Array (CTA) and the results of extensive durability tests are presented.

  19. Loop-mirror-based slot waveguide refractive index sensor

    Directory of Open Access Journals (Sweden)

    Jun-long Kou

    2012-12-01

    Full Text Available Loop mirror has been widely used in fiber optical devices and systems for it provides a smart way to make use of the fiber birefringence properties and can enhance the sensitivity greatly. On the other hand, slot waveguide is very promising for optical sensing applications because of their peculiar spatial mode profile. In this paper, we propose and analyze a loop-mirror-based slot waveguide (LMSW sensor which can be routinely fabricated in modern high-volume complementary metal-oxide–semiconductor (CMOS process. The finite element method (FEM simulation results show that the birefringence can be as high as 0.8 which is orders of magnitude than that in conventional birefringent fiber loop mirror. High sensitivity up to 6 × 103 nm/RIU (refractive index unit is achieved by this scheme.

  20. Switchable mirrors based on nickel-magnesium films

    Energy Technology Data Exchange (ETDEWEB)

    Richardson,Thomas J.; Slack, Jonathan L.; Armitage, Robert D.; Kostecki, Robert; Farangis, Baker; Rubin, Michael D.

    2001-01-16

    A new type of electrochromic mirror electrode based on reversible uptake of hydrogen in nickel magnesium alloy films is reported. Thin,magnesium-rich Ni-Mg films prepared on glass substrates by cosputtering from Ni and Mg targets are mirror-like in appearance and have low visible transmittance. Upon exposure to hydrogen gas or on reduction in alkaline electrolyte, the films take up hydrogen and become transparent. When hydrogen is removed, the mirror properties are recovered. The transition is believed to result from reversible formation of Mg2NiH4 and MgH2. A thin overlayer of palladium was found to enhance the kinetics of hydrogen insertion and extraction,and to protect the metal surface against oxidation.

  1. Prototyping iridium coated mirrors for x-ray astronomy

    Science.gov (United States)

    Döhring, Thorsten; Probst, Anne-Catherine; Stollenwerk, Manfred; Emmerich, Florian; Stehlíková, Veronika; Inneman, Adolf

    2017-05-01

    X-ray astronomy uses space-based telescopes to overcome the disturbing absorption of the Eart&hacute;s atmosphere. The telescope mirrors are operating at grazing incidence angles and are coated with thin metal films of high-Z materials to get sufficient reflectivity for the high-energy radiation to be observed. In addition the optical payload needs to be light-weighted for launcher mass constrains. Within the project JEUMICO, an acronym for "Joint European Mirror Competence", the Aschaffenburg University of Applied Sciences and the Czech Technical University in Prague started a collaboration to develop mirrors for X-ray telescopes. The X-ray telescopes currently developed within this Bavarian- Czech project are of Lobster eye type optical design. Corresponding mirror segments use substrates of flat silicon wafers which are coated with thin iridium films, as this material is promising high reflectivity in the X-ray range of interest. The deposition of the iridium films is based on a magnetron sputtering process. Sputtering with different parameters, especially by variation of the argon gas pressure, leads to iridium films with different properties. In addition to investigations of the uncoated mirror substrates the achieved surface roughness has been studied. Occasional delamination of the iridium films due to high stress levels is prevented by chromium sublayers. Thereby the sputtering parameters are optimized in the context of the expected reflectivity of the coated X-ray mirrors. In near future measurements of the assembled mirror modules optical performances are planned at an X-ray test facility.

  2. Cost effective aluminum beryllium mirrors for critical optics applications

    Science.gov (United States)

    Say, Carissa; Duich, Jack; Huskamp, Chris; White, Ray

    2013-09-01

    The unique performance of aluminum-beryllium frequently makes it an ideal material for manufacturing precision optical-grade metal mirrors. Traditional methods of manufacture utilize hot-pressed powder block in billet form which is subsequently machined to final dimensions. Complex component geometries such as lightweighted, non-plano mirrors require extensive tool path programming, fixturing, and CNC machining time and result in a high buy-to-fly ratio (the ratio of the mass of raw material purchased to the mass of the finished part). This increases the cost of the mirror structure as a significant percentage of the procurement cost is consumed in the form of machining, tooling, and scrap material that do not add value to the final part. Inrad Optics, Inc. and IBC Advanced Alloys Corp. undertook a joint study to evaluate the suitability of investment-cast Beralcast® 191 and 363 aluminum-beryllium as a precision mirror substrate material. Net shape investment castings of the desired geometry minimizes machining to just cleanup stock, thereby reducing the recurring procurement cost while still maintaining performance. The thermal stability of two mirrors, (one each of Beralcast® 191 and Beralcast® 363), was characterized from -40°F to +150°F. A representative pocketed mirror was developed, including the creation of a relevant geometry and production of a cast component to validate the approach. Information from the demonstration unit was used as a basis for a comparative cost study of the representative mirror produced in Beralcast® and one machined from a billet of AlBeMet® 162 (AlBeMet® is a registered trademark of Materion Corporation). The technical and financial results of these studies will be discussed in detail.

  3. Coating Thin Mirror Segments for Lightweight X-ray Optics

    Science.gov (United States)

    Chan, Kai-Wing; Sharpe, Marton V.; Zhang, William; Kolosc, Linette; Hong, Melinda; McClelland, Ryan; Hohl, Bruce R.; Saha, Timo; Mazzarellam, James

    2013-01-01

    Next generations lightweight, high resolution, high throughput optics for x-ray astronomy requires integration of very thin mirror segments into a lightweight telescope housing without distortion. Thin glass substrates with linear dimension of 200 mm and thickness as small as 0.4 mm can now be fabricated to a precision of a few arc-seconds for grazing incidence optics. Subsequent implementation requires a distortion-free deposition of metals such as iridium or platinum. These depositions, however, generally have high coating stresses that cause mirror distortion. In this paper, we discuss the coating stress on these thin glass mirrors and the effort to eliminate their induced distortion. It is shown that balancing the coating distortion either by coating films with tensile and compressive stresses, or on both sides of the mirrors is not sufficient. Heating the mirror in a moderately high temperature turns out to relax the coated films reasonably well to a precision of about a second of arc and therefore provide a practical solution to the coating problem.

  4. Alignment Mirror Mechanisms for Space Use

    Science.gov (United States)

    Jau, Bruno M.; McKinney, Colin M.; Smythe, Robert F.; Palmer, Dean

    2011-01-01

    The paper describes an optical Alignment Mirror Mechanism (AMM), and discusses its control scheme. The mirror's angular positioning accuracy requirement is +/- 0.2 arc-sec. This requires the mirror's linear positioning actuators to have a positioning accuracy of +/- 109 nm to enable the mirror to meet the angular tip/tilt accuracy requirement. Demonstrated capabilities are +/- 35 nm linear positioning capability at the actuator, which translates into +/- 0.07 arc-sec angular mirror positioning accuracy.

  5. Dynamical manipulation of electromagnetic polarization using anisotropic meta-mirror

    Science.gov (United States)

    Cui, Jianhua; Huang, Cheng; Pan, Wenbo; Pu, Mingbo; Guo, Yinghui; Luo, Xiangang

    2016-07-01

    Polarization control of electromagnetic wave is very important in many fields. Here, we propose an active meta-mirror to dynamically manipulate electromagnetic polarization state at a broad band. This meta-mirror is composed of a double-layered metallic pattern backed by a metallic flat plate, and the active elements of PIN diodes are integrated into the meta-atom to control the reflection phase difference between two orthogonal polarization modes. Through switching the operating state of the PIN diodes, the meta-mirror is expected to achieve three polarization states which are left-handed, right-handed circular polarizations and linear polarization, respectively. We fabricated this active meta-mirror and validated its polarization conversion performance by measurement. The linearly polarized incident wave can be dynamically converted to right-handed or left-handed circular polarization in the frequency range between 3.4 and 8.8 GHz with the average loss of 1 dB. Furthermore, it also can keep its initial linear polarization state.

  6. More questions for mirror neurons.

    Science.gov (United States)

    Borg, Emma

    2013-09-01

    The mirror neuron system is widely held to provide direct access to the motor goals of others. This paper critically investigates this idea, focusing on the so-called 'intentional worry'. I explore two answers to the intentional worry: first that the worry is premised on too limited an understanding of mirror neuron behaviour (Sections 2 and 3), second that the appeal made to mirror neurons can be refined in such a way as to avoid the worry (Section 4). I argue that the first response requires an account of the mechanism by which small-scale gestures are supposedly mapped to larger chains of actions but that none of the extant accounts of this mechanism are plausible. Section 4 then briefly examines refinements of the mirror neuron-mindreading hypothesis which avoid the intentional worry. I conclude that these refinements may well be plausible but that they undermine many of the claims standardly made for mirror neurons. Copyright © 2012 Elsevier Inc. All rights reserved.

  7. Topological recursion and mirror curves

    CERN Document Server

    Bouchard, Vincent

    2012-01-01

    We study the constant contributions to the free energies obtained through the topological recursion applied to the complex curves mirror to toric Calabi-Yau threefolds. We show that the recursion reproduces precisely the corresponding Gromov-Witten invariants, which can be encoded in powers of the MacMahon function. As a result, we extend the scope of the "remodeling conjecture" to the full free energies, including the constant contributions. In the process we study how the pair of pants decomposition of the mirror curves plays an important role in the topological recursion. We also show that the free energies are not, strictly speaking, symplectic invariants, and that the recursive construction of the free energies does not commute with certain limits of mirror curves.

  8. Metrology of IXO Mirror Segments

    Science.gov (United States)

    Chan, Kai-Wing

    2011-01-01

    For future x-ray astrophysics mission that demands optics with large throughput and excellent angular resolution, many telescope concepts build around assembling thin mirror segments in a Wolter I geometry, such as that originally proposed for the International X-ray Observatory. The arc-second resolution requirement posts unique challenges not just for fabrication, mounting but also for metrology of these mirror segments. In this paper, we shall discuss the metrology of these segments using normal incidence metrological method with interferometers and null lenses. We present results of the calibration of the metrology systems we are currently using, discuss their accuracy and address the precision in measuring near-cylindrical mirror segments and the stability of the measurements.

  9. Alpha Channeling in Mirror Machines

    Energy Technology Data Exchange (ETDEWEB)

    Fisch N.J.

    2005-10-19

    Because of their engineering simplicity, high-β, and steady-state operation, mirror machines and related open-trap machines such as gas dynamic traps, are an attractive concept for achieving controlled nuclear fusion. In these open-trap machines, the confinement occurs by means of magnetic mirroring, without the magnetic field lines closing upon themselves within the region of particle confinement. Unfortunately, these concepts have not achieved to date very spectacular laboratory results, and their reactor prospects are dimmed by the prospect of a low Q-factor, the ratio of fusion power produced to auxiliary power. Nonetheless, because of its engineering promise, over the years numerous improvements have been proposed to enhance the reactor prospects of mirror fusion, such as tandem designs, end-plugging, and electric potential barriers.

  10. Optical and Durability Evaluation for Silvered Polymeric Mirrors and Reflectors: Cooperative Research and Development Final Report, CRADA Number, CRD-08-316

    Energy Technology Data Exchange (ETDEWEB)

    Gray, M.

    2014-08-01

    3M is currently developing silvered polymeric mirror reflectors as low-cost replacements for glass mirrors in concentrating solar power (CSP) systems. This effort is focused on development of reflectors comprising both metallized polymeric mirror films based on improved versions of ECP-305+ or other durable mirror film concepts and appropriate mechanically robust substrates. The objectives for this project are to reduce the system capital and operating costs and to lower the levelized cost of energy for CSP installations. The development of mirror reflectors involves work on both full reflectors and mirror films with and without coatings. Mirror reflectors must meet rigid optical specifications in terms of radius of curvature, slope errors and specularity. Mirror films must demonstrate long-term durability and maintain high reflectivity. 3M would like to augment internal capabilities to validate product performance with methods and tools developed at NREL to address these areas.

  11. Harmonic Distortion in CMOS Current Mirrors

    DEFF Research Database (Denmark)

    Bruun, Erik

    1998-01-01

    One of the origins of harmonic distortion in CMOS current mirrors is the inevitable mismatch between the MOS transistors involved. In this paper we examine both single current mirrors and complementary class AB current mirrors and develop an analytical model for the mismatch induced harmonic...... distortion. This analytical model is verified through simulations and is used for a discussion of the impact of mismatch on harmonic distortion properties of CMOS current mirrors. It is found that distortion levels somewhat below 1% can be attained by carefully matching the mirror transistors but ultra low...... distortion is not achievable with CMOS current mirrors...

  12. Composite single crystal silicon scan mirror substrates Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Single crystal silicon is a desirable mirror substrate for scan mirrors in space telescopes. As diameters of mirrors become larger, existing manufacturing...

  13. Deformable mirror with thermal actuators.

    Science.gov (United States)

    Vdovin, Gleb; Loktev, Mikhail

    2002-05-01

    Low-cost adaptive optics is applied in lasers, scientific instrumentation, ultrafast sciences, and ophthalmology. These applications demand that the deformable mirrors used be simple, inexpensive, reliable, and efficient. We report a novel type of ultralow-cost deformable mirror with thermal actuators. The device has a response time of ~5 s , an actuator stroke of ~6mum , and temporal stability of ~lambda/10 rms in the visible range and can be used for correction of rather large aberrations with slow-changing amplitude.

  14. NASA CONNECT: Algebra: Mirror, Mirror on the Universe

    Science.gov (United States)

    2000-01-01

    'Algebra: Mirror, Mirror on the Universe' is the last of seven programs in the 1999-2000 NASA CONNECT series. Produced by NASA Langley Research Center's Office of Education, NASA CONNECT is an award-winning series of instructional programs designed to enhance the teaching of math, science and technology concepts in grades 5-8. NASA CONNECT establishes the 'connection' between the mathematics, science, and technology concepts taught in the classroom and NASA research. Each program in the series supports the national mathematics, science, and technology standards; includes a resource-rich teacher guide; and uses a classroom experiment and web-based activity to complement and enhance the math, science, and technology concepts presented in the program. NASA CONNECT is FREE and the programs in the series are in the public domain. Visit our web site and register. http://connect.larc.nasa.gov In 'Algebra: Mirror, Mirror on the Universe', students will learn how algebra is used to explore the universe.

  15. Lightweight ZERODUR: Validation of Mirror Performance and Mirror Modeling Predictions

    Science.gov (United States)

    Hull, Tony; Stahl, H. Philip; Westerhoff, Thomas; Valente, Martin; Brooks, Thomas; Eng, Ron

    2017-01-01

    Upcoming spaceborne missions, both moderate and large in scale, require extreme dimensional stability while relying both upon established lightweight mirror materials, and also upon accurate modeling methods to predict performance under varying boundary conditions. We describe tests, recently performed at NASA's XRCF chambers and laboratories in Huntsville Alabama, during which a 1.2 m diameter, f/1.2988% lightweighted SCHOTT lightweighted ZERODUR(TradeMark) mirror was tested for thermal stability under static loads in steps down to 230K. Test results are compared to model predictions, based upon recently published data on ZERODUR(TradeMark). In addition to monitoring the mirror surface for thermal perturbations in XRCF Thermal Vacuum tests, static load gravity deformations have been measured and compared to model predictions. Also the Modal Response(dynamic disturbance) was measured and compared to model. We will discuss the fabrication approach and optomechanical design of the ZERODUR(TradeMark) mirror substrate by SCHOTT, its optical preparation for test by Arizona Optical Systems (AOS). Summarize the outcome of NASA's XRCF tests and model validations

  16. Timecourse of mirror and counter-mirror effects measured with transcranial magnetic stimulation

    Science.gov (United States)

    Cavallo, Andrea; Heyes, Cecilia; Becchio, Cristina; Bird, Geoffrey

    2014-01-01

    The human mirror system has been the subject of much research over the past two decades, but little is known about the timecourse of mirror responses. In addition, it is unclear whether mirror and counter-mirror effects follow the same timecourse. We used single-pulse transcranial magnetic stimulation to investigate the timecourse of mirror and counter-mirror responses in the human brain. Experiment 1 demonstrated that mirror responses can be measured from around 200 ms after observed action onset. Experiment 2 demonstrated significant effects of counter-mirror sensorimotor training at all timepoints at which a mirror response was found in Experiment 1 (i.e. from 200 ms onward), indicating that mirror and counter-mirror responses follow the same timecourse. By suggesting similarly direct routes for mirror and counter-mirror responses, these results support the associative account of mirror neuron origins whereby mirror responses arise as a result of correlated sensorimotor experience during development. More generally, they contribute to theorizing regarding mirror neuron function by providing some constraints on how quickly mirror responses can influence social cognition. PMID:23709352

  17. [The ontogeny of the mirror neuron system].

    Science.gov (United States)

    Myowa-Yamakoshi, Masako

    2014-06-01

    Abstract Humans utilize the mirror neuron system to understand and predict others' actions. However, the ontogeny of the mirror neuron system remains unknown. Whether mirror neuron function is an innate trait or whether mirror neurons acquire their sensorimotor matching properties ontogenetically remains to be clarified. In this paper, I review the ontogenetic theory of the mirror neuron system. I then discuss the functioning of the mirror neuron system in the context of social cognitive abilities, which are unique to humans. Recently, some researchers argue that it is too early to interpret the function of mirror neurons as an understanding of the underlying psychological states of others. They imply that such functioning would require inferential cognitive processes that are known to involve areas outside the mirror neuron system. Filling in this missing link may be the key to elucidating the unique ability of humans to understand others' actions.

  18. MIRROR THERAPY: A REVIEW OF EVIDENCES

    Directory of Open Access Journals (Sweden)

    Aishath Najiha

    2015-06-01

    Full Text Available The aim of this review was to identify and summarize the existing evidences on mirror box therapy for the management of various musculoskeletal conditions. A systemic literature search was performed to identify studies concerning mirror therapy. The included journal articles were reviewed and assessed for its significance. Fifty one studies were identified and reviewed. Five different patient categories were studied: 24 studies focussed on mirror therapy after stroke, thirteen studies focussed on mirror therapy after an amputation, three studies focussed on mirror therapy with complex regional pain syndrome patients, two studies on mirror therapy for cerebral palsy and one study focussed on mirror therapy after a fracture. The articles reviewed showed a trend that mirror therapy is effective in stroke, phantom limb pain, complex regional pain syndrome, cerebral palsy and fracture rehabilitation.

  19. Mirror with thermally controlled radius of curvature

    Science.gov (United States)

    Neil, George R.; Shinn, Michelle D.

    2010-06-22

    A radius of curvature controlled mirror for controlling precisely the focal point of a laser beam or other light beam. The radius of curvature controlled mirror provides nearly spherical distortion of the mirror in response to differential expansion between the front and rear surfaces of the mirror. The radius of curvature controlled mirror compensates for changes in other optical components due to heating or other physical changes. The radius of curvature controlled mirror includes an arrangement for adjusting the temperature of the front surface and separately adjusting the temperature of the rear surface to control the radius of curvature. The temperature adjustment arrangements can include cooling channels within the mirror body or convection of a gas upon the surface of the mirror. A control system controls the differential expansion between the front and rear surfaces to achieve the desired radius of curvature.

  20. Tiny Mirrors Make TV Magic

    Institute of Scientific and Technical Information of China (English)

    杨仲言

    1994-01-01

    By mounting thousands of miniature mirrors atop a silicon chip, a Texas Instruments engineer has crafted a TV display technology that can produce brighter and larger pictures than ever before. Since their invention, televisions have relied on cathode-ray tubes for their displays. These generate images by spraying electrons onto the back of

  1. Mounting and Alignment of IXO Mirror Segments

    Science.gov (United States)

    Chan, Kai-Wing; Zhang, William; Evans, Tyler; McClelland, Ryan; Hong, Melinda; Mazzarella, James; Saha, Timo; Jalota, Lalit; Olsen, Lawrence; Byron, Glenn

    2010-01-01

    A suspension-mounting scheme is developed for the IXO (International X-ray Observatory) mirror segments in which the figure of the mirror segment is preserved in each stage of mounting. The mirror, first fixed on a thermally compatible strongback, is subsequently transported, aligned and transferred onto its mirror housing. In this paper, we shall outline the requirement, approaches, and recent progress of the suspension mount processes.

  2. The Axisymmetric Tandem Mirror: A Magnetic Mirror Concept Game Changer Magnet Mirror Status Study Group

    Energy Technology Data Exchange (ETDEWEB)

    Simonen, T; Cohen, R; Correll, D; Fowler, K; Post, D; Berk, H; Horton, W; Hooper, E B; Fisch, N; Hassam, A; Baldwin, D; Pearlstein, D; Logan, G; Turner, B; Moir, R; Molvik, A; Ryutov, D; Ivanov, A A; Kesner, J; Cohen, B; McLean, H; Tamano, T; Tang, X Z; Imai, T

    2008-10-24

    Experimental results, theory and innovative ideas now point with increased confidence to the possibility of a Gas Dynamic Trap (GDT) neutron source which would be on the path to an attractively simple Axisymmetric Tandem Mirror (ATM) power plant. Although magnetic mirror research was terminated in the US 20 years ago, experiments continued in Japan (Gamma 10) and Russia (GDT), with a very small US effort. This research has now yielded data, increased understanding, and generated ideas resulting in the new concepts described here. Early mirror research was carried out with circular axisymmetric magnets. These plasmas were MHD unstable due to the unfavorable magnetic curvature near the mid-plane. Then the minimum-B concept emerged in which the field line curvature was everywhere favorable and the plasma was situated in a MHD stable magnetic well (70% average beta in 2XII-B). The Ioffe-bar or baseball-coil became the standard for over 40 years. In the 1980's, driven by success with minimum-B stabilization and the control of ion cyclotron instabilities in PR6 and 2XII-B, mirrors were viewed as a potentially attractive concept with near-term advantages as a lower Q neutron source for applications such as a hybrid fission fuel factory or toxic waste burner. However there are down sides to the minimum-B geometry: coil construction is complex; restraining magnetic forces limit field strength and mirror ratios. Furthermore, the magnetic field lines have geodesic curvature which introduces resonant and neoclassical radial transport as observed in early tandem mirror experiments. So what now leads us to think that simple axisymmetric mirror plasmas can be stable? The Russian GDT experiment achieves on-axis 60% beta by peaking of the kinetic plasma pressure near the mirror throat (where the curvature is favorable) to counter-balance the average unfavorable mid-plane curvature. Then a modest augmentation of plasma pressure in the expander results in stability. The GDT

  3. Moss monitoring as a mirror of land use? Nitrogen and metal accumulation in mosses of two regions in middle Europe; Moosmonitoring als Spiegel der Landnutzung? Stickstoff- und Metallakkumulation in Moosen zweier Regionen Mitteleuropas

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, W.; Hornsmann, I.; Pesch, R.; Schmidt, G. [Hochschule Vechta (Germany). Lehrstuhl fuer Landschaftsoekologie; Fraenzle, S.; Wuenschmann, S.; Heidenreich, H.; Markert, B. [Internationales Hochschulinstitut, Zittau (Germany)

    2008-02-15

    Goal, Scope and Background. The study was conducted to test the hypothesis that the regional variability of nitrogen (N) and metal accumulations in terrestrial ecosystems are due to historical and recent ways of land use. To this end, in two regions of Central Europe the metal and N accumulations in both regions should be examined by comparative moss analysis. The regions should be of quantitatively specified representativity for selected ecological characteristics of Europe. Within both regions these characteristics should be covered by the sites where the moss samples were collected. The number of samples should allow for geostatistical estimation of the measured nitrogen and metal loads. Results. By use of the ecological regionalisation of Europe the Weser-Ems Region (WER) and the Euro Region Nissa (ERN) were selected for investigation. The sampling sites represent quite well the natural landscapes and the land use categories of both regions. The measurement values corroborate the decline of metal accumulation observed since the beginning of the European Mosses Monitoring Survey in 1990. The metal loads of the mosses in the ERN exceed those in the WER significantly. The opposite holds true for the N concentrations: those in the WER are significantly higher than those in the ERN. (orig.)

  4. Mirror movements in progressive hemifacial atrophy

    OpenAIRE

    2015-01-01

    Mirror movements are simultaneous, involuntary, identical movements occurring during contralateral voluntary movements. These movements are considered as soft neurologic signs seen uncommonly in clinical practice. The mirror movements are described in various neurological disorders which include parkinsonism, cranio veretebral junction anamolies, and hemiplegic cerebral palsy. These movements are intriguing and can pose significant disability. However, no such observation regarding mirror mov...

  5. Through the looking-glass: mirror reading.

    Science.gov (United States)

    Duñabeitia, Jon Andoni; Molinaro, Nicola; Carreiras, Manuel

    2011-02-14

    At early stages of object identification we process correctly oriented and mirrored versions of an object similarly. However, in letter and word perception, such tolerance to mirror reversals is harmful for efficient reading. Do readers successfully develop blindness mechanisms for mirror-letters and words? We conducted two masked priming experiments while recording participants' electrophysiological brain responses to briefly presented primes including mirror-letters (Experiment 1) or to shortly presented mirror-words (Experiment 2). Results showed that the human visual word recognition system is not totally blind to mirror-letters and mirror-words, since the early stages of processing mirror-letters and mirror-words produced effects on target word recognition that were highly similar to the effects produced by identical primes (N250 component). In a posterior stage of processing (N400 epoch), the effect of mirror-letters and mirror-words was different from the effect of identical primes, even though reversed primes still elicited N400 priming effects different from unrelated primes. These results demonstrate that readers perceive mirror-letters and words as correct at initial stages of word recognition, and that the visual word recognition system's neural representation is grounded on basic principles that govern object perception.

  6. Light Weight Silicon Mirrors for Space Instrumentation

    Science.gov (United States)

    Bly, Vincent T.; Hill, Peter C.; Hagopian, John G.; Strojay, Carl R.; Miller, Timothy

    2012-01-01

    Each mirror is a monolithic structure from a single crystal of silicon. The mirrors are light weighted after the optical surface is ground and polished. Mirrors made during the initial phase of this work were typically 1/50 lambda or better (RMS at 633 n m)

  7. The mirror neuron system : New frontiers

    NARCIS (Netherlands)

    Keysers, Christian; Fadiga, Luciano

    2008-01-01

    Since the discovery of mirror neurons, much effort has been invested into Studying their location and properties in the human brain. Here we review these original findings and introduce the Main topics of this special issue of Social Neuroscience. What does the mirror system code? How is the mirror

  8. Controllable Curved Mirrors Made from Single-Layer EAP Films

    Science.gov (United States)

    Bao, Xiaoqi; Bar-Cohen, Yoseph; Sherrit, Stewart

    2004-01-01

    A document proposes that lightweight, deployable, large-aperture, controllable curved mirrors made of reflectively coated thin electroactive-polymer (EAP) films be developed for use in spaceborne microwave and optical systems. In these mirrors, the EAP films would serve as both structures and actuators. EAPs that are potentially suitable for such use include piezoelectric, electrostrictive, ferroelectric, and dielectric polymers. These materials exhibit strains proportional to the squares of applied electric fields. Utilizing this phenomenon, a curved mirror according to the proposal could be made from a flat film, upon which a nonuniform electrostatic potential (decreasing from the center toward the edge) would be imposed to obtain a required curvature. The effect would be analogous to that of an old-fashioned metalworking practice in which a flat metal sheet is made into a bowl by hammering it repeatedly, the frequency of hammer blows decreasing with distance from the center. In operation, the nonuniform electrostatic potential could be imposed by use of an electron gun. Calculations have shown that by use of a single- layer film made of a currently available EAP, it would be possible to control the focal length of a 2-m-diameter mirror from infinity to 1.25 m.

  9. Phase-Controlled Magnetic Mirror for Wavefront Correction

    Science.gov (United States)

    Hagopian, John; Wollack, Edward

    2011-01-01

    Typically, light interacts with matter via the electric field and interaction with weakly bound electrons. In a magnetic mirror, a patterned nanowire is fabricated over a metallic layer with a dielectric layer in between. Oscillation of the electrons in the nanowires in response to the magnetic field of incident photons causes a re-emission of photons and operation as a "magnetic mirror." By controlling the index of refraction in the dielectric layer using a local applied voltage, the phase of the emitted radiation can be controlled. This allows electrical modification of the reflected wavefront, resulting in a deformable mirror that can be used for wavefront control. Certain applications require wavefront quality in the few-nanometer regime, which is a major challenge for optical fabrication and alignment of mirrors or lenses. The use of a deformable magnetic mirror allows for a device with no moving parts that can modify the phase of incident light over many spatial scales, potentially with higher resolution than current approaches. Current deformable mirrors modify the incident wavefront by using nano-actuation of a substrate to physically bend the mirror to a desired shape. The purpose of the innovation is to modify the incident wavefront for the purpose of correction of fabrication and alignment-induced wavefront errors at the system level. The advanced degree of precision required for some applications such as gravity wave detection (LISA - Laser Interferometer Space Antenna) or planet finding (FKSI - Fourier-Kelvin Stellar Interferometer) requires wavefront control at the limits of the current state of the art. All the steps required to fabricate a magnetic mirror have been demonstrated. The modification is to apply a bias voltage to the dielectric layer so as to change the index of refraction and modify the phase of the reflected radiation. Light is reflected off the device and collected by a phase-sensing interferometer. The interferometer determines the

  10. 同步辐射中双压电片反射镜的研究现状∗%Present research status of piezo electric bimorph mirrors in synchrotron radiation sources

    Institute of Scientific and Technical Information of China (English)

    张瑶; 汤善治; 李明; 王立超; 高俊祥

    2016-01-01

    between the interfaces of PZT-PZT, while two continuous ground electrodes are located between the interfaces of Si-PZT. The PZTs that are polarized normally to their surface, any voltage applied across the bimorph results in a different change of the lateral dimensions of two PZTs, thereby leading to a bending of the whole structure. The relationship between the curvature of the bending mirror and voltage is given. In the third part of this paper, the technical issues as well as the design concepts are discussed in detail. Several Si-PZT-PZT-Si bimorph mirrors are first fabricated and tested by ESRF. The dimensions of each of them are 150 mm in length, 40–45 mm in width, and 15–18 mm in thickness. PZT is selected as an active material because of its high coupling factor, high piezoelectric coefficient, and high Curie temperature. The faceplates need to be easy to polishsuch as silicon and silica. Owing to the symmetrical layered structure Si-PZT-PZT-Si, the mirror is less sensitive to temperature variations from the process of bonding and polishing. The bimorph mirrors are confirmed to be promising by experimental tests. As the state-of-art polishing technique, elastic emission machining (EEM) becomes available commercially, and diamond light source brings EEM into the bimorph mirror to achieve a novel adaptive X-ray mirror coupling adaptive zonal control with a super-smooth surface. This super-polished adaptive mirror becomes the first optics with a bendable ellipse with sub-nanometer figure error. Spring-8 fabricates an adaptive mirror with different structures, and two strips of PZTs are glued to the side faces of the mirror. This mirror shows a diffraction-limited performance. Finally, the wavefront measuring methods and control algorithm are introduced. Wavefront measuring devices used in the metrology cleanroom include long trace profiler, nanometer optics component measuring machine, and interferometer. At-wavelength measuring methods used on the beamline

  11. Steps toward increasing Q in mirror systems

    Energy Technology Data Exchange (ETDEWEB)

    Post, R.F.

    1979-08-20

    Experiments such as the 2XIIB experiment at Livermore have established the ability of mirror systems to confine high temperature, high density plasmas at central beta values exceeding unity. Given these results the next tasks for the mirror approach are to explore means for increasing the energy gain factor Q and to scale up the plasma volume, both of these requirements deriving from economic constraints. This report discusses means for increasng Q, including recent improvements in the tandem mirror concept and design studies of the field-reversed mirror in the context of upcoming and proposed scaled-up mirror experiments.

  12. [What mirror neurons have revealed: revisited].

    Science.gov (United States)

    Murata, Akira; Maeda, Kazutaka

    2014-06-01

    The first paper on mirror neurons was published in 1992. In the span of over two decades since then, much knowledge about the relationship between social cognitive function and the motor control system has been accumulated. Direct matching of visual actions and their corresponding motor representations is the most important functional property of mirror neuron. Many studies have emphasized intrinsic simulation as a core concept for mirror neurons. Mirror neurons are thought to play a role in social cognitive function. However, the function of mirror neurons in the macaque remains unclear, because such cognitive functions are limited or lacking in macaque monkeys. It is therefore important to discuss these neurons in the context of motor function. Rizzolatti and colleagues have stressed that the most important function of mirror neurons in macaques is recognition of actions performed by other individuals. I suggest that mirror neurons in the Macaque inferior pariental lobule might be correlated with body schema. In the parieto-premotor network, matching of corollary discharge and actual sensory feedback is an essential neuronal operation. Recently, neurons showing mirror properties were found in some cortical areas outside the mirror neuron system. The current work would revisit the outcomes of mirror neuron studies to discuss the function of mirror neurons in the monkey.

  13. Mirror neurons: their implications for group psychotherapy.

    Science.gov (United States)

    Schermer, Victor L

    2010-10-01

    Recently discovered mirror neurons in the motor cortex of the brain register the actions and intentions of both the organism and others in the environment. As such, they may play a significant role in social behavior and groups. This paper considers the potential implications of mirror neurons and related neural networks for group therapists, proposing that mirror neurons and mirror systems provide "hard-wired" support for the group therapist's belief in the centrality of relationships in the treatment process and exploring their value in accounting for group-as-a-whole phenomena. Mirror neurons further confirm the holistic, social nature of perception, action, and intention as distinct from a stimulus-response behaviorism. The implications of mirror neurons and mirroring processes for the group therapist role, interventions, and training are also discussed.

  14. Design of a rapidly cooled cryogenic mirror

    Science.gov (United States)

    Plummer, Ron; Hsu, Ike

    1993-01-01

    The paper discusses the design, analysis, and testing of a rapidly cooled beryllium cryogenic mirror, which is the primary mirror in the four-element optical system for the Long Wavelength Infrared Advanced Technology Seeker. The mirror is shown to meet the requirement of five minutes for cooling to cryogenic operating temperature; it also maintains its optical figure and vacuum integrity and meets the nuclear specification. Results of a detailed thermal analysis on the mirror showed that, using nitrogen gas at 80 K as coolant, the front face of the mirror can be cooled from an initial temperature of 300 K to less than 90 K within five minutes. In a vacuum chamber, using liquid nitrogen as coolant, the mirror can be cooled to 80 K within 1.5 min. The mirror is well thermally insulated, so that it can be maintained at less than its operating temperature for a long time without active cooling.

  15. Improved cylindrical mirror energy analyzer

    Science.gov (United States)

    Baranova, L. A.

    2017-03-01

    A study has been carried out of the electron-optical properties of improved design of the cylindrical mirror energy analyzer. Both external and internal electrodes of the analyzer are divided into three isolated parts, whereby the potentials on the individual parts can be regulated independently from each other. In symmetric operating mode at identical potentials on the side parts of the electrodes, a significant increase has been obtained in resolving power and light-gathering power of the analyzer compared to the standard design of the cylindrical mirror. In asymmetric operating mode, which is implemented in a linear potential distribution on the external electrode, the conditions have been found under which the linear dispersion of the analyzer increases several times.

  16. Spectral Theory and Mirror Symmetry

    CERN Document Server

    Marino, Marcos

    2015-01-01

    Recent developments in string theory have revealed a surprising connection between spectral theory and local mirror symmetry: it has been found that the quantization of mirror curves to toric Calabi-Yau threefolds leads to trace class operators, whose spectral properties are conjecturally encoded in the enumerative geometry of the Calabi-Yau. This leads to a new, infinite family of solvable spectral problems: the Fredholm determinants of these operators can be found explicitly in terms of Gromov-Witten invariants and their refinements; their spectrum is encoded in exact quantization conditions, and turns out to be determined by the vanishing of a quantum theta function. Conversely, the spectral theory of these operators provides a non-perturbative definition of topological string theory on toric Calabi-Yau threefolds. In particular, their integral kernels lead to matrix integral representations of the topological string partition function, which explain some number-theoretic properties of the periods. In this...

  17. ZERODUR for stress mirror polishing

    Science.gov (United States)

    Jedamzik, Ralf; Kunisch, Clemens; Westerhoff, Thomas

    2011-09-01

    Stress mirror polishing is considered as one of several polishing technologies for the generation of the aspherical shaped primary mirror segments of the thirty meter telescope (TMT). For stress mirror polishing it is essential to precisely know the elastic response of glass ceramic substrate materials under a given deformation load. In the past it was experimentally shown that glass ceramics do not respond instantaneously to loading and unloading conditions, this effect was called "delayed elasticity." Recently SCHOTT has shown that it is possible to use a model to predict the characteristic thermal expansion behaviour of individual ZERODUR® batches for a given temperature profile. A similar approach will be used to predict the delayed elastic behavior of ZERODUR® under time dependent loads. In this presentation the delayed elasticity effect of ZERODUR® is reviewed. The delayed elastic response of the material to load conditions is shown and discussed. First results of a model approach based on experimental results and tools that have been built up for the modelling of the delayed elasticity effect of ZERODUR® will be presented.

  18. Mirror agnosia and the mirrored-self misidentification delusion: a hypnotic analogue.

    Science.gov (United States)

    Connors, Michael H; Cox, Rochelle E; Barnier, Amanda J; Langdon, Robyn; Coltheart, Max

    2012-05-01

    Mirrored-self misidentification is the delusional belief that one's reflection in the mirror is a stranger. Current theories suggest that one pathway to the delusion is mirror agnosia (a deficit in which patients are unable to use mirror knowledge when interacting with mirrors). This study examined whether a hypnotic suggestion for mirror agnosia can recreate features of the delusion. Ten high hypnotisable participants were given either a suggestion to not understand mirrors or to see the mirror as a window. Participants were asked to look into a mirror and describe what they saw. Participants were tested on their understanding of mirrors and received a series of challenges. Participants then received a detailed postexperimental inquiry. Three of five participants given the suggestion to not understand mirrors reported seeing a stranger and maintained this belief when challenged. These participants also showed signs of mirror agnosia. No participants given the suggestion to see a window reported seeing a stranger. Results indicate that a hypnotic suggestion for mirror agnosia can be used to recreate the mirrored-self misidentification delusion. Factors influencing the effectiveness of hypnotic analogues of psychopathology, such as participants' expectations and interpretations, are discussed.

  19. Efficient manufacturing technology of metal optics

    Science.gov (United States)

    Zhang, Jizhen; Wu, Yanxiong; Zhang, Xin; Zhang, Liping; Wang, Lingjie; Qu, Hemeng

    2015-10-01

    The efficient manufacturing technologies greatly accelerate the development and production process. Optical components have higher precision requirements than mechanical parts. This provides great challenge for rapid manufacturing. Metallic optical system is featured high resolution, wide spectral range, light weight, compact design, low cost and short manufacturing period. Reflective mirrors and supporting structures can be made from the same material to improve athermal performance of the system. Common materials for metal mirrors in optical applications include aluminum, copper, beryllium, aluminum beryllium alloy and so on. Their physical characteristics and relative advantages are presented. Most kinds of metals have good machinability and can be manufactured by many kinds of producing methods. This makes metallic optical system saving 30%~60% cost and time than others. The manufacturing process of metal mirror is different due to its working spectral. The metal mirror can be directly manufactured by single point diamond turning. This is an outstanding technique in point of ultra-precision as well as economical manufacture of mirrors. The roughness values and form accuracy of optical surfaces after diamond turning can satisfy the quality level for applications in the near infrared and infrared range. And for visible light spectral the turning structures must be removed with a smoothing procedure in order to minimize the scatter losses. Some smoothing methods to obtain visible quality metal mirrors are given in this paper. Some new manufacturing technology, such as 3D printing, can be used for metallic optical system and several promising techniques are presented.

  20. Mirror Metrology Using Nano-Probe Supports

    Science.gov (United States)

    Robinson, David; Hong, Maoling; Byron, Glenn; McClelland, Ryan; Chan, Kai-Wing

    2012-01-01

    Thin, lightweight mirrors are needed for future x-ray space telescopes in order to increase x-ray collecting area while maintaining a reduced mass and volume capable of being launched on existing rockets. However, it is very difficult to determine the undistorted shape of such thin mirrors because the mounting of the mirror during measurement causes distortion. Traditional kinematic mounts have insufficient supports to control the distortion to measurable levels and prevent the mirror from vibrating during measurement. Over-constrained mounts (non-kinematic) result in an unknown force state causing mirror distortion that cannot be determined or analytically removed. In order to measure flexible mirrors, it is necessary to over-constrain the mirror. Over-constraint causes unknown distortions to be applied to the mirror. Even if a kinematic constraint system can be used, necessary imperfections in the kinematic assumption can lead to an unknown force state capable of distorting the mirror. Previously, thicker, stiffer, and heavier mirrors were used to achieve low optical figure distortion. These mirrors could be measured to an acceptable level of precision using traditional kinematic mounts. As lighter weight precision optics have developed, systems such as the whiffle tree or hydraulic supports have been used to provide additional mounting supports while maintaining the kinematic assumption. The purpose of this invention is to over-constrain a mirror for optical measurement without causing unacceptable or unknown distortions. The invention uses force gauges capable of measuring 1/10,000 of a Newton attached to nano-actuators to support a thin x-ray optic with known and controlled forces to allow for figure measurement and knowledge of the undeformed mirror figure. The mirror is hung from strings such that it is minimally distorted and in a known force state. However, the hanging mirror cannot be measured because it is both swinging and vibrating. In order to

  1. Mirror-Symmetric Matrices and Their Application

    Institute of Scientific and Technical Information of China (English)

    李国林; 冯正和

    2002-01-01

    The well-known centrosymmetric matrices correctly reflect mirror-symmetry with no component or only one component on the mirror plane. Mirror-symmetric matrices defined in this paper can represent mirror-symmetric structures with various components on the mirror plane. Some basic properties of mirror-symmetric matrices were studied and applied to interconnection analysis. A generalized odd/even-mode decomposition scheme was developed based on the mirror reflection relationship for mirror-symmetric multiconductor transmission lines (MTLs). The per-unit-length (PUL) impedance matrix Z and admittance matrix Y can be divided into odd-mode and even-mode PUL matrices. Thus the order of the MTL system is reduced from n to k and k+p, where p(≥0)is the conductor number on the mirror plane. The analysis of mirror-symmetric matrices is related to the theory of symmetric group, which is the most effective tool for the study of symmetry.

  2. Reflectivity-modulated grating-mirror

    DEFF Research Database (Denmark)

    2012-01-01

    The invention relates to vertical cavity lasers (VCL) incorporating a reflectivity-modulated grating mirror (1) for modulating the laser output. A cavity is formed by a bottom mirror (4), an active region (3), and an outcoupling top grating mirror (1) formed by a periodic refractive index grating...... to the oscillation axis. A modulated voltage (91) is applied in reverse bias between the n- and p-doped layers to modulate the refractive index of the electrooptic material layer (12) and thereby the reflectivity spectrum of the grating mirror (1). The reflectivity of the grating mirror (1) can be modulated between...... a reflectivity with little or no out coupling and a reflectivity with normal out coupling, wherein lasing in the VCL is supported at both the first and the second reflectivity. As the out coupling mirror modulates the output, the lasing does not need to be modulated, and the invention provides the advantage...

  3. Standard specification for silvered flat glass mirror

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2008-01-01

    1.1 This specification covers the requirements for silvered flat glass mirrors of rectangular shape supplied as cut sizes, stock sheets or as lehr ends and to which no further processing (such as edgework or other fabrication) has been done. 1.2 This specification covers the quality requirements of silvered annealed monolithic clear and tinted flat glass mirrors up to 6 mm (¼ in.) thick. The mirrors are intended to be used indoors for mirror glazing, for components of decorative accessories or for similar uses. 1.3 This specification does not address safety glazing materials nor requirements for mirror applications. Consult model building codes and other applicable standards for safety glazing applications. 1.4 Mirrors covered in this specification are not intended for use in environments where high humidity or airborne corrosion promoters, or both, are consistently present (such as swimming pool areas, ocean-going vessels, chemical laboratories and other corrosive environments). 1.5 The dimensional val...

  4. Mirror Development for the Cherenkov Telescope Array

    CERN Document Server

    Förster, A; Baba, H; Bähr, J; Bonardi, A; Bonnoli, G; Brun, P; Canestrari, R; Chadwick, P; Chikawa, M; Carton, P -H; De Souza, V; Dipold, J; Doro, M; Durand, D; Dyrda, M; Giro, E; Glicenstein, J -F; Hanabata, Y; Hayashida, M; Hrabovski, M; Jeanney, C; Kagaya, M; Katagiri, H; Lessio, L; MANDAT, D; Mariotti, M; Medina, C; Michałowski, J; Micolon, P; Nakajima, D; Niemiec, J; Nozato, A; Palatka, M; Pareschi, G; Pech, M; Peyaud, B; Pühlhofer, G; Rataj, M; Rodeghiero, G; Rojas, G; Rousselle, J; Sakonaka, R; Schovanek, P; Seweryn, K; Schultz, C; Shu, S; Stinzing, F; Stodulski, M; Teshima, M; Travniczek, P; Van Eldik, C; Vassiliev, V; Wiśniewski, Ł; Wörnlein, A; Yoshida, T

    2013-01-01

    The Cherenkov Telescope Array (CTA) is a planned observatory for very-high energy gamma-ray astronomy. It will consist of several tens of telescopes of different sizes, with a total mirror area of up to 10,000 square meters. Most mirrors of current installations are either polished glass mirrors or diamond-turned aluminium mirrors, both labour intensive technologies. For CTA, several new technologies for a fast and cost-efficient production of light-weight and reliable mirror substrates have been developed and industrial pre-production has started for most of them. In addition, new or improved aluminium-based and dielectric surface coatings have been developed to increase the reflectance over the lifetime of the mirrors compared to those of current Cherenkov telescope instruments.

  5. Deformable mirrors development program at ESO

    Science.gov (United States)

    Stroebele, Stefan; Vernet, Elise; Brinkmann, Martin; Jakob, Gerd; Lilley, Paul; Casali, Mark; Madec, Pierre-Yves; Kasper, Markus

    2016-07-01

    Over the last decade, adaptive optics has become essential in different fields of research including medicine and industrial applications. With this new need, the market of deformable mirrors has expanded a lot allowing new technologies and actuation principles to be developed. Several E-ELT instruments have identified the need for post focal deformable mirrors but with the increasing size of the telescopes the requirements on the deformable mirrors become more demanding. A simple scaling up of existing technologies from few hundred actuators to thousands of actuators will not be sufficient to satisfy the future needs of ESO. To bridge the gap between available deformable mirrors and the future needs for the E-ELT, ESO started a development program for deformable mirror technologies. The requirements and the path to get the deformable mirrors for post focal adaptive optics systems for the E-ELT is presented.

  6. Mirror QCD and Cosmological Constant

    CERN Document Server

    Pasechnik, Roman; Teryaev, Oleg

    2016-01-01

    An analog of Quantum Chromo Dynamics (QCD) sector known as mirror QCD (mQCD) can affect the cosmological evolution and help in resolving the Cosmological Constant problem. In this work, we explore an intriguing possibility for a compensation of the negative QCD vacuum contribution to the ground state energy density of the universe by means of a positive contribution from the chromomagnetic gluon condensate in mQCD. The trace anomaly compensation condition and the form of the mQCD coupling constant in the infrared limit have been proposed by analysing a partial non-perturbative solution of the Einstein--Yang-Mills equations of motion.

  7. Tandem mirror technology demonstration facility

    Energy Technology Data Exchange (ETDEWEB)

    1983-10-01

    This report describes a facility for generating engineering data on the nuclear technologies needed to build an engineering test reactor (ETR). The facility, based on a tandem mirror operating in the Kelley mode, could be used to produce a high neutron flux (1.4 MW/M/sup 2/) on an 8-m/sup 2/ test area for testing fusion blankets. Runs of more than 100 h, with an average availability of 30%, would produce a fluence of 5 mW/yr/m/sup 2/ and give the necessary experience for successful operation of an ETR.

  8. Inhomogeneous interface laser mirror coatings.

    Science.gov (United States)

    Ledger, A M

    1979-09-01

    Methods of improving the durability of thin-film laser mirror coatings for 10.6 microm using thorium fluoride, zinc selenide, and zinc sulfide materials have been investigated. The largest improvement in film durability was obtained by using inhomogeneous interface fabrication for all the dielectric-dielectric interfaces and by incorporating cerium fluoride protective overcoating material into the film design. Experimental results are given for enhanced reflectors, polarization-selective coatings, and buried-grating aperture-sharing coatings designed for high-power laser applications.

  9. Mirror averaging with sparsity priors

    CERN Document Server

    Dalalyan, Arnak

    2010-01-01

    We consider the problem of aggregating the elements of a (possibly infinite) dictionary for building a decision procedure, that aims at minimizing a given criterion. Along with the dictionary, an independent identically distributed training sample is available, on which the performance of a given procedure can be tested. In a fairly general set-up, we establish an oracle inequality for the Mirror Averaging aggregate based on any prior distribution. This oracle inequality is applied in the context of sparse coding for different problems of statistics and machine learning such as regression, density estimation and binary classification.

  10. Transport phenomena in stochastic magnetic mirrors

    OpenAIRE

    Malyshkin, Leonid; Kulsrud, Russell

    2000-01-01

    Parallel thermal conduction along stochastic magnetic field lines may be reduced because the heat conducting electrons become trapped and detrapped between regions of strong magnetic field (magnetic mirrors). The problem reduces to a simple but realistic model for diffusion of mono-energetic electrons based on the fact that when there is a reduction of diffusion, it is controlled by a subset of the mirrors, the principle mirrors. The diffusion reduction can be considered as equivalent to an e...

  11. Pulse compression by use of deformable mirrors.

    Science.gov (United States)

    Zeek, E; Maginnis, K; Backus, S; Russek, U; Murnane, M; Mourou, G; Kapteyn, H; Vdovin, G

    1999-04-01

    An electrostatically deformable, gold-coated, silicon nitride membrane mirror was used as a phase modulator to compress pulses from 92 to 15 fs. Both an iterative genetic algorithm and single-step dispersion compensation based on frequency-resolved optical gating calibration of the mirror were used to compress pulses to within 10% of the transform limit. Frequency-resolved optical gating was used to characterize the pulses and to test the range of the deformable-mirror-based compressor.

  12. Mirrored Light Field Video Camera Adapter

    OpenAIRE

    Tsai, Dorian; Dansereau, Donald G.; Martin, Steve; Corke, Peter

    2016-01-01

    This paper proposes the design of a custom mirror-based light field camera adapter that is cheap, simple in construction, and accessible. Mirrors of different shape and orientation reflect the scene into an upwards-facing camera to create an array of virtual cameras with overlapping field of view at specified depths, and deliver video frame rate light fields. We describe the design, construction, decoding and calibration processes of our mirror-based light field camera adapter in preparation ...

  13. MIRROR THERAPY: A REVIEW OF EVIDENCES

    OpenAIRE

    Aishath Najiha; Jagatheesan Alagesan; Vandana J Rathod; Poongundran Paranthaman

    2015-01-01

    The aim of this review was to identify and summarize the existing evidences on mirror box therapy for the management of various musculoskeletal conditions. A systemic literature search was performed to identify studies concerning mirror therapy. The included journal articles were reviewed and assessed for its significance. Fifty one studies were identified and reviewed. Five different patient categories were studied: 24 studies focussed on mirror therapy after stroke, thirteen studies focusse...

  14. ELID Mirror Grinding Technology——Development of Metal Bonded Grinding Wheel%ELID镜面磨削技术——金属结合剂砂轮的研制

    Institute of Scientific and Technical Information of China (English)

    关佳亮; 郭东明; 周曙光; 袁哲俊

    2001-01-01

    As the result of the study on the effects of copper powder and other relative metal additives used for ELID grinding wheel manufacturing, a new kind of grinding wheel is presented for ELID grinding and experimental results show that such a grinding wheel has its great advantage and can be used for production pur pose.%采用铜粉、还原铁粉、铸铁粉并辅以改善铁粉和铸铁粉末冶金性能的金属添加剂作配方,烧制出适合现有生产条件的ELID磨削用砂轮磨块。性能检验表明该配方满足了ELID磨削要求。

  15. Single Crystal Silicon Mirrors for Spaceflight Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Develop a well understood process for manufacturing visible quality SCSi mirrors. Areas of research include stress relief, figure, finish, and light weighting...

  16. Mirror movements in progressive hemifacial atrophy

    Science.gov (United States)

    Verma, Rajesh; Dixit, Puneet Kumar; Lalla, Rakesh; Singh, Babita

    2015-01-01

    Mirror movements are simultaneous, involuntary, identical movements occurring during contralateral voluntary movements. These movements are considered as soft neurologic signs seen uncommonly in clinical practice. The mirror movements are described in various neurological disorders which include parkinsonism, cranio veretebral junction anamolies, and hemiplegic cerebral palsy. These movements are intriguing and can pose significant disability. However, no such observation regarding mirror movements in progressive hemifacial atrophy have been reported previously. We are reporting a teenage girl suffering from progressive hemifacial atrophy and epilepsy with demonstrable mirror movements in hand. PMID:26019431

  17. Analytic solution for a quartic electron mirror

    Energy Technology Data Exchange (ETDEWEB)

    Straton, Jack C., E-mail: straton@pdx.edu

    2015-01-15

    A converging electron mirror can be used to compensate for spherical and chromatic aberrations in an electron microscope. This paper presents an analytical solution to a diode (two-electrode) electrostatic mirror including the next term beyond the known hyperbolic shape. The latter is a solution of the Laplace equation to second order in the variables perpendicular to and along the mirror's radius (z{sup 2}−r{sup 2}/2) to which we add a quartic term (kλz{sup 4}). The analytical solution is found in terms of Jacobi cosine-amplitude functions. We find that a mirror less concave than the hyperbolic profile is more sensitive to changes in mirror voltages and the contrary holds for the mirror more concave than the hyperbolic profile. - Highlights: • We find the analytical solution for electron mirrors whose curvature has z4 dependence added to the usual z{sup 2} – r{sup 2}/2 terms. • The resulting Jacobi cosine-amplitude function reduces to the well-known cosh solution in the limit where the new term is 0. • This quartic term gives a mirror designer additional flexibility for eliminating spherical and chromatic aberrations. • The possibility of using these analytical results to approximately model spherical tetrode mirrors close to axis is noted.

  18. Mirror movements in progressive hemifacial atrophy

    Directory of Open Access Journals (Sweden)

    Rajesh Verma

    2015-01-01

    Full Text Available Mirror movements are simultaneous, involuntary, identical movements occurring during contralateral voluntary movements. These movements are considered as soft neurologic signs seen uncommonly in clinical practice. The mirror movements are described in various neurological disorders which include parkinsonism, cranio veretebral junction anamolies, and hemiplegic cerebral palsy. These movements are intriguing and can pose significant disability. However, no such observation regarding mirror movements in progressive hemifacial atrophy have been reported previously. We are reporting a teenage girl suffering from progressive hemifacial atrophy and epilepsy with demonstrable mirror movements in hand.

  19. Double curvature mirrors for linear concentrators

    Science.gov (United States)

    Lance, Tamir; Ackler, Harold; Finot, Marc

    2012-10-01

    Skyline Solar's medium concentration photovoltaic system uses quasi-parabolic mirrors and one axis tracking. Improvements in levelized cost of energy can be achieved by effective management of non-uniformity of the flux line on the panels. To reduce non uniformity of the flux line due to mirror to mirror gaps, Skyline developed a dual curvature mirror that stretches the flux line along the panel. Extensive modeling and experiments have been conducted to analyze the impact of this new design and to optimize the design.

  20. Effect of silicon carbide ceramic coating process on the mirror surface quality

    Science.gov (United States)

    Wang, Peipei; Wang, Li; Wang, Gang; Bai, Yunli; Wang, Peng; Xiao, Zhenghang

    2016-10-01

    Silicon carbide, as a new reflector material, its excellent physical and chemical properties has been widely recognized by the industry. In order to make SiC mirror better used in space optical system, we used digital coating equipment during its coating process. By using ion-assisted electron evaporation method, we got a complete metal reflective film system on the surface of finely polished silicon carbide mirror. After automated coating process, by adjusting the coating parameters during the process, the surface roughness of silicon carbide improved from 7.8 nm to 5.1 nm, and the average optical reflectance of the surface reached 95% from visible to near-infrared. The metal reflective film system kept well after annealing and firmness test. As a result, the work of this paper will provide an important reference for high-precision coating process on large diameter SiC mirror.

  1. The uncanny mirror: a re-framing of mirror self-experience.

    Science.gov (United States)

    Rochat, Philippe; Zahavi, Dan

    2011-06-01

    Mirror self-experience is re-casted away from the cognitivist interpretation that has dominated discussions on the issue since the establishment of the mirror mark test. Ideas formulated by Merleau-Ponty on mirror self-experience point to the profoundly unsettling encounter with one's specular double. These ideas, together with developmental evidence are re-visited to provide a new, psychologically and phenomenologically more valid account of mirror self-experience: an experience associated with deep wariness.

  2. One mirror beam steering: determination of steering mirror parameters from image pointing direction

    Science.gov (United States)

    Andersen, Torben B.; Granger, Zachary A.

    2016-09-01

    Mathematical models are used to establish the exact path of a beam reflected by a plane mirror in terms of the mirror geometry descriptors. In particular, the mirror geometry descriptors (tilt angles) are determined as functions of the beam path in image space. This is also useful for determining scan patterns when the mirror is used as a scanning device. These formulations are readily adaptable to commercially available ray tracing programs.

  3. Neurodegeneration and mirror image agnosia

    Directory of Open Access Journals (Sweden)

    Sadanandavalli Retnaswami Chandra

    2014-01-01

    Full Text Available Background: Normal Percept with abnormal meaning (Agnosias has been described from nineteenth century onwards. Later literature became abundant with information on the spectrum of Prosopagnosias. However, selective difficulty in identifying reflected self images with relatively better cognitive functions leads to problems in differentiating it from non-organic psychosis. Aim: In the present study, we investigated patients with dementia who showed difficulty in identifying reflected self images while they were being tested for problems in gnosis with reference to identification of reflected objects, animals, relatives, and themselves and correlate with neuropsychological and radiological parameters. Patients and Methods: Five such patients were identified and tested with a 45 cm × 45 cm mirror kept at 30-cm distance straight ahead of them. Results: Mirror image agnosia is seen in patients with moderate stage posterior dementias who showed neuropsychological and radiological evidence of right parietal dysfunction. Conclusion: Interpretation of reflected self images perception in real time probably involves distinct data-linking circuits in the right parietal lobe, which may get disrupted early in the course of the disease.

  4. FAME: freeform active mirror experiment

    Science.gov (United States)

    Aitink-Kroes, Gabby; Agócs, Tibor; Miller, Chris; Black, Martin; Farkas, Szigfrid; Lemared, Sabri; Bettonvil, Felix; Montgomery, David; Marcos, Michel; Jaskó, Attila; van Duffelen, Farian; Challita, Zalpha; Fok, Sandy; Kiaeerad, Fatemeh; Hugot, Emmanuel; Schnetler, Hermine; Venema, Lars

    2016-07-01

    FAME is a four-year project and part of the OPTICON/FP7 program that is aimed at providing a breakthrough component for future compact, wide field, high resolution imagers or spectrographs, based on both Freeform technology, and the flexibility and versatility of active systems. Due to the opening of a new parameter space in optical design, Freeform Optics are a revolution in imaging systems for a broad range of applications from high tech cameras to astronomy, via earth observation systems, drones and defense. Freeform mirrors are defined by a non-rotational symmetry of the surface shape, and the fact that the surface shape cannot be simply described by conicoids extensions, or off-axis conicoids. An extreme freeform surface is a significantly challenging optical surface, especially for UV/VIS/NIR diffraction limited instruments. The aim of the FAME effort is to use an extreme freeform mirror with standard optics in order to propose an integrated system solution for use in future instruments. The work done so far concentrated on identification of compact, fast, widefield optical designs working in the visible, with diffraction limited performance; optimization of the number of required actuators and their layout; the design of an active array to manipulate the face sheet, as well as the actuator design. In this paper we present the status of the demonstrator development, with focus on the different building blocks: an extreme freeform thin face sheet, the active array, a highly controllable thermal actuator array, and the metrology and control system.

  5. Explaining mirror-touch synesthesia.

    Science.gov (United States)

    Ward, Jamie; Banissy, Michael J

    2015-01-01

    Mirror-touch synesthesia (MTS) is the conscious experience of tactile sensations induced by seeing someone else touched. This paper considers two different, although not mutually exclusive, theoretical explanations and, in the final section, considers the relation between MTS and other forms of synesthesia and also other kinds of vicarious perception (e.g., contagious yawning). The Threshold Theory explains MTS in terms of hyper-activity within a mirror system for touch and/or pain. This offers a good account for some of the evidence (e.g., from fMRI) but fails to explain the whole pattern (e.g., structural brain differences outside of this system; performance on some tests of social cognition). The Self-Other Theory explains MTS in terms of disturbances in the ability to distinguish the self from others. This can be construed in terms of over-extension of the bodily self in to others, or as difficulties in the control of body-based self-other representations. In this account, MTS is a symptom of a broader cognitive profile. We suggest this meets the criteria for synesthesia, despite the proximal causal mechanisms remaining largely unknown, and that the tendency to localize vicarious sensory experiences distinguishes it from other kinds of seemingly related phenomena (e.g., non-localized affective responses to observing pain).

  6. Neurodegeneration and Mirror Image Agnosia

    Science.gov (United States)

    Chandra, Sadanandavalli Retnaswami; Issac, Thomas Gregor

    2014-01-01

    Background: Normal Percept with abnormal meaning (Agnosias) has been described from nineteenth century onwards. Later literature became abundant with information on the spectrum of Prosopagnosias. However, selective difficulty in identifying reflected self images with relatively better cognitive functions leads to problems in differentiating it from non-organic psychosis. Aim: In the present study, we investigated patients with dementia who showed difficulty in identifying reflected self images while they were being tested for problems in gnosis with reference to identification of reflected objects, animals, relatives, and themselves and correlate with neuropsychological and radiological parameters. Patients and Methods: Five such patients were identified and tested with a 45 cm × 45 cm mirror kept at 30-cm distance straight ahead of them. Results: Mirror image agnosia is seen in patients with moderate stage posterior dementias who showed neuropsychological and radiological evidence of right parietal dysfunction. Conclusion: Interpretation of reflected self images perception in real time probably involves distinct data-linking circuits in the right parietal lobe, which may get disrupted early in the course of the disease. PMID:25317393

  7. Relativistic Tennis Using Flying Mirror

    Science.gov (United States)

    Pirozhkov, A. S.; Kando, M.; Esirkepov, T. Zh.; Ma, J.; Fukuda, Y.; Chen, L.-M.; Daito, I.; Ogura, K.; Homma, T.; Hayashi, Y.; Kotaki, H.; Sagisaka, A.; Mori, M.; Koga, J. K.; Kawachi, T.; Daido, H.; Bulanov, S. V.; Kimura, T.; Kato, Y.; Tajima, T.

    2008-06-01

    Upon reflection from a relativistic mirror, the electromagnetic pulse frequency is upshifted and the duration is shortened by the factor proportional to the relativistic gamma-factor squared due to the double Doppler effect. We present the results of the proof-of-principle experiment for frequency upshifting of the laser pulse reflected from the relativistic "flying mirror", which is a wake wave near the breaking threshold created by a strong driver pulse propagating in underdense plasma. Experimentally, the wake wave is created by a 2 TW, 76 fs Ti:S laser pulse from the JLITE-X laser system in helium plasma with the electron density of ≈4-6×1019 cm-3. The reflected signal is observed with a grazing-incidence spectrograph in 24 shots. The wavelength of the reflected radiation ranges from 7 to 14 nm, the corresponding frequency upshifting factors are ˜55-115, and the gamma-factors are y = 4-6. The reflected signal contains at least 3×107 photons/sr. This effect can be used to generate coherent high-frequency ultrashort pulses that inherit temporal shape and polarization from the original (low-frequency) ones. Apart from this, the reflected radiation contains important information about the wake wave itself, e.g. location, size, phase velocity, etc.

  8. Mirror particles and mirror matter: 50 years of speculations and searches

    CERN Document Server

    Okun, Lev Borisovich

    2006-01-01

    This text has been prepared for the talk at the ``ITEP Meeting on the future of heavy flavor physics'', Moscow, ITEP, July 24-25, 2006 (http://www.itep.ru/eng/bellemeeting). It describes emergence and evolution of concept of ``mirror particles'' and ``mirror matter'' and presents a concise guide to the ``mirror-land''.

  9. High reflectivity mirrors and method for making same

    Energy Technology Data Exchange (ETDEWEB)

    Heikman, Sten; Jacob-Mitos, Matthew; Li, Ting; Ibbetson, James

    2016-06-07

    A composite high reflectivity mirror (CHRM) with at least one relatively smooth interior surface interface. The CHRM includes a composite portion, for example dielectric and metal layers, on a base element. At least one of the internal surfaces is polished to achieve a smooth interface. The polish can be performed on the surface of the base element, on various layers of the composite portion, or both. The resulting smooth interface(s) reflect more of the incident light in an intended direction. The CHRMs may be integrated into light emitting diode (LED) devices to increase optical output efficiency

  10. 采用ALD方法制备TiO2/Al2O3布拉格反射镜并配合金属反射镜来增强背镀结构的反射效率%High Reflectance of Backside Reflector with a Hybrid Metallic Mirror and ALD-TiO2/Al2O3 DBR

    Institute of Scientific and Technical Information of China (English)

    陈洪钧; 郭浩; 张雄; 崔一平

    2013-01-01

    首次采用原子层沉积法制备TiO2/Al2O3布拉格反射镜并配合金属反射镜来制备了高反射率的背反射镜.制备的多层布拉格反射镜加Al镜和多层布拉格反射镜加Ag镜有很好的平整度和厚度的精确性,并且反射率高于96%.此外,TiO2/Al2O3布拉格反射镜和Al与蓝宝石衬底都有良好的粘合性,这样可以节省制备步骤并且可以得到高质量的背反射镜.利用原子层沉积技术和TiO2/Al2O3布拉格反射镜,我们得到了高反射率,角度依赖性小,更加稳定以及均一性更好的背反射镜,可以满足高亮度LED的需求.%High reflectivity backside reflectors combining TiO2/Al2O3 distributed Bragg reflector (DBR)by atomic layer deposition (ALD)with metallic mirror have been demonstrated for the first time.Multi-pair-DBRs/Al and multi-pair-DBRs/Ag stacks with excellent uniformity and thickness accuracy have exhibited high reflectivities above 96%.Besides,TiO2/Al2O3 DBR has good adhesion with both sapphire substrate and Al mirror,we simplified the fabrication process and achieved more stabilized backside reflector.By combining ALD deposition with TiO2/Al2O3DBR,high reflectivity,less angle dependency,more stabilized and excellent film uniformity backside reflector is achieved to meet the requirements of high brightness light-emitting diodes(LEDs).

  11. White Light Pump-Probe Photothermal Mirror Spectrophotometer

    Science.gov (United States)

    Hlaing, May; Marcano, Aristides

    2016-05-01

    We develop a new kind of spectrophotometer based on the photothermal mirror effect. The absorption of a focused tunable pump light by first atomic layers of the sample's surface generates a nanometric surface distortion or bump of thermal origin. A probe beam of light of fixed wavelength and with spot dimensions much larger than the pump beam's spot is used to test this thermal distortion. Changes in the wave-front of the reflected probe beam yields changes of the diffraction pattern of the reflected beam at the far field which can be used to produce a signal proportional to the amount of released heat. Tuning of the wavelength of the pump field generates a photothermal mirror spectrum. As tunable pump source we use the light from a Xenon arc-lamp filtered using a series of interference filter. This way we generate tunable pump light in the spectral region of 370-730 nm with a HWHM of 5 nm and power density of the order of tens of microwatts per nanometer. We obtain photothermal mirror spectra of metallic surfaces and other non-transparent samples. We show that these spectra are fundamentally different from the usual reflectance spectra which measure the percentage of the total of the total energy reflected by the surface.

  12. Manufacturing Precise, Lightweight Paraboloidal Mirrors

    Science.gov (United States)

    Hermann, Frederick Thomas

    2006-01-01

    A process for fabricating a precise, diffraction- limited, ultra-lightweight, composite- material (matrix/fiber) paraboloidal telescope mirror has been devised. Unlike the traditional process of fabrication of heavier glass-based mirrors, this process involves a minimum of manual steps and subjective judgment. Instead, this process involves objectively controllable, repeatable steps; hence, this process is better suited for mass production. Other processes that have been investigated for fabrication of precise composite-material lightweight mirrors have resulted in print-through of fiber patterns onto reflecting surfaces, and have not provided adequate structural support for maintenance of stable, diffraction-limited surface figures. In contrast, this process does not result in print-through of the fiber pattern onto the reflecting surface and does provide a lightweight, rigid structure capable of maintaining a diffraction-limited surface figure in the face of changing temperature, humidity, and air pressure. The process consists mainly of the following steps: 1. A precise glass mandrel is fabricated by conventional optical grinding and polishing. 2. The mandrel is coated with a release agent and covered with layers of a carbon- fiber composite material. 3. The outer surface of the outer layer of the carbon-fiber composite material is coated with a surfactant chosen to provide for the proper flow of an epoxy resin to be applied subsequently. 4. The mandrel as thus covered is mounted on a temperature-controlled spin table. 5. The table is heated to a suitable temperature and spun at a suitable speed as the epoxy resin is poured onto the coated carbon-fiber composite material. 6. The surface figure of the optic is monitored and adjusted by use of traditional Ronchi, Focault, and interferometric optical measurement techniques while the speed of rotation and the temperature are adjusted to obtain the desired figure. The proper selection of surfactant, speed or rotation

  13. LHCb ring imaging Cherenkov detector mirrors

    CERN Multimedia

    Maximilien Brice

    2005-01-01

    In a large dark room, men in white move around an immense structure some 7 m high, 10 m wide and nearly 2.5 m deep. Apparently effortlessly, they are installing the two large high-precision spherical mirrors. These mirrors will focus Cherenkov light, created by the charged particles that will traverse this detector, onto the photon detectors.

  14. Evolution of the tandem mirror reactor concept

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, G.A.; Logan, B.G.

    1982-03-09

    We discuss the evolution of the tandem mirror reactor concept from the original conceptual reactor design (1977) through the first application of the thermal barrier concept to a reactor design (1979) to the beginning of the Mirror Advanced Reactor Study (1982).

  15. LED structure with enhanced mirror reflectivity

    Science.gov (United States)

    Bergmann, Michael; Donofrio, Matthew; Heikman, Sten; Schneider, Kevin S; Haberern, Kevin W; Edmond, John A

    2014-04-01

    Embodiments of the present invention are generally related to LED chips having improved overall emission by reducing the light-absorbing effects of barrier layers adjacent mirror contacts. In one embodiment, a LED chip comprises one or more LEDs, with each LED having an active region, a first contact under the active region having a highly reflective mirror, and a barrier layer adjacent the mirror. The barrier layer is smaller than the mirror such that it does not extend beyond the periphery of the mirror. In another possible embodiment, an insulator is further provided, with the insulator adjacent the barrier layer and adjacent portions of the mirror not contacted by the active region or by the barrier layer. In yet another embodiment, a second contact is provided on the active region. In a further embodiment, the barrier layer is smaller than the mirror such that the periphery of the mirror is at least 40% free of the barrier layer, and the second contact is below the first contact and accessible from the bottom of the chip.

  16. Segmented mirror control system hardware for CELT

    Science.gov (United States)

    Mast, Terry S.; Nelson, Jerry E.

    2000-07-01

    The primary mirror of the proposed California Extremely Large Telescope is a 30-meter diameter mosaic of hexagonal segments. The primary mirror active control will be achieved using four systems: sensors, actuators, processor, and alignment camera. We describe here the basic requirements of sensors and actuators, sketch a sensor design, and indicate interesting actuator alternatives.

  17. The Mirror Neuron System and Action Recognition

    Science.gov (United States)

    Buccino, Giovanni; Binkofski, Ferdinand; Riggio, Lucia

    2004-01-01

    Mirror neurons, first described in the rostral part of monkey ventral premotor cortex (area F5), discharge both when the animal performs a goal-directed hand action and when it observes another individual performing the same or a similar action. More recently, in the same area mirror neurons responding to the observation of mouth actions have been…

  18. Where do mirror neurons come from?

    Science.gov (United States)

    Heyes, Cecilia

    2010-03-01

    Debates about the evolution of the 'mirror neuron system' imply that it is an adaptation for action understanding. Alternatively, mirror neurons may be a byproduct of associative learning. Here I argue that the adaptation and associative hypotheses both offer plausible accounts of the origin of mirror neurons, but the associative hypothesis has three advantages. First, it provides a straightforward, testable explanation for the differences between monkeys and humans that have led some researchers to question the existence of a mirror neuron system. Second, it is consistent with emerging evidence that mirror neurons contribute to a range of social cognitive functions, but do not play a dominant, specialised role in action understanding. Finally, the associative hypothesis is supported by recent data showing that, even in adulthood, the mirror neuron system can be transformed by sensorimotor learning. The associative account implies that mirror neurons come from sensorimotor experience, and that much of this experience is obtained through interaction with others. Therefore, if the associative account is correct, the mirror neuron system is a product, as well as a process, of social interaction. (c) 2009 Elsevier Ltd. All rights reserved.

  19. Unbroken Mirror Neurons in Autism Spectrum Disorders

    Science.gov (United States)

    Fan, Yang-Teng; Decety, Jean; Yang, Chia-Yen; Liu, Ji-Lin; Cheng, Yawei

    2010-01-01

    Background: The "broken mirror" theory of autism, which proposes that a dysfunction of the human mirror neuron system (MNS) is responsible for the core social and cognitive deficits in individuals with autism spectrum disorders (ASD), has received considerable attention despite weak empirical evidence. Methods: In this electroencephalographic…

  20. Do mirror neurons subserve action understanding?

    Science.gov (United States)

    Hickok, Gregory

    2013-04-12

    Mirror neurons were once widely believed to support action understanding via motor simulation of the observed actions. Recent evidence regarding the functional properties of mirror neurons in monkeys as well as much neuropsychological evidence in humans has shown that this is not the case. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

  1. Mirror matter and primordial black holes

    OpenAIRE

    Bell, Nicole F.; Volkas, Raymond R.

    1998-01-01

    A consequence of the evaporation of primordial black holes in the early universe may be the generation of mirror matter. This would have implications with regard to dark matter, and the number of light particle species in equilibrium at the time of big bang nucleosynthesis. The possibilities for the production of mirror matter by this mechanism are explored.

  2. Cortical mechanisms of mirror therapy after stroke.

    Science.gov (United States)

    Rossiter, Holly E; Borrelli, Mimi R; Borchert, Robin J; Bradbury, David; Ward, Nick S

    2015-06-01

    Mirror therapy is a new form of stroke rehabilitation that uses the mirror reflection of the unaffected hand in place of the affected hand to augment movement training. The mechanism of mirror therapy is not known but is thought to involve changes in cerebral organization. We used magnetoencephalography (MEG) to measure changes in cortical activity during mirror training after stroke. In particular, we examined movement-related changes in the power of cortical oscillations in the beta (15-30 Hz) frequency range, known to be involved in movement. Ten stroke patients with upper limb paresis and 13 healthy controls were recorded using MEG while performing bimanual hand movements in 2 different conditions. In one, subjects looked directly at their affected hand (or dominant hand in controls), and in the other, they looked at a mirror reflection of their unaffected hand in place of their affected hand. The movement-related beta desynchronization was calculated in both primary motor cortices. Movement-related beta desynchronization was symmetrical during bilateral movement and unaltered by the mirror condition in controls. In the patients, movement-related beta desynchronization was generally smaller than in controls, but greater in contralesional compared to ipsilesional motor cortex. This initial asymmetry in movement-related beta desynchronization between hemispheres was made more symmetrical by the presence of the mirror. Mirror therapy could potentially aid stroke rehabilitation by normalizing an asymmetrical pattern of movement-related beta desynchronization in primary motor cortices during bilateral movement. © The Author(s) 2014.

  3. Unbroken Mirror Neurons in Autism Spectrum Disorders

    Science.gov (United States)

    Fan, Yang-Teng; Decety, Jean; Yang, Chia-Yen; Liu, Ji-Lin; Cheng, Yawei

    2010-01-01

    Background: The "broken mirror" theory of autism, which proposes that a dysfunction of the human mirror neuron system (MNS) is responsible for the core social and cognitive deficits in individuals with autism spectrum disorders (ASD), has received considerable attention despite weak empirical evidence. Methods: In this electroencephalographic…

  4. The Mirror Neuron System and Action Recognition

    Science.gov (United States)

    Buccino, Giovanni; Binkofski, Ferdinand; Riggio, Lucia

    2004-01-01

    Mirror neurons, first described in the rostral part of monkey ventral premotor cortex (area F5), discharge both when the animal performs a goal-directed hand action and when it observes another individual performing the same or a similar action. More recently, in the same area mirror neurons responding to the observation of mouth actions have been…

  5. Affective multimodal mirror: sensing and eliciting laughter

    NARCIS (Netherlands)

    Melder, W.A.; Truong, K.P.; Uyl, M. den; Leeuwen, D.A. van; Neerincx, M.A.; Loos, L.R.; Stock Plum, B.

    2007-01-01

    In this paper, we present a multimodal affective mirror that senses and elicits laughter. Currently, the mirror contains a vocal and a facial affect-sensing module, a component that fuses the output of these two modules to achieve a user-state assessment, a user state transition model, and a compone

  6. Optical switching properties of Pd-Ni thin-film top-capped switchable mirrors

    Science.gov (United States)

    Zhang, Xiao-Li; Bao, Shan-Hu; Xin, Yun-Chuan; Cao, Xun; Jin, Ping

    2015-09-01

    Switchable mirrors based on magnesium-nickel alloy thin films capped with catalytic Pd-Ni alloy thin films were prepared by a DC magnetron sputtering method. Their composition, structure and surface morphology were studied by XPS, XRD and AFM. Herein, the optical switching properties and durability of the switchable mirrors were investigated by varying the Ni content in the Pd-Ni alloys. Comparing pure Pd catalyst with Pd-Ni top-capped switchable mirrors, the latter show better hydrogenation and dehydrogenation kinetics, and the speed of hydrogen desorption is obviously improved with increasing Ni content in the Pd-Ni alloy. The Pd-Ni capped switchable mirrors also have better optical switching durability. The catalytic Pd layer with the addition of Ni does not influence the transmittance (hydride state) and reflectance (metallic state) of the switchable mirrors. In addition, replacing Pd with Pd-Ni alloy decreases the cost of the switchable mirrors: employing nickel in the alloy Pd89.2Ni10.8 can save about 11% use of Pd. Therefore, the Pd-Ni alloy can provide a cheaper catalytic thin film, and it is expected to have applications in energy-saving windows, hydrogen sensors and hydrogen storage materials.

  7. Mirror neurons through the lens of epigenetics.

    Science.gov (United States)

    Ferrari, Pier F; Tramacere, Antonella; Simpson, Elizabeth A; Iriki, Atsushi

    2013-09-01

    The consensus view in mirror neuron research is that mirror neurons comprise a uniform, stable execution-observation matching system. In this opinion article, we argue that, in light of recent evidence, this is at best an incomplete and oversimplified view of mirror neurons, where activity is actually variable and more plastic than previously theorized. We propose an epigenetic account for understanding developmental changes in sensorimotor systems, including variations in mirror neuron activity. Although associative and genetic accounts fail to consider the complexity of genetic and nongenetic interactions, we propose a new evolutionary developmental biology (evo-devo) perspective, which predicts that environmental differences early in development should produce variations in mirror neuron response patterns, tuning them to the social environment. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. Mirror neurons and their clinical relevance.

    Science.gov (United States)

    Rizzolatti, Giacomo; Fabbri-Destro, Maddalena; Cattaneo, Luigi

    2009-01-01

    One of the most exciting events in neurosciences over the past few years has been the discovery of a mechanism that unifies action perception and action execution. The essence of this 'mirror' mechanism is as follows: whenever individuals observe an action being done by someone else, a set of neurons that code for that action is activated in the observers' motor system. Since the observers are aware of the outcome of their motor acts, they also understand what the other individual is doing without the need for intermediate cognitive mediation. In this Review, after discussing the most pertinent data concerning the mirror mechanism, we examine the clinical relevance of this mechanism. We first discuss the relationship between mirror mechanism impairment and some core symptoms of autism. We then outline the theoretical principles of neurorehabilitation strategies based on the mirror mechanism. We conclude by examining the relationship between the mirror mechanism and some features of the environmental dependency syndromes.

  9. Cryostable lightweight frit bonded silicon mirror

    Science.gov (United States)

    Anthony, F.; McCarter, D.; Tangedahl, M.; Content, D.

    The excellent polishability, low density and relatively high stiffness of silicon make it an attractive candidate for optical applications that require superior performance. Assembly of silicon details by means of glass frit bonding permits significant light weighting thus enhancing the benefit of silicon mirrors. To demonstrate the performance potential, a small lightweight glass frit bonded silicon mirror was fabricated and tested for cryoability. The test mirror was 12.5cm in diameter with a 60cm spherical radius and a maximum thickness, at the perimeter, of 2.5cm. A machined silicon core was used to stiffen the two face sheets of the silicon sandwich. These three elements were assembled, by glass frit bonding, to form the substrate that was polished. The experimental evaluation in a liquid nitrogen cryostat, demonstrated cryostability performance significantly better than required by the mirror specification. Key WordsCryostable, Lightweight, Silicon, Frit Bond, Spherical, Mirror

  10. DAMA annual modulation and mirror Dark Matter

    Energy Technology Data Exchange (ETDEWEB)

    Cerulli, R.; Cappella, F. [INFN, Laboratori Nazionali del Gran Sasso, Assergi, AQ (Italy); Villar, P. [Universidad de Zaragoza, Laboratorio de Fisica Nuclear y Astroparticulas, Saragossa (Spain); Laboratorio Subterraneo de Canfranc, Canfranc Estacion, Huesca (Spain); Bernabei, R.; Belli, P. [Universita di Roma ' ' Tor Vergata' ' , Dipartimento di Fisica, Rome (Italy); INFN ' ' Tor Vergata' ' , Rome (Italy); Incicchitti, A. [Universita di Roma ' ' La Sapienza' ' , Dipartimento di Fisica, Rome (Italy); INFN, Rome (Italy); Addazi, A.; Berezhiani, Z. [INFN, Laboratori Nazionali del Gran Sasso, Assergi, AQ (Italy); Universita di L' Aquila, Dipartimento di Scienze Fisiche e Chimiche, Coppito, AQ (Italy)

    2017-02-15

    The DAMA experiment using ultra low background NaI(Tl) crystal scintillators has measured an annual modulation effect in the keV region which satisfies all the peculiarities of an effect induced by Dark Matter particles. In this paper we analyze this annual modulation effect in terms of mirror Dark Matter, an exact duplicate of ordinary matter from parallel hidden sector, which chemical composition is dominated by mirror helium while it can also contain significant fractions of heavier elements as Carbon and Oxygen. Dark mirror atoms are considered to interact with the target nuclei in the detector via Rutherford-like scattering induced by kinetic mixing between mirror and ordinary photons, both being massless. In the present analysis we consider various possible scenarios for the mirror matter chemical composition. For all the scenarios, the relevant ranges for the kinetic mixing parameter have been obtained taking also into account various existing uncertainties in nuclear and particle physics quantities. (orig.)

  11. DAMA annual modulation and mirror Dark Matter

    Science.gov (United States)

    Cerulli, R.; Villar, P.; Cappella, F.; Bernabei, R.; Belli, P.; Incicchitti, A.; Addazi, A.; Berezhiani, Z.

    2017-02-01

    The DAMA experiment using ultra low background NaI(Tl) crystal scintillators has measured an annual modulation effect in the keV region which satisfies all the peculiarities of an effect induced by Dark Matter particles. In this paper we analyze this annual modulation effect in terms of mirror Dark Matter, an exact duplicate of ordinary matter from parallel hidden sector, which chemical composition is dominated by mirror helium while it can also contain significant fractions of heavier elements as Carbon and Oxygen. Dark mirror atoms are considered to interact with the target nuclei in the detector via Rutherford-like scattering induced by kinetic mixing between mirror and ordinary photons, both being massless. In the present analysis we consider various possible scenarios for the mirror matter chemical composition. For all the scenarios, the relevant ranges for the kinetic mixing parameter have been obtained taking also into account various existing uncertainties in nuclear and particle physics quantities.

  12. [Motion control of moving mirror based on fixed-mirror adjustment in FTIR spectrometer].

    Science.gov (United States)

    Li, Zhong-bing; Xu, Xian-ze; Le, Yi; Xu, Feng-qiu; Li, Jun-wei

    2012-08-01

    The performance of the uniform motion of the moving mirror, which is the only constant motion part in FTIR spectrometer, and the performance of the alignment of the fixed mirror play a key role in FTIR spectrometer, and affect the interference effect and the quality of the spectrogram and may restrict the precision and resolution of the instrument directly. The present article focuses on the research on the uniform motion of the moving mirror and the alignment of the fixed mirror. In order to improve the FTIR spectrometer, the maglev support system was designed for the moving mirror and the phase detection technology was adopted to adjust the tilt angle between the moving mirror and the fixed mirror. This paper also introduces an improved fuzzy PID control algorithm to get the accurate speed of the moving mirror and realize the control strategy from both hardware design and algorithm. The results show that the development of the moving mirror motion control system gets sufficient accuracy and real-time, which can ensure the uniform motion of the moving mirror and the alignment of the fixed mirror.

  13. Toward a large lightweight mirror for AO: development of a 1m Ni coated CFRP mirror

    Science.gov (United States)

    Thompson, S. J.; Doel, A. P.; Brooks, D.; Strangwood, M.

    2008-07-01

    We present our recent developments towards the construction of a large, thin, single-piece mirror for adaptive optics (AO). Our current research program aims to have completed fabrication and testing of a 1m diameter, nickel coated carbon-fibre reinforced cyanate ester resin mirror by the last quarter of 2009. This composite mirror material is being developed to provide a lightweight and robust alternative to thin glass shell mirrors, with the challenge of future large deformable mirrors such as the 2.5m M4 on the E-ELT in mind. A detailed analysis of the material properties of test mirror samples is being performed at the University of Birmingham (UK), the first results of which are discussed and presented here. We discuss the project progress achieved so far, including fabrication of the 1m flat moulds for the replication process, manufacturing and testing methods for 20 cm diameter sample mirrors and system simulations.

  14. Mirror neurons: from origin to function.

    Science.gov (United States)

    Cook, Richard; Bird, Geoffrey; Catmur, Caroline; Press, Clare; Heyes, Cecilia

    2014-04-01

    This article argues that mirror neurons originate in sensorimotor associative learning and therefore a new approach is needed to investigate their functions. Mirror neurons were discovered about 20 years ago in the monkey brain, and there is now evidence that they are also present in the human brain. The intriguing feature of many mirror neurons is that they fire not only when the animal is performing an action, such as grasping an object using a power grip, but also when the animal passively observes a similar action performed by another agent. It is widely believed that mirror neurons are a genetic adaptation for action understanding; that they were designed by evolution to fulfill a specific socio-cognitive function. In contrast, we argue that mirror neurons are forged by domain-general processes of associative learning in the course of individual development, and, although they may have psychological functions, they do not necessarily have a specific evolutionary purpose or adaptive function. The evidence supporting this view shows that (1) mirror neurons do not consistently encode action "goals"; (2) the contingency- and context-sensitive nature of associative learning explains the full range of mirror neuron properties; (3) human infants receive enough sensorimotor experience to support associative learning of mirror neurons ("wealth of the stimulus"); and (4) mirror neurons can be changed in radical ways by sensorimotor training. The associative account implies that reliable information about the function of mirror neurons can be obtained only by research based on developmental history, system-level theory, and careful experimentation.

  15. Archetypal-Imaging and Mirror-Gazing

    Directory of Open Access Journals (Sweden)

    Giovanni B. Caputo

    2013-12-01

    Full Text Available Mirrors have been studied by cognitive psychology in order to understand self-recognition, self-identity, and self-consciousness. Moreover, the relevance of mirrors in spirituality, magic and arts may also suggest that mirrors can be symbols of unconscious contents. Carl G. Jung investigated mirrors in relation to the unconscious, particularly in Psychology and Alchemy. However, the relationship between the conscious behavior in front of a mirror and the unconscious meaning of mirrors has not been clarified. Recently, empirical research found that gazing at one’s own face in the mirror for a few minutes, at a low illumination level, produces the perception of bodily dysmorphic illusions of strange-faces. Healthy observers usually describe huge distortions of their own faces, monstrous beings, prototypical faces, faces of relatives and deceased, and faces of animals. In the psychiatric population, some schizophrenics show a dramatic increase of strange-face illusions. They can also describe the perception of multiple-others that fill the mirror surface surrounding their strange-face. Schizophrenics are usually convinced that strange-face illusions are truly real and identify themselves with strange-face illusions, diversely from healthy individuals who never identify with them. On the contrary, most patients with major depression do not perceive strange-face illusions, or they perceive very faint changes of their immobile faces in the mirror, like death statues. Strange-face illusions may be the psychodynamic projection of the subject’s unconscious archetypal contents into the mirror image. Therefore, strange-face illusions might provide both an ecological setting and an experimental technique for “imaging of the unconscious”. Future researches have been proposed.

  16. Archetypal-imaging and mirror-gazing.

    Science.gov (United States)

    Caputo, Giovanni B

    2014-03-01

    Mirrors have been studied by cognitive psychology in order to understand self-recognition, self-identity, and self-consciousness. Moreover, the relevance of mirrors in spirituality, magic and arts may also suggest that mirrors can be symbols of unconscious contents. Carl G. Jung investigated mirrors in relation to the unconscious, particularly in Psychology and Alchemy. However, the relationship between the conscious behavior in front of a mirror and the unconscious meaning of mirrors has not been clarified. Recently, empirical research found that gazing at one's own face in the mirror for a few minutes, at a low illumination level, produces the perception of bodily dysmorphic illusions of strange-faces. Healthy observers usually describe huge distortions of their own faces, monstrous beings, prototypical faces, faces of relatives and deceased, and faces of animals. In the psychiatric population, some schizophrenics show a dramatic increase of strange-face illusions. They can also describe the perception of multiple-others that fill the mirror surface surrounding their strange-face. Schizophrenics are usually convinced that strange-face illusions are truly real and identify themselves with strange-face illusions, diversely from healthy individuals who never identify with them. On the contrary, most patients with major depression do not perceive strange-face illusions, or they perceive very faint changes of their immobile faces in the mirror, like death statues. Strange-face illusions may be the psychodynamic projection of the subject's unconscious archetypal contents into the mirror image. Therefore, strange-face illusions might provide both an ecological setting and an experimental technique for "imaging of the unconscious". Future researches have been proposed.

  17. Large thin adaptive x-ray mirrors

    Science.gov (United States)

    Doel, Peter; Atkins, Carolyn; Thompson, Samantha; Brooks, David; Yao, Jun; Feldman, Charlotte; Willingale, Richard; Button, Tim; Zhang, Dou; James, Ady

    2007-09-01

    This paper describes the progress made in a proof of concept study and recent results of a research program into large active x-ray mirrors that is part of the UK Smart X-ray Optics project. The ultimate aim is to apply the techniques of active/adaptive optics to the next generation of nested shell astronomical X-ray space telescopes. A variety of deformable mirror technologies are currently available, the most promising of which for active X-ray mirrors are probably unimorph and bimorph piezoelectric mirrors. In this type of mirror one or more sheets of piezoelectric material are bonded to or coated with a passive reflective layer. On the back or between the piezoceramic layer/layers are series of electrodes. Application of an electric field causes the piezoelectric material to undergo local deformation thus changing the mirror shape. Starting in 2005 a proof of concept active mirror research program has been undertaken. This work included modelling and development of actively controlled thin shell mirrors. Finite element models of piezo-electric actuated mirrors have been developed and verified against experimental test systems. This has included the modelling and test of piezo-electric hexagonal unimorph segments. Various actuator types and low shrinkage conductive bonding methods have been investigated and laboratory tests of the use of piezo-electric actuators to adjust the form of an XMM-Newton space telescope engineering model mirror shell have been conducted and show that movement of the optics at the required level is achievable. Promising technological approaches have been identified including moulded piezo-ceramics and piezo-electrics fibre bundles.

  18. Double arch mirror study. Part 3: Fabrication and test report

    Science.gov (United States)

    Vukobratovich, D.; Hillman, D.

    1983-01-01

    A method of mounting a cryogenically cooled, lightweight, double arch, glass mirror was developed for infrared, astronomical telescopes such as the Space Infrared Telescope Facility (SIRTF). A 50 cm, fused silica mirror which was previously fabricated was modified for use with a new mount configuration. This mount concept was developed. The modification of the mirror, the fabrication of the mirror mount, and the room temperature testing of the mounted mirror are reported. A design for a SIRTF class primary mirror is suggested.

  19. 软X射线多层膜设计中表面粗糙度对反射率的影响%Roughness effects on the reflectance in the design of a soft X-ray multi-layer mirror

    Institute of Scientific and Technical Information of China (English)

    胡家升; 宋利民

    2004-01-01

    给出了一种改进的软X射线波段的多层膜设计方法.在设计过程中,考虑了反射镜基底和各膜层之间的均方(RMS)粗糙度对反射率的影响;在Stearns提出的散射理论的基础上给出了粗糙界面的数学模型.文中以波长为λ=1.03 nm的软X射线为例进行设计,设计结果表明:要使波长为λ=1.03 nm的多层膜的反射率大于10%,反射镜基底的均方粗糙度不应超过0.6 nm.实验中选择几块表面粗糙度为0.5 nm(RMS)的熔石英平面镜作为基底来制作适用于该波长的、层对数超过70的多层膜.然后在的入射角下测量反射率,测得的值为10%,这与采用本设计方法得到的计算结果一致.该反射镜作为X射线谱仪的分光元件被应用于惯性约束聚变(ICF)的过程诊断中.%In the design of a multi-layer mirror at λ=1.03 nm in soft X-ray regin, a modified method is presented, in which the effects of root-mean-square (rms) roughness of the substrate and interfaces between these films on the reflectance are considered and discussed. Then, the mathematical model for rough interfaces is given based on the scattering theory presented by D. G. Stearns. The design result shows that the substrate roughness (rms) should be smaller than 0.6 nm in order to fabricate a multi-layer mirror whose reflectance is greater than 10%. A few super-polished fused quartz substrates with 0.5 nm (rms) roughness are chosen in coating experiments. The measured reflectance is about 10% at λ=1.03 nm,which is consistent with the result acquired by the modified design method. The multi-layer mirror has been applied in a X-ray spectrograph for diagnosis of inertial confinement fusion (ICF).

  20. UV-Shifted Durable Silver Coating for Astronomical Mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, N.L.; Wolfe, J.

    2000-06-01

    Silver has the highest reflectance of all of the metals, but it tarnishes in the presence of sulfides, chlorides, and oxides in the atmosphere. Also, the silver reflectance is very low at wavelengths below 400 nm making aluminum more desirable mirror coating for the UV region. They have found a way to prevent silver tarnishing by sandwiching the silver layer between two thin layers of NiCrN{sub x}, and to extend the metal's high reflectance down to 200 nm by depositing the (thin) Ag layer on top of Al. Thus, the uv is transmitted through the thin Ag layer below 400 nm wavelength, and is reflected from the Al layer underneath. This UV-shifted durable coating provides a valuable alternative to the aluminum coating for telescope mirror coatings where high throughput and durability are important considerations. The throughput for a telescope with, say, six reflections from silver coatings is (0.97){sup 6} = 83% compared to (0.92){sup 6} = 60% for aluminum coatings, or 28% less. The use of silver coatings allows more photons to be collected by primary mirror. Aluminum also has a reflectance dip at 850 nm caused by inter-band transitions which is eliminated by placing the thin Ag layer on top. This paper describes a non-tarnishing silver coating having high reflectance down into the UV region. The average specular reflectance is 70%-97% in the near-UV, 95%-99% in the visible region, and {ge} 99% in the infrared region covering the total wavelength range 200 nm to 10,000 nm. Figure 1 compares the reflectance of the UVHR-LLNL silver coating to bare silver and aluminum over-coated with magnesium fluoride over the wavelength range 300 nm to 2000 nm.

  1. Mirror neurons: functions, mechanisms and models.

    Science.gov (United States)

    Oztop, Erhan; Kawato, Mitsuo; Arbib, Michael A

    2013-04-12

    Mirror neurons for manipulation fire both when the animal manipulates an object in a specific way and when it sees another animal (or the experimenter) perform an action that is more or less similar. Such neurons were originally found in macaque monkeys, in the ventral premotor cortex, area F5 and later also in the inferior parietal lobule. Recent neuroimaging data indicate that the adult human brain is endowed with a "mirror neuron system," putatively containing mirror neurons and other neurons, for matching the observation and execution of actions. Mirror neurons may serve action recognition in monkeys as well as humans, whereas their putative role in imitation and language may be realized in human but not in monkey. This article shows the important role of computational models in providing sufficient and causal explanations for the observed phenomena involving mirror systems and the learning processes which form them, and underlines the need for additional circuitry to lift up the monkey mirror neuron circuit to sustain the posited cognitive functions attributed to the human mirror neuron system. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

  2. Laser cleaning of ITER's diagnostic mirrors

    Science.gov (United States)

    Skinner, C. H.; Gentile, C. A.; Doerner, R.

    2012-10-01

    Practical methods to clean ITER's diagnostic mirrors and restore reflectivity will be critical to ITER's plasma operations. We report on laser cleaning of single crystal molybdenum mirrors coated with either carbon or beryllium films 150 - 420 nm thick. A 1.06 μm Nd laser system provided 220 ns pulses at 8 kHz with typical power densities of 1-2 J/cm^2. The laser beam was fiber optically coupled to a scanner suitable for tokamak applications. The efficacy of mirror cleaning was assessed with a new technique that combines microscopic imaging and reflectivity measurements [1]. The method is suitable for hazardous materials such as beryllium as the mirrors remain sealed in a vacuum chamber. Excellent restoration of reflectivity for the carbon coated Mo mirrors was observed after laser scanning under vacuum conditions. For the beryllium coated mirrors restoration of reflectivity has so far been incomplete and modeling indicates that a shorter duration laser pulse is needed. No damage of the molybdenum mirror substrates was observed.[4pt][1] C.H. Skinner et al., Rev. Sci. Instrum. at press.

  3. Efficient Fluorescence Collection from Trapped Ion Qubits with an Integrated Spherical Mirror

    CERN Document Server

    Shu, G; Dietrich, M R; Blinov, B B

    2009-01-01

    Efficient collection of fluorescence from trapped ion qubits is crucial for qubit state detection and in generating ion-photon and remote ion entanglement. In a typical setup, only a few per cent of ion fluorescence is intercepted by the aperture of the imaging optics. We employ a simple metallic spherical mirror integrated with a linear Paul ion trap to achieve photon collection efficiency of at least 10% from a single Ba$^+$ ion qubit. An aspheric corrector is used to largely reduce the aberrations caused by the mirror and achieve high image quality.

  4. Thermo-optically driven adaptive mirror

    Science.gov (United States)

    Reinert, Felix; Lüthy, Willy

    2006-02-01

    The ideal adaptive optical mirror combines large aperture with high spatial and temporal resolution and a phase shift of at least 2π. Further, a simple low-cost solution is preferred. No adaptive system can perfectly fulfill all these requirements. We present a system that has the potential to reach this goal with the exception of high temporal resolution. But even with a moderate temporal resolution of one second such a system can find practical applications. For example as a laser resonator mirror that allows to modify the intensity distribution of the emission, or to correct slowly varying aberrations of optical systems. Two possible mechanisms can be used to change the optical path length of the adaptive mirror: thermal expansion of the mirror substrate or the thermally induced change of the refractive index (thermal dispersion) of a medium in front of the mirror. Both mechanisms have been shown to lead to promising results. In both cases heating was performed by irradiation of light in the active medium. The thermal dispersion based adaptive mirror is built with a thin layer of a liquid in front of a mirror. To allow a modification of the refractive index by irradiation with a diode laser at 808 nm, a suitable absorber is dissolved in the water. With chopped irradiation a resolution of 3.8 Hz at 30 % contrast is measured. This mirror has been used in a laser resonator to modify the output distribution of the laser. The thermal expansion based adaptive mirror is built with a thin layer of a silicon elastomer with a gold coated front side. We present a preparation method to produce thin films of Sylgard on sapphire. With an irradiated intensity of only 370 mW/cm2 surface modulations of up to 350 nm are obtained. With a test pattern a resolution of 1.6 line-pairs per millimeter at 30 % contrast is measured. The temporal resolution is better than one second.

  5. Exclusive lower extremity mirror movements and diastematomyelia.

    Science.gov (United States)

    Tubbs, R Shane; Smyth, Matthew D; Dure, Leon S; Oakes, W Jerry

    2004-01-01

    Mirror movements usually seen in the Klippel-Feil syndrome are most commonly appreciated in the upper extremities. Lower extremity involvement is seen rarely and when observed, is found in conjunction with upper extremity mirror movements. We report what we believe to be the first case of mirror movements found exclusively in the lower extremities in a female patient presenting with tethered cord syndrome. Our hopes are that this report will help elucidate mechanisms involved with these anomalous movements, as currently there is no commonly accepted etiology.

  6. What we know currently about mirror neurons.

    Science.gov (United States)

    Kilner, J M; Lemon, R N

    2013-12-02

    Mirror neurons were discovered over twenty years ago in the ventral premotor region F5 of the macaque monkey. Since their discovery much has been written about these neurons, both in the scientific literature and in the popular press. They have been proposed to be the neuronal substrate underlying a vast array of different functions. Indeed so much has been written about mirror neurons that last year they were referred to, rightly or wrongly, as "The most hyped concept in neuroscience". Here we try to cut through some of this hyperbole and review what is currently known (and not known) about mirror neurons. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Fine alignment of a large segmented mirror

    Science.gov (United States)

    Dey, Thomas William (Inventor)

    2010-01-01

    A system for aligning a segmented mirror includes a source of radiation directed along a first axis to the segmented mirror and a beamsplitter removably inserted along the first axis for redirecting radiation from the first axis to a second axis, substantially perpendicular to the first axis. An imaging array is positioned along the second axis for imaging the redirected radiation, and a knife-edge configured for cutting the redirected radiation is serially positioned to occlude and not occlude the redirected radiation, effectively providing a variable radiation pattern detected by the imaging array for aligning the segmented mirror.

  8. Fiber ring laser with a feedback mirror.

    Science.gov (United States)

    Abitan, H; Bohr, H; Pedersen, C F

    2005-12-20

    We describe the spectral and power features of a ytterbium-doped double-clad photonic crystal fiber laser that is operated in a ring configuration with an external mirror that feeds back only one of its two output beams. We compare the operation of the laser with and without an external feedback mirror. We find that the feedback mirror reduces significantly the spectral and power fluctuations. It is also responsible for an interesting spectral phenomenon: The laser frequency is drifting periodically over 9 nm at a rate of 2 nm/s from a short wavelength to a longer wavelength and vice versa.

  9. Tandem Mirror Reactor Systems Code (Version I)

    Energy Technology Data Exchange (ETDEWEB)

    Reid, R.L.; Finn, P.A.; Gohar, M.Y.; Barrett, R.J.; Gorker, G.E.; Spampinaton, P.T.; Bulmer, R.H.; Dorn, D.W.; Perkins, L.J.; Ghose, S.

    1985-09-01

    A computer code was developed to model a Tandem Mirror Reactor. Ths is the first Tandem Mirror Reactor model to couple, in detail, the highly linked physics, magnetics, and neutronic analysis into a single code. This report describes the code architecture, provides a summary description of the modules comprising the code, and includes an example execution of the Tandem Mirror Reactor Systems Code. Results from this code for two sensitivity studies are also included. These studies are: (1) to determine the impact of center cell plasma radius, length, and ion temperature on reactor cost and performance at constant fusion power; and (2) to determine the impact of reactor power level on cost.

  10. Some ideas on the choice of designs and materials for cooled mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Howells, M.R. [Lawrence Berkeley Lab., CA (United States)

    1995-02-01

    Here the author expresses some of his views on how the fabrication of future synchrotron beam-line optics ought to be approached. Many of the most interesting new ideas for beam-line mirrors, especially those with a promise of low costs, involve metals. Historically these materials had posed certain problems, but these have been overcome in recent times to the extent that the initial complement of Advanced-Light-Source (ALS) beam-line optics were made of metal and have met their specifications. To go furthere along that road one needs to get more interested in the metallurgical issues involved in making high-quality metal mirrors. The author recounts the results of some investigations into these materials questions and trys to draw on some of the experiences and achievements of these communities which have hitherto had only limited contact with synchrotron radiation researchers.

  11. Mirror, Mirror by the Stairs: The Impact of Mirror Exposure on Stair versus Elevator Use in College Students

    OpenAIRE

    Katie L Hodgin; Graham, Dan J.

    2016-01-01

    AbstractPrevious research has indicated that self-awareness-inducing mirrors can successfully incite behaviors that align with one’s personal values, such as helping others. Other research has found a large discrepancy between the high percentage of young adults who report valuing the healthfulness of physical activity (PA) and the low percentage who actually meet PA participation standards. Few studies, however, have examined how mirror exposure and both perceived and actual body size infl...

  12. Mirror, Mirror by the Stairs: The Impact of Mirror Exposure on Stair versus Elevator Use in College Students

    OpenAIRE

    Hodgin, Katie L.; Graham, Dan J.

    2016-01-01

    Previous research has indicated that self-awareness-inducing mirrors can successfully incite behaviors that align with one’s personal values, such as helping others. Other research has found a large discrepancy between the high percentage of young adults who report valuing the healthfulness of physical activity (PA) and the low percentage who actually meet PA participation standards. However, few studies have examined how mirror exposure and both perceived and actual body size influence highl...

  13. The ontogenetic origins of mirror neurons: evidence from 'tool-use' and 'audiovisual' mirror neurons.

    Science.gov (United States)

    Cook, Richard

    2012-10-23

    Since their discovery, mirror neurons--units in the macaque brain that discharge both during action observation and execution--have attracted considerable interest. Whether mirror neurons are an innate endowment or acquire their sensorimotor matching properties ontogenetically has been the subject of intense debate. It is widely believed that these units are an innate trait; that we are born with a set of mature mirror neurons because their matching properties conveyed upon our ancestors an evolutionary advantage. However, an alternative view is that mirror neurons acquire their matching properties during ontogeny, through correlated experience of observing and performing actions. The present article re-examines frequently overlooked neurophysiological reports of 'tool-use' and 'audiovisual' mirror neurons within the context of this debate. It is argued that these findings represent compelling evidence that mirror neurons are a product of sensorimotor experience, and not an innate endowment.

  14. The neuronal correlates of mirror therapy: an fMRI study on mirror induced visual illusions in patients with stroke.

    Science.gov (United States)

    Michielsen, Marian E; Smits, Marion; Ribbers, Gerard M; Stam, Henk J; van der Geest, Jos N; Bussmann, Johannes B J; Selles, Ruud W

    2011-04-01

    To investigate the neuronal basis for the effects of mirror therapy in patients with stroke. 22 patients with stroke participated in this study. The authors used functional MRI to investigate neuronal activation patterns in two experiments. In the unimanual experiment, patients moved their unaffected hand, either while observing it directly (no-mirror condition) or while observing its mirror reflection (mirror condition). In the bimanual experiment, patients moved both hands, either while observing the affected hand directly (no-mirror condition) or while observing the mirror reflection of the unaffected hand in place of the affected hand (mirror condition). A two-factorial analysis with movement (activity vs rest) and mirror (mirror vs no mirror) as main factors was performed to assess neuronal activity resultant of the mirror illusion. Data on 18 participants were suitable for analysis. Results showed a significant interaction effect of movement×mirror during the bimanual experiment. Activated regions were the precuneus and the posterior cingulate cortex (pmirror illusion in patients with stroke, the authors showed that during bimanual movement, the mirror illusion increases activity in the precuneus and the posterior cingulate cortex, areas associated with awareness of the self and spatial attention. By increasing awareness of the affected limb, the mirror illusion might reduce learnt non-use. The fact that the authors did not observe mirror-related activity in areas of the motor or mirror neuron system questions popular theories that attribute the clinical effects of mirror therapy to these systems.

  15. Driver ASICs for Advanced Deformable Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The program leverages on our extensive expertise in developing high-performance driver ASICs for deformable mirror systems and seeks to expand the capacities of the...

  16. Lightweight composite mirrors for telescopes Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Lightweight, steady and stiff mirrors are necessary to decrease cost of telescopes such as IXO and GenX used in special NASA missions. Low-density materials are...

  17. High Resolution Silicon Deformable Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal describes a plan to build a prototype small stroke, high precision deformable mirror suitable for space-based operation in systems for high-resolution...

  18. Polishing X-ray Mirror Mandrel

    Science.gov (United States)

    1999-01-01

    NASA's Space Optics Manufacturing Center has been working to expand our view of the universe via sophisticated new telescopes. The Optics Center's goal is to develop low-cost, advanced space optics technologies for the NASA program in the 21st century - including the long-term goal of imaging Earth-like planets in distant solar systems. To reduce the cost of mirror fabrication, Marshall Space Flight Center (MSFC) has developed replication techniques, the machinery, and materials to replicate electro-formed nickel mirrors. The process allows fabricating precisely shaped mandrels to be used and reused as masters for replicating high-quality mirrors. MSFC's Space Optics Manufacturing Technology Center (SOMTC) has grinding and polishing equipment ranging from conventional spindles to custom-designed polishers. These capabilities allow us to grind precisely and polish a variety of optical devices, including x-ray mirror mandrels. This image shows Charlie Griffith polishing the half-meter mandrel at SOMTC.

  19. Collimated Magnetron Sputter Deposition for Mirror Coatings

    DEFF Research Database (Denmark)

    Vickery, A.; Cooper-Jensen, Carsten P.; Christensen, Finn Erland

    2008-01-01

    At the Danish National Space Center (DNSC), a planar magnetron sputtering chamber has been established as a research and production coating facility for curved X-ray mirrors for hard X-ray optics for astronomical X-ray telescopes. In the following, we present experimental evidence that a collimat......At the Danish National Space Center (DNSC), a planar magnetron sputtering chamber has been established as a research and production coating facility for curved X-ray mirrors for hard X-ray optics for astronomical X-ray telescopes. In the following, we present experimental evidence...... that a collimation of the sputtered particles is an efficient way to suppress the interfacial roughness of the produced multilayer. We present two different types of collimation optimized for the production of low roughness curved mirrors and flat mirrors, respectively....

  20. High Resolution Silicon Deformable Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this proposal we describe a plan to build a deformable mirror suitable for space-based operation in systems for high-resolution imaging. The prototype DM will be...

  1. Cosmological Signals of a Mirror Twin Higgs

    CERN Document Server

    Craig, Nathaniel; Trott, Timothy

    2016-01-01

    We investigate the cosmology of the minimal model of neutral naturalness, the mirror Twin Higgs. The softly-broken mirror symmetry relating the Standard Model to its twin counterpart leads to significant dark radiation in tension with BBN and CMB observations. We quantify this tension and illustrate how it can be mitigated in several simple scenarios that alter the relative energy densities of the two sectors while respecting the softly-broken mirror symmetry. In particular, we consider both the out-of-equilibrium decay of a new scalar as well as reheating in a toy model of twinned inflation, Twinflation. In both cases the dilution of energy density in the twin sector does not merely reconcile the existence of a mirror Twin Higgs with cosmological constraints, but predicts contributions to cosmological observables that may be probed in current and future CMB experiments. This raises the prospect of discovering evidence of neutral naturalness through cosmology rather than colliders.

  2. Auditory–vocal mirroring in songbirds

    Science.gov (United States)

    Mooney, Richard

    2014-01-01

    Mirror neurons are theorized to serve as a neural substrate for spoken language in humans, but the existence and functions of auditory–vocal mirror neurons in the human brain remain largely matters of speculation. Songbirds resemble humans in their capacity for vocal learning and depend on their learned songs to facilitate courtship and individual recognition. Recent neurophysiological studies have detected putative auditory–vocal mirror neurons in a sensorimotor region of the songbird's brain that plays an important role in expressive and receptive aspects of vocal communication. This review discusses the auditory and motor-related properties of these cells, considers their potential role on song learning and communication in relation to classical studies of birdsong, and points to the circuit and developmental mechanisms that may give rise to auditory–vocal mirroring in the songbird's brain. PMID:24778375

  3. The mirror mechanism: recent findings and perspectives.

    Science.gov (United States)

    Rizzolatti, Giacomo; Fogassi, Leonardo

    2014-01-01

    Mirror neurons are a specific type of visuomotor neuron that discharge both when a monkey executes a motor act and when it observes a similar motor act performed by another individual. In this article, we review first the basic properties of these neurons. We then describe visual features recently investigated which indicate that, besides encoding the goal of motor acts, mirror neurons are modulated by location in space of the observed motor acts, by the perspective from which the others' motor acts are seen, and by the value associated with the object on which others' motor acts are performed. In the last part of this article, we discuss the role of the mirror mechanism in planning actions and in understanding the intention underlying the others' motor acts. We also review some human studies suggesting that motor intention in humans may rely, as in the monkey, on the mirror mechanism.

  4. Reflections on mirror neurons and speech perception.

    Science.gov (United States)

    Lotto, Andrew J; Hickok, Gregory S; Holt, Lori L

    2009-03-01

    The discovery of mirror neurons, a class of neurons that respond when a monkey performs an action and also when the monkey observes others producing the same action, has promoted a renaissance for the Motor Theory (MT) of speech perception. This is because mirror neurons seem to accomplish the same kind of one to one mapping between perception and action that MT theorizes to be the basis of human speech communication. However, this seeming correspondence is superficial, and there are theoretical and empirical reasons to temper enthusiasm about the explanatory role mirror neurons might have for speech perception. In fact, rather than providing support for MT, mirror neurons are actually inconsistent with the central tenets of MT.

  5. Silicon Wafer X-ray Mirror Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this one year research project, we propose to do the following four tasks;(1) Design the silicon wafer X-ray mirror demo unit and develop a ray-tracing code to...

  6. 130-nm tunable grating-mirror VCSEL

    DEFF Research Database (Denmark)

    Chung, Il-Sug; Mørk, Jesper

    2014-01-01

    We have reported that a combination of the high-index-contrast grating (HCG) mirror as movable mirror and the extended cavity configuration with an antireflection layer can provide a tuning wavelength range of 100 nm for tunable VCSELs. Here, we report that using the air-coupled cavity configurat......We have reported that a combination of the high-index-contrast grating (HCG) mirror as movable mirror and the extended cavity configuration with an antireflection layer can provide a tuning wavelength range of 100 nm for tunable VCSELs. Here, we report that using the air-coupled cavity...... configuration instead of the extended cavity configuration can bring 130-nm tuning range around 1330-nm wavelength. The air-coupled cavity is known to reduce the quantum confinement factor in VCSELs, increasing threshold. In our air-coupled cavity HCG VCSEL case, the very short power penetration length...

  7. Applied physics: Optical trapping for space mirrors.

    Science.gov (United States)

    McGloin, David

    2014-02-27

    Might it be possible to create mirrors for space telescopes, using nothing but microscopic particles held in place by light? A study that exploits a technique called optical binding provides a step towards this goal.

  8. Ultra-Lightweight Hybrid Structured Mirror Project

    Data.gov (United States)

    National Aeronautics and Space Administration — MMCC is proposing herewith a hybrid structured mirror that combines the advantages of SiC membrane and magnesium graphite composite. The significance of magnesium...

  9. Mirror Advanced Reactor Study interim design report

    Energy Technology Data Exchange (ETDEWEB)

    1983-04-01

    The status of the design of a tenth-of-a-kind commercial tandem-mirror fusion reactor is described at the midpoint of a two-year study. When completed, the design is to serve as a strategic goal for the mirror fusion program. The main objectives of the Mirror Advanced Reactor Study (MARS) are: (1) to design an attractive tandem-mirror fusion reactor producing electricity and synfuels (in alternate versions), (2) to identify key development and technology needs, and (3) to exploit the potential of fusion for safety, low activation, and simple disposal of radioactive waste. In the first year we have emphasized physics and engineering of the central cell and physics of the end cell. Design optimization and trade studies are continuing, and we expect additional modifications in the end cells to further improve the performance of the final design.

  10. Supersymmetric defect models and mirror symmetry

    Energy Technology Data Exchange (ETDEWEB)

    Hook, Anson; Kachru, Shamit; Torroba, Gonzalo

    2013-11-01

    We study supersymmetric field theories in three space-time dimensions doped by various configurations of electric charges or magnetic fluxes. These are supersymmetric avatars of impurity models. In the presence of additional sources such configurations are shown to preserve half of the supersymmetries. Mirror symmetry relates the two sets of configurations. We discuss the implications for impurity models in 3d NN = 4 QED with a single charged hypermultiplet (and its mirror, the theory of a free hypermultiplet) as well as 3d NN = 2 QED with one flavor and its dual, a supersymmetric Wilson-Fisher fixed point. Mirror symmetry allows us to find backreacted solutions for arbitrary arrays of defects in the IR limit of NN = 4 QED. Our analysis, complemented with appropriate string theory brane constructions, sheds light on various aspects of mirror symmetry, the map between particles and vortices and the emergence of ground state entropy in QED at finite density.

  11. Vibration damping for the Segmented Mirror Telescope

    Science.gov (United States)

    Maly, Joseph R.; Yingling, Adam J.; Griffin, Steven F.; Agrawal, Brij N.; Cobb, Richard G.; Chambers, Trevor S.

    2012-09-01

    The Segmented Mirror Telescope (SMT) at the Naval Postgraduate School (NPS) in Monterey is a next-generation deployable telescope, featuring a 3-meter 6-segment primary mirror and advanced wavefront sensing and correction capabilities. In its stowed configuration, the SMT primary mirror segments collapse into a small volume; once on location, these segments open to the full 3-meter diameter. The segments must be very accurately aligned after deployment and the segment surfaces are actively controlled using numerous small, embedded actuators. The SMT employs a passive damping system to complement the actuators and mitigate the effects of low-frequency (operating deflection shapes of the mirror and to quantify segment edge displacements; relative alignment of λ/4 or better was desired. The TMDs attenuated the vibration amplitudes by 80% and reduced adjacent segment phase mismatches to acceptable levels.

  12. Supersymmetric Defect Models and Mirror Symmetry

    CERN Document Server

    Hook, Anson; Torroba, Gonzalo

    2013-01-01

    We study supersymmetric field theories in three space-time dimensions doped by various configurations of electric charges or magnetic fluxes. These are supersymmetric avatars of impurity models. In the presence of additional sources such configurations are shown to preserve half of the supersymmetries. Mirror symmetry relates the two sets of configurations. We discuss the implications for impurity models in 3d N=4 QED with a single charged hypermultiplet (and its mirror, the theory of a free hypermultiplet) as well as 3d N=2 QED with one flavor and its dual, a supersymmetric Wilson-Fisher fixed point. Mirror symmetry allows us to find backreacted solutions for arbitrary arrays of defects in the IR limit of N=4 QED. Our analysis, complemented with appropriate string theory brane constructions, sheds light on various aspects of mirror symmetry, the map between particles and vortices and the emergence of ground state entropy in QED at finite density.

  13. Silicon Wafer X-ray Mirror Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this one year research project, we propose to do the following four tasks; (1) Design the silicon wafer X-ray mirror demo unit and develop a ray-tracing code to...

  14. Reflective Properties of a Parabolic Mirror.

    Science.gov (United States)

    Ramsey, Gordon P.

    1991-01-01

    An incident light ray parallel to the optical axis of a parabolic mirror will be reflected at the focal point and vice versa. Presents a mathematical proof that uses calculus, algebra, and geometry to prove this reflective property. (MDH)

  15. Mirror aneurysms : a reflection on natural history

    NARCIS (Netherlands)

    Meissner, Irene; Torner, James; Huston III, John; Rajput, Michele L.; Wiebers, David O.; Jones, Lyell K.; Brown, Robert D.; Groen, Rob

    2012-01-01

    OBJECT: Investigators conducting the International Study of Unruptured Intracranial Aneurysms, sponsored by the National Institutes of Health, sought to evaluate predictors of future hemorrhage in patients who had unruptured mirror aneurysms. These paired aneurysms in bilateral arterial positions mi

  16. James Webb Space Telescope Primary Mirror Manufacturing

    Science.gov (United States)

    Lightsey, Paul; Gallagher, B.; Chaney, D.; Brown, B.

    2009-01-01

    The James Webb Space Telescope has a segmented primary mirror consisting of 18 hexagonal beryllium primary mirror segment assemblies (PMSA) that have a total collecting area greater than 25 square meters. The PMSAs are designed to operate at cryogenic temperatures (39 K) and to be actively controlled to co-phase the segments. This paper discusses the processes and testing utilized in the manufacture of these mirrors including the critical cryogenic testing performed at the XRCF facility at the NASA Marshall Space Flight Center. The manufacturing team is headed by Ball Aerospace & Technologies Corp (BATC) with support from Brush Wellman for beryllium blank fabrication, Axsys Technologies for the precision machining, L3-Tinsley for the mirror polishing, and QCI for the reflective coating application.

  17. Primary mirror segment fabrication for CELT

    Science.gov (United States)

    Mast, Terry S.; Nelson, Jerry E.; Sommargren, Gary E.

    2000-07-01

    The primary mirror of the proposed California Extremely Large Telescope is a 30-meter diameter mosaic of hexagonal segments. An initial design calls for about a thousand segments with a hexagon side length of 0.5 meters, a primary-mirror focal ratio of 1.5, and a segment surface quality of about 20 nanometers rms. We describe concepts for fabricating these segments.

  18. Authors’ response: mirror neurons: tests and testability.

    Science.gov (United States)

    Catmur, Caroline; Press, Clare; Cook, Richard; Bird, Geoffrey; Heyes, Cecilia

    2014-04-01

    Commentators have tended to focus on the conceptual framework of our article, the contrast between genetic and associative accounts of mirror neurons, and to challenge it with additional possibilities rather than empirical data. This makes the empirically focused comments especially valuable. The mirror neuron debate is replete with ideas; what it needs now are system-level theories and careful experiments – tests and testability.

  19. Anomalous Mirror Symmetry Generated by Optical Illusion

    Directory of Open Access Journals (Sweden)

    Kokichi Sugihara

    2016-04-01

    Full Text Available This paper introduces a new concept of mirror symmetry, called “anomalous mirror symmetry”, which is physically impossible but can be perceived by human vision systems because of optical illusion. This symmetry is characterized geometrically and a method for creating cylindrical surfaces that create this symmetry is constructed. Examples of solid objects constructed by a 3D printer are also shown.

  20. On horizonless temperature with an accelerating mirror

    Science.gov (United States)

    Good, Michael R. R.; Yelshibekov, Khalykbek; Ong, Yen Chin

    2017-03-01

    A new solution of a unitary moving mirror is found to produce finite energy and emit thermal radiation despite the absence of an acceleration horizon. In the limit that the mirror approaches the speed of light, the model corresponds to a black hole formed from the collapse of a null shell. For speeds less than light, the black hole correspondence, if it exists, is that of a remnant.

  1. On Horizonless Temperature with an Accelerating Mirror

    CERN Document Server

    Good, Michael R R; Ong, Yen Chin

    2016-01-01

    A new solution of a unitary moving mirror is found to produce finite energy and emit thermal radiation despite the absence of an acceleration horizon. In the limit that the mirror approaches the speed of light, the model corresponds to a black hole formed from the collapse of a null shell. For speeds less than light, the black hole correspondence, if it exists, is that of a remnant.

  2. Action observation: Inferring intentions without mirror neurons

    DEFF Research Database (Denmark)

    Frith, Christopher; Kilner, James M

    2008-01-01

    A recent study has shown, using fMRI, that the mirror neuron system does not mediate action understanding when the observed action is novel or when it is hard to understand.......A recent study has shown, using fMRI, that the mirror neuron system does not mediate action understanding when the observed action is novel or when it is hard to understand....

  3. Cryogenic Test Results of Hextek Mirror

    Science.gov (United States)

    Hadaway, James; Stahl, H. Philip; Eng, Ron; Hogue, William

    2004-01-01

    A 250 mm diameter lightweight borosilicate mirror has been interferometrically tested from room-temperature down to 30 K at the X-Ray Calibration Facility (XRCF) at Marshall Space Flight Center (MSFC). The minor blank was manufactured by Hextek Corporation using a high-temperature gas fusion process and was then polished at MSFC. It is a sandwich-type mirror consisting of a thin face-sheet (approx.1.5 mm thick), a core structure (20 mm thick, approx.43 mm diameter cells, & 0.5-1.2 mm thick walls), and a thin back-sheet (3 mm thick). The mirror has a 2500 mm spherical radius-of- curvature @/lo). The areal density is 14 kg/sq m. The mirror was tested in the 1 m x 2 m chamber using an Instantaneous Phase Interferometer (PI) from ADE Phase Shift Technologies. The mirror was tested twice. The first test measured the change in surface figure from ambient to 30 K and the repeatability of the change. An attempt was then made by QED Technologies to cryo-figure the mirror using magnetorheological finishing. The second test measured the effectiveness of the cryo- figuring. This paper will describe the test goals, the test instrumentation, and the test results for these cryogenic tests.

  4. Lithium-based electrochromic mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Richardson, Thomas J.; Slack, Jonathan L.

    2003-05-19

    Antimony, antimony-copper, and antimony-silver thin films were prepared by DC magnetron sputtering on glass substrates. Their reflectance and transmittance in the visible range were measured before and after electrochemical lithiation. The mixed metal films exhibited larger changes in reflectance and small shifts in the optical absorption edge compared with pure antimony films. Electrochromic cycling speed and stability of the Sb-Li system were improved by the addition of copper and silver.

  5. Research on the optimization of a bimorph piezoelectric deformable mirror based on zeroth-order method

    Science.gov (United States)

    Wang, Hairen; Hu, Lin

    2016-07-01

    The deformable mirror adjusts the mirror surface shape to compensate the wavefront error in the adaptive optics system. Recently, the adaptive optics has been widely used in many applications, such as astronomical telescopes, high power laser systems, etc. These applications require large diameter deformable mirrors with large stroke, high speed and low cost. Thus, the bimorph piezoelectric deformable mirror, which is a good match for the applications, has attracted more and more attentions. In this paper, we use zeroth-order optimization method to optimize the physical parameters of a bimorph piezoelectric deformable mirror that consists of a metal reflective layer deposited on the top of a slim piezoelectric ceramic surface layer. The electrodes are deposited on the bottom of the piezoelectric ceramic layer. The physical parameters to be optimized include the optimal thickness ratio between the piezoelectric layer and reflective layer, inter-electrode distance, and so on. A few reasonable designs are obtained by a comparative study presented for three geometries of electrodes, which are circular, square and hexagon, respectively.

  6. Active optics: variable curvature mirrors for ELT laser guide star refocusing systems

    Science.gov (United States)

    Challita, Zalpha; Hugot, Emmanuel; Madec, Fabrice; Ferrari, Marc; Le Mignant, David; Vivès, Sébastien; Cuby, Jean-Gabriel

    2011-10-01

    The future generation of Extremely Large Telescopes will require a complex combination of technologies for adaptive optics (AO) systems assisted by laser guide stars (LGS). In this context, the distance from the LGS spot to the telescope pupil ranges from about 80 to 200 km, depending on the Sodium layer altitude and the elevation of the telescope. This variation leads to a defocusing effect on the LGS wave-front sensor which needs to be compensated. We propose an active mirror able to compensate for this variation, based on an original optical design including this active optics component. This LGS Variable Curvature Mirror (LGS-VCM) is a 120 mm spherical active mirror able to achieve 820 μm deflection sag with an optical quality better than 150 nm RMS, allowing the radius of curvature variation from F/12 to F/2. Based on elasticity theory, the deformation of the metallic mirror is provided by an air pressure applied on a thin meniscus with a variable thickness distribution. In this article, we detail the analytical development leading to the specific geometry of the active component, the results of finite element analysis and the expected performances in terms of surface error versus the range of refocalisation. Three prototypes have been manufactured to compare the real behavior of the mirror and the simulations data. Results obtained on the prototypes are detailed, showing that the deformation of the VCM is very close to the simulation, and leads to a realistic active concept.

  7. Optical Performance Modeling of FUSE Telescope Mirror

    Science.gov (United States)

    Saha, Timo T.; Ohl, Raymond G.; Friedman, Scott D.; Moos, H. Warren

    2000-01-01

    We describe the Metrology Data Processor (METDAT), the Optical Surface Analysis Code (OSAC), and their application to the image evaluation of the Far Ultraviolet Spectroscopic Explorer (FUSE) mirrors. The FUSE instrument - designed and developed by the Johns Hopkins University and launched in June 1999 is an astrophysics satellite which provides high resolution spectra (lambda/Delta(lambda) = 20,000 - 25,000) in the wavelength region from 90.5 to 118.7 nm The FUSE instrument is comprised of four co-aligned, normal incidence, off-axis parabolic mirrors, four Rowland circle spectrograph channels with holographic gratings, and delay line microchannel plate detectors. The OSAC code provides a comprehensive analysis of optical system performance, including the effects of optical surface misalignments, low spatial frequency deformations described by discrete polynomial terms, mid- and high-spatial frequency deformations (surface roughness), and diffraction due to the finite size of the aperture. Both normal incidence (traditionally infrared, visible, and near ultraviolet mirror systems) and grazing incidence (x-ray mirror systems) systems can be analyzed. The code also properly accounts for reflectance losses on the mirror surfaces. Low frequency surface errors are described in OSAC by using Zernike polynomials for normal incidence mirrors and Legendre-Fourier polynomials for grazing incidence mirrors. The scatter analysis of the mirror is based on scalar scatter theory. The program accepts simple autocovariance (ACV) function models or power spectral density (PSD) models derived from mirror surface metrology data as input to the scatter calculation. The end product of the program is a user-defined pixel array containing the system Point Spread Function (PSF). The METDAT routine is used in conjunction with the OSAC program. This code reads in laboratory metrology data in a normalized format. The code then fits the data using Zernike polynomials for normal incidence

  8. Primary mirror assemblies for large space telescopes

    Science.gov (United States)

    Malamed, Evgeny R.; Sokolsky, M. N.

    1995-09-01

    In this report are considered the basic problems which relate to developemnt, manufacture, experimental trying out, and usage of primary mirrors (PM) of the large space telescopes intended to perform distant sounding of the Earth. Attention is concentrated on development of weight-reduced passive mirrors which ensure more reliable operation of the telescope as a whole. In the report we expressed the opinion that it is quite possible to manufacture a passive weight-reduced PM if its diameter is equal approximately to 3 m. Materials which may be used for the manufacturing of PM are beryllium and silicon carbide, physical and mechanical parameters of which are the most preferable ones. But it should be taken into consideration that this is the glass ceramic of CO115M brand which has been mastered by the industry of Russia in the greatest extent. It was confirmed that parameters of this material remain unchanged during a long period of time. Constructions of the PM, made of glass ceramic, as well as constructions of holders intended to fix the mirror, are presented in this report. A holder is used first of all to prevent lowering of a PM surface quality after a mirror has been removed from a machine and fixed in a primary mirror assembly (PMA). At present two-layer construction of a PM is preferable. This construction consists of thick base including weight reduction structure, which is in a radius which is optimum from the standpoint of deformation of a mirror operating surface. In the process of manufacture a mirror is deprived of its weight with the use of special pneumatic off-loading elements. PMA is erected in vertical plane by means of using an interferometric inspection system. In the end of this report we expressed the views on an approach to engineering of a PM by taking into account potentialities both of space ships and of carrier rockets.

  9. Mirror, mirror on the wall, how does my brain recognize my image at all?

    Directory of Open Access Journals (Sweden)

    David L Butler

    Full Text Available For decades researchers have used mirrors to study self-recognition. However, attempts to identify neural processes underlying this ability have used photographs instead. Here we used event related potentials (ERPs to compare self-face recognition in photographs versus mirrors and found distinct neural signatures. Measures of visual self-recognition are therefore not independent of the medium employed.

  10. Integration of Mirror Design with Suspension System using NASA's New Mirror Modeling Software

    Science.gov (United States)

    Arnold,William R., Sr.; Bevan, Ryan M.; Stahl, Philip

    2013-01-01

    Advances in mirror fabrication are making very large space based telescopes possible. In many applications, only monolithic mirrors can meet the performance requirements. The existing and near-term planned heavy launch vehicles place a premium on lowest possible mass, and then available payload shroud sizes limit near term designs to 4 meter class mirrors. Practical 8 meter class and beyond designs could encourage planners to include larger shrouds, if it can be proven that such mirrors can be manufactured. These two factors, lower mass and larger mirrors, present the classic optimization problem. There is a practical upper limit to how large of a mirror can be supported by a purely kinematic mount system handling both operational and launch loads. This paper shows how the suspension system and mirror blank need to be designed simultaneously. We will also explore the concepts of auxiliary support systems which act only during launch and disengage on orbit. We will define required characteristics of these systems and show how they can substantially reduce the mirror mass.

  11. Specular Reflections: John Brett and the Mirror of Venus

    Directory of Open Access Journals (Sweden)

    James Mussell

    2013-10-01

    Full Text Available Normal 0 false false false EN-GB X-NONE X-NONE MicrosoftInternetExplorer4 When John Brett, the Pre-Raphaelite painter and astronomer, presented his theory of specular reflection in Venus to the Royal Astronomical Society, he provoked a controversy over both the constitution of the planet and the learned society. Brett thought Venus was most likely a ball of molten metal enclosed in a glass envelope and this raised the tantalizing possibility that it might function as a mirror, reflecting back an image of the earth. A few months later another 'Mirror of Venus 'was displayed at the Grosvenor Gallery. The surface of Edward Burne-Jones's painting provides a different model of reflection but one that illuminates the space of the Royal Astronomical Society and the practice of astronomy more broadly. Using Burne-Jones’s painting as a point of comparison, I argue that Brett’s astronomy put into play a desiring, viewing subject that was disavowed in his landscape art.

  12. Enabling materials and processes for large aerospace mirrors

    Science.gov (United States)

    Matson, Lawrence E.; Chen, Ming Y.

    2008-07-01

    The use of monolithic glass to produce large, rigid segmented members for lightweight space-based mirror systems appears to have reached its limits due to the long production lead times, high processing costs, and launch load/weight requirements. New material solutions and processes are required to meet the US Air Force's optical needs for directed energy, reconnaissance/surveillance, and communications. Mirror structural substrates made out of advanced materials (metal, ceramic, and polymer), composites, foams, and microsphere arrays should allow for CTE and modulus tailorability, low-density, and high values in strength, stiffness, thermal conductivity and toughness. Conventional mechanical polishing to visual specifications for figure and surface finish roughness requirements will be difficult, due to the multi-phase complexities of these new systems. Advances in surface removal technologies as well as replication processes will be required to produce the required optical finishes with reduced schedule and cost. In this paper selected material and process solutions being considered will be discussed.

  13. Study of tin amalgam mirrors by 1 1 9 Sn Mössbauer spectroscopy and other analytical methods

    Science.gov (United States)

    Lerf, A.; Wagner, F. E.; Herrera, L. K.; Justo, A.; Mu noz-Páez, A.; Pérez-Rodríguez, J. L.

    2016-12-01

    From the beginning of the 16 th until the end of the 19 th century the most widely used mirrors consisted of a pane of glass backed with a reflecting layer of tin-mercury amalgam. They were made by sliding the glass pane over a tin foil covered with liquid mercury. After removal of the superfluous mercury, tin amalgam formed slowly at ambient temperature and yielded a reflecting layer adhering to the surface of the glass. Such mirrors often deteriorate in the course of time by oxidation of the tin in the amalgam to stannous or stannic oxide. 119Sn Mössbauer spectroscopy, scanning electron microscopy, micro-XRF and X-ray diffraction have been used to study this deterioration process. The studied specimens were a modern mirror made for the reconstruction of the Green Vault in Dresden in the early 2000s, two rather well preserved German mirrors from the 17 th and 19 th centuries and several strongly deteriorated specimens of Baroque mirrors from the south of Spain. The modern mirror consists mainly of a Sn0.9Hg0.1 amalgam with only 2 % of SnO2. The older German mirrors showed more pronounced oxidation, containing 12 and 15 % of SnO2, which did not noticeably impair their reflectivity. In the samples from the Spanish mirrors at best a few percent of metallic phase was left. The majority of the tin had oxidised to SnO2, but between 8 and 20 % of the tin was present as SnO. X-ray diffraction yielded similar results and micro-XRF mapping using synchrotron radiation for excitation gave information on the distribution of Sn and Hg in the reflecting layer of the mirrors.

  14. Study of tin amalgam mirrors by {sup 119}Sn Mössbauer spectroscopy and other analytical methods

    Energy Technology Data Exchange (ETDEWEB)

    Lerf, A. [Bavarian Academy of Sciences, Walther Meißner Institute (Germany); Wagner, F. E., E-mail: fwagner@tum.de [Technical University of Munich, Physics Department E15 (Germany); Herrera, L. K. [Universidad Nacional de Colombia. Dpto. de Ingeniería Mecánica y Mecatrónica (Colombia); Justo, A.; Mu noz-Páez, A.; Pérez-Rodríguez, J. L. [University of Sevilla-CSIC, ICMSE (Spain)

    2016-12-15

    From the beginning of the 16 {sup th} until the end of the 19 {sup th} century the most widely used mirrors consisted of a pane of glass backed with a reflecting layer of tin-mercury amalgam. They were made by sliding the glass pane over a tin foil covered with liquid mercury. After removal of the superfluous mercury, tin amalgam formed slowly at ambient temperature and yielded a reflecting layer adhering to the surface of the glass. Such mirrors often deteriorate in the course of time by oxidation of the tin in the amalgam to stannous or stannic oxide. {sup 119}Sn Mössbauer spectroscopy, scanning electron microscopy, micro-XRF and X-ray diffraction have been used to study this deterioration process. The studied specimens were a modern mirror made for the reconstruction of the Green Vault in Dresden in the early 2000s, two rather well preserved German mirrors from the 17 {sup th} and 19 {sup th} centuries and several strongly deteriorated specimens of Baroque mirrors from the south of Spain. The modern mirror consists mainly of a Sn{sub 0.9}Hg{sub 0.1} amalgam with only 2 % of SnO{sub 2}. The older German mirrors showed more pronounced oxidation, containing 12 and 15 % of SnO{sub 2}, which did not noticeably impair their reflectivity. In the samples from the Spanish mirrors at best a few percent of metallic phase was left. The majority of the tin had oxidised to SnO{sub 2}, but between 8 and 20 % of the tin was present as SnO. X-ray diffraction yielded similar results and micro-XRF mapping using synchrotron radiation for excitation gave information on the distribution of Sn and Hg in the reflecting layer of the mirrors.

  15. The Mirror Program: Preparing Women for the Postoperative Mastectomy Mirror-Viewing Experience.

    Science.gov (United States)

    Freysteinson, Wyona M; Deutsch, Amy S; Davin, Karen; Lewis, Carol; Sisk, Angela; Sweeney, Lilian; Wuest, Linda; Cesario, Sandra K

    2015-01-01

    Preparing women for the experiences they will endure during the breast cancer trajectory improves psychological outcomes and quality of life. Women have found that it may be difficult to view themselves in a mirror after having a mastectomy. Supporting women who have had a mastectomy in mirror-viewing and body image is a relatively new yet important intervention in oncology nursing. The feasibility of a preoperative mirror program given by oncology nurse navigators to women who were scheduled for a mastectomy was examined in this randomized control study. Pre- and postoperative data on anxiety, body image, depression, emotional well-being, and mirror use were collected from intervention participants (n = 10) and control subjects (n = 9). This article illustrates the development of the mirror program and the results of the feasibility trial, and provides a discussion with implications for future research. © 2014 Wiley Periodicals, Inc.

  16. Optomechanical design software for segmented mirrors

    Science.gov (United States)

    Marrero, Juan

    2016-08-01

    The software package presented in this paper, still under development, was born to help analyzing the influence of the many parameters involved in the design of a large segmented mirror telescope. In summary, it is a set of tools which were added to a common framework as they were needed. Great emphasis has been made on the graphical presentation, as scientific visualization nowadays cannot be conceived without the use of a helpful 3d environment, showing the analyzed system as close to reality as possible. Use of third party software packages is limited to ANSYS, which should be available in the system only if the FEM results are needed. Among the various functionalities of the software, the next ones are worth mentioning here: automatic 3d model construction of a segmented mirror from a set of parameters, geometric ray tracing, automatic 3d model construction of a telescope structure around the defined mirrors from a set of parameters, segmented mirror human access assessment, analysis of integration tolerances, assessment of segments collision, structural deformation under gravity and thermal variation, mirror support system analysis including warping harness mechanisms, etc.

  17. Some Implications of Neutron Mirror Neutron Oscillation

    CERN Document Server

    Mohapatra, Rabindra N; Nussinov, S

    2005-01-01

    We comment on a recently discussed possibility of oscillations between neutrons and degenerate mirror neutrons in the context of mirror models for particles and forces. It has been noted by Bento and Berezhiani that if these oscillations occurred at a rate of $\\tau^{-1}_{NN'}\\sim sec^{-1}$, it would help explain putative super GKZ cosmic ray events provided the temperature of the mirror radiation is $\\sim 0.3-0.4$ times that of familiar cosmic microwave background radiation. We discuss how such oscillation time scales can be realized in mirror models and find that the simplest nonsupersymmetric model for this idea requires the existence of a low mass (30-3000 GeV) color triplet scalar or vector boson. A supersymmetric model, where this constraint can be avoided is severely constrained by the requirement of maintaining a cooler mirror sector. We also find that the reheat temperature after inflation in generic models that give fast $n-n'$ oscillation be less than about 100 GeV in order to maintain the required ...

  18. Mirror, Mirror by the Stairs: The Impact of Mirror Exposure on Stair versus Elevator Use in College Students

    Directory of Open Access Journals (Sweden)

    Katie L Hodgin

    2016-04-01

    Full Text Available AbstractPrevious research has indicated that self-awareness-inducing mirrors can successfully incite behaviors that align with one’s personal values, such as helping others. Other research has found a large discrepancy between the high percentage of young adults who report valuing the healthfulness of physical activity (PA and the low percentage who actually meet PA participation standards. Few studies, however, have examined how mirror exposure and both perceived and actual body size influence highly-valued PA participation among college students. The present study assessed stair versus elevator use on a western college campus and hypothesized that mirror exposure would increase the more personally-healthy transportation method of stair use. In accordance with previous research, it was also hypothesized that males and those with a lower body mass index (BMI would be more likely to take the stairs, and that body-size distorting mirrors would impact the stair-elevator decision. One hundred and sixty-seven students (51% male enrolled in an introductory psychology course were recruited to take a survey about their transportation choices at an indoor campus parking garage. Participants were individually exposed to either no mirror, a standard full-length mirror, or a full-length mirror manipulated to make the reflected body size appear either slightly thinner or slightly wider than normal before being asked to go to the fourth floor of the garage for a survey. Participants’ choice of floor climbing method (stairs or elevator was recorded and they were administered an internet-based survey assessing demographic information, BMI, self-awareness, perceived body size, and other variables likely to be associated with stair use. Results from logistic regression analyses revealed that participants who were not exposed to a mirror (OR = 0.37, 95% CI: 0.14 – 0.96, males (OR = 0.33, 95% CI: 0.13 – 0.85, those with lower BMI (OR = 0.84, 95% CI: 0.71

  19. Mirror, Mirror by the Stairs: The Impact of Mirror Exposure on Stair versus Elevator Use in College Students.

    Science.gov (United States)

    Hodgin, Katie L; Graham, Dan J

    2016-01-01

    Previous research has indicated that self-awareness-inducing mirrors can successfully incite behaviors that align with one's personal values, such as helping others. Other research has found a large discrepancy between the high percentage of young adults who report valuing the healthfulness of physical activity (PA) and the low percentage who actually meet PA participation standards. However, few studies have examined how mirror exposure and both perceived and actual body size influence highly valued PA participation among college students. The present study assessed stair versus elevator use on a western college campus and hypothesized that mirror exposure would increase the more personally healthy transportation method of stair use. In accordance with previous research, it was also hypothesized that males and those with a lower body mass index (BMI) would be more likely to take the stairs, and that body size distorting mirrors would impact the stair-elevator decision. One hundred sixty-seven students (51% male) enrolled in an introductory psychology course were recruited to take a survey about their "transportation choices" at an indoor campus parking garage. Participants were individually exposed to either no mirror, a standard full-length mirror, or a full-length mirror manipulated to make the reflected body size appear either slightly thinner or slightly wider than normal before being asked to go to the fourth floor of the garage for a survey. Participants' choice of floor-climbing method (stairs or elevator) was recorded, and they were administered an Internet-based survey assessing demographic information, BMI, self-awareness, perceived body size, and other variables likely to be associated with stair use. Results from logistic regression analyses revealed that participants who were not exposed to a mirror [odds ratios (OR) = 0.37, 95% CI: 0.14-0.96], males (OR = 0.33, 95% CI: 0.13-0.85), those with lower BMI (OR = 0.84, 95% CI: 0.71-0.99), those

  20. VLT beryllium secondary mirror no. 1: performance review

    Science.gov (United States)

    Cayrel, Marc

    1998-08-01

    The four Very Large Telescope secondary mirrors are 1.2-m Beryllium lightweight convex mirrors. REOSC has been selected for the design and manufacturing of the optics and of their supporting system. The first mirror unit has been delivered in September, 1997. Operating from visible to near infrared, the mirror defines the telescope aperture stop and may be chopped during observation. The optical requirements are tight and a high stiffness, low weight and inertia are requested as well. Using beryllium is a technical challenge for such a large optic manufacturing, in particular regarding its stability. The requirements and design are presented, we review the mirror manufacturing steps: blank production, machining, grinding, Nickel plating, polishing, integration and testing. The optical quality control method, a problem for large convex mirrors control, is detailed. The results of acceptance testing of mirror No. 1 are summarized, we present conclusions about the mirror figure stability. The status of the three additional mirrors manufacturing is presented to conclude.

  1. Four-mirror extreme ultraviolet (EUV) lithography projection system

    Science.gov (United States)

    Cohen, Simon J; Jeong, Hwan J; Shafer, David R

    2000-01-01

    The invention is directed to a four-mirror catoptric projection system for extreme ultraviolet (EUV) lithography to transfer a pattern from a reflective reticle to a wafer substrate. In order along the light path followed by light from the reticle to the wafer substrate, the system includes a dominantly hyperbolic convex mirror, a dominantly elliptical concave mirror, spherical convex mirror, and spherical concave mirror. The reticle and wafer substrate are positioned along the system's optical axis on opposite sides of the mirrors. The hyperbolic and elliptical mirrors are positioned on the same side of the system's optical axis as the reticle, and are relatively large in diameter as they are positioned on the high magnification side of the system. The hyperbolic and elliptical mirrors are relatively far off the optical axis and hence they have significant aspherical components in their curvatures. The convex spherical mirror is positioned on the optical axis, and has a substantially or perfectly spherical shape. The spherical concave mirror is positioned substantially on the opposite side of the optical axis from the hyperbolic and elliptical mirrors. Because it is positioned off-axis to a degree, the spherical concave mirror has some asphericity to counter aberrations. The spherical concave mirror forms a relatively large, uniform field on the wafer substrate. The mirrors can be tilted or decentered slightly to achieve further increase in the field size.

  2. Integration of Micro-Electro-Mechanical Deformable Mirrors in Doped Fiber Amplifiers

    CERN Document Server

    Bouyge, D; Crunteanu, A; Blondy, P; Couderc, V; Lhermite, J; Grossard, L; Barthélemy, A

    2007-01-01

    We present a simple technique to produce active Q-switching in various types of fiber amplifiers by active integration of an electrostatic actuated deformable metallic micro-mirror. The optical MEMS (MOEMS) device acts as one of the laser cavity reflectors and, at the same time, as switching/ modulator element. We aim to obtain laser systems emitting short, high-power pulses and having variable repetition rate. The electro-mechanical behavior of membrane (bridge-type) was simulated by using electrostatic and modal 3D finite element analysis (FEA). The results of the simulations fit well with the experimental mechanical, electrical and thermal measurements of the components. In order to decrease the sensitiveness to fiber-mirror alignment we are developing novel optical devices based on stressed-metal cantilever-type geometry that allow deflections up to 50 $\\mu$m with increased reflectivity discrimination during actuation.

  3. Benefits of metal reflective surfaces for concentrating solar applications

    Science.gov (United States)

    Braendle, Stefan

    2010-08-01

    Concentrating photovoltaic (CPV) companies are constantly making gains in efficiency and a lower levelized cost of energy, but continue to face questions of reliability and efficiency at scale remain. New technologies such as highly efficient aluminum mirrors help CPV companies fulfill both of these demands by allowing for performance and reliability gains, while also enabling high volume production for scaled deployment. In testing, metal mirrors have shown to be good matches for concentrating applications while performing at the same level as glass mirrors in accelerated weather tests. When combined with the inherent lighter weight and formability of aluminum, these new mirrors provide CPV solutions with a compelling advantage in the field.

  4. Cryogenic wavefront correction using membrane deformable mirrors.

    Science.gov (United States)

    Dyson, H; Sharples, R; Dipper, N; Vdovin, G

    2001-01-01

    Micro-machined membrane deformable mirrors (MMDMs) are being evaluated for their suitability as wavefront correctors at cryogenic temperatures. Presented here are experimental results for the change in the initial mirror figure of 37-channel MMDMs from OKO Technologies upon cooling to T=78K. The changes in the influence functions are also explored. Of the sample of 3 mirrors tested, one was found to have sufficiently small initial static aberrations to be useful as a wavefront corrector at this temperature. The influence functions at T=78K were found to be similar in shape to both those at room temperature and theoretical predictions of the MMDMs surface shape. The magnitude of the surface deflection at T=78K was reduced by around 20% compared with room temperature values.

  5. Massive Particle Reflection from Moving Mirrors

    Science.gov (United States)

    Sfarti, Adrian

    2016-09-01

    We investigate the reflection of massive particles from moving mirrors. The adoption of the formalism based on the energy-momentum allowed us to derive the most general set of formulas, valid for massive and, in the limit, also for massless particles. We show that the momentum change of the reflecting particle always lies along the normal to the mirror, independent of the mirror speed. The subject is interesting not only to physicists designing concentrators for fascicles of massive particles and electron microscopes but also to computer scientists working in raytracing operating in the photon sector. The paper, far from being only theoretical, has profound and novel practical applications in both domains of engineering design and computer science.

  6. High-dispersive mirrors for femtosecond lasers.

    Science.gov (United States)

    Pervak, V; Teisset, C; Sugita, A; Naumov, S; Krausz, F; Apolonski, A

    2008-07-07

    We report on the development of highly dispersive mirrors for chirped-pulse oscillators (CPO) and amplifiers (CPA). In this proof-of-concept study, we demonstrate the usability of highly dispersive multilayer mirrors for high-energy femtosecond oscillators, namely for i) a chirped-pulse Ti:Sa oscillator and ii) an Yb:YAG disk oscillator. In both cases a group delay dispersion (GDD) of the order of 2x10(4) fs(2) was introduced, accompanied with an overall transmission loss as low as approximately 2 per cent. This unprecedented combination of high dispersion and low loss over a sizeable bandwidth with multilayer structures opens the prospects for femtosecond CPA systems equipped with a compact, alignment-insensitive all-mirror compressors providing compensation of GDD as well as higher-order dispersion.

  7. Homological mirror symmetry and tropical geometry

    CERN Document Server

    Catanese, Fabrizio; Kontsevich, Maxim; Pantev, Tony; Soibelman, Yan; Zharkov, Ilia

    2014-01-01

    The relationship between Tropical Geometry and Mirror Symmetry goes back to the work of Kontsevich and Y. Soibelman (2000), who applied methods of non-archimedean geometry (in particular, tropical curves) to Homological Mirror Symmetry. In combination with the subsequent work of Mikhalkin on the “tropical” approach to Gromov-Witten theory, and the work of Gross and Siebert, Tropical Geometry has now become a powerful tool. Homological Mirror Symmetry is the area of mathematics concentrated around several categorical equivalences connecting symplectic and holomorphic (or algebraic) geometry. The central ideas first appeared in the work of Maxim Kontsevich (1993). Roughly speaking, the subject can be approached in two ways: either one uses Lagrangian torus fibrations of Calabi-Yau manifolds (the so-called Strominger-Yau-Zaslow picture, further developed by Kontsevich and Soibelman) or one uses Lefschetz fibrations of symplectic manifolds (suggested by Kontsevich and further developed by Seidel). Tropical Ge...

  8. Conference on Complex Geometry and Mirror Symmetry

    CERN Document Server

    Vinet, Luc; Yau, Shing-Tung; Mirror Symmetry III

    1999-01-01

    This book presents surveys from a workshop held during the theme year in geometry and topology at the Centre de recherches mathématiques (CRM, University of Montréal). The volume is in some sense a sequel to Mirror Symmetry I (1998) and Mirror Symmetry II (1996), copublished by the AMS and International Press. Included are recent developments in the theory of mirror manifolds and the related areas of complex and symplectic geometry. The long introductory articles explain the key physical ideas and motivation, namely conformal field theory, supersymmetry, and string theory. Open problems are emphasized. Thus the book provides an efficient way for a very broad audience of mathematicians and physicists to reach the frontier of research in this fast expanding area. - See more at: http://bookstore.ams.org/amsip-10#sthash.DbxEFJDx.dpuf

  9. Relativistic mirrors in laser plasmas (analytical methods)

    Science.gov (United States)

    Bulanov, S. V.; Esirkepov, T. Zh; Kando, M.; Koga, J.

    2016-10-01

    Relativistic flying mirrors in plasmas are realized as thin dense electron (or electron-ion) layers accelerated by high-intensity electromagnetic waves to velocities close to the speed of light in vacuum. The reflection of an electromagnetic wave from the relativistic mirror results in its energy and frequency changing. In a counter-propagation configuration, the frequency of the reflected wave is multiplied by the factor proportional to the Lorentz factor squared. This scientific area promises the development of sources of ultrashort x-ray pulses in the attosecond range. The expected intensity will reach the level at which the effects predicted by nonlinear quantum electrodynamics start to play a key role. We present an overview of theoretical methods used to describe relativistic flying, accelerating, oscillating mirrors emerging in intense laser-plasma interactions.

  10. Topological mirror insulators in one dimension

    Science.gov (United States)

    Lau, Alexander; van den Brink, Jeroen; Ortix, Carmine

    2016-10-01

    We demonstrate the existence of topological insulators in one dimension (1D) protected by mirror and time-reversal symmetries. They are characterized by a nontrivial Z2 topological invariant defined in terms of the "partial" polarizations, which we show to be quantized in the presence of a 1D mirror point. The topological invariant determines the generic presence or absence of integer boundary charges at the mirror-symmetric boundaries of the system. We check our findings against spin-orbit coupled Aubry-André-Harper models that can be realized, e.g., in cold-atomic Fermi gases loaded in one-dimensional optical lattices or in density- and Rashba spin-orbit-modulated semiconductor nanowires. In this setup, in-gap end-mode Kramers doublets appearing in the topologically nontrivial state effectively constitute a double-quantum dot with spin-orbit coupling.

  11. Optical Properties of Relativistic Plasma Mirrors

    CERN Document Server

    Vincenti, H; Kahaly, S; Martin, Ph; Quéré, F

    2013-01-01

    The advent of ultrahigh-power femtosecond lasers creates a need for optical components suitable to handle ultrahigh light intensities. Due to the unavoidable laser-induced ionization of matter, these components will have to be based on a plasma medium. An archetype of such optical elements is a plasma mirror, created when an intense femtosecond laser pulse impinges on a solid target. It consists of a dense plasma, formed by the laser field itself, which specularly reflects the main part of the pulse. Plasma mirrors have major potential applications as active optical elements to manipulate the temporal and spatial properties of intense laser beams, in particular for the generation of intense attosecond pulses of light. We investigate the basic physics involved in the deformation of a plasma mirror resulting from the light pressure exerted by the ultraintense laser during reflection, by deriving a simple model of this fundamental process, which we validate both numerically and experimentally. The understanding ...

  12. An advanced KB mirror pair for microfocusing

    CERN Document Server

    Ferme, J J

    2001-01-01

    A new range of micro-focusing mirrors based on KB pairs has been developed by SESO for Beamline Nanospectroscopy at the Elettra Storage Ring in Trieste, Italy. Both the focusing and the aspheric shape are adjustable with stepper motors. The goal of the beamline is to have a high photon density spot with a variable size in the experimental chamber over the whole soft X-ray range. The estimated dimension of the final spot should be smaller than 4 mu m sup 2 FWHM, with a photon density of the order of 10 sup 1 sup 3 photons/s mu m sup 2; this may be achieved only by accepting an angular divergence on these mirrors of between 5 and 10 mrad. This condition can be fulfilled only with elliptical (or plane elliptical) mirrors with very limited residual slope errors (below 1 mu rad RMS) that are able to correct even small focal distance errors.

  13. Mirror symmetry for two parameter models, 2

    CERN Document Server

    Candelas, Philip; Katz, S; Morrison, Douglas Robert Ogston; Philip Candelas; Anamaria Font; Sheldon Katz; David R Morrison

    1994-01-01

    We describe in detail the space of the two K\\"ahler parameters of the Calabi--Yau manifold \\P_4^{(1,1,1,6,9)}[18] by exploiting mirror symmetry. The large complex structure limit of the mirror, which corresponds to the classical large radius limit, is found by studying the monodromy of the periods about the discriminant locus, the boundary of the moduli space corresponding to singular Calabi--Yau manifolds. A symplectic basis of periods is found and the action of the Sp(6,\\Z) generators of the modular group is determined. From the mirror map we compute the instanton expansion of the Yukawa couplings and the generalized N=2 index, arriving at the numbers of instantons of genus zero and genus one of each degree. We also investigate an SL(2,\\Z) symmetry that acts on a boundary of the moduli space.

  14. Gasdynamic Mirror (GDM) Fusion Propulsion Engine Experiment

    Science.gov (United States)

    1999-01-01

    The Gasdynamic Mirror, or GDM, is an example of a magnetic mirror-based fusion propulsion system. Its design is primarily consisting of a long slender solenoid surrounding a vacuum chamber that contains plasma. The bulk of the fusion plasma is confined by magnetic field generated by a series of toroidal-shaped magnets in the center section of the device. the purpose of the GDM Fusion Propulsion Experiment is to confirm the feasibility of the concept and to demonstrate many of the operational characteristics of a full-size plasma can be confined within the desired physical configuration and still reman stable. This image shows an engineer from Propulsion Research Technologies Division at Marshall Space Flight Center inspecting solenoid magnets-A, an integrate part of the Gasdynamic Mirror Fusion Propulsion Engine Experiment.

  15. Chirped mirrors with low dispersion ripple.

    Science.gov (United States)

    Pervak, V; Naumov, S; Krausz, F; Apolonski, A

    2007-10-17

    We demonstrate a chirped dielectric multilayer mirror (CM) with controlled reflectivity and dispersion in the wavelength range 760-840 nm. It exhibits a reflectivity of >99.9% and a mean group delay dispersion (GDD) of about -30 fs(2) with a theoretical GDD ripple of less than 0.5 fs(2) in the working spectral range. Deviations of the measured GDD from the calculated one are restricted to less than +/- 3 fs(2), limited by our measurement system. Simulations reveal that a dispersive delay line composed of 120 bounces off these mirrors introduces negligible distortion to a femtosecond pulse and largely preserves its contrast. The mirrors constitute an ideal tool for precision intracavity or extracavity dispersion control in the range of several thousand fs(2), particularly if pulses with high contrast are to be generated.

  16. Computer Controlled Polishing of the Off-axis Aspheric Mirrors

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    In this paper, the manufacturing and testing procedures to make large off-axis aspherical mirrors are presented. The difficulties in polishing and testing for both circular-aperture and rectangular-aperture mirrors are previewed, and a possible solution is given. The two mirrors have been polished by means of CCOS, and the final accuracy is 25nm rms for 770mm×210mm rectangular mirror and 20nm rms for φ600mm circular mirror. These results just meet the optical tolerances specified by the designer, and the manufacturing and testing procedures presented here show good ability to make the large off-axis aspherical mirrors.

  17. Well baffled two-mirror corrector for a parabola.

    Science.gov (United States)

    Shafer, D R

    1977-05-01

    The two-mirror Baker corrector for a parabolic telescope mirror is a well-known, very elegant design. In some variations, both corrector mirrors are spherical. The only thing marring the beauty of this solution to providing anastigmatic performance for large parabolic telescope mirrors is that the system is difficult to baffle. An alternate two-mirror corrector is presented here-based on a different design principle-that is easy to baffle. One of the two corrector mirrors is spherical, and there is a field stop to further aid in baffling. The penalty paid is that the signs.

  18. Active Beam Shaping System and Method Using Sequential Deformable Mirrors

    Science.gov (United States)

    Norman, Colin A. (Inventor); Pueyo, Laurent A. (Inventor)

    2015-01-01

    An active optical beam shaping system includes a first deformable mirror arranged to at least partially intercept an entrance beam of light and to provide a first reflected beam of light, a second deformable mirror arranged to at least partially intercept the first reflected beam of light from the first deformable mirror and to provide a second reflected beam of light, and a signal processing and control system configured to communicate with the first and second deformable mirrors. The first deformable mirror, the second deformable mirror and the signal processing and control system together provide a large amplitude light modulation range to provide an actively shaped optical beam.

  19. Two-Sided Gravitational Mirror: Sealing off Curvature Singularities

    CERN Document Server

    Davidson, Aharon

    2012-01-01

    A gravitational mirror is a non-singular finite redshift surface which bounces all incident null geodesics. While a white mirror (outward bouncing) resembles 't Hooft's brick wall, a black mirror (inward bouncing) offers a novel mechanism for sealing off curvature singularities. The geometry underlying a two-sided mirror is characterized by a single signature change, to be contrasted with the signature flip which governs the black hole geometry. To demonstrate the phenomenon analytically, we derive an exact, static, radially symmetric, two-sided mirror solution, which asymptotes the massless BTZ black hole background, and then probe the local structure of a massive mirror.

  20. Alignment and focus of mirrored facets of a heliosat

    Energy Technology Data Exchange (ETDEWEB)

    Yellowhair, Julius E; Ho, Clifford Kuofei; Diver, Richard B; Moss, Timothy A

    2013-11-12

    Various technologies pertaining to aligning and focusing mirrored facets of a heliostat are described herein. Updating alignment and/or focus of mirrored facets is undertaken through generation of a theoretical image, wherein the theoretical image is indicative of a reflection of the target via the mirrored facets when the mirrored facets are properly aligned. This theoretical image includes reference points that are overlaid on an image of the target as reflected by the mirrored facets of the heliostat. A technician adjusts alignment/focus of a mirrored facet by causing reflected reference markings to become aligned with the reference points in the theoretical image.

  1. Mirroring Mobile Phone in the Clouds

    OpenAIRE

    Frank Z.Wang

    2014-01-01

    This paper presents a framework of Mirroring Mobile Phone in the Clouds (MMPC) to speed up data/computing intensive applications on a mobile phone by taking full advantage of the super computing power of the clouds. An application on the mobile phone is dynamically partitioned in such a way that the heavy-weighted part is always running on a mirrored server in the clouds while the light-weighted part remains on the mobile phone. A performance improvement (an energy consumption reduction of 70...

  2. Topology optimization design of space rectangular mirror

    Science.gov (United States)

    Qu, Yanjun; Wang, Wei; Liu, Bei; Li, Xupeng

    2016-10-01

    A conceptual lightweight rectangular mirror is designed based on the theory of topology optimization and the specific structure size is determined through sensitivity analysis and size optimization in this paper. Under the load condition of gravity along the optical axis, compared with the mirrors designed by traditional method using finite element analysis method, the performance of the topology optimization reflectors supported by peripheral six points are superior in lightweight ratio, structure stiffness and the reflective surface accuracy. This suggests that the lightweight method in this paper is effective and has potential value for the design of rectangular reflector.

  3. Relativistic Mirrors in Laser Plasmas (Analytical Methods)

    CERN Document Server

    Bulanov, Sergei V; Kando, Masaki; Koga, James K

    2016-01-01

    Relativistic flying mirrors in plasmas are realized as thin dense electron (or electron-ion) layers accelerated by high-intensity electromagnetic waves to velocities close to the speed of light in vacuum. The reflection of an electromagnetic wave from the relativistic mirror results in its energy and frequency changing. In a counter-propagation configuration, the frequency of the reflected wave is multiplied by the factor proportional to the Lorentz factor squared. This scientific area promises the development of sources of ultrashort X-ray pulses in the attosecond range. The expected intensity will reach the level at which the effects predicted by nonlinear quantum electrodynamics start to play a key role.

  4. The many faces of mirror symmetry

    CERN Document Server

    Kachru, Shamit; Torroba, Gonzalo; Wang, Huajia

    2016-01-01

    We study supersymmetry breaking perturbations of the simplest dual pair of 2+1-dimensional N = 2 supersymmetric field theories -- the free chiral multiplet and N = 2 super-QED with a single flavor. We find dual descriptions of a phase diagram containing four distinct massive phases. The equivalence of the intervening critical theories gives rise to several non-supersymmetric avatars of mirror symmetry: we find dualities relating scalar QED to a free fermion and Wilson-Fisher theories to both scalar and fermionic QED. Thus, mirror symmetry can be viewed as the multicritical parent duality from which these non-supersymmetric dualities directly descend.

  5. Black Hole - Moving Mirror II: Particle Creation

    CERN Document Server

    Good, Michael R R; Evans, Charles R

    2015-01-01

    There is an exact correspondence between the simplest solution to Einstein's equations describing the formation of a black hole and a particular moving mirror trajectory. In both cases the Bogolubov coefficients in 1+1 dimensions are identical and can be computed analytically. Particle creation is investigated by using wave packets. The entire particle creation history is computed, incorporating the early-time non-thermal emission due to the formation of the black hole (or the early-time acceleration of the moving mirror) and the evolution to a Planckian spectrum.

  6. Effects of a mirror-induced visual illusion on a reaching task in stroke patients: implications for mirror therapy training.

    Science.gov (United States)

    Selles, Ruud W; Michielsen, Marian E; Bussmann, Johannes B J; Stam, Henk J; Hurkmans, Henri L; Heijnen, Iris; de Groot, Danielle; Ribbers, Gerard M

    2014-09-01

    Although most mirror therapy studies have shown improved motor performance in stroke patients, the optimal mirror training protocol still remains unclear. To study the relative contribution of a mirror in training a reaching task and of unilateral and bimanual training with a mirror. A total of 93 stroke patients at least 6 months poststroke were instructed to perform a reaching task as fast and as fluently as possible. They performed 70 practice trials after being randomly allocated to 1 of 5 experimental groups: training with (1) the paretic arm with direct view (Paretic-No Mirror), (2) the nonparetic arm with direct view (Nonparetic-No Mirror), (3) the nonparetic arm with mirror reflection (Nonparetic Mirror), (4) both sides and with a nontransparent screen preventing visual control of paretic side (Bilateral-Screen), and (5) both sides with mirror reflection of the nonparetic arm (Bilateral-Mirror). As baseline and follow-up, patients performed 6 trials using only their paretic side. Primary outcome measure was the movement time. We found the largest intervention effect in the Paretic-No Mirror condition. However, the Nonparetic-Mirror condition was not significantly different from the Paretic-No Mirror condition, while the Unaffected-No Mirror condition had significantly less improvement than the Paretic-No Mirror condition. In addition, movement time improved significantly less in the bimanual conditions and there was no difference between both bimanual conditions or between both mirror conditions. The present study confirms that using a mirror reflection can facilitate motor learning. In this task, bimanual movement using mirror training was less effective than unilateral training. © The Author(s) 2014.

  7. [Mirror, mirror of the wall: mirror therapy in the treatment of phantom limbs and phantom limb pain].

    Science.gov (United States)

    Casale, Roberto; Furnari, Anna; Lamberti, Raul Coelho; Kouloulas, Efthimios; Hagenberg, Annegret; Mallik, Maryam

    2015-01-01

    Phantom limb and phantom limb pain control are pivotal points in the sequence of intervention to bring the amputee to functional autonomy. The alterations of perception and sensation, the pain of the residual limb and the phantom limb are therefore aspects of amputation that should be taken into account in the "prise en charge" of these patients. Within the more advanced physical therapies to control phantom and phantom limb pain there is the use of mirrors (mirror therapy). This article willfocus on its use and on the possible side effects induced by the lack of patient selection and a conflict of body schema restoration through mirror therapy with concurrent prosthetic training and trauma acceptance. Advice on the need to select patients before treatment decisions, with regard to their psychological as well as clinical profile (including time since amputation and clinical setting), and the need to be aware of the possible adverse effects matching different and somehow conflicting therapeutic approaches, are put forward. Thus a coordinated sequence of diagnostic, prognostic and therapeutic procedures carried out by an interdisciplinary rehabilitation team that works globally on all patients' problems is fundamental in the management of amputees and phantom limb pain. Further studies and the development of a multidisciplinary network to study this and other applications of mirror therapy are needed.

  8. Design, Construction, and Testing of Lightweight X-ray Mirror Modules

    Science.gov (United States)

    McClelland, Ryan S.; Biskach, Michael P.; Chan, Kai-Wing; Espina, Rebecca A.; Hohl, Bruce R.; Matson, Elizabeth A.; Saha, Timo C.; Zhang, William W.

    2013-01-01

    Lightweight and high resolution optics are needed for future space-based X-ray telescopes to achieve advances in high-energy astrophysics. The Next Generation X-ray Optics (NGXO) team at NASA GSFC is nearing mission readiness for a 10 arc-second Half Power Diameter (HPD) slumped glass mirror technology while laying the groundwork for a future 1-2 arc-second technology based on polished silicon mirrors. Technology Development Modules (TDMs) have been designed, fabricated, integrated with mirrors segments, and extensively tested to demonstrate technology readiness. Tests include X-ray performance, thermal vacuum, acoustic load, and random vibration. The thermal vacuum and acoustic load environments have proven relatively benign, while the random vibration environment has proven challenging due to large input amplification at frequencies above 500 Hz. Epoxy selection, surface preparation, and larger bond area have increased bond strength while vibration isolation has decreased vibration amplification allowing for space launch requirements to be met in the near term. The next generation of TDMs, which demonstrates a lightweight structure supporting more mirror segments, is currently being fabricated. Analysis predicts superior performance characteristics due to the use of E-60 Beryllium-Oxide Metal Matrix Composite material, with only a modest cost increase. These TDMs will be larger, lighter, stiffer, and stronger than the current generation. Preliminary steps are being taken to enable mounting and testing of 1-2 arc-second mirror segments expected to be available in the future. A Vertical X-ray Test Facility (VXTF) will minimize module gravity distortion and allow for less constrained mirror mounts, such as fully kinematic mounts. Permanent kinematic mounting into a modified TDM has been demonstrated to achieve 2 arc-second level distortion free alignment.

  9. Moving mirrors and the fluctuation-dissipation theorem

    CERN Document Server

    Stargen, D Jaffino; Sriramkumar, L

    2016-01-01

    We investigate the random motion of a mirror in (1 + 1)-dimensions that is immersed in a thermal bath of massless scalar particles which are interacting with the mirror through a boundary condition. Imposing the Dirichlet or the Neumann boundary conditions on the moving mirror, we evaluate the mean radiation reaction force on the mirror and the correlation function describing the fluctuations in the force about the mean value. From the correlation function thus obtained, we explicitly establish the fluctuation-dissipation theorem governing the moving mirror. Using the fluctuation-dissipation theorem, we compute the mean-squared displacement of the mirror at finite and zero temperature. We clarify a few points concerning the various limiting behavior of the mean-squared displacement of the mirror. While we recover the standard result at finite temperature, we find that the mirror diffuses logarithmically at zero temperature, confirming similar conclusions that have been arrived at earlier in this context. We a...

  10. Piezoelectric deformable mirror for intra-cavity laser adaptive optics.

    CSIR Research Space (South Africa)

    Long, CS

    2008-03-01

    Full Text Available This paper describes the development of a deformable mirror to be used in conjunction with diffractive optical elements inside a laser cavity. A prototype piezoelectric unimorph adaptive mirror was developed to correct for time dependent phase...

  11. The investigation on mirrors maladjustment for RLG

    Science.gov (United States)

    He, Xiao-qing; Gao, Ai-hua; Hu, Shang-bin; Lu, Zhi-guo

    2011-06-01

    In order to meet the high demand of the entire technology processing, the error compensation method is usually used to correct them and is premised on a good understanding of error sources and the law of the errors. In this paper, based on the theories of Collins's Integral and Collins's EIKONAL Function and the MATLAB software, we simulated and calculated the spatial distribution of optical beam in the cavity of the ring laser gyro under the resonator's maladjustment caused by the technology processing. From the simulation results, we can get that to the small-gain lasers, the same amount of disorders in the different structures have different effects on the spatial distribution of the beam, and the structures using the spherical mirrors relatively have the small impact on the beam; under the same disorder in the same cavity shape, the signal light and the calibration light which are respectively detected from the mirror M1 and M4 are different; under the same structures, different mirrors with the same amount of disorder will cause the different beat frequency difference; because of the disorders, the spot centers of clockwise and counterclockwise waves happen shift and will seriously affect the normal operation of the laser gyro if the imbalance reaches a certain degree. This work has a guiding role in the mirror adjustment of the laser gyros' technology processing, and has a reference value to the survival rate of the laser gyros and the improvement of measurement accuracy.

  12. The "Curriculum Vitae": An Imperfect Mirror.

    Science.gov (United States)

    Bennett, John B.

    1992-01-01

    Curriculum vitae for college faculty can be ambiguous and even misleading: they can obscure an individual's primary teaching and instructional achievements, tell less than they appear to, and convey an unintended message. Faculty should evaluate the clarity and force with which their vitae express their accomplishments and mirror their abilities.…

  13. Spheroidal galactic halos and mirror dark matter

    CERN Document Server

    Foot, R

    2004-01-01

    Mirror matter has been proposed as a dark matter candidate. It has several very attractive features, including automatic stability and darkness, the ability to mimic the broad features of cold dark matter while in the linear density perturbation regime, and consistency with all direct dark matter search experiments, both negative (e.g. CDMS II) and positive (DAMA). In this paper we consider an important unsolved problem: Are there plausible reasons to explain why most of the mirror matter in spiral galaxies exists in the form of gaseous {\\it spheroidal} galactic halos around ordinary matter {\\it disks}? We compute an order-of-magnitude estimate that the mirror photon luminosity of a typical spiral galaxy today is around $10^{44}$ erg/s. Interestingly, this rate of energy loss is similar to the power supplied by ordinary supernova explosions. We discuss circumstances under which supernova power can be used to heat the gaseous part of the mirror matter halo and hence prevent its collapse to a disk. The {\\it mac...

  14. Homological Perturbation Theory and Mirror Symmetry

    Institute of Scientific and Technical Information of China (English)

    Jian ZHOU

    2003-01-01

    We explain how deformation theories of geometric objects such as complex structures,Poisson structures and holomorphic bundle structures lead to differential Gerstenhaber or Poisson al-gebras. We use homological perturbation theory to construct A∞ algebra structures on the cohomology,and their canonically defined deformations. Such constructions are used to formulate a version of A∞algebraic mirror symmetry.

  15. Deformable Mirrors Capture Exoplanet Data, Reflect Lasers

    Science.gov (United States)

    2014-01-01

    To image and characterize exoplanets, Goddard Space Flight Center turned to deformable mirrors (DMs). Berkeley, California-based Iris AO, Inc. worked with Goddard through the SBIR program to improve the company’s microelectromechanical DMs, which are now being evaluated and used for biological research, industrial applications, and could even be used by drug manufacturers.

  16. Brane brick models in the mirror

    Science.gov (United States)

    Franco, Sebastián; Lee, Sangmin; Seong, Rak-Kyeong; Vafa, Cumrun

    2017-02-01

    Brane brick models are Type IIA brane configurations that encode the 2 d N=(0,2) gauge theories on the worldvolume of D1-branes probing toric Calabi-Yau 4-folds. We use mirror symmetry to improve our understanding of this correspondence and to provide a systematic approach for constructing brane brick models starting from geometry. The mirror configuration consists of D5-branes wrapping 4-spheres and the gauge theory is determined by how they intersect. We also explain how 2 d (0 , 2) triality is realized in terms of geometric transitions in the mirror geometry. Mirror symmetry leads to a geometric unification of dualities in different dimensions, where the order of duality is n - 1 for a Calabi-Yau n-fold. This makes us conjecture the existence of a quadrality symmetry in 0 d. Finally, we comment on how the M-theory lift of brane brick models connects to the classification of 2 d (0 , 2) theories in terms of 4-manifolds.

  17. Mirror Symmetry and Polar Duality of Polytopes

    Directory of Open Access Journals (Sweden)

    David A. Cox

    2015-09-01

    Full Text Available This expository article explores the connection between the polar duality from polyhedral geometry and mirror symmetry from mathematical physics and algebraic geometry. Topics discussed include duality of polytopes and cones as well as the famous quintic threefold and the toric variety of a reflexive polytope.

  18. Mirror Images: New Reflections on Teacher Leadership

    Science.gov (United States)

    Reason, Casey; Reason, Clair

    2011-01-01

    What inspires teachers to see themselves as leaders? "Mirror Images" takes a comprehensive look at what teacher leadership means today and how teachers can transform the future of their profession. Included are ten iconic images of teacher leadership roles to help teachers move beyond teaching as they were taught. The authors make a compelling…

  19. Mirror Neurons and the Evolution of Language

    Science.gov (United States)

    Corballis, Michael C.

    2010-01-01

    The mirror system provided a natural platform for the subsequent evolution of language. In nonhuman primates, the system provides for the understanding of biological action, and possibly for imitation, both prerequisites for language. I argue that language evolved from manual gestures, initially as a system of pantomime, but with gestures…

  20. Adjustable Membrane Mirrors Incorporating G-Elastomers

    Science.gov (United States)

    Chang, Zensheu; Morgan, Rhonda M.; Xu, Tian-Bing; Su, Ji; Hishinuma, Yoshikazu; Yang, Eui-Hyeok

    2008-01-01

    Lightweight, flexible, large-aperture mirrors of a type being developed for use in outer space have unimorph structures that enable precise adjustment of their surface figures. A mirror of this type includes a reflective membrane layer bonded with an electrostrictive grafted elastomer (G-elastomer) layer, plus electrodes suitably positioned with respect to these layers. By virtue of the electrostrictive effect, an electric field applied to the G-elastomer membrane induces a strain along the membrane and thus causes a deflection of the mirror surface. Utilizing this effect, the mirror surface figure can be adjusted locally by individually addressing pairs of electrodes. G-elastomers, which were developed at NASA Langley Research Center, were chosen for this development in preference to other electroactive polymers partly because they offer superior electromechanical performance. Whereas other electroactive polymers offer, variously, large strains with low moduli of elasticity or small strains with high moduli of elasticity, G-elastomers offer both large strains (as large as 4 percent) and high moduli of elasticity (about 580 MPa). In addition, G-elastomer layers can be made by standard melt pressing or room-temperature solution casting.

  1. Brane Brick Models in the Mirror

    CERN Document Server

    Franco, Sebastian; Seong, Rak-Kyeong; Vafa, Cumrun

    2016-01-01

    Brane brick models are Type IIA brane configurations that encode the $2d$ $\\mathcal{N}=(0,2)$ gauge theories on the worldvolume of D1-branes probing toric Calabi-Yau 4-folds. We use mirror symmetry to improve our understanding of this correspondence and to provide a systematic approach for constructing brane brick models starting from geometry. The mirror configuration consists of D5-branes wrapping 4-spheres and the gauge theory is determined by how they intersect. We also explain how $2d$ $(0,2)$ triality is realized in terms of geometric transitions in the mirror geometry. Mirror symmetry leads to a geometric unification of dualities in different dimensions, where the order of duality is $n-1$ for a Calabi-Yau $n$-fold. This makes us conjecture the existence of a quadrality symmetry in $0d$. Finally, we comment on how the M-theory lift of brane brick models connects to the classification of $2d$ $(0,2)$ theories in terms of 4-manifolds.

  2. Children's Drawings: A Mirror to Their Minds

    Science.gov (United States)

    Cherney, Isabelle D.; Seiwert, Clair S.; Dickey, Tara M.; Flichtbeil, Judith D.

    2006-01-01

    Children's drawings are thought to be a mirror of a child's representational development. Research suggests that with age children develop more complex and symbolic representational strategies and reference points become more differentiated by gender. We collected two drawings from 109 5-13-year-old children (three age groups). Each child drew…

  3. Neuro-Fuzzy Phasing of Segmented Mirrors

    Science.gov (United States)

    Olivier, Philip D.

    1999-01-01

    A new phasing algorithm for segmented mirrors based on neuro-fuzzy techniques is described. A unique feature of this algorithm is the introduction of an observer bank. Its effectiveness is tested in a very simple model with remarkable success. The new algorithm requires much less computational effort than existing algorithms and therefore promises to be quite useful when implemented on more complex models.

  4. Solid State Replacement of Rotating Mirror Cameras

    Energy Technology Data Exchange (ETDEWEB)

    Frank, A M; Bartolick, J M

    2006-08-25

    Rotating mirror cameras have been the mainstay of mega-frame per second imaging for decades. There is still no electronic camera that can match a film based rotary mirror camera for the combination of frame count, speed, resolution and dynamic range. The rotary mirror cameras are predominantly used in the range of 0.1 to 100 micro-seconds per frame, for 25 to more than a hundred frames. Electron tube gated cameras dominate the sub microsecond regime but are frame count limited. Video cameras are pushing into the microsecond regime but are resolution limited by the high data rates. An all solid state architecture, dubbed ''In-situ Storage Image Sensor'' or ''ISIS'', by Prof. Goji Etoh, has made its first appearance into the market and its evaluation is discussed. Recent work at Lawrence Livermore National Laboratory has concentrated both on evaluation of the presently available technologies and exploring the capabilities of the ISIS architecture. It is clear though there is presently no single chip camera that can simultaneously match the rotary mirror cameras, the ISIS architecture has the potential to approach their performance.

  5. Mirror Neurons and the Evolution of Language

    Science.gov (United States)

    Corballis, Michael C.

    2010-01-01

    The mirror system provided a natural platform for the subsequent evolution of language. In nonhuman primates, the system provides for the understanding of biological action, and possibly for imitation, both prerequisites for language. I argue that language evolved from manual gestures, initially as a system of pantomime, but with gestures…

  6. Mirror Your Audience's Attitude: A Global Profile.

    Science.gov (United States)

    Meussling, Vonne

    Recent advertising research has suggested that to gain initial entry into and retain continual success with a targeted audience of consumers, it is wise to mirror the attitudes and desires of those consumers. This has proven effective in the United States, where companies such as Chevrolet, Levi Strauss, and Coca-Cola have successfully catered to…

  7. Social neuroscience: mirror neurons recorded in humans.

    Science.gov (United States)

    Keysers, Christian; Gazzola, Valeria

    2010-04-27

    New single-cell recordings show that humans do have mirror neurons, and in more brain regions than previously suspected. Some action-execution neurons were seen to be inhibited during observation, possibly preventing imitation and helping self/other discrimination.

  8. Silicon Carbide Technologies for Lightweighted Aerospace Mirrors

    Science.gov (United States)

    2008-09-01

    silicon carbide (SiC) based materials. It is anticipated that SiC can be utilized for most applications from cryogenic to high temperatures. This talk will focus on describing the SOA for these (near term) SiC technology solutions for making mirror structural substrates, figuring and finishing technologies being investigated to reduce cost time

  9. Analysis of Online Composite Mirror Descent Algorithm.

    Science.gov (United States)

    Lei, Yunwen; Zhou, Ding-Xuan

    2017-03-01

    We study the convergence of the online composite mirror descent algorithm, which involves a mirror map to reflect the geometry of the data and a convex objective function consisting of a loss and a regularizer possibly inducing sparsity. Our error analysis provides convergence rates in terms of properties of the strongly convex differentiable mirror map and the objective function. For a class of objective functions with Hölder continuous gradients, the convergence rates of the excess (regularized) risk under polynomially decaying step sizes have the order [Formula: see text] after [Formula: see text] iterates. Our results improve the existing error analysis for the online composite mirror descent algorithm by avoiding averaging and removing boundedness assumptions, and they sharpen the existing convergence rates of the last iterate for online gradient descent without any boundedness assumptions. Our methodology mainly depends on a novel error decomposition in terms of an excess Bregman distance, refined analysis of self-bounding properties of the objective function, and the resulting one-step progress bounds.

  10. Large Telescope Segmented Primary Mirror Alignment

    Science.gov (United States)

    Rud, Mayer

    2010-01-01

    A document discusses a broadband (white light) point source, located at the telescope Cassegrain focus, which generates a cone of light limited by the hole in the secondary mirror (SM). It propagates to the aspheric null-mirror, which is optimized to make all the reflected rays to be normal to the primary mirror (PM) upon reflection. PM retro-reflects the rays back through the system for wavefront analysis. The point source and the wavefront analysis subsystems are all located behind the PM. The PM phasing is absolute (white light) and does not involve the SM. A relatively small, aspheric null-mirror located near the PM center of curvature has been designed to deliver the high level of optical wavefront correction. The phasing of the segments is absolute due to the use of a broadband source. The segmented PM is optically aligned independently and separately from the SM alignment. The separation of the PM segments alignment from the PM to the SM, and other telescope optics alignments, may be a significant advantage, eliminating the errors coupling. The point source of this concept is fully cooperative, unlike a star or laser-generated guide-star, providing the necessary brightness for the optimal S/N ratio, the spectral content, and the stable on-axis position. This concept can be implemented in the lab for the PM initial alignment, or made to be a permanent feature of the space-based or groundbased telescope.

  11. Alignment and Integration of Lightweight Mirror Segments

    Science.gov (United States)

    Evans, Tyler; Biskach, Michael; Mazzarella, Jim; McClelland, Ryan; Saha, Timo; Zhang, Will; Chan, Kai-Wing

    2011-01-01

    The optics for the International X-Ray Observatory (IXO) require alignment and integration of about fourteen thousand thin mirror segments to achieve the mission goal of 3.0 square meters of effective area at 1.25 keV with an angular resolution of five arc-seconds. These mirror segments are 0.4 mm thick, and 200 to 400 mm in size, which makes it difficult not to impart distortion at the sub-arc-second level. This paper outlines the precise alignment, permanent bonding, and verification testing techniques developed at NASA's Goddard Space Flight Center (GSFC). Improvements in alignment include new hardware and automation software. Improvements in bonding include two module new simulators to bond mirrors into, a glass housing for proving single pair bonding, and a Kovar module for bonding multiple pairs of mirrors. Three separate bonding trials were x-ray tested producing results meeting the requirement of sub ten arc-second alignment. This paper will highlight these recent advances in alignment, testing, and bonding techniques and the exciting developments in thin x-ray optic technology development.

  12. Mirror Symmetry of Matter and Antimatter

    Science.gov (United States)

    Close, Robert

    2010-03-01

    Physical processes involving weak interactions have mirror images which can be mimicked in the natural universe only by exchanging matter and antimatter. This experimental observation is easily explained by the hypothesis that spatial inversion exchanges matter and antimatter. Yet according to conventional theory, the parity operator P does not exchange matter and antimatter but instead yields phenomena which have never been observed. We examine the conventional derivation of the Dirac parity operator and find that it is based on the speculative assumption that the unit imaginary is always a true scalar rather than a pseudoscalar. This assumption incorrectly requires that the matrix 0̂ preserve its sign under spatial inversion. This requirement results in a mixed-parity vector space defined relative to velocity, which is otherwise isomorphic to the spatial axes. We derive a new spatial inversion operator M (for mirroring) by requiring that for any set of orthogonal basis vectors, all three must have the same parity. A pseudoscalar unit imaginary is defined in terms of Dirac matrices. The M operator is a symmetry of the Dirac equation. It exchanges positive and negative energy eigenfunctions, consistent with all experimental evidence of mirror symmetry between matter and antimatter. This result provides a simple reason for the apparent absence in nature of mirror-like phenomena, such as right-handed neutrinos, which do not exchange matter and antimatter.

  13. Enhancing Learning Outcomes: The Internet Mirror Model

    Science.gov (United States)

    Stephenson, Robert S.

    2004-01-01

    The author redesigned an undergraduate physiology course using a novel Internet mirror model: parallel lecture and Internet-based sections conducted so that students can move freely from one to the other (or choose both) during the semester. Within the constraints of this paradigm, he used technology to enhance student learning: adding…

  14. Classroom Explorations: Pendulums, Mirrors, and Galileo's Drama

    Science.gov (United States)

    Cavicchi, Elizabeth

    2011-01-01

    What do you see in a mirror when not looking at yourself? What goes on as a pendulum swings? Undergraduates in a science class supposed that these behaviors were obvious until their explorations exposed questions with no quick answers. While exploring materials, students researched Galileo, his trial, and its aftermath. Galileo came to life both…

  15. Wavefront Reconstruction and Mirror Surface Optimizationfor Adaptive Optics

    Science.gov (United States)

    2014-06-01

    correction. A DM has a reflective surface with actuators along the back struc- ture that apply forces causing the mirror surface to adapt to a desired shape...actuators. The actuators cause forces along the back of the mirror structure and the mirror surface deflects to form the conjugate shape of the wavefront...optical axis of the primary mirror. The interferometer and null corrector are mounted to remove the 81 Interferometer Null corrector Hexapod ❋✐❣✉r

  16. Two-Sided Gravitational Mirror: Sealing off Curvature Singularities

    OpenAIRE

    Davidson, Aharon; Yellin, Ben

    2011-01-01

    A gravitational mirror is a non-singular finite redshift surface which bounces all incident null geodesics. While a white mirror (outward bouncing) resembles 't Hooft's brick wall, a black mirror (inward bouncing) offers a novel mechanism for sealing off curvature singularities. The geometry underlying a two-sided mirror is characterized by a single signature change, to be contrasted with the signature flip which governs the black hole geometry. To demonstrate the phenomenon analytically, we ...

  17. Efficacy of Mirror Therapy Containing Functional Tasks in Poststroke Patients

    OpenAIRE

    Lim, Kil-Byung; Lee, Hong-Jae; Yoo, JeeHyun; Yun, Hyun-Ju; Hwang, Hye-Jung

    2016-01-01

    Objective To investigate the effect of mirror therapy containing functional tasks on upper extremity function and activities of daily living in patients with subacute stroke. Methods The subjects were randomly divided into two groups: the mirror therapy group (30 patients) and the sham therapy group (30 patients). The mirror therapy group underwent a mirror therapy program together with conventional therapy for 20 minutes per day on 5 days per week for 4 weeks. The control group received a sh...

  18. Mirror Symmetry, D-Branes and Counting Holomorphic Discs

    OpenAIRE

    Aganagic, Mina; Vafa, Cumrun

    2000-01-01

    We consider a class of special Lagrangian subspaces of Calabi-Yau manifolds and identify their mirrors, using the recent derivation of mirror symmetry, as certain holomorphic varieties of the mirror geometry. This transforms the counting of holomorphic disc instantons ending on the Lagrangian submanifold to the classical Abel-Jacobi map on the mirror. We recover some results already anticipated as well as obtain some highly non-trivial new predictions.

  19. Characterization of a piezo bendable X-ray mirror.

    Science.gov (United States)

    Vannoni, Maurizio; Freijo Martín, Idoia; Siewert, Frank; Signorato, Riccardo; Yang, Fan; Sinn, Harald

    2016-01-01

    A full-scale piezo bendable mirror built as a prototype for an offset mirror at the European XFEL is characterized. The piezo ceramic elements are glued onto the mirror substrate, side-face on with respect to the reflecting surface. Using a nanometre optical component measuring machine and a large-aperture Fizeau interferometer, the mirror profile and influence functions were characterized, and further analysis was made to investigate the junction effect, hysteresis, twisting and reproducibility.

  20. Treatment Strategies for Intracranial Mirror Aneurysms.

    Science.gov (United States)

    Wang, Wen-Xin; Xue, Zhe; Li, Lin; Wu, Chen; Zhang, Yan-Yang; Lou, Xin; Ma, Lin; Sun, Zheng-Hui

    2017-04-01

    Intracranial mirror aneurysms are clinically rare and uncommonly reported in the literature. Therefore, the present study evaluated a series of mirror aneurysm cases with respect to the clinical features of the patients and the treatment strategies that were used. This study retrospectively reviewed and systematically analyzed the clinical features, imaging data, treatment methods, and treatment outcomes of 68 cases of mirror aneurysms (a total of 70 pairs) in patients who were admitted to our department between November 2007 and May 2016. The patient population included 24 male and 44 female patients, with a mean age of 52 years. The mirror aneurysms were primarily located in posterior communicating artery and middle cerebral artery and 65 of the aneurysms were large or giant (≧10 mm). Of the 68 patients, 28 were treated by the clipping or embolization of all aneurysms in one stage, 16 were treated in 2 stages, 16 were treated by treating part of the aneurysms, and 8 were observed. The modified Rankin Scale scores of the 60 patients that were treated indicated that 52 had a good recovery (modified Rankin Scale score ≦2; 86.7%), and 1 patient died. Treatment strategies for mirror aneurysms should be determined individually according to the location, size, and morphology of the aneurysm, as well as the clinical manifestations of each patient. Furthermore, the responsible ruptured aneurysm should be given treatment priority, whereas the contralateral unruptured aneurysm should be observed or treated in either 1 or 2 stages. Copyright © 2017 Elsevier Inc. All rights reserved.

  1. Next Generation Lightweight Mirror Modeling Software

    Science.gov (United States)

    Arnold, William R., Sr.; Fitzgerald, Mathew; Rosa, Rubin Jaca; Stahl, H. Philip

    2013-01-01

    The advances in manufacturing techniques for lightweight mirrors, such as EXELSIS deep core low temperature fusion, Corning's continued improvements in the Frit bonding process and the ability to cast large complex designs, combined with water-jet and conventional diamond machining of glasses and ceramics has created the need for more efficient means of generating finite element models of these structures. Traditional methods of assembling 400,000 + element models can take weeks of effort, severely limiting the range of possible optimization variables. This paper will introduce model generation software developed under NASA sponsorship for the design of both terrestrial and space based mirrors. The software deals with any current mirror manufacturing technique, single substrates, multiple arrays of substrates, as well as the ability to merge submodels into a single large model. The modeler generates both mirror and suspension system elements, suspensions can be created either for each individual petal or the whole mirror. A typical model generation of 250,000 nodes and 450,000 elements only takes 5-10 minutes, much of that time being variable input time. The program can create input decks for ANSYS, ABAQUS and NASTRAN. An archive/retrieval system permits creation of complete trade studies, varying cell size, depth, and petal size, suspension geometry with the ability to recall a particular set of parameters and make small or large changes with ease. The input decks created by the modeler are text files which can be modified by any editor, all the key shell thickness parameters are accessible and comments in deck identify which groups of elements are associated with these parameters. This again makes optimization easier. With ANSYS decks, the nodes representing support attachments are grouped into components; in ABAQUS these are SETS and in NASTRAN as GRIDPOINT SETS, this make integration of these models into large telescope or satellite models easier.

  2. Next-Generation Lightweight Mirror Modeling Software

    Science.gov (United States)

    Arnold, William R., Sr.; Fitzgerald, Mathew; Rosa, Rubin Jaca; Stahl, Phil

    2013-01-01

    The advances in manufacturing techniques for lightweight mirrors, such as EXELSIS deep core low temperature fusion, Corning's continued improvements in the Frit bonding process and the ability to cast large complex designs, combined with water-jet and conventional diamond machining of glasses and ceramics has created the need for more efficient means of generating finite element models of these structures. Traditional methods of assembling 400,000 + element models can take weeks of effort, severely limiting the range of possible optimization variables. This paper will introduce model generation software developed under NASA sponsorship for the design of both terrestrial and space based mirrors. The software deals with any current mirror manufacturing technique, single substrates, multiple arrays of substrates, as well as the ability to merge submodels into a single large model. The modeler generates both mirror and suspension system elements, suspensions can be created either for each individual petal or the whole mirror. A typical model generation of 250,000 nodes and 450,000 elements only takes 5-10 minutes, much of that time being variable input time. The program can create input decks for ANSYS, ABAQUS and NASTRAN. An archive/retrieval system permits creation of complete trade studies, varying cell size, depth, and petal size, suspension geometry with the ability to recall a particular set of parameters and make small or large changes with ease. The input decks created by the modeler are text files which can be modified by any editor, all the key shell thickness parameters are accessible and comments in deck identify which groups of elements are associated with these parameters. This again makes optimization easier. With ANSYS decks, the nodes representing support attachments are grouped into components; in ABAQUS these are SETS and in NASTRAN as GRIDPOINT SETS, this make integration of these models into large telescope or satellite models possible

  3. Improved Mirror Source Method in Roomacoustics

    Science.gov (United States)

    Mechel, F. P.

    2002-10-01

    Most authors in room acoustics qualify the mirror source method (MS-method) as the only exact method to evaluate sound fields in auditoria. But evidently nobody applies it. The reason for this discrepancy is the abundantly high numbers of needed mirror sources which are reported in the literature, although such estimations of needed numbers of mirror sources mostly are used for the justification of more or less heuristic modifications of the MS-method. The present, intentionally tutorial article accentuates the analytical foundations of the MS-method whereby the number of needed mirror sources is reduced already. Further, the task of field evaluation in three-dimensional spaces is reduced to a sequence of tasks in two-dimensional room edges. This not only allows the use of easier geometrical computations in two dimensions, but also the sound field in corner areas can be represented by a single (directional) source sitting on the corner line, so that only this "corner source" must be mirror-reflected in the further process. This procedure gives a drastic reduction of the number of needed equivalent sources. Finally, the traditional MS-method is not applicable in rooms with convex corners (the angle between the corner flanks, measured on the room side, exceeds 180°). In such cases, the MS-method is combined below with the second principle of superposition(PSP). It reduces the scattering task at convex corners to two sub-tasks between one flank and the median plane of the room wedge, i.e., always in concave corner areas where the MS-method can be applied.

  4. Profile measurement of concave spherical mirror and a flat mirror using a high-speed nanoprofiler.

    Science.gov (United States)

    Usuki, Koji; Kitayama, Takao; Matsumura, Hiroki; Kojima, Takuya; Uchikoshi, Junichi; Higashi, Yasuo; Endo, Katsuyoshi

    2013-05-16

    Ultraprecise aspheric mirrors that offer nanofocusing and high coherence are indispensable for developing third-generation synchrotron radiation and X-ray free-electron laser sources. In industry, the extreme ultraviolet (wavelength: 13.5 nm) lithography used for high-accuracy aspheric mirrors is a promising technology for fabricating semiconductor devices. In addition, ultraprecise mirrors with a radius of curvature of less than 10 mm are needed in many digital video instruments. We developed a new type of nanoprofiler that traces the normal vector of a mirror's surface. The principle of our measuring method is that the normal vector at each point on the surface is determined by making the incident light beam on the mirror surface and the reflected beam at that point coincide, using two sets of two pairs of goniometers and one linear stage. From the acquired normal vectors and their coordinates, the three-dimensional shape is calculated by a reconstruction algorithm. The characteristics of the measuring method are as follows: the profiler uses the straightness of laser light without using a reference surface. Surfaces of any shape can be measured, and there is no limit on the aperture size. We calibrated this nanoprofiler by considering the system error resulting from the assembly error and encoder scale error, and evaluated the performance at the nanometer scale. We suppressed the effect of random errors by maintaining the temperature in a constant-temperature room within ±0.01°C. We measured a concave spherical mirror with a radius of curvature of 400 mm and a flat mirror and compared the results with those obtained using a Fizeau interferometer. The profiles of the mirrors were consistent within the range of system errors.

  5. Technology and applications of micromachined silicon adaptive mirrors

    NARCIS (Netherlands)

    Vdovin, G.; Middelhoek, S.; Sarro, P.M.

    1997-01-01

    The technology of low-cost high-quality micromachined adaptive mirrors is reported. Adaptive mirrors are fabricated by combining bulk silicon micromachining with standard electronics technologies. Mirrors with tens of control channels, having RMS initial deviation from plane of the order of λ/20 and

  6. Titanium Alloy Strong Back for IXO Mirror Segments

    Science.gov (United States)

    Byron, Glenn P.; Kai-Wang, Chan

    2011-01-01

    A titanium-alloy mirror-holding fixture called a strong back allows the temporary and permanent bonding of a 50 degree D263 glass x-ray mirror (IXO here stands for International X-ray Observatory). The strong back is used to hold and position a mirror segment so that mounting tabs may be bonded to the mirror with ultra-low distortion of the optical surface. Ti-15%Mo alloy was the material of choice for the strong back and tabs because the coefficient of thermal expansion closely matches that of the D263 glass and the material is relatively easy to machine. This invention has the ability to transfer bonded mounting points from a temporary location on the strong back to a permanent location on the strong back with minimal distortion. Secondly, it converts a single mirror segment into a rigid body with an acceptable amount of distortion of the mirror, and then maneuvers that rigid body into optical alignment such that the mirror segment can be bonded into a housing simulator or mirror module. Key problems are that the mirrors are 0.4-mm thick and have a very low coefficient of thermal expansion (CTE). Because the mirrors are so thin, they are very flexible and are easily distorted. When permanently bonding the mirror, the goal is to achieve a less than 1-micron distortion. Temperature deviations in the lab, which have been measured to be around 1 C, have caused significant distortions in the mirror segment.

  7. Monitoring of absolute mirror alignment at COMPASS RICH-1 detector

    NARCIS (Netherlands)

    Alexeev, M.; Birsa, R.; Bradamante, F.; Bressan, A.; Chiosso, M.; Ciliberti, P.; Dalla Torre, S.; Denisov, O.; Duic, V.; Ferrero, A.; Finger, M.; Finger, M.; Gayde, J. Ch; Giorgi, M.; Gobbo, B.; Levorato, S.; Maggiora, A.; Martin, A.; Menon, G.; Panzieri, D.; Pesaro, G.; Polak, J.; Rocco, E.; Sbrizzai, G.; Schiavon, P.; Slunecka, M.; Sozzi, F.; Steiger, L.; Sulc, M.; Takekawa, S.; Tessarotto, F.

    2014-01-01

    The gaseous COMPASS RICH-1 detector uses two spherical mirror surfaces, segmented into 116 individual mirrors, to focus the Cherenkov photons onto the detector plane. Any mirror misalignment directly affects the detector resolution. The on-line Continuous Line Alignment and Monitoring (CLAM) photogr

  8. Demonstrating Chirality: Using a Mirror with Physical Models To Show Non-superimposability of Chiral Molecules with Their Mirror Images.

    Science.gov (United States)

    Collins, Michael J.

    2001-01-01

    Presents a remarkable demonstration on chiralty in molecules and the existence of enantiomers, also known as non-superimposable mirror images. Uses a mirror, a physical model of a molecule, and a bit of trickery involving the non-superimposable mirror image. (Author/NB)

  9. Axisymmetric Magnetic Mirror Fusion-Fission Hybrid

    Energy Technology Data Exchange (ETDEWEB)

    Moir, R. W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Martovetsky, N. N. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Molvik, A. W. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ryutov, D. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Simonen, T. C. [Univ. of California, Berkeley, CA (United States)

    2011-05-13

    The achieved performance of the gas dynamic trap version of magnetic mirrors and today’s technology we believe are sufficient with modest further efforts for a neutron source for material testing (Q=Pfusion/Pinput~0.1). The performance needed for commercial power production requires considerable further advances to achieve the necessary high Q>>10. An early application of the mirror, requiring intermediate performance and intermediate values of Q~1 are the hybrid applications. The Axisymmetric Mirror has a number of attractive features as a driver for a fusion-fission hybrid system: geometrical simplicity, inherently steady-state operation, and the presence of the natural divertors in the form of end tanks. This level of physics performance has the virtue of low risk and only modest R&D needed and its simplicity promises economy advantages. Operation at Q~1 allows for relatively low electron temperatures, in the range of 4 keV, for the DT injection energy ~ 80 keV. A simple mirror with the plasma diameter of 1 m and mirror-to-mirror length of 35 m is discussed. Simple circular superconducting coils are based on today’s technology. The positive ion neutral beams are similar to existing units but designed for steady state. A brief qualitative discussion of three groups of physics issues is presented: axial heat loss, MHD stability in the axisymmetric geometry, microstability of sloshing ions. Burning fission reactor wastes by fissioning actinides (transuranics: Pu, Np, Am, Cm, .. or just minor actinides: Np, Am, Cm, …) in the hybrid will multiply fusion’s energy by a factor of ~10 or more and diminish the Q needed to less than 1 to overcome the cost of recirculating power for good economics. The economic value of destroying actinides by fissioning is rather low based on either the cost of long-term storage or even deep geologic disposal so most of the revenues of hybrids will come from electrical power. Hybrids that obtain revenues from

  10. Mirror symmetry in the presence of branes

    Energy Technology Data Exchange (ETDEWEB)

    Mertens, Adrian

    2011-10-11

    This work deals with mirror symmetry for N=1 compactifications on compact Calabi-Yau threefolds with branes. The mayor tool is a combined deformation space for the Calabi-Yau and a hypersurface within it. Periods of this deformation space contain information about B-type branes within the hypersurface in addition to the usual closed string data. To study these periods we generalize techniques used in closed string mirror symmetry. We derive the Picard-Fuchs system and encode the information in extended toric polytopes. Solutions of the Picard-Fuchs equations give superpotentials for certain brane configurations. This is an efficient way to calculate superpotentials. The deformations we consider are massive for all branes with non trivial superpotential. Depending on a choice of a family of hypersurfaces, the superpotential of the effective low energy theory depends on different massive fields. A priori there is no reason for these fields to be lighter then other fields that are not included. We find however examples where the superpotential is nearly at. In these examples we use the Gauss-Manin connection on the combined deformation space to define an open string mirror map. We find instanton generated superpotentials of A-type branes. This gives predictions for Ooguri-Vafa invariants counting holomorphic disks that end on a Lagrangian brane on the Quintic. A second class of examples does not have preferred nearly massless deformations and different families of hypersurfaces can be used to calculate the same on-shell superpotential. We calculate examples of superpotentials for branes in Calabi-Yau manifolds with several moduli. The on-shell superpotentials are mapped to the mirror A-model to study the instanton expansion and to obtain predictions for disk invariants. The combined deformation spaces are equivalent to the quantum corrected Kaehler deformation spaces of certain non compact Calabi-Yau fourfolds. These fourfolds are fibrations of Calabi-Yau threefolds

  11. Quality evaluation of spaceborne SiC mirrors (I): analytical examination of the effects on mirror accuracy by variation in the thermal expansion property of the mirror surface.

    Science.gov (United States)

    Kotani, Masaki; Imai, Tadashi; Katayama, Haruyoshi; Yui, Yukari; Tange, Yoshio; Kaneda, Hidehiro; Nakagawa, Takao; Enya, Keigo

    2013-07-10

    The Japan Aerospace Exploration Agency has studied a large-scale lightweight mirror constructed of reaction-bonded silicon carbide-based material as a key technology in future astronomical and earth observation missions. The authors selected silicon carbide as the promising candidate due to excellent characteristics of specific stiffness and thermal stability. One of the most important technical issues for large-scale ceramic components is the uniformity of the material's property, depending on part and processing. It might influence mirror accuracy due to uneven thermal deformation. The authors conducted systematic case studies for the conditions of CTE by finite element analysis to know the typical influence of material property nonuniformity on mirror accuracy and consequently derived a comprehensive empirical equation for the series of CTE's main factors. In addition, the authors computationally reproduced the mirror accuracy profile of a small prototype mirror shown in cryogenic testing and hereby verified wide-range practical computational evaluation technology of mirror accuracy.

  12. The lightweight structure design of a CFRP mirror

    Science.gov (United States)

    Ding, Jiaoteng; Xu, Liang; Ma, Zhen; Xie, Yongjie; Luo, Yao; Wang, Yongjie; Pang, Zhihai

    2016-10-01

    The advantage of Carbon Fiber Reinforced Polymer (CFRP) is obvious as a common space material for low density, low thermal expansion coefficient and high specific stiffness characteristics, it is the ideal material choice for space optical reflector. Mirror structure with honeycomb can achieve high rates of lightweight, as well as high specific stiffness. For Φ300mm CFRP mirror, accounting of the actual process properties of CFRP, mirror panels laminated based on thermal stability design, honeycomb fabricated using one innovative inlaying-grafting design method. Finally, lightweight structure design of the CFRP primary mirror completed, the thermal stability result of the Φ300mm CFRP mirror achieved is 10nm°C.

  13. Light-weight spherical mirrors for Cherenkov detectors

    CERN Document Server

    Cisbani, E; Colilli, S; Crateri, R; Cusanno, F; De Leo, R; Fratoni, R; Frullani, S; Garibaldi, F; Giuliani, F; Gricia, M; Iodice, M; Iommi, R; Lagamba, L; Lucentini, M; Mostarda, A; Nappi, E; Pierangeli, L; Santavenere, F; Urciuoli, G M; Vernin, P

    2003-01-01

    Light-weight spherical mirrors have been appositely designed and built for the gas threshold Cherenkov detectors of the two Hall A spectrometers. The mirrors are made of a 1 mm thick aluminized plexiglass sheet, reinforced by a rigid backing consisting of a phenolic honeycomb sandwiched between two carbon fiber mats epoxy glued. The produced mirrors have a thickness equivalent to 0.55% of radiation length, and an optical slope error of about 5.5 mrad. These characteristics make these mirrors suitable for the implementation in Cherenkov threshold detectors. Ways to improve the mirror features are also discussed in view of their possible employment in RICH detectors.

  14. Simultaneous imaging/reflectivity measurements to assess diagnostic mirror cleaninga)

    Science.gov (United States)

    Skinner, C. H.; Gentile, C. A.; Doerner, R.

    2012-10-01

    Practical methods to clean ITER's diagnostic mirrors and restore reflectivity will be critical to ITER's plasma operations. We describe a technique to assess the efficacy of mirror cleaning techniques and detect any damage to the mirror surface. The method combines microscopic imaging and reflectivity measurements in the red, green, and blue spectral regions and at selected wavelengths. The method has been applied to laser cleaning of single crystal molybdenum mirrors coated with either carbon or beryllium films 150-420 nm thick. It is suitable for hazardous materials such as beryllium as the mirrors remain sealed in a vacuum chamber.

  15. Simultaneous imaging/reflectivity measurements to assess diagnostic mirror cleaning.

    Science.gov (United States)

    Skinner, C H; Gentile, C A; Doerner, R

    2012-10-01

    Practical methods to clean ITER's diagnostic mirrors and restore reflectivity will be critical to ITER's plasma operations. We describe a technique to assess the efficacy of mirror cleaning techniques and detect any damage to the mirror surface. The method combines microscopic imaging and reflectivity measurements in the red, green, and blue spectral regions and at selected wavelengths. The method has been applied to laser cleaning of single crystal molybdenum mirrors coated with either carbon or beryllium films 150-420 nm thick. It is suitable for hazardous materials such as beryllium as the mirrors remain sealed in a vacuum chamber.

  16. Incident angle-tuned, broadband, ultrahigh-sensitivity plasmonic antennas prepared from nanoparticles on imprinted mirrors.

    Science.gov (United States)

    Yu, Chen-Chieh; Tseng, Yi-Chuan; Su, Pao-Yun; Lin, Keng-Te; Shao, Chang-Ching; Chou, Sin-Yi; Yen, Yu-Ting; Chen, Hsuen-Li

    2015-03-07

    We have used a direct imprint-in-metal method that is cheap and rapid to prepare incident angle-tuned, broadband, ultrahigh-sensitivity plasmonic antennas from nanoparticles (NPs) and imprinted metal mirrors. By changing the angle of incidence, the nanoparticle-imprinted mirror antennas (NIMAs) exhibited broadband electromagnetic enhancement from the visible to the near-infrared (NIR) regime, making them suitable for use as surface-enhanced Raman scattering (SERS)-active substrates. Unlike other SERS-active substrates that feature various structures with different periods or morphologies, the NIMAs achieved broadband electromagnetic enhancement from single configurations. The enhancement of the electric field intensity in the NIMAs originated from coupling between the localized surface plasmon resonance of the NPs and the periodic structure-excited surface plasmon resonance (SPR) of the imprinted mirror. Moreover, the coupling wavelengths could be modulated because the SPR wavelength was readily tuned by changing the angle of the incident light. Herein, we demonstrate that such NIMAs are robust substrates for visible and NIR surface-enhanced resonance Raman scattering under multiple laser lines (532, 633, and 785 nm) of excitation. In addition, we have found that NIMAs are ultrasensitive SERS-active substrates that can detect analytes (e.g., rhodamine 6G) at concentrations as low as 10(-15) M.

  17. LUTE primary mirror materials and design study report

    Science.gov (United States)

    Ruthven, Greg

    1993-02-01

    The major objective of the Lunar Ultraviolet Telescope Experiment (LUTE) Primary Mirror Materials and Design Study is to investigate the feasibility of the LUTE telescope primary mirror. A systematic approach to accomplish this key goal was taken by first understanding the optical, thermal, and structural requirements and then deriving the critical primary mirror-level requirements for ground testing, launch, and lunar operations. After summarizing the results in those requirements which drove the selection of material and the design for the primary mirror are discussed. Most important of these are the optical design which was assumed to be the MSFC baseline (i.e. 3 mirror optical system), telescope wavefront error (WFE) allocations, the telescope weight budget, and the LUTE operational temperature ranges. Mechanical load levels, reflectance and microroughness issues, and options for the LUTE metering structure were discussed and an outline for the LUTE telescope sub-system design specification was initiated. The primary mirror analysis and results are presented. The six material substrate candidates are discussed and four distinct mirror geometries which are considered are shown. With these materials and configurations together with varying the location of the mirror support points, a total of 42 possible primary mirror designs resulted. The polishability of each substrate candidate was investigated and a usage history of 0.5 meter and larger precision cryogenic mirrors (the operational low end LUTE temperature of 60 K is the reason we feel a survey of cryogenic mirrors is appropriate) that were flown or tested are presented.

  18. Design and development of grazing incidence x-ray mirrors

    Science.gov (United States)

    Zuo, Fuchang; Mei, Zhiwu; Ma, Tao; Deng, Loulou; Shi, Yongqiang; Li, Liansheng

    2016-01-01

    X-ray pulsar navigation has attracted extensive attentions from academy and engineering domains. The navigation accuracy is can be enhanced through design of X-ray mirrors to focus X-rays to a small detector. The Wolter-I optics, originally proposed based on a paraboloid mirror and a hyperboloid mirror for X-ray imaging, has long been widely developed and employed in X-ray observatory. Some differences, however, remain in the requirements on optics between astronomical X-ray observation and pulsar navigation. The simplified Wolter-I optics, providing single reflection by a paraboloid mirror, is more suitable for pulsar navigation. In this paper, therefore, the grazing incidence X-ray mirror was designed further based on our previous work, with focus on the reflectivity, effective area, angular resolution and baffles. To evaluate the performance of the manufactured mirror, the surface roughness and reflectivity were tested. The test results show that the grazing incidence mirror meets the design specifications. On the basis of this, the reflectivity of the mirror in the working bandwidth was extrapolated to evaluate the focusing ability of the mirror when it works together with the detector. The purpose of our current work to design and develop a prototype mirror was realized. It can lay a foundation and provide guidance for the development of multilayer nested X-ray mirror with larger effective area.

  19. An array of directable mirrors as a photovoltaic solar concentrator

    Science.gov (United States)

    Ittner, W. B., III

    1980-01-01

    Calculations of the optics of heliostats for use in large thermal power towers have been carried out in considerable detail, chiefly by Vant-Hull et al. This paper describes a simplified method for calculating the images generated by a special type of concentrator, i.e. an array of independently steered mirrors on a single frame, intended to direct the solar image onto a flat photovoltaic solar cell target. The case of interest is one in which the field of illumination on the target is as uniform as possible, and the emphasis is thus on small 'rim angle' geometries (a configuration which also minimizes mirror interference effects). Calculations are presented for constructing the individual mirror target images in terms of three angles: (1) the angle between the photovoltaic target normal and the reflecting mirror (called here the mirror position angle), (2) the angle between the target center and the sun as measured from the center of the reflecting mirror, and (3) the angle at which the plane defined by the center of the sun, the mirror center and the target center intersects the plane of the target. The overall system efficiency for various mirror configurations, characterized by such parameters as the maximum mirror angle (i.e. 'rim angle'), target-mirror plane separation, and mirror aiming accuracy is discussed in terms of the specifications desirable in an optical concentrator designed specifically to illuminate uniformly a photovoltaic solar cell target.

  20. Mirror therapy in children with hemiplegia: a pilot study.

    Science.gov (United States)

    Gygax, Marine Jequier; Schneider, Patrick; Newman, Christopher John

    2011-05-01

    Mirror therapy, which provides the visual illusion of a functional paretic limb by using the mirror reflection of the non-paretic arm, is used in the rehabilitation of hemiparesis after stroke in adults. We tested the effectiveness and feasibility of mirror therapy in children with hemiplegia by performing a pilot crossover study in ten participants (aged 6-14 y; five males, five females; Manual Ability Classification System levels: one at level I, two at level II, four at level III, three at level IV) randomly assigned to 15 minutes of daily bimanual training with and without a mirror for 3 weeks. Assessments of maximal grasp and pinch strengths, and upper limb function measured by the Shriner's Hospital Upper Extremity Evaluation were performed at weeks 0 (baseline), 3, 6 (intervention), and 9 (wash-out). Testing of grasp strength behind the mirror improved performance by 15% (p=0.004). Training with the mirror significantly improved grasp strength (with mirror +20.4%, p=0.033; without +5.9%, p>0.1) and upper limb dynamic position (with mirror +4.6%, p=0.044; without +1.2%, p>0.1), while training without a mirror significantly improved pinch strength (with mirror +6.9%, p>0.1; without +21.9%, p=0.026). This preliminary study demonstrates the feasibility of mirror therapy in children with hemiplegia and that it may improve strength and dynamic function of the paretic arm.

  1. Optimum Design of Lightweight Silicon Carbide Mirror Assembly

    Institute of Scientific and Technical Information of China (English)

    HAN Yuanyuan; ZHANG Yumin; HAN Jiecai; ZHANG Jianhan; YAO Wang; ZHOU Yufeng

    2008-01-01

    According to the design requirement and on the basis of the principle that the thermal expansion coefficient of the support structure should match with that of the mirror, a lightweight silicon carbide primary mirror assembly was designed. Finite element analysis combined with the parameter-optimized method was used during the design. Lightweight cell and rigid rib structure were used for the mirror assembly. The static, dynamic and thermal properties of the primary mirror assembly were analyzed. It is shown that after optimization, the lightweight ratio of the silicon carbide mirror is 52.5%, and the rigidity of the silicon carbide structure is high enough to support the required mirror. When temperature changes, the deformation of the mirror surface is in proportion to the temperature difference.

  2. Plasma debris sputter resistant x-ray mirror.

    Science.gov (United States)

    Amano, Sho; Inoue, Tomoaki; Harada, Tetsuo

    2013-06-01

    A diamond-like carbon (DLC) mirror, used as a grazing incident mirror in a plasma x-ray source, exhibits a high resistance to plasma debris sputtering. Good mirror reflectivity at a wavelength of 13.5 nm was confirmed using synchrotron radiation at the NewSUBARU facility. The erosion rate due to plasma debris sputtered at the incident debris angle of 20° was measured using a laser-produced Xe plasma source developed by the authors. The results indicate that the DLC film has a 5- and 15-fold higher sputtering resistance compared to films made of the traditional mirror materials Ru and Au, respectively. Because the DLC mirror retains a high sputtering resistance to Sn ions, it may be effective in Sn plasma source applications. We conclude that a grazing incident x-ray mirror coated with DLC can be of use as a plasma debris sputtering resistant mirror.

  3. Monitoring of absolute mirror alignment at COMPASS RICH-1 detector

    Energy Technology Data Exchange (ETDEWEB)

    Alexeev, M. [INFN, Sezione di Torino and University of East Piemonte, Alessandria (Italy); INFN, Sezione di Trieste and University of Bari, Bari (Italy); Birsa, R. [INFN, Sezione di Trieste, Trieste (Italy); Bradamante, F.; Bressan, A. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy); Chiosso, M. [INFN, Sezione di Torino and University of Torino, Torino (Italy); Ciliberti, P. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy); Dalla Torre, S. [INFN, Sezione di Trieste, Trieste (Italy); Denisov, O. [INFN, Sezione di Torino, Torino (Italy); Duic, V. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy); Ferrero, A. [INFN, Sezione di Torino and University of Torino, Torino (Italy); Finger, M.; Finger, M. [Charles University, Prague (Czech Republic); JINR, Dubna (Russian Federation); Gayde, J.Ch. [CERN, European Organization for Nuclear Research, Geneva (Switzerland); Giorgi, M. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy); Gobbo, B.; Levorato, S. [INFN, Sezione di Trieste, Trieste (Italy); Maggiora, A. [INFN, Sezione di Torino, Torino (Italy); Martin, A. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy); Menon, G. [INFN, Sezione di Trieste, Trieste (Italy); Panzieri, D. [INFN, Sezione di Torino and University of East Piemonte, Alessandria (Italy); and others

    2014-12-01

    The gaseous COMPASS RICH-1 detector uses two spherical mirror surfaces, segmented into 116 individual mirrors, to focus the Cherenkov photons onto the detector plane. Any mirror misalignment directly affects the detector resolution. The on-line Continuous Line Alignment and Monitoring (CLAM) photogrammetry-based method has been implemented to measure the alignment of individual mirrors which can be characterized by the center of curvature. The mirror wall reflects a regular grid of retroreflective strips placed inside the detector vessel. Then, the position of each mirror is determined from the image of the grid reflection. The images are collected by four cameras. Any small mirror misalignment results in changes of the grid lines’ positions in the image. The accuracy limits of the CLAM method were checked by laser interferometry and are below 0.1 mrad.

  4. "Mirror agnosia" in a patient with right occipitotemporal infarct

    Directory of Open Access Journals (Sweden)

    Menon Bijoy

    2006-01-01

    Full Text Available We report the clinical profile and investigation of K, a patient suffering from agnosia for the concept of "mirrors". Normal people rarely confuse a mirror image for the real image. Our patient ′K′ has intact attention, memory and language with a left visual neglect with left hemianopia. When shown an object on his left with a mirror kept sagitally on his right, K grabs for the reflection and even gropes behind the mirror for it. Yet, when shown the mirror alone, he is able to tell that it is a mirror. Thus the concept of a ′mirror′ is lost in the experimental paradigm. An explanation for mirror ′agnosia′ is provided and recent controversies in the analysis of visuospatial functions in humans is highlighted.

  5. Cavity-mirror degradation in the deep-UV FEL

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, K.; Yamazaki, T.; Sei, N. [Electrotechnical Lab., Ibaraki (Japan)] [and others

    1995-12-31

    It is known that the degradation of dielectric multilayer mirrors used in short wavelength free-electron lasers (FELs) is caused by the carbon contamination on the mirror surface and the defects inside the dielectrics. We reported last year that the degraded dielectric multilayer mirrors can be repaired with both surface treatment by RF-induced oxygen plasma and thermal annealing. However, such a mirror degradation is still one of the most critical issues in the deep ultraviolet (UV) FELs, because the fundamental undulator radiation resonating in the laser cavity, the intensity of which is much higher than that of higher harmonics, can be sufficiently energetic to cause the mirror degradation through photochemical reactions. We are investigating the mirror degradation mainly in the deep UV region down to 240 nm. The experimental results will be shown. The mirror degradation mechanism will be discussed.

  6. Nonlinear Mirror Modes in Space Plasmas

    CERN Document Server

    Sulem, P -L

    2011-01-01

    Since the first observations by Kaufmann et al.\\ (1970), special attention has been paid to static pressure-balanced structures in the form of magnetic holes or humps observed in regions of the solar wind and of planetary magnetosheaths where the $\\beta$ parameter is relatively large and the ion perpendicular temperature exceeds the parallel one. Although alternative interpretations have been proposed, these structures are usually viewed as associated with the mirror instability discovered in 1957 by Vedenov and Sagdeev. After reviewing observational results provided by satellite missions, high-resolution numerical simulations of the Vlasov--Maxwell equations together with asymptotic and phenomenological models of the nonlinear dynamics near the instability threshold are discussed. The constraining effect of the mirror instability on the temperature anisotropy associated with a dominant perpendicular ion heating observed in the solar wind is reported, and recent simulations of this phenomenon based on an elab...

  7. Mirror decay of {sup 75}Sr

    Energy Technology Data Exchange (ETDEWEB)

    Huikari, J.; Huang, W.X. [Department of Physics, University of Jyvaeskylae, P.O. Box 35, FIN-40351, Jyvaeskylae (Finland); Oinonen, M. [Helsinki Institute of Physics, FIN-00014 University of Helsinki (Finland); CERN, CH-1211 Geneva 23 (Switzerland); Algora, A.; Nacher, E. [Instituto de Fisica Corpuscular, CSIC - University of Valencia, E-46071 Valencia (Spain); Cederkaell, J.; Fraile, L.; Franchoo, S.; Fynbo, H.; Peraejaervi, K.; Weissman, L. [CERN, CH-1211 Geneva 23 (Switzerland); Courtin, S.; Dessagne, P.; Knipper, A.; Marechal, F.; Miehe, C.; Poirier, E. [Institut de Recherches Subatomiques, F-67037 Strasbourg Cedex 2 (France); Jokinen, A.; Aeystoe, J. [Department of Physics, University of Jyvaeskylae, P.O. Box 35, FIN-40351, Jyvaeskylae (Finland); Helsinki Institute of Physics, FIN-00014 University of Helsinki (Finland)

    2003-03-01

    The {beta}-decay of {sup 75}Sr to its mirror nucleus {sup 75}Rb was studied at the ISOLDE PSB facility at CERN by means of {beta}-delayed {gamma} and proton spectroscopy. The decay Q-value and {beta}-delayed {gamma} intensity were measured for the first time. These results, 10.60{+-}0.22 MeV and 4.5{sup +1.9}{sub -0.7}%, together with accurate measurements of the {beta}-decay half-life and {beta}-delayed proton branching ratio yielded the Gamow-Teller strength 0.35{+-}0.05 for the mirror transition. Implications of the results on studies of deformation effects and on the path of the rapid proton capture process are discussed. (orig.)

  8. Dynamic aspects of segmented mirror position control

    Science.gov (United States)

    Kaercher, Hans J.

    2006-02-01

    Extreme large optical telescopes will operate in an open environment and may be excited by wind effects. The position control of the mirror segments may need fast control, and the position actuators and the related control loops may be separated in a conventional slow, iso-static and a fast reaction-mass type system. There exists some experience with wind excitations of airborne telescopes, e.g. the Stratospheric Observatory for Infrared Astronomy SOFIA. The pointing control system of that telescope is equipped with several dedicated design features, as a vibration isolations system, a flexible body control system and an active mass damper system to handle excitations in different frequency ranges. These features may be transferred to the position control systems of segmented mirrors. The paper will give some system engi-neers recommendations for designing those systems.

  9. Method of Making Lightweight, Single Crystal Mirror

    Science.gov (United States)

    Bly, Vincent T. (Inventor)

    2015-01-01

    A method of making a mirror from a single crystal blank may include fine grinding top and bottom surfaces of the blank to be parallel. The blank may then be heat treated to near its melting temperature. An optical surface may be created on an optical side of the blank. A protector may be bonded to the optical surface. With the protector in place, the blank may be light weighted by grinding a non-optical surface of the blank using computer controlled grinding. The light weighting may include creating a structure having a substantially minimum mass necessary to maintain distortion of the mirror within a preset limit. A damaged layer of the non-optical surface caused by light weighting may be removed with an isotropic etch and/or repaired by heat treatment. If an oxide layer is present, the entire blank may then be etched using, for example, hydrofluoric acid. A reflecting coating may be deposited on the optical surface.

  10. Mirror reflections of a black hole

    Science.gov (United States)

    Good, Michael R. R.; Anderson, Paul R.; Evans, Charles R.

    2016-09-01

    An exact correspondence between a black hole and an accelerating mirror is demonstrated. It is shown that for a massless minimally coupled scalar field, the same Bogolubov coefficients connecting the "in" and "out" states occur for a (1 +1 )-dimensional flat spacetime with a particular perfectly reflecting accelerating boundary trajectory and a (1 +1 )-dimensional curved spacetime in which a null shell collapses to form a black hole. Generalization of the latter to the (3 +1 )-dimensional case is discussed. The spectral dynamics is computed in both (1 +1 )-dimensional spacetimes along with the energy flux in the spacetime with a mirror. It is shown that the approach to equilibrium is monotonic, asymmetric in terms of the rate, and there is a specific time which characterizes the system when it is the most out of equilibrium.

  11. Enhancing nanoparticle electrodynamics with gold nanoplate mirrors.

    Science.gov (United States)

    Yan, Zijie; Bao, Ying; Manna, Uttam; Shah, Raman A; Scherer, Norbert F

    2014-05-14

    Mirrors and optical cavities can modify and enhance matter-radiation interactions. Here we report that chemically synthesized Au nanoplates can serve as micrometer-size mirrors that enhance electrodynamic interactions. Because of their plasmonic properties, the Au nanoplates enhance the brightness of scattered light from Ag nanoparticles near the nanoplate surface in dark-field microscopy. More importantly, enhanced optical trapping and optical binding of Ag nanoparticles are demonstrated in interferometric optical traps created from a single laser beam and its reflection from individual Au nanoplates. The enhancement of the interparticle force constant is ≈20-fold more than expected from the increased intensity due to standing wave interference. We show that the additional stability for optical binding arises from the restricted axial thermal motion of the nanoparticles that couples to and reduces the fluctuations in the lateral plane. This new mechanism greatly advances the photonic synthesis of ultrastable nanoparticle arrays and investigation of their properties.

  12. Mirror Instability in the Turbulent Solar Wind

    Science.gov (United States)

    Hellinger, Petr; Landi, Simone; Matteini, Lorenzo; Verdini, Andrea; Franci, Luca

    2017-04-01

    The relationship between a decaying strong turbulence and the mirror instability in a slowly expanding plasma is investigated using two-dimensional hybrid expanding box simulations. We impose an initial ambient magnetic field perpendicular to the simulation box, and we start with a spectrum of large-scale, linearly polarized, random-phase Alfvénic fluctuations that have energy equipartition between kinetic and magnetic fluctuations and a vanishing correlation between the two fields. A turbulent cascade rapidly develops, magnetic field fluctuations exhibit a Kolmogorov-like power-law spectrum at large scales and a steeper spectrum at sub-ion scales. The imposed expansion (taking a strictly transverse ambient magnetic field) leads to the generation of an important perpendicular proton temperature anisotropy that eventually drives the mirror instability. This instability generates large-amplitude, nonpropagating, compressible, pressure-balanced magnetic structures in a form of magnetic enhancements/humps that reduce the perpendicular temperature anisotropy.

  13. Brainstem hypoplasia presenting with mirror movement

    Directory of Open Access Journals (Sweden)

    Burcu Ekmekçi

    2015-09-01

    Full Text Available 20 years old female patient, who had operated from congenital syndactyly on her left hand at five age, admitted to neurology policlinic with involuntary movement on her hands. We saw mirror movement (MM when she writing, catching with her left hand. This movement is had low amplitude in the right hand than left. Cervical MRG revealed no abnormality. Brain MRG revealed right middle, inferior cerebellary peduncle, olive and pyramid hypoplasia. Mirror movement shows homolog muscle activity which simulating contralateral movement, during a spesific task. This movement is seen usually upper extremity especially in the hand. Corticospinal tract dysfunction is often considered in the pathogenesis. MM may present as part of cervico medullary junction abnormality, cerebral palsy, cerebrovasculary disease, Parkinson disease. We wanted to discuss the patogenesis of MM in our patient with syndactyly and MRG abnormality.

  14. Electrochromic mirror using viologen-anchored nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Han Na [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); University of Science and Technology, Advanced Device Technology, 217 Gajeong-roYuseong-gu, Daejeon 305-350 (Korea, Republic of); Cho, Seong M.; Ah, Chil Seong; Song, Juhee; Ryu, Hojun; Kim, Yong Hae [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); Kim, Tae-Youb, E-mail: youby@etri.re.kr [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); University of Science and Technology, Advanced Device Technology, 217 Gajeong-roYuseong-gu, Daejeon 305-350 (Korea, Republic of)

    2016-10-15

    Highlights: • Three types of ECM device were fabricated using viologen-anchored ECDs. • The devices were investigated according to their optical structures. • The anti-reflection material affects the reflectance and the coloration efficiency. • The device design of ECMs is a crucial factor for clear reflected images. - Abstract: Electrochromic mirrors (ECMs) that are used in automobile mirrors need to have high reflectance, a high contrast ratio, and a clear image. In particular, it is critical that distortions of clear images are minimized for safety. Therefore, an ECM is fabricated using viologen-anchored nanoparticles and a magnesium fluoride (MgF{sub 2}) layer with an anti-reflection function. The ECM has approximately 30.42% in the reflectance dynamic range and 125 cm{sup 2}/C high coloration efficiency.

  15. Omnidirectional mirror coating design for infrared applications

    Energy Technology Data Exchange (ETDEWEB)

    Lusk, D. [Electronic Engineering and Physics Division, Thin Film Centre, University of Paisley, Paisley PA1 2BE, Scotland (United Kingdom)]. E-mail: lusk-ph0@wpmail.paisley.ac.uk; Placido, F. [Electronic Engineering and Physics Division, Thin Film Centre, University of Paisley, Paisley PA1 2BE, Scotland (United Kingdom)

    2005-12-01

    An omnidirectional mirror, with a reflectance (R) of 99.5% for all angles of incidence and both polarisations, was designed from quasi-periodic dielectric stacks based on Fibonacci sequence (FS) by selecting appropriate materials for high and low refractive index layers. At R = 99.5%, the initial omnidirectional spectral range was found to be from 1437 to 1618 nm, which covers completely the telecommunications wavelength region and the S, C and L bands of the erbium doped fiber amplifier gain region. The individual layers within the FS have the same physical thickness, thus having non quarter-wave optical thickness at the centre wavelength. Optimisation from the initial design can expand the omnidirectional spectral region at R = 99.5%, as well as show a higher value of R over the initial omnidirectional spectral range. Deposition and characterisation of the mirror coating have taken place using microwave assisted direct current magnetron sputtering and various characterisation techniques.

  16. Operators and higher genus mirror curves

    Science.gov (United States)

    Codesido, Santiago; Gu, Jie; Mariño, Marcos

    2017-02-01

    We perform further tests of the correspondence between spectral theory and topological strings, focusing on mirror curves of genus greater than one with nontrivial mass parameters. In particular, we analyze the geometry relevant to the SU(3) relativistic Toda lattice, and the resolved C{^3}/Z_6 orbifold. Furthermore, we give evidence that the correspondence holds for arbitrary values of the mass parameters, where the quantization problem leads to resonant states. We also explore the relation between this correspondence and cluster integrable systems.

  17. Operators and higher genus mirror curves

    CERN Document Server

    Codesido, Santiago; Marino, Marcos

    2016-01-01

    We perform further tests of the correspondence between spectral theory and topological strings, focusing on mirror curves of genus greater than one with nontrivial mass parameters. In particular, we analyze the geometry relevant to the SU(3) relativistic Toda lattice, and the resolved C^3/Z_6 orbifold. Furthermore, we give evidence that the correspondence holds for arbitrary values of the mass parameters, where the quantization problem leads to resonant states. We also explore the relation between this correspondence and cluster integrable systems.

  18. Black Hole - Moving Mirror II: Particle Creation

    OpenAIRE

    Good, Michael R. R.; Anderson, Paul R.; Evans, Charles R.

    2015-01-01

    There is an exact correspondence between the simplest solution to Einstein's equations describing the formation of a black hole and a particular moving mirror trajectory. In both cases the Bogolubov coefficients in 1+1 dimensions are identical and can be computed analytically. Particle creation is investigated by using wave packets. The entire particle creation history is computed, incorporating the early-time non-thermal emission due to the formation of the black hole (or the early-time acce...

  19. Superradiance by mini black holes with mirror

    OpenAIRE

    Lee, Jong-Phil

    2011-01-01

    The superradiant scattering of massive scalar particles by a rotating mini black hole is investigated. Imposing the mirror boundary condition, the system becomes the so called black-hole bomb where the rotation energy of the black hole is transferred to the scattered particle exponentially with time. Bulk emissions as well as brane emissions are considered altogether. It is found that the largest effects are expected for the brane emission of lower angular modes with lighter mass and larger a...

  20. Mirror Prescription Regression: A Differential Interferometric Technique

    Directory of Open Access Journals (Sweden)

    Brian M. Robinson

    2010-01-01

    Full Text Available We present a remote, differential method for measuring the prescription of aspheric mirrors using null interferometry in the center-of-curvature configuration. The method requires no equipment beyond that used in a basic interferometery setup (i.e., there are no shearing elements or absolute distance meters. We chose this configuration because of its widespread use. However, the method is generalizable to other configurations with an adjustment of the governing equation. The method involves taking a series of interferograms before and after small, known misalignments are applied to the mirror in the interferometry setup and calculating the prescription (e.g., radius of curvature and conic constant of the mirror, based on these differential measurements, using a nonlinear regression. We apply this method successfully to the testing of a Space Optics Research Lab off-axis parabola with a known focal length of 152.4 mm, a diameter of 76.2 mm, and an off-axis angle of 12°.

  1. The Mirror Neuron System: A Fresh View

    Science.gov (United States)

    Casile, Antonino; Caggiano, Vittorio; Ferrari, Pier Francesco

    2013-01-01

    Mirror neurons are a class of visuomotor neurons in the monkey premotor and parietal cortices that discharge during the execution and observation of goal-directed motor acts. They are deemed to be at the basis of primates’ social abilities. In this review, the authors provide a fresh view about two still open questions about mirror neurons. The first question is their possible functional role. By reviewing recent neurophysiological data, the authors suggest that mirror neurons might represent a flexible system that encodes observed actions in terms of several behaviorally relevant features. The second question concerns the possible developmental mechanisms responsible for their initial emergence. To provide a possible answer to question, the authors review two different aspects of sensorimotor development: facial and hand movements, respectively. The authors suggest that possibly two different “mirror” systems might underlie the development of action understanding and imitative abilities in the two cases. More specifically, a possibly prewired system already present at birth but shaped by the social environment might underlie the early development of facial imitative abilities. On the contrary, an experience-dependent system might subserve perception-action couplings in the case of hand movements. The development of this latter system might be critically dependent on the observation of own movements. PMID:21467305

  2. Mirror contamination in space I: approach

    Science.gov (United States)

    Krijger, J. M.; Snel, R.; van Harten, G.; Rietjens, J. H. H.; Aben, I.

    2014-02-01

    We present a comprehensive model that can be employed to describe and correct for degradation of (scan) mirrors and diffusers in satellite instruments that suffer from changing optical UV-VIS properties during their operational lifetime. As trend studies become more important, so does the importance to understand and correct for this degradation. This is the case not only with respect to the transmission of the optical components, but also with respect to wavelength, polarisation or scan-angle-effects. Our hypothesis is that mirrors in-flight suffer from the deposition of a thin absorbing layer of contaminant, which slowly builds up over time. We describe this with the Mueller matrix formalism and Fresnel equations for thin multi-layer contamination films. Special care is taken to avoid the confusion often present in earlier publications concerning Mueller matrix calculus with out of plane reflections. The method can be applied to any UV-VIS satellite instrument, and in any orbit, both low and geostationary. We illustrate and verify our approach on the optical behaviour of the multiple scan mirrors of SCIAMACHY (on board of ENVISAT).

  3. Mirror seeing of the Antarctic survey telescope

    Institute of Scientific and Technical Information of China (English)

    ZHANG Kaiyuan; LI Zhengyang; YUAN Xiangyan; PEI Chong

    2014-01-01

    Site testing results indicate that Antarctic Dome A is an excellent ground-based astronomical site suitable for observations ranging from visible to infrared wavelengths. However, the harsh environment in Antarctica, especially the very low temperature and atmospheric pressure, always produces frost on the telescopes’ mirrors, which are exposed to the air. Since the Dome A site is still unattended, the Antarctic telescope tubes are always designed to be filled with dry nitrogen, and the outer surfaces of the optical system are heated by an indium-tin oxide thin film. These precautions can prevent the optical surfaces from frosting over, but they degrade the image quality by introducing additional mirror seeing. Based on testing observations of the second Antarctic Survey Telescope (AST3-2) in the Mohe site in China, mirror seeing resulting from the heated aspheric plate has been measured using micro-thermal sensors. Results comparing the real-time atmospheric seeing monitored by the Differential Image Motion Monitor and real-time examinations of image quality agree well.

  4. Thin Shell, Segmented X-Ray Mirrors

    Science.gov (United States)

    Petre, Robert

    2010-01-01

    Thin foil mirrors were introduced as a means of achieving high throughput in an X-ray astronomical imaging system in applications for which high angular resolution were not necessary. Since their introduction, their high filling factor, modest mass, relative ease of construction, and modest cost have led to their use in numerous X-ray observatories, including the Broad Band X-ray Telescope, ASCA, and Suzaku. The introduction of key innovations, including epoxy replicated surfaces, multilayer coatings, and glass mirror substrates, has led to performance improvements, and in their becoming widely used for X-ray astronomical imaging at energies above 10 keV. The use of glass substrates has also led to substantial improvement in angular resolution, and thus their incorporation into the NASA concept for the International X-ray Observatory with a planned 3 in diameter aperture. This paper traces the development of foil mirrors from their inception in the 1970's through their current and anticipated future applications.

  5. Mirror Surface Reconstruction from a Single Image.

    Science.gov (United States)

    Liu, Miaomiao; Hartley, Richard; Salzmann, Mathieu

    2015-04-01

    This paper tackles the problem of reconstructing the shape of a smooth mirror surface from a single image. In particular, we consider the case where the camera is observing the reflection of a static reference target in the unknown mirror. We first study the reconstruction problem given dense correspondences between 3D points on the reference target and image locations. In such conditions, our differential geometry analysis provides a theoretical proof that the shape of the mirror surface can be recovered if the pose of the reference target is known. We then relax our assumptions by considering the case where only sparse correspondences are available. In this scenario, we formulate reconstruction as an optimization problem, which can be solved using a nonlinear least-squares method. We demonstrate the effectiveness of our method on both synthetic and real images. We then provide a theoretical analysis of the potential degenerate cases with and without prior knowledge of the pose of the reference target. Finally we show that our theory can be similarly applied to the reconstruction of the surface of transparent object.

  6. Mirror-Like Mechanisms and Music

    Directory of Open Access Journals (Sweden)

    Alessandro D'Ausilio

    2009-01-01

    Full Text Available The neural processes underlying sensory-motor integration have always attracted strong interest. The classic view is that action and perception are two extremes of mental operations. In the past 2 decades, though, a large number of discoveries have indeed refuted such an interpretation in favor of a more integrated view. Specifically, the discovery of mirror neurons in monkey premotor cortex is a rather strong demonstration that sensory and motor processes share the same neural substrates. In fact, these cells show complex sensory-motor properties, such that observed, heard, or executed goal-directed actions could equally activate these neurons. On the other hand, the neuroscience of music has similarly emerged as an active and productive field of research. In fact, music-related behaviors are a useful model of action-perception mechanisms and how they develop through training. More recently, these two lines of research have begun to intersect into a novel branch of research. As a consequence, it has been proposed recently that mirror-like mechanisms might be at the basis of human music perception-production abilities. The scope of the present short review is to set the scientific background for mirror-like mechanisms in music by examining recent published data.

  7. Correction of an active space telescope mirror using a deformable mirror in a woofer-tweeter configuration

    Science.gov (United States)

    Allen, Matthew R.; Kim, Jae Jun; Agrawal, Brij N.

    2016-04-01

    The Naval Postgraduate School's segmented mirror telescope (SMT) was developed using prototype silicon carbide active hybrid mirror technology to demonstrate lower cost and rapid manufacture of primary mirror segments for a space telescope. The developmental mirror segments used too few actuators limiting the ability to adequately correct the surface figure error. To address the unintended shortfall of the developmental mirrors, a deformable mirror is added to the SMT and control techniques are developed. The control techniques are similar to woofer-tweeter adaptive optics, where the SMT segment represents the woofer and the deformable mirror represents the tweeter. The optical design of an SMT woofer-tweeter system is presented, and the impacts of field angle magnification on the placement and size of the deformable mirror are analyzed. A space telescope woofer-tweeter wavefront control technique is proposed using a global influence matrix and closed-loop constrained minimization controller. The control technique simultaneously manipulates the woofer and tweeter mirrors. Simulation and experimental results demonstrate a significant improvement in wavefront error of the primary mirror and the control technique shows significant wavefront error improvement compared to sequentially controlling the woofer and tweeter mirrors.

  8. Process of constructing a lightweight x-ray flight mirror assembly

    Science.gov (United States)

    McClelland, Ryan S.; Biskach, Michael P.; Chan, Kai-Wing; Espina, Rebecca A.; Hohl, Bruce R.; Saha, Timo T.; Zhang, William W.

    2014-07-01

    Lightweight and high resolution optics are needed for future space-based x-ray telescopes to achieve advances in highenergy astrophysics. NASA's Next Generation X-ray Optics (NGXO) project has made significant progress towards building such optics, both in terms of maturing the technology for spaceflight readiness and improving the angular resolution. Technology Development Modules (TDMs) holding three pairs of mirrors have been regularly and repeatedly integrated and tested both for optical performance and mechanical strength. X-ray test results have been improved over the past year from 10.3 arc-seconds Half Power Diameter (HPD) to 8.3 arc-seconds HPD. A vibration test has been completed to NASA standard verification levels showing the optics can survive launch and pointing towards improvements in strengthening the modules through redundant bonds. A Finite Element Analysis (FEA) study was completed which shows the mirror distortion caused by bonding is insensitive to the number of bonds. Next generation TDMs, which will demonstrate a lightweight structure and mount additional pairs of mirrors, have been designed and fabricated. The light weight of the module structure is achieved through the use of E-60 Beryllium Oxide metal matrix composite material. As the angular resolution of the development modules has improved, gravity distortion during horizontal x-ray testing has become a limiting factor. To address this issue, a facility capable of testing in the vertical orientation has been designed and planned. Test boring at the construction site suggest standard caisson construction methods can be utilized to install a subterranean vertical vacuum pipe. This facility will also allow for the testing of kinematically mounted mirror segments, which greatly reduces the effect of bonding displacements. A development platform demonstrating the feasibility of kinematically mounting mirror segments has been designed, fabricated, and successfully tested.

  9. Optimization of interference filters with genetic algorithms applied to silver-based heat mirrors.

    Science.gov (United States)

    Eisenhammer, T; Lazarov, M; Leutbecher, M; Schöffel, U; Sizmann, R

    1993-11-01

    In the optimization of multilayer stacks for various optical filtering purposes not only the thicknesses of the thin films are to be optimized, but also the sequence of materials. Materials with very different optical properties, such as metals and dielectrics, may be combined. A genetic algorithm is introduced to search for the optimal sequence of materials along with their optical thicknesses. This procedure is applied to a heat mirror in combination with a blackbody absorber for thermal solar energy applications at elevated temperatures (250 °C). The heat mirror is based on silver films with antireflective dielectric layers. Seven dielectrics have been considered. For a five-layer stack the sequence (TiO(2)/Ag/TiO(2)/Ag/Y(2)O(3)) is found to be optimal.

  10. Mirror, Mirror

    Science.gov (United States)

    Fuentes, Sarah Quebec

    2015-01-01

    NCTM's "Principles to Actions: Ensuring Mathematical Success for All" (2014), outlines eight teaching practices for effective teaching and learning mathematics. One of them, facilitate meaningful mathematical discourse, states, "Effective teaching of mathematics facilitates discourse among students to build shared understanding of…

  11. Experimental Study on One-mirror-inclined Three-mirror-cavity Photodetectors

    Institute of Scientific and Technical Information of China (English)

    HUANG Hui(黄辉); ZHANG Ruikang(张瑞康); WANG Qi(王琦); HUANG Yongqing(黄永清); REN Xiaomin(任晓敏)

    2002-01-01

    Research on the one-mirror-inclined three-mirror-cavity (OMITMiC) photodetectors in the laboratory is reported. In the structure of photodetectors, it is the inclined-mirror that makes the filtering cavity and the absorption cavity decoupled, thus narrow spectral response linewidth, wavelength-tunable and high quantum efficiency can be achieved simultaneously. On the basis of the theoretical analysis and experimental verification on the principle with separated optical components, the vertical taper structure, the key part in the whole integrated device was realized, by dynamic etch mask technique. Moreover, the first integrated device of this type was fabricated. A spectral linewidth less than 6 nm and a quantum efficiency of 52.6% have been achieved experimentally.

  12. Adaptive aberration correction using a triode hyperbolic electron mirror.

    Science.gov (United States)

    Fitzgerald, J P S; Word, R C; Könenkamp, R

    2011-01-01

    A converging electron mirror can be used to compensate spherical and chromatic aberrations in an electron microscope. This paper presents an analytical solution to a novel triode (three electrode) hyperbolic mirror as an improvement to the well-known diode (two electrode) hyperbolic mirror for aberration correction. A weakness of the diode mirror is a lack of flexibility in changing the chromatic and spherical aberration coefficients independently without changes in the mirror geometry. In order to remove this limitation, a third electrode can be added. We calculate the optical properties of the resulting triode mirror analytically on the basis of a simple model field distribution. We present the optical properties-the object/image distance, z(0), and the coefficients of spherical and chromatic aberration, C(s) and C(c), of both mirror types from an analysis of electron trajectories in the mirror field. From this analysis, we demonstrate that while the properties of both designs are similar, the additional parameters in the triode mirror improve the range of aberration that can be corrected. The triode mirror is also able to provide a dynamic adjustment range of chromatic aberration for fixed spherical aberration and focal length, or any permutation of these three parameters. While the dynamic range depends on the values of aberration correction needed, a nominal 10% tuning range is possible for most configurations accompanied by less than 1% change in the other two properties.

  13. Analysis of a one mirror inclined three-mirror cavity photodetector for high-speed application

    Institute of Scientific and Technical Information of China (English)

    Yongqing Huang; Cheng Huang; Qi Wang; Hui Huang; Xingyan Wang; Xiaomin Ren

    2005-01-01

    @@ There is a tradeoff between the quantum efficiency and the spectral response linewidth in resonant-cavityenhanced (RCE) photodetectors. Recently a new type of photodetector structure has been proposed, which utilizes an inclined mirror in a three-mirror cavity. It decouples the quantum efficiency and the spectral response linewidth and has high response speed, high quantum efficiency, and narrow linewidth simultaneously. The analysis result indicates that the linewidth of 0.8 nm and quantum efficiency higher than 70%can be achieved on this device. For a 30×30 μm2 device, the maximum bandwidth approaches 23 GHz.

  14. Spontaneous expression of mirror self-recognition in monkeys after learning precise visual-proprioceptive association for mirror images.

    Science.gov (United States)

    Chang, Liangtang; Zhang, Shikun; Poo, Mu-Ming; Gong, Neng

    2017-03-21

    Mirror self-recognition (MSR) is generally considered to be an intrinsic cognitive ability found only in humans and a few species of great apes. Rhesus monkeys do not spontaneously show MSR, but they have the ability to use a mirror as an instrument to find hidden objects. The mechanism underlying the transition from simple mirror use to MSR remains unclear. Here we show that rhesus monkeys could show MSR after learning precise visual-proprioceptive association for mirror images. We trained head-fixed monkeys on a chair in front of a mirror to touch with spatiotemporal precision a laser pointer light spot on an adjacent board that could only be seen in the mirror. After several weeks of training, when the same laser pointer light was projected to the monkey's face, a location not used in training, all three trained monkeys successfully touched the face area marked by the light spot in front of a mirror. All trained monkeys passed the standard face mark test for MSR both on the monkey chair and in their home cage. Importantly, distinct from untrained control monkeys, the trained monkeys showed typical mirror-induced self-directed behaviors in their home cage, such as using the mirror to explore normally unseen body parts. Thus, bodily self-consciousness may be a cognitive ability present in many more species than previously thought, and acquisition of precise visual-proprioceptive association for the images in the mirror is critical for revealing the MSR ability of the animal.

  15. Aspherical mirrors for the Gamma-ray Cherenkov Telescope, a Schwarschild-Couder prototype proposed for the future Cherenkov Telescope Array

    Science.gov (United States)

    Dournaux, J. L.; Gironnet, J.; Huet, J. M.; Laporte, P.; Chadwick, P.; Dumas, D.; Pech, M.; Rulten, C. B.; Sayède, F.; Schmoll, J.; Sol, H.

    2016-07-01

    The Cherenkov Telescope Array (CTA) project, led by an international collaboration of institutes, aims to create the world's largest next generation Very High-Energy (VHE) gamma-ray telescope array, devoted to observations in a wide band of energy, from a few tens of GeV to more than 100 TeV. The Small-Sized Telescopes (SSTs) are dedicated to the highest energy range. Seventy SSTs are planned in the baseline array design with a required lifetime of about 30 years. The GCT (Gamma-ray Cherenkov Telescope) is one of the prototypes proposed for CTA's SST sub-array. It is based on a Schwarzschild-Couder dual-mirror optical design. This configuration has the benefit of increasing the field-of-view and decreasing the masses of the telescope and of the camera. But, in spite of these many advantages, it was never implemented before in ground-based Cherenkov astronomy because of the aspherical and highly curved shape required for the mirrors. The optical design of the GCT consists of a primary 4 meter diameter mirror, segmented in six aspherical petals, a secondary monolithic 2-meter mirror and a light camera. The reduced number of segments simplifies the alignment of the telescope but complicates the shape of the petals. This, combined with the strong curvature of the secondary mirror, strongly constrains the manufacturing process. The Observatoire de Paris implemented metallic lightweight mirrors for the primary and the secondary mirrors of GCT. This choice was made possible because of the relaxed requirements of optical Cherenkov telescopes compared to optical ones. Measurements on produced mirrors show that these ones can fulfill requirements in shape, PSF and reflectivity, with a clear competition between manufacturing cost and final performance. This paper describes the design of these mirrors in the context of their characteristics and how design optimization was used to produce a lightweight design. The manufacturing process used for the prototype and planned for the

  16. Wavefront Compensation Segmented Mirror Sensing and Control

    Science.gov (United States)

    Redding, David C.; Lou, John Z.; Kissil, Andrew; Bradford, Charles M.; Woody, David; Padin, Stephen

    2012-01-01

    The primary mirror of very large submillimeter-wave telescopes will necessarily be segmented into many separate mirror panels. These panels must be continuously co-phased to keep the telescope wavefront error less than a small fraction of a wavelength, to ten microns RMS (root mean square) or less. This performance must be maintained continuously across the full aperture of the telescope, in all pointing conditions, and in a variable thermal environment. A wavefront compensation segmented mirror sensing and control system, consisting of optical edge sensors, Wavefront Compensation Estimator/Controller Soft ware, and segment position actuators is proposed. Optical edge sensors are placed two per each segment-to-segment edge to continuously measure changes in segment state. Segment position actuators (three per segment) are used to move the panels. A computer control system uses the edge sensor measurements to estimate the state of all of the segments and to predict the wavefront error; segment actuator commands are computed that minimize the wavefront error. Translational or rotational motions of one segment relative to the other cause lateral displacement of the light beam, which is measured by the imaging sensor. For high accuracy, the collimator uses a shaped mask, such as one or more slits, so that the light beam forms a pattern on the sensor that permits sensing accuracy of better than 0.1 micron in two axes: in the z or local surface normal direction, and in the y direction parallel to the mirror surface and perpendicular to the beam direction. Using a co-aligned pair of sensors, with the location of the detector and collimated light source interchanged, four degrees of freedom can be sensed: transverse x and y displacements, as well as two bending angles (pitch and yaw). In this approach, each optical edge sensor head has a collimator and an imager, placing one sensor head on each side of a segment gap, with two parallel light beams crossing the gap. Two sets

  17. Mirroring Facial Expressions and Emotions in Dyadic Conversations

    DEFF Research Database (Denmark)

    Navarretta, Costanza

    2016-01-01

    This paper presents an investigation of mirroring facial expressions and the emotions which they convey in dyadic naturally occurring first encounters. Mirroring facial expressions are a common phenomenon in face-to-face interactions, and they are due to the mirror neuron system which has been...... and overlapping facial expressions are very frequent. In this study, we want to determine whether the overlapping facial expressions are mirrored or are otherwise correlated in the encounters, and to what extent mirroring facial expressions convey the same emotion. The results of our study show that the majority...... of smiles and laughs, and one fifth of the occurrences of raised eyebrows are mirrored in the data. Moreover some facial traits in co-occurring expressions co-occur more often than it would be expected by chance. Finally, amusement, and to a lesser extent friendliness, are often emotions shared by both...

  18. Correction of low order aberrations using continuous deformable mirrors.

    Science.gov (United States)

    Vdovin, Gleb; Soloviev, Oleg; Samokhin, Alexander; Loktev, Mikhail

    2008-03-03

    By analyzing the Poisson equation describing the static behavior of membrane and bimorph deformable mirrors and biharmonic equation describing the continuous facesheet mirror with push-pull actuators, we found that to achieve a high quality correction of low-order aberrations these mirrors should have sufficient number of actuators positioned outside the correction aperture. In particular, any deformable mirror described by the Poisson equation requires at least two actuators to be placed outside the working aperture per period of the azimuthal aberration of the highest expected order. Any deformable mirror described by the biharmonic equation, such as a continuous facesheet mirror with push-pull actuators, requires at least four actuators to be placed outside the working aperture per period of the azimuthal aberration of the highest expected order, and these actuators should not be positioned on a single circle.

  19. Mirror Technology Roadmap for NASA's Exoplanet Exploration Program

    Science.gov (United States)

    Lawson, Peter R.; Shaklan, Stuart B.; Balasubramanian, K.

    2011-01-01

    There are several possible approaches to designing exoplanet missions: (1) Coronagraphs (2) Interferometers (3) Starshades Wavefront sensing and control is the central concern, not mirror size (1) Starlight suppression with deformable mirrors (2) Thermal and structural stability (3) Metrology for sensing and control Diffraction-limited optical primary mirrors 4-m or larger are needed to detect Earthlike planets (1) Surface figure similar to HST required (2) Smaller primary mirrors can be used with aggressive coronagraph designs, but the stability tolerances become the driving concern (3) Stability tolerances of coronagraphs are greatly reduced when larger primaries are used in conjunction with 8th-order masks Long term vision for large telescope development includes space-based segmented-mirror telescopes using actively-controlled glass segments or silicon carbide hybrid-mirror designs

  20. Effects of electron temperature anisotropy on proton mirror instability evolution

    Science.gov (United States)

    Ahmadi, Narges; Germaschewski, Kai; Raeder, Joachim

    2016-06-01

    Proton mirror modes are large amplitude nonpropagating structures frequently observed in the magnetosheath. It has been suggested that electron temperature anisotropy can enhance the proton mirror instability growth rate while leaving the proton cyclotron instability largely unaffected, therefore causing the proton mirror instability to dominate the proton cyclotron instability in Earth's magnetosheath. Here we use particle-in-cell simulations to investigate the electron temperature anisotropy effects on proton mirror instability evolution. Contrary to the hypothesis, electron temperature anisotropy leads to excitement of the electron whistler instability. Our results show that the electron whistler instability grows much faster than the proton mirror instability and quickly consumes the electron-free energy so that there is no electron temperature anisotropy left to significantly impact the evolution of the proton mirror instability.

  1. Disassembling and reintegration of large telescope primary mirror

    Science.gov (United States)

    Xu, Qi-rui; Fan, Bin; Zhang, Ming

    2014-09-01

    The success of the large telescope is largely linked to the excellent performance and reliability of the primary mirror. In order to maintain the quality of its reflective surface at the high expectations of astronomers, the primary mirror after almost two or three years of astronomical observations, needs to be removed and reinstalled for its cleaning and re-coating operation. There are a series of procedures such as the primary mirror cell dissembling from telescope, mirror handling, transportation, reintegration, alignment and so on. This paper will describe the experiences of disassembling and reintegration of large telescope primary mirror, taking a two meter grade primary mirror for example. As with all advanced and complex opto-mechanical systems, there has been the usual problems and trouble shooting.

  2. Rigid ultralight primary mirror segments for space telescopes

    Science.gov (United States)

    Zito, Richard R.

    2000-10-01

    The development of ultra-light fibrous substrate mirrors allows serious contemplation of large multi-mirror space telescopes using rigid segments. Mirrors made of silica and alumina fibers have a small coefficient of thermal expansion and a density competitive with inflatable structures. Furthermore, they are without the imagery problems caused by non parabolic figures, gaseous expansion and contraction, tidal distortion of large gas filled structures, leaks, and long lived transient mirror perturbations caused by intentional pointing and tracking movements, micrometeor and space debris impacts, and mechanical vibrations. Fibrous substrate primary mirrors also have logistical advantages, since segments can be fabricated in orbit from small amounts of dense raw materials. One space shuttle flight, lifting about half its payload capacity, is adequate to transport all the material necessary to fabricate substrates for a one hundred meter telescope whose primary mirror consists of 12,086 hexagonal segments, each having a diameter of 1 meter and an area of 0.6495 square meters.

  3. Interferometric measurements of silicon carbide mirrors at liquid helium temperature

    Science.gov (United States)

    Robb, Paul N.; Huff, Lynn W.; Forney, Paul B.; Petrovsky, Gury T.; Ljubarsky, Sergey V.; Khimitch, Yuri P.

    1995-10-01

    This paper presents the results of interferometric tests of two silicon carbide mirrors tested at room temperature and 6 K. The first mirror has a spherical f/1.73 surface, a diameter of 170 mm, and is of solid, plano-concave construction. The other mirror, a plano measuring 308 mm by 210 mm, is of lightweighted, closed-back construction. The mirrors were manufactured by the Vavilov State Optical Institute, St. Petersburg, Russia, and were loaned to Lockheed for these tests. Optical tests on both mirrors were performed using the Lockheed cryogenic optical test facility at liquid helium temperature and a Zygo Mark II interferometer. There was no change in the surface figure of the mirrors, within the test uncertainty of approximately plus or minus 0.02 waves at 0.6328-micrometer wavelength.

  4. Doing it with Mirrors Classical analogues for Black Hole radiation

    CERN Document Server

    Srinivasan, K

    1998-01-01

    We construct analogues for the quantum phenomena of black hole radiation in the context of {\\it classical field theory}. Hawking radiation from a (radially) collapsing star is mathematically equivalent to radiation from a mirror moving along a specific trajectory in Minkowski spacetime. We construct a classical analogue for this quantum phenomenon and use it to construct a classical analogue for black hole radiation. The radiation spectrum in quantum field theory has the power spectrum as its classical analogue. Monochromatic light is continually reflected off a moving mirror or the silvered surface of a collapsing star.The reflected light is fourier analysed by the observer and the power spectrum is constructed. For a mirror moving along the standard black hole trajectory,it is seen that the power spectrum has a ``thermal'' nature. Mirror-observer configurations like an inertial mirror observed in an accelerated observer's frame and an accelerated mirror observed in a Rindler frame are investigated and condi...

  5. Error reduction techniques for measuring long synchrotron mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Irick, S.

    1998-07-01

    Many instruments and techniques are used for measuring long mirror surfaces. A Fizeau interferometer may be used to measure mirrors much longer than the interferometer aperture size by using grazing incidence at the mirror surface and analyzing the light reflected from a flat end mirror. Advantages of this technique are data acquisition speed and use of a common instrument. Disadvantages are reduced sampling interval, uncertainty of tangential position, and sagittal/tangential aspect ratio other than unity. Also, deep aspheric surfaces cannot be measured on a Fizeau interferometer without a specially made fringe nulling holographic plate. Other scanning instruments have been developed for measuring height, slope, or curvature profiles of the surface, but lack accuracy for very long scans required for X-ray synchrotron mirrors. The Long Trace Profiler (LTP) was developed specifically for long x-ray mirror measurement, and still outperforms other instruments, especially for aspheres. Thus, this paper focuses on error reduction techniques for the LTP.

  6. Measurement and analysis of active synchrotron mirrors under operating conditions

    Science.gov (United States)

    Sutter, John P.; Alcock, Simon G.; Sawhney, Kawal

    2013-05-01

    At the Diamond Light Source, in situ slope error measurements using the pencil-beam method have enabled X-ray mirror surfaces to be examined in their beamline environment. A surface corrugation common to several bimorph mirrors and the removal of that corrugation by repolishing were both confirmed using this method. In the same way, mirrors curved in a controlled way with bending actuators and sag compensators could also be optimized. Fits to the elastic bending of ideal beams using the Euler-Bernoulli model have been performed on the slope errors of a mechanically bent mirror in order to distinguish bender curvatures from gravitational distortion and to calculate the compensating force that most reduces the latter effect. A successful improvement of the sag compensation mechanism of a vertically focusing mirror was also achieved, aided by a previously tested method for optimizing the settings of a mirror's actuators using pencil-beam scans.

  7. Effects of electron temperature anisotropy on proton mirror instability evolution

    CERN Document Server

    Ahmadi, Narges; Raeder, Joachim

    2016-01-01

    Proton mirror modes are large amplitude nonpropagating structures frequently observed in the magnetosheath. It has been suggested that electron temperature anisotropy can enhance the proton mirror instability growth rate while leaving the proton cyclotron instability largely unaffected, therefore causing the proton mirror instability to dominate the proton cyclotron instability in Earth's magnetosheath. Here, we use particle-in-cell simulations to investigate the electron temperature anisotropy effects on proton mirror instability evolution. Contrary to the hypothesis, electron temperature anisotropy leads to excitement of the electron whistler instability. Our results show that the electron whistler instability grows much faster than the proton mirror instability and quickly consumes the electron free energy, so that there is no electron temperature anisotropy left to significantly impact the evolution of the proton mirror instability.

  8. IXO glass mirrors development in Europe

    Science.gov (United States)

    Pareschi, G.; Basso, S.; Bavdaz, M.; Citterio, O.; Civitani, M. M.; Conconi, P.; Gallieni, D.; Ghigo, M.; Martelli, F.; Parodi, G.; Proserpio, L.; Sironi, G.; Spiga, D.; Tagliaferri, G.; Tintori, M.; Wille, E.; Zambra, A.

    2011-09-01

    The mirrors of the International X-ray Observatory (IXO) were based on of a large number of high quality segments, aiming at achieving a global spatial resolution better than 5 arcsec (HEW). A study concerning the slumping of thin glass foils for the IXO mirrors is under development in Europe, funded by ESA and led by the Brera Observatory and is continuing even after that the programhas been descoped, in the perspective of using the technology under development for other future missions. After a preliminary trade-off study, we have focused our the effort on the "Direct" slumping approach, based on the use of convex moulds. In this case during the thermal cycle the optical surface of the glass is in direct contact with the mould surface. The thin plates are made of thin glass sheets (0.4 mm thick), with a reflecting area of 200 mm × 200 mm. The adopted integration process foresees the use of reinforcing ribs for bonding together the plates and forming in that way a rigid and stiff stack of segmented mirror shells; the stack is supported by a thick backplane. During the bonding process the plates are constrained to stay in close contact with the surface of the master (i.e. the same mould used for the hot slumping process) by the application of vacuum pump suction. In this way the spring-back deformations and low frequency errors still present on the foil profile after slumping can be corrected. In this paper we will give an overview and a status report of the project.

  9. Orbifolded Konishi from the mirror TBA

    Energy Technology Data Exchange (ETDEWEB)

    De Leeuw, Marius [Max-Planck-Institut fuer Gravitationsphysik, Albert-Einstein-Institute, Am Muehlenberg 1, 14476 Potsdam (Germany); Van Tongeren, Stijn J, E-mail: Marius.de.Leeuw@aei.mpg.de, E-mail: S.J.vanTongeren@uu.nl [Institute for Theoretical Physics and Spinoza Institute, Utrecht University, 3508 TD Utrecht (Netherlands)

    2011-08-12

    Starting with a discussion of the general applicability of the simplified mirror thermodynamic Bethe ansatz (TBA) equations to simple deformations of the AdS{sub 5} x S{sup 5} superstring, we proceed to study a specific type of orbifold to which the undeformed simplified TBA equations directly apply. We then use this set of equations, as well as Luescher's approach, to determine the next-to-leading-order wrapping correction to the energy of what we call the orbifolded Konishi state and show that they perfectly agree. In addition we discuss wrapping corrections to the ground-state energy of the orbifolded model under consideration.

  10. Weibel, Firehose and Mirror mode Relations

    CERN Document Server

    Treumann, R A

    2014-01-01

    Excitation of Weibel magnetic fields in an initially non-magnetized though anisotropic plasma may trigger other low-frequency instabilities fed by pressure anisotropy. It is shown that under Weibel-like-stable conditions the Weibel-like thermal fluctuation magnetic field allows for restricted Firehose-mode growth. In addition, low frequency Whistlers can also propagate in the plasma under certain anisotropic conditions. When the Weibel-like mode becomes unstable, Firehose instability ceases but Mirror modes take over. This will cause bubble structures in the Weibel-like field in addition to filamentation.

  11. Human mirror neuron system and its plasticity

    Institute of Scientific and Technical Information of China (English)

    Wei Chen; Tifei Yuan; Yin Wang; Jun Ding

    2008-01-01

    The mirror neuron system (MNS) was first discovered in non-human primates; these neurons fire when a monkey performs an action or observes another monkey (or even some people) performing that same action. Recent findings have suggested that neural rehabilitation might be achieved through the activation of the MNS in patients after stroke. We propose two major mechanisms (one involving adult neurogenesis and another involving brain-derived neurotrophic factor) that may underlie the activation, modulation and expe-rience-dependent plasticity in the MNS, for further study on promoting central nerve functional reconstruc-tion and rehabilitation of patients with central nervous system injury.

  12. Aberrations in Fresnel Lenses and Mirrors

    Science.gov (United States)

    Gregory, Don

    1999-01-01

    The NASA/MSFC Shooting Star program revealed a number of technical problems that must be solved before solar thermal propulsion can become a reality. The fundamental problem of interest here is the collection of solar energy. This is the first step in the propulsion process and indeed the most important. Everything else depends on the efficiency and focusing ability of the collection lens or mirror. An initial model of Fresnel lens behavior using a wave optics approach has been completed and the results were encouraging enough to warrant an experimental investigation. This experimental investigation confirmed some of the effects predicted and produced invaluable photographic evidence of coherence based diffraction and aberration.

  13. On the reflectivity of nickel neutron mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Adib, M.; Maayouf, R.M.A.; Abdel-Kawy, A.; Habib, N. (Atomic Energy Establishment, Cairo (Egypt). Reactor and Neutron Physics Dept.); Kenawy, M.A.; Wahba, M.; Ashry, A.H. (Ain Shams Univ., Cairo (Egypt))

    1991-02-01

    Neutron reflectivities were determined for 300 nm thick films of natural nickel and nickel 58 coated on glass plates. The measurements were performed at glancing angles between 40' and 60'. The incident neutron beam from one of the ET-RR-1 reactor horizontal channels covered neutron wavelengths between 0.55 and 0.80 nm. It was found that nickel 58, because of the high value of its critical glancing angle, is more efficient as a neutron mirror than natural nickel. (orig.).

  14. COMPASS mirror wall of RICH 1

    CERN Multimedia

    Patrice Loïez

    2001-01-01

    The COMPASS experiment uses ring imaging Cherenkov (RICH) counters to identify particles produced in high-energy muon collisions, to better understand the spin structure of the nucleon. Charged particles moving faster than the speed of light in the medium through which they are travelling emit a cone of Cherenkov radiation in the direction of their motion. The light in this cone is reflected from these mirrors onto a photo detector so that the size of the cone can be measured, which gives the energy of the particle.

  15. Closed-loop adaptive optical system with a liquid mirror.

    Science.gov (United States)

    Vdovin, Gleb

    2009-02-15

    A deformable mirror based on internal reflection from an electrostatically deformable liquid-air interface is proposed and investigated. A differential equation describing the static behavior of such a mirror is analyzed and solved numerically. Stable closed-loop operation of an adaptive optical system with a liquid deformable mirror is demonstrated, including forming and the correction of low-order aberrations described by Zernike polynomials and the real-time correction of dynamically changing aberrations.

  16. Ultra-lightweight mirror manufacturing and radiation response study

    Science.gov (United States)

    Fitzsimmons, T. C.; Crowe, D. A.

    1981-08-01

    The requirements for making ultra-lightweight mirrors of Ultra-Low Expansion (ULE) fused silica by frit bonding are investigated. A manufacturing assessment of the facilities needed to scale the mirror technology to 4 meters in diameter is included. A front surface flux loading thermal test of a.5M diameter frit bonded ULE mirror is also included. The test was supported by detailed modeling and analysis.

  17. Dynamical Casimir effect with $\\delta-\\delta^{\\prime}$ mirrors

    CERN Document Server

    Silva, Jeferson Danilo L; Alves, Danilo T

    2016-01-01

    We calculate the spectrum and the total rate of created particles for a real massless scalar field in $1+1$ dimensions, in the presence of a partially transparent moving mirror simulated by a Dirac $\\delta-\\delta^{\\prime}$ point interaction. We show that, strikingly, a partially reflecting mirror can produce a larger number of particles in comparison with a perfectly reflecting one. In the limit of a perfect mirror, our formulas recover those found in the literature for the Robin boundary condition.

  18. Ultra-Lightweight Mirror Manufacturing and Radiation Response Study

    Science.gov (United States)

    1981-08-01

    63 2.3.2-13 Absorptance and Spectral Radiance Versus Wavelength 0.5-Meter Mirror Coating irradiated by Tungsten Filament-Argon...was joined to an aluminum plate, 9 inches by 9 inches by 1.5 inches, using beeswax . The plate was drilled and tapped at the center to accommodate the...SECONDS the mirror was "* INCIDENT FLUX LEVEL ................. 𔃾.5 K4/N2 @ 68.8% COATING ABSORPTIVITY positioned ver- Ŕ FLUX UNIFORMITY OVER MIRROR

  19. Stitching interferometry for ellipsoidal x-ray mirrors.

    Science.gov (United States)

    Yumoto, Hirokatsu; Koyama, Takahisa; Matsuyama, Satoshi; Yamauchi, Kazuto; Ohashi, Haruhiko

    2016-05-01

    Ellipsoidal mirrors, which can efficiently produce a two-dimensional focusing beam with a single mirror, are superior x-ray focusing optics, especially when compared to elliptical-cylinder mirrors in the Kirkpatrick-Baez geometry. However, nano-focusing ellipsoidal mirrors are not commonly used for x-ray optics because achieving the accuracy required for the surface metrology of nano-focusing ellipsoidal mirrors is difficult due to their small radius of curvature along the short ellipsoidal axis. Here, we developed a surface metrology system for nano-focusing ellipsoidal mirrors using stitching interferometric techniques. The developed system simultaneously measures sub-aperture shapes with a microscopic interferometer and the tilt angles of the sub-aperture shapes with a large Fizeau interferometer. After correcting the systematic errors included in the sub-aperture shapes, the entire mirror shape is calculated by stitching the sub-aperture shapes based on the obtained relative angles between partially overlapped sub-apertures. In this study, we developed correction methods for systematic errors in sub-aperture shapes that originated from off-axis aberrations produced in the optics of the microscopic interferometer. The systematic errors on an ellipsoidal mirror were estimated by measuring a series of tilted plane substrates and the ellipsoidal substrate. From measurements of an ellipsoidal mirror with a 3.6-mm radius of curvature at the mirror center, we obtained a measurement repeatability of 0.51 nm (root-mean-square) in an assessment area of 0.5 mm × 99.18 mm. This value satisfies the requirements for surface metrology of nano-focusing x-ray mirrors. Thus, the developed metrology system should be applicable for fabricating nano-focusing ellipsoidal mirrors.

  20. Low-frequency Fresnel mirrors for fluorescence detectors

    Science.gov (United States)

    Diaz-Anzures, J.; Cordero-Davila, A.; Gonzalez-Garcia, J.; Martinez-Bravo, O.; Robledo-Sanchez, C.; Khrenov, B. A.; Garipov, G. K.

    2004-07-01

    In this work we present several designs of a Fresnel mirror with small number of rings (low frequency) to be used in fluorescence detectors aimed for study of ultra high energy cosmic rays. Being segmented the Fresnel mirror has an advantage of simple development from a compact package to a "plane" large area mirror-concentrator. This advantage is important for detectors in space and detectors at remote mountain sites. In this work, we investigated four possible ways of generating a focusing surface. In the first (main) design, the mirror consists of sections belonging to several parabolic surfaces. In this case the best focusing of a source on optical axis is achieved--the Fresnel mirror operates as parabolic mirror. This design is the best for a space "telescope", observing a source from large distances. Close to this design are mirror options with sections of a common parabolic surface and with sections of several spherical surfaces. The simplest for construction is the mirror with sections of a common spherical surface. In this design, focusing of a source on optical axis is much poorer than in previous options, but the mirror may be used in the experiments needed a wide field of view (FOV) with rough angular resolution. An advantage of this design is simplicity of the mirror construction which is shown in the mirror prototype construction and its testing. Results of the focal spot measurements are presented. This simple design of the Fresnel mirror is planned for use in the Pico de Orizaba mountain hybrid array where the wide field of view is important.

  1. The Physical Mirror Equivalence for the Local P^2

    CERN Document Server

    Cacciatori, Sergio Luigi; Guerra, Stefano

    2013-01-01

    In this paper we consider the total space of the canonical bundle of P^2 and we use a proposal by Hosono, together with results in Seidel and Auroux-Katzarkov-Orlov, to deduce the right physical mirror equivalence between D^b(K_{P^2}) and the derived Fukaya category of its mirror. By construction, our equivalence is compatible with the mirror map between moduli spaces and with the computation of Gromov--Witten invariants.

  2. Winter School on Mirror Symmetry, Vector Bundles and Lagrangian Submanifolds

    CERN Document Server

    Yau, S-T

    2002-01-01

    The collection of articles in this volume are based on lectures presented during the Winter School on Mirror Symmetry held at Harvard University. There are many new directions suggested by mirror symmetry which could potentially have very rich connections in physics and mathematics. This book brings together the latest research in a major area of mathematical physics, including the recent progress in mirror manifolds and Lagrangian submanifolds. In particular, several articles describing homological approach and related topics are included.

  3. Osteoblastic cell behavior on nanostructured metal implants.

    NARCIS (Netherlands)

    Guehennec, L Le; Martin, F.; Lopez-Heredia, M.A.; Louarn, G.; Amouriq, Y.; Cousty, J.; Layrolle, P.

    2008-01-01

    AIMS: Surface modifications at the nanometric scale may promote protein adsorption, cell adhesion and thus favor the osseointegration of metal implants. The behavior of osteoblastic cells was studied on mirror-polished (Smooth-SS) and nanostructured (Nano-SS) stainless steel surfaces. MATERIALS & ME

  4. Jane Eyre, a Historic Mirror%Jane Eyre,a Historic Mirror

    Institute of Scientific and Technical Information of China (English)

    王姝; 庄严

    2007-01-01

    Jane Eyre,a historic Mirror is from 3 aspects to illustrate the author's point of view in details, and the emphasis is according to the background of Victorian Age to express the society,the religion and the people's spiritual and physical life of that time.

  5. Verifying Mirror Technology for NGST with a Space-Qualified, Cryogenic 3.5 M Mirror

    CERN Document Server

    Angel, R P; Angel, Roger; Burge, Jim

    1998-01-01

    The lightweighting and surface accuracy targeted for NGST's 8 m primary mirror has been demonstrated in a 0.5 m prototype. Now a second, 2 m prototype weighing 40 kg in total is being fabricated at the University of Arizona under the NGST NMSD program. It will be tested in cryogenic operation in spring 1999. A third, advanced mirror system demonstrator (AMSD) is needed, the full size of an NGST segment, for flight qualification, including launch survival and extremely high reliability. The 3.5 m mirror, 1/6 the weight of HST's primary, would be made with a 2 mm thick glass face-sheet attached by adjustable screws to a carbon composite support. It would be figured as a fast telescope primary, and fully tested cryogenically to verify closed loop figure stability with simulated infrared starlight. If started in early 1999, this could be completed in 2001. Construction of the NGST mirror panels could then be undertaken on the basis of proven technology, and in time for a 2007 launch. With a diameter of 3.5 m and ...

  6. X-ray beam-shaping via deformable mirrors: analytical computation of the required mirror profile

    CERN Document Server

    Spiga, Daniele; Svetina, Cristian; Zangrando, Marco; 10.1016/j.nima.2012.10.117

    2013-01-01

    X-ray mirrors with high focusing performances are in use in both mirror mod- ules for X-ray telescopes and in synchrotron and FEL (Free Electron Laser) beamlines. A degradation of the focus sharpness arises in general from geo- metrical deformations and surface roughness, the former usually described by geometrical optics and the latter by physical optics. In general, technological developments are aimed at a very tight focusing, which requires the mirror profile to comply with the nominal shape as much as possible and to keep the roughness at a negligible level. However, a deliberate deformation of the mirror can be made to endow the focus with a desired size and distribution, via piezo actuators as done at the EIS-TIMEX beamline of FERMI@Elettra. The resulting profile can be characterized with a Long Trace Profilometer and correlated with the expected optical quality via a wavefront propagation code. However, if the roughness contribution can be neglected, the com- putation can be performed via a ray-tracin...

  7. Mirror system based therapy for autism spectrum disorders

    Institute of Scientific and Technical Information of China (English)

    Wei CHEN; Jing ZHANG; Jun DING

    2008-01-01

    This paper reviews the present theories and empirical research of autisms' cognitive research and mir-ror systems and introduces a new hypothesis about the causes of autism spectrum disorders (ASD): autistic mir-ror neuron dysfunction hypothesis. ASD subjects show obvious lack of the activation of the mirror system during the task of observation or emotional cognition. It is sig-nificant to investigate the mirror system for revealing the causes of autism and it is also helpful for developing new ways to diagnose or treat this disorder.

  8. Design of deformable mirrors for high power lasers

    Institute of Scientific and Technical Information of China (English)

    Stefano Bonora; Jan Pilar; Antonio Lucianetti; Tomas Mocek

    2016-01-01

    We present the workflow of the design, realization and testing of deformable mirrors suitable for high power diode pumped solid-state lasers. It starts with the study of the aberration to be corrected, and then it continues with the design of the actuators position and characteristic. In this paper, we present and compare three deformable mirrors realized for multi-J level laser facilities. We show that with the same design concept it is possible to realize deformable mirrors for other types of lasers. As an example, we report the realization of a deformable mirror for femtosecond lasers and for a CW CO2 laser.

  9. The use of mirror mechanism for activity-dependent neurorehabilitation

    Institute of Scientific and Technical Information of China (English)

    Jing Dong; Lei Song; Qun Liu; Ying Sha; Lina Lin; Yao Wang

    2011-01-01

    The present study observed the effects of the non-invasive, mirror neuron system application on neurorehabilitation.In primate studies, mirror neurons have been shown to fire when the subject observes or performs a specific action, thereby allowing for observation of motor cortex activation.This activation of the mirror neuron system could serve as a treatment for stroke patients.In the present study, the combination of a mirror neuron system-based therapy was introduced for the treatment of patients with motor-deficits, who could not perform rehabilitation exercises.The results also indicate that this therapeutic method plays a positive role in emotional regulation in the same patients.

  10. Relativistic Mean Field Study on Halo Structures of Mirror Nuclei

    Institute of Scientific and Technical Information of China (English)

    LIANG Yu-Jie; LI Yan-Song; LIU Zu-Hua; ZHOU Hong-Yu

    2009-01-01

    Halo structures of some light mirror nuclei are investigated with the relativistic mean field (RMF) theory.The calculations show that the dispersion of the valence proton is larger than that of the valence neutron in its mirror nucleus,the difference between the root-mean-square (rms) radius of the valence nucleon in each pair of mirror nuclei becomes smailer with the increase of the mass number A,and all the ratios of the rms radius of the valence nucleon to that of the matter in each pair o~ mirror nuclei decrease almost linearly with the increase of the mass number A.

  11. Low Cost, Light Weight Materials for Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed STTR is the combination of a small business with unique materials experience, and Northwestern Unviersity, with expertise in Mirror applications,...

  12. Advanced Actuator Concepts for High Precision Deformable Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — TRS Technologies proposes to develop a variety of single crystal actuators for adaptive optics deformable mirrors. Single crystal piezoelectric actuators are...

  13. Mirror neurons: Enigma of the metaphysical modular brain.

    Science.gov (United States)

    Acharya, Sourya; Shukla, Samarth

    2012-07-01

    Mirror neurons are one of the most important discoveries in the last decade of neuroscience. These are a variety of visuospatial neurons which indicate fundamentally about human social interaction. Essentially, mirror neurons respond to actions that we observe in others. The interesting part is that mirror neurons fire in the same way when we actually recreate that action ourselves. Apart from imitation, they are responsible for myriad of other sophisticated human behavior and thought processes. Defects in the mirror neuron system are being linked to disorders like autism. This review is a brief introduction to the neurons that shaped our civilization.

  14. Evidence of mirror neurons in human inferior frontal gyrus.

    Science.gov (United States)

    Kilner, James M; Neal, Alice; Weiskopf, Nikolaus; Friston, Karl J; Frith, Chris D

    2009-08-12

    There is much current debate about the existence of mirror neurons in humans. To identify mirror neurons in the inferior frontal gyrus (IFG) of humans, we used a repetition suppression paradigm while measuring neural activity with functional magnetic resonance imaging. Subjects either executed or observed a series of actions. Here we show that in the IFG, responses were suppressed both when an executed action was followed by the same rather than a different observed action and when an observed action was followed by the same rather than a different executed action. This pattern of responses is consistent with that predicted by mirror neurons and is evidence of mirror neurons in the human IFG.

  15. Development of light-weight spherical mirrors for RICH detectors

    CERN Document Server

    Metlica, Fabio

    2007-01-01

    Glass-coated beryllium and carbon-fiber light-weight spherical mirrors, with radii of curvature of $\\sim$ 2700mm, have been successfully developed and tested as part of the LHCb RICH experimental programme. The low mass mirror is necessary to minimize the amount of material within the LHCb spectrometer acceptance, with a requirement of less than 2% of a radiation length. Both technologies are suitable for light-weight mirror applications. The R&D and characterization of the mirrors are reported.

  16. Large Scale Cleaning Telescope Mirrors with Electron Beams Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Cleaning Lenses and Mirrored Surfaces with Electrons tasks include: Development of Fractal Wand Geometries; Vacuum Chamber testing for Fractal Wand Prototypes;...

  17. Silicon Carbide Corrugated Mirrors for Space Telescopes Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Trex Enterprises Corporation (Trex) proposes technology development to manufacture monolithic, lightweight silicon carbide corrugated mirrors (SCCM) suitable for...

  18. Mirror alignment control for COMPASS RICH-1 detector

    Energy Technology Data Exchange (ETDEWEB)

    Alexeev, M. [INFN, Sezione di Torino and University of East Piemonte, Alessandria (Italy); Birsa, R. [INFN, Sezione di Trieste, Trieste (Italy); Bradamante, F.; Bressan, A. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy); Chiosso, M. [INFN, Sezione di Torino and University of Torino, Torino (Italy); Ciliberti, P. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy); Dalla Torre, S. [INFN, Sezione di Trieste, Trieste (Italy); Denisov, O. [INFN, Sezione di Torino, Torino (Italy); Duic, V. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy); Ferrero, A. [INFN, Sezione di Torino and University of Torino, Torino (Italy); Finger, M.; Finger, M. [Charles University, Praga (Czech Republic); JINR, Dubna (Russian Federation); Giorgi, M. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy); Gobbo, B. [INFN, Sezione di Trieste, Trieste (Italy); Levorato, S. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy); Maggiora, A. [INFN, Sezione di Torino, Torino (Italy); Martin, A. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy); Menon, G. [INFN, Sezione di Trieste, Trieste (Italy); Panzieri, D. [INFN, Sezione di Torino and University of East Piemonte, Alessandria (Italy); Pesaro, G. [INFN, Sezione di Trieste and University of Trieste, Trieste (Italy)

    2011-05-21

    The focusing system of the COMPASS RICH-1 detector consists of two segmented spherical mirror surfaces, formed by 68 hexagonal and 48 pentagonal individual elements. All individual mirrors have two degrees of freedom to adjust the angular alignment in order to obtain a continuous spherical surface. Relative angular misalignments can be monitored on-line by the CLAM method, based on the optical reconstruction of line images. Complementing the CLAM measurements with photogrammetry, the absolute mirror orientation and position in space can be determined too. The method is described, as well as the algorithms used to access the relative and absolute mirror alignment.

  19. System Estimates Radius of Curvature of a Segmented Mirror

    Science.gov (United States)

    Rakoczy, John

    2008-01-01

    A system that estimates the global radius of curvature (GRoC) of a segmented telescope mirror has been developed for use as one of the subsystems of a larger system that exerts precise control over the displacements of the mirror segments. This GRoC-estimating system, when integrated into the overall control system along with a mirror-segment- actuation subsystem and edge sensors (sensors that measure displacements at selected points on the edges of the segments), makes it possible to control the GROC mirror-deformation mode, to which mode contemporary edge sensors are insufficiently sensitive. This system thus makes it possible to control the GRoC of the mirror with sufficient precision to obtain the best possible image quality and/or to impose a required wavefront correction on incoming or outgoing light. In its mathematical aspect, the system utilizes all the information available from the edge-sensor subsystem in a unique manner that yields estimates of all the states of the segmented mirror. The system does this by exploiting a special set of mirror boundary conditions and mirror influence functions in such a way as to sense displacements in degrees of freedom that would otherwise be unobservable by means of an edge-sensor subsystem, all without need to augment the edge-sensor system with additional metrological hardware. Moreover, the accuracy of the estimates increases with the number of mirror segments.

  20. Robotic Mirror Therapy System for Functional Recovery of Hemiplegic Arms.

    Science.gov (United States)

    Beom, Jaewon; Koh, Sukgyu; Nam, Hyung Seok; Kim, Wonshik; Kim, Yoonjae; Seo, Han Gil; Oh, Byung-Mo; Chung, Sun Gun; Kim, Sungwan

    2016-08-15

    Mirror therapy has been performed as effective occupational therapy in a clinical setting for functional recovery of a hemiplegic arm after stroke. It is conducted by eliciting an illusion through use of a mirror as if the hemiplegic arm is moving in real-time while moving the healthy arm. It can facilitate brain neuroplasticity through activation of the sensorimotor cortex. However, conventional mirror therapy has a critical limitation in that the hemiplegic arm is not actually moving. Thus, we developed a real-time 2-axis mirror robot system as a simple add-on module for conventional mirror therapy using a closed feedback mechanism, which enables real-time movement of the hemiplegic arm. We used 3 Attitude and Heading Reference System sensors, 2 brushless DC motors for elbow and wrist joints, and exoskeletal frames. In a feasibility study on 6 healthy subjects, robotic mirror therapy was safe and feasible. We further selected tasks useful for activities of daily living training through feedback from rehabilitation doctors. A chronic stroke patient showed improvement in the Fugl-Meyer assessment scale and elbow flexor spasticity after a 2-week application of the mirror robot system. Robotic mirror therapy may enhance proprioceptive input to the sensory cortex, which is considered to be important in neuroplasticity and functional recovery of hemiplegic arms. The mirror robot system presented herein can be easily developed and utilized effectively to advance occupational therapy.

  1. Evolution of the mirror approach to fusion: some conjectures

    Energy Technology Data Exchange (ETDEWEB)

    Post, R.E.

    1984-09-18

    Some possible directions for the future evolution of the mirror approach to fusion are outlined, in the context of economically-motivated criteria. Speculations are given as to the potential advantages, economic and otherwise, of the use of axially-symmetric systems, operated in semi-collisional regimes of lower Q (fusion power balance ratio) than that projected for present-day tandem mirror designs. These regims include barely tandem modes, and ion-heated modes, in association with higher efficiency direct conversion. Another possible economically advantageous approach mentioned is the use of a tandem mirror plasma to stabilize a FRM (field-reversed mirror) plasma, with potential synergistic advantages.

  2. Optical systems for synchrotron radiation. Lecture 2. Mirror systems

    Energy Technology Data Exchange (ETDEWEB)

    Howells, M.R.

    1986-02-01

    The process of reflection of VUV and x-radiation is summarized. The functions of mirrors in synchrotron beamlines are described, which include deflection, filtration, power absorption, formation of a real image, focusing, and collimation. Fabrication of optical surfaces for synchrotron radiation beamlines are described, and include polishing of a near spherical surface as well as bending a cylindrical surface to toroidal shape. The imperfections present in mirrors, aberrations and surface figure inaccuracy, are discussed. Calculation of the thermal load of a mirror in a synchrotron radiation beam and the cooling of the mirror are covered briefly. 50 refs., 7 figs. (LEW)

  3. Elliptically Bent X-ray Mirrors with Active Temperature Stabilization

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Sheng; Church, Matthew; Yashchuk, Valeriy V.; Goldberg, Kenneth A.; Celestre, Rich; McKinney, Wayne R.; Kirschman, Jonathan; Morrison, Greg; Noll, Tino; Warwick, Tony; Padmore, Howard A.

    2010-01-31

    We present details of design of elliptically bent Kirkpatrick-Baez mirrors developed and successfully used at the Advanced Light Source for submicron focusing. A distinctive feature of the mirror design is an active temperature stabilization based on a Peltier element attached directly to the mirror body. The design and materials have been carefully optimized to provide high heat conductance between the mirror body and substrate. We describe the experimental procedures used when assembling and precisely shaping the mirrors, with special attention paid to laboratory testing of the mirror-temperature stabilization. For this purpose, the temperature dependence of the surface slope profile of a specially fabricated test mirror placed inside a temperature-controlled container was measured. We demonstrate that with active mirror-temperature stabilization, a change of the surrounding temperature by more than 3K does not noticeably affect the mirror figure. Without temperature stabilization, the surface slope changes by approximately 1.5 ?mu rad rms (primarily defocus) under the same conditions.

  4. Assessment of MODIS Scan Mirror Reflectance Changes On-Orbit

    Science.gov (United States)

    Xiong, Xiaoxiong; Wu, A.; Angal, A.

    2008-01-01

    Since launch, the NASA EOS Terra and Aqua MODIS have operated successfully for more than 8 and 6 years, respectively. MODIS collects data using a two-sided scan mirror over a large scan angular range. The scan mirror is made of a polished, nickel-plated beryllium base coated with high purity silver, which is then over-coated with the Denton proprietary silicon monoxide and silicon dioxide mixture. The scan mirror's reflectance was characterized pre-launch using its witness samples, and the response versus scan angle was measured at the sensor system level. In this study, we present an assessment of MODIS scan mirror on-orbit degradation by examining changes of spectral band response over each sensor's mission lifetime. Results show that the scan mirror's optical properties for both Terra and Aqua MODIS have experienced significant degradation since launch in the VIS spectral region, which is mirror side dependent as well as scan angle dependent. In general, the mirror degradation is more severe for Terra MODIS than Aqua MODIS, especially during recent years. For Terra MODIS, the degradation rate is noticeably different between the mirror sides. On the other hand, there has been little mirror side dependent difference for Aqua MODIS.

  5. The ontogenetic origins of mirror neurons: evidence from ‘tool-use’ and ‘audiovisual’ mirror neurons

    Science.gov (United States)

    Cook, Richard

    2012-01-01

    Since their discovery, mirror neurons—units in the macaque brain that discharge both during action observation and execution—have attracted considerable interest. Whether mirror neurons are an innate endowment or acquire their sensorimotor matching properties ontogenetically has been the subject of intense debate. It is widely believed that these units are an innate trait; that we are born with a set of mature mirror neurons because their matching properties conveyed upon our ancestors an evolutionary advantage. However, an alternative view is that mirror neurons acquire their matching properties during ontogeny, through correlated experience of observing and performing actions. The present article re-examines frequently overlooked neurophysiological reports of ‘tool-use’ and ‘audiovisual’ mirror neurons within the context of this debate. It is argued that these findings represent compelling evidence that mirror neurons are a product of sensorimotor experience, and not an innate endowment. PMID:22573832

  6. A Research on the Primary Mirror Manipulator of Large Segmented-mirror Telescope

    Science.gov (United States)

    Zuo, H.

    2012-09-01

    Since Galileo firstly used the telescope to observe the sky 400 years ago, the aperture of the telescope has become larger and larger to observe the deeper universe, and the segmented-mirror telescope is becoming more and more popular with increasing aperture. In the early 21st century, a series of segmented-mirror telescopes have been constructed including the Large Sky Area Multi-object Fiber Spectroscopic Telescope (LAMOST) of China. LAMOST is a meridian reflecting Schmidt telescope, and the dimension of the primary mirror is about 6.7 m× 6 m, which is composed of 37 hexagonal sub-mirrors. However, a problem about the mirror installation appears with the increasing aperture. If there are hundreds of sub-mirrors in the telescope, it is a challenging job to mount and dismount them to the truss. This problem is discussed in this paper and a manipulator for the primary mirror of LAMOST is designed to perform the mount and dismount work. In chapter 1, all the segmented-mirror telescopes in the world are introduced and how the sub-mirrors of these telescopes are installed has been investigated. After comparing with the serial and the parallel robot, a serial robot manipulator proposal, which has several redundant degrees of freedom (DOFs), has been chosen from a series of design proposals. In chapter 2, the theoretical analysis has been carried out on the basis of the design proposal, which includes the forward kinematics and the inverse kinematics. Firstly the D-H coordinate is built according to the structure of the manipulator, so it is possible to obtain the end-effector position and orientation from the individual joint motion thanks to the forward kinematics. Because of the redundant DOFs of the manipulator, the inverse kinematics solution can be a very trick task, and the result may not be only, therefore a kind of simulation is carried out to get the numerical solution using ADAMS (Automatic Dynamic Analysis of Mechanical System). In the dynamics analysis the

  7. Soiling and degradation analysis of solar mirrors

    Science.gov (United States)

    Delord, Christine; Blaise, Anthony; Fernandez-García, Aránzazu; Martínez-Arcos, Lucía; Sutter, Florian; Reche-Navarro, Tomás Jesús

    2016-05-01

    The degradation and the soiling of the mirrors are dependent of the solar field and the mirrors technologies, the local climate, the meteorological events, the O&M tasks and the human activities around the site. In the frame of the European project SFERA II, the SODAM project has been the opportunity to compare the soiling and the degradation mechanisms on a Fresnel solar field installed in the South of France and on a parabolic-through solar field installed in the South of Spain. The analysis of the soiling has shown equivalent maximum weekly reflectance loss due to soiling in both sites but a double mean weekly reflectance loss in Spain respect to France, as well as typical meteorological events to be taken into account to adapt the cleaning strategies. Among the meteorological parameters mainly influencing the soiling, the study has revealed the effect of the rain and of the DNI. In parallel, the analysis of the degradation mechanisms has highlighted a common chalking of the protective back paint layers due to the irradiation. This chalking being associated to a leaching of the paint layers in the site of Cadarache due to the high presence of liquid water. A difference in the speed of corrosion of the silver layer has been also noticed, leading to a difference in the mechanisms of delamination of the paints layers.

  8. Euclid mirrors and test collimator: AMOS developments

    Science.gov (United States)

    Gloesener, Pierre; Wolfs, Fabrice; Cola, Marcel; Pirnay, Olivier; Flebus, Carlo

    2016-07-01

    EUCLID is an optical/near-infrared survey mission to be launched in 2020 towards the L2 Lagrange point. It will aim at studying the dark universe and providing a better understanding of the origin of the accelerating expansion of the universe. Through the use of cosmological sounding, it will investigate the nature of dark energy, dark matter and gravity by tracking their observational signatures on the geometry of the universe and on the cosmic history of large structures formation. The EUCLID payload module (PLM) consists of a 1.2 m-class telescope and will accommodate two instruments. As a subcontractor of AIRBUS Defence and Space, AMOS is responsible for the manufacturing of the secondary and the third mirrors of the telescope as well as for the flat folding mirror set within the focal plane arrangement of EUCLID telescope, which incorporates dedicated filtering functions. AMOS produces in addition the 1.3 m-class test collimator for the on-ground validation of the EUCLID instrument.

  9. Advances in very lightweight composite mirror technology

    Science.gov (United States)

    Chen, Peter C.; Bowers, Charles W.; Content, David A.; Marzouk, Marzouk; Romeo, Robert C.

    2000-09-01

    We report progress in the development of very lightweight (roll off and several waves (rms optical) of astigmatism, coma, and third-order spherical aberration. These are indications of thermal contraction in an inhomogeneous medium. This inhomogeneity is due to a systematic radial variation in density and fiber/resin ratio induced in composite plies when draped around a small and highly curved mandrel. The figure accuracy is expected to improve with larger size optics and in mirrors with longer radii of curvature. Nevertheless, the present accuracy figure is sufficient for using postfiguring techniques such as ion milling to achieve diffraction-limited performances at optical and UV wavelengths. We demonstrate active figure control using a simple apparatus of low-mass, low-force actuators to correct astigmatism. The optimized replication technique is applied to the fabrication of a 0.6-m-diam mirror with an areal density of 3.2 kg/m2. Our result demonstrates that the very lightweight, large-aperture construction used in radio telescopes can now be applied to optical telescopes.

  10. EUV testing of multilayer mirrors: critical issues

    Energy Technology Data Exchange (ETDEWEB)

    Hill, S B; Ermanoski, I; Grantham, S; Tarrio, C; Lucatorto, T B; Madey, T E; Bajt, S; Chandhok, M; Yan, P; Wood, O; Wurn, S; Edwards, N V

    2006-02-24

    Recently, while performing extensive EUV irradiation endurance testing on Ru-capped multilayer mirrors in the presence of elevated partial pressures of water and hydrocarbons, NIST has observed that the amount of EUV-induced damage actually decreases with increasing levels of water vapor above {approx} 5 x 10{sup -7} Torr. It is thought that the admitted water vapor may interact with otherwise stable, condensed carbonaceous species in an UHV vacuum system to increase the background levels of simple gaseous carbon-containing molecules. Some support for this hypothesis was demonstrated by observing the mitigating effect of very small levels of simple hydrocarbons with the intentional introduction of methyl alcohol in addition to the water vapor. It was found that the damage rate decreased by at least an order of magnitude when the partial pressure of methyl alcohol was just one percent of the water partial pressure. These observations indicate that the hydrocarbon components of the vacuum environment under actual testing conditions must be characterized and controlled to 10{sup -11} Torr or better in order to quantify the damage caused by high levels of water vapor. The possible effects of exposure beam size and out-of-band radiation on mirror lifetime testing will also be discussed.

  11. Roughness tolerances for Cherenkov telescope mirrors

    CERN Document Server

    Tayabaly, K; Canestrari, R; Bonnoli, G; Lavagna, M; Pareschi, G

    2016-01-01

    The Cherenkov Telescope Array (CTA) is a forthcoming international ground-based observatory for very high-energy gamma rays. Its goal is to reach sensitivity five to ten times better than existing Cherenkov telescopes such as VERITAS, H.E.S.S. or MAGIC and extend the range of observation to energies down to few tens of GeV and beyond 100 TeV. To achieve this goal, an array of about 100 telescopes is required, meaning a total reflective surface of several thousands of square meters. Thence, the optimal technology used for CTA mirrors manufacture should be both low-cost (~1000 euros/m2) and allow high optical performances over the 300-550 nm wavelength range. More exactly, a reflectivity higher than 85% and a PSF (Point Spread Function) diameter smaller than 1 mrad. Surface roughness can significantly contribute to PSF broadening and limit telescope performances. Fortunately, manufacturing techniques for mirrors are now available to keep the optical scattering well below the geometrically-predictable effect of ...

  12. Plasma Control in Symmetric Mirror Machines

    Science.gov (United States)

    Horton, W.; Rowan, W. L.; Alvarado, Igor; Fu, X. R.; Beklemishev, A. D.

    2014-10-01

    Plasma confinement in the symmetric rotating mirror plasma at the Budker Institute shows enhanced confinement with high electron temperatures with end plates biasing. Improved confinement is achieved by biasing end plate cells in the expansion tanks so as to achieve an inward pointing radial electric field. The negative potential well produces vortex plasma rotation similar to that in the negative potential well of Ohmic heated tokamaks. This plasma state has similarity with the lower turbulence level regimes documented in the Helimak where negative biasing of the end plates produces an inward radial electric field. To understand this vortex confinement we carry out 3D simulations with nonlinear partial differential equations for the electric potential and density in plasmas with an axially localized region of unfavorable and favorable magnetic curvature. The simulations show that the plasma density rapidly adjusts to be higher in the region of favorable curvature regions and remains relatively well confined while rapidly rotating. The results support the concept of using plasma-biasing electrodes in large expander tanks to achieve enhanced mirror plasma confinement. Supported by US-DoE grant to UT, LANL and the Budker Institute for Nuclear Physics.

  13. Development of a miniaturized deformable mirror controller

    Science.gov (United States)

    Bendek, Eduardo; Lynch, Dana; Pluzhnik, Eugene; Belikov, Ruslan; Klamm, Benjamin; Hyde, Elizabeth; Mumm, Katherine

    2016-07-01

    High-Performance Adaptive Optics systems are rapidly spreading as useful applications in the fields of astronomy, ophthalmology, and telecommunications. This technology is critical to enable coronagraphic direct imaging of exoplanets utilized in ground-based telescopes and future space missions such as WFIRST, EXO-C, HabEx, and LUVOIR. We have developed a miniaturized Deformable Mirror controller to enable active optics on small space imaging mission. The system is based on the Boston Micromachines Corporation Kilo-DM, which is one of the most widespread DMs on the market. The system has three main components: The Deformable Mirror, the Driving Electronics, and the Mechanical and Heat management. The system is designed to be extremely compact and have lowpower consumption to enable its use not only on exoplanet missions, but also in a wide-range of applications that require precision optical systems, such as direct line-of-sight laser communications, and guidance systems. The controller is capable of handling 1,024 actuators with 220V maximum dynamic range, 16bit resolution, and 14bit accuracy, and operating at up to 1kHz frequency. The system fits in a 10x10x5cm volume, weighs less than 0.5kg, and consumes less than 8W. We have developed a turnkey solution reducing the risk for currently planned as well as future missions, lowering their cost by significantly reducing volume, weight and power consumption of the wavefront control hardware.

  14. Do mirror glasses have the same effect on brain activity as a mirror box? Evidence from a functional magnetic resonance imaging study with healthy subjects.

    Science.gov (United States)

    Milde, Christopher; Rance, Mariela; Kirsch, Pinar; Trojan, Jörg; Fuchs, Xaver; Foell, Jens; Bekrater-Bodmann, Robin; Flor, Herta; Diers, Martin

    2015-01-01

    Since its original proposal, mirror therapy has been established as a successful neurorehabilitative intervention in several neurological disorders to recover motor function or to relieve pain. Mirror therapy seems to operate by reactivating the contralesional representation of the non-mirrored limb in primary motor- and somatosensory cortex. However, mirror boxes have some limitations which prompted the use of additional mirror visual feedback devices. The present study evaluated the utility of mirror glasses compared to a mirror box. We also tested the hypothesis that increased interhemispheric communication between the motor hand areas is the mechanism by which mirror visual feedback recruits the representation of the non-mirrored limb. Therefore, mirror illusion capacity and brain activations were measured in a within-subject design during both mirror visual feedback conditions in counterbalanced order with 20 healthy subjects inside a magnetic resonance imaging scanner. Furthermore, we analyzed task-dependent functional connectivity between motor hand representations using psychophysiological interaction analysis during both mirror tasks. Neither the subjective quality of mirror illusions nor the patterns of functional brain activation differed between the mirror tasks. The sensorimotor representation of the non-mirrored hand was recruited in both mirror tasks. However, a significant increase in interhemispheric connectivity between the hand areas was only observed in the mirror glasses condition, suggesting different mechanisms for the recruitment of the representation of the non-mirrored hand in the two mirror tasks. We conclude that the mirror glasses might be a promising alternative to the mirror box, as they induce similar patterns of brain activation. Moreover, the mirror glasses can be easy applied in therapy and research. We want to emphasize that the neuronal mechanisms for the recruitment of the affected limb representation might differ depending on

  15. Durable silver mirror with ultra-violet thru far infra-red reflection

    Science.gov (United States)

    Wolfe, Jesse D.

    2010-11-23

    A durable highly reflective silver mirror characterized by high reflectance in a broad spectral range of about 300 nm in the UV to the far infrared (.about.10000 nm), as well as exceptional environmental durability. A high absorptivity metal underlayer is used which prevents the formation of a galvanic cell with a silver layer while increasing the reflectance of the silver layer. Environmentally durable overcoat layers are provided to enhance mechanical and chemical durability and protect the silver layer from corrosion and tarnishing, for use in a wide variety of surroundings or climates, including harsh or extreme environments.

  16. Durable silver mirror with ultra-violet thru far infra-red reflection

    Energy Technology Data Exchange (ETDEWEB)

    Wolfe, Jesse D. (Discovery Bay, CA)

    2010-11-23

    A durable highly reflective silver mirror characterized by high reflectance in a broad spectral range of about 300 nm in the UV to the far infrared (.about.10000 nm), as well as exceptional environmental durability. A high absorptivity metal underlayer is used which prevents the formation of a galvanic cell with a silver layer while increasing the reflectance of the silver layer. Environmentally durable overcoat layers are provided to enhance mechanical and chemical durability and protect the silver layer from corrosion and tarnishing, for use in a wide variety of surroundings or climates, including harsh or extreme environments.

  17. A phenomenological model of coating/substrate adhesion and interfacial bimetallic peeling stress in composite mirrors

    Science.gov (United States)

    Mcelroy, Paul M.; Lawson, Daniel D.

    1990-01-01

    Adhesion and interfacial stress between metal films and structural composite material substrates is discussed. A theoretical and conceptual basis for selecting coating materials for composite mirror substrates is described. A phenomenological model that interrelates cohesive tensile strength of thin film coatings and interfacial peeling stresses is presented. The model serves as a basis in determining gradiated materials response and compatibility of composite substrate and coating combinations. Parametric evaluation of material properties and geometrical factors such as coating thickness are used to determine the threshold stress levels for maintaining adhesion at the different interfaces.

  18. A generalized electrostatic micro-mirror (GEM) model for a two-axis convex piecewise linear shaped MEMS mirror

    Science.gov (United States)

    Edwards, C. L.; Edwards, M. L.

    2009-05-01

    MEMS micro-mirror technology offers the opportunity to replace larger optical actuators with smaller, faster ones for lidar, network switching, and other beam steering applications. Recent developments in modeling and simulation of MEMS two-axis (tip-tilt) mirrors have resulted in closed-form solutions that are expressed in terms of physical, electrical and environmental parameters related to the MEMS device. The closed-form analytical expressions enable dynamic time-domain simulations without excessive computational overhead and are referred to as the Micro-mirror Pointing Model (MPM). Additionally, these first-principle models have been experimentally validated with in-situ static, dynamic, and stochastic measurements illustrating their reliability. These models have assumed that the mirror has a rectangular shape. Because the corners can limit the dynamic operation of a rectangular mirror, it is desirable to shape the mirror, e.g., mitering the corners. Presented in this paper is the formulation of a generalized electrostatic micromirror (GEM) model with an arbitrary convex piecewise linear shape that is readily implemented in MATLAB and SIMULINK for steady-state and dynamic simulations. Additionally, such a model permits an arbitrary shaped mirror to be approximated as a series of linearly tapered segments. Previously, "effective area" arguments were used to model a non-rectangular shaped mirror with an equivalent rectangular one. The GEM model shows the limitations of this approach and provides a pre-fabrication tool for designing mirror shapes.

  19. ORAL ISSUE OF THE JOURNAL "USPEKHI FIZICHESKIKH NAUK": Mirror particles and mirror matter: 50 years of speculation and searching

    Science.gov (United States)

    Okun', Lev B.

    2007-04-01

    This review describes the history of the discovery of the violation of the spatial parity P, the charge conjugation parity C, and the combined parity CP. The hypothesis of the existence of mirror particles was intended by its authors to restore the symmetry between left and right. The review presents the emergence and evolution of the concepts of 'mirror particles' and 'mirror matter' and can serve as a concise travel guide to 'mirror land.' An important part of the review is the list of about 200 references with their titles.

  20. Mirror-image anterior crown fabrication with computer-aided design and rapid prototyping technology: a clinical report.

    Science.gov (United States)

    Cho, Seok-Hwan; Chang, Won-Gun

    2013-02-01

    This clinical report describes the fabrication of a maxillary central incisor single crown with rapid prototyping (RP) technology. A patient with a recently replaced metal ceramic crown had discomfort due to the nonanatomic lingual contour of the crown. With computer-aided design (CAD) software and rapid prototyping (RP) technology, the shape of the contralateral central incisor was duplicated and reproduced to make a mirror-image for a new crown. The prosthodontic planning and treatment approach are discussed.