WorldWideScience

Sample records for super lightweight external

  1. HST Super Lightweight Interchangeable Carrier (SLIC) Static Test

    Science.gov (United States)

    Chambers, William V.

    2008-01-01

    The HST Super Light Weight Interchangeable Carrier Static Test program calls for a total of 15 load cases with an average of 9 simultaneous push/pull locations per load case. This testing program represents the most complex static test ever attempted at Goddard Space Flight Center. Many unique multi-pull fixtures were designed to apply the simultaneous loading. Additionally, a total of 600 channels of data required processing for each loadcase. A total of 1100 separate strain gages were installed on SLIC. A team of 15 trained technicians were needed to apply test loads via mechanical hand pumps for several load cases. All 15 load cases were successfully conducted within 15 weeks. The ManTech team successfully tested all SLIC 1200 interface clips to the required testing loads. Several unique designs were needed to address testing challenges as loadline interference, Payload Safety, payload flexibility and opposing load applications.

  2. Super flame-retardant lightweight rime-like carbon-phenolic nanofoam

    Science.gov (United States)

    Cheng, Haiming; Hong, Changqing; Zhang, Xinghong; Xue, Huafei; Meng, Songhe; Han, Jiecai

    2016-09-01

    The desire for lightweight nanoporous materials with high-performance thermal insulation and efficient anti-ablation resistance for energy conservation and thermal protection/insulation has greatly motivated research and development recently. The main challenge to synthesize such lightweight materials is how to balance the relationship of low thermal conductivity and flame retardancy. Herein, we propose a new concept of lightweight “rime-like” structured carbon-phenolic nanocomposites to solve this problem, where the 3D chopped network-structured carbon fiber (NCF) monoliths are incorporated with nanoporous phenolic aerogel to retain structural and functional integrity. The nanometer-scaled porous phenolic (NP) was synthesized through polymerization-induced phase separation and ambient pressure drying using phenolic resin (PR) solution as reaction source, ethylene glycol (EG) as solvent and hexamethylenetetramine (HMTA) as catalyst. We demonstrate that the as-prepared NCF-NP nanocomposite exhibits with a low density of 0.25–0.35 g/cm3, low thermal conductivity of 0.125 Wm‑1K‑1 and outstanding flame retardancy exceeding 2000 °C under arc-jet wind tunnel simulation environment. Our results show that the synthesis strategy is a promising approach for producing nanocomposites with excellent high-temperature heat blocking property.

  3. Ultra lightweight PMMA-based composite plates with robust super-hydrophobic surfaces.

    Science.gov (United States)

    Pareo, Paola; De Gregorio, Gian Luca; Manca, Michele; Pianesi, Maria Savina; De Marco, Luisa; Cavallaro, Francesco; Mari, Margherita; Pappadà, Silvio; Ciccarella, Giuseppe; Gigli, Giuseppe

    2011-11-15

    Extremely lightweight plates made of an engineered PMMA-based composite material loaded with hollow glass micro-sized spheres, nano-sized silica particles and aluminum hydroxide prismatic micro-flakes were realized by cast molding. Their interesting bulk mechanical properties were combined to properly tailored surface topography compatible with the achievement of a superhydrophobic behavior after the deposition of a specifically designed hydrophobic coating. With this aim, we synthesized two different species of fluoromethacrylic polymers functionalized with methoxysilane anchoring groups to be covalently grafted onto the surface protruding inorganic fillers. By modulating the feed composition of the reacting monomers, it was possible to combine the hydrophobic character of the polymer with an high adhesion strength to the substrate and hence to maximize both the water contact angle (up to 157°) and the durability of the easy-to-clean effect (up to 2000 h long outdoor exposure).

  4. Lightweight concrete blocks with EVA recycled aggregate: a contribution to the thermal efficiency of building external walls

    Directory of Open Access Journals (Sweden)

    De Melo, A. B.

    2013-12-01

    Full Text Available The regions with lots of shoe production suffer environmental impacts from waste generation during manufacturing of insoles and outsoles. Research conducted in Brazil has demonstrated the technical feasibility to recycle these wastes, especially Ethylene Vinyl Acetate (EVA, as lightweight aggregate, in the production of non-structural cement blocks. This article presents an evaluation of thermal performance with measurements of temperature variation in mini walls (1 m2 built with different materials, including various kinds of EVA block and ceramic bricks. Tests have shown efficient thermal performance for masonry blocks with EVA. These results and supplementary estimates contribute to add value to the EVA block, considering that there are good expectations that the component, with the new geometry proposed, can contribute to the energy efficiency of buildings, highlighting its suitability to most Brazilian bioclimatic regions.Las regiones con una gran producción de calzado sufren impactos ambientales derivados de la generación de residuos durante la producción de plantillas y suelas. Investigaciones realizadas en Brasil han demostrado la viabilidad técnica para el reciclaje de estos residuos, especialmente el Etileno Vinil Acetato (EVA, como agregado ligero en la fabricación de bloques de hormigón no estructurales. Este trabajo presenta una evaluación del rendimiento térmico, con mediciones de la variación de la temperatura en pequeñas paredes (1 m2 construidas con diversos materiales, incluyendo algunos tipos de bloques EVA y ladrillos de cerámica. Las pruebas demostraron actuaciones térmicas eficientes para las muestras con bloques EVA. Estos resultados y cálculos adicionales contribuyen con un aporte de valor añadido al bloque EVA, considerando que existen buenas expectativas del componente, con una nueva propuesta de geometría, pudiendo contribuir a la eficiencia energética de edificios, especialmente por su adecuación a la

  5. Vibration, acoustic, and shock design and test criteria for components on the Solid Rocket Boosters (SRB), Lightweight External Tank (LWT), and Space Shuttle Main Engines (SSME)

    Science.gov (United States)

    1984-01-01

    The vibration, acoustics, and shock design and test criteria for components and subassemblies on the space shuttle solid rocket booster (SRB), lightweight tank (LWT), and main engines (SSME) are presented. Specifications for transportation, handling, and acceptance testing are also provided.

  6. Lightweight Structures.

    Science.gov (United States)

    Shaver and Co., Michigan City, IN.

    One of the newest and most promising developments in architecture has been the use of lightweight structures for encapsulating space. Using this new technology, builders can enclose large and small areas at a fraction of the cost of conventional construction and at the same time provide interior space that is totally flexible. This brochure shows…

  7. 轻质砂浆复合聚氨酯板外墙外保温系统施工技术∗%Construction Technology of External Thermal Insulation System Based on Lightweight Mortar Composite with Rigid Polyurethane Foam Board

    Institute of Scientific and Technical Information of China (English)

    孙桂芳; 王永魁; 罗淑湘; 邱军付

    2014-01-01

    硬泡聚氨酯复合板是近两年发展形成的一种新型保温板材,该板材采用薄抹灰外墙外保温系统,许多工程应用后出现了板框可见、板缝裂缝等质量问题,轻质砂浆复合聚氨酯板外墙外保温系统能有效解决该问题。详细介绍了系统构造、组成材料的性能、工艺流程及施工要点,并对系统技术优势进行了分析,通过工程验证表明:轻质砂浆复合聚氨酯板外墙外保温系统是一项值得推广应用的外墙外保温技术。%Rigid polyurethane composite foam board is a new external thermal board. After application of the thin plastering external thermal insulation with rigid polyurethane foam board, some buildings appear the quality problems of visible board frames and cracking gaps of rigid polyurethane foam board. The external thermal insulation system based on lightweight mortar composite with rigid polyurethane foam board can successfully solve these problems. Technical structure, the performance of the composite materials, construction process and key points are introduced in detail,and the technical advantages in the system are analyzed. The engineering application result shows that external thermal insulation system based on lightweight mortar composite with rigid polyurethane foam board is worth popularizing and applying.

  8. Lightweight bipolar storage battery

    Science.gov (United States)

    Rowlette, John J. (Inventor)

    1992-01-01

    An apparatus [10] is disclosed for a lightweight bipolar battery of the end-plate cell stack design. Current flow through a bipolar cell stack [12] is collected by a pair of copper end-plates [16a,16b] and transferred edgewise out of the battery by a pair of lightweight, low resistance copper terminals [28a,28b]. The copper terminals parallel the surface of a corresponding copper end-plate [16a,16b] to maximize battery throughput. The bipolar cell stack [12], copper end-plates [16a,16b] and copper terminals [28a,28b] are rigidly sandwiched between a pair of nonconductive rigid end-plates [20] having a lightweight fiber honeycomb core which eliminates distortion of individual plates within the bipolar cell stack due to internal pressures. Insulating foam [30] is injected into the fiber honeycomb core to reduce heat transfer into and out of the bipolar cell stack and to maintain uniform cell performance. A sealed battery enclosure [ 22] exposes a pair of terminal ends [26a,26b] for connection with an external circuit.

  9. Lightweight Trauma Module - LTM

    Science.gov (United States)

    Hatfield, Thomas

    2008-01-01

    Current patient movement items (PMI) supporting the military's Critical Care Air Transport Team (CCATT) mission as well as the Crew Health Care System for space (CHeCS) have significant limitations: size, weight, battery duration, and dated clinical technology. The LTM is a small, 20 lb., system integrating diagnostic and therapeutic clinical capabilities along with onboard data management, communication services and automated care algorithms to meet new Aeromedical Evacuation requirements. The Lightweight Trauma Module is an Impact Instrumentation, Inc. project with strong Industry, DoD, NASA, and Academia partnerships aimed at developing the next generation of smart and rugged critical care tools for hazardous environments ranging from the battlefield to space exploration. The LTM is a combination ventilator/critical care monitor/therapeutic system with integrated automatic control systems. Additional capabilities are provided with small external modules.

  10. On the automobile lightweight

    Institute of Scientific and Technical Information of China (English)

    Ma Mingtu; Yi Hongliang; Lu Hongzhou; Wan Xinming

    2012-01-01

    The significance, description parameters, evaluation method, implement way and design for lightweight of au- tomobile are comprehensively reviewed. The relationship among the performances of auto parts & components, the prop- erties of materials and application of advanced technologies is also elaborated. According to recently related progress of lightweight and authors' research and developing work, lightweight of automobile is comprehensively and systematically overviewed.

  11. A theoretical analysis of the electromagnetic environment of the AS330 super Puma helicopter external and internal coupling

    Science.gov (United States)

    Flourens, F.; Morel, T.; Gauthier, D.; Serafin, D.

    1991-01-01

    Numerical techniques such as Finite Difference Time Domain (FDTD) computer programs, which were first developed to analyze the external electromagnetic environment of an aircraft during a wave illumination, a lightning event, or any kind of current injection, are now very powerful investigative tools. The program called GORFF-VE, was extended to compute the inner electromagnetic fields that are generated by the penetration of the outer fields through large apertures made in the all metallic body. Then, the internal fields can drive the electrical response of a cable network. The coupling between the inside and the outside of the helicopter is implemented using Huygen's principle. Moreover, the spectacular increase of computer resources, as calculations speed and memory capacity, allows the modellization structures as complex as these of helicopters with accuracy. This numerical model was exploited, first, to analyze the electromagnetic environment of an in-flight helicopter for several injection configurations, and second, to design a coaxial return path to simulate the lightning aircraft interaction with a strong current injection. The E field and current mappings are the result of these calculations.

  12. Research on Application of Lightweight Mortar Used as Internal and External Thermal Insulation System%轻质砂浆内外组合保温系统技术应用研究

    Institute of Scientific and Technical Information of China (English)

    杨红玉; 钱忠勤

    2012-01-01

    In this paper the defects of the traditional building energy conservation system and the new type of lightweight mortar used as internal and external thermal insulation system for the building are presented. The improvement of the thermal insulation system, key technology of the energy conservation system, civil engineering application and the economic effect analysis are mainly discussed. The application shows that this kind of thermal insulation system has many obvious advantages; material property improvement, technical innovation and making full use of material properties. The new building material and the construction technology are energy saving, environmental protection and have very good application and promotion value in civil engineering field.%在分析当前建筑节能保温系统存在缺陷的基础上,提供了一种新型的轻质砂浆内外组合保温系统.文章着重介绍了该系统保温材料的改性研究理念;轻质砂浆内外组合保温系统实施以及工程应用实例及其效益分析.实践表明,该轻质砂浆内外组合保温系统摒弃了以往保温做法的缺陷,通过技术上的有效创新,使材料及其材料性能得以充分利用和发挥,从而达到节能、环保、持久的经济效益和社会效益,具有推广应用潜力.

  13. ULTRA-LIGHTWEIGHT CEMENT

    Energy Technology Data Exchange (ETDEWEB)

    Fred Sabins

    2002-07-30

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). This report includes results from laboratory testing of ULHS systems along with other lightweight cement systems, including foamed and sodium silicate slurries. During this project quarter, a comparison study of the three cement systems examined the effect that cement drillout has on the three cement systems. Testing to determine the effect of pressure cycling on the shear bond properties of the cement systems was also conducted. This report discusses testing that was performed to analyze the alkali-silica reactivity of ULHS in cement slurries.

  14. Lightweight Robotic Excavation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Robust, lightweight, power-efficient excavation robots are mission enablers for lunar outposts and surface systems. Lunar excavators of this type cost-effectively...

  15. Lightweight Robotic Excavation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Lightweight robotic excavators address the need for machines that dig, collect, transport and dump lunar soil. Robust and productive small robots enable mining rich...

  16. Lightweight Metal Mirrors

    Science.gov (United States)

    Gossett, E.; Winslow, P.

    1984-01-01

    Two "eggcrate" halves brazed together. Lightweight flat mirrors fabricated by machining pockets in two plates of beryllium and brazing machined halves together. Mirror less than half weight of same mirror made by previous design.

  17. Manufacturing of Lightweight Mirror

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Fabrication of the lightweight mirror is one of the key techniques for many large optical systems. CAD,CAM and CNC technologies are adopted in designing and manufacturing such mirrors in CIOMP. Better working efficiency and higher lightweight grade have been achieved. The results show that mirrors up to 70% weight reduction and 0.02λ(rms.) surface accuracy or better can be obtained.

  18. ULTRA-LIGHTWEIGHT CEMENT

    Energy Technology Data Exchange (ETDEWEB)

    Fred Sabins

    2001-10-23

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). Work reported herein addresses tasks performed in the fourth quarter as well as the other three quarters of the past year. The subjects that were covered in previous reports and that are also discussed in this report include: Analysis of field laboratory data of active cement applications from three oil-well service companies; Preliminary findings from a literature review focusing on problems associated with ultra-lightweight cements; Summary of pertinent information from Russian ultra-lightweight cement literature review; and Comparison of compressive strengths of ULHS systems using ultrasonic and crush methods Results reported from the fourth quarter include laboratory testing of ULHS systems along with other lightweight cement systems--foamed and sodium silicate slurries. These comparison studies were completed for two different densities (10.0 and 11.5 lb/gal) and three different field application scenarios. Additional testing included the mechanical properties of ULHS systems and other lightweight systems. Studies were also performed to examine the effect that circulation by centrifugal pump during mixing has on breakage of ULHS.

  19. ULTRA-LIGHTWEIGHT CEMENT

    Energy Technology Data Exchange (ETDEWEB)

    Fred Sabins

    2001-04-15

    The objective of this project is to develop an improved ultra-lightweight cement using ultralight hollow glass spheres (ULHS). Work reported herein addresses Task 1: Assess Ultra-Lightweight Cementing Problems and Task 3: Test Ultra-Lightweight Cements. Results reported this quarter include a review and summary of Halliburton Energy Services (HES) and BJ Services historical performance data for lightweight cement applications. These data are analyzed and compared to ULHS cement and foamed cement performances. Similar data is expected from Schlumberger, and an analysis of this data will be completed in the following phases of the project. Quality control testing of materials used to formulate ULHS cements in the laboratory was completed to establish baseline material performance standards. A testing protocol was developed employing standard procedures as well as procedures tailored to evaluate ULHS and foamed cement. This protocol is presented and discussed. Results of further testing of ULHS cements are presented along with an analysis to establish cement performance design criteria to be used during the remainder of the project. Finally, a list of relevant literature on lightweight cement performance is compiled for review during the next quarter.

  20. ULTRA-LIGHTWEIGHT CEMENT

    Energy Technology Data Exchange (ETDEWEB)

    Fred Sabins

    2002-01-23

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). This report includes results from laboratory testing of ULHS systems along with other lightweight cement systems: foamed and sodium silicate slurries. Comparison studies of the three cement systems examined several properties: tensile strength, Young's modulus, water permeability, and shear bond. Testing was also done to determine the effect that temperature cycling has on the shear bond properties of the cement systems. In addition, analysis was carried out to examine alkali silica reactivity of slurries containing ULHS. Data is also presented from a study investigating the effects of mixing and pump circulation on breakage of ULHS. Information is also presented about the field application of ULHS in cementing a 7-in. intermediate casing in south Texas.

  1. Lightweight Composite Intertank Structure

    Science.gov (United States)

    Mehle, Greg V.

    1995-01-01

    Report presents results of study for proposed lightweight composite material alternative to present semimonocoque aluminum intertank structure for advanced launch vehicles. Proposed structure integrated assembly of sandwich panels made of laminated epoxy-matrix/carbon-fiber skins, and aluminum honeycomb core.

  2. Lightweight Electric Power Cable.

    Science.gov (United States)

    1982-09-01

    8I~ .4 111 162 MICROCi Pi RL’ LUHION TESI CHARI "LIGHTWEIGHT ELECTRIC POWER CABLE" FINAL TECHNICAL REPORT SEPTEMBER 30, 1981 to SEPTEMBER 30, 1982... Vulcanized by heat to crosslink. TPE (Thermoplastic Elastomer) - Polymers having elastomeric proper- ties. Used as thermoplastics - melt formed by

  3. Lightweight incremental application upgrade

    NARCIS (Netherlands)

    T. van der Storm (Tijs)

    2006-01-01

    textabstractI present a lightweight approach to incremental application upgrade in the context of component-based software development. The approach can be used to efficiently implement an automated update feature in a platform and programming language agnostic way. A formal release model is present

  4. Thin, Lightweight Solar Cell

    Science.gov (United States)

    Brandhorst, Henry W., Jr.; Weinberg, Irving

    1991-01-01

    Improved design for thin, lightweight solar photovoltaic cells with front contacts reduces degradation of electrical output under exposure to energetic charged particles (protons and electrons). Increases ability of cells to maintain structural integrity under exposure to ultraviolet radiation by eliminating ultraviolet-degradable adhesives used to retain cover glasses. Interdigitated front contacts and front junctions formed on semiconductor substrate. Mating contacts formed on back surface of cover glass. Cover glass and substrate electrostatically bonded together.

  5. The controllable super-high energetic electrons by external magnetic fields at relativistic laser-solid interactions in the presence of large scale pre-plasmas

    CERN Document Server

    Wu, D; Luan, S X; Yu, W

    2016-01-01

    The two stage electron acceleration model [arXiv: 1512.02411 and arXiv: 1512.07546] is extended to the study of laser magnetized-plasmas interactions at relativistic intensities and in the presence of large-scale preformed plasmas. It is shown that the cut-off electron kinetic energy is controllable by the external magnetic field strength and directions. Further studies indicate that for a right-hand circularly polarized laser (RH-CP) of intensity $10^{20}\\ \\text{W}/\\text{cm}^2$ and pre-plasma scale length $10\\ \\mu\\text{m}$, the cut-off electron kinetic energy can be as high as $500\\ \\text{MeV}$, when a homogeneous external magnetic field of exceeding $10000\\ \\text{T}$ (or $B=\\omega_{c}/\\omega_0>1$) is loaded along the laser propagation direction, which is a significant increase compared with that $120\\ \\text{MeV}$ without external magnetic field. A laser front sharpening mechanism is identified at relativistic laser magnetized-plasmas interactions with $B=\\omega_{c}/\\omega_0>1$, which is responsible for thes...

  6. Super Special Codes using Super Matrices

    CERN Document Server

    Kandasamy, W B Vasantha; Ilanthenral, K

    2010-01-01

    The new classes of super special codes are constructed in this book using the specially constructed super special vector spaces. These codes mainly use the super matrices. These codes can be realized as a special type of concatenated codes. This book has four chapters. In chapter one basic properties of codes and super matrices are given. A new type of super special vector space is constructed in chapter two of this book. Three new classes of super special codes namely, super special row code, super special column code and super special codes are introduced in chapter three. Applications of these codes are given in the final chapter.

  7. Lightweight enterprise architectures

    CERN Document Server

    Theuerkorn, Fenix

    2004-01-01

    STATE OF ARCHITECTUREArchitectural ChaosRelation of Technology and Architecture The Many Faces of Architecture The Scope of Enterprise Architecture The Need for Enterprise ArchitectureThe History of Architecture The Current Environment Standardization Barriers The Need for Lightweight Architecture in the EnterpriseThe Cost of TechnologyThe Benefits of Enterprise Architecture The Domains of Architecture The Gap between Business and ITWhere Does LEA Fit? LEA's FrameworkFrameworks, Methodologies, and Approaches The Framework of LEATypes of Methodologies Types of ApproachesActual System Environmen

  8. LIGHTWEIGHT CONCRETE BASED GRANSHLAK

    Directory of Open Access Journals (Sweden)

    NETESA M. I.

    2016-02-01

    Full Text Available Raising of problem. Concrete advisable to obtain a low strength with local secondary resources for recycling and reduce the environmental burden on the environment. But it is important to design such concrete compositions with a reduced flow of cement. It is known that the coefficient of efficiency of use of cement in the concrete of the heavy and B10 is less than about 0.5, which is almost two times smaller than in class B15 concrete and above. Even lower coefficient of efficiency in light concrete cement low strength. Therefore, it is important to find patterns determining the composition of lightweight concrete based on local-products industry with more efficient use of cement in them. Purpose.. Based on the analysis of earlier research results, including with the use of methods of mathematical planning of experiments to determine the concrete contents, which can provide the requirements for the underlying layers of the floor, the compressive strength of which should correspond to the class B5. It is important to provide the required strength at minimum flow of the cement, which is the most expensive and energy-intensive part of concrete. Conclusion. Analysis of the test results of control samples of concrete in 28-day-old, the following laws. The required tensile strength of concrete compressive strength of 7.0 MPa can be obtained in the test range when used in formulations as a filler as the Dnieper hydroelectric power station fly ash and tailings Krivoy Rog iron ore YuGOK. To ensure providing the required characteristic strength of the concrete in the underlying layers of the floor is advisable to use a nominal composition per cubic meter of concrete: cement 160 kg granshlaka Plant named after Petrovsky, 675 kg of fly ash Dnieper HPP 390 kg, 400 kg of sand, 230 liters of water. Thus, while ensuring rational grain composition components can obtain the desired strength lightweight concrete based granshlaka plant Petrovsky, using as fillers

  9. Super Lightweight, Metal Rubber Fabric for Extreme Space Environments Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NanoSonic has fabricated revolutionary nanostructured, yet macroscale, multifunctional Metal RubberTM films via layer-by-layer, molecular self-assembly, which...

  10. Super Factories

    Indian Academy of Sciences (India)

    D G Hitlin

    2006-11-01

    Heavy-flavor physics, in particular and physics results from the factories, currently provides strong constraints on models of physics beyond the Standard Model. A new generation of colliders, Super Factories, with 50 to 100 times the luminosity of existing colliders, can, in a dialog with LHC and ILC, provide unique clarification of new physics phenomena seen at those machines.

  11. Lightweight flywheel containment

    Science.gov (United States)

    Smith, James R.

    2004-06-29

    A lightweight flywheel containment composed of a combination of layers of various material which absorb the energy of a flywheel structural failure. The various layers of material act as a vacuum barrier, momentum spreader, energy absorber, and reaction plate. The flywheel containment structure has been experimentally demonstrated to contain carbon fiber fragments with a velocity of 1,000 m/s and has an aerial density of less than 6.5 g/square centimeters. The flywheel containment, may for example, be composed of an inner high toughness structural layer, and energy absorbing layer, and an outer support layer. Optionally, a layer of impedance matching material may be utilized intermediate the flywheel rotor and the inner high toughness layer.

  12. Computational imaging using lightweight diffractive-refractive optics

    KAUST Repository

    Peng, Yifan

    2015-11-23

    Diffractive optical elements (DOE) show great promise for imaging optics that are thinner and more lightweight than conventional refractive lenses while preserving their light efficiency. Unfortunately, severe spectral dispersion currently limits the use of DOEs in consumer-level lens design. In this article, we jointly design lightweight diffractive-refractive optics and post-processing algorithms to enable imaging under white light illumination. Using the Fresnel lens as a general platform, we show three phase-plate designs, including a super-thin stacked plate design, a diffractive-refractive-hybrid lens, and a phase coded-aperture lens. Combined with cross-channel deconvolution algorithm, both spherical and chromatic aberrations are corrected. Experimental results indicate that using our computational imaging approach, diffractive-refractive optics is an alternative candidate to build light efficient and thin optics for white light imaging.

  13. Computational imaging using lightweight diffractive-refractive optics.

    Science.gov (United States)

    Peng, Yifan; Fu, Qiang; Amata, Hadi; Su, Shuochen; Heide, Felix; Heidrich, Wolfgang

    2015-11-30

    Diffractive optical elements (DOE) show great promise for imaging optics that are thinner and more lightweight than conventional refractive lenses while preserving their light efficiency. Unfortunately, severe spectral dispersion currently limits the use of DOEs in consumer-level lens design. In this article, we jointly design lightweight diffractive-refractive optics and post-processing algorithms to enable imaging under white light illumination. Using the Fresnel lens as a general platform, we show three phase-plate designs, including a super-thin stacked plate design, a diffractive-refractive-hybrid lens, and a phase coded-aperture lens. Combined with cross-channel deconvolution algorithm, both spherical and chromatic aberrations are corrected. Experimental results indicate that using our computational imaging approach, diffractive-refractive optics is an alternative candidate to build light efficient and thin optics for white light imaging.

  14. Lightweight Inflatable Cryogenic Tank Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal describes the development of an inflatable and lightweight polymer-fabric structured pressure vessel designed for the containment of cryogenic fluids....

  15. High Efficency Lightweight Radiators Project

    Data.gov (United States)

    National Aeronautics and Space Administration — XC Associates proposes to build on prior work to develop and characterize a very high efficiency, lightweight radiator constructed from high thermal conductivity...

  16. The Super Patalan Numbers

    OpenAIRE

    Richardson, Thomas M.

    2014-01-01

    We introduce the super Patalan numbers, a generalization of the super Catalan numbers in the sense of Gessel, and prove a number of properties analagous to those of the super Catalan numbers. The super Patalan numbers generalize the super Catalan numbers similarly to how the Patalan numbers generalize the Catalan numbers.

  17. dbSUPER: a database of super-enhancers in mouse and human genome.

    Science.gov (United States)

    Khan, Aziz; Zhang, Xuegong

    2016-01-04

    Super-enhancers are clusters of transcriptional enhancers that drive cell-type-specific gene expression and are crucial to cell identity. Many disease-associated sequence variations are enriched in super-enhancer regions of disease-relevant cell types. Thus, super-enhancers can be used as potential biomarkers for disease diagnosis and therapeutics. Current studies have identified super-enhancers in more than 100 cell types and demonstrated their functional importance. However, a centralized resource to integrate all these findings is not currently available. We developed dbSUPER (http://bioinfo.au.tsinghua.edu.cn/dbsuper/), the first integrated and interactive database of super-enhancers, with the primary goal of providing a resource for assistance in further studies related to transcriptional control of cell identity and disease. dbSUPER provides a responsive and user-friendly web interface to facilitate efficient and comprehensive search and browsing. The data can be easily sent to Galaxy instances, GREAT and Cistrome web-servers for downstream analysis, and can also be visualized in the UCSC genome browser where custom tracks can be added automatically. The data can be downloaded and exported in variety of formats. Furthermore, dbSUPER lists genes associated with super-enhancers and also links to external databases such as GeneCards, UniProt and Entrez. dbSUPER also provides an overlap analysis tool to annotate user-defined regions. We believe dbSUPER is a valuable resource for the biology and genetic research communities.

  18. Lightweight hydride storage materials

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, G.J.; Guthrie, S.E.; Bauer, W. [Sandia National Labs., Livermore, CA (United States)

    1995-09-01

    The need for lightweight hydrides in vehicular applications has prompted considerable research into the use of magnesium and its alloys. Although this earlier work has provided some improved performance in operating temperature and pressure, substantial improvements are needed before these materials will significantly enhance the performance of an engineered system on a vehicle. We are extending the work of previous investigators on Mg alloys to reduce the operating temperature and hydride heat of formation in light weight materials. Two important results will be discussed in this paper: (1) a promising new alloy hydride was found which has better pressure-temperature characteristics than any previous Mg alloy and, (2) a new fabrication process for existing Mg alloys was developed and demonstrated. The new alloy hydride is composed of magnesium, aluminum and nickel. It has an equilibrium hydrogen overpressure of 1.3 atm. at 200{degrees}C and a storage capacity between 3 and 4 wt.% hydrogen. A hydrogen release rate of approximately 5 x 10{sup -4} moles-H{sub 2}/gm-min was measured at 200{degrees}C. The hydride heat of formation was found to be 13.5 - 14 kcal/mole-H{sub 2}, somewhat lower than Mg{sub 2}Ni. The new fabrication method takes advantage of the high vapor transport of magnesium. It was found that Mg{sub 2}Ni produced by our low temperature process was better than conventional materials because it was single phase (no Mg phase) and could be fabricated with very small particle sizes. Hydride measurements on this material showed faster kinetic response than conventional material. The technique could potentially be applied to in-situ hydride bed fabrication with improved packing density, release kinetics, thermal properties and mechanical stability.

  19. FEM Simulation of Bending Formability for Laminate Steel/Resin/Steel Lightweight Composite Sheet

    Institute of Scientific and Technical Information of China (English)

    Guancheng Ll; Yonglin KANG

    2003-01-01

    The ANSYS simulation software was used to analyze the bending formability of laminate steel/resin/steel lightweight composite sheet. The skin steel at external side produces relative slipping-off change during the bending due to its composite structure. The internal stress strain states, materials effect tools parameters and intermediate layer resin of lightweight sheet on slipping-off change were analyzed. The spring back and shear stress state after bending have also been discussed.

  20. Lightweight cryptography for constrained devices

    DEFF Research Database (Denmark)

    Alippi, Cesare; Bogdanov, Andrey; Regazzoni, Francesco

    2014-01-01

    Lightweight cryptography is a rapidly evolving research field that responds to the request for security in resource constrained devices. This need arises from crucial pervasive IT applications, such as those based on RFID tags where cost and energy constraints drastically limit the solution...

  1. Lightweight, Wearable, Metal Rubber Sensor

    Science.gov (United States)

    Hill, Andrea

    2015-01-01

    For autonomous health monitoring. NanoSonic, Inc., has developed comfortable garments with multiple integrated sensors designed to monitor astronaut health throughout long-duration space missions. The combined high electrical conductivity, low mechanical modulus, and environmental robustness of the sensors make them an effective, lightweight, and comfortable alternative to conventional use of metal wiring and cabling.

  2. Airborne and impact sound transmission in super-light structures

    DEFF Research Database (Denmark)

    Christensen, Jacob Ellehauge; Hertz, Kristian Dahl; Brunskog, Jonas

    2011-01-01

    Super-light structures are newly invented and based on combining lightweight concrete with normal concrete for lighter structures and better structural performance. The overall principle is based on load carrying arches of a normal concrete stabilised and protected from fire by a light......-aggregate concrete. A super-light deck element is developed. It is intended to be lighter than traditional deck structures without compromising the acoustic performance. It is primarily the airborne sound insulation, which is of interest as the requirements for the impact sound insulation to a higher degree can...

  3. Fundamental Study on the Development of Structural Lightweight Concrete by Using Normal Coarse Aggregate and Foaming Agent

    Directory of Open Access Journals (Sweden)

    Han-Seung Lee

    2014-06-01

    Full Text Available Structural lightweight concrete (SLWC has superior properties that allow the optimization of super tall structure systems for the process of design. Because of the limited supply of lightweight aggregates in Korea, the development of structural lightweight concrete without lightweight aggregates is needed. The physical and mechanical properties of specimens that were cast using normal coarse aggregates and different mixing ratios of foaming agent to evaluate the possibility of creating structural lightweight concrete were investigated. The results show that the density of SLWC decreases as the dosage of foaming agent increases up to a dosage of 0.6%, as observed by SEM. It was also observed that the foaming agent induced well separated pores, and that the size of the pores ranged from 50 to 100 μm. Based on the porosity of concrete specimens with foaming agent, compressive strength values of structural lightweight foam concrete (SLWFC were obtained. It was also found that the estimated values from proposed equations for compressive strength and modulus of elasticity of SLWFC, and values obtained by actual measurements were in good agreement. Thus, this study confirms that new structural lightweight concrete using normal coarse aggregates and foaming agent can be developed successfully.

  4. Lightweight Space Tug body structure

    Science.gov (United States)

    Lager, J. R.

    1976-01-01

    Lightweight honeycomb sandwich construction using a wide variety of metal and fibrous composite faceskins was used in the design of a typical Space Tug skirt structure. Relatively low magnitude combined loading of axial compression and torsion resulted in designs using ultrathin faceskins, lightweight honeycomb cores, and thin faceskin/core adhesive bond layers. Two of the designs with metal faceskins (aluminum and titanium) and four with fibrous composite faceskins (using combinations of fiberglass, boron, and graphite) were evaluated through the fabrication and structural test of a series of small development panels. The two most promising concepts with aluminum and graphite/epoxy faceskins, were further evaluated through the fabrication and structural test of larger compression and shear panels. All panels tested exceeded design ultimate load levels, thereby, verifying the structural integrity of the selected designs. Projected skirt structural weights for the graphite/epoxy and aluminum concepts fall within original weight guidelines established for the Space Tug vehicle.

  5. Making Lightweight Structures By Vapor Deposition

    Science.gov (United States)

    Goela, Jitendra S.; Pickering, Michael A.; Taylor, Raymond L.

    1990-01-01

    Technique developed for fabrication of stiff, strong, lightweight structures of silicon carbide or other materials by any of several deposition processes. Structures made by method can have complicated shapes. Ability to manufacture complex shape from pure deposited SiC useful and leads to new products in several fields. These lightweight structures used as backup structures for optical components, as structural components in automotive, aerospace, and outer space applications, and as lightweight parts of furniture for outer space.

  6. Lightweight and Energy Efficient Heat Pump Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Future Spacecraft from the JPL will require increasingly sophisticated thermal control technology. A need exists for efficient, lightweight Vapor Compression Cycle...

  7. Modular Self-Rigidizing Lightweight Structures Project

    Data.gov (United States)

    National Aeronautics and Space Administration — An innovative structures concept has been developed that uses space qualified flexible thin film polyimide to produce ultra-lightweight inflation deployed...

  8. Spongent: A lightweight hash function

    DEFF Research Database (Denmark)

    Bogdanov, Andrey; Knežević, Miroslav; Leander, Gregor

    2011-01-01

    This paper proposes spongent - a family of lightweight hash functions with hash sizes of 88 (for preimage resistance only), 128, 160, 224, and 256 bits based on a sponge construction instantiated with a present-type permutation, following the hermetic sponge strategy. Its smallest implementations...... of serialization degree and speed. We explore some of its numerous implementation trade-offs. We furthermore present a security analysis of spongent. Basing the design on a present-type primitive provides confidence in its security with respect to the most important attacks. Several dedicated attack approaches...

  9. Manufacturing Precise, Lightweight Paraboloidal Mirrors

    Science.gov (United States)

    Hermann, Frederick Thomas

    2006-01-01

    A process for fabricating a precise, diffraction- limited, ultra-lightweight, composite- material (matrix/fiber) paraboloidal telescope mirror has been devised. Unlike the traditional process of fabrication of heavier glass-based mirrors, this process involves a minimum of manual steps and subjective judgment. Instead, this process involves objectively controllable, repeatable steps; hence, this process is better suited for mass production. Other processes that have been investigated for fabrication of precise composite-material lightweight mirrors have resulted in print-through of fiber patterns onto reflecting surfaces, and have not provided adequate structural support for maintenance of stable, diffraction-limited surface figures. In contrast, this process does not result in print-through of the fiber pattern onto the reflecting surface and does provide a lightweight, rigid structure capable of maintaining a diffraction-limited surface figure in the face of changing temperature, humidity, and air pressure. The process consists mainly of the following steps: 1. A precise glass mandrel is fabricated by conventional optical grinding and polishing. 2. The mandrel is coated with a release agent and covered with layers of a carbon- fiber composite material. 3. The outer surface of the outer layer of the carbon-fiber composite material is coated with a surfactant chosen to provide for the proper flow of an epoxy resin to be applied subsequently. 4. The mandrel as thus covered is mounted on a temperature-controlled spin table. 5. The table is heated to a suitable temperature and spun at a suitable speed as the epoxy resin is poured onto the coated carbon-fiber composite material. 6. The surface figure of the optic is monitored and adjusted by use of traditional Ronchi, Focault, and interferometric optical measurement techniques while the speed of rotation and the temperature are adjusted to obtain the desired figure. The proper selection of surfactant, speed or rotation

  10. Moisture and Thermal Conductivity of Lightweight Block Walls

    Science.gov (United States)

    Joosep, R.

    2015-11-01

    This article examines thermal properties of lightweight block walls and their changes over the course of time. Three different types of lightweight blocks and two types of heat insulation are used in construction. Aeroc aerated concrete blocks are in use, as well as compacted LECA (Lightweight Expanded Clay Aggregate) Fibo blocks made from burned clay and Silbet blocks produced from oil shale ash. Expanded Thermisol EPS60F polystyrene plates and glass wool Isover OL-P plates are used for thermal insulation. The actual and computational values of thermal conductivity and the water draining properties of walls over time are compared in this article. Water draining from glass wool walls is relatively fast. Water-draining can take over a year in polystyrene insulated walls. All four wall constructions can be used as external walls, but care must be taken regarding the moisture content of the blocks during construction (the construction should be handled with care to minimise the moisture in the blocks), especially in polystyrene board-insulated walls.

  11. Small and lightweight power amplifiers

    Science.gov (United States)

    Shams, Qamar A.; Barnes, Kevin N.; Fox, Robert L.; Moses, Robert W.; Bryant, Robert G.; Robinson, Paul C.; Shirvani, Mir

    2002-07-01

    The control of u wanted structural vibration is implicit in most of NASA's programs. Currently several approaches to control vibrations in large, lightweight, deployable structures and twin tail aircraft at high angles of attack are being evaluated. The Air Force has been examining a vertical tail buffet load alleviation system that can be integrated onboard an F/A-18 and flown. Previous wind tunnel and full-scale ground tests using distributed actuators have shown that the concept works; however, there is insufficient rom available onboard an F/A-18 to store current state-of- the-art system components such as amplifiers, DC-to-DC converter and a computer for performing vibration suppression. Sensor processing, power electronics, DC-to-DC converters, and control electronics that may be collocated with distributed actuators, are particularly desirable. Such electronic system would obviate the need for complex, centralized, control processing and power distribution components that will eliminate the weight associated with lengthy wiring and cabling networks. Several small and lightweight power amplifiers ranging from 300V pp to 650V pp have been designed using off the shelf components for different applications. In this paper, the design and testing of these amplifiers will be presented under various electrical loads.

  12. RFID security a lightweight paradigm

    CERN Document Server

    Khattab, Ahmed; Amini, Esmaeil; Bayoumi, Magdy

    2017-01-01

    This book provides a comprehensive treatment of security in the widely adopted, Radio Frequency Identification (RFID) technology. The authors present the fundamental principles of RFID cryptography in a manner accessible to a broad range of readers, enabling them to improve their RFID security design. This book also offers the reader a range of interesting topics portraying the current state-of-the-art in RFID technology and how it can be integrated with today’s Internet of Things (IoT) vision. The authors describe a first-of-its-kind, lightweight symmetric authenticated encryption cipher called Redundant Bit Security (RBS), which enables significant, multi-faceted performance improvements compared to existing cryptosystems. This book is a must-read for anyone aiming to overcome the constraints of practical implementation in RFID security technologies.

  13. Calculus super review

    CERN Document Server

    2012-01-01

    Get all you need to know with Super Reviews! Each Super Review is packed with in-depth, student-friendly topic reviews that fully explain everything about the subject. The Calculus I Super Review includes a review of functions, limits, basic derivatives, the definite integral, combinations, and permutations. Take the Super Review quizzes to see how much you've learned - and where you need more study. Makes an excellent study aid and textbook companion. Great for self-study!DETAILS- From cover to cover, each in-depth topic review is easy-to-follow and easy-to-grasp - Perfect when preparing for

  14. Algebra & trigonometry super review

    CERN Document Server

    2012-01-01

    Get all you need to know with Super Reviews! Each Super Review is packed with in-depth, student-friendly topic reviews that fully explain everything about the subject. The Algebra and Trigonometry Super Review includes sets and set operations, number systems and fundamental algebraic laws and operations, exponents and radicals, polynomials and rational expressions, equations, linear equations and systems of linear equations, inequalities, relations and functions, quadratic equations, equations of higher order, ratios, proportions, and variations. Take the Super Review quizzes to see how much y

  15. 有限内固定结合铰链式超关节外固定架治疗肱骨远端复杂骨折%Limited internal fixation combined with super-articular external fixator for complex distal humeral fractures

    Institute of Scientific and Technical Information of China (English)

    郭亚洲; 徐辉; 郑均华; 万昌涛; 钱苏林; 曾舸

    2012-01-01

    Objective To evaluate the application of limited internal fixation combined with hinged super - articular external fixator for complex distal humeral fractures( CDHF ). Methods Twelve cases of CDHF were treated with limited internal fixation combined with hinged super - articular externnal fixator, and the results were analyzed. Results All 12 patients were followed up for a mean duration of 7 months( range 4 ~ 15 months ). According to the Morrey scoring system,results were excellent in 7 cases, good in 3 , fair in 2, and the effective rate was 83. 3% . All cases of fracture healed without severe complication such as infection,limited flection or extension of elbow joint,cubitus varus and nerve injury. Conclusion Limited internal fixation combined with hinged super - articular external fixator in treatment of complex distal humeral fractures can promote early rehabilitation and improve the recovery of elbow function, which is an effective treatment for CDHF.%目的 总结有限内固定结合铰链式超关节外固定架治疗肱骨远端复杂骨折的效果.方法 对12例肱骨远端复杂骨折采用有限内固定结合铰链式超关节外固定架固定进行治疗.结果 12 例全部获得随访,随访时间平均7个月(4~15个月),根据Morrey指定评估指数评价,优7例,良3例,可2例.优良率83.3%.无感染、关节僵硬、肘内翻畸形、神经损伤等严重并发症发生.结论 有限内固定结合铰链式超关节外固定架治疗能早期进行关节活动,可明显恢复关节功能,是一种良好的治疗肱骨远端复杂骨折的方法.

  16. Super Tomboy Style

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Sparked by Super Girl, the androgynous look is in among Chinese youth On September 8, this year's top six contestants on the Super Girl television show, a singing contest for young women, stepped into the spotlight. Nearly none of them had long black hair or wore evening gowns, traditionally associated with beauty in China. Rather, they

  17. Structural behaviour of super-light structures

    DEFF Research Database (Denmark)

    Bagger, Anne; Hertz, Kristian Dahl

    2010-01-01

    with a lighter and softer material, such as lightweight concrete. The combined use of stiff and light material in SLS results in structures of high stiffness and low weight. The applied technology and the advantages of SLS are elaborated upon in [1] in these proceedings. The present paper focuses......A new structural concept, called Super-light Structures (SLS), has recently been invented and patented at the Technical University of Denmark. The basic concept of SLS is to construct a skeleton of a stiff and strong material, such as ordinary or high strength concrete, and stabilize this skeleton...... on the structural correlation between the stiff material and the light material. The shape of the skeleton can be optimized for the primary load on the structure, and it will take up the majority of the load. The lighter material forms the outer geometry of the structural component (e.g. a wall), and has several...

  18. EVOLUTION OF LIGHTWEIGHT WOOD COMPOSITES

    Directory of Open Access Journals (Sweden)

    Marius C. BARBU

    2016-01-01

    Full Text Available Lightweight boards and beams in the wood-based construction and furniture industry are not a new topic. The density reduction of panels using sandwich structure with light cores was confirmed by users like doors or mobile homes more than three decades ago. Today many ways to attain a lighter wooden structure are on offer, partially in industrial application. The first one is the use of light-weight wood species like balsa, lime, pine from southern hemisphere plantations etc. limited by the availability, strength properties, gluability and so on. A second one is the sandwich structure made from hard faces like thick veneer, thin plywood, particleboard or high density thin fiberboard and cores made from honeycomb paper, very light wood species or foams like the polystyrene one. A third way to produce a light structure is to reduce the core drastically, using predesigned skeletons with special shapes and connections to the faces. The engines for these developments are on the one hand the fast growing market of knockdown furniture and on the other hand the increasing costs for energy and raw materials. Additional factors that make weight saving a primary economical objective for most producers are transportation costs, easier handling and higher acceptance among the end users. Moreover, customers demand more for ergonomical solutions regarding packaging. Many patents were generated by researchers and developers for new one-stage production processes for sandwich panels with wood- and impregnated paper-based facings made from veneers, particles or fibres and a core consisting of expandable foams, particles or embedded hard skeletons. These ideas or prototypes could be integrated in existing continuous pressing lines for wood based panels keeping some of the advantages of the continuous production technique in matters of efficiency. Some of the challenges of the light weight wooden structure are the connection in half or final parts, resistance to

  19. Chemical Acidic Attack Resistance of Lightweight Concrete with Additives

    Directory of Open Access Journals (Sweden)

    Salwa H. Ahmed

    2013-04-01

    Full Text Available  This research was studied the effect of H2SO4(8% , HCl (8% acidic and wastewaterpH= 5.1, SO4= = 850mg/L, Cl-=750 mg/L , TDS = 2500 mg/L( on the lightweight concrete by using limestone as lightweight aggregate and using the foam material (LightCrete. Super plasticizers (SP also used to enhance the properties of the lightweight concrete. Studying the effect of acidic solution and wastewater was done by calculating the percentage of decrease in weight and compressive strength of concrete prisms (100 * 100 * 400 mm, where the small portion of the flexural modulus test was submerged completely in the above solutions,  and the salt rising was observed by immersion (100 mm depth from the second portion of the prism in the above solutions. اظهرت نتائج الفحوصات ان H 2 SO 4 يكون تأثيره اكثر من HCl بالنسبة للنقصان بالوزن على الخرسانة الاعتيادية  بينما يكون تأثير HCl كبير على الخرسانة خفيفة الوزن بأستخدام الركام خفيف الوزن (Limestone وتأثيره اقل من H 2 SO 4 بالنسبة للخرسانة خفيفة الوزن باستخدام المادة الرغوية . Results show that the H2SO4 have influence larger than HCl for the decrease of weight on the normal concrete while the effect of HCl was larger than H2SO4  on lightweight concrete with limestone and its effect was less than H2SO4 on the lightweight concrete with foam. وكذلك تبين ان تأثير H 2 SO 4 على الخرسانة الاعتيادية بالنسبة للنقصان بالمقاومة يكون اقل من تاثير HCl بينما يكون تاثير H 2 SO 4 كبير على الخرسانة خفيفة الوزن الحاوية على المادة الرغوية وتاثيره اقل على الخرسانة خفيفة الوزن الحاوية على SP و Limestone . The results also shown that the effect of H2SO4 on the normal

  20. Lightweight composite mirrors for telescopes Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Lightweight, steady and stiff mirrors are necessary to decrease cost of telescopes such as IXO and GenX used in special NASA missions. Low-density materials are...

  1. Vibro-acoustics of lightweight sandwich structures

    CERN Document Server

    Lu, Tianjian

    2014-01-01

    Vibro-Acoustics of Lightweight Sandwich Structures introduces the study of the coupled vibration and acoustic behavior of lightweight sandwich structures in response to harmonic force and sound pressure. This book focuses on the theoretical modeling and experimental investigation of lightweight sandwich structures in order to provide a predictive framework for vibro-acoustic characteristics of typical engineering structures. Furthermore, by developing solution tools, it concentrates on the influence of key systematic parameters leading to effective guidance for optimal structure design toward lightweight, high-stiffness and superior sound insulation capability. This book is intended for researchers, scientists, engineers and graduate students in mechanical engineering especially in structural mechanics, mechanics and acoustics. Fengxian Xin and Tianjian Lu both work at the School of Aerospace, Xi’an Jiaotong University.

  2. Lightweight Composite Materials for Heavy Duty Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Pruez, Jacky; Shoukry, Samir; Williams, Gergis; Shoukry, Mark

    2013-08-31

    The main objective of this project is to develop, analyze and validate data, methodologies and tools that support widespread applications of automotive lightweighting technologies. Two underlying principles are guiding the research efforts towards this objective: • Seamless integration between the lightweight materials selected for certain vehicle systems, cost-effective methods for their design and manufacturing, and practical means to enhance their durability while reducing their Life-Cycle-Costs (LCC). • Smooth migration of the experience and findings accumulated so far at WVU in the areas of designing with lightweight materials, innovative joining concepts and durability predictions, from applications to the area of weight savings for heavy vehicle systems and hydrogen storage tanks, to lightweighting applications of selected systems or assemblies in light–duty vehicles.

  3. Lightweight, High-Temperature Radiator Panels Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Lightweight, high-temperature radiators are needed for future, high-efficiency power conversion systems for Nuclear Electric Propulsion (NEP). Creare has developed...

  4. Novel Lightweight Magnets for Space Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — TYRC of Tallahassee, Florida will design, fabricate and test a novel magnet for space applications. This lightweight magnet will be designed to operate at higher...

  5. Aluminum-CNF Lightweight Radiator Components Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal relates to a new materials concept for an aluminum-carbon nanofiber composite, high thermal conductivity ultra lightweight material that will form the...

  6. Lightweight, High-Temperature Radiator Panels Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Lightweight, high-temperature radiators are needed for future, high-efficiency power conversion systems for Nuclear Electric Propulsion (NEP). Creare has developed...

  7. Complete control, direct observation and study of molecular super rotors

    CERN Document Server

    Korobenko, Aleksey; Milner, Valery

    2013-01-01

    Extremely fast rotating molecules carrying significantly more energy in their rotation than in any other degree of freedom are known as "super rotors". It has been speculated that super rotors may exhibit a number of unique and intriguing properties. Theoretical studies showed that ultrafast molecular rotation may change the character of molecular scattering from solid surfaces, alter molecular trajectories in external fields, make super rotors surprisingly stable against collisions, and lead to the formation of gas vortices. New ways of molecular cooling and selective chemical bond breaking by ultrafast spinning have been proposed. Owing to the fundamental laws of nature, bringing a large number of molecules to fast, directional and synchronous rotation is rather challenging. As a result, only indirect evidence of super rotors has been reported to date. Here we demonstrate the first controlled creation, direct observation and study of molecular super rotors. Using intense laser pulses tailored to produce an ...

  8. ATTENUATION AND FLANKING TRANSMISSION IN LIGHTWEIGHT STRUCTURES

    DEFF Research Database (Denmark)

    Brunskog, Jonas; Lhomond, Alice; Ohlrich, Mogens

    2007-01-01

    In this paper the attenuation and flanking transmissions of impact noise in lightweight building structures is studied using a modal approach. The structural field is mainly analysed, putting the main attention to the parts being important in the modelling. The amount of attenuation produced...... by the periodically reinforcing beams used in lightweight building structures is analysed. The consequence of these factors in modelling flanking transmission is also discussed....

  9. Nonlinear Super Integrable Couplings of Super Classical-Boussinesq Hierarchy

    Directory of Open Access Journals (Sweden)

    Xiuzhi Xing

    2014-01-01

    Full Text Available Nonlinear integrable couplings of super classical-Boussinesq hierarchy based upon an enlarged matrix Lie super algebra were constructed. Then, its super Hamiltonian structures were established by using super trace identity. As its reduction, nonlinear integrable couplings of the classical integrable hierarchy were obtained.

  10. Super-resolution

    DEFF Research Database (Denmark)

    Nasrollahi, Kamal; Moeslund, Thomas B.

    2014-01-01

    Super-resolution, the process of obtaining one or more high-resolution images from one or more low-resolution observations, has been a very attractive research topic over the last two decades. It has found practical applications in many real world problems in different fields, from satellite...... the contributions of different authors to the basic concepts of each group. Furthermore, common issues in super-resolution algorithms, such as imaging models and registration algorithms, optimization of the cost functions employed, dealing with color information, improvement factors, assessment of super...

  11. Lightweight C/SiC mirrors for space application

    Science.gov (United States)

    Zhou, Hao; Zhang, Chang-rui; Cao, Ying-bin; Zhou, Xin-gui

    2006-02-01

    chemical vapor deposited silicon carbide (CVD SiC) cladding, is used to fabricate a 225-mm×165-mm ellipse mirror 18-mm thick and 0.41 kg weight. The mirror's backing structure contains hexagon "pockets". The individual ribs are only 2-mm thick, each contains a large cutout for structural efficiency and improves the mirror's thermal properties. Open back honeycomb lightweight structure is produced to gain 14kg/m2 area density. CVD SiC has an excellent adherence to C/SiC. It also has an excellent thermal strain match. Approximately 150-μm of this material is used to clad the mirror substrate. The CVD SiC cladding is polished to be a super smooth surface with less than 0.372-nm RMS surface roughness. Experimental results indicate that reactive melt infiltrated C/SiC can be used as optical mirror substrates. Currently, experiments are under way to fabricate a large-scale lightweight C/SiC optical mirror in diameter larger than 600-mm.

  12. NETL Super Computer

    Data.gov (United States)

    Federal Laboratory Consortium — The NETL Super Computer was designed for performing engineering calculations that apply to fossil energy research. It is one of the world’s larger supercomputers,...

  13. Super-resolution

    DEFF Research Database (Denmark)

    Nasrollahi, Kamal; Moeslund, Thomas B.

    2014-01-01

    and aerial imaging to medical image processing, to facial image analysis, text image analysis, sign and number plates reading, and biometrics recognition, to name a few. This has resulted in many research papers, each developing a new super-resolution algorithm for a specific purpose. The current......Super-resolution, the process of obtaining one or more high-resolution images from one or more low-resolution observations, has been a very attractive research topic over the last two decades. It has found practical applications in many real world problems in different fields, from satellite...... the contributions of different authors to the basic concepts of each group. Furthermore, common issues in super-resolution algorithms, such as imaging models and registration algorithms, optimization of the cost functions employed, dealing with color information, improvement factors, assessment of super...

  14. Super-Kamiokande

    Science.gov (United States)

    Magro, Lluís Martí

    2016-06-01

    The Super-Kamiokande experiment performs a large variety of studies, many of them in the neutrino sector. The archetypes are atmospheric neutrino (recently awarded with the Nobel prize for Mr. T. Kajita) and the solar neutrinos analyses. In these proceedings we report our latest results and present updates to indirect dark matter searches, our solar neutrino analysis and discuss the future upgrade of Super-Kamiokande by loading gadolinium into our ultra-pure water.

  15. The Super Girl Effect

    Institute of Scientific and Technical Information of China (English)

    WANG PEI

    2006-01-01

    @@ In recent years, Changsha,the capital city of Hunan Province, has become famous across China for its innovative TV channel, in particular the cultural phenomenon of the Super Girl talent show. And as far as culture goes, Hunan TV is merely a reflection of a renaissance happening in the city. Animation, music halls, drama festivals and a famous book market are just some of the city's cultural sectors that are benefiting from the fame and notoriety of the Super Girl show.

  16. The formation of super-rings

    CERN Document Server

    Tenorio-Tagle, G

    1980-01-01

    The author has calculated the collision of a small neutral cloud (surface density approximately 10/sup 19/ cm/sup -2/) with a constant density galactic disk. Through the collision, a large amount of energy is deposited in a small volume of the galaxy, resulting in a supersonic expansion of very hot (10/sup 6/-10/sup 7/K) gas into the Galaxy and out of the galactic disk. The expansion generates a large cavity (a super-ring) with physical characteristics (diameter, velocity of expansion, etc.) in agreement with the observations, and a large volume of hot low-density gas with properties similar to those of the observed coronal gas. (31 refs).

  17. Nonlinear Super Integrable Couplings of Super Dirac Hierarchy and Its Super Hamiltonian Structures

    Institute of Scientific and Technical Information of China (English)

    尤福财

    2012-01-01

    We construct nonlinear super integrable couplings of the super integrable Dirac hierarchy based on an enlarged matrix Lie superalgebra. Then its super Hamiltonian structure is furnished by super trace identity. As its reduction, we gain the nonlinear integrable couplings of the classical integrable Dirac hierarchy.

  18. Lightweight, High Strength Metals With Enhanced Radiation Shielding - Technology Advancing Partnerships Challenge Project

    Science.gov (United States)

    Wright, Maria Clara (Compiler)

    2015-01-01

    The Technology Advancing Partnership (TAP) Challenge will seek to foster innovation throughout the Center by allowing the KSC workforce to identify a specific technology idea that needs improvement and to then work with an external partner to develop that technology. This Challenge will enable competitive partnerships with outside entities that will increase the value by bringing leveraged resources. The selected proposal from the University of Florida will develop new lightweight technologies with radiation mitigation for spacecraft.

  19. Geopolymerization of lightweight aggregate waste

    Directory of Open Access Journals (Sweden)

    Labrincha, J. A.

    2008-09-01

    Full Text Available Geopolymerization is a viable way to process and re-use alumino-silicate industrial waste while producing highstrength, high chemical inertia materials that can effectively immobilize other industrial by-products, and even hazardous waste. In this study industrial waste from different stages of the manufacture of lightweight expanded clay aggregate was characterized for its possible transformation, via alkali activation, to geopolymers. The ultimate aim was to assess the possibility of using such geopolymers to develop thermal and acoustic insulation panels. The containment of hazardous materials is another important application for these new materials. Geopolymers were prepared for this study with different particles size distributions and activator concentrations. Their mechanical properties, composition and microstructure were characterized and a material with promising insulating properties was produced. A preliminary analysis was conducted of the salt formation observed in these geopolymers, the chief drawback to their use.La geopolimerización es una manera viable para procesar y agregar valor a los residuos industriales de alumino-silicato dando lugar a materiales con elevadas resistencias mecánmicas, alta inercia química y que permiten encapsular otros residuos, incluso peligrosos. Los residuos industriales que proceden de diversos tipos de arcillas para la fabricación de áridos ligeros se han caracterizado para la producción de geopolímeros mediante el proceso de ataque alcalino. Su incorporación en una matriz geopolimérica permite la posibilidad de desarrollo de paneles de aislamiento (térmico y acústico. Además, la inmovilización de materiales peligrosos es un logro adicional importante. Los geopolímeros se han producido con fórmulas diferentes y se han caracterizado sus propiedades mecánicas, composición y microestructura, para dar lugar a una composición interesante con propiedades aislantes. Se ha llevado a cabo

  20. The Design of a Lightweight RFID Middleware

    Directory of Open Access Journals (Sweden)

    Fengqun Lin

    2009-10-01

    Full Text Available Radio Frequency Identification (RFID middleware is often regarded as the central nervous system of RFID systems. In this paper, a lightweight RFID middleware is designed and implemented without the need of an Application Level Events (ALE structure, and its implementation process is described using a typical commerical enterprise. A short review of the current RFID middleware research and development is also included. The characteristics of RFID middleware are presented with a two-centric framework. The senarios of RFID data integration based on the simplified structure are provided to illuminats the design and implementation of the lightweight middleware structure and its development process. The lightweight middleware is easy to maintain and extend because of the simplified and streamlined structure and the short development cycle.

  1. A lightweight shape-memory magnesium alloy.

    Science.gov (United States)

    Ogawa, Yukiko; Ando, Daisuke; Sutou, Yuji; Koike, Junichi

    2016-07-22

    Shape-memory alloys (SMAs), which display shape recovery upon heating, as well as superelasticity, offer many technological advantages in various applications. Those distinctive behaviors have been observed in many polycrystalline alloy systems such as nickel titantium (TiNi)-, copper-, iron-, nickel-, cobalt-, and Ti-based alloys but not in lightweight alloys such as magnesium (Mg) and aluminum alloys. Here we present a Mg SMA showing superelasticity of 4.4% at -150°C and shape recovery upon heating. The shape-memory properties are caused by reversible martensitic transformation. This Mg alloy includes lightweight scandium, and its density is about 2 grams per cubic centimeter, which is one-third less than that of practical TiNi SMAs. This finding raises the potential for development and application of lightweight SMAs across a number of industries.

  2. Exploring Energy Efficiency of Lightweight Block Ciphers

    DEFF Research Database (Denmark)

    Banik, Subhadeep; Bogdanov, Andrey; Regazzoni, Francesco

    2016-01-01

    lightweight block ciphers, and thereby try to predict the optimal value of r at which an r-round unrolled architecture for a cipher is likely to be most energy efficient. We also try to relate our results to some physical design parameters like the signal delay across a round and algorithmic parameters like......In the last few years, the field of lightweight cryptography has seen an influx in the number of block ciphers and hash functions being proposed. One of the metrics that define a good lightweight design is the energy consumed per unit operation of the algorithm. For block ciphers, this operation...... is the encryption of one plaintext. By studying the energy consumption model of a CMOS gate, we arrive at the conclusion that the energy consumed per cycle during the encryption operation of an r-round unrolled architecture of any block cipher is a quadratic function in r. We then apply our model to 9 well known...

  3. Infinte Periodic Structure of Lightweight Elements

    DEFF Research Database (Denmark)

    Domadiya, Parthkumar Gandalal; Andersen, Lars Vabbersgaard; Sorokin, Sergey

    2013-01-01

    Lightweight wooden structures have become more popular as a sustainable, environmental- friendly and cost-effective alternative to concrete, steel and masonry buildings. However, there are certain drawbacks regarding noise and vibration due to the smaller weight and stiffness of wooden buildings...... for proper dynamic assessment of lightweight buildings. Instead, this paper discusses and compares the use of finite element analysis and a wave approach based on Floquet theory. The present analysis has focus on the effect of periodicity on vibration transmission within semi-infinite beam structures. Two....... Furthermore, lightweight building elements are typically periodic structures that behave as filters for sound propagation within certain frequency ranges (stop bands), thus only allowing transmission within the pass bands. Hence, traditional methods based on statistical energy analysis cannot be used...

  4. LIGHT-WEIGHT LOAD-BEARING STRUCTURE

    DEFF Research Database (Denmark)

    2009-01-01

    The invention relates to a light-weight load-bearing structure (1) with optimized compression zone (2), where along one or more compression zones (2) in the structure (1) to be cast a core (3) of strong concrete is provided, which core (3) is surrounded by concrete of less strength (4) compared...... to the core (3) of strong concrete. The invention also relates to a method of casting of light-weight load-bearing structures (1) with optimized compression zone (2) where one or more channels, grooves, ducts, pipes and/or hoses (5) formed in the load-bearing structure (1) serves as moulds for moulding one...... or more cores (3) of strong concrete in the light-weight load-bearing structure (1)....

  5. Deforming super Riemann surfaces with gravitinos and super Schottky groups

    Energy Technology Data Exchange (ETDEWEB)

    Playle, Sam [Dipartimento di Fisica, Università di Torino and INFN, Sezione di Torino,Via P. Giuria 1, I-10125 Torino (Italy)

    2016-12-12

    The (super) Schottky uniformization of compact (super) Riemann surfaces is briefly reviewed. Deformations of super Riemann surface by gravitinos and Beltrami parameters are recast in terms of super Schottky group cohomology. It is checked that the super Schottky group formula for the period matrix of a non-split surface matches its expression in terms of a gravitino and Beltrami parameter on a split surface. The relationship between (super) Schottky groups and the construction of surfaces by gluing pairs of punctures is discussed in an appendix.

  6. Ultra-lightweight, Low Scatter, Large Mirror Technology

    Science.gov (United States)

    Bennett, H. E.

    2006-01-01

    A technique is being developed to fabricate a prototype lightweight composite mirror one meter in diameter. The mandrel, on which the composite mirror will be laid up, is an ultra low expansion quartz glass, TSG, whose thermal expansion coefficient, 10(exp -7)/ degC or less, is similar to that for the composite material itself. The mandrel surface will be super-polished to 6-8 A rms or better, resulting in ten times less scattered light in the visible region than is found in typical astronomical mirrors. We have shown experimentally that mandrel micro-roughnesses of this order can be successfully replicated on composite faceplates. The faceplate is very tough, and does not fracture like a thin glass faceplate. It will be supported by actuators alone, not by the edge of the mirror mount, to avoid non-uniform or non-symmetric influence functions. BOR developed actuators are designed for atmospheric correction, maintenance of optical figure, and minor tip tilt. They have a throw of a centimeter, can be controlled remotely, and have a response time of 1/2 msec. The piezoelectric part of the actuator operates in the 30-70 V range and the differential screw portion has a linearity of about +/-0.1 microns.

  7. Southern Regional Center for Lightweight Innovative Design

    Energy Technology Data Exchange (ETDEWEB)

    Horstemeyer, Mark F. [Mississippi State Univ., Mississippi State, MS (United States); Wang, Paul [Mississippi State Univ., Mississippi State, MS (United States)

    2011-12-27

    The three major objectives of this Phase III project are: To develop experimentally validated cradle-to-grave modeling and simulation tools to optimize automotive and truck components for lightweighting materials (aluminum, steel, and Mg alloys and polymer-based composites) with consideration of uncertainty to decrease weight and cost, yet increase the performance and safety in impact scenarios; To develop multiscale computational models that quantify microstructure-property relations by evaluating various length scales, from the atomic through component levels, for each step of the manufacturing process for vehicles; and To develop an integrated K-12 educational program to educate students on lightweighting designs and impact scenarios.

  8. Environmental assessment of lightweight electric vehicles

    CERN Document Server

    Egede, Patricia

    2017-01-01

    This monograph adresses the challenge of the environmental assessment of leightweight electric vehicles. It poses the question whether the use of lightweight materials in electric vehicles can reduce the vehicles’ environmental impact and compares the environmental performance of a lightweight electric vehicle (LEV) to other types of vehicles. The topical approach focuses on methods from life cycle assessment (LCA), and the book concludes with a comprehensive concept on the environmental assessment of LEVs. The target audience primarily comprises LCA practitioners from research institutes and industry, but it may also be beneficial for graduate students specializing in the field of environmental assessment.

  9. Braiding properties of the N=1 super-conformal blocks (Ramond sector)

    CERN Document Server

    Chorazkiewicz, Damian; Jaskolski, Zbigniew

    2011-01-01

    Using a super scalar field representation of the chiral vertex operators we develop a general method of calculating braiding matrices for all types of N=1 super-conformal 4-point blocks involving Ramond external weights. We give explicit analytic formulae in a number of cases.

  10. High-Pressure Lightweight Thrusters

    Science.gov (United States)

    Holmes, Richard; McKechnie, Timothy; Shchetkovskiy, Anatoliy; Smirnov, Alexander

    2013-01-01

    Returning samples of Martian soil and rock to Earth is of great interest to scientists. There were numerous studies to evaluate Mars Sample Return (MSR) mission architectures, technology needs, development plans, and requirements. The largest propulsion risk element of the MSR mission is the Mars Ascent Vehicle (MAV). Along with the baseline solid-propellant vehicle, liquid propellants have been considered. Similar requirements apply to other lander ascent engines and reaction control systems. The performance of current state-ofthe- art liquid propellant engines can be significantly improved by increasing both combustion temperature and pressure. Pump-fed propulsion is suggested for a single-stage bipropellant MAV. Achieving a 90-percent stage propellant fraction is thought to be possible on a 100-kg scale, including sufficient thrust for lifting off Mars. To increase the performance of storable bipropellant rocket engines, a high-pressure, lightweight combustion chamber was designed. Iridium liner electrodeposition was investigated on complex-shaped thrust chamber mandrels. Dense, uniform iridium liners were produced on chamber and cylindrical mandrels. Carbon/carbon composite (C/C) structures were braided over iridium-lined mandrels and densified by chemical vapor infiltration. Niobium deposition was evaluated for forming a metallic attachment flange on the carbon/ carbon structure. The new thrust chamber was designed to exceed state-of-the-art performance, and was manufactured with an 83-percent weight savings. High-performance C/Cs possess a unique set of properties that make them desirable materials for high-temperature structures used in rocket propulsion components, hypersonic vehicles, and aircraft brakes. In particular, more attention is focused on 3D braided C/Cs due to their mesh-work structure. Research on the properties of C/Cs has shown that the strength of composites is strongly affected by the fiber-matrix interfacial bonding, and that weakening

  11. Paper Sludge Reuse in Lightweight Aggregates Manufacturing.

    Science.gov (United States)

    Chen, How-Ji; Hsueh, Ying-Chih; Peng, Ching-Fang; Tang, Chao-Wei

    2016-10-27

    The lightweight aggregates used by the civil engineering market are sintered at a high temperature, about 1200 °C. In times of high energy prices and regulation of carbon dioxide emissions, lightweight aggregate products of the high-temperature process in sales marketing are not readily accepted. This study developed a sintered-type paper sludge lightweight aggregate. In order to reduce energy consumption, substitution of some reservoir sediment clay in paper sludge substitutes is to be expected. The study used two types of paper sludge (green clay paper sludge and paper pulp sludge). The sintering temperature was reduced effectively as the green clay paper sludge was substituted for some of the reservoir sediment clay, and the optimum substitute ranges of green clay paper sludge were 10%-50%. The optimum substitute ranges of the paper pulp sludge were 10%-40%. Test results show that the properties of aggregates have a particle density of 0.66-1.69 g/cm³, a water absorption of 5%-30%, and a loss on ignition of 10%-43%. The loss on ignition of aggregate became greater with the increase in paper sludge content. This means that the calorific value provided by the paper sludge will increase as paper sludge content increases. Paper sludge can therefore be considered a good material to provide heat energy for sintering lightweight aggregate.

  12. Lightweight solar concentrator structures, phase 2

    Science.gov (United States)

    Williams, Brian E.; Kaplan, Richard B.

    1993-01-01

    This report summarizes the results of the program conducted by Ultramet under SBIR Phase 2 Contract NAS3-25418. The objective of this program was to develop lightweight materials and processes for advanced high accuracy Space Solar Concentrators using rigidized foam for the substrate structure with an integral optical surface.

  13. Method of fabricating lightweight honeycomb structures

    Science.gov (United States)

    Goela, Jitendra S. (Inventor); Pickering, Michael (Inventor); Taylor, Raymond L. (Inventor)

    1992-01-01

    A process is disclosed for fabricating lightweight honeycomb type structures out of material such as silicon carbide (SiC) and silicon (S). The lightweight structure consists of a core to define the shape and size of the structure. The core is coated with an appropriate deposit such as SiC or Si to give the lightweight structure strength and stiffness and for bonding the lightweight structure to another surface. The core is fabricated from extremely thin ribs of appropriately stiff and strong material such as graphite. First, a graphite core consisting of an outer hexagonal cell with six inner triangular cells is constructed from the graphite ribs. The graphite core may be placed on the back-up side of a SiC faceplate and then coated with SiC to produce a monolithic structure without the use of any bonding agent. Cores and methods for the fabrication thereof in which the six inner triangular cells are further divided into a plurality of cells are also disclosed.

  14. A Lightweight Mobile RSVP for Unicast

    Institute of Scientific and Technical Information of China (English)

    CHEN Wen; LEI Fei-yu; CHEN Xi; WANG Wei-nong

    2005-01-01

    This paper presents a lighter protocol, and it removes the multicast burdens from RSVP to adapt to unicast applications. At the same time, when RSVP is used in wireless networks, some issues about mobility raise popular concerns. The proposed protocol a lightweight mobile RSVP protocol, solves the problems by the following mechanisms:changeless flow identifier, a new state management and "refresh" mechanism.

  15. Lightweight concrete with enhanced neutron shielding

    Energy Technology Data Exchange (ETDEWEB)

    Brindza, Paul Daniel; Metzger, Bert Clayton

    2016-09-13

    A lightweight concrete containing polyethylene terephthalate in an amount of 20% by total volume. The concrete is enriched with hydrogen and is therefore highly effective at thermalizing neutrons. The concrete can be used independently or as a component of an advanced neutron radiation shielding system.

  16. Cryptanalysis of Some Lightweight Symmetric Ciphers

    DEFF Research Database (Denmark)

    Abdelraheem, Mohamed Ahmed Awadelkareem Mohamed Ahmed

    on a variant of PRESENT with identical round keys. We propose a new attack named the Invariant Subspace Attack that was specifically mounted against the lightweight block cipher PRINTcipher. Furthermore, we mount several attacks on a recently proposed stream cipher called A2U2....

  17. FY 2012 Lightweight Materials Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-04-15

    The FY 2012 Annual Progress Report for Lightweight Materials provides a detailed description of the activities and technical accomplishments which focuses on the development and validation of advanced materials and manufacturing technologies to significantly reduce light and heavy duty vehicle weight without compromising other attributes such as safety, performance, recyclability, and cost.

  18. Meshed-Pumpkin Super-Pressure Balloon Design

    Science.gov (United States)

    Jones, Jack; Yavrouian, Andre

    2003-01-01

    An improved, lightweight design has been proposed for super-pressure balloons used to carry scientific instruments at high altitudes in the atmosphere of Earth for times as long as 100 days. [A super-pressure balloon is one in which the pressure of the buoyant gas (typically, helium) is kept somewhat above ambient pressure in order to maintain approximately constant density and thereby regulate the altitude.] The proposed design, called "meshed pumpkin," incorporates the basic concept of the pumpkin design, which is so named because of its appearance. The pumpkin design entails less weight than does a spherical design, and the meshed-pumpkin design would reduce weight further. The basic idea of the meshed-pumpkin design is to reinforce the membrane of a pumpkin balloon by attaching a strong, lightweight fabric mesh to its outer surface. The reinforcement would make it possible to reduce the membrane mass to one-third or less of that of the basic pumpkin design while retaining sufficient strength to enable the balloon to remain at approximately constant altitude for months.

  19. Raspberry Pi super cluster

    CERN Document Server

    Dennis, Andrew K

    2013-01-01

    This book follows a step-by-step, tutorial-based approach which will teach you how to develop your own super cluster using Raspberry Pi computers quickly and efficiently.Raspberry Pi Super Cluster is an introductory guide for those interested in experimenting with parallel computing at home. Aimed at Raspberry Pi enthusiasts, this book is a primer for getting your first cluster up and running.Basic knowledge of C or Java would be helpful but no prior knowledge of parallel computing is necessary.

  20. SuperQuant

    DEFF Research Database (Denmark)

    Gorshkov, Vladimir; Verano-Braga, Thiago; Kjeldsen, Frank

    2015-01-01

    SuperQuant is a quantitative proteomics data processing approach that uses complementary fragment ions to identify multiple co-isolated peptides in tandem mass spectra allowing for their quantification. This approach can be applied to any shotgun proteomics data set acquired with high mass accura...... of the same proteins were close to the values typical for other precursor ion-based quantification methods. The raw data is deposited to ProteomeXchange (PXD001907). The developed node is available for testing at https://github.com/caetera/SuperQuantNode....

  1. Vehicle Lightweighting: 40% and 45% Weight Savings Analysis: Technical Cost Modeling for Vehicle Lightweighting

    Energy Technology Data Exchange (ETDEWEB)

    Mascarin, Anthony [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hannibal, Ted [Idaho National Lab. (INL), Idaho Falls, ID (United States); Raghunathan, Anand [Idaho National Lab. (INL), Idaho Falls, ID (United States); Ivanic, Ziga [Idaho National Lab. (INL), Idaho Falls, ID (United States); Francfort, James [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-04-01

    The U.S. Department of Energy’s Vehicle Technologies Office, Materials area commissioned a study to model and assess manufacturing economics of alternative design and production strategies for a series of lightweight vehicle concepts. The strategic targets were a 40% and a 45% mass reduction relative to a standard North American midsize passenger sedan at an effective cost of $3.42 per pound (lb) saved. The baseline vehicle was an average of several available vehicles in this class. Mass and cost breakdowns from several sources were used, including original equipment manufacturers’ (OEMs’) input through U.S. Department of Energy’s Vehicle Technologies Office programs and public presentations, A2Mac1 LLC’s teardown information, Lotus Engineering Limited and FEV, Inc. breakdowns in their respective lightweighting studies, and IBIS Associates, Inc.’s decades of experience in automotive lightweighting and materials substitution analyses. Information on lightweighting strategies in this analysis came from these same sources and the ongoing U.S. Department of Energy-funded Vehma International of America, Inc. /Ford Motor Company Multi-Material Lightweight Prototype Vehicle Demonstration Project, the Aluminum Association Transportation Group, and many United States Council for Automotive Research’s/United States Automotive Materials Partnership LLC lightweight materials programs.

  2. "Super Roman Pots"

    CERN Multimedia

    CERN PhotoLab

    1975-01-01

    Remotely controlled re-entrant vacuum vessels, with very thin (0.17 mm) central windows, that will be installed in each downstream arm of intersection I-8. Detectors for a coming physics experiment, placed inside these "Super Roman Pots", can be moved very close to the circulating ISR beams.

  3. A Super Roman Pot

    CERN Multimedia

    1975-01-01

    Remotely controlled re-entrant vacuum vessels, with very thin (0.17 mm) central windows, that were installed in each downstream arm of the ISR intersection I-8. Detectors placed inside these Super Roman Pots could be moved very close to the circulating ISR beams. (See Annual Report 1974 p. 110.)

  4. Cryostable lightweight frit bonded silicon mirror

    Science.gov (United States)

    Anthony, F.; McCarter, D.; Tangedahl, M.; Content, D.

    The excellent polishability, low density and relatively high stiffness of silicon make it an attractive candidate for optical applications that require superior performance. Assembly of silicon details by means of glass frit bonding permits significant light weighting thus enhancing the benefit of silicon mirrors. To demonstrate the performance potential, a small lightweight glass frit bonded silicon mirror was fabricated and tested for cryoability. The test mirror was 12.5cm in diameter with a 60cm spherical radius and a maximum thickness, at the perimeter, of 2.5cm. A machined silicon core was used to stiffen the two face sheets of the silicon sandwich. These three elements were assembled, by glass frit bonding, to form the substrate that was polished. The experimental evaluation in a liquid nitrogen cryostat, demonstrated cryostability performance significantly better than required by the mirror specification. Key WordsCryostable, Lightweight, Silicon, Frit Bond, Spherical, Mirror

  5. Lightweight composite fighting cover prototype development program

    Energy Technology Data Exchange (ETDEWEB)

    Wrenn, G.E. Jr.; Frame, B.J.; Gwaltney, R.C.; Akerman, M.A.

    1996-07-01

    The U.S. Army Field Assistance Science and Technology Program requested Oak Ridge National Laboratory (ORNL) to demonstrate the use of lightweight composite materials in construction of overhead covers for reinforced infantry fighting positions. In recent years, ORNL researchers have designed and tested several concepts for lightweight ballistic protection structures, and they have developed numerous prototype composite structures for military and civilian applications. In the current program, composite panel designs and materials are tested and optimized to meet anticipated static and dynamic load conditions for the overhead cover structure. Ten prototype composite covers were built at ORNL for use in Army field tests. Each composite cover has a nominal surface area of 12 ft[sup 2] and a nominal weight of 8 lb. Four of the prototypes are made with folding sections to improve their handling characteristics. The composite covers exhibit equivalent performance in Army field tests to covers made with conventional materials that weigh four times as much.

  6. Lightweight Service Oriented Architecture for Pervasive Computing

    CERN Document Server

    Tigli, Jean-Yves; Rey, Gaetan; Hourdin, Vincent; Riveill, Michel

    2011-01-01

    Pervasive computing appears like a new computing era based on networks of objects and devices evolving in a real world, radically different from distributed computing, based on networks of computers and data storages. Contrary to most context-aware approaches, we work on the assumption that pervasive software must be able to deal with a dynamic software environment before processing contextual data. After demonstrating that SOA (Service oriented Architecture) and its numerous principles are well adapted for pervasive computing, we present our extended SOA model for pervasive computing, called Service Lightweight Component Architecture (SLCA). SLCA presents various additional principles to meet completely pervasive software constraints: software infrastructure based on services for devices, local orchestrations based on lightweight component architecture and finally encapsulation of those orchestrations into composite services to address distributed composition of services. We present a sample application of t...

  7. Lightweight Protective Coatings For Titanium Alloys

    Science.gov (United States)

    Wiedemann, Karl E.; Taylor, Patrick J.; Clark, Ronald K.

    1992-01-01

    Lightweight coating developed to protect titanium and titanium aluminide alloys and titanium-matrix composite materials from attack by environment when used at high temperatures. Applied by sol-gel methods, and thickness less than 5 micrometers. Reaction-barrier and self-healing diffusion-barrier layers combine to protect titanium alloy against chemical attack by oxygen and nitrogen at high temperatures with very promising results. Can be extended to protection of other environmentally sensitive materials.

  8. Aladin Lite: Lightweight sky atlas for browsers

    Science.gov (United States)

    Boch, Thomas

    2014-02-01

    Aladin Lite is a lightweight version of the Aladin tool, running in the browser and geared towards simple visualization of a sky region. It allows visualization of image surveys (JPEG multi-resolution HEALPix all-sky surveys) and permits superimposing tabular (VOTable) and footprints (STC-S) data. Aladin Lite is powered by HTML5 canvas technology and is easily embeddable on any web page and can also be controlled through a Javacript API.

  9. LUCA:Lightweight Ubiquitous Computing Architecture

    Institute of Scientific and Technical Information of China (English)

    SUN Dao-qing; CAO Qi-ying

    2009-01-01

    Lightweight ubiquitous computing security architecture was presented. Lots of our recent researches have been integrated in this architecture. And the main current researches in the related area have also been absorbed. The main attention of this paper was providing a compact and realizable method to apply ubiquitous computing into our daily lives under sufficient secure guarantee. At last, the personal intelligent assistant system was presented to show that this architecture was a suitable and realizable security mechanism in solving the ubiquitous computing problems.

  10. GLUE!: An Architecture for the Integration of External Tools in Virtual Learning Environments

    Science.gov (United States)

    Alario-Hoyos, Carlos; Bote-Lorenzo, Miguel L.; Gomez-Sanchez, Eduardo; Asensio-Perez, Juan I.; Vega-Gorgojo, Guillermo; Ruiz-Calleja, Adolfo

    2013-01-01

    The integration of external tools in Virtual Learning Environments (VLEs) aims at enriching the learning activities that educational practitioners may design and enact. This paper presents GLUE!, an architecture that enables the lightweight integration of multiple existing external tools in multiple existing VLEs. GLUE! fosters this integration by…

  11. Southern Regional Center for Lightweight Innovative Design

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Paul T. [Mississippi State Univ., Mississippi State, MS (United States)

    2012-12-01

    The Southern Regional Center for Lightweight Innovative Design (SRCLID) has developed an experimentally validated cradle-to-grave modeling and simulation effort to optimize automotive components in order to decrease weight and cost, yet increase performance and safety in crash scenarios. In summary, the three major objectives of this project are accomplished: To develop experimentally validated cradle-to-grave modeling and simulation tools to optimize automotive and truck components for lightweighting materials (aluminum, steel, and Mg alloys and polymer-based composites) with consideration of uncertainty to decrease weight and cost, yet increase the performance and safety in impact scenarios; To develop multiscale computational models that quantify microstructure-property relations by evaluating various length scales, from the atomic through component levels, for each step of the manufacturing process for vehicles; and To develop an integrated K-12 educational program to educate students on lightweighting designs and impact scenarios. In this final report, we divided the content into two parts: the first part contains the development of building blocks for the project, including materials and process models, process-structure-property (PSP) relationship, and experimental validation capabilities; the second part presents the demonstration task for Mg front-end work associated with USAMP projects.

  12. Engineering properties of high strength lightweight concrete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-08-01

    The strength to weight ratio of high strength lightweight concrete is not its only advantage. The artificial lightweight aggregate combines physically and, to a lesser extent, chemically with the surrounding cement matrix to produce an impermeable and durable concrete. The engineering properties of the concrete are sensitive to the proportions and nature of its constituents, and to its production methods. Supplementary cementing materials and chemical admixtures are used to develop the increased strength and durability. Thermal movements, shrinkage and creep are within workable limits. Fatigue resistance is probably at least as good as that achieved by equivalent strength normal density concretes but there is limited data on this topic. Deleterious effects of admixtures supplied in high dosages have not been identified but neither have they been investigated. The relationship between the tensile strength of the material and its uniaxial compressive strength is not robust. The shear capacity of structural elements is not adequately covered by most existing design codes. In common with all concretes, the stability of high strength lightweight concrete is reduced when water retained within it freezes or vaporises. A satisfactory freeze thaw behaviour can be readily achieved but, under fire conditions, the impermeability of the cement matrix limits the venting of water vapour at the concrete surface. Explosive failures can result. (Author)

  13. Southern Regional Center for Lightweight Innovative Design

    Energy Technology Data Exchange (ETDEWEB)

    None

    2012-08-24

    The Southern Regional Center for Lightweight Innovative Design (SRCLID) has developed an experimentally validated cradle-to-grave modeling and simulation effort to optimize automotive components in order to decrease weight and cost, yet increase performance and safety in crash scenarios. In summary, the three major objectives of this project are accomplished: To develop experimentally validated cradle-to-grave modeling and simulation tools to optimize automotive and truck components for lightweighting materials (aluminum, steel, and Mg alloys and polymer-based composites) with consideration of uncertainty to decrease weight and cost, yet increase the performance and safety in impact scenarios; To develop multiscale computational models that quantify microstructure-property relations by evaluating various length scales, from the atomic through component levels, for each step of the manufacturing process for vehicles; and To develop an integrated K-12 educational program to educate students on lightweighting designs and impact scenarios. In this final report, we divided the content into two parts: the first part contains the development of building blocks for the project, including materials and process models, process-structure-property (PSP) relationship, and experimental validation capabilities; the second part presents the demonstration task for Mg front-end work associated with USAMP projects.

  14. SuperSegger

    DEFF Research Database (Denmark)

    Stylianidou, Stella; Brennan, Connor; Nissen, Silas B

    2016-01-01

    -colonies with many cells, facilitating the analysis of cell-cycle dynamics in bacteria as well as cell-contact mediated phenomena. This package has a range of built-in capabilities for characterizing bacterial cells, including the identification of cell division events, mother, daughter, and neighboring cells......Many quantitative cell biology questions require fast yet reliable automated image segmentation to identify and link cells from frame-to-frame, and characterize the cell morphology and fluorescence. We present SuperSegger, an automated MATLAB-based image processing package well......-suited to quantitative analysis of high-throughput live-cell fluorescence microscopy of bacterial cells. SuperSegger incorporates machine-learning algorithms to optimize cellular boundaries and automated error resolution to reliably link cells from frame-to-frame. Unlike existing packages, it can reliably segment micro...

  15. NASA Super Pressure Balloon

    Science.gov (United States)

    Fairbrother, Debbie

    2017-01-01

    NASA is in the process of qualifying the mid-size Super Pressure Balloon (SPB) to provide constant density altitude flight for science investigations at polar and mid-latitudes. The status of the development of the 18.8 million cubic foot SPB capable of carrying one-tone of science to 110,000 feet, will be given. In addition, the operating considerations such as launch sites, flight safety considerations, and recovery will be discussed.

  16. Super-diversité

    NARCIS (Netherlands)

    Crul, M.R.J.; Schneider, J.; Lelie, F.

    2013-01-01

    Le concept de super-diversité, en cernant les conditions d'un scénario 'avenir optimiste, offre un nouvel éclairage au débat sur l'intégration. Nous sommes à la croisée des chemins. Cette étude comparative internationale montre qu'un avenir souriant se profile dans les villes qui donnent des chances

  17. Performing the Super Instrument

    DEFF Research Database (Denmark)

    Kallionpaa, Maria

    2016-01-01

    The genre of contemporary classical music has seen significant innovation and research related to new super, hyper, and hybrid instruments, which opens up a vast palette of expressive potential. An increasing number of composers, performers, instrument designers, engineers, and computer programmers...... provides the performer extensive virtuoso capabilities in terms of instrumental range, harmony, timbre, or spatial, textural, acoustic, technical, or technological qualities. The discussion will be illustrated by a composition case study involving augmented musical instrument electromagnetic resonator...

  18. Performing the Super Instrument

    DEFF Research Database (Denmark)

    Kallionpaa, Maria

    2016-01-01

    provides the performer extensive virtuoso capabilities in terms of instrumental range, harmony, timbre, or spatial, textural, acoustic, technical, or technological qualities. The discussion will be illustrated by a composition case study involving augmented musical instrument electromagnetic resonator......The genre of contemporary classical music has seen significant innovation and research related to new super, hyper, and hybrid instruments, which opens up a vast palette of expressive potential. An increasing number of composers, performers, instrument designers, engineers, and computer programmers...

  19. Characterising Super-Earths

    Directory of Open Access Journals (Sweden)

    Valencia D.

    2011-02-01

    Full Text Available The era of Super-Earths has formally begun with the detection of transiting low-mass exoplanets CoRoT-7b and GJ 1214b. In the path of characterising super-Earths, the first step is to infer their composition. While the discovery data for CoRoT-7b, in combination with the high atmospheric mass loss rate inferred from the high insolation, suggested that it was a rocky planet, the new proposed mass values have widened the possibilities. The combined mass range 1−10 M⊕ allows for a volatile-rich (and requires it if the mass is less than 4 M⊕ , an Earth-like or a super-Mercury-like composition. In contrast, the radius of GJ 1214b is too large to admit a solid composition, thus it necessarily to have a substantial gas layer. Some evidence suggests that within this gas layer H/He is a small but non-negligible component. These two planets are the first of many transiting low-mass exoplanets expected to be detected and they exemplify the limitations faced when inferring composition, which come from the degenerate character of the problem and the large error bars in the data.

  20. Super Fuzzy Matrices and Super Fuzzy Models for Social Scientists

    CERN Document Server

    Kandasamy, W B Vasantha; Amal, K

    2008-01-01

    This book introduces the concept of fuzzy super matrices and operations on them. This book will be highly useful to social scientists who wish to work with multi-expert models. Super fuzzy models using Fuzzy Cognitive Maps, Fuzzy Relational Maps, Bidirectional Associative Memories and Fuzzy Associative Memories are defined here. The authors introduce 13 multi-expert models using the notion of fuzzy supermatrices. These models are described with illustrative examples. This book has three chapters. In the first chaper, the basic concepts about super matrices and fuzzy super matrices are recalled. Chapter two introduces the notion of fuzzy super matrices adn their properties. The final chapter introduces many super fuzzy multi expert models.

  1. Super-quantum curves from super-eigenvalue models

    CERN Document Server

    Ciosmak, Paweł; Manabe, Masahide; Sułkowski, Piotr

    2016-01-01

    In modern mathematical and theoretical physics various generalizations, in particular supersymmetric or quantum, of Riemann surfaces and complex algebraic curves play a prominent role. We show that such supersymmetric and quantum generalizations can be combined together, and construct supersymmetric quantum curves, or super-quantum curves for short. Our analysis is conducted in the formalism of super-eigenvalue models: we introduce $\\beta$-deformed version of those models, and derive differential equations for associated $\\alpha/\\beta$-deformed super-matrix integrals. We show that for a given model there exists an infinite number of such differential equations, which we identify as super-quantum curves, and which are in one-to-one correspondence with, and have the structure of, super-Virasoro singular vectors. We discuss potential applications of super-quantum curves and prospects of other generalizations.

  2. Super-quantum curves from super-eigenvalue models

    Science.gov (United States)

    Ciosmak, Paweł; Hadasz, Leszek; Manabe, Masahide; Sułkowski, Piotr

    2016-10-01

    In modern mathematical and theoretical physics various generalizations, in particular supersymmetric or quantum, of Riemann surfaces and complex algebraic curves play a prominent role. We show that such supersymmetric and quantum generalizations can be combined together, and construct supersymmetric quantum curves, or super-quantum curves for short. Our analysis is conducted in the formalism of super-eigenvalue models: we introduce β-deformed version of those models, and derive differential equations for associated α/ β-deformed super-matrix integrals. We show that for a given model there exists an infinite number of such differential equations, which we identify as super-quantum curves, and which are in one-to-one correspondence with, and have the structure of, super-Virasoro singular vectors. We discuss potential applications of super-quantum curves and prospects of other generalizations.

  3. Super-quantum curves from super-eigenvalue models

    Energy Technology Data Exchange (ETDEWEB)

    Ciosmak, Paweł [Faculty of Mathematics, Informatics and Mechanics, University of Warsaw,ul. Banacha 2, 02-097 Warsaw (Poland); Hadasz, Leszek [M. Smoluchowski Institute of Physics, Jagiellonian University,ul. Łojasiewicza 11, 30-348 Kraków (Poland); Manabe, Masahide [Faculty of Physics, University of Warsaw,ul. Pasteura 5, 02-093 Warsaw (Poland); Sułkowski, Piotr [Faculty of Physics, University of Warsaw,ul. Pasteura 5, 02-093 Warsaw (Poland); Walter Burke Institute for Theoretical Physics, California Institute of Technology,1200 E. California Blvd, Pasadena, CA 91125 (United States)

    2016-10-10

    In modern mathematical and theoretical physics various generalizations, in particular supersymmetric or quantum, of Riemann surfaces and complex algebraic curves play a prominent role. We show that such supersymmetric and quantum generalizations can be combined together, and construct supersymmetric quantum curves, or super-quantum curves for short. Our analysis is conducted in the formalism of super-eigenvalue models: we introduce β-deformed version of those models, and derive differential equations for associated α/β-deformed super-matrix integrals. We show that for a given model there exists an infinite number of such differential equations, which we identify as super-quantum curves, and which are in one-to-one correspondence with, and have the structure of, super-Virasoro singular vectors. We discuss potential applications of super-quantum curves and prospects of other generalizations.

  4. Design of ultra-lightweight concrete: towards monolithic concrete structures

    Directory of Open Access Journals (Sweden)

    Yu Qing Liang

    2014-04-01

    Full Text Available This study addresses the development of ultra-lightweight concrete. A moderate strength and an excellent thermal conductivity of the lightweight concrete are set as the design targets. The designed lightweight aggregates concrete is targeted to be used in monolithic concrete façade structure, performing as both load bearing element and thermal insulator. The developed lightweight concrete shows excellent thermal properties, with a low thermal conductivity of about 0.12 W/(m·K; and moderate mechanical properties, with 28-day compressive strengths of about 10-12 N/mm . This combination of values exceeds, to the researchers’ knowledge, the performance of all other lightweight building materials. Furthermore, the developed lightweight concrete possesses excellent durability properties.

  5. Principles and Chief Technologies in Developing Light-weighted Worsted Fabrics

    Institute of Scientific and Technical Information of China (English)

    周启澄

    2001-01-01

    More and more light-weighted fabrics are being required by the market, especially for the worsted manufacture.In the past, such fabrics are produced mainly through changing the structure of woven goods or by using finer yarns. But these possibilities are very limited. In this paper, new devices are discussed: (1) on the yarn level- to use single yarns instead of conventional doubled ones, to decrease number of fibers in yarn cross sections beth during spinning and after finishing; (2) on the fiber level - to use finer fibers in blends with wool and modification of the wool fibers; (3) on the macromolecule level - to stretch the macromolecules in alpha keratin, to get super fine wool fibers.

  6. Lightweight Thermally Stable Multi-Meter Aperture Submillimeter Reflectors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Future astrophysics missions will require lightweight, thermally stable, submillimeter reflectors in sizes of 4m and greater. To date, graphite fiber reinforced...

  7. Laser Additive Manufacturing and Bionics: Redefining Lightweight Design

    Science.gov (United States)

    Emmelmann, C.; Sander, P.; Kranz, J.; Wycisk, E.

    New layer wise manufacturing technologies such as Laser Additive Manufacturing (LAM) allow innovative approaches to product design. Especially for lightweight design in aircraft applications LAM offers new possibilities for load-adapted structures. However, to fully capture lightweight potential of LAM technologies new design guidelines and processes have to be developed. A novel approach to extreme lightweight design is realized by incorporating structural optimization tools, bionic structures and LAM guidelines into one design process. By consequently following this design process designers can achieve lightweight savings in designing new aircraft structures.

  8. Lightweight Rubbery Aerogel Composites for High Performance Protection Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Aspen Aerogels Inc. (AAI) and the Man Vehicle Laboratory (MVL) at the Massachusetts Institute of Technology propose to develop nanostructured, lightweight, rubbery...

  9. Super insulating aerogel glazing

    DEFF Research Database (Denmark)

    Schultz, Jørgen Munthe; Jensen, Karsten Ingerslev; Kristiansen, Finn Harken

    2004-01-01

    Monolithic silica aerogel offers the possibility of combining super insulation and high solar energy transmittance, which has been the background for a previous and a current EU project on research and development of monolithic silica aerogel as transparent insulation in windows. Generally, windows...... form the weakest part of the thermal envelope with respect to heat loss coefficient, but on the other hand also play an important role for passive solar energy utilisation. For window orientations other than south, the net energy balance will be close to or below zero. However, the properties...

  10. Super insulating aerogel glazing

    DEFF Research Database (Denmark)

    Schultz, Jørgen Munthe; Jensen, Karsten Ingerslev; Kristiansen, Finn Harken

    2005-01-01

    This paper describes the application results of a previous and current EU-project on super insulating glazing based on monolithic silica aerogel. Prototypes measuring approx. 55´55 cm2 have been made with 15 mm evacuated aerogel between two layers of low-iron glass. Anti-reflective treatment...... of the glass and a heat-treatment of the aerogel increases the visible quality and the solar energy transmittance. A low-conductive rim seal solution with the required vacuum barrier properties has been developed along with a reliable assembly and evacuation process. The prototypes have a centre heat loss...

  11. Super-heptazethrene

    KAUST Repository

    Zeng, Wangdong

    2016-05-30

    The challenging synthesis of a laterally extended heptazethrene molecule, the super-heptazethrene derivative SHZ-CF3, is reported. This molecule was prepared using a strategy involving a multiple selective intramolecular Friedel–Crafts alkylation followed by oxidative dehydrogenation. Compound SHZ-CF3 exhibits an open-shell singlet diradical ground state with a much larger diradical character compared with the heptazethrene derivatives. An intermediate dibenzo-terrylene SHZ-2H was also obtained during the synthesis. This study provides a new synthetic method to access large-size quinoidal polycyclic hydrocarbons with unique physical properties.

  12. Type Classes for Lightweight Substructural Types

    Directory of Open Access Journals (Sweden)

    Edward Gan

    2015-02-01

    Full Text Available Linear and substructural types are powerful tools, but adding them to standard functional programming languages often means introducing extra annotations and typing machinery. We propose a lightweight substructural type system design that recasts the structural rules of weakening and contraction as type classes; we demonstrate this design in a prototype language, Clamp. Clamp supports polymorphic substructural types as well as an expressive system of mutable references. At the same time, it adds little additional overhead to a standard Damas-Hindley-Milner type system enriched with type classes. We have established type safety for the core model and implemented a type checker with type inference in Haskell.

  13. Longbow: A Lightweight Remote Job Submission Tool

    Directory of Open Access Journals (Sweden)

    James Gebbie-Rayet

    2016-01-01

    Full Text Available We present Longbow, a lightweight console-based remote job submission tool and library. Longbow allows the user to quickly and simply run jobs on high performance computing facilities without leaving their familiar desktop environment. Not only does Longbow greatly simplify the management of compute- intensive jobs for experienced researchers, it also lowers the technical barriers surrounding high perfor-mance computation for the next generation of scientists and engineers. Longbow has already been used to remotely submit jobs in a number of projects and has the potential to redefine the manner in which high performance computers are used.

  14. Lightweight Cryptography for Passive RFID Tags

    DEFF Research Database (Denmark)

    David, Mathieu

    2012-01-01

    among the smallest in the published literature and aims at being implemented on printed electronics RFID tags. Then, we compare different cryptographic primitives based on their key parameters: throughput, area, power consumption and level of security. Our main concern is the integrability...... of an integrator for a particular application. Finally, we conclude that the research for finding robust cryptographic primitive in the branch of lightweight cryptography still has some nice days ahead, and that providing a secure cryptosystem for printed electronics RFID tags remains an open research topic....

  15. ARC Cache: A solution for lightweight Grid sites in ATLAS

    CERN Document Server

    Garonne, Vincent; The ATLAS collaboration

    2016-01-01

    Many Grid sites have the need to reduce operational manpower, and running a storage element consumes a large amount of effort. In addition, setting up a new Grid site including a storage element involves a steep learning curve and large investment of time. For these reasons so-called storage-less sites are becoming more popular as a way to provide Grid computing resources with less operational overhead. ARC CE is a widely-used and mature Grid middleware which was designed from the start to be used on sites with no persistent storage element. Instead, it maintains a local self-managing cache of data which retains popular data for future jobs. As the cache is simply an area on a local posix shared filesystem with no external-facing service, it requires no extra maintenance. The cache can be scaled up as required by increasing the size of the filesystem or adding new filesystems. This paper describes how ARC CE and its cache are an ideal solution for lightweight Grid sites in the ATLAS experiment, and the integr...

  16. 76 FR 42137 - Certain Lightweight Thermal Paper From Germany; Remand Proceedings

    Science.gov (United States)

    2011-07-18

    ... COMMISSION Certain Lightweight Thermal Paper From Germany; Remand Proceedings AGENCY: United States...-1127 concerning certain lightweight thermal paper (``LWTP'') from Germany. For further information... certain lightweight thermal paper from Germany that the Department of Commerce found were sold at...

  17. Quantitative super-resolution microscopy

    NARCIS (Netherlands)

    Harkes, Rolf

    2016-01-01

    Super-Resolution Microscopy is an optical fluorescence technique. In this thesis we focus on single molecule super-resolution, where the position of single molecules is determined. Typically these molecules can be localized with a 10 to 30nm precision. This technique is applied in four different s

  18. Lightweight design of automotive front crossbeam assembly

    Institute of Scientific and Technical Information of China (English)

    Yao Zaiqi; Liu Qiang; Ma Fangwu; Zhao Fuquan; Liu Zongwei; Wang Guan; Wan Yinhui; Li Luoxing

    2012-01-01

    This paper reviews the development course of the front crossbeam assembly for a self-owned brand vehicle model based on lightweight and passive safety performance. Combining with an A00 model variant, the paper details the design of extruded aluminum-alloy front crossbeam assembly from the perspectives of optimal design, performance verifi- cation, lightweight effect and cost control. The following results in the technical and engineering applications have been achieved. The weight of the developed aluminum-alloy crossbeam can be reduced by 51%. The simulated analysis of the collision rigid wall, the 40 % offset hammering as well as the static crush test of energy-absorbing box show that af- ter reasonable materials matching and size optimization of the crossbeam and the energy-absorbing boxes, the level of crash safety can be improved. The price of aluminum-alloy front crossbeam can be lowered by using the extruding die in- stead of the stamping die to reduce the die cost-sharing.

  19. Advances in very lightweight composite mirror technology

    Science.gov (United States)

    Chen, Peter C.; Bowers, Charles W.; Content, David A.; Marzouk, Marzouk; Romeo, Robert C.

    2000-09-01

    We report progress in the development of very lightweight (roll off and several waves (rms optical) of astigmatism, coma, and third-order spherical aberration. These are indications of thermal contraction in an inhomogeneous medium. This inhomogeneity is due to a systematic radial variation in density and fiber/resin ratio induced in composite plies when draped around a small and highly curved mandrel. The figure accuracy is expected to improve with larger size optics and in mirrors with longer radii of curvature. Nevertheless, the present accuracy figure is sufficient for using postfiguring techniques such as ion milling to achieve diffraction-limited performances at optical and UV wavelengths. We demonstrate active figure control using a simple apparatus of low-mass, low-force actuators to correct astigmatism. The optimized replication technique is applied to the fabrication of a 0.6-m-diam mirror with an areal density of 3.2 kg/m2. Our result demonstrates that the very lightweight, large-aperture construction used in radio telescopes can now be applied to optical telescopes.

  20. Super-light concrete decks for building floor slabs

    DEFF Research Database (Denmark)

    Hertz, Kristian Dahl; Castberg, Niels Andreas; Christensen, Jacob

    2014-01-01

    to flexibility, sound insulation and fire resistance compared with present-day prefabricated structures. Full-scale tests and theoretical investigations show that the deck structure performs as intended. Also, that it is possible to assess by calculation the loadbearing capacity in bending and shear, and assess......This paper presents investigations carried out at the Technical University of Denmark (DTU) on a prototype series for a super-lightweight prestressed concrete deck element called the SL-Deck. The intention behind making a new prefabricated deck element is to improve performance with respect...... the pull-out strength of prestressing wires, the fire resistance and the acoustic insulation. Based on the results of the investigations, recommendations are given for further development of the structure before fully automated mass production is established....

  1. Image Super-Resolution Using Deep Convolutional Networks.

    Science.gov (United States)

    Dong, Chao; Loy, Chen Change; He, Kaiming; Tang, Xiaoou

    2016-02-01

    We propose a deep learning method for single image super-resolution (SR). Our method directly learns an end-to-end mapping between the low/high-resolution images. The mapping is represented as a deep convolutional neural network (CNN) that takes the low-resolution image as the input and outputs the high-resolution one. We further show that traditional sparse-coding-based SR methods can also be viewed as a deep convolutional network. But unlike traditional methods that handle each component separately, our method jointly optimizes all layers. Our deep CNN has a lightweight structure, yet demonstrates state-of-the-art restoration quality, and achieves fast speed for practical on-line usage. We explore different network structures and parameter settings to achieve trade-offs between performance and speed. Moreover, we extend our network to cope with three color channels simultaneously, and show better overall reconstruction quality.

  2. FY2014 Lightweight Materials R&D Annual Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-03-01

    The Lightweight Materials research and development (R&D) area within the DOE Vehicle Technologies Office (VTO) provides support and guidance for many cutting-edge automotive technologies under development. Research focuses on addressing critical barriers to commercializing lightweight materials for passenger and commercial vehicles.

  3. Adaptive Backstepping Control of Lightweight Tower Wind Turbine

    DEFF Research Database (Denmark)

    Galeazzi, Roberto; Borup, Kasper Trolle; Niemann, Hans Henrik;

    2015-01-01

    This paper investigates the feasibility of operating a wind turbine with lightweight tower in the full load region exploiting an adaptive nonlinear controller that allows the turbine to dynamically lean against the wind while maintaining nominal power output. The use of lightweight structures...

  4. Anchorage of Main Reinforcement in Lightweight Aggregate Concrete Beams

    DEFF Research Database (Denmark)

    Larsen, Henning

    1999-01-01

    The paper deals with the anchorage of reinforcement bars at end supports in beam component made of lightweight aggregate concrete with open structure.......The paper deals with the anchorage of reinforcement bars at end supports in beam component made of lightweight aggregate concrete with open structure....

  5. Uncertainty and Variation of Vibration in Lightweight Structures

    DEFF Research Database (Denmark)

    Dickow, Kristoffer Ahrens

    2012-01-01

    Multi-family dwellings and offices build from lightweight materials are becoming a cost efficient and environmentally friendly alternative to traditional heavy structures.......Multi-family dwellings and offices build from lightweight materials are becoming a cost efficient and environmentally friendly alternative to traditional heavy structures....

  6. Adaptive Backstepping Control of Lightweight Tower Wind Turbine

    DEFF Research Database (Denmark)

    Galeazzi, Roberto; Borup, Kasper Trolle; Niemann, Hans Henrik

    2015-01-01

    This paper investigates the feasibility of operating a wind turbine with lightweight tower in the full load region exploiting an adaptive nonlinear controller that allows the turbine to dynamically lean against the wind while maintaining nominal power output. The use of lightweight structures for...

  7. 46 CFR 30.10-38 - Lightweight-TB/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Lightweight-TB/ALL. 30.10-38 Section 30.10-38 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS GENERAL PROVISIONS Definitions § 30.10-38 Lightweight—TB/ALL. The term lightweight means the displacement of a vessel in metric tons without cargo, oil...

  8. Novel Architecture for a Long-Life, Lightweight Venus Lander

    Science.gov (United States)

    Bugby, D.; Seghi, S.; Kroliczek, E.; Pauken, M.

    2009-03-01

    This paper describes a novel concept for an extended lifetime, lightweight Venus lander. Historically, to operate in the 480° C, 90 atm, corrosive, mostly CO2 Venus surface environment, previous landers have relied on thick Ti spherical outer shells and thick layers of internal insulation. But even the most resilient of these landers operated for only about 2 hours before succumbing to the environment. The goal on this project is to develop an architecture that extends lander lifetime to 20-25 hours and also reduces mass compared to the Pioneer Venus mission architecture. The idea for reducing mass is to: (a) contain the science instruments within a spherical high strength lightweight polymer matrix composite (PMC) tank; (b) surround the PMC tank with an annular shell of high performance insulation pre-pressurized to a level that (after landing) will exceed the external Venus surface pressure; and (c) surround the insulation with a thin Ti outer shell that contains only a net internal pressure, eliminating buckling overdesign mass. The combination of the PMC inner tank and thin Ti outer shell is lighter than a single thick Ti outer shell. The idea for extending lifetime is to add the following three features: (i) an expendable water supply that is placed within the insulation or is contained in an additional vessel within the PMC tank; (ii) a thin spherical evaporator shell placed within the insulation a short radial distance from the outer shell; and (iii) a thin heat-intercepting liquid cooled shield placed inboard of the evaporator shell. These features lower the temperature of the insulation below what it would have been with the insulation alone, reducing the internal heat leak and lengthening lifetime. The use of phase change materials (PCMs) inside the PMC tank is also analyzed as a lifetime-extending design option. The paper describes: (1) analytical modeling to demonstrate reduced mass and extended life; (2) thermal conductivity testing of high

  9. Lightweight Concrete Produced Using a Two-Stage Casting Process

    Directory of Open Access Journals (Sweden)

    Jin Young Yoon

    2015-03-01

    Full Text Available The type of lightweight aggregate and its volume fraction in a mix determine the density of lightweight concrete. Minimizing the density obviously requires a higher volume fraction, but this usually causes aggregates segregation in a conventional mixing process. This paper proposes a two-stage casting process to produce a lightweight concrete. This process involves placing lightweight aggregates in a frame and then filling in the remaining interstitial voids with cementitious grout. The casting process results in the lowest density of lightweight concrete, which consequently has low compressive strength. The irregularly shaped aggregates compensate for the weak point in terms of strength while the round-shape aggregates provide a strength of 20 MPa. Therefore, the proposed casting process can be applied for manufacturing non-structural elements and structural composites requiring a very low density and a strength of at most 20 MPa.

  10. Lightweight design for servo frame based on lattice material

    Science.gov (United States)

    Jin, Xin; Li, Guoxi; Liu, Encai; Gong, Jingzhong

    2017-06-01

    Lattice material infilling is an important way to achieve lightweight. Focusing on the problems of non-uniform arrangement and the finite element analysis (FEA) of lattice material in the parts, a lightweight design method based on lattice material is proposed with the spacecraft servo frame as the design object. Modal analysis and topology optimization are carried out according to the boundary conditions. The optimized density results are used to guide the design of lattice material parameters and arrangement. The equivalent mechanical properties of lattice material are obtained through the standard specimens experiments. The equivalent material FEA model of the lightweight servo frame is established, and the performance of the lightweight structure is tested by FEA simulation and experiment. The results show that under the impact condition, the lightweight servo frame meets the performance requirements and the simulation method through the equivalent material model is validated.

  11. Super insulating aerogel glazing

    DEFF Research Database (Denmark)

    Schultz, Jørgen Munthe; Jensen, Karsten Ingerslev; Kristiansen, Finn Harken

    2004-01-01

    Monolithic silica aerogel offers the possibility of combining super insulation and high solar energy transmittance, which has been the background for a previous and a current EU project on research and development of monolithic silica aerogel as transparent insulation in windows. Generally, windows...... form the weakest part of the thermal envelope with respect to heat loss coefficient, but on the other hand also play an important role for passive solar energy utilisation. For window orientations other than south, the net energy balance will be close to or below zero. However, the properties...... of aerogel glazing will allow for a positive net energy gain even for north facing vertical windows in a Danish climate during the heating season. This means that high quality daylight can be obtained even with additional energy gain. On behalf of the partners of the two EU projects, results related...

  12. SuperWiseNet - a unique network platform to leverage student entrepreneurship projects

    DEFF Research Database (Denmark)

    Gertsen, Frank; Høgsaa, Asger; Tollestrup, Christian H. T.

    2016-01-01

    The area of interests is the development of a potentially new complementary industry-university component, which has been labelled ‘SuperWiseNet’ for the context of academic entrepreneurial programs. The SuperWiseNet is a network-based platform for interaction between students of entrepreneurship...... Engineering Master’s Program [1] at Aalborg University, Denmark (120 ECTS credits). The paper will describe and elaborate on the functioning of SuperWiseNet including a discussion of advantages for students, faculty, and industry/externals as well as some challenges with the concept....

  13. External Otitis (Swimmer's Ear)

    Science.gov (United States)

    ... to Pneumococcal Vaccine Additional Content Medical News External Otitis (Swimmer's Ear) By Bradley W. Kesser, MD, Associate ... the Outer Ear Ear Blockages Ear Tumors External Otitis (Swimmer's Ear) Malignant External Otitis Perichondritis External otitis ...

  14. Advanced casting technologies for lightweight automotive applications

    Directory of Open Access Journals (Sweden)

    Alan A. Luo

    2010-11-01

    Full Text Available This paper provides an overview of alloy and process developments in aluminum and magnesium castings for lightweight automotive applications. Wear-resistant aluminum alloys, creep-resistant and high strength/ductility magnesium alloys have been developed for automotive applications. On the process front, vacuum-assisted die casting and high vacuum die casting technologies have been developed for high-integrity body and chassis applications. Thin-wall and hollow casting components are being produced by low-pressure die casting processes for structural applications. Overcasting technology is gaining traction and has enabled mixed material designs for automotive sub-systems such as engine cradles and instrument panel beams. Simulation tools developed to predict the interfacial interactions of the dissimilar components and the structural integrity of the overcast systems are being validated in the casting trials.

  15. Performance of a New Lightweight Reciprocating Pump

    Energy Technology Data Exchange (ETDEWEB)

    Whitehead, J C

    2005-06-09

    A new four-chamber piston pump design has been fabricated and tested. The small-scale propellant pump is intended to be powered by gas at elevated temperatures, e.g. in a gas-generator cycle rocket propulsion system. Two key features are combined for the first time: leak-tight liquid-cooled seals, and a high throughput per unit hardware mass. Measured performance curves quantify flows, pressures, leakage, volumetric efficiency, and tank pressure requirements. A pair of 300-gram pumps operating with significant margin could deliver fuel and oxidizer at 5 MPa to a compact lightweight 1000-N engine, while tank pressure remains at 0.35 MPa. Pump weight is well below one percent of thrust, as is typical for launch vehicle engines. Applications include small upper stages, aggressive maneuvers in space, and miniature launch vehicles for Mars ascent.

  16. Lightweight, low-cost solar energy collector

    Science.gov (United States)

    Hochberg, Eric B. (Inventor); Costen, Michael K. (Inventor)

    2006-01-01

    A lightweight solar concentrator of the reflecting parabolic or trough type is realized via a thin reflecting film, an inflatable structural housing and tensioned fibers. The reflector element itself is a thin, flexible, specularly-reflecting sheet or film. The film is maintained in the parabolic trough shape by means of a plurality of identical tensioned fibers arranged to be parallel to the longitudinal axis of the parabola. Fiber ends are terminated in two identical spaced anchorplates, each containing a plurality of holes which lie on the desired parabolic contour. In a preferred embodiment, these fibers are arrayed in pairs with one fiber contacting the front side of the reflecting film and the other contacting the back side of the reflecting film. The reflective surface is thereby slidably captured between arrays of fibers which control the shape and position of the reflective film. Gas pressure in the inflatable housing generates fiber tension to achieve a truer parabolic shape.

  17. Utilization of Bamboo as Lightweight Sandwich Panels

    Directory of Open Access Journals (Sweden)

    Suthon SRIVARO

    2016-05-01

    Full Text Available Lightweight sandwich panels consisting of bamboo faces and oil palm trunk core were manufactured using melamine urea formaldehyde with the resin content of 250 g/m2 (solid basis. The parameters examined were node and density of bamboo faces. Physical (board density, thickness swelling and water absorption and mechanical (modulus of elasticity and modulus of rupture properties of the sandwich board obtained were investigated and compared with other bamboo products and commercial wood based products. Result showed that this panel had better dimensional stability than those of other bamboo products but lower bending strength. Node of bamboo had no significant effect on any board properties examined. Most of board properties were influenced by bamboo face density. Comparing the properties to commercial wood based products, this panel could be used as wall/floor applications.

  18. Development of a lightweight fuel cell vehicle

    Science.gov (United States)

    Hwang, J. J.; Wang, D. Y.; Shih, N. C.

    This paper described the development of a fuel cell system and its integration into the lightweight vehicle known as the Mingdao hydrogen vehicle (MHV). The fuel cell system consists of a 5-kW proton exchange membrane fuel cell (PEMFC), a microcontroller and other supported components like a compressed hydrogen cylinder, blower, solenoid valve, pressure regulator, water pump, heat exchanger and sensors. The fuel cell not only propels the vehicle but also powers the supporting components. The MHV performs satisfactorily over a hundred-kilometer drive thus validating the concept of a fuel cell powered zero-emission vehicle. Measurements further show that the fuel cell system has an efficiency of over 30% at the power consumption for vehicle cruise, which is higher than that of a typical internal combustion engine. Tests to improve performance such as speed enhancement, acceleration and fuel efficiency will be conducted in the future work. Such tests will consist of hybridizing with a battery pack.

  19. Utilization of Bamboo as Lightweight Sandwich Panels

    Directory of Open Access Journals (Sweden)

    Suthon SRIVARO

    2016-05-01

    Full Text Available Lightweight sandwich panels consisting of bamboo faces and oil palm trunk core were manufactured using melamine urea formaldehyde with the resin content of 250 g/m2 (solid basis. The parameters examined were node and density of bamboo faces. Physical (board density, thickness swelling and water absorption and mechanical (modulus of elasticity and modulus of rupture properties of the sandwich board obtained were investigated and compared with other bamboo products and commercial wood based products. Result showed that this panel had better dimensional stability than those of other bamboo products but lower bending strength. Node of bamboo had no significant effect on any board properties examined. Most of board properties were influenced by bamboo face density. Comparing the properties to commercial wood based products, this panel could be used as wall/floor applications.

  20. Lightweight ceramic filter components: Evaluation and application

    Energy Technology Data Exchange (ETDEWEB)

    Eggerstedt, P.M.

    1995-11-01

    Ceramic candle filtration is an attractive technology for particulate removal at high temperatures. The primary objective of this SBIR research program is to increase the performance, durability, and corrosion resistance of lightweight filter candles and filter tubesheet components (Fibrosic{trademark}), fabricated from vacuum formed chopped ceramic fiber (VFCCF), for use in advanced coal utilization applications. Phase 1 results proved that significant gains in material strength and particle retentivity are possible by treatment of VFCCF materials with colloidal ceramic oxides. Phase 2 effort will show how these treated materials tolerate high temperature and vapor-phase alkali species, on a long-term basis. With good durability and corrosion resistance, high temperature capability, and a low installed and replacement cost, these novel materials will help promote commercial acceptance of ceramic candle filter technology, as well as increase the efficiency and reliability of coal utilization processes in general.

  1. Xinjiang Girl World Super Model

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    Leading Chinese model Yue Mei won thetitle of World Super Model at the ’98 WorldSuper Model Competition held in FranceSeptember 6 - 17. Yue, a university studentfrom the Xinjiang Uygur AutonomousRegion, had won the top title at ’98 ChinaSuper Model Competition held in Beijingone month earier.After that, she underwentone month’s professional modeling trainingwith the New Silk Road ModelingManagement Company before setting off forthe world competition. In France, Yueimpressed the judges with her strikingfeatures, and display of oriental elegance and

  2. Lightweight MIPv6 with IPSec Support

    Directory of Open Access Journals (Sweden)

    Antonio J. Jara

    2014-01-01

    Full Text Available Mobility management is a desired feature for the emerging Internet of Things (IoT. Mobility aware solutions increase the connectivity and enhance adaptability to changes of the location and infrastructure. IoT is enabling a new generation of dynamic ecosystems in environments such as smart cities and hospitals. Dynamic ecosystems require ubiquitous access to Internet, seamless handover, flexible roaming policies, and an interoperable mobility protocol with existing Internet infrastructure. These features are challenges for IoT devices, which are usually constrained devices with low memory, processing, communication and energy capabilities. This work presents an analysis of the requirements and desirable features for the mobility support in the IoT, and proposes an efficient solution for constrained environments based on Mobile IPv6 and IPSec. Compatibility with IPv6-existing protocols has been considered a major requirement in order to offer scalable and inter-domain solutions that were not limited to specific application domains in order to enable a new generation of application and services over Internet-enabled dynamic ecosystems, and security support based on IPSec has been also considered, since dynamic ecosystems present several challenges in terms of security and privacy. This work has, on the one hand, analysed suitability of Mobile IPv6 and IPSec for constrained devices, and on the other hand, analysed, designed, developed and evaluated a lightweight version of Mobile IPv6 and IPSec. The proposed solution of lightweight Mobile IPv6 with IPSec is aware of the requirements of the IoT and presents the best solution for dynamic ecosystems in terms of efficiency and security adapted to IoT-devices capabilities. This presents concerns in terms of higher overhead and memory requirements. But, it is proofed and concluded that even when higher memory is required and major overhead is presented, the integration of Mobile IPv6 and IPSec for

  3. Vehicular hydrogen storage using lightweight tanks

    Energy Technology Data Exchange (ETDEWEB)

    Mitlitsky, F; Weisberg, A H; Myers, B

    2000-07-22

    Lightweight hydrogen storage for vehicles is enabled by adopting and adapting aerospace tankage technology. The weight, volume, and cost are already acceptable and improving. Prototype tankage was demonstrated with 11.3% hydrogen by weight, 1.74 million inch (44.3 km) burst performance factor (P{sub b}V/W), and 3.77 kWh/kg specific energy for the tank and hydrogen (LHV). DOE cannot afford full scale aerospace development costs. For example, it costs many tens of $M to develop a rocket motor casing with a safety factor (SF) of 1.25. Large teams of experts are required to design, develop, and test new processes. Car companies are buying existing technology with only modest investments in research and development (R&D). The Lawrence Livermore National Laboratory (LLNL) team is maximizing the leverage from DOE funding by joining with industry to solve technical risks at the component level. LLNL is developing fabrication processes with IMPCO Technologies, Thiokol Propulsion, and Aero Tec Laboratories (ATL). LLNL is creating commercial products that are close to adoption under DOE solicitation. LLNL is breaking ground to achieve greater than 10% hydrogen by weight tankage with safety that exceeds the requirements of NGV2 standards modified for hydrogen. Risk reduction is proceeding along three axes: (1) Commercializable products will be available next year with {approx}90% confidence; (2) R&D progress is pushing the envelope in lightweight tankage for vehicles; and (3) Integration challenges are being met with partners in industry and DOE demo programs. This project is a key part of LLNL's effort to develop high cycle life energy storage systems with >600 Wh/kg specific energy for various applications, including: high altitude long endurance solar rechargeable aircraft, zero emission vehicles, hybrid energy storage/propulsion systems for spacecraft, energy storage for premium power, remote power sources, and peak shaving.

  4. Lightweight males of Podisus nigrispinus (Heteroptera: Pentatomidae neglect lightweight females due low reproductive fitness

    Directory of Open Access Journals (Sweden)

    A. I. A. Pereira

    Full Text Available Abstract Sexual choice by male stink bugs is important because females that experience food shortages lay fewer eggs with lower viability compared with well-fed females. In this study, we investigated whether Podisus nigrispinus (Dallas (Heteroptera: Pentatomidae males fed with a low-quality diet during its nymphal stage show selectivity for sexual partners resulting in high-quality progeny. Lightweight males and females were obtained from nymphs fed weekly with Tenebrio molitor L. (Coleoptera: Tenebrionidae pupae. By contrast, heavyweight males and females were fed three times a week and received an extra nutritional source: cotton leaves, Gossypium hirsutum L. (Malvaceae. Lightweight males preferred to mate with heavy females (77.78 ± 14.69%, whereas heavyweight males did not discriminated between light or heavyweight females. Females mated with lightweight males showed similar levels of reproduction to those mated with heavyweight males. The results provide an indication of the importance of male and female body weight for sexual selection in Asopinae stink bugs.

  5. SuperB Progress Reports Accelerator

    CERN Document Server

    Biagini, Maria Enrica; Boscolo, M; Buonomo, B; Demma, T; Drago, A; Esposito, M; Guiducci, S; Mazzitelli, G; Pellegrino, L; Preger, M A; Raimondi, P; Ricci, R; Rotundo, U; Sanelli, C; Serio, M; Stella, A; Tomassini, S; Zobov, M; Bertsche, K; Brachman, A; Cai, Y; Chao, A; Chesnut, R; Donald, M.H; Field, C; Fisher, A; Kharakh, D; Krasnykh, A; Moffeit, K; Nosochkov, Y; Pivi, M; Seeman, J; Sullivan, M.K; Weathersby, S; Weidemann, A; Weisend, J; Wienands, U; Wittmer, W; Woods, M; Yocky, G; Bogomiagkov, A; Koop, I; Levichev, E; Nikitin, S; Okunev, I; Piminov, P; Sinyatkin, S; Shatilov, D; Vobly, P; Bosi, F; Liuzzo, S; Paoloni, E; Bonis, J; Chehab, R; Le Meur, G; Lepercq, P; Letellier-Cohen, F; Mercier, B; Poirier, F; Prevost, C; Rimbault, C; Touze, F; Variola, A; Bolzon, B; Brunetti, L; Jeremie, A; Baylac, M; Bourrion, O; De Conto, J M; Gomez, Y; Meot, F; Monseu, N; Tourres, D; Vescovi, C; Chanci, A; Napoly, O; Barber, D P; Bettoni, S; Quatraro, D

    2010-01-01

    This report details the present status of the Accelerator design for the SuperB Project. It is one of four separate progress reports that, taken collectively, describe progress made on the SuperB Project since the publication of the SuperB Conceptual Design Report in 2007 and the Proceedings of SuperB Workshop VI in Valencia in 2008.

  6. SuperB Progress Report: Detector

    Energy Technology Data Exchange (ETDEWEB)

    Grauges, E.; /Barcelona U., ECM; Donvito, G.; Spinoso, V.; /INFN, Bari /Bari U.; Manghisoni, M.; Re, V.; Traversi, G.; /INFN, Pavia /Bergamo U., Ingengneria Dept.; Eigen, G.; Fehlker, D.; Helleve, L.; /Bergen U.; Carbone, A.; Di Sipio, R.; Gabrielli, A.; Galli, D.; Giorgi, F.; Marconi, U.; Perazzini, S.; Sbarra, C.; Vagnoni, V.; Valentinetti, S.; Villa, M.; Zoccoli, A.; /INFN, Bologna /Bologna U. /Caltech /Carleton U. /Cincinnati U. /INFN, CNAF /INFN, Ferrara /Ferrara U. /UC, Irvine /Taras Shevchenko U. /Orsay, LAL /LBL, Berkeley /UC, Berkeley /Frascati /INFN, Legnaro /Orsay, IPN /Maryland U. /McGill U. /INFN, Milan /Milan U. /INFN, Naples /Naples U. /Novosibirsk, IYF /INFN, Padua /Padua U. /INFN, Pavia /Pavia U. /INFN, Perugia /Perugia U. /INFN, Perugia /Caltech /INFN, Pisa /Pisa U. /Pisa, Scuola Normale Superiore /PNL, Richland /Queen Mary, U. of London /Rutherford /INFN, Rome /Rome U. /INFN, Rome2 /Rome U.,Tor Vergata /INFN, Rome3 /Rome III U. /SLAC /Tel Aviv U. /INFN, Turin /Turin U. /INFN, Padua /Trento U. /INFN, Trieste /Trieste U. /TRIUMF /British Columbia U. /Montreal U. /Victoria U.

    2012-02-14

    This report describes the present status of the detector design for SuperB. It is one of four separate progress reports that, taken collectively, describe progress made on the SuperB Project since the publication of the SuperB Conceptual Design Report in 2007 and the Proceedings of SuperB Workshop VI in Valencia in 2008.

  7. Vehicle Lightweighting: Mass Reduction Spectrum Analysis and Process Cost Modeling

    Energy Technology Data Exchange (ETDEWEB)

    Mascarin, Anthony [IBIS Associates, Inc., Waltham, MA (United States); Hannibal, Ted [IBIS Associates, Inc., Waltham, MA (United States); Raghunathan, Anand [Energetics Inc., Columbia, MD (United States); Ivanic, Ziga [Energetics Inc., Columbia, MD (United States); Clark, Michael [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-03-01

    The U.S. Department of Energy’s Vehicle Technologies Office, Materials area commissioned a study to model and assess manufacturing economics of alternative design and production strategies for a series of lightweight vehicle concepts. In the first two phases of this effort examined combinations of strategies aimed at achieving strategic targets of 40% and a 45% mass reduction relative to a standard North American midsize passenger sedan at an effective cost of $3.42 per pound (lb) saved. These results have been reported in the Idaho National Laboratory report INL/EXT-14-33863 entitled Vehicle Lightweighting: 40% and 45% Weight Savings Analysis: Technical Cost Modeling for Vehicle Lightweighting published in March 2015. The data for these strategies were drawn from many sources, including Lotus Engineering Limited and FEV, Inc. lightweighting studies, U.S. Department of Energy-funded Vehma International of America, Inc./Ford Motor Company Multi-Material Lightweight Prototype Vehicle Demonstration Project, the Aluminum Association Transportation Group, many United States Council for Automotive Research’s/United States Automotive Materials Partnership LLC lightweight materials programs, and IBIS Associates, Inc.’s decades of experience in automotive lightweighting and materials substitution analyses.

  8. Security Isolation Strategy Mechanism for Lightweight Virtualization Environment

    Directory of Open Access Journals (Sweden)

    Liu Qian

    2017-01-01

    Full Text Available For cloud service providers, lightweight virtualization is a more economical way of virtualization. While the user is worried about the safety of applications and data of the container, due to the container sharing the underlying interface and the kernel, therefore the security and trusted degree of lightweight virtualization container isolation mechanism is critical for the promotion of lightweight virtualization service. Because the user cannot directly participate in the process of the construction and management of container isolation mechanism, it is difficult for them to establish confidence in the security and trusted degree of container isolation mechanism. Based on the research and analysis of system credible and virtualization isolation mechanism, this paper puts forward a set of lightweight virtualization security isolation strategy mechanism, divides lightweight virtualization container storage address space into several parts, puts forward the definition of lightweight virtualization security isolation, gives the formal description and proof of container security isolation strategy, and combines with related technology to verify the feasibility of lightweight virtualization security isolation strategy mechanism. The mechanism has important guiding significance for cloud services providers to deploy container security isolation.

  9. Simulation of flanking transmission in super-light structures for airborne and impact sound

    DEFF Research Database (Denmark)

    Christensen, Jacob Ellehauge; Hertz, Kristian Dahl; Brunskog, Jonas

    2012-01-01

    Super-light structures are an invention based on combining lightweight concrete with normal concrete for better structural performance and lighter structures. The overall principle is based on load carrying arches of a normal concrete stabilised and protected from fire by a light-aggregate concrete....... In the flanking transmission analysis the influence of a large array of different flanking walls, structural connection details, room size and floor constructions, all typical or desirable for common multi-storey residential constructions, have been investigated. The results form a basis for guidelines on how...

  10. An atmosphere around the super-Earth 55 Cancri e

    Science.gov (United States)

    Tsiaras, Angelos; Rocchetto, Marco; Waldmann, Ingo; Venot, Olivia; Varley, Rayan; Morello, Giuseppe; Damiano, Mario; Tinetti, Giovanna; Barton, Emma; Yurchenko, Sergey; Tennyson, Jonathan; ExoLights, ExoMol

    2016-10-01

    One of the most successful instruments for observing exoplanetary atmospheres is the Wide Field Camera 3 (WFC3) onboard the Hubble Space Telescope (HST). In particular, the use of the spatial scanning technique has given us the opportunity for even more efficient observations of the brightest targets, achieving the necessary precision of 10 – 100 ppm. With such data and new advanced reduction and statistical techniques, we were able to detect modulations in the spectrum of the hot super-Earth 55 Cancri e, which suggest the existence of a light-weight atmosphere around this planet. Given the brightness of 55 Cancri, the observers adopted a very long scanning length and a very high scanning speed. We took these effects into account, as they can introduce systematics when coupled with the geometrical distortions of the instrument. Our fully Bayesian spectral retrieval code, T-REx, has identified HCN to be the most likely molecular candidate able to explain the features at 1.42 and 1.54 μm. While additional spectroscopic observations in a broader wavelength range in the infrared will be needed to confirm the HCN detection, we used a chemical model, developed with combustion specialists, to explain its pressence. This model indicates that relatively high mixing ratios of HCN may be caused by a high C/O ratio, suggesting this super-Earth is a carbon-rich environment even more exotic than previously thought.

  11. What's So Super about Superfoods?

    Science.gov (United States)

    ... with meals. The Skinny on Common Super Foods Salmon is a fatty fish that’s low in saturated ... soy nuts are high in polyunsaturated fat, fiber, vitamins and minerals but low in saturated fat. They ...

  12. Super Ministries,Better Administration

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ Chinese lawmakers on March 15th endorsed a State Counci l proposal for institutional overhaul of the tentral government,which involves the establishment of"super ministries"concerning energy,transport,industry and environmental protection.

  13. Effect of lightweight aggregate intrinsic Strength on lightweight concrete compressive strength and modulus of elasticity

    Directory of Open Access Journals (Sweden)

    Videla, C.

    2002-03-01

    Full Text Available The study of Structural Lightweight Concrete (SLC, which is a material generally composed of cement, water and lightweight aggregate, has been mainly focused on developing particular cases. Then, the main objective of this research was to generalise the knowledge of this type of material. Particularly, the effect of replacing conventional coarse aggregate by lightweight aggregate on mechanical properties of concrete was studied. SLC may be conceived as a two -phase material. The first phase, composed of cement, water and siliceous natural sand, is called the "resistant phase", and contributes to the structural strength. The second phase is the lightweight phase, comprised of coarse lightweight aggregate, and it is meant to decrease the concrete density. In this way it would be possible to describe the mechanical behaviour of concrete, based on lightweight aggregate and the cement mortar parameters. The obtained results allow for the proposition of relationships between mechanical properties of SLC (such as compressive strength and modulus of elasticity and the constituent materials properties and amount. At the same time, an easily measured index representing the structural capability of lightweight aggregate is also proposed, this index allows to estimate the potential mechanical properties of concrete which could be obtained by using a particular aggregate.

    El estudio del Hormigón Ligero Estructural (HLE, material compuesto generalmente por cemento, agua y árido ligero, ha estado enfocado principalmente al desarrollo de casos particulares. Por lo anterior, el objetivo principal de esta investigación fue generalizar el conocimiento sobre este material. En particular, la meta de este trabajo fue estudiar el efecto que tiene el reemplazo de árido convencional por un árido ligero, en las propiedades mecánicas del hormigón. El modelo aplicado conceptualiza al HLE como un material de dos fases, una denominada "soportante", constituida

  14. Integrated Control with Structural Feedback to Enable Lightweight Aircraft

    Science.gov (United States)

    Taylor, Brian R.

    2011-01-01

    This presentation for the Fundamental Aeronautics Program Technical Conference covers the benefits of active structural control, related research areas, and focuses on the use of optimal control allocation for the prevention of critical loads. Active control of lightweight structures has the potential to reduce aircraft weight and fuel burn. Sensor, control law, materials, control effector, and system level research will be necessary to enable active control of lightweight structures. Optimal control allocation with structural feedback has been shown in simulation to be feasible in preventing critical loads and is one example of a control law to enable future lightweight aircraft.

  15. Lightweight Phase-Change Material For Solar Power

    Science.gov (United States)

    Stark, Philip

    1993-01-01

    Lightweight panels containing phase-change materials developed for use as heat-storage elements of compact, lightweight, advanced solar dynamic power system. During high insolation, heat stored in panels via latent heat of fusion of phase-change material; during low insolation, heat withdrawn from panels. Storage elements consist mainly of porous carbon-fiber structures imbued with germanium. Developed for use aboard space station in orbit around Earth, also adapted to lightweight, compact, portable solar-power systems for use on Earth.

  16. What are super-enhancers?

    Science.gov (United States)

    Pott, Sebastian; Lieb, Jason D

    2015-01-01

    The term 'super-enhancer' has been used to describe groups of putative enhancers in close genomic proximity with unusually high levels of Mediator binding, as measured by chromatin immunoprecipitation and sequencing (ChIP-seq). Here we review the identification and composition of super-enhancers, describe links between super-enhancers, gene regulation and disease, and discuss the functional significance of enhancer clustering. We also provide our perspective regarding the proposition that super-enhancers are a regulatory entity conceptually distinct from what was known before the introduction of the term. Our opinion is that there is not yet strong evidence that super-enhancers are a novel paradigm in gene regulation and that use of the term in this context is not currently justified. However, the term likely identifies strong enhancers that exhibit behaviors consistent with previous models and concepts of transcriptional regulation. In this respect, the super-enhancer definition is useful in identifying regulatory elements likely to control genes important for cell type specification.

  17. Holography based super resolution

    Science.gov (United States)

    Hussain, Anwar; Mudassar, Asloob A.

    2012-05-01

    This paper describes the simulation of a simple technique of superresolution based on holographic imaging in spectral domain. The input beam assembly containing 25 optical fibers with different orientations and positions is placed to illuminate the object in the 4f optical system. The position and orientation of each fiber is calculated with respect to the central fiber in the array. The positions and orientations of the fibers are related to the shift of object spectrum at aperture plane. During the imaging process each fiber is operated once in the whole procedure to illuminate the input object transparency which gives shift to the object spectrum in the spectral domain. This shift of the spectrum is equal to the integral multiple of the pass band aperture width. During the operation of single fiber (ON-state) all other fibers are in OFF-state at that time. The hologram recorded by each fiber at the CCD plane is stored in computer memory. At the end of illumination process total 25 holograms are recorded by the whole fiber array and by applying some post processing and specific algorithm single super resolved image is obtained. The superresolved image is five times better than the band-limited image. The work is demonstrated using computer simulation only.

  18. Design and preparation of film for microsphere based optical super-resolution imaging

    Science.gov (United States)

    Pang, Hui; Du, Chunlei; Qiu, Qi; Yin, Shaoyun; Zhang, Man; Deng, Qiling

    2014-08-01

    In this paper, a novel thin film was proposed for optical super-resolution imaging, which contains a layer of closely-arranged barium titanate glass microsphere with diameter about 30-100μm embedded in a transparent polydimethylsiloxane soft mold. Then the imaging mechanism was analyzed by the finite-difference time-domain (FDTD) simulation and spectrum analysis method. Finally, the thin film was prepared and used to image the sample with sub-wavelength feature to confirm the capability of super-resolution imaging. The experimental result shows that an irresolvable Blu-ray DVD disk with feature size of 300nm can be resolved by placing a thin-film on its surface and then look through it with a conventional microscope. The thin film presented here is flexible, lightweight, easy to carry and can be used in the nanophotonics, nanoplasmonics, and biomedical imaging areas.

  19. Lightweight, Self-Deploying Foam Antenna Structures

    Science.gov (United States)

    Sokolowski, Witold; Levin, Steven; Rand, Peter

    2004-01-01

    Lightweight, deployable antennas for a variety of outer-space and terrestrial applications would be designed and fabricated according to the concept of cold hibernated elastic memory (CHEM) structures, according to a proposal. Mechanically deployable antennas now in use are heavy, complex, and unreliable, and they utilize packaging volume inefficiently. The proposed CHEM antenna structures would be simple and would deploy themselves without need for any mechanisms and, therefore, would be more reliable. The proposed CHEM antenna structures would also weigh less, could be packaged in smaller volumes, and would cost less, relative to mechanically deployable antennas. The CHEM concept was described in two prior NASA Tech Briefs articles: "Cold Hibernated Elastic Memory (CHEM) Expandable Structures" (NPO-20394), Vol. 23, No. 2 (February 1999), page 56; and "Solar Heating for Deployment of Foam Structures" (NPO-20961), Vol. 25, No. 10 (October 2001), page 36. To recapitulate from the cited prior articles: The CHEM concept is one of utilizing opencell foams of shape-memory polymers (SMPs) to make lightweight, reliable, simple, and inexpensive structures that can be alternately (1) compressed and stowed compactly or (2) expanded, then rigidified for use. A CHEM structure is fabricated at full size from a block of SMP foam in its glassy state [at a temperature below the glass-transition temperature (Tg) of the SMP]. The structure is heated to the rubbery state of the SMP (that is, to a temperature above Tg) and compacted to a small volume. After compaction, the structure is cooled to the glassy state of the SMP. The compacting force can then be released and the structure remains compact as long as the temperature is kept below Tg. Upon subsequent heating of the structure above Tg, the simultaneous elastic recovery of the foam and its shape-memory effect cause the structure to expand to its original size and shape. Once thus deployed, the structure can be rigidified by

  20. Ultra-Lightweight Large Aperture Support Structures Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Ultra-lightweight membranes may prove to be very attractive for large aperture systems, but their value will be fully realized only if they are mated with equally...

  1. Lightweight Metal RubberTM Sensors and Interconnects Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of the proposed program is to develop lightweight and highly elastic electrically conducting interconnects and strain sensor arrays for next generation...

  2. study of the strength characteristics of protein-based lightweight ...

    African Journals Online (AJOL)

    user

    Compressive strength test was carried out on the protein-based lightweight foamed concrete produced ... 150 mm were produced using ordinary Portland cement (OPC), fine aggregate, ..... values obtained for the loss on ignition (LOI) and SO3.

  3. Low Cost, Lightweight, Multifunctional Structural Shielding Materials Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR involves the development of a lightweight innovative material for use as structure and radiation shielding in one. APS has assembled a uniquely qualified...

  4. Lightweight IMM Multi-Junction Photovoltaic Flexible Blanket Assembly Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Deployable Space Systems (DSS) and EMCORE as a key subcontractor will focus the proposed SBIR program on the creation and optimization of a lightweight ~33%...

  5. Lightweight InP Solar Cells for Space Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The innovation in this Phase II SBIR is the development of a technology which will enable the manufacture of a lightweight, low cost, high radiation resistance InP...

  6. Next Generation MK III Lightweight HUT/Hatch Assembly Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A prototype Next Generation MK III Lightweight HUT/Hatch Assembly will be fabricated and delivered during Phase II. Maximum weight reduction for the Hard Upper...

  7. Next Generation MK III Lightweight HUT/Hatch Assembly Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Next Generation MK III Lightweight HUT/Hatch Assembly will maximize the Hard Upper Torso - Hatch assembly weight reduction through the combination of innovative...

  8. Lightweight landscape enhancing design through minimal mass structures

    CERN Document Server

    Spinelli, Luigi; Monticelli, Carol; Pedrali, Paolo

    2016-01-01

    This book explains how lightweight materials and structures can be deployed in buildings to meet high environmental and aesthetic standards and emphasizes how the concept of lightness in building technology and design dovetails with the desire to enhance landscape. The first part of the book, on lightweight construction, aims to foster the use of membranes within the specific climatic context and in particular considers how lightweight materials and innovative technologies can enrich the quality of temporary spaces. The second part focuses exclusively on landscape, presenting novel approaches in the search for visual lightness and the quest to improve urban spaces. Particular attention is paid to the Italian experience, where the traditional appreciation of brick and stone has limited the scope for use of lightweight structures and membrane materials, often relegating them to a secondary or inappropriate role. The reader will come to appreciate how this attitude demeans a very advanced productive sector and n...

  9. Lightweight InP Solar Cells for Space Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The innovation in this Phase I SBIR is the development of a technology which will enable the manufacture of a lightweight, low cost, InP based compound semiconductor...

  10. Study on Performance and Processability of Sirofil Lightweight Worsted Fabric

    Institute of Scientific and Technical Information of China (English)

    李明菊; 范德炘; 葛惠萍; 侯祖龄

    2001-01-01

    The lightweight worsted fabric made of Sirofil yarn was developed and its textile performance was studied. By means of conventional testing, KES and FAST, it is concluded that with the coordination of proper fabric design and processing technique, the performance of this innovative fabric is superior to that of the conventional lightweight fabric Furthermore, it is predicted from the relevant parameters that its processability in the following suit manufacture is very desirable.

  11. Lightweight Aggregate Concrete Beams. Load-bearing Capacity

    DEFF Research Database (Denmark)

    Larsen, Henning; Goltermann, Per; Ingholt, N.U.

    1997-01-01

    This paper deals with the load-bearing capacity of reinforced beams made of lightweight aggregate concrete with open structure and documents formulas for the moment capacity as well as the shear force capacity.......This paper deals with the load-bearing capacity of reinforced beams made of lightweight aggregate concrete with open structure and documents formulas for the moment capacity as well as the shear force capacity....

  12. Lightweight Aggregate Concrete Components. Load-bearing Capacity

    DEFF Research Database (Denmark)

    Larsen, Henning; Ingholt, N.U.; Goltermann, Per

    1996-01-01

    The project presented here deals with the load-bearing capacity of reinforced beams made of lightweight aggregate concrete with open structure and documents expressions for the moment capacity as well as the shear force capacity......The project presented here deals with the load-bearing capacity of reinforced beams made of lightweight aggregate concrete with open structure and documents expressions for the moment capacity as well as the shear force capacity...

  13. Lightweight Absorption and Barrier Systems Comprising N-Layer Microperforates

    OpenAIRE

    Kim, Nicholas N; Bolton, J. Stuart

    2017-01-01

    Since the concept of microperforated panels (MPPs) was introduced by Maa, there have been continuing efforts to apply MPPs, primarily as fiber-free sound absorbing materials, typically wall-mounted. The objective of the present work was to demonstrate that multi-layer MPPs can also be effective functional absorbers and lightweight barrier systems. The acoustical properties of lightweight MPPs depend on hole diameter, thickness, porosity, mass per unit area, and air cavity depth. In the case o...

  14. UTILIZATION OF LIGHTWEIGHT MATERIALS MADE FROM COAL GASIFICATION SLAGS

    Energy Technology Data Exchange (ETDEWEB)

    Vas Choudhry; Stephen Kwan; Steven R. Hadley

    2001-07-01

    The objective of the project entitled ''Utilization of Lightweight Materials Made from Coal Gasification Slags'' was to demonstrate the technical and economic viability of manufacturing low-unit-weight products from coal gasification slags which can be used as substitutes for conventional lightweight and ultra-lightweight aggregates. In Phase I, the technology developed by Praxis to produce lightweight aggregates from slag (termed SLA) was applied to produce a large batch (10 tons) of expanded slag using pilot direct-fired rotary kilns and a fluidized bed calciner. The expanded products were characterized using basic characterization and application-oriented tests. Phase II involved the demonstration and evaluation of the use of expanded slag aggregates to produce a number of end-use applications including lightweight roof tiles, lightweight precast products (e.g., masonry blocks), structural concrete, insulating concrete, loose fill insulation, and as a substitute for expanded perlite and vermiculite in horticultural applications. Prototypes of these end-use applications were made and tested with the assistance of commercial manufacturers. Finally, the economics of expanded slag production was determined and compared with the alternative of slag disposal. Production of value-added products from SLA has a significant potential to enhance the overall gasification process economics, especially when the avoided costs of disposal are considered.

  15. Advanced steel body concepts for automotive lightweight design

    Energy Technology Data Exchange (ETDEWEB)

    Herrmann, H.G. [DaimlerChrysler AG, Stuttgart (Germany). Research Body and Powertrain

    2005-07-01

    Lightweight design is a must for future vehicle concepts due to the self-commitment on the reduction of fleet consumption. Body concepts for mid- and high-volume vehicles demand smart lightweight solutions without increasing costs and without sacrificing the high level of safety (e.g. future passive safety standards). Furthermore, all lightweight activities have to comply with requirements in terms of reliability (no additional efforts for maintenance), NVH (no additional weight for e.g. damping) and future stricter recycling quotas. Successful lightweight design solutions are determined by the best relation between weight-saving and additional costs as a function of the annual production volume. Using advanced high-strength steels (TWIP-steels) seems to be a very promising approach for cost-optimized lightweight design of body structures. In addition, by applying bionic optimization, the weight of body-structures can be significantly reduced. As a consequence, only a holistic approach for lightweight design combining the three areas materials, design and manufacturing is needed in order to use the full potential of cost-optimized weight-reduction. (orig.)

  16. Lightweight, highly compressible, noncrystalline cellulose capsules.

    Science.gov (United States)

    Carrick, Christopher; Lindström, Stefan B; Larsson, Per Tomas; Wågberg, Lars

    2014-07-08

    We demonstrate how to prepare extraordinarily deformable, gas-filled, spherical capsules from nonmodified cellulose. These capsules have a low nominal density, ranging from 7.6 to 14.2 kg/m(3), and can be deformed elastically to 70% deformation at 50% relative humidity. No compressive strain-at-break could be detected for these dry cellulose capsules, since they did not rupture even when compressed into a disk with pockets of highly compressed air. A quantitative constitutive model for the large deformation compression of these capsules is derived, including their high-frequency mechanical response and their low-frequency force relaxation, where the latter is governed by the gas barrier properties of the dry capsule. Mechanical testing corroborated these models with good accuracy. Force relaxation measurements at a constant compression rendered an estimate for the gas permeability of air through the capsule wall, calculated to 0.4 mL μm/m(2) days kPa at 50% relative humidity. These properties taken together open up a large application area for the capsules, and they could most likely be used for applications in compressible, lightweight materials and also constitute excellent model materials for adsorption and adhesion studies.

  17. Abstracting audit data for lightweight intrusion detection

    KAUST Repository

    Wang, Wei

    2010-01-01

    High speed of processing massive audit data is crucial for an anomaly Intrusion Detection System (IDS) to achieve real-time performance during the detection. Abstracting audit data is a potential solution to improve the efficiency of data processing. In this work, we propose two strategies of data abstraction in order to build a lightweight detection model. The first strategy is exemplar extraction and the second is attribute abstraction. Two clustering algorithms, Affinity Propagation (AP) as well as traditional k-means, are employed to extract the exemplars, and Principal Component Analysis (PCA) is employed to abstract important attributes (a.k.a. features) from the audit data. Real HTTP traffic data collected in our institute as well as KDD 1999 data are used to validate the two strategies of data abstraction. The extensive test results show that the process of exemplar extraction significantly improves the detection efficiency and has a better detection performance than PCA in data abstraction. © 2010 Springer-Verlag.

  18. Lightweight Thermoformed Structural Components and Optics

    Science.gov (United States)

    Zeiders, Glenn W.; Bradford, Larry J.

    2004-01-01

    A technique that involves the use of thermoformed plastics has been developed to enable the design and fabrication of ultra-lightweight structural components and mirrors for use in outer space. The technique could also be used to produce items for special terrestrial uses in which minimization of weight is a primary design consideration. Although the inherent strengths of thermoplastics are clearly inferior to those of metals and composite materials, thermoplastics offer a distinct advantage in that they can be shaped, at elevated temperatures, to replicate surfaces (e.g., prescribed mirror surfaces) precisely. Furthermore, multiple elements can be bonded into structures of homogeneous design that display minimal thermal deformation aside from simple expansion. The design aspect of the present technique is based on the principle that the deflection of a plate that has internal structure depends far more on the overall thickness than on the internal details; thus, a very stiff, light structure can be made from thin plastic that is heatformed to produce a sufficiently high moment of inertia. General examples of such structures include I beams and eggcrates.

  19. Chlorinated drinking water for lightweight laying hens

    Directory of Open Access Journals (Sweden)

    A.F. Schneider

    Full Text Available ABSTRACT The study aimed to evaluate the effect of different levels of chlorine in drinking water of laying hens on zootechnical performance, eggs shell quality, hemogasometry levels and calcium content in tibia. 144 Hy-Line laying hens, 61 weeks old, were used distributed in 24 metabolism cages. They were subjected to water diets, for a period of 28 days, using sodium hypochlorite as a chlorine source in order to obtain the following concentrations: 5ppm (control, 20ppm, 50ppm, and 100ppm. Their performance was evaluated through water consumption, feed intake, egg production and weight, egg mass, feed conversion. Shell quality was measured by specific gravity. At the end of the experiment, arterial blood was collected for blood gas level assessment and a poultry of each replicate was sacrificed to obtain tibia and calcium content measurement. There was a water consumption reduction from 20ppm of chlorine and feed intake reduction in poultry receiving water with 100ppm of chlorine. The regression analysis showed that the higher the level of chlorine in water, the higher the reduction in consumption. There were no differences in egg production and weight, egg mass, feed conversion, specific gravity, tibia calcium content, and hemogasometry levels (hydrogenionic potential, carbon dioxide partial pressure, oxygen partial pressure, sodium, potassium, chloride, bicarbonate, carbon dioxide total concentration, anion gap and oxygen saturation. The use of levels above 5ppm of chlorine is not recommended in the water of lightweight laying hens.

  20. Parallel Array Classes and Lightweight Sharing Mechanisms

    Directory of Open Access Journals (Sweden)

    Steve W. Otto

    1993-01-01

    Full Text Available We discuss a set of parallel array classes, MetaMP, for distributed-memory architectures. The classes are implemented in C++ and interface to the PVM or Intel NX message-passing systems. An array class implements a partitioned array as a set of objects distributed across the nodes – a "collective" object. Object methods hide the low-level message-passing and implement meaningful array operations. These include transparent guard strips (or sharing regions that support finite-difference stencils, reductions and multibroadcasts for support of pivoting and row operations, and interpolation/contraction operations for support of multigrid algorithms. The concept of guard strips is generalized to an object implementation of lightweight sharing mechanisms for finite element method (FEM and particle-in-cell (PIC algorithms. The sharing is accomplished through the mechanism of weak memory coherence and can be efficiently implemented. The price of the efficient implementation is memory usage and the need to explicitly specify the coherence operations. An intriguing feature of this programming model is that it maps well to both distributed-memory and shared-memory architectures.

  1. Lightweight Solar Power for Small Satellites

    Science.gov (United States)

    Nabors, Sammy A.

    2015-01-01

    The innovation targets small satellites or CubeSats for which conventional deployable arrays are not feasible due to their size, weight and complexity. This novel solar cell array includes a thin and flexible photovoltaic cell applied to an inflatable structure to create a high surface area array for collecting solar energy in a lightweight, simple and deployable structure. The inflatable array, with its high functional surface area, eliminates the need and the mechanisms required to point the system toward the sun. The power density achievable in these small arrays is similar to that of conventional high-power deployable/pointable arrays used on large satellites or space vehicles. Although inflatable solar arrays have been previously considered by others, the arrays involved the use of traditional rigid solar cells. Researchers are currently working with thin film photovoltaics from various suppliers so that the NASA innovation is not limited to any particular solar cell technology. NASA has built prototypes and tested functionality before and after inflation. As shown in the current-voltage currents below, deployment does not damage the cell performance.

  2. Novel hyperspectral imager for lightweight UAVs

    Science.gov (United States)

    Saari, Heikki; Aallos, Ville-Veikko; Holmlund, Christer; Mäkynen, Jussi; Delauré, Bavo; Nackaerts, Kris; Michiels, Bart

    2010-04-01

    VTT Technical Research Centre of Finland has developed a new miniaturized staring hyperspectral imager with a weight of 350 g making the system compatible with lightweight UAS platforms. The instrument is able to record 2D spatial images at the selected wavelength bands simultaneously. The concept of the hyperspectral imager has been published in the SPIE Proc. 74741. The operational wavelength range of the imager can be tuned in the range 400 - 1100 nm and spectral resolution is in the range 5 - 10 nm @ FWHM. Presently the spatial resolution is 480 × 750 pixels but it can be increased simply by changing the image sensor. The field of view of the system is 20 × 30 degrees and ground pixel size at 100 m flying altitude is around 7.5 cm. The system contains batteries, image acquisition control system and memory for the image data. It can operate autonomously recording hyperspectral data cubes continuously or controlled by the autopilot system of the UAS. The new hyperspectral imager prototype was first tried in co-operation with the Flemish Institute for Technological Research (VITO) on their UAS helicopter. The instrument was configured for the spectral range 500 - 900 nm selected for the vegetation and natural water monitoring applications. The design of the UAS hyperspectral imager and its characterization results together with the analysis of the spectral data from first test flights will be presented.

  3. Lightweight autonomous chemical identification system (LACIS)

    Science.gov (United States)

    Lozos, George; Lin, Hai; Burch, Timothy

    2012-06-01

    Smiths Detection and Intelligent Optical Systems have developed prototypes for the Lightweight Autonomous Chemical Identification System (LACIS) for the US Department of Homeland Security. LACIS is to be a handheld detection system for Chemical Warfare Agents (CWAs) and Toxic Industrial Chemicals (TICs). LACIS is designed to have a low limit of detection and rapid response time for use by emergency responders and could allow determination of areas having dangerous concentration levels and if protective garments will be required. Procedures for protection of responders from hazardous materials incidents require the use of protective equipment until such time as the hazard can be assessed. Such accurate analysis can accelerate operations and increase effectiveness. LACIS is to be an improved point detector employing novel CBRNE detection modalities that includes a militaryproven ruggedized ion mobility spectrometer (IMS) with an array of electro-resistive sensors to extend the range of chemical threats detected in a single device. It uses a novel sensor data fusion and threat classification architecture to interpret the independent sensor responses and provide robust detection at low levels in complex backgrounds with minimal false alarms. The performance of LACIS prototypes have been characterized in independent third party laboratory tests at the Battelle Memorial Institute (BMI, Columbus, OH) and indoor and outdoor field tests at the Nevada National Security Site (NNSS). LACIS prototypes will be entering operational assessment by key government emergency response groups to determine its capabilities versus requirements.

  4. Testnodes: a Lightweight Node-Testing Infrastructure

    Science.gov (United States)

    Fay, R.; Bland, J.

    2014-06-01

    A key aspect of ensuring optimum cluster reliability and productivity lies in keeping worker nodes in a healthy state. Testnodes is a lightweight node testing solution developed at Liverpool. While Nagios has been used locally for general monitoring of hosts and services, Testnodes is optimised to answer one question: is there any reason this node should not be accepting jobs? This tight focus enables Testnodes to inspect nodes frequently with minimal impact and provide a comprehensive and easily extended check with each inspection. On the server side, Testnodes, implemented in python, interoperates with the Torque batch server to control the nodes production status. Testnodes remotely and in parallel executes client-side test scripts and processes the return codes and output, adjusting the node's online/offline status accordingly to preserve the integrity of the overall batch system. Testnodes reports via log, email and Nagios, allowing a quick overview of node status to be reviewed and specific node issues to be identified and resolved quickly. This presentation will cover testnodes design and implementation, together with the results of its use in production at Liverpool, and future development plans.

  5. Electrically tuned super-capacitors

    CERN Document Server

    Chowdhury, Tazima S

    2015-01-01

    Fast charging and discharging of large amounts of electrical energy make super-capacitors ideal for short-term energy storage [1-5]. In its simplest form, the super-capacitor is an electrolytic capacitor made of an anode and a cathode immersed in an electrolyte. As for an ordinary capacitor, minimizing the charge separation distance and increasing the electrode area increase capacitance. In super-capacitors, charge separation is of nano-meter scale at each of the electrode interface (the Helmholtz double layer). Making the electrodes porous increases their effective surface area [6-8]. A separating layer between the anode and the cathode electrodes is used to minimize unintentional electrical discharge (Figure 1). Here we show how to increase the capacitance of super-capacitors by more than 45 percent when modifying the otherwise passive separator layer into an active diode-like structure. Active control of super-capacitors may increase their efficiency during charge and discharge cycles. Controlling ion flow...

  6. Quantization of super Teichmueller spaces

    Energy Technology Data Exchange (ETDEWEB)

    Aghaei, Nezhla

    2016-08-15

    The quantization of the Teichmueller spaces of Riemann surfaces has found important applications to conformal field theory and N=2 supersymmetric gauge theories. We construct a quantization of the Teichmueller spaces of super Riemann surfaces, using coordinates associated to the ideal triangulations of super Riemann surfaces. A new feature is the non-trivial dependence on the choice of a spin structure which can be encoded combinatorially in a certain refinement of the ideal triangulation. We construct a projective unitary representation of the groupoid of changes of refined ideal triangulations. Therefore, we demonstrate that the dependence of the resulting quantum theory on the choice of a triangulation is inessential. In the quantum Teichmueller theory, it was observed that the key object defining the Teichmueller theory has a close relation to the representation theory of the Borel half of U{sub q}(sl(2)). In our research we observed that the role of U{sub q}(sl(2)) is taken by quantum superalgebra U{sub q}(osp(1 vertical stroke 2)). A Borel half of U{sub q}(osp(1 vertical stroke 2)) is the super quantum plane. The canonical element of the Heisenberg double of the quantum super plane is evaluated in certain infinite dimensional representations on L{sup 2}(R) x C{sup 1} {sup vertical} {sup stroke} {sup 1} and compared to the flip operator from the Teichmueller theory of super Riemann surfaces.

  7. Super-Virasoro anomaly, super-Weyl anomaly and the super-Liouville action for 2D supergravity

    CERN Document Server

    Fujiwara, T; Suzuki, T; Fujiwara, Takanori; Igarashi, Hiroshi; Suzuki, Tadao

    1996-01-01

    The relation between super-Virasoro anomaly and super-Weyl anomaly in N=1 NSR superstring coupled with 2D supergravity is investigated from canonical theoretical view point. The WZW action canceling the super-Virasoro anomaly is explicitly constructed. It is super-Weyl invariant but nonlocal functional of 2D supergravity. The nonlocality can be remedied by the super-Liouvlle action, which in turn recovers the super-Weyl anomaly. The final gravitational effective action turns out to be local but noncovariant super-Liouville action, describing the dynamical behavior of the super-Liouville fields. The BRST invariance of this approach is examined in the superconformal gauge and in the light-cone gauge.

  8. The Super-Kamiokande Experiment

    CERN Document Server

    Walter, C W

    2008-01-01

    Super-Kamiokande is a 50 kiloton water Cherenkov detector located at the Kamioka Observatory of the Institute for Cosmic Ray Research, University of Tokyo. It was designed to study neutrino oscillations and carry out searches for the decay of the nucleon. The Super-Kamiokande experiment began in 1996 and in the ensuing decade of running has produced extremely important results in the fields of atmospheric and solar neutrino oscillations, along with setting stringent limits on the decay of the nucleon and the existence of dark matter and astrophysical sources of neutrinos. Perhaps most crucially, Super-Kamiokande for the first time definitively showed that neutrinos have mass and undergo flavor oscillations. This chapter will summarize the published scientific output of the experiment with a particular emphasis on the atmospheric neutrino results.

  9. Next Generation Lightweight Mirror Modeling Software

    Science.gov (United States)

    Arnold, William R., Sr.; Fitzgerald, Mathew; Rosa, Rubin Jaca; Stahl, H. Philip

    2013-01-01

    The advances in manufacturing techniques for lightweight mirrors, such as EXELSIS deep core low temperature fusion, Corning's continued improvements in the Frit bonding process and the ability to cast large complex designs, combined with water-jet and conventional diamond machining of glasses and ceramics has created the need for more efficient means of generating finite element models of these structures. Traditional methods of assembling 400,000 + element models can take weeks of effort, severely limiting the range of possible optimization variables. This paper will introduce model generation software developed under NASA sponsorship for the design of both terrestrial and space based mirrors. The software deals with any current mirror manufacturing technique, single substrates, multiple arrays of substrates, as well as the ability to merge submodels into a single large model. The modeler generates both mirror and suspension system elements, suspensions can be created either for each individual petal or the whole mirror. A typical model generation of 250,000 nodes and 450,000 elements only takes 5-10 minutes, much of that time being variable input time. The program can create input decks for ANSYS, ABAQUS and NASTRAN. An archive/retrieval system permits creation of complete trade studies, varying cell size, depth, and petal size, suspension geometry with the ability to recall a particular set of parameters and make small or large changes with ease. The input decks created by the modeler are text files which can be modified by any editor, all the key shell thickness parameters are accessible and comments in deck identify which groups of elements are associated with these parameters. This again makes optimization easier. With ANSYS decks, the nodes representing support attachments are grouped into components; in ABAQUS these are SETS and in NASTRAN as GRIDPOINT SETS, this make integration of these models into large telescope or satellite models easier.

  10. Next-Generation Lightweight Mirror Modeling Software

    Science.gov (United States)

    Arnold, William R., Sr.; Fitzgerald, Mathew; Rosa, Rubin Jaca; Stahl, Phil

    2013-01-01

    The advances in manufacturing techniques for lightweight mirrors, such as EXELSIS deep core low temperature fusion, Corning's continued improvements in the Frit bonding process and the ability to cast large complex designs, combined with water-jet and conventional diamond machining of glasses and ceramics has created the need for more efficient means of generating finite element models of these structures. Traditional methods of assembling 400,000 + element models can take weeks of effort, severely limiting the range of possible optimization variables. This paper will introduce model generation software developed under NASA sponsorship for the design of both terrestrial and space based mirrors. The software deals with any current mirror manufacturing technique, single substrates, multiple arrays of substrates, as well as the ability to merge submodels into a single large model. The modeler generates both mirror and suspension system elements, suspensions can be created either for each individual petal or the whole mirror. A typical model generation of 250,000 nodes and 450,000 elements only takes 5-10 minutes, much of that time being variable input time. The program can create input decks for ANSYS, ABAQUS and NASTRAN. An archive/retrieval system permits creation of complete trade studies, varying cell size, depth, and petal size, suspension geometry with the ability to recall a particular set of parameters and make small or large changes with ease. The input decks created by the modeler are text files which can be modified by any editor, all the key shell thickness parameters are accessible and comments in deck identify which groups of elements are associated with these parameters. This again makes optimization easier. With ANSYS decks, the nodes representing support attachments are grouped into components; in ABAQUS these are SETS and in NASTRAN as GRIDPOINT SETS, this make integration of these models into large telescope or satellite models possible

  11. Lightweight composites for modular panelized construction

    Science.gov (United States)

    Vaidya, Amol S.

    Rapid advances in construction materials technology have enabled civil engineers to achieve impressive gains in the safety, economy, and functionality of structures built to serve the common needs of society. Modular building systems is a fast-growing modern, form of construction gaining recognition for its increased efficiency and ability to apply modern technology to the needs of the market place. In the modular construction technique, a single structural panel can perform a number of functions such as providing thermal insulation, vibration damping, and structural strength. These multifunctional panels can be prefabricated in a manufacturing facility and then transferred to the construction site. A system that uses prefabricated panels for construction is called a "panelized construction system". This study focuses on the development of pre-cast, lightweight, multifunctional sandwich composite panels to be used for panelized construction. Two thermoplastic composite panels are proposed in this study, namely Composite Structural Insulated Panels (CSIPs) for exterior walls, floors and roofs, and Open Core Sandwich composite for multifunctional interior walls of a structure. Special manufacturing techniques are developed for manufacturing these panels. The structural behavior of these panels is analyzed based on various building design codes. Detailed descriptions of the design, cost analysis, manufacturing, finite element modeling and structural testing of these proposed panels are included in this study in the of form five peer-reviewed journal articles. The structural testing of the proposed panels involved in this study included flexural testing, axial compression testing, and low and high velocity impact testing. Based on the current study, the proposed CSIP wall and floor panels were found satisfactory, based on building design codes ASCE-7-05 and ACI-318-05. Joining techniques are proposed in this study for connecting the precast panels on the construction

  12. General Neveu-Schwarz Correlators in Super Liouville Theory

    CERN Document Server

    Abdalla, Elcio; Dalmazi, D; Harada, K; Harada, Koji

    1991-01-01

    In this paper we compute the N-point correlation functions of the tachyon operator from the Neveu Schwarz sector of super Liouville theory coupled to matter fields (with $\\hat c\\le 1$) in the super Coulomb gas formulation, on world sheets with spherical topology. We first integrate over the zero mode assuming that the $s$ parameter takes an integer value, subsequently we continue the parameter to an arbitrary real number. We included an arbitrary number of screening charges (s.c.) and as a result, after renormalizing the s.c., the external legs and the cosmological constant, the form of the final amplitudes do not modify. Remarkably, the result is completely parallel to the bosonic case. We also completed a discussion on the calculation of bosonic correlators including arbitrary screening charges.

  13. Correlation Functions in non critical (super) string theory

    CERN Document Server

    Abdalla, Elcio; Dalmazi, D; Harada, K

    1992-01-01

    We consider the correlation functions of the tachyon vertex operator of the super Liouville theory coupled to matter fields in the super Coulomb gas formulation, on world sheets with spherical topology. After integrating over the zero mode and assuming that the $s$ parameter takes an integer value, we subsequently continue it to an arbitrary real number and compute the correlators in a closed form. We also included an arbitrary number of screening charges and, as a result, after renormalizing them, as well as the external legs and the cosmological constant, the form of the final amplitudes do not modify. The result is remarkably parallel to the bosonic case. For completeness, we discussed the calculation of bosonic correlators including arbitrary screening charges.

  14. Characterization of Polyimide Foams for Ultra-Lightweight Space Structures

    Science.gov (United States)

    Meador, Michael (Technical Monitor); Hillman, Keithan; Veazie, David R.

    2003-01-01

    Ultra-lightweight materials have played a significant role in nearly every area of human activity ranging from magnetic tapes and artificial organs to atmospheric balloons and space inflatables. The application range of ultra-lightweight materials in past decades has expanded dramatically due to their unsurpassed efficiency in terms of low weight and high compliance properties. A new generation of ultra-lightweight materials involving advanced polymeric materials, such as TEEK (TM) polyimide foams, is beginning to emerge to produce novel performance from ultra-lightweight systems for space applications. As a result, they require that special conditions be fulfilled to ensure adequate structural performance, shape retention, and thermal stability. It is therefore important and essential to develop methodologies for predicting the complex properties of ultra-lightweight foams. To support NASA programs such as the Reusable Launch Vehicle (RLV), Clark Atlanta University, along with SORDAL, Inc., has initiated projects for commercial process development of polyimide foams for the proposed cryogenic tank integrated structure (see figure 1). Fabrication and characterization of high temperature, advanced aerospace-grade polyimide foams and filled foam sandwich composites for specified lifetimes in NASA space applications, as well as quantifying the lifetime of components, are immensely attractive goals. In order to improve the development, durability, safety, and life cycle performance of ultra-lightweight polymeric foams, test methods for the properties are constant concerns in terms of timeliness, reliability, and cost. A major challenge is to identify the mechanisms of failures (i.e., core failure, interfacial debonding, and crack development) that are reflected in the measured properties. The long-term goal of the this research is to develop the tools and capabilities necessary to successfully engineer ultra-lightweight polymeric foams. The desire is to reduce density

  15. Microsphere Super-resolution Imaging

    CERN Document Server

    Wang, Zengbo

    2015-01-01

    Recently, it was discovered that microsphere can generate super-resolution focusing beyond diffraction limit. This has led to the development of an exciting super-resolution imaging technique -microsphere nanoscopy- that features a record resolution of 50 nm under white lights. Different samples have been directly imaged in high resolution and real time without labelling, including both non-biological (nano devices, structures and materials) and biological (subcellular details, viruses) samples. This chapter reviews the technique, which covers its background, fundamentals, experiments, mechanisms as well as the future outlook.

  16. Interactive Super Mario Bros Evolution

    DEFF Research Database (Denmark)

    Sørensen, Patrikk D.; Olsen, Jeppeh M.; Risi, Sebastian

    2016-01-01

    to encourage the evolution of desired behaviors. In this paper, we show how casual users can create controllers for \\emph{Super Mario Bros} through an interactive evolutionary computation (IEC) approach, without prior domain or programming knowledge. By iteratively selecting Super Mario behaviors from a set...... of candidates, users are able to guide evolution towards a variety of different behaviors, which would be difficult with an automated approach. Additionally, the user-evolved controllers perform similarly well as controllers evolved with a traditional fitness-based approach when comparing distance traveled...

  17. Quantisation of super Teichmueller theory

    Energy Technology Data Exchange (ETDEWEB)

    Aghaei, Nezhla [DESY Hamburg (Germany). Theory Group; Hamburg Univ. (Germany). Dept. of Mathematics; Pawelkiewicz, Michal; Techner, Joerg [DESY Hamburg (Germany). Theory Group

    2015-12-15

    We construct a quantisation of the Teichmueller spaces of super Riemann surfaces using coordinates associated to ideal triangulations of super Riemann surfaces. A new feature is the non-trivial dependence on the choice of a spin structure which can be encoded combinatorially in a certain refinement of the ideal triangulation. By constructing a projective unitary representation of the groupoid of changes of refined ideal triangulations we demonstrate that the dependence of the resulting quantum theory on the choice of a triangulation is inessential.

  18. Quantisation of super Teichmueller theory

    CERN Document Server

    Aghaei, Nezhla; Teschner, Joerg

    2015-01-01

    We construct a quantisation of the Teichmueller spaces of super Riemann surfaces using coordinates associated to ideal triangulations of super Riemann surfaces. A new feature is the non-trivial dependence on the choice of a spin structure which can be encoded combinatorially in a certain refinement of the ideal triangulation. By constructing a projective unitary representation of the groupoid of changes of refined ideal triangulations we demonstrate that the dependence of the resulting quantum theory on the choice of a triangulation is inessential.

  19. The construction of orthodox super rpp semigroups

    Institute of Scientific and Technical Information of China (English)

    HE Yong; GUO Yuqi; Kar Ping Shum

    2004-01-01

    We define orthodox super rpp semigroups and study their semilattice decompositions. Standard representation theorem of orthodox super rpp semigroups whose subband of idempotents is in the varieties of bands described by an identity with at most three variables are obtained.

  20. The External Degree.

    Science.gov (United States)

    Houle, Cyril O.

    This book examines the external degree in relation to the extremes of attitudes, myths, and data. Emphasis is placed on the emergence of the American external degree, foreign external-degree programs, the purpose of the external degree, the current scene, institutional issues, and problems of general policy. (MJM)

  1. Lightweight design of the rectangular mirror using topology optimization

    Science.gov (United States)

    Xiang, Meng; Li, Fu

    2014-09-01

    That minimizing the mass of space optical remote sensor at the same time guaranteeing of structural rigidity and surface shape accuracy, became a new critical research topic. This paper achieves detailed design of meniscus rectangular lens body structure by taking the choice of materials, design of supporting structure and lightweight form of mirror into account. And we established lightweight concrete of the mirror under self-weight by the method of topological optimization design. For the optimization, we used a 3-D model of the rectangular mirror and calculated based on that making minimum weight of the mirror as an objective function constrained by the displacement of the mirror surface. Finally finite element analysis method was adopted to get the optimization results analyzed and compared with the traditional triangular lightweight model. Analysis results prove that: the new mirror is superior to the traditional model in surface accuracy and structural rigidity, PV value, RMS value and the lightweight rate. With enough high dynamic-static stiffness and thermal stability, this kind of mirror can meet the demand under the self-weight and the random vibration environment respectively. So this article puts forward a new idea in the lightweight design of rectangular mirror.

  2. Super-resolution Phase Tomography

    KAUST Repository

    Depeursinge, Christian

    2013-04-21

    Digital Holographic Microscopy (DHM) yields reconstructed complex wavefields. It allows synthesizing the aperture of a virtual microscope up to 2π, offering super-resolution phase images. Live images of micro-organisms and neurons with resolution less than 100 nm are presented.

  3. Super Rice Breeding in China

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@I. Demand for super high yield rice in China   Rice is one of the main staple food in China. The performance of rice sector in production and yield had been very impressive in the last four decades. However, rice production and yield has stagnated since 1990.

  4. Super Girls Still Center Stage

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The TV singing contest continues to draw a devoted audience, but will its impact on Chinese culture fall away like a shooting star? Ask any teenage girl in China to name the finalists of last year's Super Girl show and chances are she will instantly come up with the three big names.She'll probable

  5. Analysis of Forensic Super Timelines

    Science.gov (United States)

    2012-06-14

    BIB .1  vii List of Figures Figure Page...Hacker disconnects from User’s system  User clicks off Screen Saver  User closes Solitaire program  User logs off system BIB .1...analysis- tapestry_33836. BIB .2 Guðjónsson, K. (2010). Mastering the super timeline with log2timeline. SANS Gold Paper accepted June 29,2010

  6. Plastic shrinkage of mortars with shrinkage reducing admixture and lightweight aggregates studied by neutron tomography

    Energy Technology Data Exchange (ETDEWEB)

    Wyrzykowski, Mateusz, E-mail: mateusz.wyrzykowski@empa.ch [Empa, Swiss Federal Laboratories for Materials Science and Technology, Concrete and Construction Chemistry Laboratory, Dübendorf (Switzerland); Lodz University of Technology, Department of Building Physics and Building Materials, Lodz (Poland); Trtik, Pavel [Paul Scherrer Institute, Laboratory for Neutron Scattering and Imaging, Villigen (Switzerland); Empa, Swiss Federal Laboratories for Materials Science and Technology, Concrete and Construction Chemistry Laboratory, Dübendorf (Switzerland); Münch, Beat [Empa, Swiss Federal Laboratories for Materials Science and Technology, Concrete and Construction Chemistry Laboratory, Dübendorf (Switzerland); Weiss, Jason [Purdue University, School of Civil Engineering, West Lafayette (United States); Vontobel, Peter [Paul Scherrer Institute, Laboratory for Neutron Scattering and Imaging, Villigen (Switzerland); Lura, Pietro [Empa, Swiss Federal Laboratories for Materials Science and Technology, Concrete and Construction Chemistry Laboratory, Dübendorf (Switzerland); ETH Zurich, Institute for Building Materials (IfB), Zurich (Switzerland)

    2015-07-15

    Water transport in fresh, highly permeable concrete and rapid water evaporation from the concrete surface during the first few hours after placement are the key parameters influencing plastic shrinkage cracking. In this work, neutron tomography was used to determine both the water loss from the concrete surface due to evaporation and the redistribution of fluid that occurs in fresh mortars exposed to external drying. In addition to the reference mortar with a water to cement ratio (w/c) of 0.30, a mortar with the addition of pre-wetted lightweight aggregates (LWA) and a mortar with a shrinkage reducing admixture (SRA) were tested. The addition of SRA reduced the evaporation rate from the mortar at the initial stages of drying and reduced the total water loss. The pre-wetted LWA released a large part of the absorbed water as a consequence of capillary pressure developing in the fresh mortar due to evaporation.

  7. Optimum Design of Lightweight Silicon Carbide Mirror Assembly

    Institute of Scientific and Technical Information of China (English)

    HAN Yuanyuan; ZHANG Yumin; HAN Jiecai; ZHANG Jianhan; YAO Wang; ZHOU Yufeng

    2008-01-01

    According to the design requirement and on the basis of the principle that the thermal expansion coefficient of the support structure should match with that of the mirror, a lightweight silicon carbide primary mirror assembly was designed. Finite element analysis combined with the parameter-optimized method was used during the design. Lightweight cell and rigid rib structure were used for the mirror assembly. The static, dynamic and thermal properties of the primary mirror assembly were analyzed. It is shown that after optimization, the lightweight ratio of the silicon carbide mirror is 52.5%, and the rigidity of the silicon carbide structure is high enough to support the required mirror. When temperature changes, the deformation of the mirror surface is in proportion to the temperature difference.

  8. Second law evaluation of a lightweight cooling unit

    Directory of Open Access Journals (Sweden)

    Guilherme B. Ribeiro

    2016-03-01

    Full Text Available The analysis based on the second law of thermodynamics of a lightweight vapor compression refrigeration system is presented. A small-scale linear compressor was applied in a DC-powered portable cooler for vehicles and for the medical field, using finned-tube heat exchangers and R600-a (Isobutane as the working fluid. The cooler was tested in an environmental chamber (with controlled temperature and humidity under three different ambient temperatures (21, 25 and 32 °C in order to measure key parameters of the system, such as cooling capacity, power consumption and internal air temperature. For the comparison of thermodynamic irreversibilities, a conventional vapor compression refrigerating system was also tested under the same ambient conditions. Results indicated that the system with the proposed lightweight system kept the lowest internal air temperature with higher coefficients of performance, showing how a lightweight cooling unit can enlarge the use of refrigerating systems due to its attributes.

  9. Bond Strength Degradation of Corrosive Reinforced Lightweight Concrete

    Institute of Scientific and Technical Information of China (English)

    CHEN Yueshun; LU Yiyan; LI Houxiang; ZENG Sanhai

    2007-01-01

    The influence of reinforced bar corrosion on the bond degradation in lightweight concrete was studied. Accelerated constant current corrosion tests were performed on lightweight reinforced concrete samples, and the influential factors, such as protective layer thickness, reinforced bar diameter and corrosive level were investigated. The constant current step method was used to measure the electric resistance of the concrete protective cover, which was used to characterize the corrosion level of the rebar. Experimental results indicated that the corrosive resistance increased with increasing the cover dimension and decreasing the reinforced bar diameter, and the rate of decrease in the specimen impedance after cracking depended on the cover dimension. A new medium was offered for the further research on the performance degradation of corrosion lightweight concrete.

  10. Physique characteristics of Pan American Games lightweight rowers.

    Science.gov (United States)

    DeRose, E H; Crawford, S M; Kerr, D A; Ward, R; Ross, W D

    1989-08-01

    The emergence of lightweight rowing as an international sport has made the optimization of physique within the weight restrictions a matter of primary importance in selection and training of the participants. The occasion of the Xth Pan American Games provided opportunity to obtain comprehensive anthropometric data on 20 male and 13 female lightweight rower finalists including most of the medal winners. Anthropometric characteristics, somatotype, and proportionality profiles showed the male rowers to be similar in most aspects to a student control sample, with the exception of short sitting height and large transverse chest breadth. The females, on the other hand, appeared to be very different from the control sample, having a number of characteristics similar to those of Olympic rowers. The female lightweight rowers also uniquely demonstrated two distinct physique prototypes.

  11. Autogenous Shrinkage of High Strength Lightweight Aggregate Concrete

    Institute of Scientific and Technical Information of China (English)

    DING Qingjun; TIAN Yaogang; WANG Fazhou; ZHANG Feng; HU Shuguang

    2005-01-01

    The characteristic of autogenous shrinkage ( AS ) and its effect on high strength lightweight aggregate concrete (HSLAC) were studied. The experimental results show that the main shrinkage of high strength concrete is AS and the amount of cement can affect the AS of HSLAC remarkably. At the early stage the AS of HSLAC is lower than that of high strength normal concrete, but it has a large growth at the later stage. The AS of high strength normal concrete becomes stable at 90d age, but HSLAC still has a high AS growth. It is found that adjusting the volume rate of lightweight aggregate, mixing with a proper dosage of fly ash and raising the water saturation degree of lightweight aggregate can markedly reduce the AS rate of HSLAC.

  12. The lightweight structure design of a CFRP mirror

    Science.gov (United States)

    Ding, Jiaoteng; Xu, Liang; Ma, Zhen; Xie, Yongjie; Luo, Yao; Wang, Yongjie; Pang, Zhihai

    2016-10-01

    The advantage of Carbon Fiber Reinforced Polymer (CFRP) is obvious as a common space material for low density, low thermal expansion coefficient and high specific stiffness characteristics, it is the ideal material choice for space optical reflector. Mirror structure with honeycomb can achieve high rates of lightweight, as well as high specific stiffness. For Φ300mm CFRP mirror, accounting of the actual process properties of CFRP, mirror panels laminated based on thermal stability design, honeycomb fabricated using one innovative inlaying-grafting design method. Finally, lightweight structure design of the CFRP primary mirror completed, the thermal stability result of the Φ300mm CFRP mirror achieved is 10nm°C.

  13. Overview of Lightweight Structures for Rotorcraft Engines and Drivetrains

    Science.gov (United States)

    Roberts, Gary D.

    2011-01-01

    This is an overview presentation of research being performed in the Advanced Materials Task within the NASA Subsonic Rotary Wing Project. This research is focused on technology areas that address both national goals and project goals for advanced rotorcraft. Specific technology areas discussed are: (1) high temperature materials for advanced turbines in turboshaft engines; (2) polymer matrix composites for lightweight drive system components; (3) lightweight structure approaches for noise and vibration control; and (4) an advanced metal alloy for lighter weight bearings and more reliable mechanical components. An overview of the technology in each area is discussed, and recent accomplishments are presented.

  14. Ground Fluidization Promotes Rapid Running of a Lightweight Robot

    Science.gov (United States)

    2013-01-01

    Ground fluidization promotes rapid running of a lightweight robot The International Journal of Robotics Research 32(7) 859–869 © The Author(s) 2013...continuously fluidized , and the robot “swam” forward slowly (∼ 0.01 body length/s) using drag on the legs to overcome belly drag. In contrast, a variety of...COVERED 00-00-2013 to 00-00-2013 4. TITLE AND SUBTITLE Ground fluidization promotes rapid running of a lightweight robot 5a. CONTRACT NUMBER 5b

  15. Development of light-weight spherical mirrors for RICH detectors

    CERN Document Server

    Metlica, Fabio

    2007-01-01

    Glass-coated beryllium and carbon-fiber light-weight spherical mirrors, with radii of curvature of $\\sim$ 2700mm, have been successfully developed and tested as part of the LHCb RICH experimental programme. The low mass mirror is necessary to minimize the amount of material within the LHCb spectrometer acceptance, with a requirement of less than 2% of a radiation length. Both technologies are suitable for light-weight mirror applications. The R&D and characterization of the mirrors are reported.

  16. Prediction of Noise Transmission in Lightweight Building Structures

    DEFF Research Database (Denmark)

    Dickow, Kristoffer Ahrens

    tool to predict the flanking transmission of air-borne and structure borne sound already at the design stage. However, lightweight building structures typically do not meet the requirements for ideal SEA subsystems and, therefore, applying the EN 12354 standard to lightweight building structures may...... papers are carried out as parametric studies in the commercial FE package ABAQUS. Finally, an experimental part, that focuses on the uncertainty and variation in wooden junctions, is included. Ten nominally identical plate/beam T-junctions are tested using experimental modal analysis, and the results...

  17. Evaluation and comparison of a lightweight bamboo composite

    Science.gov (United States)

    Loth, Andreas; Berwing, Michael; Förster, Ralf

    2016-10-01

    The demand for fast changing production lines and other facilities needs new lightweight and stable systems for partitioning walls. There is also a need for ecological products for this application. The wood like grass bamboo provides a wide potential to substitute conventional wood. A composite lightweight honeycomb like bamboo board was developed and compared with reinforced and unreinforced plywood specimen. The acquired mechanical properties gave a promising result for the usability of bamboo as basis material for wide span boards. It can be manufactured with minimal technical investments, that suits also well for regions with little industry. The ecological assessment of the structure is very positive.

  18. Reflective Coating for Lightweight X-Ray Optics

    Science.gov (United States)

    Chan, Kai-Wing; Zhang, William W.; Windt, David; Hong, Mao-Ling; Saha, Timo; McClelland, Ryan; Sharpe, Marton; Dwivedi, Vivek H.

    2012-01-01

    X-ray reflective coating for next generation's lightweight, high resolution, optics for astronomy requires thin-film deposition that is precisely fine-tuned so that it will not distort the thin sub-mm substrates. Film of very low stress is required. Alternatively, mirror distortion can be cancelled by precisely balancing the deformation from multiple films. We will present results on metallic film deposition for the lightweight optics under development. These efforts include: low-stress deposition by magnetron sputtering and atomic layer deposition of the metals, balancing of gross deformation with two-layer depositions of opposite stresses and with depositions on both sides of the thin mirrors.

  19. Regulating multiple externalities

    DEFF Research Database (Denmark)

    Waldo, Staffan; Jensen, Frank; Nielsen, Max

    2016-01-01

    Open access is a well-known externality problem in fisheries causing excess capacity and overfishing. Due to global warming, externality problems from CO2 emissions have gained increased interest. With two externality problems, a first-best optimum can be achieved by using two regulatory instrume......Open access is a well-known externality problem in fisheries causing excess capacity and overfishing. Due to global warming, externality problems from CO2 emissions have gained increased interest. With two externality problems, a first-best optimum can be achieved by using two regulatory...

  20. Super-translations and super-rotations at the horizon

    CERN Document Server

    Donnay, Laura; Gonzalez, Hernan A; Pino, Miguel

    2015-01-01

    We show that the asymptotic symmetries close to non-extremal black hole horizons are generated by an extension of super-translations. This group is generated by a semi-direct sum of Virasoro and abelian currents. The charges associated to the asymptotic Killing symmetries satisfy the same algebra. When considering the special case of the stationary black hole, the zero mode charges correspond to the angular momentum and the entropy at the horizon.

  1. Lightweight High Temperature Non-Eroding Throat Materials for Propulsion Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The innovation in this proposed effort is the development of lightweight, non-eroding nozzle materials for use in propulsion systems. Lightweight structures are...

  2. Strength properties of cement slurries with lightweights applied in oil and gas wells

    Science.gov (United States)

    Bubnov, A. S.; Boyko, I. A.; Khorev, V. S.

    2015-02-01

    The article is focused on the cement stone strength properties resulted from lightweight cement slurries that meet GOST-1581-96 (state Standards) requirements. Exfoliated vermiculite, hollow aluminosilicate microspheres (HAMs), diatomite and perlite were used as lightweighting additives.

  3. ExternE National Implementation Finland

    Energy Technology Data Exchange (ETDEWEB)

    Pingoud, K.; Maelkki, H.; Wihersaari, M.; Pirilae, P. [VTT Energy, Espoo (Finland); Hongisto, M. [Imatran Voima Oy, Vantaa (Finland); Siitonen, S. [Ekono Energy Ltd, Espoo (Finland); Johansson, M. [Finnish Environment Institute, Helsinki (Finland)

    1999-07-01

    ExternE National Implementation is a continuation of the ExternE Project, funded in part by the European Commission's Joule III Programme. This study is the result of the ExternE National Implementation Project for Finland. Three fuel cycles were selected for the Finnish study: coal, peat and wood-derived biomass, which together are responsible for about 40% of total electricity generation in Finland and about 75% of the non-nuclear fuel based generation. The estimated external costs or damages were dominated by the global warming (GW) impacts in the coal and peat fuel cycles, but knowledge of the true GW impacts is still uncertain. From among other impacts that were valued in monetary terms the human health damages due to airborne emissions dominated in all the three fuel cycles. Monetary valuation for ecosystem impacts is not possible using the ExternE methodology at present. The Meri-Pori power station representing the coal fuel cycle is one of the world's cleanest and most efficient coal-fired power plants with a condensing turbine. The coal is imported mainly from Poland. The estimated health damages were about 4 mECU/kWh, crop damages an order of magnitude lower and damages caused to building materials two orders of magnitude lower. The power stations of the peat and biomass fuel cycles are of CHP type, generating electricity and heat for the district heating systems of two cities. Their fuels are of domestic origin. The estimated health damages allocated to electricity generation were about 5 and 6 mECU/kWh, respectively. The estimates were case-specific and thus an generalisation of the results to the whole electricity generation in Finland is unrealistic. Despite the uncertainties and limitations of the methodology, it is a promising tool in the comparison of similar kinds of fuel cycles, new power plants and pollution abatement technologies and different plant locations with each other. (orig.)

  4. Experimental study on the effect of volcanic residue on the performance of recycled lightweight aggregate concrete

    Science.gov (United States)

    Xiao, Li-guang; Li, Ji-heng; Liu, Qing-shun

    2017-08-01

    Recycled lightweight aggregate concrete prepared with waste brick recycled light aggregate has high water absorption, large apparent density and poor frost resistance. The technical measures of regen-erating lightweight aggregate concrete with modified waste bricks from volcanic slag are put forward. The effects of volcanic slag on the properties of waste lightweight aggregate concrete were studied. The experi-mental results show that volcanic slag can significantly reduce the apparent density of recycled lightweight aggregate concrete and improve its frost resistance.

  5. 伦敦SuperDesign展

    Institute of Scientific and Technical Information of China (English)

    柚子

    2011-01-01

    近日,英国伦敦Super Design展在伦敦Wakefield大街的The Dairy展厅如期举行。本次展览展出了来自包括知名设计师和新兴设计师的特别定制的工作室作品:到如今已经是第五个年头的伦敦Super Deslgn展,力图强发展,展出形式别出心裁、独树一帜,从一个崭新.活跃的角度集展示当代艺术。

  6. Super-stable Poissonian structures

    Science.gov (United States)

    Eliazar, Iddo

    2012-10-01

    In this paper we characterize classes of Poisson processes whose statistical structures are super-stable. We consider a flow generated by a one-dimensional ordinary differential equation, and an ensemble of particles ‘surfing’ the flow. The particles start from random initial positions, and are propagated along the flow by stochastic ‘wave processes’ with general statistics and general cross correlations. Setting the initial positions to be Poisson processes, we characterize the classes of Poisson processes that render the particles’ positions—at all times, and invariantly with respect to the wave processes—statistically identical to their initial positions. These Poisson processes are termed ‘super-stable’ and facilitate the generalization of the notion of stationary distributions far beyond the realm of Markov dynamics.

  7. Super-Kamiokande atmospheric neutrinos

    Energy Technology Data Exchange (ETDEWEB)

    Moriyama, S. [Kamioka Observatory, Institute for Cosmic Ray Research, University of Tokyo, Higashi Mozumi, Hida city, Gifu prefecture (Japan)

    2005-08-15

    Results on atmospheric neutrino analysis at Super-Kamiokande I is presented. The whole data set of atmospheric neutrino sample in Super-Kamiokande I is consistently explained with an assumption of pure {nu}{sub {mu}}-{nu}{sub {tau}} oscillations. The allowed range of parameters is 1.5x10{sup -3}<{delta}m{sup 2}<3.4x10{sup -3} eV{sup 2} and sin{sup 2}2{theta}>0.92 at 90% C.L. In the oscillation analysis, we improved the treatment of systematic errors so that they can be considered as independent. This makes possible to find which systematic errors have larger effect on the analysis results. Some sensitivity studies under several assumptions of improvements in systematic errors are presented.

  8. ASH External Web Portal (External Portal) -

    Data.gov (United States)

    Department of Transportation — The ASH External Web Portal is a web-based portal that provides single sign-on functionality, making the web portal a single location from which to be authenticated...

  9. The Era of Super Capitalism

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The world has entered the "super capitalism" era when one third of its economic activities are controlled by less than 3 percent of global financial capital. This year,a global economic recession,triggered by the U.S. subprime mortgage crisis,seems unavoidable. To tackle international financial problems,Tao Dong,Chief Economist for Asia at Credit Suisse First Boston in Hong Kong,shared his insights with China Business Journal. Excerpts follow.

  10. Evaluation of Flanking Noise Transmission within Periodically Distributed Lightweight Beam Elements

    DEFF Research Database (Denmark)

    Domadiya, Parthkumar Gandalal; Andersen, Lars Vabbersgaard; Sorokin, Sergey

    2012-01-01

    Wooden frame structures are highly preferred as lightweight building systems nowadays. Lightweight building structures have gained more interest due to lower cost of production. However, there is a growing concern regarding noise and vibration issues within lightweight structures. Sound may pass...

  11. Effect of Commercial Synthappret BAP Treatment on the Tailorabilitv of Light-Weight Worsted Wool Fabrics

    Institute of Scientific and Technical Information of China (English)

    Wang Gehui(王革辉); Zhang Weiyuan(张渭源); Postle, R.; Phillips, D.

    2001-01-01

    By means of measurement with the FAST instruments,the effect of commercial Synthappret BAP treatment on the tailorability of light-weight wool worsted fabrics has been investigated. It was found that the commercial Synthappret BAP treatment improved the tailorability of the light-weight wool fabrics mainly by increasing the bending stiffness of the light-weight wool fabrics.

  12. Density Optimization of Lithium Lanthanum Titanate Ceramics for Lightweight Lithium-Air Batteries

    Science.gov (United States)

    2014-11-01

    Density Optimization of Lithium Lanthanum Titanate Ceramics for Lightweight Lithium -Air Batteries by Claire Weiss Brennan, Victoria Blair...Ground, MD 21005-5069 ARL-TR-7145 November 2014 Density Optimization of Lithium Lanthanum Titanate Ceramics for Lightweight Lithium -Air...COVERED (From - To) 1 June–31 August 2014 4. TITLE AND SUBTITLE Density Optimization of Lithium Lanthanum Titanate Ceramics for Lightweight Lithium

  13. BEWARE OF...SUPER GLUES!!

    CERN Multimedia

    2006-01-01

    What happened? A number of accidents have occurred with the use of 'Super Glues'. Some individuals have suffered injuries - severe irritation, or skin bonded together - through getting glue on their face and in their eyes. What are the hazards associated with glues? 'Super Glues' (i.e. cyanoacrylates): Are harmful if swallowed and are chemical irritants to the eyes, respiratory system and skin. Present the risk of polymerization (hardening) leading to skin damage. Be careful ! 'Super Glues' can bond to skin and eyes in seconds. Note: Other glues, resins and hardeners are also chemicals and as such can cause serious damage to the skin, eyes, respiratory or digestive tract. (For example: some components can be toxic, harmful, corrosive, sensitizing agents, etc.). How to prevent accidents in the future? Read the Material Safety Data Sheet (MSDS) for all of the glues you work with. Check the label on the container to find out which of the materials you work with are hazardous. Wear the right Per...

  14. Super-Eccentric Migrating Jupiters

    CERN Document Server

    Socrates, Aristotle; Dong, Subo; Tremaine, Scott

    2011-01-01

    An important class of formation theories for hot Jupiters involves the excitation of extreme orbital eccentricity (e=0.99 or even larger) followed by tidal dissipation at periastron passage that eventually circularizes the planetary orbit at a period less than 10 days. In a steady state, this mechanism requires the existence of a significant population of super-eccentric (e>0.9) migrating Jupiters with long orbital periods and periastron distances of only a few stellar radii. For these super-eccentric planets, the periastron is fixed due to conservation of orbital angular momentum and the energy dissipated per orbit is constant, implying that the rate of change in semi-major axis a is \\dot a \\propto a^0.5 and consequently the number distribution satisfies dN/dlog a\\propto a^0.5. If this formation process produces most hot Jupiters, Kepler should detect several super-eccentric migrating progenitors of hot Jupiters, allowing for a test of high-eccentricity migration scenarios.

  15. SUPER-ECCENTRIC MIGRATING JUPITERS

    Energy Technology Data Exchange (ETDEWEB)

    Socrates, Aristotle; Katz, Boaz; Dong Subo; Tremaine, Scott [Institute for Advanced Study, Princeton, NJ 08540 (United States)

    2012-05-10

    An important class of formation theories for hot Jupiters involves the excitation of extreme orbital eccentricity (e = 0.99 or even larger) followed by tidal dissipation at periastron passage that eventually circularizes the planetary orbit at a period less than 10 days. In a steady state, this mechanism requires the existence of a significant population of super-eccentric (e > 0.9) migrating Jupiters with long orbital periods and periastron distances of only a few stellar radii. For these super-eccentric planets, the periastron is fixed due to conservation of orbital angular momentum and the energy dissipated per orbit is constant, implying that the rate of change in semi-major axis a is a-dot {proportional_to}a{sup 1/2} and consequently the number distribution satisfies dN/d log a{proportional_to}a{sup 1/2}. If this formation process produces most hot Jupiters, Kepler should detect several super-eccentric migrating progenitors of hot Jupiters, allowing for a test of high-eccentricity migration scenarios.

  16. A purely flexible lightweight membrane-type acoustic metamaterial

    Science.gov (United States)

    Ma, Fuyin; Wu, Jiu Hui; Huang, Meng; Zhang, Weiquan; Zhang, Siwen

    2015-05-01

    This paper proposes a purely flexible lightweight membrane-type acoustic structure, wherein one kind of flexible lightweight rubber material takes the roles of mass and stiffness and another type of lightweight flexible EVA (ethylene-vinyl acetate copolymer) or plastic material functions as the localized stiffness for each unit. Because both the scatterers and base are constituted by the same material, this type of structure breaks the limitation that the metamaterials and phononic crystals need different materials with relatively large density and elasticity modulus ratios to play the roles of the scatterers and base respectively. Based on the band structures with different units, mass block shapes and size parameters, it is suggested that the shapes of the mass block can significantly affect the band structure. In addition, this type of structure could not only open a full band gap in the low-frequency range below 500 Hz, but also obtain an ultra-low-frequency bending wave band gap in the range below 100 Hz. Finally, we take into account the semi-infinite medium as a component, and calculate the sound transmission loss (STL) to evaluate the interaction between the structure and air. An experimental validation employing the cylindrical mass structure was developed to directly support the simulation results. Since the structures proposed in this study have achieved a purely flexible lightweight design, there exists an important promotion effect to realize the engineering applications of the acoustic metamaterials in practice.

  17. A Lightweight Intelligent Virtual Cinematography System for Machinima Production

    Science.gov (United States)

    2007-01-01

    A Lightweight Intelligent Virtual Cinematography System for Machinima Production David K. Elson1, Mark O. Riedl2 1Columbia University, Computer...However, creating quality cinematic visualizations with existing machinima techniques still requires a high degree of talent and effort. We...produces a cinematic visualization. Unlike other virtual cinematography systems, Cambot favors an offline algorithm coupled with an extensible

  18. Lightweight Inexpensive Ozone Lidar Telescope Using a Plastic Fresnel Lens

    Science.gov (United States)

    DeYoung, Russell J.; Notari, Anthony; Carrion, William; Pliutau, Denis

    2014-01-01

    An inexpensive lightweight ozone lidar telescope was designed, constructed and operated during an ozone lidar field campaign. This report summarizes the design parameters and performance of the plastic Fresnel lens telescope and shows the ozone lidar performance compared to Zemax calculations.

  19. FY2010 Annual Progress Report for Lightweighting Materials

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2011-01-15

    The Lightweight Materials activity (LM) within the Vehicle Technologies Program focuses on the development and validation of advanced materials and manufacturing technologies to significantly reduce light and heavy duty vehicle weight without compromising other attributes such as safety, performance, recyclability, and cost.

  20. STRENGTH OF NANOMODIFIED HIGH-STRENGTH LIGHTWEIGHT CONCRETES

    Directory of Open Access Journals (Sweden)

    NOZEMTСEV Alexandr Sergeevich

    2013-02-01

    Full Text Available The paper presents the results of research aimed at development of nanomodified high-strength lightweight concrete for construction. The developed concretes are of low average density and high ultimate compressive strength. It is shown that to produce this type of concrete one need to use hollow glass and aluminosilicate microspheres. To increase the durability of adhesion between cement stone and fine filler the authors offer to use complex nanodimensinal modifier based on iron hydroxide sol and silica sol as a surface nanomodifier for hollow microspheres. It is hypothesized that the proposed modifier has complex effect on the activity of the cement hydration and, at the same time increases bond strength between filler and cement-mineral matrix. The compositions for energy-efficient nanomodified high-strength lightweight concrete which density is 1300…1500 kg/m³ and compressive strength is 40…65 MPa have been developed. The approaches to the design of high-strength lightweight concrete with density of less than 2000 kg/m³ are formulated. It is noted that the proposed concretes possess dense homogeneous structure and moderate mobility. Thus, they allow processing by vibration during production. The economic and practical implications for realization of high-strength lightweight concrete in industrial production have been justified.

  1. Lightweighting Impacts on Fuel Economy, Cost, and Component Losses

    Energy Technology Data Exchange (ETDEWEB)

    Brooker, A. D.; Ward, J.; Wang, L.

    2013-01-01

    The Future Automotive Systems Technology Simulator (FASTSim) is the U.S. Department of Energy's high-level vehicle powertrain model developed at the National Renewable Energy Laboratory. It uses a time versus speed drive cycle to estimate the powertrain forces required to meet the cycle. It simulates the major vehicle powertrain components and their losses. It includes a cost model based on component sizing and fuel prices. FASTSim simulated different levels of lightweighting for four different powertrains: a conventional gasoline engine vehicle, a hybrid electric vehicle (HEV), a plug-in hybrid electric vehicle (PHEV), and a battery electric vehicle (EV). Weight reductions impacted the conventional vehicle's efficiency more than the HEV, PHEV and EV. Although lightweighting impacted the advanced vehicles' efficiency less, it reduced component cost and overall costs more. The PHEV and EV are less cost effective than the conventional vehicle and HEV using current battery costs. Assuming the DOE's battery cost target of $100/kWh, however, the PHEV attained similar cost and lightweighting benefits. Generally, lightweighting was cost effective when it costs less than $6/kg of mass eliminated.

  2. Design of Light-Weight High-Entropy Alloys

    Directory of Open Access Journals (Sweden)

    Rui Feng

    2016-09-01

    Full Text Available High-entropy alloys (HEAs are a new class of solid-solution alloys that have attracted worldwide attention for their outstanding properties. Owing to the demand from transportation and defense industries, light-weight HEAs have also garnered widespread interest from scientists for use as potential structural materials. Great efforts have been made to study the phase-formation rules of HEAs to accelerate and refine the discovery process. In this paper, many proposed solid-solution phase-formation rules are assessed, based on a series of known and newly-designed light-weight HEAs. The results indicate that these empirical rules work for most compositions but also fail for several alloys. Light-weight HEAs often involve the additions of Al and/or Ti in great amounts, resulting in large negative enthalpies for forming solid-solution phases and/or intermetallic compounds. Accordingly, these empirical rules need to be modified with the new experimental data. In contrast, CALPHAD (acronym of the calculation of phase diagrams method is demonstrated to be an effective approach to predict the phase formation in HEAs as a function of composition and temperature. Future perspectives on the design of light-weight HEAs are discussed in light of CALPHAD modeling and physical metallurgy principles.

  3. Annotating Evidence Based Clinical Guidelines: A Lightweight Ontology

    NARCIS (Netherlands)

    R. Hoekstra; A. de Waard; R. Vdovjak

    2012-01-01

    This paper describes a lightweight ontology for representing annotations of declarative evidence based clinical guidelines. We present the motivation and requirements for this representation, based on an analysis of several guidelines. The ontology provides the means to connect clinical questions an

  4. Closing the innovation cycle in lightweighting compressor pistons technolog

    NARCIS (Netherlands)

    Wentzel, C.; Eijk, A.; Groenewegen, G.; Bergsma, O.

    2016-01-01

    What started out as an exercise in exploring the weight reduction potential of those allegedly “heavy recip crossheads”, turned out to be a fast leap towards implementation of a new hybrid material concept for very lightweight pistons. This was enabled by a next phase in the EFRC R&D group research

  5. SPONGENT: The Design Space of Lightweight Cryptographic Hashing

    DEFF Research Database (Denmark)

    Bogdanov, Andrey; Knezevic, Miroslav; Leander, Gregor

    2013-01-01

    The design of secure yet efficiently implementable cryptographic algorithms is a fundamental problem of cryptography. Lately, lightweight cryptography--optimizing the algorithms to fit the most constrained environments--has received a great deal of attention, the recent research being mainly...

  6. Solar cell submodule design facilitates assembly of lightweight arrays

    Science.gov (United States)

    Yasui, R. K.

    1966-01-01

    Solar cell submodules with bus bars that leave tabs along one end of the submodule and wires with raised portions along the other end are assembled by interlocking the tabs and wires of adjacent submodules. This structural design is lightweight and reliable and requires no metallic substructure.

  7. APE: Authenticated Permutation-Based Encryption for Lightweight Cryptography

    NARCIS (Netherlands)

    Andreeva, Elena; Bilgin, Begül; Bogdanov, Andrey; Luykx, Atul; Mennink, Bart; Mouha, Nicky; Yasuda, Kan

    The domain of lightweight cryptography focuses on cryptographic algorithms for extremely constrained devices. It is very costly to avoid nonce reuse in such environments, because this requires either a hardware source of randomness, or non-volatile memory to store a counter. At the same time, a lot

  8. Application of CAE technology for Geely car lightweight

    Institute of Scientific and Technical Information of China (English)

    Men Yongxin; Ma Fangwu; Peng Hong; Li Yongsheng

    2012-01-01

    In order to reduce energy consumption and protect the human survival environment, the lightweight has became the development trend of the world automobile industry. On the premise of ensuring the strength, safety and driving performance of the car, the major car enterprises try to reduce the curb weight of the ear, fuel consumption and emissions. Not only a lot of new technologies and new products have been generated, but also joint vehicle development process and computer aided engineering (CAE) analysis technology have been developed. Since the entry into the "Au- tomobile Lightweight Technology Innovation Strategic Alliance" in Dec. 2007, Geely Group has been focusing on light- weight construction of vehicle and key assemblies in every stage of the vehicle product development. Among vehicles ap- peared on the market and in research, it has presented continuously better performance. The paper describes application examples and successful experience of CAE simulation analysis and performance optimization during the lightweight de- sign and development of a self-developed model of Geely, and looks forward to the prospects for the development of lightweight of Geely vehicle.

  9. Making mundane pleasures visible: mediating daily likings with lightweight technology

    NARCIS (Netherlands)

    Kanis, M.; Brinkman, W.-P.

    2010-01-01

    This article discusses the sharing of daily pleasures with lightweight technology. Two mobile applications called PosiPost Me (Mobile internet edition) and PosiPost Be (Bluetooth edition) were developed to understand the potential of remote and proximity-based sharing of positive messages. These imp

  10. A Light-Weight Statically Scheduled Network-on-Chip

    DEFF Research Database (Denmark)

    Sørensen, Rasmus Bo; Schoeberl, Martin; Sparsø, Jens

    2012-01-01

    This paper investigates how a light-weight, statically scheduled network-on-chip (NoC) for real-time systems can be designed and implemented. The NoC provides communication channels between all cores with equal bandwidth and latency. The design is FPGA-friendly and consumes a minimum of resources...

  11. FY2013 Lightweight Materials R&D Annual Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2014-02-01

    As part of the U.S. Department of Energy’s (DOE’s) Vehicle Technologies Program (VTO), the Lightweight Materials (LM) activity focuses on the development and validation of advanced materials and manufacturing technologies to significantly reduce light and heavy duty vehicle weight without compromising other attributes such as safety, performance, recyclability, and cost.

  12. Watching the Birth of Super Star Clusters

    CERN Document Server

    Turner, J L; Turner, Jean L.; Beck, Sara C.

    2003-01-01

    Subarcsecond infrared and radio observations yield important information about the formation of super star clusters from their surrounding gas. We discuss the general properties of ionized and molecular gas near young, forming SSCs, as illustrated by the prototypical young forming super star cluster nebula in the dwarf galaxy, NGC 5253. This super star cluster appears to have a gravitationally bound nebula. The lack of molecular gas suggests a very high star formation efficiency, consistent with the formation of a large, bound star cluster.

  13. Two-Component Super AKNS Equations and Their Finite-Dimensional Integrable Super Hamiltonian System

    OpenAIRE

    Jing Yu; Jingwei Han

    2014-01-01

    Starting from a matrix Lie superalgebra, two-component super AKNS system is constructed. By making use of monononlinearization technique of Lax pairs, we find that the obtained two-component super AKNS system is a finite-dimensional integrable super Hamiltonian system. And its Lax representation and $r$ -matrix are also given in this paper.

  14. Two-Component Super AKNS Equations and Their Finite-Dimensional Integrable Super Hamiltonian System

    Directory of Open Access Journals (Sweden)

    Jing Yu

    2014-01-01

    Full Text Available Starting from a matrix Lie superalgebra, two-component super AKNS system is constructed. By making use of monononlinearization technique of Lax pairs, we find that the obtained two-component super AKNS system is a finite-dimensional integrable super Hamiltonian system. And its Lax representation and r-matrix are also given in this paper.

  15. Next-Generation MKIII Lightweight HUT/Hatch Assembly

    Science.gov (United States)

    McCarthy, Mike; Toscano, Ralph

    2013-01-01

    The MK III (H-1) carbon-graphite/ epoxy Hard Upper Torso (HUT)/Hatch assembly was designed, fabricated, and tested in the early 1990s. The spacesuit represented an 8.3 psi (˜58 kPa) technology demonstrator model of a zero prebreathe suit. The basic torso shell, brief, and hip areas of the suit were composed of a carbon-graphite/epoxy composite lay-up. In its current configuration, the suit weighs approximately 120 lb (˜54 kg). However, since future planetary suits will be designed to operate at 0.26 bar (˜26 kPa), it was felt that the suit's re-designed weight could be reduced to 79 lb (˜35 kg) with the incorporation of lightweight structural materials. Many robust, lightweight structures based on the technologies of advanced honeycomb materials, revolutionary new composite laminates, metal matrix composites, and recent breakthroughs in fullerene fillers and nanotechnology lend themselves well to applications requiring materials that are both light and strong. The major problem involves the reduction in weight of the HUT/ Hatch assembly for use in lunar and/or planetary applications, while at the same time maintaining a robust structural design. The technical objective is to research, design, and develop manufacturing methods that support fa b rica - tion of a lightweight HUT/Hatch assembly using advanced material and geometric redesign as necessary. Additionally, the lightweight HUT/Hatch assembly will interface directly with current MK III hardware. Using the new operating pressure and current MK III (H-1) interfaces as a starting block, it is planned to maximize HUT/Hatch assembly weight reduction through material selection and geometric redesign. A hard upper torso shell structure with rear-entry closure and corresponding hatch will be fabricated. The lightweight HUT/Hatch assembly will retrofit and interface with existing MK III (H-1) hardware elements, providing NASA with immediate "plug-andplay" capability. NASA crewmembers will have a lightweight

  16. Highlights from Super-Kamiokande

    Science.gov (United States)

    Okumura, Kimihiro

    2016-11-01

    Recent results from Super-Kamiokande experiment are reviewed in this paper; Neutrino mass hierarchy and CP violation in the lepton sector are investigated via νμ → νe oscillation of the atmospheric neutrinos. The event rate, correlation with solar activity, energy spectrum of the solar neutrinos are measured via electron elastic scattering interactions. Neutrino emission from the WIMP annihilation at the center of the Sun are searched in the GeV energy regions. New project, SK-Gd project, to enhance anti-neutrino identification capability, has been approved inside the collaboration group.

  17. Highlights from Super-Kamiokande

    Directory of Open Access Journals (Sweden)

    Okumura Kimihiro

    2016-01-01

    Full Text Available Recent results from Super-Kamiokande experiment are reviewed in this paper; Neutrino mass hierarchy and CP violation in the lepton sector are investigated via νμ → νe oscillation of the atmospheric neutrinos. The event rate, correlation with solar activity, energy spectrum of the solar neutrinos are measured via electron elastic scattering interactions. Neutrino emission from the WIMP annihilation at the center of the Sun are searched in the GeV energy regions. New project, SK-Gd project, to enhance anti-neutrino identification capability, has been approved inside the collaboration group.

  18. One-Loop Gauge Theory Amplitudes in N=4 Super Yang-Mills from MHV Vertices

    CERN Document Server

    Brandhuber, A; Travaglini, G; Brandhuber, Andreas; Spence, Bill; Travaglini, Gabriele

    2004-01-01

    We propose a new, twistor string theory inspired formalism to calculate loop amplitudes in N=4 super Yang-Mills theory. In this approach, maximal helicity violating (MHV) tree amplitudes of N=4 super Yang-Mills are used as vertices, using an off-shell prescription introduced by Cachazo, Svrcek and Witten, and combined into effective diagrams that incorporate large numbers of conventional Feynman diagrams. As an example, we apply this formalism to the particular class of MHV one-loop scattering amplitudes with an arbitrary number of external legs in N=4 super Yang-Mills. Remarkably, our approach naturally leads to a representation of the amplitudes as dispersion integrals, which we evaluate exactly. Our results for the MHV amplitudes are in precise agreement with the expressions for this class of amplitudes obtained previously by Bern, Dixon, Dunbar and Kosower using the cut-constructibility approach.

  19. External radiation surveillance

    Energy Technology Data Exchange (ETDEWEB)

    Antonio, E.J.

    1995-06-01

    This section of the 1994 Hanford Site Environmental Report describes how external radiation was measured, how surveys were performed, and the results of these measurements and surveys. External radiation exposure rates were measured at locations on and off the Hanford Site using thermoluminescent dosimeters (TLD). External radiation and contamination surveys were also performed with portable radiation survey instruments at locations on and around the Hanford Site.

  20. Lightweight autoclavable wide-angle contact lens for vitreous surgery.

    Science.gov (United States)

    Chalam, K V; Gupta, Shailesh K; Agarwal, Swati

    2007-01-01

    The authors describe an autoclavable, self-stabilizing, lightweight wide-angle contact lens for vitrectomy. The lens has two optical pieces with perforated plastic casing to sustain a high temperature (150 degrees C) for autoclaving. The lens has a 106 degrees static and 127 degrees dynamic field of view. The footplates and reduced weight (2.4 grams) due to the plastic casing allow self-stabilization of the lens. The open lens design.with high temperature resistant plastic prevents fogging during autoclaving and surgery. The autoclavable, self-stabilizing, lightweight wide-angle contact lens allows visualization of the peripheral retina during surgery and faster sterilization by autoclaving between surgeries without the disadvantage of lens fogging.

  1. Hot stamping advanced manufacturing technology of lightweight car body

    CERN Document Server

    Hu, Ping; He, Bin

    2017-01-01

    This book summarizes the advanced manufacturing technology of original innovations in hot stamping of lightweight car body. A detailed description of the technical system and basic knowledge of sheet metal forming is given, which helps readers quickly understand the relevant knowledge in the field. Emphasis has been placed on the independently developed hot stamping process and equipment, which help describe the theoretical and experimental research on key problems involving stress field, thermal field and phase transformation field in hot stamping process. Also, a description of the formability at elevated temperature and the numerical simulation algorithms for high strength steel hot stamping is given in combination with the experiments. Finally, the book presents some application cases of hot stamping technology such as the lightweight car body design using hot stamping components and gradient hardness components, and the cooling design of the stamping tool. This book is intended for researchers, engineers...

  2. Tendon-Actuated Lightweight In-Space MANipulator (TALISMAN)

    Science.gov (United States)

    Dorsey, John T.; Doggett, William R.; Komendera, Erik E.

    2015-01-01

    The robotic architecture of State-of-the-Art (SOA) space manipulators, represented by the Shuttle Remote Manipulator System (SRMS), inherently limits their capabilities to extend reach, reduce mass, apply force and package efficiently. TALISMAN uses a new and innovative robotic architecture that incorporates a combination of lightweight truss links, a novel hinge joint, tendon-articulation and passive tension stiffening to achieve revolutionary performance. A TALISMAN with performance similar to the SRMS has 1/10th of its mass and packages in 1/7th of its volume. The TALISMAN architecture allows its reach to be scaled over a large range; from 10 to over 300 meters. In addition, the dexterity (number of degrees-of-freedom) can be easily adjusted without significantly impacting manipulator mass because the joints are very lightweight.

  3. Experimental Validation of a Dynamic Model for Lightweight Robots

    Directory of Open Access Journals (Sweden)

    Alessandro Gasparetto

    2013-03-01

    Full Text Available Nowadays, one of the main topics in robotics research is dynamic performance improvement by means of a lightening of the overall system structure. The effective motion and control of these lightweight robotic systems occurs with the use of suitable motion planning and control process. In order to do so, model-based approaches can be adopted by exploiting accurate dynamic models that take into account the inertial and elastic terms that are usually neglected in a heavy rigid link configuration. In this paper, an effective method for modelling spatial lightweight industrial robots based on an Equivalent Rigid Link System approach is considered from an experimental validation perspective. A dynamic simulator implementing the formulation is used and an experimental test-bench is set-up. Experimental tests are carried out with a benchmark L-shape mechanism.

  4. BEHAVIOUR OF LIGHTWEIGHT CONCRETE CONTAINING PERIWINKLE SHELLS AT ELEVATED TEMPERATURE

    Directory of Open Access Journals (Sweden)

    F. FALADE

    2010-12-01

    Full Text Available This study presents the results of the investigation of the response of lightweight concrete to elevated temperature. Available literature indicates that research works have not been carried out in this area. The variables are: mix proportion, water/cement ratio, curing age and temperature. The parameters that were measured are: compressive strength, density and bond characteristics of the concrete matrix. The results showed that the compressive strength of concrete decreased with increase in water/cement ratio and temperature but increased with increase in curing age and cement content while the density decreased with increase in temperature. The bond between the concrete matrix also decreased as the temperature increased. Lightweight concrete containing periwinkle shells is only suitable for structures that will be subjected to temperature less than 300oC.

  5. MODULTEC - Modular technology for lightweight vehicles; MODULTEC - Modultechnologie fuer Leichtmobile

    Energy Technology Data Exchange (ETDEWEB)

    Horlacher, M.; Efler, T.; Wegmann, S.

    2003-07-01

    This final report for the Swiss Federal Office of Energy presents the results of two research projects (MODULTEC I and II) that were carried out between 1995 and 2002. The project's aims were to develop and assess components for light-weight car bodies, study and test novel reinforced plastic materials and to examine the industrial implementation of light-weight vehicles. The report presents details on prototype vehicles and transport systems, as well as crash tests. The development of compound plastics and appropriate adhesives is discussed as is the co-operation with various industrial partners. Various prototype components are described and other associated topics such as recycling, storage of alternative fuels and pedestrian protection issues are discussed.

  6. Cost-effective lightweight mirrors for aerospace and defense

    Science.gov (United States)

    Woodard, Kenneth S.; Comstock, Lovell E.; Wamboldt, Leonard; Roy, Brian P.

    2015-05-01

    The demand for high performance, lightweight mirrors was historically driven by aerospace and defense (A&D) but now we are also seeing similar requirements for commercial applications. These applications range from aerospace-like platforms such as small unmanned aircraft for agricultural, mineral and pollutant aerial mapping to an eye tracking gimbaled mirror for optometry offices. While aerospace and defense businesses can often justify the high cost of exotic, low density materials, commercial products rarely can. Also, to obtain high performance with low overall optical system weight, aspheric surfaces are often prescribed. This may drive the manufacturing process to diamond machining thus requiring the reflective side of the mirror to be a diamond machinable material. This paper summarizes the diamond machined finishing and coating of some high performance, lightweight designs using non-exotic substrates to achieve cost effective mirrors. The results indicate that these processes can meet typical aerospace and defense requirements but may also be competitive in some commercial applications.

  7. Tailored Buckling Microlattices as Reusable Light-Weight Shock Absorbers.

    Science.gov (United States)

    Frenzel, Tobias; Findeisen, Claudio; Kadic, Muamer; Gumbsch, Peter; Wegener, Martin

    2016-07-01

    Structures and materials absorbing mechanical (shock) energy commonly exploit either viscoelasticity or destructive modifications. Based on a class of uniaxial light-weight geometrically nonlinear mechanical microlattices and using buckling of inner elements, either a sequence of snap-ins followed by irreversible hysteretic - yet repeatable - self-recovery or multistability is achieved, enabling programmable behavior. Proof-of-principle experiments on three-dimensional polymer microstructures are presented.

  8. Lightweight Sandwich Panel in Cold Stores and Refrigerated Warehouses

    OpenAIRE

    Chidom, Charles

    2013-01-01

    The use of sandwich panels has gained considerable recognition in the construction industry and more use of this composite structure is ever increasing. This study highlights and familiarizes the use of lightweight sandwich panel in refrigerated warehouses and cold storage facility and construction and the challenges such construction faces in warm climates considering the effects of thermal load. The study was commissioned by HAMK Sheet Metal Center, the steel research and development ce...

  9. Ultra-lightweight mirror manufacturing and radiation response study

    Science.gov (United States)

    Fitzsimmons, T. C.; Crowe, D. A.

    1981-08-01

    The requirements for making ultra-lightweight mirrors of Ultra-Low Expansion (ULE) fused silica by frit bonding are investigated. A manufacturing assessment of the facilities needed to scale the mirror technology to 4 meters in diameter is included. A front surface flux loading thermal test of a.5M diameter frit bonded ULE mirror is also included. The test was supported by detailed modeling and analysis.

  10. Lightweight shape memory self-deployable structures for Gossamer applications

    Science.gov (United States)

    Sokolowski, Witold

    2004-01-01

    Currently, existing approaches for producing large, ultra-lightweight, deployable structures in space typically rely upon electro-mechanical mechanisms and mechanically expandable that are heavy, not stowage volume efficient, expensive and complex. Therefore, one of the major efforts at NASA and DoD has been to develop expandable structures characterized by low mass and small launch volume. As a result, space inflatable structures have emerged 9-10 years ago.

  11. Magnesium Technology and Manufacturing for Ultra Lightweight Armored Ground Vehicles

    Science.gov (United States)

    2009-02-01

    Bruce Davis and Rick DeLorme Magnesium Elektron North America, Inc. A reprint from the Proceedings of the 2008 Army Science Conference...SUPPLEMENTARY NOTES *Magnesium Elektron North America, Inc., 1001 College St., Madison, IL 62060 A reprint from the Proceedings of the 2008 Army Science...initial emphasis on the Elektron WE43 alloy system for lightweight armored ground vehicle applications. Engineering design factors are reviewed and

  12. Polymer Substrates For Lightweight, Thin-Film Solar Cells

    Science.gov (United States)

    Lewis, Carol R.

    1993-01-01

    Substrates survive high deposition temperatures. High-temperature-resistant polymers candidate materials for use as substrates of lightweight, flexible, radiation-resistant solar photovoltaic cells. According to proposal, thin films of copper indium diselenide or cadmium telluride deposited on substrates to serve as active semiconductor layers of cells, parts of photovoltaic power arrays having exceptionally high power-to-weight ratios. Flexibility of cells exploited to make arrays rolled up for storage.

  13. Light-weight cyptography for resource constrained environments

    Science.gov (United States)

    Baier, Patrick; Szu, Harold

    2006-04-01

    We give a survey of "light-weight" encryption algorithms designed to maximise security within tight resource constraints (limited memory, power consumption, processor speed, chip area, etc.) The target applications of such algorithms are RFIDs, smart cards, mobile phones, etc., which may store, process and transmit sensitive data, but at the same time do not always support conventional strong algorithms. A survey of existing algorithms is given and new proposal is introduced.

  14. Mechanical, Thermal and Functional Properties of Green Lightweight Foamcrete

    OpenAIRE

    Md Azree Othuman Mydin; Norizal Md Noordin

    2012-01-01

    In recent times, the construction industry has revealed noteworthy attention in the use of lightweight foamcrete as a building material due to its many favourable characteristics such as lighter weight, easy to fabricate, durable and cost effective. Foamcrete is a material consisting of Portland cement paste or cement filler matrix (mortar) with a homogeneous pore structure created by introducing air in the form of small bubbles. With a proper control in dosage of foam and m...

  15. Deployment of Lightweight Shock Mitigating Boat Manufacturing Innovation

    Science.gov (United States)

    2012-12-21

    VARTM Hull 1267 760 Deck 702 399 Console 540 350 Total 2509 1509 % Current 100% 60% % Savings - 40% Deployment of Lightweight Shock Mitigating...1430 47 Weight Evaluation- Baseline Boat Weights (lb) Segment Baseline 850 A 850 B 850 B-OM Fabrication Method Open Mold Open Mold VARTM Open...Segment Baseline 850 A 850 B 850 B-OM Fabrication Method Open Mold Open Mold VARTM Open Mold Hull 1115 843 717 789 Deck 665 587 481 529

  16. Characterization of porous acoustic materials applied to lightweight partition walls

    OpenAIRE

    Fangueiro, Raúl; Velosa, J. C.; Macieira, Mónica; Mendonça, Paulo

    2011-01-01

    The increased need to save material and energetic resources, allied with a growing concern on the environmental issues and incertitude on the evolution of the economy, has impelled minimalist-approaches to Architecture and Engineering, reducing to the minimum necessary expression the building elements. The development of new lightweight materials, most of them composites with fibrous reinforcement systems, has interest for building materials and textile industries. However, the...

  17. Analysis of Lightweight Materials for the AM2 System

    Science.gov (United States)

    2014-06-01

    crack propagation. Like most non- ferrous alloys , 6061-T6 alloy does not exhibit an endurance limit and failure can occur up to at least 109 cycles...materials that could replace the 6061-T6 aluminum alloy currently used in the AM2 airfield matting for the purpose of light-weighting the design. An in...operating conditions of the AM2. Newly developed extruded magnesium alloys were identified that could potentially provide weight savings of 30 to 40

  18. Optical trapping with Super-Gaussian beams

    CSIR Research Space (South Africa)

    McLaren, M

    2013-04-01

    Full Text Available We outline the possibility of optical trapping and tweezing with Super-Gaussian beam profiles. We show that the trapping strength can be tuned continuously by adjusting the order of a Super-Gaussian beam, approaching that of a perfect Gaussian...

  19. Tetrahedral Units: For Dodecahedral Super-Structures

    CERN Document Server

    Ortiz, Y; Liebman, J F

    2016-01-01

    Different novel organic-chemical possibilities for tetrahedral building units are considered, with attention to their utility in constructing different super-structures. As a representative construction we consider the use of sets of 20 such identical tetrahedral units to form a super-dodecahedron.

  20. Mechanical analysis of lightweight constructions manufactured with fused deposition modeling

    Science.gov (United States)

    Bagsik, A.; Josupeit, S.; Schoeppner, V.; Klemp, E.

    2014-05-01

    Additive production techniques have the advantage of manufacturing parts without needing a forming tool. One of the most used additive manufacturing processes is "Fused Deposition Modeling" (FDM) which allows the production of prototypes and end-use parts. Due to the manufacture layer by layer, also complex part geometries can be created in one working step. Furthermore, lightweight parts with specific inner core structures can be manufactured in order to achieve good weightrelated strength properties. In this paper the mechanical behavior of lightweight parts manufactured with the 3D production system Fortus 400mc from Stratasys and the material Polyetherimide (PEI) with the trade name Ultem*9085 is analyzed. The test specimens were built up with different inner structures and building directions. Therefore, test specimens with known lightweight core geometries (e.g. corrugated and honeycomb cores) were designed. A four-point bending test was conducted to analyze the strength properties as well as the weight-related strength properties. Additionally the influence of the structure width, the structure wall thickness and the top layer thickness was analyzed using a honeycomb structure.

  1. Vehicular hydrogen storage using lightweight tanks (regenerative fuel cell systems)

    Energy Technology Data Exchange (ETDEWEB)

    Mitlitsky, F; Myers, B; Weisberg, A H

    1999-06-01

    Energy storage systems with extremely high specific energy (>400 Wh/kg) have been designed that use lightweight tankage to contain the gases generated by reversible (unitized) regenerative fuel cells (URFCs). Lawrence Livermore National Laboratory (LLNL) will leverage work for aerospace applications supported by other sponsors (including BMDO, NASA, and USAF) to develop URFC systems for transportation and utility applications. Lightweight tankage is important for primary fuel cell powered vehicles that use on-board storage of hydrogen. Lightweight pressure vessels with state-of-the-art performance factors were designed, and prototypes are being fabricated to meet the DOE 2000 goals (4000 Wh/kg, 12% hydrogen by weight, 700 Wh/liter, and $20/kWh in high volume production). These pressure vessels use technologies that are easily adopted by industrial partners. Advanced liners provide permeation barriers for gas storage and are mandrels for composite overwrap. URFCs are important to the efficient use of hydrogen as a transportation fuel and enabler of renewable energy. H{sub 2}/halogen URFCs may be advantageous for stationary applications whereas H{sub 2}/O{sub 2} or H{sub 2}/air URFCs are advantageous for vehicular applications. URFC research and development is required to improve performance (efficiency), reduce catalyst loading, understand engineering operation, and integrate systems. LLNL has the experimental equipment and advanced URFC membrane electrode assemblies (some with reduced catalyst loading) for evaluating commercial hardware (not funded by DOE in FY1999).

  2. Ceramic/polymer functionally graded material (FGM) lightweight armor system

    Energy Technology Data Exchange (ETDEWEB)

    Petrovic, J.J.; McClellan, K.J.

    1998-12-31

    This is the final report of a two-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). Functionally graded material is an enabling technology for lightweight body armor improvements. The objective was to demonstrate the ability to produce functionally graded ceramic-polymer and ceramic-metal lightweight armor materials. This objective involved two aspects. The first and key aspect was the development of graded-porosity boron-carbide ceramic microstructures. The second aspect was the development of techniques for liquid infiltration of lightweight metals and polymers into the graded-porosity ceramic. The authors were successful in synthesizing boron-carbide ceramic microstructures with graded porosity. These graded-porosity boron-carbide hot-pressed pieces were then successfully liquid-infiltrated in vacuum with molten aluminum at 1,300 C, and with liquid polymers at room temperature. Thus, they were able to demonstrate the feasibility of producing boron carbide-aluminum and boron carbide-polymer functionally graded materials.

  3. Lightweight ZERODUR: Validation of Mirror Performance and Mirror Modeling Predictions

    Science.gov (United States)

    Hull, Tony; Stahl, H. Philip; Westerhoff, Thomas; Valente, Martin; Brooks, Thomas; Eng, Ron

    2017-01-01

    Upcoming spaceborne missions, both moderate and large in scale, require extreme dimensional stability while relying both upon established lightweight mirror materials, and also upon accurate modeling methods to predict performance under varying boundary conditions. We describe tests, recently performed at NASA's XRCF chambers and laboratories in Huntsville Alabama, during which a 1.2 m diameter, f/1.2988% lightweighted SCHOTT lightweighted ZERODUR(TradeMark) mirror was tested for thermal stability under static loads in steps down to 230K. Test results are compared to model predictions, based upon recently published data on ZERODUR(TradeMark). In addition to monitoring the mirror surface for thermal perturbations in XRCF Thermal Vacuum tests, static load gravity deformations have been measured and compared to model predictions. Also the Modal Response(dynamic disturbance) was measured and compared to model. We will discuss the fabrication approach and optomechanical design of the ZERODUR(TradeMark) mirror substrate by SCHOTT, its optical preparation for test by Arizona Optical Systems (AOS). Summarize the outcome of NASA's XRCF tests and model validations

  4. Ceramic/polymer functionally graded material (FGM) lightweight armor system

    Energy Technology Data Exchange (ETDEWEB)

    Petrovic, J.J.; McClellan, K.J.

    1998-12-31

    This is the final report of a two-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). Functionally graded material is an enabling technology for lightweight body armor improvements. The objective was to demonstrate the ability to produce functionally graded ceramic-polymer and ceramic-metal lightweight armor materials. This objective involved two aspects. The first and key aspect was the development of graded-porosity boron-carbide ceramic microstructures. The second aspect was the development of techniques for liquid infiltration of lightweight metals and polymers into the graded-porosity ceramic. The authors were successful in synthesizing boron-carbide ceramic microstructures with graded porosity. These graded-porosity boron-carbide hot-pressed pieces were then successfully liquid-infiltrated in vacuum with molten aluminum at 1,300 C, and with liquid polymers at room temperature. Thus, they were able to demonstrate the feasibility of producing boron carbide-aluminum and boron carbide-polymer functionally graded materials.

  5. Hummingbird: Ultra-Lightweight Cryptography for Resource-Constrained Devices

    Science.gov (United States)

    Engels, Daniel; Fan, Xinxin; Gong, Guang; Hu, Honggang; Smith, Eric M.

    Due to the tight cost and constrained resources of high-volume consumer devices such as RFID tags, smart cards and wireless sensor nodes, it is desirable to employ lightweight and specialized cryptographic primitives for many security applications. Motivated by the design of the well-known Enigma machine, we present a novel ultra-lightweight cryptographic algorithm, referred to as Hummingbird, for resource-constrained devices in this paper. Hummingbird can provide the designed security with small block size and is resistant to the most common attacks such as linear and differential cryptanalysis. Furthermore, we also present efficient software implementation of Hummingbird on the 8-bit microcontroller ATmega128L from Atmel and the 16-bit microcontroller MSP430 from Texas Instruments, respectively. Our experimental results show that after a system initialization phase Hummingbird can achieve up to 147 and 4.7 times faster throughput for a size-optimized and a speed-optimized implementations, respectively, when compared to the state-of-the-art ultra-lightweight block cipher PRESENT[10] on the similar platforms.

  6. Mechanical Properties of Fiber Reinforced Lightweight Concrete Containing Surfactant

    Directory of Open Access Journals (Sweden)

    Yoo-Jae Kim

    2010-01-01

    Full Text Available Fiber reinforced aerated lightweight concrete (FALC was developed to reduce concrete's density and to improve its fire resistance, thermal conductivity, and energy absorption. Compression tests were performed to determine basic properties of FALC. The primary independent variables were the types and volume fraction of fibers, and the amount of air in the concrete. Polypropylene and carbon fibers were investigated at 0, 1, 2, 3, and 4% volume ratios. The lightweight aggregate used was made of expanded clay. A self-compaction agent was used to reduce the water-cement ratio and keep good workability. A surfactant was also added to introduce air into the concrete. This study provides basic information regarding the mechanical properties of FALC and compares FALC with fiber reinforced lightweight concrete. The properties investigated include the unit weight, uniaxial compressive strength, modulus of elasticity, and toughness index. Based on the properties, a stress-strain prediction model was proposed. It was demonstrated that the proposed model accurately predicts the stress-strain behavior of FALC.

  7. Ending Aging in Super Glassy Polymer Membranes

    Energy Technology Data Exchange (ETDEWEB)

    Lau, CH; Nguyen, PT; Hill, MR; Thornton, AW; Konstas, K; Doherty, CM; Mulder, RJ; Bourgeois, L; Liu, ACY; Sprouster, DJ; Sullivan, JP; Bastow, TJ; Hill, AJ; Gin, DL; Noble, RD

    2014-04-16

    Aging in super glassy polymers such as poly(trimethylsilylpropyne) (PTMSP), poly(4-methyl-2-pentyne) (PMP), and polymers with intrinsic microporosity (PIM-1) reduces gas permeabilities and limits their application as gas-separation membranes. While super glassy polymers are initially very porous, and ultra-permeable, they quickly pack into a denser phase becoming less porous and permeable. This age-old problem has been solved by adding an ultraporous additive that maintains the low density, porous, initial stage of super glassy polymers through absorbing a portion of the polymer chains within its pores thereby holding the chains in their open position. This result is the first time that aging in super glassy polymers is inhibited whilst maintaining enhanced CO2 permeability for one year and improving CO2/N-2 selectivity. This approach could allow super glassy polymers to be revisited for commercial application in gas separations.

  8. Do we expect to find the Super-Earths close to the gas giants?

    CERN Document Server

    Podlewska, E

    2009-01-01

    We have investigated the evolution of a pair of interacting planets embedded in a gaseous disc, considering the possibility of the resonant capture of a Super-Earth by a Jupiter mass gas giant. First, we have examined the situation where the Super-Earth is on the internal orbit and the gas giant on the external one. It has been found that the terrestrial planet is scattered from the disc or the gas giant captures the Super-Earth into an interior 3:2 or 4:3 mean-motion resonance. The stability of the latter configurations depends on the initial planet positions and on eccentricity evolution. The behaviour of the system is different if the Super-Earth is the external planet. We have found that instead of being captured in the mean-motion resonance, the terrestrial planet is trapped at the outer edge of the gap opened by the gas giant. This effect prevents the occurrence of the first order mean-motion commensurability. These results are particularly interesting in light of recent exoplanet discoveries and provid...

  9. Group-based single image super-resolution with online dictionary learning

    Science.gov (United States)

    Lu, Xuan; Wang, Dingwen; Shi, Wenxuan; Deng, Dexiang

    2016-12-01

    Recently, sparse representation has been successfully used in single image super-resolution reconstruction. Unlike the traditional single image super-resolution methods such as image interpolation, the super-resolution with sparse representation reconstructs image with one or several constant dictionaries learned from external databases. However, the contents can vary significantly across different patches in a single image, and the fixed dictionaries cannot suit for every patch. This paper presents a novel approach for single image super-resolution based on sparse representation, which uses group as the basic unit, and trains dictionary with external database and the input low-resolution image itself for each group to ensure that the dictionary is suitable for the patches in the group. Simultaneous sparse coding algorithm is used to accelerate the processing and improve the result. Extensive experiments on natural images show that our method achieves better results than some state-of-the-art algorithms in terms of both objective and human visual evaluations.

  10. Thermal design of the Space Shuttle External Tank

    Science.gov (United States)

    Warmbrod, J. D.; Vaniman, J. L.; Elam, B. F.

    1981-01-01

    The history of the engineering and manufacturing requirements leading to the final Thermal Protection System (TPS) for the External Tank (ET) is presented. The thermal design for the ET must be optimized, based on considerations of cost, weight, and application of the TPS. The significant thermal requirements include the structural and component temperature limits, the propellant quality, the minimization of ice and frost, no air liquefaction, and no film boiling. The TPS materials selected to meet the requirements are a low density closed cell foam (CPR-488) and two light-weight ablators (SLA-56 and MA-25s). The first four flights of the Space Shuttle (1981) will measure and evaluate external environmental, structural, propulsion, electrical, and engine performance data. The ET will be instrumented to measure acoustics, pressures, heat transfer, vibration, temperatures, and structural strains. TPS weight reductions are planned for future ETs through the use of a comprehensive thermal instrumentation system.

  11. Research overview of design method of super light multi-hole class- honeycomb sandwich structure materials

    Directory of Open Access Journals (Sweden)

    Xiang LI

    Full Text Available With the sandwich structure materials' application and promotion in the field of engineering continuously, existing sandwich structure material gradually cannot meet the design requirements. It is very urgent to develop new sandwich structure materials of high efficiency, energy saving and easy to process. The project puts forward and constructs a new kind of class-honeycomb sandwich structure material combined with important application backgrounds that super light and high strength metal sandwich structure materials are applied into the high weight and high energy consumption equipments of automobile, aerospace and machinery and so on. This research involve: mechanical properties equivalent method for the class-honeycomb sandwich structure and its core; Strength, stiffness and inherent frequency characteristic and failure criterions of the class-honeycomb sandwich structure; based on the failure criterions constructing the multiple-constraint models of the class-honeycomb sandwich structure. The research tries to put forward a new method for innovative design of lightweight material and structure and new ideas of lightweight technology research in theory and practice.

  12. Brittleness Generation Mechanism and Failure Model of High Strength Lightweight Aggregate Concrete

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The brittleness generation mechanism of high strength lightweight aggregate concrete(HSLWAC) was presented, and it was indicated that lightweight aggregate was the vulnerable spot,initiating brittleness. Based on the analysis of the brittleness failure by the load-deflection curve, the brittleness presented by HSLWAC was more prominent compared with ordinary lightweight aggregate concrete of the same strength grade. The model of brittleness failure was also established.

  13. Externally Verifiable Oblivious RAM

    Directory of Open Access Journals (Sweden)

    Gancher Joshua

    2017-04-01

    Full Text Available We present the idea of externally verifiable oblivious RAM (ORAM. Our goal is to allow a client and server carrying out an ORAM protocol to have disputes adjudicated by a third party, allowing for the enforcement of penalties against an unreliable or malicious server. We give a security definition that guarantees protection not only against a malicious server but also against a client making false accusations. We then give modifications of the Path ORAM [15] and Ring ORAM [9] protocols that meet this security definition. These protocols both have the same asymptotic runtimes as the semi-honest original versions and require the external verifier to be involved only when the client or server deviates from the protocol. Finally, we implement externally verified ORAM, along with an automated cryptocurrency contract to use as the external verifier.

  14. External Beam Therapy (EBT)

    Science.gov (United States)

    ... Esophageal Cancer Treatment Head and Neck Cancer Treatment Lung Cancer Treatment Prostate Cancer Treatment Brain Tumor Treatment Why is ... Radiation Oncology) Breast Cancer Treatment Esophageal Cancer Treatment Lung Cancer Treatment Images related to External Beam Therapy (EBT) Sponsored ...

  15. MALIGNANT EXTERNAL OTITIS

    OpenAIRE

    Massoud Moghaddam

    1993-01-01

    Two case reports of malignant external otitis in the elderly diabetics and their complications and management with regard to our experience at Amir Alam Hospital, Department of ENT will be discussed here.

  16. Checklists for external validity

    DEFF Research Database (Denmark)

    Dyrvig, Anne-Kirstine; Kidholm, Kristian; Gerke, Oke;

    2014-01-01

    RATIONALE, AIMS AND OBJECTIVES: The quality of the current literature on external validity varies considerably. An improved checklist with validated items on external validity would aid decision-makers in judging similarities among circumstances when transferring evidence from a study setting...... to an implementation setting. In this paper, currently available checklists on external validity are identified, assessed and used as a basis for proposing a new improved instrument. METHOD: A systematic literature review was carried out in Pubmed, Embase and Cinahl on English-language papers without time restrictions....... The retrieved checklist items were assessed for (i) the methodology used in primary literature, justifying inclusion of each item; and (ii) the number of times each item appeared in checklists. RESULTS: Fifteen papers were identified, presenting a total of 21 checklists for external validity, yielding a total...

  17. SuperB Progress Report for Physics

    Energy Technology Data Exchange (ETDEWEB)

    O' Leary, B.; /Aachen, Tech. Hochsch.; Matias, J.; Ramon, M.; /Barcelona, IFAE; Pous, E.; /Barcelona U.; De Fazio, F.; Palano, A.; /INFN, Bari; Eigen, G.; /Bergen U.; Asgeirsson, D.; /British Columbia U.; Cheng, C.H.; Chivukula, A.; Echenard, B.; Hitlin, D.G.; Porter, F.; Rakitin, A.; /Caltech; Heinemeyer, S.; /Cantabria Inst. of Phys.; McElrath, B.; /CERN; Andreassen, R.; Meadows, B.; Sokoloff, M.; /Cincinnati U.; Blanke, M.; /Cornell U., Phys. Dept.; Lesiak, T.; /Cracow, INP /DESY /Zurich, ETH /INFN, Ferrara /Frascati /INFN, Genoa /Glasgow U. /Indiana U. /Mainz U., Inst. Phys. /Karlsruhe, Inst. Technol. /KEK, Tsukuba /LBL, Berkeley /UC, Berkeley /Lisbon, IST /Ljubljana U. /Madrid, Autonoma U. /Maryland U. /MIT /INFN, Milan /McGill U. /Munich, Tech. U. /Notre Dame U. /PNL, Richland /INFN, Padua /Paris U., VI-VII /Orsay, LAL /Orsay, LPT /INFN, Pavia /INFN, Perugia /INFN, Pisa /Queen Mary, U. of London /Regensburg U. /Republica U., Montevideo /Frascati /INFN, Rome /INFN, Rome /INFN, Rome /Rutherford /Sassari U. /Siegen U. /SLAC /Southern Methodist U. /Tel Aviv U. /Tohoku U. /INFN, Turin /INFN, Trieste /Uppsala U. /Valencia U., IFIC /Victoria U. /Wayne State U. /Wisconsin U., Madison

    2012-02-14

    SuperB is a high luminosity e{sup +}e{sup -} collider that will be able to indirectly probe new physics at energy scales far beyond the reach of any man made accelerator planned or in existence. Just as detailed understanding of the Standard Model of particle physics was developed from stringent constraints imposed by flavour changing processes between quarks, the detailed structure of any new physics is severely constrained by flavour processes. In order to elucidate this structure it is necessary to perform a number of complementary studies of a set of golden channels. With these measurements in hand, the pattern of deviations from the Standard Model behavior can be used as a test of the structure of new physics. If new physics is found at the LHC, then the many golden measurements from SuperB will help decode the subtle nature of the new physics. However if no new particles are found at the LHC, SuperB will be able to search for new physics at energy scales up to 10-100 TeV. In either scenario, flavour physics measurements that can be made at SuperB play a pivotal role in understanding the nature of physics beyond the Standard Model. Examples for using the interplay between measurements to discriminate New Physics models are discussed in this document. SuperB is a Super Flavour Factory, in addition to studying large samples of B{sub u,d,s}, D and {tau} decays, SuperB has a broad physics programme that includes spectroscopy both in terms of the Standard Model and exotica, and precision measurements of sin{sup 2} {theta}{sub W}. In addition to performing CP violation measurements at the {Upsilon}(4S) and {phi}(3770), SuperB will test CPT in these systems, and lepton universality in a number of different processes. The multitude of rare decay measurements possible at SuperB can be used to constrain scenarios of physics beyond the Standard Model. In terms of other precision tests of the Standard Model, this experiment will be able to perform precision over

  18. The superB silicon vertex tracker

    Energy Technology Data Exchange (ETDEWEB)

    Rizzo, G., E-mail: giuliana.rizzo@pi.infn.i [INFN-Pisa and Universita di Pisa (Italy); Avanzini, C.; Batignani, G.; Bettarini, S.; Bosi, F.; Calderini, G.; Ceccanti, M.; Cenci, R.; Cervelli, A.; Crescioli, F.; Dell' Orso, M.; Forti, F.; Giannetti, P.; Giorgi, M.A. [INFN-Pisa and Universita di Pisa (Italy); Lusiani, A. [Scuola Normale Superiore and INFN-Pisa (Italy); Gregucci, S.; Mammini, P.; Marchiori, G.; Massa, M.; Morsani, F. [INFN-Pisa and Universita di Pisa (Italy)

    2010-05-21

    The SuperB asymmetric e{sup +}-e{sup -} collider has been designed to deliver a luminosity greater than 10{sup 36}cm{sup -2}s{sup -1} with moderate beam currents. Comparing to current B-Factories, the reduced center of mass boost of the SuperB machine requires improved vertex resolution to allow precision measurements sensitive to New Physics. We present the conceptual design of the silicon vertex tracker (SVT) for the SuperB detector with the present status of the R and D on the different options under study for its innermost Layer0.

  19. Migration with fiscal externalities.

    Science.gov (United States)

    Hercowitz, Z; Pines, D

    1991-11-01

    "This paper analyses the distribution of a country's population among regions when migration involves fiscal externalities. The main question addressed is whether a decentralized decision making [by] regional governments can produce an optimal population distribution...or a centralized intervention is indispensable, as argued before in the literature.... It turns out that, while with costless mobility the fiscal externality is fully internalized by voluntary interregional transfers, with costly mobility, centrally coordinated transfers still remain indispensable for achieving the socially optimal allocation."

  20. Sen cycles and externalities

    OpenAIRE

    Piggins, Ashley; Salerno, Gillian

    2016-01-01

    It has long been understood that externalities of some kind are responsible for Sen’s (1970) theorem on the impossibility of a Paretian liberal. However, Saari and Petron (2006) show that for any social preference cycle generated by combining the weak Pareto principle and individual decisiveness, every decisive individual must suffer at least one strong negative externality. We show that this fundamental result only holds when individual preferences are strict. Building on their contribution,...

  1. Cryogenic Piezo Actuators for Lightweight, Large Aperture, Deployable Membrane Mirrors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Single crystal piezoelectric actuators are proposed to enable large stroke, high precision, shape control for cryogenic lightweight deployable membrane mirror...

  2. Method for calculating thermal properties of lightweight floor heating panels based on an experimental setup

    DEFF Research Database (Denmark)

    Weitzmann, Peter; Svendsen, Svend

    2005-01-01

    Lightweight floor heating systems consist of a plastic tube connected to a heat distribution aluminium plate and are used in wooden floor constructions. The thermal properties of lightweight floor heating systems cannot be described accurately. The reason is a very complex interaction of convection......, radiation and conduction of the heat transfer between pipe and surrounding materials. The European Standard for floor heating, EN1264, does not cover lightweight systems, while the supplemental Nordtest Method VVS127 is aimed at lightweight systems. The thermal properties can be found using tabulated values...

  3. N=2 Super - $W_{3}$ Algebra and N=2 Super Boussinesq Equations

    CERN Document Server

    Ivanov, E; Malik, R P

    1995-01-01

    We study classical $N=2$ super-$W_3$ algebra and its interplay with $N=2$ supersymmetric extensions of the Boussinesq equation in the framework of the nonlinear realization method and the inverse Higgs - covariant reduction approach. These techniques have been previously applied by us in the bosonic $W_3$ case to give a new geometric interpretation of the Boussinesq hierarchy. Here we deduce the most general $N=2$ super Boussinesq equation and two kinds of the modified $N=2$ super Boussinesq equations, as well as the super Miura maps relating these systems to each other, by applying the covariant reduction to certain coset manifolds of linear $N=2$ super-$W_3^{\\infty}$ symmetry associated with $N=2$ super-$W_3$. We discuss the integrability properties of the equations obtained and their correspondence with the formulation based on the notion of the second hamiltonian structure.

  4. Modified super twisting controller for servicing to uncontrolled spacecraft

    Institute of Scientific and Technical Information of China (English)

    Binglong Chen; Yunhai Geng

    2015-01-01

    A relative position and attitude coupled sliding mode control er is proposed by combining the standard super twisting (ST) control and basic linear algorithm for autonomous rendezvous and docking. It is schemed for on-orbit servicing to a tumbling non-cooperative target spacecraft subjected to external disturbances. A coupled dynamic model is established including both kinemati-cal and dynamic coupled effect of relative rotation on relative translation, which il ustrates the relative movement between the docking port located in target spacecraft and another in service spacecraft. The modified super twisting (MST) control algorithm containing linear compensation items is schemed to manipulate the relative position and attitude synchronously. The correction provides more robustness and convergence velocity for dealing with linearly growing perturbations than the ST control algorithm. Moreover, the stability characteristic of closed-loop system is ana-lyzed by Lyapunov method. Numerical simulations are adopted to verify the analysis with the comparison between MST and ST control algorithms. Simulation results demonstrate that the pro-posed MST control er is characterized by high precision, strong robustness and fast convergence velocity to attenuate the linearly increasing perturbations.

  5. Eyeglass Large Aperture, Lightweight Space Optics FY2000 - FY2002 LDRD Strategic Initiative

    Energy Technology Data Exchange (ETDEWEB)

    Hyde, R

    2003-02-10

    differences in their requirements and implementations, the fundamental difficulty in utilizing large aperture optics is the same for all of these applications: It is extremely difficult to design large aperture space optics which are both optically precise and can meet the practical requirements for launch and deployment in space. At LLNL we have developed a new concept (Eyeglass) which uses large diffractive optics to solve both of these difficulties; greatly reducing both the mass and the tolerance requirements for large aperture optics. During previous LDRD-supported research, we developed this concept, built and tested broadband diffractive telescopes, and built 50 cm aperture diffraction-limited diffractive lenses (the largest in the world). This work is fully described in UCRL-ID-136262, Eyeglass: A Large Aperture Space Telescope. However, there is a large gap between optical proof-of-principle with sub-meter apertures, and actual 50 meter space telescopes. This gap is far too large (both in financial resources and in spacecraft expertise) to be filled internally at LLNL; implementation of large aperture diffractive space telescopes must be done externally using non-LLNL resources and expertise. While LLNL will never become the primary contractor and integrator for large space optical systems, our natural role is to enable these devices by developing the capability of producing very large diffractive optics. Accordingly, the purpose of the Large Aperture, Lightweight Space Optics Strategic Initiative was to develop the technology to fabricate large, lightweight diffractive lenses. The additional purpose of this Strategic Initiative was, of course, to demonstrate this lens-fabrication capability in a fashion compellingly enough to attract the external support necessary to continue along the path to full-scale space-based telescopes. During this 3 year effort (FY2000-FY2002) we have developed the capability of optically smoothing and diffractively-patterning thin meter

  6. Large Lightweight Mirrors Controlled by Dielectric Elastomer Artifical Muscle

    Science.gov (United States)

    Kornbluh, R. D.; Flamm, D. S.; Vujkovic-Civijin, P.; Pelrine, R. E.; Huestis, D. L.

    2002-05-01

    We will describe a new concept for control of the lightweight large-aperture mirrors that will be required for future space-based astronomy and remote sensing applications. To be cost effective and practical, such optical systems must be lightweight and capable of deployment from highly compacted stowed configurations. Optical systems based on membrane mirrors or other lightweight structures can address some of these needs, but such flexible gossamer structures present challenges in achieving and maintaining the required shape or figure. For the past 9 years SRI has been exploring dielectric elastomer artifical muscle technology for active control of objects and structures [1-2]. The basic functional element is a thin polymer film coated on both sides by a compliant electrode material. When voltage is applied between the top and bottom electrodes, an electrostrictive compressive force squeezes the film, causing it to expand in area. The induced forces are related to the square of the voltage. If we assemble a large mirror from numerous independently addressable elements, sophisticated control is possible, even including adaptive optics. Dielectric elastomers have many advantages over other electroactive polymers and other smart-materials actuation technologies that have been considered in the past. For example, from many candidate materials we can choose ones with high planar strains, low power dissipation, tolerance of the space environment, and ease of commercial fabrication into large sheets. [1] R. Pelrine, R. Kornbluh, Q. Pei, and J. Joseph, Science 287, 386 (2000). [2] R. Pelrine, P. Sommer-Larson, R. Kornbluh, R. Heydt, G. Kofod, Q. Pei, and P. Gravesen, in Smart Structures and Materials 2001: Electroactive Polymer Actuators and Devices, ed. Y. Bar-Cohen, Proc. SPIE 4329, 335 (2001).

  7. High precision optical finishing of lightweight silicon carbide aspheric mirror

    Science.gov (United States)

    Kong, John; Young, Kevin

    2010-10-01

    Critical to the deployment of large surveillance optics into the space environment is the generation of high quality optics. Traditionally, aluminum, glass and beryllium have been used; however, silicon carbide becomes of increasing interest and availability due to its high strength. With the hardness of silicon carbide being similar to diamond, traditional polishing methods suffer from slow material removal rates, difficulty in achieving the desired figure and inherent risk of causing catastrophic damage to the lightweight structure. Rather than increasing structural capacity and mass of the substrate, our proprietary sub-aperture aspheric surface forming technology offers higher material removal rates (comparable to that of Zerodur or Fused Silica), a deterministic approach to achieving the desired figure while minimizing contact area and the resulting load on the optical structure. The technology performed on computer-controlled machines with motion control software providing precise and quick convergence of surface figure, as demonstrated by optically finishing lightweight silicon carbide aspheres. At the same time, it also offers the advantage of ideal pitch finish of low surface micro-roughness and low mid-spatial frequency error. This method provides a solution applicable to all common silicon carbide substrate materials, including substrates with CVD silicon carbide cladding, offered by major silicon carbide material suppliers. This paper discusses a demonstration mirror we polished using this novel technology. The mirror is a lightweight silicon carbide substrate with CVD silicon carbide cladding. It is a convex hyperbolic secondary mirror with 104mm diameter and approximately 20 microns aspheric departure from best-fit sphere. The mirror has been finished with surface irregularity of better than 1/50 wave RMS @632.8 nm and surface micro-roughness of under 2 angstroms RMS. The technology has the potential to be scaled up for manufacturing capabilities of

  8. A lightweight feedback-controlled microdrive for chronic neural recordings

    Science.gov (United States)

    Jovalekic, A.; Cavé-Lopez, S.; Canopoli, A.; Ondracek, J. M.; Nager, A.; Vyssotski, A. L.; Hahnloser, R. H. R.

    2017-04-01

    Objective. Chronic neural recordings have provided many insights into the relationship between neural activity and behavior. We set out to develop a miniaturized motorized microdrive that allows precise electrode positioning despite possibly unreliable motors. Approach. We designed a feedback-based motor control mechanism. It contains an integrated position readout from an array of magnets and a Hall sensor. Main results. Our extremely lightweight (feedback-based microdrive control requires little extra size and weight, suggesting that such control can be incorporated into more complex multi-electrode designs.

  9. Cryogenic optical tests of a lightweight HIP beryllium mirror

    Science.gov (United States)

    Melugin, Ramsey K.; Miller, Jacob H.; Young, J. A.; Howard, Steven D.; Pryor, G. Mark

    Five interferometric tests were conducted at cryogenic temperatures on a lightweight, 50 cm diameter, hot isostatic pressed (HIP) beryllium mirror in the Ames Research Center (ARC) Cryogenic Optics Test Facility. The purpose of the tests was to determine the stability of the mirror's figure when cooled to cryogenic temperatures. Test temperatures ranged from room ambient to 8 K. One cycle to 8 K and five cycles to 80 K were performed. Optical and thermal test methods are described. Data is presented to show the amount of cryogenic distortion and hysteresis present in the mirror when measured with an earlier, Shack interferometer, and with a newly-acquired, phase-measuring interferometer.

  10. Lightweight Aggregate Concrete. The materials in the precast elements

    DEFF Research Database (Denmark)

    Goltermann, Per; Larsen, Henning; Ingholt, N.U.

    1996-01-01

    The precast lightweight aggregate concrete (LAC) elements are used extensively in Denmark, where the use of precast elements domonates the building structures. Similar elements are used in other parts of Nothern Europe, which have lead to development of an European standard for precast LAC elements...... of LAC with open structure (prEN1520).The test results have shown that the formulas in prEN1520's revision are fairly correct and lead to slightly conservative estimates of the modulus of elasticity and flexural strength....

  11. Lightweight rotor design by optimal spar cap offset

    Science.gov (United States)

    Croce, A.; Sartori, L.; Lunghini, M. S.; Clozza, L.; Bortolotti, P.; Bottasso, C. L.

    2016-09-01

    Bend-twist coupling behavior is induced in a blade by displacing the suction side spar cap towards the leading edge, and the pressure side one in the opposite direction. Additional couplings are introduced by rotating the spar cap fibers. The structural configuration of the blade is optimized using an automated design environment. The resulting blade shows significant benefits in terms of mass and loads when compared to the baseline uncoupled one. Finally, the lightweight design concept is used to increase the rotor size, resulting in a larger energy yield for the same hub loads.

  12. Laser based metal and plastics joining for lightweight design

    Science.gov (United States)

    Kahmann, Max; Quentin, Ulf; Kirchhoff, Marc; Brockmann, Rüdiger; Löffler, Klaus

    2015-03-01

    One of the most important issues in automotive industry is lightweight design, especially since the CO2 emission of new cars has to be reduced by 2020. Plastic and fiber reinforced plastics (e.g. CFRP and GFRP) receive besides new manufacturing methods and the employment of high-strength steels or non-ferrous metals increasing interest. Especially the combination of different materials such as metals and plastics to single components exhausts the entire potential on weight reduction. This article presents an approach based on short laser pulses to join such dissimilar materials in industrial applications.

  13. Light-weight spherical mirrors for Cherenkov detectors

    CERN Document Server

    Cisbani, E; Colilli, S; Crateri, R; Cusanno, F; De Leo, R; Fratoni, R; Frullani, S; Garibaldi, F; Giuliani, F; Gricia, M; Iodice, M; Iommi, R; Lagamba, L; Lucentini, M; Mostarda, A; Nappi, E; Pierangeli, L; Santavenere, F; Urciuoli, G M; Vernin, P

    2003-01-01

    Light-weight spherical mirrors have been appositely designed and built for the gas threshold Cherenkov detectors of the two Hall A spectrometers. The mirrors are made of a 1 mm thick aluminized plexiglass sheet, reinforced by a rigid backing consisting of a phenolic honeycomb sandwiched between two carbon fiber mats epoxy glued. The produced mirrors have a thickness equivalent to 0.55% of radiation length, and an optical slope error of about 5.5 mrad. These characteristics make these mirrors suitable for the implementation in Cherenkov threshold detectors. Ways to improve the mirror features are also discussed in view of their possible employment in RICH detectors.

  14. Vibrations in a Multi-Storey Lightweight Building Structure

    DEFF Research Database (Denmark)

    Andersen, Lars Vabbersgaard; Kirkegaard, Poul Henning

    2013-01-01

    This paper provides a quantification of the changes in vibration level that can be expected in a lightweight multi-storey wooden building due to reduced connection stiffness or added nonstructural mass. Firstly, the impact of changes in the floor-to-wall connections is examined. Secondly, a study...... is performed regarding variations of the vibration level due to different placements of nonstructural mass inside the building. The analyses are carried out by means of a modular three-dimensional finite-element model. Each floor and wall panel is modelled in high detail, including door and window openings...

  15. Lightweight Radioisotope Heater Unit (LWRHU) production for the Cassini mission

    Energy Technology Data Exchange (ETDEWEB)

    Rinehart, G.H.

    1996-06-01

    The Lightweight Radioisotope Heater Unit (LWRHU) is a {sup 238}PuO{sub 2} fueled heat source designed to provide a thermal watt of power for space missions. The LWRHU will be used to maintain the temperature of various components on the spacecraft at the required level. The heat source consists of a {sup 238}PuO{sub 2} fuel pellet, a Pt-30Rh capsule, a pyrolytic graphite insulator, and a woven graphite aeroshell assembly. Los Alamos has fabricated 180 heater units, which will be used on the Cassini mission. This report summarizes the specifications, fabrication processes, and production data for the heat sources fabricated at Los Alamos.

  16. An extremely lightweight fingernail worn prosthetic interface device

    Science.gov (United States)

    Yetkin, Oguz; Ahluwalia, Simranjit; Silva, Dinithi; Kasi-Okonye, Isioma; Volker, Rachael; Baptist, Joshua R.; Popa, Dan O.

    2016-05-01

    Upper limb prosthetics are currently operated using several electromyography sensors mounted on an amputee's residual limb. In order for any prosthetic driving interface to be widely adopted, it needs to be responsive, lightweight, and out of the way when not being used. In this paper we discuss the possibility of replacing such electrodes with fingernail optical sensor systems mounted on the sound limb. We present a prototype device that can detect pinch gestures and communicate with the prosthetic system. The device detects the relative position of fingers to each other by measuring light transmitted via tissue. Applications are not limited to prosthetic control, but can be extended to other human-machine interfaces.

  17. Minimization of structure-borne noise in lightweight buildings

    DEFF Research Database (Denmark)

    Niu, Bin; Olhoff, Niels

    2012-01-01

    This paper deals with the problem of minimizing the structure-borne noise induced in a room by machinery vibration. A generalized system consisting of the machine, the base plate, resilient mounts, the floor plate and the room cavity is developed for analysis and optimization. Topological design...... of the base plate is studied for optimizing machinery installation. Furthermore, periodic mounts are optimized for the noise reduction. Finally, a modular model of a lightweight building is developed for design optimization of dimensions and connections of modules in the building for decreasing machinery...

  18. Model Reduction in Dynamic Finite Element Analysis of Lightweight Structures

    DEFF Research Database (Denmark)

    Flodén, Ola; Persson, Kent; Sjöström, Anders

    2012-01-01

    The application of wood as a construction material when building multi-storey buildings has many advantages, e.g., light weight, sustainability and low energy consumption during the construction and lifecycle of the building. However, compared to heavy structures, it is a greater challenge to build...... lightweight structures without noise and disturbing vibrations between storeys and rooms. The dynamic response of floor and wall structures may be investigated using finite element models with three-dimensional solid elements [1]. In order to analyse the global response of complete buildings, finite element...

  19. Accuracy of Dynamic and Acoustic Analysis of Lightweight Panel Structures

    DEFF Research Database (Denmark)

    Kirkegaard, Poul Henning; Dickow, Kristoffer Ahrens; Andersen, Lars Vabbersgaard

    2012-01-01

    in such buildings is important. In the lowfrequency range, prediction of sound and vibration in building structures may be achieved by finite-element analysis (FEA). The aim of this paper is to compare the two commercial codes ABAQUS and ANSYS for FEA of an acoustic-structural coupling in a timber lightweight panel...... structure. For this purpose, modal analyses are carried out employing a fully coupled model of sound waves within an acoustic medium and vibrations in the structural part. The study concerns the frequency range 50–250 Hz....

  20. Lightweight approach to model traceability in a CASE tool

    Science.gov (United States)

    Vileiniskis, Tomas; Skersys, Tomas; Pavalkis, Saulius; Butleris, Rimantas; Butkiene, Rita

    2017-07-01

    A term "model-driven" is not at all a new buzzword within the ranks of system development community. Nevertheless, the ever increasing complexity of model-driven approaches keeps fueling all kinds of discussions around this paradigm and pushes researchers forward to research and develop new and more effective ways to system development. With the increasing complexity, model traceability, and model management as a whole, becomes indispensable activities of model-driven system development process. The main goal of this paper is to present a conceptual design and implementation of a practical lightweight approach to model traceability in a CASE tool.

  1. Lightweight, Efficient Power Converters for Advanced Turboelectric Aircraft Propulsion Systems

    Science.gov (United States)

    Hennessy, Michael J.

    2014-01-01

    NASA is investigating advanced turboelectric aircraft propulsion systems that use superconducting motors to drive multiple distributed turbofans. Conventional electric motors are too large and heavy to be practical for this application; therefore, superconducting motors are required. In order to improve aircraft maneuverability, variable-speed power converters are required to throttle power to the turbofans. The low operating temperature and the need for lightweight components that place a minimum of additional heat load on the refrigeration system open the possibility of incorporating extremely efficient cryogenic power conversion technology. This Phase II project is developing critical components required to meet these goals.

  2. Ultra lightweight mirror performance at 8 degrees kelvin

    Science.gov (United States)

    Crowe, D. A.; Melugin, R. K.; Miller, J. H.

    1985-01-01

    Earlier work funded by DARPA, evaluating the optical stability of a 0.5-m ultra-lightweight, frit-bonded, fused silica mirror, is extended from the previous 100 deg K specification down to 8 deg K. The thermal stability is excellent and comparable to that for conventional fusion and solid mirrors. The total mirror change of 0.10 lambda rms (lambda = 0.6328 microns) meets the needs of most IR systems. Thermal elastic quilting is excellent (0.008 lambda). Ames Research Center and Kodak data evaluations, done independently, are in very good agreement.

  3. Repeat-PPM Super-Symbol Synchronization

    Science.gov (United States)

    Connelly, J.

    2016-11-01

    To attain a wider range of data rates in pulse position modulation (PPM) schemes with constrained pulse durations, the sender can repeat a PPM symbol multiple times, forming a super-symbol. In addition to the slot and symbol synchronization typically required for PPM, the receiver must also properly align the noisy super-symbols. We present a low-complexity approximation of the maximum-likelihood method for performing super-symbol synchronization without use of synchronization sequences. We provide simulation results demonstrating performance advantage when PPM symbols are spread by a pseudo-noise sequence, as opposed to simply repeating. Additionally, the results suggest that this super-symbol synchronization technique requires signal levels below those required for reliable communication. This validates that the PPM spreading approach proposed to CCSDS can work properly as part of the overall scheme.

  4. Axial Super-resolution Evanescent Wave Tomography

    CERN Document Server

    Pendharker, Sarang; Newman, Ward; Ogg, Stephen; Nazemifard, Neda; Jacob, Zubin

    2016-01-01

    Optical tomographic reconstruction of a 3D nanoscale specimen is hindered by the axial diffraction limit, which is 2-3 times worse than the focal plane resolution. We propose and experimentally demonstrate an axial super-resolution evanescent wave tomography (AxSET) method that enables the use of regular evanescent wave microscopes like Total Internal Reflection Fluorescence Microscope (TIRF) beyond surface imaging, and achieve tomographic reconstruction with axial super-resolution. Our proposed method based on Fourier reconstruction achieves axial super-resolution by extracting information from multiple sets of three-dimensional fluorescence images when the sample is illuminated by an evanescent wave. We propose a procedure to extract super-resolution features from the incremental penetration of an evanescent wave and support our theory by 1D (along the optical axis) and 3D simulations. We validate our claims by experimentally demonstrating tomographic reconstruction of microtubules in HeLa cells with an axi...

  5. Thermal Performance of Lightweight Solar Housing for Peri-urban Villages

    Science.gov (United States)

    Goodfield, D.; Anda, M.; Hammond, R.; Mathew, K.

    2007-10-01

    This study concerns an investigation into the thermal performance of prefabricated lightweight houses for peri-urban villages in the Perth Metropolitan region of Western Australia. Several styles of residence were selected for comparison taken from three constructed "lifestyle villages". National Lifestyle Villages Pty Ltd (NLV) is committed to quadruple bottom-line sustainability and the aim was, therefore, to provide indicators of how old and new dwellings compared under the same external conditions. The buildings themselves are prefabricated and brought to site in two halves, framed in steel clad with fibre-cement boarding, roofed in zincalume sheeting, and timber floored with applied fibre-cement sheeting. Although designed using passive solar design principles and other energy conservation measures they possess little thermal mass to improve the thermal performance. Research by the author indicated several feasible and low-budget innovative improvements for future designs, and how best to retrofit existing dwellings. NLV's aim is to provide homes for over 40,000 people in 100 villages Australia-wide by the year 2025. Any improvement in residential thermal performance can be translated not only into energy savings and greenhouse gas reduction on a significant scale, but can enhance comfort levels for residents whilst reducing their energy costs.

  6. Mirror-enhanced super-resolution microscopy

    OpenAIRE

    2016-01-01

    Axial excitation confinement beyond the diffraction limit is crucial to the development of next-generation, super-resolution microscopy. STimulated Emission Depletion (STED) nanoscopy offers lateral super-resolution using a donut-beam depletion, but its axial resolution is still over 500 nm. Total internal reflection fluorescence microscopy is widely used for single-molecule localization, but its ability to detect molecules is limited to within the evanescent field of ~ 100 nm from the cell a...

  7. Environmental external effects from wind power based on the EU ExternE methodology

    DEFF Research Database (Denmark)

    Ibsen, Liselotte Schleisner; Nielsen, Per Sieverts

    1998-01-01

    The European Commission has launched a major study project, ExternE, to develop a methodology to quantify externalities. A “National Implementation Phase”, was started under the Joule II programme with the purpose of implementing the ExternE methodology in all member states. The main objective...

  8. SuperHILAC Upgrade Project

    Energy Technology Data Exchange (ETDEWEB)

    Feinberg, B.; Brown, I.G.

    1986-06-01

    A high current MEtal Vapor Vacuum Arc (MEVVA) ion source is to be installed in the third injector (Abel) at the SuperHILAC, representing the first accelerator use of this novel ion source. The MEVVA source has produced over 1 A of uranium in all charge states, with typically more than 100 electrical mA (emA) of U/sup 5 +/. A substantial fraction of this high current, heavy ion beam must be successfully transported to the entrance of the Wideroe linac to approach the 10 emA space-charge output limit of the Wideroe. Calculations show that up to 50 emA of U/sup 5 +/ can be transported through the present high voltage column. A bouncer will be added to the Cockcroft-Walton supply to handle the increased beam current. The Low Energy Beam Transport line vacuum will be improved to reduce charge exchange, and the phase matching between the 23 MHz Wideroe and the 70 MHz Alvarez linacs will be improved by the addition of two 70 HMz bunchers. The installation of the MEVVA source along with the modifications described above are expected to result in a five-fold increase in beam delivered to Bevatron experiments, increasing the extracted uranium beam to 5 x 10/sup 7/ ions/pulse.

  9. Super-B Project Overview

    Energy Technology Data Exchange (ETDEWEB)

    Biagini, M.E.; Boni, R.; Boscolo, M.; Demma, T.; Drago, A.; Guiducci, S.; Raimondi, P.; Tomassini, S.; Zobov, M.; /Frascati; Bertsche, K.; Donald, M.; Nosochkov, Y.; Novokhatski, A.; Seeman, J.; Sullivan, M.; Yocky, G.; Wienands, U.; Wittmer, W.; /SLAC; Koop, I.; Levichev, E.; Nikitin, S.; /Novosibirsk, IYF /KEK, Tsukuba /Pisa U. /CERN

    2010-08-26

    The SuperB project aims at the construction of an asymmetric very high luminosity B-Factory on the Frascati/Tor Vergata (Italy) area, providing a uniquely sensitive probe of New Physics in the flavour sector of the Standard Model. The luminosity goal of 10{sup 36} cm{sup -2} s{sup -1} can be reached with a new collision scheme with 'large Piwinski angle' (LPA) and the use of 'crab waist sextupoles' (CW). A LPA&CW Interaction Region (IR) has been successfully tested at the DA{Phi}NE {Phi}-Factory at LNF-Frascati in 2008. The LPA&CW scheme, together with very low {beta}*, will allow for operation with relatively low beam currents and reasonable bunch length, comparable to those of PEP-II and KEKB. In the High Energy Ring (HER), two spin rotators will bring longitudinally polarized beams into collision at the IP. The lattice has been designed with a very low intrinsic emittance and is quite compact, less than 2 km long. The tight focusing requires the final doublet quadrupoles to be very close to the IP and very compact. A Conceptual Design Report was published in March 2007, and beam dynamics and collective effects R&D studies are in progress in order to publish a Technical Design Report by the end of 2010.

  10. SUPER-B LATTICE STUDIES

    Energy Technology Data Exchange (ETDEWEB)

    Biagini, M.E.; Raimondi, P.; /Frascati; Piminov, P.; Sinyatkin, S.; /Novosibirsk, IYF; Nosochkov, Y.; Wittmer, W.; /SLAC

    2010-08-25

    The SuperB asymmetric e{sup +}e{sup -} collider is designed for 10{sup 36} cm{sup -2} s{sup -1} luminosity and beam energies of 6.7 and 4.18 GeV for e{sup +} and e{sup -} respectively. The High and Low Energy Rings (HER and LER) have one Interaction Point (IP) with 66 mrad crossing angle. The 1258 m rings fit to the INFN-LNF site at Frascati. The ring emittance is minimized for the high luminosity. The Final Focus (FF) chromaticity correction is optimized for maximum transverse acceptance and energy bandwidth. Included Crab Waist sextupoles suppress betatron resonances induced in the collisions with a large Piwinski angle. The LER Spin Rotator sections provide longitudinally polarized electron beam at the IP. The lattice is flexible for tuning the machine parameters and compatible with reusing the PEP-II magnets, RF cavities and other components. Details of the lattice design are presented.

  11. Studies of the Super VELO

    CERN Document Server

    AUTHOR|(CDS)2156302

    2016-01-01

    The Super VELO is the Run 5 upgrade of the VeloPix detector of the LHCb experiment. Its most challenging task is to cope with a luminosity increase of the factor 10. This study examines the potential physics performance of a detector based on the VeloPix design at high luminosity conditions. It is found that an unmodified VeloPix detector shows poor performance when exposed to 10x design luminosity, most gravely high ghost rates of 40 %. When applying basic assumptions about material changes such as cutting the silicon thickness by half and removing the RF foil, the ghost rate drops by 20 %. When using thin silicon and re-optimizing the tracking algorithm, the ghost rate can even be reduced by 60 %. Applying the additional modification of a pixel area size four times smaller, the ghost rate drops by 88 % and the IP resolution improves. Finally, in a dream scenario with thin silicon, smaller pixels and no RF foil, big gains in resolution and a ghost rate of less than 4 % can be achieved.

  12. Sustainability assessment of a lightweight biomimetic ceiling structure.

    Science.gov (United States)

    Antony, Florian; Grießhammer, Rainer; Speck, Thomas; Speck, Olga

    2014-03-01

    An intensive and continuous debate centres on the question of whether biomimetics has a specific potential to contribute to sustainability. In the context of a case study, the objective of this paper is to contribute to this debate by presenting the first systematic approach to assess the sustainability of a complex biomimetic product. The object of inquiry is a lecture hall's ribbed slab. Based on criteria suggested by the Association of German Engineers (VDI), it has been verified that the slab has been correctly defined as biomimetic. Moreover, a systematic comparative product sustainability assessment has been carefully carried out. For purposes of comparison, estimated static calculations have been performed for conceivable current state-of-the-art lightweight ceiling structures. Alternative options are a hollow article slab and a pre-stressed flat slab. Besides a detailed benefit analysis and a discussion of social effects, their costs have also been compared. A particularly detailed life cycle assessment on the respective environmental impacts has also been performed. Results show that the biomimetic ribbed slab built in the 1960s is able to keep up with the current state-of-the-art lightweight solutions in terms of sustainability. These promising results encourage a systematic search for a broad range of sustainable biomimetic solutions.

  13. Concept for lightweight spaced-based deposition technology

    Energy Technology Data Exchange (ETDEWEB)

    Fulton, Michael; Anders, Andre

    2006-02-28

    In this contribution we will describe a technology path to very high quality coatings fabricated in the vacuum of space. To accomplish the ambitious goals set out in NASA's Lunar-Mars proposal, advanced thin-film deposition technology will be required. The ability to deposit thin-film coatings in the vacuum of lunar-space could be extremely valuable for executing this new space mission. Developing lightweight space-based deposition technology (goal:<300 g, including power supply) will enable the future fabrication and repair of flexible large-area space antennae and fixed telescope mirrors for lunar-station observatories. Filtered Cathodic Arc (FCA) is a proven terrestrial energetic thin-film deposition technology that does not need any processing gas but is well suited for ultra-high vacuum operation. Recently, miniaturized cathodic arcs have already been developed and considered for space propulsion. It is proposed to combine miniaturized pulsed FCA technology and robotics to create a robust, enabling space-based deposition system for the fabrication, improvement, and repair of thin films, especially of silver and aluminum, on telescope mirrors and eventually on large area flexible substrates. Using miniature power supplies with inductive storage, the typical low-voltage supply systems used in space are adequate. It is shown that high-value, small area coatings are within the reach of existing technology, while medium and large area coatings are challenging in terms of lightweight technology and economics.

  14. A novel lightweight Fizeau infrared interferometric imaging system

    Science.gov (United States)

    Hope, Douglas A.; Hart, Michael; Warner, Steve; Durney, Oli; Romeo, Robert

    2016-05-01

    Aperture synthesis imaging techniques using an interferometer provide a means to achieve imagery with spatial resolution equivalent to a conventional filled aperture telescope at a significantly reduced size, weight and cost, an important implication for air- and space-borne persistent observing platforms. These concepts have been realized in SIRII (Space-based IR-imaging interferometer), a new light-weight, compact SWIR and MWIR imaging interferometer designed for space-based surveillance. The sensor design is configured as a six-element Fizeau interferometer; it is scalable, light-weight, and uses structural components and main optics made of carbon fiber replicated polymer (CFRP) that are easy to fabricate and inexpensive. A three-element prototype of the SIRII imager has been constructed. The optics, detectors, and interferometric signal processing principles draw on experience developed in ground-based astronomical applications designed to yield the highest sensitivity and resolution with cost-effective optical solutions. SIRII is being designed for technical intelligence from geo-stationary orbit. It has an instantaneous 6 x 6 mrad FOV and the ability to rapidly scan a 6x6 deg FOV, with a minimal SNR. The interferometric design can be scaled to larger equivalent filled aperture, while minimizing weight and costs when compared to a filled aperture telescope with equivalent resolution. This scalability in SIRII allows it address a range of IR-imaging scenarios.

  15. Thermal performance of lightweight construction systems: Performance of `Solar One`

    Energy Technology Data Exchange (ETDEWEB)

    Hyde, R. [Queensland Univ., St. Lucia, QLD (Australia)

    1995-12-31

    Research is currently under way to asses the thermal performance of building which use new lightweight systems of construction. In particular, comparison is made between expected performance and performance found in buildings. This paper outlines the basic direction of the research and examines one particular building case study, that of Solar One. Solar One is located at Mount Coolum to the north of Brisbane on the Sunshine Coast in Queensland. This building is designed based on climatic criteria and departs from the conventional timber framed house in a number of respects. The important difference in this building is that it is a hybrid construction. Mass is used for some walls and ground floor slab and timber framing with fibre-cement for other walls. The research demonstrates to what extent the building performs to characteristics of lightweight construction systems and to what extent it performs as a heavyweight system. Focus is placed on the thermal response of the building. Conclusions reached from this case study suggest that the building does not match expected patterns of thermal response particularly in winter, there appears to be a complex heat interchange process showing clear benefits for the hybrid construction. (author). 10 figs., 4 refs.

  16. Coating Thin Mirror Segments for Lightweight X-ray Optics

    Science.gov (United States)

    Chan, Kai-Wing; Sharpe, Marton V.; Zhang, William; Kolosc, Linette; Hong, Melinda; McClelland, Ryan; Hohl, Bruce R.; Saha, Timo; Mazzarellam, James

    2013-01-01

    Next generations lightweight, high resolution, high throughput optics for x-ray astronomy requires integration of very thin mirror segments into a lightweight telescope housing without distortion. Thin glass substrates with linear dimension of 200 mm and thickness as small as 0.4 mm can now be fabricated to a precision of a few arc-seconds for grazing incidence optics. Subsequent implementation requires a distortion-free deposition of metals such as iridium or platinum. These depositions, however, generally have high coating stresses that cause mirror distortion. In this paper, we discuss the coating stress on these thin glass mirrors and the effort to eliminate their induced distortion. It is shown that balancing the coating distortion either by coating films with tensile and compressive stresses, or on both sides of the mirrors is not sufficient. Heating the mirror in a moderately high temperature turns out to relax the coated films reasonably well to a precision of about a second of arc and therefore provide a practical solution to the coating problem.

  17. Apply lightweight recognition algorithms in optical music recognition

    Science.gov (United States)

    Pham, Viet-Khoi; Nguyen, Hai-Dang; Nguyen-Khac, Tung-Anh; Tran, Minh-Triet

    2015-02-01

    The problems of digitalization and transformation of musical scores into machine-readable format are necessary to be solved since they help people to enjoy music, to learn music, to conserve music sheets, and even to assist music composers. However, the results of existing methods still require improvements for higher accuracy. Therefore, the authors propose lightweight algorithms for Optical Music Recognition to help people to recognize and automatically play musical scores. In our proposal, after removing staff lines and extracting symbols, each music symbol is represented as a grid of identical M ∗ N cells, and the features are extracted and classified with multiple lightweight SVM classifiers. Through experiments, the authors find that the size of 10 ∗ 12 cells yields the highest precision value. Experimental results on the dataset consisting of 4929 music symbols taken from 18 modern music sheets in the Synthetic Score Database show that our proposed method is able to classify printed musical scores with accuracy up to 99.56%.

  18. a Light-Weight Laser Scanner for Uav Applications

    Science.gov (United States)

    Tommaselli, A. M. G.; Torres, F. M.

    2016-06-01

    Unmanned Aerial Vehicles (UAV) have been recognized as a tool for geospatial data acquisition due to their flexibility and favourable cost benefit ratio. The practical use of laser scanning devices on-board UAVs is also developing with new experimental and commercial systems. This paper describes a light-weight laser scanning system composed of an IbeoLux scanner, an Inertial Navigation System Span-IGM-S1, from Novatel, a Raspberry PI portable computer, which records data from both systems and an octopter UAV. The performance of this light-weight system was assessed both for accuracy and with respect to point density, using Ground Control Points (GCP) as reference. Two flights were performed with the UAV octopter carrying the equipment. In the first trial, the flight height was 100 m with six strips over a parking area. The second trial was carried out over an urban park with some buildings and artificial targets serving as reference Ground Control Points. In this experiment a flight height of 70 m was chosen to improve target response. Accuracy was assessed based on control points the coordinates of which were measured in the field. Results showed that vertical accuracy with this prototype is around 30 cm, which is acceptable for forest applications but this accuracy can be improved using further refinements in direct georeferencing and in the system calibration.

  19. A LIGHT-WEIGHT LASER SCANNER FOR UAV APPLICATIONS

    Directory of Open Access Journals (Sweden)

    A. M. G. Tommaselli

    2016-06-01

    Full Text Available Unmanned Aerial Vehicles (UAV have been recognized as a tool for geospatial data acquisition due to their flexibility and favourable cost benefit ratio. The practical use of laser scanning devices on-board UAVs is also developing with new experimental and commercial systems. This paper describes a light-weight laser scanning system composed of an IbeoLux scanner, an Inertial Navigation System Span-IGM-S1, from Novatel, a Raspberry PI portable computer, which records data from both systems and an octopter UAV. The performance of this light-weight system was assessed both for accuracy and with respect to point density, using Ground Control Points (GCP as reference. Two flights were performed with the UAV octopter carrying the equipment. In the first trial, the flight height was 100 m with six strips over a parking area. The second trial was carried out over an urban park with some buildings and artificial targets serving as reference Ground Control Points. In this experiment a flight height of 70 m was chosen to improve target response. Accuracy was assessed based on control points the coordinates of which were measured in the field. Results showed that vertical accuracy with this prototype is around 30 cm, which is acceptable for forest applications but this accuracy can be improved using further refinements in direct georeferencing and in the system calibration.

  20. Efficient Hardware Implementation of the Lightweight Block Encryption Algorithm LEA

    Directory of Open Access Journals (Sweden)

    Donggeon Lee

    2014-01-01

    Full Text Available Recently, due to the advent of resource-constrained trends, such as smartphones and smart devices, the computing environment is changing. Because our daily life is deeply intertwined with ubiquitous networks, the importance of security is growing. A lightweight encryption algorithm is essential for secure communication between these kinds of resource-constrained devices, and many researchers have been investigating this field. Recently, a lightweight block cipher called LEA was proposed. LEA was originally targeted for efficient implementation on microprocessors, as it is fast when implemented in software and furthermore, it has a small memory footprint. To reflect on recent technology, all required calculations utilize 32-bit wide operations. In addition, the algorithm is comprised of not complex S-Box-like structures but simple Addition, Rotation, and XOR operations. To the best of our knowledge, this paper is the first report on a comprehensive hardware implementation of LEA. We present various hardware structures and their implementation results according to key sizes. Even though LEA was originally targeted at software efficiency, it also shows high efficiency when implemented as hardware.

  1. Optical fabrication of lightweighted 3D printed mirrors

    Science.gov (United States)

    Herzog, Harrison; Segal, Jacob; Smith, Jeremy; Bates, Richard; Calis, Jacob; De La Torre, Alyssa; Kim, Dae Wook; Mici, Joni; Mireles, Jorge; Stubbs, David M.; Wicker, Ryan

    2015-09-01

    Direct Metal Laser Sintering (DMLS) and Electron Beam Melting (EBM) 3D printing technologies were utilized to create lightweight, optical grade mirrors out of AlSi10Mg aluminum and Ti6Al4V titanium alloys at the University of Arizona in Tucson. The mirror prototypes were polished to meet the λ/20 RMS and λ/4 P-V surface figure requirements. The intent of this project was to design topologically optimized mirrors that had a high specific stiffness and low surface displacement. Two models were designed using Altair Inspire software, and the mirrors had to endure the polishing process with the necessary stiffness to eliminate print-through. Mitigating porosity of the 3D printed mirror blanks was a challenge in the face of reconciling new printing technologies with traditional optical polishing methods. The prototypes underwent Hot Isostatic Press (HIP) and heat treatment to improve density, eliminate porosity, and relieve internal stresses. Metal 3D printing allows for nearly unlimited topological constraints on design and virtually eliminates the need for a machine shop when creating an optical quality mirror. This research can lead to an increase in mirror mounting support complexity in the manufacturing of lightweight mirrors and improve overall process efficiency. The project aspired to have many future applications of light weighted 3D printed mirrors, such as spaceflight. This paper covers the design/fab/polish/test of 3D printed mirrors, thermal/structural finite element analysis, and results.

  2. A Lightweight Structure Redesign Method Based on Selective Laser Melting

    Directory of Open Access Journals (Sweden)

    Li Tang

    2016-11-01

    Full Text Available The purpose of this paper is to present a new design method of lightweight parts fabricated by selective laser melting (SLM based on the “Skin-Frame” and to explore the influence of fabrication defects on SLM parts with different sizes. Some standard lattice parts were designed according to the Chinese GB/T 1452-2005 standard and manufactured by SLM. Then these samples were tested in an MTS Insight 30 compression testing machine to study the trends of the yield process with different structure sizes. A set of standard cylinder samples were also designed according to the Chinese GB/T 228-2010 standard. These samples, which were made of iron-nickel alloy (IN718, were also processed by SLM, and then tested in the universal material testing machine INSTRON 1346 to obtain their tensile strength. Furthermore, a lightweight redesigned method was researched. Then some common parts such as a stopper and connecting plate were redesigned using this method. These redesigned parts were fabricated and some application tests have already been performed. The compression testing results show that when the minimum structure size is larger than 1.5 mm, the mechanical characteristics will hardly be affected by process defects. The cylinder parts were fractured by the universal material testing machine at about 1069.6 MPa. These redesigned parts worked well in application tests, with both the weight and fabrication time of these parts reduced more than 20%.

  3. Reactive Commercial Ni/Al Nanolayers for Joining Lightweight Alloys

    Science.gov (United States)

    Simões, Sónia; Viana, Filomena; Vieira, Manuel F.

    2014-05-01

    Reactive nanoscale multilayer foils for use in joining techniques have attracted a great deal of attention. A common feature of these nanolayers is the large amount of heat released during the reaction between the layers to form a new phase. In this study, films of alternated Ni and Al nanolayers (NanoFoil® made by the Indium Corporation) with period (bilayer thickness) close to 54 nm and with a thickness of 60 μm were used as local heat sources to bond lightweight alloys. The as-deposited Ni and Al alternated nanolayers evolve into NiAl nanometric grains when the multilayer, ignited by an electrical discharge, reacts. Joining of lightweight alloys was performed at room temperature under pressures of 10-80 MPa. The ability of the nanolayers to join these alloys by high temperature diffusion bonding was also investigated. The microstructural and chemical characterizations of the interfaces were performed on cross-sections of the joints by scanning electron microscopy and energy dispersive x-ray spectroscopy. Ni/Al nanolayers are an effective means of joining titanium alloys at room temperature. A sound interface, mainly composed by NiAl grains, is obtained in joints of TiAl/TiAl and TiAl/Inconel, produced with NanoFoil® by annealing at 700 ºC, during 60 min under a pressure of 10 MPa. The low shear strength revealed a weak adhesion of the nanofoil to the base materials.

  4. Lightweight storage and overlay networks for fault tolerance.

    Energy Technology Data Exchange (ETDEWEB)

    Oldfield, Ron A.

    2010-01-01

    The next generation of capability-class, massively parallel processing (MPP) systems is expected to have hundreds of thousands to millions of processors, In such environments, it is critical to have fault-tolerance mechanisms, including checkpoint/restart, that scale with the size of applications and the percentage of the system on which the applications execute. For application-driven, periodic checkpoint operations, the state-of-the-art does not provide a scalable solution. For example, on today's massive-scale systems that execute applications which consume most of the memory of the employed compute nodes, checkpoint operations generate I/O that consumes nearly 80% of the total I/O usage. Motivated by this observation, this project aims to improve I/O performance for application-directed checkpoints through the use of lightweight storage architectures and overlay networks. Lightweight storage provide direct access to underlying storage devices. Overlay networks provide caching and processing capabilities in the compute-node fabric. The combination has potential to signifcantly reduce I/O overhead for large-scale applications. This report describes our combined efforts to model and understand overheads for application-directed checkpoints, as well as implementation and performance analysis of a checkpoint service that uses available compute nodes as a network cache for checkpoint operations.

  5. Application of lightweight threading techniques to computational chemistry

    Science.gov (United States)

    Thornley, John; Muller, Richard P.; Mainz, Daniel T.; Çağin, Tahir; Goddard, William A.

    2001-05-01

    The recent advent of inexpensive commodity multiprocessor computers with standardized operating system support for lightweight threads provides computational chemists and other scientists with an exciting opportunity to develop sophisticated new approaches to materials simulation. We contrast the flexible performance characteristics of lightweight threading with the restrictions of traditional scientific supercomputing, based on our experiences with multithreaded molecular dynamics simulation. Motivated by the results of our molecular dynamics experiments, we propose an approach to multi-scale materials simulation using highly dynamic thread creation and synchronization within and between concurrent simulations at many different scales. This approach will enable extremely realistic simulations, with computing resources dynamically directed to areas where they are needed. Multi-scale simulations of this kind require large amounts of processing power, but are too sophisticated to be expressed using traditional supercomputing programming models. As a result, we have developed a high-level programming system called Sthreads that allows highly dynamic, nested multithreaded algorithms to be expressed. Program development is simplified through the use of innovative synchronization operations that allow multithreaded programs to be tested and debugged using standard sequential methods and tools. For this reason, Sthreads is very well suited to the complex multi-scale simulation applications that we are developing.

  6. Lightweight Provenance Service for High-Performance Computing

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Dong; Chen, Yong; Carns, Philip; Jenkins, John; Ross, Robert

    2017-09-09

    Provenance describes detailed information about the history of a piece of data, containing the relationships among elements such as users, processes, jobs, and workflows that contribute to the existence of data. Provenance is key to supporting many data management functionalities that are increasingly important in operations such as identifying data sources, parameters, or assumptions behind a given result; auditing data usage; or understanding details about how inputs are transformed into outputs. Despite its importance, however, provenance support is largely underdeveloped in highly parallel architectures and systems. One major challenge is the demanding requirements of providing provenance service in situ. The need to remain lightweight and to be always on often conflicts with the need to be transparent and offer an accurate catalog of details regarding the applications and systems. To tackle this challenge, we introduce a lightweight provenance service, called LPS, for high-performance computing (HPC) systems. LPS leverages a kernel instrument mechanism to achieve transparency and introduces representative execution and flexible granularity to capture comprehensive provenance with controllable overhead. Extensive evaluations and use cases have confirmed its efficiency and usability. We believe that LPS can be integrated into current and future HPC systems to support a variety of data management needs.

  7. Average density and porosity of high-strength lightweight concrete

    Directory of Open Access Journals (Sweden)

    A.S. Inozemtcev

    2014-11-01

    Full Text Available The analysis results of high-strength lightweight concrete (HSLWC structure are presented in this paper. The X-ray tomography, optical microscopy and other methods are used for researching of average density and porosity. It has been revealed that mixtures of HSLWC with density 1300…1500 kg/m3 have a homogeneous structure. The developed concrete has a uniform distribution of the hollow filler and a uniform layer of cement-mineral matrix. The highly saturated gas phase which is divided by denser large particles of quartz sand and products of cement hydration in the contact area allow forming a composite material with low average density, big porosity (up to 40% and high strength (compressive strength is more than 40 MPa. Special modifiers increase adhesion, compacts structure in the contact area, decrease water absorption of high-strength lightweight concrete (up to 1 % and ensure its high water resistance (water resistance coefficient is more than 0.95.

  8. Externality or sustainability economics?

    Energy Technology Data Exchange (ETDEWEB)

    Bergh, Jeroen C.J.M. van den [ICREA, Barcelona (Spain); Department of Economics and Economic History and Institute for Environmental Science and Technology, Universitat Autonoma de Barcelona (Spain)

    2010-09-15

    In an effort to develop 'sustainability economics' Baumgaertner and Quaas (2010) neglect the central concept of environmental economics-'environmental externality'. This note proposes a possible connection between the concepts of environmental externality and sustainability. In addition, attention is asked for other aspects of 'sustainability economics', namely the distinction weak/strong sustainability, spatial sustainability and sustainable trade, distinctive sustainability policy, and the ideas of early 'sustainability economists'. I argue that both sustainability and externalities reflect a systems perspective and propose that effective sustainability solutions require that more attention is given to system feedbacks, notably other-regarding preferences and social interactions, and energy and environmental rebound. The case of climate change and policy is used to illustrate particular statements. As a conclusion, a list of 20 insights and suggestions for research is offered. (author)

  9. Metasurface external cavity laser

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Luyao, E-mail: luyaoxu.ee@ucla.edu; Curwen, Christopher A.; Williams, Benjamin S. [Department of Electrical Engineering, University of California, Los Angeles, California 90095 (United States); California NanoSystems Institute, University of California, Los Angeles, California 90095 (United States); Hon, Philip W. C.; Itoh, Tatsuo [Department of Electrical Engineering, University of California, Los Angeles, California 90095 (United States); Chen, Qi-Sheng [Northrop Grumman Aerospace Systems, Redondo Beach, California 90278 (United States)

    2015-11-30

    A vertical-external-cavity surface-emitting-laser is demonstrated in the terahertz range, which is based upon an amplifying metasurface reflector composed of a sub-wavelength array of antenna-coupled quantum-cascade sub-cavities. Lasing is possible when the metasurface reflector is placed into a low-loss external cavity such that the external cavity—not the sub-cavities—determines the beam properties. A near-Gaussian beam of 4.3° × 5.1° divergence is observed and an output power level >5 mW is achieved. The polarized response of the metasurface allows the use of a wire-grid polarizer as an output coupler that is continuously tunable.

  10. External Cooling Coupled to Reduced Extremity Pressure Device

    Science.gov (United States)

    Kuznetz, Lawrence H.

    2011-01-01

    Although suited astronauts are currently cooled with a Liquid Cooled Ventilation Garment (LCVG), which can remove up to 85 percent of body heat, their effectiveness is limited because cooling must penetrate layers of skin, muscle, fat, bone, and tissue to reach the bloodstream, where its effect is prominent. Vasoconstriction further reduces the effectiveness by limiting arterial flow when exposed to cold (the frostbite response), resulting in a time constant on the order of 20 minutes from application to maximum effect. This delay can be crucial in severe exposure to hypo- or hyper-thermic conditions, compromising homeostasis. The purpose of this innovation is to provide a lightweight, effective means of delivering heat or cold from an external source directly to the bloodstream. The effectiveness of this ECCREP (External Cooling Coupled to Reduced Extremity Pressure) device is based on not having to penetrate layers of skin, muscle, fat, and tissue, thereby avoiding the thermal lag associated with their mass and heat capacity. This is accomplished by means of an outer boot operating at a slightly reduced pressure than the rest of the body, combined with an inner boot cooled or heated by an external source via water or chemicals. Heat transfer from the external source to the foot takes place by means of circulating water or flexible heat pipes.

  11. Analysis and trade-off studies of large lightweight mirror structures. [large space telescope

    Science.gov (United States)

    Soosaar, K.; Grin, R.; Ayer, F.

    1975-01-01

    A candidate mirror, hexagonally lightweighted, is analyzed under various loadings using as complete a procedure as possible. Successive simplifications are introduced and compared to an original analysis. A model which is a reasonable compromise between accuracy and cost is found and is used for making trade-off studies of the various structural parameters of the lightweighted mirror.

  12. 46 CFR 170.200 - Estimated lightweight vertical center of gravity.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Estimated lightweight vertical center of gravity. 170... Centers of Gravity § 170.200 Estimated lightweight vertical center of gravity. (a) Each tank vessel that... calculations required by §§ 170.170 and 172.065, the vertical center of gravity of a tank vessel in the...

  13. 77 FR 73615 - Lightweight Thermal Paper From Germany; Preliminary Results of Antidumping Duty Administrative...

    Science.gov (United States)

    2012-12-11

    ...] Lightweight Thermal Paper From Germany; Preliminary Results of Antidumping Duty Administrative Review; 2010... duty order on lightweight thermal paper (LWTP) from Germany for the period November 1, 2010, through... sales of subject merchandise at less than normal value, based on adverse facts available (AFA). DATES...

  14. Lightweight ZERODUR®: A Candidate Material for Affordable Future UVOIR Space Telescopes of All Apertures

    Science.gov (United States)

    Hull, Anthony B.; Westerhoff, T.; Leys, A.

    2014-01-01

    Recent Developments now make available for spaceborne applications highly lightweighted mirrors in ZERODUR®, regarded to be the “gold standard” material for thermal stability. ZERODUR® has flown on over 30 missions, including two great observatories, but not previously to this high degree of lightweighting. Now highly lightweighted mirror substrates can be made from a single billet of low expansion glass which exhibits remarkably low thermal expansion, anisotropy and inhomogeneity. This staility has the potential to simplify every aspect of a mission payload cost. A 1.2m open-back isogrid lightweighted mirror substrate has been made by SCHOTT exhibiting 88% lightweighting and a first Eigenfrequency over 200Hz. Also a recently made 0.3m isogrid lightweighted mirror exhibits ribs thinner than 0.9mm. Mirror or mirror segment substrates can be cost-effectively manufactured from monolithic blanks in apertures as small as 0.3m aperture to over 4m aperture (until recently SCHOTT maintained a line to make 8m ZERODUR® billets). We will describe this technology, the attributes of isogrid lightweighted mirror blanks, and the relevance of this material and manufacturing approach to upcoming UVOIR missions from suborbital to Explorer class to next generation Great Observatory. Lightweight ZERODUR® supports optical telescope systems requiring great stability, even in the presence of payload and scene thermal perturbations. Furthermore, mirrors or mirror segments made with the approach described can be made to remarkably short schedule, cost effectively and with little risk.

  15. 78 FR 43142 - Lightweight Thermal Paper From the People's Republic of China: Rescission of Antidumping Duty...

    Science.gov (United States)

    2013-07-19

    ... High-Tech Co., Ltd.; Henan Province Jianghe Paper Co., Ltd., Jianghe Paper Co., Ltd., and JHT Paper... wrap, a non-subject product) and 4811.90.8040 (for ``other'' including lightweight thermal paper... product) and 4811.90.9090 (for ``other,'' including lightweight thermal paper). \\8\\ As of January 1,...

  16. Method for calculating thermal properties of lightweight floor heating panels based on an experimental setup

    DEFF Research Database (Denmark)

    Weitzmann, Peter; Svendsen, Svend

    2005-01-01

    Lightweight floor heating systems consist of a plastic tube connected to a heat distribution aluminium plate and are used in wooden floor constructions. The thermal properties of lightweight floor heating systems cannot be described accurately. The reason is a very complex interaction of convecti...

  17. 78 FR 23220 - Lightweight Thermal Paper From Germany: Final Results of Antidumping Duty Administrative Review...

    Science.gov (United States)

    2013-04-18

    ... International Trade Administration Lightweight Thermal Paper From Germany: Final Results of Antidumping Duty... from Germany.\\1\\ The period of review (POR) is November 1, 2010, through October 31, 2011. We invited... in the section entitled ``Final Results of Review.'' \\1\\ See Lightweight Thermal Paper from...

  18. External inverse-Compton emission from jetted tidal disruption events

    CERN Document Server

    Lu, Wenbin

    2016-01-01

    The recent discoveries of Swift J1644+57 and J2058+05 show that tidal disruption events (TDEs) can launch relativistic jets. Super-Eddington accretion produces a strong radiation field of order Eddington luminosity. In a jetted TDE, electrons in the jet will inverse-Compton scatter the external radiation field from the accretion disk and wind. Motivated by observations of thermal optical-UV spectra in Swift J2058+05 and several other TDEs, we assume the spectrum of the external radiation field intercepted by the relativistic jet to be blackbody. Hot electrons in the jet scatter this thermal radiation and produce luminosities 10^45-10^48 erg/s in the X/gamma-ray band. This model of thermal plus inverse-Compton radiation is applied to Swift J2058+05. First, we show that the blackbody component in the optical-UV spectrum most likely has its origin in the super-Eddington wind from the disk. Then, using the observed blackbody component as the external radiation field, we show that the X-ray luminosity and spectrum...

  19. EFFECTS OF LIGHTWEIGHT MULLITE-SILICA RICH GLASS COMPOSITE AGGREGATES ON PROPERTIES OF CASTABLES

    Directory of Open Access Journals (Sweden)

    Li Y.

    2013-09-01

    Full Text Available Mullite-silica rich glass (MSRG composite is a material which is more efficient than chamotte for refractory utilization of clay. The effects of lightweight MSRG composite aggregate on the properties of refractory castables were studied by XRD, SEM and EDS, etc. Comparing with a common lightweight chamotte aggregate, it was found that the hot modulus of rupture, refractoriness under load and thermal shock resistance of the castable with lightweight MSRG aggregate were higher than those of the castable with a common lightweight chamotte aggregate because MSRG did not contain silica crystalline phases and contained a liquid phase with very high viscosity at high temperature. The castables with lightweight chamotte aggregate have higher thermal expansion because of existence of cristobalite and quartz, and have lower thermal conductivity because of higher porosity.

  20. Properties of Structural Lightweight Concrete Filled with Palm-Based Polyurethane

    Directory of Open Access Journals (Sweden)

    Kamarul Aini Mohd Sari

    2014-09-01

    Full Text Available Four experiments were conducted to characterize the properties of palm-based polyurethane (PU foam in lightweight concrete. The PU foam was synthesized from palm kernel oil-based polyol reacted with 2, 4-methylene diphenyl diisocyanate. Polyurethane as lightweight aggregate was mixed with ordinary cement, sand, and water to form lightweight concrete. The microstructure of PU aggregate can be accessed from optical micrographs. Density, compressive strength, distribution of fine aggregate, and the interfacial zone were also investigated. The result showed that palm-based lightweight concrete has excellent compressive strength (17.5 MPa, and fulfilled the minimum strength requirement for structural concrete. Palm-based lightweight concrete with 0.6 w/c ratio and 3% w/w PU system achieved 1770 kg/m3 presented uniform dispersion of aggregate and excellent mechanical bonding.

  1. Constant External Fields in Gauge Theory and the Spin 0, 1/2, 1 Path Integrals

    CERN Document Server

    Reuter, M; Schubert, C; Reuter, Martin; Schmidt, Michael G.; Schubert, Christian

    1996-01-01

    We investigate the usefulness of the ``string-inspired technique'' for gauge theory calculations in a constant external field background. Our approach is based on Strassler's worldline path integral approach to the Bern-Kosower formalism, and on the construction of worldline (super--) Green's functions incorporating external fields as well as internal propagators. The worldline path integral representation of the gluon loop is reexamined in detail. We calculate the two-loop effective actions induced for a constant external field by a scalar and spinor loop, and the corresponding one-loop effective action in the gluon loop case.

  2. Stochastic Control - External Models

    DEFF Research Database (Denmark)

    Poulsen, Niels Kjølstad

    2005-01-01

    This note is devoted to control of stochastic systems described in discrete time. We are concerned with external descriptions or transfer function model, where we have a dynamic model for the input output relation only (i.e.. no direct internal information). The methods are based on LTI systems...

  3. Productivity Change and Externalities

    DEFF Research Database (Denmark)

    Kravtsova, Victoria

    2014-01-01

    firms and the economy as a whole. The approach used in the current research accounts for different internal as well as external factors that individual firms face and evaluates the effect on changes in productivity, technology as well as the efficiency of domestic firms. The empirical analysis focuses...... change in different types of firms and sectors of the economy...

  4. Multiple external root resorption.

    Science.gov (United States)

    Yusof, W Z; Ghazali, M N

    1989-04-01

    Presented is an unusual case of multiple external root resorption. Although the cause of this resorption was not determined, several possibilities are presented. Trauma from occlusion, periodontal and pulpal inflammation, and resorption of idiopathic origin are all discussed as possible causes.

  5. Super-multiplex vibrational imaging

    Science.gov (United States)

    Wei, Lu; Chen, Zhixing; Shi, Lixue; Long, Rong; Anzalone, Andrew V.; Zhang, Luyuan; Hu, Fanghao; Yuste, Rafael; Cornish, Virginia W.; Min, Wei

    2017-04-01

    potential of this 24-colour (super-multiplex) optical imaging approach for elucidating intricate interactions in complex biological systems.

  6. The Micro-Instrumentation Package: A Solution to Lightweight Ballooning

    Science.gov (United States)

    Juneau, Jill

    This paper discusses the design and testing of an over the horizon (OTH) light weight telemetry and termination system that can be used for small ballooning payloads. Currently, the Columbia Scientific Balloon Facility (CSBF) provides telemetry for the science payload by integrating one of two types of support packages. The type of support package integrated depends on whether the flight will stay in range of line of sight (LOS) or will exceed LOS requiring the use of over the horizon (OTH) telemetry. The weights of these systems range from 100 pounds to 350 pounds depending upon the use of redundant systems, equipment for high data rates, and batteries and/or solar panels for power requirements. These weight values are not as significant for larger payloads but can be crippling for smaller payloads. In addition, these support package systems are fairly expensive, placing a high importance on recovery. A lightweight and inexpensive telemetry system could be beneficial for various reasons. First, it would allow scientists to fly lightweight payloads on large balloons reaching even higher altitudes. Second, scientists could fly lightweight payloads on less expensive balloons such as meteorological balloons. Depending on the payload, these flights could be fairly inexpensive and even disposable. Third, a compact telemetry system on any balloon will free up more room for the science portion of the payload. In response, a compact telemetry/termination system called the Micro-Instrumentation Package (MIP) was developed. The MIP provides uplink and downlink communications, an interface to the science, housekeeping information including global positioning system (GPS) position, and relays. Instead of a power-hungry microprocessor, the MIP's central consists of a microcontroller. Microcontrollers are lower power, easily programmed, and can be purchased for less than ten dollars. For uplink and downlink telemetry, the MIP uses an LOS serial transceiver and an Iridium unit

  7. Energy reduction through voltage scaling and lightweight checking

    Science.gov (United States)

    Kadric, Edin

    As the semiconductor roadmap reaches smaller feature sizes and the end of Dennard Scaling, design goals change, and managing the power envelope often dominates delay minimization. Voltage scaling remains a powerful tool to reduce energy. We find that it results in about 60% geomean energy reduction on top of other common low-energy optimizations with 22nm CMOS technology. However, when voltage is reduced, it becomes easier for noise and particle strikes to upset a node, potentially causing Silent Data Corruption (SDC). The 60% energy reduction, therefore, comes with a significant drop in reliability. Duplication with checking and triple-modular redundancy are traditional approaches used to combat transient errors, but spending 2--3x the energy for redundant computation can diminish or reverse the benefits of voltage scaling. As an alternative, we explore the opportunity to use checking operations that are cheaper than the base computation they are guarding. We devise a classification system for applications and their lightweight checking characteristics. In particular, we identify and evaluate the effectiveness of lightweight checks in a broad set of common tasks in scientific computing and signal processing. We find that the lightweight checks cost only a fraction of the base computation (0-25%) and allow us to recover the reliability losses from voltage scaling. Overall, we show about 50% net energy reduction without compromising reliability compared to operation at the nominal voltage. We use FPGAs (Field-Programmable Gate Arrays) in our work, although the same ideas can be applied to different systems. On top of voltage scaling, we explore other common low-energy techniques for FPGAs: transmission gates, gate boosting, power gating, low-leakage (high-Vth) processes, and dual-V dd architectures. We do not scale voltage for memories, so lower voltages help us reduce logic and interconnect energy, but not memory energy. At lower voltages, memories become dominant

  8. Lightweight and Statistical Techniques for Petascale PetaScale Debugging

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Barton

    2014-06-30

    This project investigated novel techniques for debugging scientific applications on petascale architectures. In particular, we developed lightweight tools that narrow the problem space when bugs are encountered. We also developed techniques that either limit the number of tasks and the code regions to which a developer must apply a traditional debugger or that apply statistical techniques to provide direct suggestions of the location and type of error. We extend previous work on the Stack Trace Analysis Tool (STAT), that has already demonstrated scalability to over one hundred thousand MPI tasks. We also extended statistical techniques developed to isolate programming errors in widely used sequential or threaded applications in the Cooperative Bug Isolation (CBI) project to large scale parallel applications. Overall, our research substantially improved productivity on petascale platforms through a tool set for debugging that complements existing commercial tools. Previously, Office Of Science application developers relied either on primitive manual debugging techniques based on printf or they use tools, such as TotalView, that do not scale beyond a few thousand processors. However, bugs often arise at scale and substantial effort and computation cycles are wasted in either reproducing the problem in a smaller run that can be analyzed with the traditional tools or in repeated runs at scale that use the primitive techniques. New techniques that work at scale and automate the process of identifying the root cause of errors were needed. These techniques significantly reduced the time spent debugging petascale applications, thus leading to a greater overall amount of time for application scientists to pursue the scientific objectives for which the systems are purchased. We developed a new paradigm for debugging at scale: techniques that reduced the debugging scenario to a scale suitable for traditional debuggers, e.g., by narrowing the search for the root-cause analysis

  9. Bed form dynamics in distorted lightweight scale models

    Science.gov (United States)

    Aberle, Jochen; Henning, Martin; Ettmer, Bernd

    2016-04-01

    The adequate prediction of flow and sediment transport over bed forms presents a major obstacle for the solution of sedimentation problems in alluvial channels because bed forms affect hydraulic resistance, sediment transport, and channel morphodynamics. Moreover, bed forms can affect hydraulic habitat for biota, may introduce severe restrictions to navigation, and present a major problem for engineering structures such as water intakes and groynes. The main body of knowledge on the geometry and dynamics of bed forms such as dunes originates from laboratory and field investigations focusing on bed forms in sand bed rivers. Such investigations enable insight into the physics of the transport processes, but do not allow for the long term simulation of morphodynamic development as required to assess, for example, the effects of climate change on river morphology. On the other hand, this can be achieved through studies with distorted lightweight scale models allowing for the modification of the time scale. However, our understanding of how well bed form geometry and dynamics, and hence sediment transport mechanics, are reproduced in such models is limited. Within this contribution we explore this issue using data from investigations carried out at the Federal Waterways and Research Institute in Karlsruhe, Germany in a distorted lightweight scale model of the river Oder. The model had a vertical scale of 1:40 and a horizontal scale of 1:100, the bed material consisted of polystyrene particles, and the resulting dune geometry and dynamics were measured with a high spatial and temporal resolution using photogrammetric methods. Parameters describing both the directly measured and up-scaled dune geometry were determined using the random field approach. These parameters (e.g., standard deviation, skewness, kurtosis) will be compared to prototype observations as well as to results from the literature. Similarly, parameters describing the lightweight bed form dynamics, which

  10. 75 FR 41439 - Lightweight Thermal Paper from Germany: Extension of Time Limits for the Preliminary Results of...

    Science.gov (United States)

    2010-07-16

    ... International Trade Administration Lightweight Thermal Paper from Germany: Extension of Time Limits for the... antidumping duty order on lightweight thermal paper from Germany (LTWP), covering the period November 20, 2008... cost of production. See Lightweight Thermal Paper from Germany: Notice of Preliminary Determination...

  11. 76 FR 22078 - Lightweight Thermal Paper From Germany: Notice of Final Results of the First Antidumping Duty...

    Science.gov (United States)

    2011-04-20

    ... International Trade Administration Lightweight Thermal Paper From Germany: Notice of Final Results of the First... administrative review for the antidumping duty order on lightweight thermal paper from Germany.\\2\\ The review... October 31, 2009. \\1\\ See Lightweight Thermal Paper from Germany: Notice of Partial Rescission...

  12. Axial super-resolution evanescent wave tomography.

    Science.gov (United States)

    Pendharker, Sarang; Shende, Swapnali; Newman, Ward; Ogg, Stephen; Nazemifard, Neda; Jacob, Zubin

    2016-12-01

    Optical tomographic reconstruction of a three-dimensional (3D) nanoscale specimen is hindered by the axial diffraction limit, which is 2-3 times worse than the focal plane resolution. We propose and experimentally demonstrate an axial super-resolution evanescent wave tomography method that enables the use of regular evanescent wave microscopes like the total internal reflection fluorescence microscope beyond surface imaging and achieve a tomographic reconstruction with axial super-resolution. Our proposed method based on Fourier reconstruction achieves axial super-resolution by extracting information from multiple sets of 3D fluorescence images when the sample is illuminated by an evanescent wave. We propose a procedure to extract super-resolution features from the incremental penetration of an evanescent wave and support our theory by one-dimensional (along the optical axis) and 3D simulations. We validate our claims by experimentally demonstrating tomographic reconstruction of microtubules in HeLa cells with an axial resolution of ∼130  nm. Our method does not require any additional optical components or sample preparation. The proposed method can be combined with focal plane super-resolution techniques like stochastic optical reconstruction microscopy and can also be adapted for THz and microwave near-field tomography.

  13. Axial super-resolution evanescent wave tomography

    Science.gov (United States)

    Pendharker, Sarang; Shende, Swapnali; Newman, Ward; Ogg, Stephen; Nazemifard, Neda; Jacob, Zubin

    2016-12-01

    Optical tomographic reconstruction of a 3D nanoscale specimen is hindered by the axial diffraction limit, which is 2-3 times worse than the focal plane resolution. We propose and experimentally demonstrate an axial super-resolution evanescent wave tomography (AxSET) method that enables the use of regular evanescent wave microscopes like Total Internal Reflection Fluorescence Microscope (TIRF) beyond surface imaging, and achieve tomographic reconstruction with axial super-resolution. Our proposed method based on Fourier reconstruction achieves axial super-resolution by extracting information from multiple sets of three-dimensional fluorescence images when the sample is illuminated by an evanescent wave. We propose a procedure to extract super-resolution features from the incremental penetration of an evanescent wave and support our theory by 1D (along the optical axis) and 3D simulations. We validate our claims by experimentally demonstrating tomographic reconstruction of microtubules in HeLa cells with an axial resolution of $\\sim$130 nm. Our method does not require any additional optical components or sample preparation. The proposed method can be combined with focal plane super-resolution techniques like STORM and can also be adapted for THz and microwave near-field tomography.

  14. Lightweight performance data collectors 2.0 with Eiger support.

    Energy Technology Data Exchange (ETDEWEB)

    Allan, Benjamin A.

    2013-05-01

    We report on the use and design of a portable, extensible performance data collection tool motivated by modeling needs of the high performance computing systems co-design com- munity. The lightweight performance data collectors with Eiger support is intended to be a tailorable tool, not a shrink-wrapped library product, as pro ling needs vary widely. A single code markup scheme is reported which, based on compilation ags, can send perfor- mance data from parallel applications to CSV les, to an Eiger mysql database, or (in a non-database environment) to at les for later merging and loading on a host with mysql available. The tool supports C, C++, and Fortran applications.

  15. Lightweight Mechanical Metamaterials with Tunable Negative Thermal Expansion.

    Science.gov (United States)

    Wang, Qiming; Jackson, Julie A; Ge, Qi; Hopkins, Jonathan B; Spadaccini, Christopher M; Fang, Nicholas X

    2016-10-21

    Ice floating on water is a great manifestation of negative thermal expansion (NTE) in nature. The limited examples of natural materials possessing NTE have stimulated research on engineered structures. Previous studies on NTE structures were mostly focused on theoretical design with limited experimental demonstration in two-dimensional planar geometries. In this work, aided with multimaterial projection microstereolithography, we experimentally fabricate lightweight multimaterial lattices that exhibit significant negative thermal expansion in three directions and over a temperature range of 170 degrees. Such NTE is induced by the structural interaction of material components with distinct thermal expansion coefficients. The NTE can be tuned over a large range by varying the thermal expansion coefficient difference between constituent beams and geometrical arrangements. Our experimental results match qualitatively with a simple scaling law and quantitatively with computational models.

  16. Alumina lightweight ceramics modified with plasma synthesized nanopowders

    Science.gov (United States)

    Zake, I.; Svinka, R.; Svinka, V.; Palcevskis, E.

    2011-12-01

    The aim of this study is to clarify possibilities of using plasma synthesized Al2O3 and SiC nanopowders as additives in alumina lightweight ceramics prepared by slip casting. Each plasma synthesized nanopowder (PSNP) was incorporated in the material by a different method, because of their diverse influence on the properties of slip. Al2O3 PSNP was introduced in the matrix in form of aqueous suspension. SiC nanopowder was added directly to raw materials. Bending strength, bulk density, apparent porosity and thermal shock resistance were determined to evaluate the influence of these additives. The effect of Al2O3 PSNP addition on the properties of material depends on the initial sintering temperature. SiC particles during sintering oxidize into SiO2 and then in the reaction with alumina form mullite. Addition of SiC considerably improves bending strength and thermal shock resistance.

  17. Lightweight Interactions for Reciprocal Cooperation in a Social Network Game

    CERN Document Server

    Takano, Masanori; Fukuda, Ichiro

    2016-01-01

    The construction of reciprocal relationships requires cooperative interactions during the initial meetings. However, cooperative behavior with strangers is risky because the strangers may be exploiters. In this study, we show that people increase the likelihood of cooperativeness of strangers by using lightweight non-risky interactions in risky situations based on the analysis of a social network game (SNG). They can construct reciprocal relationships in this manner. The interactions involve low-cost signaling because they are not generated at any cost to the senders and recipients. Theoretical studies show that low-cost signals are not guaranteed to be reliable because the low-cost signals from senders can lie at any time. However, people used low-cost signals to construct reciprocal relationships in an SNG, which suggests the existence of mechanisms for generating reliable, low-cost signals in human evolution.

  18. The 3D lightweight structural characteristics of the beetle forewing.

    Science.gov (United States)

    Chen, Jinxiang; Tuo, Wanyong; Guo, Zhensheng; Yan, Lili

    2017-02-01

    The present paper renewedly expounds upon the characteristics of the 3D lightweight structure of beetle forewings and notes that two biomimetic structures (models) that have appeared in recent years do not comply with these characteristics based on a comparison of the structures of the biological prototypes. The first model features transverse tubules based on observations of circular holes in cross-sectional figures of the Cybister forewing. The second is a biomimetic spherical cavity model with hollow trabeculae that reportedly exhibits superior mechanical properties because its structures are most similar to the biological prototype. Finally, a false biomimetic proposition that the mechanical properties of biomimetic structures with "fiber winding" patterns are superior to those of structures constructed of pure "epoxy" is also noted. Hopefully, the present study can serve to improve the state of research on biomimetic applications of beetle forewing structures.

  19. Lightweight Mechanical Metamaterials with Tunable Negative Thermal Expansion

    Science.gov (United States)

    Wang, Qiming; Jackson, Julie A.; Ge, Qi; Hopkins, Jonathan B.; Spadaccini, Christopher M.; Fang, Nicholas X.

    2016-10-01

    Ice floating on water is a great manifestation of negative thermal expansion (NTE) in nature. The limited examples of natural materials possessing NTE have stimulated research on engineered structures. Previous studies on NTE structures were mostly focused on theoretical design with limited experimental demonstration in two-dimensional planar geometries. In this work, aided with multimaterial projection microstereolithography, we experimentally fabricate lightweight multimaterial lattices that exhibit significant negative thermal expansion in three directions and over a temperature range of 170 degrees. Such NTE is induced by the structural interaction of material components with distinct thermal expansion coefficients. The NTE can be tuned over a large range by varying the thermal expansion coefficient difference between constituent beams and geometrical arrangements. Our experimental results match qualitatively with a simple scaling law and quantitatively with computational models.

  20. Lightweight Phishing URLs Detection Using N-gram Features

    Directory of Open Access Journals (Sweden)

    Ammar Yahya Daeef

    2016-06-01

    Full Text Available Phishing is a kind of attack that belongs to social engineering and this attack seeks to trick people in order to let them reveal their confidential information. Several methods are introduced to detect phishing websites by using different types of features. Unfortunately, these techniques implemented for specific attack vector such as detecting phishing emails which make implementing wide scope detection system crucial demand. URLs analysis proved to be a strong method to detect malicious attacks by previous researches. This technique uses various URL features such as host information, lexical, and other type of features. In this paper, we present wide scope and lightweight phishing detection system using lexical features only. The proposed classifier provides accuracy of 93% with 0.12 second processing time per URL.

  1. Robustness of Modal Parameter Estimation Methods Applied to Lightweight Structures

    DEFF Research Database (Denmark)

    Dickow, Kristoffer Ahrens; Kirkegaard, Poul Henning; Andersen, Lars Vabbersgaard

    2013-01-01

    of nominally identical test subjects. However, the literature on modal testing of timber structures is rather limited and the applicability and robustness of dierent curve tting methods for modal analysis of such structures is not described in detail. The aim of this paper is to investigate the robustness....... The ability to handle closely spaced modes and broad frequency ranges is investigated for a numerical model of a lightweight junction under dierent signal-to-noise ratios. The selection of both excitation points and response points are discussed. It is found that both the Rational Fraction Polynomial-Z method...... of two parameter estimation methods built into the commercial modal testing software B&K Pulse Re ex Advanced Modal Analysis. The investigations are done by means of frequency response functions generated from a nite-element model and subjected to articial noise before being analyzed with Pulse Re ex...

  2. SCIENTIFIC AND TECHNICAL PRECONDITIONS FOR EXTRUDED LIGHTWEIGHT CEMENT SYSTEMS

    Directory of Open Access Journals (Sweden)

    Oreshkin Dmitriy Vladimirovich

    2012-10-01

    The paper also presents the results of the research of the microstructure of spilt Portland cement and hollow glass spheres, their mineral and chemical analyses, as well as the properties of masonry mortars. The paper presents a conclusion that their high process-dependent parameters and superior operating performance are attainable through the introduction of effective hollow glass spheres into masonry mortars and the application of the extrusion method. The aforementioned novelties may reduce the water consumption rate, improve the strength, freeze resistance and durability of cement mortars. The preparation of this paper involved the study of nine reference books. This paper is the first one of a series of papers covering the method of extrusion of lightweight cement mortars.

  3. A Light-Weight Communication Library for Distributed Computing

    CERN Document Server

    Groen, Derek; Grosso, Paola; de Laat, Cees; Zwart, Simon Portegies; 10.1088/1749-4699/3/1/015002

    2010-01-01

    We present MPWide, a platform independent communication library for performing message passing between computers. Our library allows coupling of several local MPI applications through a long distance network and is specifically optimized for such communications. The implementation is deliberately kept light-weight, platform independent and the library can be installed and used without administrative privileges. The only requirements are a C++ compiler and at least one open port to a wide area network on each site. In this paper we present the library, describe the user interface, present performance tests and apply MPWide in a large scale cosmological N-body simulation on a network of two computers, one in Amsterdam and the other in Tokyo.

  4. Thermal conductivity of newspaper sandwiched aerated lightweight concrete panel

    Energy Technology Data Exchange (ETDEWEB)

    Ng, Soon-Ching; Low, Kaw-Sai [Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Jalan Genting Kelang, Setapak, 53300 Kuala Lumpur, Wilayah Persekutuan (Malaysia)

    2010-12-15

    Investigation on the thermal conductivity of newspaper sandwiched aerated lightweight concrete (ALC) panels is the main purpose of this study. Various densities of ALC panels ranging from 1700, 1400 and 1100 kg/m{sup 3} with three different aerial intensities of newspaper sandwiched were produced. Investigation was limited to the effect of aerial intensity of newspaper sandwiched and the effect of density of ALC on thermal conductivity. It is found that the thermal conductivity of newspaper sandwiched ALC panels reduced remarkably compared to control ALC panels. The reduction was recorded at 18.0%, 21.8% and 20.7% correspond to densities of 1700, 1400 and 1100 kg/m{sup 3} with just a mere 0.05 g/cm{sup 2} aerial intensity of newspaper sandwiched. Newspaper sandwiched has a significant impact on the performance of thermal conductivity of ALC panels based on regression analysis. (author)

  5. Research on the Mo del of a Lightweight Resource Addressing

    Institute of Scientific and Technical Information of China (English)

    LUO Bingqing; SUN Zhixin

    2015-01-01

    This paper discussed the characteristics of addressing from the perspective of Internet address-ing mechanism. An Internet of things (IOT) resource ad-dressing iteration model was defined. In the model, a di-rect addressing mode for active nodes and an indirect addressing mode for passive codes were proposed, which meet the requirement for multiple encoding mode. A uni-fied IOT resource lightweight addressing scheme based on IPv6 has been proposed to implement the two addressing modes. The scheme utilized the virtual domain to solve the problem of the heterogeneous encoding. The paper imple-mented the addressing process from the Internet host to the sensor node based on IPv6 over low-power wireless personal area networks (6LoWPAN) protocol. The experi-ment results show that the scheme is performed to realize communication between wireless sensor networks and IPv6 networks.

  6. Vibration Transmission in a Multi-Storey Lightweight Building

    DEFF Research Database (Denmark)

    Niu, Bin; Andersen, Lars Vabbersgaard; Kiel, Nikolaj

    2012-01-01

    This paper develops a parametric modelling and analysis approach to investigate the vibration transmission in lightweight buildings. The main focus of the research is to investigate the influence of geometry and configuration of the building on the vibration transmission. A building with a single......, vibro-acoustic analysis is performed by means of a simple version of the model, where the entire building is constructed by translation and combination of uniform basic modular elements, i.e. wall and floor panels. Each room is created by choosing the component modules from a predefined group of panels...... the modelling of different connections between panels in the building [2]. Using this parametric building model, free vibration analysis is first performed to obtain the distribution of Eigen frequencies of the building. Then the forced vibration of the building subjected to a mechanical excitation is analysed...

  7. Modification of Lightweight Aggregates’ Microstructure by Used Motor Oil Addition

    Directory of Open Access Journals (Sweden)

    Małgorzata Franus

    2016-10-01

    Full Text Available An admixture of lightweight aggregate substrates (beidellitic clay containing 10 wt % of natural clinoptilolite or Na-P1 zeolite with used motor oil (1 wt %–8 wt % caused marked changes in the aggregates’ microstructure, measured by a combination of mercury porosimetry (MIP, microtomography (MT, and scanning electron microscopy. Maximum porosity was produced at low (1%–2% oil concentrations and it dropped at higher concentrations, opposite to the aggregates’ bulk density. Average pore radii, measured by MIP, decreased with an increasing oil concentration, whereas larger (MT pore sizes tended to increase. Fractal dimension, derived from MIP data, changed similarly to the MIP pore radius, while that derived from MT remained unaltered. Solid phase density, measured by helium pycnometry, initially dropped slightly and then increased with the amount of oil added, which was most probably connected to changes in the formation of extremely small closed pores that were not available for He atoms.

  8. A Lightweight, User-controlled System For The Home

    Directory of Open Access Journals (Sweden)

    Lynne Baillie

    2006-01-01

    Full Text Available This paper explores how we designed, with input from some elderly persons, a multi-agent user-controlled network for the home. The system was designed to support the elderly in living longer at home with minimal support. We describe how our work attempts to tackle issues such as privacy, control of personal space, and enjoyment within the home. As the number of elderly individuals’ increases, a certain amount of information gathering or support may be required to assist the elderly in their homes. However, we strongly believe that we should preserve people’s privacy in their homes and ensure that any artifact we propose is seen as enjoyable, aesthetically pleasing and, most importantly, not stigmatizing. We describe in this paper how a lightweight setup, using a multimodal mobile robot, a PDA, and an interactive television, can assist the elderly in the home in an enjoyable and unobtrusive way.

  9. Vibration Transmission in a Multi-Storey Lightweight Building

    DEFF Research Database (Denmark)

    Niu, Bin; Andersen, Lars Vabbersgaard; Kiel, Nikolaj

    2012-01-01

    This paper develops a parametric modelling and analysis approach to investigate the vibration transmission in lightweight buildings. The main focus of the research is to investigate the influence of geometry and configuration of the building on the vibration transmission. A building with a single...... to investigate the transmission of vibration. The influence of different excitation frequencies on the vibration transmission is studied and discussed. The vibration response in two different receiving rooms, one near the source and one far from the source, is illustrated and discussed for the various geometric...... in vibration transmission in a building. The influence on the flanking transmission of introducing a neighbouring room in the direction along the building or on top of the building is discussed. •The vibration transmission in buildings with different room sizes is analyzed and discussed. Based on the parameter...

  10. The use of spent glauconite in lightweight aggregate production

    Directory of Open Access Journals (Sweden)

    Franus, Wojciech

    2011-08-01

    Full Text Available The presented work has shown an application of spent glauconite bed after purification of wastewater for production of lightweight expanded clay aggregates. Sewage, from which it was removed Zn ions, came from technological line (zincworks of Communication Equipment Factory „PZL” Świdnik. Spent glauconite bed was used as an additive in lightweight aggregate production which was obtained using plastic method by sintering, at temperature 1140 ºC and 1200 ºC, of spent glauconite amouts 10, 15, 20 and 25% wt. with clays from open-cast mine „Budy Mszczonowskie”. The presence of the mineral improves sinter texture, increases porosity and contributes to formation of glassy layer on the surface of the aggregates. Tests of zinc elution from lightweight of aggregate samples has shown very low mobility of zinc ions. Content of zinc in water extracts obtained from lightweight of aggregate is definitely lower than zinc concentration permitted for sewage discharge to water or soil, means that spent material is not offensive for the environment as it can be used as a high quality building product.

    El trabajo presentado ha demostrado una aplicación de agotado depósito de glauconita después de la purificación de aguas residuales para la producción de áridos ligeros de arcilla expandida. Las aguas residuales, de la que fueron eliminados los iones Zn, vinieron de la línea tecnológica del equipo de comunicación de la fábrica “PZL” Świdnik. Agotado depósito de glauconita se utiliza como aditivo en la producción de áridos ligeros que se obtuvo utilizando el método de plástico de la sinterización, a temperatura C. 1140 º y 1200 º C, de spent glauconita amouts10, 15, 20 y 25% en peso. con arcillas de la mina a cielo abierto “Budy Mszczonowskie”. La presencia de este mineral mejora la textura de sinterización, aumenta la porosidad y contribuye a la formación de la capa vítrea en la superficie de los agregados. Pruebas de

  11. Lightweight link dimensioning using sFlow sampling

    DEFF Research Database (Denmark)

    de Oliviera Schmidt, Ricardo; Sadre, Ramin; Sperotto, Anna

    2013-01-01

    not be trivial in high-speed links. Aiming scalability, operators often deploy packet sampling on monitoring, but little is known how it affects link dimensioning. In this paper we assess the feasibility of lightweight link dimensioning using sFlow, which is a widely-deployed traffic monitoring tool. We...... implement sFlow sampling algorithm and use a previously proposed and validated dimensioning formula that needs traffic variance. We validate our approach using packet captures from real networks. Results show that the proposed procedure is successful for a range of sampling rates and that, due to randomness...... of sampling algorithm, the error introduced by scaling the traffic variance yields more conservative results that cope with short-term traffic fluctuations....

  12. LPKI - A Lightweight Public Key Infrastructure for the Mobile Environments

    CERN Document Server

    Toorani, Mohsen; 10.1109/ICCS.2008.4737164

    2010-01-01

    The non-repudiation as an essential requirement of many applications can be provided by the asymmetric key model. With the evolution of new applications such as mobile commerce, it is essential to provide secure and efficient solutions for the mobile environments. The traditional public key cryptography involves huge computational costs and is not so suitable for the resource-constrained platforms. The elliptic curve-based approaches as the newer solutions require certain considerations that are not taken into account in the traditional public key infrastructures. The main contribution of this paper is to introduce a Lightweight Public Key Infrastructure (LPKI) for the constrained platforms such as mobile phones. It takes advantages of elliptic curve cryptography and signcryption to decrease the computational costs and communication overheads, and adapting to the constraints. All the computational costs of required validations can be eliminated from end-entities by introduction of a validation authority to th...

  13. Lightweight Mutual Authentication Protocol for Low Cost RFID Tags

    CERN Document Server

    Ahmed, Eslam Gamal; Hashem, Mohamed; 10.5121/ijnsa.2010.2203

    2010-01-01

    Radio Frequency Identification (RFID) technology one of the most promising technologies in the field of ubiquitous computing. Indeed, RFID technology may well replace barcode technology. Although it offers many advantages over other identification systems, there are also associated security risks that are not easy to be addressed. When designing a real lightweight authentication protocol for low cost RFID tags, a number of challenges arise due to the extremely limited computational, storage and communication abilities of Low-cost RFID tags. This paper proposes a real mutual authentication protocol for low cost RFID tags. The proposed protocol prevents passive attacks as active attacks are discounted when designing a protocol to meet the requirements of low cost RFID tags. However the implementation of the protocol meets the limited abilities of low cost RFID tags.

  14. Lightweight Distance bound Protocol for Low Cost RFID Tags

    CERN Document Server

    Ahmed, Eslam Gamal; Hashem, Mohamed

    2010-01-01

    Almost all existing RFID authentication schemes (tag/reader) are vulnerable to relay attacks, because of their inability to estimate the distance to the tag. These attacks are very serious since it can be mounted without the notice of neither the reader nor the tag and cannot be prevented by cryptographic protocols that operate at the application layer. Distance bounding protocols represent a promising way to thwart relay attacks, by measuring the round trip time of short authenticated messages. All the existing distance bounding protocols use random number generator and hash functions at the tag side which make them inapplicable at low cost RFID tags. This paper proposes a lightweight distance bound protocol for low cost RFID tags. The proposed protocol based on modified version of Gossamer mutual authentication protocol. The implementation of the proposed protocol meets the limited abilities of low-cost RFID tags.

  15. Lightweight high temperature test furnace. 21st century technology

    Energy Technology Data Exchange (ETDEWEB)

    De Groot, F.C.

    2004-02-01

    A new high-temperature lightweight furnace design offers potential energy savings, thus reducing emissions and costs, and improves product quality. The Gasunie Research 12 m3 test furnace results are: 36% less heat needed to heat up the furnace; first tests show that 18% of flue gas heat loss is saved through pulse/pause firing; reduced carbon dioxide and gaseous hydrogen fluorides (HF) emissions; improved temperature homogeneity in product batch enables higher throughput; new dust-free combination of Refractory Ceramic Fibres (RCFs) have been tested successfully up to 1250C; new high-temperature vitreous wool (RCFs) with high solubility in body fluids and hence no hazard classification has been successfully tested; furnace control system developed and tested with good results, based on a standard industrial PLC, within stringent gas safety requirements.

  16. Optical Fibres Contactless Sensor for Dynamic Testing of Lightweight Structures

    Directory of Open Access Journals (Sweden)

    L. Bregant

    2008-01-01

    Full Text Available With dynamic testing, engineers describe activities focused on the identification of some properties of vibrating structures. This step requires for the measurements of excitations and responses signals, applying appropriate sensors directly on the test article. These instruments modify the system's mass and stiffness distributions and eventually the eigen-properties of the structure. These errors become unacceptable especially when testing lightweight structures. This paper shows the results of some tests performed on a small compressor with the purpose of identifying the blades’ natural frequencies and modes. It compares the acquisitions performed with standard accelerometers and two different contact-less systems using as exciters either a micro-hammer or a micro inertial shaker. The paper shows how the contact-less sensors provide good quality data and consistent results in the mode identification phase.

  17. An Ultra-Lightweight Encryption Scheme in Underwater Acoustic Networks

    Directory of Open Access Journals (Sweden)

    Chunyan Peng

    2016-01-01

    Full Text Available We tackle a fundamental security problem in underwater acoustic networks (UANs. The S-box in the existing block encryption algorithm is more energy consuming and unsuitable for resources-constrained UANs. In this paper, instead of S-box, we present a lightweight, 8-round iteration block cipher algorithm for UANs communication based on chaotic theory and increase the key space by changing the number of iteration round. We further propose secure network architecture of UANs. By analysis, our algorithm can resist brute-force searches and adversarial attacks. Simulation results show that, compared with traditional AES-128 and PRESENT algorithms, our cryptographic algorithm can make a good trade-off between security and overhead, has better energy efficiency, and applies to UANs.

  18. Image Encryption Using a Lightweight Stream Encryption Algorithm

    Directory of Open Access Journals (Sweden)

    Saeed Bahrami

    2012-01-01

    Full Text Available Security of the multimedia data including image and video is one of the basic requirements for the telecommunications and computer networks. In this paper, we consider a simple and lightweight stream encryption algorithm for image encryption, and a series of tests are performed to confirm suitability of the described encryption algorithm. These tests include visual test, histogram analysis, information entropy, encryption quality, correlation analysis, differential analysis, and performance analysis. Based on this analysis, it can be concluded that the present algorithm in comparison to A5/1 and W7 stream ciphers has the same security level, is better in terms of the speed of performance, and is used for real-time applications.

  19. A Lightweight Distributed Solution to Content Replication in Mobile Networks

    CERN Document Server

    La, Chi-Anh; Casetti, Claudio; Chiasserini, Carla-Fabiana; Fiore, Marco

    2009-01-01

    Performance and reliability of content access in mobile networks is conditioned by the number and location of content replicas deployed at the network nodes. Facility location theory has been the traditional, centralized approach to study content replication: computing the number and placement of replicas in a network can be cast as an uncapacitated facility location problem. The endeavour of this work is to design a distributed, lightweight solution to the above joint optimization problem, while taking into account the network dynamics. In particular, we devise a mechanism that lets nodes share the burden of storing and providing content, so as to achieve load balancing, and decide whether to replicate or drop the information so as to adapt to a dynamic content demand and time-varying topology. We evaluate our mechanism through simulation, by exploring a wide range of settings and studying realistic content access mechanisms that go beyond the traditional assumptionmatching demand points to their closest con...

  20. AEGIS: A Lightweight Firewall for Wireless Sensor Networks

    Science.gov (United States)

    Hossain, Mohammad Sajjad; Raghunathan, Vijay

    Firewalls are an essential component in today's networked computing systems (desktops, laptops, and servers) and provide effective protection against a variety of over-the-network security attacks. With the development of technologies such as IPv6 and 6LoWPAN that pave the way for Internet-connected embedded systems and sensor networks, these devices will soon be subject to (and need to be defended against) similar security threats. As a first step, this paper presents Aegis, a lightweight, rule-based firewall for networked embedded systems such as wireless sensor networks. Aegis is based on a semantically rich, yet simple, rule definition language. In addition, Aegis is highly efficient during operation, runs in a transparent manner from running applications, and is easy to maintain. Experimental results obtained using real sensor nodes and cycle-accurate simulations demonstrate that Aegis successfully performs gatekeeping of a sensor node's communication traffic in a flexible manner with minimal overheads.

  1. Properties of lightweight cement-based composites containing waste polypropylene

    Science.gov (United States)

    Záleská, Martina; Pavlíková, Milena; Pavlík, Zbyšek

    2016-07-01

    Improvement of buildings thermal stability represents an increasingly important trend of the construction industry. This work aims to study the possible use of two types of waste polypropylene (PP) for the development of lightweight cement-based composites with enhanced thermal insulation function. Crushed PP waste originating from the PP tubes production is used for the partial replacement of silica sand by 10, 20, 30, 40 and 50 mass%, whereas a reference mixture without plastic waste is studied as well. First, basic physical and thermal properties of granular PP random copolymer (PPR) and glass fiber reinforced PP (PPGF) aggregate are studied. For the developed composite mixtures, basic physical, mechanical, heat transport and storage properties are accessed. The obtained results show that the composites with incorporated PP aggregate exhibit an improved thermal insulation properties and acceptable mechanical resistivity. This new composite materials with enhanced thermal insulation function are found to be promising materials for buildings subsoil or floor structures.

  2. A Lightweight Approach to Performance Portability with targetDP

    CERN Document Server

    Gray, Alan

    2016-01-01

    Leading HPC systems achieve their status through use of highly parallel devices such as NVIDIA GPUs or Intel Xeon Phi many-core CPUs. The concept of performance portability across such architectures, as well as traditional CPUs, is vital for the application programmer. In this paper we describe targetDP, a lightweight abstraction layer which allows grid-based applications to target data parallel hardware in a platform agnostic manner. We demonstrate the effectiveness of our pragmatic approach by presenting performance results for a complex fluid application (with which the model was co-designed), plus a separate lattice QCD particle physics code. For each application, a single source code base is seen to achieve portable performance, as assessed within the context of the Roofline model. TargetDP can be combined with MPI to allow use on systems containing multiple nodes: we demonstrate this through provision of scaling results on traditional and GPU-accelerated large scale supercomputers.

  3. Light-Weight Injector Technology for Cryogenic Mars Ascent Engines

    Science.gov (United States)

    Trihn, Huu Phuoc; Cramer, John M.

    1998-01-01

    Preliminary mission studies for human exploration of Mars have been performed at Marshall Space Flight Center (MSFC). These studies indicate that for chemical rockets only a cryogenic propulsion system would provide high enough performance to be considered for a Mars ascent vehicle. Although the mission is possible with Earth-supplied propellants for this vehicle, utilization of in-situ propellants is highly attractive. This option would significantly reduce the overall mass of launch vehicles. Consequently, the cost of the mission would be greatly reduced because the number and size of the Earth launch vehicle(s) needed for the mission decrease. NASA/Johnson Space Center has initiated several concept studies of in-situ propellant production plants. Liquid oxygen (LOX) is the primary candidate for an in-situ oxidizer. In-situ fuel candidates include methane (CH4), ethylene (C2H4), and methanol (CH3OH). MSFC initiated a technology development program for a cryogenic propulsion system for the Mars human exploration mission in 1998. One part of this technology program is the effort described here: an evaluation of propellant injection concepts for a LOX/liquid methane Mars Ascent Engine (MAE) with an emphasis on light-weight, high efficiency, reliability, and thermal compatibility. In addition to the main objective, hot-fire tests of the subject injectors will be used to test other key technologies including light-weight combustion chamber materials and advanced ignition concepts. This state-of-the-art technology will then be applied to the development of a cryogenic propulsion system that will meet the requirements of the planned Mars sample return (MSR) mission. The current baseline propulsion system for the MSR mission uses a storable propellant combination [monomethyl hydrazine/mixed oxides of nitrogen-25. However, a mission option that incorporates in-situ propellant production and utilization for the ascent stage is being carefully considered as a subscale

  4. Lightweight High Efficiency Electric Motors for Space Applications

    Science.gov (United States)

    Robertson, Glen A.; Tyler, Tony R.; Piper, P. J.

    2011-01-01

    Lightweight high efficiency electric motors are needed across a wide range of space applications from - thrust vector actuator control for launch and flight applications to - general vehicle, base camp habitat and experiment control for various mechanisms to - robotics for various stationary and mobile space exploration missions. QM Power?s Parallel Path Magnetic Technology Motors have slowly proven themselves to be a leading motor technology in this area; winning a NASA Phase II for "Lightweight High Efficiency Electric Motors and Actuators for Low Temperature Mobility and Robotics Applications" a US Army Phase II SBIR for "Improved Robot Actuator Motors for Medical Applications", an NSF Phase II SBIR for "Novel Low-Cost Electric Motors for Variable Speed Applications" and a DOE SBIR Phase I for "High Efficiency Commercial Refrigeration Motors" Parallel Path Magnetic Technology obtains the benefits of using permanent magnets while minimizing the historical trade-offs/limitations found in conventional permanent magnet designs. The resulting devices are smaller, lower weight, lower cost and have higher efficiency than competitive permanent magnet and non-permanent magnet designs. QM Power?s motors have been extensively tested and successfully validated by multiple commercial and aerospace customers and partners as Boeing Research and Technology. Prototypes have been made between 0.1 and 10 HP. They are also in the process of scaling motors to over 100kW with their development partners. In this paper, Parallel Path Magnetic Technology Motors will be discussed; specifically addressing their higher efficiency, higher power density, lighter weight, smaller physical size, higher low end torque, wider power zone, cooler temperatures, and greater reliability with lower cost and significant environment benefit for the same peak output power compared to typically motors. A further discussion on the inherent redundancy of these motors for space applications will be provided.

  5. ExternE transport methodology for external cost evaluation of air pollution

    DEFF Research Database (Denmark)

    Jensen, S. S.; Berkowicz, R.; Brandt, J.

    The report describes how the human exposure estimates based on NERI's human exposure modelling system (AirGIS) can improve the Danish data used for exposure factors in the ExternE Transport methodology. Initially, a brief description of the ExternE Tranport methodology is given and it is summaris...

  6. The External Mind

    DEFF Research Database (Denmark)

    The External Mind: an Introduction by Riccardo Fusaroli, Claudio Paolucci pp. 3-31 The sign of the Hand: Symbolic Practices and the Extended Mind by Massimiliano Cappuccio, Michael Wheeler pp. 33-55 The Overextended Mind by Shaun Gallagher pp. 57-68 The "External Mind": Semiotics, Pragmatism......, Extended Mind and Distributed Cognition by Claudio Paolucci pp. 69-96 The Social Horizon of Embodied Language and Material Symbols by Riccardo Fusaroli pp. 97-123 Semiotics and Theories of Situated/Distributed Action and Cognition: a Dialogue and Many Intersections by Tommaso Granelli pp. 125-167 Building...... Action in Public Environments with Diverse Semiotic Resources by Charles Goodwin pp. 169-182 How Marking in Dance Constitutes Thinking with the Body by David Kirsh pp. 183-214 Ambiguous Coordination: Collaboration in Informal Science Education Research by Ivan Rosero, Robert Lecusay, Michael Cole pp. 215-240...

  7. External-Memory Multimaps

    CERN Document Server

    Angelino, Elaine; Mitzenmacher, Michael; Thaler, Justin

    2011-01-01

    Many data structures support dictionaries, also known as maps or associative arrays, which store and manage a set of key-value pairs. A \\emph{multimap} is generalization that allows multiple values to be associated with the same key. For example, the inverted file data structure that is used prevalently in the infrastructure supporting search engines is a type of multimap, where words are used as keys and document pointers are used as values. We study the multimap abstract data type and how it can be implemented efficiently online in external memory frameworks, with constant expected I/O performance. The key technique used to achieve our results is a combination of cuckoo hashing using buckets that hold multiple items with a multiqueue implementation to cope with varying numbers of values per key. Our external-memory results are for the standard two-level memory model.

  8. Assessing resolution in super-resolution imaging.

    Science.gov (United States)

    Demmerle, Justin; Wegel, Eva; Schermelleh, Lothar; Dobbie, Ian M

    2015-10-15

    Resolution is a central concept in all imaging fields, and particularly in optical microscopy, but it can be easily misinterpreted. The mathematical definition of optical resolution was codified by Abbe, and practically defined by the Rayleigh Criterion in the late 19th century. The limit of conventional resolution was also achieved in this period, and it was thought that fundamental constraints of physics prevented further increases in resolution. With the recent development of a range of super-resolution techniques, it is necessary to revisit the concept of optical resolution. Fundamental differences in super-resolution modalities mean that resolution is not a directly transferrable metric between techniques. This article considers the issues in resolution raised by these new technologies, and presents approaches for comparing resolution between different super-resolution methods.

  9. Architectural Engineering to Super-Light Structures

    DEFF Research Database (Denmark)

    Castberg, Niels Andreas

    with architectural engineering as a starting point. The thesis is based on a two stringed hypothesis: Architectural engineering gives rise to better architecture and Super-Light Structures support and enables a static, challenging architecture. The aim of the thesis is to clarify architectural engineering's impact...... on the work process between architects and engineers in the design development. Using architectural engineering, Super-Light Structures are examined in an architectural context, and it is explained how digital tools can support architectural engineering and design of Super-Light Structures. The experiences...... to be subjects of examination for this thesis. The research results show that architectural engineering has a significant impact on a design process. The projects illustrate that simple explanations, underpinned by visualisations of the challenges between shape versus structure, often creates a shared...

  10. Breeding Super-Earths and Birthing Super-Puffs in Transitional Disks

    CERN Document Server

    Lee, Eve J

    2015-01-01

    The riddle posed by super-Earths (1-4$R_\\oplus$, 2-20$M_\\oplus$) is that they are not Jupiters: their core masses are large enough to trigger runaway gas accretion, yet somehow super-Earths accreted atmospheres that weigh only a few percent of their total mass. We show that this puzzle is solved if super-Earths formed late, as the last vestiges of their parent gas disks were about to clear. This scenario would seem to present fine-tuning problems, but we show that there are none. Ambient gas densities can span many (up to 9) orders of magnitude, and super-Earths can still robustly emerge after $\\sim$0.1-1 Myr with percent-by-weight atmospheres. Super-Earth cores are naturally bred in gas-poor environments where gas dynamical friction has weakened sufficiently to allow constituent protocores to merge. So little gas is present at the time of core assembly that cores hardly migrate by disk torques: formation of super-Earths can be in situ. The picture --- that close-in super-Earths form in a gas-poor (but not ga...

  11. Eyeglass Large Aperture, Lightweight Space Optics FY2000 - FY2002 LDRD Strategic Initiative

    Energy Technology Data Exchange (ETDEWEB)

    Hyde, R

    2003-02-10

    differences in their requirements and implementations, the fundamental difficulty in utilizing large aperture optics is the same for all of these applications: It is extremely difficult to design large aperture space optics which are both optically precise and can meet the practical requirements for launch and deployment in space. At LLNL we have developed a new concept (Eyeglass) which uses large diffractive optics to solve both of these difficulties; greatly reducing both the mass and the tolerance requirements for large aperture optics. During previous LDRD-supported research, we developed this concept, built and tested broadband diffractive telescopes, and built 50 cm aperture diffraction-limited diffractive lenses (the largest in the world). This work is fully described in UCRL-ID-136262, Eyeglass: A Large Aperture Space Telescope. However, there is a large gap between optical proof-of-principle with sub-meter apertures, and actual 50 meter space telescopes. This gap is far too large (both in financial resources and in spacecraft expertise) to be filled internally at LLNL; implementation of large aperture diffractive space telescopes must be done externally using non-LLNL resources and expertise. While LLNL will never become the primary contractor and integrator for large space optical systems, our natural role is to enable these devices by developing the capability of producing very large diffractive optics. Accordingly, the purpose of the Large Aperture, Lightweight Space Optics Strategic Initiative was to develop the technology to fabricate large, lightweight diffractive lenses. The additional purpose of this Strategic Initiative was, of course, to demonstrate this lens-fabrication capability in a fashion compellingly enough to attract the external support necessary to continue along the path to full-scale space-based telescopes. During this 3 year effort (FY2000-FY2002) we have developed the capability of optically smoothing and diffractively-patterning thin meter

  12. External conference: Geneva University

    CERN Multimedia

    2006-01-01

    Ecole de physique Département de physique nucléaire et corspusculaire 24, Quai Ernest-Ansermet 1211 GENEVE 4 Tél: (022) 379 62 73 Fax: (022) 379 69 92 Wednesday 13 December 2006 PARTICLE PHYSICS SEMINAR at 17.00 hrs - Stückelberg Auditorium Radiation Tolerant Sensors for Solid State Tracking Detectors by Dr Michael MOLL / CERN The envisaged upgrade of the Large Hadron Collider (LHC) at CERN towards the Super-LHC (SLHC) with a 10 times increased luminosity of 1035 cm2 s-1 will present severe challenges for the tracking detectors of the SLHC experiments. Unprecedented high radiation levels and track densities and a reduced bunch crossing time in the order of 10 ns as well as the need for cost effective detectors have called for an intensive R&D program. The CERN RD50 collaboration 'Development of Radiation Hard Semiconductor Devices for Very High Luminosity Colliders' is working on the development of semiconductor sensors matching the requirements of the SLHC. Sensors based on defect engineered silic...

  13. Conserved role of unc-79 in ethanol responses in lightweight mutant mice.

    Directory of Open Access Journals (Sweden)

    David J Speca

    2010-08-01

    Full Text Available The mechanisms by which ethanol and inhaled anesthetics influence the nervous system are poorly understood. Here we describe the positional cloning and characterization of a new mouse mutation isolated in an N-ethyl-N-nitrosourea (ENU forward mutagenesis screen for animals with enhanced locomotor activity. This allele, Lightweight (Lwt, disrupts the homolog of the Caenorhabditis elegans (C. elegans unc-79 gene. While Lwt/Lwt homozygotes are perinatal lethal, Lightweight heterozygotes are dramatically hypersensitive to acute ethanol exposure. Experiments in C. elegans demonstrate a conserved hypersensitivity to ethanol in unc-79 mutants and extend this observation to the related unc-80 mutant and nca-1;nca-2 double mutants. Lightweight heterozygotes also exhibit an altered response to the anesthetic isoflurane, reminiscent of unc-79 invertebrate mutant phenotypes. Consistent with our initial mapping results, Lightweight heterozygotes are mildly hyperactive when exposed to a novel environment and are smaller than wild-type animals. In addition, Lightweight heterozygotes exhibit increased food consumption yet have a leaner body composition. Interestingly, Lightweight heterozygotes voluntarily consume more ethanol than wild-type littermates. The acute hypersensitivity to and increased voluntary consumption of ethanol observed in Lightweight heterozygous mice in combination with the observed hypersensitivity to ethanol in C. elegans unc-79, unc-80, and nca-1;nca-2 double mutants suggests a novel conserved pathway that might influence alcohol-related behaviors in humans.

  14. Super-Period Gold Nanodisc Grating-Enabled Surface Plasmon Resonance Spectrometer Sensor.

    Science.gov (United States)

    Tian, Xueli; Guo, Hong; Bhatt, Ketan H; Zhao, Song Q; Wang, Yi; Guo, Junpeng

    2015-10-01

    We experimentally demonstrate a surface plasmon resonance spectrometer sensor by using an e-beam-patterned super-period gold nanodisc grating on a glass substrate. The super-period gold nanodisc grating has a small subwavelength period and a large diffraction grating period. The small subwavelength period enhances localized surface plasmon resonance, and the large diffraction grating period diffracts surface plasmon resonance radiation into different directions corresponding to different wavelengths. Surface plasmon resonance spectra are measured in the first order diffraction spatial profiles captured by a charge-coupled device (CCD) in addition to the traditional way of measurement using an external optical spectrometer in the zeroth order transmission. A surface plasmon resonance sensor for the bovine serum albumin protein nanolayer bonding is demonstrated by measuring the surface plasmon resonance shift in the first order diffraction spatial intensity profiles captured by the CCD.

  15. KML Super Overlay to WMS Translator

    Science.gov (United States)

    Plesea, Lucian

    2007-01-01

    This translator is a server-based application that automatically generates KML super overlay configuration files required by Google Earth for map data access via the Open Geospatial Consortium WMS (Web Map Service) standard. The translator uses a set of URL parameters that mirror the WMS parameters as much as possible, and it also can generate a super overlay subdivision of any given area that is only loaded when needed, enabling very large areas of coverage at very high resolutions. It can make almost any dataset available as a WMS service visible and usable in any KML application, without the need to reformat the data.

  16. Super-resolution optical microscopy: multiple choices.

    Science.gov (United States)

    Huang, Bo

    2010-02-01

    The recent invention of super-resolution optical microscopy enables the visualization of fine features in biological samples with unprecedented clarity. It creates numerous opportunities in biology because vast amount of previously obscured subcellular processes now can be directly observed. Rapid development in this field in the past two years offers many imaging modalities that address different needs but they also complicates the choice of the 'perfect' method for answering a specific question. Here I will briefly describe the principles of super-resolution optical microscopy techniques and then focus on comparing their characteristics in various aspects of practical applications.

  17. Super resolution of images and video

    CERN Document Server

    Katsaggelos, Aggelos K

    2007-01-01

    This book focuses on the super resolution of images and video. The authors' use of the term super resolution (SR) is used to describe the process of obtaining a high resolution (HR) image, or a sequence of HR images, from a set of low resolution (LR) observations. This process has also been referred to in the literature as resolution enhancement (RE). SR has been applied primarily to spatial and temporal RE, but also to hyperspectral image enhancement. This book concentrates on motion based spatial RE, although the authors also describe motion free and hyperspectral image SR problems. Also exa

  18. Super-Laplacians and their symmetries

    Science.gov (United States)

    Howe, P. S.; Lindström, U.

    2017-05-01

    A super-Laplacian is a set of differential operators in superspace whose highestdimensional component is given by the spacetime Laplacian. Symmetries of super-Laplacians are given by linear differential operators of arbitrary finite degree and are determined by superconformal Killing tensors. We investigate these in flat superspaces. The differential operators determining the symmetries give rise to algebras which can be identified in many cases with the tensor algebras of the relevant superconformal Lie algebras modulo certain ideals. They have applications to Higher Spin theories.

  19. Preliminary vibration, acoustic, and shock design and test criteria for components on the Lightweight External Tank (LWT)

    Science.gov (United States)

    1981-01-01

    The Space Shuttle LWT is divided into zones and subzones. Zones are designated primarily to assist in determining the applicable specifications. A subzone (general Specification) is available for use when the location of the component is known but component design and weight are not well defined. When the location, weight, and mounting configuration of the component are known, specifications for appropriate subzone weight ranges are available. Along with the specifications are vibration, acoustic, shock, transportation, handling, and acceptance test requirements and procedures. A method of selecting applicable vibration, acoustic, and shock specifications is presented.

  20. New method for making super-plastic glasses

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ It was a long-cherished dream for materials scientists to find a nearly ideal metallic alloy with high strength and super-plasticity concurrently as a super-material both extremely strong and exceptionally hard for human use.

  1. Second invariant for two-dimensional classical super systems

    Indian Academy of Sciences (India)

    S C Mishra; Roshan Lal; Veena Mishra

    2003-10-01

    Construction of superpotentials for two-dimensional classical super systems (for ≥ 2) is carried out. Some interesting potentials have been studied in their super form and also their integrability.

  2. An integrable generalization of the super AKNS hierarchy and its bi-Hamiltonian formulation

    Science.gov (United States)

    Yu, Jing; Ma, Wen-Xiu; Han, Jingwei; Chen, Shouting

    2017-02-01

    Based on a Lie super-algebra B(0, 1), an integrable generalization of the super AKNS iso-spectral problem is introduced and its corresponding generalized super AKNS hierarchy is generated. By making use of the super-trace identity (or the super variational identity), the resulting super soliton hierarchy can be put into a super bi-Hamiltonian form. A generalized super AKNS soliton hierarchy with self-consistent sources is also presented.

  3. Lightweight design and finite element analysis of primary mirror for the space telescope

    Science.gov (United States)

    Zhang, Dandan; Li, Weiyan; Lv, Qunbo; Liu, Yangyang; Chen, Xinwen

    2015-09-01

    In order to satisfy the strict requirements of the lightweight ratios and high dimensional stability for space mirror, the design method of lightweight structure and the flexible supporting structure of the primary mirror is proposed. Subsequently, the surface deformations of two different lightweight structures for primary mirror are discussed for analyzing the influence of the mirror weight on its surface. Finally, the finite element models for primary mirror assembly are built for calculating the surface deformation caused by different gravity orientations and various thermal environments. It is proved that the weight, stiffness and surface accuracy of the structure design for primary mirror can meet the engineering requirement.

  4. A Specialized Lightweight Metamorphic Function for KASUMI Metamorphic Cipher and Its FPGA Implementation

    Directory of Open Access Journals (Sweden)

    Rabie A. Mahmoud

    2016-08-01

    Full Text Available To enhance the performance of the KASUMI Metamorphic Cipher, we apply a lightweight Metamorphic Structure. The proposed structure uses four lightweight bit-balanced operations in the function Meta-FO of the KASUMI Metamorphic Cipher. These operations are: XOR, INV, XNOR, and NOP for bitwise XOR, invert, XNOR, and no operation respectively building blocks of the Specialized Crypto Logic Unit (SCLU. In this work, we present a lightweight KASUMI Specialized-Metamorphic Cipher. In addition, we provide a Field Programmable Gate Array (FPGA implementation of the proposed algorithm modification.

  5. Project CONDOR: Middle atmosphere wind structure obtained with lightweight inflatable spheres near the equatorial electrojet

    Science.gov (United States)

    Schmidlin, F. J.

    1987-01-01

    Observed correlations between the atmospheric electric field and the neutral wind were studied using additional atmospheric measurements during Project CONDOR. Project CONDOR obtained measurements near the equatorial electrojet (12 S) during March 1983. Neutral atmosphere wind measurements were obtained using lightweight inflatable spheres and temperatures were obtained using a datasonde. The lightweight sphere technology, the wind structure, and temperature structure are described. Results show that the lightweight sphere gives higher vertical resolution of winds below 75 km compared with the standard sphere, but gives little or no improvement above 80 km, and no usable temperature and density data.

  6. M-FILE FOR MIX DESIGN OF STRUCTURAL LIGHTWEIGHT CONCRETE USING DEVELOPED MODELS

    Directory of Open Access Journals (Sweden)

    M. ABDULLAHI

    2011-08-01

    Full Text Available An m-file for mix design of structural lightweight concrete is presented. Mix design of structural lightweight concrete is conducted using guide in the standards. This may be tasking involving reading and understanding of the relevant standards. This renders the process inefficient and liable to errors in computations. A computer approach to mix design will alleviate this problem. An m-file was developed in MATLAB environment for the concrete mix design. The m-file has been tested and has proved to be efficient in computing the mix composition for the first trial batch of lightweight concrete mixes. It can also perform concrete mixture proportioning adjustment.

  7. Explosive Super-eruptions: Problems and Prejudices

    Science.gov (United States)

    Self, S.

    2010-12-01

    A super-eruption is defined as one with a magma yield > 10^15 kg (magnitude (M) 8). The term has mainly been applied to large-scale, caldera and ignimbrite-forming explosive eruptions, but it can be applied to all eruptions that released > 10^15 kg of magma. For effusive volcanism, evidence suggests that individual eruptions of this size ( > ~ 370 km^3 of typical basalt or > 450 km^3 of rhyolite flood lava) arise only during periods of LIP formation. The super-eruption concept raises interesting questions about genesis and storage of magmas that feed these vast events. Deposits of major explosive eruptions are Plinian fallout, ignimbrite sheets, and co-ignimbrite ash fall. Based on earlier suggestions and evidence, widespread outflow ignimbrite (O), co-ignimbrite ash (A), and inter-caldera ignimbrite (I) are all major components of the total super-eruption deposit and may tend towards being subequal. In super-eruption deposits, the reported volume of vent-derived Plinian eruption column fallout is often a minor component of the total volume, yet in several cases (Oruanui, Taupo, 26 ka ago, M 8.1; Bishop Tuff, 760 ka, M 8.2; Bandelier (Otowi) Tuff, 1.6 Ma, M8) it is now recognized that vent-derived columns persisted for most of the eruption. Thus, distally, the ash-fall derived from co-ignimbrite ash clouds may be mixed with contemporaneous fallout from a vertical column. Some major ignimbrites have no reported associated Plinian deposit; the huge Young Toba Tuff (YTT, 74 ka, M 8.8) is a significant example. However, the very widespread Toba ash-fall deposit constitutes ~ 40 % of the total mass of magma erupted and is presumed to be co-ignimbrite. Timing of the onset of column collapse probably controls whether a recognizable Plinian deposit is laid down. All super-eruptions probably produce extensive fallout deposits, and this is generally of vent-derived and pyroclastic-flow-derived origin. Establishing the relationships between large-scale ignimbrites and their

  8. On super edge-graceful trees of diameter four

    CERN Document Server

    Krop, E; Raridan, C

    2011-01-01

    In "On the super edge graceful trees of even orders," Chung, Lee, Gao, and Schaffer posed the following problem: Characterize trees of diameter 4 which are super edge-graceful. In this paper, we provide super edge-graceful labelings for all caterpillars and even size lobsters of diameter 4 which permit such labelings. We also provide super edge-graceful labelings for several families of odd size lobsters of diameter 4.

  9. The structure of the super-W∞(λ) algebra

    NARCIS (Netherlands)

    Bergshoeff, E.; Wit, B. de; Vasiliev, M.

    1991-01-01

    We give a comprehensive treatment of the super-W∞(λ) algebra, an extension of the super-Virasoro algebra that contains generators of spin s ≥ ½. The parameter λ defines the embedding of the Virasoro subalgebra. We describe how to obtain the super-W∞(λ) algebra from the associative algebra of

  10. Regularization by External Variables

    DEFF Research Database (Denmark)

    Bossolini, Elena; Edwards, R.; Glendinning, P. A.

    2016-01-01

    Regularization was a big topic at the 2016 CRM Intensive Research Program on Advances in Nonsmooth Dynamics. There are many open questions concerning well known kinds of regularization (e.g., by smoothing or hysteresis). Here, we propose a framework for an alternative and important kind of regula...... of regularization, by external variables that shadow either the state or the switch of the original system. The shadow systems are derived from and inspired by various applications in electronic control, predator-prey preference, time delay, and genetic regulation....

  11. Super ready: how a regional approach to Super Bowl EMS paid off.

    Science.gov (United States)

    Clancy, Terry; Cortacans, Henry P

    2014-07-01

    The Super Bowl and its associated activities represent one of the largest special events in the world. Super Bowl XLVIII was geographically unique because the NFL's and Super Bowl Host Committee's activities, venues and events encompassed two states and fell across numerous jurisdictions within six counties (Bergen, Hudson, Morris, Essex, Middlesex, and Manhattan).This Super Bowl was the first to do this. EMS was one of the largest operational components during this event. Last and most important, it is the people and relationships that make any planning initiative and event a success. Sit down and have a cup a coffee with your colleagues, partners and neighbors in and out of state to discuss your planning initiatives. Do it early-it will make your efforts less painful should an event of this magnitude come to a city near you!

  12. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  13. Acoustic Design of Super-light Structures

    DEFF Research Database (Denmark)

    Christensen, Jacob Ellehauge; Hertz, Kristian Dahl; Brunskog, Jonas

    aggregate (leca) along with a newly developed technology called pearl-chain reinforcement, which is a system for post-tensioning. Here, it is shown how to combine these technologies within a precast super-light slab element, while honoring the requirements of a holistic design. Acoustic experiments...

  14. Folded shapes with Super-Light Structures

    DEFF Research Database (Denmark)

    Castberg, Niels Andreas; Hertz, Kristian Dahl

    2012-01-01

    The use of folded shapes in structures has become more common, but it still costs problems because of construction issues and bending moments. The present paper deals with how the newly patented structural concept Super-Light structures (SLS) can be used to create folded shapes. SLS gives lighter...

  15. Single Image Super Resolution via Sparse Reconstruction

    NARCIS (Netherlands)

    Kruithof, M.C.; Eekeren, A.W.M. van; Dijk, J.; Schutte, K.

    2012-01-01

    High resolution sensors are required for recognition purposes. Low resolution sensors, however, are still widely used. Software can be used to increase the resolution of such sensors. One way of increasing the resolution of the images produced is using multi-frame super resolution algorithms. Limita

  16. Conformal anomaly of super Wilson loop

    Energy Technology Data Exchange (ETDEWEB)

    Belitsky, A.V., E-mail: andrei.belitsky@asu.edu [Department of Physics, Arizona State University, Tempe, AZ 85287-1504 (United States)

    2012-09-11

    Classically supersymmetric Wilson loop on a null polygonal contour possesses all symmetries required to match it onto non-MHV amplitudes in maximally supersymmetric Yang-Mills theory. However, to define it quantum mechanically, one is forced to regularize it since perturbative loop diagrams are not well defined due to presence of ultraviolet divergences stemming from integration in the vicinity of the cusps. A regularization that is adopted by practitioners by allowing one to use spinor helicity formalism, on the one hand, and systematically go to higher orders of perturbation theory is based on a version of dimensional regularization, known as Four-Dimensional Helicity scheme. Recently it was demonstrated that its use for the super Wilson loop at one loop breaks both conformal symmetry and Poincare supersymmetry. Presently, we exhibit the origin for these effects and demonstrate how one can undo this breaking. The phenomenon is alike the one emerging in renormalization group mixing of conformal operators in conformal theories when one uses dimensional regularization. The rotation matrix to the diagonal basis is found by means of computing the anomaly in the Ward identity for the conformal boost. Presently, we apply this ideology to the super Wilson loop. We compute the one-loop conformal anomaly for the super Wilson loop and find that the anomaly depends on its Grassmann coordinates. By subtracting this anomalous contribution from the super Wilson loop we restore its interpretation as a dual description for reduced non-MHV amplitudes which are expressed in terms of superconformal invariants.

  17. Super-Kamiokande worth full restoration

    CERN Multimedia

    Mishima, I

    2002-01-01

    While prospects are good that the SuperKamiokande facility will be partially repaired after an accident last November, the government has yet to confirm whether it will spend the estimated 2.5 billion yen needed for a full-scale restoration (1 page).

  18. Structural optimization of super-repellent surfaces

    DEFF Research Database (Denmark)

    Cavalli, Andrea; Bøggild, Peter; Okkels, Fridolin

    2013-01-01

    Micro-patterning is an effective way to achieve surfaces with extreme liquid repellency. This technique does not rely on chemical coatings and is therefore a promising concept for application in food processing and bio-compatibile coatings. This super-repellent behaviour is obtained by suspending...

  19. Facile preparation of super durable superhydrophobic materials.

    Science.gov (United States)

    Wu, Lei; Zhang, Junping; Li, Bucheng; Fan, Ling; Li, Lingxiao; Wang, Aiqin

    2014-10-15

    The low stability, complicated and expensive fabrication procedures seriously hinder practical applications of superhydrophobic materials. Here we report an extremely simple method for preparing super durable superhydrophobic materials, e.g., textiles and sponges, by dip coating in fluoropolymers (FPs). The morphology, surface chemical composition, mechanical, chemical and environmental stabilities of the superhydrophobic textiles were investigated. The results show how simple the preparation of super durable superhydrophobic textiles can be! The superhydrophobic textiles outperform their natural counterparts and most of the state-of-the-art synthetic superhydrophobic materials in stability. The intensive mechanical abrasion, long time immersion in various liquids and repeated washing have no obvious influence on the superhydrophobicity. Water drops are spherical in shape on the samples and could easily roll off after these harsh stability tests. In addition, this simple dip coating approach is applicable to various synthetic and natural textiles and can be easily scaled up. Furthermore, the results prove that a two-tier roughness is helpful but not essential with regard to the creation of super durable superhydrophobic textiles. The combination of microscale roughness of textiles and materials with very low surface tension is enough to form super durable superhydrophobic textiles. According to the same procedure, superhydrophobic polyurethane sponges can be prepared, which show high oil absorbency, oil/water separation efficiency and stability. Copyright © 2014 Elsevier Inc. All rights reserved.

  20. Pavement behaviour under the super single tyre

    CSIR Research Space (South Africa)

    Viljoen, AW

    1982-06-01

    Full Text Available Pavement behaviour under the super single tyre (SST) was investigated and compared with that under a conventional dual tyre (CDT). Contact areas and contact pressures over a range of loading conditions were measured and compared. Two approaches were...

  1. Typhoon effects on super-tall buildings

    Science.gov (United States)

    Li, Q. S.; Xiao, Y. Q.; Wu, J. R.; Fu, J. Y.; Li, Z. N.

    2008-06-01

    Full-scale measurement is considered to be the most reliable method for evaluating wind effects on buildings and structures. This paper presents selected results of wind characteristics and structural responses measured from four super-tall buildings, The Center (350 m high, 79 floors) in Hong Kong, Di Wang Tower (384 m high, 78 floors) in Shenzhen, CITIC Plaza Tower (391 m high, 80 floors) in Guangzhou and Jin Mao Building (421 m high, 88 floors) in Shanghai, during the passages of three typhoons. The field data such as wind speed, wind direction and acceleration responses, etc., were continuously measured from the super-tall buildings during the typhoons. Detailed analysis of the field data was conducted to investigate the characteristics of typhoon-generated wind and wind-induced vibrations of these super-tall buildings under typhoon conditions. The dynamic characteristics of the tall buildings were determined from the field measurements and comparisons with those calculated from the finite element (FE) models of the structures were made. Furthermore, the full-scale measurements were compared with wind tunnel results to evaluate the accuracy of the model test results and the adequacy of the techniques used in the wind tunnel tests. The results presented in this paper are expected to be of considerable interest and of use to researchers and professionals involved in designing super-tall buildings.

  2. Searching for Frozen Super Earth via Microlensing

    Science.gov (United States)

    Batista, V.; Beaulieu, J. P.; Cassan, A.; Coutures, C.; Donatowicz, J.; Fouqué, P.; Kubas, D.; Marquette, J. B.

    2009-04-01

    Microlensing planet hunt is a unique method to probe efficiently for frozen Super Earth orbiting the most common stars of our galaxy. It is nicely complementing the parameter space probed by very high accuracy radial velocity measurements and future space based detections of low mass transiting planets. In order to maximize the planet catch, the microlensing community is engaged in a total cooperation among the different groups (OGLE, MicroFUN, MOA, PLANET/RoboNET) by making the real time data available, and mutual informing/reporting about modeling efforts. Eight planets have been published so far by combinations of the different groups, 4 Jovian analogues, one Neptune and two Super Earth. Given the microlensing detection efficiency, it suggests that these Neptunes/Super Earths may be quite common. Using networks of dedicated 1-2m class telescopes, the microlensing community has entered a new phase of planet discoveries, and will be able to provide constraints on the abundance of frozen Super-Earths in the near future. Statistics about Mars to Earth mass planets, extending to the habitable zone will be achieved with space based wide field imagers (EUCLID) at the horizon 2017.

  3. Folded shapes with Super-Light Structures

    DEFF Research Database (Denmark)

    Castberg, Niels Andreas; Hertz, Kristian Dahl

    2012-01-01

    The use of folded shapes in structures has become more common, but it still costs problems because of construction issues and bending moments. The present paper deals with how the newly patented structural concept Super-Light structures (SLS) can be used to create folded shapes. SLS gives lighter...

  4. Advantages of super-light structures

    DEFF Research Database (Denmark)

    Hertz, Kristian Dahl

    2009-01-01

    Super-light structures with pearl-chain reinforcement is a new revolutionary technology that opens possibilities of building load-bearing structures much cheaper and with several other advantages compared to traditional constructions of concrete and steel. Some benefits are: 1 Half price or less. 2...

  5. Super-resolution near field imaging device

    DEFF Research Database (Denmark)

    2014-01-01

    Super-resolution imaging device comprising at least a first and a second elongated coupling element, each having a first transverse dimension at a first end and a second transverse dimension at a second end and being adapted for guiding light between their respective first and second ends, each...

  6. BREEDING SUPER-EARTHS AND BIRTHING SUPER-PUFFS IN TRANSITIONAL DISKS

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Eve J.; Chiang, Eugene, E-mail: evelee@berkeley.edu, E-mail: echiang@astro.berkeley.edu [Department of Astronomy, University of California Berkeley, Berkeley, CA 94720-3411 (United States)

    2016-02-01

    The riddle posed by super-Earths (1–4R{sub ⊕}, 2–20M{sub ⊕}) is that they are not Jupiters: their core masses are large enough to trigger runaway gas accretion, yet somehow super-Earths accreted atmospheres that weigh only a few percent of their total mass. We show that this puzzle is solved if super-Earths formed late, as the last vestiges of their parent gas disks were about to clear. This scenario would seem to present fine-tuning problems, but we show that there are none. Ambient gas densities can span many (in one case up to 9) orders of magnitude, and super-Earths can still robustly emerge after ∼0.1–1 Myr with percent-by-weight atmospheres. Super-Earth cores are naturally bred in gas-poor environments where gas dynamical friction has weakened sufficiently to allow constituent protocores to gravitationally stir one another and merge. So little gas is present at the time of core assembly that cores hardly migrate by disk torques: formation of super-Earths can be in situ. The basic picture—that close-in super-Earths form in a gas-poor (but not gas-empty) inner disk, fed continuously by gas that bleeds inward from a more massive outer disk—recalls the largely evacuated but still accreting inner cavities of transitional protoplanetary disks. We also address the inverse problem presented by super-puffs: an uncommon class of short-period planets seemingly too voluminous for their small masses (4–10R{sub ⊕}, 2–6M{sub ⊕}). Super-puffs most easily acquire their thick atmospheres as dust-free, rapidly cooling worlds outside ∼1 AU where nebular gas is colder, less dense, and therefore less opaque. Unlike super-Earths, which can form in situ, super-puffs probably migrated in to their current orbits; they are expected to form the outer links of mean-motion resonant chains, and to exhibit greater water content. We close by confronting observations and itemizing remaining questions.

  7. SuperB A High-Luminosity Asymmetric $e^+ e^-$ Super Flavour Factory : Conceptual Design Report

    CERN Document Server

    Bona, M.; Grauges Pous, E.; Colangelo, P.; De Fazio, F.; Palano, A.; Manghisoni, M.; Re, V.; Traversi, G.; Eigen, G.; Venturini, M.; Soni, N.; Bruschi, M.; De Castro, S.; Faccioli, P.; Gabrieli, A.; Giacobbe, B.; Semprini Cesare, N.; Spighi, R.; Villa, M.; Zoccoli, A.; Hearty, C.; McKenna, J.; Soni, A.; Khan, A.; Barniakov, A.Y.; Barniakov, M.Y.; Blinov, V.E.; Druzhinin, V.P.; Golubev, V.B.; Kononov, S.A.; Koop, I.A.; Kravchenko, E.A.; Levichev, E.B.; Nikitin, S.A.; Onuchin, A.P.; Piminov, P.A.; Serednyakov, S.I.; Shatilov, D.N.; Skovpen, Y.I.; Solodov, E.A.; Cheng, C.H.; Echenard, B.; Fang, F.; Hitlin, D.J.; Porter, F.C.; Asner, D.M.; Pham, T.N.; Fleischer, R.; Giudice, G.F.; Hurth, T.; Mangano, M.; Mancinelli, G.; Meadows, B.T.; Schwartz, A.J.; Sokoloff, M.D.; Soffer, A.; Beard, C.D.; Haas, T.; Mankel, R.; Hiller, G.; Ball, P.; Pappagallo, M.; Pennington, M.R.; Gradl, W.; Playfer, S.; Abada, A.; Becirevic, D.; Descotes-Genon, S.; Pene, O.; Andreotti, D.; Andreotti, M.; Bettoni, D.; Bozzi, C.; Calabresi, R.; Cecchi, A.; Cibinetto, G.; Franchini, P.; Luppi, E.; Negrini, M.; Petrella, A.; Piemontese, L.; Prencipe, E.; Santoro, V.; Stancari, G.; Anulli, F.; Baldini-Ferroli, R.; Biagini, M.E.; Boscolo, M.; Calcaterra, A.; Drago, A.; Finocchiaro, G.; Guiducci, S.; Isidori, G.; Pacetti, S.; Patteri, P.; Peruzzi, I.M.; Piccolo, M.; Preger, M.A.; Raimondi, P.; Rama, M.; Vaccarezza, C.; Zallo, A.; Zobov, M.; De Sangro, R.; Buzzo, A.; Lo Vetere, M.; Macri, M.; Monge, M.R.; Passaggio, S.; Patrignani, C.; Robutti, E.; Tosi, S.; Matias, J.; Panduro Vazquez, W.; Borzumati, F.; Eyges, V.; Prell, S.A.; Pedlar, T.K.; Korpar, S.; Pestonik, R.; Staric, M.; Neubert, M.; Denig, A.G.; Nierste, U.; Agoh, T.; Ohmi, K.; Ohnishi, Y.; Fry, J.R.; Touramanis, C.; Wolski, A.; Golob, B.; Krizan, P.; Flaecher, H.; Bevan, A.J.; Di Lodovico, F.; George, K.A.; Barlow, R.; Lafferty, G.; Jawahery, A.; Roberts, D.A.; Simi, G.; Patel, P.M.; Robertson, S.H.; Lazzaro, A.; Palombo, F.; Kaidalov, A.; Buras, A.J.; Tarantino, C.; Buchalla, G.; Sanda, A.I.; D'Ambrosio, G.; Ricciardi, G.; Bigi, I.; Jessop, C.P.; Losecco, J.M.; Honscheid, K.; Arnaud, N.; Chehab, R.; Fedala, Y.; Polci, F.; Roudeau, P.; Sordini, V.; Soskov, V.; Stocchi, A.; Variola, A.; Vivoli, A.; Wormser, G.; Zomer, F.; Bertolin, A.; Brugnera, R.; Gagliardi, N.; Gaz, A.; Margoni, M.; Morandin, M.; Posocco, M.; Rotondo, M.; Simonetto, F.; Stroili, R.; Bonneaud, G.R.; Lombardo, V.; Calderini, G.; Ratti, L.; Speziali, V.; Biasini, M.; Covarelli, R.; Manoni, E.; Servoli, L.; Angelini, C.; Batignani, G.; Bettarini, S.; Bosi, F.; Carpinelli, M.; Cenci, R.; Cervelli, A.; Dell'Orso, M.; Forti, F.; Giannetti, P.; Giorgi, M.; Lusiani, A.; Marchiori, G.; Massa, M.; Mazur, M.A.; Morsani, F.; Neri, N.; Paoloni, E.; Raffaelli, F.; Rizzo, G.; Walsh, J.; Braun, V.; Lenz, A.; Adams, G.S.; Danko, I.Z.; Baracchini, E.; Bellini, F.; Cavoto, G.; D'Orazio, A.; Del Re, D.; Di Marco, E.; Faccini, R.; Ferrarotto, F.; Gaspero, Mario; Jackson, P.; Martinelli, G.; Mazzoni, M.A.; Morganti, Silvio; Piredda, G.; Renga, F.; Silvestrini, L.; Voena, C.; Catani, L.; Di Ciaccio, A.; Messi, R.; Santovetti, E.; Satta, A.; Ciuchini, M.; Lubicz, V.; Wilson, F.F.; Godang, R.; Chen, X.; Liu, H.; Park, W.; Purohit, M.; Trivedi, A.; White, R.M.; Wilson, J.R.; Allen, M.T.; Aston, D.; Bartoldus, R.; Brodsky, S.J.; Cai, Y.; Coleman, J.; Convery, M.R.; DeBarger, S.; Dingfelder, J.C.; Dubois-Felsmann, G.P.; Ecklund, S.; Fisher, A.S.; Haller, G.; Heifets, S.A.; Kaminski, J.; Kelsey, M.H.; Kocian, M.L.; Leith, D.W.G.S.; Li, N.; Luitz, S.; Luth, V.; MacFarlane, D.; Messner, R.; Muller, D.R.; Nosochkov, Y.; Novokhatski, A.; Pivi, M.; Ratcliff, B.N.; Roodman, A.; Schwiening, J.; Seeman, J.; Snyder, A.; Sullivan, M.; Va'Vra, J.; Wienands, U.; Wisniewski, W.; Stoeck, H.; Cheng, H.Y.; Li, H.N.; Keum, Y.Y.; Gronau, M.; Grossman, Y.; Bianchi, F.; Gamba, D.; Gambino, P.; Marchetto, F.; Menichetti, Ezio A.; Mussa, R.; Pelliccioni, M.; Dalla Betta, G.F.; Bomben, M.; Bosisio, L.; Cartaro, C.; Lanceri, L.; Vitale, L.; Azzolini, V.; Bernabeu, J.; Lopez-March, N.; Martinez-Vidal, F.; Milanes, D.A.; Oyanguren, A.; Paradisi, P.; Pich, A.; Sanchis-Lozano, M.A.; Kowalewski, Robert V.; Roney, J.M.; Back, J.J.; Gershon, T.J.; Harrison, P.F.; Latham, T.E.; Mohanty, G.B.; Petrov, A.A.; Pierini, M.; INFN

    2007-01-01

    The physics objectives of SuperB, an asymmetric electron-positron collider with a luminosity above 10^36/cm^2/s are described, together with the conceptual design of a novel low emittance design that achieves this performance with wallplug power comparable to that of the current B Factories, and an upgraded detector capable of doing the physics in the SuperB environment.

  8. Properties of Super-Poisson Processes and Super-Random Walks with Spatially Dependent Branching Rates

    Institute of Scientific and Technical Information of China (English)

    Yan Xia REN

    2008-01-01

    The global supports of super-Poisson processes and super-random walks with a branching mechanism ψ(z)=z2 and constant branching rate are known to be noncompact. It turns out that, for any spatially dependent branching rate, this property remains true. However, the asymptotic extinction property for these two kinds of superprocesses depends on the decay rate of the branching-rate function at infinity.

  9. A generalized super AKNS hierarchy associated with Lie superalgebra sl(2|1) and its super bi-Hamiltonian structure

    Science.gov (United States)

    Han, Jingwei; Yu, Jing

    2017-03-01

    Starting from a 3 × 3 matrix-valued spectral problem associated with a Lie superalgebra sl(2|1), a generalized super Ablowitz-Kaup-Newell-Segur (AKNS) hierarchy is derived. The resulting super AKNS hierarchy has a super bi-Hamiltonian structure by the supertrace identity.

  10. Super SI燃烧方式试验研究%Super SI Combustion Mode

    Institute of Scientific and Technical Information of China (English)

    沈义涛; 吕世亮; 尹琪; 杨嘉林; 高卫民

    2011-01-01

    The super spark ignition (Super SI) combustion mode, which was the ignition combustion of lean mixture at the temperature of close spontaneous combustion, was researched and its combustion characteristic and feasibility were analyzed.The results indicate that the increase of intake temperature can reduce the cyclic variation of Pmi obviously, shorten the combustion duration and extend the lean limit of SI combustion under the condition of lean mixture. Accordingly, Super SI combustion has the advantages of high thermal efficiency and controllable combustion process.%研究了Super Spark Ignition(Super SI)燃烧方式,即稀薄混合气在近自燃温度状态下点燃燃烧,分析了这种燃烧方式的可行性和燃烧特性.研究结果表明,混合气稀薄时提高发动机的进气温度可显著降低平均指示压力(pmi)的循环波动,缩短燃烧持续期,拓展点燃燃烧的稀薄极限;Super SI燃烧方式具有热效率高、燃烧过程可控的优点.

  11. The 2015 super-resolution microscopy roadmap

    Science.gov (United States)

    Hell, Stefan W.; Sahl, Steffen J.; Bates, Mark; Zhuang, Xiaowei; Heintzmann, Rainer; Booth, Martin J.; Bewersdorf, Joerg; Shtengel, Gleb; Hess, Harald; Tinnefeld, Philip; Honigmann, Alf; Jakobs, Stefan; Testa, Ilaria; Cognet, Laurent; Lounis, Brahim; Ewers, Helge; Davis, Simon J.; Eggeling, Christian; Klenerman, David; Willig, Katrin I.; Vicidomini, Giuseppe; Castello, Marco; Diaspro, Alberto; Cordes, Thorben

    2015-11-01

    Far-field optical microscopy using focused light is an important tool in a number of scientific disciplines including chemical, (bio)physical and biomedical research, particularly with respect to the study of living cells and organisms. Unfortunately, the applicability of the optical microscope is limited, since the diffraction of light imposes limitations on the spatial resolution of the image. Consequently the details of, for example, cellular protein distributions, can be visualized only to a certain extent. Fortunately, recent years have witnessed the development of ‘super-resolution’ far-field optical microscopy (nanoscopy) techniques such as stimulated emission depletion (STED), ground state depletion (GSD), reversible saturated optical (fluorescence) transitions (RESOLFT), photoactivation localization microscopy (PALM), stochastic optical reconstruction microscopy (STORM), structured illumination microscopy (SIM) or saturated structured illumination microscopy (SSIM), all in one way or another addressing the problem of the limited spatial resolution of far-field optical microscopy. While SIM achieves a two-fold improvement in spatial resolution compared to conventional optical microscopy, STED, RESOLFT, PALM/STORM, or SSIM have all gone beyond, pushing the limits of optical image resolution to the nanometer scale. Consequently, all super-resolution techniques open new avenues of biomedical research. Because the field is so young, the potential capabilities of different super-resolution microscopy approaches have yet to be fully explored, and uncertainties remain when considering the best choice of methodology. Thus, even for experts, the road to the future is sometimes shrouded in mist. The super-resolution optical microscopy roadmap of Journal of Physics D: Applied Physics addresses this need for clarity. It provides guidance to the outstanding questions through a collection of short review articles from experts in the field, giving a thorough

  12. Lightweight Ultrahigh Temperature CMC-Lined C/C Combustion Chambers, Phase II Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA and DoD are seeking high-performance, lightweight liquid rocket combustion chambers with future performance goals that cannot be achieved using state-of-the-art...

  13. Self Deployable Ultra-Lightweight Modular Unit for Habitat Structural Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Space deployable and rigidizable structures which are ultra-lightweight, and have high rigidity, space durability, and high impact resistance are desirable to...

  14. Ultra-Lightweight, High Efficiency Silicon-Carbide (SIC) Based Power Electronic Converters Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Small Business of Innovation Research Phase I proposal seeks to investigate and prove the feasibility of developing highly efficient, ultra-lightweight SiC...

  15. Ultra-Lightweight High Efficiency Nanostructured Materials and Coatings for Deep Space Mission Environments Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NanoSonic has developed a nanostructured spray self-assembly manufacturing method that has resulted in ultra-lightweight (< 0.4g/cc) textile interconnects for...

  16. Lightweight and Compace Multifunction Computer-Controlled Strength and Aerobic Training Device Project

    Data.gov (United States)

    National Aeronautics and Space Administration — TDA Research proposes to develop a computer-controlled lightweight and compact device for aerobic and resistive training (DART) to counteract muscular atrophy and...

  17. Flexible, Lightweight, Low-Cost Organic Photovoltaics with Improved Efficiency Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Both manned and unmanned off-Earth missions of the future will require very lightweight, high efficiency, flexible and durable photovoltaic (PV) arrays to generate...

  18. Ultra-Lightweight Nanocomposite Foams and Sandwich Structures for Space Structures Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Space structures that are ultra-lightweight, and have gas barrier property, space durability, radiation resistance, EMI shielding, and high impact resistance are...

  19. CIRS-lite as a lightweight atmospheric sounder for Earth trace-gas science Project

    Data.gov (United States)

    National Aeronautics and Space Administration — CIRS-lite is a lightweight  version of the CIRS 43-kg Fourier transform spectrometer (FTS) currently returning data from Saturn.  CIRS-lite is of interest...

  20. Lightweight Brick by Carbon Ash from The Mixed Plastic Waste Treatment Plant

    Directory of Open Access Journals (Sweden)

    Chen Kuo-Wei

    2016-01-01

    Full Text Available This study was designed to investigate the mixed plastic waste from the production of light carbon ash bricks performance. The mixed waste plastic pyrolysis process generated waste - Carbon ash. After extrusion, a Lightweight brick was made by carbon ash, additive and Cement mortar. In general, the set compressive strength and insulation effect of lightweight bricks with carbon ash proportion for significant impact. The set water absorption and thermal conductivity of lightweight bricks with carbon ash proportion for significant impact. The set density of lightweight brick ameliorates with M3824 additive and CM3 cement mortar for significant impact. Under conditions of technology and economic, the results of this study as reference for market-oriented marketing and commercialization of production.

  1. Ultra-Lightweight Self-Deployable SMP Nanocomposite Sandwich for Habitat Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Space deployable and rigidizable structures that are ultra-lightweight, and have gas barrier property, space durability, and high impact resistance are desirable to...

  2. A Compact, Light-weight, Reliable and Highly Efficient Heat Pump for Project

    Data.gov (United States)

    National Aeronautics and Space Administration — RTI proposes to develop an efficient, reliable, compact and lightweight heat pump for space applications. The proposed effort is expected to lead to (at the end of...

  3. Silicon Carbide Lightweight Optics With Hybrid Skins for Large Cryo Telescopes Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Optical Physics Company (OPC) proposes to manufacture new silicon carbide (SiC) foam-based optics that are composite, athermal and lightweight (FOCAL) that provide...

  4. Ultra-Lightweight Nanocomposite Foams and Sandwich Structures for Space Structures Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Space structures that are ultra-lightweight, and have gas barrier property, space durability, radiation resistance and high impact resistance are desirable to...

  5. Actively Cooled Silicon Lightweight Mirrors for Far Infrared and Submillimeter Optical Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA Space Science Enterprise has 2 themes requiring large, lightweight cryogenic mirrors: Astronomical Search for Origins and Planetary Systems (ASO) and the...

  6. Lightweight Design of an HTS Coil for the VASIMR Experiment Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this Phase II SBIR contract Tai-Yang Research Company of Tennessee proposes to design, fabricate, and test an ultra-lightweight High Temperature Superconducting...

  7. Actively Cooled Silicon Lightweight Mirrors for Far Infrared and Submillimeter Optical Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Schafer proposes to demonstrate 2 different methods for actively cooling our 5-7.5 kg/m2 areal density Silicon Lightweight Mirrors (SLMS?) technology for future NASA...

  8. Innovative, Lightweight Thoraeus RubberTM for MMOD and Space Radiation Shielding Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NanoSonic offers an innovative manufacturing process to yield ultra-lightweight radiation shielding nanocomposites by exploiting the concept of the Thoraeus filter...

  9. Lightweight Hybrid Ablator Incorporating Aerogel-Filled Open-Cell Foam Structural Insulator, Phase II Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In previous work for NASA and DoD, Ultramet developed lightweight open-cell foam insulators composed of a carbon or ceramic structural foam skeleton filled with a...

  10. Lightweight Hybrid Ablator Incorporating Aerogel-Filled Open-Cell Foam Structural Insulator Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In previous work for NASA and DoD, Ultramet developed lightweight open-cell foam insulators composed of a carbon or ceramic structural foam skeleton filled with a...

  11. Efficient Lightweight AC-AC Power Control for Solar UAV Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A highly efficient and lightweight dual bridge matrix power controller development is proposed that will provide high performance to a solar powered high altitude...

  12. Scalable, Lightweight, Low-Cost Aero/Electrodynamic Drag Deorbit Module Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed effort will develop the "Terminator Tape Deorbit Module", a lightweight, low-cost, scalable de-orbit module that will utilize both aerodynamic drag...

  13. Lightweight Ultrahigh Temperature CMC-Encased C/C Structure for Reentry and Hypersonic Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The reentry spacecraft and hypersonic cruisers of the future will require advanced lightweight thermal protection systems that can provide the dual functionality of...

  14. Next Generation , Lightweight, Durable Boot Materials to Provide Active & Passive Thermal Protection Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this NASA Phase I SBIR program is to leverage lightweight, durable materials developed by NanoSonic for use within extra vehicular activity (EVA)...

  15. Silicon Carbide Lightweight Optics With Hybrid Skins for Large Cryo Telescopes Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Optical Physics Company (OPC) has developed new silicon carbide (SiC) foam-based optics with hybrid skins that are composite, athermal and lightweight (FOCAL) that...

  16. Mitigation of Flanking Noise Transmission in Periodic Structures of Lightweight Elements

    DEFF Research Database (Denmark)

    Domadiya, Parthkumar Gandalal

    Lightweight structures becoming increasingly popular within the building industry and hence they requires immediate attention to address their vibro-acoustic behaviour. Flanking noise transmission is one of the main concerns while using lightweight panels in buildings, since sound can travel...... characteristics in periodic structures, the structure must be simplified; hence, one dimensional structures such as bars and beams are considered for further investigation. A periodic bar model comprised of systemically placed Plexiglas and steel elements is generated using two methods: an FE method and a Floquet...... transmission in periodic structures of lightweight elements by employing various numerical, analytical and experimental methods. At first, three dimensional finite-element (FE) models of a Z-shaped lightweight panel structure based on various frame designs, inclusion of air and structural coupling between...

  17. Ultra-Lightweight, High Efficiency Silicon-Carbide (SIC) Based Power Electronic Converters Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In Phase I of this project, APEI, Inc. proved the feasibility of creating ultra-lightweight power converters (utilizing now emerging silicon carbide [SiC] power...

  18. Flexible, Lightweight, Low-Cost Organic Photovoltaics with Improved Efficiency Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Both manned and unmanned off-Earth missions of the future will require very lightweight, inexpensive, high efficiency, flexible and single-use photovoltaic (PV)...

  19. Influence of Mineral Admixtures on the Permeability of Lightweight Aggregate Concrete

    Institute of Scientific and Technical Information of China (English)

    WANG Fazhou; HU Shuguang; DING Qingjun; PENG yanzhou

    2005-01-01

    The permeability of lightweight aggregate concrete was studied. Some efforts were taken to increase the resistance of lightweight aggregate concrete (LC) to water penetration by using the mineral admixtures of fly ash, granulated blast furnace slag or silica fume. Accelerated chloride penetrability test and liquid atmosphere press method were used to study the anti-permeability of lightweight aggregate concrete. The experimental results show that fly ash, granulated blast furnace slag and silica fume can decrease the permeability of lightweight aggregate concrete, but the effect of granulated blast furnace slag is poor. According to the SEM and pore structure analyzing results,an interface self-reinforcing effect model was presented and the reinforced mechanism of mineral mixture on LC was discussed according to the model described by authors.

  20. Lightweight Metal Rubber Wire and Cable for Space Power Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this NASA STTR program is to produce ultra-lightweight electrical wire and cable harnesses to reduce the liftoff weight of future space flight...