Disposal of olive oil mill wastes in evaporation ponds: effects on soil properties.

Science.gov (United States)

Kavvadias, V; Doula, M K; Komnitsas, K; Liakopoulou, N

2010-10-15

The most common practice followed in the Med countries for the management of olive oil mill wastes (OMW) involves disposal in evaporation ponds or direct disposal on soil. So far there is lack of reliable information regarding the long-term effects of OMW application on soils. This study assesses the effects of OMW disposal in evaporation ponds on underlying soil properties in the wider disposal site as well as the impacts of untreated OMW application on agricultural soils. In case of active disposal sites, the carbonate content in most soils was decreased, whereas soil EC, as well as Cl(-), SO(4)(2-), PO(4)(3-), NH(4)(+) and particularly K(+) concentrations were substantially increased. Soil pH was only marginally affected. Phenol, total N, available P and PO(4)(3-) concentrations were considerably higher in the upper soil layers in areas adjacent to the ponds. Available B as well as DTPA extractable Cu, Mn, Zn and Fe increased substantially. Most surface soil parameters exhibited increased values at the inactive site 6 years after mill closure and cease of OMW disposal activities but differences were diminished in deeper layers. It is therefore concluded that long-term uncontrolled disposal of raw OMW on soils may affect soil properties and subsequently enhance the risk for groundwater contamination. 2010 Elsevier B.V. All rights reserved.

Sugar composition and FT-IR analysis of exopolysaccharides produced by microbial isolates from paper mill slime deposits

NARCIS (Netherlands)

Verhoef, R.P.; Schols, H.A.; Blanco, A.; Siika-aho, M.; Ratto, M.; Buchert, J.; Lenon, G.; Voragen, A.G.J.

2005-01-01

Thirty exopolysaccharides (EPS) produced by bacteria isolated from biofilms or slimelayers from different paper and board mills in Finland, France and Spain were subjected to size exclusion chromatography and sugar compositional analysis. High performance size exclusion chromatography (HPSEC)

Techno-economic assessment of integrating methanol or Fischer-Tropsch synthesis in a South African sugar mill.

Science.gov (United States)

Petersen, Abdul M; Farzad, Somayeh; Görgens, Johann F

2015-05-01

This study considered an average-sized sugar mill in South Africa that crushes 300 wet tonnes per hour of cane, as a host for integrating methanol and Fischer-Tropsch synthesis, through gasification of a combined flow of sugarcane trash and bagasse. Initially, it was shown that the conversion of biomass to syngas is preferably done by catalytic allothermal gasification instead of catalytic autothermal gasification. Thereafter, conventional and advanced synthesis routes for both Methanol and Fischer-Tropsch products were simulated with Aspen Plus® software and compared by technical and economic feasibility. Advanced FT synthesis satisfied the overall energy demands, but was not economically viable for a private investment. Advanced methanol synthesis is also not viable for private investment since the internal rate of return was 21.1%, because it could not provide the steam that the sugar mill required. The conventional synthesis routes had less viability than the corresponding advanced synthesis routes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Economic and environmental assessment of cellulosic ethanol production scenarios annexed to a typical sugar mill.

Science.gov (United States)

Ali Mandegari, Mohsen; Farzad, Somayeh; Görgens, Johann F

2017-01-01

In this work different biorefinery scenarios were investigated, concerning the co-production of bioethanol and electricity from available lignocellulose at a typical sugar mill, as possible extensions to the current combustion of bagasse for steam and electricity production and burning trash on-filed. In scenario 1, the whole bagasse and brown leaves is utilized in a biorefinery and coal is burnt in the existing inefficient sugar mill boiler. Scenario 2 & 3 are assumed with a new centralized CHP unit without/with coal co-combustion, respectively. Also, through scenarios 4 & 5, the effect of water insoluble loading were studied. All scenarios provided energy for the sugarmill and the ethanol plant, with the export of surplus electricity. Economic analysis determined that scenario 1 was the most viable scenario due to less capital cost and economies-of scale. Based on Life Cycle Assessment (LCA) results, scenario 2 outperformed the other scenarios, while three scenarios showed lower contribution to environmental burdens than the current situation. Copyright © 2016 Elsevier Ltd. All rights reserved.

South African Sugar Technologists' Association. Proceedings of the fifty-ninth annual congress held at Durban and Mount Edgecombe, 17 to 21 June 1985

International Nuclear Information System (INIS)

1985-01-01

This publication presents the proceedings of the fifty-ninth annual congress of the South African Sugar Technologists' Association, held in Durban and Mount Edgecombe, from 17 to 21 June 1985. Almost every facet of the sugar industry is covered including topics such as milling, irrigation, growth, crystal elongation and crystal size distribution, pans, stirrers and boilers used in the industry, evaporation, sucrose losses, radiometric and other gauges, the use of x-ray techniques and chemical methods of analysis, diseases, cooling waters, refining, maintenance, efficiency, operation, production and performance of a sugar station

The cogeneration potential of the sugar industry in Vietnam

International Nuclear Information System (INIS)

Bhattacharyya, S.C.; Thang, D.N.Q.

2004-01-01

Vietnam produces about 15 million tons of sugarcane per year and about five mt of bagasse. There is the potential for cogeneration using bagasse, which can also help overcome power shortages in the country. This paper analyses the potential for cogeneration from the sugar industry in Vietnam under three different scenarios and finds that between 100 and 300 megawatts of power-generating capacity could be supported by the bagasse generated from sugar mills, depending on the technology considered for sugar mills and cogeneration and the possibility of renovation of the existing mills. The paper also assesses the expense of cogeneration and finds it to be a cost-effective option for all types of sugar mill. It is found that the cost savings from cogeneration would more than offset the cost of introducing cogeneration in sugar mills with inefficient cane processing technologies. Sugar mills with modern technologies would have a significant amount of excess power and most of these plants would break-even if they sold excess power at around 4.5 cents per kilowatt hour. The break-even cost and the average production cost are sensitive to the investment cost assumptions. The paper thus suggests that cogeneration from the sugar industry is an attractive option for investors in existing mills or new sugar mills alike. (Author)

Impact of sugar industry fly ash emissions on environment

International Nuclear Information System (INIS)

Memom, A.R.; Ansari, A.K.

2001-01-01

This work was conducted in 1992 to find out the effects and causes of environmental problems due to sugar mills of Sindh. Most of the complaints were received from Nawabshah, Tando Mohammed Khan residential areas where following mills are located, emitting large amounts of fly ash from their chimneys into the atmosphere: (i) Habib Sugar Mills, Nawabshah, (II) Fauji Sugar Mills, Tando Mohammed Khan. Environmental survey of above localities was carried out which reveals that eye-allergy and asthma are the major health effects of fly ash besides the aesthetic problems. Sieve analysis of two fly ash samples viz Fauji Sugar Mills (Old Plant) and Sanghar Sugar Mills (New Plant) showed that the particle size of over 50% of fly ash was above 300 mu m. These large size black particles were unburned carbon particles, which on burning in air gave a weight loss of over 87% at 1000 centi grade. The fly ash analytical results showed that combustion of bagasse in sugar mills was not complete at all and this was not only polluting the atmosphere but also causing energy losses. (author)

One step conversion of wheat straw to sugars by simultaneous ball milling, mild acid, and fungus Penicillium simplicissimum treatment.

Science.gov (United States)

Yuan, Li; Chen, Zhenhua; Zhu, Yonghua; Liu, Xuanming; Liao, Hongdong; Chen, Ding

2012-05-01

Wheat straw is one of the major lignocellulosic plant residues in many countries including China. An attractive alternative is the utilization of wheat straw for bioethanol production. This article mainly studies a simple one-step wet milling with Penicillium simplicissimum and weak acid to hydrolysis of wheat straw. The optimal condition for hydrolysis was ball milling 48 h in citrate solvent (pH = 4) with P. simplicissimum H5 at the speed of 500 rpm and the yield of sugar increased with increased milling time. Corresponding structure transformations before and after milling analyzed by X-ray diffraction, transmission Fourier transform infrared spectroscopy, and environmental scanning electron microscopy clearly indicated that this combined treatment could be attributed to the crystalline and chemical structure changes of cellulose in wheat straw during ball milling. This combined treatment of ball milling, mild acid, and fungus hydrolysis enabled the conversion of the wheat straw. Compared with traditional method of ball milling, this work showed a more simple, novel, and environmentally friendly way in mechanochemical treatment of wheat straw.

Culture of the microalga chlorella vulgaris on different proportions of sugar mill effluents

International Nuclear Information System (INIS)

Khan, A.N.M.A.I.; Islam, M.R.; Habib, M.A.B.; Hossain, M.S.; Miah, M.I.

2006-01-01

Chlarella vulgaris was cultured in four different dilutions of sugar mill effluent media (SMEM). Bold's basal medium (BBM) was used as the control under laboratory conditions. Maximum cell growth and chlorophyll-a content were obtained on 10th day of the culture in 50% diluted SMEM, followed by those grown in BBM, and 75, 25 and 100% SMEM at stationary phase. The specific growth rate (mu g/day) of cells and chlorophyll-a of C. vulgaris grown in 50% SMEM varied significantly (p < 0.0 I) from those of C. vulgaris cultured in BBM, followed by other SMEM concentrations. Total biomass of C. vulgaris. cultured in 50% SMEM, was found to be significantly higher (p < 0.0 I) than that of C. vulgaris cultured in BBM, and 25, 75 and 100% SMEM concentrations. Similar trend was also observed in the case of optical density. Cell number and chlorophyll-a of C. vulgaris were highly (p < 0.01) and directly correlated with chlorophyll-a (r2 = 0.991) of C. vulgaris and optical density (r2 = 0.989) for the culture media containing C. vulgaris, respectively. Crude proteins and crude lipids of C. vulgaris. grown in 50% SMEM, were significantly (p < 0.01) higher than those of C. vulgaris cultured in other SMEM concentrations. Due to good growth performance exhibited in the 50% SMEM dilution, the sugar mill effluent may be used for efficient cultivation of C. vulgaris and possibly other micro algae. (author)

Sugar, acid and furfural quantification in a sulphite pulp mill: Feedstock, product and hydrolysate analysis by HPLC/RID.

Science.gov (United States)

Llano, Tamara; Quijorna, Natalia; Andrés, Ana; Coz, Alberto

2017-09-01

Waste from pulp and paper mills consist of sugar-rich fractions comprising hemicellulose derivatives and cellulose by-products. A complete characterisation of the waste streams is necessary to study the possibilities of an existing mill. In this work, four chromatographic methods have been developed to obtain the most suitable chromatographic method conditions for measuring woody feedstocks, lignocellulosic hydrolysates and cellulose pulp in sulphite pulping processes. The analysis of major and minor monosaccharides, aliphatic carboxylic acids and furfurals has been optimised. An important drawback of the spent liquors generated after sulphite pulping is their acidic nature, high viscosity and adhesive properties that interfere in the column lifetime. This work recommends both a CHO-782Pb column for the sugar analysis and an SH-1011 resin-based cross-linked gel column to separate low-molecular-weight chain acids, alcohols and furfurals. Such columns resulted in a good separation with long lifetime, wide pH operating range and low fouling issues.

Differences between easy- and difficult-to-mill chickpea (Cicer arietinum L.) genotypes. Part III: free sugar and non-starch polysaccharide composition.

Science.gov (United States)

Wood, Jennifer A; Knights, Edmund J; Campbell, Grant M; Choct, Mingan

2014-05-01

Parts I and II of this series of papers identified several associations between the ease of milling and the chemical compositions of different chickpea seed fractions. Non-starch polysaccharides were implicated; hence, this study examines the free sugars and sugar residues. Difficult milling is associated with: (1) lower glucose and xylose residues (less cellulose and xyloglucans) and more arabinose, rhamnose and uronic acid in the seed coat, suggesting a more flexible seed coat that resists cracking and decortication; (2) a higher content of soluble and insoluble non-starch polysaccharide fractions in the cotyledon periphery, supporting a pectic polysaccharide mechanism comprising arabinogalacturonan, homogalacturonan, rhamnogalalcturonan, and glucuronan backbone structures; (3) higher glucose and mannose residues in the cotyledon periphery, supporting a lectin-mediated mechanism of adhesion; and (4) higher arabinose and glucose residues in the cotyledon periphery, supporting a mechanism involving arabinogalactan-proteins. This series has shown that the chemical composition of chickpea does vary in ways that are consistent with physical explanations of how seed structure and properties relate to milling behaviour. Seed coat strength and flexibility, pectic polysaccharide binding, lectins and arabinogalactan-proteins have been implicated. Increased understanding in these mechanisms will allow breeding programmes to optimise milling performance in new cultivars. © 2013 Society of Chemical Industry.

Sugar cane/sweet sorghum as an ethanol feedstock in Louisiana and Piedmont

International Nuclear Information System (INIS)

Marsh, L.S.; Cundiff, J.S.

1991-01-01

Cost to provide readily fermentable feedstock for a year round sweet sorghum-to-ethanol production facility, up to the point at which fermentation begins, was determined. It was assumed that sweet sorghum is produced on marginal crop lands in the Southeastern Piedmont, and is purchased, standing in the field by a central ethanol production facility. Feedstock cost varied from $1.96 to $2.98/gal of ethanol potential depending on harvest system and use of by-products. Major contributors to feedstock cost were field production, harvest/field processing, and cost to evaporate juice to a storable syrup. Cost to transport feedstock to a central production facility, and cost of storage were relatively minor components of total cost, contributing only $0.05 and $0.06/gal ethanol potential, respectively. For a point of comparison, cost of producing ethanol feedstock from sugar cane, based on current processing practices in Louisiana sugar mills, was determined to be $2.50/gal ethanol potential. This cost is higher than determined for most options in the Piedmont for two reasons: (1) sugar cane demands a higher price in Louisiana than was assumed for sweet sorghum in the Piedmont, and (2) little market exists in Louisiana for by-products of sugar milling, consequently, no by-product credit was assigned. Current market value of ethanol must approximately double before a sweet sorghum-to-ethanol industry in the Piedmont could be economically viable, as no opportunity was identified for a significant reduction in feedstock cost

Assesing the effect of an olive mill wastewater evaporation pond in Sousse, Tunisia

Science.gov (United States)

S'habou, Rakia; Zairi, Moncef; Kallel, Amjed; Aydi, Abdelwaheb; Ben Dhia, Hamed

2009-08-01

Olive oil is a typical and valuable agro-industrial product in Mediterranean countries. In Tunisia, olive mill wastewaters (OMW) reach an amount of about 1,000,000 t year-1 and constitute a serious organic pollution risk because of the high chemical oxygen demand values and the presence of phytotoxic and antibacterial polyphenols. OMW have been generally stored in pond sites to be eliminated by natural evaporation or valorised by spreading on cultivated soils or by composting. Many researches on the interactions of OMW with soils at laboratory scale (columns) have been reported, but less attention have been paid to the effect of OMW on soils at field scale. The aim of this work is to investigate an area used for >15 years as an uncontrolled OMW pond site. The transformations of soil properties and groundwater occurring during OMW storage were characterised by the pH, phenolic contents, electrical conductivity (EC), moisture content and organic contents. The soil samples were taken from two borings and compared to those of a control one located near the pond site. Groundwater samples were taken on the accessible and nearest water wells to the evaporation ponds. The permeable silty and sandy layers in the site support the infiltration of OMW near the evaporation ponds. This infiltration has reached a depth of 6 m at a distance of almost 50 m laterally. The results show that the OMW infiltration in the subsoil has affected the pH, EC, organic content, phenolic compounds and the moisture.

Effects of evaporation pressure and antifoam concentration and the use of a flocculant and adjuvant on the quality of sugar honey and panela

Directory of Open Access Journals (Sweden)

Luz Esperanza Prada Forero

2014-07-01

Full Text Available The implementation of multi-effect evaporators on panela (unrefined whole cane sugar production process requires, besides the technological adjustment, to maintain product characteristics; this condition revealed the lack of knowledge of the effect of evaporation pressure on the quality of panela. In order to fill part of this gap, this study sought to determine the effect of both the concentration of antifoam and the use of a flocculant (Heliocarpus popayanensis Kunth and an adjuvant (lime on the quality of sugar honey and panela, when evaporation is performed at different atmospheric pressures. In order to achieve this, the present study worked on two completely randomized experimental designs with four replications, a density of evaporation heat flow of 27.78 kW/m2 and juice from the CC85-46 variety. In the first design, two variables were studied: evaporation pressure and use of flocculant and adjuvant with a 4x2x2 factorial arrangement without antifoam. In the second design, variables evaporation pressure and quantity of antifoam with a 4x3 factorial arrangement without flocculant nor adjuvant were studied. The results show that the quality of the product deteriorates in pressurized systems (glucoside coefficient increases up to 200%, is not affected by the use of 50 μL of antifoam per liter of clarified juice and improved by the use of flocculant (turbidity is reduced by 55%. Solidification and hardness improve with the addition of the adjuvant, but this increased 48% color and 24% turbidity.

A co-production of sugars, lignosulfonates, cellulose, and cellulose nanocrystals from ball-milled woods.

Science.gov (United States)

Du, Lanxing; Wang, Jinwu; Zhang, Yang; Qi, Chusheng; Wolcott, Michael P; Yu, Zhiming

2017-08-01

This study demonstrated the technical potential for the large-scale co-production of sugars, lignosulfonates, cellulose, and cellulose nanocrystals. Ball-milled woods with two particle sizes were prepared by ball milling for 80min or 120min (BMW 80 , BMW 120 ) and then enzymatically hydrolyzed. 78.3% cellulose conversion of BMW 120 was achieved, which was three times as high as the conversion of BMW 80 . The hydrolyzed residues (HRs) were neutrally sulfonated cooking. 57.72g/L and 88.16g/L lignosulfonate concentration, respectively, were harvested from HR 80 and HR 120 , and 42.6±0.5% lignin were removed. The subsequent solid residuals were purified to produce cellulose and then this material was acid-hydrolyzed to produce cellulose nanocrystals. The BMW 120 maintained smaller particle size and aspect ratio during each step of during the multiple processes, while the average aspect ratio of its cellulose nanocrystals was larger. The crystallinity of both materials increased with each step of wet processing, reaching to 74% for the cellulose. Copyright © 2017 Elsevier Ltd. All rights reserved.

Olive mill wastewater sludge from evaporation ponds: evolution of physico-chemical parameters during storage and composting process.

Science.gov (United States)

Abid, N; Aloui, F; Dhouib, A; Sayadi, S

2006-02-01

The evolution of analytical parameters of olive mill waste water sludge stored in evaporation ponds was investigated after one year and two years of storage. It was observed that some of the phenolic monomer compounds resisted removal and the fraction of water soluble phenols was only slightly polymerised. Co-composting of the sludge was carried out with yard trimming as bulking agent ratio and poultry manure to balance the C/N. Three turned piles with three proportions of 35%, 65% and 80% of olive mill waste water sludge were prepared. Co-composting of the sludge was possible in all the cases. Best results were obtained, however, at a proportion of 35% which permitted a shorter composting time, a higher degree of nitrification and a higher rate of total phenols decreasing. A high polymerisation of the fraction of water soluble phenols was observed at the end of composting in all the piles.

Techno-economic and ex-ante environmental assessment of C6 sugars production from spruce and corn. Comparison of organosolv and wet milling technologies

NARCIS (Netherlands)

Moncada, Jonathan; Vural Gursel, Iris; Huijgen, Wouter J J; Dijkstra, Jan Wilco; Ramírez, Andrea

2018-01-01

This study assesses the techno-economic and environmental performance of C6 sugars production from softwood (spruce) and corn. Two technologies were considered in the assessment: organosolv of spruce woodchips (2nd generation) and corn wet milling (1st generation). Process models were developed to

Supply optimization for the production of raw sugar

DEFF Research Database (Denmark)

Grunow, Martin; Günther, H.O.; Westinner, R.

2007-01-01

Based on a case study from Venezuela, the production of raw sugar is investigated. Ideally, sugar mills operate at a constant production rate. However, safety stocks of the raw material cannot be maintained as sugar cane quality deteriorates very rapidly. Sugar cane is therefore continuously...

Case studies on sugar production from underutilized woody biomass using sulfite chemistry

Science.gov (United States)

J.Y. Zhu; M. Subhosh Chandra; Roland Gleisner; William Gilles; Johnway Gao; Gevan Marrs; Dwight Anderson; John Sessions

2015-01-01

We examined two case studies to demonstrate the advantages of sulfite chemistry for pretreating underutilized woody biomass to produce sugars through enzymatic saccharification. In the first case study, we evaluated knot rejects from a magnesium-basedsulfite mill for direct enzymatic sugar production.We found that the sulfite mill rejects are an excellent feedstock for...

Economic feasibility study of an electric generation project from bagasse gasification in a cuban sugar mill

International Nuclear Information System (INIS)

Torres Fernández, Alfredo; Almazán del Olmo, Oscar; Hernández, Bárbara

2015-01-01

Some solid fuels which are very pollutant and with low value could be transformed into a clean gas that could be used in many industrial applications for its physical properties and for being easy transported. Then, electricity generation is one of the most important applications. In this case, electricity could be generated, cleanly and efficiently, through the use of synthesis gas that replaces the natural gas in a combined cycle (Biomass Integrated Gasification Combined Cycle (BIGCC)).In this paper, we carry out an economic feasibility study of the project about the implementation of Biomass Integrated Gasification Combined Cycle (BIGCC) in a 10000 tc/d sugar mill from bagasse gasification in order to demonstrate, from the economic point of view, the possibility of investment in this kind of technology considering the current conditions of Cuban sugar industry.Later, a sensitivity analysis is presented to show first, the break-even point associated to the project and second, the variations of financial indicators due to changes on the total amount of investments, which is a very helpful element for making right decisions in the project investment process. (author)

Time-dependent evolution of olive mill wastewater sludge organic and inorganic components and resident microbiota in multi-pond evaporation system.

Science.gov (United States)

Jarboui, Raja; Chtourou, Mohamed; Azri, Chafai; Gharsallah, Néji; Ammar, Emna

2010-08-01

The physico-chemical and microbiological characterizations of olive mill wastewater sludge (OMWS) were investigated in five OMW evaporation ponds of the open-pond system in Sfax (Tunisia), during the olive oil production period in 2004. Time-dependent changes in both physico-chemical parameters and the microbiota were investigated. Mathematical models and principal component analysis (PCA) were used to establish the correlations between the studied parameters. During the effluent time-dependent changes in the ponds, the result of OMWS analysis showed an increase of sludge index (SI), ash content, total solids (TS), volatile solids (VS), ethyl acetate extractive (EAE) and total phosphorus (Total P), as well as microbial flora especially the yeasts and moulds. The SI, TS, VS and Total P changes with time fit a simple linear equation, while EAE, phenols and NH(4)(+) fit a second-degree polynomial model. The PCA analysis exhibited three correlated groups. The first group included temperature, ash content, evaporation, SI, TS, VS, Total P, EAE, yeasts and moulds. The second group was made by bacteria and moisture; and the third group by NH(4)(+), oil and phenol. Such modelling might be of help in the prediction of OMW changes in natural evaporation ponds. (c) 2010 Elsevier Ltd. All rights reserved.

Characterization of sugar beet pulp derived oligosaccharides

NARCIS (Netherlands)

Leijdekkers, M.

2015-01-01

Abstract

This thesis aimed at characterizing complex mixtures of sugar beet pulp derived oligosaccharides, in order to be able to monitor and optimize the enzymatic saccharification of sugar beet pulp.

Hydrophilic interaction chromatography with on-line evaporative

Mathematical modelling and simulation of the operation in sugar and alcohol industry: 2 - evaporation; Modelagem matematica e simulacao das operacoes da industria de acucar e alcool: 2 - evaporacao

Energy Technology Data Exchange (ETDEWEB)

Chiappetta, A; Giudici, R; Nascimento, C A.O. do [Sao Paulo Univ., SP (Brazil). Escola Politecnica

1987-12-31

A mathematical model is presented for steady-state simulation of multiple-effects evaporators systems used for concentration of sugar solution. The model basis are the fundamental energy and mass balances equations, as well as empirical correlations for the problem being handled. The evaporation system simulation is performed with an executive program which allows different process configurations. For one typical case, some process parameters (volumetric rate and concentration of feed;exhaust steam temperature) influences on syrup concentration and solution temperature were studied. (author) 8 figs., 2 refs.

The potential for energy savings when reducing the water consumption in a kraft pulp mill

Energy Technology Data Exchange (ETDEWEB)

Wising, Ulrika; Berntsson, Thore [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Chemical Engineering and Environmental Science; Stuart, Paul [Ecole Polytechnique, Montreal (Canada). Dept. of Chemical Engineering

2004-05-01

In this paper an existing pulp and paper mill has been studied in a systematic way regarding the reduction of water consumption, and the resulting increased potential for energy integration. It has been found that when the mill's hot water consumption is decreased, the live steam demand for the mill also decreases. Also when decreasing the hot water consumption, the quantity and temperature of available excess heat increases. This excess heat can be used for evaporation, thereby reducing the live steam demand further by up to 1.5 GJ/t. A pinch analysis was performed at an existing mill and it was found that if pinch violations are removed, the hot water consumption is not an important factor any more. Removing all the pinch violations and using the remaining excess heat for evaporation yields a significantly larger energy savings for the mill (4.0 GJ/t). From an economic optimum perspective it is probably most profitable to do a combination of reducing water consumption, removing pinch violations, and use the remaining excess heat for evaporation.

Integration of Succinic Acid Production in a Dry Mill Ethanol Facility

Energy Technology Data Exchange (ETDEWEB)

None

2006-08-01

This project seeks to address both issues for a dry mill ethanol biorefinery by lowering the cost of sugars with the development of an advanced pretreatment process, improving the economics of succinic acid (SA), and developing a model of an ethanol dry mill to evaluate the impact of adding different products and processes to a dry mill.

Modelación matemática de la flotación de la maza superior de los molinos de caña de azúcar // Mathematical model for instant flotation of top shaft in sugar cane mills

Directory of Open Access Journals (Sweden)

Mario Javier Cabello‐Ulloa

2012-01-01

Full Text Available En el presente trabajo se desarrolla un modelo matemático de la flotación de la maza superior de losmolinos de caña de azúcar durante su funcionamiento, determinado a partir de medicionesexperimentales de dicha magnitud en el tiempo. Se realiza un ajuste adecuado a los valores medidosexperimentalmente y se obtiene una función analítica que permitirá considerar los efectos de la flotaciónen el estudio del funcionamiento y en los métodos de cálculo de los molinos y sus elementos. Se aplica aun molino en el Complejo Agroindustrial 14 de Julio en Cienfuegos. Se modelan cien segundos defuncionamiento obteniéndose una función que expresa la flotación la que al ser derivada permite obtenerla velocidad y aceleración con que varía la flotación instantánea. Los coeficientes y sus bondades sondados matricialmente para todos los ajustes efectuados al construir la función que define la flotacióninstantánea obtenida en este caso.Palabras claves: molino de caña de azúcar, flotación instantánea, modelación, cinemática del molino._________________________________________________________________AbstractA mathematical model for the instant flotation of the top shaft of sugar cane mill is developed andanalytical function for introduce in the study of other sugar cane mills parts is obtained. The model isapplied to July 14th sugar factory in Cienfuegos. One hundred seconds of work is modeled and a functionsfor floating, velocity and acceleration of floating are obtained. The coefficients and their goodness aregiven in matrix for all the fits made for to build the function that defines the instant flotation obtained in thiscase.Key words: sugar cane mill, instant flotation, modeling, mill kinematics.

Hydrogen photo-evolution by Rhodopseudomonas palustris 6A using pre-treated olive mill wastewater and a synthetic medium containing sugars

International Nuclear Information System (INIS)

Pintucci, Cristina; Padovani, Giulia; Giovannelli, Alessio; Traversi, Maria Laura; Ena, Alba; Pushparaj, Benjamin; Carlozzi, Pietro

2015-01-01

Highlights: • Adsorbent matrices to convert fresh olive mill wastewater (OMW F ) in feedstock. • Dry-Azolla and granular active carbon for adsorbing polyphenols from OMW F . • Photofermentative processes for biohydrogen production. • Culture mixing by means of an impeller or a magnetic stir bar. • A 30% of dephenolised OMW containing medium suits the photofermentative process. - Abstract: Increasing costs of petroleum, associated with the escalating problems of global climate change, require always greater efforts in order to produce an energy carrier as bioH 2 . In this study, bioH 2 production using photofermentative process was investigated. Two culture broths were used: (a) a synthetic medium rich in sugars (glucose and fructose) and (b) a pre-treated fresh olive-mill wastewater (OMW F ) diluted with water (30%, v:v). The pre-treatment was carried out using two different vegetable matrices (dry-Azolla and granular active carbon) to decrease both the content of polyphenols and the dark colour of wastewater. Rhodopseudomonas palustris 6A isolated from soil spread with OMW was utilized for batch growth experiments, carried out indoors under continuous light (200 μE/m 2 /s). When synthetic medium was used, the culture mixing was performed using either (i) a magnetic stir bar, and (ii) an impeller equipped with five turbines. The latter system made it possible to increase the bioH 2 photo-evolution by 1.4 times. The specific hydrogen photo-evolution rate was 13.5 mL/g(dw)/h in the broth containing diluted OMW F and 11.8 mL/g(dw)/h in the synthetic medium containing sugars (glucose and fructose)

Evaluation of electrolytic alkaline cleaners by evaporative-rate analysis

International Nuclear Information System (INIS)

Hamilton, C.B.

1975-01-01

A method has been developed by which electrolytic alkaline cleaners used in large volumes in steel mills can be evaluated for their ability to clean rolling oil from steel strip without the necessity of large-scale mill trials. The method is evaporative-rate analysis, which can be used to determine the relative amount of residual oil on steel strip after cleaning. The procedure consists in placing a droplet of a solution of a volatile, radioactive, carbon-14 tagged organic compound dissolved in a more volatile solvent, on the surface of the metal, where it forms a ternary solution with any oil on the surface. The amount of oil in this ternary solution affects the rate of evaporation of the tagged compound. The rate of evaporation, monitored by a Geiger-Mueller detector, is a measure of the cleanliness of the surface. A number of commercial alkaline cleaners, both solids and liquids, were evaluated over a range of concentrations. Results indicated that the effectiveness of commercial alkaline cleaners varies greatly, and is a function of the cleaner concentration, cleaner composition, and polarity of cleaning. The presence of antifoaming agents also affects cleaning ability. The results of this study indicate that evaporative-rate analysis is a rapid and effective method for evaluating cleaners

Novel micronized woody biomass process for production of cost-effective clean fermentable sugars.

Science.gov (United States)

Fu, Yu; Gu, Bon-Jae; Wang, Jinwu; Gao, Johnway; Ganjyal, Girish M; Wolcott, Michael P

2018-03-29

Thermo-chemical pretreatments of biomass typically result in environmental impacts from water use and emission. The degradation byproducts in the resulting sugars can be inhibitory to the activities of enzymes and yeasts. The results of this study showed that combining existing commercial comminution technology can reduce total energy consumption with improved saccharification yield while eliminating chemical use. Impact mill was found to be the most efficient milling for size reduction of forest residual chips from ca. 2 mm to a specific value below 100 µm. The further micronization effectively disrupted the recalcitrance of the woody biomass and produced the highly saccharifiable substrates for downstream processing. In addition, extrusion can be integrated into a clean cellulosic sugar process for further fibrillation in place of the conventional mixing processing. The highest energy efficiency was observed on the impact-milled samples with 0.515 kg sugars kWh -1 . Copyright © 2018 Elsevier Ltd. All rights reserved.

Pyrolysis and thermal oxidation kinetics of sugar mill press mud

International Nuclear Information System (INIS)

Gangavati, P.B.; Safi, M.J.; Singh, A.; Prasad, B.; Mishra, I.M.

2005-01-01

Press mud, a solid waste obtained from the sugar mills, has the potential of energy generation through pyrolysis and gasification. The paper reports its proximate and ultimate analyses, deformation and fusion ash temperatures, lower and higher heating values, physico-chemical and thermal degradation in nitrogen and air atmospheres. The thermal degradation was conducted in a thermogravimetric analyzer from room temperature to 900 deg C at heating rates of 20 and 40 K min -1 . The thermogravimetric, derivative thermogravimetric and differential thermal analyses were carried out to determine the rate of volatiles evolution, the effect of heating rates on the thermal degradation characteristics and to determine the global mass loss kinetics of thermal degradation. The thermal degradation was found to occur in several distinct phases: each phase giving volatile evolution in an independent parallel lump. Each decomposition phase was modeled by a single irreversible reaction with respect to the solid mass. Global mass loss kinetics was also determined for the entire decomposition process, as if occurring in one single step. The integral and differential techniques were used for the determination of kinetic parameters. Using the method of Agrawal and Sivasubramanian [R.K. Agrawal, M.S. Sivasubramanian, AIChE J. 33 (1987) 7] for the total degradation zone, the orders of reaction were found in the range of 1.00-2.50 in both the atmospheres (i.e. nitrogen and air) and the activation energy in the range of 27.84-33.44 and 57.41-88.92 kJ mol -1 in nitrogen and air, respectively. The pre-exponential factor was found in the range of 32.1-95.1 and 5.10 x 10 4 to 5.46 x 10 9 min -1 in nitrogen and air atmospheres, respectively

Olive mill wastewater disposal in evaporation ponds in Sfax (Tunisia): moisture content effect on microbiological and physical chemical parameters.

Science.gov (United States)

Jarboui, Raja; Hadrich, Bilel; Gharsallah, Néji; Ammar, Emna

2009-11-01

The study of the isotherms desorption of olive mill wastewater (OMW) was investigated to describe its water activity under different saturated environments. The microbial biodegradation of OMW during its storage in 5 evaporation ponds located in Agareb (Sfax-Tunisia) was carried out during the oil-harvesting year held 105 days in 2004. Gravimetric static method using saturated salt solutions was used and OMW as placed at 30 degrees C and under different water activities ranging from 0.11 to 0.90. Eight models were taken from the literature to describe experimental desorption isotherms. During storage, the evolution of physico-chemical parameters including pH, temperature, evaporation, humidity, total phosphorus, chemical oxygen demand (COD), biological oxygen demand (BOD) and phenols and three microbiological flora (aerobic mesophilic bacteria, yeasts and moulds) were considered. At 30 degrees C, when relative humidity increased in the experimented ponds of 69, 84 and 90%, the evaporation speed decreased from 1.24 x 10(-5) to 5 x 10(-6) cm(3) s(-1), from 6 x 10(-5) to 7 x 10(-6) cm(3) s(-1) and from 5 x 10(-6) to 1.1 x 10(-7) cm(3) s(-1) respectively. The desorption isotherm exhibited a sigmoidal curve corresponding to type II, typical of many organic material. The GAB and Peleg models gave the best fit for describing the relationship between the equilibrium moisture content and water activity in OMW (R (2) = 0.998). During the storage period, the analysis showed an increase of all the physico-chemical parameters studied, except phenols and total phosphorus concentrations. The microbiological study showed the predominance of yeasts and moulds and the decrease of bacteria population after 75 days reflecting both effect of recalcitrant compounds and the water activity on microbial growth.

Review of the Drying Kinetics of Olive Oil Mill Wastes: Biomass Recovery

Directory of Open Access Journals (Sweden)

Francisco J. Gómez-de la Cruz

2015-06-01

Full Text Available The drying kinetics of olive oil mill wastes was analyzed based on experiments carried out by various researchers utilizing different drying systems. A critical review of the literature was done, and mathematical models of drying curves proposed by investigators were evaluated. A comparison between the best mathematical models of fit in the drying curves used in past experiments and a two-term Gaussian model was performed. This model improved all the results of fit in each experiment. Drying rates and drying stages were obtained and discussed. An average drying rate for each experiment from the two-term Gaussian model was calculated. This value allowed for visualizing and comparing the average speed of evaporated water in each experiment for the different dryers. Finally, and after having verified that almost all drying occurs mainly by a diffusion phenomenon, an analysis on the effective moisture diffusivity and activation energy values was performed. The results indicated that there was no dependency of these quantities on independent variables such as the drying air temperature, the drying air velocity, and the sample thickness. It follows that drying of olive oil mill wastes is a very complex physical process that depends heavily on aspects such as pieces of pit, pulp, skin, vegetation water, olive oil content, sugars and organics compounds of different nature.

Modelación del contacto entre dos pares de dientes en las coronas de molinos de caña//Modeling of contact between two pairs of teeth in the sugar cane mills gears

Directory of Open Access Journals (Sweden)

Abdel Mendoza‐Fernández

2013-09-01

Full Text Available En el trabajo se propone un mecanismo equivalente para la modelación del funcionamiento de las coronas de molino de caña de azúcar cuando teóricamente hay dos pares de dientes en contacto. A través del análisis de movilidad del mecanismo se demuestra que no es posible el contacto simultaneo entre dos pares de dientes y que el coeficiente de recubrimiento en estos engranes es igual o menor que la unidad. A partir de los resultados del análisis cinemático del contacto entre un par de dientes, y combinándolo con la modelación del contacto entre dos pares de dientes se demuestra que el coeficiente de recubrimiento real en estos engranajes es menor que la unidad y se producen impactos entre los dientes al inicio del contacto.Palabras claves: molinos de caña, coronas de molinos, coeficiente de recubrimiento, engranajes._________________________________________________________________________________AbstractThe paper proposes an equivalent mechanism for modeling the functioning of the crowns of sugar cane mill when theoretically there are two pairs of teeth in contact. Through mobility analysis of the mechanism is demonstrated that is not possible the simultaneous contact between two pairs of teeth and that the coating coefficient of these gears is equal or less than unity. Combining kinematic analysis results for the contact between a pair of teeth with the modeling the contact between two pairs of teeth, it is demonstrated that gear ratio of these gears is less than unity and impacts occur between the teeth at the start of contact.Key words: sugar cane mills, sugar cane mills gears, contact ratio, gears.

Modelación matemática del funcionamiento de las coronas de molinos considerando la flotación de la maza superior // An equivalent mechanism for the kinetic and dynamic analysis of the sugar cane mill gears

Directory of Open Access Journals (Sweden)

Mario Javier Cabello-Ulloa

2011-08-01

Full Text Available ResumenEn este trabajo se propone un mecanismo equivalente para modelar el funcionamiento de lascoronas de los molinos de caña de azúcar, que permite tomar en cuenta la forma real del perfil de losdientes trazados por arcos de círculos y la variación de la distancia entre centros durante sufuncionamiento. Aplicando el método grafo-analítico al modelo propuesto se obtiene una funcióncinemática que define la posición angular instantánea de la corona conducida con dependencia de ladistancia entre ejes de las ruedas y la posición angular de la corona conductora. Aplicando métodosparamétricos se obtienen ecuaciones para la velocidad y aceleración que son generales paracualquier tipo de perfil de dientes en engranajes que trabajan con variación de distancia entrecentros. Finalmente se grafican estos parámetros para el funcionamiento de las coronas de unmolino real concluyéndose que estas tienen relación de transmisión instantánea variable y que por elsolo hecho de la forma del perfil se producen aceleraciones.Palabras claves: corona de molino, engranaje, mecanismo plano, modelación, cinemática del molino.______________________________________________________________________AbstractEquivalent mechanism is proposed for modeling sugar cane mills gears, which allows to take intoaccount the shape of the tooth profile formed by circular arcs and the variation of the distancebetween centers for operation. Applying the graph-analytical method to the proposed model isobtained a function to define the instantaneous angular position of the sugar cane mill gear in relationwith the instantaneous angular position of driver gear and the center distance of gears. Generalequations for the velocity and acceleration for any type of gear tooth profile with variable distancebetween centers are proposed through parametric method. Plotted these parameters for real sugarcane mill gear and it is concluded that the instantaneous speed ratio is variable

Prospective evaluation for the sugar cane factory transformation in biorefinery

International Nuclear Information System (INIS)

Rodríguez Plaza, Rocío; Armas Martínez, Ana Celia de; Rodríguez Carvajal, Lily Elena; García Orozco, Yamila; Torres, Alfredo

2015-01-01

The present work has as goal to evaluate prospectively alternative of transformation in the '5 de Septiembre' sugar industry, located in Cienfuegos, for a superfine alcohol biorefinery. Two alternatives were taking into account; the first one was the installation of a distillery for a capacity of 500 hl/d of superfine alcohol, using the molasses and 10% of the filters juice coming from the sugar mill, as complement of the stage of fermentation, and also a plant of biodiesel production starting from microalgae biomass and of mud separated in the sugar mill and another installation of a distillery for a similar capacity of 500 Hl/d of superfine ethanol using molasses, the filters juices and microalgae hydrolysate. For the second alternative, it intends a distillery where saving of 67 % for the molasses, and 22.73 % for the water, these results are experimentally obtained. The most feasible alternative obtain 5 years of payback period, 21 % of an IRR and U$D 37104 419.21 of NPV. (author)

Idiomatic Control used in Sugar Plants

DEFF Research Database (Denmark)

Nielsen, Kirsten Mølgaard; Nielsen, Jens Frederik Dalsgaard; Pedersen, Tom Søndergaard

1993-01-01

A description of a control system for a large scale industrial plant - the evaporator section of a sugar plant. The control system is based on the idiomatic control concept, causing decomposition into loop control units - idioms. Dynamic decoupling, feedforward- and feedback loops eg. have been...

Case study: Preliminary assessment of integrated palm biomass biorefinery for bioethanol production utilizing non-food sugars from oil palm frond petiole

International Nuclear Information System (INIS)

Abdullah, Sharifah Soplah Syed; Shirai, Yoshihito; Ali, Ahmad Amiruddin Mohd; Mustapha, Mahfuzah; Hassan, Mohd Ali

2016-01-01

Highlights: • Fermentable sugars production from oil palm frond by integrated technology concept. • Bioethanol production from oil palm frond sugars in a biorefinery. • Palm oil mills have sufficient excess energy and steam to support biorefinery. • The net energy ratio of bioethanol from oil palm frond petiole is 7.48. - Abstract: In this case study, a preliminary assessment on the bioethanol production from oil palm frond (OPF) petiole sugars within an integrated palm biomass biorefinery was carried out. Based on the case study of 4 neighbouring palm oil mills, approximately 55,600 t/y of fermentable sugars could be obtained from OPF petiole. The integrated biorefinery will be located at one of the 4 mills. The mill has potential excess energy comprising 3.64 GW h/y of electricity and 177,000 t/y of steam which are sufficient to run the biorefinery. With 33.9 million litres/y of bioethanol production, the specific production cost of bioethanol is estimated at $ 0.52/l bioethanol, compared to $ 0.31–0.34/l bioethanol produced from sugarcane and $ 0.49–0.60/l bioethanol from other lignocellulosics. The net energy ratio of 7.48 for bioethanol production from OPF provides a promising alternative for OPF utilization as a non-food sugar feedstock.

Fluid flow and particle dynamics inside an evaporating droplet containing live bacteria displaying chemotaxis.

Science.gov (United States)

Thokchom, Ashish Kumar; Swaminathan, Rajaram; Singh, Anugrah

2014-10-21

Evaporation-induced particle deposition patterns like coffee rings provide easy visual identification that is beneficial for developing inexpensive and simple diagnostic devices for detecting pathogens. In this study, the effect of chemotaxis on such pattern formation has been realized experimentally in drying droplets of bacterial suspensions. We have investigated the velocity field, concentration profile, and deposition pattern in the evaporating droplet of Escherichia coli suspension in the presence and absence of nutrients. Flow visualization experiments using particle image velocimetry (PIV) were carried out with E. coli bacteria as biological tracer particles. Experiments were conducted for suspensions of motile (live) as well as nonmotile (dead) bacteria. In the absence of any nutrient gradient like sugar on the substrate, both types of bacterial suspension showed two symmetric convection cells and a ring like deposition of particles after complete evaporation. Interestingly, the droplet containing live bacterial suspension showed a different velocity field when the sugar was placed at the base of the droplet. This can be attributed to the chemoattractant nature of the sugar, which induced chemotaxis among live bacteria targeted toward the nutrient site. Deposition of the suspended bacteria was also displaced toward the nutrient site as the evaporation proceeded. Our experiments demonstrate that both velocity fields and concentration patterns can be altered by chemotaxis to modify the pattern formation in evaporating droplet containing live bacteria. These results highlight the role of bacterial chemotaxis in modifying coffee ring patterns.

VOC Control in Kraft Mills; FINAL

International Nuclear Information System (INIS)

Zhu, J.Y.; Chai, X.-S.; Edwards, L.L.; Gu, Y.; Teja, A.S.; Kirkman, A.G.; Pfromm, P.H.; Rezac, M.E.

2001-01-01

The formation of volatile organic compounds (VOCs), such as methanol, in kraft mills has been an environmental concern. Methanol is soluble in water and can increase the biochemical oxygen demand. Furthermore, it can also be released into atmosphere at the process temperatures of kraft mill-streams. The Cluster Rule of the EPA now requires the control of the release of methanol in pulp and paper mills. This research program was conducted to develop a computer simulation tool for mills to predict VOC air emissions. To achieve the objective of the research program, much effort was made in the development of analytical techniques for the analysis of VOC and determination of vapor liquid partitioning coefficient of VOCs in kraft mill-streams using headspace gas chromatography. With the developed analytical tool, methanol formation in alkaline pulping was studied in laboratory to provide benchmark data of the amount of methanol formation in pulping in kraft mills and for the validation of VOC formation and vapor-liquid equilibrium submodels. Several millwide air and liquid samplings were conducted using the analytical tools developed to validate the simulation tool. The VOC predictive simulation model was developed based on the basic chemical engineering concepts, i.e., reaction kinetics, vapor liquid equilibrium, combined with computerized mass and energy balances. Four kraft mill case studies (a continuous digester, two brownstock washing lines, and a pre-evaporator system) are presented and compared with mill measurements. These case studies provide valuable, technical information for issues related to MACT I and MACT II compliance, such as condensate collection and Clean-Condensate-Alternatives (CCA)

PROSPECTIVE EVALUATION FOR THE SUGAR CANE FACTORY TRANSFORMATION IN BIOREFINERY

Directory of Open Access Journals (Sweden)

Rocío Rodríguez Plaza

2015-10-01

Full Text Available The present work has as goal to evaluate prospectively alternative of transformation in the "5 de Septiembre" sugar industry, located in Cienfuegos, for a superfine alcohol biorefinery. Two alternatives were taking into account; the first one was the installation of a distillery for a capacity of 500 hl/d of superfine alcohol, using the molasses and 10% of the filters juice coming from the sugar mill, as complement of the stage of fermentation, and also a plant of biodiesel production starting from microalgae biomass and of mud separated in the sugar mill and another installation of a distillery for a similar capacity of 500 Hl/d of superfine ethanol using molasses, the filters juices and microalgae hydrolysate. For the second alternative, it intends a distillery where saving of 67 % for the molasses, and 22.73 % for the water, these results are experimentally obtained. The most feasible alternative obtain 5 years of payback period, 21 % of an IRR and U$D 37104 419.21 of NPV.

Energy saving in the sugar cane agroindustry; Ahorro de energia en la agroindustria azucarera canera

Energy Technology Data Exchange (ETDEWEB)

Zedillo Ponce de Leon, Luis [Grupo de paises Latinoamericanos y del Caribe exportadores de azucar (Mexico)

1996-07-01

The traditional sugar mill is inefficient from the energy point of view. Most of the sugar mills were designed to use all the available bagasse, due to the risk of spontaneous ignition and environmental pollution. Consequently, the steam generators, the turbines and other components were designed to work with low efficiencies. Each ton of sugar produced generates a power potential equivalent to four to six oil barrels (bagasse and residues). That is to say, a sugar mill is capable of producing 500 ton/day of sugar, equivalent to an oil well of 2000 to 3000 barrels/day and one thermoelectric power plant of 15,000 kW. Under this context an analysis is made of the sugar mills in Latin America and the Caribbean as one of the ways of increasing their efficiency and obtain great energy savings. As far as steam generation the appropriate use of energy is dictated by the boilers' efficiency. [Spanish] El ingenio azucarero tradicional es ineficiente desde el punto de vista energetico. La mayoria de los ingenios azucareros se disenaron para usar todo el bagazo disponible, debido al riesgo de ignicion espontanea y contaminacion. En consecuencia, los generadores de vapor, las turbinas y demas componentes fueron disenados para trabajar con bajas eficiencias. Cada tonelada de azucar producida genera una potencialidad energetica equivalente de cuatro a seis barriles de petroleo (bagazo y residuos). Es decir, un ingenio capaz de producir 500 ton/dia de azucar equivalente a un pozo de petroleo de 2000 a 3000 barriles/dia y una termoelectrica de 15000 kW. Bajo este contexto se hace un analisis del ingenio azucarero en Latinoamerica y el Caribe como una de las vias para incrementar su eficiencia y lograr grandes ahorros en la energia. En cuanto a generacion de vapor se refiere, el buen uso de la energia viene expresado por la eficiencia de las calderas.

Interior drains for open pit disposal of uranium mill tailings

International Nuclear Information System (INIS)

Staub, W.P.

1978-01-01

A conceptualized interior drainage system is presented for reducing the environmental impact on natural groundwater by disposal of uranium mill tailings in the mined-out open pit. The evaporation/seepage ratio can be increased through the use of interior drains, long-term monitoring of groundwater quality can be eliminated, and the open pit will not require an extensive liner. Other advantages not related to groundwater are: control of fugitive dust and radon emanation during mill operations and timely reclamation after the impoundment is filled with tailings

Fossil energy savings potential of sugar cane bio-energy systems

DEFF Research Database (Denmark)

Nguyen, Thu Lan T; Hermansen, John Erik; Sagisaka, Masayuki

2009-01-01

One important rationale for bio-energy systems is their potential to save fossil energy. Converting a conventional sugar mill into a bio-energy process plant would contribute to fossil energy savings via the extraction of renewable electricity and ethanol substituting for fossil electricity...... and gasoline, respectively. This paper takes a closer look at the Thai sugar industry and examines two practical approaches that will enhance fossil energy savings. The first one addresses an efficient extraction of energy in the form of electricity from the excess bagasse and cane trash. The second while...... proposing to convert molasses or sugar cane to ethanol stresses the use of bagasse as well as distillery spent wash to replace coal in meeting ethanol plants' energy needs. The savings potential achieved with extracting ethanol from surplus sugar versus current practice in sugar industry in Thailand amounts...

Cogeneration alternatives in sugar and alcohol industries. Case of study; Alternativas de cogeracao na industria sucro-alcooleira. Estudo de caso

Energy Technology Data Exchange (ETDEWEB)

Sanchez Prieto, Mario Gabriel

2003-07-01

In the present work, a cogeneration system of sugar-alcohol cane mill is evaluated. Using the Exergetic Cost Theory, a thermo economic analysis is made for the crop corresponding to the year 2000. Previously a detailed energetic analysis was made in order to determine of the first law efficiency for steam boilers and the fuel consumption involved. The first and second law equipment's efficiencies were calculated as well as some performance criteria of the overall system. The fundamental aim of the evaluation was to obtain the cost of the principal fluxes of the system, considering a discount rate of 15 % and a capital recovery period of fifteen years for the energetic equipment in the sugar mill for the monetary cost calculations. In the analysis, was included the sugar mill juice extraction system as a control volume in order to determine the variation in the bagasse cost and its influence in the cost of other fluxes. A Thermodynamic analysis is also made, in which the increase of thermodynamic parameters is studied as a way of improving the fuel economy in Sugar Mill Factories focusing the electric energy obtained in the different alternatives. Diverse strategies are discussed, and as a result, the thermodynamic evaluations of two Proposals of Steam Cogeneration Systems are accomplished as well as the calculations of the exergetic cost. (author)

Cogeneration alternatives in sugar and alcohol industries. Case of study; Alternativas de cogeracao na industria sucro-alcooleira. Estudo de caso

Energy Technology Data Exchange (ETDEWEB)

Sanchez Prieto, Mario Gabriel

2003-07-01

In the present work, a cogeneration system of sugar-alcohol cane mill is evaluated. Using the Exergetic Cost Theory, a thermo economic analysis is made for the crop corresponding to the year 2000. Previously a detailed energetic analysis was made in order to determine of the first law efficiency for steam boilers and the fuel consumption involved. The first and second law equipment's efficiencies were calculated as well as some performance criteria of the overall system. The fundamental aim of the evaluation was to obtain the cost of the principal fluxes of the system, considering a discount rate of 15 % and a capital recovery period of fifteen years for the energetic equipment in the sugar mill for the monetary cost calculations. In the analysis, was included the sugar mill juice extraction system as a control volume in order to determine the variation in the bagasse cost and its influence in the cost of other fluxes. A Thermodynamic analysis is also made, in which the increase of thermodynamic parameters is studied as a way of improving the fuel economy in Sugar Mill Factories focusing the electric energy obtained in the different alternatives. Diverse strategies are discussed, and as a result, the thermodynamic evaluations of two Proposals of Steam Cogeneration Systems are accomplished as well as the calculations of the exergetic cost. (author)

Rentabilidad de la gestión del mantenimiento en los centrales azucareros cubanos. // Maintenance management rentability in Cuban sugar mills.

Directory of Open Access Journals (Sweden)

C. Batista Rodríguez

2003-01-01

Full Text Available Para evaluar de forma acertada la eficiencia de la gestión de mantenimiento en un central azucarero y a su personaldirectivo es necesario disponer de indicadores cuantitativos que reflejen los resultados y la evolución integral del trabajotécnico-organizativo y económico de la actividad. Actualmente existen gran cantidad de indicadores, pero se adolece de lano existencia de un indicador generalizador de la eficiencia de la gestión del mantenimiento, por lo cual es difícil valorarcorrectamente los resultados y la evolución integral de la actividad.En este trabajo se muestra la posibilidad de evaluar de forma integral la eficiencia de la gestión del mantenimiento en loscentrales azucareros cubanos, con el cálculo del indicador Rentabilidad de la gestión del mantenimiento (Rgm.Palabras claves: Gestión de mantenimiento, rentabilidad, eficiencia.________________________________________________________________________________Abstract:In order to properly evaluate the sugar mills maintenance management rentability and its directive personnel there is a needfor cuantitative indicators that reflect results and integral activity evolution. Actually there is a great deal of such indicators,but there is a lack of management maintenance generalizator indicators, making correct results valoration and integralactivity evolution a difficult task. In this paper is exposed the possible evaluation of maintenance management in Cubansugar mills with the Rentability management indicator (Rgm.Key words: Maintenance manegement, rentability, efficiency.

COMPARISON OF VACUUM AND HIGH PRESSURE EVAPORATED WOOD HYDROLYZATE FOR ETHANOL PRODUCTION BY REPEATED FED-BATCH USING FLOCCULATING SACCHAROMYCES CEREVISIAE

Directory of Open Access Journals (Sweden)

Anahita Dehkhoda

2009-02-01

Full Text Available With the aim of increasing the sugars concentration in dilute-acid ligno-cellulosic hydrolyzate to more than 100 g/l for industrial applications, the hydrolyzate from spruce was concentrated about threefold by high-pressure or vacuum evaporations. It was then fermented by repeated fed-batch cultivation using flocculating Saccharomyces cerevisiae with no prior detoxification. The sugars and inhibitors concentrations in the hydrolyzates were compared after the evaporations and also fermenta-tion. The evaporations were carried out either under vacuum (VEH at 0.5 bar and 80°C or with 1.3 bar pressure (HPEH at 107.5°C, which resulted in 153.3 and 164.6 g/l total sugars, respectively. No sugar decomposition occurred during either of the evaporations, while more than 96% of furfural and to a lesser extent formic and acetic acids disappeared from the hydrolyzates. However, HMF and levulinic acid remained in the hydrolyzates and were concentrated proportionally. The concentrated hydrolyzates were then fermented in a 4 l bioreactor with 12-22 g/l yeast and 0.14-0.22 h-1 initial dilute rates (ID. More than 84% of the fermentable sugars present in the VEH were fermented by fed-batch cultivation using 12 g/l yeast and initial dilution rate (ID of 0.22 h-1, and resulted in 0.40±0.01 g/g ethanol from the fermentable sugars in one cycle of fermentation. Fermentation of HPEH was as successful as VEH and resulted in more than 86% of the sugar consumption under the corresponding conditions. By lowering the initial dilution rate to 0.14 h-1, more than 97% of the total fermentable sugars were consumed, and ethanol yield was 0.44±0.01 g/g in one cycle of fermentation. The yeast was able to convert or assimilate HMF, levulinic, acetic, and formic acids by 96, 30, 43, and 74%, respectively.

Generation and export of electric energy by sugar and alcohol plants; Geracao e exportacao de energia eletrica por usinas sucroalcooleiras

Energy Technology Data Exchange (ETDEWEB)

Queiroz, Gil Mesquita de Oliveira Rabello; Paschoareli Junior, Dionizio; Faria Junior, Max Jose de Araujo [Universidade Estadual Paulista (DEE/UNESP), Ilha Solteira, SP (Brazil). Dept. de Engenharia Eletrica. Grupo de Pesquisa em Fontes Alternativas e Aproveitamento de Energia Eletrica

2008-07-01

This paper presents technical aspects necessary to allow a sugar-cane mill, which promotes cogeneration, to operate as an electrical energy producer. Changes and optimization in the process to produce alcohol and sugar-cane, which results in the increase of electrical energy to export are discussed. A case of a sugarcane mill, working as a thermoelectric power plant is presented. The necessary components to generate energy and to connect the thermoelectric plant to the main transmission system are described. (author)

77 FR 54607 - Proclaiming Certain Lands, Sugar Parcel Lands, as an Addition to the Bay Mills Indian Reservation...

Science.gov (United States)

2012-09-05

..., as an Addition to the Bay Mills Indian Reservation for the Bay Mills Indian Community of Michigan... acres, more or less, to be added to the Bay Mills Indian Reservation for the Bay Mills Indian Community... the land described below. The land was proclaimed to be an addition to the Bay Mills Indian...

Produção de açúcar e álcool vs. responsabilidade social corporativa: as ações desenvolvidas pelas usinas de cana-de-açúcar frente às externalidades negativas Sugar and ethanol production vs. corporative social responsibility: the actions taken by the sugar cane mills confronted with negative externalizations

Directory of Open Access Journals (Sweden)

Ivelise Rasera Bragato

2008-04-01

Full Text Available A responsabilidade social corporativa (RSC é analisada neste estudo no ambiente organizacional das usinas de cana-de-açúcar paulistas que integram o agronegócio brasileiro de açúcar e álcool. Trata-se de uma pesquisa qualitativa que utiliza dados quantitativos para fins descritivos. Apoiada em dados secundários e primários, aborda-se um estudo exploratório no contexto das usinas de cana-de-açúcar do Estado de São Paulo. O objetivo geral foi estabelecer uma análise comparativa entre as externalidades negativas e as ações sociais e verificar se estas últimas tinham um papel compensatório. Foi possível identificar a relação entre imagem e RSC no cenário organizacional das usinas, ressaltando as principais ações sociais desenvolvidas pelas empresas, as quais vêm contribuindo para a melhoria da imagem do setor sucroalcooleiro como agente participante do desenvolvimento sustentável. Constatou-se que o foco das ações sociais está concentrado nas áreas educacional e ambiental, ocupando um plano secundário as ações relacionadas à cultura, ao esporte e à saúde. Os resultados demonstraram que o número de projetos sociais não está necessariamente relacionado ao porte das empresas pesquisadas.Corporative Social Responsibility (CSR is analyzed in this study in the organizational environment of sugar cane mills in the state of São Paulo and which form the Brazilian agribusiness of sugar and ethanol. Following a qualitative research, the quantitative data was used to define objectives using the primary and secondary data approach; an exploratory study in the context of the sugar-ethanol mills. The goal was to establish a comparative analysis between the negative external aspects and the social actions to investigate whether the latter had a significant role. It was possible to identify the relation between image and CSR in the organizational scenario of sugar-ethanol mills highlighting the main social actions developed by

FAILURE ANALYSIS IN TUBING OF AIR PREHEATER OF BOILER FROM A SUGARCANE MILL

Directory of Open Access Journals (Sweden)

Joner Oliveira Alves

2014-10-01

Full Text Available The increased demand for energy from sugarcane bagasse has made the sugar and alcohol mills search alternatives to reduce maintenance of the boilers, releasing more time to the production. The stainless steel use has become one of the main tools for such reduction. However, specification errors can lead to premature failures. This work reports the factors that led tubes of AISI 409 stainless steel fail after half season when applied in a air preheater of boiler from a sugarcane mill. In such application, the AISI 304 lasts about 15 seasons and the carbon steel about 3. A tube sent by the sugar mill was characterized by wet chemical analysis, optical microscopy and EDS. Results indicated chloride formation on the internal walls of the tube, which combined with the environment, accelerated the corrosion process. The carbon steel showed high lifetime due to a 70% higher thickness. Due to the work condictions is recommended the use of stainless steels with higher corrosion resistance, such as the traditional AISI 304 or the ferritic AISI 444, the last presents better thermal exchange.

Economical impact of the BIG/CC technology use on the sugar cane industry

Energy Technology Data Exchange (ETDEWEB)

Queiroz, L.C. de; Nascimento, M.J.M. do [Brascep Engenharia Ltda., Rio de Janeiro (Brazil)

1993-12-31

The use of biomass as primary fuel for power and steam production using modern conversion technology such as the Biomass Integrated Gas Turbine/Combined Cycle (BIG/CC) has both technical and commercial potential. Brazil is implementing a BIG/CC Demonstration Plant to burn wood from eucalyptus short rotation forest and to test sugar cane bagasse as feedstock. The purpose of this project is to demonstrate the commercial viability of using biomass as a feedstock for power generation, its suitability for applications in developing countries, and the possibilities it offers for commercial activities in regions which currently have a low level of economic activities. The purpose of this paper is to show the potential applicability of this technology in the sugar cane industries of Developing Countries such as Brazil. The same quantity of sugar cane already processed in each sugar mill can produce sizable quantities of electric power at competitive costs, in addition to the traditional products -- sugar and/or ethanol, which will cause an economical impact, duplicating the revenue of these industries. The application of the BIG/CC technology in the Sugar Cane Industry may lead to the following scenario in developing countries: (1) power shall be produced at very competitive prices by specialized private firms associated with sugar mills; (2) plant sizes will be smaller -- 15 to 100 MW -- when based on biomass, a compared to large fossil fuel plants now prevailing; (3) ethanol and sugar production costs will be reduced due to more efficient and economical processes and due to the additional revenue from power production; (4) becoming more competitive with gasoline, ethanol production tends to increase, which will influence the automobile industry and improve the quality of life in big cities.

Flour mill stream blending affects sugar snap cookie and Japanese sponge cake quality and oxidative cross-linking potential of soft white wheat.

Science.gov (United States)

Ramseyer, Daniel D; Bettge, Arthur D; Morris, Craig F

2011-01-01

The purpose of this research was to study the functional differences between straight grade (75% extraction rate) and patent (60% extraction rate) flour blends from 28 genetically pure soft white and club wheat grain lots, as evidenced by variation in sugar snap cookie and Japanese sponge cake quality. Functional differences were examined relative to arabinoxylan content, protein content, and oxidative cross-linking potential of flour slurries. Oxidative cross-linking measurements were obtained on flour slurries with a low shear Bostwick consistometer and considered endogenous oxidative cross-linking potential (water alone) or enhanced oxidative cross-linking potential (with added hydrogen peroxide-peroxidase). A 2-way ANOVA indicated that flour blend was the greater source of variation compared to grain lot for all response variables except water-extractable arabinoxylan content. Patent flours produced larger sugar snap cookies and Japanese sponge cakes, and contained significantly less total and water-unextractable arabinoxylans, protein, and ash than did straight grade flours. Patent flours produced more viscous slurries for endogenous and enhanced cross-linking measurements compared to the straight grade flours. The functional differences between patent and straight grade flours appear to be related to the particular mill streams that were utilized in the formulation of the 2 flour blends and compositional differences among those streams. Journal of Food Science © 2011 Institute of Food Technologists® No claim to original US government works.

Chemistry Based on Renewable Raw Materials: Perspectives for a Sugar Cane-Based Biorefinery

Directory of Open Access Journals (Sweden)

Murillo Villela Filho

2011-01-01

Full Text Available Carbohydrates are nowadays a very competitive feedstock for the chemical industry because their availability is compatible with world-scale chemical production and their price, based on the carbon content, is comparable to that of petrochemicals. At the same time, demand is rising for biobased products. Brazilian sugar cane is a competitive feedstock source that is opening the door to a wide range of bio-based products. This essay begins with the importance of the feedstock for the chemical industry and discusses developments in sugar cane processing that lead to low cost feedstocks. Thus, sugar cane enables a new chemical industry, as it delivers a competitive raw material and a source of energy. As a result, sugar mills are being transformed into sustainable biorefineries that fully exploit the potential of sugar cane.

Scale up of ethanol production using pulp mill wastewater sludge by cellulase and saccharomyces cerevisiae

International Nuclear Information System (INIS)

Kunchada Sangasintu; Petchporn Chawakitchareon

2010-01-01

This study aimed to evaluate the potential use of pulp mill wastewater sludge as substrate in ethanol production. The simultaneous saccharification and fermentation process was conducted by using Saccharomyces cerevisiae TISTR 5339 under optimum proportion of cellulase and pulp mill wastewater sludge. The ethanol production from cellulosic materials in simultaneous saccharification and fermentation needs cooperation between cellulase and yeast. The cellulase hydrolyzes cellulose to sugar while yeast utilizes sugar to produce ethanol. The pulp mill wastewater sludge has an average content of 73.3 % hemi cellulose, 67.1 % alpha cellulose, 4.7 % beta cellulose and 1.4 % gamma cellulose. The experimental results indicated that the volume of the ethanol tend to increase with time, providing the maximum ethanol yield of 0.69 g/g on the 7"t"h day, the last day of the experiment. The ethanol production was scaled up in 5 L fermentor under optimum proportion and increased the fermentation period. It was found that the ethanol production gave the maximum ethanol yield of 1.14 g/g on the 9"t"h day of the totally 13 days experimentation. These results showed that the cellulose from pulp mill wastewater sludge was as effective substrate for ethanol production and alternative energy for the future. (author)

Biotechnological applications for the utilisation of wastes from palm oil mills

Energy Technology Data Exchange (ETDEWEB)

Cheah, S C; Ma, A N; Ooi, L C.L.; Ong, A S.H.

1988-05-01

The milling of oil palm fruits produces about two-and-a-half to three times as much effluent as oil does. It also generates a large amount of lignocellulosic wastes, mainly in the form of empty fruit bunches, press cake fibres and nut shell. Research efforts at PORIM have been directed towards the utilisation of these wastes as a means to solve the problem of environmental pollution as well as for the generation of economic returns for the mills. We have studied a thermophilic contact process for the anaerobic digestion of palm oil mill effluent and its potential for generating biogas for energy uses. Our work has also shown that the condensate derived from the fruit sterilisation process during milling is amenable to fermentation for the production of single cell protein (SCP) and exo-enzymes. The enzymes produced have been applied for oil clarification, oil recovery from press cake fibers and saccharification of the fibers for the production of sugar feedstocks. This paper will also introduce the concept of integrated waste management for the palm oil mill through the implementation of these technologies.

Releases of radioactivity from uranium mills and effluent treatment costs

International Nuclear Information System (INIS)

Witherspoon, J.P.; Sears, M.B.; Blanco, R.E.

1977-01-01

Airborne releases of radioactive materials from uranium milling to the environment consist of ore dust, yellowcake dust, tailings dust, and radon gas while the mill is active. After a mill has ceased operations, tailings may be stabilized to minimize or prevent airborne releases of radioactive particulates. However, radon gas will continue to be released in amounts inversely proportional to the degree of stabilization treatment (and expense). Liquid waste disposal is by evaporation and natural seepage to the ground beneath the tailings impoundment area. The release of radioactive materials (and potential radiation exposures) determines the majority of costs associated with minimizing the environmental impact of uranium milling. Radwaste treatments to reduce estimated radiation doses to individuals to 3 to 5% of those received with current milling practices are equivalent to $0.66 per pounds of U 3 O 8 and 0.032 mill per kWhr of electricity. This cost would cover a high efficiency reverse jet bag filter and high energy venturi scrubbers for dusts, neutralization of liquids, and an asphalt-lined tailings basin with a clay core dam to reduce seepage. In addition, this increased cost would cover stabilization of tailings, after mill closure, with a 1-in. asphalt membrane topped by 2 ft of earth and 0.5 ft of crushed rock to provide protection against future leaching and wind erosion. The cost of reducing the radiological hazards associated with uranium milling to this degree would contribute about 0.4% to the current total cost of nuclear power

Water reuse from oil mill industries. Reutilizacion de aguas en las industrias de extraccion de aceite de oliva

Energy Technology Data Exchange (ETDEWEB)

Martinez Nieto, L.; Garrido Hoyos, S.E.

1994-01-01

The reuse of oil mill wastewater using a two stages flash evaporator has been studied. The results have been compared between three phases continuous centrifugation and the two phases process. (Author) 4 refs.

Atmospheric sugar alcohols: evaporation rates and saturation vapor pressures

DEFF Research Database (Denmark)

Bilde, Merete; Zardini, Alessandro Alessio; Hong, Juan

alcohols. These polyols are common in the water soluble fraction of atmospheric aerosols. In our experimental system sub-micron particles are generated by nebulization from aqueous solution, and a mono disperse fraction of the aerosol is selected using a differential mobility analyzer. The particles......The atmospheric partitioning between gas and condensed phase of organic molecules is poorly understood, and discrepancies exist between predicted and observed concentrations of secondary organic aerosols. A key problem is the lack of information about thermodynamic properties of semi- and low...... volatile organic molecules. Saturation vapor pressure and the associated temperature dependence (dH) are key parameters for improving predictive atmospheric models. In this work we combine experiments and thermodynamic modeling to investigate these parameters for a series of polyols, so-called sugar...

Fossil energy savings potential of sugar cane bio-energy systems

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Thu Lan T. [Department of Agroecology, Aarhus University, Tjele (Denmark); The Joint Graduate School of Energy and Environment, King Mongkut' s University of Technology Thonburi, Bangkok (Thailand); Hermansen, John E. [Department of Agroecology, Aarhus University, Tjele (Denmark); Sagisaka, Masayuki [Institute of Science for Safety and Sustainability, National Institute of Advanced Industrial Science and Technology, Tsukuba (Japan)

2009-11-15

One important rationale for bio-energy systems is their potential to save fossil energy. Converting a conventional sugar mill into a bio-energy process plant would contribute to fossil energy savings via the extraction of renewable electricity and ethanol substituting for fossil electricity and gasoline, respectively. This paper takes a closer look at the Thai sugar industry and examines two practical approaches that will enhance fossil energy savings. The first one addresses an efficient extraction of energy in the form of electricity from the excess bagasse and cane trash. The second while proposing to convert molasses or sugar cane to ethanol stresses the use of bagasse as well as distillery spent wash to replace coal in meeting ethanol plants' energy needs. The savings potential achieved with extracting ethanol from surplus sugar versus current practice in sugar industry in Thailand amounts to 15 million barrels of oil a year. Whether the saving benefits could be fully realized, however, depends on how well the potential land use change resulting from an expansion of ethanol production is managed. The results presented serve as a useful guidance to formulate strategies that enable optimum utilization of biomass as an energy source. (author)

Development of hemicelluloses biorefineries for integration into kraft pulp mills

Science.gov (United States)

Ajao, Olumoye Abiodun

The development and wide spread acceptance of production facilities for biofuels, biochemicals and biomaterials is an important condition for reducing reliance on limited fossil resources and transitioning towards a global biobased economy. Pulp and paper mills in North America are confronted with high energy prices, high production costs and intense competition from emerging economies and low demand for traditional products. Integrated forest biorefineries (IFBR) have been proposed as a mean to diversify their product streams, increase their revenue and become more sustainable. This is feasible because they have access to forest biomass, an established feedstock supply chain and wood processing experience. In addition, the integration of a biorefinery process that can share existing infrastructure and utilities on the site of pulp mill would significantly lower investment cost and associated risks. Kraft pulping mills are promising receptor processes for a biorefinery because they either possess a prehydrolysis step for extracting hemicelluloses sugars prior to wood pulping or it can be added by retrofit. The extracted hemicelluloses could be subsequently transformed into a wide range of value added products for the receptor mill. To successfully implement hemicelluloses biorefinery, novel processes that are technically and economically feasible are required. It is necessary to identify products that would be profitable, develop processes that are energy efficient and the receptor mill should be able to supply the energy, chemicals and material demands of the biorefinery unit. The objective of this thesis is to develop energy efficient and economically viable hemicelluloses biorefineries for integration into a Kraft pulping process. A dissolving pulp mill was the reference case study. The transformation of hemicellulosic sugars via a chemical and biochemical conversion pathway, with furfural and ethanol as representative products for each pathway was studied. In

Evaporation by mechanical vapor recompression. Technical progress report, September 1-December 31, 1979

Energy Technology Data Exchange (ETDEWEB)

Iverson, C.H.; Coury, G.E.

1979-01-01

Progress to date in the development of a study of the application of the technologies of mechanical vapor recompression and falling film evaporators as applied to the beet sugar industry is reported. Progress is reported in the following areas: technical literature search and plant visitations of existing applications of VR/FFE.

Process for whole cell saccharification of lignocelluloses to sugars using a dual bioreactor system

Science.gov (United States)

Lu, Jue [Okemos, MI; Okeke, Benedict [Montgomery, AL

2012-03-27

The present invention describes a process for saccharification of lignocelluloses to sugars using whole microbial cells, which are enriched from cultures inoculated with paper mill waste water, wood processing waste and soil. A three-member bacterial consortium is selected as a potent microbial inocula and immobilized on inedible plant fibers for biomass saccharification. The present invention further relates the design of a dual bioreactor system, with various biocarriers for enzyme immobilization and repeated use. Sugars are continuously removed eliminating end-product inhibition and consumption by cell.

Effect of milling on DSC thermogram of excipient adipic acid.

Science.gov (United States)

Ng, Wai Kiong; Kwek, Jin Wang; Yuen, Aaron; Tan, Chin Lee; Tan, Reginald

2010-03-01

The purpose of this research was to investigate why and how mechanical milling results in an unexpected shift in differential scanning calorimetry (DSC) measured fusion enthalpy (Delta(fus)H) and melting point (T(m)) of adipic acid, a pharmaceutical excipient. Hyper differential scanning calorimetry (hyper-DSC) was used to characterize adipic acid before and after ball-milling. An experimental study was conducted to evaluate previous postulations such as electrostatic charging using the Faraday cage method, crystallinity loss using powder X-ray diffraction (PXRD), thermal annealing using DSC, impurities removal using thermal gravimetric analysis (TGA) and Karl Fischer titration. DSC thermograms showed that after milling, the values of Delta(fus)H and T(m) were increased by approximately 9% and 5 K, respectively. Previous suggestions of increased electrostatic attraction, change in particle size distribution, and thermal annealing during measurements did not explain the differences. Instead, theoretical analysis and experimental findings suggested that the residual solvent (water) plays a key role. Water entrapped as inclusions inside adipic acid during solution crystallization was partially evaporated by localized heating at the cleaved surfaces during milling. The correlation between the removal of water and melting properties measured was shown via drying and crystallization experiments. These findings show that milling can reduce residual solvent content and causes a shift in DSC results.

Bio-refinery system of DME or CH4 production from black liquor gasification in pulp mills.

Science.gov (United States)

Naqvi, M; Yan, J; Fröling, M

2010-02-01

There is great interest in developing black liquor gasification technology over recent years for efficient recovery of bio-based residues in chemical pulp mills. Two potential technologies of producing dimethyl ether (DME) and methane (CH(4)) as alternative fuels from black liquor gasification integrated with the pulp mill have been studied and compared in this paper. System performance is evaluated based on: (i) comparison with the reference pulp mill, (ii) fuel to product efficiency (FTPE) and (iii) biofuel production potential (BPP). The comparison with the reference mill shows that black liquor to biofuel route will add a highly significant new revenue stream to the pulp industry. The results indicate a large potential of DME and CH(4) production globally in terms of black liquor availability. BPP and FTPE of CH(4) production is higher than DME due to more optimized integration with the pulping process and elimination of evaporation unit in the pulp mill.

Incorporated residues to sugar cone during the industrial processing evaluated by neutron activation analysis

International Nuclear Information System (INIS)

Nadai Fernandes, E.A. de; Bacchi, M.A.

1990-01-01

In the Brazilian sugar and alcohol industry a modern agronomic and industrial technology has been developed during the last years, due to the high demand for sugarcane. The intensive harvest mechanization has increased the soil levels in the cane delivered to the mills despite of the introduced washing systems. Electric welding has been used to recuperate the rollers of the mill and other metallic components thus increasing the contents of metals in the processed material. Samples of cane, juice and bagasse were colected at several points of the milling tandem and submitted to neutron activation analysis. The concentrations of Fe, Cr, Co, Zn, Br and Cs showed an increment through the mill, indicating the contribution of the rollers wear. Sc and the rare earth elements La, Ce, Sm and Eu had about the same levels in all samples, therefore they must have come with the soil adhered to the cane. (author)

Effect of steam pretreatment on oil palm empty fruit bunch for the production of sugars

International Nuclear Information System (INIS)

Shamsudin, Saleha; Md Shah, Umi Kalsom; Zainudin, Huzairi; Abd-Aziz, Suraini; Mustapa Kamal, Siti Mazlina; Shirai, Yoshihito; Hassan, Mohd Ali

2012-01-01

Lignocellulose into fuel ethanol is the most feasible conversion route strategy in terms of sustainability. Oil palm empty fruit bunch (EFB) generated from palm oil production is a huge source of cellulosic material and represents a cheap renewable feedstock which awaits further commercial exploitation. The purpose of this study was to investigate the feasibility of using steam at 0.28 MPa and 140 °C generated from the palm oil mill boiler as a pretreatment to enhance the digestibility of EFB for sugars production. The effects of steam pretreatment or autohydrolysis on chemical composition changes, polysaccharide conversion, sugar production and morphology alterations of four different types of EFB namely fresh EFB (EFB1), sterilized EFB (EFB2), shredded EFB (EFB3) and ground EFB (EFB4) were evaluated. In this study, the effects of steam pretreatment showed major alterations in the morphology of EFB as observed under the scanning electron microscope. Steam pretreated EFB2 was found to have the highest total conversion of 30% to sugars with 209 g kg −1 EFB. This production was 10.5 fold higher than for EFB1 and 1.6 fold and 1.7 fold higher than EFB3 and EFB4, respectively. The results suggested that pretreatment of EFB by autohydrolysis using steam from the mill boiler could be considered as being a suitable pretreatment process for the production of sugars. These sugars can be utilized as potential substrates for the production of various products such as fuel ethanol. -- Highlights: ► We investigate the feasibility of steam pretreatment to enhance digestibility of EFB. ► Steam pretreatment increased sugars to 3.4 fold and caused major alteration in EFB morphology under SEM. ► Autohydrolysis which does not require the addition of chemicals is an attractive pretreatment approach to EFB.

Enhancing the enzymatic hydrolysis of corn stover by an integrated wet-milling and alkali pretreatment.

Science.gov (United States)

He, Xun; Miao, Yelian; Jiang, Xuejian; Xu, Zidong; Ouyang, Pingkai

2010-04-01

An integrated wet-milling and alkali pretreatment was applied to corn stover prior to enzymatic hydrolysis. The effects of NaOH concentration in the pretreatment on crystalline structure, chemical composition, and reducing-sugar yield of corn stover were investigated, and the mechanism of increasing reducing-sugar yield by the pretreatment was discussed. The experimental results showed that the crystalline structure of corn stover was disrupted, and lignin was removed, while cellulose and hemicellulose were retained in corn stover by the pretreatment with 1% NaOH in 1 h. The reducing-sugar yield from the pretreated corn stovers increased from 20.2% to 46.7% when the NaOH concentration increased from 0% to 1%. The 1% NaOH pretreated corn stover had a holocellulose conversion of 55.1%. The increase in reducing-sugar yield was related to the crystalline structure disruption and delignification of corn stover. It was clarified that the pretreatment significantly enhanced the conversion of cellulose and hemicellulose in the corn stover to sugars.

Production of sugar and alcohol: financial and operational strategies

Directory of Open Access Journals (Sweden)

Celma de Oliveira Ribeiro

2014-12-01

Full Text Available This article proposes the construction of an optimization model to define the product portfolio of a sugarcane mill, taking into account operational and financial aspects. It is considered that the revenue earned by a producer comes from the sale of sugar and alcohol in the physical market and the results obtained through hedging in the derivatives market of sugar. Employing CVaR (Conditional Value-at-Risk, as the risk measure, the model allows the construction of an efficient frontier and, according to the producer's risk tolerance, defines the optimal strategy of production (production mix and activity in the derivatives market (hedge ratio. Through the model the article also seeks to analyze the advantage of using the options market in the construction of financial hedging strategies in agricultural commodities markets.

Uranium ore mill at Dolni Rozinka: 40 years of operation

International Nuclear Information System (INIS)

Toman, F.; Jezova, V.

2007-01-01

Uranium ore mined in the Rozna deposit is treated at a chemical treatment plant (a mill) situated in the close vicinity of the Rozna mine. In the mill, uranium is extracted from the crushed and ground-up ore by alkaline leaching. Uranium is then recovered from the solution by sorption on ion exchange resin; the next steps are precipitation and drying. Alkaline leaching is applied at the atmospheric pressure and the temperature of 80 deg C; the recovery factor is moving around 93%. The final product of the milling is uranium concentrate, ammonium diuranate (NH 4 ) 2 U 2 O 7 ), a so-called 'yellow cake' which is treated into a fuel for nuclear power plants in conversion facilities abroad. The milling is carried on under the condition of the closed cycle of technology water. Due to the positive annual precipitation balance, the over balance of technology water in tailings pond has to be purified before discharging into a river. Evaporation and membrane processes (electrodialysis and reverse osmosis) are used to purify the water. The mill at Dolni Rozinka has been in operation since 1968. It has processed 13.2 million tons of uranium ore which is about 14000 tons of uranium and purified more than 6 million m 3 of the over balanced technology water during 40 years. From the organizational point of view, the mine and the chemical treatment plant form the branch plant GEAM, which is a part of the state enterprise DIAMO. (author)

Nectar sugar composition of European Caryophylloideae (Caryophyllaceae) in relation to flower length, pollination biology and phylogeny.

Science.gov (United States)

Witt, T; Jürgens, A; Gottsberger, G

2013-10-01

Floral nectar composition has been explained as an adaptation to factors that are either directly or indirectly related to pollinator attraction. However, it is often unclear whether the sugar composition is a direct adaptation to pollinator preferences. Firstly, the lower osmolality of sucrose solutions means that they evaporate more rapidly than hexose solutions, which might be one reason why sucrose-rich nectar is typically found in flowers with long tubes (adapted to long-tongued pollinators), where it is better protected from evaporation than in open or short-tubed flowers. Secondly, it can be assumed that temperature-dependent evaporation is generally lower during the night than during the day so that selection pressure to secrete nectar with high osmolality (i.e. hexose-rich solutions) is relaxed for night-active flowers pollinated at night. Thirdly, the breeding system may affect selection pressure on nectar traits; that is, for pollinator-independent, self-pollinated plants, a lower selective pressure on nectar traits can be assumed, leading to a higher variability of nectar sugar composition independent of pollinator preferences, nectar accessibility and nectar protection. To analyse the relations between flower tube length, day vs. night pollination and self-pollination, the nectar sugar composition was investigated in 78 European Caryophylloideae (Caryophyllaceae) with different pollination modes (diurnal, nocturnal, self-pollination) using high-performance liquid chromatography (HPLC). All Caryophylleae species (Dianthus and relatives) were found to have nectar with more than 50% sucrose, whereas the sugar composition of Sileneae species (Silene and relatives) ranged from 0% to 98.2%. In the genus Silene, a clear dichotomous distribution of sucrose- and hexose-dominant nectars is evident. We found a positive correlation between the flower tube length and sucrose content in Caryophylloideae, particularly in day-flowering species, using both conventional

Prospects of sugarcane milling waste utilization for hydrogen production in India

International Nuclear Information System (INIS)

Singh, S.P.; Asthana, R.K.; Singh, A.P.

2007-01-01

Cane-sugar producing countries also generate sufficient waste (bagasse) that is mostly utilized ''on-site'' as a replacement to coal in specialized boilers. In addition to sugar and molasses, about 25% by-product of the cane milling is bagasse that still retains 2.5% sugar on dry wt. basis.This paper deals with the prospects of bagasse fermentation for hydrogen production. It seems relevant, as India and Brazil are the major sugarcane producers in the world. The results obtained confirm bagasse, annually generated to a tune of 40 Mt (million tons) in India, can be diverted from the conventional burning or composting to fermentative hydrogen production in a cost-effective way. The processing cost of bagasse for hydrogen production (3Nm 3 ) equivalent to 1L petrol is about half. The system optimization for accessibility of polysaccharides in bagasse and the use of genetically efficient bacterial strains for agrowaste-based hydrogen production seems the ideal option for clean energy generation

Evaporation

International Nuclear Information System (INIS)

Delaney, B.T.; Turner, R.J.

1989-01-01

Evaporation has long been used as a unit operation in the manufacture of various products in the chemical-process industries. In addition, it is currently being used for the treatment of hazardous wastes such as radioactive liquids and sludges, metal-plating wastes, and other organic and inorganic wastes. Design choice is dependent on the liquid to be evaporated. The three most common types of evaporation equipment are the rising-film, falling-film, and forced-circulation evaporators. The first two rely on boiling heat transfer and the latter relies on flash vaporization. Heat exchangers, flash tanks, and ejectors are common auxiliary equipment items incorporated with evaporator bodies to complete an evaporator system. Properties of the liquid to be evaporated are critical in final selection of an appropriate evaporator system. Since operating costs are a significant factor in overall cost, heat-transfer characteristics and energy requirements are important considerations. Properties of liquids which are critical to the determination of final design include: heat capacity, heat of vaporization, density, thermal conductivity, boiling point rise, and heat-transfer coefficient. Evaporation is an expensive technology, both in terms of capital costs and operating costs. Additionally, mechanical evaporation produces a condensate and a bottoms stream, one or both of which may require further processing or disposal. 3 figs

Evaporation, diffusion and self-assembly at drying interfaces.

Science.gov (United States)

Roger, K; Sparr, E; Wennerström, H

2018-04-18

Water evaporation from complex aqueous solutions leads to the build-up of structure and composition gradients at their interface with air. We recently introduced an experimental setup for quantitatively studying such gradients and discussed how structure formation can lead to a self-regulation mechanism for controlling water evaporation through self-assembly. Here, we provide a detailed theoretical analysis using an advection/diffusion transport equation that takes into account thermodynamically non-ideal conditions and we directly relate the theoretical description to quantitative experimental data. We derive that the concentration profile develops according to a general square root of time scaling law, which fully agrees with experimental observations. The evaporation rate notably decreases with time as t-1/2, which shows that diffusion in the liquid phase is the rate limiting step for this system, in contrast to pure water evaporation. For the particular binary system that was investigated experimentally, which is composed of water and a sugar-based surfactant (α-dodecylmaltoside), the interfacial layer consists in a sequence of liquid crystalline phases of different mesostructures. We extract values for mutual diffusion coefficients of lamellar, hexagonal and micellar cubic phases, which are consistent with previously reported values and simple models. We thus provide a method to estimate the transport properties of oriented mesophases. The macroscopic humidity-independence of the evaporation rate up to 85% relative humidities is shown to result from both an extremely low mutual diffusion coefficient and the large range of water activities corresponding to relative humidities below 85%, at which the lamellar phase exists. Such a humidity self-regulation mechanism is expected for a large variety of complex system.

Sugars profiles of different chestnut (Castanea sativa Mill.) and almond (Prunus dulcis) cultivars by HPLC-RI.

Science.gov (United States)

Barreira, João C M; Pereira, José Alberto; Oliveira, M Beatriz P P; Ferreira, Isabel C F R

2010-03-01

Sugar profiles of different almond and chestnut cultivars were obtained by high-performance liquid chromatography (HPLC), by means of a refractive index (RI) detector. A solid-liquid extraction procedure was used in defatted and dried samples. The chromatographic separation was achieved using a Eurospher 100-5 NH(2) column using an isocratic elution with acetonitrile/water (70:30, v/v) at a flow rate of 1.0 ml/min. All the compounds were separated in 16 min. The method was optimized and proved to be reproducible and accurate. Generally, more than 95% of sugars were identified for both matrixes. Sugars profiles were quite homogeneous for almond cultivars; sucrose was the main sugar (11.46 +/- 0.14 in Marcona to 22.23 +/- 0.59 in Ferragnes g/100 g of dried weight), followed by raffinose (0.71 +/- 0.05 in Ferraduel to 2.11 +/- 0.29 in Duro Italiano), glucose (0.42 +/- 0.12 in Pegarinhos two seeded to 1.47 +/- 0.19 in Ferragnes) and fructose (0.11 +/- 0.02 in Pegarinhos two seeded to 0.59 +/- 0.05 in Gloriette). Commercial cultivars proved to have higher sucrose contents, except in the case of Marcona. Nevertheless, chestnut cultivars revealed a high heterogeneity. Sucrose was the main sugar in Aveleira (22.05 +/- 1.48), Judia (23.30 +/- 0.83) and Longal (9.56 +/- 0.91), while glucose was slightly prevalent in Boa Ventura (6.63 +/- 0.49). The observed variance could serve for inter-cultivar discrimination.

Programação estocástica robusta aplicada ao planejamento agregado de safra em usinas cooperadas do setor sucroenergético Stochastic robust optimization model applied to the aggregate production planning in mill cooperative socities in the sugar-energy sector

Directory of Open Access Journals (Sweden)

Rafael Piatti Oiticica de Paiva

2011-01-01

Full Text Available Neste trabalho, apresenta-se um modelo de programação estocástica robusta aplicado ao planejamento agregado da produção em usinas cooperadas do setor sucroenergético. Esta modelagem considera a relação hierárquica existente entre o planejamento anual da cooperativa e o planejamento tático de safra das usinas cooperadas, além de contemplar importantes incertezas existentes nos parâmetros de entrada do modelo. Para resolver os problemas de programação linear e programação inteira mista envolvidos, utiliza-se uma linguagem de modelagem algébrica e um software de última geração de programação matemática. Os resultados computacionais obtidos são comparados aos resultados da modelagem determinística PASUC, discutida em Paiva e Morabito (in press, utilizando os mesmos dados do estudo de caso da Usina Santa Clotilde e da Cooperativa Regional dos Produtores de Açúcar e Álcool de Alagoas.This work presents a stochastic robust optimization model applied to the aggregate production planning in mill cooperative societies in the sugar-energy sector This mathematical model is based on a hierarchical relationship between the annual planning of the cooperative and the tactical planning horizon of the sugarcane mills taking into account important uncertainties in several parameters of this model. In order to solve the linear and mixed integer programming problems involved, an optimization modeling language solver was used. Computational results are presented and compared with the deterministic approach PASUC, dicussed by Paiva e Morabito (in press using the same data from the case studies conducted in the Santa Clotilde milling company and in the regional cooperative society of sugar and ethanol producers of Alagoas.

Effects of Evaporation Pressure and the Variety of Cane on the Quality of Sugar Honey and Panela

Directory of Open Access Journals (Sweden)

Luz Esperanza Prada Forero

2015-07-01

Full Text Available When multi-effect evaporators (EME are implemented at the process of panela —besides of technological adjustment— to maintain the quality of the product is also required. This state unveiled a technolog y gap, and issues such as the contribution of compositional differences in the varieties of cane on panela. To fill part of this technological gap, the objective of this work is to determine the effect of pressure evaporation and the varieties of cane on quality of honey and panela. To achieve this, the evaporation pressure and sugarcane varieties in one experimental design completely randomized with 4x3 factorial arrangement and four replications was implemented: varieties CC 85-46, RD 75-11 andPR 61-632, without flocculant, without coadjuvant and was evaporated with a heat flux of 27,778 kW/m2 and without antifoam. The results showed a similar behavior for the studied sugarcane varieties. So honeys and panelas in the pressurized system presented dark coloration, reddish tone, high turbidity, a glycoside coefficient between 60 % and 70 % and they did not solidified. Honeys and panelas in vacuum systems presented a greater turbidity, clear colorations, yellowish tones, and good solidification and coefficients glycosides under 12 %.

Treatment of Olive Mill Wastewater and the Use of Polyphenols Obtained After Treatment

Directory of Open Access Journals (Sweden)

Semih Otles

2012-04-01

Full Text Available Olive mill wastes are signicant environmental problem especially in Mediterranean areas where they are generated in huge quantities in a short period of time. They are phytotoxic materials because of their high phenol, lipid and organic acid concentrations, but these wastes also contain valuable resources that could be recycled such as a large proportion of organic matter and a wide range of nutrients. The effluent from olive oil mills contains a large amount of polyphenols that have antioxidant properties. The market value of these antioxidants is high and they are commonly used in the food, cosmetics, pharmaceutics and chemical industries. For the management of olive mill wastewater (OMW and other olive residues, various treatment methods can be used. Many scientists work on more efficient and cheaper treatment alternatives. Due to the great variety of compounds in the waste, several technologies to remove the harmful compounds for the environment should be used single or together. Some of the most used OMW treatments are drying / evaporation, forced evaporation, thermal treatment, centrifugation-ultraltration, electrocoagulation, composting, lagooning, adsorption, powdered activated carbon, filtration, sand filtration, membrane filtration, ultrafiltration, precipitation / flocculation, distillation, electrolysis, co-composting, advanced oxidation processes (AOPs such as ozonation, hydrogen peroxide / ferrous iron oxidation (the so-called Fentons reagent. Several OMW treatment technologies have been developed aiming at the removal of the main toxic organic compounds. A lot of factors must be considered to choose the treatment methods among them the investment, required area, specic training of the workers, noise and odour emissions and seasonality of production.

Economic analyse of industrial production and electric energy consumption on a sugar-alcohol plant; Analise economica da producao industrial e do consumo de energia eletrica em uma usina sucro-alcooleira

Energy Technology Data Exchange (ETDEWEB)

Bini, Aderson

1993-10-01

Economic aspects of industrial production of sugar cane and automotive alcohol fuel, the relation between its production and electric energy consumption, electric energy costs to self generated electric power and concessionary supply, involved in plant production on Ribeirao Preto, SP, Brazil, are presented. Studies to verify the relationships between sugar and alcohol production with milling ours as well as sugar cane processed with sugar and alcohol produced are also discussed 27 refs., 12 figs., 38 tabs.

Ferti-irrigational impact of sugar mill effluent on agronomical characteristics of Phaseolus vulgaris (L.) in two seasons.

Science.gov (United States)

Kumar, Vinod; Chopra, A K

2014-11-01

Ferti-irrigation response of 5, 10, 25, 50, 75, and 100 % concentrations of the sugar mill effluent (SME) on French bean (Phaseolus vulgaris L., cv. Annapurna) in the rainy and summer seasons was investigated. The fertigant concentrations produced significant (P potassium (K(+)), calcium (Ca(2+)), magnesium (Mg(2+)), total Kjeldahl nitrogen (TKN), phosphate (PO4 (3-)), sulfate (SO4 (2-)), ferrous (Fe(2+)), cadmium (Cd), chromium (Cr), copper (Cu), manganese (Mn), and zinc (Zn), in both seasons. The contents of Cr, Cu, Mn, and Zn except Cd were found to be below the maximum levels permitted for soils in India. The agronomic performance of P. vulgaris was gradually increased at lower concentrations, i.e., from 5 to 25 %, and decreased at higher concentrations, i.e., from 50 to 100 %, of the SME in both seasons when compared to controls. The accumulations of heavy metals were increased in the soil and P. vulgaris from 5 to 100 % concentrations of the SME in both seasons. The contents of Cu, Mn, and Zn except Cd and Cr were noted under the permissible limit of Food and Agriculture Organization (FAO)/World Health Organization (WHO) standards. Most contents of biochemical components like crude proteins, crude fiber, and total carbohydrates were found with 25 % concentration of the SME in both seasons. The contamination factor (Cf) of various metals was in the order of Cd > Cr > Zn > Mn > Cu for soil and Mn > Zn > Cu > Cr > Cd for P. vulgaris in both seasons after fertigation with SME. Therefore, the SME can be used to improve the soil fertility and yield of P. vulgaris after appropriate dilution.

Automated Temperature Control with Adjusting Outlet Valve of Fuel in the Process of Cooking Palm Sugar

Science.gov (United States)

Aripin, H.; Hiron, Nurul; Priatna, Edvin; Busaeri, Nundang; Andang, Asep; Suhartono; Sabchevski, Svilen

2018-04-01

In this paper, a real-time temperature control system for coconut sugar cooking is presented. It is based on a thermocouple temperature sensor. The temperature in the closed evaporator is used as a control variable of the DC servo control system for opening and closing of a valve embedded in a gas burner. The output power level, which is necessary in order to reach the target temperature is controlled by the microcontroller ATMega328P. A circuit module for control of the valve and temperature sensors as well as software for data acquisition have been implemented. The test results show that the system properly stabilizes the temperature in the closed evaporator for coconut sugar cooking in the range from room temperature to 110°C. A set point can be reached and held with an accuracy of ±0.75°C at a temperature of 110°C for 60 minutes.

Effect of amendments on chemical immobilization of heavy metals in sugar mill contaminated soils

Directory of Open Access Journals (Sweden)

Mohammad Jamal Khan, Muhammad Tahir Azeem and Sajida Perveen1

2012-05-01

Full Text Available A bulk soil sample collected from the vicinity of PSM (Premier Sugar Mill Mardan was amended with diammonium phosphate (DAP, triple super phosphate (TSP, Farm Yard Manure (FYM and poultry manure (PM in 1.5 kg soil in a 2 L plastic pot. Both DAP and TSP were added at 230 mg kg 1 (460 kg ha 1 soil whereas the organic amendments (FYM and PM were added at the rate of 10% by weight of soil. The air dried samples in pots were brought to field moisture content (0.33 bar water content by the addition of either HIE (Hayatabad Industrial Estate or PSM in two separate sets of experiments. The experimental pots were arranged in randomized complete design with three replicates under laboratory conditions during March to May (Temperature varying between 25 to 30 °C. Treated and control pots were incubated for 90 days al 0.33 bar ca 25% moisture and the moisture deficit during the incubation time was adjusted by adding PSM and HIE effluents in their respective set of experimental pots. Soil samples were collected after 15, 30, 45 and 90 d to determine the effect of amendments on AB-DTPA extractable metals. The results showed that AB-DTPA extractable Cd, Or, Cu, Ni and Cd increased significantly with lime and the maximum values were noted after 90 days incubation whereas the Fe, Mn and Zn content in soil increased with time but the increase was not significant. It was further noted that the increase over time in metal was not pronounced when supplied with amendments indicating their ability to chemically stabilize it compared to unamended soils. Higher values of all the heavy metals were noted in unamended soil. By comparing the different amendments, it was observed that FYM was effective in reducing the extractability/phytoavailability of all the metals under study except Pb whereby DAP was most effective as a stabilizing agent in the soil. It was concluded that in calcareous soil, FYM and DAP can be used to reduce the risk of phytotoxicity of heavy metals in

Greenhouse gasses emissions and energy balances of a non-vertically integrated sugar and ethanol supply chain: A case study in Argentina

International Nuclear Information System (INIS)

Acreche, Martín M.; Valeiro, Alejandro H.

2013-01-01

In order to address society's concerns regarding the sustainability of sugar and ethanol production and use, this paper calculates the energy and greenhouse gasses (GHG) emissions' balances of a non-vertically integrated sugarcane industry in Tucumán-Argentina. The essential operations involved in the sugar/ethanol production cycle were taken into account. Results show that this industry generated an energy balance of 3.4:1. GHG emissions during sugarcane production were 1824 and 2231 kg CO 2 eq. ha −1 year −1 for low and middle to high farms' technological levels, respectively. The mill process emitted 1187 kg CO 2 eq. ha −1 year −1 . The main factors influencing these balances were gas-oil and nitrogen fertilizers used in the agricultural stage, natural gas consumed by the sugar mill, and sugarcane burning (only for GHG balance). The impact of ethanol use in reducing GHG emissions under the current production scheme (6.8 Mg ha −1 of sugar + 380.9 kg ha −1 of ethanol), in final blends of 95% gasoline and 5% ethanol in vehicles, is negligible. A sensitivity analysis indicates that switching to 100% bagasse used as fuel in mill's boilers, ethanol being produced directly from sugarcane juice, and a final blend of 90% gasoline and 10% ethanol, an amount of 1746 kg CO 2 eq. ha −1 year −1 of GHG emissions could be avoided. - Highlights: ► Energy and GHG emissions' balances for the non-integrated sugar/ethanol industry in Tucumán-Argentina. ► The energy balance was positive, while there were important GHG emissions. ► Factors influencing both balances were gas-oil, N fertilizers, burning and natural gas. ► Ethanol use for reducing GHG emissions in the current production scheme is negligible. ► Results are promising, as the main factors influencing both balances are identified

Value Added Products from Hemicellulose Utilization in Dry Mill Ethanol Plants

Energy Technology Data Exchange (ETDEWEB)

Rodney Williamson, ICPB; John Magnuson, PNNL; David Reed, INL; Marco Baez, Dyadic; Marion Bradford, ICPB

2007-03-30

The Iowa Corn Promotion Board is the principal contracting entity for this grant funded by the US Department of Agriculture and managed by the US Department of Energy. The Iowa Corn Promotion Board subcontracted with New Jersey Institute of Technology, KiwiChem, Pacific Northwest National Lab and Idaho National Lab to conduct research for this project. KiwiChem conducted the economic engineering assessment of a dry-mill ethanol plant. New Jersey Institute of Technology conducted work on incorporating the organic acids into polymers. Pacific Northwest National Lab conducted work in hydrolysis of hemicellulose, fermentation and chemical catalysis of sugars to value-added chemicals. Idaho National Lab engineered an organism to ferment a specific organic acid. Dyadic, an enzme company, was a collaborator which provided in-kind support for the project. The Iowa Corn Promotion Board collaborated with the Ohio Corn Marketing Board and the Minnesota Corn Merchandising Council in providing cost share for the project. The purpose of this diverse collaboration was to integrate the hydrolysis, the conversion and the polymer applications into one project and increase the likelihood of success. This project had two primary goals: (1) to hydrolyze the hemicellulose fraction of the distillers grain (DG) coproduct coming from the dry-mill ethanol plants and (2) convert the sugars derived from the hemicellulose into value-added co-products via fermentation and chemical catalysis.

Effect of the milling conditions on the degree of amorphization of selenium by milling in a planetary ball mill

International Nuclear Information System (INIS)

Ksiazek, K; Wacke, S; Gorecki, T; Gorecki, Cz

2007-01-01

The effect of the milling parameters (rotation speed of the milling device and duration of milling) on the phase composition of the products of milling of fully crystalline selenium has been investigated. The milling was conducted using a planetary micromill and the phase composition of the milling products was determined by differential thermal analysis. It has been found that ball milling leads to the partial amorphization of the starting crystalline material. The content of amorphous phase in the milling products depends, in a rather complicated way, on the milling parameters. At the milling parameters adopted in the present study, the milling product was never fully amorphous. The complicated way the milling parameters affect the content of amorphous phase in the milling products is a result of competition of two processes: amorphization due to deformation and refinement of grains of milled material and crystallization of the already produced amorphous material at the cost of heat evolved in the milling vial during the milling process

The electricity cogeneration in sugar mills and alcohol and the reduction of emissions of greenhouse gases

International Nuclear Information System (INIS)

Valdés Delgado, Antonio

2015-01-01

Electric power in Cuba currently produces -in high proportion- plants employing fossil fuel. The price of fossil fuels and the negative influence on the environment by emissions of greenhouse gases, has indicated the need to develop other energy sources. Biomass sugarcane provides ample opportunities to produce this energy with positive economic and environmental results. The technological process for the production of sugar requires the use of mechanical energy, low power consumption compared to thermal energy requirements and their use at low pressures determine the possibility of implementing a cogeneration system of mechanical, thermal and electrical energy. The power consumption for the driving equipment of a factory is about 15-30 kw-kr / ton rod. The amount of electrical energy generated in a sugar cane factory is sufficient to meet their own needs, being able to obtain an additional amount for supply to the public network and meet the needs of other productions as is alcohol. Agricultural crop residues (RAC) and sugarcane bagasse and a liquid fuel: alcohol and gaseous fuel: different energy possibilities derived from the sugar industry reflected in the disposal of solid fuels such as is the biogas. The preparation of solid, liquid and gaseous fuels from sugar and alcohol production avoids the use of fossil fuels such as gasoline and fuel oil and gas enables not be sent into the atmosphere that impact on the greenhouse effect. (full text)

Um modelo de otimização para o planejamento agregado da produção em usinas de açúcar e álcool An optimization model for the aggregate production planning in alcohol and sugar mills

Directory of Open Access Journals (Sweden)

Rafael Piatti Oititica de Paiva

2007-04-01

Full Text Available Neste trabalho apresentamos um modelo de otimização para o planejamento agregado da produção de usinas de açúcar e álcool. Este modelo se baseia nos modelos clássicos de seleção de processos e dimensionamento de lotes para representar o sistema de produção de açúcar, álcool e melaço, incluindo decisões da etapa agrícola, das fases de corte, carregamento e transporte de cana e, principalmente, decisões de moagem, escolha do processo produtivo e estoque dos produtos finais. As decisões são tomadas em períodos semanais e o horizonte de planejamento são as semanas de safra. Para resolver o modelo de programação linear inteira mista resultante, utilizamos a linguagem de modelagem GAMS e o solver CPLEX. Um estudo de caso foi realizado em uma usina de açúcar e álcool do estado de Alagoas. Neste estudo foi possível verificar a adequação do modelo proposto quando aplicado para auxiliar nas decisões envolvidas no planejamento agregado da produção de empresas deste tipo. Resultados computacionais são apresentados resolvendo um exemplo com dados de uma safra típica.The main concern of this work is related to the presentation of an aggregate production planning model of a sugar and alcohol milling company. The mathematical model is based on the process selection model and the production lot-sizing model, and aims to help the decision makers in the production planning and control process of determining the quantity of sugarcane crushed, the selection of sugarcane suppliers, the selection of sugarcane transport system suppliers, the selection of industrial process used in the sugar, alcohol and molasses production and the storage decisions related to these final products. The decisions are taken on a weekly basis and the planning horizon is the whole sugarcane harvesting season. To solve the mixed integer mathematical problem found in this model, we applied the GAMS modeling language and the CPLEX solver. A case study was

The Value of the Freshwater Snail Dip Scoop Sampling Method in Macroinvertebrates Bioassessment of Sugar Mill Wastewater Pollution in Mbandjock, Cameroon

Directory of Open Access Journals (Sweden)

Emmanuel Noumi

2008-03-01

Full Text Available Macroinvertebrates identification and enumeration may be used as a simple and affordable alternative to chemical analysis in water pollution monitoring. However, the ecological responses of various taxa to pollution are poorly known in resources-limited tropical countries. While freshwater macroinvertebrates have been used in the assessment of water quality in Europe and the Americas, investigations in Africa have mainly focused on snail hosts of human parasites. There is a need for sampling methods that can be used to assess both snails and other macroinvertebrates. The present study was designed to evaluate the usefulness of the freshwater snail dip scoop method in the study of macroinvertebrates for the assessment of the SOSUCAM sugar mill effluents pollution. Standard snail dip scoop samples were collected upstream and downstream of the factory effluent inputs, on the Mokona and Mengoala rivers. The analysis of the macroinvertebrate communities revealed the absence of Ephemeroptera and Trichoptera, and the thriving of Syrphidae in the sections of the rivers under high effluent load. The Shannon and Weaver diversity index was lower in these areas. The dip scoop sampling protocol was found to be a useful method for macroinvertebrates collection. Hence, this method is recommended as a simple, cost-effective and efficient tool for the bio-assessment of freshwater pollution in developing countries with limited research resources.

BUSINESS OPPORTUNITIES OF CITRIC ACID PRODUCTION BY FERMENTATION FROM SUGAR SUBSTRATES IN CUBA

Directory of Open Access Journals (Sweden)

Omar Pérez Navarro

2016-04-01

Full Text Available A proposal for opportunities of citric acid production in Cuba, using sources of sugar substrates such as refined sugar, molasses and whey, by submerged fermentation with Aspergillus niger, where a technology is established from the selected substrate which is provided and the microorganism used. This is a demanding process in terms of investment costs and operation where the best combinations of productivity and cost are achieved with molasses followed by refined sugar and whey. For the selected substrate, the mass and energy balance in each of the steps in the process of obtaining citric acid for different productive capacities of citric acid was made and the minimum economic size of 2.5 t / day was determined. A production capacity of 8 t / day of granulated acid (2 640 t / a, with estimated total investment of $ 9,068,713, NPV = $ 1,401,561, IRR = 27% and DPP = 3 years was selected. The project is resistant to the rising price of raw materials and the cost of electricity and is favored when the process is integrated into a sugar mill cogeneration, while it is sensitive to a reduction in the selling price of the product.

TECHNOLGIES AND SYSTEMS FOR WATER MANAGEMENT AND CONDENSATES IN THE SUGAR PRODUCTION

Directory of Open Access Journals (Sweden)

Meilyn González Cortés

2015-01-01

Full Text Available Sugar factories do achieve an efficient use of process water, but this process should be self-sufficient for consumption because these sugar factories have the special characteristic of having as its main raw material, sugar cane, which consists in approximately 70% of water Those condensed recovered will be the first option to recover process water and are aimed to the feeding of boilers. The quantities of the condensate types are dependent of the evaporator’s configuration, also the grade in that show up the vapor extractions. In this paper the fundamental aspects are described as for the use and handling of water in the process of sugar production. Also, important considerations are shown on the treatment systems of residual that are generated in these factories. The evaporation system is shown as the most important area for the handling of water in the process, in it, vegetable vapor takes place and it is used in other technological equipment. A major surplus of steam will be produced in this area if the process is more energetically efficient. It is shown through a balance of water that the process is self-sufficient for water consumption.

Miniature electron bombardment evaporation source: evaporation rate measurement

International Nuclear Information System (INIS)

Nehasil, V.; Masek, K.; Matolin, V.; Moreau, O.

1997-01-01

Miniature electron beam evaporation sources which operate on the principle of vaporization of source material, in the form of a tip, by electron bombardment are produced by several companies specialized in UHV equipment. These sources are used primarily for materials that are normally difficult to deposit due to their high evaporation temperature. They are appropriate for special applications such as heteroepitaxial thin film growth requiring a very low and well controlled deposition rate. A simple and easily applicable method of evaporation rate control is proposed. The method is based on the measurement of ion current produced by electron bombardment of evaporated atoms. The absolute evaporation flux values were measured by means of the Bayard-Alpert ion gauge, which enabled the ion current vs evaporation flux calibration curves to be plotted. (author). 1 tab., 4 figs., 6 refs

Investigation of physical properties and stability of indomethacin-cimetidine and naproxen-cimetidine co-amorphous systems prepared by quench cooling, coprecipitation and ball milling

DEFF Research Database (Denmark)

Lim, Ai Wei; Löbmann, Korbinian; Grohganz, Holger

2016-01-01

the samples. Structural relaxation (i.e. molecular mobility) behaviour was obtained from the Kohlrausch-Williams-Watts (KWW) relationship. KEY FINDINGS: A glass transition temperature (Tg ), on average 20 °C higher than the predicted Tg (calculated from the Fox equation), was observed in all samples....... The structural relaxation was dependent on the preparative methods. At a storage temperature of 40 °C, a comparatively higher molecular mobility was observed in indomethacin-cimetidine samples prepared by ball milling (ln τ(β) = 0.8), while similar molecular mobility was found for the same sample prepared...... by quench cooling (ln τ(β) = 2.4) and co-evaporation (ln τ(β) = 2.5). In contrast, molecular mobility of the naproxen-cimetidine samples followed the order co-evaporation (ln τ(β) = 0.8), quench cooling (ln τ(β) = 1.6) and ball milling (ln τ(β) = 1.8). CONCLUSION: The estimated relaxation times by the DSC...

Uranium milling costs

International Nuclear Information System (INIS)

Coleman, R.B.

1980-01-01

Basic process flowsheets are reviewed for conventional milling of US ores. Capital costs are presented for various mill capacities for one of the basic processes. Operating costs are shown for various mill capacities for all of the basic process flowsheets. The number of mills using, or planning to use, a particular process is reviewed. A summary of the estimated average milling costs for all operating US mills is shown

Evaporators

DEFF Research Database (Denmark)

Knudsen, Hans Jørgen Høgaard

1996-01-01

Type of evaporators. Regulation. Thermal dimensioning. Determination of pressure loss and heat transfer coefficients.......Type of evaporators. Regulation. Thermal dimensioning. Determination of pressure loss and heat transfer coefficients....

Comparison of various milling modes combined to the enzymatic hydrolysis of lignocellulosic biomass for bioenergy production: Glucose yield and energy efficiency

International Nuclear Information System (INIS)

Licari, A.; Monlau, F.; Solhy, A.; Buche, P.; Barakat, A.

2016-01-01

Bagasse is an abundant by-product from sugarcane production that can be used for conversion into biofuels. Nonetheless, the recalcitrant structures of lignocellulosic fibers required a pretreatment prior conversion into biofuels. In this study, four mechanical deconstruction methods were compared in terms of energy demand and energy efficiency at lab scale: BM (ball mill), VBM (vibratory ball mill), CM (centrifugal mill) and JM (jet mill). Results indicate that VBM was more effective compared to BM, JM and CM in enzymatic accessibility and sugars solubilization: VBM-3h > BM-72 h > JM-5000 rpm > CM-0.12 mm. However, preliminary energetic assessment showed that at lab scale, the CM (centrifugal mill) as mechanical fractionation process appears to be the most efficient in terms of energy-efficiency (kg glucose/kWh) compared to BM, VBM and JM. A comparison with literature pretreatments data highlighted that fine and/or ultrafine milling process (BM, VBM, CM) are simpler saccharification technologies, which not required any chemical or water inputs, thus minimizing waste generation and treatment. - Highlights: • VBM (vibro ball milling) was the most effective in decreasing of cellulose crystallinity. • BM (ball milling) was the most effective in increasing surface area. • The highest energy efficiency was obtained with CM (centrifugal milling).

Genetic improvement of sugar cane for bioenergy: the Brazilian experience in network research with RIDESA

Directory of Open Access Journals (Sweden)

Luiz Alexandre Peternelli

2012-01-01

Full Text Available In this paper, it is presented RIDESA’s model for sugar cane breeding to ethanol, and its scientific, technological and human resources training contributions. RIDESA is an inter-university network for the development of sugar cane industry in Brazil, and was formed by a technical cooperation agreement between ten public universities. The model of network management is presented in this study, which involves, among other things, the public-private partnership (Universities-Mills for the development of cultivars. RIDESA has produced 59 cultivars since 1990 and is now responsible for 59% of the total area cultivated with this plant in Brazil. In the last five years, 286 agronomists were trained in breeding programs at universities that comprise RIDESA. In this same period, the network formed 35 professors, 24 doctors and 7 post-docs in researches with this crop. It is also presented a conceptual approach on methods of sugar cane breeding involving families and genome-wide selection.

Flash evaporator

OpenAIRE

1997-01-01

A device and method for flash evaporating a reagent includes an evaporation chamber that houses a dome on which evaporation occurs. The dome is solid and of high thermal conductivity and mass, and may be heated to a temperature sufficient to vaporize a specific reagent. The reagent is supplied from an external source to the dome through a nozzle, and may be supplied as a continuous stream, as a shower, and as discrete drops. A carrier gas may be introduced into the evaporation chamber and cre...

Fumaric acid production using renewable resources from biodiesel and cane sugar production processes.

Science.gov (United States)

Papadaki, Aikaterini; Papapostolou, Harris; Alexandri, Maria; Kopsahelis, Nikolaos; Papanikolaou, Seraphim; de Castro, Aline Machado; Freire, Denise M G; Koutinas, Apostolis A

2018-04-13

The microbial production of fumaric acid by Rhizopus arrhizus NRRL 2582 has been evaluated using soybean cake from biodiesel production processes and very high polarity (VHP) sugar from sugarcane mills. Soybean cake was converted into a nutrient-rich hydrolysate via a two-stage bioprocess involving crude enzyme production via solid state fermentations (SSF) of either Aspergillus oryzae or R. arrhizus cultivated on soybean cake followed by enzymatic hydrolysis of soybean cake. The soybean cake hydrolysate produced using crude enzymes derived via SSF of R. arrhizus was supplemented with VHP sugar and evaluated using different initial free amino nitrogen (FAN) concentrations (100, 200, and 400 mg/L) in fed-batch cultures for fumaric acid production. The highest fumaric acid concentration (27.3 g/L) and yield (0.7 g/g of total consumed sugars) were achieved when the initial FAN concentration was 200 mg/L. The combination of VHP sugar with soybean cake hydrolysate derived from crude enzymes produced by SSF of A. oryzae at 200 mg/L initial FAN concentration led to the production of 40 g/L fumaric acid with a yield of 0.86 g/g of total consumed sugars. The utilization of sugarcane molasses led to low fumaric acid production by R. arrhizus, probably due to the presence of various minerals and phenolic compounds. The promising results achieved through the valorization of VHP sugar and soybean cake suggest that a focused study on molasses pretreatment could lead to enhanced fumaric acid production.

Ultrafiltration of thin stillage from conventional and e-mill dry grind processes.

Science.gov (United States)

Arora, Amit; Dien, Bruce S; Belyea, Ronald L; Wang, Ping; Singh, Vijay; Tumbleson, M E; Rausch, Kent D

2011-05-01

We used ultrafiltration (UF) to evaluate membrane filtration characteristics of thin stillage and determine solids and nutrient compositions of filtered streams. To obtain thin stillage, corn was fermented using laboratory methods. UF experiments were conducted in batch mode under constant temperature and flow rate conditions. Two regenerated cellulose membranes (10 and 100 kDa molecular weight cutoffs) were evaluated with the objective of retaining solids as well as maximizing permeate flux. Optimum pressures for 10 and 100 kDa membranes were 207 and 69 kPa, respectively. Total solids, ash, and neutral detergent fiber contents of input TS streams of dry grind and E-Mill processes were similar; however, fat and protein contents were different (p stillage fractionation had higher mean total solids contents (27.6% to 27.8%) compared to E-Mill (22.2% to 23.4%). Total solids in retentate streams were found similar to those from commercial evaporators used in industry (25% to 35% total solids). Fat contents of retentate streams ranged from 16.3% to 17.5% for the conventional process. A 2% increment in fat concentration was observed in the E-Mill retentate stream. Thin stillage ash content was reduced 60% in retentate streams.

Mechanical alloying and reactive milling in a high energy planetary mill

International Nuclear Information System (INIS)

Jiang Xianjin; Trunov, Mikhaylo A.; Schoenitz, Mirko; Dave, Rajesh N.; Dreizin, Edward L.

2009-01-01

Powder refinement in a planetary mill (Retsch PM 400-MA) is investigated experimentally and analyzed using discrete element modeling (DEM). Refinement is defined as the average size of the individual components in a composite powder. The specific milling dose, defined as the product of charge ratio and milling time, is used as an experimental parameter tracking the progress of the material refinement. This parameter is determined experimentally for milling of boron and titanium powders, for which the time of initiation of a self-sustained reaction is measured under different milling conditions. It is assumed that the reaction becomes self-sustaining when the same powder refinement is achieved. The DEM calculations established that the milling balls primarily roll along the milling container's perimeter. The inverse of the rate of energy dissipation resulting from this rolling motion is used as the DEM analog of the specific milling dose. The results correlate well with experimental observations.

The crystallization of amorphous Fe2MnGe powder prepared by ball milling

International Nuclear Information System (INIS)

Zhang, L.; Brueck, E.; Tegus, O.; Buschow, K.H.J.; Boer, F.R. de

2003-01-01

We synthesized for the first time the intermetallic compound Fe 2 MnGe. To avoid preferential evaporation of volatile components we exploited mechanical alloying. Amorphous Fe 2 MnGe alloy powder was prepared by planetary ball milling elemental starting materials. The amorphous-to-crystalline transition was studied by means of differential scanning calorimetry (DSC) and X-ray diffraction (XRD). A cubic D0 3 phase is formed at low temperature and transforms to a high-temperature hexagonal D0 19 phase. The apparent activation energy was determined by means of the Kissinger method

Bio-refinery system of DME or CH4 production from black liquor gasification in pulp mills

Energy Technology Data Exchange (ETDEWEB)

Raza, M.; Jinyue Yan (Dept. of Chemical Engineering and Technology/Energy Processes, Royal Institute of Technology, Stockholm (Sweden)). e-mail: rnaqvi@kth.se; Froeling, Morgan (Dept. of Chemical and Biological Engineering, Chalmers Univ. of Technology, Goeteborg (Sweden))

2009-07-01

The consumption of fossil fuels is rapidly increasing and there is an urgent need to develop technologies for renewable fuel production not only as alternatives but also as additional fuels. Efficient polygeneration of transportation fuels with heat and electricity is one of the innovative technologies which have potential to replace fossil fuels and mitigate climate change. Two potential technologies of producing dimethyl ether (DME) and methane (CH4) as alternative fuels integrated with black liquor gasification have been studied and compared in this paper. System performance is evaluated based on: (i) Comparison with the reference pulp mill, (ii) Fuel to product efficiency (FTPE) and (iii) Biofuel Production Potential (BPP). The comparison with the reference mill shows that black liquor to biofuel route will add a highly significant new revenue stream to the pulp industry. The results indicate a large potential of DME and CH4 production globally in terms of black liquor availability. BPP and FTPE of CH4 production is higher than DME due to more optimized integration with the pulping process and elimination of evaporation unit in the pulp mill

Top Value Added Chemicals From Biomass. Volume 1 - Results of Screening for Potential Candidates From Sugars and Synthesis Gas

Science.gov (United States)

2004-08-01

UsesIntermediatesBiomass Feedstocks Sugars Glucose Fructose Xylose Arabinose Lactose Sucrose Starch Starch Cellulose Lignin Oil Protein Hemicellulose...these goals, the Program supports the integrated biorefinery, a processing facility that extracts carbohydrates, oils, lignin , and other materials from...biomass, converts them into multiple products including fuels and high value chemicals and materials. Already today, corn wet and dry mills, and

Sugar-Based Ethanol Biorefinery: Ethanol, Succinic Acid and By-Product Production

Energy Technology Data Exchange (ETDEWEB)

Donal F. Day

2009-03-31

The work conducted in this project is an extension of the developments itemized in DE-FG-36-04GO14236. This program is designed to help the development of a biorefinery based around a raw sugar mill, which in Louisiana is an underutilized asset. Some technical questions were answered regarding the addition of a biomass to ethanol facility to existing sugar mills. The focus of this work is on developing technology to produce ethanol and valuable by-products from bagasse. Three major areas are addressed, feedstock storage, potential by-products and the technology for producing ethanol from dilute ammonia pre-treated bagasse. Sugar mills normally store bagasse in a simple pile. During the off season there is a natural degradation of the bagasse, due to the composting action of microorganisms in the pile. This has serious implications if bagasse must be stored to operate a bagasse/biorefinery for a 300+ day operating cycle. Deterioration of the fermentables in bagasse was found to be 6.5% per month, on pile storage. This indicates that long term storage of adequate amounts of bagasse for year-round operation is probably not feasible. Lignin from pretreatment seemed to offer a potential source of valuable by-products. Although a wide range of phenolic compounds were present in the effluent from dilute ammonia pretreatment, the concentrations of each (except for benzoic acid) were too low to consider for extraction. The cellulosic hydrolysis system was modified to produce commercially recoverable quantities of cellobiose, which has a small but growing market in the food process industries. A spin-off of this led to the production of a specific oligosaccharide which appears to have both medical and commercial implications as a fungal growth inhibitor. An alternate use of sugars produced from biomass hydrolysis would be to produce succinic acid as a chemical feedstock for other conversions. An organism was developed which can do this bioconversion, but the economics of

Phytochemical characterization of the threatened specie Fraxinus caroliniana Mill subsp. cubensis (Griseb. Borhidi

Directory of Open Access Journals (Sweden)

Mabelkis Terry Rosabal

2016-04-01

Full Text Available Fraxinus caroliniana Mill subsp. cubensis (Griseb. Borhidi is commonly known as buffalo, represents an endemic subspecies and categorized as critical danger of extinction in Cuba. This work aimed to characterize the phytochemical composition of plants of F. caroliniana in two localities of the Matanzas province. The presence of secondary metabolites in leaf extracts was qualitatively analyzed and reductive and total sugars were quantified. The results indicated the presence of flavonoids, terpenes, steroids, saponins, tannins and anthraquinones in leaves that could be considered for further systematic studies and application in agriculture. The plants from the Ciénaga de Zapata showed contents of reducing sugars and totals higher than those obtained in the plants of Martí. These results provide information for the identification of characters of possible taxonomic and conservation value in this species.   Keywords: anthraquinons, extracts, swamp ash, steroids, tannins, terpens

Economic impacts of implementing the new plants to sugar cane; Impactos economicos da implementacao das novas usinas de cana-de-acucar

Energy Technology Data Exchange (ETDEWEB)

Terciote, Ricardo [Universidade Estadual de Campinas (DE/FEM/UNICAMP), SP (Brazil). Fac. de Engenharia Mecanica. Dept. de Energia

2006-07-01

The sugar industry goes through an important moment: invest and develop to supply future demand, mainly by fuel alcohol (around 70% of new vehicles sales are from flex fuel models - and the majority of these vehicles are supplied by alcohol). Due to this foreseeable increase of alcohol demand, sugar industry has already announced 41 new projects, which will contribute with the milling of 70 million tons of sugar cane by the conclusion of these plants. In this phase of expansion, the alcohol market must be pressured for the demand, managing the supplying of the domestic and external markets. With this scenario and the possibility of sector growth which has an important role in Brazil development, this work evaluates the economic impacts of the new plants implementation investments. (author)

Evaporational losses under different soil moisture regimes and atmospheric evaporativities using tritium

International Nuclear Information System (INIS)

Saxena, P.; Chaudhary, T.N.; Mookerji, P.

1991-01-01

Tritium as tracer was used in a laboratory study to estimate the contribution of moisture from different soil depths towards actual soil water evaporation. Results indicated that for comparable amounts of free water evaporation (5 cm), contribution of moisture from 70-80 cm soil layer towards total soil moisture loss through evaporation increased nearly 1.5 to 3 folds for soils with water table at 90 cm than without water table. Identical initial soil moistures were exposed to different atmospheric evaporativities. Similarly, for a given initial soil moisture status, upward movement of moisture from 70-80 cm soil layer under low evaporativity was nearly 8 to 12 times that of under high evaporativity at 5 cm free water evaporation value. (author). 6 refs., 4 tabs., 2 figs

Saccharification and fermentation of whole barley ground in the Szego mill

Energy Technology Data Exchange (ETDEWEB)

Wayman, M; Parekh, S R; Parekh, R S; Trass, O; Gandolfi, E

1988-11-01

Barley, after steeping in water, was ground with ease and efficiency in the Szego mill, and its starch was liquefied, saccharified and fermented to very high yields of ethanol. The Szego mill consists of vertical rollers with helical grooves which rotate within a fixed cylinder, resulting in very fine grinding and a somewhat flaky product. The steeped barley was ground to a fine paste. This was readily liquefied and saccharified by amylolytic enzymes (dual enzyme process), and the resulting sugars were fermented in 24 h by ordinary bakers' yeast Saccharomyces cerevisiae, resulting in over 450 l ethanol/t of barley. Still shorter time, 12 h, and the same high yield were achieved when liquefied barley starch was simultaneously saccharified by glucoamylase and fermented. Fermentation to ethanol by a glucoamylase-producing yeast S. diastaticus strain 164A (from Labatt Brewing Company) enabled the amount of this enzyme required for saccharification to be reduced to about one-half the normal quantity, but at some cost in slower fermentation and slightly lower ethanol yield.

Heat and mass transfer analogies for evaporation models at high evaporation rate

OpenAIRE

Trontin , P.; Villedieu , P.

2014-01-01

International audience; In the framework of anti and deicing applications, heated liquid films can appear above the ice thickness, or directly above the wall. Then, evaporation plays a major role in the Messinger balance and evaporated mass has to be predicted accurately. Unfortunately, it appears that existing models under-estimate evaporation at high temperature. In this study, different evaporation models at high evaporation rates are studied. The different hypothesis on which these models...

IMPACT OF FURFURAL ON THE SUGAR ANALYSIS OF PRE-HYDROLYSIS LIQUOR OF KRAFT-BASED DISSOLVING PULP PRODUCTION PROCESS USING THE HPAEC TECHNIQUE

Directory of Open Access Journals (Sweden)

Abrar Saeed

2011-03-01

Full Text Available High performance anion-exchange chromatography with pulse ampero-metric detector (HPAEC-PAD is a reliable method to systematically determine the sugar contents in pulp and paper waste streams, including bleaching and extraction liquors. We used the same method to determine the sugar content of industrially produced pre-hydrolysis liquor (PHL from a kraft-based dissolving pulp production process. The analysis showed that the traditional method cannot be applied for sugar analysis, and an improvement on the method was required. In fact, the presence of furfural in the PHL sample was the reason for the required modification. It was noted that the removal of furfural via evaporation could improve the reliability of the HPAEC technique for sugar assessments. If the concentration of furfural was higher than 0.045% (wt. in the PHL, the error introduced in the sugar analysis was profound. Also, the industrially produced PHL contained more furfural than the laboratory produced PHL under the same hydrolysis conditions. Consequently, the concentration of furfural in the PHL should be taken into account for sugar analysis using the HPAEC technique.

Effects of Non Process Elements in the chemical recovery system of paper mills; Effekter av PFG foer integrerade pappersbruk vid indunstning och foerbraenning av bioslam i sodapannan

Energy Technology Data Exchange (ETDEWEB)

Dahlbom, Johan [AaF Process AB, Stockholm (Sweden); Wadsborn, Rickard [STFI-Packforsk AB, Stockholm (Sweden)

2005-09-01

Effluent treatment of pulp and paper mills generates a biological sludge that according to Swedish implementation of EU-directives from 2005 has to be taken care of by incineration or by production of soil for agriculture or ground cover. An alternative way to take care of the sludge is incineration in the recovery boiler. This method is used in two Finish and two Swedish pulp mills with good results. The purpose of this project is to investigate the consequences for integrated pulp and paper mills when the biological sludge is incinerated in the recovery boiler. The biological sludge contents Non Process Elements, NPE, which increase the risks of incrustations in the system and increase the need of make up lime. This study comprises the following NPE: aluminum, silicon, phosphorus, chloride, potassium, manganese, magnesium, iron, copper, barium and calcium. The simulation program WinGEMS 5.0 (Pacific Simulation) was used in the study to predict the levels of NPE in the recovery system of the Kraft mills. Three different pulp and paper mills were selected for the study, Billerud Skaerblacka, ASSI Domaen Froevi and SCA Obbola. The mills are different concerning raw materials, process, degree of own produced pulp and paper products. All three the mills have effluent treatment and use the method of activated sludge that generates a surplus of biological sludge. The results of the study proved that for Skaerblacka mill the method is applicable. For Obbola the prerequisites are somewhat more complicated, the effluent treatment generates considerably higher amount of sludge per ton pulp produced due to the treatment technique and use of waste paper (40 %) for the paper machine. The high input of aluminum with the sludge will give troublesome incrustations of sodium-aluminum-silicate on the heat surfaces in the evaporation plant. To eliminate the aluminum from the system magnesium can be added to the black liquor which will precipitate as the double salt hydrotalcite in

Radiotracer investigation to study residence time distribution in an evaporator system

Energy Technology Data Exchange (ETDEWEB)

Pant, H J; Yelgaonkar, V N; Navada, S V [Isotope Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Determination of mean residence time, residence time distribution and evaluation of flow behavior in industrial process systems is of prime importance in order to control the process and to evaluate the performance of the process systems. This paper describes a case study carried out in an evaporator system in a sugar factory near Pune for determination of the mean residence time and residence time distribution using radiotracer technique. The mean residence time (MRT) was determined to be 4 seconds. The mathematical modelling of residence time distribution (RTD) data indicated the flow behaviour of the system to be a well mixed type. (author). 5 refs., 2 figs., 1 tab.

Evaporator Cleaning Studies

International Nuclear Information System (INIS)

Wilmarth, W.R.

1999-01-01

Operation of the 242-16H High Level Waste Evaporator proves crucial to liquid waste management in the H-Area Tank Farm. Recent operational history of the Evaporator showed significant solid formation in secondary lines and in the evaporator pot. Additional samples remain necessary to ensure material identity in the evaporator pot. Analysis of these future samples will provide actinide partitioning information and dissolution characteristics of the solid material from the pot to ensure safe chemical cleaning

Mixed phase evaporation source

International Nuclear Information System (INIS)

1975-01-01

Apparatus for reducing convection current heat loss in electron beam evaporator is described. A material to be evaporated (evaporant) is placed in the crucible of an electron beam evaporation source along with a porous mass formed of a powdered or finely divided solid to act as an impedance to convection currents. A feed system is employed to replenish the supply of evaporant as it is vaporized

Saccharification of recalcitrant biomass and integration options for lignocellulosic sugars from Catchlight Energy's sugar process (CLE Sugar).

Science.gov (United States)

Gao, Johnway; Anderson, Dwight; Levie, Benjamin

2013-01-28

Woody biomass is one of the most abundant biomass feedstocks, besides agriculture residuals in the United States. The sustainable harvest residuals and thinnings alone are estimated at about 75 million tons/year. These forest residuals and thinnings could produce the equivalent of 5 billion gallons of lignocellulosic ethanol annually. Softwood biomass is the most recalcitrant biomass in pretreatment before an enzymatic hydrolysis. To utilize the most recalcitrant lignocellulosic materials, an efficient, industrially scalable and cost effective pretreatment method is needed. Obtaining a high yield of sugar from recalcitrant biomass generally requires a high severity of pretreatment with aggressive chemistry, followed by extensive conditioning, and large doses of enzymes. Catchlight Energy's Sugar process, CLE Sugar, uses a low intensity, high throughput variation of bisulfite pulping to pretreat recalcitrant biomass, such as softwood forest residuals. By leveraging well-proven bisulfite technology and the rapid progress of enzyme suppliers, CLE Sugar can achieve a high yield of total biomass carbohydrate conversion to monomeric lignocellulosic sugars. For example, 85.8% of biomass carbohydrates are saccharified for un-debarked Loblolly pine chips (softwood), and 94.0% for debarked maple chips (hardwood). Furan compound formation was 1.29% of biomass feedstock for Loblolly pine and 1.10% for maple. At 17% solids hydrolysis of pretreated softwood, an enzyme dose of 0.075 g Sigma enzyme mixture/g dry pretreated (unwashed) biomass was needed to achieve 8.1% total sugar titer in the hydrolysate and an overall prehydrolysate liquor plus enzymatic hydrolysis conversion yield of 76.6%. At a much lower enzyme dosage of 0.044 g CTec2 enzyme product/g dry (unwashed) pretreated softwood, hydrolysis at 17% solids achieved 9.2% total sugar titer in the hydrolysate with an overall sugar yield of 85.0% in the combined prehydrolysate liquor and enzymatic hydrolysate. CLE Sugar has

Monticello Mill Tailings Site, Operable Unit lll, Annual Groundwater Report, May 2015 Through April 2016

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Jason [USDOE Office of Legacy Management (LM), Washington, DC (United States); Smith, Fred [Navarro Research and Engineering, Oak Ridge, TN (United States)

2016-10-01

This report provides the annual analysis of water quality restoration progress, cumulative through April 2016, for Operable Unit (OU) III, surface water and groundwater, of the U.S. Department of Energy (DOE) Office of Legacy Management (LM) Monticello Mill Tailings Site (MMTS). The MMTS is a Comprehensive Environmental Response, Compensation, and Liability Act National Priorities List site located in and near the city of Monticello, San Juan County, Utah. MMTS comprises the 110-acre site of a former uranium- and vanadium-ore-processing mill (mill site) and 1700 acres of surrounding private and municipal property. Milling operations generated 2.5 million cubic yards of waste (tailings) from 1942 to 1960. The tailings were impounded at four locations on the mill site. Inorganic constituents in the tailings drained from the impoundments to contaminate local surface water (Montezuma Creek) and groundwater in the underlying alluvial aquifer. Mill tailings dispersed by wind and water also contaminated properties surrounding and downstream of the mill site. Remedial actions to remove and isolate radiologically contaminated soil, sediment, and debris from the former mill site, Operable Unit I (OU I), and surrounding properties (OU II) were completed in 1999 with the encapsulation of the wastes in an engineered repository located on DOE property 1 mile south of the former mill site. This effectively removed the primary source of groundwater contamination; however, contamination of groundwater and surface water remains within OU III at levels that exceed water quality protection standards. Uranium is the primary contaminant of concern (COC). LM implemented monitored natural attenuation with institutional controls as the OU III remedy in 2004. Because groundwater restoration proceeded more slowly than expected and did not meet performance criteria established in the OU III Record of Decision (June 2004), LM implemented a contingency action in 2009 by an Explanation of

Sugar Sugar – don’t be misled / laat je niet misleiden

NARCIS (Netherlands)

Toebes, Brigit

2017-01-01

NRC Handelsblad’s Saturday 25 November issue contains an entry of eleven pages entirely devoted to sugar. It discusses a broad range of topics related to sugar, including the role of sugar throughout the centuries, sugar consumption in the Netherlands, the amount of sugar in bread, and sugar

Blood sugar test

Science.gov (United States)

... sugar; Blood sugar level; Fasting blood sugar; Glucose test; Diabetic screening - blood sugar test; Diabetes - blood sugar test ... The test may be done in the following ways: After you have not eaten anything for at least 8 ...

Uranium-mill appraisal program

International Nuclear Information System (INIS)

Everett, R.J.; Cain, C.L.

1982-08-01

The results of special team appraisals at NRC-licensed uranium mills in the period May to November 1981 are reported. Since the Three Mile Island accident, NRC management has instituted a program of special team appraisals of radiation protection programs at certain NRC-licensed facilities. These appraisals were designed to identify weaknesses and strengths in NRC-licensed programs, including those areas not covered by explicit regulatory requirements. The regulatory requirements related to occupational radiation protection and environmental monitoring at uranium mills have been extensively upgraded in the past few years. In addition, there was some NRC staff concern with respect to the effectiveness of NRC licensing and inspection programs. In response to this concern and to changes in mill requirements, the NRC staff recommended that team appraisals be conducted at mills to determine the adequacy of mill programs, the effectiveness of the new requirements, and mill management implementation of programs and requirements. This report describes the appraisal scope and methodology as well as summary findings and conclusions. Significant weaknesses identified during the mill appraisals are discussed as well as recommendations for improvements in uranium mill programs and mill licensing and inspection

Determination of amino acids in industrial effluents contaminated soil

International Nuclear Information System (INIS)

Mahar, M.T.; Khuhawar, M.Y.

2014-01-01

38 samples of soil for 19 locations partially irrigated on the effluents of sugar mill and oil andghee mill, bottom sediments of evaporation ponds of sugar and fertilizer industries were collected and analyzed for amino acids after acid digestion by gas chromatography using pre column derivatization with trifluroacetyleacetone and ethyl chloroformate. The results obtained were compared with the soil samples irrigated with fresh water. The soil samples were also analyzed for pH, total nitrogen contents and organic carbon. Nine essential (leucine (Leu), threonine (Thr), lysine (Lys), L-phenylalanine (Phe), tryptophan (Trp), histadine (His), L-valine (Val), methionine (Met) and isoleucine Ile) and ten non-essential ( alanine (Ala), cysteine (Cys), asparagine (Asn), glutamic acid (Glu), serine (Ser), glycine (Gly), proline (Pro), Glutamine (Gln), aspartic acid (Asp), tyrosine (Tyr)) amino acids were analyzed 13-15 amino acids were identified and determined quantitatively from soil samples. Amino acids Met, Asn, Gln and Trp were observed absent from all the samples. The variation in the amino acids contents in soil with the industrial effluents added and total nitrogen and organic carbon is discussed. (author)

76 FR 62339 - Domestic Sugar Program-2011-Crop Cane Sugar and Beet Sugar Marketing Allotments and Company...

Science.gov (United States)

2011-10-07

... DEPARTMENT OF AGRICULTURE Commodity Credit Corporation Domestic Sugar Program--2011-Crop Cane Sugar and Beet Sugar Marketing Allotments and Company Allocations AGENCY: Commodity Credit Corporation... the fiscal year (FY) 2012 State sugar marketing allotments and company allocations to sugarcane and...

Pengaruh Penambahan Natrium Metabisulfit dan Suhu Pemasakan dengan Menggunakan Teknologi Vakum terhadap Kualitas Gula Merah Tebu

OpenAIRE

Maya Maharani, Dewi; Yulianingsih, Rini; Rosalia Dewi, Shinta; Sugiarto, Yusron; Wahyu Indriani, Dina

2015-01-01

Brown sugar as sucrose is derived from evaporated sugar cane molasses. Evaporation is the foodstuffs’ process which is commonly used during the manufacture of sugar cane. This process evaporates the sugar cane molasses to produce concentrate. This research was aimed to assess the influence of sodium metabisulphite against physical and chemical properties of sugar cane using vacuum evaporator. In other hand, this reserach examined the influence of temperature on vacuum evaporator for chemical ...

Pengaruh Penambahan Natrium Metabisulfit dan Suhu Pemasakan dengan Menggunakan Teknologi Vakum terhadap Kualitas Gula Merah Tebu

OpenAIRE

Maya Maharani, Dewi; Yulianingsih, Rini; Rosalia Dewi, Shinta; Sugiarto, Yusron; Wahyu Indriani, Dina

2014-01-01

Brown sugar as sucrose is derived from evaporated sugar cane molasses. Evaporation is the foodstuffs' process which is commonly used during the manufacture of sugar cane. This process evaporates the sugar cane molasses to produce concentrate. This research was aimed to assess the influence of sodium metabisulphite against physical and chemical properties of sugar cane using vacuum evaporator. In other hand, this reserach examined the influence of temperature on vacuum evaporator for chemical ...

Development-specific responses to drought stress in Aleppo pine (Pinus halepensis Mill.) seedlings.

Science.gov (United States)

Alexou, Maria

2013-10-01

Aleppo pine (Pinus halepensis Mill.) is a pioneer species, highly competitive due to exceptional resistance to drought. To investigate the stress resistance in the first and second year of development, a steady-state drought experiment was implemented. Photosynthesis (A(net)), stomatal conductance and transpiration (E) were measured on three different sampling dates together with phloem soluble sugars, amino acids and non-structural proteins. Needle ascorbic acid (AsA) and reactive oxygen species were measured to evaluate the seedlings' drought stress condition in the final sampling. Drought impaired A(net) and E by 35 and 31%, respectively, and increased AsA levels up to 10-fold, without significant impact on the phloem metabolites. Phloem sugars related to temperature fluctuations rather than soil moisture and did not relate closely to A(net) levels. Sugars and proteins decreased between the second and third sampling date by 56 and 61%, respectively, and the ratio of sugars to amino acids decreased between the first and third sampling by 81%, while A(net) and water-use efficiency (A(net)/E) decreased only in the older seedlings. Although gas exchange was higher in the older seedlings, ascorbic acid and phloem metabolites were higher in the younger seedlings. It was concluded that the drought stress responses depended significantly on developmental stage, and research on the physiology of Aleppo pine regeneration should focus more on temperature conditions and the duration of drought than its severity.

Historic mills and mill tailings as potential sources of contamination in and near the Humboldt River basin, northern Nevada. Chapter D.

Science.gov (United States)

Nash, J. Thomas; Stillings, Lisa L.

2003-01-01

Reconnaissance field studies of 40 mining districts in and near the Humboldt River basin have identified 83 mills and associated tailings impoundments and several other kinds of mineral-processing facilities (smelters, mercury retorts, heap-leach pads) related to historic mining. The majority of the mills and tailings sites are not recorded in the literature. All tailings impoundments show evidence of substantial amounts of erosion. At least 11 tailings dams were breached by flood waters, carrying fluvial tailings 1 to 15 km down canyons and across alluvial fans. Most of the tailings sites are dry most of the year, but some are near streams. Tailings that are wet for part of the year do not appear to be reacting significantly with those waters because physical factors such as clay layers and hard-pan cement appear to limit permeability and release of metals to surface waters. The major impact of mill tailings on surface- water quality may be brief flushes of runoff during storm events that carry acid and metals released from soluble mineral crusts. Small ephemeral ponds and puddles that tend to collect in trenches and low areas on tailings impoundments tend to be acidic and extremely enriched in metals, in part through cycles of evaporation. Ponded water that is rich in salts and metals could be acutely toxic to unsuspecting animals. Rare extreme storms have the potential to cause catastrophic failure of tailings impoundments, carry away metals in stormwaters, and transport tailings as debris flows for 1 to 15 km. In most situations these stormwaters and transported tailings could impact wildlife but probably would impact few or no people or domes-tic water wells. Because all identified historic tailings sites are several kilometers or more from the Humboldt River and major tributaries, tailings probably have no measurable impact on water quality in the main stem of the Humboldt River.

Forest evaporation models: Relationships between stand growth and evaporation

CSIR Research Space (South Africa)

Le Maitre, David C

1997-06-01

Full Text Available The relationships between forest stand structure, growth and evaporation were analysed to determine whether forest evaporation can be estimated from stand growth data. This approach permits rapid assessment of the potential impacts of afforestation...

Evaporative cooling: Effective latent heat of evaporation in relation to evaporation distance from the skin

NARCIS (Netherlands)

Havenith, G.; Bröde, P.; Hartog, E.A. den; Kuklane, K.; Holmer, I.; Rossi, R.M.; Richards, M.; Farnworth, B.; Wang, X.

2013-01-01

Calculation of evaporative heat loss is essential to heat balance calculations. Despite recognition that the value for latent heat of evaporation, used in these calculations, may not always reflect the real cooling benefit to the body, only limited quantitative data on this is available, which has

Moisture content analysis of covered uranium mill tailings

International Nuclear Information System (INIS)

Mayer, D.W.; Beedlow, P.A.; Cadwell, L.L.

1981-12-01

The use of vegetation and rock covers to stabilize uranium mill tailings cover systems is being investigated by Pacific Northwest Laboratory. A modeling study of moisture movement through the tailings and cover layers was initiated to determine the effect of the stabilizing techniques. The cover system was simulated under climatic conditions occurring at Grand Junction, Colorado. The cover consisted of a layer of wet clay/gravel mix followed by a capillary barrier of washed rock and a surface layer of fill soil. Vegetation and rock were used to stabilize the surface layer. The simulation yielded moisture content and moisture storage values for the tailings and cover system along with information about moisture losses due to evaporation, transpiration, and drainage. The study demonstrates that different surface stabilization treatments lead to different degrees of moisture retention in the covered tailings pile. The evapotranspiration from vegetation can result in a relatively stable moisture content. Rock covers, however, may cause drainage to occur because they reduce evaporation and lead to a subsequent increase in moisture content. It is important to consider these effects when designing a surface stabilization treatment. Drainage may contribute to a groundwater pollution problem. A surface treatment that allows the cover system to dry out can increase the risk of atmospheric contamination through elevated radon emission rates

Introducing ultrasonic falling film evaporator for moderate temperature evaporation enhancement.

Science.gov (United States)

Dehbani, Maryam; Rahimi, Masoud

2018-04-01

In the present study, Ultrasonic Falling Film (USFF), as a novel technique has been proposed to increase the evaporation rate of moderate temperature liquid film. It is a proper method for some applications which cannot be performed at high temperature, such as foodstuff industry, due to their sensitivity to high temperatures. Evaporation rate of sodium chloride solution from an USFF on an inclined flat plate compared to that for Falling Film without ultrasonic irradiation (FF) at various temperatures was investigated. The results revealed that produced cavitation bubbles have different effects on evaporation rate at different temperatures. At lower temperatures, size fluctuation and collapse of bubbles and in consequence induced physical effects of cavitation bubbles resulted in more turbulency and evaporation rate enhancement. At higher temperatures, the behavior was different. Numerous created bubbles joined together and cover the plate surface, so not only decreased the ultrasound vibrations but also reduced the evaporation rate in comparison with FF. The highest evaporation rate enhancement of 353% was obtained at 40 °C at the lowest Reynolds number of 250. In addition, the results reveal that at temperature of 40 °C, USFF has the highest efficiency compared to FF. Copyright © 2017 Elsevier B.V. All rights reserved.

Integration of micro milling highspeed spindle on a microEDM-milling machine set-up

DEFF Research Database (Denmark)

De Grave, Arnaud; Hansen, Hans Nørgaard; Andolfatto, Loic

2009-01-01

In order to cope with repositioning errors and to combine the fast removal rate of micro milling with the precision and small feature size achievable with micro EDM milling, a hybrid micro-milling and micro-EDM milling centre was built and tested. The aim was to build an affordable set-up, easy...... by micro milling. Examples of test parts are shown and used as an experimental validation....

Uranium Mill Tailings Management

International Nuclear Information System (INIS)

Nelson, J.D.

1982-01-01

This book presents the papers given at the Fifth Symposium on Uranium Mill Tailings Management. Advances made with regard to uranium mill tailings management, environmental effects, regulations, and reclamation are reviewed. Topics considered include tailings management and design (e.g., the Uranium Mill Tailings Remedial Action Project, environmental standards for uranium mill tailings disposal), surface stabilization (e.g., the long-term stability of tailings, long-term rock durability), radiological aspects (e.g. the radioactive composition of airborne particulates), contaminant migration (e.g., chemical transport beneath a uranium mill tailings pile, the interaction of acidic leachate with soils), radon control and covers (e.g., radon emanation characteristics, designing surface covers for inactive uranium mill tailings), and seepage and liners (e.g., hydrologic observations, liner requirements)

Catalytic pyrolysis of olive mill wastewater sludge

Science.gov (United States)

Abdellaoui, Hamza

From 2008 to 2013, an average of 2,821.4 kilotons/year of olive oil were produced around the world. The waste product of the olive mill industry consists of solid residue (pomace) and wastewater (OMW). Annually, around 30 million m3 of OMW are produced in the Mediterranean area, 700,000 m3 year?1 in Tunisia alone. OMW is an aqueous effluent characterized by an offensive smell and high organic matter content, including high molecular weight phenolic compounds and long-chain fatty acids. These compounds are highly toxic to micro-organisms and plants, which makes the OMW a serious threat to the environment if not managed properly. The OMW is disposed of in open air evaporation ponds. After evaporation of most of the water, OMWS is left in the bottom of the ponds. In this thesis, the effort has been made to evaluate the catalytic pyrolysis process as a technology to valorize the OMWS. The first section of this research showed that 41.12 wt. % of the OMWS is mostly lipids, which are a good source of energy. The second section proved that catalytic pyrolysis of the OMWS over red mud and HZSM-5 can produce green diesel, and 450 °C is the optimal reaction temperature to maximize the organic yields. The last section revealed that the HSF was behind the good fuel-like properties of the OMWS catalytic oils, whereas the SR hindered the bio-oil yields and quality.

Preliminary Test of Upgraded Conventional Milling Machine into PC Based CNC Milling Machine

International Nuclear Information System (INIS)

Abdul Hafid

2008-01-01

CNC (Computerized Numerical Control) milling machine yields a challenge to make an innovation in the field of machining. With an action job is machining quality equivalent to CNC milling machine, the conventional milling machine ability was improved to be based on PC CNC milling machine. Mechanically and instrumentally change. As a control replacing was conducted by servo drive and proximity were used. Computer programme was constructed to give instruction into milling machine. The program structure of consists GUI model and ladder diagram. Program was put on programming systems called RTX software. The result of up-grade is computer programming and CNC instruction job. The result was beginning step and it will be continued in next time. With upgrading ability milling machine becomes user can be done safe and optimal from accident risk. By improving performance of milling machine, the user will be more working optimal and safely against accident risk. (author)

The potential of biogas and electric power production from subproducts in the sugar and alcohol industries by the application of anaerobic digestion

Energy Technology Data Exchange (ETDEWEB)

Haandel, A. van; Cavalcanti, P.F.F. [Univ. of Campina Grande, Campina Grande, PB (Brazil)

2007-07-01

Since the seventies Brazil maintains a large production program of alcohol from sugar cane. However, the conventional production process is not very efficient: only 40% of the chemical energy of the cane plant are converted into alcohol. On the other hand large amounts of residues are generated, which in many cases have an adverse impact on the environment. In this paper it is shown that what is perceived as a residue, is in fact a subproduct that can be transformed into useful products that can be used in the industrial or agricultural activities of distilleries and sugar mills or be commercialized, thus increasing the profitability of the companies and reducing the environmental impact of these industries. The most important subproducts are bagasse (the solid phase of the cane plant) and stillage (the waste water resulting from the distillation operation). One possibility for application of bagasse is combustion for electric energy generation, which has a potential of 1 MWh per m{sup 3} produced alcohol. By applying anaerobic digestion to stillage, it is possible to generate methane which can be used for electric power generation in explosion motors with a potential of 0,5 MWh per m{sup 3} produced alcohol. Thus there is a production potential of 1,5 MWh per m{sup 3} produced alcohol from the subproducts generated at alcohol distilleries. These operations are already installed at full scale at some industries in Brazil and hold the promise not only to increase substantially the output of useful products, but also have the potential to reduce the environmental impact and can increase the profitability of the entreprises. At lab scale it was demonstrated that there are perspectives of an even larger increase of electric power production if anaerobic digestion of bagasse is applied. The application of Microbial Fuel Cells (MFCs) is a promising development for the near future to increase the useful energy output even further. The production potential of electric

Spectroscopy analysis of phenolic and sugar patterns in a food grade chestnut tannin.

Science.gov (United States)

Ricci, A; Lagel, M-C; Parpinello, G P; Pizzi, A; Kilmartin, P A; Versari, A

2016-07-15

Tannin of chestnut (Castanea sativa Mill.) wood, commonly used in winemaking was characterised with a spectroscopy qualitative approach that revealed its phenolic composition: several vibrational diagnostic bands assigned using the Attenuated Total Reflectance-Infrared Spectroscopy, and fragmentation patterns obtained using the Laser-Desorption-Ionization Time-of-Flight technique evidenced polygalloylglucose, e.g. castalagin/vescalagin-like structures as the most representative molecules, together with sugar moieties. The implication of these findings on winemaking application and the potential influence of the chemical structure on the sensory properties of wine are discussed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Vacuum evaporation of pure metals

OpenAIRE

Safarian, Jafar; Engh, Thorvald Abel

2013-01-01

Theories on the evaporation of pure substances are reviewed and applied to study vacuum evaporation of pure metals. It is shown that there is good agreement between different theories for weak evaporation, whereas there are differences under intensive evaporation conditions. For weak evaporation, the evaporation coefficient in Hertz-Knudsen equation is 1.66. Vapor velocity as a function of the pressure is calculated applying several theories. If a condensing surface is less than one collision...

Evaporation in hydrology and meteorology

OpenAIRE

Brandsma, T.

1990-01-01

In this paper the role of evaporation in hydrology and meteorology is discussed, with the emphasis on hydrology. The basic theory of evaporation is given and methods to determine evaporation are presented. Some applications of evaporation studies in literature are given in order to illustrate the theory. Further, special conditions in evaporation are considered, followed by a fotmulation of the difficulties in determining evaporation, The last part of the paper gives a short discussion about ...

Impacts of Sugar Import Policy on Sugar Production in Indonesia

OpenAIRE

Suryantoro, Agustinus; Susilo, Albertus Magnus; Supriyono, Supriyono

2013-01-01

Production of sugar unful lled consumption of Indonesia society. The lack of consumption and productionhave ful lled by import. Assumption national consumption 2,7 million ton, Indonesia will import sugar in 2013predicted about 300.000 ton (Tempo.co, August, 21, 2012).The aims in general of this research are to understand the impact of sugar import policy on sugar production.Especially (1) to understand the factors that in uence sugar import price, (2) to understand impact of sugarimport pric...

Effects of Dry-Milling and Wet-Milling on Chemical, Physical and Gelatinization Properties of Rice Flour

Directory of Open Access Journals (Sweden)

Jitranut Leewatchararongjaroen

2016-09-01

Full Text Available Rice flour from nine varieties, subjected to dry- and wet-milling processes, was determined for its physical and chemical properties. The results revealed that milling method had an effect on properties of flour. Wet-milling process resulted in flour with significantly lower protein and ash contents and higher carbohydrate content. Wet-milled flour also tended to have lower lipid content and higher amylose content. In addition, wet-milled rice flour contained granules with smaller average size compared to dry-milled samples. Swelling power at 90 °C of wet-milled samples was higher while solubility was significantly lower than those of dry-milled flour. Dry milling process caused the destruction of the crystalline structure and yielded flour with lower crystallinity compared to wet-milling process, which resulted in significantly lower gelatinization enthalpy.

The ultrasound-assisted sugar extraction from sugar beet cossettes

International Nuclear Information System (INIS)

Stasiak, D.M.

2005-01-01

The aim of this work was to study the ultrasound-assisted water extraction of sugar from sugar beet cossettes. The ultrasound bath device (25 kHz, 200 W) was used. The sonication accelerated sugar diffusion at both temperatures 18 deg C and 77.6 deg C and gave the higher level of dry matter content SS (4-6 percent) and sugar content CK (7-22 percent) in juice. The SS and CK depended on time of exposition, time and temperature of extraction. In particular, the effects of 5 min ultrasound-assisted extraction were equal to 20 min extraction in traditional conditions. The shorter time, lower temperature, higher efficiency and purity of juice could be the effects of sugar extraction with ultrasound. The change of thickness of diffusion membrane, microflows in tissue as well as it's environment caused by ultrasound was the reason of acceleration of sugar extraction

On the link between potential evaporation and regional evaporation from a CBL perspective

Science.gov (United States)

Lhomme, J. P.; Guilioni, L.

2010-07-01

The relationship between potential evaporation and actual evaporation was first examined by Bouchet (Proc Berkeley Calif Symp IAHS Publ, 62:134-142, 1963) who considered potential evaporation as the consequence of regional evaporation due to atmospheric feedbacks. Using a heuristic approach, he derived a complementary relationship which, despite no real theoretical background, has proven to be very useful in interpreting many experimental data under various climatic conditions. Here, the relationship between actual and potential evaporation is reinterpreted in the context of the development of the convective boundary layer (CBL): first, with a closed-box approach, where the CBL has an impermeable lid; and then with an open system, where air is exchanged between the CBL and its external environment. By applying steady forcing to these systems, it is shown that an equilibrium state is reached, where potential evaporation has a specific equilibrium formulation as a function of two parameters: one representing large-scale advection and the other the feedback effect of regional evaporation on potential evaporation, i.e. a kind of “medium-scale advection”. It is also shown that the original form of Bouchet’s complementary relationship is not verified in the equilibrium state. This analysis leads us to propose a new and more rational approach of the relationship between potential and actual evaporation through the effective surface resistance of the region.

Energy management in multi stage evaporator through a steady and dynamic state analysis

Energy Technology Data Exchange (ETDEWEB)

Verma, Om Prakash; Manik, Gaurav; Mohammed, Toufiq Haji [Indian Institute of Technology Roorkee, Roorkee (India)

2017-10-15

Increasing energy demand, high cost of energy and global warming issues across the globe require energy intensive industries, such as paper mills to improve energy efficiency. Multi-stage evaporators used to concentrate the black liquor in such mills form its most energy consuming unit and require a strong understanding of steady and unsteady state behavior to ensure energy savings. The modeling of nonlinear heptads’ effect system yielded a set of complex nonlinear algebraic and differential equations that are analyzed using Interior-point method and state space representation. Dynamic response of product concentration and system vapor temperatures along with system stability and controllability have been explored by disturbing the flow rate, concentration and temperature of feed, and fresh steam flow rate. Simulations predict that steam flow rate, feed flow rate and its concentration invariably are major controlling factors (in decreasing order) of vapor temperature and product concentration. The interactive behavior between different effects translates into slower responses of the effects with increasing separation from disturbance source. This steady state and transient study opens many new explanations to this relatively less explored area and helps to propose and implement industrial PID controllers to reduce steam consumption and control product quality.

Investigation of the milling capabilities of the F10 Fine Grind mill using Box-Behnken designs.

Science.gov (United States)

Tan, Bernice Mei Jin; Tay, Justin Yong Soon; Wong, Poh Mun; Chan, Lai Wah; Heng, Paul Wan Sia

2015-01-01

Size reduction or milling of the active is often the first processing step in the design of a dosage form. The ability of a mill to convert coarse crystals into the target size and size distribution efficiently is highly desirable as the quality of the final pharmaceutical product after processing is often still dependent on the dimensional attributes of its component constituents. The F10 Fine Grind mill is a mechanical impact mill designed to produce unimodal mid-size particles by utilizing a single-pass two-stage size reduction process for fine grinding of raw materials needed in secondary processing. Box-Behnken designs were used to investigate the effects of various mill variables (impeller, blower and feeder speeds and screen aperture size) on the milling of coarse crystals. Response variables included the particle size parameters (D10, D50 and D90), span and milling rate. Milled particles in the size range of 5-200 μm, with D50 ranging from 15 to 60 μm, were produced. The impeller and feeder speeds were the most critical factors influencing the particle size and milling rate, respectively. Size distributions of milled particles were better described by their goodness-of-fit to a log-normal distribution (i.e. unimodality) rather than span. Milled particles with symmetrical unimodal distributions were obtained when the screen aperture size was close to the median diameter of coarse particles employed. The capacity for high throughput milling of particles to a mid-size range, which is intermediate between conventional mechanical impact mills and air jet mills, was demonstrated in the F10 mill. Prediction models from the Box-Behnken designs will aid in providing a better guide to the milling process and milled product characteristics. Copyright © 2014 Elsevier B.V. All rights reserved.

EVAPORATION FORM OF ICE CRYSTALS IN SUBSATURATED AIR AND THEIR EVAPORATION MECHANISM

OpenAIRE

ゴンダ, タケヒコ; セイ, タダノリ; Takehiko, GONDA; Tadanori, SEI

1987-01-01

The evaporation form and the evaporation mechanism of dendritic ice crystals grown in air of 1.0×(10)^5 Pa and at water saturation and polyhedral ice crystals grown in air of 4.0×10 Pa and at relatively low supersaturation are studied. In the case of dendritic ice crystals, the evaporation preferentially occurs in the convex parts of the crystal surfaces and in minute secondary branches. On the other hand, in the case of polyhedral ice crystals, the evaporation preferentially occurs in the pa...

Sap-Sugar Content of Grafted Sugar Maple Trees

Science.gov (United States)

Maurice E. Jr. Demeritt; Maurice E. Jr. Demeritt

1985-01-01

In March and April 1983, 289 and 196 young grafted sugar maple trees were tapped and evaluated for sap-sugar content. In April, sap was collected from taps both above and below the graft union. Diameter of all tapped trees at 18 inches above the ground was measured. Analysis of the data revealed that: (1) trees selected for high sugar yield cannot be reproduced by...

Natural radionuclides as dirt tracers in sugar cane consignments

International Nuclear Information System (INIS)

Bacchi, M.A.; Fernandes, E.A.N.

1998-01-01

Soil is usually carried out to the mills, as an impurity in sugar cane, leading to economic drawbacks for the industry. The quantification of this dirt is important to identify its causes and for routine quality control. Several methods have been used for this purpose, however, no single one has been pointed out as an industrial standard. The use of a γ-ray emitting radionuclide of natural occurence was investigated and, after several soil and cane radioactivity analyses, 212 Pb was chosen as the best tracer. Calibration curves developed with the addition of soil in clean cane, from 0 to 10% (dry mass), demonstrated the linearity of the method. Analyses of eleven samples taken from consignments showed that the procedure was consistent and reliable when compared to the traditional ash method. (author)

Einstein-Yang-Mills from pure Yang-Mills amplitudes

Energy Technology Data Exchange (ETDEWEB)

Nandan, Dhritiman; Plefka, Jan [Institut für Physik and IRIS Adlershof, Humboldt-Universität zu Berlin,Zum Großen Windkanal 6, D-12489 Berlin (Germany); Schlotterer, Oliver [Max-Planck-Institut für Gravitationsphysik, Albert-Einstein-Institut,Am Mühlenberg 1, D-14476 Potsdam (Germany); Wen, Congkao [I.N.F.N. Sezione di Roma Tor Vergata,Via della Ricerca Scientifica, 00133 Roma (Italy)

2016-10-14

We present new relations for scattering amplitudes of color ordered gluons and gravitons in Einstein-Yang-Mills theory. Tree-level amplitudes of arbitrary multiplicities and polarizations involving up to three gravitons and up to two color traces are reduced to partial amplitudes of pure Yang-Mills theory. In fact, the double-trace identities apply to Einstein-Yang-Mills extended by a dilaton and a B-field. Our results generalize recent work of Stieberger and Taylor for the single graviton case with a single color trace. As the derivation is made in the dimension-agnostic Cachazo-He-Yuan formalism, our results are valid for external bosons in any number of spacetime dimensions. Moreover, they generalize to the superamplitudes in theories with 16 supercharges.

Evaporation and Climate Change

NARCIS (Netherlands)

Brandsma, T.

1993-01-01

In this article the influence of climate change on evaporation is discussed. The emphasis is on open water evaporation. Three methods for calculating evaporation are compared considering only changes in temperature and factors directly dependent on temperature. The Penman-method is used to

Convection-enhanced water evaporation

OpenAIRE

B. M. Weon; J. H. Je; C. Poulard

2011-01-01

Water vapor is lighter than air; this can enhance water evaporation by triggering vapor convection but there is little evidence. We directly visualize evaporation of nanoliter (2 to 700 nL) water droplets resting on silicon wafer in calm air using a high-resolution dual X-ray imaging method. Temporal evolutions of contact radius and contact angle reveal that evaporation rate linearly changes with surface area, indicating convective (instead of diffusive) evaporation in nanoliter water droplet...

7 CFR 868.310 - Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice...

Science.gov (United States)

2010-01-01

... Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice. (See also Â... Milled Rice Principles Governing Application of Standards § 868.310 Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice...

Comparative technoeconomic analysis of a softwood ethanol process featuring posthydrolysis sugars concentration operations and continuous fermentation with cell recycle.

Science.gov (United States)

Schneiderman, Steven J; Gurram, Raghu N; Menkhaus, Todd J; Gilcrease, Patrick C

2015-01-01

Economical production of second generation ethanol from Ponderosa pine is of interest due to widespread mountain pine beetle infestation in the western United States and Canada. The conversion process is limited by low glucose and high inhibitor concentrations resulting from conventional low-solids dilute acid pretreatment and enzymatic hydrolysis. Inhibited fermentations require larger fermentors (due to reduced volumetric productivity) and low sugars lead to low ethanol titers, increasing distillation costs. In this work, multiple effect evaporation (MEE) and nanofiltration (NF) were evaluated to concentrate the hydrolysate from 30 g/l to 100, 150, or 200 g/l glucose. To ferment this high gravity, inhibitor containing stream, traditional batch fermentation was compared with continuous stirred tank fermentation (CSTF) and continuous fermentation with cell recycle (CSTF-CR). Equivalent annual operating cost (EAOC = amortized capital + yearly operating expenses) was used to compare these potential improvements for a local-scale 5 MGY ethanol production facility. Hydrolysate concentration via evaporation increased EAOC over the base process due to the capital and energy intensive nature of evaporating a very dilute sugar stream; however, concentration via NF decreased EAOC for several of the cases (by 2 to 15%). NF concentration to 100 g/l glucose with a CSTF-CR was the most economical option, reducing EAOC by $0.15 per gallon ethanol produced. Sensitivity analyses on NF options showed that EAOC improvement over the base case could still be realized for even higher solids removal requirements (up to two times higher centrifuge requirement for the best case) or decreased NF performance. © 2015 American Institute of Chemical Engineers.

75 FR 71463 - Woodland Mills Corporation Mill Spring, NC; Notice of Revised Determination on Reconsideration

Science.gov (United States)

2010-11-23

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-73,695] Woodland Mills Corporation Mill Spring, NC; Notice of Revised Determination on Reconsideration By application dated July 22... regarding the eligibility of workers and former workers of Woodland Mills Corporation, Mill Spring, North...

Sugar beet breeding

Science.gov (United States)

Sugar beet is a recent crop developed solely for extraction of the sweetener sucrose. Breeding and improvement of Beta vulgaris for sugar has a rich historical record. Sugar beet originated from fodder beet in the 1800s, and selection has increased sugar content from 4 to 6% then to over 18% today. ...

Increase The Sugar Concentration of The Solution Sugar by Reverse Osmotic Membrane

Science.gov (United States)

Redjeki, S.; Hapsari, N.; Iriani

2018-01-01

Sugar is one of the basic needs of people and food and drink industry. As technology advances and the demand for efficient usage of sugar rises, crystal sugar is seen as less advantageous than liquid sugar. If sugar is always dissolved in water before use, then it will be more efficient and practical for consumers to use sugar in liquid form than in crystal form. Other than that, liquid sugar is also attractive to consumers because it is economical, hygienic, instantly soluble in hot and cold water, fresher and longer-lasting, able to thicken and enrich the texture of foods and drinks, and functions as sweetener, syrup, and flavor enhancer. Liquid sugar is also more beneficial for sugar producers because of simpler production process, cheaper production cost, and similar yield with no extra cost. In sugar production, separation process is found in most of its stages and therefore the use of membrane technology for separating solute and water content has a good potential. In this research, water content reduction of sugar solution was done in order to increase the sugar concentration of the solution. The parameters of this research were 4%, 5%, and 6% starting concentration of sugar solution; 20, 40, and 60 minutes of process time; and 85 and 60 PSI ΔP. The best result was acquired on 4% starting concentration, 60 PSI ΔP, and 60 minutes process time.

Evaporation in hydrology and meteorology

NARCIS (Netherlands)

Brandsma, T.

1990-01-01

In this paper the role of evaporation in hydrology and meteorology is discussed, with the emphasis on hydrology. The basic theory of evaporation is given and methods to determine evaporation are presented. Some applications of evaporation studies in literature are given in order to illustrate the

Isolation, Identification, and Biological Evaluation of Phenolic Compounds from a Traditional North American Confectionery, Maple Sugar.

Science.gov (United States)

Liu, Yongqiang; Rose, Kenneth N; DaSilva, Nicholas A; Johnson, Shelby L; Seeram, Navindra P

2017-05-31

Maple sap, collected from the sugar maple (Acer saccharum) tree, is boiled to produce the popular plant-derived sweetener, maple syrup, which can then be further evaporated to yield a traditional North American confectionery, maple sugar. Although maple sap and maple syrup have been previously studied, the phytochemical constituents of maple sugar are unknown. Herein, 30 phenolic compounds, 1-30, primarily lignans, were isolated and identified (by HRESIMS and NMR) from maple sugar. The isolates included the phenylpropanoid-based lignan tetramers (erythro,erythro)-4″,4‴-dihydroxy-3,3',3″,3‴,5,5'-hexamethoxy-7,9';7',9-diepoxy-4,8″;4',8‴-bisoxy-8,8'-dineolignan-7″,7‴,9″,9‴-tetraol, 29, and (threo,erythro)-4″,4‴-dihydroxy-3,3',3″,3‴,5,5'-hexamethoxy-7,9';7',9-diepoxy-4,8″;4',8‴-bisoxy-8,8'-dineolignan-7″,7‴,9″,9‴-tetraol, 30, neither of which have been identified from maple sap or maple syrup before. Twenty of the isolates (selected on the basis of sample quantity available) were evaluated for their potential biological effects against lipopolysaccharide-induced inflammation in BV-2 microglia in vitro and juglone-induced oxidative stress in Caenorhabditis elegans in vivo. The current study increases scientific knowledge of possible bioactive compounds present in maple-derived foods including maple sugar.

Evaluation of End Mill Coatings

Energy Technology Data Exchange (ETDEWEB)

L. J. Lazarus; R. L. Hester,

2005-08-01

Milling tests were run on families of High Speed Steel (HSS) end mills to determine their lives while machining 304 Stainless Steel. The end mills tested were made from M7, M42 and T15-CPM High Speed Steels. The end mills were also evaluated with no coatings as well as with Titanium Nitride (TiN) and Titanium Carbo-Nitride (TiCN) coatings to determine which combination of HSS and coating provided the highest increase in end mill life while increasing the cost of the tool the least. We found end mill made from M42 gave us the largest increase in tool life with the least increase in cost. The results of this study will be used by Cutting Tool Engineering in determining which end mill descriptions will be dropped from our tool catalog.

Bioconversion of paper mill sludge to bioethanol in the presence of accelerants or hydrogen peroxide pretreatment.

Science.gov (United States)

Gurram, Raghu Nandan; Al-Shannag, Mohammad; Lecher, Nicholas Joshua; Duncan, Shona M; Singsaas, Eric Lawrence; Alkasrawi, Malek

2015-09-01

In this study we investigated the technical feasibility of convert paper mill sludge into fuel ethanol. This involved the removal of mineral fillers by using either chemical pretreatment or mechanical fractionation to determine their effects on cellulose hydrolysis and fermentation to ethanol. In addition, we studied the effect of cationic polyelectrolyte (as accelerant) addition and hydrogen peroxide pretreatment on enzymatic hydrolysis and fermentation. We present results showing that removing the fillers content (ash and calcium carbonate) from the paper mill sludge increases the enzymatic hydrolysis performance dramatically with higher cellulose conversion at faster rates. The addition of accelerant and hydrogen peroxide pretreatment further improved the hydrolysis yields by 16% and 25% (g glucose / g cellulose), respectively with the de-ashed sludge. The fermentation process of produced sugars achieved up to 95% of the maximum theoretical ethanol yield and higher ethanol productivities within 9h of fermentation. Copyright © 2015 Elsevier Ltd. All rights reserved.

Sustainability Issues and Opportunities in the Sugar and Sugar-Bioproduct Industries

Directory of Open Access Journals (Sweden)

Gillian Eggleston

2015-09-01

Full Text Available Like many other industries, the sugar and sugar-bioproduct industries are facing important sustainability issues and opportunities. The relatively low and fluctuating profit for sugar, surpluses of sugar, world-wide trend to produce alternative, renewable bio-based fuels and chemicals to those derived from petroleum and reduce greenhouse gases, water- and energy-intensive factories and refineries, and increased consumer demands for sustainably manufactured products are putting pressure on the industries to diversify for sustainability. Sugar crops, including sugar and energy cane (Saccharum officinarum, sugar and energy beets (Beta vulgaris, and sweet sorghum (Sorghum bicolor L. Moench, are excellent, renewable biomass feedstocks because of their availability, their being amongst the plants that give the highest yields of carbohydrates per hectare, and high sugar contents. While much research has been focused on conversion technologies for advanced biofuels and bioproducts, attention is now focused on developing sustainable supply chains of sugar feedstocks for the new, flexible biorefineries, with customers wanting maximum feedstock reliability and quality, while minimizing cost. All biomass from sugar crops are potential feedstocks. The cogeneration of bioelectricity from bagasse and leaf residues is being increasingly manufactured in more countries and, due to the high carbon content of bagasse and leaves, can also be converted into value-added products such as biochar. Sugar crops are superior feedstocks for the production of platform chemicals for the manufacture of a range of end-products, e.g., bioplastics, chemicals, and biomaterials. In several countries and regions, green sustainability criteria are now in place and have to be met to count against national biofuel targets. Processes to convert high-fiber sugar crop biomass into biofuel have been developed but there has only been limited commercialization at the large-scale.

Bioassay for uranium mill tailings

International Nuclear Information System (INIS)

Tschaeche, A.N.

1986-01-01

Uranium mill tailings are composed of fine sand that contains, among other things, some uranium (U/sup 238/ primarily), and all of the uranium daughters starting with /sup 230/Th that are left behind after the usable uranium is removed in the milling process. Millions of pounds of tailings are and continue to be generated at uranium mills around the United States. Discrete uranium mill tailings piles exist near the mills. In addition, the tailings materials were used in communities situated near mill sites for such purposes as building materials, foundations for buildings, pipe runs, sand boxes, gardens, etc. The Uranium Mill Tailings Remedial Action Project (UMTRAP) is a U.S. Department of Energy Program designed with the intention of removing or stabilizing the mill tailings piles and the tailings used to communities so that individuals are not exposed above the EPA limits established for such tailings materials. This paper discusses the bioassay programs that are established for workers who remove tailings from the communities in which they are placed

Role of potassium and nitrogen on sugar concentration of sugar beet

African Journals Online (AJOL)

Sugar is obtained from root of sugar beet (Beta vulgaris L.) in addition to other sources. Three important economic parameters are often considered and these are root yield, sugar concentration in root juice and total sugar yield. All the three are affected by cropping period and use of fertilisers. Existing literature suggests the ...

Biomass torrefaction mill

Science.gov (United States)

Sprouse, Kenneth M.

2016-05-17

A biomass torrefaction system includes a mill which receives a raw biomass feedstock and operates at temperatures above 400 F (204 C) to generate a dusty flue gas which contains a milled biomass product.

The equipment supply industry to sugar mills, ethanol and energy in Brazil: an analysis based in leading companies and key-organizations of sector and of LPA of Sertãozinho

Directory of Open Access Journals (Sweden)

Michelle Castro Carrijo

2015-12-01

Full Text Available This study aims to analyze the profile, organization, efficiency and innovation in the supply industry equipment for sugar mills, ethanol and energy in Brazil, contributing to an important discussion on the competitiveness of this industry. Therefore, the study was based on analysis of information obtained from two surveys: the first held with representative organizations and two industry-leading companies located in the cities of Sertãozinho and Piracicaba; and the second, through interviews with companies in the Local Productive Arrangement (LPA of Sertãozinho, known as the Silicon Valley Ethanol. The results suggest that the increasing modernization of the sector will require greater efforts from equipment industry to provide plants with the necessary technological innovations and potential efficiency gains and that the constituent companies of this industry, few invest in technology and professional training, in other words, are lacking in management training, which leads to loss of valuable opportunities, international market share is tiny, most companies turn to private sources of financing, and companies seem unaware of the real benefits of cooperation, although they appear in most companies in this industry.

Passa-se uma engenhoca: ou como se faziam transações com terras, engenhos e crédito em mercados locais e imperfeitos (freguesia de Campo Grande, Rio de Janeiro, séculos XVIII e XIX 'Engenhocas' to sell!: or lands, sugar mills and credit’s trade in local and imperfect markets (Campo Grande civil parish, Rio de Janeiro, Brazil, XVIII-XIX centuries

Directory of Open Access Journals (Sweden)

Manoela Pedroza

2010-06-01

Full Text Available A questão central deste artigo é perceber como as hierarquias sociais e as políticas específicas do Antigo Regime nos Trópicos se refletiram em estratégias concretas, e compreender as engrenagens locais de um mercado imperfeito. Analisaremos as escolhas e trajetórias de agentes envolvidos em transações com terras, engenhos e concessão de crédito na freguesia de Campo Grande, no correr do século XVIII até o início do XIX, cuja especificidade foi conseguirem reproduzir sua condição senhorial. Metodologicamente, partimos da microanálise e compusemos redes sociais locais que sustentaram as estratégias dos agentes em questão. Propomos que as rendas criadas a partir das vendas a prazo, os vínculos pessoais entre compradores-credores-vendedores-devedores nas vendas dos engenhos e a sobreposição de vínculos de dependência locais foram fatores que possibilitaram a acumulação econômica e a reprodução ampliada da condição senhorial.Using the concept of ‘Ancien Régime on the Tropics’, this article aims to investigate how social hierarchies and politics in Brazil, during the 18th century, reflected into concrete local strategies. Our objective is to understand the gadgets of an imperfect market, based on agents’ choices who were all involved in lands, sugar mills and credit commercial transactions in the Campo Grande civil parish, in the Rio de Janeiro. All agents had gotten to reproduce its extended senhorial condition. Our methodology is based on microanalysis, so we composed local social nets we guest had supported the agents’ strategies in question. We consider strategies to achieve long term incomes; bonds between purchaser, creditor, salesman and debtors (both involving sugar mills commercial transactions; the overlapping of dependence bonds by strategic exchanges created by sugar mill masters among consanguineous, matrimonial and fictitious relatives had been factors that made possible the economic accumulation

Managing your blood sugar

Science.gov (United States)

Hyperglycemia - control; Hypoglycemia - control; Diabetes - blood sugar control; Blood glucose - managing ... sugar ( hypoglycemia ) Recognize and treat high blood sugar ( hyperglycemia ) Plan healthy meals Monitor your blood sugar (glucose) ...

Evolution of Lignocellulosic Macrocomponents in the Wastewater Streams of a Sulfite Pulp Mill: A Preliminary Biorefining Approach

Directory of Open Access Journals (Sweden)

Tamara Llano

2015-01-01

Full Text Available The evolution of lignin, five- and six-carbon sugars, and other decomposition products derived from hemicelluloses and cellulose was monitored in a sulfite pulp mill. The wastewater streams were characterized and the mass balances throughout digestion and total chlorine free bleaching stages were determined. Summative analysis in conjunction with pulp parameters highlights some process guidelines and valorization alternatives towards the transformation of the traditional factory into a lignocellulosic biorefinery. The results showed a good separation of cellulose (99.64% during wood digestion, with 87.23% of hemicellulose and 98.47% lignin dissolved into the waste streams. The following steps should be carried out to increase the sugar content into the waste streams: (i optimization of the digestion conditions increasing hemicellulose depolymerization; (ii improvement of the ozonation and peroxide bleaching stages, avoiding deconstruction of the cellulose chains but maintaining impurity removal; (iii fractionation of the waste water streams, separating sugars from the rest of toxic inhibitors for 2nd generation biofuel production. A total of 0.173 L of second-generation ethanol can be obtained in the spent liquor per gram of dry wood. The proposed methodology can be usefully incorporated into other related industrial sectors.

Turkish Undergraduates' Misconceptions of Evaporation, Evaporation Rate, and Vapour Pressure

Science.gov (United States)

Canpolat, Nurtac

2006-01-01

This study focused on students' misconceptions related to evaporation, evaporation rate, and vapour pressure. Open-ended diagnostic questions were used with 107 undergraduates in the Primary Science Teacher Training Department in a state university in Turkey. In addition, 14 students from that sample were interviewed to clarify their written…

Use and treatment of olive mill wastewater: current situation and prospects in Spain

Directory of Open Access Journals (Sweden)

Fiestas Ros de Ursinos, J. A.

1992-04-01

Full Text Available The characteristics of olive mill wastewater are set out the viewpoint of their pollutant capacity and the problems arising from their tipping in olive-growing areas. The national administration's solutions for preventing pollutions of surface waters are also stated. Special detail is given to the action taken within a research and development program financed by the Spanish Government and the EEC through the Commission MEDSPA 89 for the technical-economic evaluation of different systems for eliminating and treating olive mill wastewater, in order to determine the feasibility of their introduction at industrial level. At the same time the systems currently under evaluation are described: - Intensification of natural evaporation from olive mill wastewater stored in ponds (two systems. - Physical processes using forced evaporation to eliminate the olive mill wastewater, followed by aerobic biological processes or systems of ultrafiltration and inverse osmosis for final treatment of the condensate (two systems. - Application of physico-chemical processes to eliminate the greater part of the organic components of the olive mill wastewaters and the use of aerobic biological processes or systems of ultrafiltration and inverse osmosis for final treatment of the clarified fraction (three systems. - Biological process for the complete treatment of the olive mill wastewaters by the successive application of processes: bioconversion, biomethanisation, aerobic treatment, and physico-chemical treatment. Treatment yields of the order of 99,6% are achieved, at the same time obtaining by-products of commercial interest (one system.

Las características de los alpechines se establecen desde el punto de vista de su capacidad contaminante y de los problemas típicos que surgen en las zonas de cultivo del olivo. También están descritas las soluciones de la administración del Estado para la prevención de la contaminación de aguas de superficie

Use of glutaraldehyde and benzalkonium chloride for minimizing post-harvest physio-chemical and microbial changes responsible for sucrose losses in sugar cane.

Science.gov (United States)

Singh, Pushpa; Arya, Namita; Tiwari, Priyanka; Suman, Archna; Rai, R K; Shrivastava, A K; Solomon, S

2008-08-27

Sugar cane is sensitive to enormous sucrose losses induced by physio-chemical and microbial changes, the severity being increased during the time lag between harvest and crushing in the mills. Minimization of the sucrose losses in the field is essential for better sugar recovery and prevention of sucrose losses. An experiment was conducted to evaluate the efficacy of glutaraldehyde and benzalkonium chloride for their effects on the microbial counts and physio-chemical changes responsible for sucrose losses. Glutaraldehyde and benzalkonium chloride (1000 + 250 ppm) reduced the losses in sucrose content to 7.1% as compared to the 30.8% loss in the control, thus improving the performance by 76.9%. The application of chemicals reduced the acid invertase activity (by 60%), lowered weight loss, titrable acidity, reducing sugars content, dextran, ethanol, and ethylene production and respiration rates. The application led to the reduction in the total bacterial, fungal, Leuconostoc, and yeast counts by 67.92, 51.3%, 26.08, and 51.2%, respectively.

Continuous bio-catalytic conversion of sugar mixture to acetone-butanol-ethanol by immobilized Clostridium acetobutylicum DSM 792.

Science.gov (United States)

Survase, Shrikant A; van Heiningen, Adriaan; Granström, Tom

2012-03-01

Continuous production of acetone, n-butanol, and ethanol (ABE) was carried out using immobilized cells of Clostridium acetobutylicum DSM 792 using glucose and sugar mixture as a substrate. Among various lignocellulosic materials screened as a support matrix, coconut fibers and wood pulp fibers were found to be promising in batch experiments. With a motive of promoting wood-based bio-refinery concept, wood pulp was used as a cell holding material. Glucose and sugar mixture (glucose, mannose, galactose, arabinose, and xylose) comparable to lignocellulose hydrolysate was used as a substrate for continuous production of ABE. We report the best solvent productivity among wild-type strains using column reactor. The maximum total solvent concentration of 14.32 g L(-1) was obtained at a dilution rate of 0.22 h(-1) with glucose as a substrate compared to 12.64 g L(-1) at 0.5 h(-1) dilution rate with sugar mixture. The maximum solvent productivity (13.66 g L(-1) h(-1)) was obtained at a dilution rate of 1.9 h(-1) with glucose as a substrate whereas solvent productivity (12.14 g L(-1) h(-1)) was obtained at a dilution rate of 1.5 h(-1) with sugar mixture. The immobilized column reactor with wood pulp can become an efficient technology to be integrated with existing pulp mills to convert them into wood-based bio-refineries.

State of weed infestation and features of sugar beet protection in Belarus

Directory of Open Access Journals (Sweden)

Soroka Sergey Vladimirovich

2006-01-01

Full Text Available The changes of phytosanitary situation recently taking place in sugar beet crops in the Republic of Belarus are shown. It is noticed that in the crop agrocoenosises there is a high infestation level caused by Japanese barnyard millet (Echinochloa crus-galli (L Pal. Beauv, field sowthistle (Sonchus arvensis L, chickweed (Stellaria media (L Vill, quick grass (Agropyron repens (L Pal Beauv, matricary (Matricaria perforate Merat, creeping thistle (Circium arvense (L scop, marsh woundwort (Stachus palustris L wild buckwheat (Polygonum convolvulus L, bristle stem hemp nettle (Galeopsis tetrahit L, common horsetail (Equisetum arvense L, field forget-me-not (Myosotis arvensis (L Hill, shepherd's purse (Capsella bursa-pastoris (L Med etc. Due to non-observance of preventive and separate agrotechnical techniques especially in spring-summer period, such weeds as bedstraw (Galium aparine L, white campion (Melandrium album (Mill Garcke, green amaranthus (Amaranthus retroflexus L started to appear in the crops. To protect sugar beet effectively, two variants of herbicides application are proposed. The first one - a combined, one stipulating soil action herbicides application before planting or before sugar beet seedlings emergence and on seedlings - to carry out two treatment by post-emergence preparations. The second variant, a split post- -emergence herbicide application (two-three times spraying on growing weeds at small application rates. In the next 5-6 years, a combined method will be of a primary importance in the conditions of the Republic.

Hydrothermal waves in evaporating sessile drops

OpenAIRE

Brutin, D.; Rigollet, F.; Niliot, C. Le

2009-01-01

Drop evaporation is a simple phenomena but still unclear concerning the mechanisms of evaporation. A common agreement of the scientific community based on experimental and numerical work evidences that most of the evaporation occurs at the triple line. However, the rate of evaporation is still empirically predicted due to the lack of knowledge on the convection cells which develop inside the drop under evaporation. The evaporation of sessile drop is more complicated than it appears due to the...

Alkali-aided enzymatic viscosity reduction of sugar beet mash for novel bioethanol production process

International Nuclear Information System (INIS)

Srichuwong, Sathaporn; Arakane, Mitsuhiro; Fujiwara, Maki; Zhang, Zilian; Takahashi, Hiroyuki; Tokuyasu, Ken

2010-01-01

Ethanol fermentation of fresh sugar beet mash (SBM) could give a benefit on reducing energy input for sugar diffusion, juice separation, and water evaporation as used in conventional practices, thus offering promise as a low energy process. Actions of cell-wall degrading enzymes provide a mash with low viscosity, which can be easily fermented to ethanol. However, a several-fold higher enzyme loading was required for viscosity reduction of SBM compared with that of potato mash. In this study, the use of dilute alkali treatment (0.025-0.15 N NaOH, 25 o C, 1 h) in enhancing enzymatic viscosity reduction of SBM was evaluated. The results showed that higher NaOH concentration enhanced demethylation and deacetylation of SBM, resulting in greater performances of the enzymes on reducing viscosity. Efficient enzymatic viscosity reduction of SBM was observed with the 0.1 N NaOH treatment. On the other hand, untreated SBM was highly resistant to viscosity reduction, even though a 20-fold more enzyme loading was used. The resulting mash containing 12-13% (w/v) sucrose yielded 7-8% (v/v) ethanol after 24 h of fermentation (90% efficiency). Accordingly, alkali treatment can be applied for facilitating the use of fresh sugar beet for ethanol production.

Simultaneous quantification of differently glycosylated, acetylated and 2,3-dihydro-2,5-dihydroxy-6-methyl-4h-pyran-4-one-conjugated soyasaponins using reversed-phase high-performance liquid chromatography with evaporative light scattering detection

NARCIS (Netherlands)

DeCroos, K.; Vincken, J.P.; Heng, L.; Bakker, R.; Gruppen, H.; Verstraete, W.

2005-01-01

A novel method utilizing high-performance liquid chromatography (HPLC) with evaporative light scattering detection (ELSD) and electrospray ionisation mass spectrometry (ESI-MS) was developed for the analysis of soyasaponins, a divers group of triterpenic compounds with one or two sugar side chains,

Decontamination effect of milling by a jet mill on bacteria in rice flour.

Science.gov (United States)

Sotome, Itaru; Nei, Daisuke; Tsuda, Masuko; Mohammed, Sharif Hossen; Takenaka, Makiko; Okadome, Hiroshi; Isobe, Seiichiro

2011-06-01

The decontamination effect of milling by a jet mill was investigated by counting the number of bacteria in brown and white rice flour with mean particle diameters of 3, 20, and 40µm prepared by the jet mill. In the jet mill, the particles are crushed and reduced in size by the mechanical impact caused by their collision. Although the brown and white rice grains were contaminated with approximately 10(6) and 10(5) CFU/g bacteria, the microbial load of the rice flour decreased as the mean particle diameter decreased, ultimately decreasing to approximately 104 and 103 CFU/g in the brown and white rice flour. The temperature and pressure changes of the sample were not considered to have an effect on reducing the bacterial count during the milling. Hence, it was thought that the rice flour was decontaminated by other effects.

Does evaporation paradox exist in China?

Directory of Open Access Journals (Sweden)

Z. T. Cong

2009-03-01

Full Text Available One expected consequence of global warming is the increase in evaporation. However, lots of observations show that the rate of evaporation from open pans of water has been steadily decreasing all over the world in the past 50 years. The contrast between expectation and observation is called "evaporation paradox". Based on data from 317 weather stations in China from 1956 to 2005, the trends of pan evaporation and air temperature were obtained and evaporation paradox was analyzed. The conclusions include: (1 From 1956 to 2005, pan evaporation paradox existed in China as a whole while pan evaporation kept decreasing and air temperature became warmer and warmer, but it does not apply to Northeast and Southeast China; (2 From 1956 to 1985, pan evaporation paradox existed narrowly as a whole with unobvious climate warming trend, but it does not apply to Northeast China; (3 From 1986 to 2005, in the past 20 years, pan evaporation paradox did not exist for the whole period while pan evaporation kept increasing, although it existed in South China. Furthermore, the trend of other weather factors including sunshine duration, windspeed, humidity and vapor pressure deficit, and their relations with pan evaporation are discussed. As a result, it can be concluded that pan evaporation decreasing is caused by the decreasing in radiation and wind speed before 1985 and pan evaporation increasing is caused by the decreasing in vapor pressure deficit due to strong warming after 1986. With the Budyko curve, it can be concluded that the actual evaporation decreased in the former 30 years and increased in the latter 20 year for the whole China.

Microwave heating type evaporator

International Nuclear Information System (INIS)

Taura, Masazumi; Nishi, Akio; Morimoto, Takashi; Izumi, Jun; Tamura, Kazuo; Morooka, Akihiko.

1987-01-01

Purpose: To prevent evaporization stills against corrosion due to radioactive liquid wastes. Constitution: Microwaves are supplied from a microwave generator by way of a wave guide tube and through a microwave permeation window to the inside of an evaporatization still. A matching device is attached to the wave guide tube for transmitting the microwaves in order to match the impedance. When the microwaves are supplied to the inside of the evaporization still, radioactive liquid wastes supplied from a liquid feed port by way of a spray tower to the inside of the evaporization still is heated and evaporated by the induction heating of the microwaves. (Seki, T.)

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

OpenAIRE

Garc?a Nieto, Paulino Jos?; Garc?a-Gonzalo, Esperanza; Ord??ez Gal?n, Celestino; Bernardo S?nchez, Antonio

2016-01-01

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism i...

Vapor-based interferometric measurement of local evaporation rate and interfacial temperature of evaporating droplets.

Science.gov (United States)

Dehaeck, Sam; Rednikov, Alexey; Colinet, Pierre

2014-03-04

The local evaporation rate and interfacial temperature are two quintessential characteristics for the study of evaporating droplets. Here, it is shown how one can extract these quantities by measuring the vapor concentration field around the droplet with digital holographic interferometry. As a concrete example, an evaporating freely receding pending droplet of 3M Novec HFE-7000 is analyzed at ambient conditions. The measured vapor cloud is shown to deviate significantly from a pure-diffusion regime calculation, but it compares favorably to a new boundary-layer theory accounting for a buoyancy-induced convection in the gas and the influence upon it of a thermal Marangoni flow. By integration of the measured local evaporation rate over the interface, the global evaporation rate is obtained and validated by a side-view measurement of the droplet shape. Advective effects are found to boost the global evaporation rate by a factor of 4 as compared to the diffusion-limited theory.

Thermogravimetric analysis of fuel film evaporation

Institute of Scientific and Technical Information of China (English)

HU Zongjie; LI Liguang; YU Shui

2006-01-01

Thermogravimetric analysis (TGA) was compared with the petrochemical distillation measurement method to better understand the characteristics of fuel film evaporation at different wall tem- peratures. The film evaporation characteristics of 90# gasoline, 93# gasoline and 0# diesel with different initial thicknesses were investigated at different environmental fluxes and heating rates. The influences of heating rate, film thickness and environmental flux on fuel film evaporation for these fuels were found. The results showed that the environmental conditions in TGA were similar to those for fuel films in the internal combustion engines, so data from TGA were suitable for the analysis of fuel film evaporation. TGA could simulate the key influencing factors for fuel film evaporation and could investigate the basic quantificational effect of heating rate and film thickness. To get a rapid and sufficient fuel film evaporation, sufficiently high wall temperature is necessary. Evaporation time decreases at a high heating rate and thin film thickness, and intense gas flow is important to promoting fuel film evaporation. Data from TGA at a heating rate of 100℃/min are fit to analyze the diesel film evaporation during cold-start and warming-up. Due to the tense molecular interactions, the evaporation sequence could not be strictly divided according to the boiling points of each component for multicomponent dissolved mixture during the quick evaporation process, and the heavier components could vaporize before reaching their boiling points. The 0# diesel film would fully evaporate when the wall temperature is beyond 250℃.

The Truth about Sugar.

Science.gov (United States)

Yeung, C Albert; Goodfellow, Ashley; Flanagan, Louise

2015-01-01

Sugars are used by the industry to enhance the attractiveness of foods and drinks. These added sugars, or 'free sugars', are not easily identified in food or drink labels. Certain manufactured foods and drinks with 'safe' names, such as dried fruit and fruit juice, still contain free sugars and can be confusing. Guidance states that daily consumption of free sugars should be less than 10% of total energy intake (no more than 5% in the UK). However, it is found that both tooth decay and obesity are associated with consumption of free sugars in large quantities and at inappropriate times.

Beneficial uses of paper mill residuals for New York State`s recycled-paper mills. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This report evaluates the New York paper mill industry in terms of the productive management and treatment of solid wastes. It identifies current efforts by recycling mills to beneficially use paper mill residuals (often called sludge) and suggests additional options that should be considered by the industry in general and individual mills in particular. It also examines the regulations and economics affecting the mills and suggests actions that could improve the industry`s ability to convert wastes to value-added products. The report recommends that the mills should continue measures to reduce fiber and filler clay losses, promote the transfer of usable fiber and clay to mills able to use them, upgrade sludge dewatering capabilities, and take a more regional approach to solid waste disposal problems. State agencies are urged to support these efforts, encourage the development and commercialization of new beneficial use technologies, and reduce regulatory barriers whenever possible.

Sugar-Sweetened Beverages Are the Main Sources of Added Sugar Intake in the Mexican Population.

Science.gov (United States)

Sánchez-Pimienta, Tania G; Batis, Carolina; Lutter, Chessa K; Rivera, Juan A

2016-09-01

Sugar intake has been associated with an increased prevalence of obesity, other noncommunicable diseases, and dental caries. The WHO recommends that free sugars should be ENSANUT (National Health and Nutrition Survey) 2012], which represents 3 geographic regions and urban and rural areas. Dietary information was obtained by administering a 24-h recall questionnaire to 10,096 participants. Total sugar intake was estimated by using the National Institute of Public Health (INSP) food-composition table and an established method to estimate added sugars. The mean intakes of total, intrinsic, and added sugars were 365, 127, and 238 kcal/d, respectively. Added sugars contributed 13% of TEI. Sugar-sweetened beverages (SSBs) were the main source of sugars, contributing 69% of added sugars. Food products high in saturated fat and/or added sugar (HSFAS) were the second main sources of added sugars, contributing 25% of added sugars. The average intake of added sugars in the Mexican diet is higher than WHO recommendations, which may partly explain the high prevalence of obesity and diabetes in Mexico. Because SSBs and HSFAS contribute >94% of total added sugars, strategies to reduce their intake should be strengthened. This includes stronger food labels to warn the consumer about the content of added sugars in foods and beverages. © 2016 American Society for Nutrition.

WTP Pilot-Scale Evaporation Tests

International Nuclear Information System (INIS)

QURESHI, ZAFAR

2004-01-01

This report documents the design, assembly, and operation of a Pilot-Scale Evaporator built and operated by SRTC in support of Waste Treatment Plant (WTP) Project at the DOE's Hanford Site. The WTP employs three identical evaporators, two for the Waste Feed and one for the Treated LAW. The Pilot-Scale Evaporator was designed to test simulants for both of these waste streams. The Pilot-Scale Evaporator is 1/76th scale in terms of evaporation rates. The basic configuration of forced circulation vacuum evaporator was employed. A detailed scaling analysis was performed to preserve key operating parameters such as basic loop configuration, system vacuum, boiling temperature, recirculation rates, vertical distances between important hardware pieces, reboiler heat transfer characteristics, vapor flux, configuration of demisters and water spray rings. Three evaporation test campaigns were completed. The first evaporation run used water in order to shake down the system. The water runs were important in identifying a design flaw that inhibited mixing in the evaporator vessel, thus resulting in unstable boiling operation. As a result the loop configuration was modified and the remaining runs were completed successfully. Two simulant runs followed the water runs. Test 1: Simulated Ultrafiltration Recycles with HLW SBS, and Test 2: Treated AN102 with Envelop C LAW. Several liquid and offgas samples were drawn from the evaporator facility for regulatory and non-regulatory analyses. During Test 2, the feed and the concentrate were spiked with organics to determine organic partitioning. The decontamination factor (DF) for Test 1 was measured to be 110,000 (more than the expected value of 100,000). Dow Corning Q2-3183A antifoam agent was tested during both Tests 1 and 2. It was determined that 500 ppm of this antifoam agent was sufficient to control the foaminess to less than 5 per cent of the liquid height. The long-term testing (around 100 hours of operation) did not show any

Ground-water conditions in the Grand County area, Utah, with emphasis on the Mill Creek-Spanish Valley area

Science.gov (United States)

Blanchard, Paul J.

1990-01-01

The Grand County area includes all of Grand County, the Mill Creek and Pack Creek drainages in San Juan County, and the area between the Colorado and Green Rivers in San Juan County. The Grand County area includes about 3,980 square miles, and the Mill Creek-Spanish Valley area includes about 44 square miles. The three principal consolidated-rock aquifers in the Grand County area are the Entrada, Navajo, and Wingate aquifers in the Entrada Sandstone, the Navajo Sandstone, and the Wingate Sandstone, and the principal consolidated-rock aquifer in the Mill Creek-Spanish Valley area is the Glen Canyon aquifer in the Glen Canyon Group, comprised of the Navajo Sandstone, the Kayenta Formation, and the Wingate Sandstone.Recharge to the Entrada, Navajo, and Glen Canyon aquifers typically occurs where the formations containing the aquifers crop out or are overlain by unconsolidated sand deposits. Recharge is enhanced where the sand deposits are saturated at a depth of more than about 6 feet below the land surface, and the effects of evaporation begin to decrease rapidly with depth. Recharge to the Wingate aquifer typically occurs by downward movement of water from the Navajo aquifer through the Kayenta Formation, and primarily occurs where the Navajo Sandstone, Kayenta Formation, and the Wingate Sandstone are fractured.

75 FR 60715 - Domestic Sugar Program-FY 2010 and FY 2011 Cane Sugar and Beet Sugar Marketing Allotments and...

Science.gov (United States)

2010-10-01

... marketing allotment and the associated production history will be transferred from MDFC to WSG, effective... Cane Sugar and Beet Sugar Marketing Allotments and Company Allocations AGENCY: Commodity Credit... publish the modifications to the fiscal year 2010 (FY 2010) State sugar marketing allotments and company...

Evaporation of Lennard-Jones clusters

International Nuclear Information System (INIS)

Roman, C.E.; Garzon, I.L.

1991-01-01

Extensive molecular dynamics simulations have been done to study the evaporation of a 13-atom Lennard-Jones cluster. The survival probability and the evaporative lifetime are calculated as a function of the cluster total energy from a classical trajectory analysis. The results are interpreted in terms of the RRK theory of unimolecular dissociation. The calculation of the binding energy of the evaporated species from the evaporation rate and the average kinetic energy release is discussed. (orig.)

Evaporation of inclined water droplets

Science.gov (United States)

Kim, Jin Young; Hwang, In Gyu; Weon, Byung Mook

2017-01-01

When a drop is placed on a flat substrate tilted at an inclined angle, it can be deformed by gravity and its initial contact angle divides into front and rear contact angles by inclination. Here we study on evaporation dynamics of a pure water droplet on a flat solid substrate by controlling substrate inclination and measuring mass and volume changes of an evaporating droplet with time. We find that complete evaporation time of an inclined droplet becomes longer as gravitational influence by inclination becomes stronger. The gravity itself does not change the evaporation dynamics directly, whereas the gravity-induced droplet deformation increases the difference between front and rear angles, which quickens the onset of depinning and consequently reduces the contact radius. This result makes the evaporation rate of an inclined droplet to be slow. This finding would be important to improve understanding on evaporation dynamics of inclined droplets. PMID:28205642

31 CFR Appendix A to Part 538 - Bulk Agricultural Commodities

Science.gov (United States)

2010-07-01

... Rice in the husk (paddy or rough) 1006.20 Husked (brown) Rice 1006.30 Semi-milled or wholly milled Rice....91 Sugar Beets, fresh, chilled, frozen or dried 1212.92 Sugar Cane, fresh, chilled, frozen or dried 1701.11 Cane Sugar, raw, solid form 1701.12 Beet Sugar, raw, solid form 1701.91 Cane or Beet Sugar...

31 CFR Appendix B to Part 560 - Bulk Agricultural Commodities

Science.gov (United States)

2010-07-01

... Rice in the husk (paddy or rough) 1006.20 Husked (brown) Rice 1006.30 Semi-milled or wholly milled Rice....91 Sugar Beets, fresh, chilled, frozen or dried 1212.92 Sugar Cane, fresh, chilled, frozen or dried 1701.11 Cane Sugar, raw, solid form 1701.12 Beet Sugar, raw, solid form 1701.91 Cane or Beet Sugar...

A proposal of a Planning Strategy in Order to Improve in the Production Process at the UEB Sugar Mill “Paquito Rosales”

Directory of Open Access Journals (Sweden)

Rubén Guillermo Pellicer-Durán

2015-11-01

Full Text Available This scientific research constitutes a part of the universitary project entitled “An attempt to improve the food production processes at some Unidades Empresariales de Base (UEB in the Santiago de Cuba´s province. This study is carried out inside the process that is taking place in order to redesign the Cuban sugar industry.This research work aims to suggest a strategy to increase the sugar of cane production levels taking into account some problems that are related to planning in the sugar production process. This is well represented through an strategic analysis that leads to the collection , processing and analysis of the primary information.These actions have an influence on the increase of the output base 96 in a 12 % and the growing of the recovery levels in 89,14 %. It is also estimated that the production rises on a 16,6 %.

Effects of bagging on sugar metabolism and the activity of sugar ...

African Journals Online (AJOL)

To investigate the effects of bagging on sugar metabolism and the activity of sugar metabolism related enzymes in Qingzhong loquat fruit development, the contents of sucrose, glucose and soluble solids as well as the activities of sugar metabolism related enzymes were evaluated. The content of sucrose, glucose and ...

Airborne effluent control at uranium mills

International Nuclear Information System (INIS)

Sears, M.B.

1976-01-01

The Oak Ridge National Laboratory has made an engineering cost--environmental benefit study of radioactive waste treatment systems for decreasing the amount of radioactive materials released from uranium ore processing mills. This paper summarizes the results of the study which pertain to the control and/or abatement of airborne radioactive materials from the mill processes. The tailings area is not included. Present practices in the uranium milling industry, with particular emphasis on effluent control and waste management, have been surveyed. A questionnaire was distributed to each active mill in the United States. Replies were received from about 75 percent of the mill operators. Visits were made to six operating uranium mills that were selected because they represented the different processes in use today and the newest, most modern in mill designs. Discussions were held with members of the Region IV Office of NRC and the Grand Junction Office of ERDA. Nuclear Science Abstracts, as well as other sources, were searched for literature pertinent to uranium mill processes, effluent control, and waste management

FM Interviews: Stephanie Mills

OpenAIRE

Valauskas, Edward

2002-01-01

Stephanie Mills is an author, editor, lecturer and ecological activist who has concerned herself with the fate of the earth and humanity since 1969, when her commencement address at Mills College in Oakland, Calif., drew the attention of a nation. Her speech, which the New York Times called "perhaps the most anguished statement" of the year's crop of valedictory speeches, predicted a bleak future. According to Mills, humanity was destined for suicide, the result of overpopulation and overuse ...

Dynamic behavior of a multi-effect sugar concentrator system

International Nuclear Information System (INIS)

Aly, N.H.; Marwan, M.A.

1994-01-01

A transient mathematical model is developed to simulate the dynamic response of multi effect evaporator for sugar distiller concentrators at delta company, Egypt. Based on the mass and energy balance equations, a non linear mathematical model relating the system variables is obtained. This model allows to investigate the response of the unit parameters in both steady state and transient operating condition. Also, the response of the unit to perturbations in feed syrup, flow rate, concentration and heating steam temperature is studied. The predicted response based on the solution of the mathematical model is illustrated. The developed model proved to be efficient and capable to predict different operating conditions at steady state or transients variations. The study shows that an increase in heating steam temperature can be a critical factor due to caramelization of the syrup. 1 tab., 10 fig

Rough mill simulator version 3.0: an analysis tool for refining rough mill operations

Science.gov (United States)

Edward Thomas; Joel Weiss

2006-01-01

ROMI-3 is a rough mill computer simulation package designed to be used by both rip-first and chop-first rough mill operators and researchers. ROMI-3 allows users to model and examine the complex relationships among cutting bill, lumber grade mix, processing options, and their impact on rough mill yield and efficiency. Integrated into the ROMI-3 software is a new least-...

Evaporative and Convective Instabilities for the Evaporation of a Binary Mixture in a Bilayer System

Science.gov (United States)

Guo, Weidong; Narayanan, Ranga

2006-11-01

Evaporative convection in binary mixtures arises in a variety of industrial processes, such as drying of paint and coating technology. There have been theories devoted to this problem either by assuming a passive vapor layer or by isolating the vapor fluid dynamics. Previous work on evaporative and convective instabilities in a single component bilayer system suggests that active vapor layers play a major role in determining the instability of the interface. We have investigated the evaporation convection in binary mixtures taking into account the fluid dynamics of both phases. The liquid mixture and its vapor are assumed to be confined between two horizontal plates with a base state of zero evaporation but with linear vertical temperature profile. When the vertical temperature gradient reaches a critical value, the evaporative instability, Rayleigh and Marangoni convection set in. The effects of vapor and liquid depth, various wave numbers and initial composition of the mixture on the evaporative and convective instability are determined. The physics of the instability are explained and detailed comparison is made between the Rayleigh, Marangoni and evaporative convection in pure component and those in binary mixtures.

Techno-Economic Analysis of the Optimum Softwood Lignin Content for the Production of Bioethanol in a Repurposed Kraft Mill

Directory of Open Access Journals (Sweden)

Shufang Wu

2014-09-01

Full Text Available Kraft pulping is one possible pretreatment for softwood to economically produce bioethanol. This work evaluates the techno-economic potential of using the kraft process for producing bioethanol from softwoods in a repurposed or co-located kraft mill. Pretreated loblolly pine was enzymatically hydrolyzed at low enzyme dosages of 5 and 10 FPU/g of substrate. Pretreated residue with 13% lignin content had the highest sugar recovery, 32.7% and 47.7% at 5 and 10 FPU/g, respectively. The pretreated residues were oxygen delignified and refined. In all cases, oxygen delignification improved sugar recovery, while refining was mostly effective for pulps with high lignin content. At 5 FPU/g, the sugar recovery for all kraft pulps was 51 to 53% with oxygen delignification and refining. Increasing the enzyme dosage to 10 FPU/g increased the sugar recovery for these pulps to greater than 60%. Economic analysis for the pulps with different initial lignin content showed that kraft pulps with an initial lignin content of 6.7% with oxygen delignification had an ethanol yield of 285 L/ODt wood and the lowest total production cost of $0.55/L. Pulps with initial lignin content of 18.6% had a total production cost of $0.64/L with an ethanol yield of 264 L/ODt wood.

Liquid evaporation process and evaporator

International Nuclear Information System (INIS)

Bergey, Claude; Ravenel, Jacques.

1975-01-01

The process described enables a liquid to be evaporated rapidly without any projection. A jet of hot gas is applied to the liquid, the power and angle of the jet being chosen so as to spin the liquid. It is particularly used in the case of radioactive products [fr

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data.

Science.gov (United States)

García Nieto, Paulino José; García-Gonzalo, Esperanza; Ordóñez Galán, Celestino; Bernardo Sánchez, Antonio

2016-01-28

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC-MARS-based model was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc . Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC-MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

Directory of Open Access Journals (Sweden)

Paulino José García Nieto

2016-01-01

Full Text Available Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC in combination with multivariate adaptive regression splines (MARS technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC–MARS-based model was successfully used here to predict the milling tool flank wear (output variable as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC–MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

Science.gov (United States)

García Nieto, Paulino José; García-Gonzalo, Esperanza; Ordóñez Galán, Celestino; Bernardo Sánchez, Antonio

2016-01-01

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC–MARS-based model was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC–MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed. PMID:28787882

Putting evaporators to work: wiped film evaporator for high level wastes

International Nuclear Information System (INIS)

Dierks, R.D.; Bonner, W.F.

1976-01-01

At Battelle, Pacific Northwest Laboratories, a pilot scale, wiped film evaporator was tested for concentrating high level liquid wastes from Purex-type nuclear fuel recovery processes. The concentrates produced up to 60 wt-percent total solids; and the simplicity of operation and design of the evaporator gave promise for low maintenance and high reliability

Effect of milling time on microstructure and properties of Nano-titanium polymer by high-energy ball milling

Science.gov (United States)

Wang, Bo; Wei, Shicheng; Wang, Yujiang; Liang, Yi; Guo, Lei; Xue, Junfeng; Pan, Fusheng; Tang, Aitao; Chen, Xianhua; Xu, Binshi

2018-03-01

Nano-titanium (Nano-Ti) was prepared by high-energy ball milling from pure Ti power and grinding agents (Epoxy resin) at room temperature. The effect of milling time on structure and properties of Nano-Ti polymer were investigated systematically. The results show that high-energy ball milling is an effective way to produce Nano-Ti polymer. The dispersion stability and compatibility between Ti power and grinding agents are improved by prolonging the milling time at a certain degree, that is to say, the optimization milling time is 240 min. The particle size of Ti powder and the diffraction peaks intensity of Ti decrease obviously as the milling time increases due to the compression stress, shear friction and other mechanical forces are formed during ball milling. FT-IR result displays that the wavenumber of all the bands move to lower wavenumber after ball milling, and the epoxy ring is open. The system internal energy rises owing to the broken epoxy group and much more Nano-Ti is formed to promote the grafting reaction between Nano-Ti and epoxy resin. The results from TEM and XPS also prove that. And the grafting ration is maximum as the milling time is 240 min, the mass loss ratio is 17.53%.

Stable isotopic carbon composition of apples and their subfractions--juice, seeds, sugars, and nonvolatile acids.

Science.gov (United States)

Lee, H S; Wrolstad, R E

1988-01-01

The 13C:12C ratios of 8 authentic apple juice samples and their subfractions were determined by mass spectrometry. Apples from Argentina, Mexico, New Zealand, and the United States were processed into juice; pulp was collected from the milled fruit and seeds were collected from the press-cake. Sugars, nonvolatile acids, and phenolics were isolated from the juice by treatment with ion-exchange resins and polyvinylpyrrolidone (PVPP). The mean value for all juice samples was -24.2% which is close to the values reported by other investigators. Juice from apples grown in Argentina, Mexico, and New Zealand did not differ from U.S. samples. The isotopic composition of the subfractions ranged from -22.0 to -31.0%. The values for the pulp were essentially the same as for juice. The sugar fraction was slightly less negative than the juice; the nonvolatile acid and phenolic fractions were more negative. The levels of nonvolatile acids and phenolics in apple juice are low, however, so these compounds contribute little to overall delta 13C values in juice.

Method for determining the composition of the sugar moiety of a sugar containing compound

DEFF Research Database (Denmark)

2016-01-01

The present invention relates to methods of labeling sugar moieties of sugar containing compounds including glycopeptides. The compounds presented in the present invention facilitate reliable detection of sugar moieties of sugar containing compounds by a combination of spectroscopy methods...

STATISTICAL ANALYSIS OF RAW SUGAR MATERIAL FOR SUGAR PRODUCER COMPLEX

OpenAIRE

A. A. Gromkovskii; O. I. Sherstyuk

2015-01-01

Summary. In the article examines the statistical data on the development of average weight and average sugar content of sugar beet roots. The successful solution of the problem of forecasting these raw indices is essential for solving problems of sugar producing complex control. In the paper by calculating the autocorrelation function demonstrated that the predominant trend component of the growth raw characteristics. For construct the prediction model is proposed to use an autoregressive fir...

SUGAR-SWEETENED BEVERAGE, SUGAR INTAKE OF INDIVIDUALS AND THEIR BLOOD PRESSURE: INTERMAP STUDY

Science.gov (United States)

Brown, Ian J.; Stamler, Jeremiah; Van Horn, Linda; Robertson, Claire E.; Chan, Queenie; Dyer, Alan R.; Huang, Chiang-Ching; Rodriguez, Beatriz L.; Zhao, Liancheng; Daviglus, Martha L.; Ueshima, Hirotsugu; Elliott, Paul

2011-01-01

The obesity epidemic has focused attention on relationships of sugars and sugar-sweetened beverages (SSB) to cardiovascular risk factors. Here we report cross-sectional associations of SSB, diet beverages, sugars with blood pressure (BP) for UK and USA participants of the International Study of Macro/Micro-nutrients and Blood Pressure (INTERMAP). Data collected includes four 24-h dietary recalls, two 24-h urine collections, eight BP readings, questionnaire data for 2,696 people ages 40-59 from 10 USA/UK population samples. Associations of SSB, diet beverages, and sugars (fructose, glucose, sucrose) with BP were assessed by multiple linear regression. Sugar-sweetened beverage intake related directly to BP, P-values 0.005 to Sugar-sweetened beverage intake higher by 1 serving/day (355 ml/24-h) was associated with systolic/diastolic BP differences of +1.6/+0.8 mm Hg (both P sugar-sodium interactions: for individuals with above-median 24-h urinary sodium excretion, fructose intake higher by 2 SD (5.6 %kcal) was associated with systolic/diastolic BP differences of +3.4/+2.2 mm Hg (both P sugar-BP differences for persons with higher sodium excretion, lend support to recommendations that intake of SSB, sugars, and salt be substantially reduced. PMID:21357284

Long-Term Effects of Olive oil Mill wastewater spreading on soil and olive trees

Energy Technology Data Exchange (ETDEWEB)

Ben rouina, B.; Ben Ahmed, C.; Boukhris, M.

2009-07-01

The olive oil extraction process produces huge amounts of liquid waste called olive mill waste water (OMWW). Large amounts of OMWW (30 million m{sup 3}) are produced in the Mediterranean regions that accounts for 95% of the total olive oil production worldwide. In Tunisia, OMWW constitutes a serious environmental problem due to the features associated with this type of agro-waste and to its diverse organic load which may reach values as high as 100 g/L and is mained with this type of agro-waste and to its diverse organic load which may reach values as high as 100 g/L is mainly due to sugars. lipids, phenols, and tannins. (Author)

Long-Term Effects of Olive oil Mill wastewater spreading on soil and olive trees

International Nuclear Information System (INIS)

Ben rouina, B.; Ben Ahmed, C.; Boukhris, M.

2009-01-01

The olive oil extraction process produces huge amounts of liquid waste called olive mill waste water (OMWW). Large amounts of OMWW (30 million m 3 ) are produced in the Mediterranean regions that accounts for 95% of the total olive oil production worldwide. In Tunisia, OMWW constitutes a serious environmental problem due to the features associated with this type of agro-waste and to its diverse organic load which may reach values as high as 100 g/L and is mained with this type of agro-waste and to its diverse organic load which may reach values as high as 100 g/L is mainly due to sugars. lipids, phenols, and tannins. (Author)

Evaporating firewalls

Science.gov (United States)

Van Raamsdonk, Mark

2014-11-01

In this note, we begin by presenting an argument suggesting that large AdS black holes dual to typical high-energy pure states of a single holographic CFT must have some structure at the horizon, i.e. a fuzzball/firewall, unless the procedure to probe physics behind the horizon is state-dependent. By weakly coupling the CFT to an auxiliary system, such a black hole can be made to evaporate. In a case where the auxiliary system is a second identical CFT, it is possible (for specific initial states) that the system evolves to precisely the thermofield double state as the original black hole evaporates. In this case, the dual geometry should include the "late-time" part of the eternal AdS black hole spacetime which includes smooth spacetime behind the horizon of the original black hole. Thus, if a firewall is present initially, it evaporates. This provides a specific realization of the recent ideas of Maldacena and Susskind that the existence of smooth spacetime behind the horizon of an evaporating black hole can be enabled by maximal entanglement with a Hawking radiation system (in our case the second CFT) rather than prevented by it. For initial states which are not finely-tuned to produce the thermofield double state, the question of whether a late-time infalling observer experiences a firewall translates to a question about the gravity dual of a typical high-energy state of a two-CFT system.

Focused ion beam milling of carbon fibres

International Nuclear Information System (INIS)

Huson, Mickey G.; Church, Jeffrey S.; Hillbrick, Linda K.; Woodhead, Andrea L.; Sridhar, Manoj; Van De Meene, Allison M.L.

2015-01-01

A focused ion beam has been used to mill both individual carbon fibres as well as fibres in an epoxy composite, with a view to preparing flat surfaces for nano-indentation. The milled surfaces have been assessed for damage using scanning probe microscopy nano-indentation and Raman micro-probe analysis, revealing that FIB milling damages the carbon fibre surface and covers surrounding areas with debris of disordered carbon. The debris is detected as far as 100 μm from the milling site. The energy of milling as well as the orientation of the beam was varied and shown to have an effect when assessed by Raman spectroscopy. - Highlights: • Focused ion beam (FIB) milling was used to mill flat surfaces on carbon fibres. • Raman spectroscopy showed amorphous carbon was generated during FIB milling. • The amorphous debris is detected as far as 100 μm from the milling site. • This surface degradation was confirmed by nano-indentation experiments.

Evaporation under vacuum condition

International Nuclear Information System (INIS)

Mizuta, Satoshi; Shibata, Yuki; Yuki, Kazuhisa; Hashizume, Hidetoshi; Toda, Saburo; Takase, Kazuyuki; Akimoto, Hajime

2000-01-01

In nuclear fusion reactor design, an event of water coolant ingress into its vacuum vessel is now being considered as one of the most probable accidents. In this report, the evaporation under vacuum condition is evaluated by using the evaporation model we have developed. The results show that shock-wave by the evaporation occurs whose behavior strongly depends on the initial conditions of vacuum. And in the case of lower initial pressure and temperature, the surface temp finally becomes higher than other conditions. (author)

Optimal Condition of Fenton's Reagent to Enhance the Alcohol Production from Palm Oil Mill Effluent (POME

Directory of Open Access Journals (Sweden)

Supawadee Sinnaraprasat

2011-07-01

Full Text Available Application of Fenton's reaction for a proper hydrolysis step is an essential and important step in obtaining a higher level of readily biodegradable sugars from palm oil mill effluent (POME for improving the alcohol production by using immobilized Clostridium acetobutylicum. The objective of this research was, therefore, to investigate the optimum condition of Fenton's reaction in terms of COD: H2O2 ratios (w/w and H2O2: Fe2+ ratios (molar ratio used to oxidize carbohydrate and high molecular organic compounds into simple sugars, which are further fermented into alcohol. The experiments were carried out at H2O2: Fe2+ ratios (molar ratios of 5, 10, 20, 30 and 40 and the COD: H2O2 ratios (w/w of 50, 70, 100 and 130 (initial COD about 50,000 mg/L. The total sugar concentrations and organic compounds biodegradability (BOD5/COD ratios were also used for investigating suitable conditions for Fenton's reaction. The concentration of Fenton's reagent at H2O2:Fe2+ and COD:H2O2 ratio of 20 and 130 was identified as the optimum operating condition for the highest simple sugars of about 0.865% and BOD5/COD ratios of 0.539. The alcohol productions were carried out in the continuous stirred tank reactors (CSTR under an anaerobic continuous immobilization system. At a hydraulic retention time of 12 hours and POME pH of 4.8, the maximum total ABE concentration of 495 mg/L and the ABE yield of 0.236 grams of ABE produced/gram of reducing sugars were achieved at the mixed polyvinyl alcohol (PVA and palm oil ash (POA ratio of 10 : 3.

Evaporation of Lennard-Jones fluids.

Science.gov (United States)

Cheng, Shengfeng; Lechman, Jeremy B; Plimpton, Steven J; Grest, Gary S

2011-06-14

Evaporation and condensation at a liquid/vapor interface are ubiquitous interphase mass and energy transfer phenomena that are still not well understood. We have carried out large scale molecular dynamics simulations of Lennard-Jones (LJ) fluids composed of monomers, dimers, or trimers to investigate these processes with molecular detail. For LJ monomers in contact with a vacuum, the evaporation rate is found to be very high with significant evaporative cooling and an accompanying density gradient in the liquid domain near the liquid/vapor interface. Increasing the chain length to just dimers significantly reduces the evaporation rate. We confirm that mechanical equilibrium plays a key role in determining the evaporation rate and the density and temperature profiles across the liquid/vapor interface. The velocity distributions of evaporated molecules and the evaporation and condensation coefficients are measured and compared to the predictions of an existing model based on kinetic theory of gases. Our results indicate that for both monatomic and polyatomic molecules, the evaporation and condensation coefficients are equal when systems are not far from equilibrium and smaller than one, and decrease with increasing temperature. For the same reduced temperature T/T(c), where T(c) is the critical temperature, these two coefficients are higher for LJ dimers and trimers than for monomers, in contrast to the traditional viewpoint that they are close to unity for monatomic molecules and decrease for polyatomic molecules. Furthermore, data for the two coefficients collapse onto a master curve when plotted against a translational length ratio between the liquid and vapor phase.

The water footprint of sweeteners and bio-ethanol from sugar cane, sugar beet and maize

NARCIS (Netherlands)

Gerbens-Leenes, Winnie; Hoekstra, Arjen Ysbert

2009-01-01

Sugar cane and sugar beet are used for sugar for human consumption. In the US, maize is used, amongst others, for the sweetener High Fructose Maize Syrup (HFMS). Sugar cane, sugar beet and maize are also important for bio-ethanol production. The growth of crops requires water, a scarce resource. The

Sugar palm (Argena pinnata). Potential of sugar palm for bio-ethanol production

OpenAIRE

Elbersen, H.W.; Oyen, L.P.A.

2010-01-01

The energetic and economic feasibility of bioethanol production from sugar palm is virtually unknown. A positive factor are the potentially very high yields while the long non-productive juvenile phase and the high labor needs can be seen as problematic. Expansion to large scale sugar palm cultivation comes with risks. Small-scale cultivation of sugar palm perfectly fits into local farming systems. In order to make a proper assessment of the value palm sugar as bio-ethanol crop more informati...

Film flow analysis for a vertical evaporating tube with inner evaporation and outer condensation

International Nuclear Information System (INIS)

Park, Il Seouk

2008-01-01

A numerical study for the flow, heat and mass transfer characteristics of the evaporating tube with the films flowing down on both the inside and outside tube walls has been carried out. The condensation occurs along the outside wall while the evaporation occurs at the free surface of the inside film. The transport equations for momentum and energy are parabolized by the boundary-layer approximation and solved by using the marching technique. The calculation domain of 2 film flow regions (evaporating and condensation films at the inside and outside tube wall respectively) and tube wall is solved simultaneously. The coupling technique for the problem with the 3 different regions and the 2 interfaces of them has been developed to calculated the temperature field. The velocity and temperature fields and the amount of the condensed and evaporated mass as well as the position where the evaporating film is completely dried out are successfully predicted for various inside pressures and inside film inlet flow rates

THE USE OF POROUS CERAMICS FOR EVAPORATIVE AND EVAPORATIVE – VAPOR –COMPRESSION SYSTEMS

Directory of Open Access Journals (Sweden)

Cheban D.N.

2013-04-01

Full Text Available The use of natural evaporative cooling is one of technical solutions of problem of energy efficiency in air conditioning systems. The use of evaporative cooling in the first combined cooling stage allows reducing the load on the condenser of the cooling machine due to reducing of the condensing temperature. This combination allows the use of this type of system in any climatic conditions, including regions with small water resources. Multi-porous ceramic structure is used in evaporative air coolers and water coolers in this case. The objective of this paper is to show advantages of the using of porous ceramic as a working attachment, and to show advantages of the proposed scheme of compression-evaporation systems in comparison with standard vapor compression systems. Experimental research proved the fact, that in the film mode cooling efficiency of air flow is between EA=0,6÷0,7 and is slightly dependent of water flow. For countries with hot and dry climate where reserves of water are limited, it is recommended to use cyclical regime with EA≈0,65 value, or to use channel regime with a value of EA≈0,55. This leads to considerable energy savings. It has been determined, that combined air conditioning system is completely closed on the consumption of water at the parameters of the outside air equal to tA =32ºC and XA>13g/kg (in system with direct evaporative cooling machine, and tA=32ºC and XA>12g/kg (in system with indirect evaporative cooling machine. With these parameters, the cost of water in evaporative cooling stage can be fully compensated by condensate from the evaporator chiller.

Surface Quality of Staggered PCD End Mill in Milling of Carbon Fiber Reinforced Plastics

Directory of Open Access Journals (Sweden)

Guangjun Liu

2017-02-01

Full Text Available Machined surface quality determines the reliability, wear resistance and service life of carbon fiber reinforced plastic (CFRP workpieces. In this work, the formation mechanism of the surface topography and the machining defects of CFRPs are proposed, and the influence of milling parameters and fiber cutting angles on the surface quality of CFRPs is obtained, which can provide a reference for extended tool life and good surface quality. Trimming and slot milling tests of unidirectional CFRP laminates are performed. The surface roughness of the machined surface is measured, and the influence of milling parameters on the surface roughness is analyzed. A regression model for the surface roughness of CFRP milling is established. A significance test of the regression model is conducted. The machined surface topography of milling CFRP unidirectional laminates with different fiber orientations is analyzed, and the effect of fiber cutting angle on the surface topography of the machined surface is presented by using a digital super depth-of-field microscope and scanning electron microscope (SEM. To study the influence of fiber cutting angle on machining defects, the machined topography under different fiber orientations is analyzed. The slot milling defects and their formation mechanism under different fiber cutting angles are investigated.

Free Sugar Profile in Cycads

Directory of Open Access Journals (Sweden)

Thomas Edward Marler

2014-10-01

Full Text Available The sugars fructose, glucose, maltose, and sucrose were quantified in seven tissues of Zamia muricata Willd. to determine their distribution throughout various organs of a model cycad species, and in lateral structural roots of 18 cycad species to determine the variation in sugar concentration and composition among species representing every cycad genus. Taproot and lateral structural roots contained more sugars than leaf, stem, female strobilus, or coralloid roots. For example, taproot sugar concentration was 6.4-fold greater than stem sugar concentration. The dominant root sugars were glucose and fructose, and the only detected stem sugar was sucrose. Sucrose also dominated the sugar profile for leaflet and coralloid root tissue, and fructose was the dominant sugar in female strobilus tissue. Maltose was a minor constituent of taproot, leaflet, and female strobilus tissue, but absent in other tissues. The concentration of total free sugars and each of the four sugars did not differ among genera or families. Stoichiometric relationships among the sugars, such as the quotient hexoses/disaccharides, differed among organs and families. Although anecdotal reports on cycad starch have been abundant due to its historical use as human food and the voluminous medical research invested into cycad neurotoxins, this is the first report on the sugar component of the non-structural carbohydrate profile of cycads. Fructose, glucose, and sucrose are abundant in cycad tissues, with their relative abundance highly contrasting among organs. Their importance as forms of carbon storage, messengers of information, or regulators of cycad metabolism have not been determined to date.

A study of the natural biodegradation of two-phase olive mill solid waste during its storage in an evaporation pond.

Science.gov (United States)

Borja, R; Sánchez, E; Raposo, F; Rincón, B; Jiménez, A M; Martín, A

2006-01-01

A study of the natural biodegradation of two-phase olive mill solid waste (OMSW) during its storage in an evaporation pond was carried out. This system is traditionally used as the final disposal of this waste or constitutes a previous stage before being processed by cogeneration or anaerobic digestion processes. A laboratory-scale pond with a total volume of 520 l was used. The experiment was carried out between December 2002 and August 2003 covering a total period of 269 days. During the experiment, the variations of temperature (outside and inside the pond), the effective volume of the OMSW in the pond, moisture content, total solids (TS), volatile solids (VS), the total chemical oxygen demand (TCOD), total volatile acids (TVA), pH and cumulative methane production as a function of the operation time were evaluated. The experimental results obtained showed that the characteristics of the two-phase OMSW in the pond were dependent on the time of operation and temperature. During the experiment, three periods were clearly observed and differentiated: (a) An initial period with a rapid reduction of moisture content and effective volume, with an increase of TS, VS and TCOD removals, a decrease of pH and an increase of TVA and methane production until day 21. (b) A second period of slow decrease of moisture content and effective volume, due to the decrease of the ambient temperature. This period took place between day 21 and days 120-150 of assay, and it was characterised by a slight change in the OMSW properties. (c) A third period where the characteristics of the waste in the pond changed considerably due to the increase of the temperature outside the pond. The methane gas production also showed an increase due to the increase of methanogenic activity with the increase of temperature. An empirical model to describe the changes of two-phase OMSW characteristics and methane production with the operation time was developed. The proposed model, based on the use of

Home blood sugar testing

Science.gov (United States)

Diabetes - home glucose testing; Diabetes - home blood sugar testing ... Usual times to test your blood sugar are before meals and at bedtime. Your provider may ask you to check your blood sugar 2 hours after a meal or ...

DWPF Recycle Evaporator Simulant Tests

International Nuclear Information System (INIS)

Stone, M

2005-01-01

Testing was performed to determine the feasibility and processing characteristics of an evaporation process to reduce the volume of the recycle stream from the Defense Waste Processing Facility (DWPF). The concentrated recycle would be returned to DWPF while the overhead condensate would be transferred to the Effluent Treatment Plant. Various blends of evaporator feed were tested using simulants developed from characterization of actual recycle streams from DWPF and input from DWPF-Engineering. The simulated feed was evaporated in laboratory scale apparatus to target a 30X volume reduction. Condensate and concentrate samples from each run were analyzed and the process characteristics (foaming, scaling, etc) were visually monitored during each run. The following conclusions were made from the testing: Concentration of the ''typical'' recycle stream in DWPF by 30X was feasible. The addition of DWTT recycle streams to the typical recycle stream raises the solids content of the evaporator feed considerably and lowers the amount of concentration that can be achieved. Foaming was noted during all evaporation tests and must be addressed prior to operation of the full-scale evaporator. Tests were conducted that identified Dow Corning 2210 as an antifoam candidate that warrants further evaluation. The condensate has the potential to exceed the ETP WAC for mercury, silicon, and TOC. Controlling the amount of equipment decontamination recycle in the evaporator blend would help meet the TOC limits. The evaporator condensate will be saturated with mercury and elemental mercury will collect in the evaporator condensate collection vessel. No scaling on heating surfaces was noted during the tests, but splatter onto the walls of the evaporation vessels led to a buildup of solids. These solids were difficult to remove with 2M nitric acid. Precipitation of solids was not noted during the testing. Some of the aluminum present in the recycle streams was converted from gibbsite to

Sugar from Palms

DEFF Research Database (Denmark)

Barfod, Anders

Throughout the tropics and subtropics a large number of products are derived from the sugar-rich sap tapped from palms. I will give an overview of the most important species being exploited, harvesting practices and yields. I will further provide insights in the biomechanmics of sugar...... transportation in palms, which remain an enigma. Finally, the prospects for developing palm sugar into a commodity of worlswide significance will be discussed....

Energy advantage of the cane bagasse in the sugar industry; Aprovechamiento energetico del bagazo de cana en la industria azucarera

Energy Technology Data Exchange (ETDEWEB)

Hernandez Alarcon, Luis Alfredo

1987-07-01

The present study makes an analysis of the production and bagasse consumption in Mexico related to those indicators that orient and affect the energy advantage of the fiber within the energy structure and global sugar energy balance of the subsector. This global analysis is at the end concentrated on the evaluation of the steam generators of a sugar mill, that like Casasano, went from burning fuel oil only until 1984, to use bagasse and fuel oil simultaneously, in an attempt to reduce its specific consumption of energy, one of highest of the country. In 1985, 534 thousand hectares of sugar cane were cultivated, with field yields of 68.8 t/ha; of the 36.7 million tons of sugar cane produced, 35.7 million were ground to obtain, in the 69 sugar mills of the country 3.2 million tons of sugar, satisfying again the national consumption. In the respective grinding season 12 million tons of humid bagasse, were produced, representing the 34.5% of the total of the ground sugar cane; this bagasse was dedicated in 86.5% to the steam generation, with an average ratio of 1.87 kg of steam per kg of bagasse, contributing to the own energy balance the equivalent of 17.6 trillions of kilo-calories that correspond to the 66.2% of the total energy consumed by the sector, being left 33.8% contributed by the fuel oil. In order to generate steam in 1985 it had installed 543859 HP used with a weighed efficiency of 56.4%, of which the 91.5% used, in simultaneous form bagasse and fuel oil, the 6.38% only fuel oil and the 2.1% only bagasse. In the Casasano sugar mill a similar analysis is made, ending with the evaluation of the energy advantage of the bagasse in their boilers and of the factors that influence the specific energy consumption. In this form one settles down that the bagasse consumed in the last grinding season was burned generating 1.4 kg of steam per kg of bagasse in boilers working with an efficiency of 60% and consuming 1,090 kg of steam per ton of ground sugar cane

Sugar Restriction Leads to Increased Ad Libitum Sugar Intake by Overweight Adolescents in an Experimental Test Meal Setting.

Science.gov (United States)

O'Reilly, Gillian A; Black, David S; Huh, Jimi; Davis, Jaimie N; Unger, Jennifer; Spruijt-Metz, Donna

2017-07-01

The impact of sugar restriction on subsequent sugar intake by overweight adolescents is unknown. Our aim was to examine the effect of sugar restriction on subsequent ad libitum sugar intake by overweight adolescents and whether habitual sugar intake and impulsivity influence the effect of sugar restriction on subsequent sugar intake. This was an in-laboratory crossover feeding trial with sugar-exposure and sugar-restriction conditions. Eighty-seven overweight Latino and African-American adolescents underwent both meal conditions in two separate 8-hour in-laboratory visits. Participants had access to ad libitum snack trays for 3 hours after the condition-specific meals. Ad libitum sugar intake during the snack period was measured at each visit. Habitual sugar intake and impulsivity were assessed at baseline. Repeated measures analysis of covariance was used to examine the within-person effect of meal condition on ad libitum sugar intake. Mixed models were used to examine the moderating effects of habitual sugar intake and impulsivity on the meal condition-ad libitum sugar intake relationship. Participants consumed more ad libitum sugar during the snack period in the sugar-restriction condition than in the sugar-exposure condition (sugar restriction=78.63±38.84 g, sugar exposure=70.86±37.73 g; F=9.64, P=0.002). There was no relationship between habitual sugar intake and how much ad libitum sugar participants consumed during either condition. Higher impulsivity was associated with greater ad libitum sugar intake during both conditions (sugar restriction: b=.029, standard error=.01, Poverweight adolescents restricted from sugar intake consume greater amounts of sugar when they are later given access to high-sugar foods. Overweight adolescents with higher impulsivity appear to consume greater amounts of sugar regardless of previous levels of sugar consumption. Compensatory sugar intake and trait impulsivity may have implications for dietary interventions in this

Yang-Mills gravity in biconformal space

International Nuclear Information System (INIS)

Anderson, Lara B; Wheeler, James T

2007-01-01

We write a gravity theory with Yang-Mills-type action using the biconformal gauging of the conformal group. We show that the resulting biconformal Yang-Mills gravity theories describe 4-dim, scale-invariant general relativity in the case of slowly changing fields. In addition, we systematically extend arbitrary 4-dim Yang-Mills theories to biconformal space, providing a new arena for studying flat-space Yang-Mills theories. By applying the biconformal extension to a 4-dim pure Yang-Mills theory with conformal symmetry, we establish a 1-1, onto mapping between a set of gravitational gauge theories and 4-dim, flat-space gauge theories

Complete oxidative conversion of lignocellulose derived non-glucose sugars to sugar acids by Gluconobacter oxydans.

Science.gov (United States)

Yao, Ruimiao; Hou, Weiliang; Bao, Jie

2017-11-01

Non-glucose sugars derived from lignocellulose cover approximately 40% of the total carbohydrates of lignocellulose biomass. The conversion of the non-glucose sugars to the target products is an important task of lignocellulose biorefining research. Here we report a fast and complete conversion of the total non-glucose sugars from corn stover into the corresponding sugar acids by whole cell catalysis and aerobic fermentation of Gluconobacter oxydans. The conversions include xylose to xylonate, arabinose to arabonate, mannose to mannonate, and galactose to galactonate, as well as with glucose into gluconate. These cellulosic non-glucose sugar acids showed the excellent cement retard setting property. The mixed cellulosic sugar acids could be used as cement retard additives without separation. The conversion of the non-glucose sugars not only makes full use of lignocellulose derived sugars, but also effectively reduces the wastewater treatment burden by removal of residual sugars. Copyright © 2017 Elsevier Ltd. All rights reserved.

Evaporation-triggered microdroplet nucleation and the four life phases of an evaporating Ouzo drop

Science.gov (United States)

Tan, Huanshu; Diddens, Christian; Lv, Pengyu; Kuerten, J. G. M.; Zhang, Xuehua; Lohse, Detlef

2016-01-01

Evaporating liquid droplets are omnipresent in nature and technology, such as in inkjet printing, coating, deposition of materials, medical diagnostics, agriculture, the food industry, cosmetics, or spills of liquids. Whereas the evaporation of pure liquids, liquids with dispersed particles, or even liquid mixtures has intensively been studied over the past two decades, the evaporation of ternary mixtures of liquids with different volatilities and mutual solubilities has not yet been explored. Here we show that the evaporation of such ternary mixtures can trigger a phase transition and the nucleation of microdroplets of one of the components of the mixture. As a model system, we pick a sessile Ouzo droplet (as known from daily life—a transparent mixture of water, ethanol, and anise oil) and reveal and theoretically explain its four life phases: In phase I, the spherical cap-shaped droplet remains transparent while the more volatile ethanol is evaporating, preferentially at the rim of the drop because of the singularity there. This leads to a local ethanol concentration reduction and correspondingly to oil droplet nucleation there. This is the beginning of phase II, in which oil microdroplets quickly nucleate in the whole drop, leading to its milky color that typifies the so-called “Ouzo effect.” Once all ethanol has evaporated, the drop, which now has a characteristic nonspherical cap shape, has become clear again, with a water drop sitting on an oil ring (phase III), finalizing the phase inversion. Finally, in phase IV, all water has evaporated, leaving behind a tiny spherical cap-shaped oil drop. PMID:27418601

Reducing water consumption in the paper mill; Paperitehtaan vedenkaeytoen vaehentaeminen (WACI) - EKY 02

Energy Technology Data Exchange (ETDEWEB)

Pekuri, T.; Pekkanen, A. [UPM-Kymmene Oyj, Valkeakoski (Finland)

1998-12-31

This WACI-project was divided into several subprojects, which were started with gathering of present knowledge and entering to laboratory and pilot tests. In some projects there were mill scale trials in water connections and internal purification systems. In the `Quality Demands of Water` subproject the process waters used in the printing paper machines of UPM-Kymmene were surveyed. Lab tests were made for the different applications like shower, washing, seal and dilution of internally purified circulation waters. In `Mechanical Pulp Washing` project the target was to study how the different water connections around the TMP washing press will affect the paper machine runnability. It was also started to develop separating technique for TMP fibre extractive. `Micro and Electroflotation` studies have been made mainly on pilot scale but also in new mill-scale unit. `Membrane Technology` research consisted of both lab, pilot and mill scale studies, where different membrane qualities with different process waters have been tested. `Evaporation` trials were made on pilot scale for different process waters and condensates and concentrates were analysed. Condensates were tested for different applications. The possibility to `Reuse Waste Water` concentrated mainly on how to remove the brown colour. `Simulations` were done to find out what will be the new dcs balance in different wet end processes after new water connections including so-called kidneys. In the `Paper Quality` subproject the effects of dcs on bonding ability of TMP fibres were studied on lab scale with artificial pitch component and also with circulation concentrates. This 2.5 year Tekes-project was completed at the end of April 1998. (orig.)

Reducing water consumption in the paper mill; Paperitehtaan vedenkaeytoen vaehentaeminen (WACI) - EKY 02

Energy Technology Data Exchange (ETDEWEB)

Pekuri, T; Pekkanen, A [UPM-Kymmene Oyj, Valkeakoski (Finland)

1999-12-31

This WACI-project was divided into several subprojects, which were started with gathering of present knowledge and entering to laboratory and pilot tests. In some projects there were mill scale trials in water connections and internal purification systems. In the `Quality Demands of Water` subproject the process waters used in the printing paper machines of UPM-Kymmene were surveyed. Lab tests were made for the different applications like shower, washing, seal and dilution of internally purified circulation waters. In `Mechanical Pulp Washing` project the target was to study how the different water connections around the TMP washing press will affect the paper machine runnability. It was also started to develop separating technique for TMP fibre extractive. `Micro and Electroflotation` studies have been made mainly on pilot scale but also in new mill-scale unit. `Membrane Technology` research consisted of both lab, pilot and mill scale studies, where different membrane qualities with different process waters have been tested. `Evaporation` trials were made on pilot scale for different process waters and condensates and concentrates were analysed. Condensates were tested for different applications. The possibility to `Reuse Waste Water` concentrated mainly on how to remove the brown colour. `Simulations` were done to find out what will be the new dcs balance in different wet end processes after new water connections including so-called kidneys. In the `Paper Quality` subproject the effects of dcs on bonding ability of TMP fibres were studied on lab scale with artificial pitch component and also with circulation concentrates. This 2.5 year Tekes-project was completed at the end of April 1998. (orig.)

Influence of rice sample preparation and milling procedures on milling quality appraisals

Science.gov (United States)

The objective of this research was to investigate the effect of sample preparation and milling procedure on milling quality appraisals of rough rice. Samples of freshly harvested medium-grain rice (M202) with different initial moisture contents (MCs) ranging from 20.2% to 25.1% (w.b.) were used for...

Influence of milling process on efavirenz solubility

Directory of Open Access Journals (Sweden)

Erizal Zaini

2017-01-01

Full Text Available Introduction: The aim of this study was to investigate the influence of the milling process on the solubility of efavirenz. Materials and Methods: Milling process was done using Nanomilling for 30, 60, and 180 min. Intact and milled efavirenz were characterized by powder X-ray diffraction, scanning electron microscopy (SEM, spectroscopy infrared (IR, differential scanning calorimetry (DSC, and solubility test. Results: The X-ray diffractogram showed a decline on peak intensity of milled efavirenz compared to intact efavirenz. The SEM graph depicted the change from crystalline to amorphous habit after milling process. The IR spectrum showed there was no difference between intact and milled efavirenz. Thermal analysis which performed by DSC showed a reduction on endothermic peak after milling process which related to decreasing of crystallinity. Solubility test of intact and milled efavirenz was conducted in distilled water free CO2with 0.25% sodium lauryl sulfate media and measured using high-performance liquid chromatography method with acetonitrile: distilled water (80:20 as mobile phases. The solubility was significantly increased (P < 0.05 after milling processes, which the intact efavirenz was 27.12 ± 2.05, while the milled efavirenz for 30, 60, and 180 min were 75.53 ± 1.59, 82.34 ± 1.23, and 104.75 ± 0.96 μg/mL, respectively. Conclusions: Based on the results, the solubility of efavirenz improved after milling process.

Respiration-dependent utilization of sugars in yeasts: a determinant role for sugar transporters.

Science.gov (United States)

Goffrini, Paola; Ferrero, Iliana; Donnini, Claudia

2002-01-01

In many yeast species, including Kluyveromyces lactis, growth on certain sugars (such as galactose, raffinose, and maltose) occurs only under respiratory conditions. If respiration is blocked by inhibitors, mutation, or anaerobiosis, growth does not take place. This apparent dependence on respiration for the utilization of certain sugars has often been suspected to be associated with the mechanism of the sugar uptake step. We hypothesized that in many yeast species, the permease activities for these sugars are not sufficient to ensure the high substrate flow that is necessary for fermentative growth. By introducing additional sugar permease genes, we have obtained K. lactis strains that were capable of growing on galactose and raffinose in the absence of respiration. High dosages of both the permease and maltase genes were indeed necessary for K. lactis cells to grow on maltose in the absence of respiration. These results strongly suggest that the sugar uptake step is the major bottleneck in the fermentative assimilation of certain sugars in K. lactis and probably in many other yeasts.

76 FR 50285 - Fiscal Year 2012 Tariff-Rate Quota Allocations for Raw Cane Sugar, Refined and Specialty Sugar...

Science.gov (United States)

2011-08-12

... for Raw Cane Sugar, Refined and Specialty Sugar and Sugar-Containing Products AGENCY: Office of the... quantity of the tariff-rate quotas for imported raw cane sugar, refined and specialty sugar and sugar...), the United States maintains tariff-rate quotas (TRQs) for imports of raw cane sugar and refined sugar...

Ray tissues as an indirect measure of relative sap-sugar concentration in sugar maple

Science.gov (United States)

Peter W. Garrett; Kenneth R. Dudzik; Kenneth R. Dudzik

1989-01-01

Attempts to correlate ray tissue as a percentage of total wood volume with sap-sugar concentrations of sugar maple progenies were unsuccessful. These results raise doubts about our ability to use a relatively constant value such as ray-tissue volume in a selection program designed to increase the sap-sugar concentration of sugar maple seedlings.

242-A evaporator safety analysis report

International Nuclear Information System (INIS)

CAMPBELL, T.A.

1999-01-01

This report provides a revised safety analysis for the upgraded 242-A Evaporator (the Evaporator). This safety analysis report (SAR) supports the operation of the Evaporator following life extension upgrades and other facility and operations upgrades (e.g., Project B-534) that were undertaken to enhance the capabilities of the Evaporator. The Evaporator has been classified as a moderate-hazard facility (Johnson 1990). The information contained in this SAR is based on information provided by 242-A Evaporator Operations, Westinghouse Hanford Company, site maintenance and operations contractor from June 1987 to October 1996, and the existing operating contractor, Waste Management Hanford (WMH) policies. Where appropriate, a discussion address the US Department of Energy (DOE) Orders applicable to a topic is provided. Operation of the facility will be compared to the operating contractor procedures using appropriate audits and appraisals. The following subsections provide introductory and background information, including a general description of the Evaporator facility and process, a description of the scope of this SAR revision,a nd a description of the basic changes made to the original SAR

242-A evaporator safety analysis report

Energy Technology Data Exchange (ETDEWEB)

CAMPBELL, T.A.

1999-05-17

This report provides a revised safety analysis for the upgraded 242-A Evaporator (the Evaporator). This safety analysis report (SAR) supports the operation of the Evaporator following life extension upgrades and other facility and operations upgrades (e.g., Project B-534) that were undertaken to enhance the capabilities of the Evaporator. The Evaporator has been classified as a moderate-hazard facility (Johnson 1990). The information contained in this SAR is based on information provided by 242-A Evaporator Operations, Westinghouse Hanford Company, site maintenance and operations contractor from June 1987 to October 1996, and the existing operating contractor, Waste Management Hanford (WMH) policies. Where appropriate, a discussion address the US Department of Energy (DOE) Orders applicable to a topic is provided. Operation of the facility will be compared to the operating contractor procedures using appropriate audits and appraisals. The following subsections provide introductory and background information, including a general description of the Evaporator facility and process, a description of the scope of this SAR revision,a nd a description of the basic changes made to the original SAR.

77 FR 57180 - Fiscal Year 2013 Tariff-rate Quota Allocations for Raw Cane Sugar, Refined and Specialty Sugar...

Science.gov (United States)

2012-09-17

... Sugar, Refined and Specialty Sugar, and Sugar-Containing Products AGENCY: Office of the United States... quantity of the tariff-rate quotas for imported raw cane sugar, refined and specialty sugar, and sugar... imports of raw cane sugar and refined sugar. Pursuant to Additional U.S. Note 8 to Chapter 17 of the HTS...

Tool Wear Analysis on Five-Axis Flank Milling for Curved Shape Part – Full Flute and Ground Shank End Mill

Directory of Open Access Journals (Sweden)

Syahrul Azwan Sundi

2017-01-01

Full Text Available This paper is a study on full flute (extra-long tool and ground shank end mill wear analysis by utilizing five-axis CNC to implement flank milling strategy on curved shape part. Five-axis machining eases the user to implement variations of strategy such as flank milling. Flank milling is different from point milling. Point milling cuts materials by using the tip of the tool whereas the flank milling uses the cutting tool body to cut material. The type of cutting tool used was end mill 10 mm diameter with High Speed Steel (HSS material. One factor at a time was utilized to analyze the overall data. Feed rate and spindle speed were the two main factors that been set up equally for both full flute and ground shank end mill. At the end of this research, the qualitative analysis based on tool wear between full flute and ground shank end mill is observed. Generally, both types of cutting tools showed almost the same failure indication such as broken edge or chipped off edge, formation of pinned hole on the surface and serration formation or built-up edge (BUE on the primary flute. However, the results obtained from the enlarged images which were captured by Optical Microscope indicated that, the ground shank end mill is better than the full flute end mill.

Particle deformation during stirred media milling

Science.gov (United States)

Hamey, Rhye Garrett

Production of high aspect ratio metal flakes is an important part of the paint and coating industry. The United States Army also uses high aspect ratio metal flakes of a specific dimension in obscurant clouds to attenuate infrared radiation. The most common method for their production is by milling a metal powder. Ductile metal particles are initially flattened in the process increasing the aspect ratio. As the process continues, coldwelding of metal flakes can take place increasing the particle size and decreasing the aspect ratio. Extended milling times may also result in fracture leading to a further decrease in the particle size and aspect ratio. Both the coldwelding of the particles and the breakage of the particles are ultimately detrimental to the materials performance. This study utilized characterization techniques, such as, light scattering and image analysis to determine the change in particle size as a function of milling time and parameters. This study proved that a fundamental relationship between the milling parameters and particle deformation could be established by using Hertz's theory to calculate the stress acting on the aluminum particles. The study also demonstrated a method by which milling efficiency could be calculated, based on the amount of energy required to cause particle deformation. The study found that the particle deformation process could be an energy efficient process at short milling times with milling efficiency as high as 80%. Finally, statistical design of experiment was used to obtain a model that related particle deformation to milling parameters, such as, rotation rate and milling media size.

Learning Activity Packets for Milling Machines. Unit I--Introduction to Milling Machines.

Science.gov (United States)

Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This learning activity packet (LAP) outlines the study activities and performance tasks covered in a related curriculum guide on milling machines. The course of study in this LAP is intended to help students learn to identify parts and attachments of vertical and horizontal milling machines, identify work-holding devices, state safety rules, and…

Apparatus for drying sugar cubes

NARCIS (Netherlands)

Derckx, H.A.J.; Torringa, H.M.

1999-01-01

Device for drying sugar cubes containing a heating apparatus for heating and dehumidifying the sugar cubes, a conditioning apparatus for cooling off and possibly further dehumidifying the sugar cubes and a conveying apparatus for conveying the sugar cubes through the heating apparatus and the

The Sugar Tax in Holland

NARCIS (Netherlands)

Ajjaji, Fadoua

2016-01-01

This inquiry supports the theory of a sugar tax has a positive influence on the sugar consumption of Dutch individuals. Once a tax is implemented, the sugar consumption declines. Furthermore, this study supported the hypothesis claiming that children have a positive influence on their parental sugar

The Effect of Ultrasonic Waves on Sugar Extraction and Mechanical Properties of Sugar Beet

Directory of Open Access Journals (Sweden)

K Hedayati

2013-09-01

Full Text Available Sugar, which can be extracted from sugar cane and sugar beet, is one of the most important ingredients of food. Conducting more research to increase the extraction efficiency of sugar is necessary due to high production of sugar beet and its numerous processing units in northern Khorasan province. In this research, the effect of temperature, time and the frequency of ultrasonic waves on mechanical properties of sugar beet and its extraction rate of sugar in moisture content of 75% were studied. In this regard, an ultrasonic bath in laboratory scale was used. The studied parameters and their levels were frequency in three levels (zero, 25 and 45 KHz, temperature in three levels (25, 50 and 70 ° C and the imposed time of ultrasonic waves in three levels (10, 20 and 30 min. Samples were prepared using planned experiments and the results were compared with control sugar beet samples. A Saccharimeter was used to measure the concenteration of sugar in samples. Two different types of probe including semi-spherical end and the other one with sharpened edges were used to measure mechanical properties. The studied parameters of frequency, temperature and time showed significant effect on sugar extraction and their resulted effect in optimized levels revealed up to 56% increase in sugar extraction compared with control samples. The obtained values of elastic modulus and shear modulus showed a decreasing trend. The obtained values of total energy of rupture, the total energy of shear, the maximum force of rupture, and the yield point of rupture showed an increasing trend. The frequency had no significant effect on the yield point of rupture and shear force.

Sugar regulation of SUGAR TRANSPORTER PROTEIN 1 (STP1) expression in Arabidopsis thaliana

Science.gov (United States)

Cordoba, Elizabeth; Aceves-Zamudio, Denise Lizeth; Hernández-Bernal, Alma Fabiola; Ramos-Vega, Maricela; León, Patricia

2015-01-01

Sugars regulate the expression of many genes at the transcriptional level. In Arabidopsis thaliana, sugars induce or repress the expression of >1800 genes, including the STP1 (SUGAR TRANSPORTER PROTEIN 1) gene, which encodes an H+/monosaccharide cotransporter. STP1 transcript levels decrease more rapidly after the addition of low concentrations of sugars than the levels of other repressed genes, such as DIN6 (DARK-INDUCED 6). We found that this regulation is exerted at the transcriptional level and is initiated by phosphorylatable sugars. Interestingly, the sugar signal that modulates STP1 expression is transmitted through a HEXOKINASE 1-independent signalling pathway. Finally, analysis of the STP1 5′ regulatory region allowed us to delimit a region of 309bp that contains the cis elements implicated in the glucose regulation of STP1 expression. Putative cis-acting elements involved in this response were identified. PMID:25281700

Sugar - a harmless indulgence?

DEFF Research Database (Denmark)

Rasmussen, Lone Banke; Andersen, Niels Lyhne; Ovesen, L.

1998-01-01

The consumption of sugar is relatively high in Denmark - and other industrial countries - and many persons have a consumption which exceeds the recommended level of maximally 10% of energy intake. A high sugar consumption may reduce the nutrient density of the diet and increase the risk of vitamin...... and mineral deficiency, especially in low energy consumers. The sugar intake and the fat intake, expressed as percentage of energy, usually show an inverse association. This has lead to the statement that a diet with both a low sugar content and a low fat content is incompatible, but we will argue...... that this is not the fact. The significance of sugar for the development of obesity is not clarified. A high fat content in the diet seems to promote the development of obesity, while a high carbohydrate content tends to reduce obesity. It is not known if sugar in this connection is comparable to the other carbohydrates...

Nanocrystalline TiAl powders synthesized by high-energy ball milling: effects of milling parameters on yield and contamination

International Nuclear Information System (INIS)

Bhattacharya, Prajina; Bellon, Pascal; Averback, Robert S.; Hales, Stephen J.

2004-01-01

High-energy ball milling was employed to produce nanocrystalline Ti-Al powders. As sticking of the powders can be sufficiently severe to result in a near zero yield, emphasis was placed on varying milling conditions so as to increase the yield, while avoiding contamination of the powders. The effects of milling parameters such as milling tools, initial state of the powders and addition of process control agents (PCA's) were investigated. Cyclohexane, stearic acid and titanium hydride were used as PCA's. Milling was conducted either in a Cr-steel vial with C-steel balls, or in a tungsten carbide (WC) vial with WC balls, using either elemental or pre-alloyed powders. Powder samples were characterized using X-ray diffraction, scanning and transmission electron microscopy. In the absence of PCA's mechanical alloying in a WC vial and attrition milling in a Cr-steel vial were shown to lead to satisfactory yields, about 65-80%, without inducing any significant contamination of the powders. The results suggest that sticking of the powders on to the milling tools is correlated with the phase evolution occurring in these powders during milling

Surplus electricity production in sugarcane mills using residual bagasse and straw as fuel

International Nuclear Information System (INIS)

Alves, Moises; Ponce, Gustavo H.S.F.; Silva, Maria Aparecida; Ensinas, Adriano V.

2015-01-01

The cogeneration system is one of the most important parts of sugarcane mills which use the bagasse as fuel. In the recent years, modern equipments and energy efficiency measures made possible to the sugarcane industry, the production of surplus electricity which become, besides the sugar and ethanol, a third product from the same renewable source, the sugarcane. This work analyses the surplus electric power systems for three different schemes of cogeneration system in the sugarcane industry through the simulator Thermoflow"®. The analysis is made considering both the available bagasse and sugarcane straw recovery as fuel in three different scenarios for the industrial process energy requirements. The results show that the CEST (Condensing Extraction Steam Turbine) system can have a surplus of electricity of up to four times higher than the BPST (Backpressure Steam Turbine) system. The system CEST can have an increase in surplus power above 23% and 102% for the rate of 10% and 50% of cane straw recovery in the field respectively. The BPST-C (Backpressure and Condensing Turbines) system can produce similar values of surplus electricity when compared with the system CEST, but may represent an opportunity of flexible operation of the cogeneration systems in harvest and off-seasons. - Highlights: • At least three cogeneration system options are available in sugarcane mills. • Nowadays, only steam-based cycle cogeneration systems are used in sugarcane mills. • BPST system is limited to 70 e kWh/t cane of surplus electricity production. • CEST system increases the surplus electricity up to four times than the BPST. • Operation during off-season of the BPST-C system is an advantage for this option.

The progress in the researches for uranium mill tailings cleaning treatment and no-waste uranium ore milling processes

International Nuclear Information System (INIS)

Wang Jintang

1990-01-01

The production of uranium mill tailings and their risk assessment are described. The moethods of uranium mill tailings disposal and management are criticized and the necessity of the researches for uranium mill tailings cleaning treatment and no-wasle uranium ore milling process are demonstrated. The progress for these researches in China and other countries with uranium production is reviewed, and the corresponding conclusions are reported

Energy and water saving measures at the Arloev sugar mill. Final report; Energi- och vattenbesparande aatgaerder vid Arloevs Sockerbruk. Slutrapport

Energy Technology Data Exchange (ETDEWEB)

Wamsler, M. [AAF-Processdesign AB, Malmoe (Sweden)

2001-10-01

The project comprised several, mutually dependent, sub-projects; mapping, investigation of ways to reduce water consumption, membrane tests aiming to find ways to recover sugar, and pinch analysis to evaluate the possibilities for improved process integration. This final report deals with the overall project results. Identified savings opportunities and savings potentials are presented. The presented measures represent an overall optimisation based on the results of all the project parts. Already during the project, measures have been implemented that are calculated to save 65 000 m{sup 3} water annually, corresponding to 10 % of the total water consumption. This saving is in level with the goals for the project. In the table below, these and additional measures are presented with a total savings potential at approximately 200 000 m{sup 3} /year water. The project will then achieve a saving of just below 35 % of present water consumption. Also in the membrane study the results surpassed the expectations. It was found that with nano filtering a sugar concentration of more than 10 %(W) could be reached in the retentate at a flux 50al/m{sup 2}h. The total sugar losses were less than 5 %, i.e. 95 % should be possible to recover. In total, a savings potential of more than 300 tonnes sugar per year is indicated. The Energy savings in the project are calculated to 7,4 GWh/year, of which 0,2 GWh/year by reduced water consumption, 0,6 GWh/year by water recovery, 1,4 GWh/year by membrane technology and 5,2aGWh/year as a result of process integration. This should be compared to the target 2,5 GWh/year. Hence, the results are almost three times the expected. The savings in monetary terms are estimated at just under SEK 5 million per year. The investment is roughly estimated at between SEK 5 and 6 million, of which SEK 4 million for the membrane equipment and SEK 0,5 million for a process water buffer tank. The remaining investment costs cover heat exchangers, control equipment

Start-up of a free water surface constructed wetland for treating olive mill wastewater

Directory of Open Access Journals (Sweden)

Michailides Michail

2015-01-01

Full Text Available An olive mill's existing evaporation pond was separated into five cells and transformed into a free water surface constructed wetland. The constructed wetland was used as a post-treatment stage for olive mill wastewater (OMW. Wastewater was previously treated by an aerobic trickling filter. The influent concentrations in the constructed wetland were 27400 mg.L-1, 4800 mg.L-1, 105 mg.L-1 and 770 mg.L-1 for COD, phenols, ortho-phosphate and TKN, respectively. Despite the rather high influent concentrations, the performance of the constructed wetland was very good since after the 60-day start-up operation period it achieved removal rates of about 94%, 95%, 95% and 98% for COD, phenols, ortho-phosphate and TKN, respectively. The major pollutant removal processes can be attributed to both biological processes occurring in the wetland and photo-oxidation. Laboratory-scale experiments with OMW from fifth cell of the wetland revealed that the net contribution of photo-oxidation after 112 hours of simulated solar radiation at 765 W/m2 (i.e. about 38 days of sunlight irradiation was 18% and 31% removal for COD and phenols, respectively. In the constructed wetland, the total removal reached 81% and 86% for COD and phenols, respectively, for the same time period (38 days.

Evaporation Kinetics of Polyol Droplets: Determination of Evaporation Coefficients and Diffusion Constants

Science.gov (United States)

Su, Yong-Yang; Marsh, Aleksandra; Haddrell, Allen E.; Li, Zhi-Ming; Reid, Jonathan P.

2017-11-01

In order to quantify the kinetics of mass transfer between the gas and condensed phases in aerosol, physicochemical properties of the gas and condensed phases and kinetic parameters (mass/thermal accommodation coefficients) are crucial for estimating mass fluxes over a wide size range from the free molecule to continuum regimes. In this study, we report measurements of the evaporation kinetics of droplets of 1-butanol, ethylene glycol (EG), diethylene glycol (DEG), and glycerol under well-controlled conditions (gas flow rates and temperature) using the previously developed cylindrical electrode electrodynamic balance technique. Measurements are compared with a model that captures the heat and mass transfer occurring at the evaporating droplet surface. The aim of these measurements is to clarify the discrepancy in the reported values of mass accommodation coefficient (αM, equals to evaporation coefficient based on microscopic reversibility) for 1-butanol, EG, and DEG and improve the accuracy of the value of the diffusion coefficient for glycerol in gaseous nitrogen. The uncertainties in the thermophysical and experimental parameters are carefully assessed, the literature values of the vapor pressures of these components are evaluated, and the plausible ranges of the evaporation coefficients for 1-butanol, EG, and DEG as well as uncertainty in diffusion coefficient for glycerol are reported. Results show that αM should be greater than 0.4, 0.2, and 0.4 for EG, DEG, and 1-butanol, respectively. The refined values are helpful for accurate prediction of the evaporation/condensation rates.

75 FR 49524 - Woodland Mills Corporation, Mill Spring, NC; Notice of Affirmative Determination Regarding...

Science.gov (United States)

2010-08-13

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-73,695] Woodland Mills Corporation, Mill Spring, NC; Notice of Affirmative Determination Regarding Application for Reconsideration By application dated July 22, 2010, petitioners requested administrative [[Page 49525

Lake Nasser evaporation reduction study

Directory of Open Access Journals (Sweden)

Hala M.I. Ebaid

2010-10-01

Full Text Available This study aims to evaluate the reduction of evaporation of Lake Nasser’s water caused by disconnecting (fully or partially some of its secondary channels (khors. This evaluation integrates remote sensing, Geographic Information System (GIS techniques, aerodynamic principles, and Landsat7 ETM+ images. Three main procedures were carried out in this study; the first derived the surface temperature from Landsat thermal band; the second derived evaporation depth and approximate evaporation volume for the entire lake, and quantified evaporation loss to the secondary channels’ level over one month (March by applied aerodynamic principles on surface temperature of the raster data; the third procedure applied GIS suitability analysis to determine which of these secondary channels (khors should be disconnected. The results showed evaporation depth ranging from 2.73 mm/day at the middle of the lake to 9.58 mm/day at the edge. The evaporated water-loss value throughout the entire lake was about 0.86 billion m3/month (March. The analysis suggests that it is possible to save an approximate total evaporation volume loss of 19.7 million m3/month (March, and thus 2.4 billion m3/year, by disconnecting two khors with approximate construction heights of 8 m and 15 m. In conclusion, remote sensing and GIS are useful for applications in remote locations where field-based information is not readily available and thus recommended for decision makers remotely planning in water conservation and management.

76 FR 36512 - USDA Increases the Domestic Sugar Overall Allotment Quantity, Reassigns Domestic Cane Sugar...

Science.gov (United States)

2011-06-22

... imports. The OAQ was increased due to an increase in estimated sugar demand since the FY 2011 OAQ was... sugar imports, as required by law. Upon review of the domestic sugarcane processors' sugar marketing allocations relative to their FY 2011 expected raw sugar supplies, CCC determined that all sugarcane...

Black holes with Yang-Mills hair

International Nuclear Information System (INIS)

Kleihaus, B.; Kunz, J.; Sood, A.; Wirschins, M.

1998-01-01

In Einstein-Maxwell theory black holes are uniquely determined by their mass, their charge and their angular momentum. This is no longer true in Einstein-Yang-Mills theory. We discuss sequences of neutral and charged SU(N) Einstein-Yang-Mills black holes, which are static spherically symmetric and asymptotically flat, and which carry Yang-Mills hair. Furthermore, in Einstein-Maxwell theory static black holes are spherically symmetric. We demonstrate that, in contrast, SU(2) Einstein-Yang-Mills theory possesses a sequence of black holes, which are static and only axially symmetric

The evaporative vector: Homogeneous systems

International Nuclear Information System (INIS)

Klots, C.E.

1987-05-01

Molecular beams of van der Waals molecules are the subject of much current research. Among the methods used to form these beams, three-sputtering, laser ablation, and the sonic nozzle expansion of neat gases - yield what are now recognized to be ''warm clusters.'' They contain enough internal energy to undergo a number of first-order processes, in particular that of evaporation. Because of this evaporation and its attendant cooling, the properties of such clusters are time-dependent. The states of matter which can be arrived at via an evaporative vector on a typical laboratory time-scale are discussed. Topics include the (1) temperatures, (2) metastability, (3) phase transitions, (4) kinetic energies of fragmentation, and (5) the expression of magical properties, all for evaporating homogeneous clusters

Pulp mill as an energy producer

International Nuclear Information System (INIS)

Kaulamo, O.

1998-01-01

The recovery boilers of pulp mills are today the most significant producers of wood energy. The power-to-heat ratio of the power plant process, i.e., power yield, is poor in existing applications. In the study, an alternative of improving the power yield of conventional pulp mills significantly was studied by applying solutions used in power plants to a pulp mill. Extensive conversion of wood energy into electricity is possible only in the recovery boiler of the pulp mill and in a large combustion boiler of bark, wood waste and wood chips integrated to this boiler. Hence, the harvest and transports of wood raw materials, i.e. pulp wood and energy wood, are integrated, and the fraction going to cook and the energy wood fraction are separated at the pulp mill. The method guarantees competitive supply of energy wood. As a result a SELLUPOWER mill was designed, where the recovery boiler combusting black liquor and the large power plant boiler combusting energy wood are integrated to one unit and constructed to a power plant process with a high power-to-heat ratio. Necessary technical solutions, project costs and economical feasibility compared to a conventional pulp mill were determined, and the effect of different production-economical parameters was also studied. (orig.)

Colorado's prospectus on uranium milling

International Nuclear Information System (INIS)

Hazle, A.J.; Franz, G.A.; Gamewell, R.

1982-01-01

The first part of this paper will discuss Colorado's control of uranium mill tailings under Titles I and II of the Uranium Mill Tailings Radiation Control Act of 1978. Colorado has a legacy of nine inactive mill sites requiring reclamation under Title I, and two presently active plus a number of new mill proposals which must be regulated in accordance with Title II. Past failures in siting and control on the part of federal jurisdictions have left the state with a heavy legacy requiring extensive effort to address impacts to the state's environment and population. The second part of this paper will discuss the remedial action programme authorized under Public Law 92-314 for Mesa Country, where lack of federal control led to the dispersal of several hundred thousand tons of uranium mill tailings on thousands of properties, including hundreds of homes, schools and other structures. Successful completion of the State efforts under both programmes will depend on a high level of funding and on the maintenance of adequate regulatory standards. (author)

Understanding dental CAD/CAM for restorations - dental milling machines from a mechanical engineering viewpoint. Part A: chairside milling machines.

Science.gov (United States)

Lebon, Nicolas; Tapie, Laurent; Duret, Francois; Attal, Jean-Pierre

2016-01-01

The dental milling machine is an important device in the dental CAD/CAM chain. Nowadays, dental numerical controlled (NC) milling machines are available for dental surgeries (chairside solution). This article provides a mechanical engineering approach to NC milling machines to help dentists understand the involvement of technology in digital dentistry practice. First, some technical concepts and definitions associated with NC milling machines are described from a mechanical engineering viewpoint. The technical and economic criteria of four chairside dental NC milling machines that are available on the market are then described. The technical criteria are focused on the capacities of the embedded technologies of these milling machines to mill both prosthetic materials and types of shape restorations. The economic criteria are focused on investment costs and interoperability with third-party software. The clinical relevance of the technology is assessed in terms of the accuracy and integrity of the restoration.

Measurements of the evaporation rate upon evaporation of thin layer at different heating modes

OpenAIRE

Gatapova E.Ya.; Korbanova E.G.

2017-01-01

Technique for measurements of the evaporation rate of a heated liquid layer is presented. The local minimum is observed which is associated with the point of equilibrium of the liquid–gas interface. It is shown when no heat is applied to the heating element temperature in gas phase is larger than in liquid, and evaporation occurs with the rate of 0.014–0.018 μl/s. Then evaporation rate is decreasing with increasing the heater temperature until the equilibrium point is reached at the liquid–ga...

John Stuart Mill: utilitarismo e liberalismo = John Stuart Mill: utilitarianism and liberalism

Directory of Open Access Journals (Sweden)

Simões, Mauro Cardoso

2013-01-01

Full Text Available Meu objetivo, neste trabalho, é investigar a compatibilidade das teses utilitaristas e liberais de John Stuart Mill. Apresentarei, inicialmente, os principais críticos da filosofia moral e política de Mill, para os quais o discípulo de Bentham teria abandonado o utilitarismo ou, ainda, não esclarecido suficientemente seu princípio da liberdade, o que o tornaria um pensador assistemático e inconsistente. Minha tese é contrária a tais interpretações, uma vez que sustenta ser Mill consistente. Em seguida, defenderei uma interpretação do princípio da liberdade e da individualidade, procurando demonstrar que seu utilitarismo é compatível com seu liberalismo

Odor control in evaporation ponds treating olive mill wastewater through the use of Ca(OH)2.

Science.gov (United States)

Lagoudianaki, E; Manios, T; Geniatakis, M; Frantzeskaki, N; Manios, V

2003-01-01

Different amounts of Ca(OH)2 were added in 2 L beakers containing 1 L of olive mill wastewater (OMW). The mixture was stirred for 45 min and left to settle. Wastewater analysis was used in order to determine the effect of the different amounts of calcium hydroxide in the treating process, three days after the application. The Odor Detection Threshold was used for determining the effect of the treatment in the odors produced in the beakers, three and 30 days after. Both sets of measurements indicated an important reduction in wastewater pollutants and odor emission when 10 g/L of Ca(OH)2 were added. In order to evaluate these results in more realistic conditions. 10 L plastic containers were filled with 6 L of OMW, relevant amounts of Ca(OH)2 were added, the mixture was stirred manually and left to settle in the open. Again, 10 g/L of calcium hydroxide produced the best results in odor reduction and wastewater treatment.

Combined pretreatment with hot compressed water and wet disk milling opened up oil palm biomass structure resulting in enhanced enzymatic digestibility.

Science.gov (United States)

Zakaria, Mohd Rafein; Hirata, Satoshi; Fujimoto, Shinji; Hassan, Mohd Ali

2015-10-01

Combined pretreatment with hot compressed water and wet disk milling was performed with the aim to reduce the natural recalcitrance of oil palm biomass by opening its structure and provide maximal access to cellulase attack. Oil palm empty fruit bunch and oil palm frond fiber were first hydrothermally pretreated at 150-190° C and 10-240 min. Further treatment with wet disk milling resulted in nanofibrillation of fiber which caused the loosening of the tight biomass structure, thus increasing the subsequent enzymatic conversion of cellulose to glucose. The effectiveness of the combined pretreatments was evaluated by chemical composition changes, power consumption, morphological alterations by SEM and the enzymatic digestibility of treated samples. At optimal pretreatment process, approximately 88.5% and 100.0% of total sugar yields were obtained from oil palm empty fruit bunch and oil palm frond fiber samples, which only consumed about 15.1 and 23.5 MJ/kg of biomass, respectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

Evaporation-triggered microdroplet nucleation and the four life phases of an evaporating Ouzo droplet

NARCIS (Netherlands)

Tan, H.; Diddens, C.; Lv, P.; Kuerten, J.G.M.; Zhang, X.; Lohse, D.

2016-01-01

Evaporating liquid droplets are omnipresent in nature and technology, such as in inkjet printing, coating, deposition of materials, medical diagnostics, agriculture, the food industry, cosmetics, or spills of liquids. Whereas the evaporation of pure liquids, liquids with dispersed particles, or even

Evaporation-triggered microdroplet nucleation and the four life phases of an evaporating Ouzo drop

NARCIS (Netherlands)

Tan, Huanshu; Diddens, Christian; Lv, Pengyu; Kuerten, J.G.M.; Zhang, Xuehua; Lohse, Detlef

2016-01-01

Evaporating liquid droplets are omnipresent in nature and technology, such as in inkjet printing, coating, deposition of materials, medical diagnostics, agriculture, the food industry, cosmetics, or spills of liquids. Whereas the evaporation of pure liquids, liquids with dispersed particles, or even

75 FR 53013 - Fiscal Year 2011 Tariff-rate Quota Allocations for Raw Cane Sugar, Refined and Specialty Sugar...

Science.gov (United States)

2010-08-30

... for Raw Cane Sugar, Refined and Specialty Sugar, and Sugar-containing Products; Revision AGENCY... August 17, 2010 concerning Fiscal Year 2011 tariff-rate quota allocations of raw cane sugar, refined and special sugar, and sugar-containing products. USTR is revising the effective date of that notice to...

Worldwide trends in dietary sugars intake.

Science.gov (United States)

Wittekind, Anna; Walton, Janette

2014-12-01

Estimating trends in dietary intake data is integral to informing national nutrition policy and monitoring progress towards dietary guidelines. Dietary intake of sugars is a controversial public health issue and guidance in relation to recommended intakes is particularly inconsistent. Published data relating to trends in sugars intake are relatively sparse. The purpose of the present review was to collate and review data from national nutrition surveys to examine changes and trends in dietary sugars intake. Only thirteen countries (all in the developed world) appear to report estimates of sugars intake from national nutrition surveys at more than one point in time. Definitions of dietary sugars that were used include 'total sugars', 'non-milk extrinsic sugars', 'added sugars', sucrose' and 'mono- and disaccharides'. This variability in terminology across countries meant that comparisons were limited to within countries. Hence trends in dietary sugars intake were examined by country for the whole population (where data permitted), and for specific or combined age and sex subpopulations. Findings indicate that in the majority of population comparisons, estimated dietary sugars intake is either stable or decreasing in both absolute (g/d) and relative (% energy) terms. An increase in sugars intake was observed in few countries and only in specific subpopulations. In conclusion, the findings from the present review suggest that, in the main, dietary sugars intake are decreasing or stable. A consistent approach to estimation of dietary sugars intake from national nutrition surveys is required if more valid estimates of changes in dietary sugars intakes are required in the future.

Optimization of FIB milling for rapid NEMS prototyping

DEFF Research Database (Denmark)

Malm, Bjarke; Petersen, Dirch Hjorth; Lei, Anders

2011-01-01

We demonstrate an optimized milling technique to focused ion beam (FIB) milling in template silicon membranes for fast prototyping of nanoelectromechanical systems (NEMS). Using a single-pass milling strategy the highly topology dependent sputtering rate is boosted and shorter milling time...... is achieved. Drift independence is obtained for small critical features using a radial scan strategy, and a back scan routine ensures minimal line width deviation removing redeposited material. Milling a design similar to a nano four-point probe with a pitch down to 400nm we display what optimized FIB milling...

Yang-Mills theory for non-semisimple groups

CERN Document Server

Nuyts, J; Nuyts, Jean; Wu, Tai Tsun

2003-01-01

For semisimple groups, possibly multiplied by U(1)'s, the number of Yang-Mills gauge fields is equal to the number of generators of the group. In this paper, it is shown that, for non-semisimple groups, the number of Yang-Mills fields can be larger. These additional Yang-Mills fields are not irrelevant because they appear in the gauge transformations of the original Yang-Mills fields. Such non-semisimple Yang-Mills theories may lead to physical consequences worth studying. The non-semisimple group with only two generators that do not commute is studied in detail.

242-A evaporator hazards assessment

International Nuclear Information System (INIS)

Johnson, T.L.

1998-01-01

This document establishes the technical basis in support of Emergency Planning activities for the 242-A Evaporator, on the Hanford Site. Through this document the technical basis for the development of facility specific Emergency Action Levels and the Emergency Planning Zone is demonstrated. The evaporator sues a conventional, forced-circulation, vacuum evaporation system to concentrate radioactive waste solutions. This concentration results in the reduction in waste volume and reduces the number of double-shelled tanks required to store the waste

Chevron's Panna Maria mill process description

International Nuclear Information System (INIS)

Anon.

1979-01-01

Key features of Chevron's Uranium Mill located near Panna Maria, Texas, are described. The mill is designed to process a nominal 2500 dry tons/day of uranium bearing ore containing 15% uncombined moisture. The following operations at the mill are highlighted: ore receiving, grinding, leaching, countercurrent decantation and tailings disposal, filtering, solvent extraction, solvent stripping, precipitation, drying, and packaging

Drop evaporation and triple line dynamics

Science.gov (United States)

Sobac, Benjamin; Brutin, David; Gavillet, Jerome; Université de Provence Team; Cea Liten Team

2011-03-01

Sessile drop evaporation is a phenomenon commonly came across in nature or in industry with cooling, paintings or DNA mapping. However, the evaporation of a drop deposited on a substrate is not completely understood due to the complexity of the problem. Here we investigate, with several nano-coating of the substrate (PTFE, SiOx, SiOc and CF), the influence of the dynamic of the triple line on the evaporation process. The experiment consists in analyzing simultaneously the motion of the triple line, the kinetics of evaporation, the internal thermal motion and the heat and mass transfer. Measurements of temperature, heat-flux and visualizations with visible and infrared cameras are performed. The dynamics of the evaporative heat flux appears clearly different depending of the motion of the triple line

Methods for dehydration of sugars and sugar alcohols

Science.gov (United States)

Holladay, Johnathan E [Kennewick, WA; Hu, Jianli [Kennewick, WA; Zhang, Xinjie [Burlington, MA; Wang, Yong [Richland, WA

2010-08-10

The invention includes a method of dehydration of a sugar using a dehydration catalyst and a co-catalyst within a reactor. A sugar is introduced and H.sub.2 is flowed through the reactor at a pressure of less than or equal to about 300 psig to convert at least some of the sugar into an anhydrosugar product. The invention includes a process for producing isosorbide. A starting material comprising sorbitol is flowed into a reactor. H.sub.2 is counter flowed through the reactor. The starting material is exposed to a catalyst in the presence of a co-catalyst which comprises at least one metal. The exposing is conducted at a hydrogen pressure of less than or equal to 300 psig within the reactor and the hydrogen removes at least some of any water present during the exposing and inhibits formation of colored byproducts.

Trends in evaporation of a large subtropical lake

Science.gov (United States)

Hu, Cheng; Wang, Yongwei; Wang, Wei; Liu, Shoudong; Piao, Meihua; Xiao, Wei; Lee, Xuhui

2017-07-01

How rising temperature and changing solar radiation affect evaporation of natural water bodies remains poor understood. In this study, evaporation from Lake Taihu, a large (area 2400 km2) freshwater lake in the Yangtze River Delta, China, was simulated by the CLM4-LISSS offline lake model and estimated with pan evaporation data. Both methods were calibrated against lake evaporation measured directly with eddy covariance in 2012. Results show a significant increasing trend of annual lake evaporation from 1979 to 2013, at a rate of 29.6 mm decade-1 according to the lake model and 25.4 mm decade-1 according to the pan method. The mean annual evaporation during this period shows good agreement between these two methods (977 mm according to the model and 1007 mm according to the pan method). A stepwise linear regression reveals that downward shortwave radiation was the most significant contributor to the modeled evaporation trend, while air temperature was the most significant contributor to the pan evaporation trend. Wind speed had little impact on the modeled lake evaporation but had a negative contribution to the pan evaporation trend offsetting some of the temperature effect. Reference evaporation was not a good proxy for the lake evaporation because it was on average 20.6 % too high and its increasing trend was too large (56.5 mm decade-1).

Galilean Yang-Mills theory

Energy Technology Data Exchange (ETDEWEB)

Bagchi, Arjun [Center for Theoretical Physics, Massachusetts Institute of Technology,77 Massachusetts Avenue, Cambridge, MA 02139 (United States); Basu, Rudranil [Saha Institute of Nuclear Physics,Block AF, Sector 1, Bidhannagar, Kolkata 700068 (India); Kakkar, Ashish [Indian Institute of Science Education and Research,Dr Homi Bhabha Road, Pashan. Pune 411008 (India); Mehra, Aditya [Indian Institute of Science Education and Research,Dr Homi Bhabha Road, Pashan. Pune 411008 (India); Van Swinderen Institute for Particle Physics and Gravity, University of Groningen, Nijenborgh 4, 9747 AG Groningen (Netherlands)

2016-04-11

We investigate the symmetry structure of the non-relativistic limit of Yang-Mills theories. Generalising previous results in the Galilean limit of electrodynamics, we discover that for Yang-Mills theories there are a variety of limits inside the Galilean regime. We first explicitly work with the SU(2) theory and then generalise to SU(N) for all N, systematising our notation and analysis. We discover that the whole family of limits lead to different sectors of Galilean Yang-Mills theories and the equations of motion in each sector exhibit hitherto undiscovered infinite dimensional symmetries, viz. infinite Galilean Conformal symmetries in D=4. These provide the first examples of interacting Galilean Conformal Field Theories (GCFTs) in D>2.

Galilean Yang-Mills theory

International Nuclear Information System (INIS)

Bagchi, Arjun; Basu, Rudranil; Kakkar, Ashish; Mehra, Aditya

2016-01-01

We investigate the symmetry structure of the non-relativistic limit of Yang-Mills theories. Generalising previous results in the Galilean limit of electrodynamics, we discover that for Yang-Mills theories there are a variety of limits inside the Galilean regime. We first explicitly work with the SU(2) theory and then generalise to SU(N) for all N, systematising our notation and analysis. We discover that the whole family of limits lead to different sectors of Galilean Yang-Mills theories and the equations of motion in each sector exhibit hitherto undiscovered infinite dimensional symmetries, viz. infinite Galilean Conformal symmetries in D=4. These provide the first examples of interacting Galilean Conformal Field Theories (GCFTs) in D>2.

New models for droplet heating and evaporation

KAUST Repository

Sazhin, Sergei S.

2013-02-01

A brief summary of new models for droplet heating and evaporation, developed mainly at the Sir Harry Ricardo Laboratory of the University of Brighton during 2011-2012, is presented. These are hydrodynamic models for mono-component droplet heating and evaporation, taking into account the effects of the moving boundary due to evaporation, hydrodynamic models of multi-component droplet heating and evaporation, taking and not taking into account the effects of the moving boundary, new kinetic models of mono-component droplet heating and evaporation, and a model for mono-component droplet evaporation, based on molecular dynamics simulation. The results, predicted by the new models are compared with experimental data and the prehctions of the previously developed models where possible. © 2013 Asian Network for Scientific Information.

Evaporation, Boiling and Bubbles

Science.gov (United States)

Goodwin, Alan

2012-01-01

Evaporation and boiling are both terms applied to the change of a liquid to the vapour/gaseous state. This article argues that it is the formation of bubbles of vapour within the liquid that most clearly differentiates boiling from evaporation although only a minority of chemistry textbooks seems to mention bubble formation in this context. The…

Texture formation in iron particles using mechanical milling with graphite as a milling aid

Energy Technology Data Exchange (ETDEWEB)

Motozuka, S.; Hayashi, K. [Department of Mechanical Engineering, Gifu National College of Technology, 2236-2 Kamimakuwa, Motosu, Gifu 501-0495 (Japan); Tagaya, M. [Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka, Niigata 940-2188 (Japan); Morinaga, M. [Toyota Physical and Chemical Research Institute, 41-1, Yokomichi, Nagakute, Aichi 480-1192 (Japan)

2015-09-15

Crystallographically anisotropic platelet iron particles were successfully prepared using a conventional ball mill with addition of graphite (Gp) particles. The morphological and structural changes resulting from the milling were investigated using scanning electron microscopy and X-ray diffraction. The spherical iron particles were plastically deformed into platelet shapes during the milling. Simultaneously, it is suggested that the size of the Gp particles decreased and adhered as nanoparticles on the surface of the iron particles. The adhered Gp particles affected the plastic deformation behavior of the iron particles: the (001) planes of α-iron were oriented parallel to the particle face, and no preferred in-plane orientation was observed. This study not only details the preparation of soft magnetic metal particles that crystallographically oriented to enhance their magnetic properties but also provides new insight into the activities of the well-established and extensively studied mechanical milling method.

Texture formation in iron particles using mechanical milling with graphite as a milling aid

International Nuclear Information System (INIS)

Motozuka, S.; Hayashi, K.; Tagaya, M.; Morinaga, M.

2015-01-01

Crystallographically anisotropic platelet iron particles were successfully prepared using a conventional ball mill with addition of graphite (Gp) particles. The morphological and structural changes resulting from the milling were investigated using scanning electron microscopy and X-ray diffraction. The spherical iron particles were plastically deformed into platelet shapes during the milling. Simultaneously, it is suggested that the size of the Gp particles decreased and adhered as nanoparticles on the surface of the iron particles. The adhered Gp particles affected the plastic deformation behavior of the iron particles: the (001) planes of α-iron were oriented parallel to the particle face, and no preferred in-plane orientation was observed. This study not only details the preparation of soft magnetic metal particles that crystallographically oriented to enhance their magnetic properties but also provides new insight into the activities of the well-established and extensively studied mechanical milling method

Ambient aerosol concentrations of sugars and sugar-alcohols at four different sites in Norway

Directory of Open Access Journals (Sweden)

K. E. Yttri

2007-08-01

Full Text Available Sugars and sugar-alcohols are demonstrated to be important constituents of the ambient aerosol water-soluble organic carbon fraction, and to be tracers for primary biological aerosol particles (PBAP. In the present study, levels of four sugars (fructose, glucose, sucrose, trehalose and three sugar-alcohols (arabitol, inositol, mannitol in ambient aerosols have been quantified using a novel HPLC/HRMS-TOF (High Performance Liquid Chromatography in combination with High Resolution Mass Spectrometry – Time of Flight method to assess the contribution of PBAP to PM>sub>10 and PM_2.5. Samples were collected at four sites in Norway at different times of the year in order to reflect the various contributing sources and the spatial and seasonal variation of the selected compounds.

Sugars and sugar-alcohols were present at all sites investigated, underlining the ubiquity of these highly polar organic compounds. The highest concentrations were reported for sucrose, reaching a maximum concentration of 320 ng m⁻³ in PM₁₀ and 55 ng m⁻³ in PM_2.5. The mean concentration of sucrose was up to 10 times higher than fructose, glucose and the dimeric sugar trehalose. The mean concentrations of the sugar-alcohols were typically lower, or equal, to that of the monomeric sugars and trehalose. Peak concentrations of arabitol and mannitol did not exceed 30 ng m⁻³ in PM₁₀, and for PM_2.5 all concentrations were below 6 ng m⁻³.

Sugars and sugar-alcohols were associated primarily with coarse aerosols except during wintertime at the suburban site in Elverum, where a shift towards sub micron aerosols was observed. It is proposed that this shift was due to the intensive use of wood burning for residential heating at this site during winter, confirmed by high concurrent concentrations of levoglucosan. Elevated concentrations of sugars in PM₂

Treatment of liquid radioactive waste: Evaporation

International Nuclear Information System (INIS)

Pfeiffer, R.

1982-01-01

About 10.000 m 3 of low active liquid waste (LLW) arise in the Nuclear Research Center Karlsruhe. Chemical contents of this liquid waste are generally not declared. Resulting from experiments carried out in the Center during the early sixties, the evaporator facility was built in 1968 for decontamination of LLW. The evaporators use vapor compression and concentrate recirculation in the evaporator sump by pumps. Since 1971 the medium active liquid waste (MLW) from the Karlsruhe Reprocessing Plant (WAK) was decontaminated in this evaporator facility, too. By this time the amount of low liquid waste (LLW) had been decontaminated without mentionable interruptions. Afterwards a lot of interruptions of operations occurred, mainly due to leakages of pumps, valves and pipes. There was also a very high radiation level for the operating personnel. As a consequence of this experience a new evaporator facility for decontamination of medium active liquid waste was built in 1974. This facility started operation in 1976. The evaporator has natural circulation and is heated by steam through a heat exchanger. (orig./RW)

Relationships between soluble sugar concentrations in roots and ecosystem stress for first-year sugar maple seedlings

Energy Technology Data Exchange (ETDEWEB)

McLaughlin, J.W.; Reed, D.D.; Jurgensen, M.F.; Mroz, G.D.; Bagley, S.T. [Michigan Technological University, Houghton, MI (United States). School of Forestry and Wood Products

1996-03-01

Accumulation of reducing sugars (i.e. glucose and fructose) in plant roots has been consistently correlated with forest dieback and decline and, therefore, has potential as a biological indicator of ecosystem stress. In this study, the relationships between acidic deposition and `natural` (temperature, mycorrhizae, and nutrition) factors with first-year sugar maple seedling root sugar concentrations and growth were assessed in two sugar maple dominated forests in Michigan. Seedlings at the southern site (Wellston) had greater root growth, phosphorus, total sugar, and sucrose concentrations in roots, but lower reducing sugar concentration in roots. In addition, percent root length colonized by vesicular-arbuscular mycorrhizal fungi was less than that found for seedlings growing at the northern site (Alberta). Throughfall deposition of nitrate, sulfate, and hydrogen ions was not significantly correlated with seedling total or reducing sugar concentration. Total sugar concentration in seedling roots was positively correlated with air and soil temperatures at the southern site, but not at the northern site. Seedling tissue phosphorus concentration was correlated with total sugars at both sites, with sucrose at the southern site, and reducing sugars at the northern site. Mycorrhizal colonization rates at the Alberta site were positively correlated with reducing sugar concentration in seedling roots and negatively correlated with sucrose concentration. The results suggest that differences in seedling root sugar concentrations in these two forests are related to seedling root growth and are most likely due to ecological variables, such as available soil phosphorus, temperature, and growing season length through some complex interaction with mycorrhizae rather than acidic deposition stress. 56 refs., 3 figs.

Metoder for Modellering, Simulering og Regulering af Større Termiske Processer anvendt i Sukkerproduktion. Methods for Modelling, Simulation and Control of Large Scale Thermal Systems Applied in Sugar Production

DEFF Research Database (Denmark)

Nielsen, Kirsten Mølgaard; Nielsen, Jens Frederik Dalsgaard

The subject of this Ph.D. thesis is to investigate and develop methods for modelling, simulation and control applicable in large scale termal industrial plants. An ambition has been to evaluate the results in a physical process. Sugar production is well suited for the purpose. In collaboration...... simulator has been developed. The simulator handles the normal working conditions relevant to control engineers. A non-linear dynamic model based on mass and energy balances has been developed. The model parameters have been adjusted to data measured on a Danish sugar plant. The simulator consists...... of a computer, a data terminal and an electric interface corresponding to the interface at the sugar plant. The simulator is operating in realtime and thus a realistic test of controllers is possible. The idiomatic control methodology has been investigated developing a control concept for the evaporation...

Life Cycle Assessment of Sugar Production (VB)

DEFF Research Database (Denmark)

Teljigovic, Mehmed; Mengiardi, Jon; Factor, Gabriela

1999-01-01

The environmental organisation NOAH has proposed carrying out an environmental assessment of two different sugar productions (using sugar beet or sugar cane) in order to illustrate which of the systems has a higher environmental impact for sugar consumption in Denmark. Therefore a comparison...... will be made between sugar from sugar beet produced in Denmark versus sugar produces from sugar cane in a tropical country, Brazil, and transported afterwards to Denmark. To evaluate the environmental aspects of these two product systems a Life Cycle Assessement (LCA) will be carried out.From the results...... obtained in the present LCA of sugar produces from sugar canes or sugar beet it is difficult to make an immediate choice between the two possibilities. Indeed, Quantitative results from the EDIP (Environmental Design of Industrial Products) software are globally similar for both ways of producing sugar...

The evaporation of crude oil and petroleum products

International Nuclear Information System (INIS)

Fingas, M. F.

1996-01-01

The physics of oil and petroleum evaporation was studied by means of an experimental apparatus. The evaporation was determined by weight loss and recorded on a computer. Examination of the data showed that most oil and petroleum products (those with seven to ten components) evaporate at a logarithmic rate with respect to time, while other petroleum products (those with fewer chemical components) evaporate at a rate which is square root with respect to time. Evaporation of oil and petroleum was not strictly boundary-layer regulated because the typical oil evaporation rate rates do not exceed that of molecular diffusion and thus turbulent diffusion does not increase the evaporation rates. Overall, boundary layer regulation can be ignored in the prediction of oil and petroleum evaporation. The simple equation relating only the logarithm of time (or the square root of time in the case of narrow-cut products) and temperature are sufficient to accurately describe oil evaporation. refs., figs

Water evaporation: a transition path sampling study.

Science.gov (United States)

Varilly, Patrick; Chandler, David

2013-02-07

We use transition path sampling to study evaporation in the SPC/E model of liquid water. On the basis of thousands of evaporation trajectories, we characterize the members of the transition state ensemble (TSE), which exhibit a liquid-vapor interface with predominantly negative mean curvature at the site of evaporation. We also find that after evaporation is complete, the distributions of translational and angular momenta of the evaporated water are Maxwellian with a temperature equal to that of the liquid. To characterize the evaporation trajectories in their entirety, we find that it suffices to project them onto just two coordinates: the distance of the evaporating molecule to the instantaneous liquid-vapor interface and the velocity of the water along the average interface normal. In this projected space, we find that the TSE is well-captured by a simple model of ballistic escape from a deep potential well, with no additional barrier to evaporation beyond the cohesive strength of the liquid. Equivalently, they are consistent with a near-unity probability for a water molecule impinging upon a liquid droplet to condense. These results agree with previous simulations and with some, but not all, recent experiments.

Modeling Evaporation and Particle Assembly in Colloidal Droplets.

Science.gov (United States)

Zhao, Mingfei; Yong, Xin

2017-06-13

Evaporation-induced assembly of nanoparticles in a drying droplet is of great importance in many engineering applications, including printing, coating, and thin film processing. The investigation of particle dynamics in evaporating droplets can provide fundamental hydrodynamic insight for revealing the processing-structure relationship in the particle self-organization induced by solvent evaporation. We develop a free-energy-based multiphase lattice Boltzmann method coupled with Brownian dynamics to simulate evaporating colloidal droplets on solid substrates with specified wetting properties. The influence of interface-bound nanoparticles on the surface tension and evaporation of a flat liquid-vapor interface is first quantified. The results indicate that the particles at the interface reduce surface tension and enhance evaporation flux. For evaporating particle-covered droplets on substrates with different wetting properties, we characterize the increase of evaporate rate via measuring droplet volume. We find that droplet evaporation is determined by the number density and circumferential distribution of interfacial particles. We further correlate particle dynamics and assembly to the evaporation-induced convection in the bulk and on the surface of droplet. Finally, we observe distinct final deposits from evaporating colloidal droplets with bulk-dispersed and interface-bound particles. In addition, the deposit pattern is also influenced by the equilibrium contact angle of droplet.

Evaporation From Soil Containers With Irregular Shapes

Science.gov (United States)

Assouline, Shmuel; Narkis, Kfir

2017-11-01

Evaporation from bare soils under laboratory conditions is generally studied using containers of regular shapes where the vertical edges are parallel to the flow lines in the drying domain. The main objective of this study was to investigate the impact of irregular container shapes, for which the flow lines either converge or diverge toward the surface. Evaporation from initially saturated sand and sandy loam soils packed in cones and inverted cones was compared to evaporation from corresponding cylindrical columns. The initial evaporation rate was higher in the cones, and close to potential evaporation. At the end of the experiment, the cumulative evaporation depth in the sand cone was equal to that in the column but higher than in the inverted cone, while in the sandy loam, the order was cone > column > inverted cone. By comparison to the column, stage 1 evaporation was longer in the cones, and practically similar in the inverted cones. Stage 2 evaporation rate decreased with the increase of the evaporating surface area. These results were more pronounced in the sandy loam. For the sand column, the transition between stage 1 and stage 2 evaporation occurred when the depth of the saturation front was approximately equal to the characteristic length of the soil. However, for the cone and the inverted cone, it occurred for a shallower depth of the saturation front. It seems therefore that the concept of the characteristic length derived from the soil hydraulic properties is related to drying systems of regular shapes.

Evaporative lithographic patterning of binary colloidal films.

Science.gov (United States)

Harris, Daniel J; Conrad, Jacinta C; Lewis, Jennifer A

2009-12-28

Evaporative lithography offers a promising new route for patterning a broad array of soft materials. In this approach, a mask is placed above a drying film to create regions of free and hindered evaporation, which drive fluid convection and entrained particles to regions of highest evaporative flux. We show that binary colloidal films exhibit remarkable pattern formation when subjected to a periodic evaporative landscape during drying.

Evaporative cooling in polymer electrolyte fuel cell

Energy Technology Data Exchange (ETDEWEB)

Shimotori, S; Sonai, A [Toshiba Corp. Tokyo (Japan)

1996-06-05

The concept of the evaporative cooling for the internally humidified PEFC was confirmed by the experiment. The evaporative cooling rates at the anode and the cathode were mastered under the various temperatures and air utilizations. At a high temperature the proportion of the evaporative cooling rate to the heat generation rate got higher, the possibility of the evaporative cooling was demonstrated. 2 refs., 7 figs., 1 tab.

Intrinsic Evaporative Cooling by Hygroscopic Earth Materials

Directory of Open Access Journals (Sweden)

Alexandra R. Rempel

2016-08-01

Full Text Available The phase change of water from liquid to vapor is one of the most energy-intensive physical processes in nature, giving it immense potential for cooling. Diverse evaporative cooling strategies have resulted worldwide, including roof ponds and sprinklers, courtyard fountains, wind catchers with qanats, irrigated green roofs, and fan-assisted evaporative coolers. These methods all require water in bulk liquid form. The evaporation of moisture that has been sorbed from the atmosphere by hygroscopic materials is equally energy-intensive, however, yet has not been examined for its cooling potential. In arid and semi-arid climates, hygroscopic earth buildings occur widely and are known to maintain comfortable indoor temperatures, but evaporation of moisture from their walls and roofs has been regarded as unimportant since water scarcity limits irrigation and rainfall; instead, their cool interiors are attributed to well-established mass effects in delaying the transmission of sensible gains. Here, we investigate the cooling accomplished by daily cycles of moisture sorption and evaporation which, requiring only ambient humidity, we designate as “intrinsic” evaporative cooling. Connecting recent soil science to heat and moisture transport studies in building materials, we use soils, adobe, cob, unfired earth bricks, rammed earth, and limestone to reveal the effects of numerous parameters (temperature and relative humidity, material orientation, thickness, moisture retention properties, vapor diffusion resistance, and liquid transport properties on the magnitude of intrinsic evaporative cooling and the stabilization of indoor relative humidity. We further synthesize these effects into concrete design guidance. Together, these results show that earth buildings in diverse climates have significant potential to cool themselves evaporatively through sorption of moisture from humid night air and evaporation during the following day’s heat. This finding

Towards a rational definition of potential evaporation

Directory of Open Access Journals (Sweden)

J.-P. Lhommel

1997-01-01

Full Text Available The concept of potential evaporation is defined on the basis of the following criteria: (i it must establish an upper limit to the evaporation process in a given environment (the term 'environment' including meteorological and surface conditions, and (ii this upper limit must be readily calculated from measured input data. It is shown that this upper limit is perfectly defined and is given by the Penman equation, applied with the corresponding meteorological data (incoming radiation and air characteristics measured at a reference height and the appropriate surface characteristics (albedo, roughness length, soil heat flux. Since each surface has its own potential evaporation, a function of its own surface characteristics, it is useful to define a reference potential evaporation as a short green grass completely shading the ground. Although the potential evaporation from a given surface is readily calculated from the Penman equation, its physical significance or interpretation is not so straightforward, because it represents only an idealized situation, not a real one. Potential evaporation is the evaporation from this surface, when saturated and extensive enough to obviate any effect of local advection, under the same meteorological conditions. Due to the feedback effects of evaporation on air characteristics, it does not represent the 'real' evaporation (i.e. the evaporation which could be physically observed in the real world from such an extensive saturated surface in these given meteorological conditions (if this saturated surface were substituted for an unsaturated one previously existing. From a rigorous standpoint, this calculated potential evaporation is not physically observable. Nevertheless, an approximate representation can be given by the evaporation from a limited saturated area, the dimension of which depends on the height of measurement of the air characteristics used as input in the Penman equation. If they are taken at a height

Modelling refrigerant distribution in microchannel evaporators

DEFF Research Database (Denmark)

Brix, Wiebke; Kærn, Martin Ryhl; Elmegaard, Brian

2009-01-01

of the refrigerant distribution is carried out for two channels in parallel and for two different cases. In the first case maldistribution of the inlet quality into the channels is considered, and in the second case a non-uniform airflow on the secondary side is considered. In both cases the total mixed superheat...... out of the evaporator is kept constant. It is shown that the cooling capacity of the evaporator is reduced significantly, both in the case of unevenly distributed inlet quality and for the case of non-uniform airflow on the outside of the channels.......The effects of refrigerant maldistribution in parallel evaporator channels on the heat exchanger performance are investigated numerically. For this purpose a 1D steady state model of refrigerant R134a evaporating in a microchannel tube is built and validated against other evaporator models. A study...

Current uranium mill licensing issues

International Nuclear Information System (INIS)

Scarano, R.A.

1977-01-01

The problems encountered to insure environmentally safe mining and milling of uranium ores are reviewed. Emphasis is placed on the management of tailings resulting from milling operations. It is pointed out that although the concentration of radioactivity in the tailings is relatively low, control measures are necessary because of the large quantities involved and because of the long half-life of the parent radionuclides present. The major concerns with mill tailings are radon release to the atmosphere and isolation of the tailings from the human environment. Since it is anticipated that the amount of tailings created by the year 2000 will be more than an order of magnitude greater than the quantities that have been generated during the past 30 years, it is recommended that all mill tailings storage areas be located remote from public contact and in areas such that disruption and dispersion by natural forces and seepage of toxic materials into ground water systems are reduced to the maximum extent achievable. Technical issues that receive attention during the NRC licensing process for uranium mills and the preparation of environmental impact statements are discussed briefly

Biofuel manufacturing from woody biomass: effects of sieve size used in biomass size reduction.

Science.gov (United States)

Zhang, Meng; Song, Xiaoxu; Deines, T W; Pei, Z J; Wang, Donghai

2012-01-01

Size reduction is the first step for manufacturing biofuels from woody biomass. It is usually performed using milling machines and the particle size is controlled by the size of the sieve installed on a milling machine. There are reported studies about the effects of sieve size on energy consumption in milling of woody biomass. These studies show that energy consumption increased dramatically as sieve size became smaller. However, in these studies, the sugar yield (proportional to biofuel yield) in hydrolysis of the milled woody biomass was not measured. The lack of comprehensive studies about the effects of sieve size on energy consumption in biomass milling and sugar yield in hydrolysis process makes it difficult to decide which sieve size should be selected in order to minimize the energy consumption in size reduction and maximize the sugar yield in hydrolysis. The purpose of this paper is to fill this gap in the literature. In this paper, knife milling of poplar wood was conducted using sieves of three sizes (1, 2, and 4 mm). Results show that, as sieve size increased, energy consumption in knife milling decreased and sugar yield in hydrolysis increased in the tested range of particle sizes.

Is evaporative colling important for shallow clouds?

Science.gov (United States)

Gentine, P.; Park, S. B.; Davini, P.; D'Andrea, F.

2017-12-01

We here investigate and test using large-eddy simulations the hypothesis that evaporative cooling might not be crucial for shallow clouds. Results from various Shallow convection and stratocumulus LES experiments show that the influence of evaporative cooling is secondary compared to turbulent mixing, which dominates the buoyancy reversal. In shallow cumulus subising shells are not due to evaporative cooling but rather reflect a vortical structure, with a postive buoyancy anomaly in the core due to condensation. Disabling evaporative cooling has negligible impact on this vortical structure and on buoyancy reversal. Similarly in non-precipitating stratocumuli evaporative cooling is negeligible copmared to other factors, especially turbulent mixing and pressure effects. These results emphasize that it may not be critical to icnlude evaporative cooling in parameterizations of shallow clouds and that it does not alter entrainment.

Would John Stuart Mill have regulated pornography?

OpenAIRE

McGlynn, C.; Ward, I.

2014-01-01

John Stuart Mill dominates contemporary pornography debates where he is routinely invoked as an authoritative defence against regulation. This article, by contrast, argues that a broader understanding of Mill's ethical liberalism, his utilitarianism, and his feminism casts doubt over such an assumption. New insights into Mill's approach to sex, sexual activity, and the regulation of prostitution reveal an altogether more nuanced and activist approach. We conclude that John Stuart Mill would a...

Experimental and kinetics study for phytoremediation of sugar mill effluent using water lettuce (Pistia stratiotes L.) and its end use for biogas production.

Science.gov (United States)

Kumar, Vinod; Singh, Jogendra; Pathak, V V; Ahmad, Shamshad; Kothari, Richa

2017-10-01

In present study, the performance of phytoremediation by Pistia stratiotes on sugar mill effluent (SME) and its end use for biogas production are investigated. The objectives of the study are to determine the nutrient and pollution reduction efficiency of P. stratiotes from SME and evaluation of its biomass as a feedstock for biogas production. Various concentrations of SME (25, 50, 75, and 100%) were remediated by Pistia stratiotes (initial weight; 150 g) outdoor for 60 days under batch mode experimental setup. The results showed that P. stratiotes achieved marked reduction in nutrient (TKN, 72.86%; TP, 71.49%) and pollutant load (EC, 25.69%; TDS, 57.26%; BOD, 69.40%; COD, 61.80%; Ca 2+ , 56.79%; Mg 2+ , 55.01%; Na + , 42.86%; K + , 54.38%; MPN, 78.13%; SPC, 60.13%) from 75% SME at the end of the experiment. The highest biomass (328.48 ± 2.04 g) and chlorophyll content (3.62 ± 3.04 mg/g) were also achieved with 75% SME. The dried biomass of P. stratiotes (from 75% SME) was inoculated with cow dung (10% w/v) and diluted with distilled water (1:10). The whole content was used as a substrate for the biogas production within hydraulic retention time (HRT) of 30 days at room temperature. Substrate parameters such as pH, TS (%), COD (mg/L), TKN (%), TOC (%), VS (%), and C/N ratio were reduced from 7.85 to 6.0, 66.65 to 28.65%, 12,900 to 2800 mg/L, 0.95 to 0.75%, 45.54 to 19.5%, 76.87 to 28.78%, and 47.94 to 26.00, respectively, in 30 days of HRT. About 8478.6 mL of cumulative biogas production was evaluated by modified Gompertz equation. Thus, the present investigation not only achieved efficient nutrient and pollution reduction from SME but also proved the potential of P. stratiotes for biogas production.

A trial of sugar-free or sugar-sweetened beverages and body weight in children

NARCIS (Netherlands)

de Ruyter, Janne C; Olthof, Margreet R; Seidell, Jacob C; Katan, Martijn B

2012-01-01

BACKGROUND: The consumption of beverages that contain sugar is associated with overweight, possibly because liquid sugars do not lead to a sense of satiety, so the consumption of other foods is not reduced. However, data are lacking to show that the replacement of sugar-containing beverages with

Improving milling and production of a dust-producing unit equipped with hammer mills

Energy Technology Data Exchange (ETDEWEB)

Vorotnikov, Ye.G.; Nikiforov, A.A.; Rasputin, O.V.; Sukhunin, V.I.

1982-01-01

This paper presents generalized experience for deriving coarse ground coal dust in hammer mills by providing comparison data on improving efficiency of operation of the unit when switching to a coarser-type grind of the fuel. Need to have more precise formulas to calculate grinding potential of hammer mills when using a coarser grind is shown.

Wear of micro end mills

DEFF Research Database (Denmark)

Bissacco, Giuliano; Hansen, Hans Nørgaard; De Chiffre, Leonardo

2005-01-01

This paper addresses the important issue of wear on micro end mills considering relevant metrological tools for its characterization and quantification. Investigation of wear on micro end mills is particularly difficult and no data are available in the literature. Small worn volumes cause large...... part. For this investigation 200 microns end mills are considered. Visual inspection of the micro tools requires high magnification and depth of focus. 3D reconstruction based on scanning electron microscope (SEM) images and stereo-pair technique is foreseen as a possible method for quantification...

Process integration study of a kraft pulp mill converted to an ethanol production plant – Part A: Potential for heat integration of thermal separation units

International Nuclear Information System (INIS)

Fornell, Rickard; Berntsson, Thore

2012-01-01

Energy efficiency is an important parameter for the profitability of biochemical ethanol production from lignocellulosic raw material. The yield of ethanol is generally low due to the limited amount of fermentable compounds in the raw material. Increasing energy efficiency leads to possibilities of exporting more by-products, which in turn might reduce the net production cost of ethanol. Energy efficiency is also an important issue when discussing the repurposing of kraft pulp mills to biorefineries, since the mills in question most likely will be old and inefficient. Investing in energy efficiency measures might therefore have a large effect on the economic performance. This paper discusses energy efficiency issues related to the repurposing of a kraft pulp mill into a lignocellulosic ethanol production plant. The studied process is a typical Scandinavian kraft pulp mill that has been converted to a biorefinery with ethanol as main product. A process integration study, using pinch analysis and process simulations, has been performed in order to assess alternative measures for improving the energy efficiency. The improvements found have also been related to the possibilities for by-product sales from the plant (electricity and/or lignin). In a forthcoming paper, which is the second part of this process integration study, an economic analysis based on the results from this paper will be presented. - Highlights: ► Conversion of a kraft pulp mill to ethanol production. ► Heat integration of distillation/evaporation in a lignocellulosic ethanol plant. ► Advanced pinch curves used to find new integration possibilities. ► 35–40% reduction of steam demand.

Dual manifold heat pipe evaporator

Science.gov (United States)

Adkins, D.R.; Rawlinson, K.S.

1994-01-04

An improved evaporator section is described for a dual manifold heat pipe. Both the upper and lower manifolds can have surfaces exposed to the heat source which evaporate the working fluid. The tubes in the tube bank between the manifolds have openings in their lower extensions into the lower manifold to provide for the transport of evaporated working fluid from the lower manifold into the tubes and from there on into the upper manifold and on to the condenser portion of the heat pipe. A wick structure lining the inner walls of the evaporator tubes extends into both the upper and lower manifolds. At least some of the tubes also have overflow tubes contained within them to carry condensed working fluid from the upper manifold to pass to the lower without spilling down the inside walls of the tubes. 1 figure.

Evaporation from a sphagnum moss surface

Science.gov (United States)

D.S. Nichols; J.M. Brown

1980-01-01

Peat cores, 45 cm in diameter, were collected from a sphagnum bog in northern Minnesota, and used to measure the effects of different temperatures and water levels on evaporation from a sphagnum moss surface in a growth chamber. Under all conditions, evaporation from the moss surface was greater than that from a free-water surface. Evaporation from the moss increased...

Ball-milling-induced crystallization and ball-milling effect on thermal crystallization kinetics in an amorphous FeMoSiB alloy

International Nuclear Information System (INIS)

Guo, F.Q.; Lu, K.

1997-01-01

Microstructure evolution in a melt-spun amorphous Fe 77.2 Mo 0.8 Si 9 B 13 alloy subjected to high-energy ball milling was investigated by means of X-ray diffraction (XRD), a transmission electron microscope (TEM), and a differential scanning calorimeter (DSC). It was found that during ball milling, crystallization occurs in the amorphous ribbon sample with precipitation of an α-Fe solid solution, and the amorphous sample crystallizes completely into a single α-Fe nanostructure (rather than α-Fe and borides as in the usual thermal crystallization products) when the milling time exceeds 135 hours. The volume fraction of material crystallized was found to be approximately proportional to the milling time. The fully crystallized sample with a single α-Fe nanophase exhibits an intrinsic thermal stability against phase separation upon annealing at high temperatures. The ball-milling effect on the subsequent thermal crystallization of the amorphous phase in an as-milled sample was studied by comparison of the crystallization products and kinetic parameters between the as-quenched amorphous sample and the as-milled sample was studied by comparison of the crystallization products and kinetic parameters between the as-quenched amorphous sample and the as-milled partially crystallized samples. The crystallization temperatures and activation energies for the crystallization processes of the residual amorphous phase were considerably decreased due to ball milling, indicating that ball milling has a significant effect on the depression of thermal stability of the residual amorphous phase

Effects of milling on functional properties of rice flour.

Science.gov (United States)

Kadan, R S; Bryant, R J; Miller, J A

2008-05-01

A commercial long-grain rice flour (CRF) and the flours made by using a pin mill and the Udy mill from the same batch of broken second-head white long-grain rice were evaluated for their particle size and functional properties. The purpose of this study was to compare the commercial rice flour milling method to the pin and Udy milling methods used in our laboratory and pilot plant. The results showed that pin milled flour had more uniform particle size than the other 2 milled flours. The chalky kernels found in broken white milled rice were pulverized more into fines in both Udy milled flour and CRF than in the pin milled flour. The excessive amount of fines in flours affected their functional properties, for example, WSI and their potential usage in the novel foods such as rice breads (RB). The RB made from CRF collapsed more than loaves made from pin milled Cypress long-grain flours.

Sugar holograms with erioglaucine and tartrazine

Science.gov (United States)

Mejias-Brizuela, N. Y.; Olivares-Pérez, A.; Páez-Trujillo, G.; Fuentes-Tapia, I.

2007-09-01

An artificial green colorant, composed by erioglaucine (Blue 1) and tartrazine (Yellow 5), was employed in a sugar matrix to improve the material sensibility and to make a comparative analysis of the diffraction efficiency parameter, for holograms replications, the holographic pattern was obtained by a computer and recorded in sugar films and in modified sugar (sugar-colorant). Conventional lithography and UV radiation were used. The results show that the behavior diffraction efficiency of the sugar-colorant films is slightly larger than in the sugar matrix under the same recording conditions.

77 FR 14837 - Bioassay at Uranium Mills

Science.gov (United States)

2012-03-13

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0057] Bioassay at Uranium Mills AGENCY: Nuclear Regulatory..., ``Bioassay at Uranium Mills.'' This guide describes a bioassay program acceptable to the NRC staff for uranium mills and applicable portions of uranium conversion facilities where the possibility of exposure...

Transcription Factor AREB2 Is Involved in Soluble Sugar Accumulation by Activating Sugar Transporter and Amylase Genes.

Science.gov (United States)

Ma, Qi-Jun; Sun, Mei-Hong; Lu, Jing; Liu, Ya-Jing; Hu, Da-Gang; Hao, Yu-Jin

2017-08-01

Sugars play important roles in plant growth and development, crop yield and quality, as well as responses to abiotic stresses. Abscisic acid (ABA) is a multifunctional hormone. However, the exact mechanism by which ABA regulates sugar accumulation is largely unknown in plants. Here, we tested the expression profile of several sugar transporter and amylase genes in response to ABA treatment. MdSUT2 and MdAREB2 were isolated and genetically transformed into apple ( Malus domestica ) to investigate their roles in ABA-induced sugar accumulation. The MdAREB2 transcription factor was found to bind to the promoters of the sugar transporter and amylase genes and activate their expression. Both MdAREB2 and MdSUT2 transgenic plants produced more soluble sugars than controls. Furthermore, MdAREB2 promoted the accumulation of sucrose and soluble sugars in an MdSUT2 -dependent manner. Our results demonstrate that the ABA-responsive transcription factor MdAREB2 directly activates the expression of amylase and sugar transporter genes to promote soluble sugar accumulation, suggesting a mechanism by which ABA regulates sugar accumulation in plants. © 2017 American Society of Plant Biologists. All Rights Reserved.

Soil Carbon 4 per mille

Science.gov (United States)

Minasny, Budiman; van Wesemael, Bas

2017-04-01

The '4 per mille Soils for Food Security and Climate' was launched at the COP21 aiming to increase global soil organic matter stocks by 4 per mille (or 0.4 %) per year as a compensation for the global emissions of greenhouse gases by anthropogenic sources. This paper surveyed the soil organic carbon (SOC) stock estimates and sequestration potentials from 20 regions in the world (New Zealand, Chile, South Africa, Australia, Tanzania, Indonesia, Kenya, Nigeria, India, China Taiwan, South Korea, China Mainland, United States of America, France, Canada, Belgium, England & Wales, Ireland, Scotland, and Russia) and asked whether the 4 per mille initiative is feasible. This study highlights region specific efforts and scopes for soil carbon sequestration. Reported soil C sequestration rates generally show that under best management practices, 4 per mille or even higher sequestration rates can be accomplished. High C sequestration rates (up to 10 per mille) can be achieved for soils with low initial SOC stock (topsoil less than 30 t C ha-1), and at the first twenty years after implementation of best management practices. In addition, areas that have reached equilibrium but not at their saturation level will not be able to further increase their sequestration. We found that most studies on SOC sequestration globally only consider topsoil (up to 0.3 m depth), as it is considered to be most affected by management techniques. The 4 per mille initiative was based on a blanket calculation of the whole global soil profile C stock, however the potential to increase SOC is mostly on managed agricultural lands. If we consider 4 per mille on global topsoil of agricultural land, SOC sequestration is about 3.6 Gt C per year, which effectively offset 40% of global anthropogenic greenhouse gas emissions. As a strategy for climate change mitigation, soil carbon sequestration buys time over the next ten to twenty years while other effective sequestration and low carbon technologies become

40 CFR 61.142 - Standard for asbestos mills.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Standard for asbestos mills. 61.142... § 61.142 Standard for asbestos mills. (a) Each owner or operator of an asbestos mill shall either discharge no visible emissions to the outside air from that asbestos mill, including fugitive sources, or...

New models for droplet heating and evaporation

KAUST Repository

Sazhin, Sergei S.; Elwardani, Ahmed Elsaid; Gusev, Ivan G.; Xie, Jianfei; Shishkova, Irina N.; Cao, Bingyang; Snegirev, Alexander Yu.; Heikal, Morgan Raymond

2013-01-01

and evaporation, taking into account the effects of the moving boundary due to evaporation, hydrodynamic models of multi-component droplet heating and evaporation, taking and not taking into account the effects of the moving boundary, new kinetic models of mono

KEPLER PLANETS: A TALE OF EVAPORATION

International Nuclear Information System (INIS)

Owen, James E.; Wu, Yanqin

2013-01-01

Inspired by the Kepler mission's planet discoveries, we consider the thermal contraction of planets close to their parent star, under the influence of evaporation. The mass-loss rates are based on hydrodynamic models of evaporation that include both X-ray and EUV irradiation. We find that only low mass planets with hydrogen envelopes are significantly affected by evaporation, with evaporation being able to remove massive hydrogen envelopes inward of ∼0.1 AU for Neptune-mass objects, while evaporation is negligible for Jupiter-mass objects. Moreover, most of the evaporation occurs in the first 100 Myr of stars' lives when they are more chromospherically active. We construct a theoretical population of planets with varying core masses, envelope masses, orbital separations, and stellar spectral types, and compare this population with the sizes and densities measured for low-mass planets, both in the Kepler mission and from radial velocity surveys. This exercise leads us to conclude that evaporation is the driving force of evolution for close-in Kepler planets. In fact, some 50% of the Kepler planet candidates may have been significantly eroded. Evaporation explains two striking correlations observed in these objects: a lack of large radius/low density planets close to the stars and a possible bimodal distribution in planet sizes with a deficit of planets around 2 R ⊕ . Planets that have experienced high X-ray exposures are generally smaller than this size, and those with lower X-ray exposures are typically larger. A bimodal planet size distribution is naturally predicted by the evaporation model, where, depending on their X-ray exposure, close-in planets can either hold on to hydrogen envelopes ∼0.5%-1% in mass or be stripped entirely. To quantitatively reproduce the observed features, we argue that not only do low-mass Kepler planets need to be made of rocky cores surrounded with hydrogen envelopes, but few of them should have initial masses above 20 M ⊕ and

KEPLER PLANETS: A TALE OF EVAPORATION

Energy Technology Data Exchange (ETDEWEB)

Owen, James E. [Canadian Institute for Theoretical Astrophysics, 60 St. George Street, Toronto, ON M5S 3H8 (Canada); Wu, Yanqin, E-mail: jowen@cita.utoronto.ca, E-mail: wu@astro.utoronto.ca [Department of Astronomy and Astrophysics, University of Toronto, Toronto, ON M5S 3H4 (Canada)

2013-10-01

Inspired by the Kepler mission's planet discoveries, we consider the thermal contraction of planets close to their parent star, under the influence of evaporation. The mass-loss rates are based on hydrodynamic models of evaporation that include both X-ray and EUV irradiation. We find that only low mass planets with hydrogen envelopes are significantly affected by evaporation, with evaporation being able to remove massive hydrogen envelopes inward of ∼0.1 AU for Neptune-mass objects, while evaporation is negligible for Jupiter-mass objects. Moreover, most of the evaporation occurs in the first 100 Myr of stars' lives when they are more chromospherically active. We construct a theoretical population of planets with varying core masses, envelope masses, orbital separations, and stellar spectral types, and compare this population with the sizes and densities measured for low-mass planets, both in the Kepler mission and from radial velocity surveys. This exercise leads us to conclude that evaporation is the driving force of evolution for close-in Kepler planets. In fact, some 50% of the Kepler planet candidates may have been significantly eroded. Evaporation explains two striking correlations observed in these objects: a lack of large radius/low density planets close to the stars and a possible bimodal distribution in planet sizes with a deficit of planets around 2 R{sub ⊕}. Planets that have experienced high X-ray exposures are generally smaller than this size, and those with lower X-ray exposures are typically larger. A bimodal planet size distribution is naturally predicted by the evaporation model, where, depending on their X-ray exposure, close-in planets can either hold on to hydrogen envelopes ∼0.5%-1% in mass or be stripped entirely. To quantitatively reproduce the observed features, we argue that not only do low-mass Kepler planets need to be made of rocky cores surrounded with hydrogen envelopes, but few of them should have initial masses above

Declining consumption of added sugars and sugar-sweetened beverages in Australia: a challenge for obesity prevention.

Science.gov (United States)

Brand-Miller, Jennie C; Barclay, Alan W

2017-04-01

Background: Reduced intakes of added sugars and sugar-sweetened beverages (SSBs) have been the main focus of efforts to stall obesity. Although obesity has risen steeply in Australia, some evidence suggests that added-sugars and SSB intakes have declined over the same time frame. Objective: We investigated recent trends in the availability of sugars and sweeteners and changes in intakes of total sugars, added sugars, and SSBs in Australia by using multiple, independent data sources. Design: The study was designed to compare relevant data published by the Food and Agriculture Organization of the United Nations [FAO Statistics Division Database (FAOSTAT)], the Australian government, academia, and the food industry. Results: With the use of the FAOSTAT food balance sheets for Australia, the per capita availability of added or refined sugars and sweeteners was shown to have fallen 16% from 152 g/d in 1980 to 127 g/d in 2011 ( P -trend = 0.001). In national dietary surveys in 1995 and 2011-2012, added-sugars intake declined markedly in adult men (from 72 to 59 g/d; -18%) but not in women (44-42 g/d; NS). As a proportion of total energy, added-sugars intake fell 10% in adult men but nonsignificantly in adult women. Between 1995 and 2011-2012, the proportion of energy from SSBs (including 100% juice) declined 10% in adult men and 20% in women. More marked changes were observed in children aged 2-18 y. Data from national grocery sales indicated that per capita added-sugars intakes derived from carbonated soft drinks fell 26% between 1997 and 2011 (from 23 to 17 g/d) with similar trends for noncarbonated beverages. Conclusions: In Australia, 4 independent data sets confirmed shorter- and longer-term declines in the availability and intake of added sugars, including those contributed by SSBs. The findings challenge the widespread belief that energy from added sugars or sugars in solution are uniquely linked to the prevalence of obesity. © 2017 American Society for Nutrition.

Carbohydrates, Sugar, and Your Child

Science.gov (United States)

... carbs are: simple carbohydrates (or simple sugars): including fructose, glucose, and lactose, which also are found in nutritious ... sugar, check the ingredients list for sugar, corn syrup, or other sweeteners, such as dextrose, fructose, honey, or molasses, to name just a few. ...

Exploring Ultimate Water Capillary Evaporation in Nanoscale Conduits.

Science.gov (United States)

Li, Yinxiao; Alibakhshi, Mohammad Amin; Zhao, Yihong; Duan, Chuanhua

2017-08-09

Capillary evaporation in nanoscale conduits is an efficient heat/mass transfer strategy that has been widely utilized by both nature and mankind. Despite its broad impact, the ultimate transport limits of capillary evaporation in nanoscale conduits, governed by the evaporation/condensation kinetics at the liquid-vapor interface, have remained poorly understood. Here we report experimental study of the kinetic limits of water capillary evaporation in two dimensional nanochannels using a novel hybrid channel design. Our results show that the kinetic-limited evaporation fluxes break down the limits predicated by the classical Hertz-Knudsen equation by an order of magnitude, reaching values up to 37.5 mm/s with corresponding heat fluxes up to 8500 W/cm 2 . The measured evaporation flux increases with decreasing channel height and relative humidity but decreases as the channel temperature decreases. Our findings have implications for further understanding evaporation at the nanoscale and developing capillary evaporation-based technologies for both energy- and bio-related applications.

Increased release of fermentable sugars from elephant grass by enzymatic hydrolysis in the presence of surfactants

International Nuclear Information System (INIS)

Menegol, Daiane; Scholl, Angélica Luisi; Fontana, Roselei Claudete; Dillon, Aldo José Pinheiro; Camassola, Marli

2014-01-01

Highlights: • Milling is an attractive method to enhance the enzymatic hydrolysis of biomass. • Surfactants improve the efficiency of lignocellulose enzymatic hydrolysis. • Pretreatment with NaOH, smaller particle size and Tween 80® were more efficient. - Abstract: In the search for renewable energy sources, elephant grass is an alternative substrate for ethanol production, but this substrate must be hydrolyzed by cellulases and xylanases to liberate fermentable sugars. During enzymatic hydrolysis, cellulase activity is reduced by the irreversible adsorption of cellulase onto cellulose, decreasing the rate of hydrolysis. Adding surfactants during hydrolysis can improve the process. The effects of Tween® and Triton® surfactants on the enzymatic hydrolysis of elephant grass were evaluated in this context. The data indicate that pretreatment with sodium hydroxide, along with a smaller particle size (0.075–0.152 mm) and the use of Tween 80®, increased the efficiency of releasing reducing sugars from pretreated elephant grass biomass. Thus, it is possible to reduce grinding costs in second-generation ethanol production through the use of surfactants, as they allow efficient hydrolysis of larger biomass particles

75 FR 22095 - USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2010 Raw Sugar Tariff...

Science.gov (United States)

2010-04-27

... USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2010 Raw Sugar Tariff-Rate... announced a reassignment of surplus sugar under domestic cane sugar allotments of 200,000 short tons raw value (STRV) to imports, and increased the fiscal year (FY) 2010 raw sugar tariff-rate quota (TRQ) by...

75 FR 38764 - USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2010 Raw Sugar Tariff...

Science.gov (United States)

2010-07-06

... USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2010 Raw Sugar Tariff-Rate... announced a reassignment of surplus sugar under domestic cane sugar allotments of 300,000 short tons raw value (STRV) to imports, and increased the fiscal year (FY) 2010 raw sugar tariff-rate quota (TRQ) by...

76 FR 20305 - USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2011 Raw Sugar Tariff...

Science.gov (United States)

2011-04-12

... USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2011 Raw Sugar Tariff-Rate... announced a reassignment of surplus sugar under domestic cane sugar allotments of 325,000 short tons raw value (STRV) to imports, and increased the fiscal year (FY) 2011 raw sugar tariff-rate quota (TRQ) by...

Dynamics of sugar-metabolic enzymes and sugars accumulation during watermelon (citrullus lanatus) fruit development

International Nuclear Information System (INIS)

Zhang, H.

2016-01-01

We analyzed sugar accumulation and the activities of sugar-metabolic enzymes in ripening fruits of three cultivars of watermelon; a high-sugar type w2, a low-sugar type (w1), and their hybrid. In w2, the glucose and fructose contents were higher than the sucrose content in the earlier stage of fruit development, and fruit growth was accompanied by increases in glucose, fructose, and sucrose contents. The sucrose content increased substantially after 20 days after anthesis (DAA) and it was the main soluble sugar in mature fruit (sucrose: hexoses ratio, 0.71). In W, the fructose and glucose contents were significantly higher than the sucrose content in mature fruit (sucrose: hexoses ratio, 0.25). Comparing the two parent cultivars, sucrose was the most important factor affecting the total sugar content in mature fruit, although glucose and fructose also contributed to total sugar contents. The fructose and glucose contents in the fruit of F1 were mid-way between those of their parents, while the sucrose content was closer to that of W (sucrose:hexoses ratio in F1, 0.26). In the early stage of fruit development of W2, the activities of acid invertase and neutral invertase were higher than those of sucrose synthase and sucrose phosphate synthase. After 20 DAA, the acid invertase and neutral invertase activities decreased and those of sucrose synthase and sucrose phosphate synthase increased, leading to increased sucrose content. In W1, the activities of acid invertase and neutral invertase were higher than those of sucrose synthase and sucrose phosphate synthase at the early stage. The sucrose synthase and sucrose phosphate synthase activities were lower in W1 than in W2 at the later stages of fruit development. The patterns of sugar accumulation and sugar-metabolic enzyme activities during fruit development in F1 were similar to those in W1. (author)

Evaporation of Particle-Stabilized Emulsion Sunscreen Films.

Science.gov (United States)

Binks, Bernard P; Fletcher, Paul D I; Johnson, Andrew J; Marinopoulos, Ioannis; Crowther, Jonathan M; Thompson, Michael A

2016-08-24

We recently showed (Binks et al., ACS Appl. Mater. Interfaces, 2016, DOI: 10.1021/acsami.6b02696) how evaporation of sunscreen films consisting of solutions of molecular UV filters leads to loss of UV light absorption and derived sun protection factor (SPF). In the present work, we investigate evaporation-induced effects for sunscreen films consisting of particle-stabilized emulsions containing a dissolved UV filter. The emulsions contained either droplets of propylene glycol (PG) in squalane (SQ), droplets of SQ in PG or droplets of decane in PG. In these different emulsion types, the SQ is involatile and shows no evaporation, the PG is volatile and evaporates relatively slowly, whereas the decane is relatively very volatile and evaporates quickly. We have measured the film mass and area, optical micrographs of the film structure, and the UV absorbance spectra during evaporation. For emulsion films containing the involatile SQ, evaporation of the PG causes collapse of the emulsion structure with some loss of specular UV absorbance due to light scattering. However, for these emulsions with droplets much larger than the wavelength of light, the light is scattered only at small forward angles so does not contribute to the diffuse absorbance and the film SPF. The UV filter remains soluble throughout the evaporation and thus the UV absorption by the filter and the SPF remain approximately constant. Both PG-in-SQ and SQ-in-PG films behave similarly and do not show area shrinkage by dewetting. In contrast, the decane-in-PG film shows rapid evaporative loss of the decane, followed by slower loss of the PG resulting in precipitation of the UV filter and film area shrinkage by dewetting which cause the UV absorbance and derived SPF to decrease. Measured UV spectra during evaporation are in reasonable agreement with spectra calculated using models discussed here.

Comparative anatomy of the peduncles of Thai Sugar Palms provides insight on putative sugar transport mechanisms

DEFF Research Database (Denmark)

Somjaiai, Pananun; Barfod, Anders; Jampeetong, Arunothai

Inflorescences of sugar palms exude copious amounts of sugar-rich sap, when their peduncles are scarred. In Thailand this phenomenon form the basis of a widespread cottage industry based on species such as Arenga pinnata, Borassus flabellifera, Cocos nucifera and Nypa fruticans. The extracted sugar...... sap is used mainly for jaggery, syrup and different types of beverages. In this study we looked for anatomical correlates of the elevated sap flow in injured peduncles of sugar palms. Despite a limited sample size we observed that sugar producing palms differ from the reference palm Chamaedorea...

Water evaporation in silica colloidal deposits.

Science.gov (United States)

Peixinho, Jorge; Lefèvre, Grégory; Coudert, François-Xavier; Hurisse, Olivier

2013-10-15

The results of an experimental study on the evaporation and boiling of water confined in the pores of deposits made of mono-dispersed silica colloidal micro-spheres are reported. The deposits are studied using scanning electron microscopy, adsorption of nitrogen, and adsorption of water through attenuated total reflection-infrared spectroscopy. The evaporation is characterized using differential scanning calorimetry and thermal gravimetric analysis. Optical microscopy is used to observe the patterns on the deposits after evaporation. When heating at a constant rate and above boiling temperature, the release of water out of the deposits is a two step process. The first step is due to the evaporation and boiling of the surrounding and bulk water and the second is due to the desorption of water from the pores. Additional experiments on the evaporation of water from membranes having cylindrical pores and of heptane from silica deposits suggest that the second step is due to the morphology of the deposits. Copyright © 2013 Elsevier Inc. All rights reserved.

Controlling water evaporation through self-assembly.

Science.gov (United States)

Roger, Kevin; Liebi, Marianne; Heimdal, Jimmy; Pham, Quoc Dat; Sparr, Emma

2016-09-13

Water evaporation concerns all land-living organisms, as ambient air is dryer than their corresponding equilibrium humidity. Contrarily to plants, mammals are covered with a skin that not only hinders evaporation but also maintains its rate at a nearly constant value, independently of air humidity. Here, we show that simple amphiphiles/water systems reproduce this behavior, which suggests a common underlying mechanism originating from responding self-assembly structures. The composition and structure gradients arising from the evaporation process were characterized using optical microscopy, infrared microscopy, and small-angle X-ray scattering. We observed a thin and dry outer phase that responds to changes in air humidity by increasing its thickness as the air becomes dryer, which decreases its permeability to water, thus counterbalancing the increase in the evaporation driving force. This thin and dry outer phase therefore shields the systems from humidity variations. Such a feedback loop achieves a homeostatic regulation of water evaporation.

Sugar in Infants, Children and Adolescents

DEFF Research Database (Denmark)

Mis, Nataša Fidler; Braegger, Christian; Bronsky, Jiri

2017-01-01

The consumption of sugars, particularly sugar-sweetened beverages (SSBs; beverages or drinks that contain added caloric sweeteners (i.e. sucrose, high-fructose corn syrup, fruit-juice concentrates), in European children and adolescents exceeds current recommendations. This is of concern because...... there is no nutritional requirement for free sugars, and infants have an innate preference for sweet taste, which may be modified and reinforced by pre- and postnatal exposures. Sugar containing beverages/free sugars increase the risk for overweight/obesity and dental caries, can result in poor nutrient supply...... and reduced dietary diversity and may be associated with increased risk of type 2 diabetes mellitus, cardiovascular risk, and other health effects. The term 'free sugars', includes all monosaccharides/disaccharides added to foods/beverages by the manufacturer/cook/consumer, plus sugars naturally present...

Sugar in infants, children and adolescents

DEFF Research Database (Denmark)

Mis, Nataša Fidler; Braegger, Christian; Bronsky, Jiri

2017-01-01

The consumption of sugars, particularly sugar-sweetened beverages (SSBs; beverages or drinks that contain added caloric sweeteners (i.e. sucrose, high-fructose corn syrup, fruit-juice concentrates), in European children and adolescents exceeds current recommendations. This is of concern because...... there is no nutritional requirement for free sugars, and infants have an innate preference for sweet taste, which may be modified and reinforced by pre- and postnatal exposures. Sugar containing beverages/free sugars increase the risk for overweight/obesity and dental caries, can result in poor nutrient supply...... and reduced dietary diversity and may be associated with increased risk of type 2 diabetes mellitus, cardiovascular risk, and other health effects. The term 'free sugars', includes all monosaccharides/disaccharides added to foods/beverages by the manufacturer/cook/consumer, plus sugars naturally present...

Waste Feed Evaporation Physical Properties Modeling

International Nuclear Information System (INIS)

Daniel, W.E.

2003-01-01

This document describes the waste feed evaporator modeling work done in the Waste Feed Evaporation and Physical Properties Modeling test specification and in support of the Hanford River Protection Project (RPP) Waste Treatment Plant (WTP) project. A private database (ZEOLITE) was developed and used in this work in order to include the behavior of aluminosilicates such a NAS-gel in the OLI/ESP simulations, in addition to the development of the mathematical models. Mathematical models were developed that describe certain physical properties in the Hanford RPP-WTP waste feed evaporator process (FEP). In particular, models were developed for the feed stream to the first ultra-filtration step characterizing its heat capacity, thermal conductivity, and viscosity, as well as the density of the evaporator contents. The scope of the task was expanded to include the volume reduction factor across the waste feed evaporator (total evaporator feed volume/evaporator bottoms volume). All the physical properties were modeled as functions of the waste feed composition, temperature, and the high level waste recycle volumetric flow rate relative to that of the waste feed. The goal for the mathematical models was to predict the physical property to predicted simulation value. The simulation model approximating the FEP process used to develop the correlations was relatively complex, and not possible to duplicate within the scope of the bench scale evaporation experiments. Therefore, simulants were made of 13 design points (a subset of the points used in the model fits) using the compositions of the ultra-filtration feed streams as predicted by the simulation model. The chemistry and physical properties of the supernate (the modeled stream) as predicted by the simulation were compared with the analytical results of experimental simulant work as a method of validating the simulation software

Spray and evaporation characteristics of ethanol and gasoline direct injection in non-evaporating, transition and flash-boiling conditions

International Nuclear Information System (INIS)

Huang, Yuhan; Huang, Sheng; Huang, Ronghua; Hong, Guang

2016-01-01

Highlights: • Sprays can be considered as non-evaporating when vapour pressure is lower than 30 kPa. • Ethanol direct injection should only be applied in high temperature engine environment. • Gasoline spray collapses at lower fuel temperature (350 K) than ethanol spray does (360 K). • Flash-boiling does not occur when fuel temperature reaches boiling point until ΔT is 14 K. • Not only spray evaporation mode but also breakup mechanism change with fuel temperature. - Abstract: Ethanol direct injection plus gasoline port injection (EDI + GPI) represents a more efficient and flexible way to utilize ethanol fuel in spark ignition engines. To exploit the potentials of EDI, the mixture formation characteristics need to be investigated. In this study, the spray and evaporation characteristics of ethanol and gasoline fuels injected from a multi-hole injector were investigated by high speed Shadowgraphy imaging technique in a constant volume chamber. The experiments covered a wide range of fuel temperature from 275 K (non-evaporating) to 400 K (flash-boiling) which corresponded to cold start and running conditions in an engine. The spray transition process from normal-evaporating to flash-boiling was investigated in greater details than the existed studies. Results showed that ethanol and gasoline sprays demonstrated the same patterns in non-evaporating conditions. The sprays could be considered as non-evaporating when vapour pressure was lower than 30 kPa. Ethanol evaporated more slowly than gasoline did in low temperature environment, but they reached the similar evaporation rates when temperature was higher than 375 K. This suggested that EDI should only be applied in high temperature engine environment. For both ethanol and gasoline sprays, when the excess temperature was smaller than 4 K, the sprays behaved the same as the subcooled sprays did. The sprays collapsed when the excess temperature was 9 K. Flash-boiling did not occur until the excess temperature

Yang-Mills theory in Coulomb gauge; Yang-Mills-theorie in Coulombeichung

Energy Technology Data Exchange (ETDEWEB)

Feuchter, C.

2006-07-01

In this thesis we study the Yang-Mills vacuum structure by using the functional Schroedinger picture in Coulomb gauge. In particular we discuss the scenario of colour confinement, which was originally formulated by Gribov. After a short introduction, we recall some basic aspects of Yang-Mills theories, its canonical quantization in the Weyl gauge and the functional Schroedinger picture. We then consider the minimal Coulomb gauge and the Gribov problem of the gauge theory. The gauge fixing of the Coulomb gauge is done by using the Faddeev-Popov method, which enables the resolution of the Gauss law - the constraint on physical states. In the third chapter, we variationally solve the stationary Yang-Mills Schroedinger equation in Coulomb gauge for the vacuum state. Therefor we use a vacuum wave functional, which is strongly peaked at the Gribov horizon. The vacuum energy functional is calculated and minimized resulting in a set of coupled Schwinger-Dyson equations for the gluon energy, the ghost and Coulomb form factors and the curvature in gauge orbit space. Using the angular approximation these integral equations have been solved analytically in both the infrared and the ultraviolet regime. The asymptotic analytic solutions in the infrared and ultraviolet regime are reasonably well reproduced by the full numerical solutions of the coupled Schwinger-Dyson equations. In the fourth chapter, we investigate the dependence of the Yang-Mills wave functional in Coulomb gauge on the Faddeev-Popov determinant. (orig.)

Acid-producing capacity from sugars and sugar alcohols among Lactobacillus isolates collected in connection with radiation therapy.

Science.gov (United States)

Almståhl, Annica; Rudbäck, Helena; Basic, Amina; Carlén, Anette; Alstad, Torgny

2017-12-01

To investigate the acid-producing capacity from sugars and sugar alcohols of oral Lactobacillus collected in connection with radiation therapy (RT) to the head and neck region. Lactobacillus were collected from the tongue, buccal mucosa and supragingival plaque in 24 patients before, during, and after RT. The acid-producing capacity of Lactobacillus isolates (n=211) was analyzed using a colorimetric fermentation test in microtiter plates. Solutions containing 2% sugars (sucrose, glucose, fructose, lactose) or sugar-alcohols (sorbitol and xylitol) were used. After 24h of incubation, bacterial acid-producing capacity was determined as strong (pH6). Data regarding intake frequency of sugar-rich products and products with sugar-alcohols was collected. The highest acid-producing capacity using the sugars was seen for isolates collected during RT. Sorbitol was fermented to a higher extent during and post RT, especially among isolates from plaque. Lactobacillus fermenting xylitol showed the highest acid-producing capacity during RT (psugar-rich products or sugar-alcohol containing products and Lactobacillus acid-producing capacity, were found. The results suggest that Lactobacillus isolates, collected from the tongue, buccal mucosa and supragingival plaque, have a higher acid-producing capacity using sugars and sugar-alcohols during RT than one year post RT. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Effect of Sugar Price Policy on U.S. Imports of Processed Sugar-containing foods

OpenAIRE

Jabara, Cathy L.

1988-01-01

This paper examines the effects of sugar protection, as well as the effects of these other factors, on U.S. demand for imports of sugar-containing products. The paper also addresses two main issues: (1) whether substitution of alternative sweeteners has allowed U.S. food manufactures to reduce the competitive advantage provided to foreign manufactures by U.S. sugar policies, and (2) which countries -- developed or developing -- have been able to increase their exports of sugar-containing prod...

Isotope Fractionation of Water During Evaporation Without Condensation

International Nuclear Information System (INIS)

Cappa, Christopher D.; Drisdell, Walter S.; Smith, Jared D.; Saykally, Richard J.; Cohen, Ronald C.

2005-01-01

The microscopic events engendering liquid water evaporation have received much attention over the last century, but remain incompletely understood. We present measurements of isotope fractionation occurring during free molecular evaporation from liquid microjets and show that the isotope ratios of evaporating molecules exhibit dramatic differences from equilibrium vapor values, strong variations with the solution deuterium mole fraction, and a clear temperature dependence. These results indicate the existence of an energetic barrier to evaporation and that the evaporation coefficient of water is less than unity. These new insights into water evaporation promise to advance our understanding of the processes that control the formation and lifetime of clouds in the atmosphere.

A two-reagent neutralization scheme for controlling the migration of contaminants from a uranium mill tailing disposal pond

International Nuclear Information System (INIS)

Dodson, M.E.; Opitz, B.E.; Sherwood, D.R.

1985-01-01

Techniques for reducing contaminant migration from tailings liquor impoundments and evaporation ponds are being investigated by the Pacific Northwest Laboratory as part of the Nuclear Regulatory Commission's Uranium Research and Recovery Program. Building upon previous studies investigating single-reagent neutralization, laboratory experiments were conducted to evaluate the performance of a two-reagent neutralization scheme for the treatment of acidic uranium mill tailings liquors. Acidic tailings liquor, pH 3 neutralization to pH 4.0 followed by continued neutralization with lime to pH 7.3, resulted in the highest solution quality with respect to the Environmental Protection Agency's water quality guidelines. Furthermore, the two-reagent neutralization scheme is the most cost-effective treatment procedure tested to date

Sugar-free medicines are counterproductive.

Science.gov (United States)

Sundar, S

2012-09-01

Sugar in food and drinks is responsible for the poor dental health of many children and adults. On the other hand, there is no evidence that the small amount of sugar in medicines has been responsible for any dental problems. A recent British Heart Foundation survey found that nearly one in three UK children are eating sweets, chocolate and crisps three or more times a day. Hence it is futile administering sugar-free medicine to a child consuming lot of sweets. Moreover, sugar in medicines makes them palatable and bitter medicines inevitably affect compliance with the prescribed treatment. Poor compliance leads to inadequate treatment of illness and consequently increases the risk of complications from illness. Hence sugar-free medicines promoted as a public health policy could have actually caused more harm than any meaningful net benefit. There is an urgent need for a healthy debate and a fresh look at the policy of promoting sugar-free medicines.

Boilers, evaporators, and condensers

International Nuclear Information System (INIS)

Kakac, S.

1991-01-01

This book reports on the boilers, evaporators and condensers that are used in power plants including nuclear power plants. Topics included are forced convection for single-phase side heat exchangers, heat exchanger fouling, industrial heat exchanger design, fossil-fuel-fired boilers, once through boilers, thermodynamic designs of fossil fuel-first boilers, evaporators and condensers in refrigeration and air conditioning systems (with respect to reducing CFC's) and nuclear steam generators

Uranium mill tailings management practices in Saskatchewan, Canada

International Nuclear Information System (INIS)

Clifton, A.W.; Barsi, R.G.; Melis, L.A.

1984-01-01

Uranium was discovered in Saskatchewan in 1934. The first major mill began operating at Beaverlodge in 1953; two other mills began production in the same area in 1955 and 1957. Waste management measures were limited at the early mills. A new generation of mills was brought into production beginning in 1975 utilizing engineered waste management systems. The paper presents a brief description of the geography and physical environment of northern Saskatchewan, Canada; reviews milling operations and waste managements systems; describes the evolution of waste management systems; and, comments on environmental control measures regulating the industry

Respiration-Dependent Utilization of Sugars in Yeasts: a Determinant Role for Sugar Transporters

OpenAIRE

Goffrini, Paola; Ferrero, Iliana; Donnini, Claudia

2002-01-01

In many yeast species, including Kluyveromyces lactis, growth on certain sugars (such as galactose, raffinose, and maltose) occurs only under respiratory conditions. If respiration is blocked by inhibitors, mutation, or anaerobiosis, growth does not take place. This apparent dependence on respiration for the utilization of certain sugars has often been suspected to be associated with the mechanism of the sugar uptake step. We hypothesized that in many yeast species, the permease activities fo...

An evaporation driven pump for microfluidics applications

NARCIS (Netherlands)

Nie, C.; Mandamparambil, R.; Frijns, A.J.H.; den Toonder, J.M.J.; Tadrist, L.; Graur, I.

2014-01-01

We present an evaporation driven micro-pump for micro fluidic applications on a foil. In such a device, the evaporation rate is controlled by the geometry of the channel outlet and its temperature. The evaporation is also influenced by environmental parameters such as air humidity and temperature.

Synthesis and characterization of thermally evaporated Cu2SnSe3 ternary semiconductor

Science.gov (United States)

Hamdani, K.; Chaouche, M.; Benabdeslem, M.; Bechiri, L.; Benslim, N.; Amara, A.; Portier, X.; Bououdina, M.; Otmani, A.; Marie, P.

2014-11-01

Copper Tin Selenide (CuSnSe) powder was mechanically alloyed by high energy planetary ball milling, starting from elemental powders. Synthesis time and velocity have been optimized to produce Cu2SnSe3 materials. Thin films were prepared by thermal evaporation on Corning glass substrate at Ts = 300 °C. The structural, compositional, morphological and optical properties of the synthesized semiconductor have been analyzed by X-ray diffraction (XRD), energy dispersive X-ray analysis (EDAX), scanning electron microscopy (SEM) and transmission electron microscopy. The analyzed powder exhibited a cubic crystal structure, with the presence of Cu2Se as a secondary phase. On the other hand, the deposited films showed a cubic Cu2SnSe3 ternary phase and extra peaks belonging to some binary compounds. Furthermore, optical measurements showed that the deposited layers have a relatively high absorption coefficient of 105 cm-1 and present a band gap of 0.94 eV.

Water droplet evaporation from sticky superhydrophobic surfaces

Science.gov (United States)

Lee, Moonchan; Kim, Wuseok; Lee, Sanghee; Baek, Seunghyeon; Yong, Kijung; Jeon, Sangmin

2017-07-01

The evaporation dynamics of water from sticky superhydrophobic surfaces was investigated using a quartz crystal microresonator and an optical microscope. Anodic aluminum oxide (AAO) layers with different pore sizes were directly fabricated onto quartz crystal substrates and hydrophobized via chemical modification. The resulting AAO layers exhibited hydrophobic or superhydrophobic characteristics with strong adhesion to water due to the presence of sealed air pockets inside the nanopores. After placing a water droplet on the AAO membranes, variations in the resonance frequency and Q-factor were measured throughout the evaporation process, which were related to changes in mass and viscous damping, respectively. It was found that droplet evaporation from a sticky superhydrophobic surface followed a constant contact radius (CCR) mode in the early stage of evaporation and a combination of CCR and constant contact angle modes without a Cassie-Wenzel transition in the final stage. Furthermore, AAO membranes with larger pore sizes exhibited longer evaporation times, which were attributed to evaporative cooling at the droplet interface.

Wetting and evaporation of binary mixture drops.

Science.gov (United States)

Sefiane, Khellil; David, Samuel; Shanahan, Martin E R

2008-09-11

Experimental results on the wetting behavior of water, methanol, and binary mixture sessile drops on a smooth, polymer-coated substrate are reported. The wetting behavior of evaporating water/methanol drops was also studied in a water-saturated environment. Drop parameters (contact angle, shape, and volume) were monitored in time. The effects of the initial relative concentrations on subsequent evaporation and wetting dynamics were investigated. Physical mechanisms responsible for the various types of wetting behavior during different stages are proposed and discussed. Competition between evaporation and hydrodynamic flow are evoked. Using an environment saturated with water vapor allowed further exploration of the controlling mechanisms and underlying processes. Wetting stages attributed to differential evaporation of methanol were identified. Methanol, the more volatile component, evaporates predominantly in the initial stage. The data, however, suggest that a small proportion of methanol remained in the drop after the first stage of evaporation. This residual methanol within the drop seems to influence subsequent wetting behavior strongly.

Snap evaporation of droplets on smooth topographies.

Science.gov (United States)

Wells, Gary G; Ruiz-Gutiérrez, Élfego; Le Lirzin, Youen; Nourry, Anthony; Orme, Bethany V; Pradas, Marc; Ledesma-Aguilar, Rodrigo

2018-04-11

Droplet evaporation on solid surfaces is important in many applications including printing, micro-patterning and cooling. While seemingly simple, the configuration of evaporating droplets on solids is difficult to predict and control. This is because evaporation typically proceeds as a "stick-slip" sequence-a combination of pinning and de-pinning events dominated by static friction or "pinning", caused by microscopic surface roughness. Here we show how smooth, pinning-free, solid surfaces of non-planar topography promote a different process called snap evaporation. During snap evaporation a droplet follows a reproducible sequence of configurations, consisting of a quasi-static phase-change controlled by mass diffusion interrupted by out-of-equilibrium snaps. Snaps are triggered by bifurcations of the equilibrium droplet shape mediated by the underlying non-planar solid. Because the evolution of droplets during snap evaporation is controlled by a smooth topography, and not by surface roughness, our ideas can inspire programmable surfaces that manage liquids in heat- and mass-transfer applications.

Simultaneous spreading and evaporation: recent developments.

Science.gov (United States)

Semenov, Sergey; Trybala, Anna; Rubio, Ramon G; Kovalchuk, Nina; Starov, Victor; Velarde, Manuel G

2014-04-01

The recent progress in theoretical and experimental studies of simultaneous spreading and evaporation of liquid droplets on solid substrates is discussed for pure liquids including nanodroplets, nanosuspensions of inorganic particles (nanofluids) and surfactant solutions. Evaporation of both complete wetting and partial wetting liquids into a nonsaturated vapour atmosphere are considered. However, the main attention is paid to the case of partial wetting when the hysteresis of static contact angle takes place. In the case of complete wetting the spreading/evaporation process proceeds in two stages. A theory was suggested for this case and a good agreement with available experimental data was achieved. In the case of partial wetting the spreading/evaporation of a sessile droplet of pure liquid goes through four subsequent stages: (i) the initial stage, spreading, is relatively short (1-2 min) and therefore evaporation can be neglected during this stage; during the initial stage the contact angle reaches the value of advancing contact angle and the radius of the droplet base reaches its maximum value, (ii) the first stage of evaporation is characterised by the constant value of the radius of the droplet base; the value of the contact angle during the first stage decreases from static advancing to static receding contact angle; (iii) during the second stage of evaporation the contact angle remains constant and equal to its receding value, while the radius of the droplet base decreases; and (iv) at the third stage of evaporation both the contact angle and the radius of the droplet base decrease until the drop completely disappears. It has been shown theoretically and confirmed experimentally that during the first and second stages of evaporation the volume of droplet to power 2/3 decreases linearly with time. The universal dependence of the contact angle during the first stage and of the radius of the droplet base during the second stage on the reduced time has been

Sugar and Sugar Derivatives in Residues Produced from the UV Irradiation of Astrophysical Ice Analogs

Science.gov (United States)

Nuevo, M.; Sandford, S. A.; Cooper, G.

2016-01-01

A large variety and number of organic compounds of prebiotic interest are known to be present in carbonaceous chondrites. Among them, one sugar (dihydroxyacetone) as well as several sugar acids, sugar alcohols, and other sugar derivatives have been reported in the Murchison and Murray meteorites. Their presence, along with amino acids, amphiphiles, and nucleobases strongly suggests that molecules essential to life can form abiotically under astrophysical conditions. This hypothesis is supported by laboratory studies on the formation of complex organic molecules from the ultraviolet (UV) irradiation of simulated astrophysical ice mixtures consisting of H2O, CO, CO2, CH3OH, CH4, NH3, etc., at low temperature. In the past 15 years, these studies have shown that the organic residues recovered at room temperature contain amino acids, amphiphiles, nucleobases, as well as other complex organics. However, no systematic search for the presence of sugars and sugar derivatives in laboratory residues have been reported to date, despite the fact that those compounds are of primary prebiotic significance. Indeed, only small (up to 3 carbon atoms) sugar derivatives including glycerol and glyceric acid have been detected in residues so far.

Blue-shift in photoluminescence of ion-milled HgCdTe films and relaxation of defects induced by the milling

International Nuclear Information System (INIS)

Pociask, M.; Izhnin, I.I.; Mynbaev, K.D.; Izhnin, A.I.; Dvoretsky, S.A.; Mikhailov, N.N.; Sidorov, Yu.G.; Varavin, V.S.

2010-01-01

Simultaneous measurements of electrical conductivity, the Hall coefficient, and photoluminescence (PL) spectra of ion-milled Hg 1 - x Cd x Te films (x ∼ 0.30 and 0.38) were performed during post-milling ageing of the films at 293 K. In the course of the PL study, a 'relaxation' of the blue-shift of the PL band of ion-milled Hg 0.70 Cd 0.30 Te was observed. The relaxation was caused by the decrease of the electron concentration due to gradual disintegration of defects induced by the milling. It is shown that while ion milling substantially changes the electrical properties of Hg 1 - x Cd x Te, its PL spectrum in the long-term is affected insignificantly.

KSC ADVANCED GROUND BASED FIELD MILL V1

Data.gov (United States)

National Aeronautics and Space Administration — The Advanced Ground Based Field Mill (AGBFM) network consists of 34 (31 operational) field mills located at Kennedy Space Center (KSC), Florida. The field mills...

Theory of evapotranspiration. 2. Soil and intercepted water evaporation

OpenAIRE

Budagovskyi, Anatolij Ivanovič; Novák, Viliam

2011-01-01

Evaporation of water from the soil is described and quantified. Formation of the soil dry surface layer is quantitatively described, as a process resulting from the difference between the evaporation and upward soil water flux to the soil evaporating level. The results of evaporation analysis are generalized even for the case of water evaporation from the soil under canopy and interaction between evaporation rate and canopy transpiration is accounted for. Relationships describing evapotranspi...

Loop quantum corrected Einstein Yang-Mills black holes

Science.gov (United States)

Protter, Mason; DeBenedictis, Andrew

2018-05-01

In this paper, we study the homogeneous interiors of black holes possessing SU(2) Yang-Mills fields subject to corrections inspired by loop quantum gravity. The systems studied possess both magnetic and induced electric Yang-Mills fields. We consider the system of equations both with and without Wilson loop corrections to the Yang-Mills potential. The structure of the Yang-Mills Hamiltonian, along with the restriction to homogeneity, allows for an anomaly-free effective quantization. In particular, we study the bounce which replaces the classical singularity and the behavior of the Yang-Mills fields in the quantum corrected interior, which possesses topology R ×S2 . Beyond the bounce, the magnitude of the Yang-Mills electric field asymptotically grows monotonically. This results in an ever-expanding R sector even though the two-sphere volume is asymptotically constant. The results are similar with and without Wilson loop corrections on the Yang-Mills potential.

Sessile Drop Evaporation and Leidenfrost Phenomenon

OpenAIRE

A. K. Mozumder; M. R. Ullah; A. Hossain; M. A. Islam

2010-01-01

Problem statement: Quenching and cooling are important process in manufacturing industry for controlling the mechanical properties of materials, where evaporation is a vital mode of heat transfer. Approach: This study experimentally investigated the evaporation of sessile drop for four different heated surfaces of Aluminum, Brass, Copper and Mild steel with a combination of four different liquids as Methanol, Ethanol, Water and NaCl solution. The time of evaporation for the droplet on the hot...

A free sugars daily value (DV) identifies more "less healthy" prepackaged foods and beverages than a total sugars DV.

Science.gov (United States)

Bernstein, Jodi T; Labonté, Marie-Ève; Franco-Arellano, Beatriz; Schermel, Alyssa; L'Abbé, Mary R

2018-04-01

Regulatory changes in Canada will require food labels to have a benchmark [% Daily Value, %DV] for total sugars, based on 100 g/day, while US labels will require a %DV for added sugars, based on 50 g/day. The objective of this study was to compare two labelling policies, a total sugars DV (100 g/day) and a free sugars DV (50 g/day) on food labels. This cross-sectional analysis of the Food Label Information Program database focussed on top sources of total sugars intake in Canada (n = 6924 foods). Products were categorized as "less healthy" using two sets of criteria: a) free sugars levels exceeding the WHO guidelines (≥10% energy from free sugars); and b) exceeding healthfulness cut-offs of the Food Standards Australia New Zealand Nutrient Profiling Scoring Criterion (FSANZ-NPSC). The proportion of "less healthy" products with ≥15%DV (defined as "a lot" of sugars i.e. high in sugars, based on Health Canada's %DV labelling footnote and educational message for dietary guidance) were compared for each sugar labelling scenario. The free sugars DV showed better alignment with both methods for assessing "healthfulness" than the total sugars DV. The free sugars DV identified a greater proportion of "less healthy" foods with ≥15%DV, based on both the FSANZ-NPSC (70% vs. 45%, p chocolate bars, confectionery, and frozen desserts categories. Compared to total sugars DV labelling, using a free sugars DV identified more "less healthy" foods. Findings support the adoption of free sugars labelling. Copyright © 2018 Elsevier Inc. All rights reserved.

Aromatics extraction from pyrolytic sugars using ionic liquid to enhance sugar fermentability

NARCIS (Netherlands)

Li, X.; Luque-Moreno, L.C.; Oudenhoven, Stijn; Rehmann, L.; Kersten, Sascha R.A.; Schuur, Boelo

2016-01-01

Fermentative bioethanol production from pyrolytic sugars was improved via aromatics removal by liquid–liquid extraction. As solvents, the ionic liquid (IL) trihexyltetradecylphosphonium dicyanamide (P666,14[N(CN)2]) and ethyl acetate (EA) were compared. Two pyrolytic sugar solutions were created

How internal drainage affects evaporation dynamics from soil surfaces ?

Science.gov (United States)

Or, D.; Lehmann, P.; Sommer, M.

2017-12-01

Following rainfall, infiltrated water may be redistributed internally to larger depths or lost to the atmosphere by evaporation (and by plant uptake from depths at longer time scales). A large fraction of evaporative losses from terrestrial surfaces occurs during stage1 evaporation during which phase change occurs at the wet surface supplied by capillary flow from the soil. Recent studies have shown existence of a soil-dependent characteristic length below which capillary continuity is disrupted and a drastic shift to slower stage 2 evaporation ensues. Internal drainage hastens this transition and affect evaporative losses. To predict the transition to stage 2 and associated evaporative losses, we developed an analytical solution for evaporation dynamics with concurrent internal drainage. Expectedly, evaporative losses are suppressed when drainage is considered to different degrees depending on soil type and wetness. We observe that high initial water content supports rapid drainage and thus promotes the sheltering of soil water below the evaporation depth. The solution and laboratory experiments confirm nonlinear relationship between initial water content and total evaporative losses. The concept contributes to establishing bounds on regional surface evaporation considering rainfall characteristics and soil types.

Portable brine evaporator unit, process, and system

Science.gov (United States)

Hart, Paul John; Miller, Bruce G.; Wincek, Ronald T.; Decker, Glenn E.; Johnson, David K.

2009-04-07

The present invention discloses a comprehensive, efficient, and cost effective portable evaporator unit, method, and system for the treatment of brine. The evaporator unit, method, and system require a pretreatment process that removes heavy metals, crude oil, and other contaminates in preparation for the evaporator unit. The pretreatment and the evaporator unit, method, and system process metals and brine at the site where they are generated (the well site). Thus, saving significant money to producers who can avoid present and future increases in transportation costs.

Microbiological Spoilage of High-Sugar Products

Science.gov (United States)

Thompson, Sterling

The high-sugar products discussed in this chapter are referred to as chocolate, sugar confectionery (non-chocolate), liquid sugars, sugar syrups, and honey. Products grouped in the sugar confectionery category include hard candy, soft/gummy candy, caramel, toffee, licorice, marzipan, creams, jellies, and nougats. A common intrinsic parameter associated with high-sugar products is their low water activity (a w), which is known to inhibit the growth of most spoilage and pathogenic bacteria. However, spoilage can occur as a result of the growth of osmophilic yeasts and xerophilic molds (Von Richter, 1912; Anand & Brown, 1968; Brown, 1976). The a w range for high-sugar products is between 0.20 and 0.80 (Banwart, 1979; Richardson, 1987; Lenovich & Konkel, 1992; ICMSF, 1998; Jay, Loessner, & Golden, 2005). Spoilage of products, such as chocolate-covered cherries, results from the presence of yeasts in the liquid sugar brine or the cherry. Generally, the spoiled product will develop leakers. The chocolate covering the cherry would not likely be a source of yeast contamination.

I Mend It With Sugar

OpenAIRE

Lindvall, Charlotta

2015-01-01

I mend it with sugar         Abstract   "Gluttony" and "sloth" is the sugar addictions best friend, or could it be that the addiction comes out of a disturbed hormone production caused by the environment that surrounds us? Trying to understand my own sugar addiction I weave in my personal story into my artistic research around this subject. The sugar might be the cause of the pandemic obesity and that's why it has to bee brought up into the light from its darkness down the basement of the fo...

Spacesuit Water Membrane Evaporator; An Enhanced Evaporative Cooling Systems for the Advanced Extravehicular Mobility Unit Portable Life Support System

Science.gov (United States)

Bue, Grant C.; Makinen, Janice V.; Miller, Sean.; Campbell, Colin; Lynch, Bill; Vogel, Matt; Craft, Jesse; Petty, Brian

2014-01-01

Spacesuit Water Membrane Evaporator - Baseline heat rejection technology for the Portable Life Support System of the Advanced EMU center dot Replaces sublimator in the current EMU center dot Contamination insensitive center dot Can work with Lithium Chloride Absorber Radiator in Spacesuit Evaporator Absorber Radiator (SEAR) to reject heat and reuse evaporated water The Spacesuit Water Membrane Evaporator (SWME) is being developed to replace the sublimator for future generation spacesuits. Water in LCVG absorbs body heat while circulating center dot Warm water pumped through SWME center dot SWME evaporates water vapor, while maintaining liquid water - Cools water center dot Cooled water is then recirculated through LCVG. center dot LCVG water lost due to evaporation (cooling) is replaced from feedwater The Independent TCV Manifold reduces design complexity and manufacturing difficulty of the SWME End Cap. center dot The offset motor for the new BPV reduces the volume profile of the SWME by laying the motor flat on the End Cap alongside the TCV.

Influence of fine grinding on the hydrolysis of cellulosic materials - acid vs enzymic

Energy Technology Data Exchange (ETDEWEB)

Millet, M A; Effland, M J; Caulfield, D F

1979-01-01

The effect of vibratory milling on the enzymic and dilute H/sub 2/SO/sub 4/ hydrolysis of cotton linters, newsprint, Douglas fir, and red oak was investigated by determining the rate and degree of hydrolysis, maximum yield of reducing sugars, and cellulose crystallinity index. Linters were totally hydrolyzed in 10 days after 60 min milling; oak carbohydrates were 93% convertible to sugar in the same period after 240 min milling. Vibratory milling substantially increased the rates of acid hydrolysis of all 4 substrates, nearly 9- and 5-fold for linters and other lignocellulosic materials, respectively. Increases in maximum sugar yields under batch conditions were 60 to 140% higher than those for unmilled materials.

75 FR 23631 - Sugar Re-Export Program, the Sugar-Containing Products Re-Export Program, and the Polyhydric...

Science.gov (United States)

2010-05-04

... Part 1530 Sugar Re-Export Program, the Sugar-Containing Products Re-Export Program, and the Polyhydric...), Additional U.S. Note 6, which authorizes entry of raw cane sugar under subheading 1701.11.20 of the HTS for the production of polyhydric alcohols, except polyhydric alcohols for use as a substitute for sugar in...

Control of black hole evaporation?

International Nuclear Information System (INIS)

Ahn, Doyeol

2007-01-01

Contradiction between Hawking's semi-classical arguments and the string theory on the evaporation of a black hole has been one of the most intriguing problems in fundamental physics. A final-state boundary condition inside the black hole was proposed by Horowitz and Maldacena to resolve this contradiction. We point out that the original Hawking effect can also be regarded as a separate boundary condition at the event horizon for this scenario. Here, we found that the change of the Hawking boundary condition may affect the information transfer from the initial collapsing matter to the outgoing Hawking radiation during the evaporation process and as a result the evaporation process itself, significantly

Interfacial Instabilities in Evaporating Drops

Science.gov (United States)

Moffat, Ross; Sefiane, Khellil; Matar, Omar

2007-11-01

We study the effect of substrate thermal properties on the evaporation of sessile drops of various liquids. An infra-red imaging technique was used to record the interfacial temperature. This technique illustrates the non-uniformity in interfacial temperature distribution that characterises the evaporation process. Our results also demonstrate that the evaporation of methanol droplets is accompanied by the formation of wave-trains in the interfacial temperature field; similar patterns, however, were not observed in the case of water droplets. More complex patterns are observed for FC-72 refrigerant drops. The effect of substrate thermal conductivity on the structure of the complex pattern formation is also elucidated.

Advanced evaporator technology progress report FY 1992

Energy Technology Data Exchange (ETDEWEB)

Chamberlain, D.; Hutter, J.C.; Leonard, R.A. [and others

1995-01-01

This report summarizes the work that was completed in FY 1992 on the program {open_quotes}Technology Development for Concentrating Process Streams.{close_quotes} The purpose of this program is to evaluate and develop evaporator technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process. Concentrating these streams and minimizing the volume of waste generated can significantly reduce disposal costs; however, equipment to concentrate the streams and recycle the decontaminated condensates must be installed. LICON, Inc., is developing an evaporator that shows a great deal of potential for this application. In this report, concepts that need to be incorporated into the design of an evaporator operated in a radioactive environment are discussed. These concepts include criticality safety, remote operation and maintenance, and materials of construction. Both solubility and vapor-liquid equilibrium data are needed to design an effective process for concentrating process streams. Therefore, literature surveys were completed and are summarized in this report. A model that is being developed to predict vapor phase compositions is described. A laboratory-scale evaporator was purchased and installed to study the evaporation process and to collect additional data. This unit is described in detail. Two new LICON evaporators are being designed for installation at Argonne-East in FY 1993 to process low-level radioactive waste generated throughout the laboratory. They will also provide operating data from a full-sized evaporator processing radioactive solutions. Details on these evaporators are included in this report.

Advanced evaporator technology progress report FY 1992

International Nuclear Information System (INIS)

Chamberlain, D.; Hutter, J.C.; Leonard, R.A.

1995-01-01

This report summarizes the work that was completed in FY 1992 on the program open-quotes Technology Development for Concentrating Process Streams.close quotes The purpose of this program is to evaluate and develop evaporator technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process. Concentrating these streams and minimizing the volume of waste generated can significantly reduce disposal costs; however, equipment to concentrate the streams and recycle the decontaminated condensates must be installed. LICON, Inc., is developing an evaporator that shows a great deal of potential for this application. In this report, concepts that need to be incorporated into the design of an evaporator operated in a radioactive environment are discussed. These concepts include criticality safety, remote operation and maintenance, and materials of construction. Both solubility and vapor-liquid equilibrium data are needed to design an effective process for concentrating process streams. Therefore, literature surveys were completed and are summarized in this report. A model that is being developed to predict vapor phase compositions is described. A laboratory-scale evaporator was purchased and installed to study the evaporation process and to collect additional data. This unit is described in detail. Two new LICON evaporators are being designed for installation at Argonne-East in FY 1993 to process low-level radioactive waste generated throughout the laboratory. They will also provide operating data from a full-sized evaporator processing radioactive solutions. Details on these evaporators are included in this report

Low blood sugar - newborns

Science.gov (United States)

... this page: //medlineplus.gov/ency/article/007306.htm Low blood sugar - newborns To use the sharing features on this page, please enable JavaScript. A low blood sugar level in newborn babies is also ...

Sugar Price Supports and Taxation

Science.gov (United States)

Dilk, Abby; Savaiano, Dennis A.

2017-01-01

Domestic US sugar production has been protected by government policy for the past 82 years, resulting in elevated domestic prices and an estimated annual (2013) $1.4 billion dollar “tax” on consumers. These elevated prices and the simultaneous federal support for domestic corn production have ensured a strong market for high-fructose corn syrup. Americans have dramatically increased their consumption of caloric sweeteners during the same period. Consumption of “empty” calories (ie, foods with low-nutrient/high-caloric density)—sugar and high-fructose corn syrup being the primary sources—is considered by most public health experts to be a key contributing factor to the rise in obesity. There have been substantial efforts to tax sugar-sweetened beverages (SSBs) to both reduce consumption and provide a source of funds for nutrition education, thereby emulating the tobacco tax model. Volume-based SSB taxes levy the tax rate per ounce of liquid, where some are only imposed on beverages with added sugar content exceeding a set threshold. Nonetheless, volume-based taxes have significant limitations in encouraging consumers to reduce their caloric intake due to a lack of transparency at the point of purchase. Thus, it is hypothesized that point-of-purchase, nutrient-specific excise taxes on SSBs would be more effective at reducing sugar consumption. However, all SSB taxes are limited by the possibility that consumers may compensate their decreased intake from SSBs with other high-calorie junk foods. Furthermore, there are no existing studies to provide evidence on how SSB taxes will impact obesity rates in the long term. The paradox of sugar prices is that Americans have paid higher prices for sugar to protect domestic production for more than 80 years, and now, Americans are being asked to pay even more to promote public health. The effective use of sugar taxes should be considered based on their merits in reducing sugar consumption and making available a new

Decolorization of turbid sugar juice from sugar factory using waste powdered carbon

Science.gov (United States)

Aljohani, Hind; Ahmed, Youssef; El-Shafey, Ola; El-Shafey, Shaymaa; Fouad, Rasha; Shoueir, Kamel

2018-03-01

Waste management of powdered activated carbon from cyclone of some sugar factories was used for decolorization of sugar mud juice (SMJ) in this study. The presence of powdered activated carbon waste (PACW) was admitted again for their use in SMJ decolorization. The determined specific surface area are typically S BET = 613.887 m2/g and the pore distribution lies in mesoporous domain. Color removal (CR%) and decolorization capacity (DC) of the characterized PACW are similar to those of decolorants used at this time for sugar refining. The CR% with PACW reached 81.03% at pH7.0 and dosed in the amount 0.5 g/50 ml of SMJ. There are two acceptable mechanisms illustrates the attachments between phenols and carboxylate ions. In this paper, we put a simple and rapid dark liquid decolorization by controlling rejected carbon waste, which will be useful for treatment of dark liquid sugar.

Steady Method for the Analysis of Evaporation Dynamics.

Science.gov (United States)

Günay, A Alperen; Sett, Soumyadip; Oh, Junho; Miljkovic, Nenad

2017-10-31

Droplet evaporation is an important phenomenon governing many man-made and natural processes. Characterizing the rate of evaporation with high accuracy has attracted the attention of numerous scientists over the past century. Traditionally, researchers have studied evaporation by observing the change in the droplet size in a given time interval. However, the transient nature coupled with the significant mass-transfer-governed gas dynamics occurring at the droplet three-phase contact line makes the classical method crude. Furthermore, the intricate balance played by the internal and external flows, evaporation kinetics, thermocapillarity, binary-mixture dynamics, curvature, and moving contact lines makes the decoupling of these processes impossible with classical transient methods. Here, we present a method to measure the rate of evaporation of spatially and temporally steady droplets. By utilizing a piezoelectric dispenser to feed microscale droplets (R ≈ 9 μm) to a larger evaporating droplet at a prescribed frequency, we can both create variable-sized droplets on any surface and study their evaporation rate by modulating the piezoelectric droplet addition frequency. Using our steady technique, we studied water evaporation of droplets having base radii ranging from 20 to 250 μm on surfaces of different functionalities (45° ≤ θ a,app ≤ 162°, where θ a,app is the apparent advancing contact angle). We benchmarked our technique with the classical unsteady method, showing an improvement of 140% in evaporation rate measurement accuracy. Our work not only characterizes the evaporation dynamics on functional surfaces but also provides an experimental platform to finally enable the decoupling of the complex physics governing the ubiquitous droplet evaporation process.

Sugar, acid and furfural quantification in a sulphite pulp mill: Feedstock, product and hydrolysate analysis by HPLC/RID

Directory of Open Access Journals (Sweden)

Tamara Llano

2017-09-01

The analysis of major and minor monosaccharides, aliphatic carboxylic acids and furfurals has been optimised. An important drawback of the spent liquors generated after sulphite pulping is their acidic nature, high viscosity and adhesive properties that interfere in the column lifetime. This work recommends both a CHO-782Pb column for the sugar analysis and an SH-1011 resin-based cross-linked gel column to separate low-molecular-weight chain acids, alcohols and furfurals. Such columns resulted in a good separation with long lifetime, wide pH operating range and low fouling issues.

Design and operation of evaporators for radioactive wastes

Energy Technology Data Exchange (ETDEWEB)

Yamomoto, Y [comp.; Tokyo Univ. (Japan)

1968-05-01

A manual dealing with the application of evaporators to the treatment of liquid radioactive wastes. This book is the second of three commissioned by the IAEA on the three on the three principal techniques for concentrating radioactive wastes, namely chemical precipitation, evaporation and ion-exchange. Informations on different types of evaporators and related equipment and their operational procedures are given in this document. It also gives different means of disposal of evaporator condensates and concentrates and a rough estimate of costs of radioactive waste evaporator plant and its operation. 58 refs, 43 figs, 5 tabs.

Design and operation of evaporators for radioactive wastes

International Nuclear Information System (INIS)

Yamomoto, Y.

1968-01-01

A manual dealing with the application of evaporators to the treatment of liquid radioactive wastes. This book is the second of three commissioned by the IAEA on the three on the three principal techniques for concentrating radioactive wastes, namely chemical precipitation, evaporation and ion-exchange. Informations on different types of evaporators and related equipment and their operational procedures are given in this document. It also gives different means of disposal of evaporator condensates and concentrates and a rough estimate of costs of radioactive waste evaporator plant and its operation. 58 refs, 43 figs, 5 tabs

Low-temperature field evaporation of Nb3Sn compound

International Nuclear Information System (INIS)

Ksenofontov, V.A.; Kul'ko, V.B.; Kutsenko, P.A.

1986-01-01

Investigation results on field evaporation of superconducting Nb 3 Sn compound wth A15 lattice are presented. Compound evaporation is shown to proceed in two stages. Evaporation field and ionic composition of evaporating material are determined. It is found out that in strong electric fields compound surface represents niobium skeleton, wich does not form regular image. Comparison of ion-microscopic and calculated images formed by low-temperature field evaporation indicates to possibility of sample surface reconstruction after preferable tin evaporation

Factors associated with the acceptance of sugar and sugar substitutes by the public.

Science.gov (United States)

Mackay, D A

1985-09-01

Acceptance is described in both market and sensory research terminology and recent developments in the fields of applied psychology and physiology are examined for their pertinence to public acceptance of sucrose and its substitutes. Information on the function of sucrose in foods other than beverages is presented with emphasis on salivation as an acceptance factor and attention is drawn to its possible dental significance. Distinctions are made between the sweetening and bulking properties of sucrose and sugar substitutes. Factors having a bearing on the acceptance of sweet foods and the determination of their optimal sugar content are described in detail. While major decreases in sucrose intake in the US resulted from high-fructose corn-sweetener usage in soft drinks, no evidence is yet available to suggest that the use of sugar substitutes of the intense artificial sweetener type has caused any decrease in ordinary sugar consumption. Neither is the consumption of polyols (sorbitol, mannitol, xylitol) high enough in confectionery categories to cause any discernible decrease in sugar usage. The evidence suggests not so much that sugar substitutes may have stopped the growth in sucrose usage, but that new product categories such as diet foods and "sugarless' confections may have been created. These categories were never available to fermentable carbohydrate sweeteners and equivalence in acceptance to sucrose-sweetened products was not an important factor in their growth.(ABSTRACT TRUNCATED AT 250 WORDS)

PROCESS OF OBTAINING OF SUGAR FROM SUGAR BEET AND INFLUENCE ON ITS QUALITY

Directory of Open Access Journals (Sweden)

Marián Tokár

2011-02-01

Full Text Available Cooking of massecuites has been study in the connection with different particle size distribution of white sugar. During the crystallization is possible to operate with parameters which have influence on particle size of white sugar. Dry matter of juice in crystallizer, volume of the standard syrup in crystallizer and heating curve of crystallization process are constant parameters in this process. Quantity of slurry (seed magma crystallizate and volume of slurry massecuite are parameters which can be changed for control the particle size distribution of white sugar. Five variants of viable parameters have been trying for obtain ideal particle size distribution of white sugar. As a best has been evaluated variant with 1100 cm3 of slurry and 20 % of volume of slurry massecuite in crystallizer. This variant has had the crystals proportions captured by the sieves between 1.00 and 0.40 mm with minimal differences in weight. More results have been related to reduction of losses of sugar in molasses with the right setting for the line of cooling crystallization process. The looses of sugar can be reduced by adding two coolers in the end of cooling crystalization process what will decrease a temperature to 40 ° C. This temperature will lead to more efficient crystallization in the cooling crystallization process.doi:10.5219/122

ROMI 4.0: Updated Rough Mill Simulator

Science.gov (United States)

Timo Grueneberg; R. Edward Thomas; Urs Buehlmann

2012-01-01

In the secondary hardwood industry, rough mills convert hardwood lumber into dimension parts for furniture, cabinets, and other wood products. ROMI 4.0, the US Department of Agriculture Forest Service's ROugh-MIll simulator, is a software package designed to simulate the cut-up of hardwood lumber in rough mills in such a way that a maximum possible component yield...

Optimisation of milling parameters using neural network

Directory of Open Access Journals (Sweden)

Lipski Jerzy

2017-01-01

Full Text Available The purpose of this study was to design and test an intelligent computer software developed with the purpose of increasing average productivity of milling not compromising the design features of the final product. The developed system generates optimal milling parameters based on the extent of tool wear. The introduced optimisation algorithm employs a multilayer model of a milling process developed in the artificial neural network. The input parameters for model training are the following: cutting speed vc, feed per tooth fz and the degree of tool wear measured by means of localised flank wear (VB3. The output parameter is the surface roughness of a machined surface Ra. Since the model in the neural network exhibits good approximation of functional relationships, it was applied to determine optimal milling parameters in changeable tool wear conditions (VB3 and stabilisation of surface roughness parameter Ra. Our solution enables constant control over surface roughness parameters and productivity of milling process after each assessment of tool condition. The recommended parameters, i.e. those which applied in milling ensure desired surface roughness and maximal productivity, are selected from all the parameters generated by the model. The developed software may constitute an expert system supporting a milling machine operator. In addition, the application may be installed on a mobile device (smartphone, connected to a tool wear diagnostics instrument and the machine tool controller in order to supply updated optimal parameters of milling. The presented solution facilitates tool life optimisation and decreasing tool change costs, particularly during prolonged operation.

Two-reagent neutralization scheme for controlling the migration of contaminants from a uranium mill tailings disposal pond

International Nuclear Information System (INIS)

Dodson, M.E.; Opitz, B.E.; Sherwood, D.R.

1984-11-01

Techniques for reducing contaminant migration from tailings liquor impoundments and evaporation ponds are being investigated by the Pacific Northwest Laboratory as part of the Nuclear Regulatory Commission's Uranium Research and Recovery Program. Building upon previous studies investigating single-reagent neutralization, laboratory experiments were conducted to evaluate the performance of a two-reagent neutralization scheme for the treatment of acidic uranium mill tailings liquors. Acidic tailings liquor, pH 3 neutralization to pH 4.0 followed by continued neutralization with lime to pH 7.3, resulted in the highest solution quality with respect to the Environmental Protection Agency's water quality guidelines. Furthermore, the two-reagent neutralization scheme is the most cost-effective treatment procedure tested to date. 13 references, 1 table

Evaporation of nanofluid droplet on heated surface

Directory of Open Access Journals (Sweden)

Yeung Chan Kim

2015-04-01

Full Text Available In this study, an experiment on the evaporation of nanofluid sessile droplet on a heated surface was conducted. A nanofluid of 0.5% volumetric concentration mixed with 80-nm-sized CuO powder and pure water were used for experiment. Droplet was applied to the heated surface, and images of the evaporation process were obtained. The recorded images were analyzed to find the volume, diameter, and contact angle of the droplet. In addition, the evaporative heat transfer coefficient was calculated from experimental result. The results of this study are summarized as follows: the base diameter of the droplet was maintained stably during the evaporation. The measured temperature of the droplet was increased rapidly for a very short time, then maintained constantly. The nanofluid droplet was evaporated faster than the pure water droplet under the experimental conditions of the same initial volume and temperature, and the average evaporative heat transfer coefficient of the nanofluid droplet was higher than that of pure water. We can consider the effects of the initial contact angle and thermal conductivity of nanofluid as the reason for this experimental result. However, the effect of surface roughness on the evaporative heat transfer of nanofluid droplet appeared unclear.

Evaporation rate-based selection of supramolecular chirality.

Science.gov (United States)

Hattori, Shingo; Vandendriessche, Stefaan; Koeckelberghs, Guy; Verbiest, Thierry; Ishii, Kazuyuki

2017-03-09

We demonstrate the evaporation rate-based selection of supramolecular chirality for the first time. P-type aggregates prepared by fast evaporation, and M-type aggregates prepared by slow evaporation are kinetic and thermodynamic products under dynamic reaction conditions, respectively. These findings provide a novel solution reaction chemistry under the dynamic reaction conditions.

Added sugars in kids' meals from chain restaurants.

Science.gov (United States)

Scourboutakos, Mary J; Semnani-Azad, Zhila; L'Abbé, Mary R

2016-06-01

To analyze the added sugars in kids' meals from Canadian chain restaurants in relation to the World Health Organization's proposed sugar recommendation (less than 5% of total daily calories should come from added sugars) and current recommendation (less than 10% of total daily calories should come from added sugars). Total sugar levels were retrieved from the websites of 10 fast-food and 7 sit-down restaurants in 2010. The added sugar levels in 3178 kids' meals from Canadian chain restaurants were calculated in 2014 (in Toronto, Canada) by subtracting all naturally occurring sugars from the total sugar level. The average amount of added sugars in restaurant kids' meals (25 ± 0.36 g) exceeded the WHO's proposed daily recommendation for sugar intake. There was a wide range of added sugar levels in kids' meals ranging from 0 g to 114 g. 50% of meals exceeded the WHO's proposed daily sugar recommendation, and 19% exceeded the WHO's current daily sugar recommendation. There is a wide range of sugar levels in kids' meals from restaurants, and many contain more than a day's worth of sugar.

Properties and sinterability of wet and dry attrition-milled OREOXed powder

International Nuclear Information System (INIS)

Lee, J. W.; Kim, J. H.; Kim, W. K.; Park, K. I.; Lee, J. W.

2001-01-01

The powder properties and sinterability were investigated with the powder prepared by wet and dry attrition milling of OREOX-treated powder. The OREOX-treated powder was prepared from the simulated spent fuel. Powder having less than 1 μm of average particle size could be obtained by dry milling, but not be obtained by wet milling. Thus, specific surface area of dry milled powder was higher than that of wet milled powder. With increasing of milling time, dry milled powder formed dense agglomerate while wet milled powder showed loose agglomerate. The pellets with higher than 95% T.D. of sintered density and larger than 7 μm of grain size were made with the milled powder regardless of milling method. The milling time in wet milling has greatly improved the sinterability. The pellets produced with dry milled powder have higher sintered density and larger grain size

Sugar addiction: the state of the science.

Science.gov (United States)

Westwater, Margaret L; Fletcher, Paul C; Ziauddeen, Hisham

2016-11-01

As obesity rates continue to climb, the notion that overconsumption reflects an underlying 'food addiction' (FA) has become increasingly influential. An increasingly popular theory is that sugar acts as an addictive agent, eliciting neurobiological changes similar to those seen in drug addiction. In this paper, we review the evidence in support of sugar addiction. We reviewed the literature on food and sugar addiction and considered the evidence suggesting the addictiveness of highly processed foods, particularly those with high sugar content. We then examined the addictive potential of sugar by contrasting evidence from the animal and human neuroscience literature on drug and sugar addiction. We find little evidence to support sugar addiction in humans, and findings from the animal literature suggest that addiction-like behaviours, such as bingeing, occur only in the context of intermittent access to sugar. These behaviours likely arise from intermittent access to sweet tasting or highly palatable foods, not the neurochemical effects of sugar. Given the lack of evidence supporting it, we argue against a premature incorporation of sugar addiction into the scientific literature and public policy recommendations.

A Loose Relationship: Incomplete H+/Sugar Coupling in the MFS Sugar Transporter GlcP.

Science.gov (United States)

Bazzone, Andre; Zabadne, Annas J; Salisowski, Anastasia; Madej, M Gregor; Fendler, Klaus

2017-12-19

The glucose transporter from Staphylococcus epidermidis, GlcP Se , is a homolog of the human GLUT sugar transporters of the major facilitator superfamily. Together with the xylose transporter from Escherichia coli, XylE Ec , the other prominent prokaryotic GLUT homolog, GlcP Se , is equipped with a conserved proton-binding site arguing for an electrogenic transport mode. However, the electrophysiological analysis of GlcP Se presented here reveals important differences between the two GLUT homologs. GlcP Se , unlike XylE Ec , does not perform steady-state electrogenic transport at symmetrical pH conditions. Furthermore, when a pH gradient is applied, partially uncoupled transport modes can be generated. In contrast to other bacterial sugar transporters analyzed so far, in GlcP Se sugar binding, translocation and release are also accomplished by the deprotonated transporter. Based on these experimental results, we conclude that coupling of sugar and H + transport is incomplete in GlcP Se . To verify the viability of the observed partially coupled GlcP Se transport modes, we propose a universal eight-state kinetic model in which any degree of coupling is realized and H + /sugar symport represents only a specific instance. Furthermore, using sequence comparison with strictly coupled XylE Ec and similar sugar transporters, we identify an additional charged residue that may be essential for effective H + /sugar symport. Copyright © 2017 Biophysical Society. Published by Elsevier Inc. All rights reserved.

Water Evaporation from Acoustically Levitated Aqueous Solution Droplets.

Science.gov (United States)

Combe, Nicole A; Donaldson, D James

2017-09-28

We present a systematic study of the effect of solutes on the evaporation rate of acoustically levitated aqueous solution droplets by suspending individual droplets in a zero-relative humidity environment and measuring their size as a function of time. The ratios of the early time evaporation rates of six simple salts (NaCl, NaBr, NaNO 3 , KCl, MgCl 2 , CaCl 2 ) and malonic acid to that of water are in excellent agreement with predictions made by modifying the Maxwell equation to include the time-dependent water activity of the evaporating aqueous salt solution droplets. However, the early time evaporation rates of three ammonium salt solutions (NH 4 Cl, NH 4 NO 3 , (NH 4 ) 2 SO 4 ) are not significantly different from the evaporation rate of pure water. This finding is in accord with a previous report that ammonium sulfate does not depress the evaporation rate of its solutions, despite reducing its water vapor pressure, perhaps due to specific surface effects. At longer evaporation times, as the droplets approach crystallization, all but one (MgCl 2 ) of the solution evaporation rates are well described by the modified Maxwell equation.

Pavement maintenance procedures with and without milling materials

Directory of Open Access Journals (Sweden)

Rafiqul A. Tarefder

2016-01-01

Full Text Available This study evaluates maintenance treatment followed by different Districts of New Mexico Department of Transportation (NMDOT. In addition, two case studies on the use of old pavement materials, called the “millings”, in maintenance projects are reported. Based on this study, it is observed that none of the Districts have a written procedure for maintenance work. Rather Districts rely on the experience of the maintenance crew for conducting maintenance projects. All Districts prefer to use chip seal for maintenance irrespective of distress conditions of the pavements. Patching and crack sealing are usually done before chip sealing to extend the life of the chip seals. Sand seal, scrub seal, and slurry seal projects are not done by District maintenance crews but by outside contractors. It is also observed that all Districts are interested in using millings in maintenance projects and most have already used millings in at least one maintenance project with some success and failure. Most of the Districts have used coarse fraction of millings in chip seal projects successfully. However, they failed to find a proper way to process the fine fractions of millings. Case Study I shows that fine millings can be used to construct thin overlay when mixed with emulsion in pug mill or hot drums. Case Study II concludes that fine millings can be used as fine/sand seal successfully following the same procedure and using the same equipment as chip seal. Keywords: Millings, Maintenance, Emulsion, Rutting, Pug-mill

Urban evaporation rates for water-permeable pavements.

Science.gov (United States)

Starke, P; Göbel, P; Coldewey, W G

2010-01-01

In urban areas the natural water balance is disturbed. Infiltration and evaporation are reduced, resulting in a high surface runoff and a typical city climate, which can lead to floods and damages. Water-permeable pavements have a high infiltration rate that reduces surface runoff by increasing the groundwater recharge. The high water retention capacity of the street body of up to 51 l/m(2) and its connection via pores to the surface lead to higher evaporation rates than impermeable surfaces. A comparison of these two kinds of pavements shows a 16% increase in evaporation levels of water-permeable pavements. Furthermore, the evaporation from impermeable pavements is linked directly to rain events due to fast-drying surfaces. Water-permeable pavements show a more evenly distributed evaporation after a rain event. Cooling effects by evaporative heat loss can improve the city climate even several days after rain events. On a large scale use, uncomfortable weather like sultriness or dry heat can be prevented and the urban water balance can be attenuated towards the natural.

Estimating soil water evaporation using radar measurements

Science.gov (United States)

Sadeghi, Ali M.; Scott, H. D.; Waite, W. P.; Asrar, G.

1988-01-01

Field studies were conducted to evaluate the application of radar reflectivity as compared with the shortwave reflectivity (albedo) used in the Idso-Jackson equation for the estimation of daily evaporation under overcast sky and subhumid climatic conditions. Soil water content, water potential, shortwave and radar reflectivity, and soil and air temperatures were monitored during three soil drying cycles. The data from each cycle were used to calculate daily evaporation from the Idso-Jackson equation and from two other standard methods, the modified Penman and plane of zero-flux. All three methods resulted in similar estimates of evaporation under clear sky conditions; however, under overcast sky conditions, evaporation fluxes computed from the Idso-Jackson equation were consistently lower than the other two methods. The shortwave albedo values in the Idso-Jackson equation were then replaced with radar reflectivities and a new set of total daily evaporation fluxes were calculated. This resulted in a significant improvement in computed soil evaporation fluxes from the Idso-Jackson equation, and a better agreement between the three methods under overcast sky conditions.

Systematics of evaporation

International Nuclear Information System (INIS)

Klots, C.E.

1991-01-01

Beginning with rather basic principles, general relations are obtained for evaporative rate constants. These are established both as a function of energy and of temperature. In parallel with this, expressions are developed for the kinetic energy distribution of the separating species. Explicit evaluation of the rate constants in the case of 'chemical' evaporation from an entity containing n monomeric units yields as a typical result k(T)(s -1 )=3.10 13 n 2/3 exp[6/n 1/3 ]exp(-ΔE a (n)/k B T). Experimental evidence in support of this relation is cited. Applications to thermionic emission are also noted. (orig.)

Jaduguda uranium mill : rich experiences for future challenges

International Nuclear Information System (INIS)

Beri, K.K.

1991-01-01

India's only uranium milling plant at Jaduguda was commissioned in 1967-68 utilising low grade uranium ore. The flowsheet of the mill and controlling parameters were based on studies done on laboratory and pilot plant scale tests at the Bhabha Atomic Research Centre, Bombay. The mill has worked upto expectation except in few areas where modifications had to be done for smooth production. Apart from this improvements in operating practices have been done based on experience gained in operating the mill, incorporating the recent technological advances. In the recent past, the mill was expanded to increase the installed capacity by 40% and was commissioned in October 1987. The expanded mill has given the desired capacity and is working smoothly. The present paper deals with the experience gained in running the plant for the last 20 years and changes incorporated (author). 4 figs

Validation of a simple evaporation-transpiration scheme (SETS) to estimate evaporation using micro-lysimeter measurements

Science.gov (United States)

Ghazanfari, Sadegh; Pande, Saket; Savenije, Hubert

2014-05-01

Several methods exist to estimate E and T. The Penman-Montieth or Priestly-Taylor methods along with the Jarvis scheme for estimating vegetation resistance are commonly used to estimate these fluxes as a function of land cover, atmospheric forcing and soil moisture content. In this study, a simple evaporation transpiration method is developed based on MOSAIC Land Surface Model that explicitly accounts for soil moisture. Soil evaporation and transpiration estimated by SETS is validated on a single column of soil profile with measured evaporation data from three micro-lysimeters located at Ferdowsi University of Mashhad synoptic station, Iran, for the year 2005. SETS is run using both implicit and explicit computational schemes. Results show that the implicit scheme estimates the vapor flux close to that by the explicit scheme. The mean difference between the implicit and explicit scheme is -0.03 mm/day. The paired T-test of mean difference (p-Value = 0.042 and t-Value = 2.04) shows that there is no significant difference between the two methods. The sum of soil evaporation and transpiration from SETS is also compared with P-M equation and micro-lysimeters measurements. The SETS predicts the actual evaporation with a lower bias (= 1.24mm/day) than P-M (= 1.82 mm/day) and with R2 value of 0.82.

The continuous similarity model of bulk soil-water evaporation

Science.gov (United States)

Clapp, R. B.

1983-01-01

The continuous similarity model of evaporation is described. In it, evaporation is conceptualized as a two stage process. For an initially moist soil, evaporation is first climate limited, but later it becomes soil limited. During the latter stage, the evaporation rate is termed evaporability, and mathematically it is inversely proportional to the evaporation deficit. A functional approximation of the moisture distribution within the soil column is also included in the model. The model was tested using data from four experiments conducted near Phoenix, Arizona; and there was excellent agreement between the simulated and observed evaporation. The model also predicted the time of transition to the soil limited stage reasonably well. For one of the experiments, a third stage of evaporation, when vapor diffusion predominates, was observed. The occurrence of this stage was related to the decrease in moisture at the surface of the soil. The continuous similarity model does not account for vapor flow. The results show that climate, through the potential evaporation rate, has a strong influence on the time of transition to the soil limited stage. After this transition, however, bulk evaporation is independent of climate until the effects of vapor flow within the soil predominate.

Sugar palm (Argena pinnata). Potential of sugar palm for bio-ethanol production

NARCIS (Netherlands)

Elbersen, H.W.; Oyen, L.P.A.

2010-01-01

The energetic and economic feasibility of bioethanol production from sugar palm is virtually unknown. A positive factor are the potentially very high yields while the long non-productive juvenile phase and the high labor needs can be seen as problematic. Expansion to large scale sugar palm

Indian Americans at Mille Lacs.

Science.gov (United States)

Holbert, Victoria L.; And Others

The Training Center for Community Programs prepared a report on the Mille Lacs (Chippewa) Reservation in Minnesota. Data for the report were from 2 separate sources: a survey conducted by the Training Center with the assistance of the Mille Lacs community action program (1967) and an attitudinal survey conducted by Victoria Holbert during 1969.…

Lattice-Boltzmann simulations of droplet evaporation

KAUST Repository

Ledesma-Aguilar, Rodrigo; Vella, Dominic; Yeomans, Julia M.

2014-01-01

© the Partner Organisations 2014. We study the utility and validity of lattice-Boltzmann (LB) simulations to explore droplet evaporation driven by a concentration gradient. Using a binary-fluid lattice-Boltzmann algorithm based on Cahn-Hilliard dynamics, we study the evaporation of planar films and 3D sessile droplets from smooth solid surfaces. Our results show that LB simulations accurately reproduce the classical regime of quasi-static dynamics. Beyond this limit, we show that the algorithm can be used to explore regimes where the evaporative and diffusive timescales are not widely separated, and to include the effect of boundaries of prescribed driving concentration. We illustrate the method by considering the evaporation of a droplet from a solid surface that is chemically patterned with hydrophilic and hydrophobic stripes. This journal is

Lattice-Boltzmann simulations of droplet evaporation

KAUST Repository

Ledesma-Aguilar, Rodrigo

2014-09-04

© the Partner Organisations 2014. We study the utility and validity of lattice-Boltzmann (LB) simulations to explore droplet evaporation driven by a concentration gradient. Using a binary-fluid lattice-Boltzmann algorithm based on Cahn-Hilliard dynamics, we study the evaporation of planar films and 3D sessile droplets from smooth solid surfaces. Our results show that LB simulations accurately reproduce the classical regime of quasi-static dynamics. Beyond this limit, we show that the algorithm can be used to explore regimes where the evaporative and diffusive timescales are not widely separated, and to include the effect of boundaries of prescribed driving concentration. We illustrate the method by considering the evaporation of a droplet from a solid surface that is chemically patterned with hydrophilic and hydrophobic stripes. This journal is

Ground beetle populations near a kraft mill

Energy Technology Data Exchange (ETDEWEB)

Freitag, R.; Hastings, L.; Mercer, W.R.; Smith, A.

1973-02-01

Twenty species of ground beetles (Family Carabidae) and one species of carrion beetle (Family Silphidae) were collected in six stations east of a kraft paper mill in Thunder Bay, Ontario, from May to August, 1971. The beetle population decreased markedly towards the mill. There was no apparent statistical difference in size variation of specimens near the mill and those further away.

21 CFR 515.10 - Medicated feed mill license applications.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Medicated feed mill license applications. 515.10... (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS MEDICATED FEED MILL LICENSE Applications § 515.10 Medicated feed mill license applications. (a) Medicated feed mill license applications (Forms FDA 3448) may...

High temperature evaporation of titanium, zirconium and hafnium carbides

International Nuclear Information System (INIS)

Gusev, A.I.; Rempel', A.A.

1991-01-01

Evaporation of cubic nonstoichiometric carbides of titanium, zirconium and hafnium in a comparatively low-temperature interval (1800-2700) with detailed crystallochemical sample certification is studied. Titanium carbide is characterized by the maximum evaporation rate: at T>2300 K it loses 3% of sample mass during an hour and at T>2400 K titanium carbide evaporation becomes extremely rapid. Zirconium and hafnium carbide evaporation rates are several times lower than titanium carbide evaporation rates at similar temperatures. Partial pressures of metals and carbon over the carbides studied are calculated on the base of evaporation rates

Spacesuit Evaporator-Absorber-Radiator (SEAR)

Science.gov (United States)

Hodgson, Ed; Izenson, Mike; Chan, Weibo; Bue, Grant C.

2012-01-01

For decades advanced spacesuit developers have pursued a regenerable, robust nonventing system for heat rejection. Toward this end, this paper investigates linking together two previously developed technologies, namely NASA s Spacesuit Water Membrane Evaporator (SWME), and Creare s Lithium Chloride Absorber Radiator (LCAR). Heat from a liquid cooled garment is transported to SWME that provides cooling through evaporation. This water vapor is then captured by solid LiCl in the LCAR with a high enthalpy of absorption, resulting in sufficient temperature lift to reject heat to space by radiation. After the sortie, the LCAR would be heated up and dried in a regenerator to drive off and recover the absorbed evaporant. A engineering development prototype was built and tested in vacuum conditions at a sink temperature of 250 K. The LCAR was able to stably reject 75 W over a 7-hour period. A conceptual design of a full-scale radiator is proposed. Excess heat rejection above 240 W would be accomplished through venting of the evaporant. Loop closure rates were predicted for various exploration environment scenarios.

Fundamentals of evaporation and condensation phenomena

International Nuclear Information System (INIS)

Munir, Z.A.

1979-01-01

Fundamental relationships governing evaporation and condensation processes are reviewed. The terrace-ledge-kink (TLK) model is discussed in terms of atomic steps comprising growth and evaporation of crystals. Recent results in the field are described

High-energy ball milling of powder B-C mixtures

International Nuclear Information System (INIS)

Ramos, Alfeu S.; Taguchi, Simone P.; Ramos, Erika C.T.; Arantes, Vera L.; Ribeiro, Sebastiao

2006-01-01

The present work reports on the preparation of B-10 at.% C and B-18 at.% C powders by high-energy ball milling and further heat treatment. The milling process was carried out in a planetary ball mill. Following the milling process, powder samples were heat-treated at 1200 deg. C for 4 h using inert atmosphere. The milled and heat-treated B-10C and B-18C powders were characterized by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. A reduction on the intensity of B and C peaks was noticed after milling for 2 h, probably due the fine powder particle sizes because the pronounced fracture mechanism during ball milling of brittle starting components. The XRD patterns of B-10C and B-18C powders milled for 6 h indicated the presence of other peaks, suggesting that a metastable structure could have been formed. After milling for 90 h, these unknown peaks were still present. A large amount of B 4 C was formed after heat treatment at 1200 deg. C for 4 h beside these unknown peaks

The yang mills gravity dual

International Nuclear Information System (INIS)

Crooks, David E.; Evans, Nick

2003-01-01

We describe a ten dimensional supergravity geometry which is dual to a gauge theory that is non-supersymmetric Yang Mills in the infra-red but reverts to N=4 super Yang Mills in the ultra-violet. A brane probe of the geometry shows that the scalar potential of the gauge theory is stable. We discuss the infra-red behaviour of the solution. The geometry describes a Schroedinger equation potential that determines the glueball spectrum of the theory; there is a mass gap and a discrete spectrum. The glueball mass predictions match previous AdS/CFT Correspondence computations in the non-supersymmetric Yang Mills theory, and lattice data, at the 10% level. (author)

A rapid method for simultaneous quantification of 13 sugars and sugar alcohols in food products by UPLC-ELSD.

Science.gov (United States)

Koh, Dong-Wan; Park, Jae-Woong; Lim, Jung-Hoon; Yea, Myeong-Jai; Bang, Dae-Young

2018-02-01

A novel, rapid, simultaneous analysis method for five sugars (fructose, glucose, sucrose, maltose, and lactose) and eight sugar alcohols (erythritol, xylitol, sorbitol, mannitol, inositol, maltitol, lactitol, and isomalt) was developed using UPLC-ELSD, without derivatization. The analysis conditions, including the gradient conditions, modifier concentration and column length, were optimized. Thirteen sugars and sugar alcohols were separated well and the resolution of their peaks was above 1.0. Their optimum analysis condition can be analyzed within 15min. Standard curves for sugars and sugar alcohols with concentrations of 5.0-0.1% and 2.0-0.05% are presented herein, and their correlation coefficients are found to be above 0.999 and the limit of detection (LOD) was around 0.006-0.018%. This novel analysis system can be used for foodstuffs such as candy, chewing gum, jelly, chocolate, processed chocolate products, and snacks containing 0.21-46.41% of sugars and sugar alcohols. Copyright © 2017 Elsevier Ltd. All rights reserved.

Performance of evaporative condensers

Energy Technology Data Exchange (ETDEWEB)

Ettouney, Hisham M.; El-Dessouky, Hisham T.; Bouhamra, Walid; Al-Azmi, Bader

2001-07-01

Experimental investigation is conducted to study the performance of evaporative condensers/coolers. The analysis includes development of correlations for the external heat transfer coefficient and the system efficiency. The evaporative condenser includes two finned-tube heat exchangers. The system is designed to allow for operation of a single condenser, two condensers in parallel, and two condensers in series. The analysis is performed as a function of the water-to-air mass flow rate ratio (L/G) and the steam temperature. Also, comparison is made between the performance of the evaporative condenser and same device as an air-cooled condenser. Analysis of the collected data shows that the system efficiency increases at lower L/G ratios and higher steam temperatures. The system efficiency for various configurations for the evaporative condenser varies between 97% and 99%. Lower efficiencies are obtained for the air-cooled condenser, with values between 88% and 92%. The highest efficiency is found for the two condensers in series, followed by two condensers in parallel and then the single condenser. The parallel condenser configuration can handle a larger amount of inlet steam and can provide the required system efficiency and degree of subcooling. The correlation for the system efficiency gives a simple tool for preliminary system design. The correlation developed for the external heat transfer coefficient is found to be consistent with the available literature data. (Author)

Biogas from sugar beet press pulp as substitute of fossil fuel in sugar beet factories.

Science.gov (United States)

Brooks, L; Parravicini, V; Svardal, K; Kroiss, H; Prendl, L

2008-01-01

Sugar beet press pulp (SBP) accumulates as a by-product in sugar factories and it is generally silaged or dried to be used as animal food. Rising energy prices and the opening of the European Union sugar market has put pressure on the manufacturers to find alternatives for energy supply. The aim of this project was to develop a technology in the treatment of SBP that would lead to savings in energy consumption and would provide a more competitive sugar production from sugar beets. These goals were met by the anaerobic digestion of SBP for biogas production. Lab-scale experiments confirmed the suitability of SBP as substrate for anaerobic bacteria. Pilot-scale experiments focused on process optimization and procedures for a quick start up and operational control. Both single-stage and two-stage process configurations showed similar removal efficiency. A stable biogas production could be achieved in single-stage at a maximum volumetric loading rate of 10 kgCSB/(m(3) x d). Degradation efficiency was 75% for VS and 72% for COD. Average specific gas production reached 530 NL/kgCOD(SBP) or 610 NL/kgVS(SBP). (CH(4): 50 to 53%). The first large-scale biogas plant was put into operation during the sugar processing period 2007 at a Hungarian sugar factory. Digesting approximately 50% of the SBP (800 t/d, 22%TS), the biogas produced could substitute about 40% of the natural gas required for the thermal energy supply within the sugar processing. Copyright IWA Publishing 2008.

IMPROVED BIOREFINERY FOR THE PRODUCTION OF ETHANOL, CHEMICALS, ANIMAL FEED AND BIOMATERIALS FROM SUGAR CANE

Energy Technology Data Exchange (ETDEWEB)

Dr. Donal F. Day

2009-01-29

/fermentation process yielded improvements beyond what was expected solely from the addition of sugar. In order to expand the economic potential for building a biorefinery, the conversion of enzyme hydrolysates of AFEX-treated bagasse to succinic acid was also investigated. This program established a solid basis for pre-treatment of bagasse in a manner that is feasible for producing ethanol at raw sugar mills.

Reactive-inspired ball-milling synthesis of an ODS steel: study of the influence of ball-milling and annealing

International Nuclear Information System (INIS)

Brocq, M.

2010-10-01

In the context of the development of new ODS (Oxide Dispersion Strengthened) steels as core materials in future nuclear reactors, we investigated a new process inspired by reactive ball-milling which consists in using YFe 3 andFe 2 O 3 as starting reactants instead of Y 2 O 3 to produce a dispersion of nano-oxides in a steel matrix and the influence of synthesis conditions on the nano-oxide characteristics were studied. For that aim, ODS steels were prepared by ball-milling and then annealed. Multi-scale characterizations were performed after each synthesis step, using notably atom probe tomography and small angle neutron scattering. The process inspired by reactive ball-milling was shown to be efficient for ODS steel synthesis, but it does not modify the nano-oxide characteristics as compared to those of oxides directly incorporated in the matrix by ball-milling. Broadly speaking, the nature of the starting oxygen bearing reactants has no influence on nano-oxide formation. Moreover, we showed that the nucleation of nano-oxides nucleation can start during milling and continues during annealing with a very fast kinetic. The final characteristics of nano-oxides formed in this way can be monitored through ball-milling parameters (intensity, temperature and atmosphere) and annealing parameters (duration and temperature). (author)

STUDI EKSPERIMENTAL FALLING FILM EVAPORATOR PADA EVAPORASI NIRA KENTAL

Directory of Open Access Journals (Sweden)

Medya Ayunda Fitri

2016-06-01

Full Text Available Falling film evaporator is a constructed equipment for concentrating dilute solution that are sensitive to heat flowing form a thin film. This research aims to study the evaporation of cane juice concentrated with air flow on falling film evaporator and knowing evaporation rate occured in falling film evaporator used. In the process, cane juice from plant pumped to the falling film evaporator that used in this experiment. This research used concentrated cane juice and air flow rate for variables of this experiment. Cane juice flow from top of evaporator through distributor to form thin film and air flow from the bottom of evaporator. After that, temperatur of pipe wall, inlet and outlet temperature of cane juice and air were measured. This experiment concluded that the highest concentration of outlet solution is 59 brix for liquid flow rate 154 l/h and air flow rate 10 m3/h, and the other hand inlet solution concentration 51 brix. Optimum evaporation rate is 35 kg/m2.h for 51 brix and air flow rate 10 m3/h.

The Effect of Sugarcane Bagassès Size on the Properties of Pretreatment and Enzymatic Hydrolysis

Science.gov (United States)

Xu, Jun; Zhou, Guoqiang; Li, Jun

2017-06-01

The influence of milled bagasse particle size on their reducing sugar and lignin content during dilute acid hydrolysis followed by enzymolysis was investigated. The biomass crystal structures of hydrolyzed residues and enzymolyzed substrates were studied with X-ray diffractometry (XRD). The results showed that the conversion ratio of reducing sugar declined with decreasing milled bagasse particle size. The conversion ratio of reducing sugar after acid hydrolysis decreased from 31.3% to 28.9%. The smaller of the milled bagasse particle size was, the higher of the klason lignin content of hydrolyzed residuals was, which resulted in a decline in conversion ratio of reducing sugar during enzymolysis. In this study, the optimal size of milled bagasse particles was 10 to 20 meshes. The total reducing sugar conversion ratio was 61.5%, consisting of 31.3% in hydrolysis and 30.2% in enzymolysis. After hydrolysis, the specific surface area and pore size increased, and the fiber length was shortened. The inner microfiber bundles were exposed, which improved the accessibility of cellulase and the efficiency of enzymolysis.

Acceptance of sugar reduction in flavored yogurt.

Science.gov (United States)

Chollet, M; Gille, D; Schmid, A; Walther, B; Piccinali, P

2013-09-01

To investigate what level of sugar reduction is accepted in flavored yogurt, we conducted a hedonic test focusing on the degree of liking of the products and on optimal sweetness and aroma levels. For both flavorings (strawberry and coffee), consumers preferred yogurt containing 10% added sugar. However, yogurt containing 7% added sugar was also acceptable. On the just-about-right scale, yogurt containing 10% sugar was more often described as too sweet compared with yogurt containing 7% sugar. On the other hand, the sweetness and aroma intensity for yogurt containing 5% sugar was judged as too low. A second test was conducted to determine the effect of flavoring concentration on the acceptance of yogurt containing 7% sugar. Yogurts containing the highest concentrations of flavoring (11% strawberry, 0.75% coffee) were less appreciated. Additionally, the largest percentage of consumers perceived these yogurts as "not sweet enough." These results indicate that consumers would accept flavored yogurts with 7% added sugar instead of 10%, but 5% sugar would be too low. Additionally, an increase in flavor concentration is undesirable for yogurt containing 7% added sugar. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Unique anthranilic acid chemistry facilitates profiling and characterization of Ser/Thr-linked sugar chains following hydrazinolysis.

Science.gov (United States)

Anumula, Kalyan Rao

2008-02-01

A novel method for the analysis of Ser/Thr-linked sugar chains was made possible by the virtue of unique anthranilic acid (AA, 2-aminobenzoic acid [2AA]) chemistry for labeling carbohydrates in aqueous salt solutions (K. R. Anumula, Anal. Biochem. 350 (2006) 1-23). The protocol for profiling of Ser/Thr carbohydrates by hydrazinolysis was made simple by eliminating intermediary isolation steps involved in a sample preparation such as desalting and various chromatographic purification schemes. A 6-h hydrazinolysis was carried out at 60 degrees C for O-linked oligosaccharides and at 95 degrees C for total oligosaccharides (N-linked with some O-linked). Following evaporation of hydrazine (<10 min), the oligosaccharides were N-acetylated and derivatized with AA in the same reaction mixture containing salts. Presumably, the glycosyl-hydrazines/hydrazones present in the mixture did not interfere with AA labeling. Because AA is the most fluorescent and highly reactive tag for labeling carbohydrates, the procedures described are suitable for the analysis of a limited amount of samples ( approximately 5 microg) by the current high-resolution high-performance liquid chromatography (HPLC) methods. HPLC conditions developed for the separation of O-linked sugar chains based on size on an amide column were satisfactory for quantitative profiling and characterization. Common O-linked sugar chains found in fetuin, equine chorionic gonadotropin, and glycophorin can be analyzed in less than 50 min. In addition, these fast profiling methods were comparable to profiling by PNGase F (peptide N-glycosidase from Flavobacterium meningosepticum) digestion in terms of time, effort, and simplicity and also were highly reproducible for routine testing. The procedures for the release of sugar chains by hydrazinolysis at the microgram level, labeling with fluorescent tag AA, and profiling by HPLC should be useful in characterization of carbohydrates found in glycoproteins.

Evaporative water loss, relative water economy and evaporative partitioning of a heterothermic marsupial, the monito del monte (Dromiciops gliroides).

Science.gov (United States)

Withers, Philip C; Cooper, Christine E; Nespolo, Roberto F

2012-08-15

We examine here evaporative water loss, economy and partitioning at ambient temperatures from 14 to 33°C for the monito del monte (Dromiciops gliroides), a microbiotheriid marsupial found only in temperate rainforests of Chile. The monito's standard evaporative water loss (2.58 mg g(-1) h(-1) at 30°C) was typical for a marsupial of its body mass and phylogenetic position. Evaporative water loss was independent of air temperature below thermoneutrality, but enhanced evaporative water loss and hyperthermia were the primary thermal responses above the thermoneutral zone. Non-invasive partitioning of total evaporative water loss indicated that respiratory loss accounted for 59-77% of the total, with no change in respiratory loss with ambient temperature, but a small change in cutaneous loss below thermoneutrality and an increase in cutaneous loss in and above thermoneutrality. Relative water economy (metabolic water production/evaporative water loss) increased at low ambient temperatures, with a point of relative water economy of 15.4°C. Thermolability had little effect on relative water economy, but conferred substantial energy savings at low ambient temperatures. Torpor reduced total evaporative water loss to as little as 21% of normothermic values, but relative water economy during torpor was poor even at low ambient temperatures because of the relatively greater reduction in metabolic water production than in evaporative water loss. The poor water economy of the monito during torpor suggests that negative water balance may explain why hibernators periodically arouse to normothermia, to obtain water by drinking or via an improved water economy.

Uranium mill tailings remedial action technology

International Nuclear Information System (INIS)

Hartley, J.N.; Gee, G.W.

1984-01-01

The uranium milling process involves the hydrometallurgical extraction of uranium from ores and the resultant generation of large quantities of waste referred to as tailings. Uranium mill tailings have been identified as requiring remediation because they contain residual radioactive material that is not removed in the milling process. Potential radiation exposure can result from direct contact with the tailings, from radon gas emitted by the tailings, and from radioactive contamination of groundwater. As a result, the technology developed under the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action Project (UMTRAP) and the US Nuclear Regulatory Commission (NRC) Uranium Recovery Program have focused on radon control, groundwater contamination and the long-term protection of the containment system. This paper briefly summarizes the UMTRAP and NRC remedial action technology development. 33 references, 9 figures, 5 tables

Uranium mill tailings