Sample records for submerged gravel scrubber


    Energy Technology Data Exchange (ETDEWEB)



    Four large-scale air cleaning tests (AC7 - AC10) were performed in the Containment Systems Test Facility (CS'lF) to demonstrate the performance of a Submerged Gravel Scrubber for cleaning the effluent gas from a vented and purged breeder reactor containment vessel. The test article, comprised of a Submerged Gravel Scrubber (SGS) followed by a high efficiency fiber demister, had a design gas flow rate of 0.47 m{sup 3}/s (1000 ft{sup 3}/min) at a pressure drop of 9.0 kPa (36 in. H{sub 2}O). The test aerosol was sodium oxide, sodium hydroxide, or sodium carbonate generated in the 850-m{sup 3} CSTF vessel by continuously spraying sodium into the air-filled vessel while adding steam or carbon dioxide. Approximately 4500 kg (10,000 lb) of sodium was sprayed over a total period of 100 h during the tests. The SGS/Demister system was shown to be highly efficient (removing ~99.98% of the entering sodium aerosol mass), had a high mass loading capacity, and operated in a passive manner, with no electrical requirement. Models for predicting aerosol capture, gas cooling, and pressure drop are developed and compared with experimental results.

  2. Supporting Calculations For Submerged Bed Scrubber Condensate Disposal Preconceptual Study

    Energy Technology Data Exchange (ETDEWEB)

    Pajunen, A. J.; Tedeschi, A. R.


    This document provides supporting calculations for the preparation of the Submerged Bed Scrubber Condensate Disposal Preconceptual Study report The supporting calculations include equipment sizing, Hazard Category determination, and LAW Melter Decontamination Factor Adjustments.

  3. Iodine Removal Efficiency in Non-Submerged and Submerged Self-Priming Venturi Scrubber

    Energy Technology Data Exchange (ETDEWEB)

    Ali, Majid; Yan, Changqi; Sun, Zhongning; Gu, Haifeng; Wang, Junlong; Mehboob; Khurram [Harbin Engineering Univ., Harbin (China)


    The objective of this conducted research is to study the iodine removal efficiency in a self-priming venturi scrubber for submerged and non-submerged operating conditions experimentally and theoretically. The alkaline solution is used as an absorbent, which is prepared by dissolving sodium hydroxide (NaOH) and sodium thiosulphate (Na{sub 2}S{sub 2}O{sub 3}) in water to remove the gaseous iodine (I{sub 2}) from the gas. Iodine removal efficiency is examined at various gas flow rates and inlet concentrations of iodine for submerged and non-submerged operating conditions. In the non-submerged venturi scrubber, only the droplets take part in iodine removal efficiency. However, in a submerged venturi scrubber condition, the iodine gas is absorbed from gas to droplets inside the venturi scrubber and from bubbles to surrounding liquid at the outlet of a venturi scrubber. Experimentally, it is observed that the iodine removal efficiency is greater in the submerged venturi scrubber as compare to a non-submerged venturi scrubber condition. The highest iodine removal efficiency of 0.99±0.001 has been achieved in a submerged self-priming venturi scrubber condition. A mathematical correlation is used to predict the theoretical iodine removal efficiency in submerged and non-submerged conditions, and it is compared against the experimental results. The Wilkinson et al. correlation is used to predict the bubble diameter theoretically whereas the Nukiyama and Tanasawa correlation is used for droplet diameter. The mass transfer coefficient for the gas phase is calculated from the Steinberger and Treybal correlation. The calculated results for a submerged venturi scrubber agree well with experimental results but underpredicts in the case of the non-submerged venturi scrubber.


    Directory of Open Access Journals (Sweden)



    Full Text Available The objective of this conducted research is to study the iodine removal efficiency in a self-priming venturi scrubber for submerged and non-submerged operating conditions experimentally and theoretically. The alkaline solution is used as an absorbent, which is prepared by dissolving sodium hydroxide (NaOH and sodium thiosulphate (Na2S2O3 in water to remove the gaseous iodine (I2 from the gas. Iodine removal efficiency is examined at various gas flow rates and inlet concentrations of iodine for submerged and non-submerged operating conditions. In the non-submerged venturi scrubber, only the droplets take part in iodine removal efficiency. However, in a submerged venturi scrubber condition, the iodine gas is absorbed from gas to droplets inside the venturi scrubber and from bubbles to surrounding liquid at the outlet of a venturi scrubber. Experimentally, it is observed that the iodine removal efficiency is greater in the submerged venturi scrubber as compare to a non-submerged venturi scrubber condition. The highest iodine removal efficiency of 0.99±0.001 has been achieved in a submerged self-priming venturi scrubber condition. A mathematical correlation is used to predict the theoretical iodine removal efficiency in submerged and non-submerged conditions, and it is compared against the experimental results. The Wilkinson et al. correlation is used to predict the bubble diameter theoretically whereas the Nukiyama and Tanasawa correlation is used for droplet diameter. The mass transfer coefficient for the gas phase is calculated from the Steinberger and Treybal correlation. The calculated results for a submerged venturi scrubber agree well with experimental results but underpredicts in the case of the non-submerged venturi scrubber.





    The objective of this conducted research is to study the iodine removal efficiency in a self-priming venturi scrubber for submerged and non-submerged operating conditions experimentally and theoretically. The alkaline solution is used as an absorbent, which is prepared by dissolving sodium hydroxide (NaOH) and sodium thiosulphate (Na2S2O3) in water to remove the gaseous iodine (I2) from the gas. Iodine removal efficiency is examined at various gas flow rates and inlet concentrations of iodine...

  6. Wall-Friction Support of Vertical Loads in Submerged Sand and Gravel Columns

    Energy Technology Data Exchange (ETDEWEB)

    Walton, O. R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Vollmer, H. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hepa, V. S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)


    Laboratory studies of the ‘floor-loads’ under submerged vertical columns of sand and/or gravel indicate that such loads can be approximated by a buoyancy-corrected Janssen-silo-theory-like relationship. Similar to conditions in storage silos filled with dry granular solids, most of the weight of the sand or gravel is supported by wall friction forces. Laboratory measurements of the loads on the floor at the base of the water-filled columns (up to 25-diameters tall) indicate that the extra floor-load from the addition of the granular solid never exceeded the load that would exist under an unsupported (wide) bed of submerged sand or gravel that has a total depth corresponding to only two column-diameters. The measured floorloads reached an asymptotic maximum value when the depth of granular material in the columns was only three or four pipe-diameters, and never increased further as the columns were filled to the top (e.g. up to heights of 10 to 25 diameters). The floor-loads were stable and remained the same for days after filling. Aggressive tapping (e.g. hitting the containing pipe on the outside, manually with a wrench up and down the height and around the circumference) could increase (and occasionally decrease) the floor load substantially, but there was no sudden collapse or slumping to a state without significant wall friction effects. Considerable effort was required, repeatedly tapping over almost the entire column wall periphery, in order to produce floor-loads that corresponded to the total buoyancy-corrected weight of granular material added to the columns. Projecting the observed laboratory behavior to field conditions would imply that a stable floor-load condition, with only a slightly higher total floor pressure than the preexisting hydrostatic-head, would exist after a water-filled bore-hole is filled with sand or gravel. Significant seismic vibration (either a large nearby event or many micro-seismic events over an extended period) would likely

  7. Exhaust Gas Scrubber Washwater Effluent (United States)


    10 Sulfur Content of Certain Liquid Fuels Exhaust Gas Scrubber Washwater Effluent...diesel and gasoline components DIN Dissolved inorganic nitrogen THC Total hydrocarbon TKN Total Kjeldahl nitrogen HEM Hexane extractable...Benefit Analysis to support the impact assessment accompanying the revision of Directive 1999/32/EC on the sulfur content of certain liquid fuels

  8. Gravel pit lakes in Denmark: Chemical and biological state. (United States)

    Søndergaard, Martin; Lauridsen, Torben L; Johansson, Liselotte S; Jeppesen, Erik


    Mining of gravel and sand for construction purposes is big business and gravel pit lakes have become increasingly common all over the world. In Denmark, hundreds of gravel pit lakes have been created during the past decades. We investigated the chemical and biological status of 33-52 gravel pit lakes and compared the results with data from similar-sized natural Danish lakes. The area of the lakes ranged from 0.2 to 13ha and their age from 0.5 to 26years. Generally, the gravel pit lakes were clear with low nutrient concentrations, the median concentrations of total phosphorus and total nitrogen being 0.023mg/l and 0.30mg/l compared with 0.115mg/l and 1.29mg/l, respectively, in natural lakes. Correspondingly, median chlorophyll a was 5μg/l in the gravel pit lakes and 36μg/l in the natural lakes. Submerged macrophytes were found in all gravel pit lakes, with particularly high cover in the shallow ones. Most gravel pit lakes were deeper than the natural lakes, which may restrict the area potentially to be covered by submerged macrophytes, with implications also for the biological quality of the lakes. Fish were found in most of the gravel pit lakes, roach (Rutilus rutilus), perch (Perca fluviatilis) and rudd (Scardinius erythrophalmus) being the most frequently observed species. Fish stocking was common and included also non-native species such as carp (Cyprinus carpio) and rainbow trout (Oncorchynchus mykiss). Compared with the natural lakes, fish species richness and catch per gillnet were overall lower in the gravel pit lakes. Groundwater-fed gravel pit lakes add importantly to the number of high-quality lakes in Denmark and with an optimised design and by avoiding negative side effects, they can be positive for both nature and society. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Industrial sand and gravel (United States)

    Dolley, T.P.


    Domestic production of industrial sand and gravel in 2012 was about 49.5 Mt (55 million st), increasing 13 percent compared with that of 2011. Some important end uses for industrial sand and gravel include abrasives, filtration, foundry, glassmaking, hydraulic fracturing sand (frac sand) and silicon metal applications.


    Papanicolaou, T.; Tsakiris, A. G.; Kramer, C. M.


    The overarching objective of this investigation was to evaluate the role of relative submergence on the formation and evolution of cluster microforms in gravel bed streams and its implications to bedload transport. Secondary objectives of this research included (1) a detailed analysis of mean flow measurements around a clast; and (2) a selected number of experimental runs where the mean flow characteristics are linked together with the bed micro-topography observations around a clast. It is hypothesized that the relative submergence is an important parameter in defining the feedback processes between the flow and clasts, which governs the flow patterns around the clasts, thus directly affecting the depositional patterns of the incoming sediments. To examine the validity of the hypothesis and meet the objectives of this research, 19 detailed experimental runs were conducted in a tilting, water recirculating laboratory flume under well-controlled conditions. A fixed array of clast-obstacles were placed atop a well-packed bed with uniform size glass beads. During the runs, multifractional spherical particles were fed upstream of the clast section at a predetermined rate. State-of-the-art techniques/instruments, such as imaging analysis software, Large Scale Particle Velocimeter (LSPIV) and an Acoustic Doppler Velocimetry (ADV) were employed to provide unique quantitative measurements for bedload fluxes, clast/clusters geomorphic patterns, and mean flow characteristics in the vicinity of the clusters. Different flow patterns were recorded for the high relative submergence (HRS) and low relative submergence (LRS) experimental runs. The ADV measurements provided improved insight about the governing flow mechanisms for the HRS runs. These mechanisms were described with flow upwelling at the center of the flume and downwelling occurring along the flume walls. Flow downwelling corresponded to an increase in the free surface velocity. Additionally, the visual observations

  11. Sand and Gravel Deposits (United States)

    Vermont Center for Geographic Information — This dataset is a statewide polygon coverage of sand, gravel, and stone resources. This database includes the best data available from the VT Agency of Natural...

  12. The Dynamics of Aerosols in Condensational Scrubbers

    DEFF Research Database (Denmark)

    Johannessen, Jens Tue; Christensen, Jan A.; Simonsen, Ole


    A mathematical model for the simulation of the dynamics of aerosol change in condensational scrubbers and scrubbing condensers is proposed. The model is applicable for packed column gas/liquid contact when plug flow can be assumed. The model is compared with experimental data for particle removal...... in a pilot plant condensational scrubber. The model can satisfactorily predict particle growth and particle deposition by diffusional, convective and inertial mechanisms for a wide range of conditions. The parameters of principal importance for the model precision are identified and a procedure...... for their estimation is proposed. The behaviour of scrubbers and condensers for some important technical applications is demonstrated by model simulations. (C) 1997 Elsevier Science Ltd....

  13. Low density gravel substitute gravel pack in Marlim

    Energy Technology Data Exchange (ETDEWEB)

    Albino, E.


    Successful gravel pack completion means optimization of production. This has been PETROBRAS` task regarding completion of the giant Marlim field. Significant improvement have been noticed recently with the introduction of techniques such as horizontal drilling, frac pack and low density gravel substitute gravel pack. This paper discusses the introduction and results of the system, its advantages and trends since this technique can become an excellent alternative when a more aggressive technique is no economical. (author). 5 refs., 4 figs.

  14. Smoke cleaning in small straw boilers. Venturi scrubber; Roegrensning paa mindre halmkedler. Venturi-scrubber

    Energy Technology Data Exchange (ETDEWEB)

    Kristensen, J.K.; Keller, P. [Statens Husdyrbrugsforsoeg, Afd. for Bygningsteknik (Denmark); Germann, L. [Dansk Teknologisk Institut (Denmark)


    In 1993-94 the National Institute of Agricultural engineering (SjF, Denmark) developed a scrubber which worked on the Venturi principle. Dust emission reductions of 85-90% could be achieved in an automatically charged straw boiler. Water is added, while the velocity of flue gas inside the scrubber increases to 50-90 m/s. At a fan pressure of 7.5 kPa and a dust content of 600 mg/m{sup 3}{sub n} in the smoke an efficiency of 70% can be achieved. For a smoke quantity of 250 m{sup 3}/h, which is equivalent to a charged effect of 100 kW, it has not been possible to find a fan with an efficiency higher than about 25% at a pressure of 7.5 kPa. The power requirement of the scrubber is 2.3 kW. Standard fans have efficiencies higher than 50% and air flows that make the fans suitable for boilers of 400-800 kW, in large boilers the relative power requirement for the scrubbers can be reduced to half. Scrubbers discharge 2 l of drainage water pr. hr. hour which can profitably be conducted to a slurry tank or a cesspool. Corrosion by scrubbing water has been demonstrated around the weldings of the acid-resistant steel sheet. During operation the water in the scrubber is heated to about 55 deg. C. The heating energy generated can be exploited by using a heat exchanger, e.g. for underfloor heating etc. Scrubbers require a supply of 11 l of mains water per running hour. The efficiency of the boiler while cleaning the flue gas can be raised from 80 to more than 90%. Maintenance needs are limited. (AB)(812 refs.)

  15. Evaluation of a Zirconium Recycle Scrubber System

    Energy Technology Data Exchange (ETDEWEB)

    Spencer, Barry B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)


    A hot-cell demonstration of the zirconium recycle process is planned as part of the Materials Recovery and Waste Forms Development (MRWFD) campaign. The process treats Zircaloy® cladding recovered from used nuclear fuel with chlorine gas to recover the zirconium as volatile ZrCl4. This releases radioactive tritium trapped in the alloy, converting it to volatile tritium chloride (TCl). To meet regulatory requirements governing radioactive emissions from nuclear fuel treatment operations, the capture and retention of a portion of this TCl may be required prior to discharge of the off-gas stream to the environment. In addition to demonstrating tritium removal from a synthetic zirconium recycle off-gas stream, the recovery and quantification of tritium may refine estimates of the amount of tritium present in the Zircaloy cladding of used nuclear fuel. To support these objectives, a bubbler-type scrubber was fabricated to remove the TCl from the zirconium recycle off-gas stream. The scrubber was fabricated from glass and polymer components that are resistant to chlorine and hydrochloric acid solutions. Because of concerns that the scrubber efficiency is not quantitative, tests were performed using DCl as a stand-in to experimentally measure the scrubbing efficiency of this unit. Scrubbing efficiency was ~108% ± 3% with water as the scrubber solution. Variations were noted when 1 M NaOH scrub solution was used, values ranged from 64% to 130%. The reason for the variations is not known. It is recommended that the equipment be operated with water as the scrubbing solution. Scrubbing efficiency is estimated at 100%.

  16. US State Submerged Lands (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Submerged Lands Act (43 U.S.C. Section 1301 et seq.) grants coastal states title to natural resources located within their coastal submerged lands and navigable...

  17. On the dynamics of shallow gravel bed flow (United States)

    Mohajeri, Seyed Hossein; Righetti, Maurizio; Wharton, Geraldene; Gurnell, Angela


    Flow dynamics on a gravel bed is a popular research subject because of environmental implications and especially in the presence of sediment transport. However, some features of flow dynamics on gravel beds are not completely understood and many questions remain open, especially in the context of the turbulence structure of the flow field and sediment transport. Due to the low submergence characteristics of the flow, the dynamics of the turbulent flow field, especially at the bed region, cannot be regarded as a classical boundary roughness problem, sensu Nikuradse (Nezu and Nakagawa, 1993) due to the strong spatial and temporal variation of the flow field. Over the past decade, in order to properly take into account the spatial heterogeneity, spatial averaging of time averaged values have become common. Besides,recently a trend to understand the role of gravel bed statistical properties, such as structure function of the bed elevation, on the statistics of the near-bed flow has been proposed. Although much research considers gravel beds by spatial averaging and research has been conducted on the effects of bed characteristics on near bed flow and sediment transport, only a few studies consider both together. In the present study, the results of 2D PIV measurement coupled with high accurate measurement of the gravel bed characteristics and the turbulence properties of the low submergence gravel bed flow as related to the bed properties are presented. The double averaging method was used in the analysis. Furthermore, in order to have a better insight into the dynamics of transport processes at the bed, a simple quadrant analysis, based on the Lu and Willmarth method, was implemented (Lu and Willmarth, 1973). Finally, the turbulent integral length scale was calculated both near and far from the gravel bed. The time and double averaged results show an agreement with the previous studies. Moreover, the result of quadrant analysis shows the sweep is dominant between

  18. Gravel roads management : volume 1, gravel roads management. (United States)


    This report establishes procedures for managing dirt and gravel roads, with a primary focus on smaller agencies, such as Wyoming counties, that must manage their roads with very limited resources. The report strives, first, to guide and assist smalle...

  19. Gravel roads management : volume 2, gravel roads management : implementation guide. (United States)


    This report establishes procedures for managing dirt and gravel roads, with a primary focus on smaller agencies, such as Wyoming counties, that must manage their roads with very limited resources. The report strives, first, to guide and assist smalle...

  20. Gravel roads management : volume 3, gravel roads management : programming guide. (United States)


    This report establishes procedures for managing dirt and gravel roads, with a primary focus on smaller agencies, such as Wyoming counties, that must manage their roads with very limited resources. The report strives, first, to guide and assist smalle...

  1. (Passamaquoddy Technology Recovery Scrubber trademark , March 1992)

    Energy Technology Data Exchange (ETDEWEB)


    The Passamaquoddy Technology Recovery Scrubber{trademark} has been built and is being demonstrated on-line at the Dragon Products Plant in Thomaston, Maine. This Innovative Clean Coal Technology is using waste cement kiln dust (CKD) to scrub sulfur dioxide, some NO{sub x}, as well as a small amount of carbon dioxide from a coal burning kiln exhaust flue gas. The process also enables the cement plant to reuse the treated CKD, eliminating the need to landfill this material. Potassium, the offending contaminant in the CKD, is extracted in a useful form, potassium sulfate, which is used as a fertilizer. These useful products generate income from operation of this Recovery Scrubber. System start-up was begun in late December of 1990. At that time, several mechanical problems were encountered. These relatively minor problems were resolved enabling Phase III to begin on August 20, 1991. While inefficiencies are still being worked out, major program objectives are being met. Resolution of remaining operability problems is well in hand and should not hamper attainment of all project goals.

  2. Hydrodynamics of a Multistage Wet Scrubber Incineration Conditions (United States)

    Said, M. M.; Manyele, S. V.; Raphael, M. L.


    The objective of the study was to determine the hydrodynamics of the two stage counter-current cascade wet scrubbers used during incineration of medical waste. The dependence of the hydrodynamics on two main variables was studied: Inlet air flow rate and inlet liquid flow rate. This study introduces a new wet scrubber operating features, which are…

  3. Investing in Marine Scrubber under Uncertainty with Real Option Thinking

    DEFF Research Database (Denmark)

    Jiang, Liping; Hansen, Carsten Ørts

    works that examine the economic feasibility of scrubber retrofitting through the net present value rule, this paper applies the Real Option Analysis to find the optimal investment strategies. The proposed decision-making framework addresses the uncertainty and the value of deferral option embedded...... in the scrubber investment. The multiple sources of investment uncertainties are explicitly analyzed and integrated in the modeling by using Rainbow option. The results demonstrate that the value of the scrubber investment has significantly increased for several cases by considering the deferral option...

  4. Elemental mercury removal using a wet scrubber.

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, E.; Livengood, C. D.; Martin, K.; Mendelsohn, M. H.; Zhou, C. Q.


    Mercury (Hg) is a toxic metal that is emitted into the environment by both natural and human activities. Acute and chronic exposure to mercury and methyl mercury in humans results in central nervous system damage, kidney damage, and even death. Although some Hg emission sources have been regulated, coal-fired utilities have not been. In anticipation of federal regulations on mercury emissions from coal-fired power plants, Argonne National Laboratory (ANL) has designed a flue gas simulation system to study the removal of elemental mercury. The simulated flue gas enters the system and combines with the inlet mercury vapor (from a calibrated permeation tube), carried by nitrogen gas. This combined gas continues past the flow meter and the pressure gage to the reactor inlet. Inside the reactor chamber, the flue gas is sprayed with NOXSORB{reg_sign}, a chloric acid solution, which reacts with elemental mercury. The amount of reaction (oxidation) of elemental mercury is important since mercury in an oxidized form is highly soluble, In this form, the Hg can be picked up downstream by a wet scrubber from fossil-fuel burning utilities. Experiments on mercury removal from flue gases have been conducted at ANL, with the participation of a senior design team from Purdue University Calumet. Temperature variations ranging from room temperature to 350 F have been studied. Other parameters, such as the concentration of NOXSORB{reg_sign}, were also tested. Furthermore, pump speed and sprayer droplet sizes of the NOXSORB{reg_sign} solution were studied. A literature survey on the current and proposed mercury control legislation, along with the existing control technologies, has been performed as part of the senior design project. With guidance from ANL, an understanding of the simulation system has been developed. This information has been used to determine the mass transfer. Another literature survey was performed on the reaction kinetics of mercury. The information obtained was

  5. HWVP submerged bed scrubber waste treatment by ion exchange at high pH

    Energy Technology Data Exchange (ETDEWEB)

    Bray, L.A.; Carson, K.J.; Elovich, R.J.; Eakin, D.E.


    The Hanford Waste Vitrification Plant (HWVP) is expected to produce aqueous waste streams that will require further processing for cesium, strontium, and transuranic (TRU) removal prior to incorporation into grout. Fluor Daniel, Inc. has recommended that zeolite be added to these waste streams for adsorption of cesium (Cs) and strontium (Sr) following pH adjustment by sodium hydroxide (NAOH) addition. Filtration will then used to remove the TRU elements associated with the process solids and the zeolite containing the Cs and Sr.

  6. Numerical simulation of two-phase flow behavior in Venturi scrubber by interface tracking method

    Energy Technology Data Exchange (ETDEWEB)

    Horiguchi, Naoki, E-mail: [Japan Atomic Energy Agency, 2-4, Shirakata, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan); University of Tsukuba, 1-1-1, Tennodai, Tsukuba, Ibaraki, 305-8577 (Japan); Yoshida, Hiroyuki [Japan Atomic Energy Agency, 2-4, Shirakata, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan); Abe, Yutaka [University of Tsukuba, 1-1-1, Tennodai, Tsukuba, Ibaraki, 305-8577 (Japan)


    Highlights: • Self-priming occur because of pressure balance between inside and outside of throat is confirmed. • VS has similar flow with a Venturi tube except of disturbance and burble flow is considered. • Some of atomization simulated are validated qualitatively by comparison with previous studies. - Abstract: From the viewpoint of protecting a containment vessel of light water reactor and suppressing the diffusion of radioactive materials from a light water reactor, it is important to develop the device which allows a filtered venting of contaminated high pressure gas. In the filtered venting system that used in European reactors, so called Multi Venturi scrubbers System is used to realize filtered venting without any power supply. This system is able to define to be composed of Venturi scrubbers (VS) and a bubble column. In the VS, scrubbing of contaminated gas is promoted by both gas releases through the submerged VS and gas-liquid contact with splay flow formed by liquid suctioned through a hole provided by the pressure difference between inner and outer regions of a throat part of the VS. However, the scrubbing mechanism of the self-priming VS including effects of gas mass flow rate and shape of the VS are understood insufficiently in the previous studies. Therefore, we started numerical and experimental study to understand the detailed two-phase flow behavior in the VS. In this paper, to understand the VS operation characteristics for the filtered venting, we performed numerical simulations of two-phase flow behavior in the VS. In the first step of this study, we perform numerical simulations of supersonic flow by the TPFIT to validate the applicability of the TPFIT for high velocity flow like flow in the VS. In the second step, numerical simulation of two-phase flow behavior in the VS including self-priming phenomena. As the results, dispersed flow in the VS was reproduced in the numerical simulation, as same as the visualization experiments.

  7. Cars submerged in water.

    NARCIS (Netherlands)


    Crashes in which cars are submerged in deep water or in a ditch are often complicated and serious. Considering their severity and the fact that approximately half the fatalities in this crash type are not due to drowning but to injury, preventive measures are to be preferred above measures that have

  8. Operation Characteristics of a Venturi Scrubber with Variation of the ...

    African Journals Online (AJOL)

    Venturi scrubbers are used for the separation of solid particles from gases. With the help of this rig, it is possible to separate particles smaller than 1 μ.m in diameter , although it involves a high energy consumption. To reduce the high energy consumption the influence of different diffusor geometries upon the perfomance ...

  9. Gas absorption studies in a butterfly valve scrubber

    Energy Technology Data Exchange (ETDEWEB)

    Beg, S.A.; Taheri, M.


    Gas absorption and pressure drop in a wetted butterfly valve constituting a novel scrubber system are investigated. The exceptional suitability of the butterfly device is demonstrated by its flexibility to adjust to large variations in both gas and liquid flow rates. (1 diagram, 5 graphs, 19 references)

  10. Incipient motion of gravel and coal beds

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    Wiberg & Smith 1987; Wilcock & Southard 1988; Bridge & Bennett 1992; Wilcock 1992,. 1993; Kuhnle 1993; Patel & Ranga Raju 1999; Dey 1999; Dey et al 1999; Dey & Debnath. 2000). Furthermore, experimental studies with gravel beds were put forward by Bathust et al. (1987) and field studies with gravel and boulder ...

  11. Stabilization of gravel deposits using microorganisms

    NARCIS (Netherlands)

    Van der Star, W.R.L.; Van Wijngaarden, W.K.; Van Paassen, L.A.; Van Baalen, L.R.; Zwieten, G.


    One of the techniques used for the construction of underground infrastructure is horizontal directional drilling (HDD). This trenchless method is complicated when crossing gravel deposits as a borehole in coarse gravel tends to collapse, causing the drill pipe to get stuck or the failure of

  12. Market Opportunities for Austenitic Stainless Steels in SO2 Scrubbers (United States)

    Michels, Harold T.


    Recent U.S. federal legislation has created new opportunities for SO2 scrubbers because all coals, even low-sulfur western coals, will probably require scrubbing to remove SO2 from gaseous combustion products. Scrubbing, the chemical absorption of SO2 by vigorous contact with a slurry—usually lime or limestone—creates an aggressive acid-chloride solution. This presents a promising market for pitting-resistant austenitic stainless steels, but there is active competition from rubber and fiberglass-lined carbon steel. Since the latter are favored on a first-cost basis, stainless steels must be justified on a cost/performance or life-cost basis. Nickel-containing austenitic alloys are favored because of superior field fabricability. Ferritic stainless steels have little utility in this application because of limitations in weldability and resulting poor corrosion resistance. Inco corrosion test spools indicate that molybdenum-containing austenitic alloys are needed. The leanest alloys for this application are 316L and 317L. Low-carbon grades of stainless steel are specified to minimize corrosion in the vicinity of welds. More highly alloyed materials may be required in critical areas. At present, 16,000 MW of scrubber capacity is operational and 17,000 MW is under construction. Another 29,000 MW is planned, bringing the total to 62,000 MW. Some 160,000 MW of scrubber capacity is expected to be placed in service over the next 10 years. This could translate into a total potential market of 80,000 tons of alloy plate for new power industry construction in the next decade. Retrofitting of existing power plants plus scrubbers for other applications such as inert gas generators for oil tankers, smelters, municipal incinerators, coke ovens, the pulp and paper industry, sulfuric acid plants, and fluoride control in phosphoric acid plants will add to this large market.

  13. Removing Ambiguities of IP Telephony Traffic Using Protocol Scrubbers

    Directory of Open Access Journals (Sweden)

    Bazara I. A. Barry


    Full Text Available Network intrusion detection systems (NIDSs face the serious challenge of attacks such as insertion and evasion attacks that are caused by ambiguous network traffic. Such ambiguity comes as a result of the nature of network traffic which includes protocol implementation variations and errors alongside legitimate network traffic. Moreover, attackers can intentionally introduce further ambiguities in the traffic. Consequently, NIDSs need to be aware of these ambiguities when detection is performed and make sure to differentiate between true attacks and protocol implementation variations or errors; otherwise, detection accuracy can be affected negatively. In this paper we present the design and implementation of tools that are called protocol scrubbers whose main functionality is to remove ambiguities from network traffic before it is presented to the NIDS. The proposed protocol scrubbers are designed for session initiation and data transfer protocols in IP telephony systems. They guarantee that the traffic presented to NIDSs is unambiguous by eliminating ambiguous behaviors of protocols using well-designed protocol state machines, and walking through packet headers of protocols to make sure packets will be interpreted in the desired way by the NIDS. The experimental results shown in this paper demonstrate the good quality and applicability of the introduced scrubbers.

  14. Crossfire-Bonds Gravel Pit NPDES Permit (United States)

    This is an NPDES permit and statement of basis. The Crossfire-Bonds Gravel Pit is authorized to discharge to Deer Canyon. Authorization for discharge is limited to only those outfalls specifically listed in the permit.

  15. Optimization of submerged vane parameters

    Indian Academy of Sciences (India)

    Submerged vanes are airfoils which are in general placed at certain angle with respect to the flow direction in a channel to induce artificial circulations downstream. By virtue of these artificially generated circulations, submerged vanes were utilized to protect banks of rivers against erosion, to control shifting of rivers, to avoid ...

  16. Optimization of submerged vane parameters

    Indian Academy of Sciences (India)

    H Sharma

    velocities simulated from CFD using standard k-x model were very much in accordance with what it was measured by Wang and Odgaard [4]. Thus, model can be used to study the turbulence characteristics around submerged vanes and to predict various parameters downstream of the submerged vanes. After the model ...

  17. Submerged AUV Charging Station (United States)

    Jones, Jack A.; Chao, Yi; Curtin, Thomas


    Autonomous Underwater Vehicles (AUVs) are becoming increasingly important for military surveillance and mine detection. Most AUVs are battery powered and have limited lifetimes of a few days to a few weeks. This greatly limits the distance that AUVs can travel underwater. Using a series of submerged AUV charging stations, AUVs could travel a limited distance to the next charging station, recharge its batteries, and continue to the next charging station, thus traveling great distances in a relatively short time, similar to the Old West “Pony Express.” One solution is to use temperature differences at various depths in the ocean to produce electricity, which is then stored in a submerged battery. It is preferred to have the upper buoy submerged a reasonable distance below the surface, so as not to be seen from above and not to be inadvertently destroyed by storms or ocean going vessels. In a previous invention, a phase change material (PCM) is melted (expanded) at warm temperatures, for example, 15 °C, and frozen (contracted) at cooler temperatures, for example, 8 °C. Tubes containing the PCM, which could be paraffin such as pentadecane, would be inserted into a container filled with hydraulic oil. When the PCM is melted (expanded), it pushes the oil out into a container that is pressurized to about 3,000 psi (approx equals 20.7 MPa). When a valve is opened, the high-pressure oil passes through a hydraulic motor, which turns a generator and charges a battery. The low-pressure oil is finally reabsorbed into the PCM canister when the PCM tubes are frozen (contracted). Some of the electricity produced could be used to control an external bladder or a motor to the tether line, such that depth cycling is continued for a very long period of time. Alternatively, after the electricity is generated by the hydraulic motor, the exiting low-pressure oil from the hydraulic motor could be vented directly to an external bladder on the AUV, such that filling of the bladder

  18. Shrinkage Properties of Cement Stabilized Gravel

    DEFF Research Database (Denmark)

    Lund, Mia Schou Møller; Hansen, Kurt Kielsgaard


    Cement stabilized gravel is an attractive material in road construction because its strength prop-erties are accommodating the increasingly higher requirements to the bearing capacity of a base course. However, reflection cracking of cement stabilized gravel is a major concern. In this pa......-per the shrinkage properties of cement stabilized gravel have been documented under various temperature and relative humidity conditions. Two cement contents corresponding to a 28-days compressive strength of 6.2 MPa and 12.3 MPa have been tested and compared. It is found that the coefficient of linear expansion...... for the two cement contents is 9.9 × 10-6 ⁰C-1 and 11.3 × 10-6 ⁰C-1, respectively. Furthermore, it is found that reflecting cracking can mainly be explained by temperature dependent shrinkage rather than moisture dependent shrinkage....

  19. Submerged beachrock preservation in the context of wave ravinement (United States)

    Pretorius, Lauren; Green, Andrew N.; Andrew Cooper, J.


    This study examines a Holocene-aged submerged shoreline, Limestone Reef, located in the shallow subtidal zone of South Africa's east coast. It comprises an elongate, coast-oblique, slab-like outcrop of beachrock situated above the contemporary fair-weather wave base. It is currently undergoing mechanical disintegration. Its unique and rare preservation in a high-energy setting affords an opportunity to examine the mechanical processes occurring during wave ravinement associated with rising sea level. The submerged shoreline and the adjacent shoreface were examined using high-resolution seismic reflection, side-scan sonar and shallow-water multibeam echosounding techniques. Limestone Reef rests on top of unconsolidated Holocene deposits. The structure's surface is characterised by reef-perpendicular gullies with rubble derived from the slab fringing its seaward edge. Limestone Reef slopes gently seawards and has a steep landward-facing edge where gullies are most prominently developed. Teardrop-shaped rippled scour depressions, marked by high backscatter, are located seawards of the submerged shoreline. These elongate in a seaward direction and are filled with bioclastic gravels and residual rubble from Limestone Reef. The gullies in the upstanding structure are indicative of wave plucking and abrasion of the shoreline. The material exposed by the rippled scour depressions is identical to that comprising the postglacial ravinement surface identified in the offshore stratigraphy. These deposits are considered to represent the contemporary, actively forming wave ravinement surface. The results suggest that wave ravinement of submerged shorelines is a discontinuous process dominated by the seaward entrainment of material from its landward edge controlled by high-energy drawback during storm surges. The ravinement process appears to operate at the seasonal scale and averages out over the long-term millennial scale for the continuous surface.

  20. [Passamaquoddy Technology Recovery Scrubber{trademark}, March 1992

    Energy Technology Data Exchange (ETDEWEB)


    The Passamaquoddy Technology Recovery Scrubber{trademark} has been built and is being demonstrated on-line at the Dragon Products Plant in Thomaston, Maine. This Innovative Clean Coal Technology is using waste cement kiln dust (CKD) to scrub sulfur dioxide, some NO{sub x}, as well as a small amount of carbon dioxide from a coal burning kiln exhaust flue gas. The process also enables the cement plant to reuse the treated CKD, eliminating the need to landfill this material. Potassium, the offending contaminant in the CKD, is extracted in a useful form, potassium sulfate, which is used as a fertilizer. These useful products generate income from operation of this Recovery Scrubber. System start-up was begun in late December of 1990. At that time, several mechanical problems were encountered. These relatively minor problems were resolved enabling Phase III to begin on August 20, 1991. While inefficiencies are still being worked out, major program objectives are being met. Resolution of remaining operability problems is well in hand and should not hamper attainment of all project goals.

  1. Effectiveness of multi-stage scrubbers in reducing emissions of air pollutants from pig houses

    NARCIS (Netherlands)

    Zhao, Y.; Aarnink, A.J.A.; Jong, de M.C.M.; Ogink, N.W.M.; Groot Koerkamp, P.W.G.


    Emissions of air pollutants from livestock houses may raise environmental problems and pose hazards to public health. They can be reduced by scrubbers installed at the air outlets of livestock houses. In this study, three multi-stage scrubbers were evaluated in terms of their effectiveness in

  2. Scrubber capabilities to remove airborne microorganisms and other aerial pollutants from the exhaust air of animal houses

    NARCIS (Netherlands)

    Aarnink, A.J.A.; Landman, W.J.M.; Melse, R.W.; Zhao, Y.; Ploegaert, J.P.M.; Huynh, T.T.T.


    Two studies were conducted to assess the efficiency of air scrubbers to reduce airborne microorganisms in the exhaust air from animal houses. First, in a field study, the effects of a bio-scrubber and an acid scrubber on total bacterial counts were assessed. Higher bacterial counts were found in the

  3. Upflow gravel filtration for multiple uses

    NARCIS (Netherlands)

    Sanchez Torres, L.D.


    The use of upflow gravel filtration (UFG) is relevant for water supply systems in rural areas and small towns in Colombia, because water quality from surface sources is changing due to the deterioration of watersheds caused by deforestation, erosion, and the discharge of untreated wastewater. These

  4. Incipient motion of gravel and coal beds

    Indian Academy of Sciences (India)

    ... Shields parameter, particle Froude number, non-dimensional particle diameter and non-dimensional flow depth. Equations of critical bed shear stress for the initial movement of gravel and coal beds were obtained using experimental data. The method of application of critical bed shear stress equations is also mentioned.

  5. Compositional signatures in acoustic backscatter over vegetated and unvegetated mixed sand-gravel riverbeds (United States)

    Buscombe, Daniel; Grams, Paul E.; Kaplinski, Matt A.


    Multibeam acoustic backscatter has considerable utility for remote characterization of spatially heterogeneous bed sediment composition over vegetated and unvegetated riverbeds of mixed sand and gravel. However, the use of high-frequency, decimeter-resolution acoustic backscatter for sediment classification in shallow water is hampered by significant topographic contamination of the signal. In mixed sand-gravel riverbeds, changes in the abiotic composition of sediment (such as homogeneous sand to homogeneous gravel) tend to occur over larger spatial scales than is characteristic of small-scale bedform topography (ripples, dunes, and bars) or biota (such as vascular plants and periphyton). A two-stage method is proposed to filter out the morphological contributions to acoustic backscatter. First, the residual supragrain-scale topographic effects in acoustic backscatter with small instantaneous insonified areas, caused by ambiguity in the local (beam-to-beam) bed-sonar geometry, are removed. Then, coherent scales between high-resolution topography and backscatter are identified using cospectra, which are used to design a frequency domain filter that decomposes backscatter into the (unwanted) high-pass component associated with bedform topography (ripples, dunes, and sand waves) and vegetation, and the (desired) low-frequency component associated with the composition of sediment patches superimposed on the topography. This process strengthens relationships between backscatter and sediment composition. A probabilistic framework is presented for classifying vegetated and unvegetated substrates based on acoustic backscatter at decimeter resolution. This capability is demonstrated using data collected from diverse settings within a 386 km reach of a canyon river whose bed varies among sand, gravel, cobbles, boulders, and submerged vegetation.

  6. Compositional Signatures in Acoustic Backscatter Over Vegetated and Unvegetated Mixed Sand-Gravel Riverbeds (United States)

    Buscombe, D.; Grams, P. E.; Kaplinski, M. A.


    Multibeam acoustic backscatter has considerable utility for remote characterization of spatially heterogeneous bed sediment composition over vegetated and unvegetated riverbeds of mixed sand and gravel. However, the use of high-frequency, decimeter-resolution acoustic backscatter for sediment classification in shallow water is hampered by significant topographic contamination of the signal. In mixed sand-gravel riverbeds, changes in the abiotic composition of sediment (such as homogeneous sand to homogeneous gravel) tend to occur over larger spatial scales than is characteristic of small-scale bedform topography (ripples, dunes, and bars) or biota (such as vascular plants and periphyton). A two-stage method is proposed to filter out the morphological contributions to acoustic backscatter. First, the residual supragrain-scale topographic effects in acoustic backscatter with small instantaneous insonified areas, caused by ambiguity in the local (beam-to-beam) bed-sonar geometry, are removed. Then, coherent scales between high-resolution topography and backscatter are identified using cospectra, which are used to design a frequency domain filter that decomposes backscatter into the (unwanted) high-pass component associated with bedform topography (ripples, dunes, and sand waves) and vegetation, and the (desired) low-frequency component associated with the composition of sediment patches superimposed on the topography. This process strengthens relationships between backscatter and sediment composition. A probabilistic framework is presented for classifying vegetated and unvegetated substrates based on acoustic backscatter at decimeter resolution. This capability is demonstrated using data collected from diverse settings within a 386 km reach of a canyon river whose bed varies among sand, gravel, cobbles, boulders, and submerged vegetation.

  7. Scrubber-Integrated Wet Electrostatic Precipitator; Skrubberintegrerat vaatt elektrofilter, WESP

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Sven; Baefver, Linda; Davidsson, Kent; Pettersson, Jens; Schmidt, Hans; Strand, Michael; Yngvesson, Johan


    Combustion processes for heat and power production are an important source of sub-micron particle emissions, which cause enhanced health risks and premature deaths. To meet future requirements of economical and robust dust cleaning equipment, the Wet Electrostatic Precipitation (WESP) technology has been further developed in this project. A pilot scale slip stream WESP unit, installed by Goetaverken Miljoe, has been successfully installed and tested at the Renova Waste-to-Energy plant in Goeteborg, Sweden. The particles in the gas are charged by an ionizing electrode and collected in a concentric cylinder geometry. The WESP pilot consists of a unique combination of several existing technologies: it is integrated with a packed bed scrubber which means an ideally uniformly distributed gas flow in the WESP inlet. Furthermore, the WESP unit has a water cooled condensing collector, which facilitates continuous formation of a water film. The downward flowing water film transports the collected dust counter current to the upward flowing flue gas in order to minimize particle re-entrainment. The WESP is equipped with a high frequency transformer for stable voltage output and is fabricated in electrically conductive corrosion resistant Fibre Reinforced Plastic (FRP). The concentration of dust upstream of the WESP unit varied between 6.2 and 28 mg/Nm{sup 3} dry gas. All measured outlet dust concentrations were below 0.3 mg/Nm{sup 3} (dry gas, 11% O{sub 2}), which equals 3% of the applicable emission limit. The dust removal efficiency has been higher than 97% in all the dust measurements. The mean value of all the dust measurements was 15.2 mg/Nm{sup 3} upstream and 0.14 mg/Nm{sup 3} in downstream (both as dry gas, 11% O{sub 2}), which gives an average removal efficiency of slightly more than 99%. The removal efficiency increased with increasing inlet dust concentration, SO{sub 2} concentration and {Delta}T of the collector cooling. Chlorine, potassium, sodium, silicon and

  8. Baghouse vs. precipator for dry scrubber systems - pilot study results

    Energy Technology Data Exchange (ETDEWEB)

    Wilkinson, J.M.; Tonn, D.P.


    The first utility dry scrubber unit to be brought on line will be operating with baghouses for particulate emissions control, although precipitators have also been sold as part of dry sulfur removal (DSR) systems. There has been considerable discussion about the selection of particulate collection equipment for DSR systems and the choice between baghouse and precipitator is not always an obvious one, since overall system performnce must be reactor to supply the baghouse and precipator evaluated. The findings of an extensive testing program to investigate the performance characteristics of a pilot baghouse and pilot precipitator installed at 20 MW DSR demonstration plant are reported. Because an understanding of the interaction between the reactor and particulate collection is paramount to proper system design, both collection efficiencies and the contribution of the particulate collector to system sulfur dioxide (SO/sub 2/) removal are discussed. 6 refs.

  9. Prediction of hydrodynamic characteristics of a venturi scrubber by using CFD simulation

    Directory of Open Access Journals (Sweden)

    Manisha Bal


    Full Text Available The filtered containment venting system (FCVS is a safety relevant system, which consists of venturi scrubber and a mesh filter. FCVS needs to be further assessed to improve the existing performance of the venturi scrubber. Therefore, hydrodynamics is an important counter-component needs to be investigated to improve the design of the venturi scrubber. In the present research, Computational Fluid Dynamic (CFD has been used to predict the hydrodynamic behaviour of a newly designed venturi scrubber. Mesh was developed by gambit 2.4.6 and ansys fluent 15 has been used to predict the pressure drop profile inside the venturi scrubber under various flow conditions. The Reynolds Renormalization Group (RNG k-ε turbulence model and the volume of the fluid (VOF were employed for this simulation. The effect of throat gas velocity, liquid mass flow rate, and liquid loading on pressure drop was studied. Maximum pressure drop 2064.34 pa was achieved at the throat gas velocity of 60 m/s and liquid flow rate of 0.033 kg/s and minimum pressure drop 373.51 pa was achieved at the throat gas velocity of 24 m/s and liquid flow rate of 0.016 kg/s. The results of the present study will assist for proper functioning of venturi scrubber. Keywords: Venturi scrubber, Hydrodynamics, Pressure drop, Computational fluid dynamics, Nuclear power plant safety, Flow prediction

  10. Water and chemical budgets of gravel pit lakes : Case studies of fluvial gravel pit lakes along the Meuse River (The Netherlands) and coastal gravel pit lakes along the Adriatic Sea (Ravenna, Italy)

    NARCIS (Netherlands)

    Mollema, P.N.


    Gravel pit lakes form when gravel is excavated from below the water table of a phreatic or shallow confined aquifer. Typically many of these lakes are concentrated along naturally occurring sedimentary gravel deposits in areas where gravel is needed for construction. Most gravel pit lakes are

  11. Drought and submergence tolerance in plants (United States)

    Du, Hewei; Zhou, Yufan; Oksenberg, Nir; Ronald, Pamela


    The invention provides methods of genetically modified plants to increase tolerance to drought and/or submergence. The invention additionally provides plants having increased drought and/or submergence tolerance engineered using such methods.

  12. Lessons from a Spawning Gravel Rehabilitation Program (United States)

    Pasternack, G. B.; Wheaton, J. M.; Merz, J.


    Altered sediment and flow regimes in dammed and regulated rivers limit available spawning habitat to salmonids. River managers have attempted rehabilitation of spawning habitat with gravel augmentation and riffle construction projects, but often neglect well-established conceptual models of geomorphic and ecologic processes, let alone apply them in a predictive manner. Application of such models could not only improve rehabilitation projects, but also serve to further test and evaluate the underlying scientific theories against the rigors of real-world uncertainties. For the past two years a new science-based approach to rehabilitate spawning gravels for salmonids has been under development and testing to overcome these deficiencies. The approach includes a balance of science-based quantitative tools from multiple disciplines and qualitative local knowledge relevant to the region in which it has been applied. In 2001 and 2002 it was used to design and implement the placement of 907 and 2787 metric tons of gravel, respectively, on separate reaches of the lower Mokelumne River in Central California. A long-term monitoring program to quantify outcomes and assess sustainability is on-going. Lessons from these efforts are providing for adaptive management and will be presented.

  13. Submerged membrane distillation for desalination of water

    KAUST Repository

    Francis, Lijo


    Submerged membrane modules for use for desalination of water are disclosed. In one or more aspects, the membrane modules can be submerged either in a feed solution tank or the feed solution can pass through the lumen side of the membrane submerged within the tank. The feed solution can be a water-based feed stream containing an amount of salt.

  14. Cross-flow versus counter-current flow packed-bed scrubbers: a mathematical analysis

    Energy Technology Data Exchange (ETDEWEB)

    Fthenakis, V.M.


    Little is known about the mass transfer properties of packing media exposed to a crossflow of gas and liquid, whereas there is abundant information related to counter-current scrubbers. This paper presents a theoretical analysis of mass transfer and hydrodynamics in cross- flow packed bed scrubbers and compares those with information available for counter current towers, so that the first can be evaluated and/or designed based on data derived for the second. Mathematical models of mass transfer in cross-flow and counter- current packed bed scrubbers are presented. From those, one can predict the removal effectiveness of a crossflow scrubber from the number of transfer units (NTU) calculated for a similar counterflow operation; alternatively, when the removal effectiveness in counterflow is known, one can predict the corresponding NTU in crossflow.

  15. Combustion of biomass - Energy recovery and dust separation with conventional and electrically charged scrubbers

    Energy Technology Data Exchange (ETDEWEB)

    Rawe, R.; Kuhrmann, H. (Univ. of Applied Sciences, Gelsenkirchen (Germany)), e-mail:


    In the last years a combined heat exchanger and spray scrubber for condensing operation of biomass boilers was investigated at the University of Applied Sciences in Gelsenkirchen. Flue gases are chilled more deeply as compared with conventional condensing boilers. This leads to the fact, that the rate of condensation is higher and more heat of vaporization can be recovered. Depending on temperatures and mode of operation, energy savings up to 17 % are realized. The high efficiency reduces overall emissions as less fuel is fired at the same heat output. In addition the wet separator minimizes emissions of particles, water-soluble flue gases and odours. With conventional scrubbers dust separation-efficiencies > 50 % can be achieved at high injection pressure of 3,5 bar. Looking at the different electrically charged scrubber types, either the particles and / or the scrubber fields are charged. Thus, up to 86 % efficiency is achieved using a dust-charging voltage of 25 kV. (orig.)

  16. Comparing environmental impact of air scrubbers for ammonia abatement at pig houses

    NARCIS (Netherlands)

    Vries, De Jerke W.; Melse, Roland W.


    Intensive livestock production involves environmental emissions and impacts, including emission of greenhouse gases and ammonia leading to climate change and terrestrial acidification. Ammonia emission from animal housing systems can be reduced by introducing air scrubbers for cleaning the

  17. Micro- and Nanostructural Characteristics of Particles Before and After an Exhaust Gas Recirculation System Scrubber

    DEFF Research Database (Denmark)

    Lieke, Kirsten Inga; Rosenørn, Thomas; Pedersen, Jannik


    This work provides insight into the morphology and mixing state of submicron particles in diesel exhaust from a ship engine with an exhaust gas recirculation scrubber. Particles from this low-speed ship engine on test bed were collected using a microiner-tial impactor with transmission electron...... microscopy (TEM) grids on two stages. Micro- and nanostructural characteristics of sin-gle particles were studied by TEM. Image analysis was carried out on overview and high-resolution images, revealing influence of the exhaust gas treatment (scrubber) on the particle morphology and mixing state. Soot...... agglomerates were found to be collapsed after scrubber, reflected by their change in fractal dimension (fly) from 1.88 to 2.13. Soot was predominantly found internally mixed with other components, with a higher degree of internal mix-ing observed after scrubber. Soot nanostructural characteristics on the near...

  18. Value-Added Products From FGD Sulfite-Rich Scrubber Materials

    Energy Technology Data Exchange (ETDEWEB)

    Vivak M. Malhotra


    Massive quantities of sulfite-rich flue gas desulfurization (FGD) scrubber materials are produced every year in the USA. In fact, at present, the production of wet sulfite-rich scrubber cake outstrips the production of wet sulfate-rich scrubber cake by about 6 million tons per year. However, most of the utilization focus has centered on FGD gypsum. Therefore, we have recently initiated research on developing new strategies for the economical, but environmentally-sound, utilization of sulfite-rich scrubber material. In this exploratory project (Phase I), we attempted to ascertain whether it is feasible to develop reconstituted wood replacement products from sulfite-rich scrubber material. In pursuit of this goal, we characterized two different wet sulfite-rich scrubber materials, obtained from two power plants burning Midwestern coal, for their suitability for the development of value-added products. The overall strategy adopted was to fabricate composites where the largest ingredient was scrubber material with additional crop materials as additives. Our results suggested that it may be feasible to develop composites with flexural strength as high as 40 MPa (5800 psi) without the addition of external polymers. We also attempted to develop load-bearing composites from scrubber material, natural fibers, and phenolic polymer. The polymer-to-solid ratio was limited to {le} 0.4. The formulated composites showed flexural strengths as high as 73 MPa (10,585 psi). We plan to harness the research outcomes from Phase I to develop parameters required to upscale our value-added products in Phase II.

  19. CFD analysis on gas distribution for different scrubber redirection configurations in sump cut


    Zheng, Y.; Organiscak, J.A.; Zhou, L.; Beck, T. W.; Rider, J.P.


    The National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research recently developed a series of models using computational fluid dynamics (CFD) to study the gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models using Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind t...

  20. Use of a heated graphite scrubber as a means of reducing interferences in UV-absorbance measurements of atmospheric ozone (United States)

    Turnipseed, Andrew A.; Andersen, Peter C.; Williford, Craig J.; Ennis, Christine A.; Birks, John W.


    A new solid-phase scrubber for use in conventional ozone (O3) photometers was investigated as a means of reducing interferences from other UV-absorbing species and water vapor. It was found that when heated to 100-130 °C, a tubular graphite scrubber efficiently removed up to 500 ppb ozone and ozone monitors using the heated graphite scrubber were found to be less susceptible to interferences from water vapor, mercury vapor, and aromatic volatile organic compounds (VOCs) compared to conventional metal oxide scrubbers. Ambient measurements from a graphite scrubber-equipped photometer and a co-located Federal equivalent method (FEM) ozone analyzer showed excellent agreement over 38 days of measurements and indicated no loss in the scrubber's ability to remove ozone when operated at 130 °C. The use of a heated graphite scrubber was found to reduce the interference from mercury vapor to ≤ 3 % of that obtained using a packed-bed Hopcalite scrubber. For a series of substituted aromatic compounds (ranging in volatility and absorption cross section at 253.7 nm), the graphite scrubber was observed to consistently exhibit reduced levels of interference, typically by factors of 2.5 to 20 less than with Hopcalite. Conventional solid-phase scrubbers also exhibited complex VOC adsorption and desorption characteristics that were dependent upon the relative humidity (RH), volatility of the VOC, and the available surface area of the scrubber. This complex behavior involving humidity is avoided by use of a heated graphite scrubber. These results suggest that heated graphite scrubbers could be substituted in most ozone photometers as a means of reducing interferences from other UV-absorbing species found in the atmosphere. This could be particularly important in ozone monitoring for compliance with the United States (U.S.) Clean Air Act or for use in VOC-rich environments such as in smog chambers and monitoring indoor air quality.

  1. New compact scrubber for odour removal in wastewater treatment plants. (United States)

    Sanchez, C; Couvert, A; Laplanche, A; Renner, C


    This work presents the performances of a new odour scrubber. The reactor is packed with a new structure which enables co-current operations at high gas velocities. Energy consumption and removal efficiency of sulphur compounds by oxidative alkaline scrubbing were studied. The influence of both superficial gas (U(SG)) and liquid (U(SL)) velocities, ranging from 5.6 to 28 m.s(-1) and 0.016 to 0.055 m.s(-1) respectively, were quantified. Thus, the range of 0.5 to 5 liquid-to-gas mass ratio (L/G) was studied. A comparison has been made with a previous study on static mixers (SM) and with classical random packed towers (PT). It has been shown that superficial liquid and gas velocities have a significant influence on these parameters. Hydrogen sulphide (H2S) abatement reached values up to 99%. As concerns methylmercaptan (CH3SH), the maximal removal efficiency was 87%. As a result, if well scaled-up, our reactor can be a small single stage efficient apparatus for the elimination of low concentrations of sulphur compounds as H2S and CH3SH in high flow rates of polluted gas effluents.

  2. Capillary pressure-saturation relationships for diluted bitumen and water in gravel (United States)

    Hossain, S. Zubair; Mumford, Kevin G.


    Spills of diluted bitumen (dilbit) to rivers by rail or pipeline accidents can have serious long-term impacts on environment and ecology due to the submergence and trapping of oil within the river bed sediment. The extent of this problem is dictated by the amount of immobile oil available for mass transfer into the water flowing through the sediment pores. An understanding of multiphase (oil and water) flow in the sediment, including oil trapping by hysteretic drainage and imbibition, is important for the development of spill response and risk assessment strategies. Therefore, the objective of this study was to measure capillary pressure-saturation (Pc-Sw) relationships for dilbit and water, and air and water in gravel using a custom-made pressure cell. The Pc-Sw relationships obtained using standard procedures in coarse porous media are height-averaged and often require correction. By developing and comparing air-water and dilbit-water Pc-Sw curves, it was found that correction was less important in dilbit-water systems due to the smaller difference in density between the fluids. In both systems, small displacement pressures were needed for the entry of non-wetting fluid in gravel. Approximately 14% of the pore space was occupied by trapped dilbit after imbibition, which can serve as a source of long-term contamination. While air-water data can be scaled to reasonably predict dilbit-water behaviour, it cannot be used to determine the trapped amount.

  3. Mineral resource of the month: industrial sand and gravel (United States)

    Dolley, Thomas


    With many diverse uses, industrial sand and gravel, also known as silica sand, is one of the most important nonmetallic minerals in the world. Industrial sand and gravel is a mining industry term used for sands that have a very high percentage of silicon dioxide, or greater than 95 percent quartz. Deposits of industrial sand and gravel can be found virtually everywhere on Earth, but are less widespread than deposits of common construction sand and gravel. Industrial sand and gravel is distinctive in grain size, hardness, inertness and resistance to high temperature and chemical action. Beverage containers, fiberglass insulation, fiber-optic cables and light bulbs are just some of today’s many products produced from industrial sand and gravel.

  4. Cocurrent scrubber evaluation: TVA's Colbert lime-limestone wet-scrubbing pilot plant

    Energy Technology Data Exchange (ETDEWEB)

    Hollinden, G.A.; Robards, R.F.; Moore, N.D.; Kelso, T.M.; Cole, R.M.


    The Tennessee Valley Authority (TVA) is actively engaged in a pilot plant program to develop and/or evaluate wet-scrubbing processes for removing sulfur dioxide (SO/sub 2/) from boiler flue gas. The physical size and general arrangement of flue gas scrubbing systems have a major impact on capital investment and operating cost, as do potential operating and maintenance advantages inherent to some systems. The equipment configuration for a cocurrent scrubber reflects some of these advantages. EPRI funded TVA to perform preliminary screening tests at TVA's 1 MW pilot plant (Colbert Steam Plant) to develop operating data on the cocurrent design for use in designing and operating a 10 MW prototype cocurrent scrubber at TVA's Shawnee Scrubber Test Facility. Results of Colbert tests showed excellent sulfur dioxide removal efficiencies, generally greater than 85%, low pressure drop, and high particulate removal efficiencies. This report covers these screening tests. The results indicate that commercial application of the cocurrent scrubber concept may save substantial capital investment by reducing the number of scrubber modules and auxiliary equipment. These evaluation tests provided the basis for the design and construction of the 10 MW cocurrent scrubber at the Shawnee Facility. Operation of this scrubber began in August 1978 to develop the scale-up similarities and differences between the Colbert test program (1 MW) and the Shawnee test program (10 MW). It also demonstrated the practicality and reliability of the 10 MW prototype. Detailed results of the prototype test series will be available in late 1979.

  5. EEI reports 149 stack gas scrubbers in operation in the United States

    Energy Technology Data Exchange (ETDEWEB)


    The United States operates 149 power plant stack gas scrubbers up from146 a year ago, representing 65,888 megawatts of generating capacity. Forty-two additional units are planned or under construction. Neither Canada nor Mexico has any scrubbers in operation or under construction. Stack gas scrubbers, also known as flue gas desulfurization systems, control sulfur dioxide emissions at coal-fired power plants. According to the US Environmental Protection Agency, from the peak year of 1973, up to 1987, total SO{sub 2} emissions dropped 29.4 percent. Electric power plant SO{sub 2} emissions were down 21.5 percent during the same period while utility coal use soared by 87.8 percent. In addition, the average sulfur content of coal used by utilities decreased approximately 37 percent.

  6. Pilot-scale field study for ammonia removal from lagoon biogas using an acid wet scrubber. (United States)

    Lin, Hongjian; Wu, Xiao; Miller, Curtis; Zhu, Jun; Hadlocon, Lara Jane; Manuzon, Roderick; Zhao, Lingying


    The anaerobic activities in swine slurry storage and treatment generate biogas containing gaseous ammonia component which is a chemical agent that can cause adverse environmental impacts when released to the atmosphere. The aim of this pilot plant study was to remove ammonia from biogas generated in a covered lagoon, using a sulfuric acid wet scrubber. The data showed that, on average, the biogas contained 43.7 ppm of ammonia and its concentration was found to be exponentially related to the air temperature inside the lagoon. When the air temperature rose to 35°C and the biogas ammonia concentration reached 90 ppm, the mass transfer of ammonia/ammonium from the deeper liquid body to the interface between the air and liquid became a limiting factor. The biogas velocity was critical in affecting ammonia removal efficiency of the wet scrubber. A biogas flow velocity of 8 to 12 mm s(-1) was recommended to achieve a removal efficiency of greater than 60%. Stepwise regression revealed that the biogas velocity and air temperature, not the inlet ammonia concentration in biogas, affected the ammonia removal efficiency. Overall, when 73 g L(-1) (or 0.75 M) sulfuric acid solution was used as the scrubber solution, removal efficiencies varied from 0% to 100% with an average of 55% over a 40-d measurement period. Mass balance calculation based on ammonium-nitrogen concentration in final scrubber liquid showed that about 21.3 g of ammonia was collected from a total volume of 1169 m(3) of biogas, while the scrubber solution should still maintain its ammonia absorbing ability until its concentration reaches up to 1 M. These results showed promising use of sulfuric acid wet scrubber for ammonia removal in the digester biogas.

  7. Effects of a physico-chemical treatment of a dredged sediment on its ecotoxicity after discharge in laboratory gravel pit microcosms. (United States)

    Clément, Bernard; Vaille, Gilles; Moretto, Robert; Vernus, Emmanuel; Abdelghafour, Mohammed


    In France, dredged sediments may be dumped into submerged gravel pits. As a consequence, adverse effects may be expected. In addition, groundwater quality may be impacted due to hydraulic communications with gravel pits. The immersion of dredged sediments into gravel pits should thus be restricted to clean or slightly contaminated sediments to minimize the impacts on aquatic ecosystems and human safe. For highly contaminated sediments, alternatives may be treatments aiming at removing or/and neutralizing contaminants. The Novosol treatment was aimed at neutralizing metals by complexation with orthophosphoric acid and discarding organic pollutants by calcination. The efficiency of the Novosol treatment was assessed in a scenario of sediment immersion into experimental laboratory gravel pits (LGP). A 180L water compartment was set up in each system so as to simulate the gravel pit, and various living organisms were introduced. Following a period of colonization and stabilization, raw and treated sediments were introduced into two different LGPs, and the fate and effects of pollutants were studied during the period of deposition and post-deposition. The treatment had positive effects on survival and development of benthic populations and reproduction of pond snails but the introduction of the treated sediment was followed by an increase in salinity (phosphates, sulphates) and a peak of hexavalent chromium at concentrations above drinkability limits and likely to have impaired invertebrate populations of the water column. The results of this study suggest that discharge of contaminated sediments at a high solid:liquid ratio (1:10) in gravel pits or equivalent aquatic ecosystems may have only limited effects on biota and ground water quality. The Novosol treatment should, however, be improved so as to increase efficiency of oxidised chromium complexation during the phosphatation step. (c) 2009 Elsevier B.V. All rights reserved.

  8. Performance of a Venturi scrubber in the removal of fine powder from a confined gas stream

    Directory of Open Access Journals (Sweden)

    Maria Angélica Martins Costa


    Full Text Available Experimental results on the performance of a laboratory scale rectangular Venturi scrubber in the removal of fine mineral particles from a confined air stream are presented, and a new correlation is proposed and evaluated. The scrubber was operated with air velocities in the throat varying from 58 m/s to 75 m/s and liquid flow rates varying from 280 ml/min to 900 ml/min. Liquid was injected as a jet emerging from a 1.0 mm orifice at the throat. Results for dust collection grade efficiency varied from 87% to 98% for particles from 0.1 µm to 2.0 µm.

  9. Examination of a newly developed mobile dry scrubber (DS) for coal mine dust control applications (United States)

    Organiscak, J.; Noll, J.; Yantek, D.; Kendall, B.


    The Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) conducted laboratory testing of a self-tramming, remotely controlled mobile Dry Scrubber (DS) that J.H. Fletcher and Co. developed under a contract with NIOSH OMSHR to reduce the exposure of miners to airborne dust. The scrubber was found to average greater than 95 percent dust removal efficiency with disposable filters, and 88 and 90 percent, respectively, with optional washable filters in their prewash and post-wash test conditions. Although the washable filters can be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-min washing period. The scrubber’s velocity-pressure-regulated variable-frequency-drive fan maintained relatively consistent airflow near the targeted 1.42 and 4.25 m3/s (3,000 and 9,000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60-Hz fan motor frequency or horsepower rating at 2,610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8,420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the scrubber showed that the outlet side of the scrubber was noisier, and the loaded filters increased sound levels compared with clean filters at the same airflow quantities. With loaded filters, the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6,000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level — under Title 30 Code of Federal Regulations Part 62.101— of 90 dB(A) at or below this airflow quantity. The scrubber’s washable filters were not used during field-testing because of their lower respirable dust removal efficiency and the airborne dust generated by filter washing. Field-testing the scrubber with disposable filters at two underground coal mine sections showed that

  10. Gas Absorption by Alkaline Solution in a Cyclone Scrubber: Experimental and Modeling Study

    Directory of Open Access Journals (Sweden)

    Mariana Mariana


    Full Text Available Experimental and modeling studies have been conducted on a CO2 absorption in a cyclone scrubber operated at room temperature. The effects of parameters such as the initial concentration of alkali in the solution and the liquid – gas ratio on the CO2 absorbed flux were experimentally and theoretically investigated. A theoretical study has been performed using a mathematical model based on the absorption in the liquid droplet with instantaneous reaction, in the inlet duct of the cyclone and in the cyclone itself. The results from the model were compared with experimental data and showed satisfactory agreement.   Keywords: CO2 removal, mathematical model, wet cyclone scrubber

  11. Size reduction of ammonia scrubbers for pig and poultry houses: Use of conditional bypass vent at high air loading rates

    NARCIS (Netherlands)

    Melse, R.W.; Wagenberg, van A.V.; Mosquera, J.


    In The Netherlands, both acid and biological air scrubbers are used for removal of ammonia from exhaust air at pig and poultry houses. Current regulations require that scrubbers are dimensioned for treating the maximum airflow rate that may occur, so on average these systems are overdimensioned and

  12. Removal of particulate matter (PM10) by air scrubbers at livestock facilities: results of an on-farm monitoring program.

    NARCIS (Netherlands)

    Melse, R.W.; Hofschreuder, P.; Ogink, N.W.M.


    Air scrubbers are commonly used for removal of ammonia and odor from exhaust air of animal houses in the Netherlands. In addition, air scrubbers remove a part of the particulate matter. In this article, the results of an on-farm monitoring are presented in which PM10 removal was monitored at 24

  13. Flow and scour around vertical submerged structures

    Indian Academy of Sciences (India)

    Although past investigations establish the effect of various parameters on scour around vertical submerged structures for live and clear water condition, yet further studies are required to analyze the scour around group of submerged structures for various bed sediments, understand the flow physics around the group and ...

  14. Multi-Pollutant and One-Stage Scrubbers for Removal of Ammonia, Odor, and Particulate Matter from Animal House Exhaust Air

    NARCIS (Netherlands)

    Ogink, N.W.M.; Melse, R.W.; Mosquera Losada, J.


    In several European countries, acid scrubbers and bio-scrubbers are off-the-shelf techniques for effective removal of ammonia from exhaust air from animal houses and, to a lesser extent, for odor. The number of operating air scrubbers at livestock operations in the Netherlands in 2008 is estimated

  15. Subsurface flow in lowland river gravel bars (United States)

    Bray, E. N.; Dunne, T.


    Geomorphic and hydraulic processes, which form gravel bars in large lowland rivers, have distinctive characteristics that control the magnitude and spatial patterns of infiltration and exfiltration between rivers and their immediate subsurface environments. We present a bedform-infiltration relation together with a set of field measurements along two reaches of the San Joaquin River, CA to illustrate the conditions required for infiltration and exfiltration of flow between a stream and its undulating bed, and a numerical model to investigate the factors that affect paths and residence times of flow through barforms at different discharges. It is shown that asymmetry of bar morphology is a first-order control on the extent and location of infiltration, which would otherwise produce equal areas of infiltration and exfiltration under the assumption of sinusoidal bedforms. Hydraulic conductivity varies by orders of magnitude due to fine sediment accumulation and downstream coarsening related to the process of bar evolution. This systematic variability not only controls the magnitude of infiltration, but also the residence time of flow through the bed. The lowest hydraulic conductivity along the reach occurred where the difference between the topographic gradient and the water-surface gradient is at a maximum and thus where infiltration would be greatest into a homogeneous bar, indicating the importance of managing sand supply to maintain the ventilation and flow through salmon spawning riffles. Numerical simulations corroborate our interpretation that infiltration patterns and rates are controlled by distinctive features of bar morphology.

  16. Dust captures effectiveness of scrubber systems on mechanical miners operating in larger roadways.

    CSIR Research Space (South Africa)

    Hole, BJ


    Full Text Available The project was directed towards bord and pillar working by mechanised miners operating in larger section roadways, where the problem of scrubber capture tends to be greatest owing to the limited size of the zone of influence around exhaust...

  17. Removal of nitrogen by Algal Turf Scrubber Technology in recirculating aquaculture system

    NARCIS (Netherlands)

    Valeta, J.; Verdegem, M.C.J.


    Ongoing research in recirculation aquaculture focuses on evaluating and improving the purification potential of different types of filters. Algal Turf Scrubber (ATS) are special as they combine sedimentation and biofiltration. An ATS was subjected to high nutrient loads of catfish effluent to

  18. Use of a heated graphite scrubber as a means of reducing interferences in UV-absorbance measurements of atmospheric ozone

    Directory of Open Access Journals (Sweden)

    A. A. Turnipseed


    Full Text Available A new solid-phase scrubber for use in conventional ozone (O3 photometers was investigated as a means of reducing interferences from other UV-absorbing species and water vapor. It was found that when heated to 100–130 °C, a tubular graphite scrubber efficiently removed up to 500 ppb ozone and ozone monitors using the heated graphite scrubber were found to be less susceptible to interferences from water vapor, mercury vapor, and aromatic volatile organic compounds (VOCs compared to conventional metal oxide scrubbers. Ambient measurements from a graphite scrubber-equipped photometer and a co-located Federal equivalent method (FEM ozone analyzer showed excellent agreement over 38 days of measurements and indicated no loss in the scrubber's ability to remove ozone when operated at 130 °C. The use of a heated graphite scrubber was found to reduce the interference from mercury vapor to ≤ 3 % of that obtained using a packed-bed Hopcalite scrubber. For a series of substituted aromatic compounds (ranging in volatility and absorption cross section at 253.7 nm, the graphite scrubber was observed to consistently exhibit reduced levels of interference, typically by factors of 2.5 to 20 less than with Hopcalite. Conventional solid-phase scrubbers also exhibited complex VOC adsorption and desorption characteristics that were dependent upon the relative humidity (RH, volatility of the VOC, and the available surface area of the scrubber. This complex behavior involving humidity is avoided by use of a heated graphite scrubber. These results suggest that heated graphite scrubbers could be substituted in most ozone photometers as a means of reducing interferences from other UV-absorbing species found in the atmosphere. This could be particularly important in ozone monitoring for compliance with the United States (U.S. Clean Air Act or for use in VOC-rich environments such as in smog chambers and monitoring indoor air quality.

  19. Shipping and the environment: Smokestack emissions, scrubbers and unregulated oceanic consequences

    Directory of Open Access Journals (Sweden)

    David R. Turner


    Full Text Available While shipping has long been recognised as a very carbon-efficient transport medium, there is an increasing focus on its broader environmental consequences. The International Maritime Organisation is responsible for the regulation of ship emissions arising from fuel combustion. Their current regulations are, however, much less strict than those applying to land-based transport within the European Union. Five different groups of pollutant emission from ship smokestacks are addressed in this paper: sulphur oxides, nitrogen oxides, particulate matter, organic matter and metals. The reduction of sulphur oxide emissions into the atmosphere using scrubber technology adds another dimension to the discussion, as this approach results in focused discharge of some pollutants to the surface water. A scoping calculation shows that an open-loop scrubber on a medium-sized ship could discharge more copper and zinc daily to the surface water than the ship’s antifouling paint. The use of antifouling paint in the European Union is subject to a prior risk assessment, but scrubber discharges are not subject to any such risk assessment. This situation presents a problem from the perspective of the Marine Strategy Framework Directive, as environmental monitoring programmes in some coastal areas of the Baltic Sea have shown that levels of both copper and zinc exceed environmental quality standards. To fulfil the Marine Strategy Framework Directive requirements and achieve Good Environmental Status, having knowledge of the magnitude of different anthropogenic pressures is important. Metal inputs from open-loop scrubbers have been largely neglected until now: some metals have the potential to serve as tracers for monitoring scrubber discharges.

  20. Experimental investigation on heat transport in gravel-sand materials

    DEFF Research Database (Denmark)

    Maureschat, Gerald; Heller, Alfred


    The project is a basic study on the expected thermal behaviour of gravel storage initiated as a part of a research and demonstration gravel storage for seasonal heat storage.The goal of the investigation is to determine the heat transfer between heat pipes and sand-gravel storage media by carrying...... out in a small size experiment. The experiment consists of a highly insulated box filled with two kinds of sand material crossed by a plastic heat pipe. Heat transfer is measured under dry and water satured conditions in a cross-section.The conclusions are clear. To obtain necessary heat conduction...... in sand-gravel material, the storage media is to be water satured. In this case, handling of such material on site is rather complex. The conduction is highly dependent on the thermal properties of the storage media and so is the overall thermal performance of a storage applying such media. For sandy...

  1. Effects of scrubber by-product-stabilized dairy lagoon sludge on growth and physiological responses of sunflower (Helianthus annuus L.). (United States)

    Thomas, Carla N; Bauerle, William L; Chastain, John P; Owino, Tom O; Moore, Kathy P; Klaine, Stephen J


    Brick manufacturing industries are challenged to comply with clean air mandates. Dry air scrubbers have been used to remove acid gases from the exhaust air from brick manufacturing plants. The use of dry air scrubbers results in the production of large quantities of an alkaline powder by-product. A greenhouse experiment was conducted to evaluate the potential of using dairy lagoon sludge stabilized with the scrubber by-product as a soil amendment. Lagoon sludge was stabilized with scrubber by-product at an application rate of 20 gl(-1). The sludge-scrubber by-product mixture was applied to a sandy loam soil to provide amendments ranging between 28 and 168 kg of plant available nitrogen (PAN)/ha for the growth of Helianthus annuus (sunflower). Use of the sludge-scrubber by-product mixture as a nitrogen fertilizer did not adversely affect sunflower seedling emergence; however, significantly higher (psunflower tissues was generally within a sufficient range. The increased growth and yield of sunflower plants indicated the potential of the sludge-scrubber by-product mixture as a soil amendment in agricultural crop production.

  2. Laboratory measurements of gravel thermal properties. A methodology proposal (United States)

    Cultrera, Matteo; Peron, Fabio; Bison, Paolo; Dalla Santa, Giorgia; Bertermann, David; Muller, Johannes; Bernardi, Adriana; Galgaro, Antonio


    Gravel thermal properties measurements at laboratory level is quite challenging due to several technical and logistic issues, mainly connected to the sediment sizes and the variability of their mineralogical composition. The direct measurement of gravel thermal properties usually are not able to involve a representative volume of geological material, consequently the thermal measurements performed produce much dispersed results and not consistent due to the large interstitial voids and the poor physical contact with the measuring sensors. With the aim of directly provide the measurement of the gravel thermal properties, a new methodology has been developed and some results are already available on several gravel deposits samples around Europe. Indeed, a single guarded hot plate Taurus Instruments TLP 800 measured the gravel thermal properties. Some instrumental adjustments were necessary to adapt the measuring devices and to finalize the thermal measurements on gravels at the IUAV FISTEC laboratory (Environmental Technical Physics Laboratory of Venice University). This device usually provides thermal measurements according to ISO 8302, ASTM C177, EN 1946-2, EN 12664, EN 12667 and EN 12939 for building materials. A preliminary calibration has been performed comparing the outcomes obtained with the single guarded hot plate with a needle probe of a portable thermal conductivity meter (ISOMET). Standard sand (ISO 67:2009) is used as reference material. This study is provided under the Cheap-GSHPs project that has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement no. 657982

  3. Washing technology development for gravel contaminated with uranium

    Energy Technology Data Exchange (ETDEWEB)

    Park, Uk Ryang; Kim, Gye Nam; Kim, Seung Soo; Kim, Wan Suk; Moon, Jai Kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    The soil washing method has a short decontamination time and is economical. In addition, methods including phytoremediation, solidification/stabilization and bioremediation exist. Phytoremediation and bioremediation are economical, but have low remedial efficiency. In addition, bioremediation causes washing wastewater because it requires a washing process for the separation of microorganisms from the soils. In addition, solidification/stabilization is a commonly used methods, but eventually increases the volume of wastes. As mentioned above, many researches involved in the decontamination of radioactively contaminated soils have been actively processed. On the other hand, researches for decontaminating radioactively contaminated gravels are not being currently processed. In this study, we performed basic experiments using decontamination methods to decontaminate radioactively contaminated gravel. First, we measured the concentration of uranium in gravel included in uranium-contaminated soils and performed a washing experiment to monitor the tendency of uranium removal. In addition, when managing gravel with a low uranium-decontamination rate, we tried to satisfy the radioactivity concentration criteria for self-disposal in the wastes (0.4Bq/g or less) by performing a washing experiment after only a physical crushing process. We performed washing experiments to satisfy the radioactivity concentration criteria for self-disposal (0.4 Bq/g or less) in gravel included in radioactively contaminated soil. We performed washing experiments for gravel whose initial average concentration of uranium was 1.3Bq/g. In addition, the average concentration of uranium was 0.8Bq/g. Too increase the decontamination rate, we crushed the gravel with a jaw crusher and performed the washing experiments. The results were similar to the results without crushing. In addition, it was determined that the smaller the size of the gravel particles, the more efficient the uranium decontamination

  4. Performance of high-rate gravel-packed oil wells

    Energy Technology Data Exchange (ETDEWEB)

    Unneland, Trond


    Improved methods for the prediction, evaluation, and monitoring of performance in high-rate cased-hole gravel-packed oil wells are presented in this thesis. The ability to predict well performance prior to the gravel-pack operations, evaluate the results after the operation, and monitor well performance over time has been improved. This lifetime approach to performance analysis of gravel-packed oil wells contributes to increase oil production and field profitability. First, analytical models available for prediction of performance in gravel-packed oil wells are reviewed, with particular emphasis on high-velocity flow effects. From the analysis of field data from three North Sea oil fields, improved and calibrated cased-hole gravel-pack performance prediction models are presented. The recommended model is based on serial flow through formation sand and gravel in the perforation tunnels. In addition, new correlations for high-velocity flow in high-rate gravel-packed oil wells are introduced. Combined, this improves the performance prediction for gravel-packed oil wells, and specific areas can be targeted for optimized well design. Next, limitations in the current methods and alternative methods for evaluation and comparison of well performance are presented. The most widely used parameter, the skin factor, remains a convenient and important parameter. However, using the skin concept in direct comparisons between wells with different reservoir properties may result in misleading or even invalid conclusions. A discussion of the parameters affecting the skin value, with a clarification of limitations, is included. A methodology for evaluation and comparison of gravel-packed well performance is presented, and this includes the use of results from production logs and the use of effective perforation tunnel permeability as a parameter. This contributes to optimized operational procedures from well to well and from field to field. Finally, the data sources available for

  5. Inactivation of airborne Enterococcus faecalis and infectious bursal disease virus using a pilot-scale ultraviolet photocatalytic oxidation scrubber

    NARCIS (Netherlands)

    Zhao, Y.; Aarnink, A.J.A.; Xin, H.


    High microbial concentrations and emissions associated with livestock houses raise health and environmental concerns. A pilot-scale ultraviolet photocatalytic (UV-PCO) scrubber was tested for its efficacy to inactivate aerosolized Enterococcus faecalis and infectious bursal disease virus (IBDV).

  6. Modelling air pollution abatement in deep street canyons by means of air scrubbers

    CERN Document Server

    De Giovanni, Marina; Avveduto, Alessandro; Pace, Lorenzo; Salisburgo, Cesare Dari; Giammaria, Franco; Monaco, Alessio; Spanto, Giuseppe; Tripodi, Paolo


    Deep street canyons are characterized by weak ventilation and recirculation of air. In such environment, the exposure to particulate matter and other air pollutants is enhanced, with a consequent worsening of both safety and health. The main solution adopted by the international community is aimed at the reduction of the emissions. In this theoretical study, we test a new solution: the removal of air pollutants close to their sources by a network of Air Pollution Abatement (APA) devices. The APA technology depletes gaseous and particulate air pollutants by a portable and low-consuming scrubbing system, that mimics the processes of wet and dry deposition. We estimate the potential pollutant abatement efficacy of a single absorber by Computational Fluid Dynamics (CFD) method. The presence of the scrubber effectively creates an additional sink at the bottom of the canyon, accelerating its cleaning process by up to 70%, when an almost perfect scrubber (90% efficiency) is simulated. The efficacy of absorber is not...

  7. Numerical Simulations of Airflow and Droplet Dispersion in a Horizontal Ammonia Scrubber

    DEFF Research Database (Denmark)

    Liu, Li; Nielsen, Peter Vilhelm; Heiselberg, Per Kvols


    from a piggery. In this study, numerical method were used to investigate airflow pattern, droplet dispersion, ammonia absorption at droplet surface and overall removal efficiency in an air cleaner. Droplet trajectories and elapsed time in air were adopted to characterize the absorption efficiency......Ammonia released in pig production industries can lead to eutrophication of surface waters, soil acidification, fertilization of vegetation and changes in ecosystems, etc. Air scrubbers with spray of aerosolized sulphur solution were used to remove the ammonia mixed in the airflow ventilated out......, and they were simulated by Eularian-Lagrangian method of Computation Fluid Dynamics (CFD). Realizable k-ε turbulence model were used to simulate airflow turbulence. Strong vortex rotating around the main stream direction were found along the scrubber. To weaken the vortex, the impact of adding a regulating...

  8. Design of artificial neural networks using a genetic algorithm to predict collection efficiency in venturi scrubbers. (United States)

    Taheri, Mahboobeh; Mohebbi, Ali


    In this study, a new approach for the auto-design of neural networks, based on a genetic algorithm (GA), has been used to predict collection efficiency in venturi scrubbers. The experimental input data, including particle diameter, throat gas velocity, liquid to gas flow rate ratio, throat hydraulic diameter, pressure drop across the venturi scrubber and collection efficiency as an output, have been used to create a GA-artificial neural network (ANN) model. The testing results from the model are in good agreement with the experimental data. Comparison of the results of the GA optimized ANN model with the results from the trial-and-error calibrated ANN model indicates that the GA-ANN model is more efficient. Finally, the effects of operating parameters such as liquid to gas flow rate ratio, throat gas velocity, and particle diameter on collection efficiency were determined.

  9. Gas pollutants removal in a single- and two-stage ejector-venturi scrubber. (United States)

    Gamisans, Xavier; Sarrà, Montserrrat; Lafuente, F Javier


    The absorption of SO(2) and NH(3) from the flue gas into NaOH and H(2)SO(4) solutions, respectively has been studied using an industrial scale ejector-venturi scrubber. A statistical methodology is presented to characterise the performance of the scrubber by varying several factors such as gas pollutant concentration, air flowrate and absorbing solution flowrate. Some types of venturi tube constructions were assessed, including the use of a two-stage venturi tube. The results showed a strong influence of the liquid scrubbing flowrate on pollutant removal efficiency. The initial pollutant concentration and the gas flowrate had a slight influence. The use of a two-stage venturi tube considerably improved the absorption efficiency, although it increased energy consumption. The results of this study will be applicable to the optimal design of venturi-based absorbers for gaseous pollution control or chemical reactors.

  10. Turbidity removal: Gravel and charcoal as roughing filtration media

    Directory of Open Access Journals (Sweden)

    Josiah A. Adeyemo


    Full Text Available Roughing filtration is an important pre-treatment process for wastewater, because it efficiently separates fine solid particles over prolonged periods, without the addition of chemicals. For this study, a pilot plant was designed at Delmas Coal Mine in the Mpumalanga province of South Africa. The design and sizing of the pilot plant was guided by Wegelin’s design criteria. Gravel was used as a control medium because it is one of the most commonly used roughing filter media and because it was used in developing the criteria. We compared the performance of gravel as a filter medium to that of another locally available material, charcoal, for the removal of turbidity in wastewater. The pilot plant was monitored continuously for 90 days from commissioning until the end of the project. The overall performance of the roughing filter in turbidity removal, using gravel or charcoal, was considered efficient for the pre-treatment of waste water. Charcoal performed slightly better than gravel as a filter medium for the removal of turbidity, possibly because charcoal has a slightly higher specific surface area and porosity than gravel, which could enhance sedimentation and other filtration processes, such as adsorption, respectively.

  11. Impeller Submergence Depth for Stirred Tanks

    Directory of Open Access Journals (Sweden)

    Thiyam T. Devi


    Full Text Available Impeller submergence governs the performance of mixing tanks employed in oxygen transfer operation. Present work experimentally investigates the effect of impeller submergence depths on oxygen transfer and corresponding power consumption. It has been found that at higher range of impeller submergence, mixing tanks consume less power and gives higher values of oxygen transfer coefficient. Optimal range of submergence depth is 0.7 to 0.9 times the impeller diameter. Copyright ©2011 BCREC UNDIP. All rights reserved.(Received: 4th March 2011; Revised: 12nd July 2011; Accepted: 14th July 2011[How to Cite: T.T. Devi, A.P. Sinha, M. Thakre, and B. Kumar. (2011. Impeller Submergence Depth for Stirred Tanks. Bulletin of Chemical Reaction Engineering & Catalysis, 6 (2: 123-128. doi:10.9767/bcrec.6.2.826.123-128][How to Link / DOI: || or local:] | View in 

  12. Incorporation of alpha-Ketoglutaric Acid as a Fixed Bed Scrubber Media for the Neutralization of Hydrazine Family Hypergolic Fuels (United States)

    DeVor, R. W.; Santiago-Maldonado, E.; Parkerson, J. K.


    A candidate scrubber media, alpha-ketoglutaric acid (aKGA) adsorbed onto a silica-based substrate was examined as a potential alternative to the hydrazine-family hypergolic fuel neutralization techniques currently utilized at NASA/Kennedy Space Center (KSC). Helvenson et. al. has indicated that aKGA will react with hydrazines to produce non-hazardous, possibly biodegradable products. Furthermore, the authors have previously tested and demonstrated the use of aKGA aqueous solutions as a replacement neutralizing agent for citric acid, which is currently used as a scrubbing agent in liquid scrubbers at KSC. Specific properties examined include reaction efficiency, the loading capacity of aKGA onto various silica substrates, and the comparison of aKGA media performance to that of the citric acid vapor scrubber systems at KSC and a commercial vapor scrubber media. Preliminary investigations showed hydrophobic aerogel particles to be an ideal substrate for the deposition of the aKGA. Current studies have shown that the laboratory produced aKGA-Aerogel absorbent media are more efficient and cost effective than a commercially available fixed bed scrubber media, although much less cost effective than liquid-based citric acid scrubbers (although possibly safer and less labor intensive). A comparison of all three alternative scrubber technologies (liquid aKGA, solid-phase aKGA, and commercially available sorbent materials) is given considering both hypergolic neutralization capabilities and relative costs (as compared to the current citric acid scrubbing technology in use at NASA/KSC).

  13. Laser Beam Submerged Arc Hybrid Welding (United States)

    Reisgen, Uwe; Olschok, Simon; Jakobs, Stefan; Schleser, Markus; Mokrov, Oleg; Rossiter, Eduardo

    The laser beam-submerged arc hybrid welding method originates from the knowledge that, with increasing penetration depth, the laser beam process has a tendency to pore formation in the lower weld regions. The coupling with the energy-efficient submerged-arc process improves degassing and reduces the tendency to pore formation. The high deposition rate of the SA process in combination with the laser beam process offers, providing the appropriate choice of weld preparation, the possibility of welding plates with a thickness larger than 20° mm in a single pass, and also of welding thicker plates with the double-sided single pass technique.

  14. Evaluation of gravel concentration and soil strength in upland rice ...

    African Journals Online (AJOL)

    Evaluation of gravel concentration and soil strength in upland rice cultivation in Abeokuta, Southwestern Nigeria. FK Salako, O Osiname. Abstract. No Abstract. Nigerian Journal of Soil Sciences Vol. 16 (1) 2006: pp. 67-76. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

  15. Performance comparison of plant root biofilm, gravel attached ...

    African Journals Online (AJOL)

    Performance comparison of plant root biofilm, gravel attached biofilm and planktonic microbial populations, in phenol removal within a constructed wetland wastewater treatment system. Eyal Kurzbaum1*, Felix Kirzhner2 and Robert Armon2. 1Golan Research Institute, University of Haifa, P.O. Box 97, Katzrin 12900, Israel.

  16. Development and evaluation of a full-scale spray scrubber for ammonia recovery and production of nitrogen fertilizer at poultry facilities. (United States)

    Hadlocon, Lara Jane S; Manuzon, Roderick B; Zhao, Lingying


    Significant ammonia emissions from animal facilities need to be controlled due to its negative impacts on human health and the environment. The use of acid spray scrubber is promising, as it simultaneously mitigates and recovers ammonia emission for fertilizer. Its low pressure drop contribution on axial fans makes it applicable on US farms. This study develops a full-scale acid spray scrubber to recover ammonia emissions from commercial poultry facilities and produce nitrogen fertilizer. The scrubber performance and economic feasibility were evaluated at a commercial poultry manure composting facility that released ammonia from exhaust fans with concentrations of 66-278 ppmv and total emission rate of 96,143 kg yr(-1). The scrubber consisted of 15 spray scrubber modules, each equipped with three full-cone nozzles that used dilute sulphuric acid as the medium. Each nozzle was operated at 0.59 MPa with a droplet size of 113 μm and liquid flow rate of 1.8 L min(-1). The scrubber was installed with a 1.3-m exhaust fan and field tested in four seasons. Results showed that the scrubber achieved high NH3 removal efficiencies (71-81%) and low pressure drop (scrubber effluents containing 22-36% (m/v) ammonium sulphate are comparable to the commercial-grade nitrogen fertilizer. Preliminary economic analysis indicated that the break-even time is one year. This study demonstrates that acid spray scrubbers can economically and effectively recover NH3 from animal facilities for fertilizer.

  17. Multielement stoichiometry of submerged macrophytes across Yunnan plateau lakes (China)

    National Research Council Canada - National Science Library

    Xing, Wei; Wu, Haoping; Shi, Qiao; Hao, Beibei; Liu, Han; Wang, Zhixiu; Liu, Guihua


    .... We predicted that tissue element composition in submerged macrophytes is affected by lake trophic level and taxonomy, and submerged macrophytes have weak stoichiometric homeostasis for all above 16 elements...

  18. Sediment supply controls equilibrium channel geometry in gravel rivers. (United States)

    Pfeiffer, Allison M; Finnegan, Noah J; Willenbring, Jane K


    In many gravel-bedded rivers, floods that fill the channel banks create just enough shear stress to move the median-sized gravel particles on the bed surface (D50). Because this observation is common and is supported by theory, the coincidence of bankfull flow and the incipient motion of D50 has become a commonly used assumption. However, not all natural gravel channels actually conform to this simple relationship; some channels maintain bankfull stresses far in excess of the critical stress required to initiate sediment transport. We use a database of >300 gravel-bedded rivers and >600 10Be-derived erosion rates from across North America to explore the hypothesis that sediment supply drives the magnitude of bankfull shear stress relative to the critical stress required to mobilize the median bed surface grain size ([Formula: see text]). We find that [Formula: see text] is significantly higher in West Coast river reaches (2.35, n = 96) than in river reaches elsewhere on the continent (1.03, n = 245). This pattern parallels patterns in erosion rates (and hence sediment supplies). Supporting our hypothesis, we find a significant correlation between upstream erosion rate and local [Formula: see text] at sites where this comparison is possible. Our analysis reveals a decrease in bed surface armoring with increasing [Formula: see text], suggesting channels accommodate changes in sediment supply through adjustments in bed surface grain size, as also shown through numerical modeling. Our findings demonstrate that sediment supply is encoded in the bankfull hydraulic geometry of gravel bedded channels through its control on bed surface grain size.

  19. Advance, Retreat, and Halt of Abrupt Gravel-Sand Transitions in Alluvial Rivers (United States)

    Blom, Astrid; Chavarrías, Víctor; Ferguson, Robert I.; Viparelli, Enrica


    Downstream fining of bed sediment in alluvial rivers is usually gradual, but often an abrupt decrease in characteristic grain size occurs from about 10 to 1 mm, i.e., a gravel-sand transition (GST) or gravel front. Here we present an analytical model of GST migration that explicitly accounts for gravel and sand transport and deposition in the gravel reach, sea level change, subsidence, and delta progradation. The model shows that even a limited gravel supply to a sand bed reach induces progradation of a gravel wedge and predicts the circumstances required for the gravel front to advance, retreat, and halt. Predicted modern GST migration rates agree well with measured data at Allt Dubhaig and the Fraser River, and the model qualitatively captures the behavior of other documented gravel fronts. The analysis shows that sea level change, subsidence, and delta progradation have a significant impact on the GST position in lowland rivers.

  20. Fisher Sand & Gravel New Mexico, Inc. General Air Quality Permit: Related Documents (United States)

    Documents related to the Fisher Sand & Gravel – New Mexico, Inc., Grey Mesa Gravel Pit General Air Quality Permit for New or Modified Minor Source Stone Quarrying, Crushing, and Screening Facilities in Indian Country.

  1. Oxygen dynamics in submerged rice (Oryza sativa L.)

    DEFF Research Database (Denmark)

    Colmer, Timothy D.; Pedersen, Ole


    Complete submergence of plants prevents direct O2 and CO2 exchange with air. Underwater photosynthesis can result in marked diurnal changes in O2 supply to submerged plants. Dynamics in pO2 had not been measured directly for submerged rice (Oryza sativa), but in an earlier study, radial O2 loss...

  2. Improving sand and gravel utilization and land-use planning. - 3D-modelling gravel resources with geospatial data. (United States)

    Rolstad Libach, Lars; Wolden, Knut; Dagestad, Atle; Eskil Larsen, Bjørn


    The Norwegian aggregate industry produces approximately 14 million tons of sand and gravel aggregates annually to a value of approximately 100 million Euros. Utilization of aggregates are often linked to land-use conflicts and complex environmental impacts at the extraction site. These topics are managed on a local municipal level in Norway. The Geological Survey of Norway has a database and a web map service with information about sand and gravel deposits with considerable volumes and an importance evaluation. Some of the deposits covers large areas where the land-use conflicts are high. To ease and improve land-use planning, safeguard other important resources like groundwater and sustainable utilization of sand and gravel resources - there is a need for more detailed information of already mapped important resources. Detailed 3D-models of gravel deposits is a tool for a better land-use- and resource management. By combining seismic, GPR and resistivity geophysical profile data, borehole data, quaternary maps and lidar surface data, it has been possible to make 3D-models of deposits and to further research the possibilities for distinguishing different qualities and volumes. Good datasets and a detailed resource map is a prerequisite to assess geological resources for planners, extractors and neighbours. Future challenges lies in use of, often old, geophysical data, and combining these. What kind of information is it possible to grasp from depth-data that actually argues for a more detailed delineation of resources?

  3. Benthic bacterial diversity in submerged sinkhole ecosystems. (United States)

    Nold, Stephen C; Pangborn, Joseph B; Zajack, Heidi A; Kendall, Scott T; Rediske, Richard R; Biddanda, Bopaiah A


    Physicochemical characterization, automated ribosomal intergenic spacer analysis (ARISA) community profiling, and 16S rRNA gene sequencing approaches were used to study bacterial communities inhabiting submerged Lake Huron sinkholes inundated with hypoxic, sulfate-rich groundwater. Photosynthetic cyanobacterial mats on the sediment surface were dominated by Phormidium autumnale, while deeper, organically rich sediments contained diverse and active bacterial communities.

  4. Production of extracellular aspartic protease in submerged ...

    African Journals Online (AJOL)


    29(1): 1-6. Fraile ER, Bernardinelli SE, Handel M, Jauregui AM (1978). Selección de cepas de Mucor sp productoras de enzimas coagulantes de leche. Rev. Arg. Microbiol. 10(2): 65-69. Ghareib M, Hamdy HS, Khalil AA (2001). Production of intracellular milk clotting enzyme in submerged cultures of Fusarium subglutinans.

  5. Topology optimization for submerged buoyant structures

    NARCIS (Netherlands)

    Picelli, R.; van Dijk, R.; Vicente, W.M.; Pavanello, R.; Langelaar, M.; van Keulen, A.


    This paper presents an evolutionary structural topology optimization method for the design of completely submerged buoyant modules with design-dependent fluid pressure loading. This type of structure is used to support offshore rig installation and pipeline transportation at all water depths. The

  6. Production of extracellular aspartic protease in submerged ...

    African Journals Online (AJOL)

    Fungal milk-clotting enzymes have gained value as bovine Chymosin substitutes in the cheese industry. In this work, the effects of culture conditions on the production of extracellular milk clotting enzymes from Mucor mucedo DSM 809 in submerged fermentation were studied. The maximum activity was observed after 48 h ...

  7. Ecological effects of re-introduction of salmonid spawning gravel in lowland Danish streams

    DEFF Research Database (Denmark)

    Pedersen, Morten Lauge; Kristensen, Esben; Kronvang, Brian


    recently been conducted in many streams and rivers. However, systematic monitoring of these spawning gravel restoration projects is limited. The overall aim of this paper was to evaluate gravel reintroduction as a long-term salmonid rehabilitation method in 32 lowland streams. Displacement of gravel...

  8. Prediction of sand transport over immobile gravel from supply limited to capacity conditions (United States)

    The prediction of the transport of sand in armored gravel reaches downstream of dams is complicated by variable bed conditions ranging from sand transported through gravel to sand in transport over buried gravel. Knowledge of the rate of sand transport in these conditions, however, is necessary for...

  9. 32 CFR 644.505 - Disposal plan for embedded gravel, sand or stone. (United States)


    ... 32 National Defense 4 2010-07-01 2010-07-01 true Disposal plan for embedded gravel, sand or stone. 644.505 Section 644.505 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY... Gravel, Sand and Stone § 644.505 Disposal plan for embedded gravel, sand or stone. Prior to offering sand...

  10. 40 CFR 436.30 - Applicability; description of the construction sand and gravel subcategory. (United States)


    ... construction sand and gravel subcategory. 436.30 Section 436.30 Protection of Environment ENVIRONMENTAL... CATEGORY Construction Sand and Gravel Subcategory § 436.30 Applicability; description of the construction sand and gravel subcategory. The provisions of this subpart are applicable to the mining and the...

  11. Cocurrent scrubber evaluation TVA's Colbert Lime--Limestone Wet-Scrubbing Pilot Plant. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Robards, R.F.; Moore, N.D.; Kelso, T.M.; Cole, R.M.


    The Tennessee Valley Authority (TVA) is actively engaged in a pilot plant program to develop and/or evaluate wet-scrubbing processes for removing sulfur dioxide (SO/sub 2/) from boiler flue gas. The physical size and general arrangement of flue gas scrubbing systems have a major impact on capital investment and operating cost, as do potential operating and maintenance advantages inherent to some systems. The equipment configuration for a cocurrent scrubber reflects some of these advantages. EPRI funded TVA to perform preliminary screening tests of TVA's 1 MW pilot plant (Colbert Steam Plant) to develop operating data on the cocurrent design for use in designing and operating a 10 MW prototype cocurrent scrubber at TVA's Shawnee Scrubber Test Facility. Results of the Colbert tests showed excellent sulfur dioxide removal efficiencies, generally greater than 85%, low pressure drop, and high particulate removal efficiencies. This report covers these screening tests.

  12. Integration of advanced oxidation processes at mild conditions in wet scrubbers for odourous sulphur compounds treatment. (United States)

    Vega, Esther; Martin, Maria J; Gonzalez-Olmos, Rafael


    The effectiveness of different advanced oxidation processes on the treatment of a multicomponent aqueous solution containing ethyl mercaptan, dimethyl sulphide and dimethyl disulphide (0.5 mg L(-1) of each sulphur compound) was investigated with the objective to assess which one is the most suitable treatment to be coupled in wet scrubbers used in odour treatment facilities. UV/H2O2, Fenton, photo-Fenton and ozone treatments were tested at mild conditions and the oxidation efficiency obtained was compared. The oxidation tests were carried out in magnetically stirred cylindrical quartz reactors using the same molar concentration of oxidants (hydrogen peroxide or ozone). The results show that ozone and photo-Fenton are the most efficient treatments, achieving up to 95% of sulphur compounds oxidation and a mineralisation degree around 70% in 10 min. Furthermore, the total costs of the treatments taking into account the capital and operational costs were also estimated for a comparative purpose. The economic analysis revealed that the Fenton treatment is the most economical option to be integrated in a wet scrubber to remove volatile organic sulphur compounds, as long as there are no space constraints to install the required reactor volume. In the case of reactor volume limitation or retrofitting complexities, the ozone and photo-Fenton treatments should be considered as viable alternatives. Copyright © 2014 Elsevier Ltd. All rights reserved.

  13. Oxidation of North Dakota scrubber sludge for soil amendment and production of gypsum. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hassett, D.J.; Moe, T.A.


    Cooperative Power`s Coal Creek Station (CCS) the North Dakota Industrial Commission, and the US Department of Energy provided funds for a research project at the Energy and Environmental Research Center. The goals of the project were (1) to determine conditions for the conversion of scrubber sludge to gypsum simulating an ex situ process on the laboratory scale; (2) to determine the feasibility of scaleup of the process; (3) if warranted, to demonstrate the ex situ process for conversion on the pilot scale; and (4) to evaluate the quality and handling characteristics of the gypsum produced on the pilot scale. The process development and demonstration phases of this project were successfully completed focusing on ex situ oxidation using air at low pH. The potential to produce a high-purity gypsum on a commercial scale is excellent. The results of this project demonstrate the feasibility of converting CCS scrubber sludge to gypsum exhibiting characteristics appropriate for agricultural application as soil amendment as well as for use in gypsum wallboard production. Gypsum of a purity of over 98% containing acceptable levels of potentially problematic constituents was produced in the laboratory and in a pilot-scale demonstration.

  14. Strategies for enhancing the co-removal of mercury in FGD-scrubbers of power plants. Operating parameters and additives

    Energy Technology Data Exchange (ETDEWEB)

    Schuetze, Jan; Koeser, Heinz [Magdeburg Univ. (Germany). Chair of Environmental Technology; Halle-Wittenberg Univ., Halle (Germany). Centre of Engineering Services


    Co-combustion of waste fuels, coals with variable mercury content and lower regulatory emission limits are drivers for the optimisation of the co-removal of mercury in flue gas desulphurisation (FGD) scrubbers. The paper explains some new features of the system performance of FGD scrubbers for the co-removal of mercury in coal-fired power plants. Results on their efficiency under standardised laboratory conditions are presented. The effect of these measures on the quality of the FGD by-product gypsum will be covered as well. (orig.)

  15. Performance of geotextile-gravel bed all-weather surfaces


    Wachenfelt, Hans von


    A cost-effective way of producing all-weather surfaces for cattle is to use a combined geotextile-gravel pad construction, which allows pavement depth to be reduced. This study sought to determine the pavement construction that would offer the least runoff, best drainage effect and highest quality runoff and drainage effluent after exposure to heavy precipitation under different manure loads in high animal density areas. The study also examined whether any pavement construction gave acceptabl...

  16. Comparison of different forms of gravel as aggregate in concrete

    Directory of Open Access Journals (Sweden)

    Sikiru ORITOLA


    Full Text Available Gradation plays an important role in the workability, segregation, and pump ability of concrete. Uniformly distributed aggregates require less paste which will also decrease bleeding, creep and shrinkage while producing better workability, more durable concrete and higher packing. This attempt looks at the effect of particle size distribution pattern for five types of gravel aggregate forms, angular, elongated, smooth rounded, irregular and flaky as related to the strength of concrete produced. Different forms of naturally existing gravel aggregate were collected from a particular location and tests were carried out on them to determine their gradation. Based on the gradation the aggregates were used to prepare different samples of grade 20 concrete with water-cement ratio of 0.5. The particle size distribution resulted in coefficients of uniformity ranging from 1.24 to 1.44. The granite aggregate, which serves as a reference, had a coefficient of uniformity of 1.47. Tests were conducted on fresh and hardened concrete cube samples. The concrete sample CT5 recorded a slump of 32mm and highest compressive strength value of 21.7 N/mm2, among the concrete produced from different forms of gravel.

  17. Laboratory study of gravel-bed cluster formation and disintegration (United States)

    Heays, K. G.; Friedrich, H.; Melville, B. W.


    Increased knowledge of clusters is essential for the understanding of sediment transport behavior and the monitoring and protection of aquatic life. A physical study using graded river gravels is conducted in a laboratory environment. Using photogrammetry and painted gravels, a cluster identification tool (CIT) is developed based on image subtraction between subsequent frames, allowing identification of any stable areas and groups of particles on the bed. This is combined with digital particle tracking (DPT) to present a novel approach for monitoring the formation and disintegration of clusters. Clusters from graded gravels are formed successfully during the experimental stage, allowing investigation into the complex dynamic behavior of cluster formation and disintegration in a simulated natural environment. Various anchor stone arrangements are used in the experiments. However, only about one fifth of the potential anchor stones on the bed surface enable cluster formation. In general, clusters classified as "typical" and "heap" are most common. Inspection of temporal cluster coverage of the test-bed surface shows that the proportion of clusters present on the surface tends to grow with time. Maximum cluster surface coverage of between 5% and 34% is observed. In addition, particles entering and departing from clusters are monitored. Most commonly, particles enter from directly upstream of the cluster, however >20% of particles approach from a direction >20 deg from the streamwise direction. Approximately 35% of all particles directly upstream of a cluster bypass the cluster.

  18. Evidence for aeolian origins of heuweltjies from buried gravel layers

    Directory of Open Access Journals (Sweden)

    Michael D. Cramer


    Full Text Available Although heuweltjies (19–32 m diameter dominate the surface of much of the southwestern Cape of South Africa, their origins, distribution and age remain controversial. Current hypotheses are that the heuweltjies are (1 constructed by the excavation and mounding habits of burrowing animals; (2 the result of erosion by water of areas between patches protected from fluvial action by denser vegetation or (3 the product of localised aeolian sediment accumulation beneath denser vegetation associated with termitaria. At a site where quartz-containing gravels occur on the soil surface in areas between heuweltjies, these gravels were found to extend as a relatively intact layer of uniform concentration from the inter-mound area into the mound at the same plane as the surrounding soil surface. This buried layer suggests that heuweltjies were either built-up by deposition on a previous soil surface layer or eroded from sediment accumulated above the buried gravel layer. Mounds contain a relatively large proportion of silt consistent with sediment deposition. Mound sediment elemental composition was strongly correlated with that of local shale, indicating a local source of sediment. Pedogenesis was considerably more advanced off- than on-mound. There was no evidence of extensive regional aeolian sediment mantling over the vast area in which the heuweltjies occur. These findings and observations support the aeolian deposition hypothesis of heuweltjie origins combined with a degree of erosion, rather than a termite bioturbation hypothesis or a predominantly erosion-based hypothesis.

  19. Deschutes River Spawning Gravel Study, Volume I, Final Report.

    Energy Technology Data Exchange (ETDEWEB)

    Huntington, Charles W.


    Spawning habitat in the Deschutes River was inventoried, gravel permeability and composition were sampled at selected gravel bars, historical flow records for the Deschutes were analyzed, salmon and trout utilization of spawning habitat was examined, and potential methods of enhancing spawning habitat in the river were explored. Some changes in river conditions since the mid-1960's were identified, including a reduction in spawning habitat immediately downstream from the hydroelectric complex. The 1964 flood was identified as a factor which profoundly affected spawning habitat in the river, and which greatly complicated efforts to identify recent changes which could be attributed to the hydrocomplex. A baseline on present gravel quality at both chinook and steelhead spawning areas in the river was established using a freeze-core methodology. Recommendations are made for enhancing spawning habitat in the Deschutes River, if it is independently determined that spawning habitat is presently limiting populations of summer steelhead or fall chinook in the river. 53 refs., 40 figs., 21 tabs.

  20. Evolution of completion tools gravel pack systems for deep water

    Energy Technology Data Exchange (ETDEWEB)

    Pineda, Francisco [BJ Services Company, Houston, TX (United States); Vilela, Alvaro; Montanha, Roberto; Hightower, Chad; Acosta, Marco; Farias, Rodrigo [BJ Services do Brasil Ltda., Rio de Janeiro, RJ (Brazil)


    Conventional gravel pack or frac pack completions typically require the use of wash pipe to act as a conduit for fluid returns as well as to carry a shifting mechanism to open or close a return port. Using properly sized wash pipe can enhance the placement of the gravel across the entire annular space and the formation. It can also be used in conjunction with a shifting mechanism and a sliding sleeve to force the fluid returns to pass through the bottom of the screen. It can allow a wash-down capability while running the assembly into an open hole. In specialty systems, it can even act as a pumping conduit for post-gravel pack stimulation. However, the use of wash pipe, especially in long horizontal wells, means the loss of valuable rig time due to make up and break out of the wash pipe, or recovery if the wash pipe is stuck. Economic considerations, along with completion efficiencies, are especially important on deep water completions. Not using wash pipe reduces rig time, generating significant cost savings, and also eliminates the risk of a fishing operation. This paper reviews conventional wash pipe applications and describes new systems that accomplish the same goal with a minimum amount of wash pipe or no wash pipe at all. (author)

  1. Pump Coastdown with the Submerged Flywheel

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Hyun-Gi; Seo, KyoungWoo; Kim, Seong Hoon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    Many research reactors are generally designed as open pool types in consideration of the heat removal of the nuclear fuels, reactor operation and accessibility. Reactor structure assembly is generally placed at the pool bottom as shown in Fig. 1. Primary cooling system pump circulates the coolant from the reactor structure to the heat exchanger in order to continuously remove the heat generated from the reactor core in the research reactor as shown in Fig. 1. The secondary cooling system releases the transferred heat to the atmosphere by the cooling tower. Coastdown flow rate of the primary cooling system pump with the submerged flywheel are calculated analytically in case of the accident situation. Coastdown flow rate is maintained until almost 80 sec when the pump stops normally. But, coastdown flow rate is rapidly decreased when the flywheel is submerged because of the friction load on the flywheel surface.

  2. Coastline Protection by a Submerged Breakwater (United States)

    Valentine, B. D.; Hayatdavoodi, M.; Ertekin, R. C.


    Coastal communities are in danger of the impact caused by storm surge and waves. Storm surge brings the water level to a higher elevation and farther inland. This rise in water level increases the chance of a higher number and larger set of waves approaching shorelines, and it can potentially devastate the coastal infrastructure. In this study, we evaluate the performance of a submerged, horizontal breakwater located near shore. Unlike other types of breakwaters, such as the ones that extend to the surface, either fixed or floating, a submerged horizontal breakwater does not create any visual distraction or limit most of the recreational and commercial activities in the nearshore areas. The Level I Green-Naghdi (GN) nonlinear water wave equations are utilized here to study the wave transformation over a submerged breakwater that is located in shallow water. The GN theory is based on the theory of directed fluid sheets and assumes an incompressible and inviscid fluid; no assumption on the rotationality of the flow is required. In this approach, the nonlinear boundary conditions and the averaged conservation laws are satisfied exactly. The reflection and transmission coefficients due to nonlinear shallow water waves are determined implementing two approaches which use Goda's (1976) and Grue's (1992) methods. The results are compared with the existing laboratory experiments, and close agreement is observed overall. Preliminary results of the performance of the breakwater on dissipating storm waves during Hurricane Ike (2008), approaching the shore of Galveston, Texas, are presented.

  3. Introducing a new formula based on an artificial neural network for prediction of droplet size in venturi scrubbers

    Directory of Open Access Journals (Sweden)

    A. Sharifi


    Full Text Available Droplet size is a fundamental parameter for Venturi scrubber performance. For many years, the correlations proposed by Nukiyama and Tanasawa (1938 and Boll et al. (1974 were used for calculating mean droplet size in Venturi scrubbers with limited operating parameters. This study proposes an alternative approach on the basis of artificial neural networks (ANNs to determine the mean droplet size in Venturi scrubbers, in a wide range of operating parameters. Experimental data were used to design the ANNs. A neural network was trained based on the liquid to gas ratio (L/G and throat gas velocity (Vgth, as input parameters, and the Sauter mean diameter (D32 as the desired parameter. The back-propagation learning algorithms were used in the network and the best approach was found. A new formula for the prediction of D32 using the weights of the network was then generated. This formula predicts mean droplet size in Venturi scrubbers more accurately than the correlations of Boll et al. (1974 and Nukiyama and Tanasawa (1938. The Average Absolute Percent Deviation (AAPD of our formula and the Boll et al. and Nukiyama and Tanasawa correlations for the full ranges of experimental data are 26.04%, 40.19% and 32.99%, respectively.


    A 5-week series of pilot-scale incineration tests, employing a synthetic waste feed, was performed at the U.S. Environmental Protection Agency's Incineration Research Facility to evaluate the fate of trace metals fed to a rotary kiln incinerator equipped with a venturi scrubber/p...

  5. Semi-mechanistic modelling of ammonia absorption in an acid spray wet scrubber based on mass balance (United States)

    A model to describe reactive absorption of ammonia (NH3) in an acid spray scrubber was developed as a function of the combined overall mass transfer coefficient K. An experimental study of NH3 absorption using 1% dilute sulphuric acid was carried out under different operating conditions. An empiric...

  6. Chemistry of flyash scrubber sludge components in plant-soil-water systems

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Y.


    Flyash scrubber sludge (FASS) is a by-product from coal combustion at power plants. Land application and burial beneath wetlands have been suggested as more cost efficient disposal methods than burial in old mines. The FASS from the Associated Electric Power Plant at Thomas Hill, MO was added, 2.5 or 5.0% FASS by weight, to an acidic topsoil. FASS increased soil pH and salt level, and increased growth of alfalfa (Medicago sativa L.), birdsfoot trefoil (Lotus corniculatus L.) and tall fescue (Festuca aroundinacea L.). Concentrations of Al, Ba, Ca, Cd, Cu, Fe, K, Mg, Ni, P, Si, Sr, Ti, and Zn in plant tissues were either unaffected or reduced due to FASS addition. The concentrations of B, Cl, Mo, Mn, and S were higher in tissues of plants grown on FASS treated than untreated soil. Boron content limited the amount of FASS that could be applied to soil.

  7. Removal of acetaldehyde gas using wet scrubber coupled with photo-Fenton reaction

    Directory of Open Access Journals (Sweden)

    Masahiro Tokumura


    Full Text Available The feasibility of the combined air-cleaning method, which consisted of a wet scrubber and the photo-Fenton reaction, in the removal of gaseous acetaldehyde was evaluated. An acetaldehyde-gas removal efficiency of 99% was achieved in the one-pass test (residence time of 17 s using an inlet acetaldehyde-gas concentration of 1000 ppb at an initial total-iron-ion concentration of 50 mg L−1 and initial hydrogen peroxide concentration of 630 mg L−1. Even at the low initial total-iron-ion concentration of 4 mg L−1, a removal efficiency of 92% was achieved. The acetaldehyde removal efficiency was relatively independent of the initial hydrogen peroxide concentration. UV irradiation further augmented the rate of the photo-Fenton reaction leading to enhanced acetaldehyde-gas removal.

  8. Novel Adsorbent-Reactants for Treatment of Ash and Scrubber Pond Effluents

    Energy Technology Data Exchange (ETDEWEB)

    Bill Batchelor; Dong Suk Han; Eun Jung Kim


    The overall goal of this project was to evaluate the ability of novel adsorbent/reactants to remove specific toxic target chemicals from ash and scrubber pond effluents while producing stable residuals for ultimate disposal. The target chemicals studied were arsenic (As(III) and As(V)), mercury (Hg(II)) and selenium (Se(IV) and Se(VI)). The adsorbent/reactants that were evaluated are iron sulfide (FeS) and pyrite (FeS{sub 2}). Procedures for measuring concentrations of target compounds and characterizing the surfaces of adsorbent-reactants were developed. Effects of contact time, pH (7, 8, 9, 10) and sulfate concentration (0, 1, 10 mM) on removal of all target compounds on both adsorbent-reactants were determined. Stability tests were conducted to evaluate the extent to which target compounds were released from the adsorbent-reactants when pH changed. Surface characterization was conducted with x-ray photoelectron spectroscopy (XPS) to identify reactions occurring on the surface between the target compounds and surface iron and sulfur. Results indicated that target compounds could be removed by FeS{sub 2} and FeS and that removal was affected by time, pH and surface reactions. Stability of residuals was generally good and appeared to be affected by the extent of surface reactions. Synthesized pyrite and mackinawite appear to have the required characteristics for removing the target compounds from wastewaters from ash ponds and scrubber ponds and producing stable residuals.


    Directory of Open Access Journals (Sweden)

    S. Iu. Panov


    Full Text Available Summary. The article executed the feasibility study of various options for gas treatment. Rapid development of industry and transport worldwide in recent times raises the problem in the protection of habitat environment from harmful waste. In solving problems of flue gas treatment great attention is given to the economic characteristics and recycling techniques for capturing emissions and disposal must also meet the sanitary health requirements: flue gas treatment plants should not cause air or water pollution. The set objective is solved by developing a two-stage wet treatment system for pyrolysis gas based on ejector scrubbers. Their advantage - a central nozzle supply that allows the scrubber to operate on the principle of an ejector pump. Projected plant can be used in enterprises for processing of solid domestic and industrial waste, where there are steam and hot water boilers, whose operations result in contaminated gases emissions obtained with high temperatures. In particular, this installation can be applied at a cement plant in which a large amount of waste gases containing sulfur oxides is emitted. Assessment of market potential for the plant designed to treat waste gases in the cement factory is performed through a SWOT analysis. SWOT analysis results indicate the possibility of the treatment of exhaust gases without a high cost and with high gas treatment efficiency. Plant competitive analysis was done using an expert method in comparison with market competitors. Technical and economic indicators of the plant are presented. Return on investments is 46% and payback period of capital investments - 2.7 years.

  10. Reversal in Migration of Gravel-Sand Transition (United States)

    Kim, W.


    Downstream lithofacies change is an important key to interpret fluviodeltaic depositional environment, which can be recognized by lithologic features, such as grain-size. It has been generally accepted that changes in the downstream position of grain-size transition (e.g., gravel-sand transition) are attributed to variations in basinal forcing (e.g., climate variation, sea-level change and basin subsidence), factors that also cause shoreline migration. However, no quantitative model for predicting evolution of fluviodeltaic strata thoroughly incorporates lithofacies boundaries and allows their free individual migrations. In this presentation, I present a delta evolution model to provide the quantitative understanding of the relationship between the external moving boundary (delta shoreline) and the internal moving boundaries (grain-size transitions). By treating internal coarse to fine grain-size transitions as moving boundaries, the model is capable of accurately predicting the dynamic interactions between the upstream river reaches with different dominant grain-sizes and the downstream shoreline migration in response to base-level changes. For simplicity, the model employs one grain-size transition between the upstream gravel-bed reach and the downstream sand-bed reach and constant rates of water discharge, sediment supply, and relative sea-level rise. Test runs with ranges of sediment supply rates and relative sea-level rise rates show cases for retreat of the gravel-sand transition while the shoreline is still prograding, and thus reveal the condition for reversal in migration of the internal grain-size boundary against the direction of a growing fluviodeltaic system. The model can be used to provide baseline conditions for uniform migration direction of both internal lithofacies transitions and shoreline in fluviodeltaic systems that can be used to accurately assess the trajectory of grain-size transition in sedimentary strata as a proxy for environmental

  11. Sand and gravel mine operations and reclamation planning using microcomputers

    Energy Technology Data Exchange (ETDEWEB)

    Ariffin, J.B.


    The purpose of this study is to focus on the application of microcomputers, also known as personal computers, in planning for sand and gravel mine operations and reclamation at a site in Story County, Iowa. This site, called the Arrasmith Pit, is operated by Martin Marietta Aggregates, Inc. The Arrasmith site, which encompasses an area of about 25 acres, is a relatively small site for aggregate mining. However, planning for the concurrent mine operation and reclamation program at this site is just as critical as with larger sites and the planning process is the same.

  12. Submergence tolerance in Hordeum marinum

    DEFF Research Database (Denmark)

    Pedersen, Ole; Malik, Al I.; Colmer, Timothy D.


    Floodwaters differ markedly in dissolved CO(2), yet the effects of CO(2) on submergence responses of terrestrial plants have rarely been examined. The influence of dissolved CO(2) on underwater photosynthesis and growth was evaluated for three accessions of the wetland plant Hordeum marinum Huds......) movement, would all contribute to submergence tolerance in H. marinum. The present study demonstrates that dissolved CO(2) levels can determine submergence tolerance of terrestrial plants. So, submergence experiments should be conducted with defined CO(2) concentrations and enrichment might be needed...

  13. Simulating the role of gravel on the dynamics of permafrost on the Qinghai-Tibetan Plateau (United States)

    Yi, S.; Chen, J.; Wu, Q.; Ding, Y.


    Gravel (particle size ≥ 2 mm) is common in soil profiles of the Qinghai-Tibetan Plateau (QTP). It has different thermal and hydrological properties than other fine mineral soils (particle size thermal and hydrological processes of soil. However, few models have considered gravel. In this study, we implemented the thermal and hydraulic properties of gravel into the Dynamic Organic Soil-Terrestrial Ecosystem Model to develop new schemes to simulate the dynamics of permafrost on the QTP. Results showed that: (1) the widely used Farouki thermal scheme always simulated higher thermal conductivity of frozen soils than unfrozen soils with the same soil water content; therefore it tends to overestimate permafrost thickness strongly; (2) there exists a soil moisture threshold, below which the new set of schemes with gravel simulated smaller thermal conductivity of frozen soils than unfrozen soils; (3) soil with gravel has higher hydraulic conductivity and poorer water retention capability; and simulations with gravel were usually drier than those without gravel; and (4) the new schemes simulated faster upward degradation than downward degradation; and the simulated permafrost thicknesses were sensitive to the fraction of gravel, the gravel size, the thickness of soil with gravel, and the subsurface drainage. To reduce the uncertainties in the projection of permafrost degradation on the QTP, more effort should be made to: (1) developing robust relationships between soil thermal and hydraulic properties and gravel characteristics based on laboratory work; and (2) compiling spatial datasets of the vertical distribution of gravel content based on measurements during drilling or the digging of soil pits.

  14. Calibration of submerged multi-sluice gates

    Directory of Open Access Journals (Sweden)

    Mohamed F. Sauida


    The main objective of this work is to study experimentally and verify empirically the different parameters affecting the discharge through submerged multiple sluice gates (i.e., the expansion ratios, gates operational management, etc.. Using multiple regression analysis of the experimental results, a general equation for discharge coefficient is developed. The results show, that the increase in the expansion ratio and the asymmetric operation of gates, give higher values for the discharge coefficient. The obtained predictions of the discharge coefficient using the developed equations are compared to the experimental data. The present developed equations showed good consistency and high accuracy.

  15. Scientific Bases of Innovation Technology of Drill-Hole Equipment by Cryogenic-Gravel Filters

    Directory of Open Access Journals (Sweden)

    Коzhevnikov, А.А.


    Full Text Available Manufacturing technologies of cryogenic-gravel filter element and equipment of drill-hole water receiving part by a cryogenic-gravel filter are described. Compoundings of mineral binder and cryogenically-gravel composition are substantiated. Patterns of physical fields influence on the change of their properties and technological operations of equipping drill-hole water receiving part on changes of physical, mechanical, thermal and technological properties of experimental cryogenic gravel filter element are established. Parameters of delivery technology of cryogenicgravel filter to drill-hole water receiving part are theoretically and experimentally worked out.

  16. Damage detection in submerged plates using ultrasonic guided waves

    Indian Academy of Sciences (India)

    Suitable ultrasonic guided wave modes with optimum scanning capabilities have been generated and identified in submerged plate system. Finally, the propagation of selected modes through submerged notched plates is investigated. Sensitivity of leaky waves to the notches has been studied. The methodology would help ...

  17. Automating a submerged pump method for operating oil wells

    Energy Technology Data Exchange (ETDEWEB)

    Popa, I.


    The basic parameters of wells which operate in a mode of submerged operation are presented. The basic systems for measuring and testing the parameters of submerged operation are described. Worldwide experience in solving this particular problem is analyzed. Romanian (SRR) use of systems for automation, remote signaling and remote management is examined.

  18. Impacts of climate change on submerged and emergent wetland plants (United States)

    Frederick T. Short; Sarian Kosten; Pamela A. Morgan; Sparkle L Malone; Gregg E. Moore


    Submerged and emergent wetland plant communities are evaluated for their response to global climate change (GCC), focusing on seagrasses, submerged freshwater plants, tidal marsh plants, freshwater marsh plants and mangroves. Similarities and differences are assessed in plant community responses to temperature increase, CO2increase, greater UV-B exposure, sea...

  19. Identification of a novel submergence response gene regulated by ...

    African Journals Online (AJOL)

    Tuoyo Aghomotsegin


    Dec 7, 2016 ... 3Engineering Research Center of Ecology and Agricultural Use of Wetland, Ministry of Education, Yangzte University,. Jingzhou 434025, P.R. .... intolerance to submergence) and M202(Sub1A) by qRT-. PCR. We identified a novel gene responsive to submergence, called RS1. The expression patterns of.

  20. Identification of a novel submergence response gene regulated by ...

    African Journals Online (AJOL)

    Our results also show that RS1 is highly expressed under submergence, drought, and NaCl stresses, but not under cold or dehydration stress. Hormone ABA treatment induces, whereas GA treatment decreases, RS1 expression. The RS1 and Sub1A genes are co-regulated under submergence. Overexpression of RS1 in ...

  1. Gravel road stabilisation of Ehnsjoevaegen, Hallstavik[Using fly ash]; Skogsbilvaegsrenovering av Ehnsjoevaegen, Hallstavik

    Energy Technology Data Exchange (ETDEWEB)

    Macsik, Josef; Svedberg, Bo [Ecoloop, Stockholm (Sweden)


    Fly ash in geotechnical applications has stabilising, isolating, low permeability and hardening effect. Fly ash can be used in road constructions with low bearing capacity, as well as on top cover material on landfills. The aim of the project was to build a road section with fly ash stabilised gravel, based on laboratory studies, and follow up technical and environmental aspect during the first year after stabilisation. The overall aim of this project was to evaluate fly ash from Holmen Paper, Hallstavik, from technical and environmental point of view in a gravel road construction. A gravel road, Ehnsjoevaegen, was stabilised with fly ash during autumn 2004. This road was a low priority road. The fly ash stabilised road section was 1300 m long. Gravel from the road Ehnsjoevaegen was stabilised and investigated in a laboratory study. Leachability of metals and geotechnical aspects were investigated. The laboratory study showed that fly ash stabilised gravel has high shear strength, however its thawing resistance is not fully acceptable. Additives of cement or merit are needed in order to increase its thawing resistance. The actual road section is not going to be used during thawing period and no additives were used. The test road is divided into different sections including a reference section. The road stabilisation work was conducted with gravel transported to Ehnsjoevaegen from off site and not with gravel from the site. Fly ash was tipped off on a levelled road, followed by tipping of gravel. Mixing fly ash and gravel was done on site by a road scraper. After the mixing the road was gravelled with 0,1 m graded gravel. In this project the fly ash had low water content. In order to get optimal compaction water was added from a tanker supplying water before compacted with a compactor. Results from the pilot test shows that fly ash stabilised gravel can be tipped, mixed and compacted effectively. Tipping can be optimised if fly ash and gravel is mixed in a mixer

  2. Quantifying Stream Bed Gravel Mobility from Friction Angle Measurements (United States)

    Meyers, M. A.; Dunne, T.


    A method to measure friction angles using force gauges was field tested to determine its utility at quantifying critical shear stress in a gravel bedded reach of the San Joaquin River in California. Predictions of mobility from friction angles were compared with observations of the movement of tagged particles from locations for which local shear stress was quantified with a validated 2-D flow model. The observations of movement, distance of travel, and location of the end of travel were made after extended flow releases from Friant dam. Determining the critical shear stress for gravel bed material transport currently depends upon bedload sampling or tracer studies. Often, such measurements can only be made during occasional and untimely flow events, and at limited, suboptimal locations. Yet, theoretical studies conclude that the friction angle is an important control on the critical shear stress for mobility of any grain size, and therefore of the excess shear stress which strongly influences bedload transport rate. The ability to predict bed mobility at ungauged and unmonitored locations is also an important requirement for planning of flow regimes and channel design. Therefore, a method to measure friction angles that can be performed quickly in low flow conditions would prove useful for river management and research. To investigate this promising method friction angle surveys were performed at two riffle sites where differences in bed material size and distribution, and channel slope were observed. The friction angle surveys are sensitive enough to detect differences between the sites as well as spatially and temporally within a single riffle. Low friction angles were observed along the inside of a long bend where sand content was greater (by ~20%) than other surveyed locations. Friction angles decreased slightly after a depositional event associated with transient large woody debris and bank erosion, and increased again after a 5 year return interval flow

  3. Application of Structure from Motion (SfM) Photogrammetry to Quantify Gravel Storage Following Gravel Augmentation, Oak Grove Fork of the Clackamas River, Oregon (United States)

    Curran, M. L.; Hales, G.; Michalak, M.


    Digital Terrain Models (DTMs) generated in Agisoft Photoscan from photogrammetry provide a basis for a high resolution, quantitative analysis of geomorphic features that are difficult to describe using conventional, commonly used techniques. Photogrammetric analysis can be particularly useful in investigating the spatial and temporal dispersal of gravel in high gradient mountainous streams. The Oak Grove Fork (OGF), located in northwestern Oregon, is one of the largest tributaries to the Clackamas River. Lake Harriet Dam and diversion was built on the OGF in 1924 as part of a hydroelectric development by Portland General Electric. Decreased flow and sediment supply downstream of Lake Harriet Dam has resulted in geomorphic and biological changes, including reduced salmonid habitat. As part of a program to help restore a portion of the natural sediment supply and improve salmonid habitat, gravel augmentation is scheduled to begin September 2016. Tracking the downstream movement of augmented gravels is crucial to establishing program success. The OGF provides a unique setting for this study; flow is regulated at the dam, except for spillover during high flow events, and a streamflow gaging station downstream of the study area reports discharge. As such, the controlled environment of the OGF provides a natural laboratory to study how a sediment-depleted channel responds geomorphically to a known volume of added gravel. This study uses SfM to evaluate deposition of the augmented gravel following its introduction. The existing channel is characterized by coarse, angular gravel, cobble, and boulder; the augmented gravel is finer, rounded, and 5% of the volume is an exotic lithology to provide a visual tracer. Baseline, pre-gravel introduction DTMs are constructed and will be differenced with post-gravel introduction DTMs to calculate change at four study sites. Our preliminary pilot testing on another river shows that centimeter-scale accretion and aggradation within the

  4. Assessment of NH3 Reduction and N2O Production during Treatment of Exhausted Air from Fattening Pigs Building by a Commercial Scrubber


    Loyon, L.; Dupard, P.; Saint Cast, P.; Guiziou, F.


    International audience; The use of air scrubbers to reduce ammonia (NH3) emissions from buildings on pig farms is one of the most promising techniques in the Göteborg protocol and other European regulations including the Industrial Emission Directive. In France, some air scrubbers are currently used on pig farms, mainly to reduce odours from livestock buildings. However, recent research revealed the production of N2O resulting from the treatment of air from pig buildings. In this context, a t...

  5. A study of the sand and gravel deposits around the permanent site ...

    African Journals Online (AJOL)

    A geophysical investigation of the sand and gravel deposits at the Federal University of Technology Owerri was carried out using the vertical electrical sounding (VES) approach. The aim of the study was to determine the occurrences and depths of sand and gravel deposits at the study area. This was done using the ...

  6. Evaluation of an ion adsorption method to estimate intragravel flow velocity in salmonid spawning gravels (United States)

    James L. Clayton; John G. King; Russell F. Thurow


    Intragravel water exchange provides oxygenated water, removes metabolic waste, and is an essential factor in salmonid embryo survival. Measurements of intragravel flow velocity have been suggested as an index of gravel quality and also as a useful predictor of fry emergence; however, proposed methods for measuring velocity in gravel are problematic. We evaluate an ion...

  7. Manual for computing bed load transport using BAGS (Bedload Assessment for Gravel-bed Streams) Software (United States)

    John Pitlick; Yantao Cui; Peter Wilcock


    This manual provides background information and instructions on the use of a spreadsheet-based program for Bedload Assessment in Gravel-bed Streams (BAGS). The program implements six bed load transport equations developed specifically for gravel-bed rivers. Transport capacities are calculated on the basis of field measurements of channel geometry, reach-average slope,...

  8. Bedload pulses in a hydropower affected alpine gravel bed river (United States)

    Aigner, Johann; Kreisler, Andrea; Rindler, Rolf; Hauer, Christoph; Habersack, Helmut


    This study investigated the sediment resupply and transport dynamics at the Upper Drau River upstream of Lienz (Eastern Tyrol, Austria). Due to a hydropower plant, a 24 km long river reach of this alpine gravel bed river is under residual flow conditions, although sediment is still resupplied into the reach through many active torrents and tributaries. As a result, sediment deposition in the residual flow reach intensified, hence increasing maintenance efforts to stabilize this river section and ensure flood protection. In combination with a new sediment management program, a continuous bedload monitoring system was installed 2 km downstream of the residual reach in 2001 to support the development of adapted sediment management strategies. The surrogate bedload monitoring system consists of 16 impact plate geophones, installed over a 17 m wide cross section. The unprecedented 15-year dataset of high-resolution bedload intensity revealed a complex process of gravel storage and intermittent resupply from the residual reach, allowing the authors a detailed analysis of frequently occurring bedload pulses. These transport features are triggered by increased discharges during floods in the residual reach and created pronounced anticlockwise bedload hysteresis or, with a temporal shift to the event peak, caused distinct shifts in the bedload activity downstream. Bedload pulses produce very high bedload fluxes while in transit, tend to increase bedload flux in the post-event phase, and can alter and reduce the upstream sediment storage leading to a lowering of bedload availability for future pulses. The observed time lags between main discharge events and the arrival of the macro-pulses are correlated with mean water discharge during pulse propagation, thus enabling a prediction of the pulse arrival at the monitoring station solely based on the hydrograph. In combination with the hydrological setup of the reach, the observed bedload pulse time lags allowed an estimation of

  9. Evaluation of a Full-Scale Water-Based Scrubber for Removing Siloxanes from Digester Gas: A Case Study. (United States)

    Surita, Sharon C; Tansel, Berrin


    Siloxanes are becoming more prominent in digester gas at water resource recovery facilities because of their wide use in personal care products. This study evaluates a full-scale water-based scrubber operating in a water resource recovery facility (Miami, FL). The digester gas is used for energy generation due to its high methane content. During energy generation, siloxanes are converted to silicates and Silicon Dioxide (SiO2), which leave deposits on engine components. Trimethylsilanol (TMSOH), Octamethyltrisiloxane (L3), Hexamethylcyclotrisiloxane (D3), Octamethylcyclotetrasiloxane (D4), Decamethylcyclopentasiloxane (D5), and Dodecamethylcyclohexasiloxane (D6) were detected in the digester gas. D4 and D5 were present at the highest concentrations, 5000 and 1800 μg/ m3, respectively. Sampling results have indicated that scrubbers employed for hydrogen sulfide (H2S) removal at the facility do not provide effective removal of siloxanes due to their high Henry's Constant. Post scrubber treatment is needed to remove siloxanes from the digester gas prior to combustion.

  10. Laser-matter Interaction with Submerged Samples

    Energy Technology Data Exchange (ETDEWEB)

    Mariella, R; Rubenchik, A; Norton, M; Donohue, G; Roberts, K


    With the long-term goal in mind of investigating if one could possibly design a 'universal solid-sample comminution technique' for debris and rubble, we have studied pulsed-laser ablation of solid samples that were contained within a surrounding fluid. Using pulses with fluences between 2 J and 0.3 J, wavelengths of 351 and 527 nm, and samples of rock, concrete, and red brick, each submerged in water, we have observed conditions in which {micro}m-scale particles can be preferentially generated in a controlled manner, during the laser ablation process. Others have studied laser peening of metals, where their attention has been to the substrate. Our study uses non-metallic substrates and analyzes the particles that are ablated from the process. The immediate impact of our investigation is that laser-comminution portion of a new systems concept for chemical analysis has been verified as feasible.

  11. Submerged arc welding of heavy plate (United States)

    Wilson, R. A.


    The submerged arc process is particularly suitable for heavy plate welding because of its ability to combine very high deposit rates along with excellent quality. It does these things without the smoke and spatter often accompanying other processes. It is available today in several forms that are pointed to the fabricators of heavy sections with long, short or round about welds. Tandem arc full automatic equipment is particularly suitable for those long heavy welds where speed and deposit rate are of the first order. An attachment called long stick-out which makes use of the IR drop on long electrode extensions can be included on this equipment to increase deposition rates 50% or more.

  12. Modeling tabular icebergs submerged in the ocean (United States)

    Stern, A. A.; Adcroft, A.; Sergienko, O.; Marques, G.


    Large tabular icebergs calved from Antarctic ice shelves have long lifetimes (due to their large size), during which they drift across large distances, altering ambient ocean circulation, bottom-water formation, sea-ice formation, and biological primary productivity in the icebergs' vicinity. However, despite their importance, the current generation of ocean circulation models usually do not represent large tabular icebergs. In this study, we develop a novel framework to model large tabular icebergs submerged in the ocean. In this framework, tabular icebergs are represented by pressure-exerting Lagrangian elements that drift in the ocean. The elements are held together and interact with each other via bonds. A breaking of these bonds allows the model to emulate calving events (i.e., detachment of a tabular iceberg from an ice shelf) and tabular icebergs breaking up into smaller pieces. Idealized simulations of a calving tabular iceberg, its drift, and its breakup demonstrate capabilities of the developed framework.

  13. Crassulacean acid metabolism in submerged aquatic plants (United States)

    Keeley, Jon E.; Sybesme, C.


    CO2-fixation in the dark is known to occur in various organs of many plants. However, only in species possessing crassulacean acid metabolism (CAM) does dark CO2-fixation contribute substantially to the carbon economy of the plant. Until very recently CAM was known only from terrestrial species, largely drought adapted succulents. The discovery of CAM in the submerged aquatic fern ally Isoetes howellii (Isoetaceae)(Keeley 1981) adds a new dimension to our understanding of crassulacean acid metabolism. In this paper I will summarize 1) the evidence of CAM in Isoetes howellii, 2) the data on the distribution of CAM in aquatic species, and 3) the work to date on the functional significance of CAM in aquatic species.

  14. Evaluation of Decontamination Factor of Aerosol in Pool Scrubber according to Bubble Shape and Size

    Energy Technology Data Exchange (ETDEWEB)

    Jo, Hyun Joung; Ha, Kwang Soon; Jang, Dong Soon [KAERI, Daejeon (Korea, Republic of)


    The scrubbing pool could play an important role in the wet type FCVS because a large amount of aerosol is captured in the water pool. The pool scrubbing phenomena have been modelled and embedded in several computer codes, such as SPARC (Suppression Pool Aerosol Removal Code), BUSCA (BUbble Scrubbing Algorithm) and SUPRA (Suppression Pool Retention Analysis). These codes aim at simulating the pool scrubbing process and estimating the decontamination factors (DFs) of the radioactive aerosol and iodine gas in the water pool, which is defined as the ratio of initial mass of the specific radioactive material to final massy after passing through the water pool. The pool scrubbing models were reviewed and an aerosol scrubbing code has been prepared to calculate decontamination factor through the pool. The developed code has been verified using the experimental results and parametric studies the decontamination factor according to bubble shape and size. To evaluate the decontamination factor more accurate whole pool scrubber phenomena, the code was improved to consider the variety shape and size of bubbles. The decontamination factor were largely evaluated in ellipsoid bubble rather than in sphere bubble. The pool scrubbing models will be enhanced to apply more various model such as aerosol condensation of hygroscopic. And, it is need to experiment to measure to bubble shape and size distribution in pool to improve bubble model.

  15. CO2 Capture and Crystallization of Ammonia Bicarbonate in a Lab-Scale Scrubber

    Directory of Open Access Journals (Sweden)

    Pao Chi Chen


    Full Text Available A lab-scale bubble-column scrubber is used to capture CO2 gas and produce ammonia bicarbonate (ABC using aqueous ammonia as an absorbent under a constant pH and temperature. The CO2 concentration is adjusted by mixing N2 and CO2 in the range of 15–60 vol % at 55 °C. The process variables are the pH of the solution, temperature, gas-flow rate and the concentration of gas. The effects of the process variables on the removal efficiency (E, absorption rate (RA and overall mass-transfer coefficient (KGa were explored. A multiple-tube mass balance model was used to determine RA and KGa, in which RA and KGa were in the range of 2.14 × 10−4–1.09 × 10−3 mol/(s·L and 0.0136–0.5669 1/s, respectively. Results found that, RA showed an obvious increase with the increase in pH, inlet gas concentration and gas temperature, while KGa decreased with an increase in inlet gas concentration. Using linear regression, an empirical expression for KGa/E was obtained. On the other hand, ammonia bicarbonate crystals could be produced at a pH of 9.5 when the gas concentration was higher than 30% and γ (=Fg/FA, the gas-liquid molar flow rate ratio ≥ 1.5.

  16. Workshop on ROVs and deep submergence (United States)

    The deep-submergence community has an opportunity on March 6 to participate in a unique teleconferencing demonstration of a state-of-the-art, remotely operated underwater research vehicle known as the Jason-Medea System. Jason-Medea has been developed over the past decade by scientists, engineers, and technicians at the Deep Submergence Laboratory at Woods Hole Oceanographic Institution. The U.S. Navy, the Office of the Chief of Naval Research, and the National Science Foundation are sponsoring the workshop to explore the roles that modern computational, communications, and robotics technologies can play in deep-sea oceanographic research.Through the cooperation of Electronic Data Systems, Inc., the Jason Foundation, and Turner Broadcasting System, Inc., 2-1/2 hours of air time will be available from 3:00 to 5:30 PM EST on March 6. Twenty-seven satellite downlink sites will link one operating research vessel and the land-based operation with workshop participants in the United States, Canada, the United Kingdom, and Bermuda. The research ship Laney Chouest will be in the midst of a 3-week educational/research program in the Sea of Cortez, between Baja California and mainland Mexico. This effort is focused on active hydrothermal vents driven by heat flow from the volcanically active East Pacific Rise, which underlies the sediment-covered Guaymas Basin. The project combines into a single-operation, newly-developed robotic systems, state-of-the-art mapping and sampling tools, fiber-optic data transmission from the seafloor, instantaneous satellite communication from ship to shore, and a sophisticated array of computational and telecommunications networks. During the workshop, land-based scientists will observe and participate directly with their seagoing colleagues as they conduct seafloor research.

  17. Submerged membrane distillation for seawater desalination

    KAUST Repository

    Francis, Lijo


    A submerged membrane distillation (SMD) process for fresh water production from Red Sea water using commercially available hollow fiber membranes has been successfully employed and compared with the conventional direct contact membrane distillation (DCMD) process. The hollow fiber membranes have been characterized for its morphology using field effect scanning electron microscope. In SMD process, a bunch of hollow fiber membranes are glued together at both ends to get a simplified open membrane module assembly submerged into the coolant tank equipped with a mechanical stirrer. Hot feed stream is allowed to pass through the lumen side of the membrane using a feed pump. Continuous stirring at the coolant side will reduce the temperature and concentration polarization. During the conventional DCMD process, using feed-coolant streams with co-current and counter-current flows has been tested and the results are compared in this study. In SMD process, a water vapor flux of 10.2 kg m-2 h-1 is achieved when using a feed inlet temperature of 80°C and coolant temperature of 20°C. Under the same conditions, during conventional DCMD process, a water vapor flux of 11.6 and 10.1 kg m-2 h-1 were observed during counter-current and co-current flow streams, respectively. Results show that the water production in the SMD process is comparable with the conventional DCMD process, while the feed-coolant flow streams are in the co-current direction. During conventional DCMD operation, a 15% increase in the water production is observed when feed-coolant streams are in the counter-current direction compared to the co-current direction. © 2014 © 2014 Balaban Desalination Publications. All rights reserved.

  18. Streamwise decrease of the 'unsteady' virtual velocity of gravel tracers (United States)

    Klösch, Mario; Gmeiner, Philipp; Habersack, Helmut


    Gravel tracers are usually inserted and transported on top of the riverbed, before they disperse vertically and laterally due to periods of intense bedload, the passage of bed forms, lateral channel migration and storage on bars. Buried grains have a lower probability of entrainment, resulting in a reduction of overall mobility, and, on average, in a deceleration of the particles with distance downstream. As a consequence, the results derived from tracer experiments and their significance for gravel transport may depend on the time scale of the investigation period, complicating the comparison of results from different experiments. We developed a regression method, which establishes a direct link between the transport velocity and the unsteady flow variables to yield an 'unsteady' virtual velocity, while considering the tracer slowdown with distance downstream in the regression. For that purpose, the two parameters of a linear excess shear velocity formula (the critical shear velocity u*c and coefficient a) were defined as functions of the travelled distance since the tracer's insertion. Application to published RFID tracer data from the Mameyes River, Puerto Rico, showed that during the investigation period the critical shear velocity u*c of tracers representing the median bed particle diameter (0.11 m) increased from 0.36 m s-1 to 0.44 m s-1, while the coefficient a decreased from the dimensionless value of 4.22 to 3.53, suggesting a reduction of the unsteady virtual velocity at the highest shear velocity in the investigation period from 0.40 m s-1 to 0.08 m s-1. Consideration of the tracer slowdown improved the root mean square error of the calculated mean displacements of the median bed particle diameter from 8.82 m to 0.34 m. As in previous work these results suggest the need of considering the history of transport when deriving travel distances and travel velocities, depending on the aim of the tracer study. The introduced method now allows estimating the

  19. Durability performance of submerged concrete structures - phase 2. (United States)


    This project determined that severe corrosion of steel can occur in the submerged : portions of reinforced concrete structures in marine environments. Field studies of decommissioned : pilings from Florida bridges revealed multiple instances of stron...

  20. Submerged Aquatic Vegetation of Bogue Sound, North Carolina 1992 Geodatabase (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — During 1992, 1:20,000 scale aerial photography for Bogue Sound, North Carolina was collected as part of an effort to map submerged aquatic vegetation (SAV) in...

  1. Submerged Aquatic Vegetation of Bogue Sound, North Carolina 1992 Substrate (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — During 1992, 1:20,000 scale aerial photography for Bogue Sound, North Carolina was collected as part of an effort to map submerged aquatic vegetation (SAV) in...

  2. Marine algal flora of submerged Angria Bank (Arabian Sea)

    Digital Repository Service at National Institute of Oceanography (India)

    Untawale, A.G.; Reddy, C.R.K.; Ambiye, V.

    Submerged Angria Bank was surveyed for the deep water marine algal flora. About 57 species were reported from this bank for the first time. Rhodophyta dominated (30 species) followed by Chlorophyta (18 species) and Phaeophyta (9 species). A few...

  3. Submerged Aquatic Vegetation of Bogue Sound, North Carolina 1992 Biotic (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — During 1992, 1:20,000 scale aerial photography for Bogue Sound, North Carolina was collected as part of an effort to map submerged aquatic vegetation (SAV) in...

  4. Submerged Aquatic Vegetation of Bogue Sound, North Carolina 1992 Geoform (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — During 1992, 1:20,000 scale aerial photography for Bogue Sound, North Carolina was collected as part of an effort to map submerged aquatic vegetation (SAV) in...

  5. Compliance problems solved by ethylene oxide scrubber at specialty gas plant

    Energy Technology Data Exchange (ETDEWEB)


    A specialty gas producer was confronted with an EPA compliance problem in dealing with ethylene oxide (EtO). The chemical had been added to the toxicity lists of the US EPA and the Occupational Safety and Health Administration (OSHA). Effective August 21, 1984, the OSHA standard for EtO limited exposure to a 1 ppm, eight-hour time weighted average. Ethylene oxide is used to sterilize many pharmaceutical and hospital supplies. Typically, EtO is supplied in cylinders as a mixture with Freon-12 or carbon dioxide. A standard cylinder contains 135 lb of product, of which about 16 lb is EtO. When a customer is finished with an EtO cylinder, it is returned to the specialty gas producer. Before recharging a cylinder, it must be purged of any remaining EtO and then cleaned. The purged EtO presented a problem in removal and disposal. An ethylene oxide scrubbing system was designed for the gas cylinder area. It consists of a specially designed 28 ft packed tower, a 400 gal holding tank, valves, and recirculation pump. Gas purged from returned EtO cylinders is directed to the scrubber and is channelled upward through the packed bed as scrubbing liquid flows countercurrently over the packing. A mist eliminator at the top of the packed bed prevents entrained liquids from escaping with the vent gas. The water soluble EtO is hydrolized to ethylene alcohol and then to ethylene glycol, a relatively inert and harmless chemical.

  6. Selection of amine combination for CO2 capture in a packed bed scrubber

    Directory of Open Access Journals (Sweden)

    Aruna Singh


    Full Text Available This investigation was to test different blends of tertiary amine; triethanolamine (TEA into primary amine; Monoethanolamine (MEA used to capture CO2 in packed bed scrubber with recycle stream. Four different operating parameters: Amine Combination (A, Dilution Water (B, Liquid Flow rate (C, and Gas Flow rate (D were varied to study the behavior of the system. Moreover, Taguchi method was employed to establish the order of importance of different parameters in the process. A 4 factor and 3 level was chosen for the study and it was explored using L9 (34 orthogonal array design. According to 3-level design 0%, 20% and 30% were chosen for A, 10%, 20% and 30% for B, 1 Lmin−1, 1.5 Lmin−1 and 2 Lmin−1 for C, 8 Lmin−1, 16 Lmin−1 and 20 Lmin−1 for D. To understand the effectiveness order of different operating parameters, three factors namely Absorption efficiency (E, Absorption Rate (RA, and Scrubbing Factor (E were calculated upon which the order was compared. The highest efficiency of 92.2% was achieved with 20% TEA. However, with 30% of TEA and 20% solvent mix maximum scrubbing factor (E of 0.63 mol-CO2/mol-Solvent was achieved. As per Taguchi analysis the significance sequence for absorption efficiency (ϕ was B > C > D > A; for absorption rate C > B > D > A and for scrubbing factor it was C > B > D > A. The blending of tertiary amine seemed advantageous for carbon dioxide capture process.

  7. The effect of coarse gravel on cohesive sediment entrapment in an annular flume (United States)

    Glasbergen, K.; Stone, M.; Krishnappan, B.; Dixon, J.; Silins, U.


    While cohesive sediment generally represents a small fraction (under the maximum applied shear stresses (1.11 Pa) used in the experiment. The gravel bed had an entrapment coefficient (ratio between the entrapment flux and the settling flux) of 0.2. Accordingly, when flow conditions are sufficient to produce a shear stress that will mobilize the armour layer of the gravel bed (>16 Pa), cohesive materials trapped within the gravel bed will be entrained and transported into the Glenmore Reservoir, where sediment-associated nutrients may pose treatment challenges to the drinking water supply.

  8. Sea Dredged Gravel versus Crushed Granite as Coarse Aggregate for Self Compacting Concrete in Aggressive Environment

    DEFF Research Database (Denmark)

    Sørensen, Eigil V.; Kristensen, Lasse Frølich


    Properties of self compacting concrete (SCC) with two types of coarse aggregate - sea dredged gravel with smooth and rounded particles and crushed granite with rough and angular particles - have been studied. Sea gravel allowed a higher aggregate proportion in the concrete leading to a higher...... modulus of elasticity. Tensile and compressive strength were found to depend both on aggregate type and on the properties of the interfacial zone close to the aggregate surface. Freeze-thaw scaling resistance was good with crushed granite, whereas sea gravel led to more severe scaling caused by porphyry...

  9. Impeded Carbohydrate Metabolism in Rice Plants under Submergence Stress

    Directory of Open Access Journals (Sweden)

    Malay Kumar ADAK


    Full Text Available The detrimental effects of submergence on physiological performances of some rice varieties with special references to carbohydrate metabolisms and their allied enzymes during post-flowering stages have been documented and clarified in the present investigation. It was found that photosynthetic rate and concomitant translocation of sugars into the panicles were both related to the yield. The detrimental effects of the complete submergence were recorded in generation of sucrose, starch, sucrose phosphate synthase and phosphorylase activity in the developing panicles of the plants as compared to those under normal or control (i.e. non-submerged condition. The accumulation of starch was significantly lower in plants under submergence and that was correlated with ADP-glucose pyrophosphorylase activity. Photosynthetic rate was most affected under submergence in varying days of post-flowering and was also related to the down regulation of Ribulose bisphosphate carboxylase activity. However, under normal or control condition, there recorded a steady maintenance of photosynthetic rate at the post-flowering stages and significantly higher values of Ribulose bisphosphate carboxylase activity. Still, photosynthetic rate of the plants under both control and submerged conditions had hardly any significant correlation with sugar accumulation and other enzymes of carbohydrate metabolism like invertase with grain yield. Finally, plants under submergence suffered significant loss of yield by poor grain filling which was related to impeded carbohydrate metabolism in the tissues. It is evident that loss of yield under submergence is attributed both by lower sink size or sink capacity (number of panicles, in this case as well as subdued carbohydrate metabolism in plants and its subsequent partitioning into the grains.

  10. Incipient motion of sediment in presence of submerged flexible vegetation


    Wang, Hao; Tang, Hong-Wu; Zhao, Han-Qing; Xuan-yu ZHAO; Lü, Sheng-qi


    The presence of submerged vegetation on river beds can change the water flow structure and alter the state of sediment motion. In this study, the incipient motion of sediment in the presence of submerged flexible vegetation in open channels was investigated in a laboratory experiment. The vegetation was simulated with flexible rubber cylinders arranged in parallel arrays. The effect of the vegetation density, water depth, and sediment grain size on the incipient motion was investigated. The e...

  11. Analysis of the Blasting Compaction on Gravel Soil

    Directory of Open Access Journals (Sweden)

    Qingwen Li


    Full Text Available The settlement control is critical for the safety of road based on high filled embankment. The traditional construction methods have the characteristic with less soil thickness compacted at a time. There are many advantages to compact the gravel soil with blasting. The cavity in soil is formed by blasting and its fillings to form a composite foundation for the embankment. The field data show this composite foundation can meet the requirement of loading and settlement control with less construction time. In geotechnical blasting, the high temperature due to blasting will swell the material around, so its worthy to do the coupled analysis with thermal mechanics (TM and blasting compaction in the high filled embankment. In this paper, a 3D model is built with FLAC3D to simulate a single hole to predict the range and degree of thermal propagation. Then, the thermal strains got from the model are used to estimate the displacement of surrounding soil to predict the degree of compaction and optimize the distribution of blast holes in plan.

  12. Roughness coefficient and its uncertainty in gravel-bed river

    Directory of Open Access Journals (Sweden)

    Ji-Sung Kim


    Full Text Available Manning's roughness coefficient was estimated for a gravel-bed river reach using field measurements of water level and discharge, and the applicability of various methods used for estimation of the roughness coefficient was evaluated. Results show that the roughness coefficient tends to decrease with increasing discharge and water depth, and over a certain range it appears to remain constant. Comparison of roughness coefficients calculated by field measurement data with those estimated by other methods shows that, although the field-measured values provide approximate roughness coefficients for relatively large discharge, there seems to be rather high uncertainty due to the difference in resultant values. For this reason, uncertainty related to the roughness coefficient was analyzed in terms of change in computed variables. On average, a 20% increase of the roughness coefficient causes a 7% increase in the water depth and an 8% decrease in velocity, but there may be about a 15% increase in the water depth and an equivalent decrease in velocity for certain cross-sections in the study reach. Finally, the validity of estimated roughness coefficient based on field measurements was examined. A 10% error in discharge measurement may lead to more than 10% uncertainty in roughness coefficient estimation, but corresponding uncertainty in computed water depth and velocity is reduced to approximately 5%. Conversely, the necessity for roughness coefficient estimation by field measurement is confirmed.

  13. Behavior of a gravel-sand material on cyclic way

    Directory of Open Access Journals (Sweden)

    hocine bendadouche


    Full Text Available This article has the results of the cyclic triaxial compression tests to study the potential of liquefaction of a gravel-sand material.  The last part is devoted to the not drained cyclic tests and their analyses.  Many articles are devoted to the tests on the standard sand of laboratory Hostun in particular for the study of liquefaction or on reconstituted clays but few tests are carried out on a natural material.  The scarcity of cyclic tests on such rough natural materials shows the difficulty of assessing the seismic risk. Faced with these difficulties, the use of tests such as the CPT provides a different but very practical approach. The overall results show a trend of relatively high liquefaction of the material, even under conditions of moderate stress (qc / 2s'3 = 0.2. This trend is growing very strongly when the rate of cyclic loading reached 0.3. The CPT test also shows a great tendency to liquefaction with a safety factor of well below 1.


    Directory of Open Access Journals (Sweden)

    Santamarina Juan Carlos


    Full Text Available The exact determination of seismic waves' propagation velocities has great importance in the geotechnics due to from that it is possible to determine, among other parameters, the dynamic ones: Elasticity E, Rigidity G, Poisson !, compressibility B; as well as to reach a knowledge on the stress-strain behavior for the studied soil samples. The seismic waves transmission considered in tests at laboratory scale carried out in the present work is a phenomenon that produces very small deformation, and so doesn't disturb the material. This allows
    to apply the results in a more general scale to study the behavior of soils in situ and to predict their answer to stress.
    With the purpose to study the response of particulate material subjected to seismic excitements at small scale, samples of gravels and sands were successively introduced in an odometric cell, exciting them with impulsive signals and registering the corresponding seismograms through general purpose piezoelectric transducers embedded in ends of the cell.
    The distance source-receiver was interval increased, which enabled, from the corresponding regression straight lines, to calculate in precise form the propagation velocities (for P waves.
    The tests were carried out in samples of dry alluvial soil with three different grain sizes. The respective frequency spectra of the signals were determined for two packing modes: loose and compact, what added information on the medium characteristics.

  15. Integrated automatic and continuous bedload monitoring in gravel bed rivers (United States)

    Habersack, Helmut; Kreisler, Andrea; Rindler, Rolf; Aigner, Johann; Seitz, Hugo; Liedermann, Marcel; Laronne, Jonathan B.


    Bedload monitoring techniques have been developed and applied for many years in rivers ranging from steep mountain torrents to the large gravel-bed Danube River in Austria. Most monitoring stations use a combination of direct (mobile bag samplers, slot samplers) and indirect (geophones, hydrophones) measurement methods. Each individual technique is adequate, yet features particular boundary conditions and limitations related to hydraulic and sampling efficiency, functionality during floods, sampling duration or grain size. We show the capabilities and limitations of the different monitoring devices with respect to technical, operational and economic criteria, evaluating their suitability for determining bedload transport parameters. Bedload monitoring results of a measuring site at the Drau River in Carinthia/Austria are used to illustrate the specific range of the device application. We present an integrated automatic and continuous bedload monitoring system. It complements the specific limitations of single monitoring methods by additional measurement devices, enabling comprehensive monitoring of the bedload transport process. We then derive the Bedload Discharge Integrated Calculation Approach and the Bedload Rating Curve Approach and discuss their application for determining bedload discharge Qb and total bedload mass Vb. Whereas the integrated approach combines data from direct monitoring methods with indirect techniques, the rating curve approach uses only data from direct bedload monitoring devices. We demonstrate that applying an integrated automatic and continuous bedload monitoring system and combining the Bedload Discharge Integrated Calculation Approach and Bedload Rating Curve Approach yields accurate bedload discharge results.

  16. Factors Affecting the Mechanical Properties of Cement-Mixed Gravel

    Directory of Open Access Journals (Sweden)

    Chen Wang


    Full Text Available A study has been conducted to investigate the mechanical properties of cement-mixed gravel using the unconfined compression test and the tensile test. Basic factors including the curing period, the water-binder ratio, the cement content, and the strain rate were evaluated. Ordinary Portland cement with fly ash was employed as the cementation agent for preparing cemented samples. The results indicate that the unconfined compressive strength, the deformation modulus, and the tensile strength increase with the increase in the curing period. The ratio of tensile strength to unconfined compressive strength has no distinct change after 7 days. An optimum water-binder ratio can be obtained. The unconfined compressive strength and deformation modulus decrease as the water-binder ratio decreases and increase from the optimum water-binder ratio. With the increasing of the cement content, the unconfined compressive strength increases distinctly, the deformation modulus increases significantly when the cement content is less than 4% and then increased slowly, and the failure strain increases to a peak value and then decreases. With the increasing of the strain rate, the unconfined compressive strength increases slightly and the deformation modulus increases slowly. The failure strain decreases with an increase in the strain rate.

  17. Heat transfer model for quenching by submerging

    Energy Technology Data Exchange (ETDEWEB)

    Passarella, D N; Varas, F [Departamento de Matematica Aplicada II, E.T.S. de Ing. de Telecomunicacion, Universidad de Vigo, Campus Marcosende, 36310 Vigo (Spain); MartIn, E B, E-mail:, E-mail:, E-mail: [Area de Mecanica de Fluidos, E.T.S. de Ing. Industriales, Universidad de Vigo, Campus Marcosende, 36310 Vigo (Spain)


    In quenching by submerging the workpiece is cooled due to vaporization, convective flow and interaction of both mechanisms. The dynamics of these phenomena is very complex and the corresponding heat fluxes are strongly dependent on local flow variables such as velocity of fluid and vapor fraction. This local dependence may produce very different cooling rates along the piece, responsible for inappropriate metallurgical transformations, variability of material properties and residual stresses. In order to obtain an accurate description of cooling during quenching, a mathematical model of heat transfer is presented here. The model is based on the drift-flux mixture-model for multiphase flows, including an equation of conservation of energy for the liquid phase and specific boundary conditions that account for evaporation and presence of vapor phase on the surface of the piece. The model was implemented on Comsol Multiphysics software. Generation of appropriate initial and boundary conditions, as well as numerical resolution details, is briefly discussed. To test the model, a simple flow condition was analyzed. The effect of vapor fraction on heat transfer is assessed. The presence of the typical vapor blanket and its collapse can be recovered by the model, and its effect on the cooling rates on different parts of the piece is analyzed. Comparisons between numerical results and data from literature are made.

  18. Influence of vegetation and gravel mesh on the tertiary treatment of wastewater from a cosmetics industry. (United States)

    Vlyssides, Apostolos G; Mai, Sofia T H; Barampouti, Elli Maria P; Loukakis, Haralampos N


    To estimate the influence of gravel mesh (fine and coarse) and vegetation (Phragmites and Arundo) on the efficiency of a reed bed, a pilot plant was included after the wastewater treatment plant of a cosmetic industry treatment system according to a 22 factorial experimental design. The maximum biochemical oxygen demand (BOD5), chemical oxygen demand (COD) and total phosphorous (TP) reduction was observed in the reactor, where Phragmites and fine gravel were used. In the reactor with Phragmites and coarse gravel, the maximum total Kjeldahl nitrogen (TKN) and total suspended solids (TSS) reduction was observed. The maximum total solids reduction was measured in the reed bed, which was filled with Arundo and coarse gravel. Conclusively, the treatment of a cosmetic industry's wastewater by reed beds as a tertiary treatment method is quite effective.

  19. Federal Outer Continental Shelf (OCS) Sand and Gravel Borrow Areas (Lease Areas) (United States)

    Bureau of Ocean Energy Management, Department of the Interior — Federal outer Continental Shelf (OCS) Sand and Gravel Borrow Areas (Lease Areas) are polygons which are maintained by the Bureau of Ocean Energy Management (BOEM),...

  20. Minor NSR Permit: Crossfire Aggregate Services, LLC - Crossfire Bonds Gravel Pit (United States)

    This page contains the response to public comments and final minor NSR permit for the Crossfire Bonds Gravel Pit, operated by Crossfire Aggregate Services, LLC, and located on the Southern Ute Indian Reservation in La Plata County, Colorado.

  1. Sand and Gravel Company in Central Mass. to Reduce Emissions Under Settlement with EPA (United States)

    In a settlement with the USEPA, Kimball Sand, a sand & gravel company operating in the MA communities of Blackstone & Northborough, agreed to reduce its emissions of hazardous air pollutants & visible emissions as required by federal clean air laws.


    Methods for determining small-scale variations in aquifer properties were investigated for a sand and gravel aquifer on Cape Cod, Massachusetts. easurements of aquifer properties, in particular hydraulic conductivity, are needed for further investigations into the effects of aqui...

  3. Which tributaries disrupt downstream fining along gravel-bed rivers? (United States)

    Rice, Stephen


    Tributaries and other lateral sediment sources can have a significant impact on river bed sediment texture and, in turn, on channel form. Sufficiently voluminous or distinct sediment inputs redefine the mainstem grain-size distribution, punctuating downstream maturation and isolating a sequence of discrete sedimentary links. Within these links fining processes usually dominate, such that models of sorting and abrasion, when applied to individual links, provide reasonable predictions of grain-size change. Links represent the fundamental natural unit within which fining models can be tested, developed and applied. Identification of significant lateral sources is therefore important, yet, beyond vague references to relative tributary size, sediment load, and sediment calibre, no criteria exist for the a priori discrimination of such sources. In this paper a procedure for identifying significant lateral (tributary) sources, without the benefit of grain-size information, is outlined. A high-resolution characterisation of bed material texture along two Canadian gravel-bed rivers facilitated classification of all their perennial tributaries as either significant or insignificant. Three absolute tributary basin parameters and their relative counterparts, chosen to reflect the likely controls on tributary significance, are then used to develop a discriminant function which isolates a large proportion of significant tributaries while minimising incorrect classifications. Examination of consistently misclassified (anomalous) tributaries reveals the importance of lateral source spacing and of inconsistencies in the geomorphic history of the contributing basins. In turn, a general tributary categorisation procedure is suggested which includes a logistic regression model for attaching probability statements to individual classifications. The generality of the discriminant and logistic functions cannot be assessed because of the lack of other suitable data sets.

  4. Submerged cultivation of medicinal mushrooms: bioprocesses and products (review). (United States)

    Elisashvili, Vladimir


    Medicinal mushrooms belonging to higher Basidiomycetes are an immensely rich yet largely untapped resource of useful, easily accessible, natural compounds with various biological activities that may promote human well-being. The medicinal properties are found in various cellular components and secondary metabolites (polysaccharides, proteins and their complexes, phenolic compounds, polyketides, triterpenoids, steroids, alkaloids, nucleotides, etc.), which have been isolated and identified from the fruiting bodies, culture mycelium, and culture broth of mushrooms. Some of these compounds have cholesterol-lowering, anti-diabetic, antioxidant, antitumor, immunomodulating, antimicrobial, and antiviral activities ready for industrial trials and further commercialization, while others are in various stages of development. Recently, the submerged cultivation of medicinal mushrooms has received a great deal of attention as a promising and reproducible alternative for the efficient production of mushroom mycelium and metabolites. Submerged cultivation of mushrooms has significant industrial potential, but its success on a commercial scale depends on increasing product yields and development of novel production systems that address the problems associated with this technique of mushroom cultivation. In spite of many researchers' efforts for the production of bioactive metabolites by mushrooms, the physiological and engineering aspects of submerged cultures are still far from being thoroughly studied. The vast majority of studies have focused on polysaccharide and ganoderic acid production in submerged cultivation of medicinal mushrooms, and very little has been written so far on the antioxidant and hemagglutinating activity of submerged mushroom cultures. The purpose of this review is to provide an update of the present state of the art and future prospects of submerged cultivation of medicinal mushrooms to produce mycelium and bioactive metabolites, and to make a

  5. Interaction of Bar Morphology and Riparian Vegetation in Gravel-Bed Rivers (United States)

    Francalanci, S.; Bertoldi, W.; Siviglia, A.; Solari, L.; Toffolon, M.; Vetsch, D.


    Gravel-bed rivers are often characterized by complex bed topography, including single- and multiple-row alternate bars, bed undulations associated with channel curvature, riffle and pool sequences, presence of riparian vegetation in the floodplain, etc. The interaction of these features results in different morphologies with complex patterns and dynamics. The present work investigates the effect of the riparian vegetation on the bar dynamics, in particular it is investigated how the vegetation, which grows during the dry season on the bars, can alter the topographic patterns evolution during flood conditions. Performing two-dimensional numerical simulations we try to answer to the following research questions: which is the interaction of vegetation with bar morphology? which are the changes in sediment discharge and flow resistance, at cross-sectional and reach scale? Which are the changes in distribution of emerged and submerged areas, and potential feedbacks for vegetation growth? Which is the effect of vegetation on bar wave-length? The code BASEMENT (Faeh et al., 2010) has been used for performing the numerical runs. It has been properly modified in order to deal with the numerical description of the vegetation. The vegetation was allowed to grow during the dry season on the top of dry emergent areas, and the vertical distribution of vegetation in equilibrium condition was modeled as a function of the bed elevation using a simple analytical formulation, following Marani et al (2013). Then, during the flood events we assume that the vegetation distribution does not change, and that it can only be uprooted if the bed is eroded.The flow resistance was divided into a resistance exerted by the soil and a resistance exerted by the plants (Crosato and Saleh, 2010; Li and Millar, 2011); in this way it was possible to reproduce both the decrease in bed shear stress, reducing the sediment transport capacity of the flow within the plants, and the increase in hydraulic

  6. Analysis of a wet scrubber network in the air remediation of industrial workplaces: benefit for the city air quality

    CERN Document Server

    Avveduto, Alessandro; Pace, Lorenzo; Curci, Gabriele; Monaco, Alessio; De Giovanni, Marina; Giammaria, Franco; Spanto, Giuseppe; Tripodi, Paolo


    Industrial activities carried out in confined spaces are characterized by a very specific type of air pollution. The extended exposure to this kind of pollution is often highly harmful, resulting in dramatic effects both on health and safety aspects. The indoor industrial abatement systems, adopted to purify the air, are typically applied to the emission points. The processed air is subsequently emitted outside. In this study we present the experimental results of three-stage wet scrubber systems installed in the industrial workplace of a (i) fiberglass processing plant, where the highest exposure levels to volatile compounds are nowadays today monitored,and of a (ii) waste-to-energy plant, characterized by a very high particulate matter level. The adopted technology, to be used as complementing strategy,does not require special disposal procedures and the processed air is re-emitted in the same work environment for the benefit of the work operators. The operation of the scrubbers network during the working a...

  7. Rice SUB1A constrains remodelling of the transcriptome and metabolome during submergence to facilitate post-submergence recovery. (United States)

    Locke, Anna M; Barding, Gregory A; Sathnur, Sumukh; Larive, Cynthia K; Bailey-Serres, Julia


    The rice (Oryza sativa L.) ethylene-responsive transcription factor gene SUB1A-1 confers tolerance to prolonged, complete submergence by limiting underwater elongation growth. Upon desubmergence, SUB1A-1 genotypes rapidly recover photosynthetic function and recommence development towards flowering. The underpinnings of the transition from stress amelioration to the return to homeostasis are not well known. Here, transcriptomic and metabolomic analyses were conducted to identify mechanisms by which SUB1A improves physiological function over the 24 hr following a sublethal submergence event. Evaluation of near-isogenic genotypes after submergence and over a day of reaeration demonstrated that SUB1A transiently constrains the remodelling of cellular activities associated with growth. SUB1A influenced the abundance of ca. 1,400 transcripts and had a continued impact on metabolite content, particularly free amino acids, glucose, and sucrose, throughout the recovery period. SUB1A promoted recovery of metabolic homeostasis but had limited influence on mRNAs associated with growth processes and photosynthesis. The involvement of low energy sensing during submergence and recovery was supported by dynamics in trehalose-6-phosphate and mRNAs encoding key enzymes and signalling proteins, which were modulated by SUB1A. This study provides new evidence of convergent signalling pathways critical to the rapidly reversible management of carbon and nitrogen metabolism in submergence resilient rice. © 2017 John Wiley & Sons Ltd.

  8. Peculiarities of thermal dissociation of oxides during submerged arc welding

    Directory of Open Access Journals (Sweden)

    Leonid Zhdanov


    Full Text Available A method of settlement of the process of thermal dissociation of oxides in reaction zone during the submerged arc welding and welding deposition is presented. Combined non-linear equations for definition of gas-vapour mixture composition were developed. They describe the dissociation of MeO, MeO2 and Me2O3 types of oxides. Calculations of the processes of oxide dissociation were performed for the oxides that are commonly included into welding fluxes. Their results and analysis are presented. The method proposed appeared to be adequate and applicable for analysis of processes during submerged arc operation that run in the gas phase.

  9. EAARL-B Submerged Topography—Saint Croix, U.S. Virgin Islands, 2014 (United States)

    U.S. Geological Survey, Department of the Interior — A submerged topography digital elevation model (DEM) mosaic for a portion of the submerged environs of Saint Croix, U.S. Virgin Islands, was produced from remotely...

  10. EAARL-B Submerged Topography--Saint Thomas, U.S. Virgin Islands, 2014 (United States)

    U.S. Geological Survey, Department of the Interior — A submerged topography Digital Elevation Model (DEM) mosaic for a portion of the submerged environs of Saint Thomas, U.S. Virgin Islands, was produced from remotely...

  11. Long-term allelopathic control of phytoplankton by the submerged macrophyte Elodea nuttallii

    NARCIS (Netherlands)

    Vanderstukken, M.; Declerck, S.A.J.; Decaestecker, E.; Muylaert, K.


    Keywords: allelochemicals; chemical ecology; competition; nutrient limitation; shallow lakes Summary 1.It is well known that submerged macrophytes can suppress phytoplankton blooms in lakes and thus promote water quality and biodiversity. One of the possible mechanisms through which submerged

  12. Invasive Crayfish Threaten the Development of Submerged Macrophytes in Lake Restoration

    NARCIS (Netherlands)

    Wal, van der J.E.M.; Dorenbosch, M.; Immers, A.K.; Vidal Forteza, C.; Geurts Van Kessel, J.M.M.; Peeters, E.T.H.M.; Koese, B.; Bakker, E.S.


    Submerged macrophytes enhance water transparency and aquatic biodiversity in shallow water ecosystems. Therefore, the return of submerged macrophytes is the target of many lake restoration projects. However, at present, north-western European aquatic ecosystems are increasingly invaded by omnivorous

  13. Invasive crayfish threaten the development of submerged macrophytes in lake restoration

    NARCIS (Netherlands)

    Van der Wal, J.E.M.; Dorenbosch, M.; Immers, A.; Vidal Forteza, C.; Geurts, J.J.M.; Peeters, E.T.H.M.; Koese, B.; Bakker, E.S.


    Submerged macrophytes enhance water transparency and aquatic biodiversity in shallow water ecosystems. Therefore, the return of submerged macrophytes is the target of many lake restoration projects. However, at present, north-western European aquatic ecosystems are increasingly invaded by omnivorous

  14. Through-flow of water in leaves of a submerged plant is influenced by the apical opening

    DEFF Research Database (Denmark)

    Pedersen, Ole; Jørgensen, Lise Bolt; Sand-Jensen, Kaj


    Submerged plant, apical opening, hydathode, Sparganium, hydraulic architecture, leaf specific conductivity......Submerged plant, apical opening, hydathode, Sparganium, hydraulic architecture, leaf specific conductivity...

  15. Effect of percentage of low plastic fines on the unsaturated shear strength of compacted gravel soil

    Directory of Open Access Journals (Sweden)

    Kamal Mohamed Hafez Ismail Ibrahim


    Full Text Available Low plastic fines in gravel soils affect its unsaturated shear strength due to the contribution of matric suction that arises in micro and macro pores found within and between aggregates. The shear strength of five different types of prepared gravel soils is measured and is compared with a theoretical model (Fredlund et al., 1978 to predict the unsaturated shear strength. The results are consistent to a great extent except the case of dry clayey gravel soil. It is also found that on inundation of gravel soils containing plastic fines greater than 12% a considerable reduction in both the strength and the stiffness modulus is noticed. This 12% percentage is close to the accepted 15% percentage of fines given by ASTM D4318 (American society for testing material. The angle of internal friction that arises due to matric suction decreases with the increase of degree of saturation of soil. The hysteresis of some tested gravel soils is measured and found that it increases by increasing the percentage of fines.

  16. Modeling of fugitive dust emission for construction sand and gravel processing plant. (United States)

    Lee, C H; Tang, L W; Chang, C T


    Due to rapid economic development in Taiwan, a large quantity of construction sand and gravel is needed to support domestic civil construction projects. However, a construction sand and gravel processing plant is often a major source of air pollution, due to its associated fugitive dust emission. To predict the amount of fugitive dust emitted from this kind of processing plant, a semiempirical model was developed in this study. This model was developed on the basis of the actual dust emission data (i.e., total suspended particulate, TSP) and four on-site operating parameters (i.e., wind speed (u), soil moisture (M), soil silt content (s), and number (N) of trucks) measured at a construction sand and gravel processing plant. On the basis of the on-site measured data and an SAS nonlinear regression program, the expression of this model is E = 0.011.u2.653.M-1.875.s0.060.N0.896, where E is the amount (kg/ton) of dust emitted during the production of each ton of gravel and sand. This model can serve as a facile tool for predicting the fugitive dust emission from a construction sand and gravel processing plant.

  17. Ecological effects of scrubber water discharge on coastal plankton: Potential synergistic effects of contaminants reduce survival and feeding of the copepod Acartia tonsa

    DEFF Research Database (Denmark)

    Koski, Marja; Stedmon, Colin; Trapp, Stefan


    To meet the oncoming requirements for lower sulphur emissions, shipping companies can install scrubbers where the exhaust is sprayed with seawater and subsequently discharged to the sea. The discharge water has a pH around 3 and contains elevated concentrations of vanadium, nickel, lead and hydro......To meet the oncoming requirements for lower sulphur emissions, shipping companies can install scrubbers where the exhaust is sprayed with seawater and subsequently discharged to the sea. The discharge water has a pH around 3 and contains elevated concentrations of vanadium, nickel, lead...... and hydrocarbons. We investigated 1) the threshold concentrations of scrubber discharge water for survival, feeding and reproduction of the copepod Acartia tonsa, 2) whether the effects depend on the exposure route and 3) whether exposure to discharge water can be detected in field-collected organisms. A direct...... exposure to discharge water increased adult copepod mortality and reduced feeding at metal concentrations which were orders of magnitude lower than the lethal concentrations in previous single-metal studies. In contrast, reproduction was not influenced by dietary uptake of contaminants. Scrubber water...


    A series of pilot-scale incineration tests was performed at EPA's Incineration Research Facility (IRF) in Jefferson, Arkansas, to evaluate the fate of trace metals fed to a rotary kiln incinerator equipped with an ionizing wet scrubber (IWS) for particulate and acid gas control. ...


    A series of pilot-scale incineration tests was performed at EPA's Incineration Research Facility (IRF) in Jefferson, Arkansas, to evaluate the fate of trace metals fed to a rotary kiln incinerator equipped with an ionizing wet scrubber (IWS) for particulate and acid gas control. ...

  20. Hydrogen mitigation in submerged arc welding (United States)

    Klimowicz, Steven

    With the role of hydrogen in weld metal well understood in its relation to cold cracking, there has been a push to produce welds with lower and lower diffusible hydrogen contents. The push for lower diffusible hydrogen contents has placed pressure on consumables manufactures to create consumables that can achieve the requirements for lower diffusible hydrogen content. Currently EM12K flux is produced so that it can achieve below 4 ml of diffusible hydrogen for every 100g of weld metal deposited (ml/100g) for submerged arc welding (SAW). The recent trend for industry is to preferentially achieve diffusible hydrogen contents below 3 ml/100g. Making it necessary to find a way to modify the flux to achieve a lower diffusible hydrogen content for the welds it produces. To achieve this goal a two phase plan was developed. The first phase was to characterize the entire welding system for hydrogen. Since the goal of the project is hydrogen mitigation, any amount of hydrogen that could be reduced is helpful and therefore must first be discovered. Sources of hydrogen may be found by analyzing the welding wire and base metal, as well as breaking the flux down into its components and production steps. The wire was analyzed for total hydrogen content as was the base metal. The flux and its components were analyzed using differential thermal analysis-simultaneous thermal analysis (DTA-STA) and later vacuum degassing for moisture content. The analysis of the wire showed that the copper coating on the wire was the largest contributor of hydrogen. There was lubricant present on the wire surface as well, but it did not contribute as much as the copper coating. It was found that a simple low temperature baking of the wire was enough to remove the lubricant and coating moisture. The base metal was found to have a similar total hydrogen content to that of the wire. The breakdown of the flux and production process for moisture content analysis revealed that the production process

  1. Proposed gas generation assembly would recover deeply submerged objects (United States)

    Sprague, C. W.


    Gas generation system, used for recovery of submerged objects, generates hydrogen gas by the reaction of sodium with sea water. The assembly consists of flooded flotation tanks cabled together, equipped with relief valves to equalize pressure as the array ascends and hydrostatic pressure diminishes, and carrying remotely activated welding units.

  2. Implementation of Submerged Arc Welding Training. Final Report. (United States)

    Bowick, Earl; Todd, John

    A unit on submerged arc welding (SAW) was developed and integrated into the welding program at Seattle Central Community College (Washington) during the period December 1983 through May 1984. During this time, 10 major users of SAW in the area were contacted and mailed questionnaires. Follow up consisted of telephone calls and personal contact as…

  3. Benthic Bacterial Diversity in Submerged Sinkhole Ecosystems▿ † (United States)

    Nold, Stephen C.; Pangborn, Joseph B.; Zajack, Heidi A.; Kendall, Scott T.; Rediske, Richard R.; Biddanda, Bopaiah A.


    Physicochemical characterization, automated ribosomal intergenic spacer analysis (ARISA) community profiling, and 16S rRNA gene sequencing approaches were used to study bacterial communities inhabiting submerged Lake Huron sinkholes inundated with hypoxic, sulfate-rich groundwater. Photosynthetic cyanobacterial mats on the sediment surface were dominated by Phormidium autumnale, while deeper, organically rich sediments contained diverse and active bacterial communities. PMID:19880643

  4. Effects of submerged and anaerobic fermentations on cassava flour ...

    African Journals Online (AJOL)

    Oke Oluwatoyin Victoria


    Mar 18, 2015 ... Cassava tubers for processing into cassava flour, Lafun a Nigerian locally fermented product was subjected to two different types of fermentations: submerged and anaerobic fermentation for 72 h. Physicochemical changes that occurred during fermentation and their influence on the functional, rheological ...

  5. Reactive oxygen species mediate growth and death in submerged plants

    Directory of Open Access Journals (Sweden)

    Bianka eSteffens


    Full Text Available Aquatic and semi-aquatic plants are well adapted to survive partial or complete submergence which is commonly accompanied by oxygen deprivation. The gaseous hormone ethylene controls a number of adaptive responses to submergence including adventitious root growth and aerenchyma formation. Reactive oxygen species (ROS act as signaling intermediates in ethylene-controlled submergence adaptation and possibly also independent of ethylene. ROS levels are controlled by synthesis, enzymatic metabolism and nonenzymatic scavenging. While the actors are by and large known, we still have to learn about altered ROS at the subcellular level and how they are brought about, and the signaling cascades that trigger a specific response. This review briefly summarizes our knowledge on the contribution of ROS to submergence adaptation and describes spectrophotometrical, histochemical and live cell imaging detection methods that have been used to study changes in ROS abundance. Electron paramagnetic resonance (EPR spectroscopy is introduced as a method that allows identification and quantification of specific ROS in cell compartments. The use of advanced technologies such as EPR spectroscopy will be necessary to untangle the intricate and partially interwoven signaling networks of ethylene and ROS.

  6. Surface Intermediate Zone of Submerged Turbulent Buoyant Jet in Current

    DEFF Research Database (Denmark)

    Chen, H. B.; Larsen, Torben


    This paper deals with the intermediate zone between the jet and plume stages of a submerged buoyant discharge from sea outfall in current. The stability criteria, plume width and height after the intermediate zone and the dilution within the intermediate region have been studied theoretically and...

  7. Effects of prolonged elevated water salinity on submerged ...

    African Journals Online (AJOL)

    environmental change, global warming. * To whom all correspondence should be addressed. e-mail: Received 9 March 2017; accepted in revised form 10 October 2017. INTRODUCTION. Estuarine submerged macrophyte communities can be highly variable at both spatial and temporal scales, ...

  8. Protein enrichment of cassava peel by submerged fermentation ...

    African Journals Online (AJOL)



    Jan 11, 2010 ... Key words: Cassava peel, Trichoderma viride, enzyme, submerged fermentation, protein, amino acids. INTRODUCTION. Protein-energy malnutrition remains a major public health problem in many developing countries and there is the need to increase daily intake of protein, especially animal protein, using ...

  9. Relationships between the biomass of waterfowl and submerged ...

    African Journals Online (AJOL)

    The Wilderness Lakes system, comprising three estuarine lakes (Eilandvlei, Langvlei and Rondevlei), supports a diverse waterbird community, which includes 12 duck species and the abundant Red-knobbed Coot Fulica cristata. Biannual counts of waterfowl (ducks and Red-knobbed Coot) and assessments of submerged ...

  10. Protein enrichment of cassava peel by submerged fermentation with ...

    African Journals Online (AJOL)

    Protein enrichment of cassava peel by submerged fermentation with Trichoderma viride (ATCC 36316). OO Ezekiel, OC Aworh, HP Blaschek, TC Ezeji. Abstract. Cassava (Manihot esculenta Crantz) peel is one of the solid wastes produced as a consequence of cassava processing. It is low in protein but contains a large ...

  11. Nitrification in a submerged attached growth bioreactor using Luffa ...

    African Journals Online (AJOL)

    A laboratory-scale submerged attached growth bioreactor using Luffa cylindrica as support material for the immobilization of nitrifying bacteria was applied for polishing the effluent of an UASB reactor treating domestic wastewater under the tropical conditions of northeast Brazil, in the City of Campina Grande (7o 13' 11” ...

  12. Effects of submerged vegetation on water clarity across climates

    NARCIS (Netherlands)

    Kosten, S.; Lacerot, G.; Jeppesen, E.; Motta Marques, D.M.L.; Nes, van E.H.; Mazzeo, N.; Scheffer, M.


    A positive feedback between submerged vegetation and water clarity forms the backbone of the alternative state theory in shallow lakes. The water clearing effect of aquatic vegetation may be caused by different physical, chemical, and biological mechanisms and has been studied mainly in temperate

  13. Emissions from sludge incinerators with venturi and tray scrubbers and wet electrostatic precipitators: Metals, chromium and nickel compounds, and organics

    Energy Technology Data Exchange (ETDEWEB)

    Bostian, H.E.; DeWees, W.G.; Crumpler, E.P.; Lewis, F.M.


    A comprehensive test program was developed to determine the ratios of hexavalent to total chromium and nickel subsulfide to total nickel for a typical municipal wastewater sludge incinerator under normal combustion conditions and improved combustion conditions. Emissions of metals, hexavalent chromium, nickel subsulfide, polychlorinated dibenzodioxins and furans (PCDD/PCDFs), semi-volatile and volatile organic compounds, carbon monoxide (CO), and total hydrocarbons (THCs) from two multiple hearth incinerators and a fluidized bed incinerator were measured. The emissions were controlled at each unit with venturi scrubbers and, on two of the units, emissions from wet electrostatic precipitators (ESPs) were determined. Flue gas sampling was conducted at the inlet and outlet of the air pollution control devices at three separate sites. Gas concentrations, mass emission rates, metals-to-particulate ratios, and emissions factors were reported. Analytical results for the process samples were reported.

  14. Horizontal single-trip gravel pack and selective simulation system for deep water extended reach wells

    Energy Technology Data Exchange (ETDEWEB)

    Pineda, Francisco [BJ Services Company, Houston, TX (United States); Vilela, Alvaro; Montanha, Roberto; Acosta, Marco; Farias, Rodrigo [BJ Services do Brasil Ltda., Rio de Janeiro, RJ (Brazil)


    Most of the reservoirs located in the deep water and ultra-deep water offshore South America are described as unconsolidated sandstone that require sand control on both producers and water injection wells. Horizontal Open Hole Gravel Pack completions are the preferred method of development. If completing heavy oil reservoirs, there is a necessity of longer horizontal open hole sections. Low fracture gradients may limit the length of gravel pack in the open hole section because of the pressure increase during the Beta wave proppant deposition phase. This system allows the gravel pack assembly to be installed and the gravel pack to be pumped during the alpha and beta wave deposition phases without the limitation of high pressures that could fracture the well. The benefits of the Horizontal Single-Trip Gravel Pack and Selective Stimulation System (HSTSSS) using the differential valve include the ability to complete longer horizontal intervals, valuable rig-time savings and, efficient mechanical diversion of the stimulation fluid. This paper outlines the application of the HSTSSS system using a differential valve to complete a horizontal well in offshore deep waters. The need for a differential valve is primarily in horizontal gravel packing operations when normal circulating rates and pressures around the open hole would exceed formation break down pressure. The valve is intended to be easily spaced out and run in the wash pipe. At a predetermined differential pressure the valve opens and the return flow path distance around the bottom of the tailpipe is shortened, thus reducing back pressure preventing filter cake damage without slowing the pump rate. In addition the said valve has to close to allow the selective stimulation to take place. Economic considerations along with completion efficiencies are especially important on deep water, subsea completions. The utilization of differential valves allows completion of extended-reach open hole wells and/or low fracture

  15. Large-scale restoration of salmon spawning habitat in a regulated, gravel-bedded river (United States)

    Harrison, L.; Bray, E. N.; Overstreet, B. T.; Legleiter, C. J.; Dunne, T.


    Large-scale river restoration programs have recently emerged as a tool for improving salmon habitat in highly altered river ecosystems. Few studies have quantified the extent to which the restored habitat is utilized by salmonids, which physical processes contribute to improved biological functionality, or how the restored habitat changes over time. We investigated Pacific salmon spawning site utilization in two restored reaches of a gravel-bedded river: a site of gravel augmentation and habitat enhancement completed three years ago and a re-engineered, meandering channel and floodplain reach constructed over a decade ago. Spawning was observed at both sites in areas predicted to have high quality habitat, based on channel morphology and hydraulics. At the more recently restored gravel augmentation site, peak redd densities occurred in areas of high sediment mobility as determined by measurements of gravel pivot angles and a grain entrainment model. Redds were built in areas with high values of hydraulic conductivity and streambed hyporheic fluxes, which were located near the transition between pool-riffle bedforms in the re-engineered reach but spanned the entire length of the gravel-augmented reach. In situ measurements of streambed hydraulic conductivity indicated lower hyporheic fluxes at the re-engineered, meandering site due to the infiltration of fine sediment into the subsurface. Highly mobile and permeable gravels were heavily utilized for spawning in restored reaches amid an otherwise predominantly armored bed. However the potential long-term, ecological benefits provided by large-scale restoration projects will vary depending on the patterns of post-restoration flow, sediment supply and channel evolution.

  16. Channel dynamics and geomorphic resilience in an ephemeral Mediterranean river affected by gravel mining (United States)

    Calle, Mikel; Alho, Petteri; Benito, Gerardo


    Gravel mining has been a widespread activity in ephemeral rivers worldwide whose long-lasting hydrogeomorphological impacts preclude effective implementation of water and environmental policies. This paper presents a GIS-based method for temporal assessment of morphosedimentary changes in relation to in-channel gravel mining in a typical ephemeral Mediterranean stream, namely the Rambla de la Viuda (eastern Spain). The aims of this work were to identify morphosedimentary changes and responses to human activities and floods, quantify river degradations and analyze factors favoring fluvial recovery for further applications in other rivers. Aerial photographs and LiDAR topography data were studied to analyze geomorphic evolution over the past 70 years along a 7.5-km reach of an ephemeral gravel stream that has been mined intensively since the 1970s. To evaluate changes in the riverbed, we mapped comparable units applying morphological, hydraulic, and stability (based on vegetation density and elevation) criteria to 13 sets of aerial photographs taken from 1946 to 2012. A detailed spatiotemporal analysis of comparable units revealed a 50% reduction in the active section and a 20% increase in stable areas, compared to the conditions observed prior to gravel mining. Instream mining was first observed in 1976 aerial photograph covering already up to 50% of the 1956 riverbed area. River degradation since then was quantified by means of a LiDAR DTM and RTK-GPS measurements, which revealed a 3.5-m incision that had started simultaneously with gravel mining. Climate and land use changes were present but the effects were completely masked by changes produced by instream gravel mining. Therefore, river incision/degradation was triggered by scarcity of sediment and lack of longitudinal sedimentary connection, creating an unbalanced river system that is still adjusting to the present hydrosedimentary conditions.

  17. Development of an analytical method for distinguishing ammonium bicarbonate from the products of an aqueous ammonia CO2 scrubber. (United States)

    Meng, Lingyu; Burris, Stuart; Bui, Holt; Pan, Wei-Ping


    The link between anthropogenic emissions of carbon dioxide, increasing atmospheric CO2 levels, and concomitantly increasing global temperatures is established and accepted. The use of aqueous ammonia, to capture CO2 and produce an inexpensive nitrogen fertilizer, ammonium bicarbonate (ABC), is believed to be a feasible approach to CO2 sequestration. Due to the varying concentrations of reactants and varying reaction conditions, different ammonia-carbon compounds may be produced. ABC is the ideal product for maximizing NH3 utilization in CO2 capture; therefore, identification and quantification of ABC in the reaction products is mandatory. Various analytical techniques were used to distinguish and quantify the ABC. Fourier transform infrared spectroscopy can only be used to distinguish ammonium carbamate, and. X-ray diffraction can be used to qualitatively distinguish ABC from the other possible products of the CO2 capture reaction. Carbon-hydrogen-nitrogen elemental analysis and near-infrared (NIR) spectroscopy were used to quantify ABC, with both techniques giving +/-5% agreement for ABC concentrations for 8 of 13 samples from a bench-scale aqueous ammonia CO2 scrubbing system. An additional 3 of the 13 samples were within +/-12%. Results indicate that NIR will be an ideal tool for real-time, on-line measurements of ABC in a full-scale aqueous ammonia CO2 scrubber. The ABC in 11 samples from the bench-scale scrubber at Western Kentucky University was determined by these techniques and assessed to have very good quality as a fertilizer in accordance with GB-3559-92, the Agricultural Ammonium Bicarbonate National Standard of China.

  18. Groundwater and surface water interaction in flow-through gravel pit lakes. (United States)

    Nella Mollema, Pauline; Antonellini, Marco


    Gravel pits are excavated in aquifers to fulfill the need for construction materials. Flow-through lakes form when the gravel pits are below the water table and fill with groundwater. In certain areas there are more than 60 of these lakes close together and their presence changes the drainage patterns and water- and hydrochemical budgets of a watershed. In flow-through gravel pit lakes, groundwater mixes with surface water and interacts with the atmosphere; outflow occurs only via groundwater. The lifespan of gravel pit lakes may be up to thousands of years as their depth to surface ratio is typically large and sedimentation rates are low. We have studied two gravel pit lake systems, a fluvial freshwater system in the Netherlands and a coastal brackish lake system in Italy. One Dutch gravel pit lake studied in detail is in part artificially replenished with Meuse River water for drinking water production that occurs downstream of the lake by water pumps. The Italian gravel pit lakes are fed by brackish groundwater that is a mix of freshwater from precipitation, Apennine Rivers and brackish (Holocene) Adriatic Sea water. Here, the drainage system of the low lying land enhances groundwater flow into the lake. Surface water evaporation is larger in temperate and Mediterranean climates than the actual evapotranspiration of pre-existing grassland and forests. The lakes, therefore, cause a loss of freshwater. The creation of water surfaces allows algae and other flora and fauna to develop. In general, water becomes gradually enriched in certain chemical constituents on its way through the hydrological cycle, especially as groundwater due to water-rock interactions. When groundwater ex-filtrates into gravel pit lakes, the natural flow of solutes towards the sea is interrupted. Hydrochemical analysis of ground- and surface waters, as well as chemical analysis of lake bottom sediments and stable H and O isotope data, show that gravel pit lake water is characterized (among

  19. Fly ash stabilisation of gravel roads; Flygaska som foerstaerkningslager i grusvaeg

    Energy Technology Data Exchange (ETDEWEB)

    Macsik, Josef


    Majority of the existing gravel roads have low bearing capacity during spring and autumn, due to thaw and/or rain. Low bearing capacity leads often to bad road conditions. This situation results in higher costs for the lumber industry and the public. Management of gravel roads all the year around would traditionally require excavation of frost susceptible soils and replacement with natural materials. Fly ash (from bio fuels) has good technical properties as bearing layer in road constructions. Fly ash stabilised gravel roads have better function and longer life span with less maintenance than traditional gravel roads. The aim of this project is to show how fly ash stabilisation of gravel roads can increase bearing capacity and what its environmental impact is. The overall aim is to make it easier for entrepreneurs and consulting companies to use fly ash during gravel road renovation and/or constructing new gravel roads. This report targets fly ash producers and road constructors as well as environmental agencies. Two different pilot tests were investigated in this study, Norberg with fly ash from Stora Enso Fors AB, and Boerje (Uppsala) with fly ash from Vattenfall Uppsala AB. Both road sections with related reference section were investigated during a two year period. Only fly ash was used in the bearing layer at Norberg and fly ash gravel was used at Boerje. Bearing capacity was investigated twice, for both locations, November 2003 one month after the road renovation and during thawing, April 2004. Water samples from lysimeters, ground water and surface water were only collected and analysed from Norberg. Experience from the fly ash stabilised road sections show that curing and traffic load can with time compensate for less compaction. The same is noticed at Boerje, although deflection measurements show that there are small differences. Stabilisation of gravel roads increases the roads bearing capacity. Two years after stabilisation 90 timber loads were

  20. Impact of gravel mining on benthic invertebrate communities in a highly dynamic gravel-bed river: an integrated methodology to link geomorphic disturbances and ecological status (United States)

    Béjar, María; Gibbins, Chris; Vericat, Damià; Batalla, Ramon J.; Buendia, Cristina; Lobera, Gemma


    Water and sediments are transported along river channels. Their supply, transport and deposition control river morphology and sedimentary characteristics, which in turn support habitat. Floods disturb river channels naturally although anthropogenic impacts may also contribute. River channel disturbance is considered the main factor affecting the organization of riverine communities and contributes to key ecological processes. In this paper we present an integrated methodology designed to analyze the impacts of in-channel gravel mining on benthic invertebrate communities. The study is conducted in the Upper River Cinca (Southern Pyrenees). A 11 km river reach is being monitored in order to understand the effects of floods and gravel mining on channel morphodynamics and invertebrate communities. The study reach is located in and upland gravel-bed system historically and currently affected by periodical episodes of in-channel sediment mining. This methodology has been developed in the background of the research project MorphSed. An integrated methodology of four components (Co) has been designed and is being implemented: (Co1) acquisition of high resolution imagery to generate topographic models before and after channel disturbances. Floods and in-channel gravel mining are considered natural and anthropogenic disturbances, respectively. Topographic models are obtained by means of combining automated digital photogrammetry (SfM) and optical bathymetric models. Event-scale models are used to assess the spatial extent and magnitude of bed disturbance. (Co2) Invertebrate sampling in 5 representative reaches along the study site. Invertebrate surber samples are providing data to define assemblages and their characteristics (composition, density, distribution, traits). These data is used to assess the spatial extent of channel disturbance impacts on the taxonomic and trait structure of communities. (Co3) Monitoring flow and sediment transport in the upstream and downstream

  1. Resistivity Profiling for Mapping Gravel Layers That May Control Contaminant Migration at the Amargosa Desert Research Site, Nevada (United States)

    Lucius, Jeffrey E.; Abraham, Jared D.; Burton, Bethany L.


    Gaseous contaminants, including CFC 113, chloroform, and tritiated compounds, move preferentially in unsaturated subsurface gravel layers away from disposal trenches at a closed low-level radioactive waste-disposal facility in the Amargosa Desert about 17 kilometers south of Beatty, Nevada. Two distinct gravel layers are involved in contaminant transport: a thin, shallow layer between about 0.5 and 2.2 meters below the surface and a layer of variable thickness between about 15 and 30 meters below land surface. From 2003 to 2005, the U.S. Geological Survey used multielectrode DC and AC resistivity surveys to map these gravel layers. Previous core sampling indicates the fine-grained sediments generally have higher water content than the gravel layers or the sediments near the surface. The relatively higher electrical resistivity of the dry gravel layers, compared to that of the surrounding finer sediments, makes the gravel readily mappable using electrical resistivity profiling. The upper gravel layer is not easily distinguished from the very dry, fine-grained deposits at the surface. Two-dimensional resistivity models, however, clearly identify the resistive lower gravel layer, which is continuous near the facility except to the southeast. Multielectrode resistivity surveys provide a practical noninvasive method to image hydrogeologic features in the arid environment of the Amargosa Desert.

  2. A laboratory experiment on the evolution of a sand gravel reach under a lack of sediment supply

    NARCIS (Netherlands)

    Orru, C.; Chavarrias Borras, V.; Ferrara, V.; Stecca, G.; Blom, A.


    A flume experiment was conducted to examine the evolution of a sand-gravel reach under a lack of sediment supply. A bed composed of a bimodal sediment mixture was installed with a uniform slope and an gradual fining pattern. At the upstream end of the flume the initial bed consisted of 100% gravel,

  3. Applying the seedling-emergence method under waterlogged conditions to detect the seed bank of aquatic plants in submerged sediments

    NARCIS (Netherlands)

    Boedeltje, G; ter Heerdt, GNJ; Bakker, JP

    Seed bank studies focused on submerged aquatic plants are generally performed under submerged conditions, using the seedling-emergence method. However, if a study targets at both submerged species and helophytes, submerged conditions are generally not suitable. We tested the emergence of seedlings

  4. Response of Vegetation on Gravel Bars to Management Measures and Floods: Case Study From the Czech Republic

    Directory of Open Access Journals (Sweden)

    Eremiášová Renata


    Full Text Available This article investigates response of vegetation on gravel bars to management measures and floods. The management measures consisted of the partial removal of gravel and vegetation cover, and were applied to six gravel bars on the Ostravice River, Czech Republic. Unexpected floods occu-rred in 2010, with the amplitude of 5- to 50-year repetition. Research of vegetation on the gravel bars consisted of vegetation survey before the management works; the monitoring of vegetation development over the following year and the verification of the relationships of species diversity, successional stages and the biotope conditions with the help of multivariate analysis (detrended correspondence analysis. Vegetation on the gravel bars was at different successional stages, and had higher diversity and vegetation cover before the management measures and floods. The mul-tivariate analysis revealed a shift toward initial successional stages with high demand on moisture, temperature and light after both management measures and floods.

  5. Unifying criterion for the velocity reversal hypothesis in gravel-bed rivers (United States)

    Diego Caamano; Peter Goodwin; John M. Buffington; Jim C. P. Liou; Stanley Daley-Laursen


    It has been hypothesized that velocity reversals provide a mechanism for maintaining pool-riffle morphology in gravel-bed rivers-an important habitat for salmonids, which are at risk in many places worldwide and that are the focus of extensive environmental legislation in Europe and North America. However, the occurrence of velocity reversals has been controversial for...

  6. 75 FR 68606 - Chetco River Gravel Mining Executive and Technical Teams; Notification of Availability of Documents. (United States)


    ...; Notification of Availability of Documents. AGENCY: U.S. Army Corps of Engineers, DoD. ACTION: Notice. SUMMARY..., meeting minutes, reports, and other documents related to the proposed Chetco River Gravel Mining Regional... documents. The Corps will consider these comments in the evaluation of whether to issue the Chetco River...

  7. Sediment transport primer: estimating bed-material transport in gravel-bed rivers (United States)

    Peter Wilcock; John Pitlick; Yantao Cui


    This primer accompanies the release of BAGS, software developed to calculate sediment transport rate in gravel-bed rivers. BAGS and other programs facilitate calculation and can reduce some errors, but cannot ensure that calculations are accurate or relevant. This primer was written to help the software user define relevant and tractable problems, select appropriate...

  8. Coupling fine particle and bedload transport in gravel-bedded streams (United States)

    Park, Jungsu; Hunt, James R.


    Fine particles in the silt- and clay-size range are important determinants of surface water quality. Since fine particle loading rates are not unique functions of stream discharge this limits the utility of the available models for water quality assessment. Data from 38 minimally developed watersheds within the United States Geological Survey stream gauging network in California, USA reveal three lines of evidence that fine particle release is coupled with bedload transport. First, there is a transition in fine particle loading rate as a function of discharge for gravel-bedded sediments that does not appear when the sediment bed is composed of sand, cobbles, boulders, or bedrock. Second, the discharge at the transition in the loading rate is correlated with the initiation of gravel mobilization. Third, high frequency particle concentration and discharge data are dominated by clockwise hysteresis where rising limb discharges generally have higher concentrations than falling limb discharges. These three observations across multiple watersheds lead to a conceptual model that fine particles accumulate within the sediment bed at discharges less than the transition and then the gravel bed fluidizes with fine particle release at discharges above the transition discharge. While these observations were individually recognized in the literature, this analysis provides a consistent conceptual model based on the coupling of fine particle dynamics with filtration at low discharges and gravel bed fluidization at higher discharges.

  9. Frost susceptibility of sub-base gravel used in Pearl-Chain Bridges: an experimental investigation

    DEFF Research Database (Denmark)

    Lund, Mia Schou Møller; Hansen, Kurt Kielsgaard; Andersen, Iben Brøndum


    This study investigates frost susceptibility of sub-base gravel determined by the ASTM D5918-13 standard as a conservative estimate of the frost heave risk of fill in overfilled arch bridges, particularly in Pearl-Chain Bridges. Frost heave of granular materials has been of great research interes...

  10. The relationship between emergence from spawning gravel and growth in farmed rainbow trout Oncorhynchus mykiss

    DEFF Research Database (Denmark)

    Åberg Andersson, Madelene; Laursen, Danielle Caroline; SILVA, P.I.M.


    The relationship between the timing of emergence from spawning gravel and growth after emergence was investigated in farmed Oncorhynchus mykiss. A relationship between the time of emergence and growth became evident after 6 months of rearing, where individuals with an intermediate emergence time ...

  11. Experimental study on piping in sandy gravel foundations considering effect of overlying clay

    Directory of Open Access Journals (Sweden)

    Shuang Wang


    Full Text Available The influence of the overlying clay on the progression of piping in the sandy gravel foundation of water-retaining structures is often neglected. In order to study this influence, an experimental investigation was conducted on a laboratory-scale model. It was discovered that the critical hydraulic gradient and the area of the piping tunnel increase when the overlying clay thickens. With a thicker clay layer, erosion of the sandy gravel below the clay layer occurs later, but, once the erosion starts, the erosion rate is very high and the average velocity of water seeping through the cross-section of the sandy gravel increases rapidly due to the low deformability of the thick clay layer. Furthermore, it was found that the progression of piping is a complicated and iterative process involving erosion of fine particles, clogging of pores, and flushing of the clogged pores. Two types of erosion have been identified in the progression of piping: one causes the tunnel to advance upstream, and the other increases the depth of the tunnel. The results show that the overlying clay is an important factor when evaluating piping in sandy gravel foundations of water-retaining structures.

  12. The effect of coarse gravel on cohesive sediment entrapment in an annular flume

    Directory of Open Access Journals (Sweden)

    K. Glasbergen


    Full Text Available While cohesive sediment generally represents a small fraction (16 Pa, cohesive materials trapped within the gravel bed will be entrained and transported into the Glenmore Reservoir, where sediment-associated nutrients may pose treatment challenges to the drinking water supply.

  13. Turbulence measurements over immobile gravel with additions of sand from supply limited to capacity transport conditions (United States)

    Measurement of the turbulence that drives sand transport over and through immobile gravels is relevant to efforts to model sediment movement downstream of dams, where fine sediments are eroded from coarse substrates and are not replaced due to the presence of the upstream dam. The relative elevatio...

  14. Frost susceptibility of sub-base gravel used in Pearl-Chain Bridges: an experimental investigation

    DEFF Research Database (Denmark)

    Lund, Mia Schou Møller; Hansen, Kurt Kielsgaard; Andersen, Iben Brøndum


    This study investigates frost susceptibility of sub-base gravel determined by the ASTM D5918-13 standard as a conservative estimate of the frost heave risk of fill in overfilled arch bridges, particularly in Pearl-Chain Bridges. Frost heave of granular materials has been of great research interest...

  15. Industrial applications of the air direct-contact, gravel, ground heat exchanger (United States)

    Cepiński, Wojciech; Besler, Maciej


    The paper describes the analysis of possibility of using the air direct-contact, gravel, ground heat exchanger (Polish acronym BGWCiM), patented at the Wroclaw University of Science and Technology to prepare air for conditioning rooms in the industry. Indicated the industry sectors where the application may be the most beneficial.

  16. Low-cost multi-stage filtration enhanced by coagulation-flocculation in upflow gravel filtration

    NARCIS (Netherlands)

    Sanchez, L.D.; Marin, L.M.; Visscher, J.T.; Rietveld, L.C.


    This paper assesses the operational and design aspects of coagulation and flocculation in upflow gravel filters (CF-UGF) in a multi-stage filtration (MSF) plant. This study shows that CF-UGF units improve the performance of MSF considerably, when the system operates with turbidity above 30 NTU. It

  17. Labour-based bitumen roads as cost-effective alternatives to conventional gravel wearing courses

    CSIR Research Space (South Africa)

    Paige-Green, P


    Full Text Available . As part of the Gundo Lashu Programme for Labour Intensive Rural Roads Maintenance that is currently being implemented in Limpopo Province, the training of 24 emerging contractors in rehabilitation of rural gravel roads was carried out. These emerging...

  18. Ecological significance of riverine gravel bars in regulated river reaches below dams (United States)

    Ock, G.; Takemon, Y.; Sumi, T.; Kondolf, G. M.


    A gravel bar has been recognized as ecologically significant in that they provide simplified habitat with topographical, hydrological and thermo-chemical diversity, while enhancing material exchanges as interfaces laterally between aquatic and terrestrial habitats, and vertically between surface and subsurface waters. During past several decades, regulated rivers below dams have been loss of a number of the geomorphological features due to sediment starvation by upstream dams, accompanied by a subsequent degradation of their ecological functions. Despite a growing concern for gravel bar management recognizing its importance in recovering riverine ecosystem services, the ecological roles of gravel bars have not been assessed enough from the empirical perspectives of habitat diversity and organic matter interactions. In this study, we investigate the 'natural filtering effects' for reducing lentic plankton and contaminants associated with self-purification, and 'physicochemical habitat complexity' of gravel bars, focusing on reach-scaled gravel bars in rivers located in three different countries; First is the Uji River in central Japan, where there has been a loss of gravel bars in the downstream reaches since an upstream dam was constructed in 1965; second is the Tagliamento River in northeast Italy, which shows morphologically intact braided bar channels by natural flooding events and sediment supply; third is the Trinity River in the United States (located in northern California), the site of ongoing restoration efforts for creating new gravel bars through gravel augmentation and channel rehabilitation activities. We traced the downstream changes in particulate organic matter (POM) trophic sources (composed of allochthonous terrestrial inputs, autochthonous instream production and lentic plankton from dam outflows) in order to evaluate the roles of the geomorphological features in tailwater ecosystem food-resources shifting. We calculated suspended POM

  19. Run-of-River Impoundments Can Remain Unfilled While Transporting Gravel Bedload: Numerical Modeling Results (United States)

    Pearson, A.; Pizzuto, J. E.


    Previous work at run-of-river (ROR) dams in northern Delaware has shown that bedload supplied to ROR impoundments can be transported over the dam when impoundments remain unfilled. Transport is facilitated by high levels of sand in the impoundment that lowers the critical shear stresses for particle entrainment, and an inversely sloping sediment ramp connecting the impoundment bed (where the water depth is typically equal to the dam height) with the top of the dam (Pearson and Pizzuto, in press). We demonstrate with one-dimensional bed material transport modeling that bed material can move through impoundments and that equilibrium transport (i.e., a balance between supply to and export from the impoundment, with a constant bed elevation) is possible even when the bed elevation is below the top of the dam. Based on our field work and previous HEC-RAS modeling, we assess bed material transport capacity at the base of the sediment ramp (and ignore detailed processes carrying sediment up and ramp and over the dam). The hydraulics at the base of the ramp are computed using a weir equation, providing estimates of water depth, velocity, and friction, based on the discharge and sediment grain size distribution of the impoundment. Bedload transport rates are computed using the Wilcock-Crowe equation, and changes in the impoundment's bed elevation are determined by sediment continuity. Our results indicate that impoundments pass the gravel supplied from upstream with deep pools when gravel supply rate is low, gravel grain sizes are relatively small, sand supply is high, and discharge is high. Conversely, impoundments will tend to fill their pools when gravel supply rate is high, gravel grain sizes are relatively large, sand supply is low, and discharge is low. The rate of bedload supplied to an impoundment is the primary control on how fast equilibrium transport is reached, with discharge having almost no influence on the timing of equilibrium.

  20. Outer region scaling using the freestream velocity for nonuniform open channel flow over gravel (United States)

    Stewart, Robert L.; Fox, James F.


    The theoretical basis for outer region scaling using the freestream velocity for nonuniform open channel flows over gravel is derived and tested for the first time. Owing to the gradual expansion of the flow within the nonuniform case presented, it is hypothesized that the flow can be defined as an equilibrium turbulent boundary layer using the asymptotic invariance principle. The hypothesis is supported using similarity analysis to derive a solution, followed by further testing with experimental datasets. For the latter, 38 newly collected experimental velocity profiles across three nonuniform flows over gravel in a hydraulic flume are tested as are 43 velocity profiles previously published in seven peer-reviewed journal papers that focused on fluid mechanics of nonuniform open channel over gravel. The findings support the nonuniform flows as equilibrium defined by the asymptotic invariance principle, which is reflective of the consistency of the turbulent structure's form and function within the expanding flow. However, roughness impacts the flow structure when comparing across the published experimental datasets. As a secondary objective, we show how previously published mixed scales can be used to assist with freestream velocity scaling of the velocity deficit and thus empirically account for the roughness effects that extend into the outer region of the flow. One broader finding of this study is providing the theoretical context to relax the use of the elusive friction velocity when scaling nonuniform flows in gravel bed rivers; and instead to apply the freestream velocity. A second broader finding highlighted by our results is that scaling of nonuniform flow in gravel bed rivers is still not fully resolved theoretically since mixed scaling relies to some degree on empiricism. As researchers resolve the form and function of macroturbulence in the outer region, we hope to see the closing of this research gap.

  1. Methods for geothermal reservoir detection emphasizing submerged environments

    Energy Technology Data Exchange (ETDEWEB)

    Case, C.W.; Wilde, P.


    This report has been prepared for the California State Lands Commission to aid them in evaluating exploration programs for geothermal reservoirs, particularly in submerged land environments. Three charts show: (1) a logical progression of specific geologic, geochemical, and geophysical exploration techniques for detecting geothermal reservoirs in various geologic environments with emphasis on submerged lands, (2) various exploration techniques which can be used to develop specific information in geothermal areas, and (3) if various techniques will apply to geothermal exploration according to a detailed geologic classification. A narrative in semi-outline form supplements these charts, providing for each technique; a brief description, advantages, disadvantages, special geologic considerations, and specific references. The specific geologic situation will control the exploration criterion to be used for reservoir detection. General guidelines are established which may be of use in evaluating such a program, but the optimum approach will vary with each situation.

  2. Antitumor activity of submerged biomass of Hericium erinaceus


    Avtonomova, A.; Bakanov, A.; Vinokurov, V.; Bukhman, V.; Krasnopolskaya, L.


    Submerged cultivation of Hericium erinaceus in various media has been studied. The yield of biomass was shown to depend mainly on the carbon source, whereas the content of watersoluble polysaccharides depended primarily on the nitrogen source. Using optimal medium composition, the biomass yield of 22-23 g/l in 7 days was achieved. The antitumor activity was studied in vivo with using 2 tumor strains. The inhibition ratio of tumor in these experience reached 86%. An exposure of mice with tumor...

  3. Submerged Pagodas of Mahabalipuram - Study based on underwater investigations

    Digital Repository Service at National Institute of Oceanography (India)

    Sundaresh; Gaur, A.S.; Tripati, S.; Vora, K.H.; Rao, K.M.

    - gested that this place could have served as an ancient port (Dayalan, 1992). Mahabalipuram was well known to earlier mariners as 'Seven Pagodas' since the 1 7h century AD. it is generally believed that out of 7 temples originally con- structed, all... based on the local traditions and available literature. The local tradition and the people of Mahabalipuram believe that five temples similar to the Shore Temple have been submerged in the sea. On the basis of local traditions Ancient Tamil...

  4. Instrumentation, control, and automation for submerged anaerobic membrane bioreactors


    Robles Martínez, Ángel; Durán Pinzón, Freddy; Ruano García, María Victoria; Ribes Bertomeu, José; Rosado Muñoz, Alfredo; SECO TORRECILLAS, AURORA; Ferrer, J.


    A submerged anaerobic membrane bioreactor (AnMBR) demonstration plant with two commercial hollow-fibre ultrafiltration systems (PURON® , Koch Membrane Systems, PUR-PSH31) was designed and operated for urban wastewater treatment. An instrumentation, control, and automation (ICA) system was designed and implemented for proper process performance. Several single-input-single-output (SISO) feedback control loops based on conventional on off and PID algorithms were implemented to control the follo...

  5. On the submerging of a spherical intruder into granular beds (United States)

    Wu, Chuan-Yu; Zhang, Ling; Chen, Lan


    Granular materials are complex systems and their mechanical behaviours are determined by the material properties of individual particles, the interaction between particles and the surrounding media, which are still incompletely understood. Using an advanced discrete element method (DEM), we simulate the submerging process of a spherical projectile (an intruder) into granular materials of various properties with a zero penetration velocity (i.e. the intruder is touching the top surface of the granular bed and released from stationary) and examine its settling behaviour. By systematically changing the density and size of the intruder and the particle density (i.e. the density of the particles in the granular bed), we find that the intruder can sink deep into the granular bed even with a zero penetration velocity. Furthermore, we confirm that under certain conditions the granular bed can behave like a Newtonian liquid and the submerging intruder can reach a constant velocity, i.e. the terminal velocity, identical to the settling of a sphere in a liquid, as observed experimentally. A mathematical model is also developed to predict the maximum penetration depth of the intruder. The model predictions are compared with experimental data reported in the literature,good agreement was obtained, demonstrating the model can accurately predict the submerging behaviour of the intruder in the granular media.

  6. Research efforts for detection and recovery of submerged oil

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, K. [United States Coast Guard, Groton, CT (United States). Research and Development Center


    Submerged oil can sink and destroy shellfish and other marine populations in addition to causing closure of water intakes at industrial facilities and power plants. However, current methods to find and recover oil from spills involving submerged oil are inadequate. The underwater environment presents major challenges such as poor visibility, difficulty in tracking oil spill movement, colder temperatures, inadequate containment methods and problems with the equipment's interaction with water. This paper reported on a multi-year project launched by the Research and Development Center of the United States Coast Guard to develop a complete approach for spills of submerged oil. The project involved detection technologies and recovery methods for oil on the bottom of any body of water. Proof of concept (POC) and prototype tests of potential detection technologies were evaluated during tests at the Ohmsett facility in Leonardo, New Jersey. The technologies included sonar, laser fluorometry, real-time mass spectrometry and in-situ fluorometry. This paper described the development of a complete specification for an integrated recovery system along with a plan for future development. 9 refs., 2 tabs., 11 figs.

  7. Measurement of Submerged Oil/Gas Leaks using ROV Video (United States)

    Shaffer, Franklin; de Vera, Giorgio; Lee, Kenneth; Savas, Ömer


    Drilling for oil or gas in the Gulf of Mexico is increasing rapidly at depths up to three miles. The National Commission on the Deepwater Horizon Oil Leak concluded that inaccurate estimates of the leak rate from the Deepwater Horizon caused an inadequate response and attempts to cap the leak to fail. The first response to a submerged oil/gas leak will be to send a Remotely Operated Vehicle (ROV) down to view the leak. During the response to the Deepwater Horizon crisis, the authors Savas and Shaffer were members of the Flow Rate Technical Group's Plume Team who used ROV video to develop the FRTG's first official estimates of the oil leak rate. Savas and Shaffer developed an approach using the larger, faster jet features (e.g., turbulent eddies, vortices, entrained particles) in the near-field developing zone to measure discharge rates. The authors have since used the Berkeley Tow Tank to test this approach on submerged dye-colored water jets and compressed air jets. Image Correlation Velocimetry has been applied to measure the velocity of visible features. Results from tests in the Berkeley Tow Tank and submerged oil jets in the OHMSETT facility will be presented.

  8. Production of Alpha Amylase by Bacillus cereus in Submerged Fermentation

    Directory of Open Access Journals (Sweden)

    Helen H. Raplong


    Full Text Available Microorganisms have the ability to secrete enzymes when they are grown in the presence of certain substrates. Amylases are among the most important industrial enzymes and are of great significance in biotechnological studies. Bacteria belonging to the genus Bacillus were isolated using mannitol egg yolk polymyxin B (MYP agar a highly selective media for Bacillus cereus isolation. The isolates were tested for α-amylase production on nutrient agar supplemented with starch and in submerged fermentation. The bacteria isolated and identified (using the Microgen Bacillus identification kit were all Bacillus cereus and SB2 had the largest zone of hydrolysis of 12mm on nutrient agar supplemented with starch as well as the highest enzyme activity of 1.62U/ml. Amylase activity of 2.56U/ml was obtained after 24 hours incubation in submerged fermentation. When amylase enzyme production parameters where optimized, maximum amylase activity was obtained at a pH of 6.5, temperature of 350C, incubation time of 24 hours and 4% inoculums concentration. Bacillus cereus SB2 is a potential isolate for alpha-amylase production with soluble starch as the sole carbon source in submerged fermentation.

  9. On the submerging of a spherical intruder into granular beds

    Directory of Open Access Journals (Sweden)

    Wu Chuan-Yu


    Full Text Available Granular materials are complex systems and their mechanical behaviours are determined by the material properties of individual particles, the interaction between particles and the surrounding media, which are still incompletely understood. Using an advanced discrete element method (DEM, we simulate the submerging process of a spherical projectile (an intruder into granular materials of various properties with a zero penetration velocity (i.e. the intruder is touching the top surface of the granular bed and released from stationary and examine its settling behaviour. By systematically changing the density and size of the intruder and the particle density (i.e. the density of the particles in the granular bed, we find that the intruder can sink deep into the granular bed even with a zero penetration velocity. Furthermore, we confirm that under certain conditions the granular bed can behave like a Newtonian liquid and the submerging intruder can reach a constant velocity, i.e. the terminal velocity, identical to the settling of a sphere in a liquid, as observed experimentally. A mathematical model is also developed to predict the maximum penetration depth of the intruder. The model predictions are compared with experimental data reported in the literature,good agreement was obtained, demonstrating the model can accurately predict the submerging behaviour of the intruder in the granular media.

  10. Evaluation of the NH3 Removal Efficiency of an Acid Packed Bed Scrubber Using Two Methods: A Case Study in a Pig Facility


    Estellés, F.; Melse, R.W.; Ogink, N. W. M.; Calvet Sanz, Salvador


    [EN] The use of air cleaning systems to reduce ammonia emissions from animal houses is increasing. These systems are normally used in order to comply with local or national regulations of ammonia emission. Therefore, accurate determination of the proportion of ammonia being removed by these systems is crucial. There are two main methods available to measure ammonia removal efficiency of scrubbers: air balance (based on the measurement of ammonia concentrations in air) and combined water-air b...

  11. Intensification of volatile organic compounds mass transfer in a compact scrubber using the O3/H2O2 advanced oxidation process: kinetic study and hydroxyl radical tracking. (United States)

    Biard, Pierre-François; Couvert, Annabelle; Renner, Christophe; Levasseur, Jean-Pierre


    This study assesses the potential of ozonation and advanced oxidation process O(3)/H(2)O(2) to enhance the dimethyldisulfide (DMDS) mass transfer in a compact chemical scrubber developed for air treatment applications. Theoretical calculations, through Hatta number and enhancement factor evaluations for two parallel irreversible reactions, were compared to experimental data and enabled the description of the mass transfer mechanisms. These calculations required the determination of the kinetic constant of the DMDS oxidation by molecular ozone ( [Formula: see text] ) and the measurement of the hydroxyl radical concentration within the scrubber. The competitive kinetic method using the 1,2-dihydroxybenzene (resorcinol) enabled to determine a value of the kinetic constant [Formula: see text] of 1.1×10(6)M(-1)s(-1) at 293K. Then, experiments using para-chlorobenzoic acid in solution allowed measuring the average hydroxyl concentration in the scrubber between the inlet and the outlet depending on the chemical conditions (pH and inlet O(3) and H(2)O(2) concentrations). High hydroxyl radical concentrations (10(-8)M) and ratio of the HO°-to-O(3) exposure (R(ct)≈10(-4)) were put in evidence. Copyright © 2011 Elsevier Ltd. All rights reserved.

  12. Antioxidant Properties of the Edible Basidiomycete Armillaria mellea in Submerged Cultures


    Lung, Ming-Yeou; Chang, Yu-Cheng


    Antioxidant components, ascorbic acid, total flavonoids and total phenols are produced effectively by Armillaria mellea submerged cultures. Dried mycelia and mycelia-free broths obtained by A. mellea submerged cultures are extracted with methanol and hot water and investigated for antioxidant properties. Methanolic extracts from dried mycelia (MEM) and mycelia-free broth (MEB) and hot water extracts from dried mycelia (HWEM) by A. mellea submerged cultures show good antioxidant properties as ...

  13. Enhanced effects of biotic interactions on predicting multispecies spatial distribution of submerged macrophytes after eutrophication


    Song, Kun; Cui, Yichong; Zhang, Xijin; Pan, Yingji; Xu, Junli; Xu, Kaiqin; Da, Liangjun


    Abstract Water eutrophication creates unfavorable environmental conditions for submerged macrophytes. In these situations, biotic interactions may be particularly important for explaining and predicting the submerged macrophytes occurrence. Here, we evaluate the roles of biotic interactions in predicting spatial occurrence of submerged macrophytes in 1959 and 2009 for Dianshan Lake in eastern China, which became eutrophic since the 1980s. For the four common species occurred in 1959 and 2009,...

  14. Geological peculiarities of the Pleistocene gravel and conglomerate deposits in the Upper Carniola, NW Slovenia

    Directory of Open Access Journals (Sweden)

    Ljubo Žlebnik


    Full Text Available An old interglacial Sava river bed with cliff walls up to 40 m deep into the old Pleistocene conglomerate deposist was exposed by excavation of two big gravel pits in the Sora field and in the valley of Naklo in Upper Camiola. The canyon was cut during the last interglacial period and again refilled with gravel in the lastglacial period. Conglomerate walls of the canyon were well polished by large quantities of rapidly moving material originating from nearby situated terminal moraines still partly preserved close to the present-day town of Radovljica.This curious geological occurrence discovered by human activity deserves to be protected as an interesting evidence of natural forces in the past.

  15. GigaUnit Transplant System: A New Mechanical Tool for Transplanting Submerged Aquatic Vegetation

    National Research Council Canada - National Science Library

    Shafer, Deborah J


    Submerged aquatic vegetation (SAV) performs many important ecosystem functions, including wave attenuation and sediment stabilization, water quality improvement, primary production, food web support for secondary consumers...

  16. Surface particle sizes on armoured gravel streambeds: Effects of supply and hydraulics (United States)

    Peter J. Whiting; John G. King


    Most gravel-bed streams exhibit a surface armour in which the median grain size of the surface particles is coarser than that of the subsurface particles. This armour has been interpreted to result when the supply of sediment is less than the ability of the stream to move sediment. While there may be certain sizes in the bed for which the supply is less than the...

  17. Barrier erosion control test plan: Gravel mulch, vegetation, and soil water interactions

    Energy Technology Data Exchange (ETDEWEB)

    Waugh, W.J.; Link, S.O. (Pacific Northwest Lab., Richland, WA (USA))


    Soil erosion could reduce the water storage capacity of barriers that have been proposed for the disposal of near-surface waste at the US Department of Energy's Hanford Site. Gravel mixed into the top soil surface may create a self-healing veneer that greatly retards soil loss. However, gravel admixtures may also enhance infiltration of rainwater, suppress plant growth and water extraction, and lead to the leaching of underlying waste. This report describes plans for two experiments that were designed to test hypotheses concerning the interactive effects of surface gravel admixtures, revegetation, and enhanced precipitation on soil water balance and plant abundance. The first experiment is a factorial field plot set up on the site selected as a soil borrow area for the eventual construction of barriers. The treatments, arranged in a a split-split-plot design structure, include two densities of gravel admix, a mixture of native and introduced grasses, and irrigation to simulate a wetter climate. Changes in soil water storage and plant cover are monitored with neutron moisture probes and point intercept sampling, respectively. The second experiment consists of an array of 80 lysimeters containing several different barrier prototypes. Surface treatments are similar to the field-plot experiment. Drainage is collected from a valve at the base of each lysimeter tube, and evapotranspiration is estimated by subtraction. The lysimeters are also designed to be coupled to a whole-plant gas exchange system that will be used to conduct controlled experiments on evapotranspiration for modeling purposes. 56 refs., 6 figs., 8 tabs.

  18. Cement Type Influence on Alkali-Silica Reaction in Concrete with Crushed Gravel Aggregate (United States)

    Rutkauskas, A.; Nagrockienė, D.; Skripkiūnas, G.


    Alkali-silica reaction is one of the chemical reactions which have a significant influence for durability of concrete. During alkali and silica reaction, silicon located in aggregates of the concrete, reacts with high alkali content. This way in the micropores of concrete is forming hygroscopic gel, which at wet environment, expanding and slowly but strongly destroying concrete structures. The goal of this paper- to determine the influence of cement type on alkali-silica reaction of mortars with crushed gravel. In the study crushed gravel with fraction 4/16 mm was used and four types of cements tested: CEM I 42.5 R; CEM I 42.5 SR; CEM II/A-S 42.5; CEM II/A-V 52.5. This study showed that crushed gravel is low contaminated on reactive particles containing of amorphous silica dioxide. The expansion after 14 days exceed 0.054 %, by RILEM AAR-2 research methodology (testing specimen dimension 40×40×160 mm). Continuing the investigation to 56 days for all specimens occurred alkaline corrosion features: microcracking and the surface plaque of gel. The results showed that the best resistance to alkaline corrosion after 14 days was obtained with cement CEM I 42.5 SR containing ash additive, and after 56 days with cement CEM II/A-V 52.5 containing low alkali content. The highest expansion after 14 and 56 days was obtained with cement CEM I 42.5 R without active mineral additives.

  19. Evaluation of Hydraulic Parameters Obtained by Different Measurement Methods for Heterogeneous Gravel Soil

    Directory of Open Access Journals (Sweden)

    Chen Zeng


    Full Text Available Knowledge of soil hydraulic parameters for the van Genuchten function is important to characterize soil water movement for watershed management. Accurate and rapid prediction of soil water flow in heterogeneous gravel soil has become a hot topic in recent years. However, it is difficult to precisely estimate hydraulic parameters in a heterogeneous soil with rock fragments. In this study, the HYDRUS-2D numerical model was used to evaluate hydraulic parameters for heterogeneous gravel soil that was irregularly embedded with rock fragments in a grape production base. The centrifugal method (CM, tensiometer method (TM and inverse solution method (ISM were compared for various parameters in the van Genuchten function. The soil core method (SCM, disc infiltration method (DIM and inverse solution method (ISM were also investigated for measuring saturated hydraulic conductivity. Simulation with the DIM approach revealed a problem of overestimating soil water infiltration whereas simulation with the SCM approach revealed a problem of underestimating water movement as compared to actual field observation. The ISM approach produced the best simulation result even though this approach slightly overestimated soil moisture by ignoring the impact of rock fragments. This study provides useful information on the overall evaluation of soil hydraulic parameters attained with different measurement methods for simulating soil water movement and distribution in heterogeneous gravel soil.

  20. Greywater treatment by granular filtration system using volcanic tuff and gravel media. (United States)

    Albalawneh, Abeer; Chang, Tsun-Kuo; Alshawabkeh, Heba


    The main objective of this study was to evaluate the efficiency of a granular filtration system (GFS) in greywater treatment under arid and semi-arid conditions. Six GFSs were designed, constructed, and monitored for approximately 13 months. Each GFS served a single rural Jordanian home by treating their greywater. Volcanic tuff media were used as the filtration media in three of the GFSs while the remaining three GFSs used gravel media. Results show that the biological oxygen demand, chemical oxygen demand, and total suspended solids of the effluent were significantly lower as compared to the influent and demonstrated a removal efficiency of 73%, 65%, and 85%, respectively, when using volcanic tuff media. The removal efficiency was 49%, 51%, and 76%, respectively, when using gravel media. There was a significant increase in the electrical conductivity, pH, potassium (K+), magnesium (Mg2+), chloride (Cl-), sodium (Na+), sulfate (SO42-), bicarbonates (HCO3-), sodium adsorption ratio, and exchangeable sodium percentage in the effluents of the GFS that used volcanic tuff media. The study suggests that GFSs can adequately treat greywater under arid conditions. However, gravel media produce less concentrated effluent compared to the volcanic tuff media.

  1. Horicon National Wildlife Refuge, Green Bay N.W. Refuge, Gravel Island N.W. Refuge: Narrative report: 1972 (United States)

    US Fish and Wildlife Service, Department of the Interior — This annual narrative report for Horicon NWR, Green Bay NWR, and Gravel Island NWR outlines Refuge accomplishments during the 1972 calendar year. The report begins...

  2. Frost Resistance and Permeability of Cement Stabilized Gravel used as Filling Material for Pearl-Chain Bridges

    DEFF Research Database (Denmark)

    Lund, Mia Schou Møller; Hansen, Kurt Kielsgaard; Hertz, Kristian Dahl


    The Pearl-Chain Bridge Technology introduces a new innovative arch bridge solution which com-bines the statical advantages of an arch bridge with a minimum of traffic disturbance. The arch-shaped substructure is stabilized by a filling material, e.g. cement stabilized gravel, which should meet...... several requirements on its moisture properties. In this paper the frost resistance, the liquid water permeability and the water vapour permeability of cement stabilized gravel are examined for two different cement contents. It is found that a small increase in cement content from 4% to 5% increases...... the 28-days compressive strength from 6.2 MPa to 12.3 MPa. The frost resistance of cement stabilized gravel with 5% cement content is better than for cement stabilized gravel with 4% cement content. The liquid water permeability coefficient and the water vapour permeability coefficient are significantly...

  3. Restoring Ecological Function to a Submerged Salt Marsh (United States)

    Stagg, C.L.; Mendelssohn, I.A.


    Impacts of global climate change, such as sea level rise and severe drought, have altered the hydrology of coastal salt marshes resulting in submergence and subsequent degradation of ecosystem function. A potential method of rehabilitating these systems is the addition of sediment-slurries to increase marsh surface elevation, thus ameliorating effects of excessive inundation. Although this technique is growing in popularity, the restoration of ecological function after sediment addition has received little attention. To determine if sediment subsidized salt marshes are functionally equivalent to natural marshes, we examined above- and belowground primary production in replicated restored marshes receiving four levels of sediment addition (29-42 cm North American Vertical Datum of 1988 [NAVD 88]) and in degraded and natural ambient marshes (4-22 cm NAVD 88). Moderate intensities of sediment-slurry addition, resulting in elevations at the mid to high intertidal zone (29-36 cm NAVD 88), restored ecological function to degraded salt marshes. Sediment additions significantly decreased flood duration and frequency and increased bulk density, resulting in greater soil drainage and redox potential and significantly lower phytotoxic sulfide concentrations. However, ecological function in the restored salt marsh showed a sediment addition threshold that was characterized by a decline in primary productivity in areas of excessive sediment addition and high elevation (>36 cm NAVD 88). Hence, the addition of intermediate levels of sediment to submerging salt marshes increased marsh surface elevation, ameliorated impacts of prolonged inundation, and increased primary productivity. However, too much sediment resulted in diminished ecological function that was equivalent to the submerged or degraded system. ?? 2010 Society for Ecological Restoration International.

  4. Enhanced Sorbitol Production under Submerged Fermentation using Lactobacillus plantarum

    Directory of Open Access Journals (Sweden)

    Khan Nadiya Jan


    Full Text Available Background and Objective: Sorbitol is a non-toxic and slightly hygroscopic compound with different applications. Zymomonas mobiles produces sorbitol from sucrose or mixtures of glucose and fructose (formation is coupled with the dehydrogenation of glucose to glucono-δ- lactone. Recombinant Zymomonas mobilis may produce sorbitol and gluconic acid from glucose and fructose using different divalent metal ions with reduced the ethanol yield andsignificantly increased yield of sorbitol. Current study envisaged to alter the media components, physical process parameters and supplementation of amino acids for enhanced sorbitol production.Material and Methods: Several process variables were evaluated on sorbitol production including carbon sources (glucose, fructose, maltose, sucrose, carbon concentrations (5, 10, 20 and 25 g l-1, nitrogen sources (peptone, tryptone, yeast extract, beef extract and organic nitrogen mix, temperatures (25, 29, 33, 37, 41°C, pH (6, 6.5, 7 , 7.5 ,8, agitation rate (50, 100, 150, 200 rpm and amino acids (cysteine, cystine, tryptophanin batch cultivation ofLactobacillus plantarum NCIM 2912. Shake flask cultivation performed under optimum conditions like temperature 37°C, pH 7.0 and agitation rate of 150 rpm, resulted in enhanced sorbitol production. Comparative study of sorbitol production in solid state fermentation and submerged fermentation was also evaluated.Results and Conclusion: Batch cultivation under submerged conditions further performed in 7.5-l lab scale bioreactor (working volume 3.0-l under optimized conditions resulted in maximum cell biomass of 8.95±0.03 g g-1 and a sorbitol content of 9.78±0.04 g l-1 after 42.0 h of fermentation. Scale up study on bioreactor resulted in maximum sorbitol yield (Yp/x and productivity of 1.11 g g-1 and 0.50 g l-1 h under submerged fermentation, respectively.Conflict of interest: The authors declare no conflict of interest.

  5. [Genetic algorithm for fermentation kinetics of submerged fermentation by Morchella]. (United States)

    Wang, Ying; Piao, Meizi; Sun, Yonghai


    Fermentation kinetics is important for optimizing control and up-scaling fermentation process. We studied submerged fermentation kinetics of Morchella. Applying the genetic Algorithm in the Matlab software platform, we compared suitability of the Monod and Logistic models, both are commonly used in process of fungal growth, to describe Morchella growth kinetics. Meanwhile, we evaluated parameters involved in the models for Morchella growth, EPS production and substrate consumption. The results indicated that Logistic model fit better with the experimental data. The average error of this model was 5.8%. This kinetics model can be useful for optimizing and up-scaling fungal fermentation process.

  6. Liquid Film Diffusion on Reaction Rate in Submerged Biofilters

    DEFF Research Database (Denmark)

    Christiansen, Pia; Hollesen, Line; Harremoës, Poul


    Experiments were carried out in order to investigate the influence of liquid film diffusion on reaction rate in a submerged biofilter with denitrification and in order to compare with a theoretical study of the mass transfer coefficient. The experiments were carried out with varied flow, identified...... by the empty bed velocity of inflow and recirculation, respectively 1.3, 2.8, 5.6 and 10.9 m/h. The filter material consisted of 3 mm biostyren spheres. The results indicate that the influence of liquid film diffusion on reaction rate can be ignored....

  7. Slag Metal Reactions during Submerged Arc Welding of Alloy Steels (United States)

    Mitra, U.; Eagar, T. W.


    The transfer of Cr, Si, Mn, P, S, C, Ni, and Mo between the slag and the weld pool has been studied for submerged arc welds made with calcium silicate and manganese silicate fluxes. The results show a strong interaction between Cr and Si transfer but no interaction with Mn. The manganese silicate flux produces lower residual sulfur while the calcium silicate fluxes are more effective for removal of phosphorus. The effective oxygen reaction temperature lies between 1700 and 2000 °C for all elements studied. Evidence of Cr and Mn loss by metal vaporization is also presented.

  8. MANUAL. Fly ash in civil engineering, Gravel roads; HANDBOK. Flygaska i mark- och vaegbyggnad, Grusvaegar

    Energy Technology Data Exchange (ETDEWEB)

    Munde, Hanna; Svedberg, Bo; Macsik, Josef; Maijala, Aino; Lahtinen, Pentti; Ekdahl, Peter; Neren, Jens [Vattenfall AB, Stockholm (Sweden). Vaerme Norden


    Fly ash based on biofuels or coal has been used as construction material for a long time in roads and other civil engineering applications. Some example, where it has been used in roadbase and subbase of gravel roads, are in the counties of Uppsala, Soedermanland, Vaestmanland and in Finland. The use of fly ash has contributed to good function for example as bearing capacity, thaw and frost capacity and good durability. This has also reduced costs for maintenance. The objective of this project was to develop a manual to provide a base for contemporary use of fly ash in road constructions. In the manual experience from studies, field tests and regulations has been compiled. The manual handles fly ash as base for products to be used in base and subbase in gravel roads. Future user of the guidelines are mainly consultant engineers and contractors. However the aim of the manual is to also support road administrators, environmental authorities and industry. The project has been carried out parallel to another ongoing national project titled 'Guidelines, Use of alternative materials in civil engineering'. The objective of that project is to establish a base for handling of alternative materials in Sweden. Fly ash in gravel roads are mainly used in two typical applications, one without any additive in a single layer and one with fly ash mixed with gravel. The use of flyash provides functional properties such as increased stiffness, stability and enhanced frost and thaw capacity for the road construction in total. Furthermore the products based on fly ash will have low permeability and good frost and thaw durability. These properties are for example related to fly ash quality, design and construction and are in general expected to be better than for traditional constructions using, for example, sand or gravel. The properties can be enhanced further by using binders such as cement and Merit. Fly ash should always be used above the ground water table with

  9. Growth responses of selected freshwater algae to trace elements and scrubber ash slurry generated by coal-fired power plants

    Energy Technology Data Exchange (ETDEWEB)

    Vocke, R.W.


    The development and implementation of standard toxicity tests is a necessity if consistent and reliable data are to be obtained for water quality criteria. The adapted EPA AAPBT is an ideal static algal toxicity test system. The algal test medium has a chemical composition similar to natural unpolluted waters of low ionic strength. It is appropriate to use MATC water quality criteria when assessing the potential impact of pollutants generated by coal-fired power stations because these energy-generated pollutants typically enter aquatic systems in small quantities over long periods. The MATC water quality criteria are estimates of trace element and SASE levels, based on the most sensitive alga investigated, that will not cause significant changes in naturally-functioning algal populations. These levels are 0.016f mg L/sup -1/ As(V), 0.001 mg L/sup -1/ Cd(II), 0.004 mg L/sup -1/ Hg(II), 0.006 mg L/sup -1/ Se(VI), and 0.344% SASE. To provide viable working water quality criteria, an extrapolation from the laboratory to the natural environment must be made. Therefore, those oxidation states of the trace elements were selected which are the dominant states occurring in natural, unpolluted, slightly alkaline freshwaters. It must be pointed out that these MATC values are based on algal responses to single toxicants and no allowance is made for synergistic, additive, or antagonistic relationships which could occur in natural aquatic systems. Additionally, natural chelation may influence toxicity. The highly toxic nature of potential pollutants from coal-fired generating plants emphasizes the need for minimizing stack effluent pollutants and retaining scrubber ash slurry for proper disposal in an effort to maintain trace elements in concentration ranges compatible with naturally-functioning ecosystems.

  10. Cathodic disbonding of organic coatings on submerged steel

    Energy Technology Data Exchange (ETDEWEB)

    Knudsen, Ole oeystein


    In offshore oil production, submerged steel structures are commonly protected by an organic coating in combination with cathodic protection. The main advantage is that the coating decreases the current demand for cathodic protection. But the coating degrades with time. This thesis studies one of the most important mechanisms for coating degradation in seawater, cathodic disbonding. Seven commercial coatings and two model coatings with various pigmentations have been studied. Parameter studies, microscopy and studies of free films were used in the mechanism investigations. Exposure to simulated North Sea conditions was used in the performance studies. The effect of aluminium and glass barrier pigments on cathodic disbonding was investigated. The mechanism for the effect of the aluminium pigments on cathodic disbonding was also investigated. The transport of charge and oxygen to the steel/coating interface during cathodic disbonding was studied for two epoxy coatings. Cathodic disbonding, blistering and current demand for cathodic protection was measured for nine commercial coatings for submerged steel structures, using the ASTM-G8 standard test and a long term test under simulated North Sea conditions. The relevance of the ASTM-G8 test as a prequalification test was evaluated. 171 refs., 40 figs., 6 tabs.

  11. Period Doubling in Bubbling from a Submerged Nozzle (United States)

    Dennis, Jordan; Grace, Laura; Lehman, Susan

    The timing of bubbles rising from a nozzle submerged in a viscous solution was measured to examine the period-doubling route to chaos in this system. A narrow nozzle was submerged in a mixture of water and glycerin, and nitrogen was supplied to the nozzle at a varying flow rate. The bubbles were detected using a laser and photodiode system; when the bubbles rise through the laser beam, they scatter the light so that the signal at the photodiode decreases. The period between bubbles as well as the duration of each bubble (a function of bubble size and bubble velocity) was determined, and examined as the nitrogen flow rate increased, for solutions with five different concentrations of glycerin. Bubbles were also recorded visually using a high-speed camera. Within the flow rates tested, we observed a bifurcation of the period to period-2 behavior for all solutions tested, and a further bifurcation to period-4 for all solutions except pure glycerin. The solution viscosity affected both the onset of the bifurcation and the precise bubble behavior during the bifurcation. Unusually, a short period/long period pair of bubbles recurring at a regular interval was sometimes observed in the low flow regime which is typically period-1, an observation which requires further investigation. Research supported by NSF DMR 1560093.

  12. Magnetic imaging of a submerged Roman harbour, Caesarea Maritima, Israel (United States)

    Boyce, J. I.; Reinhardt, E. G.; Raban, A.; Pozza, M. R.


    The harbour built by King Herod's engineers at Caesarea represented a major advance in Roman harbour construction that incorporated the use of large (390 m^3), form-filled hydraulic concrete blocks to build an extensive foundation for the harbour moles and breakwater barriers. Marine geophysical surveys were recently conducted across the submerged harbour in an attempt to map the configuration of the buried concrete foundation. A total of 107 line km of high-resolution marine magnetic surveys (nominal 15 m line separations) and bathymetry data were acquired over a 1 km^2 area of the submerged harbour using an Overhauser marine magnetometer, integrated DGPS and single-beam (200 KHz) echosounder. The feasibility of magnetic detection of the concrete was established before the survey by magnetic susceptibility testing of concrete core samples. All concrete samples contained appreciable amounts of fe-oxide-rich volcanic ash ('pozzolana') and showed uniformly high susceptibility values (k > 10^-^4 cgs) when compared to harbour bottom sediments and building stones (k construction of the harbour moles and quays.


    Vermaire, Jesse C; Prairie, Yves T; Gregory-Eaves, Irene


    Submerged macrophytes are a central component of lake ecosystems; however, little is known regarding their long-term response to environmental change. We have examined the potential of diatoms as indicators of past macrophyte biomass. We first sampled periphyton to determine whether habitat was a predictor of diatom assemblage. We then sampled 41 lakes in Quebec, Canada, to evaluate whether whole-lake submerged macrophyte biomass (BiomEpiV) influenced surface sediment diatom assemblages. A multivariate regression tree (MRT) was used to construct a semiquantitative model to reconstruct past macrophyte biomass. We determined that periphytic diatom assemblages on macrophytes were significantly different from those on wood and rocks (ANOSIM R = 0.63, P macrophyte, nutrient-limited lakes (BiomEpiV ≥525 μg · L(-1) ; total phosphorus [TP] macrophyte, nutrient-limited lakes (BiomEpiV eutrophic lakes (TP ≥35 μg · L(-1) ; six lakes). A semiquantitative model correctly predicted the MRT group of the lake 71% of the time (P macrophytes have a significant influence on diatom community structure and that sedimentary diatom assemblages can be used to infer past macrophyte abundance. © 2011 Phycological Society of America.

  14. Wait or escape? Contrasting submergence tolerance strategies of Rorippa amphibia, Rorippa sylvestris and their hybrid

    NARCIS (Netherlands)

    Akman, M.; Bhikharie, A.V.; McLean, E.H.; Boonman, A.; Visser, E.J.W.; Schranz, M.E.; van Tienderen, P.H.


    Background and Aims Differential responses of closely related species to submergence can provide insight into the evolution and mechanisms of submergence tolerance. Several traits of two wetland species from habitats with contrasting flooding regimes, Rorippa amphibia and Rorippa sylvestris, as well

  15. Growth rate, protein:RNA ratio and stoichiometric homeostasis of submerged macrophytes under eutrophication stress


    Xing W.; Shi Q.; Liu H.; Liu G.


    Growth rate hypothesis (GRH) and stoichiometric homeostasis of photoautotrophs have always been questioned. However, little is known about GRH and stoichiometric homeostasis of aquatic plants, especially submerged macrophytes. Therefore, we aim to test the GRH and explore stoichiometric homeostasis of four freshwater submerged macrophytes under eutrophication stress. At the single species level and the multi-species level, N:P ratios ...

  16. Evidence of shoreline shift on the northern Saurashtra coast: Study based on the submerged temple complex at Pindara

    Digital Repository Service at National Institute of Oceanography (India)

    Gaur, A.S.; Sundaresh

    . It is difficult to assign a particular reason for the submergence of the temple in discussion, however minor sea level rise and seismic activity might have played a vital role in submergence of the temple complex....

  17. Submerged beach ridge lineation and associated sedentary fauna in the innershelf of Gopalpur Coast, Orissa, Bay of Bengal

    Digital Repository Service at National Institute of Oceanography (India)

    Rao, K.M.; Murthy, K.S.R.; Reddy, N.P.C.; Subrahmanyam, A.S.; Lakshminarayana, S.; Rao, M.M.M.; Sarma, K.V.L.N.S.; Premkumar, M.K.; Sree, A.; Bapuji, M.

    . (e - mail: RESEARCH COMMUNICATIONS CURRENT SCIENCE, VOL. 81, NO. 7, 10 OCTOBER 2001 829 mic profiling to locate the submerged roc k outcrops. Though the submerged topographic features were r e por - ted by some...

  18. EAARL-B Submerged Topography–Saint Croix, U.S. Virgin Islands, 2014 (United States)

    U.S. Geological Survey, Department of the Interior — A submerged topography Digital Elevation Model (DEM) mosaic for a portion of the submerged environs of Saint Croix, U.S. Virgin Islands, was produced from remotely...

  19. An evaluation of sand and gravel resources in and near the Prescott National Forest in the Verde Valley, Arizona; with a section on evaluation of sand and gravel resources using selected engineering variables (United States)

    Cox, Leslie J.; Bliss, James D.; Miller, Robert J.


    This study was based on available published literature. Although no field investigation was conducted in the Prescott National Forest to the west of the Verde River, a field investigation was conducted in the summer of 1994 by this author on the Coconino National Forest, to the east of the Verde River, where units of surficial materials of the same age and similar character are found (Cox, 1995). The intent of this evaluation of sand and gravel resources in the Prescott National Forest and adjacent areas in the Verde Valley, is to provide the land managers of the U.S. Forest Service with a map that delineates sand- and gravel-bearing geologic units. The map distinguishes (1) sand-and gravel-bearing units that are limited to channels from those that are not, (2) sand-and gravel-bearing units that are thin (generally less than 40 feet thick which is one contour interval on the topographic maps) from those that are locally thick (generally 40 feet or more), (3) sand- and gravel-bearing units that are poorly sorted from those that are well-sorted4, (4) sand- and gravel-bearing units that have little or no soil development from those that have greater degrees of soil development and lithification, (5) and sand- and gravel-bearing units that support riparian vegetation from those that do not. These distinctive characteristics are related to the geologic age or depositional setting of the rock materials and can be distinguished where areas are mapped in detail.


    Directory of Open Access Journals (Sweden)

    M. Mohd


    Full Text Available Concrete structures that exposed to marine environments are subjected to multiple deterioration mechanisms. An overview of the existing technology for submerged concrete, pressure resistant, concrete structures which related such as cracks, debonds, and delamination are discussed. Basic knowledge related to drowning durability such as submerged concrete structures in the maritime environment are the durability of a concrete and the ability to resist to weathering, chemical attack, abrasion or other deterioration processes. The measuring techniques and instrumentation for geometrical monitoring of submerged structural displacements have traditionally been categorized into two groups according to the two main groups, namely as geodetic surveying and geotechnical structural measurements of local displacements. This paper aims to study the durability of submerged concrete displacement and harmful effects of submerged concrete structures.

  1. [Effects of light on submerged macrophytes in eutrophic water: research progress]. (United States)

    Li-Sha, Zou; Ze-Yu, Nie; Xiao-Yan, Yao; Ji-Yan, Shi


    The restoration of submerged macrophytes is the key to remediate eutrophic water and maintain the health of aquatic ecosystem, while light is the main limiting factor. This paper summarized the factors affecting the light extinction in water and the mechanisms of light intensity affecting the physiology of submerged macrophytes, with the focuses on the metabolic mechanisms of carbon, nitrogen, and phosphorus, the responses of antioxidant enzyme system, and the feedbacks of pigment composition and concentration in the common submerged macrophytes under low light stress. Several engineering techniques applied in the ecological restoration of submerged macrophytes were presented, and the framework of the restoration of submerged macrophytes in eutrophic water was proposed. Some problems in current research and several suggestions on future research were addressed, which could help the related research and engineering practices.

  2. Treatment of heavy metals by iron oxide coated and natural gravel media in Sustainable urban Drainage Systems. (United States)

    Norris, M J; Pulford, I D; Haynes, H; Dorea, C C; Phoenix, V R


    Sustainable urban Drainage Systems (SuDS) filter drains are simple, low-cost systems utilized as a first defence to treat road runoff by employing biogeochemical processes to reduce pollutants. However, the mechanisms involved in pollution attenuation are poorly understood. This work aims to develop a better understanding of these mechanisms to facilitate improved SuDS design. Since heavy metals are a large fraction of pollution in road runoff, this study aimed to enhance heavy metal removal of filter drain gravel with an iron oxide mineral amendment to increase surface area for heavy metal scavenging. Experiments showed that amendment-coated and uncoated (control) gravel removed similar quantities of heavy metals. Moreover, when normalized to surface area, iron oxide coated gravels (IOCGs) showed poorer metal removal capacities than uncoated gravel. Inspection of the uncoated microgabbro gravel indicated that clay particulates on the surface (a natural product of weathering of this material) augmented heavy metal removal, generating metal sequestration capacities that were competitive compared with IOCGs. Furthermore, when the weathered surface was scrubbed and removed, metal removal capacities were reduced by 20%. When compared with other lithologies, adsorption of heavy metals by microgabbro was 10-70% higher, indicating that both the lithology of the gravel, and the presence of a weathered surface, considerably influence its ability to immobilize heavy metals. These results contradict previous assumptions which suggest that gravel lithology is not a significant factor in SuDS design. Based upon these results, weathered microgabbro is suggested to be an ideal lithology for use in SuDS.

  3. Leaf gas films contribute to rice (Oryza sativa) submergence tolerance during saline floods

    DEFF Research Database (Denmark)

    Herzog, Max; Konnerup, Dennis; Pedersen, Ole


    Floods and salinization of agricultural land adversely impact global rice production. We investigated whether gas films on leaves of submerged rice delay salt entry during saline submergence. Two-week-old plants with leaf gas films (+GF) or with gas films experimentally removed (-GF) were submerg...

  4. Edge Effects Are Important in Supporting Beetle Biodiversity in a Gravel-Bed River Floodplain (United States)

    Langhans, Simone D.; Tockner, Klement


    Understanding complex, dynamic, and diverse ecosystems is essential for developing sound management and conservation strategies. Gravel-bed river floodplains are composed of an interlinked mosaic of aquatic and terrestrial habitats hosting a diverse, specialized, and endangered fauna. Therefore, they serve as excellent models to investigate the biodiversity of multiple ecotones and related edge effects. In this study, we investigated the abundance, composition, richness, and conservation status of beetle assemblages at varying sediment depth (0, 0.1, 0.6 and 1.1 m), distance from the channel (1, 5, 20, and 60–100 m, and 5 m within the riparian forest), and time of the year (February–November) across a 200 m-wide gravel bar at the near-natural Tagliamento River (Italy), to detect edge effects in four floodplain ecotones: aquatic-terrestrial, forest-active floodplain, sediment-air, and sediment-groundwater. We used conventional pitfall traps and novel tube traps to sample beetles comparably on the sediment surface and within the unsaturated sediments. We found a total of 308 beetle species (including 87 of conservation concern) that showed multiple, significant positive edge effects across the floodplain ecotones, mainly driven by spatial heterogeneity: Total and red list beetle abundance and richness peaked on the sediment surface, at channel margins, and at the edge of the riparian forest. All ecotones possessed edge/habitat specialists. Most red list species occurred on the sediment surface, including five species previously considered extinct – yet two of these species occurred in higher densities in the unsaturated sediments. Conservation and management efforts along gravel-bed rivers must therefore promote a dynamic flow and sediment regime to create and maintain habitat heterogeneity and ecotone diversity, which support a unique and high biodiversity. PMID:25545280

  5. Can high resolution 3D topographic surveys provide reliable grain size estimates in gravel bed rivers? (United States)

    Pearson, E.; Smith, M. W.; Klaar, M. J.; Brown, L. E.


    High resolution topographic surveys such as those provided by Structure-from-Motion (SfM) contain a wealth of information that is not always exploited in the generation of Digital Elevation Models (DEMs). In particular, several authors have related sub-metre scale topographic variability (or 'surface roughness') to sediment grain size by deriving empirical relationships between the two. In fluvial applications, such relationships permit rapid analysis of the spatial distribution of grain size over entire river reaches, providing improved data to drive three-dimensional hydraulic models, allowing rapid geomorphic monitoring of sub-reach river restoration projects, and enabling more robust characterisation of riverbed habitats. However, comparison of previously published roughness-grain-size relationships shows substantial variability between field sites. Using a combination of over 300 laboratory and field-based SfM surveys, we demonstrate the influence of inherent survey error, irregularity of natural gravels, particle shape, grain packing structure, sorting, and form roughness on roughness-grain-size relationships. Roughness analysis from SfM datasets can accurately predict the diameter of smooth hemispheres, though natural, irregular gravels result in a higher roughness value for a given diameter and different grain shapes yield different relationships. A suite of empirical relationships is presented as a decision tree which improves predictions of grain size. By accounting for differences in patch facies, large improvements in D50 prediction are possible. SfM is capable of providing accurate grain size estimates, although further refinement is needed for poorly sorted gravel patches, for which c-axis percentiles are better predicted than b-axis percentiles.

  6. Applying biofilm analysis for detecting mobility or stability of gravel bed channel stretches (United States)

    Beylich, Achim A.; Gintz, Dorothea


    Within the project "Detects biofilm variability stable and mobile channel pavement patterns in steep bedload streams in cold environments?" (DAAD/NFR) studies on biofilm developed on mountain stream gravels have been performed. Field work was carried out in Nordfjord (Erdalen and Bødalen) in western Norway and at the Partnach River (Reintal) in the Bavarian Alps in Germany. The thickness and the volume of EPS (extracellular polymeric substances), algae and bacteria developed on selected sample stones, taken at different depths in channels and at different times, varied at the single stone itself and between the locations and in the timescale. A trend could be detected: The relation of EPS/bacteria and EPS/algae differed between subsurface samples (taken in 5 to 10 cm depth) and stones sampled at the surface. In most cases the total amount of biofilm EPS on the surface gravel was higher than on the subsurface samples. At a very stable channel stretch in Erdalen the EPS-volume and the amount of algae increased over time, but the bacterial content varied very high within the time frame. At a channel stretch with a positive sediment budget, as based on previous investigations, a clear trend to less biofilm in the subsurface material was observed. At a channel stretch with previously detected slow net-erosion the measured EPS-volume was on a high level as compared to other sampling sites. The development of algae and bacteria volume varied together widely over the time with no detected trend. The samples collected in the Partnach River (Reintal, Bavarian Alps) showed a clear pattern at all three sampling points, with the ratio of EPS and algae, and EPS / bacteria increasing with increasing depth in the subsurface. Biofilm analysis can be applied to analyse the stability / mobility of gravel bed channel stretches and to estimate the frequency and depth of sediment mobilisation within such channels.

  7. Enhanced removal of Exxon Valdez spilled oil from Alaskan gravel by a microbial surfactant. (United States)

    Harvey, S; Elashvili, I; Valdes, J J; Kamely, D; Chakrabarty, A M


    Remediation efforts for the oil spill from the Exxon Valdez tanker in Alaska have focused on the use of pressurized water at high temperature to remove oil from the beaches. We have tested a biological surfactant from Pseudomonas aeruginosa for its ability to remove oil from contaminated Alaskan gravel samples under various conditions, including concentration of the surfactant, time of contact, temperature of the wash, and presence or absence of xanthan gum. The results demonstrate the ability of the microbial surfactant to release oil to a significantly greater extent (2 to 3 times) than water alone, particularly at temperatures of 30 degrees C and above.

  8. Characterization of fluvial islands along three different gravel-bed rivers of North-Eastern Italy

    Directory of Open Access Journals (Sweden)

    L. Picco


    Full Text Available River islands are defined as discrete areas of woodland vegetation located in the riverbed and surrounded by either water-filled channels or exposed gravels, exhibiting some stability and remaining exposed during bank-full flows. Islands are very important from both morphological and ecological points of view, representing the most natural condition of a fluvial system and are strongly influenced by human impacts. This study aims at analyzing the morphological and vegetation characteristics of three different typologies of islands (pioneer, young and stable in three distinct rivers in the NE of Italy, affected by different intensities of human pressure. The study was conducted on several sub-reaches of the Piave, Brenta and Tagliamento rivers. The first is a gravel-bed river, which suffered intense and multiple human impacts, especially due to dam building and in-channel gravel mining. The same alterations can also be observed in the Brenta river, which also presents bank protections, hydropower schemes and water diversions. On the other hand, the Tagliamento river is a gravel-bed river characterized by a high level of naturality and very low human pressures. The analyses were conducted using aerial photographs and LiDAR data acquired in 2010 in order to define and distinguish the three different island typologies and to obtain a characterization of ground and vegetation features. The results suggest that the fluvial islands lie at different elevations and this fact implies a different resistance capacity during flood events. Pioneer islands and young islands lie at lower elevations than stable islands causing a lower capacity to survive during considerable flood events, in fact in most cases those islands typologies were removed by ordinary floods. Stable islands lie at higher elevations and only intense and infrequent flood events (RI > 10-15 years are able to determine considerable erosions. Regarding the characteristics of vegetation, we can

  9. Critical Assessment of Temperature Distribution in Submerged Arc Welding Process

    Directory of Open Access Journals (Sweden)

    Vineet Negi


    Full Text Available Temperature distribution during any welding process holds the key for understanding and predicting several important welding attributes like heat affected zone, microstructure of the weld, residual stress, and distortion during welding. The accuracy of the analytical approaches for modeling temperature distribution during welding has been constrained by oversimplified assumptions regarding boundary conditions and material properties. In this paper, an attempt has been made to model the temperature distribution during submerged arc welding process using finite element modeling technique implemented in ANSYS v12. In the present analysis, heat source is assumed to be double-ellipsoidal with Gaussian volumetric heat generation. Furthermore, variation of material properties with temperature and both convective and radiant heat loss boundary condition have been considered. The predicted temperature distribution is then validated against the experimental results obtained by thermal imaging of the welded plate, and they are found to be in a good agreement.

  10. Arc characteristics of submerged arc welding with stainless steel wire (United States)

    Li, Ke; Wu, Zhi-sheng; Liu, Cui-rong; Chen, Feng-hua


    The arc characteristics of submerged arc welding (SAW) with stainless steel wire were studied by using Analysator Hannover (AH). The tests were carried out under the same preset arc voltage combined with different welding currents. By comparing the probability density distribution (PDD) curves of arc voltage and welding current, the changes were analyzed, the metal transfer mode in SAW was deduced, and the characteristics of a stable arc were summarized. The analysis results show that, with an increase of welding parameters, the short-circuiting peak in the PDD curves of arc voltage decreases gradually until it disappears, and the dominant metal transfer mode changes from flux-wall guided transfer to projected transfer and then to streaming transfer. Moreover, when the PDD curves of arc voltage are both unimodal and generally symmetrical, the greater the peak probability and the smaller the peak span, the more stable the arc becomes.

  11. Numerical study on tsunami hazard mitigation using a submerged breakwater. (United States)

    Ha, Taemin; Yoo, Jeseon; Han, Sejong; Cho, Yong-Sik


    Most coastal structures have been built in surf zones to protect coastal areas. In general, the transformation of waves in the surf zone is quite complicated and numerous hazards to coastal communities may be associated with such phenomena. Therefore, the behavior of waves in the surf zone should be carefully analyzed and predicted. Furthermore, an accurate analysis of deformed waves around coastal structures is directly related to the construction of economically sound and safe coastal structures because wave height plays an important role in determining the weight and shape of a levee body or armoring material. In this study, a numerical model using a large eddy simulation is employed to predict the runup heights of nonlinear waves that passed a submerged structure in the surf zone. Reduced runup heights are also predicted, and their characteristics in terms of wave reflection, transmission, and dissipation coefficients are investigated.

  12. Numerical Study on Tsunami Hazard Mitigation Using a Submerged Breakwater

    Directory of Open Access Journals (Sweden)

    Taemin Ha


    Full Text Available Most coastal structures have been built in surf zones to protect coastal areas. In general, the transformation of waves in the surf zone is quite complicated and numerous hazards to coastal communities may be associated with such phenomena. Therefore, the behavior of waves in the surf zone should be carefully analyzed and predicted. Furthermore, an accurate analysis of deformed waves around coastal structures is directly related to the construction of economically sound and safe coastal structures because wave height plays an important role in determining the weight and shape of a levee body or armoring material. In this study, a numerical model using a large eddy simulation is employed to predict the runup heights of nonlinear waves that passed a submerged structure in the surf zone. Reduced runup heights are also predicted, and their characteristics in terms of wave reflection, transmission, and dissipation coefficients are investigated.

  13. Phytoremediation of arsenic in submerged soil by wetland plants. (United States)

    Jomjun, Nateewattana; Siripen, Trichaiyaporn; Maliwan, Saeouy; Jintapat, Nateewattana; Prasak, Thavornyutikarn; Somporn, Choonluchanon; Petch, Pengchai


    Wetland aquatic plants including Canna glauca L., Colocasia esculenta L. Schott, Cyperus papyrus L. and Typha angustifolia L. were used in the phytoremediation of submerged soil polluted by arsenic (As). Cyperus papyrus L. was noticed as the largest biomass producer which has arsenic accumulation capacity of 130-172 mg As/kg plant. In terms of arsenic removal rate, however, Colocasia esculenta L. was recognized as the largest and fastest arsenic remover in this study. Its arsenic removal rate was 68 mg As/m2/day while those rates of Canna glauca L., Cyperus papyrus L. and Typha angustifolia L. were 61 mg As/m2/day, 56 mg As/m2/day, and 56 mg As/m2/day, respectively. Although the 4 aquatic plants were inferior in arsenic accumulation, their high arsenic removal rates were observed. Phytostabilization should be probable for the application of these plants.

  14. Minimizing downstream scour due to submerged hydraulic jump using corrugated

    Directory of Open Access Journals (Sweden)

    Hossam Mohamed Ali


    Full Text Available Local scour downstream of hydraulic structures due to hydraulic jump is considered one of the tedious and complicated problems facing their stability. Throughout this paper, an experimental study was conducted to study the effect of using different spaced corrugated aprons on the downstream local scour due to submerged jump. Sixty runs were carried out in a horizontal rectangular flume to determine the optimal corrugation wavelength which minimizing the scour. A case of flat apron included to estimate the influence of corrugated aprons on scour holes dimensions. Two types of non-cohesive soil were used. Experiments were performed for a range of Froude numbers between 1.68 and 9.29. The results showed that using spaced triangular corrugated aprons minimize the scour depth and length of fine sand by average percentage of 63.4% and 30.2%, respectively and for coarse sand by 44.2% and 20.6% in comparing with classical jump.

  15. Microbial production of four biodegradable siderophores under submerged fermentation. (United States)

    Fazary, Ahmed E; Al-Shihri, Ayed S; Alfaifi, Mohammad Y; Saleh, Kamel A; Alshehri, Mohammed A; Elbehairi, Serag Eldin I; Ju, Yi-Hsu


    Four siderophore analogues were isolated and purified from Escherichia coli, Bacillus spp. ST13, and Streptomyces pilosus microorganisms under some specific submerged fermentation conditions. In order to evaluate the highest production of this siderophore analogues through the growth, a rapid spectrophotometric screening semi-quantitative method was used, in which interestingly the analogues were isolated in its own form not its iron chelate. After chromatographic separation, the chemical structures of the isolated and purified siderophores were illustrated using detailed spectroscopic techniques. The biodegradation studies were done on that four novel isolated and purified siderophores following OECD protocols. In addition, the bioactivities of these siderophores and their iron complexes were examined and evaluated. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. Development of Submerged Entry Nozzles that Resist Clogging

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Jeffrey D. Smith; Kent D. Peasle


    Accretion formation and the associated clogging of SENs is a major problem for the steel industry leading to decreased strand speed, premature changing of SENs or strand termination and the associated reductions in productivity, consistency, and steel quality. A program to evaluate potentially clog resistance materials was initiated at the University of Missouri-Rolla. The main objective of the research effort was to identify combinations of steelmaking and refractory practices that would yield improved accretion resistance for tundish nozzles and submerged entry nozzles. A number of tasks were identified during the initial kick-off meeting and each was completed with two exceptions, the thermal shock validation and the industrial trials. Not completing these two tasks related to not having access to industrial scale production facilities. Though much of the results and information generated in the project is of proprietary nature.

  17. Slag-metal equilibrium during submerged arc welding (United States)

    Chai, C. S.; Eagar, T. W.


    A thermodynamic model of the equilibria existing between the slag and the weld metal during submerged arc welding is presented. As formulated, the model applies only to fused neutral fluxes containing less than 20 pct CaF2, however some results indicate that the model may be useful in more general cases as well. The model is shown to be capable of predicting the gain or loss of both Mn and Si over a wide range of baseplate, electrode and flux compositions. At large deviations from the predicted equilibrium, the experimental results indicate considerable variability in the amount of Mn or Si transferred between the slag and metal phases, while closer to the calculated equilibrium, the extent of metal transfer becomes more predictable. The variability in metal transfer rate at large deviations from equilibrium may be explained by variations between the bulk and the surface concentrations of Mn and Si in both metal and slag phases.

  18. Endodontic Treatment in Submerged Roots: A Case Report

    Directory of Open Access Journals (Sweden)

    Hemalatha Pameshwar Hiremath


    Full Text Available Alveolar ridge resorption has long been considered an unavoidable consequence of tooth extraction. While the extent and pattern of resorption is variable among individuals, there is a progressive loss of ridge contour as a result of physiologic bone remodeling. Even today, with best modalities of tooth preservation, there is a group of elderly individuals who do not benefit from modern preventive practices and who now present a dilemma in terms of maintaining the masticatory apparatus necessary for nutrition. Even with excellent dental care, such patients experience abrasion of the natural tooth crowns with age, and embedded roots are left within the alveolar bone. According to old concepts of dental care, extraction of these roots would have been recommended, but today’s goal of excellence in endodontics dictates otherwise. We report a case in which vital and non-vital root submergence was carried out to prevent alveolar ridge reduction.

  19. Origin of well-rounded gravels in glacial deposits from Brøggerhalvøya, northwest Spitsbergen: potential problems caused by sediment reworking in the glacial environment


    Huddart, David; Bennett, Matthew R.; Hambrey, Michael J.; Glasser, Neil F.; Crawford, Kevin


    Well-rounded gravels are described from moraine-mound complexes, diamicton forefields and modern englacial thrusts at the margins of four glaciers on the northern side of Brøggerhalvøya, northwest Spitsbergen. Their shape charcteristics are compared with modern and fossil glacigenic, modern beach and Early Weichselian beach gravels from this peninsula. The best discriminators of the well-rounded gravels have been found to be the percentage-frequency roundness histograms, the roundness mid-poi...

  20. Soft Asphalt and Double Otta Seal—Self-Healing Sustainable Techniques for Low-Volume Gravel Road Rehabilitation

    Directory of Open Access Journals (Sweden)

    Audrius Vaitkus


    Full Text Available Increased traffic flow on low-volume gravel roads and deficiencies of national road infrastructure, are increasingly apparent in Lithuania. Gravel roads do not comply with requirements, resulting in low driving comfort, longer travelling time, faster vehicle amortization, and dustiness. The control of dustiness is one of the most important road maintenance activities on gravel roads. Another important issue is the assurance of required driving comfort and safety. Soft asphalt and Otta Seal technologies were proposed as a sustainable solution for the improvement of low-volume roads in Lithuania. Five gravel roads were constructed with soft asphalt, and 13 gravel roads were sealed with double Otta Seal, in 2012. The main aim of this research was to check soft asphalt and double Otta Seal’s ability to self-heal, on the basis of the results of the qualitative visual assessment of pavement defects and distress. The qualitative visual assessment was carried out twice a year following the opening of the rehabilitated road sections. The results confirmed soft asphalt and double Otta Seal’s ability to self-heal. The healing effect was more than 13% and 19% on roads with soft asphalt and double Otta Seal, respectively. In addition, on some roads, all cracks observed in spring self-healed during summer.

  1. Development of New Submergence Tolerant Rice Variety for Bangladesh Using Marker-Assisted Backcrossing

    Directory of Open Access Journals (Sweden)

    Khandakar Md Iftekharuddaula


    Full Text Available Submergence tolerant high yielding rice variety was developed using BR11 as a recipient parent applying foreground, phenotypic and background selection approaches. Recombinant selection was found essential to minimize linkage drag by BC2F2 generation. Without recombinant selection, the introgression size in the backcross recombinant lines (BRLs was approximately 15 Mb on the carrier chromosome. The BRLs were found submergence tolerance compared to the check varieties under complete submergence for two weeks at Bangladesh Rice Research Institute, and produced higher yield compared to the isogenic Sub1-line under controlled submerged condition. The BRL IR85260-66-654-Gaz2 was released as BRRI dhan52 in 2010, which was the first high yielding submergence tolerant variety in Bangladesh. BRRI dhan52 produced grain yield ranging from 4.2 to 5.2 t/hm2 under different flash flood prone areas of Bangladesh in three consecutive seasons. The study demonstrated the efficiency of recombinant selection and better adaptability of the newly released submergence tolerant high yielding variety in flash flood prone different areas of the country with respect to submergence tolerance and yield potential.

  2. Physiological and transcriptomic characterization of submergence and reoxygenation responses in soybean seedlings. (United States)

    Tamang, Bishal G; Magliozzi, Joseph O; Maroof, M A Saghai; Fukao, Takeshi


    Complete inundation at the early seedling stage is a common environmental constraint for soybean production throughout the world. As floodwaters subside, submerged seedlings are subsequently exposed to reoxygenation stress in the natural progression of a flood event. Here, we characterized the fundamental acclimation responses to submergence and reoxygenation in soybean at the seedling establishment stage. Approximately 90% of seedlings succumbed during 3 d of inundation under constant darkness, whereas 10 d of submergence were lethal to over 90% of seedlings under 12 h light/12 h dark cycles, indicating the significance of underwater photosynthesis in seedling survival. Submergence rapidly decreased the abundance of carbohydrate reserves and ATP in aerial tissue of seedlings although chlorophyll breakdown was not observed. The carbohydrate and ATP contents were recovered upon de-submergence, but sudden exposure to oxygen also induced lipid peroxidation, confirming that reoxygenation induced oxidative stress. Whole transcriptome analysis recognized genome-scale reconfiguration of gene expression that regulates various signalling and metabolic pathways under submergence and reoxygenation. Comparative analysis of differentially regulated genes in shoots and roots of soybean and other plants defines conserved, organ-specific and species-specific adjustments which enhance adaptability to submergence and reoxygenation through different metabolic pathways. © 2014 John Wiley & Sons Ltd.

  3. Submergence induced changes of molecular species in membrane lipids in Arabidopsis thaliana

    Directory of Open Access Journals (Sweden)

    Mulan Wang


    Full Text Available The composition of membrane lipids is sensitive to environmental stresses. Submergence is a type of stress often encountered by plants. However, how the molecular species of membrane lipids respond to submergence has not yet been characterised. In this study, we used a lipidomic approach to profile the molecular species of membrane lipids in whole plants of Arabidopsis thaliana that were completely submerged for three days. The plants survived one day of submergence, after which, we found that the total membrane lipids were only subtly decreased, showing significant decreases of monogalactosyldiacylglycerol (MGDG and phosphatidylcholine (PC and an increase of phosphatidic acid (PA; however, the basic lipid composition was retained. In contrast, three days of submergence caused plants to die, and the membranes deteriorated via the rapid loss of 96% of lipid content together with a 229% increase in PA. The turnover of molecular species from PG and MGDG to PA indicated that submergence-induced lipid changes occurred through PA-mediated degradation. In addition, molecular species of extraplastidic PG degraded sooner than plastidic ones, lyso-phospholipids exhibited various patterns of change, and the double-bond index (DBI remained unchanged until membrane deterioration. Our results revealed the unique changes of membrane lipids upon submergence and suggested that the major cause of the massive lipid degradation could be anoxia.

  4. The Performance and Fouling Control of Submerged Hollow Fiber (HF Systems: A Review

    Directory of Open Access Journals (Sweden)

    Ebrahim Akhondi


    Full Text Available The submerged membrane filtration concept is well-established for low-pressure microfiltration (MF and ultrafiltration (UF applications in the water industry, and has become a mainstream technology for surface-water treatment, pretreatment prior to reverse osmosis (RO, and membrane bioreactors (MBRs. Compared to submerged flat sheet (FS membranes, submerged hollow fiber (HF membranes are more common due to their advantages of higher packing density, the ability to induce movement by mechanisms such as bubbling, and the feasibility of backwashing. In view of the importance of submerged HF processes, this review aims to provide a comprehensive landscape of the current state-of-the-art systems, to serve as a guide for further improvements in submerged HF membranes and their applications. The topics covered include recent developments in submerged hollow fiber membrane systems, the challenges and developments in fouling-control methods, and treatment protocols for membrane permeability recovery. The highlighted research opportunities include optimizing the various means to manipulate the hydrodynamics for fouling mitigation, developing online monitoring devices, and extending the submerged HF concept beyond filtration.

  5. Sounds and vibrations in the frozen Beaufort Sea during gravel island construction. (United States)

    Greene, Charles R; Blackwell, Susanna B; McLennan, Miles Wm


    Underwater and airborne sounds and ice-borne vibrations were recorded from sea-ice near an artificial gravel island during its initial construction in the Beaufort Sea near Prudhoe Bay, Alaska. Such measurements are needed for characterizing the properties of island construction sounds to assess their possible impacts on wildlife. Recordings were made in February-May 2000 when BP Exploration (Alaska) began constructing Northstar Island about 5 km offshore, at 12 m depth. Activities recorded included ice augering, pumping sea water to flood the ice and build an ice road, a bulldozer plowing snow, a Ditchwitch cutting ice, trucks hauling gravel over an ice road to the island site, a backhoe trenching the sea bottom for a pipeline, and both vibratory and impact sheet pile driving. For all but one sound source (underwater measurements of pumping) the strongest one-third octave band was under 300 Hz. Vibratory and impact pile driving created the strongest sounds. Received levels of sound and vibration, as measured in the strongest one-third octave band for different construction activities, reached median background levels sounds, sounds, and <10 km away for in-ice vibrations.

  6. The possibility of using materials based on secondary gravel in civil construction

    Directory of Open Access Journals (Sweden)

    Galitskova Yulia


    Full Text Available By now, the wear and tear of housing stock is more than 50%. Each year the number of old and dilapidated housing is growing, but it is gradually replaced by modern buildings. However, wastes accumulated from dismantling of buildings and constructions, are underutilized and, usually are just stored at landfills, or used for temporary roads construction. The purpose of this research is to define construction wastes characteristics and to explore possibilities for recycling of wastes from construction materials production. The paper also analyzes housing stock condition and basic requirements to building materials used in construction; and demonstrates results building materials based on secondary gravel investigation. While working with materials based on waste requirements the authors conducted laboratory research. Thus, the paper presents the analysis of laboratory tests results that made it possible to draw conclusions about the possible use of building materials based on secondary gravel and about their conformity to specified requirements. The researchers also developed proposals and recommendations to improve the competitiveness of such materials.

  7. Experimental Analysis of Natural Gravel Covering as Cool Roofing and Cool Pavement

    Directory of Open Access Journals (Sweden)

    Anna Laura Pisello


    Full Text Available Passive solutions for building energy efficiency represent an interesting research focus nowadays. In particular, natural materials are widely investigated for their potential intrinsic high thermal energy and environmental performance. In this view, natural stones represent a promising solution as building envelope covering and urban pavement. This paper concerns the experimental characterization of several low-cost and local gravel coverings for roofs and urban paving, properly selected for their natural high albedo characteristics. To this aim, the in-field albedo of gravel samples is measured with varying grain size. These in-field measurements are compared to in-lab measurements of solar reflectance and thermal emissivity. The analysis shows a significant variation of the albedo with varying grain size. Both in-lab and in-field measurements agree that the stones with the finest grain size, i.e., fine sand, have the best optic-thermal performance in terms of solar reflectance (62%. This feature results in the reduction of the surface temperature when exposed to solar radiation. Moreover, a natural mixed stone is compared to the high reflectance stone, demonstrating that the chosen stone presents an intrinsic “cool” behavior. Therefore, this natural, low-cost, durable and sustainable material could be successfully considered as a natural cool roof or cool paving solution.

  8. Recycling municipal incinerator fly- and scrubber-ash into fused slag for the substantial replacement of cement in cement-mortars. (United States)

    Lee, Tzen-Chin; Rao, Ming-Kang


    Fly- and scrubber-ash (weight ratio of approximately 1:3) from municipal solid waste incinerators (MSWI) are a major land-fill disposal problem due to their leaching of heavy metals. We uniformly mixed both types of ash with optimal amounts of waste glass frit, which was then melted into a glassy slag. The glassy slag was then pulverized to a particle size smaller than 38microm for use as a cement substitute (20-40% of total cement) and blended with sand and cement to produce slag-blended cement-mortar (SCM) specimens. The toxicity characteristics of the leaching procedure tests on the pulverized slag samples revealed that the amount of leached heavy metals was far below regulatory thresholds. The compressive strength of the 28-day cured SCM specimens was comparable to that of ordinary Portland cement mortars, while the compressive strength of specimens cured for 60 or 90 days were 3-11% greater. The observed enhanced strength is achieved by Pozzolanic reaction. Preliminary evaluation shows that the combination of MSWI fly- and scrubber-ash with waste glass yields a cost effective and environmentally friendly cement replacement in cement-mortars.

  9. Performance evaluation of poly-urethane foam packed-bed chemical scrubber for the oxidative absorption of NH3 and H2S gases. (United States)

    Nisola, Grace M; Valdehuesa, Kris Niño G; Anonas, Alex V; Ramos, Kristine Rose M; Lee, Won-Keun; Chung, Wook-Jin


    The feasibility of open-pore polyurethane (PU) foam as packing material for wet chemical scrubber was tested for NH3 and H2S removals. The foam is inexpensive, light-weight, highly porous (low pressure drop) and provides large surface area per unit volume, which are desirable properties for enhanced gas/liquid mass transfer. Conventional HCl/HOCl (for NH3) and NaOH/NaOCl (for H2S) scrubbing solutions were used to absorb and oxidize the gases. Assessment of the wet chemical scrubbers reveals that pH and ORP levels are important to maintain the gas removal efficiencies >95%. A higher re-circulation rate of scrubbing solutions also proved to enhance the performance of the NH3 and H2S columns. Accumulation of salts was confirmed by the gradual increase in total dissolved solids and conductivity values of scrubbing solutions. The critical elimination capacities at >95% gas removals were found to be 5.24 g NH3-N/m3-h and 17.2 g H2S-S/m3-h at an empty bed gas residence time of 23.6 s. Negligible pressure drops (NH3 and H2S removals from high-volume dilute emissions.

  10. Oxygen absorption by adventitious roots promotes the survival of completely submerged terrestrial plants. (United States)

    Ayi, Qiaoli; Zeng, Bo; Liu, Jianhui; Li, Siqi; van Bodegom, Peter M; Cornelissen, Johannes H C


    Flooding imposes stress upon terrestrial plants because it results in oxygen deficiency, which is considered a major problem for submerged plants. A common response of terrestrial plants to flooding is the formation of aquatic adventitious roots. Some studies have shown that adventitious roots on submerged plants are capable of absorbing water and nutrients. However, there is no experimental evidence for the possible oxygen uptake function of adventitious roots or for how important this function might be for the survival of plants during prolonged submergence. This study aims to investigate whether adventitious roots absorb oxygen from the water column, and whether this new function is beneficial to the survival of completely submerged plants. TakingAlternanthera philoxeroides(Mart.) Griseb. as a representative species, the profiling of the underwater oxygen gradient towards living and dead adventitious roots on completely submerged plants was conducted, the oxygen concentration in stem nodes with and without adventitious roots was measured, and the growth, survival and non-structural carbohydrate content of completely submerged plants with and without adventitious roots was investigated. Oxygen profiles in the water column of adventitious roots showed that adventitious roots absorbed oxygen from water. It is found that the oxygen concentration in stem nodes having adventitious roots was higher than that in stem nodes without adventitious roots, which implies that the oxygen absorbed by adventitious roots from water was subsequently transported from the roots to other plant tissues. Compared with plants whose adventitious roots had been pruned, those with intact adventitious roots had slower leaf shedding, slower plant mass reduction, more efficient carbohydrate economy and prolonged survival when completely submerged. The adventitious roots ofA. philoxeroidesformed upon submergence can absorb oxygen from ambient water, thereby alleviating the adverse effects of

  11. Interaction of Submerged Breakwater by a Solitary Wave Using WC-SPH Method

    Directory of Open Access Journals (Sweden)

    Afshin Mansouri


    Full Text Available Interaction of a solitary wave and submerged breakwater is studied in a meshless, Lagrangian approach. For this purpose, a two-dimensional smoothed particle hydrodynamics (SPH code is developed. Furthermore, an extensive set of simulations is conducted. In the first step, the generated solitary wave is validated. Subsequently, the interaction of solitary wave and submerged breakwater is investigated thoroughly. Results of the interaction of solitary wave and a submerged breakwater are also shown to be in good agreement with published experimental studies. Afterwards, the effects of the inclination and length of breakwater as well as distance between two breakwaters are evaluated on damping ratio of breakwater.

  12. Oxygen dynamics during submergence in the halophytic stem succulent Halosarcia pergranulata

    DEFF Research Database (Denmark)

    Pedersen, Ole; Vos, Harrie; Colmer, Timothy David


    This study elucidated O2 dynamics in shoots and roots of submerged Halosarcia pergranulata (Salicornioideae), a perennial halophytic stem succulent that grows on flood-prone mudflats of salt lakes. Oxygen within shoots and roots was measured using microelectrodes, for plants when waterlogged...... the roots, at least during the first several hours (the time period measured) after submergence or when light periods followed darkness. The influence of light on tissue O2 dynamics was confirmed in an experiment on a submerged plant in a salt lake in south-western Australia. In the late afternoon, partial...

  13. Effects of submergence on growth and survival of saplings of three wetland trees differing in adaptive mechanisms for flood tolerance

    Directory of Open Access Journals (Sweden)

    Fumiko Iwanaga


    Full Text Available Aim of study: Withstanding total submergence and reaeration following submergence is essential for the survival and establishment of wetland species. We focused on “LOES–low oxygen escape syndrome” and “LOQS–low oxygen quiescence syndrome” and compared tolerances to total submergence among wetland woody species differing in morphological adaptation to soil flooding. Area of study, materials and methods: This study examined the survival of 2-year-old saplings of Taxodium distichum and Metasequioia glyptostroboides (LOQS species, and Alnus japonica (LOES species, during and after total submergence. Saplings were completely submerged, then de-submerged to determine trends in survival and growth Main results: The M. glyptostroboides and A. japonica saplings could not survive prolonged submergence for more than 8 weeks, whereas saplings of T. distichum survived for over 2 years. Submerged saplings of all species showed no significant growth or modifications in morphology and anatomy under water, such as shoot elongation, adventitious root formation, and/or aerenchyma development. All T. distichum saplings that were de-submerged in the second year had the same pattern of shoot growth regardless of differences in timing and seasonality of de-submergence. Wood formation in T. distichum saplings ceased during submergence and resumed after de-submergence in spring and summer, but not in autumn. Research highlights: T. distichum saplings, which survived longer submergence periods than A. japonica and M. glyptostroboides, had physiological characteristics, such as suspension of growth and metabolism, which allowed survival of protracted total submergence (at least 2 years when saplings were immersed during the dormant stage before leaf flushing.

  14. Outer Continental Shelf Submerged Lands Act Boundary - Atlantic Region NAD83 (United States)

    Bureau of Ocean Energy Management, Department of the Interior — This data set contains the Submerged Lands Act (SLA) boundary line (also known as State Seaward Boundary (SSB), or Fed State Boundary) in ESRI shapefile formats for...

  15. The Development of a Composite Consumable Insert for Submerged ARC Welding

    National Research Council Canada - National Science Library


    .... When the submerged arc process was utilized to weld the butt joint in large flat plate structures, the repositioning of the plate for welding of the reverse side was a costly time consuming procedure...

  16. Meta Modelling of Submerged-Arc Welding Design based on Fuzzy Algorithm (United States)

    Song, Chang-Yong; Park, Jonghwan; Goh, Dugab; Park, Woo-Chang; Lee, Chang-Ha; Kim, Mun Yong; Kang, Jinseo


    Fuzzy algorithm based meta-model is proposed for approximating submerged-arc weld design factors such as weld speed and weld output. Orthogonal array design based on the submerged-arc weld numerical analysis is applied to the proposed approach. The nonlinear finite element analysis is carried out to simulate the submerged-arc weld numerical analysis using thermo-mechanical and temperature-dependent material properties for general mild steel. The proposed meta-model based on fuzzy algorithm design is generated with triangle membership functions and fuzzy if-then rules using training data obtained from the Taguchi orthogonal array design data. The aim of proposed approach is to develop a fuzzy meta-model to effectively approximate the optimized submerged-arc weld factors. To validate the meta-model, the results obtained from the fuzzy meta-model are compared to the best cases from the Taguchi orthogonal array.

  17. Large-Scale Submerged Aquatic Vegetation Restoration in Chesapeake Bay: Status Report, 2003-2006

    National Research Council Canada - National Science Library

    Shafer, Deborah J; Bergstrom, Peter


    In 2003, the U.S. Army Engineer Research and Development Center (ERDC) and the National Oceanic and Atmospheric Administration Chesapeake Bay Office began a comprehensive research effort to restore submerged aquatic vegetation (SAV...

  18. Flow Velocity and Morphology of a Submerged Patch of the Aquatic Species

    NARCIS (Netherlands)

    Cornacchia, L.; Licci, S.; van de Koppel, J.; van der Wal, D.; Wharton, G.; Puijalon, S.; Bouma, T.J.


    The interaction between macrophytes and hydrodynamic conditions is animportant feature in many aquatic ecosystems. Submerged macrophytes can formmonospecific patches that interact with the flow and alter current velocity; withinthe same vegetation patch, plants are exposed to different levels of

  19. Uncalibrated EAARL-B Submerged Topography--Fort Lauderdale, Florida, 2014 (GEOID12A) (United States)

    U.S. Geological Survey, Department of the Interior — Binary point-cloud data of a portion of the submerged environs of Fort Lauderdale, Florida, were produced from remotely sensed, geographically referenced elevation...

  20. EAARL-B Submerged Topography - Saint Croix, U.S. Virgin Islands, 2014 (United States)

    U.S. Geological Survey, Department of the Interior — ASCII XYZ point cloud data for a portion of the submerged environs of Saint Croix, U.S. Virgin Islands, was produced from remotely sensed, geographically referenced...

  1. EAARL-B Submerged Topography—Crocker Reef, Florida, 2014 (United States)

    U.S. Geological Survey, Department of the Interior — ASCII XYZ point cloud data for a portion of the submerged environs of Crocker Reef, Florida, were produced from remotely sensed, geographically referenced elevation...

  2. Calibrated EAARL-B Submerged Topography--Fort Lauderdale, Florida, 2014 (GEOID12A) (United States)

    U.S. Geological Survey, Department of the Interior — Binary point-cloud data of a portion of the submerged environs of Fort Lauderdale, Florida, were produced from remotely sensed, geographically referenced elevation...

  3. Environmental Assessment: Submerged Aquatic Plant Management of Banks Lake, Banks Lake NWR, Lakeland, Georgia (United States)

    US Fish and Wildlife Service, Department of the Interior — This Environmental Assessment is an analysis of five alternatives developed to address themanagement of the submerged aquatic plants of Banks Lake on Banks Lake...

  4. Satellite remote sensing of submerged aquatic vegetation distribution and status in the Currituck Sound, NC. (United States)


    Submerged Aquatic Vegetation (SAV) is an important component in any estuarine ecosystem. As such, it is regulated by federal and state agencies as a jurisdictional resource, where impacts to SAV are compensated through mitigation. Historically, tradi...

  5. Root transcript profiling of two Rorippa (brassicaceae) species reveals gene clusters associated with extreme submergence tolerance.

    NARCIS (Netherlands)

    Sasidharan, R.; Mustroph, A.; Boonman, A.; Akman, M.; Ammerlaan, A.M.H.; Breit, T.M.; Schranz, M.E.; Voesenek, L.A.C.J.; Tienderen, van P.H.


    Complete submergence represses photosynthesis and aerobic respiration, causing rapid mortality in most terrestrial plants. However, some plants have evolved traits allowing them to survive prolonged flooding, such as species of the genus Rorippa, close relatives of Arabidopsis (Arabidopsis

  6. Root transcript profiling of two Rorippa species reveals gene clusters associated with extreme submergence tolerance

    NARCIS (Netherlands)

    Sasidharan, R.; Mustroph, A.; Boonman, A.; Akman, M.; Ammerlaan, A.M.H.; Breit, T.M.; Schranz, M.E.; Voesenek, L.A.C.J.; van Tienderen, P.H.


    Complete submergence represses photosynthesis and aerobic respiration, causing rapid mortality in most terrestrial plants. However, some plants have evolved traits allowing them to survive prolonged flooding, such as species of the genus Rorippa, close relatives of Arabidopsis (Arabidopsis

  7. Swan foraging shapes spatial distribution of two submerged plants, favouring the preferred prey species

    NARCIS (Netherlands)

    Sandsten, H.; Klaassen, M.R.J.


    Compared to terrestrial environments, grazing intensity on belowground plant parts may be particularly strong in aquatic environments, which may have great effects on plant-community structure. We observed that the submerged macrophyte, Potamogeton pectinatus, which mainly reproduces with tubers,

  8. EAARL-B Submerged Topography—Saint Thomas, U.S. Virgin Islands, 2014 (United States)

    U.S. Geological Survey, Department of the Interior — ASCII XYZ point cloud data for a portion of the submerged environs of Saint Thomas, U.S. Virgin Islands, was produced from remotely sensed, geographically referenced...

  9. Uncalibrated EAARL-B Submerged Topography--Fort Lauderdale, Florida, 2014 (WGS84) (United States)

    U.S. Geological Survey, Department of the Interior — Binary point-cloud data of a portion of the submerged environs of Fort Lauderdale, Florida, were produced from remotely sensed, geographically referenced elevation...

  10. Calibrated EAARL-B Submerged Topography--Fort Lauderdale, Florida, 2014 (WGS84) (United States)

    U.S. Geological Survey, Department of the Interior — Binary point-cloud data of a portion of the submerged environs of Fort Lauderdale, Florida, were produced from remotely sensed, geographically referenced elevation...

  11. Outer Continental Shelf Submerged Lands Act Boundary - Pacific Region - West Coast NAD83 (United States)

    Bureau of Ocean Energy Management, Department of the Interior — This data set contains the Submerged Lands Act (SLA)boundary line (also known as the State Seaward Boundary (SSB) and Fed State Boundary) for the BOEM Pacific Region...

  12. Process Modeling and Optimization of a Submerged Arc Furnace for Phosphorus Production

    NARCIS (Netherlands)

    Scheepers, E.; Yang, Y.; Adema, A.T.; Boom, R.; Reuter, M.A.


    This article presents a process model of a phosphorus-producing, submerged arc furnace. The model successfully incorporates accurate, multifield thermodynamic, kinetic, and industrial data with computational flow dynamic calculations and thus further unifies the sciences of kinetics and equilibrium

  13. EAARL-B Submerged Topography - Saint Croix and Saint Thomas, U.S. Virgin Islands, 2014 (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Binary point-cloud data for part of the submerged environs of Saint Croix and Saint Thomas, U.S. Virgin Islands, were produced from remotely sensed, geographically...

  14. Outer Continental Shelf Submerged Lands Act Boundary - Alaska Region NAD83 (United States)

    Bureau of Ocean Energy Management, Department of the Interior — This data set contains the Submerged Lands Act (SLA) boundary (also known as State Seaward Boundary (SSB), or Fed State Boundary) in ESRI shapefile format for the...

  15. Tolerance of combined submergence and salinity in the halophytic stem-succulent Tecticornia pergranulata

    DEFF Research Database (Denmark)

    Colmer, T D; Vos, H; Pedersen, Ole


    in waters of high salinity. A 'quiescence response', i.e. no shoot growth, would conserve carbohydrates, but tissue sugars still declined with time. A low K(+) : Na(+) ratio, typical for tissues of succulent halophytes, was tolerated even during prolonged submergence, as evidenced by maintenance......BACKGROUND AND AIMS: Habitats occupied by many halophytes are not only saline, but are also prone to flooding. Few studies have evaluated submergence tolerance in halophytes. METHODS: Responses to submergence, at a range of salinity levels, were studied for the halophytic stem-succulent Tecticornia...... pergranulata subsp. pergranulata (syn. Halosarcia pergranulata subsp. pergranulata). Growth and total sugars in succulent stems were assessed as a function of time after submergence. Underwater net photosynthesis, dark respiration, total sugars, glycinebetaine, Na(+), Cl(-) and K(+), in succulent stems, were...

  16. Dynamic Response Analysis of Cable of Submerged Floating Tunnel under Hydrodynamic Force and Earthquake

    Directory of Open Access Journals (Sweden)

    Zhiwen Wu


    Full Text Available A simplified analysis model of cable for submerged floating tunnel subjected to parametrically excited vibrations in the ocean environment is proposed in this investigation. The equation of motion of the cable is obtained by a mathematical method utilizing the Euler beam theory and the Galerkin method. The hydrodynamic force induced by earthquake excitations is formulated to simulate real seaquake conditions. The random earthquake excitation in the time domain is formulated by the stochastic phase spectrum method. An analytical model for analyzing the cable for submerged floating tunnel subjected to combined hydrodynamic forces and earthquake excitations is then developed. The sensitivity of key parameters including the hydrodynamic, earthquake, and structural parameters on the dynamic response of the cable is investigated and discussed. The present model enables a preliminary examination of the hydrodynamic and seismic behavior of cable for submerged floating tunnel and can provide valuable recommendations for use in design and operation of anchor systems for submerged floating tunnel.

  17. EAARL-B submerged topography: Barnegat Bay, New Jersey, pre-Hurricane Sandy, 2012 (United States)

    Wright, C. Wayne; Troche, Rodolfo J.; Klipp, Emily S.; Kranenburg, Christine J.; Fredericks, Alexandra M.; Nagle, David B.


    These remotely sensed, geographically referenced elevation measurements of lidar-derived submerged topography datasets were produced by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, Florida.

  18. Metal accumulation by submerged macrophytes in eutrophic lakes at the watershed scale. (United States)

    Xing, Wei; Wu, Haoping; Hao, Beibei; Liu, Guihua


    Metal concentrations (Al, Ba, Ca, K, Li, Mg, Na, Se, Sr and Ti) in submerged macrophytes and corresponding water and sediments were studied in 24 eutrophic lakes along the middle and lower reaches of the Yangtze River (China). Results showed that these eutrophic lakes have high metal concentrations in both water and sediments because of human activities. Average concentrations of Al and Na in tissues of submerged macrophytes were very high in sampled eutrophic lakes. By comparison, Ceratophyllum demersum and Najas marina accumulated more metals (e.g. Ba, Ca, K, Mg, Na, Sr and Ti). Strong positive correlations were found between metal concentrations in tissues of submerged macrophytes, probably because of co-accumulation of metals. The concentrations of Li, Mg, Na and Sr in tissues of submerged macrophytes significantly correlated with their corresponding water values, but not sediment values.

  19. Outer Continental Shelf Submerged Lands Act Boundary - Gulf of Mexico Region NAD27 (United States)

    Bureau of Ocean Energy Management, Department of the Interior — This data set contains the Submerged Lands Act (SLA) boundary line (also known as State Seaward Boundary (SSB), or Fed State Boundary)in ESRI shapefile formats for...

  20. Suitability of seagrasses and submerged aquatic vegetation as indicators of eutrophication (United States)

    Rooted submerged aquatic vegetation (SAV) encompasses a large diversity of species that range from obligate halophytes such as, seagrasses, to euryhaline species and freshwater obligates. All seagrass and SAV provide key biological functions within the enclosed bays, estuaries, a...

  1. EAARL Submerged Topography - U.S. Virgin Islands 2003 (United States)

    Nayegandhi, Amar; Brock, John C.; Wright, C. Wayne; Stevens, Sara; Yates, Xan; Bonisteel, Jamie M.


    These remotely sensed, geographically referenced elevation measurements of Lidar-derived submerged topography were produced as a collaborative effort between the U.S. Geological Survey (USGS), Florida Integrated Science Center (FISC), St. Petersburg, FL; the National Park Service (NPS), South Florida-Caribbean Network, Miami, FL; and the National Aeronautics and Space Administration (NASA), Wallops Flight Facility, VA. This project provides highly detailed and accurate bathymetric datasets of a portion of the U.S. Virgin Islands, acquired on April 21, 23, and 30, May 2, and June 14 and 17, 2003. The datasets are made available for use as a management tool to research scientists and natural resource managers. An innovative airborne Lidar instrument originally developed at the NASA Wallops Flight Facility, and known as the Experimental Advanced Airborne Research Lidar (EAARL), was used during data acquisition. The EAARL system is a raster-scanning, waveform-resolving, green-wavelength (532-nanometer) Lidar designed to map near-shore bathymetry, topography, and vegetation structure simultaneously. The EAARL sensor suite includes the raster-scanning, water-penetrating full-waveform adaptive Lidar, a down-looking red-green-blue (RGB) digital camera, a high-resolution multi-spectral color infrared (CIR) camera, two precision dual-frequency kinematic carrier-phase GPS receivers, and an integrated miniature digital inertial measurement unit, which provide for submeter georeferencing of each laser sample. The nominal EAARL platform is a twin-engine Cessna 310 aircraft, but the instrument may be deployed on a range of light aircraft. A single pilot, a Lidar operator, and a data analyst constitute the crew for most survey operations. This sensor has the potential to make significant contributions in measuring sub-aerial and submarine coastal topography within cross-environmental surveys. Elevation measurements were collected over the survey area using the EAARL system, and

  2. Anatomy of floating and submerged leaves of heterophyllous plant of Nymphaea candida L.


    E.N. Klimenko


    The data on anatomy of floating and submerged leaves of heterophyllous aquatic plant Nymphaea candida L. are presented. Anatomy of floating leaves is shown to be different from that of submerged leaves: the absence of stomata, asterosclereids, and differentiated parenchyma, as well as by reduce intercellular volume and leaf width. Common patterns of leaf structure plasticity of aquatic heterophyllous plants in dependence on the environment are discussed.

  3. Aquatic adventitious root development in partially and completely submerged wetland plants Cotula coronopifolia and Meionectes brownii. (United States)

    Rich, Sarah Meghan; Ludwig, Martha; Colmer, Timothy David


    A common response of wetland plants to flooding is the formation of aquatic adventitious roots. Observations of aquatic root growth are widespread; however, controlled studies of aquatic roots of terrestrial herbaceous species are scarce. Submergence tolerance and aquatic root growth and physiology were evaluated in two herbaceous, perennial wetland species Cotula coronopifolia and Meionectes brownii. Plants were raised in large pots with 'sediment' roots in nutrient solution and then placed into individual tanks and shoots were left in air or submerged (completely or partially). The effects on growth of aquatic root removal, and of light availability to submerged plant organs, were evaluated. Responses of aquatic root porosity, chlorophyll and underwater photosynthesis, were studied. Both species tolerated 4 weeks of complete or partial submergence. Extensive, photosynthetically active, aquatic adventitious roots grew from submerged stems and contributed up to 90 % of the total root dry mass. When aquatic roots were pruned, completely submerged plants grew less and had lower stem and leaf chlorophyll a, as compared with controls with intact roots. Roots exposed to the lowest PAR (daily mean 4.7 ± 2.4 µmol m(-2) s(-1)) under water contained less chlorophyll, but there was no difference in aquatic root biomass after 4 weeks, regardless of light availability in the water column (high PAR was available to all emergent shoots). Both M. brownii and C. coronopifolia responded to submergence with growth of aquatic adventitious roots, which essentially replaced the existing sediment root system. These aquatic roots contained chlorophyll and were photosynthetically active. Removal of aquatic roots had negative effects on plant growth during partial and complete submergence.

  4. Agenesis of premolar associated with submerged primary molar and a supernumerary premolar: An unusual case report

    Directory of Open Access Journals (Sweden)

    S. V. S. G. Nirmala


    Full Text Available The combination of submerged primary molar, agenesis of permanent successor with a supernumerary in the same place is very rare. The purpose of this article is to report a case of submerged mandibular left second primary molar with supernumerary tooth in the same region along with agenesis of second premolar in an 11-year-old girl, its possible etiological factors, and a brief discussion on treatment options.

  5. Parametric and Nonparametric Analysis of LANDSAT TM and MSS Imagery for Detecting Submerged Plant Communities (United States)

    Ackleson, S. G.; Klemas, V.


    The spatial, spectral and radiometric characteristics of LANDSAT TM and MSS imagery for detecting submerged aquatic vegetation are assessed. The problem is approached from two perspectives; purely stochastic or nonparametric in a radiative sense and theoretical in which radiative transfer equations are used to predict upwelling radiance at satellite altitude. The spectral and radiometric aspects of the theoretical approach are addressed with which a submerged plant canopy is distinguished from a surrounding bottom of sand or mud.

  6. Simultaneous treatment of NO and SO{sub 2} with aqueous NaClO{sub 2} solution in a wet scrubber combined with a plasma electrostatic precipitator

    Energy Technology Data Exchange (ETDEWEB)

    Park, Hyun-Woo [Department of Chemistry and Chemical Engineering and Regional Innovation Center for Environmental Technology of Thermal Plasma (RIC-ETTP), INHA University, 100 Inha-ro, Nam-gu, Incheon 402-751 (Korea, Republic of); Choi, Sooseok, E-mail: [Department of Nuclear and Energy Engineering, Jeju National University, 102 Jejudaehak-ro, Jeju-si, Jeju Special Self-Governing Province, 690-756 (Korea, Republic of); Park, Dong-Wha, E-mail: [Department of Chemistry and Chemical Engineering and Regional Innovation Center for Environmental Technology of Thermal Plasma (RIC-ETTP), INHA University, 100 Inha-ro, Nam-gu, Incheon 402-751 (Korea, Republic of)


    Highlights: • This study was conducted to investigate simultaneous removal of NO and SO{sub 2}. • Proposed process consists of wet chemical reactor and non-thermal plasma reactor. • In the wet chemical reactor, NO and SO{sub 2} were absorbed and oxidized by NaClO{sub 2}. • In the non-thermal plasma reactor, aerosol particles were collected on anode surface. • NO and SO{sub 2} were removed more efficiently by proposed process than other methods. - Abstract: NO and SO{sub 2} gases that are generally produced in thermal power plants and incinerators were simultaneously removed by using a wet scrubber combined with a plasma electrostatic precipitator. The wet scrubber was used for the absorption and oxidation of NO and SO{sub 2}, and non-thermal plasma was employed for the electrostatic precipitation of aerosol particles. NO and SO{sub 2} gases were absorbed and oxidized by aerosol particles of NaClO{sub 2} solution in the wet scrubber. NO and SO{sub 2} reacted with the generated NaClO{sub 2} aerosol particles, NO{sub 2} gas, and aqueous ions such as NO{sub 2}{sup −}, NO{sub 3}{sup −}, HSO{sub 3}{sup −}, and SO{sub 4}{sup 2−}. The aerosol particles were negatively charged and collected on the surface of grounded anode in the plasma electrostatic precipitator. The NO and SO{sub 2} removal efficiencies of the proposed system were 94.4% and 100% for gas concentrations of 500 mg/m{sup 3} and a total gas flow rate of 60 Nm{sup 3}/h, when the molar flow rate of NaClO{sub 2} and the gas–liquid contact time were 50 mmol/min and 1.25 s, respectively. The total amount and number of aerosol particles in the exhaust gas were reduced to 7.553 μg/m{sup 3} and 210 /cm{sup 3} at the maximum plasma input power of 68.8 W, which are similar to the values for clean air.

  7. Antiinflammatory activity of the antirheumatic herbal drug, gravel root (Eupatorium purpureum): further biological activities and constituents. (United States)

    Habtemariam, S


    Previous reports from this laboratory revealed that cistifolin from the antirheumatic herbal drug, gravel root (rhizome of Eupatorium purpureum), showed activity both in in vitro and in vivo models of inflammation. Data are now presented to show that, in addition to the LFA-1 and other integrin-mediated leucocyte adhesions, cistifolin inhibits the Mac-1 (CD11b/CD18)-dependent monocyte adhesion to fibrinogen in a concentration-dependent manner. Further phytochemical analysis of the crude extract also led to the isolation of three known benzofurans, euparin, euparone, 6-hydroxy-3beta-methoxytrematone and a new benzofuran, 5-acetyl-6-hydroxy-2-(1-oxo-2-acetoxy-ethyl)-benzofuran. None of these compounds were active in suppressing integrin-mediated monocytic U937 cell adhesions in vitro. Copyright 2001 John Wiley & Sons, Ltd.

  8. Valley Width Variation Controls on Riffle Location and Persistence on a Gravel Bed River (United States)

    White, J. Q.; Pasternack, G. B.


    Numerous studies have examined the effect of constrictions on the formation of riffles and pools in rivers. Low velocity backwater effects are created above the constriction, with steep water surface slopes and flow acceleration after it. Such flow conditions cause varying sediment transport capacity, influencing the formation of riffles and pools near constrictions. Studies have shown that local bedrock outcrops, alluvial fans, sediment bars, and wood are capable of functioning as constrictions, but few address channel-confining valley walls as potential constrictions. Can variations in valley width influence riffle location and persistence? To address this question, research was performed on a valley-confined wandering gravel-bed reach of the regulated lower Yuba River from the Narrows Pool to the Highway 20 bridge. This reach has an average valley width of 164 m (range of 102-314 m). During 1853-1884, hydraulic gold mining filled this 7-km reach with ~26 m of mixed coarse sediment (totaling ~9-18 million cubic meters), creating a dynamic fluvial landscape comparable to recently deglaciated wandering gravel-bed streams. The hypothesis of this study was that riffles that persist over decades on wandering gravel-bed rivers are controlled by valley width variations. The study objectives were to (1) assess planform and elevation changes over 22 years and (2) correlate locations of persistent riffles with valley- wall constrictions. ArcGIS was used to measure valley width and changes in planform wetted area in georectified photo sets of this reach for 1984, 1986, 1991, 1996, 2002, 2004, 2005, and 2006. Detailed river valley DEMs were also available for 1999 and 2006 for measuring the recent incision rate, and pattern of the valley fill. Riffle crest locations for each year were plotted along with the valley width versus distance upstream, and all riffles crests that persisted for the entire duration were identified. The persistent riffle crests were statistically

  9. Use of macrophyte plants, sand & gravel materials in constructed wetlands for greywater treatment (United States)

    Qomariyah, S.; Ramelan, AH; Sobriyah; Setyono, P.


    Greywater discharged without any treatments into drainage channels or natural water bodies will lead to environmental degradation and health risk. Local macrophyte plants combined with natural materials of sand and gravel have been used in a system of constructed wetland for the treatment of the greywater. This paper presents the results of some studies of the system carried out in Indonesia, Thailand, and Costa Rica. The studies demonstrate the success of the constructed wetland systems in removing some pollutants of BOD, COD, TSS, pathogen, and detergent. The studies resulted in the treated water in a level of treatment that fulfils the requirement of the local standards for wastewater reuse as irrigation water, fishery, or other outdoor needs.

  10. Growth rate, protein:RNA ratio and stoichiometric homeostasis of submerged macrophytes under eutrophication stress

    Directory of Open Access Journals (Sweden)

    Xing W.


    Full Text Available Growth rate hypothesis (GRH and stoichiometric homeostasis of photoautotrophs have always been questioned. However, little is known about GRH and stoichiometric homeostasis of aquatic plants, especially submerged macrophytes. Therefore, we aim to test the GRH and explore stoichiometric homeostasis of four freshwater submerged macrophytes under eutrophication stress. At the single species level and the multi-species level, N:P ratios of Potamogeton maackianus, Myriophyllum spicatum, Vallisneria natans and Ceratophyllum demersum had no consistent trends with growth rates. However, protein:RNA ratios of P. maackianus, M. spicatum and V. natans all correlated negatively with growth rates, demonstrating GRH can apply to freshwater submerged macrophytes, even though they are threatening by eutrophication stress. Protein:RNA ratios positively correlated with N:P ratios in culture media and tissues in submerged macrophytes except in P. maackianus (30d, suggesting effects of varying N:P ratios in culture media on protein:RNA ratios are basically in concert with tissue N:P ratios under short-time eutrophication stress. Stoichiometric homeostasis coefficients (HN:P indicated submerged macrophytes have weak homeostasis. Stoichiometric homeostasis of V. natans was stronger than those of P. maackianus, M. spicatum and C. demersum. The differences in GRH and homeostasis of the four submerged macrophytes may be due to species traits.

  11. Sampling surface and subsurface particle-size distributions in wadable gravel-and cobble-bed streams for analyses in sediment transport, hydraulics, and streambed monitoring (United States)

    Kristin Bunte; Steven R. Abt


    This document provides guidance for sampling surface and subsurface sediment from wadable gravel-and cobble-bed streams. After a short introduction to streams types and classifications in gravel-bed rivers, the document explains the field and laboratory measurement of particle sizes and the statistical analysis of particle-size distributions. Analysis of particle...

  12. Comparison of Machine Learning methods for incipient motion in gravel bed rivers (United States)

    Valyrakis, Manousos


    Soil erosion and sediment transport of natural gravel bed streams are important processes which affect both the morphology as well as the ecology of earth's surface. For gravel bed rivers at near incipient flow conditions, particle entrainment dynamics are highly intermittent. This contribution reviews the use of modern Machine Learning (ML) methods implemented for short term prediction of entrainment instances of individual grains exposed in fully developed near boundary turbulent flows. Results obtained by network architectures of variable complexity based on two different ML methods namely the Artificial Neural Network (ANN) and the Adaptive Neuro-Fuzzy Inference System (ANFIS) are compared in terms of different error and performance indices, computational efficiency and complexity as well as predictive accuracy and forecast ability. Different model architectures are trained and tested with experimental time series obtained from mobile particle flume experiments. The experimental setup consists of a Laser Doppler Velocimeter (LDV) and a laser optics system, which acquire data for the instantaneous flow and particle response respectively, synchronously. The first is used to record the flow velocity components directly upstream of the test particle, while the later tracks the particle's displacements. The lengthy experimental data sets (millions of data points) are split into the training and validation subsets used to perform the corresponding learning and testing of the models. It is demonstrated that the ANFIS hybrid model, which is based on neural learning and fuzzy inference principles, better predicts the critical flow conditions above which sediment transport is initiated. In addition, it is illustrated that empirical knowledge can be extracted, validating the theoretical assumption that particle ejections occur due to energetic turbulent flow events. Such a tool may find application in management and regulation of stream flows downstream of dams for stream

  13. Positive and negative impacts of five Austrian gravel pit lakes on groundwater quality. (United States)

    Muellegger, Christian; Weilhartner, Andreas; Battin, Tom J; Hofmann, Thilo


    Groundwater-fed gravel pit lakes (GPLs) affect the biological, organic, and inorganic parameters of inflowing groundwater through combined effects of bank filtration at the inflow, reactions within the lake, and bank filtration at the outflow. GPLs result from wet dredging for sand and gravel and may conflict with groundwater protection programs by removing the protective soil cover and exposing groundwater to the atmosphere. We have investigated the impact on groundwater of five GPLs with different sizes, ages, and mean residence times, and all having low post-excavation anthropogenic usage. The results revealed highly active biological systems within the lake water, in which primary producers significantly reduced inflowing nitrate concentrations. Decalcification also occurred in lake water, reducing water hardness, which could be beneficial for waterworks in hard groundwater areas. Downgradient groundwater nitrate and calcium concentrations were found to be stable, with only minor seasonal variations. Biological degradation of organic material and organic micropollutants was also observed in the GPLs. For young GPLs adequate sediment deposits may not yet have formed and degradation processes at the outflow may consequently not yet be well established. However, our results showed that within 5 years from the cessation of excavation a protective sediment layer is established that is sufficient to prevent the export of dissolved organic carbon to downgradient groundwater. GPLs can improve groundwater quality in anthropogenically (e.g., pesticides and nitrate) or geologically (e.g., hardness) challenging situations. However, post-excavation usage of GPLs is often dominated by human activities such as recreational activities, water sports, or fish farming. These activities will affect lake and groundwater quality and the risks involved are difficult to predict and monitor and can lead to overall negative impacts on groundwater quality. Copyright © 2012 Elsevier B

  14. Convergent Hydraulics and Knickpoint Migration in an Incising Gravel-Cobble River (United States)

    Wyrick, J. R.; Pasternack, G. B.


    Regulated gravel-cobble rivers are known to incise, but the mechanism of incision is not well documented by process-based research. Widespread use of simple "stream power law" equations assumes that incision is caused by continuous downcutting that increases with discharge. To provide an alternate explanation that recognizes the inherent non-uniformity of natural channels, we hypothesize that regulated rivers experience waves of migrating knickpoints that retreat through riffles during low flow when riffle crests function as supercritical weirs and are rejuvenated by floods that downcut the intervening width-constricted pools. To test this new hypothesis, monitoring was performed on the rapidly incising 7-km Timbuctoo Bend of the lower Yuba River, CA, where 463,000 cubic meters of sediment have been scoured out in just the last seven years alone. Direct field measurements of velocity and depth fields were obtained at three migrating, horseshoe-shaped knickpoints in this reach. Also, detailed channel DEMs were obtained at different stages of knickpoint migration to track geomorphic change over seven years. At one of the knickpoints, a special torque sensor was deployed to map near-bed lift and drag stress components. Velocity fields reveal convergent hydraulics controlled by the horseshoe morphology that focus scour in the upstream center of the U-shape. At a relatively low discharge, supercritical flow and near-critical standing waves were observed. Furthermore, the peak near-bed drag stress that was directly measured exceeded 1000 Pa during this relatively low discharge regime, which explains why the bedforms are retreating so rapidly. These direct measurements were compared to similar measurements previously reported for horseshoe waterfalls analyzed in a flume, and will aid in determining the real mechanism for knickpoint migration and channel incision in regulated gravel-cobble rivers.

  15. Structural and Acoustic Responses of a Submerged Stiffened Conical Shell

    Directory of Open Access Journals (Sweden)

    Meixia Chen


    Full Text Available This paper studies the vibrational behavior and far-field sound radiation of a submerged stiffened conical shell at low frequencies. The solution for the dynamic response of the conical shell is presented in the form of a power series. A smeared approach is used to model the ring stiffeners. Fluid loading is taken into account by dividing the conical shell into narrow strips which are considered to be local cylindrical shells. The far-field sound pressure is solved by the Element Radiation Superposition Method. Excitations in two directions are considered to simulate the loading on the surface of the conical shell. These excitations are applied along the generator and normal to the surface of the conical shell. The contributions from the individual circumferential modes on the structural responses of the conical shell are studied. The effects of the external fluid loading and stiffeners are discussed. The results from the analytical models are validated by numerical results from a fully coupled finite element/boundary element model.

  16. [Submerged cultivation and chemical composition of Hericium erinaceus mycelium]. (United States)

    Avtonomova, A V; Bakanov, A V; Shuktueva, M I; Vinokurov, V A; Popova, O V; Usov, A I; Krasnopol'skaia, L M


    Submerged cultivation of Hericium erinaceus in various media was studied. The yield of the biomass was shown to depend mainly on the carbon source, whereas the content of water soluble polysaccharides depended mainly on the nitrogen source. The optimal medium composition provided the biomass yield of 21-23 g/l in 7 days. The biomass was characterized by the content of total protein, lipids and carbohydrates. In addition, the amino acid composition of the biomass was determined and shown to meet all the requirements of FAO/WHO concerning the amounts of essential amino acids (with exception of tryptophane). Oleinic and linoleic acids were identified as the main components of the fatty acids. Two water soluble polysaccharide fractions differing in solubility in aqueous ethanol were isolated and shown to contain rhamnose, fucose, xylose, glucose and galactose in different proportions. Vitamins B1, B2, B6, PP and E, ergosterol and coenzyme Q were also detected in the biomass of H. erinaceus.

  17. Underwater Photosynthesis of Submerged Plants – Recent Advances and Methods (United States)

    Pedersen, Ole; Colmer, Timothy D.; Sand-Jensen, Kaj


    We describe the general background and the recent advances in research on underwater photosynthesis of leaf segments, whole communities, and plant dominated aquatic ecosystems and present contemporary methods tailor made to quantify photosynthesis and carbon fixation under water. The majority of studies of aquatic photosynthesis have been carried out with detached leaves or thalli and this selectiveness influences the perception of the regulation of aquatic photosynthesis. We thus recommend assessing the influence of inorganic carbon and temperature on natural aquatic communities of variable density in addition to studying detached leaves in the scenarios of rising CO2 and temperature. Moreover, a growing number of researchers are interested in tolerance of terrestrial plants during flooding as torrential rains sometimes result in overland floods that inundate terrestrial plants. We propose to undertake studies to elucidate the importance of leaf acclimation of terrestrial plants to facilitate gas exchange and light utilization under water as these acclimations influence underwater photosynthesis as well as internal aeration of plant tissues during submergence. PMID:23734154

  18. Immunomodulatory properties of Grifola frondosa in submerged culture. (United States)

    Wu, Ming-Jiuan; Cheng, Tso-Lin; Cheng, Su-Yun; Lian, Tzi-Wei; Wang, Lisu; Chiou, Shu-Yuan


    Maitake (Grifola frondosa) is a popular mushroom in Asia for its tasty flavor and immune-stimulating property. The aim of the study is to investigate the innate immunity augmentation effects of different extracts of mycelia and culture filtrate from G. frondosa in submerged cultures. The hot water extract of mycelia showed the strongest cytokine induction effect as a function of its concentration in human whole blood culture. The most potent fractions of hot water extract, Fr. I and II, were mainly composed of polysaccharides with molecular masses of 43-140 and 13-38 kDa, respectively. These fractions (0.025 mg/mL) showed marked activity in enhancing phagocytosis of human polymorphonuclear neutrophils (PMN). In parallel, the expression of CD11b, an early marker of PMN activation, was also up-regulated dose dependently. This result suggested that complement receptor 3 was primed by these fractions. In addition to activation of phagocytes, these bioactive fractions also increased human peripheral blood natural killer cell cytotoxicity. These results imply that the relatively low molecular mass polysaccharides isolated from mycelia of G. frondosa can enhance innate immunity in vitro and therefore may serve as biological response modifiers.

  19. The use of bottle caps as submerged aerated filter medium. (United States)

    Damasceno de Oliveira, Laurence; Motlagh, Amir Mohaghegh; Goel, Ramesh; de Souza Missagia, Beatriz; Alves de Abreu Filho, Benício; Lautenschlager, Sandro Rogério


    In this study, a submerged aerated filter (SAF) using bottle caps as a support medium was evaluated. The system was fed with effluent from an upflow anaerobic sludge blanket system at ETE 2-South wastewater treatment plant, under different volumetric organic load rates (VOLRs). The population of a particular nitrifying microbial community was assessed by fluorescent in situ hybridization with specific oligonucleotide probes. The system showed an average removal of chemical oxygen demand (COD) equal to 76% for VOLRs between 2.6 and 13.6 kg COD m(-3) The process of nitrification in conjunction with the removal of organic matter was observed from applying VOLRs lower than 5.5 kg COD m(-3) resulting in 78% conversion of NH4(+)-N. As the applied organic load was reduced, an increase in the nitrifying bacteria population was observed compared with total 4'-6-diamidino-2-phenylindole (DAPI) stained cells. Generally, SAF using bottle caps as a biological aerated filter medium treating wastewater from an anaerobic system showed promising removal of chemical oxygen demand (COD) and conversion of NH4(+)-N.

  20. Stainless steel submerged arc weld fusion line toughness

    Energy Technology Data Exchange (ETDEWEB)

    Rosenfield, A.R.; Held, P.R.; Wilkowski, G.M. [Battelle, Columbus, OH (United States)


    This effort evaluated the fracture toughness of austenitic steel submerged-arc weld (SAW) fusion lines. The incentive was to explain why cracks grow into the fusion line in many pipe tests conducted with cracks initially centered in SAWS. The concern was that the fusion line may have a lower toughness than the SAW. It was found that the fusion line, Ji. was greater than the SAW toughness but much less than the base metal. Of greater importance may be that the crack growth resistance (JD-R) of the fusion line appeared to reach a steady-state value, while the SAW had a continually increasing JD-R curve. This explains why the cracks eventually turn to the fusion line in the pipe experiments. A method of incorporating these results would be to use the weld metal J-R curve up to the fusion-line steady-state J value. These results may be more important to LBB analyses than the ASME flaw evaluation procedures, since there is more crack growth with through-wall cracks in LBB analyses than for surface cracks in pipe flaw evaluations.

  1. Channel adjustments and vegetation cover dynamics in a large gravel bed river over the last 200 years (United States)

    Comiti, F.; Da Canal, M.; Surian, N.; Mao, L.; Picco, L.; Lenzi, M. A.


    The timing and extent of the morphological changes that occurred in the last 200 years in a large gravel bed river (the Piave River, eastern Italian Alps) that was heavily impacted by human activities (training structures, hydropower schemes, and gravel mining) have been analyzed by historical maps, aerial photos, repeated topographic measurements, and geomorphological surveys. Results show that the channel underwent a strong narrowing during the twentieth century, but with a faster pace during the 1970s-1990s and with an associated shift from a dominant braided pattern to a wandering morphology. Bed incision up to 2 m — mostly from gravel mining — has been documented for this period. Large areas of the former active channel were colonized by riparian forests, both as islands and as marginal woodlands. The ceasing of gravel extraction in the late 1990s seems to have determined a reversal in the evolutionary trend, with evidence of vegetation erosion/channel widening even though a significant aggradation phase is not present. We conclude that alteration of sediment regime has played a major role on the long-term channel evolution. However, only relevant flood events ( RI > 10-15 years) appear to determine substantial island erosion, and therefore the proportion of island vs. channel area fluctuates depending on flood history.

  2. Can rapid assessment protocols be used to judge sediment impairment in gravel-bed streams? A commentary (United States)

    Thomas E. Lisle; John M. Buffington; Peter R. Wilcock; Kristin Bunte


    Land management agencies commonly use rapid assessments to evaluate the impairment of gravel-bed streams by sediment inputs from anthropogenic sources. We question whether rapid assessment can be used to reliably judge sediment impairment at a site or in a region. Beyond the challenges of repeatable and accurate sampling, we argue that a single metric or protocol is...

  3. Influence of hyporheic flow and geomorphology on temperature of a large, gravel-bed river, Clackamas River, Oregon, USA (United States)

    Vol. 22 Hydrological Processes


    The hyporheic zone influences the thermal regime of rivers, buffering temperature by storing and releasing heat over a range of timesscales. We examined the relationship between hyporheic exchange and temperature along a 24-km reach of the lower Clackamas River, a large gravel-bed river in northwestern Oregon (median discharge = 75·7 m3/s;...

  4. Flow structure through pool-riffle sequences and a conceptual model for their sustainability in gravel-bed rivers (United States)

    D. Caamano; P. Goodwin; J. M. Buffington


    Detailed field measurements and simulations of three-dimensional flow structure were used to develop a conceptual model to explain the sustainability of self-formed pool-riffle sequences in gravel-bed rivers. The analysis was conducted at the Red River Wildlife Management Area in Idaho, USA, and enabled characterization of the flow structure through two consecutive...

  5. An Investigation into the Processes and Quantity of Dust Emissions over Gravel and Sand Deserts in North-Western China (United States)

    Zhang, Zhengcai; Dong, Zhibao; Qian, Guangqian; Wu, Guoxi; Cui, Xujia


    Year-long field observations have shown that there are spatial and temporal variations in the quantity of dust emissions for particulate matter {deserts, we found that gravel deserts and sandy deserts are both major sources of dust for dust storms in this region.


    Several geochemical properties of an aquifer sediment that control metal-ion adsorption were investigated to determine their potential use as indicators of the spatial variability of metal adsorption. Over the length of a 4.5-m-long core from a sand and gravel aquifer, lead (Pb2+...


    Directory of Open Access Journals (Sweden)

    V. V. Ivashechkin


    Full Text Available The purpose of this work is the study of decolmatation rate of granular layer of gravel pack of well during creating inside of it flushing of reagent with given hydrodynamic parameters and determination the duration of treatment. This article deals with radical movement of chemical solutions by injection of it outside of gravel pack of filter when the flow directs to borehole axis under conditions of quasi-steady-state mode of filtration for equal yield of input and output reagent from borehole.Colmataged layer of gravel pack is schematized in the form of porous ring cylinder with outside radius which is equal to radius of line of gravel pack and the height which is equal to the length of filter made in formation drilling and inside radius which is equal to radius of filter. Initial saturation of subsoil with colmatant is given. It was accepted that reagent with given rate flows through outside surface of ring cylinder equal along all height. Near-filtering zone is given uniform and movement is quasi-steady-state.Equations’ system is composed including: joint equation of movement and mass conservation and generalized equation of kinetics, which describes kinetics of colmatant dissolution in the regime of out-pipe watering of ring gravel pack of well taking into account the change of structure of porous medium. The analytic solution of equations’ system was obtained, which allow to calculate salt content in reagent during the leaching process and to determine the specific volume of deposits in the point of gravel pack at any moment of time in the process of regent injection. The analytic dependence was obtained for calculation of duration of complete regeneration of soil grains’ layer of outer contour of gravel packing. For calculation of duration of full regeneration of the whole thickness of packing it is suggested to divide the regeneration period into a series of stages of salt transferring from subsoil. Duration of one stage is equal

  8. Real Time Monitoring of NH3 Concentration Using Diffusion Scrubber Sampling Technique and Result of Application to the Processing of Chemically Amplified Resists (United States)

    Park, Jungchul; Bae, Eunyoung; Park, Chungeun; Han, Woosung; Koh, Youngbum; Lee, Moonyoung; Lee, Jonggil


    The application of chemically amplified resist is known to cause a problem in the accurate measurement of the concentration of basic gas species ( NH3, N-methylpyrrolidone (NMP)) in a clean room environment because it is sensitive to its environment. Among various methods of measurement, diffusion scrubber sampling method was selected and tested. The environmental sensitivity of a commercial chemically amplified resist, APEX-E, was also tested. For the concentration measurement, the method proved to be suitable for automation and good for measuring NH3 concentration as low as the sub ppb level (limit of detection ˜0.08 ppb). Some measurement results concerning various aspects of application are presented. Test results of the environmental stability of chemically amplified resists showed that NH3 concentration should be controlled to at least under 7.5 ppb for maintaining the process stability.

  9. Inhibition of the Nitrification Process of Activated Sludge Micro-Organism by Scrubber Water from an Industrial Flue Gas Cleaning Process

    DEFF Research Database (Denmark)

    Thomsen, Jens Peter


    The microbial transformation of ammonia to nitrate, the nitrification, is a central process in the nitrogen biogeochemical cycle. In a modern wastewater treatment plant, the nitrification process is a key process in the removal of nitrogen and inhibitory compounds in sewage can seriously affect...... the nitrogen removal. A major sewage cleaning plant in the southern part of Denmark is a recipient of industrial sewage from a major fish meal industry. Severe nitrification inhibition was observed in scrubber water from an incineration of process air, and the processes that lead to the production were stopped....... In order to investigate the relation between incineration temperatures and the production of inhibitory compounds, the process air was burned at temperatures from 800°C to 1000°C. The termically affected condensate was collected and the nitrification inhibition effect of the condensate was tested using...

  10. Early Human Dispersals and Submerged Landscapes : comment on news feature "Migration: value of submerged early sites" in Nature's May 2012 special issue "Peopling the Planet"

    NARCIS (Netherlands)

    Flemming, Nicholas; Bailey, Geoffrey N.; Sakellariou, Dimitris; Arias, Pablo; Canals, M.; Chiocci, Francesco Latino; Cohen, K.M.; Erlandson, Jon; Faught, Michael K.; Flatman, Joe; Fischer, Anders; Galili, Ehud; Harff, Jan; Lericolais, Gilles; Lűth, Friedrich


    Your articles on human dispersal in the late Pleistocene epoch (Nature 485, 23; 2012) overlook the significance of now-submerged archaeological sites on the continental shelf during this period (126,000–11,000 years ago). It is wrong to assume that these were completely destroyed by the sea and that

  11. Differential Response of Floating and Submerged Leaves of Longleaf Pondweed to Silver Ions

    Directory of Open Access Journals (Sweden)

    Nisha Shabnam


    Full Text Available In this study, we have investigated variations in the potential of floating and submerged leaves of longleaf pondweed (Potamogeton nodosus to withstand silver ion (Ag+-toxicity. Both floating and submerged leaves changed clear colorless AgNO3 solutions to colloidal brown in the presence of light. Transmission electron microscopy revealed the presence of distinct crystalline Ag-nanoparticles (Ag-NPs in these brown solutions. Powder X-ray diffraction pattern showed that Ag-NPs were composed of Ag0 and Ag2O. Photosystem (PS II efficiency of leaves declined upon exposure to Ag+ with a significantly higher decline in the submerged leaves than in the floating leaves. Similarly, Ag+ treatment caused a significant reduction in the carboxylase activity of the ribulose bisphosphate carboxylase/oxygenase in leaves. The reduction in this carboxylase activity was significantly higher in the submerged than in the floating leaves. Ag+ treatment also resulted in a significant decline in the levels of non-enzymatic and enzymatic antioxidants; the decline was significantly lower in the floating than in submerged leaves. X-ray photoelectron spectroscopy revealed the presence of Ag2O in these leaves. Inductively coupled plasma mass spectrometry analysis revealed a three-fold higher Ag content in the submerged than in floating leaves. Our study demonstrates that floating leaves of longleaf pondweed have a superior potential to counter Ag+-toxicity compared with submerged leaves, which could be due to superior potential of floating leaves to reduce Ag+ to less/non-toxic Ag0/Ag2O-nanoparticles/nanocomplexes. We suggest that modulating the genotype of longleaf pondweed to bear higher proportion of floating leaves would help in cleaning fresh water bodies contaminated with ionic forms of heavy metals.

  12. Multi-Objective Optimization of Submerged Arc Welding Process

    Directory of Open Access Journals (Sweden)

    Saurav Datta


    Full Text Available Submerged arc welding (SAW is an important metal fabrication technology specially applied to join metals of large thickness in a single pass. In order to obtain an efficient joint, several process parameters of SAW need to be studied and precisely selected to improve weld quality. Many methodologies were proposed in the past research to address this issue. However, a good number of past work seeks to optimize SAWprocess parameters with a single response only. In practical situations, not only is the influence of process parameters and their interactive effects on output responses are to be critically examined but also an attempt is to be made to optimize more than one response, simultaneously. To this end, the present study considers four process control parameters viz. voltage (OCV, wire feed rate, traverse speed and electrode stick-out. The selected weld quality characteristics related to features of bead geometry are depth of penetration, reinforcement and bead width. In the present reporting, an integrated approach capable of solving the simultaneous optimization of multi-quality responses in SAW was suggested. In the proposed approach, the responses were transformed into their individual desirability values by selecting appropriate desirability function. Assuming equal importance for all responses, these individual desirability values were aggregated to calculate the overall desirability values. Quadratic Response Surface Methodology (RSM was applied to establish a mathematical model representing overall desirability as a function involving linear, quadratic and interaction effect of process control parameters. This model was optimized finally within the experimental domain using PSO (Particle Swarm Optimization algorithm. A confirmatory test showed a satisfactory result. A detailed methodology of RSM, desirability function (DF and a PSO-based optimization approach was illustrated in the paper.

  13. Fallout plume of submerged oil from Deepwater Horizon (United States)

    Valentine, David L.; Fisher, G. Burch; Bagby, Sarah C.; Nelson, Robert K.; Reddy, Christopher M.; Sylva, Sean P.; Woo, Mary A.


    The sinking of the Deepwater Horizon in the Gulf of Mexico led to uncontrolled emission of oil to the ocean, with an official government estimate of ∼5.0 million barrels released. Among the pressing uncertainties surrounding this event is the fate of ∼2 million barrels of submerged oil thought to have been trapped in deep-ocean intrusion layers at depths of ∼1,000–1,300 m. Here we use chemical distributions of hydrocarbons in >3,000 sediment samples from 534 locations to describe a footprint of oil deposited on the deep-ocean floor. Using a recalcitrant biomarker of crude oil, 17α(H),21β(H)-hopane (hopane), we have identified a 3,200-km2 region around the Macondo Well contaminated by ∼1.8 ± 1.0 × 106 g of excess hopane. Based on spatial, chemical, oceanographic, and mass balance considerations, we calculate that this contamination represents 4–31% of the oil sequestered in the deep ocean. The pattern of contamination points to deep-ocean intrusion layers as the source and is most consistent with dual modes of deposition: a “bathtub ring” formed from an oil-rich layer of water impinging laterally upon the continental slope (at a depth of ∼900–1,300 m) and a higher-flux “fallout plume” where suspended oil particles sank to underlying sediment (at a depth of ∼1,300–1,700 m). We also suggest that a significant quantity of oil was deposited on the ocean floor outside this area but so far has evaded detection because of its heterogeneous spatial distribution. PMID:25349409

  14. Submergence Causes Similar Carbohydrate Starvation but Faster Post-Stress Recovery than Darkness in Alternanthera philoxeroides Plants.

    Directory of Open Access Journals (Sweden)

    Xiao Qi Ye

    Full Text Available Carbon assimilation by submerged plants is greatly reduced due to low light levels. It is hypothesized that submergence reduces carbohydrate contents and that plants recover from submergence in the same way as darkness-treated plants. To test this hypothesis, the responses of plants to submergence and darkness were studied and compared. Plants of a submergence-tolerant species, Alternanthera philoxeroides, were exposed to well drained and illuminated conditions, complete submergence conditions or darkness conditions followed by a recovery growth period in a controlled experiment. The biomass maintenance and accumulation, carbohydrate content dynamics and respiration rate in the plants were assessed to quantify the carbohydrate utilization rate and regrowth. The submerged plants maintained higher chlorophyll contents, more green leaf tissue and more biomass; recovered more quickly; and accumulated more carbohydrates and biomass than darkness-treated plants. The respiration rate was continuously reduced in the same pattern under both stress conditions but was maintained at a significantly lower level in the submerged plants; the total soluble sugar and total fructan contents were decreased at approximately the same rate of decrease, reaching similar low levels, in the two stress treatments. The A. philoxeroides plants were more tolerant of submergence than darkness. The faster recovery of desubmerged plants could not be explained by the similar carbohydrate contents at the start of recovery. Other types of carbon reserves besides carbohydrates or other mechanisms such as higher post-stress photosynthetic performance might be involved.

  15. Spatial patterns in gravel habitats and communities in the central and eastern English Channel (United States)

    Coggan, Roger; Barrio Froján, Christopher R. S.; Diesing, Markus; Aldridge, John


    The distribution of sediment type and benthic communities in the central and eastern English Channel is shown to be polarised around a distinctive local hydrodynamic feature. The seabed in the region includes an extensive area of gravel substrate which is both an important habitat for benthic marine fauna and a valuable source of material for the marine aggregate industry. Effective management of the area is predicated on an understanding of whether it represents a single homogeneous unit, or several different units that may need to be managed in different ways. The aim of this study was to provide information that would inform such management decisions. Spatial patterns in gravel habitats and communities were studied by investigating the physical environment through modelled and empirical data, and the distribution of infauna and epifauna along an east-west trending transect. A common spatial pattern was observed in both physical and biological parameters, but rather than indicating a simple longitudinal gradient, there was a distinct polarisation around a central feature, a bedload parting (BLP) zone situated between the Isle of Wight and Cotentin peninsula. Sediments and communities at the eastern and western ends of the transect were more similar to each other than to those in the middle. The strong hydrodynamic regime in the BLP area controls sediment distribution, transporting finer material, mainly sand, away from the mid transect area. The pattern in sand content of the substrate mirrors the magnitude of the potential bedload transport, which is complex in this region due to the interplay between the M2 and M4 tidal constituents and produced a series of erosional and depositional zones. The structure of benthic communities reflected the local substrate and hydrodynamic conditions, with sponges observed among the stable substrates and stronger currents that characterised the mid transect area, while infauna became more diverse towards the ends of the

  16. Analysing hyporheic exchange processes during unsteady flow in a small gravel bed river (United States)

    Kurtenbach, Andreas; Schuetz, Tobias; Krein, Andreas; Bierl, Reinhard


    Quantifying hyporheic exchange in gravel dominated rivers still remains a challenging task in stream ecology and hydrology, in particular during unsteady flow. We adopted three strategies to decipher exchange processes with the hyporheic zone during unsteady boundary conditions. First, artificial floods were generated in the mid-mountain gravel bed river system of the Olewiger Bach, Germany (24 km2). The advantage of the artificial flood approach lies in the selective control of governing processes by experimental design. Consequently, hydraulic boundary conditions such as maximum discharge, runoff volume and flood duration are steerable during the field experiments and the composition of the discharged water (e.g. low conductivity values) is known. Second, hyporheic exchange was analysed via heat dynamics using air, water and sediment pore water temperatures. Temperature dynamics in the hyporheic zone were monitored at the head, mid and tail of a riffle using specific lances (length: 67 cm, Ø: 3cm) containing temperature sensors in depths of 2, 5, 10, 15, 25, 45 and 65 cm. Short-term temperature variability during the unsteady artificial flood waves were analysed in high resolution of 10-30 seconds. In order to capture long-term seasonal fluctuations and dynamics during natural floods temperature was continuously measured at 5-min resolution. However, heat transfer in the hyporheic zone is affected by both advective and conductive transport. In a third strategy we therefore measure electrical conductivity and selected solutes in pore water during three artificial floods in 2015. Pore water was sampled from different sediment depths (5, 15, 25 and 45 cm) via stainless steel multilevel probes (length: 58 cm, Ø: 4cm). The investigation of temperature and pore water dynamics reveals that precedent hydrological conditions and ground-water levels are significant determinants for hyporheic exchange during unsteady flow. Stable groundwater stratification in spring for

  17. Characterisation of sand transport in gravel-bed rivers using iron slag dated by historical studies (United States)

    Houbrechts, G.; Levecq, Y.; Petit, F.


    Considerable quantities of iron-smelting slag are present in the bed of the Ardennian rivers. These waste products come from hundreds of ironworks (mainly blast furnaces and finery forges) built close to different-sized rivers between the 14th and the 19th centuries. In general, slag was crushed by hammers, sorted and piled up in heaps around the furnaces, generally onto the floodplains. Furthermore, some archives mention that they were sometimes thrown out directly into the rivers. This means that for centuries, slag elements have been swept away by floods, mixed with the sediment and spread out along river courses. Due to their distinctive appearance, slag particles are easily recognizable among the natural elements. Thanks to many historical studies conducted on the early iron industry, we are able to date quite precisely the inception and the periods of activity of the different sites established in the catchments. These data are indispensable in order to use slag as a tracer to quantify the particles' velocity in rivers. Downstream of ironworks, samples of sand have been collected in the surface layer of many gravel-bed rivers. Then, the slag concentration of each sample has been measured in the coarse sand fraction. The representation of the longitudinal evolution of slag concentration in these rivers permits the dispersion of slag to be analysed, the relative bed-material discharges at confluences to be quantified and the velocity of coarse sand to be determined. A survey of the bedload discharge in the Ardennian rivers established that more than 90 % of the bedload transport consists of coarse sand grains that are transported on the bottom of the bed. However, in the literature, this grain-size fraction is generally not considered in bedload discharge estimations because the sandy particles are very difficult to tag and to recover. Consequently, the huge amounts of slag injected in rivers several centuries ago can be considered as a very useful opportunity

  18. Solitary and cnoidal wave scattering by a submerged horizontal plate in shallow water

    Directory of Open Access Journals (Sweden)

    Masoud Hayatdavoodi


    Full Text Available Solitary and cnoidal wave transformation over a submerged, fixed, horizontal rigid plate is studied by use of the nonlinear, shallow-water Level I Green-Naghdi (GN equations. Reflection and transmission coefficients are defined for cnoidal and solitary waves to quantify the nonlinear wave scattering. Results of the GN equations are compared with the laboratory experiments and other theoretical solutions for linear and nonlinear waves in intermediate and deep waters. The GN equations are then used to study the nonlinear wave scattering by a plate in shallow water. It is shown that in deep and intermediate depths, the wave-scattering varies nonlinearly by both the wavelength over the plate length ratio, and the submergence depth. In shallow water, however, and for long-waves, only the submergence depth appear to play a significant role on wave scattering. It is possible to define the plate submergence depth and length such that certain wave conditions are optimized above, below, or downwave of the plate for different applications. A submerged plate in shallow water can be used as a means to attenuate energy, such as in wave breakers, or used for energy focusing, and in wave energy devices.

  19. [Influence of Submerged Plants on Microbial Community Structure in Sediment of Hongze Lake]. (United States)

    Zhang, Ding-yu; Zhang, Ting-xi; Dong, Dan-ping; Li, De-fang; Wang, Guo-xiang


    Phospholipid fatty acids (PLFAs) method was applied to analyze the influence of submerged plants on sediment microbial community structure, in order to investigate the changes of sediment microbial community structure for different kinds of the submerged plants in different growth periods. Particularly, Potamogeton crispus L., Potamogeton pectinatus L and the mixed group were chosen as the typical submerged plants in Hongze Lake for investigation in this paper. The results indicated that the change of total PLFAs in different periods was significant, on the contrary, the PLFA change for different groups in the same period was insignificant. The values of G⁺ PLFA/G⁻ PLFA in the submerged plant group were also highly related to the different growth periods, which demonstrated that the root function of the submerged plant had a severe impact on the microbial community in sediment. Furthermore, some environmental factors, such as Temperature, pH, TOC and DO, were correlated to characteristic phospholipid of PLFAs in sediment, which means the environmental factors could also affect the microbial community structure.

  20. Suspension of Egg Hatching Caused by High Humidity and Submergence in Spider Mites. (United States)

    Ubara, Masashi; Osakabe, Masahiro


    We tested the effects of high humidity and submergence on egg hatching of spider mites. In both the high humidity and submergence treatments, many Tetranychus and Panonychus eggs did not hatch until after the hatching peak of the lower humidity or unsubmerged controls. However, after humidity decreased or water was drained, many eggs hatched within 1-3 h. This was observed regardless of when high humidity or submergence treatments were implemented: either immediately after oviposition or immediately before hatching was due. Normal eyespot formation was observed in most eggs in the high humidity and submergence treatments, which indicates that spider mite embryos develop even when eggs are underwater. Therefore, delays in hatching are not caused by delayed embryonic development. A delay in hatching was always observed in Panonychus citri (McGregor) but was more variable in Tetranychus urticae Koch and Tetranychus kanzawai Kishida. The high humidity and submergence treatments affected but did not suppress larval development in these species. In contrast, many Oligonychus eggs died following the high humidity treatments. In Tetranychus and Panonychus spider mites, suspension of egg hatching may mitigate the adverse effects of rainfall. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email:

  1. Individual and combined suppressive effects of submerged and floating-leaved macrophytes on algal blooms. (United States)

    Seto, Mayumi; Takamura, Noriko; Iwasa, Yoh


    Shallow lakes and ponds are often characterised either by clear water with abundant submerged macrophytes or by turbid water with abundant phytoplankton. Blooms of toxic filamentous blue-green algae (cyanobacteria) often dominate the phytoplankton community in eutrophic lakes, which threatens ecological functions and biodiversity of freshwater ecosystems. We studied a simple lake model in order to evaluate individual and combined suppressive effects of rooted submerged and rooted floating-leaved macrophytes on algal blooms. Floating-leaved plants are superior competitors for light, whereas submerged plants absorb and reduce available phosphorus in a water column that rooted floating-leaved plants exploit to a lesser extent. We found that mixed vegetation that includes both submerged and floating-leaved plants is more resistant than vegetation comprised by a single plant type to algal invasion triggered by phosphorus loading. In addition, competitive exclusion of submerged plants by floating-leaved plants may promote an algal bloom. These predictions were confirmed by the decision tree analysis of field data from 35 irrigation ponds in Hyogo Prefecture, Japan. Copyright © 2012 Elsevier Ltd. All rights reserved.

  2. Constructed tropical wetlands with integrated submergent-emergent plants for sustainable water quality management. (United States)

    Tanaka, Norio; Jinadasa, K B S N; Werellagama, D R I B; Mowjood, M I M; Ng, W J


    Improvement of primary effluent quality by using an integrated system of emergent plants (Scirpus grossus in the leading subsurface flow arrangement) and submergent plants (Hydrilla verticillata in a subsequent channel) was investigated. The primary effluent was drawn from a septic tank treating domestic sewage from a student dormitory at the University of Peradeniya, Sri Lanka. Influent and effluent samples were collected once every 2 weeks from May 2004 through July 2005 and analyzed to determine water quality parameters. Both the emergent and submergent plants were harvested at predetermined intervals. The results suggested that harvesting prolonged the usefulness of the system and the generation of a renewable biomass with potential economic value. The mean overall pollutant removal efficiencies of the integrated emergent and submergent plant system were biological oxygen demand (BOD5), 65.7%; chemical oxygen demand (COD), 40.8%; ammonium (NH4+-N), 74.8%; nitrate (NO3--N), 38.8%; phosphate (PO43-), 61.2%; total suspended solids (TSS), 65.8%; and fecal coliforms, 94.8%. The submergent plant subsystem improved removal of nutrients that survived the emergent subsystem operated at low hydraulic retention times. The significant improvement in effluent quality following treatment by the submergent plant system indicates the value of incorporating such plants in wetland systems.

  3. The impact of ellipsoidal particle shape on pebble breakage in gravel. (United States)

    Tuitz, Christoph; Exner, Ulrike; Frehner, Marcel; Grasemann, Bernhard


    We have studied the influence of particle shape and consequently loading configuration on the breakage load of fluvial pebbles. Unfortunately, physical strength tests on pebbles, i.e., point-load tests, can only be conducted under one specific stable loading configuration. Therefore, the physical uniaxial strength tests performed in this study were extended by a two-dimensional finite-element stress analysis, which is capable of investigating those scenarios that are not possible in physical tests. Breakage load, equivalent to that measured in unidirectional physical tests, was determined from the results of the stress analysis by a maximum tensile stress-based failure criterion. Using this assumption, allows the determination of breakage load for a range of different kind of synthetic loading configurations and its comparison with the natural breakage load distribution of the physical strength tests. The results of numerical modelling indicated that the configuration that required the least breakage load corresponded with the minor principal axis of the ellipsoidal pebbles. In addition, most of the simulated gravel-hosted loading configurations exceeded the natural breakage load distribution of fluvial pebbles obtained from the physical strength tests.

  4. Observations of gravel beach dynamics during high energy wave conditions using a laser scanner (United States)

    Almeida, L. P.; Masselink, G.; Russell, P. E.; Davidson, M. A.


    A 2D laser-scanner was deployed at the high tide runup limit of a pure gravel beach (Loe Bar, Cornwall, England) to measure high-frequency (2.5 Hz) swash hydrodynamics and topographic changes during an energetic wave event. Measurements performed with the laser-scanner were corrected to compensate for levelling and orientation errors, and a variance threshold was applied to separate the beach topography from the water motions. Laser measurements were used to characterise the swash hydrodynamics and morphological changes during one tidal cycle through the calculation of several parameters, such as the 2% exceedence of the runup maxima (R2%), swash flow velocity skewness (), runup spectra and cumulative topographic changes. Results indicate that despite the small net morphological changes over the tide cycle, significant sediment mobilization occurs. A clear asymmetrical morphological response was found during the different tidal phases: the rising tide is dominated by accretion whilst the falling tide is dominated by erosion. The main factor controlling this asymmetrical morphological response is the step migration that, depending on the tide phase, controls the wave breaking point and consequently the dominant sediment transport direction. During the rising tide, step development decreases the shoreface slope and reduces the runup energy, whilst during the falling tide the step remobilization increases the shoreface slope and energy on the runup.

  5. Modelling nitrogen removal in a coupled HRP and unplanted horizontal flow subsurface gravel bed constructed wetland (United States)

    Mayo, A. W.; Mutamba, J.

    A coupled model was developed that incorporates all the major nitrogen transformation mechanisms influencing nitrogen removal in aquatic systems. The model simulates nitrogen transformation and removal processes in the high rate pond (HRP) and the subsurface constructed wetland unit (SSCW). The model considered organic nitrogen (ON), ammonia nitrogen (NH 3-N), and nitrate nitrogen ( NO3--N) as the major forms of nitrogen involved in the transformation chains. The influencing transformation mechanisms considered in the model include uptake of inorganic nitrogen by algae and bacteria, mineralization, sedimentation, volatilisation of ammonia and nitrification coupled with denitrification processes. The results showed that improved nitrogen removal occurred with increase in hydraulic time of the HRP unit. It was also revealed that the HRP can effectively be used to promote nitrification and subsurface flow gravel bed constructed wetland can be used as a denitrifying unit. The most efficient mechanisms were determined using a transformation model. The model indicated that nitrification and mineralization were dominant contributing 51.1% and 14.9%, respectively. Denitrification and mineralization were most significant in the SSCW accounting for 43.5% and 16.7%, respectively. Nitrification-denitrification route was observed to be the most significant mechanism for nitrogen removal in the coupled system with an overall contribution of 53%. The model predicted the overall nitrogen removal as 37% compared to 38.4% obtained from field measurements.

  6. Geologie study off gravels of the Agua Fria River, Phoenix, AZ (United States)

    Langer, W.H.; Dewitt, E.; Adams, D.T.; O'Briens, T.


    The annual consumption of sand and gravel aggregate in 2006 in the Phoenix, AZ metropolitan area was about 76 Mt (84 million st) (USGS, 2009), or about 18 t (20 st) per capita. Quaternary alluvial deposits in the modern stream channel of the Agua Fria River west of Phoenix are mined and processed to provide some of this aggregate to the greater Phoenix area. The Agua Fria drainage basin (Fig. 1) is characterized by rugged mountains with high elevations and steep stream gradients in the north, and by broad alluvial filled basins separated by elongated faultblock mountain ranges in the south. The Agua Fria River, the basin’s main drainage, flows south from Prescott, AZ and west of Phoenix to the Gila River. The Waddel Dam impounds Lake Pleasant and greatly limits the flow of the Agua Fria River south of the lake. The southern portion of the watershed, south of Lake Pleasant, opens out into a broad valley where the river flows through urban and agricultural lands to its confluence with the Gila River, a tributary of the Colorado River.

  7. Geochemical and Hydrogeological Controls on Arsenic in Sand-and-Gravel Aquifers in Central Illinois, USA (United States)

    Kelly, W. R.; Holm, T. R.; Wilson, S. D.; Roadcap, G. S.


    A total of 176 wells in sand-and-gravel aquifers in central Illinois were sampled for arsenic and other chemical parameters. These results were combined with archived and published data from several hundred well samples to characterize the spatial distribution of arsenic and determine the potential geochemical controls on its solubility and mobility. There was considerable spatial variability in the arsenic concentrations, and arsenic was not correlated with aquifer depth. There did not appear to be any arsenic "plumes" at the scale of the sampling. Arsenic solubility appeared to be controlled by oxidation-reduction conditions, especially the presence of organic matter. Geochemical conditions in the aquifers are typically reducing, but only in the most reducing waters does arsenic accumulate in solution. In wells in which sulfate was present, arsenic concentrations were low or below the detection limit (0.5 ig/L). Elevated arsenic concentrations were only found in wells where sulfate was absent or at low concentrations, indicating post-sulfate-reducing conditions. Methane was detected and organic carbon and ammonium concentrations were generally elevated in these wells. Iron is common in the aquifer sediments, and iron reduction appears to be occurring throughout the aquifers. Arsenic is likely released from the solid phase as iron oxide is reduced.

  8. PGDP Trichloroethene Biodegradation Investigation Summary Report: Regional Gravel Aquifer & Northwest Plume

    Energy Technology Data Exchange (ETDEWEB)

    Hampson, Steve [Univ. of Kentucky, Lexington, KY (United States). Kentucky Research Consortium for Energy and Environment


    The evaluation of biological degradation processes addressed by this report are part of a broad trichloroethene (TCE) Fate and Transport Investigation that includes four (4) topics of phased investigation (Table ES1) relative to degradation and/or attenuation of TCE in the Regional Gravel Aquifer (RGA) underlying the United States Department of Energy Paducah Gaseous Diffusion Plant (PGDP). In order of implementation the project phases are: (1) derivation of a TCE first-order rate constant by normalization of TCE values against technetium-99 (99Tc) and chloride. 2) identification of the presence of microbes capable of aerobic co-metabolic TCE biodegradation using enzyme activity probes (this report); 3) Compound-specific isotope analysis (CSIA) to support prevalence of biotic and/or abiotic degradation processes; and 4) evaluation of potential abiotic RGA-TCE attenuation mechanisms including sorption. This report summarizes the Phase II activities related to the identification and evaluation of biological degradation processes that may be actively influencing TCE fate and transport in the RGA contaminant plumes at the United States Department of Energy (DOE) PGDP and its environs (Figure ES1). The goals of these activities were to identify active biological degradation mechanisms in the RGA through multiple lines of evidence and to provide DOE with recommendations for future TCE biological degradation investigations.

  9. A new approach to define surface/sub-surface transition in gravel beds (United States)

    Haynes, Heather; Ockelford, Anne-Marie; Vignaga, Elisa; Holmes, William


    The vertical structure of river beds varies temporally and spatially in response to hydraulic regime, sediment mobility, grain size distribution and faunal interaction. Implicit are changes to the active layer depth and bed porosity, both critical in describing processes such as armour layer development, surface-subsurface exchange processes and siltation/ sealing. Whilst measurements of the bed surface are increasingly informed by quantitative and spatial measurement techniques (e.g., laser displacement scanning), material opacity has precluded the full 3D bed structure analysis required to accurately define the surface-subsurface transition. To overcome this problem, this paper provides magnetic resonance imaging (MRI) data of vertical bed porosity profiles. Uniform and bimodal (σ g = 2.1) sand-gravel beds are considered following restructuring under sub-threshold flow durations of 60 and 960 minutes. MRI data are compared to traditional 2.5D laser displacement scans and six robust definitions of the surface-subsurface transition are provided; these form the focus of discussion.

  10. Sediment heterogeneity and mobility in the morphodynamic modelling of gravel-bed braided rivers (United States)

    Singh, Umesh; Crosato, Alessandra; Giri, Sanjay; Hicks, Murray


    The effects of sediment heterogeneity and sediment mobility on the morphology of braided rivers are still poorly studied, especially when the partial sediment mobility occurs. Nevertheless, increasing the bed sediment heterogeneity by coarse sediment supply is becoming a common practice in river restoration projects and habitat improvement all over the world. This research provides a step forward in the identification of the effects of sediment sorting on the evolution of sediment bars and braiding geometry of gravel-bed rivers. A two-dimensional morphodynamic model was used to simulate the long-term developments of a hypothetical braided system with discharge regime and morphodynamic parameters derived from the Waimakariri River, New Zealand. Several scenarios, differing in bed sediment heterogeneity and sediment mobility, were considered. The results agree with the tendencies already identified in linear analyses and experimental studies, showing that a larger sediment heterogeneity increases the braiding indes and reduces the bars length and height. The analyses allowed identifying the applicability limits of uniform sediment and variable discharge modelling approaches.

  11. Modelling sand and gravel resources in a Late-Glacial delta system, Lough Neagh, Northern Ireland (United States)

    Roberson, Sam; Cooper, Rhys; Scanlon, Meredith; Mellett, Claire


    Sediment from glacial outwash deposited across central Ulster during deglaciation represent a major resource for aggregate and construction industries in Northern Ireland. Lough Neagh, the largest water body in the UK, acted as an accumulation basin for sediment transported by meltwater during the Late Glacial. Very little is known about the volume or type of aggregate within the Lough, despite over a half a century of sand and gravel extraction. This study presents the results of a resource survey carried out across a 47 km2 area in the northwestern part of the Lough. Multi beam echo sounding and seismic data were collected to constrain sub-bottom stratigraphy within the Lough. Bulk sediment samples from shallow boreholes and surface grabs were analysed for density and particle size to determine the type of sediment present. Volumetric data were combined with borehole logs to build a stratigraphic model of the NW corner of the Lough: lacustrine alluvium overlying a glaciolacustrine delta, underlain by glacial till. This study applies principal component analysis to log-ratio transformed particle-size distributions sampled from within the delta. Principal component scores (PCs) were interpolated within a voxel grid using ordinary kriging to derive complete particle-size distributions throughout the delta deposit. These were combined with measurements of dry density to calculate bulk sediment tonnage for British Standard cement gradings (BS 800 and BS 1200). Uncertainty in sediment tonnage (±1 sigma) was calculated by propagating kriged error variance through principal component score and log-ratio inversion.

  12. Hydrodynamics in a gravel beach and its impact on the Exxon Valdez oil (United States)

    Guo, Qiaona; Li, Hailong; Boufadel, Michel C.; Sharifi, Youness


    This paper investigated the interaction of groundwater and seawater in a tidally influenced gravel beach. Field observations of water table, pore water salinity were performed. The two-dimensional finite element model MARUN was used to simulate observed water table and salinity. Based on field observations and model calibrations, a two-layered beach structure was identified which is characterized by a high-permeability surface layer underlain by a low-permeability lower layer. The salt wedge seaward of the low tide line was almost invariant in comparison with the strong fluctuations of the salinity plume in the surface layer of the intertidal zone. The presence of the two layers prevented the presence of a freshwater discharge "tube" between the upper saline plume and salt wedge. This is in contrast with the previous works where freshwater discharge tube was observed. The tide-induced submarine groundwater discharge (SGD) was estimated at 9 m3 d-1 m-1, a large value that is probably due to the large tidal range of ˜4.8 m and the very permeable surface layer. The freshwater-seawater dynamics revealed here may provide new insights into the complexity, intensity, and time scales of mixing between fresh groundwater and seawater in tidal beaches. The simulated water table of the beach was higher than the interface between the surface layer and the lower layer, which prevented Exxon Valdez oil from penetrating into the lower layer in 1989.

  13. Low-cost multi-stage filtration enhanced by coagulation-flocculation in upflow gravel filtration

    Directory of Open Access Journals (Sweden)

    L. D. Sánchez


    Full Text Available This paper assesses the operational and design aspects of coagulation and flocculation in upflow gravel filters (CF-UGF in a multi-stage filtration (MSF plant. This study shows that CF-UGF units improve the performance of MSF considerably, when the system operates with turbidity above 30 NTU. It strongly reduces the load of particulate material before the water enters in the slow sand filters (SSF and therewith avoids short filter runs and prevents early interruption in SSF operations. The removal efficiency of turbidity in the CF-UGF with coagulant was between 85 and 96%, whereas the average efficiency without coagulant dosing was 46% (range: 21–76%. Operating with coagulant also improves the removal efficiency for total coliforms, E-coli and HPC. No reduction was observed in the microbial activity of the SSF, no obstruction of the SSF bed was demonstrated and SSF runs were maintained between 50 and 70 days for a maximum head loss of 0.70 m. The most important advantage is the flexibility of the system to operate with and without coagulant according to the influent turbidity. It was only necessary for 20% of the time to operate with the coagulant. The CF-UGF unit represented 7% of total construction costs and the O&M cost for the use of coagulant represented only 0.3%.

  14. Computational fluid dynamics and experimental tests helping to understand the gravel pack displacement in petroleum wells; Fluidodinamica computacional (CFD) e testes experimentais ajudam a compreender o fenomeno do deslocamento do gravel pack em pocos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Magalhaes, Joao Vicente Martins de; Leal, Rafael Amorim Ferreira; Martins, Andre Leibsohn; Calderon, Agostinho; Ferreira, Marcus Vinicius Duarte [Petrobras S.A., Rio de Janeiro, RJ (Brazil)], E-mails:,,,,; Simoes, Bruno; Barbosa, Diego [Halliburton, Novo Cavaleiros, Macae, RJ (Brazil)], E-mails:,


    In the petroleum exploitation and production in deep water, at the fields operated by PETROBRAS, Brazil, one of the problems frequently found is the need of elimination of sand production, having in mind that the most of those fields produce from the non consolidated sandstones. The opened well Gravel Packing is the technique most used for that task. Due to the fact of Gravel Packing operations occurs at thousand of meters below the surface, it is necessary the computational simulation for forecasting how particle deposition (Gravel) in the well occurs. So, it was used the commercial pack of fluid dynamics FLUENT 12, which calculates the fluid velocity field, coupled to another commercial pack, the EDEM, based on discrete elements that treat of particle mechanics. The coupling of the two software has shown adequate the comparison of the computational results with the experimental data shows a good adjustment. Besides, it was possible to simulate problems of well early clogging, showing that the computational simulation is strong and capable of captivating such a phenomena.

  15. Characteristics and Limitations of Submerged GPS L1 Observations (United States)

    Steiner, Ladina; Geiger, Alain


    Extensive amount of water stored in snow covers has a high impact on flood development during snow melting periods. Early assessment of these parameters in mountain environments enhance early-warning and thus prevention of major impacts. Sub-snow GNSS techniques are lately suggested to determine liquid water content, snow water equivalent or considered for avalanche rescue. This technique is affordable, flexible, and provides accurate and continuous observations independent on weather conditions. However, the characteristics of GNSS observations for applications within a snow-pack still need to be further investigated. The magnitude of the main interaction processes involved for the GPS wavelength propagating through different layers of snow, ice or water is theoretically examined. Liquid water exerts the largest influence on GPS signal propagation through a snow-pack. Therefore, we focus on determining the characteristics of GNSS observables under water. An experiment was set-up to investigate the characteristics and limitations of submerged GPS observations using a pool, a level control by communicating pipes, a geodetic and a low-cost GPS antenna, and a water level sensor. The GPS antennas were placed into the water. The water level was increased daily by a step of two millimeters up to thirty millimeters above the antenna. Based on this experiment, the signal penetration depth, satellite availability, the attenuation of signal strength and the quality of solutions are analyzed. Our experimental results show an agreement with the theoretically derived attenuation parameter and signal penetration depth. The assumption of water as the limiting parameter for GPS observations within a snow-pack can be confirmed. Higher wetness in a snow-pack leads to less transmission, higher refraction, higher attenuation and thus a decreased penetration depth as well as a reduced quality of the solutions. In consequence, GPS applications within a snow-pack are heavily impacted by

  16. Survival after submergence in the pupae of five species of blow flies (Diptera: Calliphoridae). (United States)

    Singh, D; Greenberg, B


    Survival of pupae of known ages after 1 to 5 d of submersion under water was assessed by determining the emergence of Protophormia terraenovae (Robineau-Desvoidy), Calliphora vicina (Robineau-Desvoidy), Cochliomyia macellaria (F.), Phormia regina (Meigen), and Phaenicia sericata (Meigen). Survival after 1 d of submergence was < 14% in the white puparial stage, 0-100% in pharate adults nearing eclosion, and approximately 100% in pupae between these two stages. This pattern inversely tracks O2 consumption during metamorphosis. Twenty-five percent of the pupae of three species (P. terraenovae, P. regina, and P. sericata) produced normal adults after 4 d of submersion, but none after 5 d. Among survivors, the pupation period was extended by the duration of submersion. Pupae of C. vicina were least able to withstand drowning. These data are potentially useful in estimating duration of submergence of a corpse in forensic investigations where the corpse becomes submerged after the larvae have developed and pupariated.

  17. Bioaccumulation of heavy metals by submerged macrophytes: looking for hyperaccumulators in eutrophic lakes. (United States)

    Xing, Wei; Wu, Haoping; Hao, Beibei; Huang, Wenmin; Liu, Guihua


    To directly select submerged macrophytes with high accumulation capability from the field, 24 eutrophic lakes along the middle and lower reaches of the Yangtze River were investigated in the study. These eutrophic lakes have large amounts of heavy metals in both water and sediments because of human activities. The results showed that Najas marina is a hyperaccumulator of As and Cd, Ceratophyllum demersum is a hyperaccumulator of Co, Cr, and Fe, and Vallisneria natans is a hyperaccumulator of Pb. Strong positive correlations were found between concentrations of heavy metals in tissues of submerged macrophytes, probably because of coaccumulation of heavy metals. However, for most heavy metals, no significant correlations were found between submerged macrophytes and their surrounding environments. In conclusion, N. marina, C. demersum, and V. natans are good candidate species for removing heavy metals from eutrophic lakes.

  18. Factors involved in spatiotemporal dynamics of submerged macrophytes in a Portuguese coastal lagoon under Mediterranean climate (United States)

    Antunes, Cristina; Correia, Otília; Marques da Silva, Jorge; Cruces, Anabela; Freitas, Maria da Conceição; Branquinho, Cristina


    Submerged macrophytes are key in coastal ecosystems, with important structural and functional roles. Thus, the characterization of the submerged aquatic vegetation dynamics is of prime importance for assessing the ecological status of coastal ecosystems. The main aim of this study was to assess the spatial and temporal dynamics of submerged macrophytes biomass in a temporarily open coastal lagoon in Melides, Portugal, and to evaluate the physiological performance of the dominant macrophyte in the system. This lagoon is subject to several disturbances such as the dramatic changes in water physicochemical parameters over time, since temporarily opens to the sea occur renewing the lagoon water content. Moreover it is under a Mediterranean climate with the inherently high temporal variability of precipitation and high temperatures during the summer. Our study shows that the submerged macrophyte community was dominated initially by Ruppia cirrhosa and then replaced by Potamogeton pectinatus, which showed a marked temporal and spatial pattern with extremely high values of biomass in August and in the inner part of the lagoon. The spatial and temporal biomass patterns in submerged macrophytes were mainly related with water level, salinity, pH and transparency. The physiological performance of R. cirrhosa was lower when there was greater biomass accumulation and in extremely shallow waters, whereas physiological vigor seemed to be greater at moderate temperatures and in areas with higher salinity and dissolved oxygen. The data from this study can be used to predict submerged biomass macrophyte responses to extreme water quality changes and to feed a decision support system for the best period to promote the seasonal artificial breaching of the sandy barrier.

  19. Elevation dynamics in a restored versus a submerging salt marsh in Long Island Sound (United States)

    Anisfeld, Shimon C.; Hill, Troy D.; Cahoon, Donald R.


    Accelerated sea-level rise (SLR) poses the threat of salt marsh submergence, especially in marshes that are relatively low-lying. At the same time, restoration efforts are producing new low-lying marshes, many of which are thriving and avoiding submergence. To understand the causes of these different fates, we studied two Long Island Sound marshes: one that is experiencing submergence and mudflat expansion, and one that is undergoing successful restoration. We examined sedimentation using a variety of methods, each of which captures different time periods and different aspects of marsh elevation change: surface-elevation tables, marker horizons, sediment cores, and sediment traps. We also studied marsh hydrology, productivity, respiration, nutrient content, and suspended sediment. We found that, despite the expansion of mudflat in the submerging marsh, the areas that remain vegetated have been gaining elevation at roughly the rate of SLR over the last 10 years. However, this elevation gain was only possible thanks to an increase in belowground volume, which may be a temporary response to waterlogging. In addition, accretion rates in the first half of the twentieth century were much lower than current rates, so century-scale accretion in the submerging marsh was lower than SLR. In contrast, at the restored marsh, accretion rates are now averaging about 10 mm yr−1 (several times the rate of SLR), much higher than before restoration. The main cause of the different trajectories at the two marshes appeared to be the availability of suspended sediment, which was much higher in the restored marsh. We considered and rejected alternative hypotheses, including differences in tidal flooding, plant productivity, and nutrient loading. In the submerging marsh, suspended and deposited sediment had relatively high organic content, which may be a useful indicator of sediment starvation.

  20. A Laboratory Experiment on the Evolution of a Sand Gravel Reach Under a Lack of Sediment Supply (United States)

    Orru, C.; Chavarrias, V.; Ferrara, V.; Blom, A.


    A flume experiment was conducted to examine the evolution of a sand-gravel reach under a lack of sediment supply. The experimental data are used to validate a numerical sand-gravel model. A bed composed of a bi-modal sediment mixture is installed with a uniform slope and an imposed gradual fining pattern. Initially, the sand fraction gradually increases in streamwise direction until the bed is fully composed of sand. The water discharge and downstream water level were constant, and the sediment feed rate was equal to zero. The experiment was dominated by bed load, partial transport, and a subcritical flow regime was imposed. The flow rate was such that only sand was mobile (partial transport), which led to a coarsening over the upstream reach and a gradual reduction of the sediment transport rate during the experiment. New equipment was used to measure the evolution of the grain size distribution of the bed surface during the experiment over the entire flume using image analysis. In the upstream reach we observed a gradual coarsening over time and the formation of an armour layer, which resulted in a more abrupt transition in grain size of the bed surface. Bed degradation increased in streamwise direction. This is due to the initial streamwise increase in the availability of sand in the bed. The different volume fraction content of sand in the bed allowed for the gravel to sink more in the downstream part of the upstream reach. The sand reach suffered from a larger degradation. Finally, we see one reach dominated by sand, small bedforms, and a small bed slope, and a gravel reach dominated by a larger bed slope.

  1. Oolitic limestone and marine sandstone gravel aggregate \\ud Early life concrete and aggregate freeze/thaw test for durability


    Richardson, Alan; Hemapanpairo, Kawin; Sae-Tae, Thotsaphorn; Puthipad, Nipat; Northumbria University, UK; Thammasat University, Rangsit, Thailand


    Oolitic limestone is one type of limestone which formed during the Jurassic period and can be found in large deposits in many areas of England. It can be used as coarse aggregate for concrete construction, however due to its porosity, it requires additional cement to maintain compressive strength, when compared to marine gravel (sandstone) concrete. Since freeze/thaw durability is one of the most common problems in temperate countries, this paper investigates the freeze/thaw resistance of Ool...

  2. The relative contribution of near-bed vs. intragravel horizontal transport to fine sediment accumulation processes in river gravel beds (United States)

    Casas-Mulet, Roser; Lakhanpal, Garima; Stewardson, Michael J.


    Understanding flow-sediment interactions is important for comprehending river functioning. Fine sediment accumulation processes, in particular, have key implications for ecosystem health. However, the amount of fines generated by intragravel flows and later accumulated in gravel streambeds may have been underestimated, as the hydraulic-related driving transport mechanisms in play are not clearly identified. Specifically, the relative contribution of fines from upper vs. lower sediment layers in gravel beds is not well understood. By recreating flooded and dewatered conditions in an experimental flume filled with natural sediment, we estimated such contributions by observing and collecting intragravel transported fines that were later accumulated into a void in the middle of the sediment matrix. Near-bed transport in the upper sediment layers (named Brinkman load) during flooded conditions accounted for most (90%) of the accumulated fines. Intragravel transport in the lower sediment layers (named Interstitial load) was the sole source of transport and accumulation during dewatered conditions with steeper hydraulic gradients. Interstitial load accounted for 10% of the total transport during flooded conditions. Although small, such estimations demonstrate that hydraulic-gradient transport in the lower sediment layers occurs in spite of the contradicting analytical assessments. We provide a case study to challenge the traditional approaches of assessing intragravel transport, and a useful framework to understand the origin and relative contribution of fine sediment accumulation in gravel beds. Such knowledge will be highly useful for the design of monitoring programs aiding river management, particularly in regulated rivers.

  3. Strong growth limitation of a floating plant (Lemna gibba) by the submerged macrophyte (Elodea nuttallii) under laboratory conditions

    NARCIS (Netherlands)

    Szabo, S.; Scheffer, M.; Roijackers, R.M.M.; Waluto, B.; Zambrano, L.


    1. The asymmetric competition for light and nutrients between floating and submerged aquatic plants is thought to be key in explaining why dominance by either of these groups can be stable and difficult to change. 2. Although the shading effect of floating plants on submerged plants has been well

  4. Effect of temperature and nutrients on the competition between free-floating Salvinia natans and submerged Elodea nuttallii in mesocosms

    NARCIS (Netherlands)

    Netten, J.J.C.; Arts, G.H.P.; Gylstra, R.; Nes, van E.H.; Scheffer, M.; Roijackers, R.M.M.


    In many aquatic ecosystems, free-floating plants compete with submerged plants for nutrients and light. Being on top of the water surface free-floating plants are superior competitors for light. Submerged plants can take up nutrients from the sediment and the water column, hereby reducing these

  5. Biological control of phytoplankton by the subtropical submerged macrophytes Egeria densa and Potamogeton illinoensis: a mesocosm study

    NARCIS (Netherlands)

    Vanderstukken, M.; Mazzeo, N.; Colen, W.; Declerck, S.A.J.; Muylaert, K.


    1. In temperate regions, submerged macrophytes can hamper phytoplankton blooms. Such an effect could arise directly, for instance via allelopathy, or indirectly, via competition for nutrients or the positive interaction between submerged macrophytes and zooplankton grazing. However, there is some

  6. Horicon National Wildlife Refuge, Fox River National Wildlife Refuge, Wisconsin Islands Wilderness: Green Bay and Gravel Islands National Wildlife Refuges: Annual narrative report: Calendar year 1982 (United States)

    US Fish and Wildlife Service, Department of the Interior — This annual narrative report for Horicon NWR, Fox River NWR, Wisconsin Islands Wilderness, Green Bay NWR, Gravel Islands NWR outlines Refuge accomplishments during...

  7. Horicon National Wildlife Refuge, Fox River National Wildlife Refuge, Wisconsin Islands Wilderness, Green Bay and Gravel Islands National Wildlife Refuges: Annual narrative report: Calendar year 1983 (United States)

    US Fish and Wildlife Service, Department of the Interior — This annual narrative report for Horicon NWR, Fox River NWR, Wisconsin Islands Wilderness, Green Bay NWR, and Gravel Islands NWR outlines Refuge accomplishments...

  8. Horicon National Wildlife Refuge, Fox River National Wildlife Refuge, Wisconsin Islands Wilderness, Green Bay and Gravel Islands National Wildlife Refuges: Annual narrative report: Calendar year 1987 (United States)

    US Fish and Wildlife Service, Department of the Interior — This annual narrative report for Horicon NWR, Fox River NWR, Wisconsin Islands Wilderness, Green Bay NWR, and Gravel Islands NWR outlines Refuge accomplishments...

  9. Horicon National Wildlife Refuge, Fox River National Wildlife Refuge, Wisconsin Islands Wilderness, Green Bay and Gravel Islands National Wildlife Refuges: Annual narrative report: Calendar year 1991 (United States)

    US Fish and Wildlife Service, Department of the Interior — This annual narrative report for Horicon NWR, Fox River NWR, Wisconsin Islands Wilderness, Green Bay NWR, and Gravel Islands NWR outlines Refuge accomplishments...

  10. Horicon National Wildlife Refuge, Fox River National Wildlife Refuge, Wisconsin Islands Wilderness, Green Bay and Gravel Islands National Wildlife Refuges: Annual narrative report: Calendar year 1986 (United States)

    US Fish and Wildlife Service, Department of the Interior — This annual narrative report for Horicon NWR, Fox River NWR, Wisconsin Islands Wilderness, Green Bay NWR, and Gravel Islands NWR outlines Refuge accomplishments...

  11. Horicon National Wildlife Refuge, Fox River National Wildlife Refuge, Wisconsin Islands Wilderness, Green Bay and Gravel Islands National Wildlife Refuges: Annual narrative report: Calendar year 1984 (United States)

    US Fish and Wildlife Service, Department of the Interior — This annual narrative report for Horicon NWR, Fox River NWR, Wisconsin Islands Wilderness, Green Bay NWR, and Gravel Islands NWR outlines Refuge accomplishments...

  12. An impact evaluation of a federal mine safety training regulation on injury rates among US stone, sand, and gravel mine workers: an interrupted time-series analysis

    National Research Council Canada - National Science Library

    Monforton, Celeste; Windsor, Richard


    ...) in 1999, on injury rates at stone, sand, and gravel mining operations. We applied a time-series design and analyses with quarterly counts of nonfatal injuries and employment hours from 7998 surface aggregate mines from 1995 through 2006...

  13. Horicon National Wildlife Refuge, Fox River National Wildlife Refuge, Wisconsin Islands Wilderness, Green Bay and Gravel Islands National Wildlife Refuges: Annual narrative report: Calendar year 1985 (United States)

    US Fish and Wildlife Service, Department of the Interior — This annual narrative report for Horicon NWR, Fox River NWR, Wisconsin Islands Wilderness, Green Bay NWR, and Gravel Islands NWR outlines Refuge accomplishments...

  14. Fingerprints of environmental stressors in three selected Slovenian gravel-bed rivers: geochemical and isotopic approach (United States)

    Kanduč, Tjaša; Kocman, David; Debeljak, Barbara; Mori, Nataša


    Rivers are severely impacted by a range of simultaneous processes including water pollution, flow and channel alteration, over-fishing, invasive species and climate change. Systematic studies of river water geochemistry provide important information on chemical weathering of bedrock/soil and natural anthropogenic processes that may control the dissolved chemical loads, while the isotopic studies of biological components of river systems (macrophytes, periphyton, heterotrophic biofilm, invertebrates, fish) contribute to the understanding how the system response to human impacts by means of functional response. In this contribution, insights in the fingerprints of various environmental stressors in three gravel-bed rivers (River Kamni\\vska Bistrica, River Idrijca and River Sava) in Slovenia, using geochemical and stable isotope approach are discussed. Gravel bed of all three rivers investigated is composed of carbonates and clastic rocks. The Sava and Kamni\\vska Bistrica Rivers have alpine high mountain snow-rain regime. The Idrijca River is a boundary river between the Adriatic and Black Sea catchments and has rain-snow discharge regime with torrential character. Geochemical methods (ICP-OES, IC, total alkalinity after Gran) and isotope mass - spectrometric methods (isotopic composition of dissolved inorganic carbon, particulate organic carbon and isotopic composition of carbon in carbonates) were used to evaluate biogeochemical processes in rivers. Isotopic composition of carbon and nitrogen of the moss Fontinalis antipyretica (the whole vegetative shoot) and isotopic composition of carbon of heterotrophic biofilm was also analyzed in order to better understand the fluxes and fractionation of carbon and nitrogen across trophic levels. Geochemical composition of all investigated rivers is HCO3--Ca2+-Mg2+ with different Mg2+/Ca2+ ratios as follows: around 0.33 for Kamni\\vska Bistrica and River Sava in Slovenia and above 0.75 for River Idrijca. In the Kamni

  15. Assessment of Large Wood budget in the gravel-bed Piave River: first attempt (United States)

    Tonon, Alessia; Picco, Lorenzo; Ravazzolo, Diego; Aristide Lenzi, Mario


    During the last decades, the dynamics of large wood (LW) in rivers were analyzed to consider and define the LW budget. The space-time variations of LW amount results from the differences among input (e.g. fluvial transport, lateral recruitment) and output (e.g. fluvial transport, overbank deposition, natural chronic dead) of LW along a riverine environment. Different methodologies were applied in several fluvial environments, however in large river systems characterized by complex LW dynamics, the processes are still poor quantified. Aim of this contribution is to perform a LW budget estimation over the short period, assessing the effect of an over bankfull flood (Q=1039 m3 s-1; R.I=3.5 years). The research was carried out along a 1 km-long reach (around 15 ha) located into the middle course of the large gravel-bed Piave River (North East of Italy). The LW budget has been defined considering the recruitment through bank erosion and the fluvial transport of LW into and out of the study reach. The former factor was achieved integrating field data on riparian vegetation with the monitoring of riverbanks with a Differential Global Positioning System (DGPS). The latter was obtained detecting all LW elements (diameter ≥ 0.10 m and/or length ≥ 1 m) stored along the study reach, before and after the flood. For each LW the GPS position was recorded and a numbered tag was installed with the addition of colored paint to permit a rapid post-event recovery. Preliminary results indicate that, along the study area, the floating transport of LW is one of the most significant processes able to modify the amount of LW deposited along a riverine system. In fact, considering the input of LW, the 99.4 % (102 m3 km-1) comes from upstream due to floating, whereas the 0.6% (0.17 m3 km-1) was recruited through bank erosion. Analyzing the output, 94.3% (40.26 m3 km-1) of LW was transported downstream of the study area, whereas only the 5.7 % (2.43 m3 km-1) of LW was involved in the

  16. Interactions between bar dynamics and herbaceous vegetation in gravel bed rivers: numerical simulations using BASEMENT (United States)

    Siviglia, Annunziato; Tettamanti, Stefano; Bertoldi, Walter; Toffolon, Marco; Vetsch, David; Francalanci, Simona


    A new 2D morphodynamic model for gravel bed rivers have been used to investigate the interaction between alternate bar dynamics and herbaceous vegetation. In particular, bed topography evolution has been coupled with the growth of vegetation, included as a function of the access to ground water. Numerical simulations were performed using the code BASEMENT (Vetsch et al., 2013), with the addition of a new submodel, dealing with the numerical description of the vegetation. The vegetation was allowed to grow during the dry season on exposed areas, and the vertical distribution of peak biomass was modeled as a function of the bed elevation, using a simple analytical formulation, following Marani et al. (2013). Flow resistance was divided into a component exerted by the bed and a component exerted by vegetation (Crosato and Saleh, 2010; Li and Millar, 2011); in this way we reproduced both the decrease in bed shear stress, reducing the sediment transport capacity of the flow within the plants, and the increase in hydraulic resistance, reducing flow velocity. The model was applied to a hypothetical case study, with grain size, longitudinal slope, and hydrological regime similar to that of the Magra River (Italy). A straight river reach, 125 m wide and 20 km long was simulated. Starting from an initially flat configuration, the river developed its own bar morphology, under steady formative conditions. After reaching a dynamic equilibrium, we allowed the vegetation to grow and interact with the morphodynamic evolution, reproducing a sequence of floods and growing seasons at low flow. We assumed that vegetation can be uprooted only if the bed shear stress exceeds a fixed threshold. Different scenarios were examined, varying the effect of vegetation in terms of increased resistance and threshold for uprooting (i.e. added sediment cohesion). Preliminary results confirmed that the herbaceous vegetation has a stabilizing effect on river morphology. As the density and strength of

  17. Storage and residence time of suspended sediment in gravel bars of Difficult Run, VA (United States)

    George, J.; Benthem, A.; Pizzuto, J. E.; Skalak, K.


    Reducing the export of suspended sediment is an important consideration for restoring water quality to the Chesapeake Bay, but sediment budgets for in-channel landforms are poorly constrained. We quantified fine (mapped in a 150m headwater reach at Miller Heights (bankfull width 11m; total bar volume 114 m3) and 6 gravel bars were mapped in a 160m reach downstream near Leesburg Pike (bankfull width 19m; total bar volume 210 m3). Grain size analyses of surface and subsurface samples from 2 bars at each reach indicate an average suspended sediment content of 55%, suggesting a total volume of suspended sediment stored in the mapped bars to be 178 m3, or 283000 kg, comprising 5% of the average annual suspended sediment load of the two study reaches. Estimates of the annual bedload flux at Miller Heights based on stream gaging records and the Wilcock-Crowe bedload transport equation imply that the bars are entirely reworked at least annually. Scour chains installed in 2 bars at each site (a total of 50 chains) recorded scour and fill events during the winter and spring of 2016. These data indicate that 38% of the total volume of the bars is exchanged per year, for a residence time of 2.6 ± 1.2 years, a value we interpret as the residence time of suspended sediment stored in the bars. These results are supported by mapping of topographic changes derived from structure-from-motion analyses of digital aerial imagery. Storage in alluvial bars therefore represents a significant component of the suspended sediment budget of mid-Atlantic streams.

  18. Geomorphic changes resulting from floods in reconfigured gravel-bed river channels in Colorado, USA (United States)

    Elliott, J.G.; Capesius, J.P.


    Geomorphic changes in reconfi gured reaches of three Colorado rivers in response to floods in 2005 provide a benchmark for "restoration" assessment. Sedimententrainment potential is expressed as the ratio of the shear stress from the 2 yr, 5 yr, 10 yr, and 2005 floods to the critical shear stress for sediment. Some observed response was explained by the excess of flood shear stress relative to the resisting force of the sediment. Bed-load entrainment in the Uncompahgre River and the North Fork Gunnison River, during 4 and 6 yr floods respectively, resulted in streambed scour, streambed deposition, lateral-bar accretion, and channel migration at various locations. Some constructed boulder and log structures failed because of high rates of bank erosion or bed-material deposition. The Lake Fork showed little or no net change after the 2005 flood; however, this channel had not conveyed floods greater than the 2.5 yr flood since reconfi guration. Channel slope and the 2 yr flood, a surrogate for bankfull discharge, from all three reconfi gured reaches plotted above the Leopold and Wolman channel-pattern threshold in the "braided channel" region, indicating that braiding, rather than a single-thread meandering channel, and midchannel bar formation may be the natural tendency of these gravel-bed reaches. When plotted against a total stream-power and median-sediment-size threshold for the 2 yr flood, however, the Lake Fork plotted in the "single-thread channel" region, the North Fork Gunnison plotted in the " multiplethread" region, and the Uncompahgre River plotted on the threshold. All three rivers plotted in the multiple-thread region for floods of 5 yr recurrence or greater. ?? 2009 Geological Society of America.

  19. The influence of topology on hydraulic conductivity in a sand-and-gravel aquifer (United States)

    Morin, Roger H.; LeBlanc, Denis R.; Troutman, Brent M.


    A field experiment consisting of geophysical logging and tracer testing was conducted in a single well that penetrated a sand-and-gravel aquifer at the U.S. Geological Survey Toxic Substances Hydrology research site on Cape Cod, Massachusetts. Geophysical logs and flowmeter/pumping measurements were obtained to estimate vertical profiles of porosity ϕ, hydraulic conductivity K, temperature, and bulk electrical conductivity under background, freshwater conditions. Saline-tracer fluid was then injected into the well for 2 h and its radial migration into the surrounding deposits was monitored by recording an electromagnetic-induction log every 10 min. The field data are analyzed and interpreted primarily through the use of Archie's (1942) law to investigate the role of topological factors such as pore geometry and connectivity, and grain size and packing configuration in regulating fluid flow through these coarse-grained materials. The logs reveal no significant correlation between K and ϕ, and imply that groundwater models that link these two properties may not be useful at this site. Rather, it is the distribution and connectivity of the fluid phase as defined by formation factor F, cementation index m, and tortuosity α that primarily control the hydraulic conductivity. Results show that F correlates well with K, thereby indicating that induction logs provide qualitative information on the distribution of hydraulic conductivity. A comparison of α, which incorporates porosity data, with K produces only a slightly better correlation and further emphasizes the weak influence of the bulk value of ϕ on K.

  20. A novel oxidative method for the absorption of Hg(0) from flue gas of coal fired power plants using task specific ionic liquid scrubber. (United States)

    Barnea, Zach; Sachs, Tatyana; Chidambaram, Mandan; Sasson, Yoel


    A simple continuous process is described for the removal of mercury from gas streams (such as flue gas of a coal fired power stations) using imidazolium based Task Specific Ionic Liquids [TSILs] with the general structure ([RMIM][XI(2)(-)]) where X=Cl, Br or I. The latter are formed by blending dialkylimidazolium halide salts with iodine. When applied in a gas/liquid scrubber, these salts were shown to absorb >99% of elemental mercury originally present in a gas stream in concentration of 75-400 ppb. The mercury abatement is attained by oxidating the mercury to HgI(2) which is bound as a stable IL complex ([RMIM(+)][XHgI(2)(-)]. The novel absorption system exhibits a remarkable mercury concentration factor of seven orders of magnitude. The final solution obtained contains up to 50% (w/w) mercury in the IL. Upon exposure to sodium formate, directly added to the saturated IL at 45 °C, reduced metallic mercury swiftly precipitated from the solution and could be quantitatively separated and collected. The free IL could be fully recycled. Copyright © 2012 Elsevier B.V. All rights reserved.

  1. Fluoride scrubbers for Belgian Vandersanden face-brick factories; Les briqueteries belges Vandersanden s'equipent de filtres a fluor

    Energy Technology Data Exchange (ETDEWEB)



    Complete text of publication follows: Three smoke-gas scrubbing systems including crushing plants have been installed at the different Vandersanden face-brick factories by E.I. Tec. GmbH with their commercial partner CeramicForum. The three fluoride scrubbers are of the 'cascade' type, with a specific crushing plant, to crush the waste reagent. The particular process enables Vandersanden to reintroduce their inert waste in their own clay body, avoiding expensive disposal costs. E.I. Tec. Engineering and Construction company is a leader in the technology for scrubbing smoke gases, reducing fluoride, sulphur, CO and dust, etc. within the strictest emission standards applied in U. K, U.S.A., Germany, France and BeNeLux. E.I.Tec. offers a range of dry to semi-dry, and wet scrubbing systems as well as thermal regenerative reactors to after-burn the impurities. The company entered the ceramic market two years ago via CeramicForum Sarl. Since then the market has expanded rapidly into the Netherlands, Belgium and France and is expected to grow worldwide within the next few years. (author)

  2. Nutrient removal from horticultural wastewater by benthic filamentous algae Klebsormidium sp., Stigeoclonium spp. and their communities: From laboratory flask to outdoor Algal Turf Scrubber (ATS). (United States)

    Liu, Junzhuo; Danneels, Bram; Vanormelingen, Pieter; Vyverman, Wim


    Benthic filamentous algae have evident advantages in wastewater treatment over unicellular microalgae, including the ease in harvesting and resistance to predation. To assess the potentials of benthic filamentous algae in treating horticultural wastewater under natural conditions in Belgium, three strains and their mixture with naturally wastewater-borne microalgae were cultivated in 250 ml Erlenmeyer flasks in laboratory as well as in 1 m(2) scale outdoor Algal Turf Scrubber (ATS) with different flow rates. Stigeoclonium competed well with the natural wastewater-borne microalgae and contributed to most of the biomass production both in Erlenmeyer flasks and outdoor ATS at flow rates of 2-6 L min(-1) (water velocity 3-9 cm s(-1)), while Klebsormidium was not suitable for growing in horticultural wastewater under the tested conditions. Flow rate had great effects on biomass production and nitrogen removal, while phosphorus removal was less influenced by flow rate due to other mechanisms than assimilation by algae. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Effect of heat input on dilution and heat affected zone in submerged ...

    Indian Academy of Sciences (India)

    Submerged arc welding (SAW) is a fusion joining process, known for its high deposition capabilities. This process is useful in joining thick section components used in various industries. Besides joining, SAW can also be used for surfacing applications. Heat Affected Zone (HAZ) produced within the base metal as a result of ...

  4. Effect of heat input on dilution and heat affected zone in submerged ...

    Indian Academy of Sciences (India)

    Effect of heat input on dilution and heat affected zone in submerged arc welding process. HARI OM1,∗ and SUNIL PANDEY2. 1Department of Mechanical Engineering, YMCA University of Science and. Technology, Sector 06, Faridabad 121 006, India. 2Department of Mechanical Engineering, Indian Institute of Technology ...

  5. Environmental cracking behavior of submerged arc-welded supermartensitic stainless steel weldments (United States)

    Srinivasan, P. Bala; Sharkawy, S. W.; Dietzel, W.


    Supermartensitic stainless steel welds produced by submerged are welding were assessed for their microstructure and properties. Slow strain rate tests conducted on these specimens revealed that both the parent material and the weld metals are susceptible to cracking under conditions of hydrogen (H) charging.

  6. Possibilities of Application of Carbon-Fluorine Containing Additions in Submerged-Arc Welding (United States)

    Kozyrev, N. A.; Kryukov, N. E.; Kryukov, R. E.; Igushev, V. F.; Kovalskii, I. I.


    The paper provides results of comparative analysis of the effect of carbonaceous components introduced into welding fluxes on molten metal - slag interaction. A positive influence of carbonaceous additives on gas content and mechanical properties of welds is demonstrated. Carbon and fluorine containing additives are emphasized to be promising for automatic submerged arc welding.

  7. Modification of the submerged coil to prevent microbial carryover error in thermal death studies. (United States)

    Keller, Susanne E; Shazer, Arlette G; Fleischman, Gregory J; Chirtel, Stuart; Anderson, Nathan; Larkin, John


    A submerged coil unit generates death rate data for foodborne pathogens through precise computer-controlled sequential sampling rather than the usual manually timed, labor-intensive single sampling associated with other approaches. Our work with Yersinia pseudotuberculosis and Listeria monocytogenes Scott A using the submerged coil unit indicated non-log-linear death rates with large degrees of tailing. Varying degrees of cell adhesion to the surface of the exit port resulted in carryover that was likely the primary cause of these non-log-linear kinetics. This carryover also resulted in erroneously high measured levels of thermal resistance for both organisms. To address the carryover problem, modifications were made to the exit port of the submerged coil unit to ensure continuous and uniform heat treatment. These modifications resulted in a 2-fold decrease in measured D-values for L. monocytogenes Scott A and a 10-fold decrease in measured D-values for Y. pseudotuberculosis. D-values measured with the modified machine for L. monocytogenes Scott A were similar to those found in the literature. Slight tailing in survival curves persisted with the modified method, particularly for Y. pseudotuberculosis. These results indicate that kinetic data for microbial death rates obtained using an unmodified submerged coil unit must be viewed with suspicion in light of the significant potential for carryover.

  8. Modelling of wave propagation over a submerged sand bar using SWASH

    Digital Repository Service at National Institute of Oceanography (India)

    Jishad, M.; Vu, T.T.T.; JayaKumar, S.

    A non-hydrostatic numerical model "SWASH" (Simulating WAves till SHore) is used to study the wave propagation over a submerged sand bar in a wave flume The SWASH model is calibrated and further used to validate the wave propagation for two different...

  9. Captive bubble and sessile drop surface characterization of a submerged aquatic plant, Hydrilla verticillata (United States)

    The surface energy parameters of the invasive aquatic weed, Hydrilla verticillata, were determined using contact angle measurements using two different methods. The abaxial and adaxial surfaces of the leaves and stem were characterized for the weed while submerged in water using captive air and octa...

  10. Surprising spectra of root-associated fungi in submerged aquatic plants. (United States)

    Kohout, Petr; Sýkorová, Zuzana; Ctvrtlíková, Martina; Rydlová, Jana; Suda, Jan; Vohník, Martin; Sudová, Radka


    Similarly to plants from terrestrial ecosystems, aquatic species harbour wide spectra of root-associated fungi (RAF). However, comparably less is known about fungal diversity in submerged roots. We assessed the incidence and diversity of RAF in submerged aquatic plants using microscopy, culture-dependent and culture-independent techniques. We studied RAF of five submerged isoetid species collected in four oligotrophic freshwater lakes in Norway. Levels of dark septate endophytes (DSE) colonization differed among the lakes and were positively related to the organic matter content and negatively related to pH. In total, we identified 41 fungal OTUs using culture-dependent and culture-independent techniques, belonging to Mucoromycotina, Chytridiomycota, Glomeromycota, Ascomycota as well as Basidiomycota. Sequences corresponding to aquatic hyphomycetes (e.g. Nectria lugdunensis, Tetracladium furcatum and Varicosporium elodeae) were obtained. Eight arbuscular mycorrhizal taxa belonging to the orders Archaeosporales, Diversisporales and Glomerales were also detected. However, the vast majority of the fungal species detected (e.g. Ceratobasidium sp., Cryptosporiopsis rhizophila, Leptodontidium orchidicola, and Tuber sp.) have previously been known only from roots of terrestrial plants. The abundance and phylogenetic distribution of mycorrhizal as well as nonmycorrhizal fungi in the roots of submerged plants have reshaped our views on the fungal diversity in aquatic environment. © 2011 Federation of European Microbiological Societies. Published by Blackwell Publishing Ltd. All rights reserved.


    Directory of Open Access Journals (Sweden)

    I Gede Wenten


    Full Text Available The application of membrane to replace secondary clarifier of conventional activated sludge, known as membrane bioreactor, has led to a small footprint size of treatment with excellent effluent quality. The use of MBR eliminates almost all disadvantages encountered in conventional wastewater treatment plant such as low biomass concentration and washout of fine suspended solids. However, fouling remains as a main drawback. To minimize membrane fouling, a new configuration of submerged membrane bioreactor for aerobic industrial wastewater treatment has been developed. For the new configuration, a bed of porous particle is applied to cover the submerged ends-free mounted ultrafiltration membrane. Membrane performance was assessed based on flux productivity and selectivity. By using tapioca wastewater containing high organic matter as feed solution, reasonably high and stable fluxes around 11 l/m2.h were achieved with COD removal efficiency of more than 99%. The fouling analysis also shows that the newly configured ends-free membrane bioreactor exhibits lower irreversible resistance compared with the submerged one. In addition, the performance of pilot scale system, using a membrane module  with 10 m2 effective area and reactor tank with 120 L volume, was also assessed. The flux achieved from the pilot scale system around 8 l/m2.h with COD removal of more than 99%. Hence, this study has demonstrated the feasibility of the newly configured submerged ends-free MBR at larger scale.

  12. Underwater exploration of submerged towns near Tranquebar (Tarangambadi) on Tamilnadu coast

    Digital Repository Service at National Institute of Oceanography (India)

    Rao, S.R.

    to the transgression of the sea. The foot of the medieval habitation deposit north of the temple is of great archaeological importance. Innumerable coins, mostly of copper and a few of silver, lead and gold were found indicating wreck or structure submergence....

  13. Analytical model for stage-discharge estimation in meandering compound channels with submerged flexible vegetation (United States)

    Shan, Yuqi; Liu, Xingnian; Yang, Kejun; Liu, Chao


    For overbank flows, submerged flexible vegetation on floodplains increases channel resistance and decreases channel conveyance capability. This study presents an analytical model for estimating the stage-discharge relationship in a meandering compound channel with dense, submerged, flexible vegetation on floodplains under high flow conditions. The mean velocity within a canopy was linked to the depth-averaged velocity, and a relationship between the two velocities was proposed. The governing equation was deduced in curvilinear coordinates, and the lateral shear stresses were found to be negligible, as validated by our experimental measurements in a large-scale meandering channel. Then, analytical solutions of subarea discharges and total discharge were derived by ignoring lateral shear stresses. Measurements from two flume experiments and one field study were used to verify the proposed model. The field case involved a natural river with both submerged and emergent grass on the floodplains. Good agreement between predictions and measurements indicated that the model accurately predicted subarea discharges and the stage-discharge relationships in a meandering compound channel with submerged vegetation. Finally, the predictions of this model were sensitive to the secondary flow parameters in the main channel but insensitive to those on the floodplains.

  14. Microbial community dynamics in a submerged fixed bed bioreactor during biological treatment of saline urban wastewater

    NARCIS (Netherlands)

    Cortés-Lorenzo, C.; Sipkema, D.; Rodríguez-Díaz, M.; Fuentes, S.; Juárez-Jiménez, B.; Rodelas, B.; Smidt, H.; González-López, J.


    The influence of salt (NaCl) on bacterial and archaeal communities in a submerged fixed bed bioreactor system for the treatment of urban wastewater was determined by DGGE and 454 pyrosequencing of PCR-amplified 16S ribosomal RNA gene fragments. Cluster analysis of DGGE fingerprints showed

  15. Effects of surrounding land use on metal accumulation in environments and submerged plants in subtropical ponds. (United States)

    Liu, Hui; Bu, Hongmei; Liu, Guihua; Wang, Zhixiu; Liu, Wenzhi


    Ponds are widely used as stormwater treatment facilities to retain contaminants, including metals, and to improve water quality throughout the world. However, there is still a limited understanding of the effects of surrounding land use on metal accumulation in pond environments and organisms. To address this gap, we measured the concentrations of nine metals (i.e., Al, Ba, Ca, K, Li, Mg, Na, Se, and Sr) in water, sediments, and submerged plants collected from 37 ponds with different surrounding land uses in southwestern China and assessed the metal accumulation capacity of four dominant submerged plant species. Our results showed that Al, Ca, and K concentrations in the water were above drinking water standards. In the sediments, the average concentrations of Ca and Sr were higher than the corresponding soil background values. Ceratophyllum demersum L. could accumulate more K in aboveground biomass than Myriophyllum spicatum L. and Potamogeton maackianus A. Benn. The K concentration in submerged plants was positively influenced by the corresponding metal concentration in the water and negatively influenced by water temperature. Among the nine studied metals, only the water K concentration in ponds receiving agricultural runoff was significantly higher than that for ponds receiving urban and forested runoff. This result suggests that surrounding land use types have no significant effect on metal accumulation in sediments and submerged plants in the studied ponds. A large percentage of the metals in these ponds may be derived from natural sources such as the weathering of rocks.

  16. Heavy metals in water, sediments and submerged macrophytes in ponds around the Dianchi Lake, China. (United States)

    Wang, Zhixiu; Yao, Lu; Liu, Guihua; Liu, Wenzhi


    Through retaining runoff and pollutants such as heavy metals from surrounding landscapes, ponds around a lake play an important role in mitigating the impacts of human activities on lake ecosystems. In order to determine the potential for heavy metal accumulation of submerged macrophytes, we investigated the concentrations of 10 heavy metals (i.e., As, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, and Zn) in water, sediments, and submerged macrophytes collected from 37 ponds around the Dianchi Lake in China. Our results showed that both water and sediments of these ponds were polluted by Pb. Water and sediments heavy metal concentrations in ponds received urban and agricultural runoff were not significantly higher than those in ponds received forest runoff. This result indicates that a large portion of heavy metals in these ponds may originate from atmospheric deposition and weathering of background soils. Positive relationships were found among heavy metal concentrations in submerged macrophytes, probably due to the coaccumulation of heavy metals. For most heavy metals, no significant relationships were found between submerged macrophytes and their water and sediment environments. The maximum concentrations of Cr, Fe and Ni in Ceratophyllum demersum were 4242, 16,429 and 2662mgkg(-1), respectively. The result suggests that C. demersum is a good candidate species for removing heavy metals from polluted aquatic environments. Copyright © 2014 Elsevier Inc. All rights reserved.

  17. Corrosion monitoring for underground and submerged concrete structures - examples and interpretation issues

    NARCIS (Netherlands)

    Polder, R.B.; Peelen, W.H.A.; Leegwater, G.


    Since about 1980 Corrosion Monitoring Systems have been used in many concrete structures in aggressive environmentworldwide. While these systemswork properly in aboveground environment, some questions have arisen for submerged conditions, e.g. the outer sides of tunnels, piers in seawater or

  18. A comparative study of the lipase yield by solid state and submerged ...

    African Journals Online (AJOL)



    Jan 5, 2009 ... A comparative study of lipase enzyme yields by solid state fermentation (SSF) and submerged fermentation (SmF) was performed here. Three fungal colonies were isolated from biopharmaceutical oil waste collected from “Oushadhi” (The Pharmaceutical Corporation (IM) Kerala Ltd). The pure colonies.

  19. Wave forces limit the establishment of submerged macrophytes in large shallow lakes

    NARCIS (Netherlands)

    Zuidam, van B.G.; Peeters, E.T.H.M.


    We studied the effect of waves on submerged macrophytes and hypothesized that exposure to large wave forces can hamper seedling establishment. In an indoor experiment in cylindrical mesocosms we tested whether large wave forces indeed inhibited the establishment of Chara globularis and Potamogeton

  20. Wave attenuation by submerged vegetation: combining the effect of organism traits and tidal current

    NARCIS (Netherlands)

    Paul, M.; Bouma, T.J.; Amos, C.L.


    Accurate wave height prediction along the shore plays an important role in coastal protection and management. To account for the effect of submerged vegetation in wave-attenuation models, it is important to understand how the interaction between vegetation characteristics and hydrodynamic forcing

  1. Clonal variation in the thermal response of the submerged aquatic macrophyte Potamogeton pectinatus

    NARCIS (Netherlands)

    Pilon, J.; Santamaria, L.


    Broadly distributed plants have to cope with dramatic differences across latitude in the prevailing environmental temperature. We investigated the effect of water temperature on plant morphology, biomass accumulation and oxygen-exchange for five clones of the submerged aquatic macrophyte Potamogeton

  2. Over-expression of Sub1 A, a submergence tolerance gene from ...

    African Journals Online (AJOL)

    Sub1A, an ethylene-response-factor-like (ERE-like) gene, mediates the extinguished submergence tolerance of rice. To gain further insight into the function of Sub1A in other species, we transformed tobacco plants with the gene under the control of the ubiquitin promoter. Compared to the wild-type plants, transgenic plants ...

  3. Deep water marine algal flora of the submerged banks off west coast of India

    Digital Repository Service at National Institute of Oceanography (India)

    Ambiye, V.; Untawale, A.G.

    A survey of submerged banks off India viz Cora Divh, Sessostris and Bassas de-Pedro resulted in obtaining information on the rich and diverse marine algal flora from various depths ranging from 18-70 m. A programme of onboard dredging was undertaken...

  4. A survey of estuarine submerged aquatic vegetation in the northern Gulf coast (United States)

    Carter, J.


    The status of submerged aquatic vegetation along the northern Gulf of Mexico is of concern because of its role in the ecology and economy of the coast. Recent studies by U.S. Geological Survey scientists help assess the factors that contribute to SAV distribution and health.

  5. Transient Marangoni waves due to impulsive motion of a submerged body

    CERN Document Server

    Shu, Jian-Jun


    The Oseen problem in a viscous fluid is formulated for studying the transient free-surface and Marangoni waves generated by the impulsive motion of a submerged body beneath a surface with surfactants. Wave asymptotics and wavefronts for large Reynolds numbers are obtained by employing Lighthill's two-stage scheme. The results obtained show explicitly the effects of viscosity and surfactants on Kelvin wakes.

  6. Competition between free-floating and submerged macrophytes in a future of climate change

    NARCIS (Netherlands)

    Netten, J.J.C.


    This research was about the asymmetric competition between free-floating and submerged macrophytes in shallow freshwater ecosystems. I studied the effect of climate change on the dominance of free-floating macrophytes in temperate regions. The research approach was a combination of outdoor

  7. The mechanism of improved aeration due to gas films on leaves of submerged rice. (United States)

    Verboven, Pieter; Pedersen, Ole; Ho, Quang Tri; Nicolai, Bart M; Colmer, Timothy D


    Some terrestrial wetland plants, such as rice, have super-hydrophobic leaf surfaces which retain a gas film when submerged. O2 movement through the diffusive boundary layer (DBL) of floodwater, gas film and stomata into leaf mesophyll was explored by means of a reaction-diffusion model that was solved in a three-dimensional leaf anatomy model. The anatomy and dark respiration of leaves of rice (Oryza sativa L.) were measured and used to compute O2 fluxes and partial pressure of O2 (pO2 ) in the DBL, gas film and leaf when submerged. The effects of floodwater pO2 , DBL thickness, cuticle permeability, presence of gas film and stomatal opening were explored. Under O2 -limiting conditions of the bulk water (pO2  gas film significantly increases the O2 flux into submerged leaves regardless of whether stomata are fully or partly open. With a gas film, tissue pO2 substantially increases, even for the slightest stomatal opening, but not when stomata are completely closed. The effect of gas films increases with decreasing cuticle permeability. O2 flux and tissue pO2 decrease with increasing DBL thickness. The present modelling analysis provides a mechanistic understanding of how leaf gas films facilitate O2 entry into submerged plants. © 2014 John Wiley & Sons Ltd.

  8. Acclimation of a terrestrial plant to submergence facilitates gas exchange under water

    NARCIS (Netherlands)

    Mommer, L.; Pedersen, O.; Visser, E.J.W.


    Flooding imposes stress upon terrestrial plants since it severely hampers gas exchange rates between the shoot and the environment. The resulting oxygen deficiency is considered to be the major problem for submerged plants. Oxygen microelectrode studies have, however, shown that aquatic plants

  9. A comparative study of the lipase yield by solid state and submerged ...

    African Journals Online (AJOL)

    A comparative study of lipase enzyme yields by solid state fermentation (SSF) and submerged fermentation (SmF) was performed here. Three fungal colonies were isolated from biopharmaceutical oil waste collected from “Oushadhi” (The Pharmaceutical Corporation (IM) Kerala Ltd). The pure colonies were then used as ...

  10. Impact of submerged macrophytes including charophytes on phyto- and zooplankton communities: allelopathy versus other mechanisms

    NARCIS (Netherlands)

    Van Donk, E.; Van de Bund, W.J.


    Submerged macrophytes are crucial for the stabilization of the clear water state in shallow, mesotrophic and eutrophic lakes. Especially, charophytes often play an important role because they are typically rapid colonizers and because charophyte meadows are believed to have a particularly strong

  11. Differential response to climatic variation of free-floating and submerged macrophytes in ditches

    NARCIS (Netherlands)

    Netten, J.J.C.; Zuidam, van J.P.; Kosten, S.; Peeters, E.T.H.M.


    1. Experimental studies have indicated in freshwater ecosystems that a shift in dominance from submerged to free-floating macrophytes may occur with climate change because of increased water surface temperatures and eutrophication. Field evidence is, however, rare. 2. Here, we analysed long-term (26

  12. Ethylene response factor BnERF2-like (ERF2.4 from Brassica napus L. enhances submergence tolerance and alleviates oxidative damage caused by submergence in Arabidopsis thaliana

    Directory of Open Access Journals (Sweden)

    Yanyan Lv


    Full Text Available Ethylene response factor proteins play an important role in regulating a variety of stress responses in plants, but their exact functions in submergence stress are not well understood. In this study, we isolated BnERF2.4 from Brassica napus L. to study its function in submergence tolerance. The expression of the BnERF2.4 gene in B. napus and the expression of antioxidant enzyme genes in transgenic Arabidopsis were analyzed by quantitative RT-PCR. The expression of BnERF2.4 was induced by submergence in B. napus and the overexpression of BnERF2.4 in Arabidopsis increased the level of tolerance to submergence and oxidative stress. A histochemical method detected lower levels of H2O2, O2•− and malondialdehyde (MDA in transgenic Arabidopsis. Compared to the wild type, transgenic lines also had higher soluble sugar content and higher activity of antioxidant enzymes, which helped to protect plants against the oxidative damage caused by submergence. It was concluded that BnERF2.4 increased the tolerance of plants to submergence stress and may be involved in regulating soluble sugar content and the antioxidant system in defense against submergence stress.

  13. Invasive crayfish threaten the development of submerged macrophytes in lake restoration.

    Directory of Open Access Journals (Sweden)

    Jessica E M van der Wal

    Full Text Available Submerged macrophytes enhance water transparency and aquatic biodiversity in shallow water ecosystems. Therefore, the return of submerged macrophytes is the target of many lake restoration projects. However, at present, north-western European aquatic ecosystems are increasingly invaded by omnivorous exotic crayfish. We hypothesize that invasive crayfish pose a novel constraint on the regeneration of submerged macrophytes in restored lakes and may jeopardize restoration efforts. We experimentally investigated whether the invasive crayfish (Procambarus clarkii Girard affects submerged macrophyte development in a Dutch peat lake where these crayfish are expanding rapidly. Seemingly favourable abiotic conditions for macrophyte growth existed in two 0.5 ha lake enclosures, which provided shelter and reduced turbidity, and in one lake enclosure iron was added to reduce internal nutrient loading, but macrophytes did not emerge. We transplanted three submerged macrophyte species in a full factorial exclosure experiment, where we separated the effect of crayfish from large vertebrates using different mesh sizes combined with a caging treatment stocked with crayfish only. The three transplanted macrophytes grew rapidly when protected from grazing in both lake enclosures, demonstrating that abiotic conditions for growth were suitable. Crayfish strongly reduced biomass and survival of all three macrophyte species while waterfowl and fish had no additive effects. Gut contents showed that crayfish were mostly carnivorous, but also consumed macrophytes. We show that P. clarkii strongly inhibit macrophyte development once favourable abiotic conditions for macrophyte growth are restored. Therefore, expansion of invasive crayfish poses a novel threat to the restoration of shallow water bodies in north-western Europe. Prevention of introduction and spread of crayfish is urgent, as management of invasive crayfish populations is very difficult.

  14. Crestal bone loss around submerged and nonsubmerged dental implants: A systematic review. (United States)

    Al Amri, Mohammad D


    To my knowledge, there is no systematic review of crestal bone loss (CBL) around submerged and nonsubmerged dental implants. The purpose of this review was to systematically assess CBL around submerged and nonsubmerged dental implants. The addressed focused question was, "Does crestal and subcrestal placement of dental implants influence crestal bone levels?" Databases were searched from 1986 through October 2015 using different combinations of the following keywords: crestal, sub-crestal, bone loss, dental implant, submerged, and nonsubmerged. Reference lists of potentially relevant original and review articles were hand-searched to identify any further studies. Letters to the editor, case reports, commentaries, studies on platform-switched implants, and studies published in languages other than English were excluded. In total, 13 studies (6 human and 7 animal), which were performed at universities, were included. In the human studies, the number of participants ranged from 8 to 84 individuals. The follow-up period ranged from 1 to 5 years. CBL at the test sites ranged from 0.17 mm to 0.9 mm and at control sites from 0.02 mm to 1.4 mm. Five human studies reported no significant difference in CBL around implants placed at the test and control sites. All animal studies were performed in dogs with a mean age ranging from 1 to approximately 2 years. The follow-up period ranged from 2 to 6 months. Four animal studies reported no significant difference in CBL around submerged and nonsubmerged implants. No significant difference in CBL was found around submerged and nonsubmerged dental implants. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  15. Improvement of Photosynthesis by Sub1 QTL in Rice Under Submergence: Probed by Chlorophyll Fluorescence OJIP Transients

    Directory of Open Access Journals (Sweden)

    Panda Debabrata


    Full Text Available The influence of submergence on the photosynthetic activity in rice plants either possessing or not possessing Sub1 QTL i.e. Swarna and Swarna Sub1 cultivars (cv. were evaluated under simulated complete submergence. The leaf photosynthetic rate and stomatal conductance decreased in both the cv. during the progression of submergence as compared to control plant but significant varietal differences was observed after 1 day (d of submergence. Submergence also alters the photo-system (PS II activity, as reflected in a decrease in the values of Fo, Fm and the Fv/Fm ratio and degradation of chlorophyll, more in Swarna than that of Swarna Sub1. Under complete submergence the shape of the OJIP transient also changed in rice leaves with decrease in maximal fluorescence (P=Fm intensity, resulted lowering of variable fluorescence levels. The decrease was more pronounced in Swarna compared to the Swarna Sub1 cv. Thus, Swarna Sub1 improves photosynthetic activity showing more photosynthetic rate compared to Swarna under submergence because, of less degradation of chlorophyll, higher stomatal conductance, and efficient PS II activity.

  16. Modeling wood dynamics, jam formation, and sediment storage in a gravel-bed stream (United States)

    Eaton, B. C.; Hassan, M. A.; Davidson, S. L.


    In small and intermediate sized streams, the interaction between wood and bed material transport often determines the nature of the physical habitat, which in turn influences the health of the stream's ecosystem. We present a stochastic model that can be used to simulate the effects on physical habitat of forest fires, climate change, and other environmental disturbances that alter wood recruitment. The model predicts large wood (LW) loads in a stream as well as the volume of sediment stored by the wood; while it is parameterized to describe gravel bed streams similar to a well-studied field prototype, Fishtrap Creek, British Columbia, it can be calibrated to other systems as well. In the model, LW pieces are produced and modified over time as a result of random tree-fall, LW breakage, LW movement, and piece interaction to form LW jams. Each LW piece traps a portion of the annual bed material transport entering the reach and releases the stored sediment when the LW piece is entrained and moved. The equations governing sediment storage are based on a set of flume experiments also scaled to the field prototype. The model predicts wood loads ranging from 70 m3/ha to more than 300 m3/ha, with a mean value of 178 m3/ha: both the range and the mean value are consistent with field data from streams with similar riparian forest types and climate. The model also predicts an LW jam spacing that is consistent with field data. Furthermore, our modeling results demonstrate that the high spatial and temporal variability in sediment storage, sediment transport, and channel morphology associated with LW-dominated streams occurs only when LW pieces interact and form jams. Model runs that do not include jam formation are much less variable. These results suggest that river restoration efforts using engineered LW pieces that are fixed in place and not permitted to interact will be less successful at restoring the geomorphic processes responsible for producing diverse, productive

  17. Suitability of parametric models to describe the hydraulic properties of an unsaturated coarse sand and gravel (United States)

    Mace, Andy; Rudolph, David L.; Kachanoski , R. Gary


    The performance of parametric models used to describe soil water retention (SWR) properties and predict unsaturated hydraulic conductivity (K) as a function of volumetric water content (θ) is examined using SWR and K(θ) data for coarse sand and gravel sediments. Six 70 cm long, 10 cm diameter cores of glacial outwash were instrumented at eight depths with porous cup ten-siometers and time domain reflectometry probes to measure soil water pressure head (h) and θ, respectively, for seven unsaturated and one saturated steady-state flow conditions. Forty-two θ(h) and K(θ) relationships were measured from the infiltration tests on the cores. Of the four SWR models compared in the analysis, the van Genuchten (1980) equation with parameters m and n restricted according to the Mualem (m = 1 - 1/n) criterion is best suited to describe the θ(h) relationships. The accuracy of two models that predict K(θ) using parameter values derived from the SWR models was also evaluated. The model developed by van Genuchten (1980) based on the theoretical expression of Mualem (1976) predicted K(θ) more accurately than the van Genuchten (1980) model based on the theory of Burdine (1953). A sensitivity analysis shows that more accurate predictions of K(θ) are achieved using SWR model parameters derived with residual water content (θr) specified according to independent measurements of θ at values of h where θ/h ∼ 0 rather than model-fit θr values. The accuracy of the model K(θ) function improves markedly when at least one value of unsaturated K is used to scale the K(θ) function predicted using the saturated K. The results of this investigation indicate that the hydraulic properties of coarse-grained sediments can be accurately described using the parametric models. In addition, data collection efforts should focus on measuring at least one value of unsaturated hydraulic conductivity and as complete a set of SWR data as possible, particularly in the dry range.

  18. Manipulating riparian vegetation, large wood, and discharge in a gravel-cobble bed stream: channel response (United States)

    McDowell, P. F.


    change and hydraulic factors is not supported. With healthy riparian vegetation and log structures, this reach is relatively resistant to change, yet it continues to have an active and mobile gravel-cobble bed, even in years with modest floods.

  19. Bank erosion and large wood recruitment along a gravel bed river

    Directory of Open Access Journals (Sweden)

    Lorenzo Picco


    Full Text Available Riverine environments can be very dynamic and complex systems, particularly because of the interaction between active channel and riparian land during flood events of different magnitude. In recent years increasing attention has been paid to large wood (LW, focusing on its role and impact along riverine systems and fluvial landscapes. This research aims to analyze the characteristics of LW recruitment as a consequence of a flood event along a reach of a gravel-bed river. The study was conducted on a 3 km-long reach located in the middle course of the Piave River (north-eastern Italian Alps. A 20 m-wide buffer zone was considered along the floodplains and islands. Every standing tree in this buffer with diameter ≥0.10 m was measured manually (diameter breast height; height, whereas shrubs were not considered. The most common species in the study area are: Populus sp., Salix sp., Alnus sp., Carpinus sp., Fraxinus sp., Pinus sylvestris and Robinia pseudoacacia. An over bankfull flood (Q=1329 m3s–1; recurrence interval=6 years in November 2014 caused erosions along the floodplain (15,565.5 m2, pioneer islands (25.2 m2 and building islands (2085.6 m2, recruiting 690 trees. Four of these trees were recruited from the pioneer islands (0.16 tree m–2, 79 from building islands (0.04 tree m–2 and 607 from floodplains (0.04 tree m–2. Accurate dendrometric measurements were used to define the input volume of LW from the floodplains (86.25 m3, pioneer islands (0.14 m3 and building islands (6.62 m3. The maximum distance traveled by LW recruited from the floodplain, pioneer and building islands was 8927, 1021 and 3727 m, respectively. Statistical analysis showed no significant relationship between the displacement and LW characteristics considered (diameter, length, volume, density. These results demonstrate that the recruitment and subsequent transport of LW is a complex mechanism that requires further study. To better characterize these mechanisms

  20. Field testing of three bedload samplers' efficiency in a gravel-bed river, Spitsbergen (United States)

    Rachlewicz, Grzegorz; Zwoliński, Zbigniew; Kociuba, Waldemar; Stawska, Monika


    A comparative study of the three bedload traps was accomplished to determine the effectiveness differences between the devices. The research was carried out in two transverse sections of the proglacial, gravel-bedded Scott River (SW Svalbard) using three devices to perform direct measurements of bedload transport in the river channels. Several samplers are used for field measurements, but none of them has gained widespread acceptance as a standard so far. The paper compares transport rates collected in three bedload samplers that differ in structure and functionality: i) a portable Helley-Smith, pressure-difference bedload sampler (H-S), ii) an anchored River Bedload Trap (RBT), and iii) the portable sampler used by the Polish Hydrological Services (PIHM type C). All three samplers are constructed using the same components: a frame made of thin stainless steel sheet and a nylon bag with the same (2 mm) mesh size (except PIHM). Measurements were conducted within three consecutive days in two cross sections, in the same vertical profiles and at the same time (at intervals of 30 and 60 min). Measurements of bedload transport and water velocity were performed simultaneously. In order to determine the effectiveness and representativeness of short-term measurements using particular devices, the masses of the samples were converted into a specific rate of bedload transport and compared to the results of long-term continuous measurement (24 h measurement cycle). The results confirm that both specific transport indicators and the mass of the samples collected by the tested devices show a significant variation. Generally, the highest mass and specific transport indicators were obtained using the H-S sampler. The RBT produced moderate transport rates, while the PIHM sampler gave the lowest rates. The bedload transport rate in a profile estimated on the short-term measurements was compared to results of the continuous measurements conducted in the same cross sections. In the 7

  1. Microbial community variation and functions to excess sludge reduction in a novel gravel contact oxidation reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lin Shanshan; Jin, Y.; Fu, L. [School of Urban and Environmental Science, Northeast Normal University, Changchun (China); Quan, C. [Jilin University, College of medicine, Changchun (China); Yang, Y.S., E-mail: [Cardiff University, School of Earth and Ocean Sciences, Cardiff CF10 3YE (United Kingdom)


    Excess biomass produced within the degradation processes of organic pollutants is creating environmental challenges. The gravel contact oxidation reactor (GCOR) filled with crushed stone globular aggregates as carriers, has been demonstrated capable of reducing the excess sludge effectively in some pilot and small-scale engineering studies. In order to evaluate the variation and structure of the microbial community and their functions to excess sludge reduction in GCOR, a conventional activated sludge reactor (ASR) was studied as a comparison. The 16S rDNA library of the universal bacteria was constructed, Shannon's diversity index (H) and Species evenness (E) were calculated with distance-based operational taxonomic unit and richness (DOTUR) for microbial diversity. Real-time quantity PCR and optical microscope were used for absolute bacterial DNA concentration and eukarya identification, respectively. Meanwhile, the suspended solid index in GCOR and ASR was detected for assessing the excess sludge production. The results indicated that the most abundant bacteria in GCOR were those related to the {beta}-Proteobacteria group, then {gamma}-Proteobacteria and to Cytophaga-Flexibacter-Bacteriode (CFB). In the ASR samples major bacteria were in the closest match with {gamma}-Proteobacteria, then {beta}-Proteobacteria and CFB. Shannon's index (H) was higher (3.41) for diversity of bacteria extracted from the carrier samples in GCOR than that (2.71) from the sludge sample in ASR. Species evenness (E) for the isolates from GCOR and ASR samples was 0.97 and 0.96, respectively. Comparison of the universal bacteria population in GCOR and ASR shows that the total bacterial DNA concentration on the GCOR carriers were 8.98 x 10{sup 5} {mu}g/{mu}l, twice that in ASR of 4.67 x 10{sup 5} {mu}g/{mu}l under normal operation of two reactors. But the MLSS in GCOR was only 4.5 mg/L, 25 times less than that in ASR of 115.4 mg/L. The most representative eukarya were protozoa

  2. Thermal plume transport from sand and gravel pits - Potential thermal impacts on cool water streams (United States)

    Markle, Jeff M.; Schincariol, Robert A.


    SummaryWe investigated the potential thermal impacts from below-water-table aggregate extraction on a cool-water stream supporting Brook trout ( Salvelinus fontinalis) and cool-water macroinvertebrates. We monitored thermal plumes emanating from an aggregate pit through an unconfined, glacial-outwash aquifer. Our objectives were to complete a detailed assessment to quantify the persistence of thermal plumes in the subsurface, and establish a framework for guiding these investigations as the growing demand for aggregate increases pressures to pursue extraction in ecologically sensitive areas. During a 10-year period, we measured ground and surface water temperatures in an outwash aquifer and cool-water stream, including two periods of intensive monitoring (22 months and 2.5 years) focusing on plume movement from one aggregate pit. We quantified the aquifer hydraulic conductivity K at the laboratory and field scale, and characterized the effective thermal conductivity λ at an unprecedented level of detail. The mean K's from the multi-scale tests span two-orders of magnitude, 1.8 × 10 -4 to 1.7 × 10 -2 m s -1, and are related to the test support volume. The saturated λ has a mean of 2.42 W m -1 K -1, ranges from 2.14 to 2.69 W m -1 K -1, and is correlated to stratigraphic units (gravel, sand, and till). The annual temperature amplitude in the pit is 10 °C above up gradient ground water, and our results show that alternating warm and cool plumes persist in the aquifer for 11 months and migrate up to 250 m down gradient. The observed plume velocity (1.2 m d -1) lags the ground water velocity (2.8 m d -1) due to thermal retardation. Furthermore, hydraulic conductivity is shown to vary with the scale of the test and ground water velocities estimated from pumping tests may overestimate thermal plume velocities. While we focused on plume migration, our results demonstrate that assessing impacts on the aquatic community requires an integrated, multi-disciplinary study

  3. Total Dissolved Gas Monitoring in Chum Salmon Spawning Gravels Below Bonneville Dam

    Energy Technology Data Exchange (ETDEWEB)

    Arntzen, Evan V.; Geist, David R.; Panther, Jennifer L.; Dawley, Earl


    At the request of the U.S. Army Corps of Engineers (Portland District), Pacific Northwest National Laboratory (PNNL) conducted research to determine whether total dissolved gas concentrations are elevated in chum salmon redds during spring spill operations at Bonneville Dam. The study involved monitoring the total dissolved gas levels at egg pocket depth and in the river at two chum salmon spawning locations downstream from Bonneville Dam. Dissolved atmospheric gas supersaturation generated by spill from Bonneville Dam may diminish survival of chum (Oncorhynchus keta) salmon when sac fry are still present in the gravel downstream from Bonneville Dam. However, no previous work has been conducted to determine whether total dissolved gas (TDG) levels are elevated during spring spill operations within incubation habitats. The guidance used by hydropower system managers to provide protection for pre-emergent chum salmon fry has been to limit TDG to 105% after allowing for depth compensation. A previous literature review completed in early 2006 shows that TDG levels as low as 103% have been documented to cause mortality in sac fry. Our study measured TDG in the incubation environment to evaluate whether these levels were exceeded during spring spill operations. Total dissolved gas levels were measured within chum salmon spawning areas near Ives Island and Multnomah Falls on the Columbia River. Water quality sensors screened at egg pocket depth and to the river were installed at both sites. At each location, we also measured dissolved oxygen, temperature, specific conductance, and water depth to assist with the interpretation of TDG results. Total dissolved gas was depth-compensated to determine when levels were high enough to potentially affect sac fry. This report provides detailed descriptions of the two study sites downstream of Bonneville Dam, as well as the equipment and procedures employed to monitor the TDG levels at the study sites. Results of the monitoring at

  4. Landforms Affect Gravel-Cobble Bed River Hydraulics at Different Spatial Scales and Discharges (United States)

    Gonzalez, R. L.; Pasternack, G. B.; Wyrick, J. R.; Johnson, T.


    River hydraulics are generally modeled to predict inundation extents, assess aquatic species habitat, understand sediment transport regimes, and describe geomorphic processes. These metrics are in turn used to guide floodplain development, instream flow requirements, river rehabilitation projects, reservoir management, and further research. Consequently, the emergence of 2D hydraulic modeling is usually a means to some end other than characterizing and discussing the fundamental aspects of fluvial hydraulics. The purpose of this study was to ascertain the role of different components of multi-scalar, heterogeneous fluvial landforms in controlling the spatial pattern of river hydraulics at 28 different flows ranging from 0.06 to 22 times bankfull discharge. The testbed data for the study consisted of 1-m resolution rasters of depth, velocity, and Shields stress over 37.5 km of the regulated gravel-cobble bed Lower Yuba River (LYR) located in the Sacramento River Valley of California. Each variable was analyzed for its discharge-dependent power function (i.e. at-a-station hydraulic geometry) at segment, reach, and morphologic spatial scales, with data stratified by 8 reaches, 4 inundation zones, two vegetation regions, and 31 morphological units. This was done using all points, not just at cross-sections. At each spatial scale, trend lines were statistically compared to determine if they were differentiated. Mean velocity and Shields stress as a function of discharge vary by reach, including several velocity and Shields stress reversals. The range of mean velocity and Shields stress between reaches increases with discharge. There are several reach-scale velocity reversals that take place among the reaches, especially at 0.3 and 2 times bankfull discharge, whereas there is only one major Shields stress reversal at 6 times bankfull discharge. Stage-dependent cross sectional area and substrate size govern these interactions. The two most downstream reaches had the

  5. Effect of HRT on nitrogen removal in a coupled HRP and unplanted subsurface flow gravel bed constructed wetland (United States)

    Mayo, A. W.; Mutamba, J.

    This paper discusses the effect of hydraulic retention time (HRT) on nitrogen removal in a coupled high rate pond (HRP) and a gravel bed subsurface constructed wetland (SSCW) wastewater treatment plant. A pilot plant consisting of a high rate pond (HRT) coupled to an unplanted gravel bed subsurface constructed wetland (SSCW) was used to investigate nitrogen removal from domestic wastewater at the University of Dar es Salaam. The influent, which is predominantly of domestic origin, was drawn from the facultative pond unit of the university’s waste stabilisation pond system. The pilot plant’s HRP unit, which was 0.6 m deep, was designed to nitrify the influent while SSCW unit, which was filled to 10 cm above water level with 19-mm diameter aggregates, was predominantly anoxic and promoted denitrification. The study was conducted at two different operational settings. In Phase 1, both the HRP and the SSCW units had a retention time of 5 days. During Phase 2, the hydraulic retention time in HRP was increased to 8 days while the retention time of the SSCW unit was maintained at 5 days. Samples were collected daily for laboratory analysis of influent and effluent wastewater quality. All experiments were conducted in accordance with Standard Methods. The results showed that improved nitrogen removal occurred with increase in hydraulic time of the HRP unit. In Phase 1 an average nitrogen removal of 33% was achieved while removal efficiency improved to 43% in Phase 2. It was also revealed that the HRP can effectively be used to promote nitrification and the unplanted gravel bed subsurface constructed wetland can be used as a denitrifying unit.

  6. Costs of swimming measured at optimum speed: scale effects, differences between swimming styles, taxonomic groups and submerged and surface swimming. (United States)

    Videler, J J; Nolet, B A


    1. Data on swimming energy expenditure of 30 submerged and nine surface swimmers, covering different swimming styles and taxonomic groups, are selected from the literature. 2. The costs of transport at the optimum speed are compared and related to body mass and Re numbers. 3. Fish and turtles use relatively less and most surface swimmers slightly more energy than the other submerged swimmers; man and mink are poorly adapted to swimming. 4. The metabolic rate in W at optimum speed is approximately equal to the body mass in kg for fish and turtles and three times the mass figure for the other submerged swimmers.

  7. Monitoring of dust emission on gravel roads: Development of a mobile methodology and examination of horizontal diffusion (United States)

    Edvardsson, Karin; Magnusson, Rolf

    Traffic-generated fugitive dust on gravel roads impairs visibility and deposits on the adjacent environment. Particulate matter smaller than 10 μm in diameter (PM 10) is also associated with human health problems. Dust emission strength depends on the composition of granular material, road moisture, relative humidity, local climate (precipitation, wind velocity, etc.), and vehicle characteristics. The objectives of this study were to develop a reliable and rapid mobile methodology to measure dust concentrations on gravel roads, evaluate the precision and repeatability of the methodology and correspondence with the currently used visual assessment technique. Downwind horizontal diffusion was studied to evaluate the risk of exceeding the maximum allowed particulate matter concentration in ambient air near gravel roads according to European Council Directive [European Council Directive 1999/30/EC of 22 April 1999 relating to limit values for sulphur dioxide, nitrogen dioxide and oxides of nitrogen, particulate matter and lead in ambient air. Official Journal of the European Communities. L163/41.]. A TSI DustTrak Aerosol Monitor was mounted on an estate car travelling along test sections treated with various dust suppressants. Measured PM 10 concentrations were compared to visual assessments performed at the same time. Airborne particles were collected in filters mounted behind the vehicle to compare the whole dust fraction with the PM 10 concentration. For measuring the horizontal diffusion, DustTraks were placed at various distances downwind of a dusty road section. The mobile methodology was vehicle and speed dependent but not driver dependent with pre-specified driving behaviours. A high linear correlation between PM 10 of different vehicles makes relative measurements of dust concentrations possible. The methodology gives continuous data series, mobility, and easy handling and provides fast, reliable and inexpensive measurements for estimating road conditions to

  8. EAARL-B Submerged Topography–Saint Croix, U.S. Virgin Islands, 2014 (United States)

    U.S. Geological Survey, Department of the Interior — ASCII XYZ point cloud data for a portion of the submerged environs of Saint Croix, U.S. Virgin Islands, was produced from remotely sensed, geographically referenced...

  9. EAARL-B Submerged Topography–—Saint Thomas, U.S. Virgin Islands, 2014 (United States)

    U.S. Geological Survey, Department of the Interior — ASCII XYZ point cloud data for a portion of the submerged environs of Saint Thomas, U.S. Virgin Islands, was produced from remotely sensed, geographically referenced...

  10. Seed weight and germination behavior of the submerged plant Potamogeton pectinatus in the arid zone of northwest China

    National Research Council Canada - National Science Library

    Li, Zhongqiang; Lu, Wei; Yang, Lei; Kong, Xianghong; Deng, Xuwei


    .... This study examined within‐species variation in seed weight and germination attributes and the effects of environmental factors on seed traits of the submerged plant P otamogeton pectinatus in the arid zone of northwest China...

  11. Medium selection for exopolysaccharide and biomass production in submerged cultures of culinary-medicinal mushrooms from Turkey

    NARCIS (Netherlands)

    Kizilcik, M.; Yamaç, M.; Griensven, van L.J.L.D.


    The present study investigates the exopolysaccharide (EPS) and biomass production of 18 strains of 15 species of culinary-medicinal higher Basidiomycetes in submerged culture under four different media. Gloeophyllum abietinum and Schizophyllum commune produced the highest EPS and biomass

  12. Surviving floods: leaf gas films improve O2 and CO2 exchange, root aeration, and growth of completely submerged rice

    DEFF Research Database (Denmark)

    Pedersen, Ole; Rich, Sarah Meghan; Colmer, Timothy David


    that the improved gas exchange was not caused by differences in diffusive boundary layers adjacent to submerged leaves with or without gas films; instead, reduced resistance to gas exchange was probably due to the enlarged water–gas interface (cf. aquatic insects). When gas films were removed artificially......When completely submerged, the leaves of some species retain a surface gas film. Leaf gas films on submerged plants have recently been termed 'plant plastrons', analogous with the plastrons of aquatic insects. In aquatic insects, surface gas layers (i.e. plastrons) enlarge the gas–water interface...... to promote O2 uptake when under water; however, the function of leaf gas films has rarely been considered. The present study demonstrates that gas films on leaves of completely submerged rice facilitate entry of O2 from floodwaters when in darkness and CO2 entry when in light. O2 microprofiles showed...

  13. EAARL-B coastal topography: Fire Island, New York, pre-Hurricane Sandy, 2012: seamless (bare earth and submerged) (United States)

    Wright, C. Wayne; Kranenburg, Christine J.; Klipp, Emily S.; Troche, Rodolfo J.; Fredericks, Alexandra M.; Masessa, Melanie L.; Nagle, David B.


    These remotely sensed, geographically referenced elevation measurements of lidar-derived seamless (bare-earth and submerged) topography datasets were produced by the U.S. Geological Survey (USGS), St. Petersburg Coastal and Marine Science Center, St. Petersburg, Florida.

  14. Voxel modelling of sands and gravels of Pleistocene Rhine and Meuse deposits in Flanders (Belgium) (United States)

    van Haren, Tom; Dirix, Katrijn; De Koninck, Roel


    Voxel modelling or 3D volume modelling of Quaternary raw materials is VITO's next step in the geological layer modelling of the Flanders and Brussels Capital Region in Belgium (G3D - Matthijs et al., 2013). The aim is to schematise deposits as voxels ('volumetric pixels') that represent lithological information on a grid in three-dimensional space (25 x 25 x 0.5 m). A new voxel model on Pleistocene Meuse and Rhine sands and gravels will be illustrated succeeding a voxel model on loess resources (van Haren et al., 2016). The model methodology is based on a geological 'skeleton' extracted from the regional geological layer model of Flanders. This framework holds the 3D interpolated lithological information of 5.000 boreholes. First a check on quality and spatial location filtered out significant and usable lithological information. Subsequently a manual geological interpretation was performed to analyse stratigraphical arrangement and identify the raw materials of interest. Finally, a workflow was developed that automatically encodes and classifies the borehole descriptions in a standardized manner. This workflow was implemented by combining Microsoft Access® and ArcMap® and is able to convert borehole descriptions into specific geological parameters. An analysis of the conversed lithological data prior to interpolation improves the understanding of the spatial distribution, to fine tune the modelling process and to know the limitations of the data. The converted lithological data were 3D interpolated in Voxler using IDW and resulted in a model containing 52 million voxels. It gives an overview on the regional distribution and thickness variation of interesting Pleistocene aggregates of Meuse and Rhine. Much effort has been put in setting up a database structure in Microsoft Access® and Microsoft SQL Server® in order to arrange and analyse the lithological information, link the voxel model with the geological layer model and handle and analyse the resulting

  15. Coherent flow structures in a depth-limited flow over a gravel surface: The influence of surface roughness (United States)

    Hardy, Richard J.; Best, James L.; Lane, Stuart N.; Carbonneau, Patrice E.


    Turbulent flows moving over a gravel bed develop large-scale, macroturbulent flow structures that are initiated at anchor clasts in the bed and grow and dissipate as they move upward through the flow depth. This paper extends previous research in which we investigated the influence of the Reynolds number on coherent flow structures generated over a gravel bed by assessing the importance of effective bed roughness. Here, we report on flume experiments in which flows over beds of decreasing surface roughness have been quantified through the application of digital particle imaging velocimetry, which allows study of the downstream and vertical components of velocity over the entire flow field. These results indicate that as the effective roughness increases (1) the visual distinctiveness of the coherent flow structures becomes more defined throughout the flow depth, (2) the upstream angle of slope of the coherent flow structure increases, and (3) the reduction in streamwise flow velocity and turbulence intensity toward the upstream side of the structure becomes greater. Applying standard scaling laws, these structures appear shear-generated and form through a combination of both wake flapping and the reattachment of localized shear layers associated with flow separation around individual topographic protrusions. As the effective protrusion decreases, the scale of these coherent flow structures also decreases.

  16. A 2D hydrodynamic-sedimentological model for gravel-bed rivers. Part I: theory and validation

    Directory of Open Access Journals (Sweden)

    Gabriel Kaless


    Full Text Available This paper presents a novel 2D-depth average model especially developed for gravel-bed rivers, named Lican-Leufú (Lican=pebble and Leufu=river, in Mapuche’s language, the native inhabitants of Central Patagonia, Argentina. The model consists of three components: a hydrodynamic, a sedimentological, and a morphological model. The flow of water is described by the depth-averaged Reynolds equations for unsteady, free-surface, shallow water flows. It includes the standard k-e model for turbulence closure. Sediment transport can be divided in different size classes (sand-gravel mixture and the equilibrium approach is used for Exner’s equation. The amour layer is also included in the structure of the model and the surface grain size distribution is also allowed to evolve. The model simulates bank slides that enable channel widening. Models predictions were tested against a flume experiment where a static armour layer was developed under conditions of sediment starvations and general good agreements were found: the model predicted adequately the sediment transport, grain size of transported material, final armour grain size distribution and bed elevation.

  17. Assessment Approach for Identifying Compatibility of Restoration Projects with Geomorphic and Flooding Processes in Gravel Bed Rivers (United States)

    DeVries, Paul; Aldrich, Robert


    A critical requirement for a successful river restoration project in a dynamic gravel bed river is that it be compatible with natural hydraulic and sediment transport processes operating at the reach scale. The potential for failure is greater at locations where the influence of natural processes is inconsistent with intended project function and performance. We present an approach using practical GIS, hydrologic, hydraulic, and sediment transport analyses to identify locations where specific restoration project types have the greatest likelihood of working as intended because their function and design are matched with flooding and morphologic processes. The key premise is to identify whether a specific river analysis segment (length ~1-10 bankfull widths) within a longer reach is geomorphically active or inactive in the context of vertical and lateral stabilities, and hydrologically active for floodplain connectivity. Analyses involve empirical channel geometry relations, aerial photographic time series, LiDAR data, HEC-RAS hydraulic modeling, and a time-integrated sediment transport budget to evaluate trapping efficiency within each segment. The analysis segments are defined by HEC-RAS model cross sections. The results have been used effectively to identify feasible projects in a variety of alluvial gravel bed river reaches with lengths between 11 and 80 km and 2-year flood magnitudes between ~350 and 1330 m3/s. Projects constructed based on the results have all performed as planned. In addition, the results provide key criteria for formulating erosion and flood management plans.

  18. Temporal stability and variability of soil-water content in a gravel-mulched field in northwestern China (United States)

    Zhao, Wenju; Cui, Zhen; Zhang, Jiyi; Jin, Jian


    Characterizing the spatiotemporal variability of soil-water content (SWC) is of paramount importance in many scientific fields and operational applications. We present a case study of the temporal stability and variability of SWC in a gravel-mulched field, a form of mulching that has been widely used by farmers on the loessial area of China for over 300 years, using Spearman correlation coefficients, frequency distributions and an index of temporal stability. SWC was measured weekly from May to August 2013 in the 0-10, 10-20, 20-30 and 30-50 cm layers. SWC was more variable in the surface soil, due to several environmental factors, and the variability gradually decreased with depth. A large sample size was needed for estimating the mean SWC of the field under dry conditions. High Spearman correlation coefficients between the SWCs measured on different sampling campaigns indicated a high temporal stability. The stability of the SWC spatial patterns over time and along the soil profile allowed us to identify a location representative of the field-mean SWC, with high coefficients of determination ranging between 0.8564 and 0.9325. The large-scale monitoring of SWC from few observations is thus feasible, which will aid the management of soil moisture in gravel-mulched fields in arid regions.

  19. Statistical Evaluation of the Relationship Between Gravel Road Dustiness and Environmental Conditions Using Molasses Solution for Reducing Dustiness

    Directory of Open Access Journals (Sweden)

    Jolita Bradulienė


    Full Text Available   The problem of gravel road dustiness is quite acute. In order to minimize harmful environmental components and to conduct dust reduction tests, molasses materials were chosen. Using the molasses materials of a new generation (solution Safecote in the Lithuanian market, the obtained results of dustiness have reflected a reduction in particulate matter in the air. During the experiment, gravel road pavement was treated with different degrees of concentration (10%, 20%, 30% in solution “Safecote” at a driving speed of 30 km/h. Dustiness was measured at different distances from the road (0 m, 1 m, 2 m, 3 m. The undertaken study showed that the concentrations of particulate matter varied under changing weather conditions (air temperature, humidity, wind speed, atmospheric pressure. The statistical analysis of the received data has revealed that dustiness weakly correlates with temperature (correlation coefficient ranged from 0.12 to 0.67 moving from the road, the correlation coefficient of moisture is negative, a larger distance from the road increases inverse correlation (the correlation coefficient ranges from –0.02 to –0.85, negative correlation decreases moving from the road at a speed of the wind (from –0.72 to –0.06 and pressure correlation remains volatile (from –0.44 to 0.44. Article in Lithuanian 

  20. Performance comparison of constructed wetlands with gravel- and rice husk-based media for phenol and nitrogen removal. (United States)

    Tee, H C; Seng, C E; Noor, A Md; Lim, P E


    This study aims to compare the performance of planted and unplanted constructed wetlands with gravel- and raw rice husk-based media for phenol and nitrogen removal. Four laboratory-scale horizontal subsurface-flow constructed wetland units, two of which planted with cattail (Typha latifolia) were operated outdoors. The units were operated at a nominal hydraulic retention time of 7 days and fed with domestic wastewater spiked with phenol concentration at 300 mg/L for 74 days and then at 500 mg/L for 198 days. The results show that planted wetland units performed better than the unplanted ones in the removal and mineralization of phenol. This was explained by the creation of more micro-aerobic zones in the root zone of the wetland plants which allow a faster rate of phenol biodegradation, and the phenol uptake by plants. The better performance of the rice husk-based planted wetland compared to that of the gravel-based planted wetland in phenol removal could be explained by the observation that more rhizomes were established in the rice husk-based wetland unit thus creating more micro-aerobic zones for phenol degradation. The role of rice husk as an adsorbent in phenol removal was considered not of importance.

  1. A semianalytical three-dimensional process-based model for hyporheic nitrogen dynamics in gravel bed rivers (United States)

    Marzadri, Alessandra; Tonina, Daniele; Bellin, Alberto


    We present a three-dimensional semianalytical process-based model of dissolved oxygen and dissolved inorganic nitrogen (DIN) transformation within the hyporheic zone of gravel bed rivers. Oxygen and multispecies solute transport is solved within a Lagrangian framework with transformation of DIN species modeled by linearized Monod's kinetics, with temperature-dependent reaction rate coefficients derived from field experiments. Our solutions, which are obtained under the assumptions of sediments with uniform hydraulic properties and negligible local dispersion, highlight the importance of morphological characteristics of the streambed on DIN transformations within the hyporheic zone. By means of this model we explore the effects of streambed topography and relative abundance of ammonium and nitrate in stream waters on the reactive nitrogen cycle in the hyporheic zone of gravel bed rivers with a pool and riffle morphology. Our model shows complex concentration dynamics within the hyporheic zone that may act as a source or a sink of nitrogen depending on the residence time distribution, which can be parameterized in terms of streambed morphology, and the ratio between the in-stream concentrations of ammonium and nitrate. Application of the model to seven natural streams shows good agreement between predicted and measured nitrous oxide emissions from their hyporheic zone.

  2. Geospatial organization of fluvial landforms in a gravel-cobble river: Beyond the riffle-pool couplet (United States)

    Wyrick, J. R.; Pasternack, G. B.


    Morphological units (MU) are landforms with distinct local form-process associations at ~ 1-10 channel widths scale that may be the fundamental building blocks describing the geomorphic structure of a river. Past research has disproportionately focused on the two MUs of pool and riffle, conjecturing that they are the central linked couplet in the process-form association. The goal of this study was to delineate and map spatially explicit fluvial landforms in two-dimensional planview within a gravel-cobble bed river using two-dimensional hydrodynamic delineation and then to statistically examine MU geospatial patterns for indicators of deterministic geomorphic control. This procedure is not discharge-dependent like mesohabitat methods, but gets at the geometry of underlying landforms. Statistical testing confirmed that eight delineated in-channel MU types comprise a complex and diverse channel morphology in which pools and riffles are not directly coupled. Specifically, gravel-cobble river channels (1) exhibit nonrandom spatial organization of their longitudinally and laterally variable landform morphology; (2) consist of a variety of MU types, not just pools and riffles; and (3) show distinct MU collocations and avoidances, with riffles linked to chutes and runs, while pools are linked to slackwaters and glides. Planview MU delineation with two-dimensional hydrodynamic modeling provides a 'bottom-up' approach to understanding and linking channel morphology with ecosystem services and geomorphic processes and is being used to guide river management and rehabilitation strategies.

  3. XRD and DTA Analysis of Developed Agglomerated Fluxes for Submerged Arc Welding

    Directory of Open Access Journals (Sweden)

    Ajay Kumar


    Full Text Available A unique study of structural and chemical analysis of crystalline phases in developed agglomerated fluxes was carried out. Thirty-two fluxes were developed by using a mixture of oxides, halides, carbonates, silicates, and ferroalloys for submerged arc welding. The present paper focuses on only ten (out of thirty-two fluxes which were analyzed by X-ray diffraction (XRD to know the different types of oxides formed and changed in oxidation number of metallic centers after sintering process at around 850∘C. To know the effect of temperature over phase transformation and melting of different compounds, differential thermal analysis (DTA was carried out from 1000 to 1400∘C. This study aims to know the quantity of ions present (percentage and melting behavior of developed agglomerated fluxes for submerged arc welding process.

  4. Two-flow simulation of the natural light field within a canopy of submerged aquatic plants (United States)

    Ackleson, S. G.; Klemas, V.


    A two-flow model is developed to simulate a light field composed of both collimated and diffuse irradiance within natural waters containing a canopy of bottom-adhering plants. To account for the effects of submerging a canopy, the transmittance and reflectance terms associated with each plant structure (leaves, stems, fruiting bodies, etc.) are expressed as functions of the ratio of the refractive index of the plant material to the refractive index of the surrounding media and the internal transmittance of the plant stucture. Algebraic solutions to the model are shown to yield plausible physical explanations for unanticipated variations in volume reflectance spectra. The effect of bottom reflectance on the near-bottom light field is also investigated. These indicate that within light-limited submerged aquatic plant canopies, substrate reflectance may play an important role in determining the amount of light available to the plants and, therefore, canopy productivity.

  5. Acclimation of a terrestrial plant to submergence facilitates gas exchange under water

    DEFF Research Database (Denmark)

    Mommer, L.; Pedersen, O.; Visser, E. J. W.


    Flooding imposes stress upon terrestrial plants since it severely hampers gas exchange rates between the shoot and the environment. The resulting oxygen deficiency is considered to be the major problem for submerged plants. Oxygen microelectrode studies have, however, shown that aquatic plants...... maintain relatively high internal oxygen pressures under water, and even may release oxygen via the roots into the sediment, also in dark. Based on these results, we challenge the dogma that oxygen pressures in submerged terrestrial plants immediately drop to levels at which aerobic respiration is impaired....... The present study demonstrates that the internal oxygen pressure in the petioles of Rumex palustris plants under water is indeed well above the critical oxygen pressure for aerobic respiration, provided that the air-saturated water is not completely stagnant. The beneficial effect of shoot acclimation...

  6. Wave energy absorption by a submerged air bag connected to a rigid float

    DEFF Research Database (Denmark)

    Kurniawan, Adi; Chaplin, J. R.; Hann, M. R.


    A new wave energy device features a submerged ballasted air bag connected at the top to a rigid float. Under wave action, the bag expands and contracts, creating a reciprocating air flow through a turbine between the bag and another volume housed within the float. Laboratory measurements are gene......A new wave energy device features a submerged ballasted air bag connected at the top to a rigid float. Under wave action, the bag expands and contracts, creating a reciprocating air flow through a turbine between the bag and another volume housed within the float. Laboratory measurements...... are generally in good agreement with numerical predictions. Both show that the trajectory of possible combinations of pressure and elevation at which the device is in static equilibrium takes the shape of an S. This means that statically the device can have three different draughts, and correspondingly three...

  7. [Applied study of the submerged macrophytes bed-immobilized bacteria in drinking water restoration]. (United States)

    Chen, Qi-Chun; Li, Zheng-Kui; Wang, Yi-Chao; Wu, Kai; Fan, Nian-Wen


    The effect of submerged macrophytes bed-immobilized bacteria technology which applied in drinking water restoration was studied. Ammonifying bacteria, nitrobacteria, nitrosobacteria and denitrifying bacteria which isolated from Taihu Labe was immobilized to the porous carries, combined with the submerged macrophytes bed technology, we applied the new equipment in water restoration of gonghu bay, this equipment has good ability to resist storm, the denitrifying bacteria number increased from 5.4 x 10(2)-2.7 x 10(3) to 3.9 x 10(5)-9.1 x 10(5), N2O flux of experimental plot was 3-24 microg x (m2 x h)(-1), it's more than the contrast group obviously, TN concentration reduced 19% - 74%, while NO3- concentration reduced 24% -81% after the equipment running a period of time; The experimental data of 120 days showed that this technology is suitable for drinking water restoration, as it can control eutrophication.

  8. Ultrasound imaging measurement of submerged topography in the muddy water physical model (United States)

    Xiao, Xiongwu; Guo, Bingxuan; Li, Deren; Zou, Xianjian; Zhang, Peng; liu, Jian-chen; Zang, Yu-fu


    The real-time, accurate measurement of submerged topography is vital for the analysis of riverbed erosion and deposition. This paper describes a novel method of measuring submerged topography in the B-scan image obtained using an ultrasound imaging device. Results show the distribution of gray values in the image has a process of mutation. This mutation process can be used to adaptively track the topographic lines between riverbed and water, based on the continuity of topography in the horizontal direction. The extracted topographic lines, of one pixel width, are processed by a wavelet filtering method. Compared with the actual topography, the measurement accuracy is within 1 mm. It is suitable for the real-time measurement and analysis of all current model topographies with the advantage of good self-adaptation. In particular, it is visible and intuitive for muddy water in the movable-bed model experiment.

  9. Onshore and nearshore explorations along the Maharashtra Coast: With a view to locating ancient ports and submerged sites

    Digital Repository Service at National Institute of Oceanography (India)

    Tripati, S.; Gaur, A.S.

    and Nearshore Explorations along the Maharashtra Coast: with a View to Locating Ancient Ports and Submerged Sites Sila Tripati and A.S. Gaur Marine Archaeology Centre National Institute of Oceanography Dona Paula Goa 403 004 Abstract Coastal explorations... migrations by exploring and excavating defunct and submerged ports as well as sunken ships. A systematic attempt has been made by the National Institute of Oceanography (NIO) to explore and study the ancient ports and their locations all along the coast...

  10. Contribution of seedling vigour and anoxia/hypoxia-responsive genes to submergence tolerance in Vietnamese lowland rice (Oryza sativa L.

    Directory of Open Access Journals (Sweden)

    Hien Thi Thu Vu


    Full Text Available A direct-seeded rice cultivation system has been widely adopted in Asian countries. Optimum germination and vigorous seedling growth under submergence are key traits for the practice of direct seeding. We studied the post-germination seedling vigour in Vietnamese lowland rice accessions based on three bio-parameters, shoot elongation growth under five-day submergence in water-filled test-tubes, seedling recovery rate five days after transferring submerged seedlings to pots with soil and seedling survival rate 21 days after sowing seeds in nursery beds and immediate incubation under submergence. A large diversity was found in seedling vigour thus estimated among the accessions. Significantly high correlations were observed among all three bio-parameters, verifying the contribution of seedling vigour to the manifestation of submergence tolerance at this critical stage of rice development. To examine the roles of anoxia/hypoxia-responsive genes, the expression of 17 candidate genes was studied by reverse transcription polymerase chain reaction (RT-PCR and compared between selected vigorous and non-vigorous groups of accessions. Transcripts of all but two genes showed marked accumulation in submerged seedlings. No differences, however, were found between the two contrasting groups. The observed common and coordinate expression of anoxia/hypoxia-induced genes suggests that they might assume roles in attaining baseline tolerance against submergence stress. It was also suggested that some unknown genetic factors are operating in determining cultivar/genotype-specific levels of submergence tolerance as assessed by post-germination seedling vigour.

  11. A new mechanism of macrophyte mitigation: how submerged plants reduce malathion's acute toxicity to aquatic animals. (United States)

    Brogan, William R; Relyea, Rick A


    A growing body of evidence suggests that aquatic plants can mitigate the toxicity of insecticides to sensitive aquatic animals. The current paradigm is that this ability is driven primarily by insecticide sorption to plant tissues, especially for hydrophobic compounds. However, recent work shows that submerged plants can strongly mitigate the toxicity of the relatively hydrophilic insecticide malathion, despite the fact that this compound exhibits a slow sorption rate to plants. To examine this disparity, we tested the hypothesis that the mitigating effect of submerged plants on malathion's toxicity is driven primarily by the increased water pH from plant photosynthesis causing the hydrolysis of malathion, rather than by sorption. To do this, we compared zooplankton (Daphnia magna) survival across five environmentally relevant malathion concentrations (0, 1, 4, 6, or 36 μg L(-1)) in test containers where we chemically manipulated water pH in the absence of plants or added the submerged plant (Elodea canadensis) but manipulated plant photosynthetic activity via shading or no shading. We discovered that malathion was equally lethal to Daphnia at all concentrations tested when photosynthetically inactive (i.e. shaded) plants were present (pH at time of dosing=7.8) or when pH was chemically decreased (pH=7.7). In contrast, when photosynthetically active (i.e. unshaded) plants were present (pH=9.8) or when pH was chemically increased (pH=9.5), the effects of 4 and 6 μg L(-1) of malathion on Daphnia were mitigated strongly and to an equal degree. These results demonstrate that the mitigating effect of submerged plants on malathion's toxicity can be explained entirely by a mechanism of photosynthesizing plants causing an increase in water pH, resulting in rapid malathion hydrolysis. Our findings suggest that current ecotoxicological models and phytoremediation strategies may be overlooking a critical mechanism for mitigating pesticides. Copyright © 2014 Elsevier Ltd

  12. Geothermal Investigations of California Submerged Lands and Spherical Flow in Naturally Fractured Reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Northup, William F.; Everitts, D.J.; Eaton, C.F.; Welday, E.E.; Martin, Roger C.; Ershaghi, Iraj; Wilde, P.; Oldson, J.C.; Case, C.W.


    A large portion of California State-owned land is the tidal and submerged land along the coastline and around the islands that extends seaward for three geographical miles. Other large areas of State-owned lands form the beds of lakes and navigable rivers. Some evidence, such as the proximity of hot springs, indicates there may be important geothermal potential on these lands. The purpose of this project is to develop methods, tools, and interpretive techniques to explore for and evaluate geothermal resources on submerged lands. Presently, the state of the art is primitive because there has been little interest or effort in assessing the resource potential of submerged lands, and the limited work carried out thus far has been for scientific purposes. There has been a moderate amount of water temperature measuring for oceanographic or limnologic studies and fairly reliable techniques exist. There have been limited measurements of the temperature, thermal gradient, and heat flow in bottom sediment of the ocean area off California and from the lakes. Probably less than a dozen data points exist for State-owned land. This work was done using large equipment, such as piston corers with outrigger-mounted thermistors arrayed along the core barrels. To achieve penetration, such equipment requires heavy weights, strong cable, heavy duty winches, large crews and oceanographic research-type vessels or large barges, and this entails considerable expenses and logistical problems. Clearly, many hundreds, or thousands of data points are required for a remotely reliable evaluation of the resources. The first problem is to assess existing methods and develop others that will enable economical and efficient exploration for geothermal resources on submerged lands.

  13. Submergence rice cultivation in southern Bangladesh: farmers opinion and adaptations practices

    Directory of Open Access Journals (Sweden)

    AKM Abdul Ahad Biswas


    Full Text Available Rice productivity in coastal Bangladesh is lower than the national average and total coastal area is considered to be submergence-prone and higher vulnerable in July to January cropping season. The selected study areas are Kalapara and Patuakhali Sadar Upazila that are too vulnerable to agriculture practices. Field survey was conducted during 01st June to 30th July, 2015 to investigate the impact of submergence on Aman rice cultivation (ARC, existing adopted local adaptation practices with impacts and options to address the submergence problem. Primary data was collected through Focus Group Discussion (FGD, Individual Interview and Key Informant Interview methods and secondary data was collected from different secondary sources. A well-structured pretested questionnaire schedule was developed keeping in mind the objectives and variables under this study. After cyclone SIDR and AILA devastation, the rate of traditional ARC is decreasing every year and in 2015 it was 26.51%. Recently farmers have adopted new cropping practices and strategies like modern ARC in Aman season as single crop; Boro-Aus-Aman season as triple crop and Aus-Aman season as double crop are practicing. Approximately all farmers have adopted to grow stress tolerant rice varieties (STRV; farmer’s curiosities to familiar with and to have the STRV are encouraging. Farmers were fully adopted BRRIdhan52 rice cultivation with positive perceptions of higher yield and lower production cost. Therefore it can be concluded that the intensity of adoption of adaptation and mitigation measures are significantly influenced positively by the STRV yield capability; farmer’s participation in intervention programs; livelihood diversification; frequency of extension personnel contact; submergence and inundation characteristics; tolerance attributes of STRV and availability of STRV cultivation information.International Journal of Environment Vol.4(4 2015: 100-113

  14. Inulinase Production by a Mexican Semi-Desert Xerophylic Penicillium citrinum Strain under Submerged Culture


    Adriana C. Flores-Gallegos; Jesús Morlett-Chávez; Aguilar, Cristóbal N.; Raúl Rodríguez-Herrera


    The aim of the study was to produce inulinase under submerged culture (SmC) by a xerophylic fungal strain isolated from the Mexican semi-dessert and to verify its potential as an industrial inulinase producer. This enzyme can be obtained from microorganisms that live in close association with inulin plant store tissues. Inulin is a widespread plant polyfructan that serves as a storage polysaccharide in several plants and its depolymerization involves the action of inulinase. Inulinases are cl...

  15. Modern morphological engineering techniques for improving productivity of filamentous fungi in submerged cultures


    Antecka, Anna; Bizukojc, Marcin; Ledakowicz, Stanislaw


    Morphological engineering techniques have recently gained popularity as they are used for increasing the productivity of a variety of metabolites and enzymes in fungi growing in submerged cultures. Their action is mainly associated with the changes they evoke in fungal morphology. Traditional morphological engineering approaches include manipulation of spore concentration, pH-shifting and mechanical stress exerted by stirring and aeration. As the traditional methods proved to be insufficient,...

  16. A filtration model applied to submerged anaerobic MBRs (SAnMBRs)


    Robles Martínez, Ángel; Ruano García, María Victoria; Ribes Bertomeu, José; SECO TORRECILLAS, AURORA; Ferrer, J.


    The aim of this study was to develop a model able to correctly reproduce the filtration process of submerged anaerobic MBRs (SAnMBRs). The proposed model was calibrated and validated in a SAnMBR demonstration plant fitted with industrial-scale hollow-fibre membranes. Three suspended components were contemplated in the model: total solids concentration; dry mass of cake on the membrane surface; and dry mass of irreversible fouling on the membrane surface. The model addressed the following phys...

  17. Mathematical modelling of filtration in submerged anaerobic MBRs (SAnMBRs): long-term validation


    Robles Martínez, Ángel; Ruano García, María Victoria; Ribes Bertomeu, José; SECO TORRECILLAS, AURORA; Ferrer, J.


    The aim of this study was the long-term validation of a model capable of reproducing the filtration process occurring in a submerged anaerobic membrane bioreactor (SAnMBR) system. The proposed model was validated using data obtained horn a SAnMBR demonstration plant fitted with industrial-scale hollow-fibre membranes. The validation was carried out using both lightly and heavily fouled membranes operating at different bulk concentrations, gas sparging intensities and transmembrane fluxes. Acr...

  18. Design methodology for submerged anaerobic membrane bioreactors (AnMBR): A case study


    Ferrer, J.; Pretel, R.; Durán Pinzón, Freddy; Giménez, JB; Robles Martínez, Ángel; Ruano García, María Victoria; Serralta Sevilla, Joaquín; Ribes Bertomeu, José; SECO TORRECILLAS, AURORA


    The main objective of this study is to propose guidelines for designing submerged anaerobic MBR (AnMBR) technology for municipal wastewater treatment. The design methodology was devised on the basis of simulation and experimental results from an AnMBR plant featuring industrial-scale hollow-fibre membranes. The proposed methodology aims to minimise both capital expenditure and operating expenses, and the key parameters considered were: hydraulic retention time, solids retention ti...

  19. Corncob hydrolysate, an efficient substrate for Monascus pigment production through submerged fermentation. (United States)

    Zhou, Zhongxin; Yin, Zheng; Hu, Xiaoqing


    Monascus pigment has traditionally been produced by the fermentation of Monascus using rice powder or glucose as a culture substrate. Submerged fermentation can produce stable Monascus pigment yield and control the accumulation of the by-product, citrinin, which can then be more easily removed. To reduce the cost of Monascus submerged fermentation, the feasibility of corncob hydrolysate as an alternative substrate was investigated. Results showed that, when compared with a conventional glucose medium, the corncob hydrolysate medium produced an equivalent pigment yield without stimulating citrinin accumulation. Furthermore, the corncob hydrolysate medium and cultivation conditions were optimized to enhance pigment production and decrease citrinin synthesis. When Monascus sp. was cultured under dark conditions in the presence of caprylic acid, pigment production was increased to 25.8 ± 0.8 UA500 /mL, which was higher than that achieved in a glucose medium (24.0 ± 0.9 UA500 /mL), and those obtained in previously reported Monascus submerged fermentations using the same yield unit; on the other hand, citrinin accumulation was decreased to 26.2 ± 1.9 µg/L, which was significantly lower than that generated in the glucose control (44.3 ± 2.2 µg/L) and in those previously reported fermentations. Thus, corncob hydrolysate was proved to be an efficient alternative substrate for Monascus pigment production through submerged fermentation, which showed significant advantages over a conventional glucose substrate. © 2014 International Union of Biochemistry and Molecular Biology, Inc.

  20. Natural variation of submergence tolerance among Arabidopsis thaliana accessions

    DEFF Research Database (Denmark)

    Vashisht, D.; Hesselink, A.; Pierik, R.


    in the dark. Survival curves were plotted to estimate median lethal times as a measure of tolerance. Flooding-associated survival parameters, such as root and shoot oxygen content, initial carbohydrate content and petiole elongation under water, were also measured. • There was a significant variation....... • Arabidopsis accessions show considerable variation in the ability to tolerate complete submergence, making it a good species in which to identify and characterize genes and to study mechanisms that contribute to survival under water....