WorldWideScience

Sample records for submaximal statokinetic load

  1. Racing Skiers and Swimmers’ Heart Electric Field during Ventricular Depolarization at Recovery Period after Moderate and Submaximal Physical Load

    Directory of Open Access Journals (Sweden)

    Svetlana V. Strelnikova

    2013-01-01

    Full Text Available The article presents the results of cardioelectrotopographic investigation of racing skiers and swimmers’ heart electric activity during ventricular depolarization at recovery period after moderate and submaximal physical load. Changes in ventricular depolarization time and ventricular depolarization phases ratio due to longer duration of the first and second cardioelectric potential inversions on the chest surface in racing skiers and less duration of the depolarization initial phase in swimmers were detected after moderate and submaximal load

  2. Kinematic and Electromyographic Activity Changes during Back Squat with Submaximal and Maximal Loading

    Directory of Open Access Journals (Sweden)

    Hasan U. Yavuz

    2017-01-01

    Full Text Available The aim of this study was to investigate the possible kinematic and muscular activity changes with maximal loading during squat maneuver. Fourteen healthy male individuals, who were experienced at performing squats, participated in this study. Each subject performed squats with 80%, 90%, and 100% of the previously established 1 repetition maximum (1RM. Electromyographic (EMG activities were measured for the vastus lateralis, vastus medialis, rectus femoris, semitendinosus, biceps femoris, gluteus maximus, and erector spinae by using an 8-channel dual-mode portable EMG and physiological signal data acquisition system (Myomonitor IV, Delsys Inc., Boston, MA, USA. Kinematical data were analyzed by using saSuite 2D kinematical analysis program. Data were analyzed with repeated measures analysis of variance (p<0.05. Overall muscle activities increased with increasing loads, but significant increases were seen only for vastus medialis and gluteus maximus during 90% and 100% of 1RM compared to 80% while there was no significant difference between 90% and 100% for any muscle. The movement pattern in the hip joint changed with an increase in forward lean during maximal loading. Results may suggest that maximal loading during squat may not be necessary for focusing on knee extensor improvement and may increase the lumbar injury risk.

  3. A Systematic Review of Submaximal Cycle Tests to Predict, Monitor, and Optimize Cycling Performance.

    Science.gov (United States)

    Capostagno, Benoit; Lambert, Michael I; Lamberts, Robert P

    2016-09-01

    Finding the optimal balance between high training loads and recovery is a constant challenge for cyclists and their coaches. Monitoring improvements in performance and levels of fatigue is recommended to correctly adjust training to ensure optimal adaptation. However, many performance tests require a maximal or exhaustive effort, which reduces their real-world application. The purpose of this review was to investigate the development and use of submaximal cycling tests that can be used to predict and monitor cycling performance and training status. Twelve studies met the inclusion criteria, and 3 separate submaximal cycling tests were identified from within those 12. Submaximal variables including gross mechanical efficiency, oxygen uptake (VO2), heart rate, lactate, predicted time to exhaustion (pTE), rating of perceived exertion (RPE), power output, and heart-rate recovery (HRR) were the components of the 3 tests. pTE, submaximal power output, RPE, and HRR appear to have the most value for monitoring improvements in performance and indicate a state of fatigue. This literature review shows that several submaximal cycle tests have been developed over the last decade with the aim to predict, monitor, and optimize cycling performance. To be able to conduct a submaximal test on a regular basis, the test needs to be short in duration and as noninvasive as possible. In addition, a test should capture multiple variables and use multivariate analyses to interpret the submaximal outcomes correctly and alter training prescription if needed.

  4. The effect of submaximal exercise on fibrinolysis.

    Science.gov (United States)

    Fras, Zlatko; Keber, Dusan; Chandler, Wayne L

    2004-04-01

    We studied the relationship between sustained submaximal exercise, increased tissue plasminogen activator (t-PA) levels and decreased hepatic clearance of t-PA. Six healthy male volunteers exercised for 35 min while receiving constant rate infusions of either saline or two different doses of recombinant t-PA for 90 min (40 min before, 35 min during and 15 min after exercise). Liver blood flow was estimated simultaneously by constant rate indocyanine green infusion. Since t-PA is cleared rapidly by the liver in direct proportion to liver blood flow, it was expected that a significant decrease in liver blood flow during sustained submaximal exercise would be associated with a proportional increase in plasma t-PA. During submaximal exercise with a saline (placebo) infusion, steady-state t-PA antigen increased from a resting baseline of 6.3 +/- 3.1 to 15.1 +/- 5.1 ng/ml; with a 20 microg/min t-PA infusion, t-PA antigen increased from 33 +/- 12 to 84 +/- 25 ng/ml during exercise; and with a 40 microg/min t-PA infusion, t-PA antigen increased from 77 +/- 38 to 166 +/- 42 ng/ml during exercise. During submaximal exercise, liver blood flow fell on average 71, 68 and 70%, respectively, during the three procedures, while calculated t-PA clearance decreased on average 59, 59 and 53%. t-PA concentration versus time curves, displayed in proportional units, were similar. The comparable relative increases in endogenous and exogenous t-PA with simultaneous proportional decreases in liver blood flow suggests that diminished hepatic t-PA clearance is the major cause of increased t-PA concentration and blood fibrinolytic activity enhancement during sustained submaximal exercise.

  5. Validated Predictions of Metabolic Energy Consumption for Submaximal Effort Movement.

    Directory of Open Access Journals (Sweden)

    George A Tsianos

    2016-06-01

    Full Text Available Physical performance emerges from complex interactions among many physiological systems that are largely driven by the metabolic energy demanded. Quantifying metabolic demand is an essential step for revealing the many mechanisms of physical performance decrement, but accurate predictive models do not exist. The goal of this study was to investigate if a recently developed model of muscle energetics and force could be extended to reproduce the kinematics, kinetics, and metabolic demand of submaximal effort movement. Upright dynamic knee extension against various levels of ergometer load was simulated. Task energetics were estimated by combining the model of muscle contraction with validated models of lower limb musculotendon paths and segment dynamics. A genetic algorithm was used to compute the muscle excitations that reproduced the movement with the lowest energetic cost, which was determined to be an appropriate criterion for this task. Model predictions of oxygen uptake rate (VO2 were well within experimental variability for the range over which the model parameters were confidently known. The model's accurate estimates of metabolic demand make it useful for assessing the likelihood and severity of physical performance decrement for a given task as well as investigating underlying physiologic mechanisms.

  6. F-door spaces and F-submaximal spaces

    Directory of Open Access Journals (Sweden)

    Lobna Dridi

    2013-04-01

    Full Text Available Submaximal spaces and door spaces play an enigmatic role in topology. In this paper, reinforcing this role, we are concerned with reaching two main goals: The first one is to characterize topological spaces X such that F(X is a submaximal space (resp., door space for some covariant functor Ff rom the category Top to itself. T0, and FH functors are completely studied. Secondly, our interest is directed towards the characterization of maps f given by a flow (X, f in the category Set, such that (X,P(f is submaximal (resp., door where P(f is a topology on X whose closed sets are exactly the f-invariant sets.

  7. Assessment of muscle endurance of the knee extensor muscles in adolescents with spastic cerebral palsy using a submaximal repetitions-to-fatigue protocol.

    Science.gov (United States)

    Eken, Maaike M; Dallmeijer, Annet J; Doorenbosch, Caroline A; Dekkers, Hurnet; Becher, Jules G; Houdijk, Han

    2014-10-01

    To compare muscle endurance in adolescents with spastic cerebral palsy (CP) with typically developing (TD) peers using a submaximal repetitions-to-fatigue (RTF) protocol. Cross sectional. Human motion laboratory. Adolescents with spastic CP (n=16; Gross Motor Function Classification System levels I or II) and TD adolescents (n=18) within the age range of 12 to 19 years old. Not applicable. Each participant performed 3 RTF tests at different submaximal loads, ranging from 50% to 90% of their maximal voluntary knee extension torque. The relation between the number of repetitions (repetition maximum [RM]) and imposed submaximal relative (percent of maximal voluntary torque [%MVT]) and absolute (Nm/kg) torque was quantified. To compare adolescents with CP with TD adolescents, a mixed linear model was used to construct load endurance curves. Surface electromyography of quadriceps muscles was measured to assess changes in normalized amplitude and median frequency (MF) as physiological indicators of muscle fatigue. Adolescents with CP showed a larger decrease in %MVT per RM than TD adolescents (Pmuscles in all tests for both groups. Electromyographic MF decreased significantly (Pmuscle fatigue were reached. Adolescents with CP show slightly lower muscle endurance compared with TD adolescents on a submaximal RTF protocol, which is in contrast with earlier findings in a maximal voluntary fatigue protocol. Accordingly, adolescents with CP have a reduced capacity to endure activities at similar relative loads compared with TD adolescents. Copyright © 2014 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

  8. Recruitment of single muscle fibers during submaximal cycling exercise

    NARCIS (Netherlands)

    Altenburg, T.M.; Degens, H.; van Mechelen, W.; Sargeant, A.J.; de Haan, A.

    2007-01-01

    In literature, an inconsistency exists in the submaximal exercise intensity at which type II fibers are activated. In the present study, the recruitment of type I and II fibers was investigated from the very beginning and throughout a 45-min cycle exercise at 75% of the maximal oxygen uptake, which

  9. Differential contributions of ankle plantarflexors during submaximal isometric muscle action

    DEFF Research Database (Denmark)

    Masood, Tahir; Bojsen-Møller, Jens; Kalliokoski, Kari K

    2014-01-01

    The objective of this study was to investigate the relative contributions of superficial and deep ankle plantarflexors during repetitive submaximal isometric contractions using surface electromyography (SEMG) and positron emission tomography (PET). Myoelectric signals were obtained from twelve....... The findings of this study provide valuable reference for studies where individual muscle contributions are estimated using models and simulations....

  10. Myocardial oxygen consumption at rest and during submaximal ...

    African Journals Online (AJOL)

    olayemitoyin

    2008-11-26

    Nov 26, 2008 ... Department of Physiology, JSS Medical College, Constituent College of JSS University, Mysore – 570015, ... determine the effect of increased adiposity on myocardial oxygen consumption at rest and during submaximal exercise in ... during exercise suggesting higher hemodynamic stress to the heart.

  11. An Investigation into Submaximal Endurance in Children with Motor ...

    African Journals Online (AJOL)

    This study investigated the submaximal endurance levels of children with motor difficulties, using the six-minute walk test (6MWT). A prospective, cross-sectional study was conducted. Forty-eight children between ages seven and ten years were enrolled. They came from similar socio-economic backgrounds and attended ...

  12. Myocardial oxygen consumption at rest and during submaximal ...

    African Journals Online (AJOL)

    Overweight and obesity are major risk factors for cardiovascular diseases. The objective of this study was to determine the effect of increased adiposity on myocardial oxygen consumption at rest and during submaximal exercise in young adults. The study consisted of 85 young adults (18-22years) grouped into 3 based on ...

  13. Influence of menstrual phase on ventilatory response to submaximal ...

    African Journals Online (AJOL)

    Objectives. To determine whether an increase in respiratory drive, due to elevated progesterone and oestrogen concentration during various menstrual phases, persists throughout prolonged submaximal exercise and potentially contributes to fatigue. Furthermore, to determine whether the difference in the ventilatory ...

  14. Myocardial oxygen consumption at rest and during submaximal ...

    African Journals Online (AJOL)

    olayemitoyin

    2008-11-26

    Nov 26, 2008 ... and myocardial fatty acid utilization has been showed to decrease after weight loss from gastric bypass surgery or diet in obese persons (Fei ho et al., 1995,). During submaximal exercise and immediately after exercise, all three groups showed an increase in. RPP. The percentage increase in RPP was.

  15. Haemodynamic changes induced by submaximal exercise before a dive and its consequences on bubble formation

    Science.gov (United States)

    Blatteau, Jean‐Eric; Boussuges, Alain; Gempp, Emmanuel; Pontier, Jean‐Michel; Castagna, Olivier; Robinet, Claude; Galland, Francois‐Michel; Bourdon, Lionel

    2007-01-01

    Objectives To evaluate the effects of a submaximal exercise performed 2 h before a simulated dive on bubble formation and to observe the haemodynamic changes and their influence on bubble formation. Participants and methods 16 trained divers were compressed in a hyperbaric chamber to 400 kPa for 30 min and decompressed at a rate of 100 kPa/min with a 9 min stop at 130 kPa (French Navy MN90 procedure). Each diver performed two dives 3 days apart, one without exercise and one with exercise before the dive. All participants performed a 40 min constant‐load submaximal and calibrated exercise, which consisted of outdoor running 2 h before the dive. Circulating bubbles were detected with a precordial Doppler at 30, 60 and 90 min after surfacing. Haemodynamic changes were evaluated with Doppler echocardiography. Results A single bout of strenuous exercise 2 h before a simulated dive significantly reduced circulating bubbles. Post‐exercise hypotension (PEH) was observed after exercise with reductions in diastolic and mean blood pressure (DBP and MBP), but total peripheral resistance was unchanged. Stroke volume was reduced, whereas cardiac output was unchanged. Simulated diving caused a similar reduction in cardiac output independent of pre‐dive exercise, suggesting that pre‐dive exercise only changed DBP and MBP caused by reduced stroke volume. Conclusion A single bout of strenuous exercise 2 h before a dive significantly reduced the number of bubbles in the right heart of divers and protected them from decompression sickness. Declining stroke volume and moderate dehydration induced by a pre‐dive exercise might influence inert gas load and bubble formation. PMID:17138641

  16. The effect of menstruation on chosen physiological and biochemical reactions caused by the physical effort with the submaximal intensity

    Directory of Open Access Journals (Sweden)

    P Zieliński

    2003-03-01

    Full Text Available The aim of this work was to determine the influence of the menstruation phase on changes of respective indicators of the gas exchange and on biochemical parameters of blood during physical efforts with the sub-maximal intensity. Fifteen female students of the Academy of Physical Education took part in the study. Girls were aged from 19 to 22 years old and did not practice sports. The effort tests were conducted in the follicular and luteal phase of two succeeding menstrual cycles. As far the aerobic capacity determination is concerned, one cyclo-ergometric test with graded effort was conducted and it was performed till the “refusal”. It allowed to mark a threshold (TDMA and a maximal level of physiological and biochemical indicators. Basing on the results of the graded test individual loads were determined for every next effort trial (repeated 4 times in every phase of the two succeeding menstrual cycles. The aim of this trial was to evaluate the reaction of women’s constitution on work with the sub-maximal intensity. The above trial consisted on two 10 min efforts divided with the 2 min pause (the first effort with the intensity of 80% of the TDMA threshold, second with the intensity bigger about 30-40% of difference between TDMA and a maximal load established by the graded test. The research did not reveal statistically significant differentiation as considering effort changes of basic physiological and biochemical indicators, determining reaction of women’s organisms on work with the sub- and over- threshold intensity (TDMA. It showed that menstruation has not significant effect on the level of changes of analysed parameters caused by the physical effort with the sub-maximal intensity.

  17. The validity of submaximal ratings of perceived exertion to predict one repetition maximum.

    Science.gov (United States)

    Eston, Roger; Evans, Harrison James Llewelyn

    2009-01-01

    The One Repetition Maximum (1-RM) test is commonly used to assess strength. However, direct assessments of 1-RM are time consuming and unsafe for novice lifters. Whilst various equations exist to predict 1-RM, there is limited research on the validity of these equations. The purpose of this study was to assess the validity of using sub-maximal ratings of perceived exertion (RPE) to predict 1-RM in young adults, using the Borg 6-20 RPE Scale. Twenty healthy participants (ten male (Mean ± SD, 20.8 ± 0.6 y, 75.7 ± 9.3 kg, 1.8 ± 0.07 m) and ten female (20.3 ± 0.7 y, 68.4 ± 10.0 kg, 1.68 ± 0.03 m)) completed two trials involving resistance exercises for both the upper and lower body. In the first trial the 1-RM for the bilateral biceps curl (BC) and the bilateral knee extension (KE) were determined for each participant. In the second trial, participants performed blinded repetitions which were equivalent to 20, 40 and 60 % of 1-RM for both exercises. The RPE was recorded immediately after two repetitions had been completed at each intensity. The order of intensity of the repetitions was randomly assigned with participants wearing blindfolds to exclude the possibility of pre-determined judgments about load and RPE. Individual RPE recorded at each intensity was subjected to linear regression analysis and the line of best fit was extrapolated to RPE 20 to predict 1-RM in both exercises. There was no significant difference (p > 0.05) between the 1-RM predicted from RPE 20 and measured 1-RM for both exercises for the men and women. Measured and predicted values for men were 46.0 ± 4.6 and 45.2 ± 6. 1 kg for biceps curl, and 46.3 ± 3.8 and 43.0 ± 7.1 kg for knee extension, respectively. Measured and predicted values for women were 18.6 ± 5.7 and 19.3 ± 5.6 kg for biceps curl, and 25.5 ± 9.6 and 27.2 ± 12.6 kg for knee extension, respectively. Pearson product-moment correlation coefficients between actual and predicted 1-RM for the BC and KE were 0.97 and 0

  18. Cardiac Autonomic Function during Submaximal Treadmill Exercise in Adults with Down Syndrome

    Science.gov (United States)

    Mendonca, Goncalo V.; Pereira, Fernando D.; Fernhall, Bo

    2011-01-01

    This study determined whether the cardiac autonomic function of adults with Down syndrome (DS) differs from that of nondisabled persons during submaximal dynamic exercise. Thirteen participants with DS and 12 nondisabled individuals performed maximal and submaximal treadmill tests with metabolic and heart rate (HR) measurements. Spectral analysis…

  19. Is energy expenditure taken into account in human sub-maximal jumping? - a simulation study

    NARCIS (Netherlands)

    Vanrenterghem, J.; Bobbert, M.F.; Casius, L.J.R.; de Clercq, D.

    2008-01-01

    This paper presents a simulation study that was conducted to investigate whether the stereotyped motion pattern observed in human sub-maximal jumping can be interpreted from the perspective of energy expenditure. Human sub-maximal vertical countermovement jumps were compared to jumps simulated with

  20. A New Submaximal Rowing Test to Predict 2,000-m Rowing Ergometer Performance

    NARCIS (Netherlands)

    Otter, Ruby T. A.; Brink, Michel S.; Lamberts, Robert P.; Lemmink, Koen A. P. M.

    Otter, RTA, Brink, MS, Lamberts, RP, and Lemmink, KAPM. A new submaximal rowing test to predict 2,000-m rowing ergometer performance. J Strength Cond Res 29(9): 2426-2433, 2015-The purpose of this study was to assess predictive value of a new submaximal rowing test (SmRT) on 2,000-m ergometer rowing

  1. Effect of the Canadian Air Force training programme on a submaximal exercise test.

    Science.gov (United States)

    Kappagoda, C T; Linden, R J; Newell, J P

    1979-07-01

    Validation of the submaximal heart rate/oxygen consumption relationship as an index of 'cardiorespiratory fitness' requires the demonstration of systematic alterations in this relationship concomitant with interventions designed to alter physical fitness. To fulfil those criteria a longitudinal training/de-training study was undertaken. Previously sedentary adult subjects undertook the Canadian Airforce 5BX-XBX exercise programme. Submaximal exercise tests were performed before and after training, and following several weeks cessation of training. A regression line of submaximal heart rate on submaximal oxygen consumption was calculated from the data of each submaximal exercise test. Alterations in the regression lines were examined for each subject individually by testing statistically for difference in slope and elevation between any pair of lines. Subjects who undertook the training/de-training study demonstrated significant systematic alterations in the elevation of the regression lines concomitant with periods of training and de-training. The reproducibility of the submaximal heart rate/oxygen consumption relationship was examined in two additional groups of subjects. Group A repeated a submaximal test on 3 or 4 successive days; Group B were tested before and after 16 weeks of normal activity. Subjects in Group A demonstrated non significant, random alterations in the regression lines on repeated testing and subjects in Group B demonstrated random, though on occasion significant, alterations in the regression lines. The elevation of the submaximal heart rate/oxygen consumption relationship is therefore a valid index for detecting sequential changes in 'cardiorespiratory fitness' in individual subjects.

  2. Reliability of oscillometric central blood pressure responses to submaximal exercise.

    Science.gov (United States)

    Lim, Weijie; Faulkner, James; Lambrick, Danielle; Stoner, Lee

    2016-06-01

    Central blood pressure responses to exercise may provide clinicians with a superior diagnostic and prognostic tool. However, to be of value in a clinical setting these assessments must be simple to conduct and reliable. Using oscillometric pulse wave analysis (PWA), determine the upper limit for between-day reliability of central SBP (cSBP) and central pressure augmentation (AIx) responses to three progressive stages of submaximal exercise in a cohort of young, healthy participants. Fifteen healthy males [25.8 years (SD 5.7), 23.9 kg/m (SD 2.5)] were tested on three different mornings in a fasted state, separated by a maximum of 14 days. Central hemodynamic variables were assessed on the left upper arm. Participants underwent three progressive stages of submaximal cycling at 50 W (low), 100 W (moderate) and 150 W (moderate-hard). During low and moderate-intensity exercise the intra-class correlation coefficient (ICC) values for cSBP (0.79-0.80) and AIx (0.81-0.85) indicated excellent reliability (ICC > 0.75). For the moderate-hard intensity AIx could not be computed, and the ICC for cSBP was adequate (0.72). Findings from this study suggest that, at least in a young, healthy cohort, oscillometric PWA can be used to reliably assess central blood pressure measurements during exercise, up to a moderate intensity. Although further work is required to verify these findings in clinical cohorts, these measurements may potentially provide clinicians with a practical option for obtaining important hemodynamic information beyond that provided by resting peripheral blood pressure.

  3. Which factors determine the freely chosen cadence during submaximal cycling?

    Science.gov (United States)

    Vercruyssen, Fabrice; Brisswalter, Jeanick

    2010-03-01

    The present review of cycling science focuses on the identification of criteria that affect the freely chosen cadence (FCC) during submaximal exercise of short and prolonged durations. Cadence selection during submaximal cycling constitutes a potential parameter affecting the endurance performance in subjects of varying aerobic fitness level and experience. The activity constraints such as specificity (e.g. cycle bout of triathlon) and exercise duration may play an important role in the selection of cadence and must be taken into consideration in the task description. The 'holistic' approach of this review is based on a multifactorial analysis considering the cycling constraints, and the physiological and biomechanical factors of cadence selection so as to establish any interrelationships between these factors. During cycle bouts of short duration (<15 min), it has been well argued that experienced cyclists, trained runners and triathletes adopt high cadences (80-100 rpm) systematically above the energetically optimal cadence (EOC) at which the oxygen uptake is minimal (55-65 rpm). The choice of a high cadence has been shown to be dependent upon several factors, such as the aerobic fitness level, the reduction in forces applied to the cranks, the lower extremity net joint moments and minimal neuromuscular fatigue. However, with increasing exercise duration the FCC has been reported to be close to the EOC exclusively in endurance athletes practising a variety of activities, suggesting an impact of training mode on the muscular adaptations and the organisation of the movement pattern. Copyright 2009 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

  4. Reliability and Seasonal Changes of Submaximal Variables to Evaluate Professional Cyclists.

    Science.gov (United States)

    Rodríguez-Marroyo, Jose A; Pernía, Raúl; Villa, José G; Foster, Carl

    2017-11-01

    The aim of this study was to determine the reliability and validity of several submaximal variables that can be easily obtained by monitoring cyclists' performances. Eighteen professional cyclists participated in this study. In a first part (n = 15) the test-retest reliability of heart rate (HR) and rating of perceived exertion (RPE) during a progressive maximal test was measured. Derived submaximal variables based on HR, RPE, and power output (PO) responses were analyzed. In a second part (n = 7) the pattern of the submaximal variables according to cyclists' training status was analyzed. Cyclists were assessed 3 times during the season: at the beginning of the season, before the Vuelta a España, and the day after this Grand Tour. Part 1: No significant differences in maximal and submaximal variables between test-retest were found. Excellent ICCs (0.81-0.98) were obtained in all variables. Part 2: The HR and RPE showed a rightward shift from early to peak season. In addition, RPE showed a left shift after the Vuelta a España. Submaximal variables based on RPE had the best relationship with both performance and changes in performance. The present study showed the reliability of different maximal and submaximal variables used to assess cyclists' performances. Submaximal variables based on RPE seem to be the best to monitor changes in training status over a season.

  5. Relationship between the Pedaling Biomechanics and Strain of Bicycle Frame during Submaximal Tests

    Directory of Open Access Journals (Sweden)

    Aneliya V. Manolova

    2015-06-01

    Full Text Available The aim of this study was to analyse the effect of forces applied to pedals and cranks on the strain imposed to an instrumented bicycle motocross (BMX frame. Using results from a finite element analysis to determine the localisation of highest stress, eight strain gauges were located on the down tube, the seat tube and the right chain stay. Before the pedaling tests, static loads were applied to the frame during bench tests. Two pedaling conditions have been analysed. In the first, the rider was in static standing position on the pedals and applied maximal muscular isometric force to the right pedal. The second pedaling condition corresponds to three pedaling sprint tests at submaximal intensities at 150, 300 and 550 W on a cycle-trainer. The results showed that smaller strain was observed in the pedaling condition than in the rider static standing position condition. The highest strains were located in the seat tube and the right chain stay near the bottom bracket area. The maximum stress observed through all conditions was 41 MPa on the right chain stay. This stress was 11 times lower than the yield stress of the frame material (460 MPa. This protocol could help to adapt the frame design to the riders as a function of their force and mechanical power output. These results could also help design BMX frames for specific populations (females and rider morphology.

  6. THE VALIDITY OF SUBMAXIMAL RATINGS OF PERCEIVED EXERTION TO PREDICT ONE REPETITION MAXIMUM

    Directory of Open Access Journals (Sweden)

    Harrison James Llewelyn Evans

    2009-12-01

    Full Text Available The One Repetition Maximum (1-RM test is commonly used to assess strength. However, direct assessments of 1-RM are time consuming and unsafe for novice lifters. Whilst various equations exist to predict 1-RM, there is limited research on the validity of these equations. The purpose of this study was to assess the validity of using sub-maximal ratings of perceived exertion (RPE to predict 1-RM in young adults, using the Borg 6-20 RPE Scale. Twenty healthy participants (ten male (Mean ± SD, 20.8 ± 0.6 y, 75.7 ± 9.3 kg, 1.8 ± 0.07 m and ten female (20.3 ± 0.7 y, 68.4 ± 10.0 kg, 1.68 ± 0.03 m completed two trials involving resistance exercises for both the upper and lower body. In the first trial the 1-RM for the bilateral biceps curl (BC and the bilateral knee extension (KE were determined for each participant. In the second trial, participants performed blinded repetitions which were equivalent to 20, 40 and 60 % of 1-RM for both exercises. The RPE was recorded immediately after two repetitions had been completed at each intensity. The order of intensity of the repetitions was randomly assigned with participants wearing blindfolds to exclude the possibility of pre-determined judgments about load and RPE. Individual RPE recorded at each intensity was subjected to linear regression analysis and the line of best fit was extrapolated to RPE 20 to predict 1-RM in both exercises. There was no significant difference (p > 0.05 between the 1-RM predicted from RPE 20 and measured 1-RM for both exercises for the men and women. Measured and predicted values for men were 46.0 ± 4.6 and 45.2 ± 6. 1 kg for biceps curl, and 46.3 ± 3.8 and 43.0 ± 7.1 kg for knee extension, respectively. Measured and predicted values for women were 18.6 ± 5.7 and 19.3 ± 5.6 kg for biceps curl, and 25.5 ± 9.6 and 27.2 ± 12.6 kg for knee extension, respectively. Pearson product-moment correlation coefficients between actual and predicted 1-RM for the BC and KE were 0

  7. Acclimatization improves submaximal exercise economy at 5533 m.

    Science.gov (United States)

    Latshang, T D; Turk, A J; Hess, T; Schoch, O D; Bosch, M M; Barthelmes, D; Merz, T M; Hefti, U; Hefti, J Pichler; Maggiorini, M; Bloch, K E

    2013-08-01

    We tested whether the better subjective exercise tolerance perceived by mountaineers after altitude acclimatization relates to enhanced exercise economy. Thirty-two mountaineers performed progressive bicycle exercise to exhaustion at 490 m and twice at 5533 m (days 6-7 and day 11), respectively, during an expedition to Mt. Muztagh Ata. Maximal work rate (W(max)) decreased from mean ± SD 356 ± 73 watts at 490 m to 191 ± 49 watts and 193 ± 45 watts at 5533 m, days 6-7 and day 11, respectively; corresponding maximal oxygen uptakes (VO2max ) were 50.7 ± 9.5, 26.3 ± 5.6, 24.7 ± 7.0 mL/min/kg (P = 0.0001 5533 m vs 490 m). On days 6-7 (5533 m), VO(2) at 75% W(max) (152 ± 37 watts) was 1.75 ± 0.45 L/min, oxygen saturation 68 ± 8%. On day 11 (5533 m), at the same submaximal work rate, VO(2) was lower (1.61 ± 0.47 L/min, P scale 50 ± 15 vs 57 ± 20, P = 0.006) and reduced symptoms of acute mountain sickness. We conclude that the better performance and subjective exercise tolerance after acclimatization were related to regression of acute mountain sickness and improved submaximal exercise economy because of lower metabolic demands for non-external work-performing functions. © 2011 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  8. Cardiovascular responses during a submaximal exercise test in patients with Parkinson's disease.

    Science.gov (United States)

    Speelman, Arlène D; Groothuis, Jan T; van Nimwegen, Marlies; van der Scheer, Ellis S; Borm, George F; Bloem, Bastiaan R; Hopman, Maria T E; Munneke, Marten

    2012-01-01

    Patients with Parkinson's disease (PD) are physically less active than controls, and autonomic dysfunction may contribute to this sedentary lifestyle. Specifically, an altered cardiovascular response to physical effort may restrict physical activities. To assess the cardiovascular responses to a submaximal exercise test in PD patients and controls, 546 sedentary PD patients and 29 sedentary healthy controls performed the Åstrand-Rhyming submaximal cycle exercise test. Average heart rate was used to estimate maximal oxygen consumption (VO2max). Variables that may affect submaximal activity in PD patients, including disease severity, fatigue, and level of physical activity in daily life, were recorded. Fewer PD patients (46%) completed the submaximal exercise test successfully than the controls (86%). The estimated VO2max of patients with a successful test was 34% lower than the controls (p physical activities further.

  9. The effect of maximal vs submaximal exertion on postprandial lipid levels in individuals with and without coronary heart disease.

    Science.gov (United States)

    Aronov, David M; Bubnova, Marina G; Perova, Natalia V; Orekhov, Alexander N; Bobryshev, Yuri V

    Decisions about fat consumption and levels of physical activity are among the everyday choices we make in life and risk of coronary heart disease (CHD) can be affected by those choices. The purpose of this study was to investigate the influence of a standard fat load combined with physical exertion of different intensities on the plasma lipid profile of CHD patients and CHD-free individuals. This study looked at the influence of different intensities of physical exercise on postprandial lipid metabolism in 20 healthy men and 36 men with diagnosis of CHD. Venous blood samples were obtained after overnight fasting, 3 hours after standard fat load (before the physical load), and immediately after maximal or submaximal physical exercise on bicycle ergometer. After fat load total cholesterol (TC) concentration did not change in either group. However, after the addition of maximal exercise, TC, triglycerides (TG), low-density lipoprotein cholesterol (LDL-C), and apolipoprotein (Apo) B increased significantly (P < .01) in both groups. After fat load and maximal exercise, there was no change in high-density lipoprotein cholesterol (HDL-C) in healthy men, but in men with CHD, HDL-C fell significantly (P < .01); and Apo AI rose in healthy men (P < .01) but dropped significantly (P < .01) in men with CHD. Submaximal physical exercise (60% of max VO2 load for 40 minutes) after fat load decreased TG level in CHD patients (P < .01) and improved other lipid parameters in both groups significantly (↓LDL-C, ↑HDL-C, ↑Apo AI, ↓Apo B, P < .01). We observed a worsening of physical work capacity in men with CHD (significant reduction of duration and total amount of work performed, maximal VO2, oxygen pulse), during maximal stress test performed 3 hours after fat load. There was a doubling of the number of abnormal stress test results (P < .01). Healthy persons showed an increase in respiratory parameters (ventilation, CO2 production, maximal VO2, and oxygen

  10. Effects of music tempo upon submaximal cycling performance.

    Science.gov (United States)

    Waterhouse, J; Hudson, P; Edwards, B

    2010-08-01

    In an in vivo laboratory controlled study, 12 healthy male students cycled at self-chosen work-rates while listening to a program of six popular music tracks of different tempi. The program lasted about 25 min and was performed on three occasions--unknown to the participants, its tempo was normal, increased by 10% or decreased by 10%. Work done, distance covered and cadence were measured at the end of each track, as were heart rate and subjective measures of exertion, thermal comfort and how much the music was liked. Speeding up the music program increased distance covered/unit time, power and pedal cadence by 2.1%, 3.5% and 0.7%, respectively; slowing the program produced falls of 3.8%, 9.8% and 5.9%. Average heart rate changes were +0.1% (faster program) and -2.2% (slower program). Perceived exertion and how much the music was liked increased (faster program) by 2.4% and 1.3%, respectively, and decreased (slower program) by 3.6% and 35.4%. That is, healthy individuals performing submaximal exercise not only worked harder with faster music but also chose to do so and enjoyed the music more when it was played at a faster tempo. Implications of these findings for improving training regimens are discussed.

  11. Neuromuscular function of the quadriceps muscle during isometric maximal, submaximal and submaximal fatiguing voluntary contractions in knee osteoarthrosis patients.

    Directory of Open Access Journals (Sweden)

    Anett Mau-Moeller

    and neuromuscular activation, but also with an impaired position and torque control at submaximal torque levels, an altered EMG-torque relationship and a higher performance fatigability of the quadriceps muscle. It is recommended that the rehabilitation includes strengthening and fatiguing exercises at maximal and submaximal force levels.

  12. Actual Versus Predicted Cardiovascular Demands in Submaximal Cycle Ergometer Testing.

    Science.gov (United States)

    Hoehn, Amanda M; Mullenbach, Megan J; Fountaine, Charles J

    The Astrand-Rhyming cycle ergometer test (ARCET) is a commonly administered submaximal test for estimating aerobic capacity. Whereas typically utilized in clinical populations, the validity of the ARCET to predict VO 2max in a non-clinical population, especially female, is less clear. Therefore, the purpose of this study was to determine the accuracy of the ARCET in a sample of healthy and physically active college students. Subjects (13 females, 10 males) performed a maximal cycle ergometer test to volitional exhaustion to determine VO 2max . At least 48 hours later, subjects performed the ARCET protocol. Predicted VO 2max was calculated following the ARCET format using the age corrected factor. There was no significant difference (p=.045) between actual (41.0±7.97 ml/kg/min) and predicted VO 2max (40.3±7.58 ml/kg/min). When split for gender there was a significant difference between actual and predicted VO 2 for males, (45.1±7.74 vs. 42.7±8.26 ml/kg/min, p=0.029) but no significant difference observed for females, (37.9±6.9 vs. 38.5±6.77 ml/kg/min, p=0.675). The correlation between actual and predicted VO 2 was r=0.84, phealthy college population of both male and female subjects. Implications of this study suggest the ARCET can be used to assess aerobic capacity in both fitness and clinical settings where measurement via open-circuit spirometry is either unavailable or impractical.

  13. Assessment of cardiorespiratory fitness using submaximal protocol in older adults with mood disorder and Parkinson's disease

    Directory of Open Access Journals (Sweden)

    Natacha Alves de Oliveira

    2013-01-01

    Full Text Available BACKGROUND: Evidence has shown benefits for mental health through aerobic training oriented in percentage of VO2max, indicating the importance of this variable for clinical practice. OBJECTIVE: To validate a method for estimating VO2max using a submaximal protocol in elderly patients with clinically diagnosis as major depressive disorder (MDD and Parkinson's disease (PD. METHODS: The sample comprised 18 patients (64.22 ± 9.92 years with MDD (n = 7 and with PD (n = 11. Three evaluations were performed: I disease staging, II direct measurement of VO2max and III submaximal exercise test. Linear regression was performed to verify the accuracy of estimation in VO2max established in ergospirometry and the predicted VO2max from the submaximal test measurement. We also analyzed the correlation between the Bland-Altman procedures. RESULTS: The regression analysis showed that VO2max values estimated by submaximal protocol associated with the VO2max measured, both in absolute values (R² = 0.65; SEE = 0.26; p < 0.001 and the relative (R² = 0.56; SEE = 3.70; p < 0.001. The Bland-Altman plots for analysis of agreement of showed a good correlation between the two measures. DISCUSSION: The VO2max predicted by submaximal protocol demonstrated satisfactory criterion validity and simple execution compared to ergospirometry.

  14. THE INFLUENCE OF OBESITY AND AMBIENT TEMPERATURE ON PHYSIOLOGICAL AND OXIDATIVE RESPONSES TO SUBMAXIMAL EXERCISE

    OpenAIRE

    Ahn, N.; Kim, K.

    2014-01-01

    This study investigated the effects of obesity and ambient temperature on physiological responses and markers of oxidative stress to submaximal exercise in obese and lean people. Sixteen healthy males were divided into an obese group (n=8, %fat: 27.00±3.00%) and a lean group (n=8, %fat: 13.85±2.45%). Study variables were measured during a 60 min submaximal exercise test at 60% VO2max in a neutral (21±1°C) and a cold (4±1°C) environment. Heart rate, blood lactate, rectal temperature, serum lev...

  15. Submaximal arm crank ergometry : Effects of crank axis positioning on mechanical efficiency, physiological strain and perceived discomfort

    NARCIS (Netherlands)

    van Drongelen, S; Maas, J C; Scheel-Sailer, A; Van Der Woude, L H V

    2009-01-01

    PURPOSE: To evaluate the effect of the spatial orientation of the crank axis on mechanical efficiency, physiological strain and perceived discomfort in submaximal synchronous arm crank ergometry. METHODS: Twelve able-bodied individuals performed 12 submaximal exercise bouts of 3 minutes (women: 20

  16. Intensity-dependent EMG response for the biceps brachii during sustained maximal and submaximal isometric contractions.

    Science.gov (United States)

    Carr, Joshua C; Beck, Travis W; Ye, Xin; Wages, Nathan P

    2016-09-01

    There have been recent attempts to characterize the mechanisms associated with fatigue-induced task failure. We compared the time to failure and the corresponding changes in the surface electromyogram (EMG) during sustained maximal and submaximal isometric force tasks. EMG activity was measured from the biceps brachii of 18 male participants as they sustained either a maximal or submaximal (60 % MVC) isometric contraction of the dominant elbow flexors until force could not be maintained above 55 % MVC. Intensity-dependent patterns of change were observed for EMG amplitude and mean power frequency (MNF) between the two force tasks. Interestingly, the only significant predictor of failure time was the rate of change in EMG MNF during the submaximal task (r (2) = 0.304). In addition, EMG amplitude at submaximal failure was significantly lower (p EMG response emphasize the basis of neuromuscular fatigue and task dependency. Additionally, our data suggest that the EMG MNF should be used when monitoring the progression of local muscle fatigue.

  17. Variation in heart rate during submaximal exercise: Implications for monitoring training : Implications for monitoring training

    NARCIS (Netherlands)

    Lamberts, R.P.; Lemmink, K.A.P.M.; Durandt, J.J.; Lambert, M.I.

    2004-01-01

    A change in heart rate at a controlled submaximal exercise intensity is used as a marker of training status. However, the standard error of measurement has not been studied systematically, and therefore a change in heart rate, which can be considered relevant, has not been determined. Forty-four

  18. THE EFFECT OF SUBMAXIMAL INHALATION ON MEASURES DERIVED FROM FORCED EXPIRATORY SPIROMETRY

    Science.gov (United States)

    THE EFFECT OF SUBMAXIMAL INHALATION ON MEASURES DERIVED FROM FORCED EXPIRATORY SPIROMETRY. William F. McDonnell Human Studies Division, NHEERL, U.S. Environmental Protection Agency, RTP, NC 27711. Short-term exposure to ozone results in a neurally-mediated decrease in the ab...

  19. Calibration of EMG to force for knee muscles is applicable with submaximal voluntary contractions

    NARCIS (Netherlands)

    Doorenbosch, C.A.M.; Joosten, A.; Harlaar, J.

    2005-01-01

    Purpose: In this study, the influence of using submaximal isokinetic contractions about the knee compared to maximal voluntary contractions as input to obtain the calibration of an EMG-force model for knee muscles is investigated. Methods: Isokinetic knee flexion and extension contractions were

  20. Variability of Respiration and Metabolism: Responses to Submaximal Cycling and Running.

    Science.gov (United States)

    Armstrong, Lawrence E.; Costill, David L.

    1985-01-01

    This investigation examined day-to-day variations in metabolic measurements during submaximal running and cycling. Significant differences were found in the oxygen uptake (VO2) of runners and cyclists and the minute ventilation (VE) of cyclists while running, but blood lactic acid (HLA) did not differ day to day. (Author/MT)

  1. Is an elevated submaximal heart rate associated with psychomotor slowness in young elite soccer players?

    NARCIS (Netherlands)

    Brink, Michel S.; Visscher, Chris; Schmikli, Sandor L.; Nederhof, E.; Lemmink, Koen A. P. M.

    2013-01-01

    The aim of the present study was to find early markers for overreaching that are applicable in sport practice. In a group of elite soccer players aged 1518, the stressrecovery balance and reaction times before and after exercise were assessed. Overreaching was indicated by an elevated submaximal

  2. Systolic blood pressure reactivity during submaximal exercise and acute psychological stress in youth

    Science.gov (United States)

    Background: Studies in youth show an association between systolic blood-pressure (SBP) reactivity to acute psychological stress and carotid artery intima-media thickness (CIMT). However, it has not yet been determined whether SBP reactivity during submaximal exercise is also associated with CIMT i...

  3. Eight weeks of intermittent hypoxic training improves submaximal physiological variables in highly trained runners.

    Science.gov (United States)

    Holliss, Ben A; Burden, Richard J; Jones, Andrew M; Pedlar, Charles R

    2014-08-01

    It is unclear whether intermittent hypoxic training (IHT) results in improvements in physiological variables associated with endurance running. Twelve highly trained runners (VO2peak 70.0 ± 3.5 ml·kg-1·min-1) performed incremental treadmill tests to exhaustion in normobaric normoxia and hypoxia (16.0% FIO2) to assess submaximal and maximal physiological variables and the limit of tolerance (T-Lim). Participants then completed 8 weeks of moderate to heavy intensity normoxic training (control [CONT]) or IHT (twice weekly 40 minutes runs, in combination with habitual training), in a single blinded manner, before repeating the treadmill tests. Submaximal heart rate decreased significantly more after IHT (-5 ± 5 b·min-1; p = 0.001) than after CONT ( -1 ± 5 b·min-1; p = 0.021). Changes in submaximal V[Combining Dot Above]O2 were significantly different between groups (p ≤ 0.05); decreasing in the IHT group in hypoxia (-2.6 ± 1.7 ml·kg-1·min-1; p = 0.001) and increasing in the CONT group in normoxia (+1.1 ± 2.1 ml·kg-1·min-1; p = 0.012). There were no VO2peak changes within either group, and while T-Lim improved post-IHT in hypoxia (p = 0.031), there were no significant differences between groups. Intermittent hypoxic training resulted in a degree of enhanced cardiovascular fitness that was evident during submaximal, but not maximal intensity exercise. These results suggest that moderate to heavy intensity IHT provides a mean of improving the capacity for submaximal exercise and may be useful for pre-acclimatization for subsequent exercise in hypoxia, but additional research is required to establish its efficacy for athletic performance at sea level.

  4. Prolonged administration of recombinant human erythropoietin increases submaximal performance more than maximal aerobic capacity

    DEFF Research Database (Denmark)

    Thomsen, J J; Rentsch, R L; Robach, P

    2007-01-01

    The effects of recombinant human erythropoietin (rHuEpo) treatment on aerobic power (VO2max) are well documented, but little is known about the effects of rHuEpo on submaximal exercise performance. The present study investigated the effect on performance (ergometer cycling, 20-30 min at 80......HuEpo treatment VO2max increased (PVO2max) was increased by 54.0 and 54.3% (P... week 11), TTE was decreased by 26.8% as compared to pre rHuEpo administration. In conclusion, in healthy non-athlete subjects rHuEpo administration prolongs submaximal exercise performance by about 54% independently of the approximately 12% increase in VO2max....

  5. Iron Status in Chronic Heart Failure: Impact on Symptoms, Functional Class and Submaximal Exercise Capacity.

    Science.gov (United States)

    Enjuanes, Cristina; Bruguera, Jordi; Grau, María; Cladellas, Mercé; Gonzalez, Gina; Meroño, Oona; Moliner-Borja, Pedro; Verdú, José M; Farré, Nuria; Comín-Colet, Josep

    2016-03-01

    To evaluate the effect of iron deficiency and anemia on submaximal exercise capacity in patients with chronic heart failure. We undertook a single-center cross-sectional study in a group of stable patients with chronic heart failure. At recruitment, patients provided baseline information and completed a 6-minute walk test to evaluate submaximal exercise capacity and exercise-induced symptoms. At the same time, blood samples were taken for serological evaluation. Iron deficiency was defined as ferritin < 100 ng/mL or transferrin saturation < 20% when ferritin is < 800 ng/mL. Additional markers of iron status were also measured. A total of 538 heart failure patients were eligible for inclusion, with an average age of 71 years and 33% were in New York Heart Association class III/IV. The mean distance walked in the test was 285 ± 101 meters among those with impaired iron status, vs 322 ± 113 meters (P=.002). Symptoms during the test were more frequent in iron deficiency patients (35% vs 27%; P=.028) and the most common symptom reported was fatigue. Multivariate logistic regression analyses showed that increased levels of soluble transferrin receptor indicating abnormal iron status were independently associated with advanced New York Heart Association class (P < .05). Multivariable analysis using generalized additive models, soluble transferrin receptor and ferritin index, both biomarkers measuring iron status, showed a significant, independent and linear association with submaximal exercise capacity (P=.03 for both). In contrast, hemoglobin levels were not significantly associated with 6-minute walk test distance in the multivariable analysis. In patients with chronic heart failure, iron deficiency but not anemia was associated with impaired submaximal exercise capacity and symptomatic functional limitation. Copyright © 2015 Sociedad Española de Cardiología. Published by Elsevier España, S.L.U. All rights reserved.

  6. A Submaximal Running Test With Postexercise Cardiac Autonomic and Neuromuscular Function in Monitoring Endurance Training Adaptation.

    Science.gov (United States)

    Vesterinen, Ville; Nummela, Ari; Laine, Tanja; Hynynen, Esa; Mikkola, Jussi; Häkkinen, Keijo

    2017-01-01

    Vesterinen, V, Nummela, A, Laine, T, Hynynen, E, Mikkola, J, and Häkkinen, K. A submaximal running test with postexercise cardiac autonomic and neuromuscular function in monitoring endurance training adaptation. J Strength Cond Res 31(1): 233-243, 2017-The aim of this study was to investigate whether a submaximal running test (SRT) with postexercise heart rate recovery (HRR), heart rate variability (HRV), and countermovement jump (CMJ) measurements could be used to monitor endurance training adaptation. Thirty-five endurance-trained men and women completed an 18-week endurance training. Maximal endurance performance and maximal oxygen uptake were measured every 8 weeks. In addition, SRTs with postexercise HRR, HRV, and CMJ measurements were carried out every 4 weeks. Submaximal running test consisted of two 6-minute stages at 70 and 80% of maximum heart rate (HRmax) and a 3-minute stage at 90% HRmax, followed by a 2-minute recovery stage for measuring postexercise HRR, HRV, and CMJ test. The highest responders according to the change of maximal endurance performance showed a significant improvement in running speeds during stages 2 and 3 in SRT, whereas no changes were observed in the lowest responders. The strongest correlation was found between the change of maximal endurance performance and running speed during stage 3, whereas no significant relationships were found between the change of maximal endurance performance and the changes of postexercise HRR, HRV, and CMJ. Running speed at 90% HRmax intensity was the most sensitive variable to monitor adaptation to endurance training. The present submaximal test showed potential to monitor endurance training adaptation. Furthermore, it may serve as a practical tool for athletes and coaches to evaluate weekly the effectiveness of training program without interfering in the normal training habits.

  7. Effect of inspiratory muscle warm-up on submaximal rowing performance.

    Science.gov (United States)

    Arend, Mati; Mäestu, Jarek; Kivastik, Jana; Rämson, Raul; Jürimäe, Jaak

    2015-01-01

    Performing inspiratory muscle warm-up might increase exercise performance. The aim of this study was to investigate the impact of inspiratory muscle warm-up to submaximal rowing performance and to find if there is an effect on lactic acid accumulation and breathing parameters. Ten competitive male rowers aged between 19 and 27 years (age, 23.1 ± 3.8 years; height, 188.1 ± 6.3 cm; body mass, 85.6 ± 6.6 kg) were tested 3 times. During the first visit, maximal inspiratory pressure (MIP) assessment and the incremental rowing test were performed to measure maximal oxygen consumption and maximal aerobic power (Pamax). A submaximal intensity (90% Pamax) rowing test was performed twice with the standard rowing warm-up as test 1 and with the standard rowing warm-up and specific inspiratory muscle warm-up as test 2. During the 2 experimental tests, distance, duration, heart rate, breathing frequency, ventilation, peak oxygen consumption, and blood lactate concentration were measured. The only value that showed a significant difference between the test 1 and test 2 was breathing frequency (52.2 ± 6.8 vs. 53.1 ± 6.8, respectively). Heart rate and ventilation showed a tendency to decrease and increase, respectively, after the inspiratory muscle warm-up (p < 0.1). Despite some changes in respiratory parameters, the use of 40% MIP intensity warm-up is not suggested if the mean intensity of the competition is at submaximal level (at approximately 90% maximal oxygen consumption). In conclusion, the warm-up protocol of the respiratory muscles used in this study does not have a significant influence on submaximal endurance performance in highly trained male rowers.

  8. Characterization of Symmetry Properties of First Integrals for Submaximal Linearizable Third-Order ODEs

    Directory of Open Access Journals (Sweden)

    K. S. Mahomed

    2013-01-01

    Full Text Available The relationship between first integrals of submaximal linearizable third-order ordinary differential equations (ODEs and their symmetries is investigated. We obtain the classifying relations between the symmetries and the first integral for submaximal cases of linear third-order ODEs. It is known that the maximum Lie algebra of the first integral is achieved for the simplest equation and is four-dimensional. We show that for the other two classes they are not unique. We also obtain counting theorems of the symmetry properties of the first integrals for these classes of linear third-order ODEs. For the 5 symmetry class of linear third-order ODEs, the first integrals can have 0, 1, 2, and 3 symmetries, and for the 4 symmetry class of linear third-order ODEs, they are 0, 1, and 2 symmetries, respectively. In the case of submaximal linear higher-order ODEs, we show that their full Lie algebras can be generated by the subalgebras of certain basic integrals.

  9. The Usefulness of Submaximal Exercise Gas Exchange in Pulmonary Arterial Hypertension: A Case Series

    Directory of Open Access Journals (Sweden)

    Paul R. Woods

    2010-04-01

    Full Text Available Introduction Submaximal exercise gas exchange may be a useful tool to track responses to therapy in pulmonary arterial hypertension (PAH patients. Methods Three patients diagnosed with idiopathic PAH, on differing therapies, were included. Standard clinical tests (echocardiography; 6 minute walk were performed pre and 3-5 months after treatment. Gas exchange was measured during 3 minutes of step exercise at both time points. Results Gas exchange variables, end tidal CO 2 (P ET CO 2 and the ratio of ventilation to CO 2 production (V E /VCO 2 , during submaximal exercise were able to track patient responses to therapy over a 3-5 month period. Two patients demonstrated positive improvements, with an increased P ET CO 2 and decreased V E /VCO 2 during light exercise, in response to an altered therapeutic regime. The third patient had a worsening of gas exchange (decreased P ET CO 2 and increased V E /VCO 2 following no changes in the medical regime from the baseline visit. Conclusion Gas exchange variables measured during light submaximal exercise, such as P ET CO 2 and V E /VCO 2 , may be able to better detect small changes in functional status following treatment and could, therefore, be a useful tool to track disease severity in PAH patients. Further study is required to determine the clinical usefulness of these gas exchange variables.

  10. THE INFLUENCE OF OBESITY AND AMBIENT TEMPERATURE ON PHYSIOLOGICAL AND OXIDATIVE RESPONSES TO SUBMAXIMAL EXERCISE

    Directory of Open Access Journals (Sweden)

    N. Ahn

    2014-07-01

    Full Text Available This study investigated the effects of obesity and ambient temperature on physiological responses and markers of oxidative stress to submaximal exercise in obese and lean people. Sixteen healthy males were divided into an obese group (n=8, %fat: 27.00±3.00% and a lean group (n=8, %fat: 13.85±2.45%. Study variables were measured during a 60 min submaximal exercise test at 60% VO2max in a neutral (21±1°C and a cold (4±1°C environment. Heart rate, blood lactate, rectal temperature, serum levels of malondialdehyde (MDA and superoxide dismutase (SOD were measured at rest, during exercise and in recovery. Heart rate of both groups was significantly lower (P<0.05 in the cold than the warm environment, but there were no significant differences between the two groups. Serum SOD activity increased to a significantly greater extent (P<0.05 in the cold than the neutral environment, and remained elevated for longer during exercise in the obese group than the lean group. Serum MDA level during submaximal exercise was not significantly different between conditions or groups. Cold stress in exercise may challenge antioxidant defence mechanisms in obese subjects, but lipid peroxidation remains unchanged.

  11. Variation in heart rate during submaximal exercise: implications for monitoring training.

    Science.gov (United States)

    Lamberts, Robert P; Lemmink, Koen A P M; Durandt, Justin J; Lambert, Michael I

    2004-08-01

    A change in heart rate at a controlled submaximal exercise intensity is used as a marker of training status. However, the standard error of measurement has not been studied systematically, and therefore a change in heart rate, which can be considered relevant, has not been determined. Forty-four subjects (26.5 +/- 5.4 years; mean +/- standard deviation) participated in a submaximal running test at the same time of day for 5 consecutive days. Heart rates were determined during each of the 4 exercise intensities (2 minutes each) of increasing intensity and during the 1-minute recovery period after each stage. The repeatability of the heart rate on a day-to-day basis during the stages and recovery periods were high (intraclass correlation coefficient: 95% confidence interval R = 0.94- 0.99). The lowest variation in heart rate occurred in the fourth stage ( approximately 90% maximum heart rate) with heart rate varying 5 +/- 2 b.min(-1) (95% confidence interval for coefficient of variation = 1.1-1.4%). In conclusion, the standard error of measurement of submaximal heart rate is 1.1-1.4%. This magnitude of measurement error needs to be considered when heart rate is used as a marker of training status.

  12. Measuring submaximal performance parameters to monitor fatigue and predict cycling performance: a case study of a world-class cyclo-cross cyclist.

    Science.gov (United States)

    Lamberts, Robert P; Rietjens, Gerard J; Tijdink, Hendrik H; Noakes, Timothy D; Lambert, Michael I

    2010-01-01

    Recently a novel submaximal test, known as the Lamberts and Lambert submaximal cycle test (LSCT), has been developed with the purpose of monitoring and predicting changes in cycling performance. Although this test has been shown to be reliable and able to predict cycling performance, it is not known whether it can measure changes in training status. Therefore, the aim of this study was to determine whether the LSCT is able to track changes in performance parameters, and objective and subjective markers of well-being. A world class cyclo-cross athlete (31 years) volunteered to participate in a 10-week observational study. Before and after the study, a peak power output (PPO) test with respiratory gas analysis (VO(2max)) and a 40-km time trial (40-km TT) test were performed. Training data were recorded in a training logbook with a daily assessment of well-being, while a weekly LSCT was performed. After the training period all performance parameters had improved by a meaningful amount (PPO +5.2%; 40-km TT time -2.5%; VO(2max) +1.4%). Increased training loads during weeks 2 and 6 and the subsequent training-induced fatigue was reflected in the increased well-being scores. Changes during the LSCT were most clearly notable in (1) increased power during the first minute of third stage, (2) increased rating of perceived exertion during second and third stages, and (3) a faster heart rate recovery after the third stage. In conclusion, these data suggest that the LSCT is able to track changes in training status and detect the consequences of sharp increases in training loads which seem to be associated with accumulating fatigue.

  13. [Comparison of submaximal front crawl and breast stroke swimming in relation to energy expenditure].

    Science.gov (United States)

    Sugiyama, K; Katamoto, S

    1992-11-01

    The purpose of this study was to compare the energy expenditure during submaximal front crawl (Fr) and breast stroke (Br) swimming. Six male college swimmers performed submaximal and maximal exercise tests in both styles in a swimming flume. In submaximal exercise tests, they swam at the following given velocities for 5 min, Br: 0.3, 0.5 and 0.7 m/sec; Fr: 0.3, 0.5, 0.7 and 0.9 m/sec. In maximal exercise tests, following submaximal swimming at 0.9 m/sec in Br and 1.1 m/sec in Fr, swimming velocity was increased progressively by 0.1 m/sec every 1 min until the subjects reached to voluntary exhaustion. VO2max obtained from the maximal swimming tests in Br and Fr were 4.27 and 4.18 l/min, respectively. And there was no significant difference between these two values. VO2 during Br and Fr swimming at four and five submaximal velocities were 1.06, 1.30, 1.79, 2.65 l/min and 1.17, 1.34, 1.63, 2.04, 3.05 l/min, respectively. And, it was found that VO2 at 0.3 and 0.9 m/sec were significantly different (p styles curvilinearly increased with swimming velocity, and these relationships were well fitted for the regression equation of the second order (Br: y = 3.84625x2 - 1.95914x + 1.310463,r2 = 0.999 (p < 0.05), Fr: y = 3.233446x2 - 2.28136x + 1.611524, r2 = 0.979 (p < 0.05)). It was calculated that the two curves crossed at a point on 0.49 m/sec, and that VO2 at this point was 1.27 l/min. This value equivalented to 30.4% VO2max in Br and 29.7% VO2max in Fr.(ABSTRACT TRUNCATED AT 250 WORDS)

  14. Effects of Pedal Speed and Crank Length on Pedaling Mechanics during Submaximal Cycling

    Science.gov (United States)

    BARRATT, PAUL RICHARD; MARTIN, JAMES C.; ELMER, STEVE J.; KORFF, THOMAS

    2016-01-01

    ABSTRACT During submaximal cycling, the neuromuscular system has the freedom to select different intermuscular coordination strategies. From both a basic science and an applied perspective, it is important to understand how the central nervous system adjusts pedaling mechanics in response to changes in pedaling conditions. Purpose To determine the effect of changes in pedal speed (a marker of muscle shortening velocity) and crank length (a marker of muscle length) on pedaling mechanics during submaximal cycling. Methods Fifteen trained cyclists performed submaximal isokinetic cycling trials (90 rpm, 240 W) using pedal speeds of 1.41 to 1.61 m·s−1 and crank lengths of 150 to 190 mm. Joint powers were calculated using inverse dynamics. Results Increases in pedal speed and crank length caused large increases knee and hip angular excursions and velocities (P 0.05). Joint moments and joint powers were less affected by changes in the independent variables, but some interesting effects and trends were observed. Most noteworthy, knee extension moments and powers tended to decrease, whereas hip extension power tended to increase with an increase in crank length. Conclusions The distribution of joint moments and powers is largely maintained across a range of pedaling conditions. The crank length induced differences in knee extension moments, and powers may represent a trade-off between the central nervous system’s attempts to simultaneously minimize muscle metabolic and mechanical stresses. These results increase our understanding of the neural and mechanical mechanisms underlying multi-joint task performance, and they have practical relevance to coaches, athletes, and clinicians. PMID:26559455

  15. [Submaximal exercise capacity and quality of life in exclusive water-pipe smokers].

    Science.gov (United States)

    Ben Saad, H; Babba, M; Boukamcha, R; Latiri, I; Knani, J; Slama, R; Bougmiza, I; Zbidi, A; Tabka, Z

    2010-05-01

    It is well known that oxidative stress is increased significantly by regular water-pipe smoking (WPS). This could lead to muscle dysfunction and thus to impairments of exercise and quality of life (QOL). Considering the impressive number of WP smokers, we intend to investigate the potential effect of WPS on submaximal exercise capacity and QOL. (1). To evaluate the submaximal exercise capacity by the 6-minutes walking test (6-MWT). (2). To compare the deficiency, incapacity and QOL data of exclusive WPS with those of two control groups (never smokers and exclusive cigarette smokers). (3). To determine the factors influencing the 6-minutes walk distance (6-MWD) of WPS subjects. A multicentre study including 180 exclusive WPS [> or =5 WP-year] men aged > or =40 years. Cigar or cigarette smoking, contraindications to the 6-MWT or cortico-steroid therapy will be exclusion criteria. QOL evaluation, spirometry, electrocardiogram and two 6-MWT will be performed. Signs of exercise impairment will be: 6-MWD or =5/10, haemoglobin saturation fall > or =5 points. Data from WPS subjects will be compared with those from 90 never smoking subjects and 90 exclusives cigarettes smokers. (1). WPS will affect significantly the submaximal exercise capacity. (2). Resting spirometric, 6-MWT and QOL data of exclusive WPS subjects will be significantly reduced compared to never smoking subjects. (3). The 6-MWD's of exclusive WPS subjects will be significantly influenced by cumulative WP consumption, by resting spirometric data, by obesity and by physical activity score. Copyright 2010 SPLF. Published by Elsevier Masson SAS. All rights reserved.

  16. The Impact of a Submaximal Level of Exercise on Balance Performance in Older Persons

    Science.gov (United States)

    2014-01-01

    Objective. The purpose of this study was to determine the impact of a submaximal level of exercise on balance performance under a variety of conditions. Material and Method. Thirteen community-dwelling older persons with intact foot sensation (age = 66.69 ± 8.17 years, BMI = 24.65 ± 4.08 kg/m2, female, n = 6) volunteered to participate. Subjects' balance performances were measured using the Modified Clinical Test of Sensory Integration of Balance (mCTSIB) at baseline and after test, under four conditions of stance: (1) eyes-opened firm-surface (EOF), (2) eyes-closed firm-surface (ECF), (3) eyes-opened soft-surface (EOS), and (4) eyes-closed soft-surface (ECS). The 6-minute walk test (6MWT) protocol was used to induce the submaximal level of exercise. Data was analyzed using the Wilcoxon Signed-Rank Test. Results. Balance changes during EOF (z = 0.00, P = 1.00) and ECF (z = −1.342, P = 0.180) were not significant. However, balance changes during EOS (z = −2.314, P = 0.021) and ECS (z = −3.089, P = 0.02) were significantly dropped after the 6MWT. Conclusion. A submaximal level of exercise may influence sensory integration that in turn affects balance performance, particularly on an unstable surface. Rehabilitation should focus on designing intervention that may improve sensory integration among older individuals with balance deterioration in order to encourage functional activities. PMID:25383386

  17. Effects of submaximal and supramaximal interval training on determinants of endurance performance in endurance athletes.

    Science.gov (United States)

    Paquette, M; Le Blanc, O; Lucas, S J E; Thibault, G; Bailey, D M; Brassard, P

    2017-03-01

    We compared the effects of submaximal and supramaximal cycling interval training on determinants of exercise performance in moderately endurance-trained men. Maximal oxygen consumption (VO2max ), peak power output (Ppeak ), and peak and mean anaerobic power were measured before and after 6 weeks (3 sessions/week) of submaximal (85% maximal aerobic power [MP], HIIT85 , n = 8) or supramaximal (115% MP, HIIT115 , n = 9) interval training to exhaustion in moderately endurance-trained men. High-intensity training volume was 47% lower in HIIT115 vs HIIT85 (304 ± 77 vs 571 ± 200 min; P training was generally associated with increased VO2max (HIIT85 : +3.3 ± 3.1 mL/kg/min; HIIT115 : +3.3 ± 3.6 ml/kg/min; Time effect P = 0.002; Group effect: P = 0.95), Ppeak (HIIT85 : +18 ± 9 W; HIIT115 : +16 ± 27 W; Time effect P = 0.045; Group effect: P = 0.49), and mean anaerobic power (HIIT85 : +0.42 ± 0.69 W/kg; HIIT115 : +0.55 ± 0.65 W/kg; Time effect P = 0.01; Group effect: P = 0.18). Six weeks of submaximal and supramaximal interval training performed to exhaustion seems to equally improve VO2max and anaerobic power in endurance-trained men, despite half the accumulated time spent at the target intensity. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  18. Hypotension and heart rate variability after resistance exercise performed maximal and submaximal order

    Directory of Open Access Journals (Sweden)

    Victor Gonçalves Corrêa Neto

    2017-06-01

    Full Text Available The aim of the study was verified the blood pressure responses and the cardiac autonomic modulation after the strength exercise in two different conditions (maximal and submaximal. The subjects were divided in three groups, such as: maximal repetitions (age: 20.5 ± 0.6 years, weight: 63.7 ± 14.8, height: 1.7 ± 0.1, body mass index: 22.8 ± 4.5 Kilogram per square meter (kg/m², submaximal repetitions (age: 25 ± 4.1 years, weight: 69.1 ± 12.8, height: 1.8 ± 0.1, body mass index: 22.2 ± 1.7 (kg/m²  and a control group (age: 23.7 ± 3.8 years, weight: 64.2 ± 15, height: 1.7 ± 0.1, body mass index: 21.8 ± 1.9 (kg/m². The blood pressure and the Heart Rate R-R intervals were measured before and during one hour after the session, with 10-minutes intervals length between measurements. The analyze of variance did not showed significant differences between experimental protocols to blood pressure (p > 0.05. However, the effect size was able to show that the most intense training caused a reduction in systolic blood pressure at times. Regarding cardiac autonomic response, the group that exercised the submaximal form exhibited a significant increase in LF / HF (p = 0.022 when 20 minutes’ post-exercise. There was a not significant difference in cardiac autonomic modulation between protocols. The high intensity protocol has caused blood pressure reductions in more moments and it was over safer in relation to cardiac autonomic modulation, since it did not cause increased sympathetic activity during recovery.

  19. Effects of wheel and hand-rim size on submaximal propulsion in wheelchair athletes.

    Science.gov (United States)

    Mason, Barry S; Van Der Woude, Lucas H V; Tolfrey, Keith; Lenton, John P; Goosey-Tolfrey, Victoria L

    2012-01-01

    This study aimed to investigate the effects of fixed gear ratio wheel sizes on the physiological and biomechanical responses to submaximal wheelchair propulsion. Highly trained wheelchair basketball players (N = 13) propelled an adjustable sports wheelchair in three different wheel sizes (24, 25, and 26 inches) on a motor-driven treadmill. Each wheel was equipped with force-sensing hand-rims (SMARTWheel), which collected kinetic and temporal data. Oxygen uptake (V˙O2) and HR responses were measured with high-speed video footage collected to determine three-dimensional upper body joint kinematics. Mean power output and work per cycle decreased progressively with increasing wheel size (P wheelchair propulsion.

  20. Comparison of the YMCA and a Custom Submaximal Exercise Test for Determining VO2max.

    Science.gov (United States)

    Jamnick, Nicholas A; By, Savanny; Pettitt, Cherie D; Pettitt, Robert W

    2016-02-01

    The maximal oxygen uptake (VO2max) is deemed the highest predictor for all-cause mortality, and therefore, an ability to assess VO2max is important. The YMCA submaximal test is one of the most widely used tests to estimate VO2max; however, it has questionable validity. We validated a customized submaximal test that accounts for the nonlinear rise in VO2 relative to power output and compared its accuracy against the YMCA protocol. Fifty-six men and women performed a graded exercise test with a subsequent exhaustive, square wave bout for the verification of "true" VO2max. In counterbalanced order, subjects then completed the YMCA test and our new Mankato submaximal exercise test (MSET). The MSET consisted of a 3-min stage estimated at 35% VO2max and a second 3-min stage estimated at either 65% or 70% VO2max, where VO2max was estimated with a regression equation using sex, body mass index, age, and self-reported PA-R. VO2 values from the graded exercise test and square wave verification bout did not differ with the highest value used to identify "true" VO2max (45.1 ± 8.89 mL · kg(-1) · min(-1)). The MSET (43.6 ± 8.6 mL · kg(-1) · min(-1)) did not differ from "true" VO2max, whereas the YMCA test (41.1 ± 9.6 mL · kg(-1) · min(-1)) yielded an underestimation (P = 0.002). The MSET was moderately correlated with "true" VO2max (ICC = 0.73, CV of 11.3%). The YMCA test was poorly correlated with "true" VO2max (ICC = 0.29, CV of 15.1%). To our knowledge, this is the first study to examine submaximal exercise protocols versus a verified VO2max protocol. The MSET yielded better estimates of VO2max because of the protocol including a stage exceeding gas exchange threshold.

  1. Low doses of caffeine reduce heart rate during submaximal cycle ergometry

    Directory of Open Access Journals (Sweden)

    Wetter Thomas J

    2007-10-01

    Full Text Available Abstract Background The purpose of this study was to examine the cardiovascular effects of two low-levels of caffeine ingestion in non habitual caffeine users at various submaximal and maximal exercise intensities. Methods Nine male subjects (19–25 yr; 83.3 ± 3.1 kg; 184 ± 2 cm, underwent three testing sessions administered in a randomized and double-blind fashion. During each session, subjects were provided 4 oz of water and a gelatin capsule containing a placebo, 1.5 mg/kg caffeine, or 3.0 mg/kg caffeine. After thirty minutes of rest, a warm-up (30 Watts for 2 min the pedal rate of 60 rpm was maintained at a steady-state output of 60 watts for five minutes; increased to 120 watts for five minutes and to 180 watts for five minutes. After a 2 min rest the workload was 180 watts for one minute and increased by 30 watts every minute until exhaustion. Heart rate (HR was measured during the last 15-seconds of each minute of submaximal exercise. Systolic blood pressure (BP was measured at rest and during each of the three sub-maximal steady state power outputs. Minute ventilation (VE, Tidal volume (VT, Breathing frequency (Bf, Rating of perceived exertion (RPE, Respiratory exchange ratio (RER, and Oxygen consumption (VO2 were measured at rest and during each minute of exercise. Results Caffeine at 1.5 and 3.0 mg/kg body weight significantly lowered (p E, VT, VO2, RPE, maximal power output or time to exhaustion. Conclusion In non habitual caffeine users it appears that consuming a caffeine pill (1.5 & 3.0 mg/kg at a dose comparable to 1–3 cups of coffee lowers heart rate during submaximal exercise but not at near maximal and maximal exercise. In addition, this caffeine dose also only appears to affect systolic blood pressure at rest but not during cycling exercise.

  2. The Effect of 4 Weeks Fixed and Mixed Intermittent Hypoxic Training (IHT) on Respiratory Metabolic and Acid-base Response of Capillary Blood During Submaximal Bicycle Exercise in Male Elite Taekwondo Players.

    Science.gov (United States)

    Park, Hun-Young; Sunoo, Sub; Nam, Sang-Seok

    2016-12-31

    The purpose of our study was to determine the effectiveness of 4 weeks fixed and mixed intermittent hypoxic training (IHT) and its difference from exercise training at sea-level on exercise load, respiratory metabolic and acid-base response of capillary blood during 80% maximal heart rate (HRmax) bicycle exercise in male elite Taekwondo players. Male elite Taekwondo players (n = 25 out of 33) were randomly assigned to training at sea-level (n = 8, control group), training at 16.5%O 2 (2000 m) simulated hypoxic condition (n = 9, fixed IHT group), and training at 14.5%O 2 (3000 m) up to 2 weeks and 16.5%O 2 (2000 m) simulated hypoxic condition (n = 8, mixed IHT group) for 3 weeks. We compared their average exercise load, respiratory metabolic, and acid-base response of the capillary blood during 80% HRmax submaximal bicycle exercise before and after 4 weeks training. Fixed and mixed IHT groups showed positive improvement in respiratory metabolic and acid-base response of the capillary blood during 80% HRmax submaximal bicycle exercise after 4 weeks training. However, all dependent variables showed no significant difference between fixed IHT and mix IHT. Results suggested that mixed and fixed IHT is effective in improving respiratory metabolic and acid-base response of capillary blood in male elite Taekwondo players. Thus, IHT could be a novel and effective method for improving exercise performance through respiratory metabolic and acid-base response.

  3. Cognitive Performance Enhancement Induced by Caffeine, Carbohydrate and Guarana Mouth Rinsing during Submaximal Exercise

    Directory of Open Access Journals (Sweden)

    Laura Pomportes

    2017-06-01

    Full Text Available The aim of this study was to investigate the influence of serial mouth rinsing (MR with nutritional supplements on cognitive performance (i.e., cognitive control and time perception during a 40-min submaximal exercise. Twenty-four participants completed 4 counterbalanced experimental sessions, during which they performed MR with either placebo (PL, carbohydrate (CHO: 1.6 g/25 mL, guarana complex (GUAc: 0.4 g/25 mL or caffeine (CAF: 67 mg/25 mL before and twice during exercise. The present study provided some important new insights regarding the specific changes in cognitive performance induced by nutritional supplements. The main results were: (1 CHO, CAF and GUA MR likely led participants to improve temporal performance; (2 CAF MR likely improved cognitive control; and (3 CHO MR led to a likely decrease in subjective perception of effort at the end of the exercise compared to PL, GUA and CAF. Moreover, results have shown that performing 40-min submaximal exercise enhances information processing in terms of both speed and accuracy, improves temporal performance and does not alter cognitive control. The present study opens up new perspectives regarding the use of MR to optimize cognitive performance during physical exercise.

  4. Achilles tendinopathy alters stretch shortening cycle behaviour during a sub-maximal hopping task.

    Science.gov (United States)

    Debenham, James R; Travers, Mervyn J; Gibson, William; Campbell, Amity; Allison, Garry T

    2016-01-01

    To describe stretch shortening cycle behaviour of the ankle and lower limb in patients with Achilles tendinopathy (AT) and establish differences with healthy volunteers. Between-subjects case-controlled. Fifteen patients with AT (mean age 41.2±12.7 years) and 11 healthy volunteers (CON) (mean age 23.2±6.7 years) performed sub-maximal single-limb hopping on a custom built sledge-jump system. Using 3D motion analysis and surface EMG, temporal kinematic (lower limb stiffness, ankle angle at 80ms pre-contact, ankle angle at contact, peak ankle angle, ankle stretch amplitude) and EMG measures (onset, offset and peak times relative to contact) were captured. Data between AT and CON were compared statistically using a linear mixed model. Patients with AT exhibited significantly increased lower limb stiffness when compared to healthy volunteers (pbehaviour during sub-maximal hopping when compared with healthy volunteers. Patients with AT hop with greater lower limb stiffness, in a greater degree of ankle dorsiflexion and have a greater stretch amplitude. Likewise, delayed muscle activity is evident. These findings have implications in terms of informing the understanding of the pathoaetiology and management of AT. Copyright © 2014 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

  5. Reliability of heart rate variability threshold and parasympathetic reactivation after a submaximal exercise test

    Directory of Open Access Journals (Sweden)

    Carlos Janssen Gomes da Cruz

    Full Text Available Abstract The objective of this study was to evaluate reproducibility of heart rate variability threshold (HRVT and parasympathetic reactivation in physically active men (n= 16, 24.3 ± 5.1 years. During the test, HRVT was assessed by SD1 and r-MSSD dynamics. Immediately after exercise, r-MSSD was analyzed in segments of 60 seconds for a period of five minutes. High absolute and relatively reproducible analysis of HRVT were observed, as assessed by SD1 and r-MSSD dynamics (ICC = 0.92, CV = 10.8, SEM = 5.8. During the recovery phase, a moderate to high reproducibility was observed for r-MSSD from the first to the fifth minute (ICC = 0.69-0.95, CV = 7.5-14.2, SEM = 0.07-1.35. We conclude that HRVT and r-MSSD analysis after a submaximal stress test are highly reproducible measures that might be used to assess the acute and chronic effects of exercise training on cardiac autonomic modulation during and/or after a submaximal stress test.

  6. VO2@RER1.0: a novel submaximal cardiopulmonary exercise index.

    Science.gov (United States)

    Chin, Clifford; Kazmucha, Jeffrey; Kim, Nancy; Suryani, Reny; Olson, Inger

    2010-01-01

    Maximal oxygen consumption (VO2max) is the "gold standard" by which to assess functional capacity; however, it is effort dependent. VO2@RER1.0 is defined when VO2 = VCO2. Between December 22, 1997 and November 9, 2004, 305 pediatric subjects underwent cycle ergometer cardiopulmonary exercise testing, exercised to exhaustion, and reached a peak respiratory exchange ratio > or = 1.10. Group 1 subjects achieved a peak VO2 > or = 80% of predicted VO2max; group 2 subjects achieved a peak VO2 subjects achieved a peak VO2 between 61 and 79% of predicted VO2max. Linear regression analysis was performed for VO2@RER1.0 as a function of predicted VO2 for group 1 subjects. A -2 SD regression line and equation was created. VO2@RER1.0 data from groups 2 and 3 were plotted onto the normative graph. Contingency table and relative-risk analysis showed that an abnormal VO2@RER1.0 predicted an abnormal peak VO2(positive-predictive value 83%, negative-predictive value 85%, sensitivity 84%, and specificity 84%). VO2@RER1.0 is a highly sensitive, specific, and predictive submaximal index of functional capacity. This submaximal index is easy to identify without subjectivity. This index may aid in the evaluation of subjects who cannot exercise to maximal parameters.

  7. [Sub-maximal aerobic capacity and quality of life of patients with rheumatoid arthritis].

    Science.gov (United States)

    Lataoui, S; Belghali, S; Zeglaoui, H; Bouajina, E; Ben Saad, H

    2017-01-01

    Studies about sub-maximal aerobic capacity of patients with rheumatoid arthritis are scarce. To assess the sub-maximal aerobic capacity of these patients through the 6-min walk test, estimated age of the "muscular and cardiorespiratory" chain. Thirty-seven consecutive patients (aged 20 to 60 years) with newly diagnosed rheumatoid arthritis will be included. Non-inclusion criteria will be: use of drugs (e.g.; methotrexate, beta-blockers), orthopaedic or rheumatologic conditions (other than rheumatoid arthritis) that may alter walking ability and recent infections. Exclusion criteria will be: 6-min walking test contra-indications and imperfect performance of the required lung function and walking maneuvers. Signs of walking intolerance will be: test interruption, distance ≤lower limit of normal, dyspnea score ≥5/10 (visual analogue scale) at the end of the test, haemoglobin oxygen saturation (SpO2) drop ≥5%, cardiac frequency at the end of the test ≤60% of maximum predicted. An estimated "muscular and cardiorespiratory chain" age higher than the chronological one will be considered as a sign of accelerated ageing. A high percentage of patients suffering from rheumatoid arthritis would show evidences of walking limitation and accelerated "muscular and cardiorespiratory chain" ageing. There would be a significant correlation between the walking test and clinical, biological, radiological and pulmonary function data and the patients' quality-of-life status. Copyright © 2016 SPLF. Published by Elsevier Masson SAS. All rights reserved.

  8. Impact of a Submaximal Warm-Up on Endurance Performance in Highly Trained and Competitive Male Runners

    Science.gov (United States)

    Zourdos, Michael C.; Bazyler, Caleb D.; Jo, Edward; Khamoui, Andy V.; Park, Bong-Sup; Lee, Sang-Rok; Panton, Lynn B.; Kim, Jeong-Su

    2017-01-01

    Purpose: The purpose of this investigation was to examine the effects of a submaximal running warm-up on running performance in male endurance athletes (n = 16, M[subscript age] = 21 ± 2 years, M[subscript VO2max] = 69.3 ± 5.1 mL/kg/min). Method: Endurance performance was determined by a 30-min distance trial after control and submaximal running…

  9. Blunted Maximal and Submaximal Responses to Cardiopulmonary Exercise Tests in Patients With Parkinson Disease.

    Science.gov (United States)

    Kanegusuku, Hélcio; Silva-Batista, Carla; Peçanha, Tiago; Nieuwboer, Alice; Silva, Natan D; Costa, Luiz A; de Mello, Marco T; Piemonte, Maria E; Ugrinowitsch, Carlos; Forjaz, Cláudia L

    2016-05-01

    To investigate submaximal and maximal responses during maximal cardiopulmonary exercise tests in subjects with Parkinson disease (PD). Cross-sectional. A PD association. A sample (N=68) of subjects with PD (n=48; mean age, 66±8y; modified Hoehn and Yahr stage between 2 and 3; "on" state of medication) and age-matched controls without PD (n=20; mean age, 64±9y). Maximal cardiopulmonary exercise test on a cycle ergometer. Oxygen uptake (V˙o2), systolic blood pressure (SBP), and heart rate assessed at rest, submaximal intensities (ie, anaerobic threshold [AT] and respiratory compensation point), and maximal intensity (peak exercise). Compared with control subjects, subjects with PD had lower V˙o2, heart rate, and SBP at respiratory compensation point and peak exercise (V˙o2: 14.6±3.6mL⋅kg⋅min vs 17.9±5.5mL⋅kg⋅min and 17.7±4.8mL⋅kg⋅min vs 21.5±6.6mL⋅kg⋅min; heart rate: 119±17beats/min vs 139±12beats/min and 132±20beats/min vs 158±13beats/min; SBP: 151±17mmHg vs 172±20mmHg and 166±21mmHg vs 187±24mmHg; P≤.05). They also had lower heart rate at AT (102±14beats/min vs 110±13beats/min; P≤.05), whereas V˙o2 and SBP at this intensity were similar to those of control subjects. Subjects with PD demonstrated blunted metabolic and cardiovascular responses to submaximal and maximal exercise tests, especially at intensities above AT, which are in line with autonomic disturbances present in patients with PD. Future studies need to determine how this affects performance, participation, and responses of these patients to exercise training at different intensities. Copyright © 2016 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

  10. Aerobic interval training reduces vascular resistances during submaximal exercise in obese metabolic syndrome individuals.

    Science.gov (United States)

    Mora-Rodriguez, Ricardo; Fernandez-Elias, V E; Morales-Palomo, F; Pallares, J G; Ramirez-Jimenez, M; Ortega, J F

    2017-08-12

    The aim of this study was to determine the effects of high-intensity aerobic interval training (AIT) on exercise hemodynamics in metabolic syndrome (MetS) volunteers. Thirty-eight, MetS participants were randomly assigned to a training (TRAIN) or to a non-training control (CONT) group. TRAIN consisted of stationary interval cycling alternating bouts at 70-90% of maximal heart rate during 45 min day(-1) for 6 months. CONT maintained baseline physical activity and no changes in cardiovascular function or MetS factors were detected. In contrast, TRAIN increased cardiorespiratory fitness (14% in VO2PEAK; 95% CI 9-18%) and improved metabolic syndrome (-42% in Z score; 95% CI 83-1%). After TRAIN, the workload that elicited a VO2 of 1500 ml min(-1) increased 15% (95% CI 5-25%; P < 0.001). After TRAIN when subjects pedaled at an identical submaximal rate of oxygen consumption, cardiac output increased by 8% (95% CI 4-11%; P < 0.01) and stroke volume by 10% (95% CI, 6-14%; P < 0.005) being above the CONT group values at that time point. TRAIN reduced submaximal exercise heart rate (109 ± 15-106 ± 13 beats min(-1); P < 0.05), diastolic blood pressure (83 ± 8-75 ± 8 mmHg; P < 0.001) and systemic vascular resistances (P < 0.01) below CONT values. Double product was reduced only after TRAIN (18.2 ± 3.2-17.4 ± 2.4 bt min(-1) mmHg 10(-3); P < 0.05). The data suggest that intense aerobic interval training improves hemodynamics during submaximal exercise in MetS patients. Specifically, it reduces diastolic blood pressure, systemic vascular resistances, and the double product. The reduction in double product, suggests decreased myocardial oxygen demands which could prevent the occurrence of adverse cardiovascular events during exercise in this population. CLINICALTRIALS. NCT03019796.

  11. Prognostic value of treadmill stress echocardiography at extremes of exercise performance: submaximal high exercise capacity ≥ 10 metabolic equivalents.

    Science.gov (United States)

    Yao, Siu-Sun; Agarwal, Vikram; Chaudhry, Farooq A

    2014-03-01

    Submaximal stress testing or achieving High exercise capacity (≥ 10 metabolic equivalents, METS) is a predictor of favorable prognosis. The purpose of this study was to evaluate the prognostic value of submaximal or high exercise capacity stress echocardiography. We evaluated 1781 patients (55 ± 13 years; 59% male) undergoing treadmill stress echocardiography divided into 811 patients with submaximal (high exercise capacity (≥ 10 METS). Resting left ventricular ejection fraction and regional wall motion were assessed. The left ventricle was divided into 16 segments and scored on 5-point scale of wall motion. Abnormal stress echocardiography was defined as stress-induced ischemia (wall-motion score of ≥ 1 grade). Follow-up (3.3 ± 1.5 years) for nonfatal myocardial infarction (MI) (n = 40) and cardiac death (n = 52) were obtained. By univariate analysis, echocardiographic variables of ejection fraction, peak wall-motion score index (WMSI) and number of new ischemic wall-motion abnormalities were significant predictors of cardiac events. Cumulative survival was significantly worse in patients with abnormal (ischemic) versus normal (nonischemic) stress echocardiography in submaximal (4.4%/year vs. 1.3%/year, P high exercise capacity (1.5%/year vs. 0.2%/year, P high exercise capacity studies. © 2013, Wiley Periodicals, Inc.

  12. Cycling on rollers: Kreitler fan resistance at submaximal levels of effort.

    Science.gov (United States)

    Reiser, R F; Hart, C R

    2008-03-01

    The goal of this investigation was to characterize the commercially available fan unit for the KreitlerAlloy rollers at submaximal levels of effort (cyclist rode six times at each of three fan inlet settings (closed, half, and full open) and five fan speeds (900, 1800, 2700, 3600, and 4500 rpm). Fan power requirements were isolated by subtracting roller resistance from separate trials. Power requirements relative to fan inlet and fan speed possessed a significant interaction with the main effects for each also significant (all p or = 0.997). Fan resistance was virtually non existent at 900 rpm. Fan resistance then significantly increased with increasing fan speed and inlet opening. At 4500 rpm power requirements of the fan reached 269 +/- 6, 352 +/- 7, and 406 +/- 9 W with the inlet closed, half, and fully open, respectively (p training and testing environments.

  13. Brief note about plasma catecholamines kinetics and submaximal exercise in untrained standardbreds

    Directory of Open Access Journals (Sweden)

    Paolo Baragli

    2010-03-01

    Full Text Available Four untrained standardbred horses performed a standardized exercise test on the treadmill and an automated blood collection system programmed to obtain blood samples every 15 s was used for blood collection in order to evaluate the kinetics of adrenaline and noradrenaline. The highest average values obtained for adrenaline and noradrenaline were 15.0 ± 3.0 and 15.8 ± 2.8 nmol/l respectively, with exponential accumulation of adrenaline (r = 0.977 and noradrenaline (r = 0.976 during the test. Analysis of the correlation between noradrenaline and adrenaline for each phase of the test shows that correlation coefficient decreases as the intensity of exercise increases (from r = 0.909 to r = 0.788. This suggests that during submaximal exercise, the process for release, distribution and clearance of adrenaline into blood circulation differs from that of noradrenaline.

  14. A new submaximal cycle ergometer test for prediction of VO2max.

    Science.gov (United States)

    Ekblom-Bak, E; Björkman, F; Hellenius, M-L; Ekblom, B

    2014-04-01

    Maximal oxygen uptake (VO2max) is an important, independent predictor of cardiovascular health and mortality. Despite this, it is rarely measured in clinical practice. The aim of this study was to create and evaluate a submaximal cycle ergometry test based on change in heart rate (HR) between a lower standard work rate and an individually chosen higher work rate. In a mixed population (n = 143) with regard to sex (55% women), age (21-65 years), and activity status (inactive to highly active), a model included change in HR per unit change in power, sex, and age for the best estimate of VO2max. The association between estimated and observed VO2max for the mixed sample was r = 0.91, standard error of estimate = 0.302 L/min, and mean measured VO2max = 3.23 L/min. The corresponding coefficient of variation was 9.3%, a significantly improved precision compared with one of the most commonly used submaximal exercise tests, the Åstrand test, which in the present study was estimated to be 18.1%. Test-retest reliability analysis over 1 week revealed no mean difference in the estimated VO2max (-0.02 L/min, 95% confidence interval: -0.07-0.03). The new test is low-risk, easily administered, and valid for a wide capacity range, and is therefore suitable in situations as health evaluations in the general population. © 2012 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  15. Muscle vibration sustains motor unit firing rate during submaximal isometric fatigue in humans.

    Science.gov (United States)

    Griffin, L; Garland, S J; Ivanova, T; Gossen, E R

    2001-09-15

    1. In keeping with the 'muscular wisdom hypothesis', many studies have documented that the firing rate of the majority of motor units decreased during fatiguing isometric contractions. The present study investigated whether the application of periodic muscle vibration, which strongly activates muscle spindles, would alter the modulation of motor unit firing rate during submaximal fatiguing isometric contractions. 2. Thirty-three motor units from the lateral head of the triceps brachii muscle were recorded from 10 subjects during a sustained isometric 20 % maximal voluntary contraction (MVC) of the elbow extensors. Vibration was interposed on the contraction for 2 s every 10 s. Twenty-two motor units were recorded from the beginning of the fatigue task. The discharge rate of the majority of motor units remained constant (12/22) or increased (4/22) with fatigue. Six motor units demonstrated a reduction in discharge rate that later returned toward initial values; these motor units had higher initial discharge rates than the other 16 motor units. 3. In a second series of experiments, four subjects held a sustained isometric 20 % MVC for 2 min and then vibration was applied as above for the remainder of the contraction. In this case, motor units initially demonstrated a decrease in firing rate that increased after the vibration was applied. Thus muscle spindle disfacilitation of the motoneurone pool may be associated with the decline of motor unit discharge rate observed during the first 2 min of the contraction. 4. In a third set of experiments, seven subjects performed the main experiment on one occasion and repeated the fatigue task without vibration on a second occasion. Neither the endurance time of the fatiguing contraction nor the MVC torque following fatigue was affected by the application of vibration. This finding calls into question the applicability of the muscular wisdom hypothesis to submaximal contractions.

  16. Low-protein vegetarian diet does not have a short-term effect on blood acid–base status but raises oxygen consumption during submaximal cycling

    Directory of Open Access Journals (Sweden)

    Hietavala Enni-Maria

    2012-11-01

    Full Text Available Abstract Background Acid–base balance refers to the equilibrium between acids and bases in the human body. Nutrition may affect acid–base balance and further physical performance. With the help of PRAL (potential renal acid load, a low-protein vegetarian diet (LPVD was designed to enhance the production of bases in body. The aim of this study was to investigate if LPVD has an effect on blood acid–base status and performance during submaximal and maximal aerobic cycling. Methods Nine healthy, recreationally active men (age 23.5 ± 3.4 yr participated in the study and were randomly divided into two groups in a cross-over study design. Group 1 followed LPVD for 4 days and group 2 ate normally (ND before performing a cycle ergometer test. The test included three 10-min stages at 40, 60 and 80% of VO2max. The fourth stage was performed at 100% of VO2max until exhaustion. After 10–16 days, the groups started a second 4-day diet, and at the end performed the similar ergometer test. Venous blood samples were collected at the beginning and at the end of both diet periods and after every stage cycled. Results Diet caused no significant difference in venous blood pH, strong ion difference (SID, total concentration of weak acids (Atot, partial pressure of CO2 (pCO2 or HCO3- at rest or during cycling between LPVD and ND. In the LPVD group, at rest SID significantly increased over the diet period (38.6 ± 1.8 vs. 39.8 ± 0.9, p=0.009. Diet had no significant effect on exercise time to exhaustion, but VO2 was significantly higher at 40, 60 and 80% of VO2max after LPVD compared to ND (2.03 ± 0.25 vs. 1.82 ± 0.21 l/min, p=0.035; 2.86 ± 0.36 vs. 2.52 ± 0.33 l/min, p Conclusion There was no difference in venous blood acid–base status between a 4-day LPVD and ND. VO2 was increased during submaximal cycling after LPVD suggesting that the exercise economy was poorer. This had no further effect on maximal aerobic performance. More studies are needed to

  17. The Effects of Caffeine Supplementation on Physiological Responses to Submaximal Exercise in Endurance-Trained Men.

    Science.gov (United States)

    Glaister, Mark; Williams, Benjamin Henley; Muniz-Pumares, Daniel; Balsalobre-Fernández, Carlos; Foley, Paul

    2016-01-01

    The aim of this study was to evaluate the effects of caffeine on physiological responses to submaximal exercise, with a focus on blood lactate concentration ([BLa]). Using a randomised, single-blind, crossover design; 16 endurance-trained, male cyclists (age: 38 ± 8 years; height: 1.80 ± 0.05 m; body mass: 76.6 ± 7.8 kg; [Formula: see text]: 4.3 ± 0.6 L∙min-1) completed four trials on an electromagnetically-braked cycle ergometer. Each trial consisted of a six-stage incremental test (3 minute stages) followed by 30 minutes of passive recovery. One hour before trials 2-4, participants ingested a capsule containing 5 mg∙kg-1 of either caffeine or placebo (maltodextrin). Trials 2 and 3 were designed to evaluate the effects of caffeine on various physiological responses during exercise and recovery. In contrast, Trial 4 was designed to evaluate the effects of caffeine on [BLa] during passive recovery from an end-exercise concentration of 4 mmol∙L-1. Relative to placebo, caffeine increased [BLa] during exercise, independent of exercise intensity (mean difference: 0.33 ± 0.41 mmol∙L-1; 95% likely range: 0.11 to 0.55 mmol∙L-1), but did not affect the time-course of [BLa] during recovery (p = 0.604). Caffeine reduced ratings of perceived exertion (mean difference: 0.5 ± 0.7; 95% likely range: 0.1 to 0.9) and heart rate (mean difference: 3.6 ± 4.2 b∙min-1; 95% likely range: 1.3 to 5.8 b∙min-1) during exercise, with the effect on the latter dissipating as exercise intensity increased. Supplement × exercise intensity interactions were observed for respiratory exchange ratio (p = 0.004) and minute ventilation (p = 0.034). The results of the present study illustrate the clear, though often subtle, effects of caffeine on physiological responses to submaximal exercise. Researchers should be aware of these responses, particularly when evaluating the physiological effects of various experimental interventions.

  18. A New Submaximal Rowing Test to Predict 2,000-m Rowing Ergometer Performance.

    Science.gov (United States)

    Otter, Ruby T A; Brink, Michel S; Lamberts, Robert P; Lemmink, Koen A P M

    2015-09-01

    The purpose of this study was to assess predictive value of a new submaximal rowing test (SmRT) on 2,000-m ergometer rowing time-trial performance in competitive rowers. In addition, the reliability of the SmRT was investigated. Twenty-four competitive male rowers participated in this study. After determining individual HRmax, all rowers performed an SmRT followed by a 2,000-m rowing ergometer time trial. In addition, the SmRT was performed 4 times (2 days in between) to determine the reliability. The SmRT consists of two 6-minute stages of rowing at 70 and 80% HRmax, followed by a 3-minute stage at 90% HRmax. Power was captured during the 3 stages, and 60 seconds of heart rate recovery (HRR60s) was measured directly after the third stage. Results showed that predictive value of power during the SmRT on 2,000-m rowing time also increased with stages. CVTEE% is 2.4, 1.9, and 1.3%. Pearson correlations (95% confidence interval [95% CI]) were -0.73 (-0.88 to -0.45), -0.80 (-0.94 to -0.67), and -0.93 (-0.97 to -0.84). 2,000-m rowing time and HRR60s showed no relationship. Reliability of power during the SmRT improved with the increasing intensity of the stages. The coefficient of variation (CVTEM%) was 9.2, 5.6, and 0.4%. Intraclass correlation coefficients (ICC) and 95% CI were 0.91 (0.78-0.97), 0.92 (0.81-0.97), and 0.99 (0.97-1.00). The CVTEM% and ICC of HRR60s were 8.1% and 0.93 (0.82-0.98). In conclusion, the data of this study shows that the SmRT is a reliable test that it is able to accurately predict 2,000-m rowing time on an ergometer. The SmRT is a practical and valuable submaximal test for rowers, which can potentially assist with monitoring, fine-tuning and optimizing training prescription in rowers.

  19. Several submaximal exercise tests are reliable, valid and acceptable in people with chronic pain, fibromyalgia or chronic fatigue: a systematic review

    Directory of Open Access Journals (Sweden)

    Julia Ratter

    2014-09-01

    [Ratter J, Radlinger L, Lucas C (2014 Several submaximal exercise tests are reliable, valid and acceptable in people with chronic pain, fibromyalgia or chronic fatigue: a systematic review. Journal of Physiotherapy 60: 144–150

  20. Evaluation of Exercise Response in a Young, High Risk Population: Submaximal Invasive Cardiopulmonary Exercise Testing (ICPET) in Active Duty Soldiers

    Science.gov (United States)

    2017-03-17

    Submaximal Invasive Cardiopulmonary Exercise Testing iCPET in AD Soldiers presented at/published to American College of Cardiology’s 661h Annual...disclaimer statement for research involving animals . as required by AFMAN 40-401 IP : " The experiments reported herein were conducted according to the...principles set forth in the National Institute of Health Publication No. 80-23, Guide for the Care and Use of Laboratory Animals and the Animal

  1. Application of "living high-training low" enhances cardiac function and skeletal muscle oxygenation during submaximal exercises in athletes.

    Science.gov (United States)

    Park, Hun-Young; Nam, Sang-Seok

    2017-03-31

    The aim of this study was to determine the efficiency of the application of living high-training low (LHTL) on cardiac function and skeletal muscle oxygenation during submaximal exercises compared with that of living low-training low (LLTL) in athletes. Male middle- and long-distance runners (n = 20) were randomly assigned into the LLTL group (n = 10, living at 1000-m altitude and training at 700-1330-m altitude) and the LHTL group (n = 10, living at simulated 3000-m altitude and training at 700-1330-m altitude). Their cardiac function and skeletal muscle oxygenation during submaximal exercises at sea level before and after training at each environmental condition were evaluated. There was a significant interaction only in the stroke volume (SV); however, the heart rate (HR), end-diastolic volume (EDV), and end-systolic volume (ESV) showed significant main effects within time; HR and SV significantly increased during training in the LHTL group compared with those in the LLTL group. EDV also significantly increased during training in both groups; however, the LHTL group had a higher increase than the LLTL group. ESV significantly increased during training in the LLTL group. There was no significant difference in the ejection fraction and cardiac output. The skeletal muscle oxygen profiles had no significant differences but improved in the LHTL group compared with those in the LLTL group. LHTL can yield favorable effects on cardiac function by improving the HR, SV, EDV, and ESV during submaximal exercises compared with LLTL in athletes.

  2. Reduced peripheral arterial blood flow with preserved cardiac output during submaximal bicycle exercise in elderly heart failure

    Directory of Open Access Journals (Sweden)

    Leng Xiaoyan

    2009-11-01

    Full Text Available Abstract Background Older heart failure (HF patients exhibit exercise intolerance during activities of daily living. We hypothesized that reduced lower extremity blood flow (LBF due to reduced forward cardiac output would contribute to submaximal exercise intolerance in older HF patients. Methods and Results Twelve HF patients both with preserved and reduced left ventricular ejection fraction (LVEF (aged 68 ± 10 years without large (aorta or medium sized (iliac or femoral artery vessel atherosclerosis, and 13 age and gender matched healthy volunteers underwent a sophisticated battery of assessments including a peak exercise oxygen consumption (peak VO2, b physical function, c cardiovascular magnetic resonance (CMR submaximal exercise measures of aortic and femoral arterial blood flow, and d determination of thigh muscle area. Peak VO2 was reduced in HF subjects (14 ± 3 ml/kg/min compared to healthy elderly subjects (20 ± 6 ml/kg/min (p = 0.01. Four-meter walk speed was 1.35 ± 0.24 m/sec in healthy elderly verses 0.98 ± 0.15 m/sec in HF subjects (p p ≤ 0.03. Conclusion During CMR submaximal bike exercise in the elderly with heart failure, mechanisms other than low cardiac output are responsible for reduced lower extremity blood flow.

  3. Effects of Submaximal Endurance Training and Vitamin D3 Supplementation on Pain Threshold in Diabetic Rats

    Directory of Open Access Journals (Sweden)

    S. Jalal Taherabadi

    2013-07-01

    Full Text Available Background: According to beneficial effects of endurance training and vitamin D3 in diabetes mellitus, purpose of this study is effects submaximal endurance training and vitamin D3 supplementation on pain threshold in streptozotocin induced diabetic rats.Materials and Methods: Male Wistar rats (250±20 g, N=40 were made diabetic by streptozotocin (60 mg/kg, subcutaneously. 72 h after injection diabetes induction was confirmed by tail vein blood glucose concentration (>300 mg/dl. Then animals were divided to five groups: diabetic control (DC, diabetic trained (DT, diabetic -vitamin D (DD, diabetic trained and vitamin D (DTD, and control (C. Animals were submitted to endurance training by treadmill and vitamin D3 treatment (twice aweek, intrapretonally for 4 weeks. 48 h after at the end of exercise and treatment protocol, we used tail-flick to assess the effects of training and vitamin D3 on thermal pain threshold. We used one way ANOVA statistical analysis to compare differences between groups, significance level of p<0.05 was considered.Results: Diabetic induced hyperalgesia were decreased significantly by vitamin D but not 4 weeks endurance exercise training. Concurrent effects of training and vitamin D on thermal pain threshold were not significantly higher than vitamin D effects alone.Conclusion: It is concluded that vitamin D administration given at the time of diabetes induction may be able to restore thermal hyperalgesia. But effects of endurance exercise training needs to more investigation in diabetic rats.

  4. "Tailored" submaximal step test for VO2max prediction in healthy older adults.

    Science.gov (United States)

    Pogliaghi, Silvia; Bellotti, Cecilia; Paterson, Donald H

    2014-04-01

    The authors developed and validated a "tailored" version of the Astrand-Rhyming step test (tA-R) and a new equation for VO2max prediction in older adults (OA). Sixty subjects (age 68 ± 4 yr, 30 male, 30 female) performed their tA-R step test (5-min, 30-cm step, tailored stepping rate) and an incremental cycling test to exhaustion. VO2max was (a) predicted using the standard A-R equation (predicted VO2max), (b) predicted based on the authors' new multiple linear equation (equation VO2max), and (c) directly measured by incremental cycling test (direct VO2max). Agreement among values of VO2max was evaluated by Bland-Altman analysis. The predicted VO2max was not significantly different from the direct VO2max, yet with relatively large imprecision. The equation VO2max allowed more precise as well as accurate predictions of VO2max compared with standard A-R prediction. The "tailored" version of the Astrand-Rhyming step test and the new prediction equation appear suitable for a rapid (5-min), safe (submaximal), accurate, and precise VO2max prediction in healthy OA.

  5. Predictability of maximum voluntary isometric knee extension force from submaximal contractions in older adults.

    Science.gov (United States)

    Stackhouse, Scott K; Stevens, Jennifer E; Johnson, Christopher D; Snyder-Mackler, Lynn; Binder-Macleod, Stuart A

    2003-01-01

    The purposes of this study were to develop and test a model describing the relationship between the central activation ratio (CAR; a measure of voluntary muscle activation) and percent maximum voluntary contraction (%MVC) force for old adults and to provide a method for more accurate determination of voluntary muscle activation failure. Twenty-one adults (ages 64-81) performed isometric testing of the quadriceps at 25%, 50%, 75%, and 100% MVC. During each contraction, a 100-HZ, 120-ms train of electrical pulses was delivered to the quadriceps muscle to quantify voluntary muscle activation. Similar to a young, healthy population (ages 20-35), a curvilinear relationship existed between the CAR and %MVC force for older adults. Predictions of subjects' MVCs using the linear model of CAR-%MVC force relationship generally demonstrated poor agreement with actual MVCs. Predictions of MVC from submaximal contractions (25%, 50%, and 75%) using a previously identified curvilinear young adult CAR-%MVC relationship were good [ICC (2,1): 0.81, 0.96, and 0.82, respectively]. Similar agreement was obtained from the curvilinear older adult CAR-%MVC relationship. These data suggest that the CAR-%MVC relationship is similar in young and older adult subjects and that curvilinear models of this relationship can predict MVC forces in older adults more accurately. Reexamination of the relationship between the CAR and %MVC force may allow a more accurate determination of how failure of voluntary muscle activation contributes to weakness in old adults.

  6. Live high:train low increases muscle buffer capacity and submaximal cycling efficiency.

    Science.gov (United States)

    Gore, C J; Hahn, A G; Aughey, R J; Martin, D T; Ashenden, M J; Clark, S A; Garnham, A P; Roberts, A D; Slater, G J; McKenna, M J

    2001-11-01

    This study investigated whether hypoxic exposure increased muscle buffer capacity (beta(m)) and mechanical efficiency during exercise in male athletes. A control (CON, n=7) and a live high:train low group (LHTL, n=6) trained at near sea level (600 m), with the LHTL group sleeping for 23 nights in simulated moderate altitude (3000 m). Whole body oxygen consumption (VO2) was measured under normoxia before, during and after 23 nights of sleeping in hypoxia, during cycle ergometry comprising 4 x 4-min submaximal stages, 2-min at 5.6 +/- 0.4 W kg(-1), and 2-min 'all-out' to determine total work and VO(2peak). A vastus lateralis muscle biopsy was taken at rest and after a standardized 2-min 5.6 +/- 0.4 W kg(-1) bout, before and after LHTL, and analysed for beta(m) and metabolites. After LHTL, beta(m) was increased (18%, P buffer capacity. Further, reduced VO2 during normoxic exercise after LHTL suggests that improved exercise efficiency is a fundamental adaptation to LHTL.

  7. Stability Ball Sitting versus Chair Sitting During Sub-maximal Arm Ergometry.

    Science.gov (United States)

    Marks, Charles R C; Hylland, Kristina E; Terrell, Jacob

    It was predicted that sitting on a stability ball during arm ergometry would elevate cardiovascular parameters when compared to sitting on a chair and that this would be associated with greater recruitment of trunk and leg skeletal muscles. Open-circuit spirometry, videotaping, blood pressure, heart rate, and EMG were conducted during rest and four minute stages of 15 W, 30 W, and 45 W using a Monark arm ergometer. Twenty-six apparently healthy adults exercised twice, once sitting on a stability ball and the other sitting on a chair (order randomized), with 45 to 60 minutes of rest between. ANOVA for repeated measures and paired-t testing were used for analysis. Oxygen consumption was significantly 10 to 16% higher during exercise while sitting on the stability ball. There were no significant differences between sitting modes for heart rate, SBP, and DBP. Also, resting and exercise rectus femoris and 45 W external oblique EMGs were significantly higher on the stability ball. Finally, the knee was significantly more extended with the feet farther apart and more forward on the stability ball. The stability ball significantly elevates oxygen consumption during sub-maximal arm cranking without significantly increasing heart rate or blood pressure and this is associated with increased thigh muscle activation and lower leg repositioning.

  8. Is the ventilatory threshold coincident with maximal fat oxidation during submaximal exercise in women?

    Science.gov (United States)

    Astorino, T A

    2000-09-01

    The purpose of this study was to detect the fraction of peak oxygen consumption (VO2peak) that elicits maximal rates of fat oxidation during submaximal treadmill exercise. It was hypothesized that this point would appear at a work rate just below the ventilatory threshold. subjects completed a protocol requiring them to exercise for 15 min on a treadmill at six different workloads, 25, 40, 55, 65, 75, and 85% VO2peak, over two separate visits. nine healthy, moderately-trained eumenorrheic females (age = 28.8+/-5.99 yrs, VO2peak = 47.20 +/-2.57 ml x kg(-1) x min(-1)) volunteered for the study. a one-way ANOVA with repeated measures was used to test for differences across exercise intensities in the metabolic variables (i.e. substrate oxidation, blood lactate concentration ([La-]), RER, and the contribution of fat to total energy expenditure). Following significant F ratios, post-hoc tests were used to detect differences between the means for various exercise intensities. Exercise at 75% VO2peak elicited the greatest rate of fat oxidation (4.75+/-0.49 kcal x min(-1)), and this intensity was coincident with the ventilatory threshold (76+/-7.41% VO2peak). Moreover, a significant difference (t(8) = -3.98, ppopulation has application in exercise prescription and refutes the belief that low-intensity exercise is preferred for fat metabolism.

  9. Acute Warm-up Effects in Submaximal Athletes: An EMG Study of Skilled Violinists.

    Science.gov (United States)

    McCrary, J Matt; Halaki, Mark; Sorkin, Evgeny; Ackermann, Bronwen J

    2016-02-01

    Warm-up is commonly recommended for injury prevention and performance enhancement across all activities, yet this recommendation is not supported by evidence for repetitive submaximal activities such as instrumental music performance. The objective of this study is to quantify the effects of cardiovascular, core muscle, and musical warm-ups on muscle activity levels, musical performance, and subjective experience in skilled violinists. Fifty-five undergraduate, postgraduate, or professional violinists performed five randomly ordered 45-s musical excerpts of varying physical demands both before and after a randomly assigned 15-min, moderate-intensity cardiovascular, core muscle, musical (technical violin exercises), or inactive control warm-up protocol. Surface EMG data were obtained for 16 muscles of the trunk, shoulders, and right arm during each musical performance. Sound recording and perceived exertion (RPE) data were also obtained. Sound recordings were randomly ordered and rated for performance quality by blinded adjudicators. Questionnaire data regarding participant pain sites and fitness levels were used to stratify participants according to pain and fitness levels. Data were analyzed using two- and three-factor ANCOVA (surface EMG and sound recording) and Wilcoxon matched pairs tests (RPE). None of the three warm-up protocols had significant effects on muscle activity levels (P ≥ 0.10). Performance quality did not significantly increase (P ≥ 0.21). RPE significantly decreased (P 0.23). Acute physiological and musical benefits from cardiovascular, core muscle, and musical warm-ups in skilled violinists are limited to decreases in RPE. This investigation provides data from the performing arts in support of sports medical evidence suggesting that warm-up only effectively enhances maximal strength and power performance.

  10. Cortical and spinal mechanisms of task failure of sustained submaximal fatiguing contractions.

    Directory of Open Access Journals (Sweden)

    Petra S Williams

    Full Text Available In this and the subsequent companion paper, results are presented that collectively seek to delineate the contribution that supraspinal circuits have in determining the time to task failure (TTF of sustained submaximal contractions. The purpose of this study was to compare adjustments in supraspinal and spinal excitability taken concurrently throughout the performance of two different fatigue tasks with identical mechanical demands but different TTF (i.e., force-matching and position-matching tasks. On separate visits, ten healthy volunteers performed the force-matching or position-matching task at 15% of maximum strength with the elbow flexors to task failure. Single-pulse transcranial magnetic stimulation (TMS, paired-pulse TMS, paired cortico-cervicomedullary stimulation, and brachial plexus electrical stimulation were delivered in a 6-stimuli sequence at baseline and every 2-3 minutes throughout fatigue-task performance. Contrary to expectations, the force-matching task TTF was 42% shorter (17.5 ± 7.9 min than the position-matching task (26.9 ± 15.11 min; p0.05. Therefore, failure occurred after a similar mean decline in motorneuron excitability developed (p0.10 and an index of upstream excitation of the motor cortex remained constant (p>0.40. Together, these results suggest that as fatigue develops prior to task failure, the increase in corticospinal excitability observed in relationship to the decrease in spinal excitability results from a combination of decreasing intracortical inhibition with constant levels of intracortical facilitation and upstream excitability that together eventually fail to provide the input to the motor cortex necessary for descending drive to overcome the spinal cord resistance, thereby contributing to task failure.

  11. Cortical and Spinal Mechanisms of Task Failure of Sustained Submaximal Fatiguing Contractions

    Science.gov (United States)

    Williams, Petra S.; Hoffman, Richard L.; Clark, Brian C.

    2014-01-01

    In this and the subsequent companion paper, results are presented that collectively seek to delineate the contribution that supraspinal circuits have in determining the time to task failure (TTF) of sustained submaximal contractions. The purpose of this study was to compare adjustments in supraspinal and spinal excitability taken concurrently throughout the performance of two different fatigue tasks with identical mechanical demands but different TTF (i.e., force-matching and position-matching tasks). On separate visits, ten healthy volunteers performed the force-matching or position-matching task at 15% of maximum strength with the elbow flexors to task failure. Single-pulse transcranial magnetic stimulation (TMS), paired-pulse TMS, paired cortico-cervicomedullary stimulation, and brachial plexus electrical stimulation were delivered in a 6-stimuli sequence at baseline and every 2–3 minutes throughout fatigue-task performance. Contrary to expectations, the force-matching task TTF was 42% shorter (17.5±7.9 min) than the position-matching task (26.9±15.11 min; pmuscle fatigue (p = 0.59). There were no task-specific differences for the total amount or rate of change in the neurophysiologic outcome variables over time (p>0.05). Therefore, failure occurred after a similar mean decline in motorneuron excitability developed (p0.10) and an index of upstream excitation of the motor cortex remained constant (p>0.40). Together, these results suggest that as fatigue develops prior to task failure, the increase in corticospinal excitability observed in relationship to the decrease in spinal excitability results from a combination of decreasing intracortical inhibition with constant levels of intracortical facilitation and upstream excitability that together eventually fail to provide the input to the motor cortex necessary for descending drive to overcome the spinal cord resistance, thereby contributing to task failure. PMID:24667484

  12. TEST-RETEST RELIABILITY OF THE AEROBIC POWER INDEX SUBMAXIMAL EXERCISE TEST IN CANCER PATIENTS

    Directory of Open Access Journals (Sweden)

    Bonnie J. Furzer

    2012-12-01

    Full Text Available The purpose of this study was to investigate the reliability of the Aerobic Power Index (API submaximal cardiorespiratory exercise test, as well as associated variables of oxygen uptake (ml·kg-1·min-1 and ratings of perceived exertion (RPE in cancer patients who are generally unable to complete maximal or lengthy aerobic fitness tests. Twenty male and female participants (11 male; 9 female aged between 18 and 70 y (mean = 53.28 ± 11. 82 y were recruited with medical consent within 4 weeks of completing chemotherapy treatment for a lymphohaematopoietic cancer (LHC. Of the twenty recruited participants' 2 were excluded from analysis due to disease relapse or complications unrelated to testing occurring within the month following testing. Intra-class correlation coefficient (ICC scores for power output (W·kg-1 and oxygen uptake (ml·kg-1·min-1 were highly reliable (R1 = 0.96 and 0.96, respectively and the ICC for RPE was moderately reliable (R1 = 0.83. Technical error of measurement results for power output (W·kg-1, oxygen uptake (ml·kg-1·min-1 and RPE were 0.11W·kg-1, 1.18 ml·kg-1·min-1 and 1.0 respectively. A Pearson's product-moment correlation demonstrated a strong relationship between power output (W·kg-1 and oxygen uptake (ml·kg-1·min-1 for both trials (r = 0.93 and 0.89, respectively. Results demonstrate that the API test is a highly reliable protocol for use with a LHC population and can be considered a clinically feasible, safe and tolerable exercise test

  13. A submaximal test for the assessment of knee extensor endurance capacity.

    Science.gov (United States)

    De Ruiter, Cornelis J; Mallee, Max I P; Leloup, Lara E C; De Haan, Arnold

    2014-02-01

    We aimed to develop an undemanding test for endurance capacity of the knee extensor muscles, which can also be applied to frail participants. We hypothesized 1) that the first objective indications for peripheral fatigue during incremental unilateral repetitive isometric knee extensor contractions could be used to assess a fatigue threshold (FT), 2) that torque at FT would depend on training status, and 3) that this torque could easily be sustained for 30 min. Five trained and five untrained participants performed 5-min bouts of 60 repetitive contractions (3-s on and 2-s off). Torque, set at 25% maximal voluntary contraction (MVC), was increased by 5% MVC in subsequent bouts. The highest torque for which rectified surface EMG remained stable during the bout was defined as the FT. On separate occasions, 30-min bouts were performed at and above the FT to assess sustainable torque. Changes in gas exchange parameters, HR, and RPE were monitored to corroborate FT. At FT (RPE = 5.7 ± 1.7), torque was higher (P MVC) than in untrained participants (30.5% ± 1.8% MVC). Sustainable torque was ∼4% higher than (P MVC, significant increases in rectified surface EMG and V˙O2 were found. During incremental knee extensor contractions, FT could be assessed at a submaximal exercise intensity. FT was higher in trained than in untrained participants and was related to exercise sustainability. With the use of FT, changes in endurance capacity of single muscle groups can potentially also be determined in frail participants for whom exercise performed until exhaustion is unwarranted.

  14. The Effect of Acute Sub-Maximal Endurance Exercise on Serum Angiogenic Indices in Sedentary Men

    Directory of Open Access Journals (Sweden)

    Kamal Ranjbar

    2014-06-01

    Full Text Available Background: Endurance training increases capillary density of skeletal muscle, but the molecular mechanism of this process is not yet clear. Therefore, the purpose of this study was to investigate the effect of acute sub maximal endurance exercise on serum levels of vascular endothelial growth factor (VEGF and matrix metaloproteinases 2 and 9 (MMP-2 and MMP-9 in sedentary men. Materials and Methods: Twelve healthy men (22.37±2.30 years, BMI=23.16 ±2.61 kg/mP 2 P participated in this study. Subjects exercised for 1h at 70% of VOR2R max, 3 days after the VOR2R max determination. Antecubital vein blood was collected at rest, immediately and 2h after the exercise. Serum VEGF, MMP-2 and MMP-9 were measured by ELISA methods5T. Results: Serum levels of VEGF and MMP-2 decreased immediately after the exercise. 2 hours after the exercise, serum levels of VEGF remained at a lower level but serum MMP-2 returned to its basal level. Also, serum levels of MMP-9 did not change significantly in response to exercise5T. Conclusion: Acute sub-maximal endurance exercise decreased the main factors involved in development of capillary density in sedentary men. This might to due to the fact that, sub maximal exercise could not provide the two main stimulating factors of angiogenesis, i.e. Shear stress and hypoxia. It could also be explained by the fact that the mechanism of development of capillary network following regular endurance training is different from that following an acute exercise5T.5T

  15. Different types of compression clothing do not increase sub-maximal and maximal endurance performance in well-trained athletes.

    Science.gov (United States)

    Sperlich, Billy; Haegele, Matthias; Achtzehn, Silvia; Linville, John; Holmberg, Hans-Christer; Mester, Joachim

    2010-04-01

    Three textiles with increasing compressive surface were compared with non-compressive conventional clothing on physiological and perceptual variables during sub-maximal and maximal running. Fifteen well-trained endurance athletes (mean+/-s: age 27.1+/-4.8 years, VO(2max) 63.7+/-4.9 ml x min(-1) x kg(-1)) performed four sub-maximal (approximately 70% VO(2max)) and maximal tests with and without different compression stockings, tights, and whole-body compression suits. Arterial lactate concentration, oxygen saturation and partial pressure, pH, oxygen uptake, and ratings of muscle soreness were recorded before, during, and after all tests. In addition, we assessed time to exhaustion. Sub-maximal (P=0.22) and maximal oxygen uptake (P=0.26), arterial lactate concentration (P=0.16; 0.20), pH (P=0.23; 0.46), oxygen saturation (P=0.13; 0.26), and oxygen partial pressure (P=0.09; 0.20) did not differ between the types of clothing (effect sizes=0.00-0.45). Ratings of perceived exertion (P=0.10; 0.15), muscle soreness (P=0.09; 0.10) and time to exhaustion (P=0.16) were also unaffected by the different clothing (effect sizes=0.28-0.85). This was the first study to evaluate the effect on endurance performance of different types of compression clothing with increasing amounts of compressive surface. Overall, there were no performance benefits when using the compression garments.

  16. Comparing the Effects of Rest and Massage on Return to Homeostasis Following Submaximal Aerobic Exercise: a Case Study.

    Science.gov (United States)

    Resnick, Portia B

    2016-03-01

    Postexercise massage can be used to help promote recovery from exercise on the cellular level, as well as systemically by increasing parasympathetic activity. No studies to date have been done to assess the effects of massage on postexercise metabolic changes, including excess postexercise oxygen consumption (EPOC). The purpose of this study was to compare the effects of massage recovery and resting recovery on a subject's heart rate variability and selected metabolic effects following a submaximal treadmill exercise session. One healthy 24-year-old female subject performed 30 minutes of submaximal treadmill exercise prior to resting or massage recovery sessions. Metabolic data were collected throughout the exercise sessions and at three 10 minute intervals postexercise. Heart rate variability was evaluated for 10 minutes after each of two 30-minute recovery sessions, either resting or massage. Heart rate returned to below resting levels (73 bpm) with 30 and 60 minutes of massage recovery (72 bpm and 63 bpm, respectively) compared to 30 and 60 minutes of resting recovery (77 bpm and 74 bpm, respectively). Heart rate variability data showed a more immediate shift to the parasympathetic state following 30 minutes of massage (1.152 LF/HF ratio) versus the 30-minute resting recovery (6.91 LF/HF ratio). It took 60 minutes of resting recovery to reach similar heart rate variability levels (1.216 LF/HF) found after 30 minutes of massage. Ventilations after 30 minutes of massage recovery averaged 7.1 bpm compared to 17.9 bpm after 30 minutes of resting recovery. No differences in EPOC were observed through either the resting or massage recovery based on the metabolic data collected. Massage was used to help the subject shift into parasympathetic activity more quickly than rest alone following a submaximal exercise session.

  17. Comparing the Effects of Rest and Massage on Return to Homeostasis Following Submaximal Aerobic Exercise: a Case Study

    Science.gov (United States)

    Resnick, Portia B.

    2016-01-01

    Introduction Postexercise massage can be used to help promote recovery from exercise on the cellular level, as well as systemically by increasing parasympathetic activity. No studies to date have been done to assess the effects of massage on postexercise metabolic changes, including excess postexercise oxygen consumption (EPOC). The purpose of this study was to compare the effects of massage recovery and resting recovery on a subject’s heart rate variability and selected metabolic effects following a submaximal treadmill exercise session. Methods One healthy 24-year-old female subject performed 30 minutes of submaximal treadmill exercise prior to resting or massage recovery sessions. Metabolic data were collected throughout the exercise sessions and at three 10 minute intervals postexercise. Heart rate variability was evaluated for 10 minutes after each of two 30-minute recovery sessions, either resting or massage. Results Heart rate returned to below resting levels (73 bpm) with 30 and 60 minutes of massage recovery (72 bpm and 63 bpm, respectively) compared to 30 and 60 minutes of resting recovery (77 bpm and 74 bpm, respectively). Heart rate variability data showed a more immediate shift to the parasympathetic state following 30 minutes of massage (1.152 LF/HF ratio) versus the 30-minute resting recovery (6.91 LF/HF ratio). It took 60 minutes of resting recovery to reach similar heart rate variability levels (1.216 LF/HF) found after 30 minutes of massage. Ventilations after 30 minutes of massage recovery averaged 7.1 bpm compared to 17.9 bpm after 30 minutes of resting recovery. Conclusions No differences in EPOC were observed through either the resting or massage recovery based on the metabolic data collected. Massage was used to help the subject shift into parasympathetic activity more quickly than rest alone following a submaximal exercise session. PMID:26977215

  18. Submaximal cardiopulmonary thresholds on a robotics-assisted tilt table, a cycle and a treadmill: a comparative analysis.

    Science.gov (United States)

    Saengsuwan, Jittima; Nef, Tobias; Laubacher, Marco; Hunt, Kenneth J

    2015-11-10

    The robotics-assisted tilt table (RATT), including actuators for tilting and cyclical leg movement, is used for rehabilitation of severely disabled neurological patients. Following further engineering development of the system, i.e. the addition of force sensors and visual bio-feedback, patients can actively participate in exercise testing and training on the device. Peak cardiopulmonary performance parameters were previously investigated, but it also important to compare submaximal parameters with standard devices. The aim of this study was to evaluate the feasibility of the RATT for estimation of submaximal exercise thresholds by comparison with a cycle ergometer and a treadmill. 17 healthy subjects randomly performed six maximal individualized incremental exercise tests, with two tests on each of the three exercise modalities. The ventilatory anaerobic threshold (VAT) and respiratory compensation point (RCP) were determined from breath-by-breath data. VAT and RCP on the RATT were lower than the cycle ergometer and the treadmill: oxygen uptake (V'O2) at VAT was [mean (SD)] 1.2 (0.3), 1.5 (0.4) and 1.6 (0.5) L/min, respectively (p < 0.001); V'O2 at RCP was 1.7 (0.4), 2.3 (0.8) and 2.6 (0.9) L/min, respectively (p = 0.001). High correlations for VAT and RCP were found between the RATT vs the cycle ergometer and RATT vs the treadmill (R on the range 0.69-0.80). VAT and RCP demonstrated excellent test-retest reliability for all three devices (ICC from 0.81 to 0.98). Mean differences between the test and retest values on each device were close to zero. The ventilatory equivalent for O2 at VAT for the RATT and cycle ergometer were similar and both were higher than the treadmill. The ventilatory equivalent for CO2 at RCP was similar for all devices. Ventilatory equivalent parameters demonstrated fair-to-excellent reliability and repeatability. It is feasible to use the RATT for estimation of submaximal exercise thresholds: VAT and RCP on the RATT were lower than the

  19. Evaluation of the American College of Sports Medicine submaximal treadmill running test for predicting VO2max.

    Science.gov (United States)

    Marsh, Clare E

    2012-02-01

    The purpose of this study was to assess the validity of the American College of Sports Medicine's (ACSM's) submaximal treadmill running test in predicting VO2max. Twenty-one moderately well-trained men aged 18-34 years performed 1 maximal treadmill test to determine maximal oxygen uptake (M VO2max) and 2 submaximal treadmill tests using 4 stages of continuous submaximal exercise. Estimated VO2max was predicted by extrapolation to age-predicted maximal heart rate (HRmax) and calculated in 2 ways: using data from all submaximal stages between 110 b·min(-1) and 85% HRmax (P VO2max-All), and using data from the last 2 stages only (P VO2max-2). The measured VO2max was overestimated by 3% on average for the group but was not significantly different to predicted VO2max (1-way analysis of variance [ANOVA] p = 0.695; M VO2max = 53.01 ± 5.38; P VO2max-All = 54.27 ± 7.16; P VO2max-2 = 54.99 ± 7.69 ml·kg(-1)·min(-1)), although M VO2max was not overestimated in all the participants--it was underestimated in 30% of observations. Pearson's correlation, standard error of estimate (SEE), and total error (E) between measured and predicted VO2max were r = 0.646, 4.35, 4.08 ml·kg(-1)·min(-1) (P VO2max-All) and r = 0.642, 4.21, 3.98 ml·kg(-1)·min(-1) (P VO2max-2) indicating that the accuracy in prediction (error) was very similar whether using P VO2max-All or P VO2max-2, with up to 70% of the participants predicted scores within 1 SEE (∼4 ml·kg(-1)·min(-1)) of M VO2max. In conclusion, the ACSM equation provides a reasonably good estimation of VO2max with no difference in predictive accuracy between P VO2max-2 and P VO2max-All, and hence, either approach may be equally useful in tracking an individual's aerobic fitness over time. However, if a precise knowledge of VO2max is required, then it is recommended that this be measured directly.

  20. Substrate utilization during submaximal exercise in children with a severely obese parent

    Directory of Open Access Journals (Sweden)

    Eaves Audrey D

    2012-05-01

    Full Text Available Abstract Background We have reported a reduction in fatty acid oxidation (FAO at the whole-body level and in skeletal muscle in severely obese (BMI ≥ 40 kg/m2 individuals; this defect is retained in cell culture suggesting an inherent component. The purpose of the current study was to determine if an impairment in whole-body fatty acid oxidation (FAO was also evident in children with a severely obese parent. Methods Substrate utilization during submaximal exercise (cycle ergometer was determined in children ages 8–12 y with a severely obese parent (OP, n = 13 or two lean/non-obese (BMI range of 18 to 28 kg/m2 parents (LP, n = 13. A subgroup of subjects (n = 3/group performed 4 weeks of exercise training with substrate utilization measured after the intervention. Results The children did not differ in age (LP vs. OP, respectively (10.7 ± 0.5 vs. 10.2 ± 0.5 y, BMI percentile (65.3 ± 5.2 vs. 75.9 ± 7, Tanner Stage (1.4 ± 0.2 vs. 1.5 ± 0.2, VO2peak (40.3 ± 2.7 vs. 35.6 ± 2.6 ml/kg/min or physical activity levels (accelerometer. At the same absolute workload of 15 W (~38% VO2peak, RER was significantly (P ≤ 0.05 lower in LP vs. OP (0.83 ± 0.02 vs. 0.87 ± 0.01 which was reflected in a reduced reliance on FAO for energy production in the OP group (58.6 ± 5.1 vs. 43.1 ± 4.0% of energy needs during exercise from FAO. At a higher exercise intensity (~65% VO2peak there were no differences in substrate utilization between LP and OP. After exercise training RER tended to decrease (P = 0.06 at the 15 W workload, suggesting an increased reliance on FAO regardless of group. Conclusions These findings suggest that the decrement in FAO with severe obesity has an inherent component that may be overcome with exercise training.

  1. Analysing visual pattern of skin temperature during submaximal and maximal exercises

    Science.gov (United States)

    Balci, Gorkem Aybars; Basaran, Tahsin; Colakoglu, Muzaffer

    2016-01-01

    Aims of this study were to examine our hypotheses assuming that (a) skin temperature patterns would differ between submaximal exercise (SE) and graded maximal exercise test (GXT) and (b) thermal kinetics of Tskin occurring in SE and GXT might be similar in a homogenous cohort. Core temperature (Tcore) also observed in order to evaluate thermoregulatory responses to SE and GXT. Eleven moderately to well-trained male athletes were volunteered for the study (age: 22.2 ± 3.7 years; body mass: 73.8 ± 6.9 kg; height: 181 ± 6.3 cm; body surface area 1.93 ± 0.1 m2; body fat: 12.6% ± 4.2%; V ˙ O2max: 54 ± 9.9 mL min-1 kg-1). Under stabilized environmental conditions in climatic chamber, GXT to volitional exhaustion and 20-min SE at 60% of VO2max were performed on cycle ergometer. Thermal analyses were conducted in 2-min intervals throughout exercise tests. Tskin was monitored by a thermal camera, while Tcore was recorded via an ingestible telemetric temperature sensor. Thermal kinetic analyses showed that Tskin gradually decreased till the 7.58 ± 1.03th minutes, and then initiated to increase till the end of SE (Rsqr = 0.97), while Tskin gradually decreased throughout the GXT (Rsqr = 0.89). Decrease in the level of Tskin during the GXT was significantly below from the SE [F (4, 40) = 2.67, p = 0.07, ηp2 = 0.211]. In the meantime, Tcore continuously increased throughout the SE and GXT (p 0.05). However, total heat energies were calculated as 261.5 kJ/m2 and 416 kJ/m2 for GXT and SE, respectively (p exercises as expected. Tskin curves patterns found to be associated amongst participants at both GXT and SE. Therefore, Tskin kinetics may ensure an important data for monitoring thermoregulation in exercise.

  2. Gender differences in substrate utilization during submaximal exercise in endurance-trained subjects.

    Science.gov (United States)

    Roepstorff, Carsten; Steffensen, Charlotte H; Madsen, Marianne; Stallknecht, Bente; Kanstrup, Inge-Lis; Richter, Erik A; Kiens, Bente

    2002-02-01

    Substrate utilization across the leg during 90 min of bicycle exercise at 58% of peak oxygen uptake (VO(2 peak)) was studied in seven endurance-trained males and seven endurance-trained, eumenorrheic females by applying arteriovenous catheterization, stable isotopes, and muscle biopsies. The female and male groups were matched according to VO(2 peak) per kilogram of lean body mass, physical activity level, and training history of the subjects. All subjects consumed the same diet, well controlled in terms of nutrient composition as well as energy content, for 8 days preceding the experiment, and all females were tested in the midfollicular phase of the menstrual cycle. During exercise, respiratory exchange ratio (RER) and leg respiratory quotient (RQ) were similar in females and males. Myocellular triacylglycerol (TG) degradation was negligible in males but amounted to 12.4 +/- 3.2 mmol/kg dry wt in females and corresponded to 25.0 +/- 6.0 and 5.0 +/- 7.3% of total oxygen uptake in females and males, respectively (P < 0.05). Utilization of plasma fatty acids (12.0 +/- 2.5 and 9.6 +/- 1.5%), blood glucose (13.6 +/- 1.5 and 14.3 +/- 1.5%), and glycogen (48.5 +/- 4.9 and 42.8 +/- 2.1%) were similar in females and males. Thus, in females, measured substrate oxidation accounted for 99% of the leg oxygen uptake, whereas in males 28% of leg oxygen uptake was unaccounted for in terms of measured oxidized lipid substrates. These findings may indicate that males utilized additional lipid sources, presumably very low density lipoprotein-TG or TG located between muscle fibers. On the basis of RER and leg RQ, it is concluded that no gender difference existed in the relative contribution from carbohydrate and lipids to the oxidative metabolism across the leg during submaximal exercise at the same relative workload. However, an effect of gender appears to occur in the utilization of the different lipid sources.

  3. Normobaric Hypoxia and Submaximal Exercise Effects on Running Memory and Mood State in Women.

    Science.gov (United States)

    Seo, Yongsuk; Gerhart, Hayden D; Stavres, Jon; Fennell, Curtis; Draper, Shane; Glickman, Ellen L

    2017-07-01

    An acute bout of exercise can improve cognitive function in normoxic and hypoxic conditions. However, limited research supports the improvement of cognitive function and mood state in women. The purpose of this study was to examine the effects of hypoxia and exercise on working memory and mood state in women. There were 15 healthy women (age = 22 ± 2 yr) who completed the Automated Neuropsychological Assessment Metrics-4th Edition (ANAM), including the Running Memory Continuous Performance Task (RMCPT) and Total Mood Disturbance (TMD) in normoxia (21% O2), at rest in normoxia and hypoxia (12.5% O2), and during cycling exercise at 60% and 40% Vo2max in hypoxia. RMCPT was not significantly impaired at 30 (100.3 ± 17.2) and 60 (96.6 ± 17.3) min rest in hypoxia compared to baseline in normoxia (97.0 ± 17.0). However, RMCPT was significantly improved during exercise (106.7 ± 20.8) at 60% Vo2max compared to 60 min rest in hypoxia. Following 30 (-89.4 ± 48.3) and 60 min of exposure to hypoxia (-79.8 ± 55.9) at rest, TMD was impaired compared with baseline (-107.1 ± 46.2). TMD was significantly improved during exercise (-108.5 ± 42.7) at 40% Vo2max compared with 30 min rest in hypoxia. Also, RMCPT was significantly improved during exercise (104.0 ± 19.1) at 60% Vo2max compared to 60 min rest in hypoxia (96.6 ± 17.3). Hypoxia and an acute bout of exercise partially influence RMCPT and TMD. Furthermore, a moderate-intensity bout of exercise (60%) may be a more potent stimulant for improving cognitive function than low-intensity (40%) exercise. The present data should be considered by aeromedical personnel performing cognitive tasks in hypoxia.Seo Y, Gerhart HD, Stavres J, Fennell C, Draper S, Glickman EL. Normobaric hypoxia and submaximal exercise effects on running memory and mood state in women. Aerosp Med Hum Perform. 2017; 88(7):627-632.

  4. Test retest reliability and minimal detectable change of a novel submaximal graded exercise test in the measurement of graded exercise test duration.

    Science.gov (United States)

    Taylor, James D; Bandy, William D; Whittemore, Joe D

    2011-05-01

    Measurement of graded exercise test duration is clinically important and can be assessed by maximal graded exercise testing. Yet, limitations of maximal graded exercise testing exist. An alternative to maximal graded exercise testing is submaximal graded exercise testing. However, no studies have investigated the reliability of a submaximal graded exercise test in the measurement of graded exercise test duration. The purpose of this study was to determine the test-retest reliability and minimal detectable change (MDC) of a novel submaximal graded exercise test in the measurement of graded exercise test duration. Fifteen people (4 men, 11 women) with a mean age of 26.20 years (SD = 9.04) participated in this study. A novel submaximal graded exercise test was used to measure graded exercise test duration for each participant. Endpoints of the test were either 85% of age-predicted maximum heart rate or voluntarily stopping the test, whichever endpoint occurred first. Heart rate and graded exercise test duration were constantly measured throughout the test. Graded exercise test duration was defined as the total duration (minutes) of the test. For all participants, the submaximal graded exercise test was conducted at baseline and 48-72 hours thereafter. The intraclass correlation coefficient for the test-retest reliability of the test in determining graded exercise test duration was 0.94 (95% CI = 0.83-0.98). The MDC of the test in the measurement of graded exercise test duration was 0.86 minutes. The results suggest that clinicians can use this novel submaximal graded exercise test to reliably measure graded exercise test duration with a measurement error, as expressed by the MDC, of 0.86 minutes.

  5. Isokinetic performance capacity of trunk muscles. Part II: Coefficient of variation in isokinetic measurement in maximal effort and in submaximal effort.

    Science.gov (United States)

    Luoto, S; Hupli, M; Alaranta, H; Hurri, H

    1996-12-01

    It has been claimed that with the aid of isokinetic trunk strength measuring devices it is possible to distinguish true muscular weakness from submaximal effort in the test. This proposition is based on the presumption that in the isokinetic trunk strength test identical performances can only be reproduced by maximal effort. The purpose of this study was to investigate whether it is possible to distinguish maximal effort from submaximal with the aid of the coefficient of variation (CV) in an isokinetic trunk muscle strength test. The study group included 35 (21 male and 14 female) subjects of whom 12 were healthy, 10 had a mild low-back pain and 13 had a more severe chronic low-back pain. The subjects performed five consecutive bendings both with maximal (100%) and submaximal (50%) efforts at a speed of 90 degrees/second. In maximal effort only healthy subjects reached an average level of CV close to 10% both in extension and in flexion. In the chronic low-back pain group the average CV was close to 20%. The difference in CV was statistically significant (p < 0.05-0.02) between the healthy and the chronic low-back pain subjects. In the submaximal effort all health groups had a CV of approximately 20% or more and no significant differences were found. The group of slightly variable measurements (CV = 11-20%) was remarkably large in both the maximal and submaximal effort. The results suggest that an effort with a CV of 11-20% cannot be classified as definitely submaximal or maximal. When the CV is less than 10% the effort can be fairly certainly classified as maximal.

  6. Oxygen uptake efficiency slope, a new submaximal parameter in evaluating exercise capacity in chronic heart failure patients.

    Science.gov (United States)

    Van Laethem, Christophe; Bartunek, Jozef; Goethals, Marc; Nellens, Paul; Andries, Erik; Vanderheyden, Marc

    2005-01-01

    The oxygen uptake efficiency slope (OUES) is a new submaximal parameter which objectively predicts the maximal exercise capacity in children and healthy subjects. However, the usefulness of OUES in adult patients with and without advanced heart failure remains undetermined. The present study investigates the stability and the usefulness of OUES in adult cardiac patients with and without heart failure. Forty-five patients with advanced heart failure (group A) and 35 patients with ischemic heart disease but normal left ventricular ejection fraction (group B) performed a maximal exercise test. PeakVO2 and percentage of predicted peakVO2 were markers of maximal exercise capacity, whereas OUES, ventilatory anaerobic threshold (VAT), and slope VE/VCO2 were calculated as parameters of submaximal exercise. Group A patients had lower peakVO2 (P slope VE/VCO2 (P slope VE/VCO2, and OUES (all P slope VE/VCO2 (r = -.492, P failure patients unable to perform a maximal exercise test. Further studies are needed to confirm our hypothesis.

  7. Comparing VO2max determined by using the relation between heart rate and accelerometry with submaximal estimated VO2max.

    Science.gov (United States)

    Tönis, T M; Gorter, K; Vollenbroek-Hutten, M M R; Hermens, H

    2012-08-01

    An exploratory study to identify parameters that can be used for estimating a subject's cardio-respiratory physical fitness level, expressed as VO2max, from a combination of heart rate and 3D accelerometer data. Data were gathered from 41 healthy subjects (23 male, 18 female) aged between 20 and 29 years. The measurement protocol consisted of a sub-maximal single stage treadmill walking test for VO2max estimation followed by a walking test at two different speeds (4 and 5.5 kmh-1) for parameter determination. The relation between measured heart rate and accelerometer output at different walking speeds was used to get an indication of exercise intensity and the corresponding heart rate at that intensity. Regression analysis was performed using general subject measures (age, gender, weight, length, BMI) and intercept and slope of the relation between heart rate and accelerometer output during walking as independent variables to estimate the VO2max. A linear regression model using a combination of the slope and intercept parameters, together with gender revealed the highest percentage of explained variance (R2 = 0.90) and had a standard error of the estimate (SEE) of 2.052 mL O2kg-1min-1 with VO2max. Results are comparable with current commonly used sub-maximal laboratory tests to estimate VO2max. The combination of heart rate and accelerometer data seems promising for ambulant estimation of VO2max-.

  8. Exposure to a combination of heat and hyperoxia during cycling at submaximal intensity does not alter thermoregulatory responses

    Directory of Open Access Journals (Sweden)

    C Zinner

    2016-02-01

    Full Text Available In this study, we tested the hypothesis that breathing hyperoxic air (FinO2 = 0.40 while exercising in a hot environment exerts negative effects on the total tissue level of haemoglobin concentration (tHb; core (Tcore and skin (Tskin temperatures; muscle activity; heart rate; blood concentration of lactate; pH; partial pressure of oxygen (PaO2 and carbon dioxide; arterial oxygen saturation (SaO2; and perceptual responses. Ten well-trained male athletes cycled at submaximal intensity at 21°C or 33°C in randomized order: first for 20 min while breathing normal air (FinO2 = 0.21 and then 10 min with FinO2 = 0.40 (HOX. At both temperatures, SaO2 and PaO2, but not tHb, were increased by HOX. Tskin and perception of exertion and thermal discomfort were higher at 33°C than 21°C (p 0.07. Blood lactate and heart rate were higher at 33°C than 21°C. In conclusion, during 30 min of submaximal cycling at 21°C or 33°C, Tcore, Tskin and Tbody, tHb, muscle activity and ratings of perceived exertion and thermal discomfort were the same under normoxic and hyperoxic conditions. Accordingly, breathing hyperoxic air (FinO2 = 0.40 did not affect thermoregulation under these conditions.

  9. Regadenoson in Europe: first-year experience of regadenoson stress combined with submaximal exercise in patients undergoing myocardial perfusion scintigraphy.

    Science.gov (United States)

    Brinkert, M; Reyes, E; Walker, S; Latus, K; Maenhout, A; Mizumoto, R; Nkomo, C; Standbridge, K; Wechalekar, K; Underwood, S R

    2014-03-01

    Regadenoson was approved for clinical use in Europe in 2011. Since then, it has become the default form of stress at our institution. We have assessed the side-effect profile and tolerability of regadenoson in patients undergoing clinically indicated myocardial perfusion scintigraphy between July 2011 and July 2012. Clinical, stress and imaging data were recorded prospectively. Symptoms during stress were recorded and defined as mild, moderate or severe. An adverse event was defined as any symptom that persisted for more than 30 min or that required investigation or treatment. Of 1,764 consecutive patients, 1,581 (90%) received regadenoson combined with submaximal exercise unless contraindicated. Symptoms were common (63%) but transient and well-tolerated. The severity of symptoms was recorded in most patients as mild (84%). Dyspnoea (36%) and chest discomfort (12%) were the commonest side effects. Adverse events were reported in eight patients (0.5%), thought to be vasovagal in seven of these. All patients recovered fully without sequelae. There were no deaths, myocardial infarction or hospital admissions. Regadenoson stress was performed in 206 patients (12%) with asthma or chronic obstructive pulmonary disease (COPD) without bronchospasm or any other major side effect. We studied the symptom profile of regadenoson in the largest European cohort to date. Regadenoson combined with submaximal exercise was well tolerated, notably also in patients with asthma or COPD. The majority of regadenoson-related adverse events were vasovagal episodes without sequelae.

  10. Monitoring Training Progress During Exercise Training in Cancer Survivors : A Submaximal Exercise Test as an Alternative for a Maximal Exercise Test?

    NARCIS (Netherlands)

    May, Anne M.; van Weert, Ellen; Korstjens, Irene; Hoekstra-Weebers, Josette E.; van der Schans, Cees P.; Zonderland, Maria L.; Mesters, Ilse; van den Borne, Bart; Ros, Wynand J.

    May AM, van Weert E, Korstjens 1, Hoekstra-Weebers JE, van der Schans CP, Zonderland ML, Mesters 1, van den Borne B, Ros WJ. Monitoring training progress during exercise training in cancer survivors: a submaximal exercise test as an alternative for a maximal exercise test? Arch Phys Med Rehabil

  11. Dichloroacetate therapy attenuates the blood lactate response to submaximal exercise in patients with defects in mitochondrial energy metabolism.

    Science.gov (United States)

    Duncan, G E; Perkins, L A; Theriaque, D W; Neiberger, R E; Stacpoole, P W

    2004-04-01

    We determined acute and chronic effects of dichloroacetate (DCA) on maximal (MAX) and submaximal (SUB) exercise responses in patients with abnormal mitochondrial energetics. Subjects (n = 9) completed a MAX treadmill bout 1 h after ingesting 25 mg/kg DCA or placebo (PL). A 15-min SUB bout was completed the next day while receiving the same treatment. After a 1-d washout, MAX and SUB were repeated while receiving the alternate treatment (acute). Gas exchange and heart rate were measured throughout all tests. Blood lactate (Bla) was measured 0, 3, and 10 min after MAX, and 5, 10, and 15 min during SUB. MAX and SUB were repeated after 3 months of daily DCA or PL. After a 2-wk washout, a final MAX and SUB were completed after 3 months of alternate treatment (chronic). Average Bla during SUB was lower (P abnormal mitochondrial energetics.

  12. Effect of chain wheel shape on crank torque, freely chosen pedal rate, and physiological responses during submaximal cycling

    DEFF Research Database (Denmark)

    Hansen, Ernst Albin; Jensen, Kurt; Hallén, Jostein

    2009-01-01

    . A musculoskeletal simulation model supported the idea that a contributing factor to the observed difference in blood lactate concentration may be slightly reduced muscle activity around the phase where peak crank torque occurs during cycling with the Biopace chain wheel. In that particular phase of the crank......The development of noncircular chain wheels for the enhancement of cycling performance has been in progress for a long time and continues apace. In this study we tested whether submaximal cycling using a non-circular (Biopace) versus a circular chain wheel resulted in lower peak crank torque...... chain wheel at 180 W at 65 and 90 rpm for recording of crank torque profiles, and at their freely chosen pedal rate for recording of pedal rate and metabolic response, including oxygen uptake and blood lactate concentration. Crank torque profiles were similar between the two chain wheels during cycling...

  13. Torque decrease during submaximal evoked contractions of the quadriceps muscle is linked not only to muscle fatigue.

    Science.gov (United States)

    Matkowski, Boris; Lepers, Romuald; Martin, Alain

    2015-05-01

    The aim of this study was to analyze the neuromuscular mechanisms involved in the torque decrease induced by submaximal electromyostimulation (EMS) of the quadriceps muscle. It was hypothesized that torque decrease after EMS would reflect the fatigability of the activated motor units (MUs), but also a reduction in the number of MUs recruited as a result of changes in axonal excitability threshold. Two experiments were performed on 20 men to analyze 1) the supramaximal twitch superimposed and evoked at rest during EMS (Experiment 1, n = 9) and 2) the twitch response and torque-frequency relation of the MUs activated by EMS (Experiment 2, n = 11). Torque loss was assessed by 15 EMS-evoked contractions (50 Hz; 6 s on/6 s off), elicited at a constant intensity that evoked 20% of the maximal voluntary contraction (MVC) torque. The same stimulation intensity delivered over the muscles was used to induce the torque-frequency relation and the single electrical pulse evoked after each EMS contraction (Experiment 2). In Experiment 1, supramaximal twitch was induced by femoral nerve stimulation. Torque decreased by ~60% during EMS-evoked contractions and by only ~18% during MVCs. This was accompanied by a rightward shift of the torque-frequency relation of MUs activated and an increase of the ratio between the superimposed and posttetanic maximal twitch evoked during EMS contraction. These findings suggest that the torque decrease observed during submaximal EMS-evoked contractions involved muscular mechanisms but also a reduction in the number of MUs recruited due to changes in axonal excitability. Copyright © 2015 the American Physiological Society.

  14. Efeitos cardiovasculares da abstinência do fumo no repouso e durante o exercício submáximo em mulheres jovens fumantes Cardiovascular effects of smoking abstinence at rest and during submaximal exercise in young female smokers

    Directory of Open Access Journals (Sweden)

    Demilto Yamaguchi da Pureza

    2007-10-01

    (76 ± 1 mmHg and 86 ± 5 bpm when compared to the NSW group (68 ± 2 mmHg and 72 ± 2 bpm. After 24 hours of no tobacco use, the groups presented similar values. During exercise, SBP and HR increased in the studied groups. DBP was higher in the SW group (~15% in relation to the NSW group in all periods of exercise training. In the abstinence period, DBP only increased in the last load of exercise. During recovery period, in basal condition and 24h-abstinence, both DBP and HR were higher in the SW group when compared to the NSW group. CONCLUSION: These results show that young female smokers present harmful consequences in hemodynamic parameters at rest and in response to submaximal exercise. These findings can be partly reverted by short-term abstinence from tobacco use.

  15. Cardiac autonomic dysfunction in chronic stroke women is attenuated after submaximal exercise test, as evaluated by linear and nonlinear analysis.

    Science.gov (United States)

    Francica, Juliana Valente; Bigongiari, Aline; Mochizuki, Luís; Scapini, Kátia Bilhar; Moraes, Oscar Albuquerque; Mostarda, Cristiano; Caperuto, Erico Chagas; Irigoyen, Maria Cláudia; De Angelis, Katia; Rodrigues, Bruno

    2015-09-29

    We evaluated cardiac autonomic modulation in women with chronic ischemic stroke (at least 4 years post-stroke) at rest and in response to submaximal exercise test. Fourteen post-stroke women (S group) and 10 healthy women (C group) participated in this study. Autonomic modulation (using linear and nonlinear analysis), blood pressure and metabolic variables at rest were evaluated immediately after the exercise test and during the recovery period (20 min). All participants underwent submaximal exercise test on cycle ergometer with gas analysis. At rest, the S group displayed higher lactate concentration, systolic (SBP) and diastolic blood pressure (DBP) values when compared to C group. Furthermore, the S group had lower heart rate variability (HRV) in time domain (SDNN: S = 30 ± 5 vs. 40 ± 8 ms; rMSSD: S = 14 ± 2 vs. C = 34 ± 3 ms), decreased high frequency band of pulse interval (S = 8.4 ± 2 vs. 33.1 ± 9 %) and 2V pattern of symbolic analysis (S = 17.3 ± 1 vs. 30 ± 3 %) (both indicators of cardiac vagal modulation) when compared to C group. Immediately after exercise, S group presented higher values of lactate, SBP, DBP and double product when compared to C group, as well as decreased heart rate recovery (HRR) measured at the first, second and third minutes. At recovery time, all HRV parameters in time and frequency domains improved in the S group; however, HF band remained lower when compared to C group. After the exercise test, women with chronic stroke presented reduced heart rate variability, reduced cardiac vagal modulation, as well as reduced HRR, while displayed an improvement of heart rate variability and cardiac vagal modulation when compared to their baseline. These results reinforce the importance of a physically active lifestyle for cardiovascular autonomic disorders observed in chronic stroke women.

  16. Heavy strength training improves running and cycling performance following prolonged submaximal work in well-trained female athletes.

    Science.gov (United States)

    Vikmoen, Olav; Rønnestad, Bent R; Ellefsen, Stian; Raastad, Truls

    2017-03-01

    The purpose of this study was to investigate the effects of adding heavy strength training to female duathletes' normal endurance training on both cycling and running performance. Nineteen well-trained female duathletes ( V O 2max cycling: 54 ± 3 ml∙kg -1 ∙min -1 , VO 2max running: 53 ± 3 ml∙kg -1 ∙min -1 ) were randomly assigned to either normal endurance training ( E , n  = 8) or normal endurance training combined with strength training ( E+S , n  = 11). The strength training consisted of four lower body exercises [3 × 4-10 repetition maximum (RM)] twice a week for 11 weeks. Running and cycling performance were assessed using 5-min all-out tests, performed immediately after prolonged periods of submaximal work (3 h cycling or 1.5 h running). E+S increased 1RM in half squat (45 ± 22%) and lean mass in the legs (3.1 ± 4.0%) more than E Performance during the 5-min all-out test increased in both cycling (7.0 ± 4.5%) and running (4.7 ± 6.0%) in E+S, whereas no changes occurred in E The changes in running performance were different between groups. E+S reduced oxygen consumption and heart rate during the final 2 h of prolonged cycling, whereas no changes occurred in E No changes occurred during the prolonged running in any group. Adding strength training to normal endurance training in well-trained female duathletes improved both running and cycling performance when tested immediately after prolonged submaximal work. © 2017 The Authors. Physiological Reports published by Wiley Periodicals, Inc. on behalf of The Physiological Society and the American Physiological Society.

  17. Developing new VO2max prediction models from maximal, submaximal and questionnaire variables using support vector machines combined with feature selection.

    Science.gov (United States)

    Abut, Fatih; Akay, Mehmet Fatih; George, James

    2016-12-01

    Maximal oxygen uptake (VO2max) is an essential part of health and physical fitness, and refers to the highest rate of oxygen consumption an individual can attain during exhaustive exercise. In this study, for the first time in the literature, we combine the triple of maximal, submaximal and questionnaire variables to propose new VO2max prediction models using Support Vector Machines (SVM's) combined with the Relief-F feature selector to predict and reveal the distinct predictors of VO2max. For comparison purposes, hybrid models based on double combinations of maximal, submaximal and questionnaire variables have also been developed. By utilizing 10-fold cross-validation, the performance of the models has been calculated using multiple correlation coefficient (R) and root mean square error (RMSE). The results show that the best values of R and RMSE, with 0.94 and 2.92mLkg-1min-1 respectively, have been obtained by combining the triple of relevantly identified maximal, submaximal and questionnaire variables. Compared with the results of the rest of hybrid models in this study and the other prediction models in literature, the reported values of R and RMSE have been found to be considerably more accurate. The predictor variables gender, age, maximal heart rate (MX-HR), submaximal ending speed (SM-ES) of the treadmill and Perceived Functional Ability (Q-PFA) questionnaire have been found to be the most relevant variables in predicting VO2max. The results have also been compared with that of Multilayer Perceptron (MLP) and Tree Boost (TB), and it is seen that SVM significantly outperforms other regression methods for prediction of VO2max. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Evaluation of Maximal Oxygen Uptake and Submaximal Estimates of VO2max Before, During, and After Long Duration International Space Station Missions

    Science.gov (United States)

    2008-01-01

    Evaluation of Maximal Oxygen Uptake and Submaximal Estimates of VO2max Before, During, and After Long Duration International Space Station Missions (VO2max) will document changes in maximum oxygen uptake for crewmembers onboard the International Space Station (ISS) on long-duration missions, greater than 90 days. This investigation will establish the characteristics of VO2max during flight and assess the validity of the current methods of tracking aerobic capacity change during and following the ISS missions.

  19. Amputee Locomotion: Ground Reaction Forces During Submaximal Running With Running-Specific Prostheses.

    Science.gov (United States)

    Baum, Brian S; Hobara, Hiroaki; Kim, Yoon Hyuk; Shim, Jae Kun

    2016-06-01

    Individuals with lower extremity amputation must adapt the mechanical interactions between the feet and ground to account for musculoskeletal function loss. However, it is currently unknown how individuals with amputation modulate three-dimensional ground reaction forces (GRFs) when running. This study aimed to understand how running with running-specific prostheses influences three-dimensional support forces from the ground. Eight individuals with unilateral transtibial amputations and 8 control subjects ran overground at 2.5, 3.0, and 3.5 m/s. Ten force plates measured GRFs at 1000 Hz. Peak and average GRFs and impulses in each plane were compared between limbs and groups. Prosthetic limbs generated reduced vertical impulses, braking forces and impulses, and mediolateral forces while generating similar propulsive impulses compared with intact and control limbs. Intact limbs generated greater peak and average vertical forces and average braking forces than control subjects' limbs. These data indicate that the nonamputated limb experiences elevated mechanical loading compared with prosthetic and control limbs. This may place individuals with amputation at greater risk of acute injury or joint degeneration in their intact limb. Individuals with amputation adapted to running-specific prosthesis force production limitations by generating longer periods of positive impulse thus producing propulsive impulses equivalent to intact and control limbs.

  20. Effects of Submaximal Aerobic Exercise on Regulatory T Cell Markers of Male Patients Suffering from Ischemic Heart Disease.

    Science.gov (United States)

    Raygan, Fariba; Sayyah, Mansour; Janesar Qamsari, Seyed Mohammad Reza; Nikoueinejad, Hassan; Sehat, Mojtaba

    2017-02-01

    There are confirmed beneficiary effects of exercise on atherosclerotic inflammation of ischemia-associated heart diseases. The purpose of this study was to evaluate the effect of aerobic exercise on T-regulatory cell markers of IL-35 as well as FoxP3 and T-helper2 marker of IL-33 in patients with ischemic heart disease (IHD). This research was performed on 44 asymptomatic male patients with ischemic heart disease. The participants were randomly assigned into two groups of submaximal aerobic exercise and control group. Blood samples were collected before and after the termination of the exercise protocol. Serum levels of IL-35 and IL-33 as well as the amount of FoxP3 gene expression in peripheral blood mononuclear cells were measured by Elisa and Real time PCR, respectively. Serum levels of IL-35 (p=0.001) as well as the amount of FoxP3 gene expression increased significantly (p=0.012)  in exercise group even after controlling the likely confounding effects of age, length of ischemia, duration of the disease, and the amount of such factors before exercise (p≤0.042). It seems that exercise may yield a better control of atherosclerotic inflammation in patients with ischemic heart disease through the induction of regulatory T cells.

  1. Identification of patients at low risk of dying after acute myocardial infarction, by simple clinical and submaximal exercise test criteria.

    Science.gov (United States)

    Campbell, S; A'Hern, R; Quigley, P; Vincent, R; Jewitt, D; Chamberlain, D

    1988-09-01

    A consecutive series of 559 hospital survivors of acute myocardial infarction aged less than 66 years were studied; 93 were designated prospectively as low-risk because they were suitable for early submaximal exercise testing and had none of the following clinical or exercise test 'risk factors': (1) angina for at least one month prior to infarction; (2) symptomatic ventricular arrhythmias, or (3) recurrent ischaemic pain, both after the first 24 h of infarction; (4) cardiac failure; (5) cardiomegaly; and (6) an abnormal exercise test (angina, ST-depression or poor blood pressure response). Altogether 301 patients were exercised; their mortality over a median follow-up of 2.4 years was 10.2%, versus 24.6% in the 258 patients not exercised (P = 0.0005). Absence of clinical 'risk factors' alone, in the exercised patients, identified 156 with a mortality of 5.4% versus 15.6% in the 145 with at least one clinical 'risk factor' (P = 0.004). The fully defined low-risk group comprised 93 of the former patients who had neither clinical nor exercise test 'risk factors'. None of these patients died compared with 19 of those with at least one 'risk factor' (mortality = 14.7%; P = 0.002). Their respective rates of non-fatal reinfarction were similar and never exceeded 5% per annum. Therefore, simple clinical and exercise test criteria can positively identify low-risk patients after infarction in whom secondary prevention may be inappropriate.

  2. Interaction effects of time of day and sub-maximal treadmill exercise on the main determinants of blood fluidity.

    Science.gov (United States)

    Ahmadizad, Sajad; Bassami, Minoo

    2010-01-01

    The purpose of this study was to investigate the effects of time of day on responses of the main determinants of blood rheology to acute endurance exercise. Ten healthy male subjects (age, 26.9 +/- 5.5 yr) performed two bouts of running at 65% of VO2peak for 45 min on a motorised treadmill in the morning (08:00 h) and evening (20:00 h), which were followed by 30 min recovery. The two exercise trials were performed in two separate days with 7 days intervening. Haemorheological variables were measured before, immediately after exercise and after recovery. Haematocrit, haemoglobin and RBC count were increased significantly (p evening trials and normalised following recovery, irrespective of time of day. Plasma viscosity increased significantly (F2,18 = 12.4, p exercise in both trials and returned to pre-exercise level at the end of recovery. Baseline values (p exercise were significantly affected by time of day. Neither a significant main effect of exercise nor a significant (p > 0.05) time-of-day effect was found for plasma proteins. It was concluded that sub-maximal running at 08:00 or 20:00 h does not induce different responses in the main determinant of blood rheology.

  3. Endurance and fatigue characteristics in the neck muscles during sub-maximal isometric test in patients with cervical radiculopathy.

    Science.gov (United States)

    Halvorsen, Marie; Abbott, Allan; Peolsson, Anneli; Dedering, Åsa

    2014-03-01

    The aim of the study was to compare myoelectric manifestation in neck muscle endurance and fatigue characteristics during sub-maximal isometric endurance test in patients with cervical radiculopathy and asymptomatic subjects. An additional aim was to explore associations between primary neck muscle endurance, myoelectric fatigability, and self-rated levels of fatigue, pain and subjective health measurements in patients with cervical radiculopathy. Muscle fatigue in the ventral and dorsal neck muscles was assessed in patients with cervical radiculopathy and in an asymptomatic group during an isometric neck muscle endurance test in prone and supine. 46 patients and 34 asymptomatic subjects participated. Surface electromyography signals were recorded from the sternocleidomastoid, cervical paraspinal muscles and upper and middle trapezius bilaterally during the endurance test. Subjective health measurements were assessed with questionnaires. The results showed altered neck muscle endurance in several of the muscles investigated with greater negative median frequency slope, greater variability, side imbalance, lower endurance time and higher experience of fatigue among the cervical radiculopathy patients compared with healthy subjects. Endurance times were significantly lower in both prone and in supine positions between the patients compared to asymptomatic subjects. During the neck muscle endurance test, fatigues in the upper trapezius muscles during the prone test and in the sternocleidomastoid muscles during the supine test were of more importance than self-perceived pain, fatigue, disability and kinesiophobia in predicting neck muscle endurance (NME). NME testing in the primary neck muscles seems to be an important factor to take into consideration in rehabilitation.

  4. Estimating Neural Control from Concentric vs. Eccentric Surface Electromyographic Representations during Fatiguing, Cyclic Submaximal Back Extension Exercises

    Directory of Open Access Journals (Sweden)

    Gerold R. Ebenbichler

    2017-05-01

    Full Text Available Purpose: To investigate the differences in neural control of back muscles activated during the eccentric vs. the concentric portions of a cyclic, submaximal, fatiguing trunk extension exercise via the analysis of amplitude and time-frequency parameters derived from surface electromyographic (SEMG data.Methods: Using back dynamometers, 87 healthy volunteers performed three maximum voluntary isometric trunk extensions (MVC's, an isometric trunk extension at 80% MVC, and 25 cyclic, dynamic trunk extensions at 50% MVC. Dynamic testing was performed with the trunk angular displacement ranging from 0° to 40° and the trunk angular velocity set at 20°/s. SEMG data was recorded bilaterally from the iliocostalis lumborum at L1, the longissimus dorsi at L2, and the multifidus muscles at L5. The initial value and slope of the root mean square (RMS-SEMG and the instantaneous median frequency (IMDF-SEMG estimates derived from the SEMG recorded during each exercise cycle were used to investigate the differences in MU control marking the eccentric vs. the concentric portions of the exercise.Results: During the concentric portions of the exercise, the initial RMS-SEMG values were almost twice those observed during the eccentric portions of the exercise. The RMS-SEMG values generally increased during the concentric portions of the exercise while they mostly remained unchanged during the eccentric portions of the exercise with significant differences between contraction types. Neither the initial IMDF-SEMG values nor the time-course of the IMDF-SEMG values significantly differed between the eccentric and the concentric portions of the exercise.Conclusions: The comparison of the investigated SEMG parameters revealed distinct neural control strategies during the eccentric vs. the concentric portions of the cyclic exercise. We explain these differences by relying upon the principles of orderly recruitment and common drive governing motor unit behavior.

  5. High-frequency submaximal stimulation over muscle evokes centrally generated forces in human upper limb skeletal muscles.

    Science.gov (United States)

    Blouin, Jean-Sébastien; Walsh, Lee D; Nickolls, Peter; Gandevia, Simon C

    2009-02-01

    Control of posture and movement requires control of the output from motoneurons. Motoneurons of human lower limb muscles exhibit sustained, submaximal activity to high-frequency electrical trains, which has been hypothesized to be partly triggered by monosynaptic Ia afferents. The possibility to trigger such behavior in upper limb motoneurons and the potential unique role of Ia afferents to trigger such behavior remain unclear. Subjects (n = 9) received high-frequency trains of electrical stimuli over biceps brachii and flexor pollicis longus (FPL). We chose to study the FPL muscle because it has weak monosynaptic Ia afferent connectivity and it is involved in fine motor control of the thumb. Two types of stimulus trains (100-Hz bursts and triangular ramps) were tested at five intensities below painful levels. All subjects exhibited enhanced torque in biceps and FPL muscles after both types of high-frequency train. Torques also persisted after stimulation, particularly for the highest stimulus intensity. To separate the evoked torques that resulted from a peripheral mechanism (e.g., muscle potentiation) and that which resulted from a central origin, we studied FPL responses to high-frequency trains after complete combined nerve blocks of the median and radial nerves (n = 2). During the blocks, high-frequency trains over the FPL did not yield torque enhancements or persisting torques. These results suggest that enhanced contractions of central origin can be elicited in motoneurons innervating the upper limb, despite weak monosynaptic Ia connections for FPL. Their presence in a recently evolved human muscle (FPL) indicates that these enhanced contractions may have a broad role in controlling tonic postural outputs of hand muscles and that they may be available even for fine motor activities involving the thumb.

  6. Effect of strength training with blood flow restriction on muscle power and submaximal strength in eumenorrheic women.

    Science.gov (United States)

    Gil, Ana L S; Neto, Gabriel R; Sousa, Maria S C; Dias, Ingrid; Vianna, Jeferson; Nunes, Rodolfo A M; Novaes, Jefferson S

    2017-03-01

    Blood flow restriction (BFR) training stimulates muscle size and strength by increasing muscle activation, accumulation of metabolites and muscle swelling. This method has been used in different populations, but no studies have evaluated the effects of training on muscle power and submaximal strength (SS) in accounted for the menstrual cycle. The aim of this study was to analyse the effect of strength training (ST) with BFR on the muscle power and SS of upper and lower limbs in eumenorrheic women. Forty untrained women (18-40 years) were divided randomly and proportionally into four groups: (i) high-intensity ST at 80% of 1RM (HI), (ii) low-intensity ST at 20% of 1RM combined with partial blood flow restriction (LI + BFR), (iii) low-intensity ST at 20% of 1RM (LI) and d) control group (CG). Each training group performed eight training sessions. Tests with a medicine ball (MB), horizontal jump (HJ), vertical jump (VJ), biceps curls (BC) and knee extension (KE) were performed during the 1st day follicular phase (FP), 14th day (ovulatory phase) and 26-28th days (luteal phase) of the menstrual cycle. There was no significant difference among groups in terms of the MB, HJ, VJ or BC results at any time point (P>0·05). SS in the KE exercise was significantly greater in the LI + BFR group compared to the CG group (P = 0·014) during the LP. Therefore, ST with BFR does not appear to improve the power of upper and lower limbs and may be an alternative to improve the SS of lower limbs of eumenorrheic women. © 2015 Scandinavian Society of Clinical Physiology and Nuclear Medicine. Published by John Wiley & Sons Ltd.

  7. Met-enkephalin, beta-endorphin and cortisol responses to sub-maximal exercise after sleep disturbances.

    Science.gov (United States)

    Mougin, F; Simon-Rigaud, M L; Mougin, C; Bourdin, H; Jacquier, M C; Henriet, M T; Davenne, D; Kantelip, J P; Magnin, P; Gaillard, R C

    1992-01-01

    The present study compared the effects of partial sleep deprivation and the effects of an intake of a hypnotic compound (zolpidem) prior to bedtime, on sleep and on hormonal and metabolic adaptations to subsequent exercise. Sleep deprivation consisted of a delayed bedtime and an early getting-up time. Eight young subjects, who slept well and were highly trained athletes, were enrolled in this study. Sleep was recorded polygraphically and the following afternoon exercise was performed on a cycle ergometer for 30 min at 75% of maximal oxygen consumption (VO2max) after a 10-min warm up. Met-enkephalin, beta-endorphin, cortisol, and lactate concentrations were measured at rest and during exercise. The data obtained after experimental sleep, with and without medication were compared with those obtained in the reference condition with normal sleep. Both types of sleep reduction decreased the total sleep time, stage 2 sleep, and rapid eye movement sleep, whereas zolpidem administration did not modify either the duration of sleep or the sleep stages. After the reference night, plasma met-enkephalin did not show any significant change at the end of the submaximal exercise, whereas beta-endorphin, cortisol, and lactic acid concentrations increased significantly in all subjects. The changes in concentration in beta-endorphin were significantly related to the changes in cortisol (r = 0.78; P less than 0.01) and to the changes in plasma lactic acid (r = 0.58; P less than 0.05). Cortisol concentrations were also related to lactic acid values (r = 0.94; P less than 0.01).(ABSTRACT TRUNCATED AT 250 WORDS)

  8. Muscle coordination, activation and kinematics of world-class and elite breaststroke swimmers during submaximal and maximal efforts.

    Science.gov (United States)

    Olstad, Bjørn Harald; Vaz, João Rocha; Zinner, Christoph; Cabri, Jan M H; Kjendlie, Per-Ludvik

    2017-06-01

    The aims of this study were to describe muscular activation patterns and kinematic variables during the complete stroke cycle (SC) and the different phases of breaststroke swimming at submaximal and maximal efforts. Surface electromyography (sEMG) was collected from eight muscles in nine elite swimmers; five females (age 20.3 ± 5.4 years; Fédération Internationale de Natation [FINA] points 815 ± 160) and four males (27.7 ± 7.1 years; FINA points 879 ± 151). Underwater cameras were used for 3D kinematic analysis with automatic motion tracking. The participants swam 25 m of breaststroke at 60%, 80% and 100% effort and each SC was divided into three phases: knee extension, knee extended and knee flexion. With increasing effort, the swimmers decreased their SC distance and increased their velocity and stroke rate. A decrease during the different phases was found for duration during knee extended and knee flexion, distance during knee extended and knee angle at the beginning of knee extension with increasing effort. Velocity increased for all phases. The mean activation pattern remained similar across the different effort levels, but the muscles showed longer activation periods relative to the SC and increased integrated sEMG (except trapezius) with increasing effort. The muscle activation patterns, muscular participation and kinematics assessed in this study with elite breaststroke swimmers contribute to a better understanding of the stroke and what occurs at different effort levels. This could be used as a reference for optimising breaststroke training to improve performance.

  9. Influence of Dietary Acid Load on Exercise Performance.

    Science.gov (United States)

    Applegate, Catherine; Mueller, Mackenzie; Zuniga, Krystle E

    2017-06-01

    Diet composition can affect systemic pH and acid-base regulation, which may in turn influence exercise performance. An acidic environment in the muscle impairs performance and contributes to fatigue; therefore, current trends in sports nutrition place importance on maximizing the alkalinity of the body with ergogenic aids and dietary strategies. This review examines the evidence on the effects of dietary manipulations on acid load and exercise performance. Ten studies that investigated the effect of high versus low dietary acid loads on athletic performance generally identified that low dietary acid loads increased plasma pH, but did not consistently improve exercise performance at maximal or submaximal exercise intensities. In addition, the few studies conducted have several limitations including lack of female subjects and use of exercise tests exclusive to cycling or treadmill running. Although the research does not strongly support a performance benefit from low dietary acid loads, a more alkaline dietary pattern may be beneficial for overall health, as dietary induced acidosis has been associated with greater risk of cardiovascular disease and bone disease. The review includes dietary recommendations for athletes to reduce dietary acid load while still meeting sports nutrition recommendations.

  10. Carbohydrate Loading.

    Science.gov (United States)

    Csernus, Marilyn

    Carbohydrate loading is a frequently used technique to improve performance by altering an athlete's diet. The objective is to increase glycogen stored in muscles for use in prolonged strenuous exercise. For two to three days, the athlete consumes a diet that is low in carbohydrates and high in fat and protein while continuing to exercise and…

  11. Influence of obstructive sleep apnea syndrome in the fluctuation of the submaximal isometric torque of knee extensors in patients with early-grade osteoarthritis

    Science.gov (United States)

    Silva, Andressa; Mello, Marco T.; Serrão, Paula R.; Luz, Roberta P.; Bittencourt, Lia R.; Mattiello, Stela M.

    2015-01-01

    OBJECTIVE: The aim of this study was to investigate whether obstructive sleep apnea (OSA) alters the fluctuation of submaximal isometric torque of the knee extensors in patients with early-grade osteoarthritis (OA). METHOD: The study included 60 male volunteers, aged 40 to 70 years, divided into four groups: Group 1 (G1) - Control (n=15): without OA and without OSA; Group 2 (G2) (n=15): with OA and without OSA; Group 3 (G3) (n=15): without OA and with OSA; and Group 4 (G4) (n=15) with OA and with OSA. Five patients underwent maximal isometric contractions of 10 seconds duration each, with the knee at 60° of flexion to determine peak torque at 60°. To evaluate the fluctuation of torque, 5 submaximal isometric contractions (50% of maximum peak torque) of 10 seconds each, which were calculated from the standard deviation of torque and coefficient of variation, were performed. RESULTS: Significant differences were observed between groups for maximum peak torque, while G4 showed a lower value compared with G1 (p=0.005). Additionally, for the average torque exerted, G4 showed a lower value compared to the G1 (p=0.036). However, no differences were found between the groups for the standard deviation (p=0.844) and the coefficient of variation (p=0.143). CONCLUSION: The authors concluded that OSA did not change the parameters of the fluctuation of isometric submaximal torque of knee extensors in patients with early-grade OA. PMID:26443974

  12. Human skeletal muscle type 1 fibre distribution and response of stress-sensing proteins along the titin molecule after submaximal exhaustive exercise.

    Science.gov (United States)

    Koskinen, Satu O A; Kyröläinen, Heikki; Flink, Riina; Selänne, Harri P; Gagnon, Sheila S; Ahtiainen, Juha P; Nindl, Bradley C; Lehti, Maarit

    2017-11-01

    Early responses of stress-sensing proteins, muscle LIM protein (MLP), ankyrin repeat proteins (Ankrd1/CARP and Ankrd2/Arpp) and muscle-specific RING finger proteins (MuRF1 and MuRF2), along the titin molecule were investigated in the present experiment after submaximal exhaustive exercise. Ten healthy men performed continuous drop jumping unilaterally on a sledge apparatus with a submaximal height until complete exhaustion. Five stress-sensing proteins were analysed by mRNA measurements from biopsies obtained immediately and 3 h after the exercise from exercised vastus lateralis muscle while control biopsies were obtained from non-exercised legs before the exercise. Decreased maximal jump height and increased serum creatine kinase activities as indirect markers for muscle damage and HSP27 immunostainings on muscle biopsies as a direct marker for muscle damage indicated that the current exercised protocol caused muscle damage. mRNA levels for four (MLP, Ankrd1/CARP, MuRF1 and MuRF2) out of the five studied stress sensors significantly (p exercise. The magnitude of MLP and Ankrd2 responses was related to the proportion of type 1 myofibres. Our data showed that the submaximal exhaustive exercise with subject's own physical fitness level activates titin-based stretch-sensing proteins. These results suggest that both degenerative and regenerative pathways are activated in very early phase after the exercise or probably already during the exercise. Activation of these proteins represents an initial step forward adaptive remodelling of the exercised muscle and may also be involved in the initiation of myofibre repair.

  13. Evaluation of respiratory dynamics by volumetric capnography during submaximal exercise protocol of six minutes on treadmill in cystic fibrosis patients.

    Science.gov (United States)

    Parazzi, Paloma L F; Marson, Fernando A L; Ribeiro, Maria A G O; Schivinski, Camila I S; Ribeiro, José D

    2017-11-29

    Volumetric capnography provides the standard CO2 elimination by the volume expired per respiratory cycle and is a measure to assess pulmonary involvement. Thus, the objective of this study was to evaluate the respiratory dynamics of healthy control subjects and those with cystic fibrosis in a submaximal exercise protocol for six minutes on the treadmill, using volumetric capnography parameters (slope 3 [Slp3], Slp3/tidal volume [Slp3/TV], and slope 2 [Slp2]). This was a cross-sectional study with 128 subjects (cystic fibrosis, 64 subjects; controls, 64 subjects]. Participants underwent volumetric capnography before, during, and after six minutes on the treadmill. Statistical analysis was performed using the Friedman, Mann-Whitney, and Kruskal-Wallis tests, considering age and sex. An alpha=0.05 was considered. Six minutes on the treadmill evaluation: in cystic fibrosis, volumetric capnography parameters were different before, during, and after six minutes on the treadmill; the same was observed for the controls, except for Slp2. Regarding age, an Slp3 difference was observed in cystic fibrosis patients regardless of age, at all moments, and in controls for age≥12 years; a difference in Slp3/TV was observed in cystic fibrosis and controls, regardless of age; and an Slp2 difference in the cystic fibrosis, regardless of age. Regarding sex, Slp3 and Slp3/TV differences were observed in cystic fibrosis regardless of sex, and in controls in male participants; an Slp2 difference was observed in the cystic fibrosis and female participants. The analysis between groups (cystic fibrosis and controls) indicated that Slp3 and Slp3/TV has identified the CF, regardless of age and sex, while the Slp2 showed the CF considering age. Cystic fibrosis showed greater values of the parameters before, during, and after exercise, even when stratified by age and sex, which may indicate ventilation inhomogeneity in the peripheral pathways in the cystic fibrosis. Copyright © 2017 Sociedade

  14. Effect of Bench Press Load Knowledge on Repetitions, Rating of Perceived Exertion, and Attentional Focus.

    Science.gov (United States)

    Beaudoin, Christina M; Cox, Zachary; Dundore, Tyler; Thomas, Tayler; Kim, Johnathon; Pillivant, Daniel

    2018-02-01

    Beaudoin, CM, Cox, Z, Dundore, T, Thomas, T, Kim, J, and Pillivant, D. Effect of bench press load knowledge on repetitions, rating of perceived exertion, and attentional focus. J Strength Cond Res 32(2): 514-519, 2018-Few studies have examined the role of the teleoanticipation during resistance training. The purpose of this study was to examine the effect of bench press (BP) load knowledge on repetitions completed, ratings of perceived exertion (RPEs), and attentional focus (% associative). Thirty-six recreationally active resistance-trained men (n = 25) and women (n = 11) participated in this study (age = 20.97 ± 1.87 years; ht = 174.12 ± 9.41 cm; and mass = 80.14 ± 14.03 kg). All subjects completed 3 testing sessions: (a) 1 repetition maximum (1RM) BP determination; (b) submaximal BP repetitions to fatigue known load (KL); and (c) submaximal BP repetitions to fatigue unknown load (UL). Known load and UL sessions were randomized and counterbalanced and both completed at 70% 1RM. An estimated weight ratio was computed using the subject's estimate of the UL weight relative to the KL weight. An independent samples t-test revealed no significant testing order difference for the estimated weight ratio. Two-way repeated-measures analysis of variances revealed no significant differences in the number of repetitions (p = 0.63), RPE (p = 0.18), or attentional focus (% associative) (p = 0.93) between the KL and UL conditions. Pearson correlations found a moderate positive association between KL repetitions completed and % associative focus when the UL was completed before the KL. Load knowledge did not influence the number of repetitions, RPE, or attentional focus while completing the BP. Further research examining the use of pacing strategies, RPE, and attentional focus during KL and UL conditions are warranted.

  15. Oxygen uptake kinetics of constant-load work - Upright vs. supine exercise

    Science.gov (United States)

    Convertino, V. A.; Goldwater, D. J.; Sandler, H.

    1984-01-01

    Supine and upright positions were used in a comparitive study of the effects of constant load exercise on oxygen uptake (VO2), O2 deficit, steady-state VO2 and VO2 following recovery from constant load work. Ten male subjects (36-40 yr.) performed one submaximal exercise test in the supine and one test in the upright position consisting of 5 min rest and 5 min cycle ergometer exercise at 700 kg/min followed by ten minutes of recovery. It is found that the significant difference in VO2 kinetics during exercise in the upright compared to supine position resulted from changes in oxygen transport and utilization mechanisms rather than changes in mechanical efficiency. To the extent that data measured in the supine position can be used to estimate physiological responses to zero gravity, it is suggested that limitation of systemic O2 consumption may be the result of slow rates of oxygen uptake during transient periods of muscular work. Significant reductions in the rate of steady-state VO2 attainment at submaximal work intensities may produce an onset of muscle fatigue and exhaustion.

  16. Description of a standardized rehabilitation program based on sub-maximal eccentric following a platelet-rich plasma infiltration for jumper’s knee

    Science.gov (United States)

    Kaux, Jean-François; Forthomme, Bénédicte; Namurois, Marie-Hélène; Bauvir, Philippe; Defawe, Nathalie; Delvaux, François; Lehance, Cédric; Crielaard, Jean-Michel; Croisier, Jean-Louis

    2014-01-01

    Summary Introduction. Different series emphasized the necessity of rehabilitation program after infiltration of platelet-rich plasma (PRP) in case of tendinopathy. However, most of them describe only briefly the reeducation protocol and these programs vary. Our aim was to extensively describe a specific standardized rehabilitation program. Methods. After a review of literature of post-PRP infiltration protocols, we had developed a standardized rehabilitation protocol. This protocol was evaluated by 30 subjects with chronic jumper’s knee who. A standardised progressive sub-maximal eccentric program supervised by a physical therapist for 6 weeks was started 1 week post-infiltration. The patient benefited also from electromyostimulation, isometric strengthening and stretching of the quadriceps, cycloergometer and cryotherapy. After the supervised program, the patient had to make an auto-reeducation added to the reathletisation protocol for 6 more weeks which was followed by maintenance exercises up to 1 year. The assessments were made using a VAS, IKDC and VISA-P scores. Results. The VAS, IKDC and VISA-P scores decreased very significantly with time. The compliance to auto-reeducation was good. Conclusions. We proposed a simple and efficient protocol based on sub-maximal eccentric reeducation to add to PRP infiltrations in case of patellar tendinopathy. PMID:24932453

  17. Effects of a helium/oxygen mixture on individuals' lung function and metabolic cost during submaximal exercise for participants with obstructive lung diseases.

    Science.gov (United States)

    Häussermann, Sabine; Schulze, Anja; Katz, Ira M; Martin, Andrew R; Herpich, Christiane; Hunger, Theresa; Texereau, Joëlle

    2015-01-01

    Helium/oxygen therapies have been studied as a means to reduce the symptoms of obstructive lung diseases with inconclusive results in clinical trials. To better understand this variability in results, an exploratory physiological study was performed comparing the effects of helium/oxygen mixture (78%/22%) to that of medical air. The gas mixtures were administered to healthy, asthmatic, and chronic obstructive pulmonary disease (COPD) participants, both moderate and severe (6 participants in each disease group, a total of 30); at rest and during submaximal cycling exercise with equivalent work rates. Measurements of ventilatory parameters, forced spirometry, and ergospirometry were obtained. There was no statistical difference in ventilatory and cardiac responses to breathing helium/oxygen during submaximal exercise. For asthmatics, but not for the COPD participants, there was a statistically significant benefit in reduced metabolic cost, determined through measurement of oxygen uptake, for the same exercise work rate. However, the individual data show that there were a mixture of responders and nonresponders to helium/oxygen in all of the groups. The inconsistent response to helium/oxygen between individuals is perhaps the key drawback to the more effective and widespread use of helium/oxygen to increase exercise capacity and for other therapeutic applications.

  18. Effects of a helium/oxygen mixture on individuals’ lung function and metabolic cost during submaximal exercise for participants with obstructive lung diseases

    Science.gov (United States)

    Häussermann, Sabine; Schulze, Anja; Katz, Ira M; Martin, Andrew R; Herpich, Christiane; Hunger, Theresa; Texereau, Joëlle

    2015-01-01

    Background Helium/oxygen therapies have been studied as a means to reduce the symptoms of obstructive lung diseases with inconclusive results in clinical trials. To better understand this variability in results, an exploratory physiological study was performed comparing the effects of helium/oxygen mixture (78%/22%) to that of medical air. Methods The gas mixtures were administered to healthy, asthmatic, and chronic obstructive pulmonary disease (COPD) participants, both moderate and severe (6 participants in each disease group, a total of 30); at rest and during submaximal cycling exercise with equivalent work rates. Measurements of ventilatory parameters, forced spirometry, and ergospirometry were obtained. Results There was no statistical difference in ventilatory and cardiac responses to breathing helium/oxygen during submaximal exercise. For asthmatics, but not for the COPD participants, there was a statistically significant benefit in reduced metabolic cost, determined through measurement of oxygen uptake, for the same exercise work rate. However, the individual data show that there were a mixture of responders and nonresponders to helium/oxygen in all of the groups. Conclusion The inconsistent response to helium/oxygen between individuals is perhaps the key drawback to the more effective and widespread use of helium/oxygen to increase exercise capacity and for other therapeutic applications. PMID:26451096

  19. Load testing circuit

    DEFF Research Database (Denmark)

    2009-01-01

    A load testing circuit a circuit tests the load impedance of a load connected to an amplifier. The load impedance includes a first terminal and a second terminal, the load testing circuit comprising a signal generator providing a test signal of a defined bandwidth to the first terminal of the load...

  20. Inspiratory muscle training improves exercise capacity with thoracic load carriage.

    Science.gov (United States)

    Shei, Ren-Jay; Chapman, Robert F; Gruber, Allison H; Mickleborough, Timothy D

    2018-02-01

    Thoracic load carriage (LC) exercise impairs exercise performance compared to unloaded exercise, partially due to impaired respiratory mechanics. We investigated the effects of LC on exercise and diaphragmatic fatigue in a constant-load exercise task; and whether inspiratory muscle training (IMT) improved exercise capacity and diaphragmatic fatigue with LC. Twelve recreationally active males completed three separate running trials to exhaustion (T lim ) at a fixed speed eliciting 70% of their V˙O 2max . The first two trials were completed either unloaded (UL) or while carrying a 10 kg backpack (LC). Subjects then completed 6 weeks of either true IMT or placebo-IMT. Posttraining, subjects completed an additional LC trial identical to the pretraining LC trial. Exercise metabolic and ventilatory measures were recorded. Diaphragm fatigue was assessed as the difference between preexercise and postexercise twitch diaphragmatic pressure (P di, tw ), assessed by bilateral stimulation of the phrenic nerve with esophageal balloon-tipped catheters measuring intrathoracic pressures. T lim was significantly shorter (P  0.05). Minute ventilation and breathing mechanics were unchanged post-IMT (P > 0.05). Six weeks of flow-resistive IMT improved exercise capacity, but did not mitigate diaphragmatic fatigue following submaximal, constant-load running to volitional exhaustion with LC. © 2018 The Authors. Physiological Reports published by Wiley Periodicals, Inc. on behalf of The Physiological Society and the American Physiological Society.

  1. The effect of lifting and lowering an external load on repositioning error of trunk flexion-extension in subjects with and without low back pain.

    Science.gov (United States)

    Lin, Yang Hua; Sun, Ming Hui

    2006-07-01

    To determine whether the repositioning error of trunk flexion-extension in individuals with low back pain is different from that in those not experiencing low back pain when lifting and lowering external loads. A case-control study. Physical therapy department of a medical centre. Twenty subjects with subacute low back pain and 20 control subjects without low back pain. Tasks with and without lifting and lowering an external load. The trunk repositioning errors were measured with Measurand Shape Tape. In subjects with low back pain, trunk repositioning errors were significantly reduced when lifting and lowering an external load in the direction of flexion (3.77 +/- 1.26 degrees in a loaded condition versus 4.82 +/- 2.97 degrees in an unloaded condition; P loaded condition versus 5.03 +/- 3.74 degrees in an unloaded condition; P external load in the direction of flexion (2.80 +/- 1.39 degrees in a loaded condition versus 2.63 +/- 1.24 degrees in an unloaded condition; P > 0.05) and extension (2.87 +/- 11.40 degrees in a loaded condition versus 3.15 +/- 11.50 degrees in an unloaded condition; P > 0.05). The direction of motion (trunk flexion or extension) was not shown to be significant in this study. Performing the task whilst lifting or lowering a submaximal load showed a reduced trunk repositioning error in subjects with subacute low back pain. Lifting and lowering a submaximal load might be considered as one of the rehabilitative strategies to hasten a return to work.

  2. Sub-maximal and maximal Yo-Yo intermittent endurance test level 2: heart rate response, reproducibility and application to elite soccer

    DEFF Research Database (Denmark)

    Bradley, Paul S; Mohr, Magni; Bendiksen, Mads

    2011-01-01

    The aims of this study were to (1) determine the reproducibility of sub-maximal and maximal versions of the Yo-Yo intermittent endurance test level 2 (Yo-Yo IE2 test), (2) assess the relationship between the Yo-Yo IE2 test and match performance and (3) quantify the sensitivity of the Yo-Yo IE2 te......) in Yo-Yo IE2 test performance and heart rate after 6 min were 3.9% (n = 37) and 1.4% (n = 32), respectively. Elite male senior and youth U19 players Yo-Yo IE2 performances were better (P ...

  3. The effect of Sub-maximal exercise-rehabilitation program on cardio-respiratory endurance indexes and oxygen pulse in patients with spastic cerebral palsy

    Directory of Open Access Journals (Sweden)

    M Izadi

    2006-05-01

    Full Text Available Background: Physical or cardio-respiratory fitness are of the best important physiological variables in children with cerebral palsy (CP, but the researches on exercise response of individuals with CP are limited. Our aim was to determine the effect of sub-maximal rehabilitation program (aerobic exercise on maximal oxygen uptake, oxygen pulse and cardio- respiratory physiological variables of children with moderate to severe spastic cerebral palsy diplegia and compare with able-bodied children. Methods: In a controlled clinical trial study, 15 children with diplegia spastic cerebral palsy, were recruited on a voluntarily basis (experimental group and 18 subjects without neurological impairments selected as control group. In CP group, aerobic exercise program performed on the average of exercise intensity (144 beat per minute of heart rate, 3 times a week for 3 months. The time of each exercise session was 20-25 minutes. Dependent variables were measured in before (pretest and after (post test of rehabilitation program through Mac Master Protocol on Tantories cycle ergometer in CP group and compared with the control group. Results: The oxygen pulse (VO2/HR during ergometery protocol was significantly lower in CP group than normal group (P<0.05. No significant statistical difference in maximal oxygen uptake (VO2 max was found between groups. The rehabilitation program leads to little increase of this variable in CP group. After sub-maximal exercise in pretest and post test, the heart rate of patient group was greater than control group, and aerobic exercise leads to significant decrease in heart rate in CP patients(P<0.05. Conclusion: The patients with spastic cerebral palsy, because of high muscle tone, severe spasticity and involuntarily movements have higher energy cost and lower aerobic fitness than normal people. The rehabilitation exercise program can improve physiological function of muscle and cardio-respiratory endurance in these

  4. Coconut Water Does Not Improve Markers of Hydration During Sub-maximal Exercise and Performance in a Subsequent Time Trial Compared with Water Alone.

    Science.gov (United States)

    Peart, Daniel J; Hensby, Andy; Shaw, Matthew P

    2017-06-01

    The purpose of this study was to compare markers of hydration during submaximal exercise and subsequent time trial performance when consuming water (PW) or coconut water (CW). There was also a secondary aim to assess the palatability of CW during exercise and voluntary intake during intense exercise. 10 males (age 27.9 ± 4.9 years, body mass 78.1 ± 10.1kg, average max minute power 300.2 ± 28.2W) completed 60-min of submaximal cycling followed by a 10-km time trial on two occasions. During these trials participants consumed either PW or CW in a randomized manner, drinking a 250 ml of the assigned drink between 10-15 min, 25-30 min and 40-45 min, and then drinking ad libitum from 55-min until the end of the time trial. Body mass and urine osmolality were recorded preexercise and then after 30-min, 60-min, and post time trial. Blood glucose, lactate, heart rate, rate of perceived exertion (RPE; 6-20) and ratings of thirst, sweetness, nausea, fullness and stomach upset (1 =very low/none, 5= very high) were recorded during each drink period. CW did not significantly improve time trial performance compared with PW (971.4 ± 50.5 and 966.6 ± 44.8 s respectively; p = .698) and there was also no significant differences between trials for any of the physiological variables measured. However there were subjective differences between the beverages for taste, resulting in a significantly reduced volume of voluntary intake in the CW trial (115 ± 95.41 ml and 208.7 ± 86.22 ml; p < .001).

  5. Submaximal exercise testing with near-infrared spectroscopy in Myalgic Encephalomyelitis/Chronic Fatigue Syndrome patients compared to healthy controls: a case-control study.

    Science.gov (United States)

    Miller, Ruth R; Reid, W Darlene; Mattman, Andre; Yamabayashi, Cristiane; Steiner, Theodore; Parker, Shoshana; Gardy, Jennifer; Tang, Patrick; Patrick, David M

    2015-05-20

    Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is a debilitating illness. Symptoms include profound fatigue and distinctive post-exertional malaise (PEM). We asked whether a submaximal exercise test would prove useful for identifying different patterns of tissue oxygen utilization in individuals with ME/CFS versus healthy subjects. Such a test has potential to aid with ME/CFS diagnosis, or to characterize patients' illness. A case-control study of 16 patients with ME/CFS compared to 16 healthy controls completing a 3-min handgrip protocol was performed. Response was measured using near-infrared spectroscopy, resulting in measurements of oxygenated (O2Hb) and deoxygenated hemoglobin (HHb) over wrist extensors and flexors. Changes in O2Hb (delta (d)O2Hb) and HHb (dHHb) absorbance between the first and last contraction were calculated, as were the force-time product of all contractions, measured as tension-time index (TTI), and ratings of perceived exertion (RPE). Individuals with ME/CFS demonstrated smaller dO2Hb and dHHb than controls. However, after adjusting for TTI and change in total hemoglobin (delta (d)tHb), differences in dO2Hb and dHHb were reduced, with large overlapping variances. RPE was significantly higher for cases than controls, particularly at rest. Relative to controls, participants with ME/CFS demonstrated higher RPE, lower TTI, and reduced dO2Hb and dHHb during repetitive handgrip exercise, although considerable variance was observed. With further study, submaximal exercise testing may prove useful for stratifying patients with a lower propensity for inducing PEM, and have the ability to establish baseline intensities for exercise prescription.

  6. Effects of a helium/oxygen mixture on individuals’ lung function and metabolic cost during submaximal exercise for participants with obstructive lung diseases

    Directory of Open Access Journals (Sweden)

    Häussermann S

    2015-09-01

    Full Text Available Sabine Häussermann,1 Anja Schulze,1 Ira M Katz,2,3 Andrew R Martin,4 Christiane Herpich,1 Theresa Hunger,1 Joëlle Texereau2 1Inamed GmbH, Gauting, Germany; 2Medical R&D, Air Liquide Santé International, Centre de Recherche Paris-Saclay, Les Loges-en-Josas, France; 3Department of Mechanical Engineering, Lafayette College, Easton, PA, USA; 4Department of Mechanical Engineering, University of Alberta, Edmonton, AB, CanadaBackground: Helium/oxygen therapies have been studied as a means to reduce the symptoms of obstructive lung diseases with inconclusive results in clinical trials. To better understand this variability in results, an exploratory physiological study was performed comparing the effects of helium/oxygen mixture (78%/22% to that of medical air.Methods: The gas mixtures were administered to healthy, asthmatic, and chronic obstructive pulmonary disease (COPD participants, both moderate and severe (6 participants in each disease group, a total of 30; at rest and during submaximal cycling exercise with equivalent work rates. Measurements of ventilatory parameters, forced spirometry, and ergospirometry were obtained.Results: There was no statistical difference in ventilatory and cardiac responses to breathing helium/oxygen during submaximal exercise. For asthmatics, but not for the COPD participants, there was a statistically significant benefit in reduced metabolic cost, determined through measurement of oxygen uptake, for the same exercise work rate. However, the individual data show that there were a mixture of responders and nonresponders to helium/oxygen in all of the groups.Conclusion: The inconsistent response to helium/oxygen between individuals is perhaps the key drawback to the more effective and widespread use of helium/oxygen to increase exercise capacity and for other therapeutic applications. Keywords: helium/oxygen, inspiratory capacity, oxygen uptake, COPD, asthma, obstructive airway diseases, exercise, heliox

  7. Electrical load detection aparatus

    DEFF Research Database (Denmark)

    2010-01-01

    A load detection technique for a load comprising multiple frequency-dependant sub-loads comprises measuring a representation of the impedance characteristic of the load; providing stored representations of a multiplicity of impedance characteristics of the load; each one of the stored representat...

  8. Distribution load estimation (DLE)

    Energy Technology Data Exchange (ETDEWEB)

    Seppaelae, A.; Lehtonen, M. [VTT Energy, Espoo (Finland)

    1998-08-01

    The load research has produced customer class load models to convert the customers` annual energy consumption to hourly load values. The reliability of load models applied from a nation-wide sample is limited in any specific network because many local circumstances are different from utility to utility and time to time. Therefore there is a need to find improvements to the load models or, in general, improvements to the load estimates. In Distribution Load Estimation (DLE) the measurements from the network are utilized to improve the customer class load models. The results of DLE will be new load models that better correspond to the loading of the distribution network but are still close to the original load models obtained by load research. The principal data flow of DLE is presented

  9. Effect of vastus lateralis fatigue on load sharing between quadriceps femoris muscles during isometric knee extensions.

    Science.gov (United States)

    Bouillard, Killian; Jubeau, Marc; Nordez, Antoine; Hug, François

    2014-02-01

    The present study aimed to investigate the effects of selective fatigue (i.e., one muscle of the quadriceps) on load sharing strategies during submaximal knee extensions. Shear wave elastography was used to measure muscle shear elastic modulus, as this is considered to be an index of individual muscle force. Sixteen participants attended two experimental sessions that each involved six 10-s knee extensions at 20% of maximal voluntary contraction (MVC) followed by a sustained submaximal isometric knee extension at 20% of MVC, until task failure (Tlim). Between the 10-s contractions and Tlim, participants were required to rest (5 min) for the control session or underwent 5 min of electromyostimulation (EMS) on vastus lateralis (EMS session). Compared with the control session, vastus lateralis shear elastic modulus values were significantly lower after EMS considering both the start of Tlim (54.6 ± 11.8 vs. 68.4 ± 19.2 kPa; P = 0.011) and the entire Tlim contraction (59.0 ± 14.0 vs. 74.4 ± 20.3 kPa; P = 0.019). However, no significant differences were observed for the other recorded muscles (vastus medialis and rectus femoris; both P = 1), i.e., different patterns of changes were found between participants. In conclusion, this study demonstrates that prefatiguing a single agonist muscle does not lead to a consistent redistribution of load sharing among the quadriceps muscles between individuals. These results suggest that the central nervous system does not use a common principle among individuals to control load sharing when neuromuscular fatigue occurs.

  10. Shooting under cardiovascular load: Electroencephalographic activity in preparation for biathlon shooting.

    Science.gov (United States)

    Gallicchio, Germano; Finkenzeller, Thomas; Sattlecker, Gerold; Lindinger, Stefan; Hoedlmoser, Kerstin

    2016-11-01

    This study explored the influence of sub-maximal cardiovascular load on electroencephalographic (EEG) activity preceding biathlon shooting. Frontal-midline theta and alpha power were examined to assess monitoring processes and cortical inhibition, respectively. Thirteen experienced biathletes (mean age: 17years; 5 males, 8 females) fired sets of five consecutive shots from the standing position at a 50-meter-distant target, under two fixed-order conditions: (i) at rest and (ii) immediately after 3-minute exercise on a bicycle ergometer at 90% of maximum heart rate (HR). HR and rate of physical exertion (RPE) were measured as manipulation checks. Shooting accuracy was assessed in target rings for each shot. Frontal-midline theta and alpha power were computed in the last second preceding each shot from average-reference 61-channel EEG and inter-individual differences were minimized through a median-scaled log transformation (Appendix). HR and RPE increased under cardiovascular load, however, shooting accuracy did not change. Pre-shooting frontal-midline theta power decreased, whereas alpha power increased over temporal and occipital - but not central - regions. These changes were larger for greater HR values. Additionally, higher frontal-midline theta, lower left-central alpha, and higher left-temporal alpha power were associated with more accurate shooting. These findings suggest that monitoring processes are beneficial to shooting performance but can be impaired by sub-maximal cardiovascular load. Greater inhibition of movement-irrelevant regions (temporal, occipital) and concomitant activation of movement-related regions (central) indicate that greater neural efficiency is beneficial to shooting performance and can allow trained biathletes to shoot accurately despite physically demanding conditions. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

  11. Distribution load estimation - DLE

    Energy Technology Data Exchange (ETDEWEB)

    Seppaelae, A. [VTT Energy, Espoo (Finland)

    1996-12-31

    The load research project has produced statistical information in the form of load models to convert the figures of annual energy consumption to hourly load values. The reliability of load models is limited to a certain network because many local circumstances are different from utility to utility and time to time. Therefore there is a need to make improvements in the load models. Distribution load estimation (DLE) is the method developed here to improve load estimates from the load models. The method is also quite cheap to apply as it utilises information that is already available in SCADA systems

  12. Competitive performance, training load and physiological responses during tapering in young swimmers.

    Science.gov (United States)

    Toubekis, Argyris G; Drosou, Evgenia; Gourgoulis, Vassilios; Thomaidis, Savvas; Douda, Helen; Tokmakidis, Savvas P

    2013-01-01

    The study examined the changes of training load and physiological parameters in relation to competitive performance during a period leading to a national championship. The training content of twelve swimmers (age: 14.2±1.3 yrs) was recorded four weeks before the national championship (two weeks of normal training and two weeks of the taper). The training load was calculated: i) by the swimmer's session-RPE score (RPE-Load), ii) by the training intensity levels adjusted after a 7×200-m progressively increasing intensity test (LA-Load). Swimmers completed a 400-m submaximal intensity test, a 15 s tethered swimming and hand-grip strength measurements 34-35 (baseline: Test 1), 20-21 (before taper: Test 2) and 6-7 (Test 3) days before the national championship. Performance during the national championship was not significantly changed compared to season best (0.1±1.6%; 95% confidence limits: -0.9, 1.1%; Effect Size: 0.02, p=0.72) and compared to performance before the start of the two-week taper period (0.9±1.7%; 95% confidence limits: 0.3, 2.1%; Effect size: 0.12, p=0.09). No significant changes were observed in all measured physiological and performance related variables between Test 1, Test 2, and Test 3. Changes in RPE-Load (week-4 vs. week-1) were correlated with changes in performance (r=0.63, p=0.03) and the RPE-Load was correlated with the LA-Load (r=0.80, p=0.01). The estimation of the session-RPE training load may be helpful for taper planning of young swimmers. Increasing the difference between the normal and last week of taper training load may facilitate performance improvements.

  13. Effects of acute caffeinated coffee consumption on energy utilization related to glucose and lipid oxidation from short submaximal treadmill exercise in sedentary men.

    Science.gov (United States)

    Leelarungrayub, Donrawee; Sallepan, Maliwan; Charoenwattana, Sukanya

    2011-01-01

    Aim of this study was to evaluate the short term effect of coffee drinking on energy utilization in sedentary men. This study was performed in healthy sedentary men, who were randomized into three groups, control (n = 6), decaffeinated (n = 10), and caffeine (n = 10). The caffeine dose in coffee was rechecked and calculated for individual volunteers at 5 mg/kg. Baseline before drinking, complete blood count (CBC), glucose, antioxidant capacity, lipid peroxide, and caffeine in blood was evaluated. After drinking coffee for 1 hr, the submaximal exercise test with a modified Bruce protocol was carried out, and the VO2 and RER were analyzed individually at 80% maximal heart rate, then the blood was repeat evaluated. Three groups showed a nonsignificant difference in CBC results and physical characteristics. The caffeine group showed significant changes in all parameters; higher VO2 levels, (P = 0.037) and lower RER (P = 0.047), when compared to the baseline. Furthermore, the glucose level after exercise test increased significantly (P = 0.033) as well as lipid peroxide levels (P = 0.005), whereas antioxidant capacity did not change significantly (P = 0.759), when compared to the before exercise testing. In addition, the blood caffeine level also increased only in the caffeine group (P = 0.008). Short consumption of caffeinated coffee (5 mg/kg of caffeine), improves energy utilization and relates to glucose derivation and lipid oxidation.

  14. The Effect of Submaximal Exercise Preceded by Single Whole-Body Cryotherapy on the Markers of Oxidative Stress and Inflammation in Blood of Volleyball Players

    Science.gov (United States)

    Mila-Kierzenkowska, Celestyna; Szpinda, Michał; Augustyńska, Beata; Woźniak, Bartosz

    2013-01-01

    The aim of the study was to determine the effect of single whole-body cryotherapy (WBC) session applied prior to submaximal exercise on the activity of antioxidant enzymes, the concentration of lipid peroxidation products, total oxidative status, and the level of cytokines in blood of volleyball players. The study group consisted of 18 male professional volleyball players, who were subjected to extremely cold air (−130°C) prior to exercise performed on cycloergometer. Blood samples were taken five times: before WBC, after WBC procedure, after exercise preceded by cryotherapy (WBC exercise), and before and after exercise without WBC (control exercise). The activity of catalase statistically significantly increased after control exercise. Moreover, the activity of catalase and superoxide dismutase was lower after WBC exercise than after control exercise (P cryotherapy prior to exercise may have some antioxidant and anti-inflammatory properties. The relations between the level of studied oxidative stress and inflammatory markers may testify to the contribution of reactive oxygen species in cytokines release into the blood system in response to exercise and WBC. PMID:24489985

  15. The Effect of Submaximal Exercise Preceded by Single Whole-Body Cryotherapy on the Markers of Oxidative Stress and Inflammation in Blood of Volleyball Players

    Directory of Open Access Journals (Sweden)

    Celestyna Mila-Kierzenkowska

    2013-01-01

    Full Text Available The aim of the study was to determine the effect of single whole-body cryotherapy (WBC session applied prior to submaximal exercise on the activity of antioxidant enzymes, the concentration of lipid peroxidation products, total oxidative status, and the level of cytokines in blood of volleyball players. The study group consisted of 18 male professional volleyball players, who were subjected to extremely cold air (−130∘C prior to exercise performed on cycloergometer. Blood samples were taken five times: before WBC, after WBC procedure, after exercise preceded by cryotherapy (WBC exercise, and before and after exercise without WBC (control exercise. The activity of catalase statistically significantly increased after control exercise. Moreover, the activity of catalase and superoxide dismutase was lower after WBC exercise than after control exercise (P<0.001. After WBC exercise, the level of IL-6 and IL-1β was also lower (P<0.001 than after control exercise. The obtained results may suggest that cryotherapy prior to exercise may have some antioxidant and anti-inflammatory properties. The relations between the level of studied oxidative stress and inflammatory markers may testify to the contribution of reactive oxygen species in cytokines release into the blood system in response to exercise and WBC.

  16. VO2 kinetics of constant-load exercise following bed-rest-induced deconditioning

    Science.gov (United States)

    Convertino, V. A.; Goldwater, D. J.; Sandler, H.

    1984-01-01

    Previous studies have shown that the oxygen uptake kinetics during exercise and recovery may be changed by alterations in work intensity, prior exercise, muscle group involvement, ambient conditions, posture, disease state, and level of physical conditioning. However, the effects of detraining on oxygen uptake kinetics have not been determined. The present investigation has the objective to determine the effects of deconditioning following seven days of continuous head-down bed rest on changes in steady-state oxygen uptake, O2 deficit, and recovery oxygen uptake during the performance of constant-load exercise. The obtained results may provide support for previous proposals that submaximal oxygen uptake was significantly reduced following bed rest. The major finding was that bed-rest deconditioning resulted in a reduction of total O2 transport/utilization capacity during the transient phase of upright but not supine exercise.

  17. Effects of Dietary Acid Load on Exercise Metabolism and Anaerobic Exercise Performance

    Directory of Open Access Journals (Sweden)

    Susan L. Caciano, Cynthia L. Inman, Elizabeth E. Gockel-Blessing, Edward P. Weiss

    2015-06-01

    Full Text Available Dietary acid load, quantified as the potential renal acid load (PRAL of the diet, affects systemic pH and acid-base regulation. In a previous cross-sectional study, we reported that a low dietary PRAL (i.e. alkaline promoting diet is associated with higher respiratory exchange ratio (RER values during maximal exercise. The purpose of the present study was to confirm the previous findings with a short-term dietary intervention study. Additionally, we sought to determine if changes in PRAL affects submaximal exercise RER (as a reflection of substrate utilization and anaerobic exercise performance. Subjects underwent a graded treadmill exercise test (GXT to exhaustion and an anaerobic exercise performance test on two occasions, once after following a low-PRAL diet and on a separate occasion, after a high-PRAL diet. The diets were continued as long as needed to achieve an alkaline or acid fasted morning urine pH, respectively, with all being 4-9 days in duration. RER was measured during the GXT with indirect calorimetry. The anaerobic performance test was a running time-to-exhaustion test lasting 1-4 min. Maximal exercise RER was lower in the low-PRAL trial compared to the high-PRAL trial (1.10 ± 0.02 vs. 1.20 ± 0.05, p = 0.037. The low-PRAL diet also resulted in a 21% greater time to exhaustion during anaerobic exercise (2.56 ± 0.36 vs. 2.11 ± 0.31 sec, p = 0.044 and a strong tendency for lower RER values during submaximal exercise at 70% VO2max (0.88 ± 0.02 vs. 0.96 ± 0.04, p = 0.060. Contrary to our expectations, a short-term low-PRAL (alkaline promoting diet resulted in lower RER values during maximal-intensity exercise. However, the low-PRAL diet also increased anaerobic exercise time to exhaustion and appears to have shifted submaximal exercise substrate utilization to favor lipid oxidation and spare carbohydrate, both of which would be considered favorable effects in the context of exercise performance.

  18. The Gravity-Loading countermeasure Skinsuit (GLCS) and its effect upon aerobic exercise performance

    Science.gov (United States)

    Attias, Julia; Philip, A. T. Carvil; Waldie, James; Russomano, Thais; Simon, N. Evetts; David, A. Green

    2017-03-01

    The Russian Pingvin suit is employed as a countermeasure to musculoskeletal atrophy in microgravity, though its 2-stage loading regime is poorly tolerated. The Gravity-Loading Countermeasure Skinsuit (GLCS) has been devised to comfortably compress the body via incrementally increasing longitudinal elastic-fibre tensions from the shoulders to the feet. We tested whether the Mk III GLCS was a feasible adjunct to sub-maximal aerobic exercise and resulting VO2Max predictions. Eight healthy subjects (5♂, 28±6 yr) performed cycle ergometry at 75% VO2Max (derived from an Astrand-Rhyming protocol) whilst wearing a GLCS and gym clothing (GYM). Ventilatory parameters, heart rate (HR), core temperature (TC), and blood lactate (BL) were recorded along with subjective perceived exertion, thermal comfort, movement discomfort and body control. Physiological and subjective responses were compared over TIME and between GYM and GLCS (ATTIRE) with 2-way repeated measures ANOVA and Wilcoxon tests respectively. Resultant VO2Max predictions were compared with paired t-tests between ATTIRE. The GLCS induced greater initial exercise ventilatory responses which stabilised by 20 min. HR and TC continued to rise from 5 min irrespective of ATTIRE, whereas BL was greater in the GLCS at 20 min. Predicted V O2Max did not differ with ATTIRE, though some observed differences in HR were noteworthy. All subjective ratings were exacerbated in the GLCS. Despite increased perception of workload and initial ventilatory augmentations, submaximal exercise performance was not impeded. Whilst predicted VO2Max did not differ, determination of actual VO2Max in the GLCS is warranted due to apparent modulation of the linear HR-VO2 relationship. The GLCS may be a feasible adjunct to exercise and potential countermeasure to unloaded-induced physiological deconditioning on Earth or in space.

  19. The Effect of Lower-Body Positive Pressure on the Cardiorespiratory Response at Rest and during Submaximal Running Exercise

    Directory of Open Access Journals (Sweden)

    Frédéric Stucky

    2018-01-01

    Full Text Available Anti-gravity treadmills facilitate locomotion by lower-body positive pressure (LBPP. Effects on cardiorespiratory regulation are unknown. Healthy men (30 ± 8 y, 178.3 ± 5.7 cm, 70.3 ± 8.0 kg; mean ± SD stood upright (n = 10 or ran (n = 9 at 9, 11, 13, and 15 km.h−1 (5 min stages with LBPP (0, 15, 40 mmHg. Cardiac output (CO, stroke volume (SV, heart rate (HR, blood pressure (BP, peripheral resistance (PR, and oxygen uptake (VO2 were monitored continuously. During standing, LBPP increased SV [by +29 ± 13 (+41% and +42 ± 15 (+60% ml, at 15 and 40 mmHg, respectively (p < 0.05] and decreased HR [by −15 ± 6 (−20% and −22 ± 9 (−29% bpm (p < 0.05] resulting in a transitory increase in CO [by +1.6 ± 1.0 (+32% and +2.0 ± 1.0 (+39% l.min−1 (p < 0.05] within the first seconds of LBPP. This was accompanied by a transitory decrease in end-tidal PO2 [by −5 ± 3 (−5% and −10 ± 4 (−10% mmHg (p < 0.05] and increase in VO2 [by +66 ± 53 (+26% and +116 ± 64 (+46% ml.min−1 (p < 0.05], suggesting increased venous return and pulmonary blood flow. The application of LBPP increased baroreflex sensitivity (BRS [by +1.8 ± 1.6 (+18% and +4.6 ± 3.7 (+47% at 15 and 40 mmHg LBPP, respectively P < 0.05]. After reaching steady-state exercise CO vs. VO2 relationships remained linear with similar slope and intercept for each participant (mean R2 = 0.84 ± 0.13 while MAP remained unchanged. It follows that (1 LBPP affects cardiorespiratory integration at the onset of exercise; (2 at a given LBPP, once reaching steady-state exercise, the cardiorespiratory load is reduced proportionally to the lower metabolic demand resulting from the body weight support; (3 the balance between cardiovascular response, oxygen delivery to the exercising muscles and blood pressure regulation is maintained at exercise steady-state; and (4 changes in baroreflex sensitivity may be involved in the regulation of cardiovascular parameters during LBPP.

  20. Trunk muscle activation in the back and hack squat at the same relative loads.

    Science.gov (United States)

    Clark, David R; Lambert, Michael I; Hunter, Angus M

    2017-07-12

    The hack squat (HS) is likely to produce a greater 1 repetition maximum (1RM) compared to the back squat (BS). This can be attributed to the support of the trunk during the HS compared to no support during BS. This support however, may compromise trunk muscle activation (TMA), therefore producing different training adaptations. Accordingly, the purpose of this study was to compare 1RM in BS and HS and TMA at 4 relative loads, 65, 75, 85 and 95% of maximal system mass. Ten males completed 3 test sessions:1) BS and HS 1RM, 2) HS & BS neuromuscular test familiarization, and, 3) Neuromuscular test for 3 reps at 4 loads for BS and HS. BS TMA was significantly greater (p<0.05) than HS for all muscles and phases except rectus abdominus in concentric phase. TMA increased (p<0.05) with load in all muscles for both exercises and phases apart from lumbar sacral erector spinae in HS eccentric phase. Mean HS 1RM and submaximal loads were significantly (p<0.0001) higher than the equivalent BS loads. Duration of the eccentric phase was higher (p<0.01) in HS than BS but not different in concentric phase. Duration increased significantly (p<0.01) with load in both exercises and both phases. Despite higher absolute tests loads in HS, TMA was higher in BS. TMA is sensitive to load in both exercises. BS is more effective than HS in activating the muscles of the trunk and therefore arguably more effective in developing trunk strength and stability for dynamic athletic performance.

  1. Carbohydrate-Loading Diet

    Science.gov (United States)

    ... of your calories from carbohydrates. The role of carbohydrates Carbohydrates, also known as starches and sugars, are ... to consume some energy sources during your event. Carbohydrate loading Carbohydrate loading is done the week before ...

  2. Effects of dietary Acid load on exercise metabolism and anaerobic exercise performance.

    Science.gov (United States)

    Caciano, Susan L; Inman, Cynthia L; Gockel-Blessing, Elizabeth E; Weiss, Edward P

    2015-06-01

    Dietary acid load, quantified as the potential renal acid load (PRAL) of the diet, affects systemic pH and acid-base regulation. In a previous cross-sectional study, we reported that a low dietary PRAL (i.e. alkaline promoting diet) is associated with higher respiratory exchange ratio (RER) values during maximal exercise. The purpose of the present study was to confirm the previous findings with a short-term dietary intervention study. Additionally, we sought to determine if changes in PRAL affects submaximal exercise RER (as a reflection of substrate utilization) and anaerobic exercise performance. Subjects underwent a graded treadmill exercise test (GXT) to exhaustion and an anaerobic exercise performance test on two occasions, once after following a low-PRAL diet and on a separate occasion, after a high-PRAL diet. The diets were continued as long as needed to achieve an alkaline or acid fasted morning urine pH, respectively, with all being 4-9 days in duration. RER was measured during the GXT with indirect calorimetry. The anaerobic performance test was a running time-to-exhaustion test lasting 1-4 min. Maximal exercise RER was lower in the low-PRAL trial compared to the high-PRAL trial (1.10 ± 0.02 vs. 1.20 ± 0.05, p = 0.037). The low-PRAL diet also resulted in a 21% greater time to exhaustion during anaerobic exercise (2.56 ± 0.36 vs. 2.11 ± 0.31 sec, p = 0.044) and a strong tendency for lower RER values during submaximal exercise at 70% VO2max (0.88 ± 0.02 vs. 0.96 ± 0.04, p = 0.060). Contrary to our expectations, a short-term low-PRAL (alkaline promoting) diet resulted in lower RER values during maximal-intensity exercise. However, the low-PRAL diet also increased anaerobic exercise time to exhaustion and appears to have shifted submaximal exercise substrate utilization to favor lipid oxidation and spare carbohydrate, both of which would be considered favorable effects in the context of exercise performance. Key pointsShort-term (4-9 days) changes in

  3. Estimate of the 3,5 MMOL.L-¹ lactate threshold by maximal and submaximal variables during treadmill incremental test

    Directory of Open Access Journals (Sweden)

    Maria Kiss

    2006-03-01

    Full Text Available In predictive models, there is a lack of studies that have associated maximal and submaximal variables to attain lactate threshold (LT. Therefore, the purpose of this paper was to investigate the possibility for predicting 3.5 mmol.l-1 LT velocity (V3.5 using maximal and submaximal variables. The heart rate (HR corresponding to 12 km.h-1 velocity (HR12, the peak heart rate (HRPEAK, the velocity corresponding to HR of 170 bpm (V170 and the peak velocity (VPEAK were the independent variables used. Forty-six runners underwent to progressive test with initial velocity between 6 and 10.8 km.h-1, and increments of 1.2 km.h-1 every three minutes. The subjects were randomly assigned to validation group (n= 30 or cross-validation group (n= 16. Multiple regression analysis (Enter selection resulted in the following predictive equation (p RESUMO Em modelos preditivos, há uma ausência de estudos que tenham associado variáveis máximas e submáximas para a obtenção dos limiares de lactato. Desta maneira, o objetivo deste estudo foi verificar a possibilidade de estimativa do limiar de lactato, referente à concentração de lactato sangüíneo de 3,5 mmol.l-1 (LL3,5, a partir de variáveis máximas e submáximas obtidas em protocolo progressivo, em esteira rolante. Como variáveis preditoras, foram utilizadas a freqüência cardíaca (FC referente à velocidade de 12 km.h-1 (FC12, a FC de pico (FCPICO, a velocidade correspondente à FC de 170 bpm (VEL170 e a velocidade de pico (VELPICO. Após executar protocolo progressivo, com velocidade inicial entre 6,0 e 10,8 km.h-1, e incrementos de 1,2 km.h-1 a cada estágio de 3 minutos 5, 46 atletas aeróbios foram divididos aleatoriamente em grupo de validação (n= 30 e grupo de validação cruzada (n= 16. A análise de regressão múltipla (método Enter resultou na seguinte equação de predição (p< 0,05: LL3,5 (km.h1= -3,650 + (1,042 x VELPICO, com EPE de 1,2 km.h1 (7,7% e R² de 0,74. Não houve diferen

  4. Cold exposure enhances fat utilization but not non-esterified fatty acids, glycerol or catecholamines availability during submaximal walking and running.

    Science.gov (United States)

    Gagnon, Dominique D; Rintamäki, Hannu; Gagnon, Sheila S; Cheung, Stephen S; Herzig, Karl-Heinz; Porvari, Katja; Kyröläinen, Heikki

    2013-01-01

    Cold exposure modulates the use of carbohydrates (CHOs) and fat during exercise. This phenomenon has mostly been observed in controlled cycling studies, but not during walking and running when core temperature and oxygen consumption are controlled, as both may alter energy metabolism. This study aimed at examining energy substrate availability and utilization during walking and running in the cold when core temperature and oxygen consumption are maintained. Ten lightly clothed male subjects walked or ran for 60-min, at 50% and 70% of maximal oxygen consumption, respectively, in a climatic chamber set at 0°C or 22°C. Thermal, cardiovascular, and oxidative responses were measured every 15-min during exercise. Blood samples for serum non-esterified fatty acids (NEFAs), glycerol, glucose, beta-hydroxybutyrate (BHB), plasma catecholamines, and serum lipids were collected immediately prior, and at 30- and 60-min of exercise. Skin temperature strongly decreased while core temperature did not change during cold trials. Heart rate (HR) was also lower in cold trials. A rise in fat utilization in the cold was seen through lower respiratory quotient (RQ) (-0.03 ± 0.02), greater fat oxidation (+0.14 ± 0.13 g · min(-1)) and contribution of fat to total energy expenditure (+1.62 ± 1.99 kcal · min(-1)). No differences from cold exposure were observed in blood parameters. During submaximal walking and running, a greater reliance on derived fat sources occurs in the cold, despite the absence of concurrent alterations in NEFAs, glycerol, or catecholamine concentrations. This disparity may suggest a greater reliance on intra-muscular energy sources such as triglycerides during both walking and running.

  5. Cold exposure enhances fat utilization but not non-esterified fatty acids, glycerol or catecholamines availability during submaximal walking and running

    Directory of Open Access Journals (Sweden)

    Dominique Daniel Gagnon

    2013-05-01

    Full Text Available Cold exposure modulates the use of carbohydrates and fat during exercise. This phenomenon has mostly been observed in controlled cycling studies, but not during walking and running when core temperature and oxygen consumption are controlled, as both may alter energy metabolism. This study aimed at examining energy substrate availability and utilization during walking and running in the cold when core temperature and oxygen consumption are maintained. Ten lightly clothed male subjects walked or ran for 60-min, at 50% and 70% of maximal oxygen consumption, respectively, in a climatic chamber set at 0°C or 22°C. Thermal, cardiovascular, and oxidative responses were measured every 15-min during exercise. Blood samples for serum non-esterified fatty acids, glycerol, glucose, beta-hydroxybutyrate, plasma catecholamines, and serum lipids were collected immediately prior, and at 30- and 60-min of exercise. Skin temperature strongly decreased while core temperature did not change during cold trials. Heart rate was also lower in cold trials. A rise in fat utilization in the cold was seen through lower respiratory quotient (-0.03 ± 0.02, greater fat oxidation (+0.14 ± 0.13 g•min-1 and contribution of fat to total energy expenditure (+1.62 ± 1.99 kcal•min-1. No differences from cold exposure were observed in blood parameters. During submaximal walking and running, a greater reliance on derived fat sources occurs in the cold, despite the absence of concurrent alterations in non-esterified fatty acids, glycerol, or catecholamine concentrations. This disparity may suggest a greater reliance on intra-muscular energy sources such as triglycerides during both walking and running.

  6. Spatial electric load forecasting

    CERN Document Server

    Willis, H Lee

    2002-01-01

    Spatial Electric Load Forecasting Consumer Demand for Power and ReliabilityCoincidence and Load BehaviorLoad Curve and End-Use ModelingWeather and Electric LoadWeather Design Criteria and Forecast NormalizationSpatial Load Growth BehaviorSpatial Forecast Accuracy and Error MeasuresTrending MethodsSimulation Method: Basic ConceptsA Detailed Look at the Simulation MethodBasics of Computerized SimulationAnalytical Building Blocks for Spatial SimulationAdvanced Elements of Computerized SimulationHybrid Trending-Simulation MethodsAdvanced

  7. Cognitive Load and Cooperation

    DEFF Research Database (Denmark)

    Døssing, Felix Sebastian; Piovesan, Marco; Wengström, Erik Roland

    2017-01-01

    We study the effect of intuitive and reflective processes on cooperation using cognitive load. Compared with time constraint, which has been used in the previous literature, cognitive load is a more direct way to block reflective processes, and thus a more suitable way to study the link between...... intuition and cooperation. Using a repeated public goods game, we study the effect of different levels of cognitive load on contributions. We show that a higher cognitive load increases the initial level of cooperation. In particular, subjects are significantly less likely to fully free ride under high...... cognitive load....

  8. Effect of resistive load on the inspiratory work and power of breathing during exertion.

    Directory of Open Access Journals (Sweden)

    Thomas Powell

    Full Text Available The resistive work of breathing against an external load during inspiration (WR(I was measured at the mouth, during sub-maximal exercise in healthy participants. This measure (which excludes the elastic work component allows the relationship between resistive work and power, ventilation and exercise modality to be explored. A total of 45 adult participants with healthy lung function took part in a series of exercise protocols, in which the relationship between WR(I, power of breathing, PR(I and minute ventilation, [Formula: see text] were assessed during rest, while treadmill walking or ergometer cycling, over a range of exercise intensities (up to 150 Watts and ventilation rates (up to 48 L min(-1 with applied constant resistive loads of 0.75 and 1.5 kPa.L.sec(-1. Resting WR(I was 0.12 JL(-1 and PR(I was 0.9 W. At each resistive load, independent of the breathing pattern or exercise mode, the WR(I increased in a linear fashion at 20 mJ per litre of [Formula: see text], while PR(I increased exponentially. With increasing resistive load the work and power at any given [Formula: see text] increased exponentially. Calculation of the power to work ratio during loaded breathing suggests that loads above 1.5 kPa.L.sec(-1 make the work of resistive breathing become inhibitive at even a moderate [Formula: see text] (>30 L sec(-1. The relationship between work done and power generated while breathing against resistive loads is independent of the exercise mode (cycling or walking and that ventilation is limited by the work required to breathe, rather than an inability to maintain or generate power.

  9. Optimisation of load control

    Energy Technology Data Exchange (ETDEWEB)

    Koponen, P. [VTT Energy, Espoo (Finland)

    1998-08-01

    Electricity cannot be stored in large quantities. That is why the electricity supply and consumption are always almost equal in large power supply systems. If this balance were disturbed beyond stability, the system or a part of it would collapse until a new stable equilibrium is reached. The balance between supply and consumption is mainly maintained by controlling the power production, but also the electricity consumption or, in other words, the load is controlled. Controlling the load of the power supply system is important, if easily controllable power production capacity is limited. Temporary shortage of capacity causes high peaks in the energy price in the electricity market. Load control either reduces the electricity consumption during peak consumption and peak price or moves electricity consumption to some other time. The project Optimisation of Load Control is a part of the EDISON research program for distribution automation. The following areas were studied: Optimization of space heating and ventilation, when electricity price is time variable, load control model in power purchase optimization, optimization of direct load control sequences, interaction between load control optimization and power purchase optimization, literature on load control, optimization methods and field tests and response models of direct load control and the effects of the electricity market deregulation on load control. An overview of the main results is given in this chapter

  10. Concentrated loads on concrete

    DEFF Research Database (Denmark)

    Lorenzen, Karen Grøndahl; Nielsen, Mogens Peter

    1997-01-01

    This report deals with concentrated loads on concrete.A new upper bound solution in the axisymmetrical case of a point load in the center of the end face of a cylinder is developed.Based on previous work dealing with failure mechanisms and upper bound solutions, new approximate formulas are devel......This report deals with concentrated loads on concrete.A new upper bound solution in the axisymmetrical case of a point load in the center of the end face of a cylinder is developed.Based on previous work dealing with failure mechanisms and upper bound solutions, new approximate formulas...

  11. Electrical load modeling

    Energy Technology Data Exchange (ETDEWEB)

    Valgas, Helio Moreira; Pinto, Roberto del Giudice R.; Franca, Carlos [Companhia Energetica de Minas Gerais (CEMIG), Belo Horizonte, MG (Brazil); Lambert-Torres, Germano; Silva, Alexandre P. Alves da; Pires, Robson Celso; Costa Junior, Roberto Affonso [Escola Federal de Engenharia de Itajuba, MG (Brazil)

    1994-12-31

    Accurate dynamic load models allow more precise calculations of power system controls and stability limits, which are critical mainly in the operation planning of power systems. This paper describes the development of a computer program (software) for static and dynamic load model studies using the measurement approach for the CEMIG system. Two dynamic load model structures are developed and tested. A procedure for applying a set of measured data from an on-line transient recording system to develop load models is described. (author) 6 refs., 17 figs.

  12. Critical Axial Load

    Directory of Open Access Journals (Sweden)

    Walt Wells

    2008-01-01

    Full Text Available Our objective in this paper is to solve a second order differential equation for a long, simply supported column member subjected to a lateral axial load using Heun's numerical method. We will use the solution to find the critical load at which the column member will fail due to buckling. We will calculate this load using Euler's derived analytical approach for an exact solution, as well as Euler's Numerical Method. We will then compare the three calculated values to see how much they deviate from one another. During the critical load calculation, it will be necessary to calculate the moment of inertia for the column member.

  13. Balance in single-limb stance in healthy subjects – reliability of testing procedure and the effect of short-duration sub-maximal cycling

    Directory of Open Access Journals (Sweden)

    Roberts David

    2003-06-01

    Full Text Available Abstract Background To assess balance in single-limb stance, center of pressure movements can be registered by stabilometry with force platforms. This can be used for evaluation of injuries to the lower extremities. It is important to ensure that the assessment tools we use in the clinical setting and in research have minimal measurement error. Previous studies have shown that the ability to maintain standing balance is decreased by fatiguing exercise. There is, however, a need for further studies regarding possible effects of general exercise on balance in single-limb stance. The aims of this study were: 1 to assess the test-retest reliability of balance variables measured in single-limb stance on a force platform, and 2 to study the effect of exercise on balance in single-limb stance, in healthy subjects. Methods Forty-two individuals were examined for test-retest reliability, and 24 individuals were tested before (pre-exercise and after (post-exercise short-duration, sub-maximal cycling. Amplitude and average speed of center of pressure movements were registered in the frontal and sagittal planes. Mean difference between test and retest with 95% confidence interval, the intraclass correlation coefficient, and the Bland and Altman graphs with limits of agreement, were used as statistical methods for assessing test-retest reliability. The paired t-test was used for comparisons between pre- and post-exercise measurements. Results No difference was found between test and retest. The intraclass correlation coefficients ranged from 0.79 to 0.95 in all stabilometric variables except one. The limits of agreement revealed that small changes in an individual's performance cannot be detected. Higher values were found after cycling in three of the eight stabilometric variables. Conclusions The absence of systematic variation and the high ICC values, indicate that the test is reliable for distinguishing among groups of subjects. However, relatively large

  14. Load Induced Blindness

    Science.gov (United States)

    Macdonald, James S. P.; Lavie, Nilli

    2008-01-01

    Although the perceptual load theory of attention has stimulated a great deal of research, evidence for the role of perceptual load in determining perception has typically relied on indirect measures that infer perception from distractor effects on reaction times or neural activity (see N. Lavie, 2005, for a review). Here we varied the level of…

  15. Mechanism isolates load weighing cell during lifting of load

    Science.gov (United States)

    Haigler, J. S.

    1966-01-01

    Load weighing cell used in conjuction with a hoist is isolated during lifting and manipulation of the load. A simple mechanism, attached to a crane hook, provides a screw adjustment for engaging the load cell during weighing of the load and isolating it from lift forces during hoisting of the load.

  16. Load flow analysis using decoupled fuzzy load flow under critical ...

    African Journals Online (AJOL)

    user

    The conventional load flow methods like Newton-Raphson load flow (NRLF), Fast Decoupled load flow (FDLF) provide poor performance under critical conditions such as high R/X ratio, heavily loading condition etc. Exploiting the decoupling properties of power system, reliable fuzzy load flow is developed to overcome the ...

  17. Load Balancing Scientific Applications

    Energy Technology Data Exchange (ETDEWEB)

    Pearce, Olga Tkachyshyn [Texas A & M Univ., College Station, TX (United States)

    2014-12-01

    The largest supercomputers have millions of independent processors, and concurrency levels are rapidly increasing. For ideal efficiency, developers of the simulations that run on these machines must ensure that computational work is evenly balanced among processors. Assigning work evenly is challenging because many large modern parallel codes simulate behavior of physical systems that evolve over time, and their workloads change over time. Furthermore, the cost of imbalanced load increases with scale because most large-scale scientific simulations today use a Single Program Multiple Data (SPMD) parallel programming model, and an increasing number of processors will wait for the slowest one at the synchronization points. To address load imbalance, many large-scale parallel applications use dynamic load balance algorithms to redistribute work evenly. The research objective of this dissertation is to develop methods to decide when and how to load balance the application, and to balance it effectively and affordably. We measure and evaluate the computational load of the application, and develop strategies to decide when and how to correct the imbalance. Depending on the simulation, a fast, local load balance algorithm may be suitable, or a more sophisticated and expensive algorithm may be required. We developed a model for comparison of load balance algorithms for a specific state of the simulation that enables the selection of a balancing algorithm that will minimize overall runtime.

  18. Greater Neural Adaptations following High- vs. Low-Load Resistance Training.

    Science.gov (United States)

    Jenkins, Nathaniel D M; Miramonti, Amelia A; Hill, Ethan C; Smith, Cory M; Cochrane-Snyman, Kristen C; Housh, Terry J; Cramer, Joel T

    2017-01-01

    We examined the neuromuscular adaptations following 3 and 6 weeks of 80 vs. 30% one repetition maximum (1RM) resistance training to failure in the leg extensors. Twenty-six men (age = 23.1 ± 4.7 years) were randomly assigned to a high- (80% 1RM; n = 13) or low-load (30% 1RM; n = 13) resistance training group and completed leg extension resistance training to failure 3 times per week for 6 weeks. Testing was completed at baseline, 3, and 6 weeks of training. During each testing session, ultrasound muscle thickness and echo intensity, 1RM strength, maximal voluntary isometric contraction (MVIC) strength, and contractile properties of the quadriceps femoris were measured. Percent voluntary activation (VA) and electromyographic (EMG) amplitude were measured during MVIC, and during randomly ordered isometric step muscle actions at 10-100% of baseline MVIC. There were similar increases in muscle thickness from Baseline to Week 3 and 6 in the 80 and 30% 1RM groups. However, both 1RM and MVIC strength increased from Baseline to Week 3 and 6 to a greater degree in the 80% than 30% 1RM group. VA during MVIC was also greater in the 80 vs. 30% 1RM group at Week 6, and only training at 80% 1RM elicited a significant increase in EMG amplitude during MVIC. The peak twitch torque to MVIC ratio was also significantly reduced in the 80%, but not 30% 1RM group, at Week 3 and 6. Finally, VA and EMG amplitude were reduced during submaximal torque production as a result of training at 80% 1RM, but not 30% 1RM. Despite eliciting similar hypertrophy, 80% 1RM improved muscle strength more than 30% 1RM, and was accompanied by increases in VA and EMG amplitude during maximal force production. Furthermore, training at 80% 1RM resulted in a decreased neural cost to produce the same relative submaximal torques after training, whereas training at 30% 1RM did not. Therefore, our data suggest that high-load training results in greater neural adaptations that may explain the disparate increases in

  19. Greater Neural Adaptations following High- vs. Low-Load Resistance Training

    Directory of Open Access Journals (Sweden)

    Nathaniel D. M. Jenkins

    2017-05-01

    Full Text Available We examined the neuromuscular adaptations following 3 and 6 weeks of 80 vs. 30% one repetition maximum (1RM resistance training to failure in the leg extensors. Twenty-six men (age = 23.1 ± 4.7 years were randomly assigned to a high- (80% 1RM; n = 13 or low-load (30% 1RM; n = 13 resistance training group and completed leg extension resistance training to failure 3 times per week for 6 weeks. Testing was completed at baseline, 3, and 6 weeks of training. During each testing session, ultrasound muscle thickness and echo intensity, 1RM strength, maximal voluntary isometric contraction (MVIC strength, and contractile properties of the quadriceps femoris were measured. Percent voluntary activation (VA and electromyographic (EMG amplitude were measured during MVIC, and during randomly ordered isometric step muscle actions at 10–100% of baseline MVIC. There were similar increases in muscle thickness from Baseline to Week 3 and 6 in the 80 and 30% 1RM groups. However, both 1RM and MVIC strength increased from Baseline to Week 3 and 6 to a greater degree in the 80% than 30% 1RM group. VA during MVIC was also greater in the 80 vs. 30% 1RM group at Week 6, and only training at 80% 1RM elicited a significant increase in EMG amplitude during MVIC. The peak twitch torque to MVIC ratio was also significantly reduced in the 80%, but not 30% 1RM group, at Week 3 and 6. Finally, VA and EMG amplitude were reduced during submaximal torque production as a result of training at 80% 1RM, but not 30% 1RM. Despite eliciting similar hypertrophy, 80% 1RM improved muscle strength more than 30% 1RM, and was accompanied by increases in VA and EMG amplitude during maximal force production. Furthermore, training at 80% 1RM resulted in a decreased neural cost to produce the same relative submaximal torques after training, whereas training at 30% 1RM did not. Therefore, our data suggest that high-load training results in greater neural adaptations that may explain the

  20. Sensorimotor modulation differs with load type during constant finger force or position.

    Directory of Open Access Journals (Sweden)

    Hikari Kirimoto

    Full Text Available During submaximal isometric contraction, there are two different load types: production of a constant force against a rigid restraint (force task, and maintenance of position against a constant load (position task. Previous studies reported that the time to task failure during a fatigue task was twice as long in the force task compared with the position task. Sensory feedback processing may contribute to these differences. The purpose of the current study was to determine the influence of load types during static muscle contraction tasks on the gating effect, i.e., attenuation of somatosensory-evoked potentials (SEPs and the cortical silent period (cSP. Ten healthy subjects contracted their right first dorsal interosseus muscle by abducting their index finger for 90 s, to produce a constant force against a rigid restraint that was 20% of the maximum voluntary contraction (force task, or to maintain a constant position with 10° abduction of the metacarpophalangeal joint against the same load (position task. Somatosensory evoked potentials (SEPs were recorded from C3' by stimulating either the right ulnar or median nerve at the wrist while maintaining contraction. The cortical silent period (cSP was also elicited by transcranial magnetic stimulation. Reduction of the amplitude of the P45 component of SEPs was significantly larger during the position task than during the force task and under control rest conditions when the ulnar nerve, but not the median nerve, was stimulated. The position task had a significantly shorter cSP duration than the force task. These results suggest the need for more proprioceptive information during the position task than the force task. The shorter duration of the cSP during the position task may be attributable to larger amplitude of heteronymous short latency reflexes. Sensorimotor modulations may differ with load type during constant finger force or position tasks.

  1. LOADING SIMULATION PROGRAM C

    Data.gov (United States)

    U.S. Environmental Protection Agency — LSPC is the Loading Simulation Program in C++, a watershed modeling system that includes streamlined Hydrologic Simulation Program Fortran (HSPF) algorithms for...

  2. Plug Load Data

    Data.gov (United States)

    National Aeronautics and Space Administration — We provide MATLAB binary files (.mat) and comma separated values files of data collected from a pilot study of a plug load management system that allows for the...

  3. LOADING SIMULATION PROGRAM C

    Science.gov (United States)

    LSPC is the Loading Simulation Program in C++, a watershed modeling system that includes streamlined Hydrologic Simulation Program Fortran (HSPF) algorithms for simulating hydrology, sediment, and general water quality

  4. HIV Viral Load

    Science.gov (United States)

    ... Chains Sex Hormone Binding Globulin (SHBG) Shiga toxin-producing Escherichia coli Sickle Cell Tests Sirolimus Smooth Muscle ... used each time. Will exercise, nutrition, and other lifestyle modifications help decrease my HIV viral load? There ...

  5. Lumbriculus variegatus loading study

    Data.gov (United States)

    U.S. Environmental Protection Agency — Results from sediment bioaccumulation tests with Lumbriculus variegatus with evaluating the effects of organism loading density. This dataset is associated with the...

  6. Static Loads Test Facility

    Data.gov (United States)

    Federal Laboratory Consortium — FUNCTION: Provides the capability to perform large-scale structural loads testing on spacecraft and other structures. Results from these tests can be used to verify...

  7. Composite Load Model Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Ning; Qiao, Hong (Amy)

    2007-09-30

    The WECC load modeling task force has dedicated its effort in the past few years to develop a composite load model that can represent behaviors of different end-user components. The modeling structure of the composite load model is recommended by the WECC load modeling task force. GE Energy has implemented this composite load model with a new function CMPLDW in its power system simulation software package, PSLF. For the last several years, Bonneville Power Administration (BPA) has taken the lead and collaborated with GE Energy to develop the new composite load model. Pacific Northwest National Laboratory (PNNL) and BPA joint force and conducted the evaluation of the CMPLDW and test its parameter settings to make sure that: • the model initializes properly, • all the parameter settings are functioning, and • the simulation results are as expected. The PNNL effort focused on testing the CMPLDW in a 4-bus system. An exhaustive testing on each parameter setting has been performed to guarantee each setting works. This report is a summary of the PNNL testing results and conclusions.

  8. Load power device, system and method of load control and management employing load identification

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Yi; Luebke, Charles John; Schoepf, Thomas J.

    2018-01-09

    A load power device includes a power input, at least one power output for at least one load, a plurality of sensors structured to sense voltage and current at the at least one power output, and a processor. The processor provides: (a) load identification based upon the sensed voltage and current, and (b) load control and management based upon the load identification.

  9. Methods of Monitoring Training Load and Their Relationships to Changes in Fitness and Performance in Competitive Road Cyclists.

    Science.gov (United States)

    Sanders, Dajo; Abt, Grant; Hesselink, Matthijs K C; Myers, Tony; Akubat, Ibrahim

    2017-05-01

    To assess the dose-response relationships between different training-load methods and aerobic fitness and performance in competitive road cyclists. Training data from 15 well-trained competitive cyclists were collected during a 10-wk (December-March) preseason training period. Before and after the training period, participants underwent a laboratory incremental exercise test with gas-exchange and lactate measures and a performance assessment using an 8-min time trial (8MT). Internal training load was calculated using Banister TRIMP, Edwards TRIMP, individualized TRIMP (iTRIMP), Lucia TRIMP (luTRIMP), and session rating of perceived exertion (sRPE). External load was measured using Training Stress Score (TSS). Large to very large relationships (r = .54-.81) between training load and changes in submaximal fitness variables (power at 2 and 4 mmol/L) were observed for all training-load calculation methods. The strongest relationships with changes in aerobic fitness variables were observed for iTRIMP (r = .81 [95% CI .51-.93, r = .77 [95% CI .43-.92]) and TSS (r = .75 [95% CI .31-.93], r = .79 [95% CI .40-.94]). The strongest dose-response relationships with changes in the 8MT test were observed for iTRIMP (r = .63 [95% CI .17-.86]) and luTRIMP (r = .70 [95% CI .29-.89). Training-load quantification methods that integrate individual physiological characteristics have the strongest dose-response relationships, suggesting this to be an essential factor in the quantification of training load in cycling.

  10. Dielectrically Loaded Biconical Antennas

    Science.gov (United States)

    Nusseibeh, Fouad Ahmed

    1995-01-01

    Biconical antennas are of great interest to those who deal with broadband applications including the transmission/reception of pulses. In particular, wide-angle conical antennas are an attractive choice in many applications including Electronic Support Measures (ESM) and the measurements of transient surface currents and charge densities on aircraft. Dielectric loading in the interior region of a conical antenna can be used to reduce the size of the antenna especially at low frequencies and/or for structural strength. Therefore, having an analytical solution for the input impedance and the frequency response is very helpful in optimizing the design and understanding the behavior of the antenna. From the quasi-analytical solution for the input impedance and the electric field of a wide-angle conical antenna, it can be seen that the dielectric loading in the antenna region improves the input impedance at low frequencies, but increases the number of resonance points and the magnitude of these peaks. When an inhomogeneous dielectric load is used, the magnitude of the resonance peaks is decreased (depending on the way the load is distributed), improving the input impedance of the antenna significantly. Introducing a dielectric load in the interior region of an electrically short receiving cone makes the antenna behave as an electrically longer antenna. However, this is not true for the case for electrical1y long antennas. For the case of pulse transmission, the dielectric load affects only the amplitude. Of course, if the dielectric fills the whole space, both transmitting and receiving antennas behave as electrically longer antennas.

  11. Wave Loads on Cylinders

    DEFF Research Database (Denmark)

    Burcharth, H. F.; Frigaard, Peter

    1989-01-01

    Wave loads may be defined as time varying forces on a body resulting from the wave induced flow fields which surrounds the body in whole or in part. Such unsteady fluid forces are the net result of pressure and shear forces integrated over the instantaneous wetted area.......Wave loads may be defined as time varying forces on a body resulting from the wave induced flow fields which surrounds the body in whole or in part. Such unsteady fluid forces are the net result of pressure and shear forces integrated over the instantaneous wetted area....

  12. The Influence of Changes in Acute Training Load on Daily Sensitivity of Morning-Measured Fatigue Variables in Elite Soccer Players.

    Science.gov (United States)

    Thorpe, Robin T; Strudwick, Anthony J; Buchheit, Martin; Atkinson, Greg; Drust, Barry; Gregson, Warren

    2017-04-01

    To determine the sensitivity of a range of potential fatigue measures to daily training load accumulated over the previous 2, 3, and 4 d during a short in-season competitive period in elite senior soccer players (N = 10). Total highspeed-running distance, perceived ratings of wellness (fatigue, muscle soreness, sleep quality), countermovement-jump height (CMJ), submaximal heart rate (HRex), postexercise heart-rate recovery (HRR), and heart-rate variability (HRV: Ln rMSSD) were analyzed during an in-season competitive period (17 d). General linear models were used to evaluate the influence of 2-, 3-, and 4-d total high-speed-running-distance accumulation on fatigue measures. Fluctuations in perceived ratings of fatigue were correlated with fluctuations in total high-speed-running-distance accumulation covered on the previous 2 d (r = -.31; small), 3 d (r = -.42; moderate), and 4 d (r = -.28; small) (P training loads. Perceived ratings of fatigue and HRex were sensitive to fluctuations in acute total high-speed-running-distance accumulation, although sensitivity was not systematically influenced by the number of previous days over which the training load was accumulated. The present findings indicate that the sensitivity of morning-measured fatigue variables to changes in training load is generally not improved when compared with training loads beyond the previous day's training.

  13. Load research and load estimation in electricity distribution

    Energy Technology Data Exchange (ETDEWEB)

    Seppaelae, A. [VTT Energy, Espoo (Finland). Energy Systems

    1996-12-31

    The topics introduced in this thesis are: the Finnish load research project, a simple form customer class load model, analysis of the origins of customers load distribution, a method for the estimation of the confidence interval of customer loads and Distribution Load Estimation (DLE) which utilises both the load models and measurements from distribution networks. The Finnish load research project started in 1983. The project was initially coordinated by the Association of Finnish Electric Utilities and 40 utilities joined the project. Now there are over 1000 customer hourly load recordings in a database. A simple form customer class load model is introduced. The model is designed to be practical for most utility applications and has been used by the Finnish utilities for several years. The only variable of the model is the customers annual energy consumption. The model gives the customers average hourly load and standard deviation for a selected month, day and hour. The statistical distribution of customer loads is studied and a model for customer electric load variation is developed. The model results in a lognormal distribution as an extreme case. Using the `simple form load model`, a method for estimating confidence intervals (confidence limits) of customer hourly load is developed. The two methods selected for final analysis are based on normal and lognormal distribution estimated in a simplified manner. The estimation of several cumulated customer class loads is also analysed. Customer class load estimation which combines the information from load models and distribution network load measurements is developed. This method, called Distribution Load Estimation (DLE), utilises information already available in the utilities databases and is thus easy to apply

  14. Laterally loaded masonry

    DEFF Research Database (Denmark)

    Raun Gottfredsen, F.

    stress and increasing shear. The results show a transition to pure friction as the cohesion is gradually destroyed. An interface model of a mortar joint that can take into account this aspect has been developed. Laterally loaded masonry panels have also been tested and it is found to be characteristic...

  15. Fuel Load (FL)

    Science.gov (United States)

    Duncan C. Lutes; Robert E. Keane

    2006-01-01

    The Fuel Load method (FL) is used to sample dead and down woody debris, determine depth of the duff/ litter profile, estimate the proportion of litter in the profile, and estimate total vegetative cover and dead vegetative cover. Down woody debris (DWD) is sampled using the planar intercept technique based on the methodology developed by Brown (1974). Pieces of dead...

  16. Probabilistic Load Flow

    DEFF Research Database (Denmark)

    Chen, Peiyuan; Chen, Zhe; Bak-Jensen, Birgitte

    2008-01-01

    This paper reviews the development of the probabilistic load flow (PLF) techniques. Applications of the PLF techniques in different areas of power system steady-state analysis are also discussed. The purpose of the review is to identify different available PLF techniques and their corresponding...

  17. Robust surgery loading

    NARCIS (Netherlands)

    Hans, Elias W.; Wullink, Gerhard; van Houdenhoven, Mark; Kazemier, Geert

    2008-01-01

    We consider the robust surgery loading problem for a hospital’s operating theatre department, which concerns assigning surgeries and sufficient planned slack to operating room days. The objective is to maximize capacity utilization and minimize the risk of overtime, and thus cancelled patients. This

  18. Duration of load revisited

    DEFF Research Database (Denmark)

    Hoffmeyer, Preben; Sørensen, John Dalsgaard

    2007-01-01

    A duration of load study representing 13 years of testing was recently terminated. Preliminary results have been published over the years. This paper represents the final account of the study, which was focused on the influ-ence of moisture content on time to failure for structural timber subject...

  19. Load research manual. Volume 1. Load research procedures

    Energy Technology Data Exchange (ETDEWEB)

    Brandenburg, L.; Clarkson, G.; Grund, Jr., C.; Leo, J.; Asbury, J.; Brandon-Brown, F.; Derderian, H.; Mueller, R.; Swaroop, R.

    1980-11-01

    This three-volume manual presents technical guidelines for electric utility load research. Special attention is given to issues raised by the load data reporting requirements of the Public Utility Regulatory Policies Act of 1978 and to problems faced by smaller utilities that are initiating load research programs. In Volumes 1 and 2, procedures are suggested for determining data requirements for load research, establishing the size and customer composition of a load survey sample, selecting and using equipment to record customer electricity usage, processing data tapes from the recording equipment, and analyzing the data. Statistical techniques used in customer sampling are discussed in detail. The costs of load research also are estimated, and ongoing load research programs at three utilities are described. The manual includes guides to load research literature and glossaries of load research and statistical terms.

  20. Heavy-Load Lifting

    DEFF Research Database (Denmark)

    Bloomquist, Kira; Oturai, Peter; Steele, Megan L

    2017-01-01

    PURPOSE: Despite a paucity of evidence, prevention guidelines typically advise avoidance of heavy lifting in an effort to protect against breast cancer-related lymphedema. This study compared acute responses in arm swelling and related symptoms after low- and heavy-load resistance exercise among...... women at risk of lymphedema while receiving adjuvant taxane-based chemotherapy. METHODS: This is a randomized, cross-over equivalence trial. Women receiving adjuvant taxane-based chemotherapy for breast cancer who had undergone axillary lymph node dissection (n=21) participated in low- (60-65% 1...... repetition maximum (RM), two sets of 15-20 repetitions) and heavy-load (85-90% 1RM, three sets of 5-8 repetition) upper-extremity resistance exercise separated by a one-week wash-out period. Swelling was determined by bioimpedance spectroscopy and dual energy x-ray absorptiometry, with breast cancer...

  1. Load responsive hydrodynamic bearing

    Science.gov (United States)

    Kalsi, Manmohan S.; Somogyi, Dezso; Dietle, Lannie L.

    2002-01-01

    A load responsive hydrodynamic bearing is provided in the form of a thrust bearing or journal bearing for supporting, guiding and lubricating a relatively rotatable member to minimize wear thereof responsive to relative rotation under severe load. In the space between spaced relatively rotatable members and in the presence of a liquid or grease lubricant, one or more continuous ring shaped integral generally circular bearing bodies each define at least one dynamic surface and a plurality of support regions. Each of the support regions defines a static surface which is oriented in generally opposed relation with the dynamic surface for contact with one of the relatively rotatable members. A plurality of flexing regions are defined by the generally circular body of the bearing and are integral with and located between adjacent support regions. Each of the flexing regions has a first beam-like element being connected by an integral flexible hinge with one of the support regions and a second beam-like element having an integral flexible hinge connection with an adjacent support region. A least one local weakening geometry of the flexing region is located intermediate the first and second beam-like elements. In response to application of load from one of the relatively rotatable elements to the bearing, the beam-like elements and the local weakening geometry become flexed, causing the dynamic surface to deform and establish a hydrodynamic geometry for wedging lubricant into the dynamic interface.

  2. Training Load and Player Monitoring in High-Level Football: Current Practice and Perceptions.

    Science.gov (United States)

    Akenhead, Richard; Nassis, George P

    2016-07-01

    Training load (TL) is monitored with the aim of making evidence-based decisions on appropriate loading schemes to reduce injuries and enhance team performance. However, little is known in detail about the variables of load and methods of analysis used in high-level football. Therefore, the aim of this study was to provide information on the practices and practitioners' perceptions of monitoring in professional clubs. Eighty-two high-level football clubs from Europe, the United States, and Australia were invited to answer questions relating to how TL is quantified, how players' responses are monitored, and their perceptions of the effectiveness of monitoring. Forty-one responses were received. All teams used GPS and heart-rate monitors during all training sessions, and 28 used rating of perceived exertion. The top-5-ranking TL variables were acceleration (various thresholds), total distance, distance covered above 5.5 m/s, estimated metabolic power, and heart-rate exertion. Players' responses to training are monitored using questionnaires (68% of clubs) and submaximal exercise protocols (41%). Differences in expected vs actual effectiveness of monitoring were 23% and 20% for injury prevention and performance enhancement, respectively (P < .001 d = 1.0-1.4). Of the perceived barriers to effectiveness, limited human resources scored highest, followed by coach buy-in. The discrepancy between expected and actual effectiveness appears to be due to suboptimal integration with coaches, insufficient human resources, and concerns over the reliability of assessment tools. Future approaches should critically evaluate the usefulness of current monitoring tools and explore methods of reducing the identified barriers to effectiveness.

  3. Nutrient and Coliform Loading (NCL)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This is a database of available fecal coliform bacteria, fecal streptococci bacteria, and nutrient loading data. Loading for contaminants other than fecal coliform...

  4. Load Estimation from Modal Parameters

    DEFF Research Database (Denmark)

    Aenlle, Manuel López; Brincker, Rune; Fernández, Pelayo Fernández

    2007-01-01

    In Natural Input Modal Analysis the modal parameters are estimated just from the responses while the loading is not recorded. However, engineers are sometimes interested in knowing some features of the loading acting on a structure. In this paper, a procedure to determine the loading from a FRF...... the accuracy in the load estimation. Finally, the results of an experimental program carried out on a simple structure are presented....

  5. Research of Impact Load in Large Electrohydraulic Load Simulator

    Directory of Open Access Journals (Sweden)

    Yongguang Liu

    2014-01-01

    Full Text Available The stronger impact load will appear in the initial phase when the large electric cylinder is tested in the hardware-in-loop simulation. In this paper, the mathematical model is built based on AMESim, and then the reason of the impact load is investigated through analyzing the changing tendency of parameters in the simulation results. The inhibition methods of impact load are presented according to the structural invariability principle and applied to the actual system. The final experimental result indicates that the impact load is inhibited, which provides a good experimental condition for the electric cylinder and promotes the study of large load simulator.

  6. Pollution Load Estimation Based on Characteristic Section Load Method

    Science.gov (United States)

    Zhu, Lei; Song, JinXi; Liu, WanQing

    2017-12-01

    Weihe River Watershed above Linjiacun Section is taken as the research objective in this paper and COD is chosen as the water quality parameter. According to the discharge characteristics of point source pollutions and non-point source pollutions, a new method to estimate pollution loads-Characteristic Section Load Method(CSLM) is proposed and point source pollution and non-point source pollution loads of Weihe River Watershed above Linjiacun Section are calculated in the rainy, normal and dry season in the year 2007. The results show that the monthly point source pollution loads of Weihe River Watershed above Linjiacun Section are discharged stably, the monthly non-point source pollution loads of Weihe River Watershed above Linjiacun Section change greatly, the non-point source pollution load proportions of total pollution load of COD are gradually decreased in the rainy, normal and wet periods.

  7. Variação da pressão intraocular após teste submáximo de força no treinamento resistido Intraocular pressure variation after submaximal strength test in resistance training

    Directory of Open Access Journals (Sweden)

    Marcelo Conte

    2009-06-01

    Full Text Available OBJETIVO: Verificar a variação da pressão intraocular (PIO decorrente da aplicação do teste de predição para uma repetição máxima (1RM. MÉTODOS: Foram avaliados em estudo observacional 145 calouros (22,04 ± 4,17 anos; de ambos os sexos do curso de Educação Física da Escola Superior de Educação Física de Jundiaí (ESEFJ. Os critérios de exclusão foram: opacidade de meios, alteração de globo ocular ou ausência de globo ocular. Todos os participantes assinaram o Termo de Consentimento Livre e Esclarecido. A avaliação da PIO foi determinada por duas medidas consecutivas com o tonômetro de Perkins: i pré-teste: antes do teste de 1RM e ii pós-teste: logo após a realização do teste. O teste de 1RM consistiu em predizer o valor de uma repetição máxima através de repetições até a fadiga. Foram utilizados os seguintes exercícios resistidos: supino, pulley dorsal, desenvolvimento, rosca direta e leg press 45º. Como procedimento estatístico foi empregado o teste "t" de Student pareado. RESULTADOS: Ocorreu redução da PIO após a realização do teste de predição de 1RM: 13,48 ± 3,32 vs.10,20 ± 3,72 mmHg (pPURPOSE: To verify the intraocular pressure (IOP after sub-maximal strength test. METHODS: 145 Physical Education freshmen (22.04 ± 4.17 years old; female and male from Superior Physical Education School of Jundiaí (ESEFJ were evaluated in an observacional study. The exclusion criteria were: media opacity and eyeball absence or changes. All subjects agreed to take part in this research and signed up the Informed Consent. IOP was measured by Perkins tonometer: i pretest: just before the submaximal strength test performance and ii post-test: immediately after the strength test. The strength test consisted in the one-repetition-maximum-assessment through repetition until fatigue. Resistance training exercises such as bench press, pulley dorsal high, shoulder press, arm curl and leg press 45º were performed

  8. Android Fully Loaded

    CERN Document Server

    Huddleston, Rob

    2012-01-01

    Fully loaded with the latest tricks and tips on your new Android! Android smartphones are so hot, they're soaring past iPhones on the sales charts. And the second edition of this muscular little book is equally impressive--it's packed with tips and tricks for getting the very most out of your latest-generation Android device. Start Facebooking and tweeting with your Android mobile, scan barcodes to get pricing and product reviews, download your favorite TV shows--the book is positively bursting with practical and fun how-tos. Topics run the gamut from using speech recognition, location-based m

  9. Variable loading roller

    Science.gov (United States)

    Williams, Daniel M.

    1989-01-01

    An automatic loading roller for transmitting torque in traction drive devices in manipulator arm joints includes a two-part camming device having a first cam portion rotatable in place on a shaft by an input torque and a second cam portion coaxially rotatable and translatable having a rotating drive surface thereon for engaging the driven surface of an output roller with a resultant force proportional to the torque transmitted. Complementary helical grooves on the respective cam portions interconnected through ball bearings interacting with those grooves effect the rotation and translation of the second cam portion in response to rotation of the first.

  10. Laterally Loaded Nail-Plates

    DEFF Research Database (Denmark)

    Nielsen, Jacob; Rathkjen, Arne

    Load-displacement curves from about 200 short-term and laterally loaded nail-plate joints are analysed. The nail-plates are from Gang-Nail Systems, type GNA 20 S. The test specimens and the measuring systems are described. The tests are divided into 32 different series. The influence of the number...... of nail row, edge distance, fixed nail-plate, bending direction, unloading, and grain direction, plate and load direction on the load-displacement curves are analysed. Mean load-displacement curves from all the tests are given....

  11. Load Control System Reliability

    Energy Technology Data Exchange (ETDEWEB)

    Trudnowski, Daniel [Montana Tech of the Univ. of Montana, Butte, MT (United States)

    2015-04-03

    This report summarizes the results of the Load Control System Reliability project (DOE Award DE-FC26-06NT42750). The original grant was awarded to Montana Tech April 2006. Follow-on DOE awards and expansions to the project scope occurred August 2007, January 2009, April 2011, and April 2013. In addition to the DOE monies, the project also consisted of matching funds from the states of Montana and Wyoming. Project participants included Montana Tech; the University of Wyoming; Montana State University; NorthWestern Energy, Inc., and MSE. Research focused on two areas: real-time power-system load control methodologies; and, power-system measurement-based stability-assessment operation and control tools. The majority of effort was focused on area 2. Results from the research includes: development of fundamental power-system dynamic concepts, control schemes, and signal-processing algorithms; many papers (including two prize papers) in leading journals and conferences and leadership of IEEE activities; one patent; participation in major actual-system testing in the western North American power system; prototype power-system operation and control software installed and tested at three major North American control centers; and, the incubation of a new commercial-grade operation and control software tool. Work under this grant certainly supported the DOE-OE goals in the area of “Real Time Grid Reliability Management.”

  12. Monitoring Training Loads in Professional Basketball Players Engaged in a Periodized Training Program.

    Science.gov (United States)

    Aoki, Marcelo S; Ronda, Lorena T; Marcelino, Pablo R; Drago, Gustavo; Carling, Chris; Bradley, Paul S; Moreira, Alexandre

    2017-02-01

    Aoki, MS, Ronda, LT, Marcelino, PR, Drago, G, Carling, C, Bradley, PS, and Moreira, A. Monitoring training loads in professional basketball players engaged in a periodized training program. J Strength Cond Res 31(2): 348-358, 2017-The aim of this study was to investigate the dynamics of external training load (eTL) and internal training load (iTL) during seasonal periods, and examine the effect of a periodized training program on physical performance in professional basketball players. Repeated measures for 9 players (28 ± 6 years; 199 ± 8 cm; 101 ± 12 kg) were collected from 45 training sessions, over a 6-week preseason phase and a 5-week in-season phase. Physical tests were conducted at baseline (T1), week 4 (T2), and week 9 (T3). Differences in means are presented as % ± confident limits. A very likely difference was observed during in-season compared with preseason for the eTL variables (measured by multivariable monitoring device), mechanical load (13.5 ± 8.8) and peak acceleration (11.0 ± 11.2), respectively. Regarding iTL responses, a very large decrement in TRIMP (most likely difference, -20.6 ± 3.8) and in session rating of perceived exertion training load (very likely difference, -14.2 ± 9.0) was detected from preseason to in-season. Physical performance improved from T1 to T3 for Yo-Yo intermittent recovery test 1 (62.2 ± 34.3, effect size [ES] > 1.2); countermovement jump (8.8 ± 6.1, ES > 0.6); and squat jump (14.8 ± 10.2, ES > 0.8). Heart rate (HR; %HRpeak) exercise responses during a submaximal running test decreased from T1 to T3 (3.2 ± 4.3, ES 1.2). These results provide valuable information to coaches about training loads and physical performance across different seasonal periods. The data demonstrate that both eTL and iTL measures should be monitored in association with physical tests, to provide a comprehensive understanding of the training process.

  13. Use of loaded conditioning activities to potentiate middle- and long-distance performance: a narrative review and practical applications.

    Science.gov (United States)

    Blagrove, Richard C; Howatson, Glyn; Hayes, Philip R

    2018-01-29

    The warm-up is an integral component of a middle- and long-distance athlete's pre-performance routine. The use of a loaded conditioning activity (LCA), which elicits a post-activation potentiation (PAP) response to acutely enhance explosive power performance, is well-researched. A similar approach incorporated into the warm-up of a middle- or long-distance athlete potentially provides a novel strategy to augment performance. Mechanisms that underpin a PAP response, relating to acute adjustments within the neuromuscular system, should theoretically improve middle- and long-distance performance via improvements in sub-maximal force-generating ability. Attempts to enhance middle- and long-distance related outcomes using a LCA have been used in several recent studies. Results suggest benefits to performance may exist in well-trained middle- and long-distance athletes by including high-intensity resistance training (1-5 repetition maximum) or adding load to the sport skill itself during the latter part of warm-ups. Early stages of performance appear to benefit most, and it is likely that recovery (5-10 min) also plays an important role following a LCA. Future research should consider how priming activity, designed to enhance the V[Combining Dot Above]O2 kinetic response, and a LCA may interact to affect performance, and how different LCA's might benefit various modes and durations of middle- and long-distance exercise.

  14. Estimating constituent loads

    Science.gov (United States)

    Cohn, T.A.; DeLong, L.L.; Gilroy, E.J.; Hirsch, R.M.; Wells, D.K.

    1989-01-01

    This paper compares the bias and variance of three procedures that can be used with log linear regression models: the traditional rating curve estimator, a modified rating curve method, and a minimum variance unbiased estimator (MVUE). Analytical derivations of the bias and efficiency of all three estimators are presented. It is shown that for many conditions the traditional and the modified estimator can provide satisfactory estimates. However, other conditions exist where they have substantial bias and a large mean square error. These conditions commonly occur when sample sizes are small, or when loads are estimated during high-flow conditions. The MVUE, however, is unbiased and always performs nearly as well or better than the rating curve estimator or the modified estimator provided that the hypothesis of the log linear model is correct. Since an efficient unbiased estimator is available, there seems to be no reason to employ biased estimators. -from Authors

  15. The impact of work configuration, target angle and hand force direction on upper extremity muscle activity during sub-maximal overhead work.

    Science.gov (United States)

    Chopp, Jaclyn N; Fischer, Steven L; Dickerson, Clark R

    2010-01-01

    Overhead work has established links to upper extremity discomfort and disorders. As many jobs incorporate working overhead, this study aimed to identify working conditions requiring relatively lower muscular shoulder load. Eleven upper extremity muscles were monitored with electromyography during laboratory simulations of overhead work tasks. Tasks were defined with three criteria: work configuration (fixed, stature-specific); target angle (-15 degrees , 0 degrees , 15 degrees , 30 degrees from vertical); direction of applied hand force (pulling backwards, pushing forwards, downwards, sideways, upwards). Normalised electromyographic activity was greater for fixed configurations, particularly when pulling in a backward direction (total activity = 108.3% maximum voluntary exertion (MVE)) compared to pushing down or forward (total activity ranging from 10.5 to 17.3%MVE). Further, pulling backwards at angles of -15 degrees and 0 degrees showed the highest muscular demand (p < 0.05). These results suggest that, if possible, positioning overhead work in front of the body with exertions directed forwards will result in the lowest upper extremity muscle demand. STATEMENT OF RELEVANCE: Overhead work pervades occupational settings and is associated with risk of upper extremity musculoskeletal disorders. The muscular intensity associated with performing overhead work was assessed in several combinations of work placement and hand force direction. These findings should have utility for designing overhead work tasks that reduce muscular exposure.

  16. Effects of reducing exposure to air pollution on submaximal cardiopulmonary test in patients with heart failure: Analysis of the randomized, double-blind and controlled FILTER-HF trial.

    Science.gov (United States)

    Vieira, Jefferson L; Guimaraes, Guilherme V; de Andre, Paulo A; Saldiva, Paulo H Nascimento; Bocchi, Edimar A

    2016-07-15

    Air pollution exposure could mitigate the health benefits of exercise in patients with heart failure (HF). We tested the effects of a respiratory filter on HF patients exposed to air pollution during exercise. Ancillary analysis of the FILTER-HF trial, focused on the exercise outcomes. In a randomized, double-blind, 3-way crossover design, 26 HF patients and 15 control volunteers were exposed to clean air, unfiltered dilute diesel engine exhaust (DE), or filtered DE for 6min during a submaximal cardiopulmonary testing in a controlled-exposure facility. Prospectively collected data included six-minute walking test [6mwt], VO2, VE/VCO2 Slope, O2Pulse, pulmonary ventilation [VE], tidal volume, VD/Vt, oxyhemoglobin saturation and CO2-rebreathing. Compared to clean air, DE adversely affected VO2 (11.0±3.9 vs. 8.4±2.8ml/kg/min; peffects of pollution on VO2 and O2Pulse. Given the worldwide prevalence of exposure to traffic-related air pollution, these findings are relevant for public health especially in this highly susceptible population. The filter intervention holds great promise that needs to be tested in future studies. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  17. Load forecasting for supermarket refrigeration

    DEFF Research Database (Denmark)

    Bacher, Peder; Madsen, Henrik; Aalborg Nielsen, Henrik

    This report presents a study of models for forecasting the load for supermarket refrigeration. The data used for building the forecasting models consists of load measurements, local climate measurements and weather forecasts. The load measurements are from a supermarket located in a village...... in Denmark. The load for refrigeration is the sum of all cabinets in the supermarket, both low and medium temperature cabinets, and spans a period of one year. As input to the forecasting models the ambient temperature observed near the supermarket together with weather forecasts are used. Every hour...... the hourly load for refrigeration for the following 42 hours is forecasted. The forecast models are adaptive linear time-series models which are fitted with a computationally efficient recursive least squares scheme. The dynamic relations between the inputs and the load is modeled by simple transfer...

  18. Load forecasting of supermarket refrigeration

    DEFF Research Database (Denmark)

    Rasmussen, Lisa Buth; Bacher, Peder; Madsen, Henrik

    2016-01-01

    This paper presents a novel study of models for forecasting the electrical load for supermarket refrigeration. The data used for building the models consists of load measurements, local climate measurements and weather forecasts. The load measurements are from a supermarket located in a village...... in Denmark. Every hour the hourly electrical load for refrigeration is forecasted for the following 42 h. The forecast models are adaptive linear time series models. The model has two regimes; one for opening hours and one for closing hours, this is modeled by a regime switching model and two different...

  19. Alaska Village Electric Load Calculator

    Energy Technology Data Exchange (ETDEWEB)

    Devine, M.; Baring-Gould, E. I.

    2004-10-01

    As part of designing a village electric power system, the present and future electric loads must be defined, including both seasonal and daily usage patterns. However, in many cases, detailed electric load information is not readily available. NREL developed the Alaska Village Electric Load Calculator to help estimate the electricity requirements in a village given basic information about the types of facilities located within the community. The purpose of this report is to explain how the load calculator was developed and to provide instructions on its use so that organizations can then use this model to calculate expected electrical energy usage.

  20. Metamaterial Loadings for Waveguide Miniaturization

    CERN Document Server

    Odabasi, H

    2013-01-01

    We show that a rectangular metallic waveguide loaded with metamaterial elements consisting of electric-field coupled (ELC) resonators placed at the side walls can operate well below the cutoff frequency of the respective unloaded waveguide. The dispersion diagrams indicate that propagating modes in ELC-loaded waveguides are of forward-type for both TE and TM modes. We also study the dispersion diagram and transmission characteristics of rectangular metallic waveguides simultaneously loaded with ELCs and split ring resonators (SRRs). Such doubly-loaded waveguides can support both forward wave and backward waves, and provide independent control of the propagation characteristics for the respective modes.

  1. electrical load survey electrical load survey and forecast

    African Journals Online (AJOL)

    eobe

    paper reports the results of electrical load demand and forecast for Elebu rural community located in Kwara State,. Nigeria. The expected peak ... Keywords: hybrid system, renewable energy, optimization, electrical energy, load survey and forecasts. 1. ..... vehicle renewable energy, Monaco, March 26-29,. 2009, pp. 1-9.

  2. Crane-Load Contact Sensor

    Science.gov (United States)

    Youngquist, Robert; Mata, Carlos; Cox, Robert

    2005-01-01

    An electronic instrument has been developed as a prototype of a portable crane-load contact sensor. Such a sensor could be helpful in an application in which the load rests on a base in a horizontal position determined by vertical alignment pins (see Figure 1). If the crane is not positioned to lift the load precisely vertically, then the load can be expected to swing once it has been lifted clear of the pins. If the load is especially heavy, large, and/or fragile, it could hurt workers and/or damage itself and nearby objects. By indicating whether the load remains in contact with the pins when it has been lifted a fraction of the length of the pins, the crane-load contact sensor helps the crane operator determine whether it is safe to lift the load clear of the pins: If there is contact, then the load is resting against the sides of the pins and, hence, it may not be safe to lift; if contact is occasionally broken, then the load is probably not resting against the pins, so it should be safe to lift. It is assumed that the load and base, or at least the pins and the surfaces of the alignment holes in the load, are electrically conductive, so the instrument can use electrical contact to indicate mechanical contact. However, DC resistance cannot be used as an indicator of contact for the following reasons: The load and the base are both electrically grounded through cables (the load is grounded through the lifting cable of the crane) to prevent discharge of static electricity. In other words, the DC resistance between the load and the pins is always low, as though they were always in direct contact. Therefore, instead of DC resistance, the instrument utilizes the AC electrical impedance between the pins and the load. The signal frequency used in the measurement is high enough (.1 MHz) that the impedance contributed by the cables and the electrical ground network of the building in which the crane and the base are situated is significantly greater than the contact

  3. Probabilistic Load Models for Simulating the Impact of Load Management

    DEFF Research Database (Denmark)

    Chen, Peiyuan; Bak-Jensen, Birgitte; Chen, Zhe

    2009-01-01

    to simulate the impact of load management. The joint-normal model is superior in modeling the tail region of the hourly load distribution and implementing the change of hourly standard deviation. Whereas the AR(12) model requires much less parameter and is superior in modeling the autocorrelation......This paper analyzes a distribution system load time series through autocorrelation coefficient, power spectral density, probabilistic distribution and quantile value. Two probabilistic load models, i.e. the joint-normal model and the autoregressive model of order 12 (AR(12)), are proposed....... It is concluded that the AR(12) model is favored with limited measurement data and that the joint-normal model may provide better results with a large data set. Both models can be applied in general to model load time series and used in time-sequential simulation of distribution system planning....

  4. Fatigue Reliability under Random Loads

    DEFF Research Database (Denmark)

    Talreja, R.

    1979-01-01

    We consider the problem of estimating the probability of survival (non-failure) and the probability of safe operation (strength greater than a limiting value) of structures subjected to random loads. These probabilities are formulated in terms of the probability distributions of the loads and the...... propagation stage. The consequences of this behaviour on the fatigue reliability are discussed....

  5. Loading Conditions and Longitudinal Strength

    DEFF Research Database (Denmark)

    Sørensen, Herman

    1995-01-01

    Methods for the calculation of the lightweight of the ship.Loading conditions satisfying draught, trim and intact stability requirements and analysis of the corresponding stillwater longitudinal strength.......Methods for the calculation of the lightweight of the ship.Loading conditions satisfying draught, trim and intact stability requirements and analysis of the corresponding stillwater longitudinal strength....

  6. Load forecasting of supermarket refrigeration

    DEFF Research Database (Denmark)

    Rasmussen, Lisa Buth; Bacher, Peder; Madsen, Henrik

    2016-01-01

    This paper presents a novel study of models for forecasting the electrical load for supermarket refrigeration. The data used for building the models consists of load measurements, local climate measurements and weather forecasts. The load measurements are from a supermarket located in a village...... in Denmark. Every hour the hourly electrical load for refrigeration is forecasted for the following 42 h. The forecast models are adaptive linear time series models. The model has two regimes; one for opening hours and one for closing hours, this is modeled by a regime switching model and two different...... methods for predicting the regimes are tested. The dynamic relation between the weather and the load is modeled by simple transfer functions and the non-linearities are described using spline functions. The results are thoroughly evaluated and it is shown that the spline functions are suitable...

  7. The Location of Peak Upper Trapezius Muscle Activity During Submaximal Contractions is not Associated With the Location of Myofascial Trigger Points: New Insights Revealed by High-density Surface EMG.

    Science.gov (United States)

    Barbero, Marco; Falla, Deborah; Mafodda, Luca; Cescon, Corrado; Gatti, Roberto

    2016-12-01

    To apply topographical mapping of the electromyography (EMG) amplitude recorded from the upper trapezius muscle to evaluate the distribution of activity and the location of peak activity during a shoulder elevation task in participants with and without myofascial pain and myofascial trigger points (MTrP) and compare this location with the site of the MTrP. Thirteen participants with myofascial pain and MTrP in the upper trapezius muscle and 12 asymptomatic individuals participated. High-density surface EMG was recorded from the upper trapezius muscle using a matrix of 64 surface electrodes aligned with an anatomic landmark system (ALS). Each participant performed a shoulder elevation task consisting of a series of 30 s ramped contractions to 15% or 60% of their maximal voluntary contraction (MVC) force. Topographical maps of the EMG average rectified value were computed and the peak EMG amplitude during the ramped contractions was identified and its location determined with respect to the ALS. The location of the MTrP was also determined relative to the ALS and Spearman correlation coefficients were used to examine the relationship between MTrP and peak EMG amplitude location. The location of the peak EMG amplitude was significantly (PEMG amplitude during the ramped contractions at either force level (15%: rs=0.039, P=0.9; 60%: rs=-0.087, P=0.778). People with myofascial pain and MTrP displayed a caudal shift of the distribution of upper trapezius muscle activity compared with asymptomatic individuals during a submaximal shoulder elevation task. For the first time, we show that the location of peak muscle activity is not associated with the location of the MTrP.

  8. The effect of short-duration sub-maximal cycling on balance in single-limb stance in patients with anterior cruciate ligament injury: a cross-sectional study

    Directory of Open Access Journals (Sweden)

    Roberts David

    2004-11-01

    Full Text Available Abstract Background It has previously been shown that an anterior cruciate ligament (ACL injury may lead to impaired postural control, and that the ability to maintain postural control is decreased by fatigue in healthy subjects. To our knowledge, no studies have reported the effect of fatigue on postural control in subjects with ACL injury. This study was aimed at examining the effect of fatigue on balance in single-limb stance in subjects with ACL injury, and to compare the effects, and the ability to maintain balance, with that of a control group of uninjured subjects. Methods Thirty-six patients with unilateral, non-operated, non-acute ACL injury, and 24 uninjured subjects were examined with stabilometry before (pre-exercise and immediately after (post-exercise short-duration, sub-maximal cycling. In addition, the post-exercise measurements were compared, to evaluate the instantaneous ability to maintain balance and any possible recovery. The amplitude and average speed of center of pressure movements were registered in the frontal and sagittal planes. The paired t-test was used for the intra-group comparisons, and the independent t-test for the inter-group comparisons, with Bonferroni correction for multiple comparisons. Results No differences were found in the effects of exercise between the patients and the controls. Analysis of the post-exercise measurements revealed greater effects or a tendency towards greater effects on the injured leg than in the control group. The average speed was lower among the patients than in the control group. Conclusions The results of the present study showed no differences in the effects of exercise between the patients and the controls. However, the patients seemed to react differently regarding ability to maintain balance in single-limb stance directly after exercise than the control group. The lower average speed among the patients may be an expression of different neuromuscular adaptive strategies than

  9. Hydrodynamic loading of tensegrity structures

    Science.gov (United States)

    Wroldsen, Anders S.; Johansen, Vegar; Skelton, Robert E.; Sørensen, Asgeir J.

    2006-03-01

    This paper introduces hydrodynamic loads for tensegrity structures, to examine their behavior in marine environments. Wave compliant structures are of general interest when considering large marine structures, and we are motivated by the aquaculture industry where new concepts are investigated in order to make offshore installations for seafood production. This paper adds to the existing models and software simulations of tensegrity structures exposed to environmental loading from waves and current. A number of simulations are run to show behavior of the structure as a function of pretension level and string stiffness for a given loading condition.

  10. 14 CFR 23.301 - Loads.

    Science.gov (United States)

    2010-01-01

    ... load would significantly change the distribution of external or internal loads, this redistribution...) and ultimate loads (limit loads multiplied by prescribed factors of safety). Unless otherwise provided... validated by flight test measurement unless the methods used for determining those loading conditions are...

  11. Structural Impact of Construction Loads

    Science.gov (United States)

    2012-08-01

    Numerous bridge construction accidents have occurred across the country because of construction loadings, which are an underemphasized : topic in many DOT specifications and design manuals. Bridge girders are least stable when they are subjected to c...

  12. Training load quantification in triathlon

    OpenAIRE

    Cejuela Anta, Roberto; Esteve-Lanao, Jonathan

    2011-01-01

    There are different Indices of Training Stress of varying complexity, to quantification Training load. Examples include the training impulse (TRIMP), the session (RPE), Lucia’s TRIMP or Summated Zone Score. But the triathlon, a sport to be combined where there are interactions between different segments, is a complication when it comes to quantify the training. The aim of this paper is to review current methods of quantification, and to propose a scale to quantify the training load in triathl...

  13. Wind Structure and Wind Loading

    DEFF Research Database (Denmark)

    Brorsen, Michael

    The purpose of this note is to provide a short description of wind, i.e. of the flow in the atmosphere of the Earth and the loading caused by wind on structures. The description comprises: causes to the generation of windhe interaction between wind and the surface of the Earthhe stochastic nature...... of windhe interaction between wind and structures, where it is shown that wind loading depends strongly on this interaction...

  14. Aircraft ditching loads simulation tool

    OpenAIRE

    Bonanni, A.; Vandewaeter, L.; Havill, C.; Kanyoo, P.; Taunton, D.J.; Blake, J.I.R.; Cropper, E.; Hancock, S.

    2015-01-01

    The present work presents a novel methodology developed for calculating the steady loads acting on aircraft structures in the event of ditching in water. It represents the preliminary result of Stirling Dynamics as part of a NATEP research project. The overall objective of the project is to expand the capabilities of the Stirling Dynamics proprietary software SD-GLOAD (originally designed for ground and crash loads dynamic simulations) to aircraft ditching simulations. The methodology present...

  15. Load Estimation from Natural input Modal Analysis

    OpenAIRE

    Aenlle, Manuel López; Brincker, Rune; Canteli, Alfonso Fernández

    2005-01-01

    One application of Natural Input Modal Analysis consists in estimating the unknown load acting on structures such as wind loads, wave loads, traffic loads, etc. In this paper, a procedure to determine loading from a truncated modal model, as well as the results of an experimental testing programme, are presented. The method involves the inversion of the FRF matrix partly solving the numerical problems that appear because of the truncation of the modal space. However, the error in the load est...

  16. Calibration set up for load cells

    Science.gov (United States)

    Rao, T. V. Govinda; Venkatesh, C. S.; Shivashankar, N.

    1989-05-01

    The planning, designing, fabrication, and calibration of 30, 50, and 100 ton tension load cells and 30 ton shear load cells are described. The tension load cells are for monitoring the force developed by earth moving vehicles and the shear load cells are for monitoring the load that tipplers unload form platform to ground. The shear load cells were incorporated into a rotary wagon tippler.

  17. Self-aligning biaxial load frame

    Science.gov (United States)

    Ward, M.B.; Epstein, J.S.; Lloyd, W.R.

    1994-01-18

    An self-aligning biaxial loading apparatus for use in testing the strength of specimens while maintaining a constant specimen centroid during the loading operation. The self-aligning biaxial loading apparatus consists of a load frame and two load assemblies for imparting two independent perpendicular forces upon a test specimen. The constant test specimen centroid is maintained by providing elements for linear motion of the load frame relative to a fixed cross head, and by alignment and linear motion elements of one load assembly relative to the load frame. 3 figures.

  18. A gravity loading countermeasure skinsuit

    Science.gov (United States)

    Waldie, James M.; Newman, Dava J.

    2011-04-01

    Despite the use of several countermeasures, significant physiological deconditioning still occurs during long duration spaceflight. Bone loss - primarily due to the absence of loading in microgravity - is perhaps the greatest challenge to resolve. This paper describes a conceptual Gravity Loading Countermeasure Skinsuit (GLCS) that induces loading on the body to mimic standing and - when integrated with other countermeasures - exercising on Earth. Comfort, mobility and other operational issues were explored during a pilot study carried out in parabolic flight for prototype suits worn by three subjects. Compared to the 1- or 2-stage Russian Pingvin Suits, the elastic mesh of the GLCS can create a loading regime that gradually increases in hundreds of stages from the shoulders to the feet, thereby reproducing the weight-bearing regime normally imparted by gravity with much higher resolution. Modelling shows that the skinsuit requires less than 10 mmHg (1.3 kPa) of compression for three subjects of varied gender, height and mass. Negligible mobility restriction and excellent comfort properties were found during the parabolic flights, which suggests that crewmembers should be able to work normally, exercise or sleep while wearing the suit. The suit may also serve as a practical 1 g harness for exercise countermeasures and vibration applications to improve dynamic loading.

  19. Mental load: helping clinical learners.

    Science.gov (United States)

    White, Geoff

    2011-09-01

    The quality of an individual's learning is influenced significantly by the quantity of mental processing they are required to manage in a clinical learning situation. Some clinical learning settings require the learner to process high levels of complex knowledge and skills, whilst simultaneously monitoring and responding to challenging social or emotional inputs. This paper introduces the concept of 'cognitive load', its negative impacts upon novice learners in particular, and its real-world implications for teaching and supervision. Narrative review and discussion. The concept of cognitive load is reviewed, and examples of its application to clinical learning and teaching are provided. Teaching and supervision strategies for managing the cognitive load of learners are presented. The clinical teacher has significant capacity to reduce the cognitive load of learners by creating safe and supportive learning environments, establishing trusting relationships with the learner, and implementing structured learning experiences that are designed to support the learner's growth in knowledge, understanding and skills. A threefold focus on the nature of the learning task, the learning environment and the learner's perceptions of these elements, which characterises cognitive load, provides a useful framework for diagnosing poor learning behaviours and maximising learning outcomes. © Blackwell Publishing Ltd 2011.

  20. Ultimate loading of wind turbines

    DEFF Research Database (Denmark)

    Larsen, Gunner Chr.; Ronold, K.; Ejsing Jørgensen, Hans

    1999-01-01

    to establish partial safety factors for design of such components against this failure mode, structuralreliability methods must be applied. This type of analysis accounts for the variability of the external (wind) loading (as addressed in the analyses of the general wind climate) - and thereby the induced......An extreme loading study has been conducted comprising a general wind climate analysis as well as a wind turbine reliability study. In the wind climate analysis, the distribution of the (horizontal) turbulence standard deviation, conditioned on the meanwind speed, has been approximated by fitting......, a design turbulence intensity for off-shore application is proposed which, in the IEC code framework, is applicable for extreme as well as for fatigue loaddetermination. In order to establish a rational method to analyse wind turbine components with respect to failure in ultimate loading, and in addition...

  1. Effect of music on submaximal cycling

    African Journals Online (AJOL)

    Boutcher SH, Trenske M. The effects of sensory deprivation and music on perceived exertion and affect during exercise. Journal of Sport and Exercise. Psychology 1990; 12: 167-76. 4. Grant S, Aitchison T, Henderson E, et al. A comparison of the reproduc- ibility and the sensitivity to change of visual analogue scales, Borg ...

  2. Load flow analysis using decoupled fuzzy load flow under critical ...

    African Journals Online (AJOL)

    user

    mismatch and summation of power mismatches are taken as two inputs for fuzzy logic controller. Considering magnitude of power mismatch and sign of power mismatch, new 25 fuzzy rules are created from two sets of inputs. The proposed Decoupled. Fuzzy Load Flow (FDLF) is applied to IEEE 14 bus, IEEE 30 bus, IEEE ...

  3. RF Loads for Energy Recovery

    CERN Document Server

    Federmann, S; Caspers, F

    2012-01-01

    Different conceptional designs for RF high power loads are presented. One concept implies the use of solid state rectifier modules for direct RF to DC conversion with efficiencies beyond 80%. In addition, robust metallic low-Q resonant structures, capable of operating at high temperatures (>150 ◦C) are discussed. Another design deals with a very high temperature (up to 800 ◦C) air cooled load using a ceramic foam block inside a metal enclosure. This porous ceramic block is the microwave absorber and is not brazed to the metallic enclosure.

  4. Load Estimation by Frequency Domain Decomposition

    DEFF Research Database (Denmark)

    Pedersen, Ivar Chr. Bjerg; Hansen, Søren Mosegaard; Brincker, Rune

    2007-01-01

    When performing operational modal analysis the dynamic loading is unknown, however, once the modal properties of the structure have been estimated, the transfer matrix can be obtained, and the loading can be estimated by inverse filtering. In this paper loads in frequency domain are estimated...... and the errors on the estimated loads are determined....

  5. 14 CFR 27.865 - External loads.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false External loads. 27.865 Section 27.865... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction External Loads § 27.865 External loads. (a) It must be shown by analysis, test, or both, that the rotorcraft external load attaching means for...

  6. 14 CFR 29.865 - External loads.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false External loads. 29.865 Section 29.865... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction External Loads § 29.865 External loads. (a) It must be shown by analysis, test, or both, that the rotorcraft external load attaching means for...

  7. Analyses of tunnel stability under dynamic loads

    OpenAIRE

    Oraee, B; Hosseini, N.; Oraee, K; Gholinejad, M

    2011-01-01

    Tunnels as any other structures are affected by different loads and stresses. Generally, the loads on tunnels consist of both static and dynamic loads. These loads must both be considered in the tunnel design process. In this paper, the stability state of Jiroft water-transform tunnel is evaluated. Firstly, the in-situ stresses and then using Kirschs equations the induced stresses due to static loads in walls and crown of tunnel are calculated. Consequently, the strain caused by probable eart...

  8. Numerical prediction of slamming loads

    DEFF Research Database (Denmark)

    Seng, Sopheak; Jensen, Jørgen J; Pedersen, Preben T

    2012-01-01

    It is important to include the contribution of the slamming-induced response in the structural design of large vessels with a significant bow flare. At the same time it is a challenge to develop rational tools to determine the slamming-induced loads and the prediction of their occurrence. Today i...

  9. Resource augmentation in load balancing

    NARCIS (Netherlands)

    Y. Azar; L. Epstein (Lea); R. van Stee (Rob)

    1999-01-01

    textabstractWe consider load-balancing in the following setting. The on-line algorithm is allowed to use $n$ machines, whereas the optimal off-line algorithm is limited to $m$ machines, for some fixed $m < n$. We show that while the greedy algorithm has a competitive ratio which decays linearly in

  10. Soil Profiles and Seismic Loading

    Directory of Open Access Journals (Sweden)

    Janotka, V.

    2006-01-01

    Full Text Available The contribution estimates different geotechnical profiles of site condition change and their influences on the computed seismic response spectra and time histories final values and forms applying on the seismic structures loading. The mentioned problems methodics attitude solution is based on the computed seismic motion parameters.

  11. Fracture load of ceramic restorations after fatigue loading.

    Science.gov (United States)

    Baladhandayutham, Balasudha; Lawson, Nathaniel C; Burgess, John O

    2015-08-01

    A clinician must decide what ceramic coping and veneer material to prescribe based on the amount of tooth reduction possible and the desired esthetic outcome of the restoration. The purpose of this in vitro study was to compare the fracture strength of monolithic and bilayered lithium disilicate (IPS e.max) and zirconia (LAVA) crowns at clinically relevant thicknesses after load cycling. Crowns (n=8) were fabricated from 6 groups: 1.2-mm monolithic lithium disilicate, 1.5-mm monolithic lithium disilicate, 1.5-mm bilayered lithium disilicate with hand-layered veneer, 0.6 mm monolithic zirconia, 1.2-mm bilayered zirconia with hand-layered veneer, and 1.2-mm bilayered zirconia with milled veneer (dimension represents thickness at the occlusal pit). Crowns were cemented to identical milled resin dies with resin-modified glass ionomer cement. Cemented crowns were stored at 37°C for 24 hours and load cycled for 200,000 cycles at 25 N at a rate of 40 cycles/minute. The ultimate fracture load for each specimen was measured in a universal testing machine. Data were analyzed with a 1-way ANOVA and Tukey honest significant difference post hoc analysis (α=.05). Mean ±SD fracture load values were 1465 ±330 N for monolithic lithium disilicate (1.2-mm thickness) and 2027 ±365 N (1.5-mm thickness) and 1732 ±315 N for bilayered hand-veneered lithium disilicate (1.5-mm thickness). Fracture loads were 1669 ±311 N for monolithic zirconia crowns (0.6mm thickness), 2625 ±300 N for zirconia milled-veneered (1.2-mm thickness), and 2655 ±590N for zirconia hand-veneered crowns (1.2mm thickness). One-way ANOVA showed a statistically significant difference among the groups (PVeneered zirconia crowns showed the highest fracture strength, 1.2-mm hand veneered zirconia was similar to that of 1.5-mm monolithic zirconia, and all other groups were not statistically different. Crowns of 1.2-mm bilayered zirconia had higher fracture loads than 0.6-mm zirconia or 1.2-mm lithium disilicate

  12. Experimental investigation of ultimate loads

    Energy Technology Data Exchange (ETDEWEB)

    Petersen, S.M.; Larsen, G.C.; Antoniou, I.; Lind, S.O.; Courtney, M. [Risoe National Lab., Wind Energy and Atmospheric Physics, Roskilde (Denmark)

    1999-03-01

    Verification of the structural integrity of a wind turbine involves analysis of fatigue loading as well as ultimate loading. With the trend of persistently growing turbines, the ultimate loading seems to become relatively more important. For wind turbines designed according to the wind conditions prescribed in the IEC-61400 code, the ultimate load is often identified as the leading load parameter. Exemplified by the use of an extensive measurement campaign a procedure for evaluation of the extreme flap-wise bending moments, occurring during normal operating of a wind turbine, is presented. The structural measurements are made on a NEG Micon 650 kW wind turbine erected at a complex high wind site in Oak Creek, California. The turbine is located on the top of a ridge. The prevailing wind direction is perpendicular to the ridge, and the annual mean wind speed is 9.5 m/s. The associated wind field measurement, are taken from two instrumented masts erected less than one rotor diameter in front of the turbine in direction of the prevailing wind direction. Both masts are instrumented at different heights in order to gain insight of the 3D-wind speed structure over the entire rotor plane. Extreme distributions, associated with a recurrence period of 10 minutes, conditioned on the mean wind speed and the turbulence intensity are derived. Combined with the wind climate model proposed in the IEC standard, these distributions are used to predict extreme distributions with recurrence periods equal to one and fifty years, respectively. The synthesis of the conditioned PDF`s and the wind climate model is performed by means of Monte Carlo simulation. (au)

  13. 46 CFR 154.1730 - Ethylene oxide: Loading and off loading.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Ethylene oxide: Loading and off loading. 154.1730... Operating Requirements § 154.1730 Ethylene oxide: Loading and off loading. (a) The master shall ensure that before ethylene oxide is loaded into a cargo tank: (1) The tank is thoroughly clean, dry, and free of...

  14. Load Estimation from Natural input Modal Analysis

    DEFF Research Database (Denmark)

    Aenlle, Manuel López; Brincker, Rune; Canteli, Alfonso Fernández

    2005-01-01

    One application of Natural Input Modal Analysis consists in estimating the unknown load acting on structures such as wind loads, wave loads, traffic loads, etc. In this paper, a procedure to determine loading from a truncated modal model, as well as the results of an experimental testing programme...... estimation. In the experimental program a small structure subjected to vibration was used to estimate the loading from the measurements and the experimental modal space. The modal parameters were estimated by Natural Input Modal Analysis and the scaling factors of the mode shapes obtained by the mass change...

  15. Trailer-loading of horses

    DEFF Research Database (Denmark)

    Hendriksen, Payana; Elmgreen, Katrine; Ladewig, Jan

    2011-01-01

    trailer-loading problems were selected and exposed to trailer-loading. They were randomly assigned to one of the 2 methods. NR consisted of various degrees of pressure (lead rope pulling, whip tapping). Pressure was removed as soon as the horse complied. PR horses were exposed to clicker training......The traditional way to train horses is by the application of negative reinforcement (NR). In the past few years, however, the use of positive reinforcement (PR) has become more common. To evaluate the effectiveness and the possible stressor effect of the 2 training methods, 12 horses showing severe...... and taught to follow a target into the trailer. Heart rate (HR) was recorded every 5 seconds and behavior denoting discomfort was observed using one-zero sampling with 10 seconds sampling intervals. Training was completed when the horse could enter the trailer upon a signal, or was terminated after a maximum...

  16. Efficiency of Capacitively Loaded Converters

    DEFF Research Database (Denmark)

    Andersen, Thomas; Huang, Lina; Andersen, Michael A. E.

    2012-01-01

    This paper explores the characteristic of capacitance versus voltage for dielectric electro active polymer (DEAP) actuator, 2kV polypropylene film capacitor as well as 3kV X7R multi layer ceramic capacitor (MLCC) at the beginning. An energy efficiency for capacitively loaded converters...... is introduced as a definition of efficiency. The calculated and measured efficiency curves for charging DEAP actuator, polypropylene film capacitor and X7R MLCC are provided and compared. The attention has to be paid for the voltage dependent capacitive load, like X7R MLCC, when evaluating the charging...... efficiency of converter. Based on the capacitancevoltage curve, the correct capacitance should be chosen when calculating the stored energy; otherwise misleading optimistic efficiency can always be obtained. Actually, when DEAP actuator is not available at the early developing stage, the voltage independent...

  17. Polymer brushes under high load.

    Directory of Open Access Journals (Sweden)

    Suzanne M Balko

    Full Text Available Polymer coatings are frequently used to provide repulsive forces between surfaces in solution. After 25 years of design and study, a quantitative model to explain and predict repulsion under strong compression is still lacking. Here, we combine experiments, simulations, and theory to study polymer coatings under high loads and demonstrate a validated model for the repulsive forces, proposing that this universal behavior can be predicted from the polymer solution properties.

  18. Fatigue Performance under Multiaxial Loading

    Science.gov (United States)

    1990-01-01

    Fatigue Strength (Study fatigue strength in cor. connect, in box struc.)." Prog. Rpt. 1, Res. Inst. Ishikawajima - Harima Heavy Ind. Co., Ltd., Tokyo, Japan...1," Ishikawajima - Harima Heavy Ind. Co., Ltd. Research Inst., Tokyo, Japan, IIW Doc. No XIII-573-70. Mall, G., and R. Zirn, "Load Carrying Behavior of...1972. Anonymous, "Application of Program Fatigue Test to Member Joints of Hulls," Mitsubishi Heavy Industries LTD, Mitsubishi Technical Bulletin No

  19. Inducer Hydrodynamic Load Measurement Devices

    Science.gov (United States)

    Skelley, Stephen E.; Zoladz, Thomas F.

    2002-01-01

    Marshall Space Flight Center (MSFC) has demonstrated two measurement devices for sensing and resolving the hydrodynamic loads on fluid machinery. The first - a derivative of the six component wind tunnel balance - senses the forces and moments on the rotating device through a weakened shaft section instrumented with a series of strain gauges. This "rotating balance" was designed to directly measure the steady and unsteady hydrodynamic loads on an inducer, thereby defining both the amplitude and frequency content associated with operating in various cavitation modes. The second device - a high frequency response pressure transducer surface mounted on a rotating component - was merely an extension of existing technology for application in water. MSFC has recently completed experimental evaluations of both the rotating balance and surface-mount transducers in a water test loop. The measurement bandwidth of the rotating balance was severely limited by the relative flexibility of the device itself, resulting in an unexpectedly low structural bending mode and invalidating the higher frequency response data. Despite these limitations, measurements confirmed that the integrated loads on the four-bladed inducer respond to both cavitation intensity and cavitation phenomena. Likewise, the surface-mount pressure transducers were subjected to a range of temperatures and flow conditions in a non-rotating environment to record bias shifts and transfer functions between the transducers and a reference device. The pressure transducer static performance was within manufacturer's specifications and dynamic response accurately followed that of the reference.

  20. High Temperature Radio Frequency Loads

    CERN Document Server

    Federmann, S; Grudiev, A; Montesinos, E; Syratchev, I

    2011-01-01

    In the context of energy saving and recovery requirements the design of reliable and robust RF power loads which permit a high outlet temperature and high pressure of the cooling water is desirable. Cooling water arriving at the outlet withmore than 150 ◦C and high pressure has a higher value than water with 50 ◦C under low pressure. Conventional RF power loads containing dielectric and magnetic materials as well as sensitive ceramic windows usually do not permit going much higher than 90 ◦C. Here we present and discuss several design concepts for "metal only" RF high power loads. One concept is the application of magnetic steel corrugated waveguides near cutoff – this concept could find practical use above several GHz. Another solution are resonant structures made of steel to be installed in large waveguides for frequencies of 500 MHz or lower. Similar resonant structures above 100 MHz taking advantage of the rather high losses of normal steel may also be used in coaxial line geometries with large di...

  1. PASSIVE DETECTION OF VEHICLE LOADING

    Energy Technology Data Exchange (ETDEWEB)

    Garrett, A.

    2012-01-03

    The Digital Imaging and Remote Sensing Laboratory (DIRS) at the Rochester Institute of Technology, along with the Savannah River National Laboratory is investigating passive methods to quantify vehicle loading. The research described in this paper investigates multiple vehicle indicators including brake temperature, tire temperature, engine temperature, acceleration and deceleration rates, engine acoustics, suspension response, tire deformation and vibrational response. Our investigation into these variables includes building and implementing a sensing system for data collection as well as multiple full-scale vehicle tests. The sensing system includes; infrared video cameras, triaxial accelerometers, microphones, video cameras and thermocouples. The full scale testing includes both a medium size dump truck and a tractor-trailer truck on closed courses with loads spanning the full range of the vehicle's capacity. Statistical analysis of the collected data is used to determine the effectiveness of each of the indicators for characterizing the weight of a vehicle. The final sensing system will monitor multiple load indicators and combine the results to achieve a more accurate measurement than any of the indicators could provide alone.

  2. Probabilistic Meteorological Characterization for Turbine Loads

    DEFF Research Database (Denmark)

    Kelly, Mark C.; Larsen, Gunner Chr.; Dimitrov, Nikolay Krasimirov

    2014-01-01

    Beyond the existing, limited IEC prescription to describe fatigue loads on wind turbines, we look towards probabilistic characterization of the loads via analogous characterization of the atmospheric flow, particularly for today's "taller" turbines with rotors well above the atmospheric surface...

  3. Acid loading test (pH)

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/003615.htm Acid loading test (pH) To use the sharing features on this page, please enable JavaScript. The acid loading test (pH) measures the ability of the ...

  4. Plug Load Behavioral Change Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    Metzger, I.; Kandt, A.; VanGeet, O.

    2011-08-01

    This report documents the methods and results of a plug load study of the Environmental Protection Agency's Region 8 Headquarters in Denver, Colorado, conducted by the National Renewable Energy Laboratory. The study quantified the effect of mechanical and behavioral change approaches on plug load energy reduction and identified effective ways to reduce plug load energy. Load reduction approaches included automated energy management systems and behavioral change strategies.

  5. Simulation of Stochastic Loads for Fatigue Experiments

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Brincker, Rune

    A simple direct simulation method for stochastic fatigue load generation is described in this paper. The simulation method is based on the assumption that only the peaks of the load process significantly affect the fatigue life. The method requires the conditional distribution functions of load...... second using an IBM PC. Finally the proposed simulation method for fatigue load generation is tested by comparing some fatigue damage measures obtained by the simulation methods....

  6. System and method employing a minimum distance and a load feature database to identify electric load types of different electric loads

    Science.gov (United States)

    Lu, Bin; Yang, Yi; Sharma, Santosh K; Zambare, Prachi; Madane, Mayura A

    2014-12-23

    A method identifies electric load types of a plurality of different electric loads. The method includes providing a load feature database of a plurality of different electric load types, each of the different electric load types including a first load feature vector having at least four different load features; sensing a voltage signal and a current signal for each of the different electric loads; determining a second load feature vector comprising at least four different load features from the sensed voltage signal and the sensed current signal for a corresponding one of the different electric loads; and identifying by a processor one of the different electric load types by determining a minimum distance of the second load feature vector to the first load feature vector of the different electric load types of the load feature database.

  7. Load Bearing Equipment for Bone and Muscle

    Science.gov (United States)

    Shackelford, Linda; Griffith, Bryan

    2015-01-01

    Resistance exercise on ISS has proven effective in maintaining bone mineral density and muscle mass. Exploration missions require exercise with similar high loads using equipment with less mass and volume and greater safety and reliability than resistance exercise equipment used on ISS (iRED, ARED, FWED). Load Bearing Equipment (LBE) uses each exercising person to create and control the load to the partner.

  8. Plutonium Immobilization Can Loading Preliminary Specifications

    Energy Technology Data Exchange (ETDEWEB)

    Kriikku, E.

    1998-11-25

    This report discusses the Plutonium Immobilization can loading preliminary equipment specifications and includes a process block diagram, process description, equipment list, preliminary equipment specifications, plan and elevation sketches, and some commercial catalogs. This report identifies loading pucks into cans and backfilling cans with helium as the top priority can loading development areas.

  9. 10 CFR 434.512 - Internal loads.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 3 2010-01-01 2010-01-01 false Internal loads. 434.512 Section 434.512 Energy DEPARTMENT... RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.512 Internal loads. 512.1The systems... Schedules. Internal loads for other building types shall be modeled as noted in this subsection. Table 512.2...

  10. 49 CFR 195.110 - External loads.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false External loads. 195.110 Section 195.110 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... PIPELINE Design Requirements § 195.110 External loads. (a) Anticipated external loads (e.g.), earthquakes...

  11. Load balancing in integrated optical wireless networks

    DEFF Research Database (Denmark)

    Yan, Ying; Dittmann, Lars; Wong, S-W.

    2010-01-01

    In this paper, we tackle the load balancing problem in Integrated Optical Wireless Networks, where cell breathing technique is used to solve congestion by changing the coverage area of a fully loaded cell tower. Our objective is to design a load balancing mechanism which works closely...

  12. 33 CFR 154.510 - Loading arms.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Loading arms. 154.510 Section 154... FACILITIES TRANSFERRING OIL OR HAZARDOUS MATERIAL IN BULK Equipment Requirements § 154.510 Loading arms. (a) Each mechanical loading arm used for transferring oil or hazardous material and placed into service...

  13. Local Dynamic Stability Associated with Load Carrying

    Directory of Open Access Journals (Sweden)

    Jian Liu

    2013-03-01

    Conclusion: Current study confirmed the sensitivity of local dynamic stability measure in load carrying situation. It was concluded that load carrying tasks were associated with declined local dynamic stability, which may result in increased risk of fall accident. This finding has implications in preventing fall accidents associated with occupational load carrying.

  14. Determining large deflections in rectangular combined loaded ...

    Indian Academy of Sciences (India)

    In this study, large deflection of cantilever beams of Ludwick type material subjected to a combined loading consisting of a uniformly distributed load and one vertical concentrated load at the free end was investigated. In calculations, both material and geometrical non-linearity have been considered. Horizontal and vertical ...

  15. Response of Rubble Foundation to Dynamic Loading

    DEFF Research Database (Denmark)

    Burcharth, H. F.; Ibsen, Lars Bo

    1993-01-01

    The soil beneath vertical monolithic structures is subjected to a combination of static load due to the submerged weight of the structure and stochastic non-stationary loads as a result of the wave loads on the vertical wall. The stress conditions in the soil below a foundation exposed to both...

  16. Determining large deflections in rectangular combined loaded ...

    Indian Academy of Sciences (India)

    Abstract. In this study, large deflection of cantilever beams of Ludwick type material subjected to a combined loading consisting of a uniformly distributed load and one vertical concentrated load at the free end was investigated. In calcula- tions, both material and geometrical non-linearity have been considered. Horizon-.

  17. Timber joints under long-term loading

    DEFF Research Database (Denmark)

    Feldborg, T.; Johansen, M.

    This report describes tests and results from stiffness and strength testing of splice joints under long-term loading. During two years of loading the spicimens were exposed to cyclically changing relative humidity. After the loading period the specimens were short-term tested. The connectors were...

  18. Response of Rubble Foundation to Dynamic Loading

    DEFF Research Database (Denmark)

    Burcharth, H. F.; Ibsen, Lars Bo

    1994-01-01

    The soil beneath vertical monolithic structures is subjected to a combination of static load due to the submerged weight of the structure and stochastic non-stationary loads as a result of the wave loads on the vertical wall. The stress conditions in the soil below a foundation exposed to both st...

  19. Wind loads on solar energy systems

    NARCIS (Netherlands)

    Kampen, B.J.M. van; Geurts, C.P.W.; Borsboom, W.A.; Blackmore, P.

    2005-01-01

    Wind loads on solar energy systems are not covered by current wind loading standards. This paper describes results of a parametric study into the wind loads 0on solar energy systems,. which are placed on flat roofs. Wind tunnel measurements have been carried out on a number of configurations. The

  20. Beam heat load in superconducting wigglers

    CERN Document Server

    Casalbuoni, S.

    2013-04-22

    The beam heat load is a fundamental input parameter for the design of superconducting wigglers since it is needed to specify the cooling power. In this presentation I will review the possible beam heat load sources and the measurements of beam heat load performed and planned onto the cold vacuum chambers installed at different synchrotron light sources.

  1. Soil Behavior Under Blast Loading

    Science.gov (United States)

    2010-12-01

    compressive stress of creep loading causes the pore water pressure to increase. If drainage is possible an outflow of water then takes place into...behavior such as creep and temperature-dependency. Those aspects are not discussed here because they are beyond the scopes in this study. 2.2.2...0.00060 0.0012 0.0020 0.0040 0.0060 $ P9 P10 0.0080 0.041 *MAT_USER_DEFINED_MATERIAL_MODELS $ MID RO

  2. Spatial peak-load pricing

    Energy Technology Data Exchange (ETDEWEB)

    Arellano, M. Soledad; Serra, Pablo [Universidad de Chile, Dept. of Industrial Engineering, Santiago (Chile)

    2007-03-15

    This article extends the traditional electricity peak-load pricing model to include transmission costs. In the context of a two-node, two-technology electric power system, where suppliers face inelastic demand, we show that when the marginal plant is located at the energy-importing center, generators located away from that center should pay the marginal capacity transmission cost; otherwise, consumers should bear this cost through capacity payments. Since electric power transmission is a natural monopoly, marginal-cost pricing does not fully cover costs. We propose distributing the revenue deficit among users in proportion to the surplus they derive from the service priced at marginal cost. (Author)

  3. Critical loads - assessment of uncertainty

    Energy Technology Data Exchange (ETDEWEB)

    Barkman, A.

    1998-10-01

    The effects of data uncertainty in applications of the critical loads concept were investigated on different spatial resolutions in Sweden and northern Czech Republic. Critical loads of acidity (CL) were calculated for Sweden using the biogeochemical model PROFILE. Three methods with different structural complexity were used to estimate the adverse effects of S0{sub 2} concentrations in northern Czech Republic. Data uncertainties in the calculated critical loads/levels and exceedances (EX) were assessed using Monte Carlo simulations. Uncertainties within cumulative distribution functions (CDF) were aggregated by accounting for the overlap between site specific confidence intervals. Aggregation of data uncertainties within CDFs resulted in lower CL and higher EX best estimates in comparison with percentiles represented by individual sites. Data uncertainties were consequently found to advocate larger deposition reductions to achieve non-exceedance based on low critical loads estimates on 150 x 150 km resolution. Input data were found to impair the level of differentiation between geographical units at all investigated resolutions. Aggregation of data uncertainty within CDFs involved more constrained confidence intervals for a given percentile. Differentiation as well as identification of grid cells on 150 x 150 km resolution subjected to EX was generally improved. Calculation of the probability of EX was shown to preserve the possibility to differentiate between geographical units. Re-aggregation of the 95%-ile EX on 50 x 50 km resolution generally increased the confidence interval for each percentile. Significant relationships were found between forest decline and the three methods addressing risks induced by S0{sub 2} concentrations. Modifying S0{sub 2} concentrations by accounting for the length of the vegetation period was found to constitute the most useful trade-off between structural complexity, data availability and effects of data uncertainty. Data

  4. Automated Loads Analysis System (ATLAS)

    Science.gov (United States)

    Gardner, Stephen; Frere, Scot; O’Reilly, Patrick

    2013-01-01

    ATLAS is a generalized solution that can be used for launch vehicles. ATLAS is used to produce modal transient analysis and quasi-static analysis results (i.e., accelerations, displacements, and forces) for the payload math models on a specific Shuttle Transport System (STS) flight using the shuttle math model and associated forcing functions. This innovation solves the problem of coupling of payload math models into a shuttle math model. It performs a transient loads analysis simulating liftoff, landing, and all flight events between liftoff and landing. ATLAS utilizes efficient and numerically stable algorithms available in MSC/NASTRAN.

  5. Online load forecasting for supermarket refrigeration

    DEFF Research Database (Denmark)

    Bacher, Peder; Madsen, Henrik; Nielsen, Henrik Aalborg

    2013-01-01

    This paper presents a study of models for forecasting the load for supermarket refrigeration. The data used for building the forecasting models consists of load measurements, local climate measurements and weather forecasts. The load measurements are from a supermarket located in a village...... in Denmark. Every hour the hourly load for refrigeration for the following 42 hours is forecasted. The forecast models are time adaptive linear time-series models. The dynamic relations between the inputs and the load is modeled by simple transfer functions. The system operates in two regimes: one...

  6. Novel Musculoskeletal Loading and Assessment System

    Science.gov (United States)

    Downs, Meghan E.

    2017-01-01

    Ground based and ISS (International Space Station) exercise research have shown that axial loading via two-point loading at the shoulders and load quality (i.e. consistent load and at least 1:1 concentric to eccentric ratio) are extremely important to optimize musculoskeletal adaptations to resistance exercise. The Advanced Resistance Exercise Device (ARED) is on ISS now and is the "state of the art" for resistance exercise capabilities in microgravity; however, the ARED is far too large and power consuming for exploration vehicles. The single cable exercise device design selected for MPCV (Multi-Purpose Crew Vehicle), does not readily allow for the two-point loading at the shoulders.

  7. Concurrent Working Memory Load Can Facilitate Selective Attention: Evidence for Specialized Load

    Science.gov (United States)

    Park, Soojin; Kim, Min-Shik; Chun, Marvin M.

    2007-01-01

    Load theory predicts that concurrent working memory load impairs selective attention and increases distractor interference (N. Lavie, A. Hirst, J. W. de Fockert, & E. Viding, see record 2004-17825-003). Here, the authors present new evidence that the type of concurrent working memory load determines whether load impairs selective attention or not.…

  8. Effect of loading rate on the fracture behavior of nuclear piping materials under cyclic loading conditions

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jin Weon; Choi, Myung Rak [Dept. of Nuclear Engineering, Chosun University, Gwangju (Korea, Republic of); Kim, Yun Jae [Dept. of Mechanical Engineering, Korea University, Seoul (Korea, Republic of)

    2016-12-15

    This study investigated the loading rate effect on the fracture resistance under cyclic loading conditions to understand clearly the fracture behavior of piping materials under seismic conditions. J-R fracture toughness tests were conducted under monotonic and cyclic loading conditions at various displacement rates at room temperature and the operating temperature of nuclear power plants (i.e., 316°C). SA508 Gr.1a low-alloy steel and SA312 TP316 stainless steel piping materials were used for the tests. The fracture resistance under a reversible cyclic load was considerably lower than that under monotonic load regardless of test temperature, material, and loading rate. Under both cyclic and monotonic loading conditions, the fracture behavior of SA312 TP316 stainless steel was independent of the loading rate at both room temperature and 316°C. For SA508 Gr.1a low-alloy steel, the loading rate effect on the fracture behavior was appreciable at 316°C under cyclic and monotonic loading conditions. However, the loading rate effect diminished when the cyclic load ratio of the load (R) was -1. Thus, it was recognized that the fracture behavior of piping materials, including seismic loading characteristics, can be evaluated when tested under a cyclic load of R = -1 at a quasistatic loading rate.

  9. Effect of Loading Rate on the Fracture Behavior of Nuclear Piping Materials Under Cyclic Loading Conditions

    Directory of Open Access Journals (Sweden)

    Jin Weon Kim

    2016-12-01

    Full Text Available This study investigated the loading rate effect on the fracture resistance under cyclic loading conditions to understand clearly the fracture behavior of piping materials under seismic conditions. J–R fracture toughness tests were conducted under monotonic and cyclic loading conditions at various displacement rates at room temperature and the operating temperature of nuclear power plants (i.e., 316°C. SA508 Gr.1a low-alloy steel and SA312 TP316 stainless steel piping materials were used for the tests. The fracture resistance under a reversible cyclic load was considerably lower than that under monotonic load regardless of test temperature, material, and loading rate. Under both cyclic and monotonic loading conditions, the fracture behavior of SA312 TP316 stainless steel was independent of the loading rate at both room temperature and 316°C. For SA508 Gr.1a low-alloy steel, the loading rate effect on the fracture behavior was appreciable at 316°C under cyclic and monotonic loading conditions. However, the loading rate effect diminished when the cyclic load ratio of the load (R was −1. Thus, it was recognized that the fracture behavior of piping materials, including seismic loading characteristics, can be evaluated when tested under a cyclic load of R = −1 at a quasistatic loading rate.

  10. 14 CFR 23.511 - Ground load; unsymmetrical loads on multiple-wheel units.

    Science.gov (United States)

    2010-01-01

    ... multiple-wheel units. 23.511 Section 23.511 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... CATEGORY AIRPLANES Structure Ground Loads § 23.511 Ground load; unsymmetrical loads on multiple-wheel units... distribution, to the dual wheels and tires in each dual wheel landing gear unit. (c) Deflated tire loads. For...

  11. 14 CFR 25.511 - Ground load: unsymmetrical loads on multiple-wheel units.

    Science.gov (United States)

    2010-01-01

    ... multiple-wheel units. 25.511 Section 25.511 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... Loads § 25.511 Ground load: unsymmetrical loads on multiple-wheel units. (a) General. Multiple-wheel...-wheel unit; and (2) In determining the total load on a gear unit with respect to the provisions of...

  12. Detection of Unexpected High Correlations between Balance Calibration Loads and Load Residuals

    Science.gov (United States)

    Ulbrich, N.; Volden, T.

    2014-01-01

    An algorithm was developed for the assessment of strain-gage balance calibration data that makes it possible to systematically investigate potential sources of unexpected high correlations between calibration load residuals and applied calibration loads. The algorithm investigates correlations on a load series by load series basis. The linear correlation coefficient is used to quantify the correlations. It is computed for all possible pairs of calibration load residuals and applied calibration loads that can be constructed for the given balance calibration data set. An unexpected high correlation between a load residual and a load is detected if three conditions are met: (i) the absolute value of the correlation coefficient of a residual/load pair exceeds 0.95; (ii) the maximum of the absolute values of the residuals of a load series exceeds 0.25 % of the load capacity; (iii) the load component of the load series is intentionally applied. Data from a baseline calibration of a six-component force balance is used to illustrate the application of the detection algorithm to a real-world data set. This analysis also showed that the detection algorithm can identify load alignment errors as long as repeat load series are contained in the balance calibration data set that do not suffer from load alignment problems.

  13. The effects of load and gradient on hand force responses during ...

    African Journals Online (AJOL)

    The limited attention afforded to push/pull activities and the motion phases (initial, sustained and ending) characteristic of these tasks has prompted a research focus in this area. The present study examined biomechanical responses in the form of hand forces during dynamic submaximal trolley pushing and pulling.

  14. Low reflectance radio frequency load

    Science.gov (United States)

    Ives, R. Lawrence; Mizuhara, Yosuke M

    2014-04-01

    A load for traveling microwave energy has an absorptive volume defined by cylindrical body enclosed by a first end cap and a second end cap. The first end cap has an aperture for the passage of an input waveguide with a rotating part that is coupled to a reflective mirror. The inner surfaces of the absorptive volume consist of a resistive material or are coated with a coating which absorbs a fraction of incident RF energy, and the remainder of the RF energy reflects. The angle of the reflector and end caps is selected such that reflected RF energy dissipates an increasing percentage of the remaining RF energy at each reflection, and the reflected RF energy which returns to the rotating mirror is directed to the back surface of the rotating reflector, and is not coupled to the input waveguide. Additionally, the reflector may have a surface which generates a more uniform power distribution function axially and laterally, to increase the power handling capability of the RF load. The input waveguide may be corrugated for HE11 mode input energy.

  15. APS high heat load monochromator

    Energy Technology Data Exchange (ETDEWEB)

    Lee, W.K.; Mills, D.

    1993-02-01

    This document contains the design specifications of the APS high heat load (HHL) monochromator and associated accessories as of February 1993. It should be noted that work is continuing on many parts of the monochromator including the mechanical design, crystal cooling designs, etc. Where appropriate, we have tried to add supporting documentation, references to published papers, and calculations from which we based our decisions. The underlying philosophy behind performance specifications of this monochromator was to fabricate a device that would be useful to as many APS users as possible, that is, the design should be as generic as possible. In other words, we believe that this design will be capable of operating on both bending magnet and ID beamlines (with the appropriate changes to the cooling and crystals) with both flat and inclined crystal geometries and with a variety of coolants. It was strongly felt that this monochromator should have good energy scanning capabilities over the classical energy range of about 4 to 20 keywith Si (111) crystals. For this reason, a design incorporating one rotation stage to drive both the first and second crystals was considered most promising. Separate rotary stages for the first and second crystals can sometimes provide more flexibility in their capacities to carry heavy loads (for heavily cooled first crystals or sagittal benders of second crystals), but their tuning capabilities were considered inferior to the single axis approach.

  16. Comparison of load parameters for stored materials

    DEFF Research Database (Denmark)

    Munch-Andersen, J.; Nielsen, J.

    1997-01-01

    that the wall friction measured in a silo might be significantly larger than the value obtained from shear tests. The load parameters depend on the load level, perhaps in a way not reflected by the internal friction angle. It is not necessarily on the safe side to determine the parameters for a high load level.......The load parameters listed in the european prestandard and those derived from the material tests conform reasonably well in many cases. There are, however, also many cases where the agreement is not satisfactory, especially due to larger variability of the measured values. This yields cretainly...... in several cases. The measurement of reliable and relevant wall friction coefficients is a severe problem. If the wall friction depends on if the normal load is increasing or decreasing, it is the value for increasing load which should be the relevant load parameter, but for coal and wheat it is seen...

  17. Loads in the design of flight vehicles

    Directory of Open Access Journals (Sweden)

    Simion TĂTARU

    2010-09-01

    Full Text Available The calculation of flight loads is a critical part of air vehicle design. On the other hand, the prediction of accurate loads is a sophisticated and complex process that requires skilled and experienced engineers. They must integrate results from wind tunnel tests, computer simulations, historical data and empirical formulations into a number of loads cases that provide a realistic assessment of the flight vehicle’s environment. Under these conditions, the vehicle must satisfy requirements imposed by regulatory agencies as part of the vehicle certification process.Loads and boundary conditions can be associated to either the finite element model or the underlying geometry. By associating loads and boundary conditions to the geometry the finite element model mesh and elements can be modified without redefining and applying the loads to the model. Loads and boundary conditions are associated to the model geometry by default.

  18. Effect of loading parameter on fretting fatigue

    Science.gov (United States)

    Kowser, Md. Arefin; Chowdhury, Mohammad Asaduzzaman; Shah, Quazi Md. Zobaer

    2017-06-01

    Fretting fatigue has become one of the major concern in the recent few decades since developed designs both structure's and complex engineering are facing with fatigue accompanied by friction. In this study, load factors as normal and bending forces influence on stress distribution along contact surface as well as fatigue life has been experimented by FEM analysis. Fatigue life is influenced prominently by variable fretting loads than variable tensile loadings. Maximum Von mises Stress and strain shows uniform horizontal straight line is found for maximum loading while for both type of bending, minimum loads yield the same character. It has been observed that stress distribution is more uniform for varying bending loads when variable fretting loads yield stress singularity nearer to the tip of contact between fretting pad and beam.

  19. Immediate non-occlusal loading vs. early loading in partially edentulous patients.

    Science.gov (United States)

    Testori, Tiziano; Bianchi, Francesca; Del Fabbro, Massimo; Szmukler-Moncler, Serge; Francetti, Luca; Weinstein, Roberto Ludovico

    2003-01-01

    Immediate loading of dental implants can reduce treatment time and management concerns, thus increasing patient acceptance. This paper reports the authors' preliminary experience with partially edentulous patients having received non-occlusally loaded provisional restorations within 24 hours of surgery, compared to patients treated according to an early loading protocol. The present data suggest that implant supported fixed partial prostheses can be immediately non-occlusally loaded and restored with a predictability similar to early loaded implants.

  20. Constant-load exercise decreases the serum concentration of myeloperoxidase in healthy smokers and smokers with COPD

    Directory of Open Access Journals (Sweden)

    Holz O

    2015-07-01

    Full Text Available Olaf Holz,1,* Stefan Roepcke,2,* Henrik Watz,3 Uwe Tegtbur,4 Gezim Lahu,2 Jens M Hohlfeld1 1Fraunhofer Institute for Toxicology and Experimental Medicine (ITEM, German Center for Lung Research (DZL, BREATH, Hannover, Germany; 2Takeda Pharmaceuticals International GmbH, Glattpark-Opfikon, Switzerland; 3Pulmonary Research Institute at Lung Clinic Grosshansdorf, German Center for Lung Research (DZL, ARCN, Grosshansdorf, 4Institute for Sports Medicine, Hannover Medical School (MHH, Hannover, Germany *These authors contributed equally to this work Abstract: There is an ongoing demand for easily accessible biomarkers related to pathophysiological processes in chronic obstructive pulmonary disease (COPD. Short-term intense exercise is known to increase the peripheral blood levels of cytokines. Therefore, we tested the potential and the repeatability of an exercise challenge to amplify seven serum biomarkers (interleukin 6 [IL6], C-reactive protein [CRP], myeloperoxidase [MPO], leukotriene B4, soluble intercellular adhesion molecule 1, soluble vascular cell adhesion molecule 1, and von Willebrand factor [VWF] in smokers with and without COPD. Twenty-three smokers with moderate COPD (GOLD 2 and 23 sex- and age-matched healthy smokers underwent up to 30-minute submaximal, constant-load exercise (75% of maximum work load on two occasions separated by 4 weeks (second challenge n=19/20. Serum samples were obtained before, 5 minutes after the start, at the end of exercise (maximum 30 minutes or until exhaustion, and after additional 20 minutes of rest. The median (interquartile range exercise time until exhaustion in the two challenges was 10.0 (4.0 minutes and 10.0 (8.0 minutes in smokers with COPD and 22.0 (16.0 minutes and 26.5 (14.5 minutes in healthy smokers. The exercise challenge significantly increased the serum concentrations of IL6 and VWF, but decreased the concentrations of MPO. Healthy smokers showed a significantly greater increase (at

  1. Dynamic loading of galvanized parts

    Directory of Open Access Journals (Sweden)

    Michal Černý

    2010-01-01

    Full Text Available This work is divided into two parts: the theoretical part includes actual knowledge and points of view about degradation processes in construction materials, anticorrosion protection, zinc coat composition and high frequency fatigue. The laboratory part follow-up existing regulations contents Czech standards and formulate specifications for acquisition of objective information from acceleration la­bo­ra­to­ry tests in condensation chests, mechanical high frequency fatigue tests on pulsator machine and possibilities of evaluation of fatigue tests. Laboratory findings declare to fundamental types of damage of constructions with anticorrosion protection in real loading conditions with dynamic high frequency character. Laboratory tests were made in sulphide and chloride environments.

  2. Greywater pollution variability and loadings

    DEFF Research Database (Denmark)

    Eriksson, Eva; Andersen, Henrik Rasmus; Madsen, Toke S.

    2009-01-01

    was proved not to be readily degradable. Ammonium content, presumably from urine contamination, was found to undergo nitrification in the RBC. Mass flow (daily loads) for individual substances was calculated for several pollutants. Macropollutants were found to be generated in low numbers of grams per person......Small on-site greywater treatment and reuse plants are susceptible to high short-term variation in flow and pollutant concentrations. As demonstrated in this study of a bathroom greywater plant in Copenhagen, Denmark, the flow ranges from no-flow periods to high-flow periods reaching 34 l min−1....... Concentrations of both macro- and micro-pollutants (organic matter and parabens) were found to range by several orders of magnitude in the influent, based on sampling every 20 min. Paraben degradation was proven to occur in the rotating biological contactor (RBC), while the remnant organic matter in the effluent...

  3. Impaired sleep and allostatic load

    DEFF Research Database (Denmark)

    Clark, Alice Jessie; Dich, Nadya; Lange, Theis

    2014-01-01

    Objective: Understanding the mechanisms linking sleep impairment to morbidity and mortality is important for future prevention, but these mechanisms are far from elucidated. We aimed to determine the relation between impaired sleep, both in terms of duration and disturbed sleep, and allostatic load...... Biobank with comprehensive information on sleep duration, disturbed sleep, objective measures of an extensive range of biological risk markers, and physical conditions. Results: Long sleep (mean difference 0.23; 95% confidence interval, 0.13, 0.32) and disturbed sleep (0.14; 0.06, 0.22) were associated...... with higher AL as well as with high-risk levels of risk markers from the anthropometric, metabolic, and immune system. Sub-analyses suggested that the association between disturbed sleep and AL might be explained by underlying disorders. Whereas there was no association between short sleep and AL...

  4. Active load control using microtabs

    Science.gov (United States)

    Yen, Dora Te-Lun

    2001-11-01

    Micro-electro-mechanical (MEM) translational tabs are introduced for enhancing and controlling the aerodynamic loading on lifting surfaces. These microtabs are mounted near the trailing edge of lifting surfaces, retract and extend approximately normal to the surface and have a maximum deployment height on the order of the boundary-layer thickness. Deployment of the device effectively modifies the camber distribution of the lifting surface and hence, the lift generated. The effect of the microtabs on lift is shown to be as powerful as conventional control surfaces with lift changes of 30%--50% in the linear range of the lift curve using a tab with a height of 1% of airfoil chord placed at 5% of chord upstream of the trailing edge on the lower surface. A multi-disciplinary approach incorporating aspects of experimental and computational aerodynamics, mechanical design and microfabrication techniques has been taken to develop and test a "proof of concept" model. Flow simulations, using a Reynolds-averaged Navier Stokes solver, have been conducted to optimize the size and placement of the devices based on trailing edge volume constraints. Numerical and experimental wind tunnel results are in good agreement, and both confirm that these micro-scale devices create macro-scale changes in aerodynamic loading. Application of this rather simple but innovative lift control system based on microfabrication techniques introduces a robust, dynamic control device and will allow for the miniaturization of conventional high lift and control systems. The result is a significant reduction in typical control system weight, complexity and cost. Also due to the minute size of these tabs, their activation and response times are much faster than that of conventional trailing edge devices. The "proof of concept" tab design, fabrication techniques, computational and experimental setup, and test results using a representative airfoil are presented in this research. (For more information, see

  5. Load to Failure and Stiffness

    Science.gov (United States)

    Esquivel, Amanda O.; Duncan, Douglas D.; Dobrasevic, Nikola; Marsh, Stephanie M.; Lemos, Stephen E.

    2015-01-01

    Background: Rotator cuff tendinopathy is a frequent cause of shoulder pain that can lead to decreased strength and range of motion. Failures after using the single-row technique of rotator cuff repair have led to the development of the double-row technique, which is said to allow for more anatomical restoration of the footprint. Purpose: To compare 5 different types of suture patterns while maintaining equality in number of anchors. The hypothesis was that the Mason-Allen–crossed cruciform transosseous-equivalent technique is superior to other suture configurations while maintaining equality in suture limbs and anchors. Study Design: Controlled laboratory study. Methods: A total of 25 fresh-frozen cadaveric shoulders were randomized into 5 suture configuration groups: single-row repair with simple stitch technique; single-row repair with modified Mason-Allen technique; double-row Mason-Allen technique; double-row cross-bridge technique; and double-row suture bridge technique. Load and displacement were recorded at 100 Hz until failure. Stiffness and bone mineral density were also measured. Results: There was no significant difference in peak load at failure, stiffness, maximum displacement at failure, or mean bone mineral density among the 5 suture configuration groups (P sutures in the repair should be considered to judge the strength of the repair. Clinical Relevance: Previous in vitro studies have shown the double-row rotator cuff repair to be superior to the single-row repair; however, clinical research does not necessarily support this. This study found no difference when comparing 5 different repair methods, supporting research that suggests the number of sutures and not the pattern can affect biomechanical properties. PMID:26665053

  6. Allostatic load and biological anthropology.

    Science.gov (United States)

    Edes, Ashley N; Crews, Douglas E

    2017-01-01

    Multiple stressors affect developing and adult organisms, thereby partly structuring their phenotypes. Determining how stressors influence health, well-being, and longevity in human and nonhuman primate populations are major foci within biological anthropology. Although much effort has been devoted to examining responses to multiple environmental and sociocultural stressors, no holistic metric to measure stress-related physiological dysfunction has been widely applied within biological anthropology. Researchers from disciplines outside anthropology are using allostatic load indices (ALIs) to estimate such dysregulation and examine life-long outcomes of stressor exposures, including morbidity and mortality. Following allostasis theory, allostatic load represents accumulated physiological and somatic damage secondary to stressors and senescent processes experienced over the lifespan. ALIs estimate this wear-and-tear using a composite of biomarkers representing neuroendocrine, cardiovascular, metabolic, and immune systems. Across samples, ALIs are associated significantly with multiple individual characteristics (e.g., age, sex, education, DNA variation) of interest within biological anthropology. They also predict future outcomes, including aspects of life history variation (e.g., survival, lifespan), mental and physical health, morbidity and mortality, and likely health disparities between groups, by stressor exposures, ethnicity, occupations, and degree of departure from local indigenous life ways and integration into external and commodified ones. ALIs also may be applied to similar stress-related research areas among nonhuman primates. Given the reports from multiple research endeavors, here we propose ALIs may be useful for assessing stressors, stress responses, and stress-related dysfunction, current and long-term cognitive function, health and well-being, and risk of early mortality across many research programs within biological anthropology. © 2017 American

  7. Load research manual. Volume 2. Fundamentals of implementing load research procedures

    Energy Technology Data Exchange (ETDEWEB)

    Brandenburg, L.; Clarkson, G.; Grund, Jr., C.; Leo, J.; Asbury, J.; Brandon-Brown, F.; Derderian, H.; Mueller, R.; Swaroop, R.

    1980-11-01

    This three-volume manual presents technical guidelines for electric utility load research. Special attention is given to issues raised by the load data reporting requirements of the Public Utility Regulatory Policies Act of 1978 and to problems faced by smaller utilities that are initiating load research programs. In Volumes 1 and 2, procedures are suggested for determining data requirements for load research, establishing the size and customer composition of a load survey sample, selecting and using equipment to record customer electricity usage, processing data tapes from the recording equipment, and analyzing the data. Statistical techniques used in customer sampling are discussed in detail. The costs of load research also are estimated, and ongoing load research programs at three utilities are described. The manual includes guides to load research literature and glossaries of load research and statistical terms.

  8. Multi-Capacity Load Cell Concept

    Directory of Open Access Journals (Sweden)

    Seif. M. OSMAN

    2014-09-01

    Full Text Available Force measuring systems are usually used to calibrate force generated systems, it is not preferable to use load cells to measure forces less than 10 % of its nominal capacity. Several load cells are required to offer calibration facilities at sites to cover different ranges, this lead to difficulties in handling procedures, through the need for several carrying cases to carry this overweight in addition to the over cost of purchasing several load cells. This article concerns with introducing a new concept for designing a multi-capacity load cell as a new force standard in the field of measuring the force. This multi-capacity load cell will replace a set of load cells and reflects economically on the total cost and on easiness of handling procedures.

  9. Static Load Distribution in Ball Bearings

    Science.gov (United States)

    Ricci, Mario

    2010-01-01

    A numerical procedure for computing the internal loading distribution in statically loaded, single-row, angular-contact ball bearings when subjected to a known combined radial and thrust load is presented. The combined radial and thrust load must be applied in order to avoid tilting between inner and outer rings. The numerical procedure requires the iterative solution of Z + 2 simultaneous nonlinear equations - where Z is the number of the balls - to yield an exact solution for axial and radial deflections, and contact angles. Numerical results for a 218 angular-contact ball bearing have been compared with those from the literature and show significant differences in the magnitudes of the ball loads, contact angles, and the extent of the loading zone.

  10. 1991 Pacific Northwest Loads and Resources Study.

    Energy Technology Data Exchange (ETDEWEB)

    United States. Bonneville Power Administration.

    1991-12-01

    This study establishes the Bonneville Power Administration's (BPA) planning basis for supplying electricity to BPA customers. The Loads and Resources Study is presented in three documents: (1) this summary of federal system and Pacific Northwest region loads and resources; (2) a technical appendix detailing forecasted Pacific Northwest economic trends and loads, and (3) a technical appendix detailing the loads and resources for each major Pacific Northwest generating utility. This analysis updates our 1990 study. BPS's long-range planning incorporates resource availability with a range of forecasted electrical consumption. The forecasted future electrical demands-firm loads--are subtracted from the projected capability of existing resources to determine whether BPA and the region will be surplus or deficit. If resources are greater than loads in any particular year or month, there is a surplus of energy and/or capacity, which BPA can sell to increase revenues. Conversely, if firm loads exceed available resources, there is a deficit of energy and/or capacity, then additional conservation, contract purchases, or generating resources will be needed to meet load growth. This study analyzes the Pacific Northwest's projected loads and available generating resources in two parts: (1) the loads and resources of the federal system, for which BPA is the marketing agency; and (2) the larger Pacific Northwest regional profile, which includes loads and resources in addition to the federal system. This study presents the federal system and regional analyses for five load forecasts: high, medium-high, medium, medium-low, and low. This analysis projects the yearly average energy consumption and resource availability for 1992- 2012.

  11. Loads in the design of flight vehicles

    OpenAIRE

    Simion TĂTARU; Radu BÎSCĂ; Dorin LOZICI-BRÎNZEI

    2010-01-01

    The calculation of flight loads is a critical part of air vehicle design. On the other hand, the prediction of accurate loads is a sophisticated and complex process that requires skilled and experienced engineers. They must integrate results from wind tunnel tests, computer simulations, historical data and empirical formulations into a number of loads cases that provide a realistic assessment of the flight vehicle’s environment. Under these conditions, the vehicle must satisfy requirements im...

  12. Cyclic Triaxial Loading of Cohesionless Silty Sand

    DEFF Research Database (Denmark)

    Sabaliauskas, Tomas; Ibsen, Lars Bo

    2015-01-01

    To engineer efficient structures offshore, we need to extend our knowledge of soil response. Cyclic loading and high water pressure encountered offshore greatly influence cohesionless soil performance. Silty sand from Frederikshavn wind turbine farm was tested using single diameter height samples...... with lubricated, smooth boundary piston heads in a Danish triaxial apparatus. Samples were successfully subjected to loading histories of high complexity. Loading include high strains and stresses, post liquefaction response, transitioning through multiple densities and restoring initial soil properties after...

  13. Fatigue durability under random cyclic loading

    Science.gov (United States)

    Volkov, S. S.; Struzhanov, V. V.

    2017-12-01

    Methods for predicting the durability of metals have been developed while taking into account the effect of random loads acting during the service life of structures. Methods of the theory of functions of random variables are applied. Normal distribution and the Rayleigh distribution are used to estimate the random loads from the experimental histogram. A numerical example illustrates the influence of the statistical parameters of the load distribution on the predicted number of cycles before failure.

  14. Valproic acid loading during intensive monitoring.

    Science.gov (United States)

    Rosenfeld, W E; Leppik, I E; Gates, J R; Mireles, R E

    1987-07-01

    Of 35 patients who had generalized tonic-clonic seizures during antiepileptic drug therapy withdrawal, "loading" with valproic acid was effective in limiting these seizures in 32 patients. A loading dose of approximately 12.5 mg/kg was used. This dose resulted in valproic acid levels between 284 and 458 mumol/L (41 and 66 mg/L) 1.5 hours after "loading" in six of the eight patients in whom serum concentrations were measured.

  15. Timber joints under long-term loading

    DEFF Research Database (Denmark)

    Feldborg, T.; Johansen, M.

    This report describes tests and results from stiffness and strength testing of splice joints under long-term loading. During two years of loading the spicimens were exposed to cyclically changing relative humidity. After the loading period the specimens were short-term tested. The connectors were...... integral nail-plates and nailed steel and plywood gussets. The report is intended for designers and researchers in timber engineering....

  16. The load intesity of florbal players

    OpenAIRE

    Niklas, Martin

    2012-01-01

    Title: The load intensity of floorball players. Objectives: The aim of the work is to compare the load intensity of floorball players in training unit and in competitive match. Methods: To measure the intensity of loading was selected set of floorbal players from extraleague team. Then was performed their measuring heart rate by sport testers in the training unit and in the competitive match. Results: The results of measurement showed a higher average and maximum heart rate of players during ...

  17. Assessment of wind turbine load measurement instrumentation

    Energy Technology Data Exchange (ETDEWEB)

    Morfiadakis, E.; Papadopoulos, K. [CRES (Greece); Borg, N. van der [ECN, Petten (Netherlands); Petersen, S.M. [Risoe, Roskilde (Denmark); Seifert, H. [DEWI, Wilhelmshaven (Germany)

    1999-03-01

    In the framework of Sub-Task3 `Wind turbine load measurement instrumentation` of EU-project `European Wind Turbine Testing Procedure Development`, the load measurement techniques have been assessed by laboratory, full scale and numerical tests. The existing methods have been reviewed with emphasis on the strain gage application techniques on composite materials and recommendations are provided for the optimisation of load measurement techniques. (au) EU. 14 refs.

  18. Dietary acid load and renal function have varying effects on blood acid-base status and exercise performance across age and sex.

    Science.gov (United States)

    Hietavala, Enni-Maria; Stout, Jeffrey R; Frassetto, Lynda A; Puurtinen, Risto; Pitkänen, Hannu; Selänne, Harri; Suominen, Harri; Mero, Antti A

    2017-12-01

    Diet composition influences acid-base status of the body. This may become more relevant as renal functional capacity declines with aging. We examined the effects of low (LD) versus high dietary acid load (HD) on blood acid-base status and exercise performance. Participants included 22 adolescents, 33 young adults (YA), and 33 elderly (EL), who followed a 7-day LD and HD in a randomized order. At the end of both diet periods the subjects performed a cycle ergometer test (3 × 10 min at 35%, 55%, 75%, and (except EL) until exhaustion at 100% of maximal oxygen uptake). At the beginning of and after the diet periods, blood samples were collected at rest and after all workloads. Oxygen uptake, respiratory exchange ratio (RER), and heart rate (HR) were monitored during cycling. In YA and EL, bicarbonate (HCO 3 - ) and base excess (BE) decreased over the HD period, and HCO 3 - , BE, and pH were lower at rest after HD compared with LD. In YA and EL women, HCO 3 - and BE were lower at submaximal workloads after HD compared with LD. In YA women, the maximal workload was 19% shorter and maximal oxygen uptake, RER, and HR were lower after HD compared with LD. Our data uniquely suggests that better renal function is associated with higher availability of bases, which may diminish exercise-induced acidosis and improve maximal aerobic performance. Differences in glomerular filtration rate between the subject groups likely explains the larger effects of dietary acid load in the elderly compared with younger subjects and in women compared with men.

  19. Load relaxation studies of zircaloy-4

    Energy Technology Data Exchange (ETDEWEB)

    Huang, F.H.; Sabol, G.P.; McDonald, S.G.; Li, C.Y.

    1976-01-01

    The results of the present work have shown (1) the load relaxation data of Zircaloy-4 in the temperature range of 200/sup 0/C to 385/sup 0/C can be represented by the phenomenological model based on Hart's plastic equation of state; (2) the room temperature load relaxation data reflect the effects of deformation twinning; (3) at higher temperatures the load relaxation data suggest the contribution of grain boundary sliding; and (4) the effects of strain aging can be identified based on the load relaxation data.

  20. Behaviour of Cohesionless Soils During Cyclic Loading

    DEFF Research Database (Denmark)

    Shajarati, Amir; Sørensen, Kris Wessel; Nielsen, Søren Kjær

    Offshore wind turbine foundations are typically subjected to cyclic loading from both wind and waves, which can lead to unacceptable deformations in the soil. However, no generally accepted standardised method is currently available, when accounting for cyclic loading during the design of offshore...... wind turbine foundations. Therefore a literature study is performed in order to investigate existing research treating the behaviour of cohesionless soils, when subjected to cyclic loading. The behaviour of a soil subjected to cyclic loading is found to be dependent on; the relative density, mean...

  1. Load prediction of stall regulated wind turbines

    Energy Technology Data Exchange (ETDEWEB)

    Bjoerck, A.; Dahlberg, J.Aa. [Aeronautical Research Inst. of Sweden, Bromma (Sweden); Carlen, I. [Chalmers Univ. of Technology, Goeteborg (Sweden). Div. of Marine Structural Engineering; Ganander, H. [Teknikgruppen AB, Sollentua (Sweden)

    1996-12-01

    Measurements of blade loads on a turbine situated in a small wind farm shows that the highest blade loads occur during operation close to the peak power i.e. when the turbine operates in the stall region. In this study the extensive experimental data base has been utilised to compare loads in selected campaigns with corresponding load predictions. The predictions are based on time domain simulations of the wind turbine structure, performed by the aeroelastic code VIDYN. In the calculations a model were adopted in order to include the effects of dynamic stall. This paper describes the work carried out so far within the project and key results. 5 refs, 10 figs

  2. Comparison of Temperature Loadings of Bridge Girders

    Directory of Open Access Journals (Sweden)

    J. Římal

    2008-01-01

    Full Text Available This paper compares the effect of temperature changes on the superstructure of bridges, above all the effect of non-uniform temperature. Loadings according to standards ESN 73 6203, ENV 1991-1-5 and DIN 1072 are compared here. The paper shows a short summary of temperature loading according to each standard and shows the comparison of bending moments arisen from these temperature loadings on superstructure made from continuous girder from a steel-concrete box girder with a composite concrete slab. With respect to a variety of design processes, the comparison is made without any coefficient of loading, combination or material. 

  3. Safety Harness For Work Under Suspended Load

    Science.gov (United States)

    Sunoo, Su Young

    1994-01-01

    Safety device protects worker under suspended engine or other heavy load. Mechanically linked with load so if load should fall, worker yanked safely away. Worker wears chest-plate vest with straps crossing eye on back. Lower safety cable connected to eye extends horizontally away from worker to nearby wall, wrapped on pulley and extends upward to motion amplifier or reducer. Safety cables transform any sudden downward motion of overhanging load into rapid sideways motion of worker. Net catches worker, preventing worker from bumping against wall.

  4. System and method employing a self-organizing map load feature database to identify electric load types of different electric loads

    Science.gov (United States)

    Lu, Bin; Harley, Ronald G.; Du, Liang; Yang, Yi; Sharma, Santosh K.; Zambare, Prachi; Madane, Mayura A.

    2014-06-17

    A method identifies electric load types of a plurality of different electric loads. The method includes providing a self-organizing map load feature database of a plurality of different electric load types and a plurality of neurons, each of the load types corresponding to a number of the neurons; employing a weight vector for each of the neurons; sensing a voltage signal and a current signal for each of the loads; determining a load feature vector including at least four different load features from the sensed voltage signal and the sensed current signal for a corresponding one of the loads; and identifying by a processor one of the load types by relating the load feature vector to the neurons of the database by identifying the weight vector of one of the neurons corresponding to the one of the load types that is a minimal distance to the load feature vector.

  5. Measuring training load in sports.

    Science.gov (United States)

    Lambert, Michael Ian; Borresen, Jill

    2010-09-01

    The principle of training can be reduced to a simple "dose-response" relationship. The "response" in this relationship can be measured as a change in performance or the adaptation of a physiological system. The "dose" of training, or physiological stress associated with the training load, is more difficult to measure as there is no absolute "gold standard" which can be used in the field, making it difficult to validate procedures. Attempts have been made to use heart rate as a marker of intensity during training, but the theoretical attractiveness of this method is not supported by the accuracy and the practicality of using this method during training or competition. The session RPE, based on the product of training duration and perceived intensity is more practical and can be used in a variety of sports. However, the score depends on a subjective assessment, and the intersubject comparisons may be inaccurate. The demands of different sports vary and therefore the methods of assessing training need to vary accordingly. The time has come to reach consensus on assessing training accurately in different sports. There is a precedent for this consensus approach with scientists having already done so for the assessment of physical activity, and for defining injuries in rugby, football and cricket. Standardizing these methods has resulted in the quality of research in these areas increasing exponentially.

  6. Wind loading on solar collectors

    Energy Technology Data Exchange (ETDEWEB)

    Bhaduri, S.; Murphy, L.M.

    1985-06-01

    The present design methodology for the determination of wind loading on the various solar collectors has been reviewed and assessed. The total force coefficients of flat plates of aspect ratios 1.0 and 3.0, respectively, at various angles of attack obtained by using the guidelines of the ANSI A58.1-1982, have been compared with those obtained by using the methodology of the ASCE Task Committee, 1961, and the experimental results of the full-scale test of heliostats by Peglow. The turbulent energy spectra, currently employed in the building code, are compared with those of Kaimal et al., Lumley, and Ponofsky for wind velocities of 20.0 m/s and 40.24 m/s at an elevation of 9.15 m. The longitudinal spectra of the building code overestimates the Kaimal spectra in the frequency range of 0.007 Hz to 0.08 Hz and underestimates beyond the frequency of 0.08 Hz. The peak angles of attack, on the heliostat, stowed in horizontal position, due to turbulent vertical and lateral components of wind velocity, have been estimated by using Daniel's methodology for three wind velocities and compared with the value suggested by the code. The experimental results of a simple test in the laboratory indicate the feasibility of decreasing the drag forces of the flat plate by reducing the solidity ratio.

  7. Procedures for Calculating Residential Dehumidification Loads

    Energy Technology Data Exchange (ETDEWEB)

    Winkler, Jon [National Renewable Energy Lab. (NREL), Golden, CO (United States); Booten, Chuck [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-06-01

    Residential building codes and voluntary labeling programs are continually increasing the energy efficiency requirements of residential buildings. Improving a building's thermal enclosure and installing energy-efficient appliances and lighting can result in significant reductions in sensible cooling loads leading to smaller air conditioners and shorter cooling seasons. However due to fresh air ventilation requirements and internal gains, latent cooling loads are not reduced by the same proportion. Thus, it's becoming more challenging for conventional cooling equipment to control indoor humidity at part-load cooling conditions and using conventional cooling equipment in a non-conventional building poses the potential risk of high indoor humidity. The objective of this project was to investigate the impact the chosen design condition has on the calculated part-load cooling moisture load, and compare calculated moisture loads and the required dehumidification capacity to whole-building simulations. Procedures for sizing whole-house supplemental dehumidification equipment have yet to be formalized; however minor modifications to current Air-Conditioner Contractors of America (ACCA) Manual J load calculation procedures are appropriate for calculating residential part-load cooling moisture loads. Though ASHRAE 1% DP design conditions are commonly used to determine the dehumidification requirements for commercial buildings, an appropriate DP design condition for residential buildings has not been investigated. Two methods for sizing supplemental dehumidification equipment were developed and tested. The first method closely followed Manual J cooling load calculations; whereas the second method made more conservative assumptions impacting both sensible and latent loads.

  8. Mechanical behavior of cyclically loaded PZT

    Energy Technology Data Exchange (ETDEWEB)

    White, G.S.; Hill, M.D.; Freiman, S.W. [National Inst. of Standards and Technology, Gaithersburg, MD (United States); Hwang, C.S. [Seoul National Univ. (Korea, Republic of)

    1994-12-31

    Uses of intelligent materials which involve the application of force or the generation of displacements will require the incorporation of some form of actuator material into the overall structure. Typically, these types of applications will result in the generation of cyclic loads on the actuator; depending upon the specific application, the frequency of the loading could be low, e.g., for positioning components, or relatively high, e.g., for damping out vibrations in machining tools. Nevertheless, the cyclic nature of the loading raises the specter of damage and, ultimately, failure arising from cyclic loading processes which would not be predicted by traditional mechanical properties test methods. It has been found that PZT loaded cyclically sometimes fails at loads below its nominal strength, as measured by traditional, monotonically increasing load tests. Damage mechanisms which come into play as a result of the cyclic loading conditions have been postulated as the reasons for this behavior. Recent work investigating the cyclic loading of a PZT-8 material at resonance frequency determined that microcracks were generated in the high stress region of the material. Recent results demonstrate that macrocrack extension appears to be accompanied by domain reorientation whereas microcracks can propagate around PZT grains without affecting the domains, (2) morphology and distribution of microcracks generated under different loading conditions can change dramatically that the qualitative mechanical response of PZT-8 to cyclic loading appears to be insensitive to grain morphology. The results presented imply that stresses generated at the tips of macrocracks are much larger than those at microcracks, that temperature strongly affects the rate of microcrack generation, and that wide distributions in grain size and the presence of large voids do not necessarily result in increased microcrack generation over that seen in 2 {micro}m grain size, small pore material.

  9. Behaviour of glass plates under wind loads

    Science.gov (United States)

    Gavanski, Eri

    Glazing damage during strong windstorms has been considered to result mainly from windborne debris. However, recent windstorm damage reports have revealed the necessity of studying fluctuating wind loads, which appear to be another factor contributing to this damage. From an experimental point of view, studies on this topic have been limited to the application of rather simple loading patterns. Moreover, there is an uncertainty surrounding both load resistance and design load used in the current North American window glass design codes. It is of concern that these regulations may not offer sufficient accuracy on account of the limited understanding of time-dependent glass strength derived from the technology available at the time of codification. Unprecedented full-scale glass breakage tests under realistic wind pressure loading were conducted to investigate these issues. The obtained results revealed significant new information about the behavior of glass plates under fluctuating loads. Along with these tests, a numerical simulation using the Monte-Carlo technique was also performed with a subtle modification of the initial glass strength. This adjustment resulted in better correspondence with test results. Using the test and numerical simulation results, the current window glass design method was examined. The calculation methods of LR, and the reference time conversion used in the codes, were found to require further investigation. By creating a particular wind pressure time history, the practice of using peak pressures from ASCE7-05 as the design load was investigated. The results showed that there are cases when the current practice may underestimate the design load because of the duration of windstorms. KEYWORDS: Glass, Fluctuating load, Full-scale test, Load resistance, Design load, Static fatigue, Numerical simulation, Monte-Carlo technique, Brown's integral.

  10. Demonstration of load rating capabilities through physical load testing : Johnson County bridge case study.

    Science.gov (United States)

    2013-08-01

    The objective of this work, Pilot Project - Demonstration of Capabilities and Benefits of Bridge Load Rating through Physical Testing, was to demonstrate the capabilities for load testing and rating bridges in Iowa, study the economic benefit of perf...

  11. Demonstration of load rating capabilities through physical load testing : Sioux County bridge case study.

    Science.gov (United States)

    2013-08-01

    The objective of this work, Pilot Project - Demonstration of Capabilities and Benefits of Bridge Load Rating through Physical Testing, was to demonstrate the capabilities for load testing and rating bridges in Iowa, study the economic benefit of perf...

  12. Demonstration of load rating capabilities through physical load testing : Ida County bridge case study.

    Science.gov (United States)

    2013-08-01

    The objective of this work, Pilot Project - Demonstration of Capabilities and Benefits of Bridge Load Rating through Physical Testing, was to demonstrate the capabilities for load testing and rating bridges in Iowa, study the economic benefit of perf...

  13. Definition of a Comprehensive Loads Process in the DLR Project iLOADS

    OpenAIRE

    Krüger, Wolf R.; Klimmek, Thomas

    2016-01-01

    The determination of loads acting on the aircraft is one of the main tasks during aircraft development. The knowledge of loads is important for aircraft design, e.g. for the sizing of the airframe structure, and also for certification. The definition of realistic loads assumptions is important, as well as the generation of loads from simulation and experiment. DLR is involved in a large number of aircraft design activities, and operates a fleet of research aircraft; thus DLR requires in-depth...

  14. Strategies for Controlling Plug Loads. A Tool for Reducing Plug Loads in Commercial Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Torcellini, Paul [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bonnema, Eric [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sheppy, Michael [National Renewable Energy Lab. (NREL), Golden, CO (United States); Pless, Shanti [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2015-09-01

    Plug loads are often not considered as part of the energy savings measures in Commercial Buildings; however, they can account for up to 50% of the energy used in the building. These loads are numerous and often scattered throughout a building. Some of these loads are purchased by the owner and some designed into the building or the tenant finishes for a space. This document provides a strategy and a tool for minimizing these loads.

  15. Load power device and system for real-time execution of hierarchical load identification algorithms

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Yi; Madane, Mayura Arun; Zambare, Prachi Suresh

    2017-11-14

    A load power device includes a power input; at least one power output for at least one load; and a plurality of sensors structured to sense voltage and current at the at least one power output. A processor is structured to provide real-time execution of: (a) a plurality of load identification algorithms, and (b) event detection and operating mode detection for the at least one load.

  16. Comparison of the loading rate in various types of swimming with load.

    OpenAIRE

    Pospíšek, Tomáš

    2013-01-01

    Title of work Comparison of the loading rate in various types of swimming with load. Work objective Comparison of physical intensity in selected types of swimming with load used in the ACR. The level of physical intensity was determined on the basis of measured heart rate at different styles of swimming with load. Used methods The method used in this work was quantitative research with the observation of how the organism responds to the stress. There were 4 people tested. The measurement was ...

  17. Reducing the Cognitive Load on Novice Programmers.

    Science.gov (United States)

    Garner, Stuart

    Computer programming is a domain of knowledge that is generally considered difficult by students, many of whom experience low levels of achievement and become disillusioned. This paper suggests that cognitive load theory needs to be taken into account when designing instructional materials for this domain. The cognitive load that is experienced by…

  18. A case study of micromachined load cell

    Indian Academy of Sciences (India)

    silicon dioxide grown on a silicon substrate. When the load is applied, the sensing element deforms and causes the change in resistance due to stresses and the piezo-resistive property change. The proposed layout of the sensing element to be used in the load cell is shown in figure 1. All the four gauges are deposited on ...

  19. Controllable Load Management Approaches in Smart Grids

    Directory of Open Access Journals (Sweden)

    Jingshuang Shen

    2015-10-01

    Full Text Available With rapid smart grid technology development, the customer can actively participate in demand-side management (DSM with the mutual information communication between the distributor operation company and the smart devices in real-time. Controllable load management not only has the advantage of peak shaving, load balance, frequency regulation, and voltage stability, but is also effective at providing fast balancing services to the renewable energy grid in the distributed power system. The load management faces an enormous challenge as the customer has a large number of both small residential loads and dispersed renewable sources. In this paper, various controllable load management approaches are discussed. The traditional controllable load approaches such as the end users’ controllable appliances, storage battery, Vehicle-to-Grid (V2G, and heat storage are reviewed. The “broad controllable loads” management, such as the microgrid, Virtual Power Plant (VPP, and the load aggregator are also presented. Furthermore, the load characteristics, control strategies, and control effectiveness are analyzed.

  20. Load-Bearing Capacity of Roof Trusses

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Damkilde, Lars; Munch-Andersen, J.

    2004-01-01

    systems such as roof trusses are established and statistical characteristics of the load bearing capacity are determined. The results show that there is a significant increase in the characteristic (nominal) value and a reduction in the coefficient of variation (COV) for typical loads such as permanent...

  1. Cell Load Balancing in Heterogeneous Scenarios

    DEFF Research Database (Denmark)

    Eduardo, Simao; Rodrigues, Antonio; Mihovska, Albena D.

    2013-01-01

    Cell load imbalances in wireless networks degrade performance. Macro and small cell collocated deployments (heterogeneous scenario) constitutes a new problem for load balancing. This paper proposes a novel admission control algorithm for an optimal solution to the assignment of traffic flows...

  2. Modelling and Simulation of Wave Loads

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Thoft-Christensen, Palle

    1985-01-01

    A simple model of the wave load on stender members of offshore structures is described . The wave elevation of the sea stateis modelled by a stationary Gaussian process. A new procedure to simulate realizations of the wave loads is developed. The simulation method assumes that the wave particle...

  3. Using Electroencephalography to Measure Cognitive Load

    Science.gov (United States)

    Antonenko, Pavlo; Paas, Fred; Grabner, Roland; van Gog, Tamara

    2010-01-01

    Application of physiological methods, in particular electroencephalography (EEG), offers new and promising approaches to educational psychology research. EEG is identified as a physiological index that can serve as an online, continuous measure of cognitive load detecting subtle fluctuations in instantaneous load, which can help explain effects of…

  4. Fruit load governs transpiration of olive trees

    NARCIS (Netherlands)

    Bustan, Amnon; Dag, Arnon; Yermiyahu, Uri; Erel, Ran; Presnov, Eugene; Agam, Nurit; Kool, Dilia; Iwema, Joost; Zipori, Isaac; Ben-Gal, Alon

    2016-01-01

    We tested the hypothesis that whole-tree water consumption of olives (Olea europaea L.) is fruit load-dependent and investigated the driving physiological mechanisms. Fruit load was manipulated in mature olives grown in weighing-drainage lysimeters. Fruit was thinned or entirely removed from

  5. Baseline axle load survey in Malawi - 2014

    CSIR Research Space (South Africa)

    Roux, M

    2015-07-01

    Full Text Available As part of the project to update the Malawian Directorate of Road Transport and Safety Services’ (DRTSS) 2005 Axle Load Control Strategy and to provide a five-year implementation plan, a country-wide axle load survey was undertaken to assess...

  6. Concrete structures under impact loading rate effects

    NARCIS (Netherlands)

    Zielinski, A.J.

    1984-01-01

    Various structures may be subjected to accidental, impact loading. The behaviour of structures under that kind of extreme loading conditions is of vital importance for people's safety and environmental damage prevention. There is a need for reliable assessment methods for the local and the overall

  7. Critical loads of heavy metals for soils

    NARCIS (Netherlands)

    Vries, de W.; Groenenberg, J.E.; Lofts, S.; Tipping, E.; Posch, M.

    2012-01-01

    To enable a precautionary risk assessment for future inputs of metals, steady-state methods have been developed to assess critical loads of metals avoiding long-term risks to food quality and eco-toxicological effects on organisms in soils and surface waters. A critical load for metals equals the

  8. Identification of dynamic load for prosthetic structures.

    Science.gov (United States)

    Zhang, Dequan; Han, Xu; Zhang, Zhongpu; Liu, Jie; Jiang, Chao; Yoda, Nobuhiro; Meng, Xianghua; Li, Qing

    2017-12-01

    Dynamic load exists in numerous biomechanical systems, and its identification signifies a critical issue for characterizing dynamic behaviors and studying biomechanical consequence of the systems. This study aims to identify dynamic load in the dental prosthetic structures, namely, 3-unit implant-supported fixed partial denture (I-FPD) and teeth-supported fixed partial denture. The 3-dimensional finite element models were constructed through specific patient's computerized tomography images. A forward algorithm and regularization technique were developed for identifying dynamic load. To verify the effectiveness of the identification method proposed, the I-FPD and teeth-supported fixed partial denture structures were investigated to determine the dynamic loads. For validating the results of inverse identification, an experimental force-measuring system was developed by using a 3-dimensional piezoelectric transducer to measure the dynamic load in the I-FPD structure in vivo. The computationally identified loads were presented with different noise levels to determine their influence on the identification accuracy. The errors between the measured load and identified counterpart were calculated for evaluating the practical applicability of the proposed procedure in biomechanical engineering. This study is expected to serve as a demonstrative role in identifying dynamic loading in biomedical systems, where a direct in vivo measurement may be rather demanding in some areas of interest clinically. Copyright © 2017 John Wiley & Sons, Ltd.

  9. Load Extrapolation During Operation for Wind Turbines

    DEFF Research Database (Denmark)

    Toft, Henrik Stensgaard; Sørensen, John Dalsgaard

    2008-01-01

    In the recent years load extrapolation for wind turbines has been widely considered in the wind turbine industry. Loads on wind turbines during operations are normally dependent on the mean wind speed, the turbulence intensity and the type and settings of the control system. All these parameters...

  10. 14 CFR 23.427 - Unsymmetrical loads.

    Science.gov (United States)

    2010-01-01

    ... Balancing Surfaces § 23.427 Unsymmetrical loads. (a) Horizontal surfaces other than main wing and their..., wings, horizontal surfaces other than main wing, and fuselage shape: (1) 100 percent of the maximum loading from the symmetrical flight conditions may be assumed on the surface on one side of the plane of...

  11. Multi-Capacity Load Cell Concept

    National Research Council Canada - National Science Library

    Seif M Osman; Ebtisam H Hasan; H M El-Hakeem; R M Rashad; F Kouta

    2014-01-01

    ... to carry this overweight in addition to the over cost of purchasing several load cells. This article concerns with introducing a new concept for designing a multi-capacity load cell as a new force standard in the field of measuring the force...

  12. Traffic load effects in prestrssed concrete bridges

    NARCIS (Netherlands)

    Vrouwenvelder, A.C.W.M.; Allaix, D.L.; Courage, W.M.G.

    2007-01-01

    The traffic load effect of a two-span prestressed concrete bridge with two traffic lanes is analyzed in this paper. The design value of the result-ing bending moment in some prescribed sections is estimated by means of a Monte Carlo simulation. The model for the vehicular loads is derived from a set

  13. Macrophyte Community Response to Nitrogen Loading and ...

    Science.gov (United States)

    Empirical determination of nutrient loading thresholds that negatively impact seagrass communities have been elusive due to the multitude of factors involved. Using a mesocosm system that simulated Pacific Northwest estuaries, we evaluated macrophyte metrics across gradients of NO3 loading (0, 1.5, 3 and 6x ambient) and temperature (10 and 20 °C). Macroalgal growth, biomass, and C:N responded positively to increased NO3 load and floating algal mats developed at 20 ºC. Zostera japonica metrics, including C:N, responded more to temperature than to NO3 loading. Z. marina biomass exhibited a negative temperature effect and in some cases a negative NO3 effect, while growth rate increased with temperature. Shoot survival decreased at 20 ºC but was not influenced by NO3 loading. Wasting disease index exhibited a significant temperature by NO3 interaction consistent with increased disease susceptibility. Community shifts observed were consistent with the nutrient loading hypothesis at 20 ºC, but there was no evidence of other eutrophication symptoms due to the short residence time. The Nutrient Pollution Index tracked the NO3 gradient at 10 ºC but exhibited no response at 20 ºC. We suggest that systems characterized by cool temperatures, high NO3 loads, and short residence time may be resilient to many symptoms of eutrophication. Estuarine systems characterized by cool temperatures, high nutrient loads and rapid flushing may be resilient to some symptoms

  14. Duration of load effects of solid wood

    DEFF Research Database (Denmark)

    Svensson, Staffan

    Test methods for studying the effect of long-term loading on the load carrying capacity of structural wood are discussed. The impact of sampling procedures on test results is investigated and is exemplified. It is concluded from this investigation that the sampling method has a significant impact...

  15. Suction caissons subjected to monotonic combined loading

    DEFF Research Database (Denmark)

    Penzes, P.; Jensen, M.R.; Zania, Varvara

    2016-01-01

    for offshore wind turbines. The combined loading imposed typically to a suction caisson has led to the estimation of their bearing capacity by means of 3D failure envelopes. This study aims to analyse the behaviour of suction caissons for offshore wind turbines subjected to combined loading. Finite element...

  16. Simulating liquid loading in gas wells

    NARCIS (Netherlands)

    Schiferli, W.; Belfroid, S.P.C.; Savenko, S.; Veeken, C.A.M.; Hu, B.

    2010-01-01

    This paper describes work performed by the authors over the last several years to better understand the factors affecting the onset of liquid loading. To further improve the prediction of onset of liquid loading, efforts were undertaken to better model the process. Dedicated codes as well as a

  17. Damage Accumulation in Vertical Breakwaters due to Combined Impact Loading and Pulsating Wave Loads

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Nielsen, Søren R. K.

    1999-01-01

    Vertical wall breakwaters used to protect for example an harbour from large waves usually consist of large concrete caissons placed on the seabed. The wave loads can be divided in two types, pulsating and impact loads. For some types of breakwaters especially the impact wave loads can be very large...

  18. on the correctness of load loss factor correctness of load loss factor ...

    African Journals Online (AJOL)

    eobe

    Author Tel: +44 -753-526-7242. TECHNICAL NOTE: TECHNICAL NOTE: ON THE CORRECTNESS OF LOAD LOSS FACTOR. CORRECTNESS OF LOAD LOSS FACTOR. CORRECTNESS OF LOAD LOSS FACTOR. A. O. Ekwue*. JACOBS ENGINEERING INC/BRUNEL UNIVERSITY LONDON,UNITED KINGDOM.

  19. 14 CFR 29.511 - Ground load: unsymmetrical loads on multiple-wheel units.

    Science.gov (United States)

    2010-01-01

    ... multiple-wheel units. 29.511 Section 29.511 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... Requirements Ground Loads § 29.511 Ground load: unsymmetrical loads on multiple-wheel units. (a) In dual-wheel gear units, 60 percent of the total ground reaction for the gear unit must be applied to one wheel and...

  20. Modelling of Generic Slung Load System

    DEFF Research Database (Denmark)

    Bisgaard, Morten; Bendtsen, Jan Dimon; La Cour-Harbo, Anders

    2006-01-01

    This paper presents the result of modelling and verification of a generic slung load system using a small-scale helicopter. The model is intended for use in simulation, pilot training, estimation, and control. The model is derived using a redundant coordinate formulation based on Gauss Principle...... of Least Constraint using the Udwadia-Kalaba equation and can be used to model all body to body slung load suspension types. The model gives an intuitive and easy-to-use way of modelling and simulating di erent slung load suspension types and it includes detection and response of wire slacking...... and tightening, and aerodynamical coupling between the helicopter and the load. Furthermore, it is shown how the model can be easily used for multi-lift systems either with multiple helicopers or multiple loads. A numerical stabilisation algorithm as well as a trim algorithm is presented for the complete...

  1. Modeling of Generic Slung Load System

    DEFF Research Database (Denmark)

    Bisgaard, Morten; Bendtsen, Jan Dimon; la Cour-Harbo, Anders

    2009-01-01

    This paper presents the result of the modelling and verification of a generic slung load system using a small-scale helicopter. The model is intended for use in simulation, pilot training, estimation, and control. The model is derived using a redundant coordinate formulation based on Gauss......' Principle of Least Constraint using the Udwadia-Kalaba equation and can be used to model all body to body slung load suspension types. The model provides intuitive and easy-to-use means of modelling and simulating different slung load suspension types. It includes detection of, and response to, wire...... slackening and tightening as well as aerodynamic coupling between the helicopter and the load. Furthermore, it is shown how the model can be easily used for multi-lift systems either with multiple helicopters or multiple loads. A numerical stabilisation algorithm is introduced and finally the use...

  2. A methodology for Electric Power Load Forecasting

    Directory of Open Access Journals (Sweden)

    Eisa Almeshaiei

    2011-06-01

    Full Text Available Electricity demand forecasting is a central and integral process for planning periodical operations and facility expansion in the electricity sector. Demand pattern is almost very complex due to the deregulation of energy markets. Therefore, finding an appropriate forecasting model for a specific electricity network is not an easy task. Although many forecasting methods were developed, none can be generalized for all demand patterns. Therefore, this paper presents a pragmatic methodology that can be used as a guide to construct Electric Power Load Forecasting models. This methodology is mainly based on decomposition and segmentation of the load time series. Several statistical analyses are involved to study the load features and forecasting precision such as moving average and probability plots of load noise. Real daily load data from Kuwaiti electric network are used as a case study. Some results are reported to guide forecasting future needs of this network.

  3. Simulation of Stochastic Loads for Fatigue Experiments

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Brincker, Rune

    1989-01-01

    A simple direct simulation method for stochastic fatigue-load generation is described in this paper. The simulation method is based on the assumption that only the peaks of the load process significantly affect the fatigue life. The method requires the conditional distribution functions of load...... process by a Markov process. Two different spectra from two tubular joints in an offshore structure (one narrow banded and one wide banded) are considered in an example. The results show that the simple direct method is quite efficient and results in a simulation speed of about 3000 load cycles per second...... ranges given the last peak values. Analytical estimates of these distribution functions are presented in the paper and compared with estimates based on a more accurate simulation method. In the more accurate simulation method samples at equidistant times are generated by approximating the stochastic load...

  4. Improved Load Shedding Scheme considering Distributed Generation

    DEFF Research Database (Denmark)

    Das, Kaushik; Nitsas, Antonios; Altin, Müfit

    2017-01-01

    With high penetration of distributed generation (DG), the conventional under-frequency load shedding (UFLS) face many challenges and may not perform as expected. This article proposes new UFLS schemes, which are designed to overcome the shortcomings of traditional load shedding scheme. These sche......With high penetration of distributed generation (DG), the conventional under-frequency load shedding (UFLS) face many challenges and may not perform as expected. This article proposes new UFLS schemes, which are designed to overcome the shortcomings of traditional load shedding scheme....... These schemes utilize directional relays, power flow through feeders, wind and PV measurements to optimally select the feeders to be disconnected during load shedding such that DG disconnection is minimized while disconnecting required amount of consumption. These different UFLS schemes are compared in terms...

  5. High power s-band vacuum load

    Energy Technology Data Exchange (ETDEWEB)

    Neubauer, Michael [Muons, Inc., Batavia, IL (United States); Dudas, Alan [Muons, Inc., Batavia, IL (United States); Krasnykh, Anatoly [SLAC National Accelerator Lab., Menlo Park, CA (United States)

    2016-12-29

    Through a combination of experimentation and calculation the components of a novel room temperature dry load were successfully fabricated. These components included lossy ceramic cylinders of various lengths, thicknesses, and percent of silicon carbide (SiC). The cylinders were then assembled into stainless steel compression rings by differential heating of the parts and a special fixture. Post machining of this assembly provided a means for a final weld. The ring assemblies were then measured for S-parameters, individually and in pairs using a low-cost TE10 rectangular to TE01 circular waveguide adapter specially designed to be part of the final load assembly. Matched pairs of rings were measured for assembly into the final load, and a sliding short designed and fabricated to assist in determining the desired short location in the final assembly. The plan for the project was for Muons, Inc. to produce prototype loads for long-term testing at SLAC. The STTR funds for SLAC were to upgrade and operate their test station to ensure that the loads would satisfy their requirements. Phase III was to be the sale to SLAC of loads that Muons, Inc. would manufacture. However, an alternate solution that involved a rebuild of the old loads, reduced SLAC budget projections, and a relaxed time for the replacement of all loads meant that in-house labor will be used to do the upgrade without the need for the loads developed in this project. Consequently, the project was terminated before the long term testing was initiated. However, SLAC can use the upgraded test stand to compare the long-term performance of the ones produced in this project with their rebuilt loads when they are available.

  6. Quantifying Training Loads in Contemporary Dance.

    Science.gov (United States)

    Jeffries, Annie C; Wallace, Lee; Coutts, Aaron J

    2017-07-01

    To describe the training demands of contemporary dance and determine the validity of using the session rating of perceived exertion (sRPE) to monitor exercise intensity and training load in this activity. In addition, the authors examined the contribution of training (ie, accelerometry and heart rate) and non-training-related factors (ie, sleep and wellness) to perceived exertion during dance training. Training load and ActiGraphy for 16 elite amateur contemporary dancers were collected during a 49-d period, using heart-rate monitors, accelerometry, and sRPE. Within-individual correlation analysis was used to determine relationships between sRPE and several other measures of training intensity and load. Stepwise multiple regressions were used to determine a predictive equation to estimate sRPE during dance training. Average weekly training load was 4283 ± 2442 arbitrary units (AU), monotony 2.13 ± 0.92 AU, strain 10677 ± 9438 AU, and average weekly vector magnitude load 1809,707 ± 1015,402 AU. There were large to very large within-individual correlations between training-load sRPE and various other internal and external measures of intensity and load. The stepwise multiple-regression analysis also revealed that 49.7% of the adjusted variance in training-load sRPE was explained by peak heart rate, metabolic equivalents, soreness, motivation, and sleep quality (y = -4.637 + 13.817%HR peak + 0.316 METS + 0.100 soreness + 0.116 motivation - 0.204 sleep quality). The current findings demonstrate the validity of the sRPE method for quantifying training load in dance, that dancers undertake very high training loads, and a combination of training and nontraining factors contribute to perceived exertion in dance training.

  7. USING BENCH PRESS LOAD TO PREDICT UPPER BODY EXERCISE LOADS IN PHYSICALLY ACTIVE INDIVIDUALS

    Directory of Open Access Journals (Sweden)

    Del P. Wong

    2013-03-01

    Full Text Available This study investigated whether loads for assistance exercises of the upper body can be predicted from the loads of the bench press exercise. Twenty-nine physically active collegiate students (age: 22.6 ± 2.5; weight training experience: 2.9 ± 2.1 years; estimated 1RM bench press: 54.31 ± 14.60 kg; 1RM: body weight ratio: 0.80 ± 0.22; BMI: 22.7 ± 2.1 kg·m-2 were recruited. The 6RM loads for bench press, barbell bicep curl, overhead dumbbell triceps extension, hammer curl and dumbbell shoulder press were measured. Test-retest reliability for the 5 exercises as determined by Pearson product moment correlation coefficient was very high to nearly perfect (0.82-0.98, p < 0.01. The bench press load was significantly correlated with the loads of the 4 assistance exercises (r ranged from 0.80 to 0.93, p < 0.01. Linear regression revealed that the bench press load was a significant (R2 range from 0.64 to 0.86, p < 0.01 predictor for the loads of the 4 assistance exercises. The following 6RM prediction equations were determined: (a Hammer curl = Bench press load (0.28 + 6.30 kg, (b Barbell biceps curl = Bench press load (0.33 + 6.20 kg, (c Overhead triceps extension = Bench press load (0.33 - 0.60 kg, and (d Dumbbell shoulder press = Bench press load (0.42 + 5.84 kg. The difference between the actual load and the predicted load using the four equations ranged between 6.52% and 8.54%, such difference was not significant. Fitness professionals can use the 6RM bench press load as a time effective and accurate method to predict training loads for upper body assistance exercises.

  8. Variability in Heat Strain in Fully Encapsulated Impermeable Suits in Different Climates and at Different Work Loads.

    Science.gov (United States)

    DenHartog, Emiel A; Rubenstein, Candace D; Deaton, A Shawn; Bogerd, Cornelis Peter

    2017-03-01

    A major concern for responders to hazardous materials (HazMat) incidents is the heat strain that is caused by fully encapsulated impermeable (NFPA 1991) suits. In a research project, funded by the US Department of Defense, the thermal strain experienced when wearing these suits was studied. Forty human subjects between the ages of 25 and 50 participated in a protocol approved by the local ethical committee. Six different fully encapsulated impermeable HazMat suits were evaluated in three climates: moderate (24°C, 50% RH, 20°C WBGT), warm-wet (32°C, 60% RH, 30°C WBGT), and hot-dry (45°C, 20% RH, 37°C WBGT, 200 W m-2 radiant load) and at three walking speeds: 2.5, 4, and 5.5 km h-1. The medium speed, 4 km h-1, was tested in all three climates and the other two walking speeds were only tested in the moderate climate. Prior to the test a submaximal exercise test in normal clothing was performed to determine a relationship between heart rate and oxygen consumption (pretest). In total, 163 exposures were measured. Tolerance time ranged from as low as 20 min in the hot-dry condition to 60 min (the maximum) in the moderate climate, especially common at the lowest walking speed. Between the six difference suits limited differences were found, a two-layered aluminized suit exhibited significant shorter tolerance times in the moderate climate, but no other major significant differences were found for the other climates or workloads. An important characteristic of the overall dataset is the large variability between the subjects. Although the average responses seem suitable to be predicted, the variability in the warmer strain conditions ranged from 20 min up to 60 min. The work load in these encapsulated impermeable suits was also significantly higher than working in normal clothing and higher than predicted by the Pandolf equation. Heart rate showed a very strong correlation to body core temperature and was in many cases the limiting factor. Setting the heart rate

  9. Using bench press load to predict upper body exercise loads in physically active individuals.

    Science.gov (United States)

    Wong, Del P; Ngo, Kwan-Lung; Tse, Michael A; Smith, Andrew W

    2013-01-01

    This study investigated whether loads for assistance exercises of the upper body can be predicted from the loads of the bench press exercise. Twenty-nine physically active collegiate students (age: 22.6 ± 2.5; weight training experience: 2.9 ± 2.1 years; estimated 1RM bench press: 54.31 ± 14.60 kg; 1RM: body weight ratio: 0.80 ± 0.22; BMI: 22.7 ± 2.1 kg·m(-2)) were recruited. The 6RM loads for bench press, barbell bicep curl, overhead dumbbell triceps extension, hammer curl and dumbbell shoulder press were measured. Test-retest reliability for the 5 exercises as determined by Pearson product moment correlation coefficient was very high to nearly perfect (0.82-0.98, p press load was significantly correlated with the loads of the 4 assistance exercises (r ranged from 0.80 to 0.93, p press load was a significant (R(2) range from 0.64 to 0.86, p press load (0.28) + 6.30 kg, (b) Barbell biceps curl = Bench press load (0.33) + 6.20 kg, (c) Overhead triceps extension = Bench press load (0.33) - 0.60 kg, and (d) Dumbbell shoulder press = Bench press load (0.42) + 5.84 kg. The difference between the actual load and the predicted load using the four equations ranged between 6.52% and 8.54%, such difference was not significant. Fitness professionals can use the 6RM bench press load as a time effective and accurate method to predict training loads for upper body assistance exercises. Key pointsThe bench press load was significantly correlated with the loads of the 4 assistance exercises.No significant differences were found between the actual load and the predicted load in the four equations.6RM bench press load can be a time effective and accurate method to predict training loads for upper body assistance exercises.

  10. Heat Load Estimator for Smoothing Pulsed Heat Loads on Supercritical Helium Loops

    Science.gov (United States)

    Hoa, C.; Lagier, B.; Rousset, B.; Bonnay, P.; Michel, F.

    Superconducting magnets for fusion are subjected to large variations of heat loads due to cycling operation of tokamaks. The cryogenic system shall operate smoothly to extract the pulsed heat loads by circulating supercritical helium into the coils and structures. However the value of the total heat loads and its temporal variation are not known before the plasma scenario starts. A real-time heat load estimator is of interest for the process control of the cryogenic system in order to anticipate the arrival of pulsed heat loads to the refrigerator and finally to optimize the operation of the cryogenic system. The large variation of the thermal loads affects the physical parameters of the supercritical helium loop (pressure, temperature, mass flow) so those signals can be used for calculating instantaneously the loads deposited into the loop. The methodology and algorithm are addressed in the article for estimating the heat load deposition before it reaches the refrigerator. The CEA patented process control has been implemented in a Programmable Logic Controller (PLC) and has been successfully validated on the HELIOS test facility at CEA Grenoble. This heat load estimator is complementary to pulsed load smoothing strategies providing an estimation of the optimized refrigeration power. It can also effectively improve the process control during the transient between different operating modes by adjusting the refrigeration power to the need. This way, the heat load estimator participates to the safe operation of the cryogenic system.

  11. Effect of Internal Clearance on Load Distribution and Life of Radially Loaded Ball and Roller Bearings

    Science.gov (United States)

    Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V.

    2012-01-01

    The effect of internal clearance on radially loaded deepgroove ball and cylindrical roller bearing load distribution and fatigue life was determined for four clearance groups defined in the bearing standards. The analysis was extended to negative clearance (interference) conditions to produce a curve of life factor versus internal clearance. Rolling-element loads can be optimized and bearing life maximized for a small negative operating clearance. Life declines gradually with positive clearance and rapidly with increasing negative clearance. Relationships were found between bearing life and internal clearance as a function of ball or roller diameter, adjusted for load. Results are presented as life factors for radially loaded bearings independent of bearing size or applied load. In addition, a modified Stribeck Equation is presented that relates the maximum rolling-element load to internal bearing clearance.

  12. Probabilistic model of bridge vehicle loads in port area based on in-situ load testing

    Science.gov (United States)

    Deng, Ming; Wang, Lei; Zhang, Jianren; Wang, Rei; Yan, Yanhong

    2017-11-01

    Vehicle load is an important factor affecting the safety and usability of bridges. An statistical analysis is carried out in this paper to investigate the vehicle load data of Tianjin Haibin highway in Tianjin port of China, which are collected by the Weigh-in- Motion (WIM) system. Following this, the effect of the vehicle load on test bridge is calculated, and then compared with the calculation result according to HL-93(AASHTO LRFD). Results show that the overall vehicle load follows a distribution with a weighted sum of four normal distributions. The maximum vehicle load during the design reference period follows a type I extremum distribution. The vehicle load effect also follows a weighted sum of four normal distributions, and the standard value of the vehicle load is recommended as 1.8 times that of the calculated value according to HL-93.

  13. The Statistical Properties of Host Load

    Directory of Open Access Journals (Sweden)

    Peter A. Dinda

    1999-01-01

    Full Text Available Understanding how host load changes over time is instrumental in predicting the execution time of tasks or jobs, such as in dynamic load balancing and distributed soft real‐time systems. To improve this understanding, we collected week‐long, 1 Hz resolution traces of the Digital Unix 5 second exponential load average on over 35 different machines including production and research cluster machines, compute servers, and desktop workstations. Separate sets of traces were collected at two different times of the year. The traces capture all of the dynamic load information available to user‐level programs on these machines. We present a detailed statistical analysis of these traces here, including summary statistics, distributions, and time series analysis results. Two significant new results are that load is self‐similar and that it displays epochal behavior. All of the traces exhibit a high degree of self‐similarity with Hurst parameters ranging from 0.73 to 0.99, strongly biased toward the top of that range. The traces also display epochal behavior in that the local frequency content of the load signal remains quite stable for long periods of time (150–450 s mean and changes abruptly at epoch boundaries. Despite these complex behaviors, we have found that relatively simple linear models are sufficient for short‐range host load prediction.

  14. Hood River Conservation Project load analysis

    Energy Technology Data Exchange (ETDEWEB)

    Stovall, T.K.

    1987-11-01

    As a part of the Hood River Conservation Project (HRCP), 314 homes were monitored to measure electrical energy use. The total electrical load, space heating load, water heating load (in about 200 homes), wood-stove heat output (in about 100 homes), and indoor temperature were monitored. Data were collected for one full year before and one full year after these homes were retrofit with conservation measures. Local weather information was also collected on a 15-min basis. This data base was used to evaluate the load savings attributable to HRCP. Two methods of weather normalization were used and showed close agreement. The weather-normalized diversified residential load savings on the Pacific Power and Light system and Hood River area peak days were >0.5 kW/household. The average spring, summer, and fall savings were much smaller, <0.1 kW/household. The load factor for the diversified residential load decreased following the conservation retrofit actions. 11 refs., 40 figs., 13 tabs.

  15. Electricity Crisis and Load Management in Bangladesh

    Directory of Open Access Journals (Sweden)

    Rajib Kanti Das

    2012-09-01

    Full Text Available Bangladesh is a densely populated country. Only a small part of her area is electrified which cover around 18% of total population. The people who are in the electrified area are suffering from severe load shedding. A systematic load management procedure related to demand side may improve the situation is the research problem. The major objectives serve by the research are to analyze contemporary electricity status with a view to drawing inference about demand supply gap and extracting benefits from load management. Data supplied by the Bangladesh Power Development Board, World Bank and outcome of survey are analyzed with some simple statistical tools to test the hypothesis. Analysis discloses that with properly managed uses of electricity with load switch and rotation week-end can improve the concurrent condition of electricity. Moreover, introducing smart distribution system, reducing system loss, shifting load to off-peak, large scale use of prepaid mete, observing energy week and using energy efficient home and office appliance are recommended to improve load through demand side management. Some other recommendations such as introducing alternative energy, public private partnership and using renewable energy development and producing energy locally are made for load management from the supply side.

  16. Factor structure underlying components of allostatic load.

    Directory of Open Access Journals (Sweden)

    Jeanne M McCaffery

    Full Text Available Allostatic load is a commonly used metric of health risk based on the hypothesis that recurrent exposure to environmental demands (e.g., stress engenders a progressive dysregulation of multiple physiological systems. Prominent indicators of response to environmental challenges, such as stress-related hormones, sympatho-vagal balance, or inflammatory cytokines, comprise primary allostatic mediators. Secondary mediators reflect ensuing biological alterations that accumulate over time and confer risk for clinical disease but overlap substantially with a second metric of health risk, the metabolic syndrome. Whether allostatic load mediators covary and thus warrant treatment as a unitary construct remains to be established and, in particular, the relation of allostatic load parameters to the metabolic syndrome requires elucidation. Here, we employ confirmatory factor analysis to test: 1 whether a single common factor underlies variation in physiological systems associated with allostatic load; and 2 whether allostatic load parameters continue to load on a single common factor if a second factor representing the metabolic syndrome is also modeled. Participants were 645 adults from Allegheny County, PA (30-54 years old, 82% non-Hispanic white, 52% female who were free of confounding medications. Model fitting supported a single, second-order factor underlying variance in the allostatic load components available in this study (metabolic, inflammatory and vagal measures. Further, this common factor reflecting covariation among allostatic load components persisted when a latent factor representing metabolic syndrome facets was conjointly modeled. Overall, this study provides novel evidence that the modeled allostatic load components do share common variance as hypothesized. Moreover, the common variance suggests the existence of statistical coherence above and beyond that attributable to the metabolic syndrome.

  17. Standardized Loads Acting in Knee Implants

    Science.gov (United States)

    Bergmann, Georg; Bender, Alwina; Graichen, Friedmar; Dymke, Jörn; Rohlmann, Antonius; Trepczynski, Adam; Heller, Markus O.; Kutzner, Ines

    2014-01-01

    The loads acting in knee joints must be known for improving joint replacement, surgical procedures, physiotherapy, biomechanical computer simulations, and to advise patients with osteoarthritis or fractures about what activities to avoid. Such data would also allow verification of test standards for knee implants. This work analyzes data from 8 subjects with instrumented knee implants, which allowed measuring the contact forces and moments acting in the joint. The implants were powered inductively and the loads transmitted at radio frequency. The time courses of forces and moments during walking, stair climbing, and 6 more activities were averaged for subjects with I) average body weight and average load levels and II) high body weight and high load levels. During all investigated activities except jogging, the high force levels reached 3,372–4,218N. During slow jogging, they were up to 5,165N. The peak torque around the implant stem during walking was 10.5 Nm, which was higher than during all other activities including jogging. The transverse forces and the moments varied greatly between the subjects, especially during non-cyclic activities. The high load levels measured were mostly above those defined in the wear test ISO 14243. The loads defined in the ISO test standard should be adapted to the levels reported here. The new data will allow realistic investigations and improvements of joint replacement, surgical procedures for tendon repair, treatment of fractures, and others. Computer models of the load conditions in the lower extremities will become more realistic if the new data is used as a gold standard. However, due to the extreme individual variations of some load components, even the reported average load profiles can most likely not explain every failure of an implant or a surgical procedure. PMID:24465856

  18. Standardized loads acting in knee implants.

    Directory of Open Access Journals (Sweden)

    Georg Bergmann

    Full Text Available The loads acting in knee joints must be known for improving joint replacement, surgical procedures, physiotherapy, biomechanical computer simulations, and to advise patients with osteoarthritis or fractures about what activities to avoid. Such data would also allow verification of test standards for knee implants. This work analyzes data from 8 subjects with instrumented knee implants, which allowed measuring the contact forces and moments acting in the joint. The implants were powered inductively and the loads transmitted at radio frequency. The time courses of forces and moments during walking, stair climbing, and 6 more activities were averaged for subjects with I average body weight and average load levels and II high body weight and high load levels. During all investigated activities except jogging, the high force levels reached 3,372-4,218N. During slow jogging, they were up to 5,165N. The peak torque around the implant stem during walking was 10.5 Nm, which was higher than during all other activities including jogging. The transverse forces and the moments varied greatly between the subjects, especially during non-cyclic activities. The high load levels measured were mostly above those defined in the wear test ISO 14243. The loads defined in the ISO test standard should be adapted to the levels reported here. The new data will allow realistic investigations and improvements of joint replacement, surgical procedures for tendon repair, treatment of fractures, and others. Computer models of the load conditions in the lower extremities will become more realistic if the new data is used as a gold standard. However, due to the extreme individual variations of some load components, even the reported average load profiles can most likely not explain every failure of an implant or a surgical procedure.

  19. A combined loading system integrated with portable winch and polyethylene chutes for loading of timber products

    Directory of Open Access Journals (Sweden)

    H. Hulusi Acar

    2016-01-01

    Full Text Available Truck loading operation is an important task during timber production operations in forestry. In Turkey, approximately 50 million timbers/logs are being produced per year, and then they are loaded into the logging trucks. The timber/logs are transported over the forest roads with an average of one million roundtrips. However, the traditional loading methods using manpower are mostly performed while some part is done by using loading machines which can be very costly and risky. This study aims developing a combined loading system in which heavy logs are loaded into logging trucks by pulling them by a log-line powered by a portable crane within the chute system. The slope of the log-line from ground to logging truck varied between 1% and 25%. Within the each work cycle of loading operation, only one log was loaded by pulling with portable crane. The average loading time was found as 161.8 seconds per cycle, in which 67% of the time was spent on pulling the log into the logging truck. The results indicated that the average pulling speed with crane power was 840.4 m/hr and productivity was calculated as 4.94 m3/hr. The result on system speed and productivity indicated close relations with results from previous studies. The hydraulic grapple loader or cranes are widely used and common loading machines, but they cannot be efficiently used in forestry operations, especially ones having a low timber productivity rate or having low economic value timber. In these conditions, loading methods that are cost efficient and do not require higher production rate should be employed. Therefore, a combined loading system introduced in this study can be a feasible solution for loading operations in those cases. Furthermore, it is believed that this loading system integrated with a portable crane can be cost efficient and time saving solution, as well as ergonomic and safe method in the field.

  20. Strength of concrete structures under dynamic loading

    Energy Technology Data Exchange (ETDEWEB)

    Kumpyak, O. G., E-mail: ogkumpyak@yandex.ru; Galyautdinov, Z. R., E-mail: gazr@yandex.ru; Kokorin, D. N., E-mail: kokorindenn@yandex.ru [Tomsk State University of Architecture and Building, 2, Solyanaya Sq., 634003, Tomsk (Russian Federation)

    2016-01-15

    The use of elastic supports is one the efficient methods of decreasing the dynamic loading. The paper describes the influence of elastic supports on the stress-strain state of steel concrete structures exposed to one-time dynamic loading resulting in failure. Oblique bending beams on elastic supports and their elastic, elastoplastic, and elastoplastic consolidation behavior are considered in this paper. For numerical calculations the developed computer program is used based on the finite element method. Research findings prove high efficiency of elastic supports under dynamic loading conditions. The most effective behavior of elastic supports is demonstrated at the elastoplastic stage. A good agreement is observed between the theoretical and experimental results.

  1. Feasability Study of Electronic Load Sensing Concept

    DEFF Research Database (Denmark)

    Hansen, Michael Rygaard; Andersen, Torben O.; Pedersen, Henrik C.

    2006-01-01

    circuit axial piston pump. Emphasis is on performance robustness with respect to both variations in internal physical parameters of the pump as well as the type of application dependant load that the pump is expected to drive.The research reflect mechatronics as an integrated design process, while......Electronic load sensing (ELS) systems have long been expected to start replacing traditional (hydro-mechanical) load sensing (LS) systems, which today are the standard on most medium and high-end mobile hydraulic applications. The reason for this being the potentials that ELS brings relative...

  2. A Server for ARINC 615A Loading

    OpenAIRE

    Gustafsson, Markus

    2013-01-01

    The development of the next generation of Saab's multirole combat aircraft the JAS 39 Gripen includes developing a lot of new software for the aircraft's on-board computers. The new software has to be loaded into these computers routinely, in order to carry out testing on it. This is currently a slow and tedious process. In order to load the computers a protocol defined in the ARINC 615A standard is used. Today Saab uses commercial software applications implementing this protocol for the load...

  3. Numerical Analyses of Plate Loading Test

    Directory of Open Access Journals (Sweden)

    Ionuţ-Ovidiu Toma

    2009-01-01

    Full Text Available A numerical simulation of plate loading test, in order to underlines the size effect on settlements and derived values of geotechnical parameters, is shown. The study is based on the comparison between the results obtained by Finite Element Method (FEM using the Mohr-Coulomb soil model and by some observations from literature. The obtained numerical results revealed that the subgrade reaction coefficient is strictly dependent on parameters like size of the loaded area and loading magnitude, and thus completely general and generic, and not a fundamental material property of soil that can somehow be determined rationally, as often one claims to be.

  4. Synthesis of polyoxometalate-loaded epoxy composites

    Science.gov (United States)

    Anderson, Benjamin J

    2014-10-07

    The synthesis of a polyoxometalate-loaded epoxy uses a one-step cure by applying an external stimulus to release the acid from the polyoxometalate and thereby catalyze the cure reaction of the epoxy resin. Such polyoxometalate-loaded epoxy composites afford the cured epoxy unique properties imparted by the intrinsic properties of the polyoxometalate. For example, polyoxometalate-loaded epoxy composites can be used as corrosion resistant epoxy coatings, for encapsulation of electronics with improved dielectric properties, and for structural applications with improved mechanical properties.

  5. Wind turbine blade testing under combined loading

    DEFF Research Database (Denmark)

    Roczek-Sieradzan, Agnieszka; Nielsen, Magda; Branner, Kim

    2011-01-01

    The paper presents full-scale blade tests under a combined flap- and edgewise loading. The main aim of this paper is to present the results from testing a wind turbine blade under such conditions and to study the structural behavior of the blade subjected to combined loading. A loading method using...... anchor plates was applied, allowing transverse shear distortion. The global and local deformation of the blade as well as the reproducibility of the test was studied and the results from the investigations are presented....

  6. Integrating Autonomous Load Controllers in Power Systems

    DEFF Research Database (Denmark)

    Douglass, Philip James

    and reliability constraints in power systems are motivating research into new control architectures suitable for such a large and complex system. The focus of this thesis is on an intermediate stage of evolution between today's largely passive loads and a future "Internet of Things". Specifically...... to the fluctuating production. The large number and geographic dispersion of loads make coordinating their behavior challenging. New telecommunication technology has reduced the cost of linking devices, promising a future "Internet of Things" where loads are fully networked. Strict real-time constraints...

  7. Modelling and Simulation of Wave Loads

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Thoft-Christensen, Palle

    A simple model of the wave load on slender members of offshore structures is described. The wave elevation of the sea state is modelled by a stationary Gaussian process. A new procedure to simulate realizations of the wave loads is developed. The simulation method assumes that the wave particle...... velocity can be approximated by a Gaussian Markov process. Known approximate results for the first-passage density or equivalently, the distribution of the extremes of wave loads are presented and compared with rather precise simulation results. It is demonstrated that the approximate results...

  8. Load control system. [for space shuttle external tank ground tests

    Science.gov (United States)

    Grosse, J. C.

    1977-01-01

    The load control system developed for the shuttle external structural tests is described. The system consists of a load programming/display module, and a load control module along with the following hydraulic system components: servo valves, dump valves, hydraulic system components, and servo valve manifold blocks. One load programming/display subsystem can support multiple load control subsystem modules.

  9. 46 CFR 196.40-15 - Load line marks.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Load line marks. 196.40-15 Section 196.40-15 Shipping... Markings on Vessels § 196.40-15 Load line marks. (a) Vessels assigned a load line shall have the deck line and the load line marks permanently marked or embossed as required by Subchapter E (Load Lines) of...

  10. Success of immediate loading implants compared to conventionally-loaded implants: a literature review.

    Science.gov (United States)

    Al-Sawai, Abdul-Aziz; Labib, Hussein

    2016-08-01

    The purpose of this systematic literature review was to compare the clinical performance between conventionally- (delayed) and immediately-loaded implants. A literature search of studies published between 1995 and 2012 was performed using several electronic databases and the following key words: "immediate loading", "dental implants", "immediate function", "early loading", "oral implants", "immediate restoration", and "systematic review" was performed. The electronic search was supplemented with hand-searching in dental journals and cross-referencing within the selected articles. Studies were considered for inclusion if they analyzed the success of the immediate loading protocol for implants, with emphasis given to randomized, controlled clinical trials. Among the clinical studies extracted from the literature, 120 studies met the inclusion criteria and were included in this systematic review. These studies included trials that involved yielded consistent results of success rates of immediately-loaded implants comparable to those known from conventionally-loaded implants, which were subjected to the immediate loading protocol or other loading protocols. According to the findings, there is evidence to suggest that immediate loading protocols demonstrate high implant survival rates and could be cautiously recommended for certain clinical situations. However, studies with a high level of evidence, especially randomized, controlled trials, performed over a longer timeframe are required to show a clear benefit over conventional and other loading types. © 2015 Wiley Publishing Asia Pty Ltd.

  11. Evaluation of Muscle Mechanical Capacities through the Two-load Method: Optimization of the Load Selection.

    Science.gov (United States)

    Pérez-Castilla, Alejandro; Jaric, Slobodan; Feriche, Belén; Padial, Paulino; García-Ramos, Amador

    2017-04-25

    Recent research has revealed that the force-velocity relationship obtained from the 'two-load method' (i.e., functional movements tested against just 2 external loads) could be a feasible method for the selective assessment of muscle force, velocity, and power-producing capacities. The study investigated the reliability and concurrent validity of the outcomes of the two-load method observed from (1) farther vs. closer data points (20-70%1RM, 30-60%1RM, and 40-50%1RM), and (2) force-biased (50-70%1RM) vs. velocity-biased (20-40%1RM) data points. Twenty-two men were tested on a ballistic bench press throw performed against 6 incremental loads ranging from 20% to 70% of the bench press one-repetition maximum (1RM). The two-load methods were constructed based on pairs of individually selected external loads and compared with the outcome of the force-velocity regression method applied to all 6 loads. The reliability and validity of the force-velocity relationship parameters decreased with the proximity of the data points (40-50%1RM loads (i.e., lighter and heavier loads, respectively) revealed a similar, but relatively moderate reliability and validity. Overall, the farthest pair of loads (i.e., 20%1RM and 70%1RM) revealed the highest reliability (CV = 5.5%, ICC = 0.89) and validity (r = 0.98) among all the two-load methods evaluated. These results demonstrate that the 20-70%1RM two-load method could be a feasible approach for testing individual muscle mechanical capacities, while the observed outcomes could be the most reliable and valid when obtained from the farthest pairs of applied loads.

  12. multilevel buck converter for automotive electrical load

    African Journals Online (AJOL)

    user

    MULTILEVEL BUCK CONVERTER FOR AUTOMOTIVE ELECTRICAL LOAD. E. T. Yabefa1,* and D. Ebregbe2. 1ELECTRICAL DEPARTMENT, BAYELSA STATE COLLEGE OF ARTS & SCIENCE (BYCAS) YENAGOA, BAYELSA STATE NIGERIA. 2ELECTRICAL ENGINEERING DEPARTMENT, NIGER DELTA UNIVERSITY, ...

  13. Handball load and shoulder injury rate

    DEFF Research Database (Denmark)

    Møller, M; Nielsen, R O; Attermann, J

    2017-01-01

    by scapular control, isometric shoulder strength or glenohumeral range of motion (ROM). Methods 679 players (14-18 years) provided weekly reports on shoulder injury and handball load (training and competition hours) over 31 weeks using the SMS, phone and medical examination system. Handball load in a given......Background Knowledge of injury patterns, an essential step towards injury prevention, is lacking in youth handball. Aim To investigate if an increase in handball load is associated with increased shoulder injury rates compared with a minor increase or decrease, and if an association is influenced...... week was categorised into (1) 60% relative to the weekly average amount of handball load the preceding 4 weeks. Assessment of shoulder isometric rotational and abduction strength, ROM and scapular control...

  14. Weapons Load Crew Management Program Update

    National Research Council Canada - National Science Library

    Richardson, Allan

    1997-01-01

    .... Widely used throughout the Air Force (including Air National Guard and Reserve units), WLCMP is a efficient way of managing load crew training, eliminating much of the time and manpower that is required by manual tracking procedures...

  15. Development of Engine Loads Methodology Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR seeks to improve the definition of design loads for rocket engine components such that higher performing, lighter weight engines can be developed more...

  16. Introduction to Single Piles under Lateral Loading

    DEFF Research Database (Denmark)

    Augustesen, Anders; Ibsen, Lars Bo

    The purpose of this chapter is to give a short introduction to single piles subjected to lateral loading. First, the observed behaviour of laterally loaded piles is described, i.e. the effects of loading conditions, installation procedure, pile type etc. on pile behaviour are presented (section 1.......2). The description is based on results of laboratory tests, full-scale field tests as well as numerical investigations presented in literature. Second, general methods that attempt to model lateral pile response are discussed in section 1.4. Third, focus is paid to a widely used method for prediction of the response...... of a lateral loaded pile, namely the Winkler approach in which the pile is modelled as an elastic beam on an elastic foundation (section 1.5). The soil response and thereby the elastic foundation is represented by springs with nonlinear behaviour (p-y curves). In section 1.6 different types and formulations...

  17. Exercise Load Measurement Insole (ELMI) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Exercise Load Measurement Insole (ELMI) is a system that is designed to measure normal and shear foot forces during exercise. The ELMI system is lightweight,...

  18. Load balancing multimodule switching power converters

    Science.gov (United States)

    Mclyman, W. T.; Wester, G. W.

    1979-01-01

    Regulating system individually adjusts duty cycles of modules so that all share load equally, thus, protects individual modules and their components from overload and increases reliability and life expectancy. Converters are alternative to high-power, single unit systems.

  19. Final Project Report Load Modeling Transmission Research

    Energy Technology Data Exchange (ETDEWEB)

    Lesieutre, Bernard [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Bravo, Richard [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Yinger, Robert [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Chassin, Dave [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Huang, Henry [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Lu, Ning [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Hiskens, Ian [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Venkataramanan, Giri [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2012-03-31

    The research presented in this report primarily focuses on improving power system load models to better represent their impact on system behavior. The previous standard load model fails to capture the delayed voltage recovery events that are observed in the Southwest and elsewhere. These events are attributed to stalled air conditioner units after a fault. To gain a better understanding of their role in these events and to guide modeling efforts, typical air conditioner units were testing in laboratories. Using data obtained from these extensive tests, new load models were developed to match air conditioner behavior. An air conditioner model is incorporated in the new WECC composite load model. These models are used in dynamic studies of the West and can impact power transfer limits for California. Unit-level and systemlevel solutions are proposed as potential solutions to the delayed voltage recovery problem.

  20. Quantum load balancing in ad hoc networks

    Science.gov (United States)

    Hasanpour, M.; Shariat, S.; Barnaghi, P.; Hoseinitabatabaei, S. A.; Vahid, S.; Tafazolli, R.

    2017-06-01

    This paper presents a novel approach in targeting load balancing in ad hoc networks utilizing the properties of quantum game theory. This approach benefits from the instantaneous and information-less capability of entangled particles to synchronize the load balancing strategies in ad hoc networks. The quantum load balancing (QLB) algorithm proposed by this work is implemented on top of OLSR as the baseline routing protocol; its performance is analyzed against the baseline OLSR, and considerable gain is reported regarding some of the main QoS metrics such as delay and jitter. Furthermore, it is shown that QLB algorithm supports a solid stability gain in terms of throughput which stands a proof of concept for the load balancing properties of the proposed theory.

  1. Predicting reinforced concrete response to blast loads

    National Research Council Canada - National Science Library

    Jacques, Eric; Lloyd, Alan; Saatcioglu, Murat

    2013-01-01

    .... The results are presented in graphical format in terms of structural load-deformation characteristics, single degree of freedom displacement--time histories and iso-displacement pressure-impulse diagrams...

  2. Multifrequency Printed Antennas Loaded with Metamaterial Particles

    Directory of Open Access Journals (Sweden)

    D. Segovia-Vargas

    2009-06-01

    Full Text Available This paper provides a review of printed antennas loaded with metamaterial particles. This novel technique allows developing printed antennas with interesting features such as multifrequency (simultaneous operation over two or more frequency bands and multifunctionality (e. g. radiation pattern diversity. Moreover, compactness is also achieved and the main advantages of conventional printed antennas (light weight, low profile, low cost ... are maintained. Different types of metamaterial-loaded printed antennas are reviewed: printed dipoles and patch antennas. Several prototypes are designed, manufactured and measured showing good results. Furthermore, simple but accurate equivalent models are proposed. These models allow an easy and quick design of metamaterial-loaded printed antennas. Finally, two interesting applications based on the proposed antennas are reviewed: the patch antennas are used as radiating elements of emerging active RFID systems in the microwave band and the metamaterial-loaded printed dipoles are employed to increase the performance of log-periodic arrays.

  3. Home Appliance Load Scheduling with SEMIAH

    DEFF Research Database (Denmark)

    Jacobsen, Rune Hylsberg; Ghasem Azar, Armin; Zhang, Qi

    2015-01-01

    The European research project SEMIAH aims at designing a scalable infrastructure for residential demand response. This paper presents the progress towards a centralized load scheduling algorithm for controlling home appliances taking power grid constraints and satisfaction of consumers into account....

  4. LIGHT-WEIGHT LOAD-BEARING STRUCTURE

    DEFF Research Database (Denmark)

    2009-01-01

    The invention relates to a light-weight load-bearing structure (1) with optimized compression zone (2), where along one or more compression zones (2) in the structure (1) to be cast a core (3) of strong concrete is provided, which core (3) is surrounded by concrete of less strength (4) compared...... to the core (3) of strong concrete. The invention also relates to a method of casting of light-weight load-bearing structures (1) with optimized compression zone (2) where one or more channels, grooves, ducts, pipes and/or hoses (5) formed in the load-bearing structure (1) serves as moulds for moulding one...... or more cores (3) of strong concrete in the light-weight load-bearing structure (1)....

  5. Radiopure Metal-Loaded Liquid Scintillator

    Energy Technology Data Exchange (ETDEWEB)

    Rosero, Richard [Brookhaven National Lab. (BNL), Upton, NY (United States). Chemistry Dept.; Yeh, Minfang [Brookhaven National Lab. (BNL), Upton, NY (United States). Chemistry Dept.

    2015-03-18

    Metal-loaded liquid scintillator plays a key role in particle and nuclear physics experiments. The applications of metal ions in various neutrino experiments and the purification methods for different scintillator components are discussed in this paper.

  6. Loaded Gelled Bipropellants for Optimized Performance Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The focus of this program is the development and validation of formulations, and development methodologies, for optimizing high-performance particulate-loaded...

  7. Heat loads in hypersonic vehicle design

    Energy Technology Data Exchange (ETDEWEB)

    Hirschel, E.H. [Daimler-Benz Aerospace AG, Muenchen (Germany)

    1999-12-01

    Heat loads are the major issue in high-speed vehicle design. Heat loads prediction capabilities need to be improved with regard to the materials and structure concept, and the aerodynamic and propulsion performance. Surface radiation cooling is the basic means to reduce heat loads on high-speed vehicles. Strong couplings can exist with the aerodynamic performance of vehicles, the structure and materials design, and flow-physics and thermochemical phenomena. Qualitative knowledge is available to interpret (computation) results and flight data, and to give the designer insight into related disciplinary and interdisciplinary vehicle design problems. Flow-physics and thermo-chemical models in prediction tools are inadequate. Heat loads and the related surface-temperature effects pose very important and challenging research and development problems. (orig.)

  8. Design of sandwich beams for concentrated loading

    Science.gov (United States)

    Kim, Jongman

    Although sandwich construction offers well-known advantages for high stiffness with light-weight, the problem of designing a sandwich structure to withstand localized loading such as might result from accidental impact, for example, is important. The review of the literature and experimental results performed by the author has shown that current design and analysis procedures are not suitable for predictions of the response of sandwich structures for concentrated loading. To investigate the response of sandwich structures to concentrated loading, experiments were carried out on beam specimens with polyurethane foam core with various densities and thickness, and faces made of AS4/3501-6 carbon/epoxy fiber composite of various thickness under three point loading, which gives a concentrated loading. Overall deformation was measured, along with strains from both surface and embedded gages. Additionally, compression tests and torsion tests have been done for the polyurethane foam used as core in the sandwich beam to characterize its yield properties. Many theories, including classical theory, first order shear deformation theory, higher order theory, elasticity and FE analysis, were compared with the three-point bending experiments. A two-dimensional elasticity solution, which is suitable for sandwich beams under simply support boundary conditions, was used to obtain the strain/stress distribution, failure prediction and optimization work. The common failure modes of sandwich beams have been observed, including core failure in compression and shear failure in core, delamination, and fiber failure in the face. The failure modes can be predicted for sandwich beams under localized loading using elasticity theory and the failure is controlled by a failure mode with the lowest load. An algorithm developed by Swanson and Kim was used to predict the optimum design of sandwich structures for strength to weight under concentrated loading and compared with experimental yield or

  9. LTE Load Balancing dengan Skenario Game Theory

    Directory of Open Access Journals (Sweden)

    Nila Putri Mardela

    2013-09-01

    Full Text Available Adanya multi user yang meminta untuk dilayani dengan baik dalam kondisi apapun terutama dalam kondisi cell yang congested tentunya menjadi hal yang sangat penting untuk diperhatikan dalam sistem komunikasi wireless termasuk dalam hal ini untuk teknologi Long Term Evolution (LTE sehingga diperlukan suatu proses dalam jaringan yang dapat menanggulangi permintaan user ini. Proses yang dapat dilakukan adalah dengan load balancing. Untuk memodelkan interaksi dari elemen jaringan yang melakukan load balancing , maka dibutuhkan suatu teknik atau skenario sehingga dicapai suatu keputusan yang rasional untuk dilakukannya load balancing. Teknik yang dapat digunakan adalah skenario game theory. Dalam tugas akhir yang berjudul LTE Load Balancing dengan Skenario Game Theory ini diusulkan metode Load Balancing Cooperative Game pada LTE dimana setiap tindakan yang dilakukan dalam rangka load balancing didasarkan terhadap nilai utilitas yang akan didapatkan, dan setiap eNB berhak memilih tindakan yang memiliki nilai utilitas maksimum. Efek dari load balancing yang diinginkan adalah penurunan jumlah drop call sebagai indikasi peningkatan layanan dan peningkatan utilitas eNB sebagai indikasi pengoptimalan utilitas bandwidth yang tidak terpakai. Dengan menerapkan LTE Load Balancing dengan Skenario Game Theory ini maka dapat dicapai penurunan jumlah drop call sebesar 92,33%, peningkatan utilitas eNB penolong sebesar 41,24%, dan 0,249% untuk peningkatan utilitas eNB congested yang meminta bantuan. Apabila dalam skema handover user dari eNB cell sumber yang congested ke eNB cell tetangga yang tidak congested ditambahkan syarat bahwa RSRP user dari eNB cell tetangga lebih besar dari pada eNB cell sumber maka penurunan drop call yang dicapai adalah sebesar 37,12%, peningkatan utilitas eNB penolong adalah sebesar 9,375%, dan peningkatan utilitas eNB congested yang meminta bantuan adalah sebesar 0,249%.

  10. Gearbox Reliability Collaborative (GRC) Description and Loading

    Energy Technology Data Exchange (ETDEWEB)

    Oyague, F.

    2011-11-01

    This document describes simulated turbine load cases in accordance to the IEC 61400-1 Ed.3 standard, which is representative of the typical wind turbine design process. The information presented herein is intended to provide a broad understanding of the gearbox reliability collaborative 750kW drivetrain and turbine configuration. In addition, fatigue and ultimate strength drivetrain loads resulting from simulations are presented. This information provides the bases for the analytical work of the gearbox reliability collaborative effort.

  11. Foot Marching, Load Carriage, and Injury Risk

    Science.gov (United States)

    2016-05-01

    Knapik, and J.J. 1994. Exercise, training and injuries. Sports Med 18(3): 202-1. 35. APHC (Prov) Blister Prevention Factsheet. 2015. Available at...1.5 Flashlight, other equipment 2 Approach Load Fighting Load + 32*pounds = 102* pounds Assault rucksack with attachments 9 Hydration bladder...Men 475,745) Source: Knapik J et al. Stress Fracture Risk Factors in Basic Combat Training, 2012. Int J Sports Med, 33: 940–946. Men n

  12. MCO loading and cask loadout technical manual

    Energy Technology Data Exchange (ETDEWEB)

    PRAGA, A.N.

    1998-10-01

    A compilation of the technical basis for loading a multi-canister overpack (MCO) with spent nuclear fuel and then placing the MCO into a cask for shipment to the Cold Vacuum Drying Facility. The technical basis includes a description of the process, process technology that forms the basis for loading alternatives, process control considerations, safety considerations, equipment description, and a brief facility structure description.

  13. ANTHROPOGENIC LOAD ON RIVERS OF URBAN AREAS

    OpenAIRE

    Kurochkina Valentina Aleksandrovna; Bogomolova Tat’yana Gennad’evna; Kirov Borislav Lyubomirov

    2016-01-01

    The increasing speed of urbanization and population growth lead to the increasing anthropogenic load on water bodies. The urbanization processes in Russia are more intensive than in other countries. The dense population and great industrial potential lead to the fact that the urbanized territories become the main sources of water pollution. That’s why the environmental control of the state of water objects is needed. In the article the authors study the problem of anthropogenic load impact on...

  14. Economic Load Dispatch Using Grey Wolf Optimization

    OpenAIRE

    Dr.Sudhir Sharma; Shivani Mehta

    2015-01-01

    This paper presents grey wolf optimization (GWO) to solve convex economic load dispatch (ELD) problem. Grey Wolf Optimization (GWO) is a new meta-heuristic inspired by grey wolves. The leadership hierarchy and hunting mechanism of the grey wolves is mimicked in GWO. The objective of ELD problem is to minimize the total generation cost while fulfilling the different constraints, when the required load of power system is being supplied. The proposed technique is implemented on two d...

  15. Mechanical Predictors of Discomfort during Load Carriage.

    Directory of Open Access Journals (Sweden)

    Patrick D Wettenschwiler

    Full Text Available Discomfort during load carriage is a major issue for activities using backpacks (e.g. infantry maneuvers, children carrying school supplies, or outdoor sports. It is currently unclear which mechanical parameters are responsible for subjectively perceived discomfort. The aim of this study was to identify objectively measured mechanical predictors of discomfort during load carriage. We compared twelve different configurations of a typical load carriage system, a commercially available backpack with a hip belt. The pressure distribution under the hip belt and the shoulder strap, as well as the tensile force in the strap and the relative motion of the backpack were measured. Multiple linear regression analyses were conducted to investigate possible predictors of discomfort. The results demonstrate that static peak pressure, or alternatively, static strap force is a significant (p<0.001 predictor of discomfort during load carriage in the shoulder and hip region, accounting for 85% or more of the variation in discomfort. As an additional finding, we discovered that the regression coefficients of these predictors are significantly smaller for the hip than for the shoulder region. As static peak pressure is measured directly on the body, it is less dependent on the type of load carriage system than static strap force. Therefore, static peak pressure is well suited as a generally applicable, objective mechanical parameter for the optimization of load carriage system design. Alternatively, when limited to load carriage systems of the type backpack with hip belt, static strap force is the most valuable predictor of discomfort. The regionally differing regression coefficients of both predictors imply that the hip region is significantly more tolerant than the shoulder region. In order to minimize discomfort, users should be encouraged to shift load from the shoulders to the hip region wherever possible, at the same time likely decreasing the risk of low

  16. Optimizing Preseason Training Loads in Australian Football.

    Science.gov (United States)

    Carey, David L; Crow, Justin; Ong, Kok-Leong; Blanch, Peter; Morris, Meg E; Dascombe, Ben J; Crossley, Kay M

    2018-02-14

    To investigate whether preseason training plans for Australian football can be computer generated using current training-load guidelines to optimize injury-risk reduction and performance improvement. A constrained optimization problem was defined for daily total and sprint distance, using the preseason schedule of an elite Australian football team as a template. Maximizing total training volume and maximizing Banister-model-projected performance were both considered optimization objectives. Cumulative workload and acute:chronic workload-ratio constraints were placed on training programs to reflect current guidelines on relative and absolute training loads for injury-risk reduction. Optimization software was then used to generate preseason training plans. The optimization framework was able to generate training plans that satisfied relative and absolute workload constraints. Increasing the off-season chronic training loads enabled the optimization algorithm to prescribe higher amounts of "safe" training and attain higher projected performance levels. Simulations showed that using a Banister-model objective led to plans that included a taper in training load prior to competition to minimize fatigue and maximize projected performance. In contrast, when the objective was to maximize total training volume, more frequent training was prescribed to accumulate as much load as possible. Feasible training plans that maximize projected performance and satisfy injury-risk constraints can be automatically generated by an optimization problem for Australian football. The optimization methods allow for individualized training-plan design and the ability to adapt to changing training objectives and different training-load metrics.

  17. Environmental stress, psychological stress and allostatic load.

    Science.gov (United States)

    Clark, Michael S; Bond, Malcolm J; Hecker, Jane R

    2007-01-01

    The mechanism by which chronic caregiving stress results in poor health is not well understood. The objective was to determine whether such a mechanism may be allostatic load, a novel concept specifying physiological systems that may suffer cumulative wear and tear following chronic stress, leading collectively to poor health. The study examines the association of allostatic load with environmental and psychological stress in the contexts of dementia caregiving and relinquishment of care, and is a 2-year longitudinal comparison of three groups: 80 new dementia spouse caregivers, 120 veteran caregivers, and 60 non-caregivers. Data comprised allostatic load markers and environmental and psychological stress measures. Cross-lagged analyses produced a statistically significant association between psychological stress and one allostatic load component (primary mediators). Psychological stress was a better predictor of primary mediators than environmental stress. Primary mediators rose with time for caregivers, but not for non-caregivers. A greater rise was evident for caregivers who had relinquished their role by the second year, although the level of psychological stress actually declined. Primary mediators are a key component of the relationship between allostatic load and prior stress. When allostatic load is treated as an outcome of stress, it is important to distinguish environmental and psychological stress.

  18. Characteristics of Braced Excavation under Asymmetrical Loads

    Directory of Open Access Journals (Sweden)

    Changjie Xu

    2013-01-01

    Full Text Available Numerous excavation practices have shown that large discrepancies exist between field monitoring data and calculated results when the conventional symmetry-plane method (with half-width is used to design the retaining structure under asymmetrical loads. To examine the characteristics of a retaining structure under asymmetrical loads, we use the finite element method (FEM to simulate the excavation process under four different groups of asymmetrical loads and create an integrated model to tackle this problem. The effects of strut stiffness and wall length are also investigated. The results of numerical analysis clearly imply that the deformation and bending moment of diaphragm walls are distinct on different sides, indicating the need for different rebar arrangements when the excavation is subjected to asymmetrical loads. This study provides a practical approach to designing excavations under asymmetrical loads. We analyze and compare the monitoring and calculation data at different excavation stages and find some general trends. Several guidelines on excavation design under asymmetrical loads are drawn.

  19. DNS load balancing in the CERN cloud

    Science.gov (United States)

    Reguero Naredo, Ignacio; Lobato Pardavila, Lorena

    2017-10-01

    Load Balancing is one of the technologies enabling deployment of large-scale applications on cloud resources. A DNS Load Balancer Daemon (LBD) has been developed at CERN as a cost-effective way to balance applications accepting DNS timing dynamics and not requiring persistence. It currently serves over 450 load-balanced aliases with two small VMs acting as master and slave. The aliases are mapped to DNS subdomains. These subdomains are managed with DDNS according to a load metric, which is collected from the alias member nodes with SNMP. During the last years, several improvements were brought to the software, for instance: support for IPv6, parallelization of the status requests, implementing the client in Python to allow for multiple aliases with differentiated states on the same machine or support for application state. The configuration of the Load Balancer is currently managed by a Puppet type. It discovers the alias member nodes and gets the alias definitions from the Ermis REST service. The Aiermis self-service GUI for the management of the LB aliases has been produced and is based on the Ermis service above that implements a form of Load Balancing as a Service (LBaaS). The Ermis REST API has authorisation based in Foreman hostgroups. The CERN DNS LBD is Open Software with Apache 2 license.

  20. Predicting Lifetime of a Thermomechanically Loaded Component

    Science.gov (United States)

    Murthy, Pappu L. N.; Gyekenyesi, John Z.; Mital, Subodh; Brewer, David N.

    2006-01-01

    NASALIFE is a computer program for predicting the lifetime, as affected by low cycle fatigue (LCF) and creep rupture, of a structural component subject to temporally varying, multiaxial thermomechanical loads. The component could be, for example, part of an aircraft turbine engine. Empirical data from LCF tests, creep rupture tests, and static tensile tests are used as references for predicting the number of missions the component can withstand under a given thermomechanical loading condition. The user prepares an input file containing the creep-rupture and cyclic-fatigue information, temperature-dependent material properties, and mission loading and control flags. The creep rupture information can be entered in tabular form as stress versus life or by means of parameters of the Larson-Miller equation. The program uses the Walker mean-stress model to adjust predicted life for ranges of the ratio between the maximum and minimum stresses. Data representing complex load cycles are reduced by the rainflow counting method. Miner's rule is utilized to combine the damage at different load levels. Finally, the program determines the total damage due to creep and combines it with the fatigue damage due to the cyclic loading and predicts the approximate number of missions a component can endure before failing.

  1. Mass loading effect of shock accelerometers

    Science.gov (United States)

    Wu, Lixue; Wong, George S. K.; Hanes, Peter; Ohm, Won-Suk

    2005-04-01

    Mass loading affects the sensitivity of an accelerometer. The mass loading effect can be corrected using mass loading correction curves published by manufacturers. These curves, however, are only applicable to the sinusoidal acceleration below 500 m/s2. The mass loading effect on the sensitivity of an Endevco 2270 accelerometer in shock calibration, from 500 m/s2 and up, was investigated using a laser vibrometer. A new method for conversion of a velocity signal to an acceleration signal was developed. With this method, the sensitivities of the above accelerometer for different mass loads at different shock levels were measured. The mass loading effect in shock calibration for this accelerometer was then obtained. The limitations of the sensitivity measurements were also studied. The variance of the measured sensitivity was mainly due to the resolution limitation (8-bit) of the A/D converter in the digital oscilloscope. A correlation matching algorithm was then developed that utilizes the similarity between the measured acceleration signal and that converted from the velocity signal to further improve the resolution of the digital oscilloscope.

  2. Fatigue life prediction under service load considering strengthening effect of loads below fatigue limit

    Science.gov (United States)

    Zhao, Lihui; Zheng, Songlin; Feng, Jinzhi

    2014-11-01

    Lightweight design requires an accurate life prediction for structures and components under service loading histories. However, predicted life with the existing methods seems too conservative in some cases, leading to a heavy structure. Because these methods are established on the basis that load cycles would only cause fatigue damage, ignore the strengthening effect of loads. Based on Palmgren-Miner Rule (PMR), this paper introduces a new method for fatigue life prediction under service loadings by taking into account the strengthening effect of loads below the fatigue limit. In this method, the service loadings are classified into three categories: damaging load, strengthening load and none-effect load, and the process for fatigue life prediction is divided into two stages: stage I and stage II, according to the best strengthening number of cycles. During stage I, fatigue damage is calculated considering both the strengthening and damaging effect of load cycles. While during stage II, only the damaging effect is considered. To validate this method, fatigue lives of automobile half shaft and torsion beam rear axle are calculated based on the new method and traditional methods, such as PMR and Modified Miner Rule (MMR), and fatigue tests of the two components are conducted under service loading histories. The tests results show that the percentage errors of the predicted life with the new method to mean life of tests for the two components are -3.78% and -1.76% separately, much lesser than that with PMR and MMR. By considering the strengthening effect of loads below the fatigue limit, the new method can significantly improve the accuracy for fatigue life prediction. Thus lightweight design can be fully realized in the design stage.

  3. Evaluation of load rejection to house load test at 50% power for UCN 3

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chang Gyun; Sohn, Suk Whun; Sohn, Jong Joo; Seo, Jong Tae; Lee, Sang Keun [KOPEC, Yongin (Korea, Republic of); Kim, Yong Sung; Nam, Kyu Won; Jung, Yang Mook; Chae, Kyeong Sik; Koh, Bum Jae; Oh, Chul Sung; Park, Hee Chool [KEPCO, Seoul (Korea, Republic of)

    1998-05-01

    The Load Rejection to House Load test at 50% power was successfully performed during the UCN 3 PAT period. In this test, all plant control systems automatically controlled the plant from 50% power to house load operation mode. The KISPAC code, which was used in the performance analysis during the design process of UCN 3 and 4, predictions of the test agreed with the measured data demonstrating the validity of the code as well as completeness of the plant design.

  4. Design and analysis of a novel mechanical loading machine for dynamic in vivo axial loading.

    Science.gov (United States)

    Macione, James; Nesbitt, Sterling; Pandit, Vaibhav; Kotha, Shiva

    2012-02-01

    This paper describes the construction of a loading machine for performing in vivo, dynamic mechanical loading of the rodent forearm. The loading machine utilizes a unique type of electromagnetic actuator with no mechanically resistive components (servotube), allowing highly accurate loads to be created. A regression analysis of the force created by the actuator with respect to the input voltage demonstrates high linear correlation (R(2) = 1). When the linear correlation is used to create dynamic loading waveforms in the frequency (0.5-10 Hz) and load (1-50 N) range used for in vivo loading, less than 1% normalized root mean square error (NRMSE) is computed. Larger NRMSE is found at increased frequencies, with 5%-8% occurring at 40 Hz, and reasons are discussed. Amplifiers (strain gauge, linear voltage displacement transducer (LVDT), and load cell) are constructed, calibrated, and integrated, to allow well-resolved dynamic measurements to be recorded at each program cycle. Each of the amplifiers uses an active filter with cutoff frequency at the maximum in vivo loading frequencies (50 Hz) so that electronic noise generated by the servo drive and actuator are reduced. The LVDT and load cell amplifiers allow evaluation of stress-strain relationships to determine if in vivo bone damage is occurring. The strain gauge amplifier allows dynamic force to strain calibrations to occur for animals of different sex, age, and strain. Unique features are integrated into the loading system, including a weightless mode, which allows the limbs of anesthetized animals to be quickly positioned and removed. Although the device is constructed for in vivo axial bone loading, it can be used within constraints, as a general measurement instrument in a laboratory setting.

  5. Mapping of Critical Loads and Critical Load Exceedances in the Killarney Provincial Park, Ontario, Canada

    OpenAIRE

    Hindar, A.; Henriksen, A.

    1998-01-01

    Calculations of critical loads for inputs of strong acids to lakes and exceedances of critical load can be a useful tool for the management of polluted areas. In Sudbury, Canada, large emissions of sulfur dioxide have resulted in widespread lake acidification in parts of northeastern Canada. Due to its vicinity to Sudbury, extensive lake acidification and fish loss has occurred in the Killarney Provincial Park. We have linked measured water quality to critical loads and strong acid deposition...

  6. The Optimal Choice of Promotional Vehicles: Front-Loaded or Rear-Loaded Incentives?

    OpenAIRE

    Z. John Zhang; Aradhna Krishna; Sanjay K. Dhar

    2000-01-01

    We examine the key factors that influence a firm's decision whether to use front-loaded or rear-loaded incentives. When using price packs, direct mail coupons, FSI coupons or peel-off coupons, consumers obtain an immediate benefit upon purchase or a front-loaded incentive. However, when buying products with in-pack coupons or products affiliated with loyalty programs, promotion incentives are obtained on the next purchase occasion or later, i.e., a rear-loaded incentive. Our analysis shows th...

  7. Static ice loads on hydro-electric structures: ice load monographs: Volume 1: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Comfort, G.; Abdelnour, R.; Gong, Y.; Dinovitzer, A.

    1996-07-01

    Ice loads on hydro-electric structures were measured during a four-year field program. Loads were measured at Hydro-Quebec`s Paugan dam, Ontario Hydro`s Arnprior and Otto Holden dams, and in a large outdoor basin at the National Research Council (NRC) during one winter. Ice loads were measured in the reservoir ice sheet, near the concrete face of the dam, and near the gate and pier of the Paugan dam. Ice stresses were measured continuously by stressmeters that were deployed in the ice. Loads at the Paugan dam and the NRC basin resulted mostly from ice temperature changes. The loads at the Arnprior and Otto Holden dams were produced by a combination of ice temperature and water level changes. The collected data was analyzed in detail and efforts were made to improve techniques for predicting ice loads. Significant progress was made towards the development of detailed, quantitative understanding of static ice loads on hydro-electric structures, and the factors controlling them. However, the ice load predictors are subject to a number of limitations and further work is required before changes to design practices can be recommended with confidence. More field data collection would also improve the definition of loads arising from a combination of water level and ice temperature changes. Additional numerical analyses was also recommended to better define the effects of ice confinement. Appendices were published separately in volume 2 of this report. 43 refs., 18 tabs., 96 figs.

  8. Application of PSAT to Load Flow Analysis with STATCOM under Load Increase Scenario and Line Contingencies

    Science.gov (United States)

    Telang, Aparna S.; Bedekar, P. P.

    2017-09-01

    Load flow analysis is the initial and essential step for any power system computation. It is required for choosing better options for power system expansion to meet with ever increasing load demand. Implementation of Flexible AC Transmission System (FACTS) device like STATCOM, in the load flow, which is having fast and very flexible control, is one of the important tasks for power system researchers. This paper presents a simple and systematic approach for steady state power flow calculations with FACTS controller, static synchronous compensator (STATCOM) using command line usage of MATLAB tool-power system analysis toolbox (PSAT). The complexity of MATLAB language programming increases due to incorporation of STATCOM in an existing Newton-Raphson load flow algorithm. Thus, the main contribution of this paper is to show how command line usage of user friendly MATLAB tool, PSAT, can extensively be used for quicker and wider interpretation of the results of load flow with STATCOM. The novelty of this paper lies in the method of applying the load increase pattern, where the active and reactive loads have been changed simultaneously at all the load buses under consideration for creating stressed conditions for load flow analysis with STATCOM. The performance have been evaluated on many standard IEEE test systems and the results for standard IEEE-30 bus system, IEEE-57 bus system, and IEEE-118 bus system are presented.

  9. 2006 Pacific Northwest Loads and Resources Study.

    Energy Technology Data Exchange (ETDEWEB)

    United States. Bonneville Power Administration.

    2006-03-01

    The Pacific Northwest Loads and Resources Study (White Book), which is published annually by the Bonneville Power Administration (BPA), establishes one of the planning bases for supplying electricity to customers. The White Book contains projections of regional and Federal system load and resource capabilities, along with relevant definitions and explanations. The White Book also contains information obtained from formalized resource planning reports and data submittals including those from individual utilities, the Northwest Power and Conservation Council (Council), and the Pacific Northwest Utilities Conference Committee (PNUCC). The White Book is not an operational planning guide, nor is it used for determining BPA revenues, although the database that generates the data for the White Book analysis contributes to the development of BPA's inventory and ratemaking processes. Operation of the Federal Columbia River Power System (FCRPS) is based on a set of criteria different from that used for resource planning decisions. Operational planning is dependent upon real-time or near-term knowledge of system conditions that include expectations of river flows and runoff, market opportunities, availability of reservoir storage, energy exchanges, and other factors affecting the dynamics of operating a power system. The load resource balance of both the Federal system and the region is determined by comparing resource availability to an expected level of total retail electricity consumption. Resources include projected energy capability plus contract purchases. Loads include a forecast of retail obligations plus contract obligations. Surplus energy is available when resources are greater than loads. This surplus energy could be marketed to increase revenues. Energy deficits occur when resources are less than loads. These energy deficits will be met by any combination of the following: better-than-critical water conditions, demand-side management and conservation

  10. Multilayered elastic analysis formulation for surface moment loading

    CSIR Research Space (South Africa)

    Maina, JW

    2006-01-01

    Full Text Available into consideration surface moment loading. GOVERNING EQUATIONS The governing equations may be presented by using cylindrical coordinate system and assume that a circular load, with radius a , is acting on the pavement surface and the magnitude of the load varies... of Equation (1a) is the uniformly distributed vertical load, while the second item represents the load, which is anti-symmetric about the y - axis. The loading distribution obtained from Equation (1a) is a sum of uniformly distributed load and the load...

  11. Laterally cyclic loading of monopile in dense sand

    DEFF Research Database (Denmark)

    Klinkvort, Rasmus Tofte; Hededal, Ole; Svensson, M.

    2011-01-01

    the loading conditions. In these tests the load conditions are controlled by two load characteristics, one controlling the level of the cyclic loading and one controlling the characteristic of the cyclic loading. The centrifuge tests were performed in dense dry sand on a pile with prototype dimensions...... used for wind turbine foundation. This is important in order to get the right failure mechanism in the sand. The load frame is controlled with a feedback system which enables force controlled load series. A total number of 8 tests have been carried. In all of the tests, the pile was loaded with 500...

  12. Load forecasting method considering temperature effect for distribution network

    Directory of Open Access Journals (Sweden)

    Meng Xiao Fang

    2016-01-01

    Full Text Available To improve the accuracy of load forecasting, the temperature factor was introduced into the load forecasting in this paper. This paper analyzed the characteristics of power load variation, and researched the rule of the load with the temperature change. Based on the linear regression analysis, the mathematical model of load forecasting was presented with considering the temperature effect, and the steps of load forecasting were given. Used MATLAB, the temperature regression coefficient was calculated. Using the load forecasting model, the full-day load forecasting and time-sharing load forecasting were carried out. By comparing and analyzing the forecast error, the results showed that the error of time-sharing load forecasting method was small in this paper. The forecasting method is an effective method to improve the accuracy of load forecasting.

  13. Distributed dynamic load on composite laminates

    Science.gov (United States)

    Langella, A.; Lopresto, V.; Caprino, G.

    2016-05-01

    An experimental activity conducted in order to assess the impact behavior at room and low temperature of carbon fibre in vinylester resin laminates used in the shipbuilding industry, was reported. The conditions which reproduce the impact of a hull at low temperature with a solid body suspended in the water was reproduced. A test equipment was designed and realized to reproduce the real material behaviour in water to obtain a load distribution on the entire surface of the specimen. The results were obtained impacting the laminates placed between the cilyndrical steel impactor and a bag containing water. A falling weight machine, equipped with an instrumented steel impactor and a thermal chamber, was adopted for the experimental tests. The impact behaviour in hostile environments was compared to the behaviour at room temperature and the data obtained under distributed load conditions were compared with the results from concentrated loads: a completely different behaviour was observed between the two different loading conditions in terms of load-displacement curve. The effect of the impact on the laminates has been related with the delaminations, evaluated by ultrasonic scanning, and the indentation.

  14. Power transformer additional load losses separation procedure

    Directory of Open Access Journals (Sweden)

    Kostić Miloje M.

    2011-01-01

    Full Text Available The proposed procedure is based on the fact that total transformer losses (PLL1,n, determined by short circuit test, can be separated into two components: the eddy current losses in the windings (PEC1,n and stray flux losses (PSL1,n in iron parts of construction as well as in the transformer tank walls. The total additional load losses, PLLd1 and PLLdh, are determined by short circuit test results, conducted at rated frequency (f1 and at increased harmonic frequency (fh=h*f1. Using so obtained total additional load losses, PLLd1 and PLLdh, which can be expressed in the form PLLdh=PEC1,n*h2 + PSL1,n*h, the corresponding rate additional load losses values PEC1,n and PSL1,n are derived. At the end, for given load with predefined high harmonics content, (Ih/I1n, relative to rated current, the total additional load losses value ΣPLLdh > PLLd1, is found. In such a way all harmonics up to hmax are taken into account.

  15. Concrete structures under impact loading: general aspects

    Directory of Open Access Journals (Sweden)

    Cornelia Baeră

    2016-09-01

    Full Text Available Dynamic loading conditions distress the structural integrity of a structure differently than the static ones. Such actions transfer high rate strains and instant energy waves to the structure, inducing the possibility of imminent collapse and casualties as a direct consequence. In the latest years, considering the dramatic increase of terrorist threats and global warming, the structural safety criteria imply more than ever the need to withstand this kind of loading (e.g., missiles and blast, projectiles, strong winds, tornados and earthquakes in addition to the static ones. The aim of this paper is to provide a general overview with regard to impact loading in terms of defining the phenomenon from physical and mechanical perspective, its complex local or global effect on the targeted structure, relevant material characteristics, main research approaches, namely theoretical studies and experimental procedures developed for improving the predictability of the dynamic loads and their effects. New directions in developing superior cementitious composites, with better characteristics in terms of dynamic loading performance are also emphasized.

  16. Short term load forecasting: two stage modelling

    Directory of Open Access Journals (Sweden)

    SOARES, L. J.

    2009-06-01

    Full Text Available This paper studies the hourly electricity load demand in the area covered by a utility situated in the Seattle, USA, called Puget Sound Power and Light Company. Our proposal is put into proof with the famous dataset from this company. We propose a stochastic model which employs ANN (Artificial Neural Networks to model short-run dynamics and the dependence among adjacent hours. The model proposed treats each hour's load separately as individual single series. This approach avoids modeling the intricate intra-day pattern (load profile displayed by the load, which varies throughout days of the week and seasons. The forecasting performance of the model is evaluated in similiar mode a TLSAR (Two-Level Seasonal Autoregressive model proposed by Soares (2003 using the years of 1995 and 1996 as the holdout sample. Moreover, we conclude that non linearity is present in some series of these data. The model results are analyzed. The experiment shows that our tool can be used to produce load forecasting in tropical climate places.

  17. Phloem Loading through Plasmodesmata: A Biophysical Analysis.

    Science.gov (United States)

    Comtet, Jean; Turgeon, Robert; Stroock, Abraham D

    2017-10-01

    In many species, Suc en route out of the leaf migrates from photosynthetically active mesophyll cells into the phloem down its concentration gradient via plasmodesmata, i.e. symplastically. In some of these plants, the process is entirely passive, but in others phloem Suc is actively converted into larger sugars, raffinose and stachyose, and segregated (trapped), thus raising total phloem sugar concentration to a level higher than in the mesophyll. Questions remain regarding the mechanisms and selective advantages conferred by both of these symplastic-loading processes. Here, we present an integrated model-including local and global transport and kinetics of polymerization-for passive and active symplastic loading. We also propose a physical model of transport through the plasmodesmata. With these models, we predict that (1) relative to passive loading, polymerization of Suc in the phloem, even in the absence of segregation, lowers the sugar content in the leaf required to achieve a given export rate and accelerates export for a given concentration of Suc in the mesophyll and (2) segregation of oligomers and the inverted gradient of total sugar content can be achieved for physiologically reasonable parameter values, but even higher export rates can be accessed in scenarios in which polymers are allowed to diffuse back into the mesophyll. We discuss these predictions in relation to further studies aimed at the clarification of loading mechanisms, fitness of active and passive symplastic loading, and potential targets for engineering improved rates of export. © 2017 American Society of Plant Biologists. All Rights Reserved.

  18. Fruit load governs transpiration of olive trees

    Science.gov (United States)

    Bustan, Amnon; Dag, Arnon; Yermiyahu, Uri; Erel, Ran; Presnov, Eugene; Agam, Nurit; Kool, Dilia; Iwema, Joost; Zipori, Isaac; Ben-Gal, Alon

    2016-01-01

    We tested the hypothesis that whole-tree water consumption of olives (Olea europaea L.) is fruit load-dependent and investigated the driving physiological mechanisms. Fruit load was manipulated in mature olives grown in weighing-drainage lysimeters. Fruit was thinned or entirely removed from trees at three separate stages of growth: early, mid and late in the season. Tree-scale transpiration, calculated from lysimeter water balance, was found to be a function of fruit load, canopy size and weather conditions. Fruit removal caused an immediate decline in water consumption, measured as whole-plant transpiration normalized to tree size, which persisted until the end of the season. The later the execution of fruit removal, the greater was the response. The amount of water transpired by a fruit-loaded tree was found to be roughly 30% greater than that of an equivalent low- or nonyielding tree. The tree-scale response to fruit was reflected in stem water potential but was not mirrored in leaf-scale physiological measurements of stomatal conductance or photosynthesis. Trees with low or no fruit load had higher vegetative growth rates. However, no significant difference was observed in the overall aboveground dry biomass among groups, when fruit was included. This case, where carbon sources and sinks were both not limiting, suggests that the role of fruit on water consumption involves signaling and alterations in hydraulic properties of vascular tissues and tree organs. PMID:26802540

  19. Modular load flow for restructured power systems

    CERN Document Server

    Hariharan, M V; Gupta, Pragati P

    2016-01-01

    In the subject of power systems, authors felt that a re-look is necessary at some conventional methods of analysis. In this book, the authors have subjected the time-honoured load flow to a close scrutiny. Authors have discovered and discussed a new load flow procedure – Modular Load Flow. Modular Load Flow explores use of power – a scalar – as source for electrical circuits which are conventionally analysed by means of phasors – the ac voltages or currents. The method embeds Kirchhoff’s circuit laws as topological property into its scalar equations and results in a unique wonderland where phase angles do not exist! Generators are shown to have their own worlds which can be superimposed to obtain the state of the composite power system. The treatment is useful in restructured power systems where stakeholders and the system operators may desire to know individual generator contributions in line flows and line losses for commercial reasons. Solution in Modular Load Flow consists of explicit expression...

  20. Power-load curve in trained sprinters.

    Science.gov (United States)

    Alcaraz, Pedro E; Romero-Arenas, Salvador; Vila, Helena; Ferragut, Carmen

    2011-11-01

    The levels of lower-limb strength and power can distinguish between athletes of different levels in a number of sports, specifically in sprinting. In this sense, the purposes of this study were (a) to define the power–load curve in a modified half squat machine in trained sprinters in the competitive cycle and (b) to correlate the peak power (PP) production with 60-m sprint performance. In this sense, a cross-sectional study was carried out with 10 national level sprinters. After the calculation of 1 repetition maximum (1RM) of the participants, a progressive test, which consisted of moving loads of 30, 45, 60, 70, and 80% of the 1RM as quickly as possible in the concentric phase, was performed. It was found that PP occurred at 60% of 1RM. The power output with all loads was not significantly different (p ≤ 0.05) from each other. No significant correlations were found between 60-m performance and PP with the different loads. Therefore, we may conclude that the sprinters of national level analyzed present values of PP output, in the competitive period, near to 60% of 1RM in the half squat exercise; however, this power is not significantly different from the other loads.

  1. Cognitive load measurement as a means to advance cognitive load theory

    NARCIS (Netherlands)

    Paas, F.; Tuovinen, J.E.; Tabbers, H.; van Gerven, P.W.M.

    2003-01-01

    This paper discusses cognitive load measurement techniques with regard to their contribution to cognitive load theory (CLT). CLT is concerned with the design of instructional methods that efficiently use people's limited cognitive processing capacity to apply acquired knowledge and skills to new

  2. Fractographic study of epoxy fractured under mode I loading and mixed mode I/III loading

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Fei [ORNL; Wang, Jy-An John [ORNL; Bertelsen, Williams D. [Gougeon Brothers, Inc.

    2011-01-01

    Fiber reinforced polymeric composite materials are widely used in structural components such as wind turbine blades, which are typically subject to complicated loading conditions. Thus, material response under mixed mode loading is of great significance to the reliability of these structures. Epoxy is a thermosetting polymer that is currently used in manufacturing wind turbine blades. The fracture behavior of epoxy is relevant to the mechanical integrity of the wind turbine composite materials. In this study, a novel fracture testing methodology, the spiral notch torsion test (SNTT), was applied to study the fracture behavior of an epoxy material. SNTT samples were tested using either monotonic loading or cyclic loading, while both mode I and mixed mode I/III loading conditions were used. Fractographic examination indicated the epoxy samples included in this study were prone to mode I failure even when the samples were subject to mixed mode loading. Different fatigue precracks were observed on mode I and mixed mode samples, i.e. precracks appeared as a uniform band under mode I loading, and a semi-ellipse under mixed mode loading. Fracture toughness was also estimated using quantitative fractography.

  3. System ID Modern Control Algorithms for Active Aerodynamic Load Control and Impact on Gearbox Loading

    NARCIS (Netherlands)

    Berg, D.; Wilson, D.; Resor, B.; Berg, J.; Barlas, J.; Crowther, A.; Halse, C.

    2010-01-01

    Prior work on active aerodynamic load control (AALC) of wind turbine blades has demonstrated that appropriate use of this technology has the potential to yield significant reductions in blade loads, leading to a decrease in wind cost of energy. While the general concept of AALC is usually discussed

  4. Method and device for loading packed goods using an intermediate load unit

    NARCIS (Netherlands)

    Reijnen, R.; Ross, L.H.A.; Houlleberghs, B.R.Y.; Naber, J.; Van der Meulen, R.J.R.

    2009-01-01

    The invention relates to a device for loading packed goods into a transport unit (8b), the device comprising an orientation unit for orienting each packed good in a predetermined direction, means for transferring the packed goods in the order of a predetermined loading sequence to the orientation

  5. A Microstructural Study of Load Distribution in Cartilage: A Comparison of Stress Relaxation versus Creep Loading

    Directory of Open Access Journals (Sweden)

    Ashvin Thambyah

    2015-01-01

    Full Text Available The compressive response of articular cartilage has been extensively investigated and most studies have focussed largely on the directly loaded matrix. However, especially in relation to the tissue microstructure, less is known about load distribution mechanisms operating outside the directly loaded region. We have addressed this issue by using channel indentation and DIC microscopy techniques that provide visualisation of the matrix microstructural response across the regions of both direct and nondirect loading. We hypothesise that, by comparing the microstructural response following stress relaxation and creep compression, new insights can be revealed concerning the complex mechanisms of load bearing. Our results indicate that, with stress relaxation, the initial mode of stress decay appears to primarily involve relaxation of the surface layer. In the creep loading protocol, the main mode of stress release is a lateral distribution of load via the mid matrix. While these two modes of stress redistribution have a complex relationship with the zonally differentiated tissue microstructure and the depth of strain, four mechanostructural mechanisms are proposed to describe succinctly the load responses observed.

  6. Bit Loading Algorithms for Cooperative OFDM Systems

    Directory of Open Access Journals (Sweden)

    Bo Gui

    2007-12-01

    Full Text Available We investigate the resource allocation problem for an OFDM cooperative network with a single source-destination pair and multiple relays. Assuming knowledge of the instantaneous channel gains for all links in the entire network, we propose several bit and power allocation schemes aiming at minimizing the total transmission power under a target rate constraint. First, an optimal and efficient bit loading algorithm is proposed when the relay node uses the same subchannel to relay the information transmitted by the source node. To further improve the performance gain, subchannel permutation, in which the subchannels are reallocated at relay nodes, is considered. An optimal subchannel permutation algorithm is first proposed and then an efficient suboptimal algorithm is considered to achieve a better complexity-performance tradeoff. A distributed bit loading algorithm is also proposed for ad hoc networks. Simulation results show that significant performance gains can be achieved by the proposed bit loading algorithms, especially when subchannel permutation is employed.

  7. Integrated microelectromechanical gyroscope under shock loads

    Science.gov (United States)

    Nesterenko, T. G.; Koleda, A. N.; Barbin, E. S.

    2018-01-01

    The paper presents a new design of a shock-proof two-axis microelectromechanical gyroscope. Without stoppers, the shock load enables the interaction between the silicon sensor elements. Stoppers were installed in the gyroscope to prevent the contact interaction between electrodes and spring elements with fixed part of the sensor. The contact of stoppers occurs along the plane, thereby preventing the system from serious contact stresses. The shock resistance of the gyroscope is improved by the increase in its eigenfrequency at which the contact interaction does not occur. It is shown that the shock load directed along one axis does not virtually cause the movement of sensing elements along the crosswise axes. Maximum stresses observed in the proposed gyroscope at any loading direction do not exceed the value allowable for silicon.

  8. Free Material Design with Multiple Load Cases

    DEFF Research Database (Denmark)

    Pedersen, Pauli; Pedersen, Niels Leergaard

    2012-01-01

    Multiple load cases and the consideration of strength is a reality that most structural designs are exposed to. Improved possibility to produce specific materials, say by fiber lay-up, put focus on research on free material optimization. A formulation for such design problems together with a prac......Multiple load cases and the consideration of strength is a reality that most structural designs are exposed to. Improved possibility to produce specific materials, say by fiber lay-up, put focus on research on free material optimization. A formulation for such design problems together...... with a practical recursive design procedure is presented and illustrated with examples. The presented finite element analysis involve many elements as well as many load cases. Separating the local amount of material from a description with unit trace for the local anisotropy, gives the free materials formulation...

  9. Design Load Basis for Offshore Wind turbines

    DEFF Research Database (Denmark)

    Natarajan, Anand; Hansen, Morten Hartvig; Wang, Shaofeng

    2016-01-01

    DTU Wind Energy is not designing and manufacturing wind turbines and does therefore not need a Design Load Basis (DLB) that is accepted by a certification body. However, to assess the load consequences of innovative features and devices added to existing offshore turbine concepts or new offshore...... turbine concept developed in our research, it is useful to have a full DLB that follows the current design standard and is representative of a general DLB used by the industry. It will set a standard for the offshore wind turbine design load evaluations performed at DTU Wind Energy, which is aligned...... with the challenges faced by the industry and therefore ensures that our research continues to have a strong foundation in this interaction. Furthermore, the use of a full DLB that follows the current standard can improve and increase the feedback from the research at DTU Wind Energy to the international...

  10. Managing the Training Load in Adolescent Athletes.

    Science.gov (United States)

    Murray, Andrew

    2017-04-01

    While historically adolescents were removed from their parents to prepare to become warriors, this process repeats itself in modern times but with the outcome being athletic performance. This review considers the process of developing athletes and managing load against the backdrop of differing approaches of conserving and maximizing the talent available. It acknowledges the typical training "dose" that adolescent athletes receive across a number of sports and the typical "response" when it is excessive or not managed appropriately. It also examines the best approaches to quantifying load and injury risk, acknowledging the relative strengths and weaknesses of subjective and objective approaches. Making evidence-based decisions is emphasized, while the appropriate monitoring techniques are determined by both the sporting context and individual situation. Ultimately a systematic approach to training-load monitoring is recommended for adolescent athletes to both maximize their athletic development and allow an opportunity for learning, reflection, and enhancement of performance knowledge of coaches and practitioners.

  11. Contact Sliding under Relatively Low Loads

    Directory of Open Access Journals (Sweden)

    Kyeong Hee Kang

    2011-01-01

    Full Text Available ZnO nanowires have received much interest owing to their particular structural and piezoelectric properties. For widespread application of ZnO nanowires in various nanotechnologies, the mechanical reliability of the nanowires should be assessed. In this paper, the damage characteristics of vertically grown ZnO nanowires due to contact sliding against a 2 mm diameter steel ball under relatively low loads were investigated. Frictional behavior and wear characteristics of the specimens were assessed. Furthermore, contact sliding tests were performed inside an SEM to monitor the progression of damage of the nanowires. It was found that the friction coefficient was about 0.35 under all loads while the damage characteristics of the nanowires were quite different for each load. The large diameter nanowires tended to fracture earlier than the small diameter nanowires. Wear tests performed inside the SEM confirmed the surface damage characteristics observed during the friction tests.

  12. Lower head integrity under steam explosion loads

    Energy Technology Data Exchange (ETDEWEB)

    Theofanous, T.G.; Yuen, W.W.; Angelini, S.; Freeman, K.; Chen, X.; Salmassi, T. [Center for Risk Studies and Safety, Univ. of California, Santa Barbara, CA (United States); Sienicki, J.J.

    1998-01-01

    Lower head integrity under steam explosion loads in an AP600-like reactor design is considered. The assessment is the second part of an evaluation of the in-vessel retention idea as a severe accident management concept, the first part (DOE/ID-10460) dealing with thermal loads. The assessment is conducted in terms of the Risk Oriented Accident Analysis Methodology (ROAAM), and includes the comprehensive evaluation of all relevant severe accident scenarios, melt conditions and timing of release from the core region, fully 3D mixing and explosion wave dynamics, and lower head fragility under local, dynamic loading. All of these factors and brought together in a ROAAM Probabilistic Framework to evaluate failure likelihood. The conclusion is that failure is `physically unreasonable`. (author)

  13. Radio Frequency Power Load and Associated Method

    Science.gov (United States)

    Srinivasan, V. Karthik (Inventor); Freestone, Todd M. (Inventor); Sims, William Herbert, III (Inventor)

    2014-01-01

    A radio frequency power load and associated method. A radio frequency power load apparatus may include a container with an ionized fluid therein. The apparatus may include one conductor immersed in a fluid and another conductor electrically connected to the container. A radio frequency transmission system may include a radio frequency transmitter, a radio frequency amplifier connected to the transmitter and a radio frequency power load apparatus connected to the amplifier. The apparatus may include a fluid having an ion source therein, one conductor immersed in a fluid, and another conductor electrically connected to the container. A method of dissipating power generated by a radio frequency transmission system may include constructing a waveguide with ionized fluid in a container and connecting the waveguide to an amplifier of the transmission system.

  14. Bit Loading Algorithms for Cooperative OFDM Systems

    Directory of Open Access Journals (Sweden)

    Gui Bo

    2008-01-01

    Full Text Available Abstract We investigate the resource allocation problem for an OFDM cooperative network with a single source-destination pair and multiple relays. Assuming knowledge of the instantaneous channel gains for all links in the entire network, we propose several bit and power allocation schemes aiming at minimizing the total transmission power under a target rate constraint. First, an optimal and efficient bit loading algorithm is proposed when the relay node uses the same subchannel to relay the information transmitted by the source node. To further improve the performance gain, subchannel permutation, in which the subchannels are reallocated at relay nodes, is considered. An optimal subchannel permutation algorithm is first proposed and then an efficient suboptimal algorithm is considered to achieve a better complexity-performance tradeoff. A distributed bit loading algorithm is also proposed for ad hoc networks. Simulation results show that significant performance gains can be achieved by the proposed bit loading algorithms, especially when subchannel permutation is employed.

  15. Phloem loading through plasmodesmata: a biophysical analysis

    CERN Document Server

    Comtet, Jean; Stroock, Abraham D

    2016-01-01

    In many species, sucrose en route out of the leaf migrates from photosynthetically active mesophyll cells into the phloem down its concentration gradient via plasmodesmata, i.e., symplastically. In some of these plants the process is entirely passive, but in others phloem sucrose is actively converted into larger sugars, raffinose and stachyose, and segregated (trapped), thus raising total phloem sugar concentration to a level higher than in the mesophyll. Questions remain regarding the mechanisms and selective advantages conferred by both of these symplastic loading processes. Here we present an integrated model - including local and global transport and the kinetics of oligomerization - for passive and active symplastic loading. We also propose a physical model of transport through the plasmodesmata. With these models, we predict that: 1) relative to passive loading, oligomerization of sucrose in the phloem, even in the absence of segregation, lowers the sugar content in the leaf required to achieve a given...

  16. Compensator configurations for load currents' symmetrization

    Science.gov (United States)

    Rusinaru, D.; Manescu, L. G.; Dinu, R. C.

    2016-02-01

    This paper approaches aspects regarding the mitigation effects of asymmetries in 3-phase 3-wire networks. The measure consisting in connecting of load current symmetrization devices at the load coupling point is presented. A time-variation of compensators parameters is determined as a function of the time-recorded electrical values. The general sizing principle of the load current symmetrization reactive components is based on a simple equivalent model of the unbalanced 3-phase loads. By using these compensators a certain control of the power components transits is ensured in the network. The control is based on the variations laws of the compensators parameters as functions of the recorded electrical values: [B] = [T]·[M]. The link between compensator parameters and measured values is ensured by a transformation matrix [T] for each operation conditions of the supply network. Additional conditions for improving of energy and efficiency performance of the compensator are considered: i.e. reactive power compensation. The compensator sizing algorithm was implemented into a MATLAB environment software, which generate the time-evolution of the parameters of load current symmetrization device. The input data of application takes into account time-recording of the electrical values. By using the compensator sizing software, some results were achieved for the case of a consumer connected at 20 kV busbar of a distribution substation, during 24 hours measurement session. Even the sizing of the compensators aimed some additional network operation aspects (power factor correction) correlated with the total or major load symmetrizations, the harmonics aspects of the network values were neglected.

  17. Laguna Verde annulus pressurization loads evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Castaneda, M. A.; Cruz, M. A.; Cardenas, J. B.; Vargas, A.; Cruz, H. J.; Mercado, J. J., E-mail: miguel.castaneda01@cfe.gob.m [Comision Federal de Electricidad, Central Nucleoelectrica de Laguna Verde, Km. 42.5 Carretera Cardel-Nautla, Veracruz (Mexico)

    2010-10-15

    Annulus pressurization, jet impingement, pipe whip restraint and jet thrust are phenomena related to postulated pipe ruptures. A postulated pipe rupture at the weld between recirculation, or feedwater piping and a reactor nozzle safe end, will lead to a high flow rate of flashing water/steam mixture into the annulus between the reactor pressure vessel and the biological shield wall. The total effect of the vessel and pipe inventory blowdown from the break being postulated must be accounted for in the evaluation. A recirculation line break will give rise to an angular dependent short term pressure differential around the vessel, followed by a longer term pressure buildup in the annulus. A recirculation line postulated rupture may not produce worst case conditions and reference to time intervals for only the recirculation break should be treated superficially. A postulated rupture of the feedwater piping may produce the extreme case for determining: 1) the shield wall and reactor vessel to pedestal interactions, 2) loading on the reactor vessel internals, or 3) responses for the balance of piping attached to the vessel. Recently it was identified a potential issue regarding the criteria used to determine which cases were evaluated for Annulus Pressurization (A P) loads for new loads plants. The original A P loads methodology in the late 1970 and early 1980 years separated the mass/energy release calculation from the structural response calculation based on the implicit assumption that the maximum overall mass/energy release will result in maximizing the structural response and corresponding stresses on the reactor pressure vessel, internals, and containment structures. This process did not consider the dynamic response in the primary and secondary safety related structures, components and equipment. Consequently, the A P loads used as input for design adequacy evaluations of Nuclear Steam Supply System safety related components for new loads plants might have

  18. Reduction of date microbial load with ozone

    Science.gov (United States)

    Farajzadeh, Davood; Qorbanpoor, Ali; Rafati, Hasan; Isfeedvajani, Mohsen Saberi

    2013-01-01

    Background: Date is one of the foodstuffs that are produced in tropical areas and used worldwide. Conventionally, methyl bromide and phosphine are used for date disinfection. The toxic side effects of these usual disinfectants have led food scientists to consider safer agents such as ozone for disinfection, because food safety is a top priority. The present study was performed to investigate the possibility of replacing common conventional disinfectants with ozone for date disinfection and microbial load reduction. Materials and Methods: In this experimental study, date samples were ozonized for 3 and 5 hours with 5 and 10 g/h concentrations and packed. Ozonized samples were divided into two groups and kept in an incubator which was maintained at 25°C and 40°C for 9 months. During this period, every 3 month, microbial load (bacteria, mold, and yeast) were examined in ozonized and non-ozonized samples. Results: This study showed that ozonization with 5 g/h for 3 hours, 5 g/h for 5 hours, 10 g/h for 3 hours, and 10 g/h for 5 hours leads to about 25%, 25%, 53%, and 46% reduction in date mold and yeast load and about 6%, 9%, 76%, and 74.7% reduction in date bacterial load at baseline phase, respectively. Appropriate concentration and duration of ozonization for microbial load reduction were 10 g/h and 3 hours. Conclusion: Date ozonization is an appropriate method for microbial load reduction and leads to an increase in the shelf life of dates. PMID:24124432

  19. INFLUENCE OF MOVING LOADS ON CURVED BRIDGES

    OpenAIRE

    Thamer A. Z*, Jabbbar S. A

    2016-01-01

    The behavior of a curved slab bridge decks with uniform thickness under moving load is investigated in this study. Three radii of curvature "R" are used (25, 50 and 75m) along with the straight bridge, R = ∞. The decks are simply supported or clamped along the radial edges and free at the circular edges. The AASHTO[1] standard axle load of the truck H20-44 is used and assumed to move in three track positions on the bridge. The finite element method is employed for the analysis and the ANSYS 5...

  20. Practical Hydrogen Loading of Air Silica Fibres

    DEFF Research Database (Denmark)

    Sørensen, Henrik Rokkjær; Jensen, Jesper Bevensee; Jensen, Jesper Bo Damm

    2005-01-01

    A method for hydrogen-loading air-silica optical fibres has been developed allowing out-diffusion times comparable to standard step-index fibres. Examples of the first grating written in Ge-doped air-silica fibres using a 266nm UV-laser are shown.......A method for hydrogen-loading air-silica optical fibres has been developed allowing out-diffusion times comparable to standard step-index fibres. Examples of the first grating written in Ge-doped air-silica fibres using a 266nm UV-laser are shown....

  1. Inferential Framework for Autonomous Cryogenic Loading Operations

    Science.gov (United States)

    Luchinsky, Dmitry G.; Khasin, Michael; Timucin, Dogan; Sass, Jared; Perotti, Jose; Brown, Barbara

    2017-01-01

    We address problem of autonomous cryogenic management of loading operations on the ground and in space. As a step towards solution of this problem we develop a probabilistic framework for inferring correlations parameters of two-fluid cryogenic flow. The simulation of two-phase cryogenic flow is performed using nearly-implicit scheme. A concise set of cryogenic correlations is introduced. The proposed approach is applied to an analysis of the cryogenic flow in experimental Propellant Loading System built at NASA KSC. An efficient simultaneous optimization of a large number of model parameters is demonstrated and a good agreement with the experimental data is obtained.

  2. Load and Global Response of Ships

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher

    The present monograph covers wave load and global structural response for ships. It is primary written as a textbook for students with an introductionary background in naval architecture and a basic knowledge of statistics and strength of materials. The subjects are treated in details starting from...... first principles. The aim has been to derive and present the necessary theoretical framework for predicting the extreme loads and the corresponding hull girder stresses the ship may be subjected to during its operational lifetime.Although some account is given to reliabiity analysis, the present...

  3. Pressure Hull Analysis under Shock Loading

    Directory of Open Access Journals (Sweden)

    Ya-Jung Lee

    2008-01-01

    Full Text Available The hull of high performance submarines must resist underwater shock loading due to exploding torpedoes or depth bombs. An underwater shock involving an initial shock wave and successive bubble pulsating waves is so complex that a theoretical technique for deriving shock pressure distribution is required for improving simulation efficiency. Complete shock loading is obtained theoretically in this work, and responses of a submarine pressure hull are calculated using ABAQUS USA (Underwater Shock Analysis codes. In the long run, this deflection and stress data will assist in examining the structural arrangement of the submarine pressure hull.

  4. Stochastic Extreme Load Predictions for Marine Structures

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher

    1999-01-01

    Development of rational design criteria for marine structures requires reliable estimates for the maximum wave-induced loads the structure may encounter during its operational lifetime. The paper discusses various methods for extreme value predictions taking into account the non-linearity of the ......Development of rational design criteria for marine structures requires reliable estimates for the maximum wave-induced loads the structure may encounter during its operational lifetime. The paper discusses various methods for extreme value predictions taking into account the non...

  5. Design of Vickers Hardness Loading Controller

    Directory of Open Access Journals (Sweden)

    Sihai Zhao

    2014-09-01

    Full Text Available Traditionally Vickers testing needs manual works, as a result, it will induce low precision and automatization. So this paper design a new type of loading controlling system, it is based on single chip computer 89S52, used PZT as the force generator in micro Vickers hardness testing. It primarily includes the designing of hardware, software of collecting data and PZT signals by AD667. This article has given the sketch of electrical circuit and controlling software, it also offers the experiment data. The experiments have showed that using this system can exactly control the loading results, and the average tolerance is less than 0.43 %.

  6. Intelligent electrical outlet for collective load control

    Science.gov (United States)

    Lentine, Anthony L.; Ford, Justin R.; Spires, Shannon V.; Goldsmith, Steven Y.

    2015-10-27

    Various technologies described herein pertain to an electrical outlet that autonomously manages loads in a microgrid. The electrical outlet can provide autonomous load control in response to variations in electrical power generation supply in the microgrid. The electrical outlet includes a receptacle, a sensor operably coupled to the receptacle, and an actuator configured to selectively actuate the receptacle. The sensor measures electrical parameters at the receptacle. Further, a processor autonomously controls the actuator based at least in part on the electrical parameters measured at the receptacle, electrical parameters from one or more disparate electrical outlets in the microgrid, and a supply of generated electric power in the microgrid at a given time.

  7. Pile Load Capacity – Calculation Methods

    Directory of Open Access Journals (Sweden)

    Wrana Bogumił

    2015-12-01

    Full Text Available The article is a review of the current problems of the foundation pile capacity calculations. The article considers the main principles of pile capacity calculations presented in Eurocode 7 and other methods with adequate explanations. Two main methods are presented: α – method used to calculate the short-term load capacity of piles in cohesive soils and β – method used to calculate the long-term load capacity of piles in both cohesive and cohesionless soils. Moreover, methods based on cone CPTu result are presented as well as the pile capacity problem based on static tests.

  8. Gust loading on streamlined bridge decks

    DEFF Research Database (Denmark)

    Larose, Guy; Mann, Jakob

    1998-01-01

    The current analytical description of the buffeting action of wind on long-span bridges is based on the strip assumption. However, recent experiments on closed-box girder bridge decks have shown that this assumption is not valid and is the source of an important part of the error margin...... of the analytical prediction methods. In this paper, an analytical model that departs from the strip assumption is used to describe the gust loading on a thin airfoil. A parallel is drawn between the analytical model and direct measurements of gust loading on motionless closed-box girder bridge decks. Empirical...

  9. Comparison of Deterministic and Probabilistic Radial Distribution Systems Load Flow

    Science.gov (United States)

    Gupta, Atma Ram; Kumar, Ashwani

    2017-08-01

    Distribution system network today is facing the challenge of meeting increased load demands from the industrial, commercial and residential sectors. The pattern of load is highly dependent on consumer behavior and temporal factors such as season of the year, day of the week or time of the day. For deterministic radial distribution load flow studies load is taken as constant. But, load varies continually with a high degree of uncertainty. So, there is a need to model probable realistic load. Monte-Carlo Simulation is used to model the probable realistic load by generating random values of active and reactive power load from the mean and standard deviation of the load and for solving a Deterministic Radial Load Flow with these values. The probabilistic solution is reconstructed from deterministic data obtained for each simulation. The main contribution of the work is: Finding impact of probable realistic ZIP load modeling on balanced radial distribution load flow. Finding impact of probable realistic ZIP load modeling on unbalanced radial distribution load flow. Compare the voltage profile and losses with probable realistic ZIP load modeling for balanced and unbalanced radial distribution load flow.

  10. Comparison of Deterministic and Probabilistic Radial Distribution Systems Load Flow

    Science.gov (United States)

    Gupta, Atma Ram; Kumar, Ashwani

    2017-12-01

    Distribution system network today is facing the challenge of meeting increased load demands from the industrial, commercial and residential sectors. The pattern of load is highly dependent on consumer behavior and temporal factors such as season of the year, day of the week or time of the day. For deterministic radial distribution load flow studies load is taken as constant. But, load varies continually with a high degree of uncertainty. So, there is a need to model probable realistic load. Monte-Carlo Simulation is used to model the probable realistic load by generating random values of active and reactive power load from the mean and standard deviation of the load and for solving a Deterministic Radial Load Flow with these values. The probabilistic solution is reconstructed from deterministic data obtained for each simulation. The main contribution of the work is: Finding impact of probable realistic ZIP load modeling on balanced radial distribution load flow. Finding impact of probable realistic ZIP load modeling on unbalanced radial distribution load flow. Compare the voltage profile and losses with probable realistic ZIP load modeling for balanced and unbalanced radial distribution load flow.

  11. 46 CFR 154.355 - Bow and stern loading piping.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Bow and stern loading piping. 154.355 Section 154.355... Arrangements § 154.355 Bow and stern loading piping. (a) Bow and stern loading piping must: (1) Meet § 154.310... other openings to accommodation, service, or control spaces that face the bow or stern loading area must...

  12. 14 CFR 23.393 - Loads parallel to hinge line.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Loads parallel to hinge line. 23.393... Control Surface and System Loads § 23.393 Loads parallel to hinge line. (a) Control surfaces and supporting hinge brackets must be designed to withstand inertial loads acting parallel to the hinge line. (b...

  13. 24 CFR 3285.315 - Special snow load conditions.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Special snow load conditions. 3285... Special snow load conditions. (a) General. Foundations for homes designed for and located in areas with roof live loads greater than 40 psf must be designed by the manufacturer for the special snow load...

  14. 14 CFR 23.371 - Gyroscopic and aerodynamic loads.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Gyroscopic and aerodynamic loads. 23.371... Flight Loads § 23.371 Gyroscopic and aerodynamic loads. (a) Each engine mount and its supporting structure must be designed for the gyroscopic, inertial, and aerodynamic loads that result, with the engine...

  15. Transient Monotonic and Cyclic Load Effects on Mono Bucket Foundations

    DEFF Research Database (Denmark)

    Nielsen, Søren Dam

    and when hitting the foundation they induce high impact loads with a short duration. It is important that the foundation is able to resists these huge loads. Fortunately, the conducted research showed that the capacity of the mono bucket foundation is high to impact loads. When exposed to a huge wave load...

  16. The inverse effects of load transfer and load sharing on axial compressive stiffness.

    Science.gov (United States)

    Haher, T R; Yeung, A W; Ottaviano, D M; Merola, A A; Caruso, S A

    2001-01-01

    The goal of spinal instrumentation is to stabilize involved motion segments while fusion occurs. Although some degree of load sharing is necessary for fusion, the ability of the instrumentation system to transfer the load may vary. The purpose of this study is to formulate a mathematical relationship between load sharing and load transfer of specific spinal instrumentation systems using a well-accepted mechanical model. Forty-eight American Society for Testing Materials standard ultra high molecular weight polyethylene cylinders were used as per designation F 1717-96, standard test methods for static and fatigue for spinal implant constructs in a corpectomy model. Twenty-four spinal assemblies consisting of anterior plates, anterior rod, and posterior rods were subjected to compression bending tests using a MTS Bionix servo-hydraulic material testing apparatus. Each implant was tested in compression bending with and without the addition of a titanium load-sharing cage. The force applied was the independent variable, and the displacement was the dependent variable. The stiffness was determined for each setup with and without the addition of an anterior load-sharing cage. The average axial compressive stiffness of a system increased by a factor of 8.5 with the addition of the load-sharing cage. An inverse relationship existed between the compressive stiffness of the construct and its relative increase achieved with the addition of the load-sharing cage. The compressive stiffness of the system with the addition of the load-sharing cage approached that of the anterior device itself as the system flexibility increased. The ability of instrumentation systems to load share or load transfer and their respective stiffness was determined. The 5-mm rod screw posterior system was compared with the 7-mm Ti posterior system with the addition of one and two devices for transverse traction (DTTs). The rods with the increased diameter had a stiffness of 1723 n/mm with one DTT and

  17. Allocation of Load-Loss Cost Caused by Voltage Sag

    Science.gov (United States)

    Gao, X.

    2017-10-01

    This paper focuses on the allocation of load-loss cost caused by voltage sag in the environment of electricity market. To compensate the loss of loads due to voltage sags, the load-loss cost is allocated to both sources and power consumers. On the basis of Load Drop Cost (LDC), a quantitative evaluation index of load-loss cost caused by voltage sag is identified. The load-loss cost to be allocated to power consumers themselves is calculated according to load classification. Based on the theory of power component the quantitative relation between sources and loads is established, thereby a quantitative calculation method for load-loss cost allocated to each source is deduced and the quantitative compensation from individual source to load is proposed. A simple five-bus system illustrates the main features of the proposed method.

  18. Outlier robustness for wind turbine extrapolated extreme loads

    DEFF Research Database (Denmark)

    Natarajan, Anand; Verelst, David Robert

    2012-01-01

    simulation is demonstrated and compared with published results. Further effects of varying wind inflow angles and shear exponent is brought out. Parametric fitting techniques that consider all extreme loads including ‘outliers’ are proposed, and the physical reasons that result in isolated high extreme loads...... dependencies is utilized to estimate a probability for the largest extreme load to occur at a specific mean wind speed. This inherently weights extreme loads that occur frequently within mean wind speed bins higher than isolated occurrences of extreme loads. Primarily, the results for the blade root out......-of-plane loads are presented here as those extrapolated loads have shown wide variability in literature, but the method can be generalized to any other component load. The convergence of the 1 year extrapolated extreme blade root out-of-plane load with the number of turbulent wind samples used in the loads...

  19. 46 CFR 78.50-15 - Load line marks.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Load line marks. 78.50-15 Section 78.50-15 Shipping... Vessels § 78.50-15 Load line marks. (a) Vessels assigned a load line shall have the deck line and the load line marks permanently scribed or embossed as required by subchapter E (Load Lines) of this chapter. (b) ...

  20. A grid-tied PV system for commercial load and peak load reduction: South African case study

    CSIR Research Space (South Africa)

    Senatla, Mamahloko

    2017-08-01

    Full Text Available in the analysis with the objective of reducing both the load demand and peak load for a South African commercial entity. The results show load and peak load reductions of 3.4% and 4.5 % respectively. This shows that if such or similar systems are adopted...

  1. Load Management in District Heating Operation

    DEFF Research Database (Denmark)

    Li, Hongwei; Wang, Stephen Jia

    2015-01-01

    Smooth operation of district heating system will avoid installation of expensive peak heat boilers, improve plant partial load performance, increase the system redundancy for further network expansion and improve its resilience to ensure security of supply during severe heating seasons. The peak...

  2. Work load and musculoskeletal complaints during pregnancy

    NARCIS (Netherlands)

    Paul, J. A.; van Dijk, F. J.; Frings-Dresen, M. H.

    1994-01-01

    Many pregnant women have musculoskeletal complaints, the onset and aggravation of which are thought to be associated with their activity or work postures. The purpose of this paper was to obtain more insight into the influence of pregnancy on the load of the musculoskeletal system at work to provide

  3. Preparation and Evaluation of Glibenclamide-Loaded ...

    African Journals Online (AJOL)

    The effect of stirring speed (250, 1000, 1500 and 2500 rpm) and drug: polymer ratio (1:1, 1: 2, 1:3 and 2:1) on particle size, size distribution, zeta potential, drug loading, encapsulation efficiency and drug release was also studied. Results: Stable NPs were successfully prepared without any incompatibility, as indicated by ...

  4. The chemistry induced by mechanical load

    CERN Document Server

    Frank, Irmgard

    2016-01-01

    Results in the field of mechanochemistry are summarized. For example under mechanical load often a solvolysis is observed instead of a simple homolytic bond rupture. Also a mechanically induced redox reaction was reported experimentally and could be modelled theoretically. With CPMD simulations it is possible to understand multi-step mechanisms in full detail.

  5. 14 CFR 23.443 - Gust loads.

    Science.gov (United States)

    2010-01-01

    ... Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Vertical Surfaces § 23.443... specified in § 23.333(c)(2)(i). (c) In the absence of a more rational analysis, the gust load must be...

  6. 14 CFR 23.425 - Gust loads.

    Science.gov (United States)

    2010-01-01

    ... Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Horizontal Stabilizing and...) In the absence of a more rational analysis, the incremental load due to the gust must be computed as...

  7. Load capacity of hollowed timber piles.

    Science.gov (United States)

    1998-12-01

    The goal of this study was to develop a reliable load-rating methodology for timber piles based on the level of documented damage. Louisiana currently has over 4,000 timber bridges in its inventory of over 13,800 bridges. A quarter of these 4,000 tim...

  8. Vocal Loading in Speaking a Foreign Language.

    Science.gov (United States)

    Järvinen, Kati; Laukkanen, Anne-Maria

    2015-01-01

    This study investigated whether speaking a foreign language affects the subjective notions of vocal fatigue, and whether acoustic measurements reveal a higher vocal loading. The speech samples of 20 native Finnish-speaking and 23 native English-speaking subjects were recorded in Finnish and in English. From the speech samples, fundamental frequency, equivalent sound level, total duration of voiced speech, speech rate, alpha ratio and L1-L0 level difference were analyzed. Vocal doses were calculated. According to subjective notions, the voice gets tired more quickly when speaking a foreign language. The mean fundamental frequency increased but the speech rate and total duration of voiced speech decreased significantly when speaking a foreign language. Thus, the vocal doses decreased. The subjective sensations of increased vocal fatigue may be due to increased mental stress rather than to higher vocal loading. However, a trend that speaking a foreign language may involve more loading was found in L1-L0 level difference and in the doses normalized to time dose. Longer speech samples should be studied. Voice quality-based indicators of vocal loading are worth testing in addition to the measures based on the amount of voicing in speech. © 2015 S. Karger AG, Basel.

  9. Maritime Load Dependent Lead Times - An Analysis

    DEFF Research Database (Denmark)

    Pahl, Julia; Voss, Stefan

    2017-01-01

    Traditionally, the maritime sector follows a very conservative approach towards sharing information and adopting information technology (IT) to stream-line logistic activities. Late arrivals of ships create problems especially with the trend to build large ships leading to peak loads of process...

  10. Critical Buckling Load on Large Spherical Shells

    DEFF Research Database (Denmark)

    Wedellsborg, B. W.

    1962-01-01

    Approximate evaluation for watertanks, hortonspheres, vapor containers, containment vessels for nuclear reactors, and so forth, has been computed, taking into account out-of-roundness and local flattened areas; graphs have been plotted giving critical buckling load as function of maximum radial...

  11. Stormwater contaminant loading following southern California wildfires.

    Science.gov (United States)

    Stein, Eric D; Brown, Jeffrey S; Hogue, Terri S; Burke, Megan P; Kinoshita, Alicia

    2012-11-01

    Contaminant loading associated with stormwater runoff from recently burned areas is poorly understood, despite the fact that it has the potential to affect downstream water quality. The goal of the present study is to assess regional patterns of runoff and contaminant loading from wildfires in urban fringe areas of southern California. Postfire stormwater runoff was sampled from five wildfires that each burned between 115 and 658 km(2) of natural open space between 2003 and 2009. Between two and five storm events were sampled per site over the first one to two years following the fires for basic constituents, metals, nutrients, total suspended solids, and polycyclic aromatic hydrocarbons (PAHs). Results were compared to data from 16 unburned natural areas and six developed sites. Mean copper, lead, and zinc flux (kg/km(2)) were between 112- and 736-fold higher from burned catchments and total phosphorus was up to 921-fold higher compared to unburned natural areas. Polycyclic aromatic hydrocarbon flux was four times greater from burned areas than from adjacent urban areas. Ash fallout on nearby unburned watersheds also resulted in a threefold increase in metals and PAHs. Attenuation of elevated concentration and flux values appears to be driven mainly by rainfall magnitude. Contaminant loading from burned landscapes has the potential to be a substantial contribution to the total annual load to downstream areas in the first several years following fires. Copyright © 2012 SETAC.

  12. Effects of Cognitive Load on Speech Recognition

    Science.gov (United States)

    Mattys, Sven L.; Wiget, Lukas

    2011-01-01

    The effect of cognitive load (CL) on speech recognition has received little attention despite the prevalence of CL in everyday life, e.g., dual-tasking. To assess the effect of CL on the interaction between lexically-mediated and acoustically-mediated processes, we measured the magnitude of the "Ganong effect" (i.e., lexical bias on phoneme…

  13. Liquid loading experiments with tube wall modifications

    NARCIS (Netherlands)

    Belfroid, S.P.C.; Schiferli, W.; Veltin, J.; Veeken, K.

    2011-01-01

    This paper discusses the multiphase flow mechanism responsible for gas-well liquid loading. It demonstrates that the conventional idea of droplet flow reversal (Turner et al. (1)) does not capture reality and that actual observations are better described by film flow reversal phenomenon. The

  14. A heavy load for heavy ions

    CERN Multimedia

    2003-01-01

    On 25 September, the two large coils for the dipole magnet of ALICE, the LHC experiment dedicated to heavy ions, arrived at Point 2 on two heavy load trucks after a 1200 km journey from their assembly in Vannes, France.

  15. Global Cryptosporidium Loads from Livestock Manure

    NARCIS (Netherlands)

    Vermeulen-Henstra, Lucie; Benders, Jorien; Medema, Gertjan; Hofstra, Nynke

    2017-01-01

    Understanding the environmental pathways of Cryptosporidium is essential for effective management of human and animal cryptosporidiosis. In this paper we aim to quantify livestock Cryptosporidium spp. loads to land on a global scale using spatially explicit process-based modeling, and to explore the

  16. Measuring Cognitive Load in Embodied Learning Settings

    Science.gov (United States)

    Skulmowski, Alexander; Rey, Günter Daniel

    2017-01-01

    In recent years, research on embodied cognition has inspired a number of studies on multimedia learning and instructional psychology. However, in contrast to traditional research on education and multimedia learning, studies on embodied learning (i.e., focusing on bodily action and perception in the context of education) in some cases pose new problems for the measurement of cognitive load. This review provides an overview over recent studies on embodied learning in which cognitive load was measured using surveys, behavioral data, or physiological measures. The different methods are assessed in terms of their success in finding differences of cognitive load in embodied learning scenarios. At the same time, we highlight the most important challenges for researchers aiming to include these measures into their study designs. The main issues we identified are: (1) Subjective measures must be appropriately phrased to be useful for embodied learning; (2) recent findings indicate potentials as well as problematic aspects of dual-task measures; (3) the use of physiological measures offers great potential, but may require mobile equipment in the context of embodied scenarios; (4) meta-cognitive measures can be useful extensions of cognitive load measurement for embodied learning. PMID:28824473

  17. Large Scale Demand Response of Thermostatic Loads

    DEFF Research Database (Denmark)

    Totu, Luminita Cristiana

    the temperature limits and other operational constraints, and by using only limited communication, it is possible to make use of the individual thermostat deadband flexibility to step-up or step-down the power consumption of the population as if it were a power plant. The individual thermostatic loads experience...

  18. Immediate implant loading: A case report

    OpenAIRE

    Dhamankar, Dilip; Gupta, Arun R.; Mahadevan, Janani

    2010-01-01

    Dental implants have long provided an excellent treatment option to restore edentulous spaces. Successful formation of a direct bone to implant interface is the goal in implant therapy. Immediate loading is an alternative to two stage surgical procedure. Improved surgical instrumentation implants design, and surface topography changes the concept of two stages surgical to one stage surgical procedure.

  19. Automatic Multimodal Cognitive Load Measurement (AMCLM)

    Science.gov (United States)

    2011-06-01

    activity is growing, measurement systems have yet to be prototyped. Future work will focus on prototypes that benefit the interaction between users and...Schmutz, P., Heinz, S., et al.,. 2009. Cognitive load in ecommerce applications: measurement and effects on user satisfaction. Adv. in Hum.-Comp

  20. Plastic collapse load of corroded steel plates

    Indian Academy of Sciences (India)

    Keywords. Corroded steel plate; plastic collapse; FEM; rough surface. ... The main aim of present work is to study plastic collapse load of corroded steel plates with irregular surfaces under tension. Non-linear finite element method ... Department of Ocean Engineering, AmirKabir University of Technology, 15914 Tehran, Iran ...