WorldWideScience

Sample records for subangular blocky friable

  1. Blocky craters: implications about the lunar megaregolith

    International Nuclear Information System (INIS)

    Thompson, T.W.; Roberts, W.J.; Hartmann, W.K.; Shorthill, R.W.; Zisk, S.H.

    1979-01-01

    Radar, infrared, and photogeologic properties of lunar craters have been studied to determine whether there is a systematic difference in blocky craters between the maria and terrae and whether this difference may be due to a deep megaregolith of pulverized material forming the terra surface, as opposed to a layer of semi-coherent basalt flows forming the mare surface. Some 1310 craters from about 4 to 100 km diameter have been catalogued as radar and/or infrared anomalies. In addition, a study of Apollo Orbital Photography confirmed that the radar and infrared anomalies are correlated with blocky rubble around the crater. Analysis of the radar and infrared data indicated systematic terra-mare differences. Fresh terra craters smaller than 12 km were less likely to be infrared and radar anomalies than comparable mare craters: but terra and mare craters larger than 12 km had similar infrared and radar signatures. Also, there are many terra craters which are radar bright but not infrared anomalies. The authors interpretation of these data is that while the maria are rock layers (basaltic flow units) where craters eject boulder fields, the terrae are covered by relatively pulverized megaregolith at least 2 km deep, where craters eject less rocky rubble. Blocky rubble, either in the form of actual rocks or partly consolidated blocks, contributes to the radar and infrared signatures of the crater. However, aging by impacts rapidly destroys these effects, possibly through burial by secondary debris or by disintegration of the blocks themselves, especially in terra regions. (Auth.)

  2. Partially-Functionalized Isotactic Polystyrene with Blocky Comonomer Segments

    Science.gov (United States)

    Siegel, Ariel; Powers, Wayne; Ryu, Chang Y.

    2012-02-01

    Isotactic polystyrenes (iPSs) have been functionalized in solution, while the accessibility of functionalizing agent is limited by the formation of crystalline domains at various temperatures. The chemical system used is the borylated isotactic polystyrene system, and we investigated the temperature effects on reaction kinetics to ultimately control the blockiness of borylated segments in the resulting copolymer. The chemical composition of partially borylated iPS reaches a steady state that is dependent on temperature. This synthesis has been performed at many different temperatures, with different steady states being reached at different temperatures. Further analysis by differential scanning calorimetry (DSC) has shown that the higher temperature reactions have greater effect on breaking down the crystal lattice structure of the isotactic polystyrene. As a result, the lower temperature reactions affect the crystalline structure less, and the resulting copolymer has more blockiness.

  3. Production of friable embryogenic callus and regeneration of ...

    African Journals Online (AJOL)

    Generation of embryogenic callus is a key step in genetic engineering of many crop species, including cassava. Protocols for generation of friable embryogenic callus (FEC) have been lacking for Ugandan cassava genotypes, thereby delaying their genetic engineering for agronomic and other desirable traits. The objective ...

  4. Blocky inversion of multichannel elastic impedance for elastic parameters

    Science.gov (United States)

    Mozayan, Davoud Karami; Gholami, Ali; Siahkoohi, Hamid Reza

    2018-04-01

    Petrophysical description of reservoirs requires proper knowledge of elastic parameters like P- and S-wave velocities (Vp and Vs) and density (ρ), which can be retrieved from pre-stack seismic data using the concept of elastic impedance (EI). We propose an inversion algorithm which recovers elastic parameters from pre-stack seismic data in two sequential steps. In the first step, using the multichannel blind seismic inversion method (exploited recently for recovering acoustic impedance from post-stack seismic data), high-resolution blocky EI models are obtained directly from partial angle-stacks. Using an efficient total-variation (TV) regularization, each angle-stack is inverted independently in a multichannel form without prior knowledge of the corresponding wavelet. The second step involves inversion of the resulting EI models for elastic parameters. Mathematically, under some assumptions, the EI's are linearly described by the elastic parameters in the logarithm domain. Thus a linear weighted least squares inversion is employed to perform this step. Accuracy of the concept of elastic impedance in predicting reflection coefficients at low and high angles of incidence is compared with that of exact Zoeppritz elastic impedance and the role of low frequency content in the problem is discussed. The performance of the proposed inversion method is tested using synthetic 2D data sets obtained from the Marmousi model and also 2D field data sets. The results confirm the efficiency and accuracy of the proposed method for inversion of pre-stack seismic data.

  5. The FRIABLE1 gene product affects cell adhesion in Arabidopsis.

    Directory of Open Access Journals (Sweden)

    Lutz Neumetzler

    Full Text Available Cell adhesion in plants is mediated predominantly by pectins, a group of complex cell wall associated polysaccharides. An Arabidopsis mutant, friable1 (frb1, was identified through a screen of T-DNA insertion lines that exhibited defective cell adhesion. Interestingly, the frb1 plants displayed both cell and organ dissociations and also ectopic defects in organ separation. The FRB1 gene encodes a Golgi-localized, plant specific protein with only weak sequence similarities to known proteins (DUF246. Unlike other cell adhesion deficient mutants, frb1 mutants do not have reduced levels of adhesion related cell wall polymers, such as pectins. Instead, FRB1 affects the abundance of galactose- and arabinose-containing oligosaccharides in the Golgi. Furthermore, frb1 mutants displayed alteration in pectin methylesterification, cell wall associated extensins and xyloglucan microstructure. We propose that abnormal FRB1 action has pleiotropic consequences on wall architecture, affecting both the extensin and pectin matrices, with consequent changes to the biomechanical properties of the wall and middle lamella, thereby influencing cell-cell adhesion.

  6. Anisotropy of electron work function and reticular compacting of friable faces of metallic crystals

    International Nuclear Information System (INIS)

    Vladimirov, A.F.

    1999-01-01

    The review and statistical estimate of experimental data on work functions for BCC-, FCC- and HCP - metals (W, Mo, Ta, Nb, Cr, V, Ni, Y) as well as the earlier developed quantum-mechanical statistical model of double electrical layer formation at metal surface and the calculation of an electron work function dipole constituent serve as a basis for the development of a semi-empirical theory of electron work function anisotropy. A coefficient of reticular compacting of friable crystal faces is introduced and statistically estimated. A coefficient of crystal emission anisotropy is also introduced and estimated both theoretically and empirically. The theory permits calculating work functions for all crystal faces and a volumetric constituent of the work function from the measured value of electron work function for a single face [ru

  7. Friable but treatable: coronary artery dissections in Ehlers-Danlos syndrome.

    Science.gov (United States)

    Zago, Alexandre C; Matte, Bruno S

    2013-01-01

    Vascular Ehlers-Danlos syndrome is a rare connective tissue disorder associated with arterial dissection or rupture. Percutaneous coronary intervention (PCI) is often critical in patients with this syndrome because their coronary arteries are prone to dissection, enhancing the risk of stent borders dissection when conventional stent deployment pressures are used. Coronary artery bypass graft (CABG) treatment for these patients may also raise concerns because the left internal mammary artery is probably friable. Therefore, coronary artery revascularization in vascular Ehlers-Danlos syndrome either using PCI or CABG is challenging due to the arteries friability. A small number of cases have been published describing the friability of the vessels and associated complications; nevertheless, the optimum treatment remains unclear. We report the case of a 54-year-old woman treated successfully with PCI and CABG in two different acute coronary syndrome episodes, in which specific technical issues related to both procedures were decisive. Copyright © 2011 Wiley Periodicals, Inc.

  8. Quantification of Tremolite in Friable Material Coming from Calabrian Ophiolitic Deposits by Infrared Spectroscopy

    Directory of Open Access Journals (Sweden)

    Antonella Campopiano

    2015-01-01

    Full Text Available The aim of this study is to identify the infrared absorption band suitable for quantifying tremolite in three powdered samples (fine, medium, and large size classes coming from a quarry of ophiolitic friable rocks in the western part of the Calabria region of Italy. Three IR bands were considered: OH stretching band between 3700 and 3650 cm−1, the stretching bands of the Si-O-Si linkage between 1200 and 900 cm−1, and the absorbance band at 756 cm−1 attributable to tremolite. The amount of tremolite in the test samples was quantified by using the curve parameters of the three analytical bands. The quantitative analysis of tremolite using the band due to OH stretchings (3700–3650 cm−1 and the bands attributed to the Si-O-Si stretchings (1200–900 cm−1 showed high values for all test samples. Their use overestimated the tremolite amount because both bands were affected at the interfering mineral silicates such as talc, kaolinite, chlorite, and serpentinites. The abundant presence of antigorite in studied samples mainly in medium size class sample had a key role in our findings. The band at 756 cm−1 was not affected at the interfering minerals and can be used for quantitative analysis of tremolite in sample coming from ophiolitic deposits.

  9. A novel decomposition technique of friable asbestos by CHClF2-decomposed acidic gas

    International Nuclear Information System (INIS)

    Yanagisawa, Kazumichi; Kozawa, Takahiro; Onda, Ayumu; Kanazawa, Masazumi; Shinohara, Junichi; Takanami, Tetsuro; Shiraishi, Masatsugu

    2009-01-01

    Asbestos was widely used in numerous materials and building products due to their desirable properties. It is, however, well known that asbestos inhalation causes health damage and its inexpensive decomposition technique is necessary to be developed for pollution prevention. We report here an innovative decomposition technique of friable asbestos by acidic gas (HF and HCl) generated from the decomposition of CHClF 2 by the reaction with superheated steam at 800 deg. C. Chrysotile-asbestos fibers were completely decomposed to sellaite and magnesium silicofluoride hexahydrate by the reaction with CHClF 2 -decomposed acidic gas at 150 deg. C for 30 min. At high temperatures beyond 400 deg. C, sellaite and hematite were detected in the decomposed product. In addition, crocidolite containing wastes and amosite containing wastes were decomposed at 500 deg. C and 600 deg. C for 30 min, respectively, by CHClF 2 -decomposed acidic gas. The observation of the reaction products by phase-contrast microscopy (PCM) and scanning electron microscopy (SEM) confirmed that the resulting products did not contain any asbestos

  10. Viscoelastic Waves Simulation in a Blocky Medium with Fluid-Saturated Interlayers Using High-Performance Computing

    Science.gov (United States)

    Sadovskii, Vladimir; Sadovskaya, Oxana

    2017-04-01

    A thermodynamically consistent approach to the description of linear and nonlinear wave processes in a blocky medium, which consists of a large number of elastic blocks interacting with each other via pliant interlayers, is proposed. The mechanical properties of interlayers are defined by means of the rheological schemes of different levels of complexity. Elastic interaction between the blocks is considered in the framework of the linear elasticity theory [1]. The effects of viscoelastic shear in the interblock interlayers are taken into consideration using the Pointing-Thomson rheological scheme. The model of an elastic porous material is used in the interlayers, where the pores collapse if an abrupt compressive stress is applied. On the basis of the Biot equations for a fluid-saturated porous medium, a new mathematical model of a blocky medium is worked out, in which the interlayers provide a convective fluid motion due to the external perturbations. The collapse of pores is modeled within the generalized rheological approach, wherein the mechanical properties of a material are simulated using four rheological elements. Three of them are the traditional elastic, viscous and plastic elements, the fourth element is the so-called rigid contact [2], which is used to describe the behavior of materials with different resistance to tension and compression. Thermodynamic consistency of the equations in interlayers with the equations in blocks guarantees fulfillment of the energy conservation law for a blocky medium in a whole, i.e. kinetic and potential energy of the system is the sum of kinetic and potential energies of the blocks and interlayers. As a result of discretization of the equations of the model, robust computational algorithm is constructed, that is stable because of the thermodynamic consistency of the finite difference equations at a discrete level. The splitting method by the spatial variables and the Godunov gap decay scheme are used in the blocks, the

  11. Method for detecting and locating sand-producing zones in friable, unconsolidated sandstone formations of subterranean formations

    International Nuclear Information System (INIS)

    Sparlin, D.D.

    1976-01-01

    A sand-producing zone in a friable, unconsolidated sandstone formation traversed by a well bore is found by first introducing into the reservoir about 0.1--10 gallons of a radioactive mixture per foot of vertical formation being treated, the mixture containing about 0.1--1 lb of radioactive material per gallon of carrier fluid. A dispersing agent containing a deemulsifying surfactant may then be injected into the formation. The radioactivity in the well bore is recorded and the reservoir is returned to production. Another radioactivity log is run and a decrease in radioactivity indicates the location of the sand-producing portions of the formation

  12. Geological and blocky modeling of Qareh Qeshlaq marble deposit in order to optimizing the production planning of quarry

    Directory of Open Access Journals (Sweden)

    Jafar Abdollahi Sharif

    2013-04-01

    Full Text Available Qareh Qeshlaq marble quarry as one of the valuable resources of ornamental stones in West Azarbaijan province formed through thermal carbonate springs while its mineral deposit thickness is limited in comparison with surface extension. In the present research, geological and blocky modeling of the marble deposit was carried out in order to develop a production planning for this quarry, identifying the position of single-marketable-block extracted from it and increasing its economical aspects for exploitation. During the study, in addition to preparing a geological and blocky model for the quarry, firstly the optimum dimensions of its extractable single marketable-block were quantified and then through representing the confining surfaces equation of marble strata in the computer, the optimal maximum dimension and the number and exact location of the single marketable-blocks were determined and presented to the operating team. Based on the findings of these studies and according to the existing 83 exploratory boreholes data, it is possible to extract 183 single marketable-block pink marble and 103 single marketable-block malachite both with 1.5 × 2.5 × 2.5 m raw dimensions while only 2 single marketable-block alabaster layer with 1.3 × 2.5 × 2.5 m dimensions. The results also show that with applying extraction consideration, regarding the productivity coefficient of the layers, and removing the gradual color changes zone, the maximum thickness of the single marketable-blocks for the pink marble, malachite, and alabaster will become 1.65, 1.65 and 1.4 m, respectively.

  13. Comparative study of gamma-ray logging and radiometric core assay of boreholes in block-I of Tummalapalle area, Cuddapah District, Andhra Pradesh using statistical methods

    International Nuclear Information System (INIS)

    Sreenivasa Reddy, M.; Mandal, G.; Bhaumik, B.K.

    2012-01-01

    A comparative study has been carried out between gamma-ray logging and radiometric core assay data of boreholes in Block-I of Tummalapalle area, South Cuddapah Basin, Andhra Pradesh using statistical methods. The product of average grade (in %eU 3 O 8 ) and thickness (in m) of uranium mineralization has been used for this purpose. The outcome of statistical analysis revealed a strong relation between gamma-ray logging and radiometric core assay data. Slope of the line is close to 1.0 and intercept is not different from 0.0. It ensures homogeneity of uranium ore distribution in the host rock. The calculated value from t-test is well within the limit and ensures the negligibility in the difference of means. This indicates that either of the data can be used for ore reserve calculation. (author)

  14. Effect Of Explant Source And Different Medium Culture On Friable Embryogenic Callus Induction Of Four Cultivars Of Cassava Manihot Esculenta Crantz

    Directory of Open Access Journals (Sweden)

    Simplice Prosper Yandia

    2015-08-01

    Full Text Available In order to obtain Friable Embryogenic Callus FEC for protoplast isolation we have evaluated in this research the competance for Friable Embryogenic Callus FEC of four cassava cultivars M61033 Rendre Yalipe and Six-mois in media containing MS supplemented with 8mgl 24-D MS supplemented with 10 mgl BAP and GD supplemented with 12mgl picloram using apical bud AB and immature leaves lobes ILL as explants. In general in the medium GD12mgl picloram the highest efficiencies of FEC ranged from 58 to 87 and the highest score of FEC ranged from 4.2 to 5.4 with explants AB however we have observed with explants ILL the efficiencies of somatic embryos ranged form 41 to 75 and the score ranged from 4.1 to 4.4. The mediums MS28 mgl 24-D have induced with explants AB the efficiencies of FEC ranged from 43 to 57 and the score ranged from 3.1 to 3.8 however with ILL explants the efficiencies of FEC ranged from 39 to 49 and the score ranged from 2.9 to 3.7. The least FEC were observed in the medium MS210 mgl BAP with BA explants however the efficiencies ranged from 6 to 11 and the score ranged from 1.1 to 1.8. Whereas the efficiencies of FEC with ILL explants ranged from 4 to 7 and the score ranged from 0.5 to 0.8. All of four cultivars showed capability of producing FEC although their efficiency varied according to gonotype donors explants and medium taking into acount. Abbreviations GD Gressoff and Doy MS Murashige and Skoog 24-dichloro phenoxyacetic acid BAP Benzylamino-purin-Acid AB Apical Bud ILL Immature Leaves lobes

  15. Estandarización de un protocolo para la obtención de callos friables de borojó (Borojoa patinoi Cuatr. fase I. Optimization of a protocol to obtain friable calli of borojó (Borojoa patinoi Cuatr. phase I.

    Directory of Open Access Journals (Sweden)

    Martínez D. Mauricio

    2007-12-01

    Full Text Available Se investigó la influencia de los reguladores de crecimiento para la obtención de callos friables en borojó (Borojoa patinoi Cuatr. El material vegetal utilizado se obtuvo de árboles en producción ubicados en el Municipio de San Luis, Antioquia, Colombia. Las semillas se desinfectaron con hipoclorito de sodio al 3% por 25 min más etanol al 70% por 15 min con la adición de dos gotas de Tween 20. Para los diferentes tratamientos se utilizaron como explantes hojas jóvenes obtenidas in vitro a partir de semilla, las cuales se cultivaron en el medio MS (1962 suplementado con 2,4-D en combinación con BAP y TDZ, sin obtener respuesta favorable para la obtención de callo friable entre el día 15 al 45 después de iniciado el cultivo. Sin embargo, se realizó otro ensayo con el mismo explante en el medio de cultivo MS (1962 con la adición de 1 mg/L de 2-4 D, como medio para la iniciación de embriogénesis, observándose a los 45 días la formación de callos friables y de color amarillo-verde. Este trabajo es un informe parcial de un macroproyecto sobre la optimización de un protocolo para la obtención de metabolitos secundarios de interés comercial mediante la utilización de suspensiones celulares de Borojoa patinoi.The influence of growth regulators to obtain friable calli in borojo (Borojoa patinoi Cuatr was investigated. The used vegetable material was obtained from productive trees located in the town of San Luis, Antioquia, Colombia. Seeds were disinfected with 3% sodium hypochlorite for 20 minutes, plus 70% ethanol for 15 minutes with the addition of two tween 20 drops. In the different experiments, young leaves obtained in vitro from seeds were used as explants. They were cultivated in the MS medium supplemented with 2,4-D and combined with BAP and TDZ. No positive response related to the obtaining of friable callus was shown between the days 15 to 45. However, another test was carried out with the same explants in the MS medium

  16. Embriogénesis somática y producción de callo embriogénico friable de dos cultivares de yuca (Manihot esculenta Crantz

    Directory of Open Access Journals (Sweden)

    Juan Camilo Ochoa

    2012-07-01

    Full Text Available Título en ingles: Somatic Embryogenesis and friable embryogenic callus production in two cassava cultivars (Manihot esculenta Crantz Resumen: La yuca (Manihot esculenta Crantz es un cultivo de alta importancia en países tropicales. La transformación genética de yuca ha sido posible desde hace 15 años mediante la producción que callo embriogénico friable (CEF a partir de embriones somáticos. En el presente trabajo se evalúan la inducción de embriones somáticos usando tres diferentes auxinas sintéticas y la producción de CEF a partir de éstos en los cultivares de yuca SG107-35 y BRA685. Estos cultivares son resistentes a la bacteriosis vascular de yuca cuyo agente causal es Xanthomonas axonopodis pv. manihotis, una de las principales limitantes del cultivo. Los resultados obtenidos muestran que en ambos cultivares la hormona Picloram a una concentración de 12 mg/l fue más eficiente que 2,4-D y Dicamba para producir embriones somáticos. Adicionalmente se consiguió la producción de CEF y la regeneración de plantas mediante embriogénesis somática en el cultivar BRA685. Los resultados del presente trabajo son importantes para evaluar la transformabilidad de distintos cultivares de yuca. Actualmente este número es bastante reducido principalmente porque la producción de CEF es fuertemente influenciada por el genotipo. Por tal razón solo se transforma de manera rutinaria y eficiente en el cultivar 60444. La posibilidad de transformación de distintos cultivares de yuca permitirá explotar la enorme variabilidad del cultivo, invitándonos a aumentar los esfuerzos para mejorar y universalizar los protocolos de transformación de yuca. Palabras clave: Picloram, regeneración, dependencia del genotipo.  Abstract: The cassava (Manihot esculenta Crantz crop has a very important role as a food, feed and a raw material in developing countries; therefore it is a priority to develop technologies oriented to the solution of problems and

  17. Characterization and Classification of Soils on an Agricultural ...

    African Journals Online (AJOL)

    subangular blocky in the surface and changes to angular blocky in .... have angular blocky structure at the surface and changes to ... The soils in TUP 3 were brown in colour (2.5YR 4/6) in ..... erosion and enhance and maintain soil quality and.

  18. Indução de calos friáveis em explantes foliares de Salix (Salyx humboldtiana Willd Induction of friable callus in leaf explants of Salix (Salyx humboldtiana Willd

    Directory of Open Access Journals (Sweden)

    Breno Régis Santos

    2005-06-01

    Full Text Available O salix é uma árvore ornamental adaptada a terrenos úmidos, sendo considerada uma espécie importante para a recomposição de áreas ciliares degradadas. A madeira pode ser empregada na indústria em geral. Apesar de produzir grande quantidade de sementes, estas não possuem alta percentagem de germinação. O presente trabalho teve como objetivo realizar o estabelecimento in vitro de salix através da indução e formação de calos friáveis em explantes foliares, visando a uma posterior regeneração de plantas para a propagação massal desta espécie. Explantes foliares foram inoculados em meio de cultura MS (MURASHIGE & SKOOG, 1962, acrescido de diferentes concentrações de ácido 2,4-diclorofenoxiacético (0; 1,0; 2,0; 4,0; 6,0; 8,0; 10,0 e 12,0mg L-1 e combinações entre ácido naftalenoacético e benzilaminopurina, ambos em concentrações de 0,0; 1,0; 2,0; 4,0; 6,0 e 8,0mg L-1. Os resultados demonstram que explantes inoculados na ausência de reguladores de crescimento não apresentam a formação de calos friáveis. Significativa produção de calos friáveis (90% é obtida utilizando-se 6,0mg L-1 de ácido 2,4-diclorofenoxiacético. A utilização de concentração individual de ácido naftalenoacético ou benzilaminopurina, além de induzir a calogênese também foi capaz de promover rizogênese.Salix is an ornamental tree adapted to humid soils being considered an important species used in depleted areas. Its wood may be used in all kinds of industries. Although the production of seeds is large, the germination is reduced. The objective of this work was to establish salix in vitro through the induction and formation of friable callus of leaf explants to provide future regeneration of plants for mass propagation of the species. Leaf explants were inoculated in MS medium (MURASHIGE & SKOOG, 1962 supplemented with different concentrations of 2-4-diclorofenoxiacetic acid (0; 1.0; 2.0; 4.0; 6.0; 8.0 and 12.0mg L-1 and combinations

  19. Production of friable embryogenic callus and regeneration of ...

    African Journals Online (AJOL)

    sunny t

    2015-06-03

    Jun 3, 2015 ... Generation of embryogenic callus is a key step in genetic engineering of many crop species, including cassava. ... CBSD is caused by two Ipomovirus; Cassava .... through a 1 mm2 pore-sized steel wire mesh using a spatula.

  20. Effect of Sequence Blockiness on the Morphologies of Surface-grafted Elastin-like Polypeptides

    Science.gov (United States)

    Albert, Julie; Sintavanon, Kornkanok; Mays, Robin; MacEwan, Sarah; Chilkoti, Ashutosh; Genzer, Jan

    2014-03-01

    The inter- and intra- molecular interactions among monomeric units of copolymers and polypeptides depend strongly on monomer sequence distribution and dictate the phase behavior of these species both in solution and on surfaces. To study the relationship between sequence and phase behavior, we have designed a series of elastin-like polypeptides (ELPs) with controlled monomer sequences that mimic copolymers with various co-monomer sequence distributions and attached them covalently to silicon substrates from buffer solutions at temperatures below and above the bulk ELPs' lower critical solution temperatures (LCSTs). The dependence of ELP grafting density on solution temperature was examined by ellipsometry and the resultant surface morphologies were examined in air and under water with atomic force microscopy. Depositions performed above the LCST resulted in higher grafting densities and greater surface roughness of ELPs relative to depositions carried out below the LCST. In addition, we are using gradient substrates to examine the effect of ELP grafting density on temperature responsiveness.

  1. Experimental equipment for cutting friable marl layers. Probni uredjaj za sjecenje laporovito krtih stijena (laporaca)

    Energy Technology Data Exchange (ETDEWEB)

    Kljucanin, T.; Sejdinovic, A.; Miskic, D.; Tumenko, D. (Rudarski Institut, Tuzla (Yugoslavia))

    1990-01-01

    Describes the design of an experimental rock cutter to be attached to shovel excavators working on benches of surface mines. Pilot testing of the cutter will be carried out in marlstone overburden of the Banovici and Djurdjevik surface coal mines (Yugoslavia). The cutter is attached to the boom of a shovel excavator. Main components of the cutter are a frame with 3 hydraulic drills and hydraulic wedges. The 3 hydraulic drills are mounted on the frame in a line and spaced at 1.2 m. Borehole diameter is 150 mm. Metal wedges are hydraulically driven into the boreholes to slice the rock. The cutter is regarded as an alternative to the blasting of rock inclusions in overburden strata. 2 refs.

  2. Minesoil development in central West Virginia

    International Nuclear Information System (INIS)

    Noll, W.J.; Sencindiver, J.C.

    1998-01-01

    Immediately after mining and regrading, minesoils usually have little or no horizon development. Over time, horizons begin to form and definite diagnostic properties develop. The purpose of this study was to document the genesis of a 13-year-old minesoil. The study site was a reclaimed surface mine in Upshur County, West Virginia. Transects were established in 1983 across the site immediately after mining and regrading but before revegetation. Soil pits were excavated to 100+ cm at nine points along those transects. Soil profiles were described at each point, and each minesoil horizon was sampled for analyses. In 1983, only C horizons were described because no structure had developed. In 1996, all nine profiles had developed A horizons ranging in thickness from 2 to 9 cm (mean 6.1 cm). Subsurface horizons (AC, Bw, or C/B), ranging in thickness from 7 to 17 cm (mean 11.8 cm), also had formed in each profile. The A horizons were identified by colors that were darker than the subsoil horizons and the presence of weak fine granular or subangular blocky structure. The AC, Bw and C/B horizons had weak fine to very coarse subangular blocky or weak medium to very thick platy structure. Chemical and physical properties of the minesoils supported the morphological properties indicating that definite pedogenic horizons have formed in 13 years

  3. Assessment the effect of homogenized soil on soil hydraulic properties and soil water transport

    Science.gov (United States)

    Mohawesh, O.; Janssen, M.; Maaitah, O.; Lennartz, B.

    2017-09-01

    Soil hydraulic properties play a crucial role in simulating water flow and contaminant transport. Soil hydraulic properties are commonly measured using homogenized soil samples. However, soil structure has a significant effect on the soil ability to retain and to conduct water, particularly in aggregated soils. In order to determine the effect of soil homogenization on soil hydraulic properties and soil water transport, undisturbed soil samples were carefully collected. Five different soil structures were identified: Angular-blocky, Crumble, Angular-blocky (different soil texture), Granular, and subangular-blocky. The soil hydraulic properties were determined for undisturbed and homogenized soil samples for each soil structure. The soil hydraulic properties were used to model soil water transport using HYDRUS-1D.The homogenized soil samples showed a significant increase in wide pores (wCP) and a decrease in narrow pores (nCP). The wCP increased by 95.6, 141.2, 391.6, 3.9, 261.3%, and nCP decreased by 69.5, 10.5, 33.8, 72.7, and 39.3% for homogenized soil samples compared to undisturbed soil samples. The soil water retention curves exhibited a significant decrease in water holding capacity for homogenized soil samples compared with the undisturbed soil samples. The homogenized soil samples showed also a decrease in soil hydraulic conductivity. The simulated results showed that water movement and distribution were affected by soil homogenizing. Moreover, soil homogenizing affected soil hydraulic properties and soil water transport. However, field studies are being needed to find the effect of these differences on water, chemical, and pollutant transport under several scenarios.

  4. Characterization and classification of two soils derived from basic rocks in Pernambuco State Coast, Northeast Brazil

    Directory of Open Access Journals (Sweden)

    Oliveira Lindomário Barros de

    2004-01-01

    Full Text Available Geomorphic surfaces that present soils derived from basic rocks under warm and humid climate are unique scenarios for studying tropical soils. This paper aimed to characterize and classify two pedons derived from basalt at the Atlantic Forest Zone, Pernambuco State, Northeastern coast of Brazil. Two representative pedons (P1 and P2 were selected on a hillslope at the Cabo de Santo Agostinho municipality. Field macromorphological descriptions were carried out and soil horizon were sampled for physical, chemical, mineralogical and micromorphological characterization. The soils were classified, according to the Brazilian System of Soil Classification (and US Soil Taxonomy as: "Latossolo Vermelho-Amarelo distroférrico argissólico" (Typic Hapludox (P1 and "Nitossolo Vermelho distroférrico típico" (Rhodic Paleudult (P2. Pedon 1 differs from Pedon 2 in some aspects. For instance, P1 presents more yellowish colors, absence of clay illuviation, more friable consistence and the prismatic structure undergoes transformation to angular and subangular blocks. Pedon 2 presents ferri-argilans and leptocutans which indicate that vertical and lateral illuviation of clay is an active process in their formation. These chemically poor and mineralogically uniform soils are a result of the high temperature and rainfall of the studied area.

  5. Soil of the lower valley of the Dragonja river (Slovenia

    Directory of Open Access Journals (Sweden)

    Tomaž PRUS

    2015-11-01

    Full Text Available Soil of the lower valley of the river Dragonja developed under specific soil-forming factors. Soil development in the area was influenced by alluvial sediments originating from surrounding hills, mostly of flysch sequence rocks, as a parent material, Sub-Mediterranean climate and the vicinity of the sea. Different soil classification units (Gleysol and Fluvisol were proposed for that soil in previous researches. The aim of our study was the evaluation of morphological, chemical and mineralogical characteristics of soil, based on detailed soil description and analyses, and to define the appropriate soil classification units. Field examinations revealed that the soil had a stable blocky or subangular structure and did not express substantial hydromorphic forms. Soil pH value was ranging from 6.9 to 7.5. In most locations electroconductivity (ECe did not exceed 2 ds/m. Base saturation was high (up to 99 %, with a majority of Ca2+ ions. Exchangeable sodium percentage (ESP was ranging from 0.2 to 3.8 %, which is higher compared to other Slovenian soils but does not pose a risk to soil structure. Soil has silty clay loam texture with up to 66 % of silt. Prevailing minerals were quartz, calcite and muscovite/illite. No presence of swelling clay mineral montmorillonite was detected. According to Slovenian soil classification, we classified the examined soil as alluvial soil. According to WRB soil classification, the soil was classified as Cambisol.

  6. Micromorphology and stable-isotope geochemistry of historical pedogenic siderite formed in PAH-contaminated alluvial clay soils, Tennessee, U.S.A

    Science.gov (United States)

    Driese, S.G.; Ludvigson, Greg A.; Roberts, J.A.; Fowle, D.A.; Gonzalez, Luis A.; Smith, J.J.; Vulava, V.M.; McKay, L.D.

    2010-01-01

    Alluvial clay soil samples from six boreholes advanced to depths of 400-450 cm (top of limestone bedrock) from the Chattanooga Coke Plant (CCP) site were examined micromorphologically and geochemically in order to determine if pedogenic siderite (FeCO3) was present and whether siderite occurrence was related to organic contaminant distribution. Samples from shallow depths were generally more heavily contaminated with polycyclic aromatic hydrocarbons (PAHs) than those at greater depth. The upper 1 m in most boreholes consisted of mixtures of anthropogenically remolded clay soil fill containing coal clinker, cinder grains, and limestone gravel; most layers of coarse fill were impregnated with creosote and coal tar. Most undisturbed soil (below 1 m depth) consisted of highly structured clays exhibiting fine subangular blocky ped structures, as well as redox-related features. Pedogenic siderite was abundant in the upper 2 m of most cores and in demonstrably historical (< 100 years old) soil matrices. Two morphologies were identified: (1) sphaerosiderite crystal spherulites ranging from 10 to 200 um in diameter, and (2) coccoid siderite comprising grape-like "clusters" of crystals 5-20 ??n in diameter. The siderite, formed in both macropores and within fine-grained clay matrices, indicates development of localized anaerobic, low-Eh conditions, possibly due to microbial degradation of organic contaminants. Stable-isotope compositions of the siderite have ??13C values spanning over 25%o (+7 to - 18%o VPDB) indicating fractionation of DIC by multiple microbial metabolic pathways, but with relatively constant ??18O values from (-4.8 ?? 0.66%o VPDB) defining a meteoric sphaerosiderite line (MSL). Calculated isotope equilibrium water ??18O values from pedogenic siderites at the CCP site are from 1 to 5 per mil lighter than the groundwater ??18O values that we estimate for the site. If confirmed by field studies in progress, this observation might call for a reevaluation of

  7. Evaluation of soil fertility status of Regional Agricultural Research Station, Tarahara, Sunsari, Nepal

    Directory of Open Access Journals (Sweden)

    Dinesh Khadka

    2017-10-01

    Full Text Available Soil fertility evaluation of an area or region is most basic decision making tool for the sustainable soil nutrient management. In order to evaluate the soil fertility status of the Regional Agricultural Research Station (RARS, Tarahara, Susari, Nepal. Using soil sampling auger 81 soil samples (0-20 cm were collected based on the variability of land. The collected samples were analyzed for their texture, structure, colour, pH, OM, N, P2O5, K2O, Ca, Mg, S, B, Fe, Zn, Cu and Mn status. The Arc-GIS 10.1 software was used for the preparation of soil fertility maps. The soil structure was granular to sub-angular blocky and varied between brown- dark grayish brown and dark gray in colour. The sand, silt and clay content were 30.32±1.4%, 48.92±0.89% and 20.76±0.92%, respectively and categorized as loam, clay loam, sandy loam, silt loam and silty clay loam in texture. The soil was moderately acidic in pH (5.98±0.08. The available sulphur (2.15±0.21 ppm, available boron (0.08±0.01 ppm and available zinc (0.35±0.03 ppm status were very low, whereas extractable magnesium (44.33±6.03 ppm showed low status. Similarly, organic matter (2.80±0.07%, total nitrogen (0.09±0.004 %, extractable calcium (1827.90±45.80 ppm and available copper (1.15±0.04 ppm were medium in content. The available phosphorus (39.77±5.27 ppm, extractable potassium (134.12±4.91 ppm, and available manganese (18.15±1.15 ppm exhibits high status, while available iron (244.7±19.70 ppm was very high. The fertilizer recommendation can be done based on determined soil fertility status to economize crop production. Furthermore, research farm should develop future research strategy accordance with the prepared soil data base.

  8. Assessment of soil fertility status of Agriculture Research Station, Belachapi, Dhanusha, Nepal

    Directory of Open Access Journals (Sweden)

    Dinesh Khadka

    2016-12-01

    Full Text Available Soil test-based fertility management is important for sustainable soil management. This study was carried out to determine the soil fertility status of the Agriculture Research Station, Belachapi, Dhanusha, Nepal. Using soil sampling auger 25 soil samples were collected randomly from a depth of 0-20 cm. Soil sampling points were identified using GPS device. Following standard methods adopted by Soil Science Division laboratory, Khumaltar, the collected soil samples were analyzed to find out their texture, pH, N, P2O5, K2O, Ca, Mg, S, B, Fe, Zn, Cu, Mn and organic matter status. The soil fertility status maps were made using Arc-GIS 10.1 software. The observed data revealed that soil was grayish brown in colour and sub-angular blocky in structure. The sand, silt and clay content were 36.03±3.66%, 50.32±2.52% and 25.42±2.25%, respectively and categorized as eight different classes of texture. The soil was acidic in pH (5.61±0.14. The available sulphur (0.73±0.09 ppm status was very low, whereas organic matter (1.34±0.07%, available boron (0.56±0.10 ppm, available zinc (0.54±0.22 ppm and available copper (0.30±0.01 ppm were low in status. The extractable potassium (95.52±13.37 ppm and extractable calcium (1264.8±92.80ppm exhibited medium in status. In addition, available phosphorus (33.25±6.97 ppm, available magnesium (223.20±23.65 ppm and available manganese (20.50±2.43 ppm were high in status. Furthermore, available iron (55.80±8.89 ppm status was very high. To improve the potentiality of crops (maize, rice, wheat etc. for studied area, future research strategy should be made based on its soil fertility status.

  9. Selected Properties and Systematic Position of Soils Developed from Red Sandstones and Clays of the Lower Triassic Buntsandstein in the Nw Part of the Holy Cross Mountains (Poland / Niektóre właściwości i pozycja systematyczna gleb wytworzonych z czerwonych piaskowców i iłów dolnego triasu w NW obrzeżeniu Gór Świętokrzyskich

    Directory of Open Access Journals (Sweden)

    Zagórski Zbigniew

    2015-09-01

    Full Text Available The aim of the study was to compare the properties of soils developed from the Lower Triassic Buntsandstein sediments in the north-western part of the Holy Cross Mountains (Poland. These are deposits of continental genesis and unique features such as red beds. Two representative soil pedons - the Bartków profile (pBK developed from clay and the Góra Czerwona profile (pGC developed from sandstone were selected for detailed analyzes. The morphology of profiles, their micromorphological features, mineralogical composition, and physico-chemical properties were examined. Most of the properties of the soils are a consequence of the original parent rock lithology. A specific feature of the morphology of the soils are the presence of red color (about 10R by the Munsell color scale related to the presence of hematite. As shown by the XRD data, hematite is not the product of the current soil-forming processes, but it is a lithogenic component, which was inherited from the parent rock. Under the influence of climatic factors primary rock structure has been transformed into a new pedogenic one. Soils developed from clays have a characteristic angular blocky structure. Micromorphological analysis showed that an important role in the formation of soil structure involves geogenic susceptibility of Triassic clays to specific cuboid disintegration. This is indicated by the pore system of planes as an orthogonal nets visible in thin section. The soils developed from sandstone have a weak (unstable subangular blocky structure. The main reason is the insufficient dispersion of the clay-ferruginous fraction from the sandstone matrix. Microscopic observations indicate that fine factions occurs as loose microaggregates, which results in a feature that smaller rock fragments and individual quartz grains are not bonded into soil aggregates. The studied soils are characterized by specific physical-chemical properties. Some of them strongly depend on the mineralogical

  10. Soil micromorphogenesis and Early Holocene paleoclimate at the desert margin of Southern Arabia Micromorfoedafogénesis y paleoclima del Holoceno Inferior en el márgen desértico del sur de Arabia Micromorfogénese do solo e paleoclima inicial do Holoceno na margem deserta do Sul da Arábia

    Directory of Open Access Journals (Sweden)

    Peter Kühn

    2013-07-01

    Full Text Available The Ramlat as-Sab'atayn desert margin near Ma'rib, Yemen, displays well-preserved Early Holocene paleosols that are documented by micromorphological and pedological data. The buried soils, which are represented by Ahb horizons, indicate soil formation mostly before 8.3 cal ka BP. In contrast, sandy cover sediments without signs of pedogenesis appeared between 8.3 and 6.6 cal ka BP due to increasing aridity. Characteristic micromorphological features of the cover sediments are a single grain microstructure, crystallitic b-fabric, predominant occurrence of fresh sideromelane, and remnants of microlayers. Micromorphological pedogenic features in the buried Ah horizons include a subangular blocky microstructure, undifferentiated b-fabric as a result of enrichment of organic matter and decalcification, and the predominant occurrence of completely altered sideromelane. Most of these horizons appeared to be nearly completely decalcified so that in parts a stipple speckled b-fabric and neoformed clay coatings could be detected as a result of stronger weathering and soil formation. Pedogenic data provide important information about Holocene climate fluctuations, including the amount of precipitation, which was calculated on the basis of geochemical data from buried A, AB and B horizons. The buried paleosols represent moist climate conditions with precipitation ranging from 400 to 600 mm a-1.En los márgenes del desierto Ramlat as-Sab'atayn, cerca de Ma'rib (Yemen, se encuentran paleosuelos del Holoceno Inferior bien conservados que se documentan con datos micromorfológicos y edáficos. Los suelos enterrados, representados por horizontes Ahb, indican que se formaron mayoritariamente antes de hace 8,3 ka. Por el contrario, los sedimentos arenosos que los cubren sin rasgos de edafogénesis se depositaron posteriormente debido a una aridez creciente hasta hace 6,6 ka. Los rasgos micromorfológicos de los sedimentos arenosos están caracterizados por una

  11. Soil physical land degradation processes

    Science.gov (United States)

    Horn, Rainer

    2017-04-01

    According to the European Soil Framework Directive (2006) soil compaction is besides water and wind erosion one of the main physical reasons and threats of soil degradation. It is estimated, that 32% of the subsoils in Europe are highly degraded and 18% moderately vulnerable to compaction. The problem is not limited to crop land or forest areas (especially because of non-site adjusted harvesting machines) but is also prevalent in rangelands and grassland, and even in so called natural non-disturbed systems. The main reasons for an intense increase in compacted agricultural or forested regions are the still increasing masses of the machines as well the increased frequency of wheeling under non favorable site conditions. Shear and vibration induced soil deformation enhances the deterioration of soil properties especially if the soil water content is very high and the internal soil strength very low. The same is true for animal trampling in combination with overgrazing of moist to wet pastures which subsequently causes a denser (i.e. reduced proportion of coarse pores with smaller continuity) but still structured soil horizons and will finally end in a compacted platy structure. In combination with high water content and shearing due to trampling therefore results in a complete muddy homogeneous soil with no structure at all. (Krümmelbein et al. 2013) Site managements of arable, forestry or horticulture soils requires a sufficiently rigid pore system which guarantees water, gas and heat exchange, nutrient transport and adsorption as well as an optimal rootability in order to avoid subsoil compaction. Such pore system also guarantees a sufficient microbial activity and composition in order to also decompose the plant etc. debris. It is therefore essential that well structured horizons dominate in soils with at best subangular blocky structure or in the top A- horizons a crumbly structure due to biological activity. In contrast defines the formation of a platy

  12. Assessment of genetic diversity in tomato for fruit morphology, composition and yield

    International Nuclear Information System (INIS)

    Zaif, K.; Amjad, M.; Saeed, A.

    2016-01-01

    Postharvest losses are of great concern in vegetable crops, including tomato, due to their perishable nature. Damage to tomato fruit during transportation is related to its shape besides other factors. Therefore, this study was conducted to assess genetic diversity in the available tomato germplasm (35 genotypes) for fruit morphology, biochemical composition and yield. Considerable variation was observed for all studied traits except number of locules per fruit, TSS and reducing sugars, for which very low range was recorded. While, moderate level of variation existed for stem-end blockiness, blossom-end blockiness and elongated shape which suggested that fruit of most of the varieties could belong to more than one category of fruit shape. Fruit length and diameter had significantly positive correlation with heart shape of tomato, while later was also correlated with blossom-end-blockiness. Heart shape of tomato fruit was also correlated with stem-end blockiness. Yield showed significantly positive correlation with number of inflorescence per plant. Principal component analysis (PCA) revealed PC-I to PC-VI had Eigen values >1, which contributed 73.86% of total variability for different traits. The highest factor loading values for blossom-end-blockiness, stem-end-blockiness, heart shape and elongated shape was recorded in PC-6, PC-4, PC-6 and PC-2, respectively. Thirty five genotypes were grouped into three clusters. Higher yield and stem-end-blockiness was observed in genotypes from cluster II, while higher values for blossom-end-blockiness, heart shape and elongated shape were noticed in cluster I followed by cluster III. So, it can be assumed that genotypes in cluster II showed higher yield and also possessed blocky fruit, a desirable character for transportation and processing purpose. Moreover, it is suggested that genotypes of cluster I and cluster II can be crossed to find heterosis for yield and fruit shape related traits. (author)

  13. the use of statistical grain-size method in analysing borehole

    African Journals Online (AJOL)

    of medium-coarse grained sandstones, sub-angular to sub-rounded ... rainy season. Figure 1: Nsukka section of the Nsukka-Okigwe Cuesta. 6 0. 8 0. 100. 120. 140 ...... and also to improve the quality of drinking water, several boreholes were ...

  14. INTRODUCTION Sandstone beds within Auchi locality are the ...

    African Journals Online (AJOL)

    The major framework composition is Q F L which classifies the sandstone as Quartz ... The grains are texturally immature as depicted by their subangular edges but mineralogically ..... Fig 6 : Vertical Section of Bioturbated Sandstone Lithofacies Showing Trace Fossils ..... on Water Quality and Planktonic Production in an.

  15. Coarse fraction components in a red-clay sedimemt core, Central Indian Ocean Basin: Their occurrence and significance

    Digital Repository Service at National Institute of Oceanography (India)

    Iyer, S.D.; Fernandes, G.Q.; Mahender, K.

    -spherical shapes while some grains are irregular or blocky. Iron-rich fragments are nearly triangular or blocky and are 224 to 735 µm long (Fig. 8 A,B). Pumices of different shapes are 183 to 850 µm in size (Fig. 8 C-F) and sometimes have FeMn oxides.... 7 C,D). The former are 227 to 411 µm long and are either platy or bubble or Y-shaped morphology while the translucent shards are 46 to 190 µm long and are blocky or flat and stubby (Fig. 7 E,F). Coloured glass is also present of spherical to sub...

  16. Native valve endocarditis due to Candida parapsilosis in an adult ...

    African Journals Online (AJOL)

    . Blood cultures were positive for C. parapsilosis. β-D-glucan assay levels were elevated. An echocardiogram showed large, friable vegetations on the mitral valve. C. parapsilosis was cultured from the haemodialysis tip and the vegetations.

  17. Remote sensing and aerial photography for coastal geomorphology

    Digital Repository Service at National Institute of Oceanography (India)

    Wagle, B.G.

    composition as the loose beach sand. It is friable to well cemented rock consisting of mineral grains,; rock fragments and calcareous debris,cemented by calcium carbonate. It is formed only in the intertidal zone or spray zone. Beach Ridges...

  18. Type I fitting of copper tubes from a water distribution system

    CSIR Research Space (South Africa)

    Fernandes, PJL

    1998-03-01

    Full Text Available with a greenish scale of a copper compound called malachite. Beneath this scale, the tube surface is covered with a smooth, shiny layer of dark cuprite which is very friable and easily spalled off. Pits are usually...

  19. Diagenetic Changes in Common Hot Spring Microfacies

    Science.gov (United States)

    Hinman, N. W.; Kendall, T. A.; MacKenzie, L. A.; Cady, S. D.

    2016-05-01

    The friable nature of silica hot spring deposits makes them susceptible to mechanical weathering. Rapid diagenesis must take place for these rocks to persist in the geologic record. The properties of two microfacies at two deposits were compared.

  20. The efficiency of the use of penetration nuclear logging in hydrogeology and engineering geology

    International Nuclear Information System (INIS)

    Ferronsky, V.I.

    1992-01-01

    The latest developments in equipment and techniques for nuclear and combined non-nuclear logging in friable unconsolidated deposits, including marine bottom sediments are described. The effectiveness of these techniques in hydrogeological and engineering geological investigations is discussed. (Author)

  1. Establishment of sorghum cell suspension culture system for ...

    African Journals Online (AJOL)

    STORAGESEVER

    2008-03-18

    Mar 18, 2008 ... Additionally, sorghum cell suspension cultures have been initiated from the friable ... proteomics technologies. The field of proteomics is .... air dried at room temperature and resuspended in 2 ml of urea buffer [9 M urea, 2 M ...

  2. A new high temperature resistant glass–ceramic coating for gas ...

    Indian Academy of Sciences (India)

    Unknown

    resultant coatings showed presence of a number of microcrystalline phases. SEM micrographs ... processing of two novel glass–ceramic coating materials, ... stainless steel tray to yield frit (a friable glassy material). .... Frit (– 20 mesh) powder.

  3. Poor man medical pneumoplasty: Bronchoscopic lung volume reduction with hot saline versus dissolved doxycycline as a neoteric remedy of pulmonary emphysema

    Directory of Open Access Journals (Sweden)

    A.M. Abumossalam

    2016-01-01

    Conclusion: Bronchoscopic lung volume reduction by hot saline and dissolved doxycycline comes into sight to be a safe and feasible profile with an acceptable outcome that presents an attractive substitute to COPD patients who are physiologically friable.

  4. Properties of Soils in River Katsina-Ala Catchments Area, Benue ...

    African Journals Online (AJOL)

    soil. The surface soil had granular structure, which changed to transited medium blocky and angular structure with depth while the horizons were generally massive. The CEC, organic carbon, Organic matter, total phosphorus (Bray I) and total ...

  5. A Combined First and Second Order Variational Approach for Image Reconstruction

    KAUST Repository

    Papafitsoros, K.; Schö nlieb, C. B.

    2013-01-01

    the creation of undesirable artifacts and blocky-like structures in the reconstructed images-a known disadvantage of the ROF model-while being simple and efficiently numerically solvable. ©Springer Science+Business Media New York 2013.

  6. Monte Carlo study of holding forces for tank cars on grades

    Science.gov (United States)

    2013-04-15

    This paper describes a numerical procedure to examine the holding forces needed to secure a cut of railroad tank cars staged on a grade during loading and unloading operations. Holding forces are created by applying emergency brake systems and blocki...

  7. An evaluation of the lamb and mutton carcase grading system in the ...

    African Journals Online (AJOL)

    formation traits such as short in the leg, plumpness and blockiness indicate more meat, ..... partment of Agriculture and Water Supply. References ... Granada. Publishing: London. KEMPTHORNE, D., 1969. An introduction to genetic. Statistics.

  8. Luna 24 regolith breccias: A possible source of the fine size material of the Luna 24 regolith

    Science.gov (United States)

    Rode, O. D.; Lindstrom, M. M.

    1994-01-01

    The regolith breccias from the Luna 24 core were analyzed. The Luna 24 regolith is a mixture of fine and coarse grain materials. The comparable analysis of the grain size distributions, the modal and chemical compositions of the breccias, and the regolith from the same levels show that the friable slightly litificated breccia with a friable fine grain matrix may be a source of fine grain material of the Luna 24 present day regolith.

  9. Malignant mixed Mullerian tumour of the prolapsed cervix: A case ...

    African Journals Online (AJOL)

    ... which was ulcerated, friable, and bled easily on touch. Impression was grade three uterine prolapse with infected cervical polyp/ cervical sarcoma. Excision of the tumour through trans-vaginal hysterectomy was performed, no lymphadenopathy was found, no adnexa abnormalities, and no involvement of the vaginal wall.

  10. Single-catheter approach for ablation of the slow pathway in a patient with type IV Ehlers-Danlos syndrome and AV nodal reentrant tachycardia using a magnetic navigation system

    NARCIS (Netherlands)

    T. Szili-Torok (Tamas); E. Jessurun; L.J.L.M. Jordaens (Luc)

    2008-01-01

    textabstractPatients with Ehlers-Danlos syndrome type IV have thin-walled, friable arteries and veins. Invasive procedures carry a significantly increased risk for perforation of blood vessels. The aim of this case report is to demonstrate the feasibility and potential benefits of using a

  11. Production of the first transgenic cassava in Africa via direct shoot ...

    African Journals Online (AJOL)

    Here we report on the first successful establishment of cassava regeneration and transformation capacity in Africa via organogenesis, somatic embryogenesis and friable embryogenic callus (FEC). As a prerequisite for genetic engineering, we evaluated six African cassava genotypes for the ability of a) induction of FEC b) ...

  12. Development and Evaluation of Praziquantel Solid Dispersions in ...

    African Journals Online (AJOL)

    Mucoadhesion properties of the SD (1:3) and SSG, on mucin disks were examined .... the SD mass was sufficiently friable to be ground ... Figure 1: Solubility of pure PZQ, PM and SD in water ... particles also presented filamentous shape and.

  13. St. Regis Paper Mill: Architectural and Environmental Survey

    Science.gov (United States)

    2010-02-01

    also be used to whiten the fibers. Caustic soda along with chlorine is used to wash the pulp of impurities and also con- tributes to bleaching...about soldier health than a desire to not complicate clean-up re- sponsibility. Table 1. Locations of friable asbestos. LOCATION AREA ASBESTOS TYPE

  14. 40 CFR Appendix A to Subpart M of... - Interpretive Rule Governing Roof Removal Operations

    Science.gov (United States)

    2010-07-01

    ...-containing material (ACM) is material containing more than one percent asbestos as determined using the... NESHAP classifies ACM as either “friable” or “nonfriable”. Friable ACM is ACM that, when dry, can be crumbled, pulverized or reduced to powder by hand pressure. Nonfriable ACM is ACM that, when dry, cannot be...

  15. Proceedings from the Annual Army Environmental R&D Symposium (16th) Held 23-25 June 1992 at Fort Magruder Inn and Conference Center, Williamsburg, Virginia

    Science.gov (United States)

    1992-06-01

    photoactivity. The second prong was to evaluate the perovskite materials to utilize the lattice oxygen for the oxidation step and was found unsuccessful...Loalized 0 Distributed (*24) WowK damage to ACM. Q Yes 0 NO 0 Lca -Hzed 0 Distributed (25) Proximity (P) of ACM to repaWrromzine mainm uin A. Friable

  16. 40 CFR 763.83 - Definitions.

    Science.gov (United States)

    2010-07-01

    ... means a program of work practices to maintain friable ACBM in good condition, ensure clean up of... means a method, including removal, encapsulation, enclosure, repair, operations and maintenance, that... as a boiler room or mechanical room, that is not normally frequented by students and in which...

  17. A potential phosphorite deposit on the continental margin off Chennai

    Digital Repository Service at National Institute of Oceanography (India)

    Rao, V.P; Rao, K.M.; Vora, K.H.; Almeida, F.; Subramaniam, M.M.; Souza, C.G.A.

    into four types as (1) light brown friable phosphorites (2) grey dense phosphorites (3) phosphorite sands and (4) phosphatized algal nodules/limestones. Major element composition of phosphorites indicate that the P@d2@@ O@d5@@ content is highest (31...

  18. Mayamontana coccolobae (Basidiomycota), a new sequestrate taxon from Belize

    Science.gov (United States)

    Michael A. Castellano; James M. Trappe; D. Jean Lodge

    2007-01-01

    A new semi-hypogeous, sequestrate genus and species in the Basidiomycota is described from the Maya Mountains of Belize, where it was fruiting in association with Coccoloba belizensis. Mayamontana coccolobae is characterized by small, bright orange basidiomata with a friable, loculate, red-orange to red gleba and bilaterally...

  19. [Plant biomorphology and seed germination of pioneer species of the Kamchatka volcanoes].

    Science.gov (United States)

    Voronkova, N M; Kholina, A B; Verkholat, V P

    2008-01-01

    Biomorphology, quantitative characters and seed germination of 17 pioneer plant species friable materials of volcanic eruptions (Kamchatka Peninsula) were studied. Adaptive trends in survival stress conditions are discussed. To evaluate a possibility of the cryogenic seed storage, their response to ultra low temperatures (-196 degrees C) was determine.

  20. Mevastatin-induced inhibition of cell growth in avocado suspension ...

    African Journals Online (AJOL)

    Cell suspension cultures were established using soft, friable callus derived from nucellar tissue of 'Hass' avocado (Persea americana Mill.) seed from fruit harvested 190 days after full bloom. Cell cultures were maintained in liquid medium supplemented with naphthalene acetic acid (NAA), isopentenyl adenine (iP) and ...

  1. 41 CFR 102-75.1185 - What are suitability criteria?

    Science.gov (United States)

    2010-07-01

    ..., the property will not be determined unsuitable on this basis. (2) Property containing flammable or... handling flammable or explosive material (excluding underground storage) will be determined unsuitable..., friable asbestos, PCBs, natural hazardous substances such as radon, periodic flooding, sinkholes, or earth...

  2. 24 CFR 581.6 - Suitability criteria.

    Science.gov (United States)

    2010-04-01

    ..., the property will not be determined unsuitable on this basis. (2) Property containing flammable or... handling flammable or explosive material (excluding underground storage) will be determined unsuitable..., friable asbestos, PCB's, or natural hazardous substances such as radon, periodic flooding, sinkholes or...

  3. Tracking the transformation and transport of arsenic sulfide pigments in paints: synchrotron-based X-ray micro-analyses

    NARCIS (Netherlands)

    Keune, K.; Mass, J.; Meirer, F.; Pottasch, C.; van Loon, A.; Hull, A.; Church, J.; Pouyet, E.; Cotte, M.; Mehta, A.

    2015-01-01

    Realgar and orpiment, arsenic sulfide pigments used in historic paints, degrade under the influence of light, resulting in transparent, whitish, friable and/or crumbling paints. So far, para-realgar and arsenic trioxide have been identified as the main oxidation products of arsenic sulfide pigments.

  4. Tracking the transformation and transport of arsenic sulfide pigments in paints : synchrotron-based X-ray micro-analyses

    NARCIS (Netherlands)

    Keune, Katrien; Mass, Jennifer; Meirer, Florian; Pottasch, Carol; van Loon, Annelies; Hull, Alyssa; Church, Jonathan; Pouyet, Emeline; Cotte, Marine; Mehta, Apurva

    2015-01-01

    Realgar and orpiment, arsenic sulfide pigments used in historic paints, degrade under the influence of light, resulting in transparent, whitish, friable and/or crumbling paints. So far, para-realgar and arsenic trioxide have been identified as the main oxidation products of arsenic sulfide pigments.

  5. 40 CFR Appendix E to Subpart E of... - Interim Method of the Determination of Asbestos in Bulk Insulation Samples

    Science.gov (United States)

    2010-07-01

    ... interpretation of point count data 3 is available. This method is applicable to all bulk samples of friable... matrices are not currently available. Data obtained for samples containing a single asbestos type in a... and characterization of fibrous and nonfibrous amphiboles for analytical methods development, pp. 295...

  6. Mineral resource of the month: diatomite

    Science.gov (United States)

    ,

    2013-01-01

    The article discusses the properties and applications of the mineral diatomite. According to the author, diatomite is a soft, friable and very fine-grained siliceous sedimentary rock made of the remains of fossilized diatoms. The author adds that its properties make diatomite very useful as a filtration medium and as a component in cement.

  7. Effect of ausforming on nanobainite steel

    International Nuclear Information System (INIS)

    Gong, W.; Tomota, Y.; Koo, M.S.; Adachi, Y.

    2010-01-01

    The effect of ausforming on kinetics, morphology and crystallography of nanobainite steel was examined by electron backscattered diffraction and transmission electron microscopy. Ausforming has been found to accelerate bainite transformation at 573 K. A characteristic microstructure consisting of blocky bainitic laths and retained austenite is observed in the ausformed bainite steel, where strong variant selection takes place due to the operated slip systems.

  8. Biosynthesis, Characterization, and Hemostasis Potential of Tailor-Made Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) Produced by Haloferax mediterranei

    DEFF Research Database (Denmark)

    Han, Jing; Wu, Linping; Hou, Jing

    2015-01-01

    . Consistently, two Tg were observed in the DSC curves of O-PHBV. The "blocky" feature of O-PHBV enhanced crystallinity percentages and improved Young's modulus. Notably, the film of one O-PHBV copolymer, O-PHBV-1, showed unique foveolar cluster-like surface morphology with high hydrophobicity and roughness...

  9. Julia Ninck Block Y-galeriis

    Index Scriptorium Estoniae

    2009-01-01

    Tartus Y-galeriis alates 26. oktoobrist Mooste Külalistuudio (MoKS) oktoobrikuu resident-kunstniku Julia Ninck Blocki näitus. Vene päritolu hollandi kunstnik avab oma joonistustes ja fotodes pealmise ilma ja (vee)aluse maailma suhteid

  10. Geotechnical and environmental problems related to shales in the ...

    African Journals Online (AJOL)

    EJIRO

    Six (6) samples of shale and five (5) water samples from hand-dug wells and boreholes, from different locations within the ... dark grey in colour, blocky, and non-micaceous in most locations. ..... Advances in water treatment and environmental ...

  11. Characterization And Classification Of The Inland Valley Soils Of ...

    African Journals Online (AJOL)

    Six profiles located in the inland valley soils of central Cross River State were studied. The surface horizon colour of the first four were either dark Grey or dark brown. The last two profiles were grey. All subsurface horizons were either greyish or brownish and highly mottled. The structure of all the profiles were either blocky ...

  12. of contrasting features in ohaji, south-eastern nigeria

    African Journals Online (AJOL)

    it could be argued that some of the changes resulted from direct and indirect effects. ... classification of the USDA were correlated to the ... blocky structure in the 23-year-old vegetation and weak, fine ... vigorous growth of plant roots and soil organisms. The variation in ..... Spatial dependence of some physical properties of a.

  13. Establecimiento de un cultivo de celulas en suspensión de Eucalyptus cinérea Establishment of cell suspension culture of Eucalyptus cinerea

    Directory of Open Access Journals (Sweden)

    Arias Zabala Mario

    2002-06-01

    Full Text Available Se desarrolla un protocolo para la obtención y establecimiento de suspensiones celulares de E. cinerea. La concentración de las hormonas 2,4 D Y BAP tienen un efecto significativo en la formación de callos friables de E. cinerea, obteniendo una respuesta periódica en la formación de callos friables con respecto a la concentración de las hormonas. Puede obtenerse hasta un 90% de formación de callos friables con varias combinaciones hormonales; primero, con concentraciones alrededor de 3,0 mg/L de 2,4 D Y 1,0 mg/L de BAp, y segundo, alrededor de 6,0 mg/L de 2,4 D Y1,0 mg/L de BAP. A partir de los callos anteriores, se obtienen suspensiones celulares con un activo crecimiento celular, con tiempos de duplicación entre cuatro y siete días, y alcanzando densidades celulares de 15 g células secas/L. Las suspensiones de E. cinerea ofrecen una herramienta importante para la propagación de esta especie vía embriogénesis somática, estudio de biorreactores, producción de metabolitos secundarios y procesos de biotransformación.A protocol is developed for obtaining and establishment of E. cinerea cell suspension. The concentration of hormones 2,4 D and BAP have a significant effect in the formation of friable callus of E. cinerea, obtaining a periodic answer in the formation of friable callus with regard to hormones concentration. It can be obtained until 90% of formation of friable callus in several hormone combinations, first with concentrations around 3,0 mg/L of 2,4 D and 1,0 mg/L of BAP; and second, around 6,0 mgIL of 2,4 D and 1,0 mg/L of BAP. Using the last callus, cell suspensions are obtained with an active cellular growth, with times of duplication between 4 and 7 days and obtaining cell densities of 15 g of dry cells/L. The suspensions of E. cinerea offer an important tool for the propagation of this specie by somatic embryogenesis, bioreactors study, production of secondary metabolites and biotransformation processes.

  14. Mineralogy and petrography of HAL, an isotopically-unusual Allende inclusion

    Science.gov (United States)

    Allen, J. M.; Grossman, L.; Lee, T.; Wasserburg, G. J.

    1980-01-01

    Results of a detailed mineralogical and textural study of the HAL (Hibonite ALlende) inclusion of the Allende meteorite, which has been found to exhibit no Mg-26 excesses despite very high Al-27/Mg-24 ratios and large fractionation effects with small nuclear effects in its Ca, are reported. The inclusion is found to consist of three up to 1-mm diameter hibonite crystals partially surrounded by a black rim resembling a devitrified glass and containing an anisotropic Al-Fe oxide, which is in turn surrounded by a 2-mm thick friable rim sequence consisting of five layers distinguishable by mineral composition. From the available evidence, it is concluded that each of the layers of the friable rim formed by the accretion of an assemblage of condensate grains rather than by the complete reaction of a HAL precursor with a nebular gas, thus explaining its unusual isotopic characteristics and supporting the conclusion that the solar nebular contained isotopically-distinct reservoirs.

  15. Nasal and oral masses in a dog.

    Science.gov (United States)

    Levy, Esther; Mylonakis, Mathios E; Saridomichelakis, Manolis N; Polizopoulou, Zoe S; Psychogios, Vassilios; Koutinas, Alexander F

    2006-03-01

    A 5-year-old, intact male, stray dog was presented in poor body condition, with pallor, muzzle deformity, multiple oozing fistulas with grass awns, bilateral sanguinopurulent nasal discharge and a fleshy friable mass occupying part of the hard palate. A friable mass occupying both nasal cavities was found on rhinoscopy. The dog had moderate nonregenerative normochromic-microcytic anemia, thrombocytopenia, hyperglobulinemia, and hypoalbuminemia. Cytologic preparations of the nasal and oral masses contained a neoplastic population of round cells with intracytoplasmic and extracellular vacuoles. Leishmania amastigotes also were observed, in the cytoplasm of macrophages and, occasionally, within neoplastic cells. A diagnosis of transmissible venereal tumor and concurrent leishmaniosis was made. Treatment with vincristine and allopurinol resulted in complete resolution of clinical signs and disappearance of the masses. The presence of amastigotes in neoplastic TVT cells may suggest an alternative mode of transmission of canine leishmaniosis where these diseases co-exist.

  16. Elevated-temperature mechanical stability and transformation behavior of retained austenite in a quenching and partitioning steel

    Energy Technology Data Exchange (ETDEWEB)

    Min, Junying, E-mail: junying.min@gmail.com [Chair of Production Systems, Ruhr-University Bochum, Bochum 44780 (Germany); Hector, Louis G. [General Motors Research & Development, Warren, MI 48095-9055 (United States); Zhang, Ling; Lin, Jianping [School of Mechanical Engineering, Tongji University, Shanghai 201804 (China); Carsley, John E. [General Motors Research & Development, Warren, MI 48095-9055 (United States); Sun, Li [General Motors China Science Lab, Shanghai 201206 (China)

    2016-09-15

    The mechanical stability and transformation behavior of both film and blocky retained austenite (RA) in a quenching and partitioning steel are investigated at 293 K, 423 K and 573 K with X-ray diffraction measurements and transmission electron microscopy. Blocky RA both completely and incompletely transforms to twinned martensite during deformation at 293 K and 423 K, respectively, and completely transforms to lath martensite during deformation at 573 K. At 293 K and 423 K, only the film RA with widths larger than ~70 nm transforms to twinned martensite. However, film RA incompletely transforms to lath martensite at 573 K. Hence, RA transformation is non-monotonic with temperature. Significant carbide formation at 573 K, and therefore less carbon to stabilize RA, overcomes the increase in austenite stability due to the decrease in the temperature-dependent chemical driving force for the martensite transformation.

  17. Morphology change of retained austenite during austempering of carbide-free bainitic steel

    Energy Technology Data Exchange (ETDEWEB)

    Hofer, Christina, E-mail: christina.hofer@unileoben.ac.at [Department of Physical Metallurgy and Materials Testing, Montanuniversität Leoben, Franz-Josef-Straße 18, 8700 Leoben (Austria); Winkelhofer, Florian [Research and Development - Business Unit Coil, voestalpine Stahl GmbH, voestalpine‐Straße 3, A-4020 Linz (Austria); Clemens, Helmut; Primig, Sophie [Department of Physical Metallurgy and Materials Testing, Montanuniversität Leoben, Franz-Josef-Straße 18, 8700 Leoben (Austria)

    2016-05-10

    A change in the mechanical properties of a carbide-free bainitic steel was observed during prolonged holding at austempering temperature after termination of the bainitic transformation. To determine the origin of the property change, the microstructure was investigated by correlative electron microscopy. Although the retained austenite content remains the same during prolonged holding, its morphology changes from thin films separating the individual bainitic sub-units to a more globular structure. Since films of austenite contain a higher C concentration, the blocky austenite becomes gradually enriched in C during this morphology change. The more homogeneous distribution of the C after prolonged austempering leads to higher deformability as a result of a more pronounced TRIP effect. - Highlights: • Higher deformability after prolonged austempering of carbide-free bainite. • Microstructure-property relationship revealed by correlative electron microscopy. • Change in austenite morphology. • Spherodization of film austenite; C enrichment & homogenization of blocky austenite.

  18. In vitro neoplastic transformation of plant callus tissue by γ-radiation

    International Nuclear Information System (INIS)

    Pandey, K.N.; Sabharwal, P.S.

    1979-01-01

    Tumours have been induced by γ-radiation in callus tissue derived from a monocotyledonous flowering plant, Haworthia mirabilis Haw. The transformed tissue exhibited compact texture, excessive cell proliferation and loss of capacity for organogenesis. Tumors were characterized by their ability to undergo continuous autonomous growth on minimal media in the subsequent 4 generations of subculture. In contrast, the nonirradiated control tissue grew with friable texture, required inositol or growth hormones and showed prolific differentiation of vegetative buds. (Auth.)

  19. Elimination of the dirty crust of white alterated glaze from excavated ceramics using the laser cleaning alternative

    OpenAIRE

    Aura Castro, Elvira; Saiz Mauleón, María Begoña; Domenech Carbo, Mª Teresa

    2006-01-01

    The laser technique has been applied to the cleaning process of glazed decorated ceramics from excavation sites. The use of this method arises as the only possible alternative in the process of cleaning pieces with crusts of dirt that are extremely hard and strongly stuck over altered and friable white glaze layers. The study carried out has allowed to fix the optimal laser parameters in the elimination of the dark dirty layer found on several fragments from different periods. The study has b...

  20. Scanning electron microscopy of superficial white onychomycosis*

    Science.gov (United States)

    de Almeida Jr., Hiram Larangeira; Boabaid, Roberta Oliveira; Timm, Vitor; Silva, Ricardo Marques e; de Castro, Luis Antonio Suita

    2015-01-01

    Superficial white onychomycosis is characterized by opaque, friable, whitish superficial spots on the nail plate. We examined an affected halux nail of a 20-year-old male patient with scanning electron microscopy. The mycological examination isolated Trichophyton mentagrophytes. Abundant hyphae with the formation of arthrospores were found on the nail's surface, forming small fungal colonies. These findings showed the great capacity for dissemination of this form of onychomycosis. PMID:26560225

  1. Unusual presentation of keratocystic odontogenic tumor: Two case reports

    Directory of Open Access Journals (Sweden)

    Sunitha Kesidi

    2016-01-01

    Full Text Available Keratocystic odontogenic tumor (KOT is a common odontogenic cyst with aggressive behavior with a high recurrence rate. Features that predict recurrence of KOT are thin friable epithelium which is difficult to enucleate and presence of satellite cysts in the fibrous wall. Most of the lesions grow in an anteroposterior direction without causing any bony expansion. Here, we report two cases of KOT with different clinical presentation.

  2. Primary oral and nasal transmissible venereal tumor in a mix-breed dog

    OpenAIRE

    Rezaei, Mahdieh; Azizi, Shahrzad; Shahheidaripour, Shima; Rostami, Sara

    2016-01-01

    Transmissible venereal tumor (TVT) is a coitally transmitted tumor of dogs with widespread distribution. The present study describes the occurrence of the primary oral and nasal TVT in a 10-year-old, female, mix-breed dog. The case was presented with a history of anorexia, inability to swallow and dyspnea. Clinical examinations revealed the emaciation, muzzle deformity due to the presence of a friable, fleshy, cauliflower-like mass in the oral cavity and submandibular lymphadenopathy. TVT was...

  3. Component, Context, and Manufacturing Model Library (C2M2L)

    Science.gov (United States)

    2012-11-01

    nickel chloride, sulfate chloride, all sulfate, hard nickel, black nickel, and electroless nickel (used for metal and plastic, requires no electrical... rice husk etc. Table 20includes a list of common abrasive materials and their powders. 65 Approved for public release; distribution...friable abras ive media which i s reusable but less durable that Brown Aluminum Oxide. Uses: For cleaning, peening, and cosmetic finishing

  4. Polyimide-Foam/Aerogel Composites for Thermal Insulation

    Science.gov (United States)

    Williams, Martha; Fesmire, James; Sass, Jared; Smith, Trent; Weoser. Erol

    2009-01-01

    Composites of specific types of polymer foams and aerogel particles or blankets have been proposed to obtain thermal insulation performance superior to those of the neat polyimide foams. These composites have potential to also provide enhanced properties for vibration dampening or acoustic attenuation. The specific type of polymer foam is denoted "TEEK-H", signifying a series, denoted H, within a family of polyimide foams that were developed at NASA s Langley Research Center and are collectively denoted TEEK (an acronym of the inventors names). The specific types of aerogels include Nanogel aerogel particles from Cabot Corporation in Billerica, MA. and of Spaceloft aerogel blanket from Aspen Aerogels in Northborough, MA. The composites are inherently flame-retardant and exceptionally thermally stable. There are numerous potential uses for these composites, at temperatures from cryogenic to high temperatures, in diverse applications that include aerospace vehicles, aircraft, ocean vessels, buildings, and industrial process equipment. Some low-temperature applications, for example, include cryogenic storage and transfer or the transport of foods, medicines, and chemicals. Because of thermal cycling, aging, and weathering most polymer foams do not perform well at cryogenic temperatures and will undergo further cracking over time. The TEEK polyimides are among the few exceptions to this pattern, and the proposed composites are intended to have all the desirable properties of TEEK-H foams, plus improved thermal performance along with enhanced vibration or acoustic-attenuation performance. A composite panel as proposed would be fabricated by adding an appropriate amount of TEEK friable balloons into a mold to form a bottom layer. A piece of flexible aerogel blanket material, cut to the desired size and shape, would then be placed on the bottom TEEK layer and sandwiched between another top layer of polyimide friable balloons so that the aerogel blanket would become

  5. Importance of Soil Quality in Environment Protection

    OpenAIRE

    Márta Birkás; Tibor Kalmár; László Bottlik; Tamás Takács

    2007-01-01

    Soil quality can be characterised by the harmony between it’s physical and biological state and the fertility. From the practical crop production viewpoint, some important contrasting factors of soil quality are: (1) soil looseness – compaction; (2) aggregation – clod and dust formation; friable structure – smeared or cracked structure; (3) organic material: conservation – decrease; (4) soil moisture: conservation – loss; water transmission – water-logging; (5) at least soil condition as a re...

  6. Extrusion of hydrogel exoplant into upper eyelid 16 years after a scleral buckle procedure

    Directory of Open Access Journals (Sweden)

    Chirag P Shah

    2011-01-01

    Full Text Available Sixteen years after scleral buckle surgery with a hydrogel episcleral exoplant, a 43-year-old woman presented with progressive binocular diplopia, ptosis, and an expanding mass in her upper eyelid. She underwent surgical removal of the hydrogel exoplant through an anterior approach. The exoplant proved to be friable, fragmented, and encapsulated in a fibrous tissue; the exoplant was removed in its entirety. Postoperatively, the eyelid mass resolved, while her diplopia and ptosis improved slightly.

  7. Fractional-Order Total Variation Image Restoration Based on Primal-Dual Algorithm

    OpenAIRE

    Chen, Dali; Chen, YangQuan; Xue, Dingyu

    2013-01-01

    This paper proposes a fractional-order total variation image denoising algorithm based on the primal-dual method, which provides a much more elegant and effective way of treating problems of the algorithm implementation, ill-posed inverse, convergence rate, and blocky effect. The fractional-order total variation model is introduced by generalizing the first-order model, and the corresponding saddle-point and dual formulation are constructed in theory. In order to guarantee $O(1/{N}^{2})$ conv...

  8. The avant-garde is not dead / René Block ; intervjueerinud Eero Epner

    Index Scriptorium Estoniae

    Block, René, 1942-

    2010-01-01

    Intervjuu saksa galeristi ja kuraatori René Blockiga, kes 1964. a. avas Berliinis galerii, kus eksponeeris J. Beuysi, S. Polke, G. Richteri jt. töid. Töötamisest kuraatorina alates 1970. aastatest, biennaalide tulevikust, avangardist. René Blocki galeriis 1966. a. toimunud Joseph Beuys'i performance'ist "Kuidas seletada kunsti surnud jänesele", millest inspireerituna teater NO99 lõi samanimelise lavastuse

  9. Conversion of Low Quality Waste Heat to Electric Power with Small-Scale Organic Rankine Cycle (ORC) Engine/Generator Technology

    Science.gov (United States)

    2016-06-01

    block (expander) that allows gas expansion and converts the energy into rotational work, • an electric induction generator driven from the power block...is in the form of waste heat – thermal energy emitted via hot exhaust and heat removal systems associated with engine and other electric generator ...than 250 ºC), improves energy efficiency by reducing energy consumption associated with electrical generation and reduces greenhouse gas emissions

  10. Asbestos removal and disposal information system: a user's guide

    International Nuclear Information System (INIS)

    Knight, P.S.; Eisenhower, B.M.

    1982-10-01

    Program ASBS01, written for the staff of the Department of Environmental Management (DEM) at Oak Ridge National Laboratory (ORNL), is an on-line management information system that provides file maintenance and information retrievability for demolition and/or renovation operations involving friable (capable of becoming an airborne health hazard) asbestos material at the Laboratory. System 1022 is the data base management system used. The screen processor SCOPE provides the DEM staff with system prompts for ease of use and data integrity. Data for the system comes from two UCN forms: (1) Notice of Intention to Demolish or Renovate Friable Asbestos Material (UCN-13385) and (2) Request for the Disposal of Asbestos or Material Containing Asbestos (UCN-13386). Examples of the forms are in Appendix A. Data is entered into the system as requests are submitted to DEM. Total amounts of friable asbestos removed in demolition and/or renovation operations can be generated by the program upon user request. These totals are submitted in a quarterly report to the Environmental Protection Branch of the US Department of Energy (DOE) on a continuing basis (see Appendix B). This report describes the operation of the computer program ASBS01 from data entry to generation of totals. Each data attribute of the master file ASBSTO.DMS is described in detail, and a sample session is given for user reference

  11. Enhanced proline synthesis may determine resistance to salt stress in tomato cultivars

    International Nuclear Information System (INIS)

    Ali, S.; Khan, N.U.

    2011-01-01

    The physiological and biochemical responses of tomato cultivars were studied at Khyber Pakhtunkhwa Agricultural University, Peshawar, Pakistan during 2005-2006 for salt tolerance. Tomato cultivars were Roma Rio Super, Roma V.F., Chinese 87-5, Rio Grand and Super Blocky and subjected to salt stress (75 mM NaCl). Fresh weight, dry weight, and ions sodium and potassium accumulation, Na/sup +/K sup +/ ratio and proline content were determined after imposing the tomato cultivars to NaCl salt for 80 days. Salt stress significantly decreased the fresh and dry weight in Roma Rio Super, Roma V.F, Chinese 87-5 and Rio Grand, however, in Super Blocky the fresh and dry weight were enhanced under stress conditions. Salinity stress increased sodium uptake from 191.828 to 436.170 mu mg/sup -1/ D wt while potassium accumulation decreased from 1033.12 to 926.80 mu mg/sup -1/ D wt resulting in higher Na/sup +/ ratio in stressed (0.48 g) as compared to unstressed control (0.19). The mean proline contents also increased from 28.95 to 40.96 mu M Proline g/sup -1/ F. wt with the maximum increase (57.378%) in Super Blocky followed by Rio Grand (49.325%). (author)

  12. Effect of retained austenite stability and morphology on the hydrogen embrittlement susceptibility in quenching and partitioning treated steels

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Xu [State Key Lab of Metal Matrix Composites, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai Jiao Tong University, Shanghai 200240 (China); Zhang, Ke [School of Materials Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093 (China); Li, Wei, E-mail: weilee@sjtu.edu.cn [State Key Lab of Metal Matrix Composites, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Jin, Xuejun, E-mail: jin@sjtu.edu.cn [Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai Jiao Tong University, Shanghai 200240 (China)

    2016-03-21

    The effect of retained austenite (RA) stability and morphology on the hydrogen embrittlement (HE) susceptibility were investigated in a high strength steel subjected to three different heat treatments, i.e., the intercritical annealing quenching and partitioning (IAQP), quenching and partitioning (QP) and quenching and tempering (QT). IAQP treatment results in the coexistence of blocky and filmy morphologies and both QP and QT treatments lead to only filmy RA. No martensitic transformation occurs in QT steel during deformation, while the QP and IAQP undergo the transformation with the same extent. It is shown that the HE susceptibility increases in the following order: QT, QP and IAQP. Despite of the highest strength level and the highest hydrogen diffusion rate, the QT steel is relative immune to HE, suggesting that the metastable RA which transforms to martensite during deformation is detrimental to the HE resistance. The improved resistance to HE by QP treatment compared with IAQP steel is mainly attributed to the morphology effect of RA. Massive hydrogen-induced cracking (HIC) cracks are found to initiate in the blocky RA of IAQP steel, while only isolate voids are observed in QP steel. It is thus deduced that filmy RA is less susceptible to HE than the blocky RA.

  13. Surprising discovery of high-grade pelitic schist on Cavalli Seamount, offshore Northland

    International Nuclear Information System (INIS)

    Mortimer, N.; Walker, N.H.; Herzer, R.H.; Calvert, A.; Seward, D.

    1999-01-01

    Serendipity waits in the world's unexplored places. In March 1999, GNS's ONSIDE expedition to the South Fiji Basin made two dredge hauls on Cavalli seamount expecting to recover Miocene oceanic volcanic rocks. Instead dredge DIA recored 1 kg of 10 cm slickensided and chloritised schist pieces and dredge DIB, which was 1.1 km distant, 100 kg of well-foliated biotite schist, mainly in the form of two large subangular boulders. The presence of calsilicate bands initially suggested a correlation with Buller or Takaka Terranes, but whole rock chemical composition of the schist is more consistent with Murihiku, Waipapa or Pahau Terranes. U-Pb TIMS gheochronometry of individual detrital zircons indicates a maximum 170Ma depositional age for the schist protolith, thus clearly ruling out a Buller or Takaka correlation. Rb-Sr whole rock data suggest a young (Cenozoic?) metamorphic age. (author)

  14. Micromorphological characteristics of sandy forest soils recently impacted by wildfires in Russia

    Science.gov (United States)

    Maksimova, Ekaterina; Abakumov, Evgeny

    2017-04-01

    Two fire-affected soils were studied using micromorphological methods. The objective of the paper is to assess and compare fire effects on the micropedological organisation of soils in a forest-steppe zone of central Russia (Volga Basin, Togliatti city). Samples were collected in the green zone of Togliatti city. The results showed that both soils were rich in quartz and feldspar. Mica was highly present in soils affected by surface fires, while calcium carbonates were identified in the soils affected by crown fires. The type of plasma is humus-clay, but the soil assemblage is plasma-silt with a prevalence of silt. Angular and subangular grains are the most dominant soil particulates. No evidence of intensive weathering was detected. There was a decrease in the porosity of soils affected by fires as a consequence of soil pores filled with ash and charcoal.

  15. Petrology of dune sand derived from basalt on the Ka'u Desert, Hawaii

    Science.gov (United States)

    Gooding, J. L.

    1982-01-01

    Dune sand from the Ka'u Desert, southwest flank of Kilauea volcano, Hawaii, is moderately well-sorted (median = 1.60 Phi, deviation = 0.60, skewness = 0.25, kurtosis = 0.68) and composed mostly of frosted subangular particles of basalt glass ('unfractionated' olivine-normative tholeitte), olivine, lithic fragments (subophitic and intersertal basalts; magnetite-ilmenite-rich basalts), reticular basalt glass, magnetite, ilmenite, and plagioclase, in approximately that order of abundance. Quantitative lithological comparison of the dune sand with sand-sized ash from the Keanakakoi Formation supports suggestions that the dune sand was derived largely from Keanakakoi ash. The dune sand is too well sorted to have been emplaced in its present form by base-surge but could have evolved by post-eruption reworking of the ash.

  16. Premilinary studies for optimiziing a protocol for obtaining embryogenic calluses in two rubber (Hevea brasiliensis Mull. Arg clones from different geographical origins

    Directory of Open Access Journals (Sweden)

    Santiago Cadavid Ruiz

    2006-01-01

    Full Text Available The influence of growth regulators on obtaining friable rubber (Hevea brasiliensis Müll. Arg. calluses with no plant regeneration as investigated. Two clones having different geographical origin were used in all trails carried out in this study: FX 3864 (South-American and PB 254 (Asian. Young leaves and eight- to ten-week-old seed integument from both clones were used as explants in several experiments; they were initially cultured in MH medium (Carron, et ál., 1989, modified MH medium (Montoro, et ál., 1993, 2000 and modified MS medium (Carron, et at,. 1992, no positive response being obtained by days 25 or 50. However, other trials were carried out with the integument in modified MS medium (1962, 0.67 mg/L BAP and 0.66 mg/L 2-4 D being added as medium for initiating embryogenesis, the formation of white, friable calluses being observed by day 25 in the two selected clones. These calluses were sub-cultured in MS supplemented with 0.35 mg/L BAP and 0.2 mg/L 2-4 D as callogenesis expression medium, embryogenic expression being observed in both clones by day 50. Equally friable white calluses were obtained from young leaves in the two clones in MS medium supplemented with 1.0 mg/L BAP, 1.0 mg/L ANA but without IBA and kinetin by day 25. Calluses sub-cultured in the same medium supplemented with 0.5 mg/L BAP and 0.5 mg/L ANA began to show increased friability after 50 days. culture. This work is a partial report of a macro-project for optimising a protocol for rubber (Hevea brasiliensis  multiplication by somatic embryogenesis.

  17. Embrittlement of Intercritically Reheated Coarse Grain Heat-Affected Zone of ASTM4130 Steel

    Science.gov (United States)

    Li, Liying; Han, Tao; Han, Bin

    2018-04-01

    In this investigation, a thermal welding simulation technique was used to investigate the microstructures and mechanical properties of the intercritically reheated coarse grain heat-affected zone (IR CGHAZ) of ASTM4130 steel. The effect of post weld heat treatment (PWHT) on the toughness of IR CGHAZ was also analyzed. The toughness of IR CGHAZ was measured by means of Charpy impact, and it is found that IR CGHAZ has the lowest toughness which is much lower than that of the base metal regardless of whether PWHT is applied or not. The as-welded IR CGHAZ is mainly composed of ferrite, martensite, and many blocky M-A constituents distributing along grain boundaries and subgrain boundaries in a near-connected network. Also, the prior austenite grains are still as coarse as those in the coarse grain heat-affected zone (CGHAZ). The presence of the blocky M-A constituents and the coarsened austenite grains result in the toughness deterioration of the as-welded IR CGHAZ. Most of the blocky M-A constituents are decomposed to granular bainite due to the effect of the PWHT. However, PWHT cannot refine the prior austenite grains. Thus, the low toughness of IR CGHAZ after PWHT can be attributed to two factors, i.e., the coarsened austenite grains, and the presence of the remaining M-A constituents and granular bainite, which are located at grain boundaries and subgrain boundaries in a near-connected network. The absorbed energy of the IR CGHAZ was increased by about 3.75 times, which means that the PWHT can effectively improve the toughness but it cannot be recovered to the level of base metal.

  18. Microstructure and partitioning behavior characteristics in low carbon steels treated by hot-rolling direct quenching and dynamical partitioning processes

    International Nuclear Information System (INIS)

    Li, Yun-jie; Li, Xiao-lei; Yuan, Guo; Kang, Jian; Chen, Dong; Wang, Guo-dong

    2016-01-01

    In this work, a new process and composition design are proposed for “quenching and partitioning” or Q&P treatment. Three low carbon steels were treated by hot-rolling direct quenching and dynamical partitioning processes (DQ&P). The effects of proeutectoid ferrite and carbon concentration on microstructure evolution and mechanical properties were investigated. The present work obtained DQ&P prototype steels with good mechanical properties and established a new notion on compositions for Q&P processing. Microstructures were characterized by means of electro probe microanalyzer (EPMA), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM) and X-ray diffraction (XRD), especially the morphology and size of retained austenite. Mechanical properties were measured by uniaxial tensile tests. The results indicated that introducing proeutectoid ferrite can increase the volume fraction of retained austenite and thus improve mechanical properties. TEM observation showed that retained austenite included the film-like inter-lath austenite and blocky austenite located in martensite/ferrite interfaces or surrounded by ferrites. It was interesting that when the carbon concentration is as low as ~ 0.078%, the film-like inter-lath untransformed austenite cannot be stabilized to room temperature and almost all of them transformed into twin martensite. The blocky retained austenite strengthened the interfaces and transformed into twin martensite during the tensile deformation process. The PSEs of specimens all exceeded 20 GPa.%. - Highlights: •This study focused on a new process: Q&P process applying dynamical partitioning. •Ferrite can increase the volume fraction of retained austenite. •The film-like austenite and the blocky austenite were observed. •The low carbon steels treated by new process reached PSEs higher than 20 GPa.%.

  19. Oropharyngeal rhinosporidiosis in a migrant worker--a delayed presentation.

    Science.gov (United States)

    Shailendra, S; Prepageran, N

    2008-03-01

    Rhinosporidiosis is a chronic granulomatous disease caused by an aquatic protistan parasite in the class of Mesomycetozoea, that is endemic in India and the subcontinent. This is a case report of a rhinosporidiosis presenting in an individual from Myanmar, whom had been working in Malaysia for the past four years. The disease is characterized by the appearance of polypoidal, friable growths that contain numerous spore filled cysts that stain with PAS staining. This disease is rarely seen in Malaysians due to the extensive urbanization in Kuala Lumpur, however the increasing numbers of migrant workers in Malaysia today necessitates an increasing awareness in clinicians of the possibility of these conditions.

  20. Somatic embryogenesis and plant regeneration in tissue cultures of sweet potato (Ipomea batatas Poir.).

    Science.gov (United States)

    Liu, J R; Cantliffe, D J

    1984-06-01

    Leaf, shoot-tip, stem, and root explants of sweet potato (Ipomea batatas Poir.) gave rise to two kinds of callus on nutrient agar medium containing 0.5 to 2.0 mg/l 2,4-D. One callus, bright- to pale-yellow, was compact and organized, while the other was dull-yellow and friable. The former callus gave rise to numerous globular and heart-shaped embryoids. When transferred onto hormone-free medium, the embryoids readily developed into a torpedo-shape before germination. The plantlets were transplanted to soil where they flowered and formed storage roots at maturity.

  1. Investigation of Diatomite Properties from Ankara-Kızılcahamam and Çankırı-Çerkeş Regions

    OpenAIRE

    ARUNTAŞ, H. Yılmaz

    1998-01-01

    The physical properties, chemical and mineralogical compositions and microscopic structures of diatomites collected from Ankara-Kızılcahamam and Çankırı-Çerkeş regions were examined in this study. The diatomites were found to be pure, amorphous, usually soft and easily friable with particle size of 5-50 mm. It was determined that the diatomites were highly with a high water absorption capacity and contained plagioclase, smectite, and quartz minerals. The specific gravity was less th...

  2. Producción de metabolitos secundarios en cultivo de raíces in vitro y suspensiones celulares de Ipomoea carnea spp. carnea Jacq.

    OpenAIRE

    Rojas Idrogo, Consuelo; Kato, Massuo J.; Delgado-Paredes, Guillermo E.; Segal Floh, Eny Iochevet; Handro, Walter

    2014-01-01

    Ipomoea carnea spp. carnea Jacq. es un arbusto dominante en el bosque estacionalmente seco del Perú y Ecuador. Los cultivos de raíces fueron establecidos en medio MS con diferentes concentraciones de AIB, sacarosa y combinaciones de AIB-sacarosa. Diversos explantes obtenidos de plántulas in vitro y plantas silvestres se cultivaron en diferentes combinaciones de 2,4-D, AIA, ANA y BAP, para inducir callos friables, dependiendo del tipo de explante y los reguladores de creci...

  3. An Incidental Finding of AL-associated Amyloidosis Presenting as Gastric Ulcers

    Directory of Open Access Journals (Sweden)

    Nadia Huq

    2018-01-01

    Full Text Available Gastrointestinal tract amyloidosis has been reported in rare instances and related symptoms are usually nonspecific to the disease process. We present a patient who initially had melena on anticoagulation and endoscopy revealed a bleeding gastric ulcer. Hemostasis was achieved. The patient had a recurrence of symptoms despite being off anticoagulation months later and at that time repeat endoscopy showed multiple gastric ulcers with surrounding friable mucosa. Biopsy results were significant for light chain associated-amyloidosis. This case represents a rare cause of gastric ulcer.

  4. Recurrent infective endocarditis causing heart valve failure: A case report

    Directory of Open Access Journals (Sweden)

    Victoria McIntyre, BASc Chemical Engineering (2018 candidate

    2017-11-01

    Full Text Available Infective endocarditis (IE is an infection that does not usually respond rapidly to treatment, often because its early symptoms are non-specific. The diseased valves (native or bioprosthetic may be calcified and the thrombotic vegetations on them typically friable and embolize easily. Left untreated IE leads to damage to the infected valve and to congestive heart failure (CHF. Its treatment usually requires heart valve replacement. Our 69-year-old patient had IE, and underwent aortic valve replacement (AVR with a bioprosthesis. This case stresses the complications of IE and its tendency to recur in patients with bioprosthetic heart valves (BHV who previously had IE.

  5. A roe deer from the Pliocene of Hidalgo, central Mexico

    Directory of Open Access Journals (Sweden)

    Eduardo Jiménez-Hidalgo

    2015-12-01

    Full Text Available Mexican Pliocene cervids are very poorly known. We report on new fossil material of the roe deer Capreolus constantini recovered from the Pliocene Atotonilco El Grande Formation of Santa María Amajac, Hidalgo (central Mexico. The specimens were collected from a series of layers of friable to moderately indurated polymictic conglomerate supported by a sandstone-tuffaceous-calcareous matrix. This species was formerly known only from the late Pliocene of Udunga, Russia, thus implying a dispersal event to North America around 4.0 Ma. This cervid is one of the very small number of mammals recorded from the poorly sampled Pliocene temperate deposits of Mexico.

  6. Acute Gastrointestinal Bleeding in Olmesartan-Associated Collagenous Gastroduodenitis: A Potential Endoscopic Complication

    Directory of Open Access Journals (Sweden)

    Rachel Hudacko

    2018-01-01

    Full Text Available Collagenous gastroenteritis is a rare disease that is known to be associated with the drug olmesartan, an angiotensin II receptor antagonist used to treat hypertension. It is characterized histologically by increased subepithelial collagen deposition with associated inflammation and epithelial injury. Endoscopically, the mucosa appears inflamed and friable and may be nodular or atrophic. We report a case of acute gastric bleeding on direct mucosal contact during endoscopy in a patient with olmesartan-associated collagenous gastroduodenitis to raise awareness of this potential endoscopic complication.

  7. Desquamative gingivitis: what's behind it? A case report.

    Science.gov (United States)

    Parwani, Simran R; Parwani, Rajkumar N

    2014-01-01

    Desquamative gingivitis (DG) is a clinical term used to describe red, painful, glazed, friable gingiva. It may be a manifestation of a mucocutaneous condition, such as lichen planus or other vesiculobulous disorders. Dentists must be aware of this rare clinical entity in order to distinguish DG from the far more common plaque-induced gingivitis. This case is unique in that it involves oral lichen planus and chronic DG, which may be secondary to plaque or a manifestation of the oral lichen planus. Intraoral examination and biopsy reports revealed features of chronic DG and oral reticular lichen planus.

  8. Lymphoma of the Cervix

    Directory of Open Access Journals (Sweden)

    Juanita Parnis

    2012-01-01

    Full Text Available Primary non-Hodgkins lymphoma of the uterine cervix is a very rare diagnosis. A 54-year-old woman presented with a 3-month history of postmenopausal bleeding per vaginum. On examination, a friable, fungating lesion was seen on the cervix. Histology revealed a CD 20 positive high-grade non-Hodgkin’s diffuse large B cell lymphoma from cervical biopsies and endometrial curettage. She was diagnosed as stage IE after workup and subsequently treated with six cycles of R-CHOP chemotherapy followed by radiotherapy of the involved field.

  9. The Tacuarembo formation (late jurassic-early cretaceiys): ataphonomical approach

    International Nuclear Information System (INIS)

    Perea, D.

    2007-01-01

    The Tacuarembo Formation of Uruguay exhibits the only body fossils from Botucatu desert, at Parana basin. The taphonomic pattern of this unit was studied in all fossiliferous localities and 4 modes were distinguished: 1)bonebeds, 2) Friable sandstone levels with fragments and clay pellets, 3) articulated and not fragmented remains, 4) molds. These modes clearly reflect a subaqueous system showing different degrees in deepness, energy and distance to the shore border. The two first referred modes which are associated to coarser grain sizes including dinosaur remains, represent high energy flows nearer to the terrestrial margins of the system

  10. From vein precipitates to deformation and fluid rock interaction within a SSZ: Insights from the Izu-Bonin-Mariana fore arc

    Science.gov (United States)

    Micheuz, Peter; Quandt, Dennis; Kurz, Walter

    2017-04-01

    characterized by blocky carbonates and idiomorphic to blocky zeolites. Blocky carbonates locally exhibit zonation patterns. Type III and type IV veins are both assumed to be extensional veins. Type III is characterized by syntaxial growth and elongate blocky carbonate minerals. They predominantly occur as asymmetric syntaxial veins, locally exhibiting more than one crack-seal event. Type IV veins are defined as antitaxial fibrous carbonates. Type II veins commonly show deformation microstructures like twinning (type I/II twins), slightly curved twins, and subgrain boundaries indicative of incipient plastic deformation. Based on these observations differential stresses around 50 MPa were needed to deform vein minerals, presumably related to IBM fore arc extension due to the retreat of the subducted Pacific plate. We acknowledge financial support by the Austrian Research Fund (P27982-N29) to W. Kurz

  11. Evidences for incipient hydrothermal event(s) in the Central Indian Basin: A review

    Digital Repository Service at National Institute of Oceanography (India)

    Iyer, S.D.

    that on igniting thermite (Al+Fe 3 O 4 ) melt, a basalt analog in volcanic models, with quartzo-feldspathic materials and water in steel containers irregular aggregates, spheriods and blocky particles of 1 µm to 2 mm with basaltic melt composition are formed... Centers. New York: Plenum Press, 491–502. Bonatti, E., and Honnorez, J., 1976. Sections of the earth’s crust in the equatorial Atlantic. J. Geophys. Res., 81: 4104–4116. Boulegue, J., and Mariotti, A., 1990. Carbonate cements and fluid circulation...

  12. Using an Augmented Lagrangian Method and block fracturing in the DDA method

    International Nuclear Information System (INIS)

    Lin, C.T.; Amadei, B.; Sture, S.

    1994-01-01

    This paper presents two extensions to the Discontinuous Deformation Analysis (DDA) method orginally proposed by Shi for modeling the response of blocky rock masses to mechanical loading. The first extension consists of improving the block contact algorithm. An Augmented Lagrangian Method is used to replace the Penalty Method orginally proposed. It allows Lagrange multipliers to be introduced without increasing the number of equations that need to be solved and thus, block contract forces can be calculated more accurately. A block fracturing capability based on a three-parameter Mohr-Coulomb criterion represents the second extension. It allows for shear or tensile fracturing of intact blocks and the formation of smaller blocks

  13. Effects of explosions in hard rocks

    International Nuclear Information System (INIS)

    Heuze, F.E.; Walton, O.R.; Maddix, D.M.; Shaffer, R.J.; Butkovich, T.R.

    1993-01-01

    This work relates to explosions in hard rocks (ex: basalt, granite, limestone...). Hard rock masses typically have a blocky structure created by the existence of geologic discontinuities such as bedding contacts, faults, and joints. At very high pressure - hundreds of kilobars and above - these discontinuities do not act separately, and the rock appears to be an equivalent continuous medium. At stress of a few tens of kilobars and below, the geologic discontinuities control the kinematics of the rock masses. Hence, the simulation of rock dynamics, anywhere but in the very-near source region, should account for those kinematics

  14. Regularization by Functions of Bounded Variation and Applications to Image Enhancement

    International Nuclear Information System (INIS)

    Casas, E.; Kunisch, K.; Pola, C.

    1999-01-01

    Optimization problems regularized by bounded variation seminorms are analyzed. The optimality system is obtained and finite-dimensional approximations of bounded variation function spaces as well as of the optimization problems are studied. It is demonstrated that the choice of the vector norm in the definition of the bounded variation seminorm is of special importance for approximating subspaces consisting of piecewise constant functions. Algorithms based on a primal-dual framework that exploit the structure of these nondifferentiable optimization problems are proposed. Numerical examples are given for denoising of blocky images with very high noise

  15. Ceramic Materials Selection of Fuel Crucibles based on Plasma Spray Coating for SFR

    Energy Technology Data Exchange (ETDEWEB)

    Song, Hoon; Kim, Jonghwan; Kim, Hyungtae; Ko, Youngmo; Woo, Yoonmyung; Oh, Seokjin; Kim, Kihwan; Lee, Chanbock [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2012-07-01

    The plasma-sprayed coating can provide the crucible with a denser, more friable coating layer, compared with the more friable coating layer formed by slurry-coating, which was used to prevent the interaction between melt and crucibles. Plasma-sprayed coatings are consolidated by mechanical interlocking of the molten particles impacting on the substrate and are dense by the heat applied by the plasma. The increased coating density is advantageous because it should not require frequent re coating and U-Zr melt penetration through the protective layer is more difficult in a dense coating than in a porous coating. In this study, we used Vacuum Plasma Spray method to investigate permanent coatings for re-usable crucibles for melting and casting of metallic fuel onto niobium substrates. Niobium was selected as a substrate because of its refractory nature and the coefficient of thermal expansion is similar to that of many of the candidate materials. After the HfC, ZrC, TiC, TaC, Y{sub 2}O{sub 3}, and 8% YSZ coatings were applied the resulting microstructure and chemical compositions was characterized to find the optimum process conditions for coating. Thermal plasma-sprayed coatings of refractory materials can be applied to develop a re-usable crucible coating for metallic fuel, such as the U-Zr alloy proposed for sodium cooled fast reactors.

  16. Isozyme modifications and plant regeneration through somatic embryogenesis in sweet potato (Ipomoea batatas (L.) Lam.).

    Science.gov (United States)

    Cavalcante Alves, J M; Sihachakr, D; Allot, M; Tizroutine, S; Mussio, I; Servaes, A; Ducreux, G

    1994-05-01

    The potential of somatic embryogenesis was evaluated for 10 cultivars of sweet potato through extensive embryogenic response and isozyme analysis. Embryogenic callus was induced by incubating lateral buds on Murashige and Skoog medium containing 10 μM 2,4-dichlorophenoxyacetic acid for 6-8 weeks. The frequency of embryogenic response was low, and varied with genotypes, ranging from 0 to 17%. Embryo to plantlet formation could be enhanced by the use of the combination of 2,4-dichlorophenoxyacetic acid with kinetin, both used at 0.01 μM. Embryogenic callus with its potential of plantlet formation has constantly been maintained for over two years. However, after several subcultures, 0.5 to 12% of embryogenic callus reverted irreversibly into friable fast-growing non-embryogenic callus whose ability to regenerate shoots was then definitively lost. The isozymes of esterase, peroxidase, glutamate oxaloacetate transaminase and acid phosphatase investigated in this study were found appropriate to distinguish compact embryogenic from friable non-embryogenic callus in sweet potato. In fact, the callus reversion was associated with a loss of bands or a decline in isozyme activity. On the contrary, very small changes in isozyme activity or no specific changes at all were observed during the differentiation of embryogenic callus into globular embryos.

  17. Somatic embryogenesis of East Kalimantan local upland rice varieties

    Science.gov (United States)

    Nurhasanah; Ramitha; Supriyanto, B.; Sunaryo, W.

    2018-04-01

    Somatic embryogenesis is the formation, growth and development of embryos from somatic cells. Somatic embryo induction is one of the in vitro plant propagation techniques that is very important for plant developmental purposes. Four local upland rice varieties of East Kalimantan, Mayas Pancing, Gedagai, Siam and Serai, were used in this study. A total of 200 explants (mature rice grains) for each varieties were inoculated on MS solid medium supplemented with 1 mg L-1 2,4 Dichlorophenoxy acetic acid (2,4-D) and 0.5 mg L-1 6-Benzylaminopurine (BAP). The results showed that response of each variety differed to embryosomatic induction, indicated by callus induction rate and callus quality, in terms of callus color and structure. The fastest callus formation was sobserved in Gedagai variety (8 days) while Mayas Pancing (13 days) was the latest one. The rate of callus induction varied from 60 to 98.5 %, and Serai variety has the highest callus induction rate. The highest friable callus structure was found in Siam variety (89.1%) and the lowest was in Gedagai (62.5%). Callus color was dominated by the yellowish-white (transparent) on all varieties tested. Most of the callus was potential as embryogenic callus characterized from the nodular and globular of friable callus structure and its yellowish-white color.

  18. Effect of medium composition and explant size on embryogenic calli formation of cassava (Manihot esculenta Crantz local genotypes

    Directory of Open Access Journals (Sweden)

    ENNY SUDARMONOWATI

    2006-07-01

    Full Text Available Cassava (Manihot esculenta Crantz is an important tropical crop species used for human consumption, feed and raw material for various industries. Genetic transformation through embryogenic tissues is known as an effective method for cassava genetic improvements. Objective of this study was to obtain a suitable medium and length of explants to induce embryogenic callus on friable embryogenic callus (FEC as a target for genetic transformation. Immature leaf lobes (1-3 mm, 3-5 mm and larger than 5 mm in length of local genotypes of cassava (Adira 4. Menti, Iding, Gebang, Rawi and Timtim-29 cultured in vitro were used as explants. The explants were incubated for 2 and 4 weeks on MS (Murashige-Skoog or GD (Greshooff & Doy semi solid medium containing 10 mg/L picloram, 6 mg/L NAA supplemented with 4% sucrose and 4 µM CuSO4. Results showed that the highest percentage (100% of embryogenic calli formation for 4 weeks obtained by culturing Iding of 3-5 mm length on GD semi solid medium, whereas the lowest (33% one obtained by incubation 5 mm leaf lobe of Timtim-29 on the same medium. The most suitable medium for callus induction was GD, whereas the optimum length of explants was 5 mm or larger. Further study needs to be done to obtain friable embryogenic calli (FEC by employing different concentration of picloram and varying other critical factors.

  19. CAVITY LIKE COMPLETIONS IN WEAK SANDS PREFERRED UPSTREAM MANAGEMENT PRACTICES

    Energy Technology Data Exchange (ETDEWEB)

    Ian Palmer; John McLennan

    2004-04-30

    The technology referred to as Cavity Like Completions (CLC) offers a new technique to complete wells in friable and unconsolidated sands. A successfully designed CLC provides significant increases in well PI (performance index) at lower costs than alternative completion techniques. CLC technology is being developed and documented by a partnership of major oil and gas companies through a GPRI (Global Petroleum Research Institute) joint venture. Through the DOE-funded PUMP program, the experiences of the members of the joint venture will be described for other oil and gas producing companies. To date six examples of CLC completions have been investigated by the JV. The project was performed to introduce a new type of completion (or recompletion) technique to the industry that, in many cases, offers a more cost effective method to produce oil and gas from friable reservoirs. The project's scope of work included: (1) Further develop theory, laboratory and field data into a unified model to predict performance of cavity completion; (2) Perform at least one well test for cavity completion (well provided by one of the sponsor companies); (3) Provide summary of geo-mechanical models for PI increase; and (4) Develop guidelines to evaluate success of potential cavity completion. The project tracks the experiences of a joint industry consortium (GPRI No. 17) over a three year period and compiles results of the activities of this group.

  20. Drying of upper peat of a low degree of separation in a vibro-boiling layer

    Energy Technology Data Exchange (ETDEWEB)

    Naumovich, V M; Goryachev, V I; Shafeyev, R S

    1981-01-01

    The boiling layer created by a gas flow in its motion upward through friable material finds wide application for the drying of different dispersed materials. In spite of the significant superiority of a boiling layer to other methods of drying, it is not universal and possesses a series of important drawbacks. For an intensification of the boiling layer and an upgrading of its structure, different mechanical systems are employed: agitators, impulses, ultrasound, and other actions on the material. In particular with the development of the vibration technique, vibrated low-frequency oscillations are not only a means of structurally upgrading the boiling layer, but serve as the basic factor in creating an intensively blended layer of friable material. According to the character of the motion of the particles, such a layer resembles a boiling liquid. Therefore, in the given case, it is called vibro-boiling. An appartus working on the principle of a vibro-boiling layer, in many cases, is eliminated of faults, a characteristic worthy of considering by installations with a boiling layer. A considered created department of machines and processes of refining peat, the KPI, is a vibration-drying installatin of the VSU type, designed for the drying of peat with a low degree of separation in a vibro-boiling layer.

  1. RCRA Part A and Part B Permit Application for Waste Management Activities at the Nevada Test Site: Proposed Mixed Waste Disposal Unit (MWSU)

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Management

    2010-07-19

    The proposed Mixed Waste Storage Unit (MWSU) will be located within the Area 5 Radioactive Waste Management Complex (RWMC). Existing facilities at the RWMC will be used to store low-level mixed waste (LLMW). Storage is required to accommodate offsite-generated LLMW shipped to the Nevada Test Site (NTS) for disposal in the new Mixed Waste Disposal Unit (MWDU) currently in the design/build stage. LLMW generated at the NTS (onsite) is currently stored on the Transuranic (TRU) Pad (TP) in Area 5 under a Mutual Consent Agreement (MCA) with the Nevada Division of Environmental Protection, Bureau of Federal Facilities (NDEP/BFF). When the proposed MWSU is permitted, the U.S. Department of Energy (DOE) will ask that NDEP revoke the MCA and onsite-generated LLMW will fall under the MWSU permit terms and conditions. The unit will also store polychlorinated biphenyl (PCB) waste and friable and non-friable asbestos waste that meets the acceptance criteria in the Waste Analysis Plan (Exhibit 2) for disposal in the MWDU. In addition to Resource Conservation and Recovery Act (RCRA) requirements, the proposed MWSU will also be subject to Department of Energy (DOE) orders and other applicable state and federal regulations. Table 1 provides the metric conversion factors used in this application. Table 2 provides a list of existing permits. Table 3 lists operational RCRA units at the NTS and their respective regulatory status.

  2. A novel permanently magnetised high gradient magnetic filter using assisted capture for fine particles

    Energy Technology Data Exchange (ETDEWEB)

    Watson, J.H.P. [Univ. of Southampton (United Kingdom)

    1995-02-01

    This paper describes the structure and properties of a novel permanently magnetised magnetic filter for fine friable radioactive material. Previously a filter was described and tested. This filter was designed so that the holes in the filter are left open as capture proceeds which means the pressure drop builds up only slowly. This filter is not suitable for friable composite particles which can be broken by mechanical forces. The structure of magnetic part of the second filter has been changed so as to strongly capture particles composed of fine particles weakly bound together which tend to break when captured. This uses a principle of assisted-capture in which coarse particles aid the capture of the fine fragments. The technique has the unfortunate consequence that the pressure drop across the filter rises faster as capture capture proceeds than the filter described previously. These filters have the following characteristics: (1) No external magnet is required. (2) No external power is required. (3) Small is size and portable. (4) Easily interchangeable. (5) Can be cleaned without demagnetising.

  3. RCRA Part A and Part B Permit Application for Waste Management Activities at the Nevada Test Site: Proposed Mixed Waste Disposal Unit (MWSU)

    International Nuclear Information System (INIS)

    2010-01-01

    The proposed Mixed Waste Storage Unit (MWSU) will be located within the Area 5 Radioactive Waste Management Complex (RWMC). Existing facilities at the RWMC will be used to store low-level mixed waste (LLMW). Storage is required to accommodate offsite-generated LLMW shipped to the Nevada Test Site (NTS) for disposal in the new Mixed Waste Disposal Unit (MWDU) currently in the design/build stage. LLMW generated at the NTS (onsite) is currently stored on the Transuranic (TRU) Pad (TP) in Area 5 under a Mutual Consent Agreement (MCA) with the Nevada Division of Environmental Protection, Bureau of Federal Facilities (NDEP/BFF). When the proposed MWSU is permitted, the U.S. Department of Energy (DOE) will ask that NDEP revoke the MCA and onsite-generated LLMW will fall under the MWSU permit terms and conditions. The unit will also store polychlorinated biphenyl (PCB) waste and friable and non-friable asbestos waste that meets the acceptance criteria in the Waste Analysis Plan (Exhibit 2) for disposal in the MWDU. In addition to Resource Conservation and Recovery Act (RCRA) requirements, the proposed MWSU will also be subject to Department of Energy (DOE) orders and other applicable state and federal regulations. Table 1 provides the metric conversion factors used in this application. Table 2 provides a list of existing permits. Table 3 lists operational RCRA units at the NTS and their respective regulatory status.

  4. An efficient method for in vitro callus induction in Myrciaria dubia (Kunth Mc Vaugh "Camu Camu"

    Directory of Open Access Journals (Sweden)

    Ana M. Córdova

    2014-03-01

    Full Text Available Due to the high variability in vitamin C production in Myrciaria dubia "camu camu", biotechnological procedures are necessary for mass clonal propagation of promising genotypes of this species. The aim was to establish an efficient method for in vitro callus induction from explants of M. dubia. Leaf and knot sex plants were obtained from branches grown in the laboratory and from fruit pulp collected in the field. These were desinfected and sown on Murashige-Skoog (1962 medium supplemented with 2,4-dichlorophenoxyacetic acid (2,4-D, benzylaminopurine (BAP and kinetin(Kin. The cultures were maintained at 25±2°C in darkness for 2 weeks and subsequently with a photoperiod of 16 hours in light and 8 hours in dark for 6 weeks. Treatment with 2 mg/L 2,4-D and 0.1 mg/L BAP allowed major callus formation in the three types of explants. Calluswere generated from the first week (knots, fourth week (leaves and sixth week (pulp and these were friable (leaves and nodes and non-friable (pulp. In conclusion, the described method is efficient for in vitro callus induction in leaves, knots and pulp of M. dubia, been leaves and knots explants more suitable for callus obtention

  5. Effects of retained austenite volume fraction, morphology, and carbon content on strength and ductility of nanostructured TRIP-assisted steels

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Y.F., E-mail: shenyf@smm.neu.edu.cn [Key Laboratory for Anisotropy and Texture of Materials (MOE), Northeastern University, 3 Wenhua Road, Shenyang 110004 (China); Qiu, L.N. [Key Laboratory for Anisotropy and Texture of Materials (MOE), Northeastern University, 3 Wenhua Road, Shenyang 110004 (China); Sun, X. [Pacific Northwest National Laboratory, PO Box 999, Richland, WA 99352 (United States); Zuo, L. [Key Laboratory for Anisotropy and Texture of Materials (MOE), Northeastern University, 3 Wenhua Road, Shenyang 110004 (China); Liaw, P.K. [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN 37996 (United States); Raabe, D. [Max-Planck-Institut fuer Eisenforschung, Max-Planck-Str. 1, 8, 40237 Düsseldorf (Germany)

    2015-06-11

    With a suite of multi-modal and multi-scale characterization techniques, the present study unambiguously proves that a substantially-improved combination of ultrahigh strength and good ductility can be achieved by tailoring the volume fraction, morphology, and carbon content of the retained austenite (RA) in a transformation-induced-plasticity (TRIP) steel with the nominal chemical composition of 0.19C–0.30Si–1.76Mn–1.52Al (weight percent, wt%). After intercritical annealing and bainitic holding, a combination of ultimate tensile strength (UTS) of 1100 MPa and true strain of 50% has been obtained, as a result of the ultrafine RA lamellae, which are alternately arranged in the bainitic ferrite around junction regions of ferrite grains. For reference, specimens with a blocky RA, prepared without the bainitic holding, yield a low ductility (35%) and a low UTS (800 MPa). The volume fraction, morphology, and carbon content of RA have been characterized using various techniques, including the magnetic probing, scanning electron microscopy (SEM), electron-backscatter-diffraction (EBSD), and transmission electron microscopy (TEM). Interrupted tensile tests, mapped using EBSD in conjunction with the kernel average misorientation (KAM) analysis, reveal that the lamellar RA is the governing microstructure component responsible for the higher mechanical stability, compared to the blocky one. By coupling these various techniques, we quantitatively demonstrate that in addition to the RA volume fraction, its morphology and carbon content are equally important in optimizing the strength and ductility of TRIP-assisted steels.

  6. Near-liquidus forging, partial remelting and thixoforging of an AZ91D + Y magnesium alloy

    International Nuclear Information System (INIS)

    Zhao Zude; Chen Qiang; Hu Chuankai; Huang Shuhai; Wang Yuanqing

    2009-01-01

    A new route, near-liquidus forging plus partial remelting, has been developed for obtaining globular microstructures. Firstly, a material is formed by near-liquidus forging for obtaining a fine dendritic microstructure. Globular microstructure can be produced by reheating the material into the semi-solid temperature range for a period of time. In this paper, an AZ91D alloy with the addition of yttrium was prepared by near-liquidus forging. Microstructure evolution during partial remelting was studied at temperatures and for times. Tensile mechanical properties of thixoforged components were also determined. It is shown that the fine dendritic structure firstly evolves into a blocky structure during partial remelting. With prolonged holding time, the blocky structure disintegrates into polygonal solid particles. Prolonging time and increasing temperature promote a faster spheroidization. Good mechanical properties are obtained for the thixoforged AZ91D alloy with the addition of yttrium prepared by near-liquidus forging, with a yield strength of 160.9 MPa and a ultimate tensile strength of 301.7 MPa and a elongation to fracture of 9.734%.

  7. Growth study and photocatalytic properties of Co-doped tungsten oxide mesocrystals

    International Nuclear Information System (INIS)

    Sun, Shibin; Chang, Xueting; Li, Zhenjiang

    2012-01-01

    Cobalt-doped tungsten oxide mesocrystals with different morphologies have been successfully generated using a solvothermal method with tungsten hexachloride and cobalt chloride salts as precursors. The resulting mesocrystals were characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, Brunauer–Emmet–Teller analysis of nitrogen sorptometer, and UV–vis diffuse reflectance spectroscopy. The photocatalytic properties of the cobalt-doped tungsten oxide mesocrystals were evaluated on the basis of their ability to degrade methyl orange in an aqueous solution under simulated sunlight irradiation. Results showed that the cobalt doping had obvious effect on the morphologies of the final products, and lenticular and blocky cobalt-doped tungsten oxide mesocrystals could be obtained with 1.0 wt.% and 2.0 wt.% cobalt doping, respectively. The cobalt-doped tungsten oxides exhibited superior photocatalytic activities to that of the undoped tungsten oxide. - Graphical abstract: Schematic illustrations of the growth of the bundled nanowires, lenticular mesocrystals, and blocky mesocrystals. Highlights: ► Co-doped W 18 O 49 mesocrystals were synthesized using a solvothermal method. ► The Co doping has obvious effect on the morphology of the final mesocrystals. ► The Co-doped W 18 O 49 exhibited superior photocatalytic activity to the undoped W 18 O 49 .

  8. Growth study and photocatalytic properties of Co-doped tungsten oxide mesocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Shibin [College of Logistics Engineering, Shanghai Maritime University, Shanghai 200135 (China); College of Electromechanical Engineering, Qingdao University of Science and Technology, Qingdao 266061 (China); Chang, Xueting, E-mail: xuetingchang@yahoo.cn [College of Logistics Engineering, Shanghai Maritime University, Shanghai 200135 (China); Li, Zhenjiang [College of Electromechanical Engineering, Qingdao University of Science and Technology, Qingdao 266061 (China)

    2012-11-15

    Cobalt-doped tungsten oxide mesocrystals with different morphologies have been successfully generated using a solvothermal method with tungsten hexachloride and cobalt chloride salts as precursors. The resulting mesocrystals were characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, Brunauer-Emmet-Teller analysis of nitrogen sorptometer, and UV-vis diffuse reflectance spectroscopy. The photocatalytic properties of the cobalt-doped tungsten oxide mesocrystals were evaluated on the basis of their ability to degrade methyl orange in an aqueous solution under simulated sunlight irradiation. Results showed that the cobalt doping had obvious effect on the morphologies of the final products, and lenticular and blocky cobalt-doped tungsten oxide mesocrystals could be obtained with 1.0 wt.% and 2.0 wt.% cobalt doping, respectively. The cobalt-doped tungsten oxides exhibited superior photocatalytic activities to that of the undoped tungsten oxide. - Graphical abstract: Schematic illustrations of the growth of the bundled nanowires, lenticular mesocrystals, and blocky mesocrystals. Highlights: Black-Right-Pointing-Pointer Co-doped W{sub 18}O{sub 49} mesocrystals were synthesized using a solvothermal method. Black-Right-Pointing-Pointer The Co doping has obvious effect on the morphology of the final mesocrystals. Black-Right-Pointing-Pointer The Co-doped W{sub 18}O{sub 49} exhibited superior photocatalytic activity to the undoped W{sub 18}O{sub 49}.

  9. Microstructural characterization of 5-9% chromium reduced-activation steels

    Energy Technology Data Exchange (ETDEWEB)

    Jayaram, R. [Univ. of Pittsburgh, PA (United States); Klueh, R.L. [Oak Ridge National Lab., TN (United States)

    1997-08-01

    The microstructures of a 9Cr-2W-0.25-0.1C (9Cr-2WV), a 9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa), a 7Cr-2W-0.25V-0.07Ta-0.1C (7Cr-2WVTa), and a 5Cr-2W-0.25V-0.07Ta-0.1C (5Cr-2WVTa) steel (all compositions are in weight percent) have been characterized by Analytical Electron Microscopy (AEM) and Atom Probe Field Ion Microscopy (APFIM). The matrix in all four reduced-activation steels was 100% martensite. In the two 9Cr steels, the stable precipitates were blocky M{sub 23}C{sub 6} and small spherical MC. The two lower-chromium steels contained blocky M{sub 7}C{sub 3} and small needle-shaped carbonitrides in addition to M{sub 23}C{sub 6}. AEM and APFIM analysis revealed that in the steels containing tantalum, the majority of the tantalum was in solid solution. The experimental observations were in good agreement with phases and compositions predicted by phase equilibria calculations.

  10. Centrifugally cast Zn-27Al-xMg-ySi alloys and their in situ (Mg2Si + Si)/ZA27 composites

    International Nuclear Information System (INIS)

    Wang Qudong; Chen Yongjun; Chen Wenzhou; Wei Yinhong; Zhai Chunquan; Ding Wenjiang

    2005-01-01

    Effects of composition, mold temperature, rotating rate and modification on microstructure of centrifugally cast Zn-27Al-xMg-ySi alloys have been investigated. In situ composites of Zn-27Al-6.3Mg-3.7Si and Zn-27Al-9.8Mg-5.2Si alloys were fabricated by centrifugal casting using heated permanent mold. These composites consist of three layers: inner layer segregates lots of blocky primary Mg 2 Si and a litter blocky primary Si, middle layer contains without primary Mg 2 Si and primary Si, outer layer contains primary Mg 2 Si and primary Si. The position, quantity and distribution of primary Mg 2 Si and primary Si in the composites are determined jointly by alloy composition, solidification velocity under the effect of centrifugal force and their floating velocity inward. Na salt modifier can refine grain and primary Mg 2 Si and make primary Mg 2 Si distribute more evenly and make primary Si nodular. For centrifugally cast Zn-27Al-3.2Mg-1.8Si alloy, the microstructures of inner layer, middle layer and outer layer are almost similar, single layer materials without primary Mg 2 Si and primary Si are obtained, and their grain sizes increased with the mold temperature increasing

  11. Microstructural response to heat affected zone cracking of prewelding heat-treated Inconel 939 superalloy

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, M.A., E-mail: mgonzalez@comimsa.com.mx [Facultad de Ingenieria Mecanica y Electrica (FIME-UANL), Av. Universidad s/n. Ciudad Universitaria, C.P.66451 San Nicolas de los Garza, N.L. (Mexico); Martinez, D.I., E-mail: dorairma@yahoo.com [Facultad de Ingenieria Mecanica y Electrica (FIME-UANL), Av. Universidad s/n. Ciudad Universitaria, C.P.66451 San Nicolas de los Garza, N.L. (Mexico); Perez, A., E-mail: betinperez@hotmail.com [Facultad de Ingenieria Mecanica y Electrica (FIME-UANL), Av. Universidad s/n. Ciudad Universitaria, C.P.66451 San Nicolas de los Garza, N.L. (Mexico); Guajardo, H., E-mail: hguajardo@frisa.com [FRISA Aerospace, S.A. de C.V., Valentin G. Rivero No. 200, Col. Los Trevino, C.P. 66150, Santa Caterina N.L. (Mexico); Garza, A., E-mail: agarza@comimsa.com [Corporacion Mexicana de Investigacion en Materiales S.A. de C.V. (COMIMSA), Ciencia y Tecnologia No.790, Saltillo 400, C.P. 25295 Saltillo Coah. (Mexico)

    2011-12-15

    The microstructural response to cracking in the heat-affected zone (HAZ) of a nickel-based IN 939 superalloy after prewelding heat treatments (PWHT) was investigated. The PWHT specimens showed two different microstructures: 1) spherical ordered {gamma} Prime precipitates (357-442 nm), with blocky MC and discreet M{sub 23}C{sub 6} carbides dispersed within the coarse dendrites and in the interdendritic regions; and 2) ordered {gamma} Prime precipitates in 'ogdoadically' diced cube shapes and coarse MC carbides within the dendrites and in the interdendritic regions. After being tungsten inert gas welded (TIG) applying low heat input, welding speed and using a more ductile filler alloy, specimens with microstructures consisting of spherical {gamma} Prime precipitate particles and dispersed discreet MC carbides along the grain boundaries, displayed a considerably improved weldability due to a strong reduction of the intergranular HAZ cracking associated with the liquation microfissuring phenomena. - Highlights: Black-Right-Pointing-Pointer Homogeneous microstructures of {gamma} Prime spheroids and discreet MC carbides of Ni base superalloys through preweld heat treatments. Black-Right-Pointing-Pointer {gamma} Prime spheroids and discreet MC carbides reduce the intergranular HAZ liquation and microfissuring of Nickel base superalloys. Black-Right-Pointing-Pointer Microstructure {gamma} Prime spheroids and discreet blocky type MC carbides, capable to relax the stress generated during weld cooling. Black-Right-Pointing-Pointer Low welding heat input welding speeds and ductile filler alloys reduce the HAZ cracking susceptibility.

  12. Site-specific atomic-scale characterisation of retained austenite in a strip cast TRIP steel

    International Nuclear Information System (INIS)

    Xiong, Z.P.; Saleh, A.A.; Marceau, R.K.W.; Taylor, A.S.; Stanford, N.E.; Kostryzhev, A.G.; Pereloma, E.V.

    2017-01-01

    Knowledge of carbon content in retained austenite (RA) with different neighbouring phases is essential to understand the chemical stability of RA, which is useful for microstructure tuning of transformation-induced plasticity (TRIP) steels. The present study investigates different morphologies and chemical compositions of RA by correlating electron backscattering diffraction, transmission electron microscopy and atom probe tomography. The effect of neighbouring phases, such as polygonal ferrite, bainitic ferrite lath, ferrite in granular bainite and carbides, on the carbon content in the RA is investigated. The results reveal that the film RA morphology does not always have a higher carbon content than the blocky RA; as coarse RA sometimes displays a higher carbon content than the fine RA films or islands depending on the neighbouring phases. The diffusion of carbon and manganese between austenite and ferrite in bainitic ferrite/granular bainite has been explained according to either diffusionless and/or diffusional mechanism of bainitic ferrite formation followed by tempering. -- Highlights: •The effect of neighbouring phases on retained austenite (RA) features was investigated. •A lower carbon content in fine/film RA compared to coarse/blocky RA was experimentally demonstrated. •At least locally controlled diffusion of substitutional solutes across the RA/bainitic ferrite lath interface was suggested.

  13. Fission dynamics of 240Cf* formed in 34,36S induced reactions

    Directory of Open Access Journals (Sweden)

    Jain Deepika

    2015-01-01

    Full Text Available We have studied the entrance channel effects in the decay of Compound nucleus 240Cf* formed in 34S+206Pb and 36S+204Pb reactions by using energy density dependent nuclear proximity potential in the framework of dynamical cluster-decay model (DCM. At different excitation energies, the fragmentation potential and preformation probability of decaying fragments are almost identical for both the entrance channels, which seem to suggest that decay is independent of its formation and entrance channel excitation energy. It is also observed that, with inclusion of deformation effects upto quadrupole within the optimum orientation approach, the fragmentation path governing potential energy surfaces gets modified significantly. Beside this, the fission mass distribution of Cf* isotopes is also investigated. The calculated fission cross-sections using SIII force for both the channels find nice agreement with the available experimental data for deformed choice of fragments, except at higher energies. In addition to this, the comparative analysis with Blocki based nuclear attraction is also worked out. It is observed that Blocki proximity potential accounts well for the CN decay at all energies whereas the use of EDF based nuclear potential suggests the presence of some non-compound nucleus process (such as quasi-fission (qf at higher energies.

  14. A study of Ni-based WC composite coatings by laser induction hybrid rapid cladding with elliptical spot

    International Nuclear Information System (INIS)

    Zhou Shengfeng; Huang Yongjun; Zeng Xiaoyan

    2008-01-01

    Ni-based WC composite coatings by laser induction hybrid rapid cladding (LIHRC) with elliptical spot were investigated. Results indicate that the efficiency using the elliptical spot of 6 mm x 4 mm (the major and minor axis of laser beam are 6 mm and 4 mm, respectively, the major axis is parallel to the direction of laser scanning) is higher than that using the elliptical spot of 4 mm x 6 mm (the major axis is perpendicular to the direction of laser scanning). The precipitated carbides with the blocky and bar-like shape indicate that WC particles suffer from the heat damage of 'the disintegration pattern + the growth pattern', whichever elliptical spot is used at low laser scanning speed. However, at high laser scanning speed, the blocky carbides are only formed if the elliptical spot of 6 mm x 4 mm is adopted, showing that WC particles present the heat damage of 'the disintegration pattern', whereas the fine carbides are precipitated when the elliptical spot of 4 mm x 6 mm is used, showing that WC particles take on the heat damage of 'the radiation pattern'. Especially, the efficiency of LIHRC is increased much four times higher than that of the general laser cladding and crack-free ceramic-metal coatings can be obtained

  15. Improved Discrimination of Volcanic Complexes, Tectonic Features, and Regolith Properties in Mare Serenitatis from Earth-Based Radar Mapping

    Science.gov (United States)

    Campbell, Bruce A.; Hawke, B. Ray; Morgan, Gareth A.; Carter, Lynn M.; Campbell, Donald B.; Nolan, Michael

    2014-01-01

    Radar images at 70 cm wavelength show 4-5 dB variations in backscatter strength within regions of relatively uniform spectral reflectance properties in central and northern Mare Serenitatis, delineating features suggesting lava flow margins, channels, and superposition relationships. These backscatter differences are much less pronounced at 12.6 cm wavelength, consistent with a large component of the 70 cm echo arising from the rough or blocky transition zone between the mare regolith and the intact bedrock. Such deep probing is possible because the ilmenite content, which modulates microwave losses, of central Mare Serenitatis is generally low (2-3% by weight). Modeling of the radar returns from a buried interface shows that an average regolith thickness of 10m could lead to the observed shifts in 70 cm echo power with a change in TiO2 content from 2% to 3%. This thickness is consistent with estimates of regolith depth (10-15m) based on the smallest diameter for which fresh craters have obvious blocky ejecta. The 70 cm backscatter differences provide a view of mare flow-unit boundaries, channels, and lobes unseen by other remote sensing methods. A localized pyroclastic deposit associated with Rima Calippus is identified based on its low radar echo strength. Radar mapping also improves delineation of units for crater age dating and highlights a 250 km long, east-west trending feature in northern Mare Serenitatis that we suggest is a large graben flooded by late-stage mare flows.

  16. Characterization on the Microstructure Evolution and Toughness of TIG Weld Metal of 25Cr2Ni2MoV Steel after Post Weld Heat Treatment

    Directory of Open Access Journals (Sweden)

    Xia Liu

    2018-03-01

    Full Text Available The microstructure and toughness of tungsten inert gas (TIG backing weld parts in low-pressure steam turbine welded rotors contribute significantly to the total toughness of the weld metal. In this study, the microstructure evolution and toughness of TIG weld metal of 25Cr2Ni2MoV steel low-pressure steam turbine welded rotor under different post-weld heat treatment (PWHT conditions are investigated. The fractography and microstructure of weld metal after PWHT are characterized by optical microscope, SEM, and TEM, respectively. The Charpy impact test is carried out to evaluate the toughness of the weld. The optical microscope and SEM results indicate that the as-welded sample is composed of granular bainite, acicular ferrite and blocky martensite/austenite (M-A constituent. After PWHT at 580 °C, the blocky M-A decomposes into ferrite and carbides. Both the number and size of precipitated carbides increase with holding time. The impact test results show that the toughness decreases dramatically after PWHT and further decreases with holding time at 580 °C. The precipitated carbides are identified as M23C6 carbides by TEM, which leads to the dramatic decrease in the toughness of TIG weld metal of 25Cr2Ni2MoV steel.

  17. Fast Extended Depth-of-Field Reconstruction for Complex Holograms Using Block Partitioned Entropy Minimization

    Directory of Open Access Journals (Sweden)

    Peter Wai Ming Tsang

    2018-05-01

    Full Text Available Optical scanning holography (OSH is a powerful and effective method for capturing the complex hologram of a three-dimensional (3-D scene. Such captured complex hologram is called optical scanned hologram. However, reconstructing a focused image from an optical scanned hologram is a difficult issue, as OSH technique can be applied to acquire holograms of wide-view and complicated object scenes. Solutions developed to date are mostly computationally intensive, and in so far only reconstruction of simple object scenes have been demonstrated. In this paper we report a low complexity method for reconstructing a focused image from an optical scanned hologram that is representing a 3-D object scene. Briefly, a complex hologram is back-propagated onto regular spaced images along the axial direction, and from which a crude, blocky depth map of the object scene is computed according to non-overlapping block partitioned entropy minimization. Subsequently, the depth map is low-pass filtered to decrease the blocky distribution, and employed to reconstruct a single focused image of the object scene for extended depth of field. The method proposed here can be applied to any complex holograms such as those obtained from standard phase-shifting holography.

  18. Influence of TiO2 content on the crystallization and microstructure of machinable glass-ceramics

    Directory of Open Access Journals (Sweden)

    Debasis Pradip Mukherjee

    2016-03-01

    Full Text Available Glasses based on the SiO2–Al2O3–MgO–K2O–B2O3–MgF2 system added with TiO2 were synthesized and characterized by differential scanning calorimetry (DSC, X-ray powder diffraction (XRD, Fourier transform infrared spectroscopy (FTIR and scanning electron microscopy (SEM techniques. The results showed that by increasing the TiO2 content, glass transition temperature (Tg, both the crystallization peak temperature (TpI and TpII and activation energy (E increased. The interconnected large blocky card-like crystals were identified as fluorophlogopite as a major crystalline phase for all three glass-ceramic specimens by (XRD and subsequently confirmed by SEM. The Vickers hardness (Hv value for glass-ceramic specimens decreases with progressively increasing TiO2 content (1–10 wt% and Titania containing MGT-3 glass-ceramic specimen with interconnected large blocky card-like fluorophlogopite mica crystals possess lower Hv (4.26 GPa as well as good machinability (m = 0.12 useable for machinable applications. The study shows that Titania promoted initial crystallization of glass and can be used as an effective nucleting agent.

  19. Microstructural characterization of 5-9% chromium reduced-activation steels

    International Nuclear Information System (INIS)

    Jayaram, R.; Klueh, R.L.

    1997-01-01

    The microstructures of a 9Cr-2W-0.25-0.1C (9Cr-2WV), a 9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa), a 7Cr-2W-0.25V-0.07Ta-0.1C (7Cr-2WVTa), and a 5Cr-2W-0.25V-0.07Ta-0.1C (5Cr-2WVTa) steel (all compositions are in weight percent) have been characterized by Analytical Electron Microscopy (AEM) and Atom Probe Field Ion Microscopy (APFIM). The matrix in all four reduced-activation steels was 100% martensite. In the two 9Cr steels, the stable precipitates were blocky M 23 C 6 and small spherical MC. The two lower-chromium steels contained blocky M 7 C 3 and small needle-shaped carbonitrides in addition to M 23 C 6 . AEM and APFIM analysis revealed that in the steels containing tantalum, the majority of the tantalum was in solid solution. The experimental observations were in good agreement with phases and compositions predicted by phase equilibria calculations

  20. Eutectic Al-Si-Cu-Fe-Mn alloys with enhanced mechanical properties at room and elevated temperature

    International Nuclear Information System (INIS)

    Wang, E.R.; Hui, X.D.; Chen, G.L.

    2011-01-01

    Highlights: → Fabricated a kind of high performance Al-Si alloy with low production costs. → Clarified two different morphologies of α-Fe and corresponding crystal structures. → Analyzed the crystallography of Cu-rich phases before and after T6 treatment. → Fracture mechanism of precipitates in experimental alloys during tensile process. -- Abstract: In this paper, we report a novel kind of eutectic Al-Si-Cu-Fe-Mn alloy with ultimate tensile strength up to 336 MPa and 144.3 MPa at room temperature and 300 o C, respectively. This kind of alloy was prepared by metal mold casting followed by T6 treatment. The microstructure is composed of eutectic and primary Si, α-Fe, Al 2 Cu and α-Al phases. Iron-rich phases, which were identified as BCC type of α-Fe (Al 15 (Fe,Mn) 3 Si 2 ), exist in blocky and dendrite forms. Tiny blocky Al 2 Cu crystals disperse in α-Fe dendrites or at the grain boundaries of α-Al. During T6 treatment, Cu atoms aggregate from the super-saturation solid solution to form GP zones, θ'' or θ'. Further analysis found that the enhanced mechanical properties of the experimental alloy are mainly attributed to the formation of α-Fe and copper-rich phases.

  1. Remote sensing data of SP Mountain and SP Lava flow in North-Central Arizona

    Science.gov (United States)

    Schaber, G.G.; Elachi, C.; Farr, T.G.

    1980-01-01

    Multifrequency airborne radar image data of SP Mountain [Official name of feature (U.S. Geological Survey, 1970)] and SP flow (and vicinity) in north-central Arizona were obtained in diverse viewing directions and direct and cross-polarization, then compared with surface and aerial photography, LANDSAT multispectral scanner data, airborne thermal infrared imagery, surface geology, and surface roughness statistics. The extremely blocky, basaltic andesite of SP flow is significantly brighter on direct-polarization K-band (0.9-cm wavelength) images than on cross-polarized images taken simultaneously. Conversely, for the longer wavelength (25 cm) L-band radar images, the cross-polarization image returns from SP flow are brighter than the direct-polarized image. This effect is explained by multiple scattering and the strong wavelength dependence of polarization effects caused by the rectilinear basaltic andesite scatters. Two distinct types of surface relief on SP flow, one extremely blocky, the other subdued, are found to be clearly discriminated on the visible and thermal wavelength images but are separable only on the longer wavelength L-band radar image data. The inability of the K- and X- (3-cm wavelength) band radars to portray the differences in roughness between the two SP flow surface units is attributed to the radar frequency dependence of the surface-relief scale, which, described as the Rayleigh criterion, represents the transition between quasispecular and primarily diffuse backscatter. ?? 1980.

  2. Furthering the investigation of eruption styles through quantitative shape analyses of volcanic ash particles

    Science.gov (United States)

    Nurfiani, D.; Bouvet de Maisonneuve, C.

    2018-04-01

    Volcanic ash morphology has been quantitatively investigated for various aims such as studying the settling velocity of ash for modelling purposes and understanding the fragmentation processes at the origin of explosive eruptions. In an attempt to investigate the usefulness of ash morphometry for monitoring purposes, we analyzed the shape of volcanic ash particles through a combination of (1) traditional shape descriptors such as solidity, convexity, axial ratio and form factor and (2) fractal analysis using the Euclidean Distance transform (EDT) method. We compare ash samples from the hydrothermal eruptions of Iwodake (Japan) in 2013, Tangkuban Perahu (Indonesia) in 2013 and Marapi (Sumatra, Indonesia) in 2015, the dome explosions of Merapi (Java, Indonesia) in 2013, the Vulcanian eruptions of Merapi in 2010 and Tavurvur (Rabaul, Papaua New Guinea) in 2014, and the Plinian eruption of Kelud (Indonesia) in 2014. Particle size and shape measurements were acquired from a Particle Size Analyzer with a microscope camera attached to the instrument. Clear differences between dense/blocky particles from hydrothermal or dome explosions and vesicular particles produced by the fragmentation of gas-bearing molten magma are well highlighted by conventional shape descriptors and the fractal method. In addition, subtle differences between dense/blocky particles produced by hydrothermal explosions, dome explosions, or quench granulation during phreatomagmatic eruptions can be evidenced with the fractal method. The combination of shape descriptors and fractal analysis is therefore potentially able to distinguish between juvenile and non-juvenile magma, which is of importance for eruption monitoring.

  3. Premilinary studies for optimiziing a protocol for obtaining embryogenic calluses in two rubber (Hevea brasiliensis Mull. Arg clones from different geographical origins Estudios preliminares en la estandarización de un protocolo para la obtención de callos embriogénicos en dos clones de caucho (Hevea brasiliensis Müll. Arg. de diferentes orígenes geográficos

    Directory of Open Access Journals (Sweden)

    Medina S. Marisol

    2006-07-01

    Full Text Available The influence of growth regulators on obtaining friable rubber (Hevea brasiliensis Müll. Arg. calluses with no plant regeneration as investigated. Two clones having different geographical origin were used in all trails carried out in this study: FX 3864 (South-American and PB 254 (Asian. Young leaves and eight- to ten-week-old seed integument from both clones were used as explants in several experiments; they were initially cultured in MH medium (Carron, et ál., 1989, modified MH medium (Montoro, et ál., 1993, 2000 and modified MS medium (Carron, et at,. 1992, no positive response being obtained by days 25 or 50. However, other trials were carried out with the integument in modified MS medium (1962, 0.67 mg/L BAP and 0.66 mg/L 2-4 D being added as medium for initiating embryogenesis, the formation of white, friable calluses being observed by day 25 in the two selected clones. These calluses were sub-cultured in MS supplemented with 0.35 mg/L BAP and 0.2 mg/L 2-4 D as callogenesis expression medium, embryogenic expression being observed in both clones by day 50. Equally friable white calluses were obtained from young leaves in the two clones in MS medium supplemented with 1.0 mg/L BAP, 1.0 mg/L ANA but without IBA and kinetin by day 25. Calluses sub-cultured in the same medium supplemented with 0.5 mg/L BAP and 0.5 mg/L ANA began to show increased friability after 50 days. culture. This work is a partial report of a macro-project for optimising a protocol for rubber (Hevea brasiliensis  multiplication by somatic embryogenesis.Se investigó la influencia de los reguladores de crecimiento para la obtención de callos friables en caucho (Hevea brasiliensis Müll. Arg. sin llegar a obtenerse regeneración de plántulas. En todos los ensayos realizados en este estudio, se utilizaron dos clones de diferentes orígenes geográficos: el FX 3864 (suramericano y el PB 254 (asiático. Para los diferentes tratamientos se utilizaron como explantes hojas j

  4. Antisolvent precipitation of novel xylitol-additive crystals to engineer tablets with improved pharmaceutical performance.

    Science.gov (United States)

    Kaialy, Waseem; Maniruzzaman, Mohammad; Shojaee, Saeed; Nokhodchi, Ali

    2014-12-30

    The purpose of this work was to develop stable xylitol particles with modified physical properties, improved compactibility and enhanced pharmaceutical performance without altering polymorphic form of xylitol. Xylitol was crystallized using antisolvent crystallization technique in the presence of various hydrophilic polymer additives, i.e., polyethylene glycol (PEG), polyvinylpyrrolidone (PVP) and polyvinyl alcohol (PVA) at a range of concentrations. The crystallization process did not influence the stable polymorphic form or true density of xylitol. However, botryoidal-shaped crystallized xylitols demonstrated different particle morphologies and lower powder bulk and tap densities in comparison to subangular-shaped commercial xylitol. Xylitol crystallized without additive and xylitol crystallized in the presence of PVP or PVA demonstrated significant improvement in hardness of directly compressed tablets; however, such improvement was observed to lesser extent for xylitol crystallized in the presence of PEG. Crystallized xylitols produced enhanced dissolution profiles for indomethacin in comparison to original xylitol. The influence of additive concentration on tablet hardness was dependent on the type of additive, whereas an increased concentration of all additives provided an improvement in the dissolution behavior of indomethacin. Antisolvent crystallization using judiciously selected type and concentration of additive can be a potential approach to prepare xylitol powders with promising physicomechanical and pharmaceutical properties. Copyright © 2014 Elsevier B.V. All rights reserved.

  5. Karakteristik dan kandungan mineral pasir pantai Lhok Mee, Beureunut dan Leungah, Kabupaten Aceh Besar

    Directory of Open Access Journals (Sweden)

    Saniah .

    2015-02-01

    Full Text Available Abstract. The objective of this research was to determine the characteristics and mineral content of coastal sand from  Lhokmee, Beureunut, and Leungah Aceh Besar District. The sand analysis was conducted at Material Laboratory of Mathematics and Natural Sciences Faculty, Syiah Kuala University from March to April, 2014. Samples were collected using purpossive sampling method. The observed physical characteristics of this research were sand color, shape and particle size. The mineral content was analysed using X-Ray Diffraction (XRD and Joint Committee for Powder Diffraction Standard (JCPDS program. The result showed that Lhok Mee coastal sand was physically characterized as white, sub-angular rounded shape and 0.21 mm of size, while Beureunut coastal sand was light brown, rounded-well rounded shape and 0.19 mm of size, then Leungah coastal sand was black, angular-well rounded shape and 0.13 mm of size. Based on  mineral content showed that Lhok Mee, Beureunut, and Leungah coastal sand were dominated by SiO3, SO3 and Fe3O4, respectively. All identified minerals at all stations were classified as volcanic minerals of lithogenous sediment. Keywords: Beach sands; Color difference; Mineral content; Shape; Particle size.

  6. The ammonoids from the Argiles de Timimoun of Timimoun (Early and Middle Viséan; Gourara, Algeria

    Directory of Open Access Journals (Sweden)

    J. Bockwinkel

    2010-02-01

    Full Text Available Twenty-seven ammonoid species are described from the Argiles de Timimoun of Timimoun (Gourara, Algeria. The following taxa are newly described: Rhnetites n. gen., Rhnetites rhnetensis n. sp., Rhnetites ouladallalensis n. sp., Parahammatocyclus mutaris n. sp., Bollandoceras nitens n. sp., Bollandoceras subangulare n. sp., Bollandoceras politum n. sp., Bollandoceras aridum n. sp., Bollandoceras zuhara n. sp., Bollandoceras mirrih n. sp., Benimehlalites n. gen., Benimehlalites benimehlalensis n. sp., Benimehlalites belkassemensis n. sp., Benimehlalites brinkmanni n. sp., Pachybollandoceras n. gen., Pachybollandoceras intraevolutum n. sp., Pachybollandoceras repens n. sp., Bollanditinae n. subfam., Gourarites n. gen., Gourarites hagaraswad n. sp., Gourarites hagarkarim n. sp., Gourarites mustari n. sp., Gourarites zuhal n. sp., Semibollandites n. gen., Semibollandites kamil n. sp., Semibollandites pauculus n. sp., Semibollandites qawiy n. sp., Timimounia n. gen., Timimounia timimounensis n. sp., Timimounia lunula n. sp., Daaitidae n. fam., Daaites n. gen., Daaites daaensis n. sp., Dimorphoceras lanceolobatum n. sp., Nomismoceras salim n. sp., and Nomismoceras waltoni n. sp. The species occur in three successive horizons and can be attributed to the Bollandites-Bollandoceras Genus Zone (Early and Middle Viséan. They represent the most diverse ammonoid fauna known from this time interval. doi:10.1002/mmng.200900013

  7. Stratigraphy, provenance, and diagenesis of the Cretaceous Horse Range Formation, east Otago, New Zealand

    International Nuclear Information System (INIS)

    Mitchell, M.; Craw, D.; Landis, C.A.; Frew, R.

    2009-01-01

    The Horse Range Formation is a structurally controlled late Early Cretaceous to early Late Cretaceous nonmarine unit in east Otago, South Island, New Zealand, containing immature lithic debris. Clasts are generally rounded, with only minor subangular material. The formation contains clasts derived from two principal basement sources: schist and greywacke. Schist debris is most abundant at the base of the described section, and this material is dominated (>60%) by quartz from the greenschist facies core of the Otago Schist belt. Conglomerates with >70% greywacke clasts constitute most of the upper part of the Horse Range Formation. These greywacke conglomerates have a matrix of sand derived mainly from schist. A 60 m thick wedge of quartz-rich, locally carbonaceous sand occurs interlayered with greywacke conglomerates. The Horse Range Formation rests on sub-greenschist facies semischist, which forms only a small proportion ( 18 O SMOW near +24 permil and δ 13 C PDB near -2 permil, and was partly dissolved and redeposited from the immature basement debris (metamorphic calcite) and partly introduced from overlying Late Cretaceous and Teriary marine sediments by groundwater. (author). 43 refs., 11 figs., 1 tab.

  8. NATURE AND DYNAMIC OF SEDIMENTS AT THE MOUTH OF KOMOÉ RIVER (IVORY COAST

    Directory of Open Access Journals (Sweden)

    Laurent K. ADOPO

    2014-06-01

    Full Text Available Komoé River represents the most important freshwater resource of Ivory Coast. This study aims at identifying the alluvia material and its dynamic at the mouth. The agricultural activity within the upper basin has determined a decrease in liquid discharge and an increase in alluvia transport. Most of the water is used in agriculture. The alluvia material comprises mainly sands and it is included in the middle-coarse category. Mixed sediments are composed of muddy sands and sandy muds. Most quartz grains transported by the river are flattened and glassy (91.66%, while the rest are round and opaque (8.34%. Minerals are angular, subangular, rounded and subrounded. Among heavy minerals, it is worth mentioning as follows: quartz, mica, feldspar, pyroxene, tourmaline, amphibole, gamet, epidote etc. The high degree of alluvia deposit has reduced the depth of the lower river course and it has closed the estuary completely. In this case, the wetland was extended and the vegetation tends to cover the entire surface. Navigation has been made difficult by the alluvial and organic clogging processes.

  9. Sediment-infill volcanic breccia from the Neoarchean Shimoga greenstone terrane, western Dharwar Craton: Implications on pyroclastic volcanism and sedimentation in an active continental margin

    Science.gov (United States)

    Manikyamba, C.; Saha, Abhishek; Ganguly, Sohini; Santosh, M.; Lingadevaru, M.; Rajanikanta Singh, M.; Subba Rao, D. V.

    2014-12-01

    We report sediment-infill volcanic breccia from the Neoarchean Shimoga greenstone belt of western Dharwar Craton which is associated with rhyolites, chlorite schists and pyroclastic rocks. The pyroclastic rocks of Yalavadahalli area of Shimoga greenstone belt host volcanogenic Pb-Cu-Zn mineralization. The sediment-infill volcanic breccia is clast-supported and comprises angular to sub-angular felsic volcanic clasts embedded in a dolomitic matrix that infilled the spaces in between the framework of volcanic clasts. The volcanic clasts are essentially composed of alkali feldspar and quartz with accessory biotite and opaques. These clasts have geochemical characteristics consistent with that of the associated potassic rhyolites from Daginkatte Formation. The rare earth elements (REE) and high field strength element (HFSE) compositions of the sediment-infill volcanic breccia and associated mafic and felsic volcanic rocks suggest an active continental margin setting for their generation. Origin, transport and deposition of these rhyolitic clasts and their aggregation with infiltrated carbonate sediments may be attributed to pyroclastic volcanism, short distance transportation of felsic volcanic clasts and their deposition in a shallow marine shelf in an active continental margin tectonic setting where the rhyolitic clasts were cemented by carbonate material. This unique rock type, marked by close association of pyroclastic volcanic rocks and shallow marine shelf sediments, suggest shorter distance between the ridge and shelf in the Neoarchean plate tectonic scenario.

  10. Palyno-morphological characteristics of gymnosperm flora of pakistan and its taxonomic implications with LM and SEM methods.

    Science.gov (United States)

    Khan, Raees; Ul Abidin, Sheikh Zain; Ahmad, Mushtaq; Zafar, Muhammad; Liu, Jie; Amina, Hafiza

    2018-01-01

    The present study is intended to assess gymnosperms pollen flora of Pakistan using Light Microscope (LM) and Scanning Electron Microscopy (SEM) for its taxonomic significance in identification of gymnosperms. Pollens of 35 gymnosperm species (12 genera and five families) were collected from its various distributional sites of gymnosperms in Pakistan. LM and SEM were used to investigate different palyno-morphological characteristics. Five pollen types (i.e., Inaperturate, Monolete, Monoporate, Vesiculate-bisaccate and Polyplicate) were observed. Six In equatorial view seven types of pollens were observed, in which ten species were sub-angular, nine species were Traingular, six species were Perprolate, three species were Rhomboidal, three species were semi-angular, two species were rectangular and two species were prolate. While five types of pollen were observed in polar view, in which ten species were Spheroidal, nine species were Angular, eight were Interlobate, six species were Circular, two species were Elliptic. Eighteen species has rugulate and 17 species has faveolate ornamentation. Eighteen species has verrucate and 17 have gemmate type sculpturing. The data was analysed through cluster analysis. The study showed that these palyno-morphological features have significance value in classification and identification of gymnosperms. Based on these different palyno-morphological features, a taxonomic key was proposed for the accurate and fast identifications of gymnosperms from Pakistan. © 2017 Wiley Periodicals, Inc.

  11. Viking landing sites, remote-sensing observations, and physical properties of Martian surface materials

    Science.gov (United States)

    Moore, H.J.; Jakosky, B.M.

    1989-01-01

    Important problems that confront future scientific exploration of Mars include the physical properties of Martian surface materials and the geologic processes that formed the materials. The design of landing spacecraft, roving vehicles, and sampling devices and the selection of landing sites, vehicle traverses, and sample sites will be, in part, guided by the physical properties of the materials. Four materials occur in the sample fields of the Viking landers: (1) drift, (2) crusty to cloddy, (3) blocky, and (4) rock. The first three are soillike. Drift materials is weak, loose, and porous. We estimate that it has a dielectric constant near 2.4 and a thermal inertia near 1 ?? 10-3 to 3 ?? 10-3 (cal cm-2 sec 1 2 K-1) because of its low bulk density, fine grain size, and small cohesion. Crusty to cloddy material is expected to have a dielectric constant near 2.8 and a thermal inertia near 4 ?? 10-3 to 7 ?? 10-3 because of its moderate bulk density and cementation of grains. Blocky material should have a dielectric constant near 3.3 and a thermal inertia near 7 ?? 10-3 to 9 ?? 10-3 because of its moderate bulk density and cementation. Common basaltic rocks have dielectric constans near 8 and thermal inertias near 30 ?? 10-3 to 60 ?? 10-3. Comparisons of estimated dielectric constants and thermal inertias of the materials at the landing sites with those obtained remotely by Earth-based radars and Viking Orbiter thermal sensors suggest that the materials at the landing sites are good analogs for materials elsewhere on Mars. Correlation of remotely estimated dielectric constant and thermal inertias indicates two modal values for paired values of dielectric constants and thermal inertias near (A) 2 and 2 ?? 10-3 and (B) 3 and 6 ?? 10-3, respectively. These two modes are comparable to the dielectric constants and thermal inertias for drift and crusty to cloddy material, respectively. Dielectric constants and thermal inertias for blocky material are larger but conistent

  12. The Cocos Ridge hydrothermal system revealed by microthermometry of fluid and melt inclusions

    Science.gov (United States)

    Brandstätter, J.; Kurz, W.; Krenn, K.

    2017-12-01

    Microthermometric analyses of fluid and melt inclusions in hydrothermal veins and in the Cocos Ridge (CCR) basalt were used to reveal the CCR thermal history at IODP Site 344-U1414 and to constrain fluid source and flow. Hydrothermal veins are hosted by lithified sediments and CCR basalt . Site 344-U1414, located 1 km seaward of the Middle American Trench offshore Costa Rica, serves to evaluate fluid/rock interaction, the hydrologic system and geochemical processes linked with the tectonic evolution of the incoming Cocos Plate from the Early Miocene up to recent times. The veins in the sedimentary rocks are mainly filled by blocky calcite, containing numerous fluid inclusions, and sometimes crosscut fibrous quartz/chalcedony veins. The veins in the basalt can be differentiated into three types: antitaxial fibrous calcite veins, composite veins with fibrous calcite and clay minerals at the vein margins and spherulitic quartz in the center, and syntaxial blocky aragonite veins surrounded by a clay selvage in the uppermost CCR basalt sections. Secondary minerals, clay minerals, fibrous calcite, quartz/chalcedony and pyrite also filled vesicles in the basalt. Fluid inclusions were mainly found in the aragonite veins and rarely in quartz in the composite veins and vesicles. Blocky veins with embedded wall rock fragments appear in the sediments and in the basalt indicate hydraulic fracturing. The occurrence of decrepitated fluid inclusions show high homogenization temperatures up to 400 °C. Decrepitated fluid inclusions are formed by increased internal overpressure, related to isobaric heating. Elongated fluid inclusion planes, arc-like fluid inclusions and low homogenization temperatures indicate subsequent isobaric cooling. The results obtained so far from Raman spectroscopy and microthermometry indicate CO2 inclusions and petrographic observations suggest the presence of silicate melt inclusions in phenocrysts in the basalt (mainly in clinopyroxene and plagioclase

  13. Predicting the occurrence of headache and back pain in young adults by biopsychological characteristics assessed at childhood or adolescence

    Directory of Open Access Journals (Sweden)

    Kröner-Herwig B

    2017-03-01

    Full Text Available Birgit Kröner-Herwig, Anastasia Gorbunova, Jennifer Maas Department of Clinical Psychology and Psychotherapy, Georg-Elias-Müller-Institute of Psychology, University of Göttingen, Göttingen, Germany Abstract: The aim of the current study was to identify predictors of recurrent headache and back pain in young adults (aged 18–27 years from data assessed in childhood or adolescence, i.e., 9 years before the final survey. Our interest was whether psychological characteristics contribute to the risk of pain prevalence in adult age when controlling for already empirically supported risk factors such as parental pain, pediatric pain and sex. The study was part of a five-wave epidemiological investigation of >5000 families with children aged between 7 and 14 years when addressed first. In a multiple hierarchical regression analysis, the abovementioned three variables (Block-I variables were entered first followed by five psychological trait variables (Block-II variables: internalizing, anxiety sensitivity, somatosensory amplification, catastrophizing and dysfunctional stress coping to find out the extent of model improvement. The multivariable hierarchical regression analysis confirmed the hypothesis that the Block-I variables significantly enhance the risk of future pain at young adult age. None of the psychological variables did so. Thus, the hypothesis of a significant surplus predictive effect was not confirmed. The amount of total explained variance differed strongly between headache and back pain. In particular, a valid prediction of back pain was not possible. When analyzed separately in simple regression analysis, psychological variables turned out to be significant predictors, however, of very low effect size. The inclusion of Block-I variables in the model clearly reduced the impact of the psychological variables. This risk profile is discussed in the context of the different trajectories of headache and back pain from childhood to

  14. Trace elements and isotope data of the Um Garayat gold deposit, Wadi Allaqi district, Egypt

    Science.gov (United States)

    Zoheir, Basem; Emam, Ashraf; Pitcairn, Iain K.; Boskabadi, Arman; Lehaye, Yann; Cooper, Matthew J.

    2018-04-01

    Trace element composition of sulfides and O, C, Sr and S isotopic data are assessed to constrain the evolution and potential fluid and metal sources of the Um Garayat gold deposit. Ore microscopy and BSE investigations of quartz veins show blocky arsenopyrite and pyrite replaced in part by pyrrhotite, chalcopyrite, sphalerite, galena, and gersdorffite. Free-milling gold occurs commonly in close association with the late sulfides, and along fractures in pyrite. On the other hand, recrystallized pyrite is disseminated in host metavolcaniclastic/metasedimentary rocks that commonly contain carbonaceous material. In situ LA-ICP-MS analysis of sulfides shows the recrystallized pyrite enriched in most trace elements, while blocky pyrite contains only some traces of arsenic. Detected concentrations of gold (up to 17 ppm) were only reported in arsenopyrite disseminated in quartz veins. The δ34S values of blocky pyrite and pyrrhotite in quartz veins define a narrow range (1.6 to 3.7‰), suggesting a homogenous sulfur source which is consistent with the dominantly mafic host rocks. The recrystallized pyrite has a distinctive sulfur isotope composition (δ34S - 9.3 to - 10.6‰), which is rather comparable to diagenetic sulfides. Hydrothermal carbonate in quartz veins and wallrock have nearly constant values of δ18O (10.5 to 11.9‰) and δ13C (- 4.2 to - 5.5‰). Based on constraints from mineral assemblages and chlorite thermometry, data of six samples indicate that carbonate precipitation occurred at 280 °C from a homogenous hydrothermal fluid with δ18OH2O 4.4 ± 0.7‰ and δ13C = 3.7 ± 0.8‰. Strontium isotope values of two samples (87Sr/86Sr = 0.7024 and 0.7025) are similar to the initial 87Sr/86Sr ratios of island arc metabasalts ( 710 Ma) in the South Eastern Desert. The generally homogenous sulfur, C, O, Sr isotope data are suggestive of metamorphogenic fluids, likely produced from dominantly mafic volcanic rocks at the greenschist-amphibolite facies transition.

  15. Activated, coal-based carbon foam

    Science.gov (United States)

    Rogers, Darren Kenneth; Plucinski, Janusz Wladyslaw

    2004-12-21

    An ablation resistant, monolithic, activated, carbon foam produced by the activation of a coal-based carbon foam through the action of carbon dioxide, ozone or some similar oxidative agent that pits and/or partially oxidizes the carbon foam skeleton, thereby significantly increasing its overall surface area and concurrently increasing its filtering ability. Such activated carbon foams are suitable for application in virtually all areas where particulate or gel form activated carbon materials have been used. Such an activated carbon foam can be fabricated, i.e. sawed, machined and otherwise shaped to fit virtually any required filtering location by simple insertion and without the need for handling the "dirty" and friable particulate activated carbon foam materials of the prior art.

  16. Resolution of Large Azygos Vein Aneurysm Following Stent-Graft Shunt Placement in a Patient with Ehlers-Danlos Syndrome Type IV

    International Nuclear Information System (INIS)

    D'Souza, Estelle S.; Williams, David M.; Deeb, G.M.; Cwikiel, Wojciech

    2006-01-01

    Ehlers-Danlos syndrome (EDS) type IV is a rare connective tissue disorder associated with thin-walled, friable arteries and veins predisposing patients to aneurysm formation, dissection, fistula formation, and vessel rupture. Azygos vein aneurysm is an extremely rare condition which has not been reported in association with EDS in the literature. We present a patient with EDS type IV and interrupted inferior vena cava (IVC) with azygos continuation who developed an azygos vein aneurysm. In order to decrease flow through the azygos vein and reduce the risk of aneurysm rupture, a stent-graft shunt was created from the right hepatic vein to the azygos vein via a transhepatic, retroperitoneal route. At 6 month follow-up the shunt was open and the azygos vein aneurysm had resolved

  17. Research and development to prepare and characterize robust coal/biomass mixtures for direct co-feeding into gasification systems

    Energy Technology Data Exchange (ETDEWEB)

    Felix, Larry [Inst. Of Gas Technology, Des Plaines, IL (United States); Farthing, William [Inst. Of Gas Technology, Des Plaines, IL (United States); Hoekman, S. Kent [Inst. Of Gas Technology, Des Plaines, IL (United States)

    2014-12-31

    This project was initiated on October 1, 2010 and utilizes equipment and research supported by the Department of Energy, National Energy Technology Laboratory, under Award Number DE- FE0005349. It is also based upon previous work supported by the Department of Energy, National Energy Technology Laboratory, under Award Numbers DOE-DE-FG36-01GOl1082, DE-FG36-02G012011 or DE-EE0000272. The overall goal of the work performed was to demonstrate and assess the economic viability of fast hydrothermal carbonization (HTC) for transforming lignocellulosic biomass into a densified, friable fuel to gasify like coal that can be easily blended with ground coal and coal fines and then be formed into robust, weather-resistant pellets and briquettes.

  18. Chemical composition of HAL, an isotopically-unusual Allende inclusion

    Science.gov (United States)

    Davis, A. M.; Tanaka, T.; Grossman, L.; Lee, T.; Wasserburg, G. J.

    1982-01-01

    Samples of hibonite, black rim, and portions of friable rim from an unusual Allende inclusion, named HAL, were analyzed by INAA and RNAA for 37 major, minor, and trace elements. An unusually low amount of Ce was found in HAL, although it otherwise was highly enriched in REE compared to C1 chondrites. HAL is also depleted in Sr, Ba, U, V, Ru, Os, and Ir relative to other refractory elements. It is concluded that the distribution of REE between hibonite and rims was established when hibonite and other refractory minerals were removed at slightly different temperatures from a hot, oxidizing gas in which they previously coexisted as separate grains. Possible locations for the chemical and mass dependent isotopic fractionation are considered to be in ejecta from the low temperature helium-burning zone of a supernova and in the locally oxidizing environment generated by evaporation of interstellar grains of near-chondritic chemical composition.

  19. Flower associations and nesting of the pollen wasp Quartinia major Kohl, 1898 (Hymenoptera, Vespidae, Masarinae in Morocco

    Directory of Open Access Journals (Sweden)

    Volker Mauss

    2018-02-01

    Full Text Available Females of Quartinia major Kohl were observed to visit flowers of Pulicaria mauritanica Batt., Cladanthus arabicus (L. Cass. and Asteriscus graveolens (Forssk. Less., (all Asteroideae Asteraceae at two localities in southern Morocco. Pollen in the provisions of two brood cells was more than 99% Aster-type (Asteroideae, indicating broad oligolecty. During pollen uptake from P. mauritanica, the females of Q. major employed a hitherto undescribed harvesting technique: They used their mouthparts to squeeze pollen from the corolla tubes of early male phase disc florets. Pollen was ingested immediately after it had been extracted. The nest was a multicellular subterranean burrow excavated in friable soil and surmounted by a turret. The nest walls were stabilized with self-generated silk.

  20. Evaluation on the Effects of Culture Medium on Regeneration of Oil Palm Plantlets from Immature Embryos (IE)

    International Nuclear Information System (INIS)

    Wan Nur Syuhada, W.S.; Rasid, O.A.; Parveez, G.K.A

    2016-01-01

    Oil palm (Elaeis guineensis) tissue culture is slow, inefficient and genotype dependent. Therefore, efforts to improve the regeneration system are essential and thereby on-going. Immature embryos (IE) have been reported to be more responsive to in vitro culture as compared to other explant types. The objective of this study is to evaluate the most efficient culture media for the regeneration of whole plants from IE. IE were cultured on three media, namely N6, MY3 and MS +Y3. Initial observation showed that calli were induced as early as two weeks after culture. They started to produce friable calli around three to four months later. IE were shown to respond differently to the tested culture media. This initial result will be useful to identify the most responsive culture media for IE as explant. (author)

  1. Recidiva en vena cava inferior de carcinoma suprarrenal

    Directory of Open Access Journals (Sweden)

    Javier Orrit

    2005-01-01

    Full Text Available Paciente de 15 meses sometido a resección de masa suprarrenal derecha. Estudio de extensión negativo e histología de tumor adrenocortical. Dos meses después presenta recidiva tumoral en vena cava inferior (VCI a nivel de venas suprahepáticas que se reseca bajo hipotermia profunda y parada circulatoria (19 min (Fig. 1. Se extrae una masa friable de 25 × 20 mm que ocluye la VCI, sin evidencia de resto tumoral, aunque se considera resección incompleta al estar infiltradas las paredes de VCI. La histología confirma carcinoma suprarrenal (Fig. 2. A los 5 meses sigue quimioterapia sin datos de nueva invasión de VCI.

  2. Areally Extensive Surface Bedrock Exposures on Mars: Many Are Clastic Rocks, Not Lavas

    Science.gov (United States)

    Rogers, A. Deanne; Warner, Nicholas H.; Golombek, Matthew P.; Head, James W.; Cowart, Justin C.

    2018-02-01

    Areally extensive exposures of intact olivine/pyroxene-enriched rock, as well as feldspar-enriched rock, are found in isolated locations throughout the Martian highlands. The petrogenetic origin(s) of these rock units are not well understood, but some previous studies favored an effusive volcanic origin partly on the basis of distinctive composition and relatively high thermal inertia. Here we show that the regolith development, crater retention, and morphological characteristics for many of these "bedrock plains" are not consistent with competent lavas and reinterpret the high thermal inertia orbital signatures to represent friable materials that are more easily kept free of comminution products through eolian activity. Candidate origins include pyroclastic rocks, impact-generated materials, or detrital sedimentary rocks. Olivine/pyroxene enrichments in bedrock plains relative to surrounding materials could have potentially formed through deflation and preferential removal of plagioclase.

  3. Embryogenic calli induced in interspecific (Elaeis guineensis x E. oleifera hybrid zygotic embryos

    Directory of Open Access Journals (Sweden)

    Paula Cristina da Silva Angelo

    2009-01-01

    Full Text Available The hybridization between oil palm (Elaeis guineensis and caiaué (E. oleifera plants is directed to obtainprogenies presenting high yields like oil palm but with reduced shoot height and resistance to lethal yellowing like caiaué.Cloning F1, BC1 and BC2 progenies can make the replication of selection trials easier. The objective of this work was to inducesomatic embryogenesis in interspecific zygotic embryos collected 100 days after pollination. Three progenies were cultivatedin an induction medium developed for Tenera (E. guineensis tp. dura x pisifera embryos. The number of embryos bearing calliand germinating was recorded and submitted to the Z test. Calli were weighted and submitted to histological analysis.Progenies differed in the number of embryos presenting plumules and calli simultaneously. By the ninth month, the apices ofincompletely developed somatic embryos were observed protruding from the surfaces of nodular calli. Highly embryogenicand friable secondary calli producing globular somatic embryos were not observed.

  4. Improving Water Repellence and Friability of Tannin-Furanic Foams by Oil-Grafted Flavonoid Tannins

    Directory of Open Access Journals (Sweden)

    Géraldine Rangel

    2016-08-01

    Full Text Available Tannin-furanic biobased foams, based on the co-reaction of bark-derived condensed tannins and thermoset furanic polymers, have low thermal conductivity, are self-extinguishing, and have high fire resistance, which allows their development for several industrial uses. One of their main drawbacks, however, is the absorption of water within the foam itself. Another problem is the rather friable surface, which is a definite drawback for some potential applications. In this work, these two problems are minimized or eliminated by introducing a component of oil-grafted tannin in the foam formulation. The incorporation of fatty chains markedly decreased foam friability and increased water repellency in the body of the foams. These properties and the compounds formed by fatty acids grafting onto the tannin flavonoids were extensively tested.

  5. Raw materials for energy generation in Canada

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, D S

    1976-03-01

    Canada is self-sufficient in energy. The energy demand in Canada up to the end of the century is predicted, and the present and future of the oil, gas, coal and uranium industries are considered. Since it is now Canadian policy to restrict export of energy sources, in the future Canada will probably make more domestic use of its coal reserves. An increase is forecast in the use of coal for electricity generation and as a feedstock for synthetic gas. A long lead time and large capital expenditure will be needed before coal can be transported from western Canada to markets in the east of the country. A relatively small amount of the coal reserves are extractable by surface mining, and new underground mining techniques will be needed to extract the extremely friable coal from the deformed seams in the mountains.

  6. Extranasopharyngeal Angiofibroma Originating in the Inferior Turbinate: A Distinct Clinical Entity at an Unusual Site

    Directory of Open Access Journals (Sweden)

    Baptista, Marco Antonio Ferraz de Barros

    2014-08-01

    Full Text Available Introduction The extranasopharyngeal angiofibroma is histologically similar to juvenile nasopharyngeal angiofibroma, differing from the latter in clinical and epidemiologic characteristics. Objectives We present a case of extranasopharyngeal angiofibroma originating in the inferior turbinate. Resumed Report The patient was a girl, 8 years and 6 months of age, who had constant bilateral nasal obstruction and recurrent epistaxis for 6 months, worse on the right side, with hyposmia and snoring. Nasal endoscopy showed a reddish lesion, smooth, friable, and nonulcerated. Computed tomography showed a lesion with soft tissue density in the right nasal cavity. We used an endoscopic approach and found the lesion inserted in the right inferior turbinate. We did a subperiosteal dissection and excision with a partial turbinectomy with a resection margin of 0.5 cm. Histopathology reported it to be an extranasopharyngeal angiofibroma. Conclusion Although rare, extranasopharyngeal angiofibroma should be considered in the diagnosis of vascular tumors of the head and neck.

  7. Extranasopharyngeal Angiofibroma Originating in the Inferior Turbinate: A Distinct Clinical Entity at an Unusual Site

    Science.gov (United States)

    Baptista, Marco Antonio Ferraz de Barros; Pinna, Fábio de Rezende; Voegels, Richard Louis

    2014-01-01

    Introduction The extranasopharyngeal angiofibroma is histologically similar to juvenile nasopharyngeal angiofibroma, differing from the latter in clinical and epidemiologic characteristics. Objectives We present a case of extranasopharyngeal angiofibroma originating in the inferior turbinate. Resumed Report The patient was a girl, 8 years and 6 months of age, who had constant bilateral nasal obstruction and recurrent epistaxis for 6 months, worse on the right side, with hyposmia and snoring. Nasal endoscopy showed a reddish lesion, smooth, friable, and nonulcerated. Computed tomography showed a lesion with soft tissue density in the right nasal cavity. We used an endoscopic approach and found the lesion inserted in the right inferior turbinate. We did a subperiosteal dissection and excision with a partial turbinectomy with a resection margin of 0.5 cm. Histopathology reported it to be an extranasopharyngeal angiofibroma. Conclusion Although rare, extranasopharyngeal angiofibroma should be considered in the diagnosis of vascular tumors of the head and neck. PMID:25992131

  8. A porous silica rock ("tripoli") in the footwall of the Jurassic Úrkút manganese deposit, Hungary: composition, and origin through carbonate dissolution

    Science.gov (United States)

    Polgari, Marta; Szabo, Zoltan; Szabo-Drubina, Magda; Hein, James R.; Yeh, Hsueh-Wen

    2005-01-01

    The mineralogical, chemical, and isotopic compositions were determined for a white tripoli from the footwall of the Jurassic Úrkút Mn-oxide ore deposit in the Bakony Mountains, Hungary. The tripoli consists of quartz and chalcedony, with SiO2 contents up to 100 wt.%; consequently, trace-element contents are very low. Oxygen isotopes and quartz crystallinity indicate a low-temperature diagenetic origin for this deposit. The tripoli was formed by dissolution of the carbonate portion of the siliceous (sponge spicules) Isztimér Limestone. Dissolution of the carbonate was promoted by inorganic and organic acids generated during diagensis and left a framework composed of diagenetic silica that preserved the original volume of the limestone layer. The relative enrichment of silica and high porosity is the result of that carbonate dissolution. The silty texture of this highly friable rock is due to the structurally weak silica framework.

  9. Primary laryngeal leishmaniasis: A rare case report

    Directory of Open Access Journals (Sweden)

    Kumar Bipin

    2009-01-01

    Full Text Available Laryngeal leishmaniasis is extremely rare. We report a case of primary laryngeal leishmaniasis in a 70-year-old male who was admitted with complaints of gradual progressive hoarseness of the voice, dyspnea, cough for the past 3 months and noisy breathing for the past 5 days. An X-ray of the soft tissue of the neck showed a prevertebral soft tissue mass causing narrowing of the airway at the C6-C7 vertebral level. A computerized tomography (CT scan showed a soft tissue mass in the subglottic region causing significant narrowing of the airway. A direct laryngoscopy showed a pinkish-white, friable mass involving the subglottic region and the anterior half of the vocal cords. With the clinical suspicion of malignancy, an endoscopic biopsy was done. A histopathological examination showed diffuse mixed inflammatory cell infiltrate in subepithelium with numerous Leishmania donovani bodies in the cytoplasm of histiocytes.

  10. The agronomic landspreading of coal bottom ash: using a regulated solid waste as a resource

    Energy Technology Data Exchange (ETDEWEB)

    Sell, N; McIntosh, T; Severance, C; Peterson, A

    1989-02-01

    Within the US, approximately 8860 Mg of dry coal bottom ash is generated daily, the majority of which is disposed of by landfilling. The disposal cost varies significantly depending on location. In Wisconsin, for example, in 1987 public landfill disposal costs ranged from 8.90 US dollars to 30 US dollars per Mg. However, bottom ash appears to be an acceptable soil amendment which may alter texture and improve tilth by making clay soils more friable and decreasing crust formation. If a generic exemption for this material can be developed with the appropriate regulatory bodies, use of coal bottom ash as a soil amendment has societal and economic advantages. This paper describes the key point of an agronomic management plant. An economic comparison indicates that, based on 1987 costs, agronomic use is only 38% as costly as landfill disposal. 14 refs., 5 tabs.

  11. Actinomycetoma of the scalp after a car accident.

    Science.gov (United States)

    Welsh, Oliverio; Morales-Toquero, Amelia; Vera-Cabrera, Lucio; Cabrera-Vera, Lucio; Vazquez-Martinez, Osvaldo; Gómez-Flores, Minerva; Ocampo-Candiani, Jorge

    2011-07-01

    Actinomycetoma is the most frequent type of mycetoma in Mexico. Localization on the scalp is very rare. Because of this topography and potential spread to the brain, the present case became a diagnostic and therapeutic challenge. We report the case of a 44-year-old woman with a 6 × 5 cm red, friable, granulomatous, vascular neoformation on the scalp and eye diagnosed as Nocardia brasiliensis actinomycetoma. A combination of amikacin and oral trimethoprim-sulfamethoxazole (SXT) was successfully administered with an excellent outcome and no side effects. This is a rare presentation of mycetoma of the scalp that was cured in 12 weeks with a combination of amikacin and SXT. © 2011 The International Society of Dermatology.

  12. High Purity Tungsten Spherical Particle Preparation From WC-Co Spent Hard Scrap

    Directory of Open Access Journals (Sweden)

    Han Chulwoong

    2015-06-01

    Full Text Available Tungsten carbide-cobalt hard metal scrap was recycled to obtain high purity spherical tungsten powder by a combined hydrometallurgy and physical metallurgy pathway. Selective leaching of tungsten element from hard metal scrap occurs at solid / liquid interface and therefore enlargement of effective surface area is advantageous. Linear oxidation behavior of Tungsten carbide-cobalt and the oxidized scrap is friable to be pulverized by milling process. In this regard, isothermally oxidized Tungsten carbide-cobalt hard metal scrap was mechanically broken into particles and then tungsten trioxide particle was recovered by hydrometallurgical method. Recovered tungsten trioxide was reduced to tungsten particle in a hydrogen environment. After that, tungsten particle was melted and solidified to make a spherical one by RF (Ratio Frequency thermal plasma process. Well spherical tungsten micro-particle was successfully obtained from spent scrap. In addition to the morphological change, thermal plasma process showed an advantage for the purification of feedstock particle.

  13. Metastatic mammary carcinoma in a cow

    Directory of Open Access Journals (Sweden)

    Manoela Marchezan Piva

    Full Text Available ABSTRACT: Mammary gland neoplasms in cattle are rarely observed in the field veterinary diagnostics routine. Therefore, the objective of this study is to report a metastatic mammary carcinoma in a fourteen-year-old Holstein cow in the state of Santa Catarina, Brazil. The animal was diagnosed by the field veterinarian with clinical mastitis that was unresponsive to treatment, and was euthanized due to the poor prognosis. At the necropsy, multiple yellow, firm, and sometimes friable nodules, ranging from 0.1 to 20cm were observed in all mammary glands, lymph nodes, kidneys, spleen, liver, pancreas, mediastinal lymph nodes, heart, and lungs. The final diagnosis of mammary carcinoma was established through the association of clinical, necropsy, histopathological, and immunohistochemical findings. Differential diagnoses included diseases such as bovine tuberculosis and chronic fungal or bacterial mastitis.

  14. Hepatic lipidosis associated with cobalt deficiency in Omani goats.

    Science.gov (United States)

    Johnson, E H; Muirhead, D E; Annamalai, K; King, G J; Al-Busaidy, R; Hameed, M S

    1999-06-01

    Livers from 36 of 684 (5.3%) apparently healthy goats examined at an abattoir in the greater Muscat area of Oman exhibited gross pathological findings characterized by extremely pale, friable, fatty livers encompassing the entire organ. Histopathologically, diffuse hepatic lipidosis and occasional bile duct proliferation were observed. Periodic acid Schiff-positive, diastase-resistant pigment was observed in the macrophages lining the sinusoids. These histopathological lesions were consistent with those characteristic of ovine white liver disease. Cobalt analysis revealed that normal livers had six times more cobalt and a 3-fold less fat content than those measured in the fatty livers. This is the first report of an association between cobalt deficiency and hepatic lipidosis in Omani goats.

  15. Importance of well logging measurements in the design of underground railway tunnels

    International Nuclear Information System (INIS)

    Kiss, E.Z.; Szlaboczky, P.

    1981-01-01

    The paper shows how logs can be used in the construction of underground railway tunnels in terciary sediments. Even standard well logging techniques (electric conductivity, gamma logging) can provide important additional information on the wells if conclusions concerning construction technology are gained from the logs. In the course of continuous research work the application of well logs renders an essential help if the measurements give in-situ information on absolute values of the well sections by revealing the various geological formations based on the distribution of characteristic parameters. Well logging increases the resolving power of the mechanical method of layer differentiation. Beside the usual geological interpretation of logs the zones of shifting rocks, hard and friable formations as well as intercalations leading to problems in construction technology can be pointed out. (author)

  16. Esophagojejunal Anastomosis Fistula, Distal Esophageal Stenosis, and Metalic Stent Migration after Total Gastrectomy

    Directory of Open Access Journals (Sweden)

    Nadim Al Hajjar

    2015-01-01

    Full Text Available Esophagojejunal anastomosis fistula is the main complication after a total gastrectomy. To avoid a complex procedure on friable inflamed perianastomotic tissues, a coated self-expandable stent is mounted at the site of the anastomotic leak. A complication of stenting procedure is that it might lead to distal esophageal stenosis. However, another frequently encountered complication of stenting is stent migration, which is treated nonsurgically. When the migrated stent creates life threatening complications, surgical removal is indicated. We present a case of a 67-year-old male patient who was treated at our facility for a gastric adenocarcinoma which developed, postoperatively, an esophagojejunostomy fistula, a distal esophageal stenosis, and a metallic coated self-expandable stent migration. To our knowledge, this is the first reported case of an esophagojejunostomy fistula combined with a distal esophageal stenosis as well as with a metallic coated self-expandable stent migration.

  17. Fuzzy logic application for data correction of gamma ray profile and correlation with effective porosity of core from Resende Basin, Rio de Janeiro; Aplicacao da logica fuzzy para correcao de dados de perfil de raios gama e correlacao com porosidade efetiva de testemunhos da Bacia de Resende, Rio de Janeiro

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Francisco de Assis Leal de; Tunala, Leonardo Fernandes; Abreu, Carlos Jorge de; Lopes, Ricardo Tadeu, E-mail: pachoteki@yahoo.com.br, E-mail: leotunala@hotmail.com, E-mail: abreu@geologia.ufrj.br, E-mail: ricardo@lin.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ/CCMN), RJ (Brazil). Centro de Ciencias Matematicas e da Natureza. Inst. de Geociencias. Dept. de Geologia; Rocha, Paula Lucia Ferrucio da, E-mail: ferrucio@acd.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil); Martins, Ricardo Rhomberg, E-mail: ricardo301@gmail.com [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola Politenica de Engenharia; Lima, Inaya Correa Barbosa, E-mail: inaya@lin.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Centro de Tecnologia

    2010-12-15

    This work presents here a study on the porosity of cores from Resende Basin (Rio de Janeiro). The first step involved the selection, thinning of the material (core) and sample preparation for the use of porosimeter to obtain effective porosity. The material studied is sandstone, friable, coarse to very fine of three wells (GPR1, GPR2 and GPR3). The fuzzy logic (MatLab) was applied to the effective porosity data calculated from the gamma ray (GR) profile for the construction of a synthetic profile and from this we could identify the errors made in calculating the data. Then the results of porosity from the core were correlated with data from the corrected effective porosity (gamma ray profile) in order to prove the results obtained with both methods. The analysis of the synthetic porosity calculated by the fuzzy logic has shown that this is a promising method for assessing the quality of data and to obtain good fits. (author)

  18. Iris metastasis of gastric adenocarcinoma.

    Science.gov (United States)

    Celebi, Ali Riza Cenk; Kilavuzoglu, Ayse Ebru; Altiparmak, U Emrah; Cosar, C Banu; Ozkiris, Abdullah

    2016-03-08

    Iris metastasis in patients with gastric cancer is extremely rare. Herein, it is aimed to report on a patient with gastric adenocarcinoma and iris metastasis. A 65-year-old patient with the history of gastric cancer was admitted for eye pain and eye redness on his left eye. There was ciliary injection, severe +4 cells with hypopyon in the anterior chamber and a solitary, friable, yellow-white, fleshy-creamy vascularized 2 mm × 4 mm mass on the upper nasal part of the iris within the left eye. The presented patient's mass lesion in the iris fulfilled the criteria of the metastatic iris lesion's appearance. The ocular metastasis occurred during chemotherapy. Iris metastasis can masquerade as iridocyclitis with pseudohypopyon or glaucoma. In patients with a history of gastric cancer that present with an iris mass, uveitis, and high intraocular pressure, ocular metastasis of gastric cancer should be a consideration.

  19. Ash and heavy metals in fluidized bed-combustion; Tuhka ja raskasmetallit puuperaeisen jaetteen kerrosleijupoltossa

    Energy Technology Data Exchange (ETDEWEB)

    Kaessi, T.; Aittoniemi, P. [IVO International, Vantaa (Finland)

    1996-12-01

    Combustion ashes and submicron fly ash particles were characterized in two industrial boilers (bubbling vs. circulating fluidized bed) burning paper mill deinking sludge and bark or wood as support fuel. Bulk samples from fly ash, circulating ash and bottom ash were analyzed. Fine particles in fly ash were monitored and sampled for microscopic studies. The mass size distribution of fly ash was measured and the chemical composition according to particle size was analyzed. The results showed that ash consists of large and friable clusters formed by sintering of small mineral particles originating from paper fillers. Very few ash particles were fused and they were found only among the smallest particles. No agglomerates of fused particles were found. If the residence time in furnace is long enough sintering may proceed further and ash structure grows more dense. No indication of ash vaporization was detected. These results were similar for bubbling and circulating fluidized bed boilers. (author)

  20. La estimación de recursos niquelíferos con corrección geofísico-geoestadística

    Directory of Open Access Journals (Sweden)

    Jorge Acosta-Breal

    2007-03-01

    Full Text Available Se presenta un procedimiento para corregir los datos de pozos de perforación, en lo referido al espesor de mena y de friable, a través de un coeficiente de corrección (KG que incorpora toda la información geológica-geofísica disponible al respecto, con el objetivo de obtener una estimación de recursos más cercana a la real. Los datos geofísicos, provenientes de los métodos de Sondeo Eléctrico Vertical o de Georradar se integran a los de perforación mediante la Geoestadística. Para ejemplificar se tomaron datos del yacimiento Camarioca Este.

  1. Primary oral and nasal transmissible venereal tumor in a mix-breed dog

    Directory of Open Access Journals (Sweden)

    Mahdieh Rezaei

    2016-05-01

    Full Text Available Transmissible venereal tumor (TVT is a coitally transmitted tumor of dogs with widespread distribution. The present study describes the occurrence of the primary oral and nasal TVT in a 10-year-old, female, mix-breed dog. The case was presented with a history of anorexia, inability to swallow and dyspnea. Clinical examinations revealed the emaciation, muzzle deformity due to the presence of a friable, fleshy, cauliflower-like mass in the oral cavity and submandibular lymphadenopathy. TVT was diagnosed based on histopathological findings. The dog was discharged with therapeutic intervention with vincristine. Unfortunately, the case died before readmission because of the progressive worsening of the general condition. Our findings highlight the need for considering TVT for the differential diagnosis of the extragenital masses in dogs.

  2. Soil friability

    DEFF Research Database (Denmark)

    Munkholm, Lars Juhl

    2011-01-01

    This review gathers and synthesizes literature on soil friability produced during the last three decades. Soil friability is of vital importance for crop production and the impact of crop production on the environment. A friable soil is characterized by an ease of fragmentation of undesirably large...... aggregates/clods and a difficulty in fragmentation of minor aggregates into undesirable small elements. Soil friability has been assessed using qualitative field methods as well as quantitative field and laboratory methods at different scales of observation. The qualitative field methods are broadly used...... by scientists, advisors and farmers, whereas the quantitative laboratory methods demand specialized skills and more or less sophisticated equipment. Most methods address only one aspect of soil friability, i.e. either the strength of unconfined soil or the fragment size distribution after applying a stress. All...

  3. Biology and management of palm dynastid beetles: recent advances.

    Science.gov (United States)

    Bedford, Geoffrey O

    2013-01-01

    Coconut, oil, and date palms are important crops in the tropics and are attacked by dynastids that cause loss of production or death of hosts. Knowledge of their breeding sites has been extended since a previous review in 1980. The fungus Metarhizium anisopliae has potential as a biopesticide against immature stages in friable breeding sites. The molecular biology and ultrastructure of Oryctes rhinoceros Nudivirus (OrNV), disseminated by adults, have been studied, and this pathogen can reduce O. rhinoceros populations and damage when introduced into new locations, especially where damage had been high. New PCR techniques may enable reliable quantification of dosages ingested and hence virulence of different isolates. Male-produced aggregation pheromones have been identified in several species, for which they may have management potential, having been used commercially for trapping O. rhinoceros in oil palm plantations in Southeast Asia, and tested against O. monoceros in Africa.

  4. Hepatic neosporosis in a dog treated for pemphigus foliaceus.

    Science.gov (United States)

    Hoon-Hanks, Laura L; Regan, Daniel; Dubey, Jitender P; Carol Porter, Merry; Duncan, Colleen G

    2013-11-01

    A 4-year-old, female, spayed Border Collie dog was presented for progressive lethargy, inappetence, and weakness of 4 days duration. The animal had been diagnosed with pemphigus foliaceus 3 months prior and was receiving combination immunosuppressive therapy. Serum biochemistry revealed severely elevated liver enzymes and bilirubin, and humane euthanasia was elected. Gross postmortem examination revealed a diffusely pale tan to slightly yellow, enlarged, markedly friable liver with an enhanced reticular pattern. Histologically, the hepatic changes consisted of multifocal to coalescing areas of severe vacuolar degeneration, numerous coalescing foci of hepatocellular necrosis, and myriad intra- and extracellular protozoa that reacted immunohistochemically with polyclonal antibodies to Neospora caninum, and not Toxoplasma gondii. Neosporosis in the current case is thought to be due to reactivation of latent N. caninum occurring with the administration of glucocorticoid therapy. The severe complication in the present case highlights the importance of early detection and mitigation of common infections in immunosuppressed animals.

  5. Competing styles of deep-marine explosive eruptions revealed from Axial seamount and Juan De Fuca ridge push core records

    Science.gov (United States)

    Portner, R. A.; Clague, D. A.; Paduan, J. B.; Martin, J. F.

    2012-12-01

    Pyroclastic lithofacies from Axial seamount record two distinct styles of deep-marine explosive eruption activity at 1.4-1.5 km water depth. The first style is preserved by limu o Pele-rich ash, which is widely distributed and thin bedded. Individual beds are normal to coarse-tail graded with increasing planar grain-fabric and decreasing limu o Pele thickness upward. Grain-size generally ranges from medium lapilli to medium ash, which is well to poorly sorted depending on the abundance of outsized fluidal shards. Fluidal shards include limu o Pele and Pele's hair, and lesser amounts of tendril-like tube pumice and droplet-like shards. Rare blocky to fluidal lapilli contain up to 70% vesicles. Angular plagioclase and basalt lithics occur in minor amounts (2-15%). Most beds display overall upward changes in particle morphology from dense blocky angular lapilli in their bases to fluidal ash in their tops. Shards are most equidimensional near the base, and most varied in the mid-upper parts of most beds where 4-8 mm size limu occur with 1-2 mm blocky shards. This outsized-component association results from drastically different settling speeds for the two morphologies. Outsized fluidal shards become abundant across a relatively sharp boundary in the middle to lower portions of most beds causing a seemingly double-graded appearance. These systematic changes in particle morphology and grain size suggest a cogenetic association of blocky and fluidal shards to the same depositional event and causative eruption. Fluidal-vesicular particle morphologies suggest that this lithofacies represents ash fall from magmatically explosive eruptions. Planar-grain fabric trends, absence of shard imbrication, and grading profiles suggest that beds were deposited via near-vertical suspension fall-out from weak turbidity flows. The second pyroclastic lithofacies is dominated by normal graded greenish grey ashy mud beds. Ash makes up 10-80% of individual beds, and is well-sorted, coarse- to

  6. The effect of particle shape on hopper discharge

    Energy Technology Data Exchange (ETDEWEB)

    Cleary, P.W. [CSIRO, Clayton, Vic. (Australia). Mathematical and Information Sciences

    1999-07-01

    Hopper flows are an important class of industrial particle flows. The inclusion of particle shape allows DEM models to replicate many features of real hopper flows that are not possible when using circular particles. Elongated particles can produce flow rates up to 30% lower than for circular particles and the flow patterns are quite different. The yielding of the particle microstructure resembles more the tearing of a continuum solid, with large scale quasi-stable voids being formed and large groups of particles moving together. The flow becomes increasingly concentrated in a relatively narrow funnel above the hopper opening. This is encouragement that DEM may be able to predict important problems such as bridging and rat-holing. Increasing the blockiness or angularity of the particles also increases resistance to flow and reduces flow rates by up to 28% but does not have any perceptible effect on the nature of the flow. 11 refs., 7 figs.

  7. Lathlike upper bainite in a silicon steel

    International Nuclear Information System (INIS)

    Liu Cheng; Zhao Zhenbo; Bhole, S.D.

    2006-01-01

    The morphology and mechanical properties of upper bainite formed isothermally at 400 deg. C for different holding times in a 1.83 wt.% silicon steel have been investigated by optical metallograph, X-ray diffraction and transmission electron microscopy (TEM). In the early stage of upper bainitic transformation, lathlike bainite whose individual lath ferrite is separated by the thin film type of retained austenite is obtained. As the isothermal holding times are increased, the blocky region consisting of retained austenite and martensite is also found. The stability of retained austenite in lathlike upper bainite is studied in relation to the isothermal treatment times, and the heat treatment conditions. The results show that an optimum combination of strength and ductility is attributed to the formation of bainitic ferrite (BF) and a large amount of thin film carbon-enriched retained austenite in the upper bainite

  8. Effect of Austenitising Temperature on Mechanical Properties of Nanostructured Bainitic Steel

    Directory of Open Access Journals (Sweden)

    Jing Zhao

    2017-07-01

    Full Text Available Nanostructured bainite was obtained in high-carbon Si-Al-rich steel by low-temperature (220–260 °C isothermal transformation after austenitisation at different temperatures (900 °C, 1000 °C, and 1150 °C. Improved strength-ductility-toughness balance was achieved in the nanostructured bainitic steel austenitised at low temperatures (900 °C and 1000 °C. Increasing the austenitising temperature not only coarsened prior austenite grains and bainite packets, but also increased the size and fraction of blocky retained austenite. High austenitising temperature (1150 °C remarkably decreased ductility and impact toughness, but had a small effect on strength and hardness.

  9. On structure-property relationship in nanostructured bainitic steel subjected to the quenching and partitioning process

    Energy Technology Data Exchange (ETDEWEB)

    Luo, Ping [Material Science & Engineering Research Center, School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044 (China); Gao, Guhui, E-mail: gaogh@bjtu.edu.cn [Material Science & Engineering Research Center, School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044 (China); Zhang, Han [Max-Planck-Institut für Eisenforschung, Max-Planck-Str. 1, 40237 Düsseldorf (Germany); Tan, Zhunli [Material Science & Engineering Research Center, School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044 (China); Misra, R.DK. [Laboratory for Excellence in Advanced Steel Research, Department of Metallurgical, Materials and Biomedical Engineering, University of Texas at El Paso, TX 79968-0520 (United States); Bai, Bingzhe [Material Science & Engineering Research Center, School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044 (China); Tsinghua University, Key Laboratory of Advanced Material, School of Material Science and Engineering, Beijing 100084 (China)

    2016-04-20

    We elucidate here the mechanistic contribution of the application of quenching and partitioning (Q&P) concept to a high carbon Mn-Si-Cr steel in obtaining a multiphase microstructure comprising of martensite/austenite and nanostructured bainite (bainitic ferrite and nanometer-sized film-like retained austenite) that exhibited tensile strength of 1923 MPa and total elongation of 18.3%. The excellent mechanical properties are attributed to the enhanced refinement of blocky austenite islands obtained by the Q&P process. The austenite was stabilized by both carbon partitioning from martensite and bainite transformation. Compared with conventional heat treatment to produce nanostructured bainite, the total time is significantly reduced without degradation of mechanical properties.

  10. In-situ SEM observation on fracture behavior of austempered silicon alloyed steel

    Directory of Open Access Journals (Sweden)

    Chen Xiang

    2009-08-01

    Full Text Available Crack initiation, propagation and microfracture processes of austempered high silicon cast steel have been investigated by using an in-situ tensile stage installed inside a scanning electron microscope chamber. It is revealed that micro cracks always nucleate at the yielding near imperfections and the boundary of matrix-inclusions due to the stress concentration. There are four types of crack propagations in the matrix: crack propagates along the boundary of two clusters of bainitic ferrite; crack propagates along the boundary of ferrite朼ustenite in bainitic ferrite laths; crack propagates into bainitic ferrite laths; crack nucleates and propagates in the high carbon brittle plate shape martensite which is transformed from some blocky retained austenite due to plastic deformation. Based on the observation and analysis of microfracture processes, a schematic diagram of the crack nucleation and propagation process of high silicon cast steel is proposed

  11. Morphological stability of Sm123 superconductor during peritectic solidification from Sm211 + L mixture

    International Nuclear Information System (INIS)

    Sumida, Masaki; Shiohara, Yuh; Umeda, Takateru

    2000-01-01

    The interface stability of the Sm 123 superconductor was analyzed in accordance with the constitutional undercooling criterion. As the single-crystal growth of the 123 phase is largely dependent on the growth-interface stability, a quantitative analysis was very much required. From this analysis, it was clarified that the constitutional undercooling must exist in the liquid when the 123 growth interface comes close to a 211 particle during the peritectic solidification. It was also predicted that the larger 211 particle radius, smaller volume fraction of the 211 particles, larger growth rate, or smaller imposed temperature gradient would cause easy occurrence of the constitutional undercooling ahead of the 123 growth interface. Taking into account the nucleation at the L/211 interface just ahead of the 123 growth front due to the constitutional undercooling, the transition of 123 growth from a planar-interface morphology to an equiaxed blocky morphology was investigated quantitatively and qualitatively

  12. Integration of airborne Thematic Mapper Simulator (TMS) data and digitized aerial photography via an ISH transformation. [Intensity Saturation Hue

    Science.gov (United States)

    Ambrosia, Vincent G.; Myers, Jeffrey S.; Ekstrand, Robert E.; Fitzgerald, Michael T.

    1991-01-01

    A simple method for enhancing the spatial and spectral resolution of disparate data sets is presented. Two data sets, digitized aerial photography at a nominal spatial resolution 3,7 meters and TMS digital data at 24.6 meters, were coregistered through a bilinear interpolation to solve the problem of blocky pixel groups resulting from rectification expansion. The two data sets were then subjected to intensity-saturation-hue (ISH) transformations in order to 'blend' the high-spatial-resolution (3.7 m) digitized RC-10 photography with the high spectral (12-bands) and lower spatial (24.6 m) resolution TMS digital data. The resultant merged products make it possible to perform large-scale mapping, ease photointerpretation, and can be derived for any of the 12 available TMS spectral bands.

  13. Effect of rare earth and titanium additions on the microstructures and properties of low carbon Fe-B cast steel

    International Nuclear Information System (INIS)

    Fu Hanguang; Xiao Qiang; Kuang Jiacai; Jiang Zhiqiang; Xing Jiandong

    2007-01-01

    A new type of wear resistant low carbon Fe-B cast steel with granular borides can be obtained by alloying with titanium and cerium rare earth (RE). As a result, the as-cast eutectic boride structures of Fe-B cast steel are greatly refined and a blocky, less interconnected boride network is obtained from continuous ledeburite. After heat treatment, the boride eutectic in the modified Fe-B cast steel is in the form of a granular boride structure that appears to be isolated particles The guide rollers made of modified low carbon Fe-B cast steel show excellent wear resistance and thermal fatigue resistance in high speed wire mills

  14. Surfactant assisted synthesis of lamellar nanostructured LiFePO4 at 388 K

    International Nuclear Information System (INIS)

    Liu Chao; Ma Dongxia; Ji Xiujie; Zhao Shanshan; Li Song

    2011-01-01

    Lamellar nanostructured lithium iron phosphate (Lα-LFP) was synthesized using anion surfactant sodium dodecyl sulphonate (SDS) as supermolecular template in water-ethanol media at 388 K under self-generated pressure. FeSO 4 , (NH 4 ) 2 HPO 4 and LiOH were used as Fe, P and Li sources, respectively. The inorganic phase was analyzed by X-ray diffraction (XRD). The morphology and the lamellar nanostructure were observed by field emitting scanning electron microscopy (FESEM). The results showed that the synthesized Lα-LFP presents not only the ordered lamellar microstructure accumulated by 20-40-nm thick LFP layers, but also the consequent self-assembled blocky particles of 0.5-1 μm. In contrast, template free LFP (TF-LFP) show a flake-shaped and mess-orientated microstructure. As a soft template, SDS played the roles of inducing the lamellar nanostructure, purifying the inorganic phase and decreasing the synthesis temperature.

  15. A united refinement technology for commercial pure Al by Al-10Ti and Al-Ti-C master alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ma Xiaoguang [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Liu Xiangfa [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China)], E-mail: xfliu@sdu.edu.cn; Ding Haimin [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China)

    2009-03-05

    Because flake-like TiAl{sub 3} particles in Al-Ti-C master alloys prepared in a melt reaction method dissolve slowly when they are added into Al melt at 720 deg. C, Ti atoms cannot be released rapidly to play the assistant role of grain refinement, leading to a poor refinement efficiency of Al-Ti-C master alloys. A united refinement technology by Al-10Ti and Al-Ti-C master alloys was put forward in this paper. The rational combination of fine blocky TiAl{sub 3} particles in Al-10Ti and TiC particles in Al-Ti-C can improve the nucleation rate of {alpha}-Al. It not only improves the grain refinement efficiency of Al-Ti-C master alloys, but also reduces the consumption.

  16. Crystallography and Morphology of MC Carbides in Niobium-Titanium Modified As-Cast HP Alloys

    Science.gov (United States)

    Buchanan, Karl G.; Kral, Milo V.; Bishop, Catherine M.

    2014-07-01

    The microstructures of two as-cast heats of HP alloy stainless steels modified with niobium and titanium were examined with particular attention paid to the interdendritic niobium-titanium-rich carbides formed during solidification of these alloys. Generally, these precipitates obtain a blocky morphology in the as-cast condition. However, the (NbTi)C precipitates may obtain a nodular morphology. To provide further insight to the origin of the two different morphologies obtained by the (NbTi)C precipitates in the HP-NbTi alloy, the microstructure and crystallography of each have been studied in detail using scanning electron microscopy, transmission electron microscopy, various electron diffraction methods (EBSD, SAD, and CBED), and energy-dispersive X-ray spectroscopy.

  17. The ATLAS Experiment Laboratory - Overview

    International Nuclear Information System (INIS)

    Malecki, P.

    1999-01-01

    Full text: ATLAS Experiment Laboratory has been created by physicists and engineers preparing a research programme and detector for the LHC collider. This group is greatly supported by members of other Departments taking also part (often full time) in the ATLAS project. These are: J. Blocki, J. Godlewski, Z. Hajduk, P. Kapusta, B. Kisielewski, W. Ostrowicz, E. Richter-Was, and M. Turala. Our ATLAS Laboratory realizes its programme in very close collaboration with the Faculty of Physics and Nuclear Technology of the University of Mining and Metallurgy. ATLAS, A Toroidal LHC ApparatuS Collaboration groups about 1700 experimentalists from about 150 research institutes. This apparatus, a huge system of many detectors, which are technologically very advanced, is going to be ready by 2005. With the start of the 2 x 7 TeV LHC collider ATLAS and CMS (the sister experiment at LHC) will begin their fascinating research programme at beam energies and intensities which have never been exploited. (author)

  18. Geometric morphometric analysis of cyclical body shape changes in color pattern variants of Cichla temensis Humboldt, 1821 (Perciformes: Cichlidae demonstrates reproductive energy allocation

    Directory of Open Access Journals (Sweden)

    Paul Reiss

    Full Text Available Previously recognized color and pattern variants of adult Cichla temensis in Amazon flood pulse river environments reflect the cycling of individuals through seasonal sexual maturity and spawning. Individuals also vary in shape from blocky to fusiform. To determine if shape differences are related to patterns of fat reserve deposition and utilization, and to quantify the relationship of shape with color and pattern variation and life history status, specimens in each of four previously defined grades of color and pattern variation were compared using geometric morphometric techniques. Progressive shape changes occurred between grades independent of sex and correlated to gonosomatic index (GSI. Thin plate spline deformation visualizations indicate that the observed shape differences are related to fat deposition patterns. The seasonal timing of shape change and its link to color pattern variation, sexual maturity and local water level conditions suggests a relationship between the physiological and behavioral characteristics of C. temensis and the cyclical flood pulse pattern of its habitat.

  19. Evaluation of multichannel Wiener filters applied to fine resolution passive microwave images of first-year sea ice

    Science.gov (United States)

    Full, William E.; Eppler, Duane T.

    1993-01-01

    The effectivity of multichannel Wiener filters to improve images obtained with passive microwave systems was investigated by applying Wiener filters to passive microwave images of first-year sea ice. Four major parameters which define the filter were varied: the lag or pixel offset between the original and the desired scenes, filter length, the number of lines in the filter, and the weight applied to the empirical correlation functions. The effect of each variable on the image quality was assessed by visually comparing the results. It was found that the application of multichannel Wiener theory to passive microwave images of first-year sea ice resulted in visually sharper images with enhanced textural features and less high-frequency noise. However, Wiener filters induced a slight blocky grain to the image and could produce a type of ringing along scan lines traversing sharp intensity contrasts.

  20. Sharp spatially constrained inversion

    DEFF Research Database (Denmark)

    Vignoli, Giulio G.; Fiandaca, Gianluca G.; Christiansen, Anders Vest C A.V.C.

    2013-01-01

    We present sharp reconstruction of multi-layer models using a spatially constrained inversion with minimum gradient support regularization. In particular, its application to airborne electromagnetic data is discussed. Airborne surveys produce extremely large datasets, traditionally inverted...... by using smoothly varying 1D models. Smoothness is a result of the regularization constraints applied to address the inversion ill-posedness. The standard Occam-type regularized multi-layer inversion produces results where boundaries between layers are smeared. The sharp regularization overcomes...... inversions are compared against classical smooth results and available boreholes. With the focusing approach, the obtained blocky results agree with the underlying geology and allow for easier interpretation by the end-user....

  1. Synthesis mechanism of an Al-Ti-C grain refiner master alloy prepared by a new method

    Science.gov (United States)

    Zhang, B. Q.; Lu, L.; Lai, M. O.; Fang, H. S.; Ma, H. T.; Li, J. G.

    2003-08-01

    The mechanisms of in-situ synthesis of an Al-Ti-C grain-refiner master alloy, prepared by adding a powder mixture of potassium titanium fluoride and carbon into an aluminum melt, have been systematically studied. It was found that vigorous reactions occurred at the initial stage of reaction and then slowed down. After about 20 minutes, the reactions, which led the formation of blocky titanium aluminides and submicron titanium carbides in the aluminum matrix, appeared to reach completion. Potassium titanium fluoride reacted with aluminum and carbon at 724 °C and 736 °C, respectively, resulting in the formation of titanium aluminides and titanium carbides in the aluminum matrix as well as in the formation of a low-melting-point slag of binary potassium aluminofluorides. The reaction between potassium titanium fluoride and carbon is believed to be the predominant mechanism in the synthesis of TiC by this method.

  2. Evolution of Iron-containing Compounds in Al-Cu Alloys during Heat Treatment

    Directory of Open Access Journals (Sweden)

    Liu Kun

    2016-01-01

    Full Text Available The evolution of iron-containing compounds in Al-Cu 206 cast alloy during solution treatment has been investigated. Results show that platelet β-Fe and Chinese script α-Fe are the two iron-containing compounds in as-cast condition. Little change is observed on β-Fe during solution treatment. However, fine blocky post β-Fe begins to form on α-Fe when solution treated at 520°C for 8hrs. When soaking time is extended to 24 hrs, α–Fe is found to decompose to fine branches while post β-Fe present as clusters on these branches. Al-Cu-Mg-Si Q phase is observed to form at the edge of decomposed α-Fe, possibly the result of Si from decomposed α-Fe.

  3. A novel no-reference objective stereoscopic video quality assessment method based on visual saliency analysis

    Science.gov (United States)

    Yang, Xinyan; Zhao, Wei; Ye, Long; Zhang, Qin

    2017-07-01

    This paper proposes a no-reference objective stereoscopic video quality assessment method with the motivation that making the effect of objective experiments close to that of subjective way. We believe that the image regions with different visual salient degree should not have the same weights when designing an assessment metric. Therefore, we firstly use GBVS algorithm to each frame pairs and separate both the left and right viewing images into the regions with strong, general and week saliency. Besides, local feature information like blockiness, zero-crossing and depth are extracted and combined with a mathematical model to calculate a quality assessment score. Regions with different salient degree are assigned with different weights in the mathematical model. Experiment results demonstrate the superiority of our method compared with the existed state-of-the-art no-reference objective Stereoscopic video quality assessment methods.

  4. Effect of Ferrite Morphology on Sensitization of 316L Austenitic Stainless Steels

    Energy Technology Data Exchange (ETDEWEB)

    Jang, Hun; Lee, Jun Ho; Jang, Changheui [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

    2013-05-15

    The sensitization behaviors of L-grade SSs having predominant austenitic structure with small amount of ferrite have not been well understood. In this regard, the effect of ferrite morphology on sensitization was investigated in this study. The sensitization behaviors of three heats of 316L and 316LN SSs were investigated, Stringer type of ferrite (316L - heat A and B) showed the early sensitization by chromium depletion at ferrite. austenite interface. And, later sensitization is due to GB sensitization. On the other hand, blocky type of ferrite (316L - heat C) showed lower DOS and higher resistance to GB sensitization. It could be due to sufficient supply of chromium from relatively large ferrite phase. As a consequence, the sensitization of 316L SSs could be affected by their ferrite morphology rather than ferrite content. The sensitized region was distinguishable from results of DL-EPR tests. It can be used as an effective method for evaluation of type of sensitization.

  5. A united refinement technology for commercial pure Al by Al-10Ti and Al-Ti-C master alloys

    International Nuclear Information System (INIS)

    Ma Xiaoguang; Liu Xiangfa; Ding Haimin

    2009-01-01

    Because flake-like TiAl 3 particles in Al-Ti-C master alloys prepared in a melt reaction method dissolve slowly when they are added into Al melt at 720 deg. C, Ti atoms cannot be released rapidly to play the assistant role of grain refinement, leading to a poor refinement efficiency of Al-Ti-C master alloys. A united refinement technology by Al-10Ti and Al-Ti-C master alloys was put forward in this paper. The rational combination of fine blocky TiAl 3 particles in Al-10Ti and TiC particles in Al-Ti-C can improve the nucleation rate of α-Al. It not only improves the grain refinement efficiency of Al-Ti-C master alloys, but also reduces the consumption

  6. Wind-Eroded Crater Floors and Intercrater Plains, Terra Sabaea, Mars

    Science.gov (United States)

    Irwin, Rossman P.; Wray, James J.; Mest, Scott C.; Maxwell, Ted A.

    2018-02-01

    Ancient impact craters with wind-eroded layering on their floors provide a record of resurfacing materials and processes on early Mars. In a 54 km Noachian crater in Terra Sabaea (20.2°S, 42.6°E), eolian deflation of a friable, dark-toned layer up to tens of meters thick has exposed more resistant, underlying light-toned material. These layers differ significantly from strata of similar tone described in other regions of Mars. The light-toned material has no apparent internal stratification, and visible/near-infrared spectral analysis suggests that it is rich in feldspar. Its origin is ambiguous, as we cannot confidently reject igneous, pyroclastic, or clastic alternatives. The overlying dark-toned layer is probably a basaltic siltstone or sandstone that was emplaced mostly by wind, although its weak cementation and inverted fluvial paleochannels indicate some modification by water. Negative-relief channels are not found on the crater floor, and fluvial erosion is otherwise weakly expressed in the study area. Small impacts onto this crater's floor have exposed deeper friable materials that appear to contain goethite. Bedrock outcrops on the crater walls are phyllosilicate bearing. The intercrater plains contain remnants of a post-Noachian thin, widespread, likely eolian mantle with an indurated surface. Plains near Hellas-concentric escarpments to the north are more consistent with volcanic resurfacing. A 48 km crater nearby contains similar dark-over-light outcrops but no paleochannels. Our findings indicate that dark-over-light stratigraphy has diverse origins across Mars and that some dark-toned plains with mafic mineralogy are not of igneous origin.

  7. The Effect of Plant Growth Regulators and Different Explants on the Response of Tissue Culture and Cell Suspension Cultures of German Chamomile (Matricaria chamomilla L.

    Directory of Open Access Journals (Sweden)

    L. Koohi,

    2014-07-01

    Full Text Available German chamomile (Matricaria chamomilla L. is one of the most important medicinal plants that its essential oils used in different medicinal industries. In this study which was carried out in 2013 growing season at the Faculty of Agricultural Sciences of the University of Mohaghegh Ardabili, the in vitro response of leaf and hypocotyl explants of German Chamomile in B5 medium supplemented with different levels of plant growth regulators including 2,4-D, naphthalene acetic acid (NAA, kinetin and 6-benzylaminopurine (BAP were investigated in a factorial experiment based on completely randomized design (CRD.In addition, cell suspension cultures were established and characterized. Hypocotyl and leaf explants exhibited cell proliferation and produced callus within 1-2 weeks. The highest fresh weight of the callus (264.1 mg was produced by leaf explants in the medium supplemented with 0.5 mg/l 2,4-D and 1 mg/l BAP. However, the leaf explants cultured on medium containing 1.5 mg/l 2,4-D showed the lowest cell proliferation and callus yield (40.42 mg. The highest percentage of root induction from leaf explants (58.73% was observed on the medium containing 4 mg/l 2,4-D and 1 mg/l Kin, and from hypocotyl explants (48.61% was observed on medium supplemented with 1.5 mg/l NAA. The 42.22% of calli derived from hypocotyl explants on B5 medium supplemented with 4 mg/l NAA and 3 mg/l BAP, were friable. Cell suspension cultures of German chamomile were established by transferring of hypocotyl-derived friable calli into the MS medium supplemented with 1.5 mg/l 2,4-D and 1 mg/l kinetin. The growth curve of cell proliferations started 4 days after culture and continued to grow until day 13th, where the cells entered stationary phase.

  8. Zeatin and Thidiazuron Induced Embryogenic Calli From In Vitro Leaf and Stem of Jojoba (Simmondsia chinensis).

    Science.gov (United States)

    El-Ashry, Amal Abd El-Latif; Gabr, Ahmed Mohamed Magdy; Bekheet, Shawky Abd El-Hamid

    2017-01-01

    Jojoba is a promising industrial plant, which recommended with pharmaceutical benefits. The present study was conducted to stimulate embryogenic calli formation from jojoba using zeatin and thidiazuron (TDZ), as well as determination of the antioxidant activity of proliferated calli. For callus induction, leaf and stem explants derived from in vitro grown shootlets, were cultured on Murashige and Skoog (MS) medium with different combinations of 0.5 mg L-1 benzyl adenine (BA) or kinetin with 2,4-Dichlorophenoxyacetic acid (2,4-D), Naphthalene acetic acid (NAA) and picloram at 0.5 or 1mg L-1. To stimulate embryogenic calli, friable callus were transferred to woody plant medium (WPM) supplemented with different concentrations of zeatin or TDZ. Antioxidant activity of different treatments was determined using hexane or petroleum ether extraction. Data was analyzed as mean±standard deviation (SD). The MS medium supplemented with 0.5 mg L-1 BA+0.5 or 1 mg L-1 picloram was the best treatment to obtain friable calli from both explants types. WPM medium supplemented with 2 mg L-1 zeatin gave the highest percentage of embryogenic calli derived from leaf explants. While the highest percentage of embryogenic calli derived from stem explants was registered using 1 or 4 mg L-1 TDZ containing medium. Embryogenic calli originated from leaves explants on 1.5 mg L-1 zeatin showed promising activity of antioxidant with hexane extraction. However, embryogenic calli originated from stem explants on 1 mg L-1 TDZ showed the highest antioxidant activity with petroleum ether extraction. TDZ has promising effect on embryogenic callus induction from stem explants. While, zeatin has promising effect on embryogenic callus induction from leaf explants.

  9. A study on friability, hardness and fiber content analysis of fiber enriched milk tablet

    Science.gov (United States)

    Suzihaque, M. U. H.; Irfan, M. H.; Ibrahim, U. K.

    2017-06-01

    This study was performed to analyze the friability, hardness and fiber content of fiber enriched milk tablet derived from five different local fiber sources such as carrot, spinach, dragon fruit, mango and watermelon. Cow milk was mixed to complement with the tablet as a protein source. The powder were spray dried at 100°C, 120°C and 140°C and freeze dried at -60°C. The mixture of fruits and milk were made into equal ratio with the addition of 15 maltodextrin as a carrier. Tablets formed were used for friability and hardness test while dried powder were used for fiber content analysis. Dragon fruit tablet dried at 140°C have the highest friability with 11. 42 of weight loss. The second highest friability was spinach tablet dried at 100°C and 120°C drying temp erature with 9.30 and 9.28 respectively. The lowest friability was exhibited by carrot, mango and watermelon tablet at 100°C and dragon fruit at 120°C while carrot and spinach at 140°C. In contras t, none of the freeze dried tablets showed any weight loss hence they are not friable. For hardness test, all of the freeze dried showed to have higher tensile strength than spray dried, where carrot showed to be the highest at 2.27 Newton and the lowest were spray dried mango at 0.16 Newton. In fiber content analysis, freeze dried mango have the highest fiber content followed by freeze dried carrot and 140°C s pray dried carrot. It can be concluded that the higher the spray dry temperature, the more friable is the tablet. While, high friability leads to lower hardness of tablets. In terms of fiber content, the higher the spray dry temperature, the lower the fiber content found.

  10. An efficient method for the establishment of cell suspension cultures in potato (Solanum tuberosum L.)

    International Nuclear Information System (INIS)

    Sajid, Z.A.

    2016-01-01

    Cell suspension cultures offers an In vitro system that can be used as a tool for various studies involving mutant selection, mass propagation, protoplast isolation, gene transfer and selection of cell-lines which are resistant to various biotic or abiotic stresses. Research work on the development of cell suspension cultures was carried out to establish the most efficient method in Potato (cv. Desiree). Healthy, well-proliferating tissues from different types of callus cultures (compact, friable, embryogenic or non-embryogenic) were inoculated on various media combinations, i.e., MS, MS2 or AA liquid medium containing 18.09 micro M 2, 4-D. A fixed quantity (0.5-1.0 g) of callus tissue from 60-day-old callus cultures was transferred to 10-25 ml of liquid medium in 100 ml Erlenmeyer flask. Cultures were placed on an orbital shaker and agitated at different speeds (75, 100 or 125 rpm) under 16-h photoperiod at 25 ± 2 degree C. Medium was changed after every 3 days and fractionated tissue was filtered after every 6 days through sterile mesh (100-800 micro m) to develop a cell-line by transferring resulting suspension to fresh medium under the same conditions. Results indicated that eight-week-old translucent, friable, off-white callus cultures were an excellent starting material for the initiation of homogeneous cell suspension cultures as compared to other tested sources. Of the three tested media (MS, MS2 or AA medium containing 18.09 micro M 2, 4-D), MS2 was found to be a better medium for the initiation of cell suspension cultures. Cell suspension cultures, placed in 16-h photoperiod at 25 ± 2 degree C and agitated at 120 rpm using a gyratory shaker showed excellent results. Several other factors influencing quick establishment of cell suspension cultures in this cultivar are also discussed in this communication. (author)

  11. Assessment of Fine Aggregates from Different Sources in Ibadan and Environs for Concrete Production

    Directory of Open Access Journals (Sweden)

    W. O. Ajagbe

    2018-03-01

    Full Text Available Assessment of natural sand being used as fine aggregate for concrete production in Ibadan and its environs was carried out. Ten sources (F1 – F10 were selected for the study; four (F5, F6, F7, F8 were river sand sources while six (F1, F2, F3, F4, F9, F10 were burrow pit sand sources. Samples from each source were subjected to sieve analysis, atterberg limit, bulk density, specific gravity, water absorption, sand equivalent, clay lumps and friable particles, amount of materials passing 75μm and organic impurities adopting ASTM standard procedures. Results revealed that sand from river sources met all the criteria for concrete production stated in ASTM standard while sand from burrow pits deviated from limits of the standard in some respects. F10 had water absorption of 2.6% which exceeded maximum 2% specified, F9 was not free from clay lumps and friable particles with a significant value of 6% as against 3% maximum specification. F1, F2, F3, F4, F9 and F10 have more amounts of materials passing the 75μm sieve ranging from 10.8% for F9 to 20.1% for F10 than maximum of 5% in standard specification while F1, F9 and F10 showed an indication of having organic impurities. It is recommended that performance test be conducted on concrete made from burrow pits sand before use for concrete production. The knowledge of this study can be used as a prospecting tool for selecting suitable sand for the production of quality concrete.

  12. Myrciaria dubia (Kunth Mc Vaugh "Camu Camu"

    Directory of Open Access Journals (Sweden)

    Ana M. Córdova

    2014-01-01

    Full Text Available Debido a la alta variabilidad en la producción de vitamina C enMyrciariadubia"camucamu", es necesarioestablecer procedimientos biotecnológicos para la propagación clonal masiva de genotipos promisorios de estaespecie.El objetivo fue establecer un método eficiente para inducir la formación de callosin vitroa partir deexplantesdeM. dubia. Los explantes de hojas y nudos se obtuvieron de ramas cultivadas en el laboratorio y lapulpa a partir defrutos colectados en el campo. Estosfueron desinfectados y sembrados en medio Murashige-Skoog (1962 suplementado con ácido 2,4-diclorofenoxiacético (2,4-D, bencilaminopurina (BAP y kinetina(Kin. Los cultivos fueron mantenidos a 25±2°C, en oscuridad por 2 semanas y posteriormente con unfotoperiodo de 16 horas luz y 8 horas de oscuridad por 6 semanas. El tratamiento con 2 mg/L de 2,4-D y 0,1mg/L de BAP estimuló mayor callogénesis en los tres tipos de explantes. Los callos se generaron a partir de laprimera semana (nudos, cuarta semana (hojas y sexta semana (pulpa y estos fueron friables (hojas y nudosy no friables (pulpa. En conclusión, el método descrito es eficiente para inducir callosin vitroen hojas, nudosy pulpa deM. dubia, siendo los explantes de hojas y nudos los más idóneos para la obtención de callos.

  13. On the Crystallization of Compacted and Chunky Graphite from Liquid Multicomponent Iron-Carbon-Silicon-Based Melts

    Science.gov (United States)

    Stefanescu, D. M.; Huff, R.; Alonso, G.; Larrañaga, P.; De la Fuente, E.; Suarez, R.

    2016-08-01

    Extensive SEM work was carried out on deep-etched specimens to reveal the evolution of compacted and chunky graphite in magnesium-modified multicomponent Fe-C-Si alloys during early solidification and at room temperature. The findings of this research were then integrated in the current body of knowledge to produce an understanding of the crystallization of compacted and chunky graphite. It was confirmed that growth from the liquid for both compacted and chunky graphite occurs radially from a nucleus, as foliated crystals and dendrites. The basic building blocks of the graphite aggregates are hexagonal faceted graphite platelets with nanometer height and micrometer width. Thickening of the platelets occurs through growth of additional graphene layers nucleated at the ledges of the graphite prism. Additional thickening resulting in complete joining of the platelets may occur from the recrystallization of the amorphous carbon that has diffused from the liquid through the austenite, once the graphite aggregate is enveloped in austenite. With increasing magnesium levels, the foliated graphite platelets progressively aggregate along the c-axis forming clusters. The clusters that have random orientation, eventually produce blocky graphite, as the spaces between the parallel platelets disappear. This is typical for compacted graphite irons and tadpole graphite. The chunky graphite aggregates investigated are conical sectors of graphite platelets stacked along the c-axis. The foliated dendrites that originally develop radially from a common nucleus may aggregate along the c-axis forming blocky graphite that sometimes exhibits helical growth. The large number of defects (cavities) observed in all graphite aggregates supports the mechanism of graphite growth as foliated crystals and dendrites.

  14. An integrated structural and geochemical study of fracture aperture growth in the Campito Formation of eastern California

    Science.gov (United States)

    Doungkaew, N.; Eichhubl, P.

    2015-12-01

    Processes of fracture formation control flow of fluid in the subsurface and the mechanical properties of the brittle crust. Understanding of fundamental fracture growth mechanisms is essential for understanding fracture formation and cementation in chemically reactive systems with implications for seismic and aseismic fault and fracture processes, migration of hydrocarbons, long-term CO2 storage, and geothermal energy production. A recent study on crack-seal veins in deeply buried sandstone of east Texas provided evidence for non-linear fracture growth, which is indicated by non-elliptical kinematic fracture aperture profiles. We hypothesize that similar non-linear fracture growth also occurs in other geologic settings, including under higher temperature where solution-precipitation reactions are kinetically favored. To test this hypothesis, we investigate processes of fracture growth in quartzitic sandstone of the Campito Formation, eastern California, by combining field structural observations, thin section petrography, and fluid inclusion microthermometry. Fracture aperture profile measurements of cemented opening-mode fractures show both elliptical and non-elliptical kinematic aperture profiles. In general, fractures that contain fibrous crack-seal cement have elliptical aperture profiles. Fractures filled with blocky cement have linear aperture profiles. Elliptical fracture aperture profiles are consistent with linear-elastic or plastic fracture mechanics. Linear aperture profiles may reflect aperture growth controlled by solution-precipitation creep, with the aperture distribution controlled by solution-precipitation kinetics. We hypothesize that synkinematic crack-seal cement preserves the elliptical aperture profiles of elastic fracture opening increments. Blocky cement, on the other hand, may form postkinematically relative to fracture opening, with fracture opening accommodated by continuous solution-precipitation creep.

  15. Sedimentology and ichnology of Neogene Coastal Swamp deposits in the Niger Delta Basin, Nigeria

    Directory of Open Access Journals (Sweden)

    Ezeh Sunny C.

    2016-09-01

    Full Text Available Often analyses of depositional environments from sparse data result in poor interpretation, especially in multipartite depositional settings such as the Niger Delta. For instance, differentiating channel sandstones, heteroliths and mudstones within proximal environments from those of distal facies is difficult if interpretations rely solely on well log signatures. Therefore, in order to achieve an effective and efficient interpretation of the depositional conditions of a given unit, integrated tools must be applied such as matching core descriptions with wireline log signature. In the present paper cores of three wells from the Coastal Swamp depositional belt of the Niger Delta are examined in order to achieve full understanding of the depositional environments. The well sections comprise cross-bedded sandstones, heteroliths (coastal and lower shoreface and mudstones that were laid down in wave, river and tidal processes. Interpretations were made from each data set comprising gamma ray logs, described sedimentological cores showing sedimentary features and ichnological characteristics; these were integrated to define the depositional settings. Some portions from one of the well sections reveal a blocky gamma ray well log signature instead of a coarsening-upward trend that characterises a shoreface setting while in other wells the signatures for heteroliths at some sections are bell blocky in shaped rather than serrated. Besides, heteroliths and mudstones within the proximal facies and those of distal facies were difficult to distinguish solely on well log signatures. However, interpretation based on sedimentology and ichnology of cores from these facies was used to correct these inconsistencies. It follows that depositional environment interpretation (especially in multifarious depositional environments such as the Niger Delta should ideally be made together with other raw data for accuracy and those based solely on well log signatures should

  16. Investigation on the crystallography of the transformation products of reverted austenite in intercritically reheated coarse grained heat affected zone

    International Nuclear Information System (INIS)

    You, Yang; Shang, Chengjia; Chen, Liang; Subramanian, Sundaresa

    2013-01-01

    Highlights: ► Area of reverted austenite is traced out by crystallographic information. ► Bainite and martensite regions were confirmed within it. ► The martensite region is considered as the blocky MA particles. ► Martensite region has high deformation to initiate fracture. ► More uniform transformation of the reverted austenite is good for toughness. -- Abstract: In present study the intercritically reheated coarse grained heat affected zone (ICCGHAZ) showing the worst impact toughness in the heat affected zone of multi-pass welding was simulated by Gleeble-1500, and its microstructure was investigated in detail by means of scanning electron microscope (SEM) and electron backscattering diffraction (EBSD). With the crystallographic information from EBSD scanning the area of a single reverted austenite grain which formed during the thermal cycles of second pass simulation was traced out. Within it two regions with different characteristic both in morphology and crystallography were found out, showing an un-uniform transformation of the reverted austenite. The region I is a bainitic region containing larger bainitic ferrite grains, while the region II is made up of several clusters containing tiny grains. Based on the crystallographic information each cluster was determined as martensite island thereby should be considered as blocky Martensite/Austenite constituent (M/A), which is hard phase and harmful for toughness. Analysis on the level of deformation shows that the region II is much higher deformed than the region I, indicating there is high stress concentration within the region II. The possible influence of the region I and the region II on fracture is discussed under the early proposed M/A’s fracture-initiating mechanisms. It suggests that the main cause of the toughness reduction is the un-uniform transformation of the reverted austenite, and the toughness performance of the ICCGHAZ could be improved if the transformation of the reverted

  17. La larva de Hyla uruguaya Schmidt, 1944 (Anura: Hylidae, con comentarios sobre su biología y su status taxonómico

    Directory of Open Access Journals (Sweden)

    Kolenc, Francisco

    2003-11-01

    Full Text Available Hyla uruguaya es una especie poco conocida y con relaciones taxonómicas discutidas. Su hallazgo en Uruguay ha sido esporádico. En el presente trabajo se describen su morfología larval, aspectos sobre su biología reproductiva, geonemia y ecología en Uruguay. La larva tiene cuerpo de tipo robusto y elíptico, con ojos laterales, aletas altas con dorsal expandida, espiráculo izquierdo, tubo proctodeal dextrógiro y corto, y fórmula de queratodontes [(1(1-1/(1-1(2], con una fila simple de papilas orales con claro rostral y varias papilas intramarginales subangulares. Una puesta obtenida en el laboratorio consistió de 398 huevos de 1,3 mm de diámetro. El canto de anuncio consta de una sucesión de notas multipulsadas de 22 ms de duración, con una frecuencia dominante promedio de 4146 Hz, emitidas a una frecuencia de 4,2 - 4,8 notas/s. El tren de notas puede durar hasta 13 minutos. Su canto fue registrado en la naturaleza desde fines de agosto y sus larvas se encontraron hasta fines de febrero en charcos de áreas abiertas en paisajes serranos del NE, E y SE del Uruguay. Los resultados obtenidos permitirían reconsiderar el estado de conservación de la especie en Uruguay. Sugerimos su afinidad taxonómica con las especies de Scinax del clado ruber sobre la base de caracteres larvales y discutimos su relación con la especie críptica Hyla pinima. Hyla uruguaya is a poorly known species with controversial taxonomic status. Its finding in Uruguay has been sporadic. In the present work larval morphology, some aspects of reproductive biology, geographical distribution and ecology in Uruguay are addressed. The tadpole has a robust and elliptic body, lateral eyes, high fins, left spiracle, vent tube short and dextral, labial tooth row formula of [(1(1-1/(1-1(2], a single row of oral papillae with a dorsal gap and some submarginal subangular papillae. A spawn of 398 eggs of 1,3 mm diameter was obtained in the laboratory. The advertisement call

  18. Stratigraphic reconstruction of the 13 ka BP debris avalanche deposit at Colima volcano (Mexico): effect of climatic conditions on the flow mobility

    Science.gov (United States)

    Roverato, M.; Capra, L.

    2010-12-01

    Colima volcano is an andesitic stratovolcano located in the western part of the Trans-Mexican Volcanic Belt (TMVB) and at the southern end of the N-S trending Colima graben, about 70 km from the Pacific Ocean coast. It is probably the most active Mexican volcano in historic time and one of the most active of North America. Colima volcano yielded numerous partial edifice collapses with emplacement of debris avalanche deposits (DADs) of contrasting volume, morphology, texture and origin. This work has the aim to provide the evidences of how the climatic condition during the 13 ka flank collapse of the Colima volcano affected the textural characteristic and the mobility of the debris avalanche and debris flow originated from this event that occurred just after the Last Glacial Maximum in Mexico (18.4-14.5 ka 14C BP with snow line at 3600 m a.s.l. up to 13 ka BP). The 13,000 yrs old debris avalanche deposit, here named Tonila (TDAD) presents the typical debris avalanche textural characteristics (angular to sub-angular clasts, coarse matrix, jigsaw fit) but at approximately 13 km from the source, the deposit transforms to an hybrid phase with debris avalanche fragments imbedded in a finer, homogenous and indurated matrix more similar to a debris flow deposit. The debris avalanche deposit is directly overly by debris flows, often more than 10 m thick that contains large amount of logs from pine tree, mostly accumulated toward the base and imbricated down flow. Fluvial deposits also occur throughout all successions, representing periods of stream and river reworking highly localized and re-establishment. All these evidences point to the presence of water in the mass previous to the failure. The event here described represent an anomalous event between the previously described deposit associated to volcanic complex, and evidence as climatic condition can alter and modifies the depositional sequences incrementing the hazard.

  19. Geochemistry and magnetic sediment distribution at the western boundary upwelling system of southwest Atlantic

    Science.gov (United States)

    Cruz, Anna P. S.; Barbosa, Catia F.; Ayres-Neto, Arthur; Munayco, Pablo; Scorzelli, Rosa B.; Amorim, Nívea Santos; Albuquerque, Ana L. S.; Seoane, José C. S.

    2018-02-01

    In order to investigate the chemical and magnetic characteristics of sediments of the western boundary upwelling system of Southwest Atlantic we analyzed magnetic susceptibility, grain size distribution, total organic carbon, heavy mineral abundance, Fe associated with Mössbauer spectra, and Fe and Mn of pore water to evaluate the deposition patterns of sediments. Four box-cores were collected along a cross-shelf transect. Brazil Current and coastal plume exert a primary control at the inner and outer shelf cores, which exhibited similar depositional patterns characterized by a high abundance of heavy minerals (mean 0.21% and 0.08%, respectively) and very fine sand, whereas middle shelf cores presented low abundances of heavy minerals (mean 0.03%) and medium silt. The inner shelf was dominated by sub-angular grains, while in middle and outer shelf cores well-rounded grains were found. The increasing Fe3+:Fe2+ ratio from the inner to the outer shelf reflects farther distance to the sediment source. The outer shelf presented well-rounded minerals, indicating abrasive processes as a result of transport by the Brazil Current from the source areas. In the middle shelf, cold-water intrusion of the South Atlantic Central Water contributes to the primary productivity, resulting in higher deposition of fine sediment and organic carbon accumulation. The high input of organic carbon and the decreased grain size are indicative of changes in the hydrodynamics and primary productivity fueled by the western boundary upwelling system, which promotes loss of magnetization due to the induction of diagenesis of iron oxide minerals.

  20. Rock Physics and Petrographic Parameters Relationship Within Siliciclastic Rocks: Quartz Sandstone Outcrop Study Case

    Science.gov (United States)

    Syafriyono, S.; Caesario, D.; Swastika, A.; Adlan, Q.; Syafri, I.; Abdurrokhim, A.; Mardiana, U.; Mohamad, F.; Alfadli, M. K.; Sari, V. M.

    2018-03-01

    Rock physical parameters value (Vp and Vs) is one of fundamental aspects in reservoir characterization as a tool to detect rock heterogenity. Its response is depend on several reservoir conditions such as lithology, pressure and reservoir fluids. The value of Vp and Vs is controlled by grain contact and contact stiffness, a function of clay mineral content and porosity also affected by mineral composition. The study about Vp and Vs response within sandstone and its relationship with petrographic parameters has become important to define anisotrophy of reservoir characteristics distribution and could give a better understanding about local diagenesis that influence clastic reservoir properties. Petrographic analysis and Vp-Vs calculation was carried out to 12 core sample which is obtained by hand-drilling of the outcrop in Sukabumi area, West Java as a part of Bayah Formation. Data processing and interpretation of sedimentary vertical succession showing that this outcrop comprises of 3 major sandstone layers indicating fluvial depositional environment. As stated before, there are 4 petrographic parameters (sorting, roundness, clay mineral content, and grain contact) which are responsible to the differences of shear wave and compressional wave value in this outcrop. Lithology with poor-sorted and well- roundness has Vp value lower than well-sorted and poor-roundness (sub-angular) grain. For the sample with high clay content, Vp value is ranging from 1681 to 2000 m/s and could be getting high until 2190 to 2714 m/s in low clay content sample even though the presence of clay minerals cannot be defined neither as matrix nor cement. The whole sample have suture grain contact indicating telogenesis regime whereas facies has no relationship with Vp and Vs value because of the different type of facies show similar petrographic parameters after diagenesis.

  1. STRATIGRAPHY OF THE PB-1 WELL, NOPAL I URANIUM DEPOSIT, SIERRA PENA BLANCA, CHIHUAHUA, MEXICO

    Energy Technology Data Exchange (ETDEWEB)

    NA

    2005-06-25

    Three wells, PB-1, PB-2, and PB-3, were drilled in 2003 at the Nopal I uranium deposit as part of a natural analogue study to evaluate radionuclide transport processes. The wells penetrate through the Tertiary volcanic section down to the Cretaceous limestone basement, and intersect the top of the regional aquifer system. The PB-1 well, drilled immediately adjacent to the Nopal I ore body, was cored to a depth of 250 m, thus providing an opportunity to document the local stratigraphy. The uppermost unit encountered in the PB-1 well is the Nopal Formation, a densely welded, crystal-rich rhyolitic ash-flow tuff. The cored section is highly altered and devitrified, with kaolinite, quartz, chlorite, and montmorillonite replacing feldspars and much of the groundmass. Breccia zones within the tuff contain fracture fillings of hematite, limonite, and goethite. A zone of intense clay alteration encountered in the depth interval 17.45-22.30 m was interpreted to represent the basal vitrophyre of this unit. Underlying the basal vitrophyre is the Coloradas Formation, which consists of a welded, lithic-rich rhyolitic ash-flow tuff. The cored section of this unit has undergone devitrification and oxidation, and has a similar alteration mineralogy to that observed in the Nopal tuff. The Nopal I ore body is restricted to a brecciated zone that intersects these two volcanic units. A sharp contact between the Coloradas tuff and the underlying Pozos Formation was observed at a depth of 136.38 m. The Pozos Formation in the PB-1 core consists of interbedded, poorly sorted sandstone and conglomerate layers. The conglomeratic clasts consist of subangular to subrounded fragments of volcanic rocks, limestone, and chert. Thin (2-6 m) intervals of intercalated pumiceous tuffs were observed within this unit. The contact between the Pozos Formation and the underlying Cretaceous limestone basement was observed at a depth of 244.4 m.

  2. Sedimentological reservoir characteristics of the Paleocene fluvial/lacustrine Yabus Sandstone, Melut Basin, Sudan

    Science.gov (United States)

    Mahgoub, M. I.; Padmanabhan, E.; Abdullatif, O. M.

    2016-11-01

    Melut Basin in Sudan is regionally linked to the Mesozoic-Cenozoic Central and Western African Rift System (CWARS). The Paleocene Yabus Formation is the main oil producing reservoir in the basin. It is dominated by channel sandstone and shales deposited in fluvial/lacustrine environment during the third phase of rifting in the basin. Different scales of sedimentological heterogeneities influenced reservoir quality and architecture. The cores and well logs analyses revealed seven lithofacies representing fluvial, deltaic and lacustrine depositional environments. The sandstone is medium to coarse-grained, poorly to moderately-sorted and sub-angular to sub-rounded, arkosic-subarkosic to sublitharenite. On the basin scale, the Yabus Formation showed variation in sandstone bodies, thickness, geometry and architecture. On macro-scale, reservoir quality varies vertically and laterally within Yabus Sandstone where it shows progressive fining upward tendencies with different degrees of connectivity. The lower part of the reservoir showed well-connected and amalgamated sandstone bodies, the middle to the upper parts, however, have moderate to low sandstone bodies' connectivity and amalgamation. On micro-scale, sandstone reservoir quality is directly affected by textures and diagenetic changes such as compaction, cementation, alteration, dissolution and kaolinite clays pore fill and coat all have significantly reduced the reservoir porosity and permeability. The estimated porosity in Yabus Formation ranges from 2 to 20% with an average of 12%; while permeability varies from 200 to 500 mD and up to 1 Darcy. The understanding of different scales of sedimentological reservoir heterogeneities might contribute to better reservoir quality prediction, architecture, consequently enhancing development and productivity.

  3. Caracterización geomorfológica de las dunas longitudinales del Istmo de Médanos, estado Falcón, Venezuela

    Directory of Open Access Journals (Sweden)

    Ronna Camacho

    2012-02-01

    Full Text Available El trabajo analiza la geomorfología de dunas costeras longitudinales del Istmo de Médanos, costa noroccidental de Venezuela. La metodología consistió en consultas bibliográficas, cartográficas, fotogramétricas y satelitales, trabajos de campo y análisis sedimentológico. Los resultados indican que estas dunas están compuestas por arenas de grano fino en un 84.6%, muy bien seleccionadas en más del 60%, principalmente subangulares, con asimetría negativa predominante, distribución leptocurtica, y bajo contenido de carbonato de calcio cercano al 10%. Los datos sugieren que los sedimentos son de origen terrígeno y escasa distancia de transporte hasta el lugar de acumulación. Los vientos predominantes actuales son del noreste, con componentes direccionales secundarios que retrabajan los sedimentos generando dunas transversales, barcanas y longitudinales; las dunas longitudinales son paralelas a la dirección del viento y se presentan colonizadas por vegetación xerofítica favorecida por la inactividad de las mismas. Estas dunas se originaron probablemente por una conjunción de factores como: disponibilidad de sedimentos en una amplia llanura costera relacionada con un nivel marino regresivo, vientos fuertes y persistentes, orientación oblicua de la costa respecto a la dirección del viento, una topografía continental favorable adyacente a la playa, bajo condiciones climáticas distintas a las actuales.

  4. Surface Textural Analysis of Quartz Grains from Modern Point Bar Deposits in Lower Reaches of the Yellow River

    Science.gov (United States)

    Cheng, Yong; Liu, Cong; Lu, Ping; Zhang, Yu; Nie, Qi; Wen, Yiming

    2018-01-01

    The surfaces of quartz grains contain characteristic textures formed during the process of transport, due to their stable physical and chemical properties. The surface textures include the information about source area, transporting force, sedimentary environment and evolution history of sediment. Surface textures of quartz grains from modern point bar deposits in the lower reaches of the Yellow River are observed and studied by scanning electron microscopy (SEM). Results indicate that there are 22 kinds of surface textures. The overall surface morphology of quartz grains shows short transporting time and distance and weak abrasive action of the river water. The combined surface textures caused by mechanical action indicate that quartz grains are transporting in a high-energy hydrodynamic condition and suffer a strong mechanical impact and abrasion. The common solution pits prove that the chemical property of transportation medium is very active and quartz grains receive an obvious chemical action. The combination of these surface textures can be an identification mark of fluvial environment, and that is: quartz grains are main subangular outline, whose roundness is higher with the farther motion distance; Surface fluctuation degree of quartz grains is relatively high, and gives priority to high and medium relief; V-shaped percussion marks are very abundant caused by mechanical action; The conchoidal of different sizes and steps are common-developed with paragenesis relationship; Solution pits are common-developed as well. The study makes up for the blank of surface textures analysis of quartz grains from modern fluvial deposits in China. It provides new ideas and evidence for studies of the sedimentary process and environmental significance, although the deep meanings of these micro textures remain to be further researched.

  5. SEDIMENTARY EVIDENCE OF PALAEO-TSUNAMI DEPOSITS ALONG THE LOUKKOS ESTUARY (MOROCCAN ATLANTIC COAST

    Directory of Open Access Journals (Sweden)

    Nadia Mhammdi

    2015-05-01

    Full Text Available Analysis of the CARLA-11 core drilled along the lower Loukkos valley near Larache in northern Morocco shows a thin level of shelly sand at 465 to 482 cm depth, whose sedimentological features are those of a high-energy, certainly a tsunami deposit. The level can be subdivided into 3 subunits: Subunit 1 (6 cm shows a sharp erosive base and comprises basal medium to coarse sands containing numerous marine shell fragments of bivalves, plant fragments and rip-up clasts of organic matter. Subunit 2 (7 cm is a flame structure consisting of coarse sand containing a layer of organic matter and another one of greyish clay. Subunit 3 (4 cm is similar to subunit 1 and consists of coarse sands containing numerous complete or broken shells of bivalves, plant fragments and dark organic matter. The deposit is mostly composed of subangular to subrounded quartz grains derived from nearby Miocene sandstones. Benthic and planctonic foraminifera are common within the samples. Magnetic susceptibility measurements show two major lows at ~350 cm, and especially at 477 cm within the high-energy deposit. Subunit 1 can be interpreted as the result of the first wave uprush of a tsunami, the fine mud level of subunit 2 capping subunit 1 can be interpreted as emplaced during a decantation phase, and subunit 2 probably corresponds to a second wave uprush, Subunit 3 might be interpreted as the result of the backwash (outflow phase. The age of this event can be roughly dated between 5 and 3 ky BP according to recent dating of nearby levels.

  6. Particle-bubble aggregate stability on static bubble generated by single nozzle on flotation process

    Science.gov (United States)

    Warjito, Harinaldi, Setyantono, Manus; Siregar, Sahala D.

    2016-06-01

    There are three sub-processes on flotation. These processes are intervening liquid film into critical thickness, rupture of liquid film forming three phase contact line, and expansion three phase contact line forming aggregate stability. Aggregate stability factor contribute to determine flotation efficiency. Aggregate stability has some important factors such as reagent and particle geometry. This research focussed on to understand effect of particle geometry to aggregate stability. Experimental setup consists of 9 x 9 x26 cm flotation column made of glass, bubble generator, particle feeding system, and high speed video camera. Bubble generator made from single nozzle with 0.3 mm diameter attached to programmable syringe pump. Particle feeding system made of pipette. Particle used in this research is taken from open pit Grasberg in Timika, Papua. Particle has sub-angular geometry and its size varies from 38 to 300 µm. Bubble-particle interaction are recorded using high speed video camera. Recordings from high speed video camera analyzed using image processing software. Experiment result shows that aggregate particle-bubble and induction time depends on particle size. Small particle (38-106 µm) has long induction time and able to rupture liquid film and also forming three phase contact line. Big particle (150-300 µm) has short induction time, so it unable to attach with bubble easily. This phenomenon is caused by apparent gravity work on particle-bubble interaction. Apparent gravity worked during particle sliding on bubble surface experience increase and reached its maximum magnitude at bubble equator. After particle passed bubble equator, apparent gravity force experience decrease. In conclusion particle size from 38-300 µm can form stable aggregate if particle attached with bubble in certain condition.

  7. Sedimentological and Scanning Electron Miscroscopic Descriptions of Afowo Oil Sand Deposits, South Western Nigeria

    Directory of Open Access Journals (Sweden)

    Akinmosin A

    2017-12-01

    Full Text Available Sedimentological and scanning electron microscopic analyses of some shallow reservoir tar sand samples in parts of Southwestern Nigeria were carried out with the aim of characterizing the reservoir properties in relation to bitumen saturation and recovery efficiency. The production of impregnated tar from the sands requires the reservoir to be of good quality. A total of thirty samples were collected at different localities within the tar sand belt (ten out of these samples were selected for various reservoir quality analyses based on their textural homogeneity. The result of particle size distribution study showed that bulk of the sands is medium – coarse grained and moderately sorted. The grain morphologies are of low to high sphericity with shapes generally sub-angular to sub-rounded, implying that the sands have undergone a fairly long transportation history with depositional energy having a moderate to high velocity. The quartz content was made up of about 96% of the total mineralogical components; the sediments of the Afowo Formation can be described to be mineralogically and texturally stable. The result of the scanning electron microscopy (SEM analysis revealed that the oil sands contained minerals which had been precipitated and occurred as pore filling cement; these minerals include sheet kaolinite, block kaolinite, vermiform kaolinite, pyrite crystals and quartz. The SEM images also showed micro-pores ranging from 0.057µm to 0.446µm and fractures. The study showed that the clay minerals contained in the Afowo reservoir rocks were mainly kaolinite. Kaoline unlike some other clays (e.g Montimorillonite does not swell with water, hence it is not expected to have any negative effects on the reservoir quality, especially during enhanced oil recovery operations.

  8. Late Devonian glacial deposits from the eastern United States signal an end of the mid-Paleozoic warm period

    Science.gov (United States)

    Brezinski, D.K.; Cecil, C.B.; Skema, V.W.; Stamm, R.

    2008-01-01

    A Late Devonian polymictic diamictite extends for more than 400??km from northeastern Pennsylvania across western Maryland and into east-central West Virginia. The matrix-supported, unbedded, locally sheared diamictite contains subangular to rounded clasts up to 2??m in diameter. The mostly rounded clasts are both locally derived and exotic; some exhibit striations, faceting, and polish. The diamictite commonly is overlain by laminated siltstone/mudstone facies associations (laminites). The laminites contain isolated clasts ranging in size from sand and pebbles to boulders, some of which are striated. The diamictite/laminite sequence is capped by massive, coarse-grained, pebbly sandstone that is trough cross-bedded. A stratigraphic change from red, calcic paleo-Vertisols in strata below the diamictite to non-calcic paleo-Spodosols and coal beds at and above the diamictite interval suggests that the climate became much wetter during deposition of the diamictite. The diamictite deposit is contemporaneous with regressive facies that reflect fluvial incision during the Late Devonian of the Appalachian basin. These deposits record a Late Devonian episode of climatic cooling so extreme that it produced glaciation in the Appalachian basin. Evidence for this episode of climatic cooling is preserved as the interpreted glacial deposits of diamictite, overlain by glaciolacustrine varves containing dropstones, and capped by sandstone interpreted as braided stream outwash. The Appalachian glacigenic deposits are contemporaneous with glacial deposits in South America, and suggest that Late Devonian climatic cooling was global. This period of dramatic global cooling may represent the end of the mid-Paleozoic warm interval that began in the Middle Silurian. ?? 2008 Elsevier B.V. All rights reserved.

  9. Soil physico-chemical characterization in the different soil layers of National Maize Research Program, Rampur, Chitwan, Nepal

    Directory of Open Access Journals (Sweden)

    Dinesh Khadka

    2017-12-01

    Full Text Available Soil pit digging and their precise study is a decision making tool to assess history and future of soil management of a particular area. Thus, the present study was carried out to differentiate soil physico-chemical properties in the different layers of excavated pit of the National Maize Research Program, Rampur, Chitwan, Nepal. Eight pits were dug randomly from three blocks at a depth of 0 to 100 cm. The soil parameters were determined in-situ, and in laboratory for texture, pH, OM, N, P (as P2O5, K (as K2O, Ca, Mg, S, B, Fe, Zn, Cu and Mn of collected soils samples of different layers following standard analytical methods at Soil Science Division, Khumaltar. The result revealed that soil structure was sub-angular in majority of the layers, whereas bottom layer was single grained. The value and chrome of colour was increasing in order from surface to bottom in the majority pits. Similarly, the texture was sandy loam in majority layers of the pits. Moreover, four types of consistence (loose to firm were observed. Furthermore, mottles and gravels were absent in the majority layers. Likewise, soil was very to moderately acidic in observed layers of majority pits, except bottom layer of agronomy block was slightly acidic. Regarding fertility parameters (OM, macro and micronutrients, some were increasing and vice-versa, while others were intermittent also. Therefore, a single layer is not dominant for particular soil physico-chemical parameters in the farm. In overall, surface layer is more fertile than rest of the layers in all the pits.

  10. STRATIGRAPHY OF THE PB-1 WELL, NOPAL I URANIUM DEPOSIT, SIERRA PENA BLANCA, CHIHUAHUA, MEXICO

    International Nuclear Information System (INIS)

    2005-01-01

    Three wells, PB-1, PB-2, and PB-3, were drilled in 2003 at the Nopal I uranium deposit as part of a natural analogue study to evaluate radionuclide transport processes. The wells penetrate through the Tertiary volcanic section down to the Cretaceous limestone basement, and intersect the top of the regional aquifer system. The PB-1 well, drilled immediately adjacent to the Nopal I ore body, was cored to a depth of 250 m, thus providing an opportunity to document the local stratigraphy. The uppermost unit encountered in the PB-1 well is the Nopal Formation, a densely welded, crystal-rich rhyolitic ash-flow tuff. The cored section is highly altered and devitrified, with kaolinite, quartz, chlorite, and montmorillonite replacing feldspars and much of the groundmass. Breccia zones within the tuff contain fracture fillings of hematite, limonite, and goethite. A zone of intense clay alteration encountered in the depth interval 17.45-22.30 m was interpreted to represent the basal vitrophyre of this unit. Underlying the basal vitrophyre is the Coloradas Formation, which consists of a welded, lithic-rich rhyolitic ash-flow tuff. The cored section of this unit has undergone devitrification and oxidation, and has a similar alteration mineralogy to that observed in the Nopal tuff. The Nopal I ore body is restricted to a brecciated zone that intersects these two volcanic units. A sharp contact between the Coloradas tuff and the underlying Pozos Formation was observed at a depth of 136.38 m. The Pozos Formation in the PB-1 core consists of interbedded, poorly sorted sandstone and conglomerate layers. The conglomeratic clasts consist of subangular to subrounded fragments of volcanic rocks, limestone, and chert. Thin (2-6 m) intervals of intercalated pumiceous tuffs were observed within this unit. The contact between the Pozos Formation and the underlying Cretaceous limestone basement was observed at a depth of 244.4 m

  11. Jurassic and Cretaceous clays of the northern and central North Sea hydrocarbon reservoirs reviewed

    Energy Technology Data Exchange (ETDEWEB)

    Wilkinson, M.; Haszeldine, R.S.; Fallick, A.E.

    2006-03-15

    The principal clays of the northern and central North Sea are illite (sometimes with interlayered smectite) and kaolin. Chlorite is only locally important. Although it has been proposed that kaolin within North Sea sandstones is detrital in origin, the majority of workers have concluded that it is authigenic, largely the product of feldspar alteration. Kaolin is found within a wide range of sedimentary settings (and within shales) apparently defying the notion that kaolin is an indicator of meteoric water deposition. Within sandstones, the earliest authigenic kaolin has a vermiform morphology, the distribution of which is controlled by the availability of detrital mica to act as a nucleus, and the composition of the post-depositional porewaters. This vermiform kaolin formed in meteoric water, the presence of which is easily accounted for below sub-aerial exposure surfaces in non-marine formations, and below unconformities over marine units. In fully marine sands, and even marine shale units, kaolin still occurs. It has therefore been suggested that even these locations have been flushed with meteoric water. Early vermiform kaolin recrystallizes to a more blocky morphology as burial proceeds, at least in the Brent Group. Blocky kaolin has been reported as growing before, synchronously with, and after the formation of quartz overgrowths, though oxygen isotope studies support low-temperature growth, pre-quartz. Blocky kaolin may form during meteoric flushing associated with lower Cretaceous uplift and erosion, though it is found in fault blocks that are thought to have remained below sea level. Here, the kaolin may form in stagnant meteoric water, relics of the post-depositional porewater. It has also been proposed that the blocky kaolin grew in ascending basinal waters charged with carboxylic acids and CO{sub 2}, though this hypothesis is not supported by stable oxygen isotope data. Some of the blocky kaolin is dickite, the stable polymorph above 100{sup o}C. Fibrous

  12. Quantificação da resistência tênsil e da friabilidade de um latossolo vermelho distroférrico sob plantio direto Quantification of tensile strength and friability of an oxisol (Acrudox under no-tillage

    Directory of Open Access Journals (Sweden)

    Cássio Antonio Tormena

    2008-06-01

    meet these requirements. The objective of this study was to evaluate the tensile strength and friability of an Oxisol (Acrudox under no-tillage with crop rotation and crop succession. The soil management treatments consisted of: crop succession with wheat and soybean (SDS; crop rotation with corn-oats-soybean-oats-soybean-wheat (SDR and SDR plus periodic soil chiseling (SDE. Ten soil blocks (0.15 x 0.20 x 0.10 m were randomly collected from the 0-0.20 m layer for each treatment, on two sampling dates (October 2003 and April 2004. The soil tensile strength and soil friability was estimated in 450 soil aggregates from each treatment and sampling date. The soil organic carbon content of the aggregates was also measured. There was no effect of soil organic carbon on soil tensile strength and friability. Results showed lower tensile strength in SDE soil collected in 2003. Crop succession (SDS temporarily changed the friability classification from very friable to friable. Crop rotation (SDR was effective in maintaining the soil structure at the very friable class, resulting in a better structure and soil physical quality. The parameters tensile strength and friability proved sensitive enough to evaluate soil structural quality under the crop management systems studied.

  13. Callus formation in vitro and internodal stem apices in savory = Calogênese in vitro de segmentos apicais caulinares e internodais em segurelha (Satureja hortensis L.

    Directory of Open Access Journals (Sweden)

    Marcio Carlos Navroski

    2012-12-01

    Full Text Available We sought to evaluate with this work different growth regulators on callus formation in shoot apical and internodal stem segments of Satureja hortensis. The explants were isolated from in vitro seedlings and cultured on MS nutrient medium supplemented with NAA (0 and 1 μM and BAP (0, 5, 10, 15 and 20 μM. The presence of auxin NAA gave higher marks to the calluses at 30 days of evaluation, these notes also increased with the addition of BAP. There were significant interactions between factors in evaluating NAA and BAP for 60 days, both in apical stem segments as in internodal stem segments. To stemapices percentage of friable callus tends to decrease with increasing concentration of BAP. As for compact calluses increased BAP leads to an increase in the percentage of this type of callus. The presence of NAA increased callus formation in both friable and compact calluses on. This trend was also observed in internodal stem segments. The callus formation was highly rhizogenic observed in the presence of NAA, hardly occurs in the absence of auxin. The use of BAP is recommended in case of regeneration of plants through micropropagation, if the goal is the production of metabolites, the use of BAP can be harmful by reducing the production of friable callus.= Buscou-se com este trabalho avaliar diferentes reguladores de crescimento sobre a calogênese em segmentos caulinares apicais e internodais de Satureja hortensis L.. Os explantes foram isolados de plântulas germinadas in vitro e cultivados em meio nutritivo MS acrescido de ANA (0 e 1 μM e de BAP (0; 5; 10; 15 e 20 μM. A presença da auxina ANA proporcionou notas mais altas para os calos aos 30 dias de avaliação, estas notas também aumentaram com o acréscimo da citocinina BAP. Houve interações significativas entre os fatores ANA e BAP na avaliação aos 60 dias, nos dois tipos de segmentos caulinares(apicais e internodais. Nos segmentos apicais caulinares a porcentagem de calos fri

  14. THE EFFECT OF PICLORAM AND LIGHT ON SOMATIC EMBRYOGENESIS REGENERATION OF PINEAPPLE

    Directory of Open Access Journals (Sweden)

    Ika Roostika

    2012-10-01

    Full Text Available Smooth Cayenne is the largest pineapple type cultivated in Indonesia, but its vegetative planting materials for mass propagation are limited. Somatic embryogenesis is a potential method to be applied. The aim of this study was to investigate the somatic embryogenesis regeneration under the effect of picloram and light. Callus formation was induced by picloram (21, 41 and 62 μM added with 9 μM thidiazuron. The calli were transferred onto MS or Bac medium  enriched with N-organic compounds with or without addition of 21 μM picloram under dark or light condition. The compact calli were subcultured onto MS medium supplemented with 4.65 μM kinetin, while the friable calli were  transferred onto BIG medium (modified MS + 1.1 μM benzyl adenine + 0.9 μM indole butyric acid + 0.09 μM giberelic acid or B medium (MS + 0.018 mM benzyl adenine. The results showed that the events of somatic embryogenesis were started from cell polarization, asymmetrical division, proembryo formation as  embryogenic tissues and friable embryogenic tissues, and embryo development. The best treatment for callus induction was 21 μM picloram. The addition of 21 μM picloram on N-organic enriched medium and the use of light condition  proliferated embryogenic calli. The N-organic enriched Bac medium and light condition yielded the highest number of mature somatic embryos (17 embryos perexplant in 2 months. The B medium was better than BIG medium to develop  somatic embryos from friable embryogenic tissues. The somatic embryogenesis method presented is potential for pineapple mass propagation and artificial seedproduction.Abstrak Bahasa IndonesiaSmooth Cayenne merupakan kultivar nenas yang banyak dibudidayakan di  Indonesia, namun ketersediaan benih untuk perbanyakan massal masih terbatas. Embriogenesis somatikadalah metode yang potensial untuk produksi bibit secara massal. Tujuan penelitian adalah untuk mempelajari pengaruh pikloram dan pencahayaan terhadap regenerasi

  15. Meso- and microscale vein structures in fore-arc basalts and boninites related to post-magmatic tectonic deformation in the outer Izu-Bonin-Mariana fore arc system: preliminary results from IODP Expedition 352

    Science.gov (United States)

    Quandt, Dennis; Micheuz, Peter; Kurz, Walter

    2016-04-01

    The International Ocean Discovery Program (IODP) Expedition 352 aimed to drill through the entire volcanic sequence of the Izu-Bonin-Mariana fore arc. Two drill sites are situated on the outer fore arc composed of fore arc basalts (FAB) whereas two more sites are located on the upper trench slope penetrating the younger boninites. First results from IODP Expedition 352 and preliminary post-cruise data suggest that FAB were generated by decompression melting during near-trench sea-floor spreading, and that fluids from the subducting slab were not involved in their genesis. Subduction zone fluids involved in boninite genesis appear to have been derived from progressively higher temperatures and pressures over time as the subducting slab thermally matured. Structures within the drill cores combined with borehole and site survey seismic data indicate that tectonic deformation in the outer Izu-Bonin-Mariana fore arc is mainly post-magmatic associated with the development of syn-tectonic sedimentary basins. Within the magmatic basement deformation was accommodated by shear along cataclastic fault zones and the formation of tension fractures, shear fractures and hybrid (tension and shear) fractures. Veins form by mineral filling of tension or hybrid fractures and show no or limited observable macroscale displacement along the fracture plane. (Low Mg-) Calcite and/or various types of zeolite are the major vein constituents, where the latter are considered to be alteration products of basaltic glass. Micrite contents vary significantly and are related to neptunian dikes. In boninites calcite develops mainly blocky shapes but veins with fibrous and stretched crystals also occur in places indicating antitaxial as well as ataxial growth, respectively. In FAB calcite forms consistently blocky crystals without any microscopic identifiable growth direction suggesting precipitation from a highly supersaturated fluid under dropping fluid pressure conditions. However, fluid pressure

  16. The affection of the disturbance of the hydrodynamics of blood in case of stress on pathological increase of level of low density lipoproteins in blood. The formation of cylindrical plaques, and their participation in the development of acute ischemic disorders of heart and brain.

    Science.gov (United States)

    Rusanov, S E

    2017-09-01

    In this article is given the new insight about the affection of stress on the increase of level of low density lipoproteins (LDL) in the blood, which is connected with the disturbance of hydrodynamics in the bloodstream, the attention was paid to the cylindrical cholesterol plaque, and it's classification. The disturbance of hydrodynamics of blood under the stress leads to the formation of a cylindrical cholesterol plaque, which repeats the contour of the vessel, and leads to the ischemic disorders of the heart and brain. The cylindrical cholesterol plaque goes through several stages of development: friable, yielding, dense, old. In the case of destruction of friable, fresh cholesterol plaque, releases a big quantity of low-density lipoproteins. This leads to the pathological increase of level of LDL in the blood. In the case of long disturbance of hydrodynamics, occurs the formation of strong links between low-density lipoproteins. Yielding cholesterol plaque is formed. Further maturation of cylindrical cholesterol plaque, leads to it's densifying and damage. We may emphasize, that short periods of strong contraction and expansion of vessels lead to the increase of level of LDL in the blood. Self-dependent restoration of normal level of LDL in blood occurs in the case of restoration of pressure in the limits of numbers, which are specific for particular person, and which don't exceed the physiological standard. Among patients with long duration of stress, the duration of vasospasm increases. LDL, without having a possibility to crumble, begin to stick together and form the yielding cylindrical plaque. It is characterized by having of not so strong connection with the vascular wall, and maintains only at the expanse of iteration of the vascular wall, it has cylindrical shape, is elastic and yellow. The thickness and length of walls depends on the degree of cross-clamping during the time of formation of yielding cylindrical plaque. In the case of stopping of spasm

  17. Colonoscopic perforation leading to a diagnosis of Ehlers Danlos syndrome type IV: a case report and review of the literature

    Directory of Open Access Journals (Sweden)

    Wolfe John

    2011-06-01

    Full Text Available Abstract Introduction Colonoscopic perforation is a rare but serious complication of colonoscopy. Factors known to increase the risk of perforation include colonic strictures, extensive diverticulosis, and friable tissues. We describe the case of a man who was found to have perforation of the sigmoid colon secondary to an undiagnosed connective tissue disorder (Ehlers-Danlos syndrome type IV while undergoing surveillance for hereditary non-polyposis colorectal cancer. Case presentation A 33-year-old Caucasian man presented to our hospital with an acute abdomen following a colonoscopy five days earlier as part of hereditary non-polyposis colorectal cancer screening. His medical history included bilateral clubfoot. His physical examination findings suggested left iliac fossa peritonitis. A computed tomographic scan revealed perforation of the sigmoid colon and incidentally a right common iliac artery aneurysm as well. Hartmann's procedure was performed during laparotomy. The patient recovered well post-operatively and was discharged. Reversal of the Hartmann's procedure was performed six months later. This procedure was challenging because of dense adhesions and friable bowel. The histology of bowel specimens from this surgery revealed thinning and fibrosis of the muscularis externa. The patient was subsequently noted to have transparency of truncal skin with easily visible vessels. An underlying collagen vascular disorder was suspected, and genetic testing revealed a mutation in the collagen type III, α1 (COL3A1 gene, which is consistent with a diagnosis of Ehlers-Danlos syndrome type IV. Conclusions Ehlers-Danlos syndrome type IV, the vascular type, is a rare disorder caused by mutations in the COL3A1 gene on chromosome 2q31. It is characterized by translucent skin, clubfoot, and the potentially fatal complications of spontaneous large vessel rupture, although spontaneous uterine and colonic perforations have also been reported in the

  18. Effect of biocrust: study of mechanical and hydraulic properties and erodibility

    Science.gov (United States)

    Slavík, Martin; Bruthans, Jiří; Schweigstillová, Jana

    2016-04-01

    It is well-known that lichens and other organisms forming crust on soil or rock surface play important role in weathering but may also protect underlying material from fast erosion. So far, there have been only few measurements comparing mechanical or hydraulic properties of biocrust with its subsurface on locked sand and friable sandstones, so the overall effect of the biocrust is not well-understood. Objective of our study is to quantify the effect of the biocrust on mechanical and hydraulic properties of friable sandstone and locked sand of Cretaceous age in six different localities with varying aspect and inclination and age of exposure in sandpit Strelec (Czech Rep.). On the artificial exposures, biocrust developed within last 10-30 years. Beside measurements of mechanical and hydraulic properties, SEM and mercury intrusion porosimetry in crust and subsurface was performed. Drilling resistance technique was found an excellent method to distinguish the biocrust from its subsurface (~3 mm thick biocrust has up to 12 times higher drilling resistance than underlying material). Surface zone with the biocrust has 3 - 25 times higher tensile strength than the subsurface material (1 - 25 kPa). In comparison with the subsurface, the biocrust is considerably less erodible (based on water jet testing). Biocrust saturated hydraulic conductivity is 15 - 240 times lower than the subsurface (6*10 -5 - 1*10 -4 m/s) and its permeability for water vapor is 4 - 9 times lower than subsurface. Presence of the biocrust slows down capillary absorption of water 4 - 25 times. The biocrust is thus forming firm surface which protects underlying material from rain and flowing water erosion and which considerably modifies its hydraulic properties. Material with crust exposed to calcination, leaching by concentrated peroxide and experiments with zymoliase enzyme strongly indicate that major contribution to crust hardening is provided by organic matter. Based on DNA sequencing the crust is

  19. Queratoquistes maxilares: marsupialización Keratocysts of the jaw: marsupialization

    Directory of Open Access Journals (Sweden)

    D. Martínez Pérez

    2006-08-01

    Full Text Available El queratoquiste odontogénico es una tumoración quística cuya cápsula está formada por un epitelio escamoso derivado de la lámina dental o el epitelio odontogénico primordial. Representa un 10% de todas las lesiones quísticas de los maxilares. Radiológicamente, es raro que presentes reabsorciones radiculares. El diagnóstico está basado en las características histológicas. El diagnóstico diferencial más importante es el quiste folicular que se caracteriza por un revestimiento escamoso de espesor variable. El tratamiento de los queratoquistes odontogénicos es objeto de constante discusión ya que la tasa de recidiva publicada es elevada (en torno al 30%. El tratamiento estándar es la enucleación, pero dado que la cápsula es típicamente fina y friable, se suele fragmentar durante la extirpación. La resección incompleta de la cápsula así como la presencia de microquistes en el tejido conectivo circundante predispone a la recidiva o persistencia de la tumoración. La alternativa es el tratamiento por medio de descompresión y marsupialización.The odontogenic keratocyst is a tumor-like cystic with a capsule that is formed of squamous epithelium originating from dental lamina or from primordial odontogenic epithelium. Radiologically, radicular resorption is rare. The most important differential diagnosis is the follicular cyst that has a characteristic squamous coating of a variable thickness. Treatment for odontogenic keratocysts is the object of constant discussion as the rate of recurrence published is high (around 30%. The standard treatment is enucleation, but given that the capsule is very fine and friable, it tends to break into fragments during extraction. Incomplete resection of the capsule, as well as the presence of microcysts in the surrounding connective tissue, makes recurrence or tumor persistence more likely. The alternative is treatment by means of decompression and marsupialization.

  20. Physical and mechanical characterisation of historic mortars. Application to the evaluation of the state of conservation

    Directory of Open Access Journals (Sweden)

    Magalhães, A.

    2009-08-01

    Full Text Available An understanding of the physical and mechanical characteristics of historic mortars is of vital importance in the selection of repair mortars for historic buildings. As a result, a need has arisen for test methods that can be used to assess those characteristics in irregular, friable samples.The present paper discusses the results of the experimental characterization of historic Portuguese mortars. The test methods used to evaluate water resistance and compressive strength are described. The compressive strength values found for new mortars using the method proposed and the method specified in European standards are compared and the results used to draw conclusions on the potential of the new technique.The correlation between the initial degree of deterioration determined by visual inspection and the experimental data is discussed.El conocimiento de las características físicas y mecánicas de los morteros antiguos es muy importante a la hora de seleccionar morteros de reparación y de planear adecuadamente cualquier intervención de reparación. Así, se hace necesario definir los métodos de ensayo de caracterización aplicables a las muestras irregulares y friables para evaluar dichas características. En el presente trabajo se presentan y analizan algunos resultados de caracterización experimental de morteros antiguos portugueses, y se describen los métodos de ensayo utilizados para evaluar el comportamiento al agua y la resistencia a la compresión. Mediante la comparación con los resultados obtenidos en los ensayos con morteros nuevos, usando dichos métodos y también los métodos recomendados por la norma europea, se sacan conclusiones sobre el potencial de los métodos.Por último, se establece una correlación entre los resultados experimentales y el nivel de deterioro inicial atribuido a los morteros antiguos mediante inspección visual.

  1. Closure Report for Corrective Action Unit 537: Waste Sites, Nevada Test Site, Nevada

    International Nuclear Information System (INIS)

    NSTec Environmental Restoration

    2007-01-01

    Corrective Action Unit (CAU) 537 is identified in the ''Federal Facility Agreement and Consent Order'' (FFACO) of 1996 as Waste Sites. CAU 537 is located in Areas 3 and 19 of the Nevada Test Site, approximately 65 miles northwest of Las Vegas, Nevada, and consists of the following two Corrective Action Sites (CASs): CAS 03-23-06, Bucket; Yellow Tagged Bags; and CAS 19-19-01, Trash Pit. CAU 537 closure activities were conducted in April 2007 according to the FFACO and Revision 3 of the Sectored Clean-up Work Plan for Housekeeping Category Waste Sites (U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office [NNSA/NSO], 2003). At CAS 03-23-06, closure activities included removal and disposal of a 15-foot (ft) by 15-ft by 8-ft tall wooden shed containing wood and metal debris and a 5-gallon plastic bucket containing deteriorated plastic bags with yellow radioactive contamination tape. The debris was transported to the Area 9 U10c Landfill for disposal after being screened for radiological contamination according to the ''NV/YMP Radiological Control Manual'' (NNSA/NSO, 2004). At CAS 19-19-01, closure activities included segregation, removal, and disposal of non-friable, non-regulated asbestos-containing material (ACM) and construction debris. The ACM was determined to be non-friable by waste characterization samples collected prior to closure activities. The ACM was removed and double-bagged by licensed, trained asbestos workers and transported to the Area 9 U10c Landfill for disposal. Construction debris was transported in end-dump trucks to the Area 9 U10c Landfill for disposal. Closure activities generated sanitary waste/construction debris and ACM. Waste generated during closure activities was appropriately managed and disposed. Waste characterization sample results are included as Appendix A of this report, and waste disposition documentation is included as Appendix B of this report. Copies of the Sectored Housekeeping Site Closure

  2. Evaluating the effect of lithology on porosity development in ridgetops in the Appalachian Piedmont

    Science.gov (United States)

    Marcon, V.; Gu, X.; Fisher, B.; Brantley, S. L.

    2016-12-01

    Together, chemical and physical processes transform fresh bedrock into friable weathered material. Even in systems where lithology, tectonic history, and climatic history are all known, it is challenging to predict the depth of weathering because the mechanisms that control the rate of regolith formation are not understood. In the Appalachian Piedmont, where rates of regolith formation and erosion are thought to be in a rough steady state, the depth of weathering varies with lithology. The Piedmont provides a controlled natural environment to isolate the effects of lithology on weathering processes so we can start to understand the mechanisms that initiate and drive weathering. Weathering is deepest over feldspathic rocks (schist/granite) with regolith 20-30m thick and thinnest over mafic and ultramafic rocks (diabase/serpentinite) with regolith serpentinization reactions and lost from collapse during weathering. Serpentinite consists of easily weathered hydrous minerals with little quartz. Comparatively, rocks with more quartz (e.g. schist) have a supportive skeleton as the rock weathers. This quartz skeleton could prevent the collapse of pores and result in isovolumetric weathering. Non-isovolumetric weathering limits infiltration of reactive fluids deeper into the rock, minimizing regolith formation in serpentinite due to its lack of a quartz skeleton. Given this, fracture toughness may be an important parameter to consider in terms of predicting regolith thickness.

  3. PECTIMORF and BIOBRAS-16 utilization in the potato somatic embryogenesis

    Directory of Open Access Journals (Sweden)

    Jaime R. Hidrobo Luna

    2002-01-01

    Full Text Available With the application of PECTIMORF and BIOBRAS-16, somatic embryos were obtained in potato (Solanum tuberosum, L c.v. Desirèe, of 40 days old callus obtained from stem micropropagated plants. These were used as possible substitutes for crop regulators used in culture media for the induction of somatic embryos. The culture media was composed for 10ml.l-1 of Murashige and Skoog salt, 0.1mg.l-1 ANA, 0.1mg.l-1 kinetin, 0.5mg.l-1 thiamine, 2.5mg.l-1 cistein, 100mg.l-1 mioinositol, 20g.l-1 sucrose and 2.0g.l-1 agar. Four culture medias were tested in distinct combinations that contained different concentration of PECTIMOR and BIOBRAS-16 as substitute of auxins and cytokinins. After 90 days, the results obtained showed the possibility of substituting the auxins (0.5mg.l-1 ANA and the cytokinins (0.5mg.l-1 kinetin in the culture media, because the application of PECTIMORF at 3.2mg.l-1 and BIOBRAS-16 at 1.0mg.l-1, gave friable callus, high fresh weight (more than 1.4g and a brownish color at the end of the process, moment in which the somatic embryos of different phases, appeared at the surface of the callus. Keywords: brasinoesteroids, callus, oligopectate, somatic embryo

  4. Pathological Effects of Aflatoxin and Their Amelioration by Vitamin E in White Leghorn Layers

    Directory of Open Access Journals (Sweden)

    Wajid A Khan, M Zargham Khan*, Ahrar Khan and Iftikhar Hussain1

    2010-07-01

    Full Text Available White Leghorn layer breeder hens, 30 weeks of age, were divided into 12 groups (A-L. Group A was kept on basal feed and served as control, while group B was offered feed supplemented with vitamin E (100 mg/Kg. Groups C-G were offered feed containing 100, 500, 2,500, 5,000 and 10,000 µg/Kg aflatoxin B1 (AFB1, respectively, whereas groups H-L were offered same dietary levels of AFB1 along with vitamin E (100 mg/Kg. The experimental feeds were offered for three weeks and afterward all the groups were switched over to basal feed for next two weeks. Body weight, absolute and relative weights of liver and kidneys of AF fed birds were significantly higher than control group. Pathological lesions in aflatoxin (AF fed birds included enlarged, pale and friable liver, swollen kidneys and hemorrhages on different organs. Histopathological lesions in liver included fatty change, congestion and hemorrhages, while in kidneys tubular necrosis, cellular infiltration, congestion and hemorrhages were found in groups fed AFB1 at 500 μg/Kg and higher doses. In AF fed hens, no significant ameliorative effects of vitamin E could be observed upon AF induced decrease in feed intake, gross pathology and histopathological alterations and organ weight except body weights. It was concluded that the vitamin E ameliorated the AFB1 induced toxic effects in some of parameters studied.

  5. Effect of x-ray irradiation on maize inbred line B73 tissue cultures and regenerated plants

    International Nuclear Information System (INIS)

    Wang, A.S.; Cheng, D.S.K.; Milcic, J.B.; Yang, T.C.

    1988-01-01

    In order to enhance variation induced by the tissue culture process and to obtain agronomically desirable mutants, friable embryogenic tissue cultures of maize (Zea mays L.) inbred line B73 were x-ray irradiated with 11 doses [0-8.4 kilorads (kR)]. Reductions in callus growth rate and embryogenic callus formation occurred with increasing x-ray doses 20 d and 3 months after irradiation. Callus irradiated with 0.8 kR showed a significant increase in growth rate and a 20% increase in embryogenic callus 9 months after irradiation. A total of 230 R 0 plants were regenerated for evaluation. Pollen fertility and seed set of R 0 plants decreased with increasing x-ray dosage. Days to anthesis and plant height of R 0 plants varied among x-ray treatments but were generally reduced with higher dosages. The number of chromosomal aberrations increased with x-ray dosage. The R 1 seeds taken from R 0 plants were also grown and tested for mutant segregation. Plants regenerated from irradiated calli had a two- to 10-fold increase in mutations over plants regenerated from unirradiated control callus. Germination frequency of seeds from R 0 plants decreased with increasing x-ray dosage. Although chlorophyll mutants were most frequently observed, a number of vigorous plants with earlier anthesis date were also recovered

  6. First interim examination of defected BWR and PWR rods tested in unlimited air at 2290C

    International Nuclear Information System (INIS)

    Einziger, R.E.; Cook, J.A.

    1983-01-01

    A five-year whole rod test was initiated to investigate the long-term stability of spent fuel rods under a variety of possible dry storage conditions. Both PWR and BWR rods were included in the test. The first interim examination was conducted after three months of testing to determine if there was any degradation in those defected rods stored in an unlimited air atmosphere. Visual observations, diametral measurements and radiographic smears were used to assess the degree of cladding deformation and particulate dispersal. The PWR rod showed no measurable change from the pre-test condition. The two original artificial defects had not changed in appearance and there was no diametral growth of the cladding. One of the defects in BWR rod showed significant deformation. There was approximately 10% cladding strain at the defect site and a small axial crack had formed. The fuel in the defect did not appear to be friable. The second defect showed no visible change and no cladding strain. Following examination, the test was continued at 230 0 C. Another interim examination is planned during the summer of 1983. This paper discusses the details and meaning of the data from the first interim examination

  7. Percutaneous suprapubic stone extraction for posterior urethral stones in children: efficacy and safety.

    Science.gov (United States)

    Safwat, Ahmed S; Hameed, Diaa A; Elgammal, Mohamed A; Abdelsalam, Yasser M; Abolyosr, Ahmad

    2013-08-01

    To evaluate the safety and efficacy of percutaneous suprapubic stone extraction (PSPSE) for pediatric posterior urethral stones. Between July 2007 and June 2010, 54 boys presenting with acute urinary retention due to posterior urethral stones underwent PSPSE. Patients were a mean age of 66.4 months (range, 8-180 months). The stone size was 0.7-1.9 cm. Patients were placed under general anesthesia, and a 7F urethroscope was used to pushback the stone to the bladder. A 3-mm suprapubic puncture with a scalpel was performed, followed by insertion of a straight narrow hemostat through the puncture aided with cystoscopic guidance. The stone was grasped with the hemostat in its narrowest diameter and was extracted percutaneously or crushed if friable. The suprapubic puncture was closed with a single 4-0 Vicryl (Ethicon) suture. Intact stone retrieval was achieved in 45 patients, and the stone was crushed into minute fragments in 9 patients. Intraperitoneal extravasation developed in 1 patient that required open surgical intervention. Mean operative time was 22 minutes. Patients were monitored for up to 17 months, with complete resolution of symptoms and stone clearance. PSPSE provides a minimally invasive approach for the extraction of urethral and bladder stones in the pediatric population. The use of a straight hemostat for suprapubic stone extraction or crushing is a good alternative to suprapubic tract dilation, with minimal morbidity. Copyright © 2013 Elsevier Inc. All rights reserved.

  8. Maritime and Underwater Cultural Heritage in South Africa: The Development of Relevant Management Strategies in the Historical Maritime Context of the Southern Tip of Africa

    Science.gov (United States)

    Sharfman, Jonathan; Boshoff, Jaco; Parthesius, Robert

    2012-10-01

    South Africans have a long association with water. It has provided a source of food, a medium for trade and a catalyst for migration and development. The country's geographical position as a crossroads of maritime trade between Europe and the East means that its history is inextricably linked to the history of the rest of the world. The result is a multi-faceted representation of sites, objects and mythologies related to water and maritime heritage that reflect not only local historical and social development, but global cultural change as well. Given the importance of South Africa's underwater cultural heritage (UCH), managers have grappled with management principles, ethics and theoretical models in an effort to produce and enforce heritage legislation that is relevant and effective. This paper outlines South Africa's maritime context from 1.5 million years ago until the present, summarises legislative and mitigation developments over the past half century and provides details of current trends in maritime archaeology and UCH management at the southern tip of Africa. Training programmes and public awareness are keys to this strategy to bring UCH and maritime archaeology into the mainstream and counter treasure hunting and looting of this rich, friable resource.

  9. Application of a Biodegradable Polyesteramide Derived from L-Alanine as Novel Excipient for Controlled Release Matrix Tablets.

    Science.gov (United States)

    Bonillo Martínez, Ana Dora; Galán, Inés Carmen Rodríguez; Bellver, María Victoria Margarit

    2017-11-01

    This pre-formulation study assays the capacity of the polyesteramide PADAS, poly (L-alanine-dodecanediol-L-alanine-sebacic), as an insoluble tablet excipient matrix for prolonged drug release. The flow properties of PADAS were suitable for tableting, and the compressibility of tablets containing exclusively PADAS was evaluated by ESEM observation of the microstructure. The tablets were resistant to crushing and non-friable and they did not undergo disintegration (typical features of an inert matrix). Tablets containing 33.33% sodium diclofenac (DF), ketoprofen (K) or dexketoprofen trometamol (DK-T) as a model drug, in addition with 66.67% of polymer, were formulated, and the absence of interactions between the components was confirmed by differential scanning calorimetry. Dissolution tests showed that PADAS retained DF and K and prolonged drug release, following a Higuchi kinetic. The tablets containing DK-T did not retain the drug sufficiently for prolonged release to be established. Tablets containing DK-T and 66.67, 83.33 or 91.67% PADAS, compressed at 44.48 or 88.96 kN, were elaborated to determine the influence of the polymer amount and of the compression force on DK-T release. Both parameters significantly delayed drug release, except when the proportion of polymer was 91.67%.

  10. Mixed Large Cell Neuroendocrine Carcinoma and Adenocarcinoma with Spindle Cell and Clear Cell Features in the Extrahepatic Bile Duct

    Directory of Open Access Journals (Sweden)

    John Wysocki

    2014-01-01

    Full Text Available Mixed adenoneuroendocrine carcinomas, spindle cell carcinomas, and clear cell carcinomas are all rare tumors in the biliary tract. We present the first case, to our knowledge, of an extrahepatic bile duct carcinoma composed of all three types. A 65-year-old man with prior cholecystectomy presented with painless jaundice, vomiting, and weight loss. CA19-9 and alpha-fetoprotein (AFP were elevated. Cholangioscopy revealed a friable mass extending from the middle of the common bile duct to the common hepatic duct. A bile duct excision was performed. Gross examination revealed a 3.6 cm intraluminal polypoid tumor. Microscopically, the tumor had foci of conventional adenocarcinoma (CK7-positive and CA19-9-postive surrounded by malignant-appearing spindle cells that were positive for cytokeratins and vimentin. Additionally, there were separate areas of large cell neuroendocrine carcinoma (LCNEC. Foci of clear cell carcinoma merged into both the LCNEC and the adenocarcinoma. Tumor invaded through the bile duct wall with extensive perineural and vascular invasion. Circumferential margins were positive. The patient’s poor performance status precluded adjuvant therapy and he died with recurrent and metastatic disease 5 months after surgery. This is consistent with the reported poor survival rates of biliary mixed adenoneuroendocrine carcinomas.

  11. Rhabdomyosarcoma associated with the lead wire of a pacemaker generator implant.

    Science.gov (United States)

    Thieman Mankin, Kelley M; Dunbar, Mark D; Toplon, David; Ginn, Pamela; Maisenbacher, Herbert W; Risselada, Marije

    2014-06-01

    An 11-year-old female spayed Labrador Retriever was presented for a draining, painful subcutaneous mass palpated over a previously implanted pacemaker generator. Infection was suspected and the mass was removed surgically. On cut surface, the mass was friable and mottled tan to brown with firm pale tan nodules, surrounding the pacemaker lead wire adjacent to the pacemaker generator. Cytologic interpretation of impression smears was consistent with a sarcoma, and suggestive of a rhabdomyosarcoma due to the presence of strap-like cells. On histopathologic examination, a highly invasive nodular mass surrounded the pacemaker lead, composed of pleomorphic round, spindle and strap cells, and multinucleated giant cells. The population exhibited microscopic invasion into the deep portion of the fibrous capsule surrounding the pacemaker generator. There were tumor emboli within small to medium subcutaneous veins adjacent to the mass. Immunohistochemically, the neoplastic cells stained positive for α-sarcomeric actin and vimentin, and negative for α-smooth muscle actin, consistent with a rhabdomyosarcoma arising at the site of the pacemaker generator. To our knowledge, this is the first report of a rhabdomyosarcoma associated with the lead wire of a pacemaker generator in a dog. © 2014 American Society for Veterinary Clinical Pathology and European Society for Veterinary Clinical Pathology.

  12. Lennox gastaut syndrome, review of the literature and a case report

    Directory of Open Access Journals (Sweden)

    Abu Saleh Tareq

    2008-06-01

    Full Text Available Abstract Background Lennox-Gastaut syndrome (LGS is a severe form of childhood epilepsy that is defined by generalized multiple type seizures, slowness of intellectual growth, and a specific EEG disturbance. Children affected might previously have infantile spasms or underlying brain disorder but etiology can be idiopathic. In South Africa, the incidence of secondary epilepsy is higher than what is found in developed countries resulting in higher incidence of the disease. LGS seizures are often treatment resistant and the long term prognosis is poor. Report A twenty six year old female, presented with anterior open bite, macroglossia, supragingival as well as subgingival calculus. The gingiva was red, swollen and friable and there was generalized bleeding and localized suppuration. The patient had gingival recession. After periodontal therapy a remarkable improvement in oral health status was noted. Conclusion The clinical findings in LGS included facial deformities, periodontitis and gingival swellings. Interdisciplinary treatment of these patients is fundamental and oral attention is of outstanding importance. Non-surgical periodontal therapy was effective in controlling periodontal disease in the reported case, but prevention of periodontal and dental diseases is preferable for this high-risk group of patients.

  13. Chemical composition of HAL, an isotopically-unusual Allende inclusion

    International Nuclear Information System (INIS)

    Davis, A.M.; Tanaka, T.; Grossman, L.; Lee, T.; Wasserburg, G.J.

    1982-01-01

    Thirty-seven major, minor and trace elements were determined by INAA and RNAA in samples of hibonite, black rim and portions of friable rim from an unusual Allende inclusion, HAL. The peculiar isotopic, mineralogical and textural properties of HAL are accompanied by very unusual trace element abundances. The most striking feature of the chemistry is the virtual absence of Ce from an inclusion otherwise highly enriched in REE compared to C1 chondrites. HAL is also depleted in Sr, Ba, U, V, Ru, Os and Ir, relative to other refractory elements. Of the lithophile elements determined which are normally considered to be refractory in a gas of solar composition, Sr, Ba, Ce, U and V are the most volatile in oxidizing gases. The distribution of REE between hibonite and rims seems to have been established when hibonite and other refractory minerals were removed at slightly different temperatures from a hot, oxidizing gas in which they previously coexisted as separate grains. On the basis of HAL's chemical and isotopic composition, possible locations for the chemical and mass dependent isotopic fractionation are discussed. (author)

  14. Vascular type Ehlers-Danlos syndrome is associated with platelet dysfunction and low vitamin D serum concentration.

    Science.gov (United States)

    Busch, Albert; Hoffjan, Sabine; Bergmann, Frauke; Hartung, Birgit; Jung, Helena; Hanel, Daniela; Tzschach, Andeas; Kadar, Janos; von Kodolitsch, Yskert; Germer, Christoph-Thomas; Trobisch, Heiner; Strasser, Erwin; Wildenauer, René

    2016-08-03

    The vascular type represents a very rare, yet the clinically most fatal entity of Ehlers-Danlos syndrome (EDS). Patients are often admitted due to arterial bleedings and the friable tissue and the altered coagulation contribute to the challenge in treatment strategies. Until now there is little information about clotting characteristics that might influence hemostasis decisively and eventually worsen emergency situations. 22 vascular type EDS patients were studied for hemoglobin, platelet volume and count, Quick and activated partial thromboplastin time, fibrinogen, factor XIII, von Willebrand disease, vitamin D and platelet aggregation by modern standard laboratory methods. Results show a high prevalence of over 50 % for platelet aggregation disorders in vascular type EDS patients, especially for collagen and epinephrine induced tests, whereas the plasmatic cascade did not show any alterations. Additionally, more than half of the tested subjects showed low vitamin D serum levels, which might additionally affect vascular wall integrity. The presented data underline the importance of detailed laboratory screening methods in vascular type EDS patients in order to allow for targeted application of platelet-interacting substances that might be of decisive benefit in the emergency setting.

  15. Geologic investigations of drill hole sloughing problems, Nevada Test Site

    International Nuclear Information System (INIS)

    Drellack, S.L. Jr.; Davies, W.J.; Gonzales, J.L.; Hawkins, W.L.

    1983-01-01

    Severe sloughing zones encountered while drilling large diameter emplacement holes in Yucca Flat, Nevada Test Site, have been identified, correlated and predicted through detailed geologic investigations. In central and southeastern Area 7 and in northern Area 3, the unstable zones are a very fine-grained, well-sorted, unconsolidated sand deposit, probably eolian in origin, which will readily flow into large diameter drill holes. Other areas exhibit hole erosion related to poor induration or extensive zeolitization of the Tertiary tuff units which are very friable and porous. By examining drill hole samples, geophysical logs, caliper logs and drilling histories, these problem zones can be characterized, correlated and then projected into nearby sites. Maps have been generated to show the depth, thickness and areal extent of these strata. In some cases, they are local and have a lenticular geometry, while in others they are quite extensive. The ability to predict such features can enhance the quality of the hole construction and completion operations to avoid costly delays and the loss of valuable testing real estate. The control of hole enlargements will also eliminate related containment concerns, such as stemming uncertainties

  16. The combination effect of auxin and cytokinin on in vitro callus formation of Physalis angulata L. - A medicinal plant

    Science.gov (United States)

    Mastuti, Retno; Munawarti, Aminatun; Firdiana, Elok Rifqi

    2017-11-01

    Physalis angulata L. (Ciplukan) is one member of Solanaceae that has a potential as herbal medicine. This plant grows wild in the crop fields, forest edges, etc. However, ciplukan is increasingly difficult to find recently. In vitro callus is an alternative source to produce secondary metabolite production as well as to regenerate plants through indirect organogenesis. This study aims to identify the response of hypocotyl explants on in vitro callus formation induced by a combination of auxin and cytokinins. Two types of cytokinins, Kinetin and BAP (0.5 ppm) were combined with three types of auxin, i.e. 2.4-D, IBA and IAA, at three concentrations 0.5, 1.0 and 1.5 ppm. In all combinations of cytokinin and auxin, 50-100% of hypocotyl explants derived from in vitro seedling were able to produce callus either in a compact or watery friable texture. In MS medium supplemented with 2.4-D, callus FW (fresh weight) began to decline in the fourth week after culture. Callus FW that increased until 5 weeks of culture was obtained in medium IAA 0.5 + Kin 0.5, IBA 1.0 + Kin 0.5 and IBA 1 + BA 0.5. Almost all calli induced on a medium + Kinetin also produced roots. While medium + BAP was able to induce shoots regeneration.

  17. Hot Leg Piping Materials Issues

    International Nuclear Information System (INIS)

    V. Munne

    2006-01-01

    With Naval Reactors (NR) approval of the Naval Reactors Prime Contractor Team (NRPCT) recommendation to develop a gas cooled reactor directly coupled to a Brayton power conversion system as the space nuclear power plant (SNPP) for Project Prometheus (References a and b) the reactor outlet piping was recognized to require a design that utilizes internal insulation (Reference c). The initial pipe design suggested ceramic fiber blanket as the insulation material based on requirements associated with service temperature capability within the expected range, very low thermal conductivity, and low density. Nevertheless, it was not considered to be well suited for internal insulation use because its very high surface area and proclivity for holding adsorbed gases, especially water, would make outgassing a source of contaminant gases in the He-Xe working fluid. Additionally, ceramic fiber blanket insulating materials become very friable after relatively short service periods at working temperatures and small pieces of fiber could be dislodged and contaminate the system. Consequently, alternative insulation materials were sought that would have comparable thermal properties and density but superior structural integrity and greatly reduced outgassing. This letter provides technical information regarding insulation and materials issues for the Hot Leg Piping preconceptual design developed for the Project Prometheus space nuclear power plant (SNPP)

  18. Using leptospermum honey to manage wounds impaired by radiotherapy: a case series.

    Science.gov (United States)

    Robson, Val; Cooper, Rose

    2009-01-01

    Radiation-induced tissue injury and wounds with radiation-impaired healing are traumatic for patients and challenging for their caregivers. Standardized management approaches do not exist. The effect of Leptospermum honey as a primary dressing for managing these wounds was assessed in four patients (age range 63 to 93 years) who had previously undergone radiotherapy that left them with fragile friable areas of damaged skin that did not respond to conventional treatment. Compromised areas involved the neck, cheek, groin/perineum, and chest. In patients 1 and 2, after topical application of honey via hydrofiber rope and nonadhesive foam, respectively, improvements in the size and condition of wound/periwound area and a reduction in pain were noted before death or loss to follow-up. After including honey in the treatment regimen of patients 3 and 4, complete healing was noted in 2.5 weeks (with honey and paraffin) and 6 weeks (with honey-soaked hydrofiber rope), respectively. No adverse events were reported. Honey as an adjunct to conventional wound/skin care post radiation therapy shows promise for less painful healing in these chronic wounds. Prospective, randomized, controlled clinical studies are needed to confirm these observations.

  19. COFIRING BIOMASS WITH LIGNITE COAL; FINAL

    International Nuclear Information System (INIS)

    Darren D. Schmidt

    2002-01-01

    The University of North Dakota Energy and Environmental Research Center, in support of the U.S. Department of Energy's (DOE) biomass cofiring program, completed a Phase 1 feasibility study investigating aspects of cofiring lignite coal with biomass relative to utility-scale systems, specifically focusing on a small stoker system located at the North Dakota State Penitentiary (NDSP) in Bismarck, North Dakota. A complete biomass resource assessment was completed, the stoker was redesigned to accept biomass, fuel characterization and fireside modeling tests were performed, and an engineering economic analysis was completed. In general, municipal wood residue was found to be the most viable fuel choice, and the modeling showed that fireside problems would be minimal. Experimental ash deposits from firing 50% biomass were found to be weaker and more friable compared to baseline lignite coal. Experimental sulfur and NO(sub x) emissions were reduced by up to 46%. The direct costs savings to NDSP, from cogeneration and fuel saving, results in a 15- to 20-year payback on a$1,680,000 investment, while the total benefits to the greater community would include reduced landfill burden, alleviation of fees for disposal by local businesses, and additional jobs created both for the stoker system as well as from the savings spread throughout the community

  20. The Effects of Cooking Process and Meat Inclusion on Pet Food Flavor and Texture Characteristics.

    Science.gov (United States)

    Koppel, Kadri; Gibson, Michael; Alavi, Sajid; Aldrich, Greg

    2014-05-23

    The pet food industry is an important portion of the food and feed industries in the US. The objectives of this study were (1) to determine cooking method (baking or extrusion), meat inclusion (0 or 20%), and extrusion thermal to mechanical energy ratios (low, medium, and high) effects on sensory and volatile properties of pet foods, and (2) to determine associations among sensory and volatile characteristics of baked and extruded pet foods. Descriptive sensory analysis and gas chromatography-mass spectrometry were used to analyze the pet food samples. It was found that baked samples were lighter in color (2.0-2.6 baked vs. 3.5-4.3 extruded, color intensity scale 0-15), and had lower levels of attributes that indicated rancidity (i.e., fishy flavor; 0.3-0.6 baked, 0.6-1.5 extruded, scale 0-15), whereas extruded pet foods were more cohesive in mass, more friable, hard, and crisp, but less powdery than baked samples. Fresh meat inclusion tended to decrease bitterness and increase fishy flavor and cohesiveness of pet foods. High thermal to mechanical energy ratio during extrusion resulted in less musty and more porous kibbles. The main volatile compounds included aldehydes, such as hexanal and heptanal, ketones, and alcohols. Extruded samples did not contain methylpyrazine, while baked samples did not contain 2-butyl furan. Future studies should consider evaluating the relationship between sensory results and animal palatability for these types of foods.

  1. Chronic copper toxicosis in sheep following the use of copper sulfate as a fungicide on fruit trees.

    Science.gov (United States)

    Oruc, Hasan H; Cengiz, Murat; Beskaya, Atilla

    2009-07-01

    Between January and October 2006, 15 Chios sheep died in a field located near a factory in Orhangazi, Bursa, Turkey. In addition, in May 2007, 2 ewes died after aborting in the same field. Clinical signs in affected animals prior to death were anorexia, hematuria, icterus, incoordination, and ptyalism. Postmortem findings included generalized icterus; yellow, friable livers; distended gallbladders with dense, dark bile; and dark, hypertrophic kidneys with hemorrhage. Copper (Cu) concentrations were measured in multiple specimens of the following: 9 sera, 3 livers, 3 kidneys, 4 plants (including 2 artichoke leaf specimens), 3 soil samples, and 1 drinking water sample. High Cu concentrations were present in the livers, kidneys, and sera of dead sheep, as well as in the vegetation and soil samples from the field. Chronic Cu toxicosis was confirmed as the cause of death attributed primarily to the use of copper sulfate as a fungicide for fruit trees within the field. In addition, factory dust containing Cu might have been an additional factor in the toxicosis.

  2. Acid-curing and ferric-trickle leaching effluent used in closed circuit uranium extractive process

    International Nuclear Information System (INIS)

    Jin Suoqing; Xiang Qinfang; Guo Jianzheng; Lu Guizhu; Su Yanru

    1998-01-01

    The new uranium ore process consists of crushing ore, mixing crushed ore with strong acid in rotating drums and curing the mixture in piles, trickle-leaching the ore beds with ferric solution, extracting uranium from pregnant solution with tertiary amine, precipitating product and disposing residue tailings. All the process effluent is used in closed circuit. There will be no process water to be discharged in the flowsheet except the tailings carrying off 15% water because during leaching moisture content of the ore rises to 15%. Tailings produced by the process are moist and friable, and can be disposed of on a pile or returned to the mine. Main technical parameters of the process: (a) water consumption is 0.2∼0.3 m 3 /t ore, electric power consumption is 20∼30 kW·h/t ore; (b) ore crushing up to -5∼-7 mm, leaching period is 12∼45 d, U content of residue is 0.01%∼0.02%, producing pregnant solution is 0.3∼0.5 m 3 /t ore, which is 1/5∼1/8 that of conventional agitation leaching process; (c) organic agent consumption is 1/5∼1/8 that of the conventional agitation process. All the research results above are tested by the pilot-plant test and industrial test. The new process has been applied to recovery of uranium in the mine located at northeast of China

  3. Production of high purity granular metals: cadmium, zinc, lead

    Directory of Open Access Journals (Sweden)

    Shcherban A. P.

    2017-04-01

    Full Text Available Cadmium, zinc and lead are constituent components of many semiconductor compounds. The obtained high purity distillates and ingots are large-size elements, which is not always convenient to use, and thus require additional grinding, which does not always allow maintaining the purity of the original materials. For the growth of semiconductor and scintillation single crystals it is advisable to use "friable" granular high-purity distillates, which can be processed without the risk of contamination. For example, the European low-background experiment LUCIFER required more than 20 kg of high-purity granulated zinc, which was agreed to be supplied by NSC KIPT. This task was then extended to cadmium and lead. Motivated by these tasks, the authors of this paper propose complex processes of deep refining of cadmium, zinc and lead by vacuum distillation. A device producing granules has been developed. The process of granulation of high-purity metals is explored. The purity of produced granules for cadmium and zinc is >99,9999, and >99,9995% for lead granules. To prevent oxidation of metal granules during exposition to air, chemical methods of surface passivation were used. Organic solvent based on dimethylformamide used as a coolant improves the resistance of granules to atmospheric corrosion during the granulation of high purity Cd, Zn and Pb.

  4. Somatic embryogenesis, scanning electron microscopy, histology and biochemical analysis at different developing stages of embryogenesis in six date palm (Phoenix dactylifera L.) cultivars.

    Science.gov (United States)

    Aslam, Junaid; Khan, Saeed Ahmad; Cheruth, Abdul Jaleel; Mujib, Abdul; Sharma, Maheshwar Pershad; Srivastava, Prem Shanker

    2011-10-01

    An efficient somatic embryogenesis system has been established in six date palm (Phoenix dactylifera L.) cultivars (Barhee, Zardai, Khalasah, Muzati, Shishi and Zart). Somatic embryogenesis (SE) was growth regulators and cultivars dependent. Friable embryogenic callus was induced from excised shoot tips on MS medium supplemented with various auxins particularly 2,4-dichlorophenoxyacetic acid (2,4-D, 1.5 mg 1(-l)). Suspension culture increased embryogenesis potentiality. Only a-naphthaleneacetic acid (NAA, 0.5 mg 1(-1)) produced somatic embryos in culture. Somatic embryos germinated and converted into plantlets in N(6)-benzyladenine (BAP, 0.75 mg 1(-l)) added medium following a treatment with thidiazuron (TDZ, 1.0 mg 1(-l)) for maturation. Scanning electron microscopy showed early stages of somatic embryo particularly, globular types, and was in masses. Different developing stages of embryogenesis (heart, torpedo and cotyledonary) were observed under histological preparation of embryogenic callus. Biochemical screening at various stages of somatic embryogenesis (embryogenic callus, somatic embryos, matured, germinated embryos and converted plantlets) of date palm cultivars has been conducted and discussed in detail. The result discussed in this paper indicates that somatic embryos were produced in numbers and converted plantlets can be used as a good source of alternative propagation. Genetic modification to the embryo precursor cell may improve the fruit quality and yield further.

  5. Somatic embryogenesis in cassava: A tool for mutation breeding

    International Nuclear Information System (INIS)

    Lee, K.S.; Duren, M. Van; Morpurgo, R.

    1997-01-01

    Cassava is an important food and livestock feed crop. The effect of gamma radiation on somatic embryogenesis and plant regeneration in cassava clones of African origin was investigated. Explants from young leaves of cassava were cultured on MS medium, supplemented with 18.1 mM 2,4-D and 2 mM CuSO4, solidified with 0.3% Phytagel. Compact and friable calli were observed after 10-15 days of explant culture in dark, which produced somatic embryos in all but one clone. The somatic embryos showed morphological aberrations, such as fused cotyledons, lack of meristematic tip, epicotyl elongation, and had low germination rate; desiccation of embryos increased germination. Histological study showed that the somatic embryos were of multicellular origin. Leaf explants were irradiated with doses between 4 to 38 Gy of gamma rays, and cultured on somatic embryo induction medium. In addition, somatic embryos were irradiated with gamma ray doses from 10 to 18 Gy, and analyzed for germination. LD 50 for embryogenic response of leaf-explants was at around 20 Gy, while that for somatic embryo germination was ca. 10 Gy. (author). 7 refs, 2 tabs

  6. Effect of Different Disinfection Protocols on Microbial and Biofilm Contamination of Dental Unit Waterlines in Community Dental Practices

    Directory of Open Access Journals (Sweden)

    Laura Dallolio

    2014-02-01

    Full Text Available Output water from dental unit waterlines (DUWLs may be a potential source of infection for both dental healthcare staff and patients. This study compared the efficacy of different disinfection methods with regard to the water quality and the presence of biofilm in DUWLs. Five dental units operating in a public dental health care setting were selected. The control dental unit had no disinfection system; two were disinfected intermittently with peracetic acid/hydrogen peroxide 0.26% and two underwent continuous disinfection with hydrogen peroxide/silver ions (0.02% and stabilized chlorine dioxide (0.22%, respectively. After three months of applying the disinfection protocols, continuous disinfection systems were more effective than intermittent systems in reducing the microbial contamination of the water, allowing compliance with the CDC guidelines and the European Council regulatory thresholds for drinking water. P. aeruginosa, Legionella spp, sulphite-reducing Clostridium spores, S. aureus and β-haemolytic streptococci were also absent from units treated with continuous disinfection. The biofilm covering the DUWLs was more extensive, thicker and more friable in the intermittent disinfection dental units than in those with continuous disinfection. Overall, the findings showed that the products used for continuous disinfection of dental unit waterlines showed statistically better results than the intermittent treatment products under the study conditions.

  7. Effect of different disinfection protocols on microbial and biofilm contamination of dental unit waterlines in community dental practices.

    Science.gov (United States)

    Dallolio, Laura; Scuderi, Amalia; Rini, Maria S; Valente, Sabrina; Farruggia, Patrizia; Sabattini, Maria A Bucci; Pasquinelli, Gianandrea; Acacci, Anna; Roncarati, Greta; Leoni, Erica

    2014-02-18

    Output water from dental unit waterlines (DUWLs) may be a potential source of infection for both dental healthcare staff and patients. This study compared the efficacy of different disinfection methods with regard to the water quality and the presence of biofilm in DUWLs. Five dental units operating in a public dental health care setting were selected. The control dental unit had no disinfection system; two were disinfected intermittently with peracetic acid/hydrogen peroxide 0.26% and two underwent continuous disinfection with hydrogen peroxide/silver ions (0.02%) and stabilized chlorine dioxide (0.22%), respectively. After three months of applying the disinfection protocols, continuous disinfection systems were more effective than intermittent systems in reducing the microbial contamination of the water, allowing compliance with the CDC guidelines and the European Council regulatory thresholds for drinking water. P. aeruginosa, Legionella spp, sulphite-reducing Clostridium spores, S. aureus and β-haemolytic streptococci were also absent from units treated with continuous disinfection. The biofilm covering the DUWLs was more extensive, thicker and more friable in the intermittent disinfection dental units than in those with continuous disinfection. Overall, the findings showed that the products used for continuous disinfection of dental unit waterlines showed statistically better results than the intermittent treatment products under the study conditions.

  8. Laparoscopic appendicectomy using endo-ring applicator and fallope rings

    International Nuclear Information System (INIS)

    Ali, Iyoob V; Maliekkal, Joji I

    2009-01-01

    Wider adoption of laparoscopic appendicectomy (LA) is limited by problems in securing the appendiceal base as well as the cost and the duration compared with the open procedure. The objective of this study was to assess the feasibility and efficacy of a new method for securing the appendiceal base in LA, so as to make the entire procedure simpler and cheaper, and hence, more popular. Twenty-five patients who were candidates for appendicectomy (emergency as well as elective) and willing for the laparoscopic procedure were selected for this study. Ports used were 10 mm at the umbilicus, 5 mm at the lower right iliac fossa, and 10 mm at the left iliac fossa. Extremely friable, ruptured, or turgid organs of diameters larger than 8 mm were excluded from the study. The mesoappendix was divided close to the appendix by diathermy. Fallope rings were applied to the appendiceal base using a special ring applicator, and the appendix was divided and extracted through the lumen of the applicator. The procedure was successful in 23 (92%) cases, and the mean duration of the procedure was 20 minutes (15-32 minutes). There were no procedural complications seen during a median follow-up of two weeks. The equipment and rings were cheaper when compared with that of the standard methods of securing the base of the appendix. LA using fallope rings is a safe, simple, easy-to-learn, and economically viable method. (author)

  9. Isolation and culture of Celosia cristata L cell suspension protoplasts

    Directory of Open Access Journals (Sweden)

    Retno Mastuti

    2003-06-01

    Full Text Available Developmental competence of Celosia cristata L. cell suspension-derived protoplasts was investigated. The protoplasts were isolatedfrom 3- to 9-d old cultures in enzyme solution containing 2% (w/v Cellulase YC and 0.5% (w/v Macerozyme R-10 which was dissolvedin washing solution (0.4 M mannitol and 10 mM CaCl2 at pH 5.6 for 3 hours. The highest number of viable protoplasts was releasedfrom 5-d old culture of a homogenous cell suspension. Subsequently, three kinds of protoplast culture media were simultaneously examinedwith four kinds of concentration of gelling agent. Culturing the protoplasts on KM8p medium solidified with 1.2% agarose significantlyenhanced plating efficiency as well as microcolony formation. Afterwards, the microcalli actively proliferated into friable watery calluswhen they were subcultured on MS medium supplemented with 0.3 mg/l 2,4-D and 1.0 mg/l kinetin. Although the plant regenerationfrom the protoplasts-derived calli has not yet been obtained, the reproducible developmental step from protoplasts to callus in thisstudy may facilitate the establishment of somatic hybridization using C. cristata as one parent.

  10. PIXE characterization of by-products resulting from the zinc recycling of industrial cemented carbides

    International Nuclear Information System (INIS)

    Freemantle, C.S.; Sacks, N.; Topic, M.; Pineda-Vargas, C.A.

    2015-01-01

    By-product materials of the widely used zinc recycling process of cemented carbides have been studied. Scanning electron microscopy and micro-PIXE techniques have identified elemental concentrations, distributions and purity of by-product materials from an industrial zinc recycling plant. Cobalt surface enrichment, lamellar microstructures of varying composition, including alternating tungsten carbide (WC) grains and globular cobalt, and regions of excess zinc contamination were found in materials with incomplete zinc penetration. Liquid Co–Zn formation occurred above 72 wt.% Zn at the furnace temperature of 930 °C, and was extracted towards the surface of poorly zinc infiltrated material, primarily by the vacuum used for zinc distillation. Surface enrichment was not observed in material that was zinc infiltrated to the sample center, which was more friable and exhibited more homogeneous porosity and elemental concentrations. The result of incomplete zinc infiltration was an enriched surface zone of up to 60 wt.% Co, compared to an original sample composition of ∼10–15 wt.% Co. The impact on resulting powders could be higher or inhomogeneous cobalt content, as well as unacceptably high zinc concentrations. PIXE has proven it can be a powerful technique for solving industrial problems in the cemented carbide cutting tool industry, by identifying trace elements and their locations (such as Zn to 0.1 wt.% accuracy), as well as the distribution of major elements within WC–Co materials.

  11. Chester (Mississippian) ostracodes from Bangor Formation of Black Warrior basin, northern Alabama

    Energy Technology Data Exchange (ETDEWEB)

    Devery, H.; Dewey, C.

    1986-05-01

    A previously unreported ostracode fauna is described from the Bangor Limestone in Franklin, Lawrence, and Colbert Counties, Alabama. The Bangor formation is a Chesterian (Mississippian) platformal carbonate sequence. The predominant carbonates are bioclastic and oolitic grainstones to wackestones with less abundant micritic claystones. Intercalated fine clastics are common in the upper and lower parts of the sequence. This study focuses on the bioclastic limestones with interbedded shales of the lower Bangor. The megafaunal associations include crinoid and blastoid pelmatozoans, orthotetid, and spiriferid brachiopids, and both fenestrate and nonfenestrate bryozoans. Solitary rugose corals and trilobites may be locally abundant. Gastropods and bivalves form a consistent but accessory part of the fauna, which indicates a shallow, nearshore shelf environment. A diverse ostracode fauna of variable abundance has been collected from the shaly units and friable limestones. The ostracode fauna indicates shallow, open-marine conditions and is dominated by bairdiaceans, including Bairdia spp. Rectobairdia and Bairdiacypris. Several species of Cavellina, healdia, and Seminolites are also abundant. Palaeocopids present include Coryellina, Kirkbya, and Polytylites. Kloedenellaceans include Beyrichiopsis, Glyptopleura, Glypotpleurina, and .Hypotetragona. Paraparchitaceans are notably more scarce, but specimens of Shishaella have been found. Some sample have a high valve to carapace ratio, suggesting postmortem transport. Although diversity is high, numerical abundances can be low. Initial studies suggest the ostracodes have a Mid-Continent affinity, which may indicate that the Appalachians were acting as a barrier to migration of European forms.

  12. Cardiac papillary fibroelastoma; when, how, why?

    Directory of Open Access Journals (Sweden)

    Nikolaos G Baikoussis

    2016-01-01

    Full Text Available We would like to present an interesting case operated on in our department and discuss the international bibliography about this issue. We also present some interesting images of this case. Our material is composed from a 68-year-old woman treated by the authors. She presented with a small murmur in the auscultation while she was asymptomatic and then she diagnosed with a tumor on of the left coronary cusp of the aortic valve with the characteristics of papillary fibroelastoma. On the basis of the potential embolic risk either of the mass itself or of associated thrombus and the possibility of further enlargement, the patient although asymptomatic at the time of diagnosis was referred for elective surgical excision of the mass. She underwent on median sternotomy and through extracorporeal circulation the mass has been excised with the preservation of the well-functioning valve. Through this case, we would like to discuss the bibliography for the decision making in these cases. Hence, the aim of our study is that we have to keep in mind that this kind of friable mass may be the cause of embolism, stroke or coronary artery occlusion and must be excided in a conservative setting, sparing the aortic valve.

  13. Biochemical and pathological findings of pregnancy toxemia in Saanen doe: A case report

    Directory of Open Access Journals (Sweden)

    Yusuf Abba

    2015-06-01

    Full Text Available A pregnant Saanen doe aging 1.5-year and weighing 40 kg was presented to the Large Animal Unit of Universiti Putra Malaysia Veterinary Hospital with history of inability to stand up. Transabdominal ultrasonography of the animal revealed two live fetuses at late pregnancy. Blood examination revealed decreased lymphocyte numbers, and increased monocytes count. Biochemical analyses showed marked decrease in glucose level and elevated level of aspartate aminotransferase (AST and creatine kinase (CK. The goat was administered with 200 mL 20% Dextrose (G-20, NaCl solution (at 1.3 mL/animal, Flunixine meglumine (at 2.2 mg/kg bwt, and Vitavet multivitamin (at 1 mL/10 kg bwt. The prognosis of the case was grave, and the goat was sacrificed in order to save the fetuses. However, the fetuses were died within 10 min. Necropsy of the doe showed pale, yellow and friable liver and congested lungs, while histopathological evaluation of the liver showed diffuse hepatic lipidosis. Pregnancy toxemia in doe can be prevented by providing proper nutrition.

  14. Atypical primary meningioma in the nasal septum with malignant transformation and distant metastasis

    International Nuclear Information System (INIS)

    Baek, Byoung Joon; Shin, Jae–Min; Lee, Chi Kyou; Lee, Ji Hye; Lee, Koen Hyeong

    2012-01-01

    Primary extracranial meningiomas (PEMs) originating from the nasal septum are extremely rare, as are extracranial metastases of meningiomas. A 44-year-old male presented with a 2-month history of left-side nasal obstruction and frequent episodes of epistaxis. A friable mass originating from the nasal septum was resected completely via an endoscopic endonasal approach. According to WHO criteria, the tumor was diagnosed as an atypical meningioma radiologically and histopathologically. Two years later, a tumor recurred at the primary site with the same histopathological findings, and the patient was given local external radiotherapy (6840 cGy in 38 fractions). Two months after this local recurrence, a left anterior chest wall mass and a left parietal area scalp mass were observed. The subcutaneous mass was resected and showed histological evidence of malignant transformation. Several months after the last operation, the patient died. We describe the clinical, radiological, and bio-pathological features of this unique case and review the literature on atypical PEMs originating in the nasal septum. To our knowledge, this is the first reported case of an atypical PEM originating from the nasal septum that recurred with malignant transformation and extracranial metastasis

  15. PIXE characterization of by-products resulting from the zinc recycling of industrial cemented carbides

    Energy Technology Data Exchange (ETDEWEB)

    Freemantle, C.S. [School of Chemical & Metallurgical Engineering and DST-NRF Centre of Excellence in Strong Materials, University of the Witwatersrand, P/Bag 3, Wits 2050 (South Africa); Pilot Tools (Pty) (Ltd), P.O. Box 27420, Benrose 2011 (South Africa); Sacks, N. [School of Chemical & Metallurgical Engineering and DST-NRF Centre of Excellence in Strong Materials, University of the Witwatersrand, P/Bag 3, Wits 2050 (South Africa); Topic, M. [iThemba LABS, National Research Foundation, P.O. Box 722, Somerset West 7129 (South Africa); Pineda-Vargas, C.A. [iThemba LABS, National Research Foundation, P.O. Box 722, Somerset West 7129 (South Africa); Faculty of Health & Wellness Sciences, CPUT, Bellville (South Africa)

    2015-11-15

    By-product materials of the widely used zinc recycling process of cemented carbides have been studied. Scanning electron microscopy and micro-PIXE techniques have identified elemental concentrations, distributions and purity of by-product materials from an industrial zinc recycling plant. Cobalt surface enrichment, lamellar microstructures of varying composition, including alternating tungsten carbide (WC) grains and globular cobalt, and regions of excess zinc contamination were found in materials with incomplete zinc penetration. Liquid Co–Zn formation occurred above 72 wt.% Zn at the furnace temperature of 930 °C, and was extracted towards the surface of poorly zinc infiltrated material, primarily by the vacuum used for zinc distillation. Surface enrichment was not observed in material that was zinc infiltrated to the sample center, which was more friable and exhibited more homogeneous porosity and elemental concentrations. The result of incomplete zinc infiltration was an enriched surface zone of up to 60 wt.% Co, compared to an original sample composition of ∼10–15 wt.% Co. The impact on resulting powders could be higher or inhomogeneous cobalt content, as well as unacceptably high zinc concentrations. PIXE has proven it can be a powerful technique for solving industrial problems in the cemented carbide cutting tool industry, by identifying trace elements and their locations (such as Zn to 0.1 wt.% accuracy), as well as the distribution of major elements within WC–Co materials.

  16. Mixed metazoan and bacterial infection of the gas bladder of the lined seahorse-a case report.

    Science.gov (United States)

    Anderson, Paul A; Petty, Barbara D

    2013-03-01

    Five wild-caught Lined Seahorses Hippocampus erectus from an aquarium system presented with altered buoyancy and distended upper trunks. Radiography of one specimen revealed a reduced air volume in the gas bladder. Pneumocystocentesis revealed a brown exudate of numerous leukocytes, parasite ova, and Gram- and acid-fast-positive bacilli under wet mounts and stains. Necropsies revealed enlarged, friable kidneys and distended gas bladders containing copious purulent exudate, necrotic tissue, and adult digeneans Dictysarca virens. Bacterial isolates from exudate cultures grown on Lowenstein-Jensen medium were identified as Gordonia sp. and Mycobacterium poriferae by high-performance liquid chromatography and 16S ribosomal DNA sequencing. Histopathology demonstrated a histiocytic response in kidney and gas bladder exudate, inflammation of the gas bladder wall, and infection of the gas bladder lumen with parasite ova and acid-fast-positive and Gomori's methenamine silver-positive bacilli. Praziquantel is prescribed for digenean infections but dissolves incompletely in seawater and is toxic to this host. Eradication of intermediate host vectors is a management option. Treatment of Gordonia infection has not been addressed in nonhuman animals, and there is no known effective treatment for Mycobacterium spp. infection in fishes. This is the first case report of digenean infection of the gas bladder in a syngnathid, Gordonia sp. infection in a nonhuman animal, and M. poriferae infection in a fish.

  17. Strategies to Reduce Tin and Other Metals in Electronic Cigarette Aerosol.

    Directory of Open Access Journals (Sweden)

    Monique Williams

    Full Text Available Metals are present in electronic cigarette (EC fluid and aerosol and may present health risks to users.The objective of this study was to measure the amounts of tin, copper, zinc, silver, nickel and chromium in the aerosol from four brands of EC and to identify the sources of these metals by examining the elemental composition of the atomizer components.Four brands of popular EC were dissected and the cartomizers were examined microscopically. Elemental composition of cartomizer components was determined using integrated energy dispersive X-ray microanalysis, and the concentrations of the tin, copper, zinc silver, nickel, and chromium in the aerosol were determined for each brand using inductively coupled plasma optical emission spectroscopy.All filaments were made of nickel and chromium. Thick wires were copper coated with either tin or silver. Wires were joined to each other by tin solder, brazing, or by brass clamps. High concentrations of tin were detected in the aerosol when tin solder joints were friable. Tin coating on copper wires also contributed to tin in the aerosol.Tin concentrations in EC aerosols varied both within and between brands. Tin in aerosol was reduced by coating the thick wire with silver rather than tin, placing stable tin solder joints outside the atomizing chamber, joining wires with brass clamps or by brazing rather than soldering wires. These data demonstrate the feasibility of removing tin and other unwanted metals from EC aerosol by altering designs and using materials of suitable quality.

  18. High temperature corrosion of nickel alloys by molten calcium chloride in an oxidising environment

    International Nuclear Information System (INIS)

    Barnett, Roger; Gittos, Mike

    2012-09-01

    A series of nickel alloys was submerged in molten calcium chloride (a molten salt proposed for and used in the nuclear industry for a variety of applications), at 850 deg. C for 72 hours under an oxidising environment. The samples were analysed in detail, in order to determine their corrosion behaviour and suitability for use under these conditions. 310 stainless steel was used as a reference material. Extensive corrosion occurred and the observed attack on the metal substrates was general and massive with corrosion rates ranging from 1.17 mm/year, for Haynes 214, to 13.3 mm/year, for 310 stainless steel. All materials showed selective leaching of chromium from the samples but the oxide layer formed was not protective, spalling away easily. The severity of the attack was not immediately visible from the corrosion rate alone: samples showed a friable scale on the surface and deep penetration of the attack beneath, up to 0.63 mm for 310 stainless steel. In some cases, the attack was clearly intergranular with chromium being depleted along the grain boundaries, whereas in others, the attack was more general. No simple correlation between alloying elements and corrosion rate was apparent, with additions of aluminium and silicon appearing to have little or no protective effect. Alloys 600 and Haynes HR-160 showed promise, with relatively low corrosion rates and penetration depths. (authors)

  19. Somatic embryogenesis in cassava: A tool for mutation breeding

    Energy Technology Data Exchange (ETDEWEB)

    Lee, K S; Duren, M Van; Morpurgo, R [Agriculture and Biotechnology Laboratory, International Atomic Energy Agency, Seibersdorf (Austria)

    1997-07-01

    Cassava is an important food and livestock feed crop. The effect of gamma radiation on somatic embryogenesis and plant regeneration in cassava clones of African origin was investigated. Explants from young leaves of cassava were cultured on MS medium, supplemented with 18.1 mM 2,4-D and 2 mM CuSO4, solidified with 0.3% Phytagel. Compact and friable calli were observed after 10-15 days of explant culture in dark, which produced somatic embryos in all but one clone. The somatic embryos showed morphological aberrations, such as fused cotyledons, lack of meristematic tip, epicotyl elongation, and had low germination rate; desiccation of embryos increased germination. Histological study showed that the somatic embryos were of multicellular origin. Leaf explants were irradiated with doses between 4 to 38 Gy of gamma rays, and cultured on somatic embryo induction medium. In addition, somatic embryos were irradiated with gamma ray doses from 10 to 18 Gy, and analyzed for germination. LD{sub 50} for embryogenic response of leaf-explants was at around 20 Gy, while that for somatic embryo germination was ca. 10 Gy. (author). 7 refs, 2 tabs.

  20. Abdominal wall sinus due to impacting gallstone during laparoscopic cholecystectomy: an unusual complication.

    Science.gov (United States)

    Pavlidis, T E; Papaziogas, B T; Koutelidakis, I M; Papaziogas, T B

    2002-02-01

    During laparoscopic cholecystectomy, perforation of the gallbladder can occurs in extraction of the gallbladder. The fate of such lost gallstones, which can lead to the formation of an abscess, an abdominal wall mass, or a persistent sinus, has not been studied adequately. Herein we report the case of a persistent sinus of the abdominal wall after an emergent laparoscopic cholecystectomy in an 82-year-old woman with gangrenous cholecystitis and perforation of the friable wall in association with an empyema of the gallbladder. The culture of the obtained pus was positive for Escherichia coli. After a small leak of dirty fluid from the wound of the epigastric port site of 4 months' duration, surgical exploration under local anesthesia revealed that the sinus was caused by spilled gallstones impacting into the abdominal wall between the posterior sheath and left rectus abdominalis muscle. The removal of the stones resulted in complete healing. Long-term complications after laparoscopic cholecystectomy involving the abdominal wall are rare but important possible consequences that could be avoided.

  1. STUDY ON THE VALORIFICATION OF LYCIUM BARBARUM FRUIT (GOJI IN PASTRY PRODUCTS

    Directory of Open Access Journals (Sweden)

    Anamaria Pop

    2013-11-01

    Full Text Available The aim of this research refers to the development of new recipes of fabricating tow different muffins and spritz cookies, using Goji whole fruits rehydrated and Goji ground powder type fruits, in different proportions and after, by sensory analysis proving the consumer preferences in relation to Goji fruit intake in the products. Also has been studied the total carotenoid content by spectrophotometric measurements from finished products comparing with whole goji berry fruit. The products are obtained by baking dough made ​​from flour, sugar, eggs, vegetable fat, milk, goji berries, friable chemical. The raw material and auxiliary material (white flour and Goji berries and the pastry products obtain with addition of goji was submitted to the physio-chemical exam, following: moisture content, ash content, gluten content, acidity content, vitamin C content, carotenoids content in accordance with applicable standards. Therefore we obtained 3 types of muffins (simple muffins, muffins with addition of 10% whole goji fruit, muffins with addition of 10% fruit goji powder ground type and 4 types of spritz cookies (simple cookies, cookies with addition of 3 %, 5 %, 10 % of goji powder.

  2. Strategies to Reduce Tin and Other Metals in Electronic Cigarette Aerosol

    Science.gov (United States)

    Williams, Monique; To, An; Bozhilov, Krassimir; Talbot, Prue

    2015-01-01

    Background Metals are present in electronic cigarette (EC) fluid and aerosol and may present health risks to users. Objective The objective of this study was to measure the amounts of tin, copper, zinc, silver, nickel and chromium in the aerosol from four brands of EC and to identify the sources of these metals by examining the elemental composition of the atomizer components. Methods Four brands of popular EC were dissected and the cartomizers were examined microscopically. Elemental composition of cartomizer components was determined using integrated energy dispersive X-ray microanalysis, and the concentrations of the tin, copper, zinc silver, nickel, and chromium in the aerosol were determined for each brand using inductively coupled plasma optical emission spectroscopy. Results All filaments were made of nickel and chromium. Thick wires were copper coated with either tin or silver. Wires were joined to each other by tin solder, brazing, or by brass clamps. High concentrations of tin were detected in the aerosol when tin solder joints were friable. Tin coating on copper wires also contributed to tin in the aerosol. Conclusions Tin concentrations in EC aerosols varied both within and between brands. Tin in aerosol was reduced by coating the thick wire with silver rather than tin, placing stable tin solder joints outside the atomizing chamber, joining wires with brass clamps or by brazing rather than soldering wires. These data demonstrate the feasibility of removing tin and other unwanted metals from EC aerosol by altering designs and using materials of suitable quality. PMID:26406602

  3. COFIRING BIOMASS WITH LIGNITE COAL

    Energy Technology Data Exchange (ETDEWEB)

    Darren D. Schmidt

    2002-01-01

    The University of North Dakota Energy & Environmental Research Center, in support of the U.S. Department of Energy's (DOE) biomass cofiring program, completed a Phase 1 feasibility study investigating aspects of cofiring lignite coal with biomass relative to utility-scale systems, specifically focusing on a small stoker system located at the North Dakota State Penitentiary (NDSP) in Bismarck, North Dakota. A complete biomass resource assessment was completed, the stoker was redesigned to accept biomass, fuel characterization and fireside modeling tests were performed, and an engineering economic analysis was completed. In general, municipal wood residue was found to be the most viable fuel choice, and the modeling showed that fireside problems would be minimal. Experimental ash deposits from firing 50% biomass were found to be weaker and more friable compared to baseline lignite coal. Experimental sulfur and NO{sub x} emissions were reduced by up to 46%. The direct costs savings to NDSP, from cogeneration and fuel saving, results in a 15- to 20-year payback on a $1,680,000 investment, while the total benefits to the greater community would include reduced landfill burden, alleviation of fees for disposal by local businesses, and additional jobs created both for the stoker system as well as from the savings spread throughout the community.

  4. Nuclear graphite for high temperature reactors

    International Nuclear Information System (INIS)

    Marsden, B.J.

    2001-01-01

    The cores and reflectors in modern High Temperature Gas Cooled Reactors (HTRs) are constructed from graphite components. There are two main designs; the Pebble Bed design and the Prism design. In both of these designs the graphite not only acts as a moderator, but is also a major structural component that may provide channels for the fuel and coolant gas, channels for control and safety shut off devices and provide thermal and neutron shielding. In addition, graphite components may act as a heat sink or conduction path during reactor trips and transients. During reactor operation, many of the graphite component physical properties are significantly changed by irradiation. These changes lead to the generation of significant internal shrinkage stresses and thermal shut down stresses that could lead to component failure. In addition, if the graphite is irradiated to a very high irradiation dose, irradiation swelling can lead to a rapid reduction in modulus and strength, making the component friable.The irradiation behaviour of graphite is strongly dependent on its virgin microstructure, which is determined by the manufacturing route. Nevertheless, there are available, irradiation data on many obsolete graphites of known microstructures. There is also a well-developed physical understanding of the process of irradiation damage in graphite. This paper proposes a specification for graphite suitable for modern HTRs. (author)

  5. Contact angle measurements at the colemanite and realgar surfaces

    Science.gov (United States)

    Koca, Sabiha; Savas, Mehmet

    2004-03-01

    Colemanite is one of the most important boron minerals and covers an important part of Turkey's boron mineral deposits. The friable nature of the colemanite tends to produce a large amount of fines. Flotation appears to be a promising technique to recover colemanite from such fines. During flotation process, selectivity problem arises between colemanite and associated gangue minerals such as realgar. There is a close relationship between floatability of minerals and contact angle. Therefore, surface hydrophobicity of colemanite and realgar minerals were investigated by receding contact angle measurements in the absence and presence of flotation reagents. The water contact angle values at the colemanite surface remained almost unchanged at 32-35° in the solutions of potassium amyl xanthate (KAX), potassium ethyl xanthate (KEX) and petroleum sulphanate (R825) while another petroleum sulphanate (R840), sodium oleate and tallow amine (Armac-T) affected hydrophobicity of colemanite, and the contact angle values increased up to 47°. The contact angle values of 62, 63, 45, 46, 39, and 43° at the realgar surface were obtained in the solutions of KAX, KEX, sodium oleate, R825, R840 and Armac-T, respectively.

  6. Malignant mixed Mullerian tumour of the prolapsed cervix: A case report.

    Science.gov (United States)

    Massinde, Anthony N; Rumanyika, Richard R; Kihunrwa, Albert; Rambau, Peter; Magoma, Moke

    2012-04-01

    Malignant mixed Mullerian tumour is a rare gynaecological tumour commonly presenting with vaginal bleeding, abdominal pain or mass in the uterine cavity, cervix or vagina. The neoplasms are commonly seen in postmenopausal women although it has been observed in younger women. Ovaries and the corpus of the uterus are commonly involved, whereas involvement of the cervix and vagina is rare. A 37 year-old Tanzania lady para 7 with a previous history of two genital polypectomies presented with history of recurrent vaginal mass which was associated with abnormal vaginal bleeding and foul smelling discharge. Vaginal examination revealed a prolapsed uterus with giant fungating cervical mass which was ulcerated, friable, and bled easily on touch. Impression was grade three uterine prolapse with infected cervical polyp/cervical sarcoma. Excision of the tumour through trans-vaginal hysterectomy was performed, no lymphadenopathy was found, no adnexa abnormalities, and no involvement of the vaginal wall. Histological diagnosis of Malignant mixed Mullerian tumour of the cervix was made. Patient recovery was unremarkable; however she was lost to follow up. The patient's mass was initially suspected to be prolapsed uterus with decubitus ulcer but the histological results were of a malignant condition. Lack of clear management guidelines for some rare mixed tumours remains a challenge for clinicians in low resource settings.

  7. Kerathocyst odontogenic tumor: Importance of selection the best treatment modality and a periodical follow-up to prevent from recurrence: A case report and literature review

    Directory of Open Access Journals (Sweden)

    Nasim Jafaripozve

    2013-01-01

    Full Text Available The keratocystic odontogenic tumor (KCOT is a relatively common oral and maxillofacial lesion with specific characteristics such us rapid growth, extension into the surrounding tissues and high rates of recurrence. Various treatment modalities have been reported. Due to the very thin and friable lining characteristic of the tumor, enucleation can be difficult undertaken and for this reason it is associated with the highest recurrence rates. A 22-year-old male referred to our clinic due to a slight expansion in the right mandible from 2 years ago. He has a history of occurrence of KCOT in this region that was treated surgically by enucleation and curettage 5 years ago. Cone beam computed tomography showed a multilocular radiolucent lesion that extended from the angle of the mandible to the symphysis. Incisional biopsy showed a KCOT recurrence that surgically treated with resection of the right mandible by continuity preservation. Selection of the best treatment modality and also a periodical lifelong follow-up is very important to reduce the rate of recurrence and morbidity of the patient.

  8. Macedonian lignite - upgrading and evaluation

    International Nuclear Information System (INIS)

    Musich, Mark A.; Young, Brian C.

    1997-01-01

    Macedonian lignites have a high moisture content, low heating value, and are friable, generating fines and dust. Macedonia has an urgent need to use indigenous solid fuel resources for domestic and industrial heating as well as metallurgical applications. The goal of this project was to evaluate the potential for beneficiating Macedonian lignite and producing high-quality briquettes for metallurgical use as well as domestic/industrial heating. Laboratory studies have shown that treating the Macedonian lignite fines by two physical processes-cleaning and carbonization-followed by pelletizing. can generate acceptable lump fuels for heating applications. Carbonizing the float-sink-cleaned lignite to reduce the volatile matter content and pelletizing the resultant char with starch produced strong pellets, which could be used as a home-heating fuel, the char having a heat content of 13,400 Btu/lb (31.2 MJ/Kg). However, additional work is required at the pilot scale to determine optimum briquetting conditions and production costs. (Author)

  9. Large gangliocytic paraganglioma of the duodenum: A rare entity.

    Science.gov (United States)

    Hernández, Alejandra Gordillo; Lanuza, Eduardo Dominguez-Adame; Matias, Auxiliadora Cano; Huertas, Rosario Perez; Rodriguez, Katherine Maria Gallardo; Perez, Purificacion Gallinato; Mompean, Fernando Oliva

    2015-08-27

    Gangliocytic paragangliomas are rare tumors that almost exclusively occur within the second portion of the duodenum. Although these tumors generally have a benign clinical course, they have the potential to recur or metastasize to regional lymph nodes. The case report presented here describes a 57-year-old female patient with melena, progressive asthenia, anemia, and a mass in the second-third portion of the duodenum that was treated by local excision. The patient was diagnosed with a friable bleeding tumor. The histologic analysis showed that the tumor was a 4 cm gangliocytic paraganglioma without a malignant cell pattern. In the absence of local invasion or distant metastasis, endoscopic resection represents a feasible, curative therapy. Although endoscopic polypectomy is currently considered the treatment of choice, it is not recommended if the size of the tumor is > 3 cm and/or there is active or recent bleeding. Patients diagnosed with a gangliocytic paraganglioma should be closely followed-up for possible local recurrence.

  10. Influence of Growth Regulators on Callogenesis and Somatic Embryo Development in Date Palm (Phoenix dactylifera L. Sahelian Cultivars

    Directory of Open Access Journals (Sweden)

    Djibril Sané

    2012-01-01

    Full Text Available This study provides a physiological analysis of somatic embryogenesis in four elite cultivars of date palms: Ahmar, Amsekhsi, Tijib, and Amaside, from the initial callogenesis to establishment and proliferation of embryogenic suspension cultures. Somatic embryos development and in vitro plants rooting were also studied. For each step, auxins and cytokinins concentrations were optimised. The primary callogenesis from leaf explants of seedlings appeared highly dependent on genotype. Ahmar (80% and Amsekhsi (76% appeared highly callogenic, whereas Tijib (10% and Amaside (2% produced low amounts of calluses. 2,4-Dichlorophenoxyacetic acid appeared favorable to the induction of primary callogenesis and its effect was enhanced by the addition of benzyl adenine or adenine sulfate. Secondary friable calli obtained from chopped granular calli were used to initiate embryogenic cell suspensions in media supplied with 2,4-dichlorophenoxyacetic acid. Suspension cultures showed a growth rate of fourfold after four subcultures in presence of 2,4-dichlorophenoxyacetic acid 2 mg/L. Our results showed that a seven-day transitory treatment with benzyl adenine 0,5 mg/L was necessary to optimize embryos development. Naphthalene acetic acid induced the development of primary orthogravitropic roots during embryos germination. The comparison with cytofluorometry of nuclear DNA amounts showed no significant difference in ploidy level between regenerated plants and seedlings.

  11. Landslide Spatial Distribution Analysis Using GIS. Case Study Secașelor Plateau.

    Directory of Open Access Journals (Sweden)

    Gheorghe Rosian

    2017-05-01

    Full Text Available Landslides represent an extremely frequent geomorphological phenomenon in the Secașelor Plateau. The regional unit is located in the South-Eastern part of the Transylvanian Basin (large basin within the Carpathian Mountains. In this paper, we analyzed the distribution of the landslides through spatial statistics techniques and GIS. In order to analyze the distribution of the landslides we took into consideration 5 criteria: geology, height, slope, exposition and the territorial administrative units. This type of study is necessary to find out the way in which the actual landslides are distributed and on the other hand, the research will collect information on the susceptible fields which are favored by these geomorphological processes. After the visual analysis of the area using the 1:5000 aerial photography and topographic maps, 835 landslides were identified and vectorized. At the level of administrative-territorial units, these cover mostly agricultural areas. Given the lithological conditions (the presence of friable rocks of marl, clay and poorly cemented sands and the land use (mostly agricultural it can be said that in the future new landslides will ocure in similar conditions of slope, exposition and geological characteristic etc. The identification of areas that are susceptible to landslides is beneficial for the future territorial planning actions and also to avoid building on areas which are prone to landslides.

  12. Remote sensing data applied to the evaluation of soil erosion caused by land-use. Ribeirao Anhumas Basin Area: A case study. [Brazil

    Science.gov (United States)

    Dejesusparada, N. (Principal Investigator); Dosanjosferreirapinto, S.; Kux, H. J. H.

    1980-01-01

    Formerly covered by a tropical forest, the study area was deforested in the early 40's for coffee plantation and cattle raising, which caused intense gully erosion problems. To develop a method to analyze the relationship between land use and soil erosion, visual interpretations of aerial photographs (scale 1:25.000), MSS-LANDSAT imagery (scale 1:250,000), as well as automatic interpretation of computer compatible tapes by IMAGE-100 system were carried out. From visual interpretation the following data were obtained: land use and cover tapes, slope classes, ravine frequency, and a texture sketch map. During field work, soil samples were collected for texture and X-ray analysis. The texture sketch map indicate that the areas with higher slope angles have a higher susceptibilty to the development of gullies. Also, the over carriage of pastureland, together with very friable lithologies (mainly sandstone) occuring in that area, seem to be the main factors influencing the catastrophic extension of ravines in the study site.

  13. Hepatic Lipidosis in a Research Colony of Big Brown Bats (Eptesicus fuscus).

    Science.gov (United States)

    Snyder, Jessica M; Treuting, Piper M; Brabb, Thea; Miller, Kimberly E; Covey, Ellen; Lencioni, Karen L

    2015-04-01

    During a nearby construction project, a sudden decrease in food intake and guano production occurred in an outdoor colony of big brown bats (Eptesicus fuscus), and one animal was found dead. Investigation revealed that the project was generating a large amount of noise and vibration, which disturbed the bats' feeding. Consequently the bats were moved into an indoor enclosure away from the construction noises, and the colony resumed eating. Over the next 3 wk, additional animals presented with clinical signs of lethargy, weight loss, ecchymoses, and icterus and were necropsied. Gross necropsy of the affected bats revealed large, pale yellow to tan, friable livers with rounded edges that floated when placed in 10% neutral-buffered formalin. Some bats had ecchymoses on the webbing and skin and gross perirenal hemorrhage. Histologic examination showed hepatic and renal tubular lipidosis. The clinical and pathologic signs of hemorrhage and icterus were suggestive of hepatic failure. Hepatic lipidosis was attributed to stress and inappetence associated with environmental perturbations. Once the environmental stressor was removed, the colony morbidity and mortality decreased. However, 2 y later, a series of new environmental stressors triggered additional deaths associated with hepatic lipidosis. Over a 9-y period, 21 cases of hepatic lipidosis were diagnosed in this bat colony.

  14. Experimental Pseudomonas anguilliseptica infection in turbot Psetta maxima (L.: a histopathological and immunohistochemical study

    Directory of Open Access Journals (Sweden)

    JL Romalde

    2009-06-01

    Full Text Available Experimental infection with Pseudomonas anguilliseptica was performed both by intraperitoneal (i.p. and bath route on juvenile turbot (Psetta maxima in order to evaluate the pathology induced. Turbot was found to be sensitive to i.p. challenge (1.7x106 CFU/fish but no to bath exposure. The i.p. challenge induced septicaemic infection and mortality. Externally, moribund fish showed distended abdomen and pale areas at day 9. The gross pathological internal signs present were abundant ascitic fluid in the peritoneal cavity, pale and enlarged spleen, pale and friable liver, and congestive and dilated gut with yellowish exudates. On histopathological examination, bacterial invasion was common in all the tissues studied but the most prominent pathological changes were observed in gut, spleen and kidney after 7 day with features of necrosis. The immunohistochemical findings support the widespread localization of the bacteria after the i.p. injection since the P. anguilliseptica was detected in spleen from day 1 post injection, in liver, kidney and gut from day 4, in muscle from day 7 and in brain from day 9. The difficulties in infecting healthy fish by bath challenge can be explained by the opportunistic nature of this pathogen.

  15. Early closure of postinfarction ventricular septal defects.

    Science.gov (United States)

    Martinelli, Luigi; Dottori, Vincenzo; Caputo, Enrico; Graffigna, Angelo; Pederzolli, Carlo

    2003-05-01

    According to the guidelines of the American College of Cardiology/American Heart Association early closure of postinfarction septal defects is now a class I indication although it still carries a relevant morbidity and mortality. The operative risk is related both to the critical hemodynamic conditions of the patient and to the technical difficulties posed by the friable tissue of the infarcted area. The most recent techniques involving the use of pericardial patches reinforced by acrylic glue have significantly reduced the hospital mortality. The aim of this study was to discuss the reliability of an aggressive, tissue-sparing surgical approach to this complication. We present a consecutive series of 12 patients operated upon between January 1998 and October 2001 within 12 hours of the onset of clinical evidence of postinfarction septal rupture. Repair was achieved with minimal septal debridement and the use of a large pericardial patch reinforced by a biological glue. Three cases of dehiscence required early reoperation with no hospital mortality. This procedure is technically feasible and allows early aggressive treatment of postinfarction septal rupture with satisfactory results.

  16. Overexpression of rice thaumatin-like protein (Ostlp gene in transgenic cassava results in enhanced tolerance to Colletotrichum gloeosporioides f. sp. manihotis

    Directory of Open Access Journals (Sweden)

    Patroba Odeny Ojola

    2018-06-01

    Full Text Available Cassava (Manihot esculenta Crantz is the most important staple food for more than 300 million people in Africa, and anthracnose disease caused by Colletotrichum gloeosporioides f. sp. manihotis is the most destructive fungal disease affecting cassava production in sub-Saharan Africa. The main objective of this study was to improve anthracnose resistance in cassava through genetic engineering. Transgenic cassava plants harbouring rice thaumatin-like protein (Ostlp gene, driven by the constitutive CaMV35S promoter, were generated using Agrobacterium-mediated transformation of friable embryogenic calli (FEC of cultivar TMS 60444. Molecular analysis confirmed the presence, integration, copy number of the transgene all the independent transgenic events. Semi-quantitative RT-PCR confirmed high expression levels of Ostlp in six transgenic lines tested. The antifungal activity of the transgene against Colletotrichum gloeosporioides pathogen was evaluated using the leaves and stem cuttings bioassay. The results demonstrated significantly delayed disease development and reduced size of necrotic lesions in leaves and stem cuttings of all transgenic lines compared to the leaves and stem cuttingss of non-transgenic control plants. Therefore, constitutive overexpression of rice thaumatin-like protein in transgenic cassava confers enhanced tolerance to the fungal pathogen C. gloeosporioides f. sp. manihotis. These results can therefore serve as an initial step towards genetic engineering of farmer-preffered cassava cultivars for resistance to anthracnose disease. Keywords: Colletotrichum gloeosporioides f. sp. manihotis, Thaumatin-like protein, Transgenic cassava

  17. Retrobulbar adenocarcinoma in an Amazon parrot (Amazona autumnalis).

    Science.gov (United States)

    Watson, Victoria E; Murdock, Jessica H; Cazzini, Paola; Schnellbacher, Rodney; Divers, Stephen J; Sakamoto, Kaori

    2013-03-01

    Retrobulbar neoplasms are not common in mammals and are even more infrequently seen in nonmammalian species. The current report describes a retrobulbar mass creating exophthalmia and neurologic signs in a red-lored Amazon parrot (Amazona autumnalis). A 27-year-old female parrot presented for a 3-day history of anorexia and a 2-week history of periocular soft tissue swelling and exophthalmia of the right eye. Physical examination revealed 9% dehydration and right eye exophthalmia with inability to retropulse the globe. A fine-needle aspirate was performed, and cytologic evaluation revealed necrotic debris with scattered clusters of epithelial cells, moderate numbers of macrophages, and few heterophils. Given the possibility of neoplasia and paucity of treatment options, the owners elected euthanasia and submitted the body for necropsy. A large, fluctuant, friable, red, retrobulbar mass with multiple areas of hemorrhage, on cut surface, was noted at necropsy. Histologically, the mass was composed of neoplastic, cuboidal to columnar epithelial cells, forming rosette-like glandular structures, admixed with abundant necrotic debris. The neoplastic cells were strongly positive for cytokeratin (AE1/AE3) by immunohistochemistry. Based on histopathology and immunohistochemistry, the mass was diagnosed as an adenocarcinoma.

  18. Coated particle waste form development

    International Nuclear Information System (INIS)

    Oma, K.H.; Buckwalter, C.Q.; Chick, L.A.

    1981-12-01

    Coated particle waste forms have been developed as part of the multibarrier concept at Pacific Northwest Laboratory under the Alternative Waste Forms Program for the Department of Energy. Primary efforts were to coat simulated nuclear waste glass marbles and ceramic pellets with low-temperature pyrolytic carbon (LT-PyC) coatings via the process of chemical vapor deposition (CVD). Fluidized bed (FB) coaters, screw agitated coaters (SAC), and rotating tube coaters were used. Coating temperatures were reduced by using catalysts and plasma activation. In general, the LT-PyC coatings did not provide the expected high leach resistance as previously measured for carbon alone. The coatings were friable and often spalled off the substrate. A totally different concept, thermal spray coating, was investigated at PNL as an alternative to CVD coating. Flame spray, wire gun, and plasma gun systems were evaluated using glass, ceramic, and metallic coating materials. Metal plasma spray coatings (Al, Sn, Zn, Pb) provided a two to three orders-of-magnitude increase in chemical durability. Because the aluminum coatings were porous, the superior leach resistance must be due to either a chemical interaction or to a pH buffer effect. Because they are complex, coated waste form processes rank low in process feasibility. Of all the possible coated particle processes, plasma sprayed marbles have the best rating. Carbon coating of pellets by CVD ranked ninth when compared with ten other processes. The plasma-spray-coated marble process ranked sixth out of eleven processes

  19. Late Miocene-Early Pliocene reactivation of the Main Boundary Thrust: Evidence from the seismites in southeastern Kumaun Himalaya, India

    Science.gov (United States)

    Mishra, Anurag; Srivastava, Deepak C.; Shah, Jyoti

    2013-05-01

    Tectonic history of the Himalaya is punctuated by successive development of the faults that run along the boundaries between different lithotectonic terrains. The Main Boundary Fault, defining the southern limit of the Lesser Himalayan terrain, is tectonically most active. A review of published literature reveals that the nature and age of reactivation events on the Main Boundary Fault is one of the poorly understood aspects of the Himalayan orogen. By systematic outcrop mapping of the seismites, this study identifies a Late Miocene-Early Pliocene reactivation on the Main Boundary Thrust in southeast Kumaun Himalaya. Relatively friable and cohesionless Neogene sedimentary sequences host abundant soft-sediment deformation structures in the vicinity of the Main Boundary Thrust. Among a large variety of structures, deformed cross-beds, liquefaction pockets, slump folds, convolute laminations, sand dykes, mushroom structures, fluid escape structures, flame and load structures and synsedimentary faults are common. The morphological attributes, the structural association and the distribution pattern of the soft-sediment deformation structures with respect to the Main Boundary Fault strongly suggest their development by seismically triggered liquefaction and fluidization. Available magnetostratigraphic age data imply that the seismites were developed during a Late Miocene-Early Pliocene slip on the Main Boundary Thrust. The hypocenter of the main seismic event may lie on the Main Boundary Thrust or to the north of the study area on an unknown fault or the Basal Detachment Thrust.

  20. Ikaite pseudomorphs in the Zaire deep-sea fan: An intermediate between calcite and porous calcite

    Science.gov (United States)

    Jansen, J. H. F.; Woensdregt, C. F.; Kooistra, M. J.; van der Gaast, S. J.

    1987-03-01

    Translucent brown aggregates of calcium-carbonate crystals have been found in cores from the Zaire deep-sea fan (west equatorial Africa). The aggregates are well preserved but very friable. Upon storage they become yellowish white and cloudy and release water. Chemical, mineralogical (XRD), petrographical, crystal-morphological, and stable-isotope data demonstrate that the crystals have passed through three phases: (1) an authigenic carbonate phase, probably calcium carbonate, which is represented by the external habit of the present crystals; (2) a translucent brown ikaite phase (CaCO3·6H2O), unstable at temperatures above 5 °C; and (3) a phase consisting of calcite microcrystals that are poorly cemented and form a porous mass within the crystal form of the morphologically unchanged first phase. The transformation from the first phase into ikaite was probably a kinetic replacement. The transformation from ikaite into the third phase occurred because of storage at room temperature. The presence of ikaite is indicative of a low-temperature, anaerobic, organic-carbon-rich marine environment. Ikaite is probably the precursor of a great number of porous calcite pseudomorphs, and possibly also of many marine authigenic microcrystalline carbonate nodules.

  1. Postmenopausal intestinal obstructive endometriosis: case report and review of the literature

    Directory of Open Access Journals (Sweden)

    Pedro Popoutchi

    Full Text Available CONTEXT: Endometriosis is characterized by the presence of endometrial tissue outside the uterine cavity, which is commonly detected in gynecological practice but rarely reported as a coloproctological disorder. The objective of the present report was to discuss a rare case of postmenopausal intestinal endometriosis simulating a malignant lesion, following a review of the literature. CASE REPORT: A 74-year-old woman with complaints of hematochezia and tenesmus of two months' duration accompanied by liquid feces and pelvic pain, but with no other gastrointestinal or gynecological complaints, was referred to our service. She had been menopausal for 22 years, with no hormone replacement treatment, and had undergone panhysterectomy three years before the referral to us, due to endometrial thickening and a right adnexal cyst. Five months before this referral, she had undergone laparotomy due to acute obstructive abdomen, which revealed a tumor mass involving the small bowel. Anatomopathological examination of the enterectomy suggested a hypothesis of intestinal endometriosis. A proctological examination was normal. Computed tomography of the pelvis revealed thickening of the rectosigmoid transition and colonoscopy revealed friable tumor formation in the rectum. A biopsy of the lesion revealed mucosal fragments of endometrial type, which led to a review of the previous anatomopathological examination. The patient underwent rectosigmoidectomy with protective transversotomy, with a good postoperative course, and anatomical examination confirmed the intestinal endometriosis. The patient subsequently suffered a stenosing recurrence of the lesion and has undergone colostomy since then.

  2. The fabrication of YBCO superconductor polycrystalline powder by CCSO

    International Nuclear Information System (INIS)

    Martirosyan, K S; Luss, D; Galstyan, E; Xue, Y Y

    2008-01-01

    We present a novel, cost-effective and simple method to produce polycrystalline superconductor YBa 2 Cu 3 O 7-δ (YBCO) powder by a self-sustaining one-step process called carbon combustion synthesis of oxides (CCSO). In this process the exothermic oxidation of carbon nanoparticles generates a thermal wave that propagates at a velocity of about 1 mm s -1 through the solid yttrium, barium, and copper precursors, converting them rapidly (in the order of seconds) to polycrystalline YBCO. The carbon is not incorporated in the product and is emitted as carbon dioxide (CO 2 ) from the sample, generating a highly porous (∼70%) and friable product. Most of the grains have a plate-like shape, are well connected, and have a size of between 1 and 3 μm. The concentration of the residual carbon was less than 0.06 wt%. The magnetization of as-synthesized samples (without external post-annealing in oxygen), as determined by a SQUID magnetometer, showed an onset of the superconducting (SC) transition at ∼91 K, with a 44% shielding fraction of the -1/(4π) value

  3. Summary environmental site assessment report for the U.S. Department of Energy Oxnard Facility, Oxnard, California

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    This report summarizes the investigations conducted by Rust Geotech at the U.S. Department of Energy (DOE) Oxnard facility, 1235 East Wooley Road, Oxnard, California. These investigations were designed to locate, identify, and characterize any regulated contaminated media on the site. The effort included site visits; research of ownership, historical uses of the Oxnard facility and adjacent properties, incidences of and investigations for contaminants on adjacent properties, and the physical setting of the site; sampling and analysis; and reporting. These investigations identified two friable asbestos gaskets on the site, which were removed, and nonfriable asbestos, which will be managed through the implementation of an asbestos management plan. The California primary drinking water standards were exceeded for aluminum on two groundwater samples and for lead in one sample collected from the shallow aquifer underlying the site; remediation of the groundwater in this aquifer is not warranted because it is not used. Treated water is available from a municipal water system. Three sludge samples indicated elevated heavy metals concentrations; the sludge must be handled as a hazardous waste if disposed. Polychlorinated biphenyls (PCBs) were detected at concentrations below remediation criteria in facility soils at two locations. In accordance with U.S. Environmental Protection Agency (EPA) and State of California guidance, remediation of the PCBs is not required. No other hazardous substances were detected in concentrations exceeding regulatory limits.

  4. Environment-oriented low-cost porous mullite ceramic membrane supports fabricated from coal gangue and bauxite

    Energy Technology Data Exchange (ETDEWEB)

    Lü, Qikai [Institute of Urban Environment, Chinese Academy of Sciences, Xiamen (China); Ningbo Urban Environment Observation and Research Station-NUEORS, Chinese Academy of Sciences, Ningbo (China); School of Chemistry and Chemical Engineering, South China University of Technology, Guangzhou (China); Dong, Xinfa [School of Chemistry and Chemical Engineering, South China University of Technology, Guangzhou (China); Zhu, Zhiwen [Institute of Urban Environment, Chinese Academy of Sciences, Xiamen (China); Ningbo Urban Environment Observation and Research Station-NUEORS, Chinese Academy of Sciences, Ningbo (China); Dong, Yingchao, E-mail: ycdong@iue.ac.cn [Institute of Urban Environment, Chinese Academy of Sciences, Xiamen (China); Ningbo Urban Environment Observation and Research Station-NUEORS, Chinese Academy of Sciences, Ningbo (China)

    2014-05-01

    Highlights: • Coal gangue was recycled to fabricate low-cost porous mullite membrane supports. • A unique volume-expansion occurred due to a mullitization-crystal-growth process. • A porous structure consists of glassy particles and embedded mullite crystals. - Abstract: Porous mullite ceramic supports for filtration membrane were successfully fabricated via recycling of coal gangue and bauxite at sintering temperatures from 1100 to 1500 °C with corn starch as pore-forming agent. The dynamic sintering behaviors, phase evolution, shrinkage, porosity and pore size, gas permeation flux, microstructure and mechanical property were systematically studied. A unique volume-expansion stage was observed at increased temperatures from 1276 to 1481 °C caused by a mullitization-crystal-growth process. During this stage, open porosity increases and pore size distributions broaden, which result in a maximum of nitrogen gas flux at 1400 °C. The X-ray diffraction results reveal that secondary mullitization took place from 1100 °C and the major phase is mullite with a content of ∼84.7 wt.% at 1400 °C. SEM images show that the as-fabricated mullite supports have a porous microstructure composed of sintered glassy particles embedded with inter-locked mullite crystals, which grew gradually with increasing temperature from rod-like into blocky-like morphologies. To obtain mullite membrane supports with sufficient porosity and acceptable mechanical strength, the relationship between porosity and mechanical strength was investigated, which was fitted using a parabolic equation.

  5. Isothermal Oxidation of Magnetite to Hematite in Air and Cyclic Reduction/Oxidation Under Carbon Looping Combustion Conditions

    Science.gov (United States)

    Simmonds, Tegan; Hayes, Peter C.

    2017-12-01

    In the carbon looping combustion process the oxygen carrier is regenerated through oxidation in air; this process has been simulated by the oxidation of dense synthetic magnetite for selected temperatures and times. The oxidation of magnetite in air is shown to occur through the formation of dense hematite layers on the particle surface. This dense hematite forms through lath type shear transformations or solid-state diffusion through the product layer. Cyclic reduction in CO-CO2/oxidation in air of hematite single crystals has been carried out under controlled laboratory conditions at 1173 K (900 °C). It has been shown that the initial reduction step is critical to determining the product microstructure, which consists of gas pore dendrites in the magnetite matrix with blocky hematite formed on the pore surfaces. The progressive growth of the magnetite layer with the application of subsequent cycles appears to continue until no original hematite remains, after which physical disintegration of the particles takes place.

  6. Generation of fine hydromagmatic ash by growth and disintegration of glassy rinds

    Science.gov (United States)

    Mastin, L.G.

    2007-01-01

    The deposits of mafic hydromagmatic eruptions are more fine grained and variable in vesicularity than dry magmatic deposits. Blocky, equant shapes of many hydromagmatic clasts also contrast with droplet, thread, and bubble wall morphology of dry magmatic fragments. Small (disintegration of glassy rinds on pyroclast surfaces as they deform within turbulent flows. This process, termed "turbulent shedding", may occur during the expansion phase of vapor explosions or during turbulent but nonexplosive mixing of magma with water, steam, or water sprays. The occurrence of turbulent shedding and the resulting fragment sizes depend on the timescale for rind growth and the timescale between disturbances that remove or disintegrate glassy rinds. Turbulent shedding is directly observable in some small littoral jets at Kilauea. Calculations suggest that, in the presence of liquid water or water sprays, glassy rinds having a thickness of microns to millimeters should form in milliseconds to seconds. This is similar to the timescale between turbulent velocity fluctuations that can shred lava globules and remove such rinds. The fraction of a deposit consisting of fine ash should increase with the duration of this process: Large-scale Surtseyan jets generate hundreds or thousands of shedding events; bubble bursts or tephra jets at Kilauea's coast may produce only a few.

  7. Laser cladding of in situ TiB2/Fe composite coating on steel

    International Nuclear Information System (INIS)

    Du Baoshuai; Zou Zengda; Wang Xinhong; Qu Shiyao

    2008-01-01

    To enhance the wear resistance of mechanical components, laser cladding has been applied to deposit in situ TiB 2 /Fe composite coating on steel using ferrotitanium and ferroboron as the coating precursor. The phase constituents and microstructure of the composite coating were investigated using X-ray diffraction (XRD), scanning electron micrograph (SEM) and electron probe microanalysis (EPMA). Microhardness tester and block-on-ring wear tester were employed to measure the microhardness and dry-sliding wear resistance of the composite coating. Results show that defect-free composite coating with metallurgical joint to the steel substrate can be obtained. Phases presented in the coating consist of TiB 2 and α-Fe. TiB 2 particles which are formed in situ via nucleation-growth mechanism are distributed uniformly in the α-Fe matrix with blocky morphology. The microhardness and wear properties of the composite coating improved significantly in comparison to the as-received steel substrate due to the presence of the hard reinforcement TiB 2

  8. Dispersal of volcaniclasts during deep-sea eruptions: Settling velocities and entrainment in buoyant seawater plumes

    Science.gov (United States)

    Barreyre, Thibaut; Soule, S. Adam; Sohn, Robert A.

    2011-08-01

    We use tank experiments to measure settling rates of deep-sea volcaniclastic material recovered from the Arctic (85°E Gakkel Ridge) and Pacific (Juan de Fuca Ridge, Loihi seamount) Oceans. We find that clast size and shape exert a strong influence on settling velocity, with velocities of ~ 30 cm/s for large (~ 8 mm), blocky clasts, compared to velocities of ~ 2.5 cm/s for small (Pele) entrained in a megaplume could be advected as far as a few kilometers from a source region. These results indicate that entrainment in buoyant seawater plumes during an eruption may play an important role in clast dispersal, but it is not clear if this mechanism can explain the distribution of volcaniclastic material at the sites on the Gakkel and Juan de Fuca Ridges where our samples were acquired. In order to understand the dispersal of volcaniclastic material in the deep-sea it will be necessary to rigorously characterize existing deposits, and develop models capable of incorporating explosive gas phases into the eruption plume.

  9. High resolution cathodoluminescence spectroscopy of carbonate cementation in Khurmala Formation (Paleocene-L. Eocene) from Iraqi Kurdistan Region, Northern Iraq

    Science.gov (United States)

    Omer, Muhamed F.; Omer, Dilshad; Zebari, Bahroz Gh.

    2014-12-01

    A combination of high resolution cathodoluminsecnce-spectroscopy (HRS-CL) with spatial electron microprobe analysis and optical microscopy is used to determine paragenesis and history of cementation in the limestones and dolostones of Khurmala Formation which is exposed in many parts of Northern Iraq. Khurmala Formation was subjected to different diagenetic processes such as micritization, compaction, dissolution, neomorphism, pyritization and cementation that occurred during marine to shallow burial stages and culminated during intermediate to deep burial later stages. Five dolomite textures are recognized and classified according to crystal size distribution and crystal-boundary shape. Dolomitization is closely associated with the development of secondary porosity that pre-and postdates dissolution and corrosion; meanwhile such porosity was not noticed in the associated limestones. Microprobe analysis revealed three types of cement, calcite, dolomite and ankerite which range in their luminescence from dull to bright. Cathodoluminescence study indicated four main texture generations. These are (1) unzoned microdolomite of planar and subhedral shape, with syntaxial rim cement of echinoderm that show dull to red luminescence, (2) equant calcite cements filling interparticle pores which shows dull luminescence and weak zonal growth, (3.1) homogenous intrinsic blue stoichiometric calcite with dull luminescence and without activators, (3.2) coarse blocky calcite cement with strong oscillatory zoning and bright orange luminescence which postdates other calcite cements, (4) ankerite cement with red to orange, non-luminescence growth zonation which is the last formed cement.

  10. Effect of Prior Austenite Grain Size on the Morphology of Nano-Bainitic Steels

    Science.gov (United States)

    Singh, Kritika; Kumar, Avanish; Singh, Aparna

    2018-04-01

    The strength in nanostructured bainitic steels primarily arises from the fine platelets of bainitic ferrite embedded in carbon-enriched austenite. However, the toughness is dictated by the shape and volume fraction of the retained austenite. Therefore, the exact determination of processing-morphology relationships is necessary to design stronger and tougher bainite. In the current study, the morphology of bainitic ferrite in Fe-0.89C-1.59Si-1.65Mn-0.37Mo-1Co-0.56Al-0.19Cr (wt pct) bainitic steel has been investigated as a function of the prior austenite grain size (AGS). Specimens were austenitized at different temperatures ranging from 900 °C to 1150 °C followed by isothermal transformation at 300 °C. Detailed microstructural characterization has been carried out using scanning electron microscopy and X-ray diffraction. The results showed that the bainitic laths transformed in coarse austenite grains are finer resulting in higher hardness, whereas smaller austenite grains lead to the formation of thicker bainitic laths with a large fraction of blocky type retained austenite resulting in lower hardness.

  11. Continuous cooling transformation behavior and impact toughness in heat-affected zone of Nb-containing fire-resistant steel

    Science.gov (United States)

    Wang, Hong Hong; Qin, Zhan Peng; Wan, Xiang Liang; Wei, Ran; Wu, Kai Ming; Misra, Devesh

    2017-09-01

    Simulated heat-affected zone continuous cooling transformation diagram was developed for advanced fireresistant steel. Over a wide range of cooling rates, corresponding to t8/5 from 6 s to 150 s, granular bainite was the dominant transformation constituent, while the morphology of less dominant martensite-austenite (M-A) constituent changed from film-like to block-type constituent; but the hardness remained similar to the average value of 190-205 HV (0.2). The start and finish transformation temperature was high at 700 °C and 500 °C, and is different from the conventional high strength low alloy steels. It is believed that the high-content (0.09 wt%) of Nb may promote bainite transformation at relatively high temperatures. Martenistic matrix was not observed at high cooling rate and the film-like M-A constituent and blocky M-A constituent with thin film of retained austenite and lath martensite were observed on slow cooling. Excellent impact toughness was obtained in the heat-affected zone with 15-75 kJ/cm welding heat input.

  12. Twin-spot laser welding of advanced high-strength multiphase microstructure steel

    Science.gov (United States)

    Grajcar, Adam; Morawiec, Mateusz; Różański, Maciej; Stano, Sebastian

    2017-07-01

    The study addresses the results concerning the laser welding of TRIP (TRansformation Induced Plasticity) steel using a beam focused at two spots (also referred to as twin-spot laser welding). The analysis involved the effect of variable welding thermal cycles on the properties and microstructure of welded joints. The tests were performed using a linear energy of 0.048 and 0.060 kJ/mm and the laser beam power distribution of 50%:50%, 60%:40% and 70%:30%. The tests also involved welding performed using a linear energy of 0.150 kJ/mm and the laser beam power distribution of 70%:30%. In addition, the research included observations of the microstructure of the fusion zone, heat affected zone and the transition zone using light microscopy and scanning electron microscopy. The fusion zone was composed of blocky-lath martensite whereas the HAZ (heat-affected zone) was characterised by the lath microstructure containing martensite, bainite and retained austenite. The distribution of twin-spot laser beam power significantly affected the microstructure and hardness profiles of welded joints. The highest hardness (480-505 HV), regardless of welding variants used, was observed in the HAZ.

  13. The Influence of Chain Microstructure of Biodegradable Copolyesters Obtained with Low-Toxic Zirconium Initiator to In Vitro Biocompatibility

    Science.gov (United States)

    Orchel, Arkadiusz; Kasperczyk, Janusz; Marcinkowski, Andrzej; Pamula, Elzbieta; Orchel, Joanna; Bielecki, Ireneusz

    2013-01-01

    Because of the wide use of biodegradable materials in tissue engineering, it is necessary to obtain biocompatible polymers with different mechanical and physical properties as well as degradation ratio. Novel co- and terpolymers of various composition and chain microstructure have been developed and applied for cell culture. The aim of this study was to evaluate the adhesion and proliferation of human chondrocytes to four biodegradable copolymers: lactide-coglycolide, lactide-co-ε-caprolactone, lactide-co-trimethylene carbonate, glycolide-co-ε-caprolactone, and one terpolymer glycolide-colactide-co-ε-caprolactone synthesized with the use of zirconium acetylacetonate as a nontoxic initiator. Chain microstructure of the copolymers was analyzed by means of 1H and 13C NMR spectroscopy and surface properties by AFM technique. Cell adhesion and proliferation were determined by CyQUANT Cell Proliferation Assay Kit. After 4 h the chondrocyte adhesion on the surface of studied materials was comparable to standard TCPS. Cell proliferation occurred on all the substrates; however, among the studied polymers poly(L-lactide-coglycolide) 85 : 15 that characterized the most blocky structure best supported cell growth. Chondrocytes retained the cell membrane integrity evaluated by the LDH release assay. As can be summarized from the results of the study, all the studied polymers are well tolerated by the cells that make them appropriate for human chondrocytes growth. PMID:24062998

  14. Total-variation based velocity inversion with Bregmanized operator splitting algorithm

    Science.gov (United States)

    Zand, Toktam; Gholami, Ali

    2018-04-01

    Many problems in applied geophysics can be formulated as a linear inverse problem. The associated problems, however, are large-scale and ill-conditioned. Therefore, regularization techniques are needed to be employed for solving them and generating a stable and acceptable solution. We consider numerical methods for solving such problems in this paper. In order to tackle the ill-conditioning of the problem we use blockiness as a prior information of the subsurface parameters and formulate the problem as a constrained total variation (TV) regularization. The Bregmanized operator splitting (BOS) algorithm as a combination of the Bregman iteration and the proximal forward backward operator splitting method is developed to solve the arranged problem. Two main advantages of this new algorithm are that no matrix inversion is required and that a discrepancy stopping criterion is used to stop the iterations, which allow efficient solution of large-scale problems. The high performance of the proposed TV regularization method is demonstrated using two different experiments: 1) velocity inversion from (synthetic) seismic data which is based on Born approximation, 2) computing interval velocities from RMS velocities via Dix formula. Numerical examples are presented to verify the feasibility of the proposed method for high-resolution velocity inversion.

  15. Effects of grain refinement on cast structure and tensile properties of superalloy K4169 at high pouring temperature

    Directory of Open Access Journals (Sweden)

    Zi-qi Jie

    2016-03-01

    Full Text Available In order to improve the filling ability of large complex thin wall castings, the pouring temperature should be increased, but this will result in the grain coarsening. To overcome this problem, two kinds of grain refiners of Co-Fe-Nb and Cr-Fe-Nb ternary alloys, which contain high stability compound particles, were prepared. The effects of the refiners on the as-cast structures and tensile properties of the K4169 superalloy with different casting conditions were studied by analyzing specimens 110 mm long and 20 mm in diameter. Results showed that the mixture addition of the two refiners in the melt of K4169 can reduce the columnar grain region and decrease the equiaxed grain size greatly. After refinement, the amount of Laves phase decreases and its morphology changes from island to blocky structure. The carbides in the fine grain samples are fine and dispersive. Meanwhile, the porosity in specimens is decreased due to grain refinement. As a result, the yield strength, ultimate strength and the elongation of the specimens are increased. The grain refinement mechanisms are also discussed.

  16. UT inspection of nozzles by 3D raytracing

    International Nuclear Information System (INIS)

    Isenberg, J.; Koshy, M.; Carcione, L.

    2004-01-01

    This paper documents how we have adapted 3D geometric modeling and ray tracing to support design and verification of wedges and preparation of coverage maps for ultrasonic inspection of BWR nozzles. This software is capable of addressing a broad range of modeling issues, including ray tracing in completely general 3D objects comprised of blocky, transversely isotropic material. However, to capitalize on the full range of capability usually requires an investment of time on the part of users. To make 3D modeling accessible to users who have time-urgent requirements or who do not need to utilize the full capabilities of the software, we have developed specialized applications in which restrictions on generality are accepted in exchange for easy access to model building, wedge design and coverage maps for detecting flaws in the bore and inner blend regions of nozzles. This is done by providing partially-completed, parametrized models which give the user latitude to generate general models within a fixed framework. We also provide a graphical user interface which anticipates certain tasks that a user will wish to undertake; other tasks may readily be added. (author)

  17. σ and η Phase formation in advanced polycrystalline Ni-base superalloys

    Energy Technology Data Exchange (ETDEWEB)

    Antonov, Stoichko, E-mail: santonov@hawk.iit.edu [Illinois Institute of Technology, 10 W. 32nd Street, Chicago, IL 60616 (United States); Huo, Jiajie; Feng, Qiang [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China); Isheim, Dieter; Seidman, David N. [Department of Materials Science and Engineering, Northwestern University, 2220 Campus Drive, Evanston, IL 60208 (United States); Northwestern University Center for Atom Probe Tomography (NUCAPT), 2220 Campus Drive, Evanston, IL 60208 (United States); Helmink, Randolph C.; Sun, Eugene [Rolls-Royce Corporation, 450 S. Meridian Street, Indianapolis, IN 46225 (United States); Tin, Sammy [Illinois Institute of Technology, 10 W. 32nd Street, Chicago, IL 60616 (United States)

    2017-02-27

    In polycrystalline Ni-base superalloys, grain boundary precipitation of secondary phases can be significant due to the effects they pose on the mechanical properties. As new alloying concepts for polycrystalline Ni-base superalloys are being developed to extend their temperature capability, the effect of increasing levels of Nb alloying additions on long term phase stability and the formation of topologically close packed (TCP) phases needs to be studied. Elevated levels of Nb can result in increased matrix supersaturation and promote the precipitation of secondary phases. Long term thermal exposures on two experimental powder processed Ni-base superalloys containing various levels of Nb were completed to assess the stability and precipitation of TCP phases. It was found that additions of Nb promoted the precipitation of η-Ni{sub 6}AlNb along the grain boundaries in powder processed, polycrystalline Ni-base superalloys, while reduced Nb levels favored the precipitation of blocky Cr and Mo – rich σ phase precipitates along the grain boundary. Evaluation of the thermodynamic stability of these two phases in both alloys using Thermo-calc showed that while σ phase predictions are fairly accurate, predictions of the η phase are limited.

  18. Content-Aware Scalability-Type Selection for Rate Adaptation of Scalable Video

    Directory of Open Access Journals (Sweden)

    Tekalp A Murat

    2007-01-01

    Full Text Available Scalable video coders provide different scaling options, such as temporal, spatial, and SNR scalabilities, where rate reduction by discarding enhancement layers of different scalability-type results in different kinds and/or levels of visual distortion depend on the content and bitrate. This dependency between scalability type, video content, and bitrate is not well investigated in the literature. To this effect, we first propose an objective function that quantifies flatness, blockiness, blurriness, and temporal jerkiness artifacts caused by rate reduction by spatial size, frame rate, and quantization parameter scaling. Next, the weights of this objective function are determined for different content (shot types and different bitrates using a training procedure with subjective evaluation. Finally, a method is proposed for choosing the best scaling type for each temporal segment that results in minimum visual distortion according to this objective function given the content type of temporal segments. Two subjective tests have been performed to validate the proposed procedure for content-aware selection of the best scalability type on soccer videos. Soccer videos scaled from 600 kbps to 100 kbps by the proposed content-aware selection of scalability type have been found visually superior to those that are scaled using a single scalability option over the whole sequence.

  19. Wear behaviors of pure aluminum and extruded aluminum alloy (AA2024-T4) under variable vertical loads and linear speeds

    Science.gov (United States)

    Jung, Jeki; Oak, Jeong-Jung; Kim, Yong-Hwan; Cho, Yi Je; Park, Yong Ho

    2017-11-01

    The aim of this study was to investigate the transition of wear behavior for pure aluminum and extruded aluminum alloy 2024-T4 (AA2024-T4). The wear test was carried using a ball-on-disc wear testing machine at various vertical loads and linear speeds. The transition of wear behaviors was analyzed based on the microstructure, wear tracks, wear cross-section, and wear debris. The critical wear rates for each material are occurred at lower linear speed for each vertical load. The transition of wear behavior was observed in which abrasion wears with the generation of an oxide layer, fracture of oxide layer, adhesion wear, severe adhesion wear, and the generation of seizure occurred in sequence. In case of the pure aluminum, the change of wear debris occurred in the order of blocky, flake, and needle-like debris. Cutting chip, flake-like, and coarse flake-like debris was occurred in sequence for the extruded AA2024-T4. The transition in the wear behavior of extruded AA2024-T4 occurred slower than in pure aluminum.

  20. Interaction between Nd-rich phase particles and liquid-solid interface in as-cast Ti-5Al-4Sn-2Zr-1Mo-0.25Si-1Nd titanium alloy

    International Nuclear Information System (INIS)

    Li, G.P.; Li, D.; Liu, Y.Y.; Hu, Z.Q.

    1995-01-01

    The composition (wt%) of ingot fir this investigation is 86.75%Ti, 5%Al, 4%Sn, 2%Zr, 1%Mo, 0.25%Si, 1%Nd. The alloy was prepared by vacuum arc melting in the form of buttons of mass 500 kg, which was remelted three times repeatedly to obtain homogeneous composition. The Nd-rich phase particles in the as-cast Ti-55 alloy are about 1.2∼11.07 microm and uniformly distribute in the matrix. The shapes of the particles are mainly ellipsoids together with short needle-like and blocky morphologies. The calculated diameter of the Nd-rich phase particles is ∼ 10 microm, which is within the 1.2∼11.07 microm range of the particle diameter experimentally measured in the as-cast Ti-55 alloy. The practical interface velocity is three orders of magnitude greater than V c, and the Nd-rich phase particles in the as-cast Ti-55 alloy are trapped by the liquid-solid interface

  1. Effect of magnesium content on the microstructure and dry sliding wear behavior of centrifugally cast functionally graded A356-Mg2Si in situ composites

    Science.gov (United States)

    Ram, Subhash Chandra; Chattopadhyay, K.; Chakrabarty, I.

    2018-04-01

    Functionally graded A356 alloy (Al–7.2Si–0.3Mg) –Mg2Si in situ composites have been synthesized via centrifugal casting route. Mg2Si particles tend to migrate towards the core of the tubular product by centrifugal force. The in situ formed Mg2Si particles in composites are characterized by x-ray diffraction (XRD) analysis, Energy dispersive spectrometry (EDS), Optical, Scanning Electron and Transmission Electron Microscopy. Apart from primary blocky Mg2Si particles the matrix contains other phases viz. Al-Si eutectic, pseudo-binary Al-Mg2Si eutectic and Al-Fe-Si intermetallics. Density is found to decrease and %porosity is increased with increase in volume fraction of Mg2Si. Maximum hardness was observed at the inner core region due to maximum segregation of Mg2Si particles and gradually decreases towards the outer periphery region. The dry sliding wear was evaluated with varying parameters such as normal loads (N) and sliding distances (m). A substantial increase in wear resistance at the inner core region is observed. From the worn surface characterization, the wear mechanisms have been explained.

  2. Microstructural evolution and deformation features in gas turbine blades operated in-service

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Fei [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Tong, Jinyan [National Center for Materials Service Safety, University of Science and Technology Beijing, Beijing 100083 (China); Feng, Qiang [National Center for Materials Service Safety, University of Science and Technology Beijing, Beijing 100083 (China); State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China); Zhang, Jianxin [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China)

    2015-01-05

    Highlights: • Gas turbine blades operated in-service have been investigated. • Two primary MC decomposition reactions take place during servicing. • Deformation features during servicing have been analyzed. - Abstract: The nickel based superalloy GH4037 is employed in gas turbine blades because of its high temperature strength and oxidation resistance. Microstructural evolution and deformation features in gas turbine blades after 1600 h service have been investigated by Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM). The microstructure of blade changes according to complex and comprehensive temperature and stress fields applied on it. Microstructural observations show that minor carbide precipitates dispersedly precipitate in the matrix. Two MC decomposition reactions occur: MC + γ → M{sub 23}C{sub 6} + γ′ and MC + γ → M{sub 23}C{sub 6} + η. Blocky, closely spaced M{sub 23}C{sub 6} particles continuously distribute along grain boundaries. The main deformation features, such as slip bands, APB-coupled dislocation pairs, stacking faults bound by partial dislocations and deformation twinning, have also been analyzed in terms of fundamental deformation mechanisms and environmental effects.

  3. The crystallography of fatigue crack initiation in Incoloy-908 and A-286 steel

    International Nuclear Information System (INIS)

    Krenn, C.R.

    1996-12-01

    Fatigue crack initiation in the austenitic Fe-Ni superalloys Incoloy-908 and A-286 is examined using local crystallographic orientation measurements. Results are consistent with sharp transgranular initiation and propagation occurring almost exclusively on {111} planes in Incoloy-908 but on a variety of low index planes in A-286. This difference is attributed to the influence of the semicoherent grain boundary η phase in A-286. Initiation in each alloy occurred both intergranularly and transgranularly and was often associated with blocky surface oxide and carbide inclusions. Taylor factor and resolved shear stress and strain crack initiation hypotheses were tested, but despite an inconclusive suggestion of a minimum required {111} shear stress, none of the hypotheses were found to convincingly describe preferred initiation sites, even within the subsets of transgranular cracks apparently free from the influence of surface inclusions. Subsurface inclusions are thought to play a significant role in crack initiation. These materials have applications for use in structural conduit for high field superconducting magnets designed for fusion energy use

  4. Microstructure of a Ni Matrix Composite Coating Reinforced by In-situ TiC Particles Using Plasma Cladding

    Institute of Scientific and Technical Information of China (English)

    WUYu-ping; WANGZe-hua; LINPing-hua

    2004-01-01

    Plasma cladding process was used to prepare the TiC/Ni composite coating on the mild steel substrates. The TiC particles were synthesized in-situ. Microstructure and properties of the coating were investigated by optical microscopy, X-Ray diffraction, SEM, TEM and microhardness tester. The results show that the interface between the coating and the substrate is metallurgically bonded. The coating was uniform and almost defect-free when [Ti+C] varied from 10% to 20% after ball milling. The microstructure of the coating is mainly composed of γ-Ni dendrite, interdendritic eutectic (γ-Ni austenite, M23C6 and CrB) and TiC particles. Most of the TiC particles are spherical and a small fraction is blocky in size of 1-2μm. The TiC particles are smaller at the bottom than near the top of the coating. The coating has a gradient microstructure and a highest hardness of 1000Hv0.1.

  5. Salt-body Inversion with Minimum Gradient Support and Sobolev Space Norm Regularizations

    KAUST Repository

    Kazei, Vladimir

    2017-05-26

    Full-waveform inversion (FWI) is a technique which solves the ill-posed seismic inversion problem of fitting our model data to the measured ones from the field. FWI is capable of providing high-resolution estimates of the model, and of handling wave propagation of arbitrary complexity (visco-elastic, anisotropic); yet, it often fails to retrieve high-contrast geological structures, such as salt. One of the reasons for the FWI failure is that the updates at earlier iterations are too smooth to capture the sharp edges of the salt boundary. We compare several regularization approaches, which promote sharpness of the edges. Minimum gradient support (MGS) regularization focuses the inversion on blocky models, even more than the total variation (TV) does. However, both approaches try to invert undesirable high wavenumbers in the model too early for a model of complex structure. Therefore, we apply the Sobolev space norm as a regularizing term in order to maintain a balance between sharp and smooth updates in FWI. We demonstrate the application of these regularizations on a Marmousi model, enriched by a chunk of salt. The model turns out to be too complex in some parts to retrieve its full velocity distribution, yet the salt shape and contrast are retrieved.

  6. Microstructural Evolution of Al-1Fe (Weight Percent) Alloy During Accumulative Continuous Extrusion Forming

    Science.gov (United States)

    Wang, Xiang; Guan, Ren-Guo; Tie, Di; Shang, Ying-Qiu; Jin, Hong-Mei; Li, Hong-Chao

    2018-04-01

    As a new microstructure refining method, accumulative continuous extrusion forming (ACEF) cannot only refine metal matrix but also refine the phases that exist in it. In order to detect the refinements of grain and second phase during the process, Al-1Fe (wt pct) alloy was processed by ACEF, and the microstructural evolution was analyzed by electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). Results revealed that the average grain size of Al-1Fe (wt pct) alloy decreased from 13 to 1.2 μm, and blocky Al3Fe phase with an average length of 300 nm was granulated to Al3Fe particle with an average diameter of 200 nm, after one pass of ACEF. Refinement of grain was attributed to continuous dynamic recrystallization (CDRX), and the granulation of Al3Fe phase included the spheroidization resulting from deformation heat and the fragmentation caused by the coupling effects of strain and thermal effect. The spheroidization worked in almost the entire deformation process, while the fragmentation required strain accumulation. However, fragmentation contributed more than spheroidization. Al3Fe particle stimulated the formation of substructure and retarded the migration of recrystallized grain boundary, but the effect of Al3Fe phase on refinement of grain could only be determined by the contrastive investigation of Al-1Fe (wt pct) alloy and pure Al.

  7. A study on the microstructure and mechanical properties of AISI D2 tool steel modified by niobium

    Energy Technology Data Exchange (ETDEWEB)

    Hamidzadeh, M.A.; Meratian, M. [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of); Mohammadi Zahrani, M., E-mail: iut.mohammadi@gmail.com [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of)

    2012-10-30

    The microstructure and mechanical properties of AISI D2 tool steel with up to 1.5 wt% niobium additions were investigated. The microstructural evolutions were characterized by means of optical microscopy and scanning electron microscopy techniques. Mechanical properties of the samples were measured using tensile testing, hardness measurements and Charpy impact test. The results indicated that modification of the microstructure was effectively achieved through the addition of 1.5 wt% of niobium, which refined the prior-austenite grains and decreased the volume fraction of eutectic carbides. Also, the eutectic carbide network tended to break thereby forming blocky and ribbon-like morphologies in the eutectic structures. The ductility and impact toughness of the niobium-contained steels were increased considerably and reached to about 5.8% and 15 J/cm{sup 2}, respectively. Generally, the results of this study suggest that niobium can be used as an alloying element to significantly enhance the ductility and impact toughness of D2 tool steel without affecting the hardness.

  8. A study on the microstructure and mechanical properties of AISI D2 tool steel modified by niobium

    International Nuclear Information System (INIS)

    Hamidzadeh, M.A.; Meratian, M.; Mohammadi Zahrani, M.

    2012-01-01

    The microstructure and mechanical properties of AISI D2 tool steel with up to 1.5 wt% niobium additions were investigated. The microstructural evolutions were characterized by means of optical microscopy and scanning electron microscopy techniques. Mechanical properties of the samples were measured using tensile testing, hardness measurements and Charpy impact test. The results indicated that modification of the microstructure was effectively achieved through the addition of 1.5 wt% of niobium, which refined the prior-austenite grains and decreased the volume fraction of eutectic carbides. Also, the eutectic carbide network tended to break thereby forming blocky and ribbon-like morphologies in the eutectic structures. The ductility and impact toughness of the niobium-contained steels were increased considerably and reached to about 5.8% and 15 J/cm 2 , respectively. Generally, the results of this study suggest that niobium can be used as an alloying element to significantly enhance the ductility and impact toughness of D2 tool steel without affecting the hardness.

  9. Effect of heat treatment on the microstructure of Co-Cr-W alloy fabricated by laser additive manufacturing

    Science.gov (United States)

    Ren, Bo; Chen, Changjun; Zhang, Min

    2018-04-01

    Stellite 6 cobalt-based alloy powder was used to produce Co-Cr-W alloy using laser additive manufacturing technology, and then different heat treatment strategies were carried out on the deposited sample. The characteristics of microstructure under different heat treatment conditions were investigated using scanning electron microscopy with energy dispersive spectroscopy, transmission electron microscope, and x-ray diffraction. The results show that the as-deposited sample has few cracks or pores, and the microstructure is typical dendritic structure, and lamellar eutectic carbides are rich in Cr in interdendritic. The matrix mainly consists of γ phases and a few ɛ phases. Some γ phases transform into ɛ phases after 900°C/6 h aging treatment and lamellar eutectic carbides transform into blocky carbides presenting as a network, most of the carbides are rich in Cr and a few are rich in W. When heat treated at 1200°C/1 h followed by water cooling and then treated at 900°C/6 h followed by furnace cooling, it can be found that some γ phases transform into ɛ phases. The carbides transform into elliptical M23C6 carbides that are rich in Cr with the size of 1 to 3 μm and a part of W-rich carbides.

  10. Effect of in-situ formed Al3Ti particles on the microstructure and mechanical properties of 6061 Al alloy

    Science.gov (United States)

    Gupta, Rahul; Chaudhari, G. P.; Daniel, B. S. S.

    2018-03-01

    In this study, in situ Titanium-tri-aluminide (Al3Ti) particles reinforced Al 6061 alloy matrix composites were fabricated by the reaction of potassium hexafluorotitanate (K2TiF6) inorganic salt with molten Al 6061 alloy via liquid metallurgy route. The development of in-situ Al3Ti particles and their effects on the mechanical properties such as yield strength (YS), ductility, ultimate tensile strength (UTS) and hardness, and microstructure of Al 6061 alloy were studied. It was observed from the results that in-situ formed Al3Ti particles were blocky in morphology whose average size was around 2.6 ± 1.1 μm. Microstructure studies showed that grain size of Al matrix was reduced due to the nucleating effect of Al3Ti particles. It was observed from the mechanical properties analysis that when the volume fraction of Al3Ti particles was increased, the hardness, UTS and YS of the composites were also increased as compared to that of Al 6061 alloy. An improvement in ductility was observed with the dispersion of Al3Ti particles in base alloy which is contrary to many other composites.

  11. Environment-oriented low-cost porous mullite ceramic membrane supports fabricated from coal gangue and bauxite.

    Science.gov (United States)

    Lü, Qikai; Dong, Xinfa; Zhu, Zhiwen; Dong, Yingchao

    2014-05-30

    Porous mullite ceramic supports for filtration membrane were successfully fabricated via recycling of coal gangue and bauxite at sintering temperatures from 1100 to 1500°C with corn starch as pore-forming agent. The dynamic sintering behaviors, phase evolution, shrinkage, porosity and pore size, gas permeation flux, microstructure and mechanical property were systematically studied. A unique volume-expansion stage was observed at increased temperatures from 1276 to 1481°C caused by a mullitization-crystal-growth process. During this stage, open porosity increases and pore size distributions broaden, which result in a maximum of nitrogen gas flux at 1400°C. The X-ray diffraction results reveal that secondary mullitization took place from 1100°C and the major phase is mullite with a content of ∼84.7wt.% at 1400°C. SEM images show that the as-fabricated mullite supports have a porous microstructure composed of sintered glassy particles embedded with inter-locked mullite crystals, which grew gradually with increasing temperature from rod-like into blocky-like morphologies. To obtain mullite membrane supports with sufficient porosity and acceptable mechanical strength, the relationship between porosity and mechanical strength was investigated, which was fitted using a parabolic equation. Copyright © 2014 Elsevier B.V. All rights reserved.

  12. Geological investigation of hydrothermal alteration haloes in Toyoha geothermal field, Hakkaido

    Energy Technology Data Exchange (ETDEWEB)

    Igarashi, T; Furukawa, Y; Sugawara, K; Nishimura, S; Okabe, K

    1978-01-01

    In Toyoha geothermal field, the altered haloes are located along a tectonic line extending on a NW-SE direction along the Yunosawa River, east of the Toyoha Mine, a well known Neogene epithermal ore deposit. The investigation was carried out to clarify the stage of alteration, based on the altered haloes geologic structure, composition, and size. The Quaternary distribution at the eastern foot of Mt. Yotei was also studied. The field is covered by various kinds of Miocene sediments but the altered haloes are found only in an area covered by the Takinosawa formation and its older formations. Among the Yunosawa, Koyanagizawa and Takinosawa alteration haloes, the Yunosawa is the most important. It is composed of blocky silicified rock extending along a river and surrounding argillaceous rock. The silicified rock is composed primarily of quartz and subordinate alunite and opal, while the argillaceous rock consists chiefly of kaloin and is characterized by the occasional presence of sericite and montmorillinite. Fission-track and /sup 14/C methods were employed to determine the stage of alteration, but the results were unsatisfactory. The sublimation sulfur ore deposits in the Yunosawa and Koyanagizawa areas were comparatively small, but their original depositional features remain intact, indicating that geothermal activity continued until recently. Yunosawa is the most promising area as it is closely related to the tectonic line and also it has extraordinarily high ground temperature determined by a recent heat flow survey. Twenty-three references are provided.

  13. Facies architecture of the Bluejacket Sandstone in the Eufaula Lake area, Oklahoma: Implications for the reservoir characterization of the Bartlesville Sandstone

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Liangmiao; Yang, Kexian [Univ. of Tulsa, OK (United States)

    1997-08-01

    Outcrop studies of the Bluejacket Sandstone (Middle Pennsylvanian) provide significant insights to reservoir architecture of the subsurface equivalent Bartlesville Sandstone. Quarry walls and road cuts in the Lake Eufaula area offer excellent exposures for detailed facies architectural investigations using high-precision surveying, photo mosaics. Directional minipermeameter measurements are being conducted. Subsurface studies include conventional logs, borehole image log, and core data. Reservoir architectures are reconstructed in four hierarchical levels: multi-storey sandstone, i.e. discrete genetic intervals; individual discrete genetic interval; facies within a discrete genetic interval; and lateral accretion bar deposits. In both outcrop and subsurface, the Bluejacket (Bartlesville) Sandstone comprises two distinctive architectures: a lower braided fluvial and an upper meandering fluvial. Braided fluvial deposits are typically 30 to 80 ft thick, and are laterally persistent filling an incised valley wider than the largest producing fields. The lower contact is irregular with local relief of 50 ft. The braided-fluvial deposits consist of 100-400-ft wide, 5-15-ft thick channel-fill elements. Each channel-fill interval is limited laterally by an erosional contact or overbank deposits, and is separated vertically by discontinuous mudstones or highly concentrated mudstone interclast lag conglomerates. Low-angle parallel-stratified or trough cross-stratified medium- to coarse-grained sandstones volumetrically dominate. This section has a blocky well log profile. Meandering fluvial deposits are typically 100 to 150 ft thick and comprise multiple discrete genetic intervals.

  14. Potential and Prospects of Continuous Polyhydroxyalkanoate (PHA Production

    Directory of Open Access Journals (Sweden)

    Martin Koller

    2015-05-01

    Full Text Available Together with other so-called “bio-plastics”, Polyhydroxyalkanoates (PHAs are expected to soon replace established polymers on the plastic market. As a prerequisite, optimized process design is needed to make PHAs attractive in terms of costs and quality. Nowadays, large-scale PHA production relies on discontinuous fed-batch cultivation in huge bioreactors. Such processes presuppose numerous shortcomings such as nonproductive time for reactor revamping, irregular product quality, limited possibility for supply of certain carbon substrates, and, most of all, insufficient productivity. Therefore, single- and multistage continuous PHA biosynthesis is increasingly investigated for production of different types of microbial PHAs; this goes for rather crystalline, thermoplastic PHA homopolyesters as well as for highly flexible PHA copolyesters, and even blocky-structured PHAs consisting of alternating soft and hard segments. Apart from enhanced productivity and constant product quality, chemostat processes can be used to elucidate kinetics of cell growth and PHA formation under constant process conditions. Furthermore, continuous enrichment processes constitute a tool to isolate novel powerful PHA-producing microbial strains adapted to special environmental conditions. The article discusses challenges, potential and case studies for continuous PHA production, and shows up new strategies to further enhance such processes economically by developing unsterile open continuous processes combined with the application of inexpensive carbon feedstocks.

  15. Synthesis and properties of Li2SnO3/polyaniline nanocomposites as negative electrode material for lithium-ion batteries

    Science.gov (United States)

    Wang, Qiufen; Huang, Ying; Miao, Juan; Zhao, Yang; Wang, Yan

    2012-10-01

    The nanocomposites Li2SnO3/polyaniline (Li2SnO3/PANI) have been synthesized by a micro emulsion polymerization method. The structure, morphology and electrochemical properties of the as-prepared materials are characterized by XRD, FTIR, Raman, XPS, TGA, TEM and electrochemical measurements. Results show that Li2SnO3/PANI nanocomposites are composed of uniform and blocky nano-sized particles (40-50 nm) with clear lattice fringes. Electrochemical measurement suggests that Li2SnO3/PANI exhibits better cycling properties and lower initial irreversible capacities than Li2SnO3 as negative electrodes materials for lithium-ion batteries. At a current density of 60 mA g-1 in the voltage about 0.05-2.0 V, the initial irreversible capacity of Li2SnO3/PANI is 563 mAh g-1 while it is 687.5 mAh g-1 to Li2SnO3. The capacity retained of Li2SnO3/PANI (569.2 mAh g-1) is higher than that of Li2SnO3 (510.2 mAh g-1) after 50 cycles. The PANI in the Li2SnO3/PANI nanocomposites can buffer the released stress caused by the drastic volume variation during the alloying/de-alloying process of Li-Sn.

  16. Microstructure evolution of Fe-based nanostructured bainite coating by laser cladding

    International Nuclear Information System (INIS)

    Guo, Yanbing; Li, Zhuguo; Yao, Chengwu; Zhang, Ke; Lu, Fenggui; Feng, Kai; Huang, Jian; Wang, Min; Wu, Yixiong

    2014-01-01

    Highlights: • The laser cladding and isothermal holding are used to fabricate nanobainite coating. • Fine prior austenite is obtained to accelerate the bainite transformation. • Low transformation temperature results in fine bainite ferrite and film austenite. • Retained austenite volume fraction in bainite coating is determined by XRD. • Evolution of carbon content in austenite and ferrite is analyzed. - Abstract: A Fe-based coating with nano-scale bainitic microstructure was fabricated using laser cladding and subsequent isothermal heat treatment. The microstructure of the coating was observed and analyzed using optical microscope (OM), field-emission scanning electron microscope (FE-SEM), transmission electron microscope (TEM) and X-ray diffraction (XRD). The results showed that nanostructured bainitic ferrite and carbon-enriched retained austenite distributed uniformly in the coating. Blocky retained austenite was confined to the prior austenite grain boundaries resulting from the elements segregation. The bainitic microstructure obtained at 250 °C had a finer scale compared with that obtained at 300 °C. The volume fraction of austenite increased with increasing transformation temperature for the fully transformed bainitic coating. The bainitic transformation was accelerated as a result of the fine prior austenite generated during the laser cladding. The evolution of the carbon contents in bainitic ferrite and retained austenite revealed the diffusionless mechanism of the bainitic transformation

  17. Laser cladding of in situ TiB{sub 2}/Fe composite coating on steel

    Energy Technology Data Exchange (ETDEWEB)

    Du Baoshuai; Zou Zengda [School of Materials Science and Engineering, Shandong University, Jinan 250061 (China); Wang Xinhong [School of Materials Science and Engineering, Shandong University, Jinan 250061 (China)], E-mail: xinhongwang@sdu.edu.cn; Qu Shiyao [School of Materials Science and Engineering, Shandong University, Jinan 250061 (China)

    2008-08-15

    To enhance the wear resistance of mechanical components, laser cladding has been applied to deposit in situ TiB{sub 2}/Fe composite coating on steel using ferrotitanium and ferroboron as the coating precursor. The phase constituents and microstructure of the composite coating were investigated using X-ray diffraction (XRD), scanning electron micrograph (SEM) and electron probe microanalysis (EPMA). Microhardness tester and block-on-ring wear tester were employed to measure the microhardness and dry-sliding wear resistance of the composite coating. Results show that defect-free composite coating with metallurgical joint to the steel substrate can be obtained. Phases presented in the coating consist of TiB{sub 2} and {alpha}-Fe. TiB{sub 2} particles which are formed in situ via nucleation-growth mechanism are distributed uniformly in the {alpha}-Fe matrix with blocky morphology. The microhardness and wear properties of the composite coating improved significantly in comparison to the as-received steel substrate due to the presence of the hard reinforcement TiB{sub 2}.

  18. Tardigrade eggs and exuviae in Antarctic lake sediments: insights into Holocene dynamics and origins of the fauna

    Directory of Open Access Journals (Sweden)

    Sandra J. MCINNES

    2007-09-01

    Full Text Available The preservation of tardigrade eggs and exuviae in Antarctic lake sediments provided an opportunity to assess post-glacial colonisation and Holocene tardigrade dynamics on the southern continent. Tardigrade eggs were recovered from five lakes, two from the maritime Antarctic and three from continental Antarctica. Eggs were identified from the following species: Dactylobiotus cf. ambiguus, Macrobiotus furciger, Macrobiotus blocki, Minibiotus weinerorum and Acutuncus antarcticus. Other, unornamented eggs were also observed. The preservation of some of these eggs in exuviae allowed identification to at least genus. Significant variations were observed in egg abundance within the sediment of each lake, and in one lake a species (Dactylobiotus cf. ambiguus became locally extinct, probably as the result of penguin-associated eutrophication. Tardigrades generally did not become abundant for a considerable period after the lakes’ formation. The presence of an in-part endemic fauna is consistent with slow colonisation from Antarctic sources rather than wind transport from extra-continental sites. Tardigrade eggs appear to be abundant in high-latitude lake sediments, and greater use could be made of these records when evaluating tardigrade dynamics during the Holocene.

  19. High Throughput Phenotyping of Blueberry Bush Morphological Traits Using Unmanned Aerial Systems

    Directory of Open Access Journals (Sweden)

    Aaron Patrick

    2017-12-01

    Full Text Available Phenotyping morphological traits of blueberry bushes in the field is important for selecting genotypes that are easily harvested by mechanical harvesters. Morphological data can also be used to assess the effects of crop treatments such as plant growth regulators, fertilizers, and environmental conditions. This paper investigates the feasibility and accuracy of an inexpensive unmanned aerial system in determining the morphological characteristics of blueberry bushes. Color images collected by a quadcopter are processed into three-dimensional point clouds via structure from motion algorithms. Bush height, extents, canopy area, and volume, in addition to crown diameter and width, are derived and referenced to ground truth. In an experimental farm, twenty-five bushes were imaged by a quadcopter. Height and width dimensions achieved a mean absolute error of 9.85 cm before and 5.82 cm after systematic under-estimation correction. Strong correlation was found between manual and image derived bush volumes and their traditional growth indices. Hedgerows of three Southern Highbush varieties were imaged at a commercial farm to extract five morphological features (base angle, blockiness, crown percent height, crown ratio, and vegetation ratio associated with cultivation and machine harvestability. The bushes were found to be partially separable by multivariate analysis. The methodology developed from this study is not only valuable for plant breeders to screen genotypes with bush morphological traits that are suitable for machine harvest, but can also aid producers in crop management such as pruning and plot layout organization.

  20. Effect of Pr addition on microstructure and mechanical properties of AZ61 magnesium alloy

    Directory of Open Access Journals (Sweden)

    You Zhiyong

    2014-03-01

    Full Text Available To improve the strength, hardness and heat resistance of Mg-6Al-1Zn (AZ61 alloy, the effects of Pr addition on the as-cast microstructure and mechanical properties of AZ61 alloy were investigated at room and elevated temperatures by means of Brinell hardness measurement, optical microscope (OM, scanning electron microscope (SEM, energy dispersive spectroscopy (EDS, X-ray diffractometer (XRD and DNS100 electronic universal testing machine. The results show that the microstructures of Pr-containing AZ61 alloys were refined, with primary β-Mg17Al12 phase distributed homogeneously. When the addition of Pr is up to 1.2wt.%, the β phase becomes finer, and new needle-like or short-rod shaped Al11Pr3 phase and blocky AlPr phase appear. As a result, optimal tensile properties are obtained. However, greater than 1.2wt.% Pr addition leads to poorer mechanical properties due to the aggregation of the needle-like phase and large size of grains. The present research findings provide a new way for strengthening of magnesium alloys at room and elevated temperatures, and a method of producing thermally-stable AZ61 magnesium alloy.

  1. Enhancing facial features by using clear facial features

    Science.gov (United States)

    Rofoo, Fanar Fareed Hanna

    2017-09-01

    The similarity of features between individuals of same ethnicity motivated the idea of this project. The idea of this project is to extract features of clear facial image and impose them on blurred facial image of same ethnic origin as an approach to enhance a blurred facial image. A database of clear images containing 30 individuals equally divided to five different ethnicities which were Arab, African, Chines, European and Indian. Software was built to perform pre-processing on images in order to align the features of clear and blurred images. And the idea was to extract features of clear facial image or template built from clear facial images using wavelet transformation to impose them on blurred image by using reverse wavelet. The results of this approach did not come well as all the features did not align together as in most cases the eyes were aligned but the nose or mouth were not aligned. Then we decided in the next approach to deal with features separately but in the result in some cases a blocky effect was present on features due to not having close matching features. In general the available small database did not help to achieve the goal results, because of the number of available individuals. The color information and features similarity could be more investigated to achieve better results by having larger database as well as improving the process of enhancement by the availability of closer matches in each ethnicity.

  2. High resolution orientation mapping of secondary phases in ATI 718Plus® alloy

    Directory of Open Access Journals (Sweden)

    Krakow Robert

    2014-01-01

    Full Text Available The polycrystalline superalloy ATI 718Plus ® (hereafter 718Plus has been developed to replace the established alloy Inconel 718 by offering higher temperature capability for applications in gas turbines. The alloy exhibits two secondary phases in the austenitic matrix; it is strengthened by the γ′-phase with η-phase discontinuously precipitated at the grain boundaries. It can be utilized to control grain growth during forging. Generally, hexagonal η phase has been reported to possess a defined crystallographic orientation with the matrix. However, the material studied here exhibits blocky η-phase that has been precipitated and grown during thermo-mechanical processing. Therefore a measurable change in orientation relationship is expected. The standard technique for orientation mapping is electron back-scattered diffraction with spatial resolution of 100 nm. That is insufficient for studying η-phase in 718Plus. By applying high resolution orientation mapping in the transmission electron microscope (Philips CM 300 FEGTEM equipped with a Nanomegas ASTARTM system a resolution of 3 nm was achieved. The indexed diffraction data was analysed using the Matlab Toolbox Mtex. The analysis included grain reconstruction and exclusion of low confidence measurements. The data set allows generating phase boundary maps indicating interfaces characteristics. Quantitative assessment shows that only 19% of the γ-η-interfaces fulfil the orientation relationship.

  3. Numerical investigation of the effect of the configuration of ExoMars landing platform propulsion system on the interaction of supersonic jets with the surface of Mars

    Science.gov (United States)

    Kagenov, Anuar; Glazunov, Anatoliy; Kostyushin, Kirill; Eremin, Ivan; Shuvarikov, Vladimir

    2017-10-01

    This paper presents the results of numerical investigations of the interaction with the Mars surface of four supersonic jets of ExoMars landing platform propulsion system. The cases of impingement of supersonic jets on a curved surface are considered depending on the values of propulsion system thrust. According to the results of numerical studies are obtained the values of normal stresses on the surface of Mars at altitudes of 1.0, 0.5 and 0.3 meter to the surface of the landing. To define the occurring shear stresses Mohr-Coulomb theory was used. The maximum values of shear stresses were defined for the following types of soil of Mars: drift material, crusty to cloddy material, blocky material, sand and Mojave Mars simulant. The conducted evaluations showed, regardless of the propulsion system configuration, that when the final stage of the controlled landing of the ExoMars landing platform, the erosion of the Mars regolith would be insignificant. The estimates are consistent with the available data from previous Mars missions.

  4. Nucleation and evolution of strain-induced martensitic (b.c.c.) embryos and substructure in stainless steel: a transmission electron microscope study

    International Nuclear Information System (INIS)

    Staudhammer, K.P.; Hecker, S.S.; Murr, L.E.

    1983-01-01

    The deformation of type 304 stainless steel produces a preponderance of strain-induced /chi/ (b.c.c.) martensite, which nucleates as stable embryos at micro-shear band or twin-fault intersections as proposed by Olson and Cohen. The two intersecting micro-shear bands must have a specific defect (fault-displacement) structure, and for stable martensite embryos to form requires a minimal micro-shear band thickness ranging from 50-70 A. The critical nature of nucleation is influenced by the local temperature and strain. The structure, geometry, and morphology of strain-induced martensite embryos is essentially invariant regardless of the strain rate, strain state or temperature. Larger volume fractions of martensite evolve at large strains (greater than or equal to 20%) as a result of embryo coalescence to produce a blocky-type morphology. Martensite embryos and coalesced volume elements of /chi/ are frequently characterized by an irregular non-homogeneous distribution of smaller b.c.c. regimes which result from the irregular satisfaction of the necessary and specific fault-displacement requirements within a larger intersection volume

  5. Small crater modification on Meridiani Planum and implications for erosion rates and climate change on Mars

    Science.gov (United States)

    Golombek, M.P.; Warner, N.H.; Ganti, V.; Lamb, M.P.; Parker, T.J.; Fergason, Robin L.; Sullivan, R.

    2014-01-01

    A morphometric and morphologic catalog of ~100 small craters imaged by the Opportunity rover over the 33.5 km traverse between Eagle and Endeavour craters on Meridiani Planum shows craters in six stages of degradation that range from fresh and blocky to eroded and shallow depressions ringed by planed off rim blocks. The age of each morphologic class from Mars over ~100 Myr and 3 Gyr timescales from the Amazonian and Hesperian are of order <0.01 m/Myr, which is 3–4 orders of magnitude slower than typical terrestrial rates. Erosion rates during the Middle-Late Noachian averaged over ~250 Myr, and ~700 Myr intervals are around 1 m/Myr, comparable to slow terrestrial erosion rates calculated over similar timescales. This argues for a wet climate before ~3 Ga in which liquid water was the erosional agent, followed by a dry environment dominated by slow eolian erosion.

  6. Post-igneous redistribution of components in eucrites

    Science.gov (United States)

    Phinney, W. C.; Lindstrom, D. J.; Mittlefehldt, D. W.; Martinez, R. R.

    1993-01-01

    In our analyses, we utilize a microdrilling technique that removes 40 to 100 micron diameter cores from mineral grains in thin sections analyzed by microprobe. The cores are then analyzed by INAA using the technique of Lindstrom. Three eucrites were selected for application of this analytical technique: monomict breccias Pasamonte and Stannern and unbrecciated EET90020. Pasamonte is among the most unequilibrated of the eucrites on the basis of zoning in pyroxenes and is considered to be an igneous rock not significantly affected by metamorphism. Stannern has igneous texture but its pyroxenes indicate some re-equilibration, although little, if any, recrystallization. EET90020 has a granulite texture and has been substantially recrystallized. Our sample of Pasamonte contains several clasts of different grain sizes ranging from glass to fine grained with diabasic texture containing lathy plagioclase, unexsolved pigeonite, and mesostasis. Cores were taken of the glass and from minerals and mesostases in six lithic clasts which normally allowed sampling of more than one phase per clast. Our sample of Stannern is also a breccia but with little difference in grain size between clasts and matrix. The plagioclase and pigeonite are blocky, twinned, and exsolved and coexist with a bit of mesostasis. Cores were taken of plagioclase and pigeonite with no attempt to distinguish separate clasts. EET90020 is a granular mixture of twinned plagioclase and pigeonite having rather uniform size and many triple junctions. Several cores were taken of both phases. Both clear and cloudy grains of plagioclase and pyroxene were sampled in all three eucrites.

  7. Effects of Ultra-Fast Cooling After Hot Rolling and Intercritical Treatment on Microstructure and Cryogenic Toughness of 3.5%Ni Steel

    Science.gov (United States)

    Wang, Meng; Liu, Zhenyu

    2017-07-01

    A novel process comprised of ultra-fast cooling after control rolling, intercritical quenching and tempering (UFC-LT) was applied to 3.5%Ni steel. In addition, quenching and tempering (QT) treatment was conducted in comparison. The present study focuses on the relationship between the microstructure and cryogenic toughness of 3.5%Ni steel. Results show that the microstructure of steel treated by UFC-LT consisted of tempered martensite, intercritical ferrite and two types of reversed austenite (RA) (needle shape and blocky). Compared to the QT sample, the UFC-LT sample's ultimate tensile strength decreased slightly, while its elongation increased from 32.3 to 35.7%, and its Charpy absorption energy at -135 °C increased from 112 to 237 J. The ductile-brittle transition temperature of UFC-LT sample was lower than that of the QT sample by 18 °C. The superior cryogenic toughness after UFC-LT compared to QT treatment can be attributed to the dissolution of cementite, approximately 3.0% increase in RA and the decrease in effective grain size.

  8. X-radiography of slices of the Allende Meteorite

    Science.gov (United States)

    Smith, M. J.; Anderson, J. B.; Heymann, D.

    1984-01-01

    A 2.2 kg fragment of the Allende Meteorite was derinded and sliced by bandsawing. Several X-radiographs were made of all slices. The following features are resolved: grains of blocky troilite (bright spots), troilite rimmed chondrules (bright halos), chondrules with central vugs (dim halos), white aggregates (dark patches), and dark inclusions (medium dark patches). The number of FeS grains larger than about 0.5 mm is one per 6 + or - 1 gram of this fragment. Their concentration appears to be uniform at the 1 kg weight level, but is not uniform at the 100 g level. The number of FeS rimmed chondrules is one per 10 g. Their concentration is also nonuniform at the 100 g weight level. The number of white aggregates is roughly one per 20 g. These disc shaped objects show a distinct preferred orientation of the axis orthogonal to the plane of the disc. Chondrules with central vugs are numerous. Linear and curved arrays of chondrules, up to a few cm long, were observed. An interpretation of the observed features is given.

  9. Perceptual video quality assessment in H.264 video coding standard using objective modeling.

    Science.gov (United States)

    Karthikeyan, Ramasamy; Sainarayanan, Gopalakrishnan; Deepa, Subramaniam Nachimuthu

    2014-01-01

    Since usage of digital video is wide spread nowadays, quality considerations have become essential, and industry demand for video quality measurement is rising. This proposal provides a method of perceptual quality assessment in H.264 standard encoder using objective modeling. For this purpose, quality impairments are calculated and a model is developed to compute the perceptual video quality metric based on no reference method. Because of the shuttle difference between the original video and the encoded video the quality of the encoded picture gets degraded, this quality difference is introduced by the encoding process like Intra and Inter prediction. The proposed model takes into account of the artifacts introduced by these spatial and temporal activities in the hybrid block based coding methods and an objective modeling of these artifacts into subjective quality estimation is proposed. The proposed model calculates the objective quality metric using subjective impairments; blockiness, blur and jerkiness compared to the existing bitrate only calculation defined in the ITU G 1070 model. The accuracy of the proposed perceptual video quality metrics is compared against popular full reference objective methods as defined by VQEG.

  10. A Combined First and Second Order Variational Approach for Image Reconstruction

    KAUST Repository

    Papafitsoros, K.

    2013-05-10

    In this paper we study a variational problem in the space of functions of bounded Hessian. Our model constitutes a straightforward higher-order extension of the well known ROF functional (total variation minimisation) to which we add a non-smooth second order regulariser. It combines convex functions of the total variation and the total variation of the first derivatives. In what follows, we prove existence and uniqueness of minimisers of the combined model and present the numerical solution of the corresponding discretised problem by employing the split Bregman method. The paper is furnished with applications of our model to image denoising, deblurring as well as image inpainting. The obtained numerical results are compared with results obtained from total generalised variation (TGV), infimal convolution and Euler\\'s elastica, three other state of the art higher-order models. The numerical discussion confirms that the proposed higher-order model competes with models of its kind in avoiding the creation of undesirable artifacts and blocky-like structures in the reconstructed images-a known disadvantage of the ROF model-while being simple and efficiently numerically solvable. ©Springer Science+Business Media New York 2013.

  11. Effect of silicon contents on the microstructures and mechanical properties of heat affected zones for 9Cr2WVTa steels

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jian [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Science, 110016, Shenyang (China); Key Laboratory of Nuclear Materials and Safety Assessment, Institute of Metal Research, Chinese Academy of Science, 110016, Shenyang (China); Lu, Shanping, E-mail: shplu@imr.ac.cn [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Science, 110016, Shenyang (China); Rong, Lijian [Key Laboratory of Nuclear Materials and Safety Assessment, Institute of Metal Research, Chinese Academy of Science, 110016, Shenyang (China); Li, Dianzhong [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Science, 110016, Shenyang (China)

    2016-03-15

    The weldability of 9Cr2WVTa steels with silicon content varying from 0.30 wt.% to 1.36 wt.% was studied to meet the requirement of Generation-Ⅳ nuclear reactor. Samples of enlarged HAZs were fabricated by a thermal-mechanical simulator based on the simulation and measurement of non-equilibrium phase transformation. The content of δ-ferrite in the HAZs increased with the silicon content and the peak temperature of welding thermal cycle. The impact toughness in the HAZs decreased in different degrees when the δ-ferrite exhibits stripe (lower than 4.82%) or blocky types (higher than 4.82%). Post weld heat treatment (PWHT) has a significant role on improving the toughness. Adding silicon content increased the volume of δ-ferrite and therefore, decreased the tensile strength of the HAZs for 9Cr2WVTa steels. Silicon also as solid solution strengthening element increased the tensile strength. The 9Cr2WVTa steel has good weldability when the silicon content is lower than 0.60 wt.%. - Highlights: • The weldability of 9Cr2WVTa steel with different silicon contents was studied. • The impact toughness decreased in different degrees owing to the δ-ferrite. • PWHT has a significant role on improving the impact toughness. • The 9Cr2WVTa steel with silicon content not exceeding 0.60 wt.% has good weldability.

  12. Corresponding between geothermometry based on mineral chemistry and deformation temperature for mylonitized granite of Noghan bridge (Sanandaj-Sirjan zone)

    International Nuclear Information System (INIS)

    Ataeifard, N.; Shabanian, N.; Davoudian, A.

    2016-01-01

    Noghan granitoid intrusion is located at the NW of Boin- Miandasht and lies in the Sanandaj-Sirjan structural zone (SSZ). Body shape is a stretched ellipsoid with NW-SE strike. The meta-granite body is extremely deformed and displays mylonitic structure such as lineation and foliation. Mylonitic texture is main texture but also show seriate granular and lipido-granoblastic textures. The main minerals are quartz, K-feldspar, plagioclase, Biotite and muscovite. Chlorite is an accessory mineral. The biotite is magmatic and recrystallized. The chlorites are alteration product. The geothermometry of biotites and chlorites shows the temperatures of 397-549°C and 231-252 °C that show good correlation with microstructure in the rock. Therefore, mantle microstructure including recrystallized subgrains in porphyroclast rims that result to Grain boundary migration and chessboard undulose extinction with fine blocky grains and amoeboid grain in quartz grains show formation temperature close to 500 °C. Microstructures such as undulose extinction, pressure solution and in quartz, tensile fracture and bookshelf sliding in feldspar, brittle fractures and displacement of folded pieces in biotite display that temperature is lower than 300°C.

  13. Rapid fluvial incision of a late Holocene lava flow: Insights from LiDAR, alluvial stratigraphy, and numerical modeling

    Science.gov (United States)

    Sweeney, Kristin; Roering, Joshua J.

    2016-01-01

    Volcanic eruptions fundamentally alter landscapes, paving over channels, decimating biota, and emplacing fresh, unweathered material. The fluvial incision of blocky lava flows is a geomorphic puzzle. First, high surface permeability and lack of sediment should preclude geomorphically effective surface runoff and dissection. Furthermore, past work has demonstrated the importance of extreme floods in driving incision via column toppling and plucking in columnar basalt, but it is unclear how incision occurs in systems where surface blocks are readily mobile. We examine rapid fluvial incision of the Collier lava flow, an andesitic Holocene lava flow in the High Cascades of Oregon. Since lava flow emplacement ∼1600 yr ago, White Branch Creek has incised bedrock gorges up to 8 m deep into the coherent core of the lava flow and deposited >0.2 km3 of sediment on the lava flow surface. Field observation points to a bimodal discharge regime in the channel, with evidence for both annual snowmelt runoff and outburst floods from Collier glacier, as well as historical evidence of vigorous glacial meltwater. To determine the range of discharge events capable of incision in White Branch Creek, we used a mechanistic model of fluvial abrasion. We show that the observed incision implies that moderate flows are capable of both initiating channel formation and sustaining incision. Our results have implications for the evolution of volcanic systems worldwide, where glaciation and/or mass wasting may accelerate fluvial processes by providing large amounts of sediment to otherwise porous, sediment-starved landscapes.

  14. Diagenetic history of late Oligocene-early Miocene carbonates in East Sabah, Malaysia

    Science.gov (United States)

    Zainal Abidin, N. S.; Raymond, R. R.; Bashah, N. S. I.

    2017-10-01

    Limestones are particularly susceptible to drastic early diagenesis modifications, mainly cementation and dissolution. During the early Miocene, a major tectonic deformation has caused a widespread of uplift in Sabah. This has resulted change in depositional environment from deep to shallow marine, which favours the deposition of Gomantong Limestone. This study aims to investigate the diagenetic history of Gomantong Limestone in East Sabah. Thorough understanding of the diagenetic processes may provide data to unravel the tectonic activities which affected the reservoir quality of the carbonates. Combining the data from comprehensive petrographic analysis, and Scanning Electron Microscopy (SEM) of 30 samples, two main cements type were identified. These are microcrystalline cement and Mg-calcite cement of granular and blocky mosaics which are dominantly seen in all samples. The sequence of diagenesis events are determined as (1) micritization; (2) grain scale compaction; (3) cementation (pore-filling); (4) mechanical compaction and cementation infilling fractures and (5) chemical compaction. These diagenetic events are interpreted as reflection of changes in diagenetic environment from shallow marine to deep burial. The massive cementation in the Gomantong Limestone has resulted into a poor reservoir quality.

  15. Evidence of volcanic and glacial activity in Chryse and Acidalia Planitiae, Mars

    Science.gov (United States)

    Martinez-Alonso, Sara; Mellon, Michael T.; Banks, Maria E.; Keszthelyi, Laszlo P.; McEwen, Alfred S.

    2011-01-01

    Chryse and Acidalia Planitiae show numerous examples of enigmatic landforms previously interpreted to have been influenced by a water/ice-rich geologic history. These landforms include giant polygons bounded by kilometer-scale arcuate troughs, bright pitted mounds, and mesa-like features. To investigate the significance of the last we have analyzed in detail the region between 60°N, 290°E and 10°N, 360°E utilizing HiRISE (High Resolution Imaging Science Experiment) images as well as regional-scale data for context. The mesas may be analogous to terrestrial tuyas (emergent sub-ice volcanoes), although definitive proof has not been identified. We also report on a blocky unit and associated landforms (drumlins, eskers, inverted valleys, kettle holes) consistent with ice-emplaced volcanic or volcano-sedimentary flows. The spatial association between tuya-like mesas, ice-emplaced flows, and further possible evidence of volcanism (deflated flow fronts, volcanic vents, columnar jointing, rootless cones), and an extensive fluid-rich substratum (giant polygons, bright mounds, rampart craters), allows for the possibility of glaciovolcanic activity in the region.Landforms indicative of glacial activity on Chryse/Acidalia suggest a paleoclimatic environment remarkably different from today's. Climate changes on Mars (driven by orbital/obliquity changes) or giant outflow channel activity could have resulted in ice-sheet-related landforms far from the current polar caps.

  16. Microstructure and grain refining performance of melt-spun Al-5Ti-1B master alloy

    International Nuclear Information System (INIS)

    Zhang Zhonghua; Bian Xiufang; Wang Yan; Liu Xiangfa

    2003-01-01

    In the present work, the microstructure and grain refining performance of the melt-spun Al-5Ti-1B (wt%) master alloy have been investigated, using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), differential scanning calorimetry (DSC), and grain refining tests. It has been found that the microstructure of the melt-spun Al-5Ti-1B master alloy is mainly composed of two phases: metastable, supersaturated α-Al solid solution and uniformly dispersed TiB 2 particles, quite different from that of the rod-like alloy consisting of three phases: α-Al, blocky TiAl 3 , and clusters of TiB 2 particles. Quenching temperatures and wheel speeds (cooling rates), however, have no obvious effect on the microstructure of the melt-spun Al-5Ti-1B alloy. Grain refining tests show that rapid solidification has a significant effect on the grain refining performance of Al-5Ti-1B alloy and leads to the great increase of nucleation rate of the alloy. Nevertheless, the melt-spun Al-5Ti-1B master alloy prepared at different wheel speeds and quenching temperatures possesses the similar grain refining performance. The reasons for the microstructure formation and the improvement of the grain refining performance of the melt-spun Al-5Ti-1B master alloy have been also discussed

  17. Electron microscopy investigation of the TiBAl and TiCAl grain refiner master alloys

    International Nuclear Information System (INIS)

    Cizek, P

    2006-01-01

    The present work brings a detailed statistical analysis of the microstructural characteristics and chemistry of the second phase particles present in the Al-5Ti-1B and Al- 3Ti-0.15C (wt.%) commercial grain refiner rods used in the Al casting industry. The investigation was performed using the TEM, EDS, STEM and HREM techniques. Both refiner rods contained large, blocky Al 3 Ti DO 22 particles. Borides present in the TiBAl rod, known to be main α-Al nucleation substrates, exhibited a facetted, hexagonal platelet morphology and largely represented a mixed (Ti,Al)B 2 phase, with Ti and Al contents changing continuously across the particle dimensions. There were two distinct families of small particles observed in the TiCAl rod. The coarser, facetted particles corresponded to cubic TiC crystal structure and these are believed to be major α-Al nucleation sites. The family of finer, round particles appeared to correspond to orthorhombic Al 6 Fe phase and their role in the nucleation process remains to be clarified. The results obtained may be used in optimising the grain refiner rod microstructures that would ensure improved refining performance during casting

  18. Electron microscopy investigation of the TiBAl and TiCAl grain refiner master alloys

    Energy Technology Data Exchange (ETDEWEB)

    Cizek, P [IMMPETUS, Department of Engineering Materials, University of Sheffield, Mappin Street, Sheffield S1 3JD (United Kingdom)

    2006-02-22

    The present work brings a detailed statistical analysis of the microstructural characteristics and chemistry of the second phase particles present in the Al-5Ti-1B and Al- 3Ti-0.15C (wt.%) commercial grain refiner rods used in the Al casting industry. The investigation was performed using the TEM, EDS, STEM and HREM techniques. Both refiner rods contained large, blocky Al{sub 3}Ti DO{sub 22} particles. Borides present in the TiBAl rod, known to be main {alpha}-Al nucleation substrates, exhibited a facetted, hexagonal platelet morphology and largely represented a mixed (Ti,Al)B{sub 2} phase, with Ti and Al contents changing continuously across the particle dimensions. There were two distinct families of small particles observed in the TiCAl rod. The coarser, facetted particles corresponded to cubic TiC crystal structure and these are believed to be major {alpha}-Al nucleation sites. The family of finer, round particles appeared to correspond to orthorhombic Al{sub 6}Fe phase and their role in the nucleation process remains to be clarified. The results obtained may be used in optimising the grain refiner rod microstructures that would ensure improved refining performance during casting.

  19. Numerical modelling of convective heat transport by air flow in permafrost talus slopes

    Directory of Open Access Journals (Sweden)

    J. Wicky

    2017-06-01

    Full Text Available Talus slopes are a widespread geomorphic feature in the Alps. Due to their high porosity a gravity-driven internal air circulation can be established which is forced by the gradient between external (air and internal (talus temperature. The thermal regime is different from the surrounding environment, leading to the occurrence of permafrost below the typical permafrost zone. This phenomenon has mainly been analysed by field studies and only few explicit numerical modelling studies exist. Numerical simulations of permafrost sometimes use parameterisations for the effects of convection but mostly neglect the influence of convective heat transfer in air on the thermal regime. In contrast, in civil engineering many studies have been carried out to investigate the thermal behaviour of blocky layers and to improve their passive cooling effect. The present study further develops and applies these concepts to model heat transfer in air flows in a natural-scale talus slope. Modelling results show that convective heat transfer has the potential to develop a significant temperature difference between the lower and the upper parts of the talus slope. A seasonally alternating chimney-effect type of circulation develops. Modelling results also show that this convective heat transfer leads to the formation of a cold reservoir in the lower part of the talus slope, which can be crucial for maintaining the frozen ground conditions despite increasing air temperatures caused by climate change.

  20. Evaluation of the Sensitization of 316L Stainless Steels After the Post Weld Heat Treatment

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Junho; Jang, Changheui [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Lee, Kyoung Soo [Korea Hydro and Nuclear Power Co. Ltd., Daejeon (Korea, Republic of)

    2014-05-15

    It was observed that the PWSCC growth rate of alloy 182 was markedly decreased after PWHT. However, the PWHT of components made of stainless steels (SSs) would be limited because of the concerns about sensitization when they are exposed to temperature range of 500 to 800 .deg. C. Also, the sensitization of austenitic stainless steels could increase the susceptibility to intergrannular stress corrosion cracking. Therefore, the effect of PWHT on the sensitization behaviors of 316L SSs having predominant austenitic structure with small amount of ferrite was investigated to assess the applicability of PWHT to dissimilar weld area with austenitic stainless steels. The sensitization behaviors of two heats of 316L SSs with small amount of ferrite were investigated after heat treatment at 600, 650 and 700 .deg. C. Grain boundary sensitization was not observed in 316L SSs after the heat treatment at 600, 650 and 700 .deg. C up to 30 h. The increase in degree of sensitization (DOS) was caused by reduction of corrosion resistance in ferrite phase due to formation of chromium carbide and intermatallic phases during heat treatment. The DOS value of 316L SSs depended on the ferrite morphology. The stringer type of ferrite (316L-heat A) showed relatively higher DOS in comparison with 316L containing blocky type of ferrite (316L-heat B). It could be due to sufficient supplement of chromium in larger size of ferrite phase.

  1. Evaluation of the Sensitization of 316L Stainless Steels After the Post Weld Heat Treatment

    International Nuclear Information System (INIS)

    Lee, Junho; Jang, Changheui; Lee, Kyoung Soo

    2014-01-01

    It was observed that the PWSCC growth rate of alloy 182 was markedly decreased after PWHT. However, the PWHT of components made of stainless steels (SSs) would be limited because of the concerns about sensitization when they are exposed to temperature range of 500 to 800 .deg. C. Also, the sensitization of austenitic stainless steels could increase the susceptibility to intergrannular stress corrosion cracking. Therefore, the effect of PWHT on the sensitization behaviors of 316L SSs having predominant austenitic structure with small amount of ferrite was investigated to assess the applicability of PWHT to dissimilar weld area with austenitic stainless steels. The sensitization behaviors of two heats of 316L SSs with small amount of ferrite were investigated after heat treatment at 600, 650 and 700 .deg. C. Grain boundary sensitization was not observed in 316L SSs after the heat treatment at 600, 650 and 700 .deg. C up to 30 h. The increase in degree of sensitization (DOS) was caused by reduction of corrosion resistance in ferrite phase due to formation of chromium carbide and intermatallic phases during heat treatment. The DOS value of 316L SSs depended on the ferrite morphology. The stringer type of ferrite (316L-heat A) showed relatively higher DOS in comparison with 316L containing blocky type of ferrite (316L-heat B). It could be due to sufficient supplement of chromium in larger size of ferrite phase

  2. Microstructure and hydrothermal corrosion behavior of NITE-SiC with various sintering additives in LWR coolant environments

    Energy Technology Data Exchange (ETDEWEB)

    Parish, Chad M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, Kurt A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kim, Young -Jin [GE Global Research Center, Schenectady, NY (United States); Koyanagi, Takaaki [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Katoh, Yutai [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-11-28

    Nano-infiltration and transient eutectic phase (NITE) sintering was developed for fabrication of nuclear grade SiC composites. We produced monolithic SiC ceramics using NITE sintering, as candidates for accident-tolerant fuels in light-water reactors (LWRs). In this work, we exposed three different NITE chemistries (yttria-alumina [YA], ceria-zirconia-alumina [CZA], and yttria-zirconia-alumina [YZA]) to autoclave conditions simulating LWR coolant loops. The YZA was most corrosion resistant, followed by CZA, with YA being worst. High-resolution elemental analysis using scanning transmission electron microscopy (STEM) X-ray mapping combined with multivariate statistical analysis (MVSA) datamining helped explain the differences in corrosion. YA-NITE lost all Al from the corroded region and the ytttria reformed into blocky precipitates. The CZA material lost all Al from the corroded area, and the YZA – which suffered the least corrosion –retained some Al in the corroded region. Lastly, the results indicate that the YZA-NITE SiC is most resistant to hydrothermal corrosion in the LWR environment.

  3. Calidad de Andosols en sistemas forestal, agroforestal y agrícola con diferentes manejos en Zacatlán, Puebla

    Directory of Open Access Journals (Sweden)

    Jonathan Omar Hernández Ordoñez

    2017-04-01

    Full Text Available Los estudios de suelos en sistemas agroforestales relacionados con bosques mesófilos de montaña han sido poco abordados en nuestro país, especialmente los desarrollados en Andosols, los cuales son susceptibles a los procesos de degradación por el cambio de uso del suelo. El presente estudio se realizó en el municipio de Zacatlán, Puebla con el objetivo de caracterizar la calidad de los Andosols bajo diferentes sistemas de manejo. Los métodos que se emplearon fueron: entrevistas a productores para identificar los sistemas, descripción de perfiles de suelos, análisis de laboratorio y análisis de similaridad de los diferentes manejos. Los resultados indicaron que la zona de estudio está integrada por tres sistemas: bosque mesófilo de Montaña (BMM, agroforestal (asociaciones manzana-maíz-calabaza-arándanos y agrícola, con adición de abonos orgánicos (FO o fertilización inorgánica (FI. En los Andosols con BMM, la estructura biológica domina (agregados migajosos y granulares hasta los 55 cm de profundidad, presentan alto contenido de materia orgánica del suelo (MOS (31%, alta retención de humedad (194.5% y baja densidad aparente (Da (0.49 g cm-3. Con el cambio de uso de suelo (de bosque a agroforestal o agrícola, la estructura biológica se reduce en espesor o desaparece y dominan los bloques sub-angulares, debido a la disminución drástica del contenido de MOS (a 16.3 o a 6.3%, y retención de humedad (de 97 o a 47%. Además, la Da aumentó hasta 1 g cm-3 en el sistema agrícola. Por el contrario, en tierras degradadas, el sistema agroforestal con manejo orgánico ha mejorado la calidad del horizonte superficial en menos de seis años y con la FO o FI algunos sistemas agroforestales aumentaron los contenidos de Ntot y P. Los índices que mejor caracterizaron la calidad de los Andosols bajo diferentes sistemas fueron: estructura del suelo, MOS, Ntot, P y retención de humedad.

  4. Resetting of Quartz OSL (optically stimulated luminescence) Signals by Frictional Heating in Experimentally Sheared Gouges at Seismic Slip Rates.

    Science.gov (United States)

    Kim, J. H.; Choi, J. H.; Chauhan, N.; Lee, S.; Hirose, T.; Ree, J. H.

    2014-12-01

    Recent studies on natural and experimental seismic faults have revealed that frictional heating plays an important role in earthquake dynamics as well as in producing mineralogical and microstructural signatures of seismic faulting. Here, we report changes in OSL signals in quartz by frictional heating in experimental fault gouges. The gouges (80% of quartz and 20% of bentonite by weight) with a thickness of 1 mm were sheared between sandstone cylinders (diameter: 25 mm) at a normal stress of 1 MPa and slip rate of 1.31 m/s. The quartz grains from a sand dune on the western coast of South Korea were sieved to select size fractions between 90 and 250 μm. The equivalent dose (De) of the undeformed quartz grains was 8.0 ± 0.3 Gy. Upon displacement, the friction abruptly increases to the 1st peak (with friction coefficient μ ≈ 0.75) followed by slip weakening. Then the fault zones show two more peak frictions (μ ≈ 0.53~0.75) and finally reach a steady-state friction (μ ≈ 0.2~0.35). The fault can be divided into three zones based grain size (thus slip rate); slip localization (SLZ), intermediate slip-rate (ISZ) and low slip-rate (LSZ) zones. SLZ develops adjacent to the moving side of the sandstone cylinder with P-foliation and shear band. The size of quartz (Dq) in ISZ and LSZ is 5-30 μm and 50-250 μm, respectively. SEM and TEM analyses indicate that the fault gouge of SLZ consists of subangular quartz clasts (Dq ≈ 3 μm) and matrix of nano-scale quartz, unidentified silicate minerals and amorphous material. The fault zones were sectioned into six layers (~160 µm thick for each layer) parallel to the fault zone boundary for OSL analyses. Quartz grains from all the layers except the one immediately adjacent to the stationary side of the sandstone cylinder show De of 'effectively' 0 Gy indicating a full resetting of OSL signals. The partial resetting of OSL signal in the layer adjacent to the stationary side of the cylinder indicates the temperature (T

  5. Buried Wetlands: The Origin and Evolution of Pre-Settlement Piedmont Valley Bottoms in Pennsylvania and Maryland

    Science.gov (United States)

    Walter, R. C.; Merritts, D. J.; Voli, M. T.; Scheid, C. R.; Hartranft, J. L.; Hilgartner, W. B.; Rahnis, M. A.

    2008-12-01

    In Walter and Merritts (2008) we describe the stratigraphy of Mid-Atlantic Piedmont stream banks to consist of 1-5 m stacks of post-settlement fine-grained sediments overlying a thin organic-rich horizon, which in turn overlies a veneer of gravels on bedrock. We attribute the widespread deposition of the fine-grained sediments to an increase in base level caused by the construction of Early American milldams that lined valley bottoms by the mid 19th Century, and to the filling of extensive millponds with eroded upland soil. Several earlier researchers noted the existence of a dark organic-rich horizon near the base of stream banks in this region, but little attention was paid to their nature or origin. Our studies show that this dark layer formed during the Holocene, and was hydro-climatically stable for at least the last 5,000 yrs. Analyses of extracted seeds reveal obligate and facultative wetland plants, indicating that this horizon should be classified as a hydric (wetland) soil. Trenches and bank exposures show that this wetland soil can be traced across valley bottoms where it overlies coarse, generally quartz-rich gravels that are angular to subangular except where underlain by bedrock composed of rounded gravels. We interpret these basal gravels to be a concentrated lag from denudation of adjacent hillslopes over millions of years, and in places this lag was reworked by periglacial processes. The angularity of the clasts and the lack of fluvial depositional structures indicate that the basal gravels were not transported or deposited by river action. We have found no evidence of a pre-settlement stream channel form in the 1st to 3rd order streams of the 20+ watersheds we have studied to date. The widespread occurrence of hydric soils and the lack of discernable pre-settlement stream channels indicate that valley bottoms were dominated by broad wetland ecosystems. Given that state and federal agencies are spending millions of dollars to create new wetlands

  6. Stratigraphic reconstruction of two debris avalanche deposits at Colima Volcano (Mexico): Insights into pre-failure conditions and climate influence

    Science.gov (United States)

    Roverato, M.; Capra, L.; Sulpizio, R.; Norini, G.

    2011-10-01

    Throughout its history, Colima Volcano has experienced numerous partial edifice collapses with associated emplacement of debris avalanche deposits of contrasting volume, morphology and texture. A detailed stratigraphic study in the south-eastern sector of the volcano allowed the recognition of two debris avalanche deposits, named San Marcos (> 28,000 cal yr BP, V = ~ 1.3 km 3) and Tonila (15,000-16,000 cal yr BP, V = ~ 1 km 3 ). This work sheds light on the pre-failure conditions of the volcano based primarily on a detailed textural study of debris avalanche deposits and their associated pyroclastic and volcaniclastic successions. Furthermore, we show how the climate at the time of the Tonila collapse influenced the failure mechanisms. The > 28,000 cal yr BP San Marcos collapse was promoted by edifice steep flanks and ongoing tectonic and volcanotectonic deformation, and was followed by a magmatic eruption that emplaced pyroclastic flow deposits. In contrast, the Tonila failure occurred just after the Last Glacial Maximum (22,000-18,000 cal BP) and, in addition to the typical debris avalanche textural characteristics (angular to sub-angular clasts, coarse matrix, jigsaw fit) it shows a hybrid facies characterized by debris avalanche blocks embedded in a finer, homogenous and partially cemented matrix, a texture more characteristic of debris flow deposits. The Tonila debris avalanche is directly overlain by a 7-m thick hydromagmatic pyroclastic succession. Massive debris flow deposits, often more than 10 m thick and containing large amounts of tree trunk logs, represent the top unit in the succession. Fluvial deposits also occur throughout all successions; these represent periods of highly localized stream reworking. All these lines of evidence point to the presence of water in the edifice prior to the Tonila failure, suggesting it may have been a weakening factor. The Tonila failure appears to represent an anomalous event related to the particular climatic

  7. Early Depositional History of the Eocene Izu-Bonin Mariana Arc, Western Pacific Ocean

    Science.gov (United States)

    Waldman, R.; Marsaglia, K. M.; Tepley, F. J., III

    2015-12-01

    Expedition 351 of the International Ocean Discovery Program cored an Eocene section at Site U1438 in the Philippine Sea that provides insight into the early history of the Izu-Bonin arc. Subduction here is hypothesized to have initiated spontaneously, leaving a characteristic depositional sequence of post-subduction-initiation localized extension and volcanism. We conducted detailed macroscopic and microscopic study of the cores of the lowermost 100m of volcaniclastic and sedimentary rocks (Unit IV) directly overlying subduction initiation igneous basement, to identify depositional facies and trends. We subdivided Unit IV into three subunits based on lithologic characteristics. Transitions between the subunits are relatively abrupt, occurring within the length of a single core. The lowermost subunit (IVA) consists of 4 meters of laminated pelagic claystone with thin beds of graded volcaniclastic siltstone, and fine-grained tuff laminae composed of plagioclase feldspar and green-brown amphibole. The middle subunit (IVB) comprises 51 meters of texturally variable, thick-bedded, coarse-grained gravity flow deposits. These are composed of volcaniclastic sandstone and conglomerate containing glassy and tachylitic volcanic grains as well as sedimentary lithic fragments, along with traces of shallow-water carbonate bioclasts. Subunit IVB sediments are poorer in feldspar than IVA and contain only trace amphibole. They show variable grain rounding and an upsection increase in vitric components. Tachylite grains range from sub-angular to well rounded throughout, and other volcanic grain types show upward increases in angularity and vesicularity. The abrupt transition from pelagic sediments in subunit IVA to shallow-water-sourced gravity flows in subunit IVB suggests a rapid emergence of shallow-water to subaerial volcanic center early in the arc's development. The upper part of subunit IVB also contains igneous intrusions, providing possible evidence for more proximal

  8. Sedimentation in a Submarine Seamount Apron at Site U1431, International Ocean Discovery Program Expedition 349, South China Sea

    Science.gov (United States)

    Dadd, K. A.; Clift, P. D.; Hyun, S.; Jiang, T.; Liu, Z.

    2014-12-01

    International Ocean Discovery Program (IODP) Expedition 349 Site U1431 is located near the relict spreading ridge in the East Subbasin of the South China Sea. Holes at this site were drilled close to seamounts and intersected the volcaniclastic apron. Volcaniclastic breccia and sandstone at Site U1431 are dated as late middle Miocene to early late Miocene (~8-13 Ma), suggesting a 5 m.y. duration of seamount volcanism. The apron is approximately 200 m thick and is sandwiched between non-volcaniclastic units that represent the background sedimentation. These comprise dark greenish gray clay, silt, and nannofossil ooze interpreted as turbidite and hemipelagic deposits that accumulated at abyssal water depths. At its base, the seamount sequence begins with dark greenish gray sandstone, siltstone, and claystone in upward fining sequences interpreted as turbidites intercalated with minor intervals of volcaniclastic breccia. Upsection the number and thickness of breccia layers increases with some beds up to 4.8 m and possibly 14.5 m thick. The breccia is typically massive, ungraded, and poorly sorted with angular to subangular basaltic clasts, as well as minor reworked subrounded calcareous mudstone, mudstone, and sandstone clasts. Basaltic clasts include nonvesicular aphyric basalt, sparsely vesicular aphyric basalt, highly vesicular aphyric basalt, and nonvesicular glassy basalt. Mudstone clasts are clay rich and contain foraminifer fossils. The matrix comprises up to 40% of the breccia beds and is a mix of clay, finer grained altered basalt clasts, and mafic vitroclasts with rare foraminifer fossils. Some layers have calcite cement between clasts. Volcaniclastic sandstone and claystone cycles interbedded with the breccia layers have current ripples and parallel laminations indicative of high-energy flow conditions during sedimentation. The breccia beds were most likely deposited as a series of debris flows or grain flows. This interpretation is supported by their

  9. Geology and environments of subglacial Lake Vostok.

    Science.gov (United States)

    Leitchenkov, German L; Antonov, Anton V; Luneov, Pavel I; Lipenkov, Vladimir Ya

    2016-01-28

    The reconstruction of the geological (tectonic) structure and environments of subglacial Lake Vostok is based on geophysical surveys and the study of mineral particles found in cores of accreted ice and frozen lake water (sampled after the lake was unsealed). Seismic reflection and refraction investigations conducted in the southern part of Lake Vostok show very thin (200-300 m) sedimentary cover overlying a crystalline basement. Most of this thin veneer is thought to have been deposited during temperate-glacial conditions in Oligocene to Middle Miocene time (ca 34-14 Ma). The composition of the lake-bottom sediments can be deduced from mineral inclusions found in cores of accreted ice. Inclusions are represented by soft aggregates consisting mainly of clay-mica minerals and micrometre-sized quartz grains. Some of these inclusions contain subangular to semi-rounded rock clasts (siltstones and sandstones) ranging from 0.3 to 8 mm in size. In total, 31 zircon grains have been identified in two rock clasts and dated using SHRIMP-II. The ages of the studied zircons range from 0.6 to 2.0 Ga with two distinct clusters between 0.8 and 1.15 Ga and between 1.6 and 1.8 Ga. Rock clasts obviously came from the western lake shore, which is thus composed of terrigenous strata with an age of not older than 600 Ma. The sedimentary nature of the western lake shore is also confirmed by seismic refraction data showing seismic velocities there of 5.4-5.5 km s(-1) at the bedrock surface. After Lake Vostok was unsealed, its water (frozen and sampled next season) was also studied with scanning electron microscopy and X-ray microprobe analysis. This study showed the existence of calcium carbonate and silica microparticles (10-20 μm across) in frozen water. © 2015 The Author(s).

  10. Sedimentology and Reservoir Characteristics of Early Cretaceous Fluvio-Deltaic and Lacustrine Deposits, Upper Abu Gabra Formation, Sufyan Sub-basin, Muglad Rift Basin, Sudan

    Science.gov (United States)

    Yassin, Mohamed; Abdullatif, Osman; Hariri, Mustafa

    2017-04-01

    Sufyan Sub-basin is an East-West trending Sub-basin located in the northwestern part of the Muglad Basin (Sudan), in the eastern extension of the West and Central Africa Rift System (WCARS). The Early Cretaceous Abu Gabra Formation considered as the main source rock in the Muglad Basin. In Sufyan Sub-basin the Early Cretaceous Upper Abu Gabra Formation is the main oil-producing reservoir. It is dominated by sandstone and shales deposited in fluvio-deltaic and lacustrine environment during the first rift cycle in the basin. Depositional and post-depositional processes highly influenced the reservoir quality and architecture. This study investigates different scales of reservoir heterogeneities from macro to micro scale. Subsurface facies analysis was analyzed based on the description of six conventional cores from two wells. Approaches include well log analysis, thin sections and scanning electron microscope (SEM) investigations, grain-size, and X-ray diffraction (XRD) analysis of the Abu Gabra sandstone. The cores and well logs analyses revealed six lithofacies representing fluvio-deltaic and lacustrine depositional environment. The sandstone is medium to coarse-grained, poorly to moderately sorted and sub-angular to subrounded, Sub-feldspathic arenite to quartz arenite. On macro-scale, reservoir quality varies within Abu Gabra reservoir where it shows progressive coarsening upward tendencies with different degrees of connectivity. The upper part of the reservoir showed well connected and amalgamated sandstone bodies, the middle to lower parts, however, have moderate to low sandstone bodies' connectivity and amalgamation. On micro-scale, sandstone reservoir quality is directly affected by textures and diagenesis.The XRD and SEM analyses show that kaolinite and chlorite clay are the common clay minerals in the studied samples. Clay matrix and quartz overgrowth have significantly reduced the reservoir porosity and permeability, while the dissolution of feldspars

  11. Understanding the mechanical and acoustical characteristics of sand aggregates compacting under triaxial conditions

    Science.gov (United States)

    Hangx, Suzanne; Brantut, Nicolas

    2016-04-01

    Mechanisms such as grain rearrangement, coupled with elastic deformation, grain breakage, grain rearrangement, grain rotation, and intergranular sliding, play a key role in determining porosity and permeability reduction during burial of clastic sediments. Similarly, in poorly consolidated, highly porous sands and sandstones, grain rotation, intergranular sliding, grain failure, and pore collapse often lead to significant reduction in porosity through the development of compaction bands, with the reduced porosity and permeability of such bands producing natural barriers to flow within reservoir rocks. Such time-independent compaction processes operating in highly porous water- and hydrocarbon-bearing clastic reservoirs can exert important controls on production-related reservoir deformation, subsidence, and induced seismicity. We performed triaxial compression experiments on sand aggregates consisting of well-rounded Ottawa sand (d = 300-400 μm; φ = 36.1-36.4%) at room temperature, to systematically investigate the effect of confining pressure (Pceff = 5-100 MPa), strain rate (10-6-10-4 s-1) and chemical environment (decane vs. water; Pf = 5 MPa) on compaction. For a limited number of experiments grain size distribution (d = 180-500 μm) and grain shape (subangular Beaujean sand; d = 180-300 μm) were varied to study their effect. Acoustic emission statistics and location, combined with microstructural and grain size analysis, were used to verify the operating microphysical compaction mechanisms. All tests showed significant pre-compaction during the initial hydrostatic (set-up) phase, with quasi-elastic loading behaviour accompanied by permanent deformation during the differential loading stage. This permanent volumetric strain involved elastic grain contact distortion, particle rearrangement, and grain failure. From the acoustic data and grain size analysis, it was evident that at low confining pressure grain rearrangement controlled compaction, with grain

  12. Anti-aging Friction of Carbonate Fault Mirror and its Microstructural Interpretation

    Science.gov (United States)

    Park, Y.; Ree, J. H.; Hirose, T.

    2017-12-01

    In our slide-hold-slide (SHS) friction tests on carbonate fault rocks, fault mirror (FM), light reflective mirror-like fault surface, shows almost zero or slightly negative aging rate of friction (`anti-aging' friction), whereas carbonate faults without FM exhibit a positive aging rate. We analyzed microstructures from three types of carbonate faults to explore the cause of the anti-aging friction of FM. The three types of fault rocks before SHS tests were made from Carrara marble; (i) FM, (ii) crushed gouge of former FM (CF), and (iii) gouge produced by pre-shearing of Carrara marble (PR). The fault zone of FM before SHS tests consists of sintered nanograin patches smeared into negative asperities of wall rocks (thickness up to 150 μm) and a sintered gouge layer between wall rocks (thickness up to 200 μm) that is composed of tightly-packed nanograins (50-500 nm in size) with triple junctions and angular-subangular fragments (a few-100 μm) of sintered nanograin aggregates. A straight and discrete Y-shear surface defines a boundary between the gouge layer and the nanograin patches or between the layer and wall rock. CF specimens before SHS tests are composed of patches of sintered nanograins as in FM specimens and a porous gouge layer with finer nanograins (a few-20 nm in size) and angular fragments of former FM. PR specimens before SHS tests are composed of damaged wall rocks and porous gouge with finer nanograins (a few-tens of μm). After SHS tests, sintered appearance of grains within the fault zones of CF and PR indicates the increase in interparticle bonding and also in contact area by grain aggregation. In contrast, the gouge layer of FM specimens after SHS tests consists mostly of angular fragments of sintered nanograin aggregates. The angular shape of the fragments indicates little increase in bonding and contact area between the fragments. Tightly sintered nanograins in FM specimens would have a lower chemical reactivity with their size coarser and

  13. Debris-covered glaciers during the LGM and Lateglacial at the eastern margin of the Alps

    Science.gov (United States)

    Seidl, Sabrina; Reitner, Jürgen M.; Wagreich, Michael

    2013-04-01

    We present the reconstruction of paleo-glaciers in the easternmost part of the Alps (Schneeberg mountain) with the main focus on sedimentology, chronology and glacial dynamics. The area is dominantly made up of limestone bedrock and hence characterized by steep slopes and cirques. Two juvenile moraine-systems can be deciphered based on geological mapping. The major system is characterized by an up to 60 m high latero-frontal dump moraine with a prominent breach-lobe moraine in a lateral position. It is regarded to represent the Last Glacial Maximum (LGM; Würm Pleniglacial). The other system is much smaller and was formed most probably during the Würm Lateglacial. The angular to subangular shape of the clasts and the abundant boulders on top of the ridges indicate a high portion of passive (Boulton, 1978) i.e. supraglacial and englacial transport of debris before deposition.Thus the model of a debris-covered glacier is favored to explain both landforms and as well the corresponding sediment facies. For the pleniglacial moraine such an assumption is backed by a low accumulation/ablation area ratio (AAR) of around 1:1 based on the reconstruction of the equilibrium line altitude (ELA) using the maximum elevation of lateral moraines (MELM; Lichtenecker, 1938). Furthermore as there is no indication of a former glacier snout glacio-fluvial processes should have played a limited role in sediment transport into the forefield. Such setting pinpoints to very cold-arid conditions, which are as well found in paleo-climate reconstructions of the eastern foreland (Frenzel et al. 1992). Boulton, G.S., 1978: Boulder shapes and grain-size distribution of debris as indicators of transport paths through a glacier and till genesis.- Sedimentology, 25, 773-799. Lichtenecker, N.,1938. Die gegenwärtige und die eiszeitliche Schneegrenze in den Ostalpen. In: Verhandlungen der III. Internationalen Quartär - Konferenz, Vienna, 1936, 141-147. Frenzel, B., Pecsi, M. & Velichko, A. A., 1992

  14. The Silurian Hoedongri Formation in the Taebaeksan Basin of Korea Revisited: its Significance in the Tectonic Reconstruction of East Asia

    Science.gov (United States)

    Chae, S.; Hong, J.; Jung, S.; Ree, J.

    2011-12-01

    angular to subangular with coarse calcite fillings between the fragments. In other layers, mylonitic marble fragments are elongated with matrix foliation wrapping around them. These features suggest repeated cycles of plastic deformation and fracturing. Tectonic significance of this shear zone (at least 90 m thick) is not clear at present, and the regional extent and absolute age constraint of the shear zone should be clarified.

  15. Sedimentary Evolution of Marginal Ganga Foreland Basin during the Late Pleistocene

    Science.gov (United States)

    Ghosh, R.; Srivastava, P.; Shukla, U. K.

    2017-12-01

    Ganga foreland basin, an asymmetrical basin, was formed as result of plate-plate collision during middle Miocene. A major thrust event occurred during 500 ka when upper Siwalik sediments were uplifted and the modern Ganga foreland basin shifted towards craton, making a more wide and deep basin. The more distal part of this basin, south of axial river Yamuna, records fluvial sedimentary packages that helps to understand dynamics of peripheral bulge during the late Quaternary. Sedimentary architecture in conjunction with chemical index of alteration (CIA), paleocurrent direction and optically stimulated dating (OSL) from 19 stratigraphic sections helped reconstructing the variations in depositional environments vis-à-vis climate change and peripheral bulge tectonics. Three major units (i) paleosol; (ii) cratonic gravel; (iii) interfluve succession were identified. The lower unit-I showing CIA values close to 70-80 and micro-morphological features of moderately well-developed pedogenic unit that shows development of calcrete, rhizoliths, and mineralized organic matter in abundance. This is a regional paleosols unit and OSL age bracketed 200 ka. This is unconformably overlain by unit-II, a channelized gravel composed of sub-angular to sub-rounded clasts of granite, quartz, quartzite, limestone and calcrete. The gravel have low CIA value up to 55, rich in vertebrate fossil assemblages and mean paleocurrent vector direction is NE, which suggesting deposition by a fan of a river draining craton into foreland. This unit is dated between 100 ka and 54 ka. The top unit-III, interfluve succession of 10-15 m thick is composed of dark and light bands of sheet like deposit of silty clay to clayey silt comprises sand lenses of red to grey color and displaying top most OSL age is 12 ka. The basal mature paleosol signifies a humid climate developed under low subsidence rate at >100 ka. After a hiatus represented by pedogenic surface deposition of unit-II (gravel) suggests uplift

  16. Remarkably preserved tephra from the 3430 Ma Strelley Pool Formation, Western Australia: Implications for the interpretation of Precambrian microfossils

    Science.gov (United States)

    Wacey, David; Saunders, Martin; Kong, Charlie

    2018-04-01

    The ∼3430 Ma Strelley Pool Formation (SPF), Pilbara, Western Australia contains some of the most diverse microfossil evidence for early life on Earth. Here we report an assemblage of tephra (scoria, tubular pumice, plus vesicular and non-vesicular volcanic glass shards) from two stratigraphic levels in the SPF, including morphotypes that closely resemble previously described microfossils from this unit and elsewhere. Clasts of scoria are characterised by numerous spheroidal vesicles, with subordinate eye- and lens-shaped morphotypes, commonly lined with anatase (TiO2) and small amounts of organic material. Their diameters range from 5-180 μm with 80% in the 10-50 μm range. Fragments of tubular pumice are also lined with anatase + / - carbon and have tube diameters of 5-15 μm. Other volcanic ejecta particles include a multitude of sub-angular shard particles with or without vesicles, plus more rounded vase-shaped, eye-shaped, and hair-like morphologies; once again, most of these are coated by anatase + / - carbon and are several tens of micrometres in size. Many of the tephra fragments are now entirely silicified with no compositional difference between the former volcanic glass, the vesicle infill and the clast matrix. However, some examples retain a partial aluminosilicate composition, either as a vesicle infilling phase or as isolated lath-like grains within the formerly glassy groundmass. Isolated occurrences of some of these tephra morphotypes strongly resemble simple microbial morphologies including pairs and clusters of cells (cf. scoria), filamentous microbes (cf. tubular pumice) and larger sheaths/cysts (cf. sub-rounded glass shards). Furthermore, some tephra-containing clasts occur in a SPF sandstone unit that hosts previously described microfossils, while others are interbedded with chert layers from which microfossils have also been described. In light of our new volcanogenic data, we evaluate the robustness of previous microfossil evidence from the

  17. Petroliferous basin analysis in Taegu area (II)

    Energy Technology Data Exchange (ETDEWEB)

    Cheong, T J; Oh, J H; Son, J D; Bong, P Y; Lee, H Y; Ryu, B J; Son, B K; Kwon, Y I; Hwang, I G; Lee, Y J; Kim, H J [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

    1997-12-01

    Sandstones of the Sindong and Hayang groups belong to the arkose-feldspar arenite. In the Sindong Group, sandstones are dominated by quartz. In the Hayang Group, however, feldspar and tuffaceous sandstones are abundant. Sand grains are subangular to subrounded and moderately-sorted, in which the sand grains show point- and long-contact. Primary pores are filled with diagenetic minerals such as calcite, silica and authigenic clay minerals. Replacement and dissolution of calcite, and alternation of feldspar form the minor secondary pores. Reservoir quality of the sandstones is poor with less than 5% of porosity. In the study area, illite crystallinity is strongly affected by the post depositional intrusion, regardless of stratigraphic position. The burial temperature of the study area could be estimated at about 150-180 deg.C based on illite crystallinity data. In the Sindong Group, vitrinite reflectance ranges from 2.51% to 3.85% Ro and Rock-Eval Tmax ranges from 613 deg. to 711 deg.C, indicating that thermal maturity of the organic matter reached at the last stage of dry gas generation. These data also indicate that all of the transformable organic matter has been transformed into hydrocarbon and that considerable hydrocarbons could have been generated. Geophysical study on the Jinju Formation suggests that P-wave velocity of the sediments is very high and high frequency seismic source should be used to identify main depositional units. In this case, some depositional units can not be recognized, using ordinary seismic data acquisition method. In summary, the Nakdong and Jinju formations contain abundant black shales, and thermal maturity of the organic matter reached at the final stage of dry gas generation. These formations also contain thick sandstones which can act as a petroleum reservoir. However, reservoir quality of the sandstones is poor (porosity: < 5%; permeability: < 0.001 md). In these sandstones, secondary pores such as dissolution pores and

  18. Calcic soils and calcretes in the southwestern United States

    Science.gov (United States)

    Bachman, George Odell; Machette, Michael N.

    1977-01-01

    Secondary calcium carbonate of diverse origins, 'caliche' of many authors, is widespread in the southwestern United States. 'Caliche' includes various carbonates such as calcic soils and products of groundwater cementation. The term 'caliche' is generally avoided in this report in favor of such terms as calcrete, calcic soils, and pervasively cemented deposits. Criteria for the recognition of various types of calcrete of diverse origins include field relations and laboratory data. Calcic soils provide a comprehensive set of characteristics that aid in their recognition in the field. These characteristics include a distinctive morphology that is zoned horizontally and can frequently be traced over tens to hundreds of square kilometers. The major process in the formation of pedogenic calcrete and calic soils is the leaching of calcium carbonate from upper soil horizons by downward percolating soil solutions and reprecipitation of the carbonate in alluvial horizons near the base of the soil profile. The formation of pedogenic calcrete involves many factors including climate, source of carbonate, and tectonic stability of the geomorphic surface on which the calcrete is deposited. Most of the carbonate in pedogenic calcrete is probably derived from windblown sand, dust, and rain. Calcic soils and pedogenic calcretes follow a six-stage sequence morphologic development and is based on a classification devised by Gile, Peterson and Grossman in 1966. The .six morphologic stages of carbonate deposition in soils are related to the relative age of the soil and are as follows: I. The first or youngest stage includes filamentous or faint coatings of carbonate on detrital grains. II. The second stage includes pebble coatings which are continuous; firm carbonate nodules are few to common. III. The third stage includes coalesced nodules which occur in a friable or disseminated carbonate matrix. IV. The fourth stage includes platy, firmly cemented matrix which engulfs nodules

  19. BAP, 2,4-D e ácido acetilsalicílico na indução e diferenciação de calos em anteras de Coffea arabica L BAP, 2,4-D and acetyl-salicylic acid on the callus induction and differentiation in Coffea arabica L. anthers

    Directory of Open Access Journals (Sweden)

    Adelaide Siqueira Silva

    2009-10-01

    2,4-D and ASA at 0, 8, 16, 32 or 64 mg L-1. 'Catuaí Vermelho 44' calli were subcultured on MS supplemented with different concentrations of BAP (0, 2, 4 or 8 mg L-1 and 2,4-D (0, 1, 2 or 4 mg L-1. The increase in ASA concentrations decreased the pro-embryoid formation on calli of both cultivars and only 2,4-D promoted the formation of friable calli. However, the balance of auxin and cytokinin used in this study favored the production of friable calli.

  20. Variable effects of cinder-cone eruptions on prehistoric agrarian human populations in the American southwest

    Science.gov (United States)

    Ort, Michael H.; Elson, Mark D.; Anderson, Kirk C.; Duffield, Wendell A.; Samples, Terry L.

    2008-10-01

    , about 1 km 2 of land severely affected by ballistic fall, and no significant tephra fall. The small area affected resulted in much less disruption of human activities than at Sunset Crater. Farming was still possible right up to the edge of the lava flows, which became attractive sites for settlements. Most sites along the lava flows have habitation and storage structures at the base of the flow and a series of small, apparently little-used, structures on the blocky lava flow above. These lava surface structures may have been defensive in nature. In addition, trails were constructed on the blocky lava flow surface. These trails, whose access points are difficult to recognize from below, appear to have been used for rapid movement across the flows, and may also have been defensive in nature. Spatter-agglutinate blocks containing ceramic sherds within them, similar to the maize-impressed spatter agglutinate at Sunset Crater, were made at Little Springs and carried to a nearby habitation site. In arid and semiarid lands such as northern Arizona, tephra fall is a mixed blessing. Thick cinder blankets (> 20-30 cm) render land uninhabitable, but thinner (3-8 cm) deposits can serve to conserve soil moisture, regulate soil temperature (thus lengthening the growing season), and, by lowering soil pH, provide a temporary (decades to a century or two) increase in available phosphorus, an important nutrient for growth. The mulch opened up new lands for settlement but likely only lasted for a century or two before reworking reduced its effects.

  1. Stratigraphy of Karaburun Peninsula

    Directory of Open Access Journals (Sweden)

    Burhan Erdoğan

    1990-06-01

    spanning from Early Triassic to Early Cretaceous, The Balıklıova formation of Campanian-Maastrichtian age rests unconformably, which consists of carbonate rocks and sandstones of flysch facies. The Karaburun belt with the stratigraphy outlined above is surrounded from all sides by a blocky unit which is called the Bomova melange. This blocky unit with highly sheared flysch matrix was formed in the Izmir-Ankara zone during a Maastrichtian-Danian interval. The boundary relations between the Karaburun belt and the Bomova melange indicate that the Karaburun platform was transported tectonically as a nap into the İzmir-Ankara zone during its opening. In this study, we have also found that the stratigraphy of the Karaburun belt is completely different from that of the so-called Sakarya continent, and they cannot be correlated with each other as suggested by the earlier workers.

  2. Radioisotope space power generator. Annual report, October 1978-September 1979

    International Nuclear Information System (INIS)

    Elsner, N.B.; Chin, J.; Staley, H.G.; Bass, J.C.; Morris, C.C.; Shearer, C.H.; Steeger, E.J.

    1982-03-01

    The emphasis of the Isotec Technology Program shifted from development of a Galileo generator to study of a segmented selenide element and couple technology. The goal of the FY 79 program was to determine the feasibility of fabricating segmented selenide P and N elements which exploit the high thermoelectric efficiency of (Cu,Ag) 2 Se and Gd 2 Se 3 materials. A preliminary evaluation of segmented element efficiencies, material compatibilities, and fabrication abilities was used to select (Cu,Ag) 2 Se/Fe(Bi,Sb) 2 Te 3 for the P element and Gd 2 Se 3 /PbTe for the N element. The iron barrier between the (Cu,Ag) 2 Se and (Bi,Sb) 2 Te 3 prevented degradation of thermoelectric properties from copper contamination of the (Bi,Sb) 2 Te 3 . Fabrication processes for both elements were developed. Gd 2 Se 3 was friable and difficult to fabricate crack-free. It also exhibited a phase transition from cubic to orthorhombic, which increased its susceptibility to microcracking and reduced its thermoelectric efficiency. Life testing of an all-bonded couple with unsegmented (Cu,Ag) 2 Se P-type and Gd 2 Se 3 N-type elements was stopped after 3300 h in a nominal 830 0 C/390 0 C thermal gradient. The Gd 2 Se 3 leg did not show any significant degradation during the test. Examination of the hot end of the P element showed the need for a less reactive hot cap material and an improved vapor supression system. Module testing of a 1-W (Bi,Sb) 2 (Se,Te) 3 generator was performed for 5000 h with no degradation in power. High-temperature Thermid 600 adhesive curing cycles were examined, 75-mW module loading tests were performed, and diagnostic examination of RTG-2A and RTG-201 was completed

  3. Effect of Different Levels of Silymarin (Silybum marianum on Growth Rate, Carcass Variables and Liver Morphology of Broiler Chickens Contaminated with Aflatoxin B1

    Directory of Open Access Journals (Sweden)

    Fani Makki O

    2013-08-01

    Full Text Available This experiment was conducted to evaluate the ability of Silybum marianum seeds (SMS on performance, carcass variables, and liver morphology of the broiler chickens contaminated with aflatoxin B1 (AFB1. A total of 216 broiler chicks (Ross 308 were used. Birds were randomly assigned to nine treatment groups, with four replicates and six birds in each replicate. Chickens were reared on litter from 1 to 35 days of age. Treatments were (AFB1 in three levels (Zero, 250 and 500 ppb and SMS in three levels (Zero, 0.5 and 1.0 percent using factorial experiment based on completely randomized design. Feed intake at the end of the three weeks did not significantly change in comparison with the control group. With the increase in the level of (AFB1 in the diet, feed intake and body weight gain were decreased compared with the control group in week 4. Feed conversion ratio was not influenced by the treatments. In diets containing AFB1, breast muscle, carcass ratio, abdominal fat and bursal gland weight were significantly decreased (P1 alone did not affect thigh, back, neck, wings, heart, legs and spleen weights. Increasing the level of SMS in the diet alone or in combination with AFB1 resulted in significant changes in the weights of carcass and internal organs. Liver of birds fed diets containing AFB1 showed abnormal signs including enlargement, yellowish, friable and rounded shape. Liver of other treatments did not show any abnormal signs. In conclusion, these findings suggest that silymarin might be used in chickens to prevent the effects of AFB1 in contaminated feed.

  4. Polyimide Foams Offer Superior Insulation

    Science.gov (United States)

    2012-01-01

    At Langley Research Center, Erik Weiser and his colleagues in the Advanced Materials and Processing Branch were working with a new substance for fabricating composites for use in supersonic aircraft. The team, however, was experiencing some frustration. Every time they tried to create a solid composite from the polyimide (an advanced polymer) material, it bubbled and foamed. It seemed like the team had reached a dead end in their research - until they had another idea. "We said, This isn t going to work for composites, but maybe we could make a foam out of it," Weiser says. "That was kind of our eureka moment, to see if we could go in a whole other direction. And it worked." Weiser and his colleagues invented a new kind of polyimide foam insulation they named TEEK. The innovation displayed a host of advantages over existing insulation options. Compared to other commercial foams, Weiser explains, polyimide foams perform well across a broad range of temperatures, noting that the NASA TEEK foams provide effective structural insulation up to 600 F and down to cryogenic temperatures. The foam does not burn or off-gas toxic fumes, and even at -423 F - the temperature of liquid hydrogen - the material stays flexible. The inventors could produce the TEEK foam at a range of densities, from 0.5 pounds per cubic foot up to 20 pounds per cubic foot, making the foam ideal for a range of applications, including as insulation for reusable launch vehicles and for cryogenic tanks and lines. They also developed a unique, friable balloon format for manufacturing the foam, producing it as hollow microspheres that allowed the foam to be molded and then cured into any desired shape - perfect for insulating pipes of different sizes and configurations. The team s originally unplanned invention won an "R&D 100" award, and a later form of the foam, called LaRC FPF-44 (Spinoff 2009), was named "NASA Invention of the Year" in 2007.

  5. Tropical Volcanic Soils From Flores Island, Indonesia

    Directory of Open Access Journals (Sweden)

    Hikmatullah

    2010-01-01

    Full Text Available Soils that are developed intropical region with volcanic parent materials have many unique properties, and high potential for agricultural use.The purpose of this study is to characterize the soils developed on volcanic materials from Flores Island, Indonesia,and to examine if the soils meet the requirements for andic soil properties. Selected five soils profiles developed fromandesitic volcanic materials from Flores Island were studied to determine their properties. They were compared intheir physical, chemical and mineralogical characteristics according to their parent material, and climatic characteristicdifferent. The soils were developed under humid tropical climate with ustic to udic soil moisture regimes withdifferent annual rainfall. The soils developed from volcanic ash parent materials in Flores Island showed differentproperties compared to the soils derived from volcanic tuff, even though they were developed from the sameintermediary volcanic materials. The silica contents, clay mineralogy and sand fractions, were shown as the differences.The different in climatic conditions developed similar properties such as deep solum, dark color, medium texture, andvery friable soil consistency. The soils have high organic materials, slightly acid to acid, low to medium cationexchange capacity (CEC. The soils in western region have higher clay content and showing more developed than ofthe eastern region. All the profiles meet the requirements for andic soil properties, and classified as Andisols order.The composition of sand mineral was dominated by hornblende, augite, and hypersthenes with high weatherablemineral reserves, while the clay fraction was dominated by disordered kaolinite, and hydrated halloysite. The soilswere classified into subgroup as Thaptic Hapludands, Typic Hapludands, and Dystric Haplustands

  6. Development of somatic embryos for genetic transformation in Curcuma longa L. and Curcuma mangga Valeton & Zijp

    Directory of Open Access Journals (Sweden)

    Vachiraporn Pikulthong

    2016-07-01

    Full Text Available Buds from rhizomes of Curcuma longa L. variety ‘Chumphon’ and Curcuma mangga Valeton & Zijp variety ‘Phetchaburi’ were cultured on Murashige and Skoog (MS medium supplemented with 2.0 mg/L N6-benzyladenine (BA for multiple shoot induction. Their shoots were cultured on MS medium supplemented with various concentrations of one of two plant growth regulators or a combination of both—2,4-dichlorophenoxyacetic acid (2,4-D and naphthaleneacetic acid (NAA. Interestingly, the medium containing both auxins (5 mg/L 2,4-D and 5 mg/L NAA was best for somatic embryo induction after culturing for 4 weeks. Somatic embryo formation reached 87.50% for Curcuma longa and 95.83% for Curcuma mangga with a high quality of loose, friable and yellowish characters. The best conditions for the formation of shootlets occurred after transferring the somatic embryo to MS medium supplemented with 3.0 mg/L BA, 0.5 mg/L NAA and 3% maltose. The shootlets were rooted by transferring to MS medium containing 3.0 mg/L NAA. This is the first report of a complete in vitro regeneration system from somatic embryos of C. longa and C. mangga which was further used for gene manipulation in these plants. Diketide CoA synthase (DCS and curcumin synthase (CURS genes, which are the two genes involved in curcuminoid biosynthesis in turmeric, were cloned and transferred to these two species using Agrobacterium-mediated transformation. The presence of both target and marker genes, hpt, in the transformed somatic embryos was confirmed by polymerase chain reaction assay. After culturing, the transformed somatic embryos could survive for 4 weeks.

  7. Uranium ores of Kazakhstan as the most technologic source of a fissionable material

    International Nuclear Information System (INIS)

    Berikbolov, B.R.

    1999-01-01

    Kazakhstan as is known has unique deposits of uranium. Its resources composed a third part of the world resources. The most important part of resources having a practical value, is related with depression in southern regions of the Republic. By now more than 15 deposits are discovered and partially explored. These deposits from three uranium provinces - Shu-Sarysu, Syr-Darya and Ili. The ores occur in friable water-bearing sandy horizons of Cretaceous and Paleogene age between waterproof agrillaceous sediments at depth from 100 up to 600 m. Ore bodies thickness changes from 5 to 10 m at uranian average-grade 0.03-0.1 %. Width of band shaped ore bodies changes from tens meters to the one kilometers and extent changes from one kilometer up to many tens kilometers. The important feature of deposits is their suitability for development by progressive in situ leaching (ISL) method. It was demonstrated, that uranium ores are comprehensive and, that is important, a lot of commercially important elements, containing in ores, gives in to extraction at development by the ISL method. The preliminary calculation of expenditures for the extraction of useful byproducts from ordinary sulphate solution have demonstrated rather high profitableness for rhenium, scandium, selenium, rare earth even at the very low contents in solution. It was pointed out, that whole technological chain applied now at industrial scale is oriented to mono-metallic uranium ores, therefore present technology of leaching and recovery of industrial solution does not allow ti extract all valuable components containing in ores. The development of new improved technological chain. beginning with a composition of leaching out reagent and up to applying of miscellaneous sorbing materials, can create new mineral-raw base of rare and dissipated elements and to lower considerably the price of uranium mining from sandstone deposits

  8. The Effects of Cooking Process and Meat Inclusion on Pet Food Flavor and Texture Characteristics

    Directory of Open Access Journals (Sweden)

    Kadri Koppel

    2014-05-01

    Full Text Available The pet food industry is an important portion of the food and feed industries in the US. The objectives of this study were (1 to determine cooking method (baking or extrusion, meat inclusion (0 or 20%, and extrusion thermal to mechanical energy ratios (low, medium, and high effects on sensory and volatile properties of pet foods, and (2 to determine associations among sensory and volatile characteristics of baked and extruded pet foods. Descriptive sensory analysis and gas chromatography-mass spectrometry were used to analyze the pet food samples. It was found that baked samples were lighter in color (2.0–2.6 baked vs. 3.5–4.3 extruded, color intensity scale 0–15, and had lower levels of attributes that indicated rancidity (i.e., fishy flavor; 0.3–0.6 baked, 0.6–1.5 extruded, scale 0–15, whereas extruded pet foods were more cohesive in mass, more friable, hard, and crisp, but less powdery than baked samples. Fresh meat inclusion tended to decrease bitterness and increase fishy flavor and cohesiveness of pet foods. High thermal to mechanical energy ratio during extrusion resulted in less musty and more porous kibbles. The main volatile compounds included aldehydes, such as hexanal and heptanal, ketones, and alcohols. Extruded samples did not contain methylpyrazine, while baked samples did not contain 2-butyl furan. Future studies should consider evaluating the relationship between sensory results and animal palatability for these types of foods.

  9. Effect of plant growth regulators on indirect shoot organogenesis of Ficus religiosa through seedling derived petiole segments

    Directory of Open Access Journals (Sweden)

    Mohsen Hesami

    2018-06-01

    Full Text Available Ficus religiosa is known as a long-lived multipurpose forest tree. The tree plays an important role for religious, medicinal, and ornamental purposes. However, the propagation rate of Ficus religiosa is low in natural habitat so the plant tissue culture techniques are an applicable method for multiplication of this valuable medicinal plants. Thus, the aim of this study is to understand the effect of different auxin/cytokinin ratios on indirect shoot organogenesis of this plant. According to our results, the maximum callus induction frequency (100% was obtained on Murashige and Skoog (MS medium supplemented with 0.5 mg/l 2,4-dichlorophenoxyacetic acid (2,4-D plus 0.05 mg/l 6-benzylaminopurine (BAP from petiole segments. For shoot induction purpose, the yellow-brownish, friable, organogenic calli were inoculated on shoot induction medium. On MS medium supplemented with 1.5 mg/l BAP and 0.15 mg/l Indole-3-butyric acid (IBA, 96.66% of the petiole-derived calli responded with an average number of 3.56 shoots per culture. The highest root formation frequency (96.66%, root number (5.5, and root length (4.83 cm were achieved on MS medium containing 2.0 mg/l IBA plus 0.1 mg/l Naphthaleneacetic acid (NAA. The rooted shoots were successfully transferred to field condition and the substrate with the mixture of cocopeat and perlite (1:1 had the highest survival rate (96.66%. This is the first report of an effective in vitro organogenesis protocol for F. religiosa by indirect shoot organogenesis through axenic seedling derived petiole explants, which can be efficiently employed for conservation of this important medicinal plant species as well as the utilization of active biomolecules. Keywords: Callus formation, Multiplication, Acclimatization, Growth regulators ratio

  10. ( Linum usitatissimum L. cv. Modran cell suspension culture

    Directory of Open Access Journals (Sweden)

    Aleksandra Seta-Koselska

    2018-01-01

    Full Text Available Flax ( Linum usitatissimum L. is an ancient crop that is widely cultivated as a source of oil, fiber, and bioactive compounds. Flax fiber is traditionally used in textile industry, linseed oil is processed for industrial oils, paints, varnishes and bio-petroleum. Flaxseeds are also rich in α-linolenic acid and phytochemicals such as lignans. In addition to the commercial aspects, this species has been used widely and readily in biotechnological, developmental, and plant-pathogen interaction studies. Differences in the levels of endogenous hormones in various cultivars of flax significantly affected the intensity of callogenesis and determined the type and concentration of growth regulators necessary for callus production. The aim of our investigation was to optimize the culture conditions for callus formation and cell proliferation in liquid medium of the Polish cultivar of fiber flax – Modran. In the first step, 4 combinations of phytohormones in the medium were tested to obtain established callus tissue suitable for initiation of suspension culture. Next, we investigated the effect of chosen plant growth regulators on cell divisions, fresh and dry weight, and dispersal of callus cells in liquid medium. Fast growing and friable callus was obtained in a modified MS medium supplemented with 0.5 mg/l BAP and 0.1 mg/l NAA. We determined that for the initiation of cell suspension supplementation with 0.5 mg/l BAP and 0.5 mg/l NAA is optimal. The results obtained indicated that high concentration of cytokinin (BAP in liquid medium limited cell proliferation and decreased biomass formation.

  11. Callus Induction of Gendarussa (Justicia gendarussa by Various Concentration of 2,4-D, IBA, and BAP

    Directory of Open Access Journals (Sweden)

    Dwi Kusuma Wahyuni

    2017-12-01

    Full Text Available Justicia gendarussa Burm.f., a medicinal plant, is Acanthaceae that has many functions. Furthermore, the compounds in gendarussa must be produced in high quantity and quality by applying callus culture method. Accordingly, it is important to study the effects of plant growth regulators (2,4-D, IBA, and BAP on callus induction of gendarussa leaves. This research design utilized a factorial design with two factors (2,4-D and IBA: 0.5, 1, 1.5 mg/L and BAP: 0.5, 1, 1.5, 2 mg/L. The experiment consisted of 24 treatments, each of which was repeated 3 times. Observation was carried out in 6 weeks. Data on the time of callus formation, percentage of explants formed callus, and callus morphology were analyzed descriptively,while data on fresh and dry weight were analyzed by Two-Way ANOVA (α = 0.5. Interestingly, the results showed that various concentration of plant growth regulators (2,4-D, IBA, and BAP affected callus induction from leaf explants of gendarussa. We concluded that the most optimal treatment combination of concentration of plant growth regulators in inducing callus from leaf explants of gendarussa is 1.5 mg/L 2,4-D and 2 mg/L BAP with a relatively long period of callus formation at the earliest, i.e. on day 5, 2.247 g of fresh weight, 0.108 gof dry weight, white callus translucent, and friable. Moreover, the optimum treatment will be used to produce secondary metabolite and seed synthetic by cell suspension culture.

  12. Unlocking the potential of tropical root crop biotechnology in east Africa by establishing a genetic transformation platform for local farmer-preferred cassava cultivars.

    Science.gov (United States)

    Nyaboga, Evans; Njiru, Joshua; Nguu, Edward; Gruissem, Wilhelm; Vanderschuren, Herve; Tripathi, Leena

    2013-01-01

    Cassava genetic transformation capacity is still mostly restricted to advanced laboratories in the USA, Europe and China; and its implementation and maintenance in African laboratories has remained scarce. The impact of transgenic technologies for genetic improvement of cassava will depend largely on the transfer of such capabilities to researchers in Africa, where cassava has an important socioeconomic niche. A major constraint to the development of genetic transformation technologies for cassava improvement has been the lack of an efficient and robust transformation and regeneration system. Despite the success achieved in genetic modification of few cassava cultivars, including the model cultivar 60444, transgenic cassava production remains difficult for farmer-preferred cultivars. In this study, a protocol for cultivar 60444 developed at ETH Zurich was successfully implemented and optimized to establish transformation of farmer-preferred cassava cultivars popular in east Africa. The conditions for production and proliferation of friable embryogenic calli (FEC) and Agrobacterium-mediated transformation were optimized for three east African farmer-preferred cultivars (Ebwanatereka, Kibandameno and Serere). Our results demonstrated transformation efficiencies of about 14-22 independent transgenic lines per 100 mg of FEC for farmer-preferred cultivars in comparison to 28 lines per 100 mg of the model cultivar 60444. The presence, integration and expression of the transgenes were confirmed by PCR, Southern blot analysis and histochemical GUS assay. This study reports the establishment of a cassava transformation platform at International Institute of Tropical Agriculture (IITA) hosted by Biosciences eastern and central Africa (BecA) hub in Kenya and provides the basis for transferring important traits such as virus resistance and prolonged shelf-life to farmer-preferred cultivars in east Africa. We anticipate that such platform will also be instrumental to transfer

  13. Management strategies, early results, benefits, and risk factors of laparoscopic repair of perforated peptic ulcer.

    Science.gov (United States)

    Lunevicius, Raimundas; Morkevicius, Matas

    2005-10-01

    The primary goal of this study was to describe epidemiology and management strategies of the perforated duodenal ulcer, as well as the most common methods of laparoscopic perforated duodenal ulcer repair. The secondary goal was to demonstrate the value of prospective and retrospective studies regarding the early results of surgery and the risk factors. The tertiary goal was to emphasize the benefits of this operation, and the fourth goal was to clarify the possible risk factors associated with laparoscopic repair of the duodenal ulcer. The Medline/Pubmed database was used. Review was done after evaluation of 96 retrieved full-text articles. Thirteen prospective and twelve retrospective studies were selected, grouped, and summarized. The spectrum of the retrospective studies' results are as follows: median overall morbidity rate 10.5 %, median conversion rate 7%, median hospital stay 7 days, and median postoperative mortality rate 0%. The following is the spectrum of results of the prospective studies: median overall morbidity rate was slightly less (6%); the median conversion rate was higher (15%); the median hospital stay was shorter (5 days) and the postoperative mortality was higher (3%). The risk factors identified were the same. Shock, delayed presentation (> 24 hours), confounding medical condition, age > 70 years, poor laparoscopic expertise, ASA III-IV, and Boey score should be considered preoperative laparoscopic repair risk factors. Each of these factors independently should qualify as a criterion for open repair due to higher intraoperative risks as well as postoperative morbidity. Inadequate ulcer localization, large perforation size (defined by some as > 6 mm diameter, and by others as > 10 mm), and ulcers with friable edges are also considered as conversion risk factors.

  14. DEMOLISHING A COLD-WAR-ERA FULE-STORAGE BASIN SUPERSTRUCTURE LADEN WITH ASBESTOS

    International Nuclear Information System (INIS)

    LLOYD, E.R.; STEVENS, J.M.; DAGAN, E.B.; ORGILL, T.K.; GREEN, M.A.; LARSON, C.H.; ZINSLI, L.C.

    2009-01-01

    The K East (KE) Basin facilities are located near the north end of the Hanford Site's 100 K area. The facilities were built in 1950 as part of the KE Reactor complex and constructed within 400 meters of the Columbia River, which is the largest river in the Pacific Northwest and by volume the fourth largest river in the United States. The basin, located adjacent to the reactor, was used for the underwater storage of irradiated nuclear fuel discharged from the reactor. The basin was covered by a superstructure comprising steel columns and beams, concrete, and cement asbestos board (CAB) siding. The project's mission was to complete demolition of the structure over the KE Basin within six months of turnover from facility deactivation activities. The demolition project team applied open-air demolition techniques to bring the facility to slab-on-grade. Several innovative techniques were used to control contamination and maintain contamination control within the confines of the demolition exclusion zone. The techniques, which focused on a defense-in-depth approach, included spraying fixatives on interior and exterior surfaces before demolition began; applying fixatives during the demolition; misting using a fine spray of water during demolition; and demolishing the facility systematically. Another innovative approach that made demolition easier was to demolish the building with the non-friable CAB remaining in place. The CAB siding covered the exterior of the building and portions of the interior walls, and was an integral part of the multiple-layered roof. The project evaluated the risks involved in removing the CAB material in a radiologically contaminated environment and determined that radiological dose rates and exposure to radiological contamination and industrial hazards would be significantly reduced by using heavy equipment to remove the CAB during demolition. The ability to perform this demolition safely and without spreading contamination (radiological or

  15. Ontogeny and Structure of the Pericarp of Schinus terebinthifolius Raddi (Anacardiaceae

    Directory of Open Access Journals (Sweden)

    Sandra Maria Carmello-Guerreiro

    2002-03-01

    Full Text Available The fruit of Schinus terebinthifolius Raddi is a globose red drupe with friable exocarp when ripe and composed of two lignified layers: the epidermis and hypodermis. The mesocarp is parenchymatous with large secretory ducts associated with vascular bundles. In the mesocarp two regions are observed: an outer region composed of only parenchymatous cells and an inner region, bounded by one or more layers of druse-like crystals of calcium oxalate, composed of parenchymatous cells, secretory ducts and vascular bundles. The mesocarp detaches itself from the exocarp due to degeneration of the cellular layers in contact with the hypodermis. The lignified endocarp is composed of four layers: the outermost layer of polyhedral cells with prismatic crystals of calcium oxalate, and the three innermost layers of sclereids in palisade.O fruto de Schinus terebinthifolius Raddi é uma drupa vermelha, globosa, com exocarpo friável quando maduro e composto de duas camadas lignificadas: a epiderme e a hipoderme. O mesocarpo é parenquimático com grandes canais secretores associados aos feixes vasculares. No mesocarpo distinguem-se duas regiões uma externa composta apenas de células parenquimáticas e uma interna, delimitada por uma ou mais camadas de células contendo cristais de oxalato de cálcio do tipo drusa, composta de células parenquimáticas, canais secretores e feixes vasculares. O mesocarpo desprende-se do exocarpo devido à degeneração das camadas celulares em contato com a hipoderme. O endocarpo é lignificado e composto de quatro camadas: uma mais externa de células poliédricas com cristais prismáticos de oxalato de cálcio e três mais internas de esclereides em paliçada.

  16. DRI Renewable Energy Center (REC) (NV)

    Energy Technology Data Exchange (ETDEWEB)

    Hoekman, S. Kent; Broch, Broch; Robbins, Curtis; Jacobson, Roger; Turner, Robert

    2012-12-31

    The primary objective of this project was to utilize a flexible, energy-efficient facility, called the DRI Renewable Energy Experimental Facility (REEF) to support various renewable energy research and development (R&D) efforts, along with education and outreach activities. The REEF itself consists of two separate buildings: (1) a 1200-ft2 off-grid capable house and (2) a 600-ft2 workshop/garage to support larger-scale experimental work. Numerous enhancements were made to DRI's existing renewable power generation systems, and several additional components were incorporated to support operation of the REEF House. The power demands of this house are satisfied by integrating and controlling PV arrays, solar thermal systems, wind turbines, an electrolyzer for renewable hydrogen production, a gaseous-fuel internal combustion engine/generator set, and other components. Cooling needs of the REEF House are satisfied by an absorption chiller, driven by solar thermal collectors. The REEF Workshop includes a unique, solar air collector system that is integrated into the roof structure. This system provides space heating inside the Workshop, as well as a hot water supply. The Workshop houses a custom-designed process development unit (PDU) that is used to convert woody biomass into a friable, hydrophobic char that has physical and chemical properties similar to low grade coal. Besides providing sufficient space for operation of this PDU, the REEF Workshop supplies hot water that is used in the biomass treatment process. The DRI-REEF serves as a working laboratory for evaluating and optimizing the performance of renewable energy components within an integrated, residential-like setting. The modular nature of the system allows for exploring alternative configurations and control strategies. This experimental test bed is also highly valuable as an education and outreach tool both in providing an infrastructure for student research projects, and in highlighting renewable

  17. Effects of hydrolysis on solid-state relaxation and stickiness behavior of sodium caseinate-lactose powders.

    Science.gov (United States)

    Mounsey, J S; Hogan, S A; Murray, B A; O'Callaghan, D J

    2012-05-01

    Hydrolyzed or nonhydrolyzed sodium caseinate-lactose dispersions were spray dried, at a protein: lactose ratio of 0.5, to examine the effects of protein hydrolysis on relaxation behavior and stickiness of model powders. Sodium caseinate (NC) used included a nonhydrolyzed control (DH 0) and 2 hydrolyzed variants (DH 8.3 and DH 15), where DH = degree of hydrolysis (%). Prior to spray drying, apparent viscosities of liquid feeds (at 70°C) at a shear rate of 20/s were 37.6, 3.14, and 3.19 mPa·s, respectively, for DH 0, DH 8, and DH 15 dispersions. Powders containing hydrolyzed casein were more susceptible to sticking than those containing intact NC. The former had also lower bulk densities and powder particle sizes. Scanning electron microscopy showed that hydrolyzed powders had thinner particle walls and were more friable than powders containing intact NC. Secondary structure of caseinates, determined by Fourier transform infrared spectroscopy, was affected by the relative humidity of storage and the presence of lactose as co-solvent rather than its physical state. Glass transition temperatures and lactose crystallization temperatures, determined by differential scanning calorimetry were not affected by caseinate hydrolysis, although the effects of protein hydrolysis on glass-rubber transitions (T(gr)) could be determined by thermo-mechanical analysis. Powders containing hydrolyzed NC had lower T(gr) values (~30°C) following storage at a higher subcrystallization relative humidity (33%) compared with powder with nonhydrolyzed NC (T(gr) value of ~40°C), an effect that reflects more extensive plasticization of powder matrices by moisture. Results support that sodium caseinate-lactose interactions were weak but that relaxation behavior, as determined by the susceptibility of powder to sticking, was affected by hydrolysis of sodium caseinate. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  18. Torrefaction Processing for Human Solid Waste Management

    Science.gov (United States)

    Serio, Michael A.; Cosgrove, Joseph E.; Wójtowicz, Marek A.; Stapleton, Thomas J.; Nalette, Tim A.; Ewert, Michael K.; Lee, Jeffrey; Fisher, John

    2016-01-01

    This study involved a torrefaction (mild pyrolysis) processing approach that could be used to sterilize feces and produce a stable, odor-free solid product that can be stored or recycled, and also to simultaneously recover moisture. It was demonstrated that mild heating (200-250 C) in nitrogen or air was adequate for torrefaction of a fecal simulant and an analog of human solid waste (canine feces). The net result was a nearly undetectable odor (for the canine feces), complete recovery of moisture, some additional water production, a modest reduction of the dry solid mass, and the production of small amounts of gas and liquid. The liquid product is mainly water, with a small Total Organic Carbon content. The amount of solid vs gas plus liquid products can be controlled by adjusting the torrefaction conditions (final temperature, holding time), and the current work has shown that the benefits of torrefaction could be achieved in a low temperature range (< 250 C). These temperatures are compatible with the PTFE bag materials historically used by NASA for fecal waste containment and will reduce the energy consumption of the process. The solid product was a dry material that did not support bacterial growth and was hydrophobic relative to the starting material. In the case of canine feces, the solid product was a mechanically friable material that could be easily compacted to a significantly smaller volume (approx. 50%). The proposed Torrefaction Processing Unit (TPU) would be designed to be compatible with the Universal Waste Management System (UWMS), now under development by NASA. A stand-alone TPU could be used to treat the canister from the UWMS, along with other types of wet solid wastes, with either conventional or microwave heating. Over time, a more complete integration of the TPU and the UWMS could be achieved, but will require design changes in both units.

  19. Efficacy of N-acetylcysteine to reduce the effects of aflatoxin B1 intoxication in broiler chickens.

    Science.gov (United States)

    Valdivia, A G; Martínez, A; Damián, F J; Quezada, T; Ortíz, R; Martínez, C; Llamas, J; Rodríguez, M L; Yamamoto, L; Jaramillo, F; Loarca-Piña, M G; Reyes, J L

    2001-06-01

    N-acetylcysteine (NAC) has been used safely in humans and in other mammals as an antidote against several toxic and carcinogenic agents, including aflatoxin B1 (AFB1). The aim of this study was to evaluate the capability of dietary supplementation with NAC to ameliorate the effects of subacute intoxication with AFB1 in broiler chickens. One hundred twenty male Hubbard 1-d-old chickens were allocated into one of four dietary treatments: 1) control group without treatment, 2) purified AFB1 added to diet (3 mg/kg of feed) for 21 d, 3) NAC (800 mg/kg BW, daily), or 4) AFB1 plus NAC at the same doses as Groups 2 and 3. Broilers treated with AFB1 plus NAC were shown to be partially protected against deleterious effects on BW (57.8%), daily weight gain (49.1%), feed conversion index (21.4%), plasma and hepatic total protein concentration (45.2, 66.7%), plasma alanine aminotransferase (67.4%), hepatic glutathione-S-transferase (18.8%), and reduced glutathione liver concentration (75.0%). In addition, they showed less intense liver fading, friable texture, and microvesicular steatosis. In the kidney, thickening of glomerular basement membrane was also less severe in NAC+AFB1-treated chickens than in AFB1-treated chickens. Our results suggest that NAC provided protection against negative effects on performance, liver and renal damage, and biochemical alterations induced by AFB1 in broiler chickens. Effects of NAC alone on chick performance were also evaluated. Addition of NAC to diet (800 mg/kg BW) did not negatively affect feed consumption, conversion index, or serum chemistry and did not induce structural changes in the liver or kidney.

  20. EFFECT OF GAMMA IRRADIATION ON THE GROWTH AND DEVELOPMENT OF SAGO PALM (Metroxylon sagu Rottb. CALLI

    Directory of Open Access Journals (Sweden)

    Imron Riyadi

    2017-01-01

    Full Text Available The application of gamma irradiation on plant materials may increase the genetic variation of the offspring with useful traits. The experiment was conducted to determine the effect of irradiation dosage of gamma ray on growth and development of sago palm (Metroxylon sagu calli. Friable calli of sago palm derived from suspension culture were used as a material source. The primary calli were initiated from apical meristematic tissues of sago palm suckers of Alitir variety from Merauke, Papua. The treatments used were dosage of gamma ray irradiation at 0, 5, 10, 15, 20 and 25 Gy. The treated calli were then subcultured on modified Murashige and Skoog (MMS solid medium containing 3% sucrose and 0.1% activated charcoal and added with 1 mg l-1 2,4-D and 0.1 mg l-1 kinetin. The results showed that at all irradiation dosages, calli biomass increased significantly. The highest proliferation of calli biomass of 5.33 folds from the initial culture after 4 weeks was achieved at gamma irradiation of 25 Gy, whereas the lowest proliferation of calli biomass of 3.4 folds was achieved at control. The best development of embryogenic calli was obtained at 10 Gy that produced 100% somatic embryos, whereas the lowest somatic embryo formation at 0% was obtained at 0 and 25 Gy after one subculture. High response of somatic embryo induction to gamma irradiation at 10 Gy may increase production of somatic embryos. These results can be used in in vitro breeding of sago palm via mutagenesis to create new elite varieties.

  1. Releasability of asbestos fibers from weathered roof cement.

    Science.gov (United States)

    Oberta, Andrew F; Poye, Lee; Compton, Steven P

    2018-03-26

    Chrysotile asbestos fibers were added to roofing products, including roof cement, for several decades. The fibers were described as "encapsulated" and therefore incapable of being released, an assertion that is disproved by the study reported herein. Three test panels of roof cement from the original container were exposed to ambient weathering in 2015 and 2016. Two panels were then sampled using the ASTM D5755 microvacuum method. Sampling revealed a light brown sub-layer under the dark brown surface layer, both of which crumbled and became friable during sampling. Analysis of the microvacuum samples with transmission electron microscopy showed that the material on the two panels contained 4,432,000 and 3,320,000 asbestos structures per cm² with nearly all of the structures consisting of fibers less than 5 µm long. Energy dispersive spectrometry determined that none of the fibers reported were coated with asphalt. The presence of free fibers were confirmed by direct examination of the surfaces of the panels and of dust released from handling the panels via scanning electron microscopy. This study confirmed the releasability of uncoated asbestos fibers from dried roof cement that was indicated in two previous studies published in 2007 and 2010. These results suggest that the finding of the 5th Circuit Court in 1997 that uncoated airborne asbestos fibers cannot be released from roof cement, and therefore do not present a potential exposure by inhalation, was erroneous in retrospect. Theexemption of roof cement from regulation under the Occupational Safety and Health Administration Construction Industry Standard for asbestos by the Court should not be relied on by employers of workers who remove weathered asbestos-containing roof cement, and precautions should be taken against exposure to airborne asbestos fibers during this work.

  2. Mineral fibres and health

    International Nuclear Information System (INIS)

    Hoskins, J.A.

    2001-01-01

    The use of inorganic fibrous materials is a comparatively new phenomenon and was uncommon before the Industrial Revolution. Humans evolved in a comparatively fibre-free environment and consequently never fully developed the defence mechanisms needed to deal with the consequences of inhaling fibres. However, the urban environment now has an airborne fibre concentration of around 1 f.l -1 , which is a tenfold increase on the natural background. Any sample of ambient air collected indoors or outdoors will probably contain some mineral fibres, but there is little evidence that these pose any risk to human health. They come from asbestos used in brakes, glass and mineral wools used as insulation and fire proofing of buildings, gypsum from plaster and a variety of types from many sources. Few of these have the potential to do any harm. Asbestos is the only fibre of note but urban levels are insignificant compared to occupational exposures. When the health of cohorts occupationally exposed to the several types of asbestos is studied the problem can be put into perspective. Studies of workers in the chrysotile industry exposed to much higher dust levels than in a factory today show no excess lung cancer or mesothelioma. By comparison those living near crocidolite mines, let alone working in them, may develop asbestos-related disease. As always, dose is the critical factor. Chrysotile is cleared from the lungs very efficiently, only the amphiboles are well retained. The only real health problem comes from the earlier use of asbestos products that may now be old, friable and damaged and made from amphibole or mixed fibre. If though, these are still in good condition, they do not pose a health problem. Asbestos-related diseases are very rare in those not occupationally exposed. Where they exist exposure has nearly always been to crocidolite. (author)

  3. Unlocking the potential of tropical root crop biotechnology in east Africa by establishing a genetic transformation platform for local farmer-preferred cassava cultivars

    Directory of Open Access Journals (Sweden)

    Evans eNyaboga

    2013-12-01

    Full Text Available Cassava genetic transformation capacity is still mostly restricted to advanced laboratories in the USA, Europe and China; and its implementation and maintainance in African laboratories has remained scarce. The impact of transgenic technologies for genetic improvement of cassava will depend largely on the transfer of such capabilities to researchers in Africa, where cassava has an important socioeconomic niche. A major constraint to the development of genetic transformation technologies for cassava improvement has been the lack of an efficient and robust transformation and regeneration system. Despite the success achieved in genetic modification of few cassava cultivars, including the model cultivar 60444, transgenic cassava production remains difficult for farmer-preferred cultivars. In this study, a protocol for cultivar 60444 developed at ETH Zurich was successfully implemented and optimized to establish transformation of farmer-preferred cassava cultivars popular in east Africa. The conditions for production and proliferation of friable embryogenic calli (FEC and Agrobacterium-mediated transformation were optimized for three east African farmer-preferred cultivars (Ebwanatereka, Kibandameno and Serere. Our results demonstrated transformation efficiencies of about 14-22 independent transgenic lines per 100 mg of FEC for farmer-preferred cultivars in comparison to 28 lines per 100 mg of the model cultivar 60444. The presence, integration and expression of the transgenes were confirmed by PCR, Southern blot analysis and histochemical GUS assay. This study reports the establishment of a cassava transformation platform at International Institute of Tropical Agriculture (IITA hosted by Biosciences eastern and central Africa (BecA hub in Kenya and provides the basis for transferring important traits such as virus resistance and prolonged shelf-life to farmer-preferred cultivars in east Africa. We anticipate that such platform will also be

  4. First physical volcanological description of a Miocene, silicic, phreatomagmatic fall complex in the Carpatho-Pannonian Region (CPR)

    Science.gov (United States)

    Biró, Tamás; Hencz, Mátyás; Karátson, Dávid; Márton, Emő; Bradák-Hayashi, Balázs; Szalai, Zoltán

    2017-04-01

    The study reports the basic physical volcanological and stratigraphical features of a hitherto unrecognized silicic phreatomagmatic fall succession from the Bükk Foreland Volcanic Area (Hungary), known as part of the extensive Miocene ignimbrite volcanism of the northern CPR. The complex have been identified at two sites, in the vicinity of Bogács and Tibolddaróc villages. Tens of mm to several dm thick layers make up the 20 m thick entire succession. The complex could be subdivided into three eruption cycles by two, intercalated well-developed paleosoil horizons, which indicate longer repose periods. The eruption cycles consist of several individual eruptive events. The volcano-sedimentological field approach was completed by granulometrical and low field anisotropy of magnetic susceptibility (AMS) studies. Combined dry sieving and laser diffraction particle size analysis were performed to get information on median grain size (MdΦ) and sorting (σΦ) of friable layers. AMS was used to infer the emplacement processes. Based on the following features the succession is proposed to record a large-scale, silicic, phreatomagmatic fall activity: i) Presence of very fine ash and abundant ash aggregates, ii) General poor sorting, and often bimodal grain-size distributions; ii) Extremely weak magnetic fabric compared to dilute, thin pyroclastic density current deposits. On the basis of comparison of the recorded grain size characteristics with data from other silicic phretomagmatic fall deposits worldwide, several units in the succession can be considered as phreatoplinian fall deposit (sensu lato), described for the first time in the CPR.

  5. The Effects of Cooking Process and Meat Inclusion on Pet Food Flavor and Texture Characteristics

    Science.gov (United States)

    Koppel, Kadri; Gibson, Michael; Alavi, Sajid; Aldrich, Greg

    2014-01-01

    Simple Summary The results of this research indicate that processing (baked vs. extruded) plays an important role in determining pet food product texture. In addition, raw ingredients (fresh meat vs. meal-based) did not consistently affect product sensory characteristics. These results may help pet food technologists better understand factors that affect palatability. Abstract The pet food industry is an important portion of the food and feed industries in the US. The objectives of this study were (1) to determine cooking method (baking or extrusion), meat inclusion (0 or 20%), and extrusion thermal to mechanical energy ratios (low, medium, and high) effects on sensory and volatile properties of pet foods, and (2) to determine associations among sensory and volatile characteristics of baked and extruded pet foods. Descriptive sensory analysis and gas chromatography-mass spectrometry were used to analyze the pet food samples. It was found that baked samples were lighter in color (2.0–2.6 baked vs. 3.5–4.3 extruded, color intensity scale 0–15), and had lower levels of attributes that indicated rancidity (i.e., fishy flavor; 0.3–0.6 baked, 0.6–1.5 extruded, scale 0–15), whereas extruded pet foods were more cohesive in mass, more friable, hard, and crisp, but less powdery than baked samples. Fresh meat inclusion tended to decrease bitterness and increase fishy flavor and cohesiveness of pet foods. High thermal to mechanical energy ratio during extrusion resulted in less musty and more porous kibbles. The main volatile compounds included aldehydes, such as hexanal and heptanal, ketones, and alcohols. Extruded samples did not contain methylpyrazine, while baked samples did not contain 2-butyl furan. Future studies should consider evaluating the relationship between sensory results and animal palatability for these types of foods. PMID:26480040

  6. Streamlined sample cleanup using combined dispersive solid-phase extraction and in-vial filtration for analysis of pesticides and environmental pollutants in shrimp

    Energy Technology Data Exchange (ETDEWEB)

    Han, Lijun [College of Science, China Agricultural University, Beijing (China); Sapozhnikova, Yelena [U.S. Dept. of Agriculture, Agricultural Research Service, Eastern Regional Research Center, 600 East Mermaid Lane, Wyndmoor, PA 19038 (United States); Lehotay, Steven J., E-mail: Steven.Lehotay@ars.usda.gov [U.S. Dept. of Agriculture, Agricultural Research Service, Eastern Regional Research Center, 600 East Mermaid Lane, Wyndmoor, PA 19038 (United States)

    2014-05-01

    Highlights: • The first report that combines in-vial filtration and dispersive-SPE for sample cleanup. • The unique application of ammonium formate for salting-out partitioning in QuEChERS. • Evaluations of a new zirconium-based and a non-friable GCB sorbent for d-SPE cleanup. • A new analytical method for 59 pesticides and environmental pollutants in shrimp. Abstract: A new method of sample preparation was developed and is reported for the first time. The approach combines in-vial filtration with dispersive solid-phase extraction (d-SPE) in a fast and convenient cleanup of QuEChERS (quick, easy, cheap, effective, rugged, and safe) extracts. The method was applied to simultaneous analysis of 42 diverse pesticides and 17 environmental contaminants, including polycyclic aromatic hydrocarbons, polychlorinated biphenyls (PCBs), and flame retardants, in shrimp as the sample matrix. Final extracts were analyzed by both low-pressure gas chromatography – triple quadrupole tandem mass spectrometry (LPGC-MS/MS), and high-performance liquid chromatography – triple quadrupole tandem mass spectrometry (HPLC-MS/MS) to provide a wide scope of analysis for targeted analytes. During method development, several different commercial sorbents for d-SPE were investigated and compared with respect to analyte recoveries. The method was validated at 10, 50, and 100 ng g⁻¹ spiking levels (10-fold lower for PCBs), and the results for nearly all analytes were between 70 and 115% recoveries with ≤17% relative standard deviations. The method was shown to be simple, fast, and effective for multi-application analysis of chemical residues in the representative food and environmental marker matrix.

  7. Mass-like Dieulafoy's lesion associated with advanced gastric cancer at the antrum of stomach: a case report and literature review.

    Science.gov (United States)

    Huang, Hsi-Lan; Leung, Chi Yan; Cheng, Chien-Jui

    2017-10-10

    Dieulafoy's lesion, also known as a caliber-persistent artery, is a shallow, small, and rare lesion that occurs along the lesser curvature of proximal stomach. It is rare for a Dieulafoy's lesion to present as a mass-like lesion that coexists with gastric cancer. To our best knowledge, we report the first case and histopathological pictures of a mass-like Dieulafoy's lesion coexisting with advanced gastric cancer in the antrum of the stomach. A 57-year-old female presented with a 6-month history of intermittent epigastric dull pain and dyspepsia. Subsequent upper gastrointestinal endoscopy revealed a friable mass that was located between the distal antrum and the pyloric ring. Biopsy revealed it to be an intestinal type adenocarcinoma. Subtotal gastrectomy was performed after neoadjuvant chemotherapy. Grossly, a large irregular plaque-like tumor lesion was noted at the anterior wall of the distal antrum and pylorus ring near the lesser curvature, measuring 5.6 × 4.8 × 1.0 cm. Histopathological examination of the resected stomach revealed that the plaque-like lesion largely consisted of numerous abnormally large-caliber and tortuous arteries in the submucosa. The increased fibrosis of the submucosa resulted in the formation of elevated plaque. The intestinal type adenocarcinoma was noted to be largely confined to the mucosa layer, with focal submucosal and muscular propria involvement. The patient was discharged one week after the subtotal gastrectomy, and she was alive and well 17 months after discharge, with no major complications. This is the first case of a mass-like Dieulafoy's lesion coexisting with advanced gastric cancer at the distal antrum area. This case highlights the possibility of life-threatening gastric bleeding after mucosal resection or biopsy that could be encountered by endoscopists.

  8. Evaluating the effects of bedding materials and elevated platforms on contact dermatitis and plumage cleanliness of commercial broilers and on litter condition in broiler houses.

    Science.gov (United States)

    Kaukonen, E; Norring, M; Valros, A

    2017-10-01

    1. Experiment 1, comparing wood shavings and ground straw bedding with peat, was performed on 7 broiler farms over two consecutive batches during the winter season. Experiment 2, assessing the effect of elevated (30 cm) platforms, was conducted in three farms replicated with 6 consecutive batches. 2. Footpad lesions were inspected at slaughter following the Welfare Quality® (WQ) assessment and official programme. Hock lesions, plumage cleanliness and litter condition were assessed using the WQ assessment. Litter height, pH, moisture and ammonia were determined. 3. Footpad condition on wood shavings appeared to be worse compared with peat using both methods of assessment and was accompanied by inferior hock skin health. WQ assessment resulted in poorer footpad and hock skin condition on ground straw compared with peat. Farms differed in footpad and hock skin condition. Footpad and hock lesions were not affected by platform treatment. Peat appeared more friable than ground straw. The initial pH of wood shavings was higher and moisture was lower than in peat, but at the end of production period there were no differences. Ground straw exhibited higher initial and lower end pH, and was drier in the beginning than peat. Litter condition and quality were not affected by platform treatment. 4. This study provides new knowledge about the applicability of peat as broiler bedding and shows no negative effects of elevated platforms on litter condition or the occurrence of contact dermatitis in commercial environments. The results suggest a complicated relationship between litter condition, moisture and contact dermatitis. Furthermore, it is concluded that the farmer's ability to manage litter conditions is important, regardless of the chosen litter material. Peat bedding was beneficial for footpad and hock skin health compared with wood shavings and ground straw.

  9. Molecular confirmation of Trichomonas gallinae and other parabasalids from Brazil using the 5.8S and ITS-1 rRNA regions.

    Science.gov (United States)

    Ecco, Roselene; Preis, Ingred S; Vilela, Daniel A R; Luppi, Marcela M; Malta, Marcelo C C; Beckstead, Robert B; Stimmelmayr, Raphaela; Stimmelmayer, Raphaela; Gerhold, Richard W

    2012-11-23

    Clinical, gross, and histopathology lesions and molecular characterization of Trichomonas spp. infection were described in two striped owls (Asio (Rhinoptynx) clamator), one American kestrel (Falco sparverius), two green-winged saltators (Saltator similis), and in a toco toucan (Ramphastos toco) from Brazil. These birds presented clinical signs including emaciation, ruffled feathers, abundant salivation and open mouth breathing presumably due to abundant caseous material. Gross lesions were characterized by multifocal yellow friable plaques on the surface of the tongue, pharynx and/or caseous masses partially occluding the laryngeal entrance. In the owls, the caseous material extended into the mandibular muscles and invaded the sinuses of the skull. Histopathologically, marked necrotic and inflammatory lesions were associated with numerous round to oval, pale eosinophilic structures (6-10μm) with basophilic nuclei, consistent with trichomonads. Organisms similar to those described above also were found in the liver of the two green-winged saltators. To the authors' knowledge, this is the first report of trichomonosis in a striped owl and a toco toucan. Sequence analysis of the Trichomonas spp. internal transcribed spacer 1 (ITS-1) region and partial 5.8S of the ribosomal RNA (rRNA) disclosed significant genetic diversity. Two sequences had 100% identity to Trichomonas gallinae, whereas two sequences had a 99% and 92% identity to a Trichomonas vaginalis-like sequence, respectively. One sequence (green-winged saltator 502-08) had a 100% identity to a newly recognized genus Simplicomonas. Copyright © 2012 Elsevier B.V. All rights reserved.

  10. Uncommon mandibular osteomyelitis in a cat caused by Nocardia africana

    Directory of Open Access Journals (Sweden)

    de Farias Marconi

    2012-12-01

    Full Text Available Abstract Background Nocardiosis is an unusual infection in companion animals characterized by suppurative to pyogranulomatous lesions, localized or disseminated. Cutaneous-subcutaneous, pulmonary and systemic signs are observed in feline nocardiosis. However, osteomyelitis is a rare clinical manifestation in cats. Nocardia cyriacigeorgica (formerly N. asteroides sensu stricto, Nocardia brasiliensis, Nocardia otitidiscaviarum, and Nocardia nova are the most common pathogenic species identified in cats, based on recent molecular classification (16S rRNA gene. The present report is, to our knowledge, the first case of mandibular osteomyelitis in a cat caused by Nocardia africana, diagnosed based upon a combination of methods, including molecular techniques. Case presentation A one-year-old non-neutered female cat, raised in a rural area, was admitted to the Companion Animal Hospital-PUCPR, São José dos Pinhais, State of Paraná, Brazil, with a history a progressive facial lesion, difficulty apprehending food, loss of appetite, apathy and emaciation. Clinical examination showed fever, submandibular lymphadenitis, and a painless, 8 cm diameter mass, which was irregularly-shaped, of firm consistency, and located in the region of the left mandible. The skin around the lesion was friable, with diffuse inflammation (cellulitis, multiple draining sinuses, and exudation of serosanguinous material containing whitish “sulfur” granules. Diagnosis was based initially in clinical signs, microbiological culture, cytological, and histopathological findings, and radiographic images. Molecular sequencing of 16S rRNA of isolate allowed diagnosis of Nocardia africana. Despite supportive care and antimicrobial therapy based on in vitro susceptibility testing the animal died. Conclusion The present report describes a rare clinical case of feline osteomyelitis caused by Nocardia africana, diagnosed based upon a combination of clinical signs, microbiological

  11. Uncommon mandibular osteomyelitis in a cat caused by Nocardia africana.

    Science.gov (United States)

    de Farias, Marconi Rodrigues; Werner, Juliana; Ribeiro, Márcio Garcia; Rodigheri, Sabrina Marin; Cavalcante, Carolina Zaghi; Chi, Kung Darh; Condas, Larissa Anuska Zeni; Gonoi, Tohru; Matsuzama, Tetsuhiro; Yazama, Katsukiyo

    2012-12-06

    Nocardiosis is an unusual infection in companion animals characterized by suppurative to pyogranulomatous lesions, localized or disseminated. Cutaneous-subcutaneous, pulmonary and systemic signs are observed in feline nocardiosis. However, osteomyelitis is a rare clinical manifestation in cats. Nocardia cyriacigeorgica (formerly N. asteroides sensu stricto), Nocardia brasiliensis, Nocardia otitidiscaviarum, and Nocardia nova are the most common pathogenic species identified in cats, based on recent molecular classification (16S rRNA gene). The present report is, to our knowledge, the first case of mandibular osteomyelitis in a cat caused by Nocardia africana, diagnosed based upon a combination of methods, including molecular techniques. A one-year-old non-neutered female cat, raised in a rural area, was admitted to the Companion Animal Hospital-PUCPR, São José dos Pinhais, State of Paraná, Brazil, with a history a progressive facial lesion, difficulty apprehending food, loss of appetite, apathy and emaciation. Clinical examination showed fever, submandibular lymphadenitis, and a painless, 8 cm diameter mass, which was irregularly-shaped, of firm consistency, and located in the region of the left mandible. The skin around the lesion was friable, with diffuse inflammation (cellulitis), multiple draining sinuses, and exudation of serosanguinous material containing whitish "sulfur" granules.Diagnosis was based initially in clinical signs, microbiological culture, cytological, and histopathological findings, and radiographic images. Molecular sequencing of 16S rRNA of isolate allowed diagnosis of Nocardia africana. Despite supportive care and antimicrobial therapy based on in vitro susceptibility testing the animal died. The present report describes a rare clinical case of feline osteomyelitis caused by Nocardia africana, diagnosed based upon a combination of clinical signs, microbiological culture, cytological and histopathological findings, radiographic images, and

  12. 3D-Laser-Scanning Technique Applied to Bulk Density Measurements of Apollo Lunar Samples

    Science.gov (United States)

    Macke, R. J.; Kent, J. J.; Kiefer, W. S.; Britt, D. T.

    2015-01-01

    In order to better interpret gravimetric data from orbiters such as GRAIL and LRO to understand the subsurface composition and structure of the lunar crust, it is import to have a reliable database of the density and porosity of lunar materials. To this end, we have been surveying these physical properties in both lunar meteorites and Apollo lunar samples. To measure porosity, both grain density and bulk density are required. For bulk density, our group has historically utilized sub-mm bead immersion techniques extensively, though several factors have made this technique problematic for our work with Apollo samples. Samples allocated for measurement are often smaller than optimal for the technique, leading to large error bars. Also, for some samples we were required to use pure alumina beads instead of our usual glass beads. The alumina beads were subject to undesirable static effects, producing unreliable results. Other investigators have tested the use of 3d laser scanners on meteorites for measuring bulk volumes. Early work, though promising, was plagued with difficulties including poor response on dark or reflective surfaces, difficulty reproducing sharp edges, and large processing time for producing shape models. Due to progress in technology, however, laser scanners have improved considerably in recent years. We tested this technique on 27 lunar samples in the Apollo collection using a scanner at NASA Johnson Space Center. We found it to be reliable and more precise than beads, with the added benefit that it involves no direct contact with the sample, enabling the study of particularly friable samples for which bead immersion is not possible

  13. In vitro propagation of Pinguicula moranensis H.B.K., var. Neovolcanica Z.

    Directory of Open Access Journals (Sweden)

    Pérez-Sánchez, J.

    2017-01-01

    Full Text Available Seeds of Pinguicula moranensis were collected in the “El Chico” National Park in the state of Hidalgo, Mexico, in order to develop a propagation strategy for in vitro mass multiplication. Seeds were germinated in medium ¼ MS supplemented with 100 mg L-1 inositol, 0.4 mg L-1 thiamine, 20 g L-1 sucrose, 8.5 g L-1 of agar, pH 5.7 (Basal medium with organics, MBO, without growth regulators showing low germination (5 %. Seedlings of 10 days, were incubated in medium MBO with BA (0, 0.5 mg L-1 in combination with NAA (0, 0.5 mg L-1, or 2,4D (0, 1.0 mg L-1. The presence of 2,4-D (1.0 mg L-1, caused necrosis in this species, however MBO medium, supplemented with BA 0.5 mg L-1 and NAA 0.5 mg L-1 , allowed 100 % induction of callus which observed defined and friable. The callus obtained was incubated in the above medium MBO with BA (0, 1 and 2 mg L-1 and NAA (0, 0.1, 0.5 mg L-1. The best response was observed with medium MBO supplemented with BA (1mg L-1 and NAA (0.5 mg L-1, finding an average of 1,957 + 125 shoots per jar. The formed shoots were obtained with a large proportion of vitrification, so they were incubated in the same medium but without growth regulators, where they were devitrified and individualized, rooting spontaneously. Allowing thereby the definition of an efficient protocol for mass propagation of the species.

  14. Feasibility study of heavy oil recovery in the Midcontinent region (Kansas, Missouri, Oklahoma)

    Energy Technology Data Exchange (ETDEWEB)

    Olsen, D.K.; Johnson, W.I.

    1993-08-01

    This report is one of a series of publications assessing the feasibility/constraints of increasing domestic heavy oil production. Each report covers a select area of the United States. The Midcontinent (Kansas, Nssouri, Oklahoma) has produced significant oil, but contrary to early reports, the area does not contain the huge volumes of heavy oil that, along with the development of steam and in situ combustion as oil production technologies, sparked the area`s oil boom of the 1960s. Recovery of this heavy oil has proven economically unfeasible for most operators due to the geology of the formations rather than the technology applied to recover the oil. The geology of the southern Midcontinent, as well as results of field projects using thermal enhanced oil recovery (TEOR) methods to produce the heavy oil, was examined based on analysis of data from secondary sources. Analysis of the performance of these projects showed that the technology recovered additional heavy oil above what was produced from primary production from the consolidated, compartmentalized, fluvial dominated deltaic sandstone formations in the Cherokee and Forest City basins. The only projects producing significant economic and environmentally acceptable heavy oil in the Midcontinent are in higher permeability, unconsolidated or friable, thick sands such as those found in south-central Oklahoma. There are domestic heavy oil reservoirs in other sedimentary basins that are in younger formations, are less consolidated, have higher permeability and can be economically produced with current TEOR technology. Heavy oil production from the carbonates of central and wester Kansas has not been adequately tested, but oil production is anticipated to remain low. Significant expansion of Midcontinent heavy oil production is not anticipated because the economics of oil production and processing are not favorable.

  15. Risk factors for recurrent spontaneous epistaxis.

    Science.gov (United States)

    Abrich, Victor; Brozek, Annabelle; Boyle, Timothy R; Chyou, Po-Huang; Yale, Steven H

    2014-12-01

    To identify risk factors associated with spontaneous recurrent epistaxis. This was a retrospective cohort study assessing patients in the Marshfield Clinic system diagnosed as having epistaxis between January 1, 1991, and January 1, 2011. There were 461 cases with at least 2 episodes of spontaneous epistaxis within 3 years and 912 controls with only 1 episode in the same time frame. More than 50 potential risk factors were investigated, including demographic features, substance use, nasal anatomical abnormalities, nasal infectious and inflammatory processes, medical comorbidities, medications, and laboratory values. A Cox proportional hazards regression modeling approach was used to calculate hazard ratios of epistaxis recurrence. Traditional risk factors for epistaxis, including nasal perforation, nasal septum deviation, rhinitis, sinusitis, and upper respiratory tract infection, did not increase the risk of recurrence. Significant risk factors for recurrent epistaxis included congestive heart failure, diabetes mellitus, hypertension, and a history of anemia. Warfarin use increased the risk of recurrence, independent of international normalized ratio. Aspirin and clopidogrel were not found to increase the risk of recurrence. Few major adverse cardiovascular events were observed within 30 days of the first epistaxis event. Congestive heart failure is an underappreciated risk factor for recurrent epistaxis. Hypertension and diabetes mellitus may induce atherosclerotic changes in the nasal vessels, making them friable and more at risk for bleeding. Patients with recurrent epistaxis may also be more susceptible to developing anemia. Physicians should promote antiplatelet and antithrombotic medication adherence despite an increased propensity for recurrent epistaxis to prevent major adverse cardiovascular events. Copyright © 2014 Mayo Foundation for Medical Education and Research. Published by Elsevier Inc. All rights reserved.

  16. Optimization of callus induction of Zataria multiflora under the effect of different plant growth regulators and explant source

    Directory of Open Access Journals (Sweden)

    N. Mosavat*

    2017-11-01

    Full Text Available Background and objectives: The Lamiaceae family is rich in favorable secondary metabolites which have different medicinal properties and also use in food, cosmetic and sanitary industry. Zataria multiflora Boiss. is an aromatic and bushy plant containing specific pharmaceutical components which is only distributed in certain regions of Iran. Tissue culture technologies could be suitable for in vitro production of Zataria. Methods: In this study, callus production and callus related traits of Zataria was evaluated at in vitro condition. Callus induction was performed on Murashige and Skoog (MS medium containing different levels of plant growth regulators including different cytokinins (Kinetin, benzyl amino purine and auxins (2,4 dichlorophenoxyacetic acid and naphtalen acetic acid and two different explant (hypocotyl and leaf. Results: The friable calli with yellow-green color only appeared from leaf explants on three different treatments including: 1: 2.5 (mg/L 2,4-D; 2: 2 (mg/L  2,4-D; 3: [2 (mg/L 2,4-D+ 1 (mg/L Kin].  The best callus induction (75% was obtained at 2,4-D (2 mg/L + Kin (1 mg/L after 2 month of incubation under the photoperiod of 16/8 (light/dark. The highest callus growth rate (CGR (0.072 mm/day and callus fresh weight (0.135 g were denoted to the treatment of 2 mg/L (2,4-D.  Conclusion: The benefits of the protocol described here include the possibility of its use throughout the callus culture for commercial production of suitable secondary metabolites of Zataria in rapid time and huge scale.

  17. Histoplasma capsulatum Endocarditis

    Science.gov (United States)

    Riddell, James; Kauffman, Carol A.; Smith, Jeannina A.; Assi, Maha; Blue, Sky; Buitrago, Martha I.; Deresinski, Stan; Wright, Patty W.; Drevets, Douglas A.; Norris, Steven A.; Vikram, Holenarasipur R.; Carson, Paul J.; Vergidis, Paschalis; Carpenter, John; Seidenfeld, Steven M.; Wheat, L. Joseph

    2014-01-01

    Abstract Infective endocarditis is an uncommon manifestation of infection with Histoplasma capsulatum. The diagnosis is frequently missed, and outcomes historically have been poor. We present 14 cases of Histoplasma endocarditis seen in the last decade at medical centers throughout the United States. All patients were men, and 10 of the 14 had an infected prosthetic aortic valve. One patient had an infected left atrial myxoma. Symptoms were present a median of 7 weeks before the diagnosis was established. Blood cultures yielded H. capsulatum in only 6 (43%) patients. Histoplasma antigen was present in urine and/or serum in all but 3 of the patients and provided the first clue to the diagnosis of histoplasmosis for several patients. Antibody testing was positive for H. capsulatum in 6 of 8 patients in whom the test was performed. Eleven patients underwent surgery for valve replacement or myxoma removal. Large, friable vegetations were noted at surgery in most patients, confirming the preoperative transesophageal echocardiography findings. Histopathologic examination of valve tissue and the myxoma revealed granulomatous inflammation and large numbers of organisms in most specimens. Four of the excised valves and the atrial myxoma showed a mixture of both yeast and hyphal forms on histopathology. A lipid formulation of amphotericin B, administered for a median of 29 days, was the initial therapy in 11 of the 14 patients. This was followed by oral itraconazole therapy, in all but 2 patients. The length of itraconazole suppressive therapy ranged from 11 months to lifelong administration. Three patients (21%) died within 3 months of the date of diagnosis. All 3 deaths were in patients who had received either no or minimal (1 day and 1 week) amphotericin B. PMID:25181311

  18. Diagnosis of invasive aspergillus tracheobronchitis facilitated by endobronchial ultrasound-guided transbronchial needle aspiration: a case report

    Directory of Open Access Journals (Sweden)

    Casal Roberto F

    2009-11-01

    Full Text Available Abstract Introduction Invasive pulmonary aspergillosis is the most common form of infection by Aspergillus species among immunocompromised patients. Although this infection frequently involves the lung parenchyma, it is unusual to find it limited to the tracheobronchial tree, a condition known as invasive aspergillus tracheobronchitis. Case presentation A 65 year-old Hispanic man from Bolivia with a history of chronic lymphocytic leukemia developed cough and malaise eight months after having an allogenic stem cell transplant. A computed tomography of the chest revealed an area of diffuse soft tissue thickening around the left main stem bronchus, which was intensely fluorodeoxyglucose-avid on positron emission tomography scanning. An initial bronchoscopic exam revealed circumferential narrowing of the entire left main stem bronchus with necrotic and friable material on the medial wall. Neither aspirates from this necrotic area nor bronchial washing were diagnostic. A second bronchoscopy with endobronchial ultrasound evidenced a soft tissue thickening on the medial aspect of the left main stem bronchus underlying the area of necrosis visible endoluminally. Endobronchial ultrasound-guided transbronchial needle aspiration performed in this area revealed multiple fungal elements suggestive of Aspergillus species. Conclusion We describe the first case of invasive aspergillus tracheobronchitis in which the diagnosis was facilitated by the use of endobronchial ultrasound guided trans-bronchial needle aspiration. To the best of our knowledge, we are also presenting the first positron emission tomography scan images of this condition in the literature. We cautiously suggest that endobronchial ultrasound imaging may be a useful tool to evaluate the degree of invasion and the involvement of vascular structures in these patients prior to bronchoscopic manipulation of the affected areas in an effort to avoid potentially fatal hemorrhage.

  19. Indução de calos embriogênicos em explantes de cupuaçuzeiro Induction of embryogenics calli in cupuassu explants

    Directory of Open Access Journals (Sweden)

    Maria das Graças Rodrigues Ferreira

    2004-08-01

    Full Text Available Objetivou-se a indução de calos embriogênicos em cupuaçuzeiro, em função do tipo de explante e meio de cultura. Foram testados como explantes, segmentos cotiledonares e eixos embrionários divididos em três partes: região da plúmula, radícula e hipocótilo. Os explantes foram cultivados em 2 diferentes meios de cultura: 1 MS suplementado com 2,4-D (1 mg L-1 e Cinetina (0,25 mg L-1; 2 MS acrescido de ANA (5 mg L-1 e Cinetina (0,25 mg L-1. Constatou-se que a região do hipocótilo foi a parte mais responsiva do eixo embrionário, formando calos com aspecto branco e friável. As auxinas testadas nos meios não estimularam o processo embriogênico em calos de cupuaçuzeiro.It was studied the induction of embryogenics calli in cupuassu, in function of kind of explant and culture medium. Cotyledons segments and embryonic axes were tested and divided in three parts: region of plumule, radicule and hypocotile. The explants were cultivated in two different culture medium: 1 MS supplemented with 2,4-D (1 mg L-1 and Kinetin (0,25 mg L-1; 2 MS supplemented with NAA (5 mg L-1 and Kinetin (0,25 mg L-1. The hypocotile region demonstrated to be more responsive segment of the embryonic axe, forming callus with white and friable aspect. No somatic embryogenesis was evidenced in callus of cupuassu with auxines testeds in the medium.

  20. Assessing asbestos exposure potential in nonindustrial settings.

    Science.gov (United States)

    Chang, S N; White, L E; Scott, W D

    1987-01-01

    The presence of asbestos containing materials (ACM) in office and commercial buildings is a significant environmental problem. Asbestosis, mesothelioma and lung cancer have been linked with industrial exposure to airborne asbestos. The extensive use of asbestos products in buildings has raised concerns about the widespread exposure of the general public to asbestos in nonoccupational settings. The presence of asbestos in a building does not necessarily mean that significant exposure of the occupants of the building has occurred, but it is important that the asbestos be monitored regularly to ensure that fibers do not become airborne. If ACM are contained within a matrix and not disturbed, exposure is unlikely. However, if the asbestos becomes friable (crumbling) or if building maintenance, repair, renovation or other activities disturb ACM, airborne asbestos fibers may be a source of exposure to the occupants of the building. Currently, asbestos exposure assessment is conducted by a phase contrast light microscope (PCM) technique. Due to its inherent limitation in resolution and the generic counting rules used, analysis by the PCM method underestimates the airborne asbestos fiber concentration as compared to analysis by transmission electron microscopy (TEM). It is important that the air monitoring results analyzed by PCM be interpreted carefully in conjunction with a survey by a professional to judge the physical condition of the ACM in buildings. Exposure levels to airborne asbestos fibers vary from day to day and depend on the physical condition of the material involved and the type of operating and maintenance program in place.(ABSTRACT TRUNCATED AT 250 WORDS)

  1. Influence of fuelwood trees on sodic soils

    International Nuclear Information System (INIS)

    Garg, V.K.; Jain, R.K.

    1992-01-01

    The persistent acute fuelwood shortage problem in India has necessitated having tree plantations on waste lands to obtain renewable energy. Fuelwood production screening trials initiated in 1981 at the Biomass Research Centre in Banthra, India identified babul, Acacia nilotica (L.) Wild. ex Delile, and mesquite, Prosopis juliflora (Swartz) DC., to be the most promising and suitable leguminous trees in terms of biomass production on sodic sites. A study was carried out to assess soil enrichment due to the growth of these fuelwood trees planted a decade past on sordic soil that had had no other amendments. Results showed preferential nutrient accumulation and greater reduction in soil pH (from 9.5 to 7.9) and exchangeable sodium (from 30 to 8%) at the P. juliflora plantation compared with at the A. nilotica plantation. There was also a reduction in surface soil (0-15 cm) bulk density, but an enhancement in porosity and water holding capacity, making soil more friable. The P. juliflora plantation produced markedly more leaf litter than the A. nilotica plantation. Both the species had fibrous lateral root systems on the surface in the sodic soil. However, the penetration and spread of roots were almost 2-fold greater in P. juliflora than in A. nilotica. Thus, the potential magnitude of changes in soil properties was related to the distribution of roots and amount of litter falling on the soil surface. Prosopis juliflora appeared to be better than A. nilotica under adverse sodic soil conditions in establishing an enlarged plant-litter nutrient cycle relationship. This study also provides an assessment of soil amelioration by leguminous trees under short-rotation forestry practices. 16 refs., 7 figs., 4 tabs

  2. Influence of fuelwood trees on sodic soils

    Energy Technology Data Exchange (ETDEWEB)

    Garg, V.K.; Jain, R.K. (National Botanical Research Inst., Lucknow (India))

    1992-01-01

    The persistent acute fuelwood shortage problem in India has necessitated having tree plantations on waste lands to obtain renewable energy. Fuelwood production screening trials initiated in 1981 at the Biomass Research Centre in Banthra, India identified babul, Acacia nilotica (L.) Wild. ex Delile, and mesquite, Prosopis juliflora (Swartz) DC., to be the most promising and suitable leguminous trees in terms of biomass production on sodic sites. A study was carried out to assess soil enrichment due to the growth of these fuelwood trees planted a decade past on sordic soil that had had no other amendments. Results showed preferential nutrient accumulation and greater reduction in soil pH (from 9.5 to 7.9) and exchangeable sodium (from 30 to 8%) at the P. juliflora plantation compared with at the A. nilotica plantation. There was also a reduction in surface soil (0-15 cm) bulk density, but an enhancement in porosity and water holding capacity, making soil more friable. The P. juliflora plantation produced markedly more leaf litter than the A. nilotica plantation. Both the species had fibrous lateral root systems on the surface in the sodic soil. However, the penetration and spread of roots were almost 2-fold greater in P. juliflora than in A. nilotica. Thus, the potential magnitude of changes in soil properties was related to the distribution of roots and amount of litter falling on the soil surface. Prosopis juliflora appeared to be better than A. nilotica under adverse sodic soil conditions in establishing an enlarged plant-litter nutrient cycle relationship. This study also provides an assessment of soil amelioration by leguminous trees under short-rotation forestry practices. 16 refs., 7 figs., 4 tabs.

  3. Pathology of experimental Machupo virus infection, Chicava strain, in cynomolgus macaques (Macaca fascicularis) by intramuscular and aerosol exposure.

    Science.gov (United States)

    Bell, T M; Shaia, C I; Bunton, T E; Robinson, C G; Wilkinson, E R; Hensley, L E; Cashman, K A

    2015-01-01

    Machupo virus, the causative agent of Bolivian hemorrhagic fever (BHF), is a highly lethal viral hemorrhagic fever of which little is known and for which no Food and Drug Administration-approved vaccines or therapeutics are available. This study evaluated the cynomolgus macaque as an animal model using the Machupo virus, Chicava strain, via intramuscular and aerosol challenge. The incubation period was 6 to 10 days with initial signs of depression, anorexia, diarrhea, mild fever, and a petechial skin rash. These were often followed by neurologic signs and death within an average of 18 days. Complete blood counts revealed leukopenia as well as marked thrombocytopenia. Serum chemistry values identified a decrease in total protein, marked increases in alanine aminotransferase and aspartate aminotransferase, and moderate increases in alkaline phosphatase. Gross pathology findings included a macular rash extending across the axillary and inguinal regions beginning at approximately 10 days postexposure as well as enlarged lymph nodes and spleen, enlarged and friable liver, and sporadic hemorrhages along the gastrointestinal mucosa and serosa. Histologic lesions consisted of foci of degeneration and necrosis/apoptosis in the haired skin, liver, pancreas, adrenal glands, lymph nodes, tongue, esophagus, salivary glands, stomach, small intestine, and large intestine. Lymphohistiocytic interstitial pneumonia was also present. Inflammation within the central nervous system (nonsuppurative encephalitis) was histologically apparent approximately 16 days postexposure and was generally progressive. This study provides insight into the course of Machupo virus infection in cynomolgus macaques and supports the usefulness of cynomolgus macaques as a viable model of human Machupo virus infection. © The Author(s) 2014.

  4. Colite por citomegalovirus em paciente transplantada renal: relato de caso e revisão da literatura Citomegalovirus colitis in kidney transplant patient: case report and literature review

    Directory of Open Access Journals (Sweden)

    Rogério Saad Hossne

    2007-06-01

    Full Text Available A infecção do citomegalovírus ocorre geralmente em pacientes imunocomprometidos sejam pós-transplantados ou pelas doenças que comprometem o sistema imune (AIDS; apresentamos um caso de um paciente do sexo feminino de 49 anos de idade, que se encontrava em pós-operatório tardio de transplante renal (14 anos, fazendo uso de medicações imunossupressoras. Evolui com quadro de dor abdominal, perda do peso e diarréia não sanguinolenta na fase inicial, necessitando de hospitalização, durante a qual desenvolveu severos quadros de hematoquezia e hipotensão. Submetida a colonoscopia que revelou mucosa de aspecto friável, com úlceras do tipo aftóides, fibrina e formação de pseudopólipos; a biopsia revelou tratar-se de citomegalovírus. Evolui sem melhora com o uso do foscarnet r, necessitando de tratamento cirúrgico, indo a óbito após 5 dias.Cytomegalovirus infection frequently develops in immunocompromised patients, either in post-transplanted patients or in patients with diseases that affects the immune system, such as AIDS; we present a case of a 49 year old female patient in late post surgery (14 years of a kidney transplant, using immunosuppressing medication. The patient presented abdominal pain, weight loss and initial diarrhea, she was hospitalized and developed severe hematochezia and hypotension. The patient was submitted to a colonoscopy and presented friable aspect mucosa, with aphthoid ulcers, fibrin and pseudopolyp formation; biopsy revealed cytomegalovirus. Her condition did not improve after the use of foscarnet, and surgical treatment was necessary. The patient died 5 days later.

  5. Foam, composition and method of production

    Energy Technology Data Exchange (ETDEWEB)

    Ghali, R.

    1991-09-03

    A ternary foam is disclosed which overcomes the disadvantages of conventional heat-insulating foams which are either dense and heavy, expensive to produce, friable, unstable, or have poor fire resistance. The foam of the invention has, by weight of the reaction product, 10-35% polyurethane, 30-55% polyisocyanurate, and 20-45% polyurea. The foam is a reaction product of 100 parts by weight of an organic polyisocyanate with: 15-25 parts by weight of a polyether polyol having a hydroxyl number of ca 28-35 and a molecular weight of not more than 6,000; 5-25 parts by weight of water; 0-25 parts by weight of a blowing agent; 0-50 parts by weight of a filler-plasticizer fire retardant; an effective amount of a low activation catalyst to initiate water-isocyanate reaction to produce polyurea and polyol-isocyanate reaction to produce polyurethane; and an effective amount of a high activation catalyst to retard the low activation catalyst and promote the formation of polyisocyanurate. The low activity catalyst is present in an amount ranging ca 1.5-9 parts per 100 parts by weight of the polyisocyanate, and the high activation catalyst is present in an amount ranging 0.0008-0.002 parts per 100 parts by weight of the polyisocyanate. Water as a reactant and blowing agent can be substituted by an effective amount of a disubstituted amine such as diethanol amine and an inert blowing agent such as fluorocarbon. The resultant foam has excellent heat insulating propeties, is semi-flexible, has a density of 0.5-0.9 lb/ft{sup 3}, and can be inexpensively produced by existing 2-component foam dispensing equipment. 1 fig., 1 tab.

  6. Effect of processing parameters on the formation of C{sub f}/LAS composites/Ag−Cu−Ti/TC4 brazed joint

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Duo; Niu, Hongwei [Shandong Provincial Key Laboratory of Special Welding Technology, Harbin Institute of Technology at Weihai, Weihai 264209 (China); Liu, Jihou [State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Song, Xiaoguo, E-mail: songxg@hitwh.edu.cn [Shandong Provincial Key Laboratory of Special Welding Technology, Harbin Institute of Technology at Weihai, Weihai 264209 (China); State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Xia, Long [School of Materials Science and Engineering, Harbin Institute of Technology at Weihai, Weihai 264209 (China); Feng, Jicai [Shandong Provincial Key Laboratory of Special Welding Technology, Harbin Institute of Technology at Weihai, Weihai 264209 (China); State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China)

    2016-10-15

    C{sub f}/LAS composites were successfully jointed to TC4 alloy with Ag−Cu−Ti filler by vacuum brazing. The interfacial microstructure of TC4/C{sub f}/LAS composites joints was characterized by employing scanning electron microscope (SEM), energy dispersive spectrometer (EDS), X-diffraction (XRD) and transmission electron microscopy (TEM). The determination of the thin interfacial reaction layer (TiSi{sub 2} + TiC layer) was realized by TEM. The effect of holding time on the interfacial microstructure and shear strength were investigated. With the increasing holding time, the thickness of diffusion layer, Ti{sub 3}Cu{sub 4} layer, and TiSi{sub 2} + TiC layer increased obviously, on the contrary, that of Ti−Cu intermetallic compound layers decreased gradually. Besides, blocky Ti{sub 3}Cu{sub 4} phase was coarsened when the joint was brazed at 890 °C for 20 min, which deteriorated the mechanical properties of the joint dramatically. The interfacial evolution of TC4/C{sub f}/LAS composites joint and the formation of TiSi{sub 2}, TiC, Ti{sub 3}Cu{sub 4}, TiCu and Ti{sub 2}Cu phases were expounded. The maximum shear strength of 26.4 MPa was obtained when brazed at 890 °C for 10 min. - Highlights: •The thin interface reaction layer was determined to be TiSi{sub 2} + TiC layer by TEM. •Holding time had influence on the interfacial microstructure and joint properties. •Microstructural evolution mechanism and reactions of brazed joints were expounded.

  7. Microstructural stability and mechanical properties of a boron modified Ni–Fe based superalloy for steam boiler applications

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Changshuai, E-mail: cswang@imr.ac.cn; Guo, YongAn; Guo, Jianting; Zhou, Lanzhang, E-mail: lzz@imr.ac.cn

    2015-07-15

    Ni–Fe based superalloys are being considered as boiler materials in 700 °C advanced ultra-supercritical (A-USC) coal fired power plants due to their excellent oxidation and hot corrosion resistance, outstanding workability and low cost. In this paper, the microstructural stability and mechanical properties of a boron (B) modified Ni–Fe based superalloy designed for 700 °C A-USC during thermal exposure at 650–750 °C for up to 5000 h were investigated. The results show that adding boron has no apparent influence on the major precipitates, including spherical γ′ and blocky MC. However, the amount of M{sub 23}C{sub 6} decreases markedly after standard heat treatment. During long-term thermal exposure, the addition of boron has no influence on γ′ coarsening, η phase precipitation and primary MC degeneration, but decreases the growth rate of M{sub 23}C{sub 6} along grain boundary. The stress rupture life and ductility are obviously improved after the addition of B. Meanwhile, the yield strength of B-doped alloy almost keeps the same level as that without boron addition. The fracture surface characterization exhibits that the dimples increase significantly after adding boron. During long-term thermal exposure, the elongation of the alloy with B addition increases slightly, but, for the alloy without B addition, the elongation obviously increases. The improvement of the stress rupture life and ductility can be attributed to the increase of grain boundary strength and the optimization of M{sub 23}C{sub 6} carbide distribution at grain boundary.

  8. Effects of La2O3 on microstructure and wear properties of laser clad γ/Cr7C3/TiC composite coatings on TiAl intermatallic alloy

    International Nuclear Information System (INIS)

    Liu Xiubo; Yu Rongli

    2007-01-01

    The effects of La 2 O 3 addition on the microstructure and wear properties of laser clad γ/Cr 7 C 3 /TiC composite coatings on γ-TiAl intermetallic alloy substrates with NiCr-Cr 3 C 2 precursor mixed powders have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and energy-dispersive spectrometer (EDS) and block-on-ring wear tests. The responding wear mechanisms are discussed in detail. The results are compared with that for composite coating without La 2 O 3 . The comparison indicates that no evident new crystallographic phases are formed except a rapidly solidified microstructure consisting of the primary hard Cr 7 C 3 and TiC carbides and the γ/Cr 7 C 3 eutectics distributed in the tough γ nickel solid solution matrix. Good finishing coatings can be achieved under a proper amount of La 2 O 3 -addition and a suitable laser processing parameters. The additions of rare-earth oxide La 2 O 3 can refine and purify the microstructure of coatings, relatively decrease the volume fraction of primary blocky Cr 7 C 3 to Cr 7 C 3 /γ eutectics, reduce the dilution of clad material from base alloy and increase the microhardness of the coatings. When the addition of La 2 O 3 is approximately 4 wt.%, the laser clad composite coating possesses the highest hardness and toughness. The composite coating with 4 wt.%La 2 O 3 addition can result the best enhancement of wear resistance of about 30%. However, too less or excessive addition amount of La 2 O 3 have no better influence on wear resistance of the composite coating

  9. High and highly variable cooling rates during pyroclastic eruptions on Axial Seamount, Juan de Fuca Ridge

    Science.gov (United States)

    Helo, Christoph; Clague, David A.; Dingwell, Donald B.; Stix, John

    2013-03-01

    We present a calorimetric analysis of pyroclastic glasses and glassy sheet lava flow crusts collected on Axial Seamount, Juan de Fuca Ridge, NE Pacific Ocean, at a water depth of about 1400 m. The pyroclastic glasses, subdivided into thin limu o Pele fragments and angular, blocky clasts, were retrieved from various stratigraphic horizons of volcaniclastic deposits on the upper flanks of the volcanic edifice. Each analysed pyroclastic sample consists of a single type of fragment from one individual horizon. The heat capacity (cp) was measured via differential scanning calorimetry (DSC) and analysed using relaxation geospeedometry to obtain the natural cooling rate across the glass transition. The limu o Pele samples (1 mm grain size fraction) and angular fragments (0.5 mm grain size fraction) exhibit cooling rates of 104.3 to 106.0 K s- 1 and 103.9 to 105.1 K s- 1, respectively. A coarser grain size fraction, 2 mm for limu o Pele and 1 mm for the angular clasts yields cooling rates at the order of 103.7 K s- 1. The range of cooling rates determined for the different pyroclastic deposits presumably relates to the size or intensity of the individual eruptions. The outer glassy crusts of the sheet lava flows were naturally quenched at rates between 63 K s- 1 and 103 K s- 1. By comparing our results with published data on the very slow quenching of lava flow crusts, we suggest that (1) fragmentation and cooling appear to be coupled dynamically and (2) ductile deformation upon the onset of cooling is restricted due to the rapid increase in viscosity. Lastly, we suggest that thermally buoyant plumes that may arise from rapid heat transfer efficiently separate clasts based on their capability to rise within the plume and as they subsequently settle from it.

  10. Impact Toughness of Subzones in the Intercritical Heat-Affected Zone of Low-Carbon Bainitic Steel

    Directory of Open Access Journals (Sweden)

    Zhenshun Li

    2018-06-01

    Full Text Available The subzones of the intercritical heat-affected zone (IC HAZ of low-carbon bainitic steel were simulated by using a Gleeble-3500 simulator to study the impact toughness. The results showed that the IC HAZ is not entirely brittle and can be further divided into three subzones according to the impact toughness or peak welding temperature; the invariant subzone heated between the critical transformation start temperature (Ac1 and 770 °C exhibited unchanged high impact toughness. Furthermore, an extremely low impact toughness was found in the embrittlement subzone, heated between 770 and 830 °C, and the reduction subzone heated between 830 °C and the critical transformation finish temperature (Ac3 exhibited toughness below that of the original metal. The size of the blocky martensite-austenite (M-A constituents was found to have a remarkable level of influence on the impact toughness when heated below 830 °C. Additionally, it was found that, once the constituent size exceeds a critical value of 3.0 µm at a peak temperature of 770 °C, the IC HAZ becomes brittle regardless of lath or twinned martensite constitution in the M-A constituent. Essentially, embrittlement was observed to occur when the resolved length of initial cracks (in the direction of the overall fracture formed as a result of the debonding of M-A constituents exceeding the critical Griffith size. Furthermore, when the heating temperature exceeded 830 °C, the M-A constituents formed a slender shape, and the impact toughness increased as the area fraction of the slender M-A constituents decreased.

  11. Impact Toughness of Subzones in the Intercritical Heat-Affected Zone of Low-Carbon Bainitic Steel.

    Science.gov (United States)

    Li, Zhenshun; Zhao, Xuemin; Shan, Dongri

    2018-06-06

    The subzones of the intercritical heat-affected zone (IC HAZ) of low-carbon bainitic steel were simulated by using a Gleeble-3500 simulator to study the impact toughness. The results showed that the IC HAZ is not entirely brittle and can be further divided into three subzones according to the impact toughness or peak welding temperature; the invariant subzone heated between the critical transformation start temperature ( A c1 ) and 770 °C exhibited unchanged high impact toughness. Furthermore, an extremely low impact toughness was found in the embrittlement subzone, heated between 770 and 830 °C, and the reduction subzone heated between 830 °C and the critical transformation finish temperature ( A c3 ) exhibited toughness below that of the original metal. The size of the blocky martensite-austenite (M-A) constituents was found to have a remarkable level of influence on the impact toughness when heated below 830 °C. Additionally, it was found that, once the constituent size exceeds a critical value of 3.0 µm at a peak temperature of 770 °C, the IC HAZ becomes brittle regardless of lath or twinned martensite constitution in the M-A constituent. Essentially, embrittlement was observed to occur when the resolved length of initial cracks (in the direction of the overall fracture) formed as a result of the debonding of M-A constituents exceeding the critical Griffith size. Furthermore, when the heating temperature exceeded 830 °C, the M-A constituents formed a slender shape, and the impact toughness increased as the area fraction of the slender M-A constituents decreased.

  12. Caracterización geoquímica de la esméctica en varias formaciones arcillosas de los flyschs del Campo de Gibraltar (Cádiz, España

    Directory of Open Access Journals (Sweden)

    Esteras Martín, M.

    1993-12-01

    Full Text Available The «Jimena clays», «basal series of Aljibe» and «blocky clays» formations are compared from the mineralogical and geochemical analysis. The mineralogy of clays is very similar in all the sequences analyzed and consists of quartz, smectite, illite and kaolinite. Smaller amounts of feldspar, gypsum and chlorite are locally presento In the 2-20 μm and Se comparan desde un punto de vista mineralógico y geoquímico las formaciones definidas como «arcillas de Jimena», «sucesión basal del Aljibe» y «arcillas con bloques». Su mineralogía resulta muy similar: cuarzo, esmectita, ilita y caolinita, junto con pequeñas proporciones de feldespato, yeso y clorita. En las fracciones 2-20 µm y < 2 μm la esmectita es el mineral más abundante. La semejanza mineralógica se pone también de manifiesto en la composición química de estos materiales. La composición de las esmectitas corresponde a montmorillonita y sugiere un origen detrítico para las mismas. El contenido en diversos elementos traza indica que estos materiales son el producto de la meteorización de rocas magmáticas ácidas junto con rocas sedimentarias antiguas. La homogeneidad de las secuencias analizadas indica, asimismo, una homología de todas las formaciones y una gran uniformidad en los aportes durante el intervalo Cretácico-Eoceno, época a la que se atribuye su depósito.

  13. Microstructural and mechanical characterization of Al–Zn–Si nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    García-Villarreal, S. [Centro de Investigación en Materiales Avanzados S.C. Monterrey, 66600, Alianza Nte. 202, Parque PIIT, Apodaca, N.L. (Mexico); Chávez-Valdez, A. [Katcon Institute for Innovation and Technology KIIT, 66629, Alianza Sur 200, Apodaca, N.L. (Mexico); Moreno, K.J. [Instituto Tecnológico de Celaya, Apartado Postal 57, 38010 Celaya, Guanajuato (Mexico); Leyva, C.; Aguilar-Martínez, J.A. [Centro de Investigación en Materiales Avanzados S.C. Monterrey, 66600, Alianza Nte. 202, Parque PIIT, Apodaca, N.L. (Mexico); Hurtado, A. [Centro de Investigación en Materiales Avanzados S.C., 31109, Miguel de Cervantes 120, Chih., Chih. (Mexico); Arizmendi-Morquecho, A., E-mail: ana.arizmendi@cimav.edu.mx [Centro de Investigación en Materiales Avanzados S.C. Monterrey, 66600, Alianza Nte. 202, Parque PIIT, Apodaca, N.L. (Mexico)

    2013-09-15

    In this paper the addition of silicon nanoparticles into Al–Zn alloys to form metallic matrix nanocomposites by mechanical alloying process was investigated. The influence of various process parameters such as milling time and Si concentration in the Al–Zn matrix has an interesting effect on the microstructure and mechanical properties of the synthesized nanocomposites. The microstructural characterization of the nanocomposites was evaluated by transmission electron microscopy and energy dispersive X-ray spectroscopy (TEM–EDXS) and the mechanical properties were measured by nanoindentation and micro-hardness tests. The results showed that during mechanical milling Si is added to the Al–Zn matrix achieving a uniform and homogeneous dispersion. After solidification, it forms small particles of AlZnSi with blocky morphology in interdendritic regions. The nanoindentation profiles showed that the elastic modulus and hardness properties increase with increasing milling time. However, a high concentration of Si (> 1.2 wt.%) results in a saturation of Si in the Al–Zn matrix, which adversely affects the mechanical properties. Thus, it is important to tune the milling time and concentration of Si added to the Al–Zn alloys to control the growth of brittle phases that result in reduction of the mechanical properties of the material. - Highlights: • A novel technique for addition of Si nanocomposites into Al–Zn liquid alloy is reported. • Good dispersion and homogeneity of Si in the Al–Zn matrix are obtained. • Increasing Si content above 1.2 wt.% decreases the mechanical properties of Al–Zn alloy. • The saturation point of Si in 1.2 wt.% differs from Galvalume® composition. • The Al–Zn–1.5Si alloy with addition of nanocomposite shows 5.7 GPa of hardness.

  14. Microstructural stability and mechanical properties of a boron modified Ni–Fe based superalloy for steam boiler applications

    International Nuclear Information System (INIS)

    Wang, Changshuai; Guo, YongAn; Guo, Jianting; Zhou, Lanzhang

    2015-01-01

    Ni–Fe based superalloys are being considered as boiler materials in 700 °C advanced ultra-supercritical (A-USC) coal fired power plants due to their excellent oxidation and hot corrosion resistance, outstanding workability and low cost. In this paper, the microstructural stability and mechanical properties of a boron (B) modified Ni–Fe based superalloy designed for 700 °C A-USC during thermal exposure at 650–750 °C for up to 5000 h were investigated. The results show that adding boron has no apparent influence on the major precipitates, including spherical γ′ and blocky MC. However, the amount of M 23 C 6 decreases markedly after standard heat treatment. During long-term thermal exposure, the addition of boron has no influence on γ′ coarsening, η phase precipitation and primary MC degeneration, but decreases the growth rate of M 23 C 6 along grain boundary. The stress rupture life and ductility are obviously improved after the addition of B. Meanwhile, the yield strength of B-doped alloy almost keeps the same level as that without boron addition. The fracture surface characterization exhibits that the dimples increase significantly after adding boron. During long-term thermal exposure, the elongation of the alloy with B addition increases slightly, but, for the alloy without B addition, the elongation obviously increases. The improvement of the stress rupture life and ductility can be attributed to the increase of grain boundary strength and the optimization of M 23 C 6 carbide distribution at grain boundary

  15. A decade of volcanic construction and destruction at the summit of NW Rota-1 seamount: 2004-2014

    Science.gov (United States)

    Schnur, Susan R.; Chadwick, William W.; Embley, Robert W.; Ferrini, Vicki L.; de Ronde, Cornel E. J.; Cashman, Katharine V.; Deardorff, Nicholas D.; Merle, Susan G.; Dziak, Robert P.; Haxel, Joe H.; Matsumoto, Haru

    2017-03-01

    Arc volcanoes are important to our understanding of submarine volcanism because at some sites frequent eruptions cause them to grow and collapse on human timescales. This makes it possible to document volcanic processes. Active submarine eruptions have been observed at the summit of NW Rota-1 in the Mariana Arc. We use remotely operated vehicle videography and repeat high-resolution bathymetric surveys to construct geologic maps of the summit of NW Rota-1 in 2009 and 2010 and relate them to the geologic evolution of the summit area over a 10 year period (2004-2014). We find that 2009 and 2010 were characterized by different eruptive styles, which affected the type and distribution of eruptive deposits at the summit. Year 2009 was characterized by ultraslow extrusion and autobrecciation of lava at a single eruptive vent, producing a large cone of blocky lava debris. In 2010, higher-energy explosive eruptions occurred at multiple closely spaced vents, producing a thin blanket of pebble-sized tephra overlying lava flow outcrops. A landslide that occurred between 2009 and 2010 had a major effect on lithofacies distribution by removing the debris cone and other unconsolidated deposits, revealing steep massive flow cliffs. This relatively rapid alternation between construction and destruction forms one end of a seamount growth and mass wasting spectrum. Intraplate seamounts, which tend to grow larger than arc volcanoes, experience collapse events that are orders of magnitude larger and much less frequent than those occurring at subduction zone settings. Our results highlight the interrelated cyclicity of eruptive activity and mass wasting at submarine arc volcanoes.

  16. Estimation of lattice strain for zirconia nanoparticles based on Williamson- Hall analysis

    Energy Technology Data Exchange (ETDEWEB)

    Aly, Kamal A., E-mail: kamalaly2001@gmail.com [Physics Department, Faculty of Science & Arts, Khullais, University of Jeddah, Jeddah (Saudi Arabia); Physics Department, Faculty of Science, Al-Azhar University, Assiut Branch, Assiut (Egypt); Khalil, N.M. [Chemistry Department, Faculty of Science & Arts, Khullais, University of Jeddah, Jeddah (Saudi Arabia); Refractories, Ceramics and Building Materials Department, National Research Centre, 12311, Cairo (Egypt); Algamal, Yousif [Chemistry Department, Faculty of Science & Arts, Khullais, University of Jeddah, Jeddah (Saudi Arabia); Saleem, Qaid M.A. [Chemistry Department, Faculty of Science & Arts, Khullais, University of Jeddah, Jeddah (Saudi Arabia); Aden University, Shabwa (Yemen)

    2017-06-01

    Nanoparticles of Zirconia were prepared (ZrO{sub 2}) by the neutralization of zirconium oxychloride octahydrate (ZrOCl{sub 2}-8H{sub 2}O) (2M) and ammonia solution (2M) at pH 8. The ZrO{sub 2} crystalline state was revealed by X-ray diffraction (XRD). The analysis of Scanning electron microscopy (SEM) and Transmission Electron microscope (TEM) images reveals that the as-synthesized ZrO{sub 2} particles at firing temperature of 800 °C are uniform and of range of 30 nm. Increasing of the temperature up to 1100 °C leads to the increase in particle size and alters the powders shape due to agglomeration arose from zirconia calcination as well as the increase in particle size. The X-ray peak broadening analysis (XRDBA) was used in the estimation of the crystalline size. Williamson-Hall (W-H) analysis was applied successfully to determine the energy density, stress, and the strain values via uniform deformation model (UDM), uniform deformation stress model (UDSM) and uniform deformation energy density model (UDEDM). The mean of the strain root square was calculated. The different strain values obtained from these models predicting the zirconia isotropic behavior. In addition to that, the W-H analysis results were discussed in terms of that obtained by Scherrer’s relationship, SEM and TEM images. - Graphical abstract: XRD patterns for zirconia nano-particles at different calcined temperature. - Highlights: • Nanoparticles of Zirconia (ZrO{sub 2}) were synthesized. • The ZrO{sub 2} crystalline state was revealed by XRD, SEM and TEM. • SEM and TEM images reveals that the ZrO{sub 2} particles are uniform and relatively small. • Both blocky particles and the powders shape are affected by the firing temperature. • The crystalline sizes were estimated using X-ray peak broadening analysis (XRDBA).

  17. Ground penetrating radar geologic field studies of the ejecta of Barringer Meteorite Crater, Arizona, as a planetary analog

    Science.gov (United States)

    Russell, Patrick S.; Grant, John A.; Williams, Kevin K.; Carter, Lynn M.; Brent Garry, W.; Daubar, Ingrid J.

    2013-09-01

    penetrating radar (GPR) has been a useful geophysical tool in investigating a variety of shallow subsurface geological environments on Earth. Here we investigate the capabilities of GPR to provide useful geologic information in one of the most common geologic settings of planetary surfaces, impact crater ejecta. Three types of ejecta are surveyed with GPR at two wavelengths (400 MHz, 200 MHz) at Meteor Crater, Arizona, with the goal of capturing the GPR signature of the subsurface rock population. In order to "ground truth" the GPR characterization, subsurface rocks are visually counted and measured in preexisting subsurface exposures immediately adjacent to and below the GPR transect. The rock size-frequency distribution from 10 to 50 cm based on visual counts is well described by both power law and exponential functions, the former slightly better, reflecting the control of fragmentation processes during the impact-ejection event. GPR counts are found to overestimate the number of subsurface rocks in the upper meter (by a factor of 2-3x) and underestimate in the second meter of depth (0.6-1.0x), results attributable to the highly scattering nature of blocky ejecta. Overturned ejecta that is fractured yet in which fragments are minimally displaced from their complement fragments produces fewer GPR returns than well-mixed ejecta. The use of two wavelengths and division of results into multiple depth zones provides multiple aspects by which to characterize the ejecta block population. Remote GPR measurement of subsurface ejecta in future planetary situations with no subsurface exposure can be used to characterize those rock populations relative to that of Meteor Crater.

  18. Experimental interaction of magma and “dirty” coolants

    Science.gov (United States)

    Schipper, C. Ian; White, James D. L.; Zimanowski, Bernd; Büttner, Ralf; Sonder, Ingo; Schmid, Andrea

    2011-03-01

    The presence of water at volcanic vents can have dramatic effects on fragmentation and eruption dynamics, but little is known about how the presence of particulate matter in external water will further alter eruptions. Volcanic edifices are inherently “dirty” places, where particulate matter of multiple origins and grainsizes typically abounds. We present the results of experiments designed to simulate non-explosive interactions between molten basalt and various “coolants,” ranging from homogeneous suspensions of 0 to 30 mass% bentonite clay in pure water, to heterogeneous and/or stratified suspensions including bentonite, sand, synthetic glass beads and/or naturally-sorted pumice. Four types of data are used to characterise the interactions: (1) visual/video observations; (2) grainsize and morphology of resulting particles; (3) heat-transfer data from a network of eight thermocouples; and (4) acoustic data from three force sensors. In homogeneous coolants with ~20% sediment, heat transfer is by forced convection and conduction, and thermal granulation is less efficient, resulting in fewer blocky particles, larger grainsizes, and weaker acoustic signals. Many particles are droplet-shaped or/and “vesicular,” containing bubbles filled with coolant. Both of these particle types indicate significant hydrodynamic magma-coolant mingling, and many of them are rewelded into compound particles. The addition of coarse material to heterogeneous suspensions further slows heat transfer thus reducing thermal granulation, and variable interlocking of large particles prevents efficient hydrodynamic mingling. This results primarily in rewelded melt piles and inefficient distribution of melt and heat throughout the coolant volume. Our results indicate that even modest concentrations of sediment in water will significantly limit heat transfer during non-explosive magma-water interactions. At high concentrations, the dramatic reduction in cooling efficiency and increase in

  19. A fourth order PDE based fuzzy c- means approach for segmentation of microscopic biopsy images in presence of Poisson noise for cancer detection.

    Science.gov (United States)

    Kumar, Rajesh; Srivastava, Subodh; Srivastava, Rajeev

    2017-07-01

    For cancer detection from microscopic biopsy images, image segmentation step used for segmentation of cells and nuclei play an important role. Accuracy of segmentation approach dominate the final results. Also the microscopic biopsy images have intrinsic Poisson noise and if it is present in the image the segmentation results may not be accurate. The objective is to propose an efficient fuzzy c-means based segmentation approach which can also handle the noise present in the image during the segmentation process itself i.e. noise removal and segmentation is combined in one step. To address the above issues, in this paper a fourth order partial differential equation (FPDE) based nonlinear filter adapted to Poisson noise with fuzzy c-means segmentation method is proposed. This approach is capable of effectively handling the segmentation problem of blocky artifacts while achieving good tradeoff between Poisson noise removals and edge preservation of the microscopic biopsy images during segmentation process for cancer detection from cells. The proposed approach is tested on breast cancer microscopic biopsy data set with region of interest (ROI) segmented ground truth images. The microscopic biopsy data set contains 31 benign and 27 malignant images of size 896 × 768. The region of interest selected ground truth of all 58 images are also available for this data set. Finally, the result obtained from proposed approach is compared with the results of popular segmentation algorithms; fuzzy c-means, color k-means, texture based segmentation, and total variation fuzzy c-means approaches. The experimental results shows that proposed approach is providing better results in terms of various performance measures such as Jaccard coefficient, dice index, Tanimoto coefficient, area under curve, accuracy, true positive rate, true negative rate, false positive rate, false negative rate, random index, global consistency error, and variance of information as compared to other

  20. Identification and assessment of groundwater flow and storage components of the relict Schöneben Rock Glacier, Niedere Tauern Range, Eastern Alps (Austria)

    Science.gov (United States)

    Winkler, Gerfried; Wagner, Thomas; Pauritsch, Marcus; Birk, Steffen; Kellerer-Pirklbauer, Andreas; Benischke, Ralf; Leis, Albrecht; Morawetz, Rainer; Schreilechner, Marcellus G.; Hergarten, Stefan

    2016-06-01

    More than 2,600 relict rock glaciers are known in the Austrian Alps but the knowledge of their hydraulic properties is severely limited. The relict Schöneben Rock Glacier (Niedere Tauern Range, Austria), with an extension of 0.17 km2, was investigated based on spring data (2006-2014) and seismic refraction survey. Spring-discharge hydrographs and natural and artificial tracer data suggest a heterogeneous aquifer with a layered internal structure for the relict rock glacier. The discharge behavior exhibits a fast and a delayed flow component. The spring discharge responds to recharge events within a few hours but a mean residence time of several months can also be observed. The internal structure of the rock glacier (up to several tens of meters thick) consists of: an upper blocky layer with a few meters of thickness, which lacks fine-grained sediments; a main middle layer with coarse and finer-grained sediments, allowing for fast flow; and an approximately 10-m-thick basal till layer as the main aquifer body responsible for the base flow. The base-flow component is controlled by (fine) sandy to silty sediments with low hydraulic conductivity and high storage capacity, exhibiting a difference in hydraulic conductivity to the upper layer of about three orders of magnitude. The high storage capacity of relict rock glaciers has an impact on water resources management in alpine catchments and potentially regulates the risk of natural hazards such as floods and related debris flows. Thus, the results highlight the importance of such aquifer systems in alpine catchments.

  1. Contribution of 3-D electrical resistivity tomography for landmines detection

    Directory of Open Access Journals (Sweden)

    M. Metwaly

    2008-12-01

    Full Text Available Landmines are a type of inexpensive weapons widely used in the pre-conflicted areas in many countries worldwide. The two main types are the metallic and non-metallic (mostly plastic landmines. They are most commonly investigated by magnetic, ground penetrating radar (GPR, and metal detector (MD techniques. These geophysical techniques however have significant limitations in resolving the non-metallic landmines and wherever the host materials are conductive. In this work, the 3-D electric resistivity tomography (ERT technique is evaluated as an alternative and/or confirmation detection system for both landmine types, which are buried in different soil conditions and at different depths. This can be achieved using the capacitive resistivity imaging system, which does not need direct contact with the ground surface. Synthetic models for each case have been introduced using metallic and non-metallic bodies buried in wet and dry environments. The inversion results using the L1 norm least-squares optimization method tend to produce robust blocky models of the landmine body. The dipole axial and the dipole equatorial arrays tend to have the most favorable geometry by applying dynamic capacitive electrode and they show significant signal strength for data sets with up to 5% noise. Increasing the burial depth relative to the electrode spacing as well as the noise percentage in the resistivity data is crucial in resolving the landmines at different environments. The landmine with dimension and burial depth of one electrode separation unit is over estimated while the spatial resolutions decrease as the burial depth and noise percentage increase.

  2. Event sedimentation in low-latitude deep-water carbonate basins, Anegada passage, northeast Caribbean

    Science.gov (United States)

    Chaytor, Jason D.; ten Brink, Uri S.

    2015-01-01

    The Virgin Islands and Whiting basins in the Northeast Caribbean are deep, structurally controlled depocentres partially bound by shallow-water carbonate platforms. Closed basins such as these are thought to document earthquake and hurricane events through the accumulation of event layers such as debris flow and turbidity current deposits and the internal deformation of deposited material. Event layers in the Virgin Islands and Whiting basins are predominantly thin and discontinuous, containing varying amounts of reef- and slope-derived material. Three turbidites/sandy intervals in the upper 2 m of sediment in the eastern Virgin Islands Basin were deposited between ca. 2000 and 13 600 years ago, but do not extend across the basin. In the central and western Virgin Islands Basin, a structureless clay-rich interval is interpreted to be a unifite. Within the Whiting Basin, several discontinuous turbidites and other sand-rich intervals are primarily deposited in base of slope fans. The youngest of these turbidites is ca. 2600 years old. Sediment accumulation in these basins is low (−1) for basin adjacent to carbonate platform, possibly due to limited sediment input during highstand sea-level conditions, sediment trapping and/or cohesive basin walls. We find no evidence of recent sediment transport (turbidites or debris flows) or sediment deformation that can be attributed to the ca. M7.2 1867 Virgin Islands earthquake whose epicentre was located on the north wall of the Virgin Islands Basin or to recent hurricanes that have impacted the region. The lack of significant appreciable pebble or greater size carbonate material in any of the available cores suggests that submarine landslide and basin-wide blocky debris flows have not been a significant mechanism of basin margin modification in the last several thousand years. Thus, basins such as those described here may be poor recorders of past natural hazards, but may provide a long-term record of past oceanographic

  3. Lattice strain estimation for CoAl{sub 2}O{sub 4} nano particles using Williamson-Hall analysis

    Energy Technology Data Exchange (ETDEWEB)

    Aly, Kamal A., E-mail: kamalaly2001@gmail.com [Physics Department, Faculty of Science & Arts, Khulais, University of Jeddah, Jiddah (Saudi Arabia); Physics Department, Faculty of Science, Al-Azhar University, Assiut Branch, Assiut (Egypt); Khalil, N.M. [Chemistry Department, Faculty of Science & Arts, Khulais, University of Jeddah, Jiddah (Saudi Arabia); Refractories, Ceramics and Building Materials Department, National Research Centre, 12311 Cairo (Egypt); Algamal, Yousif [Chemistry Department, Faculty of Science & Arts, Khulais, University of Jeddah, Jiddah (Saudi Arabia); Saleem, Qaid M.A. [Chemistry Department, Faculty of Science & Arts, Khulais, University of Jeddah, Jiddah (Saudi Arabia); Chemistry Department, Faculty of Education, Aden University, Sabwa (Yemen)

    2016-08-15

    CoAl{sub 2}O{sub 4} nanoparticles were prepared via coprecipitation technique through mixing 1:1 M ratio of cobalt nitrate and aluminium nitrate solutions at pH 10. CoAl{sub 2}O{sub 4} crystalline phase was confirmed by X-ray diffraction. Scanning electron microscopy (SEM) result reveals that the particles of CoAl{sub 2}O{sub 4} fired at 900 °C were relatively small (21 nm) and uniform. Increased temperature to 1200 °C gives rise to blocky particles and changes in the powders shape, that because of agglomeration came from the calcination of CoAl{sub 2}O{sub 4}. Furthermore, the particle size increase with increasing the calcinated temperature. The crystalline sizes were evaluated by using X-ray peak broadening analysis suggested by Williamson-Hall (W-H) analysis. It was successfully applied for lattice strain and to calculate mechanical stress and energy density values using different three models namely uniform deformation model (UDM), uniform deformation stress model (UDSM) and uniform deformation energy density model (UDEDM). Also, the root mean square strain was determined. These models gave a different strain values which suggested an isotropic nature of the nanoparticles. Besides, the obtained results W-H analysis are in good agreement with that deduced from SEM analysis and Scherrer's formula. - Highlights: • CoAl{sub 2}O{sub 4} nanoparticles were prepared via coprecipitation technique. • CoAl{sub 2}O{sub 4} nanoparticles were characterized by SEM and XRD. • the lattice size and strain were investigated according to W-H analysis. • The latic size were investigated by W-H analysis, SEM and Sherrar's method. • The root mean square strain was determined.

  4. Effect of two-step intercritical annealing on microstructure and mechanical properties of hot-rolled medium manganese TRIP steel containing δ-ferrite

    International Nuclear Information System (INIS)

    Xu, Yun-bo; Hu, Zhi-ping; Zou, Ying; Tan, Xiao-dong; Han, Ding-ting; Chen, Shu-qing; Ma, De-gang; Misra, R.D.K.

    2017-01-01

    The microstructure-properties relationship, work-hardening behavior and retained austenite stability have been systematically investigated in a hot-rolled medium manganese transformation-induced-plasticity (TRIP) steel containing δ-ferrite subjected to one-step and two-step intercritical annealing. The steel exhibited tensile strength of 752 MPa and total elongation of 52.7% for one-step intercritical annealing at 740 °C, tensile strength of 954 MPa and total elongation of 39.2% in the case of intercritical quenching at 800 °C and annealing at 740 °C. The austenite obtained by two-step annealing mostly consists of refined lath structures and increased fraction of block-type particles existing at various kinds of sites, which is highly distinguished from those characterized by long lath morphology and small amounts of granular shape in one-step annealed samples. In spite of a higher C and Mn content in austenite and finer austenite laths, two-step annealing can lead to an active and continuous TRIP effect provided by a mixed blocky and lath-type austenitic structure with lower stability, contributing to a higher UTS. In contrast, one-step annealing gave rise to a less active but sustained TRIP effect given by the dominant lath-like austenite having higher stability, leading to a very high elongation. The further precipitation of vanadium carbides and the presence of both dislocation substructure and fine equiaxed grain in ferrite matrix facilitate the increase of yield strength after double annealing. - Highlights: • A novel two-step process was applied to a hot-rolled Fe-0.2C-6.5Mn-3Al steel. • The interplay between different microstructures and mechanical properties was studied. • Two-step annealing led to an active and continuous TRIP. • An outstanding combination of strength of 954 MPa and elongation of 39.2% was obtained.

  5. Comparison of the diagenetic and reservoir quality evolution between the anticline crest and flank of an Upper Jurassic carbonate gas reservoir, Abu Dhabi, United Arab Emirates

    Science.gov (United States)

    Morad, Daniel; Nader, Fadi H.; Gasparrini, Marta; Morad, Sadoon; Rossi, Carlos; Marchionda, Elisabetta; Al Darmaki, Fatima; Martines, Marco; Hellevang, Helge

    2018-05-01

    This petrographic, stable isotopic and fluid inclusion microthermometric study of the Upper Jurassic limestones of an onshore field, Abu Dhabi, United Arab Emirates (UAE) compares diagenesis in flanks and crest of the anticline. The results revealed that the diagenetic and related reservoir quality evolution occurred during three phases, including: (i) eogenesis to mesogenesis 1, during which reservoir quality across the field was either deteriorated or preserved by calcite cementation presumably derived from marine or evolved marine pore waters. Improvement of reservoir quality was due to the formation of micropores by micritization of allochems and creation of moldic/intragranular pores by dissolution of peloids and skeletal fragments. (ii) Obduction of Oman ophiolites and formation of the anticline of the studied field was accompanied by cementation by saddle dolomite and blocky calcite. High homogenization temperatures (125-175 °C) and high salinity (19-26 wt% NaCl eq) of the fluid inclusions, negative δ18OVPDB values (-7.7 to -2.9‰), saddle shape of dolomite, and the presence of exotic cements (i.e. fluorite and sphalerite) suggest that these carbonates were formed by flux of hot basinal brines, probably related to this tectonic compression event. (iii) Mesogenesis 2 during subsidence subsequent to the obduction event, which resulted in extensive stylolitization and cementation by calcite. This calcite cement occluded most of the remaining moldic and inter-/intragranular pores of the flank limestones (water zone) whereas porosity was preserved in the crest. This study contributes to: (1) our understanding of differences in the impact of diagenesis on reservoir quality evolution in flanks and crests of anticlines, i.e. impact of hydrocarbon emplacement on diagenesis, and (2) relating various diagenetic processes to burial history and tectonic events of foreland basins in the Arabian Gulf area and elsewhere.

  6. Synthesis and properties of Li2SnO3/polyaniline nanocomposites as negative electrode material for lithium-ion batteries

    International Nuclear Information System (INIS)

    Wang Qiufen; Huang Ying; Miao Juan; Zhao Yang; Wang Yan

    2012-01-01

    Highlights: ► Li 2 SnO 3 /polyaniline nanocomposite (40–50 nm) was synthesized by micro emulsion polymerization. ► Li 2 SnO 3 /PANI exhibits lower initial irreversible capacities than Li 2 SnO 3 . ► Its capacity retains 569.2 mAh g −1 after 50 cycles. - Abstract: The nanocomposites Li 2 SnO 3 /polyaniline (Li 2 SnO 3 /PANI) have been synthesized by a micro emulsion polymerization method. The structure, morphology and electrochemical properties of the as-prepared materials are characterized by XRD, FTIR, Raman, XPS, TGA, TEM and electrochemical measurements. Results show that Li 2 SnO 3 /PANI nanocomposites are composed of uniform and blocky nano-sized particles (40–50 nm) with clear lattice fringes. Electrochemical measurement suggests that Li 2 SnO 3 /PANI exhibits better cycling properties and lower initial irreversible capacities than Li 2 SnO 3 as negative electrodes materials for lithium-ion batteries. At a current density of 60 mA g −1 in the voltage about 0.05–2.0 V, the initial irreversible capacity of Li 2 SnO 3 /PANI is 563 mAh g −1 while it is 687.5 mAh g −1 to Li 2 SnO 3 . The capacity retained of Li 2 SnO 3 /PANI (569.2 mAh g −1 ) is higher than that of Li 2 SnO 3 (510.2 mAh g −1 ) after 50 cycles. The PANI in the Li 2 SnO 3 /PANI nanocomposites can buffer the released stress caused by the drastic volume variation during the alloying/de-alloying process of Li–Sn.

  7. Effect of two-step intercritical annealing on microstructure and mechanical properties of hot-rolled medium manganese TRIP steel containing δ-ferrite

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Yun-bo [State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819, People' s Republic China (China); Hu, Zhi-ping, E-mail: huzhiping900401@126.com [State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819, People' s Republic China (China); Zou, Ying; Tan, Xiao-dong; Han, Ding-ting; Chen, Shu-qing [State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819, People' s Republic China (China); Ma, De-gang [Tangshan Iron and Steel Company, Tangshan 063000, People' s Republic China (China); Misra, R.D.K. [Laboratory for Excellence in Advanced Steel Research, Department of Metallurgical, Materials and Biomedical Engineering, University of Texas at El Paso, TX 79968 (United States)

    2017-03-14

    The microstructure-properties relationship, work-hardening behavior and retained austenite stability have been systematically investigated in a hot-rolled medium manganese transformation-induced-plasticity (TRIP) steel containing δ-ferrite subjected to one-step and two-step intercritical annealing. The steel exhibited tensile strength of 752 MPa and total elongation of 52.7% for one-step intercritical annealing at 740 °C, tensile strength of 954 MPa and total elongation of 39.2% in the case of intercritical quenching at 800 °C and annealing at 740 °C. The austenite obtained by two-step annealing mostly consists of refined lath structures and increased fraction of block-type particles existing at various kinds of sites, which is highly distinguished from those characterized by long lath morphology and small amounts of granular shape in one-step annealed samples. In spite of a higher C and Mn content in austenite and finer austenite laths, two-step annealing can lead to an active and continuous TRIP effect provided by a mixed blocky and lath-type austenitic structure with lower stability, contributing to a higher UTS. In contrast, one-step annealing gave rise to a less active but sustained TRIP effect given by the dominant lath-like austenite having higher stability, leading to a very high elongation. The further precipitation of vanadium carbides and the presence of both dislocation substructure and fine equiaxed grain in ferrite matrix facilitate the increase of yield strength after double annealing. - Highlights: • A novel two-step process was applied to a hot-rolled Fe-0.2C-6.5Mn-3Al steel. • The interplay between different microstructures and mechanical properties was studied. • Two-step annealing led to an active and continuous TRIP. • An outstanding combination of strength of 954 MPa and elongation of 39.2% was obtained.

  8. Genesis of natural hydraulic fractures as an indicator of basin inversion

    Science.gov (United States)

    Meng, Qingfeng; Hooker, John; Cartwright, Joe

    2017-09-01

    Satin spar (fibrous gypsum) veins, which occur in evaporite basins worldwide, provide significant insights into host rock deformation and fluid flow, although the genetic mechanism remains obscure. Satin spar veins in the red marls of the Triassic Mercia Mudstone of the Bristol Channel Basin were characterized in the context of regional and local setting. The vein network in the Keuper Marl (lower Mercia) exhibits a lack of systematic cross-cutting between three distinct vein sets. Two sets of veins are observed in the overlying Tea Green Marl, with one set clearly crossing the other. The gypsum veins commonly contain a blocky median zone of multiple thin bands of host-rock inclusions and alabastrine gypsum crystals, exhibiting crack-seal patterns. Fibrous zones on either side of the median zone consist of pure parallel-aligned gypsum fibres that are oblique to vein walls, indicating a hybrid shear-extensional mode of vein widening. Veins developed within reverse-reactivated faults contain fibre lineations in the median zones and also on vein surfaces, suggesting a minimum of two phases of fault slip. The veins are interpreted to have formed as a result of overpressure in the low-permeability mudstones by tectonic compression during basin inversion, giving rise to the median zone. Growth of gypsum fibres commenced when the initial fractures were completely sealed. The timing of vein formation is suggested to be Miocene, based on cross-cutting relationships with folds formed during the latest phase of basin inversion. Because the fractures initiated in response to fluid overpressures, they provide a useful analog to subsurface hydraulic fracture systems in low-permeability rocks subjected to tectonic compression. The fibrous widening of the veins post-dates their initiation and led to continued propagation and increased connectivity.

  9. Effect of processing parameters on the formation of Cf/LAS composites/Ag−Cu−Ti/TC4 brazed joint

    International Nuclear Information System (INIS)

    Liu, Duo; Niu, Hongwei; Liu, Jihou; Song, Xiaoguo; Xia, Long; Feng, Jicai

    2016-01-01

    C f /LAS composites were successfully jointed to TC4 alloy with Ag−Cu−Ti filler by vacuum brazing. The interfacial microstructure of TC4/C f /LAS composites joints was characterized by employing scanning electron microscope (SEM), energy dispersive spectrometer (EDS), X-diffraction (XRD) and transmission electron microscopy (TEM). The determination of the thin interfacial reaction layer (TiSi 2 + TiC layer) was realized by TEM. The effect of holding time on the interfacial microstructure and shear strength were investigated. With the increasing holding time, the thickness of diffusion layer, Ti 3 Cu 4 layer, and TiSi 2 + TiC layer increased obviously, on the contrary, that of Ti−Cu intermetallic compound layers decreased gradually. Besides, blocky Ti 3 Cu 4 phase was coarsened when the joint was brazed at 890 °C for 20 min, which deteriorated the mechanical properties of the joint dramatically. The interfacial evolution of TC4/C f /LAS composites joint and the formation of TiSi 2 , TiC, Ti 3 Cu 4 , TiCu and Ti 2 Cu phases were expounded. The maximum shear strength of 26.4 MPa was obtained when brazed at 890 °C for 10 min. - Highlights: •The thin interface reaction layer was determined to be TiSi 2 + TiC layer by TEM. •Holding time had influence on the interfacial microstructure and joint properties. •Microstructural evolution mechanism and reactions of brazed joints were expounded.

  10. Autographa californica multiple nucleopolyhedrovirus ac75 is required for egress of nucleocapsids from the nucleus and formation of de novo intranuclear membrane microvesicles.

    Directory of Open Access Journals (Sweden)

    Ya-Jun Guo

    Full Text Available In this study, Autographa californica multiple nucleopolyhedrovirus ac75 was functionally characterized. Ac75 has homologs in all sequenced genomes of alphabaculoviruses, betabaculoviruses, and gammabaculoviruses. It was determined to encode a protein that is associated with the nucleocapsid of budded virus and with both envelope and nucleocapsids of occlusion-derived virus. Sf9 cells transfected by an ac75-knockout bacmid resulted in the infection being restricted to single cells. No budded virus were detected although viral DNA replication and late gene expression were unaffected. Electron microscopy revealed that the virogenic stroma, nucleocapsids and occlusion bodies appeared normal in the cells transfected by an ac75-knockout bacmid. However, the nucleocapsids were unenveloped, the occlusion bodies did not contain any virions or nucleocapsids, and no nucleocapsids were found outside the nucleus or spanning the nuclear membrane. In addition, de novo intranuclear membrane microvesicles that are the precursor of occlusion-derived virus envelopes were absent in the nuclei of transfected cells. Confocal microscopy showed that AC75 protein appeared in the cytoplasm as early as 6 hours post infection. It localized to the ring zone at the periphery of the nucleus from 15 to 24 hours post infection and demonstrated light blocky cloud-like distribution in the center of the nucleus. AC75 was found to co-immunoprecipitate with BV and ODV associated envelope protein ODV-E25. The data from this study suggest that ac75 is essential for induction of the intranuclear membrane microvesicles, it appears to be required for the intranuclear envelopment of nucleocapsids, and is also essential for egress of nucleocapsids from the nuclei, in infected cells.

  11. Interdisciplinary study of post-glacial faulting in the Lansjaerv area, Northern Sweden 1986-1988

    International Nuclear Information System (INIS)

    Baeckblom, G.; Stanfors, R.

    1989-12-01

    Post-glacial faults have been recognized in the northern Baltic shield for several decades. It is important to evaluate whether such neotectonic movements can lead to new fracturing or decisively alter the geohydrological or geohydrochemical situation around a final repository for spent nuclear fuel. The post-glacial Lansjaerv fault was chosen for interdisciplinary study because of its relative accessibility. The goals of the study were to assess the mechanisms that caused present day scarps, to clarify the extent of any recent fracturing and to clarify the extent of any ongoing movements. All these objectives were reasonable met through a series of studies. This report describes achievements that have been gained since the study was initiated by SKB 1986. Analysis of geology and geophysics over a 150x200 km region supplemented with seismic networks and field studies at outcrops and trenches set a framework for a cored borehole down to depth of 500 m at the fault. The core has been studied in detail with respect to fracture-infillings in order to analyse mineralogical and geochemical alteration. The borehole has been logged for geophysics, stress, hydraulic conductivity, groundwater pressure and the chemical constituents of the groundwater. Numerical modelling has been undertaken in order to understand the effects of glaciation on the behaviour of a blocky rock mass. Several general conclusions have been made by the interdisciplinary research group. One of the major conclusions is that pre-existing old structures were reactivated by tectonic movements, possibly triggered by deglaciation. In spite of a major earthquake that may have occurred during the deglaciation, and in spite of the anomalous tectonic setting compared to study-sites within SKB:s site investigation programme, the hydraulic conductivity and groundwater chemistry are comparable with results from those sites. (83 figs., 15 tabs., 150 refs.)

  12. Coupling effects of tungsten and molybdenum on microstructure and stress-rupture properties of a nickel-base cast superalloy

    Directory of Open Access Journals (Sweden)

    Tongjin Zhou

    2018-02-01

    Full Text Available In order to comprehensively understand the forming mechanism of abnormal phases solidified in a nickel-base cast superalloy with additives of tungsten and molybdenum, the coupling effects of W and Mo on the microstructure and stress-rupture properties were investigated in this paper. The results indicated that the precipitation of primary α-(W, Mo phase depended tremendously on the amount of W and Mo addition. When the total amount of W and Mo was greater than 5.79 at%, α-(W, Mo phase became easily precipitated in the alloy. With increasing of Mo/W ratio, the dendrite-like α-(W, Mo phases were apt to convert into small bars or blocky-like phases at the vicinities of γ′/γ eutectic. The morphological changes of α-(W, Mo phase can be interpreted as the non-equilibrium solidification of W and Mo in the alloy. Since the large sized α-(W, Mo phase has detrimental effects on stress-rupture properties in as-cast conditions, secondary cracks may mainly initiate at and then propagate along the interfaces of brittle phases and soft matrix. During exposing at 1100 ℃ for 1000 h, the α-(W, Mo phases transformed gradually into bigger and harder M6C carbide, which results in decreasing of stress-rupture properties of the alloy. Finally, the alloy with an addition of 14W-1Mo(wt% maintained the longest stress lives at high temperatures and therefore it revealed the best microstructure stability after 1100 ℃/1000 h thermal exposure. Keywords: Superalloy, Tungsten and molybdenum, Cast, Microstructure, Stress-rupture properties

  13. A combined field/remote sensing approach for characterizing landslide risk in coastal areas

    Science.gov (United States)

    Francioni, Mirko; Coggan, John; Eyre, Matthew; Stead, Doug

    2018-05-01

    Understanding the key factors controlling slope failure mechanisms in coastal areas is the first and most important step for analyzing, reconstructing and predicting the scale, location and extent of future instability in rocky coastlines. Different failure mechanisms may be possible depending on the influence of the engineering properties of the rock mass (including the fracture network), the persistence and type of discontinuity and the relative aspect or orientation of the coastline. Using a section of the North Coast of Cornwall, UK, as an example we present a multi-disciplinary approach for characterizing landslide risk associated with coastal instabilities in a blocky rock mass. Remotely captured terrestrial and aerial LiDAR and photogrammetric data were interrogated using Geographic Information System (GIS) techniques to provide a framework for subsequent analysis, interpretation and validation. The remote sensing mapping data was used to define the rock mass discontinuity network of the area and to differentiate between major and minor geological structures controlling the evolution of the North Coast of Cornwall. Kinematic instability maps generated from aerial LiDAR data using GIS techniques and results from structural and engineering geological surveys are presented. With this method, it was possible to highlight the types of kinematic failure mechanism that may generate coastal landslides and highlight areas that are more susceptible to instability or increased risk of future instability. Multi-temporal aerial LiDAR data and orthophotos were also studied using GIS techniques to locate recent landslide failures, validate the results obtained from the kinematic instability maps through site observations and provide improved understanding of the factors controlling the coastal geomorphology. The approach adopted is not only useful for academic research, but also for local authorities and consultancy's when assessing the likely risks of coastal instability.

  14. Metal uptake by corn grown on media treated with particle-size fractionated biosolids

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Weiping [Department of Environmental Sciences, University of California, Riverside, CA 92521 (United States)], E-mail: chenweip@yahoo.com.cn; Chang, Andrew C.; Wu, Laosheng [Department of Environmental Sciences, University of California, Riverside, CA 92521 (United States); Zhang, Yongsong [School of Environmental and Natural Resources Sciences, Zhejiang University, Hangzhou, Zhejiang, 31009 (China)

    2008-03-15

    Particle-size of biosolids may affect plant uptake of heavy metals when the biosolids are land applied. In this study, corn (Zea mays L.) was grown on sand media treated with biosolids to study how particle-size of biosolids affected the plant uptake of cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni), lead (Pb), and zinc (Zn). Two biosolids, the Nu-Earth biosolids and the Los Angeles biosolids, of dissimilar surface morphology were utilized. The former exhibited a porous and spongy structure and had considerably greater specific surface area than that of the latter, which was granular and blocky. The specific surface area of the Los Angeles biosolids was inversely proportional to its particle-size, while that of Nu-Earth biosolids did not change significantly with particle-size. For each biosolid, the metal concentrations were not affected by particle sizes. The biomass yields of plants grown on the treated media increased as the biosolid particle-size decreased, indicating that plant uptake of nutrients from biosolids was dependent on interactions at the root-biosolids interface. The effect of particle-size on a metal's availability to plants was element-specific. The uptake rate of Cd, Zn, Cu, and Ni was correlated with the surface area of the particles, i.e., smaller particles having higher specific area provided greater root-biosolids contact and resulted in enhanced uptake of Cd and Zn and slightly less increased uptake of Cu and Ni. The particle morphology of biosolids had limited influence on the plant tissue concentrations of Cr and Pb. For both types of biosolids, total metal uptake increased as biosolid particle-size decreased. Our research indicates that biosolid particle-size distribution plays a deciding role in plant uptake of heavy metals when they are land applied.

  15. Genesis of Soils Formed from Mafic Igneous Rock in the Atlantic Forest Environment

    Directory of Open Access Journals (Sweden)

    Adailde do Carmo Santos

    2016-01-01

    Full Text Available ABSTRACT Different parent materials participate in the formation of soils in the hilly landscape of “Mar de Morros” in the Atlantic Forest environment. Those derived from mafic igneous rock (gabbro frequently show erosion problems because of land use, which is aggravated by the mountainous relief and soil attributes. This study evaluated the main pedogenic processes of soils formed from mafic igneous rock (gabbro in a toposequence in Pinheiral (RJ by characterizing physical, chemical, mineralogical and micromorphological attributes. The profiles are located at different sections in the toposequence: summit (P1, shoulder (P2, backslope (P3 and footslope (P4.They were classified according to the Brazilian System of Soil Classification (SiBCS and correlated to Soil Taxonomy. The soil morphology of profiles P2, P3 and P4 is expressed by a brownish-red color, blocky structure with high to moderate development, clay films and clay loam to clay texture, with a textural B horizon. P1 shows less development, with a shallow profile and the sequence of horizons A-C-Cr. The soils have a slightly low degree of weathering, identified by the presence of pyroxenes and feldspars in the sand fraction and montorillonite in the clay fraction; the sum of bases is from 15 to 24 cmolc kg-1; and cation exchange capacity (CEC is from 12 to 22 cmolc kg-1. A significant presence of clay skins was observed in the field and was confirmed by thin section analysis, which showed features such as argillans, ferriargillans and iron nodules. The soil profile at the summit (P1 was classified as Neossolo Regolítico Órtico (Typic Udorthents, and the other profiles as Chernossolo Argilúvicos Órticos (Typic Argiudolls.

  16. FORMATION OF CALCITE AND SILICA FROM PERCOLATION IN A HYDROLOGICALLY UNSATURATED SETTING, YUCCA MOUNTAIN, NEVADA

    International Nuclear Information System (INIS)

    Paces, J.B.; Whelan, J.F.; Peterman, Z.E.; Marshall, B.D.

    2000-01-01

    Geological, mineralogical, chemical, and isotopic evidence from coatings of calcite and silica on open fractures and lithophysal cavities within welded tuffs at Yucca Mountain indicate an origin from meteoric water percolating through a thick (500 to 700 m) unsaturated zone (UZ) rather than from pulses of ascending ground water. Geologic evidence for a UZ setting includes the presence of coatings in only a small percentage of cavities, the restriction of coatings to fracture footwalls and cavity floors, and an absence of mineral high-water marks indicative of water ponding. Systematic mineral sequences (early calcite, followed by chalcedony with minor quartz and fluorite, and finally calcite with intercalated opal forming the bulk of the coatings) indicate progressive changes in UZ conditions through time, rather than repeated saturation by flooding. Percolation under the influence of gravity also results in mineral textures that vary between steeply dipping sites (thinner coatings of blocky calcite) and shallowly dipping sites (thicker coatings of coarse, commonly bladed calcite, with globules and sheets of opal). Micrometer-scale growth banding in both calcite and opal reflects slow average growth rates (scale of mm/m.y.) over millions of years rather than only a few rapidly deposited growth episodes. Isotopic compositions of C, O, Sr, and U from calcite and opal indicate a percolation-modified meteoric water source, and collectively refute a deeper ground-water source. Chemical and isotopic variations in coatings also indicate long-term evolution of water compositions. Although some compositional changes are related to shifts in climate, growth rates in the deeper UZ are buffered from large changes in meteoric input. Coatings most likely formed from films of water flowing down connected fracture pathways. Mineral precipitation is consistent with water vapor and carbon dioxide loss from films at very slow rates. Data collectively indicate that mineral coatings

  17. 3D dictionary learning based iterative cone beam CT reconstruction

    Directory of Open Access Journals (Sweden)

    Ti Bai

    2014-03-01

    Full Text Available Purpose: This work is to develop a 3D dictionary learning based cone beam CT (CBCT reconstruction algorithm on graphic processing units (GPU to improve the quality of sparse-view CBCT reconstruction with high efficiency. Methods: A 3D dictionary containing 256 small volumes (atoms of 3 × 3 × 3 was trained from a large number of blocks extracted from a high quality volume image. On the basis, we utilized cholesky decomposition based orthogonal matching pursuit algorithm to find the sparse representation of each block. To accelerate the time-consuming sparse coding in the 3D case, we implemented the sparse coding in a parallel fashion by taking advantage of the tremendous computational power of GPU. Conjugate gradient least square algorithm was adopted to minimize the data fidelity term. Evaluations are performed based on a head-neck patient case. FDK reconstruction with full dataset of 364 projections is used as the reference. We compared the proposed 3D dictionary learning based method with tight frame (TF by performing reconstructions on a subset data of 121 projections. Results: Compared to TF based CBCT reconstruction that shows good overall performance, our experiments indicated that 3D dictionary learning based CBCT reconstruction is able to recover finer structures, remove more streaking artifacts and also induce less blocky artifacts. Conclusion: 3D dictionary learning based CBCT reconstruction algorithm is able to sense the structural information while suppress the noise, and hence to achieve high quality reconstruction under the case of sparse view. The GPU realization of the whole algorithm offers a significant efficiency enhancement, making this algorithm more feasible for potential clinical application.-------------------------------Cite this article as: Bai T, Yan H, Shi F, Jia X, Lou Y, Xu Q, Jiang S, Mou X. 3D dictionary learning based iterative cone beam CT reconstruction. Int J Cancer Ther Oncol 2014; 2(2:020240. DOI: 10

  18. New insights into Capsicum spp relatedness and the diversification process of Capsicum annuum in Spain.

    Science.gov (United States)

    González-Pérez, Susana; Garcés-Claver, Ana; Mallor, Cristina; Sáenz de Miera, Luis E; Fayos, Oreto; Pomar, Federico; Merino, Fuencisla; Silvar, Cristina

    2014-01-01

    The successful exploitation of germplasm banks, harbouring plant genetic resources indispensable for plant breeding, will depend on our ability to characterize their genetic diversity. The Vegetable Germplasm Bank of Zaragoza (BGHZ) (Spain) holds an important Capsicum annuum collection, where most of the Spanish pepper variability is represented, as well as several accessions of other domesticated and non-domesticated Capsicum spp from all over the five continents. In the present work, a total of 51 C. annuum landraces (mainly from Spain) and 51 accessions from nine Capsicum species maintained at the BGHZ were evaluated using 39 microsatellite (SSR) markers spanning the whole genome. The 39 polymorphic markers allowed the detection of 381 alleles, with an average of 9.8 alleles per locus. A sizeable proportion of alleles (41.2%) were recorded as specific alleles and the majority of these were present at very low frequencies (rare alleles). Multivariate and model-based analyses partitioned the collection in seven clusters comprising the ten different Capsicum spp analysed: C. annuum, C. chinense, C. frutescens, C. pubescens, C. bacatum, C. chacoense and C. eximium. The data clearly showed the close relationships between C. chinense and C. frutescens. C. cardenasii and C. eximium were indistinguishable as a single, morphologically variable species. Moreover, C. chacoense was placed between C. baccatum and C. pubescens complexes. The C. annuum group was structured into three main clusters, mostly according to the pepper fruit shape, size and potential pungency. Results suggest that the diversification of C. annuum in Spain may occur from a rather limited gene pool, still represented by few landraces with ancestral traits. This ancient population would suffer from local selection at the distinct geographical regions of Spain, giving way to pungent and elongated fruited peppers in the South and Center, while sweet blocky and triangular types in Northern Spain.

  19. Electrical transport properties in Co nanocluster-assembled granular film

    Science.gov (United States)

    Zhang, Qin-Fu; Wang, Lai-Sen; Wang, Xiong-Zhi; Zheng, Hong-Fei; Liu, Xiang; Xie, Jia; Qiu, Yu-Long; Chen, Yuanzhi; Peng, Dong-Liang

    2017-03-01

    A Co nanocluster-assembled granular film with three-dimensional cross-connection paralleled conductive paths was fabricated by using the plasma-gas-condensation method in a vacuum environment. The temperature-dependent longitudinal resistivity and anomalous Hall effect of this new type granular film were systematically studied. The longitudinal resistivity of the Co nanocluster-assembled granular film first decreased and then increased with increasing measuring temperature, revealing a minimum value at certain temperature, T min . In a low temperature region ( T governed the electrical transport process, and the temperature coefficient of resistance (TCR) showed an insulator-type behavior. The thermal fluctuation-induced tunneling conduction progressively increased with increasing temperature, which led to a decrease in the longitudinal resistivity. In a high temperature region, the TCR showed a metallic-type behavior, which was primarily attributed to the temperature-dependent scattering. Different from the longitudinal resistivity behavior, the saturated anomalous Hall resistivity increased monotonically with increasing measuring temperature. The value of the anomalous Hall coefficient ( R S ) reached 2.3 × 10-9 (Ω cm)/G at 300 K, which was about three orders of magnitude larger than previously reported in blocky single-crystal Co [E. N. Kondorskii, Sov. Phys. JETP 38, 977 (1974)]. Interestingly, the scaling relation ( ρx y A ∝ ρx x γ ) between saturated anomalous Hall resistivity ( ρx y A ) and longitudinal resistivity ( ρ x x ) was divided into two regions by T min . However, after excluding the contribution of tunneling, the scaling relation followed the same rule. The corresponding physical mechanism was also proposed to explain these phenomena.

  20. Butt Welding of 2205/X65 Bimetallic Sheet and Study on the Inhomogeneity of the Properties of the Welded Joint

    Science.gov (United States)

    Gou, Ning-Nian; Zhang, Jian-Xun; Wang, Jian-Long; Bi, Zong-Yue

    2017-04-01

    The explosively welded 2205 duplex stainless steel/X65 pipe steel bimetallic sheets were butt jointed by multilayer and multi-pass welding (gas tungsten arc welding for the flyer and gas metal arc welding for the transition and parent layers of the bimetallic sheets). The microstructure and mechanical properties of the welded joint were investigated. The results showed that in the thickness direction, microstructure and mechanical properties of the welded joint exhibited obvious inhomogeneity. The microstructures of parent filler layers consisted of acicular ferrite, widmanstatten ferrite, and a small amount of blocky ferrite. The microstructure of the transition layer and flyer layer consisted of both austenite and ferrite structures; however, the transition layer of weld had a higher volume fraction of austenite. The results of the microhardness test showed that in both weld metal (WM) and heat-affected zone (HAZ) of the parent filler layers, the average hardness decreased with the increasing (from parent filler layer 1 to parent filler layer 3) welding heat input. The results of hardness test also indicated that the hardness of the WM and the HAZ for the flyer and transition layers was equivalent. The tensile test combined with Digital Specklegram Processing Technology demonstrated that the fracturing of the welded joint started at the HAZ of the flyer, and then the fracture grew toward the base metal of the parent flyer near the parent HAZ. The stratified impact test at -5 °C showed that the WM and HAZ of the flyer exhibited lower impact toughness, and the fracture mode was ductile and brittle mixed fracture.

  1. Effects of confinement on rock mass modulus: A synthetic rock mass modelling (SRM study

    Directory of Open Access Journals (Sweden)

    I. Vazaios

    2018-06-01

    Full Text Available The main objective of this paper is to examine the influence of the applied confining stress on the rock mass modulus of moderately jointed rocks (well interlocked undisturbed rock mass with blocks formed by three or less intersecting joints. A synthetic rock mass modelling (SRM approach is employed to determine the mechanical properties of the rock mass. In this approach, the intact body of rock is represented by the discrete element method (DEM-Voronoi grains with the ability of simulating the initiation and propagation of microcracks within the intact part of the model. The geometry of the pre-existing joints is generated by employing discrete fracture network (DFN modelling based on field joint data collected from the Brockville Tunnel using LiDAR scanning. The geometrical characteristics of the simulated joints at a representative sample size are first validated against the field data, and then used to measure the rock quality designation (RQD, joint spacing, areal fracture intensity (P21, and block volumes. These geometrical quantities are used to quantitatively determine a representative range of the geological strength index (GSI. The results show that estimating the GSI using the RQD tends to make a closer estimate of the degree of blockiness that leads to GSI values corresponding to those obtained from direct visual observations of the rock mass conditions in the field. The use of joint spacing and block volume in order to quantify the GSI value range for the studied rock mass suggests a lower range compared to that evaluated in situ. Based on numerical modelling results and laboratory data of rock testing reported in the literature, a semi-empirical equation is proposed that relates the rock mass modulus to confinement as a function of the areal fracture intensity and joint stiffness. Keywords: Synthetic rock mass modelling (SRM, Discrete fracture network (DFN, Rock mass modulus, Geological strength index (GSI, Confinement

  2. The First USGS Global Geologic Map of Europa

    Science.gov (United States)

    Leonard, E. J.; Patthoff, D. A.; Senske, D.; Collins, G. C.

    2017-12-01

    Understanding the global scale geology of Europa is paramount to gaining insight into the potential habitability of this icy world. To this end, work is ongoing to complete a global geological map at the scale of 1:15 million that incorporates data at all resolutions collected by the Voyager and Galileo missions. The results of this work will aid the Europa Clipper mission, now in formulation, by providing a framework for collaborative and synergistic science investigations. To understand global geologic and tectonic relations, a total of 10 geologic units have been defined. These include: Low Albedo Ridge Material (lam)—low albedo material that irregularly surrounds large (>20 km) ridge structures; Ridged plains (pr)—distributed over all latitudes and characterized by subparallel to cross-cutting ridges and troughs visible at high resolution (material (b)—linear to curvilinear zones with a distinct, abrupt albedo change from the surrounding region; Crater material (c), Continuous Crater Ejecta (ce) and Discontinuous Crater Ejecta (dce)—features associated with impact craters including the site of the impact, crater material, and the fall-out debris respectively; Low Albedo Chaos (chl), Mottled Albedo Chaos (chm) and High Albedo Chaos (chh)—disrupted terrain with a relatively uniform low albedo, patchy/variegated albedo, and uniform high albedo appearance respectively; Knobby Chaos (chk) - disrupted terrain with rough and blocky texture occurring in the high latitudes. In addition to the geologic units, our mapping also includes structural features—Ridges, Cycloids, Undifferentiated Linea, Crater Rims, Depression Margins, Dome Margins and Troughs. We also introduce a point feature (at the global scale), Microchaos, to denote small (material. The completed map will constrain the distribution of different Europa terrains and provide a general stratigraphic framework to assess the geologic history of Europa from the regional to the global scale. Here, we

  3. Geology and hydrogeology of the Dammam Formation in Kuwait

    Science.gov (United States)

    Al-Awadi, E.; Mukhopadhyay, A.; Al-Senafy, M. N.

    The Dammam Formation of Middle Eocene age is one of the major aquifers containing useable brackish water in Kuwait. Apart from the paleokarst zone at the top, the Dammam Formation in Kuwait consists of 150-200m of dolomitized limestone that is subdivided into three members, on the basis of lithology and biofacies. The upper member consists of friable chalky dolomicrite and dolomite. The middle member is mainly laminated biomicrite and biodolomicrite. The lower member is nummulitic limestone with interlayered shale toward the base. Geophysical markers conform to these subdivisions. Core analyses indicate that the upper member is the most porous and permeable of the three units, as confirmed by the distribution of lost-circulation zones. The quality of water in the aquifer deteriorates toward the north and east. A potentiometric-head difference exists between the Dammam Formation and the unconformably overlying Kuwait Group; this difference is maintained by the presence of an intervening aquitard. Résumé La formation de Damman, d'âge Éocène moyen, est l'un des principaux aquifères du Koweit, contenant de l'eau saumâtre utilisable. A part dans sa partie supérieure où existe un paléokarst, la formation de Damman au Koweit est constituée par 150 à 200m de calcaires dolomitisés, divisés en trois unités sur la base de leur lithologie et de biofaciès. L'unité supérieure est formée d'une dolomicrite crayeuse et friable et d'une dolomie. L'unité médiane est pour l'essentiel une biomicrite laminée et une biodolomicrite. L'unité inférieure est un calcaire nummulitique avec des intercalations argileuses vers la base. Les marqueurs géophysiques sont conformes à ces subdivisions. Les analyses de carottes montrent que l'unité supérieure est la plus poreuse et la plus perméable des trois. La répartition des zones d'écoulement souterrain confirment ces données. La qualité de l'eau dans l'aquifère se dégrade en direction du nord et de l'est. Une

  4. Petrographic and geochemical analysis of the Givetian-Frasnian sandstones in the Kuh-e-Tizi section, southeastern Central Iran

    Science.gov (United States)

    Hejazi, S. H.; Adabi, M. H.; Moussavi Harami, S. R.; Khosro Tehrani, K.

    2009-04-01

    The Givetian-Frasnian sandstones at the type section of Zarand Formation, sensu Wendt et al. (2002), unconformably overlie the Upper Cambrian Kuhbanan and underlie the Lower Carboniferous Hutk Formations respectively, in southeastern Central Iran. Petrographical data show that these sandstones are well-sorted and sub-angular to rounded grains quartzarenite. They are highly enriched in quartz, but poor in feldspar, lithic fragments and heavy minerals. Diagenetic features include physical and chemical compactions (straight, concavo-convex, sutured grain contacts and pressure solution of quartz grain), reduction of the pore space through rearrangements, and cementation (mostly silica, as quartz overgrowth). The provenance and tectonic setting of these sandstones have been interpreted using integrated petrographic and geochemical data. Petrographic analysis using standard methods (Basu et al., 1975; Dickinson et al., 1983) revealed that mono and poly-crystalline quartz grains have been derived from plutonic rocks of an interior cratonic setting. Elemental analysis and their ratios used for provenance studies (Th/Sc & La/Sc) which are similar to sediments derived from weathering of mostly felsic rocks (Amstrong-Altrin et al., 2004). Values representing chemical index of alteration (CIA) and the plagioclase index of alteration (PIA) range from 44.24 to 83.43, with an average of 69.96, and from 42.98 to 92.56, with an average of 75.8, respectively. However, most samples have values greater than 60, suggesting moderate to high weathering in the source area or during transportation prior to deposition. Major and trace element concentrations indicated a depositional setting in a passive continental margin, resembling those defined by Bhatia (1983), Bhatia & Crook (1986), Roser & Korsch (1986) and Kroonenberg (1994). Therefore, it can be concluded that these sandstones have been derived from stable cratonic setting. Refrences: Amstrong-Altrin, J.S., Lee, Y.I., Verma, S

  5. Studies of quaternary deposits in Olkiluoto in 2004; Maaperaetutkimukset tutkimuskaivannoissa TKB ja TK9 Olkiluodossa 2004

    Energy Technology Data Exchange (ETDEWEB)

    Huhta, P. [Geological Survey of Finland, Espoo (Finland)

    2005-04-15

    The study sections (trenches) TK 8 and TK 9 in Olkiluoto were studied according to the contract in autumn 2004. The investigations were carried out in three phases as the excavation progressed. Samples for grain size determinations were taken from vertical profiles, placed 25 m apart along the trench, with the profiles extending from the soil surface down to bedrock or, if the bedrock was covered with water, to the water table. Between 6 and 7 kg of sediment was taken in a bucket with a shovel and placed in plastic bags for transport to the laboratory. The samples were first dried in the laboratory after which they were sieved. In addition, grain size distribution of the < 63 {mu}m fraction was analyzed with the Micromeritics 5000 ET Sedigraph. Sedimentological observations of the sampling profiles were documented in field by drawing (on a field observation form) and the profiles were photographed using a digital camera. In addition, the excavated sections were photographed along their whole length. The length of the TK 8 trench is approximately 730 m and 30 profiles were sampled from it. The height of the profiles varied from 6 m to 0.8 m with an average of 2.6 m. The till in the trench TK 8 is classified as having a normal amount of cobbles and boulders with the size of the larger clasts varying from 6 to 60 cm. The clasts are normally rounded or sub-angular. Both the size and number of cobbles increases with depth, as does their angularity. In places the till is overlain by postglacial clays/silts and littoral sands. With the exception of one sample, all samples from the TK 8 section can be classified as sandy tills based on the d50 grain size. According to the guidelines for mapping of Quatemary deposits one third of the samples is classified as fine-grained tills. This is because of the high percentages of silt and clay size particles that affect the frost heaving properties of the tills as well as their suitability for construction. A till is considered fine

  6. Stratigraphy of the PB-1 well, Nopal I uranium deposit, Sierra Pena Blanca, Chihuahua, Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Dobson, P.; Fayek, M.; Goodell, P.; Ghezzehei, T.; Melchor, F.; Murrell, M.; Oliver, R.; Reyes-Cortes, I.A.; de la Garza, R.; Simmons, A.

    2008-08-01

    The Nopal I site in the Pena Blanca uranium district has a number of geologic and hydrologic similarities to the proposed high-level radioactive waste repository at Yucca Mountain, making it a useful analogue to evaluate process models for radionuclide transport. The PB-1 well was drilled in 2003 at the Nopal I uranium deposit as part of a DOE-sponsored natural analogue study to constrain processes affecting radionuclide transport. The well penetrates through the Tertiary volcanic section down to Cretaceous limestone and intersects the regional aquifer system. The well, drilled along the margin of the Nopal I ore body, was continuously cored to a depth of 250 m, thus providing an opportunity to document the local stratigraphy. Detailed observations of these units were afforded through petrographic description and rock-property measurements of the core, together with geophysical logs of the well. The uppermost unit encountered in the PB-1 well is the Nopal Formation, a densely welded, crystal-rich, rhyolitic ash-flow tuff. This cored section is highly altered and devitrified, with kaolinite, quartz, chlorite, and montmorillonite replacing feldspars and much of the groundmass. Breccia zones within the tuff contain fracture fillings of hematite, limonite, goethite, jarosite, and opal. A zone of intense clay alteration encountered in the depth interval 17.45-22.30 m was interpreted to represent the basal vitrophyre of this unit. Underlying the Nopal Formation is the Coloradas Formation, which consists of a welded lithic-rich rhyolitic ash-flow tuff. The cored section of this unit has undergone devitrification and oxidation, and has a similar alteration mineralogy to that observed in the Nopal tuff. A sharp contact between the Coloradas tuff and the underlying Pozos Formation was observed at a depth of 136.38 m. The Pozos Formation consists of poorly sorted conglomerate containing clasts of subangular to subrounded fragments of volcanic rocks, limestone, and chert

  7. Stratigraphy of the PB-1 well, Nopal I uranium deposit, Sierra Pena Blanca, Chihuahua, Mexico

    International Nuclear Information System (INIS)

    Dobson, P.; Fayek, M.; Goodell, P.; Ghezzehei, T.; Melchor, F.; Murrell, M.; Oliver, R.; Reyes-Cortes, I.A.; de la Garza, R.; Simmons, A.

    2008-01-01

    The Nopal I site in the Pena Blanca uranium district has a number of geologic and hydrologic similarities to the proposed high-level radioactive waste repository at Yucca Mountain, making it a useful analogue to evaluate process models for radionuclide transport. The PB-1 well was drilled in 2003 at the Nopal I uranium deposit as part of a DOE-sponsored natural analogue study to constrain processes affecting radionuclide transport. The well penetrates through the Tertiary volcanic section down to Cretaceous limestone and intersects the regional aquifer system. The well, drilled along the margin of the Nopal I ore body, was continuously cored to a depth of 250 m, thus providing an opportunity to document the local stratigraphy. Detailed observations of these units were afforded through petrographic description and rock-property measurements of the core, together with geophysical logs of the well. The uppermost unit encountered in the PB-1 well is the Nopal Formation, a densely welded, crystal-rich, rhyolitic ash-flow tuff. This cored section is highly altered and devitrified, with kaolinite, quartz, chlorite, and montmorillonite replacing feldspars and much of the groundmass. Breccia zones within the tuff contain fracture fillings of hematite, limonite, goethite, jarosite, and opal. A zone of intense clay alteration encountered in the depth interval 17.45-22.30 m was interpreted to represent the basal vitrophyre of this unit. Underlying the Nopal Formation is the Coloradas Formation, which consists of a welded lithic-rich rhyolitic ash-flow tuff. The cored section of this unit has undergone devitrification and oxidation, and has a similar alteration mineralogy to that observed in the Nopal tuff. A sharp contact between the Coloradas tuff and the underlying Pozos Formation was observed at a depth of 136.38 m. The Pozos Formation consists of poorly sorted conglomerate containing clasts of subangular to subrounded fragments of volcanic rocks, limestone, and chert

  8. Shaded Relief with Height as Color, Iturralde Structure, Bolivia

    Science.gov (United States)

    2002-01-01

    An 8-kilometer (5-mile) wide crater of possible impact origin is shown in this view of an isolated part of the Bolivian Amazon from the Shuttle Radar Topography Mission. The circular feature at the center-left of the image, known as the Iturralde Structure, is possibly the Earth's most recent 'big' impact event recording collision with a meteor or comet that might have occurred between 11,000 and 30,000 years ago.Although the structure was identified on satellite photographs in the mid-1980s, its location is so remote that it has only been visited by scientific investigators twice, most recently by a team from NASA's Goddard Space Flight Center in September 2002. Lying in an area of very low relief, the landform is a quasi-circular closed depression only about 20 meters (66 feet) in depth, with sharply defined sub-angular 'rim' materials. It resembles a 'cookie cutter' in that its appearance 'cuts' the heavily vegetated soft-sediments and pampas of this part of Bolivia. The SRTM data have provided investigators with the first topographic map of the site and will allow studies of its three-dimensional structure crucial to determining whether it actually is of impact origin.Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction. North-facing slopes appear bright and south-facing slopes appear dark. Color coding is directly related to topographic height, with brown and green at the lower elevations, rising through yellow and brown to white at the highest elevations.Elevation data used in this image was acquired by the Shuttle Radar Topography Mission aboard Space Shuttle Endeavour, launched on Feb. 11, 2000. The mission used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on Endeavour in 1994. The Shuttle Radar Topography Mission was

  9. Geochemical radioactive investigation of beach sands and stream sediments, using heavy minerals, trace elements and radon measurements, (Qerdaha sheet of the Syrian coast)

    International Nuclear Information System (INIS)

    Jubeli, Y.; Kattaa, B.; Al-Hilal, M.

    2000-05-01

    Reconnaissance geochemical radiometric survey of stream sediments resulting from the weathering of outcropped rocks in and around the study area was performed. This survey included heavy mineral sampling, trace and radioelements and radon measurements to evaluate the radioactivity of the source rocks and to understand the nature and distribution of the heavy minerals and trace elements in the study area. Several techniques were used to achieve these objectives. The results of heavy mineral geochemical survey show that the abundant minerals are iron oxides (magnetite, hematite, goehtite and limonite) pyroxene and olivine; less abundant minerals are apatite, ilmenite, garnet, barite, siderite and gloconite, while rare minerals are zircon and rutile. Amphibole is reported as an abundant mineral in sand dunes and is less abundant in samples located in the northern part of the study area. The amphibole seems to be derived from the ophiolitic complex north of the study area. Grain size analysis of heavy minerals revealed that the concentration of economic minerals such as zircon rutile and ilmenite increases with the decrease of the grain size. The microscopic study showed fragments and fossils of foraminifere mostly impregnated with heavy metals such as iron and manganese resulting from diagenetic metasomatism and replacement processes of. Fish teeth (< 2 mm) and oolite of iron were also noticed in most of the samples. The morphology of heavy mineral grains shows that most of the grains are angular to subangular suggesting that they were transported for short distance from their source rocks. Normally, phosphate pellets, gloconite and iron ooids are not considered since their original morphological features show clear roundness that attributed to their sedimentological origin, not to transportation factor. The source rock of most of the heavy mineral assemblage is the basalt. Apatite and gloconite are derived from the phosphorite and phosphatized limestone encountered

  10. Radon, radionuclides and the Cretaceous Folkestone Sands - gamma spectroscopy and geochemical analysis of silver sands and associated deposits in the SE of England.

    Science.gov (United States)

    Gillmore, Gavin; Al-Rafai, Yousef; Flowers, Alan

    2017-04-01

    cement holding the grains together (typical porosity being around 30%). Microscope analysis shows that this material contains mostly angular to sub-angular quartz grains, some with undulose extinction under cross-polarised light. This suggests a metamorphic origin for the quartz. There are also some relatively rare rock fragments present. These silver sands are a mixture of fine to medium grain sizes (0.10 to 0.5 mm) with small proportions of finer and coarser grades and are in the order of 30 - 36 metres thick at Reigate. These beds show lateral and vertical variability in their grain size, mineralogy and geochemical make up such as iron oxide content and are heavily faulted in places. In view of these radon results, in order to determine whether these levels are supported or unsupported, samples were collected and subjected to laboratory-based Gamma spectrometry. This indicated the presence of U235 (186keV) and Pb212 (238keV) in sands from these caves. We will shortly be in a position to also report in-situ gamma spectrometry and ICPMS analysis of samples taken from these beds.

  11. Bottom-up and top-down triggers of diversification: A new look at the evolutionary ecology of scavenging amphipods in the deep sea

    Science.gov (United States)

    Havermans, Charlotte; Smetacek, Victor

    2018-05-01

    The initial, anthropocentric view of the deep ocean was that of a hostile environment inhabited by organisms rendered lethargic by constant high pressure, low temperature and sparse food supply, hence evolving slowly. This conceptual framework of a spatially and temporally homogeneous, connected, strongly bottom-up controlled habitat implied a strong constraint on, or poor incentive for, speciation. Hence, the discovery in the late 1960s of high species diversity of abyssal benthic invertebrates came as a surprise. Since then, the slow-motion view of deep-sea ecology and evolution has speeded up and diversified in the light of increasing evidence accumulating from in situ visual observations complemented by molecular and other tools. The emerging picture is that of a much livelier, highly diversified and more complex deep-sea fauna than previously assumed. In this review we examine the consequences of the incoming information for developing a broader view of evolutionary ecology in the deep sea, and for scavenging amphipods in particular. We revisit the food supply to the deep-sea floor and hypothesize that the dead bodies of animals, ranging from zooplankton to large fish are likely to be a more important source of food than their friable faeces. Camera observations of baited traps indicate that amphipod carrion-feeders arrive within hours at the bait which continues to draw new individuals for days to months later, presumably by scent trails in tidal currents. We explore the different stages of food acquisition upon which natural selection may have acted, from detection to ingestion, and discuss the possibility of a broader range of food acquisition strategies, including predation and specializations. Although currently neglected in deep-sea ecology, top-down factors are likely to play a more important role in the evolution of deep-sea organisms. Predation on amphipods at baits by bathyal and abyssal fishes, and large predatory crustaceans in the hadal zone, is

  12. Estudio para la propagación vegetativa in vitro de Anón amazónico (Rollinia mucosa (JACQ. BAILL

    Directory of Open Access Journals (Sweden)

    Claudia Patricia Marín Jaramillo

    2003-01-01

    Full Text Available Para lograr la producción de material vegetal de Anón amazónico Rollinia mucosa (Jacq. Baill, se buscó el establecimiento en condiciones in vitro de segmentos nodales de árboles adultos, para lo cual se aplicaron ensayos de desinfección y control de la oxidación. Aunque se logró el control de la contaminación no fue posible el establecimiento in vitro, debido a la perdida de viabilidad. Para facilitar el manejo de los problemas de contaminación durante la fase de establecimiento, se realizaron ensayos para la germinación de semillas en condiciones in vitro, pero no se logró la germinación de estas, razón por la cual se sembraron en tierra estéril. Las semillas germinaron entre los 35 y 50 días. Cuando las plántulas tuvieron dos meses de edad se tomaron explantes de hipocótilos y hojas, a los que se les realizaron ensayos de desinfección y control de oxidación. Fue posible el control de la contaminación en los explantes de hoja y de la oxidación en los de hipocótilo. Se evaluó el efecto de los reguladores de crecimiento ácido naftalenacético, ANA, bencilaminopurina, BAP, ácido diclorofenoxiacético, 2,4-D y thidiazuron, TDZ, sobre la inducción de morfogénesis en segmentos de hipocótilos, para las hojas se evalúo el efecto del BAP, del ácido 3-indol acético, AIA, y de la acción conjunta de estos dos reguladores de crecimiento. En las hojas se logró la inducción de rizogénesis, caulogénesis indirecta y producción de callo friable. En los hipocótilos fue posible la inducción de organogénesis directa, y la obtención de plántulas de aspecto norma.

  13. Callus induction of leaf explant Piper betle L. Var Nigra with combination of plant growth regulators indole-3-acetic acid (IAA), benzyl amino purin (BAP) and kinetin

    Science.gov (United States)

    Junairiah, Zuraidassanaaz, Nabilah Istighfari; Izdihar, Fairuz Nabil; Manuhara, Yosephine Sri Wulan

    2017-09-01

    The purpose of this research was to determine the combination of plant growth regulators IAA, BAP and kinetin towards callus induction and growth of leaf explants Piper betle L. VarNigra. Explants from leaf of Piper betle L. VarNigra was cultured on MS medium with 24 treatment combinations of plant growth regulators IAA and BAP and 24 treatment combinations of plant growth regulators IAA and kinetin with 0.0;0.5;1.0;1.5;2.0 mg/L concentration respectively, the observed variable were the length of time the formation of callus, callus morphology, fresh and dry weight of callus. The results of this research showed that the combination of growth regulators IAA with BAP and kinetin had effects on leaf growth of Piper betle L. VarNigra. During 8 weeks observation, it indicated that the combination of concentration IAA 0.5 mg/L and BAP 2.0 mg/L showed fastest callus formation at 8.5 days. Combination of concentration IAA 1.0 mg/L and BAP 1.5 mg/L showed the highest of fresh weight at 0.6596 grams, and the highest dry weight was obtained from the combination of concentration IAA 0.5 mg/L and BAP 0.5 mg/L at 0.0727 grams. Combination of concentration IAA 1.0 mg/L and kinetin 1.5 mg/L had the highest of fresh weight at 0.2972 grams and the highest dry weight at 0.1660 grams. Callus of Piper betle L. VarNigra had two textures, that were compact and friable, and also showed various kind of colors, like white, greenish white, yellowish white, tanned white, brown and black. Based on this research, that concentration IAA 1.0 mg/L and 1.5 mg/L kinetin was the best combination for induction of callus from leaf of Piper betle L. Var Nigra.

  14. Interrelating the breakage and composition of mined and drill core coal

    Science.gov (United States)

    Wilson, Terril Edward

    Particle size distribution of coal is important if the coal is to be beneficiated, or if a coal sales contract includes particle size specifications. An exploration bore core sample of coal ought to be reduced from its original cylindrical form to a particle size distribution and particle composition that reflects, insofar as possible, a process stream of raw coal it represents. Often, coal cores are reduced with a laboratory crushing machine, the product of which does not match the raw coal size distribution. This study proceeds from work in coal bore core reduction by Australian investigators. In this study, as differentiated from the Australian work, drop-shatter impact breakage followed by dry batch tumbling in steel cylinder rotated about its transverse axis are employed to characterize the core material in terms of first-order and zeroth-order breakage rate constants, which are indices of the propensity of the coal to degrade during excavation and handling. Initial drop-shatter and dry tumbling calibrations were done with synthetic cores composed of controlled low-strength concrete incorporating fly ash (as a partial substitute for Portland cement) in order to reduce material variables and conserve difficult-to-obtain coal cores. Cores of three different coalbeds--Illinois No. 6, Upper Freeport, and Pocahontas No. 5 were subjected to drop-shatter and dry batch tumbling tests to determine breakage response. First-order breakage, characterized by a first-order breakage index for each coal, occurred in the drop-shatter tests. First- and zeroth-order breakage occurred in dry batch tumbling; disappearance of coarse particles and creation of fine particles occurred in a systematic way that could be represented mathematically. Certain of the coal cores available for testing were dry and friable. Comparison of coal preparation plant feed with a crushed bore core and a bore core prepared by drop-shatter and tumbling (all from the same Illinois No.6 coal mining

  15. Alberca De Guadalupe Maar Crater, Zacapu Basin : A Rare Type of Volcano within the Michoacán-Guanajuato Volcanic Field, México

    Science.gov (United States)

    Kshirsagar, P. V.; Siebe, C.; Guilbaud, M. N.; Salinas, S.

    2014-12-01

    Phreato-magmatic vents (esp. maar craters) are rare in the ~40,000 Km2 Plio-Quaternary monogenetic Michoacán-Guanajuato Volcanic Field (MGVF) located in the central part of the Mexican Volcanic Belt. In contrast to >1000 scoria cones, only 2 dozen phreato-magmatic monogenetic vents (e.g. tuff cones, tuff rings, and maars) have been identified. About half of these form a cluster near Valle de Santiago in the Lerma river valley at the northern margin of the MGVF, while the others occur in a rather scattered fashion. Here we discuss the origin of Alberca de Guadalupe maar crater, one of the three phreato-magmatic vents (in addition to El Caracol and Alberca de Los Espinos) that occur within the boundaries of the inter-montane lacustrine Zacapu basin, a tectonic graben bound by an ENE-WSW normal fault system. The maar crater came into existence between 20,000 and 23,000 y BP, forming a 140 m deep hole in the otherwise planar surrounding ground of theearly Pleistocene lava flows of Cerro Pelón.The maar crater has a diameter of ~1 Km and bears a 9 m deep lake. Eruptive products include typical surge deposits that are best exposed around the rim and inner crater walls. They are poorly sorted (Mdø= -1.56 to -3.75, ø= 1.43 to 3.23), rich in accidental lithics (angular andesitic lava and ignimbrite clasts) constituting 51-88% of the deposit with few juveniles (basaltic andesite with phenocrysts of plagioclase, olivine, and pyroxene in a quenched glassy matrix; SiO2=54-58 wt. %). Dry surge units are friable and clast-supported, in contrast the wet surge units are fairly indurated and bear accretionary lapilli. Bedding is frequently distorted by ballistic impact-sag structures. The entire construct is disrupted by an E-W trending regional fault, downthrowing the northern part by ~30 m.The unusual formation of this maar crater in the semi-arid highlands of Zacapu was favored by the local hydrological and topographical conditions. Such conditions still prevail in several

  16. Mapping Variability in the Medusae Fossae Formation: Yardang Morphologies, Fluvial Reworking, and Crater Depth to Diameter Ratios

    Science.gov (United States)

    Khuller, A. R.; Kerber, L.

    2017-12-01

    during the history of the MFF. The preservation of fluvial activity, through inversion and negative relief as well as the `protection' provided by the layers of friable MFF deposits indicates that some of the most well-preserved stratigraphy could perhaps be accessed by future Martian surface exploration missions within the MFF.

  17. Fabrication of Chemically Doped, High Upper Critical Field Magnesium Diboride Superconducting Wires

    Energy Technology Data Exchange (ETDEWEB)

    Marzik, James, V.

    2005-10-13

    Controlled chemical doping of magnesium diboride (MgB2) has been shown to substantially improve its superconducting properties to the levels required for high field magnets, but the doping is difficult to accomplish through the usual route of solid state reaction and diffusion. Further, superconducting cables of MgB2 are difficult to fabricate because of the friable nature of the material. In this Phase I STTR project, doped and undoped boron fibers were made by chemical vapor deposition (CVD). Several >100m long batches of doped and undoped fiber were made by CVD codeposition of boron plus dopants. Bundles of these fibers infiltrated with liquid magnesium and subsequently converted to MgB2 to form Mg-MgB2 metal matrix composites. In a parallel path, doped boron nano-sized powder was produced by a plasma synthesis technique, reacted with magnesium to produce doped MgB2 superconducting ceramic bodies. The doped powder was also fabricated into superconducting wires several meters long. The doped boron fibers and powders made in this program were fabricated into fiber-metal composites and powder-metal composites by a liquid metal infiltration technique. The kinetics of the reaction between boron fiber and magnesium metal was investigated in fiber-metal composites. It was found that the presence of dopants had significantly slowed the reaction between magnesium and boron. The superconducting properties were measured for MgB2 fibers and MgB2 powders made by liquid metal infiltration. Properties of MgB2 products (Jc, Hc2) from Phase I are among the highest reported to date for MgB2 bulk superconductors. Chemically doped MgB2 superconducting magnets can perform at least as well as NbTi and NbSn3 in high magnetic fields and still offer an improvement over the latter two in terms of operating temperature. These characteristics make doped MgB2 an effective material for high magnetic field applications, such as magnetic confined fusion, and medical MRI devices. Developing

  18. GENERAL AND SPECIFIC COMBINING ABILITY OF INITIAL PARENTAL FORMS IN TOMATO FOR COMPLEX OF ECONOMICALLY VALUABLE TRAITS TO DEVELOP HYBRIDS F1 OF CHERRY AND COCKTAIL TYPES

    Directory of Open Access Journals (Sweden)

    R. K. Rechets

    2017-01-01

    Full Text Available Results of estimation of general and specific combining ability of male and female parental tomato forms were given for complex of traits. The estimation was carried out according to incomplete diallel crosses 15x15. Such varities   as   ‘Trapeza’,  Rosovaya  kapelka’,  ‘Seniorita’, ‘Ocharovanie’,  ‘Tigris’   ‘Vishnya  Zheltaya’  (Gavrish, ‘Denezhnoye Derevo’ (national breeding, and  lines: ‘46/06’,  ‘49/09’,  ‘295/09’,  ‘336/11’,  ‘354/11’,  ‘357/11’, ‘388/09’ (nor, ‘498’ (selection of TARI were used as intial breeding accessions, differing in bush type (determinate and indeterminate, duration of vegetative phase (ultraearly,  early, medium early, middle-ripening, fruit  shape (rounded, oval, fruit color (red, pink, black, orange, tiger and with the gene nor, fruit weight (10 g. and more, brush structure (dense, friable. As a results, ‘Trapeza’, ‘Vishnya Zheltaya’, ‘Ocharovaniye’, ‘Seniorita’, and lines: ‘295/10’, ‘49/09’,  ‘498’,  ‘357/11’,  ‘354/11’,  ‘388/09’  (nor were selected and recommended to be used in breeding program for development of heterotic hybrids with high fruit setting and generative bush type. The promising hybrids F1 with high constants of specific combining ability for a complex of economically valuable traits have been observed. Because of different lines and accessions were used in crossings, these hybrids varied in internode length of cluster type, classical or shorten; rounded or oval fruit shape; fruit  color, red (F1   combinations ‘354/11’ х ‘Seniorita’, ‘Trapeza’ х  ‘L.49/09’,  L.  ‘49/09’  х  L.354/11, pink (F1 combination ‘Rosovaya Kapelka’ х ‘L.354/11’, yellow (F1 combination ‘Ocharovaniye’ х  ‘Vishiya Zheltaya’, deep brown (F1 combination  ‘L.357/11’ х ‘L.354/11’.

  19. Conduit enlargement in an eogenetic karst aquifer

    Science.gov (United States)

    Moore, Paul J.; Martin, Jonathan B.; Screaton, Elizabeth J.; Neuhoff, Philip S.

    2010-11-01

    SummaryMost concepts of conduit development have focused on telogenetic karst aquifers, where low matrix permeability focuses flow and dissolution along joints, fractures, and bedding planes. However, conduits also exist in eogenetic karst aquifers, despite high matrix permeability which accounts for a significant component of flow. This study investigates dissolution within a 6-km long conduit system in the eogenetic Upper Floridan aquifer of north-central Florida that begins with a continuous source of allogenic recharge at the Santa Fe River Sink and discharges from a first-magnitude spring at the Santa Fe River Rise. Three sources of water to the conduit include the allogenic recharge, diffuse recharge through epikarst, and mineralized water upwelling from depth. Results of sampling and inverse modeling using PHREEQC suggest that dissolution within the conduit is episodic, occurring only during 30% of 16 sampling times between March 2003 and April 2007. During low flow conditions, carbonate saturated water flows from the matrix to the conduit, restricting contact between undersaturated allogenic water with the conduit wall. When gradients reverse during high flow conditions, undersaturated allogenic recharge enters the matrix. During these limited periods, estimates of dissolution within the conduit suggest wall retreat averages about 4 × 10 -6 m/day, in agreement with upper estimates of maximum wall retreat for telogenetic karst. Because dissolution is episodic, time-averaged dissolution rates in the sink-rise system results in a wall retreat rate of about 7 × 10 -7 m/day, which is at the lower end of wall retreat for telogenetic karst. Because of the high permeability matrix, conduits in eogenetic karst thus enlarge not just at the walls of fractures or pre-existing conduits such as those in telogenetic karst, but also may produce a friable halo surrounding the conduits that may be removed by additional mechanical processes. These observations stress the

  20. A preliminary evaluation of comminution and sampling strategies for radioactive cemented waste

    Energy Technology Data Exchange (ETDEWEB)

    Bilodeau, M.; Lastra, R.; Bouzoubaa, N. [Natural Resources Canada, Ottawa, ON (Canada); Chapman, M. [Atomic Energy of Canada Limited, Chalk River, ON (Canada)

    2011-07-01

    Lixiviation of Hg, U and Cs contaminants and micro-encapsulation of cemented radioactive waste (CRW) are the two main components of a CRW stabilization research project carried out at Natural Resources Canada in collaboration with Atomic Energy of Canada Limited. Unmolding CRW from the storage pail, its fragmentation into a size range suitable for both processes and the collection of a representative sample are three essential steps for providing optimal material conditions for the two studies. Separation of wires, metals and plastic incorporated into CRW samples is also required. A comminution and sampling strategy was developed to address all those needs. Dust emissions and other health and safety concerns were given full consideration. Surrogate cemented waste (SCW) was initially used for this comminution study where Cu was used as a substitute for U and Hg. SCW was characterized as a friable material through the measurement of the Bond work index of 7.7 kWh/t. A mineralogical investigation and the calibration of material heterogeneity parameters of the sampling error model showed that Cu, Hg and Cs are finely disseminated in the cement matrix. A sampling strategy was built from the model and successfully validated with radioactive waste. A larger than expected sampling error was observed with U due to the formation of large U solid phases, which were not observed with the Cu tracer. SCW samples were crushed and ground under different rock fragmentation mechanisms: compression (jaw and cone crushers, rod mill), impact (ball mill), attrition, high voltage disintegration and high pressure water (and liquid nitrogen) jetting. Cryogenic grinding was also tested with the attrition mill. Crushing and grinding technologies were assessed against criteria that were gathered from literature surveys, experiential know-how and discussion with the client and field experts. Water jetting and its liquid nitrogen variant were retained for pail cutting and waste unmolding while

  1. A preliminary evaluation of comminution and sampling strategies for radioactive cemented waste

    International Nuclear Information System (INIS)

    Bilodeau, M.; Lastra, R.; Bouzoubaa, N.; Chapman, M.

    2011-01-01

    Lixiviation of Hg, U and Cs contaminants and micro-encapsulation of cemented radioactive waste (CRW) are the two main components of a CRW stabilization research project carried out at Natural Resources Canada in collaboration with Atomic Energy of Canada Limited. Unmolding CRW from the storage pail, its fragmentation into a size range suitable for both processes and the collection of a representative sample are three essential steps for providing optimal material conditions for the two studies. Separation of wires, metals and plastic incorporated into CRW samples is also required. A comminution and sampling strategy was developed to address all those needs. Dust emissions and other health and safety concerns were given full consideration. Surrogate cemented waste (SCW) was initially used for this comminution study where Cu was used as a substitute for U and Hg. SCW was characterized as a friable material through the measurement of the Bond work index of 7.7 kWh/t. A mineralogical investigation and the calibration of material heterogeneity parameters of the sampling error model showed that Cu, Hg and Cs are finely disseminated in the cement matrix. A sampling strategy was built from the model and successfully validated with radioactive waste. A larger than expected sampling error was observed with U due to the formation of large U solid phases, which were not observed with the Cu tracer. SCW samples were crushed and ground under different rock fragmentation mechanisms: compression (jaw and cone crushers, rod mill), impact (ball mill), attrition, high voltage disintegration and high pressure water (and liquid nitrogen) jetting. Cryogenic grinding was also tested with the attrition mill. Crushing and grinding technologies were assessed against criteria that were gathered from literature surveys, experiential know-how and discussion with the client and field experts. Water jetting and its liquid nitrogen variant were retained for pail cutting and waste unmolding while

  2. Examination of Surface Residuals Obtained During Re-Lubrication of the International Space Station (ISS) Solar Alpha Rotary Joint (SARJ)

    Science.gov (United States)

    Martinez, J. E.; Golden, J. L.

    2012-01-01

    shows an example of a region of concentrated wear debris. Although some MoS2 is observed, most of the contaminant in this location is nitrided 15-5PH steel, as verified by the associated chemical analysis. High oxygen content was also observed which, when associated with the apparent friable nature of the steel material, suggests that this contaminant could be quite old, perhaps even associated with the mechanism s original manufacture and acceptance testing. Additional microscopic

  3. Orthopaedic management of haemophilia arthropathy of the ankle.

    Science.gov (United States)

    Pasta, G; Forsyth, A; Merchan, C R; Mortazavi, S M J; Silva, M; Mulder, K; Mancuso, E; Perfetto, O; Heim, M; Caviglia, H; Solimeno, L

    2008-07-01

    Joint bleeding, or haemarthrosis, is the most common type of bleeding episode experienced by individuals with haemophilia A and B. This leads to changes within the joints, including synovial proliferation, which results in further bleeding and chronic synovitis. Blood in the joint can also directly damage the cartilage, and with repeated bleeding, there is progressive destruction of both cartilage and bone. The end result is known as haemophilic arthropathy. The joints most commonly affected are the knees, elbows and ankles, although any synovial joint may be involved. In the ankle, both the tibiotalar and subtalar joints may be affected and joint bleeding and arthropathy can lead to a number of deformities. Haemophilic arthropathy can be prevented through regular factor replacement prophylaxis and implementing physiotherapy. However, when necessary, there are multiple surgical and non-surgical options available. In early ankle arthropathy with absent or minimal joint changes, both radioisotopic and chemical synoviorthesis can be used to reduce the hypertrophied synovium. These procedures can decrease the frequency of bleeding episodes, minimizing the risk of articular cartilage damage. Achilles tendon lengthening can be performed, in isolation or in combination with other surgical measures, to correct Achilles tendon contractures. Both arthroscopic and open synovectomies are available as a means to remove the friable villous layer of the synovium and are often indicated when bleeding episodes cannot be properly controlled by factor replacement therapy or synoviorthesis. In the later stages of ankle arthropathy, other surgical options may be considered. Debridement may be indicated when there are loose pieces of cartilage or anterior osteophytes, and can help to improve the joint function, even in the presence of articular cartilage damage. Supramalleolar tibial osteotomy may be indicated in patients with a valgus deformity of the hindfoot without degenerative

  4. Preliminary mineralogical and paleoenvironmental study of the diatomites from Adamclisi, South Dobrogea, Romania

    Science.gov (United States)

    Dumitras, Delia-Georgeta; Sebe-Radoi, Oana-Gabriela; Marincea, Stefan; Costea, Constantin

    2017-04-01

    Diatomite samples taken from the Urluia - Adamclisi localities, South Dobrogea region (Romania) have been studied by X-ray fluorescence, wet-chemical analysis, scanning electron microscopy (SEM), FTIR and X-ray powder diffraction. The diatomaceous earth from Adamclisi occurs as beds and lenses in alternance with bentonitic clays and limestones. The diatomite levels are chalk-like, soft, friable, earthy, very fine-grained, and have a white - yellow color. The mineralogy of all but one sample is characterized by the presence of quartz, amorphous silica, feldspars and clay minerals. Based on the broad hump registered between 15 and 20° 2 theta on XRD patterns and on the characters and intensities of the bands centered around 3350 and 1630 cm-1 in the FTIR spectra, the amorphous silica from the diagenesis-affected diatom frustules was identified as opal-A. The associated mineral species are quartz (up to 5 wt.%), opal-Ct (up to 15 wt%), clay minerals (up to 60 wt.%), and minor feldspar (up to 20 wt.%). The micro-paleontological study shows that benthic pennate diatoms prevail (more than 60%), with a low rate of species diversity. Large chain-forming centric diatoms also occur together with other microfossils (dinoflagellates, phytolites, sponge spicules, different types of fish teeth) assemblages common for the Sarmatian (middle Miocene) marine deposits of Eastern Paratethys. The diatomaceous formation afforded exceptional fossilization. The diatom assemblages characterize a shallow marine basin environment, with littoral or freshwater contributions. Both at the basis and on the top of the profile, the marine diatoms prevail. At the basis of profile, the marine species (e.g., Actinocyclus ehrenbergii, Amphora crassa, Amphora crassa-punctata, Caloneis liber, Camylodiscus kutzingii, Grammatophora stricta, etc.) form up to 80 % of the rock volume, being associated with marine-brackish species such as Achnanthes brevipes and Cocconeis scutelum (up to 25 %) and with

  5. Structural features of the San Andreas fault at Tejon Pass, California

    Science.gov (United States)

    Dewers, T. A.; Reches, Z.; Brune, J. N.

    2002-12-01

    We mapped a 2 km belt along the San Andreas fault (SAF) in the Tejon Pass area where road cuts provide fresh exposures of the fault zone and surrounding rocks. Our 1:2,000 structural mapping is focused on analysis of faulting processes and is complementary to regional mapping at 1:12,000 scale by Ramirez (M.Sc., UC Santa Barbara, 1984). The dominant rock units are the Hungry Valley Formation of Pliocene age (clastic sediments) exposed south of the SAF, and the Tejon Lookout granite (Cretaceous) and Neenach Volcanic Formation exposed north of it. Ramirez (1983) deduced ~220 km of post-Miocene lateral slip. The local trend of the SAF is about N60W and it includes at least three main, subparallel segments that form a 200 m wide zone. The traces of the segments are quasi-linear, discontinuous, and they are stepped with respect to each other, forming at least five small pull-aparts and sag ponds in the mapping area. The three segments were not active semi-contemporaneously and the southern segment is apparently the oldest. The largest pull-apart, 60-70 m wide, displays young (Quaternary?) silt and shale layers. We found two rock bodies that are suspected as fault-rocks. One is a 1-2 m thick sheet-like body that separates the Tejon Lookout granite from young (Recent?) clastic rocks. In the field, it appears as a gouge zone composed of poorly cemented, dark clay size grains; however, the microstructure of this rock does not reveal clear shear features. The second body is the 80-120 m wide zone of Tejon Lookout granite that extends for less than 1 km along the SAF in the mapped area. It is characterized by three structural features: (1) pulverization into friable, granular material by multitude of grain-crossing fractures; (2) abundance of dip-slip small faults that are gently dipping toward and away from the SAF; and (3) striking lack of evidence for shear parallel to the SAF. The relationships between these features and the large right-lateral shear along the SAF are

  6. Erosion and Sedimentation from the Bagley Fire, Eastern Klamath Mountains, Northern CA

    Science.gov (United States)

    De La Fuente, J. A.; Bachmann, S.; Mai, C.; Mikulovsky, R.; Mondry, Z. J.; Rust, B.; Young, D.

    2014-12-01

    The Bagley Fire burned about 19,000 hectares on the Shasta-Trinity National Forest in the late summer of 2012, with soil burn severities of 11% high, 19% moderate and 48% low. Two strong storms in November and December followed the fire. The first storm had a recurrence interval of about 2 years, and generated runoff with a return interval of 10-25 years, causing many road stream crossing failures in parts of the fire. The second storm had a recurrence interval of 25-50 years, and initiated more severe erosion throughout the fire area. Erosional processes were dominated by sheet, rill and gully erosion, and landslides were uncommon. A model predicted high potential for debris flows, but few were documented, and though most stream channels exhibited fresh scour and deposition, residual deposits lacked boulder levees or other evidence of debris flow. Rather, deposits were stratified and friable, suggesting a sediment laden flood flow rather than debris flow origin. The resulting sediment was rich in gravel and finer particles, and poor in larger rock. Soil loss was estimated at 0.5-5.6 cm on most hillslopes. A high resolution DEM (LiDAR) was used to measure gullies, small landslides, and stream scour, and also to estimate sedimentation in Squaw Creek, and Shasta Lake. A soil erosion model was used to estimate surface erosion. Total erosion in the Squaw Creek watershed was estimated at 2.24 million metric tons, which equates to 260 metric tons/hectare. Of this, about 0.89 million metric tons were delivered to the stream system (103 metric tons/hectare). Nearly half of this sediment, 0.41 million metric tons, was temporarily stored in the Squaw Creek channel, and around 0.33 million metric tons of fine sediment were carried into Shasta Lake. Squaw Creek also delivered about 0.17 million metric tons of sand, gravel and cobbles to the lake. This estimate is very tenuous, and was made by measuring the volume of a delta in Shasta Lake from a tributary to Squaw Creek and

  7. CONCEPTUAL DESIGN ASSESSMENT FOR THE CO-FIRING OF BIO-REFINERY SUPPLIED LIGNIN PROJECT

    International Nuclear Information System (INIS)

    Ted Berglund; Jeffrey T. Ranney; Carol L. Babb; Jacqueline G. Broder

    2002-01-01

    The major aspects of this project are proceeding toward completion. Prior to this quarter, design criteria, tentative site selection, facility layout, and preliminary facility cost estimates were completed and issued. Processing of bio-solids was completed, providing material for the pilot operations. Pilot facility hydrolysis production has been completed to produce lignin for co-fire testing and the lignin fuel was washed and dewatered. Both the lignin and bio-solids fuel materials for co-fire testing were sent to the co-fire facility (EERC) for evaluation and co-firing. EERC has received coal typical of the fuel to the TVA-Colbert boilers. This material was used at EERC as baseline material and for mixing with the bio-fuel for combustion testing. All the combustion and fuel handling tests at EERC have been completed. During fuel preparation EERC reported no difficulties in fuel blending and handling. Preliminary co-fire test results indicate that the blending of lignin and bio-solids with the Colbert coal blend generally reduces NO(sub x) emissions, increases the reactivity of the coal, and increases the ash deposition rate on superheater surfaces. Deposits produced from the fuel blends, however, are more friable and hence easier to remove from tube surfaces relative to those produced from the baseline Colbert coal blend. The final co-fire testing report is being prepared at EERC and will be completed by the end of the second quarter of 2002. The TVA-Colbert facility has neared completion of the task to evaluate co-location of the Masada facility on the operation of the power generation facility. The TVA-Colbert fossil plant is fully capable of providing a reliable steam supply. The preferred steam supply connection points and steam pipeline routing have been identified. The environmental review of the pipeline routing has been completed and no major impacts have been identified. Detailed assessment of steam export impacts on the Colbert boiler system have been

  8. Fabrication of Chemically Doped, High Upper Critical Field Magnesium Diboride Superconducting Wires

    International Nuclear Information System (INIS)

    Marzik, James V.

    2005-01-01

    Controlled chemical doping of magnesium diboride (MgB2) has been shown to substantially improve its superconducting properties to the levels required for high field magnets, but the doping is difficult to accomplish through the usual route of solid state reaction and diffusion. Further, superconducting cables of MgB2 are difficult to fabricate because of the friable nature of the material. In this Phase I STTR project, doped and undoped boron fibers were made by chemical vapor deposition (CVD). Several >100m long batches of doped and undoped fiber were made by CVD codeposition of boron plus dopants. Bundles of these fibers infiltrated with liquid magnesium and subsequently converted to MgB2 to form Mg-MgB2 metal matrix composites. In a parallel path, doped boron nano-sized powder was produced by a plasma synthesis technique, reacted with magnesium to produce doped MgB2 superconducting ceramic bodies. The doped powder was also fabricated into superconducting wires several meters long. The doped boron fibers and powders made in this program were fabricated into fiber-metal composites and powder-metal composites by a liquid metal infiltration technique. The kinetics of the reaction between boron fiber and magnesium metal was investigated in fiber-metal composites. It was found that the presence of dopants had significantly slowed the reaction between magnesium and boron. The superconducting properties were measured for MgB2 fibers and MgB2 powders made by liquid metal infiltration. Properties of MgB2 products (Jc, Hc2) from Phase I are among the highest reported to date for MgB2 bulk superconductors. Chemically doped MgB2 superconducting magnets can perform at least as well as NbTi and NbSn3 in high magnetic fields and still offer an improvement over the latter two in terms of operating temperature. These characteristics make doped MgB2 an effective material for high magnetic field applications, such as magnetic confined fusion, and medical MRI devices. Developing

  9. Influence of hydrogen on optical destruction of the irradiated quartz glass

    International Nuclear Information System (INIS)

    Bedilov, M.R.; Beysembayeva, Kh.B.; Sabitov, M.S.

    2002-01-01

    maintained lamps capsules IFF-500 and IFF-8000 showed, that, despite of the different-, contents of hydrogen impurity in them, before irradiation it is ∼5·10 10 W/cm 2 . However, after an irradiation, is especial in reactors, the significant difference is found. It is caused by the greater probability of production of structural defects in a case of reactors irradiation. Most strongly it is shown at the capsules containing increased concentration of hydrogen, that is caused by more effective production in them of structural defects from behind friable structure of the given quartz glass

  10. Study on coating layer of ceramic materials for SFR fuel slugs

    International Nuclear Information System (INIS)

    Song, Hoon; Kim, Jonghwan; Kim, Kihwan; Ko, Youngmo; Woo, Yoonmyung; Lee, Chanbock

    2013-01-01

    The plasma-sprayed coating can provide the crucible with a denser, more durable, coating layer, compared with the more friable coating layer formed by slurry-coating. Plasma-sprayed coatings are consolidated by mechanical interlocking of the molten particles impacting on the substrate and are dense by the heat applied by the plasma. The objective of this study is to develop a coating method and material for crucibles to prevent material interactions with the U-Zr/U-TRU-Zr fuels. Reducing these interactions will result in a fuel loss reduction. According to coating and U-Zr interaction results preformed in previous experience, Y 2 O 3 , TiC, and TaC coating materials were selected as promising coating materials Various combinations of coating conditions such as; coating thickness, double multi-layer coating methods were investigated to find the bonding effect on the substrate in pursuit of more effective ways to withstand the thermal stresses. To develop a coating method and material for crucibles to prevent m