Structural integrity analysis of the 224U elevator mothballing

Energy Technology Data Exchange (ETDEWEB)

Boehnke, W.M.

1994-11-18

As part of the preparation of Building 224U for turnover to Decontamination and Decommissioning, it is necessary to place the elevator in a mothballed condition so that it can be reactivated for use after 10 to 25 years. This mothballing is going to be accomplished by landing the counterweight on wooden timbers and suspending the elevator cab with wire rope or chain slings. This will take the load off the cables and make it relatively easy to reactive. The objective of this Supporting Document is to verify the structural integrity of all of the load bearing components involved in mothballing the 224U Building elevator. Building 224U is part of the UO{sub 3} Plant where uranyl nitrates from the PUREX Plant was converted to UO{sub 3} powder.

The Effect of Elevated Temperature on Concrete Materials and Structures - a Literature Review.

Energy Technology Data Exchange (ETDEWEB)

Naus, Dan J [ORNL

2006-03-01

The objective of this limited study was to provide an overview of the effects of elevated temperature on the behavior of concrete materials and structures. In meeting this objective the effects of elevated temperatures on the properties of ordinary Portland cement concrete constituent materials and concretes are summarized. The effects of elevated temperature on high-strength concrete materials are noted and their performance compared to normal strength concretes. A review of concrete materials for elevated-temperature service is presented. Nuclear power plant and general civil engineering design codes are described. Design considerations and analytical techniques for evaluating the response of reinforced concrete structures to elevated-temperature conditions are presented. Pertinent studies in which reinforced concrete structural elements were subjected to elevated temperatures are described.

The Effect of Elevated Temperature on Concrete Materials and Structures - a Literature Review

International Nuclear Information System (INIS)

Naus, Dan J.

2006-01-01

The objective of this limited study was to provide an overview of the effects of elevated temperature on the behavior of concrete materials and structures. In meeting this objective the effects of elevated temperatures on the properties of ordinary Portland cement concrete constituent materials and concretes are summarized. The effects of elevated temperature on high-strength concrete materials are noted and their performance compared to normal strength concretes. A review of concrete materials for elevated-temperature service is presented. Nuclear power plant and general civil engineering design codes are described. Design considerations and analytical techniques for evaluating the response of reinforced concrete structures to elevated-temperature conditions are presented. Pertinent studies in which reinforced concrete structural elements were subjected to elevated temperatures are described.

Influence of a Cyclic Events Configuration on a Elevated Temperature Structural Integrity

International Nuclear Information System (INIS)

Park, Chang-Gyu; Koo, Gyeong-Hoi; Lee, Jae-Han

2008-01-01

A nuclear power plant generally undergoes the various types of operating events for a plant life time. The cyclic events for a life time may bring about a structural failure such as fatigue damage. The structures of the LMR(Liquid Metal Reactor) operated in a elevated temperature environment are seriously affected by a thermal deformation and strain. Therefore, the thermal transient condition is a key factor for ensuring the structural integrity for the LMR reactor structures. Since it is not easy to consider the entire operating events at the preliminary or conceptual design stage, the LMR structural integrity is evaluated with representative duty cycle events. In this study, the influence of the elevated temperature structural integrity evaluation per the combination and sequence of the duty cycle events is investigated

STRUCTURE LINE DETECTION FROM LIDAR POINT CLOUDS USING TOPOLOGICAL ELEVATION ANALYSIS

Directory of Open Access Journals (Sweden)

C. Y. Lo

2012-07-01

Full Text Available Airborne LIDAR point clouds, which have considerable points on object surfaces, are essential to building modeling. In the last two decades, studies have developed different approaches to identify structure lines using two main approaches, data-driven and modeldriven. These studies have shown that automatic modeling processes depend on certain considerations, such as used thresholds, initial value, designed formulas, and predefined cues. Following the development of laser scanning systems, scanning rates have increased and can provide point clouds with higher point density. Therefore, this study proposes using topological elevation analysis (TEA to detect structure lines instead of threshold-dependent concepts and predefined constraints. This analysis contains two parts: data pre-processing and structure line detection. To preserve the original elevation information, a pseudo-grid for generating digital surface models is produced during the first part. The highest point in each grid is set as the elevation value, and its original threedimensional position is preserved. In the second part, using TEA, the structure lines are identified based on the topology of local elevation changes in two directions. Because structure lines can contain certain geometric properties, their locations have small relieves in the radial direction and steep elevation changes in the circular direction. Following the proposed approach, TEA can be used to determine 3D line information without selecting thresholds. For validation, the TEA results are compared with those of the region growing approach. The results indicate that the proposed method can produce structure lines using dense point clouds.

Numerical modelling of ground vibration caused by elevated high-speed railway lines considering structure-soil-structure interaction

DEFF Research Database (Denmark)

Bucinskas, Paulius; Andersen, Lars Vabbersgaard; Persson, Kent

2016-01-01

Construction of high speed railway lines has been an increasing trend in recent years. Countries like Denmark and Sweden plan to expand and upgrade their railways to accommodate high-speed traffic. To benefit from the full potential of the reduced commuting times, these lines must pass through...... densely populated urban areas with the collateral effect of increased noise and vibrations levels. This paper aims to quantify the vibrations levels in the area surrounding an elevated railway line built as a multi-span bridge structure. The proposed model employs finite-element analysis to model......-space. The paper analyses the effects of structure-soil-structure interaction on the dynamic behaviour of the surrounding soil surface. The effects of different soil stratification and material properties as well as different train speeds are assessed. Finally, the drawbacks of simplifying the numerical model...

Competition and habitat filtering jointly explain phylogenetic structure of soil bacterial communities across elevational gradients.

Science.gov (United States)

Zhang, Qian; Goberna, Marta; Liu, Yuguo; Cui, Ming; Yang, Haishui; Sun, Qixiang; Insam, Heribert; Zhou, Jinxing

2018-04-24

The importance of assembly processes in shaping biological communities is poorly understood, especially for microbes. Here we report on the forces that structure soil bacterial communities along a 2000 m elevational gradient. We characterized the relative importance of habitat filtering and competition on phylogenetic structure and turnover in bacterial communities. Bacterial communities exhibited a phylogenetically clustered pattern and were more clustered with increasing elevation. Biotic factors (i.e. relative abundance of dominant bacterial lineages) appeared to be most important to the degree of clustering, evidencing the role of the competitive ability of entire clades in shaping the communities. Phylogenetic turnover showed the greatest correlation to elevation. After controlling for elevation, biotic factors showed greater correlation to phylogenetic turnover than all the habitat variables (i.e. climate, soil and vegetation). Structural equation modelling also identified that elevation and soil organic matter exerted indirect effects on phylogenetic diversity and turnover by determining the dominance of microbial competitors. Our results suggest that competition among bacterial taxa induced by soil carbon contributes to the phylogenetic pattern across elevational gradient in the Tibetan Plateau. This highlights the importance of considering not only abiotic filtering but also biotic interactions in soil bacterial communities across stressful elevational gradients. This article is protected by copyright. All rights reserved. © 2018 Society for Applied Microbiology and John Wiley & Sons Ltd.

Phylogenetic structure of arbuscular mycorrhizal fungal communities along an elevation gradient.

Science.gov (United States)

Egan, Cameron P; Callaway, Ragan M; Hart, Miranda M; Pither, Jason; Klironomos, John

2017-04-01

Despite the importance of arbuscular mycorrhizal (AM) fungi within terrestrial ecosystems, we know little about how natural AM fungal communities are structured. To date, the majority of studies examining AM fungal community diversity have focused on single habitats with similar environmental conditions, with relatively few studies having assessed the diversity of AM fungi over large-scale environmental gradients. In this study, we characterized AM fungal communities in the soil along a high-elevation gradient in the North American Rocky Mountains. We focused on phylogenetic patterns of AM fungal communities to gain insight into how AM fungal communities are naturally assembled. We found that alpine AM fungal communities had lower phylogenetic diversity relative to lower elevation communities, as well as being more heterogeneous in composition than either treeline or subalpine communities. AM fungal communities were phylogenetically clustered at all elevations sampled, suggesting that environmental filtering, either selection by host plants or fungal niches, is the primary ecological process structuring communities along the gradient.

Stress state of thin – walled member of the structure with operation damages under nonuniform loading

Directory of Open Access Journals (Sweden)

В.В. Астанін

2004-01-01

Full Text Available  The publication is dedicated to determining of stress state in particular the stress concentration factors for thin – walled members of the structures subject to nonuniform tension. A structure member has obtained the operation damage generation by corrosion and other causes.

Structure of radicals produced by γ radiolysis. Part 4. Adamantane matrices doped with various 5-membered heterocyclic molecules

International Nuclear Information System (INIS)

Winters, D.L.; Ling, A.C.

1976-01-01

The effects of γ-radiolysis at room temperature on adamantane and adamantane-d 16 matrices doped with 5-membered heterocyclic molecules has been examined by X-band electron spin resonance (esr) spectrometry. Radical structures formed from heterocyclic solute molecules are discussed and tentative assignments made. Discussion of possible radical structures derived from selected heterocyclic compounds is included, but unambiguous assignmens of structure cannot be made for these compounds from the esr data obtained. It was noted that perdeuterated adamantane matrices provided superior resolution for esr spectra derived from radicals with a delocalized spin center such as allyl or allenyl species. (author)

Structure and elevator mechanism of the Na+-citrate transporter CitS.

Science.gov (United States)

Lolkema, Juke S; Slotboom, Dirk Jan

2017-08-01

The recently determined crystal structure of the bacterial Na + -citrate symporter CitS provides unexpected structural and mechanistic insights. The protein has a fold that has not been seen in other proteins, but the oligomeric state, domain organization and proposed transport mechanism strongly resemble those of the sodium-dicarboxylate symporter vcINDY, and the putative exporters YdaH and MtrF, thus hinting at convergence in structure and function. CitS and the related proteins are predicted to translocate their substrates by an elevator-like mechanism, in which a compact transport domain slides up and down through the membrane while the dimerization domain is stably anchored. Here we review the large body of available biochemical data on CitS in the light of the new crystal structure. We show that the biochemical data are fully consistent with the proposed elevator mechanism, but also demonstrate that the current structural data cannot explain how strict coupling of citrate and Na + transport is achieved. We propose a testable model for the coupling mechanism. Copyright © 2016 Elsevier Ltd. All rights reserved.

Torsional Restraint Problem of Steel Cold-Formed Beams Restrained By Planar Members

Science.gov (United States)

Balázs, Ivan; Melcher, Jindřich; Pešek, Ondřej

2017-10-01

The effect of continuous or discrete lateral and torsional restraints of metal thinwalled members along their spans can positively influence their buckling resistance and thus contribute to more economical structural design. The prevention of displacement and rotation of the cross-section results in stabilization of the member. The restraints can practically be provided e.g. by planar members of cladding supported by metal members (purlins, girts). The rate of stabilization of a member can be quantified using values of shear and rotational stiffness provided by the adjacent planar members. While the lateral restraint effected by certain shear stiffness can be often considered as sufficient, the complete torsional restraint can be safely considered in some practical cases only. Otherwise the values of the appropriate rotational stiffness provided by adjacent planar members may not be satisfactory to ensure full torsional restraint and only incomplete restraint is available. Its verification should be performed using theoretical and experimental analyses. The paper focuses on problem of steel thin-walled coldformed beams stabilized by planar members and investigates the effect of the magnitude of the rotational stiffness provided by the planar members on the resistance of the steel members. Cold-formed steel beams supporting planar members of cladding are considered. Full lateral restraint and incomplete torsional restraint are assumed. Numerical analyses performed using a finite element method software indicate considerable influence of the torsional restraint on the buckling resistance of a steel thin-walled member. Utilization of the torsional restraint in the frame of sizing of a stabilized beam can result in more efficient structural design. The paper quantifies this effect for some selected cases and summarizes results of numerical analysis.

Nonlinear load-displacement analysis of structures having members ...

African Journals Online (AJOL)

Solid or hollow reclan~lar and circular crosssection members are most extensively used in medium and small size steel structures. Such crosssections are non-warping cross-section. They are extensively used because of their strength and the ease to assemble. The governing differential equations and the corresponding ...

Structural analysis for elevated temperature design of the LMFBR

International Nuclear Information System (INIS)

Griffin, D.S.

1976-02-01

In the structural design of LMFBR components for elevated temperature service it is necessary to take account of the time-dependent, creep behavior of materials. The accommodation of creep to assure design reliability has required (1) development of new design limits and criteria, (2) development of more detailed representations of material behavior, and (3) application of the most advanced analysis techniques. These developments are summarized and examples are given to illustrate the current state of technology in elevated temperature design

Some Fundamental Aspects of Mechanics of Nano composite Materials and Structural Members

International Nuclear Information System (INIS)

Guz, A.N.; Rushchitsky, J.J.

2013-01-01

This paper is devoted to formulation and analysis of fundamental aspects of mechanics of nano composite materials and structural members. These aspects most likely do not exhaust all of the possible fundamental characteristics of mechanics of nano composite materials and structural members, but, nevertheless, they permit to form the skeleton of direction of mechanics in hand. The proposed nine aspects are described and commented briefly.

Evaluation of Reinforced Concrete Structural Members under Uniform Loads Using Truss Model

Directory of Open Access Journals (Sweden)

Houshang Dabbagh

2016-03-01

Full Text Available Truss model is an analytical approach to predict the strength of reinforced concrete members with geometric or statical discontinuous regions. This study investigates the use of truss model to predict the structural behavior of reinforced concrete members with discontinuity areas under monotonic loading. The estimated failure load and its corresponding deformation are the main objective of this research. Twenty and three samples including short shear walls, short columns and deep beams tested by other researchers throughout the literature have been selected. Then their truss models as well as their three dimensional finite element models are analyzed using ABAQUS software. The comparison of experimental and analytical results shows fair correlation between them. Also, the structural response of samples estimated by truss model analysis is fairly acceptable.

Thermodynamic and structural characteristics of cement minerals at elevated temperature

International Nuclear Information System (INIS)

Bruton, C.J.; Meike, A.; Viani, B.E.; Martin, S.; Phillips, B.L.

1994-05-01

We have instituted an experimental and including program designed to elucidate the structural and thermodynamic response of cement minerals to elevated temperature. Components of the program involve: (a) synthesis of hydrated Ca-silicates; (b) structural analysis of cement phases induced by heating and dehydration/rehydration; (c) mechanistic and thermodynamic descriptions of the hydration/dehydration behavior of hydrated Ca-silicates as a function of temperature, pressure and relative humidity; (d) study of naturally occurring hydrated Ca-silicates; and (e) measurements of thermodynamic data for hydrated Ca-silicates

Structural variations in aromatic 2π-electron three-membered rings ...

Indian Academy of Sciences (India)

Abstract. Structural variations of different 2π-aromatic three-membered ring systems of main group ele- ments, especially group 14 and 13 elements as compared to the classical description of cyclopropenyl cation has been reviewed in this article. The structures of heavier analogues as well as group 13 analogues of cyclo-.

Evaluation of pore structures and cracking in cement paste exposed to elevated temperatures by X-ray computed tomography

Energy Technology Data Exchange (ETDEWEB)

Kim, Kwang Yeom, E-mail: kimky@kict.re.kr [Korea Institute of Construction Technology, 283 Goyangdae-ro, Ilsanseo-gu, Goyang 411-712 (Korea, Republic of); Yun, Tae Sup, E-mail: taesup@yonsei.ac.kr [School of Civil and Environmental Engineering, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-749 (Korea, Republic of); Park, Kwang Pil, E-mail: bamtol97@kict.re.kr [Korea Institute of Construction Technology, 283 Goyangdae-ro, Ilsanseo-gu, Goyang 411-712 (Korea, Republic of)

2013-08-15

When cement-based materials are exposed to the high temperatures induced by fire, which can rapidly cause temperatures of over 1000 °C, the changes in pore structure and density prevail. In the present study, mortar specimens were subjected to a series of increasing temperatures to explore the temperature-dependent evolution of internal pore structure. High-performance X-ray computed tomography (CT) was used to observe the evolution of temperature-induced discontinuities at the sub-millimeter level. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were employed to investigate the cause of physical changes in the heated mortar specimens. Results exhibit the changes in pore structure caused by elevated temperatures, and thermally induced fractures. We discuss the progressive formation of thermally induced fracture networks, which is a prerequisite for spalling failure of cement-based materials by fire, based on visual observations of the 3D internal structures revealed by X-ray CT.

Evaluation of pore structures and cracking in cement paste exposed to elevated temperatures by X-ray computed tomography

International Nuclear Information System (INIS)

Kim, Kwang Yeom; Yun, Tae Sup; Park, Kwang Pil

2013-01-01

When cement-based materials are exposed to the high temperatures induced by fire, which can rapidly cause temperatures of over 1000 °C, the changes in pore structure and density prevail. In the present study, mortar specimens were subjected to a series of increasing temperatures to explore the temperature-dependent evolution of internal pore structure. High-performance X-ray computed tomography (CT) was used to observe the evolution of temperature-induced discontinuities at the sub-millimeter level. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were employed to investigate the cause of physical changes in the heated mortar specimens. Results exhibit the changes in pore structure caused by elevated temperatures, and thermally induced fractures. We discuss the progressive formation of thermally induced fracture networks, which is a prerequisite for spalling failure of cement-based materials by fire, based on visual observations of the 3D internal structures revealed by X-ray CT

Five-membered ring annelation in [2.2]paracyclophanes by aldol condensation

Directory of Open Access Journals (Sweden)

Henning Hopf

2014-08-01

Full Text Available Under basic conditions 4,5,12,13-tetraacetyl[2.2]paracyclophane (9 cyclizes by a double aldol condensation to provide the two aldols 12 and 15 in a 3:7 ratio. The structures of these compounds were obtained from X-ray structural analysis, spectroscopic data, and mechanistic considerations. On acid treatment 12 is dehydrated to a mixture of the condensed five-membered [2.2]paracyclophane derivatives 18–20, whereas 15 yields a mixture of the isomeric cyclopentadienones 21–23. The structures of these elimination products are also deduced from X-ray and spectroscopic data. The sequence presented here constitutes the simplest route so far to cyclophanes carrying an annelated five-membered ring.

Elevational gradients in phylogenetic structure of ant communities reveal the interplay of biotic and abiotic constraints on diversity

DEFF Research Database (Denmark)

Machac, Antonin; Janda, Milan; Dunn, Robert R.

2011-01-01

A central focus of ecology and biogeography is to determine the factors that govern spatial variation in biodiversity. Here, we examined patterns of ant diversity along climatic gradients in three temperate montane systems: Great Smoky Mountains National Park (USA), Chiricahua Mountains (USA......), and Vorarlberg (Austria). To identify the factors which potentially shape these elevational diversity gradients, we analyzed patterns of community phylogenetic structure (i.e. the evolutionary relationships among species coexisting in local communities). We found that species at low-elevation sites tended...... to be evenly dispersed across phylogeny, suggesting that these communities are structured by interspecific competition. In contrast, species occurring at high-elevation sites tended to be more closely related than expected by chance, implying that these communities are structured primarily by environmental...

Rules for the analysis of mechanical structures at elevated temperatures

International Nuclear Information System (INIS)

Jakubowicz, H.; Petrequin, P.; Schaller, K.

1979-01-01

This paper describes how the experience gained by the CEA (French Atomic Energy Commission) in design, construction and operation of pool type LMFBR, as well as in research an development, is used to establish rules for the analysis of mechanical structures at elevated temperatures. These rules are written by different working groups and approved by a committee named RAMSES. The working methods of the RAMSES committee are described. Some of the approved recommendations are presented. The ongoing work and futur topics are also described

Simulation and modeling of the crushing behavior of structural members

International Nuclear Information System (INIS)

Toi, Yutaka

1986-01-01

The analysis of the crushing behavior (the behavior of compressive breakdown accompanied by super large deformation) of structural members is an important subject which becomes the base of the ultimate strength design of the structures which may cause collision accident such as automobiles, ships and aircrafts, and of those which are feared to be collided such as offshore structures, bridge piers and nuclear power plants. However, since it is a phenomenon of very strong nonlinearity, its analysis is accompanied by large difficulty. In this report, three kinds of the approach for this problem, that is, rigid-plastic theoretical analysis, the simulation using a rigid body and spring model and nonlinear finite element analysis, are explained, referring to the example of calculation by the authors on the non-axisymmetric crushing problem of cylindrical shells. In crushing problem, the matters of concern are the amount of collision energy which can be absorbed by the plastic deformation of structures and the amount of deformation. It can be said that the increase of calculation cost brings about the heightening of calculation accuracy. The nonlinear finite element analysis is promising because its calculation cost is expected to lower in future. (Kako, I.)

Dual swing-up elevator well drilling apparatus

Energy Technology Data Exchange (ETDEWEB)

Ahmad, H.; Vorarittinapa, T.

1984-09-18

A well drilling apparatus includes a first swing-up elevator platform on which the mast structure is pivotally mounted. After the mast structure has been raised to its erect position, the first elevator platform is elevated to carry the mast structure to a high operational level. A second swing-up elevator platform is provided to carry the drawworks to the same high level at which the two elevator platforms are coupled together to form the working floor. All of the raising and elevating operations can be accomplished with power supplied by the drawworks. The elevator platforms may be lowered after the drilling operation has been accomplished without interfering with any control valve structures that have been placed on the wellhead while the structure was at its raised operational level; the swing-up elevator platforms swing down in opposite directions over any such valve structure.

Elevated CO2 enhances biological contributions to elevation change in coastal wetlands by offsetting stressors associated with sea-level rise

Science.gov (United States)

Cherry, J.A.; McKee, K.L.; Grace, J.B.

2009-01-01

1. Sea-level rise, one indirect consequence of increasing atmospheric CO2, poses a major challenge to long-term stability of coastal wetlands. An important question is whether direct effects of elevated CO 2 on the capacity of marsh plants to accrete organic material and to maintain surface elevations outweigh indirect negative effects of stressors associated with sea-level rise (salinity and flooding). 2. In this study, we used a mesocosm approach to examine potential direct and indirect effects of atmospheric CO2 concentration, salinity and flooding on elevation change in a brackish marsh community dominated by a C3 species, Schoenoplectus americanus, and a C4 grass, Spartina patens. This experimental design permitted identification of mechanisms and their role in controlling elevation change, and the development of models that can be tested in the field. 3. To test hypotheses related to CO2 and sea-level rise, we used conventional anova procedures in conjunction with structural equation modelling (SEM). SEM explained 78% of the variability in elevation change and showed the direct, positive effect of S. americanus production on elevation. The SEM indicated that C3 plant response was influenced by interactive effects between CO2 and salinity on plant growth, not a direct CO2 fertilization effect. Elevated CO2 ameliorated negative effects of salinity on S. americanus and enhanced biomass contribution to elevation. 4. The positive relationship between S. americanus production and elevation change can be explained by shoot-base expansion under elevated CO 2 conditions, which led to vertical soil displacement. While the response of this species may differ under other environmental conditions, shoot-base expansion and the general contribution of C3 plant production to elevation change may be an important mechanism contributing to soil expansion and elevation gain in other coastal wetlands. 5. Synthesis. Our results revealed previously unrecognized interactions and

Boron--epoxy tubular structure members

Science.gov (United States)

Shakespeare, W. B. J.; Nelson, P. T.; Lindkvist, E. C.

1973-01-01

Composite materials fabricate thin-walled tubular members which have same load-carrying capabilities as aluminum, titanium, or other metals, but are lighter. Interface between stepped end fitting and tube lends itself to attachments by primary as well as secondary bonding. Interlaminar shear and hoop stress buildup in attachment at end fitting is avoided.

Effect of Elevated CO2 Concentration, Elevated Temperature and No Nitrogen Fertilization on Methanogenic Archaeal and Methane-Oxidizing Bacterial Community Structures in Paddy Soil.

Science.gov (United States)

Liu, Dongyan; Tago, Kanako; Hayatsu, Masahito; Tokida, Takeshi; Sakai, Hidemitsu; Nakamura, Hirofumi; Usui, Yasuhiro; Hasegawa, Toshihiro; Asakawa, Susumu

2016-09-29

Elevated concentrations of atmospheric CO2 ([CO2]) enhance the production and emission of methane in paddy fields. In the present study, the effects of elevated [CO2], elevated temperature (ET), and no nitrogen fertilization (LN) on methanogenic archaeal and methane-oxidizing bacterial community structures in a free-air CO2 enrichment (FACE) experimental paddy field were investigated by PCR-DGGE and real-time quantitative PCR. Soil samples were collected from the upper and lower soil layers at the rice panicle initiation (PI) and mid-ripening (MR) stages. The composition of the methanogenic archaeal community in the upper and lower soil layers was not markedly affected by the elevated [CO2], ET, or LN condition. The abundance of the methanogenic archaeal community in the upper and lower soil layers was also not affected by elevated [CO2] or ET, but was significantly increased at the rice PI stage and significantly decreased by LN in the lower soil layer. In contrast, the composition of the methane-oxidizing bacterial community was affected by rice-growing stages in the upper soil layer. The abundance of methane-oxidizing bacteria was significantly decreased by elevated [CO2] and LN in both soil layers at the rice MR stage and by ET in the upper soil layer. The ratio of mcrA/pmoA genes correlated with methane emission from ambient and FACE paddy plots at the PI stage. These results indicate that the decrease observed in the abundance of methane-oxidizing bacteria was related to increased methane emission from the paddy field under the elevated [CO2], ET, and LN conditions.

Materials Delivered by Member States

International Nuclear Information System (INIS)

1969-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 30 June 1969 in compliance with requests the Agency had made under Article IX. D

Ion Elevators and Escalators in Multilevel Structures for Lossless Ion Manipulations.

Science.gov (United States)

Ibrahim, Yehia M; Hamid, Ahmed M; Cox, Jonathan T; Garimella, Sandilya V B; Smith, Richard D

2017-02-07

We describe two approaches based upon ion "elevator" and "escalator" components that allow moving ions to different levels in structures for lossless ion manipulations (SLIM). Guided by ion motion simulations, we designed elevator and escalator components based upon ion current measurements providing essentially lossless transmission in multilevel designs. The ion elevator design allowed ions to efficiently bridge a 4 mm gap between levels. The component was integrated in a SLIM and coupled to a QTOF mass spectrometer using an ion funnel interface to evaluate the m/z range transmitted as compared to transmission within a level (e.g., in a linear section). The analysis of singly charged ions of m/z 600-2700 produced similar mass spectra for both elevator and straight (linear motion) components. In the ion escalator design, traveling waves (TW) were utilized to transport ions efficiently between two SLIM levels. Ion current measurements and ion mobility (IM) spectrometry analysis illustrated that ions can be transported between TW-SLIM levels with no significant loss of either ions or IM resolution. These developments provide a path for the development of multilevel designs providing, e.g., much longer IM path lengths, more compact designs, and the implementation of much more complex SLIM devices in which, e.g., different levels may operate at different temperatures or with different gases.

Probabilistic Analysis of Structural Member from Recycled Aggregate Concrete

Science.gov (United States)

Broukalová, I.; Šeps, K.

2017-09-01

The paper aims at the topic of sustainable building concerning recycling of waste rubble concrete from demolition. Considering demands of maximising recycled aggregate use and minimising of cement consumption, composite from recycled concrete aggregate was proposed. The objective of the presented investigations was to verify feasibility of the recycled aggregate cement based fibre reinforced composite in a structural member. Reliability of wall from recycled aggregate fibre reinforced composite was assessed in a probabilistic analysis of a load-bearing capacity of the wall. The applicability of recycled aggregate fibre reinforced concrete in structural applications was demonstrated. The outcomes refer to issue of high scatter of material parameters of recycled aggregate concretes.

Influences of vegetation structure and elevation on CO2 uptake in a mature jack pine forest in Saskatchewan, Canada

International Nuclear Information System (INIS)

Chasmer, L.; McCaughey, H.; Treitz, P.

2008-01-01

Eddy covariance (EC) is often used to measure the movement and direction of energy and trace gas concentrations in ecosystems. Data from EC networks are often combined with remote sensing data and ecosystem models in order to assess the spatial and temporal variability of carbon dioxide (CO 2 ) exchanges within specific areas of interest. This study presented a new method of determining changes in the structural characteristics of biomass and elevation. Lidar was used within the contours of half-hourly flux footprint areas to characterize vegetation structure and elevation. The influences of vegetation structure and elevation on CO 2 concentrations were measured by EC and Lidar measurements for 3 mature growing periods at a mature jack pine site in Saskatchewan. Mensuration data were collected over 2 periods. Meteorological, CO 2 , and H2O flux measurements were collected for 30 minute periods each day. Statistical analyses were conducted to determine the influence of meteorological variables on vegetation structure. Footprint contour lines were then layered onto the canopy height models derived by the lidar data. Multiple regression equations were used to determine net ecosystem productivity (NEP) and gross ecosystem productivity (GEP) using meteorological variables, canopy fractional cover; and elevation, as well as the results obtained from a Landsberg equation. The study showed that differences in NEP variability were influenced by differences in canopy and ground surface characteristics within the site. EC measurements underestimated gross CO 2 fluxes by 5 per cent as the biomass was lower within the immediate vicinity of the EC network. It was concluded that canopy structures and elevation are important factors for determining annual carbon balances. 36 refs., 8 tabs., 9 figs

Effect of elevated temperatures on heavy concrete structural strength in Qinshan phase 3 CANDU 6 reactor buildings

International Nuclear Information System (INIS)

Alikhan, S.; Khan, A.F.; Chen, S.

2005-01-01

Heavy concrete is commonly used inside the Qinshan Phase 3 CANDU 6 reactor buildings for radiation shielding functions in order to provide access to key areas during reactor operation. In some cases, the heavy concrete elements are also structural elements. Concerns have been raised about the functional performance of the heavy concrete structural elements, specifically the primary heat transport pump (PHTS) supporting slabs, surrounding the feeder cabinets when subjected to elevated temperatures between 42 degree C and 121 degree C and their corresponding temperature gradients on a long-term basis during the normal operation of the plant. This paper presents the results of a test investigation on the strength of heavy concrete under elevated temperature conditions being experienced by the heavy concrete structural elements around the feeder cabinet to confirm that these structural elements meet their functional requirements. The loading conditions consist subjecting the specimens to the elevated temperatures and temperature gradient noted during commissioning, including the effect of epoxy coating. The heavy concrete mix proportion and materials of the test samples (ilmenite aggregate and Portland cement) are identical to those used for heavy concrete structural elements surrounding the feeder cabinet. Subsequent to the confirmation of the functional requirements of the heavy concrete structural elements, alarm limits are recommended for these structural elements. (authors)

A Review of the Effects of Elevated Temperature on Concrete Materials and Structures

International Nuclear Information System (INIS)

Naus, D.J.; Graves, H.L. III

2006-01-01

Concrete's properties are more complex than those of most materials because not only is concrete a composite material whose constituents have different properties, but its properties depend upon moisture and porosity. Exposure of concrete to elevated temperature affects its mechanical and physical properties. Elements could distort and displace, and, under certain conditions, the concrete surfaces could spall due to the buildup of steam pressure. Because thermally-induced dimensional changes, loss of structural integrity, and release of moisture and gases resulting from the migration of free water could adversely affect plant operations and safety, a complete understanding of the behavior of concrete under long-term elevated-temperature exposure as well as both during and after a thermal excursion resulting from a postulated design-basis accident condition is essential for reliable design evaluations and assessments of nuclear power plant structures. As the properties of concrete change with respect to time and the environment to which it is exposed, an assessment of the effects of concrete aging is also important in performing safety evaluations. The effects of elevated temperature on Portland cement concretes and constituent materials are summarized, design codes and standards identified, and considerations for elevated temperature service noted. (authors)

A Review on the Use of Agriculture Waste Material as Lightweight Aggregate for Reinforced Concrete Structural Members

Directory of Open Access Journals (Sweden)

Kim Hung Mo

2014-01-01

Full Text Available The agriculture industry is one of the main industries in the Southeast Asia region due to its favourable conditions for plantations. In fact, Southeast Asia region is the world’s largest producer of palm oil and coconut. Nevertheless, vast plantation of these agriculture products leads to equally large amount of waste materials emanating from these industries. Previously, researchers have attempted to utilize the resulting waste materials such as oil palm shell, palm oil clinker, and coconut shell from these industries as lightweight aggregate to produce structural grade lightweight aggregate concrete. In order to promote the concept of using such concrete for actual structural applications, this paper reviews the use of such agriculture-based lightweight aggregate concrete in reinforced concrete structural members such as beam and slab, which were carried out by researchers in the past. The behaviour of the structural members under flexural, shear, and torsional load was also summarized. It is hoped that the knowledge attained from the paper will provide design engineers with better idea and proper application of design criteria for structural members using such agriculture waste as lightweight aggregate.

Radio frequency-induced temperature elevations in the human head considering small anatomical structures

International Nuclear Information System (INIS)

Schmid, G.; Ueberbacher, R.; Samaras, T.

2007-01-01

In order to enable a detailed numerical radio frequency (RF) dosimetry and the computations of RF-induced temperature elevations, high-resolution (0.1 mm) numerical models of the human eye, the inner ear organs and the pineal gland were developed and inserted into a commercially available head model. As radiation sources, generic models of handsets at 400, 900 and 1850 MHz operating in close proximity to the head were considered. The results, obtained by finite-difference time domain-based computations, showed a highly heterogeneous specific absorption rate (SAR) distribution and SAR-peaks inside the inner ear structures; however, the corresponding RF-induced temperature elevations were well below 0.1 deg. C, when considering typical output power values of hand-held devices. In case of frontal exposure, with the radiation sources ∼2.5 cm in front of the closed eye, maximum temperature elevations in the eye in the range of ∼0.2-0.6 deg. C were found for typical device output powers. A reduction in tissue perfusion mainly affected the maximum RF-induced temperature elevation of tissues deep inside the head. Similarly, worst-case considerations regarding pulsed irradiation affected temperature elevations in deep tissue significantly more than in superficial tissues. (authors)

A technique of the structural-tectonic elevations prediction using Earth remote sensing data

Science.gov (United States)

Tishaev, I. V.; Zatserkovnyi, V. I.; Yagorlytska, K. P.

2016-12-01

We consider an approach of using methods of Earth remote sensing data (RSD) classification for solving tasks of exploration geology and geophysics. Information obtained from the remote sensing data gives a possibility to clarify the structure of investigated areas and to determine neotectonic elevations, which act as certain indicators of promising areas with hydra-carbons contents. Reasonability of using such methods of RSD classification is based on connection between deep structure of surface resources (structural-tectonic setting) with current landscape, character of hydrologic network, geo-morphological, geo-botanical and other features. The advantage of Bayes classificator is not only in determination of object belonging to certain class, but also in calculation of probability of such belonging. For the formulated task this lets to forecast a presence of structural-tectonic elevations, which are potentially promising areas for hydra-carbons contents, using a formali! zed quantitative criterion. contents.

Elevation Extraction and Deformation Monitoring by Multitemporal InSAR of Lupu Bridge in Shanghai

Directory of Open Access Journals (Sweden)

Jingwen Zhao

2017-08-01

Full Text Available Monitoring, assessing, and understanding the structural health of large infrastructures, such as buildings, bridges, dams, tunnels, and highways, is important for urban development and management, as the gradual deterioration of such structures may result in catastrophic structural failure leading to high personal and economic losses. With a higher spatial resolution and a shorter revisit period, interferometric synthetic aperture radar (InSAR plays an increasing role in the deformation monitoring and height extraction of structures. As a focal point of the InSAR data processing chain, phase unwrapping has a direct impact on the accuracy of the results. In complex urban areas, large elevation differences between the top and bottom parts of a large structure combined with a long interferometric baseline can result in a serious phase-wrapping problem. Here, with no accurate digital surface model (DSM available, we handle the large phase gradients of arcs in multitemporal InSAR processing using a long–short baseline iteration method. Specifically, groups of interferometric pairs with short baselines are processed to obtain the rough initial elevation estimations of the persistent scatterers (PSs. The baseline threshold is then loosened in subsequent iterations to improve the accuracy of the elevation estimates step by step. The LLL lattice reduction algorithm (by Lenstra, Lenstra, and Lovász is applied in the InSAR phase unwrapping process to rapidly reduce the search radius, compress the search space, and improve the success rate in resolving the phase ambiguities. Once the elevations of the selected PSs are determined, they are used in the following two-dimensional phase regression involving both elevations and deformations. A case study of Lupu Bridge in Shanghai is carried out for the algorithm’s verification. The estimated PS elevations agree well (within 1 m with the official Lupu Bridge model data, while the PS deformation time series

Structural characteristics and elevated temperature mechanical properties of AJ62 Mg alloy

Energy Technology Data Exchange (ETDEWEB)

Kubásek, J., E-mail: Jiri.Kubasek@vscht.cz; Vojtěch, D.; Martínek, M.

2013-12-15

Structure and mechanical properties of the novel casting AJ62 (Mg–6Al–2Sr) alloy developed for elevated temperature applications were studied. The AJ62 alloy was compared to commercial casting AZ91 (Mg–9Al–1Zn) and WE43 (Mg–4Y–3RE) alloys. The structure was examined by scanning electron microscopy, x-ray diffraction and energy dispersive spectrometry. Mechanical properties were characterized by Viskers hardness measurements in the as-cast state and after a long-term heat treatment at 250 °C/150 hours. Compressive mechanical tests were also carried out both at room and elevated temperatures. Compressive creep tests were conducted at a temperature of 250 °C and compressive stresses of 60, 100 and 140 MPa. The structure of the AJ62 alloy consisted of primary α-Mg dendrites and interdendritic nework of the Al{sub 4}Sr and massive Al{sub 3}Mg{sub 13}Sr phases. By increasing the cooling rate during solidification from 10 and 120 K/s the average dendrite arm thickness decreased from 18 to 5 μm and the total volume fraction of the interdendritic phases from 20% to 30%. Both factors slightly increased hardness and compressive strength. The room temperature compressive strength and hardness of the alloy solidified at 30 K/s were 298 MPa and 50 HV 5, i.e. similar to those of the as-cast WE43 alloy and lower than those of the AZ91 alloy. At 250 °C the compressive strength of the AJ62 alloy decreased by 50 MPa, whereas those of the AZ91 and WE43 alloys by 100 and 20 MPa, respectively. The creep rate of the AJ62 alloy was higher than that of the WE43 alloy, but significantly lower in comparison with the AZ91 alloy. Different thermal stabilities of the alloys were discussed and related to structural changes during elevated temperature expositions. - Highlights: • Small effect of cooling rate on the compressive strength and hardness of AJ 62 • A bit lower compressive strength of AJ 62 compared to AZ91 at room temperature • Higher resistance of the AJ 62

Development of advanced earthquake resistant performance verification on reinforced concrete underground structures. Pt. 3. Applicability of soil-structure Interaction analysis using nonlinear member model

International Nuclear Information System (INIS)

Matsui, Jun; Ohtomo, Keizo; Kawai, Tadashi; Kanatani, Mamoru; Matsuo, Toyofumi

2003-01-01

The objective of this study is to obtain verification data concerning performance of RC duct-type underground structures subject to strong earth quakes. This paper presents the investigated results of numerical simulation obtained from shaking table tests of box-type structure models with a scale of about 1/2. We proposed practical nonlinear member models, by which mechanical properties of RC member and soil are defined as hysteresis models (RC: axial force dependent degrading tri-linear model, soil: modified Ramberg-Osgood model), and joint elements are used to evaluate the interaction along the interface of two materials between soil and RC structures; including the slippage and separation. Consequently, the proposed models could simulate the test results on the deformation of soil and RC structure, as well as damage of RC structures which is important in verifying their seismic performance with practical accuracy. (author)

Examining conifer canopy structural complexity across forest ages and elevations with LiDAR data

Science.gov (United States)

Van R. Kane; Jonathan D. Bakker; Robert J. McGaughey; James A. Lutz; Rolf F. Gersonde; Jerry F. Franklin

2010-01-01

LiDAR measurements of canopy structure can be used to classify forest stands into structural stages to study spatial patterns of canopy structure, identify habitat, or plan management actions. A key assumption in this process is that differences in canopy structure based on forest age and elevation are consistent with predictions from models of stand development. Three...

The space station tethered elevator system

Science.gov (United States)

Anderson, Loren A.

1989-01-01

The optimized conceptual engineering design of a space station tethered elevator is presented. The elevator is an unmanned mobile structure which operates on a ten kilometer tether spanning the distance between the Space Station and a tethered platform. Elevator capabilities include providing access to residual gravity levels, remote servicing, and transportation to any point along a tether. The potential uses, parameters, and evolution of the spacecraft design are discussed. Engineering development of the tethered elevator is the result of work conducted in the following areas: structural configurations; robotics, drive mechanisms; and power generation and transmission systems. The structural configuration of the elevator is presented. The structure supports, houses, and protects all systems on board the elevator. The implementation of robotics on board the elevator is discussed. Elevator robotics allow for the deployment, retrieval, and manipulation of tethered objects. Robotic manipulators also aid in hooking the elevator on a tether. Critical to the operation of the tethered elevator is the design of its drive mechanisms, which are discussed. Two drivers, located internal to the elevator, propel the vehicle along a tether. These modular components consist of endless toothed belts, shunt-wound motors, regenerative power braking, and computer controlled linear actuators. The designs of self-sufficient power generation and transmission systems are reviewed. Thorough research indicates all components of the elevator will operate under power provided by fuel cells. The fuel cell systems will power the vehicle at seven kilowatts continuously and twelve kilowatts maximally. A set of secondary fuel cells provides redundancy in the unlikely event of a primary system failure. Power storage exists in the form of Nickel-Hydrogen batteries capable of powering the elevator under maximum loads.

Contrasting elevational diversity patterns for soil bacteria between two ecosystems divided by the treeline.

Science.gov (United States)

Li, Guixiang; Xu, Guorui; Shen, Congcong; Tang, Yong; Zhang, Yuxin; Ma, Keming

2016-11-01

Above- and below-ground organisms are closely linked, but how elevational distribution pattern of soil microbes shifting across the treeline still remains unknown. Sampling of 140 plots with transect, we herein investigated soil bacterial distribution pattern from a temperate forest up to a subalpine meadow along an elevational gradient using Illumina sequencing. Our results revealed distinct elevational patterns of bacterial diversity above and below the treeline in responding to changes in soil conditions: a hollow elevational pattern in the forest (correlated with soil temperature, pH, and C:N ratio) and a significantly decreasing pattern in the meadow (correlated with soil pH, and available phosphorus). The bacterial community structure was also distinct between the forest and meadow, relating to soil pH in the forest and soil temperature in the meadow. Soil bacteria did not follow the distribution pattern of herb diversity, but bacterial community structure could be predicted by herb community composition. These results suggest that plant communities have an important influence on soil characteristics, and thus change the elevational distribution of soil bacteria. Our findings are useful for future assessments of climate change impacts on microbial community.

Elevator mechanism and method for scintillation detectors

International Nuclear Information System (INIS)

Frank, E.

1975-01-01

An elevator mechanism and method for raising and lowering radioactive samples through a shielded vertical counting chamber in a benchtop scintillation detector is described. The elevator mechanism adds little or nothing to the height of the detector by using an elongated flexible member such as a metal tape secured to the bottom of the elevator platform and extending downwardly through the counting chamber and its bottom shielding, where the tape is bent laterally for connection to a drive means. In the particular embodiment illustrated, the tape is bent laterally below the bottom shielding for the counting chamber, and then upwardly along or through one side of the shielding to a reel at the top of the shielding. The tape is wound onto the reel, and the reel is driven by a reversible motor which winds and unwinds the tape on the reel to raise and lower the elevator platform

E2F family members are differentially regulated by reversible acetylation

DEFF Research Database (Denmark)

Marzio, G; Wagener, C; Gutierrez, M I

2000-01-01

of the other E2F family members. Here we report that E2F-1, -2, and -3, but not E2F-4, -5, and -6, associate with and are acetylated by p300 and cAMP-response element-binding protein acetyltransferases. Acetylation occurs at three conserved lysine residues located at the N-terminal boundary of their DNA......The six members of the E2F family of transcription factors play a key role in the control of cell cycle progression by regulating the expression of genes involved in DNA replication and cell proliferation. E2F-1, -2, and -3 belong to a structural and functional subfamily distinct from those...

Materials Delivered by Member States

International Nuclear Information System (INIS)

1966-01-01

The information given in this document is divided into two parts. In part I the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 31 December 1965 in compliance with requests the Agency had made under Article IX. D. Part III contains information about materials which had not been delivered by 31 December but which had been allocated, in accordance with Article XI. F. 1 of the Statute, to approved Agency projects for which project arrangements were in force on that date

Materials Delivered by Member States

International Nuclear Information System (INIS)

1965-01-01

The information given in this document is divided into two parts. In part I the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 31 December 1964 in compliance with requests the Agency had made under Article IX. D. Part II contains information about materials which had not been delivered by 31 December but which had been allocated, in accordance with Article XI. F. 1 of the Statute, to approved Agency projects for which project arrangements were in force on that date

Materials Delivered by Member States

International Nuclear Information System (INIS)

1968-01-01

The information given in this document is divided into two parts. In part I the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered by Members up to 30 June 1968 in compliance with requests the Agency had made under Article IX,D. Part II contains information about materials which had not been delivered by 30 June 1968 but which had been allocated, in accordance with Article XI.F.I of the Statute, to approved Agency projects for which project arrangements were in force on that date

Ion Elevators and Escalators in Multilevel Structures for Lossless Ion Manipulations

Energy Technology Data Exchange (ETDEWEB)

Ibrahim, Yehia M.; Hamid, Ahmed M.; Cox, Jonathan T.; Garimella, Venkata BS; Smith, Richard D.

2017-01-19

We describe two approaches based upon ion ‘elevator’ and ‘escalator’ components that allow moving ions to different levels in structures for lossless ion manipulations (SLIM). Guided by ion motion simulations we designed elevator and escalator components providing essentially lossless transmission in multi-level designs based upon ion current measurements. The ion elevator design allowed ions to efficiently bridge a 4 mm gap between levels. The component was integrated in a SLIM and coupled to a QTOF mass spectrometer using an ion funnel interface to evaluate the m/z range transmitted as compared to transmission within a level (e.g. in a linear section). Mass spectra for singly-charged ions of m/z 600-2700 produced similar mass spectra for both elevator and straight (linear motion) components. In the ion escalator design, traveling waves (TW) were utilized to transport ions efficiently between two SLIM levels. Ion current measurements and ion mobility (IM) spectrometry analysis illustrated that ions can be transported between TW-SLIM levels with no significant loss of either ions or IM resolution. These developments provide a path for the development of multilevel designs providing e.g. much longer IM path lengths, more compact designs, and the implementation of much more complex SLIM devices in which e.g. different levels may operate at different temperatures or with different gases.

Solution structure and elevator mechanism of the membrane electron transporter CcdA.

Science.gov (United States)

Zhou, Yunpeng; Bushweller, John H

2018-02-01

Membrane oxidoreductase CcdA plays a central role in supplying reducing equivalents from the bacterial cytoplasm to the envelope. It transports electrons across the membrane using a single pair of cysteines by a mechanism that has not yet been elucidated. Here we report an NMR structure of the Thermus thermophilus CcdA (TtCcdA) in an oxidized and outward-facing state. CcdA consists of two inverted structural repeats of three transmembrane helices (2 × 3-TM). We computationally modeled and experimentally validated an inward-facing state, which suggests that CcdA uses an elevator-type movement to shuttle the reactive cysteines across the membrane. CcdA belongs to the LysE superfamily, and thus its structure may be relevant to other LysE clan transporters. Structure comparisons of CcdA, semiSWEET, Pnu, and major facilitator superfamily (MFS) transporters provide insights into membrane transporter architecture and mechanism.

Aspect has a greater impact on alpine soil bacterial community structure than elevation.

Science.gov (United States)

Wu, Jieyun; Anderson, Barbara J; Buckley, Hannah L; Lewis, Gillian; Lear, Gavin

2017-03-01

Gradients in environmental conditions, including climate factors and resource availability, occur along mountain inclines, providing a 'natural laboratory' to explore their combined impacts on microbial distributions. Conflicting spatial patterns observed across elevation gradients in soil bacterial community structure suggest that they are driven by various interacting factors at different spatial scales. Here, we investigated the relative impacts of non-resource (e.g. soil temperature, pH) and resource conditions (e.g. soil carbon and nitrogen) on the biogeography of soil bacterial communities across broad (i.e. along a 1500 m mountain elevation gradient) and fine sampling scales (i.e. along sunny and shady aspects of a mountain ridge). Our analysis of 16S rRNA gene data confirmed that when sampling across distances of soil pH. These findings highlight the need to incorporate knowledge of multiple factors, including site aspect and soil pH for the appropriate use of elevation gradients as a proxy to explore the impacts of climate change on microbial community composition. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Control of minimum member size in parameter-free structural shape optimization by a medial axis approximation

Science.gov (United States)

Schmitt, Oliver; Steinmann, Paul

2017-09-01

We introduce a manufacturing constraint for controlling the minimum member size in structural shape optimization problems, which is for example of interest for components fabricated in a molding process. In a parameter-free approach, whereby the coordinates of the FE boundary nodes are used as design variables, the challenging task is to find a generally valid definition for the thickness of non-parametric geometries in terms of their boundary nodes. Therefore we use the medial axis, which is the union of all points with at least two closest points on the boundary of the domain. Since the effort for the exact computation of the medial axis of geometries given by their FE discretization highly increases with the number of surface elements we use the distance function instead to approximate the medial axis by a cloud of points. The approximation is demonstrated on three 2D examples. Moreover, the formulation of a minimum thickness constraint is applied to a sensitivity-based shape optimization problem of one 2D and one 3D model.

Elevated expression and potential roles of human Sp5, a member of Sp transcription factor family, in human cancers

International Nuclear Information System (INIS)

Chen Yongxin; Guo Yingqiu; Ge Xijin; Itoh, Hirotaka; Watanabe, Akira; Fujiwara, Takeshi; Kodama, Tatsuhiko; Aburatani, Hiroyuki

2006-01-01

In this report, we describe the expression and function of human Sp5, a member of the Sp family of zinc finger transcription factors. Like other family members, the Sp5 protein contains a Cys2His2 zinc finger DNA binding domain at the C-terminus. Our experiments employing Gal4-Sp5 fusion proteins reveal multiple transcriptional domains, including a N-terminal activity domain, an intrinsic repressive element, and a C-terminal synergistic domain. Elevated expression of Sp5 was noted in several human tumors including hepatocellular carcinoma, gastric cancer, and colon cancer. To study the effects of the Sp5 protein on growth properties of human cancer cells and facilitate the identification of its downstream genes, we combined an inducible gene expression system with microarray analysis to screen for its transcriptional targets. Transfer of Sp5 into MCF-7 cells that expressed no detectable endogenous Sp5 protein elicited significant growth promotion activity. Several of the constitutively deregulated genes have been associated with tumorigenesis (CDC25C, CEACAM6, TMPRSS2, XBP1, MYBL1, ABHD2, and CXCL12) and Wnt/β-Catenin signaling pathways (BAMBI, SIX1, IGFBP5, AES, and p21 WAF1 ). This information could be utilized for further mechanistic research and for devising optimized therapeutic strategies against human cancers

Design of reinforced concrete members based on structural mechanics

International Nuclear Information System (INIS)

Diaz, B.E.; Schulz, M.

1984-01-01

Up to now the design of reinforced concrete linear members is performed with the help of an inconsistent design theory, which nevertherless is sufficiently safe and simple to be used in the practice. The purpose of this paper is to present a rational reinforced concrete design method which is not too dissimilar to the present design rules, but is capable of defining consistently internal stresses along a reinforced concrete section. The present status of the completed computer procedures allows the analysis of linear reinforced concrete members formed by laminar reinforced concrete plates presenting variable thickness. A practical approach is presented for which the concrete and steel section is constant along the member axis. In this case, the concept of the equivalent section is introduced, which allows a simple analysis of the stress pattern along the member section. (Author) [pt

Bacterial community structure in experimental methanogenic bioreactors and search for pathogenic clostridia as community members.

Science.gov (United States)

Dohrmann, Anja B; Baumert, Susann; Klingebiel, Lars; Weiland, Peter; Tebbe, Christoph C

2011-03-01

Microbial conversion of organic waste or harvested plant material into biogas has become an attractive technology for energy production. Biogas is produced in reactors under anaerobic conditions by a consortium of microorganisms which commonly include bacteria of the genus Clostridium. Since the genus Clostridium also harbors some highly pathogenic members in its phylogenetic cluster I, there has been some concern that an unintended growth of such pathogens might occur during the fermentation process. Therefore this study aimed to follow how process parameters affect the diversity of Bacteria in general, and the diversity of Clostridium cluster I members in particular. The development of both communities was followed in model biogas reactors from start-up during stable methanogenic conditions. The biogas reactors were run with either cattle or pig manures as substrates, and both were operated at mesophilic and thermophilic conditions. The structural diversity was analyzed independent of cultivation using a PCR-based detection of 16S rRNA genes and genetic profiling by single-strand conformation polymorphism (SSCP). Genetic profiles indicated that both bacterial and clostridial communities evolved in parallel, and the community structures were highly influenced by both substrate and temperature. Sequence analysis of 16S rRNA genes recovered from prominent bands from SSCP profiles representing Clostridia detected no pathogenic species. Thus, this study gave no indication that pathogenic clostridia would be enriched as dominant community members in biogas reactors fed with manure.

"Ultra"-Fast Fracture Strength of Advanced Structural Ceramic Materials Studied at Elevated Temperatures

Science.gov (United States)

Choi, Sung R.; Gyekenyesi, John P.

1999-01-01

The accurate determination of inert strength is important in reliable life prediction of structural ceramic components. At ambient temperature, the inert strength of a brittle material is typically regarded as free of the effects of slow crack growth due to stress corrosion. Therefore, the inert strength can be determined either by eliminating active species, especially moisture, with an appropriate inert medium, or by using a very high test rate. However, at elevated temperatures, the concept or definition of the inert strength of brittle ceramic materials is not clear, since temperature itself is a degrading environment, resulting in strength degradation through slow crack growth and/or creep. Since the mechanism to control strength is rate-dependent viscous flow, the only conceivable way to determine the inert strength at elevated temperatures is to utilize a very fast test rate that either minimizes the time for or eliminates slow crack growth. Few experimental studies have measured the elevated-temperature, inert (or "ultra"-fast fracture) strength of advanced ceramics. At the NASA Lewis Research Center, an experimental study was initiated to better understand the "ultra"-fast fracture strength behavior of advanced ceramics at elevated temperatures. Fourteen advanced ceramics - one alumina, eleven silicon nitrides, and two silicon carbides - have been tested using constant stress-rate (dynamic fatigue) testing in flexure with a series of stress rates including the "ultra"-fast stress rate of 33 000 MPa/sec with digitally controlled test frames. The results for these 14 advanced ceramics indicate that, notwithstanding possible changes in flaw populations as well as flaw configurations because of elevated temperatures, the strength at 33 000 MPa/sec approached the room-temperature strength or reached a higher value than that determined at the conventional test rate of 30 MPa/sec. On the basis of the experimental data, it can be stated that the elevated

Nonlinear structural analysis methods and their application to elevated temperature design: A US perspective

International Nuclear Information System (INIS)

Dhalla, A.K.

1989-01-01

Technological advances over the last two decades have been assimilated into the routine design of Liquid Metal Reactor (LMR) structural components operating at elevated temperatures. The mature elevated temperature design technology is based upon: (a) an extensive material data base, (b) recent advances in nonlinear computational methods, and (c) conservative design criteria based upon past successful and reliable operating experiences with petrochemical and nonnuclear power plants. This survey paper provides a US perspective on the role of nonlinear analysis methods used in the design of LMR plants. The simplified and detailed nonlinear analysis methods and the level of computational effort required to qualify structural components for safe and reliable long-term operation are discussed. The paper also illustrates how a detailed nonlinear analysis can be used to resolve technical licensing issues, to understand complex nonlinear structural behavior, to identify predominant failure modes, and to guide future experimental programs

Extracting topographic structure from digital elevation data for geographic information-system analysis

Science.gov (United States)

Jenson, Susan K.; Domingue, Julia O.

1988-01-01

Software tools have been developed at the U.S. Geological Survey's EROS Data Center to extract topographic structure and to delineate watersheds and overland flow paths from digital elevation models. The tools are specialpurpose FORTRAN programs interfaced with general-purpose raster and vector spatial analysis and relational data base management packages.

Current Status of the Elevated Temperature Structure Design Codes for VHTR

International Nuclear Information System (INIS)

Kim, Jong-Bum; Kim, Seok-Hoon; Park, Keun-Bae; Lee, Won-Jae

2006-01-01

An elevated temperature structure design and analysis is one of the key issues in the VHTR (Very High Temperature Reactor) project to achieve an economic production of hydrogen which will be an essential energy source for the near future. Since the operating temperature of a VHTR is above 850 .deg. C, the existing code and standards are insufficient for a high temperature structure design. Thus the issues concerning a material selection and behaviors are being studied for the main structural components of a VHTR in leading countries such as US, France, UK, and Japan. In this study, the current status of the ASME code, French RCC-MR, UK R5, and Japanese code were investigated and the necessary R and D items were discussed

Fatigue crack detection on structural steel members by using ultrasound excited thermography

Energy Technology Data Exchange (ETDEWEB)

Plum, Robin Marc

2015-07-01

In the field of non-destructive testing (NDT), ultrasound excited thermography has been recognised as a promising technique that was successfully applied to metals, fibre composites and many more engineering materials in order to detect cracks, delaminations and other types of internal flaws. Dating back to the late 1970s, the idea of high-frequency vibration excitation of structural members combined with monitoring the surface temperature by means of infrared thermography aims at the localised energy dissipation at defect regions and its thermal detection. The purpose of this thesis is to investigate the potential use of ultrasound excited thermography for detecting surface breaking fatigue cracks in thick-walled components relevant to steel construction. The presented research is motivated by a lack of fast and imaging crack detection methods in the field and the growing acceptance and technological progress of active thermography techniques. After introducing the concept of ultrasound excited thermography or vibrothermography, its current state of the art is described by means of a comprehensive literature review focusing on research activities towards crack detection on metals. Owing to the interdisciplinarity of the test method, all relevant technical subdisciplines from the excitation of plate vibrations via potential heat generation mechanisms and heat transfer to infrared thermography are outlined. The experimental work starts with the manufacture and fatigue loading of suitable plate specimens made from low-carbon steel S355, mostly in the high cycle fatigue regime, to generate throughthickness cracks with specified depths. Using a modified high-power ultrasonic welding generator, basic dependencies of the defect heating on frequency, coupling location and excitation duration are clarified at first. Besides of an estimation of realistic detection limits depending on the plate thickness, main issues such as the relation between vibration intensity and

Fatigue crack detection on structural steel members by using ultrasound excited thermography

International Nuclear Information System (INIS)

Plum, Robin Marc

2015-01-01

In the field of non-destructive testing (NDT), ultrasound excited thermography has been recognised as a promising technique that was successfully applied to metals, fibre composites and many more engineering materials in order to detect cracks, delaminations and other types of internal flaws. Dating back to the late 1970s, the idea of high-frequency vibration excitation of structural members combined with monitoring the surface temperature by means of infrared thermography aims at the localised energy dissipation at defect regions and its thermal detection. The purpose of this thesis is to investigate the potential use of ultrasound excited thermography for detecting surface breaking fatigue cracks in thick-walled components relevant to steel construction. The presented research is motivated by a lack of fast and imaging crack detection methods in the field and the growing acceptance and technological progress of active thermography techniques. After introducing the concept of ultrasound excited thermography or vibrothermography, its current state of the art is described by means of a comprehensive literature review focusing on research activities towards crack detection on metals. Owing to the interdisciplinarity of the test method, all relevant technical subdisciplines from the excitation of plate vibrations via potential heat generation mechanisms and heat transfer to infrared thermography are outlined. The experimental work starts with the manufacture and fatigue loading of suitable plate specimens made from low-carbon steel S355, mostly in the high cycle fatigue regime, to generate throughthickness cracks with specified depths. Using a modified high-power ultrasonic welding generator, basic dependencies of the defect heating on frequency, coupling location and excitation duration are clarified at first. Besides of an estimation of realistic detection limits depending on the plate thickness, main issues such as the relation between vibration intensity and

Thin type inverter for machine-room-less elevator; Machine roomless elevator yo usugata inverter

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-01-10

In the elevator industry, a machine-room-less elevator, which does not necessitate a machine room usually installed on the roof, has come into the spotlight in the domain of low and intermediate speed elevators. The lack of a machine room, however, will necessarily limit the space for the installation of the traction motor and control panel. Fuji Electric Co., Ltd., in order to properly cope with the situation, has developed in cooperation with Fujitec Co., Ltd., a very thin type inverter installable on an elevator hall floor. The inverter, based on Fuji Electric's high-performance vector control inverter FRENIC5000VG5, is as thin as 100mm, and is available in three series up to 11kW. For the embodiment of such a thin structure, a cooling structure of Fuji Electric's own is employed, and prudence is exercised as required at many locations so that maintainability will not be impaired throughout the very thin control panel design. (translated by NEDO)

Interactive network configuration maintains bacterioplankton community structure under elevated CO2 in a eutrophic coastal mesocosm experiment

Science.gov (United States)

Lin, Xin; Huang, Ruiping; Li, Yan; Li, Futian; Wu, Yaping; Hutchins, David A.; Dai, Minhan; Gao, Kunshan

2018-01-01

There is increasing concern about the effects of ocean acidification on marine biogeochemical and ecological processes and the organisms that drive them, including marine bacteria. Here, we examine the effects of elevated CO2 on the bacterioplankton community during a mesocosm experiment using an artificial phytoplankton community in subtropical, eutrophic coastal waters of Xiamen, southern China. Through sequencing the bacterial 16S rRNA gene V3-V4 region, we found that the bacterioplankton community in this high-nutrient coastal environment was relatively resilient to changes in seawater carbonate chemistry. Based on comparative ecological network analysis, we found that elevated CO2 hardly altered the network structure of high-abundance bacterioplankton taxa but appeared to reassemble the community network of low abundance taxa. This led to relatively high resilience of the whole bacterioplankton community to the elevated CO2 level and associated chemical changes. We also observed that the Flavobacteria group, which plays an important role in the microbial carbon pump, showed higher relative abundance under the elevated CO2 condition during the early stage of the phytoplankton bloom in the mesocosms. Our results provide new insights into how elevated CO2 may influence bacterioplankton community structure.

Study on the shear transfer of reinforced concrete at elevated temperature

International Nuclear Information System (INIS)

Ishida, Hiroaki; Kanazu, Tsutomu

1989-01-01

Reinforced concrete structures in nuclear power stations, such as a containment vessel and structural members supporting a reactor vessel, are designed assuming that they may be subjected to elevated temperature. In the design code, it is specified that the temperature of concrete must not exceed the limitation, and thermal effect shall be taken into account. In this study, the shearing test using Mattock type specimens was performed to investigate into the shear behavior of the reinforced concrete subjected to elevated temperature. The test parameters studied in this program were the reinforcement ratio in a shear plane, the compressive stress normal to a shear plane and temperature. The maximum shearing load of the specimens heated to 200 degC was about 10-20 % lower than that at normal temperature, but nearly equal to that of the specimens heated to 100 degC. The equation for evaluating the shearing strength ratio was proposed. The cracking width and slip at maximum shearing load increased as temperature rose. Up to 200 degC, the same relation existed between interface shear transfer rigidity and cracking width. (K.I.)

[Use of stairs in a hospital increased by a sign near the stairs or the elevator].

Science.gov (United States)

Houweling, S T; Stoopendaal, J; Kleefstra, N; Meyboom-de Jong, B; Bilo, H J G

2005-12-24

To investigate whether signs encouraging taking the stairs or discouraging taking the elevator lead to an increasing number of patients taking the stairs instead of the elevator in a hospital. Interventional study. During a period of 6 weeks in the period October-December 2004, an investigator recorded how many patients took the stairs and how many took the elevator on the first floor of a hospital close to a diabetes outpatient clinic. A baseline measurement was done over a period of 2 weeks and 4 weeks were used for evaluating the effect of 2 different interventions, each lasting 2 weeks. During the first intervention, a sign was hung up near the elevator, which read: 'Exercise is healthy, take the stairs'. During the second intervention the sign read: 'Use of this elevator is exclusively for personnel and persons with restricted mobility'. Staff members and disabled patients were excluded from the study. A total of 2674 movements were counted. Use of the stairs increased statistically significantly during both interventions: from 54.6% to 63.4% during the first intervention and to 70.4% during the second intervention. Signs in a diabetes outpatient clinic that either encouraged the use of the stairs or discouraged the use of the elevator increased the patients' use of the stairs.

Guidelines for the structural design of experimental multi-purpose VHTR at the elevated temperature services

International Nuclear Information System (INIS)

Nomura, Sueo; Uga, Takeo; Miyamoto, Yoshiaki; Muto, Yasushi; Ikushima, Takeshi

1976-02-01

The guidelines are presented for structural design of the experimental multi-purpose VHTR(Very High Temperature Reactor) at the elevated temperature services. Covered are features of the VHTR structural design, specifications, safety design, seismic design, failure modes to be considered, stress criteria for various load combinations and the mechanical properties of the materials. The guidelines were prepared by referring to safety criteria of high-temperature gas cooled reactors, ASME Boiler and Pressure Vessel code, Section III, case 1592 and the domestic seismic design guide of nuclear power facilities. (auth.)

The structure of hookworm platelet inhibitor (HPI), a CAP superfamily member from Ancylostoma caninum.

Science.gov (United States)

Ma, Dongying; Francischetti, Ivo M B; Ribeiro, Jose M C; Andersen, John F

2015-06-01

Secreted protein components of hookworm species include a number of representatives of the cysteine-rich/antigen 5/pathogenesis-related 1 (CAP) protein family known as Ancylostoma-secreted proteins (ASPs). Some of these have been considered as candidate antigens for the development of vaccines against hookworms. The functions of most CAP superfamily members are poorly understood, but one form, the hookworm platelet inhibitor (HPI), has been isolated as a putative antagonist of the platelet integrins αIIbβ3 and α2β1. Here, the crystal structure of HPI is described and its structural features are examined in relation to its possible function. The HPI structure is similar to those of other ASPs and shows incomplete conservation of the sequence motifs CAP1 and CAP2 that are considered to be diagnostic of CAP superfamily members. The asymmetric unit of the HPI crystal contains a dimer with an extensive interaction interface, but chromatographic measurements indicate that it is primarily monomeric in solution. In the dimeric structure, the putative active-site cleft areas from both monomers are united into a single negatively charged depression. A potential Lys-Gly-Asp disintegrin-like motif was identified in the sequence of HPI, but is not positioned at the apex of a tight turn, making it unlikely that it interacts with the integrin. Recombinant HPI produced in Escherichia coli was found not to inhibit the adhesion of human platelets to collagen or fibrinogen, despite having a native structure as shown by X-ray diffraction. This result corroborates previous analyses of recombinant HPI and suggests that it might require post-translational modification or have a different biological function.

Material Properties Analysis of Structural Members in Pumpkin Balloons

Science.gov (United States)

Sterling, W. J.

2003-01-01

The efficient design, service-life qualification, and reliability predictions for lightweight aerospace structures require careful mechanical properties analysis of candidate structural materials. The demand for high-quality laboratory data is particularly acute when the candidate material or the structural design has little history. The pumpkin-shaped super-pressure balloon presents both challenges. Its design utilizes load members (tendons) extending from apex to base around the gas envelope to achieve a lightweight structure. The candidate tendon material is highly weight-efficient braided HM cord. Previous mechanical properties studies of Zylon have focused on fiber and yarn, and industrial use of the material in tensile applications is limited. For high-performance polymers, a carefully plamed and executed properties analysis scheme is required to ensure the data are relevant to the desired application. Because no directly-applicable testing standard was available, a protocol was developed based on guidelines fiom professional and industry organizations. Due to the liquid-crystalline nature of the polymer, the cord is very stiff, creeps very little, and does not yield. Therefore, the key material property for this application is the breaking strength. The pretension load and gauge length were found to have negligible effect on the measured breaking strength over the ranges investigated. Strain rate was found to have no effect on breaking strength, within the range of rates suggested by the standards organizations. However, at the lower rate more similar to ULDB operations, the strength was reduced. The breaking strength increased when the experiment temperature was decreased from ambient to 183K which is the lowest temperature ULDB is expected to experience. The measured strength under all test conditions was well below that resulting from direct scale-up of fiber strength based on the manufacturers data. This expected result is due to the effects of the

Elevated plasma chemokine CCL18/PARC in beta-thalassemia

NARCIS (Netherlands)

Dimitriou, E.; Verhoek, M.; Altun, S.; Karabatsos, F.; Moraitou, M.; Youssef, J.; Boot, R.; Sarafidou, J.; Karagiorga, M.; Aerts, H.; Michelakakis, H.

2005-01-01

Plasma CCL18/PARC, a member of the CC chemokine family, has been found to be several ten-fold increased in symptomatic Gaucher type I patients. Elevated plasma chitotriosidase levels are a well-known abnormality in Gaucher patients, however, its diagnostic use is limited by the frequent genetic

Materials Delivered by Member States

International Nuclear Information System (INIS)

1975-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to 30 June 1975, in compliance with requests the Agency had made under Article IX. D

Materials Delivered by Member States

International Nuclear Information System (INIS)

1974-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to 31 March 1974, in compliance with requests the Agency had made under Article IX. D

Materials Delivered by Member States

International Nuclear Information System (INIS)

1971-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to the end of 1970, in compliance with requests the Agency had made under Article IX. D

Materials Delivered by Member States

International Nuclear Information System (INIS)

1973-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to the end of 1972, in compliance with requests the Agency had made under Article IX. D

Materials Delivered by Member States

International Nuclear Information System (INIS)

1972-01-01

In this document the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials which Members had delivered up to the end of 1971, in compliance with requests the Agency had made under Article IX. D

Design of Structural Parameters for Centrifugal Elevator Overspeed Governors

Directory of Open Access Journals (Sweden)

Song Yunpu

2014-01-01

Full Text Available As an important part of overspeed and fail-safe protection for elevators, the centrifugal elevator overspeed governor is a device for limiting overspeed of elevator cars. This paper researches on the vibration of the centrifugal block, which plays a key role in the performance of this overspeed governor. By performing dynamics analysis on the centrifugal block, the differential equation on the vibration of the centrifugal block is established. Based on this, the paper performs simulation analysis on the influence of systematic parameters such as the speed of the overspeed governor sheave, the mass of centrifugal block, the turning radius of the centrifugal block, the position where the spring acts, and the stiffness of the centrifugal block spring, on the vibration of the centrifugal block, and finds out their specific influence relationship.

Materials Delivered by Member States

International Nuclear Information System (INIS)

1962-01-01

The information given in this document is divided into two parts. In part I the Director General is reporting to the Members of the Agency, under Article IX. G of the Statute, the quantities of materials delivered up to 30 September 1962 by Member States in compliance with requests the Agency has made under Article IX. D. Part II contains information about materials which have not yet been delivered but which have been allocated, in accordance with Article XI. F. 1 of the Statute, to approved Agency projects for which project agreements were in force on 30 September 1962. Reports on subsequent deliveries of materials and revised information about allocated but undelivered materials will be issued from time to time

Surface Elevation Change of Transantarctic Outlet Glaciers using Historical Aerial Imagery and Structure-from-Motion Photogrammetry

Science.gov (United States)

Child, S. F.; Stearns, L. A.; Girod, L.

2017-12-01

Transantarctic Mountain outlet glaciers drain ice from the East Antarctic Ice Sheet to the Ross Ice Shelf and are generally considered to be stable. However, studies that assess these glaciers typically use data with coarse spatial resolutions (1 - 20 km) and span only the last 15 - 20 years. Here, we use trimetrogon aerial (TMA) photographs collected by the United States Geological Survey from 1960 - 1965 to create historical surface elevation maps. We construct elevations from both the vertical (0° nadir) and oblique photographs using MicMac, a Structure-from-Motion (SfM) software. With typical SfM processing, accurate ground control points (GCPs) are necessary for the best results; however, in situ GCPs are extremely sparse in Antarctica, so we manually identify GCPs using exposed rock outcrops in the WorldView imagery. The historical glacier surface elevations are then compared with present-day elevations derived from WorldView imagery. With this methodology, we assess how Transantarctic outlet glaciers have changed over 55 years. Recent studies indicate thinning of the eastern Ross Ice Shelf, where it borders the Transantarctic Mountains. With long-term records of glacier elevation change, we can differentiate whether ice shelf thinning is driven by changes in glacier or ocean dynamics. These results give us a better understanding of the long-term stability of East Antarctic outlet glaciers, which is essential in improving predictive models of ice sheet behavior.

Study on the influence of Alkali-Silica reaction on structural behavior of reinforced concrete members

International Nuclear Information System (INIS)

Murazumi, Y.; Watanabe, Y.; Matsumoto, N.; Mitsugi, S.; Takiguchi, K.; Masuda, Y.

2005-01-01

Expansion produced by alkali-silica reaction (ASR) has been observed in the turbine generator foundation of the unit 1, Ikata nuclear power station, Japan. The foundation is a reinforced concrete frame structure. This paper, as a part of the series of investigation and experiments, discusses tests on structural behavior of concrete members affected by ASR. The purpose of the study is to obtain experimental results on the effects of ASR on bending and shear behavior of reinforced concrete beams and shear walls, and compare with the calculated results by present evaluation methods for normal concrete structures For the experiments on bending/shear behavior of beam, bending test models with a small amount of rebar and shear test models with larger amount were made of concrete in which ASR was induced by adding alkali or concrete without ASR. It was found from the results that bending strength of the bending test models and shear strength of the shear test models did not fall, nor was it lower than the calculated strength for concrete members without ASR. In the shear wall test, the two test models were made of either concrete with ASR or one without it. Horizontal load was applied with actuators on the test model fixed on the test floor, while vertical load was applied with oil jacks. The results did not indicate that ASR lowered the stiffness or strength of the wall test models, showing the strength was able to be calculated with the same formula for reinforced concrete wall without ASR. (authors)

Monocular Elevation Deficiency - Double Elevator Palsy

Science.gov (United States)

... Español Condiciones Chinese Conditions Monocular Elevation Deficiency/ Double Elevator Palsy En Español Read in Chinese What is monocular elevation deficiency (Double Elevator Palsy)? Monocular Elevation Deficiency, also known by the ...

Elevated temperature effects on concrete properties

International Nuclear Information System (INIS)

Grant, P.R.; Gruber, R.S.; Van Katwijk, C.

1993-08-01

The design of facilities to process or store radioactive wastes presents many challenging engineering problems. Such facilities must not only provide for safe storage of radioactive wastes but they must also be able to maintain confinement of these materials during and after natural phenomena events. Heat generated by the radioactive decay of the wastes will cause the temperature of the concrete containment structure to increase to a magnitude higher than that found in conventional structures. These elevated temperatures will cause strength-related concrete properties to degrade over time. For concrete temperatures less than 150 degree F, no reduction in strength is taken and the provisions of ACI 349, which states that higher temperatures are allowed if tests are provided to evaluate the reduction in concrete strength properties, apply. Methods proposed in a Pacific Northwest Laboratory (PNL) report, Modeling of Time-Variant Concrete Properties at Elevated Temperatures, can be used to evaluate the effects of elevated temperatures on concrete properties. Using these modified concrete properties the capacity of a concrete structure, subjected to elevated temperatures, to resist natural phenomena hazards can be determined

Problems to be solved about inelastic behaviour of materials and inelastic analysis of structures at elevated temperature

International Nuclear Information System (INIS)

Ledermann, P.; Escatha, Y. d'.

1981-01-01

At elevated temperature, ASME CODE CASE N 47 demands, in its design and analysis part to demonstrate that none of eight damages, related to the monotonic and cyclic inelastic behaviour of the material and structure, will happen during the whole life of the reactor. However this demonstration, for strain limits and creep fatigue failure, using a purely elastic analysis as in the ASME CODE Section III, is usually impossible. Inelastic analysis is then necessary. We review some of the research work (theorical and experimental) which is being done to qualify methods for an inelastic analysis of structures at elevated temperature [fr

Remote measurement of canopy reflectance shows the effects of elevated carbon dioxide and ozone on the structure and functioning of soybeans in a field setting.

Science.gov (United States)

Gray, S.; Dermody, O.; Delucia, E.

2006-12-01

By altering physiological processes and modifying canopy structure, elevated atmospheric CO2 and O3 directly and indirectly change the productivity of agroecosystems. Remote sensing of canopy reflectance can be used to monitor physiological and structural changes in an ecosystem over a growing season. To examine effects of changing tropospheric chemistry on water content, chlorophyll content, and changes in leaf area index (LAI), Free-Air Concentration Enrichment (FACE) technology was used to expose large plots of soybean (Glycine max) to elevated atmospheric CO2, elevated O3 (1.5 x ambient), and combined elevated CO2 and O3. The following indices were calculated from weekly measurements of reflectance: water index (WI), photochemical reflectance index (PRI), chlorophyll index, near-infrared/ red (NIR/red), and normalized difference vegetation index (NDVI). NIR/red and LAI were strongly correlated throughout the growth season; however NDVI and LAI were highly correlated only up to LAI of 3. Exposure to elevated CO2 accelerated early-season canopy development and delayed late-season senescence. Growth in elevated O3 had the opposite effect. Additionally, elevated CO2 compensated for negative effects of O3 when the canopy was exposed to both gases simultaneously. Reflectance indices revealed several physiological and structural responses of this agroecosystem to tropospheric change, and ultimately that elevated CO2 and O3 significantly affected this system's productivity and period for carbon gain.

Elevational characteristics of the archaeal community in full-scale activated sludge wastewater treatment plants at a 3,660-meter elevational scale.

Science.gov (United States)

Niu, Lihua; Zhang, Xue; Li, Yi; Wang, Peifang; Zhang, Wenlong; Wang, Chao; Wang, Qing

2017-07-01

Due to the important roles of archaea in wastewater treatment processes, archaeal communities have been studied extensively in various anaerobic reactors, but the knowledge of archaeal communities in full-scale activated sludge wastewater treatment plants (WWTPs) remains quite poor. In this study, 454-pyrosequencing was for the first time employed to investigate archaeal communities from 20 full-scale activated sludge WWTPs distributed at a 3,660-meter elevational scale in China. Results showed that archaeal communities from WWTPs were dominated by Methanosarcinales (84.6%). A core archaeal population (94.5%) composed of Methanosaeta, Methanosarcina, Methanogenium and Methanobrevibacter was shared among WWTPs. The elevational pattern of archaeal communities was observed in WWTPs, with an elevational threshold associated with archaeal community richness and structures at approximately 1,500 meters above sea level (masl). A declining trend in community richness with increasing elevation was observed at higher elevations, whereas no trend was presented at lower elevations. Spearman correlation analysis indicated that the archaeal community richness at higher elevations was associated with more environmental variables than that at lower elevations. Redundancy analysis indicated that wastewater variables were the dominant contributors to the variation of community structures at higher elevations, followed by operational variables and elevation.

Community and ecosystem responses to elevational gradients

DEFF Research Database (Denmark)

Sundqvist, Maja K.; Sanders, Nate; Wardle, David A.

2013-01-01

Community structure and ecosystem processes often vary along elevational gradients. Their responses to elevation are commonly driven by changes in temperature, and many community- and ecosystem-level variables therefore frequently respond similarly to elevation across contrasting gradients...... elevational gradients for understanding community and ecosystem responses to global climate change at much larger spatial and temporal scales than is possible through conventional ecological experiments. However, future studies that integrate elevational gradient approaches with experimental manipulations...... will provide powerful information that can improve predictions of climate change impacts within and across ecosystems....

Space Station tethered elevator system

Science.gov (United States)

Haddock, Michael H.; Anderson, Loren A.; Hosterman, K.; Decresie, E.; Miranda, P.; Hamilton, R.

1989-01-01

The optimized conceptual engineering design of a space station tethered elevator is presented. The tethered elevator is an unmanned, mobile structure which operates on a ten-kilometer tether spanning the distance between Space Station Freedom and a platform. Its capabilities include providing access to residual gravity levels, remote servicing, and transportation to any point along a tether. The report discusses the potential uses, parameters, and evolution of the spacecraft design. Emphasis is placed on the elevator's structural configuration and three major subsystem designs. First, the design of elevator robotics used to aid in elevator operations and tethered experimentation is presented. Second, the design of drive mechanisms used to propel the vehicle is discussed. Third, the design of an onboard self-sufficient power generation and transmission system is addressed.

Visualizing multistep elevator-like transitions of a nucleoside transporter.

Science.gov (United States)

Hirschi, Marscha; Johnson, Zachary Lee; Lee, Seok-Yong

2017-05-04

Membrane transporters move substrates across the membrane by alternating access of their binding sites between the opposite sides of the membrane. An emerging model of this process is the elevator mechanism, in which a substrate-binding transport domain moves a large distance across the membrane. This mechanism has been characterized by a transition between two states, but the conformational path that leads to the transition is not yet known, largely because the available structural information has been limited to the two end states. Here we present crystal structures of the inward-facing, intermediate, and outward-facing states of a concentrative nucleoside transporter from Neisseria wadsworthii. Notably, we determined the structures of multiple intermediate conformations, in which the transport domain is captured halfway through its elevator motion. Our structures present a trajectory of the conformational transition in the elevator model, revealing multiple intermediate steps and state-dependent conformational changes within the transport domain that are associated with the elevator-like motion.

Space Elevator Concept Considered a Reality

Science.gov (United States)

2000-01-01

The `once upon a time' science fiction concept of a space elevator has been envisioned and studied as a real mass transportation system in the latter part of the 21st century. David Smitherman of NASA's Marshall Space Flight Center's Advanced Projects Office has compiled plans for such an elevator. The space elevator concept is a structure extending from the surface of the Earth to geostationary Earth orbit (GEO) at 35,786 km in altitude. The tower would be approximately 50 km tall with a cable tethered to the top. Its center mass would be at GEO such that the entire structure orbits the Earth in sync with the Earth's rotation maintaining a stationary position over its base attachment at the equator. Electromagnetic vehicles traveling along the cable could serve as a mass transportation system for transporting people, payloads, and power between space and Earth. This illustration by artist Pat Rawling shows the concept of a space elevator as viewed from the geostationary transfer station looking down the length of the elevator towards the Earth.

STRAP-2, Stress Analysis of Structure with Static Loading by Finite Elements Method. STRAP-D, Stress Analysis of Structure with Time-Dependent Loading by Finite Elements Method

International Nuclear Information System (INIS)

Dearien, J.A.; Uldrich, E.D.

1975-01-01

1 - Description of problem or function: The code STRAP (Structural Analysis Package) was developed to analyze the response of structural systems to static and dynamic loading conditions. STRAP-S solves for the displacements and member forces of structural systems under static loads and temperature gradients. STRAP-D will solve numerically a given structural dynamics problem. 2 - Method of solution: STRAP-S generates the stiffness matrix of a structure by the finite element method and solves the resulting equations for structural displacements and member forces. STRAP-D generates the stiffness matrix, solves for eigenvalues and eigenvectors, uncouples and solves the series of second-order ordinary differential equations, and then calculates and plots the requested member forces. 3 - Restrictions on the complexity of the problem: STRAP-S maxima: 250 degrees of freedom, 100 members; STRAP-D maxima: 100 degrees of freedom, 80 time-steps in the forcing function input

On elevated fluoride and boron concentrations in groundwaters associated with the Lake Saint-Martin impact structure, Manitoba

International Nuclear Information System (INIS)

Desbarats, Alexandre J.

2009-01-01

Hydrogeological investigations conducted by the Geological Survey of Canada in the Lake Saint-Martin region of Manitoba have confirmed earlier reports of naturally elevated F - and B concentrations in local groundwaters. Fluoride and B concentrations are highly correlated (r 2 = 0.905) and reach 15.1 mg/L and 8.5 mg/L, respectively. Virtually all groundwaters with F - concentrations greater than the drinking water limit of 1.5 mg/L are from wells within the Lake Saint-Martin impact structure, a 208 Ma complex crater 23 km in diameter underlying a large part of the study area. The high-F - groundwaters can be classified into two groups according to their anionic and isotopic compositions. Group I samples consist of Na-mixed anion groundwaters, with Cl greater than 100 mg/L and highly depleted 18 O compositions indicative of recharge under much cooler climatic conditions than at present. Samples belonging to this group exhibit a striking relationship to crater morphology, and are found in an arcuate belt within the southern rim of the impact structure. Group II high-F - samples consist of Na-HCO 3 -SO 4 groundwaters, with little Cl, and less depleted 18 O compositions. Samples belonging to this group are associated with groundwaters recharged locally, on a low ridge within the impact structure. This paper traces the probable source of high-F - groundwaters to phosphatic pellets in shales of the Winnipeg Formation, a regional basal clastic unit which sub-crops at shallow depth beneath the crater rim as a result of more than 200 m of structural uplift associated with the impact event. This extensive aquifer is known elsewhere in southern Manitoba for its naturally-softened groundwaters and locally elevated F - concentrations. Group I groundwaters are interpreted as discharge from the Winnipeg Formation where it abuts against crater-fill deposits. Group II high-F - groundwaters are interpreted as modern recharge from within the impact structure, displacing Group I

Novel development of the micro-tensile test at elevated temperature using a test structure with integrated micro-heater

Science.gov (United States)

Ang, W. C.; Kropelnicki, P.; Soe, Oak; Ling, J. H. L.; Randles, A. B.; Hum, A. J. W.; Tsai, J. M. L.; Tay, A. A. O.; Leong, K. C.; Tan, C. S.

2012-08-01

This paper describes the novel development of a micro-tensile testing method that allows testing at elevated temperatures. Instead of using a furnace, a titanium/platinum thin film micro-heater was fabricated on a conventional dog-bone-shaped test structure to heat up its gauge section locally. An infrared (IR) camera with 5 µm resolution was employed to verify the temperature uniformity across the gauge section of the test structure. With this micro-heater-integrated test structure, micro-tensile tests can be performed at elevated temperatures using any conventional tensile testing system without any major modification to the system. In this study, the tensile test of the single crystal silicon (SCS) thin film with (1 0 0) surface orientation and tensile direction was performed at room temperature and elevated temperatures, up to 300 °C. Experimental results for Young's modulus as a function of temperature are presented. A micro-sized SCS film showed a low dependence of mechanical properties on temperature up to 300 °C.

Understanding Heterogeneous Preferences of Cooperative Members

NARCIS (Netherlands)

Kalogeras, N.; Pennings, J.M.E.; Lans, van der I.A.; Garcia, P.; Dijk, van G.

2009-01-01

We study the heterogeneity in the preference structure of cooperative members. Using conjoint analysis the utility that members attach to intra-organizational and strategic attributes of their cooperative is elicited. Recognizing that members are not homogenous, a concomitant finitemixture

Unusual head and neck injury in elevator: autopsy study.

Science.gov (United States)

Eren, B; Türkmen, N; Dokgöz, H

2012-10-01

Industrial injuries related to auto-load-carrying vehicles were not frequently reported in the literature. Presented case was, 31-year-old male furniture worker. Deceased was found in awkward position in furniture workshop. Victim was observed on his knees in front of the elevator, head and neck lodged within openings of the elevator, and head and neck structures compressed-guillotined by the lower platform of the elevator were detected. We presented rare case of head and neck compression by elevator. Key words: head - neck - accidents - elevator - autopsy.

Resilience of the prokaryotic microbial community of Acropora digitifera to elevated temperature.

Science.gov (United States)

Gajigan, Andrian P; Diaz, Leomir A; Conaco, Cecilia

2017-08-01

The coral is a holobiont formed by the close interaction between the coral animal and a diverse community of microorganisms, including dinoflagellates, bacteria, archaea, fungi, and viruses. The prokaryotic symbionts of corals are important for host fitness but are also highly sensitive to changes in the environment. In this study, we used 16S ribosomal RNA (rRNA) sequencing to examine the response of the microbial community associated with the coral, Acropora digitifera, to elevated temperature. The A. digitifera microbial community is dominated by operational taxonomic unit (OTUs) affiliated with classes Alphaproteobacteria and Gammaproteobacteria. The prokaryotic community in the coral tissue is distinct from that of the mucus and the surrounding seawater. Remarkably, the overall microbial community structure of A. digitifera remained stable for 10 days of continuous exptosure at 32°C compared to corals maintained at 27°C. However, the elevated temperature regime resulted in a decrease in the abundance of OTUs affiliated with certain groups of bacteria, such as order Rhodobacterales. On the other hand, some OTUs affiliated with the orders Alteromonadales, Vibrionales, and Flavobacteriales, which are often associated with diseased and stressed corals, increased in abundance. Thus, while the A. digitifera bacterial community structure appears resilient to higher temperature, prolonged exposure and intensified stress results in changes in the abundance of specific microbial community members that may affect the overall metabolic state and health of the coral holobiont. © 2017 The Authors. MicrobiologyOpen published by John Wiley & Sons Ltd.

Direct visualization of glutamate transporter elevator mechanism by high-speed AFM.

Science.gov (United States)

Ruan, Yi; Miyagi, Atsushi; Wang, Xiaoyu; Chami, Mohamed; Boudker, Olga; Scheuring, Simon

2017-02-14

Glutamate transporters are essential for recovery of the neurotransmitter glutamate from the synaptic cleft. Crystal structures in the outward- and inward-facing conformations of a glutamate transporter homolog from archaebacterium Pyrococcus horikoshii , sodium/aspartate symporter Glt Ph , suggested the molecular basis of the transporter cycle. However, dynamic studies of the transport mechanism have been sparse and indirect. Here we present high-speed atomic force microscopy (HS-AFM) observations of membrane-reconstituted Glt Ph at work. HS-AFM movies provide unprecedented real-space and real-time visualization of the transport dynamics. Our results show transport mediated by large amplitude 1.85-nm "elevator" movements of the transport domains consistent with previous crystallographic and spectroscopic studies. Elevator dynamics occur in the absence and presence of sodium ions and aspartate, but stall in sodium alone, providing a direct visualization of the ion and substrate symport mechanism. We show unambiguously that individual protomers within the trimeric transporter function fully independently.

Nurses' participation in personal knowledge transfer: the role of leader-member exchange (LMX) and structural empowerment.

Science.gov (United States)

Davies, Alicia; Wong, Carol A; Laschinger, Heather

2011-07-01

The purpose of this study was to test Kanter's theory by examining relationships among structural empowerment, leader-member exchange (LMX) quality and nurses' participation in personal knowledge transfer activities. Despite the current emphasis on evidence-based practice in health care, research suggests that implementation of research findings in everyday clinical practice is unsystematic at best with mixed outcomes. This study was a secondary analysis of data collected using a non-experimental, predictive mailed survey design. A random sample of 400 registered nurses who worked in urban tertiary care hospitals in Ontario yielded a final sample of 234 for a 58.5% response rate. Hierarchical multiple linear regression analysis revealed that the combination of LMX and structural empowerment accounted for 9.1% of the variance in personal knowledge transfer but only total empowerment was a significant independent predictor of knowledge transfer (β=0.291, t=4.012, Pleader-member exchange quality resulted in increased participation in personal knowledge transfer in practice. The results reinforce the pivotal role of nurse managers in supporting empowering work environments that are conducive to transfer of knowledge in practice to provide evidence-based care. © 2011 The Authors. Journal compilation © 2011 Blackwell Publishing Ltd.

Sensitivity of metrics of phylogenetic structure to scale, source of data and species pool of hummingbird assemblages along elevational gradients.

Directory of Open Access Journals (Sweden)

Sebastián González-Caro

Full Text Available Patterns of phylogenetic structure of assemblages are increasingly used to gain insight into the ecological and evolutionary processes involved in the assembly of co-occurring species. Metrics of phylogenetic structure can be sensitive to scaling issues and data availability. Here we empirically assess the sensitivity of four metrics of phylogenetic structure of assemblages to changes in (i the source of data, (ii the spatial grain at which assemblages are defined, and (iii the definition of species pools using hummingbird (Trochilidae assemblages along an elevational gradient in Colombia. We also discuss some of the implications in terms of the potential mechanisms driving these patterns. To explore how source of data influence phylogenetic structure we defined assemblages using three sources of data: field inventories, museum specimens, and range maps. Assemblages were defined at two spatial grains: coarse-grained (elevational bands of 800-m width and fine-grained (1-km(2 plots. We used three different species pools: all species contained in assemblages, all species within half-degree quadrats, and all species either above or below 2000 m elevation. Metrics considering phylogenetic relationships among all species within assemblages showed phylogenetic clustering at high elevations and phylogenetic evenness in the lowlands, whereas those metrics considering only the closest co-occurring relatives showed the opposite trend. This result suggests that using multiple metrics of phylogenetic structure should provide greater insight into the mechanisms shaping assemblage structure. The source and spatial grain of data had important influences on estimates of both richness and phylogenetic structure. Metrics considering the co-occurrence of close relatives were particularly sensitive to changes in the spatial grain. Assemblages based on range maps included more species and showed less phylogenetic structure than assemblages based on museum or field

Effects of elevated CO2 concentration on growth, annual ring structure and photosynthesis in Larix kaempferi seedlings

International Nuclear Information System (INIS)

Yazaki, K.; Ishida, S.; Kawagishi, T.; Fukatsu, E.; Funada, R.; Maruyama, Y.; Kitao, M.; Tobita, H.; Koike, T.

2004-01-01

The effects of elevated carbon dioxide concentration and two nutrient regimes on stem growth rate, annual ring structure and temporal variations in photosynthetic characteristics of seedlings of Japanese larch were evaluated. When compared with ambient carbon dioxide, elevated carbon dioxide reduced stem height and increased stem basal diameter, but had no significant effect on ring width or the number of tracheids per radial file. No obvious difference was observed in cell wall thickness or the relative area of cell wall between seedlings grown in ambient or elevated carbon dioxide. Net assimilation rate increased in the presence of elevated carbon dioxide, however, the increase in whole-crown photosynthetic rate was minimal due to the smaller needle area and acclimation of the photosynthetic characteristics of the needles to the growth in carbon dioxide concentration. Conclusion: elevated carbon dioxide concentration did not appear to significantly affect the capacity of stems of Japanese larch seedlings for carbon fixation for use in cell wall synthesis, although there was evidence of change in the temporal pattern of stem growth and stem thickening. 52 refs., 3 tabs., 4 figs

Three family members with elevated plasma cobalamin, transcobalamin and soluble transcobalamin receptor (sCD320)

DEFF Research Database (Denmark)

Hoffmann-Lücke, Elke; Arendt, Johan F B; Nissen, Peter H

2013-01-01

deficiency were found. DNA sequencing of the TCN2 gene revealed several known polymorphisms not associated with highly elevated transcobalamin levels. Upon gel filtration, sCD320 eluted as a larger molecule than previously reported. By incubation with anti-transcobalamin antibodies, we precipitated both...... transcobalamin and part of sCD320. CONCLUSIONS: The high cobalamin levels were mainly explained by high levels of holoTC, possibly caused by complex formation with its soluble receptor, sCD320. The family occurrence points to a genetic explanation....

[The role of university hospital executive board members].

Science.gov (United States)

Debatin, J F; Rehr, J

2009-09-01

Demographic changes and medical progress in combination with vastly altered regulatory and economic environments have forced considerable change in the structure of German university hospitals in recent years. These changes have affected medical care as well as research and medical school training. To allow for more flexibility and a higher level of reactivity to the changing environment German university hospitals were transferred from state agencies to independent corporate structures. All but one remains wholly owned by the respective state governments. The governing structure of these independent medical hospitals consists of an executive board, generally made up of a medical director, a financial director, a director for nursing, and the dean of the medical faculty. In most hospitals, the medical director serves as chief executive officer. The regulations governing the composition and responsibility of the members of the executive board differ from state to state. These differences do affect to some degree the interactive effectiveness of the members of the executive boards. Modalities that stress the overall responsibility for all board members seem to work better than those that define clear portfolio limits. Even more than organizational and regulatory differences, the effectiveness of the work of the executive boards is influenced by the personality of the board members themselves. Success appears to be a clear function of the willingness of all members to work together.

Military service absences and family members' mental health: A timeline followback assessment.

Science.gov (United States)

Rodriguez, Aubrey J; Margolin, Gayla

2015-08-01

Although military service, and particularly absence due to deployment, has been linked to risk for depression and anxiety among some spouses and children of active duty service members, there is limited research to explain the heterogeneity in family members' reactions to military service stressors. The current investigation introduces the Timeline Followback Military Family Interview (TFMFI) as a clinically useful strategy to collect detailed time-linked information about the service member's absences. Two dimensions of parent absence--the extent to which absences coincide with important family events and cumulative time absent--were tested as potential risks to family members' mental health. Data from 70 mother-adolescent pairs revealed that the number of important family events missed by the service member was linked to elevated youth symptoms of depression, even when accounting for the number of deployments and cumulative duration of the service member's absence. However, youth who reported more frequent contact with the service member during absences were buffered from the effects of extensive absence. Mothers' symptoms were associated with the cumulative duration of the service members' time away, but not with family events missed by the service member. These results identify circumstances that increase the risk for mental health symptoms associated with military family life. The TFMFI provides an interview-based strategy for clinicians wishing to understand military family members' lived experience during periods of service-member absence. (c) 2015 APA, all rights reserved).

Stair-Step Pattern of Soil Bacterial Diversity Mainly Driven by pH and Vegetation Types Along the Elevational Gradients of Gongga Mountain, China.

Science.gov (United States)

Li, Jiabao; Shen, Zehao; Li, Chaonan; Kou, Yongping; Wang, Yansu; Tu, Bo; Zhang, Shiheng; Li, Xiangzhen

2018-01-01

Ecological understandings of soil bacterial community succession and assembly mechanism along elevational gradients in mountains remain not well understood. Here, by employing the high-throughput sequencing technique, we systematically examined soil bacterial diversity patterns, the driving factors, and community assembly mechanisms along the elevational gradients of 1800-4100 m on Gongga Mountain in China. Soil bacterial diversity showed an extraordinary stair-step pattern along the elevational gradients. There was an abrupt decrease of bacterial diversity between 2600 and 2800 m, while no significant change at either lower (1800-2600 m) or higher (2800-4100 m) elevations, which coincided with the variation in soil pH. In addition, the community structure differed significantly between the lower and higher elevations, which could be primarily attributed to shifts in soil pH and vegetation types. Although there was no direct effect of MAP and MAT on bacterial community structure, our partial least squares path modeling analysis indicated that bacterial communities were indirectly influenced by climate via the effect on vegetation and the derived effect on soil properties. As for bacterial community assembly mechanisms, the null model analysis suggested that environmental filtering played an overwhelming role in the assembly of bacterial communities in this region. In addition, variation partition analysis indicated that, at lower elevations, environmental attributes explained much larger fraction of the β-deviation than spatial attributes, while spatial attributes increased their contributions at higher elevations. Our results highlight the importance of environmental filtering, as well as elevation-related spatial attributes in structuring soil bacterial communities in mountain ecosystems.

National requirements for improved elevation data

Science.gov (United States)

Snyder, Gregory I.; Sugarbaker, Larry J.; Jason, Allyson L.; Maune, David F.

2014-01-01

This report presents the results of surveys, structured interviews, and workshops conducted to identify key national requirements for improved elevation data for the United States and its territories, including coastlines. Organizations also identified and reported the expected economic benefits that would be realized if their requirements for improved elevation were met (appendixes 1–3). This report describes the data collection methodology and summarizes the findings. Participating organizations included 34 Federal agencies, 50 States and two territories, and a sampling of local governments, tribes, and nongovernmental orgnizations. The nongovernmental organizations included The Nature Conservancy and a sampling of private sector businesses. These data were collected in 2010-2011 as part of the National Enhanced Elevation Assessment (NEEA), a study to identify program alternatives for better meeting the Nation’s elevation data needs. NEEA tasks included the collection of national elevation requirements; analysis of the benefits and costs of meeting these requirements; assessment of emerging elevation technologies, lifecycle data management needs, and costs for managing and distributing a national-scale dataset and derived products; and candidate national elevation program alternatives that balance costs and benefits in meeting the Nation’s elevation requirements. The NEEA was sponsored by the National Digital Elevation Program (NDEP), a government coordination body with the U.S. Geological Survey (USGS) as managing partner that includes the National Geospatial-Intelligence Agency (NGA), the Federal Emergency Management Agency (FEMA), the Natural Resources Conservation Service (NRCS), the U.S. Army Corps of Engineers (USACE), and the National Oceanic and Atmospheric Administration (NOAA), among the more than a dozen agencies and organizations. The term enhanced elevation data as used in this report refers broadly to three-dimensional measurements of land or

Sandwich-structured polymer nanocomposites with high energy density and great charge–discharge efficiency at elevated temperatures

Science.gov (United States)

Li, Qi; Liu, Feihua; Yang, Tiannan; Gadinski, Matthew R.; Zhang, Guangzu; Chen, Long-Qing; Wang, Qing

2016-01-01

The demand for a new generation of high-temperature dielectric materials toward capacitive energy storage has been driven by the rise of high-power applications such as electric vehicles, aircraft, and pulsed power systems where the power electronics are exposed to elevated temperatures. Polymer dielectrics are characterized by being lightweight, and their scalability, mechanical flexibility, high dielectric strength, and great reliability, but they are limited to relatively low operating temperatures. The existing polymer nanocomposite-based dielectrics with a limited energy density at high temperatures also present a major barrier to achieving significant reductions in size and weight of energy devices. Here we report the sandwich structures as an efficient route to high-temperature dielectric polymer nanocomposites that simultaneously possess high dielectric constant and low dielectric loss. In contrast to the conventional single-layer configuration, the rationally designed sandwich-structured polymer nanocomposites are capable of integrating the complementary properties of spatially organized multicomponents in a synergistic fashion to raise dielectric constant, and subsequently greatly improve discharged energy densities while retaining low loss and high charge–discharge efficiency at elevated temperatures. At 150 °C and 200 MV m−1, an operating condition toward electric vehicle applications, the sandwich-structured polymer nanocomposites outperform the state-of-the-art polymer-based dielectrics in terms of energy density, power density, charge–discharge efficiency, and cyclability. The excellent dielectric and capacitive properties of the polymer nanocomposites may pave a way for widespread applications in modern electronics and power modules where harsh operating conditions are present. PMID:27551101

Study of tertiary creep instability in several elevated-temperature structural materials

International Nuclear Information System (INIS)

Booker, M.K.; Sikka, V.K.

1978-01-01

Data for a number of common elevated temperature structural materials have been analyzed to yield mathematical predictions for the time and strain to tertiary creep at various rupture lives and temperatures. Materials examined include types 304 and 316 stainless steel, 2 1/4 Cr-1 Mo steel, alloy 800H, alloy 718, Hastelloy alloy X, and ERNiCr--3 weld metal. Data were typically examined over a range of creep temperatures for rupture lives ranging from less than 100 to greater than 10,000 hours. Within a given material, trends in these quantities can be consistently described, but it is difficult to directly relate the onset of tertiary creep to failure-inducing instabilities. A series of discontinued tests for alloy 718 at 649 and 620 0 C showed that the material fails by intergranular cracking but that no significant intergranular cracking occurs until well after the onset of tertiary creep

Short-term responses and resistance of soil microbial community structure to elevated CO2 and N addition in grassland mesocosms.

Science.gov (United States)

Simonin, Marie; Nunan, Naoise; Bloor, Juliette M G; Pouteau, Valérie; Niboyet, Audrey

2017-05-01

Nitrogen (N) addition is known to affect soil microbial communities, but the interactive effects of N addition with other drivers of global change remain unclear. The impacts of multiple global changes on the structure of microbial communities may be mediated by specific microbial groups with different life-history strategies. Here, we investigated the combined effects of elevated CO2 and N addition on soil microbial communities using PLFA profiling in a short-term grassland mesocosm experiment. We also examined the linkages between the relative abundance of r- and K-strategist microorganisms and resistance of the microbial community structure to experimental treatments. N addition had a significant effect on microbial community structure, likely driven by concurrent increases in plant biomass and in soil labile C and N. In contrast, microbial community structure did not change under elevated CO2 or show significant CO2 × N interactions. Resistance of soil microbial community structure decreased with increasing fungal/bacterial ratio, but showed a positive relationship with the Gram-positive/Gram-negative bacterial ratio. Our findings suggest that the Gram-positive/Gram-negative bacteria ratio may be a useful indicator of microbial community resistance and that K-strategist abundance may play a role in the short-term stability of microbial communities under global change. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Structural phase transition in a growing network model with tunable member intimacy

Science.gov (United States)

Kim, Kibum; Jo, Woo Seong; Kim, Beom Jun

2017-05-01

Users of online communities become more intimate in time by writing posts and exchanging comments to each other. Although a certain level of intimacy among a group of members can be beneficial for the activity of the whole community, too strong intimacy among existing members can make newcomers feel alienated, driving them to leave the community. In this letter, we introduce a growing network model in which we systematically study the effect of member intimacy on the formation of connected component of the network. We introduce a parameter called clinginess and control how the member intimacy affects the communication activity. We observe that cumulative number of users who leave the community exhibits a transition-like behavior, similarly to the discontinuous transition in statistical mechanics models. Implication of our result in constructing a sustainable online community is also discussed.

Effect of elevated CO2 on monoterpene emission of young Quercus ilex trees and its relation to structural and ecophysiological parameters

International Nuclear Information System (INIS)

Staudt, M.; Joffre, R.; Rambal, S.; Kesselmeier, J.

2001-01-01

Growth, leaf monoterpene emission, gas exchange, leaf structure and leaf chemical composition of one year-old oak seedlings grown in ambient and elevated carbon dioxide concentrations were investigated. Results of the various measurements and experiments are discussed in the context of resource acquisition and allocation by oak seedlings, and evaluated in terms of emission predictions. From the findings it was concluded that oak seedlings grown in elevated carbon dioxide have an increased emission capacity and increased foliage biomass. It was predicted that in a future world, characterized by high carbon dioxide concentrations, the atmospheric load of monoterpenes from Mediterranean forests will rise, although mature trees native to environments with elevated carbon dioxide will likely respond differently than the oak seedlings used in this study. The impacts of climatic change are uncertain, but it is suspected that trees grown near carbon dioxide springs benefit from increased resistance to water stress. There are indications that the increased capacity to tolerate water limitations in response to growth in elevated carbon dioxide environments could indirectly promote emissions. 39 refs., 4 tabs., 1 fig

Nitrogen-mediated effects of elevated CO2 on intra-aggregate soil pore structure.

Science.gov (United States)

Caplan, Joshua S; Giménez, Daniel; Subroy, Vandana; Heck, Richard J; Prior, Stephen A; Runion, G Brett; Torbert, H Allen

2017-04-01

Soil pore structure has a strong influence on water retention, and is itself influenced by plant and microbial dynamics such as root proliferation and microbial exudation. Although increased nitrogen (N) availability and elevated atmospheric CO 2 concentrations (eCO 2 ) often have interacting effects on root and microbial dynamics, it is unclear whether these biotic effects can translate into altered soil pore structure and water retention. This study was based on a long-term experiment (7 yr at the time of sampling) in which a C 4 pasture grass (Paspalum notatum) was grown on a sandy loam soil while provided factorial additions of N and CO 2 . Through an analysis of soil aggregate fractal properties supported by 3D microtomographic imagery, we found that N fertilization induced an increase in intra-aggregate porosity and a simultaneous shift toward greater accumulation of pore space in larger aggregates. These effects were enhanced by eCO 2 and yielded an increase in water retention at pressure potentials near the wilting point of plants. However, eCO 2 alone induced changes in the opposite direction, with larger aggregates containing less pore space than under control conditions, and water retention decreasing accordingly. Results on biotic factors further suggested that organic matter gains or losses induced the observed structural changes. Based on our results, we postulate that the pore structure of many mineral soils could undergo N-dependent changes as atmospheric CO 2 concentrations rise, having global-scale implications for water balance, carbon storage, and related rhizosphere functions. © 2016 John Wiley & Sons Ltd.

Aerospace structural design process improvement using systematic evolutionary structural modeling

Science.gov (United States)

Taylor, Robert Michael

2000-10-01

A multidisciplinary team tasked with an aircraft design problem must understand the problem requirements and metrics to produce a successful design. This understanding entails not only knowledge of what these requirements and metrics are, but also how they interact, which are most important (to the customer as well as to aircraft performance), and who in the organization can provide pertinent knowledge for each. In recent years, product development researchers and organizations have developed and successfully applied a variety of tools such as Quality Function Deployment (QFD) to coordinate multidisciplinary team members. The effectiveness of these methods, however, depends on the quality and fidelity of the information that team members can input. In conceptual aircraft design, structural information is of lower quality compared to aerodynamics or performance because it is based on experience rather than theory. This dissertation shows how advanced structural design tools can be used in a multidisciplinary team setting to improve structural information generation and communication through a systematic evolution of structural detail. When applied to conceptual design, finite element-based structural design tools elevate structural information to the same level as other computationally supported disciplines. This improved ability to generate and communicate structural information enables a design team to better identify and meet structural design requirements, consider producibility issues earlier, and evaluate structural concepts. A design process experiment of a wing structural layout in collaboration with an industrial partner illustrates and validates the approach.

Molecular Simulation and Biochemical Studies Support an Elevator-type Transport Mechanism in EIIC.

Science.gov (United States)

Lee, Jumin; Ren, Zhenning; Zhou, Ming; Im, Wonpil

2017-06-06

Enzyme IIC (EIIC) is a membrane-embedded sugar transport protein that is part of the phosphoenolpyruvate-dependent phosphotransferases. Crystal structures of two members of the glucose EIIC superfamily, bcChbC in the inward-facing conformation and bcMalT in the outward-facing conformation, were previously solved. Comparing the two structures led us to the hypothesis that sugar translocation could be achieved by an elevator-type transport mechanism in which a transport domain binds to the substrate and, through rigid body motions, transports it across the membrane. To test this hypothesis and to obtain more accurate descriptions of alternate conformations of the two proteins, we first performed collective variable-based steered molecular dynamics (CVSMD) simulations starting with the two crystal structures embedded in model lipid bilayers, and steered their transport domain toward their own alternative conformation. Our simulations show that large rigid-body motions of the transport domain (55° in rotation and 8 Å in translation) lead to access of the substrate binding site to the alternate side of the membrane. H-bonding interactions between the sugar and the protein are intact, although the side chains of the binding-site residues were not restrained in the simulation. Pairs of residues in bcMalT that are far apart in the crystal structure become close to each other in the simulated model. Some of these pairs can be cross-linked by a mercury ion when mutated to cysteines, providing further support for the CVSMD-generated model. In addition, bcMalT binds to maltose with similar affinities before and after the cross-linking, suggesting that the binding site is preserved after the conformational change. In combination, these results support an elevator-type transport mechanism in EIIC. Copyright © 2017 Biophysical Society. Published by Elsevier Inc. All rights reserved.

High-speed elevators controlled by inverters

Energy Technology Data Exchange (ETDEWEB)

Sakai, Yoshio; Takahashi, Hideaki; Nakamura, Kiyoshi; Kinoshita, Hiroshi

1988-10-25

The super-high-speed elevator with superiority to 300m/min of speed, requires both the large capacity power and wide range speed controls. Therefore, in order to materialize the smooth and quiet operation characteristics, by applying the inverter control, the low torque ripple control in the low frequency range and high frequency large capacity inverting for lowering the motor in noise are necessary with their being assured of reliability. To satisfy the above necessary items, together with the development of a sine wave pulse width and frequency modulation (PWM/PFM) control system, to more precisely enable the sine wave electric current control, and 3kHz switching power converter, using a 800A power transistor module, a supervoltage control circuit under the extraordinary condition was designed. As a result of commercializing a 360m/min super-high speed inverter elevator, the power source unit, due to the effect of high power factor, could be reduced by 30% in capacity and also the higher harmonic wave including ratio could be considerably lowered to the inferiority to 5%. 2 references, 7 figures, 1 table.

An Automatic System for Elevator Monitoring

OpenAIRE

Md. Haidar Sharif; Ibrahim Furkan Ince

2015-01-01

An elevator is a conveyor device or transport equipment that moves people or goods between floors or levels or decks of a building, vessel, or other structures. It has become a part and parcel of modern life in developed countries. The number of floors in high buildings, skyscrapers, and towers generate the usage of elevators. If it is simply assumed that each floor has at least two elevators in a thirty-floor building, people call the elevators in each floor even they are already occupied in...

The elevation and its distribution in geomorphological regions of the European Russia

Science.gov (United States)

Kharchenko, S. V.; Ermolaev, O. P.; Mukharamova, S. S.

2018-01-01

Spatial differences of elevation were analysed by side of view of geomorphological boundaries on the European Russia territory. Geomorphological pattern of the studied territory was taken from Geomorphological Map of the USSR at scale of 1: 2 500 000. There 2401 fragments for combinations of 58 types of structural landforms and 22 types of sculptural landforms were allocated. The elevation values computed by digital elevation model (cell size - 200 m, number of cells - 322M) based on SRTM (south of 60 nl.) and GDEM 2010 (north of 60 nl.) resampled data. It was founded that some types of structural (16 types) and sculptural (6 types) landforms located in the relatively thin intervals of elevation. Using of elevation above sea level is needed for effective automatic recognizing these landform regions.

Spring leaf flush in aspen (Populus tremuloides) clones is altered by long-term growth at elevated carbon dioxide and elevated ozone concentration

International Nuclear Information System (INIS)

McGrath, Justin M.; Karnosky, David F.; Ainsworth, Elizabeth A.

2010-01-01

Early spring leaf out is important to the success of deciduous trees competing for light and space in dense forest plantation canopies. In this study, we investigated spring leaf flush and how long-term growth at elevated carbon dioxide concentration ([CO 2 ]) and elevated ozone concentration ([O 3 ]) altered leaf area index development in a closed Populus tremuloides (aspen) canopy. This work was done at the Aspen FACE experiment where aspen clones have been grown since 1997 in conditions simulating the [CO 2 ] and [O 3 ] predicted for ∼2050. The responses of two clones were compared during the first month of spring leaf out when CO 2 fumigation had begun, but O 3 fumigation had not. Trees in elevated [CO 2 ] plots showed a stimulation of leaf area index (36%), while trees in elevated [O 3 ] plots had lower leaf area index (-20%). While individual leaf area was not significantly affected by elevated [CO 2 ], the photosynthetic operating efficiency of aspen leaves was significantly improved (51%). There were no significant differences in the way that the two aspen clones responded to elevated [CO 2 ]; however, the two clones responded differently to long-term growth at elevated [O 3 ]. The O 3 -sensitive clone, 42E, had reduced individual leaf area when grown at elevated [O 3 ] (-32%), while the tolerant clone, 216, had larger mature leaf area at elevated [O 3 ] (46%). These results indicate a clear difference between the two clones in their long-term response to elevated [O 3 ], which could affect competition between the clones, and result in altered genotypic composition in future atmospheric conditions. - Spring leaf flush is stimulated by elevated [CO 2 ] and suppressed by elevated [O 3 ] in aspen (Populus tremuloides).

High-speed elevator ELEXCIA{sub TM}; Kosoku elevator EXEXCIA{sub TM}

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

New series high-speed elevator ELEXCIA{sub TM} was put on sale in November 1999. In ELEXCIA{sub TM}, the car and door as well as the newly developed hoist and control device were improved in compactness, lightweight, silence, and riding quality. The major features of the high-speed elevator are as follows: (1) The use of an outer rotor-type permanent magnetic synchronous motor (PMSM) in a hoist reduced the mass of the hoist (by about 40% as compared with the conventional one). (2) The use of a double-structured car side plate and floor enabled a silent car. (3) Improved door performance. The introduction of a PMSM motor and latest inverter control processor door into a door gave smoother movement than the previous one. (4) Brightly easy-to-view and white LED-type operation buttons are used in the hoistway door and car. (translated by NEDO)

Delinquency Among Members of Hong Kong Youth Street Gangs: The Role of the Organizational Structures of Gangs and Triad Affiliations.

Science.gov (United States)

Chui, Wing Hong; Khiatani, Paul Vinod

2018-07-01

This study explores the importance of organizational structures and formal affiliations with the Hong Kong triads to delinquency among youth street gang members in Hong Kong. More specifically, this study examines the relative importance of the number of organizational structures and triad affiliation to patterns of delinquency in a sample of active members of youth street gangs ( N = 201). With the aid of outreach social workers, a convenience sampling method was used to recruit a gender-balanced sample of at-risk youths. Logistic regression analysis of the survey data that was gathered indicated that formal affiliation to Hong Kong triads and the presence of organizational structures significantly increased the odds of delinquency (independently of each other). Suggestions for future research on gang membership and delinquency, with particular reference to the Asian context, are provided.

NCI designated cancer center funding not influenced by organizational structure.

Science.gov (United States)

Wolfe, Margaret E; Yagoda, Daniel; Thurman, Paul W; Luna, Jorge M; Figg, William Douglas

2009-05-01

National Cancer Institutes (NCI) designated cancer centers use one of three organizational structures. The hypothesis of this study is that there are differences in the amount of annual NCI funding per faculty member based on a cancer center's organizational structure. The study also considers the impact of secondary factors (i.e., the existence of a clinical program, the region and the size of the city in which the cancer center is located) on funding and the number of Howard Hughes Medical Institute (HHMI) investigators at each cancer center. Of the 63 cancer centers, 44 use a matrix structure, 16 have a freestanding structure, and three have a Department of Oncology structure. Kruskal-Wallis tests reveal no statistically significant differences in the amount of funding per faculty member or the number of HHMI investigators between centers with a matrix, freestanding or Department of Oncology structure. Online research and telephone interviews with each cancer center were used to gather information, including: organizational structure, the presence of a clinical program, the number of faculty members, and the number of Howard Hughes Medical Institute investigators. Statistical tests were used to assess the impact which organizational structure has on the amount of funding per faculty member and number of HHMI investigators. While the results seem to suggest that the organizational structure of a given cancer center does not impact the amount of NCI funding or number of HHMI investigators which it attracts, the existence of this relationship is likely masked by the small sample size in this study. Further studies may be appropriate to examine the effect organizational structure has on other measurements which are relevant to cancer centers, such as quality and quantity of research produced.

Reasoning Backwards by Design: Commentary on "Moral Reasoning among HEC Members".

Science.gov (United States)

Stephens, Ashley L; Heitman, Elizabeth

2015-01-01

Empirical assessment of the practice of clinical ethics is made difficult by the limited standardization of settings, structures, processes, roles, and training for ethics consultation, as well as by whether individual ethics consultants or hospital ethics committees (HECs) provide consultation. Efforts to study the relationship between theory and practice in the work of HECs likewise require the spelling out of assumptions and definition of key variables, based in knowledge of the core concepts of clinical ethics and logistics of clinical consultation. The survey of HEC members reported by Wasserman and colleagues illustrates the difficulty of such research and calls attention to need for studies of real-time, complex decision making to inform conclusions about how theory affects practice. Copyright 2015 The Journal of Clinical Ethics. All rights reserved.

Sonic hedgehog stimulates the proliferation of rat gastric mucosal cells through ERK activation by elevating intracellular calcium concentration

International Nuclear Information System (INIS)

Osawa, Hiroyuki; Ohnishi, Hirohide; Takano, Koji; Noguti, Takasi; Mashima, Hirosato; Hoshino, Hiroko; Kita, Hiroto; Sato, Kiichi; Matsui, Hirofumi; Sugano, Kentaro

2006-01-01

Sonic Hedgehog (Shh), a member of hedgehog peptides family, is expressed in gastric gland epithelium. To elucidate Shh function to gastric mucosal cells, we examined the effect of Shh on the proliferation of a rat normal gastric mucosal cell line, RGM-1. RGM-1 cells express essential components of Shh receptor system, patched-1, and smoothened. Shh enhanced DNA synthesis in RGM-1 cells and elevated intracellular calcium concentration ([Ca 2+ ] i ). In addition, Shh as well as calcium ionophore A32187 rapidly activated ERK. However, Shh failed to activate ERK under calcium-free culture condition. Pretreatment of cells with PD98059 attenuated the DNA synthesis promoted by Shh. Moreover, when cells were pretreated with cyclopamine, Shh could not elevate [Ca 2+ ] i , activate ERK or promote DNA synthesis. On the other hand, although Shh induced Gli-1 nuclear accumulation in RGM-1 cells, Shh activated ERK even in cells pretreated with actinomycin D. These results indicate that Shh promotes the proliferation of RGM-1 cells through an intracellular calcium- and ERK-dependent but transcription-independent pathway via Patched/Smoothened receptor system

Exploration of Nursing Faculty Members' Lived Experiences of Objective Structured Clinical Examination (OSCE) in Undergraduate Nursing Education

Science.gov (United States)

Obizoba, Cordelia O.

2014-01-01

The purpose of this phenomenological study was to gain an understanding of nursing faculty members' lived experiences of Objective Structured Clinical Examination (OSCE) in undergraduate nursing education. As owners of their programs' curriculum, nursing faculties are charged with the responsibility of providing needed knowledge, skills, and…

Space strategy and governance of ESA small member states

Science.gov (United States)

Sagath, Daniel; Papadimitriou, Angeliki; Adriaensen, Maarten; Giannopapa, Christina

2018-01-01

The European Space Agency (ESA) has twenty-two Member States with a variety of governance structures and strategic priorities regarding their space activities. The objective of this paper is to provide an up-to date overview and a holistic assessment of the national space governance structures and strategic priorities of the eleven smaller Member States (based on annual ESA contributions). A link is made between the governance structure and the main strategic objectives. The specific needs and interests of small and new Member States in the frame of European Space Integration are addressed. The first part of the paper focuses on the national space governance structures in the eleven smaller ESA Member States. The governance models of these Member States are identified including the responsible ministries and the entities entrusted with the implementation of space strategy/policy and programmes of the country. The second part of this paper focuses on the content and analysis of the national space strategies and indicates the main priorities and trends in the eleven smaller ESA Member States. The priorities are categorised with regards to technology domains, the role of space in the areas of sustainability and the motivators for space investments. In a third and final part, attention is given to the specific needs and interests of the smaller Member States in the frame of European space integration. ESA instruments are tailored to facilitate the needs and interests of the eleven smaller and/or new Member States.

Response of humic acid formation to elevated nitrate during chicken manure composting.

Science.gov (United States)

Shi, Mingzi; Wei, Zimin; Wang, Liqin; Wu, Junqiu; Zhang, Duoying; Wei, Dan; Tang, Yu; Zhao, Yue

2018-06-01

Nitrate can stimulate microbes to degrade aromatic compounds, whereas humic acid (HA) as a high molecular weight aromatic compound, its formation may be affected by elevated nitrate during composting. Therefore, this study is conducted to determine the effect of elevated nitrate on HA formation. Five tests were executed by adding different nitrate concentrations to chicken manure composting. Results demonstrate that the concentration of HA in treatment group is significantly decreased compared with control group (p < 0.05), especially in the highest nitrate concentration group. RDA indicates that the microbes associated with HA and environmental parameters are influenced by elevated nitrate. Furthermore, structural equation model reveals that elevated nitrate reduces HA formation by mediating microbes directly, or by affecting ammonia and pH as the indirect drivers to regulate microbial community structure. Copyright © 2018 Elsevier Ltd. All rights reserved.

Cytogenetic effects of ionizing radiation in peripheral lymphocytes of ISS crew members

Science.gov (United States)

Johannes, Christian; Goedecke, Wolfgang; Antonopoulos, Alexandra; Obe, Günter; Horstmann, Markus

High energy radiation is a major risk factor in manned space missions. Astronauts and cosmonauts are exposed to ionising radiations of cosmic and solar origin, while on the Earth's surface people are well protected by the atmosphere and a deflecting magnetic field. There are now data available describing the dose and the quality of ionising radiation on-board of the International Space Station (ISS). The effect of the increased radiation dose on mutation rates of ISS crew members are hard to predict. Therefore, direct measurements of mutation rates are required.The analysis of chromosomal aberrations in peripheral blood lymphocytes is a well established method to measure radiation-induced mutations. We present data of chromosome aberration analyses from lymphocyte metaphase spreads of ISS crew members participating in short term (10-14 days) or long term (6 months) missions. From each subject we received two blood samples. The first sample was drawn about 10 days before launch and a second sample was drawn within 3 days after return from their flights. From lymphocyte cultures metaphase plates were prepared on glass slides. Metaphases were Giemsa stained or hybridised using multicolour FISH probes. All types of chromosome changes were scored in pre-flight and post-flight blood samples and the mutation rates were compared. Results obtained in chromosomal studies on long-term flight crew members showed pronounced inter-individual differences in the response to cosmic radiation exposure. Overall significant elevations of typical radiation induced aberrations, i.e., dicentric chromosomes and reciprocal translocations have been observed in long-term crew members. Our data indicate no elevation of mutation rates due to short-term stays on-board the ISS.

Microfracture behaviour of extruded Mg–Zn–Y alloys containing long-period stacking ordered structure at room and elevated temperatures

International Nuclear Information System (INIS)

Mine, Yoji; Yoshimura, Hajime; Matsuda, Mitsuhiro; Takashima, Kazuki; Kawamura, Yoshihito

2013-01-01

We studied the fracture behaviour of extruded Mg–Zn–Y alloys at room temperature (RT) and at 523 K using microfracture testing. An Mg 97 Zn 1 Y 2 alloy was used to obtain two-phase specimens consisting of α-Mg and long-period stacking ordered (LPSO) structure phases, and an Mg 88 Zn 5 Y 7 alloy was used to obtain specimens consisting of an LPSO phase. The microfracture testing of the two-phase specimen revealed that the fracture behaviour changed from brittle to ductile as the testing temperature increased. By contrast, the LPSO-phase specimen remained brittle even at the elevated temperature and the intrinsic fracture toughness values obtained at both testing temperatures were nearly identical. Ex situ transmission electron microscopy of the two-phase specimen showed that mechanical twinning in the α-Mg phase did not occur at the elevated temperature, although it was activated at RT. This suggests that the plastic deformation mode in the α-Mg phase plays a crucial part in the enhanced crack growth resistance of the two-phase alloy at the elevated temperature

Motivational climate, staff and members' behaviors, and members' psychological well-being at a national fitness franchise.

Science.gov (United States)

Brown, Theresa C; Fry, Mary D

2014-06-01

The purpose of this study was to examine the association between members' perceptions of staffs behaviors, motivational climate, their own behaviors, commitment to future exercise, and life satisfaction in a group-fitness setting. The theory-driven hypothesized mediating role of perceptions of the climate was also tested. Members (N = 5,541) of a national group-fitness studio franchise completed a survey regarding their class experiences. The survey included questions that measured participants' perceptions of the motivational climate (caring, task-involving, ego-involving), perceptions of staff's behaviors, their own behaviors, commitment to exercise, and life satisfaction. Structural equation modeling was used to assess both the association between variables and the theoretically driven predictive relationships. The participants perceived the environment as highly caring and task-involving and low ego-involving. They reported high exercise commitment and moderately high life satisfaction and perceived that the staffs and their own behaviors reflected caring, task-involving characteristics. Structural equation modeling demonstrated that those who perceived a higher caring, task-involving climate and lower ego-involving climate were more likely to report more task-involving, caring behaviors among the staff and themselves as well as greater commitment to exercise. In addition, a theory-driven mediational model suggested that staff behaviors may be an antecedent to members' exercise experiences by impacting their perceptions of the climate. The results of this study give direction to specific behaviors in which staff of group-fitness programs might engage to positively influence members' exercise experiences.

Elevation of blood levels of zinc protoporphyrin by radiomimetic drugs and friend leukemia virus

International Nuclear Information System (INIS)

Walden, T.L.; Al-Ansari, H.M.; Farkas, W.R.; Tennessee Univ., Knoxville; Tennessee Univ., Knoxville

1987-01-01

Sublethal doses of whole-body irradiation induced the elevation of zinc protoporphyrin (ZPP). Experiments were conducted to determine if recovery from radiomimetic drugs also resulted in elevation of ZPP. Daily injections with hydroxyurea and other cytotoxic drugs for 10 days caused ZPP elevation and a dose of radiation too low to cause ZPP elevation by itself caused ZPP elevation when hydroxyurea was administered prior to irradiation. Friend leukemia virus also brought about an elevation of ZPP. However, not all factors that increased erythropoiesis brought about ZPP elevation. The elevated erythropoiesis in response to hypoxia and the enhanced erythropoiesis that followed administration of folic acid to folic acid-deficient mice was not accompanied by ZPP elevation. (orig.)

Elevation of blood levels of zinc protoporphyrin by radiomimetic drugs and friend leukemia virus

Energy Technology Data Exchange (ETDEWEB)

Walden, T.L.; Al-Ansari, H.M.; Farkas, W.R.

1987-01-01

Sublethal doses of whole-body irradiation induced the elevation of zinc protoporphyrin (ZPP). Experiments were conducted to determine if recovery from radiomimetic drugs also resulted in elevation of ZPP. Daily injections with hydroxyurea and other cytotoxic drugs for 10 days caused ZPP elevation and a dose of radiation too low to cause ZPP elevation by itself caused ZPP elevation when hydroxyurea was administered prior to irradiation. Friend leukemia virus also brought about an elevation of ZPP. However, not all factors that increased erythropoiesis brought about ZPP elevation. The elevated erythropoiesis in response to hypoxia and the enhanced erythropoiesis that followed administration of folic acid to folic acid-deficient mice was not accompanied by ZPP elevation.

Traditional biomolecular structure determination by NMR spectroscopy allows for major errors

NARCIS (Netherlands)

Nabuurs, S.B.; Spronk, C.A.E.M.; Vuister, G.W.; Vriend, G.

2006-01-01

One of the major goals of structural genomics projects is to determine the three-dimensional structure of representative members of as many different fold families as possible. Comparative modeling is expected to fill the remaining gaps by providing structural models of homologs of the

Effect of alkali–silica reaction on the shear strength of reinforced concrete structural members. A numerical and statistical study

Energy Technology Data Exchange (ETDEWEB)

Saouma, Victor E.; Hariri-Ardebili, Mohammad Amin [Department of Civil Engineering, University of Colorado, Boulder, CO 80305 (United States); Le Pape, Yann, E-mail: lepapeym@ornl.gov [Oak Ridge National Laboratory, One Bethel Valley Road, Oak Ridge, TN 37831 (United States); Balaji, Rajagopalan [Department of Civil Engineering, University of Colorado, Boulder, CO 80305 (United States)

2016-12-15

Highlights: • Alkali–silica reaction (ASR) affects reinforced structures shear strength. • Statistical analysis indicates large scattering of post-ASR strength losses/gains. • Competitive structural and materials mechanisms affect the residual shear strength. - Abstract: The residual structural shear resistance of concrete members without shear reinforcement and subject to alkali–aggregate reaction (ASR) is investigated by finite element analysis. A parametric numerical study of 648 analyses considering various structural members’ geometries, boundary conditions, ASR-induced losses of materials properties, ASR expansions and reinforcement ratios is conducted. As a result of competitive mechanisms (e.g., ASR-induced prestressing caused by the longitudinal reinforcement) and loss of concrete materials properties, important scatter in terms of gain or loss of shear strength is observed: about 50% of the studied configurations lead to a degradation of structural performance. The range of variation in terms of post-ASR shear resistance is extremely scattered, in particular, when ASR results in out-of-plane expansion only. Influencing factors are derived by two methods: (i) visual inspection of boxplots and probability distributions, and (ii) information criteria within multiple-linear regression analysis.

L10 ordered structures in Al-Cu-(Mg) alloys at the early stages of elevated temperature aging

Energy Technology Data Exchange (ETDEWEB)

Fuzhong, X.; Mingpu, W.

2016-07-01

This study concerns the precipitation structures of Al-3Cu and Al-3Cu-1.78Mg (wt. %) alloys at the early stages of elevated temperature aging. The Al-3Cu and Al-3Cu-1.78 Mg alloys were solution treated at 540 °C and 500 °C for 2 h, respectively, and then aged at 190 °C for 2 min. The precipitation structures in aged Al-3Cu-(1.78Mg) alloys were characterized by Transmission Electron Microscopy (TEM) and High Resolution Transmission Electron Microscopy (HTREM). 001 zone axis Selected area electron diffraction patterns indicate that L10 ordered structures are formed in the two aged alloys. HRTEM experiments reveal the partial dislocations on the interfaces of L10 ordered structures. From comparing experimental results with that in the literature, it is concluded that the L10 ordered structures in aged Al-3Cu alloy consist of Al and Cu atoms, and they are comprised by Al, Cu and Mg atoms together in the aged Al-3Cu-1.78Mg alloy. On the basis of precipitate growing thermodynamics, it is thought the L10 ordered structures act as nuclei for GP zones in Al-Cu-(Mg) alloys during aging. (Author)

L10 ordered structures in Al-Cu-(Mg) alloys at the early stages of elevated temperature aging

International Nuclear Information System (INIS)

Fuzhong, X.; Mingpu, W.

2016-01-01

This study concerns the precipitation structures of Al-3Cu and Al-3Cu-1.78Mg (wt. %) alloys at the early stages of elevated temperature aging. The Al-3Cu and Al-3Cu-1.78 Mg alloys were solution treated at 540 °C and 500 °C for 2 h, respectively, and then aged at 190 °C for 2 min. The precipitation structures in aged Al-3Cu-(1.78Mg) alloys were characterized by Transmission Electron Microscopy (TEM) and High Resolution Transmission Electron Microscopy (HTREM). 001 zone axis Selected area electron diffraction patterns indicate that L10 ordered structures are formed in the two aged alloys. HRTEM experiments reveal the partial dislocations on the interfaces of L10 ordered structures. From comparing experimental results with that in the literature, it is concluded that the L10 ordered structures in aged Al-3Cu alloy consist of Al and Cu atoms, and they are comprised by Al, Cu and Mg atoms together in the aged Al-3Cu-1.78Mg alloy. On the basis of precipitate growing thermodynamics, it is thought the L10 ordered structures act as nuclei for GP zones in Al-Cu-(Mg) alloys during aging. (Author)

Contrasting patterns of phylogenetic assemblage structure along the elevational gradient for major hummingbird clades

DEFF Research Database (Denmark)

Parra, Juan L.; Rahbek, Carsten; McGuire, Jimmy A.

2011-01-01

Aim We evaluated the hypothesis that, given niche conservatism, relatedness of co-occurring hummingbird species of a given clade will increase at greater distances from the elevation where it originated. We also used prior knowledge of flight biomechanics and feeding specialization of hummingbird...... specialization (hermits and brilliants) always included a vegetation-related variable as an important predictor of change in phylogenetic structure. Main conclusions We found no overall support for the conservatism and zone of origin hypotheses. Knowledge of each clade’s natural history proved useful...

E4 - Energy efficient elevators and escalators. Elevators and escalators in Germany from an energy perspective

Energy Technology Data Exchange (ETDEWEB)

Hirzel, Simon; Fleiter, Tobias; Rosende, Daniel

2010-01-31

This report aims to provide a brief introduction to the German elevator and escalator market, and gives an aggregated view of current and future developments focusing on energy consumption and energy-related emissions. This update report of January 2010 is an extended version of a report published in April 2009 before the final results from a monitoring campaign carried out within the project were available. During this campaign, 81 installations (74 elevators and 7 escalators) were monitored in terms of energy consumption. In the first section, the structure of the installed German elevator and escalator capacity is presented. The estimates1 were provided courtesy of the two main associations representing elevators and escalators in Germany: the VDMA (Verband Deutscher Maschinen- und Anlagenbau - German Engineering Federation) and the VFA-Interlift e.V. -Verband fuer Aufzugstechnik (Association for Lift Technology). This section is followed by a short description of the German construction sector and its implications for elevators and escalators. The third section describes German electricity production in terms of its environmental impact with the main focus on the carbon dioxide emissions of the national power plants. Then the energy consumption of elevators and escalators in Germany is analyzed, comparing the results to total energy production in Germany.2 The final section summarizes the different aspects and derives indications about the future development of the total energy consumption of elevators and escalators in Germany. (orig.)

Crystal and NMR Structures of a Peptidomimetic β-Turn That Provides Facile Synthesis of 13-Membered Cyclic Tetrapeptides.

Science.gov (United States)

Cameron, Alan J; Squire, Christopher J; Edwards, Patrick J B; Harjes, Elena; Sarojini, Vijayalekshmi

2017-12-14

Herein we report the unique conformations adopted by linear and cyclic tetrapeptides (CTPs) containing 2-aminobenzoic acid (2-Abz) in solution and as single crystals. The crystal structure of the linear tetrapeptide H 2 N-d-Leu-d-Phe-2-Abz-d-Ala-COOH (1) reveals a novel planar peptidomimetic β-turn stabilized by three hydrogen bonds and is in agreement with its NMR structure in solution. While CTPs are often synthetically inaccessible or cyclize in poor yield, both 1 and its N-Me-d-Phe analogue (2) adopt pseudo-cyclic frameworks enabling near quantitative conversion to the corresponding CTPs 3 and 4. The crystal structure of the N-methylated peptide (4) is the first reported for a CTP containing 2-Abz and reveals a distinctly planar 13-membered ring, which is also evident in solution. The N-methylation of d-Phe results in a peptide bond inversion compared to the conformation of 3 in solution. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Perspectives and expectations of union member and non- union member teachers on teacher unions

Directory of Open Access Journals (Sweden)

Tuncer FİDAN

2015-12-01

Full Text Available Unions, which can be regarded as one of the constitutive elements of democracy, are the pressure groups in political and social fields. Unions were born out of industrial confrontations and expanded into the field of public services over time, and thus teachers – who are also public employees-, also obtained the right to establish and affiliate to unions. In this research the views of union member and non-union member teachers on the most important functions and operational effectiveness of unions, teachers’ expectations from unions and teachers’ evaluation of the solidarity, competition and cooperation between unions were determined and the perspectives of teachers on unionization were revealed. qualitative research design was used. The data needed were collected through semi-structured interviews from volunteering union member and non-union member teachers who were working in the primary and secondary schools in Ankara province and who were selected through “maximum variation sampling approach”. The data were then analyzed by using the content analysis technique. In conclusion, it was found that political ideology was the most important reason for membership of teachers’ unions. Protection and development of personal rights was found to be the most important function of teacher unions and unions were thought to be insufficient in performing those functions.

Residual Tensile Strength and Bond Properties of GFRP Bars after Exposure to Elevated Temperatures

Directory of Open Access Journals (Sweden)

Devon S. Ellis

2018-02-01

Full Text Available The use of fiber reinforced polymer (FRP bars in reinforced concrete members enhances corrosion resistance when compared to traditional steel reinforcing bars. Although there is ample research available on the behavior of FRP bars and concrete members reinforced with FRP bars under elevated temperatures (due to fire, there is little published information available on their post-fire residual load capacity. This paper reports residual tensile strength, modulus of elasticity, and bond strength (to concrete of glass fiber reinforced polymer (GFRP bars after exposure to elevated temperatures of up to 400 °C and subsequent cooling to an ambient temperature. The results showed that the residual strength generally decreases with increasing temperature exposure. However, as much as 83% of the original tensile strength and 27% of the original bond strength was retained after the specimens were heated to 400 °C and then cooled to ambient temperature. The residual bond strength is a critical parameter in post-fire strength assessments of GFRP-reinforced concrete members.

Residual Tensile Strength and Bond Properties of GFRP Bars after Exposure to Elevated Temperatures.

Science.gov (United States)

Ellis, Devon S; Tabatabai, Habib; Nabizadeh, Azam

2018-02-27

The use of fiber reinforced polymer (FRP) bars in reinforced concrete members enhances corrosion resistance when compared to traditional steel reinforcing bars. Although there is ample research available on the behavior of FRP bars and concrete members reinforced with FRP bars under elevated temperatures (due to fire), there is little published information available on their post-fire residual load capacity. This paper reports residual tensile strength, modulus of elasticity, and bond strength (to concrete) of glass fiber reinforced polymer (GFRP) bars after exposure to elevated temperatures of up to 400 °C and subsequent cooling to an ambient temperature. The results showed that the residual strength generally decreases with increasing temperature exposure. However, as much as 83% of the original tensile strength and 27% of the original bond strength was retained after the specimens were heated to 400 °C and then cooled to ambient temperature. The residual bond strength is a critical parameter in post-fire strength assessments of GFRP-reinforced concrete members.

Synchronous Control Method and Realization of Automated Pharmacy Elevator

Science.gov (United States)

Liu, Xiang-Quan

Firstly, the control method of elevator's synchronous motion is provided, the synchronous control structure of double servo motor based on PMAC is accomplished. Secondly, synchronous control program of elevator is implemented by using PMAC linear interpolation motion model and position error compensation method. Finally, the PID parameters of servo motor were adjusted. The experiment proves the control method has high stability and reliability.

UPF201 Archaeal Specific Family Members Reveals Structural Similarity to RNA-Binding Proteins but Low Likelihood for RNA-Binding Function

Energy Technology Data Exchange (ETDEWEB)

Rao, K.N.; Swaminathan, S.; Burley, S. K.

2008-12-11

We have determined X-ray crystal structures of four members of an archaeal specific family of proteins of unknown function (UPF0201; Pfam classification: DUF54) to advance our understanding of the genetic repertoire of archaea. Despite low pairwise amino acid sequence identities (10-40%) and the absence of conserved sequence motifs, the three-dimensional structures of these proteins are remarkably similar to one another. Their common polypeptide chain fold, encompassing a five-stranded antiparallel {beta}-sheet and five {alpha}-helices, proved to be quite unexpectedly similar to that of the RRM-type RNA-binding domain of the ribosomal L5 protein, which is responsible for binding the 5S- rRNA. Structure-based sequence alignments enabled construction of a phylogenetic tree relating UPF0201 family members to L5 ribosomal proteins and other structurally similar RNA binding proteins, thereby expanding our understanding of the evolutionary purview of the RRM superfamily. Analyses of the surfaces of these newly determined UPF0201 structures suggest that they probably do not function as RNA binding proteins, and that this domain specific family of proteins has acquired a novel function in archaebacteria, which awaits experimental elucidation.

Elevating your elevator talk

Science.gov (United States)

An important and often overlooked item that every early career researcher needs to do is compose an elevator talk. The elevator talk, named because the talk should not last longer than an average elevator ride (30 to 60 seconds), is an effective method to present your research and yourself in a clea...

STUDY ON COMMUNICATION TEAM’S MEMBERS ROLES

Directory of Open Access Journals (Sweden)

Cristina BORCA

2014-06-01

Full Text Available The implementation of the management strategy for increasing the competitiveness of modern organizations is more effective if it is correlated with the organizational communication strategy. Team communication of an organization must be an agile one, its agility depending decisively on the way it was constituted, the assigned role for each team member, the statuses etc. A valuation of all skills and abilities of each member of the communication team is therefore required to harmonize and integrate the team into the overall structure of the company. The objective of the paper is to identify the extent to which the formal role of each team member is the same (almost the same with the role determined by applying the Belbin test. The results of the research are prerequisites for development of measures for individual professional development and integration /reintegration of team members in order to increase agility.

The Foreign Policies of European Union Member States

DEFF Research Database (Denmark)

Foreign Policies of EU Member States provides a clear and current overview of the motivations and outcomes of EU Member States regarding their foreign policy-making within and beyond the EU. It provides an in-depth analysis of intra-EU policy-making and sheds light, in an innovative and understan......Foreign Policies of EU Member States provides a clear and current overview of the motivations and outcomes of EU Member States regarding their foreign policy-making within and beyond the EU. It provides an in-depth analysis of intra-EU policy-making and sheds light, in an innovative...... prerogative exercised by all EU Member States is to construct their own foreign policies on everything from trade and defence with the rest of the world. This combination of clarity, thematic structure and empirical case studies make this an ideal textbook for all upper-level students of European foreign...

Structure of BT-3984, a member of the SusD/RagB family of nutrient-binding molecules

International Nuclear Information System (INIS)

Bakolitsa, Constantina; Xu, Qingping; Rife, Christopher L.; Abdubek, Polat; Astakhova, Tamara; Axelrod, Herbert L.; Carlton, Dennis; Chen, Connie; Chiu, Hsiu-Ju; Clayton, Thomas; Das, Debanu; Deller, Marc C.; Duan, Lian; Ellrott, Kyle; Farr, Carol L.; Feuerhelm, Julie; Grant, Joanna C.; Grzechnik, Anna; Han, Gye Won; Jaroszewski, Lukasz; Jin, Kevin K.; Klock, Heath E.; Knuth, Mark W.; Kozbial, Piotr; Krishna, S. Sri; Kumar, Abhinav; Lam, Winnie W.; Marciano, David; McMullan, Daniel; Miller, Mitchell D.; Morse, Andrew T.; Nigoghossian, Edward; Nopakun, Amanda; Okach, Linda; Puckett, Christina; Reyes, Ron; Tien, Henry J.; Trame, Christine B.; Bedem, Henry van den; Weekes, Dana; Hodgson, Keith O.; Wooley, John; Elsliger, Marc-André; Deacon, Ashley M.; Godzik, Adam; Lesley, Scott A.; Wilson, Ian A.

2010-01-01

The crystal structure of BT-3984, a SusD-family protein, reveals a TPR N-terminal region providing support for a loop-rich C-terminal subdomain and suggests possible interfaces involved in sus complex formation. The crystal structure of the Bacteroides thetaiotaomicron protein BT-3984 was determined to a resolution of 1.7 Å and was the first structure to be determined from the extensive SusD family of polysaccharide-binding proteins. SusD is an essential component of the sus operon that defines the paradigm for glycan utilization in dominant members of the human gut microbiota. Structural analysis of BT-3984 revealed an N-terminal region containing several tetratricopeptide repeats (TPRs), while the signature C-terminal region is less structured and contains extensive loop regions. Sequence and structure analysis of BT-3984 suggests the presence of binding interfaces for other proteins from the polysaccharide-utilization complex

Magnetically levitated space elevator to low-earth orbit

International Nuclear Information System (INIS)

Hull, J. R.; Mulcahy, T. M.

2001-01-01

The properties of currently available NbTi superconductor and carbon-fiber structural materials enable the possibility of constructing a magnetically levitated space elevator from the earth's surface up to an altitude of(approx) 200 km. The magnetic part of the elevator consists of a long loop of current-carrying NbTi, composed of one length that is attached to the earth's surface in an east-west direction and a levitated-arch portion. The critical current density of NbTi is sufficiently high that these conductors will stably levitate in the earth's magnetic field. The magnetic self-field from the loop increases the levitational force and for some geometries assists levitational stability. The 200-km maximum height of the levitated arch is limited by the allowable stresses of the structural material. The loop is cryogenically cooled with helium, and the system utilizes intermediate pumping and cooling stations along both the ground and the levitated portion of the loop, similar to other large terrestrial cryogenic systems. Mechanically suspended from the basic loop is an elevator structure, upon which mass can be moved between the earth's surface and the top of the loop by a linear electric motor or other mechanical or electrical means. At the top of the loop, vehicles may be accelerated to orbital velocity or higher by rocket motors, electromagnetic propulsion, or hybrid methods

Suicidal Ideation and Distress in Family Members Bereaved by Suicide in Portugal

OpenAIRE

Santos, Sara; Campos, Rui; Tavares, Sofia

2015-01-01

The present study assessed the impact of suicide and distress on suicidal ideation in a sample of 93 Portuguese family members bereaved by suicide. A control community sample of 102 adults also participated. After controlling for educational level, those bereaved by the suicide of a family member were found to have higher levels of suicidal ideation. Forty-two percent of family members had Suicide Ideation Questionnaire scores at or above the cutoff point. General distress, dep...

The vast polar structure of the Milky Way attains new members

Energy Technology Data Exchange (ETDEWEB)

Pawlowski, Marcel S. [Department of Astronomy, Case Western Reserve University, 10900 Euclid Avenue, Cleveland, OH 44106 (United States); Kroupa, Pavel, E-mail: marcel.pawlowski@case.edu [Helmholtz-Institut für Strahlen-und Kernphysik, Rheinische Friedrich-Wilhelms-Universität Bonn, Nussallee 14-16, D-53115 Bonn (Germany)

2014-07-20

The satellite galaxies of the Milky Way (MW) align with and preferentially orbit in a vast polar structure (VPOS), which also contains globular clusters (GCs) and stellar and gaseous streams. Similar alignments have been discovered around several other host galaxies. We test whether recently discovered objects in the MW halo, the satellite galaxy/GC transition object named PSO J174.0675-10.8774 or Crater and three stellar streams, are part of the VPOS. Crater is situated close to the VPOS. Incorporating the new object in the VPOS-plane fit slightly improves the alignment of the plane with other features such as the Magellanic stream and the average orbital plane of the satellites co-orbiting in the VPOS. We predict Crater's proper motion by assuming that it, too, orbits in the VPOS. One of the three streams aligns well with the VPOS. Surprisingly, it appears to lie in the exact same orbital plane as the Palomar 5 stream and shares its distance, suggesting a direct connection between the two. The stream also crosses close to the Fornax dwarf galaxy and is oriented approximately along the galaxy's direction of motion. The two other streams cannot align closely with the VPOS because they were discovered in the direction of M31/M33, which is outside of the satellite structure. The VPOS thus attains two new members. This further emphasizes that the highly anisotropic and correlated distribution of satellite objects requires an explanation beyond the suggestion that the MW satellite system is an extreme statistical outlier of a ΛCDM sub-halo system.

Finding the displacement of wood structure in heritage building by 3D laser scanner

Science.gov (United States)

Lee, M. C.; Tsai, Y. L.; Wang, R. Z.; Lin, M. L.

2015-08-01

Heritage buildings are highly prone to long term damage from the microclimate, scourge and vandalism, which can result in damaged materials, structures, painting and cultural heritage items. This study will focus on finding the displacement of wood structural members through the use of a 3D laser scanner and the 4D concept of time. The results will compare the scans from different periods to find the difference (if any) in the structural member position. Wood structures usually consist of numerous wood members connected to form the structure. However, these members can be damaged in various ways such as physical mechanisms, chemical reactions, and biological corrosion. When damage to the wood structure occurs, the structural displacement can be affected, and if affected severely, can lead to a building collapse. Monitoring of the structural displacement is the best way to discover damage immediately and to preserve the heritage building. However, the Cultural Heritage Preservation Law in Taiwan prohibits the installation of monitoring instruments (e.g strain gauge, accelerometer) in historic structures (heritage buildings). Scanning the wood structure with 3D lasers is the most non-intrusive method and quickly achieves displacement through visualization. The displacement scan results can be compared with different periods and different members to analyze the severity of damage. Once the 3D scanner is installed, the whole building is scanned, and point clouds created to build the visual building model. The structural displacement can be checked via the building model and the differences are measured between each member to find the high risk damaged areas or members with large displacement. Early detection of structural damage is the most effective way means of preservation.

Evaluation of Faculty Members by Students in Birjand University of Medicine, 2003-2004

Directory of Open Access Journals (Sweden)

Masood Ziaie

2009-02-01

Full Text Available Background and purpose: Evaluation of faculty members is a kind of educational evaluation to determine success of faculty members in reaching the educational goals. Regarding the controversy about the validity of this kind of evaluation, this study was done to examine faculty members and students view point about content and implementation of evaluation of faculty members by students and feedback of the results in the second term of academic year 2003-4 in Birjand University of Medicine.Methods: All faculty members and students participated in this descriptive study. Their opinions were studied using two questionnaires for students and faculty members separately, whose content validity were confirmed after a survey from specialists and pilot study and reliability of results werestudied through calculating Cronbach’s alpha coefficient for internal consistency .Data were analyzed through calculating frequencies and K2-test, α=0.05.Results: Of all faculty members, 95% ( 30 from clinical and 30 from non clinical departments were aware of having been evaluated by students, 81.7% of them recognize educational development center of the University as the responsible body for evaluation. 91.7% of them received the feedback of the evaluation results. 45% of them agreed that announcement of evaluation results was helpful to improve teaching. 40% believed that questionnaires were responded without dutifulness andcarefulness by students.Conclusion: The aim of teaching evaluation is to improve teaching by faculty members. But it seems that many faculty members do not regard this evaluation tool so valid for measuring their teaching activities. The inappropriateness of most of the questionnaires, unfair judgment of student, and careless selection of the sample of students who answer the questionnaires are major issues for further development.Key words: EVALUATION, FACULTY MEMBER, STUDENT, MEDICAL UNIVERSITY OF BIRJAND

effect of elevated temperature on the compressive strength

African Journals Online (AJOL)

HOD

reducing cost whilst maintaining structural integrity. [1–4].The solid ... density and surface appearance are affected by temperature .... Table 1: Physical properties of Sand, Granite, cement .... The relationship between weight loss and elevated.

Plant dieback under exceptional drought driven by elevation, not by plant traits, in Big Bend National Park, Texas, USA

Directory of Open Access Journals (Sweden)

Elizabeth F. Waring

2014-07-01

Full Text Available In 2011, Big Bend National Park, Texas, USA, experienced the most severe single year drought in its recorded history, resulting in significant plant mortality. We used this event to test how perennial plant response to drought varied across elevation, plant growth form and leaf traits. In October 2010 and October 2011, we measured plant cover by species at six evenly-spaced elevations ranging from Chihuahuan desert (666 m to oak forest in the Chisos mountains (1,920 m. We asked the following questions: what was the relationship between elevation and stem dieback and did susceptibility to drought differ among functional groups or by leaf traits? In 2010, pre-drought, we measured leaf mass per area (LMA on each species. In 2011, the percent of canopy dieback for each individual was visually estimated. Living canopy cover decreased significantly after the drought of 2011 and dieback decreased with elevation. There was no relationship between LMA and dieback within elevations. The negative relationship between proportional dieback and elevation was consistent in shrub and succulent species, which were the most common growth forms across elevations, indicating that dieback was largely driven by elevation and not by species traits. Growth form turnover did not influence canopy dieback; differences in canopy cover and proportional dieback among elevations were driven primarily by differences in drought severity. These results indicate that the 2011 drought in Big Bend National Park had a large effect on communities at all elevations with average dieback for all woody plants ranging from 8% dieback at the highest elevation to 83% dieback at lowest elevations.

Structural insights into the elevator-like mechanism of the sodium/citrate symporter CitS.

Science.gov (United States)

Kim, Ji Won; Kim, Subin; Kim, Songwon; Lee, Haerim; Lee, Jie-Oh; Jin, Mi Sun

2017-05-31

The sodium-dependent citrate transporter of Klebsiella pneumoniae (KpCitS) belongs to the 2-hydroxycarboxylate transporter (2-HCT) family and allows the cell to use citrate as sole carbon and energy source in anaerobic conditions. Here we present crystal structures of KpCitS in citrate-bound outward-facing, citrate-bound asymmetric, and citrate-free inward-facing state. The structures reveal that the KpCitS dimerization domain remains stationary throughout the transport cycle due to a hydrogen bond network as well as extensive hydrophobic interactions. In contrast, its transport domain undergoes a ~35° rigid-body rotation and a ~17 Å translocation perpendicular to the membrane to expose the substrate-binding site alternately to either side of the membrane. Furthermore, homology models of two other 2-HCT proteins based on the KpCitS structure offer structural insights into their differences in substrate specificity at a molecular level. On the basis of our results and previous biochemical data, we propose that the activity of the 2-HCT CitS involves an elevator-like movement in which the transport domain itself traverses the lipid bilayer, carrying the substrate into the cell in a sodium-dependent manner.

18-Membered cyclic esters derived from glycolide and lactide: preparations, structures and coordination to sodium ions

Energy Technology Data Exchange (ETDEWEB)

Chisholm, Malcolm H.; Gallucci, Judith C.; Yin, Hongfeng (OSU)

2008-06-30

From reactions between glycolide or lactide (4 equiv.) with 4-dimethylaminopyridine, DMAP (1 equiv.) and NaBPh4 (1 equiv.) in benzene at 70 C the cyclic ester adducts (CH{sub 2}C(O)O){sub 6}NaBPh{sub 4} and (CHMeC(O)O){sub 6}NaBPh{sub 4} are formed respectively. The structures of the salts Na[(S,R,S,R,S,R)-(CH{sub 3}CHC(O)O){sub 6}]{sub 2}BPh{sub 4} {center_dot} CH{sub 3}CN and (CH{sub 2}C(O)O){sub 6}NaBPh{sub 4} {center_dot} (CH{sub 3}CN){sub 2} are reported. The cyclic esters were separated by chromatography and the structures of (CH{sub 2}C(O)O){sub 6}, (S,R,R,R,R,R)-(CHMeC(O)O){sub 6} and (S,S,R,R,R,R)-(CHMeC(O)O){sub 6} were determined. The {sup 1}H and {sup 13}C NMR data are reported for one of each of the six enantiomers of (CHMeC(O)O){sub 6} and the two meso isomers. The mechanism for the formation of these 18-membered rings is discussed in terms of an initial reaction between DMAP and NaBPh{sub 4} in hot benzene that produces NaPh and DMAP:BPh{sub 3} in the presence of the monomer lactide. The cyclic esters (CHMeC(O)O){sub 6} can also be obtained from the reaction between polylactide, PLA, in the presence of DMAP and NaBPh{sub 4}. The cyclic esters 3-methyl-1,4-dioxane-2,5-dione and 3,6,6-trimethyl-1,4-dioxane-2,5-dione undergo similar ring enlarging reactions to give cyclic 18-membered ring esters as determined by ESI-MS.

Tritium labeling of simple 7-membered ring compounds

International Nuclear Information System (INIS)

Hiltunen, J.; Peng, C.T.; Yang, Z.C.

1990-01-01

Seven-membered ring compounds, from cycloheptane to complex ring structures containing heteroatoms, substituents and fused phenyl rings, were labeled with tritium, using activated and adsorbed tritium. The 7-membered ring structures are generally stable towards reactions with tritium, which allows compounds like 1-benzosuberone, 1-aza-2-methoxy-1-cycloheptane, iminostilbene and clozapine to be labeled to reasonably high specific activities. The best method varies greatly from compound to compound. By optimizing the labeling conditions and use of efficient support exceptionally good results can be obtained. The Pd-on-alumina support gives consistently higher specific activity and less radioimpurity than other supports. Even molecules containing carbon-halogen bond and hydrogen bound to nitrogen can usually be labeled with tritium at stable positions and without dehalogenation. (author)

PROCESSING OF UAV BASED RANGE IMAGING DATA TO GENERATE DETAILED ELEVATION MODELS OF COMPLEX NATURAL STRUCTURES

Directory of Open Access Journals (Sweden)

T. K. Kohoutek

2012-07-01

Full Text Available Unmanned Aerial Vehicles (UAVs are more and more used in civil areas like geomatics. Autonomous navigated platforms have a great flexibility in flying and manoeuvring in complex environments to collect remote sensing data. In contrast to standard technologies such as aerial manned platforms (airplanes and helicopters UAVs are able to fly closer to the object and in small-scale areas of high-risk situations such as landslides, volcano and earthquake areas and floodplains. Thus, UAVs are sometimes the only practical alternative in areas where access is difficult and where no manned aircraft is available or even no flight permission is given. Furthermore, compared to terrestrial platforms, UAVs are not limited to specific view directions and could overcome occlusions from trees, houses and terrain structures. Equipped with image sensors and/or laser scanners they are able to provide elevation models, rectified images, textured 3D-models and maps. In this paper we will describe a UAV platform, which can carry a range imaging (RIM camera including power supply and data storage for the detailed mapping and monitoring of complex structures, such as alpine riverbed areas. The UAV platform NEO from Swiss UAV was equipped with the RIM camera CamCube 2.0 by PMD Technologies GmbH to capture the surface structures. Its navigation system includes an autopilot. To validate the UAV-trajectory a 360° prism was installed and tracked by a total station. Within the paper a workflow for the processing of UAV-RIM data is proposed, which is based on the processing of differential GNSS data in combination with the acquired range images. Subsequently, the obtained results for the trajectory are compared and verified with a track of a UAV (Falcon 8, Ascending Technologies carried out with a total station simultaneously to the GNSS data acquisition. The results showed that the UAV's position using differential GNSS could be determined in the centimetre to the decimetre

Board effectiveness: Investigating payment asymmetry between board members and shareholders

Directory of Open Access Journals (Sweden)

Wuchun Chi

2008-01-01

Full Text Available Board members may well be responsible for dissension between themselves and shareholders since they are simultaneously the setters and receivers of both board remuneration and dividends. They may act out of their own personal interests at the expense of external shareholders. We investigate the impact of ownership structure, board structure and control deviation on payment asymmetry, where excessively high remuneration is paid to board members but considerably lower dividends are distributed to shareholders. We find strong evidence confirming that the smaller the shareholdings of board members and outside blockholders are, the more asymmetric the payments are. With controlling family members on the board and a higher percentage of seats held by independent board members, there is a slight reduction in the likelihood and severity of payment asymmetry. In addition, it is abundantly clear that the larger the board seat-control deviation is, the greater is the likelihood and severity of payment asymmetry. While prior research has primarily focused on board-manager agency issues, the board-shareholder perspective could be even more important in that it is the board that is the most directly delegated agent of shareholders, not the managers

Chemical and anatomical changes in Liquidambar styraciflua L. xylem after long term exposure to elevated CO2

International Nuclear Information System (INIS)

Kim, Keonhee; Labbé, Nicole; Warren, Jeffrey M.; Elder, Thomas; Rials, Timothy G.

2015-01-01

The anatomical and chemical characteristics of sweetgum were studied after 11 years of elevated CO 2 (544 ppm, ambient at 391 ppm) exposure. Anatomically, branch xylem cells were larger for elevated CO 2 trees, and the cell wall thickness was thinner. Chemically, elevated CO 2 exposure did not impact the structural components of the stem wood, but non-structural components were significantly affected. Principal component analysis (PCA) was employed to detect differences between the CO 2 treatments by considering numerous structural and chemical variables, as well as tree size, and data from previously published sources (i.e., root biomass, production and turnover). The PCA results indicated a clear separation between trees exposed to ambient and elevated CO 2 conditions. Correlation loadings plots of the PCA revealed that stem structural components, ash, Ca, Mg, total phenolics, root biomass, production and turnover were the major responses that contribute to the separation between the elevated and ambient CO 2 treated trees. - Highlights: • First study of wood properties after 11 years of higher level of CO 2 treatment. • Elevated CO 2 exposure does not impact structural components of wood. • Total phenolics content and some inorganics were significantly affected. • Branch xylem cells were larger under elevated CO 2 . • Cell wall thickness was thinner under elevated CO 2 . - Elevated CO 2 in atmosphere did not impact the structural components yet altered some of non-structural components and anatomical properties after 11 years of exposure on sweetgum

Safe electrical design of mine elevator control systems

Energy Technology Data Exchange (ETDEWEB)

Barkand, T.D. [Mine Safety and Health Administration, Pittsburgh, PA (United States)

1995-12-31

A mine elevator recently experienced an ascending car overspeed accident resulting in serious injuries to four passengers. Although the four miners laid down on the floor prior to impact, the miners struck the ceiling of the elevator car as it collided into the overhead structure at an estimated speed four times faster than normal. Several electrical design precautions can be implemented to prevent elevator control system failures. This paper examines safe electrical design of elevator control systems. Supplemental circuits and devices which improve the safety integrity and maintenance of the elevator control system are presented. These circuits and devices provide protection that eliminates the potential hazard and significantly reduces the possibility of a mine elevator accident.

Safe electrical design of mine elevator control systems

Energy Technology Data Exchange (ETDEWEB)

Barkand, T.D. [Mine Safety and Health Administration, Pittsburgh, PA (United States)

1997-03-01

A mine elevator recently experienced an ascending-car overspeed accident, resulting in serious injuries to four passengers. Although the four miners laid down on the floor prior to impact, the miners struck the ceiling of the elevator car as it collided into the overhead structure at an estimated speed four times faster than normal. Several electrical design precautions can be implemented to prevent elevator control system failures. This paper examines safe electrical design of elevator control systems. Supplemental circuits and devices which improve the safety integrity and maintenance of the elevator control system are presented. These circuits and devices provide protection that eliminates the potential hazard and significantly reduces the possibility of a mine elevator accident.

Arbuscular mycorrhizal fungal community composition affected by original elevation rather than translocation along an altitudinal gradient on the Qinghai-Tibet Plateau

Science.gov (United States)

Yang, Wei; Zheng, Yong; Gao, Cheng; Duan, Ji-Chuang; Wang, Shi-Ping; Guo, Liang-Dong

2016-11-01

Elucidating arbuscular mycorrhizal (AM) fungal responses to elevation changes is critical to improve understanding of microbial function in ecosystems under global asymmetrical climate change scenarios. Here we examined AM fungal community in a two-year reciprocal translocation of vegetation-intact soil blocks along an altitudinal gradient (3,200 m to 3,800 m) in an alpine meadow on the Qinghai-Tibet Plateau. AM fungal spore density was significantly higher at lower elevation than at higher elevation regardless of translocation, except that this parameter was significantly increased by upward translocation from original 3,200 m to 3,400 m and 3,600 m. Seventy-three operational taxonomic units (OTUs) of AM fungi were recovered using 454-pyrosequencing of 18S rDNA sequences at a 97% sequence similarity. Original elevation, downward translocation and upward translocation did not significantly affect AM fungal OTU richness. However, with increasing altitude the OTU richness of Acaulosporaceae and Ambisporaceae increased, but the OTU richness of Gigasporaceae and Glomeraceae decreased generally. The AM fungal community composition was significantly structured by original elevation but not by downward translocation and upward translocation. Our findings highlight that compared with the short-term reciprocal translocation, original elevation is a stronger determinant in shaping AM fungal community in the Qinghai-Tibet alpine meadow.

Ethical Leadership, Leader-Member Exchange and Feedback Seeking: A Double-Moderated Mediation Model of Emotional Intelligence and Work-Unit Structure

Science.gov (United States)

Qian, Jing; Wang, Bin; Han, Zhuo; Song, Baihe

2017-01-01

This research elucidates the role of ethical leadership in employee feedback seeking by examining how and when ethical leadership may exert a positive influence on feedback seeking. Using matched reports from 64 supervisors and 265 of their immediate employees from a hotel group located in a major city in China, we proposed and tested a moderated mediation model that examines leader-member exchange (LMX) as the mediator and emotional intelligence as well as work-unit structure as double moderators in the relationships between ethical leadership and followers’ feedback-seeking behavior from supervisors and coworkers. Our findings indicated that (1) LMX mediated the positive relationship between ethical leadership and feedback seeking from both ethical leaders and coworkers, and (2) emotional intelligence and work-unit structure served as joint moderators on the mediated positive relationship in such a way that the relationship was strongest when the emotional intelligence was high and work-unit structure was more of an organic structure rather than a mechanistic structure. PMID:28744251

Analysis of replies to an IAEA questionnaire on regulatory practices in Member States with nuclear power programmes

International Nuclear Information System (INIS)

1988-10-01

The survey of regulatory practices in Member States with nuclear power programmes by means of a questionnaire is the first stage of the programme developed by the IAEA to assist the Member States in the enhancement of their regulatory practices. The questionnaire, drafted by IAEA staff members and consultants, consisted of 120 detailed questions and its structure corresponds approximately to the Structure of Code on the Safety of Nuclear Power Plants: Governmental Organizations (IAEA Safety Series No. 50-C-G-Rev.1). The questionnaire was sent to 64 Member States on 7 July 1987 and the replies received from 44 Member States have been analysed by IAEA staff members with the assistance of two consultants in order to identify the main differences in approach and the important features of regulatory practices in Member States. This technical document is the summary report of this analysis

Magnetically levitated space elevator to low-earth orbit.

Energy Technology Data Exchange (ETDEWEB)

Hull, J. R.; Mulcahy, T. M.

2001-07-02

The properties of currently available NbTi superconductor and carbon-fiber structural materials enable the possibility of constructing a magnetically levitated space elevator from the earth's surface up to an altitude of {approx} 200 km. The magnetic part of the elevator consists of a long loop of current-carrying NbTi, composed of one length that is attached to the earth's surface in an east-west direction and a levitated-arch portion. The critical current density of NbTi is sufficiently high that these conductors will stably levitate in the earth's magnetic field. The magnetic self-field from the loop increases the levitational force and for some geometries assists levitational stability. The 200-km maximum height of the levitated arch is limited by the allowable stresses of the structural material. The loop is cryogenically cooled with helium, and the system utilizes intermediate pumping and cooling stations along both the ground and the levitated portion of the loop, similar to other large terrestrial cryogenic systems. Mechanically suspended from the basic loop is an elevator structure, upon which mass can be moved between the earth's surface and the top of the loop by a linear electric motor or other mechanical or electrical means. At the top of the loop, vehicles may be accelerated to orbital velocity or higher by rocket motors, electromagnetic propulsion, or hybrid methods.

Reproductive allocation in plants as affected by elevated carbon dioxide and other environmental changes: a synthesis using meta-analysis and graphical vector analysis.

Science.gov (United States)

Wang, Xianzhong; Taub, Daniel R; Jablonski, Leanne M

2015-04-01

Reproduction is an important life history trait that strongly affects dynamics of plant populations. Although it has been well documented that elevated carbon dioxide (CO2) in the atmosphere greatly enhances biomass production in plants, the overall effect of elevated CO2 on reproductive allocation (RA), i.e., the proportion of biomass allocated to reproductive structures, is little understood. We combined meta-analysis with graphical vector analysis to examine the overall effect of elevated CO2 on RA and how other environmental factors, such as low nutrients, drought and elevated atmospheric ozone (O3), interacted with elevated CO2 in affecting RA in herbaceous plants. Averaged across all species of different functional groups and environmental conditions, elevated CO2 had little effect on RA (-0.9%). RA in plants of different reproductive strategies and functional groups, however, differed in response to elevated CO2. For example, RA in iteroparous wild species decreased by 8%, while RA in iteroparous crops increased significantly (+14%) at elevated CO2. RA was unaffected by CO2 in plants grown with no stress or in low-nutrient soils. RA decreased at elevated CO2 and elevated O3, but increased in response to elevated CO2 in drought-stressed plants, suggesting that elevated CO2 could ameliorate the adverse effect of drought on crop production to some extent. Our results demonstrate that elevated CO2 and other global environmental changes have the potential to greatly alter plant community composition through differential effects on RA of different plant species and thus affect the dynamics of natural and agricultural ecosystems in the future.

Agreement on the Privileges and Immunities of the Agency. Acceptances by Member States

International Nuclear Information System (INIS)

1973-01-01

The list of Member States overleaf shows the 41 Members which, by 30 November 1972, had accepted the Agreement on the Privileges and Immunities of the International Atomic Energy Agency, as provided for in Section 38 thereof. Members are listed in alphabetical order, which is different in versions of this document in other languages. The list is followed by the texts of such reservations to the Agreement as some of the Members in question made when depositing their respective instruments of acceptance with the Director General. The reservations are reproduced in the sequence in which the instruments of acceptance to which they relate were deposited

Agreement on the Privileges and Immunities of the Agency. Acceptances by Member States

International Nuclear Information System (INIS)

1969-01-01

The list of Member States overleaf shows the 35 Members which, by 1 November 1969, had accepted the Agreement on the Privileges and Immunities of the International Atomic Energy Agency, as provided for in Section 38 thereof. Members are listed in alphabetical order, which is different in versions of this document in other languages. The list is followed by the texts of such reservations to the Agreement as some of the Members in question made when depositing their respective instruments of acceptance with the Director General. The reservations are reproduced in the sequential order of the deposit of the instruments of acceptance to which they relate

Agreement on the Privileges and Immunities of the Agency. Acceptances by Member States

Energy Technology Data Exchange (ETDEWEB)

NONE

1969-11-27

The list of Member States overleaf shows the 35 Members which, by 1 November 1969, had accepted the Agreement on the Privileges and Immunities of the International Atomic Energy Agency, as provided for in Section 38 thereof. Members are listed in alphabetical order, which is different in versions of this document in other languages. The list is followed by the texts of such reservations to the Agreement as some of the Members in question made when depositing their respective instruments of acceptance with the Director General. The reservations are reproduced in the sequential order of the deposit of the instruments of acceptance to which they relate.

Agreement on the Privileges and Immunities of the Agency. Acceptances by Member States

Energy Technology Data Exchange (ETDEWEB)

NONE

1973-01-15

The list of Member States overleaf shows the 41 Members which, by 30 November 1972, had accepted the Agreement on the Privileges and Immunities of the International Atomic Energy Agency, as provided for in Section 38 thereof. Members are listed in alphabetical order, which is different in versions of this document in other languages. The list is followed by the texts of such reservations to the Agreement as some of the Members in question made when depositing their respective instruments of acceptance with the Director General. The reservations are reproduced in the sequence in which the instruments of acceptance to which they relate were deposited.

A Family Affair : Explaining Co-Working By Family Members

NARCIS (Netherlands)

Ruijter, Esther de; Lippe, Tanja van der; Raub, Werner; Weessie, Jeroen

2008-01-01

This study focuses on co-working by intimate partners and other family members in entrepreneurs’ businesses. We hypothesize that co-working by family is beneficial because it reduces trust problems associated with employment relations. On the other hand, co-working is risky because co-working family

Five-membered heterocycles. Part II. Crystal structures and HOMA index calculations for selected 1,3,4-thiadiazole derivatives

Science.gov (United States)

Mrozek, A.; Karolak-Wojciechowska, J.; Amiel, P.; Barbe, J.

2000-06-01

Crystal structures of four bisubstituted 1,3,4-thiadiazole derivatives were determined. Detailed description of the five-membered heteroring geometry is enabled thorough analysis of ring aromaticity. For this purpose the HOMA index was used as a quantitative measure of aromaticity. The calculated HOMA indices evidenced the role of substituents. In particular, increase in the substituent electrophilicity brings about increase in aromaticity.

Elevated Liver Enzymes

Science.gov (United States)

Symptoms Elevated liver enzymes By Mayo Clinic Staff Elevated liver enzymes may indicate inflammation or damage to cells in the liver. Inflamed or ... than normal amounts of certain chemicals, including liver enzymes, into the bloodstream, which can result in elevated ...

Multi Car Elevator Control by using Learning Automaton

Science.gov (United States)

Shiraishi, Kazuaki; Hamagami, Tomoki; Hirata, Hironori

We study an adaptive control technique for multi car elevators (MCEs) by adopting learning automatons (LAs.) The MCE is a high performance and a near-future elevator system with multi shafts and multi cars. A strong point of the system is that realizing a large carrying capacity in small shaft area. However, since the operation is too complicated, realizing an efficient MCE control is difficult for top-down approaches. For example, “bunching up together" is one of the typical phenomenon in a simple traffic environment like the MCE. Furthermore, an adapting to varying environment in configuration requirement is a serious issue in a real elevator service. In order to resolve these issues, having an autonomous behavior is required to the control system of each car in MCE system, so that the learning automaton, as the solutions for this requirement, is supposed to be appropriate for the simple traffic control. First, we assign a stochastic automaton (SA) to each car control system. Then, each SA varies its stochastic behavior distributions for adapting to environment in which its policy is evaluated with each passenger waiting times. That is LA which learns the environment autonomously. Using the LA based control technique, the MCE operation efficiency is evaluated through simulation experiments. Results show the technique enables reducing waiting times efficiently, and we confirm the system can adapt to the dynamic environment.

Shielding member for thermonuclear device

Energy Technology Data Exchange (ETDEWEB)

Onozuka, Masanori

1997-06-30

In a thermonuclear device for shielding fast neutrons by shielding members disposed in a shielding vessel (vacuum vessel and structures such as a blanket disposed in the vacuum vessel), the shielding member comprises a large number of shielding wires formed fine and short so as to have elasticity. The shielding wires are sealed in a shielding vessel together with water, and when the width of the shielding vessel is changed, the shielding wires follow after the change of the width while elastically deforming in the shielding vessel, so that great stress and deformation are not formed thereby enabling to improve reliability. In addition, the length, the diameter and the shape of each of the shielding wires can be selected in accordance with the shielding space of the shielding vessel. Even if the shape of the shielding vessel is complicated, the shielding wires can be inserted easily. Accordingly, the filling rate of the shielding members can be changed easily. It can be produced more easily compared with a conventional spherical pebbles. It can be produced more easily than existent spherical shielding pebbles thereby enabling to reduce the production cost. (N.H.)

Elevated temperature design of KALIMER reactor internals accounting for creep and stress-rupture effects

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Yoo, Bong

2000-01-01

In most LMFBR (Liquid Metal Fast Breed Reactor) design, the operating temperature is very high and the time-dependent creep and stress-rupture effects become so important in reactor structural design. Therefore, unlike with conventional PWR, the normal operating conditions can be basically dominant design loading because the hold time at elevated temperature condition is so long and enough to result in severe total creep ratcheting strains during total service lifetime. In this paper, elevated temperature design of the conceptually designed baffle annulus regions of KALIMER (Korea Advanced Liquid Metal Reactor) reactor internal structures is carried out for normal operating conditions which have the operating temperature 530 deg. C and the total service lifetime of 30 years. For the elevated temperature design of reactor internal structures, the ASME Code Case N-201-4 is used. Using this code, the time-dependent stress limits, the accumulated total inelastic strain during service lifetime, and the creep-fatigue damages are evaluated with the calculation results by the elastic analysis under conservative assumptions. The application procedures of elevated temperature design of the reactor internal structures using ASME code case N-201-4 with the elastic analysis method are described step by step in detail. This paper will be useful guide for actual application of elevated temperature design of various reactor types accounting for creep and stress-rupture effects. (author)

Tether Elevator Crawler Systems (TECS)

Science.gov (United States)

Swenson, Frank R.

1987-01-01

One of the needs of the experimenters on the space station is access to steady and controlled-variation microgravity environments. A method of providing these environments is to place the experiment on a tether attached to the space station. This provides a high degree of isolation from structural oscillations and vibrations. Crawlers can move these experiments along the tethers to preferred locations, much like an elevator. This report describes the motion control laws developed for these crawlers and the testing of laboratory models of these tether elevator crawlers.

Cracking in Flexural Reinforced Concrete Members

DEFF Research Database (Denmark)

Rasmussen, Annette Beedholm; Fisker, Jakob; Hagsten, Lars German

2017-01-01

The system of cracks developing in reinforced concrete is in many aspects essential when modelling structures in both serviceability- and ultimate limit state. This paper discusses the behavior concerning crack development in flexural members observed from tests and associates it with two different...... existing models. From the investigations an approach is proposed on how to predict the crack pattern in flexural members involving two different crack systems; primary flexural cracks and local secondary cracks. The results of the approach is in overall good agreement with the observed tests and captures...... the pronounced size effect associated with flexural cracking in which the crack spacing and crack widths are approximately proportional to the depth of the member....

Understanding of advance care planning by family members of persons undergoing hemodialysis.

Science.gov (United States)

Calvin, Amy O; Engebretson, Joan C; Sardual, S Alexander

2014-11-01

The purpose of this qualitative descriptive study was to explore hemodialysis patients' family members' understanding of end-of-life decision-making processes. The project aimed to address (a) family members' constructions of advance care planning (ACP), including their roles and responsibilities, and (b) family members' perceptions of health care providers' roles and responsibilities in ACP. Eighteen family members of persons undergoing hemodialysis were recruited primarily from outpatient dialysis facilities and interviewed individually. Confirmed transcript data were analyzed, coded, and compared, and categories were established. Interpretations were validated throughout the interviews and peer debriefing sessions were used at a later stage in the analysis. The overarching construct identified was one of Protection. Family members protect patients by (a) Sharing Burdens, (b) Normalizing Life, and (c) Personalizing Care. Recommendations for future research include the need to explore ACP of persons undergoing hemodialysis who do not have a family support system. © The Author(s) 2013.

Effects of elevated ozone on CO2 uptake and leaf structure in sugar maple under two light environments

International Nuclear Information System (INIS)

Bäck, J.; Vanderklein, D.W.; Topa, M.A.

1999-01-01

The interactive effects of ozone and light on leaf structure, carbon dioxide uptake and short-term carbon allocation of sugar maple (Acer saccharum Marsh.) seedlings were examined using gas exchange measurements and 14 C-macroautoradiographic techniques. Two-year-old sugar maple seedlings were fumigated from budbreak for 5 months with ambient or 3 × ambient ozone in open-top chambers, receiving either 35% (high light) or 15% (low light) of full sunlight. Ozone accelerated leaf senescence, and reduced net photosynthesis, 14 CO 2 uptake and stomatal conductance, with the effects being most pronounced under low light. The proportion of intercellular space increased in leaves of seedlings grown under elevated ozone and low light, possibly enhancing the susceptibility of mesophyll cells to ozone by increasing the cumulative dose per mesophyll cell. Indeed, damage to spongy mesophyll cells in the elevated ozone × low light treatment was especially frequent. 14 C macroautoradioraphy revealed heterogeneous uptake of 14 CO 2 in well defined areole regions, suggesting patchy stomatal behaviour in all treatments. However, in seedlings grown under elevated ozone and low light, the highest 14 CO 2 uptake occurred along larger veins, while interveinal regions exhibited little or no uptake. Although visible symptoms of ozone injury were not apparent in these seedlings, the cellular damage, reduced photosynthetic rates and reduced whole-leaf chlorophyll levels corroborate the visual scaling of whole-plant senescence, suggesting that the ozone × low light treatment accelerated senescence or senescence-like injury in sugar maple. (author)

Diagnosis of Elevator Faults with LS-SVM Based on Optimization by K-CV

Directory of Open Access Journals (Sweden)

Zhou Wan

2015-01-01

Full Text Available Several common elevator malfunctions were diagnosed with a least square support vector machine (LS-SVM. After acquiring vibration signals of various elevator functions, their energy characteristics and time domain indicators were extracted by theoretically analyzing the optimal wavelet packet, in order to construct a feature vector of malfunctions for identifying causes of the malfunctions as input of LS-SVM. Meanwhile, parameters about LS-SVM were optimized by K-fold cross validation (K-CV. After diagnosing deviated elevator guide rail, deviated shape of guide shoe, abnormal running of tractor, erroneous rope groove of traction sheave, deviated guide wheel, and tension of wire rope, the results suggested that the LS-SVM based on K-CV optimization was one of effective methods for diagnosing elevator malfunctions.

Factors affecting members' evaluation of agri-business ventures' effectiveness.

Science.gov (United States)

Hashemi, Seyyed Mahmoud; Hedjazi, Yousef

2011-02-01

This paper presents work to identify factors affecting effectiveness of agri-business ventures (A-BVs) on the side of providers as perceived by their members. A survey was conducted among 95 members of A-BVs in Zanjan province, Iran. To collect data, a questionnaire was designed. Two distinct groups of A-BVs with low (group 1) and high (group 2) perceived (evaluated) levels of effectiveness were revealed. The study showed that there were significant differences between the two groups on important characteristics of A-BVs and their members. The study also found that there were statistically significant relationships between A-BVs' governance structure and capacity, management and organization characteristics and the perceived effectiveness, whereas there were no statistically significant relationships between A-BVs' advisory methods characteristic applied by members and the perceived effectiveness. Logistic regression results also showed that level of application of rules encouraging members' active participation in important decision makings, clear terms of reference to guide contracting procedures, roles, and responsibilities of parties involved, type of people served and geographical area of program coverage, and members' ability to use Information and Communication Technologies (ICTs) were predictors of the perceived (evaluated) effectiveness of A-BVs. The study showed that evaluation of members of effectiveness of A-BVs would not be the same. It is suggested that Iranian public agricultural extension organization, as responsible organization for monitoring and evaluating services conducted by A-BVs, considered these differences between members with different levels of some important variables. 2010 Elsevier Ltd. All rights reserved.

Elevation-dependent cooling caused by volcanic eruptions during last millennium

Science.gov (United States)

Ning, L.; Liu, J.; Bradley, R. S.; Yan, M.; Sun, W.; Liu, L.

2017-12-01

The amplified warming over the high-elevation regions in recent decades due to the increases of greenhouse gases has attracted lots of attentions, due to the potential severe impacts on mountain hydrological systems and ecosystems and corresponding social and economic influences. Similarly, the model simulations show that the rate of cooling is also amplified with elevation after volcanic eruptions during last millennium, such that high-mountain environments experience larger decreases in temperature than environments at lower elevations. This elevation-dependent cooling (EDC) testifies two important mechanisms, i.e. snow albedo feedback and tropical deep convection mechanism, which also induce the elevation-dependent warming (EDW) found in recent decades due to the increases of greenhouse gases that accelerates the rates of changes in mountain hydrological regimes and ecosystems. It can be concluded that although the influences from natural forcing and anthropogenic forcing on the high-mountain regions are opposite, the mechanisms behind the influences are the same. This finding shows that the temperature change over high-elevation regions is more sensitive to the background climate changes, and needs more attention for adaptations and mitigations due to their bio-diversity and fragile ecosystems.

Elevators or stairs?

Science.gov (United States)

Shah, Sachin; O’Byrne, Michael; Wilson, Merne; Wilson, Thomas

2011-01-01

Background: Staff in hospitals frequently travel between floors and choose between taking the stairs or elevator. We compared the time savings with these two options. Methods: Four people aged 26–67 years completed 14 trips ranging from one to six floors, both ascending and descending. We compared the amount of time per floor travelled by stairs and by two banks of elevators. Participants reported their fatigue levels using a modified Borg scale. We performed two-way analysis of variance to compare the log-transformed data, with participant and time of day as independent variables. Results: The mean time taken to travel between each floor was 13.1 (standard deviation [SD] 1.7) seconds by stairs and 37.5 (SD 19.0) and 35.6 (SD 23.1) seconds by the two elevators (F = 8.61, p elevator equaled about 15 minutes a day. Self-reported fatigue was less than 13 (out of 20) on the Borg scale for all participants, and they all stated that they were able to continue their duties without resting. The extra time associated with elevator use was because of waiting for its arrival. There was a difference in the amount of time taken to travel by elevator depending on the time of day and day of the week. Interpretation: Taking the stairs rather than the elevator saved about 15 minutes each workday. This 3% savings per workday could translate into improved productivity as well as increased fitness. PMID:22159365

Screening for major cardiovascular risk factors among Members of Polish Parliament as a continuation of health marketing for effective cardiovascular prevention in Poland. Warsaw, May 2006.

Science.gov (United States)

Rutkowski, Marcin; Zdrojewski, Tomasz; Bandosz, Piotr; Wierucki, Lukasz; Piwoński, Jerzy; Piwońska, Aleksandra; Narkiewicz, Krzysztof; Opolski, Grzegorz; Drygas, Wojciech; Korewicki, Jerzy; Wyrzykowski, Bogdan

2007-05-01

Cardiovascular diseases are the most common cause of mortality in Poland. To improve the situation in this area, a national cardiovascular preventive project is necessary, and it can be done by close cooperation between medical and political agencies. To present the current epidemiological situation in Poland to political and key opinion leaders and also to assess individual cardiovascular risk among Members of Polish Parliament. The Project was carried out on 23-24 May 2006 in the residence of the Polish Parliament. Anthropometric, blood pressure and cholesterol measurements and a short questionnaire were performed. Survey and educational programme were carried out on 310 out of 460 Members of the Polish Parliament (females 59, males 251). Awareness of one's own blood pressure was declared by 70% of subjects, 39% declared earlier detected arterial hypertension, 21% had new detected elevated blood pressure, 31% declared earlier detected elevated cholesterol level and 32% had new detected elevated cholesterol level. Obesity was found in 40%, smoking was declared by 16.5%. The results were compared with those obtained in corresponding age-groups in the general population. 1. The results of screening survey in the Polish Parliament in 2006 indicate that, in comparison with nationwide adult population and Parliament Members examined in the year of 2000, present Parliament Members are more often diagnosed with obesity. However, they present with a better awareness of their own blood pressure and better control of arterial hypertension, as well as much lower percentage of those who admit smoking cigarettes. 2. Drawing Parliament Members attention to the problem of high prevalence and insufficient control of cardiovascular risk factors should result in positive outcome of future legislation process and make the battle with the epidemic of heart attacks and strokes in Poland more successful.

Explosive welding method for manufacturing ITER-grade 316L(N)/CuCrZr hollow structural member

Energy Technology Data Exchange (ETDEWEB)

Ma, Rui, E-mail: mr9980@163.com [PLA University of Science and Technology, Nanjing 210007 (China); Wang, Yaohua [PLA University of Science and Technology, Nanjing 210007 (China); Wu, Jihong [Southwestern Institute of Physics, Chengdu 610041 (China); Duan, Mianjun [PLA University of Science and Technology, Nanjing 210007 (China)

2014-12-15

Highlights: • Develop a new explosive welding method to fabricate the cooling channel of FW. • Utilize effective energy model to accurately calculate optimal welding parameters. • Provide an efficient way for manufacturing high-ductility hollow structural member. - Abstract: In this study, a new explosive welding method provided an effective way for manufacturing ITER-grade 316L(N)/CuCrZr hollow structural member. The welding parameters (stand-off distance and explosion rate) were calculated respectively using equivalent frontal collision wave model and effective energy model. The welded samples were subject to two step heat treatment cycles (solution annealing and aging). Optical microscopy (OM) and scanning electron microscopy (SEM) were utilized to analyze the microstructure of bonding interface. The mechanical properties of the welded samples were evaluated through microhardness test and tensile test. Moreover, the sealing property of the welded specimens was measured through helium leak test. Microstructural analysis showed that the welded sample using effective energy model had an ideal wavy interface. The results of microhardness test revealed an increase in hardness for both sides near to the bonding interface. And the hardening phenomenon of interface region disappeared after the solution annealing. SEM observation indicated that the samples with the post heat treatments exhibited a ductile fracture with dimple features after tensile test. After the specimens undergo aging strengthening, there was an obvious increase in the strength for all specimens. The helium leak test results have proven that the welded specimens are soundness.

Elevation modulates how Arctic arthropod communities are structured along local environmental gradients

DEFF Research Database (Denmark)

Høye, Toke Thomas; Bowden, Joseph James; Hansen, Oskar Liset Pryds

2017-01-01

The organisation of ecological communities along local environmental gradients provides important information about how such communities may respond to environmental change. In the Arctic, the importance of gradients in shrub cover and soil moisture for non-marine arthropod communities has been...... clearly demonstrated. By replicating studies along shrub and moisture gradients at multiple elevations and using space-for-time substitution, it is possible to examine how arthropod communities may respond to future environmental change. We collected and identified 4640 adult specimens of spiders...... and beetles near Narsarsuaq, South Greenland between 8 July and 25 August, 2014 from 112 pitfall traps. The traps were arranged in eight plots covering local gradients in either soil moisture or tall shrub dominance at both low and high elevation. Multivariate generalized linear models revealed that community...

An elevator for cobalt-60 source

International Nuclear Information System (INIS)

Tang Zaimin; Liang Donghu

1990-07-01

The elevator used for cobalt-60 source is a key device in the irradiation industry. It plays an important role in the safety and control of irradiation operation as well as the utilization rate of radiation source. From 1983 to 1986, Beijing Institute of Nuclear Engineering undertook designing of various size irradiation projects for different uses. Since then a kind of cobalt-60 source elevator suited for the irradiator of wet-source-storage has been chosen. It is reliable in the operation and complete in the function. An automatic control circuit brings the systems of cobalt-60 source elevator into an interlock system which ensures the irradiation operation safety. Besides introducing the structural features and performance of this elevator, the conditions of safety interlocking in raising or lowering the cobalt-60 source is also discussed. The discussion is from the safety viewpoint of operating an irradiator and irradiation technology

Education of ethics committee members: experiences from Croatia.

Science.gov (United States)

Borovecki, A; ten Have, H; Oresković, S

2006-03-01

To study knowledge and attitudes of hospital ethics committee members at the first workshop for ethics committees in Croatia. Before/after cross-sectional study using a self administered questionnaire. Educational workshop for members of hospital ethics committees, Zagreb, 2003. Knowledge and attitudes of participants before and after the workshop; everyday functioning of hospital ethics committees. The majority of the respondents came from committees with at least five members. The majority of ethics committees were appointed by the governing bodies of their hospitals. Most committees were founded after the implementation of the law on health protection in 1997. Membership structure (three physicians and two members from other fields) and functions were established on the basis of that law. Analysis of research protocols was the main part of their work. Other important functions-education, case analysis, guidelines formation-were neglected. Members' level of knowledge was not sufficient for the complicated tasks they were supposed to perform. However, it was significantly higher after the workshop. Most respondents felt their knowledge should be improved by additional education. Their views on certain issues and bioethical dilemmas displayed a high level of paternalism and over protectiveness, which did not change after the workshop. The committees developed according to bureaucratic requirements. Furthermore, there are concerns about members' knowledge levels. More efforts need to be made to use education to improve the quality of the work. Additional research is necessary to explore ethics committees' work in Croatia especially in the hospital setting.

Lunar transportation scenarios utilising the Space Elevator.

Science.gov (United States)

Engel, Kilian A

2005-01-01

The Space Elevator (SE) concept has begun to receive an increasing amount of attention within the space community over the past couple of years and is no longer widely dismissed as pure science fiction. In light of the renewed interest in a, possibly sustained, human presence on the Moon and the fact that transportation and logistics form the bottleneck of many conceivable lunar missions, it is interesting to investigate what role the SE could eventually play in implementing an efficient Earth to Moon transportation system. The elevator allows vehicles to ascend from Earth and be injected into a trans-lunar trajectory without the use of chemical thrusters, thus eliminating gravity loss, aerodynamic loss and the need of high thrust multistage launch systems. Such a system therefore promises substantial savings of propellant and structural mass and could greatly increase the efficiency of Earth to Moon transportation. This paper analyzes different elevator-based trans-lunar transportation scenarios and characterizes them in terms of a number of benchmark figures. The transportation scenarios include direct elevator-launched trans-lunar trajectories, elevator launched trajectories via L1 and L2, as well as launch from an Earth-based elevator and subsequent rendezvous with lunar elevators placed either on the near or on the far side of the Moon. The benchmark figures by which the different transfer options are characterized and evaluated include release radius (RR), required delta v, transfer times as well as other factors such as accessibility of different lunar latitudes, frequency of launch opportunities and mission complexity. The performances of the different lunar transfer options are compared with each other as well as with the performance of conventional mission concepts, represented by Apollo. c2005 Elsevier Ltd. All rights reserved.

Lunar transportation scenarios utilising the Space Elevator

Science.gov (United States)

Engel, Kilian A.

2005-07-01

The Space Elevator (SE) concept has begun to receive an increasing amount of attention within the space community over the past couple of years and is no longer widely dismissed as pure science fiction. In light of the renewed interest in a, possibly sustained, human presence on the Moon and the fact that transportation and logistics form the bottleneck of many conceivable lunar missions, it is interesting to investigate what role the SE could eventually play in implementing an efficient Earth to Moon transportation system. The elevator allows vehicles to ascend from Earth and be injected into a trans-lunar trajectory without the use of chemical thrusters, thus eliminating gravity loss, aerodynamic loss and the need of high thrust multistage launch systems. Such a system therefore promises substantial savings of propellant and structural mass and could greatly increase the efficiency of Earth to Moon transportation. This paper analyzes different elevator-based trans-lunar transportation scenarios and characterizes them in terms of a number of benchmark figures. The transportation scenarios include direct elevator-launched trans-lunar trajectories, elevator-launched trajectories via L1 and L2, as well as launch from an Earth-based elevator and subsequent rendezvous with lunar elevators placed either on the near or on the far side of the Moon. The benchmark figures by which the different transfer options are characterized and evaluated include release radius (RR), required Δv, transfer times as well as other factors such as accessibility of different lunar latitudes, frequency of launch opportunities and mission complexity. The performances of the different lunar transfer options are compared with each other as well as with the performance of conventional mission concepts, represented by Apollo.

Agreement on the privileges and immunities of the Agency. Acceptances by Member States

International Nuclear Information System (INIS)

1995-10-01

The list of Member States shows the 65 Members which, by 30 September 1995, had accepted the Agreement on the Privileges and Immunities of the International Atomic Energy Agency, as provided for in Section 38 thereof

Agreement on the privileges and immunities of the Agency. Acceptances by Member States

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

The list of Member States shows the 65 Members which, by 30 September 1995, had accepted the Agreement on the Privileges and Immunities of the International Atomic Energy Agency, as provided for in Section 38 thereof.

D-Ribulose 5-Phosphate 3-Epimerase: Functional and Structural Relationships to Members of the Ribulose-Phosphate Binding (beta/alpha)8-Barrel Superfamily

International Nuclear Information System (INIS)

Akana, J.; Federov, A.; Federov, E.; Novak, W.; Babbitt, P.; Almo, S.; Gerlt, J.

2006-01-01

The 'ribulose phosphate binding' superfamily defined by the Structural Classification of Proteins (SCOP) database is considered the result of divergent evolution from a common (β/α) 8 -barrel ancestor. The superfamily includes D-ribulose 5-phosphate 3-epimerase (RPE), orotidine 5'-monophosphate decarboxylase (OMPDC), and 3-keto-L-gulonate 6-phosphate decarboxylase (KGPDC), members of the OMPDC suprafamily, as well as enzymes involved in histidine and tryptophan biosynthesis that utilize phosphorylated metabolites as substrates. We now report studies of the functional and structural relationships of RPE to the members of the superfamily. As suggested by the results of crystallographic studies of the RPEs from rice and Plasmodium falciparum, the RPE from Streptococcus pyogenes is activated by Zn 2+ which binds with a stoichiometry of one ion per polypeptide. Although wild type RPE has a high affinity for Zn 2+ and inactive apoenzyme cannot be prepared, the affinity for Zn 2+ is decreased by alanine substitutions for the two histidine residues that coordinate the Zn 2+ ion (H34A and H67A); these mutant proteins can be prepared in an inactive, metal-free form and activated by exogenous Zn 2+ . The crystal structure of the RPE was solved at 1.8 Angstroms resolution in the presence of D-xylitol 5-phosphate, an inert analogue of the D-xylulose 5-phosphate substrate. This structure suggests that the 2,3-enediolate intermediate in the 1,1-proton transfer reaction is stabilized by bidentate coordination to the Zn 2+ that also is liganded to His 34, Asp 36, His 67, and Asp 176; the carboxylate groups of the Asp residues are positioned also to function as the acid/base catalysts. Although the conformation of the bound analogue resembles those of ligands bound in the active sites of OMPDC and KGPDC, the identities of the active site residues that coordinate the essential Zn 2+ and participate as acid/base catalysts are not conserved. We conclude that only the phosphate

D-Ribulose 5-Phosphate 3-Epimerase: Functional and Structural Relationships to Members of the Ribulose-Phosphate Binding (beta/alpha)8-Barrel Superfamily

Energy Technology Data Exchange (ETDEWEB)

Akana,J.; Federov, A.; Federov, E.; Novak, W.; Babbitt, P.; Almo, S.; Gerlt, J.

2006-01-01

The 'ribulose phosphate binding' superfamily defined by the Structural Classification of Proteins (SCOP) database is considered the result of divergent evolution from a common ({beta}/{alpha}){sub 8}-barrel ancestor. The superfamily includes D-ribulose 5-phosphate 3-epimerase (RPE), orotidine 5'-monophosphate decarboxylase (OMPDC), and 3-keto-L-gulonate 6-phosphate decarboxylase (KGPDC), members of the OMPDC suprafamily, as well as enzymes involved in histidine and tryptophan biosynthesis that utilize phosphorylated metabolites as substrates. We now report studies of the functional and structural relationships of RPE to the members of the superfamily. As suggested by the results of crystallographic studies of the RPEs from rice and Plasmodium falciparum, the RPE from Streptococcus pyogenes is activated by Zn{sup 2+} which binds with a stoichiometry of one ion per polypeptide. Although wild type RPE has a high affinity for Zn{sup 2+} and inactive apoenzyme cannot be prepared, the affinity for Zn{sup 2+} is decreased by alanine substitutions for the two histidine residues that coordinate the Zn{sup 2+} ion (H34A and H67A); these mutant proteins can be prepared in an inactive, metal-free form and activated by exogenous Zn{sup 2+}. The crystal structure of the RPE was solved at 1.8 Angstroms resolution in the presence of D-xylitol 5-phosphate, an inert analogue of the D-xylulose 5-phosphate substrate. This structure suggests that the 2,3-enediolate intermediate in the 1,1-proton transfer reaction is stabilized by bidentate coordination to the Zn{sup 2+} that also is liganded to His 34, Asp 36, His 67, and Asp 176; the carboxylate groups of the Asp residues are positioned also to function as the acid/base catalysts. Although the conformation of the bound analogue resembles those of ligands bound in the active sites of OMPDC and KGPDC, the identities of the active site residues that coordinate the essential Zn{sup 2+} and participate as acid/base catalysts

Elevated CO2 stimulates marsh elevation gain, counterbalancing sea-level rise.

Science.gov (United States)

Langley, J Adam; McKee, Karen L; Cahoon, Donald R; Cherry, Julia A; Megonigal, J Patrick

2009-04-14

Tidal wetlands experiencing increased rates of sea-level rise (SLR) must increase rates of soil elevation gain to avoid permanent conversion to open water. The maximal rate of SLR that these ecosystems can tolerate depends partly on mineral sediment deposition, but the accumulation of organic matter is equally important for many wetlands. Plant productivity drives organic matter dynamics and is sensitive to global change factors, such as rising atmospheric CO(2) concentration. It remains unknown how global change will influence organic mechanisms that determine future tidal wetland viability. Here, we present experimental evidence that plant response to elevated atmospheric [CO(2)] stimulates biogenic mechanisms of elevation gain in a brackish marsh. Elevated CO(2) (ambient + 340 ppm) accelerated soil elevation gain by 3.9 mm yr(-1) in this 2-year field study, an effect mediated by stimulation of below-ground plant productivity. Further, a companion greenhouse experiment revealed that the CO(2) effect was enhanced under salinity and flooding conditions likely to accompany future SLR. Our results indicate that by stimulating biogenic contributions to marsh elevation, increases in the greenhouse gas, CO(2), may paradoxically aid some coastal wetlands in counterbalancing rising seas.

Elevated CO2 stimulates marsh elevation gain, counterbalancing sea-level rise

Science.gov (United States)

Langley, J. Adam; McKee, Karen L.; Cahoon, Donald R.; Cherry, Julia A.; Megonigal, J. Patrick

2009-01-01

Tidal wetlands experiencing increased rates of sea-level rise (SLR) must increase rates of soil elevation gain to avoid permanent conversion to open water. The maximal rate of SLR that these ecosystems can tolerate depends partly on mineral sediment deposition, but the accumulation of organic matter is equally important for many wetlands. Plant productivity drives organic matter dynamics and is sensitive to global change factors, such as rising atmospheric CO2 concentration. It remains unknown how global change will influence organic mechanisms that determine future tidal wetland viability. Here, we present experimental evidence that plant response to elevated atmospheric [CO2] stimulates biogenic mechanisms of elevation gain in a brackish marsh. Elevated CO2 (ambient + 340 ppm) accelerated soil elevation gain by 3.9 mm yr−1 in this 2-year field study, an effect mediated by stimulation of below-ground plant productivity. Further, a companion greenhouse experiment revealed that the CO2 effect was enhanced under salinity and flooding conditions likely to accompany future SLR. Our results indicate that by stimulating biogenic contributions to marsh elevation, increases in the greenhouse gas, CO2, may paradoxically aid some coastal wetlands in counterbalancing rising seas. PMID:19325121

Structure and Cancer Immunotherapy of the B7 Family Member B7x

Science.gov (United States)

Jeon, Hyungjun; Vigdorovich, Vladimir; Garrett-Thomson, Sarah C.; Janakiram, Murali; Ramagopal, Udupi A.; Abadi, Yael M.; Lee, Jun Sik; Scandiuzzi, Lisa; Ohaegbulam, Kim C; Chinai, Jordan M; Zhao, Ruihua; Yao, Yu; Mao, Ying; Sparano, Joseph A.; Almo, Steven C.; Zang, Xingxing

2014-01-01

SUMMARY B7x (B7-H4 or B7S1) is a member of the B7 family that can inhibit T cell function. B7x protein is absent in most normal human tissues and immune cells, but is overexpressed in human cancers and often correlates with negative clinical outcome. The expression pattern and function of B7x suggest that it may be a potent immunosuppressive pathway in human cancers. Here we determined the crystal structure of human B7x IgV domain at 1.59Å resolution and mapped the epitopes recognized by monoclonal antibodies. We developed a new in vivo system to screen therapeutic monoclonal antibodies against B7x, and found that the clone 1H3 significantly inhibited growth of B7x-expressing tumor in vivo via multiple mechanisms. Furthermore, the surviving mice given 1H3 treatment were resistant to tumor re-challenge. Our data suggest that targeting B7x on tumors is a promising cancer immunotherapy and humanized 1H3 may be efficacious for immunotherapy of human cancers. PMID:25437562

Structure and Cancer Immunotherapy of the B7 Family Member B7x

Directory of Open Access Journals (Sweden)

Hyungjun Jeon

2014-11-01

Full Text Available B7x (B7-H4 or B7S1 is a member of the B7 family that can inhibit T cell function. B7x protein is absent in most normal human tissues and immune cells, but it is overexpressed in human cancers and often correlates with negative clinical outcome. The expression pattern and function of B7x suggest that it may be a potent immunosuppressive pathway in human cancers. Here, we determined the crystal structure of the human B7x immunoglobulin variable (IgV domain at 1.59 Å resolution and mapped the epitopes recognized by monoclonal antibodies. We developed an in vivo system to screen therapeutic monoclonal antibodies against B7x and found that the clone 1H3 significantly inhibited growth of B7x-expressing tumors in vivo via multiple mechanisms. Furthermore, the surviving mice given 1H3 treatment were resistant to tumor rechallenge. Our data suggest that targeting B7x on tumors is a promising cancer immunotherapy and humanized 1H3 may be efficacious for immunotherapy of human cancers.

Isoenergic modification of whey protein structure by denaturation and crosslinking using transglutaminase

DEFF Research Database (Denmark)

Stender, Emil G. P.; Koutina, Glykeria; Almdal, Kristoffer

2018-01-01

Transglutaminase (TG) catalyzes formation of covalent bonds between lysine and glutamine side chains and has applications in manipulation of food structure. Physical properties of a whey protein mixture (SPC) denatured either at elevated pH or by heat-treatment and followed by TG catalyzed...

Implementation of four layer automatic elevator controller

Science.gov (United States)

Prasad, B. K. V.; Kumar, P. Satish; Charles, B. S.; Srilakshmi, G.

2017-07-01

In this modern era, elevators have become an integral part of any commercial or public complex. It facilitates the faster movement of people and luggage between floors. The lift control system is one among the keenest aspects in electronics controlling module that are used in auto motive filed. Usually elevators are designed for a specific building taking into account the main factors like the measure of the building, the count of persons travelling to each floor and the expected periods of large usage. The lift system was designed with different control strategies. This implementation is based on FPGA, which could be used for any building with any number of floors, with the necessary inputs and outputs. This controller can be implemented based on the required number of floors by merely changing a control variable from the HDL code. This approach is based on an algorithm which reduces the number of computation necessary, on concentrating only on the relevant principles that improves the score and ability of the club of elevator structure. The elevator controller is developed using Verilog HDL and is perfectly executed on a Xilinx ISE 12.4 and Spartan -3E FPGA.

Monolayer structures of alkyl aldehydes: Odd-membered homologues

International Nuclear Information System (INIS)

Phillips, T.K.; Clarke, S.M.; Bhinde, T.; Castro, M.A.; Millan, C.; Medina, S.

2011-01-01

Crystalline monolayers of three aldehydes with an odd number of carbon atoms in the alkyl chain (C 7 , C 9 and C 11 ) at low coverages are observed by a combination of X-ray and neutron diffraction. Analysis of the diffraction data is discussed and possible monolayer crystal structures are proposed; although unique structures could not be ascertained for all molecules. We conclude that the structures are flat on the surface, with the molecules lying in the plane of the layer. The C 11 homologue is determined to have a plane group of either p2, pgb or pgg, and for the C 7 homologue the p2 plane group is preferred.

Reducing elevator energy use: A comparison of posted feedback and reduced elevator convenience

Science.gov (United States)

Houten, Ron Van; Nau, Paul A.; Merrigan, Michael

1981-01-01

The effects of two different procedures for reducing elevator energy use were assessed using a multiple-baseline design. In the first procedure, feedback about the amount of energy consumed by the elevators each week was posted on each elevator door. Later, signs advocating the use of stairs to save energy and improve health were posted next to the feedback signs. In the second procedure, the time required to travel between floors was increased by adding a delay to the elevator door closing mechanisms. Results indicated that neither feedback alone nor feedback plus educational signs reduced the amount of energy consumed by the elevators. However, use of the door delay reduced consumption by one-third in all elevators. A second experiment replicated the effect of the door delay on energy consumption and, in addition, demonstrated that the door delay also produced a reduction in the number of persons using the elevator. The second experiment also showed that, following an initial period during which a full delay was in effect, a gradual reduction of the delay interval resulted in continued energy conservation. Reduced convenience as a general strategy for energy conservation is discussed. PMID:16795648

Coping with stigma by association and family burden among family members of people with mental illness.

Science.gov (United States)

van der Sanden, Remko L M; Stutterheim, Sarah E; Pryor, John B; Kok, Gerjo; Bos, Arjan E R

2014-10-01

In this study, we explored stigma by association, family burden, and their impact on the family members of people with mental illness. We also studied the ways in which family members coped with these phenomena. We conducted semistructured interviews with 23 immediate family members of people with mental illness. Participants reported various experiences of stigma by association and family burden. Social exclusion, being blamed, not being taken seriously, time-consuming caregiving activities, and exhaustion appeared to be the predominant forms of stigma by association and family burden experienced by the participants. The participants used problem-focused and emotion-focused coping strategies, separately or simultaneously, to cope with the negative impact of stigma by association and family burden. The results suggest that family members should have access to services to address these problems. Social, instrumental, and emotional support should be given to family members by community members and mental health professionals.

Involvement of Smad3 pathway in atrial fibrosis induced by elevated hydrostatic pressure.

Science.gov (United States)

Wei, Wei; Rao, Fang; Liu, Fangzhou; Xue, Yumei; Deng, Chunyu; Wang, Zhaoyu; Zhu, Jiening; Yang, Hui; Li, Xin; Zhang, Mengzhen; Fu, Yongheng; Zhu, Wensi; Shan, Zhixin; Wu, Shulin

2018-06-01

Hypertension is a main risk factor for atrial fibrillation, but the direct effects of hydrostatic pressure on the atrial fibrosis are still unknown. The present study investigated whether hydrostatic pressure is responsible for atrial fibrosis, and addressed a potential role of the Smad pathway in this pathology. Biochemical assays were used to study regulation and expression of fibrotic factors in spontaneously hypertensive rats (SHRs) and Wistar rats, and in cardiac fibroblasts (CFs) cultured under standard (0 mmHg) and elevated (20, 40 mmHg) hydrostatic pressure. Levels of atrial fibrosis and protein expression of fibrotic factors Col-1A1/-3A1, TGF-β1, and MMP-2 in SHRs' left atrial tissues were higher than those in Wistar rats. Exposure to elevated pressure was associated with the proliferation of CFs. The protein expression of Col-1A1/-3A1, TGF-β1, and MMP-2 in CFs was also up-regulated in a pressure-dependent manner. The proliferation of CFs and increased expressions of fibrotic markers induced by elevated hydrostatic pressure could be reversed by the Smad3 inhibitor naringenin. The activation of Smad3 pathway was also stimulated by elevated hydrostatic pressure. These results demonstrate that CF secretory function and proliferation can be up-regulated by exposure to elevated pressure, and that Smad3 may modulate CF activation induced by high hydrostatic pressure. © 2017 Wiley Periodicals, Inc.

Is guava phenolic metabolism influenced by elevated atmospheric CO2?

Science.gov (United States)

Mendes de Rezende, Fernanda; Pereira de Souza, Amanda; Silveira Buckeridge, Marcos; Maria Furlan, Cláudia

2015-01-01

Seedlings of Psidium guajava cv. Pedro Sato were distributed into four open-top chambers: two with ambient CO(2) (∼390 ppm) and two with elevated CO(2) (∼780 ppm). Monthly, five individuals of each chamber were collected, separated into root, stem and leaves and immediately frozen in liquid nitrogen. Chemical parameters were analyzed to investigate how guava invests the surplus carbon. For all classes of phenolic compounds analyzed only tannins showed significant increase in plants at elevated CO(2) after 90 days. There was no significant difference in dry biomass, but the leaves showed high accumulation of starch under elevated CO(2). Results suggest that elevated CO(2) seems to be favorable to seedlings of P. guajava, due to accumulation of starch and tannins, the latter being an important anti-herbivore substance. Copyright © 2014 Elsevier Ltd. All rights reserved.

Recent advances in the field of 16-membered macrolide antibiotics.

Science.gov (United States)

Cui, W; Ma, S

2011-10-01

The continuing emergence of bacterial resistance has provided an incentive for recent intensified research on macrolide antibiotics. Belonging to the macrolide family, 16-membered macrolides also experience a renewed interest in further exploration. The medicinal potential of 16-membered macrolides in search for new antibacterials stems from some advantages over 14-membered macrolides, such as gastrointestinal tolerability, structural flexibility, and lack of inducible resistance. Thus, compared with abundant articles on various 14-membered macrolide derivatives in the literature, this review will highlight some representative 16-membered macrolide antibiotics and their recently discovered analogs. Furthermore, the action and resistance mechanisms of 16-membered macrolide antibiotics will be elucidated as well to assist the drug design.

TEACHING IN ONLINE COURSES: Experiences of Instructional Technology Faculty Members

Directory of Open Access Journals (Sweden)

Omur AKDEMIR

2008-04-01

Full Text Available The Internet and computer technology have altered the education landscape. Online courses are offered throughout the world. Learning about the experiences of faculty members is important to guide practitioners and administrators. Using qualitative research methodology, this study investigated the experiences of faculty members teaching online courses. A convenience sampling was used to select the instructional technology faculty members to investigate their experiences in online courses. Semi-structured interviews with faculty members teaching online courses were used as the primary source to collect data about the experiences of faculty members in online courses. Results of the study showed that faculty members' interest in using technology and the amount of time available to them for online course design affected the quality of online courses. The findings of this study also indicated that design quality of online courses is affected by the interest of faculty members to use the technology and the time that they can devote to planning, designing, and developing online courses. The poor design of existing online courses, high learning expectations of ndividuals from these courses, and the future of online courses are the concerns of faculty members. Higher education institutions should support workshops and trainings to increase the skills and interests of non-instructional design faculty members to design and develop online courses.

Personality Disorder Traits During Adolescence and Relationships with Family Members During the Transition to Adulthood

Science.gov (United States)

Johnson, Jeffrey G.; Chen, Henian; Cohen, Patricia

2004-01-01

Data from the Children in the Community Transitions Study, a prospective longitudinal investigation, were used to examine the association between adolescent personality disorder (PD) traits and conflict with family members during the transition to adulthood. PD traits at mean age 16 years were associated with elevated contact and conflict with…

Elevational patterns of genetic variation in the cosmopolitan moss Bryum argenteum (Bryaceae).

Science.gov (United States)

Pisa, Sergio; Werner, Olaf; Vanderpoorten, Alain; Magdy, Mahmoud; Ros, Rosa M

2013-10-01

The Baas Becking tenet posits that 'everything is everywhere, but the environment selects' to explain cosmopolitan distributions in highly vagile taxa. Bryophyte species show wider distributions than vascular plants and include examples of truly cosmopolitan ranges, which have been interpreted as a result of high dispersal capacities and ecological plasticity. In the current study, we documented patterns of genetic structure and diversity in the cosmopolitan moss Bryum argenteum along an elevational gradient to determine if genetic diversity and structure is homogenized by intense migrations in the lack of ecological differentiation. • 60 specimens were collected in the Sierra Nevada Mountains (Spain) between 100 and 2870 m and sequenced for ITS and rps4. Comparative analyses, genetic diversity estimators, and Mantel's tests were employed to determine the relationship between genetic variation, elevation, and geographic distance and to look for signs of demographic shifts. • Genetic diversity peaked above 1900 m and no signs of demographic shifts were detected at any elevation. There was a strong phylogenetic component in elevational variation. Genetic variation was significantly correlated with elevation, but not with geographic distance. • The results point to the long-term persistence of Bryum argenteum in a range that was glaciated during the Late Pleistocene. Evidence for an environmentally driven pattern of genetic differentiation suggests adaptive divergence. This supports the Baas Becking tenet and indicates that ecological specialization might play a key role in explaining patterns of genetic structure in cosmopolitan mosses.

Technology Development and Demonstration Concepts for the Space Elevator

Science.gov (United States)

Smitherman, David V., Jr.

2004-01-01

During the 1990s several discoveries and advances in the development of carbon nano-tube (CNT) materials indicated that material strengths many times greater than common high-strength composite materials might be possible. Progress in the development of this material led to renewed interest in the space elevator concept for construction of a tether structure from the surface of the Earth through a geostationary orbit (GEO) and thus creating a new approach to Earth-to-orbit transportation infrastructures. To investigate this possibility the author, in 1999, managed for NASA a space elevator work:hop at the Marshall Space Flight Center to explore the potential feasibility of space elevators in the 21 century, and to identify the critical technologies and demonstration missions needed to make development of space elevators feasible. Since that time, a NASA Institute for Advanced Concepts (NIAC) funded study of the Space Elevator proposed a concept for a simpler first space elevator system using more near-term technologies. This paper will review some of the latest ideas for space elevator development, the critical technologies required, and some of the ideas proposed for demonstrating the feasibility for full-scale development of an Earth to GEO space elevator. Critical technologies include CNT composite materials, wireless power transmission, orbital object avoidance, and large-scale tether deployment and control systems. Numerous paths for technology demonstrations have been proposed utilizing ground experiments, air structures. LEO missions, the space shuttle, the international Space Station, GEO demonstration missions, demonstrations at the lunar L1 or L2 points, and other locations. In conclusion, this paper finds that the most critical technologies for an Earth to GEO space elevator include CNT composite materials development and object avoidance technologies; that lack of successful development of these technologies need not preclude continued development of

Bucket elevator type continuous unloader; Basket elevator gata renzokushiki anroda

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-04-20

This unloader was delivered to Wakayama branch of Sumikin Butsuryu in the site of Wakayama steel plant of Sumitomo Metal Industries Ltd. for landing sub-materials for ironworks. Main specifications: (1) Capacity: 400t/h for limestone, 280t/h for gypsum, (2) Kinds of ships: 5,000DWT maximum, (3) Boom swing radius: 20m. Features: (1) Simple light-weight unloader for not large ships for main materials but small coastal service ships which works with not swing motion but only traveling and normal-directional motion of the under structure of a bucket elevator unit, (2) Various useful functions such as ground conveyance, truck loading, back yard stacking and back yard shipment for handling of various sub-materials. (translated by NEDO)

An audit of clinical service examining the uptake of genetic testing by at-risk family members.

Science.gov (United States)

Forrest, Laura; Delatycki, Martin; Curnow, Lisette; Gen Couns, M; Skene, Loane; Aitken, Maryanne

2012-01-01

The aim of this study was to investigate the uptake of genetic testing by at-risk family members for four genetic conditions: chromosomal translocations, fragile X syndrome, Huntington disease, and spinal muscular atrophy. A clinical audit was undertaken using genetics files from Genetic Health Services Victoria. Data were extracted from the files regarding the number of at-risk family members and the proportion tested. Information was also collected about whether discussion of at-risk family members and family communication during the genetic consultation was recorded. The proportion of at-risk family members who had genetic testing ranged from 11% to 18%. First-degree family members were most frequently tested and the proportion of testing decreased by degree of relatedness to the proband. Smaller families were significantly more likely to have genetic testing for all conditions except Huntington disease. Female at-risk family members were significantly more likely to have testing for fragile X syndrome. The majority of at-risk family members do not have genetic testing. Family communication is likely to influence the uptake of genetic testing by at-risk family members and therefore it is important that families are supported while communicating to ensure that at-risk family members are able to make informed decisions about genetic testing.

Compensation for Those Indirectly Affected by the Death of a Household Member

Directory of Open Access Journals (Sweden)

Jędrzychowska Anna

2017-12-01

Full Text Available This article demonstrates the size of the budget gap that arises in a household after the death of that member who was the breadwinner of the family. It also describes how this gap can be covered by motor vehicle liability insurance. One source of funding for this gap could be, for example, an annuity for indirect victims. In many EU countries, people who are members of the household of the deceased are considered to be affected as a result of his death. Those indirectly affected will include the family members and relatives of the deceased (spouse, parent, child, sibling, and cohabitant. The person responsible for the death should pay compensation to the family members of the deceased. One of the elements determining this compensation should be the loss of income to the family of the deceased. The second element is compensation for the lost personal contribution. This paper presents the study of literature as an introduction to the relevant issues. The problem of compensation for lost income will be illustrated by legal regulations and calculations based on the account actuarial-term annuity. The study focuses on the selected EU countries. This article is part of a broader study by the author on the material consequences of personal injury and sources of their financing.

Agreement on the privileges and immunities of the Agency: Acceptances by Member States

International Nuclear Information System (INIS)

1989-10-01

The document lists the 61 Member States which, by 1 October 1989, had accepted the Agreement on the Privileges and Immunities of the International Atomic Energy Agency, as provided for in Section 38 thereof. The list is followed by the texts of such reservations to the Agreement as some of the Members in question made when depositing their respective instruments of acceptance with the Director General

Specific Features of Structural-Phase State and Properties of Reactor Pressure Vessel Steel at Elevated Irradiation Temperature

Directory of Open Access Journals (Sweden)

E. A. Kuleshova

2017-01-01

Full Text Available This paper considers influence of elevated irradiation temperature on structure and properties of 15Kh2NMFAA reactor pressure vessel (RPV steel. The steel is investigated after accelerated irradiation at 300°C (operating temperature of VVER-1000-type RPV and 400°C supposed to be the operating temperature of advanced RPVs. Irradiation at 300°C leads to formation of radiation-induced precipitates and radiation defects-dislocation loops, while no carbide phase transformation is observed. Irradiation at a higher temperature (400°C neither causes formation of radiation-induced precipitates nor provides formation of dislocation loops, but it does increase the number density of the main initial hardening phase—of the carbonitrides. Increase of phosphorus concentration in grain boundaries is more pronounced for irradiation at 400°C as compared to irradiation at 300°C due to influence of thermally enhanced diffusion at a higher temperature. The structural-phase changes determine the changes of mechanical properties: at both irradiation temperatures irradiation embrittlement is mainly due to the hardening mechanism with some contribution of the nonhardening one for irradiation at 400°C. Lack of formation of radiation-induced precipitates at T = 400°C provides a small ΔTK shift (17°C. The obtained results demonstrate that the investigated 15Kh2NMFAA steel may be a promising material for advanced reactors with an elevated operating temperature.

46 CFR 72.05-20 - Stairways, ladders, and elevators.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Stairways, ladders, and elevators. 72.05-20 Section 72.05-20 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PASSENGER VESSELS CONSTRUCTION AND ARRANGEMENT Structural Fire Protection § 72.05-20 Stairways, ladders, and elevators. (a)(1) Except as further noted the provisions of this...

Actuator assembly including a single axis of rotation locking member

Science.gov (United States)

Quitmeyer, James N.; Benson, Dwayne M.; Geck, Kellan P.

2009-12-08

An actuator assembly including an actuator housing assembly and a single axis of rotation locking member fixedly attached to a portion of the actuator housing assembly and an external mounting structure. The single axis of rotation locking member restricting rotational movement of the actuator housing assembly about at least one axis. The single axis of rotation locking member is coupled at a first end to the actuator housing assembly about a Y axis and at a 90.degree. angle to an X and Z axis providing rotation of the actuator housing assembly about the Y axis. The single axis of rotation locking member is coupled at a second end to a mounting structure, and more particularly a mounting pin, about an X axis and at a 90.degree. angle to a Y and Z axis providing rotation of the actuator housing assembly about the X axis. The actuator assembly is thereby restricted from rotation about the Z axis.

Spirituality and job satisfaction among hospice interdisciplinary team members.

Science.gov (United States)

Clark, Leah; Leedy, Stephen; McDonald, Laurie; Muller, Barbara; Lamb, Cheryl; Mendez, Tracy; Kim, Sehwan; Schonwetter, Ronald

2007-12-01

As a continuing effort to enhance the quality of palliative care for the dying, this study examined (1) the prevalence of spirituality among hospice interdisciplinary team (IDT) members; (2) whether spirituality is related to job satisfaction; and (3) the structural path relationships among four variables: spiritual belief, integration of spirituality at work, self actualization and job satisfaction. The study surveyed 215 hospice IDT members who completed the Jarel Spiritual Well-Being Scale, the Chamiec-Case Spirituality Integration and Job Satisfaction Scales. Multiple regression and structural path modeling methods were applied to explain the path relationships involving all four variables. The IDT members surveyed were: nurses, 46.4%; home health aids, 24.9%; social workers, 17.4%; chaplains, 4.2%; physicians, 2.3%; and other, 4.8%. Ninety-eight percent of the respondents viewed themselves as having spiritual well-being. On a 0-100 scale, IDT staff reported high spiritual belief (mean = 89.4) and they were self-actualizing (mean = 82.6). Most reported high job satisfaction (mean = 79.3) and spiritual integration (mean = 67.9). In multiple regression, spirituality, integration and self-actualization explained 22% of the variation in job satisfaction (R = 0.48; adjusted R(2) = 0.218; df = 3,175; F = 17.2; p = 0.001). Structural path models revealed that job satisfaction is more likely to be realized by a model that transforms one's spirituality into processes of integrating spirituality at work and self actualization (chi(2) = 0.614; df = 1; p = 0.433) than a model that establishes a direct path from spirituality to job satisfaction (chi(2) = 1.65; df = 1; p = 0.199). Hospice IDT member's integration of their spirituality at work and greater self actualization significantly improve job satisfaction.

Structure of Escherichia coli RutC, a member of the YjgF family and putative aminoacrylate peracid reductase of the rut operon

International Nuclear Information System (INIS)

Knapik, Aleksandra Alicja; Petkowski, Janusz Jurand; Otwinowski, Zbyszek; Cymborowski, Marcin Tadeusz; Cooper, David Robert; Chruszcz, Maksymilian; Krajewska, Wanda Małgorzata; Minor, Wladek

2012-01-01

The structure of the putative aminoacrylate peracid reductase RutC of the rut operon, a member of the YjgF family, is reported. RutC is the third enzyme in the Escherichia coli rut pathway of uracil degradation. RutC belongs to the highly conserved YjgF family of proteins. The structure of the RutC protein was determined and refined to 1.95 Å resolution. The crystal belonged to space group P2 1 2 1 2 and contained six molecules in the asymmetric unit. The structure was solved by SAD phasing and was refined to an R work of 19.3% (R free = 21.7%). The final model revealed that this protein has a Bacillus chorismate mutase-like fold and forms a homotrimer with a hydrophobic cavity in the center of the structure and ligand-binding clefts between two subunits. A likely function for RutC is the reduction of peroxy-aminoacrylate to aminoacrylate as a part of a detoxification process

A survey of family members' satisfaction with the services provided by hospice palliative care volunteers.

Science.gov (United States)

Claxton-Oldfield, Stephen; Gosselin, Natasha; Schmidt-Chamberlain, Kirsten; Claxton-Oldfield, Jane

2010-05-01

A total of 22 family members, whose deceased loved ones had used the services of a hospice palliative care volunteer, responded to a brief survey designed to assess the importance of the different kinds of support offered to them (family members) by the volunteer, their impressions of the volunteers' personal qualities/characteristics, their general experiences with the volunteer, and their overall satisfaction with the volunteer services. The kind of support that received the highest importance rating from family members was the opportunity to take a much-needed break from the demands of caring for their loved one, closely followed by emotional support, the volunteer spending time with them, and the volunteer providing them with information. Family members rated volunteers highly on a list of qualities/characteristics that exemplify individuals who are effective in this role. In all, 85% of the family members felt that their volunteer was well trained and 95% did not feel that their or their loved one's privacy had been invaded by having a volunteer. Overall, family members were very satisfied with the volunteer support they received. Some limitations of the study are discussed.

CE: Military Sexual Trauma in Male Service Members.

Science.gov (United States)

Eckerlin, Denise M; Kovalesky, Andrea; Jakupcak, Matthew

2016-09-01

: The experience of military sexual trauma (MST), which can result from assault, battery, or harassment of a sexual nature, may jeopardize the mental health of service members as well as that of their family members, colleagues, and community members. Although a greater proportion of female than male service members are subjected to MST, the Department of Defense estimates that the absolute numbers of affected men and women, across all ranks and branches of military service, are nearly equal because roughly 85% of military members are men. Little research has explored the effects of MST on men. This article discusses the unique ways in which men may experience MST, and examines how social stereotypes of masculinity, myths surrounding sexual assault, and military culture and structure often influence a man's interpretation of an attack and his likelihood of reporting the incident or seeking treatment. It describes current treatments for MST-related mental health conditions and addresses implications for nurses and other health care professionals.

Immunoglobulin superfamily members encoded by viruses and their multiple roles in immune evasion.

Science.gov (United States)

Farré, Domènec; Martínez-Vicente, Pablo; Engel, Pablo; Angulo, Ana

2017-05-01

Pathogens have developed a plethora of strategies to undermine host immune defenses in order to guarantee their survival. For large DNA viruses, these immune evasion mechanisms frequently rely on the expression of genes acquired from host genomes. Horizontally transferred genes include members of the immunoglobulin superfamily, whose products constitute the most diverse group of proteins of vertebrate genomes. Their promiscuous immunoglobulin domains, which comprise the building blocks of these molecules, are involved in a large variety of functions mediated by ligand-binding interactions. The flexible structural nature of the immunoglobulin domains makes them appealing targets for viral capture due to their capacity to generate high functional diversity. Here, we present an up-to-date review of immunoglobulin superfamily gene homologs encoded by herpesviruses, poxviruses, and adenoviruses, that include CD200, CD47, Fc receptors, interleukin-1 receptor 2, interleukin-18 binding protein, CD80, carcinoembryonic antigen-related cell adhesion molecules, and signaling lymphocyte activation molecules. We discuss their distinct structural attributes, binding properties, and functions, shaped by evolutionary pressures to disarm specific immune pathways. We include several novel genes identified from extensive genome database surveys. An understanding of the properties and modes of action of these viral proteins may guide the development of novel immune-modulatory therapeutic tools. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The 1.8-Å resolution crystal structure of YDR533Cp from Saccharomyces cerevisiae: A member of the DJ-1/ThiJ/PfpI superfamily

Science.gov (United States)

Wilson, Mark A.; Amour, Courtney V. St.; Collins, Jennifer L.; Ringe, Dagmar; Petsko, Gregory A.

2004-01-01

The yeast gene YDR533C encodes a protein belonging to the DJ-1/ThiJ/PfpI superfamily. This family includes the human protein DJ-1, which is mutated in autosomal recessive early-onset Parkinson's disease. The function of DJ-1 and its yeast homologue YDR533Cp is unknown. We report here the crystal structure of YDR533Cp at 1.8-Å resolution. The structure indicates that the closest relative to YDR533Cp is the Escherichia coli heat shock protein Hsp31 (YedU), which has both chaperone and protease activity. As expected, the overall fold of the core domain of YDR533Cp is also similar to that of DJ-1 and the bacterial protease PfpI. YDR533Cp contains a possible catalytic triad analogous to that of Hsp31 and an additional domain that is present in Hsp31 but is not seen in DJ-1 and other members of the family. The cysteine in this triad (Cys-138) is oxidized in this crystal structure, similar to modifications seen in the corresponding cysteine in the crystal structure of DJ-1. YDR533Cp appears to be a dimer both in solution and the crystal, but this dimer is formed by a different interface than that found in Hsp31 or other members of the superfamily. PMID:14745011

31 CFR 215.9 - Change of legal residence by members of the Armed Forces.

Science.gov (United States)

2010-07-01

... legal residence. The notification shall include the name, social security number, current mailing... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Change of legal residence by members... Withholding Agreement § 215.9 Change of legal residence by members of the Armed Forces. (a) In determining the...

Sequence and structural characterization of great salt lake bacteriophage CW02, a member of the T7-like supergroup.

Science.gov (United States)

Shen, Peter S; Domek, Matthew J; Sanz-García, Eduardo; Makaju, Aman; Taylor, Ryan M; Hoggan, Ryan; Culumber, Michele D; Oberg, Craig J; Breakwell, Donald P; Prince, John T; Belnap, David M

2012-08-01

Halophage CW02 infects a Salinivibrio costicola-like bacterium, SA50, isolated from the Great Salt Lake. Following isolation, cultivation, and purification, CW02 was characterized by DNA sequencing, mass spectrometry, and electron microscopy. A conserved module of structural genes places CW02 in the T7 supergroup, members of which are found in diverse aquatic environments, including marine and freshwater ecosystems. CW02 has morphological similarities to viruses of the Podoviridae family. The structure of CW02, solved by cryogenic electron microscopy and three-dimensional reconstruction, enabled the fitting of a portion of the bacteriophage HK97 capsid protein into CW02 capsid density, thereby providing additional evidence that capsid proteins of tailed double-stranded DNA phages have a conserved fold. The CW02 capsid consists of bacteriophage lambda gpD-like densities that likely contribute to particle stability. Turret-like densities were found on icosahedral vertices and may represent a unique adaptation similar to what has been seen in other extremophilic viruses that infect archaea, such as Sulfolobus turreted icosahedral virus and halophage SH1.

Study on predicting residual life of elevator links by fracture mechanics approach

Energy Technology Data Exchange (ETDEWEB)

Li Helin; Zhang Yi; Deng Zengjie [China National Petroleum Corp., Xi`an, Shaanxi (China). Tubular Goods Research Center; Jin Dazeng [Xi`an Jiaotong Univ., Xi`an, Shaanxi (China)

1995-12-31

On the basis of investigation, failure and fracture analysis of elevator links, residual life prediction of links using fracture mechanics approach is studied, and mechanical properties, fracture toughness value K{sub IC} and fatigue crack propagation rage da/dN of the steel for elevator links are determined. Using the relation between stress intensity factor K{sub I} and the strain-energy release rate, the two-dimensional conversion thickness finite element method has been used to calculate the stress intensity factors K{sub I} for dangerous sections in the ring part of links. Furthermore, the reliability of calculations of the finite element stress intensity factors K{sub I} for dangerous sections of elevator links and the residual life computation for links are verified by fatigue tests of actual links. Finally, the experimental verification of computed results by 150T link fractured at site indicates that the computed critical crack lengths and residual life tally well with those measured and meet the needs of oil drilling.

Experiences of Academic Members About their Professional Challenges: a Content Analysis Qualitative study.

Science.gov (United States)

Shahhosseini, Zohreh; Danesh, Mahmonier

2014-04-01

University faculty members of different disciplines in any country, by giving better quality services, will further accelerate the development of their respective countries. This study aims to explore the experiences of faculty members about their professional challenges. In this qualitative study, which was conducted in 2013, fifteen faculty members in the departments of clinical and basic sciences of Mazandaran university of Medical Sciences in northern Iran were chosen for semi-structured in-depth interviews by purposive sampling method. All tape-recorded data were fully transcribed and content analysis was performed. AFTER IMMERSION AND DATA ANALYSIS, THREE MAIN THEMES WERE EMERGED INCLUDING: "Imbalances in academic members' tasks in different areas", "Weakness of evaluation and promotion system" and "Failure to provide the infrastructure educational facilities". The main themes and sub-themes are explained by the help of participants' direct quotations. This study suggested that it is better to take effective measures to improve the faculty members' situation and therefore increase their efficiency, effectiveness and productivity.

National Elevation Dataset

Science.gov (United States)

,

2002-01-01

The National Elevation Dataset (NED) is a new raster product assembled by the U.S. Geological Survey. NED is designed to provide National elevation data in a seamless form with a consistent datum, elevation unit, and projection. Data corrections were made in the NED assembly process to minimize artifacts, perform edge matching, and fill sliver areas of missing data. NED has a resolution of one arc-second (approximately 30 meters) for the conterminous United States, Hawaii, Puerto Rico and the island territories and a resolution of two arc-seconds for Alaska. NED data sources have a variety of elevation units, horizontal datums, and map projections. In the NED assembly process the elevation values are converted to decimal meters as a consistent unit of measure, NAD83 is consistently used as horizontal datum, and all the data are recast in a geographic projection. Older DEM's produced by methods that are now obsolete have been filtered during the NED assembly process to minimize artifacts that are commonly found in data produced by these methods. Artifact removal greatly improves the quality of the slope, shaded-relief, and synthetic drainage information that can be derived from the elevation data. Figure 2 illustrates the results of this artifact removal filtering. NED processing also includes steps to adjust values where adjacent DEM's do not match well, and to fill sliver areas of missing data between DEM's. These processing steps ensure that NED has no void areas and artificial discontinuities have been minimized. The artifact removal filtering process does not eliminate all of the artifacts. In areas where the only available DEM is produced by older methods, then "striping" may still occur.

The members of the Agency

International Nuclear Information System (INIS)

1996-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.46) is Bosnia and Herzegovina. The Attachment hereto shows the dates on which the present 123 Member States became Members. It also shows the States whose applications for membership of the Agency have been approved by the General Conference but which have not yet deposited an instrument of acceptance of the Statute and the State whose application for membership has been recommended by the Board of Governors for approval by the General Conference

The Members of the Agency

International Nuclear Information System (INIS)

1995-01-01

No new Member has joined the Agency since the last list of Member States was issued (INFCIRC/2/Rev.45). The Attachment hereto shows the dates on which the present 122 Member States became Members. It also shows the State whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States whose applications for membership have been recommended by the Board of Governors for approval by the General Conference

The Members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-11

No new Member has joined the Agency since the last list of Member States was issued (INFCIRC/2/Rev.45). The Attachment hereto shows the dates on which the present 122 Member States became Members. It also shows the State whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States whose applications for membership have been recommended by the Board of Governors for approval by the General Conference.

The members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-26

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.46) is Bosnia and Herzegovina. The Attachment hereto shows the dates on which the present 123 Member States became Members. It also shows the States whose applications for membership of the Agency have been approved by the General Conference but which have not yet deposited an instrument of acceptance of the Statute and the State whose application for membership has been recommended by the Board of Governors for approval by the General Conference.

An Uncharacterized Member of the Ribokinase Family in Thermococcus kodakarensis Exhibits myo-Inositol Kinase Activity*

Science.gov (United States)

Sato, Takaaki; Fujihashi, Masahiro; Miyamoto, Yukika; Kuwata, Keiko; Kusaka, Eriko; Fujita, Haruo; Miki, Kunio; Atomi, Haruyuki

2013-01-01

Here we performed structural and biochemical analyses on the TK2285 gene product, an uncharacterized protein annotated as a member of the ribokinase family, from the hyperthermophilic archaeon Thermococcus kodakarensis. The three-dimensional structure of the TK2285 protein resembled those of previously characterized members of the ribokinase family including ribokinase, adenosine kinase, and phosphofructokinase. Conserved residues characteristic of this protein family were located in a cleft of the TK2285 protein as in other members whose structures have been determined. We thus examined the kinase activity of the TK2285 protein toward various sugars recognized by well characterized ribokinase family members. Although activity with sugar phosphates and nucleosides was not detected, kinase activity was observed toward d-allose, d-lyxose, d-tagatose, d-talose, d-xylose, and d-xylulose. Kinetic analyses with the six sugar substrates revealed high Km values, suggesting that they were not the true physiological substrates. By examining activity toward amino sugars, sugar alcohols, and disaccharides, we found that the TK2285 protein exhibited prominent kinase activity toward myo-inositol. Kinetic analyses with myo-inositol revealed a greater kcat and much lower Km value than those obtained with the monosaccharides, resulting in over a 2,000-fold increase in kcat/Km values. TK2285 homologs are distributed among members of Thermococcales, and in most species, the gene is positioned close to a myo-inositol monophosphate synthase gene. Our results suggest the presence of a novel subfamily of the ribokinase family whose members are present in Archaea and recognize myo-inositol as a substrate. PMID:23737529

Self-esteem and in-group bias among members of a religious social category.

Science.gov (United States)

Hunter, J A

2001-06-01

In a sample of New Zealand university students, the author extended earlier research into the relationship between self-esteem and intergroup discrimination. He found no support for the hypothesis that social-category members (i.e., Christians) experience an elevation in the domain of self-esteem (i.e., religious self-esteem) judged as more relevant to the in-group after evaluations favoring the in-group. Regardless of whether the evaluation targets behaved positively or negatively, the respondents in the experimental condition evaluated in-group (Christian) targets more highly than out-group (Atheist) targets. After evaluations favoring the in-group, the respondents did not experience an elevation of religious self-esteem, global self-esteem, or mathematical self-esteem (judged as less relevant to the in-group).

Elevator and hydraulics; Elevator to yuatsu

Energy Technology Data Exchange (ETDEWEB)

Nakamura, I. [Hitachi, Ltd., Tokyo (Japan)

1994-07-15

A hydraulic type elevator is installed in relatively lower buildings as compared with a rope type elevator, but the ratio in the number of installation of the former elevator is increasing. This paper explains from its construction and features to especially various control systems for the riding comfort and safety. A direct push-up system with hydraulic jacks arranged beneath a car, and an indirect push-up system that has hydraulic jacks arranged on flank of a car and transmits the movement of a plunger via a rope are available. The latter system eliminates the need of large holes to embed hydraulic jacks. While the speed is controlled by controlling flow rates of high-pressure oil, the speed, position, acceleration and even time differential calculus of the acceleration must be controlled severely. The system uses two-step control for the through-speed and the landing speed. Different systems that have been realized may include compensation for temperatures in flow rate control valves, load pressures, and oil viscosity, from learning control to fuzzy control for psychological effects, or control of inverters in motors. 13 refs., 12 figs., 1 tab.

Does formal mentoring for faculty members matter? A survey of clinical faculty members.

Science.gov (United States)

Mylona, Elza; Brubaker, Linda; Williams, Valerie N; Novielli, Karen D; Lyness, Jeffrey M; Pollart, Susan M; Dandar, Valerie; Bunton, Sarah A

2016-06-01

Mentoring relationships, for all medical school faculty members, are an important component of lifelong development and education, yet an understanding of mentoring among medical school clinical faculty members is incomplete. This study examined associations between formal mentoring relationships and aspects of faculty members' engagement and satisfaction. It then explored the variability of these associations across subgroups of clinical faculty members to understand the status of mentoring and outcomes of mentoring relationships. The authors hypothesised that academic clinical faculty members currently in formal mentoring relationships experience enhanced employee engagement and satisfaction with their department and institution. Medical school faculty members at 26 self-selected USA institutions participated in the 2011-2014 Faculty Forward Engagement Survey. Responses from clinical faculty members were analysed for relationships between mentoring status and perceptions of engagement by faculty members. Of the 11 953 clinical faculty respondents, almost one-third reported having a formal mentoring relationship (30%; 3529). Most mentored faculty indicated the relationship was important (86%; n = 3027), and over three-fourths were satisfied with their mentoring experience (77%; n = 2722). Mentored faculty members across ranks reported significantly higher levels of satisfaction and more positive perceptions of their roles in the organisation. Faculty members who were not receiving mentoring reported significantly less satisfaction with their workplace environment and lower overall satisfaction. Mentored clinical faculty members have significantly greater satisfaction with their department and institution. This multi-institutional study provides evidence that fostering mentoring opportunities may facilitate faculty members' satisfaction and engagement, which, in turn, may help medical schools retain high-quality faculty staff committed to the multidimensional

Effects of elevated atmospheric carbon dioxide on biomass and carbon accumulation in a model regenerating longleaf pine community.

Science.gov (United States)

Runion, G B; Davis, M A; Pritchard, S G; Prior, S A; Mitchell, R J; Torbert, H A; Rogers, H H; Dute, R R

2006-01-01

Plant species vary in response to atmospheric CO2 concentration due to differences in physiology, morphology, phenology, and symbiotic relationships. These differences make it very difficult to predict how plant communities will respond to elevated CO2. Such information is critical to furthering our understanding of community and ecosystem responses to global climate change. To determine how a simple plant community might respond to elevated CO2, a model regenerating longleaf pine community composed of five species was exposed to two CO2 regimes (ambient, 365 micromol mol(-1) and elevated, 720 micromol mol(-1)) for 3 yr. Total above- and belowground biomass was 70 and 49% greater, respectively, in CO2-enriched plots. Carbon (C) content followed a response pattern similar to biomass, resulting in a significant increase of 13.8 Mg C ha(-1) under elevated CO2. Responses of individual species, however, varied. Longleaf pine (Pinus palustris Mill.) was primarily responsible for the positive response to CO2 enrichment. Wiregrass (Aristida stricta Michx.), rattlebox (Crotalaria rotundifolia Walt. Ex Gmel.), and butterfly weed (Asclepias tuberosa L.) exhibited negative above- and belowground biomass responses to elevated CO2, while sand post oak (Quercus margaretta Ashe) did not differ significantly between CO2 treatments. As with pine, C content followed patterns similar to biomass. Elevated CO2 resulted in alterations in community structure. Longleaf pine comprised 88% of total biomass in CO2-enriched plots, but only 76% in ambient plots. In contrast, wiregrass, rattlebox, and butterfly weed comprised 19% in ambient CO2 plots, but only 8% under high CO2. Therefore, while longleaf pine may perform well in a high CO2 world, other members of this community may not compete as well, which could alter community function. Effects of elevated CO2 on plant communities are complex, dynamic, and difficult to predict, clearly demonstrating the need for more research in this

Approximation by Chebyshevian Bernstein Operators versus Convergence of Dimension Elevation

KAUST Repository

Ait-Haddou, Rachid; Mazure, Marie-Laurence

2016-01-01

On a closed bounded interval, consider a nested sequence of Extended Chebyshev spaces possessing Bernstein bases. This situation automatically generates an infinite dimension elevation algorithm transforming control polygons of any given level into control polygons of the next level. The convergence of these infinite sequences of polygons towards the corresponding curves is a classical issue in computer-aided geometric design. Moreover, according to recent work proving the existence of Bernstein-type operators in such Extended Chebyshev spaces, this nested sequence is automatically associated with an infinite sequence of Bernstein operators which all reproduce the same two-dimensional space. Whether or not this sequence of operators converges towards the identity on the space of all continuous functions is a natural issue in approximation theory. In the present article, we prove that the two issues are actually equivalent. Not only is this result interesting on the theoretical side, but it also has practical implications. For instance, it provides us with a Korovkin-type theorem of convergence of any infinite dimension elevation algorithm. It also enables us to tackle the question of convergence of the dimension elevation algorithm for any nested sequence obtained by repeated integration of the kernel of a given linear differential operator with constant coefficients. © 2016 Springer Science+Business Media New York

Approximation by Chebyshevian Bernstein Operators versus Convergence of Dimension Elevation

KAUST Repository

Ait-Haddou, Rachid

2016-03-18

On a closed bounded interval, consider a nested sequence of Extended Chebyshev spaces possessing Bernstein bases. This situation automatically generates an infinite dimension elevation algorithm transforming control polygons of any given level into control polygons of the next level. The convergence of these infinite sequences of polygons towards the corresponding curves is a classical issue in computer-aided geometric design. Moreover, according to recent work proving the existence of Bernstein-type operators in such Extended Chebyshev spaces, this nested sequence is automatically associated with an infinite sequence of Bernstein operators which all reproduce the same two-dimensional space. Whether or not this sequence of operators converges towards the identity on the space of all continuous functions is a natural issue in approximation theory. In the present article, we prove that the two issues are actually equivalent. Not only is this result interesting on the theoretical side, but it also has practical implications. For instance, it provides us with a Korovkin-type theorem of convergence of any infinite dimension elevation algorithm. It also enables us to tackle the question of convergence of the dimension elevation algorithm for any nested sequence obtained by repeated integration of the kernel of a given linear differential operator with constant coefficients. © 2016 Springer Science+Business Media New York

Strengthening of the Timber Members Using Fibre Reinforced Polymer Composites

Directory of Open Access Journals (Sweden)

Ioana-Sorina Enţuc

2004-01-01

Full Text Available The reinforcement of structural wood products has become in the last decades an efficient method of improving structural capabilities of load carrying members made of this material. Some important steps in earlier stages of research were focused on using metallic reinforcement, including steel bars, prestressed stranded cables, and bonded steel and aluminum plates. A disadvantage of the metallic reinforcement was the poor compatibility between the wood and the reinforcing materials. In comparison with metallic reinforcement, fiber reinforced polymers (FRP composites are compatible with structural wood products leading to efficient hybrid members. Some interesting strengthening alternatives using FRP applied to wood beams and to wood columns are presented in this paper.

The 3D Elevation Program initiative: a call for action

Science.gov (United States)

Sugarbaker, Larry J.; Constance, Eric W.; Heidemann, Hans Karl; Jason, Allyson L.; Lukas, Vicki; Saghy, David L.; Stoker, Jason M.

2014-01-01

The 3D Elevation Program (3DEP) initiative is accelerating the rate of three-dimensional (3D) elevation data collection in response to a call for action to address a wide range of urgent needs nationwide. It began in 2012 with the recommendation to collect (1) high-quality light detection and ranging (lidar) data for the conterminous United States (CONUS), Hawaii, and the U.S. territories and (2) interferometric synthetic aperture radar (ifsar) data for Alaska. Specifications were created for collecting 3D elevation data, and the data management and delivery systems are being modernized. The National Elevation Dataset (NED) will be completely refreshed with new elevation data products and services. The call for action requires broad support from a large partnership community committed to the achievement of national 3D elevation data coverage. The initiative is being led by the U.S. Geological Survey (USGS) and includes many partners—Federal agencies and State, Tribal, and local governments—who will work together to build on existing programs to complete the national collection of 3D elevation data in 8 years. Private sector firms, under contract to the Government, will continue to collect the data and provide essential technology solutions for the Government to manage and deliver these data and services. The 3DEP governance structure includes (1) an executive forum established in May 2013 to have oversight functions and (2) a multiagency coordinating committee based upon the committee structure already in place under the National Digital Elevation Program (NDEP). The 3DEP initiative is based on the results of the National Enhanced Elevation Assessment (NEEA) that was funded by NDEP agencies and completed in 2011. The study, led by the USGS, identified more than 600 requirements for enhanced (3D) elevation data to address mission-critical information requirements of 34 Federal agencies, all 50 States, and a sample of private sector companies and Tribal and local

Soil nematodes show a mid-elevation diversity maximum and elevational zonation on Mt. Norikura, Japan.

Science.gov (United States)

Dong, Ke; Moroenyane, Itumeleng; Tripathi, Binu; Kerfahi, Dorsaf; Takahashi, Koichi; Yamamoto, Naomichi; An, Choa; Cho, Hyunjun; Adams, Jonathan

2017-06-08

Little is known about how nematode ecology differs across elevational gradients. We investigated the soil nematode community along a ~2,200 m elevational range on Mt. Norikura, Japan, by sequencing the 18S rRNA gene. As with many other groups of organisms, nematode diversity showed a high correlation with elevation, and a maximum in mid-elevations. While elevation itself, in the context of the mid domain effect, could predict the observed unimodal pattern of soil nematode communities along the elevational gradient, mean annual temperature and soil total nitrogen concentration were the best predictors of diversity. We also found nematode community composition showed strong elevational zonation, indicating that a high degree of ecological specialization that may exist in nematodes in relation to elevation-related environmental gradients and certain nematode OTUs had ranges extending across all elevations, and these generalized OTUs made up a greater proportion of the community at high elevations - such that high elevation nematode OTUs had broader elevational ranges on average, providing an example consistent to Rapoport's elevational hypothesis. This study reveals the potential for using sequencing methods to investigate elevational gradients of small soil organisms, providing a method for rapid investigation of patterns without specialized knowledge in taxonomic identification.

Cavity resonance absorption in ultra-high bandwidth CRT deflection structure by a resistive load

Science.gov (United States)

Dunham, M.E.; Hudson, C.L.

1993-05-11

An improved ultra-high bandwidth helical coil deflection structure for a cathode ray tube is described comprising a first metal member having a bore therein, the metal walls of which form a first ground plane; a second metal member coaxially mounted in the bore of the first metal member and forming a second ground plane; a helical deflection coil coaxially mounted within the bore between the two ground planes; and a resistive load disposed in one end of the bore and electrically connected to the first and second ground planes, the resistive load having an impedance substantially equal to the characteristic impedance of the coaxial line formed by the two coaxial ground planes to inhibit cavity resonance in the structure within the ultra-high bandwidth of operation. Preferably, the resistive load comprises a carbon film on a surface of an end plug in one end of the bore.

High-resolution pattern of mangrove species distribution is controlled by surface elevation

Science.gov (United States)

Leong, Rick C.; Friess, Daniel A.; Crase, Beth; Lee, Wei Kit; Webb, Edward L.

2018-03-01

Mangrove vegetation species respond to multiple environmental gradients, and an enhanced understanding of how mangrove species are distributed across these gradients will facilitate conservation and management. Many environmental gradients correlate with tidal inundation; however small-scale inundation patterns resulting from microtopographical changes are difficult to capture empirically. In contrast, surface elevation is often a suitable, measurable and cost-effective proxy for inundation. This study investigated the relationships between species distribution and surface elevation in a mangrove forest in northwest Singapore. Through high-resolution land surveying, we developed a digital elevation model (DEM) and conducted a comprehensive survey of 4380 trees with a stem diameter ≥ 5 cm. A total of 15 species were encountered, and elevation envelopes were generated for 12. Species envelopes were distributed along an elevation continuum, with most species overlapping within the continuum. Spatial autocorrelation (SAC) was present for nine of the 15 species, and when taken into account, species ordering was modified across the elevation continuum. The presence of SAC strongly reinforces the need for research to control for SAC: classical spatial description of mangrove species distribution should be revised to account for ecological factors. This study suggests that (1) surface elevation applies strong controls on species distribution and (2) most mangroves at our study site have similar physiological tolerances.

Growth and Wood/Bark Properties of Abies faxoniana Seedlings as Affected by Elevated CO2

Institute of Scientific and Technical Information of China (English)

Yun-Zhou Qiao; Yuan-Bin Zhang; Kai-Yun Wang; Qian Wang; Qi-Zhuo Tian

2008-01-01

Growth and wood and bark properties of Abies faxoniana seedlings after one year's exposure to elevated CO2 concentration (ambient + 350 (=1= 25) μmol/mol) under two planting densities (28 or 84 plants/mz) were investigated in closed-top chambers. Tree height, stem diameter and cross-sectional area, and total biomass were enhanced under elevated CO2 concentration, and reduced under high planting density. Most traits of stem bark were improved under elevated CO2 concentration and reduced under high planting density. Stem wood production was significantly increased in volume under elevated CO2 concentration under both densities, and the stem wood density decreased under elevated CO2 concentration and increased under high planting density. These results suggest that the response of stem wood and bark to elevated CO2 concentration is density dependent. This may be of great importance in a future CO2 enriched world in natural forests where plant density varies considerably. The results also show that the bark/wood ratio in diameter, stem cross-sectional area and dry weight are not proportionally affected by elevated CO2 concentration under the two contrasting planting densities. This indicates that the response magnitude of stem bark and stem wood to elevated CO2 concentration are different but their response directions are the same.

3D-printing porosity: A new approach to creating elevated porosity materials and structures.

Science.gov (United States)

Jakus, A E; Geisendorfer, N R; Lewis, P L; Shah, R N

2018-05-01

We introduce a new process that enables the ability to 3D-print high porosity materials and structures by combining the newly introduced 3D-Painting process with traditional salt-leaching. The synthesis and resulting properties of three 3D-printable inks comprised of varying volume ratios (25:75, 50:50, 70:30) of CuSO 4 salt and polylactide-co-glycolide (PLGA), as well as their as-printed and salt-leached counterparts, are discussed. The resulting materials are comprised entirely of PLGA (F-PLGA), but exhibit porosities proportional to the original CuSO 4 content. The three distinct F-PLGA materials exhibit average porosities of 66.6-94.4%, elastic moduli of 112.6-2.7 MPa, and absorbency of 195.7-742.2%. Studies with adult human mesenchymal stem cells (hMSCs) demonstrated that elevated porosity substantially promotes cell adhesion, viability, and proliferation. F-PLGA can also act as carriers for weak, naturally or synthetically-derived hydrogels. Finally, we show that this process can be extended to other materials including graphene, metals, and ceramics. Porosity plays an essential role in the performance and function of biomaterials, tissue engineering, and clinical medicine. For the same material chemistry, the level of porosity can dictate if it is cell, tissue, or organ friendly; with low porosity materials being far less favorable than high porosity materials. Despite its importance, it has been difficult to create three-dimensionally printed structures that are comprised of materials that have extremely high levels of internal porosity yet are surgically friendly (able to handle and utilize during surgical operations). In this work, we extend a new materials-centric approach to 3D-printing, 3D-Painting, to 3D-printing structures made almost entirely out of water-soluble salt. The structures are then washed in a specific way that not only extracts the salt but causes the structures to increase in size. With the salt removed, the resulting medical polymer

The members of the Agency

International Nuclear Information System (INIS)

1996-01-01

The document lists the 124 Member States of the Agency as of 1 September 1996. The new Member since the last issue of the list (INFCIRC/2/Rev.47) is Georgia. In an attachment are given the dates on which the 124 Member States became Members, the State (Latvia) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the State (Republic of Moldova) whose application for membership has been recommended by the Board of Governors for approval by the General Conference

The members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-10

The document lists the 124 Member States of the Agency as of 1 September 1996. The new Member since the last issue of the list (INFCIRC/2/Rev.47) is Georgia. In an attachment are given the dates on which the 124 Member States became Members, the State (Latvia) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the State (Republic of Moldova) whose application for membership has been recommended by the Board of Governors for approval by the General Conference.

EFFECT OF ELEVATED TEMPERATURE ON COMPRESSIVE STRENGTH OF FIBER REINFORCED CONCRETE

OpenAIRE

Prashant shinkar*, Prof. Deepak kakade, Dr.A.P.Wadekar

2017-01-01

This paper deals with the mechanical properties of concrete with steel fibers subjected to temperatures up to 500°C. Now a day concrete are being used extensively in the construction that might be subjected to elevated temperatures. The behavior of concrete structures at elevated temperatures is of significant importance in predicting the safety of structures in response to certain accidents or particular service conditions. Concrete mixes of M 50 have been designed along with steel fibers fr...

Cerebral Pulsatility Index Is Elevated in Patients with Elevated Right Atrial Pressure.

Science.gov (United States)

Lahiri, Shouri; Schlick, Konrad H; Padrick, Matthew M; Rinsky, Brenda; Gonzalez, Nestor; Jones, Heather; Mayer, Stephan A; Lyden, Patrick D

2018-01-01

Extracerebral venous congestion can precipitate intracranial hypertension due to obstruction of cerebral blood outflow. Conditions that increase right atrial pressure, such as hypervolemia, are thought to increase resistance to jugular venous outflow and contribute to cerebro-venous congestion. Cerebral pulsatility index (CPI) is considered a surrogate marker of distal cerebrovascular resistance and is elevated with intracranial hypertension. Thus, we sought to test the hypothesis that elevated right atrial pressure is associated with increased CPI compared to normal right atrial pressure. We retrospectively reviewed 61 consecutive patients with subarachnoid hemorrhage. We calculated CPI from transcranial Doppler studies and correlated these with echocardiographic measures of right atrial pressure. CPIs were compared from patients with elevated and normal right atrial pressure. There was a significant difference between CPI obtained from all patients with elevated right atrial pressure compared to those with normal right atrial pressure (P right and left hemispheric CPI from patients with both elevated and normal right atrial pressure. Patients with elevated right atrial pressure had significantly higher CPI compared to patients with normal right atrial pressure. These findings suggest that cerebro-venous congestion due to impaired jugular venous outflow may increase distal cerebrovascular resistance as measured by CPI. Since elevated CPI is associated with poor outcome in numerous neurological conditions, future studies are needed to elucidate the significance of these results in other populations. Copyright © 2017 by the American Society of Neuroimaging.

Experimental prototype of an electric elevator

Science.gov (United States)

Gaiceanu, M.; Epure, S.; Ciuta, S.

2016-08-01

The main objective is to achieve an elevator prototype powered by a three-phase voltage system via a bidirectional static power converter ac-ac with regenerating capability. In order to diminish the power size of the electric motor up to 1/3 of rated power, the elevator contains two carriages of the same weight, one serving as the payload, and the other as counterweight. Before proper operation of the static power converter, the capacitor must be charged at rated voltage via a precharge circuit. At the moment of stabilizing the DC voltage at nominal value, the AC-AC power converter can operates in the proper limits. The functions of the control structure are: the load control task, speed and torque controls. System includes transducers for current measuring, voltage sensors and encoder. As reserve power sources the hybrid battery-photovoltaic panels are used. The control voltage is modulated by implementing four types of pulse width modulations: sinusoidal, with reduced commutation, third order harmonic insertion, and the space vector modulation. Therefore, the prototype could operates with an increased efficiency, in spite of the existing ones. The experimental results confirm the well design of the chosen solution. The control solution assures bidirectional power flow control, precharge control, and load control and it is implemented on a digital signal processor. The elevator capacity is between 300-450 kg, and it is driven by using a 1.5 kW three-phase asynchronous machine.

Modeling and characterization of strengthened concrete tension members

DEFF Research Database (Denmark)

Hansen, Christian Skodborg; Stang, Henrik

2011-01-01

The structural potential for cracking of externally strengthened concrete tension members, can be predicted with three parameters, describing the structural cracking potential based on fracture mechanical properties of the of concrete and interface between concrete and strengthening medium....... With these parameters, it is possible to design reinforcement and obtain a required cracking behavior of a given structure. Design recommendations for single and multiple cracking of the tension specimen are given in terms of fracture mechanical parameters, and a structural stiffness parameter....

THE FISCAL PRESSURE IN THE EU MEMBER STATES

Directory of Open Access Journals (Sweden)

DOBROTĂ GABRIELA

2011-03-01

Full Text Available The development of an economy is determined in a significant proportion by the tax system structure, by how it exercises its functions and ensures the collection of state resources. A high tax efficiency, due to the acceptability of tax provisions are the ideal conditions of any tax system. In this context, it is obvious that most tax systems have undergone significant changes under the impact of the action of a complex system of factors. Increased need for resources in various countries was reflected in attempts to identify the relationship that allows both the securing of the necessary funds and their economic and social development. The quantification of the fiscal pressure on the EU member states show a wide range of tax rates. This paper makes a comparative analysis of the degree of taxation in the EU member states.

The Coupling of Treeline Elevation and Temperature is Mediated by Non-Thermal Factors on the Tibetan Plateau

Directory of Open Access Journals (Sweden)

Yafeng Wang

2017-04-01

Full Text Available Little is known about the relationships between treeline elevation and climate at regional and local scales. It is compelling to fill this research gap with data from the Tibetan Plateau where some of the highest alpine treelines in the world are found. This research question partially results from the lack of in situ temperature data at treeline sites. Herein, treeline variables (e.g., elevation, topography, tree species and temperature data were collected from published investigations performed during this decade on the Tibetan Plateau. Temperature conditions near treeline sites were estimated using global databases and these estimates were corrected by using in situ air temperature measurements. Correlation analyses and generalized linear models were used to evaluate the effects of different variables on treeline elevation including thermal (growing-season air temperatures and non-thermal (latitude, longitude, elevation, tree species, precipitation, radiation factors. The commonality analysis model was applied to explore how several variables (July mean temperature, elevation of mountain peak, latitude were related to treeline elevation. July mean temperature was the most significant predictor of treeline elevation, explaining 55% of the variance in treeline elevation across the Tibetan Plateau, whereas latitude, tree species, and mountain elevation (mass-elevation effect explained 30% of the variance in treeline elevation. After considering the multicollinearity among predictors, July mean temperature (largely due to the influence of minimum temperature still showed the strongest association with treeline elevation. We conclude that the coupling of treeline elevation and July temperature at a regional scale is modulated by non-thermal factors probably acting at local scales. Our results contribute towards explaining the decoupling between climate warming and treeline dynamics.

An elevator

Energy Technology Data Exchange (ETDEWEB)

Loginovskiy, V.I.; Medinger, N.V.; Rasskazov, V.A.; Solonitsyn, V.A.

1983-01-01

An elevator is proposed which includes a body, spring loaded cams and a shut-off ring. To increase the reliability of the elevator by eliminating the possibility of spontaneous shifting of the shut-off ring, the latter is equipped with handles hinged to it and is made with evolvent grooves. The cams are equipped with rollers installed in the evolvent grooves of the shut off ring, where the body is made with grooves for the handles.

The Switching Decision: Are Members of Superannuation Funds Rational and Informed Investors?

Directory of Open Access Journals (Sweden)

Sarath Delpachitra

2014-10-01

Full Text Available The recent Cooper Review (Cooper 2010 attempted to address governance, structure, efficiency and operational problems by recommending changes without pinpointing the root causes and systematic design flaws of the Australian Superannuation System. Despite overwhelming evidence that members’ disengagement was a root cause of the problems, little attention was paid to the motivation and background of members to facilitate participation and decision-making. For instance, a very small percentage of members take their role in the superannuation industry seriously. This is evidenced by the fact that a very small percentage of members (2.5% in 2007 actively changed superannuation fund and most new fund members ‘defaulted’ into employer-selected funds (Bateman 2009. This may be that they are serious but lack the ability or time to monitor investments in a way required by a sophisticated system. This paper explores the drivers of switching superannuation funds of those working-age Australians. It also analyses the presentation of fund information to the sample population to examine how members use information in their superannuation decisions. This may add insight to the ways fund information is made available and also to the types of members who may need more protection, support or education.

Factors Associated With Elevated Blood Lead Levels in Children.

Science.gov (United States)

Chaudhary, Sakshi; Firdaus, Uzma; Ali, Syed Manazir; Mahdi, Abbas Ali

2018-01-15

To determine the prevalence and correlates of elevated blood lead level in children (6-144 months) of Aligarh. A hospital-based cross-sectional study was conducted. Venous blood was obtained for lead estimation and a structured questionnaire was filled. A total of 260 children were enrolled. The prevalence of elevated blood lead level was 44.2%, seen mostly in children below 5 years of age. Old and deteriorating wall paints at home was found to be significantly associated with elevated levels. Lead-based house paints are potential source of lead exposure. Meticulous renovation and painting of the walls with safe paints is desirable.

Model Agreements for the granting of Associate Member Status Implementation arrangements concerning eligibility for personnel appointments and industrial participation for Associate Member States Progress report by the Management

CERN Document Server

2011-01-01

Model Agreements for the granting of Associate Member Status Implementation arrangements concerning eligibility for personnel appointments and industrial participation for Associate Member States Progress report by the Management

VizieR Online Data Catalog: NGC 6802 dwarf cluster members and non-members (Tang+, 2017)

Science.gov (United States)

Tang, B.; Geisler, D.; Friel, E.; Villanova, S.; Smiljanic, R.; Casey, A. R.; Randich, S.; Magrini, L.; San, Roman I.; Munoz, C.; Cohen, R. E.; Mauro, F.; Bragaglia, A.; Donati, P.; Tautvaisiene, G.; Drazdauskas, A.; Zenoviene, R.; Snaith, O.; Sousa, S.; Adibekyan, V.; Costado, M. T.; Blanco-Cuaresma, S.; Jimenez-Esteban, F.; Carraro, G.; Zwitter, T.; Francois, P.; Jofre, P.; Sordo, R.; Gilmore, G.; Flaccomio, E.; Koposov, S.; Korn, A. J.; Lanzafame, A. C.; Pancino, E.; Bayo, A.; Damiani, F.; Franciosini, E.; Hourihane, A.; Lardo, C.; Lewis, J.; Monaco, L.; Morbidelli, L.; Prisinzano, L.; Sacco, G.; Worley, C. C.; Zaggia, S.

2016-11-01

The dwarf stars in NGC 6802 observed by GIRAFFE spectrograph are separated into four tables: 1. cluster members in the lower main sequence; 2. cluster members in the upper main sequence; 3. non-member dwarfs in the lower main sequence; 4. non-member dwarfs in the upper main sequence. The star coordinates, V band magnitude, V-I color, and radial velocity are given. (4 data files).

Data Elevator

Energy Technology Data Exchange (ETDEWEB)

2017-04-29

Data Elevator: Efficient Asynchronous Data Movement in Hierarchical Storage Systems Multi-layer storage subsystems, including SSD-based burst buffers and disk-based parallel file systems (PFS), are becoming part of HPC systems. However, software for this storage hierarchy is still in its infancy. Applications may have to explicitly move data among the storage layers. We propose Data Elevator for transparently and efficiently moving data between a burst buffer and a PFS. Users specify the final destination for their data, typically on PFS, Data Elevator intercepts the I/O calls, stages data on burst buffer, and then asynchronously transfers the data to their final destination in the background. This system allows extensive optimizations, such as overlapping read and write operations, choosing I/O modes, and aligning buffer boundaries. In tests with large-scale scientific applications, Data Elevator is as much as 4.2X faster than Cray DataWarp, the start-of-art software for burst buffer, and 4X faster than directly writing to PFS. The Data Elevator library uses HDF5's Virtual Object Layer (VOL) for intercepting parallel I/O calls that write data to PFS. The intercepted calls are redirected to the Data Elevator, which provides a handle to write the file in a faster and intermediate burst buffer system. Once the application finishes writing the data to the burst buffer, the Data Elevator job uses HDF5 to move the data to final destination in an asynchronous manner. Hence, using the Data Elevator library is currently useful for applications that call HDF5 for writing data files. Also, the Data Elevator depends on the HDF5 VOL functionality.

Member Checking: A Tool to Enhance Trustworthiness or Merely a Nod to Validation?

Science.gov (United States)

Birt, Linda; Scott, Suzanne; Cavers, Debbie; Campbell, Christine; Walter, Fiona

2016-06-22

The trustworthiness of results is the bedrock of high quality qualitative research. Member checking, also known as participant or respondent validation, is a technique for exploring the credibility of results. Data or results are returned to participants to check for accuracy and resonance with their experiences. Member checking is often mentioned as one in a list of validation techniques. This simplistic reporting might not acknowledge the value of using the method, nor its juxtaposition with the interpretative stance of qualitative research. In this commentary, we critique how member checking has been used in published research, before describing and evaluating an innovative in-depth member checking technique, Synthesized Member Checking. The method was used in a study with patients diagnosed with melanoma. Synthesized Member Checking addresses the co-constructed nature of knowledge by providing participants with the opportunity to engage with, and add to, interview and interpreted data, several months after their semi-structured interview. © The Author(s) 2016.

Photographic Standards for Patients With Facial Palsy and Recommendations by Members of the Sir Charles Bell Society.

Science.gov (United States)

Santosa, Katherine B; Fattah, Adel; Gavilán, Javier; Hadlock, Tessa A; Snyder-Warwick, Alison K

2017-07-01

There is no widely accepted assessment tool or common language used by clinicians caring for patients with facial palsy, making exchange of information challenging. Standardized photography may represent such a language and is imperative for precise exchange of information and comparison of outcomes in this special patient population. To review the literature to evaluate the use of facial photography in the management of patients with facial palsy and to examine the use of photography in documenting facial nerve function among members of the Sir Charles Bell Society-a group of medical professionals dedicated to care of patients with facial palsy. A literature search was performed to review photographic standards in patients with facial palsy. In addition, a cross-sectional survey of members of the Sir Charles Bell Society was conducted to examine use of medical photography in documenting facial nerve function. The literature search and analysis was performed in August and September 2015, and the survey was conducted in August and September 2013. The literature review searched EMBASE, CINAHL, and MEDLINE databases from inception of each database through September 2015. Additional studies were identified by scanning references from relevant studies. Only English-language articles were eligible for inclusion. Articles that discussed patients with facial palsy and outlined photographic guidelines for this patient population were included in the study. The survey was disseminated to the Sir Charles Bell Society members in electronic form. It consisted of 10 questions related to facial grading scales, patient-reported outcome measures, other psychological assessment tools, and photographic and videographic recordings. In total, 393 articles were identified in the literature search, 7 of which fit the inclusion criteria. Six of the 7 articles discussed or proposed views specific to patients with facial palsy. However, none of the articles specifically focused on

Complex Determinants in Specific Members of the Mannose Receptor Family Govern Collagen Endocytosis

DEFF Research Database (Denmark)

Jürgensen, Henrik J; Johansson, Kristina; Madsen, Daniel H

2014-01-01

Members of the well-conserved mannose receptor (MR) protein family have been functionally implicated in diverse biological and pathological processes. Importantly, a proposed common function is the internalization of collagen for intracellular degradation occurring during bone development, cancer...... invasion, and fibrosis protection. This functional relationship is suggested by a common endocytic capability and a candidate collagen-binding domain. Here we conducted a comparative investigation of each member's ability to facilitate intracellular collagen degradation. As expected, the family members u......PARAP/Endo180 and MR bound collagens in a purified system and internalized collagens for degradation in cellular settings. In contrast, the remaining family members, PLA2R and DEC-205, showed no collagen binding activity and were unable to mediate collagen internalization. To pinpoint the structural elements...

17 CFR 240.19c-3 - Governing off-board trading by members of national securities exchanges.

Science.gov (United States)

2010-04-01

... members of national securities exchanges. 240.19c-3 Section 240.19c-3 Commodity and Securities Exchanges... Members § 240.19c-3 Governing off-board trading by members of national securities exchanges. The rules of each national securities exchange shall provide as follows: (a) No rule, stated policy or practice of...

Mineralization of linear alkylbenzene sulfonate by a four-member aerobic bacterial consortium

International Nuclear Information System (INIS)

Jimenez, L.; Breen, A.; Thomas, N.; Sayler, G.S.; Federle, T.W.

1991-01-01

A bacterial consortium capable of linear alkylbenzene sulfonate (LAS) mineralization under aerobic conditions was isolated from a chemostat inoculated with activated sludge. The consortium, designated KJB, consisted of four members, all of which were gram-negative, rod-shaped bacteria that grew in pairs and short chains. Three isolates had biochemical properties characteristic of Pseudomonas spp.; the fourth showed characteristics of the Aeromonas spp. Cell suspensions were grown together in minimal medium with [ 14 C]LAS as the only carbon source. After 13 days of incubation, more than 25% of the [ 14 C]LAS was mineralized to 14 CO 2 by the consortium. Pure bacterial cultures and combinations lacking any one member of the KJB bacterial consortium did not mineralize LAS. Three isolates carried out primary biodegradation of the surfactant, and one did not. This study shows that the four bacteria complemented each other and synergistically mineralized LAS, indicating catabolic cooperation among the four consortium members

Chipmunk parvovirus is distinct from members in the genus Erythrovirus of the family Parvoviridae.

Directory of Open Access Journals (Sweden)

Zhaojun Chen

2010-12-01

Full Text Available The transcription profile of chipmunk parvovirus (ChpPV, a tentative member of the genus Erythrovirus in the subfamily Parvovirinae of the family Parvoviridae, was characterized by transfecting a nearly full-length genome. We found that it is unique from the profiles of human parvovirus B19 and simian parvovirus, the members in the genus Erythrovirus so far characterized, in that the small RNA transcripts were not processed for encoding small non-structural proteins. However, like the large non-structural protein NS1 of the human parvovirus B19, the ChpPV NS1 is a potent inducer of apoptosis. Further phylogenetic analysis of ChpPV with other parvoviruses in the subfamily Parvovirinae indicates that ChpPV is distinct from the members in genus Erythrovirus. Thus, we conclude that ChpPV may represent a new genus in the family Parvoviridae.

Seismic analysis for the supporting member of the Westinghouse AP1000 steam generator

International Nuclear Information System (INIS)

Xu Yu; Huang Mei; Tian Li; Hou Zhousen

2012-01-01

In this paper, the seismic performance analysis for the Supporting member of is carried out under the combined loads, including dead weight, earthquake loads, by using response spectrum analysis method in ANSYS. The stress qualification is also carried out based on ASME-Ⅲ-NF code. The results show that the stress of the Supporting member meets the seismic requirements for equipment, and the deformation of structure is within the allowable limits. (authors)

The Members of the Agency

International Nuclear Information System (INIS)

1999-01-01

The document lists the 130 Member States of the Agency as of 1 December 1999. The new Member since the last issue of the list (INFCIRC/2/52) is Angola. The dates on which the present 130 Member States became Members, and the state Honduras) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute are given in an Attachment

Nitrogen Deifciency Limited the Improvement of Photosynthesis in Maize by Elevated CO2 Under Drought

Institute of Scientific and Technical Information of China (English)

ZONG Yu-zheng; SHANGGUAN Zhou-ping

2014-01-01

Global environmental change affects plant physiological and ecosystem processes. The interaction of elevated CO2, drought and nitrogen (N) deficiency result in complex responses of C4 species photosynthetic process that challenge our current understanding. An experiment of maize (Zea mays L.) involving CO2 concentrations (380 or 750 µmol mol-1, climate chamber), osmotic stresses (10% PEG-6000, -0.32 MPa) and nitrogen constraints (N deficiency treated since the 144th drought hour) was carried out to investigate its photosynthesis capacity and leaf nitrogen use efficiency. Elevated CO2 could alleviate drought-induced photosynthetic limitation through increasing capacity of PEPC carboxylation (Vpmax) and decreasing stomatal limitations (SL). The N deifciency exacerbated drought-induced photosynthesis limitations in ambient CO2. Elevated CO2 partially alleviated the limitation induced by drought and N deifciency through improving the capacity of Rubisco carboxylation (Vmax) and decreasing SL. Plants with N deifciency transported more N to their leaves at elevated CO2, leading to a high photosynthetic nitrogen-use efifciency but low whole-plant nitrogen-use efifciency. The stress mitigation by elevated CO2 under N deifciency conditions was not enough to improving plant N use efifciency and biomass accumulation. The study demonstrated that elevated CO2 could alleviate drought-induced photosynthesis limitation, but the alleviation varied with N supplies.

Flaking and wave-like structure on metallic glasses induced by MeV-energy helium ions

International Nuclear Information System (INIS)

Paszti, F.; Fried, M.; Pogany, L.; Manuaba, A.; Mezey, G.; Kotai, E.; Lovas, I.; Lohner, T.; Pocs, L.

1982-11-01

Ten samples prepared from different kinds of metallic glasses (different in composition and manufacturing technology) were bombarded by 2 or 1 MeV helium ions with high fluence under different experimental circumstances. During bombardment the temperature increase of the samples caused by irradiation heating was estimated and kept below the temperature needed for the investigated metallic glass to be crystallized. In all cases the surface deformation processes were dominated by flaking i.e. nearly from the whole implanted area a layer suddenly flaked off with a uniform thickness of the applied ion projected range. The surface left behind the flaked layer can be characterized by a wave-like structure i.e. by a regular series of asymmetrical elevations. These elevations, which did not appear on the annealed samples, are caused by a mechanism developed during the bombardment of the amorphous structure (of metallic glasses) by high energy helium ions. Details of this unusual phenomenon are discussed. (author)

Personal technology use by U.S. military service members and veterans: an update.

Science.gov (United States)

Bush, Nigel E; Wheeler, William M

2015-04-01

Although personal electronic devices, such as mobile phones, computers, and tablets, increasingly are being leveraged as vehicles for health in the civilian world, almost nothing is known about personal technology use in the U.S. military. In 2012 we conducted a unique survey of personal technologies used by U.S. military service members. However, with the rapidly growing sophistication of personal technology and changes in consumer habits, that knowledge must be continuously updated to be useful. Accordingly, we recently surveyed new samples of active duty service members, National Guard and Reserve, and veterans. We collected data by online surveys in 2013 from 239 active, inactive, and former service members. Online surveys were completed in-person via laptop computers at a large military installation and remotely via Web-based surveys posted on the Army Knowledge Online Web site and on a Defense Center Facebook social media channel. We measured high rates of personal technology use by service members at home across popular electronic media. The most dramatic change since our earlier survey was the tremendous increase in mobile phone use at home for a wide variety of purposes. Participants also reported moderate non-work uses of computers and tablets while on recent deployment to Iraq and Afghanistan, but almost no mobile phone use, ostensibly because of military restrictions in the war zone. These latest results will enable researchers and technology developers target their efforts on the most promising and popular technologies for psychological health in the military.

The Members of the Agency

International Nuclear Information System (INIS)

2003-01-01

The document lists the 135 Member States of the Agency as of 19 March 2003. The new Member since the last issue of the list (INFCIRC/2/56) is the Republic of Honduras. The dates on which the present 135 Member States became Members are given in an Attachment. It also shows the States whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute

The Members of the Agency

International Nuclear Information System (INIS)

2002-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.55) is the Republic of Botswana, which deposited the instrument of acceptance of the Statute on 20 March 2002. The Attachment hereto shows the dates on which the present 134 Member States became Members. It also shows the State whose application for membership of the Agency has been approved by the General Conference, but which has not yet deposited an instrument of acceptance of the Statute

The Members of the Agency

International Nuclear Information System (INIS)

2001-01-01

The document lists the 132 Member States of the Agency as of 1 June 2001. The new Members since the last issue of the list (INFCIRC/2/53) are Central African Republic and Azerbaijan. The dates on which the present 132 Member States became Members are given in an Attachment. It also shows the States whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute

Perceptions and use of iPad technology by pharmacy practice faculty members.

Science.gov (United States)

DiVall, Margarita V; Zgarrick, David P

2014-04-17

To explore the potential of tablet technology to address the specific workload challenges of pharmacy practice faculty members and to evaluate tablet usage after a department-wide iPad initiative. After conducting a needs assessment to determine pharmacy faculty attitudes towards tablet technology and to identify potential usage scenarios, all faculty members in a department of pharmacy practice received an iPad. After iPad distribution, training sessions and virtual tutorials were provided. An anonymous survey was administered to evaluate the pilot. The needs assessment survey revealed positive attitudes towards iPad technology, identified use scenarios, and led to a department-wide iPad pilot program. Most faculty members used iPads for connectivity with students (86%), paper/project annotation (68%), assessment (57%), and demonstration of tools used in practice (36%). For teaching, 61% of faculty members used iPads in seminars/laboratories, 57% used iPads in the experiential setting, and 43% used iPads in the classroom. Use of iPads for patient-care activities varied and depended on site support for mobile technology. The 23 faculty members with external practice sites used iPads to a greater extent and had more positive attitudes towards this technology compared with campus-based faculty members. Integration of tablet technology into the pharmacy education setting resulted in faculty-reported increased productivity and decreased paper waste. It also allowed faculty members to experiment with new teaching strategies in the classroom and experiential setting. Administrators at institutions exploring the use of tablet technology should allocate resources based on faculty needs and usage patterns.

The sweet side of global change-dynamic responses of non-structural carbohydrates to drought, elevated CO2 and nitrogen fertilization in tree species.

Science.gov (United States)

Li, Weibin; Hartmann, Henrik; Adams, Henry D; Zhang, Hongxia; Jin, Changjie; Zhao, Chuanyan; Guan, Dexin; Wang, Anzhi; Yuan, Fenghui; Wu, Jiabing

2018-06-11

Non-structural carbohydrates (NSC) play a central role in plant functioning as energy carriers and building blocks for primary and secondary metabolism. Many studies have investigated how environmental and anthropogenic changes, like increasingly frequent and severe drought episodes, elevated CO2 and atmospheric nitrogen (N) deposition, influence NSC concentrations in individual trees. However, this wealth of data has not been analyzed yet to identify general trends using a common statistical framework. A thorough understanding of tree responses to global change is required for making realistic predictions of vegetation dynamics. Here we compiled data from 57 experimental studies on 71 tree species and conducted a meta-analysis to evaluate general responses of stored soluble sugars, starch and total NSC (soluble sugars + starch) concentrations in different tree organs (foliage, above-ground wood and roots) to drought, elevated CO2 and N deposition. We found that drought significantly decreased total NSC in roots (-17.3%), but not in foliage and above-ground woody tissues (bole, branch, stem and/or twig). Elevated CO2 significantly increased total NSC in foliage (+26.2%) and roots (+12.8%), but not in above-ground wood. By contrast, total NSC significantly decreased in roots (-17.9%), increased in above-ground wood (+6.1%), but was unaffected in foliage from N fertilization. In addition, the response of NSC to three global change drivers was strongly affected by tree taxonomic type, leaf habit, tree age and treatment intensity. Our results pave the way for a better understanding of general tree function responses to drought, elevated CO2 and N fertilization. The existing data also reveal that more long-term studies on mature trees that allow testing interactions between these factors are urgently needed to provide a basis for forecasting tree responses to environmental change at the global scale.

Elevated atmospheric CO2 increases microbial growth rates and enzymes activity in soil

Science.gov (United States)

Blagodatskaya, Evgenia; Blagodatsky, Sergey; Dorodnikov, Maxim; Kuzyakov, Yakov

2010-05-01

Increasing the belowground translocation of assimilated carbon by plants grown under elevated CO2 can cause a shift in the structure and activity of the microbial community responsible for the turnover of organic matter in soil. We investigated the long-term effect of elevated CO2 in the atmosphere on microbial biomass and specific growth rates in root-free and rhizosphere soil. The experiments were conducted under two free air carbon dioxide enrichment (FACE) systems: in Hohenheim and Braunschweig, as well as in the intensively managed forest mesocosm of the Biosphere 2 Laboratory (B2L) in Oracle, AZ. Specific microbial growth rates (μ) were determined using the substrate-induced respiration response after glucose and/or yeast extract addition to the soil. We evaluated the effect of elevated CO2 on b-glucosidase, chitinase, phosphatase, and sulfatase to estimate the potential enzyme activity after soil amendment with glucose and nutrients. For B2L and both FACE systems, up to 58% higher μ were observed under elevated vs. ambient CO2, depending on site, plant species and N fertilization. The μ-values increased linearly with atmospheric CO2 concentration at all three sites. The effect of elevated CO2 on rhizosphere microorganisms was plant dependent and increased for: Brassica napus=Triticum aestivumyeast extract then for those growing on glucose, i.e. the effect of elevated CO2 was smoothed on rich vs. simple substrate. So, the r/K strategies ratio can be better revealed by studying growth on simple (glucose) than on rich substrate mixtures (yeast extract). After adding glucose, enzyme activities under elevated CO2 were 1.2-1.9-fold higher than under ambient CO2. This indicates the increased activity of microorganisms, which leads to accelerated C turnover in soil under elevated CO2. Our results clearly showed that the functional characteristics of the soil microbial community (i.e. specific growth rates and enzymes activity) rather than total microbial biomass

Differentiating ST elevation myocardial infarction and nonischemic causes of ST elevation by analyzing the presenting electrocardiogram

DEFF Research Database (Denmark)

Jayroe, Jason B; Spodick, David H; Nikus, Kjell

2008-01-01

Guidelines recommend that patients with suggestive symptoms of myocardial ischemia and ST-segment elevation (STE) in > or =2 adjacent electrocardiographic leads should receive immediate reperfusion therapy. Novel strategies aimed to reduce door-to-balloon time, such as prehospital wireless...

Apparatus and method for determining stress and strain in pipes, pressure vessels, structural members and other deformable bodies

International Nuclear Information System (INIS)

Vachon, R.I.; Ranson, W.F.

1987-01-01

A method and apparatus for measuring stress and strain associated with a pipe, pressurized vessel, structural member or deformable body containing a flaw or stress concentration utilizes a laser beam to illuminate a surface being analyzed and an optical data digitizer to sense a signal provided by a speckle pattern produced by the light beam reflected from the illuminated surface. One signal is received from the surface in a reference condition and subsequent signals are received from the surface after surface deformation. The optical data digitizer provides the received signal to an image processor, and the processor stores the signals and correlates the deformed image received with the reference image and then sends this correlated information to a minicomputer which performs mathematical analyses of the signal to determine stress and strain associated with the surface. The apparatus is constructed as one integral unit, and further includes a digital and tape display, as well as a television monitor and an electro-optic range indicator. (author) 15 figs

Changes in the microbial community structure of bacteria, archaea and fungi in response to elevated CO(2) and warming in an Australian native grassland soil.

Science.gov (United States)

Hayden, Helen L; Mele, Pauline M; Bougoure, Damian S; Allan, Claire Y; Norng, Sorn; Piceno, Yvette M; Brodie, Eoin L; Desantis, Todd Z; Andersen, Gary L; Williams, Amity L; Hovenden, Mark J

2012-12-01

The microbial community structure of bacteria, archaea and fungi is described in an Australian native grassland soil after more than 5 years exposure to different atmospheric CO2 concentrations ([CO2]) (ambient, +550 ppm) and temperatures (ambient, + 2°C) under different plant functional types (C3 and C4 grasses) and at two soil depths (0-5 cm and 5-10 cm). Archaeal community diversity was influenced by elevated [CO2], while under warming archaeal 16S rRNA gene copy numbers increased for C4 plant Themeda triandra and decreased for the C3 plant community (P fungi in soil responded differently to elevated [CO2], warming and their interaction. Taxa identified as significantly climate-responsive could show differing trends in the direction of response ('+' or '-') under elevated CO2 or warming, which could then not be used to predict their interactive effects supporting the need to investigate interactive effects for climate change. The approach of focusing on specific taxonomic groups provides greater potential for understanding complex microbial community changes in ecosystems under climate change. © 2012 Society for Applied Microbiology and Blackwell Publishing Ltd.

The experiences of family members in the nursing home to hospital transfer decision

Directory of Open Access Journals (Sweden)

Kathleen Abrahamson

2016-11-01

Full Text Available Abstract Background The objective of this study was to better understand the experiences of family members in the nursing home to hospital transfer decision making process. Semi-structured interviews were conducted with 20 family members who had recently been involved in a nursing home to hospital transfer decision. Results Family members perceived themselves to play an advocacy role in their resident’s care and interview themes clustered within three over-arching categories: Family perception of the nursing home’s capacity to provide medical care: Resident and family choices; and issues at ‘hand-off’ and the hospital. Multiple sub-themes were also identified. Conclusions Findings from this study contribute to knowledge surrounding the nursing home transfer decision by illuminating the experiences of family members in the transfer decision process.

Geographic isolation and elevational gradients promote diversification in an endemic shrew on Sulawesi.

Science.gov (United States)

Eldridge, Ryan A; Achmadi, Anang S; Giarla, Thomas C; Rowe, Kevin C; Esselstyn, Jacob A

2018-01-01

Phylogeographic research on endemic primates and amphibians inhabiting the Indonesian island of Sulawesi revealed the existence of seven areas of endemism (AoEs). Here, we use phylogenetic and population genetic analyses of one mitochondrial gene and 15 nuclear loci to assess geographic patterns of genetic partitioning in a shrew (Crocidura elongata) that is endemic to Sulawesi, but occurs across the island. We uncover substantial genetic diversity in this species both between and within AoEs, but we also identify close relationships between populations residing in different AoEs. One of the earliest divergences within C. elongata distinguishes a high-elevation clade from low-elevation clades. In addition, on one mountain, we observe three distinct genetic groups from low, middle, and high elevations, suggesting divergence along a single elevational gradient. In general, our results show that C. elongata, like several other Sulawesi endemic taxa, harbors extensive genetic diversity. This diversity is structured in part by known AoE boundaries, but also by elevational gradients and geographic isolation within AoEs. Copyright © 2017 Elsevier Inc. All rights reserved.

Netball team members, but not hobby group members, distinguish team characteristics from group characteristics.

Science.gov (United States)

Stillman, Jennifer A; Fletcher, Richard B; Carr, Stuart C

2007-04-01

Research on groups is often applied to sport teams, and research on teams is often applied to groups. This study investigates the extent to which individuals have distinct schemas for groups and teams. A list of team and group characteristics was generated from 250 individuals, for use in this and related research. Questions about teams versus groups carry an a priori implication that differences exist; therefore, list items were presented to new participants and were analyzed using signal detection theory, which can accommodate a finding of no detectable difference between a nominated category and similar items. Participants were 30 members from each of the following: netball teams, the general public, and hobby groups. Analysis revealed few features that set groups apart from teams; however, teams were perceived as more structured and demanding, requiring commitment and effort toward shared goals. Team and group characteristics were more clearly defined to team members than they were to other participant groups. The research has implications for coaches and practitioners.

Distinct soil bacterial communities along a small-scale elevational gradient in alpine tundra

Directory of Open Access Journals (Sweden)

Congcong eShen

2015-06-01

Full Text Available The elevational diversity pattern for microorganisms has received great attention recently but is still understudied, and phylogenetic relatedness is rarely studied for microbial elevational distributions. Using a bar-coded pyrosequencing technique, we examined the biodiversity patterns for soil bacterial communities of tundra ecosystem along 2000–2500 m elevations on Changbai Mountain in China. Bacterial taxonomic richness displayed a linear decreasing trend with increasing elevation. Phylogenetic diversity and mean nearest taxon distance (MNTD exhibited a unimodal pattern with elevation. Bacterial communities were more phylogenetically clustered than expected by chance at all elevations based on the standardized effect size of MNTD metric. The bacterial communities differed dramatically among elevations, and the community composition was significantly correlated with soil total carbon, total nitrogen, C:N ratio, and dissolved organic carbon. Multiple ordinary least squares regression analysis showed that the observed biodiversity patterns strongly correlated with soil total carbon and C:N ratio. Taken together, this is the first time that a significant bacterial diversity pattern has been observed across a small-scale elevational gradient. Our results indicated that soil carbon and nitrogen contents were the critical environmental factors affecting bacterial elevational distribution in Changbai Mountain tundra. This suggested that ecological niche-based environmental filtering processes related to soil carbon and nitrogen contents could play a dominant role in structuring bacterial communities along the elevational gradient.

Evaluating Swallowing Muscles Essential for Hyolaryngeal Elevation by Using Muscle Functional Magnetic Resonance Imaging

International Nuclear Information System (INIS)

Pearson, William G.; Hindson, David F.; Langmore, Susan E.; Zumwalt, Ann C.

2013-01-01

Purpose: Reduced hyolaryngeal elevation, a critical event in swallowing, is associated with radiation therapy. Two muscle groups that suspend the hyoid, larynx, and pharynx have been proposed to elevate the hyolaryngeal complex: the suprahyoid and longitudinal pharyngeal muscles. Thought to assist both groups is the thyrohyoid, a muscle intrinsic to the hyolaryngeal complex. Intensity modulated radiation therapy guidelines designed to preserve structures important to swallowing currently exclude the suprahyoid and thyrohyoid muscles. This study used muscle functional magnetic resonance imaging (mfMRI) in normal healthy adults to determine whether both muscle groups are active in swallowing and to test therapeutic exercises thought to be specific to hyolaryngeal elevation. Methods and Materials: mfMRI data were acquired from 11 healthy subjects before and after normal swallowing and after swallowing exercise regimens (the Mendelsohn maneuver and effortful pitch glide). Whole-muscle transverse relaxation time (T2 signal, measured in milliseconds) profiles of 7 test muscles were used to evaluate the physiologic response of each muscle to each condition. Changes in effect size (using the Cohen d measure) of whole-muscle T2 profiles were used to determine which muscles underlie swallowing and swallowing exercises. Results: Post-swallowing effect size changes (where a d value of >0.20 indicates significant activity during swallowing) for the T2 signal profile of the thyrohyoid was a d value of 0.09; a d value of 0.40 for the mylohyoid, 0.80 for the geniohyoid, 0.04 for the anterior digastric, and 0.25 for the posterior digastric-stylohyoid in the suprahyoid muscle group; and d values of 0.47 for the palatopharyngeus and 0.28 for the stylopharyngeus muscles in the longitudinal pharyngeal muscle group. The Mendelsohn maneuver and effortful pitch glide swallowing exercises showed significant effect size changes for all muscles tested, except for the thyrohyoid. Conclusions

Evaluating Swallowing Muscles Essential for Hyolaryngeal Elevation by Using Muscle Functional Magnetic Resonance Imaging

Energy Technology Data Exchange (ETDEWEB)

Pearson, William G., E-mail: bp1@bu.edu [Department of Anatomy and Neurobiology, Boston University School of Medicine, Boston, Massachusetts (United States); Hindson, David F. [Department of Radiology, Boston Medical Center, Boston, Massachusetts (United States); Langmore, Susan E. [Department of Otolaryngology, Boston Medical Center, Boston, Massachusetts (United States); Speech and Hearing Sciences, Boston University, Boston, Massachusetts (United States); Zumwalt, Ann C. [Department of Anatomy and Neurobiology, Boston University School of Medicine, Boston, Massachusetts (United States)

2013-03-01

Purpose: Reduced hyolaryngeal elevation, a critical event in swallowing, is associated with radiation therapy. Two muscle groups that suspend the hyoid, larynx, and pharynx have been proposed to elevate the hyolaryngeal complex: the suprahyoid and longitudinal pharyngeal muscles. Thought to assist both groups is the thyrohyoid, a muscle intrinsic to the hyolaryngeal complex. Intensity modulated radiation therapy guidelines designed to preserve structures important to swallowing currently exclude the suprahyoid and thyrohyoid muscles. This study used muscle functional magnetic resonance imaging (mfMRI) in normal healthy adults to determine whether both muscle groups are active in swallowing and to test therapeutic exercises thought to be specific to hyolaryngeal elevation. Methods and Materials: mfMRI data were acquired from 11 healthy subjects before and after normal swallowing and after swallowing exercise regimens (the Mendelsohn maneuver and effortful pitch glide). Whole-muscle transverse relaxation time (T2 signal, measured in milliseconds) profiles of 7 test muscles were used to evaluate the physiologic response of each muscle to each condition. Changes in effect size (using the Cohen d measure) of whole-muscle T2 profiles were used to determine which muscles underlie swallowing and swallowing exercises. Results: Post-swallowing effect size changes (where a d value of >0.20 indicates significant activity during swallowing) for the T2 signal profile of the thyrohyoid was a d value of 0.09; a d value of 0.40 for the mylohyoid, 0.80 for the geniohyoid, 0.04 for the anterior digastric, and 0.25 for the posterior digastric-stylohyoid in the suprahyoid muscle group; and d values of 0.47 for the palatopharyngeus and 0.28 for the stylopharyngeus muscles in the longitudinal pharyngeal muscle group. The Mendelsohn maneuver and effortful pitch glide swallowing exercises showed significant effect size changes for all muscles tested, except for the thyrohyoid. Conclusions

Buckling of Ship Structures

CERN Document Server

Shama, Mohamed

2013-01-01

Buckling of Ship Structures presents a comprehensive analysis of the buckling problem of ship structural members. A full analysis of the various types of loadings and stresses imposed on ship plating and primary and secondary structural members is given. The main causes and consequences of the buckling mode of failure of ship structure and the methods commonly used to control buckling failure are clarified. This book contains the main equations required to determine the critical buckling stresses for both ship plating and the primary and secondary stiffening structural members. The critical buckling stresses are given for ship plating subjected to the induced various types of loadings and having the most common boundary conditions encountered in ship structures.  The text bridges the gap existing in most books covering the subject of buckling of ship structures in the classical analytical format, by putting the emphasis on the practical methods required to ensure safety against buckling of ship structur...

P Elevator: An Innovatively Designed Elevator for Extraction of Third Molars.

Science.gov (United States)

Singh, Pradeep; Xiao, Shui Sheng; Ajmera, Deepal Haresh

2015-01-01

To modify the conventional straight elevator with a unique and innovative design in respect to approach and accessibility during extraction for patients with abrasions around corners of the mouth and with thick buccal mucosa, without causing overstretching of angles of the mouth. The shank of the straight elevator in the shape of a 'U' was modified, giving it a shape similar to 'P' in the English alphabet hence it is named the P Elevator. The P elevator utilises a 'U' shaped bend in the shank of the conventional straight elevator making space for the buccal soft tissues and the angle of the mouth, to accommodate properly in the 'U' shank. The application of this elevator in the successful removal of third molars is described. Two hundred patients underwent extraction of third molars with the P elevator including 166 patients with disimpaction of all third molars, 23 patients with abrasion around the angle of the mouth, and 11 patients with thick buccal mucosa. Satisfactory results were obtained in all the cases with no postoperative complications. The P elevator permits prudent, meticulous, innovative and proficient extraction of third molars in patients with thick buccal mucosa and abrasions around the angle of the mouth, without overstretching the corners of the mouth. We introduce novel applications of the P elevator in third molar extraction that provide substantial advantages over a conventional straight elevator.

Elevated sodium chloride concentrations enhance the bystander effects induced by low dose alpha-particle irradiation

International Nuclear Information System (INIS)

Han Wei; Zhu Lingyan; Jiang Erkang; Wang Jun; Chen Shaopeng; Bao Linzhi; Zhao Ye; Xu An; Yu Zengliang; Wu Lijun

2007-01-01

Previous studies have shown that high NaCl can be genotoxic, either alone or combined with irradiation. However, little is known about the relationship between environmental NaCl at elevated conditions and radiation-induced bystander effects (RIBE). RIBE, which has been considered as non-targeted bystander responses, has been demonstrated to occur widely in various cell lines. In the present study, RIBE under the elevated NaCl culture condition was assessed in AG 1522 cells by both the induction of γ-H2AX, a reliable marker of DNA double-strand break (DSB) for the early process ( G -methyl-L-arginine, an inhibitor of nitric oxide synthase, the induced fraction of foci-positive cells was effectively inhibited both in 0.2 cGy α-particle irradiated and adjacent non-irradiated regions under either normal or elevated NaCl conditions. These results suggested that the cultures with elevated NaCl medium magnified the damage effects induced by the low dose α-particle irradiation and nitric oxide generated by irradiation was also very important in this process

Michelson-Morley in Einstein's elevators

Science.gov (United States)

Pierce, Fred; Pierce, Ayal

2010-02-01

Experiments are proposed in which a Michelson-Morley interferometer is placed in Einstein's thought experiments where elevators are subjected to varied accelerated fields. Unbeknownst to the observers inside the elevators, they are placed in different circumstances: on the surface of the Earth, in free fall, in space distant from any mass, and inside a rotating space station. By use of not one, but two objects, the observer will be challenged to determine the nature and shape of the accelerated field, if any, inside the elevator. It will be demonstrated that the nature of the accelerated field can be determined easily from inside the elevator by the motion of the two objects released by the observer. It will also be shown that, for the elevator on the space station which is generating an ``artificial gravity'' field by rotation, Michelson-Morley would have the same null result as on Earth. However, the Michelson-Morley experiment is adapted so that in addition to the two horizontal arms of the interferometer (parallel to the floor of the elevator) a vertical arm is added perpendicular to the floor facing towards the ceiling. Such a vertical arm added to the Michelson-Morley experiment adds a new dimension to examining each accelerated field, including gravity. )

Structural Health Monitoring Based on Combined Structural Global and Local Frequencies

Directory of Open Access Journals (Sweden)

Jilin Hou

2014-01-01

Full Text Available This paper presents a parameter estimation method for Structural Health Monitoring based on the combined measured structural global frequencies and structural local frequencies. First, the global test is experimented to obtain the low order modes which can reflect the global information of the structure. Secondly, the mass is added on the member of structure to increase the local dynamic characteristic and to make the member have local primary frequency, which belongs to structural local frequency and is sensitive to local parameters. Then the parameters of the structure can be optimized accurately using the combined structural global frequencies and structural local frequencies. The effectiveness and accuracy of the proposed method are verified by the experiment of a space truss.

Structure-function relationship of a plant NCS1 member - Homology modeling and mutagenesis identified residues critical for substrate specificity of PLUTO, a nucleobase transporter from arabidopsis

KAUST Repository

Witz, Sandra; Panwar, Pankaj; Schober, Markus; Deppe, Johannes; Pasha, Farhan Ahmad; Lemieux, M. Joanne; Mö hlmann, Torsten

2014-01-01

. Furthermore, competition studies confirmed these results. The present study defines the molecular determinants for PLUTO substrate binding and demonstrates key differences in structure-function relations between PLUTO and other NCS1 family members. 2014 Witz

Determination of withdrawal resistance of staple joints constructed with various members of upholstered furniture

Directory of Open Access Journals (Sweden)

saeid Kazemi Najafi

2017-05-01

Full Text Available The goal of this study was to investigate the effects of joints members type (oriented strand lumber, plywood and poplar wood (Populusdeltoides, penetration deeps of staple (12 and 17mm and adhesives (with and without adhesive on face and edge withdrawal resistance of joints fabricated with staple. Experimental specimens under withdrawal load test of face and edge consisted of two principal structural members, main member and a secondary member which were joined together by one staple. The results showed that joint member, penetration deeps and adhesive significantly influence on the withdrawal resistance. Staple withdrawal resistance in the face was higher than that in the edge. Staple holding resistance increased with the increase of penetration deep and the withdrawal resistance of joints fabricated by adhesive was higher than those without adhesive. The joints made by oriented strand lumber exhibited better performance than other two members and joints made with poplar wood had higher resistance than plywood joints. The highest face (2326N and edge (1265N withdrawal resistances were obtained from joints prepared from oriented strand lumber with adhesive and17mm penetration deeps.

Legal frameworks and key concepts regulating diversion and treatment of mentally disordered offenders in European Union member states.

Science.gov (United States)

Dressing, Harald; Salize, Hans Joachim; Gordon, Harvey

2007-10-01

There is only limited research on the various legal regulations governing assessment, placement and treatment of mentally ill offenders in European Union member states (EU-member states). To provide a structured description and cross-boundary comparison of legal frameworks regulating diversion and treatment of mentally disordered offenders in EU-member states before the extension in May 2004. A special focus is on the concept of criminal responsibility. Information on legislation and practice concerning the assessment, placement and treatment of mentally ill offenders was gathered by means of a detailed, structured questionnaire which was filled in by national experts. The legal regulations relevant for forensic psychiatry in EU-member states are outlined. Definitions of mental disorders given within these acts are introduced and compared with ICD-10 diagnoses. Finally the application of the concept of criminal responsibility by the law and in routine practice is presented. Legal frameworks for the processing and placement of mentally disordered offenders varied markedly across EU-member states. Since May 2004 the European Union has expanded to 25 member states and in January 2007 it will reach 27. With increasing mobility across Europe, the need for increasing trans-national co-operation is becoming apparent in which great variation in legal tradition pertains.

The Members of the Agency

International Nuclear Information System (INIS)

2003-01-01

The document lists the 136 Member States of the Agency as of 6 May 2003. The new Members since the last issue of the list (INFCIRC/2/57) are Eritrea and the Republic of Seychelles. Cambodia withdrew from the Agency with effect from 26 March 2003. The dates on which the present 136 Member States became Members are given in an Attachment. It also shows the States whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute

Structure determination of organic compounds by 'electron pyrolysis'. Pt. 6

International Nuclear Information System (INIS)

Ege, G.; Gessner, K.; Schildknecht, H.

1977-01-01

By action of tritiated water on N-substituted 3-Amino-Δ 4 -thiazoline-2-ones and -2-thiones cleavage of the N-N-bond occurs with the formation of Δ 4 -thiazoline-2-ones and -2-thiones, respectively, and H 2 N-R 3 . Detection and identification of the fragments is performed by thin-layer chromatography and by comparison with authentic samples under the application of a radio-scanner. Such a fragmention is strong evidence for the five-membered ring structure. (orig.) [de

Preliminary structural integrity evaluations for the elevated temperature piping of the SFR IHTS against typical level a service events

International Nuclear Information System (INIS)

Park, Chang-Gyu; Kim, Jong-Bum; Lee, Jae-Han

2009-01-01

The SFR is adapting the IHTS(Intermediate Heat Transport System) to prevent the interaction of radioactive primary sodium and SG(Steam Generator) water. The IHTS hot leg piping connecting the IHX(Intermediate Heat eXchanger) to the SG of a 1200MWe pool-type SFR is an object component in this study. ASME Boiler and Pressure Vessel code Subsection NB provides rules for the design and analysis of the class 1 components. At an elevated temperature service, the ASME Subsection NH provides rules for the design and analysis of the Class 1 components but unfortunately, special rules for piping components are not provided until now. Therefore, the design and analysis of the IHTS hot leg piping shall comply with the design by analysis requirements of Subsection NH. The piping layout is proposed by considering the reactor component layout and reactor building space and the structural integrity is evaluated by considering two typical types of operating events in this study. Cycle type 1(CT-1) shows the refueling cycle event having a temperature history from a refueling temperature to a normal operating temperature via a hot standby temperature. Cycle type 2(CT-2) is a daily load follow operation. The structural integrity is evaluated by considering the enveloped CT-1 and CT-2 operating events per the ASME Subsection NH procedures. The SIE ASME-NH computer program, which has been developed to implement the ASME subsection NH rules, is used for the structural integrity evaluation by utilizing the finite element analysis results. (author)

The Analysis of the Relationship between Organizational Structure and Information Technology (IT): And the Barriers to Its Establishment at the University of Isfahan from the Faculty Member's Viewpoints

Science.gov (United States)

Peyman, Yarmohammadzadeh; Mohsen, Allammeh Sayyed; Hassan, Ghalavandi; Aboulghassim, Farhang; Zaman, Ajdari

2011-01-01

The purpose of the present study is to investigate the relationship between organizational structure between IT and the barriers to its establishment in University of Isfahan from faculty member's viewpoints in 2007-2008. The questionnaires were prepared and examined based on the organization dimensions of organizational structures (formality,…

An Exploratory Study of Student Service Members/Veterans' Mental Health Characteristics by Sexual Orientation.

Science.gov (United States)

Pelts, Michael D; Albright, David L

2015-01-01

Explore the mental health differences of student veterans by sexual orientation. Student service members/veterans (N = 702) from the Fall 2011 National College Health Assessment. Descriptive statistics and 2-sample proportion and mean tests were used to compare mental health characteristics. Student veterans who identify as lesbian, gay, bisexual, or unsure had higher levels of mental health symptoms and treatment. Results suggest a need for continued examination of student service members/veterans as related to disparities in mental health by sexual orientation.

Does a decade of elevated [CO2] affect a desert perennial plant community?

Science.gov (United States)

Newingham, Beth A; Vanier, Cheryl H; Kelly, Lauren J; Charlet, Therese N; Smith, Stanley D

2014-01-01

Understanding the effects of elevated [CO2 ] on plant community structure is crucial to predicting ecosystem responses to global change. Early predictions suggested that productivity in deserts would increase via enhanced water-use efficiency under elevated [CO2], but the response of intact arid plant communities to elevated [CO2 ] is largely unknown. We measured changes in perennial plant community characteristics (cover, species richness and diversity) after 10 yr of elevated [CO2] exposure in an intact Mojave Desert community at the Nevada Desert Free-Air CO2 Enrichment (FACE) Facility. Contrary to expectations, total cover, species richness, and diversity were not affected by elevated [CO2]. Over the course of the experiment, elevated [CO2] had no effect on changes in cover of the evergreen C3 shrub, Larrea tridentata; alleviated decreases in cover of the C4 bunchgrass, Pleuraphis rigida; and slightly reduced the cover of C3 drought-deciduous shrubs. Thus, we generally found no effect of elevated [CO2] on plant communities in this arid ecosystem. Extended drought, slow plant growth rates, and highly episodic germination and recruitment of new individuals explain the lack of strong perennial plant community shifts after a decade of elevated [CO2]. © 2013 The Authors. New Phytologist © 2013 New Phytologist Trust.

Ab initio investigation of the structure and nonlinear optical properties of five-membered heterocycles containing sulfur

International Nuclear Information System (INIS)

Spassova, Milena; Enchev, Venelin

2004-01-01

An ab initio HF and MP2 study of the static (hyper)polarizabilities of 2,4-substituted imidazoles and thiazoles is presented. The comparison of the two types of five-membered heterocycles suggests, that the exocyclic heteroatoms have much more influence upon the calculated hyperpolarizabilities, than the ring heteroatoms. It has been found, that adding diffuse functions to the 6-31G** basis set and inclusion of the electron correlation result in drastic changes in the second hyperpolarizability. The changes are more pronounced for the structures with larger number of sulfur atoms. A HF/6-31G** investigation of a push-pull system, in which thiorhodanine has been chosen as acceptor fragment shows an enhancement of the molecular polarizabilities with respect to the corresponding typical donor-acceptor NH 2 /NO 2 polyene

Elevated tropospheric CO2 and O3 concentrations impair organic pollutant removal from grassland soil.

Science.gov (United States)

Ai, Fuxun; Eisenhauer, Nico; Jousset, Alexandre; Butenschoen, Olaf; Ji, Rong; Guo, Hongyan

2018-04-03

The concentrations of tropospheric CO 2 and O 3 have been rising due to human activities. These rising concentrations may have strong impacts on soil functions as changes in plant physiology may lead to altered plant-soil interactions. Here, the effects of eCO 2 and eO 3 on the removal of polycyclic aromatic hydrocarbon (PAH) pollutants in grassland soil were studied. Both elevated CO 2 and O 3 concentrations decreased PAH removal with lowest removal rates at elevated CO 2 and elevated O 3 concentrations. This effect was linked to a shift in soil microbial community structure by structural equation modeling. Elevated CO 2 and O 3 concentrations reduced the abundance of gram-positive bacteria, which were tightly linked to soil enzyme production and PAH degradation. Although plant diversity did not buffer CO 2 and O 3 effects, certain soil microbial communities and functions were affected by plant communities, indicating the potential for longer-term phytoremediation approaches. Results of this study show that elevated CO 2 and O 3 concentrations may compromise the ability of soils to degrade organic pollutants. On the other hand, the present study also indicates that the targeted assembly of plant communities may be a promising tool to shape soil microbial communities for the degradation of organic pollutants in a changing world.

Elevated intrabolus pressure identifies obstructive processes when integrated relaxation pressure is normal on esophageal high-resolution manometry.

Science.gov (United States)

Quader, Farhan; Reddy, Chanakyaram; Patel, Amit; Gyawali, C Prakash

2017-07-01

esophageal HRM by raising suspicion for a structural EGJ process when IBP is elevated.

Mortality of male members of the Danish semiskilled workers' union. Standardization by county

DEFF Research Database (Denmark)

Jeune, B

1980-01-01

The mortality of male members of the Danish Semiskilled Workers' Union in 1973 has been analysed in an earlier publication. The aim of the present study was to see if previously indicated trends are being maintained after standardizing mortality rates by county for the period 1973-75. Although...... regional variations are seen, standardization by county produces only slight differences in age and cause-specific standardized mortality ratios. Earlier members of the Semiskilled Workers' Union, especially in younger age groups, are confirmed. Low mortality in older age groups, which show a deficit...... of deaths from circulatory diseases and other chronic illnesses, suggests the possibility of a survival population effect....

Structural inspection and wind analysis of redwood cooling towers at the Portsmouth Gaseous Diffusion Plant

International Nuclear Information System (INIS)

Chung, T.; Solack, T.; Hortel, J.

1991-01-01

As part of the plant upgrade program, structural analyses and field inspections were performed on four redwood cooling towers at the DOE Portsmouth gaseous diffusion plant located in Piketon, Ohio. The cooling towers are categorized as important hazard facilities. The loadings are derived from UCRL-15910 according to the pertinent hazard category. In addition to the seismic and wind loadings, the wood cooling towers are constantly subject to adverse environmental effects such as elevated temperature, chemical attack, icing and snow load, and motor vibrations. A thorough structural evaluation for all load combinations was performed for each of the cooling towers based on the structural code requirements of the Cooling Tower Institute and National Forest Products Association. Most stress criteria are unique for the redwood material. This evaluation was performed using finite element techniques on the global structural integrity and supplemented by hand calculations on the individual connection joints. Overloaded wood structural members and joints are identified by the analysis. The rectangular tower structure sits on a concrete basin that span across 60 ft by 200 ft. A major part of the cooling towers upgrading program involved field inspections of the individual cells of each tower. The primary purpose of these inspections was to identify any existing structural damage or deficiencies such as failed members, degraded wood, and deficiencies resulting from poor construction practice. Inspection of 40 cells identified some generic deficiencies that mostly are consistent with the analytical finding. Based on the analysis, some effective but inexpensive upgrading techniques were developed and recommended to bring the cooling towers into compliance with current DOE requirements

Crystal structure and potential physiological role of zebra fish thioesterase superfamily member 2 (fTHEM2)

Energy Technology Data Exchange (ETDEWEB)

Yu, Shanshan; Li, Han; Gao, Feng; Zhou, Ying, E-mail: zhouying@moon.ibp.ac.cn

2015-08-07

Thioesterase superfamily member 2 (THEM2) is an essential protein for mammalian cell proliferation. It belongs to the hotdog-fold thioesterase superfamily and catalyzes hydrolysis of thioester bonds of acyl-CoA in vitro, while its in vivo function remains unrevealed. In this study, Zebra fish was selected as a model organism to facilitate the investigations on THEM2. First, we solved the crystal structure of recombinant fTHEM2 at the resolution of 1.80 Å, which displayed a similar scaffolding as hTHEM2. Second, functional studies demonstrated that fTHEM2 is capable of hydrolyzing palmitoyl-CoA in vitro. In addition, injection of morpholino against fTHEM2 at one-cell stage resulted in distorted early embryo development, including delayed cell division, retarded development and increased death rate. The above findings validated our hypothesis that fTHEM2 could serve as an ideal surrogate for studying the physiological functions of THEM2. - Highlights: • The crystal structure of recombinant fTHEM2 is presented. • fTHEM2 is capable of hydrolyzing palmitoyl-CoA. • The influence of fTHEM2 on early embryo development is demonstrated.

Examining risk factors for cardiovascular disease among food bank members in Vancouver.

Science.gov (United States)

Fowokan, A O; Black, J L; Holmes, E; Seto, D; Lear, S A

2018-06-01

Food banks provide supplemental food to low-income households, yet little is known about the cardiovascular health of food banks members. This study therefore described cardiovascular disease (CVD) risk factors among food bank members and explored associations between food insecurity and CVD risk. Adults ≥18 years (n = 77) from three food bank sites in metro Vancouver, British Columbia completed surveys and physical assessments examining a range of socio-demographic variables and CVD risk factors. A composite measure of myocardial infarction (MI) risk called the INTERHEART score was assessed and household food insecurity was measured using the Household Food Security Survey Module. Regression models were used to explore associations between food insecurity and CVD risk measures, including the INTERHEART score. Ninety-seven percent of food bank members reported experiencing food insecurity, 65% were current smokers, 53% reported either chronic or several periods of stress in the past year, 55% reported low physical activity levels and 80% reported consuming fewer than five servings of fruit and vegetables daily. Prevalence of self-reported diabetes and hypertension were 13% and 29% respectively. Fifty-two percent of the sample were at high risk of non-fatal MI. No statistically significant associations were found between increased severity of food insecurity and CVD risk factors among this sample where both severe food insecurity and high CVD risks were prevalent. Food bank members were at elevated risk for CVD compared with the general population. Strategies are needed to reduce prevalence of food insecurity and CVD risk factors, both of which disproportionately affected food bank members.

Critical Technologies for the Development of Future Space Elevator Systems

Science.gov (United States)

Smitherman, David V., Jr.

2005-01-01

A space elevator is a tether structure extending through geosynchronous earth orbit (GEO) to the surface of the earth. Its center of mass is in GEO such that it orbits the earth in sync with the earth s rotation. In 2004 and 2005, the NASA Marshall Space Flight Center and the Institute for Scientific Research, Inc. worked under a cooperative agreement to research the feasibility of space elevator systems, and to advance the critical technologies required for the future development of space elevators for earth to orbit transportation. The discovery of carbon nanotubes in the early 1990's was the first indication that it might be possible to develop materials strong enough to make space elevator construction feasible. This report presents an overview of some of the latest NASA sponsored research on space elevator design, and the systems and materials that will be required to make space elevator construction possible. In conclusion, the most critical technology for earth-based space elevators is the successful development of ultra high strength carbon nanotube reinforced composites for ribbon construction in the 1OOGPa range. In addition, many intermediate technology goals and demonstration missions for the space elevator can provide significant advancements to other spaceflight and terrestrial applications.

Technical nursing students interacting with family members of hospitalized children

Directory of Open Access Journals (Sweden)

Juliana Yukari Takahashi Onishi

Full Text Available ABSTRACT Objective: To understand technical nursing students' meaning of interacting with family members of hospitalized children. Method: Symbolic Interactionism was used as the theoretical framework and Qualitative Content Analysis was the methodological procedure. A total of eight graduates from an institution situated in the city of Osasco, Sao Paulo state, participated in this study. Data were collected through semi-structured interviews. Results: A total of five representative themes were revealed: Dealing with difficult situations with family members; Perceiving oneself to be unprepared to interact with family members; Family members being a helpful tool; Developing strategies to obtain a good interaction with family members; and Teachers being facilitators of the interaction with family members. Final considerations: To be acquainted with this experience has led to the understanding of the need to include the theme of family care in the curriculum of the Technical Nursing Course. Additionally, the present study contributed to reflections on the importance of such knowledge for this population and to the development of future studies, as this theme has been scarcely explored in the literature.

Technical nursing students interacting with family members of hospitalized children.

Science.gov (United States)

Onishi, Juliana Yukari Takahashi; Ribeiro, Circéa Amália; Silva, Maria Cristina Ferreira Carlos Rodrigues da; Borba, Regina Issuzu Hirooka de

2017-01-01

To understand technical nursing students' meaning of interacting with family members of hospitalized children. Symbolic Interactionism was used as the theoretical framework and Qualitative Content Analysis was the methodological procedure. A total of eight graduates from an institution situated in the city of Osasco, Sao Paulo state, participated in this study. Data were collected through semi-structured interviews. A total of five representative themes were revealed: Dealing with difficult situations with family members; Perceiving oneself to be unprepared to interact with family members; Family members being a helpful tool; Developing strategies to obtain a good interaction with family members; and Teachers being facilitators of the interaction with family members. To be acquainted with this experience has led to the understanding of the need to include the theme of family care in the curriculum of the Technical Nursing Course. Additionally, the present study contributed to reflections on the importance of such knowledge for this population and to the development of future studies, as this theme has been scarcely explored in the literature.

24 CFR 960.204 - Denial of admission for criminal activity or drug abuse by household members.

Science.gov (United States)

2010-04-01

... activity or drug abuse by household members. 960.204 Section 960.204 Housing and Urban Development... HOUSING Admission § 960.204 Denial of admission for criminal activity or drug abuse by household members. (a) Required denial of admission—(1) Persons evicted for drug-related criminal activity. The PHA...

Investigation of isochronous stress-strain formulations for elevated temperature structural design

International Nuclear Information System (INIS)

Koo, Gyeong Hoi; Kim, Jong Bum

2012-01-01

For elevated temperature design evaluations by the ASME-NH rules, the most important material data is the isochronous stress-strain curves, which can provide design creep information. The main purpose of this paper is to investigate appropriate formulations to be able to generate the isochronous stress-strain curves and implement it to the computer program which is coded the ASME-NH design evaluation procedures. To do this, formulations by the strain-time relationship are investigated in detail and the sensitivity studies for rapid initial transient creep contributions, slower and longer transient creep contribution, and secondary creep contributions are carried out for type 316 austenitic stainless steel. From the results of this study, it is found that the strain-time relationship formulations can well describe the isochronous stress-strain curves with the transient creep contributions

The Members of the Agency

International Nuclear Information System (INIS)

2001-01-01

The new Members since the last list of Member States was issued (INFCIRC/2/Rev.54) are the Republic of Tajikistan, which deposited the instrument of acceptance of the Statute on 10 September 2001 and the Federal Republic of Yugoslavia, which deposited the instrument of acceptance of the Statute on 31 October 2001. The Attachment hereto shows the dates on which the present 133 Member States became Members. It also shows the States whose applications for membership of the Agency have been approved by the General Conference, but which have not yet deposited an instrument of acceptance of the Statute

The Members of the Agency

International Nuclear Information System (INIS)

1997-01-01

The document lists the 125 Member States of the Agency as of 1 September 1997. The new Member since the last issue of the list (INFCIRC/2/Rev.48) is Latvia. In an Attachment are given the dates on which the present 125 States became Members, the State (Republic of Moldova) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States (Malta and Burkina Faso) whose applications for membership have been recommended by the Board of Governors for approval by the General Conference

The Members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-22

The document lists the 125 Member States of the Agency as of 1 September 1997. The new Member since the last issue of the list (INFCIRC/2/Rev.48) is Latvia. In an Attachment are given the dates on which the present 125 States became Members, the State (Republic of Moldova) whose application for membership of the Agency has been approved by the General Conference but which has not yet deposited an instrument of acceptance of the Statute and the States (Malta and Burkina Faso) whose applications for membership have been recommended by the Board of Governors for approval by the General Conference.

Complex behavior of elevators in peak traffic

Science.gov (United States)

Nagatani, Takashi

2003-08-01

We study the dynamical behavior of elevators in the morning peak traffic. We present a stochastic model of the elevators to take into account the interactions between elevators through passengers. The dynamics of the elevators is expressed in terms of a coupled nonlinear map with noises. The number of passengers carried by an elevator and the time-headway between elevators exhibit the complex behavior with varying elevator trips. It is found that the behavior of elevators exhibits a deterministic chaos even if there are no noises. The chaotic motion depends on the loading parameter, the maximum capacity of an elevator, and the number of elevators. When the loading parameter is superior to the threshold, each elevator carries a full load of passengers throughout its trip. The dependence of the threshold (transition point) on the elevator capacity is clarified.

A Non-Member Spouse's Entitlement To The Member's Pension Interest

Directory of Open Access Journals (Sweden)

Motseotsile Clement Marumoagae

2014-12-01

Full Text Available It is important that married couples seek legal advice with regard to the assets falling within their joint estate, more particularly their retirement benefits. This article reflects on the entitlement (if any of non-member spouses to their spouses' retirement fund benefits. Pension benefits can be due before, during or after divorce, and parties to the marriage should be aware of their rights with regard to the accruing pension benefits of their spouses. While it is settled law that non-member spouses are entitled to receive a portion of their member spouses' pension benefits (known as "pension interest" immediately on divorce, it is not particularly clear whether non-member spouses are also entitled to receive the same before or sometime after divorce. In this article I provide a contextual understanding of the entitlements (if any which spouses or former spouses of members of pension funds have on such member spouses' retirement benefits. Furthermore, it shown in this article that various divisions of South African High Courts have been inconsistent in how they have approached the issue of the pension interest between divorcing spouses or divorced ex-spouses.

Polyketide synthase chemistry does not direct biosynthetic divergence between 9- and 10-membered enediynes

Science.gov (United States)

Horsman, Geoff P.; Chen, Yihua; Thorson, Jon S.; Shen, Ben

2010-01-01

Enediynes are potent antitumor antibiotics that are classified as 9- or 10-membered according to the size of the enediyne core structure. However, almost nothing is known about enediyne core biosynthesis, and the determinants of 9- versus 10-membered enediyne core biosynthetic divergence remain elusive. Previous work identified enediyne-specific polyketide synthases (PKSEs) that can be phylogenetically distinguished as being involved in 9- versus 10-membered enediyne biosynthesis, suggesting that biosynthetic divergence might originate from differing PKSE chemistries. Recent in vitro studies have identified several compounds produced by the PKSE and associated thioesterase (TE), but condition-dependent product profiles make it difficult to ascertain a true catalytic difference between 9- and 10-membered PKSE-TE systems. Here we report that PKSE chemistry does not direct 9- versus 10-membered enediyne core biosynthetic divergence as revealed by comparing the products from three 9-membered and two 10-membered PKSE-TE systems under identical conditions using robust in vivo assays. Three independent experiments support a common catalytic function for 9- and 10-membered PKSEs by the production of a heptaene metabolite from: (i) all five cognate PKSE-TE pairs in Escherichia coli; (ii) the C-1027 and calicheamicin cognate PKSE-TEs in Streptomyces lividans K4-114; and (iii) selected native producers of both 9- and 10-membered enediynes. Furthermore, PKSEs and TEs from different 9- and 10-membered enediyne biosynthetic machineries are freely interchangeable, revealing that 9- versus 10-membered enediyne core biosynthetic divergence occurs beyond the PKSE-TE level. These findings establish a starting point for determining the origins of this biosynthetic divergence. PMID:20534556

Journal Rankings by Health Management Faculty Members: Are There Differences by Rank, Leadership Status, or Area of Expertise?

Science.gov (United States)

Menachemi, Nir; Hogan, Tory H; DelliFraine, Jami L

2015-01-01

Health administration (HA) faculty members publish in a variety of journals, including journals focused on management, economics, policy, and information technology. HA faculty members are evaluated on the basis of the quality and quantity of their journal publications. However, it is unclear how perceptions of these journals vary by subdiscipline, department leadership role, or faculty rank. It is also not clear how perceptions of journals may have changed over the past decade since the last evaluation of journal rankings in the field was published. The purpose of the current study is to examine how respondents rank journals in the field of HA, as well as the variation in perception by academic rank, department leadership status, and area of expertise. Data were drawn from a survey of HA faculty members at U.S. universities, which was completed in 2012. Different journal ranking patterns were noted for faculty members of different subdisciplines. The health management-oriented journals (Health Care Management Review and Journal of Healthcare Management) were ranked higher than in previous research, suggesting that journal ranking perceptions may have changed over the intervening decade. Few differences in perceptions were noted by academic rank, but we found that department chairs were more likely than others to select Health Affairs in their top three most prestigious journals (β = 0.768; p journal prestige varied between a department chair and untenured faculty in different disciplines, and this perceived difference could have implications for promotion and tenure decisions.

Shake Table Testing of an Elevator System in a Full-Scale Five-Story Building.

Science.gov (United States)

Wang, Xiang; Hutchinson, Tara C; Astroza, Rodrigo; Conte, Joel P; Restrepo, José I; Hoehler, Matthew S; Ribeiro, Waldir

2017-03-01

This paper investigates the seismic performance of a functional traction elevator as part of a full-scale five-story building shake table test program. The test building was subjected to a suite of earthquake input motions of increasing intensity, first while the building was isolated at its base, and subsequently while it was fixed to the shake table platen. In addition, low-amplitude white noise base excitation tests were conducted while the elevator system was placed in three different configurations, namely, by varying the vertical location of its cabin and counterweight, to study the acceleration amplifications of the elevator components due to dynamic excitations. During the earthquake tests, detailed observation of the physical damage and operability of the elevator as well as its measured response are reported. Although the cabin and counterweight sustained large accelerations due to impact during these tests, the use of well-restrained guide shoes demonstrated its effectiveness in preventing the cabin and counterweight from derailment during high-intensity earthquake shaking. However, differential displacements induced by the building imposed undesirable distortion of the elevator components and their surrounding support structure, which caused damage and inoperability of the elevator doors. It is recommended that these aspects be explicitly considered in elevator seismic design.

Skin peptide tyrosine-tyrosine, a member of the pancreatic polypeptide family: isolation, structure, synthesis, and endocrine activity.

Science.gov (United States)

Mor, A; Chartrel, N; Vaudry, H; Nicolas, P

1994-10-25

Pancreatic polypeptide, peptide tyrosine-tyrosine (PYY), and neuropeptide tyrosine (NPY), three members of a family of structurally related peptides, are mainly expressed in the endocrine pancreas, in endocrine cells of the gut, and in the brain, respectively. In the present study, we have isolated a peptide of the pancreatic polypeptide family from the skin of the South American arboreal frog Phyllomedusa bicolor. The primary structure of the peptide was established as Tyr-Pro-Pro-Lys-Pro-Glu-Ser-Pro-Gly-Glu10-Asp-Ala-Ser-Pro-Glu-Glu- Met-Asn- Lys-Tyr20-Leu-Thr-Ala-Leu-Arg-His-Tyr-Ile-Asn-Leu30-Val-Thr- Arg-Gln-Arg-Tyr-NH2 . This unusual peptide, named skin peptide tyrosine-tyrosine (SPYY), exhibits 94% similarity with PYY from the frog Rana ridibunda. A synthetic replicate of SPYY inhibits melanotropin release from perifused frog neurointermediate lobes in very much the same way as NPY. These results demonstrate the occurrence of a PYY-like peptide in frog skin. Our data also suggest the existence of a pituitary-skin regulatory loop in amphibians.

Towards large-scale mapping of urban three-dimensional structure using Landsat imagery and global elevation datasets

Science.gov (United States)

Wang, P.; Huang, C.

2017-12-01

The three-dimensional (3D) structure of buildings and infrastructures is fundamental to understanding and modelling of the impacts and challenges of urbanization in terms of energy use, carbon emissions, and earthquake vulnerabilities. However, spatially detailed maps of urban 3D structure have been scarce, particularly in fast-changing developing countries. We present here a novel methodology to map the volume of buildings and infrastructures at 30 meter resolution using a synergy of Landsat imagery and openly available global digital surface models (DSMs), including the Shuttle Radar Topography Mission (SRTM), ASTER Global Digital Elevation Map (GDEM), ALOS World 3D - 30m (AW3D30), and the recently released global DSM from the TanDEM-X mission. Our method builds on the concept of object-based height profile to extract height metrics from the DSMs and use a machine learning algorithm to predict height and volume from the height metrics. We have tested this algorithm in the entire England and assessed our result using Lidar measurements in 25 England cities. Our initial assessments achieved a RMSE of 1.4 m (R2 = 0.72) for building height and a RMSE of 1208.7 m3 (R2 = 0.69) for building volume, demonstrating the potential of large-scale applications and fully automated mapping of urban structure.

The Members of the Agency

International Nuclear Information System (INIS)

1995-01-01

The new member since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.44) is Yemen. The Attachment hereto shows the dates on which the 122 States became members of the Agency, as well as the State whose application for membership of the Agency was approved by the General Conference, but which has not yet deposited an instrument of acceptance of the Statute

The Members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-02-13

The new member since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.44) is Yemen. The Attachment hereto shows the dates on which the 122 States became members of the Agency, as well as the State whose application for membership of the Agency was approved by the General Conference, but which has not yet deposited an instrument of acceptance of the Statute.

IMPACTS OF INTERACTING ELEVATED ATMOSPHERIC CO2 AND O3 ON THE STRUCTURE AND FUNCTIONING OF A NORTHERN FOREST ECOSYSTEM: OPERATING AND DECOMMISSIONING THE ASPEN FACE PROJECT

Energy Technology Data Exchange (ETDEWEB)

Burton, Andrew J. [Michigan Technological University; Zak, Donald R. [University of Michigan; Kubiske, Mark E. [USDA Forest Service; Pregitzer, Kurt S. [University of Idaho

2014-06-30

Two of the most important and pervasive greenhouse gases driving global change and impacting forests in the U.S. and around the world are atmospheric CO2 and tropospheric O3. As the only free air, large-scale manipulative experiment studying the interaction of elevated CO2 and O3 on forests, the Aspen FACE experiment was uniquely designed to address the long-term ecosystem level impacts of these two greenhouse gases on aspen-birch-maple forests, which dominate the richly forested Lake States region. The project was established in 1997 to address the overarching scientific question: “What are the effects of elevated [CO2] and [O3], alone and in combination, on the structure and functioning of northern hardwood forest ecosystems?” From 1998 through the middle of the 2009 growing season, we examined the interacting effects of elevated CO2 and O3 on ecosystem processes in an aggrading northern forest ecosystem to compare the responses of early-successional, rapid-growing shade intolerant trembling aspen and paper birch to those of a late successional, slower growing shade tolerant sugar maple. Fumigations with elevated CO2 (560 ppm during daylight hours) and O3 (approximately 1.5 x ambient) were conducted during the growing season from 1998 to 2008, and in 2009 through harvest date. Response variables quantified during the experiment included growth, competitive interactions and stand dynamics, physiological processes, plant nutrient status and uptake, tissue biochemistry, litter quality and decomposition rates, hydrology, soil respiration, microbial community composition and respiration, VOC production, treatment-pest interactions, and treatment-phenology interactions. In 2009, we conducted a detailed harvest of the site. The harvest included detailed sampling of a subset of trees by component (leaves and buds, fine branches, coarse branches and stem, coarse roots, fine roots) and excavation of soil to a depth of 1 m. Throughout the experiment, aspen and birch

Experimental Study of Axially Tension Cold Formed Steel Channel Members

Science.gov (United States)

Apriani, Widya; Lubis, Fadrizal; Angraini, Muthia

2017-12-01

Experimental testing is commonly used as one of the steps to determine the cause of the collapse of a building structure. The collapse of structures can be due to low quality materials. Although material samples have passed laboratory tests and the existing technical specifications have been met but there may be undetected defects and known material after failure. In this paper will be presented Experimental Testing of Axially Tension Cold Formed Steel Channel Members to determine the cause of the collapse of a building roof truss x in Pekanbaru. Test of tensile strength material cold formed channel sections was performed to obtain the main characteristics of Cold Formed steel material, namely ultimate tensile strength loads that can be held by members and the yield stress possessed by channel sections used in construction. Analysis of axially tension cold formed steel channel section presents in this paper was conducted through experimental study based on specificationsAnnualBook of ASTM Standards: Metal Test methods and Analitical Procedures, Section 3 (1991). The result of capacity loads experimental test was compared with design based on SNI 03-7971-2013standard of Indonesia for the design of cold formed steel structural members. The results of the yield stress of the material will be seen against the minimum allowable allowable stress range. After the test, the percentace of ultimate axial tension capacity theory has a result that is 16.46% larger than the ultimate axial tension capacity experimental. When compared with the load that must be borne 5.673 kN/m it can be concluded that 2 specimens do not meet. Yield stress of member has fulfilled requirement that wass bigger than 550 MPa. Based on the curve obtained ultimate axial tension capacity theory, results greater than experimental. The greatest voltage value (fu) is achieved under the same conditions as its yield stress. For this specimen with a melting voltage value fy = 571.5068 MPa has fulfilled the

Energy efficient elevators and escalators

Energy Technology Data Exchange (ETDEWEB)

Patrao, Carlos; Fong, Joao; Almeida, Anibal de (Dep. Electrical Engineering, Univ. of Coimbra, Coimbra (Portugal)); Rivet, Luc

2009-07-01

Elevators and escalators are the crucial element that makes it practical to live and work several floors above ground - more than 4,3 million units are installed in Europe. Due to ageing of the European population the installation of elevators in single family houses is experiencing a significant growth, as well as equipping existing buildings. Elevators use about 4% of the electricity in tertiary sector buildings. High untapped saving potentials exist with respect to energy-efficient technologies, investment decisions and behavioural approaches, in these sectors. This paper presents preliminary results from the IEE project E4, whose overall objective is the improvement of the energy performance of elevators and escalators, in tertiary sector buildings and in multi family residential buildings. The project is characterizing people conveyors electricity consumption in the tertiary sector and in residential buildings in the EU. The installed park is characterised by a survey among elevators national associations in each country. An assessment of the barriers has been made in the first phase of the project and will be presented. Monitoring campaigns in elevators and escalators are being conducted in each country according to a common developed methodology. More than fifty elevators and escalators will be audited. This will allow the collection of load curves (start up, travel up and down, travel full and empty), including the characterization of standby consumption. Standby consumption of an elevator can represent up to 80% of the total energy consumed per year, and can be drastically reduced. This paper presents the preliminary results of the first ten audits performed in Portugal by Isr-UC.

Elevated gamma-rays shielding property in lead-free bismuth tungstate by nanofabricating structures

Science.gov (United States)

Liu, Jun-Hua; Zhang, Quan-Ping; Sun, Nan; Zhao, Yang; Shi, Rui; Zhou, Yuan-Lin; Zheng, Jian

2018-01-01

Radiation shielding materials have attracted much attention across academia and industry because of the increasing of nuclear activities. To achieve the materials with low toxicity but good protective capability is one of the most significant goals for personal protective articles. Here, bismuth tungstate nanostructures are controllably fabricated by a versatile hydrothermal treatment under various temperatures. The crystals structure and morphology of products are detailedly characterized with X-ray diffraction, electron microscope and specific surface area. It is noteworthy that desired Bi2WO6 nanosheets treated with 190 °C show the higher specific surface area (19.5 m2g-1) than that of the other two products. Importantly, it has a close attenuating property to lead based counterpart for low energy gamma-rays. Due to the less toxicity, Bi2WO6 nanosheets are more suitable than lead based materials to fabricate personal protective articles for shielding low energy radiations and have great application prospect as well as market potential.

Design considerations for CRBRP heat transport system piping operating at elevated temperatures

International Nuclear Information System (INIS)

Pollono, L.P.; Mello, R.M.

1979-01-01

The heat transport system sodium piping for the Clinch River Breeder Reactor Plant (CRBRP) within the reactor containment building must withstand high temperatures for long periods of time. Each phase of the mechanical design process of the piping system is influenced by elevated temperature considerations which include material thermal creep effects, ratchetting caused by rapid temperature transients and stress relaxation, and material degradation effects. The structural design philosophy taken to design the CRBRP piping operating in a high temperature environment is described. The resulting design of the heat transport system piping is presented along with a discussion of special features that resulted from the elevated temperature considerations

Down-regulation of tissue N:P ratios in terrestrial plants by elevated CO2.

Science.gov (United States)

Deng, Qi; Hui, Dafeng; Luo, Yiqi; Elser, James; Wang, Ying-ping; Loladze, Irakli; Zhang, Quanfa; Dennis, Sam

2015-12-01

Increasing atmospheric CO2 concentrations generally alter element stoichiometry in plants. However, a comprehensive evaluation of the elevated CO2 impact on plant nitrogen: phosphorus (N:P) ratios and the underlying mechanism has not been conducted. We synthesized the results from 112 previously published studies using meta-analysis to evaluate the effects of elevated CO2 on the N:P ratio of terrestrial plants and to explore the underlying mechanism based on plant growth and soil P dynamics. Our results show that terrestrial plants grown under elevated CO2 had lower N:P ratios in both above- and belowground biomass across different ecosystem types. The response ratio for plant N:P was negatively correlated with the response ratio for plant growth in croplands and grasslands, and showed a stronger relationship for P than for N. In addition, the CO2-induced down-regulation of plant N:P was accompanied by 19.3% and 4.2% increases in soil phosphatase activity and labile P, respectively, and a 10.1% decrease in total soil P. Our results show that down-regulation of plant N:P under elevated CO2 corresponds with accelerated soil P cycling. These findings should be useful for better understanding of terrestrial plant stoichiometry in response to elevated CO2 and of the underlying mechanisms affecting nutrient dynamics under climate change.

Signatures of self-assembly in size distributions of wood members in dam structures of Castor canadensis

Directory of Open Access Journals (Sweden)

David M. Blersch

2014-12-01

Full Text Available Beavers (Castor canadensis construct dams on rivers throughout most of their historical range in North America, and their impact on water patterns in the landscape is considerable. Dam formation by beavers involves two processes: (1 intentional construction through the selection and placement of wood and sediment, which facilitates (2 the passive capture and accretion of suspended wood and sediment. The second process is a self-assembly mechanism that the beavers leverage by utilizing energy subsidies of watershed transport processes. The relative proportion of beaver activity to self-assembly processes in dam construction, however, is unknown. Here we show that lotic self-assembly processes account for a substantial portion of the work expended in beaver dam construction. We found through comprehensive measurement of the stick dimensions that the distributions for diameter, length, and volume are log-normal. By noting evidence of teeth markings, we determined that size distributions skewed significantly larger for wood handled by beavers compared to those that were not. Subsequent mass calculations suggest that beavers perform 50%–70% of the work of wood member placement for dam assembly, with riparian self-assembly processes contributing the remainder. Additionally, our results establish a benchmark for assessing the proportion of self-assembly work in similar riparian structures. Keywords: Beaver dam, Construction, Castor canadensis, Self-assembly, Distribution, Wood

Nitrogen fertilization has a stronger effect on soil nitrogen-fixing bacterial communities than elevated atmospheric CO2.

Science.gov (United States)

Berthrong, Sean T; Yeager, Chris M; Gallegos-Graves, Laverne; Steven, Blaire; Eichorst, Stephanie A; Jackson, Robert B; Kuske, Cheryl R

2014-05-01

Biological nitrogen fixation is the primary supply of N to most ecosystems, yet there is considerable uncertainty about how N-fixing bacteria will respond to global change factors such as increasing atmospheric CO2 and N deposition. Using the nifH gene as a molecular marker, we studied how the community structure of N-fixing soil bacteria from temperate pine, aspen, and sweet gum stands and a brackish tidal marsh responded to multiyear elevated CO2 conditions. We also examined how N availability, specifically, N fertilization, interacted with elevated CO2 to affect these communities in the temperate pine forest. Based on data from Sanger sequencing and quantitative PCR, the soil nifH composition in the three forest systems was dominated by species in the Geobacteraceae and, to a lesser extent, Alphaproteobacteria. The N-fixing-bacterial-community structure was subtly altered after 10 or more years of elevated atmospheric CO2, and the observed shifts differed in each biome. In the pine forest, N fertilization had a stronger effect on nifH community structure than elevated CO2 and suppressed the diversity and abundance of N-fixing bacteria under elevated atmospheric CO2 conditions. These results indicate that N-fixing bacteria have complex, interacting responses that will be important for understanding ecosystem productivity in a changing climate.

Design of a powered elevator control system. [powered elevator system for modified C-8A aircraft for STOL operation

Science.gov (United States)

Glende, W. L. B.

1974-01-01

The design, fabrication and flight testing of a powered elevator system for the Augmentor Wing Jet STOL Research Aircraft (AWJSRA or Mod C-8A) are discussed. The system replaces a manual spring tab elevator control system that was unsatisfactory in the STOL flight regime. Pitch control in the AWJSRA is by means of a single elevator control surface. The elevator is used for both maneuver and trim control as the stabilizer is fixed. A fully powered, irreversible flight control system powered by dual hydraulic sources was designed. The existing control columns and single mechanical cable system of the AWJSRA have been retained as has been the basic elevator surface, except that the elevator spring tab is modified into a geared balance tab. The control surface is directly actuated by a dual tandem moving body actuator. Control signals are transmitted from the elevator aft quadrant to the actuator by a linkage system that includes a limited authority series servo actuator.

Elevated sodium chloride concentrations enhance the bystander effects induced by low dose alpha-particle irradiation

Energy Technology Data Exchange (ETDEWEB)

Han Wei; Zhu Lingyan; Jiang Erkang; Wang Jun; Chen Shaopeng; Bao Linzhi; Zhao Ye; Xu An; Yu Zengliang [Key Laboratory of Ion Beam Bioengineering, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Wu Lijun [Key Laboratory of Ion Beam Bioengineering, Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China)], E-mail: ljw@ipp.ac.cn

2007-11-01

Previous studies have shown that high NaCl can be genotoxic, either alone or combined with irradiation. However, little is known about the relationship between environmental NaCl at elevated conditions and radiation-induced bystander effects (RIBE). RIBE, which has been considered as non-targeted bystander responses, has been demonstrated to occur widely in various cell lines. In the present study, RIBE under the elevated NaCl culture condition was assessed in AG 1522 cells by both the induction of {gamma}-H2AX, a reliable marker of DNA double-strand break (DSB) for the early process (<1 h post irradiation), and the generation of micronuclei (MN), a sensitive marker for relative long process of RIBE. Our results showed that in the absence of irradiation, NaCl at elevated concentration such as 8.0, 9.0 and 10.0 g/L did not significantly increase the frequency of {gamma}-H2AX foci-positive cells and the number of foci per positive cell comparing with that NaCl at a normal concentration (6.8 g/L). However, with 0.2 cGy {alpha}-particle irradiation, the induced fraction of {gamma}-H2AX foci-positive cells and the number of induced {gamma}-H2AX foci per positive cell were significantly increased in both irradiated and adjacent non-irradiated regions. Similarly, the induction of MN by 0.2 cGy {alpha}-particle irradiation also increased with the elevated NaCl concentrations. With N{sup G}-methyl-L-arginine, an inhibitor of nitric oxide synthase, the induced fraction of foci-positive cells was effectively inhibited both in 0.2 cGy {alpha}-particle irradiated and adjacent non-irradiated regions under either normal or elevated NaCl conditions. These results suggested that the cultures with elevated NaCl medium magnified the damage effects induced by the low dose {alpha}-particle irradiation and nitric oxide generated by irradiation was also very important in this process.

A follow-up meeting post death is appreciated by family members of deceased patients.

Science.gov (United States)

Kock, M; Berntsson, C; Bengtsson, A

2014-08-01

A practice with a follow-up meeting post death (FUMPD) with physician and staff for family members of patients who died in the intensive care unit (ICU) was started as a quality project to improve the support of families in post-ICU bereavement. A quality improvement control was conducted after 4 years. The quality improvement control was made retrospectively as an anonymous non-coded questionnaire. Part A related to the FUMPD. Part B inquired if we could contact the family member again for a research project to evaluate family support post-ICU bereavement. The questionnaires were sent to 84 family members of 56 deceased patients. Part A: 46 out of 84 family members answered and had attended a FUMPD. Ninety-one percent of the family members thought that we should continue to offer FUMPD. Seventy-eight percent were satisfied with their meeting. Eighty percent felt that they understood the cause of death. The majority wanted the meeting to take place within 6 weeks of death. Ninety-one percent rated the physician as important to be present at the meeting. The social worker was rated more important to attend the meeting than the assistant nurse. Ninety-one percent wanted to discuss the cause of death.Part B: 54 out of 84 family members answered. Twenty out of 54 did not want us to contact them again. A routine with a Follow-Up Meeting Post Death with the ICU team for the families of the patients who die in the ICU is appreciated. The presence of the physician is important. © 2014 The Acta Anaesthesiologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Members of the Agency

International Nuclear Information System (INIS)

2007-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.63) is Palau which deposited its Instrument of Acceptance of the Statute on 2 March 2007. The Attachment hereto shows the dates on which the present 144 Member States became Members [fr

Members of the Agency

International Nuclear Information System (INIS)

2007-01-01

The new Member since the last list of Member States was issued (INFCIRC/2/Rev.63) is Palau which deposited its Instrument of Acceptance of the Statute on 2 March 2007. The Attachment hereto shows the dates on which the present 144 Member States became Members [es

The Members of the Agency

International Nuclear Information System (INIS)

1999-01-01

The document lists the 129 Member States of the Agency as of 1 June 1999. The new Member since the last issue of the list (INFCIRC/2/51) is Benin. The dates on which the present 129 states became Members, and the state (Honduras) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 43rd session of the General Conference are given in an Attachment

The Members of the Agency

International Nuclear Information System (INIS)

1998-01-01

The document lists the 128 Member States of the Agency as of 18 September 1998. The new Member since the last issue of the list (INFCIRC/2/50) is Burkina Faso. In an attachment the dates on which the present 128 states became Members, and the state (Benin) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 42nd session of the General Conference are given

The Members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-18

The document lists the 128 Member States of the Agency as of 18 September 1998. The new Member since the last issue of the list (INFCIRC/2/50) is Burkina Faso. In an attachment the dates on which the present 128 states became Members, and the state (Benin) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 42nd session of the General Conference are given

The Members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-16

The document lists the 129 Member States of the Agency as of 1 June 1999. The new Member since the last issue of the list (INFCIRC/2/51) is Benin. The dates on which the present 129 states became Members, and the state (Honduras) whose application for membership of the Agency has been recommended by the Board of Governors to be considered at the 43rd session of the General Conference are given in an Attachment.

Elevational Variation in Soil Amino Acid and Inorganic Nitrogen Concentrations in Taibai Mountain, China.

Directory of Open Access Journals (Sweden)

Xiaochuang Cao

Full Text Available Amino acids are important sources of soil organic nitrogen (N, which is essential for plant nutrition, but detailed information about which amino acids predominant and whether amino acid composition varies with elevation is lacking. In this study, we hypothesized that the concentrations of amino acids in soil would increase and their composition would vary along the elevational gradient of Taibai Mountain, as plant-derived organic matter accumulated and N mineralization and microbial immobilization of amino acids slowed with reduced soil temperature. Results showed that the concentrations of soil extractable total N, extractable organic N and amino acids significantly increased with elevation due to the accumulation of soil organic matter and the greater N content. Soil extractable organic N concentration was significantly greater than that of the extractable inorganic N (NO3--N + NH4+-N. On average, soil adsorbed amino acid concentration was approximately 5-fold greater than that of the free amino acids, which indicates that adsorbed amino acids extracted with the strong salt solution likely represent a potential source for the replenishment of free amino acids. We found no appreciable evidence to suggest that amino acids with simple molecular structure were dominant at low elevations, whereas amino acids with high molecular weight and complex aromatic structure dominated the high elevations. Across the elevational gradient, the amino acid pool was dominated by alanine, aspartic acid, glycine, glutamic acid, histidine, serine and threonine. These seven amino acids accounted for approximately 68.9% of the total hydrolyzable amino acid pool. The proportions of isoleucine, tyrosine and methionine varied with elevation, while soil major amino acid composition (including alanine, arginine, aspartic acid, glycine, histidine, leucine, phenylalanine, serine, threonine and valine did not vary appreciably with elevation (p>0.10. The compositional

Topobathymetric elevation model development using a new methodology: Coastal National Elevation Database

Science.gov (United States)

Danielson, Jeffrey J.; Poppenga, Sandra K.; Brock, John C.; Evans, Gayla A.; Tyler, Dean; Gesch, Dean B.; Thatcher, Cindy A.; Barras, John

2016-01-01

During the coming decades, coastlines will respond to widely predicted sea-level rise, storm surge, and coastalinundation flooding from disastrous events. Because physical processes in coastal environments are controlled by the geomorphology of over-the-land topography and underwater bathymetry, many applications of geospatial data in coastal environments require detailed knowledge of the near-shore topography and bathymetry. In this paper, an updated methodology used by the U.S. Geological Survey Coastal National Elevation Database (CoNED) Applications Project is presented for developing coastal topobathymetric elevation models (TBDEMs) from multiple topographic data sources with adjacent intertidal topobathymetric and offshore bathymetric sources to generate seamlessly integrated TBDEMs. This repeatable, updatable, and logically consistent methodology assimilates topographic data (land elevation) and bathymetry (water depth) into a seamless coastal elevation model. Within the overarching framework, vertical datum transformations are standardized in a workflow that interweaves spatially consistent interpolation (gridding) techniques with a land/water boundary mask delineation approach. Output gridded raster TBDEMs are stacked into a file storage system of mosaic datasets within an Esri ArcGIS geodatabase for efficient updating while maintaining current and updated spatially referenced metadata. Topobathymetric data provide a required seamless elevation product for several science application studies, such as shoreline delineation, coastal inundation mapping, sediment-transport, sea-level rise, storm surge models, and tsunami impact assessment. These detailed coastal elevation data are critical to depict regions prone to climate change impacts and are essential to planners and managers responsible for mitigating the associated risks and costs to both human communities and ecosystems. The CoNED methodology approach has been used to construct integrated TBDEM models

Foam rigidized inflatable structural assemblies

Science.gov (United States)

Tinker, Michael L. (Inventor); Schnell, Andrew R. (Inventor)

2010-01-01

An inflatable and rigidizable structure for use as a habitat or a load bearing structure is disclosed. The structure consists of an outer wall and an inner wall defining a containment member and a bladder. The bladder is pressurized to erect the structure from an initially collapsed state. The containment member is subsequently injected with rigidizable fluid through an arrangement of injection ports. Exhaust gases from the curing rigidizable fluid are vented through an arrangement of exhaust ports. The rate of erection can be controlled by frictional engagement with a container or by using a tether. A method for fabricating a tubular structure is disclosed.

Stress-coping morbidity among family members of addiction patients in Singapore.

Science.gov (United States)

Lee, Kae Meng Thomas; Manning, Victoria; Teoh, Hui Chin; Winslow, Munidasa; Lee, Arthur; Subramaniam, Mythily; Guo, Song; Wong, Kim Eng

2011-07-01

INTRODUCTIONS AND AIMS: Research from western countries indicates that family members of addiction patients report heightened stress and psychological morbidity. This current study aimed to examine stress, coping behaviours, related morbidity and subsequent resource utilisation among family members of patients attending a national treatment program in Singapore. The study used a matched case-control design. One hundred family members of addiction patients attending treatment and 100 matched controls completed a semi-structured interview with a researcher. This included the Beck Depression Inventory-II, Short-Form Health Survey-36, General Health Questionnaire-28, Perceived Stress Scale, Family Member Impact Scale and Coping Questionnaire, and also assessed service utilisation. T-tests revealed significantly greater depression, stress and psychiatric morbidity and poorer overall well-being (Short-Form Health Survey-36) among family members compared with controls. Despite the apparent negative impact on mental health, their physical morbidity did not differ from controls and services utilisation was low. Tolerant-inactive coping was found to be most strongly correlated with psychological well-being. Multivariate analysis indicated that perceived stress was the strongest predictor of overall strain (General Health Questionnaire), but this was not moderated by coping style. Subjective appraisal of stress and coping responses are essential factors affecting the morbidity of family members. Family members demonstrated a need and willingness to engage in formal treatment/counselling for their own problems that were attributed to living with an addiction patient. This provides an opportunity for stress management and brief interventions to modify coping styles, thereby minimizing the potential negative mental health impact on family members. © 2011 Australasian Professional Society on Alcohol and other Drugs.

Stepping Up: Burden Sharing by NATO’s Newest Members

Science.gov (United States)

2014-11-01

trustworthiness as a partner in Bosnia and Herzegovina, Kosovo, Af- ghanistan, and also in Iraq. Now, as a full member of the Alliance, our responsibility in...Rein Lang at the celebrating of the first anniversary of Estonia’s NATO accession,” Tallinn, Estonia, April 4, 2005, available from www.vm.ee/eng...Lang, Rein (Estonian Foreign Minister). “Address by Foreign Minister Rein Lang at the celebration of the first anniversary of Estonia’s NATO accession

Improvements in or relating to the manufacture of superconducting members

International Nuclear Information System (INIS)

Lee, J.A.; Madsen, P.E.; Hills, R.F.

1980-01-01

A method is described for the manufacture of superconducting members; more particularly of a superconducting member comprising a large number of fine superconductive filaments supported in an electrically conductive, non-superconductive matrix. The method embodies a superconductor of A 15 crystal structure having the general formula A 3 B (where A is a substrate metal (preferably niobium or vanadium) and B is one or more elements (e.g. tin, germanium) which when alloyed with A will form the superconductor). The method involves, as one step, forming an alloy of a carrier metal (e.g. copper) with the element B, and an essential condition of the method is that the phosphorus content of the alloy is less than 0.2 per cent by weight. (U.K.)

Similar variation in carbon storage between deciduous and evergreen treeline species across elevational gradients.

Science.gov (United States)

Fajardo, Alex; Piper, Frida I; Hoch, Günter

2013-08-01

The most plausible explanation for treeline formation so far is provided by the growth limitation hypothesis (GLH), which proposes that carbon sinks are more restricted by low temperatures than by carbon sources. Evidence supporting the GLH has been strong in evergreen, but less and weaker in deciduous treeline species. Here a test is made of the GLH in deciduous-evergreen mixed species forests across elevational gradients, with the hypothesis that deciduous treeline species show a different carbon storage trend from that shown by evergreen species across elevations. Tree growth and concentrations of non-structural carbohydrates (NSCs) in foliage, branch sapwood and stem sapwood tissues were measured at four elevations in six deciduous-evergreen treeline ecotones (including treeline) in the southern Andes of Chile (40°S, Nothofagus pumilio and Nothofagus betuloides; 46°S, Nothofagus pumilio and Pinus sylvestris) and in the Swiss Alps (46°N, Larix decidua and Pinus cembra). Tree growth (basal area increment) decreased with elevation for all species. Regardless of foliar habit, NSCs did not deplete across elevations, indicating no shortage of carbon storage in any of the investigated tissues. Rather, NSCs increased significantly with elevation in leaves (P treeline species are sink limited when faced with decreasing temperatures. Despite the overall higher requirements of deciduous tree species for carbon storage, no indication was found of carbon limitation in deciduous species in the alpine treeline ecotone.

Minnesota Multiphasic Personality Inventory-2-Restructured Form (MMPI-2-RF) normative elevation rates: comparisons with epidemiological prevalence rates.

Science.gov (United States)

Tarescavage, Anthony M; Marek, Ryan J; Finn, Jacob A; Hicks, Adam; Rapier, Jessica L; Ben-Porath, Yossef S

2013-01-01

Odland, Berthelson, Sharma, Martin, and Mittenberg ( 2013 ) caution that clinically elevated scale scores produced by members of the Minnesota Multiphasic Personality Inventory-2-Restructured Form (MMPI-2-RF; Ben-Porath & Tellegen, 2008 /2011) normative sample raise concerns about the potential for false positive findings of psychopathology. However, the MMPI-2-RF normative sample is intended to represent the general population of the United States, 26.2% of which met criteria for a Diagnostic and Statistical Manual-IV (APA, 1994 ) disorder in a 12-month period (Kessler, Chiu, Demler, & Walters, 2005 ). In the current study we compare scale elevation rates in the MMPI-2-RF normative sample to prevalence rates of mental disorders primarily drawn from the National Comorbidity Study Replication (Kessler et al., 2005 ). Our objective was to evaluate MMPI-2-RF elevation rates in an epidemiological context. Results indicate that MMPI-2-RF scale elevation rates were generally consistent with epidemiological data when examined in the context of standard interpretation guidelines for the inventory. We also reiterate Ben-Porath and Tellegen's (2008/2011) caution that MMPI-2-RF scale elevations alone are not sufficient to indicate the presence of psychiatric disorder. Rather they are best viewed as indications of the need to evaluate the individual for possible disorder(s). Implications of these results, limitations of this study, and future directions in research are discussed.

Brugada-like Precordial ST Elevation on ECG by Anterior Mediastinal Infective Mass Lesion

Directory of Open Access Journals (Sweden)

Yuji Nakazato

2003-07-01

Full Text Available Several causes are known to induce the right precordial ST elevation mimicking Brugada syndrome. Right ventricular outflow area is assumed to be responsible for such ECG changes. We experienced a case of anterior mediastinal infective mass lesion with a Brugada-like ECG. A 52-year-old female, who has pulmonary stenosis and recurrent episodes of right ventricular heart failure, complained of high fever, abdominal discomfort, and edema. On physical examination, jugular vein dilation, hepatomegaly, and facial and leg edema were noted. Leucocytosis was also noted on blood examination. An ECG showed right ventricular hypertrophy, incomplete right bundle branch block pattern and marked ST elevation on precordial leads mimicking Brugada syndrome. Magnetic resonance imaging revealed an abnormal mass shadow located on the anterior mediastinum and compressing the right ventricle (Figure 1A. Trans-thoracic echocardiography also showed the high echogenic mass lesion at the anterior side of right ventricle and the vicinity of pulmonary valve. After treatment with antibiotics, the mass lesion gradually shrunk. Concomitantly, the ST elevation disappeared with improvement of inflammatory markers (Figure 1B. The symptoms suggesting right ventricular failure were also ameliorated. The mechanism of Brugada-like ST elevation in this patient was considered to be compression, by the abnormal infective mass, of the right ventricular outflow tract with/without focal pericardial inflammation.

Examining risk factors for cardiovascular disease among food bank members in Vancouver

Directory of Open Access Journals (Sweden)

A.O. Fowokan

2018-06-01

Full Text Available Food banks provide supplemental food to low-income households, yet little is known about the cardiovascular health of food banks members. This study therefore described cardiovascular disease (CVD risk factors among food bank members and explored associations between food insecurity and CVD risk.Adults ≥18 years (n = 77 from three food bank sites in metro Vancouver, British Columbia completed surveys and physical assessments examining a range of socio-demographic variables and CVD risk factors. A composite measure of myocardial infarction (MI risk called the INTERHEART score was assessed and household food insecurity was measured using the Household Food Security Survey Module. Regression models were used to explore associations between food insecurity and CVD risk measures, including the INTERHEART score.Ninety-seven percent of food bank members reported experiencing food insecurity, 65% were current smokers, 53% reported either chronic or several periods of stress in the past year, 55% reported low physical activity levels and 80% reported consuming fewer than five servings of fruit and vegetables daily. Prevalence of self-reported diabetes and hypertension were 13% and 29% respectively. Fifty-two percent of the sample were at high risk of non-fatal MI. No statistically significant associations were found between increased severity of food insecurity and CVD risk factors among this sample where both severe food insecurity and high CVD risks were prevalent.Food bank members were at elevated risk for CVD compared with the general population. Strategies are needed to reduce prevalence of food insecurity and CVD risk factors, both of which disproportionately affected food bank members. Keywords: Food insecurity, Food banks, Cardiovascular disease, Risk factors, Canada

Effective teamwork in primary healthcare through a structured patient-sorting system - a qualitative study on staff members' conceptions.

Science.gov (United States)

Maun, Andy; Engström, Miriam; Frantz, Anna; Brämberg, Elisabeth Björk; Thorn, Jörgen

2014-11-28

Primary healthcare meets increased demands from an aging population concerning quality and availability while concurrently dealing with a growing shortage of general practitioners and imperfect efficiency in healthcare processes. Reorganization and team development can improve quality and performance but projects in primary care frequently do not attain the targeted results. By developing and introducing a structured patient-sorting system a primary healthcare centre in Western Sweden increased its access rate significantly and employed its medical professionals more efficiently. The aim of this study was to explore staff members' conceptions of the structured patient-sorting system in order to gain an inside perspective on this project. In this qualitative study 16 interviews were conducted over a period of two years and data was analysed using a phenomenographic approach to identify the various conceptions of the eleven participants. Three categories of description were identified: The system was conceptualized as 1) a framework for the development of patient-centred processes that were clear and consistent, 2) a promotor of professional development and a shared ideal of cooperative practice and 3) a common denominator and catalyst in conflict management. This study demonstrates that the introduction of a structured patient-sorting system makes it possible for several important change processes to take place concurrently: improvement of healthcare processes, empowerment of professionals and team development. It therefore indicates the importance of an appropriate, contextualized framework to support multiple concomitant quality improvement processes. Knowledge from this study can be used to assist and improve future implementations in primary healthcare centres.

Family members' expectations regarding nurses' competence in care homes: a qualitative interview study.

Science.gov (United States)

Kiljunen, Outi; Kankkunen, Päivi; Partanen, Pirjo; Välimäki, Tarja

2017-11-22

Structural and cultural changes in the care of older people have influenced nursing practice, creating a need to identify current competency requirements for nurses working in care homes. Family members have an important role in ensuring the well-being of older people living in care homes, and family members' can provide valuable information about competence requirements. To explore the expectations of the care home residents' family members regarding the competence of nurses in care homes for older people. A qualitative descriptive design was used. Semi-structured interviews were conducted with 18 care home residents' family members between March and September 2016. Participants were recruited with help from regional associations and member associations of The Central Association of Carers in Finland and from regional associations of The Alzheimer's Society of Finland. The snowball technique was also used. The data were analysed using inductive content analysis. Ethics committee approval was obtained from the university committee on research ethics, and written informed consent was obtained from participants. The care home residents' family members expected that nurses would be able to interact with and treat people respectfully. Reflective collaboration between the nurse and a family member was also emphasised. Family members expected nurses to provide high-quality basic care and nursing and support residents' well-being individually and holistically. Family members' expectations reflect the need for ethical and interactional competence in the care home. In addition, evidence-based practice competencies are required to provide high-quality care. Nurses' ability to provide person-centred, individual and holistic care is vital to ensure care home residents' well-being. © 2017 Nordic College of Caring Science.

The members of the Agency

International Nuclear Information System (INIS)

1994-01-01

The new members since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.42) are: Armenia, Coratia, the Czech Republic, Lithuania, the Marshall Islands, the Slovak Republic and Uzbekistan. The Attachment to the circular shows the dates on which the 120 States became members of the Agency, as well as those States whose application for membership of the Agency was approved by the General Conference, but who have not yet deposited an instrument of acceptance of the Statute

The members of the Agency

International Nuclear Information System (INIS)

1998-01-01

The document lists the 127 Member States of the Agency as of 1 January 1998. The new Members since the last issue of of the list (INFCIRC/2/49) are Malta and the Republic of Moldova. In an attachment are given the dates on which the present 127 states become Members, the state (Burkina Faso) whose application for membership of the Agency has been approved by the General Conference but which has not deposited an instrument of acceptance of the Statute

The members of the Agency

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-01-15

The document lists the 127 Member States of the Agency as of 1 January 1998. The new Members since the last issue of of the list (INFCIRC/2/49) are Malta and the Republic of Moldova. In an attachment are given the dates on which the present 127 states become Members, the state (Burkina Faso) whose application for membership of the Agency has been approved by the General Conference but which has not deposited an instrument of acceptance of the Statute.

Assessing uncertainty in SRTM elevations for global flood modelling

Science.gov (United States)

Hawker, L. P.; Rougier, J.; Neal, J. C.; Bates, P. D.

2017-12-01

The SRTM DEM is widely used as the topography input to flood models in data-sparse locations. Understanding spatial error in the SRTM product is crucial in constraining uncertainty about elevations and assessing the impact of these upon flood prediction. Assessment of SRTM error was carried out by Rodriguez et al (2006), but this did not explicitly quantify the spatial structure of vertical errors in the DEM, and nor did it distinguish between errors over different types of landscape. As a result, there is a lack of information about spatial structure of vertical errors of the SRTM in the landscape that matters most to flood models - the floodplain. Therefore, this study attempts this task by comparing SRTM, an error corrected SRTM product (The MERIT DEM of Yamazaki et al., 2017) and near truth LIDAR elevations for 3 deltaic floodplains (Mississippi, Po, Wax Lake) and a large lowland region (the Fens, UK). Using the error covariance function, calculated by comparing SRTM elevations to the near truth LIDAR, perturbations of the 90m SRTM DEM were generated, producing a catalogue of plausible DEMs. This allows modellers to simulate a suite of plausible DEMs at any aggregated block size above native SRTM resolution. Finally, the generated DEM's were input into a hydrodynamic model of the Mekong Delta, built using the LISFLOOD-FP hydrodynamic model, to assess how DEM error affects the hydrodynamics and inundation extent across the domain. The end product of this is an inundation map with the probability of each pixel being flooded based on the catalogue of DEMs. In a world of increasing computer power, but a lack of detailed datasets, this powerful approach can be used throughout natural hazard modelling to understand how errors in the SRTM DEM can impact the hazard assessment.

Experiment and calculation of reinforced concrete at elevated temperatures

CERN Document Server

Guo, Zhenhai

2011-01-01

Concrete as a construction material goes through both physical and chemical changes under extreme elevated temperatures. As one of the most widely used building materials, it is important that both engineers and architects are able to understand and predict its behavior in under extreme heat conditions. Brief and readable, this book provides the tools and techniques to properly analysis the effects of high temperature of reinforced concrete which will lead to more stable, safer structures. Based on years of the author's research, Reinforced Concrete at Elevated Temperatures four par

Improvements in or relating to cellular grid structures

International Nuclear Information System (INIS)

Jolly, R.

1979-01-01

In cellular grid structures for positioning an array of nuclear fuel rods by locating them individually in a ferrule joined to its neighbours to form the grid structure, the ferrules are formed in pairs from tubular members each deformed to provide a waist. A bridge piece extends across the waist to divide the tubular member into two cells and it may incorporate a resilient member which projects into the two cells to urge fuel rods in the cells towards co-planar dimples formed in the tubular member opposite the resilient member. (author)

Structure and Evolution of the Lunar Procellarum Region as Revealed by GRAIL Gravity Data

Science.gov (United States)

Andrews-Hanna, Jeffrey C.; Besserer, Jonathan; Head, James W., III; Howett, Carly J. A.; Kiefer, Walter S.; Lucey, Paul J.; McGovern, Patrick J.; Melosh, H. Jay; Neumann, Gregory A.; Phillips, Roger J.;

Global multi-resolution terrain elevation data 2010 (GMTED2010)

Science.gov (United States)

Danielson, Jeffrey J.; Gesch, Dean B.

2011-01-01

In 1996, the U.S. Geological Survey (USGS) developed a global topographic elevation model designated as GTOPO30 at a horizontal resolution of 30 arc-seconds for the entire Earth. Because no single source of topographic information covered the entire land surface, GTOPO30 was derived from eight raster and vector sources that included a substantial amount of U.S. Defense Mapping Agency data. The quality of the elevation data in GTOPO30 varies widely; there are no spatially-referenced metadata, and the major topographic features such as ridgelines and valleys are not well represented. Despite its coarse resolution and limited attributes, GTOPO30 has been widely used for a variety of hydrological, climatological, and geomorphological applications as well as military applications, where a regional, continental, or global scale topographic model is required. These applications have ranged from delineating drainage networks and watersheds to using digital elevation data for the extraction of topographic structure and three-dimensional (3D) visualization exercises (Jenson and Domingue, 1988; Verdin and Greenlee, 1996; Lehner and others, 2008). Many of the fundamental geophysical processes active at the Earth's surface are controlled or strongly influenced by topography, thus the critical need for high-quality terrain data (Gesch, 1994). U.S. Department of Defense requirements for mission planning, geographic registration of remotely sensed imagery, terrain visualization, and map production are similarly dependent on global topographic data. Since the time GTOPO30 was completed, the availability of higher-quality elevation data over large geographic areas has improved markedly. New data sources include global Digital Terrain Elevation Data (DTEDRegistered) from the Shuttle Radar Topography Mission (SRTM), Canadian elevation data, and data from the Ice, Cloud, and land Elevation Satellite (ICESat). Given the widespread use of GTOPO30 and the equivalent 30-arc

A study on Factors Affecting Application of Information and Communication Technology (ICT by Faculty Members of

Directory of Open Access Journals (Sweden)

Elham Biglari

2010-12-01

Full Text Available This paper is an attempt to investigate the factors affecting on ICT application by faculty members of University of Razi. A descriptive-correlative research survey method was used. The statistical population of this research consist of faculty members of University of Kermanshah (N=271. Sampling method was stratified randomization (n=116. Questionnaire was used for data collection, the validity of which was confirmed by the opinions of some of professionals and faculty members of Agriculture Education and Extension and for determining reliability Cronbach's Alpha (0.83 was used. The collected data were analyzed using SPSS software. The findings reveal that there’s a significant positive relationship between the number of published papers in internal and external journals and conferences, familiarity with internet services, skill in driving computer, skill in using internet services, using internet for meeting educational and research needs, skill in English language, attitude towards using ICT in education and research, scientific rank and use of internet for supervising over  thesis and dissertation, on the one hand, and the variable of application of ICT by faculty members of University of Kermanshah. In regression analysis, the predicting variables of factors affecting on application of ICT by faculty members, including skill in using internet services, attitude towards using ICT in research and education and the number of published papers in foreign journals and conferences were entered in 3 stages, which in total explain 25.1 percent variance of dependent variable. 

De stille elever

DEFF Research Database (Denmark)

Winther-Lindqvist, Ditte Alexandra

2012-01-01

Det er blevet en afgørende samværskompetence i uddannelsessystemet at stå aktivt frem og deltage verbalt i skoleklassens liv både fagligt og socialt. Men ikke alle elever deltager lige villigt verbalt i plenum. Artiklen handler om de stille elever og konsekvenserne af stillehed i skolen. Det...... foreslås at skolesystemet sanktionerer ældre elever hårdere for stillehed end yngre elever og det forklares med at skolelivet også er en kultivering henimod elevhed som social identitet og denne er der forventning om at eleverne mestrer i udskolingen....

The influence of the gait-related arm swing on elevation gain measured by sport watches

Directory of Open Access Journals (Sweden)

Ammann Rahel

2016-06-01

Full Text Available The elevation gain is an important contributor to the total workload in endurance sports. The purpose of this study was to evaluate the influence of the arm swing on elevation gain in three sport watches (Garmin® Forerunner 910XT, Polar® RS800CX and Suunto® Ambit2 on a flat 400 m outdoor track. Altogether, a total of 120 repetitions of 1,200 m were performed at self-selected speeds corresponding to strolling, walking, jogging and running. During the assessment two devices of each sport watch, one secured on the hip and one on the wrist, were worn by the participants. A small but significant (effect size = .39; p < .001 influence of the arm swing on elevation was revealed in all sport watches. Elevation indication errors recorded on the wrist were significantly larger than the ones recorded on the hip (4.0-7.4 vs. 1.2-5.7 m per 1,200 m; p < .05. Furthermore, when wearing the devices on the wrist, errors in elevation indication increased when gait speed increased. Users should be aware that wearing the devices on the hip can significantly decrease measurement errors. This might be especially relevant for activities with high dynamics, such as jogging and running.

Structure of the d-alanylgriseoluteic acid biosynthetic protein EhpF, an atypical member of the ANL superfamily of adenylating enzymes

International Nuclear Information System (INIS)

Bera, Asim K.; Atanasova, Vesna; Gamage, Swarna; Robinson, Howard; Parsons, James F.

2010-01-01

The structure of EhpF from P. agglomerans has been solved alone and in complex with phenazine-1,6-dicarboxylate. Apo EhpF was solved and refined in two different space groups at 1.95 and 2.3 Å resolution and the EhpF–phenazine-1,6-dicarboxylate complex structure was determined at 2.8 Å resolution. The structure of EhpF, a 41 kDa protein that functions in the biosynthetic pathway leading to the broad-spectrum antimicrobial compound d-alanylgriseoluteic acid (AGA), is reported. A cluster of approximately 16 genes, including ehpF, located on a 200 kbp plasmid native to certain strains of Pantoea agglomerans encodes the proteins that are required for the conversion of chorismic acid to AGA. Phenazine-1,6-dicarboxylate has been identified as an intermediate in AGA biosynthesis and deletion of ehpF results in accumulation of this compound in vivo. The crystallographic data presented here reveal that EhpF is an atypical member of the acyl-CoA synthase or ANL superfamily of adenylating enzymes. These enzymes typically catalyze two-step reactions involving adenylation of a carboxylate substrate followed by transfer of the substrate from AMP to coenzyme A or another phosphopantetheine. EhpF is distinguished by the absence of the C-terminal domain that is characteristic of enzymes from this family and is involved in phosphopantetheine binding and in the second half of the canonical two-step reaction that is typically observed. Based on the structure of EhpF and a bioinformatic analysis, it is proposed that EhpF and EhpG convert phenazine-1,6-dicarboxylate to 6-formylphenazine-1-carboxylate via an adenylyl intermediate

Priorities in national space strategies and governance of the member states of the European Space Agency

Science.gov (United States)

Adriaensen, Maarten; Giannopapa, Christina; Sagath, Daniel; Papastefanou, Anastasia

2015-12-01

The European Space Agency (ESA) has twenty Member States with a variety of strategic priorities and governance structures regarding their space activities. A number of countries engage in space activities exclusively though ESA, while others have also their own national space programme. Some consider ESA as their prime space agency and others have additionally their own national agency with respective programmes. The main objective of this paper is to provide an up-to date overview and a holistic assessment of strategic priorities and the national space governance structures in 20 ESA Member States. This analysis and assessment has been conducted by analysing the Member States public documents, information provided at ESA workshop on this topic and though unstructured interviews. The paper is structured to include two main elements: priorities and trends in national space strategies and space governance in ESA Member States. The first part of this paper focuses on the content and analysis of the national space strategies and indicates the main priorities and trends in Member States. The priorities are categorised with regards to technology domains, the role of space in the areas of sustainability and the motivators that boost engagement in space. These vary from one Member State to another and include with different levels of engagement in technology domains amongst others: science and exploration, navigation, Earth observation, human space flight, launchers, telecommunications, and integrated applications. Member States allocate a different role of space as enabling tool adding to the advancement of sustainability areas including: security, resources, environment and climate change, transport and communication, energy, and knowledge and education. The motivators motivating reasoning which enhances or hinders space engagement also differs. The motivators identified are industrial competitiveness, job creation, technology development and transfer, social benefits

45 CFR 703.9 - Reimbursement of members.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 3 2010-10-01 2010-10-01 false Reimbursement of members. 703.9 Section 703.9... AND FUNCTIONS OF STATE ADVISORY COMMITTEES § 703.9 Reimbursement of members. (a) Advisory Committee members may be reimbursed by the Commission by a per diem subsistence allowance and for travel expenses at...

Creep Behavior of High-Strength Concrete Subjected to Elevated Temperatures

OpenAIRE

Minho Yoon; Gyuyong Kim; Youngsun Kim; Taegyu Lee; Gyeongcheol Choe; Euichul Hwang; Jeongsoo Nam

2017-01-01

Strain is generated in concrete subjected to elevated temperatures owing to the influence of factors such as thermal expansion and design load. Such strains resulting from elevated temperatures and load can significantly influence the stability of a structure during and after a fire. In addition, the lower the water-to-binder (W?B) ratio and the smaller the quantity of aggregates in high-strength concrete, the more likely it is for unstable strain to occur. Hence, in this study, the compressi...

The surface elevation table and marker horizon technique: A protocol for monitoring wetland elevation dynamics

Science.gov (United States)

James C. Lynch,; Phillippe Hensel,; Cahoon, Donald R.

2015-01-01

The National Park Service, in response to the growing evidence and awareness of the effects of climate change on federal lands, determined that monitoring wetland elevation change is a top priority in North Atlantic Coastal parks (Stevens et al, 2010). As a result, the NPS Northeast Coastal and Barrier Network (NCBN) in collaboration with colleagues from the U.S. Geological Survey (USGS) and The National Oceanic and Atmospheric Administration (NOAA) have developed a protocol for monitoring wetland elevation change and other processes important for determining the viability of wetland communities. Although focused on North Atlantic Coastal parks, this document is applicable to all coastal and inland wetland regions. Wetlands exist within a narrow range of elevation which is influenced by local hydrologic conditions. For coastal wetlands in particular, local hydrologic conditions may be changing as sea levels continue to rise. As sea level rises, coastal wetland systems may respond by building elevation to maintain favorable hydrologic conditions for their survival. This protocol provides the reader with instructions and guidelines on designing a monitoring plan or study to: A) Quantify elevation change in wetlands with the Surface Elevation Table (SET). B) Understand the processes that influence elevation change, including vertical accretion (SET and Marker Horizon methods). C) Survey the wetland surface and SET mark to a common reference datum to allow for comparing sample stations to each other and to local tidal datums. D) Survey the SET mark to monitor its relative stability. This document is divided into two parts; the main body that presents an overview of all aspects of monitoring wetland elevation dynamics, and a collection of Standard Operating Procedures (SOP) that describes in detail how to perform or execute each step of the methodology. Detailed instruction on the installation, data collection, data management and analysis are provided in this report

Evaluation of doctoral nursing programs in Japan by faculty members and their educational and research activities.

Science.gov (United States)

Arimoto, Azusa; Gregg, Misuzu F; Nagata, Satoko; Miki, Yuko; Murashima, Sachiyo

2012-07-01

Evaluation of doctoral programs in nursing is becoming more important with the rapid increase in the programs in Japan. This study aimed to evaluate doctoral nursing programs by faculty members and to analyze the relationship of the evaluation with educational and research activities of faculty members in Japan. Target settings were all 46 doctoral nursing programs. Eighty-five faculty members from 28 programs answered the questionnaire, which included 17 items for program evaluation, 12 items for faculty evaluation, 9 items for resource evaluation, 3 items for overall evaluations, and educational and research activities. A majority gave low evaluations for sources of funding, the number of faculty members and support staff, and administrative systems. Faculty members who financially supported a greater number of students gave a higher evaluation for extramural funding support, publication, provision of diverse learning experiences, time of supervision, and research infrastructure. The more time a faculty member spent on advising doctoral students, the higher were their evaluations on the supportive learning environment, administrative systems, time of supervision, and timely feedback on students' research. The findings of this study indicate a need for improvement in research infrastructure, funding sources, and human resources to achieve quality nursing doctoral education in Japan. Copyright © 2011 Elsevier Ltd. All rights reserved.

Increased serum levels of hyaluronic acid in pregnancies complicated by preeclampsia or hemolysis, elevated liver enzymes, and low platelets syndrome.

Science.gov (United States)

Osmers, R G; Schütz, E; Diedrich, F; Wehry, B; Krauss, T; Oellerich, M; Kuhn, W

1998-02-01

Fifteen percent of patients who later have hemolysis, elevated liver enzymes, and low platelets syndrome develop initially have nonspecific symptoms. Early diagnosis could ensure adequate obstetric management; however, prognostic biochemical tests are lacking. We hypothesized that elevated hyaluronic acid serum levels might be an early indicator of hemolysis, elevated liver enzymes, and low platelets syndrome because it is known to be a sensitive marker of liver cell function. Hyaluronic acid in serum was measured in patients with normal pregnancies (n = 109) and in those patients with pregnancies complicated by preeclampsia (n = 14) or hemolysis, elevated liver enzymes, and low platelets syndrome (n = 11). A significant increase in hyaluronic acid serum concentrations was observed in patients with hemolysis, elevated liver enzymes, and low platelets syndrome or with preeclampsia (p hyaluronic acid serum levels in hemolysis, elevated liver enzymes, and low platelets syndrome correlated with the clinical severity of the individual course of disease as measured by intensive care unit time (r = 0.72; p hyaluronic acid in preeclampsia and hemolysis, elevated liver enzymes, and low platelets syndrome are significantly elevated and might play an important diagnostic and prognostic role in patients with hemolysis, elevated liver enzymes, and low platelets syndrome.

Simulation of spring wheat responses to elevated CO2 and temperature by using CERES-wheat crop model

Directory of Open Access Journals (Sweden)

H. LAURILA

2008-12-01

Full Text Available The CERES-wheat crop simulation model was used to estimate the changes in phenological development and yield production of spring wheat (Triticum aestivum L., cv. Polkka under different temperature and CO2 growing conditions. The effects of elevated temperature (3-4°C and CO2 concentration (700 ppm as expected for Finland in 2100 were simulated. The model was calibrated for long-day growing conditions in Finland. The CERES-wheat genetic coefficients for cv. Polkka were calibrated by using the MTT Agrifood Research Finland (MTT official variety trial data (1985-1990. Crop phenological development and yield measurements from open-top chamber experiments with ambient and elevated temperature and CO2 treatments were used to validate the model. Simulated mean grain yield under ambient temperature and CO2 conditions was 6.16 t ha-1 for potential growth (4.49 t ha-1 non-potential and 5.47 t ha-1 for the observed average yield (1992-1994 in ambient open-top chamber conditions. The simulated potential grain yield increased under elevated CO2 (700 ppm to 142% (167% non-potential from the simulated reference yield (100%, ambient temperature and CO2 350 ppm. Simulations for current sowing date and elevated temperature (3°C indicate accelerated anthesis and full maturity. According to the model estimations, potential yield decreased on average to 80.4% (76.8% non-potential due to temperature increase from the simulated reference. When modelling the concurrent elevated temperature and CO2 interaction, the increase in grain yield due to elevated CO2 was reduced by the elevated temperature. The combined CO2 and temperature effect increased the grain yield to 106% for potential growth (122% non-potential compared to the reference. Simulating the effects of earlier sowing, the potential grain yield increased under elevated temperature and CO2 conditions to 178% (15 days earlier sowing from 15 May, 700 ppm CO2, 3°C from the reference. Simulation results suggest

FMEA team performance in health care: A qualitative analysis of team member perceptions.

Science.gov (United States)

Wetterneck, Tosha B; Hundt, Ann Schoofs; Carayon, Pascale

2009-06-01

: Failure mode and effects analysis (FMEA) is a commonly used prospective risk assessment approach in health care. Failure mode and effects analyses are time consuming and resource intensive, and team performance is crucial for FMEA success. We evaluate FMEA team members' perceptions of FMEA team performance to provide recommendations to improve the FMEA process in health care organizations. : Structured interviews and survey questionnaires were administered to team members of 2 FMEA teams at a Midwest Hospital to evaluate team member perceptions of FMEA team performance and factors influencing team performance. Interview transcripts underwent content analysis, and descriptive statistics were performed on questionnaire results to identify and quantify FMEA team performance. Theme-based nodes were categorized using the input-process-outcome model for team performance. : Twenty-eight interviews and questionnaires were completed by 24 team members. Four persons participated on both teams. There were significant differences between the 2 teams regarding perceptions of team functioning and overall team effectiveness that are explained by difference in team inputs and process (e.g., leadership/facilitation, team objectives, attendance of process owners). : Evaluation of team members' perceptions of team functioning produced useful insights that can be used to model future team functioning. Guidelines for FMEA team success are provided.

The Members of the Agency

International Nuclear Information System (INIS)

1994-01-01

The new members since the last list of Member States of the Agency was issued (INFCIRC/2/Rev.43) are: Kazakhstan and the former Yugoslav Republic of Macedonia. The Democratic People's Republic of Korea withdrew from membership of the Agency as of 13 June 1994. The Attachment hereto shows the dates on which the 121 States became members of the Agency, as well as those States whose application for membership of the Agency was approved by the General Conference, but who have not yet deposited an instrument of acceptance of the Statute

Dynamic multibody modeling for tethered space elevators

Science.gov (United States)

Williams, Paul

2009-08-01

This paper presents a fundamental modeling strategy for dealing with powered and propelled bodies moving along space tethers. The tether is divided into a large number of discrete masses, which are connected by viscoelastic springs. The tether is subject to the full range of forces expected in Earth orbit in a relatively simple manner. Two different models of the elevator dynamics are presented. In order to capture the effect of the elevator moving along the tether, the elevator dynamics are included as a separate body in both models. One model treats the elevator's motion dynamically, where propulsive and friction forces are applied to the elevator body. The second model treats the elevator's motion kinematically, where the distance along the tether is determined by adjusting the lengths of tether on either side of the elevator. The tether model is used to determine optimal configurations for the space elevator. A modal analysis of two different configurations is presented which show that the fundamental mode of oscillation is a pendular one around the anchor point with a period on the order of 160 h for the in-plane motion, and 24 h for the out-of-plane motion. Numerical simulation results of the effects of the elevator moving along the cable are presented for different travel velocities and different elevator masses.

Tensor-based morphometry of cannabis use on brain structure in individuals at elevated genetic risk of schizophrenia.

Science.gov (United States)

Welch, K A; Moorhead, T W; McIntosh, A M; Owens, D G C; Johnstone, E C; Lawrie, S M

2013-10-01

Schizophrenia is associated with various brain structural abnormalities, including reduced volume of the hippocampi, prefrontal lobes and thalami. Cannabis use increases the risk of schizophrenia but reports of brain structural abnormalities in the cannabis-using population have not been consistent. We used automated image analysis to compare brain structural changes over time in people at elevated risk of schizophrenia for familial reasons who did and did not use cannabis. Magnetic resonance imaging (MRI) scans were obtained from subjects at high familial risk of schizophrenia at entry to the Edinburgh High Risk Study (EHRS) and approximately 2 years later. Differential grey matter (GM) loss in those exposed (n=23) and not exposed to cannabis (n=32) in the intervening period was compared using tensor-based morphometry (TBM). Cannabis exposure was associated with significantly greater loss of right anterior hippocampal (pcorrected=0.029, t=3.88) and left superior frontal lobe GM (pcorrected=0.026, t=4.68). The former finding remained significant even after the exclusion of individuals who had used other drugs during the inter-scan interval. Using an automated analysis of longitudinal data, we demonstrate an association between cannabis use and GM loss in currently well people at familial risk of developing schizophrenia. This observation may be important in understanding the link between cannabis exposure and the subsequent development of schizophrenia.

Troponin elevation in subarachnoid hemorrhage

Directory of Open Access Journals (Sweden)

Ioannis N. Mavridis

2015-03-01

Full Text Available Troponin (tr elevation in aneurysmal subarachnoid hemorrhage (SAH patients is often difficult to be appropriately assessed by clinicians, causing even disagreements regarding its management between neurosurgeons and cardiologists. The purpose of this article was to review the literature regarding the clinical interpretation of tr elevation in SAH. We searched for articles in PubMed using the key words: “troponin elevation” and “subarachnoid hemorrhage”. All of them, as well as relative neurosurgical books, were used for this review. Some type of cardiovascular abnormality develops in most SAH patients. Neurogenic stunned myocardium is a frequent SAH complication, due to catecholamine surge which induces cardiac injury, as evidenced by increased serum tr levels, electrocardiographic (ECG changes and cardiac wall motion abnormalities. Tr elevation, usually modest, is an early and specific marker for cardiac involvement after SAH and its levels peak about two days after SAH. Cardiac tr elevation predictors include poor clinical grade, intraventricular hemorrhage, loss of consciousness at ictus, global cerebral edema, female sex, large body surface area, lower systolic blood pressure, higher heart rate and prolonged Q-Tc interval. Elevated tr levels are associated with disability and death (especially tr >1 μg/L, worse neurological grade, systolic and diastolic cardiac dysfunction, pulmonary congestion, longer intensive care unit stay and incidence of vasospasm. Tr elevation is a common finding in SAH patients and constitutes a rightful cause of worry about the patients' cardiac function and prognosis. It should be therefore early detected, carefully monitored and appropriately managed by clinicians.

Fracture mechanical analysis of strengthened concrete tension members with one crack

DEFF Research Database (Denmark)

Hansen, Christian Skodborg; Stang, Henrik

2012-01-01

A concrete tension member strengthened 2 with fiber reinforced polymer plates on two sides 3 is analyzed with non-linear fracture mechanics. The 4 analysis of the strengthened tension member incorpo5 rates cohesive properties for both concrete and inter6 face between concrete and strengthening...... the structural classification parameters, is inves13 tigated in a non-dimensional analysis, and found to 14 depend strongly on the ratio between interfacial and 15 concrete fracture energies....

Natural frequencies of the frames having curved member

International Nuclear Information System (INIS)

Tekelioglu, M.; Ozyigit, H.A.; Ridvan, H.

2001-01-01

In-plane and out-of-plane vibrations of a frame having a curved member are studied. Although the analysis is carried out on a frame having a straight and a curve beam, it can be applicable for all the frame type structures. Different end conditions are considered for the system. Rotary inertia and extensional effects are included for the curved member. Finite element method is used as analysis tool. Natural frequencies of the curved beams for different end conditions are calculated first, and then the frequencies of the frames are investigated. The transformation from local coordinates to global coordinates for curved beams needs special attention in the analysis. The results are compared with other methods. (author)

Influence of ocean acidification on plankton community structure during a winter-to-summer succession: An imaging approach indicates that copepods can benefit from elevated CO2 via indirect food web effects

Science.gov (United States)

Taucher, Jan; Haunost, Mathias; Boxhammer, Tim; Bach, Lennart T.; Algueró-Muñiz, María; Riebesell, Ulf

2017-01-01

Plankton communities play a key role in the marine food web and are expected to be highly sensitive to ongoing environmental change. Oceanic uptake of anthropogenic carbon dioxide (CO2) causes pronounced shifts in marine carbonate chemistry and a decrease in seawater pH. These changes–summarized by the term ocean acidification (OA)–can significantly affect the physiology of planktonic organisms. However, studies on the response of entire plankton communities to OA, which also include indirect effects via food-web interactions, are still relatively rare. Thus, it is presently unclear how OA could affect the functioning of entire ecosystems and biogeochemical element cycles. In this study, we report from a long-term in situ mesocosm experiment, where we investigated the response of natural plankton communities in temperate waters (Gullmarfjord, Sweden) to elevated CO2 concentrations and OA as expected for the end of the century (~760 μatm pCO2). Based on a plankton-imaging approach, we examined size structure, community composition and food web characteristics of the whole plankton assemblage, ranging from picoplankton to mesozooplankton, during an entire winter-to-summer succession. The plankton imaging system revealed pronounced temporal changes in the size structure of the copepod community over the course of the plankton bloom. The observed shift towards smaller individuals resulted in an overall decrease of copepod biomass by 25%, despite increasing numerical abundances. Furthermore, we observed distinct effects of elevated CO2 on biomass and size structure of the entire plankton community. Notably, the biomass of copepods, dominated by Pseudocalanus acuspes, displayed a tendency towards elevated biomass by up to 30–40% under simulated ocean acidification. This effect was significant for certain copepod size classes and was most likely driven by CO2-stimulated responses of primary producers and a complex interplay of trophic interactions that allowed this

Screening of a healthy newborn identifies three adult family members with symptomatic glutaric aciduria type I

Directory of Open Access Journals (Sweden)

MCH Janssen

2014-06-01

Full Text Available We report three adult sibs (one female, two males with symptomatic glutaric acidura type I, who were diagnosed after a low carnitine level was found by newborn screening in a healthy newborn of the women. All three adults had low plasma carnitine, elevated glutaric acid levels and pronounced 3-hydroxyglutaric aciduria. The diagnosis was confirmed by undetectable glutaryl-CoA dehydrogenase activity in lymphocytes and two pathogenic heterozygous mutations in the GCDH gene (c.1060A>G, c.1154C>T. These results reinforce the notion that abnormal metabolite levels in newborns may lead to the diagnosis of adult metabolic disease in the mother and potentially other family members.

Implications of discontinuous elevation gradients on fragmentation and restoration in patterned wetlands

Science.gov (United States)

Zweig, Christa L.; Reichert, Brian E.; Kitchens, Wiley M.

2011-01-01

Large wetlands around the world face the possibility of degradation, not only from complete conversion, but also from subtle changes in their structure and function. While fragmentation and isolation of wetlands within heterogeneous landscapes has received much attention, the disruption of spatial patterns/processes within large wetland systems and the resulting fragmentation of community components are less well documented. A greater understanding of pattern/process relationships and landscape gradients, and what occurs when they are altered, could help avoid undesirable consequences of restoration actions. The objective of this study is to determine the amount of fragmentation of sawgrass ridges due to artificial impoundment of water and how that may be differentially affected by spatial position relative to north and south levees. We also introduce groundbreaking evidence of landscape-level discontinuous elevation gradients within WCA3AS by comparing generalized linear and generalized additive models. These relatively abrupt breaks in elevation may have non-linear effects on hydrology and vegetation communities and would be crucial in restoration considerations. Modeling suggests there are abrupt breaks in elevation as a function of northing (Y-coordinate). Fragmentation indices indicate that fragmentation is a function of elevation and easting (X-coordinate), and that fragmentation has increased from 1988-2002. When landscapes change and the changes are compounded by non-linear landscape variables that are described herein, the maintenance processes change with them, creating a degraded feedback loop that alters the system's response to structuring variables and diminishes our ability to predict the effects of restoration projects or climate change. Only when these landscape variables and linkages are clearly defined can we predict the response to potential perturbations and apply the knowledge to other landscape-level wetland systems in need of future

Vitamin K 3 family members - Part II: Single crystal X-ray structures, temperature-induced packing polymorphism, magneto-structural correlations and probable anti-oncogenic candidature

Science.gov (United States)

Rane, Sandhya; Ahmed, Khursheed; Salunke-Gawali, Sunita; Zaware, Santosh B.; Srinivas, D.; Gonnade, Rajesh; Bhadbhade, Mohan

2008-12-01

Temperature-induced packing polymorphism is observed for vitamin K 3 (menadione, 3-methyl-1,4-naphthoquinone, 1). Form 1a crystallizes at 300 K and 1b at 277 K both in the same space group P2 1/ c. Form 1b contains one molecule per asymmetric unit, performing anisotropy in g-factor viz. g z = 2.0082, g y = 2.0055 and g x = 2.0025, whereas form 1a contains two molecules in its asymmetric unit. Vitamin K 3 family members 2, [2-hydroxy vitamin K 3] and 3, [2-hydroxy-1-oximino vitamin K 3] also perform intrinsic neutral active naphthosemiquinone valence tautomers even in dark having spin concentrations due to hydrogen bonding and aromatic stacking interactions which are compared to vitamin K 3. The significant lateral C-H⋯O and O-H⋯π bifurcated or π-π ∗ interactions are discussed for molecular associations and radical formations. X-ray structure of 3 revealed π-π ∗ stack dimers as radicals signatured in EPR as triplet with five hyperfine splits [ Ā( 14N) = 11.9 G]. The centrosymmetric biradicals in 3 show diamagnetism at high temperature but below 10 K it shows paramagnetism with μeff as 0.19 B.M. Vitamin K 3 and its family members inhibit biological activities of acid phosphatase ( APase), which are proportional to their spin concentrations. This may relate to their probable anti-oncogenic candidature in future.

Structure of fenchone by broadband rotational spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Loru, Donatella; Bermúdez, Miguel A.; Sanz, M. Eugenia [Department of Chemistry, King’s College London, London SE1 1DB (United Kingdom)

2016-08-21

The bicyclic terpenoid fenchone (C{sub 10}H{sub 16}O, 1,3,3-trimethylbicyclo[2.2.1]heptan-2-one) has been investigated by chirped pulse Fourier transform microwave spectroscopy in the 2-8 GHz frequency region. The parent species and all heavy atom isotopologues have been observed in their natural abundance. The experimental rotational constants of all isotopic species observed have been determined and used to obtain the substitution (r{sub s}) and effective (r{sub 0}) structures of fenchone. Calculations at the B3LYP, M06-2X, and MP2 levels of theory with different basis sets were carried out to check their performance against experimental results. The structure of fenchone has been compared with those of norbornane (bicyclo[2.2.1]heptane) and the norbornane derivatives camphor (1,7,7-trimethylbicyclo[2.2.1]heptan-2-one) and camphene (3,3-dimethyl-2-methylenebicyclo[2.2.1]heptane), both with substituents at C{sub 2}. The structure of fenchone is remarkably similar to those of camphor and camphene. Comparison with camphor allows identification of changes in ∠CCC angles due to the different position of the methyl groups. All norbornane derivatives display similar structural changes with respect to norbornane. These changes mainly affect the bond lengths and angles of the six-membered rings, indicating that the substituent at C{sub 2} drives structural adjustments to minimise ring strain after its introduction.

PARAMETERS AFFECTING THE STRUCTURAL ANALYSIS OF A TUNNEL STRUCTURE EXPOSED TO FIRE

Directory of Open Access Journals (Sweden)

Omid Pouran

2016-12-01

Full Text Available Behaviour of cut-and-cover tunnels exposed to fire should be analysed by using a realistic structural model that takes account of mechanical and thermal effects on the structure. This has been performed with the aid of Finite Element (FE software package called SOFiSTiK in parallel, for two types of elements as a scope of research project financed by the German Bundesanstalt für Straßenwesen BAST. Since the stiffness of the structure at elevated temperatures is highly affected, a realistic model of structural behaviour of the tunnel could be only achieved by considering the nonlinear analysis of the structure. This has been performed for a 2–cell cut and cover tunnel by taking account of simultaneous reduction of stiffness and strength and the time-dependent increasing indirect effects due to axial constraints and temperature gradients induced by elevated temperatures. The thermal analyses have been performed and the effects were implemented into the structural model by the multi-layered strain model. The stress–strain model proposed by EN 1992-1-2 is implemented for the elevated temperature. Since there was sufficient amount of Polypropylene fibres in the concrete mixtures, modelling of spalling was excluded from the analysis. The critical corresponding stresses and material behaviour are compared and interpreted at different time stages. The main parameters affecting the accuracy and convergence of the results of structural analysis for the used model are identified: defining a realistic fire action, using concrete material model fulfilling the requirements of fire situation in tunnels, defining appropriate time intervals for load implementations. These parameters along with other parameters, which influence the results to a lesser degree, are identified and investigated in this paper.