WorldWideScience

Sample records for strongly adsorbed layer

  1. The influence of frequency on fractal dimension of adsorbed layers

    International Nuclear Information System (INIS)

    Gasparovic, B.; Risovic, D.; Cosovic, B.; Nelson, A.

    2007-01-01

    Alternating current (AC) voltammetry and electrochemical impedance spectroscopy are often the methods of choice for use in study of adsorption of organic molecules. The adsorption of organic molecules on interface may result in the formation of fractal structures, whose fractal dimension can be estimated using the method of scaling the hanging mercury drop electrode (HMDE). The aim of present study was to check whether the estimated fractal dimension, D (or for that matter the fractal ordering of the adsorbed layer) shows any correlation (dependence) with change of applied frequency, and second, to check the possibility to extend the method to broad frequency spectrum compatible with impedance spectroscopy. The investigation included two surfactants nonionic Triton-X-100 (T-X-100) and anionic sodium dodecyl sulfate (SDS) and alcohol tert-butanol. All measurements were performed on HMDE at thermodynamic equilibrium employing broad frequency spectrum. The validity of the approach was checked by measurements on pure electrolyte and by comparison with previously obtained results for fractal layers. The results of the investigations show that: (1) the method of scaling the HMDE to obtain the fractal dimension of adsorbed layer is compatible with impedance spectroscopy and the combination of these methods can be used as a powerful tool to investigate fractal aspect of adsorption of organic molecules; (2) fractal ordering of adsorbed layer and the value of fractal dimension is not influenced by the frequency of applied sinusoidal voltage perturbations

  2. Adsorbate-mediated strong metal-support interactions in oxide-supported Rh catalysts.

    Science.gov (United States)

    Matsubu, John C; Zhang, Shuyi; DeRita, Leo; Marinkovic, Nebojsa S; Chen, Jingguang G; Graham, George W; Pan, Xiaoqing; Christopher, Phillip

    2017-02-01

    The optimization of supported metal catalysts predominantly focuses on engineering the metal site, for which physical insights based on extensive theoretical and experimental contributions have enabled the rational design of active sites. Although it is well known that supports can influence the catalytic properties of metals, insights into how metal-support interactions can be exploited to optimize metal active-site properties are lacking. Here we utilize in situ spectroscopy and microscopy to identify and characterize a support effect in oxide-supported heterogeneous Rh catalysts. This effect is characterized by strongly bound adsorbates (HCO x ) on reducible oxide supports (TiO 2 and Nb 2 O 5 ) that induce oxygen-vacancy formation in the support and cause HCO x -functionalized encapsulation of Rh nanoparticles by the support. The encapsulation layer is permeable to reactants, stable under the reaction conditions and strongly influences the catalytic properties of Rh, which enables rational and dynamic tuning of CO 2 -reduction selectivity.

  3. A DFT study of halogen atoms adsorbed on graphene layers

    International Nuclear Information System (INIS)

    Medeiros, Paulo V C; De Brito Mota, F; De Castilho, Caio M C; Mascarenhas, Artur J S

    2010-01-01

    In this work, ab initio density functional theory calculations were performed in order to study the structural and electronic properties of halogens (X = fluorine, chlorine, bromine or iodine) that were deposited on both sides of graphene single layers (X-graphene). The adsorption of these atoms on only one side of the layer with hydrogen atoms adsorbed on the other was also considered (H,X-graphene). The results indicate that the F-C bond in the F-graphene system causes an sp 2 to sp 3 transition of the carbon orbitals, and similar effects seem to occur in the H,X-graphene systems. For the other cases, two configurations are found: bonded (B) and non-bonded (NB). For the B configuration, the structural arrangement of the atoms was similar to F-graphene and H-graphene (graphane), although the electronic structures present some differences. In the NB configuration, the interaction between the adsorbed atoms and the graphene layer seems to be essentially of the van der Waals type. In these cases, the original shape of the graphene layer presents only small deviations from the pristine form and the adsorbed atoms reach equilibrium far from the sheet. The F-graphene structure has a direct bandgap of approximately 3.16 eV at the Γ point, which is a value that is close to the value of 3.50 eV that was found for graphane. The Cl-graphene (B configuration), H,F-graphene and H,Cl-graphene systems have smaller bandgap values. All of the other systems present metallic behaviours. Energy calculations indicate the possible stability of these X-graphene layers, although some considerations about the possibility of spontaneous formation have to be taken into account.

  4. A DFT study of halogen atoms adsorbed on graphene layers.

    Science.gov (United States)

    Medeiros, Paulo V C; Mascarenhas, Artur J S; de Brito Mota, F; de Castilho, Caio M C

    2010-12-03

    In this work, ab initio density functional theory calculations were performed in order to study the structural and electronic properties of halogens (X = fluorine, chlorine, bromine or iodine) that were deposited on both sides of graphene single layers (X-graphene). The adsorption of these atoms on only one side of the layer with hydrogen atoms adsorbed on the other was also considered (H,X-graphene). The results indicate that the F-C bond in the F-graphene system causes an sp(2) to sp(3) transition of the carbon orbitals, and similar effects seem to occur in the H,X-graphene systems. For the other cases, two configurations are found: bonded (B) and non-bonded (NB). For the B configuration, the structural arrangement of the atoms was similar to F-graphene and H-graphene (graphane), although the electronic structures present some differences. In the NB configuration, the interaction between the adsorbed atoms and the graphene layer seems to be essentially of the van der Waals type. In these cases, the original shape of the graphene layer presents only small deviations from the pristine form and the adsorbed atoms reach equilibrium far from the sheet. The F-graphene structure has a direct bandgap of approximately 3.16 eV at the Γ point, which is a value that is close to the value of 3.50 eV that was found for graphane. The Cl-graphene (B configuration), H,F-graphene and H,Cl-graphene systems have smaller bandgap values. All of the other systems present metallic behaviours. Energy calculations indicate the possible stability of these X-graphene layers, although some considerations about the possibility of spontaneous formation have to be taken into account.

  5. Reflectance difference spectroscopy (RDS) investigation of ordering processes and phase transitions in adsorbate layers on Cu(110)

    International Nuclear Information System (INIS)

    Hohage, M.; Sun, L.D.; Zeppenfeld, P.; Balderas, R.; Hingerl, K.

    2002-01-01

    Full text: We present an RDS investigation of the behavior of adsorbate layers on Cu(110). RDS measures the difference in the optical reflectivity at normal incidence for light polarized in two orthogonal directions. In the case of fcc crystals like Cu the isotropic bulk has no contribution to the signal. Only symmetry breaking surfaces generate an optical anisotropy and thus a RDS response. The anisotropy signal of Cu(110) is strongly altered by the adsorption of molecules like oxygen and CO. The RDS signal depends not only on the species and coverage of the adsorbate, but is also extremely sensitive to the arrangement of the molecules within the layer. Disorder-order transitions and transformations between different superstructures and reconstructions are monitored in dependence of coverage and temperature. STM and diffraction techniques are used as complementary methods to further characterize the sample. It is shown that RDS is, indeed, an extremely sensitive method to study coverage or temperature driven structural changes of adsorbate layers as well as of adsorbate induced changes of the substrate surface. In the case of CO adsorption structural changes occur within the CO layer by forming different superstructures. The different CO structures induce strain and stress within the Cu surface and thus cause specific modifications of the electronic structure of the Cu. Oxygen adsorption, however, results in a more direct change in the Cu surface structure by the creation of vacancy clusters and CuO islands. (author)

  6. Strong ground motion spectra for layered media

    International Nuclear Information System (INIS)

    Askar, A.; Cakmak, A.S.; Engin, H.

    1977-01-01

    This article presents an analytic method and calculations of strong motion spectra for the energy, displacement, velocity and acceleration based on the physical and geometric ground properties at a site. Although earthquakes occur with large deformations and high stress intensities which necessarily lead to nonlinear phenomena, most analytical efforts to date have been based on linear analyses in engineering seismology and soil dynamics. There are, however, a wealth of problems such as the shifts in frequency, dispersion due to the amplitude, the generation of harmonics, removal of resonance infinities, which cannot be accounted for by a linear theory. In the study, the stress-strain law for soil is taken as tau=G 0 γ+G 1 γ 3 +etaγ where tau is the stress, γ is the strain, G 0 and G 1 are the elasticity coefficients and eta is the damping and are different in each layer. The above stress-strain law describes soils with hysterisis where the hysterisis loops for various amplitudes of the strain are no longer concentric ellipses as for linear relations but are oval shapes rotated with respect to each other similar to the materials with the Osgood-Ramberg law. It is observed that even slight nonlinearities may drastically alter the various response spectra from that given by linear analysis. In fact, primary waves cause resonance conditions such that secondary waves are generated. As a result, a weak energy transfer from the primary to the secondary waves takes place, thus altering the wave spectrum. The mathematical technique that is utilized for the solution of the nonlinear equation is a special perturbation method as an extension of Poincare's procedure. The method considers shifts in the frequencies which are determined by the boundedness of the energy

  7. Hydrodynamic thickness of petroleum oil adsorbed layers in the pores of reservoir rocks.

    Science.gov (United States)

    Alkafeef, Saad F; Algharaib, Meshal K; Alajmi, Abdullah F

    2006-06-01

    The hydrodynamic thickness delta of adsorbed petroleum (crude) oil layers into the pores of sandstone rocks, through which the liquid flows, has been studied by Poiseuille's flow law and the evolution of (electrical) streaming current. The adsorption of petroleum oil is accompanied by a numerical reduction in the (negative) surface potential of the pore walls, eventually stabilizing at a small positive potential, attributed to the oil macromolecules themselves. After increasing to around 30% of the pore radius, the adsorbed layer thickness delta stopped growing either with time or with concentrations of asphaltene in the flowing liquid. The adsorption thickness is confirmed with the blockage value of the rock pores' area determined by the combination of streaming current and streaming potential measurements. This behavior is attributed to the effect on the disjoining pressure across the adsorbed layer, as described by Derjaguin and Churaev, of which the polymolecular adsorption films lose their stability long before their thickness has approached the radius of the rock pore.

  8. A machine learning approach to graph-theoretical cluster expansions of the energy of adsorbate layers

    Science.gov (United States)

    Vignola, Emanuele; Steinmann, Stephan N.; Vandegehuchte, Bart D.; Curulla, Daniel; Stamatakis, Michail; Sautet, Philippe

    2017-08-01

    The accurate description of the energy of adsorbate layers is crucial for the understanding of chemistry at interfaces. For heterogeneous catalysis, not only the interaction of the adsorbate with the surface but also the adsorbate-adsorbate lateral interactions significantly affect the activation energies of reactions. Modeling the interactions of the adsorbates with the catalyst surface and with each other can be efficiently achieved in the cluster expansion Hamiltonian formalism, which has recently been implemented in a graph-theoretical kinetic Monte Carlo (kMC) scheme to describe multi-dentate species. Automating the development of the cluster expansion Hamiltonians for catalytic systems is challenging and requires the mapping of adsorbate configurations for extended adsorbates onto a graphical lattice. The current work adopts machine learning methods to reach this goal. Clusters are automatically detected based on formalized, but intuitive chemical concepts. The corresponding energy coefficients for the cluster expansion are calculated by an inversion scheme. The potential of this method is demonstrated for the example of ethylene adsorption on Pd(111), for which we propose several expansions, depending on the graphical lattice. It turns out that for this system, the best description is obtained as a combination of single molecule patterns and a few coupling terms accounting for lateral interactions.

  9. Stability, structural and electronic properties of benzene molecule adsorbed on free standing Au layer

    Energy Technology Data Exchange (ETDEWEB)

    Katoch, Neha, E-mail: nehakatoch2@gmail.com; Kapoor, Pooja; Sharma, Munish; Ahluwalia, P. K. [Physics Department, Himachal Pradesh University, Shimla, Himachal Pradesh, India 171005 (India); Kumar, Ashok [Center for Physical Sciences, School of Basic and Applied Sciences, Central University of Punjab, Bathinda, India, 151001 (India)

    2016-05-23

    We report stability and electronic properties of benzene molecule adsorbed on the Au atomic layer within the framework of density function theory (DFT). Horizontal configuration of benzene on the top site of Au monolayer prefers energetically over other studied configurations. On the adsorption of benzene, the ballistic conductance of Au monolayer is found to decrease from 4G{sub 0} to 2G{sub 0} suggesting its applications for the fabrications of organic sensor devices based on the Au atomic layers.

  10. Adsorbed layers on (111)InAs faces in contact with In-As-Cl-H gas phase, and the possibility of phase transitions in the adsorbed layers

    Science.gov (United States)

    Chernov, A. A.; Ruzaikin, M. P.

    1981-04-01

    Adsorption of various species existing in the In-As-Cl-H CVD gaseous system on both InAs (111) faces is considered. Arsenic is supposed to be adsorbed in the form of triangles As 3 and tetrahedrons As 4, each of them occupying 3 atomic sites above In or As atoms on (111)In or (111)As, respectively. The system of polyatomic adsorption equations was used to find the coverages of the faces by various species. Admolecule-surface bond strengths are taken to be equal to the ones for the single bonds in molecules. Pauling electronegativities were used to find the effective charges of the atoms in the adsorption layer. Thus, the dipole moments of adsorbed molecules which arise are directed along the In-As bonds in the InAs lattice. With this geometry, the calculated electrostatic dipole-dipole attraction between InCl molecules forming a dense layer on (111)As exceeds 12 kcal/mol. Thus, condensation of the two-dimensional gas of adsorbed InCl molecules should be expected. Corresponding S-shape isotherms θ( P) are calculated for different As 3 vapor pressures, θ and P being the surface coverage and bulk vapor pressure of InCl. Intervals of {InCl 3}/{H 2} ratios at different temperatures where the two-dimensional condensation may occur, are presented for realistic CVD conditions. Two-dimensional condensation may result in sharp changes in kinetic coefficient and thus in autho-oscillations in growth rate and doping level creating periodic superstructures. Nucleation and CVD growth processes are discussed.

  11. Influence of carboxylic ion-pairing reagents on retention of peptides in thin-layer chromatography systems with C18 silica-based adsorbents.

    Science.gov (United States)

    Gwarda, Radosław Ł; Aletańska-Kozak, Monika; Klimek-Turek, Anna; Ziajko-Jankowska, Agnieszka; Matosiuk, Dariusz; Dzido, Tadeusz H

    2016-04-01

    One of the main problems related to chromatography of peptides concerns adverse interactions of their strong basic groups with free silanol groups of the silica based stationary phase. Influence of type and concentration of ion-pairing regents on peptide retention in reversed-phase high-performance liquid chromatography (RP-HPLC) systems has been discussed before. Here we present influence of these mobile phase additives on retention of some peptide standards in high-performance thin-layer chromatography (HPTLC) systems with C18 silica-based adsorbents. We prove, that due to different characteristic of adsorbents used in both techniques (RP HPLC and HPTLC), influence of ion-pairing reagents on retention of basic and/or amphoteric compounds also may be quite different. C18 silica-based HPTLC adsorbents provide more complex mechanism of retention and should be rather considered as mixed-mode adsorbents. Copyright © 2016 Elsevier B.V. All rights reserved.

  12. Evaluation of migration of cesium-137 adsorbed on fine soil particles through natural aerated soil layer

    International Nuclear Information System (INIS)

    Ogawa, Hiromichi; Takebe, Shinichi; Yamamoto, Tadatoshi

    1991-01-01

    In order to evaluate migration of 137 Cs adsorbed on fine soil particles in natural aerated soil layers, filtration constants of fine soil particles between soil and pore water were determined by the inverse analysis of the results of a large scale indoor migration test (STEM) using the soil layer samples collected from the natural aerated soil layers of Tokai and Rokkasho-mura without any disturbance. The amounts of 137 Cs which migrated through the soil layer samples with the movement of fine soil particles were also determined by the inverse analysis. The filtration constant for a loamy soil layer was larger than that for a sandy soil layer and the dependence of the filtration constant on mean diameter was the same as that obtained in small scale column experiments. On the other hand, the amount of 137 Cs which migrated through the soil layer sample with the movement of fine soil particles was 0.15∼6.5% of introduced 137 Cs and dependent on size distribution and solidification degree of the soil layer sample. Therefore, it seems that the amount of 137 Cs which migrates to a long distance with the movement of fine soil particles is small in the case of a fine and solidified soil layer. A trial evaluation of the migration of 137 Cs adsorbed on fine soil particles using the result of the analysis showed that the concentration decreasing effect of Rokkasho's soil layer including the loamy soil layer was larger than that of Tokai's sandy soil layer. (author)

  13. Strong double layer in the downward current region.

    Science.gov (United States)

    Andersson, L.; Ergun, R. E.; Newman, D.; McFadden, J. P.; Carlson, C. W.

    2001-12-01

    A direct observation of a strong double layer has been recorded in detail by the FAST satellite in the downward current region of the aurora. This presentation concentrates on a particular compelling example in which both the electric field and particle measurements clearly illustrate the detail characteristics of the double layer. Electrons with initial energies of about 50 eV are observed to be accelerated through the double layer into a beam of more than 750 eV. This beam is rapidly plateaued by intense wave turbulence into a extended power law distribution. This process forms accelerated `flat-top' electron distributions, which are represented of energized distributions in the downward current region. Ions are also observed to be accelerated by the double layer in the opposite direction of the electron beam. Ion conics on the low potential side of the double layer are trapped between the double layer and their mirror points. The double layer is observed to move up the magnetic field line, in the direction of the electron beam. In front of it, an ion population moves with the speed of the double layer suggesting an overshoot in the potential ramp. The intense wave turbulence on the high potential side is seen to transform into electron phase-space holes far away from the double layer.

  14. The role of adsorbed water on the friction of a layer of submicron particles

    Science.gov (United States)

    Sammis, Charles G.; Lockner, David A.; Reches, Ze’ev

    2011-01-01

    Anomalously low values of friction observed in layers of submicron particles deformed in simple shear at high slip velocities are explained as the consequence of a one nanometer thick layer of water adsorbed on the particles. The observed transition from normal friction with an apparent coefficient near μ = 0.6 at low slip speeds to a coefficient near μ = 0.3 at higher slip speeds is attributed to competition between the time required to extrude the water layer from between neighboring particles in a force chain and the average lifetime of the chain. At low slip speeds the time required for extrusion is less than the average lifetime of a chain so the particles make contact and lock. As slip speed increases, the average lifetime of a chain decreases until it is less than the extrusion time and the particles in a force chain never come into direct contact. If the adsorbed water layer enables the otherwise rough particles to rotate, the coefficient of friction will drop to μ = 0.3, appropriate for rotating spheres. At the highest slip speeds particle temperatures rise above 100°C, the water layer vaporizes, the particles contact and lock, and the coefficient of friction rises to μ = 0.6. The observed onset of weakening at slip speeds near 0.001 m/s is consistent with the measured viscosity of a 1 nm thick layer of adsorbed water, with a minimum particle radius of approximately 20 nm, and with reasonable assumptions about the distribution of force chains guided by experimental observation. The reduction of friction and the range of velocities over which it occurs decrease with increasing normal stress, as predicted by the model. Moreover, the analysis predicts that this high-speed weakening mechanism should operate only for particles with radii smaller than approximately 1 μm. For larger particles the slip speed required for weakening is so large that frictional heating will evaporate the adsorbed water and weakening will not occur.

  15. The architecture of the adsorbed layer at the substrate interface determines the glass transition of supported ultrathin polystyrene films.

    Science.gov (United States)

    Sun, Shuzheng; Xu, Hao; Han, Jun; Zhu, Yumei; Zuo, Biao; Wang, Xinping; Zhang, Wei

    2016-10-12

    To elucidate the mechanism underlying the effect of polymer/solid interfacial interactions on the dynamics of thin polymer films, the glass transition of thin end-functionalized polystyrene films supported on SiO 2 -Si, such as proton-terminated PS (PS-H), α,ω-dicarboxy-terminated PS (PS-COOH), and α,ω-dihydroxyl-terminated PS (PS-OH), was investigated. All the PS films exhibited a substantial depression in T g with decreasing film thickness, while the extent of such depression was strongly dependent on the chemical structure of the end groups and molecular weights. It was found that T - T of the various PS films increased linearly with increasing h ads /R g , in which h ads is the thickness of the interfacial adsorbed layer and R g is the radius of gyration of PS. The h ads /R g is a direct reflection of the macromolecular chain conformation within the adsorbed layer which was affected by its end groups and molecular weights. These findings are in line with the work of Napolitano, and present direct experimental evidence.

  16. Responses of boundary layers to strong external disturbances

    Science.gov (United States)

    Asai, Masahito

    1990-10-01

    The transition from laminar flow to turbulent flow of the boundary layer is an important phenomenon for various problems in astronautical engineering. When the turbulence in the flow is weak, the boundary layer transition starts from the spatial amplification of a viscous T-S (Tollmien Schlichting) wave. The initial wave starts as a two dimensional wave and grows rapidly to a three dimensional wave with amplification. Finally, it corrupts to small scale hairpin eddies. The transitions starting from these wave amplifications are studied, and instability mechanisms are analyzed. In order to analyze the mechanism, the strength of turbulence (eddies) in the air flow that develops a transitional structure in the boundary layer and leads to a turbulent flow transition is analyzed. The responses of the boundary layers to the strong external disturbances are studied experimentally by introducing sonic wave which simulates hairpin eddies in the lower part of the front edge of a flat plate.

  17. Primary events following electron injection into water and adsorbed water layers

    International Nuclear Information System (INIS)

    Barnett, R.N.; Landman, U.; Nitzan, A.

    1990-01-01

    The initial stages of the evolution of an electron injected into bulk water (at 300 K) and into thin water films (1--4 monolayers) adsorbed on a Pt(111) substrate at 50 K are investigated. It is shown that for electrons injected into bulk water with an initial translational kinetic energy between 1.54 and 6.18 eV (i.e., subexcitation energies), the electron momentum time-correlation function left-angle p(0)p(t)right-angle, decays to zero on a time scale of less than 1 fs, reflecting strong backscattering of the electron by the water molecules. On this time scale the electron propagation in the medium is dominated by elastic processes. Furthermore, during this initial stage the system is well represented by a static aqueous medium. Transmission of electrons injected into thin films of adsorbed water is also dominated by elastic scattering. The dependence of the electron transmission probability on the film thickness and the initial injection energy are in accord with recent experimental results of photoinjected electrons into adsorbed water films

  18. Composition of Surface Adsorbed Layer of TiO2 Stored in Ambient Air

    Directory of Open Access Journals (Sweden)

    Zakharenko V.S.

    2017-11-01

    Full Text Available The processes of dark, UV, and visible light promoted desorption of surface species were investigated for three different TiO2 samples: TiO2 prepared by dispersion of the titania single crystal, TiO2 prepared by combustion of a pyrotechnic mixture in air, and commercial TiO2 P25. The composition of the adsorbed layer was identified in the dark and under UV and visible light irradiation. The composition of desorption products showed the dependence of the adsorption layer state on the TiO2 nature. Methane photodesorption was detected only for the commercial TiO2 P25. Possible reasons for methane emission include the capturing of complete molecules during the TiO2 production process and photocatalytic hydrogenation of CO2 under UV-light.

  19. Cellular responses modulated by FGF-2 adsorbed on albumin/heparin layer-by-layer assemblies

    Czech Academy of Sciences Publication Activity Database

    Kumorek, Marta M.; Kubies, Dana; Filová, Elena; Houska, Milan; Kasoju, Naresh; Mázl Chánová, Eliška; Matějka, Roman; Krýslová, Markéta; Bačáková, Lucie; Rypáček, František

    2015-01-01

    Roč. 10, č. 5 (2015), e0125484_1-e0125484_23 E-ISSN 1932-6203 R&D Projects: GA MŠk(CZ) EE2.3.30.0029; GA ČR(CZ) GAP108/11/1857; GA ČR GPP108/12/P624; GA MŠk(CZ) ED1.1.00/02.0109 Institutional support: RVO:61389013 ; RVO:67985823 Keywords : self-assembly * layer-by-layer * heparin Subject RIV: CD - Macromolecular Chemistry; EI - Bio technology ; Bio nics (FGU-C) Impact factor: 3.057, year: 2015

  20. Effect of adsorbed/intercalated anionic dyes into the mechanical properties of PVA: layered zinc hydroxide nitrate nanocomposites.

    Science.gov (United States)

    Marangoni, Rafael; Mikowski, Alexandre; Wypych, Fernando

    2010-11-15

    Zinc hydroxide nitrate (ZHN) was adsorbed with anions of blue dyes (Chicago sky blue, CSB; Evans blue, EB; and Niagara blue, NB) and intercalated with anions of orange dyes (Orange G, OG; Orange II, OII; methyl orange, MO). Transparent, homogeneous and colored nanocomposite films were obtained by casting after dispersing the pigments (dye-intercalated/adsorbed into LHSs) into commercial poly(vinyl alcohol) (PVA). The films were characterized by XRD, UV-Vis spectroscopy, and mechanical testing. The mechanical properties of the PVA compounded with the dye-intercalated/adsorbed ZHN were evaluated, and reasonable increases in Young's modulus and ultimate tensile strength were observed, depending on the amount and choice of layered filler. These results demonstrate the possibility of using a new class of layered hydroxide salts intercalated and adsorbed with anionic dyes to prepare multifunctional polymer nanocomposite materials. Copyright © 2010 Elsevier Inc. All rights reserved.

  1. Polymeric ionic liquid based on magnetic materials fabricated through layer-by-layer assembly as adsorbents for extraction of pesticides.

    Science.gov (United States)

    He, Lijun; Cui, Wenhang; Wang, Yali; Zhao, Wenjie; Xiang, Guoqiang; Jiang, Xiuming; Mao, Pu; He, Juan; Zhang, Shusheng

    2017-11-03

    In this study, layer-by-layer assembly of polyelectrolyte multilayer films on magnetic silica provided a convenient and controllable way to prepare polymeric ionic liquid-based magnetic adsorbents. The resulting particles were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, and magnetic measurements. The data showed that the magnetic particles had more homogeneous spherical shapes with higher saturation magnetization when compared to those obtained by free radical polymerization method. This facilitated the convenient collection of magnetic particles, with higher extraction repeatability. The extraction performance of the multilayer polymeric ionic liquid-based adsorbents was evaluated by magnetic solid-phase extraction of four pesticides including quinalphos, fenthion, phoxim, and chlorpropham. The data suggested that the extraction efficiency depended on the number of layers in the film. The parameters affecting the extraction efficiency were optimized, and good linearity ranging from 2 to 250μgL -1 was obtained with correlation coefficients of 0.9994-0.9998. Moreover, the proposed method presented low limit of detection (0.5μgL -1 , S/N=3) and limit of quantification (1.5μgL -1 , S/N=10), and good repeatability expressed by the relative standard deviation (2.0%-4.6%, n=5). The extraction recoveries of four pesticides were found to range from 58.9% to 85.8%. The reliability of the proposed method was demonstrated by analyzing environmental water samples, and the results revealed satisfactory spiked recovery, relative standard deviation, and selectivity. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Ultra-Thin Optically Transparent Carbon Electrodes Produced from Layers of Adsorbed Proteins

    Science.gov (United States)

    Alharthi, Sarah A.; Benavidez, Tomas E.; Garcia, Carlos D.

    2013-01-01

    This work describes a simple, versatile, and inexpensive procedure to prepare optically transparent carbon electrodes, using proteins as precursors. Upon adsorption, the protein-coated substrates were pyrolyzed under reductive conditions (5% H2) to form ultra-thin, conductive electrodes. Because proteins spontaneously adsorb to interfaces forming uniform layers, the proposed method does not require a precise control of the preparation conditions, specialized instrumentation, or expensive precursors. The resulting electrodes were characterized by a combination of electrochemical, optical, and spectroscopic means. As a proof-of-concept, the optically-transparent electrodes were also used as substrate for the development of an electrochemical glucose biosensor. The proposed films represent a convenient alternative to more sophisticated, and less available, carbon-based nanomaterials. Furthermore, these films could be formed on a variety of substrates, without classical limitations of size or shape. PMID:23421732

  3. Large linear magnetoresistivity in strongly inhomogeneous planar and layered systems

    International Nuclear Information System (INIS)

    Bulgadaev, S.A.; Kusmartsev, F.V.

    2005-01-01

    Explicit expressions for magnetoresistance R of planar and layered strongly inhomogeneous two-phase systems are obtained, using exact dual transformation, connecting effective conductivities of in-plane isotropic two-phase systems with and without magnetic field. These expressions allow to describe the magnetoresistance of various inhomogeneous media at arbitrary concentrations x and magnetic fields H. All expressions show large linear magnetoresistance effect with different dependencies on the phase concentrations. The corresponding plots of the x- and H-dependencies of R(x,H) are represented for various values, respectively, of magnetic field and concentrations at some values of inhomogeneity parameter. The obtained results show a remarkable similarity with the existing experimental data on linear magnetoresistance in silver chalcogenides Ag 2+δ Se. A possible physical explanation of this similarity is proposed. It is shown that the random, stripe type, structures of inhomogeneities are the most suitable for a fabrication of magnetic sensors and a storage of information at room temperatures

  4. Adsorbed Layers of D2, H2, O2, and 3He on Graphite Studied by Neutron Scattering

    DEFF Research Database (Denmark)

    Nielsen, Mourits; McTague, J. P.; Ellenson, W. D.

    1977-01-01

    The phase diagrams of adsorbed monolayers of D2, H2, O2, and 3He on graphite have been measured by neutron diffraction. H2 and D2-layers have a registered √3 structure at low coverages, and at monolayer completion they have a dense triangular structure, which is incommensurate with the substrate...

  5. Layered Double Hydroxides as Effective Adsorbents for U(VI and Toxic Heavy Metals Removal from Aqueous Media

    Directory of Open Access Journals (Sweden)

    G. N. Pshinko

    2013-01-01

    Full Text Available Capacities of different synthesized Zn,Al-hydrotalcite-like adsorbents, including the initial carbonate [Zn4Al2(OH12]·CO3·8H2O and its forms intercalated with chelating agents (ethylenediaminetetraacetic acid (EDTA, diethylenetriaminepentaacetic acid (DTPA, and hexamethylenediaminetetraacetic acid (HMDTA and heat-treated form Zn4Al2O7, to adsorb uranium(VI and ions of toxic heavy metals have been compared. Metal sorption capacities of hydrotalcite-like adsorbents have been shown to correlate with the stability of their complexes with the mentioned chelating agents in a solution. The synthesized layered double hydroxides (LDHs containing chelating agents in the interlayer space are rather efficient for sorption purification of aqueous media free from U(VI irrespective of its forms of natural abundance (including water-soluble bi- and tricarbonate forms and from heavy metal ions. [Zn4Al2(OH12]·EDTA·nH2O is recommended for practical application as one of the most efficient and inexpensive synthetic adsorbents designed for recovery of both cationic and particularly important anionic forms of U(VI and other heavy metals from aqueous media. Carbonate forms of LDHs turned out to be most efficient for recovery of Cu(II from aqueous media with pH0≥7 owing to precipitation of Cu(II basic carbonates and Cu(II hydroxides. Chromate ions are efficiently adsorbed from water only by calcinated forms of LDHs.

  6. Pluripotency transcription factor Sox2 is strongly adsorbed by heparin but requires a protein transduction domain for cell internalization

    Energy Technology Data Exchange (ETDEWEB)

    Albayrak, Cem [Department of Chemical Engineering, Stanford University, 381 North-South Mall, Stanford, CA 94305 (United States); Yang, William C. [Department of Bioengineering, Stanford University, 318 Campus Drive, Stanford, CA 94305 (United States); Swartz, James R., E-mail: jswartz@stanford.edu [Department of Chemical Engineering, Stanford University, 381 North-South Mall, Stanford, CA 94305 (United States); Department of Bioengineering, Stanford University, 318 Campus Drive, Stanford, CA 94305 (United States)

    2013-02-15

    Highlights: ► Both R9Sox2 and Sox2 bind heparin with comparable affinity. ► Both R9Sox2 and Sox2 bind to fibroblasts, but only R9Sox2 is internalized. ► Internalization efficiency of R9Sox2 is 0.3% of the administered protein. ► Heparan sulfate adsorption may be part of a mechanism for managing cell death. -- Abstract: The binding of protein transduction domain (PTD)-conjugated proteins to heparan sulfate is an important step in cellular internalization of macromolecules. Here, we studied the pluripotency transcription factor Sox2, with or without the nonaarginine (R9) PTD. Unexpectedly, we observed that Sox2 is strongly adsorbed by heparin and by the fibroblasts without the R9 PTD. However, only the R9Sox2 fusion protein is internalized by the cells. These results collectively show that binding to heparan sulfate is not sufficient for cellular uptake, thereby supporting a recent hypothesis that other proteins play a role in cell internalization of PTD-conjugated proteins.

  7. Effect of Adsorbed Alcohol Layers on the Behavior of Water Molecules Confined in a Graphene Nanoslit: A Molecular Dynamics Study.

    Science.gov (United States)

    Gao, Qingwei; Zhu, Yudan; Ruan, Yang; Zhang, Yumeng; Zhu, Wei; Lu, Xiaohua; Lu, Linghong

    2017-10-24

    With the rapid development of a two-dimensional (2D) nanomaterial, the confined liquid binary mixture has attracted increasing attention, which has significant potential in membrane separation. Alcohol/water is one of the most common systems in liquid-liquid separation. As one of the most focused systems, recent studies have found that ethanol molecules were preferentially adsorbed on the inner surface of the pore wall and formed an adsorbed ethanol layer under 2D nanoconfinement. To evaluate the effect of the alcohol adsorption layer on the mobility of water molecules, molecular simulations were performed to investigate four types of alcohol/water binary mixtures confined under a 20 Å graphene slit. Residence times of the water molecules covering the alcohol layer were in the order of methanol/water molecules and the surrounding water molecules could induce a small degree of damage to the H-bond network of the water molecules covering the alcohol layer, resulting in the long residence time of the water molecules.

  8. Extraordinary Photoluminescence and Strong Temperature/Angle-Dependent Raman Responses in Few-Layer Phosphorene

    OpenAIRE

    Zhang, Shuang; Yang, Jiong; Xu, Renjing; Wang, Fan; Li, Weifeng; Ghufran, Muhammad; Zhang, Yong-wei; Yu, Zongfu; Zhang, Gang; Qin, Qinghua; Lu, Yuerui

    2014-01-01

    Phosphorene is a new family member of two-dimensional materials. We observed strong and highly layer-dependent photoluminescence in few-layer phosphorene (2 to 5 layers). The results confirmed the theoretical prediction that few-layer phosphorene has a direct and layer-sensitive band gap. We also demonstrated that few-layer phosphorene is more sensitive to temperature modulation than graphene and MoS2 in Raman scattering. The anisotropic Raman response in few-layer phosphorene has enabled us ...

  9. Strong Effect of Azodye Layer Thickness on RM-Stabilized Photoalignment

    Science.gov (United States)

    2017-05-21

    Strong Effect of Azodye Layer Thickness on RM-Stabilized Photoalignment Colin McGinty*, Valerie Finnemeyer**, Robert Reich**, Harry Clark...vertical alignment on these substrates. For the thinner BY layers, we do not see this strong evidence of out of plane reorientation. The out of...In this report we show the surprising effect that thin azodye layers demonstrate improved stability over those that are thicker. Figure 6

  10. Extraordinary photoluminescence and strong temperature/angle-dependent Raman responses in few-layer phosphorene.

    Science.gov (United States)

    Zhang, Shuang; Yang, Jiong; Xu, Renjing; Wang, Fan; Li, Weifeng; Ghufran, Muhammad; Zhang, Yong-Wei; Yu, Zongfu; Zhang, Gang; Qin, Qinghua; Lu, Yuerui

    2014-09-23

    Phosphorene is a new family member of two-dimensional materials. We observed strong and highly layer-dependent photoluminescence in few-layer phosphorene (two to five layers). The results confirmed the theoretical prediction that few-layer phosphorene has a direct and layer-sensitive band gap. We also demonstrated that few-layer phosphorene is more sensitive to temperature modulation than graphene and MoS2 in Raman scattering. The anisotropic Raman response in few-layer phosphorene has enabled us to use an optical method to quickly determine the crystalline orientation without tunneling electron microscopy or scanning tunneling microscopy. Our results provide much needed experimental information about the band structures and exciton nature in few-layer phosphorene.

  11. The effect of the adsorbate layer on the work function reduction of gold substrates under external electric fields

    Science.gov (United States)

    He, Xiang; Cheng, Feng; Chen, Zhao-Xu

    2017-12-01

    The interface interaction between the dimethyl sulfide (DMS) molecule and the gold substrate under external electric fields is investigated by density functional theory method. The polarized DMS adsorbate reduces the work function of the gold substrate while the induced substrate dipole upon the adsorption slightly increases the work function. The DMS layer partially shields the Au(111) substrate from the electric fields and the vacuum level of DMS/Au(111) shifts less than of Au(111) in consequence. Under electric fields pointing outward from the Au(111) surface, both the reduction of work function and the adsorption of DMS molecule are enhanced on the surface. We also suggest the possible application of the field-effect transistor (FET) sensor with gold gate for detecting DMS molecule by utilizing the reduction of substrate work function upon adsorption. The effects of coverage and electric field on the theoretical sensitivity of the sensor are also discussed.

  12. Strong modification of the reflection from birefringent layers of semiconductor nanowires by nanoshells

    NARCIS (Netherlands)

    Diedenhofen, S.L.; Algra, R.E.; Bakkers, E.P.A.M.; Gómez Rivas, J.

    2011-01-01

    The propagation of light in layers of vertically aligned nanowires is determined by their unique and extreme optical properties. Depending on the nanowire filling fraction and their diameter, layers of nanowires form strongly birefringent media. This large birefringence gives rise to sharp angle

  13. Interfacial rheological properties of adsorbed protein layers and surfactants: a review

    NARCIS (Netherlands)

    Bos, M.A.; Vliet, van T.

    2001-01-01

    Proteins and low molecular weight (LMW) surfactants are widely used for the physical stabilisation of many emulsions and foam based food products. The formation and stabilisation of these emulsions and foams depend strongly on the interfacial properties of the proteins and the LMW surfactants.

  14. Interfacial rheological properties of adsorbed protein layers and surfactants : a review

    NARCIS (Netherlands)

    Bos, M.A.; Vliet, T. van

    2001-01-01

    Proteins and low molecular weight (LMW) surfactants are widely used for the physical stabilisation of many emulsions and foam based food products. The formation and stabilisation of these emulsions and foams depend strongly on the interfacial properties of the proteins and the LMW surfactants.

  15. Conditional analysis near strong shear layers in DNS of isotropic turbulence at high Reynolds number

    International Nuclear Information System (INIS)

    Ishihara, Takashi; Kaneda, Yukio; Hunt, Julian C R

    2011-01-01

    Data analysis of high resolution DNS of isotropic turbulence with the Taylor scale Reynolds number R λ = 1131 shows that there are thin shear layers consisting of a cluster of strong vortex tubes with typical diameter of order 10η, where η is the Kolmogorov length scale. The widths of the layers are of the order of the Taylor micro length scale. According to the analysis of one of the layers, coarse grained vorticity in the layer are aligned approximately in the plane of the layer so that there is a net mean shear across the layer with a mean velocity jump of the order of the root-mean-square of the fluctuating velocity, and energy dissipation averaged over the layer is larger than ten times the average over the whole flow. The mean and the standard deviation of the energy transfer T(x, κ) from scales larger than 1/κ to scales smaller than 1/κ at position x are largest within the layers (where the most intense vortices and dissipation occur), but are also large just outside the layers (where viscous stresses are weak), by comparison with the average values of T over the whole region. The DNS data are consistent with exterior fluctuation being damped/filtered at the interface of the layer and then selectively amplified within the layer.

  16. Formation of a Molecular Wire Using the Chemically Adsorbed Monomolecular Layer Having Pyrrolyl Groups

    Directory of Open Access Journals (Sweden)

    Kazufumi Ogawa

    2011-01-01

    Full Text Available A molecular wire containing polypyrrolyl conjugate bonds has been prepared by a chemical adsorption technique using 1,1,1-trichloro-12-pyrrolyl-1-siladodecane (PNN and an electrooxidative polymerization technique, and the conductivity of the molecular wire without any dopant has been measured by using AFM/STM at room temperature. When sample dimension measured was about 0.3 nm (thickness of the conductive portion in the PNN monomolecular layer ×100 μm (the average width of an electric path ×2 mm (the distance between Pt positive electrode and the AFM tip covered with Au, the conductivity of the polymerized PNN molecular wire at room temperature was larger than 1.6 × 105 S/cm both in an atmosphere and in a vacuum chamber of 10−5 Torr. The activation energy obtained by Arrhenius' plots was almost zero in the temperature range between 320 and 450 K.

  17. Preparation of weak-light-driven TiO2-based catalysts via adsorbed-layer nanoreactor synthesis and enhancement of their photo-degradation performance in seawater

    Science.gov (United States)

    Wang, Ting; Xu, Zhi-yong; Zhu, Yi-chen; Wu, Li-guang; Yuan, Hao-xuan; Li, Chang-chun; Liu, Ya-yu; Cai, Jing

    2017-11-01

    Graphene oxide (GO) was first employed as a support in preparing TiO2 nanoparticles by adsorbed-layer nanoreactor synthesis (ALNS). Both TiO2 crystallization and GO reduction simultaneously occurred during solvothermal treatment with alcohol as a solvent. By transmission electron microscopy, high resolution transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and photoluminescence spectroscopy, the results showed that TiO2 nanoparticles with less than 10 nm of size distributed very homogeneously on the GO surface. Tight interaction between TiO2 particles and GO surface could effectively inhibit the aggregation of TiO2 particles, during solvothermal treatment for anatase TiO2 formation. Alcohol could also reduce oxygenated functional groups on GO surface after solvothermal treatment. TiO2 particles with small size and the decrease in oxygenated functional groups on the GO surface both caused high separation efficiency of photo-generated charge carriers, thus resulting in high photo-degradation performance of catalysts. Strong phenol adsorption on photocatalyst was key to enhancing photo-degradation efficiency for phenol in seawater. Moreover, the change in catalyst structure was minimal at different temperatures of solvothermal treatment. But, the degradation rate and efficiency for phenol in seawater were obviously enhanced because of the sensitive structure-activity relationship of catalysts under weak-light irradiation.

  18. Experimental observations of strong double layers. [in triple plasma device for lower magnetospheric simulation

    Science.gov (United States)

    Coakley, P.; Hershkowitz, N.; Hubbard, R.; Joyce, G.

    1978-01-01

    A computer simulation is applied to the production of strong electric potential double layers (DL) in a triple plasma device. The simulation is intended to represent DL in the low magnetosphere above the auroral zones. The DL are described as standing electrostatic shocks with different energy coefficients in their strong and weak forms. The strong DL was generally found to be unstable, but stability could be imparted if a population of trapped electrons was presented. Stability increased with the length of the system. A schematic for the system is presented, and a phase-space plot of electrons (indicating system stability) is graphed.

  19. A Neutron-Diffraction Study of the Solid Layers at the Liquid Solid Boundary in 4He-Films Adsorbed on Graphite

    DEFF Research Database (Denmark)

    da Costa Carneiro, Kim; Passell, L.; Thomlinson, W.

    1981-01-01

    A neutron scattering study of the structure of 4He films adsorbed on graphite is reported. Diffraction from helium monolayers at a temperature of 1.2K shows the formation of an incommensurate, triangular-lattice solid of high density. As the coverage is increased above two layers, the diffraction...... scattering) and fitting it to a simple structural model. Values for the monolayer height above the graphite plane and for the lattice constants of the possible bilayer structures are given....

  20. Influence of pore structure and architecture of photo-grafted functional layers on separation performance of cellulose-based macroporous membrane adsorbers.

    Science.gov (United States)

    Wang, Jun; Faber, Rene; Ulbricht, Mathias

    2009-09-11

    New weak cation-exchange membrane adsorbers were prepared via UV-initiated heterogeneous graft copolymerization on Hydrosart macroporous regenerated cellulose membranes. The dynamic performance was investigated in detail with respect to the pore size and pore size distribution of the base membranes, ion-exchange capacity and architecture of the grafted functional layers as well as binding of target proteins. Main characterization methods were pore analysis (BET and permporometry), titration, analysis of protein binding under static conditions including visualization by confocal laser scanning microscopy and chromatographic analysis of dynamic protein binding and system dispersion. The trade-off between static binding capacity of the membrane adsorber and its permeability has partially been overcome by adapted architecture of the grafted functional layer achieved via the introduction of uncharged moieties as spacers and via stabilization of the binding layer by chemical cross-linking. The resulting membranes show only negligible effects of flow rate on dynamic binding capacity. There is no considerable size exclusion effect for large proteins due to mesh size of functional cross-linked layers. Investigation of system dispersion based on breakthrough curves confirms that the adapted grafted layer architecture has drastically reduced the contribution of the membrane to total system dispersion. The optimum pore structure of base membranes in combination with the best suited architecture of functional layers was identified in this study.

  1. The thermodynamic spin magnetization of strongly correlated 2d electrons in a silicon inversion layer

    OpenAIRE

    Prus, O.; Yaish, Y.; Reznikov, M.; Sivan, U.; Pudalov, V.

    2002-01-01

    A novel method invented to measure the minute thermodynamic spin magnetization of dilute two dimensional fermions is applied to electrons in a silicon inversion layer. Interplay between the ferromagnetic interaction and disorder enhances the low temperature susceptibility up to 7.5 folds compared with the Pauli susceptibility of non-interacting electrons. The magnetization peaks in the vicinity of the density where transition to strong localization takes place. At the same density, the suscep...

  2. Layered Yttrium Hydroxide l-Y(OH)3Luminescent Adsorbent for Detection and Recovery of Phosphate from Water over a Wide pH Range.

    Science.gov (United States)

    Kim, Minhee; Kim, Hyunsub; Byeon, Song-Ho

    2017-11-22

    Layered yttrium hydroxide, l-Y(OH) 3 , has been explored as a representative member of the layered rare earth hydroxide family (l-RE(OH) 3 ; RE = rare earths) for removal and recovery of phosphate from aqueous solution. Compared to the hexagonal form, h-Y(OH) 3 , which has a weakly positive surface charge only at low pH, the layered polymorph composed of hydroxocation layers exhibited a high point of zero charge (pH pzc ∼ 11) and significantly enhanced adsorptive ability for anions over a wide pH range. The Langmuir isotherm model and pseudo-second-order kinetic model were adopted to explain the phosphate adsorption on l-Y(OH) 3 . This new adsorbent revealed high capacity, efficiency, stability, selectivity, and reusability in adsorption of phosphate from a single electrolyte as well as natural waters containing competing anions. Essentially complete phosphate recovery from aqueous solutions at low phosphate concentrations (2.0 mg of P/L) was demonstrated with an adsorbent dosage of 0.025-0.5 g/L. The adsorption of phosphate was accompanied by an increase in the solution pH, suggesting a release of OH - ions during the adsorption reaction. In particular, when Ce 3+ and Tb 3+ were co-doped (l-Y(OH) 3 :Ce,Tb), phosphate adsorption led to the characteristic 5 D 4 → 7 F J (J = 6, 5, and 4) emissions of Tb 3+ under commercial 312 nm UV irradiation. The photoluminescence of phosphate-adsorbed l-Y(OH) 3 :Ce,Tb provided evidence of the inner-sphere complexing mechanism involving the formation of Y(Ce,Tb)-O-P bonds through which the energy transfer can occur. The "luminescence-on" behavior of l-Y(OH) 3 :Ce,Tb by phosphate adsorption was employed to detect and recover phosphorus at low concentrations in deionized water, mineral water, tap water, and river water.

  3. Strong composite films with layered structures prepared by casting silk fibroin-graphene oxide hydrogels

    Science.gov (United States)

    Huang, Liang; Li, Chun; Yuan, Wenjing; Shi, Gaoquan

    2013-04-01

    Composite films of graphene oxide (GO) sheets and silk fibroin (SF) with layered structures have been prepared by facile solution casting of SF-GO hydrogels. The as-prepared composite film containing 15% (by weight, wt%) of SF shows a high tensile strength of 221 +/- 16 MPa and a failure strain of 1.8 +/- 0.4%, which partially surpass those of natural nacre. Particularly, this composite film also has a high modulus of 17.2 +/- 1.9 GPa. The high mechanical properties of this composite film can be attributed to its high content of GO (85 wt%), compact layered structure and the strong hydrogen bonding interaction between SF chains and GO sheets.Composite films of graphene oxide (GO) sheets and silk fibroin (SF) with layered structures have been prepared by facile solution casting of SF-GO hydrogels. The as-prepared composite film containing 15% (by weight, wt%) of SF shows a high tensile strength of 221 +/- 16 MPa and a failure strain of 1.8 +/- 0.4%, which partially surpass those of natural nacre. Particularly, this composite film also has a high modulus of 17.2 +/- 1.9 GPa. The high mechanical properties of this composite film can be attributed to its high content of GO (85 wt%), compact layered structure and the strong hydrogen bonding interaction between SF chains and GO sheets. Electronic supplementary information (ESI) available: XPS spectrum of the SF-GO hybrid film, SEM images of lyophilized GO dispersion and the failure surface of GO film. See DOI: 10.1039/c3nr00196b

  4. NEUTRON REFLECTIVITY STUDY OF END-ADSORBED DIBLOCK COPOLYMERS - CROSS-OVER FROM MUSHROOMS TO BRUSHES

    NARCIS (Netherlands)

    FIELD, JB; TOPRAKCIOGLU, C; DAI, L; HADZIIOANNOU, G; SMITH, G; HAMILTON, W

    1992-01-01

    We report neutron reflectivity data on polystyrene-poly(vinyl-2-pyridine) (PS-PVP) diblock copolymers adsorbed onto quartz from the selective solvent toluene (a good solvent for PS, but a poor one for PVP). The PVP > block adsorbs strongly to form a thin layer on the quartz substrate, while the PS

  5. Unexpected strong magnetism of Cu doped single-layer MoS₂ and its origin.

    Science.gov (United States)

    Yun, Won Seok; Lee, J D

    2014-05-21

    The magnetism of the 3d transition-metal (TM) doped single-layer (1L) MoS2, where the Mo atom is partially replaced by the 3d TM atom, is investigated using the first-principles density functional calculations. In a series of 3d TM doped 1L-MoS2's, the induced spin polarizations are negligible for Sc, Ti, and Cr dopings, while the induced spin polarizations are confirmed for V, Mn, Fe, Co, Ni, Cu, and Zn dopings and the systems become magnetic. Especially, the Cu doped system shows unexpectedly strong magnetism although Cu is nonmagnetic in its bulk state. The driving force is found to be a strong hybridization between Cu 3d states and 3p states of neighboring S, which results in an extreme unbalanced spin-population in the spin-split impurity bands near the Fermi level. Finally, we also discuss further issues of the Cu induced magnetism of 1L-MoS2 such as investigation of additional charge states, the Cu doping at the S site instead of the Mo site, and the Cu adatom on the layer (i.e., 1L-MoS2).

  6. Interfacial shear rheology of β-lactoglobulin-Bovine submaxillary mucin layers adsorbed at air/water interface.

    Science.gov (United States)

    Çelebioğlu, Hilal Y; Kmiecik-Palczewska, Joanna; Lee, Seunghwan; Chronakis, Ioannis S

    2017-09-01

    The interfacial rheological properties of solutions of β-lactoglobulin (BLG), as a model food compound, mixed with bovine submaxillary mucin (BSM), a major salivary protein, have been investigated. Time, frequency, stress sweep and flow measurements have been performed at different pHs (7.4, 5.0 and 3.0), to investigate the air/water interfacial properties. All protein layers (BLG, BSM, and BLG-BSM mixtures) formed an elastic network at the air/water interface with low frequency dependence of the interfacial modulus. The results indicated that BLG moves faster as smaller molecule than mucin, and dominate the surface adsorption and the network formation for the BLG-BSM mixtures. Moreover, BLG-BSM protein mixtures exhibited interfacial properties with lower elastic and viscous moduli than BLG, as a result of competitive displacement of BLG proteins with BSMs from the interface. It is suggested that hydrophobic patches of BSM can be imbedded into the BLG monolayer as driven by a strong hydrophobic interaction with air and disrupt the cohesive assembly of BLG, whereas the hydrophilic (negatively charged) parts of the BSM chain are protruding from the interface towards the bulk water. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. Efficient removal of dyes by a novel magnetic Fe{sub 3}O{sub 4}/ZnCr-layered double hydroxide adsorbent from heavy metal wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Dan; Li, Yang; Zhang, Jia [School of Environmental and Chemical Engineering, Shanghai University, No. 99 Shangda Road, Shanghai 200444 (China); Li, Wenhui [Department of Chemistry, East China University of Science and Technology, 130 Meilong Road, Shanghai 200237 (China); Zhou, Jizhi; Shao, Li [School of Environmental and Chemical Engineering, Shanghai University, No. 99 Shangda Road, Shanghai 200444 (China); Qian, Guangren, E-mail: grqian@shu.edu.cn [School of Environmental and Chemical Engineering, Shanghai University, No. 99 Shangda Road, Shanghai 200444 (China)

    2012-12-15

    Graphical abstract: To purify heavy metal wastewater (pickling waste liquor (PWL{sub A} and PWL{sub B}) and electroplating wastewater (EPW{sub C} and EPW{sub D})), a novel magnetic Fe{sub 3}O{sub 4}/ZnCr-LDH material was formed via two-step microwave hydrothermal method (Step 1 and Step 2) and applicable for organic dyes wastewater treatment. Highlights: Black-Right-Pointing-Pointer Fe{sub 3}O{sub 4}/ZnCr-layered double hydroxide adsorbent was produced from wastewater. Black-Right-Pointing-Pointer RSM was successfully applied to the optimization of the preparation conditions. Black-Right-Pointing-Pointer The maximum adsorption capacity of MO was found to be 240.16 mg/g. Black-Right-Pointing-Pointer The MO adsorption mechanism on MFLA was certified. Black-Right-Pointing-Pointer MFLA could be recycled after catalytic regeneration by the oxidation technology. - Abstract: A novel magnetic Fe{sub 3}O{sub 4}/ZnCr-layered double hydroxide adsorbent was produced from electroplating wastewater and pickling waste liquor via a two-step microwave hydrothermal method. Adsorption of methyl orange (MO) from water was studied using this material. The effects of three variables have been investigated by a single-factor method. The response surface methodology (RSM) based on Box-Behnken design was successfully applied to the optimization of the preparation conditions. The maximum adsorption capacity of MO was found to be 240.16 mg/g, indicating that this material may be an effective adsorbent. It was shown that 99% of heavy metal ions (Fe{sup 2+}, Fe{sup 3+}, Cr{sup 3+}, and Zn{sup 2+}) can be effectively removed into precipitates and released far less in the adsorption process. In addition, this material with adsorbed dye can be easily separated by a magnetic field and recycled after catalytic regeneration with advanced oxidation technology. Meanwhile, kinetic models, FTIR spectra and X-ray diffraction pattern were applied to the experimental data to examine uptake mechanism. The

  8. Pitfalls in velocity analysis for strongly contrasting, layered media - Example from the Chalk Group, North Sea

    Science.gov (United States)

    Montazeri, Mahboubeh; Uldall, Anette; Moreau, Julien; Nielsen, Lars

    2018-02-01

    Knowledge about the velocity structure of the subsurface is critical in key seismic processing sequences, for instance, migration, depth conversion, and construction of initial P- and S-wave velocity models for full-waveform inversion. Therefore, the quality of subsurface imaging is highly dependent upon the quality of the seismic velocity analysis. Based on a case study from the Danish part of the North Sea, we show how interference caused by multiples, converted waves, and thin-layer effects may lead to incorrect velocity estimation, if such effects are not accounted for. Seismic wave propagation inside finely layered reservoir rocks dominated by chalk is described by two-dimensional finite-difference wave field simulation. The rock physical properties used for the modeling are based on an exploration well from the Halfdan field in the Danish sector of the North Sea. The modeling results are compared to seismic data from the study area. The modeling shows that interference of primaries with multiples, converted waves and thin-bed effects can give rise to strong anomalies in standard velocity analysis plots. Consequently, root-mean-square (RMS) velocity profiles may be erroneously picked. In our study area, such mis-picking can introduce errors in, for example, the thickness estimation of the layers near the base of the studied sedimentary strata by 11% to 26%. Tests show that front muting and bandpass filtering cannot significantly improve the quality of velocity analysis in our study. However, we notice that spiking deconvolution applied before velocity analysis may to some extent reduce the impact of interference and, therefore, reduce the risk of erroneous picking of the velocity function.

  9. Evolution of the lower planetary boundary layer over strongly contrasting surfaces

    International Nuclear Information System (INIS)

    Coulter, R.L.; Gao, W.; Martin, T.J.; Shannon, J.D.; Doran, J.C.; Hubbe, J.M.; Shaw, W.M.

    1992-01-01

    In a multilaboratory field study held near Boardman in northeastern Oregon in June 1991, various properties of the surface and lower atmospheric boundary layer over heavily irrigated cropland and adjacent desert steppe were investigated in the initial campaign of the Atmospheric Radiation Measurement (ARM) program. The locale was selected because its disparate characteristics over various spatial scales stress the ability of general circulation models (GCMS) to describe lower boundary conditions, particularly across the discontinuity between desert (in which turbulent flux of heat must be primarily as sensible heat) and large irrigated tracts (in which turbulent flux of latent heat should be the larger term). This campaign of ARM seeks to increase knowledge in three critical areas: (1) determination of the relationships between surface heat fluxes measured over multiple scales and the controlling surface parameters within each scale, (2) integration of local and nearly local heat flux estimates to produce estimates appropriate for GCM grid cells of 100-200 km horizontal dimension, and (3) characterization of the growth and development of the atmospheric boundary layer near transitions between surfaces with strongly contrasting moisture availabilities

  10. Antireflection Coatings for Strongly Curved Glass Lenses by Atomic Layer Deposition

    Directory of Open Access Journals (Sweden)

    Kristin Pfeiffer

    2017-08-01

    Full Text Available Antireflection (AR coatings are indispensable in numerous optical applications and are increasingly demanded on highly curved optical components. In this work, optical thin films of SiO2, Al2O3, TiO2 and Ta2O5 were prepared by atomic layer deposition (ALD, which is based on self-limiting surface reactions leading to a uniform film thickness on arbitrarily shaped surfaces. Al2O3/TiO2/SiO2 and Al2O3/Ta2O5/SiO2 AR coatings were successfully applied in the 400–750 nm and 400–700 nm spectral range, respectively. Less than 0.6% reflectance with an average of 0.3% has been measured on a fused silica hemispherical (half-ball lens with 4 mm diameter along the entire lens surface at 0° angle of incidence. The reflectance on a large B270 aspherical lens with height of 25 mm and diameter of 50 mm decreased to less than 1% with an average reflectance < 0.3%. The results demonstrate that ALD is a promising technology for deposition of uniform optical layers on strongly curved lenses without complex in situ thickness monitoring.

  11. High Hole-Mobility Molecular Layer Made from Strong Electron Acceptor Molecules with Metal Adatoms.

    Science.gov (United States)

    Yamane, Hiroyuki; Kosugi, Nobuhiro

    2017-11-02

    The electronic structure of 7,7,8,8-tetracyanoquinodimethane (TCNQ) and 2,3,5,6-tetrafluoro-TCNQ (F 4 TCNQ) monolayers on Au(111) has been investigated by means of angle-resolved photoemission spectroscopy (ARPES) with synchrotron radiation. In contrast to the physisorbed TCNQ/Au(111) interface, the high-resolution core-level photoemission spectra and the low-energy electron diffraction at the F 4 TCNQ/Au(111) interface show evidence for the strong charge transfer (CT) from Au to F 4 TCNQ and for the Au atom segregation from the underlying Au(111) surface, suggesting a possible origin of the spontaneous formation of the two-dimensional F 4 TCNQ-Au network. The ARPES experiment reveals a low hole-injection barrier and large band dispersion in the CT-induced topmost valence level of the F 4 TCNQ-Au network with 260 meV bandwidth due to the adatom-mediated intermolecular interaction. These results indicate that strong electron acceptor molecules with metal adatoms can form high hole-mobility molecular layers by controlling the molecule-metal ordered structure and their CT interaction.

  12. An ellipsometry study on the effect of aluminium chloride and ferric chloride formulations on mucin layers adsorbed at hydrophobic surfaces.

    Science.gov (United States)

    Hamit-Eminovski, Jildiz; Eskilsson, Krister; Arnebrant, Thomas

    2010-07-01

    Ellipsometry was used to investigate the effect of polyaluminium chloride (PAC) formulations of different degrees of hydrolysation on an adsorbed mucin film. The results were compared to the effect of aluminium chloride (AlCl(3)) and ferric chloride. A compaction of the mucin film took place upon addition of the formulations and this occurred to different extents and at different concentrations for the different formulations. The compaction of PAC of a low degree of hydrolysis behaved similarly to AlCl(3). PAC of a high degree of hydrolysis showed a greater compaction effect than the other aluminium formulations. The initial compaction concentration was found to be 0.001 mM which is less than previously found for aluminium-mucin complex formation in bulk. The reversibility of the compaction was also investigated. The compaction of the mucin film was found to be partly reversible for AlCl(3) and PAC of low degree of hydrolysis. No reversibility was observed for the formulations of PAC of high hydrolysis grade or for ferric chloride. The results are consistent with previously observed effects of PAC of a low degree of hydrolysis on bacterial surfaces where a compaction of surface polymers was indicated by the reduced range of repulsive steric interactions.

  13. Electron stimulated desorption of cations from C sub 6 H sub 6 and C sub 6 H sub 1 sub 2 molecules adsorbed on Pt(1 1 1) and Ar spacer layer

    CERN Document Server

    Kawanowa, H; Hanatani, K; Gotoh, Y; Souda, R

    2003-01-01

    Mechanisms of electron stimulated cation desorption have been investigated for adsorbed C sub 6 H sub 6 and C sub 6 H sub 1 sub 2 molecules on the Pt(1 1 1) surface and the Ar spacer layer formed on it. The ion yields from the molecules adsorbed on the Ar spacer layer are highly enhanced at the smallest coverage and decay steeply with increasing coverage. No such enhancement was observed when they are adsorbed directly on the Pt(1 1 1) substrate. This behavior is explained in terms of the Coulombic repulsion of cations confined in nanoclusters, together with the delocalization of valence holes on the Pt(1 1 1) substrate as well as in the multilayer hydrocarbons. The holes in the C sub 6 H sub 6 molecule are more delocalized than those in the C sub 6 H sub 1 sub 2 molecule due to the overlap of pi orbitals.

  14. Vacuum space charge effects in sub-picosecond soft X-ray photoemission on a molecular adsorbate layer

    International Nuclear Information System (INIS)

    Dell'Angela, M.; Anniyev, T.; Coffee, R.; Föhlisch, A.; Nilsson, A.; Nordlund, D.; Wolf, M.; Wurth, W.

    2015-01-01

    Vacuum space charge-induced kinetic energy shifts of O 1s and Ru 3d core levels in femtosecond soft X-ray photoemission spectra (PES) have been studied at a free electron laser (FEL) for an oxygen layer on Ru(0001). We fully reproduced the measurements by simulating the in-vacuum expansion of the photoelectrons and demonstrate the space charge contribution of the high-order harmonics in the FEL beam. Employing the same analysis for 400 nm pump-X-ray probe PES, we can disentangle the delay dependent Ru 3d energy shifts into effects induced by space charge and by lattice heating from the femtosecond pump pulse

  15. Influence of surface chemistry on the structural organization of monomolecular protein layers adsorbed to functionalized aqueous interfaces

    DEFF Research Database (Denmark)

    Lösche, M.; Piepenstock, M.; Diederich, A.

    1993-01-01

    The molecular organization of streptavidin (SA) bound to aqueous surface monolayers of biotin-functionalized lipids and binary lipid mixtures has been investigated with neutron reflectivity and electron and fluorescence microscopy. The substitution of deuterons (2H) for protons (1H), both...... in subphase water molecules and in the alkyl chains of the lipid surface monolayer, was utilized to determine the interface structure on the molecular length scale. In all cases studied, the protein forms monomolecular layers underneath the interface with thickness values of apprx 40 ANG . A systematic...... dependence of the structural properties of such self-assembled SA monolayers on the surface chemistry was observed: the lateral protein density depends on the length of the spacer connecting the biotin moiety and its hydrophobic anchor. The hydration of the lipid head groups in the protein-bound state...

  16. Complex boron redistribution kinetics in strongly doped polycrystalline-silicon/nitrogen-doped-silicon thin bi-layers

    Energy Technology Data Exchange (ETDEWEB)

    Abadli, S. [Department of Electrical Engineering, University Aout 1955, Skikda, 21000 (Algeria); LEMEAMED, Department of Electronics, University Mentouri, Constantine, 25000 (Algeria); Mansour, F. [LEMEAMED, Department of Electronics, University Mentouri, Constantine, 25000 (Algeria); Pereira, E. Bedel [CNRS-LAAS, 7 avenue du colonel Roche, 31077 Toulouse (France)

    2012-10-15

    We have investigated the complex behaviour of boron (B) redistribution process via silicon thin bi-layers interface. It concerns the instantaneous kinetics of B transfer, trapping, clustering and segregation during the thermal B activation annealing. The used silicon bi-layers have been obtained by low pressure chemical vapor deposition (LPCVD) method at 480 C, by using in-situ nitrogen-doped-silicon (NiDoS) layer and strongly B doped polycrystalline-silicon (P{sup +}) layer. To avoid long-range B redistributions, thermal annealing was carried out at relatively low-temperatures (600 C and 700 C) for various times ranging between 30 min and 2 h. To investigate the experimental secondary ion mass spectroscopy (SIMS) doping profiles, a redistribution model well adapted to the particular structure of two thin layers and to the effects of strong-concentrations has been established. The good adjustment of the simulated profiles with the experimental SIMS profiles allowed a fundamental understanding about the instantaneous physical phenomena giving and disturbing the complex B redistribution profiles-shoulders. The increasing kinetics of the B peak concentration near the bi-layers interface is well reproduced by the established model. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  17. Strong interaction between graphene layer and Fano resonance in terahertz metamaterials

    Science.gov (United States)

    Xiao, Shuyuan; Wang, Tao; Jiang, Xiaoyun; Yan, Xicheng; Cheng, Le; Wang, Boyun; Xu, Chen

    2017-05-01

    Graphene has emerged as a promising building block in modern optics and optoelectronics due to its novel optical and electrical properties. In the mid-infrared and terahertz (THz) regime, graphene behaves like metals and supports surface plasmon resonances (SPRs). Moreover, the continuously tunable conductivity of graphene enables active SPRs and gives rise to a range of active applications. However, the interaction between graphene and metal-based resonant metamaterials has not been fully understood. In this work, a simulation investigation on the interaction between the graphene layer and THz resonances supported by the two-gap split ring metamaterials is systematically conducted. The simulation results show that the graphene layer can substantially reduce the Fano resonance and even switch it off, while leaving the dipole resonance nearly unaffected, which is well explained with the high conductivity of graphene. With the manipulation of graphene conductivity via altering its Fermi energy or layer number, the amplitude of the Fano resonance can be modulated. The tunable Fano resonance here together with the underlying physical mechanism can be strategically important in designing active metal-graphene hybrid metamaterials. In addition, the ‘sensitivity’ to the graphene layer of the Fano resonance is also highly appreciated in the field of ultrasensitive sensing, where the novel physical mechanism can be employed in sensing other graphene-like two-dimensional materials or biomolecules with the high conductivity.

  18. Strong piezoelectricity in single-layer graphene deposited on SiO2 grating substrates.

    Science.gov (United States)

    da Cunha Rodrigues, Gonçalo; Zelenovskiy, Pavel; Romanyuk, Konstantin; Luchkin, Sergey; Kopelevich, Yakov; Kholkin, Andrei

    2015-06-25

    Electromechanical response of materials is a key property for various applications ranging from actuators to sophisticated nanoelectromechanical systems. Here electromechanical properties of the single-layer graphene transferred onto SiO2 calibration grating substrates is studied via piezoresponse force microscopy and confocal Raman spectroscopy. The correlation of mechanical strains in graphene layer with the substrate morphology is established via Raman mapping. Apparent vertical piezoresponse from the single-layer graphene supported by underlying SiO2 structure is observed by piezoresponse force microscopy. The calculated vertical piezocoefficient is about 1.4 nm V(-1), that is, much higher than that of the conventional piezoelectric materials such as lead zirconate titanate and comparable to that of relaxor single crystals. The observed piezoresponse and achieved strain in graphene are associated with the chemical interaction of graphene's carbon atoms with the oxygen from underlying SiO2. The results provide a basis for future applications of graphene layers for sensing, actuating and energy harvesting.

  19. Dynamics of cyanophenyl alkylbenzoate molecules in the bulk and in a surface layer adsorbed onto aerosil. Variation of the lengths of the alkyl chain

    Energy Technology Data Exchange (ETDEWEB)

    Frunza, Stefan [National Institute of Materials Physics, R-077125 Magurele (Romania); Schoenhals, Andreas [BAM Federal Institute of Materials Research and Testing, D-12205 Berlin (Germany); Frunza, Ligia, E-mail: lfrunza@infim.ro [National Institute of Materials Physics, R-077125 Magurele (Romania); Beica, Traian; Zgura, Irina; Ganea, Paul [National Institute of Materials Physics, R-077125 Magurele (Romania); Stoenescu, Daniel [Telecom-Bretagne, Departement d' Optique, Technopole Brest-Iroise 29238 Cedex (France)

    2010-06-16

    Graphical abstract: The temperature dependence of the molecular mobility in composites shows an Arrhenius-type regime at low temperature and a glassy-type one at higher temperature separated by a crossover phenomenon. - Abstract: The molecular mobility of 4-butyl- and 4-pentyl-4'-cyanophenyl benzoate (CP4B, CP5B) and their composites prepared from aerosil A380 was investigated by broadband dielectric spectroscopy in a large temperature range. Thermogravimetric and infrared investigations were additionally performed. High silica density (larger than 7 g aerosil/1 g of liquid crystal) was selected to observe a thin layer adsorbed on the surface of the silica particles. The data were compared with those of the member of the series with six carbon atoms in the alkyl tail. Bulk CP4B and CP5B show the dielectric behaviour expected for liquid crystals. For the composites one relaxation process is observed at frequencies much lower than those for the corresponding bulk, which was assigned to the dynamics of the molecules in a surface layer. The temperature dependence of the relaxation rates (and of the dielectric strength) shows a crossover behaviour with two distinguished regimes. At higher temperatures the data obey the Vogel-Fulcher-Tammann law, whereas an Arrhenius law is observed at lower temperature, in a close similarity to the behaviour of a constrained dynamic glass transition. The estimated Vogel and crossover temperature is independent on the tail length, while the activation energy for the low temperature branch increases weakly with increasing the alkyl tail.

  20. Layered Black Phosphorus: Strongly Anisotropic Magnetic, Electronic, and Electron-Transfer Properties.

    Science.gov (United States)

    Sofer, Zdeněk; Sedmidubský, David; Huber, Štěpán; Luxa, Jan; Bouša, Daniel; Boothroyd, Chris; Pumera, Martin

    2016-03-01

    Layered elemental materials, such as black phosphorus, exhibit unique properties originating from their highly anisotropic layered structure. The results presented herein demonstrate an anomalous anisotropy for the electrical, magnetic, and electrochemical properties of black phosphorus. It is shown that heterogeneous electron transfer from black phosphorus to outer- and inner-sphere molecular probes is highly anisotropic. The electron-transfer rates differ at the basal and edge planes. These unusual properties were interpreted by means of calculations, manifesting the metallic character of the edge planes as compared to the semiconducting properties of the basal plane. This indicates that black phosphorus belongs to a group of materials known as topological insulators. Consequently, these effects render the magnetic properties highly anisotropic, as both diamagnetic and paramagnetic behavior can be observed depending on the orientation in the magnetic field. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Tunable photonic crystal for THz radiation in layered superconductors: Strong magnetic-field dependence of the transmission coefficient

    International Nuclear Information System (INIS)

    Savel'ev, Sergey; Rakhmanov, A.L.; Nori, Franco

    2006-01-01

    Josephson plasma waves are scattered by the Josephson vortex lattice. This scattering results in a strong dependence, on the in-plane magnetic-field H ab , of the reflection and transmission of THz radiation propagating in layered superconductors. In particular, a tunable band-gap structure (THz photonic crystal) occurs in such a medium. These effects can be used, by varying H ab , for the selective frequency-filtering of THz radiation

  2. Strong perpendicular magnetic anisotropy at FeCoB/MgO interface with an ultrathin HfOx insertion layer

    Science.gov (United States)

    Ou, Yongxi; Ralph, Daniel; Buhrman, Robert

    The realization of robust perpendicular magnetic anisotropy (PMA) in heavy metal(HM)/FeCoB/MgO thin-film heterostructures has enabled a pathway for the implementation of high density memory elements based on perpendicularly magnetized tunnel junctions, and also provides a platform for the study and control of domain walls and of novel magnetic chiral structures such as skyrmions in nanowire structures. Here we report on the achievement of more robust PMA in Ta/FeCoB/MgO heterostructures by the insertion of an ultrathin HfOx passivation layer at the FeCoB/MgO interface. This is accomplished by depositing one to two atomic layers of Hf onto the FeCoB before the subsequent rf sputter deposition of the MgO layer, which fully oxidizes the Hf layer as confirmed by X-ray photoelectron spectroscopy measurements. The result is a strong interfacial perpendicular anisotropy energy density as large as 1.7 erg/cm-2 without any post-fabrication annealing treatment. Similar results have been achieved with the use of W and Pt HM base layers. This work broadens the class and enhances the capabilities of PMA HM/FM heterostructures for spintronics research and applications.

  3. Heat transfer to the adsorbent in solar adsorption cooling device

    Science.gov (United States)

    Pilat, Peter; Patsch, Marek; Papucik, Stefan; Vantuch, Martin

    2014-08-01

    The article deals with design and construction of solar adsorption cooling device and with heat transfer problem in adsorber. The most important part of adsorption cooling system is adsorber/desorber containing adsorbent. Zeolith (adsorbent) type was chosen for its high adsorption capacity, like a coolant was used water. In adsorber/desorber occur, at heating of adsorbent, to heat transfer from heat change medium to the adsorbent. The time required for heating of adsorber filling is very important, because on it depend flexibility of cooling system. Zeolith has a large thermal resistance, therefore it had to be adapted the design and construction of adsorber. As the best shows the tube type of adsorber with double coat construction. By this construction is ensured thin layer of adsorbent and heating is quick in all volume of adsorbent. The process of heat transfer was experimentally measured, but for comparison simulated in ANSYS, too.

  4. Kinetics of conformational changes of fibronectin adsorbed onto model surfaces.

    Science.gov (United States)

    Baujard-Lamotte, L; Noinville, S; Goubard, F; Marque, P; Pauthe, E

    2008-05-01

    Fibronectin (FN), a large glycoprotein found in body fluids and in the extracellular matrix, plays a key role in numerous cellular behaviours. We investigate FN adsorption onto hydrophilic bare silica and hydrophobic polystyrene (PS) surfaces using Fourier transform infrared spectroscopy-attenuated total reflection (FTIR-ATR) in aqueous medium. Adsorption kinetics using different bulk concentrations of FN were followed for 2h and the surface density of adsorbed FN and its time-dependent conformational changes were determined. When adsorption occurs onto the hydrophilic surface, FN molecules keep their native conformation independent of the adsorption conditions, but the amount of adsorbed FN increases with time and the bulk concentration. Although the protein surface density is the same on the hydrophobic PS surface, this has a strong impact on the average conformation of the adsorbed FN layer. Indeed, interfacial hydration changes induced by adsorption onto the hydrophobic surface lead to a decrease in unhydrated beta-sheet content and cause an increase in hydrated beta-strand and hydrated random domain content of adsorbed FN. This conformational change is mainly dependent on the bulk concentration. Indeed, at low bulk concentrations, the secondary structures of adsorbed FN molecules undergo strong unfolding, allowing an extended and hydrated conformation of the protein. At high bulk concentrations, the molecular packing reduces the unfolding of the stereoregular structures of the FN molecules, preventing stronger spreading of the protein.

  5. Effect of Strong Acid Functional Groups on Electrode Rise Potential in Capacitive Mixing by Double Layer Expansion

    KAUST Repository

    Hatzell, Marta C.

    2014-12-02

    © 2014 American Chemical Society. The amount of salinity-gradient energy that can be obtained through capacitive mixing based on double layer expansion depends on the extent the electric double layer (EDL) is altered in a low salt concentration (LC) electrolyte (e.g., river water). We show that the electrode-rise potential, which is a measure of the EDL perturbation process, was significantly (P = 10-5) correlated to the concentration of strong acid surface functional groups using five types of activated carbon. Electrodes with the lowest concentration of strong acids (0.05 mmol g-1) had a positive rise potential of 59 ± 4 mV in the LC solution, whereas the carbon with the highest concentration (0.36 mmol g-1) had a negative rise potential (-31 ± 5 mV). Chemical oxidation of a carbon (YP50) using nitric acid decreased the electrode rise potential from 46 ± 2 mV (unaltered) to -6 ± 0.5 mV (oxidized), producing a whole cell potential (53 ± 1.7 mV) that was 4.4 times larger than that obtained with identical electrode materials (from 12 ± 1 mV). Changes in the EDL were linked to the behavior of specific ions in a LC solution using molecular dynamics and metadynamics simulations. The EDL expanded in the LC solution when a carbon surface (pristine graphene) lacked strong acid functional groups, producing a positive-rise potential at the electrode. In contrast, the EDL was compressed for an oxidized surface (graphene oxide), producing a negative-rise electrode potential. These results established the linkage between rise potentials and specific surface functional groups (strong acids) and demonstrated on a molecular scale changes in the EDL using oxidized or pristine carbons.

  6. A PHYSICAL MODEL OF THE EFFECT OF A SHALLOW WEAK LAYER ON STRONG GROUND MOTION FOR STRIKE-SLIP RUPTURES

    Energy Technology Data Exchange (ETDEWEB)

    JAMES N. BRUNE AND ABDOLRASOOL ANOOSHEHPOOR

    1998-02-23

    We report results of foam-rubber modeling of the effect of a shallow weak layer on ground motion from strike-slip ruptures. Computer modeling of strong ground motion from strike-slip earthquakes has involved somewhat arbitrary assumptions about the nature of slip along the shallow part of the fault (e.g., fixing the slip to be zero along the upper 2 kilometers of the fault plane) in order to match certain strong motion accelerograms. Most modeling studies of earthquake strong ground motion have used what is termed kinematic dislocation modeling. In kinematic modeling the time function for slip on the fault is prescribed, and the response of the layered medium is calculated. Unfortunately, there is no guarantee that the model and the prescribed slip are physically reasonable unless the true nature of the medium and its motions are known ahead of time. There is good reason to believe that in many cases faults are weak along the upper few kilometers of the fault zone and may not be able to maintain high levels of shear strain required for high dynamic energy release during earthquakes. Physical models of faulting, as distinct from numerical or mathematical models, are guaranteed to obey static and dynamic mechanical laws. Foam-rubber modeling studies have been reported in a number of publications. The object of this paper is to present results of physical modeling using a shallow weak layer, in order to verify the physical basis for assuming a long rise time and a reduced high frequency pulse for the slip on the shallow part of faults. It appears a 2-kilometer deep, weak zone along strike-slip faults could indeed reduce the high frequency energy radiated from shallow slip, and that this effect can best be represented by superimposing a small amplitude, short rise-time pulse at the onset of a much longer rise-time slip. A weak zone was modeled by inserting weak plastic layers of a few inches in thickness into the foam rubber model. For the 15 cm weak zone the average

  7. Phase manipulation of Goos–Hänchen shifts in a single-layer of graphene nanostructure under strong magnetic field

    Science.gov (United States)

    Solookinejad, Gh; Jabbari, M.; Panahi, M.; Ahmadi Sangachin, E.

    2017-11-01

    In this paper, we discuss the phase management of Goos–Hänchen (GH) shifts of a probe light through a cavity with a single-layer graphene nanostructure under a strong magnetic field. By using the quantum mechanical density matrix formalism we study the GH shifts of reflected and transmitted light beams. It is realized that negative or positive GH shifts can be achieved simultaneously by tuning some controllable parameters such as relative phase and the Rabi frequency of the applied fields. Moreover, the thickness effect of the cavity structure is considered as an effective parameter for adjusting the GH shifts of reflected and transmitted light beams. We find that by choosing suitable parameters, a maximum negative shift of 4.5 mm and positive shift of 5.4 mm are possible for GH shifts in reflected and transmitted light. Our proposed model may be useful for developing all-optical devices in the infrared region.

  8. Distributions of uranium adsorbed from seawater in spherical polyacrylamidoxime chelating resins

    International Nuclear Information System (INIS)

    Katoh, Shunsaku; Sugasaka, Kazuhiko; Hirotsu, Takahiro; Takai, Nobuharu; Itagaki, Takaharu; Ouchi, Hidenaga.

    1984-01-01

    Distributions of metals adsorbed from seawater in spherical polyacrylamidoxime chelating resins were measured by X-ray micro-analyzer. Distributions of uranium in adsorbents were different according to their gel structure or porosity. In the case of adsorbents with low swelling tendencies, uranium was adsorbed only in the superficial layers of the adsorbents. The amount of adsorbed uranium increased with increasing of contact time, but no uranium was detected in the center of adsorbent even after 331 days. Iron was adsorbed only in the surface layer. Magnesium was detected almost uniformly in all parts of adsorbent. Copper and zinc were detected very little. (author)

  9. Thermodynamics of gas adsorption on solid adsorbents

    International Nuclear Information System (INIS)

    Budrugeac, P.

    1979-01-01

    Starting with several hypotheses about the adsorbtion system and the adsorption phenomenon, a thermodynamic treatment of gas adsorption on solid adsorbants is presented. The relationships for determination from isotherms and calorimetric data of thermodynamic functions are derived. The problem of the phase changes in adsorbed layer is discussed. (author)

  10. Synergistic effect between strongly coupled CoAl layered double hydroxides and graphene for the electrocatalytic reduction of oxygen

    International Nuclear Information System (INIS)

    Wang, Yinling; Wang, Zhangcui; Wu, Xiaoqin; Liu, Xiaowang; Li, Maoguo

    2016-01-01

    Highlights: • CoAl-LDHs were synthesized on the surface of graphene oxide in situ. • The oxygen reduction reaction activity of the catalyst was investigated. • The synergistic effect between CoAl-LDHs and rGO is discussed in detail. • The roles of Co 2+ in the LDHs were clarified. - Abstract: Precious metal-free electrocatalysts with high efficiency and durability for the oxygen reduction reaction (ORR) are strongly desired in the field of energy technology. Herein, the CoAl layered double hydroxides (CoAl-LDHs)/reduced graphene oxide (rGO) composites were successfully prepared by growing CoAl-LDHs on the surface of GO in situ via coprecipitation and subsequently hydrothermal treatment. The structure, composition, morphology and ORR catalytic activity of the CoAl-LDHs/rGO composites were investigated as a function of mass ratios of CoAl-LDHs and GO. The results show that there is an optimum mass ratio of CoAl-LDHs and GO (w CoAl-LDHs :w GO = 1:5) for the ORR catalytic activity, where the electron transfer number for ORR at the CoAl-LDHs/rGO composites reaches to 3.5, closing to the full four-electron process. The synergistic effect between CoAl-LDHs and rGO is discussed in detail and the discussion is instructive for the construction of the better transition metal oxides/carbon composite-based ORR catalysts.

  11. From Near-Neutral to Strongly Stratified: Adequately Modelling the Clear-Sky Nocturnal Boundary Layer at Cabauw

    Science.gov (United States)

    Baas, P.; van de Wiel, B. J. H.; van der Linden, S. J. A.; Bosveld, F. C.

    2018-02-01

    The performance of an atmospheric single-column model (SCM) is studied systematically for stably-stratified conditions. To this end, 11 years (2005-2015) of daily SCM simulations were compared to observations from the Cabauw observatory, The Netherlands. Each individual clear-sky night was classified in terms of the ambient geostrophic wind speed with a 1 m s^{-1} bin-width. Nights with overcast conditions were filtered out by selecting only those nights with an average net radiation of less than - 30 W m^{-2}. A similar procedure was applied to the observational dataset. A comparison of observed and modelled ensemble-averaged profiles of wind speed and potential temperature and time series of turbulent fluxes showed that the model represents the dynamics of the nocturnal boundary layer (NBL) at Cabauw very well for a broad range of mechanical forcing conditions. No obvious difference in model performance was found between near-neutral and strongly-stratified conditions. Furthermore, observed NBL regime transitions are represented in a natural way. The reference model version performs much better than a model version that applies excessive vertical mixing as is done in several (global) operational models. Model sensitivity runs showed that for weak-wind conditions the inversion strength depends much more on details of the land-atmosphere coupling than on the turbulent mixing. The presented results indicate that in principle the physical parametrizations of large-scale atmospheric models are sufficiently equipped for modelling stably-stratified conditions for a wide range of forcing conditions.

  12. Synthetic high-charge organomica: effect of the layer charge and alkyl chain length on the structure of the adsorbed surfactants.

    Science.gov (United States)

    Pazos, M Carolina; Castro, Miguel A; Orta, M Mar; Pavón, Esperanza; Valencia Rios, Jesús S; Alba, María D

    2012-05-15

    A family of organomicas was synthesized using synthetic swelling micas with high layer charge (Na(n)Si(8-n)Al(n)Mg(6)F(4)O(20)·XH(2)O, where n = 2, 3, and 4) exchanged with dodecylammonium and octadecylammonium cations. The molecular arrangement of the surfactant was elucidated on the basis on XRD patterns and DTA. The ordering conformation of the surfactant molecules into the interlayer space of micas was investigated by (13)C, (27)Al, and (29)Si MAS NMR. The arrangement of alkylammonium ions in these high-charge synthetic micas depends on the combined effects of the layer charge of the mica and the chain length of the cation. In the organomicas with dodecylammonium, a transition from a parallel layer to a bilayer-paraffin arrangement is observed when the layer charge of the mica increases. However, when octadecylammonium is the interlayer cation, the molecular arrangement of the surfactant was found to follow the bilayer-paraffin model for all values of layer charge. The amount of ordered conformation all-trans is directly proportional of layer charge.

  13. Anodic etching of GaN based film with a strong phase-separated InGaN/GaN layer: Mechanism and properties

    International Nuclear Information System (INIS)

    Gao, Qingxue; Liu, Rong; Xiao, Hongdi; Cao, Dezhong; Liu, Jianqiang; Ma, Jin

    2016-01-01

    Highlights: • GaN film with a strong phase-separated InGaN/GaN layer was etched by electrochemical etching. • Vertically aligned nanopores in n-GaN films were buried underneath the InGaN/GaN structures. • The relaxation of compressive stress in the MQW structure was found by PL and Raman spectra. - Abstract: A strong phase-separated InGaN/GaN layer, which consists of multiple quantum wells (MQW) and superlattices (SL) layers and can produce a blue wavelength spectrum, has been grown on n-GaN thin film, and then fabricated into nanoporous structures by electrochemical etching method in oxalic acid. Scanning electron microscopy (SEM) technique reveals that the etching voltage of 8 V leads to a vertically aligned nanoporous structure, whereas the films etched at 15 V show branching pores within the n-GaN layer. Due to the low doping concentration of barriers (GaN layers) in the InGaN/GaN layer, we observed a record-low rate of etching (<100 nm/min) and nanopores which are mainly originated from the V-pits in the phase-separated layer. In addition, there exists a horizontal nanoporous structure at the interface between the phase-separated layer and the n-GaN layer, presumably resulting from the high transition of electrons between the barrier and the well (InGaN layer) at the interface. As compared to the as-grown MQW structure, the etched MQW structure exhibits a photoluminescence (PL) enhancement with a partial relaxation of compressive stress due to the increased light-extracting surface area and light-guiding effect. Such a compressive stress relaxation can be further confirmed by Raman spectra.

  14. Anodic etching of GaN based film with a strong phase-separated InGaN/GaN layer: Mechanism and properties

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Qingxue [School of Physics, Shandong University, Jinan, 250100 (China); Liu, Rong [Department of Fundamental Theories, Shandong Institute of Physical Education and Sports, Jinan 250063 (China); Xiao, Hongdi, E-mail: hdxiao@sdu.edu.cn [School of Physics, Shandong University, Jinan, 250100 (China); Cao, Dezhong; Liu, Jianqiang; Ma, Jin [School of Physics, Shandong University, Jinan, 250100 (China)

    2016-11-30

    Highlights: • GaN film with a strong phase-separated InGaN/GaN layer was etched by electrochemical etching. • Vertically aligned nanopores in n-GaN films were buried underneath the InGaN/GaN structures. • The relaxation of compressive stress in the MQW structure was found by PL and Raman spectra. - Abstract: A strong phase-separated InGaN/GaN layer, which consists of multiple quantum wells (MQW) and superlattices (SL) layers and can produce a blue wavelength spectrum, has been grown on n-GaN thin film, and then fabricated into nanoporous structures by electrochemical etching method in oxalic acid. Scanning electron microscopy (SEM) technique reveals that the etching voltage of 8 V leads to a vertically aligned nanoporous structure, whereas the films etched at 15 V show branching pores within the n-GaN layer. Due to the low doping concentration of barriers (GaN layers) in the InGaN/GaN layer, we observed a record-low rate of etching (<100 nm/min) and nanopores which are mainly originated from the V-pits in the phase-separated layer. In addition, there exists a horizontal nanoporous structure at the interface between the phase-separated layer and the n-GaN layer, presumably resulting from the high transition of electrons between the barrier and the well (InGaN layer) at the interface. As compared to the as-grown MQW structure, the etched MQW structure exhibits a photoluminescence (PL) enhancement with a partial relaxation of compressive stress due to the increased light-extracting surface area and light-guiding effect. Such a compressive stress relaxation can be further confirmed by Raman spectra.

  15. Pellet feed adsorbed with the recombinant Lactococcus lactis BFE920 expressing SiMA antigen induced strong recall vaccine effects against Streptococcus iniae infection in olive flounder (Paralichthys olivaceus).

    Science.gov (United States)

    Kim, Daniel; Beck, Bo Ram; Lee, Sun Min; Jeon, Jongsu; Lee, Dong Wook; Lee, Jae Il; Song, Seong Kyu

    2016-08-01

    The aim of this study was to develop a fish feed vaccine that provides effective disease prevention and convenient application. A lactic acid bacterium (LAB), Lactococcus lactis BFE920, was modified to express the SiMA antigen, a membrane protein of Streptococcus iniae. The antigen was engineered to be expressed under the nisin promoter, which is induced by nisin produced naturally by the host LAB. Various sizes (40 ± 3.5 g, 80 ± 2.1 g, and 221 ± 2.4 g) of olive flounder (Paralichthys olivaceus) were vaccinated by feeding the extruded pellet feed, onto which the SiMA-expressing L. lactis BFE920 (1.0 × 10(7) CFU/g) was adsorbed. Vaccine-treated feed was administered twice a day for 1 week, and priming and boosting were performed with a 1-week interval in between. The vaccinated fish had significantly elevated levels of antigen-specific serum antibodies and T cell marker mRNAs: CD4-1, CD4-2, and CD8a. In addition, the feed vaccine significantly induced T cell effector functions, such as the production of IFN-γ and activation of the transcription factor that induces its expression, T-bet. When the flounder were challenged by intraperitoneal infection and bath immersion with S. iniae, the vaccinated fish showed 84% and 82% relative percent survival (RPS), respectively. Furthermore, similar protective effects were confirmed even 3 months after vaccination in a field study (n = 4800), indicating that this feed vaccine elicited prolonged duration of immunopotency. In addition, the vaccinated flounder gained 21% more weight and required 16% less feed to gain a unit of body weight compared to the control group. The data clearly demonstrate that the L. lactis BFE920-SiMA feed vaccine has strong protective effects, induces prolonged vaccine efficacy, and has probiotic effects. In addition, this LAB-based fish feed vaccine can be easily used to target many different pathogens of diverse fish species. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. The Dynamics and Structures of Adsorbed Surfaces

    DEFF Research Database (Denmark)

    Nielsen, M; Ellenson, W. D.; McTague, J. P.

    1978-01-01

    Reviews neutron scattering work performed on films of simple gas atoms and molecules adsorbed primarily on graphite surfaces. Exfoliated graphite substrates such as Grafoil were first used in this kind of measurements about five years ago and new results have been reported at an increasing pace....... Elastic neutron diffraction measurements, determining the two-dimensional structural ordering of the adsorbed films, have been performed on layers of N2, Ar, H2, D2, O2, Kr, and He. Measurements on layers of larger molecules such as CD4 and ND3 have also been reported. Inelastic neutron scattering...... of molecules such as NH3 or the internal modes of adsorbed molecules such as C4H10. Neutron scattering measurements where substrates other than graphite products are used as the adsorbents will not be reviewed here. However, the power of the technique will be demonstrated in an example of H2 physisorbed...

  17. Self-Assembled Layered Supercell Structure of Bi2AlMnO6 with Strong Room-Temperature Multiferroic Properties.

    Energy Technology Data Exchange (ETDEWEB)

    Li, Leigang; Boullay, Philippe; Lu, Ping; Perez, Olivier; Steciuk, Gwladys; Wang, Xuejing; Jian, Jie; Huang, Jijie; Gao, Xingyao; Zhang, Wenrui; Zhang, Xinghang; Wang, Haiyan

    2017-02-01

    Room-temperature (RT) multiferroics, possessing ferroelectricity and ferromagnetism simultaneously at RT, hold great promise in miniaturized devices including sensors, actuators, transducers, and multi-state memories. In this work, we report a novel 2D layered RT multiferroic system with self-assembled layered supercell structure consisting of two mismatch-layered sub-lattices of [Bi3O3+δ] and [MO2]1.84 (M=Al/Mn, simply named as BAMO), i.e., alternative layered stacking of two mutually incommensurate sublattices made of a three-layer-thick Bi-O slab and a one-layer-thick Al/Mn-O octahedra slab along the out-of-plane direction. Strong room-temperature multiferroic responses, e.g., ferromagnetic and ferroelectric properties, have been demonstrated and attributed to the highly anisotropic 2D nature of the non-ferromagnetic and ferromagnetic sublattices which are highly mismatched. The work demonstrates an alternative design approach for new 2D layered oxide materials that hold promises as single-phase multiferroics, 2D oxides with tunable bandgaps, and beyond.

  18. Charge transfer from an adsorbed ruthenium-based photosensitizer through an ultra-thin aluminium oxide layer and into a metallic substrate

    Energy Technology Data Exchange (ETDEWEB)

    Gibson, Andrew J.; Temperton, Robert H.; Handrup, Karsten; Weston, Matthew; Mayor, Louise C.; O’Shea, James N., E-mail: james.oshea@nottingham.ac.uk [School of Physics and Astronomy and Nottingham Nanotechnology and Nanoscience Centre (NNNC), University of Nottingham, Nottingham NG7 2RD (United Kingdom)

    2014-06-21

    The interaction of the dye molecule N3 (cis-bis(isothiocyanato)bis(2,2-bipyridyl-4,4′-dicarbo-xylato) -ruthenium(II)) with the ultra-thin oxide layer on a AlNi(110) substrate, has been studied using synchrotron radiation based photoelectron spectroscopy, resonant photoemission spectroscopy, and near edge X-ray absorption fine structure spectroscopy. Calibrated X-ray absorption and valence band spectra of the monolayer and multilayer coverages reveal that charge transfer is possible from the molecule to the AlNi(110) substrate via tunnelling through the ultra-thin oxide layer and into the conduction band edge of the substrate. This charge transfer mechanism is possible from the LUMO+2 and 3 in the excited state but not from the LUMO, therefore enabling core-hole clock analysis, which gives an upper limit of 6.0 ± 2.5 fs for the transfer time. This indicates that ultra-thin oxide layers are a viable material for use in dye-sensitized solar cells, which may lead to reduced recombination effects and improved efficiencies of future devices.

  19. PENGARUH KOMPOSOSI LAPISAN PADA PERMUKAAN GLOBULA MINYAK EMULSI SEBELUM PENGERINGAN SEMPROT TERHADAP SIFAT-SIFAT MIKROKAMSUL TRIGLISERIDA KAYA ASAM LEMAK W-3 [The Effect of the Composition of Adsorbed Layer at Globule Interface of -3 Fatty Acids Enriched Triglyceride Prior to Spray Drying on its Microcapsule Properties

    Directory of Open Access Journals (Sweden)

    Moch Adnan2

    2005-04-01

    Full Text Available Emulsification is the critical factor in microencapsulation by spray drying method. Sodium caseinate is a protein with good emulsifying properties. The properties could be improved by phospholipids addition in the emulsification. Phospholipids addition which stabilized oil globule might change the composition of adsorbed layer.This research was conducted to analyze the changes in composition at oil globule interface by analyzing emulsion systems of triglyceride enriched by -3 fatty acids at 5% (w/v stabilized by sodium caseinate (10% w/v and addition of phospholipids at 0; 0,5; 1,0; 1,5; 2,0; and 2,5% (w/v. The changes in composition of adsorbed layer could be determined from the changes in phospholipids and adsorbed protein concentrations at oil globule interface. Analyses were done to measure the possibility of casein-phospholipids complex, phospholipids and protein adsorption concentration at interface, and adsorbed protein.The increase of phospholipids concentration in the emulsions stabilized by sodium caseinate changed the composition of adsorbed layer at interface. There was phospholipids increase and adsorbed protein decrease at oil globule interface. These changes were caused by casein-phospholipids complex which that decreased surface activity and displacement protein by phospholipids that was adsorbed at oil globule interface.Changes of composition of casein-phospholipids at oil globule prior to microcapsulation process caused changes in the properties of microcapsule produced. The increasing phospholipids and decreasing casein concentrations at oil globule interface decreased the quality of the microcapsule, including decreasing in microencapsulation efficiency, in oxidative stability, and decreasing in EPA+DHA content.

  20. Evolution of deformation heterogeneity at multiple length scales in a strongly textured zinc layer on galvanized steel

    International Nuclear Information System (INIS)

    Ghosh, A; Gurao, N P

    2015-01-01

    The evolution of heterogeneity of plastic deformation in a zinc layer has been probed at multiple length scales using a battery of characterization tools like X-ray diffraction, electron back scatter diffraction (EBSD) and digital image correlation. The experimental results indicate that plastic deformation is heterogeneous at different length scales and the value of micro, meso and macro strain by different characterization techniques shows a different value. The value of strain determined at the meso and micro length scale from EBSD and X-ray diffraction was negligible, however, the macro-strain as determined from X-ray peak shift was significant. EBSD results showed evidence of profuse {101-bar2} <101-bar1> contraction twinning in the zinc layer with higher intragranular misorientation in the twin compared to the matrix. It is therefore, inferred that the evolution of higher intergranular (between matrix and twin) strain due to prolific contraction twinning contributes to the failure of zinc layer on galvanized steel. (paper)

  1. Strong doping of the n-optical confinement layer for increasing output power of high- power pulsed laser diodes in the eye safe wavelength range

    Science.gov (United States)

    Ryvkin, Boris S.; Avrutin, Eugene A.; Kostamovaara, Juha T.

    2017-12-01

    An analytical model for internal optical losses at high power in a 1.5 μm laser diode with strong n-doping in the n-side of the optical confinement layer is created. The model includes intervalence band absorption by holes supplied by both current flow and two-photon absorption (TPA), as well as the direct TPA effect. The resulting losses are compared with those in an identical structure with a weakly doped waveguide, and shown to be substantially lower, resulting in a significant improvement in the output power and efficiency in the structure with a strongly doped waveguide.

  2. Hypersonic boundary layer in the vicinity of a point of inflection of leading edge on a flat wing in the regime of strong viscous interaction

    Science.gov (United States)

    Dudin, G. N.; Ledovskiy, A. V.

    2013-06-01

    The flow in a spatial hypersonic laminar boundary layer on a planar wing with a point of inflection in the leading edge is considered in the regime of strong viscous-inviscid interaction. The boundary problems are formulated for two cases: self-similar flow near the point of inflection of the leading edge and full three-dimensional (3D) boundary layer on a wing with variable sweep angle. The numerical solution is obtained using the finite-difference method. The results of parametric calculations of influence of a wing shape and the temperature factor on flow characteristics in the boundary layer are presented. The possibility of formation of local regions with high shear stress and heat flux is shown.

  3. Theory of the axi-symmetric extrusion process of multi-layer materials with a strong plastic nonhomogeneity

    OpenAIRE

    J. Piwnik; A. Patejuk

    2008-01-01

    A novel simplified r hcorctical solution is found lor thc strcss starcs accompanying thc proccss of cxt ri~siono f ma![ i-laycr matcrialsunder rhc conditions af axial symmetry. Thc solution i~ bawd nn ~ h mc n dcl of pcrfcct plastic material satisfying thc Trcsca yicld condition.thc Haar-Karman conditions bcing sntisficd in each layer. Thc laycrs arc chnnctcrizcd by difrercnt yicld limits and stmng plasticnonhomogeneity. In thc ncighhoi~rhoorol f thc interfaces conrinuous variation of rhc yic...

  4. Theory of the axi-symmetric extrusion process of multi-layer materials with a strong plastic nonhomogeneity

    Directory of Open Access Journals (Sweden)

    J. Piwnik

    2008-03-01

    Full Text Available A novel simplified r hcorctical solution is found lor thc strcss starcs accompanying thc proccss of cxt ri~siono f ma![ i-laycr matcrialsunder rhc conditions af axial symmetry. Thc solution i~ bawd nn ~ h mc n dcl of pcrfcct plastic material satisfying thc Trcsca yicld condition.thc Haar-Karman conditions bcing sntisficd in each layer. Thc laycrs arc chnnctcrizcd by difrercnt yicld limits and stmng plasticnonhomogeneity. In thc ncighhoi~rhoorol f thc interfaces conrinuous variation of rhc yicld limit i s a~sunicdZ. hc form of thc plastic zonc nndpsitions or the contact surfi~ccss eparating rhc laycrs nrc assumcd. Shcaring strcsscs and mcan prcssurc in a longitudinal scclion o f t hccxrruded rod arc cxprcsscd in tcrms of filnctions of the axial coordinatc z. Unknown fttnctions of thc singlc coordinatc z arc dctcrmincdFrom thc yicld conditions writtcn for thc contour of thc die. Accitratc analytical relations arc dcrivcd For tllc normal strcss distribution atthc surface of contact bctwccn thc dic and thc matcrial cxlrudcd, Using thc known normal and shcar stress dislrihutions (due to Iriclion,accuratc valuc of thc lower cstimate of thc cxtrusion forcc is dctcrrnincd. Thc sotution may hc applicd lo ~ h cca scs of arbitrary numhcr oflaycrs and arbitrary h rm oithc dic. I t may bc used to a rational analysis o f ~ h pcro ccss of cxirnsiol~o f multi-lnycr cylindrical rods.

  5. How Irreversible Heat Transport Processes Drive Earth's Interdependent Thermal, Structural, and Chemical Evolution Providing a Strongly Heterogeneous, Layered Mantle

    Science.gov (United States)

    Hofmeister, A.; Criss, R. E.

    2013-12-01

    Because magmatism conveys radioactive isotopes plus latent heat rapidly upwards while advecting heat, this process links and controls the thermal and chemical evolution of Earth. We present evidence that the lower mantle-upper mantle boundary is a profound chemical discontinuity, leading to observed heterogeneities in the outermost layers that can be directly sampled, and construct an alternative view of Earth's internal workings. Earth's beginning involved cooling via explosive outgassing of substantial ice (mainly CO) buried with dust during accretion. High carbon content is expected from Solar abundances and ice in comets. Reaction of CO with metal provided a carbide-rich core while converting MgSiO3 to olivine via oxidizing reactions. Because thermodynamic law (and buoyancy of hot particles) indicates that primordial heat from gravitational segregation is neither large nor carried downwards, whereas differentiation forced radioactive elements upwards, formation of the core and lower mantle greatly cooled the Earth. Reference conductive geotherms, calculated using accurate and new thermal diffusivity data, require that heat-producing elements are sequestered above 670 km which limits convection to the upper mantle. These irreversible beginnings limit secular cooling to radioactive wind-down, permiting deduction of Earth's inventory of heat-producing elements from today's heat flux. Coupling our estimate for heat producing elements with meteoritic data indicates that Earth's oxide content has been underestimated. Density sorting segregated a Si-rich, peridotitic upper mantle from a refractory, oxide lower mantle with high Ca, Al and Ti contents, consistent with diamond inclusion mineralogy. Early and rapid differentiation means that internal temperatures have long been buffered by freezing of the inner core, allowing survival of crust as old as ca.4 Ga. Magmatism remains important. Melt escaping though stress-induced fractures in the rigid lithosphere imparts a

  6. Disordered adsorbate phases

    Science.gov (United States)

    Rys, Franz S.

    1985-04-01

    The occurrence of disordered phases at low temperatures in adsorbed monolayers, as shown recently in a domain wall model, is discussed, the main results are summarized and some relevant experimental systems are mentionned.

  7. Observation by conductive-probe atomic force microscopy of strongly inverted surface layers at the hydrogenated amorphous silicon/crystalline silicon heterojunctions

    Science.gov (United States)

    Maslova, O. A.; Alvarez, J.; Gushina, E. V.; Favre, W.; Gueunier-Farret, M. E.; Gudovskikh, A. S.; Ankudinov, A. V.; Terukov, E. I.; Kleider, J. P.

    2010-12-01

    Heterojunctions made of hydrogenated amorphous silicon (a-Si:H) and crystalline silicon (c-Si) are examined by conducting probe atomic force microscopy. Conductive channels at both (n )a-Si:H/(p)c-Si and (p)a-Si:H/(n)c-Si interfaces are clearly revealed. These are attributed to two-dimension electron and hole gases due to strong inversion layers at the c-Si surface in agreement with previous planar conductance measurements. The presence of a hole gas in (p )a-Si:H/(n)c-Si structures implies a quite large valence band offset (EVc-Si-EVa-Si:H>0.25 eV).

  8. Molecular Adsorber Coating

    Science.gov (United States)

    Straka, Sharon; Peters, Wanda; Hasegawa, Mark; Hedgeland, Randy; Petro, John; Novo-Gradac, Kevin; Wong, Alfred; Triolo, Jack; Miller, Cory

    2011-01-01

    A document discusses a zeolite-based sprayable molecular adsorber coating that has been developed to alleviate the size and weight issues of current ceramic puck-based technology, while providing a configuration that more projects can use to protect against degradation from outgassed materials within a spacecraft, particularly contamination-sensitive instruments. This coating system demonstrates five times the adsorption capacity of previously developed adsorber coating slurries. The molecular adsorber formulation was developed and refined, and a procedure for spray application was developed. Samples were spray-coated and tested for capacity, thermal optical/radiative properties, coating adhesion, and thermal cycling. Work performed during this study indicates that the molecular adsorber formulation can be applied to aluminum, stainless steel, or other metal substrates that can accept silicate-based coatings. The coating can also function as a thermal- control coating. This adsorber will dramatically reduce the mass and volume restrictions, and is less expensive than the currently used molecular adsorber puck design.

  9. The dynamics and structures of adsorbed surfaces

    International Nuclear Information System (INIS)

    Nielsen, M.; Ellenson, W.D.; McTague, J.P.

    1978-01-01

    This article reviews neutron scattering work performed on films of simple gas atoms and molecules adsorbed primarily on graphite surfaces. Exfoliated graphite substrates such as Grafoil were first used in this kind of measurements about five years ago and new results have been reported at an increasing pace. Elastic neutron diffraction measurements, determining the two-dimensional structural ordering of the adsorbed films, have been performed on layers of N 2 , Ar, H 2 , D 2 , O 2 , Kr, and He. Measurements on layers of larger molecules such as CD 4 and ND 3 have been reported very recently. Inelastic neutron scattering measurements, studying the dynamics of the adsorbed films are only possible in a few especially favourable cases such as 36 Ar and D 2 films, where the coherent phonon scattering cross-sections are very large. In other cases incoherent scattering from hydrogen can give information about e.g. the mobility of molecules such as NH 3 or the internal modes of adsorbed molecules such as C 4 H 10 . Neutron scattering measurements where substrates other than graphite products are used as the adsorbents will not be reviewed here. However, the power of the technique will be demonstrated in an example of H 2 physisorbed to activated alumina and in an example where hydrogen is chemisorbed to Raney nickel. (author)

  10. Infrared Analysis Of Enzymes Adsorbed Onto Model Surfaces

    Science.gov (United States)

    Story, Gloria M.; Rauch, Deborah S.; Brode, Philip F.; Marcott, Curtis A.

    1989-12-01

    The adsorption of the enzymes, subtilisin BPN' and lysozyme, onto model surfaces was examined using attenuated total reflectance (ATR) infrared (IR) spectroscopy. Using a cylindrical internal reflection (CIRcle) cell with a Germanium (Ge) internal reflection element (IRE), model hydrophilic surfaces were made by plasma cleaning the IRE and model hydrophobic surfaces were made by precoating the IRE with a thin film of polystyrene. Gas chromatography (GC)-IR data collection software was used to monitor adsorption kinetics during the first five minutes after injection of the enzyme into the CIRcle cell. It was found that for both lysozyme and BPN', most of the enzyme that was going to adsorb onto the model surface did so within ten seconds after injection. Nearly an order-of-magnitude more BPN' adsorbed on the hydrophobic Ge surface than the hydrophilic one, while lysozyme adsorbed somewhat more strongly to the hydrophilic Ge surface. Overnight, the lysozyme layer continued to increase in thickness, while BPN' maintained its initial coverage. The appearance of carboxylate bands in some of the adsorbed BPN' spectra suggests the occurrence of peptide bond hydrolysis. A Au/Pd coating on the CIRcle cell o-rings had a significant effect on the adsorption of BPN'. (This coating was applied in an attempt to eliminate interfering Teflon absorption bands.) An apparent electrochemical reaction occurred, involving BPN', Ge, Au/Pd, and the salt solution used to stabilize BPN'. The result of this reaction was enhanced adsorption of the enzyme around the coated o-rings, etching of the Ge IRE at the o-ring site, and some autolysis of the enzyme. No such reaction was observed with lysozyme.

  11. Effects of adsorbed pyridine derivatives and ultrathin atomic-layer-deposited alumina coatings on the conduction band-edge energy of TiO2 and on redox-shuttle-derived dark currents.

    Science.gov (United States)

    Katz, Michael J; Vermeer, Michael J D; Farha, Omar K; Pellin, Michael J; Hupp, Joseph T

    2013-01-15

    Both the adsorption of t-butylpyridine and the atomic-layer deposition of ultrathin conformal coatings of insulators (such as alumina) are known to boost open-circuit photovoltages substantially for dye-sensitized solar cells. One attractive interpretation is that these modifiers significantly shift the conduction-edge energy of the electrode, thereby shifting the onset potential for dark current arising from the interception of injected electrons by solution-phase redox shuttle components such as Co(phenanthroline)(3)(3+) and triiodide. For standard, high-area, nanoporous photoelectrodes, band-edge energies are difficult to measure directly. In contrast, for flat electrodes they are readily accessible from Mott-Schottky analyses of impedance data. Using such electrodes (specifically TiO(2)), we find that neither organic nor inorganic electrode-surface modifiers shift the conduction-band-edge energy sufficiently to account fully for the beneficial effects on electrode behavior (i.e., the suppression of dark current). Additional experiments reveal that the efficacy of ultrathin coatings of Al(2)O(3) arises chiefly from the passivation of redox-catalytic surface states. In contrast, adsorbed t-butylpyridine appears to suppress dark currents mainly by physically blocking access of shuttle molecules to the electrode surface. Studies with other derivatives of pyridine, including sterically and/or electronically diverse derivatives, show that heterocycle adsorption and the concomitant suppression of dark current does not require the coordination of surface Ti(IV) or Al(III) atoms. Notably, the favorable (i.e., negative) shifts in onset potential for the flow of dark current engendered by organic and inorganic surface modifiers are additive. Furthermore, they appear to be largely insensitive to the identity of shuttle molecules.

  12. Ultradispersed and Single-Layered MoS2 Nanoflakes Strongly Coupled with Graphene: An Optimized Structure with High Kinetics for the Hydrogen Evolution Reaction.

    Science.gov (United States)

    Huang, Haoliang; Huang, Junying; Liu, Weipeng; Fang, Yueping; Liu, Yingju

    2017-11-15

    As one of the most promising Pt alternatives for cost-effective hydrogen production, molybdenum disulfide (MoS 2 ), although has been studied extensively to improve its electrocatalytic activity, suffers from scarce active sites, low conductivity, and lack of interaction with substrates. To this end, we anchor ultradispersed and single-layered MoS 2 nanoflakes on graphene sheets via a hybrid intermediate (MoO x -cysteine-graphene oxide), which not only confines the subsequent growth of MoS 2 on the graphene surface but also ensures the intimate interaction between Mo species and graphene at the initial stage. Mo-O-C bond and a possible residual MoO 3-x layer are proposed to comprise the interface bridging the two inherent incompatible phases, MoS 2 and graphene. This strongly coupled structure together with the highly exposed MoS 2 morphology accelerates the electron injection from graphene to the active sites of MoS 2 , and thus the hydrogen evolution reaction (HER) can achieve an overpotential of ∼275 mV at ∼-740 mA cm -2 , and a Pt-like Tafel slope of ∼35 mV dec -1 . Our results shed light on the indispensable role of interfacial interaction within semiconducting material-nanocarbon composites and provide a new insight into the actual activity of MoS 2 toward the HER.

  13. Understanding Trends in Catalytic Activity: The Effect of Adsorbate-Adsorbate Interactions for CO Oxidation Over Transition Metals

    DEFF Research Database (Denmark)

    Grabow, Lars; Larsen, Britt Hvolbæk; Nørskov, Jens Kehlet

    2010-01-01

    Using high temperature CO oxidation as the example, trends in the reactivity of transition metals are discussed on the basis of density functional theory (DFT) calculations. Volcano type relations between the catalytic rate and adsorption energies of important intermediates are introduced...... and the effect of adsorbate-adsorbate interaction on the trends is discussed. We find that adsorbate-adsorbate interactions significantly increase the activity of strong binding metals (left side of the volcano) but the interactions do not change the relative activity of different metals and have a very small...... influence on the position of the top of the volcano, that is, on which metal is the best catalyst....

  14. Evaluation of adsorbents for the Ta-178 generator

    International Nuclear Information System (INIS)

    Neirinckx, R.D.; Johnson, P.C.; Leblanc, A.; Trumper, J.

    1984-01-01

    The currently used Ta-178 generator is based on a radiation sensitive adsorbent and can be eluted about 50 times before W-178 breakthrough becomes unacceptable. The authors evaluated a series of inorganic and organic adsorbents as support for this generator. Hydrated inorganic materials adsorb tantalum very strongly from most aqueous solutions and none was found useful for the W-178/Ta-178 generator. Tantalum complexing agents are not able to desorb tantalum without dissolving the adsorbents to an appreciable extent. Chelating resins with a high affinity for W were investigated because they could reduce the W-178 breakthrough. They also adsorb tantalum too strongly to be suitable as substrates for the Ta-178 generator. The Bio-Rad AG1x8 system was found to be superior to the other tested systems. The effects of autoclaving, complexant additives and prolonged elution on the Ta-178 yield were measured and the chemical breakdown products quantitated

  15. Graphene nanosheets and graphite oxide as promising adsorbents for removal of organic contaminants from aqueous solution.

    Science.gov (United States)

    Ji, Liangliang; Chen, Wei; Xu, Zhaoyi; Zheng, Shourong; Zhu, Dongqiang

    2013-01-01

    Graphenes are an emerging class of carbon nanomaterials whose adsorption properties toward organic compounds have not been well understood. In the present study, graphene nanosheets were prepared by reoxidation and abrupt heating of graphite oxide, which was prepared by sequential chemical oxidation of commercial nonporous graphite powder. Adsorption properties of three aromatic compounds (naphthalene, 2-naphthol, and 1-naphthylamine) and one pharmaceutical compound (tylosin) on graphene nanosheets and graphite oxide were examined to explore the potential of these two adsorbents for the removal of organic contaminants from aqueous solutions. Compared with the literature data of adsorption on carbon nanotubes, adsorption of bulky, flexible tylosin on graphene nanosheets exhibited markedly faster adsorption kinetics, which can be attributed to their opened-up layer structure. Graphene nanosheets and graphite oxide showed similar sequences of adsorption affinity: 1-naphthylamine > 2-naphthol > tylosin > naphthalene (with much larger differences observed on graphite oxide). It was proposed that the strong adsorption of the three aromatic compounds was mainly due to π-π electron donor-acceptor interactions with the graphitic surfaces of adsorbents. Additionally, Lewis acid-base interaction was likely an important factor contributing to the strong adsorption of 1-naphthylamine and tylosin, especially for the O-functionality-abundant graphite oxide. After being normalized on the basis of adsorbent surface area, adsorption affinities of all four tested adsorbates on graphene nanosheets were very close to those on nonporous graphite powder, reflecting complete accessibility of the adsorbent surface area in adsorption. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  16. Comparison of hot Soxhlet and accelerated solvent extractions with microwave and supercritical fluid extractions for the determination of polycyclic aromatic hydrocarbons and nitrated derivatives strongly adsorbed on soot collected inside a diesel particulate filter.

    Science.gov (United States)

    Oukebdane, K; Portet-Koltalo, F; Machour, N; Dionnet, F; Desbène, P L

    2010-06-30

    Several methods of extraction were optimized to extract polycyclic aromatic hydrocarbons (PAHs), their nitrated derivatives and heavy n-alkanes from a highly adsorptive particulate matter resulting from the combustion of diesel fuel in a diesel engine. This particular carbonaceous particulate matter, collected at high temperatures in cordierite diesel particulate filters (DPF), which are optimized for removing diesel particles from diesel engine exhaust emissions, appeared extremely refractory to extractions using the classical extracting conditions for these pollutants. In particular, the method of accelerated solvent extraction (ASE) is described in detail here. Optimization was performed through experimental design to understand the impact of each factor studied and the factors' possible interactions on the recovery yields. The conventional extraction technique, i.e., Soxhlet extraction, was also carried out, but the lack of quantitative extractions led us to use a more effective approach: hot Soxhlet. It appeared that the extraction of the heaviest PAHs and nitroPAHs by either the optimized ASE or hot Soxhlet processes was far from complete. To enhance recovery yields, we tested original solvent mixtures of aromatic and heteroaromatic solvents. Thereafter, these two extraction techniques were compared to microwave-assisted extraction (MAE) and supercritical fluid extraction (SFE). In every case, the only solvent mixture that permitted quantitative extraction of the heaviest PAHs from the diesel soot was composed of pyridine and diethylamine, which has a strong electron-donor character. Conversely, the extraction of the nitrated PAHs was significantly improved by the use of an electron-acceptor solvent or by introducing a small amount of acetic acid into the pyridine. It was demonstrated that, for many desirable features, no single extraction technique stound out as the best: ASE, MAE or SFE could all challenge hot Soxhlet for favourable extractions

  17. Metal adsorbent for alkaline etching aqua solutions of Si wafer

    International Nuclear Information System (INIS)

    Tamada, Masao; Ueki, Yuji; Seko, Noriaki; Takeda, Toshihide; Kawano, Shin-ichi

    2012-01-01

    High performance adsorbent is expected to be synthesized for the removal of Ni and Cu ions from strong alkaline solution used in the surface etching process of Si wafer. Fibrous adsorbent was synthesized by radiation-induce emulsion graft polymerization onto polyethylene nonwoven fabric and subsequent amination. The reaction condition was optimized using 30 L reaction vessel and nonwoven fabric, 0.3 m width and 18 m long. The resulting fibrous adsorbent was evaluated by 48 wt% NaOH and KOH contaminated with Ni and Cu ions, respectively. The concentration levels of Ni and Cu ions was reduced to less than 1 μg/kg (ppb) at the flow rate of 10 h −1 in space velocity. The life of adsorbent was 30 times higher than that of the commercialized resin. This novel adsorbent was commercialized as METOLATE ® since the ability of adsorption is remarkably higher than that of commercial resin used practically in Si wafer processing. - Highlights: ► Adsorbent was synthesized by radiation-induced emulsion graft polymerization. ► Degree of grafting reached 120% at the pre-irradiation of 50 kGy. ► The resulting adsorbent removed Ni and Cu ion in strong alkaline solution. ► Adsorbent was commercialized for filter of Si wafer etchant.

  18. Mechanism of melting in submonolayer films of nitrogen molecules adsorbed on the basal planes of graphite

    DEFF Research Database (Denmark)

    Hansen, Flemming Yssing; Bruch, Ludwig Walter; Taub, H.

    1995-01-01

    The melting mechanism in submonolayer films of N-2 molecules adsorbed on the basal planes of graphite is studied using molecular-dynamics simulations. The melting is strongly correlated with the formation of vacancies in the films. As the temperature increases, the edges of the submonolayer patch...... become atomically rough and vacancies are first created there. Then there is an onset temperature at which the vacancies penetrate into the patch. At an intermediate region of coverages similar to 0.3-0.8 commensurate layers, there is sufficient free volume for the film to melt at that temperature...

  19. Simulations of the Static Friction Due to Adsorbed Molecules

    OpenAIRE

    He, Gang; Robbins, Mark O.

    2001-01-01

    The static friction between crystalline surfaces separated by a molecularly thin layer of adsorbed molecules is calculated using molecular dynamics simulations. These molecules naturally lead to a finite static friction that is consistent with macroscopic friction laws. Crystalline alignment, sliding direction, and the number of adsorbed molecules are not controlled in most experiments and are shown to have little effect on the friction. Temperature, molecular geometry and interaction potenti...

  20. Structure of Irreversibly Adsorbed Star Polymers

    Science.gov (United States)

    Akgun, Bulent; Aykan, Meryem Seyma; Canavar, Seda; Satija, Sushil K.; Uhrig, David; Hong, Kunlun

    Formation of irreversibly adsorbed polymer chains on solid substrates have a huge impact on the wetting, glass transition, aging and polymer chain mobility in thin films. In recent years there has been many reports on the formation, kinetics and dynamics of these layers formed by linear homopolymers. Recent studies showed that by varying the number of polymer arms and arm molecular weight one can tune the glass transition temperature of thin polymer films. Using polymer architecture as a tool, the behavior of thin films can be tuned between the behavior of linear chains and soft colloids. We have studied the effect of polymer chain architecture on the structure of dead layer using X-ray reflectivity (XR) and atomic force microscopy. Layer thicknesses and densities of flattened and loosely adsorbed chains has been measured for linear, 4-arm, and 8-arm star polymers with identical total molecular weight as a function of substrate surface energy, annealing temperature and annealing time. Star polymers have been synthesized using anionic polymerization. XR measurements showed that 8-arm star PS molecules form the densest and the thickest dead layers among these three molecules.

  1. High performance Mo adsorbent PZC

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1998-10-01

    We have developed Mo adsorbents for natural Mo(n, {gamma}){sup 99}Mo-{sup 99m}Tc generator. Among them, we called the highest performance adsorbent PZC that could adsorb about 250 mg-Mo/g. In this report, we will show the structure, adsorption mechanism of Mo, and the other useful properties of PZC when you carry out the examination of Mo adsorption and elution of {sup 99m}Tc. (author)

  2. Positronium chemistry in porous adsorbents

    International Nuclear Information System (INIS)

    Foti, G.; Nagy, L.G.; Moravcsik, G.; Schay, G.

    1981-01-01

    Kinetic studies on the annihilation of orthopositronium in porous adsorbents have been performed using lifetime spectroscopy. The positron source applied was 22 Na with 0.2 MBq activity. The adsorbents investigated were silica gels of different particle size and pore structure. The appearance of the long-lived component in the lifetime spectra can be explained by the diffusion of the orthopositronium into the pores affected by the particle size and the pore size of the adsorbent, the coverage on it and the chemical nature of the adsorbate. The long-term aim of the work is to determine and to explain these effects. (author)

  3. Strong visible and near infrared photoluminescence from ZnO nanorods/nanowires grown on single layer graphene studied using sub-band gap excitation

    Science.gov (United States)

    Biroju, Ravi K.; Giri, P. K.

    2017-07-01

    Fabrication and optoelectronic applications of graphene based hybrid 2D-1D semiconductor nanostructures have gained tremendous research interest in recent times. Herein, we present a systematic study on the origin and evolution of strong broad band visible and near infrared (NIR) photoluminescence (PL) from vertical ZnO nanorods (NRs) and nanowires (NWs) grown on single layer graphene using both above band gap and sub-band gap optical excitations. High resolution field emission scanning electron microscopy and X-ray diffraction studies are carried out to reveal the morphology and crystalline quality of as-grown and annealed ZnO NRs/NWs on graphene. Room temperature PL studies reveal that besides the UV and visible PL bands, a new near-infrared (NIR) PL emission band appears in the range between 815 nm and 886 nm (1.40-1.52 eV). X-ray photoelectron spectroscopy studies revealed excess oxygen content and unreacted metallic Zn in the as-grown ZnO nanostructures, owing to the low temperature growth by a physical vapor deposition method. Post-growth annealing at 700 °C in the Ar gas ambient results in the enhanced intensity of both visible and NIR PL bands. On the other hand, subsequent high vacuum annealing at 700 °C results in a drastic reduction in the visible PL band and complete suppression of the NIR PL band. PL decay dynamics of green emission in Ar annealed samples show tri-exponential decay on the nanosecond timescale including a very slow decay component (time constant ˜604.5 ns). Based on these results, the NIR PL band comprising two peaks centered at ˜820 nm and ˜860 nm is tentatively assigned to neutral and negatively charged oxygen interstitial (Oi) defects in ZnO, detected experimentally for the first time. The evidence for oxygen induced trap states on the ZnO NW surface is further substantiated by the slow photocurrent response of graphene-ZnO NRs/NWs. These results are important for tunable light emission, photodetection, and other cutting edge

  4. Eliminating Heavy Metals from Water with NanoSheet Minerals as Adsorbents

    Directory of Open Access Journals (Sweden)

    Shaoxian Song

    2017-12-01

    . Montmorillonite was usually pre-interacted with organics to increase the interlayer space, and then exfoliated to single or several layers by using ultrasonic. Among the nano-sheets, the surfaces are strongly charged negatively, while the edges are positively charged. This characteristic allows the adsorption of cations or anions, as well as the substances with negative or positive charges. Graphite can be oxidized and exfoliated into graphene oxide (GO, which has a huge specific surface area and plentiful of functional groups such as carboxyl, epoxy, carbonyl and hydroxyl, leading to high adsorption capacity to heavy metals in water. Nano-sheet molybdenite is a novel two-dimensional material with single or several layers of MoS2 sheets. The most common method to prepare nano-sheet molybdenite is exfoliated from bulk molybdenite through chemical method based on ion intercalation process. A large quantity of functional groups and S atom on the sheets are the active sites for adsorbing heavy metals in water. Nano-sheet minerals are used as adsorbents in the form of three-dimension hydrogels. They are featured by the huge specific surface area and high adsorption efficiency. In addition, the clean and smooth surfaces allow heavy metals to adsorb directly by film dispersion. Without any barrier of mesopores and micropores, the adsorption rate could be well improved. These characteristics would lead to the extremely large adsorption capacity and high adsorption rate. Currently, nano-sheet minerals as adsorbent is a very hot research topic in the field of heavy metal removal. It is expected that nanosheet minerals will be promising adsorbents in the removal of heavy metals from water.

  5. Organic adsorbates on metal surfaces. PTCDA and NTCDA on AG(110)

    Energy Technology Data Exchange (ETDEWEB)

    Abbasi, Afshin

    2010-02-22

    Polyaromatic molecules functionalized with carboxylic groups have served as model systems for the growth of organic semiconducting films on a large variety of substrates. Most non-reactive substrates allow for a growth mode compatible with the bulk phase of the molecular crystal with two molecules in the unit cell, but some more reactive substrates including Ag(111) and Ag(110) can induce substantial changes in the first monolayer (ML). In the specific case of Ag(110), the adsorbate unit cell of both NTCDA and PTCDA resembles a brickwall structure, with a single molecule in the unit cell. From this finding, it can be concluded that the adsorbate-substrate interaction is stronger than typical inter-molecular binding energies in the respective bulk phases. In the present work, the interactions between small Ag(110) clusters and a single NTCDA or PTCDA molecule are investigated with different ab initio techniques. Four major ingredients contribute to the binding between adsorbate and substrate: Directional bonds between Ag atoms in the topmost layer and the oxygen atoms of the molecule, Pauli repulsion between filled orbitals of molecule and substrate, an attractive van-der-Waals interaction, and a negative net charge on the molecule inducing positive image charges in the substrate, resulting therefore in an attractive Coulomb interaction between these opposite charges. As both Hartree-Fock theory and density functional theory with typical gradient-corrected density functional do not contain any long range correlation energy required for dispersion interactions, we compare these approaches with the fastest numerical technique where the leading term of the van-der-Waals interaction is included, i.e. second order Moeller-Plesset theory (MP2). Both Hartree-Fock and density functional theory result in bended optimized geometries where the adsorbate is interacting mainly via the oxygen atoms, with the core of the molecule repelled from the substrate. Only at the MP2 level

  6. Adsorbed Water Illustration

    Science.gov (United States)

    2008-01-01

    The Thermal and Electrical Conductivity Probe on NASA's Phoenix Mars Lander detected small and variable amounts of water in the Martian soil. In this schematic illustration, water molecules are represented in red and white; soil minerals are represented in green and blue. The water, neither liquid, vapor, nor solid, adheres in very thin films of molecules to the surfaces of soil minerals. The left half illustrates an interpretation of less water being adsorbed onto the soil-particle surface during a period when the tilt, or obliquity, of Mars' rotation axis is small, as it is in the present. The right half illustrates a thicker film of water during a time when the obliquity is greater, as it is during cycles on time scales of hundreds of thousands of years. As the humidity of the atmosphere increases, more water accumulates on mineral surfaces. Thicker films behave increasingly like liquid water. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

  7. SISGR: Improved Electrical Energy Storage with Electrochemical Double Layer Capacitance Based on Novel Carbon Electrodes, New Electrolytes, and Thorough Development of a Strong Science Base

    Energy Technology Data Exchange (ETDEWEB)

    Ruoff, Rodney S. [PI; Alam, Todd M. [co-PI; Bielawski, Christopher W. [co-PI; Chabal, Yves [co-PI; Hwang, Gyeong [co-PI; Ishii, Yoshitaka [co-PI; Rogers, Robin [co-PI

    2014-07-23

    The broad objective of the SISGR program is to advance the fundamental scientific understanding of electrochemical double layer capacitance (EDLC) and thus of ultracapacitor systems composed of a new type of electrode based on chemically modified graphene (CMG) and (primarily) with ionic liquids (ILs) as the electrolyte. Our team has studied the interplay between graphene-based and graphene-derived carbons as the electrode materials in electrochemical double layer capacitors (EDLC) systems on the one hand, and electrolytes including novel ionic liquids (ILs), on the other, based on prior work on the subject.

  8. Electronic structure of benzene adsorbed on Ni and Cu surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Weinelt, M.; Nilsson, A.; Wassdahl, N. [Uppsala Univ. (Sweden)] [and others

    1997-04-01

    Benzene has for a long time served as a prototype adsorption system of large molecules. It adsorbs with the molecular plane parallel to the surface. The bonding of benzene to a transition metal is typically viewed to involve the {pi} system. Benzene adsorbs weakly on Cu and strongly on Ni. It is interesting to study how the adsorption strength is reflected in the electronic structure of the adsorbate-substrate complex. The authors have used X-ray Emission (XE) and X-ray Absorption (XA) spectroscopies to selectively study the electronic states localized on the adsorbed benzene molecule. Using XES the occupied states can be studies and with XAS the unoccupied states. The authors have used beamline 8.0 and the Swedish endstation equipped with a grazing incidence x-ray spectrometer and a partial yield absorption detector. The resolution in the XES and XAS were 0.5 eV and 0.05 eV, respectively.

  9. Black Sprayable Molecular Adsorber Coating

    Data.gov (United States)

    National Aeronautics and Space Administration — The main objective of this technology project is to develop, optimize, and flight qualify a black version of the molecular adsorber coating and a conductive version...

  10. Elution by Le Chatelier's principle for maximum recyclability of adsorbents: applied to polyacrylamidoxime adsorbents for extraction of uranium from seawater.

    Science.gov (United States)

    Oyola, Yatsandra; Vukovic, Sinisa; Dai, Sheng

    2016-05-28

    Amidoxime-based polymer adsorbents have attracted interest within the last decade due to their high adsorption capacities for uranium and other rare earth metals from seawater. The ocean contains an approximated 4-5 billion tons of uranium and even though amidoxime-based adsorbents have demonstrated the highest uranium adsorption capacities to date, they are still economically impractical because of their limited recyclability. Typically, the adsorbed metals are eluted with a dilute acid solution that not only damages the amidoxime groups (metal adsorption sites), but is also not strong enough to remove the strongly bound vanadium, which decreases the adsorption capacity with each cycle. We resolved this challenge by incorporating Le Chatelier's principle to recycle adsorbents indefinitely. We used a solution with a high concentration of amidoxime-like chelating agents, such as hydroxylamine, to desorb nearly a 100% of adsorbed metals, including vanadium, without damaging the metal adsorption sites and preserving the high adsorption capacity. The method takes advantage of knowing the binding mode between the amidoxime ligand and the metal and mimics it with chelating agents that then in a Le Chatelier's manner removes metals by shifting to a new chemical equilibrium. For this reason the method is applicable to any ligand-metal adsorbent and it will make an impact on other extraction technologies.

  11. Neutron and light scattering studies of polymers adsorbed on laponite

    International Nuclear Information System (INIS)

    Nelson, Andrew Robert John

    2002-01-01

    The adsorption of poly(ethylene oxide) (PEO) and various poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (Pluronic) copolymers onto the synthetic clay Laponite, was investigated using Small Angle Neutron Scattering (SANS) and Dynamic Light Scattering (DLS). The Laponite particles are anisotropic, with a relatively high aspect ratio; but are the same order of magnitude in size as the polymer radius of gyration. Consequently, the particles present a radically different adsorption geometry compared to a locally planar interface, that is assumed by the majority of adsorption studies. The PEO homo-polymer formed thin layers, with the layer thickness being much smaller on the face than on the edge of the particle. Furthermore, the face thickness remained constant with increasing molecular weight, unlike the edge thickness, which grew with a small power law dependence on the molecular weight. Although the hydrodynamic thicknesses (DLS) were larger than those observed with SANS, the layer thicknesses were much smaller than that expected for polymer adsorption on spherical particles. Experimentally determined inter-particle structure factors suggested that the adsorbed PEO layers provided a steric repulsion term to the inter-particle interactions. The autocorrelation functions for aggregating Laponite dispersions were followed with DLS. It was found that the stabilisation provided by the adsorbed layer reduced the aggregation rate, with lower molecular weights being most effective. SANS and DLS measurements on Laponite/Pluronic systems revealed that the thickness of the Pluronic layer was the same on the edge and face of the particle. As the Pluronic anchor fraction decreased, and the PEO block molecular weight increased, a growth in the layer size and adsorbed amount was observed. The low anchor fraction Pluronics had higher adsorbed amounts and thicker layers, than the highest M w homo-polymers, demonstrating the importance of the PPO block in the

  12. Two dimensional condensation of argon adsorbed on lamellar halides

    International Nuclear Information System (INIS)

    Millot, Francis.

    1976-03-01

    Lamellar halides such as NiCl 2 , FeCl 2 , NiBr 2 , MnBr 2 , MgBr 2 , CdBr 2 , CoI 2 , FeI 2 , MnI 2 , CaI 2 and PbI 2 were sublimed in a rapid stream of dry nitrogen. The adsorption of argon on such materials shows stepped isotherms which reveal two dimensional condensations. From sets of isotherms the Helmholtz free energy, the internal energy and the entropy of the successive layers are determined. From the entropy of the first layer the role of the potential relief of the adsorbent surface on the structure of the adsorbed layer may be determined while the Helmholtz free energy reveals how the ionic character of the adsorbent governs the attractive force of adsorption. The study of the second third and fourth layers shows that their growth follows quite a different behaviour depending on whether the Van der Waals diameter of argon is greater or smaller than the distance between adjacent anions on the crystal surface. A proposition is made to account for the difference in the critical temperatures of the first and second dense layers in terms of the vibrationnal state of their respective substrate. The occurence for the maximum critical temperature observed of corresponding to a triangular layer 3% more expanded than the (111) plane of solid argon is discussed [fr

  13. Spontaneous and strong multi-layer graphene n-doping on soda-lime glass and its application in graphene-semiconductor junctions

    Science.gov (United States)

    Dissanayake, D. M. N. M.; Ashraf, A.; Dwyer, D.; Kisslinger, K.; Zhang, L.; Pang, Y.; Efstathiadis, H.; Eisaman, M. D.

    2016-01-01

    Scalable and low-cost doping of graphene could improve technologies in a wide range of fields such as microelectronics, optoelectronics, and energy storage. While achieving strong p-doping is relatively straightforward, non-electrostatic approaches to n-dope graphene, such as chemical doping, have yielded electron densities of 9.5 × 1012 e/cm2 or below. Furthermore, chemical doping is susceptible to degradation and can adversely affect intrinsic graphene’s properties. Here we demonstrate strong (1.33 × 1013 e/cm2), robust, and spontaneous graphene n-doping on a soda-lime-glass substrate via surface-transfer doping from Na without any external chemical, high-temperature, or vacuum processes. Remarkably, the n-doping reaches 2.11 × 1013 e/cm2 when graphene is transferred onto a p-type copper indium gallium diselenide (CIGS) semiconductor that itself has been deposited onto soda-lime-glass, via surface-transfer doping from Na atoms that diffuse to the CIGS surface. Using this effect, we demonstrate an n-graphene/p-semiconductor Schottky junction with ideality factor of 1.21 and strong photo-response. The ability to achieve strong and persistent graphene n-doping on low-cost, industry-standard materials paves the way toward an entirely new class of graphene-based devices such as photodetectors, photovoltaics, sensors, batteries, and supercapacitors. PMID:26867673

  14. Spontaneous and strong multi-layer graphene n-doping on soda-lime glass and its application in graphene-semiconductor junctions

    OpenAIRE

    Dissanayake, D. M. N. M.; Ashraf, A.; Dwyer, D.; Kisslinger, K.; Zhang, L.; Pang, Y.; Efstathiadis, H.; Eisaman, M. D.

    2016-01-01

    Scalable and low-cost doping of graphene could improve technologies in a wide range of fields such as microelectronics, optoelectronics, and energy storage. While achieving strong p-doping is relatively straightforward, non-electrostatic approaches to n-dope graphene, such as chemical doping, have yielded electron densities of 9.5???1012 e/cm2 or below. Furthermore, chemical doping is susceptible to degradation and can adversely affect intrinsic graphene?s properties. Here we demonstrate stro...

  15. Membrane adsorber for endotoxin removal

    Directory of Open Access Journals (Sweden)

    Karina Moita de Almeida

    Full Text Available ABSTRACT The surface of flat-sheet nylon membranes was modified using bisoxirane as the spacer and polyvinyl alcohol as the coating polymer. The amino acid histidine was explored as a ligand for endotoxins, aiming at its application for endotoxin removal from aqueous solutions. Characterization of the membrane adsorber, analysis of the depyrogenation procedures and the evaluation of endotoxin removal efficiency in static mode are discussed. Ligand density of the membranes was around 7 mg/g dry membrane, allowing removal of up to 65% of the endotoxins. The performance of the membrane adsorber prepared using nylon coated with polyvinyl alcohol and containing histidine as the ligand proved superior to other membrane adsorbers reported in the literature. The lack of endotoxin adsorption on nylon membranes without histidine confirmed that endotoxin removal was due to the presence of the ligand at the membrane surface. Modified membranes were highly stable, exhibiting a lifespan of approximately thirty months.

  16. Understanding the electric field control of the electronic and optical properties of strongly-coupled multi-layered quantum dot molecules.

    Science.gov (United States)

    Usman, Muhammad

    2015-10-21

    Strongly-coupled quantum dot molecules (QDMs) are widely employed in the design of a variety of optoelectronic, photovoltaic, and quantum information devices. An efficient and optimized performance of these devices demands engineering of the electronic and optical properties of the underlying QDMs. The application of electric fields offers a way to realise such a control over the QDM characteristics for a desired device operation. We performed multi-million-atom atomistic tight-binding calculations to study the influence of electric fields on the electron and hole wave function confinements and symmetries, the ground-state transition energies, the band-gap wavelengths, and the optical transition modes. Electrical fields parallel (Ep) and anti-parallel (Ea) to the growth direction were investigated to provide a comprehensive guide for understanding the electric field effects. The strain-induced asymmetry of the hybridized electron states is found to be weak and can be balanced by applying a small Ea electric field, of the order of 1 kV cm(-1). The strong interdot couplings completely break down at large electric fields, leading to single QD states confined at the opposite edges of the QDM. This mimics a transformation from a type-I band structure to a type-II band structure for the QDMs, which is a critical requirement for the design of intermediate-band solar cells (IBSCs). The analysis of the field-dependent ground-state transition energies reveals that the QDM can be operated both as a high dipole moment device by applying large electric fields and as a high polarizability device under the application of small electric field magnitudes. The quantum confined Stark effect (QCSE) red shifts the band-gap wavelength to 1.3 μm at the 15 kV cm(-1) electric field; however the reduced electron-hole wave function overlaps lead to a decrease in the interband optical transition strengths by roughly three orders of magnitude. The study of the polarisation-resolved optical

  17. Black Sprayable Molecular Adsorber Coating Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This novel molecular adsorber coating would alleviate the size, weight, and complexity issues of traditional molecular adsorber puck.  A flexible tape version...

  18. Alkali (Li, K and Na) and alkali-earth (Be, Ca and Mg) adatoms on SiC single layer

    Science.gov (United States)

    Baierle, Rogério J.; Rupp, Caroline J.; Anversa, Jonas

    2018-03-01

    First-principles calculations within the density functional theory (DFT) have been addressed to study the energetic stability, and electronic properties of alkali and alkali-earth atoms adsorbed on a silicon carbide (SiC) single layer. We observe that all atoms are most stable (higher binding energy) on the top of a Si atom, which moves out of the plane (in the opposite direction to the adsorbed atom). Alkali atoms adsorbed give raise to two spin unpaired electronic levels inside the band gap leading the SiC single layer to exhibit n-type semiconductor properties. For alkaline atoms adsorbed there is a deep occupied spin paired electronic level inside the band gap. These finding suggest that the adsorption of alkaline and alkali-earth atoms on SiC layer is a powerful feature to functionalize two dimensional SiC structures, which can be used to produce new electronic, magnetic and optical devices as well for hydrogen and oxygen evolution reaction (HER and OER, respectively). Furthermore, we observe that the adsorption of H2 is ruled by dispersive forces (van der Waals interactions) while the O2 molecule is strongly adsorbed on the functionalized system.

  19. Applicability of preparative overpressured layer chromatography and direct bioautography in search of antibacterial chamomile compounds.

    Science.gov (United States)

    Móricz, Agnes M; Ott, Péter G; Alberti, Agnes; Böszörményi, Andrea; Lemberkovics, Eva; Szoke, Eva; Kéry, Agnes; Mincsovics, Emil

    2013-01-01

    In situ sample preparation and preparative overpressured layer chromatography (OPLC) fractionation on a 0.5 mm thick adsorbent layer of chamomile flower methanol extract prepurified by conventional gravitation accelerated column chromatography were applied in searching for bioactive components. Sample cleanup in situ on the adsorbent layer subsequent to sample application was performed using mobile phase flow in the opposite direction (the input and output of the eluent was exchanged). The antibacterial effect of the fractions obtained from the stepwise gradient OPLC separation with the flow in the normal direction was evaluated by direct bioautography against two Gram-negative bacteria: the luminescence gene tagged plant pathogenic Pseudomonas syringae pv. maculicola, and the naturally luminescent marine bacterium Vibrio fischeri. The fractions having strong activity were analyzed by SPME-GC/MS and HPLC/MS/MS. Mainly essential oil components, coumarins, flavonoids, phenolic acids, and fatty acids were tentatively identified in the fractions.

  20. Structures of metal nanoparticles adsorbed on MgO(001).II. Pt and Pd

    Czech Academy of Sciences Publication Activity Database

    Goniakowski, J.; Jelea, A.; Mottet, Ch.; Barcaro, G.; Fortunelli, A.; Kuntová, Zdeňka; Nita, F.; Levi, A. C.; Rossi, G.; Ferrando, R.

    2009-01-01

    Roč. 130, č. 17 (2009), 174703/1-174703/9 ISSN 0021-9606 Institutional research plan: CEZ:AV0Z10100521 Keywords : adsorbed layers * epitaxial layers * metal clusters * nanoparticles surface phase transformations Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.093, year: 2009

  1. Adsorbate-metal bond effect on empirical determination of surface plasmon penetration depth.

    Science.gov (United States)

    Kegel, Laurel L; Menegazzo, Nicola; Booksh, Karl S

    2013-05-21

    The penetration depth of surface plasmons is commonly determined empirically from the observed response for adsorbate loading on gold surface plasmon resonance (SPR) substrates. However, changes in the SPR spectrum may originate from both changes in the effective refractive index near the metal surface and changes in the metal permittivity following covalent binding of the adsorbate layer. Herein, the significance of incorporating an additional adsorbate-metal bonding effect in the calculation is demonstrated in theory and in practice. The bonding effect is determined from the nonzero intercept of a SPR shift versus adsorbate thickness calibration and incorporated into the calculation of penetration depth at various excitation wavelengths. Determinations of plasmon penetration depth with and without the bonding response for alkanethiolate-gold are compared and are shown to be significantly different for a thiol monolayer adsorbate system. Additionally, plasmon penetration depth evaluated with bonding effect compensation shows greater consistency over different adsorbate thicknesses and better agreement with theory derived from Maxwell's equation, particularly for adsorbate thicknesses that are much smaller (<5%) than the plasmon penetration depth. The method is also extended to a more practically applicable polyelectrolyte multilayer adsorbate system.

  2. Statistical analysis of high order moments is a turbulent boundary layer with strong density differences; Analyse statistique des moments d'ordre eleve dans une couche limite turbulente en presence de differences de densite importantes

    Energy Technology Data Exchange (ETDEWEB)

    Soudani, A. [Batna Univ., Dept. de Physique, Faculte des Sciences (Algeria); Bessaih, R. [Mentouri-Constantine Univ., Dept. de Genie Mecanique, Faculte des Sciences de l' Ingenieur (Algeria)

    2004-12-01

    The study of turbulent boundary layer with strong differences of density is important for the understanding of practical situations occurring for example in the cooling of turbine blades through the tangential injection of a different gas or in combustion. In order to study the fine structure of wall turbulence in the presence of significant variations of density, a statistical analysis of the experimental data, obtained in a wind tunnel, is carried out. The results show that the relaxation of the skewness factor of u'(S{sub u'}) is carried out more quickly in the external layer than close to the wall, as well for the air injection as for the helium injection. S{sub u'} grows close to the injection slot in an appreciable way and this increase is accentuated for the air injection than for the helium injection. This growth of the skewness factor close to the injection slot can be explained by the increase in the longitudinal convective flux of turbulent energy in this zone. The results show for the distribution of the flatness factor F{sub u'} that there is no significant effect of the density gradient on the intermittent structure of the instantaneous longitudinal velocity in the developed zone, x/{delta} {>=} 5. The statistical analysis carried out in this study shows that the helium injection in the boundary layer generates more violent ejections than in the case of air injection. This result is confirmed by the significant contribution of the ejections to turbulent mass flux.

  3. Atomically Thin Mesoporous Co3O4Layers Strongly Coupled with N-rGO Nanosheets as High-Performance Bifunctional Catalysts for 1D Knittable Zinc-Air Batteries.

    Science.gov (United States)

    Li, Yingbo; Zhong, Cheng; Liu, Jie; Zeng, Xiaoqiao; Qu, Shengxiang; Han, Xiaopeng; Deng, Yida; Hu, Wenbin; Lu, Jun

    2018-01-01

    Under development for next-generation wearable electronics are flexible, knittable, and wearable energy-storage devices with high energy density that can be integrated into textiles. Herein, knittable fiber-shaped zinc-air batteries with high volumetric energy density (36.1 mWh cm -3 ) are fabricated via a facile and continuous method with low-cost materials. Furthermore, a high-yield method is developed to prepare the key component of the fiber-shaped zinc-air battery, i.e., a bifunctional catalyst composed of atomically thin layer-by-layer mesoporous Co 3 O 4 /nitrogen-doped reduced graphene oxide (N-rGO) nanosheets. Benefiting from the high surface area, mesoporous structure, and strong synergetic effect between the Co 3 O 4 and N-rGO nanosheets, the bifunctional catalyst exhibits high activity and superior durability for oxygen reduction and evolution reactions. Compared to a fiber-shaped zinc-air battery using state-of-the-art Pt/C + RuO 2 catalysts, the battery based on these Co 3 O 4 /N-rGO nanosheets demonstrates enhanced and stable electrochemical performance, even under severe deformation. Such batteries, for the first time, can be successfully knitted into clothes without short circuits under external forces and can power various electronic devices and even charge a cellphone. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Extraction of uranium from sea water by means of fibrous complex adsorbents

    International Nuclear Information System (INIS)

    Miyamatsu, Tokuhisa; Oguchi, Noboru; Kanchiku, Yoshihiko; Aoyagi, Takanobu

    1982-01-01

    Fibrous complex adsorbents for uranium extraction from sea water were prepared by introducing titanic acid or basic zinc carbonate as effective constituents into fibrous ion exchangers. A fibrous chelate type adsorbent was also tested. Among the adsorbents examined, the following ones demonstrated excellent properties for the recovery of uranium from sea water. a) A fibrous, weakly acidic cation exchanger was treated with titanyl sulfate in aqueous sulfuric acid solution, which was followed by neutralization to afford a fibrous adsorbent containing titanic acid (QC-1f(Ti)). The adsorption capacity for uranium in sea water was estimated by extrapolation to be 50μg-U/g-Ad or 1170 μg-U/g-Ti. b) A fibrous, strongly acidic cation exchanger was treated in a similar way to afford another type of fibrous adsorbent with titanic acid incorporated (QCS-Ti). The adsorption capacity was estimated by extrapolation to be 20-30 μg-U/g-Ad. (author)

  5. Adsorption of metal adatoms on single-layer phosphorene.

    Science.gov (United States)

    Kulish, Vadym V; Malyi, Oleksandr I; Persson, Clas; Wu, Ping

    2015-01-14

    Single- or few-layer phosphorene is a novel two-dimensional direct-bandgap nanomaterial. Based on first-principles calculations, we present a systematic study on the binding energy, geometry, magnetic moment and electronic structure of 20 different adatoms adsorbed on phosphorene. The adatoms cover a wide range of valences, including s and p valence metals, 3d transition metals, noble metals, semiconductors, hydrogen and oxygen. We find that adsorbed adatoms produce a rich diversity of structural, electronic and magnetic properties. Our work demonstrates that phosphorene forms strong bonds with all studied adatoms while still preserving its structural integrity. The adsorption energies of adatoms on phosphorene are more than twice higher than on graphene, while the largest distortions of phosphorene are only ∼0.1-0.2 Å. The charge carrier type in phosphorene can be widely tuned by adatom adsorption. The unique combination of high reactivity with good structural stability is very promising for potential applications of phosphorene.

  6. Interactions of organic contaminants with mineral-adsorbed surfactants

    Science.gov (United States)

    Zhu, L.; Chen, B.; Tao, S.; Chiou, C.T.

    2003-01-01

    Sorption of organic contaminants (phenol, p-nitrophenol, and naphthalene) to natural solids (soils and bentonite) with and without myristylpyridinium bromide (MPB) cationic surfactant was studied to provide novel insight to interactions of contaminants with the mineral-adsorbed surfactant. Contaminant sorption coefficients with mineral-adsorbed surfactants, Kss, show a strong dependence on surfactant loading in the solid. At low surfactant levels, the Kss values increased with increasing sorbed surfactant mass, reached a maximum, and then decreased with increasing surfactant loading. The Kss values for contaminants were always higher than respective partition coefficients with surfactant micelles (Kmc) and natural organic matter (Koc). At examined MPB concentrations in water the three organic contaminants showed little solubility enhancement by MPB. At low sorbed-surfactant levels, the resulting mineral-adsorbed surfactant via the cation-exchange process appears to form a thin organic film, which effectively "adsorbs" the contaminants, resulting in very high Kss values. At high surfactant levels, the sorbed surfactant on minerals appears to form a bulklike medium that behaves essentially as a partition phase (rather than an adsorptive surface), with the resulting Kss being significantly decreased and less dependent on the MPB loading. The results provide a reference to the use of surfactants for remediation of contaminated soils/sediments or groundwater in engineered surfactant-enhanced washing.

  7. Molecular hydrogen isotopes adsorbed on krypton-preplated graphite

    Science.gov (United States)

    Turnbull, Joseph; Boninsegni, Massimo

    2007-09-01

    Adsorption of ortho-deuterium and para-hydrogen films on a graphite substrate, preplated with a single atomic layer of krypton, is studied theoretically by means of quantum Monte Carlo simulations at low temperature. Our model explicitly includes substrate corrugation. Energetic and structural properties of these adsorbed films are computed for a range of hydrogen coverages. Thermodynamically stable adsorbed films are solid, with no clear evidence of any liquidlike phase. Quantum exchanges of ortho-deuterium and para-hydrogen are essentially absent in this system, down to zero temperature; consequently, this system displays no superfluidity in this limit. Our simulations provide evidence of a stable domain-wall fluid at low temperature, consistent with recent experimental observations.

  8. Formation and composition of adsorbates on hydrophobic carbon surfaces from aqueous laccase-maltodextrin mixture suspension

    International Nuclear Information System (INIS)

    Corrales Ureña, Yendry Regina; Lisboa-Filho, Paulo Noronha; Szardenings, Michael; Gätjen, Linda; Noeske, Paul-Ludwig Michael; Rischka, Klaus

    2016-01-01

    Highlights: • Less than 10 nm layer formed on carbon based materials composed by laccase and maltodextrin. • Improvement of the wettability of carbon based materials. • A protein-polysaccharide biofilm layer formation at solid liquid interface. • Stable layers formed under buffer and water rinsing. - Abstract: A robust procedure for the surface bio-functionalization of carbon surfaces was developed. It consists on the modification of carbon materials in contact with an aqueous suspension of the enzyme laccase from Trametes versicolor and the lyophilization agent maltodextrin, with the pH value adjusted close to the isoelectric point of the enzyme. We report in-situ investigations applying Quartz Crystal Microbalance with Dissipation (QCM-D) for carbon-coated sensor surfaces and, moreover, ex-situ measurements with static contact angle measurements, X-ray Photoelectron Spectroscopy (XPS) and Scanning Force Microscopy (SFM) for smooth Highly Oriented Pyrolytic Graphite (HOPG) substrates, for contact times between the enzyme formulation and the carbon material surface ranging from 20 s to 24 h. QCM-D studies reveals the formation of rigid layer of biomaterial, a few nanometers thin, which shows a strongly improved wettability of the substrate surface upon contact angle measurements. Following spectroscopic characterization, these layers are composed of mixtures of laccase and maltodextrin. The formation of these adsorbates is attributed to attractive interactions between laccase, the maltodextrin-based lyophilization agent and the hydrophobic carbon surfaces; a short-term contact between the aqueous laccase mixture suspension and HOPG surfaces is shown to merely result in de-wetting patterns influencing the results of contact angle measurements. The new enzyme-based surface modification of carbon-based materials is suggested to be applicable for the improvement of not only the wettability of low energy substrate surfaces with fluid formulations like coatings

  9. Formation and composition of adsorbates on hydrophobic carbon surfaces from aqueous laccase-maltodextrin mixture suspension

    Energy Technology Data Exchange (ETDEWEB)

    Corrales Ureña, Yendry Regina, E-mail: yendry386@hotmail.com [UNESP São Paulo State University, Av. Eng. Luiz Edmundo Carrijo Coube, 14-01, Bauru, São Paulo (Brazil); Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM, Wiener Strasse 12, 28359 Bremen (Germany); Lisboa-Filho, Paulo Noronha [UNESP São Paulo State University, Av. Eng. Luiz Edmundo Carrijo Coube, 14-01, Bauru, São Paulo (Brazil); Szardenings, Michael [Fraunhofer Institute for Cell Therapy and Immunology IZI, Perlickstrasse 1, 04103 Leipzig (Germany); Gätjen, Linda; Noeske, Paul-Ludwig Michael; Rischka, Klaus [Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM, Wiener Strasse 12, 28359 Bremen (Germany)

    2016-11-01

    Highlights: • Less than 10 nm layer formed on carbon based materials composed by laccase and maltodextrin. • Improvement of the wettability of carbon based materials. • A protein-polysaccharide biofilm layer formation at solid liquid interface. • Stable layers formed under buffer and water rinsing. - Abstract: A robust procedure for the surface bio-functionalization of carbon surfaces was developed. It consists on the modification of carbon materials in contact with an aqueous suspension of the enzyme laccase from Trametes versicolor and the lyophilization agent maltodextrin, with the pH value adjusted close to the isoelectric point of the enzyme. We report in-situ investigations applying Quartz Crystal Microbalance with Dissipation (QCM-D) for carbon-coated sensor surfaces and, moreover, ex-situ measurements with static contact angle measurements, X-ray Photoelectron Spectroscopy (XPS) and Scanning Force Microscopy (SFM) for smooth Highly Oriented Pyrolytic Graphite (HOPG) substrates, for contact times between the enzyme formulation and the carbon material surface ranging from 20 s to 24 h. QCM-D studies reveals the formation of rigid layer of biomaterial, a few nanometers thin, which shows a strongly improved wettability of the substrate surface upon contact angle measurements. Following spectroscopic characterization, these layers are composed of mixtures of laccase and maltodextrin. The formation of these adsorbates is attributed to attractive interactions between laccase, the maltodextrin-based lyophilization agent and the hydrophobic carbon surfaces; a short-term contact between the aqueous laccase mixture suspension and HOPG surfaces is shown to merely result in de-wetting patterns influencing the results of contact angle measurements. The new enzyme-based surface modification of carbon-based materials is suggested to be applicable for the improvement of not only the wettability of low energy substrate surfaces with fluid formulations like coatings

  10. Effect of adsorbents and chemical treatments on the removal of strontium from aqueous solutions

    International Nuclear Information System (INIS)

    Ahmadpour, A.; Zabihi, M.; Tahmasbi, M.; Bastami, T. Rohani

    2010-01-01

    In the present investigation, three different solid wastes namely almond green hull, eggplant hull, and moss were initially treated and used as adsorbents for the adsorption of strontium ion from aqueous solutions. Adsorbent types and chemical treatments are proved to have effective roles on the adsorption of Sr(II) ion. Among the three adsorbents, almond green hull demonstrated strong affinity toward strontium ion in different solutions. The effectiveness of this new adsorbent was studied in batch adsorption mode under a variety of experimental conditions such as: different chemical treatments, various amounts of adsorbent, and initial metal-ion concentration. The optimum doses of adsorbent for the maximum Sr(II) adsorption were found to be 0.2 and 0.3 g for 45 and 102 mg L -1 solutions, respectively. High Sr(II) adsorption efficiencies were achieved only in the first 3 min of adsorbent's contact time. The kinetics of Sr(II) adsorption on almond green hull was also examined and it was observed that it follows the pseudo second-order behavior. Both Langmuir and Freundlich models well predicted the experimental adsorption isotherm data. The maximum adsorption capacity on almond green hull was found to be 116.3 mg g -1 . The present study also confirmed that these low cost agriculture byproducts could be used as efficient adsorbents for the removal of strontium from wastewater streams.

  11. Influence of hydrophobization of fumed oxides on interactions with polar and nonpolar adsorbates

    Science.gov (United States)

    Gun'ko, V. M.; Pakhlov, E. M.; Goncharuk, O. V.; Andriyko, L. S.; Marynin, A. I.; Ukrainets, A. I.; Charmas, B.; Skubiszewska-Zięba, J.; Blitz, J. P.

    2017-11-01

    A variety of unmodified and modified fumed silica A-300 and silica/titania (ST20 and ST76 at 20 and 76 wt.% of titania, respectively) was prepared to analyze features of their interactions with polar and nonpolar adsorbates. The materials were studied using nitrogen adsorption-desorption, ethanol evaporation kinetics, infrared (IR) spectroscopy, thermogravimetry (TG), photon correlation spectroscopy, differential scanning calorimetry (DSC), DSC and TG thermoporometry, and quantum chemistry. Changes in surface structure of modified nanooxides with increasing hydrophobization degree (ΘMS) from 20% to 100% have a strong affect on the textural characteristics of the materials and adsorption-desorption of various adsorbates. Confined space effects enhanced due to the location of adsorbates in narrow voids between nanoparticles lead to freezing-melting point depression for bound polar and nonpolar adsorbates. The behavior of particles of modified nanooxides in aqueous and water/ethanol media is strongly altered due to enhanced aggregations with increasing value of ΘMS. All of these change are non-monotonic functions of ΘMS which affects (i) rearrangement of nanoparticles, (ii) interactions with polar and nonpolar adsorbates, (iii) location of adsorbates in voids of different sizes, (iv) the clustering of adsorbates and formation of nearly bulk structures.

  12. Neutron reflectivity study of adsorbed diblock copolymers

    International Nuclear Information System (INIS)

    Smith, G.S.; Baker, S.M.; Wages, S.; Hamilton, W.; Toprakcioglu, C.; Field, J.B.; Dai, L.

    1994-01-01

    This paper summarizes our cumulative work on neutron reflectivity studies of polystyrene-poly(vinyl-2-pyridine) (PS-PVP) and polystyrenepolyethylene oxide (PS-PEO) adsorbed at a quartz-solvent interface. Deuterated toluene was chosen as the solvent since it is a good solvent for PS and a poor one for either of the other two blocks. In this case, the polystyrene dangles into the solvent while the other block acts as an anchor. The neutron reflectivity studies reveal that the form of the polymer density profile normal to the substrate may be varied from an extended ''brush'' to a condensed ''mushroom'' conformation by manipulating the ratio of the molecular weights of the two blocks. In addition, we present new data on the PS-PEO system in a poor solvent, deuterated cyclohexane, under conditions of shear flow in Poiseuille geometry. We find that when the PS-PEO diblock is absorbed from cyclohexane and is allowed to relax, the PS chain takes on a ''mushroom'' conformation. However, when the shear is applied, the layer shear thickens due to the PS chains extended to nearly twice their original lengths

  13. Filter-adsorber aging assessment

    Energy Technology Data Exchange (ETDEWEB)

    Winegardner, W.K. [Pacific Northwest Laboratory, Richland, WA (United States)

    1995-02-01

    An aging assessment of high-efficiency particulate (HEPA) air filters and activated carbon gas adsorption units was performed by the Pacific Northwest Laboratory as part of the U.S. Nuclear Regulatory Commission`s (USNRC) Nuclear Plant Aging Research (NPAR) Program. This evaluation of the general process in which characteristics of these two components gradually change with time or use included the compilation of information concerning failure experience, stressors, aging mechanisms and effects, and inspection, surveillance, and monitoring methods (ISMM). Stressors, the agents or stimuli that can produce aging degradation, include heat, radiation, volatile contaminants, and even normal concentrations of aerosol particles and gasses. In an experimental evaluation of degradation in terms of the tensile breaking strength of aged filter media specimens, over forty percent of the samples did not meet specifications for new material. Chemical and physical reactions can gradually embrittle sealants and gaskets as well as filter media. Mechanisms that can lead to impaired adsorber performance are associated with the loss of potentially available active sites as a result of the exposure of the carbon to airborne moisture or volatile organic compounds. Inspection, surveillance, and monitoring methods have been established to observe filter pressure drop buildup, check HEPA filters and adsorbers for bypass, and determine the retention effectiveness of aged carbon. These evaluations of installed filters do not reveal degradation in terms of reduced media strength but that under normal conditions aged media can continue to effectively retain particles. However, this degradation may be important when considering the likelihood of moisture, steam, and higher particle loadings during severe accidents and the fact it is probable that the filters have been in use for an extended period.

  14. Ecological applications of the irradiated adsorbents

    International Nuclear Information System (INIS)

    Tusseyev, T.

    2004-01-01

    Full text: In our previous works it was shown that after irradiation some adsorbents gain new interesting properties such as increasing (or decreasing) of their adsorption capacity, selectivity in relation to some gases, change of chemical bounds of gas molecules with adsorbent surface as well as other properties. We investigated a lot of adsorbents with semiconducting and dielectric properties. A high temperature superconductor was investigated also. Adsorbents were irradiated by ultraviolet (UV) and gamma - radiation, reactor (n.γ) - radiation, α-particles (E=40-50 MeV), protons ( E=30 MeV), and also He-3 ions (E-29-60 MeV). The following techniques were used: volumetric (manometrical), mass-spectrometer and IR spectroscopic methods, and also method of electronic - paramagnetic resonance (spin paramagnetic resonance) The obtained results allow to speak about creation of new adsorbents for gas purification (clearing) from harmful impurities, gas selection into components, an increasing of adsorbing surface. Thus one more advantage of the irradiated adsorbents is that they have 'memory effect', i.e. they can be used enough long time after irradiation. In laboratory conditions we built the small-sized adsorptive pump on the basis of the irradiated zeolites which are capable to work in autonomous conditions. It was found, that some of adsorbents after irradiation gain (or lose) selectivity in relation to definite gases. So, silica gel, which one in initial state does not adsorb hydrogen, after gamma irradiation it becomes active in relation to hydrogen. Some of rare earths oxides also show selectivity in relation to hydrogen and oxygen depending on a type of irradiation. Thus, it is possible to create different absorbents, depending on a solved problem, using a way or selection of adsorbents, either of radiation type and energy, as a result obtained adsorbents can be used for various ecological purposes

  15. An in-situ RBS system for measuring nuclides adsorbed at the liquid-solid interface

    Energy Technology Data Exchange (ETDEWEB)

    Morita, K.; Yuhara, J.; Ishigami, R. [Nagoya Univ. (Japan). School of Engineering] [and others

    1997-03-01

    An in-situ RBS system has been developed in which heavier nuclides adsorbed at the inner surface of a thin lighter window specimen of liquid container in order to determine the rate constants for their sorption and release at the interface. The testing of a thin silicon window of the sample assembly, in which Xe gas of one atmosphere was enclosed, against the bombardment of the probing ion beam has been performed. A desorption behavior of a lead layer adsorbed at the SiO{sub 2} layer of silicon window surface into deionized water has been measured as a preliminary experiment. (author)

  16. Complete braided adsorbent for marine testing to demonstrate 3g-U/kg-adsorbent

    Energy Technology Data Exchange (ETDEWEB)

    Janke, Chris [ORNL; Yatsandra, Oyola [ORNL; Mayes, Richard [ORNL; none,; Gill, Gary [PNNL; Li-Jung, Kuo [PNNL; Wood, Jordana [PNNL; Sadananda, Das [ORNL

    2014-04-30

    ORNL has manufactured four braided adsorbents that successfully demonstrated uranium adsorption capacities ranging from 3.0-3.6 g-U/kg-adsorbent in marine testing at PNNL. Four new braided and leno woven fabric adsorbents have also been prepared by ORNL and are currently undergoing marine testing at PNNL.

  17. Retention of radium from thermal waters on sand filters and adsorbents

    Energy Technology Data Exchange (ETDEWEB)

    Elejalde, C. [Dpto. de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria, Alameda de Urquijo s/n, 48013 Bilbao (Spain)]. E-mail: inpelsac@bi.ehu.es; Herranz, M. [Dpto. de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria, Alameda de Urquijo s/n, 48013 Bilbao (Spain); Idoeta, R. [Dpto. de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria, Alameda de Urquijo s/n, 48013 Bilbao (Spain); Legarda, F. [Dpto. de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria, Alameda de Urquijo s/n, 48013 Bilbao (Spain); Romero, F. [Dpto. de Ingenieria Quimica y del Medio Ambiente, Escuela Tecnica Superior de Ingenieria, Alameda de Urquijo s/n, 48013 Bilbao (Spain); Baeza, A. [Dpto. de Fisica, Facultad de Veterinaria, Universidad de Extremadura, Avda. Universidad s/n, 10071 Caceres (Spain)

    2007-06-18

    This study was focussed on laboratory experiences of retention of radium from one thermal water on sand filters and adsorbents, trying to find an easy method for the elimination in drinkable waters polluted with this natural radio-nuclide. A thermal water from Cantabria (Spain) was selected for this work. Retention experiences were made with columns of 35 mm of diameter containing 15 cm layers of washed river sand or 4 cm layers of zeolite A3, passing known volumes of thermal water at flows between 4 and 40 ml/min with control of the retained radium by determining the amount in the water after the treatment. The statistical analysis of data suggests that retention depends on the flow and the volume passed through the columns. As additional adsorbents were used kaolin and a clay rich in illite. Jar-test experiences were made agitating known weights of adsorbents with the selected thermal water, with addition of flocculants and determination of radium in filtrated water after the treatment. Data suggest that retention is related to the weight of adsorbent used, but important quantities of radium seem remain in solution for higher amounts of adsorbents, according to the statistical treatment of data. The elution of retained radium from columns or adsorbents, previously used in experiences, should be the aim of a future research.

  18. Retention of radium from thermal waters on sand filters and adsorbents

    International Nuclear Information System (INIS)

    Elejalde, C.; Herranz, M.; Idoeta, R.; Legarda, F.; Romero, F.; Baeza, A.

    2007-01-01

    This study was focussed on laboratory experiences of retention of radium from one thermal water on sand filters and adsorbents, trying to find an easy method for the elimination in drinkable waters polluted with this natural radio-nuclide. A thermal water from Cantabria (Spain) was selected for this work. Retention experiences were made with columns of 35 mm of diameter containing 15 cm layers of washed river sand or 4 cm layers of zeolite A3, passing known volumes of thermal water at flows between 4 and 40 ml/min with control of the retained radium by determining the amount in the water after the treatment. The statistical analysis of data suggests that retention depends on the flow and the volume passed through the columns. As additional adsorbents were used kaolin and a clay rich in illite. Jar-test experiences were made agitating known weights of adsorbents with the selected thermal water, with addition of flocculants and determination of radium in filtrated water after the treatment. Data suggest that retention is related to the weight of adsorbent used, but important quantities of radium seem remain in solution for higher amounts of adsorbents, according to the statistical treatment of data. The elution of retained radium from columns or adsorbents, previously used in experiences, should be the aim of a future research

  19. Polyethylenimine surface layer for enhanced virus immobilization on cellulose

    Science.gov (United States)

    Tiliket, Ghania; Ladam, Guy; Nguyen, Quang Trong; Lebrun, Laurent

    2016-05-01

    Thin regenerated cellulose films are prepared by hydrolysis of cellulose acetate (CA). A polycation, namely polyethylenimine (PEI), is then adsorbed onto the films. From QCM-D analysis, PEI readily adsorbs from a 0.1% w/v solution in NaCl 0.2 M (ca. 100 ng cm-2). Further PEI adsorption steps at higher PEI concentrations induce a linear growth of the PEI films, suggesting that free adsorption sites still exist after the initial adsorption. The adsorbed PEI chains are resistant to variations of the ionic strength up to NaCl 1 M. Promisingly, the adsorption of T4D bacteriophages are 15-fold more efficient onto the PEI-treated, compared to the native regenerated cellulose films, as measured by QCM-D. This confirms the strong affinity between the negatively charged viruses and PEI, even at low PEI concentration, probably governed by strong electrostatic attractive interactions. This result explains the remarkable improvement of the affinity of medical masks for virus droplets when one of their cellulose layers was changed by two-PEI-functionalized cellulose-based filters.

  20. adsorbent for defluoridation of drinking water

    African Journals Online (AJOL)

    2014-12-17

    Dec 17, 2014 ... In this study, the performance of different aluminium hydroxide–based adsorbents was compared in terms of fluoride adsorption capacity, potential for repetitive regeneration, surface acidity and surface site concentrations. The adsorbents were aluminium hydro(oxide) (AO), activated alumina (AA), and ...

  1. Extraction of uranium from seawater by the fibrous composite adsorbent

    International Nuclear Information System (INIS)

    Katoh, Shunsaku; Sugasaka, Kazuhiko; Nogi, Tatsuo; Yoshizumi, Nobuo; Mima, Kooji.

    1986-01-01

    The fibrous composite adsorbents consisting of hydrous titanium oxide and activated carbon were prepared with hydrophilic polyacrylonitrile system polymer as a binder under various conditions, and the adsorptive property of the fibrous composite adsorbents for uranium from seawater was examined. The fibrous composite adsorbents which spun under high pressure (10 kg/cm 2 ) was the finest having the largest pore volume. In addition, the amount of uranium adsorbed of the fibrous adsorbent was the largest. The rate of uranium adsorption by the fibrous adsorbent was the same as the rate of uranium adsorption by the powdery adsorbent. The excellent fibrous adsorbent adsorbed 0.23 mg U/g adsorbent for 10 d and 0.65 mg U/g adsorbent for 100 d. The rate of uranium desorption from the fibrous adsorbent by alkali carbonate solution was large, and the uranium in the fibrous adsorbent desorbed 75 % for 8 h and about 100 % for 24 h. (author)

  2. An innovative zinc oxide-coated zeolite adsorbent for removal of humic acid

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Lingling, E-mail: lasier_wang@hotmail.com [College of Chemical Engineering and Materials, Quanzhou Normal University, Quanzhou 362000, Fujian (China); Environmental Engineering and Science Program, 705 Engineering Research Center, University of Cincinnati, Cincinnati, OH 45221-0012 (United States); Han, Changseok [ORISE Post-doctoral Fellow, The U.S. Environmental Protection Agency, ORD, NRMRL, STD, CPB, 26 W. Martin Luther King Jr. Drive, Cincinnati, OH 45268 (United States); Nadagouda, Mallikarjuna N. [The U.S. Environmental Protection Agency, ORD, NRMRL, WSWRD, WQMB, 26 W. Martin Luther King Jr. Drive, Cincinnati, OH 45268 (United States); Dionysiou, Dionysios D., E-mail: dionysios.d.dionysiou@uc.edu [Environmental Engineering and Science Program, 705 Engineering Research Center, University of Cincinnati, Cincinnati, OH 45221-0012 (United States); Nireas-International Water Research Centre, School of Engineering, University of Cyprus, PO Box 20537, 1678, Nicosia (Cyprus)

    2016-08-05

    Highlights: • An innovative adsorbent was successfully synthesized to remove humic acid. • The adsorbent possessed high adsorption capacity for humic acid. • The adsorption capacity remarkably increased after an acid modification. • The adsorption capacity was proportional to the amount of ZnO coated on zeolite. • Electrostatic interactions are a major factor at the first stage of the process. - Abstract: Zinc oxide (ZnO)-coated zeolite adsorbents were developed by both nitric acid modification and Zn(NO{sub 3}){sub 2}·6H{sub 2}O functionalization of zeolite 4A. The developed adsorbents were used for the removal of humic acid (HA) from aqueous solutions. The synthesized materials were characterized by porosimetry analysis, scanning electron microscopy, X-Ray diffraction analysis, and high resolution transmission electron microscopy. The maximum adsorption capacity of the adsorbents at 21 ± 1 °C was about 60 mgC g{sup −1}. The results showed that the positive charge density of ZnO-coated zeolite adsorbents was proportional to the amount of ZnO coated on zeolite and thus, ZnO-coated zeolite adsorbents exhibited a greater affinity for negatively charged ions. Furthermore, the adsorption capacity of ZnO-coated zeolite adsorbents increased markedly after acid modification. Adsorption experiments demonstrated ZnO-coated zeolite adsorbents possessed high adsorption capacity to remove HA from aqueous solutions mainly due to strong electrostatic interactions between negative functional groups of HA and the positive charges of ZnO-coated zeolite adsorbents.

  3. Adsorbed Polymer Nanolayers on Solids: Mechanism, Structure and Applications

    Science.gov (United States)

    Sen, Mani Kuntal

    In this thesis, by combining various advanced x-ray scattering, spectroscopic and other surface sensitive characterization techniques, I report the equilibrium polymer chain conformations, structures, dynamics and properties of polymeric materials at the solid-polymer melt interfaces. Following the introduction, in chapter 2, I highlight that the backbone chains (constituted of CH and CH2 groups) of the flattened polystyrene (PS) chains preferentially orient normal to the weakly interactive substrate surface via thermal annealing regardless of the initial chain conformations, while the orientation of the phenyl rings becomes randomized, thereby increasing the number of surface-segmental contacts (i.e., enthalpic gain) which is the driving force for the flattening process of the polymer chains even onto a weakly interactive solid. In chapter 3, I elucidate the flattened structures in block copolymer (BCP) thin films where both blocks lie flat on the substrate, forming a 2D randomly phase-separated structure irrespective of their microdomain structures and interfacial energetics. In chapter 4, I reveal the presence of an irreversibly adsorbed BCP layer which showed suppressed dynamics even at temperatures far above the individual glass transition temperatures of the blocks. Furthermore, this adsorbed BCP layer plays a crucial role in controlling the microdomain orientation in the entire film. In chapter 5, I report a radically new paradigm of designing a polymeric coating layer of a few nanometers thick ("polymer nanolayer") with anti-biofouling properties.

  4. Modeling diffusion of adsorbed polymer with explicit solvent.

    Science.gov (United States)

    Desai, Tapan G; Keblinski, Pawel; Kumar, Sanat K; Granick, Steve

    2007-05-25

    Computer simulations of a polymer chain of length N strongly adsorbed at the solid-liquid interface in the presence of explicit solvent are used to delineate the factors affecting the N dependence of the polymer lateral diffusion coefficient, D(||). We find that surface roughness has a large influence, and D(||) scales as D(||) approximately N(-x), with x approximately 3/4 and x approximately 1 for ideal smooth and corrugated surfaces, respectively. The first result is consistent with the hydrodynamics of a "particle" of radius of gyration R(G) approximately N(nu) (nu=0.75) translating parallel to a planar interface, while the second implies that the friction of the adsorbed chains dominates. These results are discussed in the context of recent measurements.

  5. Thermal effects of CO2 capture by solid adsorbents: some approaches by IR image processing

    International Nuclear Information System (INIS)

    Benevides Ferreira, J.F.; Pradere, C.; Batsale, J.C.; Jolly, J.; Pavageau, B.; Le Bourdon, G.; Mascetti, J.; Servant, L.

    2013-01-01

    Thanks to infrared thermography, we have studied the mechanisms of CO 2 capture by solid adsorbents (CO 2 capture via gas adsorption on various types of porous substrates) to better understand the physico-chemical mechanisms that control CO 2 -surface interactions. In order to develop in the future an efficient process for post-combustion CO 2 capture, it is necessary to quantify the energy of adsorption of the gas on the adsorbent (exothermic process). The released heat (heat of adsorption) is a key parameter for the choice of materials and for the design of capture processes. Infrared thermography is used, at first approach, to detect the temperature fields on a thin-layer of adsorbent during CO 2 adsorption. An analytical heat transfer model was developed to evaluate the adsorption heat flux and to estimate, via an inverse technique, the heat of adsorption. The main originality of our method is to estimate heat losses directly from the heat generated during the adsorption process. Then, the estimated heat loss is taken for an a posteriori calculation of the adsorption heat flux. Finally, the heat of adsorption may be estimated. The interest in using infrared thermography is also its ability to quickly change the experimental setup, for example, to switch from the adsorbent thin-layer to the adsorbent bed configuration. We present the first results tempting to link the thin-layer data to the propagation speed of the thermal front in a milli-fluidics adsorption bed, also observed by IR thermography. (authors)

  6. Environmentally Friendly in Situ Regeneration of Graphene Aerogel as a Model Conductive Adsorbent.

    Science.gov (United States)

    Pan, Meilan; Shan, Chao; Zhang, Xiaolin; Zhang, Yanyang; Zhu, Chanyuan; Gao, Guandao; Pan, Bingcai

    2018-01-16

    Adsorption is a classical process widely used in industry and environmental protection, and the regeneration of exhausted adsorbents, as the reverse process of adsorption, is vital to achieving a sustainable adsorption process. Chemical and thermal regeneration, which feature high costs and environmental side effects, are classical but not environmentally friendly methods. Herein, a new regeneration method based on an electrochemical process using graphene aerogel (GA) as a model conductive adsorbent was proposed. First, 3D GA was prepared to adsorb organic and inorganic pollutants, avoiding the inconvenience of using powdered graphene. Then, the exhausted GA was cleaned by the electrochemical desorption and degradation of adsorbed organic pollutants if undesired and the electrorepulsion of adsorbed metal ions in the absence of any additional chemicals, showing a high processing capability of 1.21 L g -1 GA h -1 and low energy consumption (∼0.2 kWh m -3 solution). The mechanisms involved in the electrochemistry-induced desorption process cover a decline in the GA adsorption performance depended on the electrochemically adjustable surface charge conditions, and the further repulsion and migration of adsorbates is subject to the strong in situ electric field. This work has important implications for the development of environmentally friendly regeneration processes and qualified adsorbents as well as the application of a green and efficient regeneration concept for traditional adsorption processes.

  7. Molecular structure and Equilibrium forces of bovine submaxillary mucin adsorbed at a solid-liquid interface

    DEFF Research Database (Denmark)

    Zappone, Bruno; Patil, Navinkumar J.; Madsen, Jan Busk

    2015-01-01

    By combining dynamic light scattering, circular dichroism spectroscopy, atomic force microscopy, and surface force apparatus, the conformation of bovine submaxillary mucin in dilute solution and nanomechanical properties of mucin layers adsorbed on mica have been investigated. The samples were......-ranged, repulsive, and nonhysteretic forces upon compression of the adsorbed layers. Detailed analysis of such forces suggests that adsorbed mucins had an elongated conformation favored by the stiffness of the central domain. Acidification of aqueous media was chosen as means to reduce mucin−mucin and mucin......−substrate electrostatic interactions. The hydrodynamic diameter in solution did not significantly change when the pH was lowered, showing that the large persistence length of the mucin molecule is due to steric hindrance between sugar chains, rather than electrostatic interactions. Remarkably, the force generated...

  8. A heat transfer correlation for transient vapor uptake of powdered adsorbent embedded onto the fins of heat exchangers

    KAUST Repository

    Li, Ang

    2015-10-23

    We present a detailed study on the transient heat transfer phenomena of powdered-adsorbent mixed with an organic binder for adherence to the fins of a heat exchangers. The transient performance of such an adsorbent-heat exchanger configuration has significant application potential in the adsorption desalination plants and chillers but seldom addressed in the literature. An experiment is designed to measure the heat transfer for several adsorption temperatures under a single vapor component environment. Analysis on the experimental data indicates that the adsorbent-adsorbate interactions contribute about 75% of the total thermal resistances throughout the uptake processes. It is found that the initial local adsorption heat transfer coefficients are significantly higher than the average values due primarily to the thermal mass effect of the adsorbent–adsorbate interaction layers. From these experiments, a correlation for the transient local adsorption heat transfer coefficients is presented at the sub-atmospheric pressures and assorted application temperatures.

  9. Electronically driven adsorbate excitation mechanism in femtosecond-pulse laser desorption

    DEFF Research Database (Denmark)

    Brandbyge, Mads; Hedegård, Per; Heinz, T. F.

    1995-01-01

    a systematic theoretical treatment of this coupling process in the language of an electronic friction, which generates Langevin noise in the adsorbate center-of-mass degrees of freedom, while the electronic degrees of freedom are at a high temperature. Starting from an influence-functional path......-integral description, a simple formula for the electronic friction is defined which is valid at all electronic temperatures. At low temperatures the formalism makes contact with the electronic friction appearing in the theory of adsorbate vibrational damping, whereas at high temperatures comparable with the adsorbate...... electronic excitation energies the friction becomes strongly temperature dependent due to dominance by virtual excitations between different adsorbate potential energy surfaces. The former regime is related to the electronic friction model for the desorption process, and the latter to the desorption induced...

  10. Adsorbate-induced lifting of substrate relaxation is a general mechanism governing titania surface chemistry.

    Science.gov (United States)

    Silber, David; Kowalski, Piotr M; Traeger, Franziska; Buchholz, Maria; Bebensee, Fabian; Meyer, Bernd; Wöll, Christof

    2016-09-30

    Under ambient conditions, almost all metals are coated by an oxide. These coatings, the result of a chemical reaction, are not passive. Many of them bind, activate and modify adsorbed molecules, processes that are exploited, for example, in heterogeneous catalysis and photochemistry. Here we report an effect of general importance that governs the bonding, structure formation and dissociation of molecules on oxidic substrates. For a specific example, methanol adsorbed on the rutile TiO 2 (110) single crystal surface, we demonstrate by using a combination of experimental and theoretical techniques that strongly bonding adsorbates can lift surface relaxations beyond their adsorption site, which leads to a significant substrate-mediated interaction between adsorbates. The result is a complex superstructure consisting of pairs of methanol molecules and unoccupied adsorption sites. Infrared spectroscopy reveals that the paired methanol molecules remain intact and do not deprotonate on the defect-free terraces of the rutile TiO 2 (110) surface.

  11. CD spectroscopy of proteins adsorbed at flat hydrophilic quartz and hydrophobic Teflon surfaces

    NARCIS (Netherlands)

    Vermeer, AWP; Norde, W

    2000-01-01

    Spectroscopic methods provide a powerful tool for studying the properties of proteins at interfaces. The protein accumulated in one adsorbed layer is frequently less than the minimum mass of protein required by a detection method. In such a case las is the case in circular dichroism spectroscopy)

  12. Controlling the magnetism of adsorbed metal-organic molecules.

    Science.gov (United States)

    Kuch, Wolfgang; Bernien, Matthias

    2017-01-18

    Gaining control on the size or the direction of the magnetic moment of adsorbed metal-organic molecules constitutes an important step towards the realization of a surface-mounted molecular spin electronics. Such control can be gained by taking advantage of interactions of the molecule's magnetic moment with the environment. The paramagnetic moments of adsorbed metal-organic molecules, for example, can be controlled by the interaction with magnetically ordered substrates. Metalloporphyrins and -phthalocyanines display a quasi-planar geometry, allowing the central metal ion to interact with substrate electronic states. This can lead to magnetic coupling with a ferromagnetic or even antiferromagnetic substrate. The molecule-substrate coupling can be mediated and controlled by insertion layers such as oxygen atoms, graphene, or nonmagnetic metal layers. Control on the magnetic properties of adsorbed metalloporphyrins or -phthalocyanines can also be gained by on-surface chemical modification of the molecules. The magnetic moment or the magnetic coupling to ferromagnetic substrates can be changed by adsorption and thermal desorption of small molecules that interact with the fourfold-coordinated metal center via the remaining axial coordination site. Spin-crossover molecules, which possess a metastable spin state that can be switched by external stimuli such as temperature or light, are another promising class of candidates for control of magnetic properties. However, the immobilization of such molecules on a solid surface often results in a quench of the spin transition due to the interaction with the substrate. We present examples of Fe(II) spin-crossover complexes in direct contact with a solid surface that undergo a reversible spin-crossover transition as a function of temperature, by illumination with visible light, or can be switched by the tip of a scanning tunneling microscope.

  13. Alkali metal adsorbate sputtering by molecular impact

    International Nuclear Information System (INIS)

    Moran, J.P.; Wachman, H.Y.; Trilling, L.

    1974-01-01

    An exploratory study of the sputtering by a krypton molecular beam of rubidium adsorbed at low coverage on a tungsten substrate has been described in a previous paper. An extension of this work is reported now

  14. Black Sprayable Molecular Adsorber Coating Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The main objective of this technology project is to develop, optimize, and flight qualify a black version of the molecular adsorber coating and a conductive version...

  15. PERVAPORATION USING ADSORBENT-FILLED MEMBRANES

    Science.gov (United States)

    Membranes containing selective fillers, such as zeolites and activated carbon, can improve the separation by pervaporation. Applications of adsorbent-filled membranes in pervaporation have been demonstrated by a number of studies. These applications include removal of organic co...

  16. New liquid waste control with tannin adsorbent

    International Nuclear Information System (INIS)

    Nakamura, Yoshinobu; Shirato, Wataru; Nakamura, Yasuo

    1998-01-01

    Since 1971, the Mitsubishi Nuclear Fuel Co., Ltd. (MNF) has been fabricating PWR fuels and developing related technology and processes. In the UF 6 reconversion lines of MNF, the ammonium diuranate (ADU) process has been operating and the newly developed process of liquid waste treatment was installed last year. The characteristic of this process is to use insoluble tannin adsorbent which has been developed by MNF. The tannin adsorbent is not only an effective means to adsorb heavy metals such as uranium and plutonium but is also easy to incinerate at low temperature. Control of radioactive liquid waste from nuclear facilities is generally implemented by co-precipitation. However, it produces secondary wastes such as noncombustible materials which include radionuclides and it is anticipated that the storage and disposal of those wastes will be at high cost. Those are the reasons why tannin adsorbent has an advantage, and why MNF develops it. (author)

  17. NOx Removal and Effect of Adsorbate-Adsorbate Interactions

    DEFF Research Database (Denmark)

    Khan, Tuhin Suvra

    to obtain more accurate catalytic rates than with the commonly used non-interacting mean field model. I then applied the proposed adsorbate-adsorbate interaction model to three important catalytic reactions, the direct NO decomposition, CO methanation, and steam reforming of methane, and analyzed the effect...... these challenges systematically and have developed some new methods and models to counter those challenges and obtain some general understanding of the catalytic process. I have developed an adsorbate-adsorbate interaction model to include the coverage dependency of the adsorption energy in kinetic models...... of adsorbate-adsorbate interactions on their catalytic rates. An alloy screening method has also been developed to screen for the industrially most promising alloy catalysts for any catalytic reaction. I have also studied the structure sensitivity of the rates of catalytic direct NO decomposition on different...

  18. Dissolved Air Flotation of arsenic adsorbent particles

    Directory of Open Access Journals (Sweden)

    Mario Enrique Santander Muñoz

    2015-01-01

    Full Text Available The removal of arsenic from synthetic effluent was studied using the adsorbent particle flotation technique (APF and dissolved air flotation (DAF. A sample of an iron mineral was used as adsorbent particles of arsenic, ferric chloride as coagulant, cationic poly-acrylamide (NALCO 9808 as flocculants, and sodium oleate as collector. Adsorption studies to determine the pH influence, contact time, and adsorbent particles concentration on the adsorption of arsenic were carried out along with flotation studies to determine the removal efficiency of adsorbents particles. The results achieved indicate that the adsorption kinetic of arsenic is very rapid and that in range of pH’s from 2 to 7 the adsorption percentages remain constant. The equilibrium conditions were achieved in 60 minutes and about 95% of arsenic was adsorbed when used an adsorbent concentration of 2 g/L and pH 6.3. The maximum adsorption capacity of adsorbent particles was 4.96 mg/g. The mean free energy of adsorption (E was found to be 2.63 kJ/mol, which suggests physisorption. The results of the flotation studies demonstrated that when synthetic effluents with 8.9 mg/L of arsenic were treated under the following experimental conditions; 2 g/L of adsorbent particles, 120 mg/L of Fe(III, 2 mg/L of Nalco 9808, 20 mg/L of sodium oleate, and 40% of recycle ratio in the DAF, it was possible to reach 98% of arsenic removal and 6.3 NTU of residual turbidity in clarified synthetic effluent.

  19. Mesoporous Silica: A Suitable Adsorbent for Amines

    Directory of Open Access Journals (Sweden)

    Abdollahzadeh-Ghom Sara

    2009-01-01

    Full Text Available Abstract Mesoporous silica with KIT-6 structure was investigated as a preconcentrating material in chromatographic systems for ammonia and trimethylamine. Its adsorption capacity was compared to that of existing commercial materials, showing its increased adsorption power. In addition, KIT-6 mesoporous silica efficiently adsorbs both gases, while none of the employed commercial adsorbents did. This means that KIT-6 Mesoporous silica may be a good choice for integrated chromatography/gas sensing micro-devices.

  20. Adsorbate Diffusion on Transition Metal Nanoparticles

    Science.gov (United States)

    2015-01-01

    systematically studied adsorption and diffusion of atomic and diatomic species (H, C, N, O, CO, and NO) on nanometer-sized Pt and Cu nanoparticles with...species and two diatomic molecules (H, C, N, O, CO, and NO) as adsorbates and study the adsorption and diffusion of these adsorbates across the edges...DOE-BES, Division of Chemical Sciences (grant DE-FG02-05ER15731), and by the Air Force Office of Scientific Research under a Basic Research Initiative

  1. Thermally robust chelating adsorbents for the capture of gaseous mercury: Fixed-bed behavior

    Energy Technology Data Exchange (ETDEWEB)

    Ji, L.; Abu-Daabes, M.; Pinto, N.G. [University of Cincinnati, Cincinnati, OH (USA). Dept. of Chemical and Material Engineering

    2009-02-15

    Thermally robust chelating adsorbents for the capture of vapor-phase mercuric chloride (HgCl2) have been developed, to address the issue of mercury removal from flue gases from coal-fired power plants. The adsorbents are mesoporous silica substrates functionalized with a chelating agent and coated with an ionizing surface nano-layer. This architecture enables selective, multi-dentate adsorption of mercury directly from the gas phase with high capacity. The capture efficiency of the adsorbents was evaluated in the fixed-bed mode for oxidized mercury at 160{sup o}C. Two chelating adsorbents, one functionalized with 3-mercaptopropyltrimethoxysilane (MPTS) and the other with 2-mercaptobenzothialzole (MBT), were studied. For both adsorbents a high mercury uptake capacity was observed, several times higher than that of commercial activated carbon. The mechanism for mercury uptake in the two adsorbents is different. The effect of pore size on uptake was also evaluated. It was found that pore size does not have a significant effect on the mercury adsorption, and mercury diffusion through the ionic coating is believed to be the rate-limiting step for capture.

  2. POTENTIAL USE OF WOOL WASTE AS ADSORBENT FOR THE REMOVAL OF ACID DYES FROM WASTEWATER

    Directory of Open Access Journals (Sweden)

    BUCIŞCANU Ingrid

    2016-05-01

    Full Text Available At present, great amounts of raw wool are treated as waste and raise disposal problems. In the sustainable development context , wool is regarded as a biodegradable renewable resource and due to its complex chemical composition and fiber morphology, can find different useful applications. It is the aim of this paper to investigate the potential use of raw wool waste as a non-conventional adsorbent for Acid Red 337(AcR ,currently used for leather and wool dyeing. Two wool-based adsorbents were prepared, namely scoured coarse wool (Wool-S and wool activated with alcoholic solution of sodium hydroxide (Wool-A. Adsorbent dosage, dye concentration, pH and treatment time were factors taken in consideration for the assessment of the sorbate-adsorbent interaction. The removal efficiency (R % is mainly dependent on the solution pH and on the activation treatment applied to wool: at pH 3, the removal efficiency reaches the highest values of 42% on Wool-S and 99% on Wool-A. The adsorption rate is slow and needs almost 6 h to reach equilibrium. The experimental data best fitted the Langmuir equilibrium adsorption model, which proves that the adsorbent possess surface active sites to which the dye sorbate binds in monomolecular layer. Raw wool waste is a potential cheap, biodegradable and effective adsorbent for colored wastewater treatment.

  3. Negative chromatography of hepatitis B virus-like particle: Comparative study of different adsorbent designs.

    Science.gov (United States)

    Lee, Micky Fu Xiang; Chan, Eng Seng; Tan, Wen Siang; Tam, Kam Chiu; Tey, Beng Ti

    2016-05-06

    Purification of virus-like particles (VLPs) in bind-and-elute mode has reached a bottleneck. Negative chromatography has emerged as the alternative solution; however, benchmark of negative chromatography media and their respective optimized conditions are absent. Hence, this study was carried out to compare the performance of different negative chromatography media for the purification of hepatitis B VLPs (HB-VLPs) from clarified Escherichia coli feedstock. The modified anion exchange media, core-shell adsorbents (InertShell and InertLayer 1000) and polymer grafted adsorbents (SQ) were compared. The results of chromatography from packed bed column of core-shell adsorbents showed that there is a trade-off between the purity and recovery of HB-VLPs in the flowthrough fraction due to the shell thickness. Atomic force microscopic analysis revealed funnel-shaped pore channels in the shell layer which may contribute to the entrapment of HB-VLPs. A longer residence time at a lower feed flow rate (0.5ml/min) improved slightly the HB-VLPs purity in all modified adsorbents, but the recovery in InertShell reduced substantially. The preheat-treatment is not recommended for the negative chromatography as the thermal-induced co-aggregation of HCPs and HB-VLPs would flow along with HB-VLPs and thus reduced the HB-VLPs purity in the flowthrough. Further reduction in the feedstock concentration enhanced the purity of HB-VLPs especially in InertLayer 1000 but reduced substantially the recovery of HB-VLPs. In general, the polymer grafted adsorbent, SQ, performed better than the core-shell adsorbents in handling a higher feedstock concentration. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. Measurements of the nuclear spin-spin relaxation times for commensurate {sup 3}He-Ne films adsorbed on hexagonal boron nitride

    Energy Technology Data Exchange (ETDEWEB)

    Parks, C; Sullivan, N S [Department of Physics, University of Florida, Gainesville, FL 32611 (United States); Stachowiak, P [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, PO Box 1410, 50-950 Wroclaw (Poland)], E-mail: Sullivan@phys.ufl.edu

    2009-02-01

    Measurements of the {sup 3}He nuclear spin-spin relaxation time, T{sub 2}, have been carried out for commensurate layers of {sup 3}He-Ne mixtures adsorbed on hexagonal boron nitride for temperatures 0.2< T <10 K. A temperature independent relaxation is observed at low temperatures and is interpreted in terms of the effective exchange frequencies for {sup 3}He particle exchange on the surface. The results show a strong dependence on the fraction of neon in the adsorbed layer. This variation is discussed in terms of a multiple spin exchange model for {sup 3}He in a monolayer. The contributions to T{sub 2} from different components of the exchange, 2-spin exchange (J{sub 2}), 3-spin exchange (J{sub 3}), 4-spin exchange (J{sub 4}) and higher exchange permutations depend on the {sup 3}He coverage and thus permit the separation of the amplitudes of the different exchange rates, and in particular allow one to deduce the relative strengths of 2-atom and 3-atom exchange where other methods are sensitive only to the effective two-particle term J{sub eff} = J{sub 2} - 2J{sub 3}.

  5. Room temperature ferromagnetic and semiconducting properties of graphene adsorbed with cobalt oxide using electrochemical method

    Science.gov (United States)

    Park, Chang-Soo; Lee, Kyung Su; Chu, Dongil; Lee, Juwon; Shon, Yoon; Kim, Eun Kyu

    2017-12-01

    We report the room temperature ferromagnetic properties of graphene adsorbed by cobalt oxide using electrochemical method. The cobalt oxide doping onto graphene was carried out in 0.1 M LiCoO2/DI-water solution. The doped graphene thin film was determined to be a single layer from Raman analysis. The CoO doped graphene has a clear ferromagnetic hysteresis at room temperature and showed a remnant magnetization, 128.2 emu/cm3. The temperature dependent conductivity of the adsorbed graphene showed the semiconducting behavior and a band gap opening of 0.12 eV.

  6. Adsorbed Conformations of PCE Superplasticizers in Cement Pore Solution Unraveled by Molecular Dynamics Simulations.

    Science.gov (United States)

    Hirata, Tsuyoshi; Ye, Jun; Branicio, Paulo; Zheng, Jianwei; Lange, Alex; Plank, Johann; Sullivan, Michael

    2017-11-30

    The conformations of polycarboxylate ether (PCE) type superplasticizer polymers adsorbed on the surface of MgO in cement pore solution are simulated by molecular dynamics (MD). Three types of PCEs commonly applied to concrete are simulated, namely a methacrylate type PCE (PCEM-P), an allyl ether type PCE (PCEA-P), and an isoprenyl ether type PCE (PCEI-P) with ethylene oxide (EO) unit numbers (P) of 25, 34 and 25, respectively. It is observed that the adsorbed layer thickness is inversely proportional to the experimentally measured adsorbed amount at the initial paste flow of 26 ± 0.5 cm. Simulation results indicate that the adsorbed layer thickness is sensitive to the initial polymer orientations against the model MgO surface. I.e., polymer molecules initially placed parallel/perpendicularly against the MgO surface gradually forms a train shaped or a loop and tail adsorption profile, respectively. As a result, the loop and tail shaped conformation gives a higher layer thickness.

  7. Method for modifying trigger level for adsorber regeneration

    Energy Technology Data Exchange (ETDEWEB)

    Ruth, Michael J.; Cunningham, Michael J.

    2010-05-25

    A method for modifying a NO.sub.x adsorber regeneration triggering variable. Engine operating conditions are monitored until the regeneration triggering variable is met. The adsorber is regenerated and the adsorbtion efficiency of the adsorber is subsequently determined. The regeneration triggering variable is modified to correspond with the decline in adsorber efficiency. The adsorber efficiency may be determined using an empirically predetermined set of values or by using a pair of oxygen sensors to determine the oxygen response delay across the sensors.

  8. Adsorbent catalytic nanoparticles and methods of using the same

    Energy Technology Data Exchange (ETDEWEB)

    Slowing, Igor Ivan; Kandel, Kapil

    2017-01-31

    The present invention provides an adsorbent catalytic nanoparticle including a mesoporous silica nanoparticle having at least one adsorbent functional group bound thereto. The adsorbent catalytic nanoparticle also includes at least one catalytic material. In various embodiments, the present invention provides methods of using and making the adsorbent catalytic nanoparticles. In some examples, the adsorbent catalytic nanoparticles can be used to selectively remove fatty acids from feedstocks for biodiesel, and to hydrotreat the separated fatty acids.

  9. Equilibrium and Thermodynamic Studies of Anionic Dyes Removal by an Anionic Clay-Layered Double Hydroxide

    International Nuclear Information System (INIS)

    Kantasamy, N.; Siti Mariam Sumari

    2016-01-01

    Adsorption isotherm describes the interaction of adsorbates with adsorbent in equilibrium. Equilibrium data was examined using Langmuir and Freundlich isotherm models. Thermodynamic studies were used to evaluate the thermodynamic parameters; heat of enthalpy change (ΔH degree), Gibbs free energy change (ΔG degree) and heat of entropy change (ΔSdegree) in order to gain information regarding the nature of adsorption (exothermic or endothermic). Four reactive dyes of anionic type, Acid Blue 29 (AB29), Reactive Black 5 (RB5), Reactive Orange 16 (RO16) and Reactive Red 120 (RR120) were used to obtain equilibrium isotherms at 25, 35, 45 and 55 degree Celsius. Based on Giles' classification, the isotherm produced were of L2-type, indicating strong dye affinity towards the adsorbent, and with weak competition with the solvent molecules for active adsorption sites. Equilibrium data fitted both Langmuir and Freundlich isotherm models with high correlation coefficient (R 2 > 0.91) indicating the possibility of both homogeneity and heterogeneous nature of adsorption. The negative values of ΔGdegree indicate the adsorption processes were spontaneous and feasible. The negative values of ΔHdegree lie between -20 to -75 kJ/ mol, suggesting these processes were exothermic and physical in nature. The negative values of ΔSdegree are indication of decreased disorder and randomness of spontaneous adsorption of reactive dyes on layered double hydroxide as adsorbent. (author)

  10. Protein purification using magnetic adsorbent particles

    DEFF Research Database (Denmark)

    Franzreb, M; Siemann-Herzberg, M.; Hobley, Timothy John

    2006-01-01

    The application of functionalised magnetic adsorbent particles in combination with magnetic separation techniques has received considerable attention in recent years. The magnetically responsive nature of such adsorbent particles permits their selective manipulation and separation in the presence...... of other suspended solids. Thus, it becomes possible to magnetically separate selected target species directly out of crude biological process liquors (e.g. fermentation broths, cell disruptates, plasma, milk, whey and plant extracts) simply by binding them on magnetic adsorbents before application...... of a magnetic field. By using magnetic separation in this way, the several stages of sample pretreatment (especially centrifugation, filtration and membrane separation) that are normally necessary to condition an extract before its application on packed bed chromatography columns, may be eliminated. Magnetic...

  11. Boron removal from wastewater using adsorbents.

    Science.gov (United States)

    Kluczka, J; Trojanowska, J; Zolotajkin, M; Ciba, J; Turek, M; Dydo, P

    2007-01-01

    In the present study, boron adsorption on activated alumina and activated carbon impregnated with calcium chloride, tartaric acid and mannitol was investigated. The adsorbate in question was the wastewater from the chemical landfill in Tarnowskie Gory of 25-70 mg l(-1) boron content. The removal of boron from the above-described wastewater was examined in the static (batch) and dynamic (column) experiments. The static experiments were carried out to assess boron adsorption isotherms, based on which the most efficient adsorbent as well as the rough resin load was determined. On the basis of the dynamic experiment results, the boron adsorptive capacities of the examined resins were deduced. It was concluded that the use of the impregnants increased the ability of activated carbon to adsorb boron. Granulated activated carbon WG-12 impregnated with mannitol was found to be the most promising for the boron removal from wastewater of the Chemical Wastewater Plant in Tarnowskie Gory.

  12. Photoelectron diffraction studies of small adsorbates on single crystal surfaces

    International Nuclear Information System (INIS)

    Pascal, Mathieu

    2002-01-01

    The structural determination of small molecules adsorbed on single crystal surfaces has been investigated using scanned energy mode photoelectron diffraction (PhD). The experimental PhD data were compared to theoretical models using a simulation program based on multiple scattering calculations. Three adsorption systems have been examined on Ag(110), Cu(110) and Cu(111) crystals. The structure of the (2x1)-O adsorption phase on Ag(110) revealed that the O atoms occupied the long bridge site and are almost co-planar with the top layer of Ag atoms. The best agreement between multiple scattering theory and experiment has been obtained for a missing-row (or equivalently an 'added- row') reconstruction. Alternative buckled-row and unreconstructed surface models can be excluded. The adsorption of the benzoate species on Cu(110) has been found to occur via the carboxylate group. The molecules occupy short bridge sites with the O atoms being slightly displaced from atop sites and are aligned along the close-packed azimuth. The tilt of the molecule with respect to the surface and the degree to which the surface is relaxed have also been investigated. The adsorption of methyl on Cu(111) was studied using either azomethane or methyl iodide to prepare the surface layers. At saturation coverage the preferred adsorption site is the fcc threefold hollow site, whereas at half saturation coverage ∼ 30 % of the methyl species occupy the hop threefold hollow sites. Best agreement between theory and experiment corresponded to a methyl group adsorbed with C 3v symmetry. The height of the C above the surface in a pure methyl layer was 1.66 ± 0.02 A, but was reduced to 1.62 ± 0.02 A in the presence of co-adsorbed iodine, suggesting that iodine increases the strength of adsorption. Iodine was also found to occupy the fee threefold hollow sites with a Cu-l bondlength of 2.61 ± 0.02 A. (author)

  13. Investigation on mechanism of phosphate removal on carbonized sludge adsorbent.

    Science.gov (United States)

    Zhang, Lei; Liu, Junxin; Guo, Xuesong

    2018-02-01

    For the removal of phosphate (PO 4 3- ) from water, an adsorbent was prepared via carbonization of sewage sludge from a wastewater treatment plant: carbonized sludge adsorbent (CSA). The mechanism of phosphate removal was determined after studying the structure and chemical properties of the CSA and its influence on phosphate removal. The results demonstrate that phosphate adsorption by the CSA can be fitted with the pseudo second-order kinetics and Langmuir isotherm models, indicating that the adsorption is single molecular layer adsorption dominated by chemical reaction. The active sites binding phosphate on the surface are composed of mineral particles containing Si/Ca/Al/Fe. The mineral containing Ca, calcite, is the main factor responsible for phosphate removal. The phosphate removal mechanism is a complex process including crystallization via the interaction between Ca 2+ and PO 4 3- ; formation of precipitates of Ca 2+ , Al 3+ , and PO 4 3- ; and adsorption of PO 4 3- on some recalcitrant oxides composed of Si/Al/Fe. Copyright © 2017. Published by Elsevier B.V.

  14. Probing molecular adsorbates with core-level spectroscopies: Electronic structure and bonding models

    Science.gov (United States)

    Fohlisch, Alexander

    Resonantly excited X-ray emission spectroscopy has been applied to study the valence electronic structure of molecular adsorbates in an atom specific and orbital symmetry selective manner. In combination with ab initio cluster calculations, electronic structure and bonding models have been derived. Existing models of surface chemical bonding have been reviewed and partially revised. Most notably, the bonding mechanism of carbon monoxide (CO) on transition and noble metals has been revised and is found to be the result of a strong covalent interaction between the CO orbitals and the metal bands within each orbital symmetry. A characteristic allylic configuration is found in the π system and strong polarization within the σ system. The equilibrium properties of adsorbed CO are the direct result of a balance between the repulsive σ-interaction and the attractive π-interaction both in terms of the total energy and the local bond properties. The bonding of ammonia (NH3) on the Cu(110) surface is found to be dominated by a large covalent interaction, which contrasts the previous model of a strong electrostatic interaction. Furthermore, adsorbate-adsorbate interaction leads to a tilted adsorption geometry. Ethylene (C2H4) on Cu(110) is adsorbed in the di-σ configuration, according to the generally accepted Dewar Chatt Duncanson model for hydrocarbon adsorption. The application and interpretation of resonantly excited X-ray emission on these systems also required a thorough discussion of the spectroscopic process. Another topic was the vibrational fine structure in the X-ray photoemission core-level main lines of adsorbed molecules. The observation of the vibrational fine structure in molecular adsorbates is remarkable, as it was previously thought impossible to observe due to solid state broadening contributions. A detailed analysis of the vibrational fine structure and the line profile makes it possible to study the electronic and geometric properties of the core

  15. Tailoring fly ash activated with bentonite as adsorbent for complex wastewater treatment

    Energy Technology Data Exchange (ETDEWEB)

    Visa, Maria, E-mail: maria.visa@unitbv.ro [Transilvania University of Brasov, Department Renewable Energy Systems and Recycling, Eroilor 29, 500036 Brasov (Romania)

    2012-12-15

    Highlights: Black-Right-Pointing-Pointer The spent adsorbent annealed at 500 Degree-Sign C can be a suggestion for padding in stone blocks. Black-Right-Pointing-Pointer The cations can be adsorbent by the silanol group (Si-OH) of the layers from bentonite Black-Right-Pointing-Pointer Copper has a higher affinity for the active sites on adsorbent FAw + B than cadmium. Black-Right-Pointing-Pointer This substrate can be recommended for simultaneous removal of heavy metals and MB. Black-Right-Pointing-Pointer FAw + B is recommended for wastewater treatment resulted in the dyes finishing industry. - Abstract: Used as adsorbent, alkali fly ash represents a low cost solution for advanced wastewater treatment. The alkali treatment raises sustainability issues therefore, in this research we aim to replace alkali fly ash with washed fly ash (FAw). For improving the adsorption capacity of washed fly ash, bentonite powder (B) was added, as a natural adsorbent with a composition almost identical to the fly ash. The new adsorbent was characterized by AFM, XRD, FTIR, SEM, EDS and the surface energy was evaluated by contact angle measurements. For understanding the complex adsorption process on this mixed substrate, preliminary tests were developed on synthetic wastewaters containing a single pollutant system (heavy metal), binary (two-heavy metals) and ternary (dye and two heavy metals) systems. Experiments were done on synthetic wastewaters containing methylene blue, cadmium and copper, using FAw, B and their powder mixtures. The pseudo-second order kinetics could well model all the processes, indicating a good adsorbent material which can be used for the pollutants removal from wastewater. After adsorption the substrates loaded with pollutants, annealed at 500 Degree-Sign C can be reused for padding in stone blocks.

  16. The molecular mechanism of mediation of adsorbed serum proteins to endothelial cells adhesion and growth on biomaterials.

    Science.gov (United States)

    Yang, Dayun; Lü, Xiaoying; Hong, Ying; Xi, Tingfei; Zhang, Deyuan

    2013-07-01

    To explore molecular mechanism of mediation of adsorbed proteins to cell adhesion and growth on biomaterials, this study examined endothelial cell adhesion, morphology and viability on bare and titanium nitride (TiN) coated nickel titanium (NiTi) alloys and chitosan film firstly, and then identified the type and amount of serum proteins adsorbed on the three surfaces by proteomic technology. Subsequently, the mediation role of the identified proteins to cell adhesion and growth was investigated with bioinformatics analyses, and further confirmed by a series of cellular and molecular biological experiments. Results showed that the type and amount of adsorbed serum proteins associated with cell adhesion and growth was obviously higher on the alloys than on the chitosan film, and these proteins mediated endothelial cell adhesion and growth on the alloys via four ways. First, proteins such as adiponectin in the adsorbed protein layer bound with cell surface receptors to generate signal transduction, which activated cell surface integrins through increasing intracellular calcium level. Another way, thrombospondin 1 in the adsorbed protein layer promoted TGF-β signaling pathway activation and enhanced integrins expression. The third, RGD sequence containing proteins such as fibronectin 1, vitronectin and thrombospondin 1 in the adsorbed protein layer bound with activated integrins to activate focal adhesion pathway, increased focal adhesion formation and actin cytoskeleton organization and mediated cell adhesion and spreading. In addition, the activated focal adhesion pathway promoted the expression of cell growth related genes and resulted in cell proliferation. The fourth route, coagulation factor II (F2) and fibronectin 1 in the adsorbed protein layer bound with cell surface F2 receptor and integrin, activated regulation of actin cytoskeleton pathway and regulated actin cytoskeleton organization. Copyright © 2013 Elsevier Ltd. All rights reserved.

  17. Theoretical Insight of Physical Adsorption for a Single Component Adsorbent + Adsorbate System: II. The Henry Region

    KAUST Repository

    Chakraborty, Anutosh

    2009-07-07

    The Henry coefficients of a single component adsorbent + adsorbate system are calculated from experimentally measured adsorption isotherm data, from which the heat of adsorption at zero coverage is evaluated. The first part of the papers relates to the development of thermodynamic property surfaces for a single-component adsorbent + adsorbate system1 (Chakraborty, A.; Saha, B. B.; Ng, K. C.; Koyama, S.; Srinivasan, K. Langmuir 2009, 25, 2204). A thermodynamic framework is presented to capture the relationship between the specific surface area (Ai) and the energy factor, and the surface structural and the surface energy heterogeneity distribution factors are analyzed. Using the outlined approach, the maximum possible amount of adsorbate uptake has been evaluated and compared with experimental data. It is found that the adsorbents with higher specific surface areas tend to possess lower heat of adsorption (ΔH°) at the Henry regime. In this paper, we have established the definitive relation between Ai and ΔH° for (i) carbonaceous materials, metal organic frameworks (MOFs), carbon nanotubes, zeolites + hydrogen, and (ii) activated carbons + methane systems. The proposed theoretical framework of At and AH0 provides valuable guides for researchers in developing advanced porous adsorbents for methane and hydrogen uptake. © 2009 American Chemical Society.

  18. Volatile organic compounds adsorption using different types of adsorbent

    Directory of Open Access Journals (Sweden)

    Pimanmes Chanayotha

    2014-09-01

    Full Text Available Adsorbents were synthesized from coconut shell, coal and coke by pyrolysis followed by chemical activation process. These synthesized materials were used as adsorbents in adsorption test to determine the amount of volatile organic compounds (VOCs namely, 2-Hydroxyethyl methacrylate (HEMA, Octamethylcyclotetrasiloxane and Alkanes standard solution (C8-C20. The adsorption capacities of both synthesized adsorbents and commercial grade adsorbents (Carbotrap™ B and Carbotrap™ C were also compared. It was found that adsorbent A402, which was produced from coconut shell, activated with 40% (wt. potassium hydroxide and at activating temperature of 800°C for 1 hr, could adsorb higher amount of both HEMA and Octamethylcyclotetrasiloxane than other synthesized adsorbents. The maximum adsorption capacity of adsorbent A402 in adsorbing HEMA and Octamethylcyclotetrasiloxane were 77.87% and 50.82% respectively. These adsorption capabilities were 79.73% and 70.07% of the adsorption capacity of the commercial adsorbent Carbotrap™ B respectively. All three types of the synthesized adsorbent (A402, C302, C402 showed the capability to adsorb alkanes standard solution through the range of C8-C20 . However, their adsorption capacities were high in a specific range of C10-C11. The result from the isotherm plot was indicated that surface adsorption of synthesized adsorbent was isotherm type I while the surface adsorption of commercial adsorbent was isotherm type III.

  19. The Structures of Self-Assembled Monolayer Films of Organosulfur Compounds Adsorbed on Gold Single Crystals: Electron Diffraction Studies.

    Science.gov (United States)

    1988-01-01

    AD-M193 125 THE STRUCTURES OF SELF-RSSENSLED MOMOLAYER FILMS OF 1/1 ORGANOSULFUR COMPOUND..(U) HRlYARD UNJY CAMBRIDGE MASS DEPT OF CHEMISTRY L STRONG...VV L- ___ THE STRUCTURES OF SELF-ASSEMBLED MONOLAYER FILMS OF ORGANOSULFUR COMPOUNDS ADSORBED ON GOLD SINGLE CRYSTALS: ELECTRON DIFFRACTION STUDIES...true sulfide phase. V V ’A. LA8700876 REVISED The Structures of Self-Assembled Monolayer Films of Organosulfur Compounds Adsorbed on Gold Single

  20. Impurity screening in strongly coupled plasma systems

    CERN Document Server

    Kyrkos, S

    2003-01-01

    We present an overview of the problem of screening of an impurity in a strongly coupled one-component plasma within the framework of the linear response (LR) theory. We consider 3D, 2D and quasi-2D layered systems. For a strongly coupled plasma the LR can be determined by way of the known S(k) structure functions. In general, an oscillating screening potential with local overscreening and antiscreening regions emerges. In the case of the bilayer, this phenomenon becomes global, as overscreening develops in the layer of the impurity and antiscreening in the adjacent layer. We comment on the limitations of the LR theory in the strong coupling situation.

  1. Application of a site-binding, electrical, double-layer model to nuclear waste disposal

    International Nuclear Information System (INIS)

    Relyea, J.F.; Silva, R.J.

    1981-09-01

    A site-binding, electrical, double-layer adsorption model has been applied to adsorption of Cs for both a montmorillonite clay and powdered SiO 2 . Agreement between experimental and predicted results indicates that C/sub s/ + is adsorbed by a simple cation-exchange mechanism. Further application of a combination equilibrium thermodynamic model and site-binding, electrical, double-layer adsorption model has been made to predict the behavior of U(VI) in solutions contacting either the montmorillonite clay or powdered SiO 2 . Experimentally determined U solution concentrations have been used to select what is felt to be the best available thermodynamic data for U under oxidizing conditions. Given the existing information about the probable U solution species, it was possible to determine that UO 2 +2 is most likely adsorbed by cation-exchange at pH 5. At higher values (pH 7 and 9), it was shown that UO 2 (OH) 2 0 is probably the most strongly adsorbed U solution species. It was also found that high NaCl solution concentrations at higher pH values lowered U concentrations (either because of enhanced sorption or lowered solubility); however, the mechanism responsible for this behavior has not been determined

  2. Formation and composition of adsorbates on hydrophobic carbon surfaces from aqueous laccase-maltodextrin mixture suspension

    Science.gov (United States)

    Corrales Ureña, Yendry Regina; Lisboa-Filho, Paulo Noronha; Szardenings, Michael; Gätjen, Linda; Noeske, Paul-Ludwig Michael; Rischka, Klaus

    2016-11-01

    A robust procedure for the surface bio-functionalization of carbon surfaces was developed. It consists on the modification of carbon materials in contact with an aqueous suspension of the enzyme laccase from Trametes versicolor and the lyophilization agent maltodextrin, with the pH value adjusted close to the isoelectric point of the enzyme. We report in-situ investigations applying Quartz Crystal Microbalance with Dissipation (QCM-D) for carbon-coated sensor surfaces and, moreover, ex-situ measurements with static contact angle measurements, X-ray Photoelectron Spectroscopy (XPS) and Scanning Force Microscopy (SFM) for smooth Highly Oriented Pyrolytic Graphite (HOPG) substrates, for contact times between the enzyme formulation and the carbon material surface ranging from 20 s to 24 h. QCM-D studies reveals the formation of rigid layer of biomaterial, a few nanometers thin, which shows a strongly improved wettability of the substrate surface upon contact angle measurements. Following spectroscopic characterization, these layers are composed of mixtures of laccase and maltodextrin. The formation of these adsorbates is attributed to attractive interactions between laccase, the maltodextrin-based lyophilization agent and the hydrophobic carbon surfaces; a short-term contact between the aqueous laccase mixture suspension and HOPG surfaces is shown to merely result in de-wetting patterns influencing the results of contact angle measurements. The new enzyme-based surface modification of carbon-based materials is suggested to be applicable for the improvement of not only the wettability of low energy substrate surfaces with fluid formulations like coatings or adhesives, but also their adhesion in contact with hardened polymers.

  3. Magnetically supported zeolite adsorbents for effluent treatment

    International Nuclear Information System (INIS)

    Gaydardjiev, S.

    1998-01-01

    An attempt was made to remove heavy metal ions from metallurgical effluents by means of magnetically supported fluidized bed column employing zeolite-magnetite complexes as adsorbents. The natural sorptive properties of acid modified clinoptilolite were used instead of synthetic beads. X-ray diffraction and DTA studies on the raw material confirmed that the main zeolite mineral was clinoptilolite. (author)

  4. Development and characterization of hydrocarbon adsorbent from ...

    African Journals Online (AJOL)

    Raw materials obtained from a local market were used for the production of potential adsorbent. The materials were subjected to preliminary carbonization in a furnace at a controlled temperature in an inert atmosphere and chemical activation was carried out on the carbonized sample. Nylon and used tyre were ...

  5. Water Purification Using Functionalized Cellulosic Fibers with Nonleaching Bacteria Adsorbing Properties.

    Science.gov (United States)

    Ottenhall, Anna; Illergård, Josefin; Ek, Monica

    2017-07-05

    Portable purification systems are easy ways to obtain clean drinking water when there is no large-scale water treatment available. In this study, the potential to purify water using bacteria adsorbing cellulosic fibers, functionalized with polyelectrolytes according to the layer-by-layer method, is investigated. The adsorbed polyelectrolytes create a positive charge on the fiber surface that physically attracts and bonds with bacteria. Three types of cellulosic materials have been modified and tested for the bacterial removal capacity in water. The time, material-water ratio and bacterial concentration dependence, as well as the bacterial removal capacity in water from natural sources, have been evaluated. Freely dispersed bacteria adsorbing cellulosic fibers can remove greater than 99.9% of Escherichia coli from nonturbid water, with the most notable reduction occurring within the first hour. A filtering approach using modified cellulosic fibers is desirable for purification of natural water. An initial filtration test showed that polyelectrolyte multilayer modified cellulosic fibers can remove greater than 99% of bacteria from natural water. The bacteria adsorbing cellulosic fibers do not leach any biocides, and it is an environmentally sustainable and cheap option for disposable water purification devices.

  6. The first step in layer-by-layer deposition: Electrostatics and/or non-electrostatics?

    NARCIS (Netherlands)

    Lyklema, J.; Deschênes, L.

    2011-01-01

    A critical discussion is presented on the properties and prerequisites of adsorbed polyelectrolytes that have to function as substrates for further layer-by-layer deposition. The central theme is discriminating between the roles of electrostatic and non-electrostatic interactions. In order to

  7. Ion adsorption and its influence on direct current electric field induced deformations of flexoelectric nematic layers.

    Science.gov (United States)

    Derfel, Grzegorz; Buczkowska, Mariola

    2011-07-07

    The influence of ion adsorption on the behavior of the nematic liquid crystal layers is studied numerically. The homeotropic flexoelectric layer subjected to the dc electric field is considered. Selective adsorption of positive ions is assumed. The analysis is based on the free energy formalism for ion adsorption. The distributions of director orientation angle, electric potential, and ion concentrations are calculated by numerical resolving of suitable torques equations and Poisson equation. The threshold voltages for the deformations are also determined. It was shown that adsorption affects the distributions of both cations and anions. Sufficiently large number of adsorbed ions leads to spontaneous deformation arising without any threshold if the total number of ions creates sufficiently strong electric field with significant field gradients in the neighborhood of electrodes. The spontaneous deformations are favored by strong flexoelectricity, large thickness, large ion concentrations, weak anchoring, and large adsorption energy.

  8. The adsorber loop concept for the contact between seawater and adsorber granulate

    International Nuclear Information System (INIS)

    Koske, P.H.; Ohlrogge, K.

    1984-01-01

    The present paper deals with the so-called ''adsorber loop concept'' in which the adsorber granulate is carried along with the seawater to be processed in a loop-like configuration and is separated again from the depleted water before this is leaving the adsorption unit. This concept enables high seawater velocities thus reducing the required bed area. Theoretical considerations are presented together with experimental results from field tests. (orig.) [de

  9. Radiolytic stability of gibbsite and boehmite with adsorbed water

    Science.gov (United States)

    Huestis, Patricia; Pearce, Carolyn I.; Zhang, X.; N'Diaye, Alpha T.; Rosso, Kevin M.; LaVerne, Jay A.

    2018-04-01

    Aluminum oxyhydroxide (boehmite, AlOOH) and aluminum hydroxide (gibbsite, Al(OH)3) powders with adsorbed water were irradiated with γ-rays and 5 MeV He ions (α-particles) in order to determine overall radiation stability and chemical modification to the surface. No variation in overall phase or crystallinity due to radiolysis was observed with X-ray diffraction (XRD) and Raman spectroscopy for doses up to 2 MGy with γ-rays and 175 MGy with α-particles. Temperature programed desorption (TPD) of the water from the surface to the gas phase indicated that the water was chemisorbed and strongly bound. Water adsorption sites are of similar energy for both gibbsite and boehmite. Observation of the water adsorbed on the surface of gibbsite and boehmite with diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) showed broad peaks at 3100-3600 cm-1 due to OH stretching that slowly decreased on heating to 500 °C, which corresponds well with the water vapor evolution observed with TPD. Both materials were found to be amorphous following heating to 500 °C. X-ray photoelectron spectroscopy (XPS) indicated surface reduction of Al(III) to Al metal on radiolysis with α-particles. Complete loss of chemisorbed water and the formation of bulk O atoms was observed following radiolysis with α-particles.

  10. Radiolytic stability of gibbsite and boehmite with adsorbed water

    Energy Technology Data Exchange (ETDEWEB)

    Huestis, Patricia; Pearce, Carolyn I.; Zhang, X.; N' Diaye, Alpha T.; Rosso, Kevin M.; LaVerne, Jay A.

    2018-04-01

    Aluminum oxyhydroxide (boehmite, AlOOH) and aluminum hydroxide (gibbsite, Al(OH)3) powders with adsorbed water were irradiated with -rays and 5 MeV He ions (α-particles) in order to determine overall radiation stability and chemical modification to the surface. No variation in overall phase or crystallinity due to radiolysis was observed with X-ray diffraction (XRD) and Raman spectroscopy for doses up to 2 MGy with -rays and 175 MGy with α-particles. Temperature programed desorption (TPD) of the water from the surface to the gas phase indicated that the water was chemisorbed and strongly bound. Water adsorption sites are of similar energy for both gibbsite and boehmite. Observation of the water adsorbed on the surface of gibbsite and boehmite with diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) showed broad peaks at 3100-3600 cm-1 due to OH stretching that slowly decreased on heating to 500oC, which corresponds well with the water vapor evolution observed with TPD. Both materials were found to be amorphous following heating to 500oC. X-ray photoelectron spectroscopy (XPS) indicated surface reduction of Al(III) to Al metal on radiolysis with α-particles. Complete loss of chemisorbed water and the formation of bulk O atoms was observed following radiolysis with α-particles.

  11. Double layers in space

    International Nuclear Information System (INIS)

    Carlqvist, P.

    1982-01-01

    For more than a decade it has been realised that electrostatic double layers are likely to occur in space. The author briefly discusses the theoretical background of such double layers. Most of the paper is devoted to an account of the observational evidence for double layers in the ionosphere and magnetosphere of the Earth. Several different experiments are reviewed including rocket and satellite measurements and ground based observations. It is concluded that the observational evidence for double layers in space is very strong. The experimental results indicate that double layers with widely different properties may exist in space. (Auth.)

  12. Method for removing strongly adsorbed surfactants and capping agents from metal to facilitate their catalytic applications

    Science.gov (United States)

    Adzic, Radoslav R.; Gong, Kuanping; Cai, Yun; Wong, Stanislaus; Koenigsmann, Christopher

    2016-11-08

    A method of synthesizing activated electrocatalyst, preferably having a morphology of a nanostructure, is disclosed. The method includes safely and efficiently removing surfactants and capping agents from the surface of the metal structures. With regard to metal nanoparticles, the method includes synthesis of nanoparticle(s) in polar or non-polar solution with surfactants or capping agents and subsequent activation by CO-adsorption-induced surfactant/capping agent desorption and electrochemical oxidation. The method produces activated macroparticle or nanoparticle electrocatalysts without damaging the surface of the electrocatalyst that includes breaking, increasing particle thickness or increasing the number of low coordination sites.

  13. Zeolites as alcohol adsorbents from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Cekova Blagica

    2006-01-01

    Full Text Available The potential usage of zeolites as adsorbents for the removal of organic molecules from water was investigated in a series of experiments with aqueous solutions of lower alcohols. This could represent a simple solution to the problem of cleaning up industrial wastewater as well as recovering valuable chemicals at relatively low costs. Adsorption isotherms of the Langmuir type were applied, and calculations showed that the amount of propanol adsorbed on silicalite corresponded to approximately 70% of the pore volume. The adsorption process is simple, and recovery of the more concentrated products is easily done by heat treatment and/or at lowered pressures. Adsorption experiments with aqueous acetone showed that silicalite had approximately the same adsorption capacity for acetone as for n-propanol. Heats of adsorption were determined calorimetrically.

  14. Analysis of Adsorbed Natural Gas Tank Technology

    Science.gov (United States)

    Knight, Ernest; Schultz, Conrad; Rash, Tyler; Dohnke, Elmar; Stalla, David; Gillespie, Andrew; Sweany, Mark; Seydel, Florian; Pfeifer, Peter

    With gasoline being an ever decreasing finite resource and with the desire to reduce humanity's carbon footprint, there has been an increasing focus on innovation of alternative fuel sources. Natural gas burns cleaner, is more abundant, and conforms to modern engines. However, storing compressed natural gas (CNG) requires large, heavy gas cylinders, which limits space and fuel efficiency. Adsorbed natural gas (ANG) technology allows for much greater fuel storage capacity and the ability to store the gas at a much lower pressure. Thus, ANG tanks are much more flexible in terms of their size, shape, and weight. Our ANG tank employs monolithic nanoporous activated carbon as its adsorbent material. Several different configurations of this Flat Panel Tank Assembly (FPTA) along with a Fuel Extraction System (FES) were examined to compare with the mass flow rate demands of an engine.

  15. Computer simulations of adsorbed liquid crystal films

    Science.gov (United States)

    Wall, Greg D.; Cleaver, Douglas J.

    2003-01-01

    The structures adopted by adsorbed thin films of Gay-Berne particles in the presence of a coexisting vapour phase are investigated by molecular dynamics simulation. The films are adsorbed at a flat substrate which favours planar anchoring, whereas the nematic-vapour interface favours normal alignment. On cooling, a system with a high molecule-substrate interaction strength exhibits substrate-induced planar orientational ordering and considerable stratification is observed in the density profiles. In contrast, a system with weak molecule-substrate coupling adopts a director orientation orthogonal to the substrate plane, owing to the increased influence of the nematic-vapour interface. There are significant differences between the structures adopted at the two interfaces, in contrast with the predictions of density functional treatments of such systems.

  16. Green Adsorbents for Wastewaters: A Critical Review

    Science.gov (United States)

    Kyzas, George Z.; Kostoglou, Margaritis

    2014-01-01

    One of the most serious environmental problems is the existence of hazardous and toxic pollutants in industrial wastewaters. The major hindrance is the simultaneous existence of many/different types of pollutants as (i) dyes; (ii) heavy metals; (iii) phenols; (iv) pesticides and (v) pharmaceuticals. Adsorption is considered to be one of the most promising techniques for wastewater treatment over the last decades. The economic crisis of the 2000s led researchers to turn their interest in adsorbent materials with lower cost. In this review article, a new term will be introduced, which is called “green adsorption”. Under this term, it is meant the low-cost materials originated from: (i) agricultural sources and by-products (fruits, vegetables, foods); (ii) agricultural residues and wastes; (iii) low-cost sources from which most complex adsorbents will be produced (i.e., activated carbons after pyrolysis of agricultural sources). These “green adsorbents” are expected to be inferior (regarding their adsorption capacity) to the super-adsorbents of previous literature (complex materials as modified chitosans, activated carbons, structurally-complex inorganic composite materials etc.), but their cost-potential makes them competitive. This review is a critical approach to green adsorption, discussing many different (maybe in some occasions doubtful) topics such as: (i) adsorption capacity; (ii) kinetic modeling (given the ultimate target to scale up the batch experimental data to fixed-bed column calculations for designing/optimizing commercial processes) and (iii) critical techno-economical data of green adsorption processes in order to scale-up experiments (from lab to industry) with economic analysis and perspectives of the use of green adsorbents. PMID:28788460

  17. Green Adsorbents for Wastewaters: A Critical Review

    Directory of Open Access Journals (Sweden)

    George Z. Kyzas

    2014-01-01

    Full Text Available One of the most serious environmental problems is the existence of hazardous and toxic pollutants in industrial wastewaters. The major hindrance is the simultaneous existence of many/different types of pollutants as (i dyes; (ii heavy metals; (iii phenols; (iv pesticides and (v pharmaceuticals. Adsorption is considered to be one of the most promising techniques for wastewater treatment over the last decades. The economic crisis of the 2000s led researchers to turn their interest in adsorbent materials with lower cost. In this review article, a new term will be introduced, which is called “green adsorption”. Under this term, it is meant the low-cost materials originated from: (i agricultural sources and by-products (fruits, vegetables, foods; (ii agricultural residues and wastes; (iii low-cost sources from which most complex adsorbents will be produced (i.e., activated carbons after pyrolysis of agricultural sources. These “green adsorbents” are expected to be inferior (regarding their adsorption capacity to the super-adsorbents of previous literature (complex materials as modified chitosans, activated carbons, structurally-complex inorganic composite materials etc., but their cost-potential makes them competitive. This review is a critical approach to green adsorption, discussing many different (maybe in some occasions doubtful topics such as: (i adsorption capacity; (ii kinetic modeling (given the ultimate target to scale up the batch experimental data to fixed-bed column calculations for designing/optimizing commercial processes and (iii critical techno-economical data of green adsorption processes in order to scale-up experiments (from lab to industry with economic analysis and perspectives of the use of green adsorbents.

  18. The effect of adsorbates on the electrical stability of graphene studied by transient photocurrent spectroscopy

    Science.gov (United States)

    Kalkan, S. B.; Aydın, H.; Özkendir, D.; ćelebi, C.

    2018-01-01

    Adsorbate induced variations in the electrical conductivity of graphene layers with two different types of charge carriers are investigated by using the Transient Photocurrent Spectroscopy (TPS) measurement technique. In-vacuum TPS measurements taken for a duration of 5 ks revealed that the adsorption/desorption of atmospheric adsorbates leads to more than a 110% increment and a 45% decrement in the conductivity of epitaxial graphene (n-type) and chemical vapor deposition graphene (p-type) layers on semi-insulating silicon carbide (SiC) substrates, respectively. The graphene layers on SiC are encapsulated and passivated with a thin SiO2 film grown by the Pulsed Electron Deposition method. The measurements conducted for short periods and a few cycles showed that the encapsulation process completely suppresses the time dependent conductivity instability of graphene independent of its charge carrier type. The obtained results are used to construct an experimental model for identifying adsorbate related conductivity variations in graphene and also in other 2D materials with an inherently high surface-to-volume ratio.

  19. Geopolymer as an adsorbent of heavy metal: A review

    Science.gov (United States)

    Ariffin, Nurliyana; Abdullah, Mohamad Mustafa Al Bakri; Zainol, Remy Rozainy Mohd Arif; Murshed, Mohd Fared

    2017-09-01

    This paper reviews about geopolymer based adsorbent focusing in the removal of heavy metal. The reviews include fundamental and types of material used in the formation of adsorbents. Geopolymer based adsorbent got attention recently due to its unique three-dimensional network structure, with fixed size pores and paths that allow certain heavy metal to pass through. Most materials that applied as adsorbent such as fly ash, metakaolin, kaolin and dolomite. A lot of sludge nowadays only dumped in the landfill which can be used as one of new materials as geopolymer based adsorbent.

  20. The adsorber loop concept for the contact between seawater and adsorber granulate

    International Nuclear Information System (INIS)

    Koske, P.H.; Ohlrogge, K.

    1984-01-01

    For the production of 1 kg uranium from seawater about 10 9 kg seawater - depending on the extraction efficiency - have to be processed in a production plant. Such high seawater flows have to be put through adsorber beds the area of which depends on the flow velocity of the water in the bed. For a typical polyamidoxim (PAO) adsorber granulate with a grain size distribution of 0.3 to 1.2 mm the velocity in a fluidized bed is limited to about 1 cm/s in order to prevent carry out of the adsorber material. The consequences of this rather low bed velocity are large and expensive bed areas for technical production plants. The present paper deals with the so-called ''adsorber loop concept'' in which the adsorber granulate is carried along with the seawater to be processed in a loop-like configuration and is separated again from the water before this is leaving the adsorption unit. This concept enables considerably higher seawater velocities thus reducing the bed area. Theoretical considerations are presented together with experimental results from field tests. (author)

  1. Influence of Adsorbed Water on the Oxygen Evolution Reaction on Oxides

    DEFF Research Database (Denmark)

    Siahrostami, Samira; Vojvodic, Aleksandra

    2015-01-01

    We study the interface between adsorbed water and stoichiometric, defect-free (110) rutile oxide surfaces of TiO2, RuO2, and IrO2 in order to understand how water influences the stabilities of the intermediates of the oxygen evolution reaction (OER). In our model the water is treated as explicitly...... molecules binding to bridging oxygens. The third chain interacts weakly and predominantly with the H2O molecules of the second layer, resembling bulk water. We find that the stability of the water layer close to the oxide surface is almost the same as the one found on flat metal surfaces, such as the Pt(111...

  2. Negatively charged ions on Mg(0001) surfaces: appearance and origin of attractive adsorbate-adsorbate interactions.

    Science.gov (United States)

    Cheng, Su-Ting; Todorova, Mira; Freysoldt, Christoph; Neugebauer, Jörg

    2014-09-26

    Adsorption of electronegative elements on a metal surface usually leads to an increase in the work function and decrease in the binding energy as the adsorbate coverage rises. Using density-functional theory calculations, we show that Cl adsorbed on a Mg(0001) surface complies with these expectations, but adsorption of {N,O,F} causes a decrease in the work function and an increase in the binding energy. Analyzing the electronic structure, we show that the presence of a highly polarizable electron spill-out in front of Mg(0001) causes this unusual adsorption behavior and is responsible for the appearance of a hitherto unknown net-attractive lateral electrostatic interaction between same charged adsorbates.

  3. Silver ions/ovalbumin films layer-by-layer self-assembled polyacrylonitrile nanofibrous mats and their antibacterial activity.

    Science.gov (United States)

    Song, Rukun; Yan, Jinjiao; Xu, Shasha; Wang, Yuntao; Ye, Ting; Chang, Jing; Deng, Hongbing; Li, Bin

    2013-08-01

    The CN groups of polyacrylonitrile (PAN) can strongly adsorb silver ions. The possibility of using this attraction as a layer-by-layer (LBL) self-assembly driving force was investigated. Firstly, the surface of the PAN nanofibrous mats was modified by silver ions to make sure it was positively charged. Then oppositely charged ovalbumin (OVA) and silver ions in aqueous media were alternatively deposited onto the surface of the obtained composite mats by layer-by-layer self-assembly technique. The morphology of the LBL films coating mats was observed by field emission scanning electron microscope (FE-SEM). The deposition of silver ions and OVA was confirmed by X-ray photoelectron spectroscopy (XPS) and wide-angle X-ray diffraction (XRD). The thermal degradation properties were investigated by thermo-gravimetric analysis (TGA). Besides these, the cytotoxicity and antibacterial activity of the prepared mats were studied via flow cytometry (FCM) and inhibition zone test, respectively. The results showed that the composite mats after LBL self-assembly processing exhibited improved thermal stability, slightly decreased cytotoxicity, and excellent antibacterial activity against Escherichia coil and Staphylococcus aureus. Copyright © 2013 Elsevier B.V. All rights reserved.

  4. Adsorption equilibria and kinetics for phenol and cresol onto polymeric adsorbents: effects of adsorbents/adsorbates structure and interface.

    Science.gov (United States)

    Liu, Fu-Qiang; Xia, Ming-Fang; Yao, San-Li; Li, Ai-Min; Wu, Hai-Suo; Chen, Jin-Long

    2008-04-01

    Phenol and cresol (o-, m-, and p-) were selected as the adsorbates with different dipole moment (cresol>phenol, methyl being electron-drawing group) and solubility (phenol>cresol, methyl being hydrophobic group). Macropore polymers (NDA-1800 and XAD-4), hypercrosslinked polymers (NDA-100), and chemically modified adsorbents (NDA-150 and NDA-99), were comparatively used to investigate the adsorption properties including equilibria, thermodynamics and kinetics. First, all of the results about equilibria show that the adsorption data fit well to the Freundlich model. The adsorption capacity of NDA-99 and NDA-150 especially for phenol is larger in a certain extent than other three types of polymers. The hydrophobic interaction from large specific surface was mainly occurred, while the polar groups containing oxygen and amine markedly enhance the adsorption process via hydrogen interaction. Furthermore, the adsorption amount for NDA-99 and XAD-4 decrease linearly with the solubility of solutes tested. Then, the negative values of enthalpy demonstrate the predominantly exothermic and physical solid-extraction processes. Finally, the relatively more rapid adsorption process could be found onto NDA-150 than NDA-99, with the reason of the double larger pore size of the former. In conclusion, solubility of solute, together with surface area, pore size and modified groups, extremely exerts influences to the adsorption performances.

  5. Adsorbing staircase polygons subject to a force

    Science.gov (United States)

    Beaton, Nicholas R.

    2017-12-01

    We study several models of staircase polygons on the 45\\circ rotated square lattice, which interact with an impenetrable surface while also being pushed towards or pulled away from the surface by a force. The surface interaction is governed by a fugacity a and the force by a fugacity y. Staircase polygons are simplifications of more general self-avoiding polygons, a well-studied model of interacting ring polymers. For this simplified case we are able to exactly determine the limiting free energy in the full a-y plane, and demonstrate that staircase polygons exhibit four different phases, including a ‘mixed’ adsorbed-ballistic phase.

  6. Testing strong interaction theories

    International Nuclear Information System (INIS)

    Ellis, J.

    1979-01-01

    The author discusses possible tests of the current theories of the strong interaction, in particular, quantum chromodynamics. High energy e + e - interactions should provide an excellent means of studying the strong force. (W.D.L.)

  7. Neutron Diffraction from the Second Layer of 4He on Graphite

    DEFF Research Database (Denmark)

    da Costa Carneiro, Kim; Passell, L.; Thomlinson, W.

    1981-01-01

    Neutron diffraction has been used to study the second atomic layer of **4He adsorbed on graphite. As the **4He-coverage exceeds the first layer, the second initially forms a fluid phase. But when there is enough **4He in the third layer to compress the second, this layer solidifies. The structure...

  8. Development of adsorbents for recovery of uranium from seawater

    International Nuclear Information System (INIS)

    Egawa, Hiroaki; Furusaki, Shintaro.

    1987-01-01

    The largest subject for putting the extraction of uranium from seawater in practical use is the development of high performance adsorbents for uranium. In this paper, the way of thinking about the development of adsorbents for extracting uranium from seawater and the recent reports on this subject are described. Next, the research on the adsorbing capacity and adsorbing rate of the adsorbents developed so far is summarized, and the way of thinking about the evaluation of adsorbent performance which is the base of the design of a system for extracting uranium from seawater is explained, taking amidoxime type adsorbent as the example. For Japan where energy resources are scant, the uranium contained in seawater, which is estimated to be about 4.2 billion t, is the most luring important element. Uranium is contained in seawater is very low concentration of 3 ppb, and exists as anion complex salt. In 1960s, the Harwell Atomic Energy Research Establishment in UK found out that titanium oxide hydrate is the most promising as the adsorbent. Also a number of organic absorbents have been developed. In order to bring adsorbents in contact with seawater, pumping, ocean current and wave force are utilized. Adsorbents are in spherical, fiber and film forms, and held as fixed beds and fluidized beds. (Kako, I.) 48 refs

  9. Adsorption and conformational modification of fibronectin and fibrinogen adsorbed on hydroxyapatite. A QCM-D study.

    Science.gov (United States)

    Fernández-Montes Moraleda, Belén; San Román, Julio; Rodríguez-Lorenzo, Luís M

    2016-10-01

    Hydroxyapatite is a bioactive ceramic frequently used for bone engineering/replacement. One of the parameters that influence the biological response to implanted materials is the conformation of the first adsorbed protein layer. In this work, the adsorption and conformational changes of two fibroid serum proteins; fibronectin and fibrinogen adsorbed onto four different hydroxyapatite powders are studied with a Quartz Crystal Microbalance with Dissipation (QCM-D). Each of the calcined apatites adsorbs less protein than their corresponding synthesized samples. Adsorption on synthesized samples yields always an extended conformation whereas a reorganization of the layer is observed for the calcined samples. Fg acquires a "Side on" conformation in all the samples at the beginning of the experiment except for one of the synthesized samples where an "End-on" conformation is obtained during the whole experiment. The Extended conformation is the active conformation for Fn. This conformation is favored by apatites with large specific surface area (SSA) and on highly concentrated media. Apatite surface features should be considered in the selection or design of materials for bone regeneration, since it is possible to control the conformation mode of attachment of Fn and Fg by an appropriate selection of them. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 2585-2594, 2016. © 2016 Wiley Periodicals, Inc.

  10. Dye sequestration using agricultural wastes as adsorbents

    Directory of Open Access Journals (Sweden)

    Kayode Adesina Adegoke

    2015-12-01

    Full Text Available Color is a visible pollutant and the presence of even minute amounts of coloring substance makes it undesirable due to its appearance. The removal of color from dye-bearing effluents is a major problem due to the difficulty in treating such wastewaters by conventional treatment methods. The most commonly used methods for color removal are biological oxidation and chemical precipitation. However, these processes are effective and economic only in the case where the solute concentrations are relatively high. Most industries use dyes and pigments to color their products. The presence of dyes in effluents is a major concern due to its adverse effect on various forms of life. The discharge of dyes in the environment is a matter of concern for both toxicological and esthetical reasons. It is evident from a literature survey of about 283 recently published papers that low-cost adsorbents have demonstrated outstanding removal capabilities for dye removal and the optimal equilibrium time of various dyes with different charcoal adsorbents from agricultural residues is between 4 and 5 h. Maximum adsorptions of acidic dyes were obtained from the solutions with pH 8–10. The challenges and future prospects are discussed to provide a better framework for a safer and cleaner environment.

  11. Optimizing heterosurface adsorbent synthesis for liquid chromatography

    Science.gov (United States)

    Bogoslovskii, S. Yu.; Serdan, A. A.

    2016-03-01

    The structural and geometric parameters of a silica matrix (SM) for the synthesis of heterosurface adsorbents (HAs) are optimized. Modification is performed by shielding the external surfaces of alkyl-modified silica (AS) using human serum albumin and its subsequent crosslinking. The structural and geometric characteristics of the SM, AS, and HA are measured via low-temperature nitrogen adsorption. It is found that the structural characteristics of AS pores with diameters D 9 nm reduces significantly due to adsorption of albumin. It is concluded that silica gel with a maximum pore size distribution close to 5 nm and a minimal proportion of pores with D > 9 nm is optimal for HA synthesis; this allows us to achieve the greatest similarity between the chromatographic retention parameters for HA and AS. The suitability of the synthesized adsorbents for analyzing drugs in biological fluids through direct sample injection is confirmed by chromatography. It was found that the percentage of the protein fraction detected at the outlet of the chromatographic column is 98%.

  12. Natural adsorbents of dyes from aqueous solution

    Science.gov (United States)

    Rahmani, Meryem; El Hajjaji, souad; Dahchour, Abdelmalek; El M'Rabet, Mohammadine

    2017-04-01

    Contamination of natural waters is a current environmental problem and lot of work has been done to find methods for its, prevention and remediation such as ionic exchange, adsorption on active carbon, filtration, electrolysis, biodegradation …etc. Adsorption is one of the most applied methods according to its effectiveness and easy management. Some adsorbents with good properties such as active alumina, zeolites, crop residues … etc, are suitable to substitute usual active carbon. This study aimed at the removal of dyes using oil shale as natural support, and its optimization by factorial experiment. Three factors were considered namly:pollutant concentration, pH and weight of the adsorbent. Tests have been performed with cationic and anionic dyes. Experimental results show that pseudo-first-order kinetic model provided the best fit to the experimental data for the adsorption by the oil shale. Langmuir, Freundlich and Temkin isotherm models were tested to fit experimental data, the adsorption equilibrium was well described by Freundlich isotherm for methylorange and Temkin for methyl blue. Analysis were completed by oil shale characterization educing XRD, IR, XRF techniques, and cationic exchange capacity.

  13. New type of amidoxime-group-containing adsorbent for the recovery of uranium from seawater. III. Recycle use of adsorbent

    International Nuclear Information System (INIS)

    Omichi, H.; Katakai, A.; Sugo, T.; Okamoto, J.

    1986-01-01

    An amidoxime-group adsorbent for recovering uranium from seawater was made by radiation-induced graft polymerization of acrylonitrile onto polymeric fiber, followed by amidoximation. Uranium adsorption of the adsorbent contacted with seawater in a column increased with the increase in flow rate, then leveled off. The relationship between uranium adsorption in a batch process and the ratio of the amount of seawater to that of adsorbent was found to be effective in evaluating adsorbent contacted with any amount of seawater. The conditioning of the adsorbent with an alkaline solution at higher temperature (∼80 0 C) after the acid desorption recovered the adsorption ability to the original level. This made it possible to apply the adsorbent to recycle use. On the other hand, the adsorbent conditioned at room temperature or that without conditioning lost adsorption ability during recycle use. The increase in water uptake was observed as one of the physical changes produced during recycle use of the alkaline-conditioned adsorbent, while the decrease in water uptake was observed with the unconditioned adsorbent. The IR spectra of the adsorbent showed a probability of reactions of amidoxime groups with acid and alkaline solutions, which can explain the change in uranium adsorption during the adsorption-desorption cycle

  14. Comparison with adsorption of Re (VII) by two different γ-radiation synthesized silica-grafting of vinylimidazole/4-vinylpyridine adsorbents.

    Science.gov (United States)

    Xiao, Pu; Han, Dong; Zhai, Maolin; Xu, Ling; Li, Huibo

    2017-02-15

    Two silica gel based adsorbents for Re (VII), i.e. SS-MPTS-VIMH and SS-MPTS-VPQ, were synthesised. Silica gel was used as the matrix for γ-radiation grafting, and the monomer of 1-vinyl imidazole (VIM) and 4-vinylpyridine (4-VP) was grafted onto the silica silanized by methacryloxy propyl trimethoxyl silane, respectively. A VIM concentration of 2molL -1 and an absorbed dose of 30kGy were the optimal grafting conditions for adsorbent SS-MPTS-VIM, and a 4-VP concentration of 4molL -1 and an absorbed dose of 40kGy were the optimal grafting conditions for adsorbent SS-MPTS-VP. At the certain condition, the grafting yield of SS-MPTS-VIM was 30.1% and that of SS-MPTS-VP was 21.0%. The adsorption capacity of adsorbent SS-MPTS-VIMH was 145.99mgg -1 and that of SS-MPTS-VPQ was 71.08mgg -1 according to the Langmuir model. The adsorbent SS-MPTS-VPQ had better adsorption properties of acid resistance and anti-interference than SS-MPTS-VIMH. Dynamic column experiments showed that protonated adsorbent SS-MTPS-VIMH could be recycled with good performance while quaternized adsorbent SS-MPTS-VPQ could not. The adsorbent SS-MPTS-VIMH belongs to weak anion exchange adsorbent and SS-MPTS-VPQ belongs to strong anion exchange adsorbent. This study paves a way to the synthesis and application of a novel silica base adsorbents for Re (VII). Copyright © 2016 Elsevier B.V. All rights reserved.

  15. Recovery of uranium by CFBA using a granular organic adsorbent

    International Nuclear Information System (INIS)

    Nakamura, Susumu; Oguma, Kouji; Ito, Yoshiro.

    1995-01-01

    Recovery of uranium from natural seawater by a circulating fluidized-bed adsorber (CFBA) was carried out using an organic adsorbent-a granular amidoxime resin (AOR). In the adsorption experiments, stability of the circulating fluidized state of adsorbent and uranium uptake were measured as a function of adsorption time. Results were compared with those obtained for a typical inorganic adsorbent-hydrous titanium oxide granulated with polyacrylonitrile (PAN-HTO). The circulating fluidized state of AOR was very stable. The total amount of carried-over adsorbent was small enough for an adsorption period of 216 hours. The uranium adsorption rates of AOR increased linearly up to the adsorption time of 100 hours, but the increase rate decreased slightly after this time. The uranium amount adsorbed per unit weight of AOR was larger than that of PAN-HTO. The effect of contacting section height of the CFBA on the uranium uptake was also discussed. (author)

  16. Extraction of uranium from seawater using magnetic adsorbents

    International Nuclear Information System (INIS)

    Yamashita, H.; Fujita, K.; Nakajima, F.; Ozawa, Y.; Murata, T.

    1981-01-01

    A new process for the extraction of uranium from seawater was developed. In the process, uranium adsorption is effected using powdered magnetic adsorbents; the adsorbents are then separated from seawater using magnetic separation technology. This process is superior to a column method using a granulated hydrous titanium oxide adsorber bed in the following ways: (1) a higher rate of adsorption is realized because smaller particles are used in the uranium adsorption; and (2) blocking, which is inevitable in an adsorber bed, is eliminated. The composite hydrous titanium-iron oxide as a magnetic adsorbent having high uranium adsorption capacity and magnetization can be prepared by adding urea to a mixed solution of titanium sulfate and ferrous sulfate. Adsorption and desoprtion of uranium and the removal of the adsorbent using a small-scale uranium extraction plant (about 15 m 3 /d) is reported, and the feasibility of uranium extraction from seawater by this process is demonstrated. 10 figures

  17. Procedure of evaluation on adsorbent for extraction of uranium from sea-water

    International Nuclear Information System (INIS)

    Ogata, Noboru

    1982-01-01

    Experimental procedures on the evaluation of adsorbent for the extraction of uranium from seawater and an analytical method of the data were studied on a granulated hydrous titanium oxide as a representative example. Adsorption system for the evaluation adopted a multi-layer and fluidized adsorption bed. The experiment for the evaluation was carried out by using a small column, 2 cm of diameter, for 10 days. The standard condition was 0.6 mm of granule size, 25 0 C of temperature and 10 cm of statistic bed thickness. One of the flow rates was set up at S sub(V) = 2.5 min -1 and another one was set up at two times or a half of the flow rate. The measurements were carried out on the bed thickness of statistic and fluidizing state, granule size, flow rate, temperature, adsorption quantities after 5 and 10 days. An empirical formula on adsorption quantity was derived as follows from these data: C = K 1 t sup(m 1 )K 2 S sub(V)sup(m 2 ). The difference of density between granule and sea-water was decided from grule size, flow rate and expansion ratio by Max Leva's equation. The adsorption ability was expressed by adsorption quantity per unit volume for 10 days at 50% of recovery (standard uranium uptake) or recovery ratio at S sub(V) = 2.5 min -1 (standard recovery). The former could be better because it was applicable to various adsorbents. These results decided the specification of adsorption process, namely the adsorbent inventory and parameters of the design, by application of analytical method to the previous paper. The economical evaluation indicator was mainly composed of the adsorbent inventory, the construction of adsorption bed and the adsorbent supply. An example of the evaluation was shown on a granulated hydrous titanium oxide. (J.P.N.)

  18. XPS and XAS investigation of condensed and adsorbed n-octane on a Cu(110) surface

    International Nuclear Information System (INIS)

    Weiss, K.; Oestroem, H.; Triguero, L.; Ogasawara, H.; Garnier, M.G.; Pettersson, L.G.M.; Nilsson, A.

    2003-01-01

    The electronic structure of n-octane adsorbed on Cu(110) is studied by using X-ray absorption spectroscopy (XAS) and X-ray photoelectron spectroscopy (XPS) in combination with cluster model calculations in the framework of density functional theory (DFT). The molecule is found to be well oriented on the surface, which is seen from the high degree of XAS dichroism. Saturated hydrocarbons are commonly considered to physisorb on metals such as Cu(110), but still the C 1s XAS spectra reveal large changes in the electronic structure of the adsorbed octane relative to the free molecule. We find that the XAS resonances corresponding to the molecular Rydberg-valence states are strongly quenched upon adsorption and that there is a significant hybridization of the molecular valence orbitals with the metal bands. In addition to a precise interpretation of the XAS spectra, we present details on the molecular orbital structure of the adsorbed octane molecule. We also discuss shifts in the relative binding energies of the chemically inequivalent carbon atoms in octane upon adsorption, which lead to a narrower XPS spectrum for the adsorbate than the condensed phase spectrum due to the existence of a new relaxation channel

  19. Study on development of adsorbent of acetaldehyde; Acetaldehyde yo kyuchakuzai no kaihatsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Noda, T. [Nippon Steel Corp., Tokyo (Japan); Suzuki, M. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

    1997-07-10

    The adsorption of acetaldehyde by porous ceramics impregnated with hydrazinium aluminum sulfate (HAS) is studied. Silicagel, activated alumina, activated clay, and activated carbon are compared, and it is found that silicagel and activated clay are suitable as a substrate for HAS impregnated adsorbent. The adsorption mechanism of acetaldehyde by the adsorbent is believed to be one in which acetaldehyde reacts with hydrazinium and yields acetaldazine. The adsorption capacity of the adsorbent at low acetaldehyde concentration of 0.1 ppm was as large as 1.36 mol/kg. This adsorption capacity at 0.1 ppm acetaldehyde concentration is remarkably larger than that of conventional activated carbon. Hydrazinium decomposes easily in the air because it is a strong reducing agent and reacts with oxygen or carbon dioxide. But hydrazinium impregnated on porous ceramics with HAS becomes more stable and maintains reactivity with acetaldehyde for longer than six months. An adsorbent made of porous ceramics impregnated with HAS is useful as a deodorant for acetaldehyde. 8 refs., 6 figs., 6 tabs.

  20. REMOVAL OF REACTIVE DYES FROM WASTEWATER OF TEXTILE INDUSTRIES BY USING ENVIRONMENTAL FRIENDLY ADSORBENTS

    Directory of Open Access Journals (Sweden)

    ALAM Md Shamim

    2016-05-01

    Full Text Available This paper is aimed at developing a method to treat wastewater by using inexpensive adsorbents. Textile industries produce wastewater, otherwise known as effluent, as a bi-product of their production. The effluent contains several pollutants. Among the various stages of textile production, the operations in the dyeing plant, which include pre-treatments, dyeing, printing and finishing, produce the most pollution. The textile dyeing wastes contain unused or partially used organic compounds, and high level of different pollutants. They are often of strong color and may also be of high temperature. When disposed into water bodies or onto land these effluents will result in the deterioration of ecology and damage to aquatic life. Furthermore they may cause damage to fisheries and economic loss to fishermen and farmer, there may be impacts on human health which can be removed with the help of an effluent treatment plant (ETP. The “clean” water can then be safely discharged into the environment and ultimately save our environment from pollution. In this study, rice husk and cotton dust were used as an adsorbent. In this research work waste water was characterized with this useless adsorbents. The parameters which were tested in this study are DO, BOD, COD, TS, TDS and TSS. The results showed that the selected bio adsorbents have good potential for removal of reactive dyes from textile effluent.

  1. Adsorbent Alkali Conditioning for Uranium Adsorption from Seawater. Adsorbent Performance and Technology Cost Evaluation

    International Nuclear Information System (INIS)

    Tsouris, Costas; Mayes, Richard T.; Janke, Christopher James; Dai, Sheng; Das, S.; Liao, W.P.; Kuo, Li-Jung; Wood, Jordana; Gill, Gary; Byers, Maggie Flicker; Schneider, Eric

    2015-01-01

    The Fuel Resources program of the Fuel Cycle Research and Development program of the Office of Nuclear Energy (NE) is focused on identifying and implementing actions to assure that nuclear fuel resources are available in the United States. An immense source of uranium is seawater, which contains an estimated amount of 4.5 billion tonnes of dissolved uranium. This unconventional resource can provide a price cap and ensure centuries of uranium supply for future nuclear energy production. NE initiated a multidisciplinary program with participants from national laboratories, universities, and research institutes to enable technical breakthroughs related to uranium recovery from seawater. The goal is to develop advanced adsorbents to reduce the seawater uranium recovery technology cost and uncertainties. Under this program, Oak Ridge National Laboratory (ORNL) has developed a new amidoxime-based adsorbent of high surface area, which tripled the uranium capacity of leading Japanese adsorbents. Parallel efforts have been focused on the optimization of the physicochemical and operating parameters used during the preparation of the adsorbent for deployment. A set of parameters that need to be optimized are related to the conditioning of the adsorbent with alkali solution, which is necessary prior to adsorbent deployment. Previous work indicated that alkali-conditioning parameters significantly affect the adsorbent performance. Initiated in 2014, this study had as a goal to determine optimal parameters such as base type and concentration, temperature, and duration of conditioning that maximize the uranium adsorption performance of amidoxime functionalized adsorbent, while keeping the cost of uranium production low. After base-treatment at various conditions, samples of adsorbent developed at ORNL were tested in this study with batch simulated seawater solution of 8-ppm uranium concentration, batch seawater spiked with uranium nitrate at 75-100 ppb uranium, and continuous

  2. Adsorbent Alkali Conditioning for Uranium Adsorption from Seawater. Adsorbent Performance and Technology Cost Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Tsouris, Costas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Mayes, Richard T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Janke, Christopher James [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Dai, Sheng [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Das, S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Liao, W. -P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kuo, Li-Jung [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wood, Jordana [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gill, Gary [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Byers, Maggie Flicker [Univ. of Texas, Austin, TX (United States); Schneider, Eric [Univ. of Texas, Austin, TX (United States)

    2015-09-30

    The Fuel Resources program of the Fuel Cycle Research and Development program of the Office of Nuclear Energy (NE) is focused on identifying and implementing actions to assure that nuclear fuel resources are available in the United States. An immense source of uranium is seawater, which contains an estimated amount of 4.5 billion tonnes of dissolved uranium. This unconventional resource can provide a price cap and ensure centuries of uranium supply for future nuclear energy production. NE initiated a multidisciplinary program with participants from national laboratories, universities, and research institutes to enable technical breakthroughs related to uranium recovery from seawater. The goal is to develop advanced adsorbents to reduce the seawater uranium recovery technology cost and uncertainties. Under this program, Oak Ridge National Laboratory (ORNL) has developed a new amidoxime-based adsorbent of high surface area, which tripled the uranium capacity of leading Japanese adsorbents. Parallel efforts have been focused on the optimization of the physicochemical and operating parameters used during the preparation of the adsorbent for deployment. A set of parameters that need to be optimized are related to the conditioning of the adsorbent with alkali solution, which is necessary prior to adsorbent deployment. Previous work indicated that alkali-conditioning parameters significantly affect the adsorbent performance. Initiated in 2014, this study had as a goal to determine optimal parameters such as base type and concentration, temperature, and duration of conditioning that maximize the uranium adsorption performance of amidoxime functionalized adsorbent, while keeping the cost of uranium production low. After base-treatment at various conditions, samples of adsorbent developed at ORNL were tested in this study with batch simulated seawater solution of 8-ppm uranium concentration, batch seawater spiked with uranium nitrate at 75-100 ppb uranium, and continuous

  3. Scanning tunneling microscopy studies of organic monolayers adsorbed on the rhodium(111) crystal surface

    Energy Technology Data Exchange (ETDEWEB)

    Cernota, Paul Davis [Univ. of California, Berkeley, CA (United States)

    1999-08-01

    Scanning Tunneling Microscopy studies were carried out on ordered overlayers on the (111) surface of rhodium. These adsorbates include carbon monoxide (CO), cyclohexane, cyclohexene, 1,4-cyclohexadiene, para-xylene, and meta-xylene. Coadsorbate systems included: CO with ethylidyne, CO with para- and meta-xylene, and para-xylene with meta-xylene. In the case of CO, the structure of the low coverage (2x2) overlayer has been observed. The symmetry of the unit cell in this layer suggests that the CO is adsorbed in the 3-fold hollow sites. There were also two higher coverage surface structures with (√7x√7) unit cells. One of these is composed of trimers of CO and has three CO molecules in each unit cell. The other structure has an additional CO molecule, making a total of four. This extra CO sits on a top site.

  4. WGS-Adsorbent Reaction Studies at Laboratory Scale

    International Nuclear Information System (INIS)

    Marano, M.; Torreiro, Y.

    2014-01-01

    This document reports the most significant results obtained during the experimental work performed under task WGS adsorbent experimental studies within CAPHIGAS project (National Research Plan 2008-2011, ref: ENE2009-08002). The behavior of the binary adsorbent-catalyst system which will be used in the hybrid system is described in this document. Main results reported here were used during the design and development of the hybrid system adsorbent catalyst- membrane proposed in the CAPHIGAS project. The influence of main operating parameters and the optimized volume ratio adsorbent-catalyst are also presented in this report. (Author)

  5. Neutralization of Rubidium Adsorbate Electric Fields by Electron Attachment

    Energy Technology Data Exchange (ETDEWEB)

    Sedlacek, J. A. [Univ. of Oklahoma, Norman, OK (United States); Kim, E. [Univ. of Nevada, Las Vegas, NV (United States); Rittenhouse, S. T. [Western Washington Univ., Bellingham, WA (United States); US Naval Academy, Annapolis, MD (United States); Weck, Philippe F [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sadeghpour, H. R. [Harvard-Smithsonian Center for Astrophysics, Cambridge, MA (United States); Shaffer, J. P. [Univ. of Oklahoma, Norman, OK (United States)

    2015-10-01

    We investigate the (0001) surface of single crystal quartz with a submonolayer of Rb adsorbates. Using Rydberg atom electromagnetically induced transparency, we investigate the electric elds resulting from Rb adsorbed on the quartz surface, and measure the activation energy of the Rb adsorbates. We show that the Rb induces a negative electron affnity (NEA) on the quartz surface. The NEA surface allows for low energy electrons to bind to the surface and cancel the electric eld from the Rb adsorbates. Our results have implications for integrating Rydberg atoms into hybrid quantum systems and the fundamental study of atom-surface interactions, as well as applications for electrons bound to a 2D surface.

  6. Novel structures of oxygen adsorbed on a Zr(0001) surface predicted from first principles

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Bo [State Key Laboratory of Superhard Materials, Jilin University, Changchun, 130012 (China); Beijing computational science research center, Beijing,100084 (China); Wang, Jianyun [State Key Laboratory of Superhard Materials, Jilin University, Changchun, 130012 (China); Lv, Jian [State Key Laboratory of Superhard Materials, Jilin University, Changchun, 130012 (China); College of Materials Science and Engineering, Jilin University, Changchun, 130012 (China); Gao, Xingyu [Laboratory of Computational Physics, Institute of Applied Physics and Computational Mathematics, Beijing, 100088 (China); CAEP Software Center for High Performance Numerical Simulation, Beijing, 100088 (China); Zhao, Yafan [CAEP Software Center for High Performance Numerical Simulation, Beijing, 100088 (China); Wang, Yanchao, E-mail: wyc@calypso.cn [State Key Laboratory of Superhard Materials, Jilin University, Changchun, 130012 (China); Beijing computational science research center, Beijing,100084 (China); College of Materials Science and Engineering, Jilin University, Changchun, 130012 (China); Song, Haifeng, E-mail: song_haifeng@iapcm.ac.cn [Laboratory of Computational Physics, Institute of Applied Physics and Computational Mathematics, Beijing, 100088 (China); CAEP Software Center for High Performance Numerical Simulation, Beijing, 100088 (China); Ma, Yanming [State Key Laboratory of Superhard Materials, Jilin University, Changchun, 130012 (China); Beijing computational science research center, Beijing,100084 (China)

    2017-01-30

    Highlights: • Two stable structures of O adsorbed on a Zr(0001) surface are predicted with SLAM. • A stable structure of O adsorbed on a Zr(0001) surface is proposed with MLAM. • The calculated work function change is agreement with experimental value. - Abstract: The structures of O atoms adsorbed on a metal surface influence the metal properties significantly. Thus, studying O chemisorption on a Zr surface is of great interest. We investigated O adsorption on a Zr(0001) surface using our newly developed structure-searching method combined with first-principles calculations. A novel structural prototype with a unique combination of surface face-centered cubic (SFCC) and surface hexagonal close-packed (SHCP) O adsorption sites was predicted using a single-layer adsorption model (SLAM) for a 0.5 and 1.0 monolayer (ML) O coverage. First-principles calculations based on the SLAM revealed that the new predicted structures are energetically favorable compared with the well-known SFCC structures for a low O coverage (0.5 and 1.0 ML). Furthermore, on basis of our predicted SFCC + SHCP structures, a new structure within multi-layer adsorption model (MLAM) was proposed to be more stable at the O coverage of 1.0 ML, in which adsorbed O atoms occupy the SFCC + SHCP sites and the substitutional octahedral sites. The calculated work functions indicate that the SFCC + SHCP configuration has the lowest work function of all known structures at an O coverage of 0.5 ML within the SLAM, which agrees with the experimental trend of work function with variation in O coverage.

  7. Theoretical insight of physical adsorption for a single-component adsorbent+adsorbate system: I. Thermodynamic property surfaces.

    Science.gov (United States)

    Chakraborty, Anutosh; Saha, Bidyut Baran; Ng, Kim Choon; Koyama, Shigeru; Srinivasan, Kandadai

    2009-02-17

    Thermodynamic property surfaces for a single-component adsorbent+adsorbate system are derived and developed from the viewpoint of classical thermodynamics, thermodynamic requirements of chemical equilibrium, Gibbs law, and Maxwell relations. They enable us to compute the entropy and enthalpy of the adsorbed phase, the isosteric heat of adsorption, specific heat capacity, and the adsorbed phase volume thoroughly. These equations are very simple and easy to handle for calculating the energetic performances of any adsorption system. We have shown here that the derived thermodynamic formulations fill up the information gap with respect to the state of adsorbed phase to dispel the confusion as to what is the actual state of the adsorbed phase. We have also discussed and established the temperature-entropy diagrams of (i) CaCl2-in-silica gel+water system for cooling applications, and (ii) activated carbon (Maxsorb III)+methane system for gas storage.

  8. Theoretical Insight of Physical Adsorption for a Single-Component Adsorbent + Adsorbate System: I. Thermodynamic Property Surfaces

    KAUST Repository

    Chakraborty, Anutosh

    2009-02-17

    Thermodynamic property surfaces for a single-component adsorbent + adsorbate system are derived and developed from the viewpoint of classical thermodynamics, thermodynamic requirements of chemical equilibrium, Gibbs law, and Maxwell relations. They enable us to compute the entropy and enthalpy of the adsorbed phase, the isosteric heat of adsorption, specific heat capacity, and the adsorbed phase volume thoroughly. These equations are very simple and easy to handle for calculating the energetic performances of any adsorption system. We have shown here that the derived thermodynamic formulations fill up the information gap with respect to the state of adsorbed phase to dispel the confusion as to what is the actual state of the adsorbed phase. We have also discussed and established the temperature-entropy diagrams of (i) CaCl 2-in-silica gel + water system for cooling applications, and (ii) activated carbon (Maxsorb III) + methane system for gas storage. © Copyright 2009 American Chemical Society.

  9. Carbon Dioxide Capture Adsorbents: Chemistry and Methods.

    Science.gov (United States)

    Patel, Hasmukh A; Byun, Jeehye; Yavuz, Cafer T

    2017-04-10

    Excess carbon dioxide (CO 2 ) emissions and their inevitable consequences continue to stimulate hard debate and awareness in both academic and public spaces, despite the widespread lack of understanding on what really is needed to capture and store the unwanted CO 2 . Of the entire carbon capture and storage (CCS) operation, capture is the most costly process, consisting of nearly 70 % of the price tag. In this tutorial review, CO 2 capture science and technology based on adsorbents are described and evaluated in the context of chemistry and methods, after briefly introducing the current status of CO 2 emissions. An effective sorbent design is suggested, whereby six checkpoints are expected to be met: cost, capacity, selectivity, stability, recyclability, and fast kinetics. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Applications of core level spectroscopy to adsorbates

    International Nuclear Information System (INIS)

    Nilsson, Anders

    2002-01-01

    In the following review different applications of core-level spectroscopy to atomic and molecular adsorbates will be shown. Core-holes are created through core-level ionization and X-ray absorption processes and the core-hole decays by radiant and non-radiant processes. This forms the basis for X-ray photoelectron spectroscopy, X-ray absorption spectroscopy, Auger electron spectroscopy and X-ray emission spectroscopy. We will demonstrate how we can use the different methods to obtain information about the chemical state, local geometric structure, nature of chemical bonding and dynamics in electron transfer processes. The adsorption of N 2 and CO on Ni(100) will be used as prototype systems for chemisorption while N 2 on graphite and Ar on Pt for physisorption

  11. Selective lanthanide sorption and mechanism using novel hybrid Lewis base (N-methyl-N-phenyl-1,10-phenanthroline-2-carboxamide) ligand modified adsorbent

    International Nuclear Information System (INIS)

    Awual, Md. Rabiul; Kobayashi, Tohru; Miyazaki, Yuji; Motokawa, Ryuhei; Shiwaku, Hideaki; Suzuki, Shinichi; Okamoto, Yoshihiro; Yaita, Tsuyoshi

    2013-01-01

    Highlights: •Hybrid Lewis base adsorbent was prepared for selective lanthanide (Eu, Sm) removal. •Common ions did not interfere due to strong interactions between Eu/Sm and adsorbent. •The adsorbent has good sorption and kinetic performances for potential applications. •The adsorption is reversible and adsorbent reusable in many cycles without any deterioration. -- Abstract: This study aims to develop a highly selective Lewis base adsorbent to investigate the selective sorption and recovery of Eu(III) and Sm(III) from wastewater. The oxygen and nitrogen donor atoms containing Lewis base N-methyl-N-phenyl-1,10-phenanthroline-2-carboxamide (MePhPTA) ligand was synthesized and subsequently an adsorbent was prepared by direct immobilization onto mesoporous silica. Determined maximum adsorption capacities were 125.63 and 124.38 mg/g for Eu(III) and Sm(III), respectively. Experiments with mixed-cations solutions showed that the sequence of preferential adsorption was Eu(III) > Sm(III). The lanthanide sorption by hybrid Lewis base adsorbent (HyLBA) was not adversely affected by the presence of sodium, potassium, calcium, magnesium, chloride, sulfate and nitrate ions due to strong affinity between hard Lewis acid lanthanide and hard Lewis base adsorbent. The crystallography for the Sm-MePhPTA complex suggested that MePhPTA was strongly coordinated to Sm(III) with oxygen and nitrogen by forming a stable complex with two 5-membered rings. The data clarified that bond lengths between Sm(III) and amide oxygen (2.475 Å) were shorter than Sm-N (2.662 Å) in phenanthroline moiety indicating strong oxygen driven HyLBA. The results suggested that HyLBA has a good prospect of promising applications for separation/sorption of lanthanide ions from effluents

  12. Retention of contaminants Cd and Hg adsorbed and intercalated in aluminosilicate clays: A first principles study.

    Science.gov (United States)

    Crasto de Lima, F D; Miwa, R H; Miranda, Caetano R

    2017-11-07

    Layered clay materials have been used to incorporate transition metal (TM) contaminants. Based on first-principles calculations, we have examined the energetic stability and the electronic properties due to the incorporation of Cd and Hg in layered clay materials, kaolinite (KAO) and pyrophyllite (PYR). The TM can be (i) adsorbed on the clay surface as well as (ii) intercalated between the clay layers. For the intercalated case, the contaminant incorporation rate can be optimized by controlling the interlayer spacing of the clay, namely, pillared clays. Our total energy results reveal that the incorporation of the TMs can be maximized through a suitable tuning of vertical distance between the clay layers. Based on the calculated TM/clay binding energies and the Langmuir absorption model, we estimate the concentrations of the TMs. Further kinetic properties have been examined by calculating the activation energies, where we found energy barriers of ∼20 and ∼130 meV for adsorbed and intercalated cases, respectively. The adsorption and intercalation of ionized TM adatoms were also considered within the deprotonated KAO surface. This also leads to an optimal interlayer distance which maximizes the TM incorporation rate. By mapping the total charge transfers at the TM/clay interface, we identify a net electronic charge transfer from the TM adatoms to the topmost clay surface layer. The effect of such a charge transfer on the electronic structure of the clay (host) has been examined through a set of X-ray absorption near edge structure (XANES) simulations, characterizing the changes of the XANES spectra upon the presence of the contaminants. Finally, for the pillared clays, we quantify the Cd and Hg K-edge energy shifts of the TMs as a function of the interlayer distance between the clay layers and the Al K-edge spectra for the pristine and pillared clays.

  13. Retention of contaminants Cd and Hg adsorbed and intercalated in aluminosilicate clays: A first principles study

    Science.gov (United States)

    Crasto de Lima, F. D.; Miwa, R. H.; Miranda, Caetano R.

    2017-11-01

    Layered clay materials have been used to incorporate transition metal (TM) contaminants. Based on first-principles calculations, we have examined the energetic stability and the electronic properties due to the incorporation of Cd and Hg in layered clay materials, kaolinite (KAO) and pyrophyllite (PYR). The TM can be (i) adsorbed on the clay surface as well as (ii) intercalated between the clay layers. For the intercalated case, the contaminant incorporation rate can be optimized by controlling the interlayer spacing of the clay, namely, pillared clays. Our total energy results reveal that the incorporation of the TMs can be maximized through a suitable tuning of vertical distance between the clay layers. Based on the calculated TM/clay binding energies and the Langmuir absorption model, we estimate the concentrations of the TMs. Further kinetic properties have been examined by calculating the activation energies, where we found energy barriers of ˜20 and ˜130 meV for adsorbed and intercalated cases, respectively. The adsorption and intercalation of ionized TM adatoms were also considered within the deprotonated KAO surface. This also leads to an optimal interlayer distance which maximizes the TM incorporation rate. By mapping the total charge transfers at the TM/clay interface, we identify a net electronic charge transfer from the TM adatoms to the topmost clay surface layer. The effect of such a charge transfer on the electronic structure of the clay (host) has been examined through a set of X-ray absorption near edge structure (XANES) simulations, characterizing the changes of the XANES spectra upon the presence of the contaminants. Finally, for the pillared clays, we quantify the Cd and Hg K-edge energy shifts of the TMs as a function of the interlayer distance between the clay layers and the Al K-edge spectra for the pristine and pillared clays.

  14. Friction and diffusion dynamics of adsorbates at surfaces

    NARCIS (Netherlands)

    Fusco, C.

    2005-01-01

    A theoretical study of the motion of adsorbates (e. g. atoms, molecules or clusters) on solid surfaces is presented, with a focus on surface diffusion and atomic-scale friction. These two phenomena are inextricably linked, because when an atomic or molecular adsorbate diffuses, or is pulled, it

  15. Synthesis and properties of porous zeolite aluminosilicate adsorbents

    International Nuclear Information System (INIS)

    Shilina, A.S.; Milinchuk, V.K.; Burukhin, S.B.; Gordienko, A.B.

    2015-01-01

    Environmentally safe non-energy-intensive methods of the synthesis have been developed and the properties of solid inorganic nanostructured zeolite-like adsorbents of a broad spectrum have been studied. The sorption capacities of the adsorbents with respect to various components of water pollution have been determined [ru

  16. Development of ultrafiltration and inorganic adsorbents: January--March 1977

    International Nuclear Information System (INIS)

    Koenst, J.W. Jr.

    1977-01-01

    Ultrafiltration media with and without the assistance of bone char filters were evaluated to determine their effectiveness in removing radionuclides from contaminated solutions. Precipitants, resin, adsorbents, and inorganic adsorbents were studied to determine their effectiveness in decontaminating solutions. A study of the effects of radiation on ultrafiltration media was initiated. An ultrafiltration media pilot plant was ordered and is being installed

  17. Comparative evaluation of selected starches as adsorbent for Thin ...

    African Journals Online (AJOL)

    The most commonly used is silica gel which is an inorganic adsorbent. Organic substances like cellulose, polyethylene are also used. All these are imported into Nigeria and are unhealthy for economic policies. Most commonly used adsorbent may not be easy to produce locally, but starch, which is a very common product, ...

  18. Single bank NOx adsorber for heavy duty diesel engines

    NARCIS (Netherlands)

    Genderen, M. van; Aken, M.G. van

    2003-01-01

    In a NOx adsorber programme the feasibility for applying this technology to heavy duty diesel engines was investigated. After modelling and simulations for realising best λ < 1 engine conditions a platform was build which was used to obtain good NOx adsorber regeneration settings in a number of

  19. Crosslinked xylan as an affinity adsorbent for endo-xylanases.

    NARCIS (Netherlands)

    Rozie, H.; Somers, W.; Bonte, A.; Rombouts, F.M.; Visser, J.

    1992-01-01

    In order to facilitate the purification of xylanases from Aspergillus niger, an affinity adsorbent has been developed from oat spelts xylan. A suitable adsorbent was only obtained by crosslinking oat spelts xylan with epichlorohydrin in water but not in ethanol or ethanol-water mixtures. After some

  20. Gas-Solid Reaction Properties of Fluorine Compounds and Solid Adsorbents for Off-Gas Treatment from Semiconductor Facility

    Directory of Open Access Journals (Sweden)

    Shinji Yasui

    2012-01-01

    Full Text Available We have been developing a new dry-type off-gas treatment system for recycling fluorine from perfluoro compounds present in off-gases from the semiconductor industry. The feature of this system is to adsorb the fluorine compounds in the exhaust gases from the decomposition furnace by using two types of solid adsorbents: the calcium carbonate in the upper layer adsorbs HF and converts it to CaF2, and the sodium bicarbonate in the lower layer adsorbs HF and SiF4 and converts them to Na2SiF6. This paper describes the fluorine compound adsorption properties of both the solid adsorbents—calcium carbonate and the sodium compound—for the optimal design of the fixation furnace. An analysis of the gas-solid reaction rate was performed from the experimental results of the breakthrough curve by using a fixed-bed reaction model, and the reaction rate constants and adsorption capacity were obtained for achieving an optimal process design.

  1. Processing method and device for iodine adsorbing material

    International Nuclear Information System (INIS)

    Watanabe, Shin-ichi; Shiga, Reiko.

    1997-01-01

    An iodine adsorbing material adsorbing silver compounds is reacted with a reducing gas, so that the silver compounds are converted to metal silver and stored. Then, the silver compounds are not melted or recrystallized even under a highly humid condition, accordingly, peeling of the adsorbed materials from a carrier can be prevented, and the iodine adsorbing material can be stored stably. Since the device is disposed in an off gas line for discharging off gases from a nuclear power facility, the iodine adsorbing material formed by depositing silver halides to the carrier is contained, and a reducing or oxidizing gas is supplied to the vessel as required, and silver halides can be converted to metal silver or the metal silver can be returned to silver halide. (T.M.)

  2. Sequestering nickel (ii) ions from aqueous solutions using various adsorbents

    International Nuclear Information System (INIS)

    Bello, O.S.; Adegoke, K.A.; Bello, O.U.

    2014-01-01

    Adsorption process has proven to be one of the best water treatment technologies around the world and activated carbon is undoubtedly considered as a universal adsorbent for the removal of different types of pollutants from water. However, widespread use of commercial activated carbon is sometimes restricted due to its high cost. Attempts have been made to develop inexpensive adsorbents utilizing numerous agro-industrial and municipal waste materials. Use of agricultural waste materials as low-cost adsorbents is attractive because it reduces the cost of waste disposal, thereby leading to environmental protection. In this review, agricultural, synthetic and other adsorbents used for adsorbing nickel (II) ion from aqueous solutions are reported. Different ways to improve their efficiencies are also discussed. (author)

  3. Noble gas separation with the use of inorganic adsorbents

    International Nuclear Information System (INIS)

    Pence, D.T.; Chou, C.C.; Christian, J.D.; Paplawsky, W.J.

    1979-01-01

    A noble gas separation process is proposed for application to airborne nuclear fuel reprocessing plant effluents. The process involves the use of inorganic adsorbents for the removal of contaminant gases and noble gas separation through selective adsorption. Water and carbon dioxide are removed with selected zeolites that do not appreciably adsorb the noble gases. Xenon is essentially quantitatively removed with a specially developed adsorbent using conventional adsorption-desorption techniques. Oxygen is removed to low ppM levels by the use of a rapid cycle adsorption technique on a special adsorbent leaving a krypton-nitrogen mixture. Krypton is separated from nitrogen with a special adsorbent operated at about -80 0 C. Because the separation process does not require high pressures and oxygen is readily removed to sufficiently limit ozone formation to insignificant levels, appreciable capital and operating cost savings with this process are possible compared with other proposed processes. In addition, the proposed process is safer to operate

  4. Surface atomic relaxation and magnetism on hydrogen-adsorbed Fe(110) surfaces from first principles

    Science.gov (United States)

    Chohan, Urslaan K.; Jimenez-Melero, Enrique; Koehler, Sven P. K.

    2016-11-01

    We have computed adsorption energies, vibrational frequencies, surface relaxation and buckling for hydrogen adsorbed on a body-centred-cubic Fe(110) surface as a function of the degree of H coverage. This adsorption system is important in a variety of technological processes such as the hydrogen embrittlement in ferritic steels, which motivated this work, and the Haber-Bosch process. We employed spin-polarised density functional theory to optimise geometries of a six-layer Fe slab, followed by frozen mode finite displacement phonon calculations to compute Fe-H vibrational frequencies. We have found that the quasi-threefold (3f) site is the most stable adsorption site, with adsorption energies of ∼3.0 eV/H for all coverages studied. The long-bridge (lb) site, which is close in energy to the 3f site, is actually a transition state leading to the stable 3f site. The calculated harmonic vibrational frequencies collectively span from 730 to 1220 cm-1, for a range of coverages. The increased first-to-second layer spacing in the presence of adsorbed hydrogen, and the pronounced buckling observed in the Fe surface layer, may facilitate the diffusion of hydrogen atoms into the bulk, and therefore impact the early stages of hydrogen embrittlement in steels.

  5. Strongly Correlated Topological Insulators

    Science.gov (United States)

    2016-02-03

    Strongly Correlated Topological Insulators In the past year, the grant was used for work in the field of topological phases, with emphasis on finding...surface of topological insulators. In the past 3 years, we have started a new direction, that of fractional topological insulators. These are materials...in which a topologically nontrivial quasi-flat band is fractionally filled and then subject to strong interactions. The views, opinions and/or

  6. Modeling the binding of fulvic acid by goethite: the speciation of adsorbed FA molecules

    Science.gov (United States)

    Filius, Jeroen D.; Meeussen, Johannes C. L.; Lumsdon, David G.; Hiemstra, Tjisse; van Riemsdijk, Willem H.

    2003-04-01

    Under natural conditions, the adsorption of ions at the solid-water interface may be strongly influenced by the adsorption of organic matter. In this paper, we describe the adsorption of fulvic acid (FA) by metal(hydr)oxide surfaces with a heterogeneous surface complexation model, the ligand and charge distribution (LCD) model. The model is a self-consistent combination of the nonideal competitive adsorption (NICA) equation and the CD-MUSIC model. The LCD model can describe simultaneously the concentration, pH, and salt dependency of the adsorption with a minimum of only three adjustable parameters. Furthermore, the model predicts the coadsorption of protons accurately for an extended range of conditions. Surface speciation calculations show that almost all hydroxyl groups of the adsorbed FA molecules are involved in outer sphere complexation reactions. The carboxylic groups of the adsorbed FA molecule form inner and outer sphere complexes. Furthermore, part of the carboxylate groups remain noncoordinated and deprotonated.

  7. DNA binding during expanded bed adsorption and factors affecting adsorbent aggregation

    DEFF Research Database (Denmark)

    Arpanaei, Ayyoob; Mathiasen, N.; Hobley, Timothy John

    2008-01-01

    DNA-induced aggregation and contraction of expanded bed adsorption chromatography beds have been examined using strong anion exchanger Q HyperZ and calf thymus DNA in buffers containing added NaCl. Two batches of adsorbent with different ionic capacities were used allowing the effects of different...... tolerance of anion exchangers when binding DNA. However, more importantly. with the adsorbents examined here. attempts to reduce bed aggregation by feedstock conditioning with added salt may increase DNA binding leading to a reduction in expanded bed adsorption performance compromising protein capture...... ligand densities to be examined. Very high dynamic binding capacities at 10% breakthrough were found in the absence of added salt. However, the highest binding capacities (similar to 10 and similar to 19mg DNA ml(-1) gel) were found in buffers containing added salt at concentrations of either 0.25 or 0...

  8. Strong Cosmic Censorship

    Science.gov (United States)

    Isenberg, James

    2017-01-01

    The Hawking-Penrose theorems tell us that solutions of Einstein's equations are generally singular, in the sense of the incompleteness of causal geodesics (the paths of physical observers). These singularities might be marked by the blowup of curvature and therefore crushing tidal forces, or by the breakdown of physical determinism. Penrose has conjectured (in his `Strong Cosmic Censorship Conjecture`) that it is generically unbounded curvature that causes singularities, rather than causal breakdown. The verification that ``AVTD behavior'' (marked by the domination of time derivatives over space derivatives) is generically present in a family of solutions has proven to be a useful tool for studying model versions of Strong Cosmic Censorship in that family. I discuss some of the history of Strong Cosmic Censorship, and then discuss what is known about AVTD behavior and Strong Cosmic Censorship in families of solutions defined by varying degrees of isometry, and discuss recent results which we believe will extend this knowledge and provide new support for Strong Cosmic Censorship. I also comment on some of the recent work on ``Weak Null Singularities'', and how this relates to Strong Cosmic Censorship.

  9. Development of boundary layers

    International Nuclear Information System (INIS)

    Herbst, R.

    1980-01-01

    Boundary layers develop along the blade surfaces on both the pressure and the suction side in a non-stationary flow field. This is due to the fact that there is a strongly fluctuating flow on the downstream blade row, especially as a result of the wakes of the upstream blade row. The author investigates the formation of boundary layers under non-stationary flow conditions and tries to establish a model describing the non-stationary boundary layer. For this purpose, plate boundary layers are measured, at constant flow rates but different interferent frequency and variable pressure gradients. By introducing the sample technique, measurements of the non-stationary boundary layer become possible, and the flow rate fluctuation can be divided in its components, i.e. stochastic turbulence and periodical fluctuation. (GL) [de

  10. Prediction of crack propagation in layered ceramics with strong interfaces

    Czech Academy of Sciences Publication Activity Database

    Náhlík, Luboš; Šestáková, L.; Hutař, Pavel; Bermejo, R.

    2010-01-01

    Roč. 77, č. 11 (2010), s. 2192-2199 ISSN 0013-7944 R&D Projects: GA AV ČR(CZ) KJB200410803; GA ČR GA101/09/1821 Institutional research plan: CEZ:AV0Z20410507 Keywords : Ceramic laminate * Crack propagation direction * Residual stress * Flaw tolerant ceramics * Optimal design Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 1.571, year: 2010

  11. Adsorbed or intercalated: Na on graphene/Ir(111)

    Science.gov (United States)

    Pervan, Petar; Lazić, Predrag

    2017-09-01

    Interaction of sodium with graphene (Gr) on Ir(111) was studied with the aim to resolve the issue of Na adsorption/intercalation kinetics. The system Na/Gr/Ir(111) was studied by means of angle-resolved photoemission spectroscopy, low-energy electron diffraction, and ab initio density functional theory (DFT) calculation. It has been found that at room temperature (RT) and low concentrations Na is dominantly adsorbed on graphene. At higher concentrations, an intercalation process sets in so that it is possible to observe the coexistence of these two states. Eventually, all Na atoms are found in the intercalated state as determined by exposure to oxygen. While adsorption of Na on graphene already intercalated by Na [Na/Gr/Na/Ir(111) system] at RT was not possible, we could observe Li adsorption through the increase of Dirac point binding energy. Li coadsorption strongly affects the binding energy of the iridium surface state as well. This finding was supported by DFT calculations of adsorption energy of Na and Li on bare and fully Na intercalated graphene.

  12. Ion exchangers as adsorbents for removing metals from aquatic media.

    Science.gov (United States)

    Khan, Meraj A; Bushra, Rani; Ahmad, Anees; Nabi, Syed A; Khan, Dilwar A; Akhtar, Arshia

    2014-02-01

    A polyaniline-based composite cation-exchange material was synthesized by way of sol-gel method and studied to explore its analytical and environmental applications. It was characterized by using instrumental analyses [Fourier transform infrared (spectrometer), X-ray, thermogravimetric analysis/differential thermal analysis, standard electron microscopy, and transmission electron microscopy]. Physicochemical studies, such as ion-exchange capacity, pH titrations, and chemical stability, along with effect of eluent concentration and elution, were also performed to exploit the ion-exchange capabilities. pH titration studies showed that the material presents monofunctional strong cation-exchange behavior. This nanocomposite material is semicrystalline in nature and exhibits improved thermal and chemical stability. The partition coefficient studies of different metal ions in the material were performed in demineralised water and different surfactant media, and it was found to be selective for Pb(II) and Hg(II) ions. To exploit the usefulness of the material as an adsorbent, some important quantitative binary separations of metal ions were performed on polyaniline Zr(IV) molybdophosphate columns. This composite cation exchanger can be applied for the treatment of polluted water to remove heavy metals.

  13. A DFT study of Cu nanoparticles adsorbed on defective graphene

    Energy Technology Data Exchange (ETDEWEB)

    García-Rodríguez, D.E. [Universidad Politécnica de Aguascalientes, Calle Paseo San Gerardo No. 297 Fracc. San Gerardo, 20342 Aguascalientes, Ags. (Mexico); Mendoza-Huizar, L.H. [Universidad Autónoma del Estado de Hidalgo, Área Académica de Química, Ciudad del Conocimiento. Carretera Pachuca-Tulancigo Km. 4.5 Mineral de la Reforma, 42186 Hidalgo (Mexico); Díaz, C., E-mail: cristina.diaz@uam.es [Departamento de Química, Módulo 13, Universidad Autónoma de Madrid, 28049 Madrid (Spain); Condensed Matter Physics Center (IFIMAC), Universidad Autónoma de Madrid, 28049 Madrid (Spain); Institute for Advanced Research in Chemical Science (IAdChem), Universidad Autónoma de Madrid, 28049 Madrid (Spain)

    2017-08-01

    Highlights: • Cu{sub n} supported on graphene may be a promising electrode material for DBFC's cells. • Cu{sub n}/graphene interaction is rather local and size independent. • Cu{sub 13} anchors strongly to defects in graphene, while keeping its gas-phase properties. - Abstract: Metal nanoparticles adsorbed on graphene are systems of interest for processes relative to catalytic reactions and alternative energy production. Graphene decorated with Cu-nanoparticles, in particular, could be a good alternative material for electrodes in direct borohydride fuel cells. However our knowledge of this system is still very limited. Based on density functional theory, we have analyzed the interaction of Cu{sub n} nanoparticles (n = 4, 5, 6, 7, 13) with pristine and defective-graphene. We have considered two types of defects, a single vacancy (SV), and an extended lineal structural defect (ELSD), formed by heptagon-pentagon pairs. Our analysis has revealed the covalent character of the Cu{sub n}-graphene interaction for pristine- and ELSD-graphene, and a more ionic-like interaction for SV-graphene. Furthermore, our analysis shows that the interaction between the nanoparticles and the graphene is rather local, i.e., only the nanoparticle atoms close to the contact region are involved in the interaction, being the electronic contact region much higher for defective-graphene than for pristine-graphene. Thus, the higher the particle the lower its average electronic and structural distortion.

  14. A DFT study of Cu nanoparticles adsorbed on defective graphene

    International Nuclear Information System (INIS)

    García-Rodríguez, D.E.; Mendoza-Huizar, L.H.; Díaz, C.

    2017-01-01

    Highlights: • Cu n supported on graphene may be a promising electrode material for DBFC's cells. • Cu n /graphene interaction is rather local and size independent. • Cu 13 anchors strongly to defects in graphene, while keeping its gas-phase properties. - Abstract: Metal nanoparticles adsorbed on graphene are systems of interest for processes relative to catalytic reactions and alternative energy production. Graphene decorated with Cu-nanoparticles, in particular, could be a good alternative material for electrodes in direct borohydride fuel cells. However our knowledge of this system is still very limited. Based on density functional theory, we have analyzed the interaction of Cu n nanoparticles (n = 4, 5, 6, 7, 13) with pristine and defective-graphene. We have considered two types of defects, a single vacancy (SV), and an extended lineal structural defect (ELSD), formed by heptagon-pentagon pairs. Our analysis has revealed the covalent character of the Cu n -graphene interaction for pristine- and ELSD-graphene, and a more ionic-like interaction for SV-graphene. Furthermore, our analysis shows that the interaction between the nanoparticles and the graphene is rather local, i.e., only the nanoparticle atoms close to the contact region are involved in the interaction, being the electronic contact region much higher for defective-graphene than for pristine-graphene. Thus, the higher the particle the lower its average electronic and structural distortion.

  15. Scanning tunneling microscopy I general principles and applications to clean and adsorbate-covered surfaces

    CERN Document Server

    Wiesendanger, Roland

    1992-01-01

    Scanning Tunneling Microscopy I provides a unique introduction to a novel and fascinating technique that produces beautiful images of nature on an atomic scale. It is the first of three volumes that together offer a comprehensive treatment of scanning tunneling microscopy, its diverse applications, and its theoretical treatment. In this volume the reader will find a detailed description of the technique itself and of its applications to metals, semiconductors, layered materials, adsorbed molecules and superconductors. In addition to the many representative results reviewed, extensive references to original work will help to make accessible the vast body of knowledge already accumulated in this field.

  16. Milestone Report - Complete New Adsorbent Materials for Marine Testing to Demonstrate 4.5 g-U/kg Adsorbent

    Energy Technology Data Exchange (ETDEWEB)

    Janke, Christopher James [ORNL; Das, Sadananda [ORNL; Oyola, Yatsandra [ORNL; Mayes, Richard T. [ORNL; Saito, Tomonori [ORNL; Brown, Suree [ORNL; Gill, Gary [PNNL; Kuo, Li-Jung [PNNL; Wood, Jordana [PNNL

    2014-08-01

    This report describes work on the successful completion of Milestone M2FT-14OR03100115 (8/20/2014) entitled, “Complete new adsorbent materials for marine testing to demonstrate 4.5 g-U/kg adsorbent”. This effort is part of the Seawater Uranium Recovery Program, sponsored by the U.S. Department of Energy, Office of Nuclear Energy, and involved the development of new adsorbent materials at the Oak Ridge National Laboratory (ORNL) and marine testing at the Pacific Northwest National Laboratory (PNNL). ORNL has recently developed two new families of fiber adsorbents that have demonstrated uranium adsorption capacities greater than 4.5 g-U/kg adsorbent after marine testing at PNNL. One adsorbent was synthesized by radiation-induced graft polymerization of itaconic acid and acrylonitrile onto high surface area polyethylene fibers followed by amidoximation and base conditioning. This fiber showed a capacity of 4.6 g-U/kg adsorbent in marine testing at PNNL. The second adsorbent was prepared by atom-transfer radical polymerization of t-butyl acrylate and acrylonitrile onto halide-functionalized round fibers followed by amidoximation and base hydrolysis. This fiber demonstrated uranium adsorption capacity of 5.4 g-U/kg adsorbent in marine testing at PNNL.

  17. Bioavailability of Carbon Nanomaterial-Adsorbed Polycyclic Aromatic Hydrocarbons to Pimphales promelas: Influence of Adsorbate Molecular Size and Configuration.

    Science.gov (United States)

    Linard, Erica N; Apul, Onur G; Karanfil, Tanju; van den Hurk, Peter; Klaine, Stephen J

    2017-08-15

    Despite carbon nanomaterials' (CNMs) potential to alter the bioavailability of adsorbed contaminants, information characterizing the relationship between adsorption behavior and bioavailability of CNM-adsorbed contaminants is still limited. To investigate the influence of CNM morphology and organic contaminant (OC) physicochemical properties on this relationship, adsorption isotherms were generated for a suite of polycyclic aromatic hydrocarbons (PAHs) on multiwalled carbon nanotubes (MWCNTs) and exfoliated graphene (GN) in conjunction with determining the bioavailability of the adsorbed PAHs to Pimphales promelas using bile analysis via fluorescence spectroscopy. Although it appeared that GN adsorbed PAHs indiscriminately compared to MWCNTs, the subsequent bioavailability of GN-adsorbed PAHs was more sensitive to PAH morphology than MWCNTs. GN was effective at reducing bioavailability of linear PAHs by ∼70%, but had little impact on angular PAHs. MWCNTs were sensitive to molecular size, where bioavailability of two-ringed naphthalene was reduced by ∼80%, while bioavailability of the larger PAHs was reduced by less than 50%. Furthermore, the reduction in bioavailability of CNM-adsorbed PAHs was negatively correlated with the amount of CNM surface area covered by the adsorbed-PAHs. This study shows that the variability in bioavailability of CNM-adsorbed PAHs is largely driven by PAH size, configuration and surface area coverage.

  18. Accelerator Analysis of Tributyltin Adsorbed onto the Surface of a Tributyltin Resistant Marine Pseudoalteromonas sp. Cell

    Directory of Open Access Journals (Sweden)

    Akira Kitamura

    2008-10-01

    Full Text Available Tributyltin (TBT released into seawater from ship hulls is a stable marine pollutant and obviously remains in marine environments. We isolated a TBT resistant marine Pseudoalteromonas sp. TBT1 from sediment of a ship’s ballast water. The isolate (109.3 ± 0.2 colony-forming units mL-1 adsorbed TBT in proportion to the concentrations of TBTCl externally added up to 3 mM, where the number of TBT adsorbed by a single cell was estimated to be 108.2. The value was reduced to about one-fifth when the lysozyme-treated cells were used. The surface of ethanol treated cells became rough, but the capacity of TBT adsorption was the same as that for native cells. These results indicate that the function of the cell surface, rather than that structure, plays an important role to the adsorption of TBT. The adsorption state of TBT seems to be multi-layer when the number of more than 106.8 TBT molecules is adsorbed by a single cell.

  19. Substructure and in vitro assembly of the outer, structured layer of Spirillum serpens.

    Science.gov (United States)

    Buckmire, F L; Murray, R G

    1976-01-01

    Electron micrographs of disintegrating units of the outer, structured (HP) layer of Spirillum serpens and of the isolated protein obtained from the HP layer revealed V- and Y-shaped and linear profiles. Interpretation of these forms, influenced by the seemingly trimeric form of the isolated protein and by biochemical data, suggested that the protein subunits were identical and Y shaped. A model is proposed for the assembly of the Y-shaped subunits to form a hexagon composed of two triads (three Y-shaped subunits each). The isolated protein adsorbed to a template of wall fragments (basal layer) to the same degree (over 90%) in high concentrations of Na+, K+ (5 X 10(-2) M), Ca2+, Sr2+, and Mg2+ (10(-2) M). At a lower concentration (4 x 10(-5) M) of the cations there was differential adsorption of the protein. Adsorption to the template in the presence of each cation, followed by dilution, also led to differential release of the protein. The adsorption of the protein to the basal layer was correlated with reassembly of the HP layer on the template. The mechanisms seem to be: (i) an ionic strength-dependent reassembly, which results in an HP layer loosely attached to the template (this layer is easily dissociated by decreasing the ionic strength); and (ii) a cation-specific (Ca2+ or Sr2+, but not Mg2+, Na+, or K+) mechanism independent of ionic strength. In this latter case, the specific cations presumably form strong noncovalent "salt" linkages between triads and the basal layer, enabling stable hexagons and the HP layer to be formed.

  20. Inference of polymer adsorption from electrical double layer measurements : the silver iodide-polyvinyl alcohol system

    NARCIS (Netherlands)

    Koopal, L.K.

    1978-01-01

    The purpose of this study was to investigate how the double layer properties of charged particles are modified by the presence of adsorbed polymer molecules and to obtain information on the conformation of the polymer layer from the observed alterations in the double layer

  1. Strong Arcwise Connectedness

    OpenAIRE

    Espinoza, Benjamin; Gartside, Paul; Kovan-Bakan, Merve; Mamatelashvili, Ana

    2012-01-01

    A space is `n-strong arc connected' (n-sac) if for any n points in the space there is an arc in the space visiting them in order. A space is omega-strong arc connected (omega-sac) if it is n-sac for all n. We study these properties in finite graphs, regular continua, and rational continua. There are no 4-sac graphs, but there are 3-sac graphs and graphs which are 2-sac but not 3-sac. For every n there is an n-sac regular continuum, but no regular continuum is omega-sac. There is an omega-sac ...

  2. Abortion: Strong's counterexamples fail

    DEFF Research Database (Denmark)

    Di Nucci, Ezio

    2009-01-01

    This paper shows that the counterexamples proposed by Strong in 2008 in the Journal of Medical Ethics to Marquis's argument against abortion fail. Strong's basic idea is that there are cases--for example, terminally ill patients--where killing an adult human being is prima facie seriously morally......'s scenarios have some valuable future or admitted that killing them is not seriously morally wrong. Finally, if "valuable future" is interpreted as referring to objective standards, one ends up with implausible and unpalatable moral claims....

  3. Modification of Oil Palm Plantation Wastes as Oil Adsorbent for Palm Oil Mill Effluent (POME)

    International Nuclear Information System (INIS)

    Noraisah Jahi; Ling, E.S.; Rizafizah Othaman; Suria Ramli

    2015-01-01

    This research was conducted to modify oil palm solid wastes chemically to become oil adsorbent for palm oil mill effluent (POME). The purpose of modification on oil palm leaves (OPL) and oil palm frond (OPF) was to change the hydrophilic nature to a more hydrophobic character. This study also exploited the production of sorbent materials with high efficiency in the oil uptake for POME from OPL and OPF. Chemical modification was carried out using 200 mL of 1.0 M lauric acid solution for 6 hrs at room temperature. The modified OPL and OPF were preceded to adsorption test for POME and the capacity of oil adsorbed was compared between them. FTIR analysis supported the modification to occur with the increase in a peak of C-H group and the presence of C=O originated from lauric acid structure chain. The hydrophobicity of modified OPL and OPF samples was supported by XRD and contact angle analysis with modified OPL became more hydrophobic than the modified OPF, which had been 38.15 % and 24.67 % respectively. Both the analyses proved that the result from the oil adsorption test on POME showed the presence of a new peak attribute at C=C stretching of aromatics for the oil in POME proved that it was attached on the sorbent materials. Based on SEM analysis, the perforated and rough surface had been observed on modified OPL and OPF samples because oil layers on OPL and OPF surfaces were observed on the modified samples after the adsorption test. All the analyses in the study agreed that the results from oil adsorption test showed that the modified OPL had higher adsorption capacity than the modified OPF with the percentage of oil uptake at 83.74 % and 39.84 % respectively. The prepared adsorbent showed the potential to be used as a low-cost adsorbent in oil for POME. (author)

  4. A strong comeback

    International Nuclear Information System (INIS)

    Marier, D.

    1992-01-01

    This article presents the results of a financial rankings survey which show a strong economic activity in the independent energy industry. The topics of the article include advisor turnover, overseas banks, and the increase in public offerings. The article identifies the top project finance investors for new projects and restructurings and rankings for lenders

  5. [Study on LDL adsorbent modified by lauric acid].

    Science.gov (United States)

    Cong, Haixia; Du, Longbing; Fang, Bo; You, Chao

    2010-06-01

    A hydrophobic low-density lipoprotein cholesterol (LDL-C) adsorbent was synthesized with lauric acid and chitosan. The condition for adsorption was obtained by investigating the influence of adsorbent amount and adsorption time. The results of adsorption in vitro showed that the average adsorption rates for total cholesterol (TC), LDL-C, high-density lipoprotein cholesterol (HDL-C) and total protein (TP) were 47.7%, 84.7%, 18.1% and 5.9% respectively. The adsorbent possesses good selectivity in removing LDL-C.

  6. VOC Recovery through Microwave Regeneration of Adsorbents: Process Design Studies.

    Science.gov (United States)

    Price, David W; Schmidt, Philip S

    1998-12-01

    Process design studies are described for a new type of VOC recovery system which uses microwave heating to regenerate adsorbents. Microwave regeneration systems create a highly concentrated effluent from which the VOCs can be recovered by condensation at near-ambient temperatures. Important design considerations, predicated on experimental work and model development, are identified and discussed. Parametric studies are then described that identify the optimal adsorbent selection, operating cycle, recovery configuration, regeneration pressure, regeneration final coverage, and column configuration. In general, it was found that microwave regenerated adsorption systems favor the use of low dielectric loss-factor polymeric adsorbents and operation under low pressure conditions (about 5 torr absolute pressure).

  7. Comparison with adsorption of Re (VII) by two different γ-radiation synthesized silica-grafting of vinylimidazole/4-vinylpyridine adsorbents

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Pu [Beijing Key Laboratory for Solid Waste Utilization and Management, Department of Energy and Resources Engineering, College of Engineering, Peking University, Beijing 100871,China (China); Han, Dong; Zhai, Maolin [Beijing National Laboratory for Molecular Sciences, Radiochemistry and Radiation Chemistry Key Laboratory of Fundamental Science, The Key Laboratory of Polymer Chemistry and Physics of the Ministry of Education, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Xu, Ling, E-mail: lingxu@pku.edu.cn [Beijing Key Laboratory for Solid Waste Utilization and Management, Department of Energy and Resources Engineering, College of Engineering, Peking University, Beijing 100871,China (China); Li, Huibo, E-mail: hb0012@sina.com [China Institute of Atomic Energy, P.O. Box 275-26, Beijing 102413 (China)

    2017-02-15

    Highlights: • Two Re adsorbents were synthesized by grafting of vinylimidazole and vinylpyridine onto silanized silica gel via γ-radiation. • The Re adsorption capacities of SS-MPTS-VIMH and SS-MPTS-VPQ were 145.99 mg g{sup −1} and 71.08 mg g{sup −1}, respectively. • Both the adsorbents had fast adsorption kinetics, and could be used for column adsorption. • SS-MPTS-VPQ had good anti-interference abilities, and might be used for the disposal of Tc in the future. - Abstract: Two silica gel based adsorbents for Re (VII), i.e. SS-MPTS-VIMH and SS-MPTS-VPQ, were synthesised. Silica gel was used as the matrix for γ-radiation grafting, and the monomer of 1-vinyl imidazole (VIM) and 4-vinylpyridine (4-VP) was grafted onto the silica silanized by methacryloxy propyl trimethoxyl silane, respectively. A VIM concentration of 2 mol L{sup −1} and an absorbed dose of 30 kGy were the optimal grafting conditions for adsorbent SS-MPTS-VIM, and a 4-VP concentration of 4 mol L{sup −1} and an absorbed dose of 40 kGy were the optimal grafting conditions for adsorbent SS-MPTS-VP. At the certain condition, the grafting yield of SS-MPTS-VIM was 30.1% and that of SS-MPTS-VP was 21.0%. The adsorption capacity of adsorbent SS-MPTS-VIMH was 145.99 mg g{sup −1} and that of SS-MPTS-VPQ was 71.08 mg g{sup −1} according to the Langmuir model. The adsorbent SS-MPTS-VPQ had better adsorption properties of acid resistance and anti-interference than SS-MPTS-VIMH. Dynamic column experiments showed that protonated adsorbent SS-MTPS-VIMH could be recycled with good performance while quaternized adsorbent SS-MPTS-VPQ could not. The adsorbent SS-MPTS-VIMH belongs to weak anion exchange adsorbent and SS-MPTS-VPQ belongs to strong anion exchange adsorbent. This study paves a way to the synthesis and application of a novel silica base adsorbents for Re (VII).

  8. An in situ XPS study of L-cysteine co-adsorbed with water on polycrystalline copper and gold

    Science.gov (United States)

    Jürgensen, Astrid; Raschke, Hannes; Esser, Norbert; Hergenröder, Roland

    2018-03-01

    The interactions of biomolecules with metal surfaces are important because an adsorbed layer of such molecules introduces complex reactive functionality to the substrate. However, studying these interactions is challenging: they usually take place in an aqueous environment, and the structure of the first few monolayers on the surface is of particular interest, as these layers determine most interfacial properties. Ideally, this requires surface sensitive analysis methods that are operated under ambient conditions, for example ambient pressure x-ray photoelectron spectroscopy (AP-XPS). This paper focuses on an AP-XPS study of the interaction of water vapour and l-Cysteine on polycrystalline copper and gold surfaces. Thin films of l-Cysteine were characterized with XPS in UHV and in a water vapour atmosphere (P ≤ 1 mbar): the structure of the adsorbed l-Cysteine layer depended on substrate material and deposition method, and exposure of the surface to water vapour led to the formation of hydrogen bonds between H2O molecules and the COO- and NH2 groups of adsorbed l-Cysteine zwitterions and neutral molecules, respectively. This study also proved that it is possible to investigate monolayers of biomolecules in a gas atmosphere with AP-XPS using a conventional laboratory Al-Kα x-ray source.

  9. Directed paths in a layered environment

    International Nuclear Information System (INIS)

    Alvarez, J; Janse van Rensburg, E J

    2008-01-01

    A polymer in a layered environment is modeled as a directed path in a layered square lattice composed of alternating A-layers of width w a and B-layers of width w b . In this paper we consider general cases of this model, where edges in the path interact with the layers, and vertices in the path interact with interfaces between adjacent layers. The phase diagram exhibits different regimes. In particular, we found that the path may be localized to one layer, be adsorbed on an interface between two layers or be delocalized across layers. We examine special aspects of the model in detail: the asymptotic regimes of the models are examined, and entropic forces on the interfaces are determined. We focus on several different cases, including models with layers of equal or similar width. More general models of layers with different but finite widths, or with one layer of infinite width, are also examined in detail. Several of these models exhibit phase behavior which relate to well-studied polymer phase behavior such as adsorption at an impenetrable wall, pinning at an interface between two immiscible solvents, steric stabilization of colloidal particles and sensitized flocculation of colloidal particles by polymers

  10. Dynamics of CO 2 Adsorption on Amine Adsorbents. 2. Insights Into Adsorbent Design

    KAUST Repository

    Bollini, Praveen

    2012-11-21

    Packed bed breakthrough experiments are reported for commercial zeolite 13X and 3-aminopropyl-functionalized SBA-15 silica materials with three different amine loadings. Mass and heat transfer dynamics for all four materials are modeled successfully. Amine adsorbents with open pores are found to exhibit faster mass diffusion rates compared to zeolite 13X. When amine loading is increased by coupling aminopropyl groups, premature breakthrough combined with a long tail is observed. Contrary to conventional physisorbants, finite heat losses to the column wall do not explain the long breakthrough tail. A rate model that accounts for heterogeneity in diffusion was found to accurately capture the breakthrough shape of the high loading material. Batch uptake measurements support the hypothesis that slow diffusion through the polymer phase is what hampers adsorption kinetics in the high amine loading adsorbent. The results emphasize the importance of designing materials that are not overloaded with amine sites, as excessive amine loadings can lead to depressed adsorption kinetics and premature column breakthrough. © 2012 American Chemical Society.

  11. Strong Electroweak Symmetry Breaking

    CERN Document Server

    Grinstein, Benjamin

    2011-01-01

    Models of spontaneous breaking of electroweak symmetry by a strong interaction do not have fine tuning/hierarchy problem. They are conceptually elegant and use the only mechanism of spontaneous breaking of a gauge symmetry that is known to occur in nature. The simplest model, minimal technicolor with extended technicolor interactions, is appealing because one can calculate by scaling up from QCD. But it is ruled out on many counts: inappropriately low quark and lepton masses (or excessive FCNC), bad electroweak data fits, light scalar and vector states, etc. However, nature may not choose the minimal model and then we are stuck: except possibly through lattice simulations, we are unable to compute and test the models. In the LHC era it therefore makes sense to abandon specific models (of strong EW breaking) and concentrate on generic features that may indicate discovery. The Technicolor Straw Man is not a model but a parametrized search strategy inspired by a remarkable generic feature of walking technicolor,...

  12. Natural waste materials containing chitin as adsorbents for textile dyestuffs: batch and continuous studies.

    Science.gov (United States)

    Figueiredo, S A; Loureiro, J M; Boaventura, R A

    2005-10-01

    In this work three natural waste materials containing chitin were used as adsorbents for textile dyestuffs, namely the Anodonta (Anodonta cygnea) shell, the Sepia (Sepia officinalis) and the Squid (Loligo vulgaris) pens. The selected dyestuffs were the Cibacron green T3G-E (CI reactive green 12), and the Solophenyl green BLE 155% (CI direct green 26), both from CIBA, commonly used in cellulosic fibres dyeing, the most used fibres in the textile industry. Batch equilibrium studies showed that the materials' adsorption capacities increase after a simple and inexpensive chemical treatment, which increases their porosity and chitin relative content. Kinetic studies suggested the existence of a high internal resistance in both systems. Fixed bed column experiments performed showed an improvement in adsorbents' behaviour after chemical treatment. However, in the column experiments, the biodegradation was the main mechanism of dyestuff removal, allowing the materials' bioregeneration. The adsorption was strongly reduced by the pore clogging effect of the biomass. The deproteinised Squid pen (grain size 0.500-1.41 mm) is the adsorbent with highest adsorption capacity (0.27 and 0.037 g/g, respectively, for the reactive and direct dyestuffs, at 20 degrees C), followed by the demineralised Sepia pen and Anodonta shell, behaving like pure chitin in all experiments, but showing inferior performances than the granular activated carbon tested in the column experiments.

  13. Adsorbate shape selectivity: Separation of the HF/134a azeotrope over carbogenic molecular sieve

    Energy Technology Data Exchange (ETDEWEB)

    Hong, A.; Mariwala, R.K.; Kane, M.S.; Foley, H.C. [Univ. of Delaware, Nework, DE (United States)

    1995-03-01

    Experimental evidence is provided for adsorptive shape selectivity in the separation of the azeotrope between HF and 1,1,1,2-tetrafluoroethane (134a) over pyrolyzed poly(furfuryl alcohol)-derived carbogenic molecular sieve (PPFA-CMS). The separation can be accomplished over coconut charcoal or Carbosieve G on the basis of the differences in the extent of equilibrium adsorption of HF and 134a. On these adsorbents 134a is more strongly bound than HF, thus it elutes much more slowly from the bed. The heat of adsorption for 134a in the vicinity of 200 C on Carbosieve G is {approximately}8.8 kcal/mol. In contrast, when the same azeotropic mixture is separated over PPFA-CMS prepared at 500 C, 134a is not adsorbed. As a result 134a elutes from the bed first, followed by HF. The reversal is brought about by the narrower pore size and pore size distribution of the PPFA-CMS versus that for Carbosieve G. Thus the separation over PPFA-CMS is an example of adsorbate shape selectivity and represents a limiting case of kinetic separation.

  14. XPS and XAS investigation of condensed and adsorbed n-octane on a Cu(110) surface

    CERN Document Server

    Weiss, K; Triguero, L; Ogasawara, H; Garnier, M G; Pettersson, L G M; Nilsson, A

    2003-01-01

    The electronic structure of n-octane adsorbed on Cu(110) is studied by using X-ray absorption spectroscopy (XAS) and X-ray photoelectron spectroscopy (XPS) in combination with cluster model calculations in the framework of density functional theory (DFT). The molecule is found to be well oriented on the surface, which is seen from the high degree of XAS dichroism. Saturated hydrocarbons are commonly considered to physisorb on metals such as Cu(110), but still the C 1s XAS spectra reveal large changes in the electronic structure of the adsorbed octane relative to the free molecule. We find that the XAS resonances corresponding to the molecular Rydberg-valence states are strongly quenched upon adsorption and that there is a significant hybridization of the molecular valence orbitals with the metal bands. In addition to a precise interpretation of the XAS spectra, we present details on the molecular orbital structure of the adsorbed octane molecule. We also discuss shifts in the relative binding energies of the ...

  15. Plasmons in strong superconductors

    International Nuclear Information System (INIS)

    Baldo, M.; Ducoin, C.

    2011-01-01

    We present a study of the possible plasmon excitations that can occur in systems where strong superconductivity is present. In these systems the plasmon energy is comparable to or smaller than the pairing gap. As a prototype of these systems we consider the proton component of Neutron Star matter just below the crust when electron screening is not taken into account. For the realistic case we consider in detail the different aspects of the elementary excitations when the proton, electron components are considered within the Random-Phase Approximation generalized to the superfluid case, while the influence of the neutron component is considered only at qualitative level. Electron screening plays a major role in modifying the proton spectrum and spectral function. At the same time the electron plasmon is strongly modified and damped by the indirect coupling with the superfluid proton component, even at moderately low values of the gap. The excitation spectrum shows the interplay of the different components and their relevance for each excitation modes. The results are relevant for neutrino physics and thermodynamical processes in neutron stars. If electron screening is neglected, the spectral properties of the proton component show some resemblance with the physical situation in high-T c superconductors, and we briefly discuss similarities and differences in this connection. In a general prospect, the results of the study emphasize the role of Coulomb interaction in strong superconductors.

  16. Enhanced vanillin production from ferulic acid using adsorbent resin.

    Science.gov (United States)

    Hua, Dongliang; Ma, Cuiqing; Song, Lifu; Lin, Shan; Zhang, Zhaobin; Deng, Zixin; Xu, Ping

    2007-03-01

    High vanillin productivity was achieved in the batch biotransformation of ferulic acid by Streptomyces sp. strain V-1. Due to the toxicity of vanillin and the product inhibition, fed-batch biotransformation with high concentration of ferulic acid was unsuccessful. To solve this problem and improve the vanillin yield, a biotransformation strategy using adsorbent resin was investigated. Several macroporous adsorbent resins were chosen to adsorb vanillin in situ during the bioconversion. Resin DM11 was found to be the best, which adsorbed the most vanillin and the least ferulic acid. When 8% resin DM11 (wet w/v) was added to the biotransformation system, 45 g l(-1) ferulic acid could be added continually and 19.2 g l(-1) vanillin was obtained within 55 h, which was the highest vanillin yield by bioconversion until now. This yield was remarkable for exceeding the crystallization concentration of vanillin and therefore had far-reaching consequence in its downstream processing.

  17. TESTING OF CARBONACEOUS ADSORBENTS FOR REMOVAL OF POLLUTANTS FROM WATER

    Directory of Open Access Journals (Sweden)

    RAISA NASTAS

    2012-03-01

    Full Text Available Testing of carbonaceous adsorbents for removal of pollutants from water. Relevant direction for improving of quality of potable water is application of active carbons at various stages of water treatments. This work includes complex research dealing with testing of a broad spectrum of carbonaceous adsorbents for removal of hydrogen sulfide and nitrite ions from water. The role of the surface functional groups of carbonaceous adsorbents, their acid-basic properties, and the influence of the type of impregnated heteroatom (N, O, or metals (Fe, Cu, Ni, on removal of hydrogen sulfide species and nitrite ions have been researched. The efficiency of the catalyst obtained from peach stones by impregnation with Cu2+ ions of oxidized active carbon was established, being recommended for practical purposes to remove the hydrogen sulfide species from the sulfurous ground waters. Comparative analysis of carbonaceous adsorbents reveals the importance of surface chemistry for oxidation of nitrite ions.

  18. Production of Flocculants, Adsorbents, and Dispersants from Lignin

    Directory of Open Access Journals (Sweden)

    Jiachuan Chen

    2018-04-01

    Full Text Available Currently, lignin is mainly produced in pulping processes, but it is considered as an under-utilized chemical since it is being mainly used as a fuel source. Lignin contains many hydroxyl groups that can participate in chemical reactions to produce value-added products. Flocculants, adsorbents, and dispersants have a wide range of applications in industry, but they are mainly oil-based chemicals and expensive. This paper reviews the pathways to produce water soluble lignin-based flocculants, adsorbents, and dispersants. It provides information on the recent progress in the possible use of these lignin-based flocculants, adsorbents, and dispersants. It also critically discusses the advantages and disadvantages of various approaches to produce such products. The challenges present in the production of lignin-based flocculants, adsorbents, and dispersants and possible scenarios to overcome these challenges for commercial use of these products in industry are discussed.

  19. Production of Flocculants, Adsorbents, and Dispersants from Lignin.

    Science.gov (United States)

    Chen, Jiachuan; Eraghi Kazzaz, Armin; AlipoorMazandarani, Niloofar; Hosseinpour Feizi, Zahra; Fatehi, Pedram

    2018-04-10

    Currently, lignin is mainly produced in pulping processes, but it is considered as an under-utilized chemical since it is being mainly used as a fuel source. Lignin contains many hydroxyl groups that can participate in chemical reactions to produce value-added products. Flocculants, adsorbents, and dispersants have a wide range of applications in industry, but they are mainly oil-based chemicals and expensive. This paper reviews the pathways to produce water soluble lignin-based flocculants, adsorbents, and dispersants. It provides information on the recent progress in the possible use of these lignin-based flocculants, adsorbents, and dispersants. It also critically discusses the advantages and disadvantages of various approaches to produce such products. The challenges present in the production of lignin-based flocculants, adsorbents, and dispersants and possible scenarios to overcome these challenges for commercial use of these products in industry are discussed.

  20. Adsorption of remazol brilliant blue on an orange peel adsorbent

    Directory of Open Access Journals (Sweden)

    M. R. Mafra

    2013-09-01

    Full Text Available A novel orange peel adsorbent developed from an agricultural waste material was characterised and utilised for the removal of Remazol Brilliant Blue from an artificial textile-dye effluent. The adsorption thermodynamics of this dye-adsorbent pair was studied in a series of equilibrium experiments. The time to reach equilibrium was 15 h for the concentration range of 30 mg L-1 to 250 mg L-1. The adsorption capacity decreased with increasing temperature, from 9.7 mg L-1 at 20 ºC to 5.0 mg L-1 at 60 ºC. Both the Langmuir and Freundlich isotherm models fitted the adsorption data quite reasonably. The thermodynamic analysis of dye adsorption onto the orange peel adsorbent indicated its endothermic and spontaneous nature. Thus, the application of orange peel adsorbent for the removal of dye from a synthetic textile effluent was successfully demonstrated.

  1. Adsorption of uranium on adsorbents produced from used tires

    International Nuclear Information System (INIS)

    Mahramanlioglu, M.

    2003-01-01

    Potential use of adsorbents produced from used tires for the removal of uranium from aqueous solutions is investigated. Two different adsorbents were used including char and activated carbon produced from used tires. The surface area was larger on activated carbon. Adsorption experiments were carried out as a function of time, adsorbent concentration, pH and initial concentration of uranium. The adsorption kinetics was found to follow the Lagergren equation. The rate constants of intraparticle diffusion and mass transfer coefficients were calculated. It was shown that the equilibrium data could be fitted by the Langmuir and Freundlich equations. The adsorption of uranium in the presence of different cations were also studied and the results were correlated with the ionic potential of the cations. It was demonstrated that the activated carbon produced from used tires can be considered as an adsorbent that has a commercial potential for uranium removal. (author)

  2. Low Pressure Adsorbent for Recovery & Storage Vented Hydrogen, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — A high performance fullerene-based adsorbent is proposed for recovery and storage hydrogen and separating helium via pressure-swing-adsorption (PSA) process....

  3. Order-disorder transitions in adsorbed systems on magnetic surfaces

    International Nuclear Information System (INIS)

    Aguilera-Granja, F.; Moran-Lopez, J.L.; Instituto Politecnico Nacional, Mexico City. Centro de Investigacion y de Estudios Avanzados); Falicov, L.M.

    1984-01-01

    It is investigated the effect of adsorbed atoms on the magnetic properties of ferromagnets. The Ising model is employed considering nearest neigbours with antiferromagnetic coupling between atoms. (M.W.O.) [pt

  4. A Novel Amperometric Glutamate Biosensor Based on Glutamate Oxidase Adsorbed on Silicalite

    Science.gov (United States)

    Soldatkina, O. V.; Soldatkin, O. O.; Kasap, B. Ozansoy; Kucherenko, D. Yu.; Kucherenko, I. S.; Kurc, B. Akata; Dzyadevych, S. V.

    2017-04-01

    In this work, we developed a new amperometric biosensor for glutamate detection using a typical method of glutamate oxidase (GlOx) immobilization via adsorption on silicalite particles. The disc platinum electrode ( d = 0.4 mm) was used as the amperometric sensor. The procedure of biosensor preparation was optimized. The main parameters of modifying amperometric transducers with a silicalite layer were determined along with the procedure of GlOx adsorption on this layer. The biosensors based on GlOx adsorbed on silicalite demonstrated high sensitivity to glutamate. The linear range of detection was from 2.5 to 450 μM, and the limit of glutamate detection was 1 μM. It was shown that the proposed biosensors were characterized by good response reproducibility during hours of continuous work and operational stability for several days. The developed biosensors could be applied for determination of glutamate in real samples.

  5. Magnetization switching in ferromagnets by adsorbed chiral molecules without current or external magnetic field

    Science.gov (United States)

    Ben Dor, Oren; Yochelis, Shira; Radko, Anna; Vankayala, Kiran; Capua, Eyal; Capua, Amir; Yang, See-Hun; Baczewski, Lech Tomasz; Parkin, Stuart Stephen Papworth; Naaman, Ron; Paltiel, Yossi

    2017-02-01

    Ferromagnets are commonly magnetized by either external magnetic fields or spin polarized currents. The manipulation of magnetization by spin-current occurs through the spin-transfer-torque effect, which is applied, for example, in modern magnetoresistive random access memory. However, the current density required for the spin-transfer torque is of the order of 1 × 106 A.cm-2, or about 1 × 1025 electrons s-1 cm-2. This relatively high current density significantly affects the devices' structure and performance. Here we demonstrate magnetization switching of ferromagnetic thin layers that is induced solely by adsorption of chiral molecules. In this case, about 1013 electrons per cm2 are sufficient to induce magnetization reversal. The direction of the magnetization depends on the handedness of the adsorbed chiral molecules. Local magnetization switching is achieved by adsorbing a chiral self-assembled molecular monolayer on a gold-coated ferromagnetic layer with perpendicular magnetic anisotropy. These results present a simple low-power magnetization mechanism when operating at ambient conditions.

  6. Oil palm biomass as an adsorbent for heavy metals.

    Science.gov (United States)

    Vakili, Mohammadtaghi; Rafatullah, Mohd; Ibrahim, Mahamad Hakimi; Abdullah, Ahmad Zuhairi; Salamatinia, Babak; Gholami, Zahra

    2014-01-01

    Many industries discharge untreated wastewater into the environment. Heavy metals from many industrial processes end up as hazardous pollutants of wastewaters.Heavy metal pollution has increased in recent decades and there is a growing concern for the public health risk they may pose. To remove heavy metal ions from polluted waste streams, adsorption processes are among the most common and effective treatment methods. The adsorbents that are used to remove heavy metal ions from aqueous media have both advantages and disadvantages. Cost and effectiveness are two of the most prominent criteria for choosing adsorbents. Because cost is so important, great effort has been extended to study and find effective lower cost adsorbents.One class of adsorbents that is gaining considerable attention is agricultural wastes. Among many alternatives, palm oil biomasses have shown promise as effective adsorbents for removing heavy metals from wastewater. The palm oil industry has rapidly expanded in recent years, and a large amount of palm oil biomass is available. This biomass is a low-cost agricultural waste that exhibits, either in its raw form or after being processed, the potential for eliminating heavy metal ions from wastewater. In this article, we provide background information on oil palm biomass and describe studies that indicate its potential as an alternative adsorbent for removing heavy metal ions from wastewater. From having reviewed the cogent literature on this topic we are encouraged that low-cost oil-palm-related adsorbents have already demonstrated outstanding removal capabilities for various pollutants.Because cost is so important to those who choose to clean waste streams by using adsorbents, the use of cheap sources of unconventional adsorbents is increasingly being investigated. An adsorbent is considered to be inexpensive when it is readily available, is environmentally friendly, is cost-effective and be effectively used in economical processes. The

  7. Residence time determination for adsorbent beds of different configurations

    Energy Technology Data Exchange (ETDEWEB)

    Otermat, J.E.; Wikoff, W.O.; Kovach, J.L.

    1995-02-01

    The residence time calculations of ASME AG-1 Code, Section FC, currently specify a screen surface area method, that is technically incorrect. Test data has been obtained on Type II adsorber trays of different configurations to establish residence time in the adsorber trays. These data indicate that the air volume/carbon volume ratio or the average screen area are more appropriate for the calculation of the residence time calculation than the currently used, smallest screen area basis.

  8. Residence time determination for adsorbent beds of different configurations

    International Nuclear Information System (INIS)

    Otermat, J.E.; Wikoff, W.O.; Kovach, J.L.

    1995-01-01

    The residence time calculations of ASME AG-1 Code, Section FC, currently specify a screen surface area method, that is technically incorrect. Test data has been obtained on Type II adsorber trays of different configurations to establish residence time in the adsorber trays. These data indicate that the air volume/carbon volume ratio or the average screen area are more appropriate for the calculation of the residence time calculation than the currently used, smallest screen area basis

  9. Isotherms, kinetics and thermodynamic studies of adsorption of Cu2+ from aqueous solutions by Mg2+/K+ type orange peel adsorbents.

    Science.gov (United States)

    Liang, Sha; Guo, Xueyi; Feng, Ningchuan; Tian, Qinghua

    2010-02-15

    Orange peel (OP) was used as raw material to prepare two novel adsorbents: MgOP (Mg(2+) type orange peel adsorbent) and KOP (K(+) type orange peel adsorbent). FTIR and SEM were used to characterize the adsorbents. Effects of pH, solid/liquid ratio, time and metal ion concentration on the Cu(2+) adsorption by these two adsorbents were investigated. The isotherms data were analyzed using the Langmuir, Freudlich, Temkin and Dubinin-Radushkevich models. Langmuir model provides the best correlation for the adsorption of Cu(2+) by both MgOP and KOP, and the mono-layer adsorption capacity for Cu(2+) removal by MgOP and KOP are 40.37 and 59.77 mg/g, respectively. The adsorbed amounts of Cu(2+) increased with the increase in contact time and reached equilibrium within 20 min. The kinetics data were analyzed using four adsorption kinetic models: the pseudo-first and second-order equations, the Elovich equation and intraparticle diffusion equation. Results show that the pseudo-second-order equation fits the experimental data very well. Thermodynamic studies showed the spontaneous and exothermic nature of the adsorption of Cu(2+) by MgOP and KOP.

  10. Efficient adsorbents of nanoporous aluminosilicate monoliths for organic dyes from aqueous solution.

    Science.gov (United States)

    El-Safty, Sherif A; Shahat, Ahmed; Awual, Md Rabiul

    2011-07-01

    Growing public awareness on the potential risk to humans of toxic chemicals in the environment has generated demand for new and improved methods for toxicity assessment and removal, rational means for health risk estimation. With the aim of controlling nanoscale adsorbents for functionality in molecular sieving of organic pollutants, we fabricated cubic Im3m mesocages with uniform entrance and large cavity pores of aluminosilicates as highly promising candidates for the colorimetric monitoring of organic dyes in an aqueous solution. However, a feasible control over engineering of three-dimensional (3D) mesopore cage structures with uniform entrance (~5 nm) and large cavity (~10 nm) allowed the development of nanoadsorbent membranes as a powerful tool for large-quantity and high-speed (in minutes) adsorption/removal of bulk molecules such as organic dyes. Incorporation of high aluminum contents (Si/Al=1) into 3D cubic Im3m cage mesoporous silica monoliths resulted in small, easy-to-use optical adsorbent strips. In such adsorption systems, natural surfaces of active acid sites of aluminosilicate strips strongly induced both physical adsorption of chemically responsive dyes and intraparticle diffusion into cubic Im3m mesocage monoliths. Results likewise indicated that although aluminosilicate strips with low Si/Al ratios exhibit distortion in pore ordering and decrease in surface area and pore volume, enhancement of both molecular converges and intraparticle diffusion onto the network surfaces and into the pore architectures of adsorbent membranes was achieved. Moreover, 3D mesopore cage adsorbents are reversible, offering potential for multiple adsorption assays. Copyright © 2011 Elsevier Inc. All rights reserved.

  11. AC microcalorimetry of adsorbates on evaporated metal films: Orientational ordering of H sub 2 multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Phelps, R.B.

    1991-11-01

    We have improved and extended a novel ac calorimetric technique for measuring the heat capacity of adsorbates on evaporated metal films. Metallic substrates are of particular interest in current studies of the thermodynamics of adsorbed molecules. The method described in the present work is only calorimetric technique which allows measurements of molecules on simple metallic surfaces. Among other improvements, we have achieved significant progress in the preparation and characterization of the evaporated metal film. We have applied this novel technique to a study of hydrogen multilayers on gold and sapphire substrates. We have shown that samples of normal-hydrogen with a nominal coverage n of approximately 25 monolayers (ML) undergo a bulk-like orientational ordering transition. The transition is suppressed as the coverage is decreased, and no sign of the transition remains above 1.6 K for n {approx} 1 ML. For n {approx lt} 8 ML, the peak in the heat capacity exhibits signs of finite-size effects. At higher coverages, finite-size effects are not observed, and the shape of the peak depends strongly on the substrate. We conclude that the peak is inhomogeneously broadened for n {approx lt} 8 ML. This work represents the first measurements of the heat capacity due to orientational ordering in adsorbed hydrogen. The results of an earlier experiment involving vibrational spectroscopy of adsorbed molecules are included in the Appendix. In this work, we have used infrared emission spectroscopy to study the spectral region in the vicinity of the C=O stretch vibration of bridge-bonded CO on Pt(111).

  12. Determination of Points of Zero Charge of Natural and Treated Adsorbents

    Science.gov (United States)

    Nasiruddin Khan, M.; Sarwar, Anila

    Although particle size and its measurement are intuitively familiar to particle technologists, the concept of point of zero charge (pzc) is less widely understood and applied. This is unfortunate since it is at least as fundamentally important as particle size in determining the behavior of particulate materials, especially those with sizes in the colloidal range below a micrometer. pzc is related to the charge on the surface of the particle and strongly depends on the pH of the material; so it influences a wide range of properties of colloidal materials, such as their stability, interaction with electrolytes, suspension rheology, and ion exchange capacity. The pH dependence of surface charges was quantified for four different adsorbent-aqueous solution interfaces. The points of zero charge were determined for activated charcoal, granite sand, lakhra coal, and ground corn cob materials using three methods: (1) the pH drift method, measuring pH where the adsorbent behaves as a neutral specie; (2) potentiometric titration, measuring the adsorption of H+ and OH- on surfaces in solutions of varying ionic strengths; (3) direct assessment of the surface charge via nonspecific ion adsorption as a function of pH. The intrinsic acidity constants for acid and base equilibria, pK a1 s and pK a2 s, were also calculated. Lakhra coal was found to have the lowest pzc value among all other adsorbents studied owing to the presence of a large amount of humus material. The results were used to explain general connections among points of zero charges, cation exchange capacity, and base saturation % of adsorbents.

  13. Effect of interfacial properties on the activation volume of adsorbed enzymes.

    Science.gov (United States)

    Schuabb, Vitor; Cinar, Süleyman; Czeslik, Claus

    2016-04-01

    We have studied the enzymatic activities of α-chymotrypsin (α-CT) and horseradish peroxidase (HRP) that are adsorbed on various chemically modified planar surfaces under aqueous solution. The enzymes were adsorbed on bare quartz, hydrophobic poly(styrene) (PS), positively charged poly(allylamine hydrochloride) (PAH), and negatively charged poly(styrene sulfonate) (PSS). Activation volumes of the enzymes at the aqueous-solid interfaces were determined by using high-pressure total internal reflection fluorescence (TIRF) spectroscopy. Apparently, the pressure response of the adsorbed enzymes strongly depends on the interfacial properties. α-CT can be activated by pressure (increasing enzymatic rate) on negatively charged surfaces like quartz and PSS, whereas HRP is activated by pressure on hydrophobic PS. Corresponding negative activation volumes of -29 mL mol(-1) for α-CT on quartz, -23 mL mol(-1) for α-CT on PSS, and -35 mL mol(-1) for HRP on PS are found. In addition, the absolute activities of α-CT and HRP on quartz, PS, PAH and PSS were determined by UV absorption at ambient pressure. Remarkably, large activities are found on those surfaces that are associated with negative activation volumes. However, Fourier transform infrared (FTIR) spectra collected in attenuated total reflection (ATR) mode do not indicate major adsorption induced conformational changes of the enzymes at any interface studied. Overall, the results of this study show that the activity of immobilized enzymes can largely be enhanced by the right combination of adsorbent material and applied pressure. Copyright © 2016 Elsevier B.V. All rights reserved.

  14. Surface atomic relaxation and magnetism on hydrogen-adsorbed Fe(110) surfaces from first principles

    Energy Technology Data Exchange (ETDEWEB)

    Chohan, Urslaan K.; Jimenez-Melero, Enrique [School of Materials, The University of Manchester, Manchester M13 9PL (United Kingdom); Dalton Cumbrian Facility, The University of Manchester, Moor Row CA24 3HA (United Kingdom); Koehler, Sven P.K., E-mail: sven.koehler@manchester.ac.uk [Dalton Cumbrian Facility, The University of Manchester, Moor Row CA24 3HA (United Kingdom); School of Chemistry, The University of Manchester, Manchester M13 9PL (United Kingdom); Photon Science Institute, The University of Manchester, Manchester M13 9PL (United Kingdom)

    2016-11-30

    Highlights: • Potential energy surfaces for H diffusion on Fe(110) calculated. • Full vibrational analysis of surface modes performed. • Vibrational analysis establishes lb site as a transition state to the 3f site. • Pronounced buckling observed in the Fe surface layer. - Abstract: We have computed adsorption energies, vibrational frequencies, surface relaxation and buckling for hydrogen adsorbed on a body-centred-cubic Fe(110) surface as a function of the degree of H coverage. This adsorption system is important in a variety of technological processes such as the hydrogen embrittlement in ferritic steels, which motivated this work, and the Haber–Bosch process. We employed spin-polarised density functional theory to optimise geometries of a six-layer Fe slab, followed by frozen mode finite displacement phonon calculations to compute Fe–H vibrational frequencies. We have found that the quasi-threefold (3f) site is the most stable adsorption site, with adsorption energies of ∼3.0 eV/H for all coverages studied. The long-bridge (lb) site, which is close in energy to the 3f site, is actually a transition state leading to the stable 3f site. The calculated harmonic vibrational frequencies collectively span from 730 to 1220 cm{sup −1}, for a range of coverages. The increased first-to-second layer spacing in the presence of adsorbed hydrogen, and the pronounced buckling observed in the Fe surface layer, may facilitate the diffusion of hydrogen atoms into the bulk, and therefore impact the early stages of hydrogen embrittlement in steels.

  15. Relaxation and crystallization phenomena of water adsorbed to cellulose

    International Nuclear Information System (INIS)

    Czihak, Ch.; Mueller, M.; Schober, H.; Vogl, G.

    1999-01-01

    Complete text of publication follows. Cellulose, the most abundant biopolymer whose unit is D-anhydroglucose pyranose, has a tendency to adsorb water due to unsaturated hydroxyl groups in low ordered regions. This adsorbed water is present in the temperature range of 200 K < T < 273 K in different modifications. Due to voids and pores within and between the cellulose fibers, water molecules are able to build crystalline aggregations. Beyond that, water is able to penetrate the low ordered regions [1] and it adsorbs to cellulose chains. As introduced earlier in [2], the adsorbed water freezes to an amorphous like ice, while above T = 200 K an onset of relaxational motion on different time-scales (ns, ps) occurs. Recent neutron diffraction and INS data of water adsorbed to amorphous cellulose are shown as a new model system. Together with earlier experiments, the characteristics of relaxational motions are summarized and similarities to a glass transition of adsorbed water are discussed. (author) [1] J.M. Ioelovits and M. Gordeev, Acta Polymer. 45, 121-123 (1994); [2] J.C. Czihak, M. Mueller, H. Schober, L. Heux, G. Vogl, Physica B 266, 878-91. (1999)

  16. Efforts to Consolidate Chalcogels with Adsorbed Iodine

    Energy Technology Data Exchange (ETDEWEB)

    Riley, Brian J.; Pierce, David A.; Chun, Jaehun

    2013-08-28

    This document discusses ongoing work with non-oxide aerogels, called chalcogels, that are under development at the Pacific Northwest National Laboratory as sorbents for gaseous iodine. Work was conducted in fiscal year 2012 to demonstrate the feasibility of converting Sn2S3 chalcogel without iodine into a glass. This current document summarizes the work conducted in fiscal year 2013 to assess the consolidation potential of non-oxide aerogels with adsorbed iodine. The Sn2S3 and Sb13.5Sn5S20 chalcogels were selected for study. The first step in the process for these experiments was to load them with iodine (I2). The I2 uptake was ~68 mass% for Sn2S3 and ~50 mass% for Sb13.5Sn5S20 chalcogels. X-ray diffraction (XRD) of both sets of sorbents showed that metal-iodide complexes were formed during adsorption, i.e., SnI4 for Sn2S3 and SbI3 for Sb13.5Sn5S20. Additionally, metal-sulfide-iodide complexes were formed, i.e., SnSI for Sn2S3 and SbSI for Sb13.5Sn5S20. No XRD evidence for unreacted iodine was found in any of these samples. Once the chalcogels had reached maximum adsorption, the consolidation potential was assessed. Here, the sorbents were heated for consolidation in vacuum-sealed quartz vessels. The Sb13.5Sn5S20 chalcogel was heated both (1) in a glassy carbon crucible within a fused quartz tube and (2) in a single-containment fused quartz tube. The Sn2S3 chalcogel was only heated in a single-containment fused quartz tube. In both cases with the single-containment fused quartz experiments, the material consolidated nicely. However, in both cases, there were small fractions of metal iodides not incorporated into the final product as well as fused quartz particles within the melt due to the sample attacking the quartz wall during the heat treatment. The Sb13.5Sn5S20 did not appear to attack the glassy carbon crucible so, for future experiments, it would be ideal to apply a coating, such as pyrolytic graphite, to the inner walls of the fused quartz vessel to prevent

  17. Strong-coupling approximations

    International Nuclear Information System (INIS)

    Abbott, R.B.

    1984-03-01

    Standard path-integral techniques such as instanton calculations give good answers for weak-coupling problems, but become unreliable for strong-coupling. Here we consider a method of replacing the original potential by a suitably chosen harmonic oscillator potential. Physically this is motivated by the fact that potential barriers below the level of the ground-state energy of a quantum-mechanical system have little effect. Numerically, results are good, both for quantum-mechanical problems and for massive phi 4 field theory in 1 + 1 dimensions. 9 references, 6 figures

  18. Strong interaction and QFD

    International Nuclear Information System (INIS)

    Ebata, T.

    1981-01-01

    With an assumed weak multiplet structure for bosonic hadrons, which is consistent with the ΔI = 1/2 rule, it is shown that the strong interaction effective hamiltonian is compatible with the weak SU(2) x U(1) gauge transformation. Especially the rho-meson transforms as a triplet under SU(2)sub(w), and this is the origin of the rho-photon analogy. It is also shown that the existence of the non-vanishing Cabibbo angle is a necessary condition for the absence of the exotic hadrons. (orig.)

  19. Is the boundary layer of an ionic liquid equally lubricating at higher temperature?

    Science.gov (United States)

    Hjalmarsson, Nicklas; Atkin, Rob; Rutland, Mark W

    2016-04-07

    Atomic force microscopy has been used to study the effect of temperature on normal forces and friction for the room temperature ionic liquid (IL) ethylammonium nitrate (EAN), confined between mica and a silica colloid probe at 25 °C, 50 °C, and 80 °C. Force curves revealed a strong fluid dynamic influence at room temperature, which was greatly reduced at elevated temperatures due to the reduced liquid viscosity. A fluid dynamic analysis reveals that bulk viscosity is manifested at large separation but that EAN displays a nonzero slip, indicating a region of different viscosity near the surface. At high temperatures, the reduction in fluid dynamic force reveals step-like force curves, similar to those found at room temperature using much lower scan rates. The ionic liquid boundary layer remains adsorbed to the solid surface even at high temperature, which provides a mechanism for lubrication when fluid dynamic lubrication is strongly reduced. The friction data reveals a decrease in absolute friction force with increasing temperature, which is associated with increased thermal motion and reduced viscosity of the near surface layers but, consistent with the normal force data, boundary layer lubrication was unaffected. The implications for ILs as lubricants are discussed in terms of the behaviour of this well characterised system.

  20. Gold recovery from low concentrations using nanoporous silica adsorbent

    Science.gov (United States)

    Aledresse, Adil

    The development of high capacity adsorbents with uniform porosity denoted 5%MP-HMS (5% Mercaptopropyl-Hexagonal Mesoporous Structure) to extract gold from noncyanide solutions is presented. The preliminary studies from laboratory simulated noncyanide gold solutions show that the adsorption capacities of these materials are among the highest reported. The high adsorption saturation level of these materials, up to 1.9 mmol/g (37% of the adsorbent weight) from gold chloride solutions (potassium tetrachloroaurate) and 2.9 mmol/g (57% of the adsorbent weight) from gold bromide solutions (potassium tetrabromoaurate) at pH = 2, is a noteworthy feature of these materials. This gold loading from [AuC4]- and [AuBr4 ]- solutions corresponds to a relative Au:S molar ratio of 2.5:1 and 3.8:1, respectively. These rates are significantly higher than the usual 1:1 (Au:S) ratio expected for metal ion binding with the material. The additional gold ions loaded have been spontaneously reduced to metallic gold in the mesoporous material. Experimental studies indicated high maximum adsorptions of gold as high as 99.9% recovery. Another promising attribute of these materials is their favourable adsorption kinetics. The MP-HMS reaches equilibrium (saturation) in less than 1 minute of exposure in gold bromide and less than 10 minutes in gold chloride. The MP-HMS materials adsorption is significantly improved by agitation and the adsorption capacity of Au (III) ions increases with the decrease in pH. The recovery of adsorbed gold and the regeneration of spent adsorbent were investigated for MP-HMS adsorbent. The regenerated adsorbent (MP-HMS) maintained its adsorption capacity even after repeated use and all the gold was successfully recovered from the spent adsorbent. For the fist time, a promising adsorbent system has been found that is capable of effectively concentrating gold thiosulphate complexes, whereas conventional carbon-inpulp (CIP) and carbon-in-leach (CIL) systems fail. The

  1. Effect of shape and size of amidoxime-group-containing adsorbent on the recovery of uranium from sea water

    International Nuclear Information System (INIS)

    Omichi, H.; Kataki, A.; Sugo, T.; Okamoto, J.; Katoh, S.; Sakane, K.; Sugasaka, K.; Itagaki, T.

    1987-01-01

    An amidoxime-group-containing adsorbent for the recovery of uranium from sea water was synthesized by radiation-induced graft polymerization of acrylonitrile onto polypropylene fiber of round and cross-shaped sections. The tensile strength and elongation of the synthesized adsorbent, both of which were one-half those of the raw material, were not affected by the shape of the fiber. The deterioration of the adsorption ability induced by immersing the adsorbent in HCl was negligible because of the short immersion time required for the desorption with HCl. The concentration factors for uranium and transition metals in 28 days were in the order of 10 5 , while those for alkali metals and alkaline earth metals were in the order 10 -1 -10 1 . The recovery of uranium with the cross-shaped adsorbent was superior to that of the round-shaped one. XMA line profiles show that the distribution of uranium is much restricted to the surface layer when compared with that of alkaline earth metals. Diminishing the diameter or increasing the surface area was effective for increasing the adsorption of uranium

  2. Strong Plate, Weak Slab Dichotomy

    Science.gov (United States)

    Petersen, R. I.; Stegman, D. R.; Tackley, P.

    2015-12-01

    Models of mantle convection on Earth produce styles of convection that are not observed on Earth.Moreover non-Earth-like modes, such as two-sided downwellings, are the de facto mode of convection in such models.To recreate Earth style subduction, i.e. one-sided asymmetric recycling of the lithosphere, proper treatment of the plates and plate interface are required. Previous work has identified several model features that promote subduction. A free surface or pseudo-free surface and a layer of material with a relatively low strength material (weak crust) allow downgoing plates to bend and slide past overriding without creating undue stress at the plate interface. (Crameri, et al. 2012, GRL)A low viscosity mantle wedge, possibly a result of slab dehydration, decouples the plates in the system. (Gerya et al. 2007, Geo)Plates must be composed of material which, in the case of the overriding plate, are is strong enough to resist bending stresses imposed by the subducting plate and yet, as in the case of the subducting plate, be weak enough to bend and subduct when pulled by the already subducted slab. (Petersen et al. 2015, PEPI) Though strong surface plates are required for subduction such plates may present a problem when they encounter the lower mantle.As the subducting slab approaches the higher viscosity, lower mantle stresses are imposed on the tip.Strong slabs transmit this stress to the surface.There the stress field at the plate interface is modified and potentially modifies the style of convection. In addition to modifying the stress at the plate interface, the strength of the slab affects the morphology of the slab at the base of the upper mantle. (Stegman, et al 2010, Tectonophysics)Slabs that maintain a sufficient portion of their strength after being bent require high stresses to unbend or otherwise change their shape.On the other hand slabs that are weakened though the bending process are more amenable to changes in morphology. We present the results of

  3. Strong Coupling Holography

    CERN Document Server

    Dvali, Gia

    2009-01-01

    We show that whenever a 4-dimensional theory with N particle species emerges as a consistent low energy description of a 3-brane embedded in an asymptotically-flat (4+d)-dimensional space, the holographic scale of high-dimensional gravity sets the strong coupling scale of the 4D theory. This connection persists in the limit in which gravity can be consistently decoupled. We demonstrate this effect for orbifold planes, as well as for the solitonic branes and string theoretic D-branes. In all cases the emergence of a 4D strong coupling scale from bulk holography is a persistent phenomenon. The effect turns out to be insensitive even to such extreme deformations of the brane action that seemingly shield 4D theory from the bulk gravity effects. A well understood example of such deformation is given by large 4D Einstein term in the 3-brane action, which is known to suppress the strength of 5D gravity at short distances and change the 5D Newton's law into the four-dimensional one. Nevertheless, we observe that the ...

  4. Study on the adsorption performance of composite adsorbent of CaCl2 and expanded graphite with ammonia as adsorbate

    International Nuclear Information System (INIS)

    Li, S.L.; Wu, J.Y.; Xia, Z.Z.; Wang, R.Z.

    2009-01-01

    A novel constant volume test unit was built to study the adsorption performance of a new type composite adsorbent. This test unit can measure the adsorption isosteres of the working pairs. The adsorption isosteres are the curves of the adsorption pressure variation with the adsorption temperatures at constant adsorption quantities. Compared to the former test results of isothermals and isobars, the isosteres are better for the calculation of the adsorption heat, desorption heat and the selection the adsorption working pairs. Three experimental results were obtained: the first result was that the expanded graphite powders were superior to the expandable graphite powders to facilitate the transportation of working fluid in the composite adsorbent. The second one was that the composite adsorbent treated by solution is more homogeneous than the simple mixed composite adsorbent and the treated composite adsorbent has a better mass transfer performance. The last one was that the adsorption isosteres was the same one not only in the heating process but also in the cooling process and this performance was not relevant to the homogeneity of the composite adsorbent

  5. Equilibrium, kinetic and sorber design studies on the adsorption of Aniline blue dye by sodium tetraborate-modified Kaolinite clay adsorbent.

    Science.gov (United States)

    Unuabonah, Emmanuel I; Adebowale, Kayode O; Dawodu, Folasegun A

    2008-09-15

    Raw Kaolinite clay obtained Ubulu-Ukwu, Delta State of Nigeria and its sodium tetraborate (NTB)-modified analogue was used to adsorb Aniline blue dye. Fourier transformed infrared spectra of NTB-modified Kaolinite suggests that modification was effective on the surface of the Kaolinite clay with the strong presence of inner -OH functional group. The modification of Kaolinite clay raised its adsorption capacity from 1666 to 2000 mg/kg. Modeling adsorption data obtained from both unmodified and NTB-modified Kaolinite clay reveals that the adsorption of Aniline blue dye on unmodified Kaolinite clay is on heterogeneous adsorption sites because it followed strongly the Freundlich isotherm equation model while adsorption data from NTB-modified Kaolinite clay followed strongly the Langmuir isotherm equation model which suggest that Aniline blue dye was adsorb homogeneous adsorption sites on the NTB-modified adsorbent surface. There was an observed increase in the amount of Aniline blue adsorbed as initial dye concentration was increased from 10 to 30 mg/L. It was observed that kinetic data obtained generally gave better robust fit to the second-order kinetic model (SOM). The initial sorption rate was found to increased with increasing initial dye concentration (from 10 to 20 mg/L) for data obtained from 909 to 1111 mg kg(-1)min(-1) for unmodified and 3325-5000 mg kg(-1) min(-1) for NTB-modified adsorbents. Thereafter there was a decrease in initial sorption rate with further increase in dye concentration. The linearity of the plots of the pseudo-second-order model with very high-correlation coefficients indicates that chemisorption is involved in the adsorption process. From the design of a single-batch adsorber it is predicted that the NTB-modified Kaolinite clay adsorbent will require 50% less of the adsorbent to treat certain volumes of wastewater containing 30 mg/L of Aniline blue dye when it is compared with the unmodified adsorbent. This will be cost effective in

  6. LIGO: The strong belief

    CERN Multimedia

    Antonella Del Rosso

    2016-01-01

    Twenty years of designing, building and testing a number of innovative technologies, with the strong belief that the endeavour would lead to a historic breakthrough. The Bulletin publishes an abstract of the Courier’s interview with Barry Barish, one of the founding fathers of LIGO.   The plots show the signals of gravitational waves detected by the twin LIGO observatories at Livingston, Louisiana, and Hanford, Washington. (Image: Caltech/MIT/LIGO Lab) On 11 February, the Laser Interferometer Gravitational-Wave Observatory (LIGO) and Virgo collaborations published a historic paper in which they showed a gravitational signal emitted by the merger of two black holes. These results come after 20 years of hard work by a large collaboration of scientists operating the two LIGO observatories in the US. Barry Barish, Linde Professor of Physics, Emeritus at the California Institute of Technology and former Director of the Global Design Effort for the Internat...

  7. Bovine serum albumin adsorption on passivated porous silicon layers

    Science.gov (United States)

    Lockwood, David; Boukherroub, Rabah

    2005-03-01

    Hydrogen-terminated porous silicon (pSi) films were fabricated through electrochemical anodization of crystalline Si in HF-based solutions. The pSi-H surface was chemically functionalized by thermal reaction with undecylenic acid to produce an organic monolayer covalently attached to the silicon surface through Si-C bonds and bearing an acid terminal group. Bovine serum albumin (BSA) was then adsorbed onto the modified surface. SEM showed that the porous films were damaged and partially lifted off the Si substrate after a prolonged BSA adsorption. Ellipsometry revealed that the BSA had penetrated ˜ 1.3 micrometers into the porous structure. The film damage results from BSA anchoring itself tightly through strong electrostatic interactions to the acid-covered Si sidewalls. A change in surface tension during BSA film formation then causes the pSi layer to buckle and lift-off the underlying Si substrate. FTIR results from the modified pSi surfaces showed the presence of strong characteristic Amide I, II and III vibrational bands after BSA adsorption.

  8. Intramolecular charge separation in spirobifluorene-based donor–acceptor compounds adsorbed on Au and indium tin oxide electrodes

    International Nuclear Information System (INIS)

    Heredia, Daniel; Otero, Luis; Gervaldo, Miguel; Fungo, Fernando; Dittrich, Thomas; Lin, Chih-Yen; Chi, Liang-Chen; Fang, Fu-Chuan; Wong, Ken-Tsung

    2013-01-01

    Surface photovoltage (SPV) measurements were performed with a Kelvin-probe in spirobifluorene-based donor (diphenylamine)–acceptor (dicyano or cyanoacrylic acid moieties) compounds adsorbed from highly diluted solutions onto Au and indium tin oxide electrode surfaces. Strong intramolecular charge separation (negative SPV signals up to more than 0.1 V) due to directed molecule adsorption was observed only for spirobifluorene donor–acceptor compounds with carboxylic acid moiety. SPV signals and onset energies of electronic transitions depended on ambience conditions. - Highlights: ► Fluorene donor–acceptor derivatives were adsorbed at Au and indium tin oxide. ► Surface photovoltage measurements were performed with a Kelvin-probe. ► Strong intra-molecular charge separation was observed. ► SPV signals depended on ambience conditions

  9. Characterisation of phase transition in adsorbed monolayers at the air/water interface.

    Science.gov (United States)

    Vollhardt, D; Fainerman, V B

    2010-02-26

    Recent work has provided experimental and theoretical evidence that a first order fluid/condensed (LE/LC) phase transition can occur in adsorbed monolayers of amphiphiles and surfactants which are dissolved in aqueous solution. Similar to Langmuir monolayers, also in the case of adsorbed monolayers, the existence of a G/LE phase transition, as assumed by several authors, is a matter of question. Representative studies, at first performed with a tailored amphiphile and later with numerous other amphiphiles, also with n-dodecanol, provide insight into the main characteristics of the adsorbed monolayer during the adsorption kinetics. The general conditions necessary for the formation of a two-phase coexistence in adsorbed monolayers can be optimally studied using dynamic surface pressure measurements, Brewster angle microscopy (BAM) and synchrotron X-ray diffraction at grazing incidence (GIXD). A characteristic break point in the time dependence of the adsorption kinetics curves indicates the phase transition which is largely affected by the concentration of the amphiphile in the aqueous solution and on the temperature. Formation and growth of condensed phase domains after the phase transition point are visualised by BAM. As demonstrated by a tailored amphiphile, various types of morphological textures of the condensed phase can occur in different temperature regions. Lattice structure and tilt angle of the alkyl chains in the condensed phase of the adsorbed monolayer are determined using GIXD. The main growth directions of the condensed phase textures are correlated with the two-dimensional lattice structure. The results, obtained for the characteristics of the condensed phase after a first order main transition, are supported by experimental bridging to the Langmuir monolayers. Phase transition of adsorbing trace impurities in model surfactants can strongly affect the characteristics of the main component. Dodecanol present as minor component in aqueous sodium

  10. Structural and magnetic studies on heavy-metal-adsorbing iron sulphide nanoparticles produced by sulphate-reducing bacteria

    International Nuclear Information System (INIS)

    Watson, J.H.P; Cressey, B.A.; Roberts, A.P.; Ellwood, D.C.; Charnock, J.M.; Soper, A.K.

    2000-01-01

    In previous and in work to be published, it has been shown that iron sulphide material, produced by sulphate-reducing bacteria (SRB), is an excellent adsorbent for a wide range of heavy metals. The material adsorbs between 100 and 400 mg g -1 and residual levels in solutions can be of the order of pg per litre. Further, strongly magnetic forms of this material can now be produced which can be effectively and cheaply removed from suspension together with the adsorbate by magnetic separation. This paper examines the structure of weakly magnetic and strongly magnetic iron sulphide material produced by SRB with a view to increasing the understanding of its adsorbent and the magnetic properties. The structural properties have been examined using high-resolution imaging and electron diffraction in a transmission electron microscope (TEM), the measurements of magnetisation versus field and temperature, extended X-ray absorption fine-structure (EXAFS) spectroscopy, X-ray absorption near-edge structure (XANES) spectroscopy and neutron diffraction. Before drying the surface area of both the weakly magnetic and the strongly magnetic iron sulphide is of the order of 400-500 m 2 g -1 as revealed by the magnetic properties, neutron scattering and the adsorption of a number of heavy metals. After freeze-drying the surface area falls to between 18 and 19 m 2 g -1 . The initial inocula came from a semi-saline source and when fed with nutrient containing Fe 2+ and Fe 3+ produced a weakly magnetic iron sulphide (Watson et al., Minerals Eng. 8 (1995) 1097) and a few % of a more strongly magnetic material. Further work using a novel method (Keller-Besrest, Collin, J. Solid State Chem. 84 (1990) 211) produced a strongly magnetic iron sulphide material. EXAFS and XANES spectroscopy revealed (Keller-Besrest and Collin, 1990) that the weakly magnetic iron sulphide material had the Ni-As structure in which the Fe is tetrahedrally coordinated with the composition Fe 1-x S. The strongly

  11. Frictional Coulomb drag in strong magnetic fields

    DEFF Research Database (Denmark)

    Bønsager, Martin Christian; Flensberg, Karsten; Hu, Ben Yu-Kuang

    1997-01-01

    A treatment of frictional Coulomb drag between two two-dimensional electron layers in a strong perpendicular magnetic field, within the independent electron picture, is presented. Assuming fully resolved Landau levels, the linear response theory expression for the transresistivity rho(21) is eval......A treatment of frictional Coulomb drag between two two-dimensional electron layers in a strong perpendicular magnetic field, within the independent electron picture, is presented. Assuming fully resolved Landau levels, the linear response theory expression for the transresistivity rho(21......) is evaluated using diagrammatic techniques. The transresistivity is given by an integral over energy and momentum transfer weighted by the product of the screened interlayer interaction and the phase space for scattering events. We demonstrate, by a numerical analysis of the transresistivity, that for well...

  12. Stability constants for silicate adsorbed to ferrihydrite

    DEFF Research Database (Denmark)

    Hansen, Hans Christian Bruun; Wetche, T.P.; Raulund-Rasmussen, Karsten

    1994-01-01

    Intrinsic surface acidity constants (K(a1)intr, K(a2)intr) and surface complexation constant for adsorption of orthosilicate onto synthetic ferrihydrite (K(Si) for the complex = FeOSi(OH)3) have been determined from acid/base titrations in 0.001-0.1 m NaClO4 electrolytes and silicate adsorption...... experiments in 0.01 m NaNO3 electrolyte (pH 3-6). The surface equilibrium constants were calculated according to the two-layer model by Dzombak & Morel (1990). Near equilibrium between protons/hydroxyls in solution and the ferrihydrite surface was obtained within minutes while equilibration with silicate...

  13. In-situ probing of coupled atomic restructuring and metallicity of oxide heterointerfaces induced by polar adsorbates

    Energy Technology Data Exchange (ETDEWEB)

    Ryu, S. [Department of Materials Science and Engineering, University of Wisconsin-Madison, Madison, Wisconsin 53706, USA; Zhou, H. [X-ray Science Division, Argonne National Laboratory, Argonne, Illinois 60439, USA; Paudel, T. R. [Department of Physics and Astronomy, University of Nebraska, Lincoln, Nebraska 68588, USA; Irwin, J. [Department of Physics, University of Wisconsin-Madison, Madison, Wisconsin 53706, USA; Podkaminer, J. P. [Department of Materials Science and Engineering, University of Wisconsin-Madison, Madison, Wisconsin 53706, USA; Bark, C. W. [Department of Materials Science and Engineering, University of Wisconsin-Madison, Madison, Wisconsin 53706, USA; Lee, D. [Department of Materials Science and Engineering, University of Wisconsin-Madison, Madison, Wisconsin 53706, USA; Kim, T. H. [Department of Materials Science and Engineering, University of Wisconsin-Madison, Madison, Wisconsin 53706, USA; Fong, D. D. [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439, USA; Rzchowski, M. S. [Department of Physics, University of Wisconsin-Madison, Madison, Wisconsin 53706, USA; Tsymbal, E. Y. [Department of Physics and Astronomy, University of Nebraska, Lincoln, Nebraska 68588, USA; Eom, C. B. [Department of Materials Science and Engineering, University of Wisconsin-Madison, Madison, Wisconsin 53706, USA

    2017-10-02

    Microscopic understanding of the surface-controlled conductivity of the two dimensional electron gas at complex oxide interfaces is crucial for developing functional interfaces. We observe conductivity and structural modification using in-situ synchrotron surface x-ray diffraction as the surface of a model LaAlO3/SrTiO3 (001) heterostructure is changed by polar adsorbates. We find that polar adsorbate-induced interfacial metallicity reduces polar distortions in the LaAlO3 layer. First-principles density functional theory calculations show that surface dipoles introduced by polar adsorbates lead to additional charge transfer and the reduction of polar displacements in the LaAlO3 layer, consistent with the experimental observations. Our study supports that internal structural deformations controlling functionalities can be driven without the application of direct electrical or thermal bias and offers a route to tuning interfacial properties. These results also highlight the important role of in-situ x-ray scattering with atomic resolution in capturing and exploring structural distortions and charge density changes caused by external perturbations such as chemical adsorption, redox reaction, and generation and/or annihilation of surface defects.

  14. Disorder and transport of silver in some layered metal sulfides

    NARCIS (Netherlands)

    Gerards, Anthonius Gijsbertus

    1987-01-01

    The chemical and physical properties of compounds with a layered structure are strongly determined by the two-dimensional nature of the bonding, viz. strong bonding within the layers and much weaker bonds between the layers; graphite is an example of such and anisotropic solid. the layered

  15. John Strong (1941 - 2006)

    CERN Multimedia

    Wickens, F

    Our friend and colleague John Strong was cruelly taken from us by a brain tumour on Monday 31st July, a few days before his 65th birthday John started his career working with a group from Westfield College, under the leadership of Ted Bellamy. He obtained his PhD and spent the early part of his career on experiments at Rutherford Appleton Laboratory (RAL), but after the early 1970s his research was focussed on experiments in CERN. Over the years he made a number of notable contributions to experiments in CERN: The Omega spectrometer adopted a system John had originally developed for experiments at RAL using vidicon cameras to record the sparks in the spark chambers; He contributed to the success of NA1 and NA7, where he became heavily involved in the electronic trigger systems; He was responsible for the second level trigger system for the ALEPH detector and spent five years leading a team that designed and built the system, which ran for twelve years with only minor interventions. Following ALEPH he tur...

  16. Stirring Strongly Coupled Plasma

    CERN Document Server

    Fadafan, Kazem Bitaghsir; Rajagopal, Krishna; Wiedemann, Urs Achim

    2009-01-01

    We determine the energy it takes to move a test quark along a circle of radius L with angular frequency w through the strongly coupled plasma of N=4 supersymmetric Yang-Mills (SYM) theory. We find that for most values of L and w the energy deposited by stirring the plasma in this way is governed either by the drag force acting on a test quark moving through the plasma in a straight line with speed v=Lw or by the energy radiated by a quark in circular motion in the absence of any plasma, whichever is larger. There is a continuous crossover from the drag-dominated regime to the radiation-dominated regime. In the crossover regime we find evidence for significant destructive interference between energy loss due to drag and that due to radiation as if in vacuum. The rotating quark thus serves as a model system in which the relative strength of, and interplay between, two different mechanisms of parton energy loss is accessible via a controlled classical gravity calculation. We close by speculating on the implicati...

  17. Strong-interaction nonuniversality

    International Nuclear Information System (INIS)

    Volkas, R.R.; Foot, R.; He, X.; Joshi, G.C.

    1989-01-01

    The universal QCD color theory is extended to an SU(3) 1 direct product SU(3) 2 direct product SU(3) 3 gauge theory, where quarks of the ith generation transform as triplets under SU(3)/sub i/ and singlets under the other two factors. The usual color group is then identified with the diagonal subgroup, which remains exact after symmetry breaking. The gauge bosons associated with the 16 broken generators then form two massive octets under ordinary color. The interactions between quarks and these heavy gluonlike particles are explicitly nonuniversal and thus an exploration of their physical implications allows us to shed light on the fundamental issue of strong-interaction universality. Nonuniversality and weak flavor mixing are shown to generate heavy-gluon-induced flavor-changing neutral currents. The phenomenology of these processes is studied, as they provide the major experimental constraint on the extended theory. Three symmetry-breaking scenarios are presented. The first has color breaking occurring at the weak scale, while the second and third divorce the two scales. The third model has the interesting feature of radiatively induced off-diagonal Kobayashi-Maskawa matrix elements

  18. Neutron activation analysis for the characterization of seawater uranium adsorbents.

    Science.gov (United States)

    Byers, M; Landsberger, S; Schneider, E; Eder, S

    2018-03-01

    This work details the development of an iterative neutron activation analysis (NAA) based workflow to precisely quantify metal ion uptake in an adsorbent. The workflow is iterative because it explores the dependence between independent variables defining the adsorbent fabrication procedure and the time-dependent uptake. It can be adapted to other adsorbents provided they have an affinity for ions which are amenable to efficient quantification using NAA. For this work, the ability of silver nanoparticles to mitigate the negative effects of biofouling on uranium transfer to an adsorbent was ultimately of interest, and hence motivates the development of this method. The limits of U detection and quantification were found to be 0.609 and 3.01μgg -1 , respectively; these were obtained using modest irradiation and counting times. The uncertainties arising from the NAA procedure were no more than 9.9%, far smaller than other sources of uncertainty present in the analysis. These results provided solid evidence that adsorbent shape and structure, rather than uniformity of composition, drives variability in adsorption of uranium. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Recycling Spent Cr Adsorbents as Catalyst for Eliminating Methylmercaptan.

    Science.gov (United States)

    He, Dedong; Zhang, Liming; Zhao, Yutong; Mei, Yi; Chen, Dingkai; He, Sufang; Luo, Yongming

    2018-03-20

    Waste adsorbents generated from treating Cr(VI)-containing wastewater are hazardous materials and generally landfilled or treated by acid or base desorption, with concomitant high cost and toxic effects. The present work shows that these Cr adsorbents can be reused as highly efficient catalysts for treating sulfur-containing VOCs (CH 3 SH), not only avoiding the economic and environmental impact from the conventional approaches, but also achieving the efficient treatment of sulfur-containing waste gas. Importantly, these reused Cr adsorbents exhibit enhanced activity and stability compared with the catalysts reported elsewhere, indicating a new avenue of green chemistry. The highly toxic adsorbed Cr(VI) species are reduced to a Cr 2 O 3 crystalline phase by calcination and finally immobilized as a Cr 2 S 3 solid phase while converting and eliminating CH 3 SH. Still, the presence of Cr(VI) species on the reused Cr adsorbent provides enough reactive sites for reaction, but high concentration of Cr(VI) species causes serious accumulation of coke deposit on the catalyst, leading to fast deactivation of the catalyst.

  20. Lipid monolayers and adsorbed polyelectrolytes with different degrees of polymerization.

    Science.gov (United States)

    Ortmann, Thomas; Ahrens, Heiko; Lawrenz, Frank; Gröning, Andreas; Nestler, Peter; Günther, Jens-Uwe; Helm, Christiane A

    2014-06-17

    Polystyrene sulfonate (PSS) of different molecular weight M(w) is adsorbed to oppositely charged DODAB monolayers from dilute solutions (0.01 mmol/L). PSS adsorbs flatly in a lamellar manner, as is shown by X-ray reflectivity and grazing incidence diffraction (exception: PSS with M(w) below 7 kDa adsorbs flatly disordered to the liquid expanded phase). The surface coverage and the separation of the PSS chains are independent of PSS M(w). On monolayer compression, the surface charge density increases by a factor of 2, and the separation of the PSS chains decreases by the same factor. Isotherms show that on increase of PSS M(w) the transition pressure of the LE/LC (liquid expanded/liquid condensed) phase transition decreases. When the contour length exceeds the persistence length (21 nm), the transition pressure is low and constant. For low-M(w) PSS (<7 kDa) the LE/LC transition of the lipids and the disordered/ordered transition of adsorbed PSS occur simultaneously, leading to a maximum in the contour length dependence of the transition enthalpy. These findings show that lipid monolayers at the air/water interface are a suitable model substrate with adjustable surface charge density to study the equilibrium conformation of adsorbed polyelectrolytes as well as their interactions with a model membrane.

  1. Bio-polishing sludge adsorbents for dye removal

    Directory of Open Access Journals (Sweden)

    Zaini Muhammad Abbas Ahmad

    2016-12-01

    Full Text Available The objective of this work is to evaluate the removal of methylene blue dye by bio-polishing sludge-based adsorbents. The adsorbents were characterized according to the specific surface area, pH upon the treatment and surface functional groups. The adsorption of dye was carried out at room temperature, and the adsorption data were analyzed using the isotherm and kinetics models. The bio-polishing sludge is rich in ash content, and the presence of surface functional groups varied with the treatment strategies. The specific surface area of adsorbents is between 7.25 and 20.8 m2/g. Results show that the maximum removal of methylene blue by sludge adsorbents was observed to have the following order: untreated sludge (SR > zinc chloride-treated (SZ > microwave-dried (SW = potassium carbonate-treated (SK > acid-washed (SH. The maximum adsorption capacities for SR and SZ as predicted by the Langmuir model are 170 and 135 mg/g, respectively. Although SR demonstrates a higher maximum removal than SZ, the latter exhibits greater removal intensity and rate constant even at high dye concentration. The bio-polishing sludge is a promising adsorbent for dye wastewater treatment.

  2. Development of nanohybrid adsorbent for defluoridation from aqueous systems.

    Science.gov (United States)

    Dhongde, Vicky; Wasewar, Kailas L; De, Biswajit S

    2017-12-01

    The objective of present study is advancement of an efficient nanomaterial which was investigated to substantiate its efficiency, using kinetic studies to ensnare fluoride in order to make water potable. A new crystalline ZrAlCa nanohybrid adsorbent for fluoride removal was successfully synthesized by a co-precipitation method in this study. The prepared adsorbents were characterized by XRD, FT-IR, TGA, BET and FESEM and EDX. The adsorption properties of the developed adsorbent were studied using batch adsorption method which shown the noticeable fluoride removal efficiency up to 99% at near neutral pH as well as in acidic pH range. The reaction kinetics for adsorption of fluoride was established using reaction based kinetic models which fitted well with Avarami kinetic model as compared to pseudo-first-order, pseudo second-order and power function rate expression. The equilibrium isotherm modelling described adsorption process and Langmuir, Jovanovic, Temkin and Freundlich isotherms provides best fit to experimental data. The fluoride loaded adsorbent was efficiently regenerated by using an alkali solution and has no significant counter ion effect on fluoride adsorption efficiency. Interestingly, the developed nanomaterial has fluoride removal efficacy over varied concentration ranges. It has capability of reanimate and reuse the nanohybrid adsorbent makes it an attractive sustainable material. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Adsorption behavior of lithium from seawater using manganese oxide adsorbent

    International Nuclear Information System (INIS)

    Wajima, Takaaki; Munakata, Kenzo; Uda, Tatsuhiko

    2012-01-01

    The deuterium-tritium (D-T) fusion reactor system is expected to provide the main source of electricity in the future. Large amounts of lithium will be required, dependent on the reactor design concept, and alternative resources should be found to provide lithium inventories for nuclear fusion plants. Seawater has recently become an attractive source of this element and the separation and recovery of lithium from seawater by co-precipitation, solvent extraction and adsorption have been investigated. Amongst these techniques, the adsorption method is suitable for recovery of lithium from seawater, because certain inorganic ion-exchange materials, especially spinel-type manganese oxides, show extremely high selectivity for the lithium ion. In this study, we prepared a lithium adsorbent (HMn 2 O 4 ) by elution of spinel-type lithium di-manganese-tetra-oxide (LiMn 2 O 4 ) and examined the kinetics of the adsorbent for lithium ions in seawater using a pseudo-second-order kinetic model. The intermediate, LiMn 2 O 4 , can be synthesized from LiOH·H 2 O and Mn 3 O 4 , from which the lithium adsorbent can subsequently be prepared via acid treatment., The adsorption kinetics become faster and the amount of lithium adsorbed on the adsorbent increases with increasing solution temperature. The thermodynamic values, ΔG 0 , ΔH 0 and ΔS 0 , indicate that adsorption is an endothermic and spontaneous process. (author)

  4. Microporous carbonaceous adsorbents for CO2 separation via selective adsorption

    KAUST Repository

    Zhao, Yunfeng

    2015-01-01

    Selective adsorption of CO2 has important implications for many energy and environment-related processes, which require the separation of CO2 from other gases (e.g. N2 and CH4) with high uptakes and selectivity. The development of high-performance adsorbents is one of the most promising solutions to the success of these processes. The present review is focused on the state-of-the-art of carbon-based (carbonaceous) adsorbents, covering microporous inorganic carbons and microporous organic polymers, with emphasis on the correlation between their textural and compositional properties and their CO2 adsorption/separation performance. Special attention is given to the most recently developed materials that were not covered in previous reviews. We summarize various effective strategies (N-doping, surface functionalization, extra-framework ions, molecular design, and pore size engineering) for enhancing the CO2 adsorption capacity and selectivity of carbonaceous adsorbents. Our discussion focuses on CO2/N2 separation and CO2/CH4 separation, while including an introduction to the methods and criteria used for evaluating the performance of the adsorbents. Critical issues and challenges regarding the development of high-performance adsorbents as well as some overlooked facts and misconceptions are also discussed, with the aim of providing important insights into the design of novel carbonaceous porous materials for various selective adsorption based applications. This journal is © The Royal Society of Chemistry.

  5. Photophysics of Auramine O adsorbed on solid clays

    Energy Technology Data Exchange (ETDEWEB)

    Valandro, Silvano R.; Poli, Alessandra L.; Neumann, Miguel G.; Schmitt, Carla C., E-mail: carla@iqsc.usp.br

    2015-05-15

    The dye loading effect on the photophysical behavior of Auramine O adsorbed onto solid clays was studied. When the dye concentration is increased, solid samples of Auramine O incorporated in SYn-1, SAz-1 and SWy-1 clays show an enhancement of the β-band in the UV–vis-DR spectra and the band at 450 nm shifts to the blue. This behavior can be attributed to the formation of H-type dye aggregates. For SYn-1 and SAz-1 clays, which show higher charge density, the formation of H-aggregates of the dye is favored. The fluorescence intensity and lifetime values of AuO decrease with the increasing of dye loading in these clays, since H aggregates do not exhibit fluorescence. The basal spacing of SAz-1 and SYn-1 containing 5% of AuO remains the same as that for pure SAz-1 and SYn-1. The adsorption of the dye predominantly occurs on the external surface of the SAz-1 and SYn-1 clays. On the other hand, for SWy-1 clay, UV–vis results suggest the presence of H- and J- aggregates. The fluorescence emission and lifetimes increase with the AuO concentration. XRD measurements confirm the penetration of the Auramine O into interlayer regions of the SWy-1 clay. When the Auramine is in the interlamellar regions of clay, the rotation of its phenyl rings is restricted, diminishing the internal conversion rate, therefore increasing the emission. The adsorption of the dye occurs on the external surface and in the interlamellar layers of SWy-1. - Highlights: • AuO incorporated in SYn-1, SAz-1 and SWy-1 shows formation of H-aggregates. • The formation of H-aggregates of the dye is favored in SYn-1 and SAz-1 clays. • Adsorption of the dye occurs on the external surface of SAz-1 and SYn-1. • Auramine O penetrates into the interlayer regions of the SWy-1. • Fluorescence emission increases for AuO in the interlayer regions.

  6. Calculation of growth per cycle (GPC) of atomic layer deposited ...

    Indian Academy of Sciences (India)

    2014-03-06

    -k) materials as the gate oxide of MOSFET [1–3]. Aluminium oxide prepared by atomic ... adsorbed on to the substrate/previous layer in a saturating fashion. Argon/nitrogen is pulsed into the chamber to purge out any unreacted ...

  7. Morphology of self assembled monolayers using liquid phase reaction on silica and their effect on the morphology of adsorbed insulin

    Science.gov (United States)

    Sharma, Indu; Pattanayek, Sudip K.; Aggarwal, Varsha; Ghosh, Subhasis

    2017-05-01

    The effect of roughness of two different categories of self-assembled monolayers (SAMs) with propyl amine and propyl groups respectively on the morphology of adsorbed insulin is observed. SAMs are obtained by liquid phase reaction of silica with organo silane coupling agents (SCA). The influence of the morphology and physical characteristics of the SAMs on the reaction time and concentration of the modifiers are explored. We have tested three SCA containing propyl amine with varying groups linked to Si present on it. In addition, we have used a silane coupling agent to prepare SAM of methyl head group. The approach of these molecules towards the surface depends on the head group and the groups linked to Si of the SCA. The morphology of the surfaces is analysed using power spectral density distribution (PSD), skewness, ellipsometry thickness and surface energy. Both chemical nature and physical morphology of the adsorbent influence the morphology of the adsorbed insulin. In general, a low number of aggregates of big size are formed on the surfaces obtained from low concentration of SAMs, while a higher number but of smaller size of aggregates are formed over surfaces obtained from 1% concentration of SAMs modifiers. The peak to valley ratio of the aggregates of insulin is strongly influenced by the size of grains of SCA over the adsorbent.

  8. Adsorption of divalent copper, zinc, cadmium and lead ions from aqueous solution by waste tea and coffee adsorbents.

    Science.gov (United States)

    Djati Utomo, H; Hunter, K A

    2006-01-01

    The adsorption of the divalent cations of Cu, Zn, Cd and Pb by tea leaves and coffee grounds from aqueous solutions is described. Both adsorbents exhibited strong affinity for these ions which could be described by a simple single-site equilibrium model. For coffee, the order of increasing adsorption equilibrium constant K was Cu 10, probably because of anion formation in the case of Zn2+ and also increased leaching of metal-binding soluble materials. The effect of metal ion concentration on the adsorptive equilibria indicated a threshold concentration above which overall adsorption became limited by saturation of the adsorption sites. Competition between two metal ions for the same sites was not observed with Cu(II) and Pb(II), however Zn(II) reacted competitively with Cd(II) binding sites on both tea and coffee. If fresh coffee or tea adsorbents were used, the fraction of metal ion taken up by the adsorbent was diminished by the competitive effects of soluble metal-binding ligands released by the tea or coffee. Experiments with coffee showed that roasting temperature controls the formation of metal ion adsorption sites for this adsorbent.

  9. Rheology of Confined Polymer Melts under Shear Flow : Strong Adsorption Limit

    NARCIS (Netherlands)

    Subbotin, A.; Manias, E.; Hadziioannou, G.; Brinke, G. ten

    1995-01-01

    The dynamics of a confined polymer melt between strong adsorbing surfaces is considered theoretically. In particular the influence of bridging on the theological behavior is investigated. It is shown that the bridges are very important for small enough shear velocities. Several regimes of

  10. A Novel Oxidation-Reduction Route for Layer-by-Layer Synthesis of TiO2 Nanolayers and Investigation of Its Photocatalytical Properties

    Directory of Open Access Journals (Sweden)

    Konstantin Semishchenko

    2014-01-01

    Full Text Available Layer-by-layer (LbL synthesis of titanium dioxide was performed by an oxidation-reduction route using a Ti(OH3 colloid and NaNO2 solutions. A model of chemical reactions was proposed based on the results of an investigation of synthesized nanolayers by scanning electron microscopy, electron microprobe analysis and X-ray photoelectron spectroscopy, and studying colloidal solution of Ti(OH3 with laser Doppler microelectrophoresis. At each cycle, negatively charged colloidal particles of [Ti(OH3]HSO4- adsorbed onto the surface of substrate. During the next stage of treatment in NaNO2 solution, the particles were oxidized to Ti(OH4. Photocatalytic activity was studied by following decomposition of methylene blue (MB under UV irradiation. Sensitivity of the measurements was increased using a diffuse transmittance (DT method. The investigation revealed strong photocatalytical properties of the synthesized layers, caused by their high area per unit volume and uniform globular structure.

  11. Determinants of protein elution rates from preparative ion-exchange adsorbents.

    Science.gov (United States)

    Angelo, James M; Lenhoff, Abraham M

    2016-04-01

    The rate processes involved in elution in preparative chromatography can affect both peak resolution and hence selectivity as well as practical factors such as facility fit. These processes depend on the physical structure of the adsorbent particles, the amount of bound solute, the solution conditions for operation or some combination of these factors. Ion-exchange adsorbents modified with covalently attached or grafted polymer layers have become widely used in preparative chromatography. Their often easily accessible microstructures offer substantial binding capacities for biomolecules, but elution has sometimes been observed to be undesirably slow. In order to determine which physicochemical phenomena control elution behavior, commercially available cellulosic, dextran-grafted and unmodified agarose materials were characterized here by their elution profiles at various conditions, including different degrees of loading. Elution data were analyzed under the assumption of purely diffusion-limited control, including the role of pore structure properties such as porosity and tortuosity. In general, effective elution rates decreased with the reduction of accessible pore volume, but differences among different proteins indicated the roles of additional factors. Additional measurements and analysis, including the use of confocal laser scanning microscopy to observe elution within single chromatographic particles, indicated the importance of protein association within the particle during elution. The use of protein stabilizing agents was explored in systems presenting atypical elution behavior, and l-arginine and disaccharide excipients were shown to alleviate the effects for one protein, lysozyme, in the presence of sodium chloride. Incorporation of these excipients into eluent buffer gave rise to faster elution and significantly lower pool volumes in elution from polymer-modified adsorbents. Copyright © 2016 Elsevier B.V. All rights reserved.

  12. On the physics of relativistic double layers

    International Nuclear Information System (INIS)

    Carlqvist, P.

    1982-06-01

    A model of a strong, time-independent, and relativistic double layer is studied. Besides double layers having the electric field parallel to the current the model also describes a certain type of oblique double layers. The 'Langmuir condition' (ratio of ion current density to electron current density) as well as an expression for the potential drop of the double layer are derived. Furthermore, the distribution of charged particles, electric field, and potential within the double layer are clarified and discussed. It is found that the properties of relativistic double layers differ substantially from the properties of corresponding non-relativistic double layers. (Author)

  13. Method of recovering adsorbed liquid compounds from molecular sieve columns

    Science.gov (United States)

    Burkholder, Harvey R.; Fanslow, Glenn E.

    1983-01-01

    Molecularly adsorbed volatile liquid compounds are recovered from molecular sieve adsorbent columns by directionally applying microwave energy to the bed of the adsorbent to produce a mixed liquid-gas effluent. The gas portion of the effluent generates pressure within the bed to promote the discharge of the effluent from the column bottoms. Preferably the discharged liquid-gas effluent is collected in two to three separate fractions, the second or intermediate fraction having a substantially higher concentration of the desorbed compound than the first or third fractions. The desorption does not need to be assisted by passing a carrier gas through the bed or by applying reduced pressure to the outlet from the bed.

  14. Quantitative relationship between adsorbed amount of solute and solvent composition

    International Nuclear Information System (INIS)

    Wang Yan; Geng Xindu; Zebolsky, Don M.

    2003-01-01

    A new adsorption isotherm that relates the amount of solute adsorbed to the solvent concentration is proposed. The new equation is derived from Geng and Shi's stoichiometric displacement model for adsorption (SDM-A). The obtained equation may be simplified to an expression containing two parameters. The equation with two parameters, valid for low concentrations of solute, is a logarithmically linear relationship. The intercept contains a thermodynamic equilibrium constant of the solute displacing solvent from the adsorbent. The slope is the negative value of the stoichiometric displacement parameter (Z), the average total number of solvent molecules displaced from an active site on the adsorbent and from the solute. Tests with a homologous series of aromatic alcohols by frontal analysis in reversed phase liquid chromatography demonstrate that experimental results fit the equation well

  15. Lotus Dust Mitigation Coating and Molecular Adsorber Coating

    Science.gov (United States)

    O'Connor, Kenneth M.; Abraham, Nithin S.

    2015-01-01

    NASA Goddard Space Flight Center has developed two unique coating formulations that will keep surfaces clean and sanitary and contain contaminants.The Lotus Dust Mitigation Coating, modeled after the self-cleaning, water-repellant lotus leaf, disallows buildup of dust, dirt, water, and more on surfaces. This coating, has been successfully tested on painted, aluminum, glass, silica, and some composite surfaces, could aid in keeping medical assets clean.The Molecular Adsorber Coating is a zeolite-based, sprayable molecular adsorber coating, designed to prevent outgassing in materials in vacuums. The coating works well to adsorb volatiles and contaminates in manufacturing and processing, such as in pharmaceutical production. The addition of a biocide would also aid in controlling bacteria levels.

  16. Adsorption performance of magnesium/aluminum layered double hydroxide nanoparticles for metronidazole from aqueous s

    Directory of Open Access Journals (Sweden)

    Mohammad Noori Sepehr

    2017-07-01

    Full Text Available Magnesium/aluminum layered double hydroxide (LDH nanoparticles were synthesized by hydrolyzing urea and used to remove metronidazole (MN from aqueous solution. The surface morphology images of the LDH nanoparticles showed that the adsorbent surface consisted of hexagonal nanosheets with a diameter of 200–1000 nm. The MN removal efficiency was strongly dependent on the solution pH ranging from 3 to 9. The addition of nitrate, sulfate, and carbonate did not remarkably affect MN adsorption, while hardness slightly improved MN removal efficiency. The adsorption isotherm data could be well described using the Sips equation. The analysis of kinetic data showed that the adsorption of MN onto LDH closely followed the Avrami model and that several kinetic processes may control the rate of sorption. The adsorption process was non-spontaneous and exothermic in nature. The maximum Langmuir adsorption capacity was 62.804 mg/g, demonstrating that LDH is an efficient adsorbent that can be used for the removal of MN compounds.

  17. DFT studies of the interactions of a graphene layer with small water aggregates.

    Science.gov (United States)

    Freitas, R R Q; Rivelino, R; Mota, F de Brito; de Castilho, C M C

    2011-11-10

    We have investigated the structure, adsorption, electronic states, and charge transfer of small water aggregates on the surface of a graphene layer using density functional theory. Our calculations were focused on water adsorbates containing up to five water molecules interacting with one and both sides of a perfect freestanding sheet. Different orientations of the aggregates with respect to the graphene sites were considered. The results show that the adsorption energy of one water molecule is primarily determined by its orientation, although it is also strongly dependent on the implemented functional scheme. Despite its intrinsic difficulties with dispersion interactions, the Perdew and Wang's exchange-correlation functional may be a viable alternative to investigate the adsorption of large molecular aggregates on a graphene surface. Although water physisorption is expected to occur in the regime of droplets, we found no induced impurity states close to the Fermi level of graphene interacting with small water clusters. In order to investigate the donor/acceptor tendency of the water clusters on graphene, we have performed a Bader charge analysis. Considering the charge transfer mechanism, we have noticed that it should preferentially occur from water to graphene only when the oxygen atom is pointing toward the surface. Otherwise, and in the case of larger adsorbed clusters, charge transfers systematically occur from graphene to water.

  18. A new adsorbent for boron removal from aqueous solutions.

    Science.gov (United States)

    Kluczka, Joanna; Korolewicz, Teofil; Zołotajkin, Maria; Simka, Wojciech; Raczek, Malwina

    2013-01-01

    A new adsorbent based on natural clinoptilolite and amorphous zirconium dioxide (ZrO2) was prepared for the uptake of boron from fresh water. The sorption behaviour of this adsorbent for boron was investigated using a batch system and found to obey Langmuir, Freundlich and Dubinin-Radushkevich (D-R) isotherm models. The ZrO2 loading level, pH, temperature, contact time, initial boron concentration and adsorbent dose, on the removal of boron were studied. It was found that the removal of boron increased while the adsorbent dose increased and the temperature decreased at an optimum pH (pH = 8) and a contact time of 30 min. At optimum conditions, the maximum boron percentage removal was 75%. According to the D-R model, the maximum capacity was estimated to be > 3 mg B/g of the adsorbent. The adsorption energy value (calculated as 9.13 kJ/mol) indicated that the adsorption of boron on clinoptilolite modified with ZrO2 was physical in nature. The parameters of the adsorption models and the pH investigations pointed to the possibility of a chemisorption process. The thermodynamic parameters (standard entropy deltaS degrees, enthalpy deltaH degrees , and free energy deltaG degrees changes) of boron adsorption were also calculated. The negative value of deltaS degrees indicated a decreased randomness at the solid-solution interface during the boron adsorption. Negative values of deltaH degrees showed the exothermic nature of the process. The negative values of deltaG degrees implied that the adsorption of boron on clinoptilolite modified with amorphous ZrO2 at 25 degrees C was spontaneous. It was considered that boron dissolved in water had been adsorbed both physically and chemically on clinoptilolite modified with 30% ZrO2.

  19. A model for sound propagation between two adsorbing microporous plates.

    Science.gov (United States)

    Nori, Massimiliano; Brandani, Stefano

    2014-05-01

    A model describing the sound propagation between two infinite adsorbing plates is proposed in order to investigate the extension to the audible sound range of the Frequency Response method applied to the measurement of diffusion in micropores. The model relates adsorption parameters (i.e., diffusivity and equilibrium constant) to an acoustic quantity (i.e., propagation constant). The equations describing sound propagation in the presence of adsorbing boundaries are obtained on the basis of the classical Kirchhoff theory [(1868). Ann. Phys. (Leipzig) 134, 177-193]. The solution is derived using the Low Reduced Frequency Approximation method [Tijdeman, (1975). J. Sound Vib. 39, 1-33].

  20. Hydrogen molecule on lithium adsorbed graphene: A DFT study

    International Nuclear Information System (INIS)

    Kaur, Gagandeep; Gupta, Shuchi; Gaganpreet; Dharamvir, Keya

    2016-01-01

    Electronic structure calculations for the adsorption of molecular hydrogen on lithium (Li) decorated and pristine graphene have been studied systematically using SIESTA code [1] within the framework of the first-principle DFT under the Perdew-Burke-Ernzerhof (PBE) form of the generalized gradient approximation (GGA)[2], including spin polarization. The energy of adsorption of hydrogen molecule on graphene is always enhanced by the presence of co-adsorbed lithium. The most efficient adsorption configuration is when H 2 is lying parallel to lithium adsorbed graphene which is in contrast to its adsorption on pristine graphene (PG) where it prefers perpendicular orientation.

  1. Removal of uranium by the adsorbents produced from coffee residues

    International Nuclear Information System (INIS)

    Mahramanlioglu, M.; Bicer, I.O.; Misirli, T.; Kilislioglu, A.

    2007-01-01

    Large amounts of coffee residues contaminate the environment and reprocessing of them as valuable products such as adsorbents will be a good solution from an environmental and economic point of view. In this study some adsorbents were produced from coffee residues and used for batch removal experiments of uranium from aqueous solutions. The adsorption kinetics was found to follow the Lagergren equation. The adsorption process was described with the Langmuir and Freundlich isotherms. Additionally, the effect of different cations on the adsorption of uranium was studied. (author)

  2. Electrochemical Studies of Paraquat Adsorbed onto Crystalline Apatite

    Directory of Open Access Journals (Sweden)

    Moulay Abderrahim EL MHAMMEDI

    2007-09-01

    Full Text Available The carbon paste electrode (CPE has been used to analyze the electrochemical behavior of paraquat (PQ adsorbed onto synthesized hydroxyapatite phosphocalcique (HAP in K2SO4 (0.1M. The cyclic voltammetry results obtained corrobate with square wave voltammetry. The influence of variables such as the concentration of paraquat adsorbed onto apatite (PQ/HAP, and the potential scan rate was tested.X-ray diffraction analysis (XRD, Fourier transformed infrared spectroscopy (FTIR analysis and inductively coupled plasma-atomic emission spectrometry (ICP, AES were used for characterization of the apatite.

  3. Pyridinium molten salts as co-adsorbents in dye-sensitized solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Jui-Cheng; Sun, I-Wen [Department of Chemistry, National Cheng Kung University, Tainan 701 (China); Yang, Cheng-Hsien; Yang, Hao-Hsun; Hsueh, Mao-Lin [Nano-Powder and Thin Film Technology Center, ITRI South, Tainan 709 (China); Ho, Wen-Yueh [Institute of Cosmetic Science, Chia Nan University of Pharmacy and Science, Tainan 717 (China); Chang, Jia-Yaw [Department of Chemical Engineering, National Taiwan University of Science and Technology, Taipei 106 (China)

    2011-01-15

    The influence of using pyridinium molten salts as co-adsorbents to modify the monolayer of a TiO{sub 2} semiconductor on the performance of a dye-sensitized solar cell is studied. The current-voltage characteristics are measured under AM 1.5 (100 mW cm{sup -2}). The pyridinium molten salts significantly enhance the open-circuit photovoltage (V{sub oc}), the short circuit photocurrent density (J{sub sc}) as well as the solar energy conversion efficiency ({eta}). 1-Ethyl-3-carboxypyridinium iodide ([ECP][I]) is applied successfully to prepare an insulating molecular layer with N719, and achieve high energy conversion efficiency as high as 4.49% at 100 mW cm{sup -2} and AM 1.5. The resulting efficiency is 20% higher than that of a non-additive device. This enhancement of conversion efficiency is attributed to the negative shift of the conduction band (CB) edge and the abundant concentration of I{sup -} on the surface of the electrode when using [ECP][I] as the co-adsorbent. (author)

  4. The growth and electronic structure of azobenzene-based functional molecules on layered crystals

    International Nuclear Information System (INIS)

    Iwicki, J; Ludwig, E; Buck, J; Kalläne, M; Kipp, L; Rossnagel, K; Köhler, F; Herges, R

    2012-01-01

    In situ ultraviolet photoelectron spectroscopy is used to study the growth of ultrathin films of azobenzene-based functional molecules (azobenzene, Disperse Orange 3 and a triazatriangulenium platform with an attached functional azo-group) on the layered metal TiTe 2 and on the layered semiconductor HfS 2 at liquid nitrogen temperatures. Effects of intermolecular interactions, of the substrate electronic structure, and of the thermal energy of the sublimated molecules on the growth process and on the adsorbate electronic structure are identified and discussed. A weak adsorbate-substrate interaction is particularly observed for the layered semiconducting substrate, holding the promise of efficient molecular photoswitching.

  5. Development of polymeric adsorbents for recovery of uranium from seawater

    International Nuclear Information System (INIS)

    Britt, P.; Dai, S.; Hay, B.; Janke, C.; Mayes, R.; Saito, T.; Tsouris, C.; Rao, L.

    2014-01-01

    Extraction of uranium from unconventional resources, where uranium is in low concentrations as in seawater, can be orders of magnitude higher in cost than extraction from conventional sources. As a part of the Fuel Cycle Technology Research and Development Program in the United States Department of Energy, Office of Nuclear Energy, Oak Ridge National Laboratory (ORNL) is developing new adsorbents with higher capacities, selectivities, and durability for the cost effective extraction of uranium from seawater, the most challenging but highest-payoff unconventional resource. The ultimate goal is to develop a selective, high capacity, durable adsorbent that can economically extract uranium from seawater. Over the last three years, the key focus of the ORNL R&D efforts has been on increasing the adsorption capacity of amidoxime-based polymeric adsorbents by the radiation-induced graft polymerization on high surface-area polyethylene fiberous trunk materials. These trunk materials have been fabricated through an “islands-in-the-sea” fiber-spinning method, which can considerably enhance the surface area of the high-density polyethylene fibers without compromising its mechanical properties. Acrylonitrile and methacrylic acid can be effectively grafted onto these high surface-area fibers followed by conversion of the nitrile groups to amidoxime groups. Marine testing of these poly(acryamidoxime-co-methacrylic acid) adsorbents at the Pacific Northwest National Laboratory Marine Sciences Laboratory showed uranium adsorption capacities, for the extraction of uranium from seawater, that were more than three-times higher than that previously reported. We are continuing to work to increase the adsorbent capacities of the amidoxime-based adsorbents through optimization of the polymerization conditions and investigation of new grafting methods without the use of ionizing radiation such as Atom-Transfer Radical Polymerization. We have also successfully manufactured several

  6. Atomic force microscopy measurements of topography and friction on dotriacontane films adsorbed on a SiO2 surface

    DEFF Research Database (Denmark)

    Trogisch, S.; Simpson, M.J.; Taub, H.

    2005-01-01

    We report comprehensive atomic force microscopy (AFM) measurements at room temperature of the nanoscale topography and lateral friction on the surface of thin solid films of an intermediate-length normal alkane, dotriacontane (n-C32H66), adsorbed onto a SiO2 surface. Our topographic and frictional...... their location. Above a minimum size, the bulk particles are separated from islands of perpendicularly oriented molecules by regions of exposed parallel layers that most likely extend underneath the particles. We find that the lateral friction is sensitive to the molecular orientation in the underlying...... crystalline film and can be used effectively with topographic measurements to resolve uncertainties in the film structure. We measure the same lateral friction on top of the bulk particles as on the perpendicular layers, a value that is about 2.5 times smaller than on a parallel layer. Scans on top...

  7. Novel Anionic Clay Adsorbents for Boiler-Blow-Down Waters Reclaim and Reuse

    Energy Technology Data Exchange (ETDEWEB)

    Muhammad Sahimi; Theodore Tsotsis

    2010-01-08

    Arsenic (As) and Selenium (Se) are found in water in the form of oxyanions. Relatively high concentrations of As and Se have been reported both in power plant discharges, as well as, in fresh water supplies. The International Agency for Research on Cancer currently classifies As as a group 1 chemical, that is considered to be carcinogenic to humans. In Phase I of this project we studied the adsorption of As and Se by uncalcined and calcined layered double hydroxide (LDH). The focus of the present work is a systematic study of the adsorption of As and Se by conditioned LDH adsorbents. Conditioning the adsorbent significantly reduced the Mg and Al dissolution observed with uncalcined and calcined LDH. The adsorption rates and isotherms have been investigated in batch experiments using particles of four different particle size ranges. As(V) adsorption is shown to follow a Sips-type adsorption isotherm. The As(V) adsorption rate on conditioned LDH increases with decreasing adsorbent particle size; the adsorption capacity, on the other hand, is independent of the particle size. A homogeneous surface diffusion model (HSDM) and a bi-disperse pore model (BPM) - the latter viewing the LDH particles as assemblages of microparticles and taking into account bulk diffusion in the intraparticle pore space, and surface diffusion within the microparticles themselves - were used to fit the experimental kinetic data. The HSDM estimated diffusivity values dependent on the particle size, whereas the BPM predicted an intracrystalline diffusivity, which is fairly invariant with particle size. The removal of As(V) on conditioned LDH adsorbents was also investigated in flow columns, where the impact of important solution and operational parameters such as influent As concentration, pH, sorbent particle size and flow rate were studied. An early breakthrough and saturation was observed at higher flow rates and at higher influent concentrations, whereas a decrease in the sorbent particle

  8. Removal of nickel from wastewater using an agricultural adsorbent

    African Journals Online (AJOL)

    2009-11-26

    Nov 26, 2009 ... qmax is the theoretical maximum adsorption capacity of the adsorbent (mg/g). KL is the Langmuir affinity constant (ℓ/mg). Ce is the supernatant equilibrium concentration of the system (mg/ℓ) (Febrianto et al., 2009). The Freundlich isotherm model can also be expressed in the linearised logarithmic form (Eq.

  9. Removal of nickel from wastewater using an agricultural adsorbent ...

    African Journals Online (AJOL)

    As a result, the highest adsorption capacity was attained at the combined effect of low adsorbent dose, high pH and high initial concentration. On the other hand, the Freundlich isotherm fitted the experimental data better than the Langmuir isotherm. Results of this study indicate that the use of pine sawdust could be a ...

  10. effects of organic matter removal and adsorbate solution ...

    African Journals Online (AJOL)

    Stephen

    (negative adsorption) of one or more chemical species in the region of an interface (Sposito, 1989). The effects of organic matter removal and adsorbate solution composition on phosphate sorption by selected soils of Kwara State were studied. Organic matter was removed by treating the soils with hydrogen peroxide.

  11. Organobentonites as multifunctional adsorbents of organic and inorganic water pollutants

    Directory of Open Access Journals (Sweden)

    Jović-Jovičić Natаša

    2014-01-01

    Full Text Available The aim of this study was to find a low cost, easy to synthesize and efficient adsorbent for the simultaneous adsorption of both organic and inorganic pollutants (including textile dyes, toxic metals etc.. The starting material, domestic bentonite clay from Bogovina was modified with amounts of hexadecyltrimethylammonium cations corresponding to 0.5 and 1.0 times of the value of the cation exchange capacity value. The organobentonites were tested as adsorbents in a three-dye-containing solution, a three-component solution of Pb2+, Cd2+ and Ni2+ and a hexa- component solution containing all investigated dyes and toxic metal cations. The used adsorbents showed the highest affinity toward Acid Yellow 99 and Ni2+ ions. Dye adsorption was enhanced in the presence of toxic metal cations, while the adsorption of all toxic cations from the hexa-component solution was lower than from the three-component solution containing only toxic cations. The synthesized hexadecyltrimethylammonium bentonite could be regarded as an efficient multifunctional adsorbent for the investigated type of water pollutants.

  12. Electrospun chitosan/baker's yeast nanofibre adsorbent: preparation ...

    Indian Academy of Sciences (India)

    The prepared adsorbent was characterized by Brunauer–Emmett–Teller (BET), Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) analyses. The influences of experimental parameters on the chitosan/baker's yeast nanofibre such as contact time, pH, temperature and initial concentration were studied ...

  13. Utilization of Roselle charcoal as nitrate-nitrogen adsorbent

    Directory of Open Access Journals (Sweden)

    Yimrattanabovorn, J.

    2006-11-01

    Full Text Available Recently, the attempts have been made by utilizing natural material as an adsorbent for wastewater treatment due to its low cost, low energy requirement and the fewer chemicals used. In this study, Roselle (Hibiscus sabdariffa L. var. altissima was prepared to use as a charcoal adsorbent in the treatment process. The nitrate-nitrogen adsorption capacities of Roselle charcoal with 2 different particle sizes, A (4.75- .30 mm and B (2.00-4.75 mm were measured and compared with an activated carbon (AC. The equilibrium data fitted well with the Freundlich Isotherm. The K values related to the capacity of adsorbent for nitratenitrogen of such charcoal studied were in the following orders: AC > B > A expressed as 0.0321, 0.0147 and 0.0071 respectively. In addition, activated carbon required less contact time to reach equilibrium than both of Roselle charcoal A and B. Although removal efficiency of activated carbon was higher than that of Roselle charcoal, Roselle charcoal is an interesting alternative adsorbent due to the lower cost of its production.

  14. Waste printing paper as analogous adsorbents for heavy metals in ...

    African Journals Online (AJOL)

    user

    Waste printing paper as analogous adsorbents for heavy metals in aqueous solution. Moyib, O. K.. 1. *, Ayedun. 1. , M. A. ... ABSTRACT. Waste printing paper (WPP) is an abundant local waste material that requires end-use channelling to reduce ..... Science and Technology, 19 2007) 69. 20. Ahalya N., Ramachandra, T. V., ...

  15. Substrate induced ordering of molecular adsorbates on Au(111)

    International Nuclear Information System (INIS)

    Schott, J.H.; White, H.S.; Arana, C.R.

    1992-01-01

    Using scanning tunneling microscopy in dimethylformate, [Ru(bpy) 2 (bpy-(CH 2 ) x -bpy) 2+ ] (x = 4 and 5) monolayers adsorbed on the unreconstructed and √3 x 22 reconstructed surfaces of Au(111) were imaged in this paper. The substrate had a highly ordered pattern on the reconstructed surface, but random spatial distribution on the unreconstructed surface. 17 refs., 3 figs

  16. Analytical phase diagrams for colloids and non-adsorbing polymer

    NARCIS (Netherlands)

    Fleer, G.J.; Tuinier, R.

    2008-01-01

    We review the free-volume theory (FVT) of Lekkerkerker et al. [Europhys. Lett. 20 (1992) 5591 for the phase behavior of colloids in the presence of non-adsorbing polymer and we extend this theory in several aspects: (i) We take the solvent into account as a separate component and show that the

  17. Interactions between adsorbed macromolecules : measurements on emulsions and liquid films

    NARCIS (Netherlands)

    Vliet, van T.

    1977-01-01

    The aim of this study was to gain more insight into the factors, determining the inter- and intramolecular interactions between adsorbed macromolecules. To that end several experimental and theoretical approaches were followed, using well-defined systems. It was shown that these

  18. Application of a high density adsorbent in expanded bed adsorption ...

    African Journals Online (AJOL)

    The application of STREAMLINE Direct HST adsorbent in expanded bed adsorption of lipase from Burkholderia pseudomallei was explored in this study. Scouting of optimum binding and elution condition was performed in batch binding mode. The addition of 0.2 M salt in acetate buffer (pH 5) during adsorption has ...

  19. Efficacy of different adsorbents in reducing the toxic effects of ...

    African Journals Online (AJOL)

    The ability of dietary hydrated sodium calcium aluminosilicate (HSCAS), diatomite and activated charcoal (AC) in reducing the detrimental effects of aflatoxin B1 (AFB1) in broiler diets was evaluated. Adsorbents were supplemented at 2.5 g/kg to the diets containing 0, 40 or 80 μg AFB1/kg feed. One hundred and eighty Ross ...

  20. Kinetics of fibrinopeptides release from fibrinogen adsorbed on a surface

    Czech Academy of Sciences Publication Activity Database

    Riedel, Tomáš; Brynda, Eduard; Houska, Milan; Suttnar, J.; Dyr, J. E.

    2009-01-01

    Roč. 7, Suppl. 1 (2009), PP_TH_213 ISSN 1538-7933. [Congress Boston /22./. 11.07.2009-16.07.2009, Boston] R&D Projects: GA MŠk 1M0538 Institutional research plan: CEZ:AV0Z40500505 Keywords : fibrinopeptides release * adsorbed fibrinogen * thrombin Subject RIV: CD - Macromolecular Chemistry

  1. Development of ultrafiltration and adsorbents: October 1978--March 1979

    International Nuclear Information System (INIS)

    Herald, W.R.; Roberts, R.C.

    1979-01-01

    Studies were conducted to determine the feasibility of using a bone char adsorption column or a reverse osmosis (RO) unit as a treatment secondary to ultrafiltration for Mound aqueous waste. Results showed RO to be much more effective than bone char as a secondary treatment. Tests were performed to determine whether RO would also remove americium-241 from a waste stream. (Plutonium was removed in previous tests.) The results of these tests showed nearly complete removal of americium-241. Data collected from almost 2 yr of operation show that the M-type ultrafiltration membranes are more suitable than D membranes for use in a full-scale system. A literature search is being conducted to find adsorbents for the removal of fission products from waste streams. Adsorbers for cesium have been identified and testing to determine their effectiveness has started. The literature identified by computer search for iodine and cobalt adsorbers is now being studied. Engineering column decontamination factors for americium-241 removal from waste streams with pH of 3, 7, and 10 were determined. A cross reference of adsorbents was compiled in a series of tables so that data from waste treatment reports can be compared

  2. Magnetically modified microbial cells: A new type of magnetic adsorbents

    Czech Academy of Sciences Publication Activity Database

    Šafařík, Ivo; Šafaříková, Miroslava

    2007-01-01

    Roč. 5, 1-2 (2007), s. 19-25 ISSN 1672-2515 R&D Projects: GA MŠk(CZ) OC 108 Institutional research plan: CEZ:AV0Z60870520 Keywords : microbial cells * magnetic modification * magnetic adsorbent Subject RIV: EE - Microbiology, Virology

  3. Application of a high density adsorbent in expanded bed adsorption ...

    African Journals Online (AJOL)

    PRECIOUS

    2010-01-11

    Jan 11, 2010 ... allowed the passage of cells or cell particle with concomitant adsorption of target protein (Jahic et al.,. 2006). Stable expanded bed is critical to the overall pro- cess performance (Jahic et al., 2006), a well performing adsorbent will prevent bed instability and give high breakthrough capacity (Anspach et al., ...

  4. Novel herbal adsorbent based on wheat husk for reactive dye ...

    African Journals Online (AJOL)

    In the present study, wheat husk was applied as a natural adsorbent for the dye C. I. Reactive Yellow 15 removal from aqueous solutions. Different effective parameters of the decolorisation process such as contact time, stirring speed, temperature and pH of solutions were studied and the best condition for achieving the ...

  5. Mercury chemisorption by sulfur adsorbed in porous materials

    NARCIS (Netherlands)

    Steijns, M.; Peppelenbos, A.; Mars, P.

    1976-01-01

    The sorption of mercury vapor by adsorbed sulfur in the zeolites CaA (= 5A) and NaX (=13X) and two types of active carbon has been measured at a temperature of 50°C. With increasing degree of micropore filling by sulfur the fraction of sulfur accessible to mercury atoms decreased for CaA and NaX.

  6. Adsorbed Organic Material and Its Control on Wettability

    DEFF Research Database (Denmark)

    Matthiesen, Jesper; Hassenkam, Tue; Bovet, Nicolas Emile

    2017-01-01

    ethanol/ozone treatment, to be a result of the loss of the organic material that was originally adsorbed on these surfaces, which adds to the charge density and thereby to the salinity dependent EDL force. Investigating the same area on the same pore surface, before and after removal of the organic...

  7. Fast and efficient protein purification using membrane adsorber systems.

    Science.gov (United States)

    Suck, Kirstin; Walter, Johanna; Menzel, Frauke; Tappe, Alexander; Kasper, Cornelia; Naumann, Claudia; Zeidler, Robert; Scheper, Thomas

    2006-02-10

    The purification of proteins from complex cell culture samples is an essential step in proteomic research. Traditional chromatographic methods often require several steps resulting in time consuming and costly procedures. In contrast, protein purification via membrane adsorbers offers the advantage of fast and gentle but still effective isolation. In this work, we present a new method for purification of proteins from crude cell extracts via membrane adsorber based devices. This isolation procedure utilises the membranes favourable pore structure allowing high flow rates without causing high back pressure. Therefore, shear stress to fragile structures is avoided. In addition, mass transfer takes place through convection rather than diffusion, thus allowing very rapid separation processes. Based on this membrane adsorber technology the separation of two model proteins, human serum albumin (HSA) and immungluboline G (IgG) is shown. The isolation of human growth hormone (hGH) from chinese hamster ovary (CHO) cell culture supernatant was performed using a cation exchange membrane. The isolation of the enzyme penicillin acylase from the crude Escherichia coli supernatant was achieved using an anion exchange spin column within one step at a considerable purity. In summary, the membrane adsorber devices have proven to be suitable tools for the purification of proteins from different complex cell culture samples.

  8. Porous polymer adsorbent media constructed by molecular dynamics modeling and simulations: the immobilization of charged ligands and their effect on pore structure and local nonelectroneutrality.

    Science.gov (United States)

    Riccardi, E; Wang, J-C; Liapis, A I

    2009-02-26

    A molecular dynamics modeling and simulation approach is presented and employed to construct porous dextran polymer ion-exchange adsorbent media. Both the activation step of the surface of the pores of the dextran polymer layer grafted on an agarose surface and the immobilization of charged ligands on the activated surface of the porous dextran polymer layer are considered. For the systems studied in this work, the activation step modifies slightly the pore structure of the base, nonactivated porous dextran polymer, while the immobilization of the ligands on the activated pore surface of the dextran layer changes significantly the pore structure of the activated dextran layer. The density distributions of the counterions and immobilized charged ligands along the direction of net transport in the adsorbent media constructed in this study are found to be nonuniform. The variables that affect the shape and magnitude of the density distributions of the counterions and immobilized charged ligands as well as the total number of charged ligands that can be immobilized on the activated porous dextran layer are identified and presented in this work. Furthermore, the data clearly show that there is local nonelectroneutrality in the porous dextran polymer ion-exchange adsorbent media, and this result has very important practical implications for the operation and performance of separation systems involving ion-exchange adsorbent media (e.g., ion-exchange chromatography systems). Also, the results of this work suggest approaches for (1) controlling the immobilization process of charged ligands and (2) constructing and studying the behavior of chromatographic polymeric monoliths and packed bed columns having a gradient of density of functionalities along the axis of the chromatographic polymeric monolith or packed bed column.

  9. Metal-phthalocyanine ordered layers on Au(110): Metal-dependent adsorption energy

    Energy Technology Data Exchange (ETDEWEB)

    Massimi, Lorenzo, E-mail: lorenzo.massimi@uniroma1.it; Angelucci, Marco; Gargiani, Pierluigi; Betti, Maria Grazia [Dipartimento di Fisica, Università di Roma La “Sapienza,” 00185 Roma (Italy); Montoro, Silvia [IFIS Litoral, CONICET-UNL, Laboratorio de Fisica de Superficies e Interfaces, Güemes 3450, Santa Fe (Argentina); Mariani, Carlo, E-mail: carlo.mariani@uniroma1.it [Dipartimento di Fisica, CNISM, Università di Roma La “Sapienza,” 00185 Roma (Italy)

    2014-06-28

    Iron-phthalocyanine and cobalt-phthalocyanine chains, assembled along the Au(110)-(1×2) reconstructed channels, present a strong interaction with the Au metallic states, via the central metal ion. X-ray photoemission spectroscopy from the metal-2p core-levels and valence band high-resolution ultraviolet photoelectron spectroscopy bring to light signatures of the interaction of the metal-phthalocyanine single-layer with gold. The charge transfer from Au to the molecule causes the emerging of a metal-2p core level component at lower binding energy with respect to that measured in the molecular thin films, while the core-levels associated to the organic macrocycle (C and N 1s) are less influenced by the adsorption, and the macrocycles stabilize the interaction, inducing a strong interface dipole. Temperature Programmed Desorption experiments and photoemission as a function of temperature allow to estimate the adsorption energy for the thin-films, mainly due to the molecule-molecule van der Waals interaction, while the FePc and CoPc single-layers remain adsorbed on the Au surface up to at least 820 K.

  10. Removal of microcystin-LR from drinking water using a bamboo-based charcoal adsorbent modified with chitosan.

    Science.gov (United States)

    Zhang, Hangjun; Zhu, Guoying; Jia, Xiuying; Ding, Ying; Zhang, Mi; Gao, Qing; Hu, Ciming; Xu, Shuying

    2011-01-01

    A new kind of low-cost syntactic adsorbent from bamboo charcoal and chitosan was developed for the removal of microcystin-LR from drinking water. Removal efficiency was higher for the syntactic adsorbent when the amount of bamboo charcoal was increased. The optimum dose ratio of bamboo charcoal to chitosan was 6:4, and the optimum amount was 15 mg/L; equilibrium time was 6 hr. The adsorption isotherm was non-linear and could be simulated by the Freundlich model (R2 = 0.9337). Adsorption efficiency was strongly affected by pH and natural organic matter (NOM). Removal efficiency was 16% higher at pH 3 than at pH 9. Efficiency rate was reduced by 15% with 25 mg/L NOM (UV254 = 0.089 cm(-1)) in drinking water. This study demonstrated that the bamboo charcoal modified with chitosan can effectively remove microcystin-LR from drinking water.

  11. Kinetics of the Removal of Chromium Complex Dye from Aqueous Solutions Using Activated Carbons and Polymeric Adsorbent

    Directory of Open Access Journals (Sweden)

    Eglė Kazlauskienė

    2011-04-01

    Full Text Available The kinetics of the removal of chromium complex dye (Lanasyn Navy M-DNL from aqueous solutions using polymeric adsorbent Macronet MN 200 (MN 200 as an alternative option for activated carbon Norit RB 0.8 CC (AC was studied in the batch system. The residual colour of dye solution treated with AC or MN 200 strongly depends on solution pH with lower values at acidic pH when a positively charged surface net is favourable for the adsorption of the dye anion. The removal of dye using MN 200 was found relatively higher than that using AC. The pseudo-second order and intraparticle diffusion models agreed well with experimental data. The parameters of these models were studied as a function of temperature and adsorbent nature.Article in Lithuanian

  12. Surface-enhanced raman spectroscopy of quinomethionate adsorbed on silver colloids

    International Nuclear Information System (INIS)

    Kim, Mak Soon; Kang, Jae Soo; Park, Si Bum; Lee, Mu Sang

    2003-01-01

    We have studied the surface-enhanced Raman spectroscopy (SERS) spectrum of quinomethionate (6-methyl-1,3-dithiolo(4,5-b)quinoxalin-2-one), which is an insecticide or fungicide used on vegetables and wheat. We observed no signals in the ordinary Raman spectra of solid-state quinomethionate, but when it was adsorbed on a colloidal silver surface, strong vibrational signals were obtained at a very low concentration. The SERS spectra were obtained by silver colloids prepared by the Creighton et al. method. The influence of pH and the aggregation inductors (Cl - , Br - , I - , F - ) on the adsorption mechanism was investigated. Two different adsorption mechanisms were deduced, depending on the experimental conditions: The one N atom or two N atoms are chemisorbed on an Ag surface. An important contribution of the chemical mechanism was inferred when the one N atom was perpendicularly adsorbed on a surface. It is possible that quinomethionate can be detected to about 10 -5 M

  13. Adsorbing H₂S onto a single graphene sheet: A possible gas sensor

    Energy Technology Data Exchange (ETDEWEB)

    Reshak, A. H., E-mail: maalidph@yahoo.co.uk [New Technologies-Research Centre, University of West Bohemia, Univerzitni 8, 306 14 Pilsen (Czech Republic); Center of Excellence Geopolymer and Green Technology, School of Material Engineering, University Malaysia Perlis, 01007 Kangar, Perlis (Malaysia); Auluck, S. [Council of Scientific and Industrial Research-National Physical Laboratory, Dr. K S Krishnan Marg, New Delhi 110012 (India)

    2014-09-14

    The electronic structure of pristine graphene sheet and the resulting structure of adsorbing a single molecule of H₂S on pristine graphene in three different sites (bridge, top, and hollow) are studied using the full potential linearized augmented plane wave method. Our calculations show that the adsorption of H₂S molecule on the bridge site opens up a small direct energy gap of about 0.1 eV at symmetry point M, while adsorption of H₂S on top site opens a gap of 0.3 eV around the symmetry point K. We find that adsorbed H₂S onto the hollow site of pristine graphene sheet causes to push the conduction band minimum and the valence band maximum towards Fermi level resulting in a metallic behavior. Comparing the angular momentum decomposition of the atoms projected electronic density of states of pristine graphene sheet with that of H₂S–graphene for three different cases, we find a significant influence of the location of the H₂S molecule on the electronic properties especially the strong hybridization between H₂S molecule and graphene sheet.

  14. Adsorption of Mefenamic Acid From Water by Bentonite Poly urea formaldehyde Composite Adsorbent

    Directory of Open Access Journals (Sweden)

    Basma Abbas Abdel Majeed

    2017-07-01

    Full Text Available Poly urea formaldehyde –Bentonite (PUF-Bentonite composite was tested as new adsorbent for removal of mefenamic acid (MA from simulated wastewater in batch adsorption procedure. Developed a method for preparing poly urea formaldehyde gel in basic media by using condensation polymerization. Adsorption experiments were carried out as a function of water pH, temperature, contact time, adsorbent dose and initial MA concentration .Effect of sharing surface with other analgesic pharmaceuticals at different pH also studied. The adsorption of MA was found to be strongly dependent to pH. The Freundlich isotherm model showed a good fit to the equilibrium adsorption data. From Dubinin–Radushkevich model the mean free energy (E was calculated and the value of 5 KJ/mole indicated that the main mechanism governing the adsorption of MA on PUF-Bentonite composite was physical in nature. The kinetics of adsorption tested for first order, pseudo second order models and Elovich’s equation, results showed the adsorption followed the pseudo-second-order model

  15. Preparation of Fly ash Based Adsorbents for Removal Active Red X-3B from Dying Wastewater

    Directory of Open Access Journals (Sweden)

    Li Jinping

    2016-01-01

    Full Text Available Fly ash with a large number of active sites can occur with the adsorbent chemical and physical adsorption, and therefore have a strong adsorption capacity. The original fly ash and raw fly ash compared to the physical and chemical properties to a significant change. On the fly ash in industrial water treatment application were outlined. The purpose is to focus on the modification methods of fly ash and comparison of raw fly ash and fly ash in the effect of dyeing wastewater. Single factor test method; select the appropriate modifier to study the dosage, pH, stirring time on the modification of adsorption properties of fly ash before and after. The results showed that the modified fly ash was better than the adsorption. Greatly improves on active red X-3B dye wastewater removal capacity, pH = 5, 6, dosage is 5g / L, the mixing time is 30min, COD removal rate reached 73.07%. This modified material can be used as adsorbent for pre-treating dying wastewater.

  16. Inversion of type of separation system in planar chromatography of peptides, using C18 silica-based adsorbents.

    Science.gov (United States)

    Gwarda, Radosław Ł; Aletańska-Kozak, Monika; Matosiuk, Dariusz; Dzido, Tadeusz H

    2016-04-01

    Our previous results show, that C18 silica-based adsorbents used in high-performance thin-layer chromatography (HPTLC), provide complex retention mechanism basing on various polar and nonpolar interactions. Here we present, that in chromatography of peptides, due to mixed-mode properties of these adsorbents, there is a simple way to obtain inversion of separation system type (from reversed-phase, RP, to normal-phase, NP, and vice versa). The results presented provide detailed information how to obtain inversion mentioned and reflect the extent (the type and concentration of organic solvent, the type and concentration of ion-pairing reagent in the mobile phase) of this phenomenon. We show, that the system type inversion results in significant change of selectivity of separation, which may be especially useful in 2D separation of complex samples of basic/amphoteric compounds such as peptides. This results from the fact, that C18 silica-based HPTLC adsorbents, may be used in hydrophilic interaction chromatography (HILIC) or RP chromatography, in dependence on mobile phase composition. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Spectroscopic Studies of Abiotic and Biological Nanomaterials: Silver Nanoparticles, Rhodamine 6G Adsorbed on Graphene, and c-Type Cytochromes and Type IV Pili in Geobacter sulfurreducens

    Science.gov (United States)

    Thrall, Elizabeth S.

    This thesis describes spectroscopic studies of three different systems: silver nanoparticles, the dye molecule rhodamine 6G adsorbed on graphene, and the type IV pili and c-type cytochromes produced by the dissimilatory metal-reducing bacterium Geobacter sulfurreducens. Although these systems are quite different in some ways, they can all be considered examples of nanomaterials. A nanomaterial is generally defined as having at least one dimension below 100 nm in size. Silver nanoparticles, with sub-100 nm size in all dimensions, are examples of zero-dimensional nanomaterials. Graphene, a single atomic layer of carbon atoms, is the paradigmatic two-dimensional nanomaterial. And although bacterial cells are on the order of 1 μm in size, the type IV pili and multiheme c-type cytochromes produced by G. sulfurreducens can be considered to be one- and zero-dimensional nanomaterials respectively. A further connection between these systems is their strong interaction with visible light, allowing us to study them using similar spectroscopic tools. The first chapter of this thesis describes research on the plasmon-mediated photochemistry of silver nanoparticles. Silver nanoparticles support coherent electron oscillations, known as localized surface plasmons, at resonance frequencies that depend on the particle size and shape and the local dielectric environment. Nanoparticle absorption and scattering cross-sections are maximized at surface plasmon resonance frequencies, and the electromagnetic field is amplified near the particle surface. Plasmonic effects can enhance the photochemistry of silver particles alone or in conjunction with semiconductors according to several mechanisms. We study the photooxidation of citrate by silver nanoparticles in a photoelectrochemical cell, focusing on the wavelength-dependence of the reaction rate and the role of the semiconductor substrate. We find that the citrate photooxidation rate does not track the plasmon resonance of the silver

  18. Interstitial and adsorbed phosphates in shelf sediments off Visakhapatnam, east coast of India

    Digital Repository Service at National Institute of Oceanography (India)

    Sarma, V.V.; Raju, G.R.K.

    Spatial distribution of interstitial and adsorbed phosphates in the shelf sediments shows an increasing trend with distance from coastal to inshore region. Maximum concentration ranges of interstitial and adsorbed phosphates are 16-19 and 40-50 mu g...

  19. Novel adsorbent applicability for decontamination of printing wastewater

    Science.gov (United States)

    Kiurski, Jelena; Oros, Ivana; Ranogajec, Jonjaua; Kecic, Vesna

    2013-04-01

    Adsorption capacity of clayey minerals can be enhanced by replacing the natural exchangeable cations with organic cations, which makes the clay surface more hydrophobic. Different solids such as activated carbon, clay minerals, zeolites, metal oxides and organic polymers have been tested as effective adsorbents. On a global scale, clays have a large applicability for decontamination, purification of urban and industrial residual waters, protection of waste disposal areas, and purification of industrial gases and so on. Clay derivative materials with high adsorption capacities are very attractive from an economical point of view. Due to the economic constraints, a development of cost effective and clean processes is desired. Adsorption processes has proved to be the most effective, especially for effluents with moderate and low heavy metal concentrations, as like as in printing wastewaters. Among several removal technologies, the adsorption of Zn(II) ion onto NZ, B, pure C and C with PEG 600 addition could be of great importance for the printing wastewaters purification. However, the newly designed adsorbent of the defined pore size distribution and phase structure considered as the most suitable material for Zn(II) ion removal. The values of distribution coefficient (Kd) increased with decreasing of the adsorbent amount. The Kd values depend also on the type of used adsorbent, the following increased order is obtained: NZ Langmuir > DKR. The study also showed that the fired clay modified with PEG 600 addition has great potential (up to 93.5%) to remove Zn(II) ion from printing wastewaters. The results showed that fired clay, fired clay modified with polymer addition, natural zeolite and bentonite can be used for Zn(II) ion removal from printing wastewaters by adsorption method in laboratory batch mode. Based on higher affinity to the Zn(II) ion adsorption than fired clay, bentonite and zeolite it was concluded that feasibility of newly designed clayey adsorbent

  20. Adsorbed carbon nanomaterials for surface and interface-engineered stable rubidium multi-cation perovskite solar cells.

    Science.gov (United States)

    Mahmud, Md Arafat; Elumalai, Naveen Kumar; Upama, Mushfika Baishakhi; Wang, Dian; Zarei, Leila; Gonçales, Vinicius R; Wright, Matthew; Xu, Cheng; Haque, Faiazul; Uddin, Ashraf

    2018-01-03

    The current work reports the simultaneous enhancement in efficiency and stability of low-temperature, solution-processed triple cation based MA 0.57 FA 0.38 Rb 0.05 PbI 3 (MA: methyl ammonium, FA: formamidinium, Rb: rubidium) perovskite solar cells (PSCs) by means of adsorbed carbon nanomaterials at the perovskite/electron transporting layer interface. The quantity and quality of the adsorbents are precisely controlled to electronically modify the ETL surface and lower the energy barrier across the interface. Carbon derivatives namely fullerene (C 60 ) and PC 71 BM ([6,6]-phenyl C71 butyric acid methyl ester) are employed as adsorbents in conjunction with ZnO and together serve as a bilayer electron transporting layer (ETL). The adsorbed fullerene (C 60 -ZnO, abbreviated as C-ZnO) passivates the interstitial trap-sites of ZnO with interstitial intercalation of oxygen atoms in the ZnO lattice structure. C-ZnO ETL based PSCs demonstrate about a 19% higher average PCE compared to conventional ZnO ETL based devices and a nearly 9% higher average PCE than PC 71 BM adsorbed-ZnO (P-ZnO) ETL based PSCs. In addition, the interstitial trap-state passivation with a C-ZnO film upshifts the Fermi-level position of the C-ZnO ETL by 130 meV, with reference to the ZnO ETL, which contributes to an enhanced n-type conductivity. The photocurrent hysteresis phenomenon in C-ZnO PSCs is also substantially reduced due to mitigated charge trapping phenomena and concomitant reduction in an electrode polarization process. Another major highlight of this work is that, C-ZnO PSCs demonstrate a superior device stability retaining about 94% of its initial PCE in the course of a month-long, systematic degradation study conducted in our work. The enhanced device stability with C-ZnO PSCs is attributed to their high resistance to aging-induced recombination phenomena and a water-induced perovskite degradation process, due to a lower content of oxygen-related chemisorbed species on the C-ZnO ETL

  1. Competitive Adsorption of a Two-Component Gas on a Deformable Adsorbent

    OpenAIRE

    Usenko, A. S.

    2013-01-01

    We investigate the competitive adsorption of a two-component gas on the surface of an adsorbent whose adsorption properties vary in adsorption due to the adsorbent deformation. The essential difference of adsorption isotherms for a deformable adsorbent both from the classical Langmuir adsorption isotherms of a two-component gas and from the adsorption isotherms of a one-component gas taking into account variations in adsorption properties of the adsorbent in adsorption is obtained. We establi...

  2. Strong Josephson Coupling in Planar Graphene Junctions

    Science.gov (United States)

    Park, Jinho; Lee, Gil-Ho; Lee, Jae Hyeong; Takane, Yositake; Imura, Ken-Ichiro; Taniguchi, Takashi; Watanabe, Kenji; Lee, Hu-Jong

    A recent breakthrough of processing graphene, employing encapsulation by hexagonal boron nitride layers (BGB structure), allows realizing the ballistic carrier transport in graphene. Thereafter, ballistic Josephson coupling has been studied by closely edge-contacted BGB structure with two superconducting electrodes. Here, we report on the strong Josephson coupling with planar graphene junction in truly short and ballistic regime. Our device showed high transmission probability and the junction critical current (IC) oscillating for sweeping the gate voltage along with the normal conductance oscillation (Fabry-Perot oscillations), providing a direct evidence for the ballistic nature of the junction pair current. We also observed the convex-upward shape of decreasing critical currents with increasing temperature, canonical properties of the short Josephson coupling. By fitting these curves into theoretical models, we demonstrate the strong Josephson coupling in our devices, which is also supported by the exceptionally large value of ICRN ( 2 Δ / e RNis the normal resistance).

  3. Wall Layers

    Science.gov (United States)

    1992-01-14

    Mathematical Sciences Institute. Ithaca, NY: Cornell. Guckenheimer, J. & Labouriau, 1. 1990. Bifurcation of the Hodgkin - Huxley equations: a new vt.vist. In...olm es -____ II_ John Guckenheimer Avwi tI.,,ti 1it y ’odes ,Av9L! an.,I/or Dist Special •D L 2 Narrative Philip Holmes is continuing to study the...not localized in spae like the structur observed in the turbulent baft y layer. Wavelet bases, having compact support, seem much more appropriate. J

  4. Single-unit-cell layer established Bi 2 WO 6 3D hierarchical architectures: Efficient adsorption, photocatalysis and dye-sensitized photoelectrochemical performance

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Hongwei; Cao, Ranran; Yu, Shixin; Xu, Kang; Hao, Weichang; Wang, Yonggang; Dong, Fan; Zhang, Tierui; Zhang, Yihe

    2017-12-01

    Single-layer catalysis sparks huge interests and gains widespread attention owing to its high activity. Simultaneously, three-dimensional (3D) hierarchical structure can afford large surface area and abundant reactive sites, contributing to high efficiency. Herein, we report an absorbing single-unit-cell layer established Bi2WO6 3D hierarchical architecture fabricated by a sodium dodecyl benzene sulfonate (SDBS)-assisted assembled strategy. The DBS- long chains can adsorb on the (Bi2O2)2+ layers and hence impede stacking of the layers, resulting in the single-unit-cell layer. We also uncovered that SDS with a shorter chain is less effective than SDBS. Due to the sufficient exposure of surface O atoms, single-unit-cell layer 3D Bi2WO6 shows strong selectivity for adsorption on multiform organic dyes with different charges. Remarkably, the single-unit-cell layer 3D Bi2WO6 casts profoundly enhanced photodegradation activity and especially a superior photocatalytic H2 evolution rate, which is 14-fold increase in contrast to the bulk Bi2WO6. Systematic photoelectrochemical characterizations disclose that the substantially elevated carrier density and charge separation efficiency take responsibility for the strengthened photocatalytic performance. Additionally, the possibility of single-unit-cell layer 3D Bi2WO6 as dye-sensitized solar cells (DSSC) has also been attempted and it was manifested to be a promising dye-sensitized photoanode for oxygen evolution reaction (ORR). Our work not only furnish an insight into designing single-layer assembled 3D hierarchical architecture, but also offer a multi-functional material for environmental and energy applications.

  5. Guiding principles for the development and application of solid-phase phosphorus adsorbents for freshwater ecosystems

    NARCIS (Netherlands)

    Douglas, G.B.; Hamilton, D.P.; Robb, M.S.; Pan, G.; Spears, B.M.; Lurling, M.

    2016-01-01

    Whilst a diverse array of phosphorus (P)-adsorbent materials is currently available for application to freshwater aquatic systems, selection of the most appropriate P-adsorbents remains problematic. In particular, there has to be a close correspondence between attributes of the P-adsorbent, its

  6. Single stage batch adsorber design for efficient Eosin yellow removalby polyaniline coated ligno-cellulose

    CSIR Research Space (South Africa)

    Debnath, S

    2015-01-01

    Full Text Available Polyaniline-coated lignin-based adsorbent (PLC) was synthesized and used for uptake of reactive dye eosin yellow (EY) from aqueous solution. The adsorption capability of the adsorbent was found to be more effective than the unmodified adsorbent (LC...

  7. Palladium dimers adsorbed on graphene: A DFT study

    International Nuclear Information System (INIS)

    Kaur, Gagandeep; Gupta, Shuchi; Dharamvir, Keya

    2015-01-01

    The 2D structure of graphene shows a great promise for enhanced catalytic activity when adsorbed with palladium. We performed a systematic density functional theory (DFT) study of the adsorption of palladium dimer (Pd 2 ) on graphene using SIESTA package, in the generalized gradient approximation (GGA). The adsorption energy, geometry, and charge transfer of Pd 2 -graphene system are calculated. Both horizontal and vertical orientations of Pd 2 on graphene are studied. Our calculations revealed that the minimum energy configuration for Pd dimer is parallel to the graphene sheet with its two atoms occupying centre of adjacent hexagonal rings of graphene sheet. Magnetic moment is induced for Pd dimer adsorbed on graphene in vertical orientation while horizontal orientation of Pd dimer on graphene do not exhibit magnetism. Insignificant energy differences among adsorption sites means that dimer mobility on the graphene sheet is high. There is imperceptible distortion of graphene sheet perpendicular to its plane. However, some lateral displacements are seen

  8. Biologically Degradable Adsorbents in Treatment of Coloured Wastewater

    Directory of Open Access Journals (Sweden)

    Maja Klančnik

    2018-03-01

    Full Text Available In this research, the adsorption capacity of biodegradable wastes such as peels of lemon, orange, mandarin, avocado, apples, banana and over-matured banana in the treatment of coloured wastewaters polluted with direct dye and with pigment screen printing ink was studied. Their adsorption capacity was compared with already established adsorbents such as activated carbon, zeolite, alumina and chitosan. The efficiency of the adsorption treatment was evaluated by a spectrophotometric measurement of colour removal of the wastewater. In both coloured wastewaters, dried banana and dried ground lemon peel proved to be excellent biodegradable adsorbents, which were even more effective than commercially used activated carbon. The dried ground orange, mandarin and apple peels also showed adsorption abilities in the coloured wastewaters. In the water contaminated with dye, the equally high level of discoloration obtained with lemon peel and dried banana was also reached with chitosan and alumina.

  9. Inelastic Neutron Scattering from Hydrogen Adsorbed in Carbon

    Science.gov (United States)

    Olsen, Raina; Beckner, Matthew; Taub, Haskell; Pfeifer, Peter; Wexler, Carlos

    2011-03-01

    Inelastic neutron scattering (INS) from adsorbed hydrogen offers a powerful tool to probe the local adsorption environment of storage material. We will show recently measured INS spectra of hydrogen adsorbed on four different carbon samples and discuss the interpretation of their spectral features, using previous theoretical calculations. Both rotational and vibrational transitions can be observed, along with free recoil scattering parallel to the adsorption plane. The spectra from carbon nanotubes and activated carbon are well explained by theory. However, the spectra from PVDC carbon is quite unusual. This material is based upon work supported in part by the Department of Energy under Award Nos. DE-FG02-07ER46411, DE-FG36-08GO18142, and DE-AC02-06CH11357.

  10. pyIAST: Ideal adsorbed solution theory (IAST) Python package

    Science.gov (United States)

    Simon, Cory M.; Smit, Berend; Haranczyk, Maciej

    2016-03-01

    Ideal adsorbed solution theory (IAST) is a widely-used thermodynamic framework to readily predict mixed-gas adsorption isotherms from a set of pure-component adsorption isotherms. We present an open-source, user-friendly Python package, pyIAST, to perform IAST calculations for an arbitrary number of components. pyIAST supports several common analytical models to characterize the pure-component isotherms from experimental or simulated data. Alternatively, pyIAST can use numerical quadrature to compute the spreading pressure for IAST calculations by interpolating the pure-component isotherm data. pyIAST can also perform reverse IAST calculations, where one seeks the required gas phase composition to yield a desired adsorbed phase composition.

  11. Plant waste materials from restaurants as the adsorbents for dyes

    Directory of Open Access Journals (Sweden)

    Pavlović Marija D.

    2015-01-01

    Full Text Available This paper has demonstrated the valorization of inexpensive and readily available restaurant waste containing most consumed food and beverage residues as adsorbents for methylene blue dye. Coffee, tea, lettuce and citrus waste have been utilized without any pre-treatment, thus the adsorption capacities and dye removal efficiency were determined. Coffee waste showed highest adsorbent capacity, followed by tea, lettuce and citrus waste. The dye removal was more effective as dye concentration increases from 5 up to 60 mg/L. The favorable results obtained for lettuce waste have been especially encouraged, as this material has not been commonly employed for sorption purposes. Equilibrium data fitted very well in a Freundlich isotherm model, whereas pseudo-second-order kinetic model describes the process behavior. Restaurant waste performed rapid dye removal at no cost, so it can be adopted and widely used in industries for contaminated water treatment.

  12. Determination of Cr and Cd concentration adsorbed by chicken feathers

    International Nuclear Information System (INIS)

    Lopez M, A.; Cuapio O, L.A.; Cardenas P, S.; Balcazar, M.; Jauregui, V.; Bonilla P, A.

    2008-01-01

    In this work the results of the samples analysis of chicken feathers are presented, used as adsorber of the heavy metals Cd and Cr present in water solutions with well-known concentrations of these metals. It was used the Neutron Activation Analysis technique (AAN), using the TRIGA Mark-III reactor of the Nuclear Center of Mexico. The obtained results they show the advantages of having a versatile installation for the analysis of this type of samples. By means of the analysis of the results, it was determined the feasibility of using chicken feathers like adsorber of these metals present in polluted waters, additionally, it was detected the presence of others polluting elements in the inputs to prepare the reference solutions as well as in the processes, so much of preparation of the feathers like of the metals adsorption. (Author)

  13. Electron bombardment of water adsorbed on Zr(0001) surfaces

    CERN Document Server

    Ankrah, S; Ramsier, R D

    2003-01-01

    A study of the effects of electron bombardment on water adsorbed on Zr(0001) is reported. Zirconium surfaces are dosed with isotopic water mixtures at 160 K followed by electron bombardment (485 eV). The system is then probed by low energy electron diffraction, temperature programmed desorption (TPD) and Auger electron spectroscopy (AES). No evidence is found that would indicate preferential mixing of hydrogen from the bulk with isotopic water dissociation products during TPD. However, electron bombardment results in the sharpening of a hydrogen/deuterium desorption peak near 320 K and the production of water near 730 K at low water exposures. In addition, although water does not oxidize Zr(0001) thermally, electron bombardment of adsorbed water induces a shift of about 2 eV in the Zr AES features indicating that the surface is partially oxidized by electron bombardment.

  14. Adsorbate-driven cooling of carbene-based molecular junctions

    Czech Academy of Sciences Publication Activity Database

    Foti, Giuseppe; Vázquez, Héctor

    2017-01-01

    Roč. 8, Oct (2017), s. 2060-2068 ISSN 2190-4286 R&D Projects: GA ČR GA15-19672S EU Projects: European Commission(XE) 702114 - HEATEXMOL Institutional support: RVO:68378271 Keywords : adsorbate * carbene * current-induced heating and cooling * molecular junction * vibrations Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 3.127, year: 2016

  15. Toxicity of Uranium Adsorbent Materials using the Microtox Toxicity Test

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jiyeon [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jeters, Robert T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gill, Gary A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kuo, Li-Jung [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Bonheyo, George T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-10-01

    The Marine Sciences Laboratory at the Pacific Northwest National Laboratory evaluated the toxicity of a diverse range of natural and synthetic materials used to extract uranium from seawater. The uranium adsorbent materials are being developed as part of the U. S. Department of Energy, Office of Nuclear Energy, Fuel Resources Program. The goal of this effort was to identify whether deployment of a farm of these materials into the marine environment would have any toxic effects on marine organisms.

  16. Application of ESR to the study of adsorbed species

    International Nuclear Information System (INIS)

    Naccache, C.

    1975-01-01

    Electron spin resonance (ESR) enables the defects and paramagnetic species present at the surface of solids to be studied. The informations obtained from these studies lead to a better knowledge of the activation process of certain adsorbed molecules. A brief review is given of ESR principles. Some experimental results are described concerning the adsorption of monoatomic ions and atoms, the inorganic radicals, the reactivity of the O - and O 2 - ions and the adsorption of transition ions [fr

  17. Non-linear optical studies of adsorbates: Spectroscopy and dynamics

    International Nuclear Information System (INIS)

    Zhu, Xiangdong.

    1989-08-01

    In the first part of this thesis, we have established a systematic procedure to apply the surface optical second-harmonic generation (SHG) technique to study surface dynamics of adsorbates. In particular, we have developed a novel technique for studies of molecular surface diffusions. In this technique, the laser-induced desorption with two interfering laser beams is used to produce a monolayer grating of adsorbates. The monolayer grating is detected with diffractions of optical SHG. By monitoring the first-order second-harmonic diffraction, we can follow the time evolution of the grating modulation from which we are able to deduce the diffusion constant of the adsorbates on the surface. We have successfully applied this technique to investigate the surface diffusion of CO on Ni(111). The unique advantages of this novel technique will enable us to readily study anisotropy of a surface diffusion with variable grating orientation, and to investigate diffusion processes of a large dynamic range with variable grating spacings. In the second part of this work, we demonstrate that optical infrared-visible sum-frequency generation (SFG) from surfaces can be used as a viable surface vibrational spectroscopic technique. We have successfully recorded the first vibrational spectrum of a monolayer of adsorbates using optical infrared-visible SFG. The qualitative and quantitative correlation of optical SFG with infrared absorption and Raman scattering spectroscopies are examined and experimentally demonstrated. We have further investigated the possibility to use transient infrared-visible SFG to probe vibrational transients and ultrafast relaxations on surfaces. 146 refs

  18. CHEMICAL REACTIONS ON ADSORBING SURFACE: KINETIC LEVEL OF DESCRIPTION

    Directory of Open Access Journals (Sweden)

    P.P.Kostrobii

    2003-01-01

    Full Text Available Based on the effective Hubbard model we suggest a statistical description of reaction-diffusion processes for bimolecular chemical reactions of gas particles adsorbed on the metallic surface. The system of transport equations for description of particles diffusion as well as reactions is obtained. We carry out the analysis of the contributions of all physical processes to the formation of diffusion coefficients and chemical reactions constants.

  19. Linear response theory of activated surface diffusion with interacting adsorbates

    Energy Technology Data Exchange (ETDEWEB)

    Marti' nez-Casado, R. [Department of Chemistry, Imperial College London, South Kensington, London SW7 2AZ (United Kingdom); Sanz, A.S.; Vega, J.L. [Instituto de Fi' sica Fundamental, Consejo Superior de Investigaciones Cientificas, Serrano 123, 28006 Madrid (Spain); Rojas-Lorenzo, G. [Instituto Superior de Tecnologi' as y Ciencias Aplicadas, Ave. Salvador Allende, esq. Luaces, 10400 La Habana (Cuba); Instituto de Fi' sica Fundamental, Consejo Superior de Investigaciones Cienti' ficas, Serrano 123, 28006 Madrid (Spain); Miret-Artes, S., E-mail: s.miret@imaff.cfmac.csic.es [Instituto de Fi' sica Fundamental, Consejo Superior de Investigaciones Cienti' ficas, Serrano 123, 28006 Madrid (Spain)

    2010-05-12

    Graphical abstract: Activated surface diffusion with interacting adsorbates is analyzed within the Linear Response Theory framework. The so-called interacting single adsorbate model is justified by means of a two-bath model, where one harmonic bath takes into account the interaction with the surface phonons, while the other one describes the surface coverage, this leading to defining a collisional friction. Here, the corresponding theory is applied to simple systems, such as diffusion on flat surfaces and the frustrated translational motion in a harmonic potential. Classical and quantum closed formulas are obtained. Furthermore, a more realistic problem, such as atomic Na diffusion on the corrugated Cu(0 0 1) surface, is presented and discussed within the classical context as well as within the framework of Kramer's theory. Quantum corrections to the classical results are also analyzed and discussed. - Abstract: Activated surface diffusion with interacting adsorbates is analyzed within the Linear Response Theory framework. The so-called interacting single adsorbate model is justified by means of a two-bath model, where one harmonic bath takes into account the interaction with the surface phonons, while the other one describes the surface coverage, this leading to defining a collisional friction. Here, the corresponding theory is applied to simple systems, such as diffusion on flat surfaces and the frustrated translational motion in a harmonic potential. Classical and quantum closed formulas are obtained. Furthermore, a more realistic problem, such as atomic Na diffusion on the corrugated Cu(0 0 1) surface, is presented and discussed within the classical context as well as within the framework of Kramer's theory. Quantum corrections to the classical results are also analyzed and discussed.

  20. Removal of arsenic from drinking water by natural adsorbents

    OpenAIRE

    MD SHAHNOOR ALAM KHAN

    2017-01-01

    The presence of arsenic in groundwater has been reported in many countries across the world and it is a serious threat to public health. The aim of this study was to identify prospective natural materials with high arsenic adsorption capacity and durable hydraulic property to produce adequate flow of water. The comparative study identified Skye sand as the best natural adsorbent. The prototype household filter with Skye sand achieved complete removal of arsenic and iron. Arsenic removal by du...

  1. Adsorbate Reorganization at Steps: NO on Pd(211)

    DEFF Research Database (Denmark)

    Hammer, Bjørk; Nørskov, Jens Kehlet

    1997-01-01

    The interaction of nitric oxide, NO, with the stepped Pd(211) surface is studied using density functional theory slab calculations. Calculated chemisorption energies and geometries reveal that surface sites are not populated in a sequential manner as the NO coverage is increased. This comes about...... through mutual NO interactions that reorganize the adsorbates during the adsorption. The finding of nonsequential site population allows a reinterpretation of existing experimental data....

  2. Electrocatalytic activity of surface adsorbed ruthenium-alizarin complexone toward the oxidation of benzyl alcohol

    Energy Technology Data Exchange (ETDEWEB)

    Marques, Aldalea Lopes Brandes; Li Weihua; Marques, Edmar Pereira; Zhang Jiujun

    2004-03-01

    The surface electrochemical behavior of an adsorbed alizarin complexone (abbreviated as AC) and its surface coordination with Ru(II) were studied in aqueous solution at a pH range of 0-6. The surface complex of ruthenium with AC displays strong electrocatalytic activities toward benzyl alcohol. Based on the rotating disk electrode measurement, it is believed that the electrocatalytic oxidation of benzyl alcohol is a two-electron and two-proton process with benzaldehyde as a major product. On the other hand, ruthenium-AC surface complex has also shown catalytic activities toward electro-oxidation of several small organic molecules such as methanol, formic acid, formaldehyde, ethanol, and acetaldehyde.

  3. XPS and NEXAFS analysis of dimethyl sulfide adsorbed on the Rh(PVP) nanoparticle surface

    International Nuclear Information System (INIS)

    Niwa, Hironori; Ogawa, Satoshi; Yagi, Shinya; Kutluk, Galif

    2010-01-01

    We have studied the adsorption reaction of dimethyl sulfide (DMS: (CH 3 ) 2 S) on the surface of Rh(PVP) nanoparticles by using AFM, XPS and NEXAFS techniques. The AFM images show the degree of dispersion of the Rh(PVP) nanoparticles depends on the amount of them. The in-situ XPS results indicate that the dissociation reaction of DMS into atomic S does not depend upon the existence of the Rh(PVP) nanoparticles. The NEXAFS results show that there is a strong chemical bonding between Rh(PVP) nanoparticle and atomic S. The ex-situ XPS results show the atomic S adsorbed on the Rh(PVP) nanoparticles partially desorb by exposing to the air. (author)

  4. Low-energy 4He+ scattering from deuterium adsorbed on stepped Pd(331)

    International Nuclear Information System (INIS)

    Ellis, W.P.; Bastasz, R.

    1996-01-01

    We have taken angle-resolved data for the scattering of low-energy ( 4 He + from deuterium adsorbed on a stepped Pd(331) surface. The impact geometry was up the staircase, that is, the 4 He + beam was perpendicular to and directly incident onto the unshadowed Pd ledge atoms. A strong quasi-elastic scattering signal of 4 He + from D ( 4 He + /D) was observed at a forward scattering angle of θ = 25 degrees and an incidence angle of α = 76 degrees from the (331) normal. The results agree with shadow cone calculations of scattering first from Pd ledge atoms followed by a second event, 4 He + /D. The resultant adsorption geometry shows D to reside in the quasi- threefold ledge site on the surface directly above the bulk fcc octahedral void. These results are consistent with the previous 4 He + scattering study of the geometrically related Pd(110)- D(ads) system

  5. Development Trends in Porous Adsorbents for Carbon Capture.

    Science.gov (United States)

    Sreenivasulu, Bolisetty; Sreedhar, Inkollu; Suresh, Pathi; Raghavan, Kondapuram Vijaya

    2015-11-03

    Accumulation of greenhouse gases especially CO2 in the atmosphere leading to global warming with undesirable climate changes has been a serious global concern. Major power generation in the world is from coal based power plants. Carbon capture through pre- and post- combustion technologies with various technical options like adsorption, absorption, membrane separations, and chemical looping combustion with and without oxygen uncoupling have received considerable attention of researchers, environmentalists and the stake holders. Carbon capture from flue gases can be achieved with micro and meso porous adsorbents. This review covers carbonaceous (organic and metal organic frameworks) and noncarbonaceous (inorganic) porous adsorbents for CO2 adsorption at different process conditions and pore sizes. Focus is also given to noncarbonaceous micro and meso porous adsorbents in chemical looping combustion involving insitu CO2 capture at high temperature (>400 °C). Adsorption mechanisms, material characteristics, and synthesis methods are discussed. Attention is given to isosteric heats and characterization techniques. The options to enhance the techno-economic viability of carbon capture techniques by integrating with CO2 utilization to produce industrially important chemicals like ammonia and urea are analyzed. From the reader's perspective, for different classes of materials, each section has been summarized in the form of tables or figures to get a quick glance of the developments.

  6. Distribution of metal and adsorbed guest species in zeolites

    Energy Technology Data Exchange (ETDEWEB)

    Chmelka, B.F.

    1989-12-01

    Because of their high internal surface areas and molecular-size cavity dimensions, zeolites are used widely as catalysts, shape- selective supports, or adsorbents in a variety of important chemical processes. For metal-catalyzed reactions, active metal species must be dispersed to sites within the zeolite pores that are accessible to diffusing reactant molecules. The distribution of the metal, together with transport and adsorption of reactant molecules in zeolite powders, are crucial to ultimate catalyst performance. The nature of the metal or adsorbed guest distribution is known, however, to be dramatically dependent upon preparatory conditions. Our objective is to understand, at the molecular level, how preparatory treatments influence the distribution of guest species in zeolites, in order that macroscopic adsorption and reaction properties of these materials may be better understood. The sensitivity of xenon to its adsorption environment makes {sup 129}Xe NMR spectroscopy an important diagnostic probe of metal clustering and adsorbate distribution processes in zeolites. The utility of {sup 129}Xe NMR depends on the mobility of the xenon atoms within the zeolite-guest system, together with the length scale of the sample heterogeneity being studied. In large pore zeolites containing dispersed guest species, such as Pt--NaY, {sup 129}Xe NMR is insensitive to fine structural details at room temperature.

  7. Shrimp pond wastewater treatment using pyrolyzed chicken feather as adsorbent

    Science.gov (United States)

    Moon, Wei Chek; Jbara, Mohamad Hasan; Palaniandy, Puganeshwary; Yusoff, Mohd Suffian

    2017-10-01

    In this study, chicken feather fiber was used as a raw material to prepare a non-expensive adsorbent by pyrolysis without chemical activation. The main pollutants treated in this study were chemical oxygen demand (COD) and ammoniacal nitrogen (NH3-N) from shrimp pond wastewater containing high concentrations of nutrients, which caused the eutrophication phenomenon in adjacent water. Batch adsorption studies were performed to investigate the effect of pH (5-8), mass of adsorbent (0.5-3 g), and shaking time (0.5-2 h) on the removal efficiency of COD and NH3- N. Experimental results showed that the optimum conditions were as follows: pH 5, 0.5 g of adsorbent, and 0.5 h of shaking. Under these conditions, 34.01% and 40.47% of COD and NH3-N were removed, respectively, from shrimp pond wastewater. The adsorption processes were best described by the Langmuir isotherm model for COD and NH3-N removal, with maximum monolayer adsorption capacity of 36.9 and 7.24 mg/g for COD and NH3-N, respectively. The results proved that chicken feather could remove COD and NH3-N from shrimp pond wastewater. However, further studies on thermal treatment should be carried out to increase the removal efficiency of pyrolyzed chicken feather fiber.

  8. Structural damages in adsorbed vaccines affected by freezing.

    Science.gov (United States)

    Kurzątkowski, Wiesław; Kartoğlu, Ümit; Staniszewska, Monika; Górska, Paulina; Krause, Aleksandra; Wysocki, Mirosław Jan

    2013-03-01

    This study was planned to evaluate structural damages in adsorbed vaccines affected by freezing using scanning electron microscopy and X-ray analysis of the elements. Randomly selected 42 vials of eight different types of WHO pre-qualified adsorbed freeze-sensitive vaccines from 10 manufacturers were included in the study. Vaccines were kept at 5 °C. Selected numbers of vials from each type were then exposed to -25 °C for 24 h periods. All samples were evaluated for their structure using scanning electron microscopy, X-ray analysis of the elements and precipitation time. Scanning electron microscopy of vaccines affected by freezing showed either smooth or rough surfaced conglomerates associated with phosphate content of the precipitate. These vaccines precipitated 2-15 times faster compared to non-frozen samples. Non-frozen samples showed uniform flocculent structure either dense or dispersed. X-ray analysis of precipitates in frozen samples confirmed that the precipitate is mainly aluminium clutters. Scanning electron microscopy confirmed that the lattice structure of bonds between adsorbent and the antigen is broken and aluminium forms conglomerates that grow in size and weight. The precipitation time of vaccines affected by freezing is 4.5 times faster on average compared to non-frozen samples. These facts form the basis of the "shake test". Copyright © 2012 World Health Organization. Published by Elsevier Ltd.. All rights reserved.

  9. Treatment of Refinery Waste Water Using Environmental Friendly Adsorbent

    Science.gov (United States)

    Devi, M. Geetha; Al-Moshrafi, Samira Mohammed Khamis; Al Hudaifi, Alaa; Al Aisari, Buthaina Hamood

    2017-12-01

    This research evaluates the effectiveness of activated carbon prepared from walnut shell in the removal of pollutants from refinery waste water by adsorption technique. A series of batch experiments were carried out by varying the effluent solution pH, stirring time, stirring speed and adsorbent dosage in the reduction of pollutants from refinery effluent. Characterization of the adsorbent was performed using Scanning Electron Microscopy (SEM), Brunauer Emmett and Teller (BET) isotherm and Fourier Transform Infrared (FTIR) Spectroscopy. The best quality activated carbon was obtained with a particle size of 0.75 µm, activation temperature of 800 °C and activation time 24 h. The maximum BET surface area obtained was 165.2653 m2/g. The experimental results demonstrates that the highest percentage reduction in COD was 79%, using 0.6 g walnut shell powder at an optimum stirring speed of 100 rpm, at pH 6 and 120 min of contact time. The outcome of the result shows that walnut shell carbon is a potentially useful adsorbent for the removal of pollutants from refinery waste water.

  10. Vanadium removal by metal (hydr)oxide adsorbents.

    Science.gov (United States)

    Naeem, A; Westerhoff, P; Mustafa, S

    2007-04-01

    Vanadium is listed on the United States Environment Protection Agency (USEPA) candidate contaminant list # 2 (CCL2), and regulatory guidelines for vanadium exist in some US states. The USEPA requires treatability studies before making regulatory decisions on CCL2 contaminants. Previous studies have examined vanadium adsorption onto some metal hydroxides but not onto commercially available adsorbents. This paper briefly summarizes known vanadium occurrence in North American groundwater and assesses vanadium removal by three commercially available metal oxide adsorbents with different mineralogies. GTO (Dow) is TiO2 based and E-33 (Seven Trents) and GFH (US Filter) are iron based. Preliminary vanadate adsorption kinetics onto GFH, E-33 and GTO has been studied and the homogenous surface diffusion model (HSDM) is used to describe the adsorption kinetics data. The effects of pH, vanadium concentration, and volume/mass ratio are assessed. Vanadium adsorption decreases with increasing pH, with maximum adsorption capacities achieved in at pH 3-4. Results indicate that all adsorbents remove vanadium; GFH has the highest adsorption capacity, followed by GTO and E-33. Data are best fit with the Langmuir model rather than Freundlich isotherms. Both the sorption maxima (Xm) and binding energy constant (b) follow the trend GFH>GTO>E-33. Naturally occurring vanadium is also removed from Arizona ground water in rapid small-scale column tests (RSSCTs). Metal oxide adsorption technologies currently used for arsenic removal may also remove vanadium but not always with the same effectiveness.

  11. Distribution of metal and adsorbed guest species in zeolites

    International Nuclear Information System (INIS)

    Chmelka, B.F.

    1989-12-01

    Because of their high internal surface areas and molecular-size cavity dimensions, zeolites are used widely as catalysts, shape- selective supports, or adsorbents in a variety of important chemical processes. For metal-catalyzed reactions, active metal species must be dispersed to sites within the zeolite pores that are accessible to diffusing reactant molecules. The distribution of the metal, together with transport and adsorption of reactant molecules in zeolite powders, are crucial to ultimate catalyst performance. The nature of the metal or adsorbed guest distribution is known, however, to be dramatically dependent upon preparatory conditions. Our objective is to understand, at the molecular level, how preparatory treatments influence the distribution of guest species in zeolites, in order that macroscopic adsorption and reaction properties of these materials may be better understood. The sensitivity of xenon to its adsorption environment makes 129 Xe NMR spectroscopy an important diagnostic probe of metal clustering and adsorbate distribution processes in zeolites. The utility of 129 Xe NMR depends on the mobility of the xenon atoms within the zeolite-guest system, together with the length scale of the sample heterogeneity being studied. In large pore zeolites containing dispersed guest species, such as Pt--NaY, 129 Xe NMR is insensitive to fine structural details at room temperature

  12. Specific binding-adsorbent assay method and test means

    International Nuclear Information System (INIS)

    1981-01-01

    A description is given of an improved specific binding assay method and test means employing a nonspecific adsorbent for the substance to be determined, particularly hepatitis B surface (HBsub(s)) antigen, in its free state or additionally in the form of its immune complex. The invention is illustrated by 1) the radioimmunoadsorbent assay for HBsub(s) antigen, 2) the radioimmunoadsorbent assay for HBsub(s) antigen in the form of immune complex with antibody, 3) a study of adsorption characteristics of various anion exchange materials for HBsub(s) antigen, 4) the use of hydrophobic adsorbents in a radioimmunoadsorbent assay for HBsub(s) antigen and 5) the radioimmunoadsorbent assay for antibody to HBsub(s) antigen. The advantages of the present method for detecting HBsub(s) antigen compared to previous methods include the manufacturing advantages of eliminating the need for insolubilised anti-HBsub(s) and the advantages of a single incubation step, fewer manipulations, storability of adsorbent materials, increased sensitivity and versatility of detecting HBsub(s) antigen in the form of its immune complex if desired. (U.K.)

  13. Strongly nonlinear dynamics of electrolytes in large ac voltages

    DEFF Research Database (Denmark)

    Olesen, Laurits Højgaard; Bazant, Martin Z.; Bruus, Henrik

    2010-01-01

    , ignoring any transverse instability or fluid flow. We analyze the resulting one-dimensional problem by matched asymptotic expansions in the limit of thin double layers and extend previous work into the strongly nonlinear regime, which is characterized by two features—significant salt depletion...... in the electrolyte near the electrodes and, at very large voltage, the breakdown of the quasiequilibrium structure of the double layers. The former leads to the prediction of “ac capacitive desalination” since there is a time-averaged transfer of salt from the bulk to the double layers, via oscillating diffusion...... to suppress the strongly nonlinear regime in the limit of concentrated electrolytes, ionic liquids, and molten salts. Beyond the model problem, our reduced equations for thin double layers, based on uniformly valid matched asymptotic expansions, provide a useful mathematical framework to describe additional...

  14. Determination of the adsorbent specific surface area at tar removing from industrial waste water of ammonium sulphate production

    Directory of Open Access Journals (Sweden)

    A.V. Ivanchenko

    2016-12-01

    Full Text Available At most coke plants of Ukraine and the world, ammonium sulphate (NH42SO4, which is an ammonium fertilizer, get in the department of trapping chemical products of coking. The liquid wastes formed in this department called phenolic wastewater, the main polluting agents of which are tarry substances. When choosing industrial adsorbent for wastewater treatment, the value of specific surface area is a determining factor. The high cost of modern industrial sorbents causes necessity of finding of new, more affordable their analogs, among which of particular interest are natural bentonite clays. Aim: The aim of research is to study the regularities of extraction process of tarry substances of manufacturing sewage of a ammonium sulphate with use of sodium and calcium bentonites, an absorbite and peat, and definition of a specific surface area of the specified adsorbents. Materials and Methods: In this study the absorbite AG-5, valley peat and natural sodium and calcium bentonite clays are used as sorbents. The adsorption of tar substances had been researched during the flotation process of phenolic wastewater in conditions close to industrial: the duration of flotation is 20 min; the wastewater temperature is 323 K; the intensity of air supply – 0.15 dm3/h. The calculations suggested that the adsorption of tarry substances is monomolecular in nature and described by the Langmuir’s theory of monomolecular adsorption. Results: The specific surface area of the adsorbents during the adsorption process of tarry substances from a phenolic industrial wastewater defined for the first time are following (m2/g: sodium bentonite clay – 1847; absorbite AG-5 – 1467; calcium bentonite clay – 728; valley peat – 603. For these adsorbents was also calculated the limit value of adsorption and constant of adsorption equilibria. The obtained values indicate a strong interaction between adsorbent and adsorbate, especially significant for the bentonite clay and

  15. Quantum electrodynamics of strong fields

    International Nuclear Information System (INIS)

    Greiner, W.

    1983-01-01

    Quantum Electrodynamics of Strong Fields provides a broad survey of the theoretical and experimental work accomplished, presenting papers by a group of international researchers who have made significant contributions to this developing area. Exploring the quantum theory of strong fields, the volume focuses on the phase transition to a charged vacuum in strong electric fields. The contributors also discuss such related topics as QED at short distances, precision tests of QED, nonperturbative QCD and confinement, pion condensation, and strong gravitational fields In addition, the volume features a historical paper on the roots of quantum field theory in the history of quantum physics by noted researcher Friedrich Hund

  16. Counting graphene layers with very slow electrons

    Energy Technology Data Exchange (ETDEWEB)

    Frank, Ludĕk; Mikmeková, Eliška; Müllerová, Ilona [Institute of Scientific Instruments AS CR, v.v.i., Královopolská 147, 61264 Brno (Czech Republic); Lejeune, Michaël [Laboratoire de Physique de la Matière Condensée, Faculté des Sciences d' Amiens, Universite de Picardie Jules Verne, 33 rue Saint Leu, 80039 Amiens Cedex 2 (France)

    2015-01-05

    The study aimed at collection of data regarding the transmissivity of freestanding graphene for electrons across their full energy scale down to the lowest energies. Here, we show that the electron transmissivity of graphene drops with the decreasing energy of the electrons and remains below 10% for energies below 30 eV, and that the slow electron transmissivity value is suitable for reliable determination of the number of graphene layers. Moreover, electrons incident below 50 eV release adsorbed hydrocarbon molecules and effectively clean graphene in contrast to faster electrons that decompose these molecules and create carbonaceous contamination.

  17. Network structure of collagen layers absorbed on LB film.

    Science.gov (United States)

    Chen, Qibin; Xu, Shouhong; Li, Rong; Liang, Xiaodong; Liu, Honglai

    2007-12-01

    Elucidating the assembly mechanism of the collagen at interfaces is important. In this work, the structures of type I collagen molecules adsorbed on bare mica and on LB films of propanediyl-bis(dimethyloctadecylammonium bromide) transferred onto mica at zero surface pressure was characterized by AFM. On mica, the granular morphologies randomly distributed as elongated structures were observed, which were resulted from the interlacement of the adsorbed collagen molecules. On the LB films, the topographical evolution of the adsorbed collagen layers upon the increasing adsorption time was investigated. After 30 s, the collagen assembled into network-like structure composed of the interwoven fibrils, called as the first adlayer, which was attributed to its adsorption on the LB film by means of a limited number of contact points followed by the lateral association. One minute later, the second adlayer was observed on the top of the first adlayer. Up to 5 min, collagen layers, formed by inter-twisted fibrils, were observed. Under the same conditions after 1 min adsorption on LB film, the AFM image of the layer obtained in the diluted hydrochloric acid solution is analogous to the result of the sample dried in air, indicating that it is the LB film that leads to the formation of the network structure of collagen and the formation of the network structures of collagen layers is tentatively ascribed to the self-assembly of type I collagen molecules on LB film, not to the dewetting of the collagen solution during drying.

  18. Foam-based adsorbents having high adsorption capacities for recovering dissolved metals and methods thereof

    Science.gov (United States)

    Janke, Christopher J.; Dai, Sheng; Oyola, Yatsandra

    2015-06-02

    Foam-based adsorbents and a related method of manufacture are provided. The foam-based adsorbents include polymer foam with grafted side chains and an increased surface area per unit weight to increase the adsorption of dissolved metals, for example uranium, from aqueous solutions. A method for forming the foam-based adsorbents includes irradiating polymer foam, grafting with polymerizable reactive monomers, reacting with hydroxylamine, and conditioning with an alkaline solution. Foam-based adsorbents formed according to the present method demonstrated a significantly improved uranium adsorption capacity per unit weight over existing adsorbents.

  19. QCM study of superfluid transition in 4He films adsorbed in SBA-15

    International Nuclear Information System (INIS)

    Matsuda, K; Hieda, M; Matsushita, T; Wada, N; Suzuki, T; Kuroda, K

    2009-01-01

    A quartz crystal microbalance (QCM) is a useful tool to study the superfluidity of 4 He films at very high frequencies. Our recent efforts to fabricate mesoporous silica films onto QCM have enabled us to study the noble superfluidity adsorbed in nanopores. In this paper we report results of QCM measurements for the superfluid 4 He films in SBA-15 with one-dimensional nanopores 4.1 nm in diameter and ∼ 1 μM in length. From the 4 He pressure isotherm at 4.2 K, a uniform layer is formed in the nanopores up to the coverage of 48 μmol/m 2 , corresponding to ∼ 2.5 layers. The superfluid response is measured at 12 MHz for various coverages in the temperature range of 0.1 - 1.5 K. Above the onset coverage of ∼ 23 μmol/m 2 , we observed a frequency shift accompanied by a dissipation peak due to the superfluid Kosterlitz-Thouless (KT) transition.

  20. Characterization of LSM/CGO Symmetric Cells Modified by NOx Adsorbents for Electrochemical NOx Removal with Impedance Spectroscopy

    DEFF Research Database (Denmark)

    Shao, Jing; Kammer Hansen, Kent

    2013-01-01

    This study uses electrochemical impedance spectroscopy (EIS) to characterize an LSM/CGO symmetric cell modified by NOx adsorbents for the application of electrochemical NOx reduction. Three cells were prepared and tested: a blank cell, a cell impregnated with BaO, and a cell coated with a Ba......O-Pt-Al2O3 layer. The impedance analysis revealed that modification with the NOx adsorbents, either by impregnating the BaO into the electrode or by adding a BaO-Pt-Al2O3 layer on top of the electrode significantly enhanced the electrode activity. This activity enhancement was mainly due to the decrease...... in the resistance of the low-frequency processes, which were ascribed to adsorption, diffusion, and transfer of O2 species and NOx species at or near the triple phase boundary (TPB) region and the formation of the reaction intermediate NO2. The BaO impregnation improved the adsorption of NOx on the LSM...

  1. Strong WW Interaction at LHC

    Energy Technology Data Exchange (ETDEWEB)

    Pelaez, Jose R

    1998-12-14

    We present a brief pedagogical introduction to the Effective Electroweak Chiral Lagrangians, which provide a model independent description of the WW interactions in the strong regime. When it is complemented with some unitarization or a dispersive approach, this formalism allows the study of the general strong scenario expected at the LHC, including resonances.

  2. Theory of third sound in a compressible and layered superfluid

    International Nuclear Information System (INIS)

    Puff, R.D.; Dash, J.G.

    1980-01-01

    This paper examines the theory of third sound, without attenuation effects, in layered superfluid films with finite compressibility. This theory, together with the application of a simple thermodynamic model for the film layers shows how the third-sound velocity can undergo strong variations with coverage associated with progressive changes in film compressibility, in-layer phase changes, and layer completion

  3. Design and performance prediction of a new generation adsorption chiller using composite adsorbent

    International Nuclear Information System (INIS)

    Gong, L.X.; Wang, R.Z.; Xia, Z.Z.; Chen, C.J.

    2011-01-01

    Research highlights: → Composite adsorbent 'employing lithium chloride in silica gel' and water as working pair. → A new type adsorbent bed is used to accommodate the composite adsorbent. → A dynamic model of the adsorption chiller is built. → The coefficient of performance (COP) and the cooling capacity will be improved. -- Abstract: This paper presents a novel adsorption chiller using composite adsorbent 'employing lithium chloride in silica gel' as adsorbent and water as adsorbate. A new type adsorbent bed is used to accommodate the composite adsorbent. The mass recovery between two adsorbent beds usually results in the adsorbate unbalance. So a novel auto water makeup unite is used to solve the problem. A dynamic model of the adsorption chiller is built based on the adsorption isotherms to predict the performance. The simulation result shows that the coefficient of performance (COP) and the cooling capacity will increase by using this new composite adsorbent. When the temperatures of hot water inlet, cooling water inlet, and chilled water inlet are 363, 303 and 293 K, COP will be 0.43, and the cooling capacity will be 5.295 kW. Also operation strategy is optimized. Different temperatures of hot water inlet, cooling water inlet and chilling water inlet will result in different COP and cooling capacity.

  4. Nanoscale colloids in a freely adsorbing polymer solution: a Monte Carlo simulation study.

    Science.gov (United States)

    Marla, Krishna Tej; Meredith, J Carson

    2004-02-17

    exponent for gamma (gamma approximately n(p)). This result leads to the conclusion that in attractive systems, polymer adsorption (and thus polymer-colloid attraction) dominates the micro(c) dependence on n, providing a molecular interpretation of the effect of adsorbed organic layers on nanoparticle stability and self-assembly.

  5. Strong-back safety latch

    International Nuclear Information System (INIS)

    DeSantis, G.N.

    1995-01-01

    The calculation decides the integrity of the safety latch that will hold the strong-back to the pump during lifting. The safety latch will be welded to the strong-back and will latch to a 1.5-in. dia cantilever rod welded to the pump baseplate. The static and dynamic analysis shows that the safety latch will hold the strong-back to the pump if the friction clamps fail and the pump become free from the strong-back. Thus, the safety latch will meet the requirements of the Lifting and Rigging Manual for under the hook lifting for static loading; it can withstand shock loads from the strong-back falling 0.25 inch

  6. Strong-back safety latch

    Energy Technology Data Exchange (ETDEWEB)

    DeSantis, G.N.

    1995-03-06

    The calculation decides the integrity of the safety latch that will hold the strong-back to the pump during lifting. The safety latch will be welded to the strong-back and will latch to a 1.5-in. dia cantilever rod welded to the pump baseplate. The static and dynamic analysis shows that the safety latch will hold the strong-back to the pump if the friction clamps fail and the pump become free from the strong-back. Thus, the safety latch will meet the requirements of the Lifting and Rigging Manual for under the hook lifting for static loading; it can withstand shock loads from the strong-back falling 0.25 inch.

  7. AC microcalorimetry of adsorbates on evaporated metal films: Orientational ordering of H2 multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Phelps, Robert Bloss [Univ. of California, Berkeley, CA (United States)

    1991-11-01

    We have improved and extended a novel ac calorimetric technique for measuring the heat capacity of adsorbates on evaporated metal films. Metallic substrates are of particular interest in current studies of the thermodynamics of adsorbed molecules. The method described in the present work is only calorimetric technique which allows measurements of molecules on simple metallic surfaces. Among other improvements, we have achieved significant progress in the preparation and characterization of the evaporated metal film. We have applied this novel technique to a study of hydrogen multilayers on gold and sapphire substrates. We have shown that samples of normal-hydrogen with a nominal coverage n of approximately 25 monolayers (ML) undergo a bulk-like orientational ordering transition. The transition is suppressed as the coverage is decreased, and no sign of the transition remains above 1.6 K for n ~ 1 ML. For n ≲ 8 ML, the peak in the heat capacity exhibits signs of finite-size effects. At higher coverages, finite-size effects are not observed, and the shape of the peak depends strongly on the substrate. We conclude that the peak is inhomogeneously broadened for n ≲ 8 ML. This work represents the first measurements of the heat capacity due to orientational ordering in adsorbed hydrogen. The results of an earlier experiment involving vibrational spectroscopy of adsorbed molecules are included in the Appendix. In this work, we have used infrared emission spectroscopy to study the spectral region in the vicinity of the C=O stretch vibration of bridge-bonded CO on Pt(111).

  8. Current status of adsorbent for metal ions with radiation grafting and crosslinking techniques

    Science.gov (United States)

    Seko, Noriaki; Tamada, Masao; Yoshii, Fumio

    2005-07-01

    Removal of toxic metals from streaming water and ground water is important task to preserve environment. Radiation processing of grafting and crosslinking can synthesis adsorbent having high performances. Graft adsorbent can be synthesized by using the conventional polymer like polyethylene having variety shapes such as membrane, cloth, and fiber. Especially, the obtained fibrous adsorbent has 100 times higher rate of adsorption than that of commercialized resin. Fibrous adsorbent of iminodiacetate was applied to the removal of cadmium from the scallop waste. Furthermore, the amidoxime adsorbent is useful for recovery of rare metals such as uranium and vanadium in seawater. Novel fibrous adsorption for arsenic was synthesized by direct grafting of phosphoric monomer and following zirconium-loading. Crosslinked natural polymers like carboxymethyl chitin-chitosan in the paste-like state are applicable for the metal adsorbent. This adsorbent can be biodegraded after usage.

  9. Surface enhanced raman spectroscopy on nucleic acids and related compounds adsorbed on colloidal silver particles

    Science.gov (United States)

    Kneipp, K.; Pohle, W.; Fabian, H.

    1991-04-01

    Various nucleic acids and related compounds have been investigated by surface enhanced Raman spectroscopy (SERS) on silver sol. The time delay between the addition of the various nucleic acids to the silver sol and the appearance of their SER spectra, i.e. the time needed by the various molecules to adsorb on an active site of the silver surface with an adsorption geometry which allows a SERS enhancement, shows strong differences. For instance, an immediate appearance of SER spectra has been found for DNA, whereas ribonucleic acids (RNAs) demonstrated a strong time delay (up to days) of the appearance of their SER spectra. This delay can be tentatively explained by the higher rigidity of RNA molecules compared with DNA. The more flexible DNA molecules are better adaptable to adsorption on silver than RNAs. The SER spectra of RNAs and DNAs showed strong changes within their relative line intensities as a function of time before they achieved stationary conditions, which indicates a protracted re-arrangement of the large molecules on the silver surface.

  10. Potential of polyaniline modified clay nanocomposite as a selective decontamination adsorbent for Pb(II) ions from contaminated waters; kinetics and thermodynamic study.

    Science.gov (United States)

    Piri, Somayeh; Zanjani, Zahra Alikhani; Piri, Farideh; Zamani, Abbasali; Yaftian, Mohamadreza; Davari, Mehdi

    2016-01-01

    Nowadays significant attention is to nanocomposite compounds in water cleaning. In this article the synthesis and characterization of conductive polyaniline/clay (PANI/clay) as a hybrid nanocomposite with extended chain conformation and its application for water purification are presented. Clay samples were obtained from the central plain of Abhar region, Abhar, Zanjan Province, Iran. Clay was dried and sieved before used as adsorbent. The conductive polyaniline was inflicted into the layers of clay to fabricate a hybrid material. The structural properties of the fabricated nanocomposite are studied by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscope (SEM). The elimination process of Pb(II) and Cd(II) ions from synthetics aqueous phase on the surface of PANI/clay as adsorbent were evaluated in batch experiments. Flame atomic absorption instrument spectrophotometer was used for determination of the studied ions concentration. Consequence change of the pH and initial metal amount in aqueous solution, the procedure time and the used adsorbent dose as the effective parameters on the removal efficiency was investigated. Surface characterization was exhibited that the clay layers were flaked in the hybrid nanocomposite. The results show that what happen when a nanocomposite polyaniline chain is inserted between the clay layers. The adsorption of ions confirmed a pH dependency procedure and a maximum removal value was seen at pH 5.0. The adsorption isotherm and the kinetics of the adsorption processes were described by Temkin model and pseudo-second-order equation. Time of procedure, pH and initial ion amount have a severe effect on adsorption efficiency of PANI/clay. By using suggested synthesise method, nano-composite as the adsorbent simply will be prepared. The prepared PANI/clay showed excellent adsorption capability for decontamination of Pb ions from contaminated water. Both of suggested synthesise and

  11. Titanium: light, strong, and white

    Science.gov (United States)

    Woodruff, Laurel; Bedinger, George

    2013-01-01

    Titanium (Ti) is a strong silver-gray metal that is highly resistant to corrosion and is chemically inert. It is as strong as steel but 45 percent lighter, and it is twice as strong as aluminum but only 60 percent heavier. Titanium dioxide (TiO2) has a very high refractive index, which means that it has high light-scattering ability. As a result, TiO2 imparts whiteness, opacity, and brightness to many products. ...Because of the unique physical properties of titanium metal and the whiteness provided by TiO2, titanium is now used widely in modern industrial societies.

  12. Adsorptivity of uranium by aluminium-activated carbon composite adsorbent

    International Nuclear Information System (INIS)

    Katoh, Shunsaku; Sugasaka, Kazuhiko; Fujii, Ayako; Takagi, Norio; Miyai, Yoshitaka

    1976-01-01

    To research the adsorption process of uranium from sea water by aluminium-activated carbon composite adsorbent (C-Al-OH), the authors examined the effects of temperature, pH and carbonate ion concentration of the solution upon the adsorption of uranium, using sodium chloride solution and natural sea water. The continued mixing of the solution for the duration of two to four hours was required to attain the apparent equilibrium of adsorption. The adsorption velocity at an early stage and the uptake of uranium at the final stage showed an increase in proportion to a rise in the adsorption temperature. In the experiment of adsorption for which sodium chloride solution was used, the linear relationship between the logarithm of the distribution coefficient (K sub(d)) and the pH of the solution was recognized. The uptake of the uranium from the solution at the pH of 12 increased as the carbonate ion concentration in the solution decreased. The uranyl ion in the natural sea water was assumed to be uranyl carbonate complex ion (UO 2 (CO 3 ) 3 4- ). As the result of the calculation conducted by using the formation constants for uranyl complexes in literature, it was found that uranyl hydroxo complex ion (UO 2 (OH) 3 - ) increased in line with a decrease of the carbonate ion concentration in the solution. The above results of the experiment suggested that the adsorption of uranium by the adsorbent (C-Al-OH) was cationic adsorption or hydrolysis adsorption being related with the active proton on the surface of the adsorbent. (auth.)

  13. Ultrafast electron dynamics at alkali/ice structures adsorbed on a metal surface

    International Nuclear Information System (INIS)

    Meyer, Michael

    2011-01-01

    The goal of this work is to study the interaction between excess electrons in water ice structures adsorbed on metal surfaces and other charged or neutral species, like alkali ions, or chemically reactive molecules, like chlorofluorocarbons (CFC), respectively. The excess electrons in the ice can interact with the ions directly or indirectly via the hydrogen bonded water molecules. In both cases the presence of the alkali influences the population, localization, and lifetime of electronic states of excess electrons in the ice adlayer. These properties are of great relevance when considering the highly reactive character of the excess electrons, which can mediate chemical reactions by dissociative electron attachment (DEA). The influence of alkali adsorption on electron solvation and transfer dynamics in ice structures is investigated for two types of adsorption configurations using femtosecond time-resolved two-photon photoelectron spectroscopy. In the first system alkali atoms are coadsorbed on top of a wetting amorphous ice film adsorbed on Cu(111). At temperatures between 60 and 100 K alkali adsorption leads to the formation of positively charged alkali ions at the ice/vacuum interface. The interaction between the alkali ions at the surface and the dipole moments of the surrounding water molecules results in a reorientation of the water molecules. As a consequence new electron trapping sites, i.e. at local potential minima, are formed. Photoinjection of excess electrons into these alkali-ion covered amorphous ice layers, results in the trapping of a solvated electron at an alkali-ion/water complex. In contrast to solvation in pure amorphous ice films, where the electrons are located in the bulk of the ice layer, solvated electrons at alkali-ion/water complexes are located at the ice/vacuum interface. They exhibit lifetimes of several picoseconds and show a fast energetic stabilization. With ongoing solvation, i.e. pump-probe time delay, the electron transfer is

  14. Analysis of viscous losses in the chemical interface layer of Love wave sensors.

    Science.gov (United States)

    Jakoby, B; Vellekoop, M J

    2000-01-01

    Love waves have been introduced as highly effective devices for liquid-sensing applications. For chemical sensors, a microacoustic delay line featuring a multilayered waveguide supporting a generalised Love wave mode can be used in an oscillator setup. The top layer of the waveguide is a chemical interface, which selectively adsorbs certain target molecules in the adjacent liquid. The increase in mass density caused by adsorption can be detected as changes in the oscillation frequency. Commonly used interface materials show viscoelastic losses leading to an unwanted damping of the wave. To keep the signal-to-noise ratio high, the total insertion loss of the delay line should be kept as low as possible. Furthermore, it must not exceed a certain value to allow the electronic circuitry to sustain the oscillation. We analyzed the viscoelastic losses, which strongly depend on the frequency being used. By means of the proposed theoretical approach, the maximum thickness of the interface layer can be determined not to exceed the losses that can be handled by the driving electronics.

  15. Removing 3,5-Dichlorophenol from Wastewater by Alternative Adsorbents

    Directory of Open Access Journals (Sweden)

    Kobetičová Hana

    2014-12-01

    Full Text Available The main objective of this paper is to evaluate an efficiency of 3,5 - dichlorophenol removal from wastewater by using alternative adsorbents. Chlorophenols are organic compounds consisting of a benzene ring, OH groups and also atoms of chlorine. Chlorophenols may have a huge isomere variety that means there are differences in their chemical and physical properties. Due to their toxicity it is necessary to remove them from waste water and in this paper an alternative way of such process is described.

  16. Silicalite-1, an adsorbent for 2-, 3-, and 4-chlorophenols.

    Science.gov (United States)

    Sánchez-Flores, N A; Solache, M; Olguín, M T; Legaspe, J; Pacheco-Malagón, G; Saniger, J M; Martinez, E; Bulbulian, S; Fripiat, J J

    2012-01-01

    The adsorption of the three chlorophenol isomers, ortho, meta and para, by silicalite-1 has been studied at 30 °C, below the solubility (at the same temperature) in water. Large differences, up to 30 times, have been observed between the adsorption of the para- vs. the ortho-isomer. The difference of behavior observed between the isomers is assigned to the tendency to self-organization of the para-isomer. It seems probable that the adsorption sites are at the intersection channels. From a technical point of view, silicalite-1 seems a competitive adsorbent for p-chlorophenol.

  17. 3,5-Dichlorophenol Removal From Wastewater Using Alternative Adsorbents

    Directory of Open Access Journals (Sweden)

    Kobetičová Hana

    2015-06-01

    Full Text Available The main objective of this paper is to evaluate the efficiency of 3,5-dichlorophenol removal from wastewater by using alternative low cost adsorbents. Waste from the production and processing of metals (black nickel mud, red mud and a biosorbent (Lemna minor were used for this research. Initial concentration of the contaminant was 4 mmol L−1, the contact time of sorbent and waste water was 0 - 48 hrs and the temperature during experiment was 25 ± 0.2 °C. The results show that the highest removal efficiency of 3,5 - dichlorophenol (58.18 % was reached by the red mud in 48 hours.

  18. Controllable Catalysis with Nanoparticles: Bimetallic Alloy Systems and Surface Adsorbates

    KAUST Repository

    Chen, Tianyou

    2016-05-16

    Transition metal nanoparticles are privileged materials in catalysis due to their high specific surface areas and abundance of active catalytic sites. While many of these catalysts are quite useful, we are only beginning to understand the underlying catalytic mechanisms. Opening the “black box” of nanoparticle catalysis is essential to achieve the ultimate goal of catalysis by design. In this Perspective we highlight recent work addressing the topic of controlled catalysis with bimetallic alloy and “designer” adsorbate-stabilized metal nanoparticles.

  19. Detection of adsorbed water and hydroxyl on the Moon.

    Science.gov (United States)

    Clark, Roger N

    2009-10-23

    Data from the Visual and Infrared Mapping Spectrometer (VIMS) on Cassini during its flyby of the Moon in 1999 show a broad absorption at 3 micrometers due to adsorbed water and near 2.8 micrometers attributed to hydroxyl in the sunlit surface on the Moon. The amounts of water indicated in the spectra depend on the type of mixing and the grain sizes in the rocks and soils but could be 10 to 1000 parts per million and locally higher. Water in the polar regions may be water that has migrated to the colder environments there. Trace hydroxyl is observed in the anorthositic highlands at lower latitudes.

  20. 3,5-Dichlorophenol Removal From Wastewater Using Alternative Adsorbents

    Science.gov (United States)

    Kobetičová, Hana; Lipovský, Marek; Wachter, Igor; Soldán, Maroš

    2015-06-01

    The main objective of this paper is to evaluate the efficiency of 3,5-dichlorophenol removal from wastewater by using alternative low cost adsorbents. Waste from the production and processing of metals (black nickel mud, red mud) and a biosorbent (Lemna minor) were used for this research. Initial concentration of the contaminant was 4 mmol L-1, the contact time of sorbent and waste water was 0 - 48 hrs and the temperature during experiment was 25 ± 0.2 °C. The results show that the highest removal efficiency of 3,5 - dichlorophenol (58.18 %) was reached by the red mud in 48 hours.

  1. Corrected electrostatic model for dipoles adsorbed on a metal surface

    Energy Technology Data Exchange (ETDEWEB)

    Maschhoff, B.L.; Cowin, J.P. (Enviornmental and Molecular Science Laboratory, Pacific Northwest Laboratories Box 999 MS K2-14, Richland, Washington 99352 (United States))

    1994-11-01

    We present a dipole--dipole interaction model for polar molecules vertically adsorbed on a idealized metal surface in an approximate analytic form suitable for estimating the coverage dependence of the work function, binding energies, and thermal desorption activation energies. In contrast to previous treatments, we have included all contributions to the interaction energy within the dipole model, such as the internal polarization energy and the coverage dependence of the self-image interaction with the metal. We show that these can contribute significantly to the total interaction energy. We present formulae for both point and extended dipole cases.

  2. Individual and combined effects of water quality and empty bed contact time on As(V) removal by a fixed-bed iron oxide adsorber: implication for silicate precoating.

    Science.gov (United States)

    Kanematsu, Masakazu; Young, Thomas M; Fukushi, Keisuke; Green, Peter G; Darby, Jeannie L

    2012-10-15

    The individual and combined effects of changes in water quality (i.e. pH, initial concentrations of arsenate (As(V)) and competing ions) and empty bed contact time (EBCT) on As(V) removal performance of a fixed-bed adsorber (FBA) packed with a nanostructured goethite-based granular porous adsorbent were systematically studied under environmentally relevant conditions. Rapid small scale column tests (RSSCTs) were extensively conducted at different EBCTs with synthetic waters in which pH and the concentrations of competing ions (phosphate, silicate, and vanadate) were controlled. In the absence of the competing ions, the effects of initial As(V) concentration, pH, and EBCT on As(V) breakthrough curves were successfully predicted by the homogeneous surface diffusion model (HSDM) with adsorption isotherms predicted by the extended triple layer model (ETLM). The interference effects of silicate and phosphate on As(V) removal were strongly influenced by pH, their concentrations, and EBCT. In the presence of silicate (≤21 mg/L as Si), a longer EBCT surprisingly resulted in worse As(V) removal performance. We suggest this is because silicate, which normally exists at much higher concentration and moves more quickly through the bed than As(V), occupies or blocks adsorption sites on the media and interferes with later As(V) adsorption. Here, an alternative operating scheme of a FBA for As(V) removal is proposed to mitigate the silicate preloading. Silicate showed a strong competing effect to As(V) under the tested conditions. However, as the phosphate concentration increased, its interference effect dominated that of silicate. High phosphate concentration (>100 μg/L as P), as experienced in some regions, resulted in immediate As(V) breakthrough. In contrast to the observation in the presence of silicate, longer EBCT resulted in improved As(V) removal performance in the presence of phosphate. Vanadate was found to compete with As(V) as strongly as phosphate. This study

  3. Synthesis of pellet-type red mud adsorbents for removal of heavy metal ions

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jung-Sik; Han, Sang-Won; Hwang, In-Gook; Bae, Jae-Heum; Choi, Woo-Zin [The University of Suwon, Whasung(Korea)

    2000-02-28

    Red mud is generated as a by-product in the production of Al(OH){sub 3}/Al{sub 2}O{sub 3} from bauxite ore. In this study the pellet-type adsorbents have been made from the red mud, and their adsorption capacities of heavy metal ions have been tested. The pellet-type adsorbents were synthesized to utilize the excellent adsorption capacity of the powder-type adsorbent for industrial application. The pellet-type adsorbents were prepared by mixing several kinds of additives with the red mud. It is found that the pellet-type adsorbent, made by sintering a mixture of red mud (96.0 wt%), polypropylene (2.5 wt%), fly ash (0.5 wt%), and sodium meta-silicate (1.0 wt%) at 1200 deg.C for 30 minutes, has the highest adsorption capacity. In this work, the two kinds of pellet-type adsorbents (bead-type, crushed-type) were prepared. The crushed-type adsorbent was found to show a better adsorption/desorption performance than the bead-type adsorbent. The crushed-type adsorbent showed a good adsorption capacity of Pb{sup 2+} like the powder-type adsorbent. (author). 13 refs., 5 tabs., 13 figs.

  4. Ochratoxin A removal from red wine by several oenological fining agents: bentonite, egg albumin, allergen-free adsorbents, chitin and chitosan.

    Science.gov (United States)

    Quintela, S; Villarán, M C; López De Armentia, I; Elejalde, E

    2012-01-01

    The ability of several oenological fining agents to remove ochratoxin A (OTA) from red wine was studied. The adsorbents tested were activated sodium bentonite, egg albumin, allergen-free adsorbents (complex PVPP, plant protein and amorphous silica (complex) and high molecular weight gelatine), and the non-toxic biodegradable polymers (chitin and chitosan). Several dosages within the oenological use range were tested and the wine pH, colour parameters and polyphenol concentration impact associated with each fining agent were studied. Generally, OTA removal achieved in all treatments was higher when the adsorbent dosage increased, but the impact on wine quality also was higher. Chitin at 50 g hl(-1) removed 18% the OTA without affecting significantly the wine-quality parameters. At the highest dosage tested the gelatine and complex treatments achieved greater OTA removal (up to 39-40%) compared with bentonite, egg albumin and chitin. Moreover, the gelatine and the complex had a lower impact on colour parameters and polyphenol concentration compared with chitosan, whilst OTA was reduced to around 40%. Chitosan achieved the greatest OTA removal (67%), but it strongly affected the wine-quality parameters. Otherwise, bentonite showed a relative efficiency to remove OTA, but the CI value decreased considerably. The egg albumin treatment only removed OTA up to 16% and moreover affected strongly the CI value and CIELab parameters. The results of this survey showed that the non-toxic chitin adsorbent and the allergen-free adsorbents tested could be considered as alternative fining agents to reduce OTA in red wine.

  5. Cd(II) adsorption on various adsorbents obtained from charred biomaterials.

    Science.gov (United States)

    Li, Zhenze; Katsumi, Takeshi; Imaizumi, Shigeyoshi; Tang, Xiaowu; Inui, Toru

    2010-11-15

    Cadmium could cause severe toxicant impact to living beings and is especially mobile in the environment. Biomass is abundant and effective to adsorb heavy metals, but is easy to be decomposed biologically which affects the reliability of long-run application. Several biomasses were charred with and without additives at temperatures less than 200°C in this study. The prepared adsorbents were further testified to remove Cd(II) from aqueous solution. Equilibrium and kinetic studies were performed in batch conditions. The effect of several experimental parameters on the cadmium adsorption kinetics namely: contact time, initial cadmium concentration, sorbent dose, initial pH of solution and ionic strength was evaluated. Kinetic study confirmed (1) the rapid adsorption of Cd(II) on GC within 10 min and (2) the following gradual intraparticle diffusion inwards the sorbent at neutral pH and outwards at strong acidic solution. The grass char (GC) was selected for further test according to its high adsorption capacity (115.8 mg g(-1)) and affinity (Langmuir type isotherm). The Cd(II) removal efficiency was increased with increasing solution pH while the highest achieved at sorbent dosage 10.0 g L(-1). The ionic strength affects the sorption of Cd(II) on GC to a limited extent whereas calcium resulted in larger competition to the sorption sites than potassium. Spectroscopic investigation revealed the adsorption mechanisms between Cd(II) and surface functional groups involving amine, carboxyl and iron oxide. The long-term stability of the pyrolyzed grass char and the potential application in engineering practices were discussed. Copyright © 2010 Elsevier B.V. All rights reserved.

  6. Cd(II) adsorption on various adsorbents obtained from charred biomaterials

    International Nuclear Information System (INIS)

    Li Zhenze; Katsumi, Takeshi; Imaizumi, Shigeyoshi; Tang Xiaowu; Inui, Toru

    2010-01-01

    Cadmium could cause severe toxicant impact to living beings and is especially mobile in the environment. Biomass is abundant and effective to adsorb heavy metals, but is easy to be decomposed biologically which affects the reliability of long-run application. Several biomasses were charred with and without additives at temperatures less than 200 deg. C in this study. The prepared adsorbents were further testified to remove Cd(II) from aqueous solution. Equilibrium and kinetic studies were performed in batch conditions. The effect of several experimental parameters on the cadmium adsorption kinetics namely: contact time, initial cadmium concentration, sorbent dose, initial pH of solution and ionic strength was evaluated. Kinetic study confirmed (1) the rapid adsorption of Cd(II) on GC within 10 min and (2) the following gradual intraparticle diffusion inwards the sorbent at neutral pH and outwards at strong acidic solution. The grass char (GC) was selected for further test according to its high adsorption capacity (115.8 mg g -1 ) and affinity (Langmuir type isotherm). The Cd(II) removal efficiency was increased with increasing solution pH while the highest achieved at sorbent dosage 10.0 g L -1 . The ionic strength affects the sorption of Cd(II) on GC to a limited extent whereas calcium resulted in larger competition to the sorption sites than potassium. Spectroscopic investigation revealed the adsorption mechanisms between Cd(II) and surface functional groups involving amine, carboxyl and iron oxide. The long-term stability of the pyrolyzed grass char and the potential application in engineering practices were discussed.

  7. Multilayer bonding using a conformal adsorbate film (CAF) for the fabrication of 3D monolithic microfluidic devices in photopolymer

    Science.gov (United States)

    Gutierrez-Rivera, L.; Martinez-Quijada, J.; Johnstone, R.; Elliott, D.; Backhouse, C.; Sameoto, D.

    2012-08-01

    Reliable microfabrication processes and materials compatible with complementary metal-oxide semiconductor (CMOS) technology are required by industry for the mass production of complex and highly miniaturized lab-on-a-chip systems. Photopolymers are commonly used in the semiconductor industry, and are suitable for the integration of multilayer structures onto CMOS substrates. This paper describes a novel photopolymer bonding process compatible with CMOS technology for the fabrication of three-dimensional monolithic microfluidic devices. The process consists of the formation of a conformal adsorbate film (CAF) approximately 15 nm thick on a patterned photopolymer layer (KMPR), thereby increasing the number of open polymer chains at the bonding interface and acting as an ultra-thin adhesive layer. This thin adhesive layer is made of the same photopolymer as the microfluidic structures, but has a substantially lower crosslinking density so it will be able to make better bonds during a thermocompressive bonding step. This CAF treatment substantially improves the bonding yield between two patterned and previously crosslinked photopolymer layers because both optimum structure strength (to resist deformation during bonding) and bonding strength from epoxy crosslinking can be achieved. We demonstrate high bonding yields of up to 99% of the useful area of the substrate after three successive bonding steps. With this technique, up to six layers have been bonded in a single device. Unlike previously reported methods the quality of bonding is mostly decoupled from soft-bake parameters and crosslinking level of the previously patterned layers. Three differentbonding processes were characterized to describe the bonding mechanism and the differences between the presented method and the partial-crosslinking bonding method. Capillary filling experiments were performed in microchannels of multilayer structures built with the CAF technique, without any observable leakage between

  8. Waste metal hydroxide sludge as adsorbent for a reactive dye.

    Science.gov (United States)

    Santos, Sílvia C R; Vílar, Vítor J P; Boaventura, Rui A R

    2008-05-30

    An industrial waste sludge mainly composed by metal hydroxides was used as a low-cost adsorbent for removing a reactive textile dye (Remazol Brilliant Blue) in solution. Characterization of this waste material included chemical composition, pH(ZPC) determination, particle size distribution, physical textural properties and metals mobility under different pH conditions. Dye adsorption equilibrium isotherms were determined at 25 and 35 degrees C and pH of 4, 7 and 10 revealing reasonably fits to Langmuir and Freundlich models. At 25 degrees C and pH 7, Langmuir fit indicates a maximum adsorption capacity of 91.0mg/g. An adsorptive ion-exchange mechanism was identified from desorption studies. Batch kinetic experiments were also conducted at different initial dye concentration, temperature, adsorbent dosage and pH. A pseudo-second-order model showed good agreement with experimental data. LDF approximation model was used to estimate homogeneous solid diffusion coefficients and the effective pore diffusivities. Additionally, a simulated real effluent containing the selected dye, salts and dyeing auxiliary chemicals, was also used in equilibrium and kinetic experiments and the adsorption performance was compared with aqueous dye solutions.

  9. Liquid-Cell Electron Microscopy of Adsorbed Polymers.

    Science.gov (United States)

    Nagamanasa, Kandula Hima; Wang, Huan; Granick, Steve

    2017-11-01

    Individual macromolecules of polystyrene sulfonate and poly(ethylene oxide) are visualized with nanometer resolution using transmission electron microscopy (TEM) imaging of aqueous solutions with and without added salt, trapped in liquid pockets between creased graphene sheets. Successful imaging with 0.3 s per frame is enabled by the sluggish mobility of the adsorbed molecules. This study finds, validating others, that an advantage of this graphene liquid-cell approach is apparently to retard sample degradation from incident electrons, in addition to minimizing background scattering because graphene windows are atomically thin. Its new application here to polymers devoid of metal-ion labeling allows the projected sizes and conformational fluctuations of adsorbed molecules and adsorption-desorption events to be analyzed. Confirming the identification of the observed objects, this study reports statistical analysis of datasets of hundreds of images for times up to 100 s, with variation of the chemical makeup of the polymer, the molecular weight of the polymer, and the salt concentration. This observation of discrete polymer molecules in solution environment may be useful generally, as the findings are obtained using an ordinary TEM microscope, whose kind is available to many researchers routinely. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Fly ash adsorbents for multi-cation wastewater treatment

    Energy Technology Data Exchange (ETDEWEB)

    Visa, Maria, E-mail: maria.visa@unitbv.ro [Transilvania University of Brasov, Dept. Renewable Energy Systems and Recycling, Eroilor 29, 500036 Brasov (Romania); Isac, Luminita; Duta, Anca [Transilvania University of Brasov, Dept. Renewable Energy Systems and Recycling, Eroilor 29, 500036 Brasov (Romania)

    2012-06-15

    Class 'F' fly ash (FA), collected from the Central Heat and Power (CHP) Plant Brasov (Romania), with oxides composition SiO{sub 2}/Al{sub 2}O{sub 3} over 2.4 proved good adsorbent properties, and was further used for obtaining a new substrate with good adsorption capacity for heavy metals from multi-cation wastewater treatment. Firstly, the new adsorbent was characterized by AFM, XRD, DSC, FTIR and the surface energy was evaluated by contact angle measurements. The experimental data suggested that the new type of substrate is predominant crystalline with highly polar surface. The substrate was used for removing the Pb{sup 2+}, Cd{sup 2+} and Zn{sup 2+} cations from mixed solutions. The results show high efficiency and selective adsorption the Pb{sup 2+} and Zn{sup 2+} cations. The optimized adsorption parameters were further used in thermodynamic and kinetic studies of the adsorption processes. The Langmuir and Freundlich models were used to describe the processes. The pseudo-second order kinetics could well model all the processes, indicating a surface concentration of the adsorption sites with the same order of magnitude as the cation concentrations.

  11. Sustainable conversion of agro-wastes into useful adsorbents

    Science.gov (United States)

    Bello, Olugbenga Solomon; Owojuyigbe, Emmanuel Seun; Babatunde, Monsurat Abiodun; Folaranmi, Folasayo Eunice

    2017-11-01

    Preparation and characterization of raw and activated carbon derived from three different selected agricultural wastes: kola nut pod raw and activated (KNPR and KNPA), bean husk raw and activated (BHR and BHA) and coconut husk raw and activated (CHR and CHA) were investigated, respectively. Influences of carbonization and acid activation on the activated carbon were investigated using SEM, FTIR, EDX, pHpzc and Boehm titration techniques, respectively. Carbonization was done at 350 °C for 2 h followed by activation with 0.3 M H3PO4 (ortho-phosphoric acid). Results obtained from SEM, FTIR, and EDX revealed that, carbonization followed by acid activation had a significant influence on morphology and elemental composition of the samples. SEM showed well-developed pores on the surface of the precursors after acid treatment, FTIR spectra revealed reduction, broadening, disappearance or appearance of new peaks after acid activation. EDX results showed highest percentage of carbon by atom respectively in the order BHA > KNPA > CHA respectively. The pHpzc was found to be 5.32, 4.57 and 3.69 for KNPA, BHA and CHA, respectively. Boehm titration result compliments that of pHpzc, indicating that the surfaces of the prepared adsorbents are predominantly acidic. This study promotes a sustainable innovative use of agro-wastes in the production of cheap and readily available activated carbons, thereby ensuring more affordable water and effluent treatment adsorbents.

  12. Treatment of uranium mining and milling wastewater using biological adsorbents

    International Nuclear Information System (INIS)

    Tsezos, M.

    1983-01-01

    Selected samples of waste microbial biomass originating from various industrial fermentation processes and biological treatment plants have been screened for biosorbent properties in conjunction with uranium, thorium and radium in aqueous solutions. Biosorption isotherms were used for the evaluation of biosorptive uptake capacity of the biomass. The biomass was also compared to synthetic adsorbents such as activated carbon. Determined uranium, thorium and radium biosorption isotherms were independent of the initial solution concentrations. Solution pH affected uptake. Rhizopus arrhizus at pH 4 exhibited the highest uranium and thorium biosorptive uptake capacity in excess of 180 Mg/g. It removed about 2.5 and 3.3 times more uranium than the ion exchange resin and activated carbon tested. Penicillium chrysogenum adsorbed 50000 pCi/g radium at pH 7 and at an equilibrium radium concentration of 1000 pCi/L. The most effective biomass types studied exhibited removals in excess of 99% of the radium in solution

  13. Onset of Convection in Strongly Shaken Granular Matter

    NARCIS (Netherlands)

    Eshuis, Peter; Eshuis, P.G.; van der Meer, Roger M.; Alam, Meheboob; van Gerner, H.J.; van der Weele, J.P.; Lohse, Detlef

    2010-01-01

    Strongly vertically shaken granular matter can display a density inversion: A high-density cluster of beads is elevated by a dilute gaslike layer of fast beads underneath (“granular Leidenfrost effect”). For even stronger shaking the granular Leidenfrost state becomes unstable and granular

  14. The SNAP Strong Lens Survey

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, P.

    2005-01-03

    Basic considerations of lens detection and identification indicate that a wide field survey of the types planned for weak lensing and Type Ia SNe with SNAP are close to optimal for the optical detection of strong lenses. Such a ''piggy-back'' survey might be expected even pessimistically to provide a catalogue of a few thousand new strong lenses, with the numbers dominated by systems of faint blue galaxies lensed by foreground ellipticals. After sketching out our strategy for detecting and measuring these galaxy lenses using the SNAP images, we discuss some of the scientific applications of such a large sample of gravitational lenses: in particular we comment on the partition of information between lens structure, the source population properties and cosmology. Understanding this partitioning is key to assessing strong lens cosmography's value as a cosmological probe.

  15. Strong coupling phase in QED

    International Nuclear Information System (INIS)

    Aoki, Ken-ichi

    1988-01-01

    Existence of a strong coupling phase in QED has been suggested in solutions of the Schwinger-Dyson equation and in Monte Carlo simulation of lattice QED. In this article we recapitulate the previous arguments, and formulate the problem in the modern framework of the renormalization theory, Wilsonian renormalization. This scheme of renormalization gives the best understanding of the basic structure of a field theory especially when it has a multi-phase structure. We resolve some misleading arguments in the previous literature. Then we set up a strategy to attack the strong phase, if any. We describe a trial; a coupled Schwinger-Dyson equation. Possible picture of the strong coupling phase QED is presented. (author)

  16. Layering and Ordering in Electrochemical Double Layers

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yihua [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439, United States; Kawaguchi, Tomoya [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439, United States; Pierce, Michael S. [Rochester Institute of Technology, School of Physics and Astronomy, Rochester, New York 14623, United States; Komanicky, Vladimir [Faculty of Science, Safarik University, 041 54 Kosice, Slovakia; You, Hoydoo [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439, United States

    2018-02-26

    Electrochemical double layers (EDL) form at electrified interfaces. While Gouy-Chapman model describes moderately charged EDL, formation of Stern layers was predicted for highly charged EDL. Our results provide structural evidence for a Stern layer of cations, at potentials close to hydrogen evolution in alkali fluoride and chloride electrolytes. Layering was observed by x-ray crystal truncation rods and atomic-scale recoil responses of Pt(111) surface layers. Ordering in the layer is confirmed by glancing-incidence in-plane diffraction measurements.

  17. Development of Silver-exchanged Adsorbents for the Removal of Fission Iodine from Alkaline Dissolution

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Taewoon; Lee, Seung-Kon; Lee, Suseung; Lee, Jun Sig [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    Most of the iodine exists in the caustic dissolution as iodide form. KAERI is developing LEU-based fission 99 Mo production process which is connected to the new research reactor, which is being constructed in Kijang, Busan, Korea. In KAERI process, silver-exchanged adsorbent is used to adsorb iodide from the solution. Adsorbed iodide can be recovered and recycled for radiopharmaceuticals. In KAERI process, silver-exchanged adsorbent is used to adsorb iodide from the solution. Adsorbed iodide can be recovered and recycled for radiopharmaceuticals. Synthesis of silver-doped alumina is conducted in two ways. One is using the ascorbic acid as a reducing agent. However, this method is impossible to control.

  18. Attenuated total reflectance Fourier-transform infrared spectroscopy of carboxylic acids adsorbed onto mineral surfaces

    Science.gov (United States)

    Kubicki, J. D.; Schroeter, L. M.; Itoh, M. J.; Nguyen, B. N.; Apitz, S. E.

    1999-09-01

    A suite of naturally-occurring carboxylic acids (acetic, oxalic, citric, benzoic, salicylic and phthalic) and their corresponding sodium salts were adsorbed onto a set of common mineral substrates (quartz, albite, illite, kaolinite and montmorillonite) in batch slurry experiments. Solution pH's of approximately 3 and 6 were used to examine the effects of pH on sorption mechanisms. Attenuated total reflectance Fourier-transform infrared (ATR FTIR) spectroscopy was employed to obtain vibrational frequencies of the organic ligands on the mineral surfaces and in solution. UV/visible spectroscopy on supernatant solutions was also employed to confirm that adsorption from solution had taken place for benzoic, salicylic and phthalic acids. Molecular orbital calculations were used to model possible surface complexes and interpret the experimental spectra. In general, the tectosilicates, quartz and albite feldspar, did not chemisorb (i.e., strong, inner-sphere adsorption) the carboxylate anions in sufficient amounts to produce infrared spectra of the organics after rinsing in distilled water. The clays (illite, kaolinite and montmorillonite) each exhibited similar ATR FTIR spectra. However, the illite sample used in this study reacted to form strong surface and aqueous complexes with salicylic acid before being treated to remove free Fe-hydroxides. Chemisorption of carboxylic acids onto clays is shown to be limited without the presence of Fe-hydroxides within the clay matrix.

  19. Impact of Pore Size on Fenton Oxidation of Methyl Orange Adsorbed on Magnetic Carbon Materials: Trade-Off between Capacity and Regenerability.

    Science.gov (United States)

    Xiao, Ye; Hill, Josephine M

    2017-04-18

    The economic cleanup of wastewater continues to be an active area of research. In this study, the influence of pore size on regeneration by Fenton oxidation for carbon materials with adsorbed methyl orange (MO) was investigated. More specifically three carbon supports, with pore sizes ranging from mainly microporous to half microporous-half mesoporous to mainly mesoporous, were impregnated with γ-Fe 2 O 3 to make them magnetic and easy to separate from solution. The carbon samples were characterized before adsorption and after regeneration with hydrogen peroxide at 20 °C. In addition, adsorption kinetics and isotherms were collected, and the Weber-Morris intraparticle diffusion model and Freundlich isotherm model fit to the data. The adsorption capacity increased with increasing microporosity while the regeneration efficiency increased with increasing mesoporosity. Further experiments with varying regeneration and adsorption conditions suggested that the regeneration process may be kinetically limited. The MO adsorbed in the micropores was strongly adsorbed and difficult to remove unlike the MO adsorbed in the mesopores, which could be reacted under relatively mild conditions. Thus, there was a trade-off between adsorption capacity and regeneration.

  20. Toward an effective adsorbent for polar pollutants: Formaldehyde adsorption by activated carbon

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Kyung Jin [Department of Fine Chemical Engineering and Applied Chemistry, College of Engineering, Chungnam National University, 99 Daehak-ro (Sao Tome and Principe), Yuseong-gu, Daejeon 305-764 (Korea, Republic of); School of Chemical and Biological Engineering, College of Engineering, Seoul National University, Shinlimdong 56-1, Seoul 151-742 (Korea, Republic of); Miyawaki, Jin; Shiratori, Nanako [Institute for Materials Chemistry and Engineering, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan); Yoon, Seong-Ho, E-mail: yoon@cm.kyushu-u.ac.jp [Institute for Materials Chemistry and Engineering, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan); Jang, Jyongsik, E-mail: jsjang@plaza.snu.ac.kr [School of Chemical and Biological Engineering, College of Engineering, Seoul National University, Shinlimdong 56-1, Seoul 151-742 (Korea, Republic of)

    2013-09-15

    Highlights: • Activated carbon fiber with mild activation condition is useful as adsorbent for polar pollutants. • Diverse variations are investigated for developing an effective adsorbent. • Surface functional group is the most important factor for capacity as a adsorbent. • Surface functional groups on ACFs are investigated using micro-ATR FTIR. -- Abstract: Due to increasing concerns about environmental pollutants, the development of an effective adsorbent or sensitive sensor has been pursued in recent years. Diverse porous materials have been selected as promising candidates for detecting and removing harmful materials, but the most appropriate pore structure and surface functional groups, both important factors for effective adsorbency, have not yet been fully elucidated. In particular, there is limited information relating to the use of activated carbon materials for effective adsorbent of specific pollutants. Here, the pore structure and surface functionality of polyacrylonitrile-based activated carbon fibers were investigated to develop an efficient adsorbent for polar pollutants. The effect of pore structure and surface functional groups on removal capability was investigated. The activated carbons with higher nitrogen content show a great ability to absorb formaldehyde because of their increased affinity with polar pollutants. In particular, nitrogen functional groups that neighbor oxygen atoms play an important role in maximizing adsorption capability. However, because there is also a similar increase in water affinity in adsorbents with polar functional groups, there is a considerable decrease in adsorption ability under humid conditions because of preferential adsorption of water to adsorbents. Therefore, it can be concluded that pore structures, surface functional groups and the water affinity of any adsorbent should be considered together to develop an effective and practical adsorbent for polar pollutants. These studies can provide vital

  1. Effect of ultrasonic irradiation on the recovery of uranium from seawater with adsorbents

    International Nuclear Information System (INIS)

    Omichi, H.; Katakai, A.; Okamoto, J.

    1988-01-01

    Ultrasonic irradiation is reported to promote chelate formation between metal ions and polymeric ligands in solution. It is expected that the recovery of uranium from seawater with adsorbents is affected by ultrasonic irradiation because this process is also based on chelation between the ligands of the adsorbent and uranyl ion in seawater. In the present note, adsorption of uranium from seawater was carried out under ultrasonic irradiation with an amidoxime-group-containing polymeric adsorbent

  2. On the influence of adsorber performance on plant design for the extraction of uranium from seawater

    International Nuclear Information System (INIS)

    Koske, P.H.; Ohlrogge, K.

    1983-01-01

    Based on simple seawater and dissolved uranium balances the influence of specific adsorber parameters on size and design of production plants with fluidized adsorber beds for the extraction of uranium from seawater is discussed. Besides a critical review of two recently published plant designs in the USA and Japan experimentally determined adsorber data for a polyamidoxim (PAO) granulate are presented together with an evaluation of their influence on the key plant parameters. (orig.) [de

  3. Preparation of metal adsorbents from chitin/chitosan by radiation technology

    International Nuclear Information System (INIS)

    Nguyen Van Suc; Nguyen Quoc Hien; Ngo Quang Huy; Thai My Phe; Dao Van Hoang; Nguyen Van Hung

    2004-01-01

    The methods of preparation of metal adsorbents basing on chitin/chitosan were developed. That include the adsorbent from chitin grafted with acrylic acid by different irradiation doses; the clinging chitosan gel beads; the coagulable solution and the chitosan composite filter. The process of metal adsorption for each adsorbent was studied as adsorption kinetic, isothermal adsorption. The results have been applied for removal of some elements as Hg, Pb, Cd, U, Cu, ect. in the wastewater. (NHA)

  4. Toward an effective adsorbent for polar pollutants: Formaldehyde adsorption by activated carbon

    International Nuclear Information System (INIS)

    Lee, Kyung Jin; Miyawaki, Jin; Shiratori, Nanako; Yoon, Seong-Ho; Jang, Jyongsik

    2013-01-01

    Highlights: • Activated carbon fiber with mild activation condition is useful as adsorbent for polar pollutants. • Diverse variations are investigated for developing an effective adsorbent. • Surface functional group is the most important factor for capacity as a adsorbent. • Surface functional groups on ACFs are investigated using micro-ATR FTIR. -- Abstract: Due to increasing concerns about environmental pollutants, the development of an effective adsorbent or sensitive sensor has been pursued in recent years. Diverse porous materials have been selected as promising candidates for detecting and removing harmful materials, but the most appropriate pore structure and surface functional groups, both important factors for effective adsorbency, have not yet been fully elucidated. In particular, there is limited information relating to the use of activated carbon materials for effective adsorbent of specific pollutants. Here, the pore structure and surface functionality of polyacrylonitrile-based activated carbon fibers were investigated to develop an efficient adsorbent for polar pollutants. The effect of pore structure and surface functional groups on removal capability was investigated. The activated carbons with higher nitrogen content show a great ability to absorb formaldehyde because of their increased affinity with polar pollutants. In particular, nitrogen functional groups that neighbor oxygen atoms play an important role in maximizing adsorption capability. However, because there is also a similar increase in water affinity in adsorbents with polar functional groups, there is a considerable decrease in adsorption ability under humid conditions because of preferential adsorption of water to adsorbents. Therefore, it can be concluded that pore structures, surface functional groups and the water affinity of any adsorbent should be considered together to develop an effective and practical adsorbent for polar pollutants. These studies can provide vital

  5. Electrocatalytic Properties of BDD Anodes: Its Loosely Adsorbed Hydroxyl Radicals

    Directory of Open Access Journals (Sweden)

    Nicolaos Vatistas

    2012-01-01

    Full Text Available The high oxidative action of boron doped diamond (BDD anodes on the biorefractory organic compounds has been attributed to the low adsorption of the generated hydroxyl radicals on the BDD surface in respect to other anodic materials. In a previous paper, the effect of low adsorption of BBD has been studied by proposing a continuum approach to represent the adsorption layer. The oxidative action of the hydroxyl radicals is attributed to the values of their diffusivity into the adsorption and adjacent reactive layer as well as to the value of kinetic constant in both layers. In this paper, more details on both layers are reported in order to justify the proposed continuum approach as well as the assumptions concerning diffusivity and kinetic constant in both adsorption and reactive layers, where the oxidative action of hydroxyl radicals occurs.

  6. Preferential and selective degradation and removal of amelogenin adsorbed on hydroxyapatites by MMP20 and KLK4 in vitro

    Directory of Open Access Journals (Sweden)

    Li eZhu

    2014-07-01

    Full Text Available The hardest tooth enamel tissue develops from a soft layer of protein-rich matrix, predominated by amelogenin that is secreted by epithelial ameloblasts in the secretory stage of tooth enamel development. During enamel formation, a well-controlled progressive removal of matrix proteins by resident proteases, MMP20 and KLK4, will provide space for the apatite crystals to grow. To better understand the role of amelogenin degradation in enamel biomineralization, the present study was conducted to investigate how the adsorption of amelogenin to HAP crystals affects its degradation by enamel proteinases, MMP20 and KLK4. Equal quantities of amelogenins confirmed by protein assays before digestions, either adsorbed to HAP or in solution, were incubated with MMP20 or KLK4. The digested samples collected at different time points were analyzed by spectrophotometry, SDS-PAGE, HPLC and LC/MALDI MS/MS. We found that majority of amelogenin adsorbed on HAP was released into the surrounding solution by enzymatic processing (88% for MMP20 and 98% for KLK4. The results show that as compared with amelogenin in solution, the HAP-bound amelogenin was hydrolyzed by both MMP20 and KLK4 at significantly higher rates. Using LC/MALDI MS-MS, more accessible cleavage sites and hydrolytic fragments from MMP20/KLK4 digestion were identified for the amelogenin adsorbed on HAP crystals as compared to the amelogenin in solution. These results suggest that the adsorption of amelogenin to HAP results in their preferential and selective degradation and removal from HAP by MMP20 and KLK4 in vitro. Based on these findings, a new degradation model related to enamel crystal growth is proposed.

  7. Synthesis of hexagonal mesoporous MgAl LDH nanoplatelets adsorbent for the effective adsorption of Brilliant Yellow.

    Science.gov (United States)

    Pourfaraj, Reza; Fatemi, Seyed Jamilaldin; Kazemi, Sayed Yahya; Biparva, Pourya

    2017-12-15

    Hexagonal mesoporous MgAl layered double hydroxide (LDH) was synthesized through a simple hydrothermal method and was employed without calcination as adsorbent in the removal of the direct anionic azo dye, Brilliant Yellow (BY). The adsorbent was characterized by XRD, FT-IR, SEM and BET surface area. Hexagonal platelets of MgAl LDH were fabricated with nanometric building blocks. Batch experiments were carried out for study effects of contact time, amount of adsorbent, solution pH and solution temperature on the removal efficiency of BY. The adsorption of BY onto the MgAl LDH was pH dependent and the highest value of adsorption capacity was observed at pH=6. The equilibrium adsorption data were obtained using the Langmuir, Freundlich and Temkin isotherms. The results indicated that the experimental adsorption data were fitted to Langmuir and Freundlich models. The maximum adsorption capacity of BY onto the MgAl LDH was found to be 115mg/g. The kinetic data of adsorption were evaluated by pseudo-first order and pseudo-second order, which described well by pseudo-second order model. The negative values of ΔG° at all temperature indicated that the adsorption process was spontaneous. The values of ΔH° and ΔS° were calculated 19.3kJ/mol and 80.5J/mol·K, respectively. The positive value of ΔH° shows that the adsorption was endothermic, while positive ΔS° value reflects increased disorder at the solid-solution interface during the adsorption. Copyright © 2017 Elsevier Inc. All rights reserved.

  8. Self-assembled patterns from evaporating layered fluids

    International Nuclear Information System (INIS)

    Govor, L V; Parisi, J; Bauer, G H; Reiter, G

    2009-01-01

    We studied the formation of tree-like patterns of polymer aggregates and rings of nanoparticles during evaporation from a fluid film. We utilize phase separation between two immiscible fluids to generate a double-layer film which dries up in a sequential manner. Both fluid layers may contain a solute, polymer aggregates or nanoparticles. During evaporation of the top layer, instabilities may occur and direct a self-assembly process of the solute which may be further affected by an instability of the bottom layer at a later stage. We present two cases where, after evaporation of the top fluid layer, the solute was adsorbed on the surface of the bottom fluid layer. In comparison to dewetting of a single fluid layer on a solid substrate, the advantage of our double-layer approach lies in the deposition of the solute on the surface of the bottom fluid layer. The relatively high mobility of the solute on such a fluid surface favors the formation of ordered patterns, driven by an instability of the bottom layer.

  9. Strong Decomposition of Random Variables

    DEFF Research Database (Denmark)

    Hoffmann-Jørgensen, Jørgen; Kagan, Abram M.; Pitt, Loren D.

    2007-01-01

    A random variable X is stongly decomposable if X=Y+Z where Y=Φ(X) and Z=X-Φ(X) are independent non-degenerated random variables (called the components). It is shown that at least one of the components is singular, and we derive a necessary and sufficient condition for strong decomposability...

  10. Strong interaction at finite temperature

    Indian Academy of Sciences (India)

    Abstract. We review two methods discussed in the literature to determine the effective parameters of strongly interacting particles as they move through a heat bath. The first one is the general method of chiral perturbation theory, which may be readily applied to this problem. The other is the method of thermal QCD sum rules ...

  11. Strong-strong beam-beam simulation on parallel computer

    Energy Technology Data Exchange (ETDEWEB)

    Qiang, Ji

    2004-08-02

    The beam-beam interaction puts a strong limit on the luminosity of the high energy storage ring colliders. At the interaction points, the electromagnetic fields generated by one beam focus or defocus the opposite beam. This can cause beam blowup and a reduction of luminosity. An accurate simulation of the beam-beam interaction is needed to help optimize the luminosity in high energy colliders.

  12. Strong-strong beam-beam simulation on parallel computer

    International Nuclear Information System (INIS)

    Qiang, Ji

    2004-01-01

    The beam-beam interaction puts a strong limit on the luminosity of the high energy storage ring colliders. At the interaction points, the electromagnetic fields generated by one beam focus or defocus the opposite beam. This can cause beam blowup and a reduction of luminosity. An accurate simulation of the beam-beam interaction is needed to help optimize the luminosity in high energy colliders

  13. Synthesis of adsorbent from Tamarix hispida and modified by lanthanum metal for fluoride ions removal from wastewater: Adsorbent characteristics and real wastewater treatment data

    Directory of Open Access Journals (Sweden)

    Nasim Habibi

    2017-08-01

    Full Text Available This data article describes a facile method for production of an adsorbent from Tamarix hispida wasted wood and modified by lanthanum metal for fluoride ions removal from wastewater. The main characteristics of the adsorbent consist of BET surface area, functional groups, and elemental analysis is presented. The data for attenuating the pollutants from a real wastewater treatment which was provided from a glass factory is also represented. More than 90% of fluoride content of the real wastewater was treated by the adsorbent. Generally, these data would be informative for extend research aim to industrial wastewater treatment and those who work in the wastewater treatment plants.

  14. Investigations into Alternative Desorption Agents for Amidoxime-Based Polymeric Uranium Adsorbents

    Energy Technology Data Exchange (ETDEWEB)

    Gill, Gary A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kuo, Li-Jung [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Strivens, Jonathan E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wood, Jordana R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wai, Chien [LCW Supercritical Technologies, Inc., Seattle, WA (United States); Pan, Horng-Bin [Univ. of Idaho, Moscow, ID (United States)

    2015-06-01

    Amidoxime-based polymeric braid adsorbents that can extract uranium (U) from seawater are being developed to provide a sustainable supply of fuel for nuclear reactors. A critical step in the development of the technology is to develop elution procedures to selectively remove U from the adsorbents and to do so in a manner that allows the adsorbent material to be reused. This study investigates use of high concentrations of bicarbonate along with targeted chelating agents as an alternative means to the mild acid elution procedures currently in use for selectively eluting uranium from amidoxime-based polymeric adsorbents.

  15. Detection of adsorbed explosive molecules using thermal response of suspended microfabricated bridges

    DEFF Research Database (Denmark)

    Yi, Dechang; Greve, Anders; Hales, Jan Harry

    2008-01-01

    Here we present a thermophysical technique that is capable of differentiating vapor phase adsorbed explosives from nonexplosives and is additionally capable of differentiating individual species of common explosive vapors. This technique utilizes pairs of suspended microfabricated silicon bridges...... that can be heated in a controlled fashion. The differential thermal response of the bridges with and without adsorbed explosive vapor shows unique and reproducible characteristics depending on the nature of the adsorbed explosives. The tunable heating rate method described here is capable of providing...... unique signals for subnanogram quantities of adsorbed explosives within 50 ms. (C) 2008 American Institute of Physics....

  16. Preparation and characterization of a novel electrospun ammonium molybdophosphate/polyacrylonitrile nanofiber adsorbent for cesium removal

    International Nuclear Information System (INIS)

    Amin Tabatabaeefar; Mohammad Ali Moosavian; Ali Reza Keshtkar

    2015-01-01

    Adsorption of Cs + ion from aqueous solution onto a novel electrospun ammonium molybdophosphate/polyacrylonitrile nanofiber adsorbent with variation in AMP content, adsorbent concentration, pH, contact time, initial concentration and temperature was studied. The physicochemical characterization was performed by FTIR, XRD, BET and SEM analyses. Langmuir, Freundlich and Dubinin-Radushkevich models were used for analysis of equilibrium data. Kinetic results showed that the experimental data best fitted the pseudo-second-order kinetic model. The adsorption affinity of metal ions onto adsorbent was in order of Cs + > Co 2+ > Mg 2+ > Ca 2+ > Sr 2+ . The adsorbent could be easily regenerated after five cycles of adsorption-desorption. (author)

  17. Uranium recovery from seawater: development of fiber adsorbents prepared via atom-transfer radical polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Tomonori [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Chemical Sciences Division; Brown, Suree [Univ. of Tennessee, Knoxville, TN (United States). Dept. of Chemistry; Chatterjee, Sabornie [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Chemical Sciences Division; Kim, Jungseung [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Energy and Transportation Science Division; Tsouris, Costas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Energy and Transportation Science Division; Mayes, Richard T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Chemical Sciences Division; Kuo, Li-Jung [Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Marine Science Lab.; Gill, Gary [Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Marine Science Lab.; Oyola, Yatsandra [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Chemical Sciences Division; Janke, Christopher J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division; Dai, Sheng [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Chemical Sciences Division; Univ. of Tennessee, Knoxville, TN (United States). Marine Sciences Lab.

    2014-08-04

    We developed a novel adsorbent preparation method using atom-transfer radical polymerization (ATRP) combined with radiation-induced graft polymerization (RIGP) in order to synthesize an adsorbent for uranium recovery from seawater. Furthermore, the ATRP method allowed a much higher degree of grafting on the adsorbent fibers (595 2818%) than that allowed by RIGP alone. The adsorbents were prepared with varied composition of amidoxime groups and hydrophilic acrylate groups. The successful preparation revealed that both ligand density and hydrophilicity were critical for optimal performance of the adsorbents. Adsorbents synthesized in this study showed a relatively high performance (141 179 mg/g at 49 62 % adsorption) in laboratory screening tests using a uranium concentration of ~6 ppm. This performance is much higher than that of known commercial adsorbents. However, actual seawater experiment showed impeded performance compared to the recently reported high-surface-area-fiber adsorbents, due to slow adsorption kinetics. The impeded performance motivated an investigation of the effect of hydrophilic block addition on the graft chain terminus. The addition of hydrophilic block on the graft chain terminus nearly doubled the uranium adsorption capacity in seawater, from 1.56 mg/g to 3.02 mg/g. Our investigation revealed the importance of polymer chain conformation, in addition to ligand and hydrophilic group ratio, for advanced adsorbent synthesis for uranium recovery from seawater.

  18. Biodegradable metal adsorbent synthesized by graft polymerization onto nonwoven cotton fabric

    International Nuclear Information System (INIS)

    Sekine, Ayako; Seko, Noriaki; Tamada, Masao; Suzuki, Yoshio

    2010-01-01

    A fibrous adsorbent for Hg ions was synthesized by radiation-induced emulsion graft polymerization of glycidyl methacrylate (GMA) onto a nonwoven cotton fabric and subsequent chemical modification. The optimal pre-irradiation dose for initiation of the graft polymerization of GMA, which minimized the effects of radiation damage on the mechanical strength of the nonwoven cotton fabric, was found to be 10 kGy. The GMA-grafted nonwoven cotton fabric was subsequently modified with ethylenediamine (EDA) or diethylenetriamine (DETA) to obtain a Hg adsorbent. The resulting amine-type adsorbents were evaluated for batch and continuous adsorption of Hg. In batch adsorption, the distribution coefficients of Hg reached 1.9x10 5 and 1.0x10 5 for EDA- and DETA-type adsorbents, respectively. A column packed with EDA-type adsorbent removed Hg from 1.8 ppm Hg solution at a space velocity of 100 h -1 , which corresponds to 16,000 times the volume of the packed adsorbent. The adsorbed Hg on the EDA-type adsorbent could be completely eluted by 1 M HCl solution. A microbial oxidative degradation test revealed that the EDA-type adsorbent is biodegradable.

  19. Chemical and structural characterization of copper adsorbed on mosses (Bryophyta)

    Energy Technology Data Exchange (ETDEWEB)

    González, Aridane G., E-mail: aridaneglez@gmail.com [GET (Géosciences Environnement Toulouse) UMR 5563CNRS, 14 Avenue Edouard Belin, F-31400 Toulouse (France); Jimenez-Villacorta, Felix [Instituto de Ciencia de Materiales Madrid, CSIC, Cantoblanco, E-28049 Madrid (Spain); Beike, Anna K. [Plant Biotechnology, Faculty of Biology, University of Freiburg, Schaenzlestrasse 1, 79104 Freiburg (Germany); State Museum of Natural History Stuttgart, Rosenstein 1, 70191 Stuttgart (Germany); Reski, Ralf [Plant Biotechnology, Faculty of Biology, University of Freiburg, Schaenzlestrasse 1, 79104 Freiburg (Germany); BIOSS—Centre for Biological Signalling Studies, 79104 Freiburg (Germany); FRIAS—Freiburg Institute for Advanced Studies, 79104 Freiburg (Germany); Adamo, Paola [Department of Agricultural Sciences, University of Naples Federico II, Via Università 100, 80055 Naples (Italy); Pokrovsky, Oleg S. [GET (Géosciences Environnement Toulouse) UMR 5563CNRS, 14 Avenue Edouard Belin, F-31400 Toulouse (France); BIO-GEO-CLIM Laboratory, Tomsk State University, Tomsk (Russian Federation); Institute of Ecological Problems of the North, Russian Academy of Science, Arkhangelsk (Russian Federation)

    2016-05-05

    Highlights: • Cu{sup 2+} was adsorbed on four mosses used in moss-bag pollution monitoring technique. • Thermodynamic approach was used to model Cu speciation based on XAS results. • All studied mosses have ∼4.5 O/N atoms at ∼1.95 Å around Cu likely in a pseudo-square geometry. • Cu(II)-carboxylates and Cu(II)-phosphoryls are the main moss surface binding groups. • Moss growing in batch reactor yielded ∼20% of Cu(I) in the form of Cu–S(CN) complexes. - Abstract: The adsorption of copper on passive biomonitors (devitalized mosses Hypnum sp., Sphagnum denticulatum, Pseudoscleropodium purum and Brachythecium rutabulum) was studied under different experimental conditions such as a function of pH and Cu concentration in solution. Cu assimilation by living Physcomitrella patents was also investigated. Molecular structure of surface adsorbed and incorporated Cu was studied by X-ray Absorption Spectroscopy (XAS). Devitalized mosses exhibited the universal adsorption pattern of Cu as a function of pH, with a total binding sites number 0.05–0.06 mmolg{sub dry}{sup −1} and a maximal adsorption capacity of 0.93–1.25 mmolg{sub dry}{sup −1} for these devitalized species. The Extended X-ray Absorption Fine Structure (EXAFS) fit of the first neighbor demonstrated that for all studied mosses there are ∼4.5 O/N atoms around Cu at ∼1.95 Å likely in a pseudo-square geometry. The X-ray Absorption Near Edge Structure (XANES) analysis demonstrated that Cu(II)-cellulose (representing carboxylate groups) and Cu(II)-phosphate are the main moss surface binding moieties, and the percentage of these sites varies as a function of solution pH. P. patens exposed during one month to Cu{sup 2+} yielded ∼20% of Cu(I) in the form of Cu–S(CN) complexes, suggesting metabolically-controlled reduction of adsorbed and assimilated Cu{sup 2+}.

  20. Strong Motion Seismograph Based On MEMS Accelerometer

    Science.gov (United States)

    Teng, Y.; Hu, X.

    2013-12-01

    The MEMS strong motion seismograph we developed used the modularization method to design its software and hardware.It can fit various needs in different application situation.The hardware of the instrument is composed of a MEMS accelerometer,a control processor system,a data-storage system,a wired real-time data transmission system by IP network,a wireless data transmission module by 3G broadband,a GPS calibration module and power supply system with a large-volumn lithium battery in it. Among it,the seismograph's sensor adopted a three-axis with 14-bit high resolution and digital output MEMS accelerometer.Its noise level just reach about 99μg/√Hz and ×2g to ×8g dynamically selectable full-scale.Its output data rates from 1.56Hz to 800Hz. Its maximum current consumption is merely 165μA,and the device is so small that it is available in a 3mm×3mm×1mm QFN package. Furthermore,there is access to both low pass filtered data as well as high pass filtered data,which minimizes the data analysis required for earthquake signal detection. So,the data post-processing can be simplified. Controlling process system adopts a 32-bit low power consumption embedded ARM9 processor-S3C2440 and is based on the Linux operation system.The processor's operating clock at 400MHz.The controlling system's main memory is a 64MB SDRAM with a 256MB flash-memory.Besides,an external high-capacity SD card data memory can be easily added.So the system can meet the requirements for data acquisition,data processing,data transmission,data storage,and so on. Both wired and wireless network can satisfy remote real-time monitoring, data transmission,system maintenance,status monitoring or updating software.Linux was embedded and multi-layer designed conception was used.The code, including sensor hardware driver,the data acquisition,earthquake setting out and so on,was written on medium layer.The hardware driver consist of IIC-Bus interface driver, IO driver and asynchronous notification driver. The

  1. Biochemical composition of the superficial layer of articular cartilage.

    Science.gov (United States)

    Crockett, R; Grubelnik, A; Roos, S; Dora, C; Born, W; Troxler, H

    2007-09-15

    To gain more information on the mechanism of lubrication in articular joints, the superficial layer of bovine articular cartilage was mechanically removed in a sheet of ice that formed on freezing the cartilage. Freeze-dried samples contained low concentrations of chondroitin sulphate and protein. Analysis of the protein by SDS PAGE showed that the composition of the sample was comparable to that of synovial fluid (SF). Attenuated total reflection infrared (ATR-IR) spectroscopy of the dried residue indicated that the sample contained mostly hyaluronan. Moreover, ATR-IR spectroscopy of the upper layer of the superficial layer, adsorbed onto silicon, showed the presence of phospholipids. A gel could be formed by mixing hyaluronan and phosphatidylcholine in water with mechanical properties similar to those of the superficial layer on cartilage. Much like the superficial layer of natural cartilage, the surface of this gel became hydrophobic on drying out. Thus, it is proposed that the superficial layer forms from hyaluronan and phospholipids, which associate by hydrophobic interactions between the alkyl chains of the phospholipids and the hydrophobic faces of the disaccharide units in hyaluronan. This layer is permeable to material from the SF and the cartilage, as shown by the presence of SF proteins and chondroitin sulphate. As the cartilage dries out after removal from the joint, the phospholipids migrate towards the surface of the superficial layer to reduce the surface tension. It is also proposed that the highly efficient lubrication in articular joints can, at least in part, be attributed to the ability of the superficial layer to adsorb and hold water on the cartilage surface, thus creating a highly viscous boundary protection. Copyright 2007 Wiley Periodicals, Inc.

  2. PREFACE: Strongly correlated electron systems Strongly correlated electron systems

    Science.gov (United States)

    Saxena, Siddharth S.; Littlewood, P. B.

    2012-07-01

    This special section is dedicated to the Strongly Correlated Electron Systems Conference (SCES) 2011, which was held from 29 August-3 September 2011, in Cambridge, UK. SCES'2011 is dedicated to 100 years of superconductivity and covers a range of topics in the area of strongly correlated systems. The correlated electronic and magnetic materials featured include f-electron based heavy fermion intermetallics and d-electron based transition metal compounds. The selected papers derived from invited presentations seek to deepen our understanding of the rich physical phenomena that arise from correlation effects. The focus is on quantum phase transitions, non-Fermi liquid phenomena, quantum magnetism, unconventional superconductivity and metal-insulator transitions. Both experimental and theoretical work is presented. Based on fundamental advances in the understanding of electronic materials, much of 20th century materials physics was driven by miniaturisation and integration in the electronics industry to the current generation of nanometre scale devices. The achievements of this industry have brought unprecedented advances to society and well-being, and no doubt there is much further to go—note that this progress is founded on investments and studies in the fundamentals of condensed matter physics from more than 50 years ago. Nevertheless, the defining challenges for the 21st century will lie in the discovery in science, and deployment through engineering, of technologies that can deliver the scale needed to have an impact on the sustainability agenda. Thus the big developments in nanotechnology may lie not in the pursuit of yet smaller transistors, but in the design of new structures that can revolutionise the performance of solar cells, batteries, fuel cells, light-weight structural materials, refrigeration, water purification, etc. The science presented in the papers of this special section also highlights the underlying interest in energy-dense materials, which

  3. Photoenhanced atomic layer epitaxy. Hikari reiki genshiso epitaxy

    Energy Technology Data Exchange (ETDEWEB)

    Mashita, M.; Kawakyu, Y. (Toshiba corp., Tokyo (Japan))

    1991-10-01

    The growth temperature range was greatly expanded of atomic layer epitaxy (ALE) expected as the growth process of ultra-thin stacks. Ga layers and As layers were formed one after the other on a GaAs substrate in the atmosphere of trimethylgallium (TMG) or AsH{sub 2} supplied alternately, by KrF excimer laser irradiation normal to the substrate. As a result, the growth temperature range was 460-540{degree}C nearly 10 times that of 500 {plus minus} several degrees centigrade in conventional thermal growth method. Based on the experimental result where light absorption of source molecules adsorbed on a substrate surface was larger than that under gaseous phase condition, new adsorbed layer enhancement model was proposed to explain above irradiation effect verifying it by experiments. As this photoenhancement technique is applied to other materials, possible fabrication of new crystal structures as a super lattice with ultra-thin stacks of single atomic layers is expected because of a larger freedom in material combination for hetero-ALE. 11 refs., 7 figs.

  4. Structure and dynamics of confined flexible and unentangled polymer melts in highly adsorbing cylindrical pores

    International Nuclear Information System (INIS)

    Carrillo, Jan-Michael Y.; Sumpter, Bobby G.

    2014-01-01

    Coarse-grained molecular dynamics simulations are used to probe the dynamic phenomena of polymer melts confined in nanopores. The simulation results show excellent agreement in the values obtained for the normalized coherent single chain dynamic structure factor, (S(Q,Δt))/(S(Q,0)) . In the bulk configuration, both simulations and experiments confirm that the polymer chains follow Rouse dynamics. However, under confinement, the Rouse modes are suppressed. The mean-square radius of gyration 〈R g 2 〉 and the average relative shape anisotropy 〈κ 2 〉 of the conformation of the polymer chains indicate a pancake-like conformation near the surface and a bulk-like conformation near the center of the confining cylinder. This was confirmed by direct visualization of the polymer chains. Despite the presence of these different conformations, the average form factor of the confined chains still follows the Debye function which describes linear ideal chains, which is in agreement with small angle neutron scattering experiments (SANS). The experimentally inaccessible mean-square displacement (MSD) of the confined monomers, calculated as a function of radial distance from the pore surface, was obtained in the simulations. The simulations show a gradual increase of the MSD from the adsorbed, but mobile layer, to that similar to the bulk far away from the surface

  5. A natural adsorbent for natural gas industry; Um adsorvente nacional para a industria do gas natural

    Energy Technology Data Exchange (ETDEWEB)

    Cachina, G.H.A.B.; Silveira, V.R.; Melo, D.M.A. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Balthar, A.R.; Oliveira, V.M.; Bayer, M.M. [CTGAS - Centro de Tecnologias do Gas, Natal, RN (Brazil); Barbosa, C.M.M. [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil)

    2004-07-01

    One the natural pollutants in the natural gas considered critical in reference to the corrosion is the H{sub 2}S. Its presence depends on the origin, as well as the own process used in the gas treatment, it can bring problems to the pipes and the final applications of natural gas (NG). The National Petroleum Agency (ANP) in its entrance number 104/02, establishes that the quantity of H{sub 2}S in NG, of national or imported origin, commercialized at the country can only be at the most 10 - 15 mg/m{sup 3}. In the Natural Gas Processing Unit (UPGN) different methods are used for the removal of H{sub 2}S, the absorption process (e.g. with aminas, Sulfinol{sup R} process) or for adsorption in tower filled with activated coal, zeolites and Sulfatreat{sup R}. In this work, the adsorbent material used is the mineral clay Paligorsquita. That class of clay minerals characterized by pores and a crystalline structure containing Tetrahedral layers linked by chains of longitudinal secondary lines. The typical unitary cell is formed basically by moisturized oxides of aluminum, Sicilian and magnesium of (Mg, Al)5SiO2O(OH)2(H20)4.4H20, with Mg specially located in octahedral sites. (author)

  6. Adsorbed Eutectic GaIn Structures on a Neoprene Foam for Stretchable MRI Coils.

    Science.gov (United States)

    Varga, Matija; Mehmann, Andreas; Marjanovic, Josip; Reber, Jonas; Vogt, Christian; Pruessmann, Klaas Paul; Tröster, Gerhard

    2017-11-01

    Stretchable conductors based on eutectic gallium-indium (eGaIn) alloy are patterned on a polychloroprene substrate (neoprene foam) using stencil printing. By tuning the amount of eGaIn on the neoprene substrate, different strain-sensitivity of electrical resistance is achieved. Conductors with a layer of eGaIn, which adsorbs to the walls of 60-100 µm wide neoprene cells, change their electrical resistance for 5% at 100% strain. When the amount of eGaIn is increased, the cells are filled with eGaIn and the strain-sensitivity of the electrical resistance rises to 300% at 100% strain. The developed conductors are patterned as stretchable on-body coils for receiving magnetic signals in a clinical magnetic resonance imaging setup. First images with a stretchable coil are acquired on an orange and compared to the images that are recorded using a rigid copper coil of the same size. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Modeling the interaction of nanoparticles with mineral surfaces: adsorbed C60 on pyrophyllite.

    Science.gov (United States)

    Zhu, Runliang; Molinari, Marco; Shapley, Thomas V; Parker, Stephen C

    2013-08-01

    We have applied DFT and molecular modeling to investigate the interaction between carbon-based nanoparticles (CNPs) and geosorbents using the adsorption of buckminsterfullerene (C60) on pyrophyllite and comparing it to the aggregation of C60 molecules. The approach is transferable and can be readily applied to more complex CNP-clay systems. We predict that C60 molecules adsorb preferably on the mineral surface and that the most stable adsorption site is the ditrigonal cavity of the surface. The free energy of adsorption on pyrophyllite was calculated to be more favorable than aggregation both in a vacuum (-0.47 vs -0.41 eV) and in water (-0.25 vs -0.19 eV). In aqueous environments, there are energy barriers as the C60 molecule approaches either a surface or another C60 molecule, and these occur upon disruption of the hydration layers that surround each component. There are also free energy minima that correspond to outer-sphere and more favorable inner-sphere complexes. We expect this adsorptive behavior to be a general feature of CNP-clay systems, and as clays are ubiquitous in the environment, it will offer an inexpensive remediative method to prevent the widespread impact of molecular C60 and CNPs.

  8. Application of Henry's Law for Binding Energies of Adsorbed Hydrogen

    Science.gov (United States)

    Gillespie, Andrew; Dohnke, Elmar; Stalla, David; Sweany, Mark; Pfeifer, Peter

    2015-03-01

    The method of isosteres is the simplest method used to calculate the differential enthalpy of adsorption. However, it is incredibly sensitive to the choice of model and respective fitting parameters. For a set of isotherms measured on a specific sample, most models converge upon a similar value at high coverage, but are inconsistent in the low pressure regime. In this talk, we investigate the application of various models for localized and mobile adsorption at low pressures in order to obtain binding energy of hydrogen to the adsorbent surface. Henry's Law analysis of the Langmuir Model of adsorption yield binding energies in excellent agreement with those obtained from the Clausius Clapeyron relation. Work supported by DOE-EERE, Award No. DE-FG36-08GO18142.

  9. Hydrophobic CuO Nanosheets Functionalized with Organic Adsorbates.

    Science.gov (United States)

    He, Yulian; Fishman, Zachary S; Yang, Ke R; Ortiz, Brandon; Liu, Chaolun; Goldsamt, Julia; Batista, Victor S; Pfefferle, Lisa D

    2018-02-07

    A new class of hydrophobic CuO nanosheets is introduced by functionalization of the cupric oxide surface with p-xylene, toluene, hexane, methylcyclohexane, and chlorobenzene. The resulting nanosheets exhibit a wide range of contact angles from 146° (p-xylene) to 27° (chlorobenzene) due to significant changes in surface composition induced by functionalization, as revealed by XPS and ATR-FTIR spectroscopies and computational modeling. Aromatic adsorbates are stable even up to 250-350 °C since they covalently bind to the surface as alkoxides, upon reaction with the surface as shown by DFT calculations and FTIR and 1 H NMR spectroscopy. The resulting hydrophobicity correlates with H 2 temperature-programmed reduction (H 2 -TPR) stability, which therefore provides a practical gauge of hydrophobicity.

  10. On the adsorbed mass of polymers on surfaces (NOTE

    Directory of Open Access Journals (Sweden)

    GEORGIOS K. STRATOURAS

    2001-06-01

    Full Text Available It is shown that for ideal polymers interacting with a surface via the pseudopotential of a delta function, the number of contacts between the monomer units and the surface as a function of concentration cb is a dependence of the form acb/(1–bcb. The architecture of the polymer, the degree of polymerization, the interaction energy between a monomer unit and the surface, the area of the surface and the monomer length are embodied in the parameters a and b. The above dependence of the adsorbed mass of a polymer on the concentration is confirmed by the experimental results of Takahashi and his collaborators. For linear polystyrene of molecular weight 134×105,interacting with a chrome plate, the parameters a and b are, respectively, about equal to (89938/273 ×10-6 m and (–19300/273 m3 kg-1.

  11. Experimental and Numerical Study of Effect of Thermal Management on Storage Capacity of the Adsorbed Natural Gas Vessel

    KAUST Repository

    Ybyraiymkul, Doskhan

    2017-07-08

    One of the main challenges in the adsorbed natural gas (ANG) storage system is the thermal effect of adsorption, which significantly lowers storage capacity. These challenges can be solved by efficient thermal management system. In this paper, influence of thermal management on storage capacity of the ANG vessel was studied experimentally and numerically. 3D numerical model was considered in order to understand heat transfer phenomena and analyze influence of thermal control comprehensively. In addition, a detailed 2D axisymmetric unit cell model of adsorbent layer with heat exchanger was developed, followed by optimization of heat exchanging device design to minimize volume occupied by fins and tubes. Heat transfer, mass transfer and adsorption kinetics, which occur in ANG vessel during charging process, are accounted for in models. Nelder-Mead method is implemented to obtain the geometrical parameters, which lead to the optimal characteristics of heat exchange. A new optimized configuration of ANG vessel was developed with compact heat exchanger. Results show that storage capacity of the ANG vessel increased significantly due to lowering of heat exchanger volume for 3 times from 13.5% to 4.3% and effective temperature control.

  12. Artificial neural network modeling in competitive adsorption of phenol and resorcinol from water environment using some carbonaceous adsorbents.

    Science.gov (United States)

    Aghav, R M; Kumar, Sunil; Mukherjee, S N

    2011-04-15

    This paper illustrates the application of artificial neural network (ANN) for prediction of performances in competitive adsorption of phenol and resorcinol from aqueous solution by conventional and low cost carbonaceous adsorbent materials, such as activated carbon (AC), wood charcoal (WC) and rice husk ash (RHA). The three layer's feed forward neural network with back propagation algorithm in MATLAB environment was used for estimation of removal efficiencies of phenol and resorcinol in bi-solute water environment based on 29 sets of laboratory batch study results. The input parameters used for training of the neural network include amount of adsorbent (g/L), initial concentrations of phenol (mg/L) and resorcinol (mg/L), contact time (h), and pH. The removal efficiencies of phenol and resorcinol were considered as an output of the neural network. The performances of the developed ANN models were also measured using statistical parameters, such as mean error, mean square error, root mean square error, and linear regression. The comparison of the removal efficiencies of pollutants using ANN model and experimental results showed that ANN modeling in competitive adsorption of phenolic compounds reasonably corroborated with the experimental results. Copyright © 2011 Elsevier B.V. All rights reserved.

  13. Sensitivity of photoelectron diffraction to conformational changes of adsorbed molecules: Tetra-tert-butyl-azobenzene/Au(111

    Directory of Open Access Journals (Sweden)

    A. Schuler

    2017-01-01

    Full Text Available Electron diffraction is a standard tool to investigate the atomic structure of surfaces, interfaces, and adsorbate systems. In particular, photoelectron diffraction is a promising candidate for real-time studies of structural dynamics combining the ultimate time resolution of optical pulses and the high scattering cross-sections for electrons. In view of future time-resolved experiments from molecular layers, we studied the sensitivity of photoelectron diffraction to conformational changes of only a small fraction of molecules in a monolayer adsorbed on a metallic substrate. 3,3′,5,5′-tetra-tert-butyl-azobenzene served as test case. This molecule can be switched between two isomers, trans and cis, by absorption of ultraviolet light. X-ray photoelectron diffraction patterns were recorded from tetra-tert-butyl-azobenzene/Au(111 in thermal equilibrium at room temperature and compared to patterns taken in the photostationary state obtained by exposing the surface to radiation from a high-intensity helium discharge lamp. Difference patterns were simulated by means of multiple-scattering calculations, which allowed us to determine the fraction of molecules that underwent isomerization.

  14. Chemical reduction of nitrate by zerovalent iron nanoparticles adsorbed radiation-grafted copolymer matrix

    Directory of Open Access Journals (Sweden)

    Ratnayake Sanduni Y.

    2017-12-01

    Full Text Available This research specifically focused on the development of a novel methodology to reduce excess nitrate in drinking water utilizing zerovalent iron nanoparticles (nZVI-stabilized radiation-grafted copolymer matrix. nZVI was synthesized by borohydrate reduction of FeCl3 and stabilized on acrylic acid (AAc-grafted non-woven polyethylene/polypropylene (NWPE/PP-g-AAc copolymer matrix, which was grafted using gamma radiation. The use of nZVI for environmental applications is challenging because of the formation of an oxide layer rapidly in the presence of oxygen. Therefore, radiation-grafted NWPE/PP synthetic fabric was used as the functional carrier to anchor nZVI and enhance its spreading and stability. The chemical reduction of nitrate by nZVI-adsorbed NWPE/PP-g-AAc (nZVI-Ads-NWP fabric was examined in batch experiments at different pH values. At low pH values, the protective layers on nZVI particles can be readily dissolved, exposing the pure iron particles for efficient chemical reduction of nitrate. After about 24 h, at pH 3, almost 96% of nitrate was degraded, suggesting that this reduction process is an acid-driven, surface-mediated process. The nZVI-water interface has been characterized by the 1-pK Basic Stern Model (BSM. An Eley-Rideal like mechanism well described the nitrate reduction kinetics. In accordance with green technology, the newly synthesized nZVI-Ads-NWP has great potential for improving nitrate reduction processes required for the drinking water industry.

  15. Band mapping of surface states vs. adsorbate coverage

    International Nuclear Information System (INIS)

    Rotenberg, E.; Kevan, S.D.; Denlinger, J.D.; Chung, Jin-Wook

    1997-01-01

    The theory of electron bands, which arises from basic quantum mechanical principles, has been the cornerstone of solid state physics for over 60 years. Simply put, an energy band is an electron state in a solid whose energy varies with its momentum (similar to, but with a more complicated dependence than, how a free electron's energy is proportional to its momentum squared). Much attention over the last 15 years has been given to the study of band structure of surfaces and interfaces, especially as the applications of these two-dimensional systems have become increasingly important to industry and science. The ultraESCA endstation at beamline 7.01 at the Advanced Light Source was developed for very high-energy - (∼50 meV) and angular - ( 12 photons/sec) makes the detailed study of the evolution of bands possible. The authors are interested in learning how, when one forms a chemical bond between a metal and an overlaying atom or molecule, the resulting charge transfer to or from the adsorbate affects the surface bands. In some cases of interest, intermediate coverages lead to different band structure than at the extremes of clean and saturated surfaces. Surfaces of tungsten are particularly interesting, as their atomic geometry has been shown to be exquisitely sensitive to both the surface vibrational and electronic properties. In this study, the authors looked at the surface bands of tungsten ((110) surface), as a function both of coverage and mass of overlaying atoms. The adsorbed atoms were hydrogen and the alkali atoms lithium and cesium

  16. Dynamic Capacity and Delivery Performance of Adsorbed Hydrogen Tank Technology

    Science.gov (United States)

    Knight, Ernest; Gillespie, Andrew; Stalla, David; Prosniewski, Matthew; Smith, Adam; Pfeifer, Peter

    In an effort to reduce our carbon footprint and decrease our dependency on a finite fuel supply, mankind has been taking steps towards alternative fuel sources. One of the ideal fuel sources worth striving towards is hydrogen. Combusting hydrogen only produces water vapor and hydrogen is incredibly abundant. The largest hurdle of using hydrogen is the storage of the gas itself. Relying solely on compressing the gas requires large heavy gas cylinders for storage. The amount of gas stored at a given pressure can be greatly increased through the use of adsorbent materials. The nanoporous carbon powder we have used has achieved a gravimetric storage capacity of 31 g H2/kg C and a volumetric storage capacity of 8.7 g H2/L at room temperature and 100 bar. This was measured on our 5.3 L tank filled with our adsorbent material. This powder was able to be packed into the tank in such a way that we achieved a packing fraction of 0.63, which reflects the packing of random close packed spheres. We have used monoliths made from these powders to study the storage capabilities as well as the dynamic filling and discharging performance of our tank. With these monoliths, we are able to obtain a packing fraction of 0.96. We have also been able to measure gravimetric storage capacity of 20.4 g H2/kg C and a volumetric storage capacity of 11 g H2/L at 195 K and 50 bar on these monoliths. We hope to measure more of this 195 K isotherm as well as thorough isotherm and filling data at 273 K and 296 K.

  17. Strongly correlated systems experimental techniques

    CERN Document Server

    Mancini, Ferdinando

    2015-01-01

    The continuous evolution and development of experimental techniques is at the basis of any fundamental achievement in modern physics. Strongly correlated systems (SCS), more than any other, need to be investigated through the greatest variety of experimental techniques in order to unveil and crosscheck the numerous and puzzling anomalous behaviors characterizing them. The study of SCS fostered the improvement of many old experimental techniques, but also the advent of many new ones just invented in order to analyze the complex behaviors of these systems. Many novel materials, with functional properties emerging from macroscopic quantum behaviors at the frontier of modern research in physics, chemistry and materials science, belong to this class of systems. The volume presents a representative collection of the modern experimental techniques specifically tailored for the analysis of strongly correlated systems. Any technique is presented in great detail by its own inventor or by one of the world-wide recognize...

  18. Strongly Correlated Systems Theoretical Methods

    CERN Document Server

    Avella, Adolfo

    2012-01-01

    The volume presents, for the very first time, an exhaustive collection of those modern theoretical methods specifically tailored for the analysis of Strongly Correlated Systems. Many novel materials, with functional properties emerging from macroscopic quantum behaviors at the frontier of modern research in physics, chemistry and materials science, belong to this class of systems. Any technique is presented in great detail by its own inventor or by one of the world-wide recognized main contributors. The exposition has a clear pedagogical cut and fully reports on the most relevant case study where the specific technique showed to be very successful in describing and enlightening the puzzling physics of a particular strongly correlated system. The book is intended for advanced graduate students and post-docs in the field as textbook and/or main reference, but also for other researchers in the field who appreciates consulting a single, but comprehensive, source or wishes to get acquainted, in a as painless as po...

  19. Strongly correlated systems numerical methods

    CERN Document Server

    Mancini, Ferdinando

    2013-01-01

    This volume presents, for the very first time, an exhaustive collection of those modern numerical methods specifically tailored for the analysis of Strongly Correlated Systems. Many novel materials, with functional properties emerging from macroscopic quantum behaviors at the frontier of modern research in physics, chemistry and material science, belong to this class of systems. Any technique is presented in great detail by its own inventor or by one of the world-wide recognized main contributors. The exposition has a clear pedagogical cut and fully reports on the most relevant case study where the specific technique showed to be very successful in describing and enlightening the puzzling physics of a particular strongly correlated system. The book is intended for advanced graduate students and post-docs in the field as textbook and/or main reference, but also for other researchers in the field who appreciate consulting a single, but comprehensive, source or wishes to get acquainted, in a as painless as possi...

  20. Strongly nonlinear oscillators analytical solutions

    CERN Document Server

    Cveticanin, Livija

    2014-01-01

    This book provides the presentation of the motion of pure nonlinear oscillatory systems and various solution procedures which give the approximate solutions of the strong nonlinear oscillator equations. The book presents the original author’s method for the analytical solution procedure of the pure nonlinear oscillator system. After an introduction, the physical explanation of the pure nonlinearity and of the pure nonlinear oscillator is given. The analytical solution for free and forced vibrations of the one-degree-of-freedom strong nonlinear system with constant and time variable parameter is considered. Special attention is given to the one and two mass oscillatory systems with two-degrees-of-freedom. The criteria for the deterministic chaos in ideal and non-ideal pure nonlinear oscillators are derived analytically. The method for suppressing chaos is developed. Important problems are discussed in didactic exercises. The book is self-consistent and suitable as a textbook for students and also for profess...