WorldWideScience

Sample records for strip-mine spoil material

  1. Hydrologic modeling of reclaimed strip mine spoil

    International Nuclear Information System (INIS)

    Edwards, K.B.; Stoertz, M.W.; Turney, D.C.

    1998-01-01

    A numerical groundwater flow model (MODFLOW) of a surface coal mine in southeast Ohio was calibrated under steady state conditions to match measured heads by varying hydraulic conductivity (K) and recharge (R). Sensitivity studies indicated that K was not largely dependent on the poorly quantified underclay elevation or on the lake boundary condition. The baseflow recharge was determined to be between 8 and 60 mm/yr (1 to 6% of annual rainfall) and K between 0.004 and 0.01 cm/s for the spoil aquifer

  2. Raptor use of revegetated coal strip mine spoils in interior Alaska

    International Nuclear Information System (INIS)

    Elliott, C.L.

    1994-01-01

    Raptors associated with reclaimed coal strip mine spoils on the Usibelli Coal Mine in southcentral Alaska were observed in 1981 and 1982. Of the 10 raptor species identified on the mine, 6 (red-tailed hawk, golden eagle, Northern harrier, American kestrel, hawk owl, and short-eared owl) were observed hunting on the reclaimed areas

  3. Succession of insects on unreclaimed coal strip mine spoil banks in Indiana

    Energy Technology Data Exchange (ETDEWEB)

    Schrock, J.R.

    1984-01-01

    Selected sites at a western Indiana unreclaimed coal strip mine and adjacent undisturbed area sampled by Munsee in 1964 were restudied in 1981. Slope and exposure, soil pH and texture, vegetation and tree tallies, on-site rainfall and local weather records were used to characterize 18 spoilbanks and two unmined sites. Surface-active arthropods were sampled by replicated pitfall taps the summer of 1981 at the same locations and dates trapped by Munsee in 1964. Plant cover was sampled by a modified point-contact method. Trees over one inch dbh were tallied and measured for basal area. Clustering by similarity based on chi-square differences was performed for plants, trees, ants, springtails and ground beetles, using the undisturbed forest and a highly acid un-revegetated mined site as the extremes. Soil pH and texture changed rapidly on one moist spoilbank. Soil moisture levels generally decreased between 1964 and 1981 and depth of water penetration generally increased. Ant, springtail and carabid populations changed on revegetating sites. Myrmica spatulata and Smithistruma clypeata were major new ants on the sites in 1981. Iridomyrmex pruinosus analis and Pheidole bicarinata characteristic of barren spoilbanks in 1964 survived on only one remaining barren site in 1981. The collembolan Entomobrya quadrilineata decreased while Hypogastrura denticulata increased on the revegetating sites. Known habitat preference of some of these insects matched their occurrence on the spoilbanks.

  4. Placement of acid spoil materials

    Energy Technology Data Exchange (ETDEWEB)

    Pionke, H B; Rogowski, A S

    1982-06-01

    Potentially there are several chemical and hydrologic problems associated with placement of acid spoil materials. The rationale for a deep placement well below the soil surface, and preferably below a water table, is to prevent or minimize oxidation of pyrite to sulfuric acid and associated salts by reducing the supply of oxygen. If, however, substantial sulfuric acid or associated salts are already contained within the spoil because of present or previous mining, handling and reclamation operations (or if large supplies of indigenous salts exist, placement below a water table) may actually increase the rate of acid and salt leaching. Specific placement of acid- and salt-containing spoil should be aimed at preventing contact with percolating water or rising water tables. We recommend placement based on chemical and physical spoil properties that may affect water percolation O/sub 2/ diffusion rates in the profile. Both the deeper placement of acid spoil and coarser particle size can substantially reduce the amount of acid drainage. Placement above the water table with emphasis on percolate control may be better for high sulfate spoils, while placement below the non-fluctuating water table may be better for pyritic spoils.

  5. Useful materials from colliery spoil

    Energy Technology Data Exchange (ETDEWEB)

    Gibson, J

    1975-08-01

    This article is based on a paper presented by the author at a recent symposium on ''The technology of reclamation.'' He discusses the research that is being carried out at the N.C.B.'s Coal Research Establishment into ways of utilizing colliery spoil: unburnt spoil may be used in road construction as fill material or as cement-stabilized sub-bases; the heat-treated spoil can be used as lightweight aggregate in concrete blocks or as dense aggregate for non-skid roadstone. Information is also given about a project to examine the drying of washery tailings in a fluidized-bed combustion system: the material remaining in the bed is immediately usable as a lightweight aggregate, and the fine material blown from the bed and collected in cyclones might be used in the manufacture of cheap artifacts.

  6. Comparative limnology of strip-mine lakes

    Energy Technology Data Exchange (ETDEWEB)

    Parsons, J D

    1964-01-01

    Lakes were classified according to chemical properties. The concentration of the ferric iron oxides was responsible for a reddish-black turbidity which, in turn, played a major role in the thermal stratification of red strip-mine lakes. Owing to the lack of measurable turbidity and as a result of selective absorption of visible solar radiation, other strip-mine lakes appeared blue in color. The annual heat budget and the summer heat budget are essentially equivalent under saline conditions. Regardless of the physical and chemical conditions of the strip-mine lakes, heat income was a function of the circulating water mass. The progressive oxidation and precipitation of the iron oxides is the key to the classification of strip-mine lakes.

  7. Land restoration after strip mining for coal

    Energy Technology Data Exchange (ETDEWEB)

    Rickard, W. H.

    1977-01-01

    Recent legislation requires that lands surface mined for coal be returned to approximate original topography and vegetative cover be restored. Spoils provide poor rooting habitat because of extreme stoniness or excessive slope steepness which provide few niches for seeds to become lodged and also spoil may provide poor mineral nutrition, poor water retention and sometimes the spoil may even have chemical properties detrimental to plant growth (acidity, alkalinity or even unusually large amounts of toxic mineral elements i.e., copper, sodium). To provide a substrate better suited for plant growth, recommendations for restoration call for deep burial of unfavorable substrate components i.e., rocks and materials of unusual chemistry and the dressing of reshaped spoil with topsoil i.e., material with the most favorable properties for plant growth. Even though all the substrate requirements for healthy plant growth may be met, such as adding a form of available nitrogen as fertilizer, plants will not grow if weather conditions are extreme. For example, in very dry (desert) climates precipitation may be too scanty or too erratic to permit the successful establishment of many kinds of plants. Even under the most favorable conditions plant productivity averaged over a period of years is low. Also in very cold climates the growing season may be limited to only a few weeks in summer e.g., arctic and alpine tundra regions. This shortens the time available for photosynthesis and keeps plant productivity low.

  8. Hydroseeding on anthracite coal-mine spoils

    Science.gov (United States)

    Miroslaw M. Czapowskyj; Ross Writer

    1970-01-01

    A study was made of the performance of selected species of legumes, grasses, and trees hydroseeded on anthracite coal-mine spoils in a slurry of lime, fertilizer, and mulch. Hydroseeding failed on coal-breaker refuse, but was partially successful on strip-mine spoils.

  9. Determining pH of strip-mine spoils

    Science.gov (United States)

    W. A. Berg

    1969-01-01

    Results with the LaMotte-Morgan method for determining soil pH-or the solution modification of this method-usually agreed fairly well with the results from using a pH meter, the recognized standard. Results obtained with the Soiltex and Hellige-Truog methods often deviated somewhat from the pH meter readings; and the Hydrion papers and the Kelway pH tester often gave...

  10. Reforestation of strip-mined lands in West Virginia

    Science.gov (United States)

    H. Spencer Potter; Sidney Weitzman; George R., Jr. Trimble

    1951-01-01

    The early 1940's witnessed a striking increase in strip-mining throughout the eastern coal region. West Virginia, with its extensive coal resources, naturally was caught in the full current of this shift in mining methods. Today the raw gash on the hillside - almost infallibly the mark of a strip-mine operation - is a familiar sight in the State.

  11. Erodibility of surface-mine spoil banks in southeastern Ohio : an approximation

    Energy Technology Data Exchange (ETDEWEB)

    McKenzie, C D; Studlick, J R.J.

    1979-07-01

    Measurements of accumulated sediment in inter-bank basins of unreclaimed strip mines determined the average annual site loss from unvegetated, 18-year-old spoil banks. Assuming that the universal soil loss equation (USLE) can be used to estimate sediment yield from strip mine slopes, the topographic factor in the USLE was determined in 2 ways, and values for erodibility well calculated. The technique is applicable to unreclaimed mines where inter-bank basins trap all slope-derived sediment.

  12. Effect of Strip Mining on Water Quality in Small Streams in Eastern Kentucky, 1967-1975

    Science.gov (United States)

    Kenneth L. Dyer; Willie R. Curtis

    1977-01-01

    Eight years of streamflow data are analyzed to show the effects of strip mining on chemical quality of water in six first-order streams in Breathitt County, Kentucky. All these watersheds were unmined in August, 1967, but five have since been strip mined. The accumulated data from this case history study indicate that strip mining causes large increases in the...

  13. Soybean growth on fly ash-amended strip mine soils

    Energy Technology Data Exchange (ETDEWEB)

    Fail, Jr, J L; Wochok, Z S

    1977-01-01

    The use of fly ash as an amendment for strip mine soils has been studied under field conditions. Soils ranging in pH from 4.0 to 6.0 were tested. The addition of fly ash in all cases was effective as an acid soil neutralizer and substantially enhanced the growth and development of all experimental plants. The parameters used in growth analyses were plant height, dry weight, root/shoot ratios, nodulation, pod production, and nitrogen fixing capacity for legumes.

  14. Establishing native warm season grasses on Eastern Kentucky strip mines

    Energy Technology Data Exchange (ETDEWEB)

    Barnes, T.G.; Larkin, J.L.; Arnett, M.B. [Univ. of Kentucky, Lexington, KY (United States). Dept. of Forestry

    1998-12-31

    The authors evaluated various methods of establishing native warm season grasses on two reclaimed Eastern Kentucky mines from 1994--1997. Most current reclamation practices incorporate the use of tall fescue (Festuca arundinacea) and other cool-season grasses/legumes that provide little wildlife habitats. The use of native warm season grasses will likely improve wildlife habitat on reclaimed strip mines. Objectives of this study were to compare the feasibility of establishing these grasses during fall, winter, or spring using a native rangeland seeder or hydroseeding; a fertilizer application at planting; or cold-moist stratification prior to hydroseeding. Vegetative cover, bare ground, species richness, and biomass samples were collected at the end of each growing season. Native warm season grass plantings had higher plant species richness compared to cool-season reclamation mixtures. There was no difference in establishment of native warm season grasses as a result of fertilization or seeding technique. Winter native warm season grass plantings were failures and cold-moist stratification did not increase plant establishment during any season. As a result of a drought during 1997, both cool-season and warm season plantings were failures. Cool-season reclamation mixtures had significantly more vegetative cover and biomass compared to native warm season grass mixtures and the native warm season grass plantings did not meet vegetative cover requirements for bond release. Forbs and legumes that established well included pale purple coneflower (Echinacea pallida), lance-leaf coreopsis (Coreopsis lanceolata), round-headed lespedeza (Lespedeza capitata), partridge pea (Cassia fasiculata), black-eyed susan (Rudbeckia hirta), butterfly milkweed (Asclepias tuberosa), and bergamot (Monarda fistulosa). Results from two demonstration plots next to research plots indicate it is possible to establish native warm season grasses on Eastern Kentucky strip mines for wildlife habitat.

  15. Establishing native warm season grasses on Eastern Kentucky strip mines

    International Nuclear Information System (INIS)

    Barnes, T.G.; Larkin, J.L.; Arnett, M.B.

    1998-01-01

    The authors evaluated various methods of establishing native warm season grasses on two reclaimed Eastern Kentucky mines from 1994--1997. Most current reclamation practices incorporate the use of tall fescue (Festuca arundinacea) and other cool-season grasses/legumes that provide little wildlife habitats. The use of native warm season grasses will likely improve wildlife habitat on reclaimed strip mines. Objectives of this study were to compare the feasibility of establishing these grasses during fall, winter, or spring using a native rangeland seeder or hydroseeding; a fertilizer application at planting; or cold-moist stratification prior to hydroseeding. Vegetative cover, bare ground, species richness, and biomass samples were collected at the end of each growing season. Native warm season grass plantings had higher plant species richness compared to cool-season reclamation mixtures. There was no difference in establishment of native warm season grasses as a result of fertilization or seeding technique. Winter native warm season grass plantings were failures and cold-moist stratification did not increase plant establishment during any season. As a result of a drought during 1997, both cool-season and warm season plantings were failures. Cool-season reclamation mixtures had significantly more vegetative cover and biomass compared to native warm season grass mixtures and the native warm season grass plantings did not meet vegetative cover requirements for bond release. Forbs and legumes that established well included pale purple coneflower (Echinacea pallida), lance-leaf coreopsis (Coreopsis lanceolata), round-headed lespedeza (Lespedeza capitata), partridge pea (Cassia fasiculata), black-eyed susan (Rudbeckia hirta), butterfly milkweed (Asclepias tuberosa), and bergamot (Monarda fistulosa). Results from two demonstration plots next to research plots indicate it is possible to establish native warm season grasses on Eastern Kentucky strip mines for wildlife habitat

  16. Microbial ecology of acid strip mine lakes in southern Indiana

    International Nuclear Information System (INIS)

    Gyure, R.A.

    1986-01-01

    In this study, the author examined the limnology and microbial ecology of two acid strip mine lakes in the Greene-Sullivan State Forest near Dugger, Indiana. Reservoir 29 is a larger lake (225 ha) with water column pH of 2.7 and sediment pH of 3.8. Lake B, a smaller (20 ha) lake to the south of Reservoir 29, also has an acidic water column (pH 3.4) but more neutral sediments (pH 6.2). Both have very high sulfate concentrations: 20-30 mM in the water column and as high as 100 mM in the hypolimnion of Lake B. Low allochthonous carbon and nutrient input characterize these lakes as oligotrophic, although algal biomass is higher than would be expected for this trophic status. In both lakes, algal populations are not diverse, with a few species of single-celled Chlorophyta and euglenoids dominating. Algal biomass is concentrated in a thin 10 cm layer at the hypolimnion/metalimnion interface, although light intensity at this depth is low and severely limits productivity. Bacterial activity based on 14 C-glucose incorporation is highest in the hypolimnion of both lakes, and sulfate-reduction is a dominant process in the sediments. Rates of sulfate-reduction compare with those in other freshwater environments, but are not as high as rates measured in high sulfate systems like saltmarsh and marine sediments

  17. Area Strip Mine Reclamation Using Dredged Material: A Field Demonstration.

    Science.gov (United States)

    1980-07-01

    COMMON BEGGAR’S TICK Bidens frondosa COMMON EVENING PRIMROSE Oenothera biennis COMMON ORACH Atriplex patula COMMON REED Phraginites communis...altissima ACERACEAE BOX ELDER Acer negundo RHAMNACEAE COMMON BUCKTHORN Rhamnus cathartica A8 r ONAGRACEAE COMMON EVENING PRIMROSE Oenothera biennis

  18. Prairie revegetation of a strip mine in Illinois: fifteen years after establishment

    Energy Technology Data Exchange (ETDEWEB)

    Corbett, E.A.; Anderson, R.C.; Rodgers, C.S. [Illinois State University, Normal, IL (United States). Dept. of Biological Sciences

    1996-12-01

    The long-term success of prairie planting on a former strip mine in northeastern Illinois was investigated. The site was reclaimed and planted with prairie species in the 1970s. Total biomass increased over time, largely as a result of an increase in biomass of non-prairie species. Biomass of prairie species remained unchanged because of an increase in Panicum virgatum (switchgrass) offsetting decreases in Sorghastrum nutans (Indian grass).

  19. The planning and operation of open-pit and strip mines: proceedings of an international conference held at the University of Pretoria, 9-13 April 1984

    International Nuclear Information System (INIS)

    Deetlefs, J.P.

    1986-01-01

    This book records the proceedings of the second international conference on the theme of planning and operation of open-pit and strip mines. The conference was held in Pretoria during April 1984. The major portion of South African iron ore and copper is mined in open-pit mines. The rapid expansion of the open-pit and strip mining industry has led to the thriving industry of today. Notable areas of growth have been the introduction of capital-intensive machinery such as walking drag-lines, large capacity shovels, in-pit crushers, extensive use of conveyor belts, large haul tracks and ore-dressing plants. Among other areas where corresponding progress has been made are blasting techniques, maintenance planning, computer applications, and large-scale stock-piling of bulk materials. The conference touched on all these subjects under four main headings: mine planning, mining operations, equipment selection and maintenance, and new developments. One paper looks at open-pit production control at Rossing Uranium Limited

  20. Bryophytes and revegetation of coal spoils in southern Iowa. [14 refs

    Energy Technology Data Exchange (ETDEWEB)

    Carvey, K.; Farrar, D.R.; Glenn-Lewin, D.C.

    1976-01-01

    Strip mining of coal in southern Iowa has left many scattered areas of coal spoils which provide a type of habitat unique to the region. The occurrence and distribution of 29 mosses and 2 liverworts on these spoils was determined and related to the general process of spoil revegetation. The spoil bryophyte flora was compared with Conard's (1956) list of bryophytes for the region. An increase in per cent cover and in species diversity of bryophytes was observed with increasing age of spoils, and was correlated with increased vascular plant cover. Dicranella heteromalla and Ceratodon purpureus were found to be common throughout the spoils, whereas all other species were limited to more protected sites, especially on north-facing slopes. Mosses did not appear to colonize very exposed areas on the spoils, but were limited to areas with some protection provided, especially by vascular plants. Several disjunct or highly localized moss populations were found including one new state record and thirteen new county records.

  1. Biomarker assessment of the effects of strip mine contamination on channel catfish

    International Nuclear Information System (INIS)

    Martin, L.K. Jr.; Black, M.C.

    1994-01-01

    A suite of biomarkers were used to evaluate acute (1 day) to semi-chronic (3 month) heavy metal-induced toxicity in channel catfish, Ictalurus punctatus, caged at an abandoned strip mine and a noncontaminated reference site. Assays performed include indicators of metabolic, hematological, osmoregulatory, and genotoxic stress. Two cage designs were utilized to evaluate the importance of exposure routes; one allowing exclusive contact with the water column and the other allowing contact with water and sediments. Significant DNA strand breakage was observed in catfish exposed in both regimes, but DNA repair was observed only in water-exposed catfish. Transient increases in hemoglobin, ALAD, and hematocrit levels were observed at 1 month for both exposure regimes, followed by a return to control levels for the duration of the study. Environmental conditions (i.e., changes in water quality and temperature) may have contributed to the variable plasma chloride and glucose levels observed in all catfish exposed to strip mine wastes. Further analysis of the data with non-metric clustering techniques and correlations with tissue metal residues may yield more insights into causal relationships

  2. Lost Mountain: a year in the vanishing wilderness; radical strip mining and the devastation of Appalachia

    Energy Technology Data Exchange (ETDEWEB)

    Reece, E.

    2007-02-15

    The mountains of Appalachia are home to one of the great forests of the world - they predate the Ice Age and scientists refer to them as the 'rainforests' of North America for their remarkable density and species diversity. These mountains also hold the mother lode of American coal, and the coal mining industry has long been the economic backbone for families in a region hard-pressed for other job opportunities. But recently, a new type of mining has been introduced -'radical strip mining', aka 'mountaintop removal'- in which a team employing no more than ten men and some heavy machinery literally blast off the top of a mountain, dump it in the valley below, and scoop out the coal. Erik Reece chronicles the year he spent witnessing the systematic decimation of a single mountain, aptly named 'Lost Mountain'. A native Kentuckian and the son of a coal worker, Reece makes it clear that strip mining is neither a local concern nor a radical contention, but a mainstream crisis that encompasses every hot-button issue - from corporate hubris and government neglect, to class conflict and poisoned groundwater, to irrevocable species extinction and landscape destruction. Published excerpts of Lost Mountain are already driving headlines and legislative action in Kentucky.

  3. The biological costs of not reclaiming bentonite mine spoils

    Science.gov (United States)

    Carolyn Hull Sieg; Daniel W. Uresk; Richard M. Hansen

    1982-01-01

    Bentonite clay has been mined in the northern Great Plains for more than 80 years. Until the late 1960's, mine spoil materials were left in steep piles and no effort was made to restore biological productivity to these disturbed sites. As a result, unreclaimed spoils are barren and eroded. The biological costs of not reclaiming these spoils are examined in this...

  4. Spoiled child syndrome.

    Science.gov (United States)

    McIntosh, B J

    1989-01-01

    People often speak of children as being "spoiled" and many parents worry about the possibility of spoiling their infants and children. Many pediatricians, however, are uncomfortable with this term because it is a poorly defined and derogatory expression. Some would even deny that infants and children can be spoiled. Avoiding the use of the expression spoiled can create difficulties in communicating with parents concerned about their children's behavior. In this article, the spoiled child syndrome will be defined and those patterns of behavior that characterize it will be distinguished from other patterns of difficult behavior which may be confused with it. The spoiled child syndrome is characterized by excessive self-centered and immature behavior, resulting from the failure of parents to enforce consistent, age-appropriate limits. Many of the problem behaviors that cause parental concern are unrelated to spoiling as properly understood. Such behaviors are often age-related normal behaviors, reactions to family stresses, or patterns of behavior determined by factors inherent in the child. Pediatricians can provide counseling and reassurance for such behaviors and, by helping parents understand the etiology of true spoiling, can encourage the use of behavior modification techniques for its prevention and treatment.

  5. Spoils of Truce

    DEFF Research Database (Denmark)

    Haugbølle, Sune

    2014-01-01

    Review of Spoils of Truce. Corruption and stat building in Postwar Lebanon Reinoud Leenders Ithaca, NY, Cornell University Press, 2012, ISBN 978-0-8014-5100-3......Review of Spoils of Truce. Corruption and stat building in Postwar Lebanon Reinoud Leenders Ithaca, NY, Cornell University Press, 2012, ISBN 978-0-8014-5100-3...

  6. Protective-decorative revegetation of spoil banks in the Donbass

    Energy Technology Data Exchange (ETDEWEB)

    Baklanov, V.I.; Podkopaev, A.A.

    1985-05-01

    Spoil bank reclamation in the Donbass is discussed, where there were 1195 spoil banks from underground coal mines in 1984, 80% of which were conic shaped. The average spoil bank was 60 to 80 m high, base surface was 4.2 ha, volume amounted to 1,144,000 mT. Ninety-five spoil banks were situated in cities or towns and were a source of environmental pollution. Reclamation of a spoil bank in the No 6/14 coal mine in the Makeevugol' association is analyzed. Buildup of the spoil bank started in 1930. The spoil bank was 72 m high, its base was 8.05 ha large, slopes were inclined at 25 to 36 degrees, volume of material amounted to 2.2 million mT. From 1973 to 1978 shape of the spoil bank was changed: its height was reduced to 40 m, slope inclination was reduced to 25 degrees. Spontaneous combustion was controlled by changing spoil bank shape. Slopes were divided into a number of terraces. The spoil bank was covered with a 0.3 m thick soil cover suitable for vegetation. Sainfoin (Onobrychis) was sown on leveled zones of the spoil bank and false acacia (Robinia pseudoacacia) was planted on the terraces. Plant growth in the first and second years was satisfactory.

  7. Determination of the algal growth-limiting nutrients in strip mine ponds

    International Nuclear Information System (INIS)

    Bucknavage, M.J.; Aharrah, E.C.

    1984-01-01

    Using both a test organism, Ankistrodesmus falcatus, and natural phytoplankton, the Printz Algal Assay Bottle Test was used to determine the algal growth limiting nutrients in two strip mine ponds. Nitrogen, phosphorus, and iron were investigated, singly and in combination, as possible limiting nutrients. A synthetic chelator, Na 2 EDTA, was also used in the assay to test for the presence of metal toxicants and/or trace metal limitation. Because bacteria have a major influence on water chemistry, a separate assay incorporating the natural bacteria population was performed. In both ponds, assay results using test alga indicate phosphorus to be the primary limiting nutrient and nitrogen as a secondary factor. The presence of EDTA in combination with phosphate containing treatment promoted a higher algal concentration in both ponds. Iron was determined to be a secondary limiting nutrient in only one of the ponds. Natural phytoplankton of the two ponds responded in a similar manner to nutrient increases. Only one pond had the same results produced by both assays. Nutrient availability was influenced by the presence of bacteria in one pond but not in the other

  8. Characterization of three acid strip mine lakes in Grundy County, Illinois

    Energy Technology Data Exchange (ETDEWEB)

    Master, W. A.

    1979-09-01

    Three small lakes with acid water and one with circumneutral water at an abandoned strip mine site were characterized to identify factors limiting biological productivity. Dissolved oxygen, specific conductance, and temperature profiles were determined. Water samples were analyzed for 23 parameters, and the lakes were examined for the presence of aquatic vascular plants and benthic inhabitants. The acid lakes ranged from 0.9 ha to 2.7 ha in surface area and from 3.1 m to 6.7 m in maximum depth. The mean pH of the acid lakes ranged from 3.1 to 3.9. Chemicals found at concentrations higher than Illinois surface water standards or federal criteria for the protection of aquatic life included Cd, Cu, Fe, Mn, SO/sub 4/=, and Zn. A number of these chemicals were at sufficiently high concentrations to limit the survival and productivity of most aquatic fauna. The lake with the poorest water quality had the least diversity of aquatic vascular plants and benthic invertebrates, while the circumneutral lake had the greatest diversity of species.

  9. Characterization of dust samples from a coal strip mine using a resuspension chamber

    Directory of Open Access Journals (Sweden)

    Martin Civiš

    2017-06-01

    Full Text Available A metallic cylindrical resuspension chamber (V = 0.437 m3, S = 0.35 m2, S/V = 8.38 was constructed to disperse samples of soil and various kinds of dust. The chamber allows on-line determination of number/mass size distribution of aerosol particles formed by dispersion and subsequent sampling of size-segregated particles on filter media. The samples tested were lignite, power plant flue ash and overburden soil from the Nastup coal strip mine in Northern Bohemia. About 20 mg of the individual samples were pneumatically dispersed by 0.5 liter of pressurized air inside the chamber under defined temperature and humidity conditions. Then the dynamics of aerosol size distributions was recorded using an aerodynamic particle sizer with a frequency of 5 seconds. The lignite and flue ash contributed most to the mass of atmospheric aerosol particles smaller than 10/2.5 micrometer – PM10/ PM2.5. The re-suspended mass of the samples varied between 0.001% for overburden soil and 0.32% for mine road soil. The aerosolized lignite and flue ash samples, sampled by a Harvard Impactor and a Personal Cascade Impactor Sampler, revealed that the ash contained higher amounts of fine particles than the lignite and subsequent chemical analyses, carried out using SEM-EDX, reveals that the PM2.5 fraction formed by dispersion of the ash samples had the highest content of sulphur, and PM10 was dominated by Si. PM10 was closest to mullite, while the PM2.5 fraction contained sulphides, pyrites, pyrrhotites and polytypes of sulphide. The PM1 fraction was dominated by quartz glass. The fractions of sizes 2.5–1 μm and 0.5–0.25 μm were dominated by Si and S, respectively.

  10. Habitat use and food habits of snowshoe hares associated with a reclaimed strip mine in interior Alaska

    International Nuclear Information System (INIS)

    Elliott, C.L.

    1998-01-01

    The value of reclaimed coal stripmine spoils as snowshoe hare (Lepus americanus) habitat in interior Alaska was examined. Hare density in 3 cover types (tall shrub, conifer forest, revegetated lands) was determined using the pellet plot method. Hare food habits were determined via microhistological examination of fecal material. Snowshoe hares used the tall shrub cover type more than any other habitat examined. Hare density in the shrub zone was 10/ha in winter and 18/ha in summer. Shrubs (mainly willow species) comprised the major portion of the summer diet (69%), while spruce made up 51% of the winter diet. Based on dietary data and habitat use, the long-term loss of coniferous forests and tall shrubs due to mining, and the lack of emphasis on the re-establishment of woody vegetation in present reclamation procedures; will greatly reduce and possibly eliminate snowshoe hare populations on large-scale surface coal mines in the northern boreal regions

  11. Factors of Reclamation Success at the Lignite Strip-Mined Land in Northern Greece

    Directory of Open Access Journals (Sweden)

    Thomas Panagopoulos

    2013-06-01

    Full Text Available The adverse ecological conditions at the lignite mines of Ptolemaida make the landscape reclamation difficult. The naturally established vegetation and soil properties were studied prior to reclamation. Various forest species were planted to assess the afforestation potential. The natural vegetation was heterogeneous but can be used for the analysis of the site. The soil of the spoil heaps was heterogeneous with unfavourable physicochemical properties. Surface soil temperature was still 24º C higher in bare soil than in soil covered with vegetation. The most successful species of the afforestation trial were Robinia pseudoacacia and Cedrus atlantica. Covering of fly ash spoils with topsoil presented poor results, while sewage sludge gave a favorable amelioration response in areas with high fly ash content. Topsoil from older stands was the suggested method to establish Robinia pseudoacacia. Reclamation success was dependent on appropriate planning; thus, the new landscape had to be designed in harmony with the surrounding landscape before the start of the mining activity.

  12. Plant growth inhibition by soluble salts in sewage sludge-amended mine spoils

    Energy Technology Data Exchange (ETDEWEB)

    Rodgers, C.S.; Anderson, R.C. [Illinois State University, Normal, IL (United States). Dept. of Biological Sciences

    1995-07-01

    The growth response of prairie switchgrass {ital Panicum virgatum}L was compared in strip mine spoil amended with various levels of anaerobically digested waste-activated sewage sludge (0, 56, 111, 222, or 333 dry Mg ha{sup -1}) and commercial fertilizer, pure sludge, and glasshouse soil. Plants were grown in a growth chamber and substrates were maintained at field capacity during the study. Soluble salt concentrations of the substrates increased linearly as a function of sludge amendment and were within the range known to inhibit the growth of many plant species at the high levels of sludge application. There was, however, a linear response of biomass production to increasing levels of sludge amendment. Maintaining substrates at field capacity apparently prevented the high concentration of soluble salts from inhibiting plant growth. The increased biomass yield associated with sludge application was likely due to the increased availability of inorganic nutrients associated with sludge amendment. 22 refs., 2 figs., 2 tabs.

  13. Distribution of vesicular-arbuscular mycorrhizal fungi in coal, lignite and calcite mine spoils of India

    Energy Technology Data Exchange (ETDEWEB)

    Ganesan, V.; Ragupathy, S.; Parthipan, B.; Rani, D.B.R.; Mahadevan, A.

    1991-12-31

    Vesicular-arbuscular mycorhizzal (VAM) status was assessed for coal, lignite and calcite mine spoils. The three study sites were: The Kothagudem coal field in the south central region where waste materials are piled 1 to 2 m high on the soil surface. Samples were collected from plants growing on the waste. Neyveli, on the southeastern coast, is a lignite coal mine where the spoil is piled 70 to 100 m high on the soil surface. Samples were collected from recently revegetated mine spoil and from 25 year old revegetated sites. The calcite mine at Thazhaiyuthu in the south where the spoil is piled up 2 to 3 m on the soil surface. Samples were collected from 4 to 7 year old reclaimed sites. The wastes generally supported different plant species. The level of VAM infection of plants was markedly different in each mine spoil, with the maximum infection in the coal and calcite spoils, and the least in the lignite spoil. There was more infection in the 25 year old lignite spoil than in the newly revegetated spoil. There were different VAM species in each spoil, and no one species was present in all of the samples. The authors conclude that one of the factors leading to the differences between spoils is the amount of topsoil contained in the spoil (least in the lignite spoils which are very deep). The other is age of the spoils. Unfortunately the authors concluded that the best approach is to enrich the spoils with VAM rather than salvaging and replacing topsoil

  14. Mathematic simulation of mining company’s power demand forecast (by example of “Neryungri” coal strip mine)

    Science.gov (United States)

    Antonenkov, D. V.; Solovev, D. B.

    2017-10-01

    The article covers the aspects of forecasting and consideration of the wholesale market environment in generating the power demand forecast. Major mining companies that operate in conditions of the present day power market have to provide a reliable energy demand request for a certain time period ahead, thus ensuring sufficient reduction of financial losses associated with deviations of the actual power demand from the expected figures. Normally, under the power supply agreement, the consumer is bound to provide a per-month and per-hour request annually. It means that the consumer has to generate one-month-ahead short-term and medium-term hourly forecasts. The authors discovered that empiric distributions of “Yakutugol”, Holding Joint Stock Company, power demand belong to the sustainable rank parameter H-distribution type used for generating forecasts based on extrapolation of such distribution parameters. For this reason they justify the need to apply the mathematic rank analysis in short-term forecasting of the contracted power demand of “Neryungri” coil strip mine being a component of the technocenosis-type system of the mining company “Yakutugol”, Holding JSC.

  15. Strip mining with hydraulic shover and cross-pit stacker; Tagebau mit hydraulischen Hochloeffelbagger und Direktversturz-Absetzer

    Energy Technology Data Exchange (ETDEWEB)

    Streck, W. [Dipl.-Ing. Willibald Streck, Boden, Wasser, Rohstoff, Bruehl (Germany)

    2005-09-01

    In the standard strip mining of sedimentary deposits draglines are used for overburden removal. In this paper an alternative is presented which offers significantly lower initial investment costs and equal operating and maintenance costs. It is applicable in certain mining conditions. The stripping system consists of a standard hydraulic shovel excavator loading into a hopper/stacker on crawlers (XPS). With a shovel of 34 m{sup 3} size the stripping height is limited to approximately 15 to 17 m. Cuts of 15 to 20 m width may be worked. The XPS may have a hopper size of 70 m{sup 3} and a discharge boom of 70 m. The system reaches an annual capacity in the range of 12 mill bank m{sup 3}. It compares well with a standard dragline of the Bucyrus W 2000 type. While the operating and maintenance cost per bank m{sup 3} are about the same, the initial investment costs differ drastically, about 16 mill US-Dollar for the shovel/XPS compared to 24 mill US-Dollar for the dragline. In new surface mining projects and under distinct mining conditions the low investment costs and other advantages may balance the limitations of the shovel/XPS system and justify the deviation from the standard stripping dragline. (orig.)

  16. Phytoremediation of coal mine spoil dump through integrated biotechnological approach

    Energy Technology Data Exchange (ETDEWEB)

    Juwarkar, A.A.; Jambhulkar, H.P. [National Environmental Engineering Research Institute, Nagpur (India)

    2008-07-15

    Field experiment was conducted on mine spoil dump on an area of 10 ha, to restore the fertility and productivity of the coal mine spoil dump using integrated biotechnological approach. The approach involves use of effluent treatment plant sludge (ETP sludge), as an organic amendment, biofertilizers and mycorrihzal fungi along with suitable plant species. The results of the study indicated that amendment with effluent treatment plant sludge (ETP sludge), at 50 ton/ha improved the physico-chemical properties of coal mine spoil. Due to biofertilizer inoculation different microbial groups such as Rhizobium, Azotobacter and VAM spores, which were practically absent in mine spoil improved greatly. Inoculation of biofertilizer and application of ETP sludge helped in reducing the toxicity of heavy metals such as chromium, zinc, copper, iron, manganese lead, nickel and cadmium, which were significantly reduced to 41%, 43%, 37%, 37%, 34%, 39%, 37% and 40%, respectively, due to the increased organic matter content in the ETP sludge and its alkaline pH (8.10-8.28), at which the metals gets immobilized and translocation of metals is arrested. Thus, amendment and biofertilizer application provided better supportive material for anchorage and growth of the plant on coal mine spoil dump.

  17. The uses of ERTS-1 imagery in the analysis of landscape change. [agriculture, strip mining forests, urban-suburban growth, and flooding in Tennessee, Kentucky, Mississippi, and Alabama

    Science.gov (United States)

    Rehder, J. B. (Principal Investigator)

    1974-01-01

    The author has identified the following significant results. The analysis of strip mining from ERTS-1 data has resulted in the mapping of landscape changes for the Cumberland Plateau Test Site. Several mapping experiments utilizing ERTS-1 data have been established for the mapping of state-wide land use regions. The first incorporates 12 frames of ERTS-1 imagery for the generalized thematic mapping of forest cover for the state of Tennessee. In another mapping effort, 14 ERTS-1 images have been analyzed for plowed ground signatures to produce a map of agricultural regions for Tennessee, Kentucky, and the northern portions of Mississippi and Alabama. Generalized urban land use categories and transportation networks have been determined from ERTS-1 imagery for the Knoxville Test Site. Finally, through the analysis of ERTS-1 imagery, short-lived phenomena such as the 1973 spring floods on the Mississippi River in western Tennessee, have been detected, monitored, and mapped.

  18. Organization of radiation inspection for strip-mining development for ores with elevated content of natural radionuclides on the Karazhyra coal mine

    International Nuclear Information System (INIS)

    Lukashenko, S.N.; Subbotin, S.B.; Ajdarkhanov, A.O.; Medvedev, P.P.

    2003-01-01

    Due to existence of anomalous areas of ores with elevated content of natural radionuclides on the Karazhyra coal mine the project of its selective development was implemented. The project provides a set of measures on radiation safety. In the present paper the order of radiological operations organization and performance are shown, and methodical provision of these works is considered. Results of the preliminary radiological examination of the area, fulfilment the measures on mine works technology radiological safety, and strip-mining ores deposition are analyzed. The evaluations of natural radionuclides content with taking into account its influence on personnel during works fulfilment are made. The results of soil samples analysis are presented in the graphical form. The suggestions and recommendations on radiation monitoring improvement on the area are given

  19. Reclamation of opencut spoil piles

    Energy Technology Data Exchange (ETDEWEB)

    1976-07-01

    A successful reclamation program requires definite physical/engineering guidelines, a specific time commitment and to be fully integrated in the mining operation enabling most efficient use of available resources. This statement should be immediately qualified by saying that there must be enough flexibility to allow for varying mine layouts, plans and conditions. Mine conditions include physical and chemical spoil properties, climatic conditions and local topographic effects. Whilst reclamation is the responsibility of individual mine managers, the author undertakes a co-ordinating function amongst mine environmental officers to ensure that experience gained is recorded. Exchange of information between mines is maintained and there is a minimum duplication of effort.

  20. Environmental research - development of the material balance of oak tree ecosystems on quaternary spoil bank substrates of coal mines; Umweltforschung - Entwicklung des Stoffhaushaltes von Eichenoekosystemen auf quartaeren Kippsubstraten des Braunkohlenbergbaues

    Energy Technology Data Exchange (ETDEWEB)

    Katzur, J.; Knoche, D.

    2000-07-01

    Investigations have shown that even the very first forest generation on spoil banks already have high vitality. However, it is well known that pioneering terrestrial ecosystems have a high water and material turnover dynamics which will quickly influence the soil at that site but is not an indication of the development of a stable ecosystem. Long-term measurements were therefore made in oak forest ecosystems on quaternary spoil bank sands in order to achieve a quantification (Boxberg: Q. rubra L., 2 years; Kleinleipisch: Q. rubra L., 21 years; Annahuetter: Q. rubra L., 63 years). The results were compared with a virgin soil reference site (Neusorgefeld: Q. rubra L., 41 years). [German] Seit Jahrzehnten praegen Braunkohlentagebaue das Landschaftsbild und den Wasserhaushalt der Niederlausitz. Bislang wurden ca. 770 km{sup 2} ueberwiegend forstlich genutzter Flaechen devastiert und auf 2.100 km{sup 2} rund 9,5 Mrd. m{sup 3} statischer Grundwasservorraete entnommen. Im Zuge der seit 1990 drastisch verringerten Kohlefoerderung und forcierten Bergbausanierung erreicht die Rekultivierungsflaeche zwischenzeitlich rund 450 km{sup 2}, wobei die forstliche Folgenutzung mit 60% der Flaeche dominiert. Zahlreiche wachstumskundliche Untersuchungen belegen, dass sich bereits in der ersten Waldgeneration auf Kippe wuechsige und vitale Bestaende etablieren. Vegetations- und ertragskundliche Parameter wie z.B. Artenzusammensetzung, Naehrstoffversorgung, laufender Zuwachs oder Vorratshaltung sind jedoch per se noch keine hinreichenden Kriterien zur Einschaetzung der Entwicklungsdynamik und damit des angestrebten Rekultivierungserfolgs. Bekannterweise zeichnen sich im Aufbau befindliche terrestrische Oekosysteme generell durch eine ausgepraegte Wasser- und Stoffdynamik aus, welche im Zuge bodengenetischer Prozesse meist eine rasche Standortveraenderung bewirkt. Da das Standortpotential zum Rekultivierungszeitpunkt nicht prognostiziert werden kann, ist offen, ob sich bereits in der

  1. Definition of rehabilitation strategies for pre-strip tertiary spoil at coal mines in central Queensland

    International Nuclear Information System (INIS)

    Bell, L.C.; Mulligan, D.R.; Mitchell, R.J.; Philp, M.W.; Roe, P.A.

    1994-01-01

    In the open-cut coal mines of central Queensland, the conventional dragline removal of overburden results in a spoil surface dominated by Permian sediments. In recent years, however, a number of mines have changed their coal exposure methods to include a pre-stripping operation to create a bench for the dragline up to 50 m below the surface. This approach has allowed economic coal recovery from greater depths, but, since this pre-strip material is being deposited on existing spoil piles, it has resulted in a major change in the type of spoil material on the surface. The aims of this project were, firstly, to define the characteristics of this pre-strip material that could cause problems for the establishment and growth of both introduced pasture grasses and native tree species, and secondly, to explore possible spoil amendments which could ameliorate some or all of these limitations. Analyses on the range of spoils included pH, EC and sodicity. Straw mulch also reduced the crust strength and was an effective means of improving vegetative establishment. A complementary field trial was established at Saraji mine in April 1991, and after 4 months, treatments which involved a 30 cm capping of soil on the spoil resulted in the highest densities of tree seedling

  2. Phytoremediation of spoil coal dumps in Western Donbass (Ukraine)

    Science.gov (United States)

    Klimkina, Iryna; Kharytonov, Mykola; Wiche, Oliver; Heilmeier, Hermann

    2017-04-01

    At the moment, in Ukraine about 150 thousand hectares of fertile land are occupied by spoil dumps. Moreover, this figure increases every year. According to the technology used about 1500 m3 of adjacent stratum is dumped at the surface per every 1000 tons of coal mined. Apart from land amortization, waste dumps drastically change the natural landscape and pollute air, soil and water sources as the result of water and wind erosion, as well as self-ignition processes. A serious concern exists with respect to the Western Donbass coal mining region in Ukraine, where the coal extraction is made by the subsurface way and solid wastes are represented by both spoil dumps and wastes after coal processing. Sulphides, mostly pyrite (up to 4% of waste material), are widely distributed in the waste heaps freshly removed due to coal mining in Western Donbass.The oxidation of pyrite with the presence of oxygen and water is accompanied by a sharp drop in the pH from the surface layer to the spoil dumps(from 5.2-6.2 to 3.9-4.2 in soil substrates with chernozen and from 8.3-8.4 to 6.7-7.2 in soil substrates with red-brown clay, stabilizing in dump material in both cases at 2.9-3.2). Low pH generates the transformation of a number of toxic metals and other elementspresent in waste rock (e.g. Fe, Al, Mn, Zn, Mo, Co, As, Cd, Bi, Pb, U) into mobile forms. To stabilize and reduce metal mobility the most resistant plants that occur naturally in specified ecosystems can be used. On coal spoil dumpsin Western Donbas the dominant species are Bromopsis inermis, subdominant Artemisia austriaca; widespread are also Festucas pp., Lathyrus tuberosus, Inula sp., Calamagrostis epigeios, Lotus ucrainicus, and Vicias pp. Identification of plants tolerant to target metals is a key issue in phytotechnology for soil restoration. It is hypothesized that naturally occurring plants growing on coal spoil dumps can be candidates for phytostabilization, phytoextraction (phytoaccumulation) and phytomining

  3. Vegetational stabilization of uranium spoil areas, grants, New Mexico

    International Nuclear Information System (INIS)

    Kelley, N.E.

    1979-01-01

    Factors that could be detrimental to vegetative stabilization of uranium mine and mill waste material were examined. Physical and chemical analyses of materials from an open-pit uranium mine and material from three inactive mill tailing piles in New Mexico were performed. Analyses for selected trace elements in mill tailing material and associated vegetation from piles in New Mexico, Colorado, and Utah were also performed. Field and laboratory experiments identified problems associated with establishing vegetation on spoil material. Problems of uptake and concentration of toxic elements by plants growing on specific spoil material were also identified. Ecological observations in conjunction with physical and chemical analyses of specific geologic units, which form the overburden and waste dumps at the open-pit mine, identified a specific geologic material that, if segregated and placed on the surface of the dumps, would pose the least set of problems for a revegetation program. A pilot revegetation project verified that segregation and use of specific geologic material in the overburden could be utilized successfully and economically for reestablishment of native vegetation on mine waste material

  4. Final strip mine regs released

    Energy Technology Data Exchange (ETDEWEB)

    1977-12-12

    The final interim surface mining regulations were published by the Office of Surface Mining on 12 December. Among the requirements are that the operation should minimize disturbances to the prevailing hydrological balance in order to prevent long-term adverse changes in water quality and quantity, in the depth of ground water and in the location of surface water drainage channels. Regulations for sedimentation ponds are retained but exemption may be granted to allow the pH to rise above 9 if manganese levels (4 mg/l) cannot be met. The 24-hour frequency event for which effluent limitations must be applied has been reduced from 25 years to 10 years. Large sedimentation ponds must be constructed to withstand, at a minimum, a 100-year frequency, 6-hour duration storm. The regulations are to take effect on the 3rd of May 1978.

  5. Race, Commitment to Deviance, and Spoiled Identity

    Science.gov (United States)

    Harris, Anthony R.

    1976-01-01

    Data generated by 234 young black and white inmates in 1971 challenge the assumption that spoiled identity is a necessary, socially invariant outcome of deviant commitment and self-definition. For blacks, the relationship between criminal self-typing and stability and esteem is negative but inconsequential; for whites, the relationship is negative…

  6. A Spectral Emissivity Library of Spoil Substrates

    Czech Academy of Sciences Publication Activity Database

    Pivovarník, Marek; Pikl, Miroslav; Frouz, J.; Zemek, František; Kopačková, V.; Notesco, G.; Ben Dor, E.

    2016-01-01

    Roč. 1, č. 2 (2016) E-ISSN 2306-5729 R&D Projects: GA MŠk(CZ) LO1415 Institutional support: RVO:86652079 Keywords : post-mining sites * spectral emissivity * spectral library * spoil substrates Subject RIV: EH - Ecology, Behaviour OBOR OECD: Environmental sciences (social aspects to be 5.7)

  7. Revegetation of Alaskan coal mine spoils. Progress report

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell, W W; Mitchell, G A; McKendrick, J D

    1980-05-23

    Activities initiated after the start of the revegetation project on Alaskan coal mine spoils on September 1, 1979 have consisted mainly of some fall plantings (dormant seedings) and soil and coal spoil samplings and analyses. Because of the late summer start for the project, only a limited amount of field work could be initiated in plant material studies. This consisted of a fall planting at the Usibelli mine site at Healy in interior Alaska. The planting was intended to test the efficacy of seeding in the frost period following the growing season, requiring the seed to remain dormant over winter and to germinate when conditions become favorable in late spring. It also was intended as a comparison of a number of different grasses. Thirty entries were seeded in three replications. Fifteen species of grasses and a clover were included in the trial. The site provided for the trial was on overburden material along a streambed. Among the entries were eight cultivars of introduced grasses, five cultivars of native Alaskan germplasm, one introduced clover cultivar, and sixteen experimental grasses mainly of Alaskan origin.

  8. 30 CFR 816.71 - Disposal of excess spoil: General requirements.

    Science.gov (United States)

    2010-07-01

    ... does not slake in water or degrade to soil material, and which is free of coal, clay or other... of the soil. (2) Excess spoil shall be transported and placed in a controlled manner in horizontal... outslope of the fill if required for stability, control of erosion, to conserve soil moisture, or to...

  9. 30 CFR 817.71 - Disposal of excess spoil: General requirements.

    Science.gov (United States)

    2010-07-01

    ... does not slake in water or degrade to soil materials, and which is free of coal, clay or other... of the soil. (2) Excess spoil shall be transported and placed in a controlled manner in horizontal... outslope of the fill if required for stability, control of erosion, to conserve soil moisture, or to...

  10. Spoil characteristics and vegetation development of an age series of mine spoils in a dry tropical environment

    Energy Technology Data Exchange (ETDEWEB)

    Jha, A K; Singh, J S [Banaras Hindu University, Varanasi (India). Dept. of Botany

    1991-12-01

    A series of coal mine spoils (5,10,12,16 and 20-yr old) in a dry tropical environment was sampled to assess the changes with time in spoil characteristics, species composition and plant biomass. Coarse fragments ({gt} 2 mm) decreased with age of mine spoil while the proportion of 0.2-0.1 mm particles increased. Total soil N, mineral N, NaHCO{sub 3}-extractable P, and exchangeable K increased with age of mine spoil and these parameters were lower in mine spoils than native forest soil even after 20 years of succession. Exchangeable Na decreased with age of mine spoil and in 20-yr old spoil it was higher than native forest soil. Plant community composition changed with age. Only a few species participated in community formation. Species richness increased with age, while evenness and species diversity declined from 5-yr old to 16-yr old community with an increase in the 20-yr old community. A reverse trend occurred for concentration of dominance. Area-weighted shoot and root biomass of other species increased with the age of the mine spoil while that of Xanthium strumarium patches declined with age. Data collection on spoil features, microbial C, N and P,and shoot and root biomass when subjected to Discriminant Analysis indicated a continued profound effect of age. 10 and 12-yr old mine spoils were closer to each other and 5 and 20-yr old spoils were farthest apart.

  11. Spoil characteristics and vegetation development of an age series of mine spoils in a dry tropical environment

    International Nuclear Information System (INIS)

    Jha, A.K.; Singh, J.S.

    1991-01-01

    A series of coal mine spoils (5,10,12,16 and 20-yr old) in a dry tropical environment was sampled to assess the changes with time in spoil characteristics, species composition and plant biomass. Coarse fragments (> 2 mm) decreased with age of mine spoil while the proportion of 0.2-0.1 mm particles increased. Total soil N, mineral N, NaHCO 3 -extractable P, and exchangeable K increased with age of mine spoil and these parameters were lower in mine spoils than native forest soil even after 20 years of succession. Exchangeable Na decreased with age of mine spoil and in 20-yr old spoil it was higher than native forest soil. Plant community composition changed with age. Only a few species participated in community formation. Species richness increased with age, while evenness and species diversity declined from 5-yr old to 16-yr old community with an increase in the 20-yr old community. A reverse trend occurred for concentration of dominance. Area-weighted shoot and root biomass of other species increased with the age of the mine spoil while that of Xanthium strumarium patches declined with age. Data collection on spoil features, microbial C, N and P,and shoot and root biomass when subjected to Discriminant Analysis indicated a continued profound effect of age. 10 and 12-yr old mine spoils were closer to each other and 5 and 20-yr old spoils were farthest apart

  12. Spoil dump design and rehabilitation management practices (Australia)

    International Nuclear Information System (INIS)

    Goh, E.K.H.; Aspinall, T.O.; Kuszmaul, J.S.

    1998-01-01

    The environmental impact of mining and evolving environmental legislation has been receiving increased attention worldwide in the last two decades. The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental legislative agencies and members of the public. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. There is thus the need to increase the base of knowledge on the existing practices of spoil dump design and rehabilitation. Information concluded from the analysis of the industrial survey carried out on Australian spoil dump management practices at coal, gold and ore mines are presented in this paper. The questionnaire asked for details of soil type of spoils, and factors influencing the design of spoil dumps (climate, rate of erosion, height of dumps, slope gradient and length, overburden handling equipment, soil characteristics, legislation and wastes). 10 refs., 5 figs., 5 tabs

  13. New possibilities for slope stability assessment of spoil banks

    Energy Technology Data Exchange (ETDEWEB)

    Radl, A [Palivovy Kombinat, Vresova (Czechoslovakia)

    1991-03-01

    Discusses problems associated with slope stability of spoil banks consisting of sedimentary rocks from brown coal surface mining. Effects of rock physical properties on slope stability are analyzed: grain size distribution, compression strength, moisture content, angle of internal friction, etc. Mechanism of plastic slope deformation which occurs during a landslide is evaluated. Formulae for calculating slope stability considering stress distribution in a spoil bank (including all the main factors that influence stresses) are derived. Practical use of the gamma-gamma logging and logging schemes used in geodetic surveys of unstable spoil banks in Czechoslovakia (the Vintirov spoil bank in the Sokolov brown coal district) are discussed. 5 refs.

  14. Spoil pile instabilities with reference to a strip coal mine in Turkey: mechanisms and assessment of deformations

    Science.gov (United States)

    Kasmer, Ozgu; Ulusay, Resat; Gokceoglu, Candan

    2006-02-01

    With the increasing adoption of the surface mining of coal, problems associated with spoil pile instability, which affects resource recovery, mining cost, and safety and presents environmental hazards, have become a matter of prime concern to mine planners and operators. The study of geotechnical aspects is thus very important in the rational planning for the disposal, reclamation, treatment and utilization of spoil material. A strip coal mine, one of the largest open pit mines in Turkey, is located in Central Anatolia and provides coal to a thermal power station. Coal production is carried out in two adjacent open pits, the Central Pit and South Pit. A large-scale spoil pile instability over an area of 0.3 km2 occurred within the dumping area of the Central pit. In addition, small-scale movement occurred in the outside dumping area. This paper outlines the results of field and laboratory investigations to describe the mechanisms of the spoil pile instabilities and to assess deformations monitored over a long period following the failure. Shear test results indicate that the interface between the floor and spoil material dumped by dragline has a negligible cohesion and is the most critical plane of weakness for spoil pile instability. Back analyses based on the method of limit equilibrium and the numerical modelling technique, and observations in the pit revealed that failure occurred along a combined sliding surface consisting of a circular surface through the spoil material itself and a planar surface passing along the interface between the spoil piles and floor. The analyses also indicated that pore water pressure ratios of about 0.25 satisfy limiting equilibrium condition and that rainfall about one month before the failure may be a contributing factor to the instability. Movement monitoring data obtained following the failure over a 1.5-year period suggested that the ongoing deformations were mainly due to compaction of the spoil material. Based on the

  15. Stabilization of metals in acidic mine spoil with amendments and red fescue (Festuca rubra L.) growth.

    Science.gov (United States)

    Simon, László

    2005-12-01

    Stabilization of metals with amendments and red fescue (Festuca rubra, cv. Keszthelyi 2) growth was studied on an acidic and phytotoxic mine spoil (pH(KCl) 3.20-3.26; Cd 7.1 mg kg(-1), Cu 120 mg kg(-1), Pb 2154 mg kg(-1) and Zn 605 mg kg(-1)) from Gyöngyösoroszi, Hungary in a pot experiment. Raising the pH above 5.0 by lime (CaCO(3)), and supplementing with 40 mg kg(-1)nitrogen (NH(4)NO(3)) made this material suitable for plant growth. All cultures were limed with 0.5% (m/m) CaCO(3) (treatment 1), which was combined with 5% (m/m) municipal sewage sludge compost (treatment 2), 5% (m/m) peat (treatment 3), 7.5% (m/m) natural zeolite (clinoptilolite) (treatment 4), and 0.5 (m/m) KH(2)PO(4) (treatment 5). Treatments 1-5 were combined with each other (treatment 6). After 60 days of red fescue growth, pH of the limed mine spoil decreased in all cultures units. Application of peat caused the highest pH decrease (1.15), while decrease of pH was less than 0.23 in treatments 2, 5 or 6. Application of lime significantly reduced concentrations of metals in the 'plant available' fraction of mine spoil compared to non-limed mine spoil. Amendments added to limed mine spoil changed variously the ratio of Cd, Cu, Pb and Zn in exchangeable or 'plant available' fractions, differently influencing the phytoavailability of these metals. Most of the metals were captured in the roots of test plants. Treatment 2 caused the appearance of less Cd in shoots (spoil, however the application of 0.5 phosphate was less favourable. Liming, application of amendments and growth of red fescue can stabilize metals in acidic and phytotoxic mine spoil, and by phytostabilization they can reduce the risk of metal contamination of the food chain.

  16. Selenium transformation in coal mine spoils: Its environmental impact assessment

    Energy Technology Data Exchange (ETDEWEB)

    Harness, J.; Atalay, A.; Koll, K.J.; Zhang, H.; Maggon, D.

    1991-12-31

    The objective of this program was to conduct an environmental impact assessment study for selenium from coal mine spoils. The use of in-situ lysimetry to predict selenium speciation, transformation, and mobility under natural conditions was evaluated. The scope of the study was to construct and test field-scale lysimeter and laboratory mini-column to assess mobility and speciation of selenium in coal mine overburden and soil systems; to conduct soil and groundwater sampling throughout the state of Oklahoma for an overall environmental impact assessment of selenium; and to conduct an in-depth literature review on the solubility, speciation, mobility, and toxicity of selenium from various sources. Groundwater and surface soil samples were also collected from each county in Oklahoma. Data collected from the lysimeter study indicated that selenium in the overburden of the abandoned mine site was mainly found in the selenite form. The amount of selenite found was too low and immobile to be of concern to the environment. The spoil had equilibrated long enough (over 50 years) that most of the soluble forms of selenium have already been lost. Examination of the overburden indicated the presence of pyrite crystals that precipitated over time. The laboratory mini-column study indicated that selenite is quite immobile and remained on the overburden material even after leaching with dilute acid. Data from groundwater samples indicated that based on the current permissible level for selenium in groundwater (0.01 mg Se/L), Oklahoma groundwater is widely contaminated with the element. However, according to the new regulation (0.05 mg Se/L), which is to be promulgated in 1992, only 9 of the 77 counties in the state exceed the limit.

  17. Extraterrestrial materials processing and construction

    Science.gov (United States)

    Criswell, D. R.

    1978-01-01

    Applications of available terrestrial skills to the gathering of lunar materials and the processing of raw lunar materials into industrial feed stock were investigated. The literature on lunar soils and rocks was reviewed and the chemical processes by which major oxides and chemical elements can be extracted were identified. The gathering of lunar soil by means of excavation equipment was studied in terms of terrestrial experience with strip mining operations on earth. The application of electrostatic benefication techniques was examined for use on the moon to minimize the quantity of materials requiring surface transport and to optimize the stream of raw materials to be transported off the moon for subsequent industrial use.

  18. Asfordby spoiled - remote disposal of spoil - the case of Asfordby mine in Leicestershire

    Energy Technology Data Exchange (ETDEWEB)

    Rose, D

    1988-03-01

    The Asfordby Mine Project in Leicestershire, UK is scheduled for completion in 1993/4 and should produce 3 mt of coal pa. An estimated 650 000 tpa of spoil would be generated, 10% of which could be used for backfilling elsewhere in the area. The creation of spoil heaps on site was rejected by the County Council on environmental and agricultural grounds, and remote disposal was investigated by a Working Party. Four remote sites were identified, having disposal costs varying from 3.82 to 11.34 UKL per tonne (compared with 2.10 UKL on site). A pilot remote disposal scheme involving two old clay pits was explored, but the costs were found to outweigh the other advantages and so the idea has been dropped. Appeals have been made to the Department of the Environment to reconsider the advantages of such an innovative approach and to seek funding for it from the site operator and the EEC.

  19. Recognizing critical mine spoil health characteristics to design ...

    Science.gov (United States)

    Biochar can be used as an amendment to remediate metal-contaminated mine spoils for improved site phytostabilization. For successful phytostabilization to occur, biochar amendments must improve mine spoil health with respect to plant rooting plus uptake of water and nutrients. An inappropriate biochar may negatively impact plant growth conditions resulting in poor plant establishment and growth. Matching the appropriate biochar for each mine site requires reconnaissance of spoil chemical and physical conditions and then identifying which properties need rectified to promote plant growth. A rectification hierarchy needs to be established with the primary limiting factor being addressed first, then successive limitations addressed simultaneously or thereafter. We posit that spoils at each site will have a unique chemical, physical, and biological signature that will affect plant growth. For example, some spoils may be extremely acidic, possess phytotoxic concentrations of heavy metals, or have physical conditions that limits water storage and root penetration. Quantifying these and other conditions beforehand allows for the production of designer biochar with specific characteristics tailored for specific plant growth deficiencies within each spoil. Additionally, we recommend the use of proximally located, undisturbed soils to establish spoil remediation targets. In our work, we have developed a decision-tree flow-chart that identifies salient chemical,

  20. Use of colliery spoil in public works. La utilizacion de esteriles de la mineria del carbon en obras publicas

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez Canibano, J.; Rodriguez Ortiz, J.M. (HUNOSA, Oviedo (Spain))

    Colliery spoil presents a number of problems with regard to its storage because of the high cost involved, the difficulty of finding suitable land and its integration into the landscape. These factors are also affected by environmental legislation. One of the most interesting applications for colliery dirt is in the field of public works for in-filling operations, embankments, road building, dikes, etc., applications which require huge quantities of material without it needing to be processed. This article describes the physical and mechanical properties of colliery spoil from the point of view of its use in public works. 14 refs., 17 figs., 3 tabs.

  1. Guide for calculating the stability of mine berms and spoil bank slopes in the Maritsa-Iztok coal basin

    Energy Technology Data Exchange (ETDEWEB)

    Georgiev, G; Todorova, M; Doneva, V; Novachkov, N; Nedyalkov, N; Mitev, A; Rachev, R

    1984-08-01

    Major landslides are described which occurred in the basin between 1963 and 1970 during overburden removal and formation of spoil banks. Guidelines for the prevention of landslides were developed on the basis of large scale studies of geomechanics, geostatic calculations and geodetic observations of slope behavior; no further landslide has occurred since 1970. Cohesion coefficients, angle of internal friction and shear properties were determined for each material occurring in the clayey and sandy overburden and for the coal (ash content 15-55%). Slope stability of working benches and spoil banks at the Troyanovo mines was then calculated. 8 references.

  2. The flow properties of colliery spoil rockpaste as used in the infilling of abandoned mine workings

    Energy Technology Data Exchange (ETDEWEB)

    Ghataora, G.S.; Jarvis, S.T. [University of Birmingham, Birmingham (United Kingdom)

    1998-07-01

    Colliery spoil is the major constituent of colliery spoil 'rockpaste' which has been used to infill abandoned limestone mines in the West Midlands of England since the early 1980s. The other constituents of rockpaste are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes on to consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising infilling a 6600 m{sup 3} section of an abandoned mine was conducted prior to the infilling of the Littleton Street Mine which had a volume of about 500 000 m{sup 3}. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. 5 refs., 16 figs., 1 tab., 1 plate.

  3. Dredge spoil disposal off Kavaratti Island, Lakshadweep, India

    Digital Repository Service at National Institute of Oceanography (India)

    Chandramohan, P.; SanilKumar, V.; Jayakumar, S.

    Maintenance dredging has been carried out along the navigational channel at Kavaratii Island and dredge spoil is disposed in the open sea. This paper describes the movement of sediment plume while dredging and disposal. The study indicates...

  4. Stabilization of dredged spoils for pavement construction in the ...

    African Journals Online (AJOL)

    Natural soils underlying the East-West road are mainly clay and silt of poor quality ... on the dredged soils included particle size distribution, compaction and California Bearing Ratio. Cement stabilization was performed on the dredged spoil.

  5. stabilization of dredged spoils for pavement construction in the niger

    African Journals Online (AJOL)

    Dr. Tse

    Natural soils underlying the East-West road are mainly clay and silt of poor quality ... on the dredged soils included particle size distribution, compaction and California ... KEYWORDS: Stabilization, dredge spoil, pavement, Niger Delta, cement.

  6. Biological reclamation of coal mine spoils without topsoil: an amendment study with domestic raw sewage and grass-legume mixture

    Energy Technology Data Exchange (ETDEWEB)

    Maiti, S.K.; Saxena, N.C. [Indian School of Mines, Dhanbad (India). Centre of Mining Environment

    1997-12-31

    A range of tree species were successfully established and grown on spoil site irrigated with domestic raw sewage in India. The heavy metals content in leaves, stem wood, stem bark root wood and root bark differ between species. In general, heavy metals like Fe, Zn, Mn, Cu, and Pb were accumulated more in Eucalyptus then Melia, however only Co accumulated maximum in Acacia. Increase trend was reported in respect of Na, K, Fe, Zn, Cu in grass and vegetables which were grown at a sewage fed farm. However, in all the cases micronutrients and heavy metals contents did not reach the critical limits to produce any phytotoxic effect. Irrigation with raw sewage had no adverse effect on chemical properties of spoil over the 3 year period. This study shows that raising vegetation on spoil material in mining areas irrigated with raw sewage is feasible. However, irrigation by raw sewage caused the accumulation of heavy metals in different plant parts. These plants are not of the fodder type and thus are not entering directly into ecological food chains, hence they can act as heavy metals sinks. On the basis of the Grass-legume experimental study, it may be concluded that N accumulation of coal mine spoil related with nature of spoil, prevailing climate and legume used. In a tropical climate N accumulation rate was found higher than in a temperate one. Addition of phosphorus fertilizer is essential for the reclamation of many mine spoils because even after three years available P level can remain deficient. Available K was found to be sufficient after three years.

  7. Phytoextraction from mine spoils: insights from New Caledonia.

    Science.gov (United States)

    Losfeld, Guillaume; Mathieu, Romain; L'Huillier, Laurent; Fogliani, Bruno; Jaffré, Tanguy; Grison, Claude

    2015-04-01

    Increasing pressure on mineral resources has drawn research efforts into innovative supply and recycling. Metal-rich biomass produced in phytoextraction recently proved an interesting starting material for green chemistry. It allows the production of new catalysts, referred to as ecocatalysts. Ecocatalysts provide increased yields in chemical production and increased regio- and chemo-selectivity, which result in high added value. This new approach to using metal-rich biomass could spur the development of phytoextraction, a technique considered promising for long, yet without credible economic outlets. In this regard, metallophyte biodiversity hotspots, such as New Caledonia, are of particular interest for biomass supply. Potential phytoextraction from mine spoils using two species endemic to New Caledonia is discussed here. Geissois pruinosa, a hypernickelophore, and Grevillea exul, a Mn accumulator, were selected for these original experiments. The results presented here 20 months after plantation of young trees from a nursery show the interest of the approach. Mean Ni concentrations of up to 1513 mg kg(-1) are reported in G. pruinosa, as well as 2000 mg kg(-1) Mn in G. exul. Concentrations of Ni and Mn in the leaves of each species appear to be correlated with leaf age. Plantation of these species may also ensure mine reclamation, and experiments were conducted with the principles of ecological restoration in mind adding a further dimension to the approach.

  8. Reclamation of coal mine spoil dump through integrated biotechnological approach

    International Nuclear Information System (INIS)

    Juwarkar, A.S.; Thawale, P.R.; Mowade, S.; Shrivastava, S.; Deshbhratar, P.B.; Juwarkar, A.

    1994-01-01

    Laboratory and field studies were carried out to restore the fertility and productivity of coal mine spoil using primary clarifier sludge from paper mill effluent treatment plant and use of specialised culture of biofertilizers and mycorrhizal fungi. Plants namely Tectona grandis, Delbergia sissoo, Gmelina arporea, Emblica officinalis and Cassia seamea were grown. Sludge amendment enhanced the survival rate of plants to 80% compared to 20% in unamended spoil. Plants grown on unamended spoil showed stunted growth. Growth of plants increased by 188-484% when sludge was applied at the rate of 100 tonnes per hectare. At 100 tones per hectare sludge amendment, biofertilizer and mycorrhizae treatment there were 83.7 nodules in shishum as against only 4.6 nodules in case of spoil alone. Further root length was 276% and 281% more respectively in case of shishum and teak. Inoculation of plant saplings with respective biofertilizers and mycorrhizae further increased the plant growth by 144-198%. At Durgapur coal mine, 56,000 saplings of Tectona grandis, Gmelina arporea, Delbergia sissoo, Emblica officinalis, Azadirachta indica, Acacia ariculiformis, Prosopis etc were successfully planted on spoil dump using integrated biotechnological approach. 10 refs., 5 tabs

  9. Hydrogeology and ground-water-quality conditions at the Linn County landfill, eastern Kansas, 1988-89

    International Nuclear Information System (INIS)

    Falwell, R.; Bigsby, P.R.; Myers, N.C.

    1991-01-01

    An investigation of the hydrogeology and groundwater quality conditions near the Linn County Landfill, eastern Kansas was conducted from July 1988 through June 1989. The landfill is located in an unreclaimed coal strip-mine area near Prescott. Analysis of water levels from nine temporary wells and from strip-mine ponds indicated that groundwater flows southwest through the present landfill. A county road west of the landfill acts as a barrier to shallow westerly groundwater flow. Seasonal variations in the direction of groundwater flow may occur. Water samples from monitoring wells and a strip-mine pond were analyzed for inorganic and organic compounds. Iron, manganese, and dissolved-organic-carbon concentrations were good indicators of the presence of landfill leachate in the groundwater. Benzene, carbon tetrachloride, 1,1-dichloroethane, and 1,1,1-trichloroethane were also detected. None of the inorganic or organic compounds detected exceeded Kansas primary drinking-water standards. Chemical concentrations and water levels in some nested wells indicate there is a hydraulic connection between the strip-mine spoil material and the underlying limestone. Leachate-contaminated groundwater has the potential to migrate southwest corner of the landfill through either strip-mine spoil material or through the underlying Pawnee Limestone

  10. Revegetation of metalliferous mine spoil contaminated by lead and zinc

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, M S; McNeilly, T; Putwain, P D

    1977-04-01

    Plant growth and development on metalliferous mine spoil is restricted by the high concentrations of phytotoxic metals and by the low levels of macronutrients in the substrates. Swards established on innocuous amendments applied to the surface of mine spoil deteriorate when roots penetrate to the underlying toxic substratum. This deterioration is attributed to the accumulation of toxic metals. The rate of decline is determined by the inherent fertility of the amendment and the depth to which it is applied. Results of field trials on calcareous and acidic lead/zinc spoils indicate that inert amendments may be more suitable where revegetation is for amenity or recreational purposes. Legumes are essential components of low-maintenance swards established on substrates of low nutrient status.

  11. 30 CFR 816.73 - Disposal of excess spoil: Durable rock fills.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Disposal of excess spoil: Durable rock fills...-SURFACE MINING ACTIVITIES § 816.73 Disposal of excess spoil: Durable rock fills. The regulatory authority may approve the alternative method of disposal of excess durable rock spoil by gravity placement in...

  12. 30 CFR 817.73 - Disposal of excess spoil: Durable rock fills.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Disposal of excess spoil: Durable rock fills...-UNDERGROUND MINING ACTIVITIES § 817.73 Disposal of excess spoil: Durable rock fills. The regulatory authority may approve the alternative method of disposal of excess durable rock spoil by gravity placement in...

  13. Investigation on the spoiling of meat using PTR-MS

    International Nuclear Information System (INIS)

    Mayr, D.; Maerk, T.D.; Margesin, R.; Schinner, F.

    2002-01-01

    The spoiling of meat was investigated. Beef (pork) were wrapped into different kinds of packages (air and vacuum) and stored at 4 o C for 10 (13) days. The emitted volatile organic compounds (VOCs) in the course of time were measured and a large increase in these emissions after a few days of storage was found. Also a large difference in the spoiling behavior between vacuum- and air- packed meat was observed. The measurements were performed using a proton-transfer-reaction-mass spectrometer(PTR-MS) system, it allows on-line monitoring of volatile organic compounds (VOCs) concentrations. Ethylacetate, methylpropionate, and propylformate were detected as typical spoiling compounds in pork samples. After 3.5 days the concentrations started to exponentially increase, but after 6 days remained more or less unchanged. This VOCs behaviour corresponds to a typical bacterial growth curve. Therefore, it was concluded that bacteria produce these components. In a second measurements set, the VOCs emitted by beef under aerobic (normal packed) and anaerobic (vacuum packed) conditions were compared. In the case of normal air-packed beef, the above mentioned spoiling compounds strongly increased with the time, while with the vacuum-packed beef a strong increase of ethanol was detected. This method as a replacement of the bacteriological examinations of meat spoilage is proposed. (nevyjel)

  14. An appraisal of the potential use of fly ash for reclaiming coal mine spoil.

    Science.gov (United States)

    Ram, Lal C; Masto, Reginald E

    2010-01-01

    Growing dependence on coal-fired power plants for electrical generation in many countries presents ongoing environmental challenges. Burning pulverized coal in thermal power plants (TPPs) generates large amounts of fly ash (FA) that must be disposed of or otherwise handled, in an environmentally-sound manner. A possible option for dealing with fly ash is to use it as an amendment for mine spoil or other damaged soil. It has been demonstrated through studies in India and other countries that FA alone or in combination with organic or inorganic materials can be used in a productive manner for reclamation of mine spoil. The characteristics of FA, including silt-sized particles, lighter materials with low bulk density (BD), higher water holding capacity, favorable pH and significant concentrations of many essential plant nutrients, make it a potentially favorable amendment for mine spoil reclamation. Studies have indicated that the application of FA has improved the physical, chemical and biological qualities of soil to which it is applied. The release of trace metals and soluble salts from FA could be a major limitation to its application. This is particularly true of fresh, un-weathered FA or acidic FA, although perhaps not a concern for weathered/pond ash or alkaline FA. Some potential contaminants, especially metals and other salt ions, could be immobilized and rendered biologically inert by the addition of certain inorganic and organic amendments. However, in view of the variability in the characteristics of FAs that are associated with location, feed coal, combustion conditions and other factors, the suitability of a particular FA for a specific soil/mine spoil needs to be critically evaluated before it is applied in order to maximize favorable results and eliminate unexpected consequences. FA generated in India tends to be mostly alkaline, with lower levels of trace elements than are often found in FAs from other countries. The concentrations of potential

  15. Symbiont effect of Rhizobium bacteria and vesicular arbuscular mycorrhizal fungi on Pisum sativum in recultivated mine spoils

    Energy Technology Data Exchange (ETDEWEB)

    Biro, B.; Voros, I.; Kovespechy, K.; Szegi, J. (Hungarian Academy of Sciences, Budapest (Hungary). Soil Science and Agricultural Chemistry Research Institute)

    The frequency (F%) of spontaneous endomycorrhizal fungal infection (AMF) and the root modulation of Pisum sativum L, was studied after 8 and 15 years of recultivation in 4 soils (andesitic tuff yellow sand, yellow clay, and grey clay) disturbed by mining activities. The effects of Rhizobium inoculation and the interaction of both microsymbionts with plant production were also examined along with humus content and the humus stability coefficient, in the following variations: control, NPK fertilizer, NPK+lignite, NPK+straw and sewage sludge. Dump spoils originating from deep geological layers were poor in organic materials. After 12 years of recultivation, the humus content increased significantly. No such increase was noted in grey clay and the natural, brown forest soil used as an undisturbed (control) sample. The degradation of soils by mining brings about a decrease in the rhizobial and mycorrhizal population, so the number of spontaneous Rhizobium nodules is relatively low and does not influence the yield of peas. Inoculation with a selected effective strain of Rhizobium leguminosarum bv. viceae, however, enhanced dry matter production in these microbiologically degraded soils. Although the frequency of AMF infection was also higher after rhizobial inoculation, no positive correlation was found between dry matter production of peas and the F% of AMF. Spoils treated with lignite, straw, and sewage sludge had an especially high level of spontaneous mycorrhizal populations, indicating that organic materials had a favorable effect on the recultivation processes and fertility of mine spoils.

  16. Prediction of the acid generating potential of coal mining spoils

    International Nuclear Information System (INIS)

    Monterroso, C.; Macias, F.

    1998-01-01

    The sulfide oxidation impact on mined land reclamation makes it necessary for mine spoils to be classified according to their acidifying potential. In this paper predictions were made of the acid generating potential of sulfide-containing spoils from the Puentes lignite mine (Galicia, NW Spain), and the limits of sulfur contents allowable for their storage in aerobic conditions, were established. Using samples of fresh spoils, analyses were made of the content and speciation of sulfur, pH was measured after oxidation of the sample with H 2 O 2 (pH of oxidation = pH OX ), and titration of the oxidation extract with 0.1N NaOH to pH = 7 was carried out (Net Acid Production = NAP). The total sulfur content (S T ) varied between 3%, with pyritic-S being the most common form (> 80%). pH OX varied between 1.6 and 6.4 and NAP between 1.2 and 85.0 Kg-CaCO 3 t -1 . A high correlation was found between the NAP and the S T (r-0.98, p T > 0.15% cause high risks of mine-soil acidification, and create the need for large doses of CaCO 3 to be used on final surface of the mine dump. Use of fly ash, produced from the combustion of lignite, as an alternative to commercial lime is more effective in the control of acidity generated by spoils with high S T . 20 refs., 5 figs., 1 tab

  17. Depletion-Mode GaN HEMT Q-Spoil Switches for MRI Coils.

    Science.gov (United States)

    Lu, Jonathan Y; Grafendorfer, Thomas; Zhang, Tao; Vasanawala, Shreyas; Robb, Fraser; Pauly, John M; Scott, Greig C

    2016-12-01

    Q-spoiling is the process of decoupling an MRI receive coil to protect the equipment and patient. Conventionally, Q-spoiling is performed using a PIN diode switch that draws significant current. In this work, a Q-spoiling technique using a depletion-mode Gallium Nitride HEMT device was developed for coil detuning at both 1.5 T and 3 T MRI. The circuits with conventional PIN diode Q-spoiling and the GaN HEMT device were implemented on surface coils. SNR was measured and compared for all surfaces coils. At both 1.5 T and 3 T, comparable SNR was achieved for all coils with the proposed technique and conventional Q-spoiling. The GaN HEMT device has significantly reduced the required power for Q-spoiling. The GaN HEMT device also provides useful safety features by detuning the coil when unpowered.

  18. Reclamation of colliery mine spoil founded on natural succession

    International Nuclear Information System (INIS)

    Jochimsen, M.E.A.

    1996-01-01

    Reclamation of derelict land is of great concern for industrial countries. Technically produced and biologically inactive soils are said to be hostile to plants. Therefore, great effort is applied, in order to reintegrate them into the landscape. Ordinarily plant settlement starts with pioneer plants, especially herbs. Reafforestation, in this case, is an ecological misunderstanding. A method of mimicking natural succession including its ecological and economic advantages is described. The results of an applied experiment on virgin mine spoil with respect to species number, plant cover degree, and above ground phytomass production in the course of six years are reported in this paper. 12 refs., 4 figs

  19. Environmental risk evaluation of the use of mine spoils and treated sewage sludge in the ecological restoration of limestone quarries

    Science.gov (United States)

    Jordán, M. M.; Pina, S.; García-Orenes, F.; Almendro-Candel, M. B.; García-Sánchez, E.

    2008-07-01

    The ecologic restoration criteria in areas degraded from extraction activities require making use of their mine spoils. These materials do not meet fertility conditions to guarantee restoration success and therefore, need the incorporation of organic amendments to obtain efficient substratum. Reducing the deficiencies in the organic material and restoration material nutrients with the contribution of treated sewage sludge is proposed in this work. This experiment was based on a controlled study using columns. The work was conducted with two mine spoils, both very rich in calcium carbonate. The first mineral, of poor quality, came from the formation of aggregates of crushed limestone ( Z). The other residual material examined originated in limestone extraction, formed by the levels of interspersed non-limestone materials and the remains of stripped soils ( D). Two treatments were undertaken (30,000 and 90,000 kg/ha of sewage sludge), in addition to a control treatment. The water contribution was carried out with a device that simulated either short-duration rain or a flooding irrigation system in order to cover the surface and then percolate through the soil. The collection of leached water took place 24 h after the applications. Different parameters of the leached water were determined, including pH, electrical conductivity, nitrate anions, ammonium, phosphates, sulphates and chlorides. The values obtained for each irrigation application are discussed, and the nitrate values obtained were very elevated.

  20. Reestablishing natural succession on acidic mine spoils at high elevations: long-term ecological restoration

    Science.gov (United States)

    Ray W. Brown; Michael C. Amacher; Walter F. Mueggler; Janice Kotuby-Amacher

    2003-01-01

    Methods for restoring native plant communities on acidic mine spoils at high elevations were evaluated in a "demonstration area" in the New World Mining District of southern Montana. Research plots installed in 1976 were assessed for 22 years and compared with adjacent native reference plant communities. A 1.5-acre (0.61-ha) area of mine spoils was shaped and...

  1. Initial vesicular-arbuscular mycorrhizal development of slender wheatgrass on two amended mine spoils

    Energy Technology Data Exchange (ETDEWEB)

    Zak, J.C.; Parkinson, D. (University of Calgary, Calgary, AB (Canada). Dept. of Biology)

    1982-01-01

    The initial vesicular-arbuscular (VA) mycorrhizal development of slender wheatgrass on extracted oil-sands and subalpine coal-mine spoils, amended with either fertilizer, peat, or liquid sewage sludge, was examined. Plants were sampled at 2,6 and 10 weeks after plant emergence and the level of infection was expressed as length of mycorrhizal root per plant and length of root which contained arbuscules, vesicles, or only hyphae. Mycorrhizal infection of slender wheatgrass on the oil sands was limited to plants on the peat-amended spoil. Infection of plants on the peat-amended oil-sands spoil was detected by 2 weeks. Plants on the subalpine spoil were infected at 2 weeks only on the peat-amended spoil. While slender wheatgrass on the control and fertilizer-amended spoil developed mycorrhizae by 6 weeks, infection was not observed in plants on the sewage-amended spoil until 10 weeks. At 10 weeks, there were no significant differences in lengths of mycorrhizal root per plant among the amendments. Increased P levels in the fertilizer- and sewage-amended subalpine spoil did not suppress VA mycorrhizal development. 43 refs., 6 tabs.

  2. Selenium transformation in coal mine spoils: Its environmental impact assessment. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Harness, J.; Atalay, A.; Koll, K.J.; Zhang, H.; Maggon, D.

    1991-12-31

    The objective of this program was to conduct an environmental impact assessment study for selenium from coal mine spoils. The use of in-situ lysimetry to predict selenium speciation, transformation, and mobility under natural conditions was evaluated. The scope of the study was to construct and test field-scale lysimeter and laboratory mini-column to assess mobility and speciation of selenium in coal mine overburden and soil systems; to conduct soil and groundwater sampling throughout the state of Oklahoma for an overall environmental impact assessment of selenium; and to conduct an in-depth literature review on the solubility, speciation, mobility, and toxicity of selenium from various sources. Groundwater and surface soil samples were also collected from each county in Oklahoma. Data collected from the lysimeter study indicated that selenium in the overburden of the abandoned mine site was mainly found in the selenite form. The amount of selenite found was too low and immobile to be of concern to the environment. The spoil had equilibrated long enough (over 50 years) that most of the soluble forms of selenium have already been lost. Examination of the overburden indicated the presence of pyrite crystals that precipitated over time. The laboratory mini-column study indicated that selenite is quite immobile and remained on the overburden material even after leaching with dilute acid. Data from groundwater samples indicated that based on the current permissible level for selenium in groundwater (0.01 mg Se/L), Oklahoma groundwater is widely contaminated with the element. However, according to the new regulation (0.05 mg Se/L), which is to be promulgated in 1992, only 9 of the 77 counties in the state exceed the limit.

  3. Assessment of the Influence of Dredge Spoil Dumping on the Seafloor Geological Integrity

    Directory of Open Access Journals (Sweden)

    Joonas J. Virtasalo

    2018-04-01

    Full Text Available The European Marine Strategy Framework Directive requires the development of suitable indicators for regular reporting on the environmental state and achievement of a good environmental status of EU's marine waters by 2020. The development of indicators for determining seafloor integrity and its possible disturbance by human activities have so far largely ignored the geological properties of seafloor. This paper presents a study of Vuosaari and Uusikaupunki-D offshore dumping sites in Finland, the northern Baltic Sea. Full coverage multibeam bathymetry and relative backscatter data, and a number of sediment cores were collected over the sites. The areas covered by dumped dredge spoil stand out in the multibeam images because of their irregular surface and elevated backscatter. The short gravity cores were studied for lithology, and in 1-cm slices for 137Cs activity, organic content, and grain size distribution. The dumped material is represented in the cores by the gravelly mud lithofacies with massive texture and angular coarse particles. The dumped material is coarser, less sorted and has higher kurtosis compared to natural sediment due to the admixing of blasted rock during the dredging activities, and limited sorting during fall through the water column upon dumping. Dispersed dredge spoil, which was suspended in the water column during the dumping activities or reworked from the dumped material mounds and redistributed along the seafloor soon thereafter, was deposited over a wide area as a thin layer that is not necessarily readily identifiable by visual inspection in the cores. Cesium activity helped distinguish the dumped material from the 137Cs-enriched natural sediments deposited after the 1986 Chernobyl disaster. Considering that the dumped material at many of the coring sites in the Vuosaari dumping area is covered by natural sediment, it probably is largely stable. In contrast, dumped material at the shallower Uusikaupunki-D site has

  4. Accumulation of some metals by legumes and their extractability from acid mine spoils

    International Nuclear Information System (INIS)

    Taylor, R.W.; Ibeabuchi, I.O.; Sistani, K.R.; Shuford, J.W.

    1992-01-01

    A greenhouse study was conducted to investigate the growth (dry matter yield) of selected legume cover crops; phytoaccumulation of metals such as Zn, Mn, Pb, Cu, Ni, and Al; the extractability of heavy metals from three different Alabama acid mine spoils. The spoils were amended based on soil test recommended levels of N, P, K, Ca and Mg prior to plant growth. Metals were extracted by three extractants (Mehlich 1, DTPA, and 0.1 M HCl) and values correlated with their accumulation by the selected legumes. Among the cover crops, kobe lespedeza Lespedeza striata (Thung.) Hook and Arn, sericea lespedeza Lespedeza cuneata (Dum.) G. Don, and red clover (Trifolium pratense L.) did not survive the stressful conditions of the spoils. However, cowpea (Vigna unguiculata L.) followed by 'Bragg' soybean Glycine max (L.) Merr. generally produced the highest dry matter yield while accumulating the largest quantity of metals, except Al, from spoils. The extractability of most metals from the spoils was generally in the order of: 0.1 MHCl > DTPA. Mehlich 1 did not extract Pb and 0.1 M HCl did not extract Ni, whereas DTPA extracted all the metals in a small amount relative to HCl and Mehlich 1. All the extractants were quite effective in removing plant-available Zn from the spoils. In general, the extractants' ability to predict plant-available metals depended on the crop species, spoil type, and extractant used. 28 refs., 4 tabs

  5. Nomograms to calculate stability in slate and granite spoil heaps; Abacos para el calculo de estabilidad en escombreras de pizarra y granito

    Energy Technology Data Exchange (ETDEWEB)

    Paz Freire, M.; Taboada Castro, J.; Rivas Brea, T.; Giraldez Perez, E.; Araujo Fernandez, M.

    2011-07-01

    One of the main problems involved in the mining of slate and ornamental granite is the unavoidable generation of waste rock, which must be stored in spoil heaps under suitably integrated, secure and stable conditions. Our work here focuses on this last point. To study the risk of instability within spoil heaps we have analysed the performance of a wide number of models with regard to circular slope failure, taking into account the different degrees of compactness of the material, the characteristics of the material itself, the effect of water pressure and the geometry of the heap. From this analysis we obtained more than 300 safety criteria, which were then used to draw up a series of nomograms to allow us to determine the risk of sliding in any granite or slate spoil heap. Thus, nomograms prove themselves to be suitable, quick, easy-to-use tools for preliminary studies of new structures, for periodic analyses of existing structures and to investigate structures that are due to be modified. (Author) 24 refs.

  6. Heavy metal concentration in forage grasses and extractability from some acid mine spoils

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, R.W.; Ibeabuchi, I.O.; Sistani, K.R.; Shuford, J.W. (Alabama A and M University, Normal (United States). Department of Plant and Soil Science)

    1993-06-01

    Laboratory and greenhouse studies were conducted on several forage grasses, bermudagrass ([ital Cynodon dactylon]), creeping red fescue ([ital Festuca rubra]), Kentucky 31-tall fescue ([ital Festuca arundinacea]), oat ([ital Avena sativa]), orchardgrass ([ital Dactylis glomerata]), perennial ryegrass ([ital Lolium perenne]), sorghum ([ital Sorghum bicolor]), triticale (X. [ital triticosecale Wittmack]), and winter wheat ([ital Triticum aestivum]) grown on three Alabama acid mine spoils to study heavy metal accumulation, dry matter yield and spoil metal extractability by three chemical extractants (Mehlich 1, DTPA, and 0.1 M HCl). Heavy metals removed by these extractants were correlated with their accumulation by several forage grasses. Among the forages tested, creeping red fescue did not survive the stressful conditions of any of the spoils, while orchard grass and Kentucky 31-tall fescue did not grow in Mulberry spoil. Sorghum followed by bermudagrass generally produced the highest dry matter yield. However, the high yielding bermudagrass was most effective in accumulating high tissue levels of Mn and Zn from all spoils (compared to the other grasses) but did not remove Ni. On the average, higher levels of metals were extracted from spoils in the order of 0.1 M HCl[gt] Mehlich 1[gt] DTPA. However, DTPA extracted all the metals from spoils while Mehlich 1 did not extract Pb and 0.1 M HCl did not extract detectable levels of Ni. All of the extractants were quite effective in determining plant available Zn from the spoils. For the other metals, the effective determination of plant availability depended on the crop, the extractant, and the metal in concert. 20 refs., 6 tabs.

  7. Identification of ecotype-specific marker genes for categorization of beer-spoiling Lactobacillus brevis.

    Science.gov (United States)

    Behr, Jürgen; Geissler, Andreas J; Preissler, Patrick; Ehrenreich, Armin; Angelov, Angel; Vogel, Rudi F

    2015-10-01

    The tolerance to hop compounds, which is mainly associated with inhibition of bacterial growth in beer, is a multi-factorial trait. Any approaches to predict the physiological differences between beer-spoiling and non-spoiling strains on the basis of a single marker gene are limited. We identified ecotype-specific genes related to the ability to grow in Pilsner beer via comparative genome sequencing. The genome sequences of four different strains of Lactobacillus brevis were compared, including newly established genomes of two highly hop tolerant beer isolates, one strain isolated from faeces and one published genome of a silage isolate. Gene fragments exclusively occurring in beer-spoiling strains as well as sequences only occurring in non-spoiling strains were identified. Comparative genomic arrays were established and hybridized with a set of L. brevis strains, which are characterized by their ability to spoil beer. As result, a set of 33 and 4 oligonucleotide probes could be established specifically detecting beer-spoilers and non-spoilers, respectively. The detection of more than one of these marker sequences according to a genetic barcode enables scoring of L. brevis for their beer-spoiling potential and can thus assist in risk evaluation in brewing industry. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Utilizing sediments from biological waste water treatment for spraying spoil banks

    Energy Technology Data Exchange (ETDEWEB)

    Bobrov, O G; Zaitsev, Yu S; Kessariiskii, Yu V

    1985-04-01

    Use of anaerobic sludge for prevention of spontaneous combustion of spoil banks consisting of coal and mine stones from underground coal mines and effects of sludge treatment on soil properties which influence spoil bank reclamation are discussed. Sludge from water treatment rich in organic matter (50 to 60%), nitrogen (2 to 5%), phosphorus anhydride (up to 2%), calcium oxide (up to 5%) and humus was used in the Donbass. A spoil bank consisted of sedimentary rocks (sandstones, limestones, shales, clays, mudstone) and coal (size 0 to 200 mm). Coal content ranged from 7-13%, sulfur content amounted to about 5%. Content of coal, sulfur and timber exceeded 20%. The spoil bank was treated with sludge suspension in water. Evaluations showed that the sludge treatment improved soil properties which influenced spoil bank reclamation. Humus content increased 7 to 16 times, content of nitrogen trioxide and phosphorus anhydride increased 10 to 50 times. Chemical activity of rocks forming the spoil bank declined 20 to 25%. Hazards of coal spontaneous combustion decreased. The results of investigations are shown in a table.

  9. Reforestation of bauxite mine spoils with Eucalyptus tereticornis Sm. seedlings inoculated with arbuscular mycorrhizal fungi

    Directory of Open Access Journals (Sweden)

    N. Krishnakumar

    2012-11-01

    Full Text Available Open cast mining for bauxite at Yercaud hills (India resulted indegradation of forest ecosystem and production of large quantities of waste rocks (called mine spoils. To ameliorate mine spoils, topsoil is used to spread over before the planting of tree species, conventional method as the topsoil has a good structure, water holding capacity and beneficial microbes like Arbuscular Mycorrhizal (AM fungi essential for plant growth.However, the use of top soil is expensive and in this study bauxite mine spoils were reforestated with AM fungi instead of it. The beneficial microbes AM fungi (Glomus aggregatum Schenck & Smith, G. fasciculatum(Thatcher Gerd. & Trappe emend. Walker & Koske, G. geosporum(Nicol. & Gerd. Walker were isolated, cultured and inoculated into the seedlings of Eucalyptus tereticornis Sm. and grown in bauxite mine spoils as potting medium under nursery conditions. Then, the biomass improved seedlings of E. tereticornis with inoculation of AM fungi were directly transplanted at bauxite mine spoils. After transplantation of the seedlings at bauxite mine spoils, the growth and survival rate were monitored for two years. The AM fungi inoculated seedlings of E. tereticornis showed 95% survival over the control seedlings and their growth was also significantlyhigher. Tissue nutrients (N, P, K were also found higher inAM fungi inoculated E. tereticornis than un inoculated control seedlings.

  10. Reforestation of Bauxite mine spoils with Eucalyptus tereticornis Sm. seedlings inoculated with Arbuscular mycorrhizal fungi

    Directory of Open Access Journals (Sweden)

    A. Karthikeyan

    2012-12-01

    Full Text Available Open cast mining for bauxite at Yercaud hills (India resulted in degradation of forest ecosystem and production of large quantities of waste rocks (called mine spoils. To ameliorate mine spoils, topsoil is used to spread over before the planting of tree species, conventional method as the topsoil has a good structure, water holding capacity and beneficial microbes like Arbuscular Mycorrhizal (AM fungi essential for plant growth. However, the use of top soil is expensive and in this study bauxite mine spoils were reforestated with AM fungi instead of it. The beneficial microbes AM fungi (Glomus aggregatum Schenck & Smith, G. fasciculatum (Thatcher Gerd. & Trappe emend. Walker & Koske, G. geosporum (Nicol. & Gerd. Walker were isolated, cultured and inoculated into the seedlings ofEucalyptus tereticornis Sm. and grown in bauxite mine spoils as potting medium under nursery conditions. Then, the biomass improved seedlings of E. tereticornis with inoculation of AM fungi were directly transplanted at bauxite mine spoils. After transplantation of the seedlings at bauxite mine spoils, the growth and survival rate were monitored for two years. The AM fungi inoculated seedlings ofE. tereticornis showed 95% survival over the control seedlings and their growth was also significantly higher. Tissue nutrients (N, P, K were also found higher in AM fungi inoculated E. tereticornis than un inoculated control seedlings. 

  11. Integration of thermal digital 3D model and a MASW (Multichannel Analysis of Surface Wave) as a means of improving monitoring of spoil tip stability

    Science.gov (United States)

    Lewińska, Paulina; Matuła, Rafał; Dyczko, Artur

    2018-01-01

    Spoil tips are anthropogenic terrain structures built of leftover (coal) mining materials. They consist mostly of slate and sandstone or mudstone but also include coal and highly explosive coal dust. Coal soil tip fires cause an irreversible degradation to the environment. Government organizations notice the potential problem of spoil tip hazard and are looking for ways of fast monitoring of their temperature and inside structure. In order to test new monitoring methods an experimental was performed in the area of spoil tip of Lubelski Węgiel "Bogdanka" S.A. A survey consisted of creating a 3D discreet thermal model. This was done in order to look for potential fire areas. MASW (Multichannel analysis of surface wave) was done in order to find potential voids within the body of a tip. Existing data was digitalized and a 3D model of object's outside and inside was produced. This article provides results of this survey and informs about advantages of such an approach.

  12. Integration of thermal digital 3D model and a MASW (Multichannel Analysis of Surface Wave as a means of improving monitoring of spoil tip stability

    Directory of Open Access Journals (Sweden)

    Lewińska Paulina

    2018-01-01

    Full Text Available Spoil tips are anthropogenic terrain structures built of leftover (coal mining materials. They consist mostly of slate and sandstone or mudstone but also include coal and highly explosive coal dust. Coal soil tip fires cause an irreversible degradation to the environment. Government organizations notice the potential problem of spoil tip hazard and are looking for ways of fast monitoring of their temperature and inside structure. In order to test new monitoring methods an experimental was performed in the area of spoil tip of Lubelski Węgiel „Bogdanka” S.A. A survey consisted of creating a 3D discreet thermal model. This was done in order to look for potential fire areas. MASW (Multichannel analysis of surface wave was done in order to find potential voids within the body of a tip. Existing data was digitalized and a 3D model of object’s outside and inside was produced. This article provides results of this survey and informs about advantages of such an approach.

  13. Response of alkali sacaton and fourwing saltbush to various amendments on coal mine spoils from northwestern New Mexico. II. Sodic spoil

    Energy Technology Data Exchange (ETDEWEB)

    Scholl, D G; Miyamoto, S

    1984-03-01

    Effects of chemical amendments on properties of two sodic mine spoils (sandstone and shale origins) and on growth of two range plants (alkali sacaton and fourwing saltbush) were studied in search of promising revegetation methods. The chemical amendments included applications of concentrated sulfuric acid, gypsum and phosphorus. On the shale spoil, these chemicals were applied in combination with physical amendments consisting of sand mulching, sand top-dressing, or sand incorporation. The sand used for the physical amendment was aeolian sand, which is locally available in the mine area. Laboratory water penetration tests and greenhouse plant growth tests were performed. Results indicate the following amendments to be promising: for sandstone-based spoils, sulfuric acid treatment, gypsum plus phosphorus application or phosphorus fertilization alone, depending on severity of sodium problems; for shale-based spoils, acid treatment can best be combined with either sand mulching, sand top-dressing, or sand incorporation. Gypsum plus phosphorus treatment in combination with sand top-dressing may provide an alternative treatment. 9 references.

  14. Occurrence of vesicular-arbuscular mycorrhizae in mixed overburden mine spoils of Texas

    Energy Technology Data Exchange (ETDEWEB)

    Mott, J.B.; Zuberer, D.A.

    1987-07-01

    Presently in east Texas, lignite surface mines are reclaimed and revegetated using mixed overburden materials which are equivalent to or better in physical-chemical properties than the poor topsoils removed during mining. Little information is available regarding the biological characteristics of levelled mixed overburden and the re-establishment of endomycorrhizal associations on revegetated mixed overburden sites. Therefore, the authors investigated the occurrence of infection of coastal bermudagrass (Cynodon dactylon), planted vegetatively on reclamation sites (1-10 years post-mining), with vesicular-arbuscular mycorrhizal (VAM) fungi. Numbers of spores were also monitored. For comparison, infection of coastal bermudagrass and spore numbers were determined for an unmined old field succession on soil typical of the region. VAM infection, measured as a percentage of root length infected or as a percentage of root segments exhibiting infection, returned to pre-mining levels by 3-7 years after disturbance. Intensity of infection was not altered by disturbance, age of reclaimed site, or season. Significantly greater numbers of spores (ca. 10-fold) were observed in the unmined soil and no differences were found between numbers of spores from variously aged mine spoil sites. 35 refs., 3 tabs.

  15. Inoculum density of Glomus mosseae and growth of onion plants in unsterilized bituminous coal spoil

    Energy Technology Data Exchange (ETDEWEB)

    Khan, A.G.

    1988-01-01

    The effect of inoculum, density (number of vesicular-arbuscular mycorrhizal (VAM) propagules g/sup -1/ of inoculum) on the growth of onions (Allium cepa L.) infected by Glomus mosseae (Nicol and Gerd). Gerdemann and Trappe, Comb nov in unsterilized coal spoil containing indigenous VAM fungi, including G. mosseae, was investigated. The amount of onion roots converted to mycorrhizas by inoculant fungus, estimated by a gridline intersect method, increased with inoculum density (..gamma..0.62, P0.05) until a plateau was reached. Onion growth responses also increased significantly (P<0.05) with the amount of VAM inoculum present in the coal spoil. The initial linear relationship between inoculum propagules (MPN estimates), percent colonization of onion roots and onion shoot dry weight became quadratic as the number of infection propagules increased. VAM infection had no significant effect on root:shoot ratios. Similarly there was no significant interaction (P>0.05) between the inoculum density, VAM-colonized root mass and the onion root:shoot fresh weight ratios. The amount of the windswept bituminous coal spoil bound to VAM (presumably because of VAM external hyphae) also increased as inoculum density increased (..gamma..0.63, P<0.05). There was a stronger correlation (ga0.85, P<0.05) between the amount of spoil adhered per plant and the root fresh wt plant/sup -1/ indicating that root effects were primarily responsible for increasing spoil adherence. There were negative correlations (P<0.05) between root fresh wt plant/sup -1/ (..gamma..-0.68), inoculum density (..gamma..-0.589), percent root elngth infected (..gamma..-0.73) and the amount of spoil adhered g/sup -1/ root fresh wt. The possible exploitation of VAM in revegetation of bituminous coal spoil is discussed. 25 refs., 2 tabs.

  16. Rehabilitation of semi-arid coal mine spoil bank soils with mine residues and farm organic by-products

    Energy Technology Data Exchange (ETDEWEB)

    Salazar, M.; Bosch-Serra, A.; Estudillos, G.; Poch, R.M. [University of Lleida, Lleida (Spain). Dept. of Environmental & Soil Science

    2009-07-01

    A method of rehabilitating coal mine soils was studied under the conditions of a semi-arid climate, lack of topsoil but availability of farm by-products in NE Spain. The objectives of the research were to assess a new method in order to achieve a suitable substrate for the establishment of native vegetation, to evaluate environmental impacts associated with the reclamation process, and to determine the time necessary to integrate the treated area into the surrounding environment. Eight plots (10 x 35 m{sup 2}) were established in September 1997. Substrate combinations of two types of mine spoil (coal dust and coarse-sized material), two levels of pig slurry (39 and 94 Mg ha{sup -1}dry-wt), and cereal straw (0 and 15 Mg ha{sup -1}) were applied. Monitoring of select physical and chemical soil properties and vegetation characteristics was performed from 1997 until 2005. The bulk density and the saturated hydraulic conductivity measured did not limit plant development and water availability. Initial substrate salinity (1.37 S m{sup -1}) decreased with time and in the long term did not limit plant colonization to salinity-adapted species. Initial nitrate concentration was 298 mg kg{sup -1}, but was reduced significantly to acceptable values in 3 years (55 mg kg{sup -1}) and the measured pH (7.6) was maintained at the level of initial spoil values. Vegetation cover reached up to 90%. In the treated area, spontaneous vegetation cover (15 to 70%) colonized the nonsown areas widely. In the medium term, vegetation cover tended to be higher in plots with a thicker layer of coal dust material and the higher slurry rate. Soil rehabilitation and environmental reintegration, taking into account soil and vegetation indicators, was possible in the studied area with low cost inputs using residual materials from mining activities and animal husbandry by-products.

  17. Establishment of native species on amended and unamended coal mine spoil in central Queensland

    International Nuclear Information System (INIS)

    Bell, L.C.; Mulligan, D.R.; Orr, M.S.; Johnstone, P.

    1994-01-01

    At the Curragh open-cut coal mine in central Queensland, tree and shrub growth on amended and unamended spoil was assessed over a 5-year period. The most successful media in terms of seedling densities were bare spoil and spoil covered by a thin layer of coarse coal reject. Where soil was replaced, very few native species established due to the intense competition from exotic grasses. Given this poor establishment on soil, the question of how well an ecosystem would develop on non-soil media was addressed by assessing the ability of each of the media to support sustainable communities in the longer term. Early results from direct-seeding tree and shrub species onto non-soil media have been quite encouraging, but analysis of the surface horizons has shown that after several years, there are still some characteristics which could either limit the re-establishment, and/or prevent the sustainability, of new communities. Due primarily to the high sulfate levels originally in the coal reject, the surface salinity in these treatments was much higher than in the uncapped spoil. Substrate analyses have shown also that there was a much lower concentration of mineralizable N in the spoil and coal reject than in the soil, revealing that the potential of these non-soil substrates to continue supplying nitrogen to the system is greatly reduced. Furthermore, the concentration of microbial biomass carbon was significantly lower in these media, and the percentage ground cover after 5 years was generally <10%

  18. Traditional method of fish treatment, microbial count and palatability studies on spoiled fish

    Directory of Open Access Journals (Sweden)

    Abd Aziz, N. A.

    2013-01-01

    Full Text Available Aims: To evaluate the microbial count and palatability acceptance of spoiled fish after treatment with traditionally used naturalsolution.Methodology and results: To compare microbial count of spoiled fish before and after treatment with natural solution practicedby local people in Malaysia, 10 g of spoiled fish was respectively rinsed with 100 mL of 0.1% of natural solution such as Averrhoabilimbi extract, rice rinsed water, rice vinegar, Citrus aurantifolia extract, salt, flour, and Tamarindus indica extract. Flesh of fishrinsed with rice vinegar was found to be able to reduce microbial count (CFU/mL = 0.37 X 107 more than 4.5 times whencompared to spoiled fish (CFU/mL=1.67x 107. Spoiled fish that was treated with rice vinegar was prepared into a cutlet and fried.The cutlet was subjected to palatability acceptance study by a group of residents in Palm Court Condominium, Brickfields, KualaLumpur. The palatability study from the Cronbach alpha shown that the taste have the reliability of 0.802, the aroma has thereliability of 0.888, colour with the reliability of 0.772, texture or mouth feel have reliability of 0.840 and physical structure of thecutlet is 0.829.Conclusion, significance and impact of study: Treatment of spoiled fish using rice vinegar as practice by local peopletraditionally shown a significant reduction in microbial count and the vinegar-treated fish could be developed into a product that issafe and acceptable by the consumer.

  19. Remediation of an acidic mine spoil: Miscanthus biochar and lime amendment affects metal availability, plant growth and soil enzymatic activity

    Science.gov (United States)

    Biochar is proposed as an amendment for mine spoil remediation; however, its effectiveness at achieving this goal remains unclear. Miscanthus (Miscanthus giganteus) biochar was tested for potentially improving acidic mine spoil (pH < 3; Formosa mine near Riddle, Oregon) health conditions by sequeste...

  20. Growth strategy of heterotrophic bacterial population along successional sequence on spoil of brown coal colliery substrate

    Czech Academy of Sciences Publication Activity Database

    Krištůfek, Václav; Elhottová, Dana; Chroňáková, Alica; Dostálková, I.; Picek, T.; Kalčík, Jiří

    2005-01-01

    Roč. 50, č. 5 (2005), s. 427-435 ISSN 0015-5632 R&D Projects: GA ČR(CZ) GA526/03/1259 Institutional research plan: CEZ:AV0Z60660521 Keywords : growth strategy * heterotrophic bacterial population * brown coal colliery spoil Subject RIV: EH - Ecology, Behaviour Impact factor: 0.918, year: 2005

  1. Heavy metals in soil on spoil heap of an abandoned lead ore ...

    African Journals Online (AJOL)

    EJIRO

    (Ti, Fe and Al) of a soil profile on spoil heap were examined. 54 soil samples were .... move gravel and rocks, put in plastic bags then sent to the Service. Central du ..... micro- organisms and microbial processes in agricultural soils. A review.

  2. Forest-biological erosion control on coal-mine spoil banks in Bulgaria

    International Nuclear Information System (INIS)

    Haigh, M.J.; Gentcheva-Kostadinova, S.; Zheleva, E.

    1995-01-01

    The forest fallowing of coal-mine spoils helps re-establish the processes of natural, self-sustaining, soil formation. Environmental monitoring in Bulgaria demonstrates that forestation can moderate soil pH (from ph> 3.0 to pH 1.3 g/cm 3 in the 0-5 cm layer) in the case of coal briquette spoils at Pernik, near Sofia. Ground losses from forested, 16-17 degree slope, coal briquette-spoils at Pernik are a quarter of those from an entirely unvegetated section of the same embankment (48.5 vs 12. 1 mm in the period 1988-1994) despite the absence of ground cover beneath the trees. On lignite spoil banks, at Maritsa-Iztok, central Bulgaria, forestation increases the organic content of the soil to greater depths than revegetation with grass, and to a greater degree than conventional agricultural cultivation. On Pinus nigra forested crest sites at Pernik, and in Robinia pseudacacia forested groves on the lignite minespoil banks at Maritsa-Iztok, slopes showed ground advance rather than ground retreat. Slopes protected by mechanical means alone did not allow soil growth and, where the structure broke down, they suffered as much erosion as untreated sites. In sum, the forest fallowing of surface coal-mine disturbed land accelerates organic matter accumulation in the soil, helps improve soil structure, reduces erosion, and may transform soil loss into soil gain, even on steeply sloping sites. 17 refs., 3 figs., 1 tab

  3. 30 CFR 817.72 - Disposal of excess spoil: Valley fill/head-of-hollow fills.

    Science.gov (United States)

    2010-07-01

    ... STANDARDS-UNDERGROUND MINING ACTIVITIES § 817.72 Disposal of excess spoil: Valley fill/head-of-hollow fills.... Uncontrolled surface drainage may not be directed over the outslope of the fill. (2) Runoff from areas above the fill and runoff from the surface of the fill shall be diverted into stabilized diversion channels...

  4. In vivo quantitative NMR imaging of fruit tissues during growth using Spoiled Gradient Echo sequence

    DEFF Research Database (Denmark)

    Kenouche, S.; Perrier, M.; Bertin, N.

    2014-01-01

    of this study was to design a robust and accurate quantitative measurement method based on NMR imaging combined with contrast agent (CA) for mapping and quantifying water transport in growing cherry tomato fruits. A multiple flip-angle Spoiled Gradient Echo (SGE) imaging sequence was used to evaluate...

  5. Earthworm succession in afforested colliery spoil heaps in the Sokolov region, Czech Republic

    Czech Academy of Sciences Publication Activity Database

    Pižl, Václav

    2001-01-01

    Roč. 9, č. 4 (2001), s. 359-364 ISSN 1061-2971 Institutional research plan: CEZ:AV0Z6066911 Keywords : earthworms * colliery spoil heaps * succession Subject RIV: EH - Ecology, Behaviour Impact factor: 1.011, year: 2001

  6. Colonization of spoil benches of an opencast lignite mine in northwest Spain by amphibians and reptiles

    Energy Technology Data Exchange (ETDEWEB)

    Galan, P. [University of Santiago de Compostela, Santiago de Compostela (Spain). Faculty of Biology

    1997-02-01

    This paper discusses the colonization by reptiles and amphibians of the spoil benches of the Meirama opencast lignite mine in northwest Spain over 10 years, following the start of the revegetation process. At Meirama, spoil benches are initially fertilized and hydroseeded with a pasture mix, but are subject to little subsequent management and are gradually colonized by scrub vegetation characteristic of the region. Herpetofauna censuses were carried out yearly on a single 2 ha plot over 6 years following hydroseeding, and in a single year on ten 2 ha plots which had been hydroseeded between 0 and 10 years previously. In addition, censuses were carried out on three undisturbed `control` plots close to the mine. Fifteen species (nine amphibians and six reptiles) were detected in one or more of the spoil-bench plots. Recolonization was particularly rapid after the first 2-3 years post-hydroseeding, and was closely related to habitat development due to revegetation and natural succession. Species composition was most similar to that in control plots in the oldest (ten-year-old) spoil plots.

  7. Survival and growth of wildlife shrubs and trees on acid mine spoil

    Energy Technology Data Exchange (ETDEWEB)

    Fowler, D.K.; Adkisson, L.F.

    1980-01-01

    The purpose of this study was to assess the survival and growth of selected wildlife plants over a wide range of acid mine spoil conditions and to identify species suitable for surface mine reclamation. A major criterion in selection of study sites was inclusion of a wide range of spoil acidity conditions. The Ollis Creek (Study Area A) and Farrell (Study Area B) coal surface mines located in Campbell and Scott Counties, Tennessee, were selected for study. Seven plant species, all of which had been used in past reclamation demonstrations, were introduced on the 22 plots during March 1972. Autumn olive (Elaeagnus umbellata) was included as a control plant. Ten additional plant species were introduced during March 1973. With the exception of highbush blueberry (Vaccinium corymbosum var.). European filbert (Corylus avellana), and red maple (Acer rubrum), these species had not been used in TVA reclamation demonstrations. To assess the effects of spoil pH on the plants, the plots were grouped into seven pH categories, and mean percent survival and growth for each species were calculated. Results indicate that autumn olive, elaeagnus cherry, arnot locust, sawtooth oak, red maple, and Toringo crabapple are suitable for quick improvement of surface mine habitat over a wide range of spoil acidity in the Appalachian coalfield. Bessey cherry and European filbert need further study before a decision can be made regarding their reclamation utility. Species that are not recommended for quick habitat improvement over a wide range of surface mine spoil pH conditions include bush honeysuckle, barberry, Siberian crabapple, Manchu cherry, American beautyberry, bear oak, blueberry, rem-red honeysuckle, and redcedar.

  8. Dry flue gas desulfurization byproducts as amendments for reclamation of acid mine spoil

    International Nuclear Information System (INIS)

    Dick, W.A.; Stehouwer, R.C.; Beeghly, J.H.; Bigham, J.M.; Lal, R.

    1994-01-01

    Development of beneficial reuses of highly alkaline, dry flue gas desulfurization (FGD) byproducts can impact the economics of adopting these FGD technologies for retrofit on existing powerplants. Greenhouse studies were conducted to evaluate the use of two dry FGD byproducts for reclamation of acid mine spoil (pH, 3.1 to 5.8). Treatment rates of FGD ranges from 0% to 32% by dry weight and most treatments also included 6% by dry weight of sewage sludge. Fescue (Festuca arundinacea Schreb.) was harvested monthly for a total of six harvests. Plant tissue composition and root growth were determined after the sixth harvest. Leachate analyses and pH determination of mixes were done at the beginning and end of the experiments. Both FGD byproducts were effective in raising the spoil pH and in improving fescue growth. At the highest FGD application rate, fescue growth decreased from the optimum due to high pH and reduced rooting volume caused by cementation reactions between the FGD and spoil. Trace elements, with the exception of B, were decreased in the fescue tissue when FGD was applied. Leachate pH, electrical conductivity, dissolved organic carbon, Ca, Mg, and S tended to increase with increased FGD application rate; Al, Fe, Mn, and Zn decreased. pH was the most important variable controlling the concentrations of these elements in the leachate. Concentrations of elements of environmental concern were near or below drinking water standard levels. These results indicate that FGD applied at rates equivalent to spoil neutralization needs can aid in the revegetation of acid spoil revegetation with little potential for introduction of toxic elements into the leachate water or into the food chain

  9. Remedial investigation report on Bear Creek Valley Operable Unit 2 (rust spoil area, spoil area 1, and SY-200 yard) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. Volume 2. Appendixes

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-01

    This document contains the appendices to the Remedial Investigation Report on Bear Creek Valley Operable Unit 2 (Rust Spoil Area, Spoil Area 1, and SY-200 Yard) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. The appendices include Current and historical soil boring and groundwater monitoring well information, well construction logs, and field change orders; Analytical data; Human health risk assessment data; and Data quality.

  10. Remedial investigation report on Bear Creek Valley Operable Unit 2 (rust spoil area, spoil area 1, and SY-200 yard) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. Volume 2. Appendixes

    International Nuclear Information System (INIS)

    1994-08-01

    This document contains the appendices to the Remedial Investigation Report on Bear Creek Valley Operable Unit 2 (Rust Spoil Area, Spoil Area 1, and SY-200 Yard) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. The appendices include Current and historical soil boring and groundwater monitoring well information, well construction logs, and field change orders; Analytical data; Human health risk assessment data; and Data quality

  11. Weathering processes under various moisture conditions in a lignite mine spoil from As Pontes (N.W. Spain)

    International Nuclear Information System (INIS)

    Seoane, S.; Leiros, M.C.

    1997-01-01

    Processes contributing to acid release/consumption during weathering of a lignite mine spoil (2.3% w/w S as sulfides) from As Pontes (N.W. Spain) were studied under three moisture conditions (at field capacity or under alternate wetting-drying or forced percolation), which were simulated in laboratory experiments. Oxidation of sulfides to sulfates was favoured under all three moisture conditions, releasing most acid in spoil kept at field capacity. Hydroxysulfates formed in spoil kept at field capacity or under alternate wetting-drying conditions, thereby contributing to acid release. Acid consumption by dissolution of clay minerals, especially micas, was favoured under all three moisture conditions, but was particularly intense in spoil at field capacity. Dissolution of aluminium oxides was also favoured under all the moisture conditions studied. 27 refs., 8 figs., 6 tabs

  12. The copper spoil heap Knappenberg, Austria, as a model for metal habitats – Vegetation, substrate and contamination

    Energy Technology Data Exchange (ETDEWEB)

    Adlassnig, Wolfram; Weiss, Yasmin S. [University of Vienna, Core Facility Cell Imaging and Ultrastructure Research, Althanstraße 14, A-1090 Vienna (Austria); Sassmann, Stefan [University of Vienna, Core Facility Cell Imaging and Ultrastructure Research, Althanstraße 14, A-1090 Vienna (Austria); University of Exeter, College of Life and Environmental Sciences, Biosciences, Stocker Road, Exeter EX4 4QD (United Kingdom); Steinhauser, Georg [Leibniz University Hannover, Institute of Radioecology and Radiation Protection, Herrenhäuser Straße 2, D30419 Hannover (Germany); Hofhansl, Florian [University of Vienna, Department of Microbiology and Ecosystem Science, Althanstraße 14, A-1090 Vienna (Austria); Instituto Nacional de Pesquisas da Amazônia, Coordenação de Dinâmica Ambiental, Manaus (Brazil); Baumann, Nils [Helmholtz-Zentrum Dresden-Rossendorf, Division of Biogeochemistry, Bautzner Landstraße 400, D-01328 Dresden (Germany); Lichtscheidl, Irene K. [University of Vienna, Core Facility Cell Imaging and Ultrastructure Research, Althanstraße 14, A-1090 Vienna (Austria); Lang, Ingeborg, E-mail: ingeborg.lang@univie.ac.at [University of Vienna, Core Facility Cell Imaging and Ultrastructure Research, Althanstraße 14, A-1090 Vienna (Austria)

    2016-09-01

    Historic mining in the Eastern Alps has left us with a legacy of numerous spoil heaps hosting specific, metal tolerant vegetation. Such habitats are characterized by elevated concentrations of toxic elements but also by high irradiation, a poorly developed substrate or extreme pH of the soil. This study investigates the distribution of vascular plants, mosses and lichens on a copper spoil heap on the ore bearing Knappenberg formed by Prebichl Layers and Werfener Schist in Lower Austria. It serves as a model for discriminating between various ecological traits and their effects on vegetation. Five distinct clusters were distinguished: (1) The bare, metal rich Central Spoil Heap was only colonised by highly resistant specialists. (2) The Northern and (3) Southern Peripheries contained less copper; the contrasting vegetation was best explained by the different microclimate. (4) A forest over acidic bedrock hosted a vegetation overlapping with the periphery of the spoil heap. (5) A forest over calcareous bedrock was similar to the spoil heap with regard to pH and humus content but hosted a vegetation differing strongly to all other habitats. Among the multiple toxic elements at the spoil heap, only Cu seems to exert a crucial influence on the vegetation pattern. Besides metal concentrations, irradiation, humidity, humus, pH and grain size distribution are important for the establishment of a metal tolerant vegetation. The difference between the species poor Northern and the diverse Southern Periphery can be explained by the microclimate rather than by the substrate. All plant species penetrating from the forest into the periphery of the spoil heap originate from the acidic but not from the calcareous bedrock. - Highlights: • Strong impact on plant diversity by isolation and extreme abiotic conditions • Both, microclimate and substrate explain species distribution. • Increased cellular metal tolerance of plants from the Central Spoil Heap • Among toxic elements

  13. Measurements of line overlap for resonant spoiling of x-ray lasing transitions

    International Nuclear Information System (INIS)

    Beiersdorfer, P.; Elliott, S.R.; MacGowan, B.J.; Nilsen, J.

    1994-06-01

    High-precision measurements are presented of candidate line pairs for resonant spoiling of x-ray lasing transitions in the nickel-like W 46+ , the neon-like Fe 16+ , and the neon-like La 47+ x-ray lasers. Our measurements were carried out with high-resolution crystal spectrometers, and a typical precision of 20--50 ppM was achieved. While most resonances appear insufficient for effective photo-spoiling, two resonance pairs are identified that provide a good overlap. These are the 4p 1/2 → 3d 3/2 transition in nickel-like W 46+ with the 2p 3/2 → 1s 1/2 transition in hydrogenic Al 12+ , and the 3s 1/2 → 2p 3/2 transition in neon-like La 47+ with the 1 1 S 0 -2 1 P 1 line in heliumlike Ti 20+

  14. The development of arbuscular mycorrhiza in two simulated stages of spoil-bank succession

    Czech Academy of Sciences Publication Activity Database

    Püschel, David; Rydlová, Jana; Vosátka, Miroslav

    2007-01-01

    Roč. 35, č. 2 (2007), s. 363-369 ISSN 0929-1393 R&D Projects: GA ČR GA526/04/0996; GA ČR(CZ) GD206/03/H137 Institutional research plan: CEZ:AV0Z60050516 Keywords : mycorrhiza * plant succession * spoil bank s Subject RIV: EF - Botanics Impact factor: 1.810, year: 2007

  15. Stillbirth and stigma: the spoiling and repair of multiple social identities

    OpenAIRE

    Brierley-Jones, L.; Crawley, R.; Lomax, S.; Ayers, S.

    2014-01-01

    This study investigated mothers' experiences surrounding stillbirth in the United Kingdom, their memory making and sharing opportunities, and the effect these opportunities had on them. Qualitative data were generated from free text responses to open-ended questions. Thematic content analysis revealed that "stigma" was experienced by most women and Goffman's (1963) work on stigma was subsequently used as an analytical framework. Results suggest that stillbirth can spoil the identities of "pat...

  16. Usefulness of enhanced breathhold 3D spoiled gradient-echo MRA for intrathoracic mass

    International Nuclear Information System (INIS)

    Kobayashi, Takeshi; Kadoya, Masumi; Kamimura, Ryoichi; Takashima, Tsutomu

    1999-01-01

    Enhanced Breathhold 3D Spoiled Gradient-echo MRA was very attractive method for not only evaluating relationship between intrathoracic mass and intrathoracic vessels, but also visualizing small pulmonary vessels that could not be detected conventional MRA methods. Moreover, this methods could be applied for evaluating vascularity of the lesions. This method will be accepted as routine pulse sequence for evaluating intrathoracic mass especially malignant tumors. (author)

  17. Cover layers to the growth of trees and shrobs over a sulfide spoil from gold mining

    Directory of Open Access Journals (Sweden)

    Igor Rodrigues de Assis

    2011-08-01

    Full Text Available This work was done at a gold mine company in Paracatu, MG, Brazil, and was conducted from March 2000 to November 2005. The substrate (spoil studied was a phillite rock which contains sulfides such as pyrite and arsenopyrite. This study aimed to evaluate the survival and growth of plant species on different combinations of substrate layers over the spoil. These layers were a cover layer and a sealing layer, both deposited over the spoil. The treatment 1 had saprolite (B1 in the sealing layer (SL and B1 with liming (B1L in the cover layer (CL. The treatment 2 had B1 in SL and B1L + soil with liming (SoL in the CL. The treatment 3 had B1 + SoL in the SL and B1L in the CL. The treatment 4 had B1 + SoL in the SL and B1L + SoL in the CL. The plant species used were Acacia farnesiana, A. holosericea, A. polyphylla, Albizia lebbeck, Clitoria fairchildiana, Flemingia sp., Mimosa artemisiana, M. bimucronata e Enterolobium contortisiliquum. Forty and 57 months after planting, collardiameter, height, and living plants were evaluated. The greatest survival rate was oobservedintreatmentwith B horizon of an Oxisoil in both layers, with 80 %. In general, M. bimucronata and A. farnesiana species showed the highest survival rate. The arsenic-content by Mehlich 3 in the cover layer ranged from 0.00 to 14.69 mg dm- 3 among treatments. The experimental results suggest that layers combinations above the sulfide substrate allow the rapid revegetation of the spoil.

  18. Sensitivity of spoiling and pathogen food-related bacteria to Origanum vulgare L. (Lamiaceae) essential oil

    OpenAIRE

    Souza,Evandro Leite de; Stamford,Tânia Lúcia Montenegro; Lima,Edeltrudes de Oliveira

    2006-01-01

    Origanum vulgare L. (oregano), Lamiaceae, has been known as plant specie with prominent biological properties for a long time. This study aimed to evaluate the antibacterial activity of Origanum vulgare essential oil on various Gram-positive and Gram-negative spoiling and/or pathogen food-related bacteria, as well as to observe its antimicrobial effectiveness in a food conservation micromodel. The results showed a strong antibacterial activity of the assayed essential oil noted by large growt...

  19. Remediation of Acid Generating Colliery Spoil Using Steel Slag – Case Studies

    Directory of Open Access Journals (Sweden)

    Ghataora Gurmel S.

    2015-06-01

    Full Text Available One of the legacies of the coal mining industry is the existence of numerous colliery spoil mounds. Run-off waters from some of these mounds result in oxidation of sulphur compounds causing pH to drop to perhaps as low as 2.5. At this pH, mobility for metals increases and it results in destruction of both flora and fauna. In order to reduce acidity, a number of solutions have been investigated with varying degree of success. A recent study to reduce acidity in spoil run-off water included the use of Basic Oxygen Steel slag. Its slow release of lime resulted in longer term remediation compared with other techniques. In addition to this, steel slag contains elements which are essential for plant growth and can be regarded as a weak fertiliser. This was substantiated in two field trials, which had the aim of not only remediating acidity from two different types of colliery spoils, but also to develop a composition that supports grass growth. The objectives were achieved at both sites and some of the results of over 5000 chemical tests conducted during these studies are reported in this paper.

  20. Reclamation of acidic colliery spoil. III. Problems associated with the use of high rates of limestone

    Energy Technology Data Exchange (ETDEWEB)

    Costigan, P A [Univ. of Liverpool, England; Bradshaw, A D; Gemmell, R P

    1982-04-01

    Growth of Trifolium repens in acidic colliery spoil was suppressed by more than 90% when agricultural ground calcitic limestone was applied at above 5 t ha/sup -1/ whereas Lolium perenne was unaffected at rates up to 100 t ha/sup -1/. The inhibitory effect of ground limestone on T. repens was reduced by high phosphorus fertilization and disappeared within 34 weeks of treatment.There was some evidence that high liming caused an imbalance of the Ca/Mg ratio in freshly limed spoil, contribution to growth inhibition. Growth of L. perene was improved and the inhibitory effect on T. repens was alleviated by substituting magnesian limestone (dolomite) for calcitic limestone. Phosphate adsorption of spoil was similar after low and very high limestone applications but increased by 100% after liming at 25 t ha/sup -1/ to pH 5.1.It is suggested that phosphate adsorption at pH 5.1 is caused by freshly precipitated amorphous aluminium hydroxide. The practical implications of the results are discussed.

  1. Effects of coal spoil amendment on heavy metal accumulation and physiological aspects of ryegrass (Lolium perenne L.) growing in copper mine tailings.

    Science.gov (United States)

    Chu, Zhaoxia; Wang, Xingming; Wang, Yunmin; Liu, Guijian; Dong, Zhongbing; Lu, Xianwen; Chen, Guangzhou; Zha, Fugeng

    2017-12-21

    Copper mine tailings pose many threats to the surrounding environment and human health, and thus, their remediation is fundamental. Coal spoil is the waste by-product of coal mining and characterized by low levels of metals, high content of organic matter, and many essential microelements. This study was designed to evaluate the role of coal spoil on heavy uptake and physiological responses of Lolium perenne L. grown in copper mine tailings amended with coal spoil at rates of 0, 0.5, 1, 5, 10, and 20%. The results showed that applying coal spoil to copper mine tailings decreased the diethylenetriaminepentaacetic acid (DTPA)-extractable Cd, Cu, Pb, and Zn contents in tailings and reduced those metal contents in both roots and shoots of the plant. However, application of coal spoil increased the DTPA-extractable Cr concentration in tailings and also increased Cr uptake and accumulation by Lolium perenne L. The statistical analysis of physiological parameters indicated that chlorophyll and carotenoid increased at the lower amendments of coal spoil followed by a decrease compared to their respective controls. Protein content was enhanced at all the coal spoil amendments. When treated with coal spoil, the activities of superoxide dismutases (SOD), peroxidase (POD), and catalase (CAT) responded differently. CAT activity was inhibited, but POD activity was increased with increasing amendment ratio of coal spoil. SOD activity increased up to 1% coal spoil followed by a decrease. Overall, the addition of coal spoil decreased the oxidative stress in Lolium perenne L., reflected by the reduction in malondialdehyde (MDA) contents in the plant. It is concluded that coal spoil has the potential to stabilize most metals studied in copper mine tailings and ameliorate the harmful effects in Lolium perenne L. through changing the physiological attributes of the plant grown in copper mine tailings.

  2. Infilling Littleton Street Mine, Wallsall, with colliery spoil rock paste

    Energy Technology Data Exchange (ETDEWEB)

    Jarvis, S.T.; Braithwaite, P.A. [Ove Arup and Partners, Birmingham (United Kingdom)

    1993-12-31

    Describes the filling of an abandoned underground mine with low strength (12-20 kPa) paste made of coal mining waste. With a volume of 550,000 m{sup 3}, it was the largest mine to be filled with rock paste to date. The abandoned mine, flooded with underground water, consists of room and pillar workings at shallow depth of 35 to 60 m. Height of the underground mine cavity varies between 4 and 8 m. The process of infilling and tests and systems for monitoring infilling completeness and strength are described. Benefits of rock paste over other forms of infilling are discussed. Land reclamation work at the source sites is also described. Mineral waste source sites and specifications of the materials are given. After work completion, about 18 ha of derelict urban land were released for redevelopment. 6 refs.

  3. Selecting colliery spoil from Puentes mine for the purpose of tip restoration. Influencia de la seleccion de los esteriles de la Mina Puentes en la restauracion de la escombrera

    Energy Technology Data Exchange (ETDEWEB)

    Gil Bueno, A; Macias Vazquez, F; Monterroso Martinez, C; Val Caballero, C

    1990-12-01

    Presents the results of a study conducted into the physical and chemical properties of material from coal faces at Puentes Mine in the La Coruna region of Spain. The main objective was to study waste material with a view to selecting the type most suitable to act as the covering layer for colliery spoil tips. The selection method employed has created tips with a top layer suitable for planting. The article also describes the methods used in the restoration work. 6 refs., 3 tabs., 4 figs.

  4. Enzyme activities in reclaimed coal mine spoils and soils

    Energy Technology Data Exchange (ETDEWEB)

    Fresquez, P R; Aldon, E F; Lindemann, W C

    1987-11-01

    The segregation and stockpiling of topsoil material may reduce enzymatic activities that may hinder normal nutrient cycling processes in reclaimed minelands. The effects of topsoiling and reclamation age on dehydrogenase, nitrogenase, phosphatase, arylsulphatase, amylase, cellulase, invertase and urease activities were evaluated on three reclaimed non-top-soiled and five reclaimed topsoiled areas and compared with an indisturbed reference soil. Three months after topsoiling and revegetation, activities of the enzymes in the reclaimed areas, with the exception of dehydrogenase, were statistically equal to activities of the undisturbed soil. Most enzymes, including dehydrogenase, peaked in the next 1 or 2 years after reclamation with topsoiling and declined thereafter. A 4-year-old topsoiled site (revegetated in 1978) was statistically similar to the undisturbed soil. Amylase activity, however, was significantly lower after the fourth year compared to the undisturbed soil. The non-topsoiled areas, even after 6, 7 and 8 years, appeared to have lower enzyme activities than the younger topsoiled areas or the undisturbed soil. This trend was supported by the finding that the 4-year-old topsoiled site was more enzymatically similar to the undisturbed soil than was the 8-year-old non-topsoiled site (revegetated in 1974). The low enzyme acitivities found in the non-topsoiled areas may be a result of their adverse chemical and physical properties, as well as the low diversity of microorganisms. These studies demonstrate the value of topsoil use for early establishment of soil processes in reclaimed areas. 3 figs., 19 refs., 8 tabs.

  5. Spatial variation in spoil and vegetative characteristics of pastures on reclaimed surface mined land

    International Nuclear Information System (INIS)

    Teutsch, C.D.; Collins, M.; Ditsch, D.C.

    1999-01-01

    Kentucky has large areas of reclaimed surface mined land that could provide grazing for livestock. Research is needed to determine optimal stocking densities and to evaluate the sustainability of such grazing systems for this region. A long-term grazing study was initiated in 1997 on 151 ha of reclaimed land near Chavies, KY to determine spatial and temporal variation with stocking densities of 0, 0.28, 0.42, or 0.83 beef cow-calf units/ha. Global Positioning System and GIS technologies were used to establish pasture boundaries, locate permanent sampling markers at a density of 1 per 0.4 ha, and interpolate maps of physical, spoil, and vegetable pasture characteristics. Herbage and spoil samples were collected around the permanent markers in May of 1997. Stepwise regression was used to determine factors affecting the vegetative characteristics of the sites. Biomass density ranged from 0 to 2500 kg/ha with a mean of 570 kg/ha. Factors affecting biomass included legume and weed proportions in the sward, grazing activity, soil potassium, elevation, and potential acidity, cumulatively accounting for 32% of the variation. Ground cover ranged from 10 to 100% with an average of 74%. Soil pH, potassium, and grass in the sward accounted for 14% of the variation in ground cover. Legumes made up 0 to 61% of the sward with a mean of 13% over the pasture area. Variables affecting the amount of legume in the sward included biomass density, slope, elevation, pH, and stocking density, together accounting for 21% of the variation. Spatial variation in the physical, spoil, and vegetative characteristics of the pastures was large. Overall, regression accounted for a limited amount of the variation in the vegetative characteristics of the site indicating that other important variables exist

  6. An assessment of processes for the manufacture of synthetic aggregates from colliery spoil

    Energy Technology Data Exchange (ETDEWEB)

    Nixon, P J; Gartner, E M

    1980-09-01

    Following the laboratory development of a process for the manufacture of synthetic aggregates from colliery spoil for use in structural concrete, a technical and economic assessment of possible processing routes is reported. Rotary kilns, multi-hearth furnaces, sinter-strands, shaft kilns and fluidised bed furnaces are considered and capital and running costs for the various processes are estimated. It is concluded that the initial capital costs of plant are the main barrier to successful exploitation. The cost of fuel for sintering is over-shadowed by the costs of capital investment and electric power, so efforts to reduce fuel consumption are unlikely to make a process economic in themselves.

  7. Anthropogenic soils on spoil rock banks in North Bohemian Coal Basin, Czech Republic

    International Nuclear Information System (INIS)

    Raclavska, H.; Raclavsky, K.; Matysek, D.; Stalmachova, B.

    1997-01-01

    The area of the North Bohemian Coal Basin is devastated by the extensive exploitation of brown coal by open pit mining. Knowledge of newly formed soils, their properties, development and contamination is important from the point of view of biological regeneration of the landscape. The mineralogy of anthropogenic soils from the mining area is presented together with the geochemistry of nutrients and trace elements. Attention is paid to the soil-forming processes in the non-reclaimed spoil rock banks with the development of spontaneous vegetation. 3 refs., 1 fig., 4 tabs

  8. Mine spoil prairies expand critical habitat for endangered and threatened amphibian and reptile species

    Science.gov (United States)

    Lannoo, Michael J.; Kinney, Vanessa C.; Heemeyer, Jennifer L.; Engbrecht, Nathan J.; Gallant, Alisa L.; Klaver, Robert W.

    2009-01-01

    Coal extraction has been occurring in the Midwestern United States for over a century. Despite the pre-mining history of the landscape as woodlands, spent surface coalfields are often reclaimed to grasslands. We assessed amphibian and reptile species on a large tract of coal spoil prairie and found 13 species of amphibians (nine frog and four salamander species) and 19 species of reptiles (one lizard, five turtle, and 13 snake species). Two state-endangered and three state species of special concern were documented. The amphibian diversity at our study site was comparable to the diversity found at a large restored prairie situated 175 km north, within the historic prairie peninsula.

  9. Chemical composition of spoil from bituminous coal and anthracite in Spain. Composicion quimica de los esteriles de hulla y antracita de Espana

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez Canibano, J; Fernandez Valcarce, A

    1991-05-01

    The article describes the chemical composition of spoil from bituminous coal and anthracite in Spain. Chemical composition, mineralogical properties and physical and mechanical characteristics are used to determine the most suitable application for the spoil in order to solve the problem of disposal. 20 refs., 5 figs., 4 tabs.

  10. Exact algebraization of the signal equation of spoiled gradient echo MRI

    Energy Technology Data Exchange (ETDEWEB)

    Dathe, Henning [Department of Orthodontics, Biomechanics Group, University Medical Centre, Goettingen (Germany); Helms, Gunther, E-mail: ghelms@gwdg.d [MR-Research in Neurology and Psychiatry, University Medical Centre, Goettingen (Germany)

    2010-08-07

    The Ernst equation for Fourier transform nuclear magnetic resonance (MR) describes the spoiled steady-state signal created by periodic partial excitation. In MR imaging (MRI), it is commonly applied to spoiled gradient-echo acquisition in the steady state, created by a small flip angle {alpha} at a repetition time TR much shorter than the longitudinal relaxation time T{sub 1}. We describe two parameter transformations of {alpha} and TR/T{sub 1}, which render the Ernst equation as a low-order rational function. Computer algebra can be readily applied for analytically solving protocol optimization, as shown for the dual flip angle experiment. These transformations are based on the half-angle tangent substitution and its hyperbolic analogue. They are monotonic and approach identity for small {alpha} and small TR/T{sub 1} with a third-order error. Thus, the exact algebraization can be readily applied to fast gradient echo MRI to yield a rational approximation in {alpha} and TR/T{sub 1}. This reveals a fundamental relationship between the square of the flip angle and TR/T{sub 1} which characterizes the Ernst angle, constant degree of T{sub 1}-weighting and the influence of the local radio-frequency field.

  11. Work plan, health and safety plan, and site characterization for the Rust Spoil Area (D-106)

    International Nuclear Information System (INIS)

    Bohrman, D.E.; Uziel, M.S.; Landguth, D.C.; Hawthorne, S.W.

    1990-06-01

    As part of the Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) of the Department of Energy's Y-12 Plant located in Oak Ridge, Tennessee, this work plan has been developed for the Rust Spoil Area (a solid waste disposal area). The work plan was developed by the Measurement Applications and Development Group (MAD) of the Health and Safety Research Division (HASRD) at Oak Ridge National Laboratory (ORNL) and will be implemented jointly by ORNL/MAD and the Y-12 Environmental Surveillance Section. This plan consists of four major sections: (1) a project description giving the scope and objectives of the investigation at the Rust Spoil Area; (2) field and sampling procedures describing sample documentation, soil sampling techniques, sample packaging and preservation, equipment decontamination, and disposal of investigation generated wastes; (3) sample analysis procedures detailing necessary analytical laboratory procedures to ensure the quality of chemical results from sample receipt through analysis and data reporting; and (4) a health and safety plan which describes general site hazards and particular hazards associated with specific tasks, assigns responsibilities, establishes personnel protection standards and mandatory safety procedures, and provides emergency information for contingencies that may arise during the course of field operations

  12. Biochar addition induced the same plant responses as elevated CO2 in mine spoil.

    Science.gov (United States)

    Zhang, Yaling; Drigo, Barbara; Bai, Shahla Hosseini; Menke, Carl; Zhang, Manyun; Xu, Zhihong

    2018-01-01

    Nitrogen (N) limitation is one of the major constrain factors for biochar in improving plant growth, the same for elevated atmospheric carbon dioxide (CO 2 ). Hence, we hypothesized that (1) biochar would induce the same plant responses as elevated CO 2 under N-poor conditions; (2) elevated CO 2 would decrease the potential of biochar application in improving plant growth. To test these hypotheses, we assessed the effects of pinewood biochar, produced at three pyrolytic temperatures (650, 750 and 850 °C), on C and N allocation at the whole-plant level of three plant species (Austrostipa ramossissima, Dichelachne micrantha and Isolepis nodosa) grown in the N poor mine spoil under both ambient (400 μL L -1 ) and elevated (700 μL L -1 ) CO 2 concentrations. Our data showed that biochar addition (1) significantly decreased leaf total N and δ 15 N (P < 0.05); (2) decreased leaf total N and δ 15 N more pronouncedly than those of root; and (3) showed more pronounced effects on improving plant biomass under ambient CO 2 than under elevated CO 2 concentration. Hence, it remained a strong possibility that biochar addition induced the same plant physiological responses as elevated CO 2 in the N-deficient mine spoil. As expected, elevated CO 2 decreased the ability of biochar addition in improving plant growth.

  13. Determination of soil mechanics of salt rock as a potential backfilling material in an underground repository

    International Nuclear Information System (INIS)

    Kappei, G.

    1987-09-01

    Within the framework of the research and development project 'Backfilling and sealing of boreholes, chambers and roadways in a final dump', the Institute for Underground Dumping chose - from the broad range of possible stowing materials - the material 'salt spoil' and investigated its soil-mechanical properties in detail. Besides the implementation of soil-mechanical standard analyses (determination of the grain size distribution, bulk density, limits of storage density, proctor density, permeabilities, and shear strength) of two selected salt spoils (heap salt and rock salt spoil), the studies concentrated on the determination of the compression behaviour of salt spoil. In order to obtain data on the compaction behaviour of this material in the case of increasing stress, compression tests with obstructed lateral expansion were carried out on a series of spoil samples differing mainly in the composition of grain sizes. In addition to this, for a small number of samples of rock salt spoil, the creep behaviour at constant stress was determined after the compaction phase. (orig./RB) [de

  14. Efficacy of Designer Biochars with or without Lime Application for Remediating Heavy Metals in Mine Spoil Soils

    Science.gov (United States)

    Sigua, Gilbert C.; Novak, Jeffrey; Johnson, Mark; Ippolito, James; Spokas, Kurt; Ducey, Thomas; Trippe, Kristin

    2017-04-01

    A multitude of research investigations have confirmed that biochars can increase soil carbon sequestration, improve critical plant nutrient concentrations, and improve the fertility, chemical, and physical properties of degraded agricultural soils. Recently, biochars ability to sequester metals has caught the attention of the mine reclamation sector. It is proposed that biochar is a suitable amendment to remediate heavy metals in mine spoils, as well as improve chemical conditions for enhanced plant growth. Better plant growth will improve phytostabilization, increase containment of metal-laden sediment, while also reducing potential metal uptake by plants. As such, utilization of a biochar with appropriate chemical and physical characteristics is crucial for effective binding of heavy metals while also improving plant growth conditions in mine spoils. Using two different mine spoils, we conducted laboratory and greenhouse experiments to determine the ability of designer biochar with or without lime application to favorably improve soil pH, reduce heavy metal bioavailability, and improve grass (e.g., wild blue rye) plant nutrient uptake. Preliminary results showed that our designer biochars did increase pH of acid mine spoils significantly (pheavy metals (e.g. aluminum, chromium, zinc, nickel, zinc, manganese, copper and cadmium) in the soils.

  15. Remediation of an acidic mine spoil: Miscanthus biochar and lime amendment affects metal availability, plant growth, and soil enzyme activity.

    Science.gov (United States)

    Novak, Jeffrey M; Ippolito, James A; Ducey, Thomas F; Watts, Donald W; Spokas, Kurt A; Trippe, Kristin M; Sigua, Gilbert C; Johnson, Mark G

    2018-08-01

    Biochar may be a tool for mine spoil remediation; however, its mechanisms for achieving this goal remain unclear. In this study, Miscanthus (Miscanthus giganteus) biochar was evaluated for its ability to reclaim acidic mine spoils (pH lime/no lime and fertilizer additions. Blue Wildrye (Elymus glaucus cv. 'Elkton') was planted and later the shoots and roots were collected and metal concentrations determined. Afterwards, each pot was leached with deionized water, and the leachate analyzed for pH, electrical conductivity (EC), dissolved organic carbon (DOC) and soluble metal concentrations. After drying, the spoil was extracted with 0.01 M CaCl 2 and Mehlich 3 (M3) to determine extractable Al, Cu, and Zn concentrations. Additionally, microbial activity was measured using a fluorescent β-glucosidase and N-acetyl-β-d-glucosaminidase assay. Spoil treated with lime and biochar had significantly greater pH and EC values. Significantly greater β-glucosidase activity occurred only in the 5% biochar plus lime treatment, while N-acetyl-β-d-glucosaminidase activities were not altered. Metal concentrations in rye shoot and roots were mixed. Lime additions significantly reduced extractable metal concentrations. Increasing biochar rates alone significantly reduced leachate DOC concentrations, and subsequently reduced leachable metal concentrations. Surprisingly, miscanthus biochar, by itself, was limited at mitigation, but when combined with lime, the combination was capable of further reducing extractable metal concentrations and improving β-glucosidase enzyme activity. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

  16. Effect of biotic and abiotic factors on soil microbial community diversity during primary succession on colliery spoil heaps

    Czech Academy of Sciences Publication Activity Database

    Elhottová, Dana; Frouz, Jan; Chroňáková, Alica; Malý, S.; Krištůfek, Václav; Kalčík, Jiří; Szili-Kovács, T.; Picek, T.

    2004-01-01

    Roč. 45, - (2004), s. 51 ISSN 0009-0646. [Kongres československé společnosti mikrobiologické /23./. 06.09.2004-09.09.2004, Brno] Keywords : soil microbial community * primary succession * colliery spoil heaps Subject RIV: EH - Ecology, Behaviour

  17. Colonization of colliery spoil heaps by millipedes (Diplopoda) and terrestrial isopods (Oniscidea) in the Sokolov region, Czech Republic

    Czech Academy of Sciences Publication Activity Database

    Tajovský, Karel

    2001-01-01

    Roč. 9, č. 4 (2001), s. 365-369 ISSN 1061-2971 Institutional research plan: CEZ:AV0Z6066911 Keywords : colliery spoil heaps * succession * rekultivation Subject RIV: EH - Ecology, Behaviour Impact factor: 1.011, year: 2001

  18. Associations of dominant plant species with arbuscular mycorrhizal fungi during vegetation development on coal mine spoil banks

    Energy Technology Data Exchange (ETDEWEB)

    Rydlova, J.; Vosatka, M. [Academy of Science. Pruhonice (Czech Republic). Inst. of Botany

    2001-07-01

    Among plants colonizing mine spoil banks in Northern Bohemia the first colonizers, mainly ruderal annuals from Chenopodiaceae and Brassicaceae were found not to be associated with arbuscular mycorrhizal fungi (AMF). These species cultivated in pots with soil from four sites in different succession stages of the spoil bank did not respond to the presence of native or non-native AMF. All grass species studied (Elytrigia repens, Calamagrostis epigejos and Arrhenatherum elatius) were found moderately colonized in the field. Carduus acanthoides was found to be highly colonized in the field; however, it did not show growth response to AMF in the pot experiment. The AMF native in four sites on the spoil banks showed high infectivity but low effectiveness in association with colonizing plants compared to the non-native isolate G. fistulosum BEG23. In general, dependence on AMF in the cultivation experiment was rather low, regardless of the fact that plants were found to be associated with AMF either in the field or in pots. Occurrence and effectiveness of mycorrhizal associations might relate primarily to the mycotrophic status of each plant species rather than to the age of the spoil bank sites studied.

  19. Spoiling of radiation zeros at the one-loop level and infrared finiteness

    International Nuclear Information System (INIS)

    Laursen, M.L.; Samuel, M.A.; Sen, A.

    1983-01-01

    We consider the amplitude for the radiative decay W - →phi 1 phi 2 #betta# (scalar quarks) including one-loop gluon corrections. We study this process to see if the amplitude (radiation) zeros found in lowest order survive at the one-loop level. The subset of diagrams containing self-mass insertions preserves the zero. Seagull types are shown to have a violation which is similar to kappanot =1. Triangle and box diagrams spoil the zeros as they do in the case of a scalar W. However, the amplitude is completely free of any mass singularities in the classical null zone. We conjecture that this will remain true for spin-(1/2) quarks

  20. Stillbirth and stigma: the spoiling and repair of multiple social identities.

    Science.gov (United States)

    Brierley-Jones, Lyn; Crawley, Rosalind; Lomax, Samantha; Ayers, Susan

    This study investigated mothers' experiences surrounding stillbirth in the United Kingdom, their memory making and sharing opportunities, and the effect these opportunities had on them. Qualitative data were generated from free text responses to open-ended questions. Thematic content analysis revealed that "stigma" was experienced by most women and Goffman's (1963) work on stigma was subsequently used as an analytical framework. Results suggest that stillbirth can spoil the identities of "patient," "mother," and "full citizen." Stigma was reported as arising from interactions with professionals, family, friends, work colleagues, and even casual acquaintances. Stillbirth produces common learning experiences often requiring "identity work" (Murphy, 2012). Memory making and sharing may be important in this work and further research is needed. Stigma can reduce the memory sharing opportunities for women after stillbirth and this may explain some of the differential mental health effects of memory making after stillbirth that is documented in the literature.

  1. An experimental study on dredge spoil of estuarine sediments in the bay of seine (France): A morphosedimentary assessment

    Science.gov (United States)

    Marmin, Stella; Lesueur, Patrick; Dauvin, Jean Claude; Samson, Sandrine; Tournier, Patrice; Gallicher Lavanne, Albert; Dubrulle-Brunaud, Carole; Thouroude, Coralie

    2016-03-01

    Studies on the consequences of dredging on estuarine morphology and its sedimentary dynamics are common, but the impacts of dumping dredge spoil in coastal open settings are rarely found in scientific literature. An experimental study was conducted over the period 2012-2013 to monitor the physical impacts of dredged material dumped at two adjacent sites (one million cubic metres at each) on the inner shelf of the Bay of Seine in France (eastern part of the English Channel, La Manche). As recently reinforced in the EU Marine Strategy Framework Directive (MSFD), knowledge on the location and intensity of human impacts (e.g. on marine ecosystems) is critical for effective marine management and conservation. So, two methods of disposition were tested to evaluate the impacts of dumping on the environment and thus propose recommendations for future dumping. The strategy is based on a Before-After-Control-Impact (BACI) approach, in which the spatio-temporal variability was studied by analysing the morphological and sedimentological characteristics over a period of 28 months, from November 2011 to April 2014, also including recovery of the seafloor after cessation of the dumping activities. The first experimental dumping operation (MASED) was carried out regularly for 8 months at a single point and generating a conical deposit of 5 m in height, while the second dumping (MABIO) lasted for 12 months involving four steps in the dumping process. In the second case, a wider area was covered, leading to the formation of a smaller deposit of 2 m in height. The dumped deposits consisted of muddy fine sand, whereas the inner shelf seafloor in this area is covered with fine to medium sand. As a result, muddy fine sand accumulated at or near the two dumping sites, with a maximum mud (i.e. particles4 Φ) content of 50% compared todredged material remained at the end of the dumping periods. After dumping ceased, a further 5% of material for MABIO and 20% for MASED, was transported out

  2. Hydrological remedial actions for polluted overburden dumps, spoils and landfills. Papers and posters; Wasserwirtschaftliche Sanierung von Bergbaukippen, Halden und Deponien. Vortraege und Posterbeitraege

    Energy Technology Data Exchange (ETDEWEB)

    Pohl, A. [ed.; Haefner, F.; Schmidt, J.; Merkel, B. [comps.

    2000-07-01

    This publication contains the papers and posters presented at the conference 'Hydrological remedial actions for polluted overburden dumps, spoils and landfills. 35 Papers have been recorded as separate citations in this database.

  3. Generating femtosecond X-ray pulses using an emittance-spoiling foil in free-electron lasers

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Y., E-mail: ding@slac.stanford.edu; Coffee, R.; Decker, F.-J.; Emma, P.; Field, C.; Huang, Z.; Krejcik, P.; Krzywinski, J.; Loos, H.; Lutman, A.; Marinelli, A.; Maxwell, T. J.; Turner, J. [SLAC National Accelerator Laboratory, Menlo Park, California 94025 (United States); Behrens, C. [Deutsches Elektronen-Synchrotron DESY, Notkestr. 85, 22607 Hamburg (Germany); Helml, W. [Technische Universität München, James-Franck-Straße 1, 85748 Garching (Germany)

    2015-11-09

    Generation of femtosecond to sub-femtosecond pulses is attracting much attention in X-ray free-electron laser user community. One method is to use a slotted, emittance-spoiling foil which was proposed before (P. Emma et al., Phys. Rev. Lett. 92, 074801 (2004)) and has been widely used at the Linac Coherent Light Source. Direct experimental characterization of the slotted-foil performance was previously unfeasible due to a lack of appropriate diagnostics. With a recently installed X-band radio-frequency transverse deflector, we are able to characterize the electron bunch spoiling effect and X-ray pulse when using the slotted foil. We show that few-femtosecond X-ray pulses are generated with flexible control of the single-pulse duration or double-pulse separation with comparison to the theoretical model.

  4. Materialism.

    Science.gov (United States)

    Melnyk, Andrew

    2012-05-01

    Materialism is nearly universally assumed by cognitive scientists. Intuitively, materialism says that a person's mental states are nothing over and above his or her material states, while dualism denies this. Philosophers have introduced concepts (e.g., realization and supervenience) to assist in formulating the theses of materialism and dualism with more precision, and distinguished among importantly different versions of each view (e.g., eliminative materialism, substance dualism, and emergentism). They have also clarified the logic of arguments that use empirical findings to support materialism. Finally, they have devised various objections to materialism, objections that therefore serve also as arguments for dualism. These objections typically center around two features of mental states that materialism has had trouble in accommodating. The first feature is intentionality, the property of representing, or being about, objects, properties, and states of affairs external to the mental states. The second feature is phenomenal consciousness, the property possessed by many mental states of there being something it is like for the subject of the mental state to be in that mental state. WIREs Cogn Sci 2012, 3:281-292. doi: 10.1002/wcs.1174 For further resources related to this article, please visit the WIREs website. Copyright © 2012 John Wiley & Sons, Ltd.

  5. Do Attitudes About Spoiling Children Affect Attitudes Regarding What Infants Need for Early Social-Emotional Development

    OpenAIRE

    Westover, Kathleen

    2012-01-01

    Secure infant attachment is important for the positive social-emotional development of children. Many parents have limited understanding of social-emotional development and the influence of appropriate responsive parenting behaviors to their infants’ cues. For example, many parents believe you can spoil an infant if you pick them up every time they cry. Researchers study the impact of positive responses to infants’ cues. Infants form a more secure attachment and learn to interpret the world a...

  6. Assessment of biochar and iron filing amendments for the remediation of a metal, arsenic and phenanthrene co-contaminated spoil

    International Nuclear Information System (INIS)

    Sneath, Helen E.; Hutchings, Tony R.; Leij, Frans A.A.M. de

    2013-01-01

    Sites contaminated with mixtures of metals, metalloids and organics are difficult to remediate as each contaminant type may require a different treatment. Biochar, with high metal sorption capacity, used singly and in combination with iron filings, is investigated in microcosm trials to immobilise metal(loid)s within a contaminated spoil, thereby enabling revegetation and degradation of organic pollutants. A mine spoil, contaminated with heavy metals, arsenic and spiked with phenanthrene was treated with either 1%w/w biochar, 5%w/w iron or their combination, enhancing phenanthrene degradation by 44–65%. Biochar treatment reduced Cu leaching and enabled sunflower growth, but had no significant effect on As mobility. Iron treatment reduced Cu and As leaching but negatively impacted soil structure and released high levels of Fe causing sunflower plant mortality. The combined treatment reduced both Cu and As leaching and enabled sunflower growth suggesting this could be a useful approach for treating co-contaminated sites. -- Highlights: ► 56 day microcosm trials examine biochar for remediation of co-contaminated sites. ► Biochar reduces leachable Cu concentrations but phytotoxicity remains. ► Iron filings are investigated as a co-amendment with biochar to reduce As leaching. ► Removal of metal toxicity stimulates phenanthrene degradation. ► Biochar could enable revegetation of contaminated sites. -- Biochar and iron filings incorporated into contaminated spoils reduce Cu and As leaching and stimulate phenanthrene degradation, but do not prevent phytotoxicity to sunflowers

  7. Thermal inactivation of polyphenoloxidase and peroxidase in Jubileu clingstone peach and yeast isolated from its spoiled puree

    Directory of Open Access Journals (Sweden)

    Andréa Menezes Lopes

    2014-03-01

    Full Text Available The thermal inactivation of yeast isolated from spoiled Jubileu peach puree and that of polyphenoloxidase (PPO and peroxidase (POD in cv. Jubileu, which is widely cultivated in southern Rio Grande do Sul state, Brazil, were studied. PPO and POD were extracted using the protein powder method and submitted to partial purification by precipitation followed by dialysis. The enzymatic activity was determined measuring the increase in absorbance at 420 nm for PPO and 470 nm for POD. The yeast used in this investigation was isolated from spoiled Jubileu peach puree at 22 °Brix, with total initial microbial count of 22 × 10² UFCmL- 1. Stock cultures were maintained on potato dextrose agar (PDA slants at 4 °C and pH 5 for later use for microbial growth. In all cases, kinetic analysis of the results suggests that the thermal inactivation was well described by a first-order kinetic model, and the temperature dependence was significantly represented by the Arrhenius law. Both enzymes were affected by heat denaturation, and PPO was more thermostable. PPO was also more thermosTable than the yeast isolated from peach puree. The D60-values were 1.53 and 1.87 min for PPO and yeast isolated from spoiled Jubileu peach puree, respectively.

  8. Response surface optimization of biosurfactant produced by Pseudomonas aeruginosa MA01 isolated from spoiled apples.

    Science.gov (United States)

    Abbasi, Habib; Sharafi, Hakimeh; Alidost, Leila; Bodagh, Atefe; Zahiri, Hossein Shahbani; Noghabi, Kambiz Akbari

    2013-01-01

    A potent biosurfactant-producing bacterial strain isolated from spoiled apples was identified by 16S rRNA as Pseudomonas aeruginosa MA01. Compositional analysis revealed that the extracted biosurfactant was composed of high percentages of lipid (66%, w/w) and carbohydrate (32%, w/w). The surface tension of pure water decreased gradually with increasing biosurfactant concentration to 32.5 mN m(-1) with critical micelle concentration (CMC) value of 10.1 mg L(-1). The Fourier transform infrared spectrum of extracted biosurfactant confirmed the glycolipid nature of this natural product. Response surface methodology (RSM) was employed to optimize the biosynthesis medium for the production of MA01 biosurfactant. Nineteen carbon sources and 11 nitrogen sources were examined, with soybean oil and sodium nitrate being the most effective carbon and nitrogen sources on biosurfactant production, respectively. Among the organic nitrogen sources examined, yeast extract was necessary as a complementary nitrogen source for high production yield. Biosurfactant production at the optimum value of fermentation processing factor (15.68 g/L) was 29.5% higher than the biosurfactant concentration obtained before the RSM optimization (12.1 g/L). A central composite design algorithm was used to optimize the levels of key medium components, and it was concluded that two stages of optimization using RSM could increase biosurfactant production by 1.46 times, as compared to the values obtained before optimization.

  9. Identifying yeast isolated from spoiled peach puree and assessment of its batch culture for invertase production

    Directory of Open Access Journals (Sweden)

    Marcela Vega FERREIRA

    Full Text Available Abstract The identification of yeasts isolated from spoiled Jubileu peach puree using the API 20C AUX method and a commercial yeast as witness were studied. Subsequently, the yeast’s growth potential using two batch culture treatments were performed to evaluate number of colonies (N, reducing sugar concentration (RS, free-invertase (FI, and culture-invertase activity (CI. Stock cultures were maintained on potato dextrose agar (PDA slants at 4 °C and pH 5 for later use for batch-culture (150 rpm at 30°C for 24 h, then they were stored at 4 °C for subsequent invertase extraction. The FI extract was obtained using NaHCO3 as autolysis agent, and CI activity was determined on the supernatant after batch-cultured centrifugation. The activity was followed by an increase in absorbance at 490 nm using the acid 3,5-DNS method with glucose standard. Of the four yeasts identified, Saccharomyces cerevisiae was chosen for legal reasons. It showed logarithmic growth up to 18 h of fermentation with positive correlation CI activity and inverse with RS. FI showed greater activity by the end of the log phase and an inverse correlation with CI activity. Finally, it was concluded that treatment “A” is more effective than “B” to produce invertase (EC 3.2.1.26.

  10. Topography of Spoil Heaps and Its Role in Plant Succession and Soil Fauna Presence

    Directory of Open Access Journals (Sweden)

    Walmsley A.

    2017-03-01

    Full Text Available The spoil heaps from brown coal mining without technical reclamation are interesting specific sites for ecological relationships observation. This research was aimed at investigating whether topographic features, which determine soil nutrient and moisture distribution, in combination with soil fauna (wireworm and earthworm presence, affect plant community composition at a spontaneously revegetated post mining area with an undulating surface. Two sites of different age with three types of topographic features were selected, soil moisture and nutrient contents were measured, and plant community composition and soil macrofauna community were sampled at each position. Wireworms were present at all positions and were most abundant at the bottoms of waves at the younger site; their presence was correlated with the presence of several plant species with high palatability for wireworms, but the direction of the interaction is not clear. Earthworms were only present at the older site and had the highest abundance at flat sections. Earthworm presence affected the amount of nitrogen in soil - the highest nitrogen content was at the site with the highest earthworm density and was followed by a higher diversity of plant community. The plant community composition was generally correlated with plant available nutrient content - especially P and N. We infer that topographic features affect nutrient and soil fauna distribution, which consequently influences the plant community composition.

  11. Perspective on China's one-child family policy: spoiled children? Questions and responses.

    Science.gov (United States)

    Wyner, N B

    1987-01-01

    China's 1-child policy has been effective in its objective of limiting population growth, yet the policy never has been imposed rigidly. For example, the policy is less restrictive in rural areas where 80% of the population live. It is argued the workers in the countryside need larger families for production. Between 1986-87, China's birthrate increased from 18/1000 - 21/1000, suggesting an easing of policy restrictions. Some population experts maintain that population increase is not a major problem as long as gross income figures continue to exceed the growth of population. Others indicate that a renewed emphasis on small families may be necessary. Some planners have observed developmental dynamics that have serious implications for traditional social and family values. 1 mental health expert has identified the "spoiled child syndrome," noting that the child in the 1- child family seems to be more dependent, less able to take care of himself/herself, more self-centered yet has a higher intelligence quotient. Parent training classes are now being developed.

  12. Vertical distribution and temperature relations of sheathing mycorrhizas of Betula spp. growing on coal spoil

    Energy Technology Data Exchange (ETDEWEB)

    Ingleby, K.; Last, F.T.; Mason, P.A.

    1985-10-01

    Naturally-occurring fine roots (<2 mm dia.) of Betula spp. were sampled to a depth of 30 cm at seven locations on each of two transects across a heap of coal spoil in parts subject to after-burn. In the top 20 cm of substrate, 87% of the root pieces occurred. Irrespective of depth, sheathing mycorrhizas were found on 83% of the roof pieces. While the percentages of Paxillus-type mycorrhizas decreased with soil depth, those of a Scleroderma-type significantly increased. Total numbers of mycorrhizas counted at the end-of-season were independent of substrate temperatures. However, numbers of Paxillus-type mycorrhizas were inversely related to both annual mean and spring substrate temperatures, whereas those of the Scleroderma- type were directly related. Vegetative cultures of Scleroderma citrinum grew on an agar medium at 30 C, whereas those of Paxillus involutus did not; at lower temperatures the two fungi responded similarly to temperature changes. The evidence suggests that the observed patterns of mycorrhizal development reflect the changing competitive abilities of Scleroderma and Paxillus and/or host influences at different temperatures in the range 8-16 C.

  13. Parameter Optimization for Quantitative Signal-Concentration Mapping Using Spoiled Gradient Echo MRI

    Directory of Open Access Journals (Sweden)

    Gasser Hathout

    2012-01-01

    Full Text Available Rationale and Objectives. Accurate signal to tracer concentration maps are critical to quantitative MRI. The purpose of this study was to evaluate and optimize spoiled gradient echo (SPGR MR sequences for the use of gadolinium (Gd-DTPA as a kinetic tracer. Methods. Water-gadolinium phantoms were constructed for a physiologic range of gadolinium concentrations. Observed and calculated SPGR signal to concentration curves were generated. Using a percentage error determination, optimal pulse parameters for signal to concentration mapping were obtained. Results. The accuracy of the SPGR equation is a function of the chosen MR pulse parameters, particularly the time to repetition (TR and the flip angle (FA. At all experimental values of TR, increasing FA decreases the ratio between observed and calculated signals. Conversely, for a constant FA, increasing TR increases this ratio. Using optimized pulse parameter sets, it is possible to achieve excellent accuracy (approximately 5% over a physiologic range of concentration tracer concentrations. Conclusion. Optimal pulse parameter sets exist and their use is essential for deriving accurate signal to concentration curves in quantitative MRI.

  14. Materials

    CSIR Research Space (South Africa)

    Van Wyk, Llewellyn V

    2009-02-01

    Full Text Available . It is generally included as part of a structurally insulated panel (SIP) where the foam is sandwiched between external skins of steel, wood or cement. Cement composites Cement bonded composites are an important class of building materials. These products... for their stone buildings, including the Egyptians, Aztecs and Inca’s. As stone is a very dense material it requires intensive heating to become warm. Rocks were generally stacked dry but mud, and later cement, can be used as a mortar to hold the rocks...

  15. Formulation of an organic carbon trajectory over a 10-year period on a restored spoil island in south-central Florida

    Science.gov (United States)

    Schafer, T.; Ellis, R.; Osborne, T.; Hicks Pries, C.

    2015-12-01

    Long-term monitoring of restoration projects aims to determine long-term sustainability and stability of restored systems. In coastal wetlands, one indicator of restoration of ecosystem function can be seen with organic matter (specifically carbon) accretion. SL-15, a spoil island in Fort Pierce, Fl was restored in 2005, and has been monitored for return to natural condition over the last 10 years.. To assess sediment carbon accretion, sediment cores were collected in a set of eight plots, located on the SL-15 mangrove island and the surrounding seagrass recruitment area. These were analyzed for organic carbon, microbial biomass carbon, extractable carbon, and total nitrogen. The biogeochemical data collected in the previous year was compared to data collected in 2005-2007. Vegetation surveys were also completed to show the build-up of organic material in accordance with vegetation shift over the 9-year period. From this information, a trajectory has been formulated on organic carbon accretion and vegetation shift from the time of orginal restoration activities. By comparison to control sites nearby, realistic estimates of time required to reach natural levels of carbon and vegetation community structure can be calculated..

  16. Copper-adapted Suillus luteus, a symbiotic solution for pines colonizing Cu mine spoils.

    Science.gov (United States)

    Adriaensen, K; Vrålstad, T; Noben, J-P; Vangronsveld, J; Colpaert, J V

    2005-11-01

    Natural populations thriving in heavy-metal-contaminated ecosystems are often subjected to selective pressures for increased resistance to toxic metals. In the present study we describe a population of the ectomycorrhizal fungus Suillus luteus that colonized a toxic Cu mine spoil in Norway. We hypothesized that this population had developed adaptive Cu tolerance and was able to protect pine trees against Cu toxicity. We also tested for the existence of cotolerance to Cu and Zn in S. luteus. Isolates from Cu-polluted, Zn-polluted, and nonpolluted sites were grown in vitro on Cu- or Zn-supplemented medium. The Cu mine isolates exhibited high Cu tolerance, whereas the Zn-tolerant isolates were shown to be Cu sensitive, and vice versa. This indicates the evolution of metal-specific tolerance mechanisms is strongly triggered by the pollution in the local environment. Cotolerance does not occur in the S. luteus isolates studied. In a dose-response experiment, the Cu sensitivity of nonmycorrhizal Pinus sylvestris seedlings was compared to the sensitivity of mycorrhizal seedlings colonized either by a Cu-sensitive or Cu-tolerant S. luteus isolate. In nonmycorrhizal plants and plants colonized by the Cu-sensitive isolate, root growth and nutrient uptake were strongly inhibited under Cu stress conditions. In contrast, plants colonized by the Cu-tolerant isolate were hardly affected. The Cu-adapted S. luteus isolate provided excellent insurance against Cu toxicity in pine seedlings exposed to elevated Cu levels. Such a metal-adapted Suillus-Pinus combination might be suitable for large-scale land reclamation at phytotoxic metalliferous and industrial sites.

  17. Dynamic MR imaging of the temporomandibular joint arthrosis using spoiled GRASS sequence

    Energy Technology Data Exchange (ETDEWEB)

    Suenaga, Shigeaki; Hamamoto, Sadatoshi; Kawano, Kazunori (Kagoshima Univ. (Japan). Dental School) (and others)

    1994-07-01

    The purpose of this study was to quantitatively evaluate contrast enhancement effects of the posterior disk attachment in the temporomandibular joint arthrosis using dynamic MRI with bilateral surface coils. One hundred twenty-four temporomandibular joints in 96 symptomatic patients and 27 control subjects were examined with a spoiled GRASS pulse sequence (TR: 35 ms, TE: 8 ms, flip angle: 60deg). One sagittal scan was performed prior to injection, then 0.1 mmol/kg of Gd-DTPA was given as a rapid bolus injection, immediately after which scans were performed at 30 seconds intervals for a period of 5 minutes. Signal intensity (SI) was measured from the ROI of the posterior disk attachment region. The contrast enhancement effects may be calculated by SI ratio (SIR) = ( SI[sup post]-SI[sup pre])/SI[sup pre], where SI[sup post] and SI[sup pre] were the signal intensities after and before administration of contrast medium. The time intensity curve of SIR versus time after injection was obtained on each symptoms. Join pain group (85 joints) tended to show a rapid enhancement pattern, while control group (54 joints), joint sound or opening limitation group (39 joints), and asymptomatic group (68 joints) showed a relatively gradual enhancement pattern. The drop of SIR in four groups were hardly observed during examination. Mean peak SIR of control group, joint pain group, joint sound or opening limitation group, and asymptomatic group was 0.62[+-]0.24 (SD), 1.53[+-]0.69, 0.73[+-]0.38 and 0.78[+-]0.44 respectively. The mean SIR of pain group was significantly (P<0.001, t-test) higher than that of other groups. These results suggested that dynamic MRI of the temporomandibular joint may effectively depict the inflammatory changes of the posterior disk attachment. (author).

  18. Dynamic MR imaging of the temporomandibular joint arthrosis using spoiled GRASS sequence

    International Nuclear Information System (INIS)

    Suenaga, Shigeaki; Hamamoto, Sadatoshi; Kawano, Kazunori

    1994-01-01

    The purpose of this study was to quantitatively evaluate contrast enhancement effects of the posterior disk attachment in the temporomandibular joint arthrosis using dynamic MRI with bilateral surface coils. One hundred twenty-four temporomandibular joints in 96 symptomatic patients and 27 control subjects were examined with a spoiled GRASS pulse sequence (TR: 35 ms, TE: 8 ms, flip angle: 60deg). One sagittal scan was performed prior to injection, then 0.1 mmol/kg of Gd-DTPA was given as a rapid bolus injection, immediately after which scans were performed at 30 seconds intervals for a period of 5 minutes. Signal intensity (SI) was measured from the ROI of the posterior disk attachment region. The contrast enhancement effects may be calculated by SI ratio (SIR) = ( SI post -SI pre )/SI pre , where SI post and SI pre were the signal intensities after and before administration of contrast medium. The time intensity curve of SIR versus time after injection was obtained on each symptoms. Join pain group (85 joints) tended to show a rapid enhancement pattern, while control group (54 joints), joint sound or opening limitation group (39 joints), and asymptomatic group (68 joints) showed a relatively gradual enhancement pattern. The drop of SIR in four groups were hardly observed during examination. Mean peak SIR of control group, joint pain group, joint sound or opening limitation group, and asymptomatic group was 0.62±0.24 (SD), 1.53±0.69, 0.73±0.38 and 0.78±0.44 respectively. The mean SIR of pain group was significantly (P<0.001, t-test) higher than that of other groups. These results suggested that dynamic MRI of the temporomandibular joint may effectively depict the inflammatory changes of the posterior disk attachment. (author)

  19. Remedial Investigation Report on Bear Creek Valley Operable Unit 2 (Rust Spoil Area, Spoil Area 1, and SY-200 Yard) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. Volume 1, Main text

    International Nuclear Information System (INIS)

    1995-01-01

    This report on the BCV OU 2 at the Y-12 Plant, was prepared in accordance with requirements under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) for reporting the results of a site characterization for public review. It provides the Environmental Restoration Program with information about the results of the 1993 investigation. It includes information on risk assessments that have evaluated impacts to human health and the environment. Field activities included collection of subsurface soil samples, groundwater and surface water samples, and sediments and seep at the Rust Spoil Area (RSA), SY-200 Yard, and SA-1

  20. Remedial Investigation Report on Bear Creek Valley Operable Unit 2 (Rust Spoil Area, Spoil Area 1, and SY-200 Yard) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. Volume 1, Main text

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-01-01

    This report on the BCV OU 2 at the Y-12 Plant, was prepared in accordance with requirements under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) for reporting the results of a site characterization for public review. It provides the Environmental Restoration Program with information about the results of the 1993 investigation. It includes information on risk assessments that have evaluated impacts to human health and the environment. Field activities included collection of subsurface soil samples, groundwater and surface water samples, and sediments and seep at the Rust Spoil Area (RSA), SY-200 Yard, and SA-1.

  1. Coal Mining Spoil Heap Management as urban solid waste dump; Utilizacion de Escombreras de Carbon como Vertedero Controlado de Residuos Solidos Urbanos

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    In the coordinated project DISPOSAL OF SOLID RESIDUES FROM COAL it is included the project Coal Mining Spoil Heap Management as Urban Solid Waste Dump. The main target of this project consisted of determining the viability of using coal mining spoil heaps, as controlled dubbish dump of urban solid wastes. The working plan to achieve this objective was composed of the following stages: 1. Urban solid wastes characterization. 2. Methodology to be followed for the selection of coal mining spoil heaps as controlled dump of urban solid wastes. 2.1 Classification and preliminary assessment of the possibility of using spoil heaps as urban solid waste dumps (APT/NON APT). 2.2 Realization of geological, geotechnical, hydrogeological and environmental studies applied to the spoil heaps classified as APT. 2.3 Analysis of the compatibility of the mining activity with the urban solid wastes dumped on the spoil heap. 2.4 Analysis of the use of coal mining wastes in the rubbish dump operative life. 3. Extraction of conclusions. The works were focused in the Leon province. As result of the researches we obtained the following results and conclusions: In the areas studied, only two emplacements are optima to dump urban solid wastes; spoil heap n. 13. Roguera Mine (Cinera-Matallana) and the open pit mine n. 4, Las Chaviadas, in Villablino. The active spoil heap use as controlled rubbish dump can cause, if not managed adequately, several coperating and occupational problems to the mine and to the company that manages the urban solid wastes. The abandoned spoil heap utilisation is difficult due to the problems that would arise when conditioning the site to be use as rubbish dump. The use of abandoned open pit mines, as controlled rubbish dump is feasible if geological, geotechnical, hydrogeological and environmental studies support it. It's possible the use of the coal mining wastes in the different operatives phases of the controlled rubbish dump. The evaluation methodology

  2. Coal Mining Spoil Heap Management as urban solid waste dump; Utilizacion de Escombreras de Carbon como Vertedero Controlado de Residuos Solidos Urbanos

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    In the coordinated project DISPOSAL OF SOLID RESIDUES FROM COAL it is included the project Coal Mining Spoil Heap Management as Urban Solid Waste Dump. The main target of this project consisted of determining the viability of using coal mining spoil heaps, as controlled dubbish dump of urban solid wastes. The working plan to achieve this objective was composed of the following stages: 1. Urban solid wastes characterization. 2. Methodology to be followed for the selection of coal mining spoil heaps as controlled dump of urban solid wastes. 2.1 Classification and preliminary assessment of the possibility of using spoil heaps as urban solid waste dumps (APT/NON APT). 2.2 Realization of geological, geotechnical, hydrogeological and environmental studies applied to the spoil heaps classified as APT. 2.3 Analysis of the compatibility of the mining activity with the urban solid wastes dumped on the spoil heap. 2.4 Analysis of the use of coal mining wastes in the rubbish dump operative life. 3. Extraction of conclusions. The works were focused in the Leon province. As result of the researches we obtained the following results and conclusions: In the areas studied, only two emplacements are optima to dump urban solid wastes; spoil heap n. 13. Roguera Mine (Cinera-Matallana) and the open pit mine n. 4, Las Chaviadas, in Villablino. The active spoil heap use as controlled rubbish dump can cause, if not managed adequately, several coperating and occupational problems to the mine and to the company that manages the urban solid wastes. The abandoned spoil heap utilisation is difficult due to the problems that would arise when conditioning the site to be use as rubbish dump. The use of abandoned open pit mines, as controlled rubbish dump is feasible if geological, geotechnical, hydrogeological and environmental studies support it. It's possible the use of the coal mining wastes in the different operatives phases of the controlled rubbish dump. The evaluation methodology developed

  3. Chemical and isotopic tracing of underground water in relation with leaching of mine spoils, Nord-Pas-de-Calais Coal Basin (France)

    International Nuclear Information System (INIS)

    Denimal, S.; Tribovillard, N.; Meilliez, F.; Barbecot, F.; Dever, L.

    2001-01-01

    Coal mining activity in the Nord-Pas-de-Calais region (Northern France) has generated many mine spoils. The oxidation of the pyrite content of such coal shales and their leaching can be a source of sulfate pollution for the underlying chalk aquifer, i.e. the main drinking water resource of the region. Two sites of study have been retained: one in the free water table zone and the other in the confined water table zone. Samples from both mine spoils have been analyzed with respect to their carbon and sulfur content and a superficial leaching of these elements has been evidenced. Water has been sampled in piezometers and boreholes close to the mine spoils and also along natural flux lines. The use of sulfur isotopes as markers of the different sulfate sources has confirmed the spoils source but has permitted to identify another source in the second site which is the Tertiary gypsum-bearing Ostricourt sands. This study has shown also that in the confined water table zone, part of the exported sulfates is reduced. This bacterial reduction of sulfates is due to a joint leaching of both carbon and sulfur in the mine spoils. A self-purification phenomenon occurs when the chalk aquifer is confined beneath the Cenozoic cover. (J.S.)

  4. Bioavailability and microbial adaptation to elevated levels of uranium in an acid, organic topsoil forming on an old mine spoil

    International Nuclear Information System (INIS)

    Joner, E.J.; Munier-Lamy, C.; Gouget, B.

    2007-01-01

    An old mine spoil at a 19. century mining site with considerable residues of uranium (400-800 mg U/kg) was investigated with respect to U concentrations in soil and plants and tolerance to U in the soil microbial community in order to describe the bioavailability of U. Measurements of soil fractions representing water-soluble U, easily exchangeable U, and U bound to humidified organic matter showed that all fractions contained elevated concentrations of U. Plant U concentrations were only 10 times higher at the mine spoil site compared to the reference site (3 mg U/kg vs 0.3 mg U/kg), while the most easily available soil fractions contained 0.18 to 0.86 mg U/kg soil at the mine spoil. An eco-toxicity bioassay using incorporation of [ 3 H]thymidine into the indigenous microbial communities of the two soils in the presence of increasing U concentrations showed that microorganisms at the mining site were sensitive to U but also that they had acquired a substantial tolerance toward U (EC50, the effective concentration reducing activity by 50% of UO 2 -citrate was similar to 120 μM as compared to 30 μM in the reference soil). In the assay, more than 40% of the microbial activity was maintained in the presence of 1 mM UO 2 -citrate versus 3% in the reference soil. We conclude that U-enriched mining waste can contain sufficiently elevated concentrations of bio-available U to affect indigenous microorganisms and that bio-available U imposes a selection pressure that favors the development of a highly uranium-tolerant microbial community, while plant uptake of U remains low. (authors)

  5. Bioavailability and microbial adaptation to elevated levels of uranium in an acid, organic topsoil forming on an old mine spoil

    Energy Technology Data Exchange (ETDEWEB)

    Joner, E.J. [BIOFORSK, Soil and Environm Div, N-1432 As, (Norway); Munier-Lamy, C. [Univ Nancy 1, Fac Sci, Natl Ctr Rech Sci, Unit Mixte Rech 7137 LIMOS, F-54506 Vandoeuvre Les Nancy, (France); Gouget, B. [CEA Saclay, Lab Pierre Sue, F-91191 Gif Sur Yvette, (France)

    2007-07-01

    An old mine spoil at a 19. century mining site with considerable residues of uranium (400-800 mg U/kg) was investigated with respect to U concentrations in soil and plants and tolerance to U in the soil microbial community in order to describe the bioavailability of U. Measurements of soil fractions representing water-soluble U, easily exchangeable U, and U bound to humidified organic matter showed that all fractions contained elevated concentrations of U. Plant U concentrations were only 10 times higher at the mine spoil site compared to the reference site (3 mg U/kg vs 0.3 mg U/kg), while the most easily available soil fractions contained 0.18 to 0.86 mg U/kg soil at the mine spoil. An eco-toxicity bioassay using incorporation of [{sup 3}H]thymidine into the indigenous microbial communities of the two soils in the presence of increasing U concentrations showed that microorganisms at the mining site were sensitive to U but also that they had acquired a substantial tolerance toward U (EC50, the effective concentration reducing activity by 50% of UO{sub 2}-citrate was similar to 120 {mu}M as compared to 30 {mu}M in the reference soil). In the assay, more than 40% of the microbial activity was maintained in the presence of 1 mM UO{sub 2}-citrate versus 3% in the reference soil. We conclude that U-enriched mining waste can contain sufficiently elevated concentrations of bio-available U to affect indigenous microorganisms and that bio-available U imposes a selection pressure that favors the development of a highly uranium-tolerant microbial community, while plant uptake of U remains low. (authors)

  6. Bioavailability and microbial adaptation to elevated levels of uranium in an acid, organic topsoil forming on an old mine spoil.

    Science.gov (United States)

    Joner, Erik Jautris; Munier-Lamy, Colette; Gouget, Barbara

    2007-08-01

    An old mine spoil at a 19th-century mining site with considerable residues of uranium (400-800 mg U/kg) was investigated with respect to U concentrations in soil and plants and tolerance to U in the soil microbial community in order to describe the bioavailability of U. Measurements of soil fractions representing water-soluble U, easily exchangeable U, and U bound to humified organic matter showed that all fractions contained elevated concentrations of U. Plant U concentrations were only 10 times higher at the mine spoil site compared to the reference site (3 mg U/kg vs 0.3 mg U/kg), while the most easily available soil fractions contained 0.18 to 0.86 mg U/kg soil at the mine spoil. An ecotoxicity bioassay using incorporation of [3H]thymidine into the indigenous microbial communities of the two soils in the presence of increasing U concentrations showed that microorganisms at the mining site were sensitive to U but also that they had acquired a substantial tolerance toward U (EC50, the effective concentration reducing activity by 50% of UO2-citrate was approximately 120 microM as compared to 30 microM in the reference soil). In the assay, more than 40% of the microbial activity was maintained in the presence of 1 mM UO2-citrate versus 3% in the reference soil. We conclude that U-enriched mining waste can contain sufficiently elevated concentrations of bioavailable U to affect indigenous microorganisms and that bioavailable U imposes a selection pressure that favors the development of a highly uranium-tolerant microbial community, while plant uptake of U remains low.

  7. Comparative growth behaviour and leaf nutrient status of native trees planted on mine spoil with and without nutrient amendment

    Energy Technology Data Exchange (ETDEWEB)

    Singh, A.; Singh, J.S. [Banaras Hindu University, Varanasi (India). Dept. of Botany

    2001-07-01

    The effect of nutrient amendment on growth of nine indigenous tree species planted on coal mine spoil was studied. Greater growth in fertilized plots was accompanied by greater foliar N and P concentrations in all species. The response to fertilization varied among species and was greater in non-leguminous than in leguminous species. Furthermore, leguminous species exhibited higher growth rates compared to non-leguminous species. Acacia catechu, Dalbergia sissoo, Gmelina arborea and Azadirachta indica fitted the elastic similarity model of tree growth; whereas Pongamia pinnata and Phyllanthus emblica followed the constant stress model. Tectona grandis was the only species which fitted the geometric similarity model.

  8. Growth and nutritional status of Brazilian wood species Cedrella fissilis and Anadenanthera peregrina in bauxite spoil in response to arbuscular mycorrhizal inoculation and substrate amendment

    Directory of Open Access Journals (Sweden)

    Tótola Marcos Rogério

    2000-01-01

    Full Text Available The growth of Cedrella fissilis Vell. (Cedro Rosa and of Anadenanthera peregrina Benth (Angico Vermelho in bauxite spoil was studied to evaluate their response to substrate amendment or to inoculation with arbuscular mycorrhizal fungi (AMF. The plants were grown in bauxite spoil, topsoil or spoil amended with either topsoil or compost, and inoculated with the AMF Acaulospora scrobiculata, Gigaspora margarita or Glomus etunicatum. Root colonization was highly dependent on the interaction plant-fungus-substrate. In C. fissilis, root colonization by Gigaspora margarita dropped from 75% in bauxite spoil to only 4% in topsoil. Contrarily, root colonization of A. peregrina by the same fungus increased from 48% in spoil to 60% in topsoil. Root colonization of C. fissilis in topsoil was lower than in the three other substrates. The opposite was observed for A. peregrina. Inoculation of the plants with Acaulospora scrobiculata or Glomus etunicatum was very effective in promoting plant growth. Plants of both C. fissilis and A. peregrina did not respond to amendments of bauxite spoil unless they were mycorrhizal. Also, a preferential partitioning of photosynthates to the shoots of A. peregrina inoculated with G. etunicatum or A. scrobiculata, and of C. fissilis inoculated with any of the three species of AMF was observed. C. fissilis showed a greater response to mycorrhizal inoculation than A. peregrina. The mean mycorrhizal efficiency (ME for dry matter production by C. fissilis was 1,847% for A. scrobiculata, 1,922% for G. etunicatum, and 119% for G. margarita. In A. peregrina, the ME was 249% for A. scrobiculata, 540% for G. etunicatum, and 50% for G. margarita. The effect of mycorrhizal inoculation on plant growth seems to be related in part to an enhanced phosphorus absorption by inoculated plants. Moreover, the efficiency with which the absorbed nutrients were used to produce plant biomass was much greater in plants inoculated with A. scrobiculata or

  9. Inactivation of spoiling microorganisms in apple juice by a combination of essential oils' constituents and physical treatments.

    Science.gov (United States)

    Chueca, Beatriz; Ramírez, Nayeli; Arvizu-Medrano, Sofía M; García-Gonzalo, Diego; Pagán, Rafael

    2016-07-01

    A combination of different hurdles, such as mild heat (54 ℃ for 10 min) or pulsed electric field (25 pulses; 25 kV/cm; 3.35 kJ/cm per pulse) treatments and essential oils constituents (carvacrol, citral, and (+)-limonene), to reduce spoiling bacteria and yeasts in apple juice was evaluated. For this purpose, the heat and pulsed electric field resistances of five strains of Leuconostoc spp. and five Saccharomyces spp. strains were assayed, achieving different inactivation levels for each treatment and strain. For instance, Leuconostoc fallax 74, the most heat-resistant strain, was the second-most sensitive strain to pulsed electric field. The most resistant strains were exposed to combined processes of heat or pulsed electric field and 0.2 µl/ml essential oils constituents. The combination of heat and essential oils constituents proved to be synergistic against both microorganisms in apple juice. The most effective was the combination of mild heat and carvacrol, which caused the inactivation of 99% of L. fallax 74 and 99.99% of Saccharomyces cerevisiae CECT 1172 cells. Therefore, this study shows the great potential of carvacrol, citral, and (+)-limonene in combined treatments with mild heat to achieve a higher degree of inactivation of spoiling microorganisms in apple juice, and thus, to extend its shelf life. © The Author(s) 2015.

  10. Quantitative determination of sediment movement at the landward spoil ground in the Yangtze Estuary with radioactive tracer

    International Nuclear Information System (INIS)

    Li Zhangsu

    1993-01-01

    A radioactive tracer experiment was carried out at the landward spoil ground of the North Passage in the Yangtze Estuary in June of 1991. The scandium-46 was selected as the tracer, the total activity released is 17.95 x 10 10 Bq(4.85 Ci), the amount of the scandium-46 glass is 495 g. The purpose of the experiment is to determine the sediment movement direction, path, velocity and transport rate. The experiment provides the direct evidence for using the landward spoil ground in the future. The experiment results show the sediment movement was governed by the ebb tide current during the period of middle and neap tides when the radioactive tracer was injected both on the flood and ebb tides, and the sediment moved from the injection points to the middle of the North Passage near the navigation buoy No. 269. The direction of the sediment movement is 110 degree, the particle velocity is 758 m/d, and the sediment transport rate per unit width is 47.8 m 3 /md

  11. Radiation-induced enhancement of antifungal activity of chitosan on fruit-spoiling fungi during postharvest storage

    Energy Technology Data Exchange (ETDEWEB)

    Diep, Tran Bang; Lam, Nguyen Duy; Quynh, Tran Minh [Institute for Nuclear Science and Technique-VAEC, Hanoi (Viet Nam); Kume, Tamikazu [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

    2001-03-01

    Experiment conducted four fruit-spoiling fungal strains that were isolated from spoilt fruits (mango and dragon fruit) and were identified as follows: Fusarium dimerum Penzig, Aspergillus nidulans Wint, Aspergillus fumigatus Fresenius and Aspergillus japonicus Saito. Chitosan samples with various deacetylation degree (70-99%) were irradiated at doses ranging from 20 to 200kGy, then were supplemented to liquid medium for growth of fungi. We have found that chitosan possesses not only well known antibacterial activity but also the antifungal one on fruit-spoiling fungi. Method of fungal cultivation using liquid medium showed that it has higher sensitivity compared with the cultivation on agar plate, so we recommend this method should be used for evaluation of antimicrobial activity of chitosan. Our study also indicated that deacetylation degree of chitosan clearly affects its antifungal activity, the higher the deacetylation of chitosan, stronger antifungal activity can be observed. This finding recommends the use of chitosan with higher deacetylation for fruit coating and other pharmacology utilization. Results from the minimal inhibitory concentrations (MIC) on fungal growth showed that radiation treatment increased antifungal activity of chitosan and dose of 60kGy gave highest activity. (author)

  12. Radiation-induced enhancement of antifungal activity of chitosan on fruit-spoiling fungi during postharvest storage

    International Nuclear Information System (INIS)

    Diep, Tran Bang; Lam, Nguyen Duy; Quynh, Tran Minh; Kume, Tamikazu

    2001-01-01

    Experiment conducted four fruit-spoiling fungal strains that were isolated from spoilt fruits (mango and dragon fruit) and were identified as follows: Fusarium dimerum Penzig, Aspergillus nidulans Wint, Aspergillus fumigatus Fresenius and Aspergillus japonicus Saito. Chitosan samples with various deacetylation degree (70-99%) were irradiated at doses ranging from 20 to 200kGy, then were supplemented to liquid medium for growth of fungi. We have found that chitosan possesses not only well known antibacterial activity but also the antifungal one on fruit-spoiling fungi. Method of fungal cultivation using liquid medium showed that it has higher sensitivity compared with the cultivation on agar plate, so we recommend this method should be used for evaluation of antimicrobial activity of chitosan. Our study also indicated that deacetylation degree of chitosan clearly affects its antifungal activity, the higher the deacetylation of chitosan, stronger antifungal activity can be observed. This finding recommends the use of chitosan with higher deacetylation for fruit coating and other pharmacology utilization. Results from the minimal inhibitory concentrations (MIC) on fungal growth showed that radiation treatment increased antifungal activity of chitosan and dose of 60kGy gave highest activity. (author)

  13. Redemption of the "spoiled identity:" the role of HIV-positive individuals in HIV care cascade interventions.

    Science.gov (United States)

    Camlin, Carol S; Charlebois, Edwin D; Geng, Elvin; Semitala, Fred; Wallenta, Jeanna; Getahun, Monica; Kampiire, Leatitia; Bukusi, Elizabeth A; Sang, Norton; Kwarisiima, Dalsone; Clark, Tamara D; Petersen, Maya L; Kamya, Moses R; Havlir, Diane V

    2017-12-01

    The concept of "therapeutic citizenship" has drawn attention to ways in which public testimony, the "story-telling in the public sphere" undertaken by people living with HIV (PLHIV), has shaped the global response to the epidemic. This paper presents qualitative findings from two large studies in eastern Africa that reveal how the advent of population-based HIV testing campaigns and efforts to accelerate antiretroviral "treatment for all" has precipitated a rapidly expanding therapeutic citizenship "project," or social movement. The title of this paper refers to Goffman's original conceptualization of stigma as a social process through which a person's identity is rendered "spoiled." Data were derived from qualitative studies embedded within two clinical trials, Sustainable East African Research in Community Health (SEARCH) (NCT# 01864603) in Kenya and Uganda, and START-ART (NCT# 01810289) in Uganda, which aimed to offer insights into the pathways through which outcomes across the HIV care continuum can be achieved by interventions deployed in the studies, any unanticipated consequences, and factors that influenced implementation. Qualitative in-depth semi-structured interviews were conducted among cohorts of adults in 2014 through 2015; across both studies and time periods, 217 interviews were conducted with 166 individuals. Theoretically informed, team-based analytic approaches were used for the analyses. Narratives from PLHIV, who have not always been conceptualized as actors but rather usually as targets of HIV interventions, revealed strongly emergent themes related to these individuals' use of HIV biomedical resources and discourses to fashion a new, empowered subjecthood. Experiencing the benefits of antiretroviral therapy (ART) emboldens many individuals to transform their "spoiled" identities to attain new, valorized identities as "advocates for ART" in their communities. We propose that the personal revelation of what some refer to as the "gospel of ARVs

  14. Ameliorating effects of industrial sugar residue on the Jales gold mine spoil (NE Portugal) using Holcus lanatus and Phaseolus vulgaris as indicators

    Energy Technology Data Exchange (ETDEWEB)

    Bleeker, P.M.; Teiga, P.M.; Santos, M.H.; Koe, T. de; Verkleij, J.A.C

    2003-09-01

    A residue of the sugar industry can be used in revegetation programs on metal contaminated sites. - Phytostabilisation of bare heavily contaminated substrate, such as abandoned mine sites, is considered a very appropriate technology in order to diminish erosion and dispersion of contaminants into the surroundings. In this short-term pot study, application of industrial sugar residue (ISR), a waste product of the sugar industry, proved to ameliorate spoils conditions for plant performance by elevating pH and immobilising several metals. Although arsenate concentrations were positively correlated to spoil pH and spoil treatment with ISR mobilised As, growth of both Phaseolus vulgaris and Holcus lanatus improved significantly after applications of 3.75 g ISR kg{sup -1} dry spoil. Nutrient uptake from the substrate, with the exception of potassium, was elevated by ISR. As a remediation technique ISR application could be effective although in As-contaminated sites application might be restricted to areas where leaching to (ground) water does not form a risk.

  15. Long-term effects of aided phytostabilisation of trace elements on microbial biomass and activity, enzyme activities, and composition of microbial community in the Jales contaminated mine spoils

    Energy Technology Data Exchange (ETDEWEB)

    Renella, Giancarlo [Department of Soil Science and Plant Nutrition, University of Florence, Piazzale delle Cascine 28, I-50144 Florence (Italy)], E-mail: giancarlo.renella@unifi.it; Landi, Loretta; Ascher, Judith; Ceccherini, Maria Teresa; Pietramellara, Giacomo; Mench, Michel; Nannipieri, Paolo [Department of Soil Science and Plant Nutrition, University of Florence, Piazzale delle Cascine 28, I-50144 Florence (Italy)

    2008-04-15

    We studied the effectiveness of remediation on microbial endpoints, namely microbial biomass and activity, microbial and plant species richness, of an As-contaminated mine spoil, amended with compost (C) alone and in combination with beringite (B) or zerovalent iron grit (Z), to increase organic matter content and reduce trace elements mobility, and to allow Holcus lanatus and Pinus pinaster growth. Untreated spoil showed the lowest microbial biomass and activity and hydrolase activities, and H. lanatus as sole plant species, whereas the presented aided phytostabilisation option, especially CBZ treatment, significantly increased microbial biomass and activity and allowed colonisation by several plant species, comparable to those of an uncontaminated sandy soil. Microbial species richness was only increased in spoils amended with C alone. No clear correlation occurred between trace element mobility and microbial parameters and plant species richness. Our results indicate that the choice of indicators of soil remediation practices is a bottleneck. - Organo-mineral amendment and revegetation of a gold mine spoil increased microbial activity but did not increase microbial species richness.

  16. Long-term effects of aided phytostabilisation of trace elements on microbial biomass and activity, enzyme activities, and composition of microbial community in the Jales contaminated mine spoils

    International Nuclear Information System (INIS)

    Renella, Giancarlo; Landi, Loretta; Ascher, Judith; Ceccherini, Maria Teresa; Pietramellara, Giacomo; Mench, Michel; Nannipieri, Paolo

    2008-01-01

    We studied the effectiveness of remediation on microbial endpoints, namely microbial biomass and activity, microbial and plant species richness, of an As-contaminated mine spoil, amended with compost (C) alone and in combination with beringite (B) or zerovalent iron grit (Z), to increase organic matter content and reduce trace elements mobility, and to allow Holcus lanatus and Pinus pinaster growth. Untreated spoil showed the lowest microbial biomass and activity and hydrolase activities, and H. lanatus as sole plant species, whereas the presented aided phytostabilisation option, especially CBZ treatment, significantly increased microbial biomass and activity and allowed colonisation by several plant species, comparable to those of an uncontaminated sandy soil. Microbial species richness was only increased in spoils amended with C alone. No clear correlation occurred between trace element mobility and microbial parameters and plant species richness. Our results indicate that the choice of indicators of soil remediation practices is a bottleneck. - Organo-mineral amendment and revegetation of a gold mine spoil increased microbial activity but did not increase microbial species richness

  17. [3D FSPGR (fast spoiled gradient echo) magnetic resonance imaging in the diagnosis of focal cortical dysplasia in children].

    Science.gov (United States)

    Alikhanov, A A; Sinitsyn, V E; Perepelova, E M; Mukhin, K Iu; Demushkina, A A; Omarova, M O; Piliia, S V

    2001-01-01

    Small dysplastic lesions of the cerebral cortex are often missed by conventional MRI methods. The identification of subtle structural abnormalities by traditional multiplanar rectilinear slices is often limited by the complex convolutional pattern of the brain. We used a method of FSPGR (fast spoiled gradient-echo) of three-dimensional MRI data that improves the anatomical display of the sulcal structure of the hemispheric convexities. It also reduces the asymmetric sampling of gray-white matter that may lead to false-positive results. We present 5 from 12 patients with dysplastic cortical lesions in whom conventional two-dimensional and three-dimensional MRI with multiplanar reformatting was initially considered normal. Subsequent studies using 3D FSPGR identified various types of focal cortical dysplasia in all. These results indicate that an increase in the detection of subtle focal dysplastic lesions may be accomplished when one improves the anatomical display of the brain sulcal structure by performing 3D FSPGR.

  18. Fat-suppressed three-dimensional fast spoiled gradient-recalled echo imaging: a modified FS 3D SPGR technique for assessment of patellofemoral joint chondromalacia.

    Science.gov (United States)

    Wang, S F; Cheng, H C; Chang, C Y

    1999-01-01

    Fast fat-suppressed (FS) three-dimensional (3D) spoiled gradient-recalled echo (SPGR) imaging of 64 articular cartilage regions in 16 patellofemoral joints was evaluated to assess its feasibility in diagnosing patellofemoral chondromalacia. It demonstrated good correlation with arthroscopic reports and took about half of the examination time that FS 3D SPGR did. This modified, faster technique has the potential to diagnose patellofemoral chondromalacia with shorter examination time than FS 3D SPGR did.

  19. Metal concentrations in earthworms from sewage sludge-amended soils at a strip mine reclamation site

    Energy Technology Data Exchange (ETDEWEB)

    Pietz, R.I.; Peterson, J.R.; Prater, J.E.; Zenz, D.R.

    A 3-yr study of earthworms was initiated in selected mine soil and nonmined fields at a Fulton County, IL land reclamation site. The purpose of this research was to determine the effect of the land application of anaerobically digested sewage sludge, used to reclaim the site, on heavy metal accumulations in earthworms. Two species of earthworms, Lumbricus terrestris and Aporrectodea tuberculata, were identified in the sludge-amended and nonamended, nonmined fields sampled. Only A. tuberculata was found in the sludge-amended and nonamended mine soil fields sampled. Earthworm metal concentrations generally increased with time in all the sampled fields. The decreasing order of metal accumulation by earthworms in all sludge-amended fields sampled was Cu > Cd > Ni > Cr > Pb > Zn. Sewage sludge applications to fields on both land types resulted in significant accumulations of Cd, Cu, and Zn. Land type (mine soil vs. nonmined) significantly affected earthworm Zn concentrations, with levels being higher in all nonmined fields sampled. Earthworm Cd and Cu accumulations in all fields sampled were significantly related to the current amounts of sludge-applied metals, the amount applied since the previous sampling. Concentrations of Ni, Cr, and Pb in earthworms were not significantly related to sewage sludge applications during the 1975 to 1977 sampling period. The higher Cd and Cu concentrations in earthworms from sludge-amended fields may pose a potential hazard to predators.

  20. Aquatic insect deversity and biomass in a stream marginally polluted by acid strip mine drainage

    Energy Technology Data Exchange (ETDEWEB)

    Tomkiewicz, S.M. Jr.; Dunson, W.A.

    1977-01-01

    Upper Three Runs receives a point source of acid mine drainage from a small acid feeder stream and the pH of the main stream falls from above 6 to about 4.5. Over the 1.2 km study section below the introduction of acid drainage, the pH rises to 5.0. This moderate degree of mine acid pollution has severely affected aquatic insect populations. The acid feeder itself (pH near 3.2) was inhabited only by a chironomid, a megalopteran (Sialis), and the caddisfly Ptilostomis. Biomass was very low (140 mg dry weight/m/sup 2/). The drainage of the acid feeder into the stream caused a drop in the Shannon-Weiner diversity index from 3.10 to 1.95, and a drop in biomass from 6.5 g/m/sup 2/ to 2.2 g/m/sup 2/. At the two stations further downstream, the diversity index remained relatively constant and the biomass leveled off at about 1.2 g/m/sup 2/. The number of taxa declined steadily from 30 at the control station to 13 at the lowest site. Populations of Coleoptera, Ephemeroptera and Trichoptera showed little or no recovery as the acid pollution ameliorated slightly. Representatives of the orders Diptera and Plecoptera (especially Nemoura) showed a decided recovery and increase in numbers near pH 5.0. If fish were able to survive in acid mine polluted waters of pH's between 4.5 and 5.0 they should find sufficient insect food for maintenance of a limited population.

  1. Determination of technological parameters in strip mining by time-of-flight and image processing

    Science.gov (United States)

    Elandaloussi, Frank; Mueller, B.; Osten, Wolfgang

    1999-09-01

    The conveying and dumping of earth masses lying over the coal seam in lignite surface mining is done usually by overburden conveyor bridges. The overburden, obtained from connected excavators, is transported over the bridge construction using a conveyor belt system and poured into one front dump and three surface dumps. The shaping of the dump growth is of great importance both to guaranty the stability of the masses dumped to earth stocks as well as the whole construction and to prepare the area for re-cultivation. This article describes three measurement systems: one to determine the impact point of the dumped earth masses, one to determine the shape of the entire mining process and the other a sensor for the loading of the conveyor belt. For the first measurement system, a real-time video system has been designed, set-up and installed that is capable to determine the impact point of all three dumps simultaneously. The second measurement system is a connection of 5 special designed laser distance measuring instruments, that are able to measure the shape of the mining process under unfavorable environmental conditions like dust, high temperature changes, heavy shocks etc. The third sensor is designed for monitoring the transportation of the masses via the conveyor belt system.

  2. Algal and bacterial activities in acidic (pH 3) strip mine lakes

    International Nuclear Information System (INIS)

    Gyure, R.A.; Konopka, A.; Brooks, A.; Doemel, W.

    1987-01-01

    Reservoir 29 and Lake B are extremely acid lakes (epilimnion pHs of 2.7 and 3.2, respectively), because they receive acidic discharges from coal refuse piles. They differ in that the pH of profundal sediments in Reservoir 29 increased from 2.7 to 3.8 during the period of thermal stratification, whereas permanently anoxic sediments in Lake B had a pH of 6.2. The pH rise in Reservoir 29 sediments was correlated with a temporal increase in H 2 S concentration in the anaerobic hypolimnion from 0 to >1 mM. The chlorophyll a levels in the epilimnion of Reservoir 29 were low, and the rate of primary production was typical of an oligotrophic system. However, there was a dense 10-cm layer of algal biomass at the bottom of the metalimnion. Production by this layer was low owing to light limitation and possibly H 2 S toxicity. The specific photosynthetic rates of epilimnetic algae were low, which suggests that nutrient availability is more important than pH in limiting production. The highest photosynthetic rates were obtained in water samples incubated at pH 2.7 to 4. Heterotrophic bacterial activity (measured by [ 14 C]glucose metabolism) was greatest at the sediment/water interface. Bacterial production (assayed by thymidine incorporation) was as high in Reservoir 29 as in a nonacid mesotrophic Indiana lake

  3. Recolonization of wildlife on a coal strip-mine in northwestern New Mexico. [USA - New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Ireland, T.T.; Wolters, G.L.; Schemnitz, S.D. (US Fish and Wildlife Service, Grand Junction, CO (United States))

    1994-03-01

    Recolonization by small mammals, reptiles, amphibians, and arthropods was studied in 1988 and 1989 on The Pittsburg and Midway Coal Mine in northwestern New Mexico. Sites reclaimed in 1979, 1982, and 1986 were compared with unmined sites for differences in animal composition and abundance. Wildlife components were compared with vegetative composition and physical ground features to determine if these influenced wildlife recolonization. The greater species richness of small mammals and the greater abundance of reptiles on the control treatment suggests that reclaimed sites are not providing suitable rock or woody cover for some species. Positive correlations of rock cover and wood cover with small-mammal species richness and the total reptile and amphibian captures indicate that placing rocks and wood cover on reclaimed sites may be beneficial to several small mammal, reptile, and amphibian species.

  4. Heavy metal concentrations in redeveloping soil of mine spoil under plantations of certain native woody species in dry tropical environment, India

    Energy Technology Data Exchange (ETDEWEB)

    Singh, A.N.; Zeng, D.H.; Chen, F.S. [Chinese Academy of Science, Shenyang (China). Inst. of Applied Ecology

    2005-07-01

    Total concentration of heavy metals (Cd, Cr, Cu, Fe, Pb, Ni, Mn and Zn) was estimated in the redeveloping soil of mine spoil under 5-yr old plantations of four woody species namely: Albizia lebbeck, Albizia procera, Tectona grandis and Dendrocalamus strictus. The data recorded in the present study were compared with other unplanted coal mine spoil colliery, which was around to the study site and adjoining area of dry tropical forest. Among all the heavy metals, the maximum concentration was found for Fe and minimum for Cd. However, among all four species, total concentrations of these heavy metals were recorded maximally in the plantation plots of T. grandis except for Fe, while minimally in A. lebbeck except for Zn, whereas, the maximum concentration of Fe and Zn was in the plantation plots of D. strictus and A. procera. Statistical analysis revealed significant differences due to species for all the heavy metals except Cu. Among four species, A. lebbeck, A. procera and D. strictus showed more efficient for reducing heavy metal concentrations whereas T. grandis was not more effective to reduce heavy metal concentrations in redeveloping soil of mine spoil.

  5. Heavy metal concentrations in redeveloping soil of mine spoil under plantations of certain native woody species in dry tropical environment, India.

    Science.gov (United States)

    Singh, Anand N; Zeng, De-hui; Chen, Fu-sheng

    2005-01-01

    Total concentration of heavy metals (Cd, Cr, Cu, Fe, Pb, Ni, Mn and Zn) was estimated in the redeveloping soil of mine spoil under 5-yr old plantations of four woody species namely: Albizia lebbeck, Albizia procera, Tectona grandis and Dendrocalamus strictus. The data recorded in the present study were compared with other unplanted coal mine spoil colliery, which was around to the study site and adjoining area of dry tropical forest. Among all the heavy metals, the maximum concentration was found for Fe and minimum for Cd. However, among all four species, total concentrations of these heavy metals were recorded maximally in the plantation plots of T. grandis except for Fe, while minimally in A. lebbeck except for Zn, whereas, the maximum concentration of Fe and Zn was in the plantation plots of D. strictus and A. procera. Statistical analysis revealed significant differences due to species for all the heavy metals except Cu. Among four species, A. lebbeck, A. procera and D. strictus showed more efficient for reducing heavy metal concentrations whereas T. grandis was not more effective to reduce heavy metal concentrations in redeveloping soil of mine spoil.

  6. Relationship between the trochlear groove angle and patellar cartilage morphology defined by 3D spoiled gradient-echo imaging

    Energy Technology Data Exchange (ETDEWEB)

    Harada, Yuko; Tokuda, Osamu; Matsunaga, Naofumi [Yamaguchi University Graduate School of Medicine, Department of Radiology, Yamaguchi (Japan); Fukuda, Kouji [Shunan Memorial Hospital, Division of Radiological Technology, Yamaguchi (Japan); Shiraishi, Gen; Motomura, Tetsuhisa [Shunan Memorial Hospital, Department of Orthopedics Surgery, Yamaguchi (Japan); Kimura, Motoichi [Customer Application Gr., GE Healthcare MR Sales and Marketing Department, Osaka (Japan)

    2012-05-15

    To examine whether the femoral trochlear groove angle (TGA) is a determinant of the patellar cartilage volume and patellar cartilage damage. Patellar cartilage was evaluated by MR imaging in 66 patients (22 males and 44 females) with knee pain. Fat-suppressed 3D spoiled gradient-echo images were used to calculate the cartilage volume and to grade the cartilage damage. The proximal and distal TGAs were measured from axial PD-weighted FSE MR images with fat suppression. For every increase in the TGA at the distal femur, the patellar cartilage volume was significantly increased by 6.07 x 10{sup -3} cm{sup 3} (95% CI: 1.27 x 10{sup -3}, 10.9 x 10{sup -3}) after adjustment for age, gender, and patellar bone volume (P < 0.05). The MR grade of medial patellar cartilage damage progressed as the distal TGA became narrower, although there was no significant correlation between the distal TGA and the MR grading of patellar cartilage damage. A more flattened distal TGA was associated with increased patellar cartilage volume. However, there was no association between TGA and patellar cartilage defects. (orig.)

  7. Aluminum-Tolerant Pisolithus Ectomycorrhizas Confer Increased Growth, Mineral Nutrition, and Metal Tolerance to Eucalyptus in Acidic Mine Spoil

    Directory of Open Access Journals (Sweden)

    Louise Egerton-Warburton

    2015-01-01

    Full Text Available Ectomycorrhizal fungi (ECM may increase the tolerance of their host plants to Al toxicity by immobilizing Al in fungal tissues and/or improving plant mineral nutrition. Although these benefits have been demonstrated in in vitro (pure culture or short-term nutrient solution (hydroponic experiments, fewer studies have examined these benefits in the field. This study examined the growth, mineral nutrition, and Al levels in two Eucalyptus species inoculated with three Pisolithus ecotypes that varied in Al tolerance (in vitro and grown in mine spoil in the greenhouse and field. All three ecotypes of Pisolithus improved Eucalyptus growth and increased host plant tolerance to Al in comparison to noninoculated plants. However, large variations in plant growth and mineral nutrition were detected among the Pisolithus-inoculated plants; these differences were largely explained by the functional properties of the Pisolithus inoculum. Seedlings inoculated with the most Al-tolerant Pisolithus inoculum showed significantly higher levels of N, P, Ca, Mg, and K and lower levels of Al than seedlings inoculated with Al-sensitive ecotypes of Pisolithus. These findings indicate an agreement between the fungal tolerance to Al in vitro and performance in symbiosis, indicating that both ECM-mediated mineral nutrient acquisition and Al accumulation are important in increasing the host plant Al tolerance.

  8. Plant Communities Rather than Soil Properties Structure Arbuscular Mycorrhizal Fungal Communities along Primary Succession on a Mine Spoil

    Science.gov (United States)

    Krüger, Claudia; Kohout, Petr; Janoušková, Martina; Püschel, David; Frouz, Jan; Rydlová, Jana

    2017-01-01

    Arbuscular mycorrhizal fungal (AMF) community assembly during primary succession has so far received little attention. It remains therefore unclear, which of the factors, driving AMF community composition, are important during ecosystem development. We addressed this question on a large spoil heap, which provides a mosaic of sites in different successional stages under different managements. We selected 24 sites of c. 12, 20, 30, or 50 years in age, including sites with spontaneously developing vegetation and sites reclaimed by alder plantations. On each site, we sampled twice a year roots of the perennial rhizomatous grass Calamagrostis epigejos (Poaceae) to determine AMF root colonization and diversity (using 454-sequencing), determined the soil chemical properties and composition of plant communities. AMF taxa richness was unaffected by site age, but AMF composition variation increased along the chronosequences. AMF communities were unaffected by soil chemistry, but related to the composition of neighboring plant communities of the sampled C. epigejos plants. In contrast, the plant communities of the sites were more distinctively structured than the AMF communities along the four successional stages. We conclude that AMF and plant community successions respond to different factors. AMF communities seem to be influenced by biotic rather than by abiotic factors and to diverge with successional age. PMID:28473828

  9. Richness, diversity and evenness of vegetation upon rehabilitation of gypsum mine spoiled lands in the Indian arid zone

    Science.gov (United States)

    Kumar, S.; Sharma, K.D.; Sharma, U.K.; Gough, L.P.

    1998-01-01

    Richness, diversity and evenness of vegetation, after rehabilitation of gypsum mine spoils at Barmer were investigated in plots protected and planted one year and four years ago. There were four water harvesting treatments, viz., half-moon terraces, micro-catchments with 5% slope, ridge and furrow and control, wherein, indigenous and exotic trees and shrubs were planted at 5 ?? 5 m spacing. Sampling of the planted and natural vegetation, using quadrats and transacts, revealed much less species richness in unplanted control as compared to all treatments and in all the years. The species richness that increased initially (within one year) gradually declined over time (during four year), though the extent varied in different treatments. The water harvesting treatment showing maximum initial increase in richness also showed maximum decline over time, though decline was more in annual species. Two perennial species increased in richness with time. This was further proved from the trends in diversity and evenness indices. It was concluded that natural successional process was accelerated by rehabilitation providing stability to the habitat.

  10. Acid mine drainage abatement resulting from pressure grouting of buried bituminous mine spoils

    International Nuclear Information System (INIS)

    Scheetz, B.; Silsbee, M.; Schueck, J.

    1998-01-01

    A 37 acre surface coal mine located in Clinton County, PA, USA, was mined and reclaimed between 1974 and 1977. Buried pyrite-rich pit floor cleanings and tipple refuse were found to be producing severe acid mine drainage. The pyritic material is located in discrete piles or pods in the backfill. The pods and the resulting contaminant plumes were initially defined using geophysical techniques and confirmed by drilling. The approach taken was to use a cementitious grout, composed of fluidized bed combustion ash and water, which would be placed in a manner which would prevent water and oxygen from contacting the pyritic materials. Statistically significant water quality improvements have been noted as a result of the grouting. After four years of post-grouting monitoring, reductions in concentrations of most of the mine drainage parameters range from 40 to 90%. 12 refs., 1 fig., 4 tabs

  11. Suitability of dredged material for reclamation of surface-mined land. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, W.; Van Luik, A.

    1979-12-01

    Eroding ridges of acidic coal-mine spoil in La Salle County, Illinois, were leveled to form a gently-sloped raised plateau. Four test plots were constructed: a control plot and three treatment plots that received a 0.9-m-thick cover of dredged material obtained from the Metropolitan Sanitary District of Greater Chicago. Two treatment plots received lime applications and all plots were seeded with a mixture of grasses. Pressure-vacuum soil water samplers were installed, in duplicate, at two levels in the control plot and at three levels in each treatment plot. The three levels in the treatment plots coincided with dredged material, the dredged-material mine-spoil interface, and the underlying mine spoil. Surface water, soil water, and groundwater were monitored for 29 water-quality parameters for one year. Rainfall, air temperature, runoff, and water-level elevation data were collected also. Detailed analysis of the data indicates that the dredged material used in this study does not adversely affect water quality; it supports abundant plant growth, lessens groundwater contamination, and controls acid runoff. The dredged material is judged to be a suitable material for use in reclamation of surface-mined land.

  12. Phytoremediation of heavy metal contaminated soil potential by woody plants on Tonglushan ancient copper spoil heap in China.

    Science.gov (United States)

    Kang, Wei; Bao, Jianguo; Zheng, Jin; Xu, Fen; Wang, Liuming

    2018-01-02

    Fast-growing metal-accumulating woody plants are considered potential candidates for phytoremediation of metals. Tonglushan mining, one of the biggest Cu production bases in China, presents an important source of the pollution of environment. The sample was collected at Tonglushan ancient copper spoil heap. The aims were to measure the content of heavy metal in the soil and woody plants and to elucidate the phytoremediation potential of the plants. The result showed that soil Cu, Cd and Pb were the main contamination, the mean contents of which were 3166.73 mg/kg, 3.66 mg/kg and 137.06 mg/kg respectively, which belonged to severe contamination. Fourteen species from 14 genera of 13 families were collected and investigated; except for Ligutrum lucidum, the other 13 woody plants species were newly recorded in this area. In addition, to assess the ability of metal accumulation of these trees, we proposed accumulation index. Data suggested that Platanus × acerilolia, Broussonetia papyrifera, Ligutrum lucidum, Viburnum awabuki, Firmiana simplex, Robina pseudoacacia, Melia azedarach and Osmanthus fragrans exhibited high accumulated capacity and strong tolerance to heavy metals. Therefore, Platanus × acerilolia and Broussonetia papyrifera can be planted in Pb contaminated areas; Viburnum awabuki, Firmiana simplex, Robina pseudoacacia and Melia azedarach are the suitable trees for Cd contaminated areas; Viburnum awabuki, Melia azedarach, Ligutrum lucidum, Firmiana simplex, Osmanthus fragrans and Robina pseudoacacia are appropriate to Cu, Pb and Cd multi-metal contaminated areas.

  13. Biosurfactant-producing bacterium, Pseudomonas aeruginosa MA01 isolated from spoiled apples: physicochemical and structural characteristics of isolated biosurfactant.

    Science.gov (United States)

    Abbasi, Habib; Hamedi, Mir Manochehr; Lotfabad, Tayebe Bagheri; Zahiri, Hossein Shahbani; Sharafi, Hakimeh; Masoomi, Fatemeh; Moosavi-Movahedi, Ali Akbar; Ortiz, Antonio; Amanlou, Massoud; Noghabi, Kambiz Akbari

    2012-02-01

    An extensive investigation was conducted to isolate indigenous bacterial strains with outstanding performance for biosurfactant production from different types of spoiled fruits, food-related products and food processing industries. An isolate was selected from 800 by the highest biosurfactant yield in soybean oil medium and it was identified by 16S rRNA and the two most relevant hypervariable regions of this gene; V3 and V6 as Pseudomonas aeruginosa MA01. The isolate was able to produce 12 g/l of a glycolipid-type biosurfactant and generally less efficient to emulsify vegetable oils compared to hydrocarbons and could emulsify corn and coconut oils more than 50%. However, emulsification index (E(24)) of different hydrocarbons including hexane, toluene, xylene, brake oil, kerosene and hexadecane was between 55.8% and 100%. The surface tension of pure water decreased gradually with increasing biosurfactant concentration to 32.5 mNm(-1) with critical micelle concentration (CMC) value of 10.1mg/l. Among all carbon substrates examined, vegetable oils were the most effective on biosurfactant production. Two glycolipid fractions were purified from the biosurfactant crude extracts, and FTIR and ES-MS were used to determine the structure of these compounds. The analysis indicated the presence of three major monorhamnolipid species: R(1)C(10)C(10), R(1)C(10)C(12:1), and R(1)C(10)C(12); as well as another three major dirhamnolipid species: R(2)C(10)C(10), R(2)C(10)C(12:1), and R(2)C(10)C(12). The strain sweep experiment for measuring the linear viscoelastic of biosurfactant showed that typical behavior characteristics of a weak viscoelastic gel, with storage modulus greater than loss modulus at all frequencies examined, both showing some frequency dependence. Copyright © 2011 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  14. Absolute Quantification of Human Liver Phosphorus-Containing Metabolites In Vivo Using an Inhomogeneous Spoiling Magnetic Field Gradient

    Science.gov (United States)

    Bashir, Adil; Gropler, Robert; Ackerman, Joseph

    2015-01-01

    Purpose Absolute concentrations of high-energy phosphorus (31P) metabolites in liver provide more important insight into physiologic status of liver disease compared to resonance integral ratios. A simple method for measuring absolute concentrations of 31P metabolites in human liver is described. The approach uses surface spoiling inhomogeneous magnetic field gradient to select signal from liver tissue. The technique avoids issues caused by respiratory motion, chemical shift dispersion associated with linear magnetic field gradients, and increased tissue heat deposition due to radiofrequency absorption, especially at high field strength. Methods A method to localize signal from liver was demonstrated using superficial and highly non-uniform magnetic field gradients, which eliminate signal(s) from surface tissue(s) located between the liver and RF coil. A double standard method was implemented to determine absolute 31P metabolite concentrations in vivo. 8 healthy individuals were examined in a 3 T MR scanner. Results Concentrations of metabolites measured in eight healthy individuals are: γ-adenosine triphosphate (ATP) = 2.44 ± 0.21 (mean ± sd) mmol/l of wet tissue volume, α-ATP = 3.2 ± 0.63 mmol/l, β-ATP = 2.98 ± 0.45 mmol/l, inorganic phosphates (Pi) = 1.87 ± 0.25 mmol/l, phosphodiesters (PDE) = 10.62 ± 2.20 mmol/l and phosphomonoesters (PME) = 2.12 ± 0.51 mmol/l. All are in good agreement with literature values. Conclusions The technique offers robust and fast means to localize signal from liver tissue, allows absolute metabolite concentration determination, and avoids problems associated with constant field gradient (linear field variation) localization methods. PMID:26633549

  15. Influence of surface flattening on biodiversity of terrestrial arthropods during early stages of brown coal spoil heap restoration.

    Science.gov (United States)

    Moradi, Jabbar; Potocký, Pavel; Kočárek, Petr; Bartuška, Martin; Tajovský, Karel; Tichánek, Filip; Frouz, Jan; Tropek, Robert

    2018-08-15

    Heterogeneity of environmental conditions is the crucial factor supporting biodiversity in various habitats, including post-mining sites. The effects of micro-topographic heterogeneity on biodiversity and conservation potential of arthropod communities in post-industrial habitats had not been studied before now. At one of the largest European brown coal spoil heaps, we sampled eight groups of terrestrial arthropods with different life strategies (moths, spiders, ground beetles, ants, orthopteroids, centipedes, millipedes, and woodlice), in successionally young plots (5-18 y), with a heterogeneous wavy surface after heaping, and compared the communities with plots flattened by dozing. A combination of the standardized quantitative sampling, using two different methods, and a paired design of the plot selection enabled a robust analysis. Altogether, we recorded 380 species of the focal arthropods, 15 of them nationally threatened. We revealed the importance of the micro-topographic heterogeneity for the formation of the biodiversity of arthropods in their secondary refuges. The communities with higher biodiversity and conservation value were detected in the plots with heterogeneous surfaces; exceptions were ground beetles and millipedes. The surface flattening, often the first step of technical reclamation projects, thus suppress biodiversity of most terrestrial arthropods during the restoration of post-mining sites. Since the communities of both surface types differed, the proportional presence on both surfaces could be more efficient in supporting the local biodiversity. We suggest reducing the surface dozing for the cases with other concerns only, to achieve a proportional representation of both surface types. Such a combination of different restoration approaches would, thus, efficiently support high biodiversity of groups with various needs. Copyright © 2018 Elsevier Ltd. All rights reserved.

  16. Mycorrhizal status of plants in two successional stages on spoil heaps from fireloam mining in Lower Silesia (SW Poland

    Directory of Open Access Journals (Sweden)

    Dorota Kasowska

    2014-01-01

    Full Text Available The mycorrhizal status of two plant communities representing an initial stage (1-2 year-old and a 8-9-year-old stage of succession on spoil heaps from fireloam mining in Lower Silesia, Poland, was determined. In the initial stage, the mycorrhizal structures were not observed in 39% of the investigated species; they were members of the Polygonaceae, Chenopodiaceae and Poaceae families. The relative cover of non-mycorrhizal plants exceeded 50% and the major role was played by the Polygonum aviculare population, which predominated the whole community. Mycorrhizal species (arbuscular mycorrhizae contributed to 61 % of the composition of the initial phyto-coenosis. The most numerous taxa were those with 20-40% of the root length colonized, with a small number of arbuscules (0.2-3.1% of the root length containig arbuscules and no vesicles. In the advanced stage of succession, mycorrhizal plants definitely dominated and the major role was played by the Tussilago farfara population. Compared with the initial stage, the later one also harboured more plants with mycorrhizas occupied >40% of the root length, as well as containing numerous arbuscules (>20% of the root length and vesicles. The non-mycorrhizal species, i.e., Equisetum arvense and Poa compressa, represented 11 % o': the community composition and their relative cover amounted to 3%. Despite the relatively frequent occurrence of the arbuscular mycorrhizae in the initial stage of succession, the qualitative properties of the colonization indicated a low effectiveness of symbiosis. This could be caused by the lack of adaptation of the fungal symbiont to the edaphic conditions which were changed after disturbance.

  17. Effect of modern technology in improving spoil bank design and reducing environmental pollution

    Energy Technology Data Exchange (ETDEWEB)

    Knezevic, D [Rudarski Institut, Belgrade (Yugoslavia). Zavod za Pripremu Mineralnih Sirovina

    1988-01-01

    States that Yugoslav thermal power plants produce 10 Mt ash annually with only 10% being utilized as a secondary raw material, and that the environmental pollution resulting from inappropriate disposal methods is no longer acceptable. Points out that hydraulic ash transport at thermal power plants uses 20,000 m{sup 3} water per hour for 200 MW plants, and that the water dissolves heavy metal ions. Very high levels of Pb, As, and Cu ions together with sulphates were found in water released from the ash disposal sites of the Nikola Tesla and Kostolac thermal power plants where the level of suspended particles was found in spring 1985 to have risen to 4,500 mg/l against a permitted level of 30 mg/l. Recommends the use of sealing foil under ash disposal areas to prevent the contamination of ground water. The spraying of dry ash and slag waste is also recommended to prevent air pollution by dust. Slag is stated to be the more serious contaminant; typical ash to slag ratios vary from 95:5 to 80:20. With large disposal areas such as at the Kostolac or Nikola Tesla A and B power plants where 250-400 ha could be involved, a program of land reclamation and recultivation is suggested. Further recommends that outmined coalfields be used as sites for ash and slag disposal. 7 refs.

  18. Arsenic and selenium mobilisation from organic matter treated mine spoil with and without inorganic fertilisation

    International Nuclear Information System (INIS)

    Moreno-Jiménez, Eduardo; Clemente, Rafael; Mestrot, Adrien; Meharg, Andrew A.

    2013-01-01

    Organic matter amendments are applied to contaminated soil to provide a better habitat for re-vegetation and remediation, and olive mill waste compost (OMWC) has been described as a promising material for this aim. We report here the results of an incubation experiment carried out in flooded conditions to study its influence in As and metal solubility in a trace elements contaminated soil. NPK fertilisation and especially organic amendment application resulted in increased As, Se and Cu concentrations in pore water. Independent of the amendment, dimethylarsenic acid (DMA) was the most abundant As species in solution. The application of OMWC increased pore water dissolved organic-carbon (DOC) concentrations, which may explain the observed mobilisation of As, Cu and Se; phosphate added in NPK could also be in part responsible of the mobilisation caused in As. Therefore, the application of soil amendments in mine soils may be particularly problematic in flooded systems. Highlights: ► Organic and inorganic amendments were added to a mine soil in flooding conditions. ► Olive mill waste compost (OMWC) provoked As, Se and Cu solubilisation. ► Dimethylarsenic acid (DMA) was the predominant As species in pore water. ► Selenium volatilisation from soils was intense. - The addition of organic amendment and/or inorganic fertiliser to a trace element contaminated soil in flooded conditions led to As, Cu and Se solubilisation.

  19. Soil organic carbon and nitrogen accumulation on coal mine spoils reclaimed with maritime pine (Pinus pinaster Aiton) in Agacli-Istanbul.

    Science.gov (United States)

    Sever, Hakan; Makineci, Ender

    2009-08-01

    Mining operations on open coal mines in Agacli-Istanbul have resulted in the destruction of vast amounts of land. To rehabilitate these degraded lands, plantations on this area began in 1988. Twelve tree species were planted, however, the most planted tree species was maritime pine (Pinus pinaster Aiton). This study performed on 14 sample plots randomly selected in maritime pine plantations on coal mine soil/spoils in 2005. Soil samples were taken from eight different soil layers (0-1, 1-3, 3-5, 5-10, 10-20, 20-30, 30-40 and 40-50 cm) into the soil profile. On soil samples; fine soil fraction (<2 mm), soil acidity (pH), organic carbon (C(org)) and total nitrogen (N(t)) contents were investigated, and results were compared statistically among soil layers. As a result, 17 years after plantations, total forest floor accumulation determined as 17,973.20 kg ha(-1). Total nitrogen and organic matter amounts of forest floor were 113.90 and 14,640.92 kg ha(-1) respectively. Among soil layers, the highest levels of organic carbon (1.77%) and total nitrogen (0.096%) and the lowest pH value (pH 5.38) were found in 0-1 cm soil layer, and the variation differs significantly among soil layers. Both organic carbon and total nitrogen content decreased, pH values increased from 0-1 to 5-10 cm layer. In conclusion, according to results obtained maritime pine plantations on coal mine spoils; slow accumulation and decomposition of forest floor undergo simultaneously. Depending on these changes organic carbon and total nitrogen contents increased in upper layer of soil/spoil.

  20. Reestablishment of woody plants on mine spoils and management of mine water impoundments: an overview of Forest Service research on the northern High Plain

    Energy Technology Data Exchange (ETDEWEB)

    Bjugstad, A J

    1977-01-01

    The function of the research unit at Rapid city, S. Dakota, is to provide guidelines for the reestablisment of shrubs and trees on land characteristic of the High Plains, and for the mitigation of possible detrimental effects of surface mining on ground water and surface water. One possible problem posed by surface mining concerns the formation of land drainage patterns that could result in post-mining formations of large salt playas. Surface mining could affect shallow ground water aquifers up to /sup 1///sub 4/ mile from the mine site. Research is being conducted on the reclamation of mine spoils and on the rehabilitation and management of impounded mine water.

  1. Characteristics of N-Acylhomoserine Lactones Produced by Hafnia alvei H4 Isolated from Spoiled Instant Sea Cucumber

    Directory of Open Access Journals (Sweden)

    Hong-Man Hou

    2017-04-01

    Full Text Available This study aimed to identify N-acylhomoserine lactone (AHL produced by Hafnia alvei H4, which was isolated from spoiled instant sea cucumber, and to investigate the effect of AHLs on biofilm formation. Two biosensor strains, Chromobacterium violaceum CV026 and Agrobacterium tumefaciens KYC55, were used to detect the quorum sensing (QS activity of H. alvei H4 and to confirm the existence of AHL-mediated QS system. Thin layer chromatography (TLC and high resolution triple quadrupole liquid chromatography/mass spectrometry (LC/MS analysis of the AHLs extracted from the culture supernatant of H. alvei H4 revealed the existence of at least three AHLs: N-hexanoyl-l-homoserine lactone (C6-HSL, N-(3-oxo-octanoyl-l-homoserine lactone (3-oxo-C8-HSL, and N-butyryl-l-homoserine lactone (C4-HSL. This is the first report of the production of C4-HSL by H. alvei. In order to determine the relationship between the production of AHL by H. alvei H4 and bacterial growth, the β-galactosidase assay was employed to monitor AHL activity during a 48-h growth phase. AHLs production reached a maximum level of 134.6 Miller unites at late log phase (after 18 h and then decreased to a stable level of about 100 Miller unites. AHL production and bacterial growth displayed a similar trend, suggesting that growth of H. alvei H4 might be regulated by QS. The effect of AHLs on biofilm formation of H. alvei H4 was investigated by adding exogenous AHLs (C4-HSL, C6-HSL and 3-oxo-C8-HSL to H. alvei H4 culture. Biofilm formation was significantly promoted (p < 0.05 by 5 and 10 µM C6-HSL, inhibited (p < 0.05 by C4-HSL (5 and 10 µM and 5 µM 3-oxo-C8-HSL, suggesting that QS may have a regulatory role in the biofilm formation of H. alvei H4.

  2. Intentional introduction of Biscutella laevigata L. on the post-flotation lead-zinc ore spoil heap in Piekary Śląskie (Upper Silesia, Southern Poland

    Directory of Open Access Journals (Sweden)

    Rostański Adam

    2014-09-01

    Full Text Available The paper presents an account of the successful intentional introduction of the mountain species Biscutella laevigata to a lowland locality, as a result of field experiment - biological management at the toxic “Dołki” washery spoil heap (Lead and Zinc Ore Main and Factory ZGH “Orzeł Biały” (Upper Silesia – Southern Poland. The aim of the presented study was to test the effectiveness possibilities of using the blend of seeds including a metallophyte – Biscutella laevigata seeds. The introduction of Biscutella laevigata was a part of an experiment which began in 2009-2010 with plots on the "Dolki" washery spoil heap. The tested seeds of Biscutella laevigata were examined for germination, growth and development in sites highly polluted with heavy metals. Biscutella laevigata appeared on two experimental plots. After 4 years there were numerous individuals of Biscutella – dozens of plants in various stages of development and phenology. Development of a Biscutella population from year to year (2 plants in 2010 – 58 plants in 2014 is larger and tends to increase. Biscutella individuals are spreading outside the designated test plots. The obtained results indicate that on sites highly polluted with heavy metals it is possible to perform a successful introduction of Biscutella laevgata population (increase from 2 individuals in 2010 to 58 individuals in 2014 from seeds. These results are also promising in terms of application as a new reclamation method.

  3. Possibilities for production of medicinal aromatic plants on the spoil bank of the Pljevlja coal mine. Mogucnost gajenja ljekovitog i aromaticnog bilja na jalovistu rudnika uglja - Pljevlja

    Energy Technology Data Exchange (ETDEWEB)

    Memic, M.; Bajovic, L. (Rudnik Uglja Pljevlja (Yugoslavia))

    1990-01-01

    Presents results obtained from experimental recultivation of the Potrlica surface coal mine spoil bank (810 m elevation, continental climate) during 1986-1990. Two experimental fields - Potrlica-I (600 m[sup 2]) and Potrlica-II (300 m[sup 2]) - were prepared by spreading a 10-20 cm thick layer of low-quality soil over the marly waste of the spoil bank. Soil composition was: 2.10% and 74% Ca, 4.5% and 0.70% humus, l3.5% and 5.5% P[sub 2]O[sub 5] and 23.0% and 6.0% K[sub 2]O in Potrlica-I and II respectively. Soil pH values were 7.2 and 7.60; 500 kg/ha NPK (15:15:15) were spread. Seventeen species of aromatic and medicinal plants were grown. After four years the plants were classified into 3 groups (thriving, satisfactory and non-thriving). It was found that the following plants can yield satisfactory crops and profits: valeriana officinalis, hyssopus officinalis, artemis dracunculus, cynaris scolimus, foenculum vulgare and malva silvestris. Unsatisfactory results were obtained with melisa officinalis, coriandrum sativum, pimpinela anisum and angelica archangelica. Experiments will be continued.

  4. Restoration Practices Used on Post Mining Sites and Industrial Deposits in the Czech Republic with an Example of Natural Restoration of Granodiorite Quarries and Spoil Heaps

    Directory of Open Access Journals (Sweden)

    Chuman Tomáš

    2015-11-01

    Full Text Available Mining of minerals that have significant impact on landscape and landscape functions affects 1% of the land surface worldwide. In the Czech Republic the extent of mining sites is estimated to be more than 800 km2 and according to the state legislation the land affected by mining should be reclaimed. There are several approaches to land restoration, which are shortly reviewed in this article, from pure technical approach to one adopting natural processes. The review shows increasing appeal of scientist and conservationist to use natural processes e.g. natural or directed succession as an alternative method of post-mining sites or industrial deposits restoration due to growing evidence of conservational value of such sites in human dominated landscapes. The natural processes used for land restoration are often argued to be slow therefore the rate of spontaneous vegetation succession was assessed in stone quarries and on spoil heaps using a sequence of panchromatic aerial images. The results showed that natural processes act fast and vegetation can reach 100% cover within 10-15 years in granodiorite quarries and on spoil heaps.

  5. Homogeneity spoil spectroscopy

    International Nuclear Information System (INIS)

    Hennig, J.; Boesch, C.; Martin, E.; Grutter, R.

    1987-01-01

    One of the problems of in vivo MR spectroscopy of P-31 is spectra localization. Surface coil spectroscopy, which is the method of choice for clinical applications, suffers from the high-intensity signal from subcutaneous muscle tissue, which masks the spectrum of interest from deeper structures. In order to suppress this signal while maintaining the simplicity of surface coil spectroscopy, the authors introduced a small sheet of ferromagnetically dotted plastic between the surface coil and the body. This sheet destroys locally the field homogeneity and therefore all signal from structures around the coil. The very high reproducibility of the simple experimental procedure allows long-term studies important for monitoring tumor therapy

  6. Investigations of water pollution effects of mining spoil heaps depending on the period of existence. Final report. Part project 2; Untersuchungen gewaesserrelevanter Einfluesse von Bergbauhalden in Abhaengigkeit von der Standzeit. Abschlussbericht. Teilprojekt 2

    Energy Technology Data Exchange (ETDEWEB)

    Puchelt, H.; Stueben, D.; Berner, Z.; Kappes, B.

    1996-12-01

    Apart form the main elements, the Wiesloch Ag-Pb-Zn mineralisation contains a series of higly toxic trace elements. The main ore minerals of galena, zinc blende and Menikow pyrites also contain Tl, Cd, As and Sb up to the precent range. The main and trace element contents of ores, flotation residues and slags were examined in detail. Their weathering properties were estimated, depending on the time of existence, from new secondary mineral formations. An element displacement from the spoil heaps reaching several decimetres in the ceiling was shown. Strong contamination can be proved by washing out and dispersion of As and Tl in agriculturally used areas and can be found in plants. Using elution experiments, the metal release of hevy metals and arsenic from ores, flotation wastes and slags was examined for the quantitative estimation of the material transfer. Also, the excellent suitability of synthetic Fe-Mn hydroxides for the decontamination of water containing arsenic and heavy metals was shown. (orig.) [Deutsch] Die Wieslocher Ag-Pb-Zn-Vererzung enthaelt neben den Hauptelementen eine Reihe von hochtoxischen Spurenelementen. Die Haupterzminerale Bleiglanz, Zinkblende und Melnikowitpyrit enthalten zusaetzlich Tl, Cd, As sowie Sb bis in den Prozentbereich. Im Detail wurde der Haupt- und Spurenelementgehalt von Erzen, Flotationsrueckstaenden und Schlacken untersucht. Ihre Verwitterungseigenschaften wurden in Abhaengigkeit der Standzeit anhand von sekundaeren Mineralneubildungen abgeschaetzt. Eine mehrere dm-weit reichende Elementverlagerung aus Halden in das Liegende (Loessdecke) konnte nachgewiesen werden. Starke Kontaminationen sind durch Auswaschung und Dispersion von As und Tl in landwirtschaftlich genutzen Flaechen nachzuweisen und in Pflanzen wiederfindbar. Zur quantitativen Abschaetzung des Stofftransfers wurde anhand von Elutionsversuchen die Metallfreisetzung von Schwermetallen und Arsen aus Erz, Flotationsabgaengen und Schlacken untersucht. Ausserdem konnte

  7. Optimization of three-dimensional triple IR fast spoiled gradient recalled acquisition in the steady state (FSPGR) to decrease vascular artifact at 3.0 Tesla

    International Nuclear Information System (INIS)

    Fujiwara, Yasuhiro; Fukuya, Yuko; Yamaguchi, Isao; Matsuda, Tsuyoshi; Ishimori, Yoshiyuki; Yamada, Kazuhiro; Kimura, Hirohiko; Miyati, Tosiaki

    2006-01-01

    The purpose of this study was to decrease vascular artifacts caused by the in-flow effect in three-dimensional inversion recovery prepared fast spoiled gradient recalled acquisition in the steady state (3D IR FSPGR) at 3.0 Tesla. We developed 3D triple IR (3IR) FSPGR and examined the signal characteristics of the new sequence. We have optimized scan parameters based on simulation, phantom, and in-vivo studies. As a result, optimized parameters (1st TI=600 ms, 3rd TI=500 ms) successfully have produced the vessel signal at more than 40% reduction, while gray-white matter contrast was preserved. Moreover, the reduced artifact was also confirmed by visual inspection of the in-vivo images for which this condition was used. Thus, 3D 3IR FSPGR was a useful sequence for the acquisition of T1-weighted images at 3.0 Tesla. (author)

  8. Counter-measures to reduce the effects of spoil tips on the quality of ground water-standard-setting boundary conditions and implementation; Gegenmassnahmen zur Verminderung der Auswirkungen von Abraumkippen auf die Grundwasserbeschaffenheit. Normative Rahmenbedingungen und Umsetzung

    Energy Technology Data Exchange (ETDEWEB)

    Cremer, Nils [Erfverband, Bergheim (Germany). Abt. Grundwasser; Bolle, Christian [Ministerium fuer Wirtschaft, Energie, Bauen, Wohnen und Verkehr des Landes Nordrhein-Westfalen, Duesseldorf (Germany)

    2010-10-15

    The lignite mining industry in North Rhine-Westphalia gives rise to large spoil tips because of the mining methods. In the Rhenish lignite districts spoil quantities of over 30 bn m{sup 3} will accumulate in tips covering a total area of 300 km{sup 2} by the end of open-cast mining in the 2040s. It is important to counteract by suitable measures the effects of these waste tips, which are characterised essentially by pyrite oxidation, on the future quality of ground water after its renewed rise. This contribution describes the counter-measures already used for some time to reduce the effects on the ground water quality both from standard-setting, chemical and technical points of view. Furthermore the effectiveness of the measures described and thus the contribution to ground water protection and also to safeguard of the water supply can be specified. (orig.)

  9. Managing dredged material in the coastal zone of the Baltic Sea.

    Science.gov (United States)

    Staniszewska, Marta; Boniecka, Helena

    2017-01-01

    This article deals with the legal and practical recommendations for the management of dredged material in the riparian countries of the Baltic Sea. The recommendations are contained in three conventions: LC, 2000. London Convention (1972), Convention on the Protection of the Marine Environment of the Baltic Sea area (Helsinki Convention) (1992), the OSPAR Convention (1972). Different approaches to evaluating the contamination level of dredge spoils, used by the Baltic Sea riparian countries, have been characterized. The differences in those approaches manifest themselves by various concentration limits for contaminants, which form a basis for the classification of dredged material as either contaminated or non-contaminated, and thus determine how the spoils will be processed further. Based on the collected information about the concentration limits for contaminants of surface sediments in the coastal ports, it was pointed out that it is necessary to conduct routine monitoring of heavy metals, polycyclic aromatic hydrocarbons, polychlorinated biphenyls, tributyltin, and petroleum hydrocarbons in dredged sediments in all the Baltic Sea states. On the other hand, the monitoring of polychlorinated dibenzo-p-dioxins/furans, organochlorine, and organophosphoric pesticides is only needed in locations that are suspected of historical or being the local contamination sources. Due to significant economic limitations of chemical determinations, it is important to consider a simple screening test of sediment that would say whether sediment may be "contaminated" and qualifies for more detailed and costly chemical research. It may be typical basic physical-chemical analysis of sediments or ecotoxicological classification of sediments.Despite environmentally friendly tendencies, the practical application of dredged material within the Baltic Sea area is very limited. Dredged material is most frequently stored at the specifically designated sites. From among the practical uses of

  10. The Identification of Novel Diagnostic Marker Genes for the Detection of Beer Spoiling Pediococcus damnosus Strains Using the BlAst Diagnostic Gene findEr.

    Directory of Open Access Journals (Sweden)

    Jürgen Behr

    Full Text Available As the number of bacterial genomes increases dramatically, the demand for easy to use tools with transparent functionality and comprehensible output for applied comparative genomics grows as well. We present BlAst Diagnostic Gene findEr (BADGE, a tool for the rapid prediction of diagnostic marker genes (DMGs for the differentiation of bacterial groups (e.g. pathogenic / nonpathogenic. DMG identification settings can be modified easily and installing and running BADGE does not require specific bioinformatics skills. During the BADGE run the user is informed step by step about the DMG finding process, thus making it easy to evaluate the impact of chosen settings and options. On the basis of an example with relevance for beer brewing, being one of the oldest biotechnological processes known, we show a straightforward procedure, from phenotyping, genome sequencing, assembly and annotation, up to a discriminant marker gene PCR assay, making comparative genomics a means to an end. The value and the functionality of BADGE were thoroughly examined, resulting in the successful identification and validation of an outstanding novel DMG (fabZ for the discrimination of harmless and harmful contaminations of Pediococcus damnosus, which can be applied for spoilage risk determination in breweries. Concomitantly, we present and compare five complete P. damnosus genomes sequenced in this study, finding that the ability to produce the unwanted, spoilage associated off-flavor diacetyl is a plasmid encoded trait in this important beer spoiling species.

  11. Cultivation of high-biomass crops on coal mine spoil banks: Can microbial inoculation compensate for high doses of organic matter?

    Energy Technology Data Exchange (ETDEWEB)

    Gryndler, M.; Sudova, R.; Puschel, D.; Rydlova, J.; Janouskova, M.; Vosatka, M. [Academy of Science Czech Republic, Pruhonice (Czech Republic)

    2008-09-15

    Two greenhouse experiments were focused on the application of arbuscular mycorrhizal fungi (AMF) and plant growth promoting rhizobacteria (PGPR) in planting of high-biomass crops on reclaimed spoil banks. In the first experiment, we tested the effects of different organic amendments on growth of alfalfa and on the introduced microorganisms. While growth of plants was supported in substrate with compost amendment, mycorrhizal colonization was suppressed. Lignocellulose papermill waste had no negative effects on AMF, but did not positively affect growth of plants. The mixture of these two amendments was found to be optimal in both respects, plant growth and mycorrhizal development. Decreasing doses of this mixture amendment were used in the second experiment, where the effects of microbial inoculation (assumed to compensate for reduced doses of organic matter) on growth of two high-biomass crops, hemp and reed canarygrass, were studied. Plant growth response to microbial inoculation was either positive or negative, depending on the dose of the applied amendment and plant species.

  12. Effect of lime, N, P, and K amendments to surface-mined coal spoils on yield and chemical composition of common Bermuda grass

    Energy Technology Data Exchange (ETDEWEB)

    Ebelhar, M W; Barnhisel, R I; Akin, G W; Powell, J L

    1982-12-01

    Common Bermuda grass (Cynodon dactylon, L. Pers.) was used as an alternative to cool-season grasses such as tall fescue (Festuca arundinacea Schreb.) on acid sandstone surface-mine spoils in western Kentucky. Lime, N, P, and K fertilizer amendments were evaluated as to their effects in promoting Bermuda grass growth and development. The applied lime was effective in raising the pH from 3.4 to 4.6, 5.7, and 6.3 for the 18, 36 and 72 metric ton/ha treatments, respectively, over a 17-month period. Nitrogen was found to affect Bermuda grass production significantly and severe deficiency symptoms were observed where N was not applied. Dry matter yields increased significantly with each additional increment of N applied. Although the application of P and K increased the concentration of these ions in the plant tissues, the main influence of P and K was to increase the plants' resistance to winter killing; little effect on total dry matter production was observed. 19 references.

  13. The Identification of Novel Diagnostic Marker Genes for the Detection of Beer Spoiling Pediococcus damnosus Strains Using the BlAst Diagnostic Gene findEr.

    Science.gov (United States)

    Behr, Jürgen; Geissler, Andreas J; Schmid, Jonas; Zehe, Anja; Vogel, Rudi F

    2016-01-01

    As the number of bacterial genomes increases dramatically, the demand for easy to use tools with transparent functionality and comprehensible output for applied comparative genomics grows as well. We present BlAst Diagnostic Gene findEr (BADGE), a tool for the rapid prediction of diagnostic marker genes (DMGs) for the differentiation of bacterial groups (e.g. pathogenic / nonpathogenic). DMG identification settings can be modified easily and installing and running BADGE does not require specific bioinformatics skills. During the BADGE run the user is informed step by step about the DMG finding process, thus making it easy to evaluate the impact of chosen settings and options. On the basis of an example with relevance for beer brewing, being one of the oldest biotechnological processes known, we show a straightforward procedure, from phenotyping, genome sequencing, assembly and annotation, up to a discriminant marker gene PCR assay, making comparative genomics a means to an end. The value and the functionality of BADGE were thoroughly examined, resulting in the successful identification and validation of an outstanding novel DMG (fabZ) for the discrimination of harmless and harmful contaminations of Pediococcus damnosus, which can be applied for spoilage risk determination in breweries. Concomitantly, we present and compare five complete P. damnosus genomes sequenced in this study, finding that the ability to produce the unwanted, spoilage associated off-flavor diacetyl is a plasmid encoded trait in this important beer spoiling species.

  14. Biofertilizers for the revegetation of coal overburden dumps top materials

    Energy Technology Data Exchange (ETDEWEB)

    Nikhil, K. [Central Mining Research Institute, Dhanbad (India). Environmental Management Group

    2001-07-01

    Adding and improving nutrient status of overburden dump top material through biofertilizer for supporting vegetation and for sustainable spoil development, a pot experiment was conducted. In this, two bio-fertilizers namely bactin and phosphin in three doses were applied on overburden dump top material kept in pots growing two grass species. The growths were compared with control on dump and soil both. Results shows that overburden dump amended with bio-fertilizer at lowest dose have significant increase in growth over the control of dump material and soil in vetiver grass but failed to shows the same result in lemon grass. This may be due to different growth behaviour of the grasses. 14 refs., 2 tabs.

  15. Reclamation technology development for western Arkansas coal refuse waste materials

    International Nuclear Information System (INIS)

    King, J.R.; Veith, D.L.

    1994-01-01

    Coal mining has been an important industry in the Arkansas River Valley Major Land Resource Area (MLRA) of western Arkansas for more than 100 yr., most of it with little regard for environmental concerns. Almost 3,640 ha. of land affected by surface coal mines cover the seven-county area, with less than 1,200 ha. currently in various stages of operation or reclamation. Since only the active mining sites must now be reclaimed by law, the remaining 2,440 ha. of abandoned land remains at the mercy of natural forces. Little topsoil exists on these sites and the coal wastes are generally acidic with a pH in the 4.0-5.5 range. Revegetation attempts under these conditions generally require continued maintenance and retreatment until an acceptable cover is achieved. If and when an acceptable vegetative cover is established, the cost frequently approaches $7,400/ha. ($3,000/acre). In an effort to resolve these issues and provide some direction for stabilizing coal waste lands, the US Department of Agriculture through its Soil Conservation Service Plant Materials Center at Boonville, Arkansas, received a Congressional Pass through administered by the US Bureau of Mines, to support a 5-yr. revegetation study on the coal mine spoils of western Arkansas. This paper reports the results through the spring of 1994 on that portion of the study dealing with the establishment of blackberries as a cash crop on coal mine spoils

  16. Comparison of fast spin echo, fast multiplanner spoiled gradient recalled and conventional T1 and T2 weighted imaging for experimentally induced hepatic tumors in rats

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Myeong Jin; Lee, Jong Tae; Suh, Jin Suk; Choi, Pil Sik; Lee, Yeon Hee; Yoo, Hyung Sik; Kim, Ki Whang [Yonsei University College of Medicine, Seoul (Korea, Republic of)

    1994-10-15

    To compare the ability of tumor detection and the lesion conspicuity between T1- and T2-weighted fast scanning sequence and T1- and T2-weighted conventional spin echo techniques in MR imaging of hepatic tumors. Hepatic tumors were induced on 13 male Sprague-Dawley rats by feeding 3'-methyl-dimethylethyl aminoazobenzene mixed with Miller's III formula for 12 weeks. MR images were obtained with 1.5 T magnet with dual TMJ coil(Sigma, GE Medical systems, Milwaukee, USA). Animals were anesthetized with 150 mg/kg of ketamine hydrochloride. T2 weighted fast spin echo(FSE), conventional spin echo(CSE) T2- and T1WI, fast multiplanner spoiled gradient recalled(FMPSPGR) imaging were obtained. Number of detected tumors and contrast-to-noise ratio of the tumors were compared for each sequence. Overall 110 tumors were developed. 75% of the tumors were detected on FSE. 65% on FMPSPGR, 41% on conventional T2WI, and 41% on T1WI images. For tumors more than 5 mm in diameter, sensitivity was 88% on FMPSPGR, 65% on conventional T2WI, and 81% on T1WI images respectively. CNR of the tumor was 28.94 {+-} 21.6 on FSE, 13.57 {+-} 8.64 on FMPSPGR, 12.62 {+-} 10.65 on CSE T2WI, and 9.47 {+-} 8.05 on CSE T1WI images, which was significantly high on FSE(p<0.05). Fast spin echo T2WI shows highest sensitivity and tumor-to-liver contrast. FMPSPGR imaging is also favorably comparable with conventional T1WI. Therefore, these two pulse sequences can be useful in clinical condition for hepatic MR imaging.

  17. Thawed cod fillets spoil less rapidly than unfrozen fillets when stored under modified atmosphere at 2 degrees C.

    Science.gov (United States)

    Guldager, H S; Bøknaes, N; Osterberg, C; Nielsen, J; Dalgaard, P

    1998-09-01

    The effect of two months of frozen storage at -20 degrees C on the spoilage characteristics and shelf life of thawed and modified atmosphere packed (MAP) cod fillets stored at 2 degrees C was studied. Thawed MAP cod fillets were compared with fresh cod fillets stored in CO2-containing modified atmospheres with and without added oxygen. The shelf life of 11 to 12 days in the fresh MAP cod was extended to more than 20 days in the thawed MAP cod at 2 degrees C. This shelf life extension was most likely due to the inactivation of the spoilage bacterium Photobacterium phosphoreum during frozen storage as reflected both in chemical analyses and sensory evaluation. In contrast to fresh MAP cod fillets no significant production of trimethylamine occurred and almost no amine odor and taste were detected during 20 days of chill storage of thawed MAP cod fillets. The use of frozen fillets as raw material not only provides a more stable product in MAP but also allows much greater flexibility for production and distribution. However, a slightly increased concentration of dimethylamine, a larger drip loss, and detection of weak frozen storage flavor were observed in the thawed MAP cod fillets.

  18. Chemical and isotopic tracing of underground water in relation with leaching of mine spoils, Nord-Pas-de-Calais Coal Basin (France); Tracage chimique et isotopique des eaux souterraines en relation avec les eaux de lixiviation de terrils, bassin minier du Nord-Pas-de-Calais (France)

    Energy Technology Data Exchange (ETDEWEB)

    Denimal, S.; Tribovillard, N.; Meilliez, F. [Lille-1 Univ., Lab. de Sedimentologie et Geodynamique, UMR 8577, 59 - Villeneuve-d' Ascq (France); Barbecot, F.; Dever, L. [Paris-11 Univ., Lab. d' Hydrologie et de Geochimie Isotopique, UMR 8616, 91 - Orsay (France)

    2001-07-01

    Coal mining activity in the Nord-Pas-de-Calais region (Northern France) has generated many mine spoils. The oxidation of the pyrite content of such coal shales and their leaching can be a source of sulfate pollution for the underlying chalk aquifer, i.e. the main drinking water resource of the region. Two sites of study have been retained: one in the free water table zone and the other in the confined water table zone. Samples from both mine spoils have been analyzed with respect to their carbon and sulfur content and a superficial leaching of these elements has been evidenced. Water has been sampled in piezometers and boreholes close to the mine spoils and also along natural flux lines. The use of sulfur isotopes as markers of the different sulfate sources has confirmed the spoils source but has permitted to identify another source in the second site which is the Tertiary gypsum-bearing Ostricourt sands. This study has shown also that in the confined water table zone, part of the exported sulfates is reduced. This bacterial reduction of sulfates is due to a joint leaching of both carbon and sulfur in the mine spoils. A self-purification phenomenon occurs when the chalk aquifer is confined beneath the Cenozoic cover. (J.S.)

  19. radiochemical studies on the binding of humic materials with toxic elements and compounds

    International Nuclear Information System (INIS)

    Afifi, D.M.I.

    2001-01-01

    industrial nations produce several billion tons of waste every year . this figure will increase as both population and industrial growth increase. there are many kinds of waste, including refinery waste, which consists of hydrocarbons, heavy metals, metal catalysts and caustic solution; dredge spoils, some of which are highly polluted and cntains substances potentially hazardous to human health or the marine ecosystem; chemical waste such as insecticides, pesticides, other complex chemicals and heavy metals; radioactive waste and agricultural waste, anmd most of them are extremely hazardous and harmful to the marine ecosystem and its inhabitants.the aim of this thesis is to study the binding of humic materials with toxic elements and compounds

  20. An analysis of the uncertainty and bias in DCE-MRI measurements using the spoiled gradient-recalled echo pulse sequence

    International Nuclear Information System (INIS)

    Subashi, Ergys; Choudhury, Kingshuk R.; Johnson, G. Allan

    2014-01-01

    Purpose: The pharmacokinetic parameters derived from dynamic contrast-enhanced (DCE) MRI have been used in more than 100 phase I trials and investigator led studies. A comparison of the absolute values of these quantities requires an estimation of their respective probability distribution function (PDF). The statistical variation of the DCE-MRI measurement is analyzed by considering the fundamental sources of error in the MR signal intensity acquired with the spoiled gradient-echo (SPGR) pulse sequence. Methods: The variance in the SPGR signal intensity arises from quadrature detection and excitation flip angle inconsistency. The noise power was measured in 11 phantoms of contrast agent concentration in the range [0–1] mM (in steps of 0.1 mM) and in onein vivo acquisition of a tumor-bearing mouse. The distribution of the flip angle was determined in a uniform 10 mM CuSO 4 phantom using the spin echo double angle method. The PDF of a wide range of T1 values measured with the varying flip angle (VFA) technique was estimated through numerical simulations of the SPGR equation. The resultant uncertainty in contrast agent concentration was incorporated in the most common model of tracer exchange kinetics and the PDF of the derived pharmacokinetic parameters was studied numerically. Results: The VFA method is an unbiased technique for measuringT1 only in the absence of bias in excitation flip angle. The time-dependent concentration of the contrast agent measured in vivo is within the theoretically predicted uncertainty. The uncertainty in measuring K trans with SPGR pulse sequences is of the same order, but always higher than, the uncertainty in measuring the pre-injection longitudinal relaxation time (T1 0 ). The lowest achievable bias/uncertainty in estimating this parameter is approximately 20%–70% higher than the bias/uncertainty in the measurement of the pre-injection T1 map. The fractional volume parameters derived from the extended Tofts model were found to be

  1. Acidic minespoil reclamation with alkaline biosolids

    International Nuclear Information System (INIS)

    Drill, C.; Lindsay, B.J.; Logan, T.L.

    1998-01-01

    The effectiveness of an alkaline stabilized biosolids product, N-Viro Soil (NVS), was studied at a wild animal preserve in Cumberland, OH. The preserve occupies land that was strip mined for high-sulfur coal. While most of the land has been conventionally reclaimed, several highly acidic hot spots remain. Two of these hot spots were studied through concurrent field, greenhouse, and laboratory projects. In April 1995, NVS was applied at rates ranging from 0--960 mt/ha (wet wt.) to plots at the two sites. The plots were seeded using a standard reclamation mix and soil samples were analyzed for chemical characteristics before and after application and also in 1996 and 1997. Soil pH increased from 3.5 to about 11 in the amended plots and soil EC values increased from 21.0 mmho/cm to a maximum of 6.0 mmho/cm in the amended plots immediately after application. Soil Cu and Zn concentrations also increased in the NVS amended plots, but this did not affect plant germination or growth. By the summer of 1996, soil pH values had decreased to 7.3--8.7 and EC values decreased to 0.34--1.36 mmho/cm to the amended plots. Soil samples were collected in September 1995 for physical analyses. N-Viro Soil improved the moisture retention and water conductivity properties of the spoil. The plots were monitored for growth during the summer of 1995 and plant biomass and soil samples were taken in 1996 and 1997 for trace element and nutrient analysis. NVS did not significantly increase trace element concentrations in the biomass. The addition of NVS to acid mine spoil improves the chemical and physical properties of the spoil material thus aiding vegetative establishment and growth. NVS improves the chemical nature of the spoil by increasing pH and providing micro and macronutrients and improves the physical properties of the spoil with the addition of organic matter

  2. Childhood, race and spoiling kids

    OpenAIRE

    Oliveira, Fabiana de; Abramowicz, Anete

    2010-01-01

    Atualmente, o campo das discussões que se referem às relações étnico-raciais vem se ampliando em um espaço político-educacional considerável e que contribui para desmontar um forte campo discursivo que se hegemonizou como verdade e que afirmava a existência de uma democracia racial. Este artigo é o resultado de uma pesquisa desenvolvida numa instituição de educação infantil durante um semestre letivo, com visitas diárias. A coleta de dados foi realizada utilizando os seguintes recursos: obser...

  3. Qualidade do substrato minerado de uma área de empréstimo revegetada no distriro federal Quality of a revegeted mine spoil in the federal disrict of Brazil

    Directory of Open Access Journals (Sweden)

    Rodrigo Studart Corrêa

    2010-08-01

    Full Text Available O uso de resíduos orgânicos tem-se mostrado eficaz para a revegetação de áreas mineradas. Entretanto, dados acerca da qualidade de substratos tratados com resíduos orgânicos são escassos. Dessa forma, este trabalho visou avaliar a qualidade edáfica de um substrato minerado no Distrito Federal que recebeu 250 Mg ha-1 de lodo de esgoto e uma cobertura herbácea estabelecida a partir de sementes. Os atributos edáficos utilizados na avaliação foram densidade de solo, porosidade total, água disponível, resistência mecânica à penetração, ΔpH, CTC, saturação por bases, P disponível, matéria orgânica, abundância e diversidade da macrofauna de solo. Os resultados mostraram que a incorporação do lodo de esgoto e o desenvolvimento de um estrato herbáceo resultaram em melhoria das qualidades química e biológica do substrato exposto pela mineração, mas não alteraram a qualidade física dele. A dose de lodo de esgoto utilizada elevou os valores dos atributos químicos para além dos medidos em solos sob Cerrado nativo. Caso o objetivo da recuperação seja a restauração do ecossistema local, técnicas que melhorem a qualidade física do substrato e não excedam os níveis naturais de fertilidade devem ser desenvolvidas.The use of organic residues has been shown to be effective for the revegetation of mined areas. However, data on the quality of mine spoils treated with organic residues are rather scarce. This study aimed to evaluate the spoil quality of a mined area in the Brazilian Federal District treated with 250 Mg ha-1 of domestic sewage sludge and covered with herbs grown from seeds. The soil attributes used for the evaluation were bulk density, total porosity, available water capacity, soil resistance to penetration, ΔpH, CEC, base saturation, available phosphorus, organic matter content, abundance and diversity of soil macro-fauna. Results show that plowing sewage sludge into the spoil and the establishment of a

  4. Quantifying the effect of water activity and storage temperature on single spore lag times of three moulds isolated from spoiled bakery products.

    Science.gov (United States)

    Dagnas, Stéphane; Gougouli, Maria; Onno, Bernard; Koutsoumanis, Konstantinos P; Membré, Jeanne-Marie

    2017-01-02

    The inhibitory effect of water activity (a w ) and storage temperature on single spore lag times of Aspergillus niger, Eurotium repens (Aspergillus pseudoglaucus) and Penicillium corylophilum strains isolated from spoiled bakery products, was quantified. A full factorial design was set up for each strain. Data were collected at levels of a w varying from 0.80 to 0.98 and temperature from 15 to 35°C. Experiments were performed on malt agar, at pH5.5. When growth was observed, ca 20 individual growth kinetics per condition were recorded up to 35days. Radius of the colony vs time was then fitted with the Buchanan primary model. For each experimental condition, a lag time variability was observed, it was characterized by its mean, standard deviation (sd) and 5 th percentile, after a Normal distribution fit. As the environmental conditions became stressful (e.g. storage temperature and a w lower), mean and sd of single spore lag time distribution increased, indicating longer lag times and higher variability. The relationship between mean and sd followed a monotonous but not linear pattern, identical whatever the species. Next, secondary models were deployed to estimate the cardinal values (minimal, optimal and maximal temperatures, minimal water activity where no growth is observed anymore) for the three species. That enabled to confirm the observation made based on raw data analysis: concerning the temperature effect, A. niger behaviour was significantly different from E. repens and P. corylophilum: T opt of 37.4°C (standard deviation 1.4°C) instead of 27.1°C (1.4°C) and 25.2°C (1.2°C), respectively. Concerning the a w effect, from the three mould species, E. repens was the species able to grow at the lowest a w (aw min estimated to 0.74 (0.02)). Finally, results obtained with single spores were compared to findings from a previous study carried out at the population level (Dagnas et al., 2014). For short lag times (≤5days), there was no difference between lag

  5. Dictionary materials engineering, materials testing

    International Nuclear Information System (INIS)

    1994-01-01

    This dictionary contains about 9,500 entries in each part of the following fields: 1) Materials using and selection; 2) Mechanical engineering materials -Metallic materials - Non-metallic inorganic materials - Plastics - Composites -Materials damage and protection; 3) Electrical and electronics materials -Conductor materials - Semiconductors - magnetic materials - Dielectric materials - non-conducting materials; 4) Materials testing - Mechanical methods - Analytical methods - Structure investigation - Complex methods - Measurement of physical properties - Non-destructive testing. (orig.) [de

  6. Energy and human welfare: a critical analysis. Volume I. The social costs of power production

    International Nuclear Information System (INIS)

    Commoner, B.; Boksenbaum, H.; Corr, M.

    1975-01-01

    Statements are presented of the Board of Directors of the American Association for the Advancement of Science and the Committee on Environmental Alterations. Following the Preface by Barry Commoner, eighteen papers are presented: Thermal Pollution and Its Control by Christopher T. Hill; Biologic Effects of Air Pollution by Robert Frank; Acid Rain by Gene E. Likens, F. Herbert Bormann, and Noye M. Johnson; Environmental Consequences of Extracting Coal by Michael Fortune; Reclamation of Strip Mine Spoil Banks in Wyoming by Morton May, Robert Lang, Leandro Lujan, Peter Jacoby, and Wesley Thompson; Oil Spills by Max Blumer, Howard L. Sanders, J. Fred Grassle, and George R. Hampson; Nuclear Power: Its Promise and Its Problems by Milton Shaw; Radioactivity from Fossil-Fuel and Nuclear Power Plants by J. E. Martin, E. D. Harward, D. T. Oakley, J. M. Smith, and P. H. Bedrosion; A Reevaluation of Reactor Safety by Daniel F. Ford; Management of Radioactive Wastes from the Use of Nuclear Fuel by George Berg; Storage of High Level Radioactive Wastes by William W. Hambleton; Plutonium and Public Health by Donald P. Geesaman; Radiation: The Invisible Casualties by John W. Gofman and Arthur R. Tamplin; The Need for National and International Systems to Provide Physical Security for Fissionable Materials by Theodore B. Taylor; and Nuclear Electric Power by Sheldon Novick

  7. Material Science

    Energy Technology Data Exchange (ETDEWEB)

    Won, Dong Yeon; Kim, Heung

    1987-08-15

    This book introduces material science, which includes key of a high-tech industry, new materials of dream like new metal material and semiconductor, classification of materials, microstructure of materials and characteristic. It mentions magic new materials such as shape memory alloy, fine ceramics, engineering fine ceramics, electronic ceramics, engineering plastic, glass, silicone conductor, optical fiber mixed materials and integrated circuit, challenge for new material and development of new materials.

  8. Material Science

    International Nuclear Information System (INIS)

    Won, Dong Yeon; Kim, Heung

    1987-08-01

    This book introduces material science, which includes key of a high-tech industry, new materials of dream like new metal material and semiconductor, classification of materials, microstructure of materials and characteristic. It mentions magic new materials such as shape memory alloy, fine ceramics, engineering fine ceramics, electronic ceramics, engineering plastic, glass, silicone conductor, optical fiber mixed materials and integrated circuit, challenge for new material and development of new materials.

  9. Materials and material testing

    International Nuclear Information System (INIS)

    Joergens, H.

    1978-01-01

    A review based on 105 literature quotations is given on the latest state of development in the steel sector and in the field of non-ferrous metals and plastics. The works quoted also include, preparation, working, welding including simulation methods, improvement of weldability, material mechanics (explanation of defects mechanisms by means of fracture mechanics), defect causes (corrosion, erosion, hydrogen influence), mechanical-technological and non-destructive material testing. Examples from the field of reactor building are also given within there topics. (IHOE) [de

  10. Optical materials

    International Nuclear Information System (INIS)

    Poker, D.B.; Ortiz, C.

    1989-01-01

    This book reports on: Diamond films, Synthesis of optical materials, Structure related optical properties, Radiation effects in optical materials, Characterization of optical materials, Deposition of optical thin films, and Optical fibers and waveguides

  11. Strategic Materials

    National Research Council Canada - National Science Library

    Buhler, Carl; Burke, Adrian; Davis, Kirk; Gerhard, Michelle; Heil, Valerie; Hulse, Richard; Kwong, Ralph; Mahoney, Michael; Moran, Scott; Peek, Michael

    2006-01-01

    Some materials possess greater value than others. Materials that provide essential support for the nation's economic viability or enable critical military capabilities warrant special attention in security studies...

  12. Contrast-enhanced three-dimensional fast-spoiled gradient magnetic resonance angiography of the renal arteries for potential living renal transplant donors: a comparative study with digital subtraction angiography

    International Nuclear Information System (INIS)

    Al-Saeed, O.; Sheikh, M.; Al-Khawari, H.; Ismail, M.; Al-Moosawi, M.

    2005-01-01

    Preoperative assessment of the arterial anatomy of prospective renal donors is essential. Various non-invasive techniques are used for such evaluation. We conducted this study using contrast-enhanced 3-D fast-spoiled gradient (CE 3-D FSPGR) magnetic resonance angiography (MRA) on a 1.0 Tesla magnet, for preoperative definition of the renal arteries. Forty-five preoperative living renal donors underwent CE 3-D FSPGR MRA of the renal vessels and the results were compared with conventional digital subtraction angiography (DSA). The renal vascular anatomy, both normal and with variations, was satisfactorily defined in all 45 cases with CE 3-D FSPGR MRA. Fifteen cases showed an accessory or aberrant arterial supply. A small aneurysm was shown in one case. All cases compared well with conventional DSA. Our study revealed that CE 3-D FSPGR MRA on a lower field strength magnet is accurate in defining the renal vascular anatomy and its variations. Copyright (2005) Blackwell Science Pty Ltd

  13. Reduction of vascular artifact on T1-weighted images of the brain by using three-dimensional double IR fast spoiled gradient echo recalled acquisition in the steady state (FSPGR) at 3.0 Tesla

    International Nuclear Information System (INIS)

    Fujiwara, Yasuhiro; Yamaguchi, Isao; Ookoshi, Yusuke; Ootani, Yuriko; Matsuda, Tsuyoshi; Ishimori, Yoshiyuki; Hayashi, Hiroyuki; Miyati, Tosiaki; Kimura, Hirohiko

    2007-01-01

    The purpose of this study was to decrease vascular artifacts caused by the in-flow effect in three-dimensional inversion recovery prepared fast spoiled gradient recalled acquisition in the steady state (3D IR FSPGR) at 3.0 Tesla. We developed 3D double IR FSPGR and investigated the signal characteristics of the new sequence. The 3D double IR FSPGR sequence uses two inversion pulses, the first for obtaining tissue contrast and the second for nulling vascular signal, which is applied at the time of the first IR period at the neck region. We have optimized scan parameters based on both phantom and in-vivo study. As a result, optimized parameters (1st TI=700 ms, 2nd TI=400 ms) successfully have produced much less vessel signal at reduction than conventional 3D IR FSPGR over a wide imaging range, while preserving the signal-to-noise ratio (SNR) and gray/white matter contrast. Moreover, the decreased artifact was also confirmed by visual inspection of the images obtained in vivo using those parameters. Thus, 3D double IR FSPGR was a useful sequence for the acquisition of T1-weighted images at 3.0 Tesla. (author)

  14. Materials Chemistry

    CERN Document Server

    Fahlman, Bradley D

    2011-01-01

    The 2nd edition of Materials Chemistry builds on the strengths that were recognized by a 2008 Textbook Excellence Award from the Text and Academic Authors Association (TAA). Materials Chemistry addresses inorganic-, organic-, and nano-based materials from a structure vs. property treatment, providing a suitable breadth and depth coverage of the rapidly evolving materials field. The 2nd edition continues to offer innovative coverage and practical perspective throughout. After briefly defining materials chemistry and its history, seven chapters discuss solid-state chemistry, metals, semiconducting materials, organic "soft" materials, nanomaterials, and materials characterization. All chapters have been thoroughly updated and expanded with, for example, new sections on ‘soft lithographic’ patterning, ‘click chemistry’ polymerization, nanotoxicity, graphene, as well as many biomaterials applications. The polymer and ‘soft’ materials chapter represents the largest expansion for the 2nd edition. Each ch...

  15. Environmental control technology survey of selected US strip mining sites. Volume 2A: Ohio: water quality impacts and overburden chemistry of Ohio study site

    Energy Technology Data Exchange (ETDEWEB)

    Bogner, J E; Henricks, J D; Olsen, R D; Schubert, J P; Sobek, A A; Wilkey, M L; Johnson, D O

    1979-05-01

    An intensive study of water, overburden, and coal chemistry was conducted at a large surface mine in Ohio from May 1976 through July 1977. Sampling sites were chosen to include the final mine effluent at the outflow of a large settling pond and chemically-treated drainage from a coal storage pile. Samples were collected semimonthly and analyzed for total dissolved solids, total suspended solids, alkalinity, acidity, sulfate, chloride, and 16 metals. Field measurements included pH, flow rate, dissolved oxygen, and specific conductance. The final effluent, where sampled, generally complied with Office of Surface Mining reclamation standards for pH, iron, and total suspended solids. Comparison of the final effluent with water quality of an unnamed tributary above the mine suggested that elevated values for specific conductance, total dissolved solids, sulfate, calcium, magnesium, manganese, and zinc were attributable to the mine operation. In general, there were observable seasonal variations in flow rates that correlated positively to suspended solids concentrations and negatively to concentrations of dissolved constituents in the final effluent. Drainage from the coal storage pile contained elevated levels of acidity and dissolved metals which were not reduced significantly by the soda ash treatment. The storage pile drainage was diluted, however, by large volumes of alkaline water in the settling pond. Analysis of overburden and coal indicated that the major impact of mine drainage was pyrite oxidation and hydrolysis in the Middle Kittanning Coal and in the Lower Freeport Shale overlying the coal. However, the presence of a calcite-cemented section in the Upper Freeport Sandstone contributed substantial self-neutralizing capacity to the overburden section, resulting in generally alkaline drainage at this site.

  16. A river to ruin : why are Americans fighting so hard to protect British Columbia's Flathead River from a strip mine?

    Energy Technology Data Exchange (ETDEWEB)

    Hull, J.

    2008-06-15

    The Cline Mining Corporation has proposed an open-pit mine to extract 2 million tonnes of coal annually in the Flathead Valley of British Columbia (BC). The Flathead Valley is known internationally for the richness of its flora and fauna. After the Flathead River crosses the border into Montana, it is managed under the most restrictive environmental protection laws available in the United States. The project is expected to be the first in a series of energy projects that will ravage the valley in the near future. Major energy companies are planning to open mines at sites within the Flathead River flood plain. The low quality coal obtained from the valley will be used to supply the unregulated economies of China, India, and Brazil. The valley is situated at the convergence of several biogeoclimatic zones and is home to a rich mix of plants and animals, including the highest concentration of grizzly bears in North America. The BC government's regulatory mechanism is not able to prevent exploitation of the region. Scientists from around the world have unanimously agreed that the mine should not be opened. Tailings from other mines currently draining into the Flathead River are now beginning to alter the river's chemistry. The federal government has been unsuccessful in its bid to create a national park in the region. It was concluded that unless land use regulations for the area are changed, the valley will inevitably be developed. 13 figs.

  17. Reclamation of acid, toxic coal spoils using wet flue gas desulfurization by-product, fly ash and sewage sludge. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kost, D.A.; Vimmerstedt, J.P.; Stehouwer, R.C.

    1997-03-01

    Establishment of vegetation on acid abandoned minelands requires modification of soil physical and chemical conditions. Covering the acid minesoil with topsoil or borrow soil is a common practice but this method may be restricted by availability of borrow soil and cause damage to the borrow site. An alternative approach is to use waste materials as soil amendments. There is a long history of using sewage sludge and fly ash as amendments for acid minesoils. Flue gas desulfurization (FGD) by-products are newer materials that are also promising amendments. Most flue gas sludges are mixtures of Calcium sulfate (CaSO{sub 4}), calcium sulfite (CaSO{sub 3}), calcium carbonate (CaCO{sub 3}), calcium hydroxide [Ca(OH){sub 2}], and fly ash. Some scrubbing processes produce almost pure gypsum (CaSO{sub 4}2H{sub 2}O). The primary purpose of the project is to evaluate two wet FGD by-products for effects on vegetation establishment and surface and ground water quality on an acid minesoil. One by-product from the Conesville, OH power plant (American Electric Power Service Corporation) contains primarily calcium sulfite and fly ash. The other by-product (Mg-gypsum FGD) from an experimental scrubber at the Zimmer power plant (Cincinnati Gas and Electric Company) is primarily gypsum with 4% magnesium hydroxide. These materials were compared with borrow soil and sewage sludge as minesoil amendments. Combinations of each FGD sludge with sewage sludge were also tested. This report summarizes two years of measurements of chemical composition of runoff water, ground water at two depths in the subsoil, soil chemical properties, elemental composition and yield of herbaceous ground cover, and elemental composition, survival and height of trees planted on plots treated with the various amendments. The borrow soil is the control for comparison with the other treatments.

  18. Reclamation of acid, toxic coal spoils using wet flue gas desulfurization by-product, fly ash and sewage sludge. Final report

    International Nuclear Information System (INIS)

    Kost, D.A.; Vimmerstedt, J.P.; Stehouwer, R.C.

    1997-03-01

    Establishment of vegetation on acid abandoned minelands requires modification of soil physical and chemical conditions. Covering the acid minesoil with topsoil or borrow soil is a common practice but this method may be restricted by availability of borrow soil and cause damage to the borrow site. An alternative approach is to use waste materials as soil amendments. There is a long history of using sewage sludge and fly ash as amendments for acid minesoils. Flue gas desulfurization (FGD) by-products are newer materials that are also promising amendments. Most flue gas sludges are mixtures of Calcium sulfate (CaSO 4 ), calcium sulfite (CaSO 3 ), calcium carbonate (CaCO 3 ), calcium hydroxide [Ca(OH) 2 ], and fly ash. Some scrubbing processes produce almost pure gypsum (CaSO 4 2H 2 O). The primary purpose of the project is to evaluate two wet FGD by-products for effects on vegetation establishment and surface and ground water quality on an acid minesoil. One by-product from the Conesville, OH power plant (American Electric Power Service Corporation) contains primarily calcium sulfite and fly ash. The other by-product (Mg-gypsum FGD) from an experimental scrubber at the Zimmer power plant (Cincinnati Gas and Electric Company) is primarily gypsum with 4% magnesium hydroxide. These materials were compared with borrow soil and sewage sludge as minesoil amendments. Combinations of each FGD sludge with sewage sludge were also tested. This report summarizes two years of measurements of chemical composition of runoff water, ground water at two depths in the subsoil, soil chemical properties, elemental composition and yield of herbaceous ground cover, and elemental composition, survival and height of trees planted on plots treated with the various amendments. The borrow soil is the control for comparison with the other treatments

  19. Contrast Materials

    Science.gov (United States)

    ... is mixed with water before administration liquid paste tablet When iodine-based and barium-sulfate contrast materials ... for patients with kidney failure or allergies to MRI and/or computed tomography (CT) contrast material. Microbubble ...

  20. Role of complex utilization of mineral raw materials In geological research

    Energy Technology Data Exchange (ETDEWEB)

    Takacs, P.; Varju, G.

    1979-01-01

    Presents Hungarian research efforts on ways of utilizing the secondary raw materials alunite, pumice and slate coal from various mines. The slate coal is separated from brown coal and disposed of at spoil banks of brown coal mines, due to its high ash content (up to 56.8% under dry conditions), silicate content up to 58.2% and low calorific value between 1500 and 2780 kcal/kg. The research proposal for utilizing slate coal is directed at partial separation of the mineral and coal content by comminution, peptization and hydrocentrifugal separation. The larger part of the silicate content is held in the colloid suspension, which could be used for conditioning drilling mud or foundry sand. The produced coal concentrate has a reduced ash content and higher calorific value (between 500 and 800 kcal/kg) and could be employed in soil amelioration or combustion. (10 refs.) (In German)

  1. Dirac materials

    OpenAIRE

    Wehling, T. O.; Black-Schaffer, A. M.; Balatsky, A. V.

    2014-01-01

    A wide range of materials, like d-wave superconductors, graphene, and topological insulators, share a fundamental similarity: their low-energy fermionic excitations behave as massless Dirac particles rather than fermions obeying the usual Schrodinger Hamiltonian. This emergent behavior of Dirac fermions in condensed matter systems defines the unifying framework for a class of materials we call "Dirac materials''. In order to establish this class of materials, we illustrate how Dirac fermions ...

  2. Magnetic Materials

    Science.gov (United States)

    Spaldin, Nicola A.

    2003-04-01

    Magnetic materials are the foundation of multi-billion dollar industries and the focus of intensive research across many disciplines. This book covers the fundamentals, basic theories and applications of magnetism and conventional magnetic materials. Based on a lecture course given by Nicola Spaldin in the Materials Department at University of California, Santa Barbara, the book is ideal for a one- semester course in magnetic materials. It contains numerous homework problems and solutions.

  3. Energy, materials and water in industrial activities in Galicia (Spain); Energia, Materiales y Agua en la Industria Manufacturera Gallega

    Energy Technology Data Exchange (ETDEWEB)

    Doldan Garcia, X. R.

    2003-07-01

    The Galicia industrial activities request a big amount of raw materials energy and water, generating several kinds of residues. Most of them directly spoil the environment, causing important damages. Furthermore, the primary energy self supply capacity doesn't exist at this moment, being substituted by high levels of energetic resources importations satisfying industrial demand without decreasing the electricity and petroleum products exportations. This article tries to develop a complete analysis of this kind of problems, making an approach to the environmental situation of the Galicia manufacturing industry through materials, energy and water flow models. It focuses in those sectors which have a remarkable production within the Galicia industry, analysing their situation in two different years, 1992 and 2000. This will allow to identify possible tendencies of the industry as a whole, like a relative dematerialization, followed by a complete rematerialization.

  4. Composite materials

    International Nuclear Information System (INIS)

    Sambrook, D.J.

    1976-01-01

    A superconductor composite is described comprising at least one longitudinally extending superconductor filament or bundle of sub-filaments, each filament or bundle of sub-filaments being surrounded by and in good electrical contact with a matrix material, the matrix material comprising a plurality of longitudinally extending cells of a metal of high electrical conductivity surrounded by a material of lower electrical conductivity. The high electrical conductivity material surrounding the superconducting filament or bundle of sub-filaments is interrupted by a radially extending wall of the material of the lower electrical conductivity, the arrangement being such that at least two superconductor filaments or sub-filaments are circumferentially circumscribed by a single annulus of the material of high electrical conductivity. The annulus is electrically interrupted by a radially extending wall of the material of low electrical conductivity

  5. Aerospace materials and material technologies

    CERN Document Server

    Wanhill, R

    2017-01-01

    This book is a comprehensive compilation of chapters on materials (both established and evolving) and material technologies that are important for aerospace systems. It considers aerospace materials in three Parts. Part I covers Metallic Materials (Mg, Al, Al-Li, Ti, aero steels, Ni, intermetallics, bronzes and Nb alloys); Part II deals with Composites (GLARE, PMCs, CMCs and Carbon based CMCs); and Part III considers Special Materials. This compilation has ensured that no important aerospace material system is ignored. Emphasis is laid in each chapter on the underlying scientific principles as well as basic and fundamental mechanisms leading to processing, characterization, property evaluation and applications. A considerable amount of materials data is compiled and presented in appendices at the end of the book. This book will be useful to students, researchers and professionals working in the domain of aerospace materials.

  6. Materials Discovery | Materials Science | NREL

    Science.gov (United States)

    Discovery Materials Discovery Images of red and yellow particles NREL's research in materials characterization of sample by incoming beam and measuring outgoing particles, with data being stored and analyzed Staff Scientist Dr. Zakutayev specializes in design of novel semiconductor materials for energy

  7. Mathematical modelling of transport of gaseous and liquid substances induced by pyrite oxidation in spoil banks of lignite mines; Mathematische Modellierung der durch Pyritoxidation induzierten Stofftransporte in Braunkohleabraumkippen in gasfoermiger und fluessiger Phase

    Energy Technology Data Exchange (ETDEWEB)

    Ludwig, R.

    2001-07-01

    Pyrite (FeS{sub 2}) oxidation due to open-pit lignite mining activities may result in acid mine drainage and dissolved metals in the soil and ground water of the overburden spoil piles. The pyrite oxidation takes place firstly during the mining process and at the temporary surfaces of the mine, secondly in deep zones of the overburden spoil pile as a result of gas transport through the unsaturated zone. The second process continues after mine closure possibly over several decades and therefore contaminates the environment for a long time. Whereas some studies deal with a minimisation by geochemical means, this research focuses on a minimisation by impacting the physical boundary conditions. Special attention is given to the transport of oxygen from the soil surface to the pyrite oxidation zone. Soil column experiments with columns of 2.90 m height yield experimental data concerning the pyrite oxidation and the related transport processes in the unsaturated zone. Experimental data are compared to simulation results obtained with the model MUSIC; it calculates coupled reaction and transport processes in a one-dimensional soil profile using the finite volume method. Pyrite oxidation is described by means of a first order kinetics, the gas transport takes place by diffusion as well as convection. The transport of solutes in the soil water is described by the convection-dispersion equation (Cl{sup -}, Fe{sup 2+} and SO{sub 4}{sup 2-}). The simulations are able to reproduce the measured time series of oxygen concentrations in the soil profile. (orig.) [German] Die durch Braunkohlegewinnung im Tagebau hervorgerufene Pyritoxidation (Pyrit: FeS{sub 2}) kann zu Versauerung, Schwermetallfreisetzung und Aufmineralisierung des Boden- und Grundwassers in den Abraumkippen fuehren. Die Pyritoxidation findet zum einen waehrend des Abbaubetriebs und an den temporaeren Oberflaechen des Tagebaus statt, zum anderen in tieferen Bereichen der Abraumkippe durch Gastransport durch die

  8. Myocardial T1 mapping at 3.0 tesla using an inversion recovery spoiled gradient echo readout and bloch equation simulation with slice profile correction (BLESSPC) T1 estimation algorithm.

    Science.gov (United States)

    Shao, Jiaxin; Rapacchi, Stanislas; Nguyen, Kim-Lien; Hu, Peng

    2016-02-01

    To develop an accurate and precise myocardial T1 mapping technique using an inversion recovery spoiled gradient echo readout at 3.0 Tesla (T). The modified Look-Locker inversion-recovery (MOLLI) sequence was modified to use fast low angle shot (FLASH) readout, incorporating a BLESSPC (Bloch Equation Simulation with Slice Profile Correction) T1 estimation algorithm, for accurate myocardial T1 mapping. The FLASH-MOLLI with BLESSPC fitting was compared with different approaches and sequences with regards to T1 estimation accuracy, precision and image artifact based on simulation, phantom studies, and in vivo studies of 10 healthy volunteers and three patients at 3.0 Tesla. The FLASH-MOLLI with BLESSPC fitting yields accurate T1 estimation (average error = -5.4 ± 15.1 ms, percentage error = -0.5% ± 1.2%) for T1 from 236-1852 ms and heart rate from 40-100 bpm in phantom studies. The FLASH-MOLLI sequence prevented off-resonance artifacts in all 10 healthy volunteers at 3.0T. In vivo, there was no significant difference between FLASH-MOLLI-derived myocardial T1 values and "ShMOLLI+IE" derived values (1458.9 ± 20.9 ms versus 1464.1 ± 6.8 ms, P = 0.50); However, the average precision by FLASH-MOLLI was significantly better than that generated by "ShMOLLI+IE" (1.84 ± 0.36% variance versus 3.57 ± 0.94%, P < 0.001). The FLASH-MOLLI with BLESSPC fitting yields accurate and precise T1 estimation, and eliminates banding artifacts associated with bSSFP at 3.0T. © 2015 Wiley Periodicals, Inc.

  9. Nano Materials

    International Nuclear Information System (INIS)

    Jin, In Ju; Lee, Ik Mo; Kwon, Yeung Gu

    2006-02-01

    This book introduces background of nano science such as summary, plenty room at the bottom, access way to nano technique, nanoparticles using bottom-up method which are a marvel of nature, and modern alchemy : chemical synthesis of artificial nano structure, understanding of quantum mechanics, STM/AFM, nano metal powder, ceramic nanoparticles, nano structure film, manufacture of nanoparticles using reverse micelle method, carbon nano tube, sol-gel material, nano energy material, nano catalyst nano bio material technology and spintronics.

  10. Material Systems

    DEFF Research Database (Denmark)

    Jensen, Mads Brath; Mortensen, Henrik Rubæk; Mullins, Michael

    2009-01-01

    This paper describes and reflects upon the results of an investigative project which explores the setting up of a material system - a parametric and generative assembly consisting of and taking into consideration material properties, manufacturing constraints and geometric behavior. The project...... approaches the subject through the construction of a logic-driven system aiming to explore the possibilities of a material system that fulfills spatial, structural and performative requirements concurrently and how these are negotiated in situations where they might be conflicting....

  11. Material focus

    DEFF Research Database (Denmark)

    Sokoler, Tomas; Vallgårda, Anna K. A.

    2009-01-01

    In this paper we build on the notion of computational composites, which hold a material perspective on computational technology. We argue that a focus on the material aspects of the technology could be a fruitful approach to achieve new expressions and to gain a new view on the technology's role...... in design. We study two of the computer's material properties: computed causality and connectability and through developing two computational composites that utilize these properties we begin to explore their potential expressions....

  12. Materializing Ethnography

    OpenAIRE

    Geismar, H.; Horst, H. A.

    2004-01-01

    The articles in this volume were originally presented in a panel entitled ‘Material Methodologies’ at the American Anthropological Association meeting in New Orleans (November 2002). The panel was devised to tie together theoretical advances in the study of the material with the creative possibilities of fieldwork practices. Through detailed ethnographic discussion, we highlighted the ways in which a focus on a specifically material world enabled us to discover new perspecti...

  13. Materials characterisation

    International Nuclear Information System (INIS)

    Azali Muhammad

    2005-01-01

    Various nuclear techniques have been developed and employed by technologies and scientists worldwide to physically and chemically characterise the material particularly those that have applications in industry. These include small angle neutron scattering (SANS), x-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM) for the internal structural study of material, whereas, the x-ray fluorescence (XRF) for the chemical analysis, while the Moessbauer spectroscopy for the study on the magnetic properties and structural identity of material. Basic principle and instrumentations of the techniques are discussed in this chapter. Example of their applications in various disciplines particularly in characterisation of industrial materials also described

  14. New materials

    International Nuclear Information System (INIS)

    Joshi, S.K.; Rao, C.N.R.; Tsuruta, T.

    1992-01-01

    The book contains the state-of-the art lectures delivered at the discussion meeting on new materials, a field in which rapid advances are taking place. The main objective of the meeting was to bring active scientists in this area from Japan and India together. The topics covered diverse aspects of modern materials including high temperature superconducting compounds. (M.G.B.)

  15. Materials science

    International Nuclear Information System (INIS)

    2002-01-01

    the document is a collection of papers on different aspects of materials science. It discusses many items such as semiconductors, surface properties and interfaces, construction and civil engineering, metallic materials, polymers and composites, biology and biomaterials, metallurgy etc.. - 1 - Document1 Document1

  16. Comparison of T1rho imaging between spoiled gradient echo (SPGR) and balanced steady state free precession (b-FFE) sequence of knee cartilage at 3 T MRI

    Energy Technology Data Exchange (ETDEWEB)

    Nozaki, Taiki; Kaneko, Yasuhito; Yu, Hon J. [Department of Radiological Sciences, University of California, Irvine, CA (United States); Kaneshiro, Kayleigh [School of Medicine, University of California, Irvine, CA (United States); Schwarzkopf, Ran [Department of Orthopaedic Surgery, University of California, Irvine, CA (United States); Yoshioka, Hiroshi, E-mail: hiroshi@uci.edu [Department of Radiological Sciences, University of California, Irvine, CA (United States)

    2015-07-15

    Highlights: • T1rho values on b-FFE tend to be higher than those on SPGR. • The reproducibility of T1rho cartilage segmentation is higher on SPGR than b-FFE. • There is angular variation of T1rho profiles. • Average T1rho values in the superficial layer are higher than in the deep layer. - Abstract: Purpose: To investigate the difference in T1rho profiles of the entire femoral cartilage between SPGR and b-FFE sequences at 3.0 T. Materials and methods: 20 healthy volunteers were enrolled in this study. T1rho images of each subject were acquired with two types of pulse sequences: SPGR and b-FFE. Femoral cartilage segmentation was performed by two independent raters slice-by-slice using Matlab. Inter- and intra-observer reproducibility between the two imaging protocols was calculated. The relative signal intensity (SI) of cartilage, subchondral bone marrow, joint effusion, and the relative signal contrast between structures of the knee were quantitatively measured. The difference in T1rho values between SPGR and b-FFE sequences was statistically analyzed using the Wilcoxon signed-rank test. Results: The average T1rho value of the entire femoral cartilage with b-FFE was significantly higher compared to SPGR (p < 0.05). The reproducibility of the segmented area and T1rho values was superior with SPGR compared to b-FFE. The inter-class correlation coefficient was 0.846 on SPGR and 0.824 on b-FFE. The intra-class correlation coefficient of T1rho values was 0.878 on SPGR and 0.836 on b-FFE. The two imaging techniques demonstrated different signal and contrast characteristics. The relative SI of fluid was significantly higher on SPGR, while the relative SI of subchondral bone was significantly higher on b-FFE (p < 0.001). There were also significant differences in the relative contrast between fluid–cartilage, fluid–subchondral bone, and cartilage–subchondral bone between the two sequences (all p < 0.001). Conclusion: We need to pay attention to differences in

  17. Material Programming

    DEFF Research Database (Denmark)

    Vallgårda, Anna; Boer, Laurens; Tsaknaki, Vasiliki

    2017-01-01

    . Consequently we ask what the practice of programming and giving form to such materials would be like? How would we be able to familiarize ourselves with the dynamics of these materials and their different combinations of cause and effect? Which tools would we need and what would they look like? Will we program......, and color, but additionally being capable of sensing, actuating, and computing. Indeed, computers will not be things in and by themselves, but embedded into the materials that make up our surroundings. This also means that the way we interact with computers and the way we program them, will change...... these computational composites through external computers and then transfer the code them, or will the programming happen closer to the materials? In this feature we outline a new research program that floats between imagined futures and the development of a material programming practice....

  18. Composite material

    Science.gov (United States)

    Hutchens, Stacy A [Knoxville, TN; Woodward, Jonathan [Solihull, GB; Evans, Barbara R [Oak Ridge, TN; O'Neill, Hugh M [Knoxville, TN

    2012-02-07

    A composite biocompatible hydrogel material includes a porous polymer matrix, the polymer matrix including a plurality of pores and providing a Young's modulus of at least 10 GPa. A calcium comprising salt is disposed in at least some of the pores. The porous polymer matrix can comprise cellulose, including bacterial cellulose. The composite can be used as a bone graft material. A method of tissue repair within the body of animals includes the steps of providing a composite biocompatible hydrogel material including a porous polymer matrix, the polymer matrix including a plurality of pores and providing a Young's modulus of at least 10 GPa, and inserting the hydrogel material into cartilage or bone tissue of an animal, wherein the hydrogel material supports cell colonization in vitro for autologous cell seeding.

  19. Materials science

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    The Materials Science Division is engaged in research on physical properties of materials and the effects of radiation upon them. This involves solid state materials undergoing phase transitions, energy storing materials, and biomaterials. The Division also offers research facilities for M.S. and Ph.D. thesis work in the fields of physics, chemistry, materials, and radiation sciences in cooperation with the various colleges and departments of the UPR Mayaguez Campus. It is anticipated that it will serve as a catalyst in starting energy-related research programs in cooperation with UPR faculty, especially programs involving solar energy. To encourage and promote cooperative efforts, contact is maintained with former graduate students and with visiting scientists from Latin American research institutions

  20. Touching Materiality

    DEFF Research Database (Denmark)

    Rasmussen, Lisa Rosén

    2012-01-01

    Dripping ink pens, colourful paint on skin, vegetables pots on a school roof. In interviews with three generations of former school pupils, memories of material objects bore a relation to everyday school life in the past. Interwoven, these objects entered the memorising processes, taking...... the interviewer and interviewee beyond an exclusively linguistic understanding of memory. This article analyses how the shifting objects of materiality in personal and generational school memories connects to material as well as sensuous experiences of everyday school life and its complex processes of learning....... Drawing on anthropological writings, the article argues that the objects of materiality are part of important but non-verbalised memories of schooling. The Dutch philosopher Eelco Runia’s notions of presence and metonymy are incorporated as tools for approaching objects of materiality in memory studies....

  1. Nuclear materials

    International Nuclear Information System (INIS)

    1996-01-01

    In 1998, Nuclear Regulatory Authority of the Slovak Republic (NRA SR) performed 38 inspections, 25 of them were performed in co-operation with IAEA inspectors. There is no fresh nuclear fuel at Bohunice A-1 NPP at present. Fresh fuel of Bohunice V-1 and V-2 NPPs is inspected in the fresh fuel storage.There are 327 fresh fuel assemblies in Mochovce NPP fresh fuel storage. In addition to that, are also 71 small users of nuclear materials in Slovakia. In most cases they use: covers made of depleted uranium for non-destructive works, detection of level in production plants, covers for therapeutical sources at medical facilities. In. 1995, NRA SR issued 4 new licences for nuclear material withdrawal. In the next part manipulation with nuclear materials, spent fuel stores and illegal trafficking in nuclear materials are reported

  2. Composite Materials

    DEFF Research Database (Denmark)

    Nielsen, Lauge Fuglsang

    This book deals with the mechanical and physical behavior of composites as influenced by composite geometry. "Composite Materials" provides a comprehensive introduction for researchers and students to modern composite materials research with a special emphasis on the significance of phase geometry......, viscoelastic behavior, and internal stress states. Other physical properties considered are thermal and electrical conductivities, diffusion coefficients, dielectric constants and magnetic permeability. Special attention is given to the effect of pore shape on the mechanical and physical behavior of porous....... The book enables the reader to a better understanding of the behavior of natural composites, improvement of such materials, and design of new materials with prescribed properties. A number of examples are presented: Special composite properties considered are stiffness, shrinkage, hygro-thermal behavior...

  3. Hazardous materials

    Science.gov (United States)

    ... substances that could harm human health or the environment. Hazardous means dangerous, so these materials must be ... M. is also a founding member of Hi-Ethics and subscribes to the principles of the Health ...

  4. Utopian Materialities

    DEFF Research Database (Denmark)

    Elgaard-Jensen, Torben

    2004-01-01

    In various ways, this paper makes the counter-intuitive claim that the utopian and the material are thoroughlyinterdependent, rather than worlds apart. First, through a reading of Thomas More's Utopia, it is argued thatUtopia is the product of particular kinds of relations, rather than merely...... a detachment from the known world.Second, the utopianism of a new economy firm is examined. It is argued that the physical set-up of the firm -in particular the distribution of tables and chairs - evoke a number of alternatives to ordinary work practice.In this way the materialities of the firm are crucial...... to its persuasive image of being the office of the future.The notion that utopia is achieved through material arrangements is finally related to the analysis of facts andfictions in ANT. It is argued, that even though Utopias are neither fact nor fiction, they are both material andeffective...

  5. Propulsion materials

    Energy Technology Data Exchange (ETDEWEB)

    Wall, Edward J. [U.S. Dept. of Energy, Washington, D.C. (United States); Sullivan, Rogelio A. [U.S. Dept. of Energy, Washington, D.C. (United States); Gibbs, Jerry L. [U.S. Dept. of Energy, Washington, D.C. (United States)

    2008-01-01

    The Department of Energy’s (DOE’s) Office of Vehicle Technologies (OVT) is pleased to introduce the FY 2007 Annual Progress Report for the Propulsion Materials Research and Development Program. Together with DOE national laboratories and in partnership with private industry and universities across the United States, the program continues to engage in research and development (R&D) that provides enabling materials technology for fuel-efficient and environmentally friendly commercial and passenger vehicles.

  6. Encountering Materiality

    DEFF Research Database (Denmark)

    Svabo, Connie

    2016-01-01

    DHT researcher Connie Svabo and artist Charlotte Grum did a joint performance presentation titled Becoming Sheep, Becoming Animal at the international conference Encountering Materiality – Transdisciplinary Conversations, held in Geneve, Schwitzerland, June 23-25 2016.......DHT researcher Connie Svabo and artist Charlotte Grum did a joint performance presentation titled Becoming Sheep, Becoming Animal at the international conference Encountering Materiality – Transdisciplinary Conversations, held in Geneve, Schwitzerland, June 23-25 2016....

  7. Background Material

    DEFF Research Database (Denmark)

    Zandersen, Marianne; Hyytiäinen, Kari; Saraiva, Sofia

    This document serves as a background material to the BONUS Pilot Scenario Workshop, which aims to develop harmonised regional storylines of socio-ecological futures in the Baltic Sea region in a collaborative effort together with other BONUS projects and stakeholders.......This document serves as a background material to the BONUS Pilot Scenario Workshop, which aims to develop harmonised regional storylines of socio-ecological futures in the Baltic Sea region in a collaborative effort together with other BONUS projects and stakeholders....

  8. Experimental and Theoretical Investigations of the Impact Localization of a Passive Smart Composite Plate Fabricated Using Piezoelectric Materials

    Directory of Open Access Journals (Sweden)

    M. M. S. Dezfouli

    2013-01-01

    Full Text Available Two passive smart composite plates are fabricated using one and two PZT patches that are cheaper than the PZT wafer. The composite plate is fabricated in low temperature through the hand lay-up method to avoid PZT patch decoupling and wire spoiling. The locus of the impact point is identified using the output voltage to identify the impact location using one sensor. The output voltages of the sensors are analyzed to identify the impact location using two sensors. The locations of the impacts are determined based on the crossing points of two circles and the origin of an intended Cartesian coordinate system that is concentric with one of the sensors. This study proposes the impact location identification of the passive smart composite using the low-cost PZT patch PIC155 instead of common embedded materials (wafer and element piezoelectric.

  9. Layered materials

    Science.gov (United States)

    Johnson, David; Clarke, Simon; Wiley, John; Koumoto, Kunihito

    2014-06-01

    Layered compounds, materials with a large anisotropy to their bonding, electrical and/or magnetic properties, have been important in the development of solid state chemistry, physics and engineering applications. Layered materials were the initial test bed where chemists developed intercalation chemistry that evolved into the field of topochemical reactions where researchers are able to perform sequential steps to arrive at kinetically stable products that cannot be directly prepared by other approaches. Physicists have used layered compounds to discover and understand novel phenomena made more apparent through reduced dimensionality. The discovery of charge and spin density waves and more recently the remarkable discovery in condensed matter physics of the two-dimensional topological insulating state were discovered in two-dimensional materials. The understanding developed in two-dimensional materials enabled subsequent extension of these and other phenomena into three-dimensional materials. Layered compounds have also been used in many technologies as engineers and scientists used their unique properties to solve challenging technical problems (low temperature ion conduction for batteries, easy shear planes for lubrication in vacuum, edge decorated catalyst sites for catalytic removal of sulfur from oil, etc). The articles that are published in this issue provide an excellent overview of the spectrum of activities that are being pursued, as well as an introduction to some of the most established achievements in the field. Clusters of papers discussing thermoelectric properties, electronic structure and transport properties, growth of single two-dimensional layers, intercalation and more extensive topochemical reactions and the interleaving of two structures to form new materials highlight the breadth of current research in this area. These papers will hopefully serve as a useful guideline for the interested reader to different important aspects in this field and

  10. Electronic materials

    CERN Document Server

    Kwok, H L

    2010-01-01

    The electronic properties of solids have become of increasing importance in the age of information technology. The study of solids and materials, while having originated from the disciplines of physics and chemistry, has evolved independently over the past few decades. The classical treatment of solid-state physics, which emphasized classifications, theories and fundamental physical principles, is no longer able to bridge the gap between materials advances and applications. In particular, the more recent developments in device physics and technology have not necessarily been driven by new conc

  11. Too many cooks spoil the broth?

    DEFF Research Database (Denmark)

    Rørbæk, Anne

    To collaborate across organisational contexts is not an easy task, but to do so and to succeed can be vital for reaching creative and innovative results. This paper is an empirical exploration of contextual challenges for collaborative museum design, focusing on the interplay between museums and ...... and ICT design companies. Based on empirical findings, two kinds of challenges are presented as particularly interesting in relation to this context: Structure related challenges, and value and practice related challenges....

  12. Toxigenic penicillia spoiling frozen chicken nuggets

    DEFF Research Database (Denmark)

    Wigmann, Evelin Francine; Saccomori, Fernanda; Bernardi, Angelica Olivier

    2015-01-01

    Frozen chicken nuggets are classified as pre-prepared frozen meals. These products are convenient to consumers as they are easy to prepare and allow for long storage by freezing. Over the years, spoilage of frozen food products caused by fungi has been a continual problem for the food industry...... of filamentous fungi involved in the spoilage of frozen chicken nuggets and determine their ability to produce mycotoxins under laboratorial conditions. A total of 7 samples of frozen chicken nuggets were analyzed by dilution plating in potato dextrose agar (PDA). These products had been returned by customers...

  13. Spoiled Onions: Exposing Malicious Tor Exit Relays

    OpenAIRE

    Winter, Philipp; Lindskog, Stefan

    2014-01-01

    Several hundred Tor exit relays together push more than 1 GiB/s of network traffic. However, it is easy for exit relays to snoop and tamper with anonymised network traffic and as all relays are run by independent volunteers, not all of them are innocuous. In this paper, we seek to expose malicious exit relays and document their actions. First, we monitored the Tor network after developing a fast and modular exit relay scanner. We implemented several scanning modules for detecting common attac...

  14. Cheating More when the Spoils Are Split

    Science.gov (United States)

    Wiltermuth, Scott S.

    2011-01-01

    Four experiments demonstrated that people are more likely to cheat when the benefits of doing so are split with another person, even an anonymous stranger, than when the actor alone captures all of the benefits. In three of the studies, splitting the benefits of over-reporting one's performance on a task made such over-reporting seem less…

  15. Spare the rod and spoil the eye

    NARCIS (Netherlands)

    Arden, G. B.; Sidman, R. L.; Arap, W.; Schlingemann, R. O.

    2005-01-01

    This review presents a new unified view of the pathogenesis of three common causes of acquired retinal degenerative disease - diabetic retinopathy, age related macular degeneration, and retinopathy of prematurity. In these three conditions, angiogenesis has a predominant role in the development of

  16. Supplementary Material

    Indian Academy of Sciences (India)

    mraga

    1. Supplementary Material. A soluble-lead Redox Flow Battery with corrugated graphite sheet and reticulated vitreous carbon as positive and negative current collectors by A Banerjee et al (pp 163-. 170). Figure S1. SEM images for bare substrates: (a) graphite sheet, (b) 20 ppi RVC, (c) 30 ppi. RVC and (d) 45 ppi RVC.

  17. Emerging Materiality

    DEFF Research Database (Denmark)

    Bertelsen, Olav Wedege; Breinbjerg, Morten; Pold, Søren

    2009-01-01

    The authors examine how materiality emerges from complex chains of mediation in creative software use. The primarily theoretical argument is inspired and illustrated by interviews with two composers of electronic music. The authors argue that computer mediated activity should not primarily be und...

  18. Atmospheric materiality

    DEFF Research Database (Denmark)

    Wieczorek, Izabela

    2016-01-01

    experience and, consequently, to the conceptual and methodological shifts in the production of space, and hence in the way we think about materiality. In this context, architectural space is understood as a contingent construction – a space of engagement that appears to us as a result of continuous...

  19. Absorbant materials

    International Nuclear Information System (INIS)

    Quetier, Monique.

    1978-11-01

    Absorbants play a very important part in the nuclear industry. They serve for the control, shut-down and neutron shielding of reactors and increase the capacity of spent fuel storage pools and of special transport containers. This paper surveys the usual absorbant materials, means of obtainment, their essential characteristics relating to their use and their behaviour under neutron irradiation [fr

  20. Friction Material Composites Materials Perspective

    CERN Document Server

    Sundarkrishnaa, K L

    2012-01-01

    Friction Material Composites is the first of the five volumes which strongly educates and updates engineers and other professionals in braking industries, research and test labs. It explains besides the formulation of design processes and its complete manufacturing input. This book gives an idea of mechanisms of friction and how to control them by designing .The book is  useful for designers  of automotive, rail and aero industries for designing the brake systems effectively with the integration of friction material composite design which is critical. It clearly  emphasizes the driving  safety and how serious designers should  select the design input. The significance of friction material component like brake pad or a liner as an integral part of the brake system of vehicles is explained. AFM pictures at nanolevel illustrate broadly the explanations given.

  1. Materials Science

    Science.gov (United States)

    2003-01-01

    The Materials Science Program is structured so that NASA s headquarters is responsible for the program content and selection, through the Enterprise Scientist, and MSFC provides for implementation of ground and flight programs with a Discipline Scientist and Discipline Manager. The Discipline Working Group of eminent scientists from outside of NASA acts in an advisory capacity and writes the Discipline Document from which the NRA content is derived. The program is reviewed approximately every three years by groups such as the Committee on Microgravity Research, the National Materials Advisory Board, and the OBPR Maximization and Prioritization (ReMaP) Task Force. The flight program has had as many as twenty-six principal investigators (PIs) in flight or flight definition stage, with the numbers of PIs in the future dependent on the results of the ReMaP Task Force and internal reviews. Each project has a NASA-appointed Project Scientist, considered a half-time job, who assists the PI in understanding and preparing for internal reviews such as the Science Concept Review and Requirements Definition Review. The Project Scientist also insures that the PI gets the maximum science support from MSFC, represents the PI to the MSFC community, and collaborates with the Project Manager to insure the project is well-supported and remains vital. Currently available flight equipment includes the Materials Science Research Rack (MSRR-1) and Microgravity Science Glovebox. Ground based projects fall into one or more of several categories. Intellectual Underpinning of Flight Program projects include theoretical studies backed by modeling and computer simulations; bring to maturity new research, often by young researchers, and may include preliminary short duration low gravity experiments in the KC-135 aircraft or drop tube; enable characterization of data sets from previous flights; and provide thermophysical property determinations to aid PIs. Radiation Shielding and preliminary In

  2. Magnetocaloric materials

    Energy Technology Data Exchange (ETDEWEB)

    Jeppesen, Stinus

    2008-10-15

    New and improved magnetocaloric materials are one of the cornerstones in the development of room temperature magnetic refrigeration. Magnetic refrigeration has been used since the 1930ies in cryogenic applications, but has since the discovery of room temperature refrigerants received enormous attention. This Ph.D. work has been mainly concerned with developing a new technique to characterize the magnetocaloric effect (MCE) and using this technique in the investigations on new and improved magnetocaloric materials. For this purpose a novel differential scanning calorimeter (DSC) with applied magnetic fields was developed for measuring heat capacity as function of magnetic field. Measurements using the developed DSC demonstrate a very high sensitivity, fast measurements and good agreement with results obtained by other techniques. Furthermore, two material systems have been described in this work. Both systems take basis in the mixed-valence manganite system La{sub 1-x}Ca{sub x}MnO{sub 3} well known from research on colossal magnetoresistance (CMR). The mixed-valence manganite crystallizes in the perovskite structure of general formula ABO{sub 3}. The first material system is designed to investigate the influence of low level Cu doping on the B-site. Six different samples were prepared with over-stoichiometric compositions La{sub 0.67}Ca{sub 0.33}Mn{sub 1.05}Cu{sub x}O{sub 3}, x=0, 1, 2, 3, 4 and 5%. All compositions crystallized well in the same perovskite structure, but the morphology of the samples changed drastically with doping. Investigation on the magnetocaloric properties revealed that small levels of Cu up to around 3% could improve the magnetocaloric performance of the materials. Furthermore, Cu could be used to tune the temperature interval without deteriorating the MCE, which is a much desired characteristic for potential use in magnetic refrigerators. A less comprehensive part of the work has been concerned with the investigation of doping on the A

  3. Materializing Superghosts

    OpenAIRE

    Alexandrov, Victor; Krotov, Dmitry; Losev, Andrei; Lysov, Vyacheslav

    2007-01-01

    We construct the off-shell BV realization of N=1, d=10 SYM with 7 auxillary fields. This becomes possible due to materialized ghost phenomenon. Namely, supersymmetry ghosts are coordinates on a manifold B of 10-dimensional spinors with pure spinors cut out. Auxillary fields are sections of a bundle over B, and supersymmetry transformations are nonlinear in ghosts. By integrating out axillary fields we obtain on-shell supersymmetric BV action with terms quadratic in antifields. Exactly this on...

  4. Material monitoring

    International Nuclear Information System (INIS)

    Kotter, W.; Zirker, L.; Hancock, J.A.

    1995-01-01

    Waste Reduction Operations Complex (WROC) facilities are located at the Idaho National Engineering Laboratory (INEL). The overall goal for the Pollution Prevention/Waste Minimization Unit is to identify and establish the correct amount of waste generated so that it can be reduced. Quarterly, the INEL Pollution Prevention (P2) Unit compares the projected amount of waste generated per process with the actual amount generated. Examples of waste streams that would be addresses for our facility would include be are not limited to: Maintenance, Upgrades, Office and Scrap Metal. There are three potential sources of this variance: inaccurate identification of those who generate the waste; inaccurate identification of the process that generates the waste; and inaccurate measurement of the actual amount generated. The Materials Monitoring Program was proposed to identify the sources of variance and reduce the variance to an acceptable level. Prior to the implementation of the Material Monitoring Program, all information that was gathered and recorded was done so through an informal estimation of waste generated by various personnel concerned with each processes. Due to the inaccuracy of the prior information gathering system, the Material Monitoring Program was established. The heart of this program consists of two main parts. In the first part potential waste generators provide information on projected waste generation process. In the second part, Maintenance, Office, Scrap Metal and Facility Upgrade wastes from given processes is disposed within the appropriate bin dedicated to that process. The Material Monitoring Program allows for the more accurate gathering of information on the various waste types that are being generated quarterly

  5. Thermoelectric Materials

    Science.gov (United States)

    Gao, Peng; Berkun, Isil; Schmidt, Robert D.; Luzenski, Matthew F.; Lu, Xu; Bordon Sarac, Patricia; Case, Eldon D.; Hogan, Timothy P.

    2014-06-01

    Mg2(Si,Sn) compounds are promising candidate low-cost, lightweight, nontoxic thermoelectric materials made from abundant elements and are suited for power generation applications in the intermediate temperature range of 600 K to 800 K. Knowledge on the transport and mechanical properties of Mg2(Si,Sn) compounds is essential to the design of Mg2(Si,Sn)-based thermoelectric devices. In this work, such materials were synthesized using the molten-salt sealing method and were powder processed, followed by pulsed electric sintering densification. A set of Mg2.08Si0.4- x Sn0.6Sb x (0 ≤ x ≤ 0.072) compounds were investigated, and a peak ZT of 1.50 was obtained at 716 K in Mg2.08Si0.364Sn0.6Sb0.036. The high ZT is attributed to a high electrical conductivity in these samples, possibly caused by a magnesium deficiency in the final product. The mechanical response of the material to stresses is a function of the elastic moduli. The temperature-dependent Young's modulus, shear modulus, bulk modulus, Poisson's ratio, acoustic wave speeds, and acoustic Debye temperature of the undoped Mg2(Si,Sn) compounds were measured using resonant ultrasound spectroscopy from 295 K to 603 K. In addition, the hardness and fracture toughness were measured at room temperature.

  6. FOREWORD: Materials metrology Materials metrology

    Science.gov (United States)

    Bennett, Seton; Valdés, Joaquin

    2010-04-01

    It seems that so much of modern life is defined by the materials we use. From aircraft to architecture, from cars to communications, from microelectronics to medicine, the development of new materials and the innovative application of existing ones have underpinned the technological advances that have transformed the way we live, work and play. Recognizing the need for a sound technical basis for drafting codes of practice and specifications for advanced materials, the governments of countries of the Economic Summit (G7) and the European Commission signed a Memorandum of Understanding in 1982 to establish the Versailles Project on Advanced Materials and Standards (VAMAS). This project supports international trade by enabling scientific collaboration as a precursor to the drafting of standards. The VAMAS participants recognized the importance of agreeing a reliable, universally accepted basis for the traceability of the measurements on which standards depend for their preparation and implementation. Seeing the need to involve the wider metrology community, VAMAS approached the Comité International des Poids et Mesures (CIPM). Following discussions with NMI Directors and a workshop at the BIPM in February 2005, the CIPM decided to establish an ad hoc Working Group on the metrology applicable to the measurement of material properties. The Working Group presented its conclusions to the CIPM in October 2007 and published its final report in 2008, leading to the signature of a Memorandum of Understanding between VAMAS and the BIPM. This MoU recognizes the work that is already going on in VAMAS as well as in the Consultative Committees of the CIPM and establishes a framework for an ongoing dialogue on issues of materials metrology. The question of what is meant by traceability in the metrology of the properties of materials is particularly vexed when the measurement results depend on a specified procedure. In these cases, confidence in results requires not only traceable

  7. Alloy materials

    Energy Technology Data Exchange (ETDEWEB)

    Hans Thieme, Cornelis Leo (Westborough, MA); Thompson, Elliott D. (Coventry, RI); Fritzemeier, Leslie G. (Acton, MA); Cameron, Robert D. (Franklin, MA); Siegal, Edward J. (Malden, MA)

    2002-01-01

    An alloy that contains at least two metals and can be used as a substrate for a superconductor is disclosed. The alloy can contain an oxide former. The alloy can have a biaxial or cube texture. The substrate can be used in a multilayer superconductor, which can further include one or more buffer layers disposed between the substrate and the superconductor material. The alloys can be made a by process that involves first rolling the alloy then annealing the alloy. A relatively large volume percentage of the alloy can be formed of grains having a biaxial or cube texture.

  8. Casting materials

    Science.gov (United States)

    Chaudhry, Anil R [Xenia, OH; Dzugan, Robert [Cincinnati, OH; Harrington, Richard M [Cincinnati, OH; Neece, Faurice D [Lyndurst, OH; Singh, Nipendra P [Pepper Pike, OH

    2011-06-14

    A foam material comprises a liquid polymer and a liquid isocyanate which is mixed to make a solution that is poured, injected or otherwise deposited into a corresponding mold. A reaction from the mixture of the liquid polymer and liquid isocyanate inside the mold forms a thermally collapsible foam structure having a shape that corresponds to the inside surface configuration of the mold and a skin that is continuous and unbroken. Once the reaction is complete, the foam pattern is removed from the mold and may be used as a pattern in any number of conventional casting processes.

  9. Energy materials

    CERN Document Server

    Bruce, Duncan W; Walton, Richard I

    2011-01-01

    In an age of global industrialisation and population growth, the area of energy is one that is very much in the public consciousness. Fundamental scientific research is recognised as being crucial to delivering solutions to these issues, particularly to yield novel means of providing efficient, ideally recyclable, ways of converting, transporting and delivering energy. This volume considers a selection of the state-of-the-art materials that are being designed to meet some of the energy challenges we face today. Topics are carefully chosen that show how the skill of the synthetic chemist can

  10. Construction material

    Science.gov (United States)

    Wagh, Arun S [Orland Park, IL; Antink, Allison L [Bolingbrook, IL

    2008-07-22

    A structural material of a polystyrene base and the reaction product of the polystyrene base and a solid phosphate ceramic is applied as a slurry which includes one or more of a metal oxide or a metal hydroxide with a source of phosphate to produce a phosphate ceramic and a poly (acrylic acid or acrylate) or combinations or salts thereof and polystyrene or MgO applied to the polystyrene base and allowed to cure so that the dried aqueous slurry chemically bonds to the polystyrene base. A method is also disclosed of applying the slurry to the polystyrene base.

  11. Potential conflicts connected with the recovery of secondary materials from post mining waste dump

    Directory of Open Access Journals (Sweden)

    Gawor Łukasz

    2017-12-01

    Full Text Available Coal mine spoil dumping grounds are present in the landscape of every mining region. Although the composition of waste material is in general safe for the environment (sedimentary rocks – sandstones, mudstones and siltstones, there may be up to 10% of coal particles in disposed wastes. The presence of organic material causes self-ignition processes and fire hazards. There is a need and the possibility of the recovery of coal, and which should be conducted according to legal regulations and environmental protection rules. The recovery should also be preceded by a feasibility study, a drilling campaign, laboratory tests and requires different environmental permissions. Recovery processes are connected with the work of a preparation plant, which is usually linked with protests from the local community and potential conflicts. This article presents the most significant hazards to the environment, health and human life connected with the functions associated with the installation of the recovery processes of coal from waste material deposited on the dumps. The methods of reducing these threats are described with regards to legal regulations, particularly law deeds concerning the safe recovery processes and further reclamation and restoration of degraded post-mining dumping grounds. The role and participation of interested community members at the preparation for investment stage as well as the period of realization of the preparation processes is described. The question of re-using and managing the post-mining dumping grounds after completion of the recovery processes is discussed.

  12. Photographic materials

    International Nuclear Information System (INIS)

    Jamieson, P.B.

    1980-01-01

    Radiographic films based on silver halides are normally handled under red or orange safelights to prevent fogging due to their sensitivity to white light. The present invention relates to ultraviolet radiation sensitive material which can be handled under virtually white light without significant fogging. The film material is comprised of a base having at least one layer of a photographic silver halide emulsion and a yellow filter dye screening the emulsion from visible radiation. The silver halide emulsion contains 50-100 mole % of silver chloride, the higher the silver chloride content, the lower the visible light sensitivity. The nature and properties of the yellow filter dye are described. When recording an X-ray image, the film is loaded into the camera under white safelight conditions from which light of wavelength shorter than 400 nm is excluded. The film is in contact with one or more phosphor screens capable when struck by X-rays of emitting ultraviolet radiation, the screens having a peak ultraviolet emission within the wavelength range of 250-380 nm. After X-ray exposure, the film is removed and developed. Two examples illustrating the invention are given. (U.K.)

  13. Coating materials

    International Nuclear Information System (INIS)

    Ozeki, Takao; Kimura, Tadashi; Kobayashi, Juichi; Maeda, Yutaka; Nakamoto, Hideo.

    1969-01-01

    A non-solvent type coating material composition having properties as good as thermosetting acrylic or amino alkid resins is provided by employing active energy irradiation, particularly electron beams, using a radically polymerizable low molecular compound (A) (hereafter called an oligomer) containing at least two vinyl radicals in one molecule. This oligomer is produced by reacting an epoxy-containing vinyl monomer with alpha-, beta-ethylene unsaturated carboxylic acids or their anhydrides. The composition (I) contains 10% - 100% of this oligomer. In embodiments, an oligomer having a fiberous trivinyl construction is produced by reacting 180 parts by weight of glycidyl methacrylate ester with 130 parts of itaconic acid in the presence of a polymerization-inhibitor and an addition reaction catalyst at 90 0 C for 6 hours. In practice, the coating material compositions (1), consist of the whole oligomer [I-1]; (2), consist of 10-90% of (A) component and 90%-10% of vinyl monomers containing at least 30% (meth) acrylic monomer [I-2]; (3), 10%-90% of component (A) and 90%-10% of other monomers containing at least two vinyl radicals [I-3]; (4), a mixture of (I-2) and (I-3), [I-4]; and (5), consist of 50% or less unsaturated polyester of 500-5,000 molecular weight range or drying oil, or alkyd resin of 500-5,000 molecular weight range modified by drying oil, [I-5]. As a catalyst a tertiary amino vinyl compound is preferred. Five examples are given. (Iwakiri, K.)

  14. Functional materials

    International Nuclear Information System (INIS)

    Park, J. Y.; Hong, G. W.; Lee, H. J.

    2002-05-01

    Development of fabrication process of functional ceramic materials, evaluation of characteristics and experiments for understanding of irradiation behavior of ceramics were carried out for application of ceramics to the nuclear industry. The developed processes were the SiC surface coating technology with large area for improvement of wear resistance and corrosion resistance, the fabrication technology of SiC composites for excellent irradiation resistance, performance improvement technology of SiC fiber and nano-sized powder processing by combustion ignition and spray. Typical results were CVD SiC coating with diameter of 25cm and thickness of 100μm, highly dense SiC composite by F-CVI, heat-treating technology of SiC fiber using B4C power, and nano-sized powders of ODS-Cu, Li-based breeding materials, Ni-based metal powders with primary particle diameter of 20∼50nm. Furthermore, test equipment, data productions and damage evaluations were performed to understand corrosion resistance and wear resistance of alumina, silicon carbide and silicon nitride under PWR or PHWR operation conditions. Experimental procedures and basic technologies for evaluation of irradiation behavior were also established. Additionally, highly reactive precursor powders were developed by various technologies and the powders were applied to the fabrication of 100 m long Ag/Bi-2223 multi-filamentary wires. High Tc magnets and fly wheel for energy storage were developed, as well

  15. Virtual materiality

    DEFF Research Database (Denmark)

    Søndergaard, Dorte Marie

    as their recounts of them and 3. the consumption of other media products like movies, reality shows, YouTube videos etc. How do we theorize ‘matter’ in such dimensions? Is it possible to theorize virtual matter as ‘materiality’ in line with any real life materiality? What conceptualization will help us understand......? These questions become crucial when we follow matter in and across real life, virtual experience, recounted imagery, night dreams, YouTube videos and even further. Some may already have recognized Phillip’s skeleton army as a transport/transformation from Lord of the Rings, DVD 3, the army which Aragon calls out....... Butler, J. (1993) Bodies that Matter. On the Discursive Limits of “Sex”. London: Routledge. Durkin, K. et al. (1998) Children, Media and Agression. Current Research in Australia and New Zealand. In: Carlson, U. & von Feilitzen, C. (red): Children and Media Violence. Yearbook from the UNESCO International...

  16. Photographic materials

    International Nuclear Information System (INIS)

    1980-01-01

    Radiographic films based on silver halides are normally handled under red or orange safelights to prevent fogging due to their sensitivity to white light. The present invention relates to ultraviolet radiation sensitive material which can be handled under virtually white light without significant fogging. A photographic, chemically sensitised silver halide emulsion is described, containing 50-100 mole % of silver chloride, the higher the silver chloride content, the lower the visible light sensitivity. The remaining silver halide, if any, is silver bromide and/or silver iodide. The silver halide grains are grown in the presence of ammonia, an excess of chloride ions and tetraazaindene growth controller. Examples illustrating the invention are given. (U.K.)

  17. Photovoltaic Materials

    Energy Technology Data Exchange (ETDEWEB)

    Duty, C.; Angelini, J.; Armstrong, B.; Bennett, C.; Evans, B.; Jellison, G. E.; Joshi, P.; List, F.; Paranthaman, P.; Parish, C.; Wereszczak, A.

    2012-10-15

    The goal of the current project was to help make the US solar industry a world leader in the manufacture of thin film photovoltaics. The overall approach was to leverage ORNL’s unique characterization and processing technologies to gain a better understanding of the fundamental challenges for solar cell processing and apply that knowledge to targeted projects with industry members. ORNL has the capabilities in place and the expertise required to understand how basic material properties including defects, impurities, and grain boundaries affect the solar cell performance. ORNL also has unique processing capabilities to optimize the manufacturing process for fabrication of high efficiency and low cost solar cells. ORNL recently established the Center for Advanced Thin-film Systems (CATS), which contains a suite of optical and electrical characterization equipment specifically focused on solar cell research. Under this project, ORNL made these facilities available to industrial partners who were interested in pursuing collaborative research toward the improvement of their product or manufacturing process. Four specific projects were pursued with industrial partners: Global Solar Energy is a solar industry leader in full scale production manufacturing highly-efficient Copper Indium Gallium diSelenide (CIGS) thin film solar material, cells and products. ORNL worked with GSE to develop a scalable, non-vacuum, solution technique to deposit amorphous or nanocrystalline conducting barrier layers on untextured stainless steel substrates for fabricating high efficiency flexible CIGS PV. Ferro Corporation’s Electronic, Color and Glass Materials (“ECGM”) business unit is currently the world’s largest supplier of metallic contact materials in the crystalline solar cell marketplace. Ferro’s ECGM business unit has been the world's leading supplier of thick film metal pastes to the crystalline silicon PV industry for more than 30 years, and has had operational

  18. Rehabilitation materials from surface- coal mines in western U.S.A. III. Relations between elements in mine soil and uptake by plants.

    Science.gov (United States)

    Severson, R.C.; Gough, L.P.

    1984-01-01

    Plant uptake of Cd, Co, Cu, Fe, Mn, Ni, Pb and Zn from mine soils was assessed using alfalfa Medicago sativa, sainfoin Onobrychis viciaefolia, smooth brome Bromus inermis, crested wheatgrass Agropyron cristatum, slender wheatgrass A. trachycaulum and intermediate wheatgrass A. intermedium; mine soil (cover-soil and spoil material) samples were collected from rehabilitated areas of 11 western US surface-coal mines in North Dakota, Montana, Wyoming and Colorado. Correlations between metals in plants and DTPA-extractable metals from mine soils were generally not statistically significant and showed no consistent patterns for a single metal or for a single plant species. Metal uptake by plants, relative to amounts in DTPA extracts of mine soil, was positively related to mine soil organic matter content or negatively related to mine soil pH. DTPA-extractable metal levels were significantly correlated with mine soil pH and organic-matter content.-from Authors

  19. HAZARDOUS MATERIALS IN AQUATIC ENVIRONMENTS OF THE MISSISSIPPI RIVER BASIN

    Energy Technology Data Exchange (ETDEWEB)

    John A. McLachlan

    2003-12-01

    In December 1992, the CBR was awarded a five-year grant of $25M from the US Department of Energy Office of Environmental Management (DOE-EM) to study pollution in the Mississippi River system. The ''Hazardous Materials in Aquatic Environments of the Mississippi River Basin'' project was an interdisciplinary, collaborative research and education project aimed at elucidating the nature and magnitude of toxic materials that contaminate aquatic environments. This project funded 15 collaborative cluster multi-year projects and 41 one-year initiation projects out of 165 submitted research proposals. This project was carried out by 134 research and technical support faculty from Xavier University (School of Arts and Sciences, and College of Pharmacy) and Tulane University (Schools of Liberal Arts and Sciences, Engineering, Medicine, and Public Health and Tropical Medicine), and 173 publications and 140 presentations were produced. More than 100 graduate and undergraduate students were trained through these collaborative cluster and initiation research projects. Nineteen Tulane graduate students received partial funding to conduct their own competitively-chosen research projects, and 28 Xavier undergraduate LIFE Scholars and 30 LIFE Interns were supported with DOE funding to conduct their mentored research projects. Studies in this project have defined: (1) the complex interactions that occur during the transport of contaminants, (2) the actual and potential impact on ecological systems and health, and (3) the mechanisms through which these impacts might be remediated. The bayou and spoil banks of Bayou Trepagnier were mapped and analyzed in terms of risks associated with the levels of hydrocarbons and metals at specific sample sites. Data from contaminated sample sites have been incorporated into a large database and used in GIS analyses to track the fate and transport of heavy metals from spoil banks into the surrounding marsh. These data are crucial

  20. Survival of Spoilage and Pathogenic Microorganisms on Cardboard and Plastic Packaging Materials

    Directory of Open Access Journals (Sweden)

    Lorenzo Siroli

    2017-12-01

    Full Text Available The aim of this work was to study the interaction of corrugated and plastic materials with pathogenic and spoiling microorganisms frequently associated to fresh produce. The effect of the two packaging materials on the survival during the storage of microorganisms belonging to the species Escherichia coli, Listeria monocytogenes, Salmonella enteritidis, Saccharomyces cerevisiae, Lactobacillus plantarum, Pseudomonas fluorescens, and Aspergillus flavus was studied through traditional plate counting and scanning electron microscopy (SEM. The results obtained showed that cardboard materials, if correctly stored, reduced the potential of packaging to cross-contaminate food due to a faster viability loss by spoilage and pathogenic microorganisms compared to the plastic ones. In fact, the cell loads of the pathogenic species considered decreased over time independently on the inoculation level and packaging material used. However, the superficial viability losses were significantly faster in cardboard compared to plastic materials. The same behavior was observed for the spoilage microorganisms considered. The SEM microphotographs indicate that the reduction of superficial contamination on cardboard surfaces was due to the entrapping of the microbial cells within the fibers and the pores of this material. In addition, SEM data showed that the entrapped cells were subjected to more or less rapid lyses, depending on the species, due to the absence of water and nutrients, with the exception of molds. The latter spoilers were able to proliferate inside the cardboard fibers only when the absorption of water was not prevented during the storage. In conclusion, the findings of this work showed the reduction of cross-contamination potential of corrugated compared to plastic packaging materials used in fruit and vegetable sector. However, the findings outlined the importance of hygiene and low humidity during cardboard storage to prevent the mold growth on

  1. Biointegrating Materials

    Science.gov (United States)

    Amédée, J.; Bordenave, L.; Durrieu, M.-C.; Fricain, J.-C.; Pothuaud, L.

    The extraordinary increase in human longevity explains the growing need for replacement organs. The remarkable successes of conventional transplants (associated with the development of effective antirejection drugs and improved control of their administration) are also accompanied by certain drawbacks. First on the list is an inadequate supply of replacement organs: the number of candidates for transplants grows larger, opposition to the removal of organs increases, and the number of transplants has reached a ceiling. Furthermore, it has come to light over the past few years that organ transplants carry a significant risk of transmitting pathogens. Finally, the main drawback lies in the need to pursue an immunosuppression treatment. Scientists and doctors have long been in search of alternatives to human organ transplants. According to the definition drawn up in Chester in 1986 at the Consensus Conference organised under the aegis of the European Society for Biomaterials, biomaterials are non-viable materials used in a medical device and destined to interact with biological systems, whether they contribute to the constitution of a diagnostic device, a tissue or organ substitute, or a device designed to provide functional assistance or replacement.

  2. Coating materials

    International Nuclear Information System (INIS)

    Ozeki, Takao; Kimura, Tadashi; Kobayashi, Juichi; Maeda, Yutaka; Nakamoto, Hideo.

    1969-01-01

    A non-solvent type coating material composition is provided which can be hardened by irradiation with active energy, particularly electron beams, using a composition which contains 10%-100% of a radically polymerizable low molecular compound (A), (hereafter called an oligomer), having at least two vinyl radicals in one molecule. These compositions have a high degree of polymerization and characteristics equivalent to thermosetting acrylic or amino alkyd resin. The oligomer (A) is produced by reacting an epoxy-containing vinyl monomer with saturated polycarboxylic acids or anhydrides. In one embodiment, 146 parts by weight of adipic acid and 280 parts of glycidyl methacrylate ester undergo addition reaction in the presence of a polymerization-inhibitor and a catalyst at 90 0 C for 6 hours to produce an oligomer having a fiberous divinyl construction. The coating composition utilizes this oligomer in the forms of (I-1), a whole oligomer; (I-2), 0%-90% of this oligomer and 90%-10% of a vinyl monomer containing at least 30% of (meth) acrylic monomer; (I-3), 10%-90% of such oligomer and 90%-10% of other monomers containing at least two vinyl radicals in one molecule; (I-4), a mixture of (I-2) and (I-3) in proportion of 1/9 to 9/1, and (I-5), above four compositions each containing 50% or less unsaturated polyester or drying oil having 500-5,000 molecules or a drying oil-modified alkyd resin having 500-5,000 molecules. Four examples are given. (Iwakiri, K.)

  3. Environmental impact and recovery at two dumping sites for dredged material in the North Sea

    International Nuclear Information System (INIS)

    Stronkhorst, J.; Ariese, F.; Hattum, B. van; Postma, J.F.; Kluijver, M. de; Besten, P.J. den; Bergman, M.J.N.; Daan, R.; Murk, A.J.; Vethaak, A.D.

    2003-01-01

    Marine benthic resources near dumping sites are adversely affected by physical disturbances, but a causal link to contaminant damage could not be found. - The environmental impact and recovery associated with the long and uninterrupted disposal of large volumes of moderately contaminated dredged material from the port of Rotterdam was studied at nearby dumping sites in the North Sea. Observations were made on sediment contamination, ecotoxicity, biomarker responses and benthic community changes shortly after dumping at the 'North' site had ceased and at the start of disposal at the new dumping site 'Northwest'. During the period of dumping, very few benthic invertebrates were found at the North site. Concentrations of cadmium, mercury, polychlorinated biphenyls (PCBs), polyaromatic hydrocarbons (PAHs) and tributyltin (TBT) in the fine sediment fraction ( 3 of moderately contaminated dredged material had been dumped at the new dumping site Northwest, the species richness and abundance of benthic invertebrates declined over an area extending about 1-2 km eastwards. This correlated with a shift in sediment texture from sand to silt. The contamination of the fine sediment fraction at the Northwest location doubled. It is concluded that marine benthic resources at and around the dumping sites have been adversely affected by physical disturbance (burial, smothering). However, no causal link could be established with sediment-associated contaminants from the dredged spoils

  4. The Newest Machine Material

    International Nuclear Information System (INIS)

    Seo, Yeong Seop; Choe, Byeong Do; Bang, Meong Sung

    2005-08-01

    This book gives descriptions of machine material with classification of machine material and selection of machine material, structure and connection of material, coagulation of metal and crystal structure, equilibrium diagram, properties of metal material, elasticity and plasticity, biopsy of metal, material test and nondestructive test. It also explains steel material such as heat treatment of steel, cast iron and cast steel, nonferrous metal materials, non metallic materials, and new materials.

  5. Geopolymer resin materials, geopolymer materials, and materials produced thereby

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Dong-Kyun; Medpelli, Dinesh; Ladd, Danielle; Mesgar, Milad

    2018-01-09

    A product formed from a first material including a geopolymer resin material, a geopolymer material, or a combination thereof by contacting the first material with a fluid and removing at least some of the fluid to yield a product. The first material may be formed by heating and/or aging an initial geopolymer resin material to yield the first material before contacting the first material with the fluid. In some cases, contacting the first material with the fluid breaks up or disintegrates the first material (e.g., in response to contact with the fluid and in the absence of external mechanical stress), thereby forming particles having an external dimension in a range between 1 nm and 2 cm.

  6. Gas storage materials, including hydrogen storage materials

    Science.gov (United States)

    Mohtadi, Rana F; Wicks, George G; Heung, Leung K; Nakamura, Kenji

    2013-02-19

    A material for the storage and release of gases comprises a plurality of hollow elements, each hollow element comprising a porous wall enclosing an interior cavity, the interior cavity including structures of a solid-state storage material. In particular examples, the storage material is a hydrogen storage material such as a solid state hydride. An improved method for forming such materials includes the solution diffusion of a storage material solution through a porous wall of a hollow element into an interior cavity.

  7. Geopolymer resin materials, geopolymer materials, and materials produced thereby

    Science.gov (United States)

    Seo, Dong-Kyun; Medpelli, Dinesh; Ladd, Danielle; Mesgar, Milad

    2016-03-29

    A product formed from a first material including a geopolymer resin material, a geopolymer resin, or a combination thereof by contacting the first material with a fluid and removing at least some of the fluid to yield a product. The first material may be formed by heating and/or aging an initial geopolymer resin material to yield the first material before contacting the first material with the fluid. In some cases, contacting the first material with the fluid breaks up or disintegrates the first material (e.g., in response to contact with the fluid and in the absence of external mechanical stress), thereby forming particles having an external dimension in a range between 1 nm and 2 cm.

  8. Towards Materials Sustainability through Materials Stewardship

    Directory of Open Access Journals (Sweden)

    Christopher D. Taylor

    2016-10-01

    Full Text Available Materials sustainability requires a concerted change in philosophy across the entire materials lifecycle, orienting around the theme of materials stewardship. In this paper, we address the opportunities for improved materials conservation through dematerialization, durability, design for second life, and diversion of waste streams through industrial symbiosis.

  9. Computational Materials Science | Materials Science | NREL

    Science.gov (United States)

    Computational Materials Science Computational Materials Science An image of interconnecting, sphere science capabilities span many research fields and interests. Electronic, Optical, and Transport Properties of Photovoltaic Materials Material properties and defect physics of Si, CdTe, III-V, CIGS, CZTS

  10. The materials physics companion

    CERN Document Server

    Fischer-Cripps, Anthony C

    2014-01-01

    Introduction to Materials Physics: Structure of matter. Solid state physics. Dynamic properties of solids. Dielectric Properties of Materials: Dielectric properties. Ferroelectric and piezoelectric materials. Dielectric breakdown. Applications of dielectrics. Magnetic Properties of Materials: Magnetic properties. Magnetic moment. Spontaneous magnetization. Superconductivity.

  11. Metallic composite materials

    International Nuclear Information System (INIS)

    Frommeyer, G.

    1987-01-01

    The structure and properties of metallic composite materials and composite materials with metallic matrix are considered. In agreement with the morphology of constituent phases the following types of composite materials are described: dispersion-strengthened composite materials; particle-reinforced composite materials; fibrous composite materials; laminar composite materials. Data on strength and electric properties of the above-mentioned materials, as well as effect of the amount, location and geometric shape of the second phase on them, are presented

  12. Composite material dosimeters

    Science.gov (United States)

    Miller, Steven D.

    1996-01-01

    The present invention is a composite material containing a mix of dosimeter material powder and a polymer powder wherein the polymer is transparent to the photon emission of the dosimeter material powder. By mixing dosimeter material powder with polymer powder, less dosimeter material is needed compared to a monolithic dosimeter material chip. Interrogation is done with excitation by visible light.

  13. Method for forming materials

    Science.gov (United States)

    Tolle, Charles R [Idaho Falls, ID; Clark, Denis E [Idaho Falls, ID; Smartt, Herschel B [Idaho Falls, ID; Miller, Karen S [Idaho Falls, ID

    2009-10-06

    A material-forming tool and a method for forming a material are described including a shank portion; a shoulder portion that releasably engages the shank portion; a pin that releasably engages the shoulder portion, wherein the pin defines a passageway; and a source of a material coupled in material flowing relation relative to the pin and wherein the material-forming tool is utilized in methodology that includes providing a first material; providing a second material, and placing the second material into contact with the first material; and locally plastically deforming the first material with the material-forming tool so as mix the first material and second material together to form a resulting material having characteristics different from the respective first and second materials.

  14. Photorefractive Materials and Their Applications 2 Materials

    CERN Document Server

    Günter, Peter

    2007-01-01

    Photorefractive Materials and Their Applications 2: Materials is the second of three volumes within the Springer Series in Optical Sciences. The book gives a comprehensive review of the most important photorefractive materials and discusses the physical properties of organic and inorganic crystals as well as poled polymers. In this volume, photorefractive effects have been investigated at wavelengths covering the UV, visible and near infrared. Researchers in the field and graduate students of solid-state physics and engineering will gain a thorough understanding of the properties of materials in photorefractive applications. The other two volumes are: Photorefractive Materials and Their Applications 1: Basic Effects. Photorefractive Materials and Their Applications 3: Applications.

  15. Mechanical Material Engineering

    International Nuclear Information System (INIS)

    Kim, Mun Il

    1993-01-01

    This book introduced mechanical material with introduction, basic problems about metal ingredient of machine of metal and alloy, property of metal material mechanical metal material such as categorization of metal material and high tensile structure steel, mechanic design and steel material with three important points on using of steel materials, selection and directions machine structural steel, selection and directions of steel for tool, selection and instruction of special steel like stainless steel and spring steel, nonferrous metal materials and plastic.

  16. Materials with structural hierarchy

    Science.gov (United States)

    Lakes, Roderic

    1993-01-01

    The role of structural hierarchy in determining bulk material properties is examined. Dense hierarchical materials are discussed, including composites and polycrystals, polymers, and biological materials. Hierarchical cellular materials are considered, including cellular solids and the prediction of strength and stiffness in hierarchical cellular materials.

  17. Coated electroactive materials

    Science.gov (United States)

    Amine, Khalil; Abouimrane, Ali

    2016-08-30

    A process includes suspending an electroactive material in a solvent, suspending or dissolving a carbon precursor in the solvent; and depositing the carbon precursor on the electroactive material to form a carbon-coated electroactive material. Compositions include a graphene-coated electroactive material prepared from a solution phase mixture or suspension of an electroactive material and graphene, graphene oxide, or a mixture thereof.

  18. Aerogel / Polymer Composite Materials

    Science.gov (United States)

    Williams, Martha K. (Inventor); Smith, Trent M. (Inventor); Fesmire, James E. (Inventor); Roberson, Luke B. (Inventor); Clayton, LaNetra M. (Inventor)

    2017-01-01

    The invention provides new composite materials containing aerogels blended with thermoplastic polymer materials at a weight ratio of aerogel to thermoplastic polymer of less than 20:100. The composite materials have improved thermal insulation ability. The composite materials also have better flexibility and less brittleness at low temperatures than the parent thermoplastic polymer materials.

  19. Nanocrystalline ceramic materials

    Science.gov (United States)

    Siegel, Richard W.; Nieman, G. William; Weertman, Julia R.

    1994-01-01

    A method for preparing a treated nanocrystalline metallic material. The method of preparation includes providing a starting nanocrystalline metallic material with a grain size less than about 35 nm, compacting the starting nanocrystalline metallic material in an inert atmosphere and annealing the compacted metallic material at a temperature less than about one-half the melting point of the metallic material.

  20. Materials Informatics: Statistical Modeling in Material Science.

    Science.gov (United States)

    Yosipof, Abraham; Shimanovich, Klimentiy; Senderowitz, Hanoch

    2016-12-01

    Material informatics is engaged with the application of informatic principles to materials science in order to assist in the discovery and development of new materials. Central to the field is the application of data mining techniques and in particular machine learning approaches, often referred to as Quantitative Structure Activity Relationship (QSAR) modeling, to derive predictive models for a variety of materials-related "activities". Such models can accelerate the development of new materials with favorable properties and provide insight into the factors governing these properties. Here we provide a comparison between medicinal chemistry/drug design and materials-related QSAR modeling and highlight the importance of developing new, materials-specific descriptors. We survey some of the most recent QSAR models developed in materials science with focus on energetic materials and on solar cells. Finally we present new examples of material-informatic analyses of solar cells libraries produced from metal oxides using combinatorial material synthesis. Different analyses lead to interesting physical insights as well as to the design of new cells with potentially improved photovoltaic parameters. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Material efficiency: providing material services with less material production.

    Science.gov (United States)

    Allwood, Julian M; Ashby, Michael F; Gutowski, Timothy G; Worrell, Ernst

    2013-03-13

    Material efficiency, as discussed in this Meeting Issue, entails the pursuit of the technical strategies, business models, consumer preferences and policy instruments that would lead to a substantial reduction in the production of high-volume energy-intensive materials required to deliver human well-being. This paper, which introduces a Discussion Meeting Issue on the topic of material efficiency, aims to give an overview of current thinking on the topic, spanning environmental, engineering, economics, sociology and policy issues. The motivations for material efficiency include reducing energy demand, reducing the emissions and other environmental impacts of industry, and increasing national resource security. There are many technical strategies that might bring it about, and these could mainly be implemented today if preferred by customers or producers. However, current economic structures favour the substitution of material for labour, and consumer preferences for material consumption appear to continue even beyond the point at which increased consumption provides any increase in well-being. Therefore, policy will be required to stimulate material efficiency. A theoretically ideal policy measure, such as a carbon price, would internalize the externality of emissions associated with material production, and thus motivate change directly. However, implementation of such a measure has proved elusive, and instead the adjustment of existing government purchasing policies or existing regulations-- for instance to do with building design, planning or vehicle standards--is likely to have a more immediate effect.

  2. Conducting Polymeric Materials

    DEFF Research Database (Denmark)

    Hvilsted, Søren

    2016-01-01

    The overall objective of this collection is to provide the most recent developments within the various areas of conducting polymeric materials. The conductivity of polymeric materials is caused by electrically charged particles, ions, protons and electrons. Materials in which electrons...

  3. Multifunctional materials and composites

    Science.gov (United States)

    Seo, Dong-Kyun; Jeon, Ki-Wan

    2017-08-22

    Forming multifunctional materials and composites thereof includes contacting a first material having a plurality of oxygen-containing functional groups with a chalcogenide compound, and initiating a chemical reaction between the first material and the chalcogenide compound, thereby replacing oxygen in some of the oxygen-containing functional groups with chalcogen from the chalcogen-containing compound to yield a second material having chalcogen-containing functional groups and oxygen-containing functional groups. The first material is a carbonaceous material or a macromolecular material. A product including the second material is collected and may be processed further to yield a modified product or a composite.

  4. Sea materials experimental plans

    International Nuclear Information System (INIS)

    1987-07-01

    This Seal Materials Performance Test Plan describes the plan for testing materials that will be used to seal a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. The need for sealing and backfilling the repository and the use of various sealing materials are described. The seal materials include mined salt backfills, cementitious bulkheads and plugs, and earthen backfills. The laboratory testing program for characterizing the behavior and performance of these materials is described. This report includes plans for screening materials, evaluating candidate materials to be tested, and testing a representative set of materials

  5. Nanoscale materials in chemistry

    National Research Council Canada - National Science Library

    Klabunde, Kenneth J; Richards, Ryan

    2009-01-01

    ...: Disordered, Porous Nanostructures Stephanie L. Brock 209 9 Ordered Microporous and Mesoporous Materials Freddy Kleitz 243 10 Applications of Microporous and Mesoporous Materials Anirban Ghosh,...

  6. Physically Functional Materials

    DEFF Research Database (Denmark)

    2002-01-01

    acids or peptides having azobenzenes or other physicially functional groups, e.g., photoresponsive groups, as side chains. These compounds may be synthesized using solid phase peptide synthesis techniques. Materials, e.g., thin films, comprising such compounds may be used for optical storage...... of information (holographic data storage), nonlinear optics (NLO), as photoconductors, photonic band-gap materials, electrically conducting materials, electroluminescent materials, piezo-electric materials, pyroelectric materials, magnetic materials, ferromagnetic materials, ferroelectric materials......, photorefractive materials, or materials in which light-induced conformational changes can be produced. Optical anisotropy may reversibly be generated with polarized laser light whereby a hologram is formed. First order diffraction efficiencies of up to around 80% have been obtained....

  7. Tritium breeding materials

    International Nuclear Information System (INIS)

    Hollenberg, G.W.; Johnson, C.E.; Abdou, M.

    1984-03-01

    Tritium breeding materials are essential to the operation of D-T fusion facilities. Both of the present options - solid ceramic breeding materials and liquid metal materials are reviewed with emphasis not only on their attractive features but also on critical materials issues which must be resolved

  8. Tritium breeding materials

    International Nuclear Information System (INIS)

    Hollenberg, G.W.; Johnson, C.E.; Abdou, M.A.

    1984-01-01

    Tritium breeding materials are essential to the operation of D-T fusion facilities. Both of the present options - solid ceramic breeding materials and liquid metal materials are reviewed with emphasis not only on their attractive features but also on critical materials issues which must be resolved

  9. Materials Science | NREL

    Science.gov (United States)

    microscopy and imaging science, interfacial and surface science, materials discovery, and thin-film material Science Materials Science Illustration with bottom row showing a ball-and-stick model and top row dense black band. State-of-the-art advances in materials science come from a combination of experiments

  10. Coated ceramic breeder materials

    Science.gov (United States)

    Tam, Shiu-Wing; Johnson, Carl E.

    1987-01-01

    A breeder material for use in a breeder blanket of a nuclear reactor is disclosed. The breeder material comprises a core material of lithium containing ceramic particles which has been coated with a neutron multiplier such as Be or BeO, which coating has a higher thermal conductivity than the core material.

  11. Materials Analysis and Modeling of Underfill Materials.

    Energy Technology Data Exchange (ETDEWEB)

    Wyatt, Nicholas B [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Chambers, Robert S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-08-01

    The thermal-mechanical properties of three potential underfill candidate materials for PBGA applications are characterized and reported. Two of the materials are a formulations developed at Sandia for underfill applications while the third is a commercial product that utilizes a snap-cure chemistry to drastically reduce cure time. Viscoelastic models were calibrated and fit using the property data collected for one of the Sandia formulated materials. Along with the thermal-mechanical analyses performed, a series of simple bi-material strip tests were conducted to comparatively analyze the relative effects of cure and thermal shrinkage amongst the materials under consideration. Finally, current knowledge gaps as well as questions arising from the present study are identified and a path forward presented.

  12. Trends in building materials

    CSIR Research Space (South Africa)

    Mapiravana, Joseph

    2012-07-01

    Full Text Available , steel and composites research. Analysis of the building materials market situation in South Africa identified the major building material cost drivers as cement and concrete and steel. For South Africa, research and development focus has been... in South Africa be cement and concrete, light-weight steel construction, smart tiles and composite materials. Nanotechnology materials should be used for property enhancement. The building materials developed should be modularised and/or panelised...

  13. Plasma-material interactions

    International Nuclear Information System (INIS)

    Wilson, K.L.

    1984-01-01

    Plasma-interactive components must be resistant to erosion processes, efficient in heat removal, and effective in minimizing tritium inventory and permeation. As long as plasma edge temperatures are 50 eV, no one material can satisfy the diverse requirements imposed by these plasma materials interactions. The only solution is the design of duplex, or even more complicated, structures. The material that faces the plasma should be low atomic number, with acceptable erosion and evaporation characteristics. The substrate material must have high thermal conductivity for heat removal. Finally, materials must be selected judiciously for tritium compatibility. In conclusion, materials play a critical role in the achievement of safe and economical magnetic fusion energy. Improvements in materials have already led to many advances in present day device operation, but additional innovative materials solutions are required for the critical plasma materials interaction issues in future power reactors

  14. Advancing materials research

    International Nuclear Information System (INIS)

    Langford, H.D.; Psaras, P.A.

    1987-01-01

    The topics discussed in this volume include historical perspectives in the fields of materials research and development, the status of selected scientific and technical areas, and current topics in materials research. Papers are presentd on progress and prospects in metallurgical research, microstructure and mechanical properties of metals, condensed-matter physics and materials research, quasi-periodic crystals, and new and artifically structured electronic and magnetic materials. Consideration is also given to materials research in catalysis, advanced ceramics, organic polymers, new ways of looking at surfaces, and materials synthesis and processing

  15. Advanced energy materials

    CERN Document Server

    Tiwari, Ashutosh

    2014-01-01

    An essential resource for scientists designing new energy materials for the vast landscape of solar energy conversion as well as materials processing and characterization Based on the new and fundamental research on novel energy materials with tailor-made photonic properties, the role of materials engineering has been to provide much needed support in the development of photovoltaic devices. Advanced Energy Materials offers a unique, state-of-the-art look at the new world of novel energy materials science, shedding light on the subject's vast multi-disciplinary approach The book focuses p

  16. Materials science and engineering

    Energy Technology Data Exchange (ETDEWEB)

    Lesuer, D.R.

    1997-02-01

    During FY-96, work within the Materials Science and Engineering Thrust Area was focused on material modeling. Our motivation for this work is to develop the capability to study the structural response of materials as well as material processing. These capabilities have been applied to a broad range of problems, in support of many programs at Lawrence Livermore National Laboratory. These studies are described in (1) Strength and Fracture Toughness of Material Interfaces; (2) Damage Evolution in Fiber Composite Materials; (3) Flashlamp Envelope Optical Properties and Failure Analysis; (4) Synthesis and Processing of Nanocrystalline Hydroxyapatite; and (5) Room Temperature Creep Compliance of Bulk Kel-E.

  17. Materials for breeding blankets

    International Nuclear Information System (INIS)

    Mattas, R.F.; Billone, M.C.

    1995-09-01

    There are several candidate concepts for tritium breeding blankets that make use of a number of special materials. These materials can be classified as Primary Blanket Materials, which have the greatest influence in determining the overall design and performance, and Secondary Blanket Materials, which have key functions in the operation of the blanket but are less important in establishing the overall design and performance. The issues associated with the blanket materials are specified and several examples of materials performance are given. Critical data needs are identified

  18. Materials for breeding blankets

    International Nuclear Information System (INIS)

    Mattas, R.F.; Billone, M.C.

    1996-01-01

    There are several candidate concepts for tritium breeding blankets that make use of a number of special materials. These materials can be classified as primary blanket materials, which have the greatest influence in determining the overall design and performance, and secondary blanket materials, which have key functions in the operation of the blanket but are less important in establishing the overall design and performance. The issues associated with the blanket materials are specified and several examples of materials performance are given. Critical data needs are identified. (orig.)

  19. Materials by design

    International Nuclear Information System (INIS)

    Eberhardt, J.; Hay, P.J.; Carpenter, J.A. Jr.

    1986-01-01

    Major developments in materials characterization instrumentation over the past decade have helped significantly to elucidate complex processes and phenomena connected with the microstructure of materials and interfacial interactions. Equally remarkable advances in theoretical models and computer technology also have been taking place during this period. These latter now permit, for example, in selected cases the computation of material structures and bonding and the prediction of some material properties. Two assessments of the state of the art of instrumental techniques and theoretical methods for the study of material structures and properties have recently been conducted. This paper discusses aspects from these assessments of computational theoretical methods apply to materials

  20. Materials risk analysis.

    Science.gov (United States)

    2010-02-01

    State highway authorities routinely examine the quality of the materials used to build highway construction projects. Some : materials are tested, some are accepted through a manufacturers certification of quality or compliance, some are physicall...

  1. Smart hydrogel functional materials

    CERN Document Server

    Chu, Liang-Yin; Ju, Xiao-Jie

    2014-01-01

    This book systematically introduces smart hydrogel functional materials with the configurations ranging from hydrogels to microgels. It serves as an excellent reference for designing and fabricating artificial smart hydrogel functional materials.

  2. Practical materials characterization

    CERN Document Server

    2014-01-01

    Presents cross-comparison between materials characterization techniquesIncludes clear specifications of strengths and limitations of each technique for specific materials characterization problemFocuses on applications and clear data interpretation without extensive mathematics

  3. Bridged graphite oxide materials

    Science.gov (United States)

    Herrera-Alonso, Margarita (Inventor); McAllister, Michael J. (Inventor); Aksay, Ilhan A. (Inventor); Prud'homme, Robert K. (Inventor)

    2010-01-01

    Bridged graphite oxide material comprising graphite sheets bridged by at least one diamine bridging group. The bridged graphite oxide material may be incorporated in polymer composites or used in adsorption media.

  4. Sustainable Materials Management

    Science.gov (United States)

    To introduce businesses, NGOs, and government officials to the concept of Sustainable Materials Management (SMM). To provide tools to allow stakeholders to take a lifecycle approach managing their materials, & to encourage them to join a SMM challenge.

  5. Injection Laryngoplasty Materials

    OpenAIRE

    Haldun Oðuz

    2013-01-01

    Injection laryngoplasty is one of the treatment options for voice problems. In the recent years, more safe and more biocompatible injection materials are available on the market. Long and short term injection materials are discussed in this review.

  6. Materials Science and Engineering |

    Science.gov (United States)

    Engineering? What Is Materials Science and Engineering? MSE combines engineering, physics and chemistry to solve problems in nanotechnology, biotechnology, information technology, energy, manufacturing, and more ,' which could replace steel. Materials Science and Mechanical Engineering Professors work together to

  7. Molecules to Materials

    Indian Academy of Sciences (India)

    the School of Chemistry, ... Design and fabrication of molecular materials combines ... insights into materials gained through condensed matter ... The most important characteristic of liquid crystals is that they exhibit fluid nature and at the same.

  8. Nanostructured composite reinforced material

    Science.gov (United States)

    Seals, Roland D [Oak Ridge, TN; Ripley, Edward B [Knoxville, TN; Ludtka, Gerard M [Oak Ridge, TN

    2012-07-31

    A family of materials wherein nanostructures and/or nanotubes are incorporated into a multi-component material arrangement, such as a metallic or ceramic alloy or composite/aggregate, producing a new material or metallic/ceramic alloy. The new material has significantly increased strength, up to several thousands of times normal and perhaps substantially more, as well as significantly decreased weight. The new materials may be manufactured into a component where the nanostructure or nanostructure reinforcement is incorporated into the bulk and/or matrix material, or as a coating where the nanostructure or nanostructure reinforcement is incorporated into the coating or surface of a "normal" substrate material. The nanostructures are incorporated into the material structure either randomly or aligned, within grains, or along or across grain boundaries.

  9. Supplements to Textbook Materials.

    Science.gov (United States)

    Holmes, Ken

    1994-01-01

    Describes the many kinds of materials that English teachers can draw upon to enrich and expand students' experiences with literature. Outlines ancillary materials used to supplement the study of William Shakespeare's "Julius Caesar." (HB)

  10. Bulletin of Materials Science

    Indian Academy of Sciences (India)

    Low temperature preparation of some perovskites La2MM'O6 (M,M'=Cr,Mn,Fe ... Inorganic materials for optical data storage -- S K Date ... Dielectric and polarization studies on some organic materials -- B jagannadh and Lalitha Sirdeshmukh.

  11. Erodibility of cemented materials

    CSIR Research Space (South Africa)

    Gass, BG

    1993-03-01

    Full Text Available The use of stabilised layers is cost effective in road construction in South Africa. Some stabilised materials have however been found to be susceptible to erosion. To identify erodible materials the Erosion Test was developed in 1989...

  12. Contact materials for nanoelectronics

    KAUST Repository

    Alshareef, Husam N.; Quevedo-Ló pez, Manuel Angel Quevedo; Majhi, Prashant

    2011-01-01

    In this article, we review current research activities in contact material development for electronic and nanoelectronic devices. A fundamental issue in contact materials research is to understand and control interfacial reactions and phenomena

  13. Materials Genome Initiative

    Science.gov (United States)

    Vickers, John

    2015-01-01

    The Materials Genome Initiative (MGI) project element is a cross-Center effort that is focused on the integration of computational tools to simulate manufacturing processes and materials behavior. These computational simulations will be utilized to gain understanding of processes and materials behavior to accelerate process development and certification to more efficiently integrate new materials in existing NASA projects and to lead to the design of new materials for improved performance. This NASA effort looks to collaborate with efforts at other government agencies and universities working under the national MGI. MGI plans to develop integrated computational/experimental/ processing methodologies for accelerating discovery and insertion of materials to satisfy NASA's unique mission demands. The challenges include validated design tools that incorporate materials properties, processes, and design requirements; and materials process control to rapidly mature emerging manufacturing methods and develop certified manufacturing processes

  14. Analysis of irradiated materials

    International Nuclear Information System (INIS)

    Bellamy, B.A.

    1988-01-01

    Papers presented at the UKAEA Conference on Materials Analysis by Physical Techniques (1987) covered a wide range of techniques as applied to the analysis of irradiated materials. These varied from reactor component materials, materials associated with the Authority's radwaste disposal programme, fission products and products associated with the decommissioning of nuclear reactors. An invited paper giving a very comprehensive review of Laser Ablation Microprobe Mass Spectroscopy (LAMMS) was included in the programme. (author)

  15. Fuels and auxiliary materials

    International Nuclear Information System (INIS)

    Svab, V.

    A brief survey is given of the problems of fuels, fuel cans, absorption and moderator materials proceeding from the papers presented at the 1971 4th Geneva Conference on the Peaceful Uses of Nuclear Energy and the 1970 IAEA Conference in New York. Attention is focused on the behaviour of fuel and fuel can materials for thermal and fast reactors during irradiation, radiation stability of absorption materials and the effects of radiation on concrete and on moderator materials. (Z.M.)

  16. Contributions to materials science

    International Nuclear Information System (INIS)

    Asbeck, O.W.; Matucha, K.H.

    1989-01-01

    The ten papers presented at a festive colloquium held on November 14, 1988 in Frankfurt to honour Prof. Peter Wincierz deal with the texture and mechanical anisotropy of zirconium alloys (by E. Tenckhoff), materials for cladding tubes (H. Boehm), aluminium materials achieved by near technology (W. Bunk), dispersion-strengthened materials (H. Fischmeister), materials for plain bearings (K.H. Matucha), and the archeometallurgy of copper (H.-G. Bachmann). (MM) [de

  17. Modern electronic materials

    CERN Document Server

    Watkins, John B

    2013-01-01

    Modern Electronic Materials focuses on the development of electronic components. The book first discusses the history of electronic components, including early developments up to 1900, developments up to World War II, post-war developments, and a comparison of present microelectric techniques. The text takes a look at resistive materials. Topics include resistor requirements, basic properties, evaporated film resistors, thick film resistors, and special resistors. The text examines dielectric materials. Considerations include basic properties, evaporated dielectric materials, ceramic dielectri

  18. Machinability of advanced materials

    CERN Document Server

    Davim, J Paulo

    2014-01-01

    Machinability of Advanced Materials addresses the level of difficulty involved in machining a material, or multiple materials, with the appropriate tooling and cutting parameters.  A variety of factors determine a material's machinability, including tool life rate, cutting forces and power consumption, surface integrity, limiting rate of metal removal, and chip shape. These topics, among others, and multiple examples comprise this research resource for engineering students, academics, and practitioners.

  19. Materials Genome Initiative Element

    Science.gov (United States)

    Vickers, John

    2015-01-01

    NASA is committed to developing new materials and manufacturing methods that can enable new missions with ever increasing mission demands. Typically, the development and certification of new materials and manufacturing methods in the aerospace industry has required more than 20 years of development time with a costly testing and certification program. To reduce the cost and time to mature these emerging technologies, NASA is developing computational materials tools to improve understanding of the material and guide the certification process.

  20. Advanced energy materials (Preface)

    Science.gov (United States)

    Titus, Elby; Ventura, João; Araújo, João Pedro; Campos Gil, João

    2017-12-01

    Advances in material science make it possible to fabricate the building blocks of an entirely new generation of hierarchical energy materials. Recent developments were focused on functionality and areas connecting macroscopic to atomic and nanoscale properties, where surfaces, defects, interfaces and metastable state of the materials played crucial roles. The idea is to combine both, the top-down and bottom-up approach as well as shape future materials with a blend of both the paradigms.

  1. Computing and Material

    DEFF Research Database (Denmark)

    Ramsgaard Thomsen, Mette; Tamke, Martin

    2013-01-01

    The digital is often said to bring us away from material. The adverse is true: digital design and fabrication grants new interfaces towards material and allows architectural design to engage with material on architectural scale in a way that is further reaching than ever before....

  2. Advances in dental materials.

    Science.gov (United States)

    Fleming, Garry J P

    2014-05-01

    The dental market is replete with new resorative materials marketed on the basis of novel technological advances in materials chemistry, bonding capability or reduced operator time and/or technique sensitivity. This paper aims to consider advances in current materials, with an emphasis on their role in supporting contemporary clinical practice.

  3. Transport of radioactive materials

    International Nuclear Information System (INIS)

    2013-01-01

    This ninth chapter presents de CNEN-NE--5.01 norm 'Transport of radioactive material'; the specifications of the radioactive materials for transport; the tests of the packages; the requests for controlling the transport and the responsibilities during the transport of radioactive material

  4. Materials for Space Exploration

    Science.gov (United States)

    Robertson, Luke B.; Williams, Martha

    2010-01-01

    Topics include a lab overview, testing and processing equipment, hemochromic hydrogen sensors, antimicrobial materials, wire system materials, CNT ink formulations, CNT ink dust screens, CNT ink printed circuitry, cryogenic materials development, fire and polymers, the importance of lighting, electric lighting systems, LED for plant growth, and carbon nanotube fiber filaments.

  5. Fusion reactor materials

    Energy Technology Data Exchange (ETDEWEB)

    none,

    1989-01-01

    This paper discuses the following topics on fusion reactor materials: irradiation, facilities, test matrices, and experimental methods; dosimetry, damage parameters, and activation calculations; materials engineering and design requirements; fundamental mechanical behavior; radiation effects; development of structural alloys; solid breeding materials; and ceramics.

  6. Isotope research materials

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    Preparation of research isotope materials is described. Topics covered include: separation of tritium from aqueous effluents by bipolar electrolysis; stable isotope targets and research materials; radioisotope targets and research materials; preparation of an 241 Am metallurgical specimen; reactor dosimeters; ceramic and cermet development; fission-fragment-generating targets of 235 UO 2 ; and wire dosimeters for Westinghouse--Bettis

  7. Fusion reactor materials

    International Nuclear Information System (INIS)

    1989-01-01

    This paper discuses the following topics on fusion reactor materials: irradiation, facilities, test matrices, and experimental methods; dosimetry, damage parameters, and activation calculations; materials engineering and design requirements; fundamental mechanical behavior; radiation effects; development of structural alloys; solid breeding materials; and ceramics

  8. Optimal Super Dielectric Material

    Science.gov (United States)

    2015-09-01

    plate capacitor will reduce the net field to an unprecedented extent. This family of materials can form materials with dielectric values orders of... Capacitor -Increase Area (A)............8 b. Multi-layer Ceramic Capacitor -Decrease Thickness (d) .......10 c. Super Dielectric Material-Increase...circuit modeling, from [44], and B) SDM capacitor charge and discharge ...................................................22 Figure 15. Dielectric

  9. Raw material versus processing

    International Nuclear Information System (INIS)

    Berg, E.A.T.

    1989-01-01

    Some brazilian aspects related with the obtainment of raw materials for advanced ceramic products are described. The necessity of import raw materials by the advanced ceramic industries is mentioned, generating dangerous depedence for the country. The brazilian mineral reserves for using in raw materials of advanced ceramic are also cited. (C.G.C.) [pt

  10. Chemicals in material cycles

    DEFF Research Database (Denmark)

    Pivnenko, Kostyantyn; Eriksson, Eva; Astrup, Thomas Fruergaard

    2015-01-01

    Material recycling has been found beneficial in terms of resource and energy performance and is greatly promoted throughout the world. A variety of chemicals is used in materials as additives and data on their presence is sparse. The present work dealt with paper as recyclable material and diisob...

  11. Materials science and architecture

    Science.gov (United States)

    Bechthold, Martin; Weaver, James C.

    2017-12-01

    Materiality — the use of various materials in architecture — has been fundamental to the design and construction of buildings, and materials science has traditionally responded to needs formulated by design, engineering and construction professionals. Material properties and processes are shaping buildings and influencing how they perform. The advent of technologies such as digital fabrication, robotics and 3D printing have not only accelerated the development of new construction solutions, but have also led to a renewed interest in materials as a catalyst for novel architectural design. In parallel, materials science has transformed from a field that explains materials to one that designs materials from the bottom up. The conflation of these two trends is giving rise to materials-based design research in which architects, engineers and materials scientists work as partners in the conception of new materials systems and their applications. This Review surveys this development for different material classes (wood, ceramics, metals, concrete, glass, synthetic composites and polymers), with an emphasis on recent trends and innovations.

  12. Cathodoluminescence | Materials Science | NREL

    Science.gov (United States)

    shown on a computer screen; the image of a sample semiconductor material appears as a striated oval material sample shown above; the image is a high-contrast light and dark oval on a dark background and was top left of copper indium gallium selenide semiconductor material sample; the image is shown on a

  13. Tailored Porous Materials

    Energy Technology Data Exchange (ETDEWEB)

    BARTON,THOMAS J.; BULL,LUCY M.; KLEMPERER,WALTER G.; LOY,DOUGLAS A.; MCENANEY,BRIAN; MISONO,MAKOTO; MONSON,PETER A.; PEZ,GUIDO; SCHERER,GEORGE W.; VARTULI,JAMES C.; YAGHI,OMAR M.

    1999-11-09

    Tailoring of porous materials involves not only chemical synthetic techniques for tailoring microscopic properties such as pore size, pore shape, pore connectivity, and pore surface reactivity, but also materials processing techniques for tailoring the meso- and the macroscopic properties of bulk materials in the form of fibers, thin films and monoliths. These issues are addressed in the context of five specific classes of porous materials: oxide molecular sieves, porous coordination solids, porous carbons, sol-gel derived oxides, and porous heteropolyanion salts. Reviews of these specific areas are preceded by a presentation of background material and review of current theoretical approaches to adsorption phenomena. A concluding section outlines current research needs and opportunities.

  14. Fusion Reactor Materials

    International Nuclear Information System (INIS)

    Decreton, M.

    2002-01-01

    The objective of SCK-CEN's programme on fusion reactor materials is to contribute to the knowledge on the radiation-induced behaviour of fusion reactor materials and components as well as to help the international community in building the scientific and technical basis needed for the construction of the future reactor. Ongoing projects include: the study of the mechanical and chemical (corrosion) behaviour of structural materials under neutron irradiation and water coolant environment; the investigation of the characteristics of irradiated first wall material such as beryllium; investigations on the management of materials resulting from the dismantling of fusion reactors including waste disposal. Progress and achievements in these areas in 2001 are discussed

  15. Advances in electronic materials

    CERN Document Server

    Kasper, Erich; Grimmeiss, Hermann G

    2008-01-01

    This special-topic volume, Advances in Electronic Materials, covers various fields of materials research such as silicon, silicon-germanium hetero-structures, high-k materials, III-V semiconductor alloys and organic materials, as well as nano-structures for spintronics and photovoltaics. It begins with a brief summary of the formative years of microelectronics; now the keystone of information technology. The latter remains one of the most important global technologies, and is an extremely complex subject-area. Although electronic materials are primarily associated with computers, the internet

  16. New materials in defence

    International Nuclear Information System (INIS)

    Khan, Sikandar S.; Khan, Shahid A.; Butt, N.M.

    1992-01-01

    National defence is very important and always needs new such materials which have technological and socio-economic development of human society. The types of materials used by a society reflect its level of sophistication. These modern materials are basically the same conventional materials but with a greater knowledge content which include superalloys, modern polymers, engineering ceramics and the advanced composite. The production and use of new materials is playing and important role in the recent development in the defence industry. (A.B.)

  17. Advanced Industrial Materials Program

    Science.gov (United States)

    Stooksbury, F.

    1994-06-01

    The mission of the Advanced Industrial Materials (AIM) program is to commercialize new/improved materials and materials processing methods that will improve energy efficiency, productivity, and competitiveness. Program investigators in the DOE national laboratories are working with about 100 companies, including 15 partners in CRDA's. Work is being done on intermetallic alloys, ceramic composites, metal composites, polymers, engineered porous materials, and surface modification. The program supports other efforts in the Office of Industrial Technologies to assist the energy-consuming process industries. The aim of the AIM program is to bring materials from basic research to industrial application to strengthen the competitive position of US industry and save energy.

  18. Methods of materiality

    DEFF Research Database (Denmark)

    Aagaard, Jesper; Matthiesen, Noomi Christine Linde

    2016-01-01

    that researchers should start paying attention to the material world (consisting of both human bodies and material objects) and what it means for how people live their lives. It is argued that this can be done by incorporating the concept of material presence to capture embodied and material layers of existence......This article challenges the hegemonic status of “language” as the primary substance of qualitative research in psychology, whether through interviews or recordings of naturally occurring talk. It thereby questions the overt focus on analyzing linguistic “meaning.” Instead, it is suggested...... practical guidelines for incorporating attention to materiality in qualitative research....

  19. Modelling of thermoelectric materials

    DEFF Research Database (Denmark)

    Bjerg, Lasse

    In order to discover new good thermoelectric materials, there are essentially two ways. One way is to go to the laboratory, synthesise a new material, and measure the thermoelectric properties. The amount of compounds, which can be investigated this way is limited because the process is time...... consuming. Another approach is to model the thermoelectric properties of a material on a computer. Several crystal structures can be investigated this way without use of much man power. I have chosen the latter approach. Using density functional theory I am able to calculate the band structure of a material....... This band structure I can then use to calculate the thermoelectric properties of the material. With these results I have investigated several materials and found the optimum theoretical doping concentration. If materials with these doping concentrations be synthesised, considerably better thermoelectric...

  20. IAEA biological reference materials

    International Nuclear Information System (INIS)

    Parr, R.M.; Schelenz, R.; Ballestra, S.

    1988-01-01

    The Analytical Quality Control Services programme of the IAEA encompasses a wide variety of intercomparisons and reference materials. This paper reviews only those aspects of the subject having to do with biological reference materials. The 1988 programme foresees 13 new intercomparison exercises, one for major, minor and trace elements, five for radionuclides, and seven for stable isotopes. Twenty-two natural matrix biological reference materials are available: twelve for major, minor and trace elements, six for radionuclides, and four for chlorinated hydrocarbons. Seven new intercomparisons and reference materials are in preparation or under active consideration. Guidelines on the correct use of reference materials are being prepared for publication in 1989 in consultation with other major international producers and users of biological reference materials. The IAEA database on available reference materials is being updated and expanded in scope, and a new publication is planned for 1989. (orig.)

  1. Articulating Material Criteria

    DEFF Research Database (Denmark)

    Hasling, Karen Marie

    2013-01-01

    , imitate and articulate the students’ inclusion of materials. This paper particularly discusses the experiences made and ideas generated after the execution of a material science course for second year students, with emphasis on the concept of the material selection matrix as an educational tool......This paper discusses the experiences and potentials with materials teaching at the Institute for Product Design at Kolding School of Design, using materials teaching as experiments in my PhD project. The project intents to create a stronger material awareness among product design students...... with emphasis on sustainability. The experiments aim to develop an understanding of, how product design students include materials in their design practice and how tools can be developed that further enhance this. Hence experiments are essential for the progress of the PhD project as they help to observe...

  2. Contact materials for nanoelectronics

    KAUST Repository

    Alshareef, Husam N.

    2011-02-01

    In this article, we review current research activities in contact material development for electronic and nanoelectronic devices. A fundamental issue in contact materials research is to understand and control interfacial reactions and phenomena that modify the expected device performance. These reactions have become more challenging and more difficult to control as new materials have been introduced and as device sizes have entered the deep nanoscale. To provide an overview of this field of inquiry, this issue of MRS Bulletin includes articles on gate and contact materials for Si-based devices, junction contact materials for Si-based devices, and contact materials for alternate channel substrates (Ge and III-V), nanodevices. © 2011 Materials Research Society.

  3. Comprehensive hard materials

    CERN Document Server

    2014-01-01

    Comprehensive Hard Materials deals with the production, uses and properties of the carbides, nitrides and borides of these metals and those of titanium, as well as tools of ceramics, the superhard boron nitrides and diamond and related compounds. Articles include the technologies of powder production (including their precursor materials), milling, granulation, cold and hot compaction, sintering, hot isostatic pressing, hot-pressing, injection moulding, as well as on the coating technologies for refractory metals, hard metals and hard materials. The characterization, testing, quality assurance and applications are also covered. Comprehensive Hard Materials provides meaningful insights on materials at the leading edge of technology. It aids continued research and development of these materials and as such it is a critical information resource to academics and industry professionals facing the technological challenges of the future. Hard materials operate at the leading edge of technology, and continued res...

  4. Multicomponent polymeric materials

    CERN Document Server

    Thomas, Sabu; Saha, Prosenjit

    2016-01-01

    The book offers an in-depth review of the materials design and manufacturing processes employed in the development of multi-component or multiphase polymer material systems. This field has seen rapid growth in both academic and industrial research, as multiphase materials are increasingly replacing traditional single-component materials in commercial applications. Many obstacles can be overcome by processing and using multiphase materials in automobile, construction, aerospace, food processing, and other chemical industry applications. The comprehensive description of the processing, characterization, and application of multiphase materials presented in this book offers a world of new ideas and potential technological advantages for academics, researchers, students, and industrial manufacturers from diverse fields including rubber engineering, polymer chemistry, materials processing and chemical science. From the commercial point of view it will be of great value to those involved in processing, optimizing an...

  5. Matter and materials

    International Nuclear Information System (INIS)

    Lefevre, J.

    1997-01-01

    This paper is an introduction to the materials used in nuclear engineering from the uranium (extraction, processing, ultimate use) to all radioactive products encountered in nuclear processes and more particularly those having particular applications or presenting particular risks in their ultimate disposal. This introduction gives a general presentation of the different topics which are developed in other chapters: nuclear materials and fuel cycle (fuel fabrication, actinides and recycling, direct storage and reprocessing of spent fuels, management of radioactive wastes, transport of radioactive materials, production and use of radioelements in the industry and medicine), moderators and coolants, other materials used in reactors (fuel cladding materials, special steels, zircaloy, neutron absorbent materials), and the mechanical behaviour of materials (steels, concretes). (J.S.)

  6. Superconductors and electrotechnical materials

    Energy Technology Data Exchange (ETDEWEB)

    Stanculescu, V

    1975-07-01

    A description is given of the properties of superconducting materials and of other materials which will be used in low temperature electrical engineering. The electrical and magnetic properties of type 1 or soft and type 2 or hard superconducting materials are analyzed. Electroinsulating and magnetic materials at low temperatures are also surveyed. Emphasis is placed on gaseous and fluid dielectric substances which retain their condition of physical aggregation at low temperatures and provide a cryogenic medium. These include helium, hydrogen, and nitrogen. As for solid dielectrics, satisfactory electroinsulating materials in terms of mechanical and electrical properties include the category of thermoplastic organic materials such as mylar, teflon, kapton, and nylon. It is also emphasized that cryoelectrical engineering requires magnetic materials with high magnetic induction at low temperatures, coercive field and low magnetic loss.

  7. Comprehensive nuclear materials

    CERN Document Server

    Allen, Todd; Stoller, Roger; Yamanaka, Shinsuke

    2012-01-01

    Comprehensive Nuclear Materials encapsulates a panorama of fundamental information on the vast variety of materials employed in the broad field of nuclear technology. The work addresses, in five volumes, 3,400 pages and over 120 chapter-length articles, the full panorama of historical and contemporary international research in nuclear materials, from Actinides to Zirconium alloys, from the worlds' leading scientists and engineers. It synthesizes the most pertinent research to support the selection, assessment, validation and engineering of materials in extreme nuclear environments. The work discusses the major classes of materials suitable for usage in nuclear fission, fusion reactors and high power accelerators, and for diverse functions in fuels, cladding, moderator and control materials, structural, functional, and waste materials.

  8. Biological materials: a materials science approach.

    Science.gov (United States)

    Meyers, Marc A; Chen, Po-Yu; Lopez, Maria I; Seki, Yasuaki; Lin, Albert Y M

    2011-07-01

    The approach used by Materials Science and Engineering is revealing new aspects in the structure and properties of biological materials. The integration of advanced characterization, mechanical testing, and modeling methods can rationalize heretofore unexplained aspects of these structures. As an illustration of the power of this methodology, we apply it to biomineralized shells, avian beaks and feathers, and fish scales. We also present a few selected bioinspired applications: Velcro, an Al2O3-PMMA composite inspired by the abalone shell, and synthetic attachment devices inspired by gecko. Copyright © 2010 Elsevier Ltd. All rights reserved.

  9. Materials 2014: a great success for materials sector

    International Nuclear Information System (INIS)

    Isnard, Olivier; Crepin, Jerome

    2014-01-01

    In this work are presented the summaries of the 19 symposiums presented at the conference: 'Materials 2014' and whose topics were: eco-materials, materials for energy storage and conversion, strategic materials, rare elements and recycling, surfaces functionalization and physico-chemical characterization, interfaces and coatings, corrosion, aging, durability, damage mechanical behaviours, disordered materials, glasses and their functionalization, materials and health, functional materials, porous, granular and with a high surface area materials, nano-materials, nano-structured systems, assembling processes, carbonaceous materials, great instruments and studies of materials, materials in severe conditions, powder forming processes, metallic materials and structures lightening. (O.M.)

  10. The Time of Materiality

    Directory of Open Access Journals (Sweden)

    Estrid Sørensen

    2007-01-01

    Full Text Available While time and space form a classic duality in social science, this article demonstrates a perspective on time, space and materiality as a core trinity. As a prominent figure in contemporary discussions on materiality in the social sciences Science and Technology Studies (STS emphasizes relational approaches. STS however lacks a clear relational definition of materiality and tends instead to focus on the agency of entities, on for instance material agency. The article suggests a relational definition of materiality and notes that this move implies turning the question of the time of materiality into an empirical question. It is argued that relational materiality must be studied spatially, and thus a spatial approach describing patterns of relations is presented. Based on field work in a primary school classroom and computer lab, three materials are analyzed: the blackboard, a bed-loft and an online 3D virtual environment. The empirical descriptions depict three different materialities, and it is shown how time is formed differently in each of them. Time, it is argued, is an emergent and characterizing aspect of materialities as spatial formations. URN: urn:nbn:de:0114-fqs070122

  11. Ceramic piezoelectric materials

    International Nuclear Information System (INIS)

    Kaszuwara, W.

    2004-01-01

    Ceramic piezoelectric materials conert reversibility electric energy into mechanical energy. In the presence of electric field piezoelectric materials exhibit deformations up to 0.15% (for single crystals up to 1.7%). The deformation energy is in the range of 10 2 - 10 3 J/m 3 and working frequency can reach 10 5 Hz. Ceramic piezoelectric materials find applications in many modern disciplines such as: automatics, micromanipulation, measuring techniques, medical diagnostics and many others. Among the variety of ceramic piezoelectric materials the most important appear to be ferroelectric materials such as lead zirconate titanate so called PZT ceramics. Ceramic piezoelectric materials can be processed by methods widely applied for standard ceramics, i.e. starting from simple precursors e.g. oxides. Application of sol-gel method has also been reported. Substantial drawback for many applications of piezoelectric ceramics is their brittleness, thus much effort is currently being put in the development of piezoelectric composite materials. Other important research directions in the field of ceramic piezoelectric materials composite development of lead free materials, which can exhibit properties similar to the PZT ceramics. Among other directions one has to state processing of single crystals and materials having texture or gradient structure. (author)

  12. Uranium reference materials

    International Nuclear Information System (INIS)

    Donivan, S.; Chessmore, R.

    1987-07-01

    The Technical Measurements Center has prepared uranium mill tailings reference materials for use by remedial action contractors and cognizant federal and state agencies. Four materials were prepared with varying concentrations of radionuclides, using three tailings materials and a river-bottom soil diluent. All materials were ground, dried, and blended thoroughly to ensure homogeneity. The analyses on which the recommended values for nuclides in the reference materials are based were performed, using independent methods, by the UNC Geotech (UNC) Chemistry Laboratory, Grand Junction, Colorado, and by C.W. Sill (Sill), Idaho National Engineering Laboratory, Idaho Falls, Idaho. Several statistical tests were performed on the analytical data to characterize the reference materials. Results of these tests reveal that the four reference materials are homogeneous and that no large systematic bias exists between the analytical methods used by Sill and those used by TMC. The average values for radionuclides of the two data sets, representing an unbiased estimate, were used as the recommended values for concentrations of nuclides in the reference materials. The recommended concentrations of radionuclides in the four reference materials are provided. Use of these reference materials will aid in providing uniform standardization among measurements made by remedial action contractors. 11 refs., 9 tabs

  13. Computational materials design

    International Nuclear Information System (INIS)

    Snyder, R.L.

    1999-01-01

    Full text: Trial and error experimentation is an extremely expensive route to the development of new materials. The coming age of reduced defense funding will dramatically alter the way in which advanced materials have developed. In the absence of large funding we must concentrate on reducing the time and expense that the R and D of a new material consumes. This may be accomplished through the development of computational materials science. Materials are selected today by comparing the technical requirements to the materials databases. When existing materials cannot meet the requirements we explore new systems to develop a new material using experimental databases like the PDF. After proof of concept, the scaling of the new material to manufacture requires evaluating millions of parameter combinations to optimize the performance of the new device. Historically this process takes 10 to 20 years and requires hundreds of millions of dollars. The development of a focused set of computational tools to predict the final properties of new materials will permit the exploration of new materials systems with only a limited amount of materials characterization. However, to bound computational extrapolations, the experimental formulations and characterization will need to be tightly coupled to the computational tasks. The required experimental data must be obtained by dynamic, in-situ, very rapid characterization. Finally, to evaluate the optimization matrix required to manufacture the new material, very rapid in situ analysis techniques will be essential to intelligently monitor and optimize the formation of a desired microstructure. Techniques and examples for the rapid real-time application of XRPD and optical microscopy will be shown. Recent developments in the cross linking of the world's structural and diffraction databases will be presented as the basis for the future Total Pattern Analysis by XRPD. Copyright (1999) Australian X-ray Analytical Association Inc

  14. Heterogeneous Materials I and Heterogeneous Materials II

    International Nuclear Information System (INIS)

    Knowles, K M

    2004-01-01

    In these two volumes the author provides a comprehensive survey of the various mathematically-based models used in the research literature to predict the mechanical, thermal and electrical properties of hetereogeneous materials, i.e., materials containing two or more phases such as fibre-reinforced polymers, cast iron and porous ceramic kiln furniture. Volume I covers linear properties such as linear dielectric constant, effective electrical conductivity and elastic moduli, while Volume II covers nonlinear properties, fracture and atomistic and multiscale modelling. Where appropriate, particular attention is paid to the use of fractal geometry and percolation theory in describing the structure and properties of these materials. The books are advanced level texts reflecting the research interests of the author which will be of significant interest to research scientists working at the forefront of the areas covered by the books. Others working more generally in the field of materials science interested in comparing predictions of properties with experimental results may well find the mathematical level quite daunting initially, as it is apparent that the author assumes a level of mathematics consistent with that taught in final year undergraduate and graduate theoretical physics courses. However, for such readers it is well worth persevering because of the in-depth coverage to which the various models are subjected, and also because of the extensive reference lists at the back of both volumes which direct readers to the various source references in the scientific literature. Thus, for the wider materials science scientific community the two volumes will be a valuable library resource. While I would have liked to see more comparison with experimental data on both ideal and 'real' heterogeneous materials than is provided by the author and a discussion of how to model strong nonlinear current--voltage behaviour in systems such as zinc oxide varistors, my overall

  15. Review of K. P. Kostis's "Τα κακομαθημένα παιδιά της Ιστορίας": Η διαμόρφωση του νεοελληνικού κράτους 18ος-21ος αιώνας ["History’s spoiled children": The formation of the modern Greek state, 18th-21st centuries

    OpenAIRE

    Gekas, Sakis

    2014-01-01

    Kostas P. Kostis, "Τα κακομαθημένα παιδιά της Ιστορίας": Η διαμόρφωση του νεοελληνικού κράτους 18ος-21ος αιώνας ["History’s spoiled children": The formation of the modern Greek state, 18th-21st centuries], Athens: Polis, 2013. 898 pp.

  16. Micromechanics of hierarchical materials

    DEFF Research Database (Denmark)

    Mishnaevsky, Leon, Jr.

    2012-01-01

    A short overview of micromechanical models of hierarchical materials (hybrid composites, biomaterials, fractal materials, etc.) is given. Several examples of the modeling of strength and damage in hierarchical materials are summarized, among them, 3D FE model of hybrid composites...... with nanoengineered matrix, fiber bundle model of UD composites with hierarchically clustered fibers and 3D multilevel model of wood considered as a gradient, cellular material with layered composite cell walls. The main areas of research in micromechanics of hierarchical materials are identified, among them......, the investigations of the effects of load redistribution between reinforcing elements at different scale levels, of the possibilities to control different material properties and to ensure synergy of strengthening effects at different scale levels and using the nanoreinforcement effects. The main future directions...

  17. Radiation protecting clothing materials

    International Nuclear Information System (INIS)

    Mio, Kotaro; Ijiri, Yasuo.

    1986-01-01

    Purpose: To provide radiation protecting clothing materials excellent in mechanical strength, corrosion resistance, flexibility and flexing strength. Constitution: The radiation protecting clothing materials according to this invention has pure lead sheets comprising a thin pure lead foil of 50 to 150 μm and radiation resistant organic materials, for example, polyethylene with high neutron shielding effect disposed to one or both surfaces thereof. The material are excellent in the repeating bending fatigue and mechanical strength, corrosion resistance and flexibility and, accordingly, radiation protecting clothings prepared by using them along or laminating them also possess these excellent characteristics. Further, they are excellent in the handlability, particularly, durability to the repeated holding and extension, as well as are preferable in the physical movability and feeling upon putting. The clothing materials may be cut into an appropriate size, or stitched into clothings made by radiation-resistant materials. In this case, pure lead sheets are used in lamination. (Horiuchi, T.)

  18. Ultrasonic nondestructive materials characterization

    Science.gov (United States)

    Green, R. E., Jr.

    1986-01-01

    A brief review of ultrasonic wave propagation in solid materials is presented with consideration of the altered behavior in anisotropic and nonlinear elastic materials in comparison with isotropic and linear elastic materials. Some experimental results are described in which ultrasonic velocity and attenuation measurements give insight into materials microstructure and associated mechanical properties. Recent developments with laser beam non-contact generation and detection of ultrasound are presented. The results of several years of experimental measurements using high-power ultrasound are discussed, which provide substantial evidence of the inability of presently accepted theories to fully explain the interaction of ultrasound with solid materials. Finally, a special synchrotron X-ray topographic system is described which affords the possibility of observing direct interaction of ultrasonic waves with the microstructural features of real crystalline solid materials for the first time.

  19. Hysteresis in Magnetocaloric Materials

    DEFF Research Database (Denmark)

    von Moos, Lars

    , obtained at the initial low and final high field. However, in first order materials thermal entropy hysteresis loops are obtained through characterization, corresponding to measurements done in an increasing and a decreasing temperature mode. Indirectly determining the MCE through the use of the Maxwell...... order materials, taking the magnetic and thermal history dependence of material properties into account, as well as the heat production due to hysteretic losses. MnFe(P,As) and Gd5Si2Ge2 compounds are modelled and it is found that the Preisach approach is suitable to reproduce material behavior in both......In this thesis the effects of hysteresis on magnetocaloric material properties and their performance in magnetic refrigeration devices are investigated. This is done through an experimental and model study of first order magnetocaloric materials MnFe(P,As) and Gd5Si2Ge2. The experimental...

  20. Fusion reactor materials

    International Nuclear Information System (INIS)

    Rowcliffe, A.F.; Burn, G.L.; Knee', S.S.; Dowker, C.L.

    1994-02-01

    This is the fifteenth in a series of semiannual technical progress reports on fusion reactor materials. This report combines research and development activities which were previously reported separately in the following progress reports: Alloy Development for Irradiation Performance; Damage Analysis and Fundamental Studies; Special purpose Materials. These activities are concerned principally with the effects of the neutronic and chemical environment on the properties and performance of reactor materials; together they form one element of the overall materials programs being conducted in support of the Magnetic Fusion Energy Program of the U.S. Department of Energy. The Fusion Reactor Materials Program is a national effort involving several national laboratories, universities, and industries. The purpose of this series of reports is to provide a working technical record for the use of the program participants, and to provide a means of communicating the efforts of materials scientists to the rest of the fusion community, both nationally and worldwide

  1. Skateboard deck materials selection

    Science.gov (United States)

    Liu, Haoyu; Coote, Tasha; Aiolos; Charlie

    2018-03-01

    The goal of this project was to identify the ideal material for a skateboard deck under 200 in price, minimizing the weight. The material must have a fracture toughness of 5 MPa/m2, have a minimum lifetime of 10, 000 cycles and must not experience brittle fracture. Both single material and hybrid solutions were explored. When further selecting to minimize weight, woods were found to be the best material. Titanium alloy-wood composites were explored to determine the optimal percentage composition of each material.A sandwich panel hybrid of 50% titanium alloy and 50% wood (Ti-Wood) was found to be the optimum material, performing better than the currently used plywood.

  2. Characterization of dielectric materials

    Energy Technology Data Exchange (ETDEWEB)

    King, Danny J.; Babinec, Susan; Hagans, Patrick L.; Maxey, Lonnie C.; Payzant, Edward A.; Daniel, Claus; Sabau, Adrian S.; Dinwiddie, Ralph B.; Armstrong, Beth L.; Howe, Jane Y.; Wood, III, David L.; Nembhard, Nicole S.

    2017-06-27

    A system and a method for characterizing a dielectric material are provided. The system and method generally include applying an excitation signal to electrodes on opposing sides of the dielectric material to evaluate a property of the dielectric material. The method can further include measuring the capacitive impedance across the dielectric material, and determining a variation in the capacitive impedance with respect to either or both of a time domain and a frequency domain. The measured property can include pore size and surface imperfections. The method can still further include modifying a processing parameter as the dielectric material is formed in response to the detected variations in the capacitive impedance, which can correspond to a non-uniformity in the dielectric material.

  3. Auditing nuclear materials statements

    International Nuclear Information System (INIS)

    Anon.

    1973-01-01

    A standard that may be used as a guide for persons making independent examinations of nuclear materials statements or reports regarding inventory quantities on hand, receipts, production, shipment, losses, etc. is presented. The objective of the examination of nuclear materials statements by the independent auditor is the expression of an opinion on the fairness with which the statements present the nuclear materials position of a nuclear materials facility and the movement of such inventory materials for the period under review. The opinion is based upon an examination made in accordance with auditing criteria, including an evaluation of internal control, a test of recorded transactions, and a review of measured discards and materials unaccounted for (MUF). The standard draws heavily upon financial auditing standards and procedures published by the American Institute of Certified Public Accountants

  4. Basic Electromagnetism and Materials

    CERN Document Server

    Moliton, André

    2007-01-01

    Basic Electromagnetism and Materials is the product of many years of teaching basic and applied electromagnetism. This textbook can be used to teach electromagnetism to a wide range of undergraduate science majors in physics, electrical engineering or materials science. However, by making lesser demands on mathematical knowledge than competing texts, and by emphasizing electromagnetic properties of materials and their applications, this textbook is uniquely suited to students of materials science. Many competing texts focus on the study of propagation waves either in the microwave or optical domain, whereas Basic Electromagnetism and Materials covers the entire electromagnetic domain and the physical response of materials to these waves. Professor André Moliton is Director of the Unité de Microélectronique, Optoélectronique et Polymères (Université de Limoges, France), which brings together three groups studying the optoelectronics of molecular and polymer layers, micro-optoelectronic systems for teleco...

  5. Characterization of Nanophase Materials

    Science.gov (United States)

    Wang, Zhong Lin

    2000-01-01

    Engineering of nanophase materials and devices is of vital interest in electronics, semiconductors and optics, catalysis, ceramics and magnetism. Research associated with nanoparticles has widely spread and diffused into every field of scientific research, forming a trend of nanocrystal engineered materials. The unique properties of nanophase materials are entirely determined by their atomic scale structures, particularly the structures of interfaces and surfaces. Development of nanotechnology involves several steps, of which characterization of nanoparticles is indespensable to understand the behavior and properties of nanoparticles, aiming at implementing nanotechnolgy, controlling their behavior and designing new nanomaterials systems with super performance. The book will focus on structural and property characterization of nanocrystals and their assemblies, with an emphasis on basic physical approach, detailed techniques, data interpretation and applications. Intended readers of this comprehensive reference work are advanced graduate students and researchers in the field, who are specialized in materials chemistry, materials physics and materials science.

  6. Frontiers in Superconducting Materials

    CERN Document Server

    Narlikar, Anant V

    2005-01-01

    Frontiers in Superconducting Materials gives a state-of-the-art report of the most important topics of the current research in superconductive materials and related phenomena. It comprises 30 chapters written by renowned international experts in the field. It is of central interest to researchers and specialists in Physics and Materials Science, both in academic and industrial research, as well as advanced students. It also addresses electronic and electrical engineers. Even non-specialists interested in superconductivity might find some useful answers.

  7. Joining of advanced materials

    CERN Document Server

    Messler, Robert W

    1993-01-01

    Provides an unusually complete and readable compilation of the primary and secondary options for joining conventional materials in non-conventional ways. Provides unique coverage of adhesive bonding using both organic and inorganic adhesives, cements and mortars. Focuses on materials issues without ignoring issues related to joint design, production processing, quality assurance, process economics, and joining performance in service.Joining of advanced materials is a unique treatment of joining of both conventional and advanced metals andalloys, intermetallics, ceramics, glasses, polymers, a

  8. Leaching materials from cavities

    International Nuclear Information System (INIS)

    Hodgson, T.D.; Jordan, T.W.J.

    1980-01-01

    A material is leached from a cavity by contacting the material with a liquid and subjecting the liquid to a number of pressure cycles, each pressure cycle involving a decrease in pressure to cause boiling of the liquid, followed by a rise in pressure to inhibit the boiling. The method may include the step of heating the liquid to a temperature near to its boiling point. The material may be nuclear fuel pellets or calcium carbonate pellets. (author)

  9. Micromechanics of heterogeneous materials

    CERN Document Server

    Buryachenko, Valeriy

    2007-01-01

    Here is an accurate and timely account of micromechanics, which spans materials science, mechanical engineering, applied mathematics, technical physics, geophysics, and biology. The book features rigorous and unified theoretical methods of applied mathematics and statistical physics in the material science of microheterogeneous media. Uniquely, it offers a useful demonstration of the systematic and fundamental research of the microstructure of the wide class of heterogeneous materials of natural and synthetic nature.

  10. Alloy catalyst material

    DEFF Research Database (Denmark)

    2014-01-01

    The present invention relates to a novel alloy catalyst material for use in the synthesis of hydrogen peroxide from oxygen and hydrogen, or from oxygen and water. The present invention also relates to a cathode and an electrochemical cell comprising the novel catalyst material, and the process use...... of the novel catalyst material for synthesising hydrogen peroxide from oxygen and hydrogen, or from oxygen and water....

  11. Functionally graded materials

    CERN Document Server

    Mahamood, Rasheedat Modupe

    2017-01-01

    This book presents the concept of functionally graded materials as well as their use and different fabrication processes. The authors describe the use of additive manufacturing technology for the production of very complex parts directly from the three dimension computer aided design of the part by adding material layer after layer. A case study is also presented in the book on the experimental analysis of functionally graded material using laser metal deposition process.

  12. Absolute nuclear material assay

    Science.gov (United States)

    Prasad, Manoj K [Pleasanton, CA; Snyderman, Neal J [Berkeley, CA; Rowland, Mark S [Alamo, CA

    2010-07-13

    A method of absolute nuclear material assay of an unknown source comprising counting neutrons from the unknown source and providing an absolute nuclear material assay utilizing a model to optimally compare to the measured count distributions. In one embodiment, the step of providing an absolute nuclear material assay comprises utilizing a random sampling of analytically computed fission chain distributions to generate a continuous time-evolving sequence of event-counts by spreading the fission chain distribution in time.

  13. Superconducting composites materials

    International Nuclear Information System (INIS)

    Kerjouan, P.; Boterel, F.; Lostec, J.; Bertot, J.P.; Haussonne, J.M.

    1991-01-01

    The new superconductor materials with a high critical current own a large importance as well in the electronic components or in the electrotechnical devices fields. The deposit of such materials with the thick films technology is to be more and more developed in the years to come. Therefore, we tried to realize such thick films screen printed on alumina, and composed mainly of the YBa 2 Cu 3 O 7-δ material. We first realized a composite material glass/YBa 2 Cu 3 O 7-δ , by analogy with the classical screen-printed inks where the glass ensures the bonding with the substrate. We thus realized different materials by using some different classes of glass. These materials owned a superconducting transition close to the one of the pure YBa 2 Cu 3 O 7-δ material. We made a slurry with the most significant composite materials and binders, and screen-printed them on an alumina substrate preliminary or not coated with a diffusion barrier layer. After firing, we studied the thick films adhesion, the alumina/glass/composite material interfaces, and their superconducting properties. 8 refs.; 14 figs.; 9 tabs [fr

  14. Materials Science Laboratory

    Science.gov (United States)

    Jackson, Dionne

    2005-01-01

    The NASA Materials Science Laboratory (MSL) provides science and engineering services to NASA and Contractor customers at KSC, including those working for the Space Shuttle. International Space Station. and Launch Services Programs. These services include: (1) Independent/unbiased failure analysis (2) Support to Accident/Mishap Investigation Boards (3) Materials testing and evaluation (4) Materials and Processes (M&P) engineering consultation (5) Metrology (6) Chemical analysis (including ID of unknown materials) (7) Mechanical design and fabrication We provide unique solutions to unusual and urgent problems associated with aerospace flight hardware, ground support equipment and related facilities.

  15. Materials characterization techniques

    National Research Council Canada - National Science Library

    Zhang, Sam; Li, L; Kumar, Ashok

    2009-01-01

    "With an emphasis on practical applications and real-world case studies, Materials Characterization Techniques presents the principles of widely used advanced surface and structural characterization...

  16. Materials Characterization Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Materials Characterization Facility enables detailed measurements of the properties of ceramics, polymers, glasses, and composites. It features instrumentation...

  17. Smuggling special nuclear materials

    International Nuclear Information System (INIS)

    Lazaroiu, Gheorghe

    1999-01-01

    Ever since the collapse of the former Soviet Union reports have circulated with increasing frequency concerning attempts to smuggle materials from that country's civil and military nuclear programs. Such an increase obviously raises a number of concerns (outlined in the author's introduction), chief among which is the possibility that these materials might eventually fall into the hands of proliferant states or terrorist groups. The following issues are presented: significance of materials being smuggled; sources and smuggling routes; potential customers; international efforts to reduce nuclear smuggling; long-term disposition of fissile materials. (author)

  18. Materials development for TESOL

    CERN Document Server

    Mishan, Freda

    2015-01-01

    Materials development has become much more important in the field of TESOL in the last twenty years: modules on materials development are now commonplace on MA TESOL courses around the world. The overall aim of the book is to introduce readers to a wide range of theoretical and practical issues in materials development to enable them to make informed and principled choices in the selection, evaluation, adaptation and production of materials. The book aims to show how these choices need to be informed by an awareness of culture, context and purpose.

  19. Materials information data bank

    International Nuclear Information System (INIS)

    Mead, K.E.

    1978-03-01

    A major concern in the design of weapons systems is compatibility of materials with each other and with the enclosed environment. Usually these systems require long-term storage and must have high reliability at the end of this storage period. Materials selection is thus based on past experience and on laboratory-accelerated testing to assure this long-term reliability. To assist in materials selection, a computerized materials data bank has been established. In addition to references on personnel and documents, this data bank provides annotated information on materials so that the designer and materials engineer can draw on it for guidance in selecting materials. The primary purpose of the data bank is to provide materials compatibility data. However, the structure of the system permits the data bank to be used for storage and retrieval of general materials information. The data bank storage and information retrieval philosophy is discussed and procedures for information gathering are outlined. Examples of data entries and a list of search routines are presented to demonstrate the usefulness and versatility of the system

  20. Reactor Materials Research

    Energy Technology Data Exchange (ETDEWEB)

    Van Walle, E

    2002-04-01

    The activities of SCK-CEN's Reactor Materials Research Department for 2001 are summarised. The objectives of the department are: (1) to evaluate the integrity and behaviour of structural materials used in nuclear power industry; (2) to conduct research to unravel and understand the parameters that determine the material behaviour under or after irradiation; (3) to contribute to the interpretation, the modelling of the material behaviour and to develop and assess strategies for optimum life management of nuclear power plant components. The programmes within the department are focussed on studies concerning (1) Irradiation Assisted Stress Corrosion Cracking (IASCC); (2) nuclear fuel; and (3) Reactor Pressure Vessel Steel.

  1. Reactor Materials Research

    International Nuclear Information System (INIS)

    Van Walle, E.

    2002-01-01

    The activities of SCK-CEN's Reactor Materials Research Department for 2001 are summarised. The objectives of the department are: (1) to evaluate the integrity and behaviour of structural materials used in nuclear power industry; (2) to conduct research to unravel and understand the parameters that determine the material behaviour under or after irradiation; (3) to contribute to the interpretation, the modelling of the material behaviour and to develop and assess strategies for optimum life management of nuclear power plant components. The programmes within the department are focussed on studies concerning (1) Irradiation Assisted Stress Corrosion Cracking (IASCC); (2) nuclear fuel; and (3) Reactor Pressure Vessel Steel

  2. Soft-Material Robotics

    OpenAIRE

    Wang, L; Nurzaman, SG; Iida, Fumiya

    2017-01-01

    There has been a boost of research activities in robotics using soft materials in the past ten years. It is expected that the use and control of soft materials can help realize robotic systems that are safer, cheaper, and more adaptable than the level that the conventional rigid-material robots can achieve. Contrary to a number of existing review and position papers on soft-material robotics, which mostly present case studies and/or discuss trends and challenges, the review focuses on the fun...

  3. Material for radioactive protection

    Science.gov (United States)

    Taylor, R.S.; Boyer, N.W.

    A boron containing burn resistant, low-level radiation protection material useful, for example, as a liner for radioactive waste disposal and storage, a component for neutron absorber, and a shield for a neutron source is described. The material is basically composed of borax in the range of 25 to 50%, coal tar in the range of 25 to 37.5%, with the remainder being an epoxy resin mix. A preferred composition is 50% borax, 25% coal tar and 25% epoxy resin. The material is not susceptible to burning and is about 1/5 the cost of existing radiation protection material utilized in similar applications.

  4. Materials Behavior Research Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The purpose is to evaluate mechanical properties of materials including metals, intermetallics, metal-matrix composites, and ceramic-matrix composites under typical...

  5. Fusion Reactor Materials

    International Nuclear Information System (INIS)

    Decreton, M.

    2001-01-01

    The objective of SCK-CEN's programme on fusion reactor materials is to contribute to the knowledge on the behaviour of fusion reactor materials and components during and after irradiation. Ongoing projects include: the study of the mechanical behaviour of structural materials under neutron irradiation; the investigation of the characteristics of irradiated first wall material such as beryllium; the detection of abrupt electrical degradation of insulating ceramics under high temperature and neutron irradiation; and the study of dismantling and waste disposal strategy for fusion reactors. Progress and achievements in these areas in 2000 are discussed

  6. Thermoelectric materials having porosity

    Science.gov (United States)

    Heremans, Joseph P.; Jaworski, Christopher M.; Jovovic, Vladimir; Harris, Fred

    2014-08-05

    A thermoelectric material and a method of making a thermoelectric material are provided. In certain embodiments, the thermoelectric material comprises at least 10 volume percent porosity. In some embodiments, the thermoelectric material has a zT greater than about 1.2 at a temperature of about 375 K. In some embodiments, the thermoelectric material comprises a topological thermoelectric material. In some embodiments, the thermoelectric material comprises a general composition of (Bi.sub.1-xSb.sub.x).sub.u(Te.sub.1-ySe.sub.y).sub.w, wherein 0.ltoreq.x.ltoreq.1, 0.ltoreq.y.ltoreq.1, 1.8.ltoreq.u.ltoreq.2.2, 2.8.ltoreq.w.ltoreq.3.2. In further embodiments, the thermoelectric material includes a compound having at least one group IV element and at least one group VI element. In certain embodiments, the method includes providing a powder comprising a thermoelectric composition, pressing the powder, and sintering the powder to form the thermoelectric material.

  7. Materials for Slack Diaphragms

    Science.gov (United States)

    Puschmann, Traute

    1940-01-01

    This report deals with systematic experiments carried out on five diaphragm materials with different pretreatment, for the purpose of ascertaining the suitability of such materials for slack diaphragms. The relationship of deflection and load, temperature and moisture, was recorded. Of the explored materials, synthetic leather, balloon cloth, goldbeaters skin, Igelit and Buna, synthetic leather treated with castor oil is the most suitable material for the small pressure range required. Balloon cloth is nearly as good, while goldbeaters skin, Igelit and Buna were found to be below the required standards.

  8. Frontiers in Magnetic Materials

    CERN Document Server

    Narlikar, Anant V

    2005-01-01

    Frontiers in Magnetic Materials focuses on the current achievements and state-of-the-art advancements in magnetic materials. Several lines of development- High-Tc Superconductivity, Nanotechnology and refined experimental techniques among them – raised knowledge and interest in magnetic materials remarkably. The book comprises 24 chapters on the most relevant topics written by renowned international experts in the field. It is of central interest to researchers and specialists in Physics and Materials Science, both in academic and industrial research, as well as advanced students.

  9. The materialization of fear

    DEFF Research Database (Denmark)

    Jensen, Martin Trandberg

    to matter in ways not simply reducible to security optimization, risk management and symbolic politics? To reach this aim, I draw on material studies, mobilities design and non-representational theories to provide a rich socio-material tale of how granite stones, bollards and other counter......-terrorist materials contribute to the construction and ‘feel’ of contemporary urban tourism. How do such prominent material designs influence, both affectively, practically and emotionally, tourists? How are they re-appropriated and imbued with (inter)subjective meanings, and how may a richer understanding of how...

  10. Advanced thermal management materials

    CERN Document Server

    Jiang, Guosheng; Kuang, Ken

    2012-01-01

    ""Advanced Thermal Management Materials"" provides a comprehensive and hands-on treatise on the importance of thermal packaging in high performance systems. These systems, ranging from active electronically-scanned radar arrays to web servers, require components that can dissipate heat efficiently. This requires materials capable of dissipating heat and maintaining compatibility with the packaging and dye. Its coverage includes all aspects of thermal management materials, both traditional and non-traditional, with an emphasis on metal based materials. An in-depth discussion of properties and m

  11. Development of magnetic materials

    International Nuclear Information System (INIS)

    Bar'yakhtar, V.

    2000-01-01

    In the paper are presented both experimental and theoretical basic results of physics of magnetic materials. The special attention is given to a problem of creation of magnetic materials for recording and reproduction of the information. The influence of fundamental scientific results on process of creation of materials with the given properties and constriction of devices and facilities of new generation, and return influence of financing of scientific researches on process of discovering of new unknown fundamental properties of magnetic materials is considered. (author)

  12. [Materials for construction sector].

    Science.gov (United States)

    Macchia, C

    2012-01-01

    The construction sector is characterized by high complexity due to several factors. There are a lot of processes within the building sites and they need the use of different materials with the help of appropriate technologies. Traditional materials have evolved and diversified, meanwhile new products and materials appeared and still appear, offering services which meet user needs, but that often involve risks to the health of workers. Research in the field of materials, promoted and carried out at various levels, has led to interesting results, encoded in the form of rules and laws.

  13. Materials on the brink: unprecedented transforming materials

    Science.gov (United States)

    2013-09-10

    2013 56.00 Shenqiang Ren\\, Manfred Wuttig. Spinodal synthesis of PZT /NFO magnetoelectric, Applied Physics Letters, (08 2007): 83501. doi: 02/06/2013... PZT . This material was discovered through a combinatorial search. Rabe et al. have used first principles methods to show that this morphotropic...temperature. James et al. have suggested a new strategy for energy recovery from waste heat using this alloy. • Discovery of a new fatigue -free shape

  14. Is the materialization of architecture necessarily material?

    Directory of Open Access Journals (Sweden)

    Čarapić Ana

    2008-01-01

    Full Text Available Architectural dematerialization process has started in the first half of the previous century, and has intensively developed at the beginning of this one. Architectural form decomposition on homo­geneous envelope and dependent internal structure, affect on façade materials to liberate from the ballast of supported role, and to gain the privilege to be the main holder of symbolic and sensual dimension. Therefore, on semantic level, they became primary driving force of dematerialization of form, and architecture in the whole. With new technological development, continuity in 'relieving' of matter has been brought to the extreme. Striving for complete liberty of conventional firmness and stability (in functional and phenomenal mode architecture take over the efemer 'week' substances from nature: water, air light, sound, and turn them in it's proper frame. Therefore, the general thesis of this paper is the absurd of architectural materialization with it's on demateriality. Being brought to the turning point, this absurd transforms both architecture (as artificial matter as well as nature itself. The goal of this paper is to predicate principles of material, formal and architectural genesis, in relation to the theoretical sources, as well as by examples of two developed constructions (pavilion 'Blur building' by Diller & Skofidio, and 'Tower of sound' by Toyo Ito.

  15. Between material and ideas

    DEFF Research Database (Denmark)

    Dahlstedt, Palle

    2012-01-01

    between a dynamic concept and the changing material form of the work. Combining ideas, tools, material and memory, creativity is described as a coherent, dynamic, and iterative process that navigates the space of the chosen medium, guided by the tools at hand, and by the continuously revised ideas...

  16. Designing with residual materials

    NARCIS (Netherlands)

    Walhout, W.; Wever, R.; Blom, E.; Addink-Dölle, L.; Tempelman, E.

    2013-01-01

    Many entrepreneurial businesses have attempted to create value based on the residual material streams of third parties. Based on ‘waste’ materials they designed products, around which they built their company. Such activities have the potential to yield sustainable products. Many of such companies

  17. Materials modified by irradiation

    International Nuclear Information System (INIS)

    Chmielewski, A.G.

    2007-01-01

    Application of radiation in pharmaceutical sciences and cosmetology, polymer materials, food industry, environment, health camre products and packing production is described. Nano-technology is described more detailed, because it is less known as irradiation using technology. Economic influence of the irradiation on the materials value addition is shown

  18. Transport of Radioactive Materials

    International Nuclear Information System (INIS)

    2001-01-01

    This address overviews the following aspects: concepts on transport of radioactive materials, quantities used to limit the transport, packages, types of packages, labeling, index transport calculation, tags, labeling, vehicle's requirements and documents required to authorize transportation. These requirements are considered in the regulation of transport of radioactive material that is in drafting step

  19. Social character of materialism.

    Science.gov (United States)

    Chatterjee, A; Hunt, J M; Kernan, J B

    2000-06-01

    Scores for 170 undergraduates on Richins and Dawson's Materialism scale were correlated with scores on Kassarjian's Social Preference Scale, designed to measure individuals' character structure. A correlation of .26 between materialism and other-directed social character suggested that an externally oriented reference system guides materialists' perceptions, judgments, acquisitions, and possessions.

  20. Materials testing 1985

    International Nuclear Information System (INIS)

    1985-01-01

    The following subjects were dealt with at the meeting: Testing with vibration loads; Hardness testing; Calibration of test devices and equipment; Test technique for compound materials; Vibration strength testing and expense of experiments; Solving problems in introducing forces into samples and components and process of ambulant materials testing. There are 17 separate abstracts from among 43 lectures. (orig./PW) [de

  1. Light as experiential material

    DEFF Research Database (Denmark)

    Petersen, Kjell Yngve; Søndergaard, Karin

    2013-01-01

    'Light as experiential material' is concerned with the development of a psychophysical method of investigation, by which the experience and design of architectural lighting can be approached in research and education......'Light as experiential material' is concerned with the development of a psychophysical method of investigation, by which the experience and design of architectural lighting can be approached in research and education...

  2. Light as experiential material

    DEFF Research Database (Denmark)

    Søndergaard, Karin; Petersen, Kjell Yngve

    2013-01-01

    'Light as experiential material' is concerned with the development of a psychophysical method of investigation, by which we can approach the experience and design of architectural lighting in research and education.......'Light as experiential material' is concerned with the development of a psychophysical method of investigation, by which we can approach the experience and design of architectural lighting in research and education....

  3. Contemporary dielectric materials

    CERN Document Server

    Saravanan, R

    2016-01-01

    This book deals with experimental results of the physical characterization of several important, dielectric materials of great current interest. The experimental tools used for the analysis of these materials include X-ray diffraction, dielectric measurements, magnetic measurements using a vibrating sample magnetometer, optical measurements using a UV-Visible spectrometer etc.

  4. Designing through Material

    DEFF Research Database (Denmark)

    Kruse Aagaard, Anders

    2014-01-01

    as an opportunity to connect the digital environment with the reality of materials – and use realisation and materialisation to generate architectural developments and findings through an iterative mode of thinking about the dialogue between drawing, materials and fabrication. Consequently the interest and mind...

  5. Gravitation in Material Media

    Science.gov (United States)

    Ridgely, Charles T.

    2011-01-01

    When two gravitating bodies reside in a material medium, Newton's law of universal gravitation must be modified to account for the presence of the medium. A modified expression of Newton's law is known in the literature, but lacks a clear connection with existing gravitational theory. Newton's law in the presence of a homogeneous material medium…

  6. Structural and Material Instability

    DEFF Research Database (Denmark)

    Cifuentes, Gustavo Cifuentes

    This work is a small contribution to the general problem of structural and material instability. In this work, the main subject is the analysis of cracking and failure of structural elements made from quasi-brittle materials like concrete. The analysis is made using the finite element method. Three...

  7. Mechanical meta-materials

    NARCIS (Netherlands)

    Zadpoor, A.A.

    2016-01-01

    The emerging concept of mechanical meta-materials has received increasing attention during the last few years partially due to the advances in additive manufacturing techniques that have enabled fabricating materials with arbitrarily complex micro/nano-architectures. The rationally designed

  8. Impacted material placement plans

    International Nuclear Information System (INIS)

    Hickey, M.J.

    1997-01-01

    Impacted material placement plans (IMPP) are documents identifying the essential elements in placing remediation wastes into disposal facilities. Remediation wastes or impacted material(s) are those components used in the construction of the disposal facility exclusive of the liners and caps. The components might include soils, concrete, rubble, debris, and other regulatory approved materials. The IMPP provides the details necessary for interested parties to understand the management and construction practices at the disposal facility. The IMPP should identify the regulatory requirements from applicable DOE Orders, the ROD(s) (where a part of a CERCLA remedy), closure plans, or any other relevant agreements or regulations. Also, how the impacted material will be tracked should be described. Finally, detailed descriptions of what will be placed and how it will be placed should be included. The placement of impacted material into approved on-site disposal facilities (OSDF) is an integral part of gaining regulatory approval. To obtain this approval, a detailed plan (Impacted Material Placement Plan [IMPP]) was developed for the Fernald OSDF. The IMPP provides detailed information for the DOE, site generators, the stakeholders, regulatory community, and the construction subcontractor placing various types of impacted material within the disposal facility

  9. Radioactivity in building materials

    International Nuclear Information System (INIS)

    1985-01-01

    The present report, drawn up at the request of the former Minister of Public Health and Environmental Affairs of the Netherlands, discusses the potential radiological consequences for the population of the Netherlands of using waste materials as building materials in housing construction. (Auth.)

  10. Environmental materials and interfaces

    International Nuclear Information System (INIS)

    1991-11-01

    A workshop that explored materials and interfaces research needs relevant to national environmental concerns was conducted at Pacific Northwest Laboratory. The purposes of the workshop were to refine the scientific research directions being planned for the Materials and Interface Program in the Molecular Science Research Center (MSRC) and further define the research and user equipment to the included as part of the proposed Environmental and Molecular Science Laboratory (EMSL). Three plenary information sessions served to outline the background, objectives, and status of the MSRC and EMSL initiatives; selected specific areas with environmentally related materials; and the status of capabilities and facilities planned for the EMSL. Attention was directed to four areas where materials and interface science can have a significant impact on prevention and remediation of environmental problems: in situ detection and characterization of hazardous wastes (sensors), minimization of hazardous waste (separation membranes, ion exchange materials, catalysts), waste containment (encapsulation and barrier materials), and fundamental understanding of contaminant transport mechanisms. During all other sessions, the participants were divided into three working groups for detailed discussion and the preparation of a written report. The working groups focused on the areas of interface structure and chemistry, materials and interface stability, and materials synthesis. These recommendations and suggestions for needed research will be useful for other researchers in proposing projects and for suggesting collaborative work with MSRC researchers. 1 fig

  11. Fusion reactor materials

    International Nuclear Information System (INIS)

    Sethi, V.K.; Scholz, R.; Nolfi, F.V. Jr.; Turner, A.P.L.

    1980-01-01

    Data are given for each of the following areas: (1) effects of irradiation on fusion reactor materials, (2) hydrogen permeation and materials behavior in alloys, (3) carbon coatings for fusion applications, (4) surface damage of TiB 2 coatings under energetic D + and 4 He + irradiations, and (5) neutron dosimetry

  12. Sex Education Materials.

    Science.gov (United States)

    Singer-Magdoff, Laura

    1969-01-01

    After briefly discussing the philosophy of sex education and appraising generally the nature of the instructional methods and materials currently in use in the schools, the author provides brief but incisive reviews of a number of films, filmstrips, and other instructional materials dealing with sex. The reviews are continued in the succeeding…

  13. Scintillator material. Szintillatormaterial

    Energy Technology Data Exchange (ETDEWEB)

    Siegmund, M; Bendig, J; Regenstein, W

    1987-11-25

    A scintillator material for detection and quantitative determination of ionizing radiation is discussed consisting of an acridone dissolved in a fluid or solid medium. Solvent mixtures with at least one protogenic component or polymers and copolymers are used. The scintillator material is distinguished by an excellent stability at high energy doses.

  14. Detecting Illicit Nuclear Materials

    International Nuclear Information System (INIS)

    Kouzes, Richard T.

    2005-01-01

    The threat that weapons of mass destruction might enter the United States has led to a number of efforts for the detection and interdiction of nuclear, radiological, chemical, and biological weapons at our borders. There have been multiple deployments of instrumentation to detect radiation signatures to interdict radiological material, including weapons and weapons material worldwide

  15. The Materiality of Research

    DEFF Research Database (Denmark)

    Meier, Ninna

    2016-01-01

    In this feature essay, Ninna Meier reflects on the materiality of the writing – and re-writing – process in academic research. She explores the ways in which our ever-accummulating thoughts come to form layers on the material objects in which we write our notes and discusses the pleasures of co-authorship....

  16. Chemical Absorption Materials

    DEFF Research Database (Denmark)

    Thomsen, Kaj

    2011-01-01

    Chemical absorption materials that potentially can be used for post combustion carbon dioxide capture are discussed. They fall into five groups, alkanolamines, alkali carbonates, ammonia, amino acid salts, and ionic liquids. The chemistry of the materials is discussed and advantages and drawbacks...

  17. Material Tracking Using LANMAS

    International Nuclear Information System (INIS)

    Armstrong, F.

    2010-01-01

    LANMAS is a transaction-based nuclear material accountability software product developed to replace outdated and legacy accountability systems throughout the DOE. The core underlying purpose of LANMAS is to track nuclear materials inventory and report transactions (movement, mixing, splitting, decay, etc.) to the Nuclear Materials Management and Safeguards System (NMMSS). While LANMAS performs those functions well, there are many additional functions provided by the software product. As a material is received onto a site or created at a site, its entire lifecycle can be tracked in LANMAS complete to its termination of safeguards. There are separate functions to track material movements between and within material balance areas (MBAs). The level of detail for movements within a MBA is configurable by each site and can be as high as a site designation or as detailed as building/room/rack/row/position. Functionality exists to track the processing of materials, either as individual items or by modeling a bulk process as an individual item to track inputs and outputs from the process. In cases where sites have specialized needs, the system is designed to be flexible so that site specific functionality can be integrated into the product. This paper will demonstrate how the software can be used to input material into an account and track it to its termination of safeguards.

  18. The Computational Materials Repository

    DEFF Research Database (Denmark)

    Landis, David D.; Hummelshøj, Jens S.; Nestorov, Svetlozar

    2012-01-01

    The possibilities for designing new materials based on quantum physics calculations are rapidly growing, but these design efforts lead to a significant increase in the amount of computational data created. The Computational Materials Repository (CMR) addresses this data challenge and provides...

  19. The nuclear materials contraband

    International Nuclear Information System (INIS)

    Williams, P.; Woessner, P.

    1996-01-01

    Several seizures of nuclear materials carried by contraband have been achieved. Some countries or criminal organizations could manufacture atomic bombs and use them. This alarming situation is described into details. Only 40% of drugs are seized by the American police and probably less in western Europe. The nuclear materials market is smaller than the drugs'one but the customs has also less experience to intercept the uranium dispatch for instance more especially as the peddlers are well organized. A severe control of the international transports would certainly allow to seize a large part of nuclear contraband materials but some dangerous isotopes as uranium 235 or plutonium 239 are little radioactive and which prevents their detection by the Geiger-Mueller counters. In France, some regulations allow to control the materials used to manufacture the nuclear weapons, and diminish thus the risk of a nuclear materials contraband. (O.L.). 4 refs., 2 figs

  20. Negative thermal expansion materials

    International Nuclear Information System (INIS)

    Evans, J.S.O.

    1997-01-01

    The recent discovery of negative thermal expansion over an unprecedented temperature range in ZrW 2 O 8 (which contracts continuously on warming from below 2 K to above 1000 K) has stimulated considerable interest in this unusual phenomenon. Negative and low thermal expansion materials have a number of important potential uses in ceramic, optical and electronic applications. We have now found negative thermal expansion in a large new family of materials with the general formula A 2 (MO 4 ) 3 . Chemical substitution dramatically influences the thermal expansion properties of these materials allowing the production of ceramics with negative, positive or zero coefficients of thermal expansion, with the potential to control other important materials properties such as refractive index and dielectric constant. The mechanism of negative thermal expansion and the phase transitions exhibited by this important new class of low-expansion materials will be discussed. (orig.)

  1. Recycling fusion materials

    International Nuclear Information System (INIS)

    Ooms, L.

    2005-01-01

    The inherent safety and environmental advantages of fusion power in comparison with other energy sources play an important role in the public acceptance. No waste burden for future generations is therefore one of the main arguments to decide for fusion power. The waste issue has thus been studied in several documents and the final conclusion of which it is stated that there is no permanent disposal waste needed if recycling is applied. But recycling of fusion reactor materials is far to be obvious regarding mostly the very high specific activity of the materials to be handled, the types of materials and the presence of tritium. The main objective of research performed by SCK-CEN is to study the possible ways of recycling fusion materials and analyse the challenges of the materials management from fusion reactors, based on current practices used in fission reactors and the requirements for the manufacture of fusion equipment

  2. Fusion Reactor Materials

    Energy Technology Data Exchange (ETDEWEB)

    Decreton, M

    2002-04-01

    The objective of SCK-CEN's programme on fusion reactor materials is to contribute to the knowledge on the radiation-induced behaviour of fusion reactor materials and components as well as to help the international community in building the scientific and technical basis needed for the construction of the future reactor. Ongoing projects include: the study of the mechanical and chemical (corrosion) behaviour of structural materials under neutron irradiation and water coolant environment; the investigation of the characteristics of irradiated first wall material such as beryllium; investigations on the management of materials resulting from the dismantling of fusion reactors including waste disposal. Progress and achievements in these areas in 2001 are discussed.

  3. Materials and nanotechnology

    International Nuclear Information System (INIS)

    2014-01-01

    The focus of the Materials and Nanotechnology Program is technology development related to processing, analysis, testing and characterization of materials in general. These are achieved through execution of R&D projects in engineering and materials science, cooperative projects with private and public sector companies, universities and other research institutes. Besides technology development, this Program also fosters training and human resource development in association with the University of São Paulo and many industrial sectors. This Program is divided into sub-programs in broad areas such as ceramic, composite and metallic materials as well as characterization of physical and chemical properties of materials. The sub-programs are further divided into general topics and within each topic, R&D projects. A brief description of progress in each topic during the last three years follows. (author)

  4. Materials for advanced packaging

    CERN Document Server

    Wong, CP

    2017-01-01

    This second edition continues to be the most comprehensive review on the developments in advanced electronic packaging technologies, with a focus on materials and processing. Recognized experts in the field contribute to 22 updated and new chapters that provide comprehensive coverage on various 3D package architectures, novel bonding and joining techniques, wire bonding, wafer thinning techniques, organic substrates, and novel approaches to make electrical interconnects between integrated circuit and substrates. Various chapters also address advances in several key packaging materials, including: Lead-free solders Flip chip underfills Epoxy molding compounds Conductive adhesives Die attach adhesives/films Thermal interface materials (TIMS) Materials for fabricating embedded passives including capacitors, inductors, and resistors Materials and processing aspects on wafer-level chip scale package (CSP) and MicroElectroMechanical system (MEMS) Contributors also review new and emerging technologies such as Light ...

  5. Lasers in materials science

    CERN Document Server

    Ossi, Paolo; Zhigilei, Leonid

    2014-01-01

    This book covers various aspects of lasers in materials science, including a comprehensive overview on basic principles of laser-materials interactions and applications enabled by pulsed laser systems.  The material is organized in a coherent way, providing the reader with a harmonic architecture. While systematically covering the major current and emerging areas of lasers processing applications, the Volume provides examples of targeted modification of material properties achieved through careful control of the processing conditions and laser irradiation parameters. Special emphasis is placed on specific strategies aimed at nanoscale control of material structure and properties to match the stringent requirements of modern applications.  Laser fabrication of novel nanomaterials, which expands to the domains of photonics, photovoltaics, sensing, and biomedical applications, is also discussed in the Volume. This book assembles chapters based on lectures delivered at the Venice International School on Lasers...

  6. Of 'other' materialities

    DEFF Research Database (Denmark)

    Jensen, Ole B.

    2016-01-01

    within the ‘new materiality’ literature in philosophy as well as in cultural theory. Important lessons are drawn in from across different positions such as non-representational theory, the nonhuman turn, Object-Oriented-Ontology to mention a few. It is argued that to create the necessary materially......In this article, the notion of materialities is rearticulated as an important field for the future of mobilities research. We focus on the intersection between situational mobilities research and design/architecture. The vocabulary and material imaginary developed within the latter are an important...... sensitive imaginary, mobilities research should be looking to architecture and design, as well as it may profit from engaging with these new materially sensitive thinkers. The article ends with some concrete themes for future research inspired by these intersections and identifies ‘material pragmatism...

  7. Reactor pressure boundary materials

    International Nuclear Information System (INIS)

    Hong, Jun Hwa; Chi, S. H.; Lee, B. S.

    2002-04-01

    With a long-term operation of nuclear power plants, the component materials are degraded under severe reactor conditions such as neutron irradiation, high temperature, high pressure and corrosive environment. It is necessary to establish the reliable and practical technologies for improving and developing the component materials and for evaluating the mechanical properties. Especially, it is very important to investigate the technologies for reactor pressure boundary materials such as reactor vessel and pipings in accordance with their critical roles. Therefore, this study was focused on developing and advancing the microstructural/micro-mechanical evaluation technologies, and on evaluating the neutron irradiation characteristics and radiation effects analysis technology of the reactor pressure boundary materials, and also on establishing a basis of nuclear material property database

  8. Articulating Material Criteria

    DEFF Research Database (Denmark)

    Hasling, Karen Marie

    2013-01-01

    This paper discusses the experiences and potentials with materials teaching at the Institute for Product Design at Kolding School of Design, using materials teaching as experiments in my PhD project. The project intents to create a stronger material awareness among product design students...... with emphasis on sustainability. The experiments aim to develop an understanding of, how product design students include materials in their design practice and how tools can be developed that further enhance this. Hence experiments are essential for the progress of the PhD project as they help to observe....... Furthermore the purpose is to initiate a discussion on, how to create educational tools for material awareness creation in the design education e.g. by applying objective and quantitative methods in an otherwise often subjective design process....

  9. Sensitivity of spoiling and pathogen food-related bacteria to Origanum vulgare L. (Lamiaceae essential oil Sensibilidade de bactérias deteriorantes e patogênicas de interesse em alimentos ao óleo essencial de Origanum vulgare L. (Lamiaceae

    Directory of Open Access Journals (Sweden)

    Evandro Leite de Souza

    2006-12-01

    Full Text Available Origanum vulgare L. (oregano, Lamiaceae, has been known as plant specie with prominent biological properties for a long time. This study aimed to evaluate the antibacterial activity of Origanum vulgare essential oil on various Gram-positive and Gram-negative spoiling and/or pathogen food-related bacteria, as well as to observe its antimicrobial effectiveness in a food conservation micromodel. The results showed a strong antibacterial activity of the assayed essential oil noted by large growth inhibition zones (30-37 mm. MIC values were between 20-40 µL/mL for the most bacteria strains. Essential oil was able to cause significant (POriganum vulgare L. (orégano, Lamiaceae, tem sido reconhecida como uma espécie vegetal com destacáveis propriedades biológicas por um longo tempo. Este estudo objetivou avaliar a atividade antibacteriana do óleo essencial de Origanum vulgare L. sobre várias bactérias Gram positivas e Gram negativas deteriorantes e/ou patogênicas de interesse em alimentos, bem como observar sua efetividade antimicrobiana em um micromodelo de conservação de alimentos. Os resultados mostraram uma considerável atividade antibacteriana do óleo essencial ensaiado notada por grandes zonas de inibição do crescimento bacteriano (30-37 mm. Os valores de CIM encontrados oscilaram entre 20-40 µL/mL para a maioria das bactérias. A CIM do óleo essencial causou um significante (P<0.05 efeito inibitório sobre a viabilidade bacteriana, sendo caracterizado uma propriedade bacteriostática após 24 horas de exposição. Ainda, a CIM causou uma diminuição significante (P<0.05 da contagem da flora bacteriana autóctone em carne moída armazenada sob refrigeração. Estes dados suportam a possibilidade do uso do óleo essencial de Origanum vulgare L. como composto antimicrobiano alternativo em sistemas de conservação de alimentos.

  10. Utilization of waste of coal-mining enterprise in production of building materials

    Science.gov (United States)

    Chugunov, A. D.; Filatova, E. G.; Yakovleva, A. A.

    2018-03-01

    Wastes of coal producers often include substances allowing treating such wastes as valuable feeds for metallurgy, chemical and construction processes. This study concerned elemental and phase composition of samples obtained by calcination of bottom sediments of the coal producer spoil bank. The research has shown that the samples contain significant amounts of carbon, iron, silicon, aluminum and other valuable components.

  11. Security of material

    International Nuclear Information System (INIS)

    Nilsson, A.

    2001-01-01

    Full text: From the early days of discovery and experimentation with nuclear science, nuclear and radioactive materials have held extraordinary potential for being of great benefit to humankind, as well as for causing significant harm. For the past forty years, the IAEA has played an important role in ensuring that nuclear technologies and materials are used only for peaceful purposes. The Agency's safeguards programme has been providing assurances that States honour their undertakings to use nuclear facilities and materials for peaceful purposes only. The potential of nuclear materials and other radioactive materials being used in subversive activities, such as theft, illicit trafficking, sabotage and threats thereof, has been recognized by the international community. The tragic events in New York have given new light to and increased concern for this potential. No target may be considered immune from terrorism. Since 1993, States have confirmed over 370 cases of illicit trafficking. Information is also available on potential attempts of and actual acts of sabotage. For any State, the first step in ensuring the security of their materials is an effective national system. Such a system must contain multiple elements, including physical protection measures, material accountability arrangements, reliable detection capabilities, and plans for rapid and effective response when material is found to be lost, stolen or otherwise not under proper control. The system must also cover illegal waste dumping and other activities that would result in the release of radioactive material into the environment. All these measures should be based on well founded legal and regulatory structures. In many cases, the responsibility for these various elements lies with different bodies, and co-operation between them is vital to the success of the national system. The Agency's programme Security of Material aims at being of service to States in their efforts to upgrade their security

  12. Thermodynamics of nuclear materials

    International Nuclear Information System (INIS)

    1979-01-01

    Full text: The science of chemical thermodynamics has substantially contributed to the understanding of the many problems encountered in nuclear and reactor technology. These problems include reaction of materials with their surroundings and chemical and physical changes of fuels. Modern reactor technology, by its very nature, has offered new fields of investigations for the scientists and engineers concerned with the design of nuclear fuel elements. Moreover, thermodynamics has been vital in predicting the behaviour of new materials for fission as well as fusion reactors. In this regard, the Symposium was organized to provide a mechanism for review and discussion of recent thermodynamic investigations of nuclear materials. The Symposium was held in the Juelich Nuclear Research Centre, at the invitation of the Government of the Federal Republic of Germany. The International Atomic Energy Agency has given much attention to the thermodynamics of nuclear materials, as is evidenced by its sponsorship of four international symposia in 1962, 1965, 1967, and 1974. The first three meetings were primarily concerned with the fundamental thermodynamics of nuclear materials; as with the 1974 meeting, this last Symposium was primarily aimed at the thermodynamic behaviour of nuclear materials in actual practice, i.e., applied thermodynamics. Many advances have been made since the 1974 meeting, both in fundamental and applied thermodynamics of nuclear materials, and this meeting provided opportunities for an exchange of new information on this topic. The Symposium dealt in part with the thermodynamic analysis of nuclear materials under conditions of high temperatures and a severe radiation environment. Several sessions were devoted to the thermodynamic studies of nuclear fuels and fission and fusion reactor materials under adverse conditions. These papers and ensuing discussions provided a better understanding of the chemical behaviour of fuels and materials under these

  13. Materials at LANL

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, Antoinette J [Los Alamos National Laboratory

    2010-01-01

    Exploring the physics, chemistry, and metallurgy of materials has been a primary focus of Los Alamos National Laboratory since its inception. In the early 1940s, very little was known or understood about plutonium, uranium, or their alloys. In addition, several new ionic, polymeric, and energetic materials with unique properties were needed in the development of nuclear weapons. As the Laboratory has evolved, and as missions in threat reduction, defense, energy, and meeting other emerging national challenges have been added, the role of materials science has expanded with the need for continued improvement in our understanding of the structure and properties of materials and in our ability to synthesize and process materials with unique characteristics. Materials science and engineering continues to be central to this Laboratory's success, and the materials capability truly spans the entire laboratory - touching upon numerous divisions and directorates and estimated to include >1/3 of the lab's technical staff. In 2006, Los Alamos and LANS LLC began to redefine our future, building upon the laboratory's established strengths and promoted by strongly interdependent science, technology and engineering capabilities. Eight Grand Challenges for Science were set forth as a technical framework for bridging across capabilities. Two of these grand challenges, Fundamental Understanding of Materials and Superconductivity and Actinide Science. were clearly materials-centric and were led out of our organizations. The complexity of these scientific thrusts was fleshed out through workshops involving cross-disciplinary teams. These teams refined the grand challenge concepts into actionable descriptions to be used as guidance for decisions like our LDRD strategic investment strategies and as the organizing basis for our external review process. In 2008, the Laboratory published 'Building the Future of Los Alamos. The Premier National Security Science Laboratory

  14. Radioactive waste solidifying material

    International Nuclear Information System (INIS)

    Ono, Keiichi; Sakai, Etsuro.

    1989-01-01

    The solidifying material according to this invention comprises cement material, superfine powder, highly water reducing agent, Al-containing rapid curing material and coagulation controller. As the cement material, various kinds of quickly hardening, super quickly hardening and white portland cement, etc. are usually used. As the superfine powder, those having average grain size smaller by one order than that of the cement material are desirable and silica dusts, etc. by-produced upon preparing silicon, etc. are used. As the highly water reducing agent, surface active agents of high decomposing performance and comprising naphthalene sulfonate, etc. as the main ingredient are used. As the Al-containing rapidly curing material, calcium aluminate, etc. is used in an amount of less than 10 parts by weight based on 100 parts by weight of the powdery body. As the coagulation controller, boric acid etc. usually employed as a retarder is used. This can prevent dissolution or collaption of pellets and reduce the leaching of radioactive material. (T.M.)

  15. NSUF Irradiated Materials Library

    Energy Technology Data Exchange (ETDEWEB)

    Cole, James Irvin [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-09-01

    The Nuclear Science User Facilities has been in the process of establishing an innovative Irradiated Materials Library concept for maximizing the value of previous and on-going materials and nuclear fuels irradiation test campaigns, including utilization of real-world components retrieved from current and decommissioned reactors. When the ATR national scientific user facility was established in 2007 one of the goals of the program was to establish a library of irradiated samples for users to access and conduct research through competitively reviewed proposal process. As part of the initial effort, staff at the user facility identified legacy materials from previous programs that are still being stored in laboratories and hot-cell facilities at the INL. In addition other materials of interest were identified that are being stored outside the INL that the current owners have volunteered to enter into the library. Finally, over the course of the last several years, the ATR NSUF has irradiated more than 3500 specimens as part of NSUF competitively awarded research projects. The Logistics of managing this large inventory of highly radioactive poses unique challenges. This document will describe materials in the library, outline the policy for accessing these materials and put forth a strategy for making new additions to the library as well as establishing guidelines for minimum pedigree needed to be included in the library to limit the amount of material stored indefinitely without identified value.

  16. Hydrophilic nanoporous materials

    DEFF Research Database (Denmark)

    2010-01-01

    The present application discloses a method for preparing and rendering hydrophilic a nanoporous material of a polymer matrix which has a porosity of 0.1-90 percent (v/v), such that the ratio between the final water absorption (percent (w/w)) and the porosity (percent (v/v)) is at least 0.05, the ......The present application discloses a method for preparing and rendering hydrophilic a nanoporous material of a polymer matrix which has a porosity of 0.1-90 percent (v/v), such that the ratio between the final water absorption (percent (w/w)) and the porosity (percent (v/v)) is at least 0.......05, the method comprising the steps of: (a) preparing a precursor material comprising at least one polymeric component and having a first phase and a second phase; (b) removal of at least a part of the first phase of the precursor material prepared in step (a) so as to leave behind a nanoporous material...... of the polymer matrix; (c) irradiating at least a part of said nanoporous material with light of a wave length of in the range of 250-400 nm (or 200-700 nm) in the presence of oxygen and/or ozone. Corresponding hydrophilic nanoporous materials are also disclosed. L...

  17. Safeguards for special nuclear materials

    International Nuclear Information System (INIS)

    Carlson, R.L.

    1979-12-01

    Safeguards, accountability, and nuclear materials are defined. The accuracy of measuring nuclear materials is discussed. The use of computers in nuclear materials accounting is described. Measures taken to physically protect nuclear materials are described

  18. Professional Nuclear Materials Management

    International Nuclear Information System (INIS)

    Forcella, A.A.; O'Leary, W.J.

    1966-01-01

    This paper describes the scope of nuclear materials management for a typical power reactor in the United States of America. Since this power reactor is financed by private capital, one of the principal obligations of the reactor operator is to ensure that the investment is protected and will furnish an adequate financial return. Because of the high intrinsic value of nuclear materials, appropriate security and accountability must be continually exercised to minimize losses beyond security and accountability for the nuclear materials. Intelligent forethought and planning must be employed to ensure that additional capital is not lost as avoidable additional costs or loss of revenue in a number of areas. The nuclear materials manager must therefore provide in advance against the following contingencies and maintain constant control or liaison against deviations from planning during (a) pre-reactor acquisition of fuel and fuel elements, (b) in-reactor utilization of the fuel elements, and (c) post-reactor recovery of fuel values. During pre-reactor planning and operations, it is important that the fuel element be designed for economy in manufacture, handling, shipping, and replaceability. The time schedule for manufacturing operations must minimize losses of revenue from unproductive dead storage of high cost materials. For in-reactor operations, the maximum achievable burn-up of the fissionable material must be obtained by means of appropriate fuel rearrangement schemes. Concurrently the unproductive down-time of the reactor for fuel rearrangement, inspections, and the like must be minimized. In the post-reactor period, when the fuel has reached a predetermined depletion of fissionable material, the nuclear materials manager must provide for the most economical reprocessing and recovery of fissionable values and by-products. Nuclear materials management is consequently an essential factor in achieving competitive fuel cycle and unit energy costs with power reactors

  19. High temperature materials

    International Nuclear Information System (INIS)

    2003-01-01

    The aim of this workshop is to share the needs of high temperature and nuclear fuel materials for future nuclear systems, to take stock of the status of researches in this domain and to propose some cooperation works between the different research organisations. The future nuclear systems are the very high temperature (850 to 1200 deg. C) gas cooled reactors (GCR) and the molten salt reactors (MSR). These systems include not only the reactor but also the fabrication and reprocessing of the spent fuel. This document brings together the transparencies of 13 communications among the 25 given at the workshop: 1) characteristics and needs of future systems: specifications, materials and fuel needs for fast spectrum GCR and very high temperature GCR; 2) high temperature materials out of neutron flux: thermal barriers: materials, resistance, lifetimes; nickel-base metal alloys: status of knowledge, mechanical behaviour, possible applications; corrosion linked with the gas coolant: knowledge and problems to be solved; super-alloys for turbines: alloys for blades and discs; corrosion linked with MSR: knowledge and problems to be solved; 3) materials for reactor core structure: nuclear graphite and carbon; fuel assembly structure materials of the GCR with fast neutron spectrum: status of knowledge and ceramics and cermets needs; silicon carbide as fuel confinement material, study of irradiation induced defects; migration of fission products, I and Cs in SiC; 4) materials for hydrogen production: status of the knowledge and needs for the thermochemical cycle; 5) technologies: GCR components and the associated material needs: compact exchangers, pumps, turbines; MSR components: valves, exchangers, pumps. (J.S.)

  20. Thermal fatigue. Materials modelling

    International Nuclear Information System (INIS)

    Siegele, D.; Fingerhuth, J.; Mrovec, M.

    2012-01-01

    In the framework of the ongoing joint research project 'Thermal Fatigue - Basics of the system-, outflow- and material-characteristics of piping under thermal fatigue' funded by the German Federal Ministry of Education and Research (BMBF) fundamental numerical and experimental investigations on the material behavior under transient thermal-mechanical stress conditions (high cycle fatigue V HCF and low cycle fatigue - LCF) are carried out. The primary objective of the research is the further development of simulation methods applied in safety evaluations of nuclear power plant components. In this context the modeling of crack initiation and growth inside the material structure induced by varying thermal loads are of particular interest. Therefore, three scientific working groups organized in three sub-projects of the joint research project are dealing with numerical modeling and simulation at different levels ranging from atomistic to micromechanics and continuum mechanics, and in addition corresponding experimental data for the validation of the numerical results and identification of the parameters of the associated material models are provided. The present contribution is focused on the development and experimental validation of material models and methods to characterize the damage evolution and the life cycle assessment as a result of thermal cyclic loading. The individual purposes of the subprojects are as following: - Material characterization, Influence of temperature and surface roughness on fatigue endurances, biaxial thermo-mechanical behavior, experiments on structural behavior of cruciform specimens and scatter band analysis (IfW Darmstadt) - Life cycle assessment with micromechanical material models (MPA Stuttgart) - Life cycle assessment with atomistic and damage-mechanical material models associated with material tests under thermal fatigue (Fraunhofer IWM, Freiburg) - Simulation of fatigue crack growth, opening and closure of a short crack under

  1. Photopolymer holographic recording material

    Science.gov (United States)

    Lawrence, J. R.; O'Neill, F. T.; Sheridan, J. T.

    Photopolymers are promising materials for use in holography. They have many advantages, such as ease of preparation, and are capable of efficiencies of up to 100%. A disadvantage of these materials is their inability to record high spatial frequency gratings when compared to other materials such as dichromated gelatin and silver halide photographic emulsion. Until recently, the drop off at high spatial frequencies of the material response was not predicted by any of the diffusion based models available. It has recently been proposed that this effect is due to polymer chains growing away from their initiation point and causing a smeared profile to be recorded. This is termed a non-local material response. Simple analytic expressions have been derived using this model and fits to experimental data have allowed values to be estimated for material parameters such as the diffusion coefficient of monomer, the ratio of polymerisation rate to diffusion rate and the distance that the polymer chains spread during holographic recording. The model predicts that the spatial frequency response might be improved by decreasing the mean polymer chain lengths and/or by increasing the mobility of the molecules used in the material. The experimental work carried out to investigate these predictions is reported here. This work involved (a) the changing of the molecular weights of chemical components within the material (dyes and binders) and (b) the addition of a chemical retarder in order to shorten the polymer chains, thereby decreasing the extent of the non-local effect. Although no significant improvement in spatial frequency response was observed the model appears to offer an improved understanding of the operation of the material.

  2. Material control evaluation

    International Nuclear Information System (INIS)

    Waddoups, I.G.; Anspach, D.A.; Abbott, J.A.

    1993-01-01

    Changes in the Department of Energy's (DOE) scope of work have stimulated several laboratories and commercial companies to develop and apply technology to enhance nuclear material control. Accountability, inventory, radiation exposure, and insider protection concerns increase as many DOE facilities require increased storage. This paper summarizes a study of the existing material control technologies. The goal of the study is to identify, characterize, and quantify the trade-offs associated with using these technologies to provide real-time information on stored nuclear material that in turn supports decreasing the frequency of inventories conducted by site personnel

  3. Fusion Reactor Materials

    International Nuclear Information System (INIS)

    Decreton, M.

    2000-01-01

    SCK-CEN's research and development programme on fusion reactor materials includes: (1) the study of the mechanical behaviour of structural materials under neutron irradiation (including steels, inconel, molybdenum, chromium); (2) the determination and modelling of the characteristics of irradiated first wall materials such as beryllium; (3) the detection of abrupt electrical degradation of insulating ceramics under high temperature and neutron irradiation; (4) the study of the dismantling and waste disposal strategy for fusion reactors.; (5) a feasibility study for the testing of blanket modules under neutron radiation. Main achievements in these topical areas in the year 1999 are summarised

  4. Hydrogen bonded supramolecular materials

    CERN Document Server

    Li, Zhan-Ting

    2015-01-01

    This book is an up-to-date text covering topics in utilizing hydrogen bonding for constructing functional architectures and supramolecular materials. The first chapter addresses the control of photo-induced electron and energy transfer. The second chapter summarizes the formation of nano-porous materials. The following two chapters introduce self-assembled gels, many of which exhibit unique functions. Other chapters cover the advances in supramolecular liquid crystals and the versatility of hydrogen bonding in tuning/improving the properties and performance of materials. This book is designed

  5. Reliability of construction materials

    International Nuclear Information System (INIS)

    Merz, H.

    1976-01-01

    One can also speak of reliability with respect to materials. While for reliability of components the MTBF (mean time between failures) is regarded as the main criterium, this is replaced with regard to materials by possible failure mechanisms like physical/chemical reaction mechanisms, disturbances of physical or chemical equilibrium, or other interactions or changes of system. The main tasks of the reliability analysis of materials therefore is the prediction of the various failure reasons, the identification of interactions, and the development of nondestructive testing methods. (RW) [de

  6. Electro photographic materials

    International Nuclear Information System (INIS)

    Buzdugan, A.; Andries, A.; Iovu, M.

    2000-01-01

    The invention relates to the creation of electro photographic materials . The invention allows to extend the material photosensitivity into the infrared range of the spectrum. An electro photographic materials contains an electro conducting base, including a dielectric base 1, for example glass, an electro conducting layer 2, for example of Al, Ni, Cr, an injecting layer 3, consisting of amorphous indium phosphide, a vitreous layer 4 of the arsenic sulphide - antimony sulphide system and a transporting layer 5 of the arsenic sulphide or arsenic selenide

  7. 'Material unaccounted for' (MUF)

    International Nuclear Information System (INIS)

    1977-01-01

    MUF is an item of importance in materials accounting measures now embodied in international safeguard arrangements, and in recent public debates requests have been made that the figures for MUF appearing in the Atomic Energy Authority and British Nuclear Fuels Ltd. records should be published. Joint statements issued by the UKAEA and BNFL in July 1977 are here published. These statements describe the procedures for nuclear materials accounting at AEA and BNFL sites and the nature of the inventory differences (MUF) that arise in all nuclear materials accounting operations. Figures for highly enriched U and Pu are included. (U.K.)

  8. RADIOACTIVE MATERIALS SENSORS

    International Nuclear Information System (INIS)

    Mayo, Robert M.; Stephens, Daniel L.

    2009-01-01

    Providing technical means to detect, prevent, and reverse the threat of potential illicit use of radiological or nuclear materials is among the greatest challenges facing contemporary science and technology. In this short article, we provide brief description and overview of the state-of-the-art in sensor development for the detection of radioactive materials, as well as an identification of the technical needs and challenges faced by the detection community. We begin with a discussion of gamma-ray and neutron detectors and spectrometers, followed by a description of imaging sensors, active interrogation, and materials development, before closing with a brief discussion of the unique challenges posed in fielding sensor systems.

  9. Treating carbonaceous materials

    Energy Technology Data Exchange (ETDEWEB)

    Pier, M

    1929-08-26

    To separate the constituents or conversion products, which are liquid or which liquefy when heated, from solid distillable carbonaceous materials such as coals, oil shales, or other bituminous substances, the initial materials are subjected to a destructive hydrogenation under mild conditions so that the formation of benzines is substantially avoided, after which the material is subjected to an extraction treatment with solvents. The constituents of high boiling point range, suitable for the production of lubricating oils and solid paraffins, obtained by the said destructive hydrogenation are separated off before or/and after the said extraction treatment.

  10. Mechanics of soft materials

    CERN Document Server

    Volokh, Konstantin

    2016-01-01

    This book provides a concise introduction to soft matter modelling. It offers an up-to-date review of continuum mechanical description of soft and biological materials from the basics to the latest scientific materials. It includes multi-physics descriptions, such as chemo-, thermo-, electro- mechanical coupling. It derives from a graduate course at Technion that has been established in recent years. It presents original explanations for some standard materials and features elaborated examples on all topics throughout the text. PowerPoint lecture notes can be provided to instructors. .

  11. Electrically conductive composite material

    Science.gov (United States)

    Clough, Roger L.; Sylwester, Alan P.

    1989-01-01

    An electrically conductive composite material is disclosed which comprises a conductive open-celled, low density, microcellular carbon foam filled with a non-conductive polymer or resin. The composite material is prepared in a two-step process consisting of first preparing the microcellular carbon foam from a carbonizable polymer or copolymer using a phase separation process, then filling the carbon foam with the desired non-conductive polymer or resin. The electrically conductive composites of the present invention has a uniform and consistant pattern of filler distribution, and as a result is superior over prior art materials when used in battery components, electrodes, and the like.

  12. Fusion Reactor Materials

    Energy Technology Data Exchange (ETDEWEB)

    Decreton, M

    2000-07-01

    SCK-CEN's research and development programme on fusion reactor materials includes: (1) the study of the mechanical behaviour of structural materials under neutron irradiation (including steels, inconel, molybdenum, chromium); (2) the determination and modelling of the characteristics of irradiated first wall materials such as beryllium; (3) the detection of abrupt electrical degradation of insulating ceramics under high temperature and neutron irradiation; (4) the study of the dismantling and waste disposal strategy for fusion reactors.; (5) a feasibility study for the testing of blanket modules under neutron radiation. Main achievements in these topical areas in the year 1999 are summarised.

  13. Multifunctional materials and modeling

    CERN Document Server

    Korepanov, M A; Zaikov, Gennady E; Haghi, A K

    2015-01-01

    This important book presents a valuable collection of new research and new trends in nanomaterials, mesoscopy, quantum chemistry, and chemical physics processes. It highlights the development of nanomaterials as well as investigation of combustion and explosion processes. It highlights new trends in processes and methods of the treatment of polymeric materials and also covers material modification, including super small quantities of metal/carbon nanocomposites as well as new information on the modeling of processes and quantum calculations. Nonlinear kinetic appearances and their applications are highlighted as well. The chapters are divided into three major sections: computational modeling, surface and interface investigations, and nanochemistry, nanomaterials, and nanostructured materials.

  14. Materials science symposium 'materials science using accelerators'

    International Nuclear Information System (INIS)

    Ishii, Tetsuro; Asai, Masato; Chimi, Yasuhiro

    2005-07-01

    The facility of the JAERI-Tokai tandem accelerator and its booster has been contributing to advancing heavy-ion sciences in the fields of nuclear physics, nuclear chemistry, atomic and solid-state physics and materials science, taking advantage of its prominent performance of heavy-ion acceleration. This facility was recently upgraded by changing the acceleration tubes and installing an ECR ion-source at the terminal. The radioactive nuclear beam facility (Tokai Radioactive Ion Accelerator Complex, TRIAC) was also installed by the JAERI-KEK joint project. On this occasion, this meeting was held in order to provide a new step for the advancement of heavy-ion science, and to exchange information on recent activities and future plans using the tandem facility as well as on promising new experimental techniques. This meeting was held at Tokai site of JAERI on January 6th and 7th in 2005, having 24 oral presentations, and was successfully carried out with as many as 90 participants and lively discussions among scientists from all the fields of heavy-ion science, including solid-sate physics, nuclear physics and chemistry, and accelerator physics. This summary is the proceedings of this meeting. We would like to thank all the staffs of the accelerators section, participants and office workers in the Department of Materials Science for their support. The 24 of the presented papers are indexed individually. (J.P.N.)

  15. Phase-change materials handbook

    Science.gov (United States)

    Hale, D. V.; Hoover, M. J.; Oneill, M. J.

    1972-01-01

    Handbook describes relationship between phase-change materials and more conventional thermal control techniques and discusses materials' space and terrestrial applications. Material properties of most promising phase-change materials and purposes and uses of metallic filler materials in phase-change material composites are provided.

  16. Bureaucratic Politics and the Spoiled F-16 Sale to Indonesia

    National Research Council Canada - National Science Library

    1998-01-01

    .... foreign military sales policy. Despite efforts spearheaded by the United States Air Force and the State Departinent to see the deal through, the Clinton Administration wrthdrew its support to broker...

  17. Phytoremediation Potential of Plants Grown on Reclaimed Spoil Lands

    African Journals Online (AJOL)

    Post-mining reclamation is aimed at restoring the productive capacity of the disturbed land and ensuring socio-economic and environmental sustainability. Methods that have been employed for the reclamation activity are reported in the literature. This paper studied the utility of certain plant species in Ghana for remediating ...

  18. 'LITTLE FOXES THAT SPOIL THE VINE'* Abstract The article ...

    African Journals Online (AJOL)

    Fr. Ikenga

    Outside the constitutional exceptions, it is not only unlawful but morally despicable for anyone to kill another. It is this attitude that has provoked the debates on issues like ... See also Terrence Williams, Safeguarding the ..... military officers who attacked protesting residents who had gone to the premises of an oil company to.

  19. Preschoolers who refuse to be examined. Fearful or spoiled?

    Science.gov (United States)

    Schmitt, B D

    1984-05-01

    Twenty-two children (aged 2 to 5 years) who cried excessively or resisted physical examination during routine office visits initially seemed to be afraid of physicians, but eight were afraid of medical procedures, five had prolonged separation anxiety, six were manipulative, and three were afraid of men because of previous physical abuse by their fathers. Management plans were initiated for each etiological subtype. Five of eight parents whose children were afraid of medical procedures and five of six parents whose children were manipulative returned for counseling. In these cases, 100% (8/8) and 80% (4/5) of the children, respectively, made major improvement. Abused children required referral to mental health centers. Most parents of children with prolonged separation anxiety (three of five) did not consider the overdependent behavior to be a problem and therefore did not comply with treatment recommendations.

  20. Spoiled or Spectacular? A Look at the Only Child.

    Science.gov (United States)

    Rivera, Maida; Carrasquillo, Jeanette

    The only child has traditionally been thought to lack appropriate social skills, self-esteem, or friends. Recent research, as summarized in this paper, contradicts these popular beliefs. In level of achievement and intelligence, only-children appear to have an advantage over children with siblings; research on their sociability and self-esteem has…