Future energy and emissions policy scenarios in Ireland for private car transport

International Nuclear Information System (INIS)

Daly, Hannah E.; Ó Gallachóir, Brian P.

2012-01-01

In this paper we use a technological model of Ireland's future car stock to simulate the impact of a range of policy measures on the baseline trend in energy demand in the period to 2030. The policies and measures modelled comprise meeting deployment targets for electric vehicles and compressed natural gas vehicles, an EU regulation for the improvement of vehicle efficiency, implementation of a national biofuel obligation, as well as several behavioural measures (encouraging modal shifting and reduced travel demand). The impact of the different measures simulated is measured in terms of their contribution to meeting Ireland's ambitious targets for energy savings, for renewable energy penetration and for greenhouse gas (GHG) emissions reductions. The results point to a possible improvement of 32% in car stock efficiency, the achievement of 7.8% renewable energy share of road and rail transport and a 22% reduction in non-ETS private car CO 2 emissions relative to 2009 levels. A scenario analysis on meeting the EV penetration target shows a significant range of CO 2 emissions reductions depending on the cars (and mileage) displaced and on the electricity generation portfolio. - Highlights: ► Private car policy scenarios for Ireland modelled. ► Impact of vehicle efficiency, fuel switching and behavioural measures evaluated. ► Highlights distance to EU non-ETS emissions and renewable energy targets. ► Analysis of EV target shows that GHG mitigation potential is very sensitive.

Fiscal Measures to Reduce CO2 Emissions from New Passenger Cars

OpenAIRE

Cowi A/S

2002-01-01

Model based calculations constitute the core output of this study. The calculations assess the extent to which vehicle related taxes (mainly acquisition taxes and ownership taxes) can be effective means to reduce CO2 emissions from new cars. More specifically, the model calculations have assessed the ability of vehicle taxes to support the target to reduce average CO2 emissions from new cars down to a level of 120 g/km. This is the agreed target of the Community Strategy to reduce CO2 emissio...

Stricter antitrust legislation?; Verschaerfung des Kartellrechts?

Energy Technology Data Exchange (ETDEWEB)

Heller, W.

2007-01-15

In November 2006, the German Federal Ministry of Economics sent a ministerial draft bill on combating price abuses in the energy supply and food trade sectors to the trade associations for comment. The bill must be seen as part of a set of measures of the federal government seeking to improve conditions for more competition in the energy sector. An omnibus law is to add a new Section 29 to the Act against Restrictions on Competition (Antitrust Act). The addition is to bear the heading of 'Power Economy' and has been designed to prevent a utility (vendor of electricity, gas, and district heat) from abusing its position on a market which it dominates either alone or together with other utility companies. Depending on the interests involved, comments on the draft bills differ. On the whole, this tightening up of antitrust legislation is preceived more as a repair job. Stricter antitrust provisions absolutely must also be seen in their European dimension. European firms not falling under this stricter antitrust law enjoy advantages over German firms. (orig.)

Recent evidence concerning higher NO x emissions from passenger cars and light duty vehicles

Science.gov (United States)

Carslaw, David C.; Beevers, Sean D.; Tate, James E.; Westmoreland, Emily J.; Williams, Martin L.

2011-12-01

Ambient trends in nitrogen oxides (NO x) and nitrogen dioxide (NO 2) for many air pollution monitoring sites in European cities have stabilised in recent years. The lack of a decrease in the concentration of NO x and in particular NO 2 is of concern given European air quality standards are set in law. The lack of decrease in the concentration of NO x and NO 2 is also in clear disagreement with emission inventory estimates and projections. This work undertakes a comprehensive analysis of recent vehicle emissions remote sensing data from seven urban locations across the UK. The large sample size of 84,269 vehicles was carefully cross-referenced to a detailed and comprehensive database of vehicle information. We find that there are significant discrepancies between current UK/European estimates of NO x emissions and those derived from the remote sensing data for several important classes of vehicle. In the case of light duty diesel vehicles it is found that NO x emissions have changed little over 20 years or so over a period when the proportion of directly emitted NO 2 has increased substantially. For diesel cars it is found that absolute emissions of NO x are higher across all legislative classes than suggested by UK and other European emission inventories. Moreover, the analysis shows that more recent technology diesel cars (Euro 3-5) have clear increasing NO x emissions as a function of Vehicle Specific Power, which is absent for older technology vehicles. Under higher engine loads, these newer model diesel cars have a NO x/CO 2 ratio twice that of older model cars, which may be related to the increased use of turbo-charging. Current emissions of NO x from early technology catalyst-equipped petrol cars (Euro 1/2) were also found to be higher than emission inventory estimates - and comparable with NO x emissions from diesel cars. For heavy duty vehicles, it is found that NO x emissions were relatively stable until the introduction of Euro IV technology when

The impact of reducing car weight on global emissions: the future fleet in Great Britain

Science.gov (United States)

Serrenho, André Cabrera; Norman, Jonathan B.; Allwood, Julian M.

2017-05-01

Current European policies define targets for future direct emissions of new car sales that foster a fast transition to electric drivetrain technologies. However, these targets do not consider the emissions produced in electricity generation and material production, and therefore fail to incentivise car manufacturers to consider the benefits of vehicle weight reduction. In this paper, we examine the potential benefits of limiting the average weight and altering the material composition of new cars in terms of global greenhouse gas emissions produced during the use phase, electricity generation and material production. We anticipate the emissions savings for the future car fleet in Great Britain until 2050 for various alternative futures, using a dynamic material flow analysis of ferrous metals and aluminium, and considering an evolving demand for car use. The results suggest that fostering vehicle weight reduction could produce greater cumulative emissions savings by 2050 than those obtained by incentivising a fast transition to electric drivetrains, unless there is an extreme decarbonization of the electricity grid. Savings promoted by weight reduction are immediate and do not depend on the pace of decarbonization of the electricity grid. Weight reduction may produce the greatest savings when mild steel in the car body is replaced with high-strength steel. This article is part of the themed issue 'Material demand reduction'.

Policy options to reduce passenger car CO2 emissions after 2020

Energy Technology Data Exchange (ETDEWEB)

De Wilde, H.P.J.; Kroon, P. [ECN Beleidsstudies, Petten (Netherlands)

2013-02-15

The EU has set emission targets for new cars up to 2020 and is now preparing the post 2020 legislation. The present study aims to give insight in the design of policies to further reduce passenger car emissions after 2020. Internal combustion engine (ICE) vehicles are now expected to enable deeper and less costly CO2 emission reductions than envisioned until recently. However, even advanced ICE vehicles will not enable to meet the very stringent long term emission reduction targets for passenger cars. Therefore transport policies need not only to reduce emissions of ICE vehicles, but also ensure that electric and hydrogen vehicles are phased in timely, along with low-CO2 electricity and hydrogen. Current legislation to regulate tank-to-wheel vehicle emissions is based on CO2-limits, expressed in g CO2/km. On the short term it is important to maximize the efficiency of conventional vehicles. At the same time it is essential to foster the market introduction of electric and hydrogen vehicles, given their potential to reach eventually much deeper overall CO2-reductions. When the market share of electric and hydrogen vehicles grows it becomes increasingly important to maximize their efficiency and to minimize their upstream CO2 emissions. Maximizing both efficiency and overall CO2-performance of all vehicle types - ICE, electric, and hydrogen - will be complicated to achieve with a single CO2-based standard. At this point an efficiency-based standard is more effective, and may offer some additional benefits too. The current report provides basic directions of how such legislation could be shaped.

Sorting on the Used-Car Market After the Volkswagen Emission Scandal

OpenAIRE

Strittmatter, Anthony; Lechner, Michael

2017-01-01

The disclosure of the VW emission manipulation scandal caused a quasi-experimental market shock in the observable quality of VW diesel vehicles. We consider a classical model for adverse selection and sorting to derive an empirically testable hypothesis about the impact of observable quality on the supply of used cars. We test the hypothesis with data collected from an online car selling platform which reflects about 50% of the German used-car market. The empirical approach is based on a cond...

Diesel passenger car PM emissions: From Euro 1 to Euro 4 with particle filter

Science.gov (United States)

Tzamkiozis, Theodoros; Ntziachristos, Leonidas; Samaras, Zissis

2010-03-01

This paper examines the impact of the emission control and fuel technology development on the emissions of gaseous and, in particular, PM pollutants from diesel passenger cars. Three cars in five configurations in total were measured, and covered the range from Euro 1 to Euro 4 standards. The emission control ranged from no aftertreatment in the Euro 1 case, an oxidation catalyst in Euro 2, two oxidation catalysts and exhaust gas recirculation in Euro 3 and Euro 4, while a catalyzed diesel particle filter (DPF) fitted in the Euro 4 car led to a Euro 4 + DPF configuration. Both certification test and real-world driving cycles were employed. The results showed that CO and HC emissions were much lower than the emission standard over the hot-start real-world cycles. However, vehicle technologies from Euro 2 to Euro 4 exceeded the NOx and PM emission levels over at least one real-world cycle. The NOx emission level reached up to 3.6 times the certification level in case of the Euro 4 car. PM were up to 40% and 60% higher than certification level for the Euro 2 and Euro 3 cars, while the Euro 4 car emitted close or slightly below the certification level over the real-world driving cycles. PM mass reductions from Euro 1 to Euro 4 were associated with a relevant decrease in the total particle number, in particular over the certification test. This was not followed by a respective reduction in the solid particle number which remained rather constant between the four technologies at 0.86 × 10 14 km -1 (coefficient of variation 9%). As a result, the ratio of solid vs. total particle number ranged from ˜50% in Euro 1-100% in Euro 4. A significant reduction of more than three orders of magnitude in solid particle number is achieved with the introduction of the DPF. However, the potential for nucleation mode formation at high speed from the DPF car is an issue that needs to be considered in the over all assessment of its environmental benefit. Finally, comparison of the

Decomposition of factors determining the trend of CO{sub 2} emissions from car travel in Great Britain (1970-2000)

Energy Technology Data Exchange (ETDEWEB)

Kwon, Tae-Hyeong [The Korea Transport Institute (KOTI), 2311 Daehwa-dong, Ilsan-gu, Goyang-Shi, Gyeonggi-do, 411-701 (Korea, Republic of)

2005-04-15

Carbon dioxide (CO{sub 2}) is the most important of the greenhouse gases that are causing global warming. The transport sector currently accounts for more than one-quarter of CO{sub 2} emissions and more importantly its share in total emissions is increasing in most countries. This paper investigates the key factors in the change in CO{sub 2} emissions from car travel in Great Britain over the last 30 years. It attempts to disentangle determinants of growth in CO{sub 2} emissions from car travel, which has the largest share of emissions in road transport. The study is based on various decomposition analyses, starting from the IPAT identity. As summarised in the IPAT identity, the degree of the Impact of human activity on the environment is determined by changes in Population, Affluence (per-capita consumption) and Technology (environmental impact per quantity of consumption). In the case of CO{sub 2} emissions from car travel in Great Britain, the affluence (A) factor (car driving distance per person) was a dominant force for the growth of emissions over the last 30 years. Not only do people travel longer distances by cars than 30 years ago, but car occupancy rates have also decreased, contributing to the growth of car driving distance per person. Although technology (T) factors such as fuel efficiency and fuel substitution to diesel fuel partly cancelled out these growth effects of affluence factors, this contribution was relatively small. However, in the 1990s there emerged a different pattern in the trend. Of the affluence (A) factors, the growth rate of car trip distance per person weakened considerably. As for the technology (T) effect, the carbon intensity of car driving kept decreasing over this period. Therefore, although CO{sub 2} emissions from car travel (I) continued to increase, the growth rate became substantially lower than in the earlier periods. More detailed investigation into the determinants of both affluence (A) factors and technology (T

Fiscal policy and CO2 emissions of new passenger cars in the EU

NARCIS (Netherlands)

Gerlagh, Reyer; Van Den Bijgaart, Inge; Nijland, Hans; Michielsen, Thomas

To what extent have national fiscal policies contributed to the decarbonisation of newly sold passenger cars? We construct a simple model that generates predictions regarding the effect of fiscal policies on average CO2 emissions of new cars, and then test the model empirically. Our empirical

Direct emission of nitrous acid (HONO) from gasoline cars in China determined by vehicle chassis dynamometer experiments

Science.gov (United States)

Liu, Yuhan; Lu, Keding; Ma, Yufang; Yang, Xinping; Zhang, Wenbin; Wu, Yusheng; Peng, Jianfei; Shuai, Shijin; Hu, Min; Zhang, Yuanhang

2017-11-01

HONO plays a key role in atmospheric chemistry, and while its importance is well-known, the sources of HONO are still not completely understood. As a component of ambient HONO sources, direct emission from vehicles is an area that should be extensively studied. In this study, we determined the HONO emission index for typical gasoline vehicles in the car population of China through a chassis dynamometer with different types of engines (PFI/GDI), starting conditions (cold/warm) and running styles (Beijing cycle). Emission ratios of HONO to nitrogen oxide (NOX) for the Chinese gasoline cars are determined to be in the range of (0.03-0.42) % and an averaged value is about 0.18%, which are comparable to those reported in the few studies available in Europe, the United States and Japan for gasoline cars while smaller for those of the diesel cars. The atmospheric impact of the direct HONO emission from gasoline cars was analyzed for a typical urban site in Beijing, significant contributions of the direct emission toward the HONO budget were found during morning rush hours or twilight conditions to be 8-12%.

Statistical Evaluation of the Emissions Level Of CO, CO2 and HC Generated by Passenger Cars

Directory of Open Access Journals (Sweden)

Claudiu Ursu

2014-12-01

Full Text Available This paper aims to make an evaluation of differences emission level of CO, CO2 and HC generated by passenger cars in different walking regimes and times, to identify measures of reducing pollution. Was analyzed a sample of Dacia Logan passenger cars (n = 515, made during the period 2004-2007, equipped with spark ignition engines, assigned to emission standards EURO 3 (E3 and EURO4 (E4. These cars were evaluated at periodical technical inspection (ITP by two times in the two walk regimes (slow idle and accelerated idle. Using the t test for paired samples (Paired Samples T Test, the results showed that there are significant differences between emissions levels (CO, CO2, HC generated by Dacia Logan passenger cars at both assessments, and regression analysis showed that these differences are not significantly influenced by turnover differences.

Co-benefits? Not always: Quantifying the negative effect of a CO2-reducing car taxation policy on NOx emissions

International Nuclear Information System (INIS)

Leinert, Stephan; Daly, Hannah; Hyde, Bernard; Gallachóir, Brian Ó

2013-01-01

With the current focus of policy action on climate change mitigation, it is important to investigate possible negative side effects of climate change policies on air pollutants. A 34% increase in CO 2 emissions from private cars in Ireland over the period 2000–2008 prompted a change in private car taxation in 2008 to incentivise the purchase of lower CO 2 emitting cars. The impact has been successful and the measure has accelerated the dieselisation of the car fleet. This however, raises an important question, namely how does the dieselisation of the car fleet affect NO x emissions? This paper combines two models to address this question, a car stock model to generate activity data (future composition and activity of Ireland's car stock) and the COPERT model to quantify the NO x emissions generated in the period 2008–2020. Previous analysis shows that the CO 2 taxation policy measure is anticipated to deliver a 7% reduction in private car related CO 2 emissions in 2020 compared with a baseline pre-tax scenario. The results here show that NO x emissions decrease in all scenarios, but a lesser degree of reduction is achieved due to dieselisation, with NO x emissions in the post-tax scenario 28% higher than the pre-tax scenario in 2020. - Highlights: • Irish car tax changed in 2008 to a CO 2 -graduated system. • Change successfully reduced the CO 2 intensity of new cars through dieselization. • However, this has negative consequences for air pollution. • Bottom-up model analyses pre-tax and post-tax NO x to 2020 using COPERT. • NO x projected to be 28% higher in 2020 compared with pre-tax scenario

Energy use, cost and CO2 emissions of electric cars

International Nuclear Information System (INIS)

van Vliet, Oscar; Brouwer, Anne Sjoerd; Kuramochi, Takeshi; van den Broek, Machteld; Faaij, Andre

2011-01-01

We examine efficiency, costs and greenhouse gas emissions of current and future electric cars (EV), including the impact from charging EV on electricity demand and infrastructure for generation and distribution. Uncoordinated charging would increase national peak load by 7% at 30% penetration rate of EV and household peak load by 54%, which may exceed the capacity of existing electricity distribution infrastructure. At 30% penetration of EV, off-peak charging would result in a 20% higher, more stable base load and no additional peak load at the national level and up to 7% higher peak load at the household level. Therefore, if off-peak charging is successfully introduced, electric driving need not require additional generation capacity, even in case of 100% switch to electric vehicles. GHG emissions from electric driving depend most on the fuel type (coal or natural gas) used in the generation of electricity for charging, and range between 0 g km -1 (using renewables) and 155 g km -1 (using electricity from an old coal-based plant). Based on the generation capacity projected for the Netherlands in 2015, electricity for EV charging would largely be generated using natural gas, emitting 35-77 g CO 2 eq km -1 . We find that total cost of ownership (TCO) of current EV are uncompetitive with regular cars and series hybrid cars by more than 800 EUR year -1 . TCO of future wheel motor PHEV may become competitive when batteries cost 400 EUR kWh -1 , even without tax incentives, as long as one battery pack can last for the lifespan of the vehicle. However, TCO of future battery powered cars is at least 25% higher than of series hybrid or regular cars. This cost gap remains unless cost of batteries drops to 150 EUR kWh -1 in the future. Variations in driving cost from charging patterns have negligible influence on TCO. GHG abatement costs using plug-in hybrid cars are currently 400-1400 EUR tonne -1 CO 2eq and may come down to -100 to 300 EUR tonne -1 . Abatement cost using

Energy use, cost and CO2 emissions of electric cars

NARCIS (Netherlands)

van Vliet, O.; Brouwer, A.S.; Kuramochi, T.; van den Broek, M.A.; Faaij, A.P.C.

2010-01-01

We examine efficiency, costs and greenhouse gas emissions of current and future electric cars (EV), including the impact from charging EV on electricity demand and infrastructure for generation and distribution. Uncoordinated charging would increase national peak load by 7% at 30% penetration rate

Reduction of CO/sub 2/ emissions through fuel economy standards for diesel cars in pakistan

International Nuclear Information System (INIS)

Memon, L.A.; Mehlia, T.M.I.; Hassan, M.H.

2007-01-01

In Pakistan, like many developing countries, the increasing prosperity and population growth are resulting in accelerated growth in vehicle population and vehicle kilometers traveled. This causes air pollution due to huge CO/sub 2/ emissions. Automobile fuel economy standards have proven to be one of the most effective tools to control oil demand thereby reducing the GHG (Green House Gas) emissions like CO/sub 2/, This study presents the investigation to apply fuel economy standards in Pakistan, in order to predict the potential reduction in CO/sub 2/ emissions and saving in fuel demand. The study is focused on only diesel cars and the data of diesel car owners for previous fifteen years is obtained from the related sources in Pakistan. A growth trend of diesel car owners was analyzed and the number of diesel car owners in future was predicted by applying database computer software. Calculations were made to study the effect of fuel economy standards in terms of saving in fuel demand and the reduction in CO/sub 2/ emissions. The results reveal the potential application of fuel economy standards and it was found that a cumulative amount of fuel 39266775 liters can be saved and CO/sub 2/ emissions can be reduced by 106021 tons at the end of 2011-2012, if fuel economy standards are implemented in 2008-2009. (author)

Influence of driving style on fuel consumption and Emissions in diesel-powered passenger car

OpenAIRE

Fonseca González, Natalia Elizabeth; Casanova Kindelán, Jesús; Espinosa Zapata, Felipe

2010-01-01

This paper presents the main results of a study on the influence of driving style on fuel consumption and pollutant emissions of diesel passenger car in urban traffic. Driving styles (eco, normal or aggressive) patterns were based on the “eco-driving” criteria. The methodology is based on on-board emission measurements in real urban traffic in the city of Madrid. Five diesel passenger cars, have been tested. Through a statistical analysis, a Dynamic Performance Index was defined for die...

Analysis of Passenger Car Emission Factors in RDE Tests

Directory of Open Access Journals (Sweden)

Pielecha Jacek

2016-01-01

Full Text Available The article presents a study on emission measurements in passenger cars in tests conducted under real traffic conditions – Real Driving Emissions using a Portable Emission Measurement System type of equipment. A special feature of the outlined RDE tests is that they were performed in Polish road conditions, and thus their parameters may differ from their counterparts adopted in most European Union countries. Based on the findings vehicle emission conformity factors were developed, characterized as the fractional increase (or decrease of traffic emissions during the homologation test or under normal operation conditions in relation to the emission limit standards (for chosen emission class of the vehicle. Conducted research and the calculated conformity factors allowed for the environmental impact assessment of the vehicles of various emission classes, while also allowing early actions to restrict the emissions of selected components in passenger vehicles. The methods and measures used can also be applied to other types of vehicles (e.g. heavy duty or off-road vehicles or vehicles powered by other fuels.

Energy demand and greenhouse gas emissions during the production of a passenger car in China

International Nuclear Information System (INIS)

Yan Xiaoyu

2009-01-01

Rapidly-rising oil demand and associated greenhouse gas (GHG) emissions from road vehicles in China, passenger cars in particular, have attracted worldwide attention. As most studies to date were focused on the vehicle operation stage, the present study attempts to evaluate the energy demand and GHG emissions during the vehicle production process, which usually consists of two major stages-material production and vehicle assembly. Energy demand and GHG emissions in the material production stage are estimated using the following data: the mass of the vehicle, the distribution of material used by mass, and energy demand and GHG emissions associated with the production of each material. Energy demand in the vehicle assembly stage is estimated as a linear function of the vehicle mass, while the associated GHG emission is estimated according to the primary energy sources. It is concluded that the primary energy demand, petroleum demand and GHG emissions during the production of a medium-sized passenger car in China are 69,108 MJ, 14,545 MJ and 6575 kg carbon dioxide equivalent (CO 2 -eq). Primary energy demand, petroleum demand and GHG emissions in China's passenger car fleets in 2005 would be increased by 22%, 5% and 30%, respectively, if the vehicle production stage were included.

Analysis and modelling of the pollutant emissions from European cars regarding the driving characteristics and test cycles

Science.gov (United States)

André, Michel; Rapone, Mario

Within the European research project ARTEMIS, significant works have been conducted to analyse the hot emissions of pollutant from the passenger cars regarding the driving cycles and to propose modelling approaches taking into account large but heterogeneous datasets recorded in Europe. The review and analysis of a large range of test cycles enabled first the building-up of a set of contrasted cycles specifically designed for characterizing the influence of the driving conditions. These cycles were used for the measurement of the pollutants emission rates from nine passenger cars on a chassis dynamometer. Emissions measured on 30 vehicles tested on cycles adapted to their motorization (i.e., cycles for high- or low-powered cars, inducing thus a significant difference in the dynamic) were also considered for analysing the influence of the cycles and of the kinematic parameters on the hot emission rates of the regulated pollutants (CO, HC, NO x, CO 2, PM). An analyses of variance demonstrated the preponderance of the driving type (urban, rural road, motorway), of the vehicle category (fuel, emission standard) and emitting status (high/normal emitter) and thus the pertinence of analysing and modelling separately the corresponding emissions. It also demonstrated that Urban driving led systematically to high diesel emission rates and to high CO 2, HC and NO x emissions from petrol cars. Congested driving implied high CO 2 (diesel and petrol) and high diesel NO x emission. On motorway, the very high speeds generated high CO 2, while unsteady speeds induced diesel NO x and petrol CO over-emissions. A search for pertinent kinematic parameters showed that urban diesel emissions were mostly sensitive to stops and speed parameters, while petrol emissions were rather sensitive to acceleration parameters. On the motorway, diesel NO x and CO 2 emissions rates increased with the speed variability and occurrence of high speeds, while CO 2 and CO over-emission from petrol cars were

A comparative study of the elemental composition of the exhaust emissions of cars powered by liquefied petroleum gas and unleaded petrol

Science.gov (United States)

Lim, McKenzie C. H.; Ayoko, Godwin A.; Morawska, Lidia; Ristovski, Zoran D.; Jayaratne, E. Rohan; Kokot, Serge

Elements emitted from the exhausts of new Ford Falcon Forte cars powered by unleaded petrol (ULP) and liquefied petroleum gas (LPG) were measured on a chassis dynamometer. The measurements were carried out in February, June and August 2001, and at two steady state driving conditions (60 and 80 km h -1). Thirty seven elements were quantified in the exhaust samples by inductively coupled plasma mass spectrometry (ICPMS). The total emission factors of the elements from the exhausts of ULP cars were higher than those of LPG cars at both engine speeds even though high variability in the exhaust emissions from different cars was noted. The effect of the operating conditions such as mileage of the cars, engine speed, fuel and lubricating oil compositions on the emissions was studied. To investigate the effects of these conditions, multivariate data analysis methods were employed including exploratory principal component analysis (PCA), and the multi-criteria decision making methods (MCDM), preference ranking organization method for enrichment evaluation (PROMETHEE) and geometrical analysis for interactive aid (GAIA), for ranking the cars on the basis of the emission factors of the elements. PCA biplot of the complete data matrix showed a clear discrimination of the February, June and August emission test results. In addition, (i) platinum group elements (PGE) emissions were separated from each other in the three different clusters viz. Pt with February, Pd with June and Rh with August; (ii) the motor oil related elements, Zn and P, were particularly associated with the June and August tests (these vectors were also grouped with V, Al and Cu); and (iii) highest emissions of most major elements were associated with the August test after the cars have recorded their highest mileage. Extensive analysis with the aid of the MCDM ranking methods demonstrated clearly that cars powered by LPG outperform those powered by ULP. In general, cars tested in June perform better than

Steering levies on the purchase of new cars for the reduction of CO2 emissions

International Nuclear Information System (INIS)

Haan, P. de; Mueller, M.; Peters, A.; Hauser, A.

2007-12-01

This comprehensive final report for the Swiss Federal Office of Energy (SFOE) takes a look at the background, mechanisms and prognoses for the reduction of CO 2 emissions of new cars. This report focuses on policy measures - specifically the collection of budget-neutral so-called 'feebates' - that aim to influence the behaviour of buyers of new cars as a means of enhancing energy efficiency and reducing CO 2 emissions. Both the European Union and Switzerland are pursuing a three-pillar strategy in which agreements with manufacturers and importers (pillar 1) are supplemented by the provision of more detailed information for customers in the form of energy labels for new vehicles as well as catalogues listing levels of fuel consumption (pillar 2). Pillar 3 concerns measures aimed at influencing car buying behaviour, generally based on the use of the energy label for new vehicles in order to realise the existing potentials for reducing CO 2 emissions. The report takes a look at Switzerland's car market, buying behaviour, information on efficient vehicles, acceptance factors and incentive schemes. The findings of the study are presented and commented on.

Real-world European driving cycles, for measuring pollutant emissions from high- and low-powered cars

OpenAIRE

ANDRE, Michel; JOUMARD, Robert; VIDON, Robert; TASSEL, Patrick; PERRET, Pascal

2006-01-01

Pollutant emissions from cars are usually measured on a test bench using driving cycles. However, the use of one unique set of driving cycles to test all cars can be seen as a weak point of emission estimation, as vehicles could conceivably be tested differently depending on their performance levels and usage characteristics. A specific study was then conducted to characterize driving conditions and vehicle usage as a function of vehicle categories, as well as to derive driving cycles special...

Gasoline cars produce more carbonaceous particulate matter than modern filter-equipped diesel cars.

Science.gov (United States)

Platt, S M; El Haddad, I; Pieber, S M; Zardini, A A; Suarez-Bertoa, R; Clairotte, M; Daellenbach, K R; Huang, R-J; Slowik, J G; Hellebust, S; Temime-Roussel, B; Marchand, N; de Gouw, J; Jimenez, J L; Hayes, P L; Robinson, A L; Baltensperger, U; Astorga, C; Prévôt, A S H

2017-07-13

Carbonaceous particulate matter (PM), comprising black carbon (BC), primary organic aerosol (POA) and secondary organic aerosol (SOA, from atmospheric aging of precursors), is a highly toxic vehicle exhaust component. Therefore, understanding vehicle pollution requires knowledge of both primary emissions, and how these emissions age in the atmosphere. We provide a systematic examination of carbonaceous PM emissions and parameterisation of SOA formation from modern diesel and gasoline cars at different temperatures (22, -7 °C) during controlled laboratory experiments. Carbonaceous PM emission and SOA formation is markedly higher from gasoline than diesel particle filter (DPF) and catalyst-equipped diesel cars, more so at -7 °C, contrasting with nitrogen oxides (NO X ). Higher SOA formation from gasoline cars and primary emission reductions for diesels implies gasoline cars will increasingly dominate vehicular total carbonaceous PM, though older non-DPF-equipped diesels will continue to dominate the primary fraction for some time. Supported by state-of-the-art source apportionment of ambient fossil fuel derived PM, our results show that whether gasoline or diesel cars are more polluting depends on the pollutant in question, i.e. that diesel cars are not necessarily worse polluters than gasoline cars.

Experimental Assessment of NOx Emissions from 73 Euro 6 Diesel Passenger Cars.

Science.gov (United States)

Yang, Liuhanzi; Franco, Vicente; Mock, Peter; Kolke, Reinhard; Zhang, Shaojun; Wu, Ye; German, John

2015-12-15

Controlling nitrogen oxides (NOx) emissions from diesel passenger cars during real-world driving is one of the major technical challenges facing diesel auto manufacturers. Three main technologies are available for this purpose: exhaust gas recirculation (EGR), lean-burn NOx traps (LNT), and selective catalytic reduction (SCR). Seventy-three Euro 6 diesel passenger cars (8 EGR only, 40 LNT, and 25 SCR) were tested on a chassis dynamometer over both the European type-approval cycle (NEDC, cold engine start) and the more realistic Worldwide harmonized light-duty test cycle (WLTC version 2.0, hot start) between 2012 and 2015. Most vehicles met the legislative limit of 0.08 g/km of NOx over NEDC (average emission factors by technology: EGR-only 0.07 g/km, LNT 0.04 g/km, and SCR 0.05 g/km), but the average emission factors rose dramatically over WLTC (EGR-only 0.17 g/km, LNT 0.21 g/km, and SCR 0.13 g/km). Five LNT-equipped vehicles exhibited very poor performance over the WLTC, emitting 7-15 times the regulated limit. These results illustrate how diesel NOx emissions are not properly controlled under the current, NEDC-based homologation framework. The upcoming real-driving emissions (RDE) regulation, which mandates an additional on-road emissions test for EU type approvals, could be a step in the right direction to address this problem.

GHG-emissions for cars with different power trains over the whole life cycle

Energy Technology Data Exchange (ETDEWEB)

Roeder, A [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1999-08-01

The method of life-cycle assessment (LCA) has been applied to cars with different power trains. As an example, the results for greenhouse gas (GHG) emissions are presented. They show possibilities and limits for the reduction of these emissions in the transportation sector by means of advanced technology. (author) 2 figs., 4 refs.

Car firms and low-emission vehicles: The evolution of incumbents’ strategies in relation to policy developments

NARCIS (Netherlands)

Bohnsack, R.

2013-01-01

This dissertation explores the developments in the international car industry from 1997 to 2010 in relation to low-emission vehicles, with specific attention to electric vehicles. More specifically, the study seeks to better understand strategies of car manufacturers and the interplay of

Driving cycles for measuring passenger car emissions on roads with traffic calming measures

International Nuclear Information System (INIS)

Boulter, P.G.; Latham, S.; Ainge, M.

1999-01-01

Although local authorities in the UK need to be aware of any air quality impacts resulting from their traffic calming operations, there is little information relating to the effects of different traffic calming measures. The effects on air quality on this scale are complex, and so TRL is providing guidance by developing performance indices for different measures based on their effects on vehicle emissions. The emissions indices for passenger cars are based on tests conducted on a chassis dynamometer, and this paper describes the development of the methodology for constructing the driving cycles to be used. The technique involves the measurement of the speed profiles of a large number of vehicles using a roadside LIDAR system, and the determination of typical gear selections using three-instrumented cars

Impact of passenger car NOX emissions on urban NO2 pollution - Scenario analysis for 8 European cities

Science.gov (United States)

Degraeuwe, Bart; Thunis, Philippe; Clappier, Alain; Weiss, Martin; Lefebvre, Wouter; Janssen, Stijn; Vranckx, Stijn

2017-12-01

Residents of large European cities are exposed to NO2 concentrations that often exceed the established air quality standards. Diesel cars have been identified as a major contributor to this situation; yet, it remains unclear to which levels the NOX emissions of diesel cars have to decrease to effectively mitigate urban NO2 pollution across Europe. Here, we take a continental perspective and model urban NO2 pollution in a generic street canyon of 8 major European cities for various NOX emission scenarios. We find that a reduction in the on-road NOX emissions of diesel cars to the Euro 6 level can in general decrease the regional and urban NO2 concentrations and thereby the frequency of exceedances of the NO2 air quality standard. High NO2 fractions in the NOX emissions of diesel cars tend to increase the urban NO2 concentrations only in proximity of intense road traffic typically found on artery roads in large cities like Paris and London. In cities with a low share of diesel cars in the vehicle fleet such as Athens or a high contribution from the NO2 background to the urban NO2 pollution such as Krakow, measures addressing heavy-duty vehicles, and the manufacturing, energy, and mining industry are necessary to decrease urban air pollution. We regard our model results as robust albeit subject to uncertainty resulting from the application of a generic street layout. With small modifications in the input parameters, our model could be used to assess the impact of NOX emissions from road transport on NO2 air pollution in any European city.

Emission characteristics when using bioethanol as a fuel for passenger cars

International Nuclear Information System (INIS)

Egebaeck, K.E.; Laurikko, J.; Ryden, C.

1998-11-01

In 1991 the Swedish Transport and Communication Research Board (KFB), was asked by the Swedish Government to carry out investigations and field tests in order to demonstrate the possibility of using bioethanol and biogas as automotive fuels. A five-year programme was set up for the investigations and demonstrations and the programme was later extended to a seven-year programme. Despite the fact that most of the work has been directed towards heavy-duty vehicles and especially buses in city traffic some important investigations have been carried out in order to demonstrate the use of bioethanol and biogas in passenger cars. The programme for passenger cars has consisted of running and testing 53 Flexible Fuel Vehicles (FFV), fuelled with bioethanol (E85), a project run by the Swedish Ethanol Development Foundation, and 20 other cars fuelled with biogas, a project carried out by the City of Stockholm's Material Supply Organisation, and sponsored by KFB. For both fleets of vehicles the exhaust emissions have been extensively characterised at a laboratory in Finland owned by the Technical Research Centre of Finland. The aim of this paper is to present some interesting results from the demonstrations of the use of E85 in FFV's and thereby especially focus on the results of the characterisation of both regulated and non-regulated emissions 23 refs, 16 figs, 9 tabs

Emission characteristics when using bioethanol as a fuel for passenger cars

Energy Technology Data Exchange (ETDEWEB)

Egebaeck, K.E. [Luleaa Univ. of Technology, (Sweden); Laurikko, J. [Technical Research Centre of Finland, Helsinki (Finland); Ryden, C. [Tima, (Sweden)

1998-11-01

In 1991 the Swedish Transport and Communication Research Board (KFB), was asked by the Swedish Government to carry out investigations and field tests in order to demonstrate the possibility of using bioethanol and biogas as automotive fuels. A five-year programme was set up for the investigations and demonstrations and the programme was later extended to a seven-year programme. Despite the fact that most of the work has been directed towards heavy-duty vehicles and especially buses in city traffic some important investigations have been carried out in order to demonstrate the use of bioethanol and biogas in passenger cars. The programme for passenger cars has consisted of running and testing 53 Flexible Fuel Vehicles (FFV), fuelled with bioethanol (E85), a project run by the Swedish Ethanol Development Foundation, and 20 other cars fuelled with biogas, a project carried out by the City of Stockholm`s Material Supply Organisation, and sponsored by KFB. For both fleets of vehicles the exhaust emissions have been extensively characterised at a laboratory in Finland owned by the Technical Research Centre of Finland. The aim of this paper is to present some interesting results from the demonstrations of the use of E85 in FFV`s and thereby especially focus on the results of the characterisation of both regulated and non-regulated emissions 23 refs, 16 figs, 9 tabs

The influence of using LPG device on the CO2 emissions from personal passenger cars

Directory of Open Access Journals (Sweden)

Viliam Carach

2007-12-01

Full Text Available Traffic, mostly the air and car traffic is the biggest producer of CO2 (51% at present. CO2 is one of the most important greenhouse gases with more than 50 % of emissions contributing to this major global ecological problem. A rising concetration of CO2 in the atmosphere leads to higher global temperatures. The main problem is the rise of CO2 emissions in most developed countries despite international undertakings accepted in 80´s. This is the main reason for finding solutions to reduce the amount of CO2 emissions in the traffic. One of many solutions is the use of LPG fuel. The purpose of this article is to quantify the efficiency of using LPG in personal passenger cars.

Decomposition analysis of CO2 emissions from passenger cars: The cases of Greece and Denmark

International Nuclear Information System (INIS)

Papagiannaki, Katerina; Diakoulaki, Danae

2009-01-01

The paper presents a decomposition analysis of the changes in carbon dioxide (CO 2 ) emissions from passenger cars in Denmark and Greece, for the period 1990-2005. A time series analysis has been applied based on the logarithmic mean Divisia index I (LMDI I) methodology, which belongs to the wider family of index decomposition approaches. The particularity in road transport that justifies a profound analysis is its remarkably rapid growth during the last decades, followed by a respective increase in emissions. Denmark and Greece have been selected based on the challenging differences of specific socio-economic characteristics of these two small EU countries, as well as on the availability of detailed data used in the frame of the analysis. In both countries, passenger cars are responsible for half of the emissions from road transport as well as for their upward trend, which provokes the implementation of a decomposition analysis focusing exactly on this segment of road transport. The factors examined in the present decomposition analysis are related to vehicles ownership, fuel mix, annual mileage, engine capacity and technology of cars. The comparison of the results discloses the differences in the transportation profiles of the two countries and reveals how they affect the trend of CO 2 emissions.

The impact of fiscal and other measures on new passenger car sales and CO2 emissions intensity. Evidence from Europe

International Nuclear Information System (INIS)

Ryan, Lisa; Convery, Frank; Ferreira, Susana

2009-01-01

This paper examines the impact of national fiscal measures in the EU (EU15) on passenger car sales and the CO 2 emissions intensity of the new car fleet over the period 1995-2004. CO 2 emissions and energy consumption from road transport have been increasing in the EU and as a result since 1999 the EU has attempted to implement a high profile policy strategy to address this problem at European level. Less prominent is the fact that Member States apply vehicle and fuel taxes, which may also be having an impact on the quantity of passenger cars sold and their CO 2 emissions intensity. Diesel vehicle sales have increased appreciably in many countries over the same period and this study makes a first attempt to examine whether Member State fiscal measures have influenced this phenomenon. This work uses a panel dataset to investigate the relationship between national vehicle and fuel taxes on new passenger car sales and the fleet CO 2 emissions intensity in EU15 over a 10-year period. Our results show that national vehicle and fuel taxes have had an impact on passenger car sales and fleet CO 2 emissions intensity and that different taxes have disparate effects. (author)

Developing Singapore Driving Cycle for passenger cars to estimate fuel consumption and vehicular emissions

Science.gov (United States)

Ho, Sze-Hwee; Wong, Yiik-Diew; Chang, Victor Wei-Chung

2014-11-01

Singapore has pledged to attain 7-11% Business-As-Usual carbon emissions reduction by 2020. Road transport sector is a significant source of carbon emissions, estimated to be the third largest sector in Singapore. A current gap in environmental evaluation for road transport activities in Singapore is the lack of a representative driving cycle for passenger cars (64% of the total population of 974,170 vehicles). This Singapore Driving Cycle (SDC) is hence developed for Singapore roads and traffic conditions. A chase-car (instrumented vehicle) was used to collect on-road data along 12 designed routes, and circulation driving on highly utilized arterial roads (including those in Central Business District (CBD) and both inner and outer ring roads fringing the CBD area). The SDC was thus hence constructed, with consideration of road type proportions, time periods and desired distance, duration and peak-lull proportion. In essence, the SDC is a 2400-s speed-time profile to represent the driving pattern for passenger car in Singapore. Microscopic estimation model (CMEM) shows that, as compared to SDC, the New European Driving Cycle (NEDC) underestimates most of the vehicular emissions (fuel, CO2, HC and NOx by 5%, 5%, 22% and 47%, respectively) and overestimates CO by 8%. The SDC is thus more suitable than the NEDC that is currently in use in Singapore; the SDC can be used to generate more accurate fuel consumption and emissions ratings for various uses (for example, inventory of vehicular emissions and fuel economy labelling).

Danish emission inventories for road transport and other mobile sources. Inventories until year 2006

Energy Technology Data Exchange (ETDEWEB)

Winther, M.

2008-09-15

This report explains the parts of the Danish inventories related to road transport and other mobile sources. Emission results are shown for CO{sub 2}, CH{sub 4}, N{sub 2}O, SO{sub 2}, NO{sub X}, NMVOC, CO, particulate matter (PM), heavy metals, dioxins and PAH. From 1990-2006 the fuel use and CO{sub 2} emissions for road transport have increased by 36 %, and CH{sub 4} emissions have decreased by 51 %. A N{sub 2}O emission increase of 29 % is related to the relatively high emissions from older gasoline catalyst cars. The 1985-2006 emission decreases for PM (exhaust only), CO, NO{sub X} and NMVOC are 30, 69, 28 and 71 % respectively, due to the introduction of vehicles complying with gradually stricter emission standards. For SO{sub 2} the emission drop is 99% (due to reduced sulphur content in the diesel fuel), whereas the NH{sub 3} emissions increase by 3065% (due to the introduction of catalyst cars). For other mobile sources the calculated emission changes for CO{sub 2} (and fuel use), CH{sub 4} and N{sub 2}O are -10, 5 and -11%, from 1990 to 2006. The emissions of SO{sub 2}, particulates (all size fractions), NO{sub X}, NMVOC and CO have decreased by 88, 56, 14, 12 and 9% from 1985 to 2006. For NH{sub 3} the emissions have increased by 8% in the same time period. Uncertainties for the emissions and trends have been estimated. (au)

Impact of excess NOx emissions from diesel cars on air quality, public health and eutrophication in Europe

Science.gov (United States)

Jonson, J. E.; Borken-Kleefeld, J.; Simpson, D.; Nyíri, A.; Posch, M.; Heyes, C.

2017-09-01

Diesel cars have been emitting four to seven times more NOx in on-road driving than in type approval tests. These ‘excess emissions’ are a consequence of deliberate design of the vehicle’s after-treatment system, as investigations during the ‘Dieselgate’ scandal have revealed. Here we calculate health and environmental impacts of these excess NOx emissions in all European countries for the year 2013. We use national emissions reported officially under the UNECE Convention for Long-range Transport of Atmospheric Pollutants and employ the EMEP MSC-W Chemistry Transport Model and the GAINS Integrated Assessment Model to determine atmospheric concentrations and resulting impacts. We compare with impacts from hypothetical emissions where light duty diesel vehicles are assumed to emit only as much as their respective type approval limit value or as little as petrol cars of the same age. Excess NO2 concentrations can also have direct health impacts, but these overlap with the impacts from particulate matter (PM) and are not included here. We estimate that almost 10 000 premature deaths from PM2.5 and ozone in the adult population (age >30 years) can be attributed to the NOx emissions from diesel cars and light commercial vehicles in EU28 plus Norway and Switzerland in 2013. About 50% of these could have been avoided if diesel limits had been achieved also in on-road driving; and had diesel cars emitted as little NOx as petrol cars, 80% of these premature deaths could have been avoided. Ecosystem eutrophication impacts (critical load exceedances) from the same diesel vehicles would also have been reduced at similar rates as for the health effects.

Danish emission inventories for road transport and other mobile sources. Inventories until the year 2010

Energy Technology Data Exchange (ETDEWEB)

Winther, M.

2012-08-15

This report explains the parts of the Danish emission inventories related to road transport and other mobile sources. Emission results are shown for CO{sub 2}, CH{sub 4}, N{sub 2}O, SO{sub 2}, NO{sub X}, NMVOC, CO, particulate matter (PM), heavy metals, dioxins and PAH. From 1990-2010 the fuel consumption and CO{sub 2} emissions for road transport increased by 30 %, and CH{sub 4} emissions have decreased by 74 %. A N{sub 2}O emission increase of 29 % is related to the relatively high emissions from older gasoline catalyst cars. The 1985-2010 emission decrease for NO{sub X}, NMVOC, CO and particulates (exhaust only: Size is below PM{sub 2.5}) -52, -84, -81, and -65 %, respectively, due to the introduction of vehicles complying with gradually stricter emission standards. For SO{sub 2} the emission drop 99 % (due to reduced sulphur content in the diesel fuel), whereas the NH{sub 3} emissions increased by 2232 % (due to the introduction of catalyst cars). For other mobile sources the calculated emission changes for CO{sub 2} (and fuel use), CH{sub 4} and N{sub 2}O were -2, 5 and -1 %, from 1990 to 2010. The emissions of SO{sub 2}, particulates (all size fractions), NO{sub X}, NMVOC and CO decreased by 88, 65, 17, 28 and 2 % from 1985 to 2010. For NH{sub 3} the emissions increased by 17 % in the same time period. Uncertainties for the emissions and trends were estimated. (Author)

Environmental Analysis of Petrol, Diesel and Electric Passenger Cars in a Belgian Urban Setting

Directory of Open Access Journals (Sweden)

Nils Hooftman

2016-01-01

Full Text Available The combustion of fossil fuels in the transport sector leads to an aggravation of the air quality along city roads and highways. Urban air quality is a serious problem nowadays as the number of vehicles increases on a yearly basis. With stricter Euro emission regulations, vehicle manufacturers are not meeting the imposed limits and are also disregarding the non-exhaust emissions. This paper highlights the relevance of non-exhaust emissions of passenger vehicles, both conventional (diesel and petrol or electric vehicles (EV, on air quality levels in an urban environment in Belgium. An environmental life cycle assessment was carried out based on a real-world emission model for passenger cars and fuel refinery data. A cut-off was applied to the models to highlight what emissions, both from the refinery to the exhaust and electricity production for EV, do actually occur within Belgium’s borders. Results show that not much progress has been made from Euro 4 to 6 for conventional vehicles. Electric vehicles pose the best alternative solution as a more environmentally friendly means of transportation. The analysis results target policy makers with the intention that regulations and policies would be developed in the future and target the characterization of non-exhaust emissions from vehicles. These results indicate that EVs offer a valid solution for addressing the urban air quality issue and that non-exhaust emissions should be addressed in future regulatory steps as they dominate the impact spectrum.

The emission of BTEX compounds during movement of passenger car in accordance with the NEDC.

Science.gov (United States)

Adamović, Dragan; Dorić, Jovan; Vojinović Miloradov, Mirjana; Adamović, Savka; Pap, Sabolč; Radonić, Jelena; Turk Sekulić, Maja

2018-05-20

The results of the research in the field of benzene, toluene, ethylbenzene and xylene isomers (BTEX) concentrations in exhaust gases of spark ignition engines under different operating conditions are presented in this paper. The aim of this paper is to gain a clearer insight into the impact of different engine working parameters on the concentrations of BTEX. The experimental investigation has been performed on the SCHENCK 230 W test stand with the controlled IC engine. The engine operating points have been chosen based on the results of a simulation and they are considered as the typical driving conditions according to the New European Driving Cycle. Concentration levels of BTEX compounds in exhaust gas mixtures have been determined by gas chromatography technique by using the combination of Supelcowax 10-Polyethylene glycol column and the PID detector. Based on the experimental research results, the emission model of BTEX compounds has been defined by the simulation of movement of a Fiat Punto Classic passenger car in accordance with the NEDC cycle. Using the results obtained within the simulation, the official statistics on the number of gasoline-powered cars on the territory of the Republic of Serbia and the European Commission data on the annual distance traveled by car, the amounts of BTEX compounds emitted annually per car have been estimated, as well as the emissions of the entire Serbian car fleet. Copyright © 2018 Elsevier B.V. All rights reserved.

Danish emission inventories for road transport and other mobile sources. Inventories until year 2004

International Nuclear Information System (INIS)

Winther, M.

2007-01-01

This report explains the parts of the Danish inventories related to road transport and other mobile sources. Emission results for CO 2 , CH 4 , N 2 O, SO 2 , NO X , NMVOC, CO, particulate matter (PM), heavy metals, dioxins and PAH are shown from 1985 to 2004. In this period the fuel use and CO 2 emissions for road transport have increased by 48%. The emission decreases for PM (exhaust only), CO, NO X and NMVOC are 35, 58, 34 and 66% respectively, due to the introduction of vehicles complying with gradually stricter emission standards. A N 2 O emission increase of 301% is related to the high emissions from gasoline catalyst cars. For other mobile sources the fuel use and CO 2 emissions have decreased by 15% from 1985 to 2004. The PM, NO x and NMVOC emission declines are 46, 14 and 10%, respectively. For SO 2 the emission drop is 74% from 1985 to 2004, due to gradually lower fuel sulphur contents. For CO the 1985 and 2004 emissions are the same. Uncertainties for the emissions and trends have been estimated. (au)

Danish emission inventories for road transport and other mobile sources. Inventories until year 2004

Energy Technology Data Exchange (ETDEWEB)

Winther, M. [DMU, Dept. of Policy Analysis (Denmark)

2007-01-15

This report explains the parts of the Danish inventories related to road transport and other mobile sources. Emission results for CO{sub 2}, CH{sub 4}, N{sub 2}O, SO{sub 2}, NO{sub X}, NMVOC, CO, particulate matter (PM), heavy metals, dioxins and PAH are shown from 1985 to 2004. In this period the fuel use and CO{sub 2} emissions for road transport have increased by 48%. The emission decreases for PM (exhaust only), CO, NO{sub X} and NMVOC are 35, 58, 34 and 66% respectively, due to the introduction of vehicles complying with gradually stricter emission standards. A N{sub 2}O emission increase of 301% is related to the high emissions from gasoline catalyst cars. For other mobile sources the fuel use and CO{sub 2} emissions have decreased by 15% from 1985 to 2004. The PM, NO{sub x} and NMVOC emission declines are 46, 14 and 10%, respectively. For SO{sub 2} the emission drop is 74% from 1985 to 2004, due to gradually lower fuel sulphur contents. For CO the 1985 and 2004 emissions are the same. Uncertainties for the emissions and trends have been estimated. (au)

Alternative short tests for inspection and maintenance of in-use cars with respect to their emissions performance

NARCIS (Netherlands)

Samaras, Z.; Zachariadis, T.; Joumard, R.; Vernet, I.; Hassel, D.; Weber, F.-J.; Rijkeboer, R.C.

1998-01-01

This paper presents the first results of a project aimed at evaluation of a number of short tests that can be alternatively used for Inspection and Maintenance of in-use cars emissions performance. For this purpose, a large number of in-use cars from four European countries was tested according to a

Localized innovation, localized diffusion and the environment : an analysis of reductions of CO(2) emissions by passenger cars

NARCIS (Netherlands)

Los, B.; Verspagen, B.

We investigate technological change with regard to CO(2) emissions by passenger cars, using a Free Disposal Hull methodology to estimate technological frontiers. We have a sample of cars available in the UK market in the period 2000-2007. Our results show that the rates of technological change

Localized Innovation, Localized Diffusion and the Environment: An Analysis of CO2 Emission Reductions by Passenger Cars, 2000-2007

OpenAIRE

Los, Bart; Verspagen, Bart

2008-01-01

We investigate technological change with regard to CO2 emissions by passenger cars, using a Free Disposal Hull methodology to estimate technological frontiers. We have a sample of cars available in the UK market in the period 2000 – 2007. Our results show that the rates of technological change (frontier movement) and diffusion (distance to frontier at the car brand level) differ substantial between segments of the car market. We conclude that successful policies should be aimed at diffusion o...

Real world CO2 and NOx emissions from 149 Euro 5 and 6 diesel, gasoline and hybrid passenger cars.

Science.gov (United States)

O'Driscoll, Rosalind; Stettler, Marc E J; Molden, Nick; Oxley, Tim; ApSimon, Helen M

2018-04-15

In this study CO 2 and NO x emissions from 149 Euro 5 and 6 diesel, gasoline and hybrid passenger cars were compared using a Portable Emissions Measurement System (PEMS). The models sampled accounted for 56% of all passenger cars sold in Europe in 2016. We found gasoline vehicles had CO 2 emissions 13-66% higher than diesel. During urban driving, the average CO 2 emission factor was 210.5 (sd. 47) gkm -1 for gasoline and 170.2 (sd. 34) gkm -1 for diesel. Half the gasoline vehicles tested were Gasoline Direct Injection (GDI). Euro 6 GDI engines cars. The average urban NO x emission from Euro 6 diesel vehicles 0.44 (sd. 0.44) gkm -1 was 11 times higher than for gasoline 0.04 (sd. 0.04) gkm -1 . We also analysed two gasoline-electric hybrids which out-performed both gasoline and diesel for NO x and CO 2 . We conclude action is required to mitigate the public health risk created by excessive NO x emissions from modern diesel vehicles. Replacing diesel with gasoline would incur a substantial CO 2 penalty, however greater uptake of hybrid vehicles would likely reduce both CO 2 and NO x emissions. Discrimination of vehicles on the basis of Euro standard is arbitrary and incentives should promote vehicles with the lowest real-world emissions of both NO x and CO 2 . Copyright © 2017 Elsevier B.V. All rights reserved.

Can cars and trucks coexist peacefully on highways? Analyzing the effectiveness of road safety policies in Europe.

Science.gov (United States)

Castillo-Manzano, José I; Castro-Nuño, Mercedes; Fageda, Xavier

2015-04-01

We examine the impact on the traffic accident rate of the interaction between trucks and cars on Europe's roads using a panel data set that covers the period 1999-2010. We find that rising motorization rates for trucks lead to higher traffic fatalities, while rising motorization rates for cars do not. Empirically, the model we build predicts the positive impact of stricter speed limit legislation for trucks in the reduction of road fatalities. These findings lend support to European strategies and aimed at promoting alternative modes of freight transport, including rail and maritime transport. Copyright © 2015 Elsevier Ltd. All rights reserved.

Structure and impacts of fuel economy standards for passenger cars in China

International Nuclear Information System (INIS)

Wagner, David Vance; An Feng; Wang Cheng

2009-01-01

By the end of 2006, there were about 24 million total passenger cars on the roads in China, nearly three times as many as in 2001. To slow the increase in energy consumption by these cars, China began implementing passenger car fuel economy standards in two phases beginning in 2005. Phase 1 fuel consumption limits resulted in a sales-weighted new passenger car average fuel consumption decrease of about 11%, from just over 9 l/100 km to approximately 8 l/100 km, from 2002 to 2006. However, we project that upon completion of Phase 2 limits in 2009, the average fuel consumption of new passenger cars in China may drop only by an additional 1%, to approximately 7.9 l/100 km. This is due to the fact that a majority of cars sold in 2006 already meets the stricter second phase fuel consumption limits. Simultaneously, other trends in the Chinese vehicle market, including increases in average curb weight and increases in standards-exempt imported vehicles, threaten to offset the efficiency gains achieved from 2002 to 2006. It is clear that additional efforts and policies beyond Phase 2 fuel consumption limits are required to slow and, ultimately, reverse the trend of rapidly rising energy consumption and greenhouse gases from China's transportation sector.

The study of envorinmental state on road intersections based on emissions of car engines in Zhytomyr

Directory of Open Access Journals (Sweden)

Titarenko V.

2016-08-01

Full Text Available This paper presents results of the studies of environmental conditions on road intersections based on car engine emissions in Zhitomir. Statistical methods were used to determine the intensity of traffic flows based on transport emissions according to video monitoring records. Intersections with the highest intensity of traffic flows, where there is a high risk of car emissions accumulation above the applicable standard, were chosen for the assessment of ecological sustainability. Calculation of pollution was done for the intersection of Nebesnoi Sotni street and M. Grushevskogo street. The results of calculation were compared with the limit of affordable concentration and conclusions that emphasize difficulty of the problem and the emergence of its solving. The system of ecological safety in Zhitomir requires significant improvements taking into account the exceeding of factual values of pollution over normative values. Recommendations concerning of ecological sustainability of intersections can be developed through the optimization of traffic flows with the use of intellectual traffic systems.

Vehicle emissions and consumer information in car advertisements

Directory of Open Access Journals (Sweden)

Thomson George

2008-04-01

Full Text Available Abstract Background The advertising of vehicles has been studied from a safety perspective but not in terms of vehicle air pollutants. We aimed to examine the content and trends of greenhouse gas emissions and air pollution-related information, in light passenger vehicle advertisements. Methods Content analysis of the two most popular current affairs magazines in New Zealand for the five year period 2001–2005 was undertaken (n = 514 advertisements. This was supplemented with vehicle data from official websites. Results The advertisements studied provided some information on fuel type (52%, and engine size (39%; but hardly any provided information on fuel efficiency (3%, or emissions (4%. Over the five-year period the reported engine size increased significantly, while fuel efficiency did not improve. For the vehicles advertised, for which relevant official website data could be obtained, the average "greenhouse rating" for carbon dioxide (CO2 emissions was 5.1, with a range from 0.5 to 8.5 (on a scale with 10 being the best and 0.5 being the most polluting. The average CO2 emissions were 50% higher than the average for cars made by European manufacturers. The average "air pollution" rating for the advertised vehicles was 5.4 (on the same 1–10 scale. The yearly averages for the "greenhouse" or "air pollution" ratings did not change significantly over the five-year period. One advertised hybrid vehicle had a fuel consumption that was under half the average (4.4 versus 9.9 L/100 km, as well as the best "greenhouse" and "air pollution" ratings. Conclusion To enhance informed consumer choice and to control greenhouse gas and air pollution emissions, governments should introduce regulations on the content of vehicle advertisements and marketing (as started by the European Union. Similar regulations are already in place for the marketing of many other consumer products.

Vehicle emissions and consumer information in car advertisements

Science.gov (United States)

Wilson, Nick; Maher, Anthony; Thomson, George; Keall, Michael

2008-01-01

Background The advertising of vehicles has been studied from a safety perspective but not in terms of vehicle air pollutants. We aimed to examine the content and trends of greenhouse gas emissions and air pollution-related information, in light passenger vehicle advertisements. Methods Content analysis of the two most popular current affairs magazines in New Zealand for the five year period 2001–2005 was undertaken (n = 514 advertisements). This was supplemented with vehicle data from official websites. Results The advertisements studied provided some information on fuel type (52%), and engine size (39%); but hardly any provided information on fuel efficiency (3%), or emissions (4%). Over the five-year period the reported engine size increased significantly, while fuel efficiency did not improve. For the vehicles advertised, for which relevant official website data could be obtained, the average "greenhouse rating" for carbon dioxide (CO2) emissions was 5.1, with a range from 0.5 to 8.5 (on a scale with 10 being the best and 0.5 being the most polluting). The average CO2 emissions were 50% higher than the average for cars made by European manufacturers. The average "air pollution" rating for the advertised vehicles was 5.4 (on the same 1–10 scale). The yearly averages for the "greenhouse" or "air pollution" ratings did not change significantly over the five-year period. One advertised hybrid vehicle had a fuel consumption that was under half the average (4.4 versus 9.9 L/100 km), as well as the best "greenhouse" and "air pollution" ratings. Conclusion To enhance informed consumer choice and to control greenhouse gas and air pollution emissions, governments should introduce regulations on the content of vehicle advertisements and marketing (as started by the European Union). Similar regulations are already in place for the marketing of many other consumer products. PMID:18445291

Vehicle emissions and consumer information in car advertisements.

Science.gov (United States)

Wilson, Nick; Maher, Anthony; Thomson, George; Keall, Michael

2008-04-29

The advertising of vehicles has been studied from a safety perspective but not in terms of vehicle air pollutants. We aimed to examine the content and trends of greenhouse gas emissions and air pollution-related information, in light passenger vehicle advertisements. Content analysis of the two most popular current affairs magazines in New Zealand for the five year period 2001-2005 was undertaken (n = 514 advertisements). This was supplemented with vehicle data from official websites. The advertisements studied provided some information on fuel type (52%), and engine size (39%); but hardly any provided information on fuel efficiency (3%), or emissions (4%). Over the five-year period the reported engine size increased significantly, while fuel efficiency did not improve. For the vehicles advertised, for which relevant official website data could be obtained, the average "greenhouse rating" for carbon dioxide (CO2) emissions was 5.1, with a range from 0.5 to 8.5 (on a scale with 10 being the best and 0.5 being the most polluting). The average CO2 emissions were 50% higher than the average for cars made by European manufacturers. The average "air pollution" rating for the advertised vehicles was 5.4 (on the same 1-10 scale). The yearly averages for the "greenhouse" or "air pollution" ratings did not change significantly over the five-year period. One advertised hybrid vehicle had a fuel consumption that was under half the average (4.4 versus 9.9 L/100 km), as well as the best "greenhouse" and "air pollution" ratings. To enhance informed consumer choice and to control greenhouse gas and air pollution emissions, governments should introduce regulations on the content of vehicle advertisements and marketing (as started by the European Union). Similar regulations are already in place for the marketing of many other consumer products.

An investigation of engine performance parameters and artificial intelligent emission prediction of hydrogen powered car

International Nuclear Information System (INIS)

Ho, Tien; Karri, Vishy; Lim, Daniel; Barret, Danny

2008-01-01

With the depletion of fossil fuel resources and the potential consequences of climate change due to fossil fuel use, much effort has been put into the search for alternative fuels for transportation. Although there are several potential alternative fuels, which have low impact on the environment, none of these fuels have the ability to be used as the sole 'fuel of the future'. One fuel which is likely to become a part of the over all solution to the transportation fuel dilemma is hydrogen. In this paper, The Toyota Corolla four cylinder, 1.8 l engine running on petrol is systematically converted to run on hydrogen. Several ancillary instruments for measuring various engine operating parameters and emissions are fitted to appraise the performance of the hydrogen car. The effect of hydrogen as a fuel compares with gasoline on engine operating parameters and effect of engine operating parameters on emission characteristics is discussed. Based on the experimental setup, a suite of neural network models were tested to accurately predict the effect of major engine operating conditions on the hydrogen car emissions. Predictions were found to be ±4% to the experimental values. This work provided better understanding of the effect of engine process parameters on emissions. (author)

California Dreaming - Sustaining American Lifestyle and the Car

DEFF Research Database (Denmark)

Jørgensen, Ulrik

2001-01-01

California has for several years supported new innovation in zero-emission and low emission cars and set measures for the reduction of emissions in the state for the coming years.......California has for several years supported new innovation in zero-emission and low emission cars and set measures for the reduction of emissions in the state for the coming years....

On-board measurement of emissions from liquefied petroleum gas, gasoline and diesel powered passenger cars in Algeria

OpenAIRE

Chikhi , Saâdane; Boughedaoui , Ménouèr; Kerbachi , Rabah; Joumard , Robert

2014-01-01

International audience; On-board measurements of unit emissions of CO, HC, NOx and CO 2 were conducted on 17 private cars powered by different types of fuels including gasoline, dual gasoline-LPG, gasoline, and diesel. The tests performed revealed the effect of LPG injection technology on unit emissions and made it possible to compare the measured emissions to the European Artemis emission model. A sequential multipoint injection LPG kit with no catalyst installed was found to be the most eff...

Company car study 2011. Reduction of environmental impacts by influencing the selection process of company cars; Tyoesuhdeautotutkimus 2011. Ympaeristoehaittojen vaehentaeminen autonvalinnan ohjauksella

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

The purpose of the study is to identify: What kinds of operational models directing towards eco-friendlier company car use there are and which are in use. What kinds of practical impacts these operational models have had. What is the demand for company car use and what changes have taken place from the viewpoint of companies and beneficiaries. What factors should the best company car taxation include in terms of directiveness (from the environmental point of view). The main objective is to find directive factors in company car use which would result in smaller environmental impacts and which company car users could commit themselves to. The main target groups of the study were the recipients of company car benefits, and enterprises using company cars. Company cars are mainly used for two reasons: in many organisations, work is carried out where the customer is, in which case company cars are used for reducing travel costs. On the other hand, a company car is a significant means for attracting and motivating employees, especially skilled experts and management staff. Company cars also play a significant role in the replacement rate of Finnish motor vehicles. The car selection rules of organisations determine the roles that entitle an employee to have a company car and how they can choose their car. Factors restricting the choice are usually CO{sub 2} and the price and make of the car. The CO{sub 2} limit is used by about 70% of organisations. According to this study, the average emission limit is 168 g/km, depending on the company and the position of the beneficiary. However, the average CO{sub 2} emissions of new company cars are currently about 140 g/km, and therefore the emission limits of organisations have not followed the development of motor technology. In entrepreneurship, environmental issues will be regarded as very important in the future, and there is also a notion for this to be reflected in the guidelines for selecting company cars. Emissions reduction

Actual car fleet emissions estimated from urban air quality measurements and street pollution models

International Nuclear Information System (INIS)

Palmgren, F.; Berkowicz, R.; Hertel, O.; Ziv, A.

1999-01-01

A method to determine emissions from the actual car fleet under realistic driving conditions has been developed. The method is based on air quality measurements, traffic counts and inverse application of street air quality models. Many pollutants are of importance for assessing the adverse impact of the air pollution, e.g. NO 2 , CO, lead, VOCs and particulate matter. Aromatic VOCs are of special great concern due to their adverse health effects. Measurements of benzene, toluene and xylenes were carried out in central Copenhagen since 1994. Significant correlation was observed between VOCs and CO concentrations, indicating that the petrol engine vehicles are the major sources of VOC air pollution in central Copenhagen. Hourly mean concentrations of benzene were observed to reach values of up to 20 ppb, what is critically high according to the WHOs recommendations. Based on inverse model calculation of dispersion of pollutants in street canyons, an average emission factor of benzene for the fleet of petrol fuelled vehicles was estimated to be 0.38 g/km in 1994 and 0.11 in 1997. This decrease was caused by the reduction of benzene content in Danish petrol since summer 1995 and increasing percentage of cars equipped with three-way catalysts. The emission factors for benzene for diesel-fuelled vehicles were low

Development and review of Euro 5 passenger car emission factors based on experimental results over various driving cycles.

Science.gov (United States)

Fontaras, Georgios; Franco, Vicente; Dilara, Panagiota; Martini, Giorgio; Manfredi, Urbano

2014-01-15

The emissions of CO2 and regulated pollutants (NOx, HC, CO, PM) of thirteen Euro 5 compliant passenger cars (seven gasoline, six Diesel) were measured on a chassis dynamometer. The vehicles were driven repeatedly over the European type-approval driving cycle (NEDC) and the more dynamic WMTC and CADC driving cycles. Distance-specific emission factors were derived for each pollutant and sub-cycle, and these were subsequently compared to the corresponding emission factors provided by the reference European models used for vehicle emission inventory compilation (COPERT and HBEFA) and put in context with the applicable European emission limits. The measured emissions stayed below the legal emission limits when the type-approval cycle (NEDC) was used. Over the more dynamic cycles (considered more representative of real-world driving) the emissions were consistently higher but in most cases remained below the type-approval limit. The high NOx emissions of Diesel vehicles under real-world driving conditions remain the main cause for environmental concern regarding the emission profile of Euro 5 passenger cars. Measured emissions of NOx exceeded the type-approval limits (up to 5 times in extreme cases) and presented significantly increased average values (0.35 g/km for urban driving and 0.56 g/km for motorway driving). The comparison with the reference models showed good correlation in all cases, a positive finding considering the importance of these tools in emission monitoring and policy-making processes. © 2013. Published by Elsevier B.V. All rights reserved.

Temporal and spatial variation in recent vehicular emission inventories in China based on dynamic emission factors.

Science.gov (United States)

Cai, Hao; Xie, Shaodong

2013-03-01

The vehicular emission trend in China was tracked for the recent period 2006-2009 based on a database of dynamic emission factors of CO, nonmethane volatile organic compounds (NMVOC), NOx, PM10, CO2, CH4, and N2O for all categories of on-road motor vehicles in China, which was developed at the provincial level using the COPERT 4 model, to account for the effects of rapid advances in engine technologies, implementation of improved emission standards, emission deterioration due to mileage, and fuel quality improvement. Results show that growth rates of CO and NMVOC emissions slowed down, but NOx and PM10 emissions continued rising rapidly for the period 2006-2009. Moreover CO2, CH4, and N2O emissions in 2009 almost doubled compared to those in 2005. Characteristics of recent spatial distribution of emissions and emission contributions by vehicle category revealed that priority of vehicular emission control should be put on the eastern and southeastern coastal provinces and northern regions, and passenger cars and motorcycles require stricter control for the reduction of CO and NMVOC emissions, while effective reduction of NOx and PM10 emissions can be achieved by better control of heavy-duty vehicles, buses and coaches, and passenger cars. Explicit provincial-level Monte Carlo uncertainty analysis, which quantified for the first time the Chinese vehicular emission uncertainties associated with both COPERT-derived and domestically measured emission factors by vehicle technology, showed that CO, NMVOC, and NOx emissions for the period 2006-2009 were calculated with the least uncertainty, followed by PM10 and CO2, despite relatively larger uncertainties in N2O and CH4 emissions. The quantified low uncertainties of emissions revealed a necessity of applying vehicle technology- and vehicle age-specific dynamic emission factors for vehicular emission estimation, and these improved methodologies are applicable for routine update and forecast of China's on-road motor vehicle

Estimates the Emission of Passenger Cars Based on the First Developed Driving Cycle in Nakhon Ratchasima Municipality, Thailand

Directory of Open Access Journals (Sweden)

Muangnak Noppatsorn

2017-01-01

Full Text Available This study aims to estimate emissions of passenger cars traveled on the highways in Nakhon Ratchasima Municipality (NRM based on recently developed driving cycles. A mobile phone application (SafeMate was used to record speed-time of passenger car on the highways both weekday and weekend. The results showed that the driving cycles of the passenger cars on highway 224 and 304 were quite different. More traffic congestion on highway 224 impacted the average speeds, ranging from 10 to 34 km/h with longer idling time. The average speeds on highway 304 ranged from 49 to 69 km/h with more cruise time. The combined driving cycles on both highways showed the average speeds of 20-40 km/h depending upon the time of days. The traffic density on weekday was higher than the weekend. Peak-hour weekday showed lower traffic flow than off-peak hour which was the opposite of the weekend. Based on the derived driving cycles, the passenger car traveled on the highways in NRM emitted CO, NOx and HC approximately 90.7-129.8, 25.5-34.5 and 6.9-11.7 tons/year, respectively. The passenger cars were estimated to emit about 13,927.7-20,419.3 tons/year of carbon dioxide on the highways. The highway 2 accounted more of the emissions due to the traffic volume and coverage distance in NRM.

On-road magnetic emissions prediction of electric cars in terms of driving dynamics using neural networks

NARCIS (Netherlands)

Wefky, Ahmed M.; Espinosa, Felipe; Leferink, Frank Bernardus Johannes; Gardel, Alfredo; Vogt-Ardatjew, R.A.

2013-01-01

This paper presents a novel artificial neural network (ANN) model estimating vehicle-level radiated magnetic emissions of an electric car as a function of the corresponding driving pattern. Real world electromagnetic interference (EMI) experiments have been realized in a semi-anechoic chamber using

Land use changes, greenhouse gas emissions and fossil fuel substitution of biofuels compared to bioelectricity production for electric cars in Austria

International Nuclear Information System (INIS)

Schmidt, Johannes; Gass, Viktoria; Schmid, Erwin

2011-01-01

Bioenergy is one way of achieving the indicative target of 10% renewable energy in the transportation sector outlined in the EU Directive 2009/28/EC. This article assesses the consequences of increasing the use of bioenergy for road transportation on land use, greenhouse gas (GHG) emissions, and fossil fuel substitution. Different technologies, including first and second generation fuels and electric cars fuelled by bioelectricity are assessed in relation to existing bioenergy uses for heat and power production. The article applies a spatially explicit energy system model that is coupled with a land use optimization model to allow assessing impacts of increased biomass utilization for energy production on land use in agriculture and forest wood harvests. Uncertainty is explicitly assessed with Monte-Carlo simulations of model parameters. Results indicate that electric mobility could save GHG emissions without causing a significant increase in domestic land use for energy crop production. Costs of electric cars are still prohibitive. Second generation biofuels are more effective in producing fuels than first generation ethanol. However, competition with power and heat production from ligno-cellulosic feedstock causes an increase in GHG emissions when introducing second generation fuels in comparison to a baseline scenario. -- Highlights: → Assessment of land use and greenhouse gas emissions (GHG) of renewable transportation options. → Optimization model compares 1st and 2nd generation biofuels and bioelectricity for electric cars. → Use of agricultural land for 1st generation ethanol production is highest among options. → 2nd generation fuel production deviates resources from efficient heat and power production. → Electric cars use less land and save more GHG emissions than other options but costs are prohibitive.

Car sick.

Science.gov (United States)

Renner, M G

1988-01-01

The automobile is currently seen as the most desirable mode of transportation. However, this view needs to be changed since the proliferation of the automobile worldwide is leading to the poisoning of the environment and people. In the US the number of passenger cars grew 51% between 1971-86 and in the noncommunist industrialized community that figure is 71%. The gasoline and diesel fuel used to power the overwhelming majority of cars creates a variety of problems. The pollution is estimated to have a hidden cost of US $.80/gallon. Others estimate that the pollution causes 30,000 premature deaths annually just in the US. 75% of the carbon monoxide (CO), 48% of nitrogen oxides (NO2), 13% of particulates (P), and 3% of sulfur (S) emissions come from cars in the countries of the Organization for Economic Cooperation and Development (OECD), which includes the US, Canada, Western Europe, Japan, Australia, and New Zealand. 17% of all worldwide carbon dioxide (CO2) emission comes from the production and use of fossil fuels for cars. The single biggest problem associated with cars is the photochemical smog they create in urban areas. In 1986 75 million Americans lived in areas that failed to meet national air quality standards for CO, P, and ozone (03). The only area of major improvement has been the removal of lead from gasoline. It was known to cause problems from the beginning of its use in the 1920s, but remained for 50 years because of auto and oil company pressure. Ground 03 is estimated by the US government to cost US $4 billion in annual losses, just for corn, wheat, soybeans, and peanuts. Acid rain is the other major problem associated with cars, and its damage is estimated at US $5 billion annually. Both these problems are shortterm, their effects occur immediately; the longterm disadvantage is the build up of CO2 and its contribution to the greenhouse effect. While the US is at the forefront of regulation and many other countries are modeling their emission

Influence of European passenger cars weight to exhaust CO2 emissions

International Nuclear Information System (INIS)

Zervas, Efthimios; Lazarou, Christos

2008-01-01

The increase of atmospheric CO 2 concentration influences climate changes. The road transport sector is one of the main anthropogenic sources of CO 2 emissions in the European Union (EU). One of the main parameters influencing CO 2 emissions from passenger cars (PCs) is their weight, which increases during last years. For the same driving distance, heavier vehicles need more work than lighter ones, because they have to move an extra weight, and thus more fuel is consumed and thus increased CO 2 emissions. The weight control of new PCs could be an efficient way to control their CO 2 emissions. After an analysis of the EU new PCs market, their segment distribution and their weight, some estimations for 2020 are presented. Based on this analysis, 13 base scenarios using several ways for the control of the weight of future European new PCs are used to estimate their CO 2 emissions and the benefit of each scenario. The results show that a significant benefit on CO 2 emissions could be achieved if the weight of each PC does not exceed an upper limit, especially if this limit is quite low. The benefit obtained by limitations of weight is higher than the benefit obtained from the expected decreased future fuel consumption. Similar results are obtained when the weight of new PCs does not exceed an upper limit within each segment, or when the weight of each new PC decreases. (author)

Lifestyle and energy consumption, part 2: Less weighty cars and holiday in your own country; Leefstijl en energiegebruik, deel 2: Lichtere auto`s en vakantie in eigen land

Energy Technology Data Exchange (ETDEWEB)

Schmidt, T.; Postma, A. [Bureau voor Communicatie en Advies over Energie and Milieu CEA, Rotterdam (Netherlands); Raaijen, W. [ed.

1995-06-01

Part two of the series on `lifestyle and energy consumption` focuses on mobility. Over the last few years we have been moving more and more to the detriment of the environment. The car is largely to blame for this development. The Dutch Government has tried to make cars cleaner and more economical by setting stricter environmental requirements, making catalytic converters obligatory and fostering the use of unleaded petrol. At the same time, however, the Dutch are increasingly driving bigger cars, car manufacturers are offering faster, bigger and heavier cars and car drivers soon consider more economical cars a licence to drive more kilometres. Holidays also offer an opportunity to save energy. CEA (Bureau for Communication and Advice on Energy and the Environment) and the journal Gas calculated the environmental impact of three different alternatives: biking across the Netherlands, travelling throughout France by car and flying to Indonesia. 3 tabs., 3 figs.

EU policies on car emissions and fuel quality. Reducing the climate impact from road transport

Energy Technology Data Exchange (ETDEWEB)

Christensen, Anne Raaum; Gulbrandsen, Lars H.

2012-07-01

Transport is the second biggest source of greenhouse gas (GHG) emissions in the EU, and contributes about one-quarter of the EU's total emissions of CO{sub 2}. Significant reductions in GHG emissions from transport are required if the EU is to achieve its long-term climate goals. This report examines the making and implementation of two of the regulations the EU has put in place to lower emissions from the transport sector: the EU's revised Fuel Quality Directive (Directive 2009/30/EC) and the cars/CO{sub 2} regulation (Regulation (EC) 443/2009). It was found that the relevance of various theories of policymaking in the EU varies with different policy phases. A policy-network understanding of EU policymaking is strengthened when assessing the policy-initiation phase. The Commission played a key role in this phase and drafted legislation in close collaboration with the car and oil refining industries. An intergovernmentalist understanding of EU policy-making is strengthened when assessing the decision-making phase. In this phase, member states defending the interests of their domestic industries had strong influence, but the European Parliament played an important role in this phase too, employing its power in the co-decision procedure. Finally, the implementation process is best understood as a multi-level governance process in which several actors and institutions - notably the Commission, member states, industries, and NGOs - influenced the process. (Author)

Estimation of CO{sub 2}-emissions from Fires in Dwellings, Schools and Cars in the Nordic Countries

Energy Technology Data Exchange (ETDEWEB)

Blomqvist, Per; Simonson McNamee, Margaret

2009-07-01

Updated estimates of emissions from fires in dwellings, schools, pre schools and cars are presented for the Nordic countries with the exception of Iceland. The updated emissions are calculated based on fire statistics from 2007 and are compared to results previously presented for 1994 in Sweden. To put the fire emissions data into perspective they are also compared to national estimates of CO{sub 2} emissions as reported by the Swedish EPA to the EU in their National Inventory Report for 2007. The statistical data on fires for Sweden for 2007 is more reliable compared with the data for 1994, which strengthens the updated emission estimate. The major uncertainty in the fire data used for the emission estimate is the interpretation of fire spread which is based on rather crude assumptions. In particular in the case of houses the fire spread area used for the estimate may be an exaggeration thereby giving a possible overestimation of the estimated emissions. Data indicates that the total emission of CO{sub 2} from fires in dwellings (including single family homes, semi-detached houses, summer houses and apartments) in Sweden 2007 is 15,5 kton. Similar values for Denmark (4,1 kton), Finland (6,9 kton) and Norway (6,4 kton). Similar data for school/preschool and car fires indicate that emissions in Sweden are higher than in the other Nordic countries for these categories as well although not by as great an amount. Finally, a comparison between emissions data from other sources of CO{sub 2} and those from fires indicate that emissions of CO{sub 2} from fires are minor compared to most other sources. The previous study based on statistics from 1994 also concluded that fires are a minor source of CO{sub 2} but a relatively significant source of, e.g., particulate matter, VOC, PAH and other large organic species

Development and review of Euro 5 passenger car emission factors based on experimental results over various driving cycles

OpenAIRE

Fontaras, Georgios; Franco, Vicente; Dilara, Panagiota; Martini, Giorgio; Manfredi, Urbano

2014-01-01

The mass emissions of CO2 and regulated pollutants (NOX, HC, CO, PM) of thirteen Euro 5 compliant passenger cars (seven gasoline, six Diesel) were measured on a chassis dynamometer. The vehicles were driven repeatedly over the European type-approval driving cycle (NEDC) and the more dynamic WMTC and CADC driving cycles. Distance-specific emission factors were derived for each pollutant and sub-cycle which were subsequently compared to the corresponding emission factors provided by the referen...

The impact of tax reform on new car purchases in Ireland

International Nuclear Information System (INIS)

Hennessy, Hugh; Tol, Richard S.J.

2011-01-01

We examine the impact of recent tax reforms in Ireland on private car transport and its greenhouse gas emissions. A carbon tax was introduced on fuels, and purchase (vehicle registration) and ownership (motor) taxes were switched from engine size to potential emissions. We use a demographic model of the car stock (by age, size, and fuel) and a car purchase model that reflects the heterogeneous distribution of mileage and usage costs across various engine sizes. The model shows a dramatic shift from petrol to diesel cars, particularly for large engines. The same pattern is observed in the latest data on car sales. This has a substantial impact on tax revenue as car owners shift to the lower tax rates. The tax burden has shifted from car ownership to car use, and that the overall tax burden on private car transport falls. As diesel engines are more fuel efficient than petrol engines, carbon dioxide emissions fall modestly or, if we consider the rebound effect of travel costs on mileage, minimally. From the perspective of the revenue, the costs per tonne of carbon dioxide avoided are (very) high. - Highlights: → Ireland has reform fuel and car taxes to inventivize emission reduction. → These tax reforms are likely to cause a large shift from petrol to diesel cars. → Carbon dioxide emissions will fall as a result. → Tax revenues will fall too. → The exchequer cost per tonne of CO 2 avoided is very high.

The ARTEMIS European driving cycles for measuring car pollutant emissions.

Science.gov (United States)

André, Michel

2004-12-01

In the past 10 years, various work has been undertaken to collect data on the actual driving of European cars and to derive representative real-world driving cycles. A compilation and synthesis of this work is provided in this paper. In the frame of the European research project: ARTEMIS, this work has been considered to derive a set of reference driving cycles. The main objectives were as follows: to derive a common set of reference real-world driving cycles to be used in the frame of the ARTEMIS project but also in the frame of on-going national campaigns of pollutant emission measurements, to ensure the compatibility and integration of all the resulting emission data in the European systems of emission inventory; to ensure and validate the representativity of the database and driving cycles by comparing and taking into account all the available data regarding driving conditions; to include in three real-world driving cycles (urban, rural road and motorway) the diversity of the observed driving conditions, within sub-cycles allowing a disaggregation of the emissions according to more specific driving conditions (congested and free-flow urban). Such driving cycles present a real advantage as they are derived from a large database, using a methodology that was widely discussed and approved. In the main, these ARTEMIS driving cycles were designed using the available data, and the method of analysis was based to some extent on previous work. Specific steps were implemented. The study includes characterisation of driving conditions and vehicle uses. Starting conditions and gearbox use are also taken into account.

Study of a method for reducing fuel consumption and the amount of specific emissions of harmful substances with exhaust gases of passenger cars when using the “climate control” system

Science.gov (United States)

Burakova, L. N.; Anisimov, I. A.; Burakova, A. D.; Burakova, O. D.

2018-05-01

The article deals with the issue of improving the fuel economy and environmental friendliness of motor vehicles which serve the administrative and management personnel of the oil and gas industry. It is established that fuel consumption and the amount of specific emissions of harmful substances with exhaust gases of cars when using the “climate control” system depend on the effective ambient temperature, the color of the opaque car body elements, the power of the car engine and the interior volume. However, the simplest controlled factor is the color of the opaque car body elements, which is characterized by the coefficient of light reflection. In the course of experimental studies, we established the dependences of a change in fuel consumption and a share of reducing emissions of harmful substances with exhaust gases of passenger cars with the “climate control” system on the coefficient of light reflection. A method has been developed to reduce fuel consumption and the amount of specific emissions of harmful substances with the exhaust gases of passenger cars using the “climate control” system, which involves painting the vehicle roof white and allows reducing fuel consumption by 5.5-10.3%, and the amount of specific emissions of harmful substances by 0.8-2.3%.

X-RAY EMISSION FROM THE DOUBLE-BINARY OB-STAR SYSTEM QZ CAR (HD 93206)

International Nuclear Information System (INIS)

Parkin, E. R.; Naze, Y.; Rauw, G.; Broos, P. S.; Townsley, L. K.; Pittard, J. M.; Moffat, A. F. J.; Oskinova, L. M.; Waldron, W. L.

2011-01-01

X-ray observations of the double-binary OB-star system QZ Car (HD 93206) obtained with the Chandra X-ray Observatory over a period of roughly 2 years are presented. The respective orbits of systems A (O9.7 I+b2 v, P A = 21 days) and B (O8 III+o9 v, P B = 6 days) are reasonably well sampled by the observations, allowing the origin of the X-ray emission to be examined in detail. The X-ray spectra can be well fitted by an attenuated three-temperature thermal plasma model, characterized by cool, moderate, and hot plasma components at kT ≅ 0.2, 0.7, and 2 keV, respectively, and a circumstellar absorption of ≅0.2 x 10 22 cm -2 . Although the hot plasma component could be indicating the presence of wind-wind collision shocks in the system, the model fluxes calculated from spectral fits, with an average value of ≅7 x 10 -13 erg s -1 cm -2 , do not show a clear correlation with the orbits of the two constituent binaries. A semi-analytical model of QZ Car reveals that a stable momentum balance may not be established in either system A or B. Yet, despite this, system B is expected to produce an observed X-ray flux well in excess of the observations. If one considers the wind of the O8 III star to be disrupted by mass transfer, the model and observations are in far better agreement, which lends support to the previous suggestion of mass transfer in the O8 III + o9 v binary. We conclude that the X-ray emission from QZ Car can be reasonably well accounted for by a combination of contributions mainly from the single stars and the mutual wind-wind collision between systems A and B.

Analysis of the CO2 emissions and of the other characteristics of the European market of new passenger cars. Part 1. Analysis of general data and analysis per country

International Nuclear Information System (INIS)

Zervas, Efthimios

2010-01-01

Exhaust CO 2 emitted from passenger cars is one of the major greenhouse effect gases. Several parameters influence the exhaust CO 2 emissions of each passenger car: its characteristics (fuel used, vehicle weight,..) and its use (annual mileage, driving conditions,..). CO 2 emissions from passenger cars decrease during last years; however, this decrease seems to reach its limits. Several parameters of the EU15 new PCs market, such as new passenger cars registrations, type of fuel used, engine capacity, max. power, max. specific power, segment distribution, vehicle weight and their CO 2 emissions on the New European Driving Cycle are analyzed here. The target is to find the real market parameters influencing exhaust CO 2 emissions. Because of the many data used and the parameters examined, this first part of the work is focused on the average values of each parameter studied and the values of each country, while the second part is based on the analysis of each PC segment and the third one on the analysis of the major brands presented in the European market. (author)

Climate effects of non-compliant Volkswagen diesel cars

Science.gov (United States)

Tanaka, Katsumasa; Lund, Marianne T.; Aamaas, Borgar; Berntsen, Terje

2018-04-01

On-road operations of Volkswagen light-duty diesel vehicles equipped with defeat devices cause emissions of NOx up to 40 times above emission standards. Higher on-road NOx emissions are a widespread problem not limited to Volkswagen vehicles, but the Volkswagen violations brought this issue under the spotlight. While several studies investigated the health impacts of high NOx emissions, the climatic impacts have not been quantified. Here we show that such diesel cars generate a larger warming on the time scale of several years but a smaller warming on the decadal time scale during actual on-road operations than in vehicle certification tests. The difference in longer-term warming levels, however, depends on underlying driving conditions. Furthermore, in the presence of defeat devices, the climatic advantage of ‘clean diesel’ cars over gasoline cars, in terms of global-mean temperature change, is in our view not necessarily the case.

Polycyclic aromatic hydrocarbons (PAH) and diesel engine emission (elemental carbon) inside a car and a subway train.

Science.gov (United States)

Fromme, H; Oddoy, A; Piloty, M; Krause, M; Lahrz, T

1998-06-30

Significant concentrations of potentially harmful substances can be present in the interior of vehicles. The main sources of PAHs and elemental carbon (EC) inside a car are likely to be combustion emissions, especially from coal and traffic. The same sources can also be important for the interior of a subway train for which there are specific sources in the tunnel system, for example diesel engines. Twice, in summer 1995 and winter 1996 polycyclic aromatic hydrocarbons (PAH) and diesel motor emission (estimated as elemental carbon) were determined in the interior of a car (a 2-year-old VW Golf with a three-way catalytic converter) and in the passenger compartment of a subway train (below ground). On each sampling day (in total 16 daily measurements in the car and 16 in the subway) the substances were determined in the breathing zone of the passengers from 07:00 h to 16:00 h under different meteorologic conditions (winter- and summertime). The car followed the route of the subway from the western Berlin borough of Spandau to the south-eastern borough of Neukölln, and back. The sampling represented a realistic exposure model for driving in a high traffic and polluted urban area. The electric subway train (also 2 years in use) connected the same parts of Berlin (31 km underground). The mean values obtained during the two measurement periods (summer/winter) inside the car were 1.0 and 3.2 ng/m3 for benzo[a]pyrene, 10.2 and 28.7 ng/m3 for total-measured-PAHs, 14.1 and 8.2 micrograms/m3 for EC and in the subway 0.7 and 4.0 ng/m3 for benzol[a]pyrene, 30.2 and 67.5 ng/m3 for total PAHs, 109 and 6.9 micrograms/m3 for EC. A comparison between subway and car exposures shows significantly higher concentrations of PAHs in the subway train, which can be explained by relatively high concentrations of fluoranthene and pyrene in the subway. So far a satisfactory explanation has not been found, but one source might be the wooden railway ties which were formerly preserved with tar

How private car purchasing trends offset efficiency gains and the successful energy policy response

International Nuclear Information System (INIS)

O Gallachoir, Brian P.; Howley, Martin; Cunningham, Stephen; Bazilian, Morgan

2009-01-01

In 2006, energy-related CO 2 emissions from transport energy in Ireland were 168% above 1990 levels. Private cars were responsible for approx 45% of transport energy demand in 2006 (excluding fuel tourism). The average annual growth of new cars between 1990 and 2006 was 5.2%. This paper focuses on these new cars entering the private car fleet, in particular the purchasing trend towards larger size cars. This has considerably offset the improvements in the technical efficiency of individual car models. The analysis was carried out on the detailed data of each individual new vehicle entering the fleet in 2000-2006. The average CO 2 emissions per kilometre for new petrol cars entering the Irish fleet grew from 166 to 168 g CO 2 /km from 2000 to 2005 and reduced to 164 in 2006. For diesel cars the average reduced from 166 in 2000 to 161 in 2006. The paper also discusses how a recent change in vehicle registration taxation and annual motor tax had a significant impact purchasing trends by supporting lower emission vehicles. Cars with emissions up to 155 g CO 2 /km represented 41% of new private cars sold in Ireland in 2007 compared with 84% during the period July-November 2008.

Not fully charged: Welfare effects of tax incentives for employer-provided electric cars

NARCIS (Netherlands)

Dimitropoulos, A.; van Ommeren, J.N.; Koster, P.R.; Rietveld, P.

2016-01-01

More than 15 million cars are provided as fringe benefits by employers in Europe. The company car market is the driving force of changes in European car fleets and one of the main channels for the penetration of low emission vehicles. Policies in support of low emission vehicles through this channel

enviroCar - citizen science for sustainable traffic

Science.gov (United States)

Stasch, Christoph; Remke, Albert; Jirka, Simon; Nuest, Daniel

2015-04-01

Optimizing traffic flow is a challenging task, affecting both the mobility of people and the environment. Up to now, traffic monitoring is based on small samples using GPS devices or remote sensors such as cameras. Citizens are usually not actively involved in the process of collecting or analyzing traffic data. The enviroCar project (www.envirocar.org) aims at addressing this situation by providing an open platform that can be used by everyone to collect and analyze traffic-related data and thus to achieve sustainable traffic management by answering questions such as: How is the average speed on a certain route? Where are exceptionally long waiting times in front of traffic lights? At which crossings do more cars stop than drive through? Where are hotspots of fuel consumption and air pollutant emission during a certain time interval? In this presentation, an overview on the enviroCar project is given and current research challenges addressed in the context of the project are presented. Citizens are able to participate by registering at the enviroCar portal and downloading the enviroCar Android app. Once installed, the Android app allows citizens to collect car sensor data, e.g. speed, mass air flow, or intake temperature via an On-Board Diagnosis 2 (OBD-II) Adapter. After finishing a car ride, the data can be uploaded to the central enviroCar server where the data is anonymized and published as open data. Each enviroCar member has a profile page giving control on his own data and providing statistics on personal driving behavior. The portal also allows comparing personal statistics with the statistics of other members. It thus facilitates analysis whether, for example, a member is driving in a more fuel saving manner than other users. Besides only acting as a data collector, citizens can also explore the enviroCar data in online maps or download the data in standard formats for certain spatial areas and/or time intervals allowing them to conduct spatio

Auto-vehicles and environment: Emission limits and innovative technology

International Nuclear Information System (INIS)

Pinchera, G.

1992-01-01

Brief descriptions are given of the main design and performance characteristics and maintenance requirements of the principal types of catalytic converters currently being marketed in Italy. An assessment is made of the contribution of these devices to air pollution abatement in Italy as car owners conform to recently passed stricter emission limits. A historical review is made of trends in auto-vehicle pollution limits in the USA and Italy. Comparisons are made of efforts by industrialized countries to reduce air pollution in the transportation sector. Here, the author notes the slowness of Italy's response to the air pollution problem, in particular, this foreign-oil-dependent Nation's over-emphasis on energy consuming and highly polluting road transport systems, as well as, its lack of technology utilization and commercialization in the pollution equipment sector. Suggestions are made as to ways to overcome the worsening situation with regard to urban area traffic derived air pollution, e.g., the bolstering of mass transit systems and more R ampersand D investment in pollution abatement technologies

Influences of HVO and FAME on the combustion and emissions of modern passenger car diesel engines

International Nuclear Information System (INIS)

Stengel, Benjamin; Sadlowski, Thomas; Wichmann, Volker; Harndorf, Horst

2014-01-01

In the framework of this study engine tests were performed with FAME (fatty acid methyl ester) and HVO (hydrotreated vegetable oil) as straight fuels using a EURO-VI passenger car diesel engine. Standard diesel fuel (EN 590) was used as reference. To analyze the impacts of the biofuels on the combustion process the heat release rates were calculated from in-cylinder pressure measurements using a single-zone model. Furthermore emissions were measured and ECU data was recorded. Results from engine tests showed that both HVO and FAME positively affect the combustion by a decreased ignition delay due to its higher cetane number. Raw exhaust emissions of soot were clearly reduced with HVO while CO and THC emissions showed minor reductions. During FAME operation ECU control settings were shifted due to its lower heating value. FAME showed reductions of soot by 60 % which is caused by the fuel's oxygen content while NO x emissions where slightly increased. However, a fuel adapted ECU calibration could optimize, e.g., the injection timing and EGR to further reduce emissions. Tailpipe emissions were not affected by HVO and FAME as the exhaust aftertreatment systems worked similarly efficient for all three fuels.

Pathways to Decarbonise the European Car Fleet: A Scenario Analysis Using the Backcasting Approach

Directory of Open Access Journals (Sweden)

Arne Höltl

2017-12-01

Full Text Available This paper analyses decarbonisation scenarios for the European passenger car fleet in 2050. The scenarios have been developed using the backcasting approach and aim to reduce greenhouse gas (GHG emissions of passenger cars to a level defined in the Transport White paper that is 60% below 1990 levels. Considering the emission levels of 2010, a yearly reduction of 1.7% is required in order to achieve the target. Car emissions were decomposed into the main emission factors of mobility, efficiency and carbon intensity. How these factors change over time depends on various external factors: the pace of technological improvements, the future role of cars in society’s mobility system and the priority given to decarbonising energy demand. The analysis showed that if car mobility and ownership continue to increase as expected in a ‘business as usual’ case, a share of 97% plug-in hybrid or battery electric vehicles might be required by 2050, together with a substantial decrease in greenhouse gas emission from electricity production. A transition to more advanced car technology such as automated driving, advanced batteries or lightweight materials in vehicle production would raise vehicle efficiency. Should car mobility continue at a high level, an early technology transition will be required.

Cars, Cars, Cars

Science.gov (United States)

McIntosh, Phyllis

2013-01-01

Cars are the focus of this feature article, which explores such topics as the history of cars in the United States, the national highway system, safety and pollution concerns, mobility and freedom for women, classic car shows, and the road trip in American literature and film. Also included are links to the websites of Automobile in American Life…

Traffic generated non-exhaust particulate emissions from concrete pavement: A mass and particle size study for two-wheelers and small cars

Science.gov (United States)

Aatmeeyata; Kaul, D. S.; Sharma, Mukesh

This study aimed to understand the non-exhaust (NE) emission of particles from wear of summer tire and concrete pavement, especially for two wheelers and small cars. A fully enclosed laboratory-scale model was fabricated to simulate road tire interaction with a facility to collect particles in different sizes. A road was cast using the M-45 concrete mixture and the centrifugal casting method. It was observed that emission of large particle non exhaust emission (LPNE) as well as PM 10 and PM 2.5 increased with increasing load. The LPNE was 3.5 mg tire -1 km -1 for a two wheeler and 6.4 mg tire -1 km -1 for a small car. The LPNE can lead to water pollution through water run-off from the roads. The contribution of the PM 10 and PM 2.5 was smaller compared to the LPNE particles (less than 0.1%). About 32 percent of particle mass of PM 10 was present below 1 μm. The number as well as mass size distribution for PM 10 was observed to be bi-modal with peaks at 0.3 μm and 4-5 μm. The NE emissions did not show any significant trend with change in tire pressure.

Are stricter investment rules contagious? Host country competition for foreign direct investment through international agreements

OpenAIRE

Neumayer, Eric; Nunnenkamp, Peter; Roy, Martin

2014-01-01

We argue that the trend toward international investment agreements (IIAs) with stricter investment rules is driven by competitive diffusion, namely defensive moves of developing countries concerned about foreign direct investment (FDI) diversion in favor of competing host countries. Accounting for spatial dependence in the formation of bilateral investment treaties (BITs) and preferential trade agreements (PTAs) that contain investment provisions, we find that the increase in agreements with ...

Potential hazards of particulate noble metal emissions from car exhaust catalysts. Gefaehrdungspotential von partikulaeren Edelmetallemissionen aus Automobilabgas-Katalysatoren

Energy Technology Data Exchange (ETDEWEB)

Stoeber, W.

1985-01-01

The aim of the present bibliographical study is to investigate into the possibility of health impairment by emissions of eroded and particulate precious metals of catalytic converters for motor-car exhaust gas. Connected therewith is a survey of environmental pollution so far caused by platinum metals and of their biological impact. The risk estimation relates solely to the data on emission obtained during normal operation; research work is still needed with respect to the chemical composition, the size distribution and the particle forms of the precious metals emitted. Besides, only limited data are available as to the environmental behaviour of the precious metals.

Operation car for horizontal coke ovens. Bedienungswagen fuer waagrechte Verkokungsoefen

Energy Technology Data Exchange (ETDEWEB)

Kwasnik, H J; Piduch, H G

1981-07-30

An operation car which is driveable on the coke side of a coke oven battery is described. The operation car is equipped with a door lifter, a door and frame cleaner, a coke guiding grid and a collection hood for emissions developed on coke pushing. The car has a portal construction and it is driveable on both sides of the path of the coke receiving car. The operation has a considerable lower weight than usual cars. (HGOE).

49 CFR 210.29 - Operation standards (moving locomotives and rail cars).

Science.gov (United States)

2010-10-01

... cars). 210.29 Section 210.29 Transportation Other Regulations Relating to Transportation (Continued... REGULATIONS Inspection and Testing § 210.29 Operation standards (moving locomotives and rail cars). The operation standards for the noise emission levels of moving locomotives, rail cars, or consists of...

Steering levies on the purchase of new cars for the reduction of CO{sub 2} emissions; Lenkungsabgaben zur Senkung des CO{sub 2}-Ausstosses beim Neuwagenkauf. Hintergrund, Mechanismen, Prognosen

Energy Technology Data Exchange (ETDEWEB)

Haan, P. de; Mueller, M.; Peters, A.; Hauser, A.

2007-12-15

This comprehensive final report for the Swiss Federal Office of Energy (SFOE) takes a look at the background, mechanisms and prognoses for the reduction of CO{sub 2} emissions of new cars. This report focuses on policy measures - specifically the collection of budget-neutral so-called 'feebates' - that aim to influence the behaviour of buyers of new cars as a means of enhancing energy efficiency and reducing CO{sub 2} emissions. Both the European Union and Switzerland are pursuing a three-pillar strategy in which agreements with manufacturers and importers (pillar 1) are supplemented by the provision of more detailed information for customers in the form of energy labels for new vehicles as well as catalogues listing levels of fuel consumption (pillar 2). Pillar 3 concerns measures aimed at influencing car buying behaviour, generally based on the use of the energy label for new vehicles in order to realise the existing potentials for reducing CO{sub 2} emissions. The report takes a look at Switzerland's car market, buying behaviour, information on efficient vehicles, acceptance factors and incentive schemes. The findings of the study are presented and commented on.

EU limits for CO2 emissions of passenger cars. Roads to the 95 g/km target

Energy Technology Data Exchange (ETDEWEB)

Smokers, R.; Fraga, F.; Verbeek, M.; Bleuanus, S.; Sharpe, R.; Dekker, D.; Verbeek, R.; Willems, F.; Foster, D. [TNO, Delft (Netherlands); Hill, N.; Norris, J.; Brannigan, C. [AEA Technology plc, London (United Kingdom); Kampman, B.; Den Boer, E.; Van Essen, H. [CE Delft, Delft (Netherlands); Schilling, S.; Gruhlke, A. [Institut fuer Oekologie und Politik Oekopol, Hamburg (Netherlands); Breemersch, T.; De Ceuster, G.; Vanherle, K. [Transport and Mobility Leuven TML, Leuven (Belgium); Wrigley, S.; Owen, N.; Johnson, A. [Ricardo UK, Shoreham-by-Sea, West Sussex (United Kingdom); De Vleesschauwer, T.; Valla, V.; Anand, G. [IHS Global Insight, Nijmegen (Netherlands)

2012-02-15

The aim of this project is to support and advise the European Commission on options for lowering of the CO2 limit values of passenger cars and how they can be realised. The following main tasks were performed: (1) state-of-the-art vehicle emission reduction options for 2020; (2) evaluation of other utility parameters in addition to vehicle mass; (3) modalities for achieving 95 g/km; and (4) further aspects, including borrowing and banking of credits, life cycle aspects and rebound aspects.

Mode of transport to work, car ownership and CO{sub 2} emissions in Mauritius

Energy Technology Data Exchange (ETDEWEB)

Jaunky, V.C. (ETH Zuerich. Centre for Energy Policy and Economics, Zuerich (Switzerland)); Bundhoo, M.N.; Moco, S.Y. (Mauritius (Mauritius))

2011-05-15

Fast economical and demographic revolution in the small island developing state of Mauritius over the last decades has led to an unprecedented rise in private vehicle utilization. In this arena, the cognition of ongoing travel practices and their determinants is sine qua non. This paper examines the determinants of mode of transport, rise in car ownership and its related environmental impacts. We employ cross-section micro-data obtained from our household drop-off survey to estimate a multinomial logistic regression model of transport mode choice coupled with an exhaustive ordinary least squares analysis of carbon emissions. Empirical results indicate that factors such as travel time, expenses and time lost in traffic jam coupled with demographic and socio-economic characteristics such as age of individual and household income have profound upshots on transport mode decisions. On the other hand, fuel type, residential distance from work and age of individual displays statistically significant impacts on carbon dioxide emissions. (Author)

Carbon dioxide emission trends in cars and light trucks: A comparative analysis of emissions and methodologies for Florida's counties (2000 and 2008)

International Nuclear Information System (INIS)

Garren, S.J.; Pinjari, A.R.; Brinkmann, R.

2011-01-01

This paper investigates methodologies to quantify CO 2 emissions from cars and light trucks in Florida. The most widely used methodology to calculate greenhouse gas emissions in the transportation sector at the local level uses a harmonic average (HA) methodology based on nationally averaged fuel economies that assume 55% city and 45% highway VMTs. This paper presents a local condition (LC) methodology that accounts for county-level variations in city and highway VMTs, as opposed to assumed uniform driving conditions. Both HA and LC methodologies were used to estimate and compare absolute and per capita CO 2 emissions both statewide and counties for 2000 and 2008. From 2000 to 2008, statewide absolute and per capita CO 2 emissions increased similarly using HA and LC methodologies; however, the percent change varied considerably among counties. Statewide CO 2 emissions calculated from HA and LC methodologies differed by only -0.2% (2000) and 1.7% (2008); however, the differences in the county-level emissions ranged from -8.0% to 14.9% (2000) and from -5.6% to 17.0% (2008). While either the HA or the LC methodology yields a similar result statewide, significant variation exists at the county level, warranting the need to consider local driving conditions when estimating county-level emissions. - Highlights: → The paper evaluates GHG emission methods for on-road passenger vehicles in Florida. → The paper compares methods that assume the harmonic average with actual VMTs driven. → The paper analyzes statewide GHG emissions aggregated by county for 2000 and 2008. → The paper improves on methods that balance bottom-up with top-down GHG emissions.

-30 per cent EU-wide emission cut from the perspective of the Finnish economy; 30 prosentin vaehennystavoitteeseen siirtymisen energia- ja kansantaloudelliset vaikutukset

Energy Technology Data Exchange (ETDEWEB)

Honkatukia, J.; Koljonen, T.; Lehtilae, A.

2013-03-15

The Eu is considering the adoption of a tighter emission target, to replace the agreed -20 per cent emission target already agreed on. In this study, we analyze the implications of the proposed -30 per cent EU-wide emission cut from the perspective of the Finnish economy. We use an energy system model to study the technological choices and direct energy and investment costs of the stricter target, and an applied general equilibrium model to analyse its economic implications at industry and macroeconomic levels. We find that the stricter target increases the economic costs roughly proportionally to the abatement effort and consist mostly of the welfare losses of taxation. (orig.)

Energy Chain Analysis of Passenger Car Transport

Directory of Open Access Journals (Sweden)

Hans Jakob Walnum

2011-02-01

Full Text Available Transport makes up 20 percent of the World’s energy use; in OECD countries this has exceeded 30 percent. The International Energy Agency (IEA estimates that the global energy consumption will increase by 2.1 percent annually, a growth rate that is higher than for any other sector. The high energy consumption means that transportation accounts for nearly 30 percent of CO2 emission in OECD countries and is also one of the main sources of regional and local air pollution. In this article, we analyze energy consumption and greenhouse gas emissions from passenger car transport using an energy chain analysis. The energy chain analysis consists of three parts: the net direct energy use, the energy required for vehicle propulsion; the gross direct chain, which includes the net direct energy consumption plus the energy required to produce it; and, finally, the indirect energy chain, which includes the energy consumption for production, maintenance and operation of infrastructure plus manufacturing of the vehicle itself. In addition to energy consumption, we also analyze emissions of greenhouse gases measured by CO2-equivalents. We look at the trade-offs between energy use and greenhouse gas emissions to see whether some drivetrains and fuels perform favourable on both indicators. Except for the case of electric cars, where hydropower is the only energy source in the Norwegian context, no single car scores favourably on both energy consumption and greenhouse gas emissions.

CO_2 labelling of passenger cars in Europe: Status, challenges, and future prospects

International Nuclear Information System (INIS)

Haq, Gary; Weiss, Martin

2016-01-01

Directive 1999/94/EC requires Member States of the European Union (EU) to ensure that consumers are informed about the fuel consumption and CO_2 emissions of new passenger cars. The European Commission is currently evaluating the directive. In support of this effort, we assess the status of car labelling in the EU. We find that all EU Member States have formally implemented national car labelling schemes. However, relevant information is not presented to consumers in a uniform manner. Only 13 Member States have implemented graphic labels that differ in their design, metrics, and classification of vehicles. The fuel consumption data displayed to consumers underrate yearly fuel costs in the order of several hundred Euros per car. We argue that car labelling can be made more effective if Member States adopt: (i) a uniform label that mirrors, as far as feasible, the design of the EU energy label, (ii) data and classification metrics that accurately reflect the fuel consumption and CO_2 emissions observed by consumers, and (iii) a labelling scale that allows differentiation between efficient hybrid and plug-in hybrid vehicles. By following these recommendations, the European car labelling can receive wider recognition and foster well-informed consumer choices. - Highlights: •Car labelling Directive 1999/94 implemented by all 28 EU Member States. •National labelling schemes vary from each other in design and amount of information displayed to consumers. •Future revisions should ensure labelling accurately reflects on-road energy use and CO_2 emissions of cars. •Expansion of labelling scale toward zero CO_2 emissions would allow differentiating between hybrid and plug-in hybrid cars.

Demand for mini cars and large cars; decay effects, and gasoline demand in Japan

International Nuclear Information System (INIS)

Bonilla, David; Schmitz, Klaus E.; Akisawa, Atsushi

2012-01-01

This article explains why: (a) consumers underinvest in new car fuel economy by opting to buy large vehicles; (b) macro shifts in vehicle classes have occurred in the last decades; and how (c) the effects of vehicle fuel economy and shifts in vehicle type influence the growth path of gasoline demand, which is the key to designing effective energy efficiency goals for transport. From 2008, 1.9 EXJ (Exajoules) of energy were consumed in Japan by private vehicles producing 124 MtCO 2 emissions. For the period 1980 to 2008, we estimated: (1) gasoline demand for three vehicle sizes; (2) vehicle sales; (3) new car fuel economy changes (the ‘real’ technical change); and (4) vehicle stocks. Using a data sample for 1980–2008 we found that: (a) in the short term consumers buy fuel economy, that is sales of mini and small cars increase, but this is not sustained in the long term: and (b) consumers increasingly traded in their cars for larger cars. A further finding was that gasoline demand is projected to increase to 2.3 EXJ by 2035, even with a growing number of mini cars. The policy implication is clear: Japan’s policy to reduce oil dependency to 80% by 2030 is in peril as long as buyers prefer larger cars and drive ever longer distances.

Comparative engine performance and emission analysis of CNG and gasoline in a retrofitted car engine

International Nuclear Information System (INIS)

Jahirul, M.I.; Masjuki, H.H.; Saidur, R.; Kalam, M.A.; Jayed, M.H.; Wazed, M.A.

2010-01-01

A comparative analysis is being performed of the engine performance and exhaust emission on a gasoline and compressed natural gas (CNG) fueled retrofitted spark ignition car engine. A new 1.6 L, 4-cylinder petrol engine was converted to the computer incorporated bi-fuel system which operated with either gasoline or CNG using an electronically controlled solenoid actuated valve mechanism. The engine brake power, brake specific fuel consumption, brake thermal efficiency, exhaust gas temperature and exhaust emissions (unburnt hydrocarbon, carbon mono-oxide, oxygen and carbon dioxides) were measured over a range of speed variations at 50% and 80% throttle positions through a computer based data acquisition and control system. Comparative analysis of the experimental results showed 19.25% and 10.86% reduction in brake power and 15.96% and 14.68% reduction in brake specific fuel consumption (BSFC) at 50% and 80% throttle positions respectively while the engine was fueled with CNG compared to that with the gasoline. Whereas, the retrofitted engine produced 1.6% higher brake thermal efficiency and 24.21% higher exhaust gas temperature at 80% throttle had produced an average of 40.84% higher NO x emission over the speed range of 1500-5500 rpm at 80% throttle. Other emission contents (unburnt HC, CO, O 2 and CO 2 ) were significantly lower than those of the gasoline emissions.

Report on electric cars and plug-in hybrid cars; Redegoerelse - elbiler og plug-in hybridbiler

Energy Technology Data Exchange (ETDEWEB)

Elkjaer Toennesen, A.; Winther, K.; Noerregaard, K. (Teknologisk Institut, Taastrup (Denmark)); Larsen, Esben; Christensen, Linda; Kveiborg, O. (Danmarks Teknologiske Univ., Kgs. Lyngby (DTU) (Denmark))

2010-04-15

The Center for Green Transport at the Danish Transport Authority has prepared this statement in order to uncover driving technical aspects, user expectations and needs, and the environmental consequences of using electric and plug-in hybrid cars. An electric car is defined as a car driven by an electric motor that has a battery that can be charged with power from the grid. A plug-in hybrid car is defined as a car that combines gasoline or diesel engine with an electric motor with a battery which can be recharged with power from the grid. From an overall consideration related to the transport sector electric cars and plug-in hybrid cars have the major advantage that negative impacts on environment and climate from traffic can be reduced while the high mobility is maintained. Through an increased use of electric cars and plug-in hybrid cars, the many advantages attached to the car as an individual transportation form is maintained, while CO{sub 2} emissions etc. are reduced. Electric cars and plug-in hybrid cars is one of the technologies that are considered to have particularly great prospects in the medium term when it comes to promoting new technologies in transport. Another advantage of using electric vehicles is the power supply factor. An increased use of electricity in transport will reduce the need for and dependence on fossil fuels in the sector. Both electric cars and plug-in hybrid cars are expected to be used for storage of wind power, a possibility which is hardly available today. The plug-in hybrid car could meet some of the challenges facing the pure electric car, because it also can use conventional fuel. The report presents analyses based on three focus areas: a) Users' needs, expectations and economics in relation to vehicles; b) The technology - and hence the manufacturers' opportunities and challenges; c) Connection to the power grid. (ln)

Trends in Aggregate Vehicle Emissions: Do We Need To Emissions Test?

OpenAIRE

Matthew Kahn

1995-01-01

Vehicle emissions are falling. As the oldest vehicles in the fleet are scrapped and are replaced by cleaner vehicles, aggregate emissions decline. Given this trend, must costly used car regulation continue? The Clean Air Act of 1990 requires more stringent used car testing without considering the counter-factual of how aggregate emissions would evolve in the absence of more regulation. This paper use data on vehicle scrappage rates, vehicle emissions by model year, and county air quality leve...

On-board measurement of emissions from liquefied petroleum gas, gasoline and diesel powered passenger cars in Algeria.

Science.gov (United States)

Chikhi, Saâdane; Boughedaoui, Ménouèr; Kerbachi, Rabah; Joumard, Robert

2014-08-01

On-board measurements of unit emissions of CO, HC, NOx and CO₂ were conducted on 17 private cars powered by different types of fuels including gasoline, dual gasoline-liquefied petroleum gas (LPG), gasoline, and diesel. The tests performed revealed the effect of LPG injection technology on unit emissions and made it possible to compare the measured emissions to the European Artemis emission model. A sequential multipoint injection LPG kit with no catalyst installed was found to be the most efficient pollutant reduction device for all of the pollutants, with the exception of the NOx. Specific test results for a sub-group of LPG vehicles revealed that LPG-fueled engines with no catalyst cannot compete with catalyzed gasoline and diesel engines. Vehicle age does not appear to be a determining parameter with regard to vehicle pollutant emissions. A fuel switch to LPG offers many advantages as far as pollutant emissions are concerned, due to LPG's intrinsic characteristics. However, these advantages are being rapidly offset by the strong development of both gasoline and diesel engine technologies and catalyst converters. The LPG's performance on a chassis dynamometer under real driving conditions was better than expected. The enforcement of pollutant emission standards in developing countries is an important step towards introducing clean technology and reducing vehicle emissions. Copyright © 2014. Published by Elsevier B.V.

Effects of fresh lubricant oils on particle emissions emitted by a modern gasoline direct injection passenger car.

Science.gov (United States)

Pirjola, Liisa; Karjalainen, Panu; Heikkilä, Juha; Saari, Sampo; Tzamkiozis, Theodoros; Ntziachristos, Leonidas; Kulmala, Kari; Keskinen, Jorma; Rönkkö, Topi

2015-03-17

Particle emissions from a modern turbocharged gasoline direct injection passenger car equipped with a three-way catalyst and an exhaust gas recirculation system were studied while the vehicle was running on low-sulfur gasoline and, consecutively, with five different lubrication oils. Exhaust particle number concentration, size distribution, and volatility were determined both at laboratory and on-road conditions. The results indicated that the choice of lubricant affected particle emissions both during the cold start and warm driving cycles. However, the contribution of engine oil depended on driving conditions being higher during acceleration and steady state driving than during deceleration. The highest emission factors were found with two oils that had the highest metal content. The results indicate that a 10% decrease in the Zn content of engine oils is linked with an 11-13% decrease to the nonvolatile particle number emissions in steady driving conditions and a 5% decrease over the New European Driving Cycle. The effect of lubricant on volatile particles was even higher, on the order of 20%.

Fuel prices, emission standards, and generation costs for coal vs natural gas power plants.

Science.gov (United States)

Pratson, Lincoln F; Haerer, Drew; Patiño-Echeverri, Dalia

2013-05-07

Low natural gas prices and stricter, federal emission regulations are promoting a shift away from coal power plants and toward natural gas plants as the lowest-cost means of generating electricity in the United States. By estimating the cost of electricity generation (COE) for 304 coal and 358 natural gas plants, we show that the economic viability of 9% of current coal capacity is challenged by low natural gas prices, while another 56% would be challenged by the stricter emission regulations. Under the current regulations, coal plants would again become the dominant least-cost generation option should the ratio of average natural gas to coal prices (NG2CP) rise to 1.8 (it was 1.42 in February 2012). If the more stringent emission standards are enforced, however, natural gas plants would remain cost competitive with a majority of coal plants for NG2CPs up to 4.3.

Analysis of CO2 emissions and of the other characteristics of the European market of new passenger cars. 3. Brands analysis

International Nuclear Information System (INIS)

Zervas, Efthimios

2010-01-01

This article analyses the engine and vehicle characteristics and CO 2 emissions of the new passenger cars for the thirteen major brands of the European market. As in the first two articles of this work, the target is to find the real market parameters influencing exhaust CO 2 emissions. This analysis is focused on the sales distribution of the major brands, EU average and within each country, and four main parameters of each brand having an impact on CO 2 emissions: average vehicle weight, average engine capacity, average maximum and specific power. The average CO 2 emissions of each brand on the new European driving cycle and its urban and extra urban parts are examined at the last part of this article.

Refueling emissions from cars in Japan: Compositions, temperature dependence and effect of vapor liquefied collection system

Science.gov (United States)

Yamada, Hiroyuki; Inomata, Satoshi; Tanimoto, Hiroshi

2015-11-01

Refueling emissions from cars available on the Japanese market, which were not equipped with specific controlling devices, were investigated. For the composition analysis, a proton transfer reaction plus switchable reagent ion mass spectrometry (PTR + SRI-MS), which is capable of real-time measurement, was used. In addition, the performance of a vapor liquefied collection system (VLCS), which is a recently developed controlling device, was evaluated and compared with an onboard refueling vapor recovery (ORVR) system. The refueling emission factor of uncontrolled vehicles at 20 °C was 1.02 ± 0.40 g/L in the case dispensing 20 L of fuel. The results of composition analysis indicated that the maximum incremental reactivity (MIR) of refueling emissions in Japan was 3.49 ± 0.83. The emissions consist of 80% alkanes and 20% alkenes, and aromatics and di-enes were negligible. C4 alkene had the highest impact on the MIR of refueling emissions. The amounts of refueling emissions were well reproduced by a function developed by MOVE2010 in the temperature range of 5-35 °C. The compositions of the refueling emissions varied in this temperature range, but the change in MIR was negligible. The trapping efficiency of VLCS was the same level as that of the ORVR (over 95%). The MIRs of refueling and evaporative emissions were strongly affected by that of the test fuel. This study and our previous study indicated that MIRbreakthrough ≈ MIRrefueling ≈ MIRfuel + 0.5 and MIRpermeation ≈ MIRfuel. The real-world estimated average MIRfuel in Japan was about 3.0.

Analysis of the CO2 emissions and of the other characteristics of the European market of new passenger cars. 2. Segment analysis

International Nuclear Information System (INIS)

Zervas, Efthimios

2010-01-01

This article analyzes the engine and vehicle characteristics and the CO 2 emissions of the new passenger cars for all segments of the European market. As in the first article of this work, the target is to find the real market parameters influencing exhaust CO 2 emissions. The present analysis is focused on the segment sales distribution (EU average and within each country) and also in four parameters of each segment influencing CO 2 emissions: average vehicle weight, average engine capacity, average maximum and specific power. The second part of this work concerns the CO 2 emissions of each segment on the New European Driving Cycle and its urban and extra urban parts.

Driving Cars by Means of Genetic Algorithms

OpenAIRE

Sáez Achaerandio, Yago; Pérez, Diego; Sanjuan, Óscar; Isasi Viñuela, Pedro

2008-01-01

Proceedings of: 10th International Conference on Parallel Problem Solving From Nature, PPSN 2008. Dortmund, Germany, September 13-17, 2008 The techniques and the technologies supporting Automatic Vehicle Guidance are an important issue. Automobile manufacturers view automatic driving as a very interesting product with motivating key features which allow improvement of the safety of the car, reducing emission or fuel consumption or optimizing driver comfort during long journeys. Car raci...

47 CFR 78.103 - Emissions and emission limitations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Emissions and emission limitations. 78.103... CABLE TELEVISION RELAY SERVICE Technical Regulations § 78.103 Emissions and emission limitations. (a) A CARS station may be authorized to employ any type of emission, for which there are technical standards...

Car MAX-DOAS measurements around entire cities: quantification of NOx emissions from the cities of Mannheim and Ludwigshafen (Germany

Directory of Open Access Journals (Sweden)

U. Platt

2010-06-01

Full Text Available We present car Multi-Axis (MAX- DOAS observations of tropospheric NO2 carried out on circles around the cities of Mannheim and Ludwigshafen (Germany on 24 August 2006. Together with information on wind speed and direction, the total emissions of the encircled source(s are quantified from these measurements. In contrast to recent similar studies based on zenith scattered sun light (elevation angle of 90°, we use a MAX-DOAS instrument mounted on a car, which observes scattered sun light under different elevation angles (here 45°, and 90°. Compared to simple zenith sky observations, MAX-DOAS observations have higher sensitivity and reduced uncertainty, and avoid systematic offsets in the determination of the vertically integrated trace gas concentration. The determination of the absolute value of the integrated tropospheric trace gas concentrations is especially important for the calculation of absolute trace gas fluxes through arbitrary transects. However, even if emission sources are completely surrounded, systematic offsets in the measured vertically integrated trace gas concentration can lead to errors in the determined total emissions, especially for observations around extended areas. In this study we discuss and quantify different error sources. In most cases, the largest error source is the variability and imperfect knowledge of the wind field. In addition – depending on the trace species observed - also chemical transformations between the emission sources and the measurement location have to be considered. For that purpose we use local observations within the encircled area to quantify and/or correct these errors. From our observations we derive a total NOx emission from the Mannheim/Ludwigshafen area of (7.4±1.8×1024 molec/sec, which if assumed to be constant throughout the year would correspond to a total emission of 17 830±4340 t/yr (calculated with the mass of NO2 t/yr, consistent with existing emission estimates. From our

Emission concepts for future passenger car diesel engines; Emissionskonzepte fuer zukuenftige Pkw-Dieselmotoren

Energy Technology Data Exchange (ETDEWEB)

Krueger, M.; Wiartalla, A.; Lichtenberg, T.; Koerfer, T. [FEV Motorentechnik, Aachen (Germany)

2003-07-01

In order to keep the current success of the Diesel powered passenger cars also for the future, intensive development effort is absolutely necessary in the near future. A special challenge is presented by the already confirmed or discussed future emission standards. However, every chance must be taken to keep the fuel consumption of the diesel engine respectively diesel powered vehicle on the lowest possible level. In front of this background measures concerning combustion system development as well as exhaust gas aftertreatment are analyzed in this report with respect to their influence on emission reduction and fuel consumption. It can be summarized, that still a significant emission reduction potential exists for the passenger car diesel engine. However, fulfilling the next step of emission legislation, getting effective after 2005, only by combustion system improvement, seems to be a difficult way to go from todays point of view. Especially with respect to fuel consumption, an efficient combination of combustion improvement and exhaust gas aftertreatment represents a more promising solution for the future. Most important for a successful realisation of such an approach will be the overall power consumption of the exhaust gas aftertreatment device. This does also include the thermomanagement of the engine and exhaust gas system as well as the energy losses due to the regeneration demands of the discontinuously working NO{sub x}-and particulate trap. Considering this last issue, a fuel additive as particulate trap regeneration aid as well as the fuel sulphur content respectively the sulphur sensitivity of the NO{sub x}-trap will play a significant role in the future. (orig.) [German] Um den Erfolg des Diesel-Pkw's auch zukuenftig sicherzustellen, sind intensive Entwicklungsarbeiten notwendig. Eine besondere Herausforderung stellen die zukuenftig zu erfuellenden Emissionsanforderungen dar. Dabei muessen alle moeglichen Massnahmen ergriffen werden, um den

The taxation of diesel cars in Belgium – revisited

International Nuclear Information System (INIS)

Mayeres, Inge; Proost, Stef

2013-01-01

This paper compares the current taxation of diesel and gasoline cars in Belgium with the guidelines for optimal taxation. We find that diesel cars are still taxed much less than gasoline cars, resulting in a dominant market share for diesel cars in the car stock. If the fuel tax is the main instrument to control for externalities and generate revenues, the diesel excise should be much higher than the excise on gasoline for two reasons: diesel is more polluting than gasoline and more importantly, through the better fuel efficiency, diesel cars contribute less fiscal revenues per mile. - Highlights: ► With a correct tax system the diesel excise should be higher than that on gasoline. ► When this is difficult, the fixed annual charge should be higher for diesel cars. ► The current tax structure for gasoline and diesel cars in Belgium is suboptimal. ► It implies that CO 2 emissions are reduced, but in a very cost-inefficient way

The contribution to the greenhouse effect by passenger cars and heating is increasing

International Nuclear Information System (INIS)

Bouchereau, J.M.

2000-12-01

Between 1990 and 1998, the domestic sector contribution to the greenhouse effect increased from 25 % to 27 %. During this period, there was a 20 % rise in greenhouse gas emissions from passenger cars. These emissions amounted to 20 million tonnes of carbon equivalent out of a total of 175 million tonnes in 1998 (all sectors taken together). Carbon dioxide emissions from the tertiary sector increased by 2,3 % annually between 1980 and 1998, particularly as a result of increased road freight transport. Although technological progress has been made on fuel consumption of vehicles, greater use of passenger cars combined with decreasing running costs has led to gross emissions in France being 2 % more in 1998 than in 1990. In 1998, the transport sector (passenger cars and freight transport) was responsible for three-quarters of this increase. (author)

Effects of low concentration biodiesel blends application on modern passenger cars. Part 2: Impact on carbonyl compound emissions

International Nuclear Information System (INIS)

Fontaras, Georgios; Karavalakis, Georgios; Kousoulidou, Marina; Ntziachristos, Leonidas; Bakeas, Evangelos; Stournas, Stamoulis; Samaras, Zissis

2010-01-01

Today in most European member states diesel contains up to 5% vol biodiesel. Since blending is expected to increase to 10% vol, the question arises, how this higher mixing ratio will affect tailpipe emissions particularly those linked to adverse health effects. This paper focuses on the impact of biodiesel on carbonyl compound emissions, attempting also to identify possible relationship between biodiesel feedstock and emissions. The blends were produced from five different feedstocks, commonly used in Europe. Measurements were conducted on a Euro 3 common-rail passenger car over various driving cycles. Results indicate that generally the use of biodiesel at low concentrations has a minor effect on carbonyl compound emissions. However, certain biodiesels resulted in significant increases while others led to decreases. Biodiesels associated with increases were those derived from rapeseed oil (approx. 200%) and palm oil (approx. 180%), with the highest average increases observed at formaldehyde and acroleine/acetone. - Biodiesel application, may increase the levels of certain pollutants such as carbonyl compounds which are associated with both environmental and health risks.

The direct and indirect CO_2 rebound effect for private cars in China

International Nuclear Information System (INIS)

Zhang, Yue-Jun; Liu, Zhao; Qin, Chang-Xiong; Tan, Tai-De

2017-01-01

The quantity of China's private cars has increased dramatically in the past decade, which has become one of the key sources of carbon emission and air pollution in the cities of China. In theory, to improve energy efficiency can reduce carbon emission significantly, but the result may be affected by the rebound effect. This paper utilizes a two-stage Almost Ideal Demand System (AIDS) model to estimate the total CO_2 rebound effect for China's private cars during 2001–2012 at the provincial level, then uses a panel data model to analyze its impact factors. The results suggest that, first of all, the CO_2 emissions of private cars have the super conservation effect, partial rebound effect and backfire effect among provinces in China. And the direct CO_2 rebound effect plays a dominant role in the total CO_2 rebound effect in most provinces. Second, the total CO_2 rebound effect of private cars among China's provinces presents an overall convergence trend over time. Finally, the household expenditure and the population density have a negative and positive influence on the total CO_2 rebound effect for China's private cars, respectively. - Highlights: • Private cars have become the key source of carbon emission in China. • This paper employs a two-stage Almost Ideal Demand System (AIDS) model • The direct and indirect CO_2 rebound effects for China's private cars are estimated. • The direct CO_2 rebound effect plays a dominant role in the total CO_2 rebound effect in most provinces. • The total CO_2 rebound effect among China's provinces has a convergence over time.

ARE PRICING POLICIES EFFECTIVE TO CHANGE CAR USE?

Directory of Open Access Journals (Sweden)

Geertje SCHUITEMA

2007-01-01

Results revealed that under pricing policies most people did not intend to change their car use. Pricing policies were relatively more effective when prices increased significantly. Especially visiting and shopping trips were affected, while commuting trips were hardly affected. Moreover, respondents were most likely to reduce their car use for short trips, which are an important source of CO2 emissions and local air pollution.

The electric car controversy. A social-constructivist interpretation of the California zero-emission vehicle mandate

Energy Technology Data Exchange (ETDEWEB)

Fogelberg, H

1998-07-01

This study focuses the socio-technical dynamics of the attempted reintroduction of electric cars in California. The underlying question is whether or not it is possible to open up an entrenched technological area as car technology, and achieve a radical change. With the perspectives of social constructivist approaches to technological change, this study examines how a large technological controversy was initiated by regulatory action of the air agency in California, the California Air Resources Board, how this controversy developed and stabilized, and how it was ended by the air agency and the auto industry. Based on mainly secondary sources, the definitions that were established on electric cars and gasoline cars at the turn of the 20th century are highlighted, thus showing the existence of two types of automobiles: the city car and the endurance car. The city car did not survive, and was not defined as being a real car. Based on mainly primary sources, the recent electric car controversy is examined, suggesting that the air agency could not force the car industry to re-introduce the city car, and consequently the efforts were directed towards the development of more advanced batteries that could give the electric car a performance close to that of the gasoline car. It also display that electric car technology was enhanced due to the mandate. In ending the controversy, the agency, due to political forces, changed from 'command-and-control' to a 'partnership' strategy. The California Air Resources Board postponed the mandate (from 1998 to 2003), due to the fact that large volume production of advanced batteries was not expected to be in place by 1998. This regulatory relief removed the principal obstacle on behalf of auto manufacturers of not to accept mandated markets, and led General Motors to start to market their purpose built electric sports car by late 1996, and Toyota to promote electric- and electric hybrid car technologies. Thus car technology was re-opened.

The electric car controversy. A social-constructivist interpretation of the California zero-emission vehicle mandate

Energy Technology Data Exchange (ETDEWEB)

Fogelberg, H.

1998-07-01

This study focuses the socio-technical dynamics of the attempted reintroduction of electric cars in California. The underlying question is whether or not it is possible to open up an entrenched technological area as car technology, and achieve a radical change. With the perspectives of social constructivist approaches to technological change, this study examines how a large technological controversy was initiated by regulatory action of the air agency in California, the California Air Resources Board, how this controversy developed and stabilized, and how it was ended by the air agency and the auto industry. Based on mainly secondary sources, the definitions that were established on electric cars and gasoline cars at the turn of the 20th century are highlighted, thus showing the existence of two types of automobiles: the city car and the endurance car. The city car did not survive, and was not defined as being a real car. Based on mainly primary sources, the recent electric car controversy is examined, suggesting that the air agency could not force the car industry to re-introduce the city car, and consequently the efforts were directed towards the development of more advanced batteries that could give the electric car a performance close to that of the gasoline car. It also display that electric car technology was enhanced due to the mandate. In ending the controversy, the agency, due to political forces, changed from 'command-and-control' to a 'partnership' strategy. The California Air Resources Board postponed the mandate (from 1998 to 2003), due to the fact that large volume production of advanced batteries was not expected to be in place by 1998. This regulatory relief removed the principal obstacle on behalf of auto manufacturers of not to accept mandated markets, and led General Motors to start to market their purpose built electric sports car by late 1996, and Toyota to promote electric- and electric hybrid car technologies. Thus car

Emission Characteristics for a Homogeneous Charged Compression Ignition Diesel Engine with Exhaust Gas Recirculation Using Split Injection Methodology

Directory of Open Access Journals (Sweden)

Changhee Lee

2017-12-01

Full Text Available Due to the serious issues caused by air pollution and global warming, emission regulations are becoming stricter. New technologies that reduce NOx and PM emissions are needed. To cope with these social exhaust gas regulation demands, many advanced countries are striving to develop eco-friendly vehicles in order to respond to stricter emissions regulations. The homogeneous charged compression ignition engine (HCCI incorporates a multi-stage combustion engine with multiple combustion modes, catalyst, direct fuel injection and partial mixing combustion. In this study, the HCCI combustion was applied to analyze and review the results of engines applying HCCI combustion without altering the conventional engine specifications. The optimization of exhaust gas recirculation (EGR and compression ratio changes provides an optimal fuel economy. In this study, potential for optimum economy within the range of IMEP 0.8 MPa has been evaluated.

Electric vehicles in China: emissions and health impacts.

Science.gov (United States)

Ji, Shuguang; Cherry, Christopher R; J Bechle, Matthew; Wu, Ye; Marshall, Julian D

2012-02-21

E-bikes in China are the single largest adoption of alternative fuel vehicles in history, with more than 100 million e-bikes purchased in the past decade and vehicle ownership about 2× larger for e-bikes as for conventional cars; e-car sales, too, are rapidly growing. We compare emissions (CO(2), PM(2.5), NO(X), HC) and environmental health impacts (primary PM(2.5)) from the use of conventional vehicles (CVs) and electric vehicles (EVs) in 34 major cities in China. CO(2) emissions (g km(-1)) vary and are an order of magnitude greater for e-cars (135-274) and CVs (150-180) than for e-bikes (14-27). PM(2.5) emission factors generally are lower for CVs (gasoline or diesel) than comparable EVs. However, intake fraction is often greater for CVs than for EVs because combustion emissions are generally closer to population centers for CVs (tailpipe emissions) than for EVs (power plant emissions). For most cities, the net result is that primary PM(2.5) environmental health impacts per passenger-km are greater for e-cars than for gasoline cars (3.6× on average), lower than for diesel cars (2.5× on average), and equal to diesel buses. In contrast, e-bikes yield lower environmental health impacts per passenger-km than the three CVs investigated: gasoline cars (2×), diesel cars (10×), and diesel buses (5×). Our findings highlight the importance of considering exposures, and especially the proximity of emissions to people, when evaluating environmental health impacts for EVs.

On-road measurement of NH3 emissions from gasoline and diesel passenger cars during real world driving conditions

Science.gov (United States)

Suarez-Bertoa, Ricardo; Mendoza-Villafuerte, Pablo; Riccobono, Francesco; Vojtisek, Michal; Pechout, Martin; Perujo, Adolfo; Astorga, Covadonga

2017-10-01

NH3 is a precursor of PM2.5 which deteriorates urban air quality, affects human health and impacts the global radiation budget. Since vehicles are important sources of NH3 in urban areas, we have satisfactorily studied the possibility of measuring NH3 emissions from gasoline and SCR-equipped diesel light-duty vehicles during real driving on-road operation using a portable FTIR. The performance of the portable FTIR resulted to be comparable to that of a laboratory-based FTIR during a series of experiments performed in the Vehicle Emission Laboratory (VELA) using the World-harmonized Light-duty Test Cycle (WLTC). Higher on-road NH3 emission factors were obtained for the gasoline vehicle than for the diesel. High NOx emissions were measured from the diesel vehicle, indicating a low efficiency of the DeNOx system, SCR. On-road NH3 emission factors were ∼2 times lower than during the laboratory tests at 23 °C for both vehiclesNH3 emissions were not observed for the diesel vehicle during cold start operation. However, NH3 cold start emissions from the gasoline vehicle were up to 2 orders of magnitude higher than during the entire road trips, ranging from 45 to 134 mg km-1. Cold start emissions are of paramount importance as they commonly take place in urban areas. Hence, future urban reductions in PM2.5 might need to take into consideration the introduction of NH3 emissions limits for passenger cars.

Car ownership and use taxes as pollution correcting instruments

DEFF Research Database (Denmark)

Mabit, Stefan Lindhard; Mulalic, Ismir

There have been many attempts to alter the taxation of private vehicles to obtain more energy-efficient car transport. The last significant reform in Denmark was completed in 2007. The most important objective was to improve fuel efficiency and consequently to reduce emissions related to car tran...... a change in car taxes. Based on a simple theoretical framework we use a large sample of detailed Danish data to estimate the joint demand for vehicles and kilometres. The empirical results point at effects that have important implications....

Stimulated Emission Pumping Enablling Sub-Diffraction-Limited Spatial Resolution in CARS Microscopy

NARCIS (Netherlands)

Cleff, C.; Gross, P.; Fallnich, C.; Offerhaus, Herman L.; Herek, Jennifer Lynn; Kruse, K.; Beeker, W.P; Beeker, W.P.; Lee, Christopher James; Boller, Klaus J.; Dobner, S.

2012-01-01

Suppression of CARS signal generation is demonstrated by equalization of the ground and Raman states via a control state in a theoretical investigation. Using donut-shaped control light fields for population transfer results in sub-diffraction-limited spatial resolution CARS microscopy.

Controlling fugitive emissions from mechanical seals

International Nuclear Information System (INIS)

Adams, W.V.

1992-01-01

This paper reports that enactment of the 1990 Federal Clean Air Amendments will sharply focus efforts in the process industries to reduce fugitive emissions. Moreover, state and local governments may be imposing stricter laws and regulations which will affect allowable fugitive emissions from U.S. refineries and process plants. Plants outside the U.S. have similar concerns. Clearly, mechanical seals for process pumps represent an enormous population and is one category of equipment destined for careful evaluation as a means to control fugitive emissions. Fugitive are unintentional emissions from valves, pumps, flanges, compressors, etc., as opposed to point-source emissions from stacks, vents and flares. Fugitive emissions do not occur as a part of normal plant operations, but result from the effects of: Malfunctions, Age, Lack of proper maintenance, Operator error, Improper equipment specification, Use of inferior technology, and externally caused damage

CO{sub 2} emissions from future cars in the Nordic countries - including analysis of the effect on the power system of 500.000 electric cars in the Nordic countries; CO{sub 2} udledning fra fremtidens personbiler i Norden - med delanalyse af betydningen for el-systemet af 500.000 el-biler i Norden

Energy Technology Data Exchange (ETDEWEB)

2011-01-15

Detailed calculations of the power system in Scandinavia and Germany in 2020 are made, including the countries' known and specific plans for CO{sub 2} reduction and increased use of renewable energy. The calculations analyzed three scenarios for how increased electric power consumption pulls investments in the power sector by 2020. It is shown that only if the countries through grants schemes and other incentives directly link increased consumption of electricity for electric vehicles with greater demands for investments in renewable energy, the CO{sub 2} emissions from electric vehicles will decrease significantly. Such a direct linkage is assessed not to become the case with the existing frame-work and objectives of the EU countries and Norway. The average of the more detailed calculations show a CO{sub 2} emission from electric cars in 2020 of just 650 g CO{sub 2}/kWh (excluding upstream emissions), which is about 10% lower than previously estimated. Towards 2020 increased efficiency of conventional cars (diesel) will probably be a cheaper way to achieve CO{sub 2} reductions in the transport sector than through an expansion with a larger number of electric cars. If oil prices rise to around $ 150/barrel or more, while the price of batteries for electric vehicles drops significantly in the period, this will result, however, is challenged. The same costs are assumed for development and production of diesel and electric cars. For electric cars there will be additional costs for batteries and charging infrastructure. The on manufacturers' pricing strategies for different types of cars have not been considered. The report demonstrates that it will very likely be more expensive to reduce CO{sub 2} emissions from transport compared with, for example the costs in electric power and heat producing sectors that are subject to EU quota system. It can therefore be considered whether a larger part of the EU's reduction goals in the next 10-20 years should be

Gasoline reformulation to reduce exhaust emissions in Finnish conditions. Influence of sulphur and benzene contents of gasoline on exhaust emissions

International Nuclear Information System (INIS)

Kytoe, M.; Aakko, P.; Lappi, M.

1994-01-01

At earlier stages of the study it was found that the exhaust emissions from cars are reduced when using fuels with no more than 4 wt% of oxygen. At this stage of the study the work focused on impacts of the sulphur and benzene content of gasoline on exhaust emissions in Finland. Sulphur in gasoline retards the operation of the catalyst, and consequently the exhaust emissions of catalyst cars increase if the sulphur content of the fuel increases. In the present study, evaporation during refuelling were measured for fuels with varying vapour pressures and benzene contents of gasoline. The total hydrocarbon evaporation was reduced by 22 % (10 g) when the vapour pressure of gasoline was reduced from 85 kPa to 65 kPa. Correspondingly, benzene evaporation during refuelling was reduced to a third when the benzene content of the fuel was reduced from the level of 3 wt% to 1 wt%. The reduction of the sulphur content of gasoline from 500 ppm to 100 ppm affected regulated exhaust emissions from the catalyst car at +22 deg C as follows: CO emission was reduced on average by 14 % (0.175 g/km), CH emission by 7 % (0.010 g/km) and NO x emission by 9 % (0.011 g/km). At-7 deg C the percentual changes were smaller. When the benzene content of the fuel was reduced from 3 wt% to 1 wt%, the benzene emission from the catalyst cars was reduced by 20-30 % and from the non-catalyst cars on average by 30 % both at +22 deg C and -7 deg C. The benzene emission ranged 3-22 mg/km for the catalyst cars and 40-90 mg/km for the non-catalyst cars at +22 deg C in the FTP test

An evaluation of the hybrid car technology for the Mexico Mega City

Science.gov (United States)

Jazcilevich, Aron D.; Reynoso, Agustin Garcia; Grutter, Michel; Delgado, Javier; Ayala, Ulises Diego; Lastra, Manuel Suarez; Zuk, Miriam; Oropeza, Rogelio Gonzalez; Lents, Jim; Davis, Nicole

The introduction of hybrid electric vehicle (HEV) technology in the private car fleet of Mexico City is evaluated in terms of private costs, energy, public health and CO 2 emission benefits. In addition to constructing plausible scenarios for urban expansion, emission, car fleet, and fuel consumption for year 2026 and comparing them with a 2004 base case, a time series is built to obtain accumulated economic benefits. Experimental techniques were used to build a vehicle library for a car simulator that included a Prius 2002, chosen as the HEV technology representative for this work. The simulator is used to estimate the emissions and fuel consumption of the car fleet scenarios. In the context of an urban scenario for year 2026, a complex air quality model obtains the concentrations of criterion pollutants corresponding to these scenarios. Using a technology penetration model, the hybridized fleet starts unfolding in year 2009 reaching to 20% in 2026. In this year, the hybridized fleet resulted in reductions of about 10% of CO 2 emissions, and yielded reductions in daytime mean concentrations of up to 7% in ozone and 3.4% in PM 2.5 compared to the 2004 base case. These reductions are concentrated in the densely populated areas of Mexico City. By building a time series of costs and benefits it is shown that, depending on fuel prices and using a 5% return rate, positive accumulated benefits (CO 2 benefits + energy benefits + public health benefits - private costs) will start generating in year 2015 reaching between 2.8 and 4.5 billion US Dlls in 2026. Another modernized private fleet consisting exclusively of Tier I and II cars did not yield appreciable results, signaling that a change in private car technology towards HEV's is needed to obtain significant accumulated benefits.

Economic and environmental evaluation of compressed-air cars

International Nuclear Information System (INIS)

Creutzig, Felix; Kammen, Daniel M; Papson, Andrew; Schipper, Lee

2009-01-01

Climate change and energy security require a reduction in travel demand, a modal shift, and technological innovation in the transport sector. Through a series of press releases and demonstrations, a car using energy stored in compressed air produced by a compressor has been suggested as an environmentally friendly vehicle of the future. We analyze the thermodynamic efficiency of a compressed-air car powered by a pneumatic engine and consider the merits of compressed air versus chemical storage of potential energy. Even under highly optimistic assumptions the compressed-air car is significantly less efficient than a battery electric vehicle and produces more greenhouse gas emissions than a conventional gas-powered car with a coal intensive power mix. However, a pneumatic-combustion hybrid is technologically feasible, inexpensive and could eventually compete with hybrid electric vehicles.

The effect on road load due to variations in valid coast down tests for passenger cars

NARCIS (Netherlands)

Mensch, P. van; Ligterink, N.E.; Cuelenaere, R.F.A.

2014-01-01

Real-world CO2 emissions of passenger cars very often deviate from the Type Approval value. The Type Approval value for CO2 emissions of passenger cars is based on a chassis dynamometer test in a laboratory. The total vehicle resistance of a vehicle, or 'road load', is simulated on the chassis

Cleaning the Diesel Engine Emissions

DEFF Research Database (Denmark)

Christensen, Thomas Budde

This paper examines how technologies for cleaning of diesel emission from road vehicles can be supported by facilitating a technology push in the Danish automotive emission control industry. The European commission is at present preparing legislation for the euro 5 emission standard (to be enforced...... in 2010). The standard is expected to include an 80% reduction of the maximum particulate emissions from diesel cars. The fulfillment of this requirement entails development and production of particulate filters for diesel cars and trucks. Theoretically the paper suggests a rethinking of public industry...

Global carbon benefits of material substitution in passenger cars until 2050 and the impact on the steel and aluminum industries.

Science.gov (United States)

Modaresi, Roja; Pauliuk, Stefan; Løvik, Amund N; Müller, Daniel B

2014-09-16

Light-weighting of passenger cars using high-strength steel or aluminum is a common emissions mitigation strategy. We provide a first estimate of the global impact of light-weighting by material substitution on GHG emissions from passenger cars and the steel and aluminum industries until 2050. We develop a dynamic stock model of the global car fleet and combine it with a dynamic MFA of the associated steel, aluminum, and energy supply industries. We propose four scenarios for substitution of conventional steel with high-strength steel and aluminum at different rates over the period 2010-2050. We show that light-weighting of passenger cars can become a "gigaton solution": Between 2010 and 2050, persistent light-weighting of passenger cars can, under optimal conditions, lead to cumulative GHG emissions savings of 9-18 gigatons CO2-eq compared to development business-as-usual. Annual savings can be up to 1 gigaton per year. After 2030, enhanced material recycling can lead to further reductions: closed-loop metal recycling in the automotive sector may reduce cumulative emissions by another 4-6 gigatons CO2-eq. The effectiveness of emissions mitigation by material substitution significantly depends on how the recycling system evolves. At present, policies focusing on tailpipe emissions and life cycle assessments of individual cars do not consider this important effect.

Influence of driving cycles on exhaust emissions and fuel consumption of gasoline passenger car in Bangkok.

Science.gov (United States)

Nutramon, Tamsanya; Supachart, Chungpaibulpatana

2009-01-01

The influence of different driving cycles on their exhaust emissions and fuel consumption rate of gasoline passenger car was investigated in Bangkok based on the actual measurements obtained from a test vehicle driving on a standard chassis dynamometer. A newly established Bangkok driving cycle (BDC) and the European driving cycle (EDC) which is presently adopted as the legislative cycle for testing automobiles registered in Thailand were used. The newly developed BDC is constructed using the driving characteristic data obtained from the real on-road driving tests along selected traffic routes. A method for selecting appropriate road routes for real driving tests is also introduced. Variations of keyed driving parameters of BDC with different driving cycles were discussed. The results showed that the HC and CO emission factors of BDC are almost two and four times greater than those of EDC, respectively. Although the difference in the NOx emission factor is small, the value from BDC is still greater than that of EDC by 10%. Under BDC, the test vehicle consumes fuel about 25% more than it does under EDC. All these differences are mainly attributed to the greater proportion of idle periods and higher fluctuations of vehicle speed in the BDC cycle. This result indicated that the exhausted emissions and fuel consumption of vehicles obtained from tests under the legislative modal-type driving cycle (EDC) are significantly different from those actually produced under real traffic conditions especially during peak periods.

CuseCar--community car-sharing program : car sharing lessons learned.

Science.gov (United States)

2011-08-01

CuseCar of Syracuse launched services in December 2008 with 3 Toyota Prius Hybrids. CuseCar initially, due to : concerns about availability, limited membership to Origination Sponsor Locations, which in turn developed few : members. In 2009 CuseCar o...

Study on Emission Measurement of Vehicle on Road Based on Binomial Logit Model

OpenAIRE

Aly, Sumarni Hamid; Selintung, Mary; Ramli, Muhammad Isran; Sumi, Tomonori

2011-01-01

This research attempts to evaluate emission measurement of on road vehicle. In this regard, the research develops failure probability model of vehicle emission test for passenger car which utilize binomial logit model. The model focuses on failure of CO and HC emission test for gasoline cars category and Opacity emission test for diesel-fuel cars category as dependent variables, while vehicle age, engine size, brand and type of the cars as independent variables. In order to imp...

Are tax exemptions for electric cars an efficient climate policy measure?

OpenAIRE

Geir H. Bjertnæs

2013-01-01

This study finds that the welfare gain, excluding environmental effects, generated by increasing the Norwegian tax rate on purchase of electric cars from 8 to 37 percent amounts to approximately 5500- 6500 NOK (or 680-820 euro) per ton increase in GHG emissions in the long run. Substantial tax exemptions implies that reallocation from electric cars towards petrol and diesel powered cars generates a tax revenue gain of more than 40 billion NOK, which amounts to almost 10 percent of government ...

On-road emissions of CO, CO2 and NOX from four wheeler and emission estimates for Delhi.

Science.gov (United States)

Jaiprakash; Habib, Gazala; Kumar, Anil; Sharma, Akash; Haider, Minza

2017-03-01

This study presents the emission factor of gaseous pollutants (CO, CO 2 , and NO X ) from on-road tailpipe measurement of 14 passenger cars of different types of fuel and vintage. The trolley equipped with stainless steel duct, vane probe velocity meter, flue gas analyzer, Nondispersive infra red (NDIR) CO 2 analyzer, temperature, and relative humidity (RH) sensors was connected to the vehicle using a towing system. Lower CO and higher NO X emissions were observed from new diesel cars (post 2010) compared to old cars (post 2005), which implied that new technological advancement in diesel fueled passenger cars to reduce CO emission is a successful venture, however, the use of turbo charger in diesel cars to achieve high temperature combustion might have resulted in increased NO X emissions. Based on the measured emission factors (g/kg), and fuel consumption (kg), the average and 95% confidence interval (CI) bound estimates of CO, CO 2 , and NO X from four wheeler (4W) in Delhi for the year 2012 were 15.7 (1.4-37.1) , 6234 (386-12,252) , and 30.4 (0.0-103) Gg/year, respectively. The contribution of diesel, gasoline and compressed natural gas (CNG) to total CO, CO 2 and NO X emissions were 7:84:9, 50:48:2 and 58:41:1 respectively. The present work indicated that the age and the maintenance of vehicle both are important factors in emission assessment therefore, more systematic repetitive measurements covering wide range of vehicles of different age groups, engine capacity, and maintenance level is needed for refining the emission factors with CI. Copyright © 2016. Published by Elsevier B.V.

Psychological determinants of fuel consumption of purchased new cars

OpenAIRE

Peters, A; Gutscher, H; Scholz, R W

2011-01-01

With regard to reducing fuel consumption and CO2 emissions of road transport consumers' adoption of fuel-efficient vehicles is crucial. However, facing the ongoing trend of increasing car size and power, fuel consumption is apparently of lesser importance to most buyers. For the design of effective measures to change behavior and promote fuel-efficient cars, psychological factors should be considered. Drawing from psychological research on environmental behavior, we propose a model which inte...

Evolution of traffic emissions in European urban areas: Milan case study

International Nuclear Information System (INIS)

Giugliano, M.; Cemin, A.; Cernuschi, S.

1992-01-01

The worldwide increasing role of mobile sources on the air quality of urban areas requires a careful evaluation of all the potential intervention policies for the reduction of traffic related emissions. The accurate description of the evolution of the source, following the renewal of the fleet with vehicles regulated by stricter emission standards, represents the basic premise for this evaluation. This paper outlines a proposed methodology for the evaluation of the trend of mobile source emissions, implemented on the calculation program EMISMOB, and reports the results obtained with its application to predict the evolution of traffic emissions in the urban area of Milan (Italy) until the year 2010

Biofuel mandate versus favourable taxation of electric cars. The case of Norway

OpenAIRE

Geir H. Bjertnæs

2013-01-01

This study investigates whether biofuel policies or favourable taxation of electric cars should be employed to satisfy a green house gas emission target connected to private transport within the Norwegian economy. The study shows that implementation of biofuel generates a welfare gain in the presence of the current favourable taxation of electric cars in Norway. Implementation of biofuels, however, generates a welfare loss when the tax rate on purchase of electric cars is increased to the ave...

Integrated assessment of energy efficiency technologies and CO_2 abatement cost curves in China’s road passenger car sector

International Nuclear Information System (INIS)

Peng, Bin-Bin; Fan, Ying; Xu, Jin-Hua

2016-01-01

Highlights: • Energy efficiency technologies in Chinese passenger cars are classified in detail. • CO_2-reduction potential and abatement cost are analyzed for technology bundles. • Marginal abatement cost curve is established from both micro and macro perspectives. • Spark ignition, diesel and hybrid electric vehicle paths should be firstly promoted. • Technology promotion should start from the area of taxies and high-performance cars. - Abstract: Road transport is one of the main sources of energy consumption and CO_2 emissions. It is essential to conserve energy and reduce emissions by promoting energy efficiency technologies (EETs) in this sector. This study first identifies EETs for the passenger cars and then classifies them into various technology bundles. It then analyzes the CO_2-reduction potentials and emissions abatement costs of 55 type-path, 246 type-path-technology, and 465 type-path-subtechnology bundles from micro-vehicular and macro-industrial perspectives during 2010–2030, based on which marginal abatement cost (MAC) curve for China’s road passenger car sector is established. Results show that the cumulative CO_2-reduction potential of EETs on passenger cars in China during 2010–2030 is about 2698.8 Mt, but only 4% is cost-effective. The EETs with low emissions abatement costs are mainly available in the spark ignition (SI), diesel, and hybrid electric vehicle (HEV) paths on the taxis and high-performance cars, and also in the transmission, vehicle body and SI technologies on the private cars, which could be promoted at present. The technologies with large emissions reduction potential are mainly available in the plug-in hybrid electric vehicle (PHEV) and electric vehicle (EV) paths, which would be the main channels for reducing carbon emissions in the long run.

Secondary Organic Aerosol Production from Gasoline Vehicle Exhaust: Effects of Engine Technology, Cold Start, and Emission Certification Standard.

Science.gov (United States)

Zhao, Yunliang; Lambe, Andrew T; Saleh, Rawad; Saliba, Georges; Robinson, Allen L

2018-02-06

Secondary organic aerosol (SOA) formation from dilute exhaust from 16 gasoline vehicles was investigated using a potential aerosol mass (PAM) oxidation flow reactor during chassis dynamometer testing using the cold-start unified cycle (UC). Ten vehicles were equipped with gasoline direct injection engines (GDI vehicles) and six with port fuel injection engines (PFI vehicles) certified to a wide range of emissions standards. We measured similar SOA production from GDI and PFI vehicles certified to the same emissions standard; less SOA production from vehicles certified to stricter emissions standards; and, after accounting for differences in gas-particle partitioning, similar effective SOA yields across different engine technologies and certification standards. Therefore the ongoing, dramatic shift from PFI to GDI vehicles in the United States should not alter the contribution of gasoline vehicles to ambient SOA and the natural replacement of older vehicles with newer ones certified to stricter emissions standards should reduce atmospheric SOA levels. Compared to hot operations, cold-start exhaust had lower effective SOA yields, but still contributed more SOA overall because of substantially higher organic gas emissions. We demonstrate that the PAM reactor can be used as a screening tool for vehicle SOA production by carefully accounting for the effects of the large variations in emission rates.

How much do incentives affect car purchase? Agent-based microsimulation of consumer choice of new cars. Part 2. Forecasting effects of feebates based on energy-efficiency

International Nuclear Information System (INIS)

Haan, Peter de; Mueller, Michel G.; Scholz, Roland W.

2009-01-01

In this paper, we simulate the car market in order to forecast the effects of feebate systems based on an energy-labeling scheme using categories A to G. Very fuel-efficient (A) cars receive a cash incentive, highly inefficient (G) cars pay additional fees. Consumers have different price elasticities and behavioral options to react to feebates. They can switch to a smaller sized car, but as energy-efficiency varies widely within size segments, they can also stick to the preferred size class and choose a more efficient (smaller) engine. In addition, previously owned cars influence the next car to be chosen. We use an agent-based microsimulation approach particularly suited to predict environmental and market effects of feebates. Heteorogeneous agents choose from a choice set drawn from a detailed fleet of new cars. Incentives of EUR2000 for A-labeled cars induce an additional rated CO 2 emission decrease of new car registrations between 3.4% and 4.3%, with CO 2 abatement costs between EUR6 and EUR13 per ton, and otherwise little undesired market disturbance. The risk of rebound effects is estimated to be low. After adopting the frequencies of consumer segments to a given country, the model presented is applicable to all European car markets. (author)

The Impact of Tax Reform on New Car Purchases in Ireland

NARCIS (Netherlands)

Hennessy, H.; Tol, R.S.J.

2011-01-01

We examine the impact of recent tax reforms in Ireland on private car transport and its greenhouse gas emissions. A carbon tax was introduced on fuels, and purchase (vehicle registration) and ownership (motor) taxes were switched from engine size to potential emissions. We use a demographic model of

European type-approval test procedure for evaporative emissions from passenger cars against real-world mobility data from two Italian provinces.

Science.gov (United States)

Martini, Giorgio; Paffumi, Elena; De Gennaro, Michele; Mellios, Giorgos

2014-07-15

This paper presents an evaluation of the European type-approval test procedure for evaporative emissions from passenger cars based on real-world mobility data. The study relies on two large databases of driving patterns from conventional fuel vehicles collected by means of on-board GPS systems in the Italian provinces of Modena and Firenze. Approximately 28,000 vehicles were monitored, corresponding to approximately 36 million kilometres over a period of one month. The driving pattern of each vehicle was processed to derive the relation between trip length and parking duration, and the rate of occurrence of parking events against multiple evaporative cycles, defined on the basis of the type-approval test procedure as 12-hour diurnal time windows. These results are used as input for an emission simulation model, which calculates the total evaporative emissions given the characteristics of the evaporative emission control system of the vehicle and the ambient temperature conditions. The results suggest that the evaporative emission control system, fitted to the vehicles from Euro 3 step and optimised for the current type-approval test procedure, could not efficiently work under real-world conditions, resulting in evaporative emissions well above the type-approval limit, especially for small size vehicles and warm climate conditions. This calls for a revision of the type-approval test procedure in order to address real-world evaporative emissions. Copyright © 2014. Published by Elsevier B.V.

Using in-car feedback to influence travel decisions

Energy Technology Data Exchange (ETDEWEB)

Byrne, I T [WS Atkins plc, Dublin (Ireland); O' Mahony, M M; Broderick, B M [Trinity College, Dublin (Ireland). Dept. of Civil, Structural and Environmental Engineering

1999-11-01

It is widely accepted that there is a need to reduce private car use, thereby alleviating congested urban areas and reducing fuel consumption and emissions from transport vehicles. This paper examines one approach to achieving this aim, based on the hypothesis that car owners do not correctly perceive the full cost of a car trip. The primary objective of the research was to assess the potential for correcting this misperception through the use of a digital car running-cost meter, installed on the dashboard of a car, which displays on a real-time basis the cost of each trip. Cost meter information on marginal trip cost, external cost and the effect of driving style was provided to a sample of drivers in a small pilot action in Dublin. The findings from the data (diaries and interviews) are presented and extrapolated by means of a transport network model to assess potential energy saving. The key findings from the work are as follows. (a) There was a significant reduction in off-peak-period trips observed as a result of the car meter but there was no significant reduction in time spent in the car, distance travelled by car and cost of driving. (b) A surprising finding from the project was that 40% of the subjects who happened to be changing their vehicle shortly after being involved in the project chose more fuel-efficient vehicles. They attributed their choice in part to their increased awareness of fuel costs as a result of their involvement in the project. (author)

Data-driven analysis of the effectiveness of evaporative emissions control systems of passenger cars in real world use condition: Time and spatial mapping

Science.gov (United States)

De Gennaro, Michele; Paffumi, Elena; Martini, Giorgio

2016-03-01

This paper assesses the effectiveness of the evaporative emissions control systems of European passenger cars on the basis of real-world activity data. The study relies on two large datasets of driving patterns from conventional fuel vehicles collected by means of on-board GPS systems, consisting of 4.5 million trips and parking events recorded by monitoring 28,000 vehicles over one month. Real world evaporative emissions are estimated using a model that associates a carbon canister desorption event to each trip and a fuel vapour generation event to each parking. The mass of volatile organic compounds released into the air is calculated taking into account the hot-soak, permeation and breathing emission mechanisms. The analysis is based on 36 scenarios, defined by varying the climate conditions, the fuel vapour pressure, the tank material, the tank headspace volume, the purging volume flow rate and the mass of the activated carbon contained in the canister. The results show that in May 4 out of the 18 scenarios considered for Modena and 6 out of the 18 scenarios considered for Firenze lead to evaporative emissions values above the current type approval limit (i.e. 2 [g/day] per vehicle). In July, these numbers increase to 10 out of the 18 scenarios for Modena and to 12 out of the 18 scenarios for Firenze. Looking at the fleet distribution a share of approximately 20% of the fleet is characterised by evaporative emissions higher than the limit in May, increasing to 48% in July, with a peak value of 98%. The emission peak value is estimated to be approximately 4 [g/day] in May and 8 [g/day] in July, while the time-dependent results show emission rates up to nearly 15 [g/s] in Modena and 30 [g/s] in Firenze, with a respective cumulative value in July up to 0.4 and 0.8 tons of VOCs per day. The space-dependent results show a value of the emissions in July of approximately 4-to-8 [kg/km2/day] in the city areas. These results confirm previous findings from the authors

Velocity-dependent emission factors of benzene, toluene and C 2-benzenes of a passenger car equipped with and without a regulated 3-way catalyst

Science.gov (United States)

Heeb, Norbert V.; Forss, Anna-Maria; Bach, Christian; Mattrel, Peter

Time-resolved chemical ionization mass spectrometry (CI-MS) has been used to investigate the velocity-dependent emission factors for benzene, toluene, the C 2-benzenes (xylenes and ethyl benzene) and nitrogen monoxide of a gasoline-driven passenger car (1.4 l, model year 1995) driven with or without catalytic exhaust gas treatment. A set of seven different driving cycles - including the European Driving Cycle (EDC), the US Urban (FTP 75) and the Highway driving cycles - with a total driving time of 12,000 s have been studied. From the obtained emission data, two sets of 15,300 and 17,200 data points which represent transient driving in the velocity range of 0-150 km h -1 and in an acceleration window of -2-3 m s -2 were explored to gain velocity-dependent emission factors. The passenger car, equipped with a regulated rhodium-platinum based three-way catalyst, showed optimal conversion efficiency (>95%) for benzene in the velocity range of 60-120 km h -1. The conversion of benzene was reduced (speed and engine load (>130 km h -1). Whereas the conversion efficiency for the class of C 2-benzenes was reduced to 10%, no net conversion could be found for toluene and benzene when driven above 130 km h -1. In contrast, the benzene and toluene emissions exceeded those of the untreated exhaust gas in the velocity range of 130-150 km h -1 by 50-92% and by 10-34%, respectively. Thus, benzene and toluene were formed across the examined three-way catalyst if the engine is operated for an extended time in a fuel-rich mode (lambda<1).

Green cars and biofuels. How is Sweden affected by the EU directives?; Miljoebilar och biodrivmedel - Hur paaverkas Sverige av EU:s direktiv?

Energy Technology Data Exchange (ETDEWEB)

Kaageson, Per

2007-07-15

During spring 2007, the EU commission presented preliminary outlines of three directives on means for reducing carbon dioxide emission from the transportation sector: Biofuels should make up 10% of the transportation fuel volume by year 2020; the Life-cycle emission of greenhouse gases from transportation fuels should be reduced by 1% per energy unit per year between 2010 and 2020; New passenger cars should, on average, not emit more than 130 g CO{sub 2}/km by year 2012 irrespective of fuel. The directives constitute challenges for Sweden, since Swedish cars have the highest fuel consumption in Europe, and since Sweden backs production of biofuels without special regards for the emission from cultivation and processing. The fuel suppliers will probably concentrate on low-level mixing of biofuels into gasoline and diesel, and on DME, biogas and electric plug-in units and battery cars. The commission proposes that ethanol could be mixed up to 10% into gasoline. The suppliers will, if possible, look for ethanol and biodiesel produced with low emissions. Natural gas could be attractive since it lowers the greenhouse gas emissions by 20-30%. Fuels from coal and oil shales will correspondingly be disadvantaged. It will probably not be possible to continue to exempt biofuels from taxes in Sweden, since the new life cycle requirement will complicate this policy. Furthermore, in the long run there are no valid reasons for society to exempt biofuels from taxes that are used for covering the costs for road maintenance, accidents, emissions and noise. The present Swedish governmental green car definition, allowing CO{sub 2} emissions up to 2118 g/km for cars that can use biofuels will be an obstacle for reaching the 2012 goal of 130 g/km. Even if EU chooses a flexible legislation where CO{sub 2} emissions rights can be traded, it will be necessary to rework the Swedish regulations and green car subsidies in order to support the development towards smaller and more fuel

Analysis of non-regulated vehicular emissions by extractive FTIR spectrometry: tests on a hybrid car in Mexico City

Science.gov (United States)

Reyes, F.; Grutter, M.; Jazcilevich, A.; González-Oropeza, R.

2006-07-01

A methodology to acquire valuable information on the chemical composition and evolution of vehicular emissions is presented. The analysis of the gases is performed by passing a constant flow of a sample gas from the tail-pipe into a 10 L multi-pass cell. The absorption spectra within the cell are obtained using an FTIR spectrometer at 0.5 cm-1 resolution along a 13.1 m optical path. Additionally, the total flow from the exhaust is continuously measured from a differential pressure sensor on a Pitot tube installed at the exit of the exhaust. This configuration aims to obtain a good speciation capability by coadding spectra during 30 s and reporting the emission (in g/km) of key and non-regulated pollutants, such as CO2, CO, NO, SO2, NH3, HCHO, NMHC, during predetermined driving routines. The advantages and disadvantages of increasing the acquisition frequency, as well as the effect of other parameters such as spectral resolution, cell volume and flow rate, are discussed. With the aim of testing and evaluating the proposed technique, experiments were performed on a dynamometer running FTP-75 and typical driving cycles of the Mexico City Metropolitan Area (MCMA) on a Toyota Prius hybrid vehicle. This car is an example of recent automotive technology to reach the market dedicated to reduce emissions and therefore pressing the need of low detection techniques. This study shows the potential of the proposed technique to measure and report in real time the emissions of a large variety of pollutants, even from a super ultra-low emission vehicle (SULEV). The emissions of HC's, NOx, CO and CO2 obtained here are similar to experiments performed in other locations with the same vehicle model. Some differences suggest that an inefficient combustion process and type of gasoline used in the MCMA may be partly responsible for lower CO2 and higher CO and NO emission factors. Also, a fast reduction of NO emission to very low values is observed after cold ignition, giving rise to

Prospects for electric cars: electric vehicle impact assessment study. Final report, 15 December 1975--30 April 1978

Energy Technology Data Exchange (ETDEWEB)

Hamilton, W.

1978-11-01

The characteristics of future electric cars were projected by means of parametric models of weight, cost, and performance. They included urban ranges as much as two to four times those of recent electric cars: up to 150 km for improved lead-acid batteries, 250 km for nickel-zinc batteries, and 450 km for lithium-sulfur batteries. From data tapes of major travel surveys in Los Angeles and Washington, these ranges were found to be sufficient for most needs of all three major groups of drivers: secondary and primary drivers at multi-driper households, and drivers at one-driver households. Even with the longest design ranges, however, the electric cars would be incapable of occasional long trips now made by conventional cars, and only at the shortest design ranges would they be competitive in cost. Through modeling of supply and demand for over 200 U.S. utilities it was projected that, by the year 2000, almost 60% of US cars could be electrified, only 17% of the recharging power would come from petroleum. Modeling of air pollutant emissions for 24 large urban regions showed that electrification of all cars would reduce regional hydrocarbons and carbon monoxide emissions by roughly half, but increase sulfur oxide emissions some 20%. Traffic noise would be significantly reduced, even after major quieting of conventional vehicles. Identified resources of battery materials suffice for tens of millions of electric cars, but not necessarily for complete electrification of all US autos. Economic impacts aside from added costs for motorists would be relatively minor.

Multi-year remote-sensing measurements of gasoline light-duty vehicle emissions on a freeway ramp

International Nuclear Information System (INIS)

Sjoedin, A.; Andreasson, K.

2000-01-01

On-road optical remote-sensing measurements of gasoline light-duty vehicle (LDV) emissions - CO, HC, NO - were conducted on a freeway ramp in Gothenburg, Sweden, in 1991, 1995 and 1998. Based on almost 30,000 emission measurements, the results show that both catalyst cars and non-catalyst cars emissions deteriorate over time, but also that the emission performance of new TWC-cars has improved significantly in recent years. Furthermore, it was found that fleet age rather than model year determines the rate of emission deterioration for TWC-cars for both CO and NO. The study demonstrates that remote sensing may constitute a powerful tool to evaluate real-world LDV emissions; however, daily field calibration procedures need to be developed in order to assure that the evolution in fleet average emissions can be accurately measured. (author)

Pollutant emissions from vehicles with regenerating after-treatment systems in regulatory and real-world driving cycles.

Science.gov (United States)

Alvarez, Robert; Weilenmann, Martin; Novak, Philippe

2008-07-15

Regenerating exhaust after-treatment systems are increasingly employed in passenger cars in order to comply with regulatory emission standards. These systems include pollutant storage units that occasionally have to be regenerated. The regeneration strategy applied, the resultant emission levels and their share of the emission level during normal operation mode are key issues in determining realistic overall emission factors for these cars. In order to investigate these topics, test series with four cars featuring different types of such after-treatment systems were carried out. The emission performance in legislative and real-world cycles was monitored as well as at constant speeds. The extra emissions determined during regeneration stages are presented together with the methodology applied to calculate their impact on overall emissions. It can be concluded that exhaust after-treatment systems with storage units cause substantial overall extra emissions during regeneration mode and can appreciably affect the emission factors of cars equipped with such systems, depending on the frequency of regenerations. Considering that the fleet appearance of vehicles equipped with such after-treatment systems will increase due to the evolution of statutory pollutant emission levels, extra emissions originating from regenerations of pollutant storage units consequently need to be taken into account for fleet emission inventories. Accurately quantifying these extra emissions is achieved by either conducting sufficient repetitions of emission measurements with an individual car or by considerably increasing the size of the sample of cars with comparable after-treatment systems.

Energy saving and CO2 mitigation through restructuring Jordan's transportation sector: The diesel passenger cars scenario

International Nuclear Information System (INIS)

Al-Hinti, I.; Al-Ghandoor, A.; Akash, B.; Abu-Nada, E.

2007-01-01

The transportation sector is responsible for 37% of the total final energy consumption in Jordan, with passenger cars taking a share of 57% in this sector. Improvement of the energy efficiency of the transportation sector can help in alleviating socio-economic pressures resulting from the inflating fuel bill and in lowering the relatively high CO 2 emission intensity. Current legislations mandate that all passenger cars operating in Jordan are to be powered with spark ignition engines using gasoline fuel. This paper examines potential benefits that can be achieved through the introduction of diesel cars to the passenger cars market in Jordan. Three scenarios are suggested for implementation and investigated with a forecasting model on the basis of local and global trends over the period 2007-2027. It is demonstrated that introducing diesel passenger cars can slow down the growth of energy consumption in the transportation sector resulting in significant savings in the national fuel bill. It is also shown that this is an effective and feasible option for cutting down CO 2 emissions

Societal lifecycle costs of cars with alternative fuels/engines

International Nuclear Information System (INIS)

Ogden, Joan M.; Williams, Robert H.; Larson, Eric D.

2004-01-01

Effectively addressing concerns about air pollution (especially health impacts of small-particle air pollution), climate change, and oil supply insecurity will probably require radical changes in automotive engine/fuel technologies in directions that offer both the potential for achieving near-zero emissions of air pollutants and greenhouse gases and a diversification of the transport fuel system away from its present exclusive dependence on petroleum. The basis for comparing alternative automotive engine/fuel options in evolving toward these goals in the present analysis is the 'societal lifecycle cost' of transportation, including the vehicle first cost (assuming large-scale mass production), fuel costs (assuming a fully developed fuel infrastructure), externality costs for oil supply security, and damage costs for emissions of air pollutants and greenhouse gases calculated over the full fuel cycle. Several engine/fuel options are considered--including current gasoline internal combustion engines and a variety of advanced lightweight vehicles: internal combustion engine vehicles fueled with gasoline or hydrogen; internal combustion engine/hybrid electric vehicles fueled with gasoline, compressed natural gas, Diesel, Fischer-Tropsch liquids or hydrogen; and fuel cell vehicles fueled with gasoline, methanol or hydrogen (from natural gas, coal or wind power). To account for large uncertainties inherent in the analysis (for example in environmental damage costs, in oil supply security costs and in projected mass-produced costs of future vehicles), lifecycle costs are estimated for a range of possible future conditions. Under base-case conditions, several advanced options have roughly comparable lifecycle costs that are lower than for today's conventional gasoline internal combustion engine cars, when environmental and oil supply insecurity externalities are counted--including advanced gasoline internal combustion engine cars, internal combustion engine

Comparison of methods to assess cost-effectiveness of CO2 policies for cars

International Nuclear Information System (INIS)

Van den Brink, R.M.M.; Annema, J.A.

2007-01-01

The purchase of smaller more fuel-efficient cars seems to have only advantages: the purchase results in less carbon dioxide (CO2) emissions and the purchaser spends less money on the car and the fuel. In spite of this a general trend in buying more fuel-efficient cars is hardly observable in the Netherlands. This report argues that the reason is that consumers value other things in cars (size, comfort, status) next to out-of-pocket money they have to spend on purchase, taxes and fuels. This report recommends to estimating cost-effectiveness of CO2 policies for cars with methods including benefit losses related to buying other cars - smaller, less comfortable - compared to the reference case. This approach results in more realistic cost estimates of CO2 policies compared to methods, which are limited to a 'narrow' - only out-of-pocket money - cost concept [nl

Electric cars: technical characteristics and environmental impacts

Energy Technology Data Exchange (ETDEWEB)

Helmers, Eckard; Marx, Patrick [Trier University of Applied Sciences, Birkenfeld (Germany). Institut fuer Angewandtes Stoffstrommanagement (IfaS)

2012-12-15

Electric vehicles have been identified as being a key technology in reducing future emissions and energy consumption in the mobility sector. The focus of this article is to review and assess the energy efficiency and the environmental impact of battery electric cars (BEV), which is the only technical alternative on the market available today to vehicles with internal combustion engine (ICEV). Electricity onboard a car can be provided either by a battery or a fuel cell (FCV). The technical structure of BEV is described, clarifying that it is relatively simple compared to ICEV. Following that, ICEV can be 'e-converted' by experienced personnel. Such an e-conversion project generated reality-close data reported here. Practicability of today's BEV is discussed, revealing that particularly small-size BEVs are useful. This article reports on an e-conversion of a used Smart. Measurements on this car, prior and after conversion, confirmed a fourfold energy efficiency advantage of BEV over ICEV, as supposed in literature. Preliminary energy efficiency data of FCV are reviewed being only slightly lower compared to BEV. However, well-to-wheel efficiency suffers from 47% to 63% energy loss during hydrogen production. With respect to energy efficiency, BEVs are found to represent the only alternative to ICEV. This, however, is only true if the electricity is provided by very efficient power plants or better by renewable energy production. Literature data on energy consumption and greenhouse gas (GHG) emission by ICEV compared to BEV suffer from a 25% underestimation of ICEV-standardized driving cycle numbers in relation to street conditions so far. Literature data available for BEV, on the other hand, were mostly modeled and based on relatively heavy BEV as well as driving conditions, which do not represent the most useful field of BEV operation. Literature data have been compared with measurements based on the converted Smart, revealing a distinct GHG emissions

EVALUATING THE DIFFUSION OF FUEL-CELL CARS IN THE CHINA MARKETS

OpenAIRE

RITS, Vincent; KYPREOS, Socrates; WOKAUN, Alexander

2004-01-01

Air pollution is a major problem in many of China's cities, with SO2, NOx and PM emissions exceeding World Health Organisation's air quality standards. The environmental (dis-) performance of Chinese vehicles contributes largely to this problem. The fuel-cell system represents a technology that could eliminate much of the local air-pollution problem. However, the chances of fuel-cell cars during the next decades are still highly questioned. In this research, the diffusion of fuel-cell cars...

How clean are Europe's cars? An analysis of carmaker progress towards EU CO2 targets in 2009

Energy Technology Data Exchange (ETDEWEB)

Dings, J. (ed.)

2010-11-15

This report is the fifth T and E has published on the annual progress Europe's major car manufacturers have made in reducing CO2 emissions and fuel consumption of new cars. The main purpose of these reports is to assess the progress that major car manufacturers in Europe are making towards cutting the average CO2 emissions of their products. We also assess how each carmaker is positioned to hit the mandatory CO2 standards that the European Union has set for 2015. In this year's report, we add an analysis showing to what extent the CO2 reductions achieved can be attributed to the financial crisis i.e. sales of cheaper, smaller cars, and to what extent to technological improvements.

Increasing fuel efficiency of passenger cars with the “climate-control” system as a method of improving the ecological safety of the urban infrastructure

Science.gov (United States)

Burakova, L. N.; Burakova, A. D.; Burakova, O. D.; Dovbysh, V. O.

2018-01-01

Motor vehicle should provide safety and a high ecological standard of living for the population. One of the methods to improve the ecological friendliness of motor vehicles in particular passenger cars (cars), which are considered in this article, is the growth of their fuel economy. It is established that fuel consumption and the amount of specific emissions of harmful substances with exhaust gases of cars when using the “climate control” system depend on the effective ambient temperature, the color of the opaque car body elements, the power of the car engine and the interior volume. However, the simplest controlled factor is the color of the opaque car body elements, which is characterized by the coefficient of light reflection. In the course of experimental studies, we established the dependences of a change in fuel consumption and a share of reducing emissions of harmful substances with exhaust gases of passenger cars with the “climate control” system on the coefficient of light reflection. A method has been developed to reduce fuel consumption and the amount of specific emissions of harmful substances with the exhaust gases of passenger cars when using the “climate control” system, which involves painting the vehicle roof white and allows reducing fuel consumption by 5.5-10.3% and the amount of specific emissions of harmful substances by 0.37-1.13% (CO) and 0.47-1.08% (CH).

Tecnical Note: Analysis of non-regulated vehicular emissions by extractive FTIR spectrometry: tests on a hybrid car in Mexico City

Science.gov (United States)

Reyes, F.; Grutter, M.; Jazcilevich, A.; González-Oropeza, R.

2006-11-01

A methodology to acquire valuable information on the chemical composition and evolution of vehicular emissions is presented. The analysis of the gases is performed by passing a constant flow of a sample gas from the tail-pipe into a 10 L multi-pass cell. The absorption spectra within the cell are obtained using an FTIR spectrometer at 0.5 cm-1 resolution along a 13.1 m optical path. Additionally, the total flow from the exhaust is continuously measured from a differential pressure sensor on a textit{Pitot} tube installed at the exit of the exhaust. This configuration aims to obtain a good speciation capability by coadding spectra during 30 s and reporting the emission (in g/km) of both criteria and non-regulated pollutants, such as CO2, CO, NO, SO2, NH3, HCHO and some NMHC, during predetermined driving cycles. The advantages and disadvantages of increasing the measurement frequency, as well as the effect of other parameters such as spectral resolution, cell volume and flow rate, are discussed. To test and evaluate the proposed technique, experiments were performed on a dynamometer running FTP-75 and typical driving cycles for the Mexico City Metropolitan Area (MCMA) on a Toyota Prius hybrid vehicle. This car is an example of recent marketed automotive technology dedicated to reduced emissions, increasing the need for sensitive detection techniques. This study shows the potential of the proposed technique to measure and report in real time the emissions of a large variety of pollutants, even from a super ultra-low emission vehicle (SULEV). The emissions of HC's, NOx, CO and CO2 obtained here were compared to experiments performed in other locations with the same model vehicle. The proposed technique provides a tool for future studies comparing in detail the emissions of vehicles using alternative fuels and emission control systems.

Tecnical Note: Analysis of non-regulated vehicular emissions by extractive FTIR spectrometry: tests on a hybrid car in Mexico City

Directory of Open Access Journals (Sweden)

F. Reyes

2006-01-01

Full Text Available A methodology to acquire valuable information on the chemical composition and evolution of vehicular emissions is presented. The analysis of the gases is performed by passing a constant flow of a sample gas from the tail-pipe into a 10 L multi-pass cell. The absorption spectra within the cell are obtained using an FTIR spectrometer at 0.5 cm−1 resolution along a 13.1 m optical path. Additionally, the total flow from the exhaust is continuously measured from a differential pressure sensor on a extit{Pitot} tube installed at the exit of the exhaust. This configuration aims to obtain a good speciation capability by coadding spectra during 30 s and reporting the emission (in g/km of both criteria and non-regulated pollutants, such as CO2, CO, NO, SO2, NH3, HCHO and some NMHC, during predetermined driving cycles. The advantages and disadvantages of increasing the measurement frequency, as well as the effect of other parameters such as spectral resolution, cell volume and flow rate, are discussed. To test and evaluate the proposed technique, experiments were performed on a dynamometer running FTP-75 and typical driving cycles for the Mexico City Metropolitan Area (MCMA on a Toyota Prius hybrid vehicle. This car is an example of recent marketed automotive technology dedicated to reduced emissions, increasing the need for sensitive detection techniques. This study shows the potential of the proposed technique to measure and report in real time the emissions of a large variety of pollutants, even from a super ultra-low emission vehicle (SULEV. The emissions of HC's, NOx, CO and CO2 obtained here were compared to experiments performed in other locations with the same model vehicle. The proposed technique provides a tool for future studies comparing in detail the emissions of vehicles using alternative fuels and emission control systems.

The market for gasoline cars and diesel cars

International Nuclear Information System (INIS)

Verboven, F.

1999-01-01

In Europe the tax tariff is much lower for diesel fuel than for gasoline. This benefit is used by manufacturers to increase the price of diesel-fueled cars, which limits the possibility to control the use of diesel cars by means of a fiscal policy (tax incidence). Attention is paid to the impact of fiscal advantages for diesel cars on the purchasing behavior of the consumer and the pricing policy (price discrimination) of the car manufacturers. 1 ref

Product declaration for cars

International Nuclear Information System (INIS)

Gruetter, J.M.

2000-01-01

This reports for the Swiss Federal Office of Energy (SFOE) presents the results of a study made on the possible ways of declaring product information on cars. The basic elements of such a declaration are discussed and a recommendation for an energy label for cars is presented. The report discusses the fundamental questions posed such as how long a label should be valid, if comparisons should be made and if it is to be based on CO 2 -emissions or on fuel consumption. Also, the criteria to be used for comparisons - such as vehicle weight, size or power - are looked at and methods of classification are examined along with data fundamentals. Further, the expectations placed on the product declarations with respect to their energetic and economic impact are discussed. The design of the label and the legislature on which it is based are discussed and initial reactions of the automobile industry are noted. The report is rounded off by a discussion of the effects of the declaration in relation to other instruments that have been proposed

Simulating the impact of policy, energy prices and technological progress on the passenger car fleet in Austria-A model based analysis 2010-2050

International Nuclear Information System (INIS)

Kloess, Maximilian; Mueller, Andreas

2011-01-01

This paper investigates the effects of policy, fuel prices and technological progress on the Austrian passenger car fleet in terms of energy consumption and greenhouse gas (GHG) emissions. To analyse these effects a simulation model is used. We model the car fleet from a bottom-up perspective, with a detailed coverage of vehicle specifications and propulsion technologies. The model focuses on the technological trend toward electrified propulsion systems and their potential effects on the fleet's energy consumption and GHG emissions. To represent the impact of prices and income on the development of the fleet, we combine the fleet model with top-down demand models. We developed two scenarios for the time frame 2010-2050, using two different sets of assumptions for regulatory development and conditions of increasing fossil fuel prices and continuous technological progress in vehicle propulsion technologies. The results indicate that material cuts in energy consumption and GHG emissions can be achieved with changes to the political framework for passenger cars. Appropriate taxation of fuels and cars can stabilise demand for individual motorised transport and lead to an improvement in vehicle efficiency by fostering the adoption of efficient vehicle propulsion technologies and low carbon fuels. - Highlights: → We present a simulation model for future energy demand and greenhouse gas emissions in passenger car transport. → We develop scenarios up to 2050 assuming two different policy schemes. → Policy strongly affects energy demand and greenhouse gas emissions in passenger car transport. → Policy can slow down growth in demand for passenger car transport. → Policy can promote the diffusion of more efficient propulsion technologies and low carbon fuels.

Adaptation Model for Corporate Car Sharing in the Car Rental Industry

OpenAIRE

Matthes, Martin

2016-01-01

The focus of this thesis was on developing an adaption model for implementing a corporate car sharing service within the existing infrastructure of a car rental company. The investigated case companies were a leading Finnish car rental franchisee and an international car sharing subsidiary, largely owned by the car rental franchisor, which offers corporate car sharing solutions in major European countries. Adapting this new service in Finland will help the car rental franchisee to assert its ...

Determination of the electric field strength of filamentary DBDs by CARS-based four-wave mixing

Science.gov (United States)

Böhm, P.; Kettlitz, M.; Brandenburg, R.; Höft, H.; Czarnetzki, U.

2016-10-01

It is demonstrated that a four-wave mixing technique based on coherent anti-Stokes Raman spectroscopy (CARS) can determine the electric field strength of a pulsed-driven filamentary dielectric barrier discharge (DBD) of 1 mm gap, using hydrogen as a tracer medium in nitrogen at atmospheric pressure. The measurements are presented for a hydrogen admixture of 10%, but even 5% H2 admixture delivers sufficient infrared signals. The lasers do not affect the discharge by photoionization or by other radiation-induced processes. The absolute values of the electric field strength can be determined by the calibration of the CARS setup with high voltage amplitudes below the ignition threshold of the arrangement. This procedure also enables the determination of the applied breakdown voltage. The alteration of the electric field is observed during the internal polarity reversal and the breakdown process. One advantage of the CARS technique over emission-based methods is that it can be used independently of emission, e.g. in the pre-phase and in between two consecutive discharges, where no emission occurs at all.

Auralization of Accelerating Passenger Cars Using Spectral Modeling Synthesis

Directory of Open Access Journals (Sweden)

Reto Pieren

2015-12-01

Full Text Available While the technique of auralization has been in use for quite some time in architectural acoustics, the application to environmental noise has been discovered only recently. With road traffic noise being the dominant noise source in most countries, particular interest lies in the synthesis of realistic pass-by sounds. This article describes an auralizator for pass-bys of accelerating passenger cars. The key element is a synthesizer that simulates the acoustical emission of different vehicles, driving on different surfaces, under different operating conditions. Audio signals for the emitted tire noise, as well as the propulsion noise are generated using spectral modeling synthesis, which gives complete control of the signal characteristics. The sound of propulsion is synthesized as a function of instantaneous engine speed, engine load and emission angle, whereas the sound of tires is created in dependence of vehicle speed and emission angle. The sound propagation is simulated by applying a series of time-variant digital filters. To obtain the corresponding steering parameters of the synthesizer, controlled experiments were carried out. The tire noise parameters were determined from coast-by measurements of passenger cars with idling engines. To obtain the propulsion noise parameters, measurements at different engine speeds, engine loads and emission angles were performed using a chassis dynamometer. The article shows how, from the measured data, the synthesizer parameters are calculated using audio signal processing.

Distortionary company car taxation: deadweight losses through increased car ownership

NARCIS (Netherlands)

van Ommeren, J.N.; Gutierrez Puigarnau, E.

2013-01-01

We analyse the effects of distortionary company car taxation through increased household car consumption for the Netherlands. We use several identification strategies and demonstrate that for about 20 % of households company car possession increases car ownership. The annual welfare loss of

Emissions of nitrogen oxides and particulates of diesel vehicles

OpenAIRE

Kadijk, G.; Ligterink, N.E.; Mensch, P. van; Spreen, J.S.; Vermeulen, R.J.; Vonk, W.A.

2015-01-01

In real-world conditions, modern Euro VI heavy-duty vehicles produce an average of ten times less nitrogen oxide (NOx)emissions than previous generations of Euro IV and Euro V heavy-duty vehicles. However, Euro 6 passenger cars and light commercial vehicles present an entirely different picture since, despite a continual tightening of European emissions limits, the real-world NOx emissions of new diesel passenger cars and light commercial vehicles have remained virtually unchanged over the la...

Electric and hybrid cars - interaction with the power system; El- og hybridbiler - samspil med elsystemet

Energy Technology Data Exchange (ETDEWEB)

2010-06-15

25% of Denmark's CO{sub 2}emissions come from transport. At the same time road transport accounts for 50% of Denmark's consumption of oil. The transport sector is therefore one of the major challenges when it comes to reducing CO{sub 2}emissions. The Danish Energy Agency's report on electric vehicles' interaction with the power system concludes that electric cars can help reduce climate impacts and dependence on fossil fuels, but success would depend on whether we have an intelligent electricity grid - a smart grid. A smart grid will ensure that car batteries are charged at the times of day when demand for electricity is low but electricity is still produced from e.g. windmills. Eventually, a smart grid will also enable the power system to draw electricity from car batteries in the periods of the day when electricity demand is particularly high. A prerequisite for reaping the benefits is that electric vehicles can interplay with the power system - a requirement that will increase with more electric cars introduced. (ln)

Satisfaction and uncertainty in car-sharing decisions : an integration of hybrid choice and random regret-based models

NARCIS (Netherlands)

Kim, J.; Rasouli, S.; Timmermans, H.J.P.

2015-01-01

Increasingly, the number of private car tends to exacerbate environmental problems such as emissions, decreasing exhaustible resources, taking land for road and parking spaces, and so forth. The severity of these damaging effects is even more problematic when it is realized that private cars spend

Evolving a rule system controller for automatic driving in a car racing competition

OpenAIRE

Pérez, Diego; Sáez Achaerandio, Yago; Recio Isasi, Gustavo; Isasi Viñuela, Pedro

2008-01-01

IEEE Symposium on Computational Intelligence and Games. Perth, Australia, 15-18 December 2008. The techniques and the technologies supporting Automatic Vehicle Guidance are important issues. Automobile manufacturers view automatic driving as a very interesting product with motivating key features which allow improvement of the car safety, reduction in emission or fuel consumption or optimization of driver comfort during long journeys. Car racing is an active research field where new ...

Evaluation of NOx emissions of a retrofitted Euro 5 passenger car for the Horizon prize "Engine retrofit".

Science.gov (United States)

Giechaskiel, Barouch; Suarez-Bertoa, Ricardo; Lähde, Tero; Clairotte, Michael; Carriero, Massimo; Bonnel, Pierre; Maggiore, Maurizio

2018-06-13

The Horizon 2020 prize for the "Engine Retrofit for Clean Air" aims at reducing the pollution in cities by spurring the development of retrofit technology for diesel engines. A Euro 5 passenger car was retrofitted with an under-floor SCR (Selective Catalytic Reduction) for NO x catalyst in combination with a solid ammonia based dosing system as the NO x reductant. The vehicle was tested both on the road and on the chassis dynamometer under various test cycles and ambient temperatures. The NO x emissions were reduced by 350-1100 mg/km (60-85%) in the laboratory depending on the test cycle and engine conditions (cold or hot start), except at type approval conditions. The reduction for cold start urban cycles was < 75 mg/km (< 15%). The on road and laboratory tests were inline. In some high speed conditions significant increase of ammonia (NH 3 ) and nitrous oxide (N 2 O) were measured. No effect was seen on other pollutants (hydrocarbons, carbon monoxide and particles). The results of the present study show that retrofitting high emitting vehicles can significantly reduce vehicle NO x emissions and ultimately pollution in cities. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.

Quantifying the factors influencing people’s car type choices in Europe: Results of a stated preference survey

OpenAIRE

GOMEZ VILCHEZ JONATAN; HARRISON GILLIAN; KELLEHER LUKE; SMYTH AUSTIN; THIEL CHRISTIAN

2017-01-01

This study aims at tracking the evolution of the attitude of car drivers towards electro-mobility. The results of a new survey conducted in six European countries are shown. The purchase price continues to represent the major hurdle to widespread adoption of zero tailpipe emission cars.

An improved car-following model accounting for the preceding car's taillight

Science.gov (United States)

Zhang, Jian; Tang, Tie-Qiao; Yu, Shao-Wei

2018-02-01

During the deceleration process, the preceding car's taillight may have influences on its following car's driving behavior. In this paper, we propose an extended car-following model with consideration of the preceding car's taillight. Two typical situations are used to simulate each car's movement and study the effects of the preceding car's taillight on the driving behavior. Meanwhile, sensitivity analysis of the model parameter is in detail discussed. The numerical results show that the proposed model can improve the stability of traffic flow and the traffic safety can be enhanced without a decrease of efficiency especially when cars pass through a signalized intersection.

49 CFR 1247.1 - Annual Report of Cars Loaded and Cars Terminated.

Science.gov (United States)

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Annual Report of Cars Loaded and Cars Terminated... TRANSPORTATION BOARD, DEPARTMENT OF TRANSPORTATION (CONTINUED) ACCOUNTS, RECORDS AND REPORTS REPORT OF CARS LOADED AND CARS TERMINATED § 1247.1 Annual Report of Cars Loaded and Cars Terminated. Beginning with the...

Relationship between level of economic development and motorcycle and car ownerships and their impacts on fuel consumption and greenhouse gas emission in Thailand

Energy Technology Data Exchange (ETDEWEB)

Pongthanaisawan, Jakapong; Sorapipatana, Chumnong [The Joint Graduate School of Energy and Environment, King Mongkut' s University of Technology Thonburi, Pracha-Uthit Rd., Bangmod, Tungkru, Bangkok 10140 (Thailand); Center for Energy Technology and Environment, Ministry of Education, Bangkok (Thailand)

2010-12-15

An increase in road vehicles secondary to economic development has strongly pushed up energy demand and adversely impact the environment by the emission of greenhouse gases and pollutants. This paper aims to analyse the relationship between motorcycle and car ownerships and level of economic development in Thailand. In addition, an overall private vehicle ownership which is a sum of both types of private vehicle ownership is also studied. An understanding of these relationships due to the economic development is a key knowledge for the sustainable transport policy in the future. The results of this study revealed that at the early stage of economic development of developing countries like Thailand, the number of motorcycles predominates over private cars. Economic development strongly affects the ownership of private vehicles in two ways: (1) overall private vehicle ownerships increase as the income levels grow and (2) after personal income grows up to a certain level, people will shift from motorcycle to car ownerships for their prestige, convenience, comfort and safety. Because of continuing economic development and population growth, the expected increase in overall private vehicle ownership is projected to push up the total private vehicle stock of Thailand in the year 2050 to about twice of the present level. This will drive fuel demands in 2050 to about 2.4 times, and the greenhouse gases (GHG) emission to about 2.5 times of the current levels. Hence, policy makers in developing countries should not overlook the impacts on the consequences of increasing overall private vehicle stock in the near future. The best and most appropriate policies should be given to the development of public transport as the first priority rather than the traditional one, which gives highest priority to traffic mobility of private vehicles by road transport neglecting the effectiveness of passengers' mobility of the public transport. In addition, policies to promote high

Well-to-Wheel Analysis of Solar Hydrogen Production and Utilization for Passenger Car Transportation

Energy Technology Data Exchange (ETDEWEB)

Felder, R.; Meier, A.

2006-07-01

A well-to-wheel analysis is conducted for solar hydrogen production, transport, and usage in future passenger car transportation. Solar hydrogen production methods and selected conventional production Technologies are examined using a life cycle assessment (LCA). Utilization of hydrogen in fuel cells is compared with advanced gasoline and diesel power trains. Solar scenarios show distinctly lower greenhouse gas (GHG) emissions than fossil-based scenarios. For example, using solar hydrogen in fuel cell cars reduces life cycle GHG emissions by 75% compared to advanced fossil fuel power trains and by more than 90% if car and road infrastructure are not considered. Solar hydrogen production allows a reduction of fossil energy requirements by a factor of up to 10 compared to using conventional Technologies. Major environmental impacts are associated with the construction of the steel-intensive infrastructure for solar energy collection due to mineral and fossil resource consumption as well as discharge of pollutants related to today's steel production technology. (Author)

Effects of low concentration biodiesel blends application on modern passenger cars. Part 3: Impact on PAH, nitro-PAH, and oxy-PAH emissions

International Nuclear Information System (INIS)

Karavalakis, Georgios; Fontaras, Georgios; Ampatzoglou, Dimitrios; Kousoulidou, Marina; Stournas, Stamoulis; Samaras, Zissis; Bakeas, Evangelos

2010-01-01

This study explores the impact of five different types of methyl esters on polycyclic aromatic hydrocarbon (PAH), nitrated-PAH and oxygenated PAH emissions. The measurements were conducted on a chassis dynamometer, according to the European regulation. Each of the five different biodiesels was blended with EN590 diesel at a proportion of 10-90% v/v (10% biodiesel concentration). The vehicle was a Euro 3 compliant common-rail diesel passenger car. Emission measurements were performed over the NEDC and compared with those of the real traffic-based Artemis driving cycles. The experimental results showed that the addition of biodiesel led to some important increases in low molecular-weight PAHs (phenanthrene and anthracene) and to both increases and reductions in large PAHs which are characterised by their carcinogenic and mutagenic properties. Nitro-PAHs were found to reduce with biodiesel whereas oxy-PAH emissions presented important increases with the biodiesel blends. The impact of biodiesel source material was particularly clear on the formation of PAH compounds. It was found that most PAH emissions decreased as the average load and speed of the driving cycle increased. Cold-start conditions negatively influenced the formation of most PAH compounds. A similar trend was observed with particulate alkane emissions. - This investigation is a contribution to the understanding the impact of different biodiesels on the formation of PAHs, nitro-PAHs and oxy-PAHs over different driving conditions.

Is investing in an electric car worthwhile from a consumers' perspective?

International Nuclear Information System (INIS)

Fontaínhas, José; Cunha, Jorge; Ferreira, Paula

2016-01-01

The use of electric vehicles (EV) has long been proposed as a viable alternative to conventional cars and as a means of tackling transportation challenges related to the increasing reliance on fossil fuel and resulting greenhouse gas emissions. However, considerable barriers to its effective market uptake still persist. One of the most important ones is the cost of EV compared to other options in the same car market segment. The purpose of this paper is to assess whether the investment in an EV pays-off in different car market segments. Comparisons between internal combustion engine cars and battery EV (BEV) were undertaken, evaluating the excess cost for the consumer. The evaluation is complemented by a probabilistic risk analysis. The car market segment is found to be a relevant aspect with the results suggesting that the acquisition of BEV for the higher end car market segment can easily become a financially attractive option. On the other hand, the cost argument for acquiring a BEV on the lower/middle car market segment is still not as convincing. The analysis was undertaken assuming the current Portuguese market conditions, but the results are deemed to be pertinent for other markets and regions. - Highlights: • A comparison between ICE vehicles and BEV is established. • The excess cost for the consumer was evaluated for two cars market segments. • A probability risk analysis of the results was presented. • The car market segment is found to be a relevant aspect for the comparison.

49 CFR 172.330 - Tank cars and multi-unit tank car tanks.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Tank cars and multi-unit tank car tanks. 172.330..., TRAINING REQUIREMENTS, AND SECURITY PLANS Marking § 172.330 Tank cars and multi-unit tank car tanks. (a... material— (1) In a tank car unless the following conditions are met: (i) The tank car must be marked on...

Fuel consumption and CO{sub 2} emissions (Car Labelling); Consommations de carburant et emissions de CO{sub 2} (Car Labelling)

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-03-01

CO{sub 2} is the most important greenhouse gas produced by internal combustion engines. In the framework of the Kyoto protocol, actions have been implemented in the transportation sector for the abatement of vehicles fuel consumption and pollutant emissions. This study presents the 'honors list' established by the French agency of environment and energy mastery (Ademe) of the fuel consumption and CO{sub 2} emissions of gasoline, diesel, LPG, NGV, and hybrid electric-powered vehicles. Results are presented in tables per company and model. These data are compiled and summarized in a last part which presents the key data about the evolution of the French automotive market, the emissions and consumptions of vehicles and the technological evolution of the vehicles and its influence on the fuel consumption. (J.S.)

Vehicle emission factors of solid nanoparticles in the laboratory and on the road using Portable Emission Measurement Systems (PEMS

Directory of Open Access Journals (Sweden)

Barouch eGiechaskiel

2015-12-01

Full Text Available Emission inventories are used to quantify sources and identify trends in the emissions of air pollutants. They use vehicle-specific emission factors that are typically determined in the laboratory, through remote-sensing, vehicle chasing experiments and, more recently, on-board Portable Emission Measurement Systems (PEMS. Although PEMS is widely applied to measure gaseous pollutants, their application to Solid Particle Number (SPN emissions is new. In this paper, we discuss the current status of determining SPN emission factors both on the chassis dynamometer and on-road using PEMS-SPN. First, we determine the influence of the measurement equipment, ambient temperature, driving style and cycle characteristics, and the extra mass of the PEMS equipment on the SPN emissions. Afterward, we present the SPN emissions under type-approval conditions as well as on the road of two heavy-duty diesel vehicles equipped with Diesel Particulate Filter (DPF (one Euro VI, two light-duty diesel vehicles equipped with DPF, one light-duty vehicle equipped with a Port Fuel Injection engine (PFI, and seven Gasoline Direct Injection (GDI passenger cars (two Euro 6. We find that cold-start and strong accelerations tend to substantially increase SPN emissions. The two heavy-duty vehicles showed emissions around 2×10^13 p/km (Euro V truck and 6×10^10 p/km (Euro VI truck, respectively. One of the DPF-equipped light-duty vehicles showed emissions of 8×10^11 p/km, while the other one had one order of magnitude lower emissions. The PFI car had SPN emissions slightly higher than 1×10^12 p/km. The emissions of GDI cars spanned approximately from 8×10^11 p/km to 8×10^12 p/km. For the cars without DPF, the SPN emissions remained within a factor of two of the laboratory results. This factor was on average around 0.8 for the Euro 6 and 1.6 for the Euro 5 GDIs. The DPF equipped vehicles showed a difference of almost one order of magnitude between laboratory and on-road tests

The Norwegian support and subsidy policy of electric cars. Should it be adopted by other countries?

International Nuclear Information System (INIS)

Holtsmark, Bjart; Skonhoft, Anders

2014-01-01

Highlights: • The Norwegian policy to promote the introduction of electric vehicles (EVs) is unusually powerful. • Numerical examples show that the policy means an approximate tax relief for a EV owner about 8000 USD/year. • The same time an average EV is might imply an emission reduction of less than 1 tonne CO 2 . • The policy might cause small emission reductions at high costs. • The policy might have the unfortunate side-effect that households buy more cars and drive more. - Abstract: As a result of generous policies to increase the use of electric vehicles (EVs), the sales of EVs in Norway are rapidly increasing. This in sharp contrast to most other rich countries without such generous policies. Due to the subsidies, driving an EV implies very low costs to the owner on the margin, probably leading to more driving at the expense of public transport and cycling. Moreover, because most EVs’ driving range is low, the policy gives Norwegian households incentives to purchase a second car, again stimulating the use of private cars instead of public transport and cycling. These effects are analysed in light of possible greenhouse gas (GHG) emission benefits as well as other possible benefits of utilizing EVs versus conventional cars. We discuss whether the EV policy can be justified, as well as whether this policy should be implemented by other countries

AN INTEGRATED MODELING FRAMEWORK FOR ENVIRONMENTALLY EFFICIENT CAR OWNERSHIP AND TRIP BALANCE

Directory of Open Access Journals (Sweden)

Tao FENG

2008-01-01

Full Text Available Urban transport emissions generated by automobile trips are greatly responsible for atmospheric pollution in both developed and developing countries. To match the long-term target of sustainable development, it seems to be important to specify the feasible level of car ownership and travel demand from environmental considerations. This research intends to propose an integrated modeling framework for optimal construction of a comprehensive transportation system by taking into consideration environmental constraints. The modeling system is actually a combination of multiple essential models and illustrated by using a bi-level programming approach. In the upper level, the maximization of both total car ownership and total number of trips by private and public travel modes is set as the objective function and as the constraints, the total emission levels at all the zones are set to not exceed the relating environmental capacities. Maximizing the total trips by private and public travel modes allows policy makers to take into account trip balance to meet both the mobility levels required by travelers and the environmentally friendly transportation system goals. The lower level problem is a combined trip distribution and assignment model incorporating traveler's route choice behavior. A logit-type aggregate modal split model is established to connect the two level problems. In terms of the solution method for the integrated model, a genetic algorithm is applied. A case study is conducted using road network data and person-trip (PT data collected in Dalian city, China. The analysis results showed that the amount of environmentally efficient car ownership and number of trips by different travel modes could be obtained simultaneously when considering the zonal control of environmental capacity within the framework of the proposed integrated model. The observed car ownership in zones could be increased or decreased towards the macroscopic optimization

EVs and post 2020 CO2 targets for passenger cars

NARCIS (Netherlands)

Smokers, R.T.M.; Verbeek, M.; Zyl, S. van

2013-01-01

This paper analyses what post 2020 targets may be necessary for the European CO2 legislation for passenger cars in order to reach the overall sectoral goal of 60% reduction of transport's greenhouse gas emissions by 2050 relative to 1990, as defined in the European Commission's White Paper. The

The feasibility of long range battery electric cars in New Zealand

International Nuclear Information System (INIS)

Duke, Mike; Andrews, Deborah; Anderson, Timothy

2009-01-01

New Zealand transport accounts for over 40% of the carbon emissions with private cars accounting for 25%. In the Ministry of Economic Development's recently released 'New Zealand Energy Strategy to 2050', it proposed the wide scale deployment of electric vehicles as a means of reducing carbon emissions from transport. However, New Zealand's lack of public transport infrastructure and its subsequent reliance on private car use for longer journeys could mean that many existing battery electric vehicles (BEVs) will not have the performance to replace conventionally fuelled cars. As such, this paper discusses the potential for BEVs in New Zealand, with particular reference to the development of the University of Waikato's long-range UltraCommuter BEV. It is shown that to achieve a long range at higher speeds, BEVs should be designed specifically rather than retrofitting existing vehicles to electric. Furthermore, the electrical energy supply for a mixed fleet of 2 million BEVs is discussed and conservatively calculated, along with the number of wind turbines to achieve this. The results show that approximately 1350 MW of wind turbines would be needed to supply the mixed fleet of 2 million BEVs, or 54% of the energy produced from NZ's planned and installed wind farms.

Impact of noise barriers on the dispersal of solid pollutants from car emissions and their deposition in soil

Directory of Open Access Journals (Sweden)

Wawer Małgorzata

2017-03-01

Full Text Available Despite the existence of various methods aimed at protecting the environment from the negative influence of roads, there is a lack of adequate techniques for monitoring and reducing the spread of roadside pollution into the air and soils. The aim of this study was to assess the impact of noise barriers (sound walls on the dispersal and soil deposition of solid pollutants from car emissions, based on both quantitative and qualitative analysis. Magnetic susceptibility measurements, trace elements analyses, and platinum (Pt and rhodium (Rh content determinations were performed on soil samples collected in the vicinity of various types of noise barrier. Previous investigations have shown that most traffic emissions are deposited in the close vicinity of roads (up to 10 m, with pollution levels decreasing with increasing distance from the road edge. However, the results of the present study indicate that this distribution is disturbed in areas in which noise barriers are located. Moreover, additional soil enrichment with trace elements was observed at approx. 10-15 m behind the barriers. The spatial distribution of trace elements contents in the tested soil samples corresponded to the magnetic susceptibility values. High Fe, Zn, Mn and Pb levels were observed adjacent to noise barriers composed of sawdust concrete and steel panels.

An integral evaluation of dieselisation policies for households' cars

International Nuclear Information System (INIS)

Tovar, Miguel A.

2011-01-01

Reducing energy consumption and CO 2 emissions in the transport sector is a priority for Great Britain and other European countries as part of their agreements made in the Kyoto protocol and the Voluntary Agreement. To achieve these goals, it has been proposed to increase the market share of diesel vehicles which are more efficient than petrol ones. Based on partial approaches, previous research concluded that increasing the share of diesel vehicles will decrease CO 2 emissions (see ; ). Unlike these approaches, I use an integral approach based on discrete choice models to analyse diesel vehicle penetration in a broader context of transport in Great Britain. I provide for the first time, empirical evidence which is in line with argument that only improvements in vehicle efficiency will not be enough to achieve their goals of mitigation of energy consumption and CO 2 emissions. The model shows the technical limitations that the penetration of diesel vehicles faces and that a combination of improvements in public transportation and taxes on fuel prices is the most effective policy combination to reduce the total amount of energy consumption and CO 2 emissions among the analysed dieselisation polices. - Highlights: → Unlike other approaches, I use an integral one to analyse diesel vehicle penetration. → It is needed to make diesel cars lighter and accessible to all kind of drivers. → Having more diesel vehicles will not reduce the amount of energy and CO 2 emissions. → It provides empirical evidence of the effect of improving vehicle efficiency. → Taxing petrol cars and improving public transportation is the more efficient policy.

Positive and negative spillover effects from electric car purchase to car use

OpenAIRE

Kløckner, Christian; Nayum, Alim; Mehmetoglu, Mehmet

2013-01-01

This study reports the results of two online surveys conducted on buyers of conventional combustion engine cars compared to those of electric vehicles in Norway. The results show that electric cars are generally purchased as additional cars, do not contribute to a decrease in annual mileage if the old car is not substituted, and that electric car buyers use the car more often for their everyday mobility. Psychological determinants derived from the theory of planned behavior and the norm-activ...

Model calculations of the effects of present and future emissions of air pollutants from shipping in the Baltic Sea and the North Sea

Directory of Open Access Journals (Sweden)

J. E. Jonson

2015-01-01

Full Text Available Land-based emissions of air pollutants in Europe have steadily decreased over the past two decades, and this decrease is expected to continue. Within the same time span emissions from shipping have increased in EU ports and in the Baltic Sea and the North Sea, defined as SECAs (sulfur emission control areas, although recently sulfur emissions, and subsequently particle emissions, have decreased. The maximum allowed sulfur content in marine fuels in EU ports is now 0.1%, as required by the European Union sulfur directive. In the SECAs the maximum fuel content of sulfur is currently 1% (the global average is about 2.4%. This will be reduced to 0.1% from 2015, following the new International Maritime Organization (IMO rules. In order to assess the effects of ship emissions in and around the Baltic Sea and the North Sea, regional model calculations with the EMEP air pollution model have been made on a 1/4° longitude × 1/8° latitude resolution, using ship emissions in the Baltic Sea and the North Sea that are based on accurate ship positioning data. The effects on depositions and air pollution and the resulting number of years of life lost (YOLLs have been calculated by comparing model calculations with and without ship emissions in the two sea areas. In 2010 stricter regulations for sulfur emissions were implemented in the two sea areas, reducing the maximum sulfur content allowed in marine fuels from 1.5 to 1%. In addition ships were required to use fuels with 0.1 % sulfur in EU harbours. The calculations have been made with emissions representative of 2009 and 2011, i.e. before and after the implementation of the stricter controls on sulfur emissions from 2010. The calculations with present emissions show that per person, an additional 0.1–0.2 years of life lost is estimated in areas close to the major ship tracks with current emission levels. Comparisons of model calculations with emissions before and after the implementation of stricter

Rhodium in car exhaust tips by total automatic activation analysis

International Nuclear Information System (INIS)

Grass, F.; Westphal, G.P.; Lemmel, H.; Sterba, J.

2007-01-01

Exhaust systems of modern cars contain catalysts for the reduction of CO, NO x and hydrocarbons. These catalysts are made of ceramic materials with a large surface on which platinum metals catalyse the oxidation. The catalysts contain approximately 2 g of platinum and 0.4 g of rhodium. Recently platinum is being replaced by palladium. During driving the platinum-group elements (PGEs) are expelled from the tip in fine particles and are deposited in the environment. For a projected study of emissions from cars driven on streets and highways it is important to know which elements can be measured by short time activation analysis without any chemical procedure. (author)

Phase I Escalating-Dose Trial of CAR-T Therapy Targeting CEA+ Metastatic Colorectal Cancers.

Science.gov (United States)

Zhang, Chengcheng; Wang, Zhe; Yang, Zhi; Wang, Meiling; Li, Shiqi; Li, Yunyan; Zhang, Rui; Xiong, Zhouxing; Wei, Zhihao; Shen, Junjie; Luo, Yongli; Zhang, Qianzhen; Liu, Limei; Qin, Hong; Liu, Wei; Wu, Feng; Chen, Wei; Pan, Feng; Zhang, Xianquan; Bie, Ping; Liang, Houjie; Pecher, Gabriele; Qian, Cheng

2017-05-03

Chimeric antigen receptor T (CAR-T) cells have shown promising efficacy in treatment of hematological malignancies, but its applications in solid tumors need further exploration. In this study, we investigated CAR-T therapy targeting carcino-embryonic antigen (CEA)-positive colorectal cancer (CRC) patients with metastases to evaluate its safety and efficacy. Five escalating dose levels (DLs) (1 × 10 5 to 1 × 10 8 /CAR + /kg cells) of CAR-T were applied in 10 CRC patients. Our data showed that severe adverse events related to CAR-T therapy were not observed. Of the 10 patients, 7 patients who experienced progressive disease (PD) in previous treatments had stable disease after CAR-T therapy. Two patients remained with stable disease for more than 30 weeks, and two patients showed tumor shrinkage by positron emission tomography (PET)/computed tomography (CT) and MRI analysis, respectively. Decline of serum CEA level was apparent in most patients even in long-term observation. Furthermore, we observed persistence of CAR-T cells in peripheral blood of patients receiving high doses of CAR-T therapy. Importantly, we observed CAR-T cell proliferation especially in patients after a second CAR-T therapy. Taken together, we demonstrated that CEA CAR-T cell therapy was well tolerated in CEA + CRC patients even in high doses, and some efficacy was observed in most of the treated patients. Copyright © 2017 The American Society of Gene and Cell Therapy. Published by Elsevier Inc. All rights reserved.

Electric Car Special

Energy Technology Data Exchange (ETDEWEB)

Zoethout, T.; Belin, H.; Verwijs, H.; Nicola, S.; De Saint Jacob, Y.; Gatermann, R.

2009-09-15

In six articles, two columns and two interviews a part of this issue is dedicated to electric car developments: about winners and losers in the electric car race; a unique business model to rolling out the electric car by the electric battery company Better Place and the automobile industry Renault Nissan; interview with entrepreneur Shai Agassi of the Indian company Better Place; the development of electric cars in Germany; interview with Jean-Jacques Chanaron, an economist specialising in innovation management and a firm believer in electric cars; start of mass production of electric vehicles at the Japanese Nissan automobile industry; the constraints in Sweden in developing fuel-efficient automobiles; plans for 1 million electric or hybrid cars by 2025 in the Netherlands.

Electricity production and SO{sub 2} emissions in Poland`s power industry

Energy Technology Data Exchange (ETDEWEB)

Salay, J.

1996-09-01

The report analyzes how the Polish power industry`s electricity production and SO{sub 2} emissions have changed between 1988 and 1994. It examines to what extent the Polish government`s reform of air pollution control and its reorganization of the power industry affected power plant`s SO{sub 2} emissions in the same period. SO{sub 2} emissions from Polish power plants fell by 37% in 1988-1994. The drop in emissions was partly a result of the fall in economic activity and electricity production in the early 1990s. The main reasons for the emission reduction were the introduction of hard budget constraints, increased coal prices, and stricter enforcement of air pollution control. These reforms created strong incentives for power plants to switch to high-quality coal with lower sulfur content and higher heating value. Improved efficiency of electricity generation also contributed to the fall in SO{sub 2} emissions. 32 refs, 15 figs, 1 tab

Impact of cold temperature on Euro 6 passenger car emissions.

Science.gov (United States)

Suarez-Bertoa, Ricardo; Astorga, Covadonga

2018-03-01

Hydrocarbons, CO, NOx, NH 3 , N 2 O, CO 2 and particulate matter emissions affect air quality, global warming and human health. Transport sector is an important source of these pollutants and high pollution episodes are often experienced during the cold season. However, EU vehicle emissions regulation at cold ambient temperature only addresses hydrocarbons and CO vehicular emissions. For that reason, we have studied the impact that cold ambient temperatures have on Euro 6 diesel and spark ignition (including: gasoline, ethanol flex-fuel and hybrid vehicles) vehicle emissions using the World-harmonized Light-duty Test Cycle (WLTC) at -7 °C and 23 °C. Results indicate that when facing the WLTC at 23 °C the tested vehicles present emissions below the values set for type approval of Euro 6 vehicles (still using NEDC), with the exception of NOx emissions from diesel vehicles that were 2.3-6 times higher than Euro 6 standards. However, emissions disproportionally increased when vehicles were tested at cold ambient temperature (-7 °C). High solid particle number (SPN) emissions (>1 × 10 11 # km -1 ) were measured from gasoline direct injection (GDI) vehicles and gasoline port fuel injection vehicles. However, only diesel and GDI SPN emissions are currently regulated. Results show the need for a new, technology independent, procedure that enables the authorities to assess pollutant emissions from vehicles at cold ambient temperatures. Harmful pollutant emissions from spark ignition and diesel vehicles are strongly and negatively affected by cold ambient temperatures. Only hydrocarbon, CO emissions are currently regulated at cold temperature. Therefore, it is of great importance to revise current EU winter vehicle emissions regulation. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

From laboratory to road: Modeling the divergence between official and real-world fuel consumption and CO_2 emission values in the German passenger car market for the years 2001–2014

International Nuclear Information System (INIS)

Tietge, Uwe; Mock, Peter; Franco, Vicente; Zacharof, Nikiforos

2017-01-01

Official fuel consumption and carbon dioxide (CO_2) emission values of European passenger cars are widely recognized to be unrepresentative of real-world driving. The divergence between official and real-world values undermines national vehicle taxation schemes and EU-wide CO_2 standards for passenger cars, particularly since the divergence increases with new model generations. This study examines real-world fuel consumption data from more than 130,000 vehicles to investigate the development of the divergence. The analysis validates and refines a regression model developed by , which estimates real-world fuel consumption of cars based on readily available vehicle characteristics, namely official fuel consumption values, vehicle mass, and engine capacity. The regression model yielded coefficients of determination of 0.87 or higher, but was found to underestimate fuel consumption of newer vehicles and company cars. This study proposes to add vehicle build year as a regressor to account for the increasing divergence between official and real-world fuel consumption figures. - Highlights: • Real-world fuel consumption of new cars in Germany is 36% higher than official values. • The divergence between official and real-world fuel consumption has grown over time. • A simple regression accounts for ≥87% of the variance in real-world fuel consumption values. • Vehicle age must be included in the model to account for the growing divergence.

Dazzled by diesel? The impact on carbon dioxide emissions of the shift to diesels in Europe through 2009

International Nuclear Information System (INIS)

Schipper, Lee; Fulton, Lew

2013-01-01

This paper identifies trends in new gasoline and diesel passenger car characteristics in the European Union between 1995 and 2009. By 2009 diesels had captured over 55% of the new vehicle market. While the diesel version of a given car model may have as much as 35% lower fuel use/km and 25% lower CO 2 emissions than its gasoline equivalent, diesel buyers have chosen increasingly large and more powerful cars than the gasoline market. As a result, new diesels bought in 2009 had only 2% lower average CO 2 emissions than new gasoline cars, a smaller advantage than in 1995. A Laspeyres decomposition investigates which factors were important contributors to the observed emission reductions and which factors offset savings in other areas. More than 95% of the reduction in CO 2 emissions per km from new vehicles arose because both diesel and gasoline new vehicle emissions/km fell, and only 5% arose because of the shift from gasoline to diesel technology. Increases in vehicle mass and power for both gasoline and diesel absorbed much of the technological efficiency improvements offered by both technologies. We also observe changes in the gasoline and diesel fleets in eight EU countries and find changes in fuel and emissions intensities consistent with the changes in new vehicles reported. While diesel cars continue to be driven far farther than gasoline cars, we attribute only some of this difference to a “rebound effect”. We conclude that while diesel technology has permitted significant fuel savings, the switch from gasoline to diesel in the new vehicle market contributed little itself to the observed reductions in CO 2 emissions from new vehicles. - Highlights: ► By 2009 diesels had captured over 55% of the new car market in the EU. ► New diesels in 2009 emitted only 2% lower average CO 2 than new gasoline cars. ► Diesel cars continue to be driven farther than gasoline cars. ► Overall there has been little net CO 2 reduction from the switch to diesels in

Hybrid Engine Powered City Car: Fuzzy Controlled Approach

Science.gov (United States)

Rahman, Ataur; Mohiuddin, AKM; Hawlader, MNA; Ihsan, Sany

2017-03-01

This study describes a fuzzy controlled hybrid engine powered car. The car is powered by the lithium ion battery capacity of 1000 Wh is charged by the 50 cc hybrid engine and power regenerative mode. The engine is operated with lean mixture at 3000 rpm to charge the battery. The regenerative mode that connects with the engine generates electrical power of 500-600 W for the deceleration of car from 90 km/h to 20 km/h. The regenerated electrical power has been used to power the air-conditioning system and to meet the other electrical power. The battery power only used to propel the car. The regenerative power also found charging the battery for longer operation about 40 minutes and more. The design flexibility of this vehicle starts with whole-vehicle integration based on radical light weighting, drag reduction, and accessory efficiency. The energy efficient hybrid engine cut carbon dioxide (CO2) and nitrogen oxides (N2O) emission about 70-80% as the loads on the crankshaft such as cam-follower and its associated rotating components are replaced by electromagnetic systems, and the flywheel, alternator and starter motor are replaced by a motor generator. The vehicle was tested and found that it was able to travel 70 km/litre with the power of hybrid engine.

E-bike trials’ potential to promote sustained changes in car owners mobility habits

Science.gov (United States)

Moser, Corinne; Blumer, Yann; Lena Hille, Stefanie

2018-04-01

Modal shifts hold considerable potential to mitigate carbon emissions. Electric bikes (e-bikes) represent a promising energy- and carbon-efficient alternative to cars. However, as mobility behaviour is highly habitual, convincing people to switch from cars to e-bikes is challenging. One strategy to accomplish this is the disruption of existing habits—a key idea behind an annual e-bike promotion programme in Switzerland, in which car owners can try out an e-bike for free over a two-week period in exchange for their car keys. By means of a longitudinal survey, we measured the long-term effects of this trial on mobility-related habitual associations. After one year, participants’ habitual association with car use had weakened significantly. This finding was valid both for participants who bought an e-bike after the trial and those who did not. Our findings contrast the results of other studies who find that the effect of interventions to induce modal shifts wears off over time. We conclude that an e-bike trial has the potential to break mobility habits and motivate car owners to use more sustainable means of transport.

Car free cities: Pathway to healthy urban living.

Science.gov (United States)

Nieuwenhuijsen, Mark J; Khreis, Haneen

2016-09-01

Many cities across the world are beginning to shift their mobility solution away from the private cars and towards more environmentally friendly and citizen-focused means. Hamburg, Oslo, Helsinki, and Madrid have recently announced their plans to become (partly) private car free cities. Other cities like Paris, Milan, Chengdu, Masdar, Dublin, Brussels, Copenhagen, Bogota, and Hyderabad have measures that aim at reducing motorized traffic including implementing car free days, investing in cycling infrastructure and pedestrianization, restricting parking spaces and considerable increases in public transport provision. Such plans and measures are particularly implemented with the declared aim of reducing greenhouse gas emissions. These reductions are also likely to benefit public health. We aimed to describe the plans for private car free cities and its likely effects on public health. We reviewed the grey and scientific literature on plans for private car free cities, restricted car use, related exposures and health. An increasing number of cities are planning to become (partly) private car free. They mainly focus on the reduction of private car use in city centers. The likely effects of such policies are significant reductions in traffic-related air pollution, noise, and temperature in city centers. For example, up to a 40% reduction in NO2 levels has been reported on car free days. These reductions are likely to lead to a reduction in premature mortality and morbidity. Furthermore the reduction in the number of cars, and therefore a reduction in the need for parking places and road space, provides opportunities to increase green space and green networks in cities, which in turn can lead to many beneficial health effects. All these measures are likely to lead to higher levels of active mobility and physical activity which may improve public health the most and also provide more opportunities for people to interact with each other in public space. Furthermore, such

CAR models: next-generation CAR modifications for enhanced T-cell function

Directory of Open Access Journals (Sweden)

Daniel Abate-Daga

2016-01-01

Full Text Available T cells genetically targeted with a chimeric antigen receptor (CAR to B-cell malignancies have demonstrated tremendous clinical outcomes. With the proof in principle for CAR T cells as a therapy for B-cell malignancies being established, current and future research is being focused on adapting CAR technology to other cancers, as well as enhancing its efficacy and/or safety. The modular nature of the CAR, extracellular antigen-binding domain fused to a transmembrane domain and intracellular T-cell signaling domains, allows for optimization by replacement of the various components. These modifications are creating a whole new class of therapeutic CARs. In this review, we discuss the recent major advances in CAR design and how these modifications will impact its clinical application.

The development of CAR design for tumor CAR-T cell therapy.

Science.gov (United States)

Xu, Dandan; Jin, Guoliang; Chai, Dafei; Zhou, Xiaowan; Gu, Weiyu; Chong, Yanyun; Song, Jingyuan; Zheng, Junnian

2018-03-02

In recent years, the chimeric antigen receptor modified T cells (Chimeric antigen receptor T cells, CAR-T) immunotherapy has developed rapidly, which has been considered the most promising therapy. Efforts to enhance the efficacy of CAR-based anti-tumor therapy have been made, such as the improvement of structures of CAR-T cells, including the development of extracellular antigen recognition receptors, intracellular co-stimulatory molecules and the combination application of CARs and synthetic small molecules. In addition, effects on the function of the CAR-T cells that the space distance between the antigen binding domains and tumor targets and the length of the spacer domains have are also being investigated. Given the fast-moving nature of this field, it is necessary to make a summary of the development of CAR-T cells. In this review, we mainly focus on the present design strategies of CAR-T cells with the hope that they can provide insights to increase the anti-tumor efficacy and safety.

Transit Car Performance Comparison, State-of-the-Art Car vs. PATCO Transit Car, NYCTA R-46, MBTA Silverbirds

Science.gov (United States)

1978-02-01

The first phase of this contract authorized the design, development, and demonstration of two State-Of-The-Art Cars (SOAC). This document reports on the gathering of comparative test data on existing in-service transit cars. The three transit cars se...

ACTION AS A CRITERION OF THE CAR OPERATING EFFECTIVENES

Directory of Open Access Journals (Sweden)

Stefan POSTRZEDNIK

2016-06-01

Full Text Available Currently used criteria for determining car operating efficiency in road traffic are, among others, emission of harmful substances, consumption of engine driving fuels, technical service and reliability of operation, safety of use. The operational characteristics of the car in terms of engine driving fuel consumption data is usually recognised as so-called road specific fuel consumption. An important deficiency of this approach is the failure to take into account the influence of the time on the journey’s effectiveness and the final result of the entire project. To obtain a new solution in this range in the analysis, a quantity called "action", which at last will be treated as the criterion of the car operating effectiveness, was used. The quantity of action is the product of the performed work and its realisation time. Many phenomena and processes in nature take place according to the principle of "minimum of action"  this criterion can be applied in the analysis of the car’s operating efficiency taking place in road traffic. An approach of this issue is presented in this article, wherein the basic data for analysis were obtained in the framework of the car tests performed at the real traffic conditions.

Car Seat Safety

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español Car Seat Safety KidsHealth / For Parents / Car Seat Safety ... certified child passenger safety technician.) Guidelines for Choosing Car Seats Choose a seat with a label that ...

Methodology to estimate particulate matter emissions from certified commercial aircraft engines.

Science.gov (United States)

Wayson, Roger L; Fleming, Gregg G; Lovinelli, Ralph

2009-01-01

Today, about one-fourth of U.S. commercial service airports, including 41 of the busiest 50, are either in nonattainment or maintenance areas per the National Ambient Air Quality Standards. U.S. aviation activity is forecasted to triple by 2025, while at the same time, the U.S. Environmental Protection Agency (EPA) is evaluating stricter particulate matter (PM) standards on the basis of documented human health and welfare impacts. Stricter federal standards are expected to impede capacity and limit aviation growth if regulatory mandated emission reductions occur as for other non-aviation sources (i.e., automobiles, power plants, etc.). In addition, strong interest exists as to the role aviation emissions play in air quality and climate change issues. These reasons underpin the need to quantify and understand PM emissions from certified commercial aircraft engines, which has led to the need for a methodology to predict these emissions. Standardized sampling techniques to measure volatile and nonvolatile PM emissions from aircraft engines do not exist. As such, a first-order approximation (FOA) was derived to fill this need based on available information. FOA1.0 only allowed prediction of nonvolatile PM. FOA2.0 was a change to include volatile PM emissions on the basis of the ratio of nonvolatile to volatile emissions. Recent collaborative efforts by industry (manufacturers and airlines), research establishments, and regulators have begun to provide further insight into the estimation of the PM emissions. The resultant PM measurement datasets are being analyzed to refine sampling techniques and progress towards standardized PM measurements. These preliminary measurement datasets also support the continued refinement of the FOA methodology. FOA3.0 disaggregated the prediction techniques to allow for independent prediction of nonvolatile and volatile emissions on a more theoretical basis. The Committee for Aviation Environmental Protection of the International Civil

Car Sickness

Science.gov (United States)

... Preventable Diseases Healthy Children > Health Issues > Conditions > Head Neck & Nervous System > Car Sickness Health Issues Listen Español Text Size Email Print Share Car Sickness Page Content ...

Emission of particulates from the Dutch coal-fired power plants. Trend of the last 50 years

International Nuclear Information System (INIS)

Meij, R.; Te Winkel, B.H.

2005-01-01

Stricter boundary values in the European Union for particulates (PM 10 /PM 2,5 ) in the ambient air initiated a discussion. Within the framework of the 6th Environmental Action Programme (MAP) of the European Commission the programme Clean Air for Europe (CAFE) started in 2001. The aim of CAFE is to improve the air quality. In 2004 the final programme was published, recommending emission values not only for PM 10 , but also for PM 2,5 and to determine a so-called National Emission Ceiling (NEC). The question is how much the electric power sector contributes to the total emission of fine particulates. In this article an overview is given of the emissions in the last fifty years as well as for the present situation [nl

Dual direction blower system powered by solar energy to reduce car cabin temperature in open parking condition

Science.gov (United States)

Hamdan, N. S.; Radzi, M. F. M.; Damanhuri, A. A. M.; Mokhtar, S. N.

2017-10-01

El-nino phenomenon that strikes Malaysia with temperature recorded more than 35°C can lead to extreme temperature rise in car cabin up to 80°C. Various problems will arise due to this extreme rising of temperature such as the occupant are vulnerable to heat stroke, emission of benzene gas that can cause cancer due to reaction of high temperature with interior compartments, and damage of compartments in the car. The current solution available to reduce car cabin temperature including tinted of window and portable heat rejection device that are available in the market. As an alternative to reduce car cabin temperature, this project modifies the car’s air conditioning blower motor into dual direction powered by solar energy and identifies its influence to temperature inside the car, parked under scorching sun. By reducing the car cabin temperature up to 10°C which equal to 14% of reduction in the car cabin temperature, this simple proposed system aims to provide comfort to users due to its capability in improving the quality of air and moisture in the car cabin.

Perancangan dan Implementasi Kontroler PID untuk Pengaturan Autonomous Car-Following Car

Directory of Open Access Journals (Sweden)

Andreas Parluhutan Bonor Sinaga

2014-03-01

Full Text Available Pengiriman logistik ke daerah-daerah rawan bencana merupakan hal yang sangat sulit dilakukan, tentunya diperlukan pengetahuan mengenai kondisi medan jalan. Salah satu dampak yang utama adalah sulitnya melakukan manuver dalam pengendalian performansi  truk logistik yang pada umumnya berupa truk-truk gandeng. Untuk membantu pengemudi truk dalam berkendara pada kondisi tersebut, dirancang sebuah prototype mobil mandiri (Autonomous Car yang mampu melakukan manuver-manuver pergerakan secara sendirinya, salah satu manuver tersebut ialah Following Car.  Dalam Tugas Akhir ini perancangan sistem yang akan dilakukan dengan  memodelkan  dua buah kendaraan mobil RC (remote control yang bertindak sebagai  follower dan leader car. Pengoperasian dari  following car dilakukan dengan memodifikasi dari kendaraan RC-1, sedangkan RC-2 bertindak sebagai leader car yang dikondisikan secara manual. Dengan penerapan kontroler PID pada implementasi sistem didapatkan penurunan time settling menjadi 2,7 Detik dan peningkatan error steady state sebesar 2,44%. Pada implementasi diberikan kecepatan leader secara acak, dengan implementasi kontroler PID, kondisi jarak antara autonomous car dengan leader car masih dalam range keadaan ideal pada set point.

The ARTEMIS European driving cycles for measuring car pollutant emissions

OpenAIRE

ANDRE, M

2004-01-01

In the past 10 years, various work has been undertaken to collect data on the actual driving of European cars and to derive representative real-world driving cycles. A compilation and synthesis of this work is provided in this paper. In the frame of the European research project: ARTEMIS, this work has been considered to derive a set of reference driving cycles. The main objectives were as follows:- to derive a common set of reference real-world driving cycles to be used in the frame of the A...

Cars and fuels for tomorrow: A comparative assessment

International Nuclear Information System (INIS)

Aahman, Max; Nilsson, Lars J.; Johansson, Bengt

2001-01-01

Light duty vehicles, i.e. passenger cars and light trucks, account for approximately half of global transportation energy demand and, thus, a major share of carbon dioxide and other emissions from the transport sector. Energy consumption in the transport sector is expected to grow in the future, especially in developing countries. Cars with alternative powertrains to internal combustion engines (notably battery, hybrid and fuel-cell powertrains), in combination with potentially low carbon electricity or alternative fuels (notably hydrogen and methanol), can reduce energy demand by at least 50%, and carbon dioxide and regulated emissions much further. This article presents a comparative technical and economic assessment of promising future fuel/vehicle combinations. There are several promising technologies but no obvious winners. However, the electric drivetrain is a common denominator in the alternative powertrains and continued cost reductions are important for widespread deployment in future vehicles. Development paths from current fossil fuel based systems to future carbon-neutral supply systems appear to be flexible and a gradual phasing-in of new powertrains and carbon-neutral fluid fuels or electricity is technically possible. Technology development drivers and vehicle manufacturers are found mainly in industrialised countries, but developing countries represent a growing market and may have an increasingly important role in shaping the future. (author)

Combining hybrid cars and synthetic fuels with electricity generation and carbon capture and storage

International Nuclear Information System (INIS)

Vliet, Oscar van; Broek, Machteld van den; Turkenburg, Wim; Faaij, Andre

2011-01-01

We examined the co-evolution of the transportation, and electricity and heat generation sectors in the Netherlands until 2040 using a MARKAL bottom-up cost optimisation model. All scenario variants investigated indicate a switch away from crude oil-based diesel and petrol for transportation. Lowest overall CO 2 abatement cost is achieved by accommodating transportation first and using relatively expensive options for emissions reduction in electricity generation if needed. Biomass and carbon capture and storage (CCS) are used to full potential. Transportation CO 2 emissions are reduced by switching to ethanol or bio-based synthetic fuels combined with CCS, and series hybrid cars if needed. Depending on the availability of biomass and carbon storage capacity, electricity is produced from biomass, coal with CCS, or wind complemented with natural gas. Indirect greenhouse gas emissions rise to 34-54% of national emissions in 2040. The difference in annual investment required between the scenario variants with and without CO 2 emissions reductions of 68% by 2040 is 4-7 billion euro/year, or 0.5-1.2% of projected GDP. Investment costs are mostly determined by the cost of cars and electricity generation capacity. We observe competition for limited biomass supply and CO 2 storage capacity between the transportation and power sectors.

Heavy metal emissions for Danish road transport

Energy Technology Data Exchange (ETDEWEB)

Winther, M.; Slentoe, E.

2010-04-15

This report presents new heavy metal emission factors for cars, vans, trucks, buses, mopeds and motorcycles for each of the emission sources fuel consumption, engine oil, tyre wear, brake wear and road abrasion. The emission components covered are Arsenic (As), Cadmium (Cd), Chromium (Cr), Copper (Cu), Mercury (Hg), Nickel (Ni), Lead (Pb), Selenium (Se) and Zinc (Zn), all of them relevant for emission reporting to the UNECE CLRTAP (United Nations Economic Commission for Europe Convention on Long Range Transboundary Pollutants) convention. The report also presents a new Danish inventory for the year 2007. The following emissions in total TSP (in brackets) are calculated for the year 2007: As (8 kg), Cd (48 kg), Cr (197 kg), Cu (51 779 kg), Hg (28 kg), Ni (158 kg), Pb (6 989 kg), Se (33 kg) and Zn (28 556 kg). Per vehicle type cars are the most important source of emission for all heavy metal species, followed by vans, trucks, buses and 2-wheelers. By using the detailed emission factors and inventory calculation methods established in the present project, estimates of heavy metal emissions can be made for other years than 2007. (author)

A PEMS study of the emissions of gaseous pollutants and ultrafine particles from gasoline- and diesel-fueled vehicles

Science.gov (United States)

Huang, Cheng; Lou, Diming; Hu, Zhiyuan; Feng, Qian; Chen, Yiran; Chen, Changhong; Tan, Piqiang; Yao, Di

2013-10-01

On-road emission measurements of gasoline- and diesel-fueled vehicles were conducted by a portable emission measurement system (PEMS) in Shanghai, China. Horiba OBS 2200 and TSI EEPS 3090 were employed to detect gaseous and ultrafine particle emissions during the tests. The driving-based emission factors of gaseous pollutants and particle mass and number were obtained on various road types. The average NOx emission factors of the diesel bus, diesel car, and gasoline car were 8.86, 0.68, and 0.17 g km-1, all of which were in excess of their emission limits. The particle number emission factors were 7.06 × 1014, 6.08 × 1014, and 1.57 × 1014 km-1, generally higher than the results for similar vehicle types reported in the previous studies. The size distributions of the particles emitted from the diesel vehicles were mainly concentrated in the accumulation mode, while those emitted from the gasoline car were mainly distributed in the nucleation mode. Both gaseous and particle emission rates exhibit significant correlations with the change in vehicle speed and power demand. The lowest emission rates for each vehicle type were produced during idling. The highest emission rates for each vehicle type were generally found in high-VSP bins. The particle number emission rates of the gasoline car show the strongest growth trend with increasing VSP and speed. The particle number emission for the gasoline car increased by 3 orders of magnitude from idling to the highest VSP and driving speed conditions. High engine power caused by aggressive driving or heavy loads is the main contributor to high emissions for these vehicles in real-world situations.

Trends of NO-, NO 2-, and NH 3-emissions from gasoline-fueled Euro-3- to Euro-4-passenger cars

Science.gov (United States)

Heeb, Norbert V.; Saxer, Christian J.; Forss, Anna-Maria; Brühlmann, Stefan

Vehicular emissions of reactive nitrogen compounds (RNCs) such as nitric oxide (NO), nitrogen dioxide (NO 2), and ammonia (NH 3) have a substantial impact on urban air quality. NO and NO 2 support the photochemical formation of ozone, and NH 3 is involved in the atmospheric formation of secondary aerosols. Vehicular NO is mainly formed during combustion, whereas NO 2 and NH 3 are both secondary pollutants of the catalytic converter systems. Herein we report on tail-pipe RNC emissions of gasoline-fueled Euro-3- and Euro-4-passenger cars at transient driving from 0 to 150 km h -1. Two sets of 10 in-use vehicles with comparable engine size and mileage were studied with time-resolved chemical ionization-mass spectrometry (CI-MS). Each vehicle was tested in 7 different driving cycles including the legislative European (EDC) and the US FTP-75 driving cycles. Mean emission factors (EFs) for different traffic situations are reported and effects of cold start, velocity, acceleration, and deceleration are discussed. Furthermore, critical operating conditions supporting the de novo formation of NH 3 have been identified. In the EDC, mean NO- and NH 3-EFs of 57±26 and 16±12 mg km -1 were obtained for Euro-3-vehicles; those of the Euro-4-technology were lower by about 25% and 33% at the levels of 43±46 and 10±7 mg km -1, respectively. NO 2 emissions of the investigated three-way catalyst (TWC) vehicles accounted for exhaust. Velocity and acceleration had pronounced effects on the RNC emission characteristics. Mean velocity-dependent EFs for NO and NH 3 varied by about one order of magnitude from 10 to 74 and 15 to 161 mg km -1 for Euro-3-vehicles and from 12 to 44 and 7 to 144 mg km -1 for the Euro-4 fleet. We conclude that the investigated Euro-3- and Euro-4-vehicles are mainly operated under slightly reducing conditions, where the NH 3 emissions dominate over those of the NO. Under these conditions, both vehicle fleets on an average fulfilled the valid Euro-3 and Euro-4

Variations in amounts and potential sources of volatile organic chemicals in new cars

International Nuclear Information System (INIS)

Chien, Y.-C.

2007-01-01

This study examines inter-brand, intra-brand and intra-model variations in volatile organic chemical (VOC) levels inside new cars. The effect of temperature on interior VOC levels was examined using model automobiles with and without the air-conditioning running. Potential sources of VOC were assessed by comparing VOC levels with two interior trims (leather and fabric) and by analyzing VOC emissions from various interior components. Five brands of new car, both domestic and imported, were tested. Twelve targeted VOCs were collected on solid sorbents and analyzed using thermal desorption and GC/FID. VOCs from interior parts and adhesives were identified using solid phase micro-extraction (SPME) coupled with GC/MS. The VOC concentrations varied markedly among brands and within models, and individual VOC levels ranged from below the detection limit (a few μg per cubic meter) to thousands of μg per cubic meter. The intra-model variability (mean, 47%) in the VOC levels was approximately 50% that within each brand (mean, 95%). Although interior trim levels affected VOC levels, the effects differed among brands. Reduction of the cabin temperature reduced most VOC levels, but the impact was not statistically significant. Screening tests for VOCs from interior parts revealed that butylated hydroxytoluene (BHT), a common anti-oxidant, was the most common chemical. Long-chain aliphatic hydrocarbons, particularly C14-C17, were identified in most grease (lubricant) samples, and toluene and xylenes were ubiquitously present in adhesive samples. Process-related compounds, such as plasticizer, were also identified in interior parts. In-cabin VOC levels varied significantly among makes/models and interior trims. Concerned consumers should purchase older new cars from manufacturers since VOC levels inside car cabins normally declines over time. Improved processes or materials with lower VOC emission potential should be used to minimize in-cabin VOC sources for new cars

CAR2 - Czech Database of Car Speech

Directory of Open Access Journals (Sweden)

P. Sovka

1999-12-01

Full Text Available This paper presents new Czech language two-channel (stereo speech database recorded in car environment. The created database was designed for experiments with speech enhancement for communication purposes and for the study and the design of a robust speech recognition systems. Tools for automated phoneme labelling based on Baum-Welch re-estimation were realised. The noise analysis of the car background environment was done.

CAR2 - Czech Database of Car Speech

OpenAIRE

Pollak, P.; Vopicka, J.; Hanzl, V.; Sovka, Pavel

1999-01-01

This paper presents new Czech language two-channel (stereo) speech database recorded in car environment. The created database was designed for experiments with speech enhancement for communication purposes and for the study and the design of a robust speech recognition systems. Tools for automated phoneme labelling based on Baum-Welch re-estimation were realised. The noise analysis of the car background environment was done.

The Green City Car. A holistic approach for NVH abatement of city cars

OpenAIRE

Bein, Thilo; Mayer, Dirk; Elliott, Steve; Ferrali, Leonardo; Casella, Mauro; Saemann, Ernst-Ulrich; Kropp, Wolfgang; Nielsen, Finn Kryger; Meschke, Jens; Pisano, Emanuel

2014-01-01

Pursuing the different passive and active concepts in a holistic approach, the FP7 project Green City Car demonstrates the feasibility of applying active systems to NVH-related problems light city cars from a system point-of view. During the project, a city car equipped with a small engine has been considered equipped with the latest technology in terms of safety aspects related to pedestrian’s impact and car-to-car compatibility, which are of major importance in an urban environment. The noi...

Chemical composition and source of fine and nanoparticles from recent direct injection gasoline passenger cars: Effects of fuel and ambient temperature

Science.gov (United States)

Fushimi, Akihiro; Kondo, Yoshinori; Kobayashi, Shinji; Fujitani, Yuji; Saitoh, Katsumi; Takami, Akinori; Tanabe, Kiyoshi

2016-01-01

Particle number, mass, and chemical compositions (i.e., elemental carbon (EC), organic carbon (OC), elements, ions, and organic species) of fine particles emitted from four of the recent direct injection spark ignition (DISI) gasoline passenger cars and a port fuel injection (PFI) gasoline passenger car were measured under Japanese official transient mode (JC08 mode). Total carbon (TC = EC + OC) dominated the particulate mass (90% on average). EC dominated the TC for both hot and cold start conditions. The EC/TC ratios were 0.72 for PFI and 0.88-1.0 (average = 0.92) for DISI vehicles. A size-resolved chemical analysis of a DISI car revealed that the major organic components were the C20-C28 hydrocarbons for both the accumulation-mode particles and nanoparticles. Contribution of engine oil was estimated to be 10-30% for organics and the sum of the measured elements. The remaining major fraction likely originated from gasoline fuel. Therefore, it is suggested that soot (EC) also mainly originated from the gasoline. In experiments using four fuels at three ambient temperatures, the emission factors of particulate mass were consistently higher with regular gasoline than with premium gasoline. This result suggest that the high content of less-volatile compounds in fuel increase particulate emissions. These results suggest that focusing on reducing fuel-derived EC in the production process of new cars would effectively reduce particulate emission from DISI cars.

The sources, impact and management of car park runoff pollution: a review.

Science.gov (United States)

Revitt, D Michael; Lundy, Lian; Coulon, Frédéric; Fairley, Martin

2014-12-15

Traffic emissions contribute significantly to the build-up of diffuse pollution loads on urban surfaces with their subsequent mobilisation and direct discharge posing problems for receiving water quality. This review focuses on the impact and mitigation of solids, metals, nutrients and organic pollutants in the runoff deriving from car parks. Variabilities in the discharged pollutant levels and in the potentials for pollutant mitigation complicate an impact assessment of car park runoff. The different available stormwater best management practices and proprietary devices are reported to be capable of reductions of between 20% and almost 100% for both suspended solids and a range of metals. This review contributes to prioritising the treatment options which can achieve the appropriate pollutant reductions whilst conforming to the site requirements of a typical car park. By applying different treatment scenarios to the runoff from a hypothetical car park, it is shown that optimal performance, in terms of ecological benefits for the receiving water, can be achieved using a treatment train incorporating permeable paving and bioretention systems. The review identifies existing research gaps and emphasises the pertinent management practices as well as design issues which are relevant to the mitigation of car park pollution. Copyright © 2014 Elsevier Ltd. All rights reserved.

UV exposure in cars.

Science.gov (United States)

Moehrle, Matthias; Soballa, Martin; Korn, Manfred

2003-08-01

There is increasing knowledge about the hazards of solar and ultraviolet (UV) radiation to humans. Although people spend a significant time in cars, data on UV exposure during traveling are lacking. The aim of this study was to obtain basic information on personal UV exposure in cars. UV transmission of car glass samples, windscreen, side and back windows and sunroof, was determined. UV exposure of passengers was evaluated in seven German middle-class cars, fitted with three different types of car windows. UV doses were measured with open or closed windows/sunroof of Mercedes-Benz E 220 T, E 320, and S 500, and in an open convertible car (Mercedes-Benz CLK). Bacillus subtilis spore film dosimeters (Viospor) were attached to the front, vertex, cheeks, upper arms, forearms and thighs of 'adult' and 'child' dummies. UV wavelengths longer than >335 nm were transmitted through car windows, and UV irradiation >380 nm was transmitted through compound glass windscreens. There was some variation in the spectral transmission of side windows according to the type of glass. On the arms, UV exposure was 3-4% of ambient radiation when the car windows were shut, and 25-31% of ambient radiation when the windows were open. In the open convertible car, the relative personal doses reached 62% of ambient radiation. The car glass types examined offer substantial protection against short-wave UV radiation. Professional drivers should keep car windows closed on sunny days to reduce occupational UV exposure. In individuals with polymorphic light eruption, produced by long-wave UVA, additional protection by plastic films, clothes or sunscreens appears necessary.

Influences of HVO and FAME on the combustion and emissions of modern passenger car diesel engines; Einfluesse von HVO und FAME auf die Verbrennung und Emissionen moderner PKW-Dieselmotoren

Energy Technology Data Exchange (ETDEWEB)

Stengel, Benjamin [Rostock Univ. (Germany). Lehrstuhl fuer Kolbenmaschinen und Verbrennungsmotoren; Sadlowski, Thomas; Wichmann, Volker; Harndorf, Horst

2014-08-01

In the framework of this study engine tests were performed with FAME (fatty acid methyl ester) and HVO (hydrotreated vegetable oil) as straight fuels using a EURO-VI passenger car diesel engine. Standard diesel fuel (EN 590) was used as reference. To analyze the impacts of the biofuels on the combustion process the heat release rates were calculated from in-cylinder pressure measurements using a single-zone model. Furthermore emissions were measured and ECU data was recorded. Results from engine tests showed that both HVO and FAME positively affect the combustion by a decreased ignition delay due to its higher cetane number. Raw exhaust emissions of soot were clearly reduced with HVO while CO and THC emissions showed minor reductions. During FAME operation ECU control settings were shifted due to its lower heating value. FAME showed reductions of soot by 60 % which is caused by the fuel's oxygen content while NO{sub x} emissions where slightly increased. However, a fuel adapted ECU calibration could optimize, e.g., the injection timing and EGR to further reduce emissions. Tailpipe emissions were not affected by HVO and FAME as the exhaust aftertreatment systems worked similarly efficient for all three fuels.

The car and fuel of the future

International Nuclear Information System (INIS)

Romm, Joseph

2006-01-01

This paper is based on a review of the technical literature on alternative fuel vehicles (AFVs) and discussions with experts in vehicle technology and energy analysis. It is derived from analysis provided to the bipartisan National Commission on Energy Policy. The urgent need to reverse the business-as-usual growth path in global warming pollution in the next two decades to avoid serious if not catastrophic climate change necessitates action to make our vehicles far less polluting. In the near-term, by far the most cost-effective strategy for reducing emissions and fuel use is efficiency. The car of the near future is the hybrid gasoline-electric vehicle, because it can reduce gasoline consumption and greenhouse gas emissions 30 to 50% with no change in vehicle class and hence no loss of jobs or compromise on safety or performance. It will likely become the dominant vehicle platform by the year 2020. Ultimately, we will need to replace gasoline with a zero-carbon fuel. All AFV pathways require technology advances and strong government action to succeed. Hydrogen is the most challenging of all alternative fuels, particularly because of the enormous effort needed to change our existing gasoline infrastructure. The most promising AFV pathway is a hybrid that can be connected to the electric grid. These so-called plug-in hybrids or e-hybrids will likely travel three to four times as far on a kilowatt-hour of renewable electricity as fuel cell vehicles. Ideally these advanced hybrids would also be a flexible fuel vehicle capable of running on a blend of biofuels and gasoline. Such a car could travel 500 miles on 1 gal of gasoline (and 5 gal of cellulosic ethanol) and have under one-tenth the greenhouse gas emissions of current hybrids

Car use within the household

DEFF Research Database (Denmark)

de Borger, Bruno; Mulalic, Ismir; Rouwendal, Jan

2013-01-01

In this paper we study the demand for car kilometres in two-car households, focusing on the substitution between cars in response to fuel price changes. We use a large sample of detailed Danish data on two-car households to estimate—for each car owned by the household—own and cross-price effects...... of increases in fuel costs per kilometre. The empirical results show that failure to capture substitution between cars within the household can result in substantial misspecification biases. Ignoring substitution, we estimate fuel price elasticities of –0.81 and -0.65 for the primary and secondary cars...... efficient car, finding partial support for the underlying hypothesis. More importantly, the results of this extended model emphasize the importance of behavioural differences related to the position of the most fuel efficient car in the household, suggesting that households’ fuel efficiency choices...

Feebates promoting energy-efficient cars: Design options to address more consumers and possible counteracting effects

International Nuclear Information System (INIS)

Peters, Anja; Mueller, Michel G.; Haan, Peter de; Scholz, Roland W.

2008-01-01

An increasing number of countries have implemented or are evaluating feebate systems in order to reduce energy consumption of new vehicle registrations. We distinguish between absolute feebates based strictly on a vehicle's energy consumption and relative feebates normalizing energy consumption by a given car utility. This paper analyzes whether absolute or relative feebates encourage more consumers to change to vehicles with lower energy consumption. We combine an analysis of all car models on sale at the end of 2005 with survey data from 326 potential new car buyers. Analysis of the car fleet with regard to behavioral changes assumed as realistic shows that relative systems succeed better in offering more consumer groups cars that are eligible for incentives. Survey results suggest that consumers show some, but limited, willingness to change behavior to obtain an incentive. However, a relative system potentially allows people to switch to cars with higher relative efficiency without actually lowering absolute CO 2 emissions. We discuss this inherent dilemma of simultaneously addressing more consumers and limiting counteracting effects. In order to find the optimal trade-off, we suggest assessing different parameters operationalizing vehicle utility by means of micro-simulation with detailed car fleet and differentiated consumer segments

Tank car leaks gasoline

International Nuclear Information System (INIS)

Anon.

1997-01-01

On January 27, 1994, a Canadian National (CN) tank car loaded with gasoline began to leak from a crack in the tank shell on the end of the car near the stub sill. The tank car had been damaged from impact switching. A part of the tank car was sent for laboratory analysis which concluded that: (1) the fracture originated in two locations in welds, (2) the cracks propagated in a symmetrical manner and progressed into the tank plate, (3) the fracture surface revealed inadequate weld fusion. A stress analysis of the tank car was conducted to determine the coupling force necessary to cause the crack. It was noted that over the last decade several problems have occurred pertaining to stub sill areas of tank cars that have resulted in hazardous material spills. An advisory was sent to Transport Canada outlining many examples where tank cars containing serious defects had passed CN inspections that were specifically designed to identify such defects. 4 figs

Car allocation between household heads in car deficient households : A decision model

NARCIS (Netherlands)

Anggraini, Renni; Arentze, Theo A.; Timmermans, Harry J P

2008-01-01

This paper considers car allocation choice behaviour in car-deficient households explicitly in the context of an activity-scheduling process, focusing on work activities. A decision tree induction method is applied to derive a decision tree for the car allocation decision in automobile deficient

First results from car-to-car and car-to-infrastructure radio channel measurements at 5.2GHZ

OpenAIRE

Paier, Alexander; Kåredal, Johan; Czink, Nicolai; Hofstetter, Helmut; Dumard, Charlotte; Zemen, Thomas; Tufvesson, Fredrik; Mecklenbräuker, Christoph; Molisch, Andreas

2007-01-01

Car-to-car and car-to-infrastructure (henceforth called C2X) communications are constantly gaining importance for road-safety and other applications. In order to design efficient C2X systems, an understanding of realistic C2X propagation channels is required, but currently, only few measurements have been published. This paper presents a description of an extensive measurement campaign recently conducted in an urban scenario, a rural scenario, and on a highway. We focused on 4 ÿ 4 multiple-in...

Electric field strength determination in filamentary DBDs by CARS-based four-wave mixing

Science.gov (United States)

Boehm, Patrick; Kettlitz, Manfred; Brandenburg, Ronny; Hoeft, Hans; Czarnetzki, Uwe

2016-09-01

The electric field strength is a basic parameter of non-thermal plasmas. Therefore, a profound knowledge of the electric field distribution is crucial. In this contribution a four wave mixing technique based on Coherent Anti-Stokes Raman spectroscopy (CARS) is used to measure electric field strengths in filamentary dielectric barrier discharges (DBDs). The discharges are operated with a pulsed voltage in nitrogen at atmospheric pressure. Small amounts hydrogen (10 vol%) are admixed as tracer gas to evaluate the electric field strength in the 1 mm discharge gap. Absolute values of the electric field strength are determined by calibration of the CARS setup with high voltage amplitudes below the ignition threshold of the arrangement. Alteration of the electric field strength has been observed during the internal polarity reversal and the breakdown process. In this case the major advantage over emission based methods is that this technique can be used independently from emission, e.g. in the pre-phase and in between two consecutive, opposite discharge pulses where no emission occurs at all. This work was supported by the Deutsche Forschungsgemeinschaft, Forschergruppe FOR 1123 and Sonderforschungsbereich TRR 24 ``Fundamentals of complex plasmas''.

Impacts of a carbon Tax on the emissions of car transport in Switzerland: an assessment using an engineering-econometric model

International Nuclear Information System (INIS)

Carlevaro, F.; Bertholet, J.L.; Chaze, J.P.; Taffe, P.

1992-01-01

It is well-known that road transport is the economic sector most responsible for the growing consumption of fossil fuels in developed countries and, as a consequence, of carbon dioxide emissions largely accountable of the greenhouse effect. Recently, the Swiss Federal Council, as many other European governments, has undertaken to set up an energy policy aiming at reducing CO 2 emissions according to the so-called Toronto targets. Among the different measures that can be used to achieve this objective, special attention has been devoted to the carbon tax as an economic incentive to reduce fossil fuel consumption. Considering motor fuels, such a taxation can lead to a decrease in fuel demand through many mechanisms. Conventional econometric models of energy demand, even when they allow to distinguish short-run from long-run responses of consumption to changing economic conditions, do not consider this engineering description of energy demand. Therefore, they fail to capture the important distinction between demand and supply reaction of energy consumption to energy taxation. The authors present an econometric model built according to an engineering logic which takes into account three possible impacts of a motor fuel tax: on the stock of cars, on their average specific consumption and on their average intensity of use. 5 refs., 2 figs

Associations of individual, household and environmental characteristics with carbon dioxide emissions from motorised passenger travel.

Science.gov (United States)

Brand, Christian; Goodman, Anna; Rutter, Harry; Song, Yena; Ogilvie, David

2013-04-01

Carbon dioxide (CO 2 ) emissions from motorised travel are hypothesised to be associated with individual, household, spatial and other environmental factors. Little robust evidence exists on who contributes most (and least) to travel CO 2 and, in particular, the factors influencing commuting, business, shopping and social travel CO 2 . This paper examines whether and how demographic, socio-economic and other personal and environmental characteristics are associated with land-based passenger transport and associated CO 2 emissions. Primary data were collected from 3474 adults using a newly developed survey instrument in the iConnect study in the UK. The participants reported their past-week travel activity and vehicle characteristics from which CO 2 emissions were derived using an adapted travel emissions profiling method. Multivariable linear and logistic regression analyses were used to examine what characteristics predicted higher CO 2 emissions. CO 2 emissions from motorised travel were distributed highly unequally, with the top fifth of participants producing more than two fifth of emissions. Car travel dominated overall CO 2 emissions, making up 90% of the total. The strongest independent predictors of CO 2 emissions were owning at least one car, being in full-time employment and having a home-work distance of more than 10 km. Income, education and tenure were also strong univariable predictors of CO 2 emissions, but seemed to be further back on the causal pathway than having a car. Male gender, late-middle age, living in a rural area and having access to a bicycle also showed significant but weaker associations with emissions production. The findings may help inform the development of climate change mitigation policies for the transport sector. Targeting individuals and households with high car ownership, focussing on providing viable alternatives to commuting by car, and supporting planning and other policies that reduce commuting distances may provide an

Associations of individual, household and environmental characteristics with carbon dioxide emissions from motorised passenger travel

Science.gov (United States)

Brand, Christian; Goodman, Anna; Rutter, Harry; Song, Yena; Ogilvie, David

2013-01-01

Carbon dioxide (CO2) emissions from motorised travel are hypothesised to be associated with individual, household, spatial and other environmental factors. Little robust evidence exists on who contributes most (and least) to travel CO2 and, in particular, the factors influencing commuting, business, shopping and social travel CO2. This paper examines whether and how demographic, socio-economic and other personal and environmental characteristics are associated with land-based passenger transport and associated CO2 emissions. Primary data were collected from 3474 adults using a newly developed survey instrument in the iConnect study in the UK. The participants reported their past-week travel activity and vehicle characteristics from which CO2 emissions were derived using an adapted travel emissions profiling method. Multivariable linear and logistic regression analyses were used to examine what characteristics predicted higher CO2 emissions. CO2 emissions from motorised travel were distributed highly unequally, with the top fifth of participants producing more than two fifth of emissions. Car travel dominated overall CO2 emissions, making up 90% of the total. The strongest independent predictors of CO2 emissions were owning at least one car, being in full-time employment and having a home-work distance of more than 10 km. Income, education and tenure were also strong univariable predictors of CO2 emissions, but seemed to be further back on the causal pathway than having a car. Male gender, late-middle age, living in a rural area and having access to a bicycle also showed significant but weaker associations with emissions production. The findings may help inform the development of climate change mitigation policies for the transport sector. Targeting individuals and households with high car ownership, focussing on providing viable alternatives to commuting by car, and supporting planning and other policies that reduce commuting distances may provide an equitable and

Jet Car Track Site

Data.gov (United States)

Federal Laboratory Consortium — Located in Lakehurst, New Jersey, the Jet Car Track Site supports jet cars with J57 engines and has a maximum jet car thrust of 42,000 pounds with a maximum speed of...

ANALYSIS OF REAL-TIME VEHICLE HYDROCARBON EMISSIONS DATA

Science.gov (United States)

The report gives results of analyses using real-time dynamometer test emissions data from 13 passenger cars to examine variations in emissions during different speeds or modes of travel. The resulting data provided a way to separately identify idle, cruise, acceleration, and dece...

Advanced Combustion and Emission Control Technical Team Roadmap

Energy Technology Data Exchange (ETDEWEB)

None

2013-06-01

The Advanced Combustion and Emission Control (ACEC) Technical Team is focused on removing technical barriers to the commercialization of advanced, high-efficiency, emission-compliant internal combustion (IC) engines for light-duty vehicle powertrains (i.e., passenger car, minivan, SUV, and pickup trucks).

Danish emission inventories for road transport and other mobile sources

DEFF Research Database (Denmark)

Winther, Morten

have increased by 36 %, and CH4 emissions have decreased by 51 %. A N2O emission increase of 29 % is related to the relatively high emissions from older gasoline catalyst cars. The 1985-2006 emission decreases for PM (exhaust only), CO, NOX and NMVOC are 30, 69, 28 and 71 % respectively, due...

Background free CARS imaging by phase sensitive heterodyne CARS

NARCIS (Netherlands)

Jurna, M.; Korterik, Jeroen P.; Otto, Cornelis; Herek, Jennifer Lynn; Offerhaus, Herman L.

2008-01-01

In this article we show that heterodyne CARS, based on a controlled and stable phase-preserving chain, can be used to measure amplitude and phase information of molecular vibration modes. The technique is validated by a comparison of the imaginary part of the heterodyne CARS spectrum to the

The effects of CO2-differentiated vehicle tax systems on car choice, CO2 emissions and tax revenues

NARCIS (Netherlands)

Kok, R.

2011-01-01

This paper assesses the impacts of a CO2-differentiated tax policy designed to influence car purchasing trends towards lower CO2 emitting vehicles in the Netherlands. Since 2009, gasoline and diesel cars up to 110 and 95 gram CO2 per km are exempted from the vehicle registration tax (VRT). In

The sustainable car company - or the comeback of the electric car

Energy Technology Data Exchange (ETDEWEB)

Sticher, Georg; Rizoulis, Dimitrios [The Boston Consulting Group, Muenchen (Germany)

2008-07-01

Every day there are article published about the future of propulsion technology. Opinions are diverging: 'We'll sell nothing but hybrids by 2020' says one automotive executive; whereas for another power train executive ''Hybrids are a violation of physics'. The topic has moved beyond specialized automotive magazines and is strongly emotionalized: Hollywood stars appear driving hybrid vehicles and a documentary film charges the automotive industry as guilty for conspiring against and 'killing the electric car'. Those emotional discussions are largely driven by the announcement of many new vehicles powered by hybrid-electric power trains, fuel cells or batteries. The public is overwhelmed by announcements and can hardly tell concept vehicles from production announcements apart. One core aspect of sustainability is the reduction of CO2 emissions and the increase of vehicle efficiency. The electrification of the vehicle will have to be an integral part of every OEMs and suppliers' portfolio. But without adequate incentives of consumers to purchase the cars and of utilities and/or private investors to provide the necessary infrastructure, the emergence of the electric vehicle may be off to another false start. We do want to offer a structured, multi-stakeholder view in an attempt to de-mystify this rather complex topic. To this, we will present facts on what drives the need for change in the propulsion systems market, what are the viable technological options, what market scenario is likely for 2020 and what does this entail for the major stakeholders. (orig.)

Breaking car use habits

DEFF Research Database (Denmark)

Thøgersen, John; Møller, Berit Thorup

2008-01-01

Based on calls for innovative ways of reducing car traffic and research indicating that car driving is often the result of habitual decision-making and choice processes, this paper reports on a field experiment designed to test a tool aimed to entice drivers to skip the habitual choice of the car...... and consider using-or at least trying-public transport instead. About 1,000 car drivers participated in the experiment either as experimental subjects, receiving a free one-month travelcard, or as control subjects. As predicted, the intervention had a significant impact on drivers' use of public transport...... and it also neutralized the impact of car driving habits on mode choice. However, in the longer run (i.e., four months after the experiment) experimental subjects did not use public transport more than control subjects. Hence, it seems that although many car drivers choose travel mode habitually, their final...

Design of an intelligent car

Science.gov (United States)

Na, Yongyi

2017-03-01

The design of simple intelligent car, using AT89S52 single chip microcomputer as the car detection and control core; The metal sensor TL - Q5MC induction to iron, to detect the way to send feedback to the signal of single chip microcomputer, make SCM according to the scheduled work mode to control the car in the area according to the predetermined speed, and the operation mode of the microcontroller choose different also can control the car driving along s-shaped iron; Use A44E hall element to detect the car speeds; Adopts 1602 LCD display time of car driving, driving the car to stop, take turns to show the car driving time, distance, average speed and the speed of time. This design has simple structure and is easy to implement, but are highly intelligent, humane, to a certain extent reflects the intelligence.

Misuse of car safety seats.

Science.gov (United States)

Bull, M J; Stroup, K B; Gerhart, S

1988-01-01

Correct use of car seats for small children is essential to prevent serious injuries and death from automotive accidents. Failure to use a car seat properly can contribute to serious injury or death of a child. A case study in which misuse of a car seat occurred is reported. The infant died of hemorrhage and shock secondary to liver laceration which resulted from excessive pressure over the abdomen sustained on impact. Surveys of car seat use for small children prior to and following a child restraint law are also reported. Observers noted types of car seats and specific forms of misuse. Survey results suggest that parents are more likely to misuse car seats for infants than toddlers. Medical professionals can reinforce the importance of proper car seat use by incorporating specific car seat use questions into the patient interview and by providing educational materials.

Radon mitigation in a typical underground car park in Hong Kong

International Nuclear Information System (INIS)

Leung, J.K.C.; Tso, M.-Y.W.; Ho, C.W.; Hung, L.C.

1997-01-01

Experiments were conducted to investigate the equivalent dose to the lung (lung dose) due to radon in an underground car park with four levels. Size distribution of aerosols and activity size distribution of radon progeny loaded aerosols from 9 nm to 10 μm were measured and their relations to car movement and emission were investigated. Unattached fraction, equilibrium factor and PAEC of radon progeny were monitored and were used to predict the lung dose by adopting the ICRP Human Respiratory Tract Model. The mean annual (i.e. 2000 h) lung doses at the four levels, B1, B2, B3 and B4 during daytime were 1.5 , 2.4, 2.0 and 2.8 mSv respectively. The lung dose for each car park level at night were 2 times higher. Mitigation methods were investigated and it was found that increasing the ventilation rate only resulted in a few per cent reduction in the lung dose rate during daytime though a larger reduction in PAEC (50% at B1 and 38% at B4) was observed at night. Cleaning the fresh air filters and washing the car park floor with water also resulted in a 21% and 12% reduction in the lung dose rate respectively during daytime. (Author)

Danish emission inventories for road transport and other mobile sources

DEFF Research Database (Denmark)

Winther, Morten

for road transport increased by 30 %, and CH4 emissions have decreased by 74 %. A N2O emission increase of 29 % is related to the relatively high emissions from older gasoline catalyst cars. The 1985-2010 emission decrease for NOX, NMVOC, CO and particulates (exhaust only: Size is below PM2.5) -52, -84...

Product declaration for cars; Warendeklaration fuer Personenwagen

Energy Technology Data Exchange (ETDEWEB)

Gruetter, J.M.

2000-07-01

This reports for the Swiss Federal Office of Energy (SFOE) presents the results of a study made on the possible ways of declaring product information on cars. The basic elements of such a declaration are discussed and a recommendation for an energy label for cars is presented. The report discusses the fundamental questions posed such as how long a label should be valid, if comparisons should be made and if it is to be based on CO{sub 2}-emissions or on fuel consumption. Also, the criteria to be used for comparisons - such as vehicle weight, size or power - are looked at and methods of classification are examined along with data fundamentals. Further, the expectations placed on the product declarations with respect to their energetic and economic impact are discussed. The design of the label and the legislature on which it is based are discussed and initial reactions of the automobile industry are noted. The report is rounded off by a discussion of the effects of the declaration in relation to other instruments that have been proposed.

Urban traffic pollution reduction for sedan cars using petrol engines by hydro-oxide gas inclusion.

Science.gov (United States)

Al-Rousan, Ammar A; Alkheder, Sharaf; Musmar, Sa'ed A

2015-12-01

Petrol cars, in particular nonhybrid cars, contribute significantly to the pollution problem as compared with other types of cars. The originality of this article falls in the direction of using hydro-oxy gas to reduce pollution from petrol car engines. Experiments were performed in city areas at low real speeds, with constant engine speeds in the average of 2500 rpm and at variable velocity ratios (first speed was 10-20 km/hr, second speed was 20-35 km/hr, and third speed was 35-50 km/hr). Results indicated that through using hydro-oxy gas, a noticeable reduction in pollution was recorded. Oxygen (O2) percentage has increased by about 2.5%, and nitric oxide (NO) level has been reduced by about 500 ppm. Carbon monoxide (CO) has decreased by about 2.2%, and also CO2 has decreased by 2.1%. It's worth mentioning that for hybrid system in cars at speeds between 10 and 50 km/hr, the emission percentage change is zero. However, hybrid cars are less abundant than petrol cars. The originality of this paper falls in the direction of using hydro-oxy gas to reduce pollution from petrol car engines. Experiments were performed in city areas at low real speeds, with constant engine speeds in the average of 2500 rpm and at variable velocity ratios (first speed was 10-20 km/hr, second speed was 20-35 km/hr, and third speed was 35-50 km/h).

Car-use habits

DEFF Research Database (Denmark)

Møller, Berit Thorup; Thøgersen, John

2008-01-01

It is often claimed that many drivers use their private car rather habitually. The claim gains credibility from the fact that travelling to many everyday destinations fulfils all the prerequisites for habit formation: it is recurring, performed under stable circumstances and produces rewarding...... consequences. Since the decision is made quite automatically and only one choice alternative is considered (the habitually chosen one), behaviour guided by habit is difficult to change. The implications of car use habits for converting drivers to commuters using public transportation is analysed based...... to do so, car use habit, and the interaction between the two, confirms the theory-derived hypothesis that car use habits act as an obstacle to the transformation of intentions to commute by public transportation into action....

2000 emission inventory for the Lower Fraser Valley airshed

International Nuclear Information System (INIS)

2002-10-01

This emissions inventory is a compilation of all emissions in the Lower Fraser Valley International Airshed. Its objective is to harmonize the inventory data of Canada's Greater Vancouver Regional District (GVRD), the Fraser Valley Regional District (FVRD) and Whatcom County in the United States. It provides an idea of the current state of air emissions on both sides of the Canada-United States border. This inventory provides information regarding the types of emissions sources in the region, their location and the amount of air pollution emitted within a given time frame. It is designed to help manage air quality by identifying sectors which need to be more vigilant. The common air pollutants addressed in the inventory include total particulate matter, nitrogen oxides, sulphur oxides, volatile organic compounds, carbon monoxide, and ammonia. The greenhouse gases include carbon dioxide, methane, and nitrous oxide. The inventory distinguishes between point, area, and mobile sources. Carbon monoxide emissions are found to be dominated by cars, trucks and non-road engines. Nitrogen oxide emissions are also dominated by cars, trucks, marine vessels and non-road engines. Natural sources such as trees and vegetation contribute to volatile organic compounds, as do cars, lights trucks and solvent evaporation from industrial, commercial and consumer products. Marine vessels are the largest contributors of sulphur oxide emissions in the region. In addition, the petroleum industry emits 26 per cent of sulphur oxide emissions in the region. Significant amounts of particulate matter come from area sources such as wind erosion in the agricultural sector. Point sources for PM include bulk shipping terminals and the wood products industry. Agriculture contributes the largest amount of ammonia in the region. refs., tabs., figs

49 CFR 1037.2 - Cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 8 2010-10-01 2010-10-01 false Cars. 1037.2 Section 1037.2 Transportation Other... GENERAL RULES AND REGULATIONS BULK GRAIN AND GRAIN PRODUCTS-LOSS AND DAMAGE CLAIMS § 1037.2 Cars. A car is... railroad-leased cars. [57 FR 54334, Nov. 18, 1992] ...

Techno-economic comparison of series hybrid, plug-in hybrid, fuel cell and regular cars

NARCIS (Netherlands)

van Vliet, O.P.R.|info:eu-repo/dai/nl/288519361; Kruithof, T.; Turkenburg, W.C.|info:eu-repo/dai/nl/073416355; Faaij, A.P.C.|info:eu-repo/dai/nl/10685903X

2010-01-01

We examine the competitiveness of series hybrid compared to fuel cell, parallel hybrid, and regular cars. We use public domain data to determine efficiency, fuel consumption, total costs of ownership and greenhouse gas emissions resulting from drivetrain choices. The series hybrid drivetrain can be

PAH, BTEX, carbonyl compound, black-carbon, NO2 and ultrafine particle dynamometer bench emissions for Euro 4 and Euro 5 diesel and gasoline passenger cars

Science.gov (United States)

Louis, Cédric; Liu, Yao; Tassel, Patrick; Perret, Pascal; Chaumond, Agnès; André, Michel

2016-09-01

Although implementing Diesel particulate filters (DPF) and other novel aftertreatment technologies makes it possible to achieve significant reductions in particle mass emissions, it may induce the release of ultrafine particles and emissions of many other unregulated compounds. This paper focuses on (i) ultrafine particles, black carbon, BTEX, PAH, carbonyl compounds, and NO2 emissions from Euro 4 and Euro 5 Diesel and gasoline passenger cars, (ii) the influence of driving conditions (e.g., cold start, urban, rural and motorway conditions), and (iii) the impact of additive and catalysed DPF devices on vehicle emissions. Chassis dynamometer tests were conducted on four Euro 5 vehicles and two Euro 4 vehicles: gasoline vehicles with and without direct injection system and Diesel vehicles equipped with additive and catalysed particulate filters. The results showed that compared to hot-start cycles, cold-start urban cycles increased all pollutant emissions by a factor of two. The sole exception was NO2, which was reduced by a factor of 1.3-6. Particulate and black carbon emissions from the gasoline engines were significantly higher than those from the Diesel engines equipped with DPF. Moreover, the catalysed DPF emitted about 3-10 times more carbonyl compounds and particles than additive DPF, respectively, during urban driving cycles, while the additive DPF vehicles emitted 2 and 5 times more BTEX and carbonyl compounds during motorway driving cycles. Regarding particle number distribution, the motorway driving cycle induced the emission of particles smaller in diameter (mode at 15 nm) than the urban cold-start cycle (mode at 80-100 nm). The results showed a clear positive correlation between particle, black carbon, and BTEX emissions, and a negative correlation between particles and NO2.

Two billion cars. Pt. 1. Sustainable mobility electric- and hybrid drive; Zwei Milliarden Autos. T. 1. Nachhaltige Mobilitaet Elektro- und Hybridantrieb

Energy Technology Data Exchange (ETDEWEB)

Sperling, Daniel [California Univ., Davis (United States). Inst. of Transportation Studies; Gordon, Deborah

2010-10-15

China, India - developing countries are booming, and car manufacturers are in competition to open new markets. Within the coming two decades cars will double up to two billions involving a fast increasing of carbon dioxide emissions. To avoid environmental impacts measures have to be introduced, which is presented in this contribution by advanced drive technologies. (GL)

Viability of fuel cells for car production

Energy Technology Data Exchange (ETDEWEB)

Buchel, J.-P. [Renault, Trappes (France); Lisse, J.-P. [P.S.A., Trappes (France); Bernard, S. [Alten, Trappes (France)

2000-07-01

The two French car manufacturers PSA Peugeot Citroen and Renault both sell pure electric cars in an effort to reduce pollutants and carbon dioxide emissions. In addition, they have each studied fuel cell car prototypes in relation to the FEVER program for Renault and the HYDRO-GEN program for PSA. In 1999, the two manufacturers joined forces in a common program to evaluate the technical, economical and environmental viability of the fuel cell vehicle potential. The joint program has active contributions by Air Liquid, the French Atomic Energy Agency, De Nora Fuel Cells, Elf-Antar-France, Totalfina and Valeo. This paper highlighted many of the components of this program and the suitability of this new technology for industrial production at a cost competitive price. Certain automotive constraints have to be considered to propose vehicles which could provide good performance in varying temperature and operating conditions. Safety is also an important concern given that the vehicles are powered by hydrogen and a high voltage power source. Another challenges is the choice of the fuel and the economic cost of a new refueling infrastructure. Recycling was suggested as a means to recover expensive fuel cell system components such as precious catalysts, bipolar plates, membranes and other main specific parts of the fuel cell vehicle. This paper also discussed issues regarding the thermal management of the fuel cell power plant and air conditioning of the vehicles. figs.

Adverse effects of the automotive industry on carbon dioxide emissions

Directory of Open Access Journals (Sweden)

Mpho Bosupeng

2016-05-01

Full Text Available This study aims to determine the effects of the automotive industry on carbon dioxide emissions for the period from 1997 to 2010 for diverse economies, as well as the relationships between carbon dioxide discharges and output. The study applies cointegration and causality tests to validate these associations. The results of the Johansen cointegration test depict long-run associations between the quantity of passenger cars and carbon dioxide emissions in France, Sweden, Spain, Hungary and Japan. In addition, significant relations were observed between output and carbon dioxide discharges in Spain, Canada, India and Japan. Changes in output had substantial impact on emissions in Germany, Canada and India. The results also show that the number of passenger cars influences the magnitude of emissions in multiple economies. In conclusion, the automotive industry has to be considered in policies that aim to reduce carbon dioxide emissions.

NREL Model Car Competitions | NREL

Science.gov (United States)

work together building cars with guidance from a parent, teacher, or coach to compete in race and Solar and Lithium Ion model car races in Colorado. Building solar- and battery-powered cars requires listPDF for Junior Solar Sprint and Lithium-Ion Battery model cars. Junior Solar Sprint Solar Made Pitsco

Development in the technology of internal combustion engines for passenger cars over the next 10 to 15 years

Energy Technology Data Exchange (ETDEWEB)

Willand, J [Daimler Benz (Germany)

1996-12-01

The mainly use of fossil fuels and their limited resources and also the requirement of a 25% reduction of CO{sub 2}-emissions in Germany caused by the motor traffic, force the pressure on the car manufacturer to reduce the fuel consumption by respecting the emission limits given by the legislative institutions. The development of the worldwide vehicle population shows, that we can expect that markets like eastern Europe and developing countries will book the biggest amount of growing during the next decades. Related to this fact is also the amount of CO{sub 2}-Emissions caused by this countries. Of interest is that the emissions produced by cars will stagnate which is basically caused by the falling fuel consumption and in opposition the emissions of heavy trucks will expand over proportional. The reason is the strong expanding infrastructure in new markets and the fast growing number of heavy trucks in those countries. The target for Mercedes Benz is to reach a fuel economy until 2005 for the vehicle fleet of a maximum 6,0 liter / 100 km. Results concerning fuel economy could only be achieved on the base of progressive technologies. (EG)

Do tax incentives affect households' adoption of ‘green’ cars? A panel study of the Stockholm congestion tax

International Nuclear Information System (INIS)

Mannberg, Andrea; Jansson, Johan; Pettersson, Thomas; Brännlund, Runar; Lindgren, Urban

2014-01-01

Policymakers have made several attempts to introduce local and national policies to reduce CO 2 emissions and stimulate the consumer adoption of alternative fuel vehicles (ethanol/E85 cars). The purpose of this paper is to analyze how a local policy measure impacts the composition of the car fleet over time. More specifically, we take advantage of the natural experiment setting caused by the introduction of the Stockholm congestion tax (2006) to analyze how the tax affected purchases of ethanol cars that were exempted from the tax. To estimate effects, we employ a Difference-in-differences methodology. By using a comprehensive database of the car fleet and car owners, sociodemographic and geographic factors are analyzed, which is unique in the existing literature. Our results suggest that the congestion tax had a significant impact on ethanol car purchases although the effect fades away over time. Furthermore, there is a positive relationship between the level of education and ethanol car purchases. Previous adoption of an ethanol car is found to be the strongest predictor of ethanol car purchases. Finally, data indicate that Stockholmers substantially increased purchases of ethanol cars half a year before the introduction of the congestion tax, which we refer to as an anticipation effect. - Highlights: • Uses a database of car owners to analyze impacts of a congestion tax on car fleet. • Results show that the tax had a significant effect on ethanol car purchases. • Prior ownership of ethanol car and education correlates with ethanol car purchases

Evaluation of ecological impacts of synthetic natural gas from wood used in current heating and car systems

Energy Technology Data Exchange (ETDEWEB)

Felder, Remo; Dones, Roberto [Paul Scherrer Institut, 5232 Villigen PSI (Switzerland)

2007-06-15

A promising option to substitute fossil energy carriers by renewables is the production of synthetic natural gas (SNG) from wood, as this results in a flexible energy carrier usable via existing infrastructure in gas boilers or passenger cars. The comprehensive life cycle-based ecological impact of SNG is investigated and compared with standard fuels delivering the same service (natural gas, fuel oil, petrol/diesel, and wood chips). Life cycle impact assessment methodologies and external costs from airborne emissions provide measures of overall damage. The results indicate that the SNG system has the best ecological performance if the consumption of fossil resources is strongly weighted. Otherwise natural gas performs best, as its supply chain is energy-efficient and its use produces relatively low emissions. Wood systems are by far the best in terms of greenhouse gas emissions (GHG), where SNG emits about twice as much as the wood chips system. The main negative aspects of the SNG system are NO{sub x} and particulate emissions and the relatively low total energy conversion efficiency resulting from the additional processing to transform wood to gas. Direct wood combustion has a better ecological score when highly efficient particulate filters are installed. SNG performs better than oil derivatives with all the evaluation methods used. External costs for SNG are the lowest as long as GHG are valued high. SNG should preferably be used in cars, as the reduction of overall ecological impacts and external costs when substituting oil-based fuels is larger for current cars than for heating systems. (author)

Increase of child car seat temperature in cars parked in the outpatient parking lot.

Science.gov (United States)

Sugimura, Tetsu; Suzue, Junji; Kamada, Makoto; Ozaki, Yukiko; Tananari, Yoshifumi; Maeno, Yasuki; Ito, Shinichi; Nishino, Hiroshi; Kakimoto, Noriko; Yamakawa, Rumi

2011-12-01

A guideline for the safe use of child car seats (CS) was published by the Japan Pediatric Society in 2008. There have been few studies of the increase of temperature of a CS in parked cars. The aim of this study was to determine the change in the temperature of the CS in cars parked in full sun. The temperature of CS was measured during summer (July and August) in 2006, 2007, and 2008. The CS used in this study (n= 50) were for children (≤ 6 years old) who were taken by car to Sugimura Children's Medical Clinic. Temperatures were only measured on sunny days. Measurements were performed from 09.00 to 17.00 hours. Thermochron (Thermochron i-Button: G type, Maxim Integrated Products, CA, USA) was used to measure the temperatures. The maximum temperatures of CS were compared in time at the clinic, taking into consideration seat colors, and car colors. Of the 50 cars, three cars were excluded due to being in the shade while the temperature was measured. A total of 47 cars were used for this study. The temperature of the CS ranged from 38.0 to 65.5°C (47.8 ± 5.8°C). Eighteen CS (38.3%) reached a temperature of 50°C or above. The maximum temperature of the 13.00-15.00-hours group was significantly higher than that of the 09.00-11.00-hours group (P= 0.035). The CS temperatures in the black car group were significantly higher than those of the white car group (P= 0.013). CS may become very hot while a car is parked in sun, especially if the car and the CS are black, so the CS should be cooled before a young child is placed in it. Guardians of small children should be aware of this risk. © 2011 The Authors. Pediatrics International © 2011 Japan Pediatric Society.

Car stickers for 2012

CERN Multimedia

GS Department

2011-01-01

The 2012 car stickers are now available. Holders of blue car stickers will receive by internal mail their 2012 car stickers as of 5 December. Holders of red car stickers are kindly requested to come to the Registration Service (Building 55,1st floor) to renew their 2011 stickers. This service is open from Monday to Friday from 7.30 am to 5.30 pm non-stop. Documents related to the vehicles concerned are mandatory. Reception and Access Control Service – GS/IS/SIS General Infrastructure Services Department

Car stickers for 2011

CERN Multimedia

GS Department

2010-01-01

The 2011 car stickers are now available. Holders of blue car stickers will receive their 2011 car stickers by internal mail as of 15 December.   Holders of red car stickers are kindly requested to come to the Registration Service (Building 55,1st floor) to renew their 2011 stickers. This service is open from Monday to Friday from 7.30 am to 5.30 pm non-stop. Documents for the vehicles concerned must be presented. Reception and Access Control Service – GS/ISG/SIS General Infrastructure Services Department

Environmental effects of vintage cars; Milieueffecten van oldtimers

Energy Technology Data Exchange (ETDEWEB)

Hoen, A.; Traa, M.; Geilenkirchen, G.; Hilbers, H. [Planbureau voor de Leefomgeving PBL, Den Haag (Netherlands); Ligterink, N.; Kuiper, E. [TNO, Delft (Netherlands)

2012-08-15

A quick scan has been carried out on the emissions of vintage cars and the contribution that environmental zones for oldtimers can make to achieve European air quality standards. Also, an estimate is made of the impact of the current tax exemption for oldtimers on air quality. A brief overview is given of the current policy and recent policy changes for vintage cars, trends and developments with regard to ownership and use of oldtimers. Next, the approach to arrive at a forecast for 2015 is described, as well as the approach to assess the effect of an environmental zone for vintage cars [Dutch] Er is een quick scan uitgevoerd naar de uitstoot van oldtimers en de bijdrage die milieuzones voor oldtimers kunnen leveren voor het behalen van de Europese luchtkwaliteitsnormen. Ook is een inschatting gemaakt van het effect op de luchtkwaliteit van de huidige vrijstelling van de motorrijtuigenbelasting voor oldtimers. Deze notitie betreft een quickscan. Een kort overzicht wordt gegeven van het huidige beleid en de recente beleidswijzigingen voor oldtimers, trends en ontwikkelingen in het bezit en gebruik van oldtimers in de afgelopen jaren. Vervolgens wordt de aanpak beschreven om tot een prognose voor 2015 te komen, evenals de aanpak bij de inschatting van het effect van een milieuzone voor oldtimers. In hoofdstuk 5 volgen de resultaten.

The Socialist Car

DEFF Research Database (Denmark)

Christensen, Lars K.

2013-01-01

Review of L.H. Siegelbaum (ed.) The Socialist Car. Automobility in the Eastern Block. Cornell University Press, 2011.......Review of L.H. Siegelbaum (ed.) The Socialist Car. Automobility in the Eastern Block. Cornell University Press, 2011....

Effect of rear end spoiler angle of a sedan car

Science.gov (United States)

Mashud, Mohammad; Das, Rubel Chandra

2017-06-01

Automotive vehicle's performance, safety, maneuverability can be influenced by multi-disciplinary factors such as car engine, tires, aerodynamics, and ergonomics of design. With the recent years, inflation in the fuel prices & the demand to have reduced greenhouse emissions has played a significant role in redefining the car aerodynamics. The shape of the vehicle uses about 3% of fuel to overcome the resistance in urban driving, while it takes 11% of fuel for the highway driving. This considerable high value of fuel usage in highway driving attracts several design engineers to enhance the aerodynamics of the vehicle using minimal design changes. Besides, automotive vehicles have become so much faster experiencing uplift force which creates unexpected accidents. This brings the idea of using external devices, which could be attached to the present vehicle without changing the body. This paper is based on the design, developments and numeral calculation of the effects of external device, which will be spoiler that mounted at the rear side of the sedan car to make the present vehicles more aerodynamically attractive. The influence of rear spoiler on the generated lift, drag, and pressure distributions are investigated and reported using commercially available Autodesk Simulation CFD software tool.

Stimulated-emission pumping enabling sub-diffraction-limited spatial resolution in coherent anti-Stokes Raman scattering microscopy

NARCIS (Netherlands)

Cleff, C.; Gross, P.; Fallnich, C.; Offerhaus, Herman L.; Herek, Jennifer Lynn; Kruse, K.; Beeker, W.P.; Lee, Christopher James; Boller, Klaus J.

2013-01-01

We present a theoretical investigation of stimulated emission pumping to achieve sub-diffraction-limited spatial resolution in coherent anti-Stokes Raman scattering (CARS) microscopy. A pair of control light fields is used to prepopulate the Raman state involved in the CARS process prior to the CARS

Urban air chemistry and diesel vehicles emissions: Quantifying small and big hydrocarbons by CIMS to improve emission inventories

Science.gov (United States)

Jobson, B. T.; Derstroff, B.; Edtbauer, A.; VanderSchelden, G. S.; Williams, J.

2017-10-01

Emissions from vehicles are a major source of volatile organic compounds (VOCs) in urban environments. Photochemical oxidation of VOCs emitted from vehicle exhaust contributes to O3 and PM2.5 formation, harmful pollutants that major urban areas struggle to control. How will a shift to a diesel engine fleet impact urban air chemistry? Diesel vehicles are a growing fraction of the passenger vehicle fleet in Europe as a result of a deliberate policy to reduce energy consumption and CO2 emissions from the transportation sector (Sullivan et al., 2004). In countries such as France the diesel passenger fleet was already ∼50% of the total in 2009, up from 20% in 1995. Dunmore et al. (2015) have recently inferred that in London, HO radical loss rates to organic compounds is dominated by diesel engine emissions. In the US, increasingly more stringent vehicles emission standards and requirement for improved energy efficiency means spark ignition passenger vehicle emissions have declined significantly over the last 20 years, resulting in the urban diesel fleet traffic (freight trucks) having a growing importance as a source of vehicle pollution (McDonald et al., 2013). The recent scandal involving a major car manufacturer rigging emission controls for diesel passenger cars is a reminder that real world emissions of VOCs from diesel engines are not well understood nor thoroughly accounted for in air quality modeling.

Future vehicle composition structures and CO{sub 2} emissions based on automobile selection model for consumers

Energy Technology Data Exchange (ETDEWEB)

Chikahisa, T.; Tabe, Y.; Yamauchi, M. [Hokkaido Univ., Sapporo (Japan). Graduate School of Engineering, Energy and Environmental Systems Div.

2006-07-01

This paper examined future market growth trends of low emission vehicles for passenger cars in Japan, England and the United States. Reductions in carbon dioxide (CO{sub 2}) emissions occurring as a result of increased market uptake of low emission vehicles were also analyzed. A consumer model was then calibrated with statistical data from each of the analyzed countries. Transportation demands were simulated using a simple formula which included gross domestic product (GDP) growth rates for the analyzed countries. Results of the analysis showed that England has the highest potential for reducing CO{sub 2} emissions. However, none of the countries analyzed in the simulations met Kyoto protocol requirements for reduced automotive emissions. Market shares of low emission vehicles were similar in Japan and England, and it is anticipated that hybrid cars will reach a substantial share of the market in the next decade. Market growth in fuel cell-powered cars is expected to be slow. While consumer characteristics were similar in Japan and England, American consumers paid more attention to vehicle costs as opposed to maintenance costs. Results also indicated that total vehicle travelling mileage is increasing. Hybrid car purchases are expected to increase significantly in England and Japan, but gasoline-powered vehicles will maintain their market share in the United Sates. 2 refs., 2 tabs., 13 figs.

Substitution between Cars within the Household

DEFF Research Database (Denmark)

de Borger, Bruno; Mulalic, Ismir; Rouwendal, Jan

In this paper we study the demand for car kilometres in two-car households, focusing on the substitution between cars in response to fuel price changes. We use a large sample of detailed Danish data on two-car households to estimate—for each car owned by the household—own and cross-price effects...... of increases in fuel costs per kilometre. The empirical results show that failure to capture substitution between cars within the household can result in substantial misspecification biases. Ignoring substitution, we estimate fuel price elasticities of –0.81 and -0.65 for the primary and secondary cars...... efficient car, finding partial support for the underlying hypothesis. More importantly, the results of this extended model emphasize the importance of behavioural differences related to the position of the most fuel efficient car in the household, suggesting that households’ fuel efficiency choices...

Cars, Cycles, and Consumers.

Science.gov (United States)

Idleman, Hillis K. Ed.

The purpose of this consumer education module is to provide information and skills, and the ability to raise questions and find answers, while seeking the best automobile or motorcycle buy available for the money. The module may be used for a full or part semester course. The five sections (cars and the consumer, renting and leasing cars, cars and…

From Laboratory to Road. A 2014 update of official and real-world fuel concumption and CO2 values for passenger cars in Europe

NARCIS (Netherlands)

Mock, P.; Tietge, U.; Franco, V.; German, J.; Bandivadekar, A.; Ligterink, N.E.; Lambrecht, U.; Kuhlwein, J.; Riemersma, I.

2014-01-01

Europe’s passenger-car efficiency regulation has very effectively driven down the official average CO2 emissions and fuel consumption of new passenger cars in the EU. The 2015 target of 130 grams of CO2 per kilometer (g/km) was met two years ahead of schedule and manufacturers are making good

VOC from Vehicular Evaporation Emissions: Status and Control Strategy.

Science.gov (United States)

Liu, Huan; Man, Hanyang; Tschantz, Michael; Wu, Ye; He, Kebin; Hao, Jiming

2015-12-15

Vehicular evaporative emissions is an important source of volatile organic carbon (VOC), however, accurate estimation of emission amounts and scientific evaluation of control strategy for these emissions have been neglected outside of the United States. This study provides four kinds of basic emission factors: diurnal, hot soak, permeation, and refueling. Evaporative emissions from the Euro 4 vehicles (1.6 kg/year/car) are about four times those of U.S. vehicles (0.4 kg/year/car). Closing this emissions gap would have a larger impact than the progression from Euro 3 to Euro 6 tailpipe HC emission controls. Even in the first 24 h of parking, China's current reliance upon the European 24 h diurnal standard results in 508 g/vehicle/year emissions, higher than 32 g/vehicle/year from Tier 2 vehicles. The U.S. driving cycle matches Beijing real-world conditions much better on both typical trip length and average speed than current European driving cycles. At least two requirements should be added to the Chinese emissions standards: an onboard refueling vapor recovery to force the canister to be sized sufficiently large, and a 48-h evaporation test requirement to ensure that adequate purging occurs over a shorter drive sequence.

Air quality inside passenger cars

Directory of Open Access Journals (Sweden)

Joanna Faber

2017-02-01

Full Text Available Vehicle interior is a specific environment of relatively small volume, with variety of materials placed inside, including hard and soft plastics, adhesives, paints, lubricants and many others. As a result, particularly in case of newly produced vehicles, large amounts and numbers of volatile species, especially volatile organic compounds (VOCs, may be emitted and have influence vehicle interior air quality (VIAQ. Despite the fact that many of these compounds may not be harmful for human health, some of them may be toxic, and this is the reason for increasing concern of vehicle manufacturers and users recently. The level of contamination varies from one vehicle to another and may be influenced by atmospheric conditions, external pollution, user habits, quality of materials used and others. The main aim of this paper was to present current knowledge status on VIAQ, with indication of main air pollutants and their concentrations. Vehicle interior air quality is discussed on the basis of studies on new and used cars in different conditions and locations. Main sources of VOCs presence inside car cabin are discussed in this paper with additional information regarding materials emissions. Differences in sampling and analytical methodologies were not debated, however, since the results differs largely in the scope of both number and amount of VOCs, a need of testing methods harmonization is indicated. Presented data may be helpful for legislative requirements introduction.

Ortho-aminoazotoluene activates mouse constitutive androstane receptor (mCAR) and increases expression of mCAR target genes

International Nuclear Information System (INIS)

Smetanina, Mariya A.; Pakharukova, Mariya Y.; Kurinna, Svitlana M.; Dong, Bingning; Hernandez, Juan P.; Moore, David D.; Merkulova, Tatyana I.

2011-01-01

2'-3-dimethyl-4-aminoazobenzene (ortho-aminoazotoluene, OAT) is an azo dye and a rodent carcinogen that has been evaluated by the International Agency for Research on Cancer (IARC) as a possible (class 2B) human carcinogen. Its mechanism of action remains unclear. We examined the role of the xenobiotic receptor Constitutive Androstane Receptor (CAR, NR1I3) as a mediator of the effects of OAT. We found that OAT increases mouse CAR (mCAR) transactivation in a dose-dependent manner. This effect is specific because another closely related azo dye, 3'-methyl-4-dimethyl-aminoazobenzene (3'MeDAB), did not activate mCAR. Real-time Q-PCR analysis in wild-type C57BL/6 mice revealed that OAT induces the hepatic mRNA expression of the following CAR target genes: Cyp2b10, Cyp2c29, Cyp3a11, Ugt1a1, Mrp4, Mrp2 and c-Myc. CAR-null (Car -/- ) mice showed no increased expression of these genes following OAT treatment, demonstrating that CAR is required for their OAT dependent induction. The OAT-induced CAR-dependent increase of Cyp2b10 and c-Myc expression was confirmed by Western blotting. Immunohistochemistry analysis of wild-type and Car -/- livers showed that OAT did not acutely induce hepatocyte proliferation, but at much later time points showed an unexpected CAR-dependent proliferative response. These studies demonstrate that mCAR is an OAT xenosensor, and indicate that at least some of the biological effects of this compound are mediated by this nuclear receptor. - Highlights: → The azo dye and mouse carcinogen OAT is a very effective mCAR activator. → OAT increases mCAR transactivation in a dose-dependent manner. → OAT CAR-dependently increases the expression of a specific subset of CAR target genes. → OAT induces an unexpectedly deferred, but CAR-dependent hepatocyte proliferation.

Calculation of Selected Emissions from Transport Services in Road Public Transport

Directory of Open Access Journals (Sweden)

Konečný Vladimír

2017-01-01

Full Text Available The article deals with road public transport and its impact on the environment. According to the methodology given in EN 16258, CO2 emission value has been calculated. The input data for the calculation and the results are shown in the tables. The declaration is created according to STN CEN / TR 14310, which contains recommendations for compiling environmental reports. Finally, the comparison of the environmental impact of a bus and a passenger car, when converted to one passenger, bus has a lower CO2 emission than a passenger car in that section.

Crash protection of stock car racing drivers--application of biomechanical analysis of Indy car crash research.

Science.gov (United States)

Melvin, John W; Begeman, Paul C; Faller, Ronald K; Sicking, Dean L; McClellan, Scott B; Maynard, Edwin; Donegan, Michael W; Mallott, Annette M; Gideon, Thomas W

2006-11-01

Biomechanical analysis of Indy car crashes using on-board impact recorders (Melvin et al. 1998, Melvin et al. 2001) indicates that Indy car driver protection in high-energy crashes can be achieved in frontal, side, and rear crashes with severities in the range of 100 to 135 G peak deceleration and velocity changes in the range of 50 to 70 mph. These crashes were predominantly single-car impacts with the rigid concrete walls of oval tracks. This impressive level of protection was found to be due to the unique combination of a very supportive and tight-fitting cockpit-seating package, a six-point belt restraint system, and effective head padding with an extremely strong chassis that defines the seat and cockpit of a modern Indy car. In 2000 and 2001, a series of fatal crashes in stock car racing created great concern for improving the crash protection for drivers in those racecars. Unlike the Indy car, the typical racing stock car features a more spacious driver cockpit due to its resemblance to the shape of a passenger car. The typical racing seat used in stock cars did not have the same configuration or support characteristics of the Indy car seat, and five-point belt restraints were used. The tubular steel space frame chassis of a stock car also differs from an Indy car's composite chassis structure in both form and mechanical behavior. This paper describes the application of results of the biomechanical analysis of the Indy car crash studies to the unique requirements of stock car racing driver crash protection. Sled test and full-scale crash test data using both Hybrid III frontal crash anthropomorphic test devices (ATDs) and BioSID side crash ATDs for the purpose of evaluating countermeasures involving restraint systems, seats and head/neck restraints has been instrumental in guiding these developments. In addition, the development of deformable walls for oval tracks (the SAFER Barrier) is described as an adjunct to improved occupant restraint through control

Modelling and optimization of car-to-car compatibility - Modellierung und optimierung von pkw-pkw-kompatibilität

NARCIS (Netherlands)

Mooi, H.G.; Nastic, T.; Huibers, J.H.A.M.

1999-01-01

In this paper simple and more detailed MADYMO multibody models were used to simulate the car structure for improving the car-to-car compatibility of the whole car fleet. As a first step, survey studies were performed to develop a method for the optimization of car design with respect to frontal and

Impact of biogenic emission uncertainties on the simulated response of ozone and fine particulate matter to anthropogenic emission reductions.

Science.gov (United States)

Hogrefe, Christian; Isukapalli, Sastry S; Tang, Xiaogang; Georgopoulos, Panos G; He, Shan; Zalewsky, Eric E; Hao, Winston; Ku, Jia-Yeong; Key, Tonalee; Sistla, Gopal

2011-01-01

The role of emissions of volatile organic compounds and nitric oxide from biogenic sources is becoming increasingly important in regulatory air quality modeling as levels of anthropogenic emissions continue to decrease and stricter health-based air quality standards are being adopted. However, considerable uncertainties still exist in the current estimation methodologies for biogenic emissions. The impact of these uncertainties on ozone and fine particulate matter (PM2.5) levels for the eastern United States was studied, focusing on biogenic emissions estimates from two commonly used biogenic emission models, the Model of Emissions of Gases and Aerosols from Nature (MEGAN) and the Biogenic Emissions Inventory System (BEIS). Photochemical grid modeling simulations were performed for two scenarios: one reflecting present day conditions and the other reflecting a hypothetical future year with reductions in emissions of anthropogenic oxides of nitrogen (NOx). For ozone, the use of MEGAN emissions resulted in a higher ozone response to hypothetical anthropogenic NOx emission reductions compared with BEIS. Applying the current U.S. Environmental Protection Agency guidance on regulatory air quality modeling in conjunction with typical maximum ozone concentrations, the differences in estimated future year ozone design values (DVF) stemming from differences in biogenic emissions estimates were on the order of 4 parts per billion (ppb), corresponding to approximately 5% of the daily maximum 8-hr ozone National Ambient Air Quality Standard (NAAQS) of 75 ppb. For PM2.5, the differences were 0.1-0.25 microg/m3 in the summer total organic mass component of DVFs, corresponding to approximately 1-2% of the value of the annual PM2.5 NAAQS of 15 microg/m3. Spatial variations in the ozone and PM2.5 differences also reveal that the impacts of different biogenic emission estimates on ozone and PM2.5 levels are dependent on ambient levels of anthropogenic emissions.

Car Covers | Outdoor Covers Canada

OpenAIRE

Covers, Outdoor

2018-01-01

Protect your car from the elements with Ultimate Touch Car Cover. The multi-layer non-woven fabric is soft on the finish and offers 4 seasons all weather protection.https://outdoorcovers.ca/car-covers/

Potential and impacts of car-sharing in the Helsinki metropolitan area, Tampere and Turku; Autojen yhteiskayton potentiaali ja vaikutukset paakaupunkiseudulla, Turussa ja Tampereella

Energy Technology Data Exchange (ETDEWEB)

Voltti, V.

2010-07-01

previously without a car will improve, but passenger car kilometres and emissions will increase. Those giving up their car or giving up purchasing one are in a minority in numerical terms, but their passenger car kilometres are significantly reduced. As a net impact of various changes, carbon dioxide emissions from transport will fall by approximately one-third as a result of car-sharing. Studies conducted in Finland, Europe and North America have reached more or less the same conclusion. There are approximately 100,000 potential car sharers in the Helsinki metropolitan area, Turku and Tampere. This potential amounts to some 5% of the population. A more narrowly determined key potential is approximately 40% of the full potential, i.e. about 40,000 car sharers. Based on a European comparison, reaching the key potential is realistic with a time span of 10-20 years. The study presents a forecast of the number of car sharing users based on the current trend as well as in the target situation for 2020 and 2030. The impacts of car-sharing in forecast situations are also presented in the study (orig.)

Indicators for Danish greenhouse gas emissions from 1990 to 2007

Energy Technology Data Exchange (ETDEWEB)

Lyck, E.; Nielsen, Malene; Nielsen, Ole-Kenneth; Winther, M.; Hoffmann, L.; Thomsen, M.

2009-12-15

transport an important indicator is CO{sub 2} emissions from passenger cars over number of kilometres by passenger cars (priority indicator 3). The analysis shows that there is only a slight decoupling effect since the steady increase from 1990 to 2007 in total mileage by passenger cars of 44 % is accompanied by an increase in CO{sub 2} emissions of 37 %. This causes the indicator in 2007 to be at 95 % of the 1990 level. This trend is mainly due to an improvement of the average fuel efficiency for passenger cars dominated by a shift from gasoline driven cars to diesel driven. (LN)

Nanobody Based Dual Specific CARs

Directory of Open Access Journals (Sweden)

Stijn De Munter

2018-01-01

Full Text Available Recent clinical trials have shown that adoptive chimeric antigen receptor (CAR T cell therapy is a very potent and possibly curative option in the treatment of B cell leukemias and lymphomas. However, targeting a single antigen may not be sufficient, and relapse due to the emergence of antigen negative leukemic cells may occur. A potential strategy to counter the outgrowth of antigen escape variants is to broaden the specificity of the CAR by incorporation of multiple antigen recognition domains in tandem. As a proof of concept, we here describe a bispecific CAR in which the single chain variable fragment (scFv is replaced by a tandem of two single-antibody domains or nanobodies (nanoCAR. High membrane nanoCAR expression levels are observed in retrovirally transduced T cells. NanoCARs specific for CD20 and HER2 induce T cell activation, cytokine production and tumor lysis upon incubation with transgenic Jurkat cells expressing either antigen or both antigens simultaneously. The use of nanobody technology allows for the production of compact CARs with dual specificity and predefined affinity.

Nanobody Based Dual Specific CARs.

Science.gov (United States)

De Munter, Stijn; Ingels, Joline; Goetgeluk, Glenn; Bonte, Sarah; Pille, Melissa; Weening, Karin; Kerre, Tessa; Abken, Hinrich; Vandekerckhove, Bart

2018-01-30

Recent clinical trials have shown that adoptive chimeric antigen receptor (CAR) T cell therapy is a very potent and possibly curative option in the treatment of B cell leukemias and lymphomas. However, targeting a single antigen may not be sufficient, and relapse due to the emergence of antigen negative leukemic cells may occur. A potential strategy to counter the outgrowth of antigen escape variants is to broaden the specificity of the CAR by incorporation of multiple antigen recognition domains in tandem. As a proof of concept, we here describe a bispecific CAR in which the single chain variable fragment (scFv) is replaced by a tandem of two single-antibody domains or nanobodies (nanoCAR). High membrane nanoCAR expression levels are observed in retrovirally transduced T cells. NanoCARs specific for CD20 and HER2 induce T cell activation, cytokine production and tumor lysis upon incubation with transgenic Jurkat cells expressing either antigen or both antigens simultaneously. The use of nanobody technology allows for the production of compact CARs with dual specificity and predefined affinity.

Interaction of the phosphorylated DNA-binding domain in nuclear receptor CAR with its ligand-binding domain regulates CAR activation.

Science.gov (United States)

Shizu, Ryota; Min, Jungki; Sobhany, Mack; Pedersen, Lars C; Mutoh, Shingo; Negishi, Masahiko

2018-01-05

The nuclear protein constitutive active/androstane receptor (CAR or NR1I3) regulates several liver functions such as drug and energy metabolism and cell growth or death, which are often involved in the development of diseases such as diabetes and hepatocellular carcinoma. CAR undergoes a conversion from inactive homodimers to active heterodimers with retinoid X receptor α (RXRα), and phosphorylation of the DNA-binding domain (DBD) at Thr-38 in CAR regulates this conversion. Here, we uncovered the molecular mechanism by which this phosphorylation regulates the intramolecular interaction between CAR's DBD and ligand-binding domain (LBD), enabling the homodimer-heterodimer conversion. Phosphomimetic substitution of Thr-38 with Asp increased co-immunoprecipitation of the CAR DBD with CAR LBD in Huh-7 cells. Isothermal titration calorimetry assays also revealed that recombinant CAR DBD-T38D, but not nonphosphorylated CAR DBD, bound the CAR LBD peptide. This DBD-LBD interaction masked CAR's dimer interface, preventing CAR homodimer formation. Of note, EGF signaling weakened the interaction of CAR DBD T38D with CAR LBD, converting CAR to the homodimer form. The DBD-T38D-LBD interaction also prevented CAR from forming a heterodimer with RXRα. However, this interaction opened up a CAR surface, allowing interaction with protein phosphatase 2A. Thr-38 dephosphorylation then dissociated the DBD-LBD interaction, allowing CAR heterodimer formation with RXRα. We conclude that the intramolecular interaction of phosphorylated DBD with the LBD enables CAR to adapt a transient monomer configuration that can be converted to either the inactive homodimer or the active heterodimer.

Emission Control Cost-Effectiveness of Alternative-Fuel Vehicles

OpenAIRE

Wang, Quanlu; Sperling, Daniel; Olmstead, Janis

1993-01-01

Although various legislation and regulations have been adopted to promote the use of alternative-fuel vehicles for curbing urban air pollution problems, there is a lack of systematic comparisons of emission control cost-effectiveness among various alternative-fuel vehicle types. In this paper, life-cycle emission reductions and life-cycle costs were estimated for passenger cars fueled with methanol, ethanol, liquified petroleum gas, compressed natural gas, and electricity. Vehicle emission es...

The impact of 'Cash for Clunkers' on greenhouse gas emissions: a life cycle perspective

International Nuclear Information System (INIS)

Lenski, Shoshannah M; Keoleian, Gregory A; Bolon, Kevin M

2010-01-01

One of the goals of the US Consumer Assistance to Recycle and Save (CARS) Act of 2009, more commonly known as 'Cash for Clunkers', was to improve the US vehicle fleet fuel efficiency. Previous studies of the program's environmental impact have focused mainly on the effect of improved fuel economy, and the resulting reductions in fuel use and emissions during the vehicle use phase. We propose and apply a method for analyzing the net effect of CARS on greenhouse gas emissions from a full vehicle life cycle perspective, including the impact of premature production and retirement of vehicles. We find that CARS had a one-time effect of preventing 4.4 million metric tons of CO 2 -equivalent emissions, about 0.4% of US annual light-duty vehicle emissions. Of these, 3.7 million metric tons are avoided during the period of the expected remaining life of the inefficient 'clunkers'. 1.5 million metric tons are avoided as consumers purchase vehicles that are more efficient than their next replacement vehicle would otherwise have been. An additional 0.8 million metric tons are emitted as a result of premature manufacturing and disposal of vehicles. These results are sensitive to the remaining lifetime of the 'clunkers' and to the fuel economy of new vehicles in the absence of CARS, suggesting important considerations for policymakers deliberating on the use of accelerated vehicle retirement programs as a part of the greenhouse gas emissions policy.

The Impact of Employer Attitude to Green Commuting Plans on Reducing Car Driving: A Mixed Method Analysis

Directory of Open Access Journals (Sweden)

Chuan Ding

2014-04-01

Full Text Available Reducing car trips and promoting green commuting modes are generally considered important solutions to reduce the increase of energy consumption and transportation CO2 emissions. One potential solution for alleviating transportation CO2 emissions has been to identify a role for the employer through green commuter programs. This paper offers an approach to assess the effects of employer attitudes towards green commuting plans on commuter mode choice and the intermediary role car ownership plays in the mode choice decision process. A mixed method which extends the traditional discrete choice model by incorporating latent variables and mediating variables with a structure equation model was used to better understand the commuter mode choice behaviour. The empirical data were selected from Washington-Baltimore Regional Household Travel Survey in 2007-2008, including all the trips from home to workplace during the morning hours. The model parameters were estimated using the simultaneous estimation approach and the integrated model turns out to be superior to the traditional multinomial logit (MNL model accounting for the impact of employer attitudes towards green commuting. The direct and indirect effects of socio-demographic attributes and employer attitudes towards green commuting were estimated. Through the structural equation modelling with mediating variable, this approach confirmed the intermediary nature of car ownership in the choice process. The results found in this paper provide helpful information for transportation and planning policymakers to test the transportation and planning policies effects and encourage green commuting reducing transportation CO2 emissions.

Tradable Driving Credits : car users' responses towards an innovative pricing measure in the Netherlands and China

NARCIS (Netherlands)

Dogterom, N.J.

2017-01-01

Car traffic volumes continue to increase rapidly worldwide, leading to steadily rising levels of congestion and harmful emissions in many urbanised areas. Transport researchers have long been convinced of the power of pricing solutions to mitigate these problems. However, pricing initiatives have

External exposure dose of car mechanics during the maintenance of the cars from the risk cautionary area

International Nuclear Information System (INIS)

Kawakami, Hiroto; Yamada, Norikazu; Sasaki, Satoru; Kawasaki, Satoru

2011-12-01

At the request of the Local Nuclear Emergency Response Headquarters, JNES has estimated the effective external exposure dose of car mechanics during the maintenance of the cars from the risk cautionary area. JNES investigated the contamination of the cars from the risk cautionary area and of the average cars at Fukushima city cooperated by the Japan Automobile Dealers Association. Data of screed cars by the Local Nuclear Emergency Response Headquarters is also considered in. Effective external exposure dose of car mechanics treating the cars screened with the emergency situation screening level is estimated to be less than 1 mSv/y under the conservative conditions. This result shows that particular health concern isn't necessary for them. (author)

49 CFR 215.121 - Defective car body.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Defective car body. 215.121 Section 215.121..., DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Freight Car Components Car Bodies § 215.121 Defective car body. A railroad may not place or continue in service a car, if: (a) Any portion of...

Albedo decreasing trend. White cars proposal and new urban scenarios

Directory of Open Access Journals (Sweden)

Niccolò Casiddu

2014-05-01

Full Text Available Global warming caused the decrease of the albedo. Emission reduction is the most widely proposed response to this problem. However simple ideas such as cool roofs and cool pavements seem successful remedies to counter the threat. However in Italy another strategy appears more effective. By changing from dark to pastel bright automotive colours a considerable increase of the albedo can be hypothesized: the effect should be from 32% to 50% of the results obtained with an extensive application of the “cool roofs” strategy. Such a proposal involves the creation of new, unexpected cityscapes. The city is a place where the perception of space changes. The car, by definition is an object in motion, but still present, sometimes redundant in the urban landscape. What will be the perceived relationship with buildings, streets, squares where the cars are all white or pastel colour?

Engineering CAR-T cells.

Science.gov (United States)

Zhang, Cheng; Liu, Jun; Zhong, Jiang F; Zhang, Xi

2017-01-01

Chimeric antigen receptor redirected T cells (CAR-T cells) have achieved inspiring outcomes in patients with B cell malignancies, and are now being investigated in other hematologic malignancies and solid tumors. CAR-T cells are generated by the T cells from patients' or donors' blood. After the T cells are expanded and genetically modified, they are reinfused into the patients. However, many challenges still need to be resolved in order for this technology to gain widespread adoption. In this review, we first discuss the structure and evolution of chimeric antigen receptors. We then report on the tools used for production of CAR-T cells. Finally, we address the challenges posed by CAR-T cells.

Development of RaRaII solar car. Solar car RaRaII no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Ohashi, M [Toyota Motor Corp., Aichi (Japan)

1991-05-31

A solar car was developed to be able to travel, by utilizing solar energy, as a guiding car for the marathon race in the public road. That car is 210kg in weight, 1 in number of riding persons and 4.8m in smallest rotating radius. Its traveling performance is 44km h in highest speed, 10{degree} in hill-climbing ability and 0.6m s{sup 2} in acceleration. Those principal particulars satisfied the required condition of guiding car for the marathon race. That car was equipped with a polycrystalline silicon type solar cell, 6m{sup 2} in area to generate 870Wp power. A silver oxide-zinc battery, used as a secondary battery to secure traveling in case of rain, is of a performance to travel twice the marathon race road through. To satisfy the public road traveling in safety standard, that car was equipped with head lamps, wiper, direction winkers, rear-view mirrors, etc. As material of the body, aramid fiber and carbon fiber were adopted for securing the rigidity to cover the lightening in weight. That car, as used at an opportunity of intercollegiate marathon relay race, traveled a distance of about 30km which was its entire public road portion of course. 2 figs., 2 tabs.

Engineering an Affordable Self-Driving Car

KAUST Repository

Budisteanu, Alexandru Ionut

2018-01-01

for affordable self-driving cars and he designed a low-cost self-driving car. The car's roof has cameras and low-resolution 3D LiDAR equipment to detect traffic lanes, other cars, curbs and obstacles, such as people crossing by. To process this dizzying amount

Reducing Greenhouse Gas Emissions in Transport: All in One Basket?

Directory of Open Access Journals (Sweden)

Nicholas Rivers

2018-02-01

-Canadian Framework. Applied carefully, an LCFS combined with a mandate for automakers to sell more electric vehicles would be an appropriate policy for Canada to achieve meaningful emissions reductions at a tolerable cost, given other policy measures already committed to. Subsidies for electric vehicles, however, should be avoided as they turn out to be one of the least cost-effective policies to reduce emissions. Requiring car makers to sell more electric vehicles will lead to higher prices for standard internal-combustion vehicles as automakers are forced to spread the cost of the electric-vehicle mandate across their non-electric models. That in turn will lead to cheaper electric cars and pricier non-electric cars, making it likelier that consumers will gravitate in increasing numbers to electric cars, helping reduce emissions. Meanwhile, as the LFCS standard is raised, drivers of internal-combustion vehicles will face an even higher cost of filling up, again prompting more drivers to consider switching to electric vehicles. The combined effect — achievable at close to the cost of a carbon tax — will make it more expensive to drive a gasoline-powered car, similar to the effect of a carbon tax on drivers, but less visible and so less politically risky.

49 CFR 215.203 - Restricted cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Restricted cars. 215.203 Section 215.203..., DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Restricted Equipment § 215.203 Restricted cars. (a) This section restricts the operation of any railroad freight car that is— (1) More than 50...

CO{sub 2} emissions of newly homologated private cars in Switzerland: EU orientation; CO{sub 2}-Emissionen der PW-Neuzulassungen der Schweiz: Orientierung an der EU - Schlussbericht

Energy Technology Data Exchange (ETDEWEB)

Haan, P. de

2009-05-15

In this final report for the Swiss Federal Office of Energy (SFOE), the Institute for Environmental Decisions at the Swiss Federal Institute of Technology ETH in Zurich reports on the carbon dioxide emissions of newly homologated vehicles in Switzerland. The report examines if, how, until when and with which pricing-signals Switzerland can adopt the EU's strategy for attaining an average CO{sub 2} emission rate of 130 g/km for newly homologated vehicles. It is noted that the Swiss car market is completely integrated into the EU market. The models used are looked at and demand-side tools such as models on the basis of sanctions and certificates are considered. Further points examined include measures for attaining a further 10 g/km saving, as well as rebound effects and economic feasibility aspects. Finally, monitoring using annual data for result-checking and Swiss joint CO{sub 2} monitoring reporting are discussed.

Our Car as Power Plant

NARCIS (Netherlands)

Van Wijk, A.J.M.; Verhoef, L.

2014-01-01

Fuel cell cars can provide more efficient and cleaner transportation. However, we use our cars for transportation only 5% of the time. When parked, the fuel cell in the car can produce electricity from hydrogen, which is cleaner and more efficient than the current electricity system, generating

Driving CAR T-cells forward

Science.gov (United States)

Jackson, Hollie J.; Rafiq, Sarwish; Brentjens, Renier J.

2017-01-01

The engineered expression of chimeric antigen receptors (CARs) on the surface of T cells enables the redirection of T-cell specificity. Early clinical trials using CAR T cells for the treatment of patients with cancer showed modest results, but the impressive outcomes of several trials of CD19-targeted CAR T cells in the treatment of patients with B-cell malignancies have generated an increased enthusiasm for this approach. Important lessons have been derived from clinical trials of CD19-specific CAR T cells, and ongoing clinical trials are testing CAR designs directed at novel targets involved in haematological and solid malignancies. In this Review, we discuss these trials and present strategies that can increase the antitumour efficacy and safety of CAR T-cell therapy. Given the fast-moving nature of this field, we only discuss studies with direct translational application currently or soon-to-be tested in the clinical setting. PMID:27000958

Substitution between cars within the household

DEFF Research Database (Denmark)

De Borger, Bruno; Mulalic, Ismir; Rouwendal, Jan

The purpose of this paper is to study to what extent two-car households substitute the use of their less fuel efficient car by the use of their more fuel efficient car after an increase in fuel prices. Based on a simple theoretical framework we use a large sample of detailed Danish data on two-car...... households to estimate, for each car owned by the household, own and cross-price effects of increases in fuel costs per kilometer. The empirical results point at important substitution effects, so that models that estimate responses to fuel prices on the implicit or explicit assumption of one car per...

Bluetec. The concept for diesel engines with lowest emissions; Bluetec. Das Konzept fuer Dieselmotoren mit niedrigsten Emissionen

Energy Technology Data Exchange (ETDEWEB)

Schommers, Joachim; Reichel, Stephan [Daimler AG, Stuttgart (Germany); Zygan, Andreas; Binz, Ralf; Eckert, Dietmar; Paule, Markus; Kempka, Karl-Heinz [Daimler AG, Sindelfingen (Germany)

2008-05-15

In October 2006 when Mercedes-Benz introduced the model E 320 Bluetec, it brought the first production diesel passenger car to the market that met US Tier 2 Bin8 emission standards. Mercedes-Benz will continue its Bluetec offensive in 2008, offering the V6 diesel engine in the M, GL and R Classes in the USA, using the SCR/AdBlue technology which meets the US Tier 2 Bin5 emission standards and thereby all currently valid emission standards for diesel passenger cars worldwide. (orig.)

49 CFR 174.615 - Cleaning cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Cleaning cars. 174.615 Section 174.615... Requirements for Division 6.1 (Poisonous) Materials § 174.615 Cleaning cars. (a) [Reserved] (b) After Division 6.1 (poisonous) materials are unloaded from a rail car, that car must be thoroughly cleaned unless...

Modeling carbon emissions from urban traffic system using mobile monitoring.

Science.gov (United States)

Sun, Daniel Jian; Zhang, Ying; Xue, Rui; Zhang, Yi

2017-12-01

Comprehensive analyses of urban traffic carbon emissions are critical in achieving low-carbon transportation. This paper started from the architecture design of a carbon emission mobile monitoring system using multiple sets of equipment and collected the corresponding data about traffic flow, meteorological conditions, vehicular carbon emissions and driving characteristics on typical roads in Shanghai and Wuxi, Jiangsu province. Based on these data, the emission model MOVES was calibrated and used with various sensitivity and correlation evaluation indices to analyze the traffic carbon emissions at microscopic, mesoscopic and macroscopic levels, respectively. The major factors that influence urban traffic carbon emissions were investigated, so that emission factors of CO, CO 2 and HC were calculated by taking representative passenger cars as a case study. As a result, the urban traffic carbon emissions were assessed quantitatively, and the total amounts of CO, CO 2 and HC emission from passenger cars in Shanghai were estimated as 76.95kt, 8271.91kt, and 2.13kt, respectively. Arterial roads were found as the primary line source, accounting for 50.49% carbon emissions. In additional to the overall major factors identified, the mobile monitoring system and carbon emission quantification method proposed in this study are of rather guiding significance for the further urban low-carbon transportation development. Copyright © 2017 Elsevier B.V. All rights reserved.

Environmental assessment of speeding up use of particle filters on passenger cars and vans. Air quality and population exposure for PM{sub 2.5}; Miljoevurdering af fremskyndelse af partikelfiltre pae person- og varebiler. Luftkvalitet og befolkningseksponering for PM{sub 2.5}

Energy Technology Data Exchange (ETDEWEB)

Solvang Jensen, S.; Ketzel, M. [DMU, Afd. for Atmosfaerisk Miljoe (Denmark)

2006-11-15

New stringent European Union emission standards for particles are expected to be implemented around 2010 for diesel-powered passenger cars and vans. Provided that such standards are agreed upon diesel-powered passenger cars and vans are expected to be equipped with particle filters that effectively will remove particle emissions. Against this background, the Danish Environmental Assessment Institute wanted to carry out a cost-benefit analysis of a scenario where the emission standards came into force in 2007 instead of 2010. The objective of the project is to assess the effects on particle emissions and air quality of PM{sub 2.5} (particles less than 2.5 micrometer) of moving forward the emission standards for passenger cars and vans. An assessment of a scenario is carried out that assumes that all new diesel-powered passenger cars and vans entering the vehicle fleet during January 1st, 2007 and December 31st, 2009 will be equipped with particle filters. The National Environmental Research Institute has carried out this assessment. (au)

Proton - Malaysia's national car project

DEFF Research Database (Denmark)

Fleming, Daniel; Søborg, Henrik

2017-01-01

The rise and development of the Malaysian national car project. How this project has become an esential part of the industrial development in Malaysia and how it has underpinned a growing middle class consumption culture with house and car as it pivotal goods.......The rise and development of the Malaysian national car project. How this project has become an esential part of the industrial development in Malaysia and how it has underpinned a growing middle class consumption culture with house and car as it pivotal goods....

PM₂.₅ emissions from light-duty gasoline vehicles in Beijing, China.

Science.gov (United States)

Shen, Xianbao; Yao, Zhiliang; Huo, Hong; He, Kebin; Zhang, Yingzhi; Liu, Huan; Ye, Yu

2014-07-15

As stricter standards for diesel vehicles are implemented in China, and the use of diesel trucks is forbidden in urban areas, determining the contribution of light-duty gasoline vehicles (LDGVs) to on-road PM2.5 emissions in cities is important. Additionally, in terms of particle number and size, particulates emitted from LDGVs have a greater health impact than particulates emitted from diesel vehicles. In this work, we measured PM2.5 emissions from 20 LDGVs in Beijing, using an improved combined on-board emission measurement system. We compared these measurements with those reported in previous studies, and estimated the contribution of LDGVs to on-road PM2.5 emissions in Beijing. The results show that the PM2.5 emission factors for LDGVs, complying with European Emission Standards Euro-0 through Euro-4 were: 117.4 ± 142, 24.1 ± 20.4, 4.85 ± 7.86, 0.99 ± 1.32, 0.17 ± 0.15 mg/km, respectively. Our results show a significant decline in emissions with improving vehicle technology. However, this trend is not reflected in recent emission inventory studies. The daytime contributions of LDGVs to PM2.5 emissions on highways, arterials, residential roads, and within urban areas of Beijing were 44%, 62%, 57%, and 57%, respectively. The contribution of LDGVs to PM2.5 emissions varied both for different road types and for different times. Copyright © 2014 Elsevier B.V. All rights reserved.

Are weeds hitchhiking a ride on your car? A systematic review of seed dispersal on cars.

Directory of Open Access Journals (Sweden)

Michael Ansong

Full Text Available When traveling in cars, we can unintentionally carry and disperse weed seed; but which species, and where are they a problem? To answer these questions, we systematically searched the scientific literature to identify all original research studies that assess seed transported by cars and listed the species with seed on/in cars. From the 13 studies that fit these criteria, we found 626 species from 75 families that have seed that can be dispersed by cars. Of these, 599 are listed as weeds in some part of the world, with 439 listed as invasive or naturalized alien species in one or more European countries, 248 are invasive/noxious weeds in North America, 370 are naturalized alien species in Australia, 167 are alien species in India, 77 are invasive species in China and 23 are declared weeds/invaders in South Africa. One hundred and one are classified as internationally important environmental weeds. Although most (487 were only recorded once, some species such as Chenopodium album, Poa pratensis and Trifolium repens were common among studies. Perennial graminoids seem to be favoured over annual graminoids while annual forbs are favoured over perennial forbs. Species characteristics including seed size and morphology and where the plants grew affected the probability that their seed was transported by cars. Seeds can be found in many different places on cars including under the chassis, front and rear bumpers, wheel wells and rims, front and back mudguards, wheel arches, tyres and on interior floor mats. With increasing numbers of cars and expanding road networks in many regions, these results highlight the importance of cars as a dispersal mechanism, and how it may favour invasions by some species over others. Strategies to reduce the risk of seed dispersal by cars include reducing seed on cars by mowing road verges and cleaning cars.

Concept for lowest emissions of a hydrogen internal combustion engine; Niedrigstemissionskonzept fuer einen wasserstoffbetriebenen Verbrennungsmotor

Energy Technology Data Exchange (ETDEWEB)

Fouquet, Marcel Christian Thomas

2012-03-15

This paper describes a concept with lowest emissions for a hydrogen internal combustion engine for passenger cars. With optimisation of the combustion concept the level of nitrogen oxide is below 90%, hydrocarbon and carbon monoxide below 99% of the SULEV target (CARB). This concept enables a potential in power density that is comparable to current supercharged combustion engines at lowest emission level without catalytic aftertreatment. Additionally with a catalytic aftertreatment system, the emission level of a current hydrogen combustion engine (mono-fuel) is lowered to a level, that this car can be labeled as air cleaning vehicle for hydrocarbons and carbon monoxide.

SODA-IIoT4ConnectedCars: Spread updates between cars with limited Internet access

OpenAIRE

Boudguiga , Aymen; Quesnel , Flavien; Bouzerna , Nabil

2017-01-01

International audience; A blockchain infrastructure, combined with cryptographic signatures, can improve availability and accountability for the deployment of IoT updates.However, cars with limited or intermittent Internet access may have difficulties in downloading full updates fromthe blockchain. Therefore, we allow cars that successfully downloaded updates to share them with other cars by means of a Peer-to-Peer (P2P) mechanism.

Vibration and acoustic characteristics of a city-car engine fueled with biodiesel blends

International Nuclear Information System (INIS)

Chiatti, Giancarlo; Chiavola, Ornella; Palmieri, Fulvio

2017-01-01

Highlights: • Investigation on the impact of UCO bends on the engine vibro-acoustic behavior. • The engine is mainly used in micro-cars in urban areas. • Data analysis to select the vibration/acoustic components related to the combustion. • Indicators used to evaluate the effect of blends on vibration and noise radiation. - Abstract: A number of studies have demonstrated that biodiesel is a more environmentally sustainable fuel than petroleum-derived fuels since it is a renewable source of energy and it allows to reduce undesired exhaust emissions (e.g. unburned HC, CO and particulate matter). However, specialized literature highlights there is still the need to further investigate performance, emissions and NVH characteristics of engines equipped with up-to-date technologies fueled with biodiesel blend. The aim of the present paper is to investigate the vibro-acoustic behavior of a small displacement engine, mainly employed in micro-cars, fueled with blends of distilled biodiesel (obtained from used cooking oil) and ultra low sulfur diesel fuel up to 40% by volume. Demands for reducing chemical and noise pollutions, traffic congestion and parking difficulties in urban areas make the micro-cars one of the possible solutions for the future urban environment, especially if the engine is fueled with biodiesel blends for their potential of reducing the pollutant emissions. An original methodology developed by the authors for in-cylinder pressure characterization via non-intrusive measurements is here applied to evaluate the impact of biodiesel content on the combustion process and therefore on engine vibration and noise emissions. The data processing in frequency domain allowed to extract the components mainly related to the combustion events. Concerning vibration signals: for all blends, the vibration amplitudes increases with the increase of engine speed values; B40 is characterized by highest values of RMS of accelerometer signal almost in the complete

GLYCAN-DIRECTED CAR-T CELLS.

Science.gov (United States)

Steentoft, Catharina; Migliorini, Denis; King, Tiffany R; Mandel, Ulla; June, Carl H; Posey, Avery D

2018-01-23

Cancer immunotherapy is rapidly advancing in the treatment of a variety of hematopoietic cancers, including pediatric acute lymphoblastic leukemia and diffuse large B cell lymphoma, with chimeric antigen receptor (CAR)-T cells. CARs are genetically encoded artificial T cell receptors that combine the antigen specificity of an antibody with the machinery of T cell activation. However, implementation of CAR technology in the treatment of solid tumors has been progressing much slower. Solid tumors are characterized by a number of challenges that need to be overcome, including cellular heterogeneity, immunosuppressive tumor microenvironment (TME), and, in particular, few known cancer-specific targets. Post-translational modifications that differentially occur in malignant cells generate valid cell surface, cancer-specific targets for CAR-T cells. We previously demonstrated that CAR-T cells targeting an aberrant O-glycosylation of MUC1, a common cancer marker associated with changes in cell adhesion, tumor growth, and poor prognosis, could control malignant growth in mouse models. Here, we discuss the field of glycan-directed CAR-T cells and review the different classes of antibodies specific for glycan-targeting, including the generation of high affinity O-glycopeptide antibodies. Finally, we discuss historic and recently investigated glycan targets for CAR-T cells and provide our perspective on how targeting the tumor glycoproteome and/or glycome will improve CAR-T immunotherapy. © The Author(s) 2018. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Variability in the primary emissions and secondary gas and particle formation from vehicles using bioethanol mixtures.

Science.gov (United States)

Gramsch, E; Papapostolou, V; Reyes, F; Vásquez, Y; Castillo, M; Oyola, P; López, G; Cádiz, A; Ferguson, S; Wolfson, M; Lawrence, J; Koutrakis, P

2018-04-01

Bioethanol for use in vehicles is becoming a substantial part of global energy infrastructure because it is renewable and some emissions are reduced. Carbon monoxide (CO) emissions and total hydrocarbons (THC) are reduced, but there is still controversy regarding emissions of nitrogen oxides (NO x ), aldehydes, and ethanol; this may be a concern because all these compounds are precursors of ozone and secondary organic aerosol (SOA). The amount of emissions depends on the ethanol content, but it also may depend on the engine quality and ethanol origin. Thus, a photochemical chamber was used to study secondary gas and aerosol formation from two flex-fueled vehicles using different ethanol blends in gasoline. One vehicle and the fuel used were made in the United States, and the others were made in Brazil. Primary emissions of THC, CO, carbon dioxide (CO 2 ), and nonmethane hydrocarbons (NMHC) from both vehicles decreased as the amount of ethanol in gasoline increased. NO x emissions in the U.S. and Brazilian cars decreased with ethanol content. However, emissions of THC, CO, and NO x from the Brazilian car were markedly higher than those from the U.S. car, showing high variability between vehicle technologies. In the Brazilian car, formation of secondary nitrogen dioxide (NO 2 ) and ozone (O 3 ) was lower for higher ethanol content in the fuel. In the U.S. car, NO 2 and O 3 had a small increase. Secondary particle (particulate matter [PM]) formation in the chamber decreased for both vehicles as the fraction of ethanol in fuel increased, consistent with previous studies. Secondary to primary PM ratios for pure gasoline is 11, also consistent with previous studies. In addition, the time required to form secondary PM is longer for higher ethanol blends. These results indicate that using higher ethanol blends may have a positive impact on air quality. The use of bioethanol can significantly reduce petroleum use and greenhouse gas emissions worldwide. Given the extent of

49 CFR 231.6 - Flat cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Flat cars. 231.6 Section 231.6 Transportation... TRANSPORTATION RAILROAD SAFETY APPLIANCE STANDARDS § 231.6 Flat cars. (Cars with sides 12 inches or less above the floor may be equipped the same as flat cars.) (a) Hand brakes—(1) Number. Same as specified for...

Engineering an Affordable Self-Driving Car

KAUST Repository

Budisteanu, Alexandru Ionut

2018-01-17

"More than a million people die in car accidents each year, and most of those accidents are the result of human errorﾔ Alexandru Budisteanu is 23 years old and owns a group of startups including Autonomix, an Artificial Intelligence software for affordable self-driving cars and he designed a low-cost self-driving car. The car\\'s roof has cameras and low-resolution 3D LiDAR equipment to detect traffic lanes, other cars, curbs and obstacles, such as people crossing by. To process this dizzying amount of data, Alexandru employed Artificial Intelligence algorithms to extract information from the visual data and plot a safe route for the car. Then, he built a manufacturing facility in his garage from Romania to assembly affordable VisionBot Pick and Place robots that are used to produce electronics. During this lecture, Alexandru will talk about this autonomous self-driving car prototype, for which he received the grand prize of the Intel International Science and Engineering Fair, and was nominated by TIME magazine as one of the worldﾒs most influential teens of 2013.

CAR-T cells are serial killers.

Science.gov (United States)

Davenport, Alexander J; Jenkins, Misty R; Ritchie, David S; Prince, H Miles; Trapani, Joseph A; Kershaw, Michael H; Darcy, Phillip K; Neeson, Paul J

2015-12-01

Chimeric antigen receptor (CAR) T cells have enjoyed unprecedented clinical success against haematological malignancies in recent years. However, several aspects of CAR T cell biology remain unknown. We recently compared CAR and T cell receptor (TCR)-based killing in the same effector cell and showed that CAR T cells can not only efficiently kill single tumor targets, they can also kill multiple tumor targets in a sequential manner. Single and serial killing events were not sustained long term due to CAR down-regulation after 20 hours.

Electric cars : The climate impact of electric cars, focusing on carbon dioxide equivalent emissions

OpenAIRE

Ly, Sandra; Sundin, Helena; Thell, Linda

2012-01-01

This bachelor thesis examines and models the emissions of carbon dioxide equivalents of the composition of automobiles in Sweden 2012. The report will be based on three scenarios of electricity valuation principles, which are a snapshot perspective, a retrospective perspective and a future perspective. The snapshot perspective includes high and low values for electricity on the margin, the retrospective perspective includes Nordic and European electricity mix and the future perspective includ...

Art Cars: Transformations of the Mundane

Science.gov (United States)

Stienecker, Dawn

2010-01-01

The automobile itself is often understood as an extension of oneself, where individuals may manipulate the interior and exterior of cars and trucks, decorating them through detailing, stickers, custom colors, and so on. Others go further and change their cars into unique works of art called art cars. Such cars break away from the banality of mass…

A comparative evaluation on the emission characteristics of ceramic and metallic catalytic converter in internal combustion engine

Science.gov (United States)

Leman, A. M.; Jajuli, Afiqah; Rahman, Fakhrurrazi; Feriyanto, Dafit; Zakaria, Supaat

2017-09-01

Enforcement of a stricter regulation on exhaust emission by many countries has led to utilization of catalytic converter to reduce the harmful pollutant emission. Ceramic and metallic catalytic converters are the most common type of catalytic converter used. The purpose of this study is to evaluate the performance of the ceramic and metallic catalytic converter on its conversion efficiency using experimental measurement. Both catalysts were placed on a modified exhaust system equipped with a Mitshubishi 4G93 single cylinder petrol engine that was tested on an eddy current dynamometer under steady state conditions for several engine speeds. The experimental results show that the metallic catalytic converter reduced a higher percentage of CO up to 98.6% reduction emissions while ceramic catalytic converter had a better reduction efficiency of HC up to 85.4% and 87.2% reduction of NOx.

ECOCURE BLUE – NEW COLD BOX SYSTEM WITH ULTRA-HIGH EFFICIENCY AND AS LOW AS POSSIBLE EMISSIONS

Directory of Open Access Journals (Sweden)

P. N. Vacelet

2018-01-01

Full Text Available By omitting materials subject to the labeling requirement in part 1 cold-box resin, Düker GmbH from Laufach can achieve an impressive reduction in emissions.Emission and workplace exposure limit values represent major challenges for foundries, and are becoming increasingly important due to every stricter statutory regulations. In particular, compliance with emission guidelines is essential in safeguarding company sites, and is now of equal significance as technical and economic issues. Modern foundries such as Düker GmbH from Laufachpursue a sustainable corporate policy in which the three pillars of cost-effectiveness, social responsibility and environmental protection are accorded equal importance. Düker’s example shows how the use of the new ECOCURE BLUE technology supports environmental protection and occupational health and safety, while also facilitating efficient, highly productive core production. 

Substitution between cars within the household

DEFF Research Database (Denmark)

De Borger, Bruno; Mulalic, Ismir; Rouwendal, Jan

2016-01-01

In this paper we study the demand for car kilometres in two-car households, focusing on the substitution between cars of different fuel efficiency in response to fuel price changes. We use a large sample of detailed Danish data on two-car households to estimate – for each car owned by the household...... – own and cross-price effects of increases in fuel costs per kilometre. The empirical results show that failure to capture substitution between cars within the household can result in substantial misspecification biases. Ignoring substitution, the basic model yielded fuel price elasticities of 0.......98 and 1.41 for the primary and secondary cars, respectively. Accounting for substitution effects, these figures reduce to, respectively, 0.32 and 0.45. Consistent with substitution behaviour, we find that the fuel price elasticity of fuel demand exceeds the elasticity of kilometre demands with respect...

49 CFR 238.311 - Single car test.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Single car test. 238.311 Section 238.311... Requirements for Tier I Passenger Equipment § 238.311 Single car test. (a) Except for self-propelled passenger cars, single car tests of all passenger cars and all unpowered vehicles used in passenger trains shall...

Strategies to control vehicular emissions: Indian scenario

Energy Technology Data Exchange (ETDEWEB)

Virupaksha, T. [Central Institute of Road Transport, Pune (India)

2002-07-01

The paper presents a common urban transport policy framework to protect the local and global environment and a state-of-the-art review of recommendations and measures suggested by the local administration in Indian cities from time to time. The measures to combat pollution in urban areas is identified by different cities but there is no cohesive strategy for implementing them. The pursuit of some of these measures are that the haphazard and piecemeal measures have not helped to gain optimum benefit possible or to make a discernible impact on mobility demand and vehicular emissions. A more practical strategy is required to reduce both emission and congestion, using a mixed set of instruments. The instruments are taxes on fuels, vehicles, and parking, incentives and regulations affecting vehicle ownership, usage and movement, traffic management more importantly encouraging non-motorized transport like bicycles by providing suitable lanes. Some of the policy measures seriously needed to be implemented to reduce ongoing pollution menace are enforcing higher maintenance standards, introducing vehicles designed to meet stricter emission standards, retrofitting vehicles to use other kinds of clean fuel, reducing urban congestion through transport management measures, scrapping highly polluting and high usage vehicles, and strengthening institutional links and regulatory issues. 5 refs., 1 tab.

ADULTEROUS BEHAVIOUR WITHIN THE CAR-OWNER COUPLE

Directory of Open Access Journals (Sweden)

Francis PAPON

2008-01-01

Full Text Available The objective of this paper was to analyse two activities: who rents a car and why? Which households share the driving of their cars? In order to do that, the Parc-Auto (Car-Fleet database, built from annual postal surveys conducted with a panel of 10,000 French households, has been processed. Among approximately one hundred questions in the survey, two key questions have been crossed against many social, economic, demographic, geographic or time variables. KQ1: “During the last 12 months, did you — or another person from your home — rent a car in France for personal purposes?” KQ2: “Is this car occasionally used by other persons?” Here are the main findings. Renting households are mainly working, high income households, living in the core of big cities, and in particular in Paris. Most of them have two wage-sheets and two cars, one of which is generally a recent, high power, high quality car. Car rental is mainly an occasional practice. Yet for a minority of renters, it is a sustained habit. Households with more licence holders than cars share the most: about three quarters of them share their cars. On the contrary, single driver-single car households have less opportunity to share: only 15% share. Household car sharing shed light on the gender role within households: while 58% of the main users of the shared cars are male, 55% of secondary users are female. Household car sharing is mainly a regular practice. Finally, without diminishing the merits of innovative transport solutions proposed here and there, it is not a waste of time to give some insight on self established behaviour within households. This reveals that complex patterns have been built over time by the people themselves, to cope with diverse situations that cannot be easily handled by straightforward classifications. The car cannot be reduced to a personal object. Household car sharing also carries strong links with the issue of car dependency. Sifting car

Clinical trials of CAR-T cells in China.

Science.gov (United States)

Liu, Bingshan; Song, Yongping; Liu, Delong

2017-10-23

Novel immunotherapeutic agents targeting tumor-site microenvironment are revolutionizing cancer therapy. Chimeric antigen receptor (CAR)-engineered T cells are widely studied for cancer immunotherapy. CD19-specific CAR-T cells, tisagenlecleucel, have been recently approved for clinical application. Ongoing clinical trials are testing CAR designs directed at novel targets involved in hematological and solid malignancies. In addition to trials of single-target CAR-T cells, simultaneous and sequential CAR-T cells are being studied for clinical applications. Multi-target CAR-engineered T cells are also entering clinical trials. T cell receptor-engineered CAR-T and universal CAR-T cells represent new frontiers in CAR-T cell development. In this study, we analyzed the characteristics of CAR constructs and registered clinical trials of CAR-T cells in China and provided a quick glimpse of the landscape of CAR-T studies in China.

Evaluation of the health impact of nanoparticles emitted from combustion sources: Comprehensive characterization of the physicochemical properties of nanoparticle emissions from wood combustion compliances, car- and ship diesel-engines as well as investigation of their toxicological effects on human lung cells and macrophages.

Science.gov (United States)

Zimmermann, R.; Dittmar, G.; Kanashova, T.; Buters, J.; Öder, S.; Paur, H. R.; Mülhopt, S.; Dilger, M.; Weiss, C.; Harndorf, H.; Stengel, B.; Hirvonen, M. R.; Jokiniemi, J.; Hiller, K.; Sapcariu, S.; Sippula, O.; Streibel, T.; Karg, E.; Weggler, B.; Schnelle-Kreis, J.; Lintelmann, J.; Sklorz, M.; Orasche, J.; Müller, L.; Passig, J.; Gröger, T.; BéruBé, K.; Krebs, T.

2016-12-01

Combustion emissions cause health effects. The HICE-Aerosol and Health project team studies the physicochemical properties as well as biological and toxicological effects on lung cells of combustion particle emissions. The chemical composition and physical parameters thoroughly characterized. Human lung cells are exposed to the diluted combustion exhaust fumes at the air-liquid interface (ALI), allowing a realistic lung-cell exposure by simulation of the lung situation. After exposure, cellular responses of the exposed lung cells are studied by multi-omics molecular biological analyses on transcriptomic, proteomic and metabolomic level. Emissions of wood combustion (log wood, pellet heater), ship diesel engines and car gasoline engines are addressed. Special field deployable ALI-exposition systems in a mobile S2-biological laboratory were set up and applied. Human alveolar epithelial cells (A549, BEAS2B and primary cells) as well as murine macrophages were ALI-exposed to diluted emissions. The cellular effects were then comprehensively characterized (viability, cyto-toxicology, multi-omics effects monitoring) and put in context with the chemical and physical aerosol data. The following order of overall cellular response-strength was observed: A relatively mild cellular effect is observed for the diluted wood combustion emissions. Interestingly the effects-strength for log-wood and pellet burner emissions are similar, although PM-concentrations are much higher for the log-wood heater. Similar mild biological effects are observed for the gasoline car emissions. The ship diesel engine emissions induced the most intense biological responses. A surprising result in this context is, that heavy fuel oil (HFO)-emissions showed lower biological effect strengths than the supposedly cleaner diesel fuel emissions (DF). The HFO-emission contain high concentrations of known toxicants (transition metals, polycyclic aromatics). This result was recently confirmed by experiments

'Diesel regenerativ' as fuel for passenger cars

Energy Technology Data Exchange (ETDEWEB)

Zimon, Anja; Krahl, Juergen [Coburg Univ. of Applied Sciences and Arts (Germany); Schroeder, Olaf; Fey, Barbara; Munack, Axel [Thuenen Institute, Braunschweig (Germany); Bockey, Dieter [Union for the Promotion of Oil and Protein Plants, Berlin

2013-06-01

Among the multitude of possible biofuels, hydrotreated vegetable oil (HVO) presents one possible means of partially replacing diesel fuel. In the project presented here, HVO was used with an admixture of biodiesel in the amount of 2% and 7% in two different vehicle fleets. HVO and biodiesel were made from domestic rapeseed oil. Both fuels trade under the name Diesel regenerative. The test vehicles were cars of the emission standards Euro 3 to Euro 6 that had been previously fueled with fossil diesel fuel, each for different periods. All vehicles were tested for regulated emissions at the beginning and the end of the project. In summary, emission reductions for hydrocarbons, carbon monoxide and particulate matter were identified for Diesel regenerative in comparison to fossil diesel fuel. However, nitrogen oxides were slightly increased for Diesel regenerative. Until now, this increase was only known in the literature to be associated with paraffinic fuel exhaust gases such as GTL. Moreover, decreases in nitrogen oxide when using pure HVO versus DF were published for utility vehicles (Warnecke et al., 2012). (orig.)

Clinical trials of CAR-T cells in China

Directory of Open Access Journals (Sweden)

Bingshan Liu

2017-10-01

Full Text Available Abstract Novel immunotherapeutic agents targeting tumor-site microenvironment are revolutionizing cancer therapy. Chimeric antigen receptor (CAR-engineered T cells are widely studied for cancer immunotherapy. CD19-specific CAR-T cells, tisagenlecleucel, have been recently approved for clinical application. Ongoing clinical trials are testing CAR designs directed at novel targets involved in hematological and solid malignancies. In addition to trials of single-target CAR-T cells, simultaneous and sequential CAR-T cells are being studied for clinical applications. Multi-target CAR-engineered T cells are also entering clinical trials. T cell receptor-engineered CAR-T and universal CAR-T cells represent new frontiers in CAR-T cell development. In this study, we analyzed the characteristics of CAR constructs and registered clinical trials of CAR-T cells in China and provided a quick glimpse of the landscape of CAR-T studies in China.

Chassis dynamometer study of emissions from 21 in-use heavy-duty diesel vehicles

International Nuclear Information System (INIS)

Yanowitz, J.; Graboski, M.S.; Ryan, L.B.A.; Alleman, T.L.; McCormick, R.L.

1999-01-01

Regulated emissions from 21 in-use heavy-duty diesel vehicles were measured on a heavy-duty chassis dynamometer via three driving cycles using a low-sulfur diesel fuel. Emissions of particulate matter (PM), nitrogen oxides (NO x ), carbon monoxide (CO), total hydrocarbon (THC), and PM sulfate fraction were measured. For hot start tests, emissions ranged from 0.30 to 7.43 g/mi (mean 1.96) for PM; 4.15--54.0 g/mi (mean 23.3) for NO x ; 2.09--86.2 g/mi (mean 19.5) for CO; and 0.25--8.25 g/mi (mean 1.70) for THC. When emissions are converted to a g/gal basis, the effect of driving cycle is eliminated for NO x and largely eliminated for PM. Sulfate comprised less than 1% of the emitted PM for all vehicles and test cycles. A strong correlation is observed between emissions of CO and PM. Cold starting at 77 F produced an 11% increase in PM emissions. Multivariate regression analyses indicate that in-use PM emissions have decreased at a slower rate than anticipated based on the stricter engine certification test standards put into effect since 1985. NO x emissions do not decrease with model year for the vehicles tested here. Smoke opacity measurements are not well correlated with mass emissions of regulated pollutants

A Joint Route Choice Model for Electric and Conventional Car Users

DEFF Research Database (Denmark)

Jensen, Anders Fjendbo; Rasmussen, Thomas Kjær; Prato, Carlo Giacomo

Introduction Worldwide, governments have committed to reducing air pollution and carbon emissions. With a higher share of renewable sources in the electricity production, battery electric cars (EVs) could play a significant role in maintaining these commitments. Growing literature shows...... an increasing interest in EVs and their market, but current EV travel demand studies are usually based on data collected from users of conventional gasoline or diesel engine cars (CVs) (see e.g. (Golob and Gould 1998; Pearre et al. 2011; Greaves et al. 2014). EVs are however different from CVs in a number...... effects, such as effects on the electricity network and the transport network. The objective of this study is to use revealed preferences (RP) data to investigate differences in route choice behaviour between CV and EV users. To our knowledge, this is the first time that a state-of-the-art route choice...

AAP Updates Recommendations on Car Seats

Science.gov (United States)

... Size Email Print Share AAP Updates Recommendations on Car Seats Page Content Article Body Children should ride ... of approved car safety seats. Healthy Children Radio: Car Seat Safety Dennis Durbin, MD, FAAP, lead author ...

Flexible injection control for fuel consumption and emission reduction in passenger cars?; Flexible Einspritzverlaufsformung: Auch bei PKW-Dieselmotoren ein wirkungsvolles Mittel zur Reduzierung von Verbrauch und Schadstoffemissionen?

Energy Technology Data Exchange (ETDEWEB)

Laumen, H.J.; Koerfer, T.; Lamping, M. [FEV Motorentechnik GmbH, Aachen (Germany); Pischinger, S.; Schmuecker, K.J. [RWTH Aachen (Germany). Lehrstuhl fuer Verbrennungskraftmaschinen

2007-07-01

In the recent decade the Diesel injection technology has been modified significantly. The old cam driven injection systems have been replaced nearly completely by modern Common Rail systems which enable a significantly higher degree of freedom especially with respect to multi-injection strategies and exhaust aftertreatment demands. Nevertheless, cam driven injection systems offered special characteristics which were favorable regarding fuel consumption and emissions. Due to the much higher nozzle opening and closing velocity, the seat throttling effects are widely reduced. Furthermore the fuel injection rate during ignition delay is smaller, compared to today's Common Rail systems. A new type of a piezoelectric Common Rail injector for passenger car engines, called FIRST (Flexible Injection Rate Shaping Tool) is described in this article, which combines both, the flexibility of modern Common Rail injectors as well as the benefits of cam driven injection systems regarding reduced seat throttling effects. Additionally flexible injection rate shaping is enabled by forming the slope of the actuator voltage. Both, the hydraulic behavior and also the engine performance with the new injector are presented in comparison to conventional injectors. The FIRST injector offers a benefit of 20% in PM and CO emission with constant NO{sub x} emission and reduced fuel consumption at part load as a result of the reduced seat throttling. By an optimization of the injection rate shape, the NO{sub x} emissions can be reduced by 40% at constant fuel consumption and PM emissions and without deterioration of NVH level. (orig.)

Seatbelts in CAR therapy: How Safe Are CARS?

Directory of Open Access Journals (Sweden)

Kentaro Minagawa

2015-05-01

Full Text Available T-cells genetically redirected with a chimeric antigen receptor (CAR to recognize tumor antigens and kill tumor cells have been infused in several phase 1 clinical trials with success. Due to safety concerns related to on-target/off-tumor effects or cytokine release syndrome, however, strategies to prevent or abate serious adverse events are required. Pharmacologic therapies; suicide genes; or novel strategies to limit the cytotoxic effect only to malignant cells are under active investigations. In this review, we summarize results and toxicities of investigations employing CAR redirected T-cells, with a focus on published strategies to grant safety of this promising cellular application.

Airborne Wear Particles Emissions fromCommercial Disc Brake Materials– Passenger Car Field Test

OpenAIRE

Wahlström, Jens; Olofsson, Ulf; Jansson, Anders; Olander, Lars

2008-01-01

Most modern passenger cars have disc brakes on the front wheels, which unlike drum brakes are not sealed off to the ambient air. During braking, there is wear to both the rotor and the pads. This wear process generates particles, which may become airborne. In field tests it is difficult to distinguish these particles from others in the surrounding environment. It may be preferable to use laboratory test stands where the cleanness of the surrounding air can be controlled. The validity of these...

Replacing car trips by increasing bike and public transport in the greater Barcelona metropolitan area: a health impact assessment study.

Science.gov (United States)

Rojas-Rueda, D; de Nazelle, A; Teixidó, O; Nieuwenhuijsen, M J

2012-11-15

Estimate the health risks and benefits of mode shifts from car to cycling and public transport in the metropolitan area of Barcelona, Spain. We conducted a health impact assessment (HIA), creating 8 different scenarios on the replacement of short and long car trips, by public transport or/and bike. The primary outcome measure was all-cause mortality and change in life expectancy related to two different assessments: A) the exposure of travellers to physical activity, air pollution to particulate matter car trips, starting and ending in Barcelona City, to cycling (n=141,690) would be for the travellers who shift modes 1.15 additional deaths from air pollution, 0.17 additional deaths from road traffic fatality and 67.46 deaths avoided from physical activity resulting in a total of 66.12 deaths avoided. Fewer deaths would be avoided annually if half of the replaced trips were shifted to public transport (43.76 deaths). The annual health impact in the Barcelona City general population (n=1,630,494) of the 40% reduction in car trips would be 10.03 deaths avoided due to the reduction of 0.64% in exposure to PM2.5. The deaths (including travellers and general population) avoided in Barcelona City therefore would be 76.15 annually. Further health benefits would be obtained with a shift of 40% of the car trips from the Greater Barcelona Metropolitan which either start or end in Barcelona City to public transport (40.15 deaths avoided) or public transport and cycling (98.50 deaths avoided).The carbon dioxide reduction for shifting from car to other modes of transport (bike and public transport) in Barcelona metropolitan area was estimated to be 203,251t/CO₂ emissions per year. Interventions to reduce car use and increase cycling and the use of public transport in metropolitan areas, like Barcelona, can produce health benefits for travellers and for the general population of the city. Also these interventions help to reduce green house gas emissions. Copyright © 2012

Fighting against VOC emissions; Lutter contre les emissions de COV

Energy Technology Data Exchange (ETDEWEB)

Fanlo, J.L. [Ecole des Mines d' Ales, 30 (France); Puech, G. [APAVE, 75 - Paris (France); Patoux, R. [Rhodia Rhoditech (France)] [and others

2001-12-01

This document brings together 15 testimonies of experts about the processes used in the industry for the abatement of volatile organic compound (VOC) emissions. The different points approached concern: the first industrial experiments of fight against VOC emissions, how to audit the facilities, how to make a diagnosis, to hierarchized and to measure continuously VOC emissions, how to anticipate the explosion risks linked with VOC treatment processes, the techniques of VOC abatement at the source implemented by industrialists, the implementation of an emission mastery scheme by Crow Cork and Seal company, the implementation of a solvent management plan by Turbomeca company and of a paints strategy by Renault car-making company, the combination of VOC abatement techniques implemented by industrialists, the classification of destruction and recovery processes: the experience feedback of Sanofi Synthelabo and of Air Liquide companies, the combination of upstream and downstream techniques implemented by Pechiney Rhenalu, Ashland Polyester and Quebecor companies. (J.S.)

Sulfur dioxide emissions and market effects under the Clean Air Act Acid Rain Program

International Nuclear Information System (INIS)

Zipper, C.E.; Gilroy, L.

1998-01-01

The Clean Air Act Amendments of 1990 (CAAA90) established a national program to control sulfur dioxide (SO 2 ) emissions from electricity generation. CAAA90's market-based approach includes trading and banking of SO 2 -emissions allowances. The paper presents an analysis of data describing electric utility SO 2 emissions in 1995, the first year of the program's Phase I, and market effects over the 1990-95 period. Fuel switching and flue-gas desulfurization were the dominant means used in 1995 by targeted generators to reduce emissions to 51% of 1990 levels. Flue-gas desulfurization costs, emissions allowance prices, low-sulfur coal prices, and average sulfur contents of coals shipped to electric utilities declined over the 1990-95 period. Projections indicate that 13-15 million allowances will have been banked during the programs' Phase I, which ends in 1999, a quantity expected to last through the first decade of the program's stricter Phase II controls. In 1995, both allowance prices and SO 2 emissions were below pre-CAAA90 expectations. The reduction of SO 2 emissions beyond pre-CAAA90 expectations, combined with lower-than-expected allowance prices and declining compliance costs, can be viewed as a success for market-based environmental controls. 21 refs., 6 figs., 3 tabs

In-use vs. type-approval fuel consumption of current passenger cars in Europe

International Nuclear Information System (INIS)

Ntziachristos, L.; Mellios, G.; Tsokolis, D.; Keller, M.; Hausberger, S.; Ligterink, N.E.; Dilara, P.

2014-01-01

In-use fuel consumption data of 924 passenger cars (611 petrol, 313 diesel) were collected from various European sources and were evaluated in comparison to their corresponding type-approval values. The analysis indicated that the average in-use fuel consumption was higher than the type-approval one by 11% for petrol cars and 16% for diesel cars. Comparison of this dataset with the Travelcard database in the Netherlands showed that the deviation increased for late model years and in particular for cars with low type-approval values. The deviation was higher than 60% for vehicles registered in 2012 within the 90–100 gCO 2 /km bin. Unrealistic vehicle resistances used in type-approval were identified as one of the prime reasons of the difference. A simplified linear model developed in the study may be used to predict in-use fuel consumption based on data publicly available. The model utilizes the fuel consumption measured in type-approval, the mass, and the engine capacity to provide in-use fuel consumption. This may be either used to correct fuel consumption factors currently utilized by emission models (e.g. COPERT, HBEFA, VERSIT+, and others) or could be used independently to make projections on how fuel consumption may develop on the basis of changing future passenger cars characteristics. - Highlights: • In-use fuel consumption of petrol and diesel passenger cars is 11% and 16% higher than type-approval, respectively. • The relative difference between in-use and type-approval increases for late model and vehicles with low consumption. • Unrealistically low vehicle resistances are identified as a prime reason of low type-approval fuel consumption. • A model developed predicts in-use consumption on the basis of type-approval consumption, vehicle mass, and engine capacity

Analysis of the energy and environmental effects of green car deployment by an integrating energy system model with a forecasting model

International Nuclear Information System (INIS)

Lee, Duk Hee; Park, Sang Yong; Hong, Jong Chul; Choi, Sang Jin; Kim, Jong Wook

2013-01-01

Highlights: ► A new methodology for improving energy system analysis models was proposed. ► The MARKAL model was integrated with the diffusion model. ► The new methodology was applied to green car technology. ► The ripple effect of green car technology on the energy system can be analyzed. -- Abstract: By 2020, Korea has set itself the challenging target of reducing nationwide greenhouse gas emissions by 30%, more than the BAU (Business as Usual) scenario, as the implementation goal required to achieve the new national development paradigm of green growth. To achieve such a target, it is necessary to diffuse innovative technologies with the capacity to drastically reduce greenhouse gas emissions. To that end, the ripple effect of diffusing innovative technologies on the energy and environment must be quantitatively analyzed using an energy system analysis model such as the MARKAL (Market Allocation) model. However, energy system analysis models based on an optimization methodology have certain limitations in that a technology with superior cost competitiveness dominates the whole market and non-cost factors cannot be considered. Therefore, this study proposes a new methodology for overcoming problems associated with the use of MARKAL models, by interfacing with a forecasting model based on the discrete-choice model. The new methodology was applied to green car technology to verify its usefulness and to study the ripple effects of green car technology on greenhouse gas reduction. The results of this study can be used as a reference when establishing a strategy for effectively reducing greenhouse gas emissions in the transportation sector, and could be of assistance to future studies using the energy system analysis model.

Parents smoking in their cars with children present.

Science.gov (United States)

Nabi-Burza, Emara; Regan, Susan; Drehmer, Jeremy; Ossip, Deborah; Rigotti, Nancy; Hipple, Bethany; Dempsey, Janelle; Hall, Nicole; Friebely, Joan; Weiley, Victoria; Winickoff, Jonathan P

2012-12-01

To determine prevalence and factors associated with strictly enforced smoke-free car policies among smoking parents. As part of a cluster, randomized controlled trial addressing parental smoking, exit interviews were conducted with parents whose children were seen in 10 control pediatric practices. Parents who smoked were asked about smoking behaviors in their car and receipt of smoke-free car advice at the visit. Parents were considered to have a "strictly enforced smoke-free car policy" if they reported having a smoke-free car policy and nobody had smoked in their car within the past 3 months. Of 981 smoking parents, 817 (83%) had a car; of these, 795 parents answered questions about their car smoking policy. Of these 795 parents, 29% reported having a smoke-free car policy, and 24% had a strictly enforced smoke-free car policy. Of the 562 parents without a smoke-free car policy, 48% reported that smoking occurred with children present. Few parents who smoke (12%) were advised to have a smoke-free car. Multivariable logistic regression controlling for parent age, gender, education, and race showed that having a younger child and smoking ≤10 cigarettes per day were associated with having a strictly enforced smoke-free car policy. The majority of smoking parents exposed their children to tobacco smoke in cars. Coupled with the finding of low rates of pediatricians addressing smoking in cars, this study highlights the need for improved pediatric interventions, public health campaigns, and policies regarding smoke-free car laws to protect children from tobacco smoke.

Aerodynamics of Race Cars

Science.gov (United States)

Katz, Joseph

2006-01-01

Race car performance depends on elements such as the engine, tires, suspension, road, aerodynamics, and of course the driver. In recent years, however, vehicle aerodynamics gained increased attention, mainly due to the utilization of the negative lift (downforce) principle, yielding several important performance improvements. This review briefly explains the significance of the aerodynamic downforce and how it improves race car performance. After this short introduction various methods to generate downforce such as inverted wings, diffusers, and vortex generators are discussed. Due to the complex geometry of these vehicles, the aerodynamic interaction between the various body components is significant, resulting in vortex flows and lifting surface shapes unlike traditional airplane wings. Typical design tools such as wind tunnel testing, computational fluid dynamics, and track testing, and their relevance to race car development, are discussed as well. In spite of the tremendous progress of these design tools (due to better instrumentation, communication, and computational power), the fluid dynamic phenomenon is still highly nonlinear, and predicting the effect of a particular modification is not always trouble free. Several examples covering a wide range of vehicle shapes (e.g., from stock cars to open-wheel race cars) are presented to demonstrate this nonlinear nature of the flow field.

Tickover speed controller for car engines

Energy Technology Data Exchange (ETDEWEB)

Hawk, R L

1980-05-22

In general, the tickover speed of a car engine is made sufficiently high, in order to permit an assumed maximum load to be taken from the engine at tickover. This setting of the tickover speed is usually done by stops in the fuel supply. Matching the actual load would lead to lower fuel consumption, without any danger of the engine stalling. The purpose of the invention is to provide a tickover speed controller, so that the tickover speed is adjusted by electronic control equipment, independently of the machine load. The fuel consumption on tickover is reduced and the emission of noxious substances is decreased. The electro-magnetic control of the throttle valve tickover setting is explained by extensive section drawings of the system. This process dispenses with the special tickover cams for a cold start.

Measurement of black carbon emissions from in-use diesel-electric passenger locomotives in California

Science.gov (United States)

Tang, N. W.; Kirchstetter, T.; Martien, P. T.; Apte, J.

2015-12-01

Black carbon (BC) emission factors were measured for a California commuter rail line fleet of diesel-electric passenger locomotives (Caltrain). The emission factors are based on BC and carbon dioxide (CO2) concentrations in the exhaust plumes of passing locomotives, which were measured from pedestrian overpasses using portable analyzers. Each of the 29 locomotives in the fleet was sampled on 4-20 separate occasions at different locations to characterize different driving modes. The average emission factor expressed as g BC emitted per kg diesel consumed was 0.87 ± 0.66 g kg-1 (±1 standard deviation, n = 362 samples). BC emission factors tended to be higher for accelerating locomotives traveling at higher speeds with engines in higher notch settings. Higher fuel-based BC emission factors (g kg-1) were measured for locomotives equipped with separate "head-end" power generators (SEP-HEPs), which power the passenger cars, while higher time-based emission factors (g h-1) were measured for locomotives without SEP-HEPs, whose engines are continuously operated at high speeds to provide both head-end and propulsion power. PM10 emission factors, estimated assuming a BC/PM10 emission ratio of 0.6 and a typical power output-to-fuel consumption ratio, were generally in line with the Environmental Protection Agency's locomotive exhaust emission standards. Per passenger mile, diesel-electric locomotives in this study emit only 20% of the CO2 emitted by typical gasoline-powered light-duty vehicles (i.e., cars). However, the reduction in carbon footprint (expressed in terms of CO2 equivalents) due to CO2 emissions avoidance from a passenger commuting by train rather than car is appreciably offset by the locomotive's higher BC emissions.

Ground effect aerodynamics of racing cars

OpenAIRE

Zhang, Xin; Toet, Willem; Zerihan, Jonathan

2006-01-01

We review the progress made during the last thirty years on ground effect aerodynamics associated with race cars, in particular open wheel race cars. Ground effect aerodynamics of race cars is concerned with generating downforce, principally via low pressure on the surfaces nearest to the ground. The “ground effected” parts of an open wheeled car's aerodynamics are the most aerodynamically efficient and contribute less drag than that associated with, for example, an upper rear wing. Whilst dr...

49 CFR 210.9 - Movement of a noise defective locomotive, rail car, or consist of a locomotive and rail cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Movement of a noise defective locomotive, rail car, or consist of a locomotive and rail cars. 210.9 Section 210.9 Transportation Other Regulations... locomotive, rail car, or consist of a locomotive and rail cars. A locomotive, rail car, or consist of a...

Spatio-temporal variation in soil derived nitrous oxide emissions under sugarcane

International Nuclear Information System (INIS)

Huang, Xiaodong; Grace, Peter; Mengersen, Kerrie; Weier, Keith

2011-01-01

Nitrous oxide (N 2 O) is a significant greenhouse gas with a global warming potential that is 300 times than that of carbon dioxide. Soil derived N 2 O emissions usually display a high degree of spatial and temporal variability because of their dependence on soil chemical and physical properties, and climate dependent environmental factors. However, there is little research that incorporates spatial dependence in the estimation of N 2 O emissions allowing for environmental factors in the same model. This study aims to examine the impact of two environmental factors (soil temperature and soil moisture) on N 2 O emissions and explore the spatial structure of N 2 O in the sub-tropical South East Queensland region of Australia. The replicated data on N 2 O emissions and soil properties were collected at a typical sugarcane land site covering 25 uniform grid points across 3600 m 2 between October 2007 and September 2008. A Bayesian conditional autoregressive (CAR) model was used to model spatial dependence. Results showed that soil moisture and soil temperature appeared to have substantially different effects on N 2 O emissions after taking spatial dependence into account in the four seasons. There was a substantial variation in the spatial distribution of N 2 O emission in the different seasons. The high N 2 O emission regions were accompanied by high uncertainty and changed in varying seasons in this study site. Spatial CAR models might be more plausible to elucidate and account for the uncertainty arising from unclear variables and spatial variability in the assessment of N 2 O emissions in soils, and more accurately identify relationships with key environmental factors and help to reduce the uncertainty of the soil parameters. - Highlights: → Soil moisture and soil temperature have substantially different effects on N 2 O emissions across four seasons of emissions. → High N 2 O emissions were associated with high uncertainty and varied between seasons. �

The kinematic advantage of electric cars

Science.gov (United States)

Meyn, Jan-Peter

2015-11-01

Acceleration of a common car with with a turbocharged diesel engine is compared to the same type with an electric motor in terms of kinematics. Starting from a state of rest, the electric car reaches a distant spot earlier than the diesel car, even though the latter has a better specification for engine power and average acceleration from 0 to 100 km h-1. A three phase model of acceleration as a function of time fits the data of the electric car accurately. The first phase is a quadratic growth of acceleration in time. It is shown that the tenfold higher coefficient for the first phase accounts for most of the kinematic advantage of the electric car.

Active deceleration support in car following

NARCIS (Netherlands)

Mulder, M.; Pauwelussen, J.J.A.; Paassen, M.M. van; Mulder, M.; Abbink, D.A.

2010-01-01

A haptic gas pedal feedback system is developed that provides car-following information via haptic cues from the gas pedal. During normal car-following situations, the haptic feedback (HF) cues were sufficient to reduce control activity and improve car-following performance. However, in more

Potential air pollutant emission from private vehicles based on vehicle route

Science.gov (United States)

Huboyo, H. S.; Handayani, W.; Samadikun, B. P.

2017-06-01

Air emissions related to the transportation sector has been identified as the second largest emitter of ambient air quality in Indonesia. This is due to large numbers of private vehicles commuting within the city as well as inter-city. A questionnaire survey was conducted in Semarang city involving 711 private vehicles consisting of cars and motorcycles. The survey was conducted in random parking lots across the Semarang districts and in vehicle workshops. Based on the parking lot survey, the average distance private cars travelled in kilometers (VKT) was 17,737 km/year. The machine start-up number of cars during weekdays; weekends were on average 5.19 and 3.79 respectively. For motorcycles the average of kilometers travelled was 27,092 km/year. The machine start-up number of motorcycles during weekdays and weekends were on average 5.84 and 3.98, respectively. The vehicle workshop survey showed the average kilometers travelled to be 9,510 km/year for motorcycles, while for private cars the average kilometers travelled was 21,347 km/year. Odometer readings for private cars showed a maximum of 3,046,509 km and a minimum of 700 km. Meanwhile, for motorcycles, odometer readings showed a maximum of 973,164 km and a minimum of roughly 54.24 km. Air pollutant emissions on East-West routes were generally higher than those on South-North routes. Motorcycles contribute significantly to urban air pollution, more so than cars. In this study, traffic congestion and traffic volume contributed much more to air pollution than the impact of fluctuating terrain.

Passenger car fuel consumption survey

Energy Technology Data Exchange (ETDEWEB)

1984-03-01

This survey originated from a proposal to monitor the fuel consumption and fuel economy of personal use passenger cars operated in Canada. Its purpose is to establish a data base which would contain information on total distance travelled, total amount of fuel consumed, average distance obtained per unit of fuel, total expenditures on fuel, and seasonal fluctuations in fuel consumption and in distance travelled. Among the needs served by this data base are the monitoring of passenger car fuel economy standards and the estimation of pasenger car fuel requirements in conditions involving fuel shortages. Survey methodology is by telephone interview to trace selected vehicles to the registered owners, at which time a fuel purchase diary is then mailed to the principal driver of the car. The results are tabulated on a quarterly basis and to be released as they become available in bulletins similar to this. Data are presented for each province and the total for Canada is given. During the fourth quarter of 1982, it is estimated that there were 7.3 million personal use passenger cars operated in Canada. These cars were driven 28 billion kilometers and consumed 4.3 billion litres of fuel. Their average litres/100 kilometres and the average fuel consumption was 590 litres. 8 tabs.

Danish emission inventories for road transport and other mobile sources

DEFF Research Database (Denmark)

Winther, M.

gasoline catalyst cars. For other mobile sources the fuel use, CO2 and NOX emissions have decreased with 15% from 1985 to 2002, and the PM emission decline is in the order of 13%. For SO2 the emission drop is 74% from 1985 to 2002, due to gradually lower fuel sulphur contents. In the same period...... the emissions of NMVOC and CO has increased with 32 and 6%, mainly due to the increased use of small gasoline boats. Uncertainties for the emissions and trends have been estimated...

An estimation of traffic related CO2 emissions from motor vehicles in the capital city of, Iran

Directory of Open Access Journals (Sweden)

Kakouei Aliakbar

2012-11-01

Full Text Available Abstract Vehicle exhaust is a major source of anthropogenic carbon dioxide (CO2 in metropolitan cities. Popular community mode (buses and taxies and about 2.4 million private cars are the main emission sources of air pollution in Tehran. A case survey has conducted to measure CO2 in four popular vehicles, bus, taxi, private car and motorcycle, which moved in the city with respectively 7800, 82358, 560000 and 2.4 million per day in 2012. Results indicated that the contribution of CO2 emissions increased in the following order: private car, motorcycle, bus and taxi. The overall average for the contribution of CO2 emissions in the private car, motorcycle, bus, and taxi were 26372, 1648, 1433 and 374 tons per day, respectively. Our results also showed that the urban transport operation consume an estimated 178 and 4224 million liter diesel and petrol per year, respectively, that have released about 10 million tons of CO2. The average contribution of CO2 emissions of private cars in Tehran was higher (88% than other vehicles. It was concluded that high volume of traffic, transport consumption of fossil fuels and shortage of adequate public transport system are responsible for the high CO2 level in environment in Tehran. Thus, it is to be expected that CO2 as a greenhouse gas has risen in Tehran more than ever in the following years and this would be a matter of concern for the authorities to have a comprehensive plan to mitigate this phenomena.

CAR SECURITY ENHANCEMENT IN PARKING AREAS

OpenAIRE

NANYONGA BERINDA; AYESIGA LINDSEY PATRA; BYEKWASO FAISAL; NATULINDA LADAN

2017-01-01

Over time, car thefts have been reported within Kampala parking areas. This has been majorly due to inefficient security measures of the available parking systems which focus mainly on the car and not the driver, making parking management a challenge. The focus of this survey was to explore the requirements of a new system called Car to Driver Matching Security System to enhance security of cars in Kampala, in particular, from the experience of 15 people. The data collected was then analyzed ...

Air pollutant and greenhouse gas emissions of passenger cars. A comparison of standard-based values and practical data per fuel type; Luchtvervuilende en klimaatemissies van personenauto's. Een vergelijking van norm- en praktijkwaarden per brandstofsoort

Energy Technology Data Exchange (ETDEWEB)

Van Essen, H.P.; Van Grinsven, A.H.; Hoen, M.J.J. ' t

2013-10-15

Although tax regulations provide an incentive for buying a car with reduced CO2 emissions, in the coming years the share of diesel vehicles in the business segment is likely to grow, thus unintentionally threatening air quality. This is because the NOx emissions of a modern Euro 5 diesel car are still very high in practice. Despite the NOx Euro standards for diesel vehicles having been substantially tightened since 1992, in practice there proves to have been very little progress, with Euro 5 diesel vehicles still emitting approximately the same amount of NOx as 21 years ago, as the present study shows [Dutch] De fiscale regels stimuleren de verkoop van auto's die minder CO2 uitstoten, maar zorgen de komende jaren naar verwachting voor een groei van het aandeel dieselauto's in het zakelijke segment. Deze groei vormt onbedoeld een bedreiging voor de luchtkwaliteit. Dit komt doordat de luchtvervuilende NOx-emissie van een moderne Euro 5-dieselauto's in de praktijk nog altijd erg hoog is. Ondanks dat de NOx-Euronormen voor diesels sinds 1992 flink zijn aangescherpt, blijkt in de praktijk dat er nauwelijks progressie is geboekt en dat een Euro 5-diesel nog steeds gemiddeld evenveel NOx-uitstoot als 21 jaar geleden.

30 CFR 57.19079 - Blocking mine cars.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Blocking mine cars. 57.19079 Section 57.19079... Hoisting Procedures § 57.19079 Blocking mine cars. Where mine cars are hoisted by cage or skip, means for blocking cars shall be provided at all landings and also on the cage. ...

30 CFR 56.19079 - Blocking mine cars.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Blocking mine cars. 56.19079 Section 56.19079... Hoisting Procedures § 56.19079 Blocking mine cars. Where mine cars are hoisted by cage or skip, means for blocking cars shall be provided at all landings and also on the cage. ...

Prediction of future car forms based on historical trends

Directory of Open Access Journals (Sweden)

Bijendra Kumar

2016-09-01

Full Text Available Cars are one of the most important products that affects our daily life. Manufacturers of cars are inclined to know factors that affect the sales of cars and how to influence them. Car is a very competitive product whose technology is already matured. Thus, purchase decisions of a car depend on factors such as, aesthetics, ergonomics, features available and price. Exterior form and colour of a car are the most important factors that influence likeness of the car. We did a case study on car aesthetics (form, colour, shape, and user focus with more than 500 car advertisements over the past 70 years, appearing in various car magazines. Results show that form of cars has changed from sharp to smooth over the years, and white colour cars are becoming more popular. Additionally, car size is becoming smaller and increasingly focused towards family. Thus, manufacturers are recommended to develop compact, efficient and hybrid cars.

49 CFR 174.57 - Cleaning cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Cleaning cars. 174.57 Section 174.57... and Loading Requirements § 174.57 Cleaning cars. All hazardous material which has leaked from a package in any rail car or on other railroad property must be carefully removed. ...

Car Builder: Design, Construct and Test Your Own Cars. School Version with Lesson Plans. [CD-ROM].

Science.gov (United States)

Highsmith, Joni Bitman

Car Builder is a scientific CD-ROM-based simulation program that lets students design, construct, modify, test, and compare their own cars. Students can design sedans, four-wheel-drive vehicles, vans, sport cars, and hot rods. They may select for aerodynamics, power, and racing ability, or economic and fuel efficiency. It is a program that teaches…

System for reducing emissions during coke oven charging

International Nuclear Information System (INIS)

Schuecker, Franz-Josef

2014-01-01

This article describes a process which reduces emissions from coke production in coke plants. The focus is on the charging process, which can be partly responsible for the fact that statutory emissions limits, which were originally met, are exceeded as coke plants get older. This article presents a solution in the form of a newly developed system that allows the oven charging system - the charging car - to respond to age-related changes in the geometry of a coke oven and thereby reduce the level of emissions.

A comprehensive experimental databank for the verification of urban car emission dispersion models

Energy Technology Data Exchange (ETDEWEB)

Pavageau, M.; Rafailidis, S.; Schatzmann, M. [Universitaet Hamburg (Germany). Meteorologisches Inst.

2001-07-01

A summary presentation is made of representative samples from a comprehensive experimental databank on car exhaust dispersion in urban street canyons. Physical modelling, under neutral stratification conditions, was used to provide visualisation, pollutant concentration and velocity measurements above and inside test canyons amidst surrounding urban roughness. The study extended to two different canyon aspects ratios, in combination with different roof configurations on the surrounding buildings. To serve as a reliable basis for validation and testing of urban pollution dispersion codes, special emphasis was placed in this work on data quality assurance. (Author)

Demonstration study on direct use of waste vegetable oil as car fuel

International Nuclear Information System (INIS)

Remoto, Yasuyuki; Zeeren, Nyamgerel; Ushiyama, Izumi

2009-01-01

Full text: Various kinds of vegetable oil and waste cooking oil are in fact used as car fuel all over the world. In general, 'bio-diesel' i.e. fatty acid methyl ester extracted from such oil is utilized as fuel for vehicles. However bio-diesel has some problems such as byproduct and waste materials created during transesterification. An alternative method is the direct use of vegetable oil as car fuel through installation of a heater unit in the car to decrease vegetable oil viscosity. However little data has been reported concerning this method. The authors of this study carried out performance tests on the direct use of waste cooking oil using a car with a heater unit and found its high potential. Moreover, the authors compared the environmental load of direct use with biodiesel and light oil by carrying out life cycle inventory to clarify the superiority of direct use. First, the authors made a car to test waste cooking oil as fuel by equipping a heater unit, filter and sub tank for light oil to a used Toyota Estima Diesel KD-CXR10G. The car can be driven on road using only waste cooking oil, although a little light oil is necessary for starting the engine. The authors, then, carried out chassis dynamo tests and on-road tests using the car. The car showed similar performance and could be driven on road for over half a year without any problems in both cases using either waste cooking oil or light oil as fuel. Next, authors carried out life cycle inventory and compared the environmental loads of direct use of waste cooking oil with biodiesel from waste cooking oil and light oil. The data for life cycle inventory were obtained from tests on direct use, from a factory in Japan for bio-diesel and from the Life Cycle Assessment Society of Japan database for light oil, respectively. The CO 2 emission rates were 73.9, 12.7 and 7.06 [kg-CO 2 / GJ] for light oil, bio-diesel from waste cooking oil and the direct use of waste cooking oil, respectively. The superiority of

Identification studies about take measures for mitigate of gas emissions greenhouse effect in energy Sector

International Nuclear Information System (INIS)

1999-11-01

In the Unit Nations Convention about Climatic change has get stability of greenhouse effects in atmosphere concentrations. In the framework to Uruguay Project URU/95/631 have been defined the need to identify, measures, practices, process and technologies for reduce some emissions furthermore in Energy sector. Emission impact, cost-benefit, direct or iundirect, national programs, factibility such as social, politics and Institutional agreements was considered in the present work. It was given emissions proyected for 15 years period 1999-2013 of the following atmospheric pollutants: carbon dioxide,carbon monoxide, nitrogen oxides, sulfur oxides and methane.Eight stages was applied the emission evaluation: natural gas; without natural gas; transport; industrial; Montevidean bus- car demand; natural gas uses in bus-taxi; nitrogen oxides control in thermic centrals; catalytic converters in gasoline cars

CAN PUBLIC TRANSPORT COMPETE WITH THE PRIVATE CAR?

Directory of Open Access Journals (Sweden)

Linda STEG

2003-01-01

Full Text Available Public transport is often perceived to be a poor alternative for car use. This paper describes who may be open to use public transport more often, and how people might be persuaded to use it. A computerised questionnaire study was conducted among 1,803 Dutch respondents in May 2001. Results revealed that especially fervent car users disliked public transport. For them, the car outperformed public transport not only because of its instrumental function, but also because the car represents cultural and psychological values, e.g. the car is a symbol of freedom and independence, a status symbol and driving is pleasurable. So, for fervent car users, car use is connected with various important values in modern society. Infrequent car users judged less positively about the car and less negatively about public transport. Consequently, they may be open to use public transport more regularly. In contrast, many efforts are needed to stimulate fervent car users to travel by public transport, because in their view, public transport cannot compete with their private car. In this case, policies should be aimed at reducing the functional, psychological and cultural values of private cars, as well as increasing the performance of public transport and other (more environmentally sound modes of transport on these aspects.

Solar Powered Heat Control System for Cars

OpenAIRE

Abin John; Jithin Thomas

2014-01-01

It takes times for an air-conditioner to effectively start cooling the passenger compartment in the car. So the passenger of the car will feel the heat in the car extremely before the air-conditioner fully cooling the interior of the car. Excessive heat can also damage an automobile's interior as well as personal property kept in the passenger compartment. So, a system to reduce this excessive heat by pumping out hot air and allowing cooler ambient air to enter the car by mean...

Flying car design and testing

OpenAIRE

Klein, S.; Smrcek, L.

2009-01-01

This paper is primarily concerned with the inverted design process and manufacture of a flying car prototype which can overcome the problem of traffic management in the world today. A possible solution to the problem of overcrowded roads would be to design a flying or hovering car. Given technological advances in aircraft construction, navigation and operation, flying cars or personal aircraft are now a feasible proposition. The viability of such a concept was investigated in terms of produci...

Fuel consumption rates of passenger cars in China: Labels versus real-world

International Nuclear Information System (INIS)

Huo Hong; Yao Zhiliang; He Kebin; Yu Xin

2011-01-01

Recently, China has implemented many policy measures to control the oil demand of on-road vehicles. In 2010, China started to report the fuel consumption rates of light-duty vehicles tested in laboratory and to require new vehicles to show the rates on window labels. In this study, we examined the differences between the test and real-world fuel consumption of Chinese passenger cars by using the data reported by real-world drivers on the internet voluntarily. The sales-weighted average fuel consumption of new cars in China in 2009 was 7.80 L/100 km in laboratory and 9.02 L/100 km in real-world, representing a difference of 15.5%. For the 153 individual car models examined, the real-world fuel consumption rates were -8 to 60% different from the test values. The simulation results of the International Vehicle Emission model show that the real-world driving cycles in 22 selected Chinese cities could result in -8 to 34% of changes in fuel consumption compared to the laboratory driving cycle. Further government effort on fuel consumption estimates adjustment, local driving cycle development, and real-world data accumulation through communication with the public is needed to improve the accuracy of the labeling policy. - Research highlights: → China requires new cars sold to show the test fuel use levels on window labels. → Real-world fuel consumption rates of cars are 15.5% higher than the label values. → Discrepancy between the test cycle and real conditions is a major cause for the gap. → China should adjust the estimates, collect fuel use data, and develop driving cycles. → More official and academic efforts are needed to improve the labeling policy.

49 CFR 180.507 - Qualification of tank cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Qualification of tank cars. 180.507 Section 180... QUALIFICATION AND MAINTENANCE OF PACKAGINGS Qualification and Maintenance of Tank Cars § 180.507 Qualification of tank cars. (a) Each tank car marked as meeting a “DOT” specification or any other tank car used...

Emission Reduction Potential with the Renewal of the Vehicle Fleet in Croatia

International Nuclear Information System (INIS)

Zidov, B.; Brlek, G.; Brajkovic, J.; Karan, M.

2015-01-01

The European Union has identified the typical areas of application of measures to tackle the problem of pollutants emissions into the air. Road transport is recognized as the largest polluter of the environment and an increase in CO2 emissions is most difficult to suppress in this type of transport. Looking at the projected trend of emission reductions in Croatia, it is clear that for achieving the minimum targets by 2050, as proposed by the European Union, implementation of the very strong measures in the coming period will be inevitable. The main aim of the paper refers to the analysis of potential emission reduction of pollutants generated by passenger vehicles registered in Croatia, assuming the implementation of measures that will result in technological renewal of the fleet at the national level. Generally considering, passenger cars before the Euro 1 standard, Euro 1 and Euro 2 standards together emit nearly 40 percent of all CO2 emissions generated by passenger cars registered in Croatia. Assuming replacement of all cars up to and including Euro 2, with Euro 6 vehicles, and taking into account certain assumptions, the potential reductions in emissions of NOx, CO, CH4 and particles were quantified. The potential reduction in NOx emissions is approximately 3,061 tons, in CO emissions approximately 14482 tons, in CH4 approximately 114 tons and in particulate matter approximately 257 tons. Depending on the engine size, with the replacement of the typical gasoline 20 years old passenger vehicle with the new one, without changing the driving mode, annual savings of up to 209 liters of gasoline fuel and reduction of CO2 emissions by 475 kg could be achieved (according to the assumptions described in the paper). With the replacement of diesel vehicles under the same conditions, the savings of up to 311 liters of diesel fuel annually and reduction of CO2 emissions by 815 kg could be achieved. (author).

Car sharing à la carte

CERN Multimedia

Anaïs Schaeffer

2012-01-01

Do you want to make your commute to CERN easier, while saving money at the same time? Would you prefer not to spend a quarter of an hour crawling round the CERN car parks looking for a space? If so, read on: this article might well be of great interest to you.   We would like to draw your attention to a well established, albeit sadly under-used, method of transport: car sharing. To promote car-sharing, the GS Department has stepped in to call on the services of the Swiss firm Green Monkeys which specialises in this user-friendly and intelligent transport scheme. The company’s slogan is:  “Car-sharing as you want, when you want and as much as you want”. The principle is very straightforward. To use this car-sharing facility, you simply complete your free online registration with Green Monkeys, providing the following details: your journey, departure time, arrival time and days of the week, and indicating whether you are a passenger or driver or both. &a...

Consumer Behavior towards Safer Car Purchasing Decisions

Directory of Open Access Journals (Sweden)

Khairil Anwar Abu Kassim

2016-08-01

Full Text Available In Malaysia, the car safety level has been elevated through regulations and a consumer-based approach, i.e. the New Car Assessment Program in Southeast Asian Countries (ASEAN NCAP. Nevertheless, the availability of information on consumers’ car purchasing decisions towards safety is still limited in Malaysia. Thus, this study was aimed at evaluating consumers’ purchasing decisions of their present cars and investigating their awareness of ASEAN NCAP. Self-administered questionnaires were distributed among consumers visiting different car showrooms and dealer shops. The findings suggest that safety was considered as one of the top three factors by the respondents when purchasing their present cars. Awareness of ASEAN NCAP has increased as compared to a previous study. This information is essential for policy makers, manufacturers and other stakeholders to assist in setting priorities with regard to the promotion of car safety in the country.

Environmental labeling of car tires--toxicity to Daphnia magna can be used as a screening method.

Science.gov (United States)

Wik, Anna; Dave, Göran

2005-02-01

Car tires contain several water-soluble compounds that can leach into water and have toxic effects on aquatic organisms. Due to tire wear, 10,000 tonnes of rubber particles end up along the Swedish roads every year. This leads to a diffuse input of emissions of several compounds. Emissions of polyaromatic hydrocarbons (PAHs) are of particular concern. PAHs are ingredients of the high aromatic oil (HA oil) that is used in the rubber as a softener and as a filler. The exclusion of HA oils from car tires has started, and an environmental labeling of tires could make HA oils obsolete. The toxicity to Daphnia magna from 12 randomly selected car tires was tested in this study. Rubber from the tread of the tires was grated into small pieces, to simulate material from tire wear, and the rubber was equilibrated with dilution water for 72 h before addition of test organisms. The 24-h EC50s of the rubber pieces ranged from 0.29 to 32 gl-1, and the 48-h EC50s ranged from 0.0625 to 2.41 gl-1. Summer tires were more toxic than winter tires. After the 48-h exposure, the daphnids were exposed to UV-light for 2 h, to determine if the tires contained compounds that were phototoxic. After UV-activation the EC50s ranged from 0.0625 to 0.38 gl-1. Four of the 12 tires had a very distinct photoactivation, with a toxicity increase of >10 times. This study has shown that the used method for toxicity testing with Daphnia magna according to ISO 6341 could be used as a basis for environmental labeling of car tires.

Stock-car racing makes intuitive physicists

Science.gov (United States)

Gwynne, Peter

2008-03-01

Formula One races involve cars festooned with gadgets and complex electronic devices, in which millions of dollars are spent refining a vehicle's aerodynamics and reducing its weight. But in events run by America's National Association of Stock Car Auto Racing (NASCAR), cars hurtle round an oval track at speeds of about 300 km h-1 without the help of the complex sensors that are employed in Formula One cars. To avoid crashing, drivers must make their own adjustments to track conditions, engine problems and the traffic around them.

Divorce your car: ending the love affair with the automobile

Energy Technology Data Exchange (ETDEWEB)

Alvord, K.

2000-07-01

This book is a guide for people wishing to liberate themselves from their addiction to cars and the automobile culture. It is a repository of examples and actions that individuals and communities can take to reduce dependence on the automobile. The range of possibilities run from using cars less to not owning one at all. The book provides a humorous yet clear-headed approach to a greener world and maps out the road to how people can live happily ever after by breaking free of 'auto-cracy', without insisting on people in car-dependent countries quit their automotive addiction instantly. Nevertheless, it clearly articulates the connection between automobiles, their arteries (i.e. highways) and effluents (i.e. greenhouse gases and particulate emissions), and the increasing number and severity of natural disasters between the urban renewal and freeway construction that, in the author's view, helped ignite the riots in Watts, Newark and Detroit. The disastrous societal and geophysical effects of the automobile are demonstrated in great abundance, and the mountain of evidence of the systematic abuse of the planet that the book provides is a stunning refutation of the notion that technology is neutral. The automobile is accused of being not only the linchpin of Western and primarily American industrialism and resource extraction, it is also accused of being the chief suspect in a century-long theft of time, conviviality and beauty. How to bring about a change in people's love affair with their cars is difficult to comprehend but this author has a multitude of useful suggestions which seem to suggest that it is possible. There is a list of 104 'selected references' and an extensive list of 'other resources'.

Use of videoconferencing in Wales to reduce carbon dioxide emissions, travel costs and time.

Science.gov (United States)

Lewis, Delyth; Tranter, Glynis; Axford, Alan T

2009-01-01

In September 2005 a telemedicine service was started to assist multidisciplinary teams in Wales to improve cancer services. In October 2006 and October 2007 users of videoconferencing equipment at one site completed questionnaires. During October 2006 a total of 18,000 km of car travel were avoided, equivalent to 1696 kg of CO(2) emission. During October 2007 a total of 20,800 km of car travel were avoided, equivalent to 2590 kg of CO(2) emission. We estimate that 48 trees would take a year to absorb that quantity of CO(2). The results of the surveys show that exploiting telemedicine makes better use of staff time, reduces the time spent travelling and assists in reducing climate change by limiting the emissions of CO(2).

Estimation of Turkish road transport emissions

International Nuclear Information System (INIS)

Soylu, Seref

2007-01-01

Using the COPERT III program, an inventory of Turkish road transport emissions was calculated and the contributions of road transport to global and local air pollutant emissions were examined for the year 2004. It was observed that passenger cars are the main source of CO, HC, and Pb emissions while heavy duty vehicles are mainly responsible for NO x , particulate matter (PM), and SO 2 emissions. Taking the emissions for the year 2004 as the baseline, a parametric study was conducted to determine the emission reduction potentials of different road transport strategies. The results indicated that the following road transport strategies; fleet renewal, promotion of public transportation, and faster urban traffic speed are very effective strategies for reducing regulated emissions and fuel consumption (FC) from a technical point of view. It was also noted that replacement of two-stroke motorcycles with four-stroke motorcycles is as effective as fleet renewal in reducing HC emissions

Electric Cars and Oil Prices

OpenAIRE

Azar, Jose

2009-01-01

This paper studies the joint dynamics of oil prices and interest in electric cars, measured as the volume of Google searches for related phrases. Not surprisingly, I find that oil price shocks predict increases in Google searches for electric cars. Much more surprisingly, I also find that an increase in Google searches predicts declines in oil prices. The high level of public interest in electric cars between April and August of 2008 can explain approximately half of the decline in oil prices...

Research of braking peculiarities of used cars

Directory of Open Access Journals (Sweden)

V. Mitunevičius

2002-06-01

Full Text Available This paper briefly describes some analysis of a car braking process - the peculiarities of car wheel-to-road adhesion, the influence of distribution of braking forces on car stability between front and rear axles. The requirements of EU Directive 71/320/EEC to braking force coefficients of car front and rear axles are exposed. Structural designs of braking systems are analyzed with respect to their meeting the EU standards. Experimental measurements of braking force coefficients for some models of cars which are used in Lithuania, are presented with the analysis how these coefficients meet the EU standards. The analysis of test results, suggestions for the ratio of braking forces of car front and rear axles are presented.

On the way to 130 g CO2/km-Estimating the future characteristics of the average European passenger car

International Nuclear Information System (INIS)

Fontaras, Georgios; Samaras, Zissis

2010-01-01

A new average CO 2 emissions limit for passenger cars was introduced in EU in 2009 imposing gradual average CO 2 emissions reduction to 130 g/km until 2015. This paper attempts to study possible changes in vehicle characteristics for meeting this limit taking into account the average European passenger car of 2007-2008. For this purpose first the most important factors affecting vehicle fuel consumption over the reference cycle (NEDC) are identified. At a second step, the CO 2 benefit from the optimisation of these factors is quantified, through simulations of 6 different passenger cars commonly found in the European fleet. For the simulations Advisor 2002 was employed and validated against published type approval data. The analysis indicated that substantial reductions in vehicle weight, tyre rolling resistance and engine efficiency are necessary to reach even the 2008 target. A 10% reduction in average vehicle weight combined with 10% better aerodynamic characteristics, 20% reduced tyre rolling resistance and a 7.5% increase in average powertrain efficiency can lead to CO 2 reductions of approximately 13% (about 138 g/km based on 2007-2008 fleet-wide performance). Complying with the 130 g/km within the next six-year timeframe will be a rather difficult task and additional technical measures appear to be necessary.

Car stickers for 2009

CERN Multimedia

TS Department

2008-01-01

All members of the personnel holding a valid contract (except owners of cars with green or CD plates) can come to the Registration Service (Building 55, 1st floor) to obtain their 2009 car sticker, Mondays to Fridays from 7.30 a.m. to 4.00 p.m. non-stop. Please ensure you bring with you the documents relating to the vehicles(s) concerned. If you only wish to register one vehicle, you can obtain the 2009 sticker using the request form on the Web (via internet Explorer only). NB: This notice only applies to members of the personnel who obtained one or several blue car stickers for 2008. Reception and Access Control Service – TS/FM

Preferences for Alternative Fuel Vehicles of Company Car Drivers

NARCIS (Netherlands)

Koetse, M.J.; Hoen, A.

2014-01-01

Costs of car ownership for company cars drivers and private car owners are very different. Car use, car choice decisions and preferences for car characteristics may therefore differ substantially between these two markets. In this paper, we present results of a study on the preferences of company

The trend of the total stock of the private car-petrol in Spain: Stochastic modelling using a new gamma diffusion process

International Nuclear Information System (INIS)

Gutierrez, R.; Gutierrez-Sanchez, R.; Nafidi, A.

2009-01-01

The main aim of this study is to model the trend of the evolution of the total stock of private petrol-driven cars. In Spain, as in other EU countries, this trend between 2000 and 2005 differed significantly from that observed from 1986 to 1999. Moreover, it varies greatly from that corresponding to the stock of diesel-driven cars, which consistently presents an exponential Gompertz-type increase. Spain constitutes a typical example of a failure to observe the maximum CO 2 emission levels assigned to it by 2012 under the Kyoto Protocol (1992); a significant percentage of these excess emissions is accounted for by the land transport sector, in general, and by the private cars subsector, in particular. This paper proposes a stochastic model based on a new non homogeneous stochastic gamma-type diffusion process which it is a stochastic version of a Gamma function type deterministic growth model considered in Skiadas . We describe its main probabilistic characteristics and establish a statistical methodology by which it can be fitted to real data and obtain medium-term forecasts that, in statistical terms, are quite accurate

The Electric Cars Challenge

Science.gov (United States)

Roman, Harry T.

2011-01-01

Over 100 years ago, the great inventor Thomas Edison warned that gasoline cars would pollute the environment and lead to gasoline shortages. He preferred the use of clean electric vehicles. He also put his money where his mouth was and developed an entirely new alkaline storage battery system for his beloved cars, the nickel-iron storage battery.…

49 CFR 231.8 - Tank cars without side sills and tank cars with short side sills and end platforms.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Tank cars without side sills and tank cars with... APPLIANCE STANDARDS § 231.8 Tank cars without side sills and tank cars with short side sills and end platforms. (a) Hand brakes—(1) Number. Same as specified for “Box and other house cars” (see § 231.1(a)(1...

Emission Characteristics of Gas-Fired Boilers based on Category-Specific Emission Factor from Field Measurements in Beijing, China

Science.gov (United States)

Itahashi, S.; Yan, X.; Song, G.; Yan, J.; Xue, Y.

2017-12-01

Gas-fired boilers will become the main stationary sources of NOx in Beijing. However, the knowledge of gas-fired boilers in Beijing is limited. In the present study, the emission characteristics of NOx, SO2, and CO from gas-fired boilers in Beijing were established using category-specific emission factors (EFs) from field measurements. In order to obtain category-specific EFs, boilers were classified through influence analysis. Factors such as combustion mode, boiler type, and installed capacity were considered critical for establishing EFs because they play significant roles in pollutant formation. The EFs for NOx, CO, and SO2 ranged from 1.42-6.86 g m-3, 0.05-0.67 g m-3 and 0.03-0.48 g m-3. The emissions of NOx, SO2, and CO for gas-fired boilers in Beijing were 11121 t, 468 t, and 222 t in 2014, respectively. The emissions were spatially allocated into grid cells with a resolution of 1 km × 1 km, and the results indicated that top emitters were in central Beijing. The uncertainties were quantified using a Monte Carlo simulation. The results indicated high uncertainties in CO (-157% to 154%) and SO2 (-127% to 182%) emissions, and relatively low uncertainties (-34% to 34%) in NOx emission. Furthermore, approximately 61.2% and 96.8% of the monitored chamber combustion boilers (CCBs) met the standard limits for NOx and SO2, respectively. Concerning NOx, low-NOx burners and NOx emission control measures are urgently needed for implementing of stricter standards. Adopting terminal control measures is unnecessary for SO2, although its concentration occasionally exceeds standard limits, because reduction of its concentration can be achieved thorough control of the sulfur content of natural gas at a stable low level. Furthermore, the atmospheric combustion boilers (ACBs) should be substituted with CCBs, because ACBs have a higher emission despite lower gross installed capacity. The results of this study will enable in understanding and controlling emissions from gas

Real-time measurements of nitrogen oxide emissions from in-use New York City transit buses using a chase vehicle.

Science.gov (United States)

Shorter, Joanne H; Herndon, Scott; Zahniser, Mark S; Nelson, David D; Wormhoudt, Joda; Demerjian, Kenneth L; Kolb, Charles E

2005-10-15

New diesel engine technologies and alternative fuel engines are being introduced into fleets of mass transit buses to try to meet stricter emission regulations of nitrogen oxides and particulates: Real-time instruments including an Aerodyne Research tunable infrared laser differential absorption spectrometer (TILDAS) were deployed in a mobile laboratory to assess the impact of the implementation of the new technologies on nitrogen oxide emissions in real world driving conditions. Using a "chase" vehicle sampling strategy, the mobile laboratory followed target vehicles, repeatedly sampling their exhaust. Nitrogen oxides from approximately 170 in-use New York City mass transit buses were sampled during the field campaigns. Emissions from conventional diesel buses, diesel buses with continuously regenerating technology (CRT), diesel hybrid electric buses, and compressed natural gas (CNG) buses were compared. The chase vehicle sampling method yields real world emissions that can be included in more realistic emission inventories. The NO, emissions from the diesel and CNG buses were comparable. The hybrid electric buses had approximately one-half the NOx emissions. In CRT diesels, NO2 accounts for about one-third of the NOx emitted in the exhaust, while for non-CRT buses the NO2 fraction is less than 10%.

CARS 2009. Computer assisted radiology and surgery. Proceedings

International Nuclear Information System (INIS)

Anon.

2009-01-01

The CARS 2009 proceedings include contributions and poster sessions concerning different conferences and workshops: computer assisted radiology, 23rd international congress and exhibition, CARS clinical day, 13th annual conference of the international society for computer aided surgery, 10th CARS/SPIE/EuroPACS joint workshop on surgical PACS and the digital operating, 11th international workshop on computer-aided diagnosis, 15th computed maxillofacial imaging congress, CARS - computer assisted radiology and surgery, 1st EPMA/CARS workshop on personalized medicine and ICT, JICARS - Japanese institutes of CARS, 1st EuroNotes/CTAC/CARS workshop on NOTES: an interdisciplinary challenge, 13th annual conference for computer aided surgery, 27th international EuroPACS meeting.

IL-7 and CCL19 expression in CAR-T cells improves immune cell infiltration and CAR-T cell survival in the tumor.

Science.gov (United States)

Adachi, Keishi; Kano, Yosuke; Nagai, Tomohiko; Okuyama, Namiko; Sakoda, Yukimi; Tamada, Koji

2018-04-01

Infiltration, accumulation, and survival of chimeric antigen receptor T (CAR-T) cells in solid tumors is crucial for tumor clearance. We engineered CAR-T cells to express interleukin (IL)-7 and CCL19 (7 × 19 CAR-T cells), as these factors are essential for the maintenance of T-cell zones in lymphoid organs. In mice, 7 × 19 CAR-T cells achieved complete regression of pre-established solid tumors and prolonged mouse survival, with superior anti-tumor activity compared to conventional CAR-T cells. Histopathological analyses showed increased infiltration of dendritic cells (DC) and T cells into tumor tissues following 7 × 19 CAR-T cell therapy. Depletion of recipient T cells before 7 × 19 CAR-T cell administration dampened the therapeutic effects of 7 × 19 CAR-T cell treatment, suggesting that CAR-T cells and recipient immune cells collaborated to exert anti-tumor activity. Following treatment of mice with 7 × 19 CAR-T cells, both recipient conventional T cells and administered CAR-T cells generated memory responses against tumors.

How does Euro NCAP results correlate to real life injury risks - a paired comparison study of car-to-car crashes in Sweden