WorldWideScience

Sample records for stretched-membrane dish program

  1. Facet development for a faceted stretched-membrane dish by Solar Kinetics, Inc

    Energy Technology Data Exchange (ETDEWEB)

    Schertz, P.T.; Brown, D.C.; Konnerth, A. III (Solar Kinetics, Inc., Dallas, TX (United States))

    1991-07-01

    A 3.6-meter diameter stretched-membrane optical facet for a parabolic dish has been successfully designed and demonstrated under contract with Sandia National Laboratories. Twelve facets identical to them will be used to make the lightweight reflector of the dish. The project goal of 2.5-mrad surface accuracy was met with each of the two full-sized prototypes, and accuracies of as low as 1.1 mrad were achieved. The facet weight is 11.7 kg/m{sup 2} (2.4lbs/ft{sup 2}). The facet is similar in construction to the successful stretched-membrane heliostat; it has two thin metal membranes attached to a ring. However, the front membrane for this facet is plastically formed at the factor in order to achieve a shorter facet f/D (approximately 3.0). A passive tether restrains the from membrane when not in operation, that is, when the stabilizing vacuum is off. The optical surface is achieved with a silvered-acrylic film laminated to the metal membrane. The facet is expected to cost $55.40/m{sup 2} at a production rate of 10,000 facets per year and $115, 000/m{sup 2}-at a production rate of 500 facets a year. Several key issues have been resolved. Stress concentrations due to seams in the reflective laminate did not cause membrane rupture during forming as they have for dishes with lower focal length-to-diameter ratios. The laminate survived the forming process and simulated operation without deterioration. The optical effect of the tether on the membrane was tested and found to be very small. Most important, highly accurate shapes were obtained using a simple forming procedure. Additional tests are needed to demonstrate process repeatablility and facet performance in typical operating conditions. 18 refs., 36 figs., 11 tabs.

  2. Detail design of a 10.4-m stretched-membrane dish. Phase 2, Final report

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    This report describes efforts conducted under Tasks 3 and 4 of the second phase of the project to develop a single-element stretched-membrane dish concept to reduce the cost of a high-performance concentrating solar collector. We completed the detailed design for such a collector suitable to drive a 25-kWe Stirling motor generator. The design includes the collectors, optical element, the drive, and support systems. The aperture of the optical element was sized to provide the required energy to the engine based on test data and analytical models of the concentrator receiver, and engine. The design of the optical element was improved based on experience gained from the design, fabrication, and testing of several prototypes.

  3. Fifth parabolic dish solar thermal power program annual review: proceedings

    Energy Technology Data Exchange (ETDEWEB)

    None

    1984-03-01

    The primary objective of the Review was to present the results of activities within the Parabolic Dish Technology and Module/Systems Development element of the Department of Energy's Solar Thermal Energy Systems Program. The Review consisted of nine technical sessions covering overall Project and Program aspects, Stirling and Brayton module development, concentrator and engine/receiver development, and associated hardware and test results to date; distributed systems operating experience; international dish development activities; and non-DOE-sponsored domestic dish activities. A panel discussion concerning business views of solar electric generation was held. These Proceedings contain the texts of presentations made at the Review, as submitted by their authors at the beginning of the Review; therefore, they may vary slightly from the actual presentations in the technical sessions.

  4. Regional food dishes in the Brazilian National School Food Program: Acceptability and nutritional composition

    Directory of Open Access Journals (Sweden)

    Diogo thimoteo da Cunha

    2014-08-01

    Full Text Available Objective: the objective of this study was to evaluate the nutritional composition and describe the acceptability of regional culinary dishes served to students from public schools of rural and urban areas. Methods: Ten Brazilian regional dishes were evaluated for acceptability and nutritional composition. the survey was conducted in schools located in rural and urban areas of two cities in the state of São Paulo. Dish acceptability was evaluated using leftover analysis and a 5-point facial hedonic scale. the adherence index was calculated and used as an indirect measure of acceptance, and the nutritional composition was calculated based on the technical files of each dish. Results: A total of 2,384 students from 20 schools participated in the study and 1,174 tasted and evaluated the dishes. the test using the 5-point facial hedonic scale demonstrated that five dishes (Caldo verde soup, persimmon jelly, chicken with okra, puréed cornmeal with spinach, and arugula pizza had an acceptability rate above 85.0%. the mean adherence indices were 57.3% and 55.6% in urban and rural environments, respectively. Analysis of the nutritional composition of regional dishes indicates that these dishes can partially meet macronutrient recommendations. Conclusion: the tested dishes can become part of school menus as they were accepted or partly accepted by the students regardless of school location, whether rural or urban. the cultural heritage is an important resource for the food sovereignty of a country and should be constantly encouraged.

  5. Operational experience and evaluation of a dual-element stretched-membrane heliostat

    Energy Technology Data Exchange (ETDEWEB)

    Strachan, J.W.; Van Der Geest, J.

    1994-01-01

    A dual-element, stretched-membrane central receiver heliostat was designed and manufactured in 1989, by a private US company engaged in the development of commercial central receiver solar technology. The two-module collector, with a collection area of 97.5 m{sup 2}, extends stretched-membrane mirror technology on several fronts with face-down stow capability and a digital controller that integrates tracking and focusing control on a single programmable control board. The solar collector was installed at Sandia`s National Solar Thermal Test Facility in Albuquerque, New Mexico and evaluated over a three-and-a-half year period which ended in September 1993. The measured performance and the operational and maintenance characteristics of this commercial prototype are the subject of this report. The results of beam quality measurements, tracking repeatability tests, measurements of beam movement in elevated winds, performance tests of the focusing system, and all-day beam quality and tracking tests are presented, and the authors offer a detailed discussion of the knowledge gained through operation and maintenance and of the improvements made or suggested to the heliostat`s design.

  6. "He Works Outside the Home; She Drinks Coffee and Does the Dishes" Gender Roles in Fiction Programs on Dutch Television

    NARCIS (Netherlands)

    Emons, P.A.A.; Wester, F.P.J.; Scheepers, P.L.H.

    2010-01-01

    Using a sample of 503 prime-time fiction programs broadcast on Dutch television between 1980 and 2005, the study compared gender portrayals in programs produced in the US with Dutch programs. It revealed more older males, more females involved in childcare, more males in paid employment, and fewer

  7. He works outside the home, she drinks coffee and does the dishes : gender roles in fiction programs on Dutch television

    NARCIS (Netherlands)

    Emons, P.; Wester, F.; Scheepers, P.

    2010-01-01

    Using a sample of 503 prime-time fiction programs broadcast on Dutch television between 1980 and 2005, the study compared gender portrayals in programs produced in the US with Dutch programs. It revealedmore older males, more females involved in childcare, more males in paid employment, and fewer

  8. Single-Dish Radio Polarimetry in the F-GAMMA Program with the Effelsberg 100-m Radio Telescope

    Directory of Open Access Journals (Sweden)

    Beuchert Tobias

    2013-12-01

    Full Text Available Studying the variability of polarized AGN jet emission in the radio band is crucial for understanding the dynamics of moving shocks as well as the structure of the underlying magnetic field. The 100-m Effelsberg Telescope is a high-quality instrument for studying the long-term variability of both total and polarized intensity as well as the electric-vector position angle. Since 2007, the F-GAMMA program has been monitoring the linear polarized emission of roughly 60 blazars at 11 frequencies between 2.7 and 43 GHz. Here, we describe the calibration of the polarimetric data at 5 and 10 GHz and the resulting F-GAMMA full-Stokes light curves for the exemplary case of the radio galaxy 3C 111.

  9. Dish/Stirling for Department of Defense applications final report

    Energy Technology Data Exchange (ETDEWEB)

    Diver, R.B.; Menicucci, D.F. [Sandia National Labs., Albuquerque, NM (United States). Energy and Environment Div.

    1997-03-01

    This report describes a Strategic Environmental Research and Development Program (SERDP) project to field a dish/Stirling system at a southwestern US military facility. This project entitled ``Dish/Stirling for DoD Applications`` was started in August 1993 and was completed in September 1996. The project`s objective was to assist military facilities to field and evaluate emerging environmentally sound and potentially economical dish/Stirling technology. Dish/Stirling technology has the potential to produce electricity at competitive costs while at the same time providing a secure and environmentally benign source of power. In accordance with the SERDP charter, this project leveraged a US Department of Energy (DOE) cost-shared project between Sandia National Laboratories and Cummins Power Generation, Inc. (CPG). CPG is a wholly owned subsidiary of Cummins Engine Company, a leading manufacturer of diesel engines. To accomplish this objective, the project called for the installation of a dish/Stirling system at a military facility to establish first-hand experience in the operation of a dish/Stirling system. To scope the potential DoD market for dish/Stirling technology and to identify the site for the demonstration, a survey of southwestern US military facilities was also conducted. This report describes the project history, the Cummins dish/Stirling system, results from the military market survey, and the field test results.

  10. γ-ray irradiation of cooked dishes

    International Nuclear Information System (INIS)

    Lin Ruotai; Cheng Wei; Wen Shengli; Xiong Guangquan; Ye Lixiu; Chen Yuxia; Zhang Jinmu; He Jianjun; Lin Yong; Zhan Hanping

    2005-01-01

    Ready-to-eat cooked dishes, including stir-fried dishes, steamed dishes, roast meat, deep dried dishes, shrimps and seashells, and dishes of local flavor, etc were irradiated with 60 Co γ-rays, and the decontamination effects were studied. The results showed that most of the cooked dishes are suitable for irradiation. The effective dose is 4 kGy to 8 kGy. Index of microbe of the irradiated dishes was conformed to the National Food-Health standards, and no significant sensory changes was observed with the irradiated dishes. The quality guarantee period (0-5 degree C) is 60 days. (authors)

  11. Dysphagia due to diffuseidiopathic skeletal hyperostosis (DISH ...

    African Journals Online (AJOL)

    Diffuse idiopathic skeletal hyperostosis (DISH) or Forestier's disease isa form of degenerative arthritiswith unique spinal and extra spinal manifestations. Dysphagia due to DISH is uncommon but when present DISH should be suspected. Surgical decompression can relieve some of the symptoms. We report a case of a 60 ...

  12. Solar parabolic dish technology evaluation report

    Science.gov (United States)

    Lucas, J. W.

    1984-01-01

    The activities of the JPL Solar Thermal Power Systems Parabolic Dish Project for FY 1983 are summarized. Included are discussions on designs of module development including concentrator, receiver, and power conversion subsystems together with a separate discussion of field tests, Small Community Experiment system development, and tests at the Parabolic Dish Test Site.

  13. Parabolic dish collectors - A solar option

    Science.gov (United States)

    Truscello, V. C.

    1981-05-01

    A description is given of several parabolic-dish high temperature solar thermal systems currently undergoing performance trials. A single parabolic dish has the potential for generating 20 to 30 kW of electricity with fluid temperatures from 300 to 1650 C. Each dish is a complete power-producing unit, and may function either independently or as part of a group of linked modules. The two dish designs under consideration are of 11 and 12 meter diameters, yielding receiver operating temperatures of 925 and 815 C, respectively. The receiver designs described include (1) an organic working fluid (toluene) Rankine cycle engine; (2) a Brayton open cycle unit incorporating a hybrid combustion chamber and nozzle and a shaft-coupled permanent magnet alternator; and (3) a modified Stirling cycle device originally designed for automotive use. Also considered are thermal buffer energy storage and thermochemical transport and storage.

  14. The Translation of Chinese Dish Names

    Institute of Scientific and Technical Information of China (English)

    龚佳文

    2015-01-01

    The traditional food of a nation reflects its historical and cultural characteristics This thesis begins with an introduction to the translation situation of Chinese dish names and its existing problem nowadays, and proceeds to the translation principles and tactics for English translation of the names of Chinese dishes, based on Eugene A. Nida’ s Functional Equivalence, with an aim to improve translation efficiency and promote cross-cultural communication, and promoting Chinese food culture throughout the globe.

  15. Economic performance of the SCE Stirling dish

    International Nuclear Information System (INIS)

    Stone, K.W.; Lopez, C.W.; McAlister, R.E.

    1993-01-01

    In 1982 McDonnell Douglas Aerospace Space System (MDA-SS) and United Stirling AB of Sweden formed a joint venture to develop and market a solar Stirling dish unit. Eight modules were built and extensively tested from 1984 to 1988. Power production and daily energy-conversion efficiency as determined by field testing have been characterized and modeled in a computer program. Included in this simulation are models of mirror soiling rate, wind spillage loss, mirror washing and other maintenance outage time, operation and maintenance (O and M) costs and other cost models. An economic model of a hybrid (combustion) receiver has been included in the simulation for illustrating the value of using solar energy when available and other fuels such as methane, natural gas, hydrogen, etc. when solar energy is not available or adequate. This paper describes the simulation and presents comparisons of the simulation to test data. The simulation also estimates both the O and M expenses and levelized energy costs for different production volumes

  16. Economic performance of the SCE Stirling dish

    International Nuclear Information System (INIS)

    Stone, K.W.; Lopez, C.W.; McAlister, R.E.

    1995-01-01

    In 1982 McDonnell Douglas Aerospace (MDA) and United Stirling AB (USAB) of Sweden formed a joint venture to develop and market a solar Stirling dish system. Eight modules were built and extensively tested from 1984 to 1988. Power production and daily energy-conversion efficiency as determined by field testing were characterized and modeled into a computer program. Included in this simulation are models of mirror soiling rate, wind spillage loss, mirror washing, and other maintenance outage time, operation and maintenance (O and M) costs, and equipment purchase cost. An economic model of a hybrid (combustion) receiver has been included in the simulation for illustrating the value of using solar energy when available and other fuels such as methane, natural gas, hydrogen, etc. when solar energy is not available or adequate. This paper describes the simulation and presents comparisons of the simulation to test data. The simulation also estimates both the O and M expenses and levelized energy costs for different production volumes

  17. Temperature Performance Evaluation of Parabolic Dishes Covered ...

    African Journals Online (AJOL)

    Aweda

    The parabolic dish with glass material gave the highest temperature of .... 3: Second day variation temperature and time using different materials. 8. 10 .... the sun rays at that particular time. ... especially between 11:00 am and 3:00 pm when.

  18. Temperature Performance Evaluation of Parabolic Dishes Covered ...

    African Journals Online (AJOL)

    Solar radiation reaching the earth is considered to be affected by some parameters like diffusion. This radiation is reflected or scattered by air molecules, cloud and aerosols (dust). Parabolic dishes made of different materials (glass, foil and painted surface) were used to concentrate energy on a copper calorimeter filled with ...

  19. Overview of ESO Large Single Dish Study

    Science.gov (United States)

    Testi, Leonardo

    2018-01-01

    In this talk I will briefly summarize the motivation, methodology and outcome of the ESO Submm Single Dish Strategy WG. The WG was established by the ESO Director for Science and completed its work at the end of 2015. I will summarize the status of the report recommendations, which, among other things, led to the organization of the AtLAST workshop.

  20. Overview of software development at the parabolic dish test site

    Science.gov (United States)

    Miyazono, C. K.

    1985-01-01

    The development history of the data acquisition and data analysis software is discussed. The software development occurred between 1978 and 1984 in support of solar energy module testing at the Jet Propulsion Laboratory's Parabolic Dish Test Site, located within Edwards Test Station. The development went through incremental stages, starting with a simple single-user BASIC set of programs, and progressing to the relative complex multi-user FORTRAN system that was used until the termination of the project. Additional software in support of testing is discussed including software in support of a meteorological subsystem and the Test Bed Concentrator Control Console interface. Conclusions and recommendations for further development are discussed.

  1. Concentrating Solar Power Projects - Dish/Engine Projects | Concentrating

    Science.gov (United States)

    Solar Power | NREL Dish/Engine Projects Photo of several flat, octagonal panels arranged together to form a dish-shaped structure. The receiver is supported above the panels by an arm-like of the panels. These dish/Stirling units are being tested at Sandia National Laboratories in

  2. Solar parabolic dish Stirling engine system design, simulation, and thermal analysis

    International Nuclear Information System (INIS)

    Hafez, A.Z.; Soliman, Ahmed; El-Metwally, K.A.; Ismail, I.M.

    2016-01-01

    into account many factors in the design of the solar dish system. One of these factors is the reflector material of the concentrator and using the results from the Matlab simulation program; where the Polymeric Film, Non Metal reflectors, with a net conversion power of more than 97.07%, still holds the conversion record than the Anod Aluminum reflectors, which has a net conversion power 85.97% with respect to the polished stainless reflectors with a net conversion power 49.52% from the 10 kW Stirling engine. Where the power output differ as 9707, 4952, 8597 W, respectively from the 10 kW Stirling engine. It is shown that there are changes in Stirling power output for different materials, which guide us to select the optimum material, based on the targeted power output and cost. Our target to reach the optimum power that we need it in the design 10 kW power output design as an example from the solar dish Stirling engine.

  3. Corned Beef: an Enigmatic Irish Dish

    OpenAIRE

    Mac Con Iomaire, Máirtín; Gallagher, Pádraic Óg

    2011-01-01

    Corned beef and cabbage, which is consumed in America in large quantities each Saint Patrick’s Day (17th March), is considered by most Americans to be the ultimate Irish dish. However, corned beef and cabbage is seldom eaten in modern day Ireland. It is widely reported that Irish immigrants replaced their beloved bacon and cabbage with corned beef and cabbage when they arrived in America, drawing on the corned beef supplied by their neighbouring Jewish butchers, but not all commentators beli...

  4. Theoretical modelling of solar dish concentrator

    International Nuclear Information System (INIS)

    Yaaseen Rafeeu; Mohd Zainal Abidin Abdul Kadir; Senan Mohamed Abdulla; Nor Mariah Adam

    2009-01-01

    Full text: Concentrating solar power (CSP) technologies could be one of the major contributor to worlds future energy needs and which would be cheap and clean sources of energy. This would improve energy utilization, higher conversion efficiency with reliable and affordable supply of electricity to the public. The proposed approach is using different size and depth of solar dish concentrators to improve solar fraction using the aluminium foil as reflector. In this paper, different measurement of solar concentrators is investigated and aims to aims to introducing an improved methodology for solar fraction on incoming solar energy in wet climate. (author)

  5. An Automatic High Efficient Method for Dish Concentrator Alignment

    Directory of Open Access Journals (Sweden)

    Yong Wang

    2014-01-01

    for the alignment of faceted solar dish concentrator. The isosceles triangle configuration of facet’s footholds determines a fixed relation between light spot displacements and foothold movements, which allows an automatic determination of the amount of adjustments. Tests on a 25 kW Stirling Energy System dish concentrator verify the feasibility, accuracy, and efficiency of our method.

  6. A parametric investigation on a solar dish-Stirling system

    Science.gov (United States)

    Gholamalizadeh, Ehsan; Chung, Jae Dong

    2018-06-01

    The aim of this study is to analyze the performance of a solar dish-Stirling system. A mathematical model for the overall thermal efficiency of the solar-powered high-temperature-differential dish-Stirling engine is described. This model takes into account pressure losses due to fluid friction which is internal to the engine, mechanical friction between the moving parts, actual heat transfer includes the effects of both internal and external irreversibilities of the cycle and finite regeneration processes time. Validation was done through comparison with the actual power output of the "EuroDish" system. Moreover, the effects of dish diameter and working fluid on the performance of the system were studied. An increase of about 7.2% was observed for the power output using hydrogen as the working fluid rather than helium. Also, the focal distance for any diameter of dish was calculated.

  7. Stretched membrane heliostats: design and structural analysis of reflectance module and support of a heliostats of 9 m. diaform and 60 m''3 of reflectance surface

    International Nuclear Information System (INIS)

    Figarola Torres, J. M.

    1993-01-01

    After having designed and built at CIEMAT a first prototype of a Btretched membrane heliostats of 3 m. diameter, the design and the structural analysis of the different components included in the reflectance module and support of another heliostats, this one of 9 m. diameter and 60 m2. of reflectance surface, are shown In this report. This last heliostats will be mounted on a pedestal and its driving device at the Solar Platform of Almeria. In order to optimize design and performance, the structural analysis of its basic components has been analyzed with the finite elements program ANSYS. The following elements have been subject to analysis: the membrane and their ring supports, stretching system and the structural support. A similar scheme to the one applied to the previous prototype has been used on the focus control system. That includes a linear transducer, a variable frequency and a fan. Finally it has to be pointed out that substantial improvements have been achieved with respect to the first prototype concerning design and cost. (Author) 5 refs

  8. Hygienic status assessment of dish washing waters, utensils, hands ...

    African Journals Online (AJOL)

    Hygienic status assessment of dish washing waters, utensils, hands and pieces of money from street food processing sites in Ouagadougou (Burkina Faso). N Barro, AR Bello, A Savadogo, CAT Ouattara, AJ Iiboudo, AS Traoré ...

  9. Mechanical design of a low cost parabolic solar dish concentrator

    Directory of Open Access Journals (Sweden)

    Hamza Hijazi

    2016-03-01

    Full Text Available The objective of this research was to design a low cost parabolic solar dish concentrator with small-to moderate size for direct electricity generation. Such model can be installed in rural areas which are not connected to governmental grid. Three diameters of the dish; 5, 10 and 20 m are investigated and the focal point to dish diameter ratio is set to be 0.3 in all studied cases. Special attention is given to the selection of the appropriate dimensions of the reflecting surfaces to be cut from the available sheets in the market aiming to reduce both cutting cost and sheets cost. The dimensions of the ribs and rings which support the reflecting surface are optimized in order to minimize the entire weight of the dish while providing the minimum possible total deflection and stresses in the beams. The study applies full stress analysis of the frame of the dish using Autodesk Inventor. The study recommends to use landscape orientation for the reflective facets and increase the ribs angle and the distance between the connecting rings. The methodology presented is robust and can be extended to larger dish diameters.

  10. Summary assessment of solar thermal parabolic dish technology for electrical power generation

    Science.gov (United States)

    Penda, P. L.; Fujita, T.; Lucas, J. W.

    1985-01-01

    An assessment is provided of solar thermal parabolic dish technology for electrical power generation. The assessment is based on the development program undertaken by the Jet Propulsion Laboratory for the U.S. Department of Energy and covers the period from the initiation of the program in 1976 through mid-1984. The program was founded on developing components and subsystems that are integrated into parabolic dish power modules for test and evaluation. The status of the project is summarized in terms of results obtained through testing of modules, and the implications of these findings are assessed in terms of techno-economic projections and market potential. The techno-economic projections are based on continuation of an evolutionary technological development program and are related to the accomplishments of the program as of mid-1984. The accomplishments of the development effort are summarized for each major subsystem including concentrators, receivers, and engines. The ramifications of these accomplishments are assessed in the context of developmental objectives and strategies.

  11. Transfer of fibroblast sheets cultured on thermoresponsive dishes with membranes.

    Science.gov (United States)

    Kawecki, Marek; Kraut, Małgorzata; Klama-Baryła, Agnieszka; Łabuś, Wojciech; Kitala, Diana; Nowak, Mariusz; Glik, Justyna; Sieroń, Aleksander L; Utrata-Wesołek, Alicja; Trzebicka, Barbara; Dworak, Andrzej; Szweda, Dawid

    2016-06-01

    In cell or tissue engineering, it is essential to develop a support for cell-to-cell adhesion, which leads to the generation of cell sheets connected by extracellular matrix. Such supports must be hydrophobic and should result in a detachable cell sheet. A thermoresponsive support that enables the cultured cell sheet to detach using only a change in temperature could be an interesting alternative in regenerative medicine. The aim of this study was to evaluate plates covered with thermoresponsive polymers as supports for the formation of fibroblast sheets and to develop a damage-free procedure for cell sheet transfer with the use of membranes as transfer tools. Human skin fibroblasts were seeded on supports coated with a thermoresponsive polymer: commercial UpCell™ dishes (NUNC™) coated with thermoresponsive poly(N-isopropylacrylamide) (PNIPAM) and dishes coated with thermoresponsive poly(tri(ethylene glycol) monoethyl ether methacrylate) (P(TEGMA-EE)). Confluent fibroblast sheets were effectively cultured and harvested from both commercial PNIPAM-coated dishes and laboratory P(TEGMA-EE)-coated dishes. To transfer a detached cell sheet, two membranes, Immobilon-P(®) and SUPRATHEL(®), were examined. The use of SUPRATHEL for relocating the cell sheets opens a new possibility for the clinical treatment of wounds. This study established the background for implementing thermoresponsive supports for transplanting in vitro cultured fibroblasts.

  12. Radiotreatment of dishes cooked : Royal cutlets of chickens

    International Nuclear Information System (INIS)

    Bousselmi, Mehrez

    2006-01-01

    The cooked dishes often present themselves as the complex products of microbiological, biochemival view point and organoleptic.However, the demand of the local and international market stops showing a tendency toward use increased of these cooked dishes of which problems to get round are very delicate. The ionization can be an alternative of conservation since it is characterized bye one fashion of action fundamentally different of the classic techniques: it is about exposing during a determined length, of the wrapped food commodities or in a jumble to doses of ionising radiance carefully controlled in order to get the sought-after effect. The irradiation showed a big efficiency therefore on the plan microbiology.Indeed the dose 1 KGy destroyed all present microorganisms in dishes cooked pasteurized. whereas, for dishes cooked non pasteurized, a dose of 2 KGy destroyed completely the flora of contamination. Besides, the irradiation entails a light reduction of the biochemical composition, while keeping qualities intact organoleptic for all analyzed samples. As a conclusion, the irradiation increases the length of conservation, what confirms the reliability of such a process, in addition of his/her/its weak energizing cost. (author)

  13. Ankylosant spondylitis association and diffuse idiopathic skeletal hyperostosis (DISH)

    International Nuclear Information System (INIS)

    Medina, Yimi; Restrepo Suarez, Jose Felix; Calvo Paramo, Enrique

    2000-01-01

    We are presenting a 66 year-old patient complaining of low back pain for the last 3 months and cervical pain for the last 45 days, Review of systems showed long standing lumbar and cervical stiffness, Radiological studies were compatible with ankylosing spondylitis and DISH (Diffuse idiopathic Skeletal Hyperostosis). Associations of those diseases are uncommon and reported only few times in the literature

  14. Dish concentrators for solar thermal energy - Status and technology development

    Science.gov (United States)

    Jaffe, L. D.

    1981-01-01

    Comparisons are presented of point-focusing, or 'dish' solar concentrator system features, development status, and performance levels demonstrated to date. In addition to the requirements of good optical efficiency and high geometric concentration ratios, the most important future consideration in solar thermal energy dish concentrator design will be the reduction of installed and lifetime costs, as well as the materials and labor costs of production. It is determined that technology development initiatives are needed in such areas as optical materials, design wind speeds and wind loads, structural configuration and materials resistance to prolonged exposure, and the maintenance of optical surfaces. The testing of complete concentrator systems, with energy-converting receivers and controls, is also necessary. Both reflector and Fresnel lens concentrator systems are considered.

  15. Development status of the PDC-1 Parabolic Dish Concentrator

    Science.gov (United States)

    Thostesen, T.; Soczak, I. F.; Pons, R. L.

    1982-01-01

    The status of development of the 12 m diameter parabolic dish concentrator which is planned for use with the Small Community Solar Thermal Power System. The PDC-1 unit features the use of plastic reflector film bonded to structural plastic gores supported by front-bracing steel ribs. An elevation-over-azimuth mount arrangement is employed, with a conventional wheel-and-track arrangement; outboard trunnions permit the dish to be stored in the face down position, with the added advantage of easy access to the power conversion assembly. The control system is comprised of a central computer (LSI 1123), a manual control panel, a concentrator control unit, two motor controllers, a Sun sensor, and two angular position resolvers. The system is designed for the simultaneous control of several concentrators. The optical testing of reflective panels is described.

  16. FPGA applications for single dish activity at Medicina radio telescopes

    Science.gov (United States)

    Bartolini, M.; Naldi, G.; Mattana, A.; Maccaferri, A.; De Biaggi, M.

    FPGA technologies are gaining major attention in the recent years in the field of radio astronomy. At Medicina radio telescopes, FPGAs have been used in the last ten years for a number of purposes and in this article we will take into exam the applications developed and installed for the Medicina Single Dish 32m Antenna: these range from high performance digital signal processing to instrument control developed on top of smaller FPGAs.

  17. Searching for WISPy cold dark matter with a dish antenna

    Energy Technology Data Exchange (ETDEWEB)

    Horns, Dieter [Hamburg Univ. (Germany). Inst. fuer Experimentalphysik; Jaeckel, Joerg [Heidelberg Univ. (Germany). Inst. fuer Theoretische Physik; Durham Univ. (United Kingdom). Inst. for Particle Physics Phenomenology; Lindner, Axel; Ringwald, Andreas [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Lobanov, Andrei [Max-Planck-Institut fuer Radioastronomie, Bonn (Germany); Redondo, Javier [Muenchen Univ. (Germany). Arnold Sommerfeld Center; Max-Planck-Institut fuer Physik, Muenchen (Germany)

    2012-12-15

    The cold dark matter of the Universe may be comprised of very light and very weakly interacting particles, so-called WISPs. Two prominent examples are hidden photons and axion-like particles. In this note we propose a new technique to sensitively search for this type of dark matter with dish antennas. The technique is broadband and allows to explore a whole range of masses in a single measurement.

  18. White Paper on Dish Stirling Technology: Path Toward Commercial Deployment

    Energy Technology Data Exchange (ETDEWEB)

    Andraka, Charles E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Concentrating Solar Power Dept.; Stechel, Ellen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Concentrating Solar Power Dept.; Becker, Peter [Stirling Energy Systems, Scottsdale, AZ (United States); Messick, Brian [Stirling Energy Systems, Scottsdale, AZ (United States)

    2016-07-01

    Dish Stirling energy systems have been developed for distributed and large-scale utility deployment. This report summarizes the state of the technology in a joint project between Stirling Energy Systems, Sandia National Laboratories, and the Department of Energy in 2011. It then lays out a feasible path to large scale deployment, including development needs and anticipated cost reduction paths that will make a viable deployment product.

  19. Overview of Submm Single Dish: From Observations to Useful Data

    Science.gov (United States)

    Stanke, Thomas

    2018-03-01

    Observing with single dish telescopes at submillimetre wavelengths adds a number of challenges. The Earth's atmosphere not only absorbs the sky signal with varying amounts as a function of frequency and weather conditions, but it also emits a signal that is many orders of magnitude brighter than the astronomical signal one is interested in. Additional challenges come in the calibration and removal of certain instrumental effects. I will give an overview of present and planned submillimetre telescopes, instrument types, and observing strategies.

  20. Artificial neural networks approach on solar parabolic dish cooker

    International Nuclear Information System (INIS)

    Lokeswaran, S.; Eswaramoorthy, M.

    2011-01-01

    This paper presents heat transfer analysis of solar parabolic dish cooker using Artificial Neural Network (ANN). The objective of this study to envisage thermal performance parameters such as receiver plate and pot water temperatures of the solar parabolic dish cooker by using the ANN for experimental data. An experiment is conducted under two cases (1) cooker with plain receiver and (2) cooker with porous receiver. The Back Propagation (BP) algorithm is used to train and test networks and ANN predictions are compared with experimental results. Different network configurations are studied by the aid of searching a relatively better network for prediction. The results showed a good regression analysis with the correlation coefficients in the range of 0.9968-0.9992 and mean relative errors (MREs) in the range of 1.2586-4.0346% for the test data set. Thus ANN model can successfully be used for the prediction of the thermal performance parameters of parabolic dish cooker with reasonable degree of accuracy. (authors)

  1. Numerical and experimental dosimetry of petri dish exposure setups

    Energy Technology Data Exchange (ETDEWEB)

    Burkhardt, M.; Pokovic, K.; Gnos, M.; Schmid, T.; Kuster, N. [Swiss Federal Inst. of Tech., Zurich (Switzerland)

    1996-12-31

    Crawford TEM cells are often used to exposure cell cultures or small animals in order to study the effects caused by high-frequency fields. They are self-contained, easy-to-use setups that provide a rather homogeneous field distribution in a large area around its center, corresponding approximately to far-field conditions. However, a number of conditions must be met if such TEM cells are intended to be used for in vitro experiments. For instance, poor interaction with the incident field must be maintained to avoid significant field disturbances in the TEM cell. This is best achieved with E-polarization, i.e., when the E-field vector is normal to the investigated cell layer lining the bottom of a synthetic Petri dish. In addition, E-polarization provides the most homogeneous field distribution of all polarizations within the entire layer of cells. In this paper, the authors present a detailed dosimetric assessment for 60 and 100 mm Petri dishes as well as for a 48-well titer plate at 835 MHz. The dosimetry was performed by using numerical computations. The modeling and the simplifications are validated by a second numerical technique and by experimental measurements. For thin liquid layers, an approximation formula is provided with which the induced field strength for many other experiments conducted in Petri dishes can be assessed reliably.

  2. Feasibility study of dish/stirling power systems in Turkey

    Science.gov (United States)

    Zilanlı, Gülin Acarol; Eray, Aynur

    2017-06-01

    In this study, two different commercial dish/stirling systems, SES (Stirling Energy Systems) and WGA-ADDS (WGAssociates - Advanced Dish Development System), are modeled using the "System Advisor Model" (SAM) modeling software in designated settlement areas. Both systems are modeled for the US state of Albuquerque, where they were designed, and Turkish provinces of Ankara, Van, Muğla, Mersin, Urfa and Konya. At first, the dish/stirling system is optimized according to the power output values and the system loss parameters. Then, the layout of the solar field is designed with an installed capacity of 600kW both of SES and WGA-ADDS systems, Upon securing the most suitable layout, the system is modeled for the aforementioned settlements using the optimum output values gathered from the parametric analysis. As a result of the simulation studies, the applicability of this model is discussed according to the power output and the efficiency. Although Turkey is located in an area called "the sun belt" where solar energy technologies can be used, there is no advanced application of these systems. This study aims to discuss the application of these systems in detail and to pave the way for future studies in this field.

  3. Ideas for future large single dish radio telescopes

    Science.gov (United States)

    Kärcher, Hans J.; Baars, Jacob W. M.

    2014-07-01

    The existing large single dish radio telescopes of the 100m class (Effelsberg, Green Bank) were built in the 1970s and 1990s. With some active optics they work now down to 3 millimeter wavelength where the atmospheric quality of the site is also a limiting factor. Other smaller single dish telescopes (50m LMT Mexico, 30m IRAM Spain) are located higher and reach sub-millimeter quality, and the much smaller 12m antennas of the ALMA array reach at a very high site the Terahertz region. They use advanced technologies as carbon fiber structures and flexible body control. We review natural limits to telescope design and use the examples of a number of telescopes for an overview of the available state-of-the-art in design, engineering and technologies. Without considering the scientific justification we then offer suggestions to realize ultimate performance of huge single dish telescopes (up to 160m). We provide an outlook on design options, technological frontiers and cost estimates.

  4. Sparking interest in restaurant dishes? Cognitive and affective processes underlying dish design and ecological origin. An fMRI study.

    Science.gov (United States)

    Muñoz-Leiva, Francisco; Gómez-Carmona, Diego

    2018-06-14

    The objective of the current paper is to verify to what extent the presentation of a restaurant dish and the origin of its food provoke reactions in the consumer's brain during the visualization and the decision-making process, from an exploratory approach. The two independent variables singled out for study were whether the presentation was well or poorly presented and if the ingredients were ecological or non-ecological. The results applying the functional magnetic resonance image (fMRI) methodology reveal that well-presented dishes activate areas in the brain linked to the network of emotions indicating that the visualization in restaurant menus is not a purely cognitive and self-reflexive process but retains a strong affective component. Furthermore, the presence of this component is kept at the moment of choosing a dish, as observed by the activation of the gyrus cingulate, region linked to the regulatory processes of emotions. Hence, research ratifies the existence of an emotional factor during the entire process of decision-making carried out in a restaurant. Yet it is true that exposure to an ecological menu provokes activation of the medial frontal cortex, a region connected to higher reasoning and attention, suggesting that stimuli from well-presented dishes of ecological origin trigger neuronal responses related to high-level cognitive processes. The practical implications derived, along with its limitations and the future research opportunities, are interesting for both developing theory and also practice. Therefore, scholars are encouraged to further test some research proposals (e.g. moderating role of salubrity or simultaneously eye tracking method). Copyright © 2017. Published by Elsevier Inc.

  5. Modification of parabolic dish antenna pattern using two symmetrically placed circular flat plates

    Science.gov (United States)

    Thorpe, Glen C.

    1987-12-01

    This study aims to formulate a method of predicting the far field pattern of a parabolic dish antenna with two moveable flat plates mounted symmetrically on either side of the feed horn. The approach taken has been to first analyze the radiation pattern of the antenna with the disks at certain heights out from the surface of the dish. To do this the near-field radiation in amplitude and phase was measured over a plane surface in the near-field and the values were then transformed into the far field using a Fast Fourier Transform. Far field pattern values of the antenna were directly measured for each setting of the plates. The results obtained from the Fast Fourier Transform of the near field data were in good agreement with the values obtained by measurement. Finally, an approximate model of the antenna was developed and implemented as a computer program. This model, while relatively unsophisticated, provided some insights into the changes in the near field phase distribution caused by the moveable circular flat plates.

  6. Design of the support structure, drive pedestal, and controls for a solar concentrator

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, V.R.; Ford, J.L.; Anderson, A.E. (WG Associates, Dallas, TX (United States))

    1991-08-01

    The glass/metal McDonnell-Douglas dish is the state-of-the-art of parabolic dish concentrators. Because of the perceived high production cost of this concentrator, the Department of Energy's Solar Thermal Program is developing stretch-membrane technology for large (75 kWt) solar concentrators for integration with receivers and engines in 25 kWe dish-Stirling systems. The objective of this development effort is to reduce the cost of the concentrator while maintaining the high levels of performance characteristic of glass-metal dishes. Under contract to Sandia National Laboratories, Science Applications International Corporation, Solar Kinetics Inc. and WG Associates are developing a faceted stretched-membrane heliostat technology. This design will result in a low-risk, near-term concentrator for dish-Stirling systems. WG Associates has designed the support structure, drives and tracking controls for this dish. The structure is configured to support 12 stretched-membrane, 3.5-meter diameter facets in a shaped dish configuration. The dish design is sized to power a dish-Stirling system capable of producing 25 kW (electric). In the design of the structure, trade-off studies were conducted to determine the best'' facet arrangement, dish contour, dish focal length, tracking control and walk-off protection. As part of the design, in-depth analyses were performed to evaluate pointing accuracy, compliance with AISC steel design codes, and the economics of fabrication and installation. Detailed fabrication and installation drawings were produced, and initial production cost estimates for the dish were developed. These issues, and the final dish design, are presented in this report. 7 refs., 33 figs., 18 tabs.

  7. Spondyloarthritis, diffuse idiopathic skeletal hyperostosis (DISH) and chondrocalcinosis.

    Science.gov (United States)

    Armas, Jácome Brugues; Couto, Ana Rita; Bettencourt, Bruno Filipe

    2009-01-01

    The authors describe the main clinical and radiological findings of common enthesopathic disorders-spondylarthritis (SpA), chondrocalcinosis/calcium pyrophosphate dehydrate crystal deposition disease (CPPD CDD) and diffuse idiopathic skeletal hyperostosis (DISH), stressing similarities and differences which may help in the differential diagnosis. They emphasize the clinical presentation of the "pseudoankylosing spondylitis" forms of CPPD CDD. They also review the most relevant genes and molecular mechanisms associated with these conditions and with another enthesopathic disorder with high prevalence in the Japanese population-ossification of the posterior longitudinal ligament (OPLL).

  8. Gods, Germs, and Petri Dishes: Toward a Nonsecular Medical Anthropology.

    Science.gov (United States)

    Roberts, Elizabeth F S

    2016-01-01

    This commentary calls on medical anthropology to become programmatically non-secular. Despite recent anthropological critiques of secularity, within and outside of anthropology, most contemporary medical anthropologists continue to leave deities and religiosity out of their examinations of healing practices, especially in their accounts of biomedicine. Through a critical, relational constructionist lens, which traces how all entities are both constructed and real, a non-secular medical anthropology would insist that when deities are part of medical practice, they are integral to analysis. Importantly then, within the symmetrical nature of this same constructionist lens, biomedical entities like germs and petri dishes need to be accounted for just as much as deities.

  9. Experimental studies on solar parabolic dish cooker with porous medium

    International Nuclear Information System (INIS)

    Lokeswaran, S.; Eswaramoorthy, M.

    2012-01-01

    The solar cooking is the alternate method of cooking to reduce consumptions of fossil fuels. An affordable, energy efficient solar cooking technology is much need due to the fossil fuels increasing cost and it is the hottest research topic in all over the world. This paper presents an experimental analysis of the heat transfer enhancement of solar parabolic dish cookers by a porous medium made of scrap material. Using the stagnation temperature test and water boiling test are conducted on the cooking vessel with and without porous medium. Experimental results are compared for both cases in terms of thermal performance, optical efficiency, heat loss factor and cooking power. (authors)

  10. Recent developments: PKI square dish for the Soleras Project

    Science.gov (United States)

    Rogers, W. E.

    1984-03-01

    The Square Dish solar collectors are subjected to rigorous design attention regarding corrosion at the site, and certification of the collector structure. The microprocessor controls and tracking mechanisms are improved in the areas of fail safe operations, durability, and low parasitic power requirements. Prototype testing demonstrates performance efficiency of approximately 72% at 730 F outlet temperature. Studies are conducted that include developing formal engineering design studies, developing formal engineering design drawing and fabrication details, establishing subcontracts for fabrication of major components, and developing a rigorous quality control system. The improved design is more cost effective to product and the extensive manuals developed for assembly and operation/maintenance result in faster field assembly and ease of operation.

  11. Thermal Model of a Dish Stirling Cavity-Receiver

    Directory of Open Access Journals (Sweden)

    Rubén Gil

    2015-01-01

    Full Text Available This paper presents a thermal model for a dish Stirling cavity based on the finite differences method. This model is a theoretical tool to optimize the cavity in terms of thermal efficiency. One of the main outcomes of this work is the evaluation of radiative exchange using the radiosity method; for that purpose, the view factors of all surfaces involved have been accurately calculated. Moreover, this model enables the variation of the cavity and receiver dimensions and the materials to determine the optimal cavity design. The tool has been used to study the cavity optimization regarding geometry parameters and material properties. Receiver absorptivity has been identified as the most influential property of the materials. The optimal aperture height depends on the minimum focal space.

  12. Advancing food, nutrition, and health research in Europe by connecting and building research infrastructures in a DISH-RI: Results of the EuroDISH project

    DEFF Research Database (Denmark)

    Snoek, Harriëtte M.; Eijssen, Lars M.T.; Geurts, Marjolein

    2018-01-01

    more effectively. Approach In the EuroDISH project we mapped existing RIs in the food and health area in Europe, identified outstanding needs, and synthesised this into a conceptual design of a pan-European DISH-RI. The DISH model was used to describe and structure the research area: Determinants...... of food choice, Intake of foods and nutrients, Status and functional markers of nutritional health, and Health and disease risk. Key findings The need to develop RIs in the food and health domain clearly emerged from the EuroDISH project. It showed the necessity for a unique interdisciplinary and multi......Background Research infrastructures (RIs) are essential to advance research on the relationship between food, nutrition, and health. RIs will facilitate innovation and allow insights at the systems level which are required to design (public health) strategies that will address societal challenges...

  13. Healthier side dishes at restaurants: an analysis of children's perspectives, menu content, and energy impacts.

    Science.gov (United States)

    Anzman-Frasca, Stephanie; Dawes, Franciel; Sliwa, Sarah; Dolan, Peter R; Nelson, Miriam E; Washburn, Kyle; Economos, Christina D

    2014-07-04

    Children consume restaurant-prepared foods at high rates, suggesting that interventions and policies targeting consumption of these foods have the potential to improve diet quality and attenuate excess energy intake. One approach to encouraging healthier dietary intake in restaurants is to offer fruits and vegetables (FV) as side dishes, as opposed to traditional, energy-dense accompaniments like French fries. The aims of the current study were to examine: children's views about healthier side dishes at restaurants; current side dish offerings on children's menus at leading restaurants; and potential energy reductions when substituting FV side dishes in place of French fries. To investigate children's attitudes, a survey was administered to a nationally representative sample of U.S. 8- to 18-year-olds (n = 1178). To examine current side dish offerings, children's menus from leading quick service (QSR; n = 10) and full service restaurant chains (FSR; n = 10) were analyzed. Energy reductions that could result from substituting commonly-offered FV side dishes for French fries were estimated using nutrition information corresponding to the children's menu items. Two-thirds of children reported that they would not feel negatively about receiving FV sides instead of French fries with kids' meals. Liking/taste was the most common reason that children gave to explain their attitudes about FV side dishes. Nearly all restaurants offered at least 1 FV side dish option, but at most restaurants (60% of QSR; 70% of FSR), FV sides were never served by default. Substituting FV side dishes for French fries yielded an average estimated energy reduction of at least 170 calories. Results highlight some healthy trends in the restaurant context, including the majority of children reporting non-negative attitudes about FV side dishes and the consistent availability of FV side dish options at leading QSR and FSR. Yet the minority of restaurants offer these FV sides by default

  14. Dish-based CPV-T for rooftop generation

    Science.gov (United States)

    Davila-Peralta, Christian; Hyatt, Justin; Alfred, Dan; Struble, Morgan; Sodari, Frank; Angel, Roger

    2017-09-01

    Hybrid CPV-T with combined electrical and thermal output is well suited to solar generation from fixed limited areas, such as on the roof of an industrial or commercial facility with need for heat. This application will become especially attractive once overall electrical conversion efficiency of 40% is reached, as is projected for REhnu CPV systems using multijunction cells of 50% efficiency, anticipated in a few years. We outline here a configuration of dish- based CPV trackers optimized for close packing on a flat roof in a triangular grid, with a mirror area-to-ground area ratio of 50%. When the geometry of shadowing averaged over a year is taken into account, 80% of all the sunlight that would strike the rooftop is directed into the receivers. Such an array on a given area of flat roof will generate more electrical energy than would be possible with conventional PV panels, even if covering the entire rooftop, because of silicon's relative inefficiency. For example, in Tucson, the annual average global flux of 5.7 kWh/m2/day on a horizontal surface covered with 22% silicon modules will yield 1.25 kWh/m2/day. We show that a CPV system collecting 80% of all the direct sunlight of 7.0 kWh/m2 and converting it with 40% efficiency will yield 2.24 kWh/m2/day of rooftop area, nearly twice as much4. Thermal power will double again the total energy yield. A dual axis CPV-T tracker designed specifically very close spacing has been built to carry a single dish mirror of the standard type used in REhnu's M-8 generator, described by Stalcup et al in these proceedings1,2. Sunlight is collected and focused by a single square paraboloidal mirror, 1.65 × 1.65 m with focal length of 1.5 m. For closest possible packing without mechanical interference, and for broad distribution of load on a rooftop, the mirror and receiver are mounted to a C-ring structure, configured such that the elevation and azimuth axes intersect at a virtual pivot, at the center of the sphere that just

  15. [Sodium, potassium and calcium content in regional dishes consumed in Sonora, Mexico].

    Science.gov (United States)

    Grijalva Haro, M I; Valencia, M E; Wyatt, J

    1990-06-01

    The content of sodium, potassium and calcium was determined in 15 regional dishes, by atomic absorption spectrophotometry. The Na:K ratio was high in most of the dishes due to the high sodium content and low content of potassium found. The higher sources of the studied minerals were "tortilla de harina" with 1,372.8 mg/100 g of sodium; "chorizo con papas" with 466 mg/100 g of potassium, and "calabacitas con queso" with 244.1 mg/100 g of calcium. Two of the dishes considered as desserts, "capirotada" and "arroz con leche" showed the lowest Na:K ratio (0.66 and 0.81, respectively).

  16. Test results on parabolic dish concentrators for solar thermal power systems

    Science.gov (United States)

    Jaffe, Leonard D.

    1989-01-01

    This paper presents results of development testing of various solar thermal parabolic dish concentrators. The concentrators were mostly designed for the production of electric power using dish-mounted Rankine, Brayton or Stirling cycle engines, intended to be produced at low cost. Measured performance for various dishes included optical efficiencies ranging from 0.32 to 0.86 at a geometric concentration ratio of 500, and from about 0.09 to 0.85 at a geometric concentration ratio of 3000. Some malfunctions were observed. The tests should provide operating information of value in developing concentrators with improved performance and reduced maintenance.

  17. Chefs move to schools. A pilot examination of how chef-created dishes can increase school lunch participation and fruit and vegetable intake.

    Science.gov (United States)

    Just, David R; Wansink, Brian; Hanks, Andrew S

    2014-12-01

    To demonstrate the feasibility of introducing a main dish designed by a professional chef in the National School Lunch Program and to document the impact on child participation, a chef was recruited to design pizza to be served in an upstate New York school district. The pizza was designed to meet both the cost and ingredient requirements of the NSLP. High school students were significantly more likely to select the pizza prepared by the chef. While the chef had no significant impact on main dish consumption given selection, more students took a vegetable and vegetable consumption increased by 16.5%. This pilot study demonstrates the plausibility of using chefs to boost participation in the school lunch program, and potentially increase nutrition through side selection, among high school students. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. A review of test results on parabolic dish solar thermal power modules with dish-mounted Rankine engines and for production of process steam

    Science.gov (United States)

    Jaffe, Leonard D.

    1988-11-01

    This paper presents results of development testing of various solar thermal parabolic dish modules and assemblies. Most of the tests were at modules and assemblies that used a dish-mounted, organic Rankine cycle turbine for production of electric power. Some tests were also run on equipment for production of process steam or for production of electricity using dish-mounted reciprocating steam engines. These tests indicate that early modules achieve efficiencies of about 18 percent in converting sunlight to electricity (excluding the inverter but including parasitics). A number of malfunctions occurred. The performance measurements, as well as the malfunctions and other operating experience, provided information that should be of value in developing systems with improved performance and reduced maintenance.

  19. Nutritional composition of the commonly consumed composite dishes for the Barbados National Cancer Study.

    Science.gov (United States)

    Sharma, Sangita; Harris, Rachel; Cao, Xia; Hennis, Anselm J M; Leske, M Cristina; Wu, Suh-Yuh

    2007-09-01

    To provide, for the first time, the calculated nutritional composition of 32 composite dishes commonly consumed in Barbados to enable dietary intake to be calculated from a Quantitative Food Frequency Questionnaire developed specifically for this population to determine associations between diet and risk of prostate and breast cancer. Weighed recipes were collected in up to six different households for each of the 32 composite dishes. The average nutritional composition for these composite dishes was calculated using the US Department of Agriculture National Nutrient Database. One hundred and fifty-two weighed recipes were collected for 32 composite dishes: five were fish based, two were ground beef dishes, two were chicken based, two were offal based, two were lamb dishes, one was pork based, three were rice based, three were commonly consumed home-made drinks, and the remaining were miscellaneous items. A total of 152 weighed recipes were collected and we provide, for the first time, nutritional composition data for 32 commonly consumed food and drink items in Barbados. Such data are essential for assessing nutrient intake and determining associations between diet and prostate and breast cancer in the Barbados National Cancer Study.

  20. Efficient, Low Cost Dish Concentrator for a CPV Based Cogeneration System

    Science.gov (United States)

    Chayet, Haim; Kost, Ori; Moran, Rani; Lozovsky, Ilan

    2011-12-01

    Zenith Solar Ltd has developed efficient electricity and heat co-generation system based on segmented-parabolic dish of total aperture area of 11 m2 and water cooled dense array module combined of triple junction cells. Conventional parabolic dishes are inherently inefficient in the sense that the radiant flux distribution is non uniform causing inefficient generation by the PV array. Secondary optics improves uniformity but introduces additional complexity and losses to the system. Zenith's dish is assembled of 1200 flat mirrors of approximately 100 cm2 each. Every mirror facet has a unique shape such that the geometrical projection from each mirror on the focal plane is essentially the same. When perfectly aligned, the projected radiation from all mirrors overlaps uniformly on the PV surface. The low cost construction of the dish utilizes plastic mount supported by a precise metal frame. The precision of the metal frame affects the overall optical efficiency of the mirror and hence the efficiency of the system. State of the art dish of 11 m2 active aperture results in output of 2.25 kWp (900 W/m2) electrical and 5 kWp thermal power from one dish system representing 21% electrical and 50% thermal conversion efficiency adding to 71% overall system efficiency.

  1. Software used with the flux mapper at the solar parabolic dish test site

    Science.gov (United States)

    Miyazono, C.

    1984-01-01

    Software for data archiving and data display was developed for use on a Digital Equipment Corporation (DEC) PDP-11/34A minicomputer for use with the JPL-designed flux mapper. The flux mapper is a two-dimensional, high radiant energy scanning device designed to measure radiant flux energies expected at the focal point of solar parabolic dish concentrators. Interfacing to the DEC equipment was accomplished by standard RS-232C serial lines. The design of the software was dicated by design constraints of the flux-mapper controller. Early attemps at data acquisition from the flux-mapper controller were not without difficulty. Time and personnel limitations result in an alternative method of data recording at the test site with subsequent analysis accomplished at a data evaluation location at some later time. Software for plotting was also written to better visualize the flux patterns. Recommendations for future alternative development are discussed. A listing of the programs used in the anaysis is included in an appendix.

  2. On the evolution, over four generations of paraboloidal dish solar thermal electric power systems

    International Nuclear Information System (INIS)

    Kaneff, S.

    1993-01-01

    After a decade of supplying useful power, the White Cliffs Paraboloidal Dish Solar Thermal Power Station (1100 km west of Sydney) is still operational and has provided major lessons and experience for subsequent developments; particularly for the Molokai/Alburquerque unit built jointly with Power Kinetics Inc (of Troy, USA) for the US Department of Energy. This has, in turn, given valuable guidance for the third generation system now nearing completion in Canberra and employing new collector concepts refined for commercial production and viability. Unlike much dish-oriented R and D, we consider systems of dish arrays supplying central plant as a more attractive proposition than assemblies of dish/engine units, for all but very small systems (<2 MWe). Development has recently commerce on the fourth generation technology which result in a 2 MWe dish system within 2 years, expected to be followed closely by a system of 10 to 20 MWe, preparatory to still larger systems, as the technology evolves and experience is gained. The rationale in this progression in based on the achievement of commercial cost-effectiveness in competition with other energy sources. The direction of evolution is becoming clear and application of the technology to broader spheres than electricity generation is likely. Because of the nature of production methods employed and the ease of installation, system implementation can be rapid. (Author) 29 refs

  3. Metagenomic data of fungal internal transcribed spacer from serofluid dish, a traditional Chinese fermented food

    Directory of Open Access Journals (Sweden)

    Peng Chen

    2016-03-01

    Full Text Available Serofluid dish (or Jiangshui, in Chinese, a traditional food in the Chinese culture for thousands of years, is made from vegetables by fermentation. In this work, microorganism community of the fermented serofluid dish was investigated by the culture-independent method. The metagenomic data in this article contains the sequences of fungal internal transcribed spacer (ITS regions of rRNA genes from 12 different serofluid dish samples. The metagenome comprised of 50,865 average raw reads with an average of 8,958,220 bp and G + C content is 45.62%. This is the first report on metagenomic data of fungal ITS from serofluid dish employing Illumina platform to profile the fungal communities of this little known fermented food from Gansu Province, China. The Metagenomic data of fungal internal transcribed spacer can be accessed at NCBI, SRA database accession no. SRP067411. Keywords: Serofluid dish, Jiangshui, Fungal ITS, Cultivation-independent, Microbial diversity

  4. Performance comparisons of dish type solar concentrator with mirror arrangements and receiver shapes

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Joo Hyun; Kim, Yong; Ma, Dae Sung; Seo, Tae Beom [Graduate School, Dept. of Mechanical Engineering, Inha Univ., Inchon (Korea, Republic of); Kang, Yong Heack [Korea Inst. of Energy Research, Daejeon (Korea, Republic of)

    2008-07-01

    The performance comparisons of dish type solar concentrators are numerically investigated. The dish type solar concentrator considered in this paper consists of a receiver and multi-faceted mirrors. In order to investigate the performance comparisons of dish type solar concentrators, six different mirror arrangements and four different receivers are considered. A parabolic-shaped perfect mirror of which diameter is 1.40 m is considered as the reference for the mirror arrangements. The other mirror arrangements consist of twelve identical parabolic-shaped mirror facets of which diameter are 0.405 m. Their total collecting areas, which are 1.545 m{sup 2}, are the same. Four different solar receiver shapes are a conical, a dome, a cylindrical, and a unicorn type. In order to investigate the thermal performance of the dish type solar concentrator, the radiative heat loss in the receiver should be calculated. For calculation, the net radiation method and the Monte-Carlo method are used. Also, because the thermal performance of the dish type solar concentrator can vary as the receiver surface temperature, the various surface temperatures are considered. Based on the calculation, the unicorn type has the best performance in receiver shapes and the STAR has the best performance in mirror arrangements except the perfect mirror. (orig.)

  5. Cultivation-independent comprehensive investigations on bacterial communities in serofluid dish, a traditional Chinese fermented food

    Directory of Open Access Journals (Sweden)

    Peng Chen

    2016-03-01

    Full Text Available Serofluid dish (or Jiangshui, in Chinese, a traditional food in the Chinese culture, is made from vegetables by fermentation. In this study, bacterial community of the fermented serofluid dish was assessed by Illumina amplicon sequencing. The metagenome comprised of 49,589 average raw reads with an average 11,497,917 bp and G+C content is 52.46%. This is the first report on V4 hyper-variable region of the 16S rRNA metagenome sequence employing Illumina platform to profile the microbial community of this little known fermented food from Gansu Province, China. The metagenome sequence can be accessed at NCBI, SRA database accession no. SRP065370. Keywords: Serofluid dish, Jiangshui, 16S rRNA, Cultivation-independent, Microbial diversity

  6. Wind load design methods for ground-based heliostats and parabolic dish collectors

    Energy Technology Data Exchange (ETDEWEB)

    Peterka, J A; Derickson, R G [Colorado State Univ., Fort Collins, CO (United States). Fluid Dynamics and Diffusion Lab.

    1992-09-01

    The purpose of this design method is to define wind loads on flat heliostat and parabolic dish collectors in a simplified form. Wind loads are defined for both mean and peak loads accounting for the protective influence of upwind collectors, wind protective fences, or other wind-blockage elements. The method used to define wind loads was to generalize wind load data obtained during tests on model collectors, heliostats or parabolic dishes, placed in a modeled atmospheric wind in a boundary-layer wind-tunnel at Colorado State University. For both heliostats and parabolic dishes, loads are reported for solitary collectors and for collectors as elements of a field. All collectors were solid with negligible porosity; thus the effects of porosity in the collectors is not addressed.

  7. High Efficiency, Low Cost Parabolic Dish System for Cogeneration of Electricity and Heat

    Science.gov (United States)

    Chayet, Haim; Lozovsky, Ilan; Kost, Ori; Loeckenhoff, Ruediger; Rasch, Klaus-Dieter

    2010-10-01

    Highly efficient combined heat and power generating system based on CPV technology using unique dish design consisting of multiple simple flat mirrors mounted on a plastic parabolic surface. The dish of total aperture area of 11 m2 focuses 10.3 kWp onto a heat and electricity generating receiver. The receiver comprises a water cooled, dense triple junction cell array of 176 cm2 aperture area. A unique arrangement of the cells compensates for the non-uniformity of the reflected flux. Depending on the flow rate, the temperature of the hot water can be adjusted to suit from temperatures for domestic use, to temperatures suited for process heat. The output of 2.3 kWp electrical and 5.5 kWp thermal power from one dish system represent 20 to 21% electrical and 50% thermal conversion efficiency adding to 70% overall system efficiency.

  8. Preparation of contemporary dishes and a functional drink using Japan's heirloom vegetable, Katsura-uri

    Directory of Open Access Journals (Sweden)

    Azusa Sasaki

    2018-03-01

    Full Text Available Background: The fruit of Katsura-uri, traditionally used in the preparation of pickles in Japan, is facing an extinction crisis. In addition to the traditional dishes prepared from Katsura-uri, alternative dishes using the fruit should be devised to increase consumer demands for the protection of the heirloom vegetable. We attempted designing new Katsura-uri contemporary dishes and assessed the application of Katsura-uri juice as a functional drink without raising blood glucose levels. Methods: Cooking experiments were conducted with Katsura-uri in its ripening stages, based on the advice from a licensed chef and a registered dietitian in Japan. In the questionnaire-based sensory evaluation, consumer acceptability of Katsura-uri juice was assessed. The blood glucose levels were measured after healthy volunteers consumed the juice. Results: We demonstrated six new Katsura-uri dishes. In the questionnaire-based sensory evaluation of Katsura-uri juice, the assessment values for taste and fragrance were high. In human trials, the levels of incremental area under the curve and glucose spike were significantly lower after consumption of Katsura-uri juice, as compared to those after consumption of muskmelon juice. Conclusion: Katsura-uri-containing contemporary dishes and juice would help continue the consumption of the vegetable. Based on the results of the questionnaire, we also concluded that the use of Katsura-uri as a functional drink without raising blood glucose levels is superior to its use as contemporary dishes. These findings provide useful strategies to protect Katsura-uri from extinction. Keywords: Blood glucose, Diabetes, Functional food, Heirloom vegetable, Traditional customs

  9. Design, Analysis and Optimization of a Solar Dish/Stirling System

    Directory of Open Access Journals (Sweden)

    Seyyed Danial Nazemi

    2016-02-01

    Full Text Available In this paper, a mathematical model by which the thermal and physical behavior of a solar dish/Stirling system was investigated, then the system was designed, analysed and optimized. In this regard, all of heat losses in a dish/Stirling system were calculated, then, the output net-work of the Stirling engine was computed, and accordingly, the system efficiency was worked out. These heat losses include convection and conduction heat losses, radiation heat losses by emission in the cavity receiver, reflection heat losses of solar energy in the parabolic dish, internal and external conduction heat losses, energy dissipation by pressure drops, and energy losses by shuttle effect in displacer piston in the Stirling engine. All of these heat losses in the parabolic dish, cavity receiver and Stirling engine were calculated using mathematical modeling in MatlabTM software. For validation of the proposed model, a 10 kW solar dish/Stirling system was designed and the simulation results were compared with the Eurodish system data with a reasonable degree of agreement. This model is used to investigate the effect of geometric and thermodynamic parameters including the aperture diameter of the parabolic dish and the cavity receiver, and the pressure of the compression space of the Stirling engine, on the system performance. By using the PSO method, which is an intelligent optimization technique, the total design was optimized and the optimal values of decision-making parameters were determined. The optimization has been done in two scenarios. In the first scenario, the optimal value of each designed parameter has been changed when the other parameters are equal to the designed case study parameters. In the second scenario, all of parameters were assumed in their optimal values. By optimization of the modeled dish/Stirling system, the total efficiency of the system improved to 0.60% in the first scenario and it increased from 21.69% to 22.62% in the second

  10. Differences in nutrient and energy contents of commonly consumed dishes prepared in restaurants v. at home in Hunan Province, China.

    Science.gov (United States)

    Jia, Xiaofang; Liu, Jiawu; Chen, Bo; Jin, Donghui; Fu, Zhongxi; Liu, Huilin; Du, Shufa; Popkin, Barry M; Mendez, Michelle A

    2018-05-01

    Eating away from home is associated with poor diet quality, in part due to less healthy food choices and larger portions. However, few studies account for the potential additional contribution of differences in food composition between restaurant- and home-prepared dishes. The present study aimed to investigate differences in nutrients of dishes prepared in restaurants v. at home. Eight commonly consumed dishes were collected in twenty of each of the following types of locations: small and large restaurants, and urban and rural households. In addition, two fast-food items were collected from ten KFC, McDonald's and food stalls. Five samples per dish were randomly pooled from every location. Nutrients were analysed and energy was calculated in composite samples. Differences in nutrients of dishes by preparation location were determined. Hunan Province, China. Na, K, protein, total fat, fatty acids, carbohydrate and energy in dishes. On average, both the absolute and relative fat contents, SFA and Na:K ratio were higher in dishes prepared in restaurants than households (P < 0·05). Protein was 15 % higher in animal food-based dishes prepared in households than restaurants (P<0·05). Quantile regression models found that, at the 90th quantile, restaurant preparation was consistently negatively associated with protein and positively associated with the percentage of energy from fat in all dishes. Moreover, restaurant preparation also positively influenced the SFA content in dishes, except at the highest quantiles. These findings suggest that compared with home preparation, dishes prepared in restaurants in China may differ in concentrations of total fat, SFA, protein and Na:K ratio, which may further contribute, beyond food choices, to less healthy nutrient intakes linked to eating away from home.

  11. 78 FR 59633 - Wireless Telecommunications Bureau Opens Docket To Seek Comment on DISH Network Corporation's...

    Science.gov (United States)

    2013-09-27

    ... 9, 2013, the DISH Network Corporation, on behalf of its wholly-owned subsidiaries, Gamma Acquisition... held by its wholly-owned subsidiaries, Gamma Acquisition LLC (Call Signs T060430001-T060430176) and New... Commission's Secretary must be delivered to FCC Headquarters at 445 12th Street SW., Room TW-A325, Washington...

  12. Combined Heat & Power Using the Infinia Concentrated Solar CHP PowerDish System

    Science.gov (United States)

    2013-08-01

    Executive Orders FOB - Forward Operating Base FPSE - Free Piston Stirling Engine GHG - Greenhouse Gas ICC - International Code Council IMA... Stirling Engine (FPSE) for military, commercial, and space applications for almost 30 years. These developments have included multiple fuel types...product for its Free Piston Stirling Engine operating on solar energy for electricity production, called the PowerDishTM, a reasonable extension for

  13. A small scale cell culture system to analyze mechanobiology using reporter gene constructs and polyurethane dishes

    DEFF Research Database (Denmark)

    Seefried, Lothar; Mueller-Deubert, Sigrid; Wentzer, Thomas Schwarz

    2010-01-01

    of mechanotransduction and its crosstalk with biochemically induced signal transduction, AP1 and SP1 luciferase reporter gene constructs were cloned and transfected into various cell lines and primary cells. A newly developed bioreactor and small-scale 24-well polyurethane dishes were used to apply cyclic stretching...

  14. Nutritional Quality of School Meals in France: Impact of Guidelines and the Role of Protein Dishes

    Directory of Open Access Journals (Sweden)

    Florent Vieux

    2018-02-01

    Full Text Available In France, school meals must comply with 15 frequency criteria (FC expressed as nutritional requirements (e.g., “starters containing more than 15% fat served no more than four times out of 20” in a series of 20 consecutive meals. The objective was to assess, for the first time, the nutritional impact of complying with French school food FC. Based on 40 series of meals actually served in primary schools (“observed series”, several scenarios (1600 series per scenario of compliance or non-compliance with FC were simulated, and nutritional quality was assessed via the mean adequacy ratio (MAR/2000 kcal. In the observed series, only 9.7 FC on average (range 4–14 were fulfilled. In the simulated series: (i MAR was positively associated with FC compliance level, with the highest MAR obtained with complete compliance; (ii MAR decreased when meat or fish-based dishes were replaced by dishes without meat or fish; and (iii removing the protein dish without replacement led to the lowest MAR. This study demonstrates that French school food guidelines ensure good nutritional quality of food services. It also shows that generalizing the service of meals without meat or fish would deteriorate overall nutritional quality, highlighting the need to define the composition of vegetarian dishes and their frequency of service to children.

  15. THE HYDROGEN EPOCH OF REIONIZATION ARRAY DISH. I. BEAM PATTERN MEASUREMENTS AND SCIENCE IMPLICATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Neben, Abraham R.; Hewitt, Jacqueline N.; Ewall-Wice, Aaron [MIT Kavli Institute, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Bradley, Richard F. [Department of Electrical and Computer Engineering, University of Virginia, Charlottesville, VA 22904 (United States); DeBoer, David R.; Parsons, Aaron R.; Ali, Zaki S.; Cheng, Carina; Patra, Nipanjana; Dillon, Joshua S. [Department of Astronomy, University of California, Berkeley, CA (United States); Aguirre, James E.; Kohn, Saul A. [Department of Physics and Astronomy, University of Pennsylvania, Philadelphia, PA (United States); Thyagarajan, Nithyanandan; Bowman, Judd; Jacobs, Daniel C. [Arizona State University, School of Earth and Space Exploration, Tempe, AZ 85287 (United States); Dickenson, Roger; Doolittle, Phillip; Egan, Dennis; Hedrick, Mike; Klima, Patricia J. [National Radio Astronomy Observatory, Charlottesville, VA (United States); and others

    2016-08-01

    The Hydrogen Epoch of Reionization Array (HERA) is a radio interferometer aiming to detect the power spectrum of 21 cm fluctuations from neutral hydrogen from the epoch of reionization (EOR). Drawing on lessons from the Murchison Widefield Array and the Precision Array for Probing the EOR, HERA is a hexagonal array of large (14 m diameter) dishes with suspended dipole feeds. The dish not only determines overall sensitivity, but also affects the observed frequency structure of foregrounds in the interferometer. This is the first of a series of four papers characterizing the frequency and angular response of the dish with simulations and measurements. In this paper, we focus on the angular response (i.e., power pattern), which sets the relative weighting between sky regions of high and low delay and thus apparent source frequency structure. We measure the angular response at 137 MHz using the ORBCOMM beam mapping system of Neben et al. We measure a collecting area of 93 m{sup 2} in the optimal dish/feed configuration, implying that HERA-320 should detect the EOR power spectrum at z ∼ 9 with a signal-to-noise ratio of 12.7 using a foreground avoidance approach with a single season of observations and 74.3 using a foreground subtraction approach. Finally, we study the impact of these beam measurements on the distribution of foregrounds in Fourier space.

  16. Modelling dishes and exploring culinary 'precisions': the two issues of molecular gastronomy.

    Science.gov (United States)

    This, Hervé

    2005-04-01

    The scientific strategy of molecular gastronomy includes modelling 'culinary definitions' and experimental explorations of 'culinary precisions'. A formalism that describes complex dispersed systems leads to a physical classification of classical sauces, as well as to the invention of an infinite number of new dishes.

  17. Nutritional Quality of School Meals in France: Impact of Guidelines and the Role of Protein Dishes.

    Science.gov (United States)

    Vieux, Florent; Dubois, Christophe; Duchêne, Christelle; Darmon, Nicole

    2018-02-13

    In France, school meals must comply with 15 frequency criteria (FC) expressed as nutritional requirements (e.g., "starters containing more than 15% fat served no more than four times out of 20") in a series of 20 consecutive meals. The objective was to assess, for the first time, the nutritional impact of complying with French school food FC. Based on 40 series of meals actually served in primary schools ("observed series"), several scenarios (1600 series per scenario) of compliance or non-compliance with FC were simulated, and nutritional quality was assessed via the mean adequacy ratio (MAR/2000 kcal). In the observed series, only 9.7 FC on average (range 4-14) were fulfilled. In the simulated series: (i) MAR was positively associated with FC compliance level, with the highest MAR obtained with complete compliance; (ii) MAR decreased when meat or fish-based dishes were replaced by dishes without meat or fish; and (iii) removing the protein dish without replacement led to the lowest MAR. This study demonstrates that French school food guidelines ensure good nutritional quality of food services. It also shows that generalizing the service of meals without meat or fish would deteriorate overall nutritional quality, highlighting the need to define the composition of vegetarian dishes and their frequency of service to children.

  18. THE HYDROGEN EPOCH OF REIONIZATION ARRAY DISH. I. BEAM PATTERN MEASUREMENTS AND SCIENCE IMPLICATIONS

    International Nuclear Information System (INIS)

    Neben, Abraham R.; Hewitt, Jacqueline N.; Ewall-Wice, Aaron; Bradley, Richard F.; DeBoer, David R.; Parsons, Aaron R.; Ali, Zaki S.; Cheng, Carina; Patra, Nipanjana; Dillon, Joshua S.; Aguirre, James E.; Kohn, Saul A.; Thyagarajan, Nithyanandan; Bowman, Judd; Jacobs, Daniel C.; Dickenson, Roger; Doolittle, Phillip; Egan, Dennis; Hedrick, Mike; Klima, Patricia J.

    2016-01-01

    The Hydrogen Epoch of Reionization Array (HERA) is a radio interferometer aiming to detect the power spectrum of 21 cm fluctuations from neutral hydrogen from the epoch of reionization (EOR). Drawing on lessons from the Murchison Widefield Array and the Precision Array for Probing the EOR, HERA is a hexagonal array of large (14 m diameter) dishes with suspended dipole feeds. The dish not only determines overall sensitivity, but also affects the observed frequency structure of foregrounds in the interferometer. This is the first of a series of four papers characterizing the frequency and angular response of the dish with simulations and measurements. In this paper, we focus on the angular response (i.e., power pattern), which sets the relative weighting between sky regions of high and low delay and thus apparent source frequency structure. We measure the angular response at 137 MHz using the ORBCOMM beam mapping system of Neben et al. We measure a collecting area of 93 m 2 in the optimal dish/feed configuration, implying that HERA-320 should detect the EOR power spectrum at z ∼ 9 with a signal-to-noise ratio of 12.7 using a foreground avoidance approach with a single season of observations and 74.3 using a foreground subtraction approach. Finally, we study the impact of these beam measurements on the distribution of foregrounds in Fourier space.

  19. Optical analysis and performance evaluation of a solar parabolic dish concentrator

    Directory of Open Access Journals (Sweden)

    Pavlović Saša R.

    2016-01-01

    Full Text Available In this study, the optical design of a solar parabolic dish concentrator is presented. The parabolic dish concentrator consists from 11 curvilinear trapezoidal reflective petals made of polymethyl methacrylate with special reflective coating. The dish diameter is equal to 3.8 m and the theoretical focal point distance is 2.26 m. Numerical simulations are made with the commercial software TracePro from Lambda Research, USA, and the final optimum position between absorber and reflector was calculated to 2.075 m; lower than focus distance. This paper presents results for the optimum position and the optimum diameter of the receiver. The decision for selecting these parameters is based on the calculation of the total flux over the flat and corrugated pipe receiver surface; in its central region and in the peripheral region. The simulation results could be useful reference for designing and optimizing of solar parabolic dish concentrators as for as for CFD analysis, heat transfer and fluid flow analysis in corrugated spiral heat absorbers. [Projekat Ministarstva nauke Republike Srbije, br. III42006: Research and development of energy and environmentally highly effective polygeneration systems based on renewable energy resources i br. III45016: Fabrication and characterization of nanophotonic functional structures in biomedicine and informatics

  20. Mobile Satellite Reception with a Virtual Satellite Dish based on a Reconfigurable Multi-Processor Architecture

    NARCIS (Netherlands)

    van de Burgwal, M.D.; Rovers, K.C.; Blom, K.C.H.; Kokkeler, Andre B.J.; Smit, Gerardus Johannes Maria

    2011-01-01

    Traditionally, mechanically steered dishes or analog phased array beamforming systems have been used for radio frequency receivers, where strong directivity and high performance were much more important than low-cost requirements. Real-time controlled digital phased array beamforming could not be

  1. Fort Huachuca to Benefit from New Solar Technology: Dish-Stirling System Couples Solar Power with Engine to Generate Electricity

    National Research Council Canada - National Science Library

    1995-01-01

    ... in partnership with industry. A prototype dish-Stirling solar system, which consists of a large dish of solar concentrators and a Stirling heat engine, will be installed at Fort Huachuca in July and should be in operation about two weeks later...

  2. Healthier side dishes at restaurants: an analysis of children’s perspectives, menu content, and energy impacts

    Science.gov (United States)

    2014-01-01

    Background Children consume restaurant-prepared foods at high rates, suggesting that interventions and policies targeting consumption of these foods have the potential to improve diet quality and attenuate excess energy intake. One approach to encouraging healthier dietary intake in restaurants is to offer fruits and vegetables (FV) as side dishes, as opposed to traditional, energy-dense accompaniments like French fries. The aims of the current study were to examine: children's views about healthier side dishes at restaurants; current side dish offerings on children's menus at leading restaurants; and potential energy reductions when substituting FV side dishes in place of French fries. Methods To investigate children’s attitudes, a survey was administered to a nationally representative sample of U.S. 8- to 18-year-olds (n = 1178). To examine current side dish offerings, children's menus from leading quick service (QSR; n = 10) and full service restaurant chains (FSR; n = 10) were analyzed. Energy reductions that could result from substituting commonly-offered FV side dishes for French fries were estimated using nutrition information corresponding to the children's menu items. Results Two-thirds of children reported that they would not feel negatively about receiving FV sides instead of French fries with kids' meals. Liking/taste was the most common reason that children gave to explain their attitudes about FV side dishes. Nearly all restaurants offered at least 1 FV side dish option, but at most restaurants (60% of QSR; 70% of FSR), FV sides were never served by default. Substituting FV side dishes for French fries yielded an average estimated energy reduction of at least 170 calories. Conclusions Results highlight some healthy trends in the restaurant context, including the majority of children reporting non-negative attitudes about FV side dishes and the consistent availability of FV side dish options at leading QSR and FSR. Yet the minority of

  3. Negative-ion beam surface modification of tissue-culture polystyrene dishes for changing hydrophilic and cell-attachment properties

    International Nuclear Information System (INIS)

    Tsuji, H.; Satoh, H.; Ikeda, S.; Ikemura, S.; Gotoh, Y.; Ishikawa, J.

    1999-01-01

    Negative-silver-ion implantation into tissue-culture polystyrene (TCPS) dishes was investigated and it was found to modify hydrophilic and cell attachment properties of the dishes. Negative-ion implantation has an advantage of being almost free of surface charging, and is a suitable method for implantation into insulators such as polymers. Negative silver ions are used due to the antibacterial property of silver. Ag-implanted TCPS dishes had a contact angle larger than the normal value of 66 deg. of unimplanted dishes. The contact angle of water had a strong dependence on the ion energy rather than the dose. As a cell-culture experiment, human umbilical vascular endothelial cell (HUVEC) was used in unimplanted and Ag-implanted TCPS dishes, the implantation removed the cell-attachment property of the surface. In implantation with a mask with a striped pattern, most attached cells of HUVEC were in the unimplanted region aligned along a stripe direction

  4. International off-grid market assessment for dish/Stirling systems

    International Nuclear Information System (INIS)

    Lilienthal, P.; Campbell, K.

    1998-01-01

    Several features of dish/Stirling technology offer potential advantages for off-grid power generation. Dish/Stirling technology's size, modularity, the ease with which it might be hybridized with a storable fuel, the elimination of batteries and inverters, and the production of pure sine-wave AC power without a diesel all indicate that a reliable dish/Stirling module could fit well into an off-grid electrification scheme. At the same time, a combination of factors makes success in off-grid applications difficult, regardless of the technology under consideration. Obstacles include consumer expectations (formed by a long history of subsidies) that electricity should be cheap, existing support infrastructure, and the economic resources of rural communities. Cost is always a factor, but reliability and access to parts and service have been more significant barriers so far in the establishment of renewables. This paper summarizes a much more extensive market assessment. Initial research indicates that a reliable 25 kW dish/Stirling system with reasonable servicing requirements could compete well with other off-grid power systems at a cost considered achievable at early production levels ($3,500 per kW). However, by itself the off-grid power market in regions with adequate solar insolation and inviting political regimes does not justify an adequate scale of production. It is estimated that the aggregate market in five of the largest and most promising countries for which adequate information was available could be 23,000 to 38,000 units of 25 kW dish/Stirling systems. Including the rest of the developing world could more than double this number. However, at a reasonable initial market penetration rate of 1% per year this market is not sufficient, by itself, for the mass production rates required to achieve the necessary economies of scale

  5. A microfluidic-based lid device for conventional cell culture dishes to automatically control oxygen level.

    Science.gov (United States)

    Lee, Seung Yeob; Yang, Sung

    2018-04-25

    Most conventional hypoxic cell culture systems undergo reoxygenation during experimental manipulations, resulting in undesirable effects including the reduction of cell viability. A lid device was developed herein for conventional cell culture dishes to resolve this limitation. The integration of multilayered microfluidic channels inside a thin membrane was designed to prevent the reoxygenation caused by reagent infusion and automatically control the oxygen level. The experimental data clearly show the reducibility of the dissolved oxygen in the infusing reagent and the controllability of the oxygen level inside the dish. The feasibility of the device for hypoxia studies was confirmed by HIF-1α experiments. Therefore, the device could be used as a compact and convenient hypoxic cell culture system to prevent reoxygenation-related issues.

  6. Effect of radiation on preservation of convenient dish 'bowl-shape packed pig elbow'

    International Nuclear Information System (INIS)

    Wang Keqin; Chen Jingping; Li Wenge; Peng Weizheng

    2005-01-01

    The suitable parameters for radiation processing were investiqated by analyzing the microload of material and product, and radiation effect on the preservation of convenient dish 'bowl-shape packed pig elbow'. The results showed the store period of the product could be extended 2-6 month by 4.0-6.0 kGy radiation at different storage temperature. The sensory, physical and chemical index of the products met the requirement of relevant national standard of food hygiene. (authors)

  7. Who should do the dishes now? Revisiting gender and housework in contemporary urban South Wales

    OpenAIRE

    Mannay, Dawn

    2016-01-01

    This chapter revisits Jane Pilcher’s (1994) seminal work ‘Who should do the dishes? Three generations of Welsh women talking about men and housework’, which was originally published in Our Sister’s Land: the changing identities of women in Wales. As discussed in the introductory chapter, I began revisiting classic Welsh studies as part of my doctoral study Mothers and daughters on the margins: gender, generation and education (Mannay, 2012); this lead to the later publication of a revisiting ...

  8. Modeling the small-scale dish-mounted solar thermal Brayton cycle

    Science.gov (United States)

    Le Roux, Willem G.; Meyer, Josua P.

    2016-05-01

    The small-scale dish-mounted solar thermal Brayton cycle (STBC) makes use of a sun-tracking dish reflector, solar receiver, recuperator and micro-turbine to generate power in the range of 1-20 kW. The modeling of such a system, using a turbocharger as micro-turbine, is required so that optimisation and further development of an experimental setup can be done. As a validation, an analytical model of the small-scale STBC in Matlab, where the net power output is determined from an exergy analysis, is compared with Flownex, an integrated systems CFD code. A 4.8 m diameter parabolic dish with open-cavity tubular receiver and plate-type counterflow recuperator is considered, based on previous work. A dish optical error of 10 mrad, a tracking error of 1° and a receiver aperture area of 0.25 m × 0.25 m are considered. Since the recuperator operates at a very high average temperature, the recuperator is modeled using an updated ɛ-NTU method which takes heat loss to the environment into consideration. Compressor and turbine maps from standard off-the-shelf Garrett turbochargers are used. The results show that for the calculation of the steady-state temperatures and pressures, there is good comparison between the Matlab and Flownex results (within 8%) except for the recuperator outlet temperature, which is due to the use of different ɛ-NTU methods. With the use of Matlab and Flownex, it is shown that the small-scale open STBC with an existing off-the-shelf turbocharger could generate a positive net power output with solar-to-mechanical efficiency of up to 12%, with much room for improvement.

  9. Finite time thermodynamic analysis and optimization of solar-dish Stirling heat engine with regenerative losses

    Directory of Open Access Journals (Sweden)

    Sharma Arjun

    2011-01-01

    Full Text Available The present study investigates the performance of the solar-driven Stirling engine system to maximize the power output and thermal efficiency using the non-linearized heat loss model of the solar dish collector and the irreversible cycle model of the Stirling engine. Finite time thermodynamic analysis has been done for combined system to calculate the finite-rate heat transfer, internal heat losses in the regenerator, conductive thermal bridging losses and finite regeneration process time. The results indicate that exergy efficiency of dish system increases as the effectiveness of regenerator increases but decreases with increase in regenerative time coefficient. It is also found that optimal range of collector temperature and corresponding concentrating ratio are 1000 K~1400 K and 1100~1400, respectively in order to get maximum value of exergy efficiency. It is reported that the exergy efficiency of this dish system can reach the maximum value when operating temperature and concentrating ratio are 1150 K and 1300, respectively.

  10. Occurrence of heterocyclic amines in several home-cooked meat dishes of the Spanish diet.

    Science.gov (United States)

    Busquets, R; Bordas, M; Toribio, F; Puignou, L; Galceran, M T

    2004-03-25

    Heterocyclic amines (HAs) were determined in several of the most frequently eaten meat dishes in Spain such as fried beef hamburger, fried pork loin, fried chicken breast, fried pork sausages, griddled chicken breast, griddled lamb steak and griddled beef steak. All of the products tested were household cooked. The HAs were analysed in the selected meat dishes using an analytical method based on solid-phase extraction followed by liquid chromatography coupled to tandem mass spectrometry. DMIP, MeIQx, 4,8-DiMeIQx, Norharman, Harman, PhIP, Trp-P-1, AalphaC and MeAalphaC were the amines most frequently found at concentrations of up to 47 ng g(-1) of cooked meat. Glu-P-2, IQ, MeIQ, Glu-P-1, 7,8-DiMeIQx and Trp-P-2 were only found in a few of the meat dishes and their concentrations were lower than 1 ng g(-1) of cooked meat. The highest amounts of HAs, especially PhIP and DMIP, were formed in fried chicken breast and the lowest were formed in fried beef hamburger and in fried pork sausages. Daily intake of HAs in Spain was estimated at 606 ng of mutagenic HAs per capita and day, DMIP and PhIP being the main contributors.

  11. Nano Petri dishes: a new polystyrene platform for studying cell-nanoengineered surface interactions

    International Nuclear Information System (INIS)

    Cha, Kyoung Je; Na, Moon-Hee; Kim, Hyung Woo; Kim, Dong Sung

    2014-01-01

    In this study, we fabricated and fully characterized a new type of polystyrene (PS) cell-culture platform containing nanoengineered surfaces (NES), referred to as a nano Petri dish, which can be used at the transition stage of basic cell–NES interaction studies for clinical applications. Nano-injection molding in this study was used for the mass production of the nano Petri dish having nanopore arrays. The effects of processing parameters of the injection molding on the replication quality of the nanopore arrays were quantitatively evaluated by means of design of experiments based on the Taguchi method. This allowed efficient and reliable cell culture studies by providing large numbers of the same dishes, in addition to removing the fixation step of the NES plates inside the cell-culture container. Physical, chemical and mechanical properties of the NES, as well as cell behavior including attachment and proliferation of human osteosarcoma MG-63 cells on the NES, were then characterized, with and without the oxygen plasma surface treatment. (paper)

  12. Nano Petri dishes: a new polystyrene platform for studying cell-nanoengineered surface interactions

    Science.gov (United States)

    Cha, Kyoung Je; Na, Moon-Hee; Kim, Hyung Woo; Kim, Dong Sung

    2014-05-01

    In this study, we fabricated and fully characterized a new type of polystyrene (PS) cell-culture platform containing nanoengineered surfaces (NES), referred to as a nano Petri dish, which can be used at the transition stage of basic cell-NES interaction studies for clinical applications. Nano-injection molding in this study was used for the mass production of the nano Petri dish having nanopore arrays. The effects of processing parameters of the injection molding on the replication quality of the nanopore arrays were quantitatively evaluated by means of design of experiments based on the Taguchi method. This allowed efficient and reliable cell culture studies by providing large numbers of the same dishes, in addition to removing the fixation step of the NES plates inside the cell-culture container. Physical, chemical and mechanical properties of the NES, as well as cell behavior including attachment and proliferation of human osteosarcoma MG-63 cells on the NES, were then characterized, with and without the oxygen plasma surface treatment.

  13. Cascade system using both trough system and dish system for power generation

    International Nuclear Information System (INIS)

    Zhang, Cheng; Zhang, Yanping; Arauzo, Inmaculada; Gao, Wei; Zou, Chongzhe

    2017-01-01

    Highlights: • A novel solar cascade system using both trough and dish collectors is proposed. • Heat rejected by the Stirling engines is collected by the condensed water. • The directions to increase the efficiency improvement has been pointed out • Influence of flow type of heating/cooling fluids of Stirling engines is considered. - Abstract: This paper represents a novel solar thermal cascade system using both trough and dish systems for power generation. An effective structure using the condensed fluid of Rankine cycle to cool the Stirling engines to use the heat released by Stirling engines was proposed. The cascade system model with different fluid circuits was developed. The models of some important components of the system, such as dish collector, trough collector and Stirling engine array, are presented with detail explanation in this paper. Corresponding stand-alone systems were also developed for comparison. Simulations were conducted with the models to find out efficiency difference between cascade system and corresponding stand-alone systems. The directions to increase the efficiency difference were also considered. Results show that the cascade system can achieve a higher efficiency with a high solar irradiance (>550 W/m"2). The flow type of fluids between heating and cooling Stirling engine array is also required to concern on designing a cascade system with Stirling engine array.

  14. Nutritional value of traditional Italian meat-based dishes: influence of cooking methods and recipe formulation.

    Science.gov (United States)

    D'Evoli, L; Salvatore, P; Lucarini, M; Nicoli, S; Aguzzi, A; Gabrielli, P; Lombardi-Boccia, G

    2009-01-01

    The present study provides a picture of the compositional figure and nutritive value of meat-based dishes typical of Italian culinary tradition. Recipes specific for a bovine meat cut (top-side) were selected among the most widespread ones in Italy: in pan, pizzaiola, cutlet, meat ball, and escalope. The total fat and cholesterol content varied depending on the ingredients utilized (extra-virgin olive oil, parmesan, egg). Meat-based dishes that utilized extra-virgin olive oil showed a significant reduction in palmitic and stearic acids and a parallel increase in oleic acid compared with raw meat; furthermore, the ratio among saturated fatty acids, monounsaturated fatty acids and polyunsaturated fatty acids shifted in favour of monounsaturated fatty acids. B vitamins were affected at different extent by heating; by contrast, vitamin E content increased because of the new sources of this vitamin, which masked losses due to heating. Ingredients (parmesan, discretionary salt) induced significant increases in the calcium and sodium concentrations compared with raw meat. The total iron content did not show marked differences in most of the meat-based dishes compared with raw meat; by contrast, losses in the heme-iron concentration were detected depending on the severity of heating treatments. Our findings suggest that heme iron, because of its important health aspects, might be a useful index of the nutritional quality of cooked meats.

  15. Mount for continuously orienting a collector dish in a system adapted to perform both diurnal and seasonal solar tracking

    Science.gov (United States)

    Brantley, L. W., Jr.; Lawson, B. D. (Inventor)

    1977-01-01

    A collector dish is continuously oriented toward the sun in a system adapted to perform both diurnal and seasonal solar tracking. The mount is characterized by a rigid, angulated axle having a linear midportion supporting a collector dish, and oppositely extended end portions normally related to the midportion of the axle and received in spaced journals. The longitudinal axis of symmetry for the midportion of the axle is coincident with a seasonal axis while the axes of the journals are coincident with a diurnal axis paralleling the earth's polar axis. Drive means are provided for periodically displacing the axle about the diurnal axis at a substantially constant rate, while other drive means are provided for periodically indexing the dish through 1 deg about the seasonal axis whereby the position of the dish relative to the axle is varied for accommodating seasonal tracking as changes in the angle of inclination of the polar axis occurs.

  16. MODELLING OF AN INEXPENSIVE 9M SATELLITE DISH FROM 3D POINT CLOUDS CAPTURED BY TERRESTRIAL LASER SCANNERS

    Directory of Open Access Journals (Sweden)

    D. Belton

    2012-09-01

    Full Text Available This paper presents the use of Terrestrial laser scanners (TLS to model the surface of satellite dish. In this case, the dish was an inexpensive 9m parabolic satellite dish with a mesh surface, and was to be utilised in radio astronomy. The aim of the modelling process was to determine the deviation of the surface away from its true parabolic shape, in order to estimate the surface efficiency with respect to its principal receiving frequency. The main mathematical problems were the optimal and unbiased estimation the orientation of the dish and the fitting of a parabola to the local orientation or coordinate system, which were done by both orthogonal and algebraic minimization using the least-squares method. Due to the mesh structure of the dish, a classification method was also applied to filter out erroneous points being influenced by the supporting structure behind the dish. Finally, a comparison is performed between the ideal parabolic shape, and the data collected from three different temporal intervals.

  17. Design and implementation of a 38 kW dish-Stirling concentrated solar power system

    Science.gov (United States)

    Yan, J.; Peng, Y. D.; Cheng, Z. R.; Liu, F. M.; Tang, X. H.

    2017-11-01

    Dish-Stirling concentrated solar power system (DS-CSP) is an important pathway for converting solar energy into electricity at high efficiency. In this study, a rated power 38 kW DS-CSP system was developed (installed in Xiangtan Electric Manufacturing Group). The heat engine adopted the alpha-type four cylinders double-acting Stirling engine (Stirling Biopower Flexgen S260). The absorber flux distribution simulation was conducted using ray tracing method and then the 204 m2 parabolic dish concentrator system (diameter is 17.70 m and focal length is 9.49 m) with single concentrator plus single pillar supporting has been designed and built. A water-cooled disc target and an absorber imitation device were adopted to test the tracking performance of the dish concentrator system, homogeneity of the focal spot and flux distribution of the absorber. Finally, the S260 Stirling engine was installed on the focal position of the dish concentrator and then the net output power date of the 38 kW DS-CSP system was tested. The absorber overheating problem on the DS-CSP system performance was discussed when the DS-CSP system was installed in different locations. The testing result shows that this system achieved the net output power of 38 kW and solar-to-electricity efficiency (SEE) of 25.3% with the direct normal irradiation (DNI) at 750 W/m2. The net output power can further increase to 40.5 kW with the SEE of 26.6% when the DNI reaches up to the maximum of 761 W/m2. The net output power of the 38 kW DS-CSP system has a linear function relationship with the DNI. The fitting function is Net power output=0.1003×DNI-36.129, where DNI is at the range of 460∼761 W/m2. This function could be used to predict the amount of the 38 kW DS-CSP system annual generation power.

  18. Who should do the dishes now? exploring gender and housework in contemporary urban South Wales

    OpenAIRE

    Mannay, Dawn

    2014-01-01

    This paper revisits Jane Pilcher’s (1994) seminal chapter from Our Sisters’ Land: The Changing Identities of Women in Wales - ‘Who should do the dishes? Three generations of Welsh women talking about men and housework’. Two decades on from the original study, the paper explores this question in contemporary south Wales by drawing upon data generated in a study of mothers and daughters residing in a Welsh, marginalised, urban housing area. Mothers of daughters in the two eldest groups tended t...

  19. The kinematic Stirling engine as an energy conversion subsystem for paraboloidal dish solar thermal plants

    Science.gov (United States)

    Bowyer, J. M.

    1984-01-01

    The potential of a suitably designed and economically manufactured Stirling engine as the energy conversion subsystem of a paraboloidal dish-Stirling solar thermal power module was estimated. Results obtained by elementary cycle analyses were shown to match quite well the performance characteristics of an advanced kinematic Stirling engine, the United Stirling P-40, as established by current prototypes of the engine and by a more sophisticated analytic model of its advanced derivative. In addition to performance, brief consideration was given to other Stirling engine criteria such as durability, reliability, and serviceability. Production costs were not considered here.

  20. Flavor Enhancer From Catfish (Clarias batrachus) Bekasam Powder and Angiotensin-I-Converting Enzyme (ACE) Inhibitory Activity in Various Dishes

    Science.gov (United States)

    Lestari, Yanesti N.; Murwani, Retno; Agustini, Tri W.

    2018-02-01

    Flavor enhancer is characterized by high glutamic acid content and it can be obtained from fermented food such as Bekasam. Fermented food had inhibitory effect on Angiotensin-I-Converting Enzyme (ACE) activity which is advantageous for hypertension. However, such activity was not known to sustain in food system. The aim of this research was to study addition of flavour enhancer from Catfish Bekasam Powder (CBP) in various food systems and to determine the ACE inhibitory (ACEI) activity in the food system. Four food system consisted of carrot, champignon, and chicken meat dishes were boiled in water and added with CBP or MSG. Each food system was added with graded level of CBP (0%; 0.5%; 0.8%; 1.1%; and 1,4%) and for control monosodium glutamate (MSG) was used. ACEI activity in each food system and organoleptic test using multiple comparison differentiation on 15 semi-trained panellists were determined. The results showed that there were fluctuation of ACEI activity in the carrot, champignon, and chicken meat dishes (p=0.017; 0.043; and 0.032). The MSG containing dishes showed the lowest ACEI activity. Addition of graded level of CBP on carrot, champignon, and chicken meat dishes were directly proportional to glutamic acid content but inversely proportional to ACEI activity (pacid content but reduced ACE-inhibitory activity significantly (p<0.05). Comparing CBP to MSG addition in champignon dish revealed that increasing level of CBP increased the flavour preference of the panellists. On the contrary the higher the addition CBP in noodle and chicken meat dishes the worse were the flavour score (p<0.05). It can be concluded that the addition of CBP as flavour enhancer on various dishes can deliver better flavour and ACE-inhibitory activity than the addition of commercial MSG.

  1. Immobilization of sericin molecules via amorphous carbon plasma modified-polystyrene dish for serum-free culture

    International Nuclear Information System (INIS)

    Tunma, Somruthai; Song, Doo-Hoon; Kim, Si-Eun; Kim, Kyoung-Nam; Han, Jeon-Geon; Boonyawan, Dheerawan

    2013-01-01

    In this study, we focused on sericin hydrolysates, originating from silkworm used in serum-free human bone marrow-derived mesenchymal stem cells (hBM-MSCs) culture. We reported the effect of a covalent linkage between a bioactive protein molecule and polystyrene dish surface via a carbon intermediate layer which can slow down the release rate of protein compounds into the phosphate buffer saline (PBS) solution. Films of amorphous carbon (a-C) and functionalized-carbon were deposited on PS culture dish surfaces by using a DC magnetron sputtering system and RF PECVD system. We found that a-C based-films can increase the hydrophilicity and biocompatibility of polystyrene (PS) dishes, especially a-C films and a-C:N 2 films showed good attachment of hBM-MSCs at 24 h. However, in the case of silica surface (a-C:SiO x films), the cells showed a ragged and unattached boundary resulting from the presence of surface silanol groups. For the UV–vis absorbance, all carbon modified-PS dishes showed a lower release rate of sericin molecules into PBS solution than PS control. This revealed that the functionalized carbon could be enhanced by specific binding properties with given molecules. The carbon-coated PS dishes grafting with sericin protein were used in a serum-free condition. We also found that hBM-MSCs have higher percentage of proliferated cells at day 7 for the modified dishes with carbon films and coated with sericin than the PS control coated with sericin. The physical film properties were measured by atomic force microscopy (AFM), scanning electron microscope (SEM) and contact angle measurement. The presence of -NH 2 groups of sericin compounds on the PS dish was revealed by Fourier transform infrared spectroscopy (FTIR). The stability of covalent bonds of sericin molecules after washing out ungrafted sericin was confirmed by X-ray photoelectron spectroscopy (XPS).

  2. Immobilization of sericin molecules via amorphous carbon plasma modified-polystyrene dish for serum-free culture

    Science.gov (United States)

    Tunma, Somruthai; Song, Doo-Hoon; Kim, Si-Eun; Kim, Kyoung-Nam; Han, Jeon-Geon; Boonyawan, Dheerawan

    2013-10-01

    In this study, we focused on sericin hydrolysates, originating from silkworm used in serum-free human bone marrow-derived mesenchymal stem cells (hBM-MSCs) culture. We reported the effect of a covalent linkage between a bioactive protein molecule and polystyrene dish surface via a carbon intermediate layer which can slow down the release rate of protein compounds into the phosphate buffer saline (PBS) solution. Films of amorphous carbon (a-C) and functionalized-carbon were deposited on PS culture dish surfaces by using a DC magnetron sputtering system and RF PECVD system. We found that a-C based-films can increase the hydrophilicity and biocompatibility of polystyrene (PS) dishes, especially a-C films and a-C:N2 films showed good attachment of hBM-MSCs at 24 h. However, in the case of silica surface (a-C:SiOx films), the cells showed a ragged and unattached boundary resulting from the presence of surface silanol groups. For the UV-vis absorbance, all carbon modified-PS dishes showed a lower release rate of sericin molecules into PBS solution than PS control. This revealed that the functionalized carbon could be enhanced by specific binding properties with given molecules. The carbon-coated PS dishes grafting with sericin protein were used in a serum-free condition. We also found that hBM-MSCs have higher percentage of proliferated cells at day 7 for the modified dishes with carbon films and coated with sericin than the PS control coated with sericin. The physical film properties were measured by atomic force microscopy (AFM), scanning electron microscope (SEM) and contact angle measurement. The presence of sbnd NH2 groups of sericin compounds on the PS dish was revealed by Fourier transform infrared spectroscopy (FTIR). The stability of covalent bonds of sericin molecules after washing out ungrafted sericin was confirmed by X-ray photoelectron spectroscopy (XPS).

  3. Immobilization of sericin molecules via amorphous carbon plasma modified-polystyrene dish for serum-free culture

    Energy Technology Data Exchange (ETDEWEB)

    Tunma, Somruthai [The Graduate School, Chiang Mai University, 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics (ThEP), 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand); Song, Doo-Hoon [Research Center for Orofacial Hard Tissue Regeneration, College of Dentistry, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-752 (Korea, Republic of); Kim, Si-Eun; Kim, Kyoung-Nam [Research Center for Orofacial Hard Tissue Regeneration, College of Dentistry, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-752 (Korea, Republic of); Department and Research Institute of Dental Biomaterials and Bioengineering, College of Dentistry, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-752 (Korea, Republic of); Han, Jeon-Geon [Center for Advanced Plasma Surface Technology, Sungkyunkwan University, 300 Chunchun-dong, Jangan-gu, Suwon 440-746 (Korea, Republic of); Boonyawan, Dheerawan [Thailand Center of Excellence in Physics (ThEP), 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand); Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand)

    2013-10-15

    In this study, we focused on sericin hydrolysates, originating from silkworm used in serum-free human bone marrow-derived mesenchymal stem cells (hBM-MSCs) culture. We reported the effect of a covalent linkage between a bioactive protein molecule and polystyrene dish surface via a carbon intermediate layer which can slow down the release rate of protein compounds into the phosphate buffer saline (PBS) solution. Films of amorphous carbon (a-C) and functionalized-carbon were deposited on PS culture dish surfaces by using a DC magnetron sputtering system and RF PECVD system. We found that a-C based-films can increase the hydrophilicity and biocompatibility of polystyrene (PS) dishes, especially a-C films and a-C:N{sub 2} films showed good attachment of hBM-MSCs at 24 h. However, in the case of silica surface (a-C:SiO{sub x} films), the cells showed a ragged and unattached boundary resulting from the presence of surface silanol groups. For the UV–vis absorbance, all carbon modified-PS dishes showed a lower release rate of sericin molecules into PBS solution than PS control. This revealed that the functionalized carbon could be enhanced by specific binding properties with given molecules. The carbon-coated PS dishes grafting with sericin protein were used in a serum-free condition. We also found that hBM-MSCs have higher percentage of proliferated cells at day 7 for the modified dishes with carbon films and coated with sericin than the PS control coated with sericin. The physical film properties were measured by atomic force microscopy (AFM), scanning electron microscope (SEM) and contact angle measurement. The presence of -NH{sub 2} groups of sericin compounds on the PS dish was revealed by Fourier transform infrared spectroscopy (FTIR). The stability of covalent bonds of sericin molecules after washing out ungrafted sericin was confirmed by X-ray photoelectron spectroscopy (XPS).

  4. Nutritional composition of commonly consumed composite dishes from rural villages in Empangeni, KwaZulu-Natal, South Africa.

    Science.gov (United States)

    Spearing, K; Kolahdooz, F; Lukasewich, M; Mathe, N; Khamis, T; Sharma, S

    2013-06-01

    Accurate nutrient composition data for composite dishes unique to a population is essential for the development of a nutrient database and the calculation of dietary intake. The present study aimed to provide the nutritional composition of composite dishes frequently consumed in rural KwaZulu-Natal, South Africa. Commonly consumed composite dishes were identified using 24-h recalls collected from 79 randomly selected community members. Multiple recipes were collected for each reported dish. The mean nutritional composition of each dish was calculated per 100 g using the nutribase clinical nutrition manager (Cybersoft Inc., Phoenix, AZ, USA). A total of 79 recipes were collected for 16 commonly consumed dishes (seven meat-based, five starch-based and four legume/vegetable-based). 'Fried chicken' contained the most energy [1469 kJ (351 kcal)], protein (29.7 g), fat (23.7 g), cholesterol (123 mg) and niacin (8.4 mg). 'Fried beef' contained the most potassium (495 mg) and zinc (6.4 mg), whereas 'fish stew' had the most vitamin D (4.2 μg) and calcium (215 mg). 'Fried cabbage' and 'fried spinach' contained the largest percent energies from fat, at 79% and 76%, respectively. A traditional sweet bread, 'jeqe', made with fortified flour contributed significantly to iron (4.6 mg), niacin (4.5 μg) and folate (129 μg). The sodium content of dishes ranged from 88 to 679 mg per 100 g. The nutritional composition data for commonly consumed dishes in rural KwaZulu-Natal is presented. Although the dishes are good sources of protein, vitamins and minerals, they also contain substantial amounts of fat. This culturally appropriate information will enable the calculation of dietary intake and can be used to encourage the consumption of recipes rich in key nutrients. © 2012 The Authors Journal of Human Nutrition and Dietetics © 2012 The British Dietetic Association Ltd.

  5. Exergy Analysis of a Pilot Parabolic Solar Dish-Stirling System

    Directory of Open Access Journals (Sweden)

    Ehsan Gholamalizadeh

    2017-09-01

    Full Text Available Energy and exergy analyses were carried out for a pilot parabolic solar dish-Stirling System. The system was set up at a site at Kerman City, located in a sunny desert area of Iran. Variations in energy and exergy efficiency were considered during the daytime hours of the average day of each month in a year. A maximum collector energy efficiency and total energy efficiency of 54% and 12.2%, respectively, were predicted in July, while during the period between November and February the efficiency values were extremely low. The maximum collector exergy efficiency was 41.5% in July, while the maximum total exergy efficiency reached 13.2%. The values of energy losses as a percentage of the total losses of the main parts of the system were also reported. Results showed that the major energy and exergy losses occurred in the receiver. The second biggest portion of energy losses occurred in the Stirling engine, while the portion of exergy loss in the concentrator was higher compared to the Stirling engine. Finally, the performance of the Kerman pilot was compared to that of the EuroDish project.

  6. Design, simulation and optimization of a solar dish collector with spiral-coil thermal absorber

    Directory of Open Access Journals (Sweden)

    Pavlović Saša R.

    2016-01-01

    Full Text Available The efficient conversion of solar radiation into heat at high temperature levels requires the use of concentrating solar collectors. The goal of this paper is to present the optical and the thermal analysis of a parabolic dish concentrator with a spiral coil receiver. The parabolic dish reflector consists of 11 curvilinear trapezoidal reflective petals constructed by PMMA with silvered mirror layer and has a diameter of 3.8 m, while its focal distance is 2.26m. This collector is designed with commercial software SolidWorks and simulated, optically and thermally in its Flow Simulation Studio. The optical analysis proved that the ideal position of the absorber is at 2.1m from the reflector in order to maximize the optical efficiency and to create a relative uniform heat flux over the absorber. In thermal part of the analysis, the energetic efficiency was calculated approximately 65%, while the exergetic efficiency is varied from 4% to 15% according to the water inlet temperature. Moreover, other important parameters as the heat flux and temperature distribution over the absorber are presented. The pressure drop of the absorber coil is calculated at 0.07bar, an acceptable value.

  7. Embryo density may affect embryo quality during in vitro culture in a microwell group culture dish.

    Science.gov (United States)

    Lehner, Adam; Kaszas, Zita; Murber, Akos; Rigo, Janos; Urbancsek, Janos; Fancsovits, Peter

    2017-08-01

    Culturing embryos in groups is a common practice in mammalian embryology. Since the introduction of different microwell dishes, it is possible to identify oocytes or embryos individually. As embryo density (embryo-to-volume ratio) may affect the development and viability of the embryos, the purpose of this study was to assess the effect of different embryo densities on embryo quality. Data of 1337 embryos from 228 in vitro fertilization treatment cycles were retrospectively analyzed. Embryos were cultured in a 25 μl microdrop in a microwell group culture dish containing 9 microwells. Three density groups were defined: Group 1 with 2-4 (6.3-12.5 μl/embryo), Group 2 with 5-6 (4.2-5.0 μl/embryo), and Group 3 with 7-9 (2.8-3.6 μl/embryo) embryos. Proportion of good quality embryos was higher in Group 2 on both days (D2: 18.9 vs. 31.5 vs. 24.7%; p Culturing 5-6 embryos together in a culture volume of 25 μl may benefit embryo quality. As low egg number, position, and distance of the embryos may influence embryo quality, results should be interpreted with caution.

  8. Analysis of solar water heater with parabolic dish concentrator and conical absorber

    Science.gov (United States)

    Rajamohan, G.; Kumar, P.; Anwar, M.; Mohanraj, T.

    2017-06-01

    This research focuses on developing novel technique for a solar water heating system. The novel solar system comprises a parabolic dish concentrator, conical absorber and water heater. In this system, the conical absorber tube directly absorbs solar radiation from the sun and the parabolic dish concentrator reflects the solar radiations towards the conical absorber tube from all directions, therefore both radiations would significantly improve the thermal collector efficiency. The working fluid water is stored at the bottom of the absorber tubes. The absorber tubes get heated and increases the temperature of the working fluid inside of the absorber tube and causes the working fluid to partially evaporate. The partially vaporized working fluid moves in the upward direction due to buoyancy effect and enters the heat exchanger. When fresh water passes through the heat exchanger, temperature of the vapour decreases through heat exchange. This leads to condensation of the vapour and forms liquid phase. The working fluid returns to the bottom of the collector absorber tube by gravity. Hence, this will continue as a cyclic process inside the system. The proposed investigation shows an improvement of collector efficiency, enhanced heat transfer and a quality water heating system.

  9. Operational data and thermodynamic modeling of a Stirling-dish demonstration installation in desert conditions

    Science.gov (United States)

    Nilsson, Martin; Jamot, Jakob; Malm, Tommy

    2017-06-01

    To field test its Stirling-dish unit, Cleanergy AB of Sweden in Q1 2015 built a ten unit demo park in Dubai. The first STE (Solar Thermal Energy) generation of its Stirling genset, the C11S, had at its core an 11 kWel Stirling engine/generator combination. The genset was mated with a parabolic concentrator developed for the genset by a supplier. Local weather conditions in Dubai provide opportunities to test performance in an environment with high insolation and high ambient temperature. In addition, the conditions in Dubai are windy, salty, humid and dusty, historically challenging for solar technologies [1]. In Q1 2016 one of the C11S Stirling-dish units was replaced by the first prototype of Cleanergy's second generation Stirling genset, the Sunbox, and an in-house developed parabolic concentrator. Operational data from field testing during the spring of 2016 are presented and discussed and show the large performance improvement achieved with the Sunbox unit.

  10. Validation of a Dish-Based Semiquantitative Food Questionnaire in Rural Bangladesh

    Directory of Open Access Journals (Sweden)

    Pi-I. D. Lin

    2017-01-01

    Full Text Available A locally validated tool was needed to evaluate long-term dietary intake in rural Bangladesh. We assessed the validity of a 42-item dish-based semi-quantitative food frequency questionnaire (FFQ using two 3-day food diaries (FDs. We selected a random subset of 47 families (190 participants from a longitudinal arsenic biomonitoring study in Bangladesh to administer the FFQ. Two 3-day FDs were completed by the female head of the households and we used an adult male equivalent method to estimate the FD for the other participants. Food and nutrient intakes measured by FFQ and FD were compared using Pearson’s and Spearman’s correlation, paired t-test, percent difference, cross-classification, weighted Kappa, and Bland–Altman analysis. Results showed good validity for total energy intake (paired t-test, p < 0.05; percent difference <10%, with no presence of proportional bias (Bland–Altman correlation, p > 0.05. After energy-adjustment and de-attenuation for within-person variation, macronutrient intakes had excellent correlations ranging from 0.55 to 0.70. Validity for micronutrients was mixed. High intraclass correlation coefficients (ICCs were found for most nutrients between the two seasons, except vitamin A. This dish-based FFQ provided adequate validity to assess and rank long-term dietary intake in rural Bangladesh for most food groups and nutrients, and should be useful for studying dietary-disease relationships.

  11. Primary Beam and Dish Surface Characterization at the Allen Telescope Array by Radio Holography

    Science.gov (United States)

    Harp, G. R.; Ackermann, R. F.; Nadler, Z. J.; Blair, Samantha K.; Davis, M. M.; Wright, M. C. H.; Forster, J. R.; Deboer, D. R.; Welch, W. J.; Atkinson, Shannon; Backer, D. C.; Backus, P. R.; Barott, William; Bauermeister, Amber; Blitz, Leo; Bock, D. C.-J.; Bower, Geoffrey C.; Bradford, Tucker; Cheng, Calvin; Croft, Steve; Dexter, Matt; Dreher, John; Engargiola, Greg; Fields, E. D.; Heiles, Carl; Helfer, Tamara; Jordan, Jane; Jorgensen, Susan; Kilsdonk, Tom; Gutierrez-Kraybill, Colby; Keating, Garrett; Law, Casey; Lugten, John; MacMahon, D. H. E.; McMahon, Peter; Milgrome, Oren; Siemion, Andrew; Smolek, Ken; Thornton, Douglas; Pierson, Tom; Randall, Karen; Ross, John; Shostak, Seth; Tarter, J. C.; Urry, Lynn; Werthimer, Dan; Williams, Peter K. G.; Whysong, David

    2011-06-01

    The Allen Telescope Array (ATA) is a cm-wave interferometer in California, comprising 42 antenna elements with 6-m diameter dishes. We characterize the antenna optical accuracy using two-antenna interferometry and radio holography. The distortion of each telescope relative to the average is small, with RMS differences of 1% of beam peak value. Holography provides images of dish illumination, characterizing as-built mirror surfaces. Maximal distortions across ~ 2 meter lengths appear to result from mounting stresses or solar radiation. Experimental RMS errors are 0.7 mm at night and 3 mm under worst-case solar illumination. For frequencies 4, 10, and 15 GHz, the nighttime values indicate sensitivity losses of 1, 10 and 20%, respectively. ATA's wide-bandwidth receiver permits observations over a continuous range 0.5-11.2 GHz. We probe the antenna optical gain and beam pattern stability as a function of focus position and observation frequency, concluding that ATA can produce high fidelity images over a decade of simultaneous observation frequencies. We quantify solar heating effects on antenna sensitivity and pointing accuracy. We find that during the day, observations >=5 GHz will suffer some sensitivity loss and it may be necessary to make antenna pointing corrections on a 1-2 hourly basis.

  12. Effect of Tracking Error of Double-Axis Tracking Device on the Optical Performance of Solar Dish Concentrator

    Directory of Open Access Journals (Sweden)

    Jian Yan

    2018-01-01

    Full Text Available In this paper, a flux distribution model of the focal plane in dish concentrator system has been established based on ray tracking method. This model was adopted for researching the influence of the mirror slope error, solar direct normal irradiance, and tracking error of elevation-azimuth tracking device (EATD on the focal spot characteristics (i.e., flux distribution, geometrical shape, centroid position, and intercept factor. The tracking error transmission law of the EATD transferred to dish concentrator was also studied. The results show that the azimuth tracking error of the concentrator decreases with the increase of the concentrator elevation angle and it decreases to 0 mrad when the elevation angle is 90°. The centroid position of focal spot along x-axis and y-axis has linear relationship with azimuth and elevation tracking error of EATD, respectively, which could be used to evaluate and calibrate the tracking error of the dish concentrator. Finally, the transmission law of the EATD azimuth tracking error in solar heliostats is analyzed, and a dish concentrator using a spin-elevation tracking device is proposed, which can reduce the effect of spin tracking error on the dish concentrator. This work could provide fundamental for manufacturing precision allocation of tracking devices and developing a new type of tracking device.

  13. Performance tests and efficiency analysis of Solar Invictus 53S - A parabolic dish solar collector for direct steam generation

    Science.gov (United States)

    Jamil, Umer; Ali, Wajahat

    2016-05-01

    This paper presents the results of performance tests conducted on Solar Invictus 53S `system'; an economically effective solar steam generation solution designed and developed by ZED Solar Ltd. The system consists of a dual axis tracking parabolic solar dish and bespoke cavity type receiver, which works as a Once Through Solar Steam Generator `OTSSG' mounted at the focal point of the dish. The overall performance and efficiency of the system depends primarily on the optical efficiency of the solar dish and thermal efficiency of the OTSSG. Optical testing performed include `on sun' tests using CCD camera images and `burn plate' testing to evaluate the sunspot for size and quality. The intercept factor was calculated using a colour look-back method to determine the percentage of solar rays focused into the receiver. Solar dish tracking stability tests were carried out at different times of day to account for varying dish elevation angles and positions, movement of the sunspot centroid was recorded and logged using a CCD camera. Finally the overall performance and net solar to steam efficiency of the system was calculated by experimentally measuring the output steam parameters at varying Direct Normal Insolation (DNI) levels at ZED Solar's test facility in Lahore, Pakistan. Thermal losses from OTSSG were calculated using the known optical efficiency and measured changes in output steam enthalpy.

  14. A review of test results on solar thermal power modules with dish-mounted Stirling and Brayton cycle engines

    Science.gov (United States)

    Jaffe, Leonard D.

    1988-01-01

    This paper presents results of development tests of various solar thermal parabolic dish modules and assemblies that used dish-mounted Brayton or Stirling cycle engines for production of electric power. These tests indicate that early modules achieve net efficiencies up to 29 percent in converting sunlight to electricity, as delivered to the grid. Various equipment deficiencies were observed and a number of malfunctions occurred. The performance measurements, as well as the malfunctions and other test experience, provided information that should be of value in developing systems with improved performance and reduced maintenance.

  15. A review of test results on solar thermal power modules with dish-mounted Stirling and Brayton cycle engines

    Science.gov (United States)

    Jaffe, Leonard D.

    1988-11-01

    This paper presents results of development tests of various solar thermal parabolic dish modules and assemblies that used dish-mounted Brayton or Stirling cycle engines for production of electric power. These tests indicate that early modules achieve net efficiencies up to 29 percent in converting sunlight to electricity, as delivered to the grid. Various equipment deficiencies were observed and a number of malfunctions occurred. The performance measurements, as well as the malfunctions and other test experience, provided information that should be of value in developing systems with improved performance and reduced maintenance.

  16. Automatic Evaluation of Colonies Growth rate of Yeasts incubated in Petri dishes using Mobile Platform

    Directory of Open Access Journals (Sweden)

    Alecsander Pereira Martins

    2015-10-01

    Full Text Available This paper proposes an automatic method based on computer vision implemented in mobile platform capable of monitoring the growth of microbial colonies incubated in Petri dishes. The developed optimized image processing algorithm performs this task without human intervention from images of colonies of the microorganism in different evolution phases. The contribution of this paper is the development of a fast and robust mobile tool to assist bioprocess experts in monitoring the growth of colonies without using the conventional error prone evaluation techniques. The obtained results successfully demonstrated dimensional alterations in colonies in a faster and more precise fashion when compared with the conventional method, with the additional advantage of versatility in producing reliable estimation of the growth rates with higher statistical significance.

  17. Dispersed solar thermal generation employing parabolic dish-electric transport with field modulated generator systems

    Science.gov (United States)

    Ramakumar, R.; Bahrami, K.

    1981-01-01

    This paper discusses the application of field modulated generator systems (FMGS) to dispersed solar-thermal-electric generation from a parabolic dish field with electric transport. Each solar generation unit is rated at 15 kWe and the power generated by an array of such units is electrically collected for insertion into an existing utility grid. Such an approach appears to be most suitable when the heat engine rotational speeds are high (greater than 6000 r/min) and, in particular, if they are operated in the variable speed mode and if utility-grade a.c. is required for direct insertion into the grid without an intermediate electric energy storage and reconversion system. Predictions of overall efficiencies based on conservative efficiency figures for the FMGS are in the range of 25 per cent and should be encouraging to those involved in the development of cost-effective dispersed solar thermal power systems.

  18. Optical characterization of nonimaging dish concentrator for the application of dense-array concentrator photovoltaic system.

    Science.gov (United States)

    Tan, Ming-Hui; Chong, Kok-Keong; Wong, Chee-Woon

    2014-01-20

    Optimization of the design of a nonimaging dish concentrator (NIDC) for a dense-array concentrator photovoltaic system is presented. A new algorithm has been developed to determine configuration of facet mirrors in a NIDC. Analytical formulas were derived to analyze the optical performance of a NIDC and then compared with a simulated result obtained from a numerical method. Comprehensive analysis of optical performance via analytical method has been carried out based on facet dimension and focal distance of the concentrator with a total reflective area of 120 m2. The result shows that a facet dimension of 49.8 cm, focal distance of 8 m, and solar concentration ratio of 411.8 suns is the most optimized design for the lowest cost-per-output power, which is US$1.93 per watt.

  19. Modelling resource consumption for laundry and dish treatment in individual households for various consumer segments

    Energy Technology Data Exchange (ETDEWEB)

    Stamminger, R. [Institute for Agricultural Engineering, Household and Appliance Technology Section, University of Bonn, Nussallee 5, 53115 Bonn (Germany)

    2011-11-15

    Recent research allocates up to 80% of environmental impact in energy and CO2 terms to direct and indirect consumer activities. Various models discussed how this impact can be assigned to specific lifestyles, production and consumption systems, and psychological motives in order to be able to predict and influence these effects. In this work, another approach is followed by showing on the example of laundry and dish washing how well-known factors of the technical status, consumer practices and demographic data allow building up a model to predict the energy and water consumption for these processes. The results show a variation of a factor of 5 between a more sustainable and a more careless behaviour and allow thus to identify levers to influence it. As results can also be easily transformed into monetary values, this may allow influencing the consumer via this channel as he/she can easily understand what may need to be changed.

  20. Thermal modeling of a pressurized air cavity receiver for solar dish Stirling system

    Science.gov (United States)

    Zou, Chongzhe; Zhang, Yanping; Falcoz, Quentin; Neveu, Pierre; Li, Jianlan; Zhang, Cheng

    2017-06-01

    A solar cavity receiver model for the dish collector system is designed in response to growing demand of renewable energy. In the present research field, no investigations into the geometric parameters of a cavity receiver have been performed. The cylindrical receiver in this study is composed of an enclosed bottom at the back, an aperture at the front, a helical pipe inside the cavity and an insulation layer on the external surface of the cavity. The influence of several critical receiver parameters on the thermal efficiency is analyzed in this paper: cavity inner diameter and cavity length. The thermal model in this paper is solved considering the cavity dimensions as variables. Implementing the model into EES, each parameter influence is separately investigated, and a preliminary optimization method is proposed.

  1. Large-area, high-intensity PV arrays for systems using dish concentrating optics

    Energy Technology Data Exchange (ETDEWEB)

    Ward, J.S.; Duda, A.; Zweibel, K.; Coutts, T.J. [National Renewable Energy Lab., Golden, CO (United States)

    1998-09-01

    In this paper, the authors report on efforts to fabricate monolithic interconnected modules (MIMs) using III-V semiconductors with bandgaps appropriate for the terrestrial solar spectrum. The small size of the component cells comprising the MIM allows for operation at extremely high flux densities and relaxes the requirement for a small spot size to be generated by the optics. This makes possible a PV option for the large dish concentrator systems that have been developed by the solar thermal community for use with Stirling engines. Additionally, the highly effective back-surface reflector integrated into the MIM design is an effective tool for thermal management of the array. Development of this technology would radically alter the projections for PV manufacturing capacity because of the potential for extremely high power generation per unit area of semiconductor material.

  2. Flexible Sheet-Type Sensor for Noninvasive Measurement of Cellular Oxygen Metabolism on a Culture Dish.

    Directory of Open Access Journals (Sweden)

    Mari Kojima

    Full Text Available A novel flexible sensor was developed for the noninvasive oxygen metabolism measurement of cultivated cells and tissues. This device is composed of a transparent double-layered polymer sheet of ethylene-vinyl alcohol (EVOH and poly(dimethylsiloxane (PDMS having an array of microhole structures of 90 μm diameter and 50 μm depth on its surface. All the microhole structures were equipped with a 1-μm-thick optical chemical sensing layer of platinum porphyrin-fluoropolymer on their bottom. The three-dimensional microstructures of the sensor were fabricated by a newly developed simple and low-cost production method named self-aligned hot embossing. The device was designed to be attached slightly above the cells cultivated on a dish to form a temporarily closed microspace over the target cells during measurement. Since the change in oxygen concentration is relatively fast in the microcompartmentalized culture medium, a rapid evaluation of the oxygen consumption rate is possible by measuring the phosphorescence lifetime of the platinum porphyrin-fluoropolymer. The combined use of the device and an automated optical measurement system enabled the high-throughput sensing of cellular oxygen consumption (100 points/min. We monitored the oxygen metabolism of the human breast cancer cell line MCF7 on a Petri dish and evaluated the oxygen consumption rate to be 0.72 ± 0.12 fmol/min/cell. Furthermore, to demonstrate the utility of the developed sensing system, we demonstrated the mapping of the oxygen consumption rate of rat brain slices and succeeded in visualizing a clear difference among the layer structures of the hippocampus, i.e., the cornu ammonis (CA1 and CA3 and dentate gyrus (DG.

  3. On-sun performance of an improved dish-based HCPV system

    Science.gov (United States)

    Stalcup, Thomas; Angel, Roger P.; Coughenour, Blake; Wheelwright, Brian; Connors, Tom; Davison, Warren; Lesser, David; Elliott, Justin; Schaefer, John

    2012-10-01

    The University of Arizona has developed a new dish-based High Concentration Photovoltaic (HCPV) system which is in the process of being commercialized by REhnu, Inc. The basic unit uses a paraboloidal glass reflector 3.1 m x 3.1 m square to bring sunlight to a high power point focus at a concentration of ~20,000x. A unique optical system at the focus reformats the concentrated sunlight so as to uniformly illuminate 36 triple junction cells at 1200x geometric concentration1. The relay optics and cells are integrated with an active cooling system in a self-contained Power Conversion Unit (PCU) suspended above the dish reflector. Only electrical connections are made to the PCU as the active cooling system within is completely sealed. Eight of these reflector/PCU units can be mounted on a single two axis tracking structure2. Our 1st generation prototype reflector/PCU unit consistently generated 2.2 kW of power normalized to 1kW/m2 DNI in over 200 hours of on-sun testing in 20113. Here, we present on-sun performance results for our 2nd generation prototype reflector/PCU unit, which has been in operation since June 2012. This improved system consistently generates 2.7 kW of power normalized to 1kW/m2 DNI and has logged over 100 hours of on-sun testing. This system is currently operating at28% DC net system efficiency with an operating cell temperature of only 20°C above ambient. Having proven this system concept, work on our 3rd generation prototype is underway with a focus on manufacturability, lower cost, and DC efficiency target of 32% or better.

  4. Indonesian consumers' perception of tempe in a restaurant setting traditional and modern tempe version in traditional and innovative dishes

    DEFF Research Database (Denmark)

    Fibri, Dwi Larasatie Nur; Frøst, Michael Bom

    by introducing local bean tempe in fine dining. The objective of this research was to study how different raw materials, dishes and gastronomic style affect the perception and appreciation of the food. A restaurant experiment (n=208) was carried out. Three different types of tempe (local soybean tempe, imported...

  5. Recipes and nutritional value of dishes prepared from green-leafy vegetables in an urban district of Antananarivo (Madagascar).

    Science.gov (United States)

    Randrianatoandro, Verohanitra Annie; Avallone, Sylvie; Picq, Christian; Ralison, Charlotte; Trèche, Serge

    2010-06-01

    The recipes of 50 multi-ingredient dishes consumed by the population in an urban district were noted down. The nutritional value was determined as well as the cook value of the dishes in order to evaluate the severity of the thermal treatment. The recipes were simple and involved steps such as boiling, mixing, and cutting. Fibre contents were rather low except when the leaf stems were included. All the dishes had very high beta-carotene content (15.8-25.0 mg/100 g dry matter) and retinol activity equivalent (RAE) (1.3-2.3 mg RAE/100 g dry matter) because of the high proportion of fresh leafy vegetables (from 41.2% to 58.8% of the total dry matter of the ingredients). When meat was added to the preparation, the micronutrient content (iron, zinc, and retinol) was not increased significantly. In three dishes, a positive correlation was found between the thermal treatment severity and the 13-cis-beta-carotene amount.

  6. Isotopic examination of links between diet, social differentiation, and DISH at the post-medieval Carmelite Friary of Aalst, Belgium.

    Science.gov (United States)

    Quintelier, Kim; Ervynck, Anton; Müldner, Gundula; Van Neer, Wim; Richards, Michael P; Fuller, Benjamin T

    2014-02-01

    Stable isotope ratios (δ(13) C and δ(15) N) were measured in human burials from the post-medieval (16th-18th c. AD) Carmelite friary burial grounds at Aalst, a town in Flanders, Belgium. Dietary patterns of 39 adult individuals were analyzed, from a mixed monastic and lay population buried in three different locations, reflecting groups with differing social status. The data show significant variation in the consumption of perhaps meat, but certainly also marine protein between females and males. This result represents a remarkable continuity with medieval dietary patterns, suggesting that the social and economic changes of the early modern period had a limited effect on everyday life. When both sexes were examined together, individuals buried in the cloister garth consumed significantly less marine protein compared to people buried in the church, likely reflecting social stratification. No statistical differences were observed between isotopic values from the church and the cloister alley, suggesting a similarly diverse diet of the monastic part of the buried population and that of the richer lay population. Finally, the hypothesis that diffuse idiopathic skeletal hyperostosis (DISH) is linked to a diet rich in animal protein was tested. No systematic or statistically significant differences between pathological and non-pathological bones from the same individuals affected with DISH were observed, and no statistical differences were found between individuals with DISH and individuals without DISH. Copyright © 2013 Wiley Periodicals, Inc.

  7. Phytate/calcium molar ratio does not predict accessibility of calcium in ready-to-eat dishes.

    Science.gov (United States)

    Erba, Daniela; Manini, Federica; Meroni, Erika; Casiraghi, Maria C

    2017-08-01

    Phytic acid (PA), a naturally occurring compound of plant food, is generally considered to affect mineral bioavailability. The aim of this study was to investigate the reliability of the PA/calcium molar ratio as a predictive factor of calcium accessibility in composed dishes and their ingredients. Dishes were chosen whose ingredients were rich in Ca (milk or cheese) or in PA (whole-wheat cereals) in order to consider a range of PA/Ca ratios (from 0 to 2.4) and measure Ca solubility using an in vitro approach. The amounts of soluble Ca in composed dishes were consistent with the sum of soluble Ca from ingredients (three out of five meals) or higher. Among whole-wheat products, bread showed higher Ca accessibility (71%, PA/Ca = 1.1) than biscuits (23%, PA/Ca = 0.9) and pasta (15%, PA/Ca = 1.5), and among Ca-rich ingredients, semi-skimmed milk displayed higher Ca accessibility (64%) than sliced cheese (50%) and Parmesan (38%). No significant correlation between the PA/Ca ratio and Ca accessibility was found (P = 0.077). The reliability of the PA/Ca ratio for predicting the availability of calcium in composed dishes is unsatisfactory; data emphasized the importance of the overall food matrix influence on mineral accessibility. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  8. Risk factors for contamination of ready-to-eat street-vended poultry dishes in Dakar, Senegal.

    Science.gov (United States)

    Cardinale, E; Perrier Gros-Claude, J D; Tall, F; Guèye, E F; Salvat, G

    2005-08-25

    Our objective was to investigate the Salmonella and Campylobacter contamination of traditional ready-to-eat street-vended poultry dishes and to assess the association of some restaurant characteristics and cooking practices with the contamination of these meals. One hundred and forty-eight street-restaurants were studied from January 2003 to April 2004 in Dakar. A questionnaire was submitted to the managers, and samples of ready-to-eat poultry dishes were taken. Salmonella spp. was isolated in 20.1% of the 148 street-restaurants studied and in 10.1% samples of poultry dishes. The most prevalent serovars isolated were Salmonella hadar, Salmonella enteritidis and Salmonella brancaster. Campylobacter jejuni was detected in only 3 restaurants and 3 poultry dishes. Not peeling and not cleaning vegetables and other ingredients during meal preparation (OR=3.58), dirty clothing for restaurant employees (OR=4.65), reheating previously cooked foods (OR=5.2), and no kitchen and utensils disinfection (OR=3.47) were associated with an increasing risk of Salmonella contamination. Adequate cooking procedures decreased the risk of Salmonella contamination (OR=0.15).

  9. Observing the Sun with the Atacama Large Millimeter/submillimeter Array (ALMA): Fast-Scan Single-Dish Mapping

    Science.gov (United States)

    White, S. M.; Iwai, K.; Phillips, N. M.; Hills, R. E.; Hirota, A.; Yagoubov, P.; Siringo, G.; Shimojo, M.; Bastian, T. S.; Hales, A. S.; Sawada, T.; Asayama, S.; Sugimoto, M.; Marson, R. G.; Kawasaki, W.; Muller, E.; Nakazato, T.; Sugimoto, K.; Brajša, R.; Skokić, I.; Bárta, M.; Kim, S.; Remijan, A. J.; de Gregorio, I.; Corder, S. A.; Hudson, H. S.; Loukitcheva, M.; Chen, B.; De Pontieu, B.; Fleishmann, G. D.; Gary, D. E.; Kobelski, A.; Wedemeyer, S.; Yan, Y.

    2017-07-01

    The Atacama Large Millimeter/submillimeter Array (ALMA) radio telescope has commenced science observations of the Sun starting in late 2016. Since the Sun is much larger than the field of view of individual ALMA dishes, the ALMA interferometer is unable to measure the background level of solar emission when observing the solar disk. The absolute temperature scale is a critical measurement for much of ALMA solar science, including the understanding of energy transfer through the solar atmosphere, the properties of prominences, and the study of shock heating in the chromosphere. In order to provide an absolute temperature scale, ALMA solar observing will take advantage of the remarkable fast-scanning capabilities of the ALMA 12 m dishes to make single-dish maps of the full Sun. This article reports on the results of an extensive commissioning effort to optimize the mapping procedure, and it describes the nature of the resulting data. Amplitude calibration is discussed in detail: a path that uses the two loads in the ALMA calibration system as well as sky measurements is described and applied to commissioning data. Inspection of a large number of single-dish datasets shows significant variation in the resulting temperatures, and based on the temperature distributions, we derive quiet-Sun values at disk center of 7300 K at λ = 3 mm and 5900 K at λ = 1.3 mm. These values have statistical uncertainties of about 100 K, but systematic uncertainties in the temperature scale that may be significantly larger. Example images are presented from two periods with very different levels of solar activity. At a resolution of about 25'', the 1.3 mm wavelength images show temperatures on the disk that vary over about a 2000 K range. Active regions and plages are among the hotter features, while a large sunspot umbra shows up as a depression, and filament channels are relatively cool. Prominences above the solar limb are a common feature of the single-dish images.

  10. Food Safety: Recommendations for Determining Doneness in Consumer Egg Dish Recipes and Measurement of Endpoint Temperatures When Recipes Are Followed

    Directory of Open Access Journals (Sweden)

    Sandria Godwin

    2016-06-01

    Full Text Available Many consumers do not follow recommended food safety practices for cooking egg dishes, such as pies, quiches, and casseroles, potentially leading to foodborne illnesses such as Salmonellosis. The United States Department of Agriculture (USDA recommends cooking egg mixtures until the center reaches 71 °C (160 °F. The objectives of this study were to determine what endpoint temperature information consumers receive from egg dish recipes, and if recipes would lead to safe temperatures when followed. Egg dish recipes (n = 226 from 65 websites, 50 cookbooks, and nine magazine titles (multiple issues of each were analyzed. Time was the most frequently used indicator, given in 92% of the recipes, with 15% using only time. Other indicators included: set (89, browned (76, clean toothpick/knife (60, puffed (27, and jiggled (13. Only two recipes indicated final endpoint temperatures. Three recipes (a pie, a quiche, and an egg casserole were chosen and prepared in triplicate to see if they would reach recommended temperatures. The pie and quiche were still liquid at 71 °C, and were well over the recommended temperature when cooked according to instructions, but the egg casserole was not consistently above 71 °C, when the recipe instructions indicated it was done and the center was light brown and “jiggled” This research indicates that consumers are not receiving information on endpoint temperatures in egg recipes, but the likelihood of foodborne illness is low since most dishes probably be cooked past the recommended temperature before the consumer considers them done unless there are many inclusions that may absorb liquid and reduce the appearance of liquid in the dish.

  11. Food Safety: Recommendations for Determining Doneness in Consumer Egg Dish Recipes and Measurement of Endpoint Temperatures When Recipes Are Followed

    Science.gov (United States)

    Godwin, Sandria; Maughan, Curtis; Chambers, Edgar

    2016-01-01

    Many consumers do not follow recommended food safety practices for cooking egg dishes, such as pies, quiches, and casseroles, potentially leading to foodborne illnesses such as Salmonellosis. The United States Department of Agriculture (USDA) recommends cooking egg mixtures until the center reaches 71 °C (160 °F). The objectives of this study were to determine what endpoint temperature information consumers receive from egg dish recipes, and if recipes would lead to safe temperatures when followed. Egg dish recipes (n = 226) from 65 websites, 50 cookbooks, and nine magazine titles (multiple issues of each) were analyzed. Time was the most frequently used indicator, given in 92% of the recipes, with 15% using only time. Other indicators included: set (89), browned (76), clean toothpick/knife (60), puffed (27), and jiggled (13). Only two recipes indicated final endpoint temperatures. Three recipes (a pie, a quiche, and an egg casserole) were chosen and prepared in triplicate to see if they would reach recommended temperatures. The pie and quiche were still liquid at 71 °C, and were well over the recommended temperature when cooked according to instructions, but the egg casserole was not consistently above 71 °C, when the recipe instructions indicated it was done and the center was light brown and “jiggled” This research indicates that consumers are not receiving information on endpoint temperatures in egg recipes, but the likelihood of foodborne illness is low since most dishes probably be cooked past the recommended temperature before the consumer considers them done unless there are many inclusions that may absorb liquid and reduce the appearance of liquid in the dish. PMID:28231140

  12. Food Safety: Recommendations for Determining Doneness in Consumer Egg Dish Recipes and Measurement of Endpoint Temperatures When Recipes Are Followed.

    Science.gov (United States)

    Godwin, Sandria; Maughan, Curtis; Chambers, Edgar

    2016-06-23

    Many consumers do not follow recommended food safety practices for cooking egg dishes, such as pies, quiches, and casseroles, potentially leading to foodborne illnesses such as Salmonellosis. The United States Department of Agriculture (USDA) recommends cooking egg mixtures until the center reaches 71 °C (160 °F). The objectives of this study were to determine what endpoint temperature information consumers receive from egg dish recipes, and if recipes would lead to safe temperatures when followed. Egg dish recipes ( n = 226) from 65 websites, 50 cookbooks, and nine magazine titles (multiple issues of each) were analyzed. Time was the most frequently used indicator, given in 92% of the recipes, with 15% using only time. Other indicators included: set (89), browned (76), clean toothpick/knife (60), puffed (27), and jiggled (13). Only two recipes indicated final endpoint temperatures. Three recipes (a pie, a quiche, and an egg casserole) were chosen and prepared in triplicate to see if they would reach recommended temperatures. The pie and quiche were still liquid at 71 °C, and were well over the recommended temperature when cooked according to instructions, but the egg casserole was not consistently above 71 °C, when the recipe instructions indicated it was done and the center was light brown and "jiggled" This research indicates that consumers are not receiving information on endpoint temperatures in egg recipes, but the likelihood of foodborne illness is low since most dishes probably be cooked past the recommended temperature before the consumer considers them done unless there are many inclusions that may absorb liquid and reduce the appearance of liquid in the dish.

  13. Differences in nutrient and energy content of commonly-consumed dishes prepared in restaurants vs. at home in Hunan province, China

    Science.gov (United States)

    Jia, Xiaofang; Liu, Jiawu; Chen, Bo; Jin, Donghui; Fu, Zhongxi; Liu, Huilin; Du, Shufa; Popkin, Barry M.; Mendez, Michelle A.

    2017-01-01

    Objective Eating away from home is associated with poor diet quality, in part due to less healthy food choices and larger portions. However, few studies take into account the potential additional contribution of differences in food composition between restaurant- and home-prepared dishes. This study aimed to investigate differences in nutrients of dishes prepared in restaurants vs. at home. Design Eight commonly consumed dishes were collected in 20 of each of the following types of locations: small and large restaurants, and urban and rural households. In addition, two fast-food items were collected from 10 KFC’s, McDonald’s, and food stalls. Five samples per dish were randomly pooled from every location. Nutrients were analyzed and energy was calculated in composite samples. Differences in nutrients of dishes by preparation location were determined. Setting Urban and rural. Subjects Sodium, potassium, protein, total fat, fatty acids, carbohydrate, and energy in dishes. Results On average, both the absolute and relative fat content, saturated fatty acid (SFA) and sodium/potassium ratio were higher in dishes prepared in restaurants than households (Prestaurants (P restaurant preparation was consistently negatively associated with protein and positively associated with the percentage energy from fat in all dishes. Moreover, restaurant preparation also positively influenced the SFA content in dishes, except at the highest quantiles. Conclusions These findings suggest that compared to home preparation, dishes prepared in restaurants in China may differ in concentrations of total fat, SFA, protein, and sodium/potassium ratio, which may further contribute, beyond food choices, to less healthy nutrient intake linked to eating away from home. PMID:29306339

  14. Open-dish incubator for live cell imaging with an inverted microscope.

    Science.gov (United States)

    Heidemann, Steven R; Lamoureux, Phillip; Ngo, Kha; Reynolds, Matthew; Buxbaum, Robert E

    2003-10-01

    Here we describe the design and fabrication of an inexpensive cell culture incubator for the stage of an inverted light microscope for use in live cell imaging. This device maintains the temperature of the cell culture at 37 degrees C with great stability and, after reaching equilibrium, provides focal stability of an image for 20-25 min with oil-immersion lenses. We describe two versions of the incubator: one for use with standard 60-mm plastic culture dishes, and the other version for imaging of cells on glass coverslips. Either can be made for less than $400. Most components are widely available commercially, and it requires only simple wiring and 3 h to assemble. Although the device is generally useful for live cell imaging on an inverted microscope, it is particularly suitable for work in which instruments are introduced into the culture, such as electrophysiology or micromanipulation. The design is based on the principle that control performance is limited by the lag time between detection and response. The key element of the design is a heated, temperature-controlled aluminum ring serving as a mini-incubator surrounding the culture vessel. For this reason, we call our design a "ringcubator."

  15. A PDMS Device Coupled with Culture Dish for In Vitro Cell Migration Assay.

    Science.gov (United States)

    Lv, Xiaoqing; Geng, Zhaoxin; Fan, Zhiyuan; Wang, Shicai; Pei, WeiHua; Chen, Hongda

    2018-04-30

    Cell migration and invasion are important factors during tumor progression and metastasis. Wound-healing assay and the Boyden chamber assay are efficient tools to investigate tumor development because both of them could be applied to measure cell migration rate. Therefore, a simple and integrated polydimethylsiloxane (PDMS) device was developed for cell migration assay, which could perform quantitative evaluation of cell migration behaviors, especially for the wound-healing assay. The integrated device was composed of three units, which included cell culture dish, PDMS chamber, and wound generation mold. The PDMS chamber was integrated with cell culture chamber and could perform six experiments under different conditions of stimuli simultaneously. To verify the function of this device, it was utilized to explore the tumor cell migration behaviors under different concentrations of fetal bovine serum (FBS) and transforming growth factor (TGF-β) at different time points. This device has the unique capability to create the "wound" area in parallel during cell migration assay and provides a simple and efficient platform for investigating cell migration assay in biomedical application.

  16. Metabolic Profiling Directly from the Petri Dish Using Nanospray Desorption Electrospray Ionization Imaging Mass Spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Watrous, Jeramie D.; Roach, Patrick J.; Heath, Brandi S.; Alexandrov, Theodore; Laskin, Julia; Dorrestein, Pieter C.

    2013-11-05

    Understanding molecular interaction pathways in complex biological systems constitutes a treasure trove of knowledge that might facilitate the specific, chemical manipulation of the countless microbiological systems that occur throughout our world. However, there is a lack of methodologies that allow the direct investigation of chemical gradients and interactions in living biological systems, in real time. Here, we report the use of nanospray desorption electrospray ionization (nanoDESI) imaging mass spectrometry for in vivo metabolic profiling of living bacterial colonies directly from the Petri dish with absolutely no sample preparation needed. Using this technique, we investigated single colonies of Shewanella oneidensis MR-1, Bacillus subtilis 3610, and Streptomyces coelicolor A3(2) as well as a mixed biofilm of S. oneidensis MR-1 and B. subtilis 3610. Data from B. subtilis 3610 and S. coelicolor A3(2) provided a means of validation for the method while data from S. oneidensis MR-1 and the mixed biofilm showed a wide range of compounds that this bacterium uses for the dissimilatory reduction of extracellular metal oxides, including riboflavin, iron-bound heme and heme biosynthetic intermediates, and the siderophore putrebactin.

  17. Performance and cost of energy transport and storage systems for dish applications using reversible chemical reactions

    Science.gov (United States)

    Schredder, J. M.; Fujita, T.

    1984-01-01

    The use of reversible chemical reactions for energy transport and storage for parabolic dish networks is considered. Performance and cost characteristics are estimated for systems using three reactions (sulfur-trioxide decomposition, steam reforming of methane, and carbon-dioxide reforming of methane). Systems are considered with and without storage, and in several energy-delivery configurations that give different profiles of energy delivered versus temperature. Cost estimates are derived assuming the use of metal components and of advanced ceramics. (The latter reduces the costs by three- to five-fold). The process that led to the selection of the three reactions is described, and the effects of varying temperatures, pressures, and heat exchanger sizes are addressed. A state-of-the-art survey was performed as part of this study. As a result of this survey, it appears that formidable technical risks exist for any attempt to implement the systems analyzed in this study, especially in the area of reactor design and performance. The behavior of all components and complete systems under thermal energy transients is very poorly understood. This study indicates that thermochemical storage systems that store reactants as liquids have efficiencies below 60%, which is in agreement with the findings of earlier investigators.

  18. Enhancing economic competiveness of dish Stirling technology through production volume and localization: Case study for Morocco

    Science.gov (United States)

    Larchet, Kevin; Guédez, Rafael; Topel, Monika; Gustavsson, Lars; Machirant, Andrew; Hedlund, Maria-Lina; Laumert, Björn

    2017-06-01

    The present study quantifies the reduction in the levelized cost of electricity (LCoE) and capital expenditure (CAPEX) of a dish Stirling power plant (DSPP) through an increase in localization and unit production volume. Furthermore, the localization value of the plant is examined to determine how much investment is brought into the local economy. Ouarzazate, Morocco, was chosen as the location of the study due to the country's favorable regulatory framework with regards to solar power technologies and its established industry in the concentrating solar power (CSP) field. A detailed techno-economic model of a DSPP was developed using KTH's in-house modelling tool DYESOPT, which allows power plant evaluation by means of technical and economic performance indicators. Results on the basis of LCoE and CAPEX were compared between two different cases of production volume, examining both a minimum and maximum level of localization. Thereafter, the DSPP LCoE and localization value were compared against competing solar technologies to evaluate its competitiveness. In addition, a sensitivity analysis was conducted around key design parameters. The study confirms that the LCoE of a DSPP can be reduced to values similar to solar photovoltaic (PV) and lower than other CSP technologies. Furthermore, the investment in the local economy is far greater when compared to PV and of the same magnitude to other CSP technologies. The competiveness of a DSPP has the potential to increase further when coupled with thermal energy storage (TES), which is currently under development.

  19. Association between Motives for Dish Choices during Home Meal Preparation and Weight Status in the NutriNet-Santé Study.

    Science.gov (United States)

    Ducrot, Pauline; Fassier, Philippine; Méjean, Caroline; Allès, Benjamin; Hercberg, Serge; Péneau, Sandrine

    2016-07-05

    Although home cooking has been associated with a lower body mass index in a few studies, no data exists on the motives behind food dish choices during home meal preparation and on their association with overweight. This study aimed to evaluate this association in 50,003 participants from the NutriNet-Santé cohort. Dimensions underlying the importance of 27 criteria possibly influencing dish choices were determined using an exploratory factor analysis. The association between dish choice motives and overweight (including obesity) was estimated using logistic regression models adjusted for sociodemographic and lifestyle characteristics. Five dimensions of dishes choice motives emerged: healthy diet (e.g., "nutritional balance of the dish"), constraints (e.g., "my cooking skills"), pleasure (e.g., "originality of the dish"), specific diets (e.g., "my health status"), and organization (e.g., "what I planned to eat"). A negative association was observed between the healthy diet factor and being overweight (OR = 0.65 (95% CI (confidence interval): 0.62-0.67)), whereas a positive association appeared for factors regarding pleasure (OR = 1.14 (95% CI: 1.10-1.19)) and specific diets (OR = 1.19 (95% CI: 1.17-1.22)). No significant associations were observed for constraints and organization. The significant associations between dish choice motives and overweight suggested the interest of focusing on these motives in order to promote healthier food choices during home cooking.

  20. Motives for dish choices during home meal preparation: results from a large sample of the NutriNet-Santé study.

    Science.gov (United States)

    Ducrot, Pauline; Méjean, Caroline; Allès, Benjamin; Fassier, Philippine; Hercberg, Serge; Péneau, Sandrine

    2015-09-30

    Although culinary practices have strongly evolved over time, few data are available on contemporary dish choices during meal preparation. We therefore sought to determine individual motives when choosing dishes to be prepared during weekdays and on weekends. The importance of 27 criteria related to dish choices was assessed in 53,025 participants in the NutriNet-Santé study. Dimensions of dish choice motives were investigated using exploratory factor analysis. Mean ratings of motives during weekdays and on weekends were compared using Student's t-test. Association between socio-demographic and cooking practice characteristics, and dish choice motives were evaluated using logistic regression models. Five dimensions of dish choice motives emerged: healthy diet (explained variance: 48.3%), constraints (19.0%), pleasure (12.1%), specific diets (11.0%) and organization (9.6%). The healthy diet factor was the most important on weekdays (mean rating 3.93) and weekends (3.90). Pleasure (3.61) had a higher score than constraints (3.54) on weekends (p < 0.0001) while the opposite was observed on weekdays (3.42 vs 3.77, respectively) (p < 0.0001). Organization was more important on weekdays (2.89) than on weekends (2.75) (p < 0.0001). Dish choice motives appeared to be significantly associated with socio-demographic and cooking practice characteristics. This study highlighted factors involved in dish choices in meal preparation on weekdays and weekends, as well as individual characteristics which determine motives for dish choices. From a public health perspective, these findings might help to develop appropriate strategies for promoting home meal preparation.

  1. Thermo-economic multi-objective optimization of solar dish-Stirling engine by implementing evolutionary algorithm

    International Nuclear Information System (INIS)

    Ahmadi, Mohammad H.; Sayyaadi, Hoseyn; Mohammadi, Amir H.; Barranco-Jimenez, Marco A.

    2013-01-01

    Highlights: • Thermo-economic multi-objective optimization of solar dish-Stirling engine is studied. • Application of the evolutionary algorithm is investigated. • Error analysis is done to find out the error through investigation. - Abstract: In the recent years, remarkable attention is drawn to Stirling engine due to noticeable advantages, for instance a lot of resources such as biomass, fossil fuels and solar energy can be applied as heat source. Great number of studies are conducted on Stirling engine and finite time thermo-economic is one of them. In the present study, the dimensionless thermo-economic objective function, thermal efficiency and dimensionless power output are optimized for a dish-Stirling system using finite time thermo-economic analysis and NSGA-II algorithm. Optimized answers are chosen from the results using three decision-making methods. Error analysis is done to find out the error through investigation

  2. Mouthwatering but erosive? A preliminary assessment of the acidity of a basic sauce used in many Indian dishes.

    Science.gov (United States)

    Ghai, Nandini; Burke, F J Trevor

    2012-12-01

    The aim of this study was to assess whether some types of Indian cuisine may contain erosive components. Indian dishes were prepared by a previously published method and their pH measured using a pH probe. The results indicated: (i) that some components of Indian cooking, such as tomatoes and red chilli powder, had the potential to erode enamel; (ii) that the pH of some foods was reduced with increasing temperature; and (iii) that all the basic masalas made and tested had a pH of less than 4.5. Within the limitations of the study, it may be concluded that the basic sauce/masala used in north Indian dishes may have erosive potential. This information could be considered useful when advising patients who eat Indian curries about causes of acid erosion of their teeth.

  3. Water Content in the SW USA Mantle Lithosphere: FTIR Analysis of Dish Hill and Kilbourne Hole Pyroxenites

    Science.gov (United States)

    Gibler, Robert; Peslier, Anne H.; Schaffer, Lillian Aurora; Brandon, Alan D.

    2014-01-01

    Kilbourne Hole (NM, USA) and Dish Hill (CA, USA) mantle xenoliths sample continental mantle in two different tectonic settings. Kilbourne Hole (KH) is located in the Rio Grande rift. Dish Hill (DH) is located in the southern Mojave province, an area potentially affected by subduction of the Farallon plate beneath North America. FTIR analyses were obtained on well characterized pyroxenite, dunite and wehrlite xenoliths, thought to represent crystallized melts at mantle depths. PUM normalized REE patterns of the KH bulk-rocks are slightly LREE enriched and consistent with those of liquids generated by 6% melting of a spinel peridotite source. Pyroxenite pyroxenes have no detectable water but one DH wehrlite, which bulk-rock is LREE enriched, has 4 ppm H2O in orthopyroxene and 2 Ga. The Farallon subduction appears to have enriched in water the southwestern United States lithospheric mantle further east than DH, beneath the Colorado plateau.

  4. Preference and intake frequency of high sodium foods and dishes and their correlations with anthropometric measurements among Malaysian subjects

    OpenAIRE

    Choong, Stella Sinn-Yee; Balan, Sumitha Nair; Chua, Leong-Siong; Say, Yee-How

    2012-01-01

    This study investigated the preference and intake frequency of a list of 15 commonly available high sodium Malaysian foods/dishes, discretionary salt use, and their possible association with demographics, blood pressures and anthropometric measurements among 300 Malaysian university students (114 males, 186 females; 259 ethnic Chinese, 41 Indians; 220 lean, 80 overweight). French fries and instant soup noodle were found to be the most preferred and most frequently consumed salty food, respect...

  5. Evaluation of the comprehensive palatability of Japanese sake paired with dishes by multiple regression analysis based on subdomains.

    Science.gov (United States)

    Nakamura, Ryo; Nakano, Kumiko; Tamura, Hiroyasu; Mizunuma, Masaki; Fushiki, Tohru; Hirata, Dai

    2017-08-01

    Many factors contribute to palatability. In order to evaluate the palatability of Japanese alcohol sake paired with certain dishes by integrating multiple factors, here we applied an evaluation method previously reported for palatability of cheese by multiple regression analysis based on 3 subdomain factors (rewarding, cultural, and informational). We asked 94 Japanese participants/subjects to evaluate the palatability of sake (1st evaluation/E1 for the first cup, 2nd/E2 and 3rd/E3 for the palatability with aftertaste/afterglow of certain dishes) and to respond to a questionnaire related to 3 subdomains. In E1, 3 factors were extracted by a factor analysis, and the subsequent multiple regression analyses indicated that the palatability of sake was interpreted by mainly the rewarding. Further, the results of attribution-dissections in E1 indicated that 2 factors (rewarding and informational) contributed to the palatability. Finally, our results indicated that the palatability of sake was influenced by the dish eaten just before drinking.

  6. Variations in Nutrients Composition of Most Commonly Consumed Cassava (Manihot esculenta Mixed Dishes in South-Eastern Nigeria

    Directory of Open Access Journals (Sweden)

    G. I. Davidson

    2017-01-01

    Full Text Available Variations in nutrient composition of most commonly consumed cassava (Manihot esculenta mixed dishes in South-eastern Nigeria were determined. Four communities were randomly selected from each of the five states in the South-east. Focus group discussions (FGD were conducted in each of the communities to determine commonly consumed foods and variations in recipes. 24-Hour dietary recall was conducted using 50 randomly selected households in those communities. Recipes collected during the FGD were standardized, prepared, and chemically analysed using standard methods. Data were analysed using descriptive statistics. Cassava-based dishes were the most commonly consumed in South-eastern Nigeria. Ninety-two percent of the study population ate cassava either in form of “fufu” (fermented cassava meal/garri (fermented and roasted cassava meal with soup or as “abacha” (tapioca salad. Commonly consumed soups were melon (Citrullus vulgaris seeds, “ora” (Pterocarpus soyauxii, and vegetable soups. Seven melon seed, six “ora,” and four vegetable soups and five “abacha” variations were identified. Except for vegetable soup, coefficient of variation for moisture was <10%, while large variations (19–71% were observed for energy and nutrients. These variations in cassava-based dishes need to be reflected in the country-specific food composition database to enable nutrient intake assessment or provision of dietary guidance using such food composition database as a reference material to be more effective.

  7. Dish/Stirling Hybrid-Receiver Sub-Scale Tests and Full-Scale Design

    International Nuclear Information System (INIS)

    Andraka, Charles; Bohn, Mark S.; Corey, John; Mehos, Mark; Moreno, James; Rawlinson, Scott

    1999-01-01

    We have designed and tested a prototype dish/Stirling hybrid-receiver combustion system. The system consists of a pre-mixed natural-gas burner heating a pin-finned sodium heat pipe. The design emphasizes simplicity, low cost, and ruggedness. Our test was on a 1/6 th -scale device, with a nominal firing rate of 18kWt, a power throughput of 13kWt, and a sodium vapor temperature of 750 ampersand deg;C. The air/fuel mixture was electrically preheated to 640 ampersand deg;C to simulate recuperation. The test rig was instrumented for temperatures, pressures, flow rates, overall leak rate, and exhaust emissions. The data verify our burner and heat-transfer models. Performance and post-test examinations validate our choice of materials and fabrication methods. Based on the 1/6 th -scale results, we are designing a till-scale hybrid receiver. This is a fully-integrated system, including burner, pin-fin primary heat exchanger, recuperator (in place of the electrical pre-heater used in the prototype system), solar absorber, and sodium heat pipe. The major challenges of the design are to avoid pre-ignition, achieve robust heat-pipe performance, and attain long life of the burner matrix, recuperator, and flue-gas seals. We have used computational fluid dynamics extensively in designing to avoid pre-ignition and for designing the heat-pipe wick, and we have used individual component tests and results of the 1/6 th -scale test to optimize for long life. In this paper, we present our design philosophy and basic details of our design. We describe the sub-scale test rig and compare test results with predictions. Finally, we outline the evolution of our full-scale design, and present its current status

  8. Stretched membrane heliostats: design and structural analysis of reflectance module and support of a heliostats of 9 m. diaform and 60 m''3 of reflectance surface; Diseno y analisis estructural del modulo reflectante y estructura soporte de un heliostato de 9 m. de diametro y 60 m2 de superficie reflectante

    Energy Technology Data Exchange (ETDEWEB)

    Figarola Torres, J M

    1993-07-01

    After having designed and built at CIEMAT a first prototype of a Btretched membrane heliostats of 3 m. diameter, the design and the structural analysis of the different components included in the reflectance module and support of another heliostats, this one of 9 m. diameter and 60 m2. of reflectance surface, are shown In this report. This last heliostats will be mounted on a pedestal and its driving device at the Solar Platform of Almeria. In order to optimize design and performance, the structural analysis of its basic components has been analyzed with the finite elements program ANSYS. The following elements have been subject to analysis: the membrane and their ring supports, stretching system and the structural support. A similar scheme to the one applied to the previous prototype has been used on the focus control system. That includes a linear transducer, a variable frequency and a fan. Finally it has to be pointed out that substantial improvements have been achieved with respect to the first prototype concerning design and cost. (Author) 5 refs.

  9. Stretched membrane heliostats: design and structural analysis of reflectance module and support of a heliostats of 9 m. diaform and 60 m''3 of reflectance surface; Diseno y analisis estructural del modulo reflectante y estructura soporte de un heliostato de 9 m. de diametro y 60 m2 de superficie reflectante

    Energy Technology Data Exchange (ETDEWEB)

    Figarola Torres, J. M.

    1993-07-01

    After having designed and built at CIEMAT a first prototype of a Btretched membrane heliostats of 3 m. diameter, the design and the structural analysis of the different components included in the reflectance module and support of another heliostats, this one of 9 m. diameter and 60 m2. of reflectance surface, are shown In this report. This last heliostats will be mounted on a pedestal and its driving device at the Solar Platform of Almeria. In order to optimize design and performance, the structural analysis of its basic components has been analyzed with the finite elements program ANSYS. The following elements have been subject to analysis: the membrane and their ring supports, stretching system and the structural support. A similar scheme to the one applied to the previous prototype has been used on the focus control system. That includes a linear transducer, a variable frequency and a fan. Finally it has to be pointed out that substantial improvements have been achieved with respect to the first prototype concerning design and cost. (Author) 5 refs.

  10. Spatially Extended and High-Velocity Dispersion Molecular Component in Spiral Galaxies: Single-Dish Versus Interferometric Observations

    Science.gov (United States)

    Caldú-Primo, Anahi; Schruba, Andreas; Walter, Fabian; Leroy, Adam; Bolatto, Alberto D.; Vogel, Stuart

    2015-02-01

    Recent studies of the molecular medium in nearby galaxies have provided mounting evidence that the molecular gas can exist in two phases: one that is clumpy and organized as molecular clouds and another one that is more diffuse. This last component has a higher velocity dispersion than the clumpy one. In order to investigate these two molecular components further, we compare the fluxes and line widths of CO in NGC 4736 and NGC 5055, two nearby spiral galaxies for which high-quality interferometric as well as single-dish data sets are available. Our analysis leads to two main results: (1) employing three different methods, we determine the flux recovery of the interferometer as compared to the single-dish to be within a range of 35%-74% for NGC 4736 and 81%-92% for NGC 5055, and (2) when focusing on high (S/N ≥ 5) lines of sight (LOSs), the single-dish line widths are larger by ˜(40 ± 20)% than the ones derived from interferometric data, which is in agreement with stacking all LOSs. These results point to a molecular gas component that is distributed over spatial scales larger than 30″(˜1 kpc), and is therefore filtered out by the interferometer. The available observations do not allow us to distinguish between a truly diffuse gas morphology and a uniform distribution of small clouds that are separated by less than the synthesized beam size (˜3″ or ˜100 pc), as they would both be invisible for the interferometer. This high velocity dispersion component has a dispersion similar to what is found in the atomic medium, as traced through observations of the H i line.

  11. Spatially extended and high-velocity dispersion molecular component in spiral galaxies: Single-dish versus interferometric observations

    International Nuclear Information System (INIS)

    Caldú-Primo, Anahi; Walter, Fabian; Schruba, Andreas; Leroy, Adam; Bolatto, Alberto D.; Vogel, Stuart

    2015-01-01

    Recent studies of the molecular medium in nearby galaxies have provided mounting evidence that the molecular gas can exist in two phases: one that is clumpy and organized as molecular clouds and another one that is more diffuse. This last component has a higher velocity dispersion than the clumpy one. In order to investigate these two molecular components further, we compare the fluxes and line widths of CO in NGC 4736 and NGC 5055, two nearby spiral galaxies for which high-quality interferometric as well as single-dish data sets are available. Our analysis leads to two main results: (1) employing three different methods, we determine the flux recovery of the interferometer as compared to the single-dish to be within a range of 35%–74% for NGC 4736 and 81%–92% for NGC 5055, and (2) when focusing on high (S/N ≥ 5) lines of sight (LOSs), the single-dish line widths are larger by ∼(40 ± 20)% than the ones derived from interferometric data, which is in agreement with stacking all LOSs. These results point to a molecular gas component that is distributed over spatial scales larger than 30″(∼1 kpc), and is therefore filtered out by the interferometer. The available observations do not allow us to distinguish between a truly diffuse gas morphology and a uniform distribution of small clouds that are separated by less than the synthesized beam size (∼3″ or ∼100 pc), as they would both be invisible for the interferometer. This high velocity dispersion component has a dispersion similar to what is found in the atomic medium, as traced through observations of the H i line.

  12. Differences in nutrient composition and choice of side dishes between red meat and fish dinners in Norwegian adults

    Directory of Open Access Journals (Sweden)

    Jannicke Borch Myhre

    2016-01-01

    Full Text Available Background: Food-based dietary guidelines often recommend increased consumption of fish and reduced intake of red and processed meat. However, little is known about how changing the main protein source from red meat to fish may influence the choice of side dishes. Objective: To investigate whether side dish choices differed between red meat and fish dinners. Moreover, to compare intakes of macronutrients and selected micronutrients in red meat and fish dinners and to see whether whole-day intakes of these nutrients differed between days with red meat dinners and days with fish dinners. Design: Data were collected in a cross-sectional nationwide Norwegian dietary survey using two non-consecutive telephone-administered 24-h recalls. The recalls were conducted approximately 4 weeks apart. In total, 2,277 dinners from 1,517 participants aged 18–70 were included in the analyses. Results: Fish dinners were more likely to include potatoes and carrots than red meat dinners, whereas red meat dinners more often contained bread, tomato sauce, and cheese. Red meat dinners contained more energy and iron; had higher percentages of energy (E% from fat, saturated fat, and monounsaturated fat; and a lower E% from protein and polyunsaturated fat than fish dinners. Fish dinners contained more vitamin D, β-carotene, and folate than red meat dinners. Similar differences were found when comparing whole-day intakes of the same nutrients on days with red meat versus fish dinners. Conclusion: Fish dinners were accompanied by different side dishes than red meat dinners. With regard to nutrient content, fish dinners generally had a healthier profile than red meat dinners. However, iron intake was higher for red meat dinners. Information about associated foods will be useful both for developing public health guidelines and when studying associations between dietary factors and health outcomes.

  13. Vegetables and Mixed Dishes Are Top Contributors to Phylloquinone Intake in US Adults: Data from the 2011-2012 NHANES.

    Science.gov (United States)

    Harshman, Stephanie G; Finnan, Emily G; Barger, Kathryn J; Bailey, Regan L; Haytowitz, David B; Gilhooly, Cheryl H; Booth, Sarah L

    2017-07-01

    Background: Phylloquinone is the most abundant form of vitamin K in US diets. Green vegetables are considered the predominant dietary source of phylloquinone. As our food supply diversifies and expands, the food groups that contribute to phylloquinone intake are also changing, which may change absolute intakes. Thus, it is important to identify the contributors to dietary vitamin K estimates to guide recommendations on intakes and food sources. Objective: The purpose of this study was to estimate 1 ) the amount of phylloquinone consumed in the diet of US adults, 2 ) to estimate the contribution of different food groups to phylloquinone intake in individuals with a high or low vegetable intake (≥2 or vegetables/d), and 3 ) to characterize the contribution of different mixed dishes to phylloquinone intake. Methods: Usual phylloquinone intake was determined from NHANES 2011-2012 (≥20 y old; 2092 men and 2214 women) and the National Cancer Institute Method by utilizing a complex, stratified, multistage probability-cluster sampling design. Results: On average, 43.0% of men and 62.5% of women met the adequate intake (120 and 90 μg/d, respectively) for phylloquinone, with the lowest self-reported intakes noted among men, especially in the older age groups (51-70 and ≥71 y). Vegetables were the highest contributor to phylloquinone intake, contributing 60.0% in the high-vegetable-intake group and 36.1% in the low-vegetable-intake group. Mixed dishes were the second-highest contributor to phylloquinone intake, contributing 16.0% in the high-vegetable-intake group and 28.0% in the low-vegetable-intake group. Conclusion: Self-reported phylloquinone intakes from updated food composition data applied to NHANES 2011-2012 reveal that fewer men than women are meeting the current adequate intake. Application of current food composition data confirms that vegetables continue to be the primary dietary source of phylloquinone in the US diet. However, mixed dishes and convenience

  14. Effect of soil-structure interaction on the seismic behaviour of pedestal-structure system in large dish antennas

    Directory of Open Access Journals (Sweden)

    Bahador Pourhatami

    2017-12-01

    Full Text Available Regarding the progressive improvement in the territory of Space Technology in all developed countries and consequently developing countries including Islamic Republic of Iran, the optimization of design and utilization of the communication equipment has been paid more attention today. For instance, considering recent highly innovative methods, specifically in communication field, developed for design, manufacturing and exploiting dish antenna for specific cases, cooperation of other science and technology experts, like civil engineers, is also necessary. In this way, more delicate design procedure in order to satisfy communication requirement, is achieved. So far, no specific investigation about aforementioned subject, especially the effect of soil-structure interaction (SSI in analysing the seismic behaviour of communication large dish antennas has been conducted in Iran. In this paper, with the aim of investigating the effect of SSI on seismic behavior of pedestal, first an acceptable range for antenna displacement – as the most important parameter in pedestal structure for antenna – in both operational and survival states, has been calculated numerically based on generic formula. Secondly, the modelling of the whole pedestal-structure system has been modelled subjected to the associated loads and other primary conditions. This procedure has been performed once without considering the SSI and once more with it. Comparison of the obtained results shows that considering the SSI would impress the output results with a difference rate more than 50% and 600% respectively at survival and operational condition.

  15. Analysis of ewe’s milk by FT Near Infrared spectroscopy: measurement of samples on Petri dishes in reflectance mode

    Directory of Open Access Journals (Sweden)

    Květoslava Šustová

    2006-01-01

    Full Text Available Our work deals with a possibility of determination of basic composition (dry matter, fat, protein, casein, lactose and urea nitrogen of ewe’s milk and colostrum by FT NIR spectroscopy. Samples of milk were warmed to 40 °C, agitated, cooled to 20 °C, transferred into Petri dishes and analysed by reference methods and by FT NIR in reflectance mode. The measured area was spaced by a metallic mirror. Statistically significant differences between the reference values and the calculated values of NIR were not found (p=0.05. Results of calibration for ewe’s milk determined the highest correlation coefficients: dry matter 0.983, fat 0.989, true protein 0.997, casein 0.977, lactose 0.980 and urea nitrogen 0.973. The study showed that NIRS method, when samples of milk are measured on Petri dishes, is a useful technique for the prediction of dry matter, fat, protein and casein in ewe’s milk.

  16. Distance distribution of bystander effects in alpha-particle irradiated cell populations using a CR-39-based culture dish

    International Nuclear Information System (INIS)

    Gaillard, S.; Pusset, D.; Toledo, S.M. de; Azzam, E.I.; Fromm, M.

    2008-01-01

    Propagation of induced biological effects from irradiated to non-irradiated cells is known to occur in cell cultures exposed to low fluences of charged particles. These bystander effects are currently investigated using microbeam or non-microbeam (broad beams) irradiation techniques. Identification of the targeted and non-targeted bystander cells is critical to our understanding of mechanisms underlying such effects. We developed a novel cell culture dish where the base consists of a thin CR-39 sheet grafted on a thin polyethylene terephthalate (PET) foil. The validity of this device in identifying not only irradiated cells, but also the cellular compartment traversed by the particle track is described. We have optimized track etch parameters that do not interfere with measurement of induced biological endpoints under normal incident irradiation. Thus the culture dishes can be used to determine distance distributions for the propagation of induced biological effects from a hit cell to bystander cells. We describe the computer code developed to determine the distance distributions of propagated biological stress responses in normal human fibroblast cells exposed to very low fluences of alpha particles

  17. Application of the monazite radiation source to the petri dish-type cloud chamber and the influence of several factors on occurrence of tracks

    International Nuclear Information System (INIS)

    Hayakawa, Issei; Sago, Yutaka; Mori, Chizuo

    2012-01-01

    Monazite radiation source (2.5 mmΦ) proved to be useful as a radiation source of cloud chamber without the dispersion of powder or its adhesion because of a sintered body. After the track appeared within one minute after having put the petri dish on the dry ice, the number increased rapidly followed by the tendency to decrease gradually after that. The tracks can be observed for about 20 minutes after cooled with dry ice. The size of dry ice should be chosen to enter the inside of the bottom edge of the petri dish. The same number of tracks as using conventional mantle radiation source was obtained by utilizing 3 pieces of monazite sintered body separated mutually by about 7.5 mm. Hence the petri dish-type cloud chamber with the monazite sintered body as radiation source revealed to make the observation of track easy and prompt. (author)

  18. Sizing a solar dish Stirling micro-CHP system for residential application in diverse climatic conditions based on 3E analysis

    International Nuclear Information System (INIS)

    Moghadam, Ramin Shabanpour; Sayyaadi, Hoseyn; Hosseinzade, Hadi

    2013-01-01

    Highlights: • 3E analysis was performed on solar CHP systems. • Significant primary energy saving and greenhouse gas reduction were obtained. • The engine was sized so that it had the best economic sound. • Various criteria at different weathers were used for sizing the engine. - Abstract: A solar dish Stirling cogeneration system is considered to provide energy demands of a residential building. As energy demands of the building and output power of the engine are functions of weather condition and solar irradiation flux, the benchmark building was considered to be located in five different cities in Iran with diverse climatic and solar irradiation conditions. The proposed solar dish Stirling micro-CHP system was analyzed based on 3E analysis. The 3E analysis evaluated primary energy saving analysis (energy analysis), carbon dioxide emission reduction (environmental analysis) and payback period for return of investment (economic analysis) and was compared to a reference building that utilized primary energy carriers for its demands. Three scenarios were considered for assessment and sizing the solar dish Stirling engine. In the first scenario, size of the solar dish Stirling engine was selected based on the lowest annual electric power demand while, in second, the highest annual electric power consumption was considered to specify size of the engine. In the third scenario, a solar dish Stirling engine with constant output capacity was considered for the five locations. It was shown that implementing the solar dish Stirling micro-CHP system had good potential in primary energy saving and carbon dioxide emission reduction in all scenarios and acceptable payback period for return of the investment in some scenarios. Finally, the best scenario for selecting size of the engine in each city was introduced using the TOPSIS decision making method. It was demonstrated that, for dry weather, the first scenario was the best while, for hot and humid cities and

  19. Association between the frequency of meals combining "Shushoku, Shusai, and Hukusai" (Staple food, main dish, and side dish) and intake of nutrients and food groups among Japanese young adults aged 18-24 years: a cross-sectional study.

    Science.gov (United States)

    Kakutani, Yuya; Kamiya, Saori; Omi, Naomi

    2015-01-01

    "Shushoku," "Shusai," and "Hukusai" are staple food, main dish, and side dish, respectively. The recommended meal in Japan is a combination of "Shushoku," "Shusai," and "Hukusai"; however, it remains unclear whether there is an association between the frequency of these meals and intake of nutrients and food groups. This cross-sectional study examined the association between the frequency of meals combining "Shushoku, Shusai, and Hukusai" and intake of nutrients and food groups among 664 Japanese young adults aged 18-24 y. The dietary habits of the subjects during the preceding month were assessed using a validated brief-type self-administered diet history questionnaire. The frequency of meals combining "Shushoku, Shusai, and Hukusai" was self-reported according to four categories: "less than 1 d or 1 d/wk," "2 or 3 d/wk," "4 or 5 d/wk," and "every day." In both women and men, there was an association between the higher frequency of these meals and higher intake of the following food groups: pulses, green and yellow vegetables, other vegetables, mushrooms, seaweeds, fish and shellfish, and eggs. Moreover, there was an association with higher intake of protein, polyunsaturated fat, n-6 and n-3 polyunsaturated fat, total dietary fiber, soluble and insoluble dietary fiber, β-carotene, α-tocopherol, vitamin K, thiamin, riboflavin, folate, pantothenic acid, vitamin C, potassium, calcium, magnesium, iron, and copper, and lower intake of carbohydrate in both women and men. Our findings support the hypothesis that the meals combining "Shushoku, Shusai, and Hukusai" may be associated with intake of many food groups and nutrients among Japanese young adults.

  20. Child and parent perspectives on healthier side dishes and beverages in restaurant kids' meals: results from a national survey in the United States.

    Science.gov (United States)

    Shonkoff, Eleanor T; Anzman-Frasca, Stephanie; Lynskey, Vanessa M; Chan, Grace; Glenn, Meaghan E; Economos, Christina D

    2017-07-25

    Children frequently consume foods from restaurants; considering the quick-service sector alone, 1/3 of children eat food from these restaurants on a given day, and among these consumers, 1/3 of their daily calories come from fast food. Restaurant foods and beverages are second only to grocery store foods and beverages in their contribution to total energy intake of U.S. 4- to 11-year-olds. Shifting their restaurant consumption in healthier directions could have a positive impact on child health. In 2014 this study examined self-reported child receptivity and parent awareness of child receptivity to ordering a fruit or vegetable side dish instead of French fries; and milk, water, or flavored water instead of soda/pop with a kids' meal when eating out. Child receptivity to side dishes was compared between 2010 and 2014. An online survey was administered by Nielsen via their Harris Poll Online to a national panel of 711 parents and their 8- to 12-year-old child, as part of a larger study. Frequencies, logistic regressions, t-tests, chi-square tests, and percent agreement were used to evaluate child likelihood of ordering certain side dishes; receptivity to healthier side dish and beverage alternatives; changes in receptivity to healthier sides across years; and parent awareness. A majority of children said they were likely to order a meal with a vegetable (60%), fruit (78%), or French fry (93%) side dish. They were receptive to receiving a fruit or vegetable (FV) side dish instead of French fries (68%); or milk, water, or flavored water instead of soda (81%) with their restaurant kids' meal. Liking/taste was the most common reason for children's feelings. Child receptivity to a FV side dish instead of French fries was high in both years and significantly higher in 2014 (t = -2.12, p = 0.034). The majority of parent and child reports of child receptivity were concordant (85%). These national survey results indicate that children are receptive to FV side dishes and

  1. Assessing intake of spices by pattern of spice use, frequency of consumption and portion size of spices consumed from routinely prepared dishes in southern India.

    Science.gov (United States)

    Siruguri, Vasanthi; Bhat, Ramesh V

    2015-01-11

    Measurement of dietary intake of spices is gaining significance because of recognition of their health promoting benefits as well as its use for risk assessment of contaminant exposures. Estimating intake of spices at the individual level, presents several challenges since various spices are used as an integrated part of a prepared food and consumed in amounts much smaller than other dietary components. The objective of the present study is to assess intake of spices at the household and individual level on the basis of pattern of spice use and portion size of spice consumed from routinely prepared dishes in Hyderabad city in Southern India. The study was conducted in 100 households in urban areas of Hyderabad city in India with the help of a spice intake questionnaire that was prepared to collect information on the pattern of spice use, frequency, and quantity of spice consumption of 17 spices routinely used in Indian cuisine. The quantity of spice intake was assessed by measuring portion size of spice consumed from the quantity of i) spices added in routinely prepared dishes and ii) the prepared dish consumed by an individual. Based on the type of dish prepared and frequency of preparing the dishes, 11 out of 17 spices were found to be consumed by more than 50% of the households. Maximum number of spices was consumed at weekly frequencies. Red chillies and turmeric were the most frequently consumed spices by 100% of the households. The mean total intake of spices was observed to be higher through dishes consumed daily (10.4 g/portion) than from those consumed at weekly or monthly frequencies. Highest portion size intake was observed for chillies (mean 3.0 g; range 0.05-20.2 g) and lowest for nutmeg (mean 0.14 g; range 0.02-0.64 g) and mace (mean 0.21 g; range: 0.02-0.6 g). The study suggested that assessment of intake of spices varies with frequency of use of spices and type of dish consumed. Portion size estimations of spices consumed and the frequency of

  2. Child and parent perspectives on healthier side dishes and beverages in restaurant kids’ meals: results from a national survey in the United States

    Directory of Open Access Journals (Sweden)

    Eleanor T. Shonkoff

    2017-07-01

    Full Text Available Abstract Background Children frequently consume foods from restaurants; considering the quick-service sector alone, 1/3 of children eat food from these restaurants on a given day, and among these consumers, 1/3 of their daily calories come from fast food. Restaurant foods and beverages are second only to grocery store foods and beverages in their contribution to total energy intake of U.S. 4- to 11-year-olds. Shifting their restaurant consumption in healthier directions could have a positive impact on child health. In 2014 this study examined self-reported child receptivity and parent awareness of child receptivity to ordering a fruit or vegetable side dish instead of French fries; and milk, water, or flavored water instead of soda/pop with a kids’ meal when eating out. Child receptivity to side dishes was compared between 2010 and 2014. Methods An online survey was administered by Nielsen via their Harris Poll Online to a national panel of 711 parents and their 8- to 12-year-old child, as part of a larger study. Frequencies, logistic regressions, t-tests, chi-square tests, and percent agreement were used to evaluate child likelihood of ordering certain side dishes; receptivity to healthier side dish and beverage alternatives; changes in receptivity to healthier sides across years; and parent awareness. Results A majority of children said they were likely to order a meal with a vegetable (60%, fruit (78%, or French fry (93% side dish. They were receptive to receiving a fruit or vegetable (FV side dish instead of French fries (68%; or milk, water, or flavored water instead of soda (81% with their restaurant kids’ meal. Liking/taste was the most common reason for children’s feelings. Child receptivity to a FV side dish instead of French fries was high in both years and significantly higher in 2014 (t = −2.12, p = 0.034. The majority of parent and child reports of child receptivity were concordant (85%. Conclusions These national survey

  3. The Flexitarian Flip™ : Testing the Modalities of Flavor as Sensory Strategies to Accomplish the Shift from Meat-Centered to Vegetable-Forward Mixed Dishes.

    Science.gov (United States)

    Spencer, Molly; Guinard, Jean-Xavier

    2018-01-01

    The American diet is lacking in plant-based foods and vegetables, higher in protein than necessary, and too centered on meat and poultry. Two major dietary shifts recommended by the 2015-2020 U.S. Dietary Guidelines are to increase vegetable intake and to increase the variety of protein food sources. One suggested strategy for doing this is to partially replace meat and poultry with vegetables and plant-based ingredients in mixed dishes. This research tested the potential of flavor modalities (taste, aroma, trigeminal, and their combination) as strategies to increase the sensory appeal of plant-forward dishes. Consumer testing (n = 141) was conducted in a cross-sectional design in a laboratory setting on 24 recipe variations. Three factors were tested: cuisine (Latin American, Mediterranean, and Asian), meat proportion (high-meat/low-vegetable versus low-meat/high-vegetable), and flavor strategy (taste, aroma, trigeminal, and a reduced-intensity trimodal combination). Statistical analysis was performed in R and XLSTAT-Sensory ® 2017. Four consumer preference segments were uncovered. The low-meat dishes achieved parity or higher in consumer acceptance across all recipes and flavor strategies. The taste and trigeminal strategies both had higher overall acceptability scores than the aroma strategy, and the differences were significant (P meat with vegetables in mixed dishes. The trigeminal and trimodal combination strategies were found to be the most promising flavor modalities to use to implement this shift. There is little knowledge of American consumer preferences regarding vegetables in mixed dishes. Mixed dishes are a strategy recommended by the U.S. Dietary Guidelines to increase vegetable consumption and variety of protein sources. This research explores various flavor and culinary strategies with which to carry out the mixed dish meat-vegetable swap and to test the potential of the Flexitarian Flip ™ (the shift from meat-centric to plant-centric diets

  4. Book Review: It's Not You, It's the Dishes: How to Minimize Conflict and Maximize Happiness in Your Relationship

    Directory of Open Access Journals (Sweden)

    Derek Lawson

    2014-08-01

    Full Text Available It’s Not You, It’s The Dishes brings economic principles and theory into the married life of couples. The authors simplify economics by providing fundamental concepts while removing technical jargon in a funny, yet intuitive way. Readers are introduced to the basics of comparative advantage, game theory, and eight other economic principles, all while learning lessons on how to resourcefully allocate their limited units of time, money, and energy to yield a better return on their biggest investment of their lives, their marriage. At its core, this is a self-help book aimed at married couples. Nevertheless, financial professionals and academics may benefit from reading the book, particularly because it may be beneficial helping to brainstorm potential solutions with their clients or as “homework” for client couples.

  5. Directed midbrain and spinal cord neurogenesis from pluripotent stem cells to model development and disease in a dish.

    Science.gov (United States)

    Allodi, Ilary; Hedlund, Eva

    2014-01-01

    Induction of specific neuronal fates is restricted in time and space in the developing CNS through integration of extrinsic morphogen signals and intrinsic determinants. Morphogens impose regional characteristics on neural progenitors and establish distinct progenitor domains. Such domains are defined by unique expression patterns of fate determining transcription factors. These processes of neuronal fate specification can be recapitulated in vitro using pluripotent stem cells. In this review, we focus on the generation of dopamine neurons and motor neurons, which are induced at ventral positions of the neural tube through Sonic hedgehog (Shh) signaling, and defined at anteroposterior positions by fibroblast growth factor (Fgf) 8, Wnt1, and retinoic acid (RA). In vitro utilization of these morphogenic signals typically results in the generation of multiple neuronal cell types, which are defined at the intersection of these signals. If the purpose of in vitro neurogenesis is to generate one cell type only, further lineage restriction can be accomplished by forced expression of specific transcription factors in a permissive environment. Alternatively, cell-sorting strategies allow for selection of neuronal progenitors or mature neurons. However, modeling development, disease and prospective therapies in a dish could benefit from structured heterogeneity, where desired neurons are appropriately synaptically connected and thus better reflect the three-dimensional structure of that region. By modulating the extrinsic environment to direct sequential generation of neural progenitors within a domain, followed by self-organization and synaptic establishment, a reductionist model of that brain region could be created. Here we review recent advances in neuronal fate induction in vitro, with a focus on the interplay between cell intrinsic and extrinsic factors, and discuss the implications for studying development and disease in a dish.

  6. THE HYDROGEN EPOCH OF REIONIZATION ARRAY DISH. II. CHARACTERIZATION OF SPECTRAL STRUCTURE WITH ELECTROMAGNETIC SIMULATIONS AND ITS SCIENCE IMPLICATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Ewall-Wice, Aaron; Hewitt, Jacqueline; Neben, Abraham R. [MIT Kavli Institute for Cosmological Physics, Cambridge, MA, 02139 (United States); Bradley, Richard; Dickenson, Roger; Doolittle, Phillip; Egan, Dennis; Hedrick, Mike; Klima, Patricia [National Radio Astronomy Observatory, Charlottesville, VA (United States); Deboer, David; Parsons, Aaron; Ali, Zaki S.; Cheng, Carina; Patra, Nipanjana; Dillon, Joshua S. [Department of Astronomy, University of California, Berkeley, CA (United States); Aguirre, James [Department of Physics and Astronomy, University of Pennsylvania, Philadelphia, PA (United States); Bowman, Judd; Thyagarajan, Nithyanandan [Arizona State University, School of Earth and Space Exploration, Tempe, AZ 85287 (United States); Venter, Mariet [Department of Electrical and Electronic Engineering, Stellenbosch University, Stellenbosch, SA (South Africa); Acedo, Eloy de Lera [Cavendish Laboratory, University of Cambridge, Cambridge (United Kingdom); and others

    2016-11-10

    We use time-domain electromagnetic simulations to determine the spectral characteristics of the Hydrogen Epoch of Reionization Arrays (HERA) antenna. These simulations are part of a multi-faceted campaign to determine the effectiveness of the dish’s design for obtaining a detection of redshifted 21 cm emission from the epoch of reionization. Our simulations show the existence of reflections between HERA’s suspended feed and its parabolic dish reflector that fall below -40 dB at 150 ns and, for reasonable impedance matches, have a negligible impact on HERA’s ability to constrain EoR parameters. It follows that despite the reflections they introduce, dishes are effective for increasing the sensitivity of EoR experiments at a relatively low cost. We find that electromagnetic resonances in the HERA feed’s cylindrical skirt, which is intended to reduce cross coupling and beam ellipticity, introduces significant power at large delays (-40 dB at 200 ns), which can lead to some loss of measurable Fourier modes and a modest reduction in sensitivity. Even in the presence of this structure, we find that the spectral response of the antenna is sufficiently smooth for delay filtering to contain foreground emission at line-of-sight wave numbers below k {sub ∥} ≲ 0.2 h Mpc{sup -1}, in the region where the current PAPER experiment operates. Incorporating these results into a Fisher Matrix analysis, we find that the spectral structure observed in our simulations has only a small effect on the tight constraints HERA can achieve on parameters associated with the astrophysics of reionization.

  7. Preference and intake frequency of high sodium foods and dishes and their correlations with anthropometric measurements among Malaysian subjects.

    Science.gov (United States)

    Choong, Stella Sinn-Yee; Balan, Sumitha Nair; Chua, Leong-Siong; Say, Yee-How

    2012-06-01

    This study investigated the preference and intake frequency of a list of 15 commonly available high sodium Malaysian foods/dishes, discretionary salt use, and their possible association with demographics, blood pressures and anthropometric measurements among 300 Malaysian university students (114 males, 186 females; 259 ethnic Chinese, 41 Indians; 220 lean, 80 overweight). French fries and instant soup noodle were found to be the most preferred and most frequently consumed salty food, respectively, while salted fish was least preferred and least frequently consumed. Males had a significantly higher intake frequency of at least 6 of the salty foods, but the preference of most salty foods was not significantly different between genders. Ethnic Chinese significantly preferred more and took more frequently traditional and conventional Malaysian foods like asam laksa (a Malaysian salty-sour-spicy noodle in fish stock), salted biscuits and salted vegetable, while Indians have more affinity and frequency towards eating salty Western foods. Body Mass Index was significantly negatively correlated with the intake frequency of canned/packet soup and salted fish while waist circumference was significantly positively correlated with the preference of instant noodle. Also, an increased preference of potato chips and intake frequency of salted biscuits seemed to lead to a decreased WHR. Other than these, all the other overweight/obesity indicators did not seem to fully correlate with the salty food preference and intake frequency. Nevertheless, the preference and intake frequency of asam laksa seemed to be significant negative predictors for blood pressures. Finally, increased preference and intake frequency of high sodium shrimp paste (belacan)-based foods like asam laksa and belacan fried rice seemed to discourage discretionary salt use. In conclusion, the preference and intake frequency of the high sodium belacan-based dish asam laksa seems to be a good predictor for ethnic

  8. THE HYDROGEN EPOCH OF REIONIZATION ARRAY DISH. II. CHARACTERIZATION OF SPECTRAL STRUCTURE WITH ELECTROMAGNETIC SIMULATIONS AND ITS SCIENCE IMPLICATIONS

    International Nuclear Information System (INIS)

    Ewall-Wice, Aaron; Hewitt, Jacqueline; Neben, Abraham R.; Bradley, Richard; Dickenson, Roger; Doolittle, Phillip; Egan, Dennis; Hedrick, Mike; Klima, Patricia; Deboer, David; Parsons, Aaron; Ali, Zaki S.; Cheng, Carina; Patra, Nipanjana; Dillon, Joshua S.; Aguirre, James; Bowman, Judd; Thyagarajan, Nithyanandan; Venter, Mariet; Acedo, Eloy de Lera

    2016-01-01

    We use time-domain electromagnetic simulations to determine the spectral characteristics of the Hydrogen Epoch of Reionization Arrays (HERA) antenna. These simulations are part of a multi-faceted campaign to determine the effectiveness of the dish’s design for obtaining a detection of redshifted 21 cm emission from the epoch of reionization. Our simulations show the existence of reflections between HERA’s suspended feed and its parabolic dish reflector that fall below -40 dB at 150 ns and, for reasonable impedance matches, have a negligible impact on HERA’s ability to constrain EoR parameters. It follows that despite the reflections they introduce, dishes are effective for increasing the sensitivity of EoR experiments at a relatively low cost. We find that electromagnetic resonances in the HERA feed’s cylindrical skirt, which is intended to reduce cross coupling and beam ellipticity, introduces significant power at large delays (-40 dB at 200 ns), which can lead to some loss of measurable Fourier modes and a modest reduction in sensitivity. Even in the presence of this structure, we find that the spectral response of the antenna is sufficiently smooth for delay filtering to contain foreground emission at line-of-sight wave numbers below k ∥ ≲ 0.2 h Mpc -1 , in the region where the current PAPER experiment operates. Incorporating these results into a Fisher Matrix analysis, we find that the spectral structure observed in our simulations has only a small effect on the tight constraints HERA can achieve on parameters associated with the astrophysics of reionization.

  9. Preference and intake frequency of high sodium foods and dishes and their correlations with anthropometric measurements among Malaysian subjects

    Science.gov (United States)

    Choong, Stella Sinn-Yee; Balan, Sumitha Nair; Chua, Leong-Siong

    2012-01-01

    This study investigated the preference and intake frequency of a list of 15 commonly available high sodium Malaysian foods/dishes, discretionary salt use, and their possible association with demographics, blood pressures and anthropometric measurements among 300 Malaysian university students (114 males, 186 females; 259 ethnic Chinese, 41 Indians; 220 lean, 80 overweight). French fries and instant soup noodle were found to be the most preferred and most frequently consumed salty food, respectively, while salted fish was least preferred and least frequently consumed. Males had a significantly higher intake frequency of at least 6 of the salty foods, but the preference of most salty foods was not significantly different between genders. Ethnic Chinese significantly preferred more and took more frequently traditional and conventional Malaysian foods like asam laksa (a Malaysian salty-sour-spicy noodle in fish stock), salted biscuits and salted vegetable, while Indians have more affinity and frequency towards eating salty Western foods. Body Mass Index was significantly negatively correlated with the intake frequency of canned/packet soup and salted fish while waist circumference was significantly positively correlated with the preference of instant noodle. Also, an increased preference of potato chips and intake frequency of salted biscuits seemed to lead to a decreased WHR. Other than these, all the other overweight/obesity indicators did not seem to fully correlate with the salty food preference and intake frequency. Nevertheless, the preference and intake frequency of asam laksa seemed to be significant negative predictors for blood pressures. Finally, increased preference and intake frequency of high sodium shrimp paste (belacan)-based foods like asam laksa and belacan fried rice seemed to discourage discretionary salt use. In conclusion, the preference and intake frequency of the high sodium belacan-based dish asam laksa seems to be a good predictor for ethnic

  10. Combined approach for finding susceptibility genes in DISH/chondrocalcinosis families: whole-genome-wide linkage and IBS/IBD studies.

    Science.gov (United States)

    Couto, Ana Rita; Parreira, Bruna; Thomson, Russell; Soares, Marta; Power, Deborah M; Stankovich, Jim; Armas, Jácome Bruges; Brown, Matthew A

    2017-01-01

    Twelve families with exuberant and early-onset calcium pyrophosphate dehydrate chondrocalcinosis (CC) and diffuse idiopathic skeletal hyperostosis (DISH), hereafter designated DISH/CC, were identified in Terceira Island, the Azores, Portugal. Ninety-two (92) individuals from these families were selected for whole-genome-wide linkage analysis. An identity-by-descent (IBD) analysis was performed in 10 individuals from 5 of the investigated pedigrees. The chromosome area with the maximal logarithm of the odds score (1.32; P =0.007) was not identified using the IBD/identity-by-state (IBS) analysis; therefore, it was not investigated further. From the IBD/IBS analysis, two candidate genes, LEMD3 and RSPO4 , were identified and sequenced. Nine genetic variants were identified in the RSPO4 gene; one regulatory variant (rs146447064) was significantly more frequent in control individuals than in DISH/CC patients ( P =0.03). Four variants were identified in LEMD3 , and the rs201930700 variant was further investigated using segregation analysis. None of the genetic variants in RSPO4 or LEMD3 segregated within the studied families. Therefore, although a major genetic effect was shown to determine DISH/CC occurrence within these families, the specific genetic variants involved were not identified.

  11. Prevalence of diffuse idiopathic skeletal hyperostosis (DISH) of the whole spine and its association with lumbar spondylosis and knee osteoarthritis: the ROAD study.

    Science.gov (United States)

    Kagotani, Ryohei; Yoshida, Munehito; Muraki, Shigeyuki; Oka, Hiroyuki; Hashizume, Hiroshi; Yamada, Hiroshi; Enyo, Yoshio; Nagata, Keiji; Ishimoto, Yuyu; Teraguchi, Masatoshi; Tanaka, Sakae; Nakamura, Kozo; Kawaguchi, Hiroshi; Akune, Toru; Yoshimura, Noriko

    2015-03-01

    We aimed to assess the prevalence of diffuse idiopathic skeletal hyperostosis (DISH) and its association with lumbar spondylosis (LS) and knee osteoarthritis (KOA) using a population-based cohort study entitled Research on Osteoarthritis/osteoporosis Against Disability (ROAD). In the baseline ROAD study, which was performed between 2005 and 2007, 1,690 participants in mountainous and coastal areas underwent anthropometric measurements and radiographic examinations of the whole spine (cervical, thoracic, and lumbar) and both knees. They also completed an interviewer-administered questionnaire. Presence of DISH was diagnosed according to Resnick criteria, and LS and KOA were defined as Kellgren-Lawrence (KL) grade ≥3. Among the 1,690 participants, whole-spine radiographs of 1,647 individuals (97.5%; 573 men, 1,074 women; mean age, 65.3 years) were evaluated. Prevalence of DISH was 10.8% (men 22.0%, women 4.8%), and was significantly higher in older participants (presence of DISH 72.3 years, absence of DISH 64.4 years) and mainly distributed at the thoracic spine (88.7%). Logistic regression analysis revealed that presence of DISH was significantly associated with older age [+1 year, odds ratio (OR): 1.06, 95% confidence interval (CI): 1.03-1.14], male sex (OR: 5.55, 95% CI: 3.57-8.63), higher body mass index (+1 kg/m(2), OR: 1.08, 95% CI: 1.02-1.14), presence of LS (KL2 vs KL0: 1, OR: 5.50, 95% CI: 2.81-10.8) (KL ≥3 vs KL0: 1, OR: 4.09, 95% CI: 2.08-8.03), and presence of KOA (KL ≥3 vs KL0: 1, OR: 1.89, 95% CI: 1.14-3.10) after adjusting for smoking, alcohol consumption, and residential area (mountainous vs coastal). This cross-sectional population-based study clarified the prevalence of DISH in general inhabitants and its significant association with LS and severe KOA.

  12. Association between Motives for Dish Choices during Home Meal Preparation and Weight Status in the NutriNet-Santé Study

    Directory of Open Access Journals (Sweden)

    Pauline Ducrot

    2016-07-01

    Full Text Available Although home cooking has been associated with a lower body mass index in a few studies, no data exists on the motives behind food dish choices during home meal preparation and on their association with overweight. This study aimed to evaluate this association in 50,003 participants from the NutriNet-Santé cohort. Dimensions underlying the importance of 27 criteria possibly influencing dish choices were determined using an exploratory factor analysis. The association between dish choice motives and overweight (including obesity was estimated using logistic regression models adjusted for sociodemographic and lifestyle characteristics. Five dimensions of dishes choice motives emerged: healthy diet (e.g., “nutritional balance of the dish”, constraints (e.g., “my cooking skills”, pleasure (e.g., “originality of the dish”, specific diets (e.g., “my health status”, and organization (e.g., “what I planned to eat”. A negative association was observed between the healthy diet factor and being overweight (OR = 0.65 (95% CI (confidence interval: 0.62–0.67, whereas a positive association appeared for factors regarding pleasure (OR = 1.14 (95% CI: 1.10–1.19 and specific diets (OR = 1.19 (95% CI: 1.17–1.22. No significant associations were observed for constraints and organization. The significant associations between dish choice motives and overweight suggested the interest of focusing on these motives in order to promote healthier food choices during home cooking.

  13. A Dish-based Semi-quantitative Food Frequency Questionnaire for Assessment of Dietary Intakes in Epidemiologic Studies in Iran: Design and Development.

    Science.gov (United States)

    Keshteli, Ah; Esmaillzadeh, Ahmad; Rajaie, Somayeh; Askari, Gholamreza; Feinle-Bisset, Christine; Adibi, Peyman

    2014-01-01

    Earlier forms of food frequency questionnaire (FFQ) used in Iran have extensive lists of foods, traditional categories and food-based design, mostly with the interviewer-administered approach. The aim of the current paper is to describe the development of a dish-based, machine-readable, semi-quantitative food frequency questionnaire (DFQ). Within the framework of the Study on the Epidemiology of Psychological, Alimentary Health and Nutrition project, we created a novel FFQ using Harvard FFQ as a model. THE FOLLOWING STEPS WERE TAKEN TO DEVELOP THE QUESTIONNAIRE: Construction of a list of commonly consumed Iranian foods, definition of portion sizes, design of response options for consumption frequency of each food item and finally a pilot test of the preliminary DFQ. From a comprehensive list of foods and mixed dishes, we included those that were nutrient-rich, consumed reasonably often or contributed to between-person variations. We focused on mixed dishes, rather than their ingredients, along with foods. To shorten the list, the related food items or mixed dishes were categorized together in one food group. These exclusions resulted in a list of 106 foods or dishes in the questionnaire. The portion sizes used in the FFQ were obtained from our earlier studies that used dietary recalls and food records. The frequency response options for the food list varied from 6-9 choices from "never or less than once a month" to "12 or more times per day". The DFQ could be a reasonable dietary assessment tool for future epidemiological studies in the country. Validation studies are required to assess the validity and reliability of this newly developed questionnaire.

  14. A Dish-based Semi-quantitative food frequency questionnaire for assessment of dietary intakes in epidemiologic studies in Iran: Design and development

    Directory of Open Access Journals (Sweden)

    Ammar Hassanzadeh Keshteli

    2014-01-01

    Full Text Available Background: Earlier forms of food frequency questionnaire (FFQ used in Iran have extensive lists of foods, traditional categories and food-based design, mostly with the interviewer-administered approach. The aim of the current paper is to describe the development of a dish-based, machine-readable, semi-quantitative food frequency questionnaire (DFQ. Methods: Within the framework of the Study on the Epidemiology of Psychological, Alimentary Health and Nutrition project, we created a novel FFQ using Harvard FFQ as a model. Results: The following steps were taken to develop the questionnaire: Construction of a list of commonly consumed Iranian foods, definition of portion sizes, design of response options for consumption frequency of each food item and finally a pilot test of the preliminary DFQ. From a comprehensive list of foods and mixed dishes, we included those that were nutrient-rich, consumed reasonably often or contributed to between-person variations. We focused on mixed dishes, rather than their ingredients, along with foods. To shorten the list, the related food items or mixed dishes were categorized together in one food group. These exclusions resulted in a list of 106 foods or dishes in the questionnaire. The portion sizes used in the FFQ were obtained from our earlier studies that used dietary recalls and food records. The frequency response options for the food list varied from 6-9 choices from "never or less than once a month" to "12 or more times per day". Conclusions: The DFQ could be a reasonable dietary assessment tool for future epidemiological studies in the country. Validation studies are required to assess the validity and reliability of this newly developed questionnaire.

  15. Innovative Application of Maintenance-Free Phase-Change Thermal Energy Storage for Dish-Engine Solar Power Generation

    Energy Technology Data Exchange (ETDEWEB)

    Qui, Songgang [Temple University; Galbraith, Ross [Infinia

    2013-01-23

    This final report summarizes the final results of the Phase II Innovative Application of Maintenance-Free Phase-Change Thermal Energy Storage for Dish-Engine Solar Power Generation project being performed by Infinia Corporation for the U.S. Department of Energy under contract DE-FC36-08GO18157 during the project period of September 1, 2009 - August 30, 2012. The primary objective of this project is to demonstrate the practicality of integrating thermal energy storage (TES) modules, using a suitable thermal salt phase-change material (PCM) as its medium, with a dish/Stirling engine; enabling the system to operate during cloud transients and to provide dispatchable power for 4 to 6 hours after sunset. A laboratory prototype designed to provide 3 kW-h of net electrical output was constructed and tested at Infinia's Ogden Headquarters. In the course of the testing, it was determined that the system's heat pipe network - used to transfer incoming heat from the solar receiver to both the Stirling generator heater head and to the phase change salt - did not perform to expectations. The heat pipes had limited capacity to deliver sufficient heat energy to the generator and salt mass while in a charging mode, which was highly dependent on the orientation of the device (vertical versus horizontal). In addition, the TES system was only able to extract about 30 to 40% of the expected amount of energy from the phase change salt once it was fully molten. However, the use of heat pipes to transfer heat energy to and from a thermal energy storage medium is a key technical innovation, and the project team feels that the limitations of the current device could be greatly improved with further development. A detailed study of manufacturing costs using the prototype TES module as a basis indicates that meeting DOE LCOE goals with this hardware requires significant efforts. Improvement can be made by implementing aggressive cost-down initiatives in design and materials

  16. Preliminary designs for 25 kWe advanced Stirling conversion systems for dish electric applications

    Science.gov (United States)

    Shaltens, Richard K.; Schreiber, Jeffrey G.

    Under the Department of Energy's (DOE) Solar Thermal Technology Program, Sandia National Laboratories is evaluating heat engines for terrestrial Solar Distributed Heat Receivers. The Stirling engine has been identified by Sandia as one of the most promising engines for terrestrial applications. The Stirling engine also has the potential to meet DOE's performance and cost goals. The NASA Lewis Research Center is conducting Stirling engine technology development activities directed toward a dynamic power source for space applications. Space power systems requirements include high reliability, very long life, low vibration and high efficiency. The free-piston Stirling engine has the potential for future high power space conversion systems, either nuclear or solar powered. Although both applications appear to be quite different, their requirements complement each other. Preliminary designs feature a free-piston Stirling engine, a liquid metal heat transport system, and a means to provide nominally 25 kW electric power to a utility grid while meeting DOE's performance and long term cost goals. The Cummins design incorporates a linear alternator to provide the electrical output, while the STC design generates electrical power indirectly through a hydraulic pump/motor coupled to an induction generator. Both designs for the ASCS's will use technology which can reasonably be expected to be available in the early 1990's.

  17. Programming

    International Nuclear Information System (INIS)

    Jackson, M.A.

    1982-01-01

    The programmer's task is often taken to be the construction of algorithms, expressed in hierarchical structures of procedures: this view underlies the majority of traditional programming languages, such as Fortran. A different view is appropriate to a wide class of problem, perhaps including some problems in High Energy Physics. The programmer's task is regarded as having three main stages: first, an explicit model is constructed of the reality with which the program is concerned; second, this model is elaborated to produce the required program outputs; third, the resulting program is transformed to run efficiently in the execution environment. The first two stages deal in network structures of sequential processes; only the third is concerned with procedure hierarchies. (orig.)

  18. Programming

    OpenAIRE

    Jackson, M A

    1982-01-01

    The programmer's task is often taken to be the construction of algorithms, expressed in hierarchical structures of procedures: this view underlies the majority of traditional programming languages, such as Fortran. A different view is appropriate to a wide class of problem, perhaps including some problems in High Energy Physics. The programmer's task is regarded as having three main stages: first, an explicit model is constructed of the reality with which the program is concerned; second, thi...

  19. Phage-mediated counting by the naked eye of miRNA molecules at attomolar concentrations in a Petri dish

    Science.gov (United States)

    Zhou, Xin; Cao, Peng; Zhu, Ye; Lu, Wuguang; Gu, Ning; Mao, Chuanbin

    2015-10-01

    The ability to count biomolecules such as cancer-biomarker miRNAs with the naked eye is seemingly impossible in molecular diagnostics. Here, we show an ultrasensitive naked-eye-counting strategy for quantifying miRNAs by employing T7 phage--a bacteria-specific virus nanoparticle--as a surrogate. The phage is genetically engineered to become fluorescent and capable of binding a miRNA-capturing gold nanoparticle (GNP) in a one-to-one manner. Target miRNAs crosslink the resultant phage-GNP couple and miRNA-capturing magnetic microparticles, forming a sandwich complex containing equimolar phage and miRNA. The phage is then released from the complex and developed into one macroscopic fluorescent plaque in a Petri dish by plating it in a host bacterial medium. Counting the plaques by the naked eye enables the quantification of miRNAs with detection limits of ~3 and ~5 aM for single-target and two-target miRNAs, respectively. This approach offers ultrasensitive and convenient quantification of disease biomarkers by the naked eye.

  20. Effect of lime juice on Vibrio parahaemolyticus and Salmonella enterica inactivation during the preparation of the raw fish dish ceviche.

    Science.gov (United States)

    Mathurand, Prateek; Schaffner, Donald W

    2013-06-01

    Ceviche is a raw fish dish common in Peru and other Latin American counties. The most characteristic feature of ceviche is the use of lime juice for marinating or "cooking" the raw fish. Confirmed cases of cholera in Peru, New Jersey, and Florida have been associated with ceviche. Although the effect of organic acids on pathogenic bacteria has been well characterized, few data exist on the effect of these acids in seafood systems. The objective of the study was to evaluate the effects of lime juice marination on pathogens likely to be present in ceviche. Tilapia (Oreochromis niloticus) fillet pieces were inoculated with Vibrio parahaemolyticus and Salmonella enterica (>7 log CFU/g) and incubated at 25 and 4°C for 30 or 120 min in the presence of fresh lime juice at concentrations typical for the preparation of ceviche. Similar levels of cells were also inoculated into fresh lime juice without tilapia. Surviving cells were enumerated on selective (xylose lysine Tergitol 4 and thiosulfate-bile-citrate-sucrose) and nonselective (tryptic soy agar) media. V. parahaemolyticus levels were reduced to below detection limits (∼5-log reduction) under all conditions studied. Salmonella strains on tilapia were much more resistant to inactivation and were only slightly reduced (∼1- to 2-log reduction). Salmonella and V. parahaemolyticus inoculated directly into lime juice without tilapia were all reduced to below detection limits (∼5-log reduction). A typical ceviche recipe reduces V. parahaemolyticus risk significantly but is less effective for control of S. enterica.

  1. Liquid dish washing soap: An excellent substitute for xylene and alcohol in hematoxylin and eosin staining procedure

    Directory of Open Access Journals (Sweden)

    Surekha Ramulu

    2012-01-01

    Full Text Available Aims: Liquid dish washing solution (DWS was used as a substitute for xylene to dewax tissue sections during hematoxylin and eosin (H and E staining. The aim was to test and compare the hypothesis that xylene-ethanol free (XEF sections deparaffinized with diluted DWS are better than or at par with the conventional H and E sections. Materials and Methods: Fifty paraffin-embedded tissue blocks was included. One section was stained with conventional HandE (group A and the other with XEF HandE (group B staining method. Slides were scored for parameters: nuclear, cytoplasmic, clarity, uniformity, and crispness of staining. Z test was used for statistical analysis. For accuracy of diagnosis, sensitivity, specificity, positive predictive value, and negative predictive value were tested. Results: Adequate nuclear staining was noted in 94% in group A and 96% in group B, -adequate cytoplasmic staining in 92% in group A and 86% in group B, clarity in 94% of group A and 96% of group B sections, uniform staining in 92% of group A and 80% of group B sections, crisp stain in 96% of group A and 88% of group B sections, and 94% of group A sections stained adequately for diagnosis as compared with 90% in group B sections. Conclusion: Liquid DWS can be used as an alternative and effective substitute to xylene and ethanol in routine HandE staining procedure.

  2. Disease-in-a-dish: the contribution of patient-specific induced pluripotent stem cell technology to regenerative rehabilitation.

    Science.gov (United States)

    Mack, David L; Guan, Xuan; Wagoner, Ashley; Walker, Stephen J; Childers, Martin K

    2014-11-01

    Advances in regenerative medicine technologies will lead to dramatic changes in how patients in rehabilitation medicine clinics are treated in the upcoming decades. The multidisciplinary field of regenerative medicine is developing new tools for disease modeling and drug discovery based on induced pluripotent stem cells. This approach capitalizes on the idea of personalized medicine by using the patient's own cells to discover new drugs, increasing the likelihood of a favorable outcome. The search for compounds that can correct disease defects in the culture dish is a conceptual departure from how drug screens were done in the past. This system proposes a closed loop from sample collection from the diseased patient, to in vitro disease model, to drug discovery and Food and Drug Administration approval, to delivering that drug back to the same patient. Here, recent progress in patient-specific induced pluripotent stem cell derivation, directed differentiation toward diseased cell types, and how those cells can be used for high-throughput drug screens are reviewed. Given that restoration of normal function is a driving force in rehabilitation medicine, the authors believe that this drug discovery platform focusing on phenotypic rescue will become a key contributor to therapeutic compounds in regenerative rehabilitation.

  3. Formation of dish-like holes and a channel structure in electrodeposition of copper under hydrogen co-deposition

    International Nuclear Information System (INIS)

    Nikolic, N.D.; Pavlovic, Lj.J.; Pavlovic, M.G.; Popov, K.I.

    2007-01-01

    Copper electrodeposition from acid sulfate solutions at an overpotential of 1000 mV, which is about 250 mV outside the plateau of the limiting diffusion current density, was examined by the determination of the average current efficiency of hydrogen evolution and by the scanning electron microscopic (SEM) analysis of the morphology of the formed copper deposits. Craters or holes formed due to the attachment hydrogen bubbles were the dominant morphological forms of copper deposits obtained at this overpotential. In dependence of the concentration of Cu (II) ions in the plating solution, the two types of holes or craters were formed. One type of holes is obtained by electrodeposition from a solution with a concentration of Cu (II) ions of 0.075 M CuSO 4 in 0.50 M H 2 SO 4 , and a honeycomb-like structure was formed from these holes. The other types of holes are formed from a solution with a higher concentration of Cu (II) ions (0.60 M CuSO 4 in 0.50 M H 2 SO 4 ) and the formed holes were dish-like. A mixture of both types of holes was obtained by electrodeposition from 0.30 M CuSO 4 in 0.50 M H 2 SO 4 . The obtained morphologies of copper deposits are discussed in terms of the effect of hydrogen evolution on the hydrodynamic conditions in the plating solution

  4. Studying effects of Magnolol on alpha-particle induced bystander effects using PADC-film based dishes

    International Nuclear Information System (INIS)

    Wong, T.P.W.; Tse, A.K.W.; Fong, W.F.; Yu, K.N.

    2009-01-01

    Radiation-induced bystander effect refers to the biological response found in cells (called bystander cells) which are not irradiated directly by ionizing radiation but are next to cells irradiated directly by ionizing radiation. In the present paper, the effects of Magnolol, an extract from the bark of Magnolia officinalis which is used as a traditional Chinese medicine, were studied on alpha-particle induced bystander effects. In our experiments, Chinese hamster ovary (CHO) cells were cultured in PADC-film based dishes and were irradiated with low fluences of alpha particles passing through the PADC films. The precise number of cells traversed or missed by alpha particles could be determined by studying the alpha-particle tracks developed on the PADC films upon subsequent chemical etching. TdT-mediated dUTP Nick-End Labeling (TUNEL) assay was employed to analyze the biological response of bystander cells in terms of DNA strand breaks. With the pretreatment of Magnolol, the DNA strand breaks in bystander cells were reduced, which showed that the alpha-particle induced bystander effects were suppressed with the presence of Magnolol. Since Magnolol is an antioxidant which can scavenge reactive oxygen species (ROS), our results give support to that ROS play a role in the bystander signal transmission in our experiments.

  5. Studying effects of Magnolol on alpha-particle induced bystander effects using PADC-film based dishes

    Energy Technology Data Exchange (ETDEWEB)

    Wong, T.P.W. [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon Tong (Hong Kong); Tse, A.K.W.; Fong, W.F. [Research and Development Division, School of Chinese Medicine, Hong Kong Baptist University, Baptist University Road, Kowloon Tong (Hong Kong); Yu, K.N., E-mail: peter.yu@cityu.edu.h [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon Tong (Hong Kong)

    2009-10-15

    Radiation-induced bystander effect refers to the biological response found in cells (called bystander cells) which are not irradiated directly by ionizing radiation but are next to cells irradiated directly by ionizing radiation. In the present paper, the effects of Magnolol, an extract from the bark of Magnolia officinalis which is used as a traditional Chinese medicine, were studied on alpha-particle induced bystander effects. In our experiments, Chinese hamster ovary (CHO) cells were cultured in PADC-film based dishes and were irradiated with low fluences of alpha particles passing through the PADC films. The precise number of cells traversed or missed by alpha particles could be determined by studying the alpha-particle tracks developed on the PADC films upon subsequent chemical etching. TdT-mediated dUTP Nick-End Labeling (TUNEL) assay was employed to analyze the biological response of bystander cells in terms of DNA strand breaks. With the pretreatment of Magnolol, the DNA strand breaks in bystander cells were reduced, which showed that the alpha-particle induced bystander effects were suppressed with the presence of Magnolol. Since Magnolol is an antioxidant which can scavenge reactive oxygen species (ROS), our results give support to that ROS play a role in the bystander signal transmission in our experiments.

  6. Effect of the phase change material in a solar receiver on thermal performance of parabolic dish collector

    Directory of Open Access Journals (Sweden)

    Senthil Ramalingam

    2017-01-01

    Full Text Available In this work, the use of phase change material in the circular tank solar receiver is proposed for a 16 m2 Scheffler parabolic dish solar concentrator to improve the heat transfer in the receiver. Magnesium chloride hexahydrate with melting temperature of 117°C is selected as the phase change material in the annular space of the receiver with rectangular fins inside the phase change material. Experimental work is carried out to analyze heat transfer from the receiver to heat transfer fluid with and without phase change material in the inner periphery. Energy and exergy efficiency are determined from the measurements of solar radiation intensity, receiver temperature, surroundings temperature, heat transfer fluid inlet and outlet temperatures, storage tank temperature, and wind speed. The experiments were conducted in SRM University, Chennai, India (latitude: 13° 5′ N, longitude: 80°16′ E in April 2014. Use of phase change material in receiver periphery increased energy efficiency by 5.62%, exergy efficiency by 12.8% and decreased time to reach the boiling point of water by 20% when compared with the receiver without phase change material.

  7. Performance analysis of dish solar stirling power system; Stirling engine wo mochiita taiyonetsu hatsuden system no seino yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Tsuchiya, K; Yamaguchi, I [Meiji University, Tokyo (Japan); Naito, Y; Momose, Y [Aisin Seiki Co. Ltd., Aichi (Japan)

    1996-10-27

    In order to estimate the performance of the dish solar Stirling power system, matching and control of each component system were studied, and the performance of the 25kWe class power system was estimated on the basis of direct solar radiation measured in Miyako island, Okinawa. Application of a Stirling engine to solar heat power generation is highly effective in spite of its small scale. The total system is composed of a converging system, heat receiver, engine/generator system and control system. As the simulation result, the generator output is nearly proportional to direct solar radiation, and the system efficiency approaches to a certain constant value with an increase in direct solar radiation. As accumulated solar radiation is large, the influence of slope error of the converging mirror is comparatively small. The optimum aperture opening ratio of the heat receiver determined on the basis of mean direct solar radiation (accumulated solar radiation/{Delta}t (simulated operation time of the system)), corresponds to the primary approximation of the opening ratio for a maximum total generated output under variable direct solar radiation. 6 refs., 6 figs., 1 tab.

  8. Solar reforming of methane in a direct absorption catalytic reactor on a parabolic dish. 2: Modeling and analysis

    Science.gov (United States)

    Skocypec, Russell D.; Hogan, Roy E., Jr.; Muir, James F.

    1991-01-01

    The catalytically enhanced solar absorption receiver (CAESAR) experiment was conducted to determine the thermal, chemical, and mechanical performance of a commercial-scale, dish-mounted, direct catalytic absorption receiver (DCAR) reactor over a range of steady state and transient (cloud) operating conditions. The focus of the experiment is on global performance such as receiver efficiencies and overall methane conversion; it was not intended to provide data for code validation. A numerical model was previously developed to provide guidance in the design of the absorber. The one-dimensional, planar and steady-state model incorporates, the following energy transfer mechanisms: solar and infrared radiation, heterogeneous chemical reaction, conduction in the solid phase, and convection between the fluid and solid phases. A number of upgrades to the model and improved property values are presented here. Model predictions are shown to bound the experimental axial thermocouple data when experimental uncertainties are included. Global predictions are made using a technique in which the incident solar flux distribution is subdivided into flux contour bands. Model predictions for each band are then spatially integrated to provide global predictions such as reactor efficiencies and methane conversions. Global predictions are shown to compare well with experimental data. Reactor predictions for anticipated operating conditions suggest a further decrease in optical density at the front of the absorber inner disk may be beneficial. The need to conduct code-validation experiments is identified as being essential in improving the confidence in the capability to predict large-scale reactor operation.

  9. A Dish-based Semi-quantitative food frequency questionnaire for assessment of dietary intakes in epidemiologic studies in Iran: Design and development

    OpenAIRE

    Ammar Hassanzadeh Keshteli; Ahmad Esmaillzadeh; Somayeh Rajaie; Gholamreza Askari; Christine Feinle-Bisset; Peyman Adibi

    2014-01-01

    Background: Earlier forms of food frequency questionnaire (FFQ) used in Iran have extensive lists of foods, traditional categories and food-based design, mostly with the interviewer-administered approach. The aim of the current paper is to describe the development of a dish-based, machine-readable, semi-quantitative food frequency questionnaire (DFQ). Methods: Within the framework of the Study on the Epidemiology of Psychological, Alimentary Health and Nutrition project, we created a nove...

  10. Associations between motives for dish choice during home-meal preparation and diet quality in French adults: findings from the NutriNet-Santé study.

    Science.gov (United States)

    Ducrot, Pauline; Méjean, Caroline; Fassier, Philippine; Allès, Benjamin; Hercberg, Serge; Péneau, Sandrine

    2017-03-01

    A number of motives such as constraints or pleasure have been suggested to influence dish choices during home-meal preparation. However, no study has evaluated how the importance conferred to these motives potentially influence diet quality. The present study aims at investigating the difference in diet quality according to the importance attached by individuals to various dish choice motives. The importance of twenty-seven criteria related to dish choices on weekdays was evaluated among 48 010 French adults from the NutriNet-Santé study. ANCOVA and logistic regression models, adjusted for sociodemographic and lifestyle factors, were used to evaluate the association between the importance attached to dish choice motives (yes v. no) and energy and food group intakes, as well as adherence to French nutritional guidelines (modified Programme National Nutrition Santé-Guideline Score (mPNNS-GS)). A higher adherence to nutritional guidelines was observed in individuals attaching importance to a healthy diet (mPNNS-GS score 7·87 (sd 0·09) v. 7·39 (sd 0·09)) and specific diets (mPNNS-GS score 7·73 (sd 0·09) v. 7·53 (sd 0·09)), compared with those who attached little/no importance (all Pfoods compared with their respective counterparts (all Pmotives, that is, constraints, pleasure and organisation, only small differences were observed. The main difference in diet quality was related to the importance placed on a healthy diet. Although a causal link should be demonstrated, our findings suggested that strategies aiming at enabling people to take into account diet quality during home-meal preparation might be effective levers to promote healthy eating.

  11. The NOD3 software package: A graphical user interface-supported reduction package for single-dish radio continuum and polarisation observations

    Science.gov (United States)

    Müller, Peter; Krause, Marita; Beck, Rainer; Schmidt, Philip

    2017-10-01

    Context. The venerable NOD2 data reduction software package for single-dish radio continuum observations, which was developed for use at the 100-m Effelsberg radio telescope, has been successfully applied over many decades. Modern computing facilities, however, call for a new design. Aims: We aim to develop an interactive software tool with a graphical user interface for the reduction of single-dish radio continuum maps. We make a special effort to reduce the distortions along the scanning direction (scanning effects) by combining maps scanned in orthogonal directions or dual- or multiple-horn observations that need to be processed in a restoration procedure. The package should also process polarisation data and offer the possibility to include special tasks written by the individual user. Methods: Based on the ideas of the NOD2 package we developed NOD3, which includes all necessary tasks from the raw maps to the final maps in total intensity and linear polarisation. Furthermore, plot routines and several methods for map analysis are available. The NOD3 package is written in Python, which allows the extension of the package via additional tasks. The required data format for the input maps is FITS. Results: The NOD3 package is a sophisticated tool to process and analyse maps from single-dish observations that are affected by scanning effects from clouds, receiver instabilities, or radio-frequency interference. The "basket-weaving" tool combines orthogonally scanned maps into a final map that is almost free of scanning effects. The new restoration tool for dual-beam observations reduces the noise by a factor of about two compared to the NOD2 version. Combining single-dish with interferometer data in the map plane ensures the full recovery of the total flux density. Conclusions: This software package is available under the open source license GPL for free use at other single-dish radio telescopes of the astronomical community. The NOD3 package is designed to be

  12. Performance evaluation of a stand-alone solar dish Stirling system for power generation suitable for off-grid rural electrification

    International Nuclear Information System (INIS)

    Kadri, Y.; Hadj Abdallah, H.

    2016-01-01

    Highlights: • Estimation of the output temperature reached by 2 m parabolic dish. • Output power estimation for uncontrollable load was done using Matlab®. • Validation of the proposed system under Tunisian conditions for rural electrification. - Abstract: The development of green power generation such as solar systems that have become a great interest for several countries especially for Tunisia as it presents a significant solar potential. For this purpose, this research has investigated the feasibility and the performance of standalone solar dish/Stirling micro generation plant for rural electrification. The considered hybrid system includes solar dish/Stirling engine, permanent magnet synchronous generator and a storage battery. To start with, thermal modeling and simulation have been carried out using Matlab® for the solar-driven Stirling heat engine system composed of an Alpha Stirling engine, a solar collector and a receiver, in which the radiation, convection, conduction and radiation heat loss have been taken into consideration for the selected design. For numerical validation of the receiver’s thermal model, simulation results were compared with experimental measurements reported for the EURODISH system with a reasonable degree of agreement. Second, the generated torque driving the generator has been estimated by the Adiabatic model of URIELI based on the classical fourth-order Runge-Kutta. In order for an autonomous control, the dish generator is connected to the load via power electronic converters where the bidirectional power flow is possible by the use of two voltage source converters in a back-to-back configuration. They are referred to as Stirling/generator side converter and load side inverter, both are oriented control by space vector pulse width modulation. In this context, the Stirling side converter is used to adjust the synchronous generator while the inverter controls the power flow between the direct current bus and the

  13. Psychiatry in a Dish

    DEFF Research Database (Denmark)

    Ilieva, Mirolyba; Fex Svenningsen, Åsa; Thorsen, Morten

    2018-01-01

    , disturbances in cell-cell communication, and an unbalanced ratio between certain neuronal populations. All those processes are highly dependent on the interconnectivity and three-dimensional organizations of the brain. Moreover, in order to gain a deeper understanding of the complex neurobiology of autism......Autism spectrum disorders are a group of pervasive neurodevelopmental conditions with heterogeneous etiology, characterized by deficits in social cognition, communication, and behavioral flexibility. Despite an increasing scientific effort to find the pathophysiological explanations for the disease...

  14. From soil to dish

    International Nuclear Information System (INIS)

    Preuthun, J.; Brink, M.; Rantavaara, A.; Runolfsson, H.; Salbu, B.

    1997-12-01

    EKO-3,4 is the first step towards a regular Nordic cooperation within nuclear emergency preparedness in the area of agriculture and foodstuffs. A collective Nordic handbook concerning limitation of nuclear release consequences in agriculture and food products is in preparation. Maximum permissible doses in foodstuffs, administrative procedures in case of a nuclear accident, the communication system among the respective national emergency centers, are a few examples of problems the handbook would cover. (EG)

  15. The Comparison of Photovoltaic with Small Solar Dish Stirling for Solar Home System 50 W{sub p} in Thailand, Medium Insolation Nature

    Energy Technology Data Exchange (ETDEWEB)

    Snidvongs, E. S.; Jindaruj, S.

    2006-07-01

    The Thai government initiated a project entitled Solar Home System which involved the provision of standalone Photovoltaic 50 Wp for houses without transmission lines in remote areas, 300,000 units. These units are provided at a low price with the government supporting half of the cost and the rest paid by the owners in installments. So far, more than 150,000 units have been installed and it is expected that the whole project would be completed by the end of the year 2005. A purpose of this research is to compare the original Thai government's Solar Home PV System with the new 50 Wp Small Solar Thermal Dish Stirling System in terms of their advantages and disadvantages for Thailand. The result of this would serve as a guide for the users to select the most suitable system in terms of price, maintenance, cost, economy, performance, reliability, and efficiency. Such comparison will be presented in the form of descriptive, photographs, statistics, and tables. As for the data involved, part of this is based on active fact such as construction cost, material cost, labor cost, rate of inflation, rate of interest. While some of these derives from the experience of researcher as well as facts and figures from Thai governments publications such as operation and maintenance cost. In addition to that some data are taken from basic experiments conducted either by the various universities and the researcher own laboratory. These include solar insolation, PV data and Stirling engine test with electric heater. And, of course, some data are based on simple estimation and prediction. Thailand is a country of 550 w/m2 with high humidity, soft-land and medium insolation. It locates near the equator at latitude 5 12 N, longitude 96 106 E. By using a parabolic shape satellite dish with solar tracker and a 60 W Four Cylinders gamma type Stirling engine with sinusoidal gear linear link, low offset space, and solid thermal storage to act as buffer between the solar energy and the

  16. Manufacturing cost analysis of a parabolic dish concentrator (General Electric design) for solar thermal electric power systems in selected production volumes

    Science.gov (United States)

    1981-01-01

    The manufacturing cost of a General Electric 12 meter diameter concentrator was estimated. This parabolic dish concentrator for solar thermal system was costed in annual production volumes of 100 - 1,000 - 5,000 - 10,000 - 50,000 100,000 - 400,000 and 1,000,000 units. Presented for each volume are the costs of direct labor, material, burden, tooling, capital equipment and buildings. Also presented is the direct labor personnel and factory space requirements. All costs are based on early 1981 economics.

  17. Enumeration of Salmonellae in Table Eggs, Pasteurized Egg Products, and Egg-Containing Dishes by Using Quantitative Real-Time PCR

    DEFF Research Database (Denmark)

    Jakočiūnė, Džiuginta; Pasquali, Frédérique; da Silva, Cristiana Soares

    2014-01-01

    PCR) was employed for enumeration of salmonellae in different matrices: table eggs, pasteurized egg products, and egg-containing dishes. Salmonella enterica serovar Enteritidis and S. enterica serovar Tennessee were used to artificially contaminate these matrices. The results showed a linear regression between...... the numbers of salmonellae and the quantification cycle (Cq) values for all matrices used, with the exception of pasteurized egg white. Standard curves were constructed by using both stationary-phase cells and heat-stressed cells, with similar results. Finally, this method was used to evaluate the fate...

  18. Open-Ended Waveguide Measurement and Numerical Simulation of the Reflectivity of Petri Dish Supported Skin Cell Monolayers in the mm-wave Range

    Science.gov (United States)

    Beneduci, Amerigo; Chidichimo, Giuseppe

    2012-05-01

    Open-ended waveguide reflectometry is a promising tool for permittivity and other material properties calculation at mm-waves (30-300 GHz). Measurement of the reflection coefficient does not require sample manipulation, allowing in vivo and in vitro non destructive studies on cells. Here we used this technique for measuring the power reflection coefficient (reflectivity) of water and Petri dish supported human skin melanoma and keratinocyte cell cultures, in the 53-72 GHz frequency range. The dependence of the reflectivity on polystyrene or glass thickness of the Petri base plate and on the cell layer thickness was analyzed. Permittivity data were then easily retrieved by using a plane wave-dominant mode approach for formulating the reflectivity at the aperture of the flange-mounted open-ended rectangular waveguide probe. Limits and validity of such an approximate approach were analyzed and compared with full-wave near field formulations for which magnitude and phase of the reflection coefficient must be measured and solved using complicated systems of integral equations and extensive numerical calculation. Finally, Petri dish reflectivity measured by the open-ended waveguide method was compared with that numerically simulated under far-field exposure conditions used in a large number of in vitro studies. Such an analysis showed that, under certain conditions, open-ended reflectivity values approach the far field ones.

  19. Mean and peak wind load reduction on heliostats

    Energy Technology Data Exchange (ETDEWEB)

    Peterka, J.A.; Tan, L.; Bienkiewcz, B.; Cermak, J.E.

    1987-09-01

    This report presents the results of wind-tunnel tests supported through the Solar Energy Research Institute (SERI) by the Office of Solar Thermal Technology of the US Department of Energy as part of the SERI research effort on innovative concentrators. As gravity loads on drive mechanisms are reduced through stretched-membrane technology, the wind-load contribution of the required drive capacity increases in percentage. Reduction of wind loads can provide economy in support structure and heliostat drive. Wind-tunnel tests have been directed at finding methods to reduce wind loads on heliostats. The tests investigated both mean and peak forces, and moments. A significant increase in ability to predict heliostat wind loads and their reduction within a heliostat field was achieved. In addition, a preliminary review of wind loads on parabolic dish collectors was conducted, resulting in a recommended research program for these type collectors. 42 refs., 38 figs., 1 tab.

  20. Study on the radiation flux and temperature distributions of the concentrator-receiver system in a solar dish/Stirling power facility

    International Nuclear Information System (INIS)

    Li Zhigang; Tang Dawei; Du Jinglong; Li Tie

    2011-01-01

    Uniform heater temperature and high optical-thermal efficiency are crucial for the reliable and economical operation of a Solar Dish/Stirling engine facility. The Monte-Carlo ray-tracing method is utilized to predict the radiation flux distributions of the concentrator-receiver system. The ray-tracing method is first validated by experiment, then the radiation flux profiles on the solar receiver surface for faceted real concentrator and ideal paraboloidal concentrator, irradiated by Xe-arc lamps and real sun, for different aperture positions and receiver shapes are analyzed, respectively. The resulted radiation flux profiles are subsequently transferred to a CFD code as boundary conditions to numerically simulate the fluid flow and conjugate heat transfer in the receiver cavity by coupling the radiation, natural convection and heat conduction together, and the CFD method is also validated through experiment. The results indicate that a faceted concentrator in combination with a solar simulator composed of 12 Xe-arc lamps is advantageous to drive the solar Stirling engine for all-weather indoor tests. Based on the simulation results, a solar receiver-Stirling heater configuration is designed to achieve a considerably uniform temperature distribution on the heater head tubes while maintaining a high efficiency of 60.7%. - Highlights: → Radiation flux in Dish/Stirling system is analyzed by validated ray-tracing method. → Temperature field on the solar receiver is analyzed by a validated CFD method. → Effects of Xe-arc lamp solar simulator and faceted real concentrator are analyzed. → Effects of different receiver positions and receiver shapes are investigated. → A Stirling heater configuration is presented with uniform temperature field.

  1. Probabilistic risk model for staphylococcal intoxication from pork-based food dishes prepared in food service establishments in Korea.

    Science.gov (United States)

    Kim, Hyun Jung; Griffiths, Mansel W; Fazil, Aamir M; Lammerding, Anna M

    2009-09-01

    Foodborne illness contracted at food service operations is an important public health issue in Korea. In this study, the probabilities for growth of, and enterotoxin production by, Staphylococcus aureus in pork meat-based foods prepared in food service operations were estimated by the Monte Carlo simulation. Data on the prevalence and concentration of S. aureus as well as compliance to guidelines for time and temperature controls during food service operations were collected. The growth of S. aureus was initially estimated by using the U.S. Department of Agriculture's Pathogen Modeling Program. A second model based on raw pork meat was derived to compare cell number predictions. The correlation between toxin level and cell number as well as minimum toxin dose obtained from published data was adopted to quantify the probability of staphylococcal intoxication. When data gaps were found, assumptions were made based on guidelines for food service practices. Baseline risk model and scenario analyses were performed to indicate possible outcomes of staphylococcal intoxication under the scenarios generated based on these data gaps. Staphylococcal growth was predicted during holding before and after cooking, and the highest estimated concentration (4.59 log CFU/g for the 99.9th percentile value) of S. aureus was observed in raw pork initially contaminated with S. aureus and held before cooking. The estimated probability for staphylococcal intoxication was very low, using currently available data. However, scenario analyses revealed an increased possibility of staphylococcal intoxication when increased levels of initial contamination in the raw meat, andlonger holding time both before and after cooking the meat occurred.

  2. “A por gauchos in chiripá...”. Expresiones criollistas en el teatro ídish argentino (1910-1930

    Directory of Open Access Journals (Sweden)

    Susana Skura

    2014-06-01

    Full Text Available En Argentina, entre 1890 y 1920, se desarrolló el fenómeno criollista, consistente en la difusión del gusto por lo gaucho como moda popular de consumos y usos culturales. Coincidió con el auge del proceso inmigratorio y atravesó los debates sobre el primer nacionalismo cultural y los festejos del centenario patrio. A partir del reciente hallazgo de una colección de textos dramáticos escritos en ídish con abundantes préstamos del español rioplatense trasliterados, y reunidos por la Fundación Iwo de Buenos Aires, se explora la inclusión de prácticas y terminología de la cultura dominante en un teatro escrito y actuado en la lengua de inmigración, como un aspecto del proceso de transculturación de los inmigrantes ashkenazíes y de las primeras generaciones nacidas en las colonias agrícolas judías argentinas.

  3. A comparative study to evaluate liquid dish washing soap as an alternative to xylene and alcohol in deparaffinization and hematoxylin and eosin staining.

    Science.gov (United States)

    Pandey, Pinki; Dixit, Alok; Tanwar, Aparna; Sharma, Anuradha; Mittal, Sanjeev

    2014-07-01

    Our study presents a new deparaffinizing and hematoxylin and eosin (H and E) staining method that involves the use of easily available, nontoxic and eco-friendly liquid diluted dish washing soap (DWS) by completely eliminating expensive and hazardous xylene and alcohol from deparaffinizing and rehydration prior to staining, staining and from dehydration prior to mounting. The aim was to evaluate and compare the quality of liquid DWS treated xylene and alcohol free (XAF) sections with that of the conventional H and E sections. A total of 100 paraffin embedded tissue blocks from different tissues were included. From each tissue block, one section was stained with conventional H and E (normal sections) and the other with XAF H and E (soapy sections) staining method. Slides were scored using five parameters: Nuclear, cytoplasmic, clarity, uniformity, and crispness of staining. Z-test was used for statistical analysis. Soapy sections scored better for cytoplasmic (90%) and crisp staining (95%) with a statistically significant difference. Whereas for uniformity of staining, normal sections (88%) scored over soapy sections (72%) (Z = 2.82, P 0.05). Liquid DWS is a safe and efficient alternative to xylene and alcohol in deparaffinization and routine H and E staining procedure. We are documenting this project that can be used as a model for other histology laboratories.

  4. Mini-guts in a dish: Perspectives of adult Cystic Fibrosis (CF) patients and parents of young CF patients on organoid technology.

    Science.gov (United States)

    Boers, Sarah N; de Winter-de Groot, Karin M; Noordhoek, Jacquelien; Gulmans, Vincent; van der Ent, Cornelis K; van Delden, Johannes J M; Bredenoord, Annelien L

    2018-03-06

    Organoid technology enables the cultivation of human tissues in a dish. Its precision medicine potential could revolutionize the Cystic Fibrosis (CF) field. We provide a first thematic exploration of the patient perspective on organoid technology to set the further research agenda, which is necessary for responsible development of this ethically challenging technology. 23 semi-structured qualitative interviews with 14 Dutch adult CF patients and 12 parents of young CF patients to examine their experiences, opinions, and attitudes regarding organoid technology. Four themes emerged: (1) Respondents express a close as well as a distant relationship to organoids; (2) the open-endedness of organoid technology sparks hopes and concerns, (3) commercial use evokes cautiousness. (4) Respondents mention the importance of sound consent procedures, long-term patient engagement, responsible stewardship, and stringent conditions for commercial use. The precision medicine potential of organoid technology can only be realized if the patient perspective is taken adequately into account. Copyright © 2018 European Cystic Fibrosis Society. Published by Elsevier B.V. All rights reserved.

  5. Enhanced migration of murine fibroblast-like 3T3-L1 preadipocytes on type I collagen-coated dish is reversed by silibinin treatment.

    Science.gov (United States)

    Liu, Xiaoling; Xu, Qian; Liu, Weiwei; Yao, Guodong; Zhao, Yeli; Xu, Fanxing; Hayashi, Toshihiko; Fujisaki, Hitomi; Hattori, Shunji; Tashiro, Shin-Ichi; Onodera, Satoshi; Yamato, Masayuki; Ikejima, Takashi

    2018-04-01

    Migration of fibroblast-like preadipocytes is important for the development of adipose tissue, whereas excessive migration is often responsible for impaired adipose tissue related with obesity and fibrotic diseases. Type I collagen (collagen I) is the most abundant component of extracellular matrix and has been shown to regulate fibroblast migration in vitro, but its role in adipose tissue is not known. Silibinin is a bioactive natural flavonoid with antioxidant and antimetastasis activities. In this study, we found that type I collagen coating promoted the proliferation and migration of murine 3T3-L1 preadipocytes in a dose-dependent manner, implying that collagen I could be an extracellular signal. Regarding the mechanisms of collagen I-stimulated 3T3-L1 migration, we found that NF-κB p65 is activated, including the increased nuclear translocation of NF-κB p65 as well as the upregulation of NF-κB p65 phosphorylation and acetylation, accompanied by the increased expressions of proinflammatory factors and the generation of reactive oxygen species (ROS). Reduction of collagen I-enhanced migration of cells by treatment with silibinin was associated with suppression of NF-κB p65 activity and ROS generation, and negatively correlated with the increasing sirt1 expression. Taken together, the enhanced migration of 3T3-L1 cells induced on collagen I-coated dish is mediated by the activation of NF-κB p65 function and ROS generation that can be alleviated with silibinin by upregulation of sirt1, leading to the repression of NF-κB p65 function and ROS generation.

  6. Effects of Indole-3-Acetic Acid on Germination in Lead Polluted Petri Dish of Citrullus lanatus (Thunberg Matsumura and Nakai, Cucurbitaceae

    Directory of Open Access Journals (Sweden)

    Matthew Chidozie Ogwu

    2015-12-01

    Full Text Available Watermelon, Citrullus lanatus (Thunberg Matsumura and Nakai is a tropical fruit vegetable. Indole-3-acetic acid (IAA is a popular phytohormone while lead (Pb is a common environmental pollutant in urban and sub-urban centers. C. lanatus were obtained from Benin City with a view to study the effects of IAA on their germination in Pb polluted environment.  Germination percentage without IAA and Pb treatment in petri dish was significant after ten days. Hastened germination was observed when IAA and lead were used. About 100 % germination was recorded after seven days. This suggests that water melon seeds can initiate growth even in lead polluted environment. Optimum level of 5 ppm IAA with the different levels of lead treatments may be recommended. Most important was that higher concentrations of Pb in the control (without IAA did not inhibit seedling shoot nor root growth. Longest seedling shoot length (cm was 10.33 ± 1.24 and 12.13 ± 2.06 on the seventh and eighth day respectively with the combined treatment levels of 1 ppm IAA and 15 ppm Pb. On the ninth day, 15.27 ± 0.96 was obtained from 1 ppm IAA and 20 ppm Pb. Longest seedling root length (cm values were recorded from the combined treatment levels of 0 ppm IAA and 10 ppm Pb for the seventh (9.10 ± 0.47 and ninth (10.37 ± 1.81 day respectively and 0 ppm and 15 ppm Pb on the eighth (9.37 ± 0.84 day. Significant means were also obtained with the treatment level of 0 and 20 ppm IAA. This present study suggest the germination of C. lanatus under Pb polluted environment may be rescued with optimum IAA.

  7. Efficacy of 1.5% Dish Washing Solution and 95% Lemon Water in Substituting Perilous Xylene as a Deparaffinizing Agent for Routine H and E Staining Procedure: A Short Study

    Directory of Open Access Journals (Sweden)

    Anuradha Ananthaneni

    2014-01-01

    Full Text Available Aim. To assess the efficacy of dish washing solution and diluted lemon water in deparaffinizing sections during conventional hematoxylin and eosin staining technique. Objective. The objective is to utilize eco-friendly economical substitute for xylene. Materials and Methods. Using twenty paraffin embedded tissue blocks, three sections each were prepared. One section was stained with conventional H and E method (Group A and the other two sections with xylene-free (XF H and E (Groups B and C. Staining characteristics were compared with xylene and scoring was given. Total score of 3–5 was regarded as adequate for diagnosis and less than that inadequate for diagnosis. Statistical Analysis. Chi-square test, Kruskal Wallis ANOVA test, and Mann-Whitney U test were used. Results. Adequacy of nuclear staining, crispness, and staining for diagnosis were greater in both Groups A and C (100% than Group B (95%. Adequacy of cytoplasmic staining was similar in all the three groups (100%. Group B showed comparatively superior uniform staining and less retention of wax. Conclusion. Dish washing solution or diluted lemon water can be replaced for xylene as deparaffinizing agent in hematoxylin and eosin procedure.

  8. The comparison of two different embryo culture methods in the course of in vitro fertilization program.

    Directory of Open Access Journals (Sweden)

    Barbara Grzechocinska

    2008-04-01

    Full Text Available The objective of the study was to compare two different embryo culture methods in the course of in vitro fertilization program by means of fertilization rate, embryo development, total time and cost. 98 patients undergoing assisted reproduction procedures due to infertility were analyzed. The inclusion criteria for the study: first IVF-ET program, at least 10 MII oocytes, no indications for ICSI. Oocytes were divided into two study groups: group A- open culture (oocytes placed in four-well dishes together, then inseminated and cultured in successive wells and group B - a closed culture (oocytes placed in microdroplets, each embryo cultured separately. The fertilization rate was assessed around 18 hours from insemination. The embryos were classified into four classes. The best embryos were chosen for transfer. In the group A the fertilization rate obtained was lower than in group B (68% vs. 78%, respectively. The microdroplet culture required more time on the insemination day and on the second day of culture, while the four-well dish method required more time on the first day of culture and on the day of transfer. On analyzing the total cost of the above procedures (MI medium and oil costs it occurred that the microdroplet culture was more expensive than the four-well dish method (due to the intake of paraffin oil. However, the difference was of no practical importance. In the conclusion, microdroplet culture gives a higher fertilization rate than four-well dish culture, probably due to a homogenous sperm distribution. Despite the differences in time outside the incubator and laboratory expenses (which are after all insignificant microdroplet culture allows a better control over the embryo development. The embryos of best developmental potential can therefore be chosen for ET.

  9. Effects of irradiation distance on supply of reactive oxygen species to the bottom of a Petri dish filled with liquid by an atmospheric O{sub 2}/He plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Kawasaki, Toshiyuki, E-mail: kawasaki@nbu.ac.jp; Kusumegi, Shota; Kudo, Akihiro; Sakanoshita, Tomohiro; Tsurumaru, Takuya; Sato, Akihiro [Department of Mechanical and Electrical Engineering, Nippon Bunri University, Oita, Oita 870-0397 (Japan); Uchida, Giichiro [Joining and Welding Research Institute, Osaka University, Ibaraki, Osaka 567-0047 (Japan); Koga, Kazunori; Shiratani, Masaharu [Graduate School of Information Science and Electrical Engineering, Kyushu University, Fukuoka, Fukuoka 819-0395 (Japan)

    2016-05-07

    The impact of irradiation distances on plasma jet-induced specific effects on the supply of reactive oxygen species (ROS) to the bottom of a Petri dish filled with liquid was investigated using a KI-starch gel reagent that can be employed as a ROS indicator even in water. O{sub 3} exposure experiments without plasma irradiation were also performed to elucidate the specific effects of the plasma jet. Relative concentrations of ROS transported to the bottom were evaluated using absorbance measurements. The results indicated that ROS supply to the bottom is markedly enhanced by the plasma jet irradiation at shorter irradiation distances, whereas similar results could not be obtained for the O{sub 3} exposure. In these cases, the liquid mixing in the depth direction was also enhanced by the plasma jet irradiation only, and the supply of reactive atomic oxygen to the liquid surface was markedly increased as well.

  10. Functional Programming

    OpenAIRE

    Chitil, Olaf

    2009-01-01

    Functional programming is a programming paradigm like object-oriented programming and logic programming. Functional programming comprises both a specific programming style and a class of programming languages that encourage and support this programming style. Functional programming enables the programmer to describe an algorithm on a high-level, in terms of the problem domain, without having to deal with machine-related details. A program is constructed from functions that only map inputs to ...

  11. Dish/stirling hybrid-receiver

    Science.gov (United States)

    Mehos, Mark S.; Anselmo, Kenneth M.; Moreno, James B.; Andraka, Charles E.; Rawlinson, K. Scott; Corey, John; Bohn, Mark S.

    2002-01-01

    A hybrid high-temperature solar receiver is provided which comprises a solar heat-pipe-receiver including a front dome having a solar absorber surface for receiving concentrated solar energy, a heat pipe wick, a rear dome, a sidewall joining the front and the rear dome, and a vapor and a return liquid tube connecting to an engine, and a fossil fuel fired combustion system in radial integration with the sidewall for simultaneous operation with the solar heat pipe receiver, the combustion system comprising an air and fuel pre-mixer, an outer cooling jacket for tangentially introducing and cooling the mixture, a recuperator for preheating the mixture, a burner plenum having an inner and an outer wall, a porous cylindrical metal matrix burner firing radially inward facing a sodium vapor sink, the mixture ignited downstream of the matrix forming combustion products, an exhaust plenum, a fossil-fuel heat-input surface having an outer surface covered with a pin-fin array, the combustion products flowing through the array to give up additional heat to the receiver, and an inner surface covered with an extension of the heat-pipe wick, a pin-fin shroud sealed to the burner and exhaust plenums, an end seal, a flue-gas diversion tube and a flue-gas valve for use at off-design conditions to limit the temperature of the pre-heated air and fuel mixture, preventing pre-ignition.

  12. Design rules against buckling of dished heads

    International Nuclear Information System (INIS)

    Roche, R.L.; Alix, M.; Autrusson, B.

    1984-01-01

    The aim of this paper is to present the validation of the rules of the French code of presure vessels CODAP. First, it is shown that the theories of buckling cannot give alone a sufficient base of validation and that the experimental justification is necessary. Then, the admissible pressure values corresponding to the CODAP formules are compared with the experimental results. This comparison furnishes the safety margins given by the CODAP formules. Finally, buckling tests of torispherical shells carried out at the CEA Saclay (France) are presented. The results obtained can be represented by a simple semi-empiric formula [fr

  13. Dishing the dirt: Gossiping in organizations

    NARCIS (Netherlands)

    Clegg, S.R.; van Iterson, A

    2009-01-01

    In an exercise in social theory, rather than an empirical investigation, we concentrate on the role of gossip - spreading 'news about the affairs of another' - in relation to the dynamics of power in organizations. Gossip has often been seen in functional terms, as both positive and negative for the

  14. The dish on the Solar Decathlon

    Energy Technology Data Exchange (ETDEWEB)

    Meehan, Chris

    2011-07-01

    Within only one week, 19 collegiate teams had to build their technically-advanced, solar-powered, energy-efficient houses to wow judges and the public at this year's US Department of Energy's (DOE's) Solar Decathlon. The unassembled homes began arriving at the West Potomac Park of the National Mall in Washington, DC, at 11 p.m. on September 13. From then on it was a marathon to finish construction and compete in gauntlet of 10 events to test the designs. (orig.)

  15. Strontium-90 and cesium-137 in milk (producing districts for domestic program) (from Jun. 1984 to Oct. 1984)

    International Nuclear Information System (INIS)

    1984-01-01

    Sr-90 and Cs-137 in milk from producing districts for domestic program were determined using radiochemical analysis. Raw milk was collected from six sampling locations. Milk in a stainless steel pan or a porcelain dish was evaporated to dryness followed by carbonization and ashing. The maximum values of Sr-90 and Cs-137 were 2.3 +- 0.26 pCi/l in milk from Ishikawa and 2.5 +- 0.22 pCi/l in milk from Ehime, respectively, collected in August 1984. (Namekawa, K.)

  16. Strontium-90 and cesium-137 in milk (producing districts for WHO program) from Nov. 1983 to Jan. 1984

    International Nuclear Information System (INIS)

    1984-01-01

    Sr-90 and Cs-137 in milk from producing districts for WHO program were determined using radiochemical analysis. Raw milk was collected from 11 sampling locations. Milk in a stainless steel pan or a porcelain dish was evaporated to dryness followed by carbonization and ashing. The maximum values of Sr-90 and Cs-137 were 11.0+-0.50 pCi/l and 50.0+-0.90 pCi/l, respectively, in milk from Tokyo in February 1984. (Namekawa, K.)

  17. Strontium-90 and cesium-137 in milk (producing districts for domestic program) from Jun. 1983 to Sept. 1983

    International Nuclear Information System (INIS)

    1984-01-01

    Sr-90 and Cs-137 in milk from producing districts for domestic program were determined using radiochemical analysis. Raw milk was collected from six sampling locations. Milk in a stainless steel pan or a porcelain dish was evaporated to dryness followed by carbonization and ashing. The maximum values of Sr-90 and Cs-137 were 2.8+-0.30 pCi/l and 1.8+-0.23 pCi/l, respectively, in milk collected from Aomori in February 1984. (Namekawa, K.)

  18. Program specialization

    CERN Document Server

    Marlet, Renaud

    2013-01-01

    This book presents the principles and techniques of program specialization - a general method to make programs faster (and possibly smaller) when some inputs can be known in advance. As an illustration, it describes the architecture of Tempo, an offline program specializer for C that can also specialize code at runtime, and provides figures for concrete applications in various domains. Technical details address issues related to program analysis precision, value reification, incomplete program specialization, strategies to exploit specialized program, incremental specialization, and data speci

  19. Program History

    Science.gov (United States)

    Learn how the National Cancer Institute transitioned the former Cooperative Groups Program to the National Clinical Trials Network (NCTN) program. The NCTN gives funds and other support to cancer research organizations to conduct cancer clinical trials.

  20. Program auto

    International Nuclear Information System (INIS)

    Rawool-Sullivan, M.W.; Plagnol, E.

    1990-01-01

    The program AUTO was developed to be used in the analysis of dE vs E type spectra. This program is written in FORTRAN and calculates dE vs E lines in MeV. The provision is also made in the program to convert these lines from MeV to ADC channel numbers to facilitate the comparison with the raw data from the experiments. Currently the output of this program can be plotted with the display program, called VISU, but it can also be used independent of the program VISU, with little or no modification in the actual fortran code. The program AUTO has many useful applications. In this article the program AUTO is described along with its applications

  1. Material Programming

    DEFF Research Database (Denmark)

    Vallgårda, Anna; Boer, Laurens; Tsaknaki, Vasiliki

    2017-01-01

    . Consequently we ask what the practice of programming and giving form to such materials would be like? How would we be able to familiarize ourselves with the dynamics of these materials and their different combinations of cause and effect? Which tools would we need and what would they look like? Will we program......, and color, but additionally being capable of sensing, actuating, and computing. Indeed, computers will not be things in and by themselves, but embedded into the materials that make up our surroundings. This also means that the way we interact with computers and the way we program them, will change...... these computational composites through external computers and then transfer the code them, or will the programming happen closer to the materials? In this feature we outline a new research program that floats between imagined futures and the development of a material programming practice....

  2. Effective Programming

    DEFF Research Database (Denmark)

    Frost, Jacob

    To investigate the use of VTLoE as a basis for formal derivation of functional programs with effects. As a part of the process, a number of issues central to effective formal programming are considered. In particular it is considered how to develop a proof system suitable for pratical reasoning......, how to implement this system in the generic proof assistant Isabelle and finally how to apply the logic and the implementation to programming....

  3. Program Fullerene

    DEFF Research Database (Denmark)

    Wirz, Lukas; Peter, Schwerdtfeger,; Avery, James Emil

    2013-01-01

    Fullerene (Version 4.4), is a general purpose open-source program that can generate any fullerene isomer, perform topological and graph theoretical analysis, as well as calculate a number of physical and chemical properties. The program creates symmetric planar drawings of the fullerene graph, an......-Fowler, and Brinkmann-Fowler vertex insertions. The program is written in standard Fortran and C++, and can easily be installed on a Linux or UNIX environment....

  4. Programming F#

    CERN Document Server

    Smith, Chris

    2009-01-01

    Why learn F#? This multi-paradigm language not only offers you an enormous productivity boost through functional programming, it also lets you develop applications using your existing object-oriented and imperative programming skills. With Programming F#, you'll quickly discover the many advantages of Microsoft's new language, which includes access to all the great tools and libraries of the .NET platform. Learn how to reap the benefits of functional programming for your next project -- whether it's quantitative computing, large-scale data exploration, or even a pursuit of your own. With th

  5. PLC Programming

    International Nuclear Information System (INIS)

    Lee, Seong Jae; Wi, Seong Dong; Yoo, Jong Seon; Kim, Se Chan

    2001-02-01

    This book tells of PLC programming for KGL-WIN with summary of PLC, performance and function of PLC like characteristic of KGL-WIN, connection method with PLC, basic performance of K200S/K300S/K1000S, diagram of input and output H/W, writing project, staring the program, editing of program, on-line function, debugging and instructions like control, timer and counter, data transmission, comparison, rotation and moving, system, data operating data conversion and application program.

  6. Programming Interactivity

    CERN Document Server

    Noble, Joshua

    2009-01-01

    Make cool stuff. If you're a designer or artist without a lot of programming experience, this book will teach you to work with 2D and 3D graphics, sound, physical interaction, and electronic circuitry to create all sorts of interesting and compelling experiences -- online and off. Programming Interactivity explains programming and electrical engineering basics, and introduces three freely available tools created specifically for artists and designers: Processing, a Java-based programming language and environment for building projects on the desktop, Web, or mobile phonesArduino, a system t

  7. Computer Programs.

    Science.gov (United States)

    Anderson, Tiffoni

    This module provides information on development and use of a Material Safety Data Sheet (MSDS) software program that seeks to link literacy skills education, safety training, and human-centered design. Section 1 discusses the development of the software program that helps workers understand the MSDSs that accompany the chemicals with which they…

  8. BASIC Programming.

    Science.gov (United States)

    Jennings, Carol Ann

    Designed for use by both secondary- and postsecondary-level business teachers, this curriculum guide consists of 10 units of instructional materials dealing with Beginners All-Purpose Symbol Instruction Code (BASIC) programing. Topics of the individual lessons are numbering BASIC programs and using the PRINT, END, and REM statements; system…

  9. Choreographic Programming

    DEFF Research Database (Denmark)

    Montesi, Fabrizio

    , as they offer a concise view of the message flows enacted by a system. For this reason, in the last decade choreographies have been used in the development of programming languages, giving rise to a programming paradigm that in this dissertation we refer to as Choreographic Programming. Recent studies show...... endpoint described in a choreography can then be automatically generated, ensuring that such implementations are safe by construction. However, current formal models for choreographies do not deal with critical aspects of distributed programming, such as asynchrony, mobility, modularity, and multiparty...... sessions; it remains thus unclear whether choreographies can still guarantee safety when dealing with such nontrivial features. This PhD dissertation argues for the suitability of choreographic programming as a paradigm for the development of safe distributed systems. We proceed by investigating its...

  10. Icobj Programming

    OpenAIRE

    Boussinot , Frédéric

    1996-01-01

    A simple and fully graphical programming method is presented, using a powerful means to combine behaviors. This programming is based on the notion of an «icobj» which has a behavioral aspect («object» part), a graphical aspect («icon» part), with an «animation» aspect. Icobj programming provides parallelism, broadcast event communication and migration through the network. An experimental system based on this approach is described in details. Its implementation with reactive scripts is also pr...

  11. Programming Python

    CERN Document Server

    Lutz, Mark

    2011-01-01

    If you've mastered Python's fundamentals, you're ready to start using it to get real work done. Programming Python will show you how, with in-depth tutorials on the language's primary application domains: system administration, GUIs, and the Web. You'll also explore how Python is used in databases, networking, front-end scripting layers, text processing, and more. This book focuses on commonly used tools and libraries to give you a comprehensive understanding of Python's many roles in practical, real-world programming. You'll learn language syntax and programming techniques in a clear and co

  12. Program overview

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    The program overview describes the following resources and facilities; laser facilities, main laser room, target room, energy storage, laboratory area, building support systems, general plant project, and the new trailer complex

  13. Linear programming

    CERN Document Server

    Solow, Daniel

    2014-01-01

    This text covers the basic theory and computation for a first course in linear programming, including substantial material on mathematical proof techniques and sophisticated computation methods. Includes Appendix on using Excel. 1984 edition.

  14. Science Programs

    Science.gov (United States)

    Laboratory Delivering science and technology to protect our nation and promote world stability Science & ; Innovation Collaboration Careers Community Environment Science & Innovation Facilities Science Pillars Research Library Science Briefs Science News Science Highlights Lab Organizations Science Programs Applied

  15. SPOT Program

    Science.gov (United States)

    Smith, Jason T.; Welsh, Sam J.; Farinetti, Antonio L.; Wegner, Tim; Blakeslee, James; Deboeck, Toni F.; Dyer, Daniel; Corley, Bryan M.; Ollivierre, Jarmaine; Kramer, Leonard; hide

    2010-01-01

    A Spacecraft Position Optimal Tracking (SPOT) program was developed to process Global Positioning System (GPS) data, sent via telemetry from a spacecraft, to generate accurate navigation estimates of the vehicle position and velocity (state vector) using a Kalman filter. This program uses the GPS onboard receiver measurements to sequentially calculate the vehicle state vectors and provide this information to ground flight controllers. It is the first real-time ground-based shuttle navigation application using onboard sensors. The program is compact, portable, self-contained, and can run on a variety of UNIX or Linux computers. The program has a modular objec-toriented design that supports application-specific plugins such as data corruption remediation pre-processing and remote graphics display. The Kalman filter is extensible to additional sensor types or force models. The Kalman filter design is also strong against data dropouts because it uses physical models from state and covariance propagation in the absence of data. The design of this program separates the functionalities of SPOT into six different executable processes. This allows for the individual processes to be connected in an a la carte manner, making the feature set and executable complexity of SPOT adaptable to the needs of the user. Also, these processes need not be executed on the same workstation. This allows for communications between SPOT processes executing on the same Local Area Network (LAN). Thus, SPOT can be executed in a distributed sense with the capability for a team of flight controllers to efficiently share the same trajectory information currently being computed by the program. SPOT is used in the Mission Control Center (MCC) for Space Shuttle Program (SSP) and International Space Station Program (ISSP) operations, and can also be used as a post -flight analysis tool. It is primarily used for situational awareness, and for contingency situations.

  16. Sprego programming

    OpenAIRE

    Csernoch, Mária; Biró, Piroska

    2015-01-01

    Spreadsheet management is a border-land between office applications and programming, however, it is rather communicated that spreadsheet is nothing more than an easily handled fun piece. Consequently, the complexity of spreadsheet handling, the unprepared end-users, their problem solving abilities and approaches do not match. To overcome these problems we have developed and introduced Sprego (Spreadsheet Lego). Sprego is a simplified functional programming language in spreadsheet environment,...

  17. Recombinant Programming

    OpenAIRE

    Pawlak , Renaud; Cuesta , Carlos; Younessi , Houman

    2004-01-01

    This research report presents a promising new approach to computation called Recombinant Programming. The novelty of our approach is that it separates the program into two layers of computation: the recombination and the interpretation layer. The recombination layer takes sequences as inputs and allows the programmer to recombine these sequences through the definition of cohesive code units called extensions. The output of such recombination is a mesh that can be used by the interpretation la...

  18. Integer programming

    CERN Document Server

    Conforti, Michele; Zambelli, Giacomo

    2014-01-01

    This book is an elegant and rigorous presentation of integer programming, exposing the subject’s mathematical depth and broad applicability. Special attention is given to the theory behind the algorithms used in state-of-the-art solvers. An abundance of concrete examples and exercises of both theoretical and real-world interest explore the wide range of applications and ramifications of the theory. Each chapter is accompanied by an expertly informed guide to the literature and special topics, rounding out the reader’s understanding and serving as a gateway to deeper study. Key topics include: formulations polyhedral theory cutting planes decomposition enumeration semidefinite relaxations Written by renowned experts in integer programming and combinatorial optimization, Integer Programming is destined to become an essential text in the field.

  19. Programming Algol

    CERN Document Server

    Malcolme-Lawes, D J

    2014-01-01

    Programming - ALGOL describes the basics of computer programming using Algol. Commands that could be added to Algol and could increase its scope are described, including multiplication and division and the use of brackets. The idea of labeling or naming a command is also explained, along with a command allowing two alternative results. Most of the important features of Algol syntax are discussed, and examples of compound statements (that is, sets of commands enclosed by a begin ... end command) are given.Comprised of 11 chapters, this book begins with an introduction to the digital computer an

  20. Programming Interactivity

    CERN Document Server

    Noble, Joshua

    2012-01-01

    Ready to create rich interactive experiences with your artwork, designs, or prototypes? This is the ideal place to start. With this hands-on guide, you'll explore several themes in interactive art and design-including 3D graphics, sound, physical interaction, computer vision, and geolocation-and learn the basic programming and electronics concepts you need to implement them. No previous experience is necessary. You'll get a complete introduction to three free tools created specifically for artists and designers: the Processing programming language, the Arduino microcontroller, and the openFr

  1. SLED program

    International Nuclear Information System (INIS)

    Farkas, Z.D.

    1977-04-01

    A FORTRAN program is described which, for a given cavity and timing, yields all fields as a (piecewise) function of time, and which, for any mix of SLEDded and non-SLEDded klystrons of any given energy/klystron, yields the SLED operation parameters. The note explains the input and output parameters as they appear in the code output. 3 figures, 19 tables

  2. ORGEL program

    Energy Technology Data Exchange (ETDEWEB)

    none

    1963-09-01

    Parameter optimization studies for an ORGEL power plant are reported, and the ESSOR test reactor used in the program is described. Research at Ispra in reactor physics, technology, metallurgy, heat transfer, chemistry, and physical chemistry associated with ORGEL development is also summarized. (D.C.W.)

  3. Program evaluation

    Energy Technology Data Exchange (ETDEWEB)

    1988-01-01

    This book contains the proceedings from the panel on program evaluation. Some of the papers included are the following: Seattle City Light's Industrial Retrofit Demonstration Project Uses Quasi-Experimental Research Design and Metering to Measure Savings, Evaluation for PUCs, and The Takeback Effect Low-income Weatherizations Fact or Fiction

  4. Sprego Programming

    Directory of Open Access Journals (Sweden)

    Maria Csernoch

    2015-02-01

    Full Text Available Spreadsheet management is a border-land between office applications and programming, however, it is rather communicated that spreadsheet is nothing more than an easily handled fun piece. Consequently, the complexity of spreadsheet handling, the unprepared end-users, their problem solving abilities and approaches do not match. To overcome these problems we have developed and introduced Sprego (Spreadsheet Lego. Sprego is a simplified functional programming language in spreadsheet environment, and such as can be used both as introductory language and the language of end-user programmers. The essence of Sprego is that we use as few and simple functions as possible and based on these functions build multilevel formulas. With this approach, similar to high level programming, we are able solve advanced problems, developing algorithmic skills, computational thinking. The advantage of Sprego is the simplicity of the language, when the emphasis is not on the coding but on the problem. Beyond that spreadsheets would provide real life problems with authentic data and tables which students are more interested in than the artificial environment and semi-authentic problems of high level programming languages.

  5. Polytypic Programming

    NARCIS (Netherlands)

    Jeuring, J.T.; Jansson, P.

    1996-01-01

    Many functions have to be written over and over again for different datatypes, either because datatypes change during the development of programs, or because functions with similar functionality are needed on different datatypes. Examples of such functions are pretty printers, debuggers, equality

  6. Refurbishment programs

    International Nuclear Information System (INIS)

    Irish, C.S.

    2004-01-01

    As nuclear plants age, equipment becomes obsolete, outdated or just simply unreliable. This puts a lot of emphasis on replacement of the subject equipment. This can be an expensive proposition for safety related equipment due to design changes, requalification charges and the cost of the new equipment, specifically when the original component is obsolete. The presentation will explain how comprehensive refurbishment programs on many different types of equipment can alleviate this situation. The refurbishment program is a systematic refurbishment of equipment to an as new condition by replacing all of the age sensitive components within the equipment. This is carried out on all of the same type of equipment in a scheduled program. For example the plant may to decide to refurbish all of their Lambda LME-24 power supplies, or all of their Bailey modules, or all of their Agastat DSC Series relays. Independent of the item the process is the same. Refurbish each piece of equipment to an as new condition by replacing all of the age sensitive equipment. The equipment is then returned to the client as safety related, existing qualification maintained and with a new service life/warranty. This is not a simple repair. It is a planned refurbishment to an as new condition of certain equipment types throughout the plant and then carried out from equipment piece to equipment piece. The refurbishment program may even include introducing new spares into the plant. This is normally performed by upgrading (dedicating for safety related use and refurbishing to an 'as new' condition) surplus equipment and using these equipment pieces in the rotation of the plant equipment to refurbish the entire population of a selected piece of equipment at the plant. This process can be performed on many equipment types including power supplies, circuit boards, modules, relays, motors, breakers, and many more. The refurbishment program greatly increases the reliability of the equipment without the

  7. Constraint Programming versus Mathematical Programming

    DEFF Research Database (Denmark)

    Hansen, Jesper

    2003-01-01

    Constraint Logic Programming (CLP) is a relatively new technique from the 80's with origins in Computer Science and Artificial Intelligence. Lately, much research have been focused on ways of using CLP within the paradigm of Operations Research (OR) and vice versa. The purpose of this paper...

  8. A Program to Teach Programming.

    Science.gov (United States)

    Fenichel, Robert R.; And Others

    1969-01-01

    The TEACH system was developed to provide inexpensive, effective, virtually instructorless instruction in programing. The TEACH system employed an interactive language, UNCL. Two full sections of the TEACH course were taught. The results of this experience suggested ways in which the research and development effort on the system should be…

  9. Program overview: Subsurface science program

    International Nuclear Information System (INIS)

    1994-03-01

    The OHER Subsurface Science Program is DOE's core basic research program concerned with subsoils and groundwater. These practices have resulted in contamination by mixtures of organic chemicals, inorganic chemicals, and radionuclides. A primary long-term goal is to provide a foundation of knowledge that will lead to the reduction of environmental risks and to cost-effective cleanup strategies. Since the Program was initiated in 1985, a substantial amount of research in hydrogeology, subsurface microbiology, and the geochemistry of organically complexed radionuclides has been completed, leading to a better understanding of contaminant transport in groundwater and to new insights into microbial distribution and function in the subsurface environments. The Subsurface Science Program focuses on achieving long-term scientific advances that will assist DOE in the following key areas: providing the scientific basis for innovative in situ remediation technologies that are based on a concept of decontamination through benign manipulation of natural systems; understanding the complex mechanisms and process interactions that occur in the subsurface; determining the influence of chemical and geochemical-microbial processes on co-contaminant mobility to reduce environmental risks; improving predictions of contaminant transport that draw on fundamental knowledge of contaminant behavior in the presence of physical and chemical heterogeneities to improve cleanup effectiveness and to predict environmental risks

  10. Linear programming

    CERN Document Server

    Karloff, Howard

    1991-01-01

    To this reviewer’s knowledge, this is the first book accessible to the upper division undergraduate or beginning graduate student that surveys linear programming from the Simplex Method…via the Ellipsoid algorithm to Karmarkar’s algorithm. Moreover, its point of view is algorithmic and thus it provides both a history and a case history of work in complexity theory. The presentation is admirable; Karloff's style is informal (even humorous at times) without sacrificing anything necessary for understanding. Diagrams (including horizontal brackets that group terms) aid in providing clarity. The end-of-chapter notes are helpful...Recommended highly for acquisition, since it is not only a textbook, but can also be used for independent reading and study. —Choice Reviews The reader will be well served by reading the monograph from cover to cover. The author succeeds in providing a concise, readable, understandable introduction to modern linear programming. —Mathematics of Computing This is a textbook intend...

  11. Program summary

    International Nuclear Information System (INIS)

    1982-07-01

    The operating, construction, and development activities of the Department of Energy in the areas of uranium enrichment are described. The DOE supplies the enrichment service through toll enrichment contracts with foreign and domestic utilities by enriching uranium supplied by the utility to the desired U-235 level. This role will continue well into the next century. In addition it provides enriched uranium for US Government needs and for R and D purposes. At the present time, almost all the world's capacity to produce enriched uranium uses the gaseous diffusion process. The United States built the first gaseous diffusion plant during World War II. Later this plant was expanded and two additional plants were built. There is presently a $1.5 billion improvement and uprating program near completion which will improve the plant efficiency and increase the total capacity of the three plants by 60 percent to 27.3 million SWU per year. The Administration's energy message in 1977 provided for a further expansion of this capacity by using gas centrifuge technology. The new gas centrifuge plant is being built near the existing GDP near Portsmouth, Ohio. The normal capacity of an 8 building process plant will be 13.2 million SWU per year. The first 2.2 million SWU of capacity is scheduled to be available in 1989. The remaining capacity will be added as needed to meet demand and the overall goal of the program. The goal of the Uranium Enrichment Program is to meet domestic, foreign, and US Government requirements for uranium enrichment services in an economical, reliable, safe and environmentally acceptable manner. To ensure accomplishment of this goal, the overall program is broken down into three areas of implementation; Enrichment Operations; Capacity Upgrading Operations; and Business Operations

  12. Robot Programming.

    Science.gov (United States)

    1982-12-01

    Paris, France, June, 1982, 519-530. Latoinbe, J. C. "Equipe Intelligence Artificielle et Robotique: Etat d’avancement des recherches," Laboratoire...8217AD-A127 233 ROBOT PROGRRMMING(U) MASSACHUSETTS INST OFGTECHi/ CAMBRIDGE ARTIFICIAL INTELLIGENCE LAB T LOZANO-PEREZ UNCLASSIFIED DC8 AI-9 N884...NAME AND ADDRESS 10. PROGRAM ELEMENT. PROJECT. TASK Artificial Intelligence Laboratory AREA I WORK UNIT NUMBERS ,. 545 Technology Square Cambridge

  13. Micro Programming

    OpenAIRE

    Spanjersberg , Herman

    2012-01-01

    International audience; In the 1970s a need arose to perform special arithmetic operations on minicomputers much more quickly than had been possible in the past. This paper tells the story of why micro programming was needed for special arithmetic operations on mini computers in the 1970s and how it was implemented. The paper tells how the laboratory in which the first experiment took place had a PDP-9 minicomputer from Digital Equipment Corporation and how the author, with several colleagues...

  14. Choreographic Programming

    OpenAIRE

    Montesi, Fabrizio

    2014-01-01

    Choreographies are descriptions of distributed systems where the developer gives a global view of how messages are exchanged by endpoint nodes (endpoints for short), instead of separately defining the behaviour of each endpoint. They have a significant impact on the quality of software, as they offer a concise view of the message flows enacted by a system. For this reason, in the last decade choreographies have been used in the development of programming languages, giving rise to a programmin...

  15. SUCO program

    International Nuclear Information System (INIS)

    Knebel, J.U.

    1995-01-01

    The SUCO program is a three-step series of scaled model experiments investigating the optional sump cooling concept of the EPR. This concept is entirely based on passive safety features. This report presents the basic physical phenomena and scaling criteria of decay heat removal from a large coolant pool by single-phase and two-phase natural circulation flow. The physical significance of the dimensionless similarity groups derived is evaluated. The report gives first measurement results of the 1:20 linearly scaled plane two-dimensional SUCOS-2D test facility. The real height SUCOT test facility that is in its building up phase is presented. (orig.)

  16. Programming Pig

    CERN Document Server

    Gates, Alan

    2011-01-01

    This guide is an ideal learning tool and reference for Apache Pig, the open source engine for executing parallel data flows on Hadoop. With Pig, you can batch-process data without having to create a full-fledged application-making it easy for you to experiment with new datasets. Programming Pig introduces new users to Pig, and provides experienced users with comprehensive coverage on key features such as the Pig Latin scripting language, the Grunt shell, and User Defined Functions (UDFs) for extending Pig. If you need to analyze terabytes of data, this book shows you how to do it efficiently

  17. Geothermal Technologies Program Overview - Peer Review Program

    Energy Technology Data Exchange (ETDEWEB)

    Milliken, JoAnn [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2011-06-06

    This Geothermal Technologies Program presentation was delivered on June 6, 2011 at a Program Peer Review meeting. It contains annual budget, Recovery Act, funding opportunities, upcoming program activities, and more.

  18. TNS Program

    International Nuclear Information System (INIS)

    Anon.

    1979-01-01

    The fusion program plan is briefly reviewed and the role of the prototype experimental power reactor, thought of as The Next Step (TNS), is discussed. The required device capabilities and basic reactor concepts for a TNS fusion electric plant are given. A detailed discussion of the physics considerations for the Power Generating Fusion Reactor (PGFR), including plasma heating, MHD equilibrium and stability, burn control resulting from toroidal field ripple, fueling, and boundary effects, is presented. Engineering considerations of the major PGFR systems, as well as diagnostics, instrumentation, control, and programmatic issues are also considered in detail. It is concluded that TNS design studies have established the existence of a technical basis for constructing a long pulse, D-T burning tokamak to be operational prior to 1990

  19. Telemedicine Program

    Science.gov (United States)

    1996-01-01

    Since the 1970s, NASA has been involved in the research and demonstration of telemedicine for its potential in the care of astronauts in flight and Earth-bound applications. A combination of NASA funding, expertise and off-the-shelf computer and networking systems made telemedicine possible for a medically underserved hospital in Texas. Through two-way audio/video relay, the program links pediatric oncology specialists at the University of Texas Health Science Center in San Antonio to South Texas Hospital in Harlingen, providing easier access and better care to children with cancer. Additionally, the hospital is receiving teleclinics on pediatric oncology nursing, family counseling and tuberculosis treatment. VTEL Corporation, Sprint, and the Healthcare Open Systems and Trials Consortium also contributed staff and hardware.

  20. Russian programs

    International Nuclear Information System (INIS)

    Heywood, A.

    1993-01-01

    Lawrence Livermore National Laboratory (LLNL) initiated several projects with the Boreskov Institute of Catalysis to develop innovative process technologies for the treatment of mixed and hazardous wastes containing a high percentage of organic material. Each of these processes involves the use of catalysts for oxidation (or initial reduction) of the hazardous organic constituents. Because of their commitment to a national mixed waste treatment program, both the Department of Energy/Office of Environmental Management (DOE/EM) and LLNL Environmental Restoration and Waste Management/Applied Technologies (ER-WM/AT) programs have a considerable interest in innovative/alternative flowsheets for organic mixed waste treatment. Selective Catalytic Reduction (SCR) using ammonia as a reducing agent is current a preferred method of treating NO x in off-gases. The advantages of SCR over methods, such as wet scrubbing, include compact design, low maintenance, and the absence of gas cooling requirements and secondary wastes. Any further improvements in catalyst design would lower costs, improve their resistance to poisons, expand their ability to promote oxidation/reduction in mixtures such as NO x /CO, and increase their mechanical strength. An additional requirement of catalysts to be used in California is that the catalyst formulations must meet the California Land Ban disposal restrictions. A monitoring network is needed in Russia to coordinate the environmental monitoring activities of government (including military establishments and facilities) and commercial entities. The network shall incorporate existing as well as proposed monitoring stations. It will comply with all toxic substance control regulations and include analyses for all priority radiochemical and chemical substances. A database compatible with the Environmental Technologies for Remedial Actions Data Exchange (EnviroTRADE) database will ultimately be compiled

  1. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Trauma Programs Trauma Programs About Trauma Programs Violence Prevention BleedingControl.org Trauma Quality Programs National Trauma Data ... Conference Publications and Posters National Trauma System Injury Prevention and Control Quality and Safety Conference Quality and ...

  2. Human Reliability Program Overview

    Energy Technology Data Exchange (ETDEWEB)

    Bodin, Michael

    2012-09-25

    This presentation covers the high points of the Human Reliability Program, including certification/decertification, critical positions, due process, organizational structure, program components, personnel security, an overview of the US DOE reliability program, retirees and academia, and security program integration.

  3. Vehicle Technologies Program Overview

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2006-09-05

    Overview of the Vehicle Technologies Program including external assessment and market view; internal assessment, program history and progress; program justification and federal role; program vision, mission, approach, strategic goals, outputs, and outcomes; and performance goals.

  4. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Trauma Trauma Programs Trauma Programs About Trauma Programs Violence Prevention BleedingControl.org Trauma Quality Programs National Trauma ... Benefits Current Openings Newsroom Newsroom Newsroom Press Releases Media Resources The FIRST Trial ACS Publications ACS in ...

  5. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... and Safety Conference Participant Use Data File Surgical Risk Calculator Frequently Asked Questions Participant Hub Contact Us ... Trauma Programs Trauma Programs About Trauma Programs Violence Prevention BleedingControl.org Trauma Quality Programs National Trauma Data ...

  6. Practical C++ programming

    National Research Council Canada - National Science Library

    Oualline, Steve

    2003-01-01

    ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4 6 3 2. The Basics of Program Writing Programs from Conception to Execution Creating a Real Program Getting Help in Unix Getting Help in an IDE Programming...

  7. Functional Python programming

    CERN Document Server

    Lott, Steven

    2015-01-01

    This book is for developers who want to use Python to write programs that lean heavily on functional programming design patterns. You should be comfortable with Python programming, but no knowledge of functional programming paradigms is needed.

  8. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Membership Directory 2017 Annual Meeting 2016 Annual Meeting Women's Committee Mentorship Program Outside Activities ACS Archives Contact Us Quality Programs Quality Programs Overview About Quality Programs ACS ...

  9. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Continuous Certification Requirements SSR Login MIPS Resources and Education Quality and Safety Conference Trauma Trauma Programs Trauma Programs About Trauma Programs Violence Prevention BleedingControl.org Trauma Quality Programs National Trauma ...

  10. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Membership Directory 2017 Annual Meeting 2016 Annual Meeting Women's Committee Mentorship Program Outside Activities ACS Archives Contact Us Quality Programs Quality Programs Overview About Quality Programs ACS Leadership in Quality ACS Leadership in Quality Setting the ...

  11. From raw material to dish: pasta quality step by step.

    Science.gov (United States)

    Sicignano, Angelo; Di Monaco, Rossella; Masi, Paolo; Cavella, Silvana

    2015-10-01

    Pasta is a traditional Italian cereal-based food that is popular worldwide because of its convenience, versatility, sensory and nutritional value. The aim of this review is to present a step-by-step guide to facilitate the understanding of the most important events that can affect pasta characteristics, directing the reader to the appropriate production steps. Owing to its unique flavor, color, composition and rheological properties, durum wheat semolina is the best raw material for pasta production. Although pasta is traditionally made from only two ingredients, sensory quality and chemical/physical characteristics of the final product may vary greatly. Starting from the same ingredients, there are a lot of different events in each step of pasta production that can result in the development of varieties of pasta with different characteristics. In particular, numerous studies have demonstrated the importance of temperature and humidity conditions of the pasta drying operation as well as the significance of the choice of raw material and operating conditions on pasta quality. © 2015 Society of Chemical Industry.

  12. Dish concentrators for solar thermal energy: Status and technology development

    Science.gov (United States)

    Jaffe, L. D.

    1982-01-01

    Point-focusing concentrators under consideration for solar thermal energy use are reviewed. These concentrators differ in such characteristics as optical configuration, optical materials, structure for support of the optical elements and of the receiver, mount, foundation, drive, controls and enclosure. Concentrator performance and cost are considered. Technology development is outlined, including wind loads and aerodynamics; precipitation, sand, and seismic considerations; and maintenance and cleaning.

  13. A Compendium of Solar Dish/Stirling Technology

    Science.gov (United States)

    1994-01-01

    systems and Plataforma Solar in Almeria, Spain, with the goal being plans to produce fourteen 7.5-kWe systems for testing to test the system’s long-term...the sun is not a point source, its rays 21 Chapter 3 (a) (b) - N Mounting Ring and CollaraI/ / I/\\ I / Virtual Exit I / Target S• Entrance I 0 L...tptical \\ I Real Exit / Virtual Target \\ Aperture\\ / Cooling \\ / I Coils N - Focal - - - - " Plane 4. Figure 3-2. A secondary concentrator with side view (a

  14. Behavioral program synthesis with genetic programming

    CERN Document Server

    Krawiec, Krzysztof

    2016-01-01

    Genetic programming (GP) is a popular heuristic methodology of program synthesis with origins in evolutionary computation. In this generate-and-test approach, candidate programs are iteratively produced and evaluated. The latter involves running programs on tests, where they exhibit complex behaviors reflected in changes of variables, registers, or memory. That behavior not only ultimately determines program output, but may also reveal its `hidden qualities' and important characteristics of the considered synthesis problem. However, the conventional GP is oblivious to most of that information and usually cares only about the number of tests passed by a program. This `evaluation bottleneck' leaves search algorithm underinformed about the actual and potential qualities of candidate programs. This book proposes behavioral program synthesis, a conceptual framework that opens GP to detailed information on program behavior in order to make program synthesis more efficient. Several existing and novel mechanisms subs...

  15. Final Report on the Operation and Maintenance Improvement Program for Concentrating Solar Power Plants

    International Nuclear Information System (INIS)

    Cohen, Gilbert E.; Kearney, David W.; Kolb, Gregory J.

    1999-01-01

    This report describes the results of a six-year, $6.3 million project to reduce operation and maintenance (O ampersand M) costs at power plants employing concentrating solar power (CSP) technology. Sandia National Laboratories teamed with KJC Operating Company to implement the O ampersand M Improvement Program. O ampersand M technologies developed during the course of the program were demonstrated at the 150-MW Kramer Junction solar power park located in Boron, California. Improvements were made in the following areas: (a) efficiency of solar energy collection, (b) O ampersand M information management, (c) reliability of solar field flow loop hardware, (d) plant operating strategy, and (e) cost reduction associated with environmental issues. A 37% reduction in annual O ampersand M costs was achieved. Based on the lessons learned, an optimum solar- field O ampersand M plan for future CSP plants is presented. Parabolic trough solar technology is employed at Kramer Junction. However, many of the O ampersand M improvements described in the report are also applicable to CSP plants based on solar power tower or dish/engine concepts

  16. Final Report on the Operation and Maintenance Improvement Program for Concentrating Solar Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Cohen Gilbert E.; Kearney, David W.; Kolb, Gregory J.

    1999-06-01

    This report describes the results of a six-year, $6.3 million project to reduce operation and maintenance (O&M) costs at power plants employing concentrating solar power (CSP) technology. Sandia National Laboratories teamed with KJC Operating Company to implement the O&M Improvement Program. O&M technologies developed during the course of the program were demonstrated at the 150-MW Kramer Junction solar power park located in Boron, California. Improvements were made in the following areas: (a) efficiency of solar energy collection, (b) O&M information management, (c) reliability of solar field flow loop hardware, (d) plant operating strategy, and (e) cost reduction associated with environmental issues. A 37% reduction in annual O&M costs was achieved. Based on the lessons learned, an optimum solar- field O&M plan for future CSP plants is presented. Parabolic trough solar technology is employed at Kramer Junction. However, many of the O&M improvements described in the report are also applicable to CSP plants based on solar power tower or dish/engine concepts.

  17. An Intelligent Robot Programing

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Seong Yong

    2012-01-15

    This book introduces an intelligent robot programing with background of the begging, introduction of VPL, and SPL, building of environment for robot platform, starting of robot programing, design of simulation environment, robot autonomy drive control programing, simulation graphic. Such as SPL graphic programing graphical image and graphical shapes, and graphical method application, application of procedure for robot control, robot multiprogramming, robot bumper sensor programing, robot LRF sencor programing and robot color sensor programing.

  18. System programming languages

    OpenAIRE

    Šmit, Matej

    2016-01-01

    Most operating systems are written in the C programming language. Similar is with system software, for example, device drivers, compilers, debuggers, disk checkers, etc. Recently some new programming languages emerged, which are supposed to be suitable for system programming. In this thesis we present programming languages D, Go, Nim and Rust. We defined the criteria which are important for deciding whether programming language is suitable for system programming. We examine programming langua...

  19. Purely Functional Structured Programming

    OpenAIRE

    Obua, Steven

    2010-01-01

    The idea of functional programming has played a big role in shaping today's landscape of mainstream programming languages. Another concept that dominates the current programming style is Dijkstra's structured programming. Both concepts have been successfully married, for example in the programming language Scala. This paper proposes how the same can be achieved for structured programming and PURELY functional programming via the notion of LINEAR SCOPE. One advantage of this proposal is that m...

  20. An Intelligent Robot Programing

    International Nuclear Information System (INIS)

    Hong, Seong Yong

    2012-01-01

    This book introduces an intelligent robot programing with background of the begging, introduction of VPL, and SPL, building of environment for robot platform, starting of robot programing, design of simulation environment, robot autonomy drive control programing, simulation graphic. Such as SPL graphic programing graphical image and graphical shapes, and graphical method application, application of procedure for robot control, robot multiprogramming, robot bumper sensor programing, robot LRF sencor programing and robot color sensor programing.

  1. Analysis and design of a dish/Stirling system for solar electric generation with a 2.7 kW air-cooled engine; Analisis y diseno de un sistema de generacion electrica termosolar con concentrador de disco parabolico y motor Stirling de 2.7 kW enfriado por aire

    Energy Technology Data Exchange (ETDEWEB)

    Beltran-Chacon, R.; Velazquez-Limon, N. [Universidad Autonoma de Baja California, Baja California (Mexico)]. E-mails: rbeltran1@uabc.edu.mx; nicolas.velazquez@uabc.edu.mx; Sauceda-Carvajal, D. [Universidad Politecnica de Baja California, Baja California (Mexico)]. E-mail: dsaucedac@upbc.edu.mx

    2012-01-15

    This paper presents a mathematical modeling, simulation and design of a solar power system of a parabolic dish with an air-cooled Stirling engine of 2.7 kW. The model used for the solar concentrator, the cavity and the Stirling engine were successfully validated against experimental data. Based on a parametric study, the design of the components of the engine is carried out. The study shows that as system capacity increases, the overall efficiency is limited by the power required by the fan, since the design of the cooler needs greater amounts of heat removal by increasing the air flow without affecting the internal conditions of the process (mass flow of working gas and internal dimensions of the same). The system was optimized and achieves an overall efficiency of solar to electric energy conversion of 26.7%. This study shows that the use of an air-cooled Stirling engine is potentially attractive for power generation at low capacities. [Spanish] Este trabajo presenta un modelado matematico, la simulacion y diseno de un sistema de generacion electrica termosolar de disco parabolico con motor Stirling de 2.7 kW enfriado directamente por aire. El modelo utilizado para el concentrador, la cavidad y el motor Stirling, fueron validados satisfactoriamente con datos experimentales. Con base en un estudio parametrico se realizo el dimensionamiento de los componentes del motor. El estudio realizado muestra que conforme se incrementa la capacidad del sistema, la eficiencia global se ve limitada por la potencia requerida por el ventilador, dado que el diseno del enfriador necesita retirar mayores cantidades de calor aumentando el flujo de aire, sin afectar las condiciones internas del proceso (flujo masico del gas de trabajo y dimensiones internas del mismo). El sistema fue optimizado obteniendo una eficiencia global de conversion de energia solar a electrica de 26.7%. Este estudio muestra que el uso de un motor Stirling enfriado directamente por aire es potencialmente

  2. Applied Energy Program

    Science.gov (United States)

    Science Programs Applied Energy Programs Civilian Nuclear Energy Programs Laboratory Directed Research » Applied Energy Program Applied Energy Program Los Alamos is using its world-class scientific capabilities to enhance national energy security by developing energy sources with limited environmental impact

  3. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Trauma Quality Programs National Trauma Data Bank Trauma Quality Improvement Program Mentoring for Excellence in Trauma Surgery Advanced Trauma Life Support Verification, Review, and Consultation Program for Hospitals ...

  4. Diabetes Prevention Program (DPP)

    Science.gov (United States)

    ... Recruiting Patients & Families Consortia, Networks & Centers Reports & Planning Diabetes Prevention Program (DPP) The NIDDK-sponsored Diabetes Prevention ... Diabetes Prevention Program for those who are eligible. Diabetes Prevention Program (DPP) DPP Goal The DPP looked ...

  5. Research Program Overview

    Science.gov (United States)

    PEER logo Pacific Earthquake Engineering Research Center home about peer news events research products laboratories publications nisee b.i.p. members education FAQs links research Research Program Overview Tall Buildings Initiative Transportation Research Program Lifelines Program Concrete Grand

  6. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Safety Resources About the Patient Education Program The Recovery Room Choosing Wisely Educational Programs Educational Programs Educational ... and practice the skills needed for optimal postoperative recovery. The kit supports the entire surgical team with ...

  7. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Accreditation Program for Breast Centers About NAPBC Accreditation Education NAPBC Standards Cancer Programs News Quality in Geriatric ... Continuous Certification Requirements SSR Login MIPS Resources and Education Quality and Safety Conference Trauma Trauma Programs Trauma ...

  8. Stop smoking support programs

    Science.gov (United States)

    Smokeless tobacco - stop smoking programs; Stop smoking techniques; Smoking cessation programs; Smoking cessation techniques ... You can find out about smoking cessation programs from: Your ... Your employer Your local health department The National Cancer ...

  9. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... and Safety Inspiring Quality Initiative Resources Continuous Quality Improvement ACS Clinical Scholars in Residence AHRQ Safety Program ... Enrollment Webinars ACS NSQIP ACS National Surgical Quality Improvement Program ACS National Surgical Quality Improvement Program About ...

  10. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Quality and Safety Inspiring Quality Initiative Resources Continuous Quality Improvement ACS Clinical Scholars in Residence AHRQ Safety Program ... ISCR Enrollment Webinars ACS NSQIP ACS National Surgical Quality Improvement Program ACS National Surgical Quality Improvement Program About ...

  11. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... ACS Careers at ACS About ACS Career Types Working at ACS ... Education Patients and Family Skills Programs Ostomy Home Skills Program Ostomy Home Skills Program Adult Ostomy ...

  12. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Policy Updates Selected Research Findings Quality Program Initiatives Communications to the Profession Advocacy Advocacy Overview Quality Payment Program QPP Resource Center QPP Resource Center 2018 Information 2017 Information Program Rules Surgeon Specific Registry Metabolic ...

  13. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Military Health System Strategic Partnership Military Health System Strategic Partnership About Excelsior Surgical Society ... Programs Quality Programs Overview About Quality Programs ACS Leadership in Quality ACS Leadership in Quality Setting the ...

  14. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Membership Directory 2017 Annual Meeting 2016 Annual Meeting Women's Committee Mentorship Program Outside Activities ACS Archives Contact ... Accreditation Program for Breast Centers About NAPBC Accreditation Education NAPBC Standards Cancer Programs News Quality in Geriatric ...

  15. Heliostat Manufacturing for near-term markets. Phase II final report

    International Nuclear Information System (INIS)

    1998-01-01

    This report describes a project by Science Applications International Corporation and its subcontractors Boeing/Rocketdyne and Bechtel Corp. to develop manufacturing technology for production of SAIC stretched membrane heliostats. The project consists of three phases, of which two are complete. This first phase had as its goals to identify and complete a detailed evaluation of manufacturing technology, process changes, and design enhancements to be pursued for near-term heliostat markets. In the second phase, the design of the SAIC stretched membrane heliostat was refined, manufacturing tooling for mirror facet and structural component fabrication was implemented, and four proof-of-concept/test heliostats were produced and installed in three locations. The proposed plan for Phase III calls for improvements in production tooling to enhance product quality and prepare increased production capacity. This project is part of the U.S. Department of Energy's Solar Manufacturing Technology Program (SolMaT)

  16. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Verification, Review, and Consultation Program for Hospitals Trauma Systems Consultation Program Trauma Education Achieving Zero Preventable Deaths Conference Publications and Posters ...

  17. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... in Trauma Surgery Advanced Trauma Life Support Verification, Review, and Consultation Program for Hospitals Trauma Systems Consultation Program Trauma Education Achieving Zero Preventable Deaths ...

  18. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Canada) International Fellows Associate Fellows Residents Medical Students Affiliate Members ACS Insurance Programs ACS Discount Programs FACS Resources Career Connection Update ...

  19. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Validation Programs Accreditation, Verification, and Validation Programs Accredited Education Institutes ... Entering Resident Readiness Assessment Evidence-Based Decisions in ...

  20. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... National Accreditation Program for Breast Centers About NAPBC Accreditation Education NAPBC Standards Cancer Programs News Quality in Geriatric Surgery Coalition for Quality in Geriatric ...

  1. American Contact Dermatitis Society Contact Allergy Management Program: An Epidemiologic Tool to Quantify Ingredient Usage.

    Science.gov (United States)

    Scheman, Andrew; Severson, David

    2016-01-01

    The usage prevalence of ingredients in topical products is important to dermatologists and industry. To determine the prevalence of methylisothiazolinone (MI) in various types of consumer products The Contact Allergy Management Program (CAMP) database was mapped and sorted in spreadsheet format to determine the prevalence of MI in various types of consumer products. Methylisothiazolinone was found in 13.2% of 4660 total products in CAMP. High usage of MI was seen in dishwashing products (64%), shampoos (53%), bathroom/kitchen/all-purpose cleaners (47%), hair conditioners (45%), hair dyes (43%), laundry additives/fresheners/softeners (30%), soaps/cleansers (29%), and surface cleaners/disinfectants (27%). Of the products containing MI, MI alone (without methylchloroisothiazolinone) was most common in makeup products (100%), cleaning/dish/laundry products (>99%), moisturizers (82%), shaving products (78%), sunscreens (71%), and antiaging products (67%). The American Contact Dermatitis Society's CAMP is a valuable tool to collect epidemiologic data on the incidence of specific ingredient usage in various types of topical products.

  2. National Transuranic Program Charter

    International Nuclear Information System (INIS)

    1994-10-01

    The National Transuranic Program Plan and Charter describes the functional elements of the National TRU Program, organizational relationships, programmatic responsibilities, division of work scope among the various DOE organizations that comprise the program, and program baselines against which overall progress will be measured. The charter defines the authorities and responsibilities of various organizations involved in the management of TRU waste throughout the DOE complex

  3. Cavity design programs

    International Nuclear Information System (INIS)

    Nelson, E.M.

    1996-01-01

    Numerous computer programs are available to help accelerator physicists and engineers model and design accelerator cavities and other microwave components. This article discusses the problems these programs solve and the principles upon which these programs are based. Some examples of how these programs are used in the design of accelerator cavities are also given

  4. Programs as Data Objects

    DEFF Research Database (Denmark)

    This book constitutes the refereed proceedings of the Second Symposium on Programs as Data Objects, PADO 2001, held in Aarhus, Denmark, in May 2001. The 14 revised full papers presented were carefully reviewed and selected from 30 submissions. Various aspects of looking at programs as data objects...... are covered from the point of view of program analysis, program transformation, computational complexity, etc....

  5. The Cybernetic Writing Program.

    Science.gov (United States)

    Lowe, Kelly Fisher

    This paper looks at the role of a Writing Program Administrator, and applies the idea of a cybernetic system to the administration of the program. In this cybernetic model, the Writing Program Administrator (WPA) works as both a problem solver and problem causer, with the responsibility of keeping the program in proper balance. A cybernetic…

  6. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Advocacy Efforts Cancer Liaison Program Cancer Programs Conference Clinical Research Program Commission on Cancer National Accreditation Program for ... and Safety Conference ACS Clinical Scholars in Residence Clinical Trials ... Health Services Research Methods Course Surgeon Specific Registry Trauma Education Trauma ...

  7. Maintenance procedure upgrade programs

    International Nuclear Information System (INIS)

    Campbell, J.J.; Zimmerman, C.M.

    1988-01-01

    This paper describes a systematic approach to upgrading nuclear power plant maintenance procedures. The approach consists of four phases: diagnosis, program planning, program implementation, and program evaluation. Each phase is explained as a series of steps to ensure that all factors in a procedure upgrade program are considered

  8. Employee Assistance Programs.

    Science.gov (United States)

    Levine, Hermine Zagat

    1985-01-01

    The author reports company responses to a questionnaire concerning employee assistance programs (EAP). Answers concern EAP structure, staff training, use of outside consultant, services provided by EAPs, program administration, employee confidence in EAPs, advertising the program, program philosophy, problems encountered by EAP users, coverage and…

  9. Environmental conditions analysis program

    International Nuclear Information System (INIS)

    Holten, J.

    1991-01-01

    The PC-based program discussed in this paper has the capability of determining the steady state temperatures of environmental zones (rooms). A program overview will be provided along with examples of formula use. Required input and output from the program will also be discussed. Specific application of plant monitored temperatures and utilization of this program will be offered. The presentation will show how the program can project individual room temperature profiles without continual temperature monitoring of equipment. A discussion will also be provided for the application of the program generated data. Evaluations of anticipated or planned plant modifications and the use of the subject program will also be covered

  10. C++ Programming Language

    Science.gov (United States)

    Shaykhian, Gholam Ali

    2007-01-01

    C++ Programming Language: The C++ seminar covers the fundamentals of C++ programming language. The C++ fundamentals are grouped into three parts where each part includes both concept and programming examples aimed at for hands-on practice. The first part covers the functional aspect of C++ programming language with emphasis on function parameters and efficient memory utilization. The second part covers the essential framework of C++ programming language, the object-oriented aspects. Information necessary to evaluate various features of object-oriented programming; including encapsulation, polymorphism and inheritance will be discussed. The last part of the seminar covers template and generic programming. Examples include both user defined and standard templates.

  11. Federal Wind Energy Program. Program summary. [USA

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-01-01

    The objective of the Federal Wind Energy Program is to accelerate the development of reliable and economically viable wind energy systems and enable the earliest possible commercialization of wind power. To achieve this objective for small and large wind systems requires advancing the technology, developing a sound industrial technology base, and addressing the non-technological issues which could deter the use of wind energy. This summary report outlines the projects being supported by the program through FY 1977 toward the achievement of these goals. It also outlines the program's general organization and specific program elements.

  12. An Analysis of Programming Beginners' Source Programs

    Science.gov (United States)

    Matsuyama, Chieko; Nakashima, Toyoshiro; Ishii, Naohiro

    The production of animations was made the subject of a university programming course in order to make students understand the process of program creation, and so that students could tackle programming with interest. In this paper, the formats and composition of the programs which students produced were investigated. As a result, it was found that there were a lot of problems related to such matters as how to use indent, how to apply comments and functions etc. for the format and the composition of the source codes.

  13. Introduction to parallel programming

    CERN Document Server

    Brawer, Steven

    1989-01-01

    Introduction to Parallel Programming focuses on the techniques, processes, methodologies, and approaches involved in parallel programming. The book first offers information on Fortran, hardware and operating system models, and processes, shared memory, and simple parallel programs. Discussions focus on processes and processors, joining processes, shared memory, time-sharing with multiple processors, hardware, loops, passing arguments in function/subroutine calls, program structure, and arithmetic expressions. The text then elaborates on basic parallel programming techniques, barriers and race

  14. Programming with joystick

    OpenAIRE

    Banič, Nejc

    2014-01-01

    In this thesis, we implemented a way of programming by means of gaming accessories. The main reason is that to show a diferent way of developing programs, because vast majority of programers are using two input / output devices: keyboard and mouse. These two devices have become standard and will definitely remain so in the future. For our implementation, we used high-level programming language Java and NetBeans integrated development environment. The program is actually a ...

  15. Multiobjective programming and planning

    CERN Document Server

    Cohon, Jared L

    2004-01-01

    This text takes a broad view of multiobjective programming, emphasizing the methods most useful for continuous problems. It reviews multiobjective programming methods in the context of public decision-making problems, developing each problem within a context that addresses practical aspects of planning issues. Topics include a review of linear programming, the formulation of the general multiobjective programming problem, classification of multiobjective programming methods, techniques for generating noninferior solutions, multiple-decision-making methods, multiobjective analysis of water reso

  16. Technology Commercialization Program 1991

    Energy Technology Data Exchange (ETDEWEB)

    1991-11-01

    This reference compilation describes the Technology Commercialization Program of the Department of Energy, Defense Programs. The compilation consists of two sections. Section 1, Plans and Procedures, describes the plans and procedures of the Defense Programs Technology Commercialization Program. The second section, Legislation and Policy, identifies legislation and policy related to the Program. The procedures for implementing statutory and regulatory requirements are evolving with time. This document will be periodically updated to reflect changes and new material.

  17. Stochastic integer programming by dynamic programming

    NARCIS (Netherlands)

    Lageweg, B.J.; Lenstra, J.K.; Rinnooy Kan, A.H.G.; Stougie, L.; Ermoliev, Yu.; Wets, R.J.B.

    1988-01-01

    Stochastic integer programming is a suitable tool for modeling hierarchical decision situations with combinatorial features. In continuation of our work on the design and analysis of heuristics for such problems, we now try to find optimal solutions. Dynamic programming techniques can be used to

  18. Analyzing Array Manipulating Programs by Program Transformation

    Science.gov (United States)

    Cornish, J. Robert M.; Gange, Graeme; Navas, Jorge A.; Schachte, Peter; Sondergaard, Harald; Stuckey, Peter J.

    2014-01-01

    We explore a transformational approach to the problem of verifying simple array-manipulating programs. Traditionally, verification of such programs requires intricate analysis machinery to reason with universally quantified statements about symbolic array segments, such as "every data item stored in the segment A[i] to A[j] is equal to the corresponding item stored in the segment B[i] to B[j]." We define a simple abstract machine which allows for set-valued variables and we show how to translate programs with array operations to array-free code for this machine. For the purpose of program analysis, the translated program remains faithful to the semantics of array manipulation. Based on our implementation in LLVM, we evaluate the approach with respect to its ability to extract useful invariants and the cost in terms of code size.

  19. Program reference schedule baseline

    International Nuclear Information System (INIS)

    1986-07-01

    This Program Reference Schedule Baseline (PRSB) provides the baseline Program-level milestones and associated schedules for the Civilian Radioactive Waste Management Program. It integrates all Program-level schedule-related activities. This schedule baseline will be used by the Director, Office of Civilian Radioactive Waste Management (OCRWM), and his staff to monitor compliance with Program objectives. Chapter 1 includes brief discussions concerning the relationship of the PRSB to the Program Reference Cost Baseline (PRCB), the Mission Plan, the Project Decision Schedule, the Total System Life Cycle Cost report, the Program Management Information System report, the Program Milestone Review, annual budget preparation, and system element plans. Chapter 2 includes the identification of all Level 0, or Program-level, milestones, while Chapter 3 presents and discusses the critical path schedules that correspond to those Level 0 milestones

  20. Programming Models in HPC

    Energy Technology Data Exchange (ETDEWEB)

    Shipman, Galen M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-06-13

    These are the slides for a presentation on programming models in HPC, at the Los Alamos National Laboratory's Parallel Computing Summer School. The following topics are covered: Flynn's Taxonomy of computer architectures; single instruction single data; single instruction multiple data; multiple instruction multiple data; address space organization; definition of Trinity (Intel Xeon-Phi is a MIMD architecture); single program multiple data; multiple program multiple data; ExMatEx workflow overview; definition of a programming model, programming languages, runtime systems; programming model and environments; MPI (Message Passing Interface); OpenMP; Kokkos (Performance Portable Thread-Parallel Programming Model); Kokkos abstractions, patterns, policies, and spaces; RAJA, a systematic approach to node-level portability and tuning; overview of the Legion Programming Model; mapping tasks and data to hardware resources; interoperability: supporting task-level models; Legion S3D execution and performance details; workflow, integration of external resources into the programming model.

  1. Revealing the programming process

    DEFF Research Database (Denmark)

    Bennedsen, Jens; Caspersen, Michael Edelgaard

    2005-01-01

    One of the most important goals of an introductory programming course is that the students learn a systematic approach to the development of computer programs. Revealing the programming process is an important part of this; however, textbooks do not address the issue -- probably because...... the textbook medium is static and therefore ill-suited to expose the process of programming. We have found that process recordings in the form of captured narrated programming sessions are a simple, cheap, and efficient way of providing the revelation.We identify seven different elements of the programming...

  2. General edition program

    International Nuclear Information System (INIS)

    Vaturi, Sylvain

    1969-01-01

    Computerized edition is essential for data processing exploitation. When a more or less complex edition program is required for each task, then the need for a general edition program become obvious. The aim of this study is to create a general edition program. Universal programs are capable to execute numerous and varied tasks. For a more precise processing, the execution of which is frequently required, the use of a specialized program is preferable because, contradictory to the universal program, it goes straight to the point [fr

  3. Employee assistance programs: history and program description.

    Science.gov (United States)

    Gilbert, B

    1994-10-01

    1. The history and development of Employee Assistance Programs (EAPs) can be traced back to the 1800s. There are currently over 10,000 EAPs in the United States. 2. Standards for program accreditation and counselor certification have been established for EAPs. The "core technology of Employee Assistance Programs" includes identification of behavioural problems based on job performance issues, expert consultation with supervisors, appropriate use of constructive confrontation, microlinkages with treatment providers and resources, macrolinkages between providers, resources, and work organizations, focus on substance abuse, and evaluation of employee success based on job performance. 3. Some EAPs take a broad brush approach, and incorporate health promotion and managed care functions.

  4. HUD Program Income Limits

    Data.gov (United States)

    Department of Housing and Urban Development — Income limits used to determine the income eligibility of applicants for assistance under three programs authorized by the National Housing Act. These programs are...

  5. Astron Program final report

    International Nuclear Information System (INIS)

    Briggs, R.J.; Hester, R.E.; Porter, G.D.; Sherwood, W.A.; Spoerlein, R.; Stallard, B.W.; Taska, J.; Weiss, P.B.

    1975-01-01

    This report describes important experimental results obtained in the last two years of the Astron Program, an LLL controlled nuclear fusion program which terminated in 1973. Little theoretical work is included, but an extensive bibliography is given

  6. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Quality Standard Optimal Resources for Surgical Quality and Safety Inspiring Quality Initiative Resources Continuous Quality Improvement ACS Clinical Scholars in Residence AHRQ Safety Program for ISCR AHRQ Safety Program for ISCR ...

  7. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Member Fellows International Fellows Associate Fellows Residents Medical Students Affiliate Members Fees and Dues Realize the Potential ... and Canada) International Fellows Associate Fellows Residents Medical Students Affiliate Members ACS Insurance Programs ACS Discount Programs ...

  8. LOADING SIMULATION PROGRAM C

    Science.gov (United States)

    LSPC is the Loading Simulation Program in C++, a watershed modeling system that includes streamlined Hydrologic Simulation Program Fortran (HSPF) algorithms for simulating hydrology, sediment, and general water quality

  9. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Program Trauma Education Achieving Zero Preventable Deaths Conference Publications and Posters National Trauma System Injury Prevention and ... Division of Education ACS Education and Training Courses Publications Resources Education Program Videos Contact Us Clinical Congress ...

  10. National Toxicology Program

    Science.gov (United States)

    ... NTP? NTP develops and applies tools of modern toxicology and molecular biology to identify substances in the ... depend on for decisions that matter. The National Toxicology Program provides the scientific basis for programs, activities, ...

  11. Veterans Choice Program

    Data.gov (United States)

    Department of Veterans Affairs — If you are already enrolled in VA health care, the Choice Program allows you to receive health care within your community. Using this program does NOT impact your...

  12. French plutonium management program

    International Nuclear Information System (INIS)

    Greneche, D.

    2002-01-01

    The French plutonium management program is summarized in this paper. The program considers nuclear generation as a major component of national electric power supply and includes the reprocessing of the spent fuel. (author)

  13. Entrez Programming Utilities

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Entrez Programming Utilities (E-utilities) are a set of eight server-side programs that provide a stable interface into the Entrez query and database system at...

  14. LOADING SIMULATION PROGRAM C

    Data.gov (United States)

    U.S. Environmental Protection Agency — LSPC is the Loading Simulation Program in C++, a watershed modeling system that includes streamlined Hydrologic Simulation Program Fortran (HSPF) algorithms for...

  15. Coalbed Methane Outreach Program

    Science.gov (United States)

    Coalbed Methane Outreach Program, voluntary program seeking to reduce methane emissions from coal mining activities. CMOP promotes profitable recovery/use of coal mine methane (CMM), addressing barriers to using CMM instead of emitting it to atmosphere.

  16. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... JACS Jobs Events Find a Surgeon Patients and Family Contact My Profile Shop ( 0 ) Cart Donate American College of Surgeons Education Patients and Family Skills Programs Ostomy Home Skills Program Ostomy Home ...

  17. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... SESAP Sampler SRGS Resources in Surgical Education ACS Fundamentals of Surgery Curriculum Mastery in General Surgery Program ... Communications to the Profession Advocacy Advocacy Overview Quality Payment Program QPP Resource Center QPP Resource Center 2018 ...

  18. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Profession Member Benefits About Member Benefits About Member Benefits Fellows (US and Canada) International Fellows Associate Fellows Residents Medical Students Affiliate Members ACS Insurance Programs ACS Discount Programs ...

  19. STEM Education Programs

    Science.gov (United States)

    & Development (LDRD) National Security Education Center (NSEC) Office of Science Programs Richard P Databases National Security Education Center (NSEC) Center for Nonlinear Studies Engineering Institute Scholarships STEM Education Programs Teachers (K-12) Students (K-12) Higher Education Regional Education

  20. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Program State Legislation Tracked by the College Maintenance of Certification Quality Quality Quality Electronic Health Records (EHR) Incentive Program Physician Quality Reporting System Value-Based Payment Modifier Quality and Resource Use ...

  1. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... About Quality Programs ACS Leadership in Quality ACS Leadership in Quality Setting the Quality Standard Optimal Resources for Surgical Quality and Safety Inspiring Quality Initiative Resources Continuous Quality Improvement ACS Clinical Scholars in Residence AHRQ Safety Program ...

  2. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... My OR EHR Incentive Program Global Codes and Data Collection Patient Opioid Use New Medicare Card Project Medicare ... self-care checklist Evaluation (Complete the Ostomy Patient Survey . We need your opinion!) Program outcomes The ACS ...

  3. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Careers at ACS Careers at ACS About ACS Career Types Working at ACS ... American College of Surgeons Education Patients and Family Skills Programs Ostomy Home Skills Program Ostomy Home Skills ...

  4. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Be a YFA Leader Meetings and Events YFA Mentor Programs YFA Speakers Bureau Top 10 Reasons to ... National Trauma Data Bank Trauma Quality Improvement Program Mentoring for Excellence in Trauma Surgery Advanced Trauma Life ...

  5. Understanding Participation in Programs.

    Science.gov (United States)

    Hanson, Alan L.

    1991-01-01

    Adherence to program planning principles does not guarantee participation. Attention must be paid to characteristics that make a program responsive: target audience, promotion and marketing, competition, and logistics. (SK)

  6. Materials Sciences Programs

    International Nuclear Information System (INIS)

    1977-01-01

    A compilation and index of the ERDA materials sciences program is presented. This compilation is intended for use by administrators, managers, and scientists to help coordinate research and as an aid in selecting new programs

  7. ISTEF Laser Radar Program

    National Research Council Canada - National Science Library

    Stryjewski, John

    1998-01-01

    The BMDO Innovative Science and Technology Experimentation Facility (BMDO/ISTEF) laser radar program is engaged in an ongoing program to develop and demonstrate advanced laser radar concepts for Ballistic Missile Defense (BMD...

  8. Programming Language Paradigms

    OpenAIRE

    Felician ALECU

    2013-01-01

    This paper's goal is to briefly explain the basic theory behind programming languages and their history while taking a close look at different programming paradigms that are used today as well as describing their differences, benefits, and drawbacks

  9. ICASE Computer Science Program

    Science.gov (United States)

    1985-01-01

    The Institute for Computer Applications in Science and Engineering computer science program is discussed in outline form. Information is given on such topics as problem decomposition, algorithm development, programming languages, and parallel architectures.

  10. Ecosystem Analysis Program

    International Nuclear Information System (INIS)

    Burgess, R.L.

    1978-01-01

    Progress is reported on the following research programs: analysis and modeling of ecosystems; EDFB/IBP data center; biome analysis studies; land/water interaction studies; and computer programs for development of models

  11. Python to learn programming

    Science.gov (United States)

    Bogdanchikov, A.; Zhaparov, M.; Suliyev, R.

    2013-04-01

    Today we have a lot of programming languages that can realize our needs, but the most important question is how to teach programming to beginner students. In this paper we suggest using Python for this purpose, because it is a programming language that has neatly organized syntax and powerful tools to solve any task. Moreover it is very close to simple math thinking. Python is chosen as a primary programming language for freshmen in most of leading universities. Writing code in python is easy. In this paper we give some examples of program codes written in Java, C++ and Python language, and we make a comparison between them. Firstly, this paper proposes advantages of Python language in relation to C++ and JAVA. Then it shows the results of a comparison of short program codes written in three different languages, followed by a discussion on how students understand programming. Finally experimental results of students' success in programming courses are shown.

  12. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Meetings and Events Scholarships, Competitions, Awards, and Project Work Top 10 Reasons to Participate Grand Rounds Webinar ... Accreditation Program for Breast Centers About NAPBC Accreditation Education NAPBC Standards Cancer Programs News Quality in Geriatric ...

  13. Modeling EERE deployment programs

    Energy Technology Data Exchange (ETDEWEB)

    Cort, K. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hostick, D. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Belzer, D. B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Livingston, O. V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2007-11-01

    The purpose of the project was to identify and characterize the modeling of deployment programs within the EERE Technology Development (TD) programs, address possible improvements to the modeling process, and note gaps in knowledge for future research.

  14. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... About ACS NSQIP Join ACS NSQIP Now Collaboratives Hospital Compare Quality and Safety Conference Participant Use Data ... Life Support Verification, Review, and Consultation Program for Hospitals Trauma Systems Consultation Program Trauma Education Achieving Zero ...

  15. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Centers National Cancer Database National Accreditation Program for Rectal Cancer Oncology Medical Home Accreditation Program Stereotactic Breast ... collaboration with the American Society of Colon and Rectal Surgeons (ASCRS), American Urological Association (AUA), Certified Enterostomal ...

  16. Youth Suicide Prevention Programs

    Science.gov (United States)

    Kalafat, John

    2006-01-01

    Youth suicide prevention programs are described that promote the identification and referral of at-risk youth, address risk factors, and promote protective factors. Emphasis is on programs that are both effective and sustainable in applied settings.

  17. Crab Rationalization Permit Program

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Crab Rationalization Program (Program) allocates BSAI crab resources among harvesters, processors, and coastal communities. The North Pacific Fishery Management...

  18. Dental Assisting Program Standards.

    Science.gov (United States)

    Georgia Univ., Athens. Dept. of Vocational Education.

    This publication contains statewide standards for the dental assisting program in Georgia. The standards are divided into 12 categories: foundations (philosophy, purpose, goals, program objectives, availability, evaluation); admissions (admission requirements, provisional admission requirements, recruitment, evaluation and planning); program…

  19. USSR imploding liner program

    International Nuclear Information System (INIS)

    Shearer, J.W.

    1975-01-01

    A summary is given of the history and rationale of the USSR program to implode metallic liners for the fusion program. The explosive driven, magnetic drive, and compressed gas driven research is reviewed. (MOW)

  20. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Associate Fellows Residents Medical Students Affiliate Members ACS Insurance Programs ACS Discount Programs FACS Resources Career Connection ... and Awards Overview Scholarships, Fellowships, and Awards Overview Health Policy Scholarships Scholarships for International Surgeons Research Scholarships ...

  1. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Class Clinical Congress 2018 Events at Clinical Congress Child Care at Clinical Congress Info for International Attendees ... Accreditation Program for Breast Centers About NAPBC Accreditation Education NAPBC Standards Cancer Programs News Quality in Geriatric ...

  2. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... You Want to Be a Surgeon Resident Resources Teaching Resources Online Guide to Choosing a Surgical Residency ... Research Findings Quality Program Initiatives Communications to the Profession Advocacy Advocacy Overview Quality Payment Program QPP Resource ...

  3. Reactive Programming in Java

    CERN Document Server

    CERN. Geneva

    2017-01-01

    Reactive Programming in gaining a lot of excitement. Many libraries, tools, and frameworks are beginning to make use of reactive libraries. Besides, applications dealing with big data or high frequency data can benefit from this programming paradigm. Come to this presentation to learn about what reactive programming is, what kind of problems it solves, how it solves them. We will take an example oriented approach to learning the programming model and the abstraction.

  4. Photovoltaic systems. Program summary

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-12-01

    Each of the Department of Energy's Photovoltaic Systems Program projects funded and/or in existence during fiscal year 1978 (October 1, 1977 through September 30, 1978) are described. The project sheets list the contractor, principal investigator, and contract number and funding and summarize the programs and status. The program is divided into various elements: program assessment and integration, research and advanced development, technology development, system definition and development, system application experiments, and standards and performance criteria. (WHK)

  5. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... State Requirements Contact Online Education Accreditation, Verification, and Validation Accreditation, Verification, and Validation Programs Accreditation, Verification, and ...

  6. Morning Programs Revisited.

    Science.gov (United States)

    Black, Susan

    1993-01-01

    Like British morning programs of recent decades, upstate New York program encourages parents and community residents to get involved in children's education. Parents and community residents--watercolor artists, auto mechanics, doll collectors, and others--are welcomed and valued in schools. Program's purpose is learning, not entertainment. Topics…

  7. Customer Service Programming

    Science.gov (United States)

    1982-01-01

    Use of computer program STRCMACS has enabled Illinois Bell Telephone, a subsidiary of American Telephone and Telegraph to cut software development costs about 10 percent by reducing program maintenance and by allowing the department to bring other software into operation more quickly. It has also been useful in company training of programming staff.

  8. Maine's Employability Skills Program

    Science.gov (United States)

    McMahon, John M.; Wolffe, Karen E.; Wolfe, Judy; Brooker, Carrie

    2013-01-01

    This Practice Report describes the development and implementation of the "Maine Employability Skills Program," a model employment program developed by the Maine Division for the Blind and Visually Impaired (DBVI). The program was designed to support the efforts of the chronically unemployed or underemployed. These consumers were either…

  9. An Interdistrict Transfer Program

    Science.gov (United States)

    Gross, Norman

    1975-01-01

    This testimony, before the May 1974 public hearings of the New York City Commission on Human Rights by the Administrator, Urban-Suburban Transfer Program and Inter district Transfer Program, West Irondequoit School District, New York, reviews a program which began with 25 minority group youngsters from one racially-imbalanced Rochester school…

  10. The Trailblazer Program

    Science.gov (United States)

    Trefney, Charles J.

    1999-01-01

    This paper presents the "Three Pillars of Success" for the Trailblazer Program. The topics include: 1) The "Rocket Equation" for SSTO (Single Stage To Orbit); 2) The Rocket I* Barrier; 3) Rocket-Based Combined-Cycle Engine; 4) Potential for Reusability; 5) Factors Mitigating RBCC Performance; 6) The "Trailblazer" Program; 7) Trailblazer Performance Goals; 8) Trailblazer Reference Vehicle; and 9) Trailblazer Program Architecture.

  11. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Trauma Programs About Trauma Programs Violence Prevention BleedingControl.org Trauma Quality Programs National Trauma Data Bank Trauma ... 5000 (F) 312-202-5001 (E) postmaster@facs.org Copyright © 1996-2018 by the American College of ...

  12. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Ostomy Home Skills Program Ostomy Home Skills Program Adult Ostomy Pediatric Ostomy Programa de Destrezas para manejo Doméstico de Ostomía Ostomy Home Skills Program Adult Ostomy Pediatric Ostomy Programa de Destrezas para manejo ...

  13. NCSU Reactor Sharing Program

    International Nuclear Information System (INIS)

    Perez, P.B.

    1993-01-01

    The Nuclear Reactor Program at North Carolina State University provides the PULSTAR Research Reactor and associated facilities to eligible institutions with support, in part, from the Department of Energy Reactor Sharing Program. Participation in the NCSU Reactor Sharing Program continues to increase steadily with visitors ranging from advance high school physics and chemistry students to Ph.D. level research from neighboring universities

  14. Programs, interfaces and components

    NARCIS (Netherlands)

    Bergstra, J.A.; Loots, M.E.

    The jump instruction is considered essential for an adequate theoretical understanding of imperative sequential programming. Using atomic actions and tests as a basis we outline an algebra of programs, denoted PGA, which captures the crux of sequential programming. PGA provides an ontology for

  15. Trends in Multicultural Programming.

    Science.gov (United States)

    Mylopoulos, Chryss

    1985-01-01

    Outlines basic principles and philosophy behind library multicultural programs and provides brief overview of development of such programs in Canadian libraries. Programing themes (cultural identity, contribution of ethnocultural groups to Canadian society, interpretation of multiculturalism as social policy) and suggestions for integrating…

  16. Special Milk Program

    Science.gov (United States)

    US Department of Agriculture, 2009

    2009-01-01

    The Special Milk Program provides milk to children in schools, child care institutions and eligible camps that do not participate in other Federal child nutrition meal service programs. The program reimburses schools and institutions for the milk they serve. In 2008, 4,676 schools and residential child care institutions participated, along with…

  17. YRE Program Guide.

    Science.gov (United States)

    California State Dept. of Education, Sacramento. Div. of School Facilities Planning.

    This report examines single- and multi-track educational programs as found in California's public school system, explores the pros and cons of using year-round education (YRE) programs, and how to implement these programs. Each year-round tracking system is detailed using each of their calendars in a side-by-side comparison along with the…

  18. Modern programming language

    Science.gov (United States)

    Feldman, G. H.; Johnson, J. A.

    1980-01-01

    Structural-programming language is especially-tailored for producing assembly language programs for MODCOMP II and IV mini-computes. Modern programming language consists of set of simple and powerful control structures that include sequencing alternative selection, looping, sub-module linking, comment insertion, statement continuation, and compilation termination capabilities.

  19. Programming the BBC micro

    CERN Document Server

    Ferguson, John D; Macari, Louie; Williams, Peter H

    1983-01-01

    Programming the BBC Micro is a 12-chapter book that begins with a description of the BBC microcomputer, its peripheral, and faults. Subsequent chapters focus on practice in programming, program development, graphics, words, numbers, sound, bits, bytes, and assembly language. The interfacing, file handling, and detailed description of BBC microcomputer are also shown.

  20. Weatherization and Intergovernmental Program - Weatherization Assistance Program

    Energy Technology Data Exchange (ETDEWEB)

    None

    2010-06-01

    The U.S. Department of Energy’s (DOE) Weatherization Assistance Program reduces energy costs for low-income households by increasing the energy efficiency of their homes, while ensuring their health and safety.

  1. Equipment qualification research program: program plan

    International Nuclear Information System (INIS)

    Dong, R.G.; Smith, P.D.

    1982-01-01

    The Lawrence Livermore National Laboratory (LLNL) under the sponsorship of the US Nuclear Regulatory Commission (NRC) has developed this program plan for research in equipment qualification (EQA). In this report the research program which will be executed in accordance with this plan will be referred to as the Equipment Qualification Research Program (EQRP). Covered are electrical and mechanical equipment under the conditions described in the OBJECTIVE section of this report. The EQRP has two phases; Phase I is primarily to produce early results and to develop information for Phase II. Phase I will last 18 months and consists of six projects. The first project is program management. The second project is responsible for in-depth evaluation and review of EQ issues and EQ processes. The third project is responsible for detailed planning to initiate Phase II. The remaining three projects address specific equipment; i.e., valves, electrical equipment, and a pump

  2. Scallop License Limitation Program (SLLP) Permit Program

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — A federal Scallop License Limitation Program (SLLP) license is required onboard any vessel deployed in scallop fisheries in Federal waters off Alaska (except for...

  3. Clean Coal Technology Programs: Program Update 2009

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-10-01

    The purpose of the Clean Coal Technology Programs: Program Update 2009 is to provide an updated status of the U.S. Department of Energy (DOE) commercial-scale demonstrations of clean coal technologies (CCT). These demonstrations have been performed under the Clean Coal Technology Demonstration Program (CCTDP), the Power Plant Improvement Initiative (PPII), and the Clean Coal Power Initiative (CCPI). Program Update 2009 provides: (1) a discussion of the role of clean coal technology demonstrations in improving the nation’s energy security and reliability, while protecting the environment using the nation’s most abundant energy resource—coal; (2) a summary of the funding and costs of the demonstrations; and (3) an overview of the technologies being demonstrated, along with fact sheets for projects that are active, recently completed, or recently discontinued.

  4. Programming in COBOL

    CERN Document Server

    Lancaster, G T

    2014-01-01

    Programming in COBOL is a simple yet concise how-to book that teaches the programming language in a short yet effective step-by-step manner, which can be easily understood by anyone with sufficient knowledge in information technology. Covering first the advantages of COBOL over other programming languages, the book discusses COBOL's divisions - identification, environment, procedure, and data, and then describes the testing of the COBOL source programs and program questions. The book is valuable for those who wish to learn basic COBOL language, but do not have the time to take manufacturers' o

  5. Energy research program 83

    International Nuclear Information System (INIS)

    1983-01-01

    The energy research program 83 (EFP-83) is prepared by the Danish Ministry of Energy in order to continue the extension of the Danish energy research and development started through the former Trade Ministry's programs EM-1 (1976) and EM-2 (1978), and the Ministry of Energy's programs EFP-80, EFP-81 and EFP-82. The new program is a continuation of the activities in the period 1983-85 with a total budget of 111 mio. DKK. The program gives a brief description of background, principles, organization and financing, and a detailed description of each research area. (ln)

  6. Energy research program 85

    International Nuclear Information System (INIS)

    1985-01-01

    The energy research program 85 (EFP-85) is prepared by the Danish Ministry of Energy in order to continue the extension of the Danish energy research and development started through the former Trade Ministry's programs EM-1 (1976) and EM-2 (1978), and Ministry of Energy's programs EFP-80, EFP-81, EFP-82, EFP-83, and EFP-84. The new program is a continuation of the activities in the period 1985-87 with a total budget of 110 mio. DKK. The program gives a brief description of background, principles, organization and financing, and a detailed description of each research area. (ln)

  7. Energy research program 82

    International Nuclear Information System (INIS)

    1982-01-01

    The energy research program 82 (EFP-82) is prepared by the Danish ministry of energy in order to continue the extension of the Danish energy research and development started through the former trade ministry's programs EM-1 (1976) and EM-2 (1978), and the energy ministry's programs EFP-80 and EFP-81. The new program is a continuation of the activities in the period 1982-84 with a total budget of 100 mio.Dkr. The program gives a brief description of background, principles, organization and financing, and a detailed description of each research area. (BP)

  8. Energy research program 86

    International Nuclear Information System (INIS)

    1986-01-01

    The energy research program 86 (EFP-86) is prepared by the Danish Ministry of Energy in order to continue the extension of the Danish energy research and development started through the former Trade Ministry's programs EM-1 (1976) and EM-2 (1978), and the Ministry of Energy's programs EFP-80, EFP-81, EFP-82, EFP-83, EFP-84, and EFP-85. The new program is a continuation of the activities in the period 1986-88 with a total budget of 116 mio. DKK. The program gives a brief description of background, principles, organization and financing, and a detailed description of each research area. (ln)

  9. Energy research program 84

    International Nuclear Information System (INIS)

    1984-01-01

    The energy research program 84 (EFP-84) is prepared by the Danish Ministry of Energy in order to continue the extension of the Danish energy research and development started through the former Trade Ministry's programs EM-1 (1976) and EM-2 (1978), and the Ministry of Energy's programs EFP-80, EFP-81, EFP-82 and EFP-83. The new program is a continuation of the activities in the period 1984-86 with a total budget of 112 mio. DKK. The program gives a brief description of background, principles, organization and financing, and a detailed description of each research area. (ln)

  10. Mixed language programming

    International Nuclear Information System (INIS)

    Burow, Burkhard D.

    1996-01-01

    Computing in the next millennium will be using software from this millennium. Programming languages evolve and new ones continue to be created. The use of legacy code demonstrates why some present and future applications may span programming languages. Even a completely new application may mix programming languages, if it allows its components to be more conveniently expressed. Given the need, mixed language programming should be easy and robust. By resolving a variety of difficulties, the well established cfortran.h package provides, the desired convenient interface across the C and Fortran programming languages, as demonstrated using CERN's Book. (author)

  11. Surplus Facilities Management Program

    International Nuclear Information System (INIS)

    Coobs, J.H.

    1983-01-01

    This is the second of two programs that are concerned with the management of surplus facilities. The facilities in this program are those related to commercial activities, which include the three surplus experimental and test reactors [(MSRE, HRE-2, and the Low Intensity Test Reactor (LITR)] and seven experimental loops at the ORR. The program is an integral part of the Surplus Facilities Management Program, which is a national program administered for DOE by the Richland Operations Office. Very briefly reported here are routine surveillance and maintenance of surplus radioactively contaminated DOE facilities awaiting decommissioning

  12. C++ how to program

    CERN Document Server

    Deitel, Paul J

    2014-01-01

    This best-selling comprehensive text is aimed at readers with little or no programming experience. It teaches programming by presenting the concepts in the context of full working programs and takes an early-objects approach. The authors emphasize achieving program clarity through structured and object-oriented programming, software reuse and component-oriented software construction. The Ninth Edition encourages students to connect computers to the community, using the Internet to solve problems and make a difference in our world. All content has been carefully fine-tuned in response to a team of distinguished academic and industry reviewers.

  13. SSCL quality program overview

    International Nuclear Information System (INIS)

    Hedderick, R.V.; Threatt, D.C.

    1992-01-01

    The Quality Program for the Superconducing Super Collider Laboratory (SSCL) was developed for a number of reasons. The need for a quality program not only is a contractual requirement, but it also makes good economic sense to implement such a program. The quality program is the device used to coordinate the activities of different Laboratory organizations, such as Engineering and Procurement, and to improve operational reliability and safety. To be successful, the QA Program not only must satisfy Department of Energy (DOE) requirements and provide for flowdown of requirements to performing organizations, but must also be flexible enough so that the program is tailored to meet the needs of each internal organization. The keys to success are management support, acceptance by personnel, and cost effectiveness. These three items are assured by involving appropriate management at each step of program development, by personnel training and by feedback, and by programs to reduce defects and improve quality. Equally valuable is involvement of key organizations in program development. We will describe the basic SSCL Quality Program requirements, how the requirements are tailored to the needs of Laboratory organizations, and how the effectiveness of the program is validated

  14. Foreign criteria and programs

    International Nuclear Information System (INIS)

    Swinth, K.L.; Thompson, I.M.G.

    1993-03-01

    The concept of measurement quality assurance (MQA) as embodied in National Institute of Standards and Technology (NIST) programs is not generally used within European programs for testing or accreditation. Although the essential elements of quality control and quality assurance are in the European programs, the concept of testing the capability of the laboratory itself, in terms of its performance for the designated measurements, may not be included. Rather, the European programs use the concept of periodic calibration of laboratory reference standards against the next highest level of standards. Thus, they embody the concept of measurement traceability to appropriate primary standards. Within Europe a series of calibration accreditation programs has been established in the various countries tied together through a multilateral agreement. The radiation measurement programs are based on the International Organization for Standardization (ISO) 9000 series of standards. The purpose of this paper is to outline the overall operation of European Accreditation Programs in the radiation calibration and measurement areas. The operation of the radiation measurement programs of the National Measurement Accreditation Service (NAMAS) in the United Kingdom is described in detail along with other European programs. The manner in which these programs relate to individual dosimetry service programs is also described

  15. Functional Programming in R

    DEFF Research Database (Denmark)

    Mailund, Thomas

    Master functions and discover how to write functional programs in R. In this book, you'll make your functions pure by avoiding side-effects; you’ll write functions that manipulate other functions, and you’ll construct complex functions using simpler functions as building blocks. In Functional...... Programming in R, you’ll see how we can replace loops, which can have side-effects, with recursive functions that can more easily avoid them. In addition, the book covers why you shouldn't use recursion when loops are more efficient and how you can get the best of both worlds. Functional programming...... is a style of programming, like object-oriented programming, but one that focuses on data transformations and calculations rather than objects and state. Where in object-oriented programming you model your programs by describing which states an object can be in and how methods will reveal or modify...

  16. Functional Programming in R

    DEFF Research Database (Denmark)

    Mailund, Thomas

    2017-01-01

    Master functions and discover how to write functional programs in R. In this book, you'll make your functions pure by avoiding side-effects; you’ll write functions that manipulate other functions, and you’ll construct complex functions using simpler functions as building blocks. In Functional...... Programming in R, you’ll see how we can replace loops, which can have side-effects, with recursive functions that can more easily avoid them. In addition, the book covers why you shouldn't use recursion when loops are more efficient and how you can get the best of both worlds. Functional programming...... is a style of programming, like object-oriented programming, but one that focuses on data transformations and calculations rather than objects and state. Where in object-oriented programming you model your programs by describing which states an object can be in and how methods will reveal or modify...

  17. CROSSER - CUMULATIVE BINOMIAL PROGRAMS

    Science.gov (United States)

    Bowerman, P. N.

    1994-01-01

    The cumulative binomial program, CROSSER, is one of a set of three programs which calculate cumulative binomial probability distributions for arbitrary inputs. The three programs, CROSSER, CUMBIN (NPO-17555), and NEWTONP (NPO-17556), can be used independently of one another. CROSSER can be used by statisticians and users of statistical procedures, test planners, designers, and numerical analysts. The program has been used for reliability/availability calculations. CROSSER calculates the point at which the reliability of a k-out-of-n system equals the common reliability of the n components. It is designed to work well with all integer values 0 < k <= n. To run the program, the user simply runs the executable version and inputs the information requested by the program. The program is not designed to weed out incorrect inputs, so the user must take care to make sure the inputs are correct. Once all input has been entered, the program calculates and lists the result. It also lists the number of iterations of Newton's method required to calculate the answer within the given error. The CROSSER program is written in C. It was developed on an IBM AT with a numeric co-processor using Microsoft C 5.0. Because the source code is written using standard C structures and functions, it should compile correctly with most C compilers. The program format is interactive. It has been implemented under DOS 3.2 and has a memory requirement of 26K. CROSSER was developed in 1988.

  18. Generating Consistent Program Tutorials

    DEFF Research Database (Denmark)

    Vestdam, Thomas

    2002-01-01

    In this paper we present a tool that supports construction of program tutorials. A program tutorial provides the reader with an understanding of an example program by interleaving fragments of source code and explaining text. An example program can for example illustrate how to use a library or a......, and we see potential in using the tool to produce program tutorials to be used for frameworks, libraries, and in educational contexts.......In this paper we present a tool that supports construction of program tutorials. A program tutorial provides the reader with an understanding of an example program by interleaving fragments of source code and explaining text. An example program can for example illustrate how to use a library...... or a framework. We present a means for specifying the fragments of a program that are to be in-lined in the tutorial text. These in-line fragments are defined by addressing named syntactical elements, such as classes and methods, but it is also possible to address individual code lines by labeling them...

  19. Program management system manual

    International Nuclear Information System (INIS)

    1989-08-01

    OCRWM has developed a program management system (PMS) to assist in organizing, planning, directing and controlling the Civilian Radioactive Waste Management Program. A well defined management system is necessary because: (1) the Program is a complex technical undertaking with a large number of participants, (2) the disposal and storage facilities to be developed by the Program must be licensed by the Nuclear Regulatory Commission (NRC) and hence are subject to rigorous quality assurance (QA) requirements, (3) the legislation mandating the Program creates a dichotomy between demanding schedules of performance and a requirement for close and continuous consultation and cooperation with external entities, (4) the various elements of the Program must be managed as parts of an integrated waste management system, (5) the Program has an estimated total system life cycle cost of over $30 billion, and (6) the Program has a unique fiduciary responsibility to the owners and generators of the nuclear waste for controlling costs and minimizing the user fees paid into the Nuclear Waste Fund. This PMS Manual is designed and structured to facilitate strong, effective Program management by providing policies and requirements for organizing, planning, directing and controlling the major Program functions

  20. Site Support Program Plan Infrastructure Program

    International Nuclear Information System (INIS)

    1995-01-01

    The Fiscal Year 1996 Infrastructure Program Site Support Program Plan addresses the mission objectives, workscope, work breakdown structures (WBS), management approach, and resource requirements for the Infrastructure Program. Attached to the plan are appendices that provide more detailed information associated with scope definition. The Hanford Site's infrastructure has served the Site for nearly 50 years during defense materials production. Now with the challenges of the new environmental cleanup mission, Hanford's infrastructure must meet current and future mission needs in a constrained budget environment, while complying with more stringent environmental, safety, and health regulations. The infrastructure requires upgrading, streamlining, and enhancement in order to successfully support the site mission of cleaning up the Site, research and development, and economic transition

  1. Site Support Program Plan Infrastructure Program

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-26

    The Fiscal Year 1996 Infrastructure Program Site Support Program Plan addresses the mission objectives, workscope, work breakdown structures (WBS), management approach, and resource requirements for the Infrastructure Program. Attached to the plan are appendices that provide more detailed information associated with scope definition. The Hanford Site`s infrastructure has served the Site for nearly 50 years during defense materials production. Now with the challenges of the new environmental cleanup mission, Hanford`s infrastructure must meet current and future mission needs in a constrained budget environment, while complying with more stringent environmental, safety, and health regulations. The infrastructure requires upgrading, streamlining, and enhancement in order to successfully support the site mission of cleaning up the Site, research and development, and economic transition.

  2. Programming Scala Scalability = Functional Programming + Objects

    CERN Document Server

    Wampler, Dean

    2009-01-01

    Learn how to be more productive with Scala, a new multi-paradigm language for the Java Virtual Machine (JVM) that integrates features of both object-oriented and functional programming. With this book, you'll discover why Scala is ideal for highly scalable, component-based applications that support concurrency and distribution. Programming Scala clearly explains the advantages of Scala as a JVM language. You'll learn how to leverage the wealth of Java class libraries to meet the practical needs of enterprise and Internet projects more easily. Packed with code examples, this book provides us

  3. Evaluation Program initiative

    International Nuclear Information System (INIS)

    Rich, B.L.

    1987-01-01

    The purpose of this paper is to provide the Department of Energy's (DOE) safeguards and security community with some insights on an important management initiative by the Office of Security Evaluations (OSE). The paper will present the ''what, where, who, when, and why'' of a new Evaluation Program. The Evaluation Program will be comprised of a continuing series of regular and special evaluations of DOE safeguards and security programs and policies. The evaluations will be integrative and ''crosscutting,'' i.e. will extend across DOE organizational lines. Evaluations will be offered as positive advisories to DOE managers with safeguards and security responsibilities and will not be rated. They will complement the ongoing OSE Inspection Program of inspections conducted by OSE's Inspection Division. The purpose for the evaluations is to establish an accurate and current assessment of the effectiveness and status of safeguards and security programs and policies and to provide DOE managers with required information on program and policy effectiveness

  4. MIDI Programming in Scheme

    DEFF Research Database (Denmark)

    Nørmark, Kurt

    2010-01-01

    makes it possible to carry out systematic modifications and transformations of MIDI contents with use of pure functional programming. Side by side with the XML-inspired MIDI language, the paper describes an Emacs-based, textual programming environment that supports the MIDI programming process....... The programming environment also supports a variety of interactive features - similar to MIDI sequencers - but restricted to a textual representation of the music. The main contributions of the work are considered to be (1) An accumulated MIDI function library, which can transform MIDI files in many non......-trivial ways; (2) A proposed working process alternating between creative mode and programmatic editing mode within a MIDI programming environment; and (3) A textual MIDI programming environment with embedded support of many interactive, MIDI-related functionalities....

  5. Programming in biomolecular computation

    DEFF Research Database (Denmark)

    Hartmann, Lars Røeboe; Jones, Neil; Simonsen, Jakob Grue

    2011-01-01

    Our goal is to provide a top-down approach to biomolecular computation. In spite of widespread discussion about connections between biology and computation, one question seems notable by its absence: Where are the programs? We identify a number of common features in programming that seem...... conspicuously absent from the literature on biomolecular computing; to partially redress this absence, we introduce a model of computation that is evidently programmable, by programs reminiscent of low-level computer machine code; and at the same time biologically plausible: its functioning is defined...... by a single and relatively small set of chemical-like reaction rules. Further properties: the model is stored-program: programs are the same as data, so programs are not only executable, but are also compilable and interpretable. It is universal: all computable functions can be computed (in natural ways...

  6. Toy Control Program evaluation.

    Science.gov (United States)

    Stewart, H A; Ormond, C; Seeger, B R

    1991-08-01

    The Toy Control Program for the Apple IIe microcomputer is a software and hardware package developed for the training of single-switch scanning skills. The specially designed scanning programs provide on screen visual feedback and activate a battery-powered toy to reinforce performance. This study examined whether the training of preschool subjects in single-switch scanning skills with the Toy Control Program would result in increased task completion scores and increased levels of attention to task, as compared with conditions of toy activation only and microcomputer programs with screen reinforcement only. The results showed that the subjects paid significantly more attention to the toys as reinforcers (p less than .01). No significant difference was found for the performance results of the three conditions. These findings support the use of a program like the Toy Control Program, which integrates the instructional capabilities of a computer with the reinforcement potential of a toy and the creativity of a therapist.

  7. Meteorological Monitoring Program

    International Nuclear Information System (INIS)

    Hancock, H.A. Jr.; Parker, M.J.; Addis, R.P.

    1994-01-01

    The purpose of this technical report is to provide a comprehensive, detailed overview of the meteorological monitoring program at the Savannah River Site (SRS) near Aiken, South Carolina. The principle function of the program is to provide current, accurate meteorological data as input for calculating the transport and diffusion of any unplanned release of an atmospheric pollutant. The report is recommended for meteorologists, technicians, or any personnel who require an in-depth understanding of the meteorological monitoring program

  8. Probabilistic Programming (Invited Talk)

    OpenAIRE

    Yang, Hongseok

    2017-01-01

    Probabilistic programming refers to the idea of using standard programming constructs for specifying probabilistic models from machine learning and statistics, and employing generic inference algorithms for answering various queries on these models, such as posterior inference and estimation of model evidence. Although this idea itself is not new and was, in fact, explored by several programming-language and statistics researchers in the early 2000, it is only in the last few years that proba...

  9. Robust Programming by Example

    OpenAIRE

    Bishop , Matt; Elliott , Chip

    2011-01-01

    Part 2: WISE 7; International audience; Robust programming lies at the heart of the type of coding called “secure programming”. Yet it is rarely taught in academia. More commonly, the focus is on how to avoid creating well-known vulnerabilities. While important, that misses the point: a well-structured, robust program should anticipate where problems might arise and compensate for them. This paper discusses one view of robust programming and gives an example of how it may be taught.

  10. Intelligence of programs

    Energy Technology Data Exchange (ETDEWEB)

    Novak, D

    1982-01-01

    A general discussion about the level of artificial intelligence in computer programs is presented. The suitability of various languages for the development of complex, intelligent programs is discussed, considering fourth-generation language as well as the well established structured COBOL language. It is concluded that the success of automation in many administrative fields depends to a large extent on the development of intelligent programs.

  11. Los Alamos Programming Models

    Energy Technology Data Exchange (ETDEWEB)

    Bergen, Benjamin Karl [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-07-07

    This is the PDF of a powerpoint presentation from a teleconference on Los Alamos programming models. It starts by listing their assumptions for the programming models and then details a hierarchical programming model at the System Level and Node Level. Then it details how to map this to their internal nomenclature. Finally, a list is given of what they are currently doing in this regard.

  12. Are Stabilization Programs Expansionary?

    OpenAIRE

    Federico Echenique; Alvaro Forteza

    1997-01-01

    The empirical evidence presented in this paper casts serious doubts on the by now widely accepted "stylized facts" of the exchange rate based stabilization programs (ERBS) as they are stated in Kiguel and Liviatan (1992) and in Végh (1992). Even though the ERBS programs were associated with output booms, no evidence of booms provoked by the stabilization programs is found. Rather, exogenous capital inflows to Latin America seem to have caused both the output booms and the stabilization progra...

  13. Meteorological Monitoring Program

    Energy Technology Data Exchange (ETDEWEB)

    Hancock, H.A. Jr. [ed.; Parker, M.J.; Addis, R.P.

    1994-09-01

    The purpose of this technical report is to provide a comprehensive, detailed overview of the meteorological monitoring program at the Savannah River Site (SRS) near Aiken, South Carolina. The principle function of the program is to provide current, accurate meteorological data as input for calculating the transport and diffusion of any unplanned release of an atmospheric pollutant. The report is recommended for meteorologists, technicians, or any personnel who require an in-depth understanding of the meteorological monitoring program.

  14. Tribal Waste Management Program

    Science.gov (United States)

    The EPA’s Tribal Waste Management Program encourages environmentally sound waste management practices that promote resource conservation through recycling, recovery, reduction, clean up, and elimination of waste.

  15. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Special Activities Resources Housing and Travel ... Contact Online Education Accreditation, Verification, and Validation Accreditation, Verification, and Validation Programs Accreditation, Verification, and ...

  16. Introduction to dynamic programming

    CERN Document Server

    Cooper, Leon; Rodin, E Y

    1981-01-01

    Introduction to Dynamic Programming provides information pertinent to the fundamental aspects of dynamic programming. This book considers problems that can be quantitatively formulated and deals with mathematical models of situations or phenomena that exists in the real world.Organized into 10 chapters, this book begins with an overview of the fundamental components of any mathematical optimization model. This text then presents the details of the application of dynamic programming to variational problems. Other chapters consider the application of dynamic programming to inventory theory, Mark

  17. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Advocate at Home Program State Legislative Action Center Leadership & Advocacy Summit Webinars Practice Management Practice Management Practice Management CPT Coding Bulletin Articles ...

  18. Local Estuary Programs

    Science.gov (United States)

    This page provides information about Local Individual Estuary Programs including links to their NEP homepages, social media, Comprehensive Conservation and Management Plans, and state of the bay reports.

  19. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Life Support Verification, Review, and Consultation Program for Hospitals ... Injury Prevention and Control Quality and Safety Conference Quality and Safety Conference Quality ...

  20. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Health Records (EHR) Incentive Program Physician Quality Reporting System Value-Based Payment ... Practice Management Practice Management Practice Management CPT Coding Bulletin Articles ...

  1. Knowledge management program

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, T. [CANDU Owners' Group, Toronto, Ontario (Canada)

    2013-07-01

    To capture and retain the CANDU experience from a wider CANDU base and transfer knowledge and experience to our members, supplier participants and universities in a cost effective manner. Major focus area of the program is knowledge management joint projects, generic training delivery, inter-utilities mentoring and technical support, public education programs. The path forward is execution of transition of OPG NPDS Program as an ongoing program in COG with member funding, pursue opportunities to provide member utilities with additional leadership and train-the-trainer training and grow the knowledge management activities by 20% per year based on 2013/2014 results.

  2. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Online Guide to Choosing a Surgical Residency Practice Management Workshops Patients and Family Patient Education Patient Education Patients Medical Professionals Skills Programs Find ...

  3. Transit Benefit Program Data -

    Data.gov (United States)

    Department of Transportation — This data set contains information about any US government agency participating in the transit benefits program, funding agreements, individual participating Federal...

  4. Knowledge management program

    International Nuclear Information System (INIS)

    Henderson, T.

    2013-01-01

    To capture and retain the CANDU experience from a wider CANDU base and transfer knowledge and experience to our members, supplier participants and universities in a cost effective manner. Major focus area of the program is knowledge management joint projects, generic training delivery, inter-utilities mentoring and technical support, public education programs. The path forward is execution of transition of OPG NPDS Program as an ongoing program in COG with member funding, pursue opportunities to provide member utilities with additional leadership and train-the-trainer training and grow the knowledge management activities by 20% per year based on 2013/2014 results.

  5. Programming Language Pragmatics

    CERN Document Server

    Scott, Michael L

    2009-01-01

    Programming Language Pragmatics is the most comprehensive programming language textbook available today. Taking the perspective that language design and language implementation are tightly interconnected, and that neither can be fully understood in isolation, this critically acclaimed and bestselling book has been thoroughly updated to cover the most recent developments in programming language design. With a new chapter on run-time program management and expanded coverage of concurrency, this new edition provides both students and professionals alike with a solid understanding of the most impo

  6. Virginia Natural Heritage Program

    Science.gov (United States)

    Heritage About Natural Heritage Overview, Mission Natural Heritage Inventory Community Ecology Program ) | Strategic Plan (PDF) | Executive Progress Report (PDF) | Code of Ethics (PDF) Your browser does not support

  7. Practical C programming

    CERN Document Server

    Oualline, Steve

    1997-01-01

    There are lots of introductory C books, but this is the first one that has the no-nonsense, practical approach that has made Nutshell Handbooks® famous. C programming is more than just getting the syntax right. Style and debugging also play a tremendous part in creating programs that run well and are easy to maintain. This book teaches you not only the mechanics of programming, but also describes how to create programs that are easy to read, debug, and update. Practical rules are stressed. For example, there are fifteen precedence rules in C (&& comes before || comes before ?:). The practi

  8. Ostomy Home Skills Program

    Medline Plus

    Full Text Available ... Program Federal Legislation Federal Legislation Federal Legislation Health Care Reform Summary Letters on Health Care Reform Medicare Physician Payment Medical Liability Reform Opioids ...

  9. Construction program management

    CERN Document Server

    Delaney, Joseph

    2013-01-01

    Although construction is one of the largest industries in the United States, it lags behind other industries in its implementation of modern management techniques such as those contained in the Standard for Program Management (the Standard) by the Project Management Institute (PMI(R)). Construction Program Management details the successful use of the PMI(R) approach for the construction of capital programs. It demonstrates, through case studies, how implementation of PMI's set of tools and techniques can improve the chances of program success. Exploring tactical and strategic management method

  10. Veterinary Services Program

    Data.gov (United States)

    Federal Laboratory Consortium — Mission:To provide quality veterinary medical care and environmental enrichment programs for all animals, representing nine different species.To provide guidance for...

  11. Energy research program 80

    International Nuclear Information System (INIS)

    1980-01-01

    The energy research program 80 contains an extension of the activities for the period 1980-82 within a budget of 100 mio.kr., that are a part of the goverment's employment plan for 1980. The research program is based on a number of project proposals, that have been collected, analysed, and supplemented in October-November 1979. This report consists of two parts. Part 1: a survey of the program, with a brief description of the background, principles, organization and financing. Part 2: Detailed description of the different research programs. (LN)

  12. Advanced Industrial Materials Program

    Science.gov (United States)

    Stooksbury, F.

    1994-06-01

    The mission of the Advanced Industrial Materials (AIM) program is to commercialize new/improved materials and materials processing methods that will improve energy efficiency, productivity, and competitiveness. Program investigators in the DOE national laboratories are working with about 100 companies, including 15 partners in CRDA's. Work is being done on intermetallic alloys, ceramic composites, metal composites, polymers, engineered porous materials, and surface modification. The program supports other efforts in the Office of Industrial Technologies to assist the energy-consuming process industries. The aim of the AIM program is to bring materials from basic research to industrial application to strengthen the competitive position of US industry and save energy.

  13. Privacy Training Program

    Science.gov (United States)

    Recognizing that training and awareness are critical to protecting agency Personally Identifiable Information (PII), the EPA is developing online training for privacy contacts in its programs and regions.

  14. Mini Project Programming Exams

    DEFF Research Database (Denmark)

    Nørmark, Kurt; Thomsen, Lone Leth; Torp, Kristian

    2008-01-01

    A number of different types of final programming exams used or considered at the Department of Computer Science, Aalborg University, are identified and analyzed. Based on this analysis, a new type of programming exam is introduced called a Mini Project Programming (MIP) exam. MIP is a group...... years. The MIP exam is a compromise between (1) a long problem-based project exam and (2) a short oral or written programming exam. It is concluded that the strengths of MIP are the high degree of realism in the exam assignment and comprehensiveness relative to the course syllabus. The main challenge...

  15. Programming language structures

    CERN Document Server

    Organick, Elliott Irving; Plummer, Robert P

    1978-01-01

    Programming Language Structures deals with the structures of programming languages and introduces the reader to five important programming languages: Algol, Fortran, Lisp, Snobol, and Pascal. The fundamental similarities and differences among these languages are discussed. A unifying framework is constructed that can be used to study the structure of other languages, such as Cobol, PL/I, and APL. Several of the tools and methodologies needed to construct large programs are also considered.Comprised of 10 chapters, this book begins with a summary of the relevant concepts and principles about al

  16. The standard for program management

    CERN Document Server

    2017-01-01

    The Standard for Program Management – Fourth Edition differs from prior editions by focusing on the principles of good program management. Program activities have been realigned to program lifecycle phases rather than topics, and the first section was expanded to address the key roles of program manager, program sponsor and program management office. It has also been updated to better align with PMI’s Governance of Portfolios, Programs, and Projects: A Practice Guide.

  17. Program Performance Inventory: Six Juvenile Offender Programs.

    Science.gov (United States)

    Thomalla, Terri Groff; Dougherty, Victoria J.

    This report describes the performance of 6 Connecticut juvenile justice alternative sanction programs in 14 qualitative areas: community reintegration; outcomes and evaluation; assessment methods; risk factors; escalation of criminal activity; family involvement; community involvement; work ethic and vocational training; education and life skills;…

  18. Transgenerational developmental programming.

    Science.gov (United States)

    Aiken, Catherine E; Ozanne, Susan E

    2014-01-01

    The concept of developmental programming suggests that the early life environment influences offspring characteristics in later life, including the propensity to develop diseases such as the metabolic syndrome. There is now growing evidence that the effects of developmental programming may also manifest in further generations without further suboptimal exposure. This review considers the evidence, primarily from rodent models, for effects persisting to subsequent generations, and evaluates the mechanisms by which developmental programming may be transmitted to further generations. In particular, we focus on the potential role of the intrauterine environment in contributing to a developmentally programmed phenotype in subsequent generations. The literature was systematically searched at http://pubmed.org and http://scholar.google.com to identify published findings regarding transgenerational (F2 and beyond) developmental programming effects in human populations and animal models. Transmission of programming effects is often viewed as a form of epigenetic inheritance, either via the maternal or paternal line. Evidence exists for both germline and somatic inheritance of epigenetic modifications which may be responsible for phenotypic changes in further generations. However, there is increasing evidence for the role of both extra-genomic components of the zygote and the interaction of the developing conceptus with the intrauterine environment in propagating programming effects. The contribution of a suboptimal reproductive tract environment or maternal adaptations to pregnancy may be critical to inheritance of programming effects via the maternal line. As the effects of age exacerbate the programmed metabolic phenotype, advancing maternal age may increase the likelihood of developmental programming effects being transmitted to further generations. We suggest that developmental programming effects could be propagated through the maternal line de novo in generations

  19. Program Management System manual

    International Nuclear Information System (INIS)

    1986-01-01

    The Program Management System (PMS), as detailed in this manual, consists of all the plans, policies, procedure, systems, and processes that, taken together, serve as a mechanism for managing the various subprograms and program elements in a cohesive, cost-effective manner. The PMS is consistent with the requirements of the Nuclear Waste Policy Act of 1982 and the ''Mission Plan for the Civilian Radioactive Waste Management Program'' (DOE/RW-0005). It is based on, but goes beyond, the Department of Energy (DOE) management policies and procedures applicable to all DOE programs by adapting these directives to the specific needs of the Civilian Radioactive Waste Management program. This PMS Manual describes the hierarchy of plans required to develop and maintain the cost, schedule, and technical baselines at the various organizational levels of the Civilian Radioactive Waste Management Program. It also establishes the management policies and procedures used in the implementation of the Program. These include requirements for internal reports, data, and other information; systems engineering management; regulatory compliance; safety; quality assurance; and institutional affairs. Although expanded versions of many of these plans, policies, and procedures are found in separate documents, they are an integral part of this manual. The PMS provides the basis for the effective management that is needed to ensure that the Civilian Radioactive Waste Management Program fulfills the mandate of the Nuclear Waste Policy Act of 1982. 5 figs., 2 tabs

  20. Human Performance Westinghouse Program

    International Nuclear Information System (INIS)

    Garcia Gutierrez, A.; Gil, C.

    2010-01-01

    The objective of the Program consists in the excellence actuation, achieving the client success with a perfect realisation project. This program consists of different basic elements to reduce the human mistakes: the HuP tools, coaching, learning clocks and iKnow website. There is, too, a document file to consult and practice. All these elements are expounded in this paper.

  1. The Weekend Intervention Program.

    Science.gov (United States)

    Siegal, Harvey A.

    The Weekend Intervention Program (WIP) at the Wright State University School of Medicine is described in this report. Designed to address severe health and social problems while supporting the university's academic mission, the program began with the goal of addressing the health and social problems of alcohol abusers. WIP is a 72-hour intensive…

  2. Process control program development

    International Nuclear Information System (INIS)

    Dameron, H.J.

    1985-01-01

    This paper details the development and implementation of a ''Process Control Program'' at Duke Power's three nuclear stations - Oconee, McGuire, and Catawba. Each station is required by Technical Specification to have a ''Process Control Program'' (PCP) to control all dewatering and/or solidification activities for radioactive wastes

  3. Home | SREL Herpetology Program

    Science.gov (United States)

    Savannah River Ecology Laboratory Herpetology Program Herp Home Research Publications Herps of SC /GA P.A.R.C. Outreach SREL Home powered by Google Search Herpetology at SREL The University of SREL herpetology research programs have always included faculty of the University of Georgia, post

  4. Programmed cell death

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    The purpose of this conference to provide a multidisciplinary forum for exchange of state-of-the-art information on the role programmed cell death plays in normal development and homeostasis of many organisms. This volume contains abstracts of papers in the following areas: invertebrate development; immunology/neurology; bcl-2 family; biochemistry; programmed cell death in viruses; oncogenesis; vertebrate development; and diseases.

  5. DOE's Phytoremediation Program

    International Nuclear Information System (INIS)

    Levine, R.S.

    1996-01-01

    This presentation contains an outline of the US DOE's phytoremediation program. A brief overview of the goals, infrastructure, and results of the program is presented. Environmental contaminants addressed include chlorinated hydrocarbons, metals, radionuclides, inorganic wastes, and mixed hazardous and radioactive wastes. Studies of soil remediation using phytoextraction and water remediation using rhizofiltration are briefly described

  6. Financing Competency Based Programs.

    Science.gov (United States)

    Daniel, Annette

    Literature on the background, causes, and current prevalence of competency based programs is synthesized in this report. According to one analysis of the actual and probable costs of minimum competency testing, estimated costs for test development, test administration, bureaucratic structures, and remedial programs for students who cannot pass the…

  7. Programming Language Paradigms

    Directory of Open Access Journals (Sweden)

    Bartoníček Jan

    2014-01-01

    Full Text Available This paper's goal is to briefly explain the basic theory behind programming languages and their history while taking a close look at different programming paradigms that are used today as well as describing their differences, benefits, and drawbacks

  8. NVLAP calibration laboratory program

    Energy Technology Data Exchange (ETDEWEB)

    Cigler, J.L.

    1993-12-31

    This paper presents an overview of the progress up to April 1993 in the development of the Calibration Laboratories Accreditation Program within the framework of the National Voluntary Laboratory Accreditation Program (NVLAP) at the National Institute of Standards and Technology (NIST).

  9. Marketing University Outreach Programs.

    Science.gov (United States)

    Foster, Ralph S., Jr., Ed.; And Others

    A collection of 12 essays and model program descriptions addresses issues in the marketing of university extension, outreach, and distance education programs. They include: (1) "Marketing and University Outreach: Parallel Processes" (William I. Sauser, Jr. and others); (2) "Segmenting and Targeting the Organizational Market"…

  10. Programs and Expertise

    CERN Document Server

    2001-01-01

    Description of programs and expertise implemented by Radiation Protection Centre is presented. RPC implements study assessing the doses received by air crew members of Lithuanian Airlines. In 2001 RPC started measurements of indoor radon concentrations in the houses of regions with karst formations, commenced new program analyzing amounts of radionuclides in typical diet of hospital patients.

  11. Multiprocessor programming environment

    Energy Technology Data Exchange (ETDEWEB)

    Smith, M.B.; Fornaro, R.

    1988-12-01

    Programming tools and techniques have been well developed for traditional uniprocessor computer systems. The focus of this research project is on the development of a programming environment for a high speed real time heterogeneous multiprocessor system, with special emphasis on languages and compilers. The new tools and techniques will allow a smooth transition for programmers with experience only on single processor systems.

  12. Learning Apex programming

    CERN Document Server

    Kaufman, Matt

    2015-01-01

    If you are a developer who has some object-oriented programming experience, Learning Apex Programming is the perfect book for you. This book is most appropriate for developers who wish to gain an understanding of the Force.com platform and how to use Apex to create business applications.

  13. INEL BNCT Program

    International Nuclear Information System (INIS)

    Ackermann, A.L.; Dorn, R.V. III.

    1991-03-01

    This Bulletin presents a summary of accomplishments and highlights in the Idaho National Engineering Laboratory (INEL) Boron Neutron Capture Therapy (BNCT) Program for March 1991. This bulletin includes information on the brain tumor and melanoma research programs, Power Burst Facility (PBF) technical support and modifications, PBF operations, a milestone summary, and animal data charts

  14. Programming Languages RESONAN

    Indian Academy of Sciences (India)

    Introduction. Programming languages for computers are developed with the ... detailed algorithm to solve a problem is the starting point and it is expressed as ... All modern programming .... which precisely specify the 'words' of the language, and how they may .... network within an organization using protocols and providing.

  15. Air Pollution Training Programs.

    Science.gov (United States)

    Public Health Service (DHEW), Rockville, MD.

    This catalog lists the universities, both supported and not supported by the Division of Air Pollution, which offer graduate programs in the field of air pollution. The catalog briefly describes the programs and their entrance requirements, the requirements, qualifications and terms of special fellowships offered by the Division of Air Pollution.…

  16. Programs and datatypes

    NARCIS (Netherlands)

    Doornbos, H.; Gasteren, van A.J.M.; Backhouse, R.C.; Brink, C.H.; Kahl, W.; Schmidt, G.

    1997-01-01

    We are programmers, in the sense that it is our concern to improve the process of program construction. Therefore we want to answer questions like: What is programming, why is it so difficult and error-prone, and how can we learn what is needed to make the process more manageable? In the following

  17. Human Sexuality Education Program.

    Science.gov (United States)

    Claremont Univ. Center, CA.

    This program provides information to students about human sexual biology, behavior and attitudes. The primary intent of the workshops described is to provide fuller information and opportunity for self awareness to encourage participants to be more responsible as sexual beings, and to restructure their attitudes. The program presents the…

  18. Linear genetic programming

    CERN Document Server

    Brameier, Markus

    2007-01-01

    Presents a variant of Genetic Programming that evolves imperative computer programs as linear sequences of instructions, in contrast to the more traditional functional expressions or syntax trees. This book serves as a reference for researchers, but also contains sufficient introduction for students and those who are new to the field

  19. Search and imperative programming

    NARCIS (Netherlands)

    K.R. Apt (Krzysztof); A. Schaerf

    1996-01-01

    textabstractWe augment the expressive power of imperative programming in order to make it a more attractive vehicle for problems that involve search.The proposed additions are limited yet powerful and are inspired by the logic programming paradigm.We illustrate their use by presenting solutions to a

  20. Generation IV national program

    International Nuclear Information System (INIS)

    Preville, M.; Sadhankar, R.; Brady, D.

    2007-01-01

    This paper outlines the Generation IV National Program. This program involves evolutionary and innovative design with significantly higher efficiencies (∼50% compared to present ∼30%) - sustainable, economical, safe, reliable and proliferation resistant - for future energy security. The Generation IV Forum (GIF) effectively leverages the resources of the participants to meet these goals. Ten countries signed the GIF Charter in 2001

  1. The RERTR Program

    International Nuclear Information System (INIS)

    Travelli, A.

    1992-01-01

    The progress of the Reduced Enrichment Research and Test Reactor (RERTR) Program is described. The major events, findings, and activities of 1991 are reviewed after a brief summary of the results which the RERTR Program had achieved by the end of 1991 in collaboration with its many international partners

  2. Evaluating a Development Program.

    Science.gov (United States)

    Frantzreb, Arthur C.

    Problems in evaluating the success of an institutional resource development program are examined and suggestions are offered for effective assessment. Such a program is seen as a sequence of events in the artful management of people, from the planning stage to obtaining a financial commitment in writing from persons who want to share their assets…

  3. Modeling EERE Deployment Programs

    Energy Technology Data Exchange (ETDEWEB)

    Cort, K. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hostick, D. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Belzer, D. B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Livingston, O. V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2007-11-01

    This report compiles information and conclusions gathered as part of the “Modeling EERE Deployment Programs” project. The purpose of the project was to identify and characterize the modeling of deployment programs within the EERE Technology Development (TD) programs, address possible improvements to the modeling process, and note gaps in knowledge in which future research is needed.

  4. Optimal Quadratic Programming Algorithms

    CERN Document Server

    Dostal, Zdenek

    2009-01-01

    Quadratic programming (QP) is one technique that allows for the optimization of a quadratic function in several variables in the presence of linear constraints. This title presents various algorithms for solving large QP problems. It is suitable as an introductory text on quadratic programming for graduate students and researchers

  5. National School Lunch Program

    Science.gov (United States)

    US Department of Agriculture, 2009

    2009-01-01

    The National School Lunch Program is a federally assisted meal program operating in over 101,000 public and non-profit private schools and residential child care institutions. It provides nutritionally balanced, low-cost or free lunches to more than 30.5 million children each school day in 2008. In 1998, Congress expanded the National School Lunch…

  6. Linear Programming (LP)

    International Nuclear Information System (INIS)

    Rogner, H.H.

    1989-01-01

    The submitted sections on linear programming are extracted from 'Theorie und Technik der Planung' (1978) by W. Blaas and P. Henseler and reformulated for presentation at the Workshop. They consider a brief introduction to the theory of linear programming and to some essential aspects of the SIMPLEX solution algorithm for the purposes of economic planning processes. 1 fig

  7. NVLAP calibration laboratory program

    International Nuclear Information System (INIS)

    Cigler, J.L.

    1993-01-01

    This paper presents an overview of the progress up to April 1993 in the development of the Calibration Laboratories Accreditation Program within the framework of the National Voluntary Laboratory Accreditation Program (NVLAP) at the National Institute of Standards and Technology (NIST)

  8. Monadic Functional Reactive Programming

    NARCIS (Netherlands)

    A.J. van der Ploeg (Atze); C Shan

    2013-01-01

    htmlabstractFunctional Reactive Programming (FRP) is a way to program reactive systems in functional style, eliminating many of the problems that arise from imperative techniques. In this paper, we present an alternative FRP formulation that is based on the notion of a reactive computation: a

  9. The Greenfoot Programming Environment

    Science.gov (United States)

    Kolling, Michael

    2010-01-01

    Greenfoot is an educational integrated development environment aimed at learning and teaching programming. It is aimed at a target audience of students from about 14 years old upwards, and is also suitable for college- and university-level education. Greenfoot combines graphical, interactive output with programming in Java, a standard, text-based…

  10. The evolution of programs

    CERN Document Server

    Dershowitz, Nachum

    1983-01-01

    -Ecclesiastes 12:12 Programs are invariably subjected to many rorms or transrormation. After an initial version of a program has been designed and developed, it undergoes debugging and certification. In addition, most long-lived pro­ grams have a liCe-cycle that includes modifications to meet amended specifications and extensions for expanded capabilities. Such evolution­ ary aspects of programming are the topic of this monograph. We present rormal methods for manipulating programs and illustrate their applica­ tion with numerous examples. Such methods could be incorporated in semi-automated programming environments, where they would serve to ease the burden on the programmer. We begin by describing a method whereby a given program that achieves one goal can be modified to achieve a different goal or a pro­ gram that computes wrong results can be debugged to achieve the 2 Preface intended results. The abstraction of a set of cognate programs to obtain a program schema, and the instantiation of abstract sc...

  11. PIA Program | CTIO

    Science.gov (United States)

    , accept unpaid interns who have funding through another source. For example, in the past we have hosted at CTIO, or if you have any questions about past CTIO PIA Programs, please send email to ctiopia each year to participate in a research program funded by CTIO and carried out together with the REU

  12. Responsive Space Program Brief

    Energy Technology Data Exchange (ETDEWEB)

    Dors, Eric E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-03-11

    The goal of the Responsive Space program is to make significant, integrated science and technology contributions to the end-to-end missions of the U.S. Government that protect against global emerging and nuclear threats, from the earliest adversary planning through resilient event response report describes the LANL space program, mission, and other activities. The report describes some of their activities.

  13. Logic Programming: PROLOG.

    Science.gov (United States)

    Lopez, Antonio M., Jr.

    1989-01-01

    Provides background material on logic programing and presents PROLOG as a high-level artificial intelligence programing language that borrows its basic constructs from logic. Suggests the language is one which will help the educator to achieve various goals, particularly the promotion of problem solving ability. (MVL)

  14. Object oriented programming

    International Nuclear Information System (INIS)

    Kunz, P.F.

    1990-01-01

    This paper is an introduction to object oriented programming techniques. It tries to explain the concepts by using analogies with traditional programming. The object oriented approach not inherently difficult, but most programmers find a relatively high threshold in learning it. Thus, this paper will attempt to convey the concepts with examples rather than explain the formal theory

  15. INEL BNCT Program

    Energy Technology Data Exchange (ETDEWEB)

    Ackermann, A.L. (ed.)

    1991-08-01

    This Bulletin presents a summary of accomplishments and highlights in the Idaho National Engineering Laboratory's (INEL) Boron Neutron Capture Therapy (BNCT) Program for August 1991. This bulletin includes information on the brain tumor and melanoma research programs, Power Burst Facility (PBF) technical support and modifications, PBF operations, and updates to the animal data charts.

  16. Scientific Programming in Fortran

    Directory of Open Access Journals (Sweden)

    W. Van Snyder

    2007-01-01

    Full Text Available The Fortran programming language was designed by John Backus and his colleagues at IBM to reduce the cost of programming scientific applications. IBM delivered the first compiler for its model 704 in 1957. IBM's competitors soon offered incompatible versions. ANSI (ASA at the time developed a standard, largely based on IBM's Fortran IV in 1966. Revisions of the standard were produced in 1977, 1990, 1995 and 2003. Development of a revision, scheduled for 2008, is under way. Unlike most other programming languages, Fortran is periodically revised to keep pace with developments in language and processor design, while revisions largely preserve compatibility with previous versions. Throughout, the focus on scientific programming, and especially on efficient generated programs, has been maintained.

  17. Programming in biomolecular computation

    DEFF Research Database (Denmark)

    Hartmann, Lars Røeboe; Jones, Neil; Simonsen, Jakob Grue

    2010-01-01

    in a strong sense: a universal algorithm exists, that is able to execute any program, and is not asymptotically inefficient. A prototype model has been implemented (for now in silico on a conventional computer). This work opens new perspectives on just how computation may be specified at the biological level......., by programs reminiscent of low-level computer machine code; and at the same time biologically plausible: its functioning is defined by a single and relatively small set of chemical-like reaction rules. Further properties: the model is stored-program: programs are the same as data, so programs are not only...... executable, but are also compilable and interpretable. It is universal: all computable functions can be computed (in natural ways and without arcane encodings of data and algorithm); it is also uniform: new “hardware” is not needed to solve new problems; and (last but not least) it is Turing complete...

  18. Electron trajectory program

    International Nuclear Information System (INIS)

    Herrmannsfeldt, W.B.

    1979-11-01

    The SLAC Electron Trajectory Program is described and instructions and examples for users are given. The program is specifically written to compute trajectories of charged particles in electrostatic and magnetostatic focusing systems including the effects of space charge and self-magnetic fields. Starting options include Child's Law conditions on cathodes of various shapes. Either rectangular or cylindrically symmetric geometry may be used. Magntic fields may be specified using arbitrary configurations of coils, or the output of a magnet program such as Poisson or by an externally calculated array of the axial fields. The program is available in IBM FORTRAN but can be easily converted for use on other brands of hardware. The program is intended to be used with a plotter whose interface the user must provide

  19. Functional Programming Using F#

    DEFF Research Database (Denmark)

    Hansen, Michael Reichhardt; Rischel, Hans

    This comprehensive introduction to the principles of functional programming using F# shows how to apply basic theoretical concepts to produce succinct and elegant programs. It demonstrates the role of functional programming in a wide spectrum of applications including databases and systems....... Coverage also includes advanced features in the .NET library, the imperative features of F# and topics such as text processing, sequences, computation expressions and asynchronous computation. With a broad spectrum of examples and exercises, the book is perfect for courses in functional programming...... and for self-study. Enhancing its use as a text is an accompanying website with downloadable programs, lecture slides, a mini-projects and links to further F# sources....

  20. The Siemens graduate program

    International Nuclear Information System (INIS)

    Schaeffler, I.

    2000-01-01

    Siemens is an international company acting in different domains: power generation, communication and information, traffic, health, etc. To be more flexible and active in a world in constant evolution, the company proposes a graduate program where young people with a special background have the possibility to start an international career in all the domains of activity. This graduate program is especially important in the domain of nuclear energy, where the know-how transfer between the previous generation and the new one is a constant point of interest. This article presents the conditions to be accepted in this graduate program, and the supplementary training supporting this program. The Siemens graduate program (Sg) proposes a global concept with a main emphasis being international. (authors)

  1. Hemovigilance Program-India

    Directory of Open Access Journals (Sweden)

    Akanksha Bisht

    2013-01-01

    Full Text Available A centralized hemovigilance program to assure patient safety and to promote public health has been launched for the first time in India on Dec 10, 2012 in 60 medical colleges in the first phase along with a well-structured program for monitoring adverse reactions associated with blood transfusion and blood product administration. National Institute of Biologicals (NIB will be the National Coordinating Centre for Hemovigilance. This program will be implemented under overall ambit of Pharmacovigilance Program of India (PvPI, which is being coordinated by Indian Pharmacopoeia Commission (IPC. All medical colleges of the country will be enrolled in this program by the year 2016 in order to have a National Centre of Excellence for Hemovigilance at NIB, which will act as a global knowledge platform.

  2. The Aircraft Morphing Program

    Science.gov (United States)

    Wlezien, R. W.; Horner, G. C.; McGowan, A. R.; Padula, S. L.; Scott, M. A.; Silcox, R. J.; Simpson, J. O.

    1998-01-01

    In the last decade smart technologies have become enablers that cut across traditional boundaries in materials science and engineering. Here we define smart to mean embedded actuation, sensing, and control logic in a tightly coupled feedback loop. While multiple successes have been achieved in the laboratory, we have yet to see the general applicability of smart devices to real aircraft systems. The NASA Aircraft Morphing program is an attempt to couple research across a wide range of disciplines to integrate smart technologies into high payoff aircraft applications. The program bridges research in seven individual disciplines and combines the effort into activities in three primary program thrusts. System studies are used to assess the highest- payoff program objectives, and specific research activities are defined to address the technologies required for development of smart aircraft systems. In this paper we address the overall program goals and programmatic structure, and discuss the challenges associated with bringing the technologies to fruition.

  3. Electron trajectory program

    Energy Technology Data Exchange (ETDEWEB)

    Herrmannsfeldt, W.B.

    1979-11-01

    The SLAC Electron Trajectory Program is described and instructions and examples for users are given. The program is specifically written to compute trajectories of charged particles in electrostatic and magnetostatic focusing systems including the effects of space charge and self-magnetic fields. Starting options include Child's Law conditions on cathodes of various shapes. Either rectangular or cylindrically symmetric geometry may be used. Magntic fields may be specified using arbitrary configurations of coils, or the output of a magnet program such as Poisson or by an externally calculated array of the axial fields. The program is available in IBM FORTRAN but can be easily converted for use on other brands of hardware. The program is intended to be used with a plotter whose interface the user must provide.

  4. Canadian fusion program

    International Nuclear Information System (INIS)

    Brown, T.S.

    1982-06-01

    The National Research Council of Canada is establishing a coordinated national program of fusion research and development that is planned to grow to a total annual operating level of about $20 million in 1985. The long-term objective of the program is to put Canadian industry in a position to manufacture sub-systems and components of fusion power reactors. In the near term the program is designed to establish a minimum base of scientific and technical expertise sufficient to make recognized contributions and thereby gain access to the international effort. The Canadian program must be narrowly focussed on a few specializations where Canada has special indigenous skills or technologies. The programs being funded are the Tokamak de Varennes, the Fusion Fuels Technology Project centered on tritium management, and high-power gas laser technology and associated diagnostic instrumentation

  5. Programs as Polypeptides.

    Science.gov (United States)

    Williams, Lance R

    2016-01-01

    Object-oriented combinator chemistry (OOCC) is an artificial chemistry with composition devices borrowed from object-oriented and functional programming languages. Actors in OOCC are embedded in space and subject to diffusion; since they are neither created nor destroyed, their mass is conserved. Actors use programs constructed from combinators to asynchronously update their own states and the states of other actors in their neighborhoods. The fact that programs and combinators are themselves reified as actors makes it possible to build programs that build programs from combinators of a few primitive types using asynchronous spatial processes that resemble chemistry as much as computation. To demonstrate this, OOCC is used to define a parallel, asynchronous, spatially distributed self-replicating system modeled in part on the living cell. Since interactions among its parts result in the construction of more of these same parts, the system is strongly constructive. The system's high normalized complexity is contrasted with that of a simple composome.

  6. CUMBIN - CUMULATIVE BINOMIAL PROGRAMS

    Science.gov (United States)

    Bowerman, P. N.

    1994-01-01

    The cumulative binomial program, CUMBIN, is one of a set of three programs which calculate cumulative binomial probability distributions for arbitrary inputs. The three programs, CUMBIN, NEWTONP (NPO-17556), and CROSSER (NPO-17557), can be used independently of one another. CUMBIN can be used by statisticians and users of statistical procedures, test planners, designers, and numerical analysts. The program has been used for reliability/availability calculations. CUMBIN calculates the probability that a system of n components has at least k operating if the probability that any one operating is p and the components are independent. Equivalently, this is the reliability of a k-out-of-n system having independent components with common reliability p. CUMBIN can evaluate the incomplete beta distribution for two positive integer arguments. CUMBIN can also evaluate the cumulative F distribution and the negative binomial distribution, and can determine the sample size in a test design. CUMBIN is designed to work well with all integer values 0 < k <= n. To run the program, the user simply runs the executable version and inputs the information requested by the program. The program is not designed to weed out incorrect inputs, so the user must take care to make sure the inputs are correct. Once all input has been entered, the program calculates and lists the result. The CUMBIN program is written in C. It was developed on an IBM AT with a numeric co-processor using Microsoft C 5.0. Because the source code is written using standard C structures and functions, it should compile correctly with most C compilers. The program format is interactive. It has been implemented under DOS 3.2 and has a memory requirement of 26K. CUMBIN was developed in 1988.

  7. Study design for a clinical trial to examine food price elasticity among participants in federal food assistance programs: A laboratory-based grocery store study

    Directory of Open Access Journals (Sweden)

    Zach Conrad

    2018-06-01

    Full Text Available We present a protocol for a study investigating the effect of food price changes on purchasing decisions among individuals participating in federal food assistance programs and among those not participating in these programs. We use a laboratory-based grocery store design, which provides greater control over factors influencing food purchasing than in situ experiments in actual grocery stores. We focus primarily, but not exclusively, on eggs because they are highly nutritious, easy to prepare, can be included in many different dishes, and are a part of a wide range of cultural food menus. The primary aim of this study is to compare the own-and cross-price elasticity of eggs between individuals participating in federal food assistance programs and those not participating in these programs. Our secondary aims are to 1 compare the own- and cross-price elasticity of eggs between overweight/obese individuals and non-overweight/obese individuals, 2 examine whether delay discounting moderates the effect of income on own- and cross-price elasticity, 3 examine whether subjective social status moderates the effect of participation in federal food assistance programs on the purchase of high nutrient-dense foods, and 4 examine whether usual psychological stress level moderates the effect of subjective social status on the purchase of high-nutrient dense foods. The results of this study will provide information about the drivers of food demand among low-income adults. A better understanding of these drivers is needed to develop effective nutrition interventions for this large population. Keywords: Price elasticity, Food assistance, Egg, Obesity, Social status, Stress

  8. Program summaries for 1979: energy sciences programs

    Energy Technology Data Exchange (ETDEWEB)

    1979-12-01

    This report describes the objectives of the various research programs being conducted by the Chemical Sciences, Metallurgy and Materials Science, and Process Science divisions of the BNL Dept. of Energy and Environment. Some of the more significant accomplishments during 1979 are also reported along with plans for 1980. Some of the topics under study include porphyrins, combustion, coal utilization, superconductors, semiconductors, coal, conversion, fluidized-bed combustion, polymers, etc. (DLC)

  9. NEK AOV program

    International Nuclear Information System (INIS)

    Fable, D.; Andric, A.; Prah, M.; Habinc, M.

    2002-01-01

    Air Operated Valves (AOVs) are used in a wide variety of applications in nuclear power plants. Some AOVs perform important functions in safety and non-safety related systems which could affect initiating event frequencies, accident mitigation and radiological releases. A review of lessons learned from nuclear plant MOV programs and pilot AOV programs indicates that AOV performance can be enhanced via improvements in valve and actuator sizing, setup, testing and maintenance. Nuklearna elektrarna Krsko has decided to develop an AOV program on the basis of Joint Owners. Group (JOG) AOV Program, which identifies nine key elements for successful implementation. The first step in establishing an AOV Program is to identify and categorize the plant AOVs for evaluation. Performed categorization in NEK has resulted with Preliminary AOV Scope. Important part of NEK AOV Program is NEK AOV Database. For the time being, basic structure with tables, queries, forms, reports and relationships has been created. Further development will be coordinated with development of NEK AOV Program Methodology.(author)

  10. Programming by Numbers -- A Programming Method for Complete Novices

    NARCIS (Netherlands)

    Glaser, Hugh; Hartel, Pieter H.

    2000-01-01

    Students often have difficulty with the minutiae of program construction. We introduce the idea of `Programming by Numbers', which breaks some of the programming process down into smaller steps, giving such students a way into the process of Programming in the Small. Programming by Numbers does not

  11. Extreme Programming: Maestro Style

    Science.gov (United States)

    Norris, Jeffrey; Fox, Jason; Rabe, Kenneth; Shu, I-Hsiang; Powell, Mark

    2009-01-01

    "Extreme Programming: Maestro Style" is the name of a computer programming methodology that has evolved as a custom version of a methodology, called extreme programming that has been practiced in the software industry since the late 1990s. The name of this version reflects its origin in the work of the Maestro team at NASA's Jet Propulsion Laboratory that develops software for Mars exploration missions. Extreme programming is oriented toward agile development of software resting on values of simplicity, communication, testing, and aggressiveness. Extreme programming involves use of methods of rapidly building and disseminating institutional knowledge among members of a computer-programming team to give all the members a shared view that matches the view of the customers for whom the software system is to be developed. Extreme programming includes frequent planning by programmers in collaboration with customers, continually examining and rewriting code in striving for the simplest workable software designs, a system metaphor (basically, an abstraction of the system that provides easy-to-remember software-naming conventions and insight into the architecture of the system), programmers working in pairs, adherence to a set of coding standards, collaboration of customers and programmers, frequent verbal communication, frequent releases of software in small increments of development, repeated testing of the developmental software by both programmers and customers, and continuous interaction between the team and the customers. The environment in which the Maestro team works requires the team to quickly adapt to changing needs of its customers. In addition, the team cannot afford to accept unnecessary development risk. Extreme programming enables the Maestro team to remain agile and provide high-quality software and service to its customers. However, several factors in the Maestro environment have made it necessary to modify some of the conventional extreme-programming

  12. NEWTONP - CUMULATIVE BINOMIAL PROGRAMS

    Science.gov (United States)

    Bowerman, P. N.

    1994-01-01

    The cumulative binomial program, NEWTONP, is one of a set of three programs which calculate cumulative binomial probability distributions for arbitrary inputs. The three programs, NEWTONP, CUMBIN (NPO-17555), and CROSSER (NPO-17557), can be used independently of one another. NEWTONP can be used by statisticians and users of statistical procedures, test planners, designers, and numerical analysts. The program has been used for reliability/availability calculations. NEWTONP calculates the probably p required to yield a given system reliability V for a k-out-of-n system. It can also be used to determine the Clopper-Pearson confidence limits (either one-sided or two-sided) for the parameter p of a Bernoulli distribution. NEWTONP can determine Bayesian probability limits for a proportion (if the beta prior has positive integer parameters). It can determine the percentiles of incomplete beta distributions with positive integer parameters. It can also determine the percentiles of F distributions and the midian plotting positions in probability plotting. NEWTONP is designed to work well with all integer values 0 < k <= n. To run the program, the user simply runs the executable version and inputs the information requested by the program. NEWTONP is not designed to weed out incorrect inputs, so the user must take care to make sure the inputs are correct. Once all input has been entered, the program calculates and lists the result. It also lists the number of iterations of Newton's method required to calculate the answer within the given error. The NEWTONP program is written in C. It was developed on an IBM AT with a numeric co-processor using Microsoft C 5.0. Because the source code is written using standard C structures and functions, it should compile correctly with most C compilers. The program format is interactive. It has been implemented under DOS 3.2 and has a memory requirement of 26K. NEWTONP was developed in 1988.

  13. The Canadian safeguards program

    International Nuclear Information System (INIS)

    Zarecki, C.W.; Smith, R.M.

    1981-12-01

    In support of the Treaty on the Non-Proliferation of Nuclear Weapons Canada provides technical support to the International Atomic Energy Agency for the development of safeguards relevant to Canadian designed and built nuclear facilities. Some details of this program are discussed, including the philosophy and development of CANDU safeguards systems; the unique equipment developed for these systems; the provision of technical experts; training programs; liaison with other technical organizations; research and development; implementation of safeguards systems at various nuclear facilities; and the anticipated future direction of the safeguards program

  14. Designing computer programs

    CERN Document Server

    Haigh, Jim

    1994-01-01

    This is a book for students at every level who are learning to program for the first time - and for the considerable number who learned how to program but were never taught to structure their programs. The author presents a simple set of guidelines that show the programmer how to design in a manageable structure from the outset. The method is suitable for most languages, and is based on the widely used 'JSP' method, to which the student may easily progress if it is needed at a later stage.Most language specific texts contain very little if any information on design, whilst books on des

  15. Programming with Intervals

    Science.gov (United States)

    Matsakis, Nicholas D.; Gross, Thomas R.

    Intervals are a new, higher-level primitive for parallel programming with which programmers directly construct the program schedule. Programs using intervals can be statically analyzed to ensure that they do not deadlock or contain data races. In this paper, we demonstrate the flexibility of intervals by showing how to use them to emulate common parallel control-flow constructs like barriers and signals, as well as higher-level patterns such as bounded-buffer producer-consumer. We have implemented intervals as a publicly available library for Java and Scala.

  16. Beginning Swift programming

    CERN Document Server

    Lee, Wei-Meng

    2014-01-01

    Enter the Swift future of iOS and OS X programming Beginning Swift Programming is your ideal starting point for creating Mac, iPhone, and iPad apps using Apple's new Swift programming language. Written by an experienced Apple developer and trainer, this comprehensive guide explains everything you need to know to jumpstart the creation of your app idea. Coverage includes data types, strings and characters, operators and functions, arrays and dictionaries, control flow, and looping, with expert guidance on classes, objects, class inheritance, closures, protocols, and generics. This succinct - ye

  17. Practical C++ Programming

    CERN Document Server

    Oualline, Steve

    2003-01-01

    C++ is a powerful, highly flexible, and adaptable programming language that allows software engineers to organize and process information quickly and effectively. But this high-level language is relatively difficult to master, even if you already know the C programming language. The 2nd edition of Practical C++ Programming is a complete introduction to the C++ language for programmers who are learning C++. Reflecting the latest changes to the C++ standard, this 2nd edition takes a useful down-to-earth approach, placing a strong emphasis on how to design clean, elegant code. In short, to-th

  18. Cumulative Poisson Distribution Program

    Science.gov (United States)

    Bowerman, Paul N.; Scheuer, Ernest M.; Nolty, Robert

    1990-01-01

    Overflow and underflow in sums prevented. Cumulative Poisson Distribution Program, CUMPOIS, one of two computer programs that make calculations involving cumulative Poisson distributions. Both programs, CUMPOIS (NPO-17714) and NEWTPOIS (NPO-17715), used independently of one another. CUMPOIS determines cumulative Poisson distribution, used to evaluate cumulative distribution function (cdf) for gamma distributions with integer shape parameters and cdf for X (sup2) distributions with even degrees of freedom. Used by statisticians and others concerned with probabilities of independent events occurring over specific units of time, area, or volume. Written in C.

  19. New atmospheric program

    Science.gov (United States)

    The National Science Foundation's Division of Atmospheric Sciences has established an Upper Atmospheric Facilities program within its Centers and Facilities section. The program will support the operation of and the scientific research that uses the longitudinal chain of incoherent scatter radars. The program also will ensure that the chain is maintained as a state-of-the-art research tool available to all interested and qualified scientists.For additional information, contact Richard A. Behnke, Division of Atmospheric Sciences, National Science Foundation, 1800 G Street, N.W., Washington, DC 20550 (telephone: 202-357-7390).

  20. Vinca nuclear decommissioning program

    International Nuclear Information System (INIS)

    Pesic, M.; Subotic, K.; Sotic, O.; Plecas, I.; Ljubenov, V.; Peric, A.

    2002-01-01

    In this paper a preliminary program for the nuclear decommissioning in The Vinca Institute of Nuclear Sciences is presented. Proposed Projects and Activities, planned to be done in the next 10 years within the frames of the Program, should improve nuclear and radiation safety and should solve the main problems that have arisen in the previous period. Project of removal of irradiated spent nuclear fuel from the RA reactor, as a first step in all possible decommissioning strategies and the main activity in the first two-three years of the Program realization, is considered in more details. (author)